Science.gov

Sample records for 200-gram pu drums

  1. Criticality Safety Controls for 55-Gallon Drums with a Mass Limit of 200 grams Pu-239

    SciTech Connect

    Chou, P

    2011-12-14

    The following 200-gram Pu drum criticality safety controls are applicable to RHWM drum storage operations: (1) Mass (Fissile/Pu) - each 55-gallon drum or its equivalent shall be limited to 200 gram Pu or Pu equivalent; (2) Moderation - Hydrogen materials with a hydrogen density greater than that (0.133 g H/cc) of polyethylene and paraffin are not allowed and hydrogen materials with a hydrogen density no greater than that of polyethylene and paraffin are allowed with unlimited amounts; (3) Interaction - a spacing of 30-inches (76 cm) is required between arrays and 200-gram Pu drums shall be placed in arrays for 200-gram Pu drums only (no mingling of 200-gram Pu drums with other drums not meeting the drum controls associated with the 200-gram limit); (4) Reflection - no beryllium and carbon/graphite (other than the 50-gram waiver amount) is allowed, (note that Nat-U exceeding the waiver amount is allowed when its U-235 content is included in the fissile mass limit of 200 grams); and (5) Geometry - drum geometry, only 55-gallon drum or its equivalent shall be used and array geometry, 55-gallon drums are allowed for 2-high stacking. Steel waste boxes may be stacked 3-high if constraint.

  2. Criticality Safety Evaluations on the Use of 200-gram Pu Mass Limit for RHWM Waste Storage Operations

    SciTech Connect

    Chou, P

    2011-12-14

    This work establishes the criticality safety technical basis to increase the fissile mass limit from 120 grams to 200 grams for Type A 55-gallon drums and their equivalents. Current RHWM fissile mass limit is 120 grams Pu for Type A 55-gallon containers and their equivalent. In order to increase the Type A 55-gallon drum limit to 200 grams, a few additional criticality safety control requirements are needed on moderators, reflectors, and array controls to ensure that the 200-gram Pu drums remain criticality safe with inadvertent criticality remains incredible. The purpose of this work is to analyze the use of 200-gram Pu drum mass limit for waste storage operations in Radioactive and Hazardous Waste Management (RHWM) Facilities. In this evaluation, the criticality safety controls associated with the 200-gram Pu drums are established for the RHWM waste storage operations. With the implementation of these criticality safety controls, the 200-gram Pu waste drum storage operations are demonstrated to be criticality safe and meet the double-contingency-principle requirement per DOE O 420.1.

  3. Determining site-specific drum loading criteria for storing combustible {sup 238}Pu waste

    SciTech Connect

    Marshall, R.S.; Callis, E.L.; Cappis, J.H.; Espinoza, J.M.; Foltyn, E.M.; Reich, B.T.; Smith, M.C.

    1994-02-01

    Waste containing hydrogenous-combustible material contaminated with {sup 238}Pu can generate hydrogen gas at appreciable rates through alpha radiolysis. To ensure safe transportation of WIPP drums, the limit for {sup 238}Pu-combustible waste published in the WIPP TRUPACT-11 CONTENT (TRUCON) CODES is 21 milliwafts per 55 gallon drum. This corresponds to about 45 milligrams of {sup 238}PuO{sub 2} used for satellite heat source-electrical generators. The Los Alamos waste storage site adopted a {sup 238}Pu waste storage criteria based on these TRCUCON codes. However, reviews of the content in drums of combustible waste generated during heat source assembly at Los Alamos showed the amount of {sup 238}Pu is typically much greater than 45 milligrams. It is not feasible to appreciably reduce Los Alamos {sup 238}Pu waste drum loadings without significantly increasing waste volumes or introducing unsafe practices. To address this concern, a series of studies were implemented to evaluate the applicability of the TRUCON limits for storage of this specific waste. Addressed in these evaluations were determination of the hydrogen generation rate, hydrogen diffusion rates through confinement layers and vent filters, and packaging requirements specific to Los Alamos generated {sup 238}Pu contaminated combustible waste. These studies also showed that the multiple-layer packaging practices in use at Los Alamos could be relaxed without significantly increasing the risk of contamination. Based on a model developed to predict H{sub 2} concentrations in packages and drum headspace, the site specific effective hydrogen generation rate, and hydrogen-diffusion values, and revising the waste packaging practices, we were able to raise the safe loading limit for {sup 238}Pu waste drums for on site storage to the gram levels typical of currently generated {sup 238}Pu waste.

  4. Feasibility study of 235U and 239Pu characterization in radioactive waste drums using neutron-induced fission delayed gamma rays

    NASA Astrophysics Data System (ADS)

    Nicol, T.; Pérot, B.; Carasco, C.; Brackx, E.; Mariani, A.; Passard, C.; Mauerhofer, E.; Collot, J.

    2016-10-01

    This paper reports a feasibility study of 235U and 239Pu characterization in 225 L bituminized waste drums or 200 L concrete waste drums, by detecting delayed fission gamma rays between the pulses of a deuterium-tritium neutron generator. The delayed gamma yields were first measured with bare samples of 235U and 239Pu in REGAIN, a facility dedicated to the assay of 118 L waste drums by Prompt Gamma Neutron Activation Analysis (PGNAA) at CEA Cadarache, France. Detectability in the waste drums is then assessed using the MCNPX model of MEDINA (Multi Element Detection based on Instrumental Neutron Activation), another PGNAA cell dedicated to 200 L drums at FZJ, Germany. For the bituminized waste drum, performances are severely hampered by the high gamma background due to 137Cs, which requires the use of collimator and shield to avoid electronics saturation, these elements being very penalizing for the detection of the weak delayed gamma signal. However, for lower activity concrete drums, detection limits range from 10 to 290 g of 235U or 239Pu, depending on the delayed gamma rays of interest. These detection limits have been determined by using MCNPX to calculate the delayed gamma useful signal, and by measuring the experimental gamma background in MEDINA with a 200 L concrete drum mock-up. The performances could be significantly improved by using a higher interrogating neutron emission and an optimized experimental setup, which would allow characterizing nuclear materials in a wide range of low and medium activity waste packages.

  5. Unvented Drum Handling Plan

    SciTech Connect

    MCDONALD, K.M.

    2000-08-01

    This drum-handling plan proposes a method to deal with unvented transuranic drums encountered during retrieval of drums. Finding unvented drums during retrieval activities was expected, as identified in the Transuranic (TRU) Phase I Retrieval Plan (HNF-4781). However, significant numbers of unvented drums were not expected until excavation of buried drums began. This plan represents accelerated planning for management of unvented drums. A plan is proposed that manages unvented drums differently based on three categories. The first category of drums is any that visually appear to be pressurized. These will be vented immediately, using either the Hanford Fire Department Hazardous Materials (Haz. Mat.) team, if such are encountered before the facilities' capabilities are established, or using internal capabilities, once established. To date, no drums have been retrieved that showed signs of pressurization. The second category consists of drums that contain a minimal amount of Pu isotopes. This minimal amount is typically less than 1 gram of Pu, but may be waste-stream dependent. Drums in this category are assayed to determine if they are low-level waste (LLW). LLW drums are typically disposed of without venting. Any unvented drums that assay as TRU will be staged for a future venting campaign, using appropriate safety precautions in their handling. The third category of drums is those for which records show larger amounts of Pu isotopes (typically greater than or equal to 1 gram of Pu). These are assumed to be TRU and are not assayed at this point, but are staged for a future venting campaign. Any of these drums that do not have a visible venting device will be staged awaiting venting, and will be managed under appropriate controls, including covering the drums to protect from direct solar exposure, minimizing of container movement, and placement of a barrier to restrict vehicle access. There are a number of equipment options available to perform the venting. The

  6. CSER 96-027: storage of cemented plutonium residue containers in 55 gallon drums

    SciTech Connect

    Watson, W.T.

    1997-01-20

    A nuclear criticality safety analysis has been performed for the storage of residual plutonium cementation containers, produced at the Plutonium Finishing Plant, in 55 gallon drums. This CSER increases the limit of total plutonium stored in each 55 gallon drum from 100 to 200 grams.

  7. Drum drop test report

    SciTech Connect

    McBeath, R.S.

    1995-02-28

    Testing was performed to determine actual damage to drums when dropped from higher than currently stacked elevations. The drum configurations were the same as they are placed in storage; single drums and four drums banded to a pallet. Maximum drop weights were selected based on successful preliminary tests. Material was lost from each of the single drum tests while only a small amount of material was lost from one of the pelletized drums. The test results are presented in this report. This report also provides recommendations for further testing to determine the appropriate drum weight which can be stored on a fourth tier.

  8. Neutron absorber inserts for 55-gal drums

    SciTech Connect

    Wilson, R.E.; Kim, Y.S.; Toffer, H.

    2000-07-01

    Transport and temporary storage of more than 200 g of fissile material in 55-gal drums at the Rocky Flats Environmental Technology Site (RFETS) have received significant attention during the cleanup mission. This paper discusses successful applications and results of extensive computer studies. Interim storage and movement of fissile material in excess of standard drum limits (200 g) in a safe configuration have been accomplished using special drum inserts. Such inserts have constrained the contents of a drum to two 4-{ell} bottles. The content of the bottles was limited to 600 g Pu or U in solution or a total of 1200 g for the entire drum. The inserts were a simple design constructed of stainless steel, forming a vertical cylindrical pipe into which two bottles, one on top of the other, could be centered in the drum. The remaining drum volume was configured to preclude any additional bottle placement external to the vertical cylinder. Such inserts in drums were successfully used in moving high-concentration solution from one building to another for chemical processing. Concern about the knowledge of fissile material concentration in bottles prompted another study for drum inserts. The past practice had been to load up to fourteen 4-{ell} bottles into 55-gal drums, provided the fissile material concentration was <6 g fissile/{ell}, and the total drum contents of 200 g fissile was not exceeded. Only one determination of the solution concentration was needed. An extensive safety analysis concluded that a single measurement of bottle content could not ensure compliance with double-contingency-criterion requirements. A second determination of the bottle contents was required before bottles could be placed in a 55-gal drum. Al alternative to a dual-measurement protocol, which is for bolstering administrative control, was to develop an engineered safety feature that would eliminate expensive tests and administrative decisions. A drum insert design was evaluated that

  9. Waste drum refurbishment

    SciTech Connect

    Whitmill, L.J.

    1996-10-18

    Low-carbon steel, radioactive waste containers (55-gallon drums) are experiencing degradation due to moisture and temperature fluctuations. With thousands of these containers currently in use; drum refurbishment becomes a significant issue for the taxpayer and stockholders. This drum refurbishment is a non-intrusive, portable process costing between 1/2 and 1/25 the cost of repackaging, depending on the severity of degradation. At the INEL alone, there are an estimated 9,000 drums earmarked for repackaging. Refurbishing drums rather than repackaging can save up to $45,000,000 at the INEL. Based on current but ever changing WIPP Waste Acceptance Criteria (WAC), this drum refurbishment process will restore drums to a WIPP acceptable condition plus; drums with up to 40% thinning o the wall can be refurbished to meet performance test requirements for DOT 7A Type A packaging. A refurbished drum provides a tough, corrosion resistant, waterproof container with longer storage life and an additional containment barrier. Drums are coated with a high-pressure spray copolymer material approximately .045 inches thick. Increase in internal drum temperature can be held to less than 15 F. Application can be performed hands-on or the equipment is readily adaptable and controllable for remote operations. The material dries to touch in seconds, is fully cured in 48 hours and has a service temperature of {minus}60 to 500 F. Drums can be coated with little or no surface preparation. This research was performed on drums however research results indicate the coating is very versatile and compatible with most any material and geometry. It could be used to provide abrasion resistance, corrosion protection and waterproofing to almost anything.

  10. Hot air drum evaporator

    DOEpatents

    Black, Roger L.

    1981-01-01

    An evaporation system for aqueous radioactive waste uses standard 30 and 55 gallon drums. Waste solutions form cascading water sprays as they pass over a number of trays arranged in a vertical stack within a drum. Hot dry air is circulated radially of the drum through the water sprays thereby removing water vapor. The system is encased in concrete to prevent exposure to radioactivity. The use of standard 30 and 55 gallon drums permits an inexpensive compact modular design that is readily disposable, thus eliminating maintenance and radiation build-up problems encountered with conventional evaporation systems.

  11. Lawrence Livermore National Laboratory Experience Using 30-Gallon Drum Neutron Multiplicity Counter for Measuring Plutonium-Bearing Salts

    SciTech Connect

    Dearborn, D M; Keeton, S C

    2004-06-22

    Lawrence Livermore National Laboratory (LLNL) has been performing accountability measurements of plutonium (Pu) -bearing items with the 30-gallon drum neutron multiplicity counter (NMC) since August 1998. A previous paper focused on the LLNL experience with Pu-bearing oxide and metal items. This paper expands on the LLNL experience with Pu-bearing salts containing low masses of Pu. All Pu-bearing salts used in this study were measured using calorimetry and gamma isotopic analyses (Cal/Iso) as well as the 30-gallon drum NMC. The Cal/Iso values were treated as being the true measure of Pu content because of the inherent high accuracy of the Cal/Iso technique, even at low masses of Pu, when measured over a sufficient period of time. Unfortunately, the long time period required to achieve high accuracy from Cal/Iso can impact other required accountability measurements. The 30-gallon drum NMC is a much quicker system for making accountability measurements of a Pu-bearing salt and might be a desirable tradeoff. The accuracy of 30-gallon drum NMC measurements of Pu-bearing salts, relative to that of Cal/Iso, is presented in relation to the mass range and alpha associated with each item. Conclusions drawn from the use of the 30-gallon drum NMC for accountability measurements of salts are also included.

  12. Drums for Peace.

    ERIC Educational Resources Information Center

    Kneidek, Tony

    1997-01-01

    Describes a Lakota family tradition of passing on the responsibilities of being caretaker of the drum of the Fool Soldiers (Akicita Heyoka), warriors who risked their lives for peace in 1862. The drum and its ceremonial use symbolize nonviolence and cross-cultural understanding between the races and are a part of Lakota spiritual heritage. (SAS)

  13. Drum lid removal tool

    DOEpatents

    Pella, Bernard M.; Smith, Philip D.

    2010-08-24

    A tool for removing the lid of a metal drum wherein the lid is clamped over the drum rim without protruding edges, the tool having an elongated handle with a blade carried by an angularly positioned holder affixed to the midsection of the handle, the blade being of selected width to slice between lid lip and the drum rim and, when the blade is so positioned, upward motion of the blade handle will cause the blade to pry the lip from the rim and allow the lid to be removed.

  14. FAILURE ANALYSIS: WASTEWATER DRUM BULGING

    SciTech Connect

    Vormelker, P

    2008-09-15

    A 55 gallon wastewater drum lid was found to be bulged during storage in a remote area. Drum samples were obtained for analysis. The interior surface of these samples revealed blistering and holes in the epoxy phenolic drum liner and corrosion of the carbon steel drum. It is suspected that osmotic pressure drove permeation of the water through the epoxy phenolic coating which was weakened from exposure to low pH water. The coating failed at locations throughout the drum interior. Subsequent corrosion of the carbon steel released hydrogen which pressurized the drum causing deformation of the drum lid. Additional samples from other wastewater drums on the same pallet were also evaluated and limited corrosion was visible on the interior surfaces. It is suspected that, with time, the corrosion would have advanced to cause pressurization of these sealed drums.

  15. Rotating drum filter

    DOEpatents

    Anson, Donald

    1990-01-01

    A perforated drum (10) rotates in a coaxial cylindrical housing (18) having three circumferential ports (19,22,23), and an axial outlet (24) at one end. The axis (11) is horizontal. A fibrous filter medium (20) is fed through a port (19) on or near the top of the housing (81) by a distributing mechanism (36) which lays a uniform mat (26) of the desired thickness onto the rotating drum (10). This mat (26) is carried by the drum (10) to a second port (23) through which dirty fluid (13) enters. The fluid (13) passes through the filter (26) and the cleaned stream (16) exits through the open end (15) of the drum (10) and the axial port (24) in the housing (18). The dirty filter material (20) is carried on to a third port (22) near the bottom of the housing (18) and drops into a receiver (31) from which it is continuously removed, cleaned (30), and returned (32) to the charging port (36) at the top. To support the filter mat, the perforated cylinder may carry a series of tines (40), shaped blades (41), or pockets, so that the mat (26) will not fall from the drum (10) prematurely. To minimize risk of mat failure, the fluid inlet port (23) may be located above the horizontal centerline (11).

  16. Rotary drum separator system

    NASA Technical Reports Server (NTRS)

    Barone, Michael R. (Inventor); Murdoch, Karen (Inventor); Scull, Timothy D. (Inventor); Fort, James H. (Inventor)

    2009-01-01

    A rotary phase separator system generally includes a step-shaped rotary drum separator (RDS) and a motor assembly. The aspect ratio of the stepped drum minimizes power for both the accumulating and pumping functions. The accumulator section of the RDS has a relatively small diameter to minimize power losses within an axial length to define significant volume for accumulation. The pumping section of the RDS has a larger diameter to increase pumping head but has a shorter axial length to minimize power losses. The motor assembly drives the RDS at a low speed for separating and accumulating and a higher speed for pumping.

  17. Clamshell closure for metal drum

    DOEpatents

    Blanton, Paul S

    2014-09-30

    Closure ring to retain a lid in contact with a metal drum in central C-section conforming to the contact area between a lid and the rim of a drum and further having a radially inwardly directed flange and a vertically downwardly directed flange attached to the opposite ends of the C-section. The additional flanges reinforce the top of the drum by reducing deformation when the drum is dropped and maintain the lid in contact with the drum. The invention is particularly valuable in transportation and storage of fissile material.

  18. Solar drum positioner mechanisms

    NASA Technical Reports Server (NTRS)

    Briggs, L. W.

    1982-01-01

    The need for additional power on spinning satellites required development of deployable solar arrays activated, as on a 3-axis vehicle, after separation from a booster or shuttle orbiter. Mechanisms were developed for telescopically extending a secondary 36.3 kg (80 lb.), 2.13 m (84 in.) diameter spinning solar drum for a distance of 2.0 m (80 in.) or more along the spin axis. After extension, the system has the capability of dynamically controlling the drum tilt angle about the spin axis to provide precision in-orbit balancing of the spacecraft. This approach was selected for the SBS, ANIK C, ANIK D, WESTAR B and PALAPA B satellites. It was successfully demonstrated during the in orbit deployment of the aft solar panels of the SBS F-3 and F-1 satellites, subsequent to the November 1980 and September 1981 launches.

  19. Pu-238 assay performance with the Canberra IQ3 system

    SciTech Connect

    Booth, L.; Gillespie, B.; Seaman, G.

    1997-11-01

    Canberra Industries has recently completed a demonstration project at the Westinghouse Savannah River Site (WSRC) to characterize 55-gallon drums containing Pu-238 contaminated waste. The goal of this project was to detect and quantify Pu-238 contaminated waste. The goal of this project was to detect and quantify Pu-238 waste to detection limits of less than 50 nCi/g using gamma assay techniques. This would permit reclassification of these drums from transuranic (TRU) waste to low-level waste (LLW). The instrument used for this assay was a Canberra IQ3 high sensitivity gamma assay system, mounted in a trailer. The results of the measurements demonstrate achievement of detection levels as low as 1 nCi/g for low density waste drums, and good correlation with known concentrations in several test drums. In addition, the data demonstrates significant advantages for using large area low-energy germanium detectors for achieving the lowest possible MDAs for gamma rays in the 80-250 keV range. 1 fig., 2 tabs.

  20. 23. BACKING DRUM IN FOREGROUND. MAIN ENGINE STEP DRUM IN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    23. BACKING DRUM IN FOREGROUND. MAIN ENGINE STEP DRUM IN CENTER. TO RIGHT NOTE CYLINDER, PISTON ROD CROSSHEAD. AT END OF CRANKSHAFT NOTE WRIST PIN AND CRANE DISK. - Dredge CINCINNATI, Docked on Ohio River at foot of Lighthill Street, Pittsburgh, Allegheny County, PA

  1. Anisotropy in rotating drums

    NASA Astrophysics Data System (ADS)

    Povall, Timothy; McBride, Andrew; Govender, Indresan

    2015-11-01

    An anisotropic relationship between the stress and the strain rate has been observed in two-dimensional simulations of rotating drums. The objective of this work is to investigate the structure of the constitutive relation using three-dimensional discrete-element-method simulations of a rotating drum containing identical rigid spheres for a range of rotational speeds. Anisotropy is quantified from the alignment of the stress and strain rate tensors, with the strain rate computed using a least-squares fit. It is shown that in certain regions there is a strong anisotropic relationship, regardless of the speed of rotation. The effective friction coefficient is examined in order to determine the phase space in which the μ (I) rheology is valid. Lastly, a depth-averaged approach through the flowing layer is employed to determine the relationship between the velocity tangential to the equilibrium surface and the height of the flowing layer. A power-law relationship that approaches linear at high speeds is observed. Supported by NRF/DST Scarce Skills (South Africa).

  2. Overview of advanced technologies for stabilization of {sup 238}Pu-contaminated waste

    SciTech Connect

    Ramsey, K.B.; Foltyn, E.M.; Heslop, J.M.

    1998-02-01

    This paper presents an overview of potential technologies for stabilization of {sup 238}Pu-contaminated waste. Los Alamos National Laboratory (LANL) has processed {sup 238}PuO{sub 2} fuel into heat sources for space and terrestrial uses for the past several decades. The 88-year half-life of {sup 238}Pu and thermal power of approximately 0.6 watts/gram make this isotope ideal for missions requiring many years of dependable service in inaccessible locations. However, the same characteristic which makes {sup 238}Pu attractive for heat source applications, the high Curie content (17 Ci/gram versus 0.06 Ci/gram for 239{sup Pu}), makes disposal of {sup 238}Pu-contaminated waste difficult. Specifically, the thermal load limit on drums destined for transport to the Waste Isolation Pilot Plant (WIPP), 0.23 gram per drum for combustible waste, is impossible to meet for nearly all {sup 238}Pu-contaminated glovebox waste. Use of advanced waste treatment technologies including Molten Salt Oxidation (MSO) and aqueous chemical separation will eliminate the combustible matrix from {sup 238}Pu-contaminated waste and recover kilogram quantities of {sup 238}PuO{sub 2} from the waste stream. A conceptual design of these advanced waste treatment technologies will be presented.

  3. Overview of advanced technologies for stabilization of 238Pu-contaminated waste

    NASA Astrophysics Data System (ADS)

    Ramsey, Kevin B.; Foltyn, Elizabeth M.; Heslop, J. Mark

    1998-01-01

    This paper presents an overview of potential technologies for stabilization of 238Pu-contaminated waste. Los Alamos National Laboratory (LANL) has processed 238PuO2 fuel into heat sources for space and terrestrial uses for the past several decades. The 88-year half-life of 238Pu and thermal power of approximately 0.6 watts/gram make this isotope ideal for missions requiring many years of dependable service in inaccessible locations. However, the same characteristic which makes 238Pu attractive for heat source applications, the high Curie content (17 Ci/gram versus 0.06 Ci/gram for 239Pu), makes disposal of 238Pu-contaminated waste difficult. Specifically, the thermal load limit on drums destined for transport to the Waste Isolation Pilot Plant (WIPP), 0.23 gram per drum for combustible waste, is impossible to meet for nearly all 238Pu-contaminated glovebox waste. Use of advanced waste treatment technologies including Molten Salt Oxidation (MSO) and aqueous chemical separation will eliminate the combustible matrix from 238Pu-contaminated waste and recover kilogram quantities of 238PuO2 from the waste stream. A conceptual design of these advanced waste treatment technologies will be presented.

  4. 21 CFR 886.1200 - Optokinetic drum.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Optokinetic drum. 886.1200 Section 886.1200 Food... DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1200 Optokinetic drum. (a) Identification. An optokinetic drum is a drum-like device covered with alternating white and dark stripes or pictures that can...

  5. 21 CFR 886.1200 - Optokinetic drum.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Optokinetic drum. 886.1200 Section 886.1200 Food... DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1200 Optokinetic drum. (a) Identification. An optokinetic drum is a drum-like device covered with alternating white and dark stripes or pictures that can...

  6. 21 CFR 886.1200 - Optokinetic drum.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Optokinetic drum. 886.1200 Section 886.1200 Food... DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1200 Optokinetic drum. (a) Identification. An optokinetic drum is a drum-like device covered with alternating white and dark stripes or pictures that can...

  7. 21 CFR 886.1200 - Optokinetic drum.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Optokinetic drum. 886.1200 Section 886.1200 Food... DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1200 Optokinetic drum. (a) Identification. An optokinetic drum is a drum-like device covered with alternating white and dark stripes or pictures that can...

  8. 21 CFR 886.1200 - Optokinetic drum.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Optokinetic drum. 886.1200 Section 886.1200 Food... DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1200 Optokinetic drum. (a) Identification. An optokinetic drum is a drum-like device covered with alternating white and dark stripes or pictures that can...

  9. Miniature rotating transmissive optical drum scanner

    NASA Technical Reports Server (NTRS)

    Lewis, Robert (Inventor); Parrington, Lawrence (Inventor); Rutberg, Michael (Inventor)

    2013-01-01

    A miniature rotating transmissive optical scanner system employs a drum of small size having an interior defined by a circumferential wall rotatable on a drum axis, an optical element positioned within the interior of the drum, and a light-transmissive lens aperture provided at an angular position in the circumferential wall of the drum for scanning a light beam to or from the optical element in the drum along a beam azimuth angle as the drum is rotated. The miniature optical drum scanner configuration obtains a wide scanning field-of-view (FOV) and large effective aperture is achieved within a physically small size.

  10. EARLY TESTS OF DRUM TYPE PACKAGINGS - THE LEWALLEN REPORT

    SciTech Connect

    Smith, A.

    2010-07-29

    The need for robust packagings for radioactive materials (RAM) was recognized from the earliest days of the nuclear industry. The U.S. Department of Energy (DOE) Rocky Flats Plant developed a packaging for shipment of Pu in the early 1960's, which became the U.S. Department of Transportation (DOT) 6M specification package. The design concepts were employed in other early packagings. Extensive tests of these at Savannah River Laboratory (now Savannah River National Laboratory) were performed in 1969 and 1970. The results of these tests were reported in 'Drum and Board-Type Insulation Overpacks of Shipping Packages for Radioactive Materials', by E. E. Lewallen. The Lewallen Report was foundational to design of subsequent drum type RAM packaging. This paper summarizes this important early study of drum type packagings. The Lewallen Report demonstrated the ability packagings employing drum and insulation board overpacks and engineered containment vessels to meet the Type B package requirements. Because of the results of the Lewallen Report, package designers showed high concern for thermal protection of 'Celotex'. Subsequent packages addressed this by following strategies like those recommended by Lewallen and by internal metal shields and supplemental, encapsulated insulation disks, as in 9975. The guidance provide by the Lewallen Report was employed in design of a large number of drum size packagings over the following three decades. With the increased public concern over transportation of radioactive materials and recognition of the need for larger margins of safety, more sophisticated and complex packages have been developed and have replaced the simple packagings developed under the Lewallen Report paradigm.

  11. Drum tie-down apparatus

    DOEpatents

    Morse, Harvey E.

    1984-01-01

    A drum tie-down apparatus for securing drum-like containers in an upright position to a floor or platform of a transportation vehicle having spaced apart cargo tie-down points. The apparatus comprises a pair of cylindrical, hollow tube segments horizontally oriented and engageable with a drum lid adjacent opposite rim edges, flexible strap segments for connecting upper and lower central portions of the tube segments together across the drum lid and a pair of elongated flexible tie-down segments, one extending horizontally through each of the tube segments, the ends thereof being attached to said spaced apart tie-down points such that end portions of the pair of tie-down segments extend downwardly and radially outwardly from the tube segments to the tie-down points.

  12. Drum tie-down apparatus

    DOEpatents

    Morse, H.E.

    A drum tie-down apparatus for securing drum-like containers in an upright position to a floor or platform of a transportation vehicle having spaced apart cargo tie-down points. The apparatus comprises a pair of cylindrical, hollow tube segments horizontally oriented and engageable with a drum lid adjacent opposite rim edges, flexible strap segments for connecting upper and lower central portions of the tube segments together across the drum lid and a pair of elongated flexible tie-down segments, one extending horizontally through each of the tube segments, the ends thereof being attached to said spaced apart tie-down points such that end portions of the pair of tie-down segments extend downwardly and radially outwardly from the tube segments to the tie-down points.

  13. Drum inspection robots: Application development

    SciTech Connect

    Hazen, F.B.; Warner, R.D.

    1996-02-01

    Throughout the Department of Energy (DOE), drums containing mixed and low level stored waste are inspected, as mandated by the Resource Conservation and Recovery Act (RCRA) and other regulations. The inspections are intended to prevent leaks by finding corrosion long before the drums are breached. The DOE Office of Science and Technology (OST) has sponsored efforts towards the development of robotic drum inspectors. This emerging application for mobile and remote sensing has broad applicability for DOE and commercial waste storage areas. Three full scale robot prototypes have been under development, and another project has prototyped a novel technique to analyze robotically collected drum images. In general, the robots consist of a mobile, self-navigating base vehicle, outfitted with sensor packages so that rust and other corrosion cues can be automatically identified. They promise the potential to lower radiation dose and operator effort required, while improving diligence, consistency, and documentation.

  14. Application of active and passive neutron non destructive assay methods to concrete radioactive waste drums

    NASA Astrophysics Data System (ADS)

    Jallu, F.; Passard, C.; Brackx, E.

    2011-09-01

    This paper deals with the application of non-destructive neutron measurement methods to control and characterize 200 l radioactive waste drums filled with a concrete matrix. Due to its composition, and particularly to hydrogen, concrete penalizes the use of such methods to quantify uranium (U) and plutonium (Pu) components, which are mainly responsible of the α-activity of the waste. The determination of the alpha activity is the main objective of neutron measurements, in view to verify acceptance criteria in surface storage. Calibration experiments of the Active Neutron Interrogation (ANI) method lead to Detection Limit Masses (DLM) of about 1 mg of 239Pu eff in the total counting mode, and of about 10 mg of 239Pu eff in the coincidence counting mode, in case of a homogeneous Pu source and measurement times between one and two hours. Monte Carlo calculation results show a very satisfactory agreement between experimental values and calculated ones. Results of the application of passive and active neutron methods to control two real drums are presented in the last part of the paper. They show a good agreement between measured data and values declared by the waste producers. The main difficulties that had to be overcome are the low neutron signal in passive and active coincidence counting modes due to concrete, the analysis of the passive neutron signal in presence of 244Cm in the drum, which is a strong spontaneous fission neutron emitter, the variation of the active background with the concrete composition, and the analysis of the active prompt neutron signal due to the simultaneous presence of U and Pu in the drums.

  15. L AREA WASTEWATER STORAGE DRUM EVALUATION

    SciTech Connect

    Vormelker, P; Cynthia Foreman, C; Zane Nelson, Z; David Hathcock, D; Dennis Vinson, D

    2007-11-30

    This report documents the determination of the cause of pressurization that led to bulging deformation of a 55 gallon wastewater drum stored in L-Area. Drum samples were sent to SRNL for evaluation. The interior surface of these samples revealed blistering and holes in the epoxy phenolic drum liner and corrosion of the carbon steel drum. It is suspected that osmotic pressure drove permeation of the water through the epoxy phenolic coating which was weakened from exposure to low pH water. The coating failed at locations throughout the drum interior. Subsequent corrosion of the carbon steel released hydrogen which pressurized the drum causing deformation of the drum lid. Additional samples from other wastewater drums on the same pallet were also evaluated and limited corrosion was visible on the interior surfaces. It is suspected that, with time, the corrosion would have advanced to cause pressurization of these sealed drums.

  16. Purification of 238Pu Oxide using the Pu Oxalate Process

    SciTech Connect

    Mew, D A; Krikorian, O H; Dodson, K E; Schmitz, J A

    2001-11-28

    The Pu oxalate process is used to remove {sup 234}U from aged {sup 238}Pu-enriched PuO{sub 2} ({sup 234}U grows into the PuO{sub 2} material with time from a-decay of {sup 238}Pu). The Pu oxalate process was first used on a mixture of weapons grade PuO{sub 2} with UO{sub 2} to work out the processing parameters. It was then applied to aged {sup 238}Pu-enriched PuO{sub 2} ({sup 238}PuO{sub 2}). The {sup 234}U content of the {sup 238}PuO{sub 2} was reduced from 13.2 wt% to 0.0254 wt%, and the Pu recovery yield was 78.5%. The process is complex and is complicated by radiolysis problems when working with {sup 238}Pu. Details of the experiments are described.

  17. Solid waste drum array fire performance

    SciTech Connect

    Louie, R.L.; Haecker, C.F.; Beitel, J.J.; Gottuck, D.T.; Rhodes, B.T.; Bayier, C.L.

    1995-09-01

    Fire hazards associated with drum storage of radioactively contaminated waste are a major concern in DOE waste storage facilities. This report is the second of two reports on fire testing designed to provide data relative to the propagation of a fire among storage drum arrays. The first report covers testing of individual drums subjected to an initiating fire and the development of the analytical methodology to predict fire propagation among storage drum arrays. This report is the second report, which documents the results of drum array fire tests. The purpose of the array tests was to confirm the analytical methodology developed by Phase I fire testing. These tests provide conclusive evidence that fire will not propagate from drum to drum unless an continuous fuel source other than drum contents is provided.

  18. Hand-Drumming to Build Community: The Story of the Whittier Drum Project

    ERIC Educational Resources Information Center

    Stone, Nathan Neil

    2005-01-01

    In this article the author shares the story of the Whittier Drum Project and how it succeeded. The Whittier Drum Project has brought the community together through the talents of youth and their dedication to drumming, and has used drumming to link professionals to their own communities. The author adapted the model to meet the therapeutic needs…

  19. Vapor generator steam drum spray head

    DOEpatents

    Fasnacht, Jr., Floyd A.

    1978-07-18

    A typical embodiment of the invention provides a combination feedwater and "cooldown" water spray head that is centrally disposed in the lower portion of a nuclear power plant steam drum. This structure not only discharges the feedwater in the hottest part of the steam drum, but also increases the time required for the feedwater to reach the steam drum shell, thereby further increasing the feedwater temperature before it contacts the shell surface, thus reducing thermal shock to the steam drum structure.

  20. 30 CFR 57.19011 - Drum flanges.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Drum flanges. 57.19011 Section 57.19011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND....19011 Drum flanges. Flanges on drums shall extend radially a minimum of 4 inches or three rope...

  1. 30 CFR 57.19011 - Drum flanges.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drum flanges. 57.19011 Section 57.19011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND....19011 Drum flanges. Flanges on drums shall extend radially a minimum of 4 inches or three rope...

  2. 30 CFR 56.19012 - Grooved drums.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Grooved drums. 56.19012 Section 56.19012 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... § 56.19012 Grooved drums. Where grooved drums are used, the grooves shall be of suitable size and...

  3. 30 CFR 56.19012 - Grooved drums.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Grooved drums. 56.19012 Section 56.19012 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... § 56.19012 Grooved drums. Where grooved drums are used, the grooves shall be of suitable size and...

  4. 30 CFR 57.19012 - Grooved drums.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Grooved drums. 57.19012 Section 57.19012 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Hoists § 57.19012 Grooved drums. Where grooved drums are used, the grooves shall be of suitable size...

  5. 30 CFR 57.19011 - Drum flanges.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Drum flanges. 57.19011 Section 57.19011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND....19011 Drum flanges. Flanges on drums shall extend radially a minimum of 4 inches or three rope...

  6. 30 CFR 56.19012 - Grooved drums.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Grooved drums. 56.19012 Section 56.19012 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... § 56.19012 Grooved drums. Where grooved drums are used, the grooves shall be of suitable size and...

  7. 30 CFR 56.19011 - Drum flanges.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Drum flanges. 56.19011 Section 56.19011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... Drum flanges. Flanges on drums shall extend radially a minimum of 4 inches or three rope...

  8. 30 CFR 57.19012 - Grooved drums.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Grooved drums. 57.19012 Section 57.19012 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Hoists § 57.19012 Grooved drums. Where grooved drums are used, the grooves shall be of suitable size...

  9. Percussion Discussion: Using Drums To Reconnect Youth.

    ERIC Educational Resources Information Center

    Wilbur, John; Harris, Tom

    1998-01-01

    Reports on a therapeutic program for juvenile offenders that uses drum playing and drum building to provide alternatives for youth activities. Drums play five important roles for youth: creating a sense of community, reconnecting with history and heritage, promoting healing, educating, and celebrating victories or rites of passage. Provides…

  10. 30 CFR 57.19011 - Drum flanges.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Drum flanges. 57.19011 Section 57.19011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND....19011 Drum flanges. Flanges on drums shall extend radially a minimum of 4 inches or three rope...

  11. 30 CFR 56.19011 - Drum flanges.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Drum flanges. 56.19011 Section 56.19011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... Drum flanges. Flanges on drums shall extend radially a minimum of 4 inches or three rope...

  12. 30 CFR 57.19011 - Drum flanges.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Drum flanges. 57.19011 Section 57.19011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND....19011 Drum flanges. Flanges on drums shall extend radially a minimum of 4 inches or three rope...

  13. 30 CFR 56.19011 - Drum flanges.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drum flanges. 56.19011 Section 56.19011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... Drum flanges. Flanges on drums shall extend radially a minimum of 4 inches or three rope...

  14. 30 CFR 56.19012 - Grooved drums.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Grooved drums. 56.19012 Section 56.19012 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... § 56.19012 Grooved drums. Where grooved drums are used, the grooves shall be of suitable size and...

  15. 30 CFR 57.19012 - Grooved drums.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Grooved drums. 57.19012 Section 57.19012 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Hoists § 57.19012 Grooved drums. Where grooved drums are used, the grooves shall be of suitable size...

  16. 30 CFR 56.19012 - Grooved drums.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Grooved drums. 56.19012 Section 56.19012 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... § 56.19012 Grooved drums. Where grooved drums are used, the grooves shall be of suitable size and...

  17. 30 CFR 57.19012 - Grooved drums.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Grooved drums. 57.19012 Section 57.19012 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Hoists § 57.19012 Grooved drums. Where grooved drums are used, the grooves shall be of suitable size...

  18. 30 CFR 56.19011 - Drum flanges.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Drum flanges. 56.19011 Section 56.19011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... Drum flanges. Flanges on drums shall extend radially a minimum of 4 inches or three rope...

  19. 30 CFR 57.19012 - Grooved drums.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Grooved drums. 57.19012 Section 57.19012 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Hoists § 57.19012 Grooved drums. Where grooved drums are used, the grooves shall be of suitable size...

  20. 30 CFR 56.19011 - Drum flanges.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Drum flanges. 56.19011 Section 56.19011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... Drum flanges. Flanges on drums shall extend radially a minimum of 4 inches or three rope...

  1. African Drum and Steel Pan Ensembles.

    ERIC Educational Resources Information Center

    Sunkett, Mark E.

    2000-01-01

    Discusses how to develop both African drum and steel pan ensembles providing information on teacher preparation, instrument choice, beginning the ensemble, and lesson planning. Includes additional information for the drum ensembles. Lists references and instructional materials, sources of drums and pans, and common note layout/range for steel pan…

  2. Nuclear waste calorimeter for very large drums with 385 litres sample volume

    SciTech Connect

    Jossens, G.; Mathonat, C.; Bachelet, F.

    2015-03-15

    Calorimetry is a very precise and well adapted tool for the classification of drums containing nuclear waste material depending on their level of activities (low, medium, high). A new calorimeter has been developed by SETARAM Instrumentation and the CEA Valduc in France. This new calorimeter is designed for drums having a volume bigger than 100 liters. It guarantees high operator safety by optimizing drum handling and air circulation for cooling, and optimized software for direct measurement of the quantity of nuclear material. The LVC1380 calorimeter makes it possible to work over the range 10 to 3000 mW, which corresponds to approximately 0.03 to 10 g of tritium or 3 to 955 g of {sup 241}Pu in a volume up to 385 liters. This calorimeter is based on the heat flow measurement using Peltier elements which surround the drum in the 3 dimensions and therefore measure all the heat coming from the radioactive stuff whatever its position inside the drum. Calorimeter's insulating layers constitute a thermal barrier designed to filter disturbances until they represent less than 0.001 Celsius degrees and to eliminate long term disturbances associated, for example, with laboratory temperature variations between day and night. A calibration device based on Joule effect has also been designed. Measurement time has been optimized but remains long compared with other methods of measurement such as gamma spectrometry but its main asset is to have a good accuracy for low level activities.

  3. Elevated drum testing Phase 1 test plan

    SciTech Connect

    McBeath, R.S.; Meeuwsen, P.V.

    1994-09-01

    An important part of the Hanford environmental mission is the packaging, transportation, and storage of solid radioactive wastes in metal drums. Presently storage drums are placed four to a wooden pallet with the drums banded to each other. Palletized drums are stacked three units high in pre-engineered steel structures in the 200 Area of the Hanford site. Permitted storage space is expensive to construct, maintain, and operate. Storage capacity is increased if additional drum can be stacked within existing facilities and a cost savings over new construction realized. The purpose of this plan is to outline the testing required to provide the safety criteria for elevated (i.e., tiers of four high) drum storage. The major safety concern with elevated drum storage is the danger of a significant fire in the storage facility. The major fire load within the storage facilities is combustible material contained in the drums. If a seismic event, fork lift accident, or other credible incident were to cause drum failure or lid separation, combustible material could be available for fuel. To increase the initial burn in the facilities, the drums must spill their combustible contents, making them free for ignition. If it can be shown that there is not sufficient damage to the drums to allow for release of their solid contents, then the data used for safety documentation will be re-examined. Preliminary tests conducted in the configurations detailed in this test plan have shown that drums maintain their integrity; that is the drum covers remain attached and the drums do not breach. These tests will be conducted by Westinghouse Hanford Company, Equipment Development organization, who is the designated DOE Center of Excellence to conduct drop tests for Department of Transportation (DOT) certification of DOE designed packages and containers.

  4. Considerations for an active and passive scanner to assay nuclear waste drums

    SciTech Connect

    Martz, H.E.; Azevedo, S.G.; Roberson, G.P.; Schneberk, D.J.; Koenig, Z.M.; Camp, D.C. )

    1990-06-08

    Radioactive wastes are generated at many DOE laboratories, military facilities, fuel fabrication and enrichment plants, reactors, hospitals, and university research facilities. At all of these sites, wastes must be separated, packaged, categorized, and packed into some sort of container--usually 208-L (55-gal) drums--for shipment to waste-storage sites. Prior to shipment, the containers must be labeled, assayed, and certified; the assay value determines the ultimate disposition of the waste containers. An accurate nondestructive assay (NDA) method would identify all the radioisotopes present and provide a quantitative measurement of their activity in the drum. In this way, waste containers could be routed in the most cost-effective manner and without having to reopen them. Currently, the most common gamma-ray method used to assay nuclear waste drums is segmented gamma-ray scanning (SGS) spectrometer that crudely measures only the amount of {sup 235}U or {sup 239}Pu present in the drum. This method uses a spatially-averaged, integrated, emitted gamma-ray-intensity value. The emitted intensity value is corrected by an assumed constant-attenuation value determined by a spatially-averaged, transmission (or active) measurement. Unfortunately, this typically results in an inaccurate determination of the radioactive activities within a waste drum because this measurement technique is valid only for homogeneous-attenuation or known drum matrices. However, since homogeneous-attenuation matrices are not common and may be unknown, other NDA techniques based on active and Passive CT (A PCT) are under development. The active measurement (ACT) yields a better attenuation matrix for the drum, while the passive measurement (PCT) more accurately determines the identity of the radioisotopes present and their activities. 9 refs., 2 figs.

  5. Application of PSA to storage of Pu at SRS

    SciTech Connect

    Lux, C.R.

    1995-12-01

    Pu is stored in a wide variety of physical forms and containers at the Savannah River Site (SRS). Probabilistic Safety Analysis (PSA) techniques are used to determine the risk associated with each of these storage modes and assist in identification of the controls necessary to minimize the risk. One storage method involves solids in exposed drum storage where the drums are vulnerable to external events, natural phenomena, and release of material due to weathering of the containers. Another storage method may involve liquids being processed inside the canyon facilities where the greatest risks are not from external events but from process upsets. PSA techniques have been particularly useful in the evaluation of criticality situations concerning Pu processing and storage. The applications include ``normal`` operating situations, problems following a seismic event, and the identification of potential problems during the decontamination and decommissioning of a facility. In this paper I would like to discuss two specific examples of the use of PSA techniques. The first involves the analysis of potential accidents in a Pu receipt and storage facility. The second example involves processing solutions that have the potential for experiencing an uncontrolled ``red oil`` reaction.

  6. Anaerobic Biotransformation and Mobility of Pu and Pu-EDTA

    SciTech Connect

    Bolton, H., Jr.; Bailey, V.L.; Plymale, A.E.; Rai, D.; Xun, L.

    2006-04-05

    The complexation of radionuclides (e.g., plutonium (Pu) and {sup 60}Co) by co-disposed ethylenediaminetetraacetate (EDTA) has enhanced their transport in sediments at DOE sites. Pu(IV)-EDTA is not stable in the presence of relatively soluble Fe(III) compounds. Since most DOE sites have Fe(III) containing sediments, Pu(IV) is likely not the mobile form of Pu-EDTA. The only other Pu-EDTA complex stable in groundwater relevant to DOE sites would be Pu(III)-EDTA, which only forms under anaerobic conditions. Research is therefore needed to investigate the biotransformation of Pu and Pu-EDTA under anaerobic conditions and the anaerobic biodegradation of Pu-EDTA. The biotransformation of Pu and Pu-EDTA under various anaerobic regimes is poorly understood including the reduction kinetics of Pu(IV) to Pu(III) from soluble (Pu(IV)-EDTA) and insoluble Pu(IV), the redox conditions required for this reduction, the strength of the Pu(III)-EDTA, how the Pu(III)-EDTA competes with other dominant anoxic soluble metals (e.g., Fe(II)), and the oxidation kinetics of Pu(III)-EDTA. Finally, soluble Pu(III)-EDTA under anaerobic conditions would require anaerobic degradation of the EDTA to limit Pu(III) transport. Anaerobic EDTA degrading microorganisms have never been isolated. Recent results have shown that Shewanella oneidensis MR-1, a dissimilatory metal reducing bacterium, can reduce Pu(IV) to Pu(III). The Pu(IV) was provided as insoluble PuO2. The highest rate of Pu(IV) reduction was with the addition of AQDS, an electron shuttle. Of the total amount of Pu solubilized (i.e., soluble through a 0.36 nm filter), approximately 70% was Pu(III). The amount of soluble Pu was between 4.8 and 3.2 micromolar at day 1 and 6, respectively, indicating rapid reduction. The micromolar Pu is significant since the drinking water limit for Pu is 10{sup -12} M. On-going experiments are investigating the influence of EDTA on the rate of Pu reduction and the stability of the formed Pu(III). We have also

  7. Anaerobic Biotransformation and Mobility of Pu and Pu-EDTA

    SciTech Connect

    Bolton, H., Jr.; Rai, D.; Xun, L.

    2005-04-18

    The complexation of radionuclides (e.g., plutonium (Pu) and {sup 60}Co) by codisposed ethylenediaminetetraacetate (EDTA) has enhanced their transport in sediments at DOE sites. Our previous NABIR research investigated the aerobic biodegradation and biogeochemistry of Pu(IV)-EDTA. Plutonium(IV) forms stable complexes with EDTA under aerobic conditions and an aerobic EDTA degrading bacterium can degrade EDTA in the presence of Pu and decrease Pu mobility. However, our recent studies indicate that while Pu(IV)-EDTA is stable in simple aqueous systems, it is not stable in the presence of relatively soluble Fe(III) compounds (i.e., Fe(OH){sub 3}(s)--2-line ferrihydrite). Since most DOE sites have Fe(III) containing sediments, Pu(IV) in likely not the mobile form of Pu-EDTA in groundwater. The only other Pu-EDTA complex stable in groundwater relevant to DOE sites would be Pu(III)-EDTA, which only forms under anaerobic conditions. Research is therefore needed in this brand new project to investigate the biotransformation of Pu and Pu-EDTA under anaerobic conditions. The biotransformation of Pu and Pu-EDTA under various anaerobic regimes is poorly understood including the reduction kinetics of Pu(IV) to Pu(III) from soluble (Pu(IV)-EDTA) and insoluble Pu(IV) as PuO2(am) by metal reducing bacteria, the redox conditions required for this reduction, the strength of the Pu(III)-EDTA complex, how the Pu(III)-EDTA complex competes with other dominant anoxic soluble metals (e.g., Fe(II)), and the oxidation kinetics of Pu(III)-EDTA. Finally, the formation of a stable soluble Pu(III)-EDTA complex under anaerobic conditions would require degradation of the EDTA complex to limit Pu(III) transport in geologic environments. Anaerobic EDTA degrading microorganisms have not been isolated. These knowledge gaps preclude the development of a mechanistic understanding of how anaerobic conditions will influence Pu and Pu-EDTA fate and transport to assess, model, and design approaches to stop

  8. Pu(V) and Pu(IV) sorption to montmorillonite.

    PubMed

    Begg, James D; Zavarin, Mavrik; Zhao, Pihong; Tumey, Scott J; Powell, Brian; Kersting, Annie B

    2013-05-21

    Plutonium (Pu) adsorption to and desorption from mineral phases plays a key role in controlling the environmental mobility of Pu. Here we assess whether the adsorption behavior of Pu at concentrations used in typical laboratory studies (≥10(-10) [Pu] ≤ 10(-6) M) are representative of adsorption behavior at concentrations measured in natural subsurface waters (generally <10(-12) M). Pu(V) sorption to Na-montmorillonite was examined over a wide range of initial Pu concentrations (10(-6)-10(-16) M). Pu(V) adsorption after 30 days was linear over the wide range of concentrations studied, indicating that Pu sorption behavior from laboratory studies at higher concentrations can be extrapolated to sorption behavior at low, environmentally relevant concentrations. Pu(IV) sorption to montmorillonite was studied at initial concentrations of 10(-6)-10(-11) M and was much faster than Pu(V) sorption over the 30 day equilibration period. However, after one year of equilibration, the extent of Pu(V) adsorption was similar to that observed for Pu(IV) after 30 days. The continued uptake of Pu(V) is attributed to a slow, surface-mediated reduction of Pu(V) to Pu(IV). Comparison between rates of adsorption of Pu(V) to montmorillonite and a range of other minerals (hematite, goethite, magnetite, groutite, corundum, diaspore, and quartz) found that minerals containing significant Fe and Mn (hematite, goethite, magnetite, and groutite) adsorbed Pu(V) faster than those which did not, highlighting the potential importance of minerals with redox couples in increasing the rate of Pu(V) removal from solution. PMID:23614502

  9. Hot air drum evaporator. [Patent application

    DOEpatents

    Black, R.L.

    1980-11-12

    An evaporation system for aqueous radioactive waste uses standard 30 and 55 gallon drums. Waste solutions form cascading water sprays as they pass over a number of trays arranged in a vertical stack within a drum. Hot dry air is circulated radially of the drum through the water sprays thereby removing water vapor. The system is encased in concrete to prevent exposure to radioactivity. The use of standard 30 and 55 gallon drums permits an inexpensive compact modular design that is readily disposable, thus eliminating maintenance and radiation build-up problems encountered with conventional evaporation systems.

  10. Biotransformation of PuEDTA: Implications to Pu Immobilization

    SciTech Connect

    Bolton, Harvey, Jr.

    2006-06-01

    This project integrates three distinct goals to develop a fundamental understanding of the potential fate and disposition of plutonium in sediments that are co-contaminated with EDTA. The three objectives are: (1) Develop thermodynamic data for Pu-EDTA species and determine the dominant mobile form of Pu under anaerobic conditions. (2) Elucidate the mechanism and rates of Pu(IV) and Pu(IV)-EDTA reduction by metal-reducing bacteria and determine where the Pu is located (in solution, biosorbed, bioaccumulated). (3) Enrich and isolate anaerobic EDTA-degrading microorganisms to investigate the anaerobic biodegradation of Pu-EDTA.

  11. 13. Detail view of drum screen short shaft gears, journal ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    13. Detail view of drum screen short shaft gears, journal bearing, rotation drive chain, upper sprocket gear, and drum screen edge in background, facing southeast (downstream) from drum screen cover. - Congdon Canal, Fish Screen, Naches River, Yakima, Yakima County, WA

  12. Pu-239 and Pu-240 inventories and Pu-240/ Pu-239 atom ratios in the water column off Sanriku, Japan.

    NASA Astrophysics Data System (ADS)

    Yamada, Masatoshi; Zheng, Jian; Aono, Tatsuo

    2013-04-01

    A magnitude 9.0 earthquake and subsequent tsunami occurred in the Pacific Ocean off northern Honshu, Japan, on 11 March 2011 which caused severe damage to the Fukushima Dai-ichi Nuclear Power Plant. This accident has resulted in a substantial release of radioactive materials to the atmosphere and ocean, and has caused extensive contamination of the environment. However, no information is available on the amounts of radionuclides such as Pu isotopes released into the ocean at this time. Investigating the background baseline concentration and atom ratio of Pu isotopes in seawater is important for assessment of the possible contamination in the marine environment. Pu-239 (half-life: 24,100 years), Pu-240 (half-life: 6,560 years) and Pu-241 (half-life: 14.325 years) mainly have been released into the environment as the result of atmospheric nuclear weapons testing. The atom ratio of Pu-240/Pu-239 is a powerful fingerprint to identify the sources of Pu in the ocean. The Pu-239 and Pu-240 inventories and Pu-240/Pu-239 atom ratios in seawater samples collected in the western North Pacific off Sanriku before the accident at Fukushima Dai-ichi Nuclear Power Plant will provide useful background baseline data for understanding the process controlling Pu transport and for distinguishing additional Pu sources. Seawater samples were collected with acoustically triggered quadruple PVC sampling bottles during the KH-98-3 cruise of the R/V Hakuho-Maru. The Pu-240/Pu-239 atom ratios were measured with a double-focusing SF-ICP-MS, which was equipped with a guard electrode to eliminate secondary discharge in the plasma and to enhance overall sensitivity. The Pu-239 and Pu-240 concentrations were 2.07 and 1.67 mBq/m3 in the surface water, respectively, and increased with depth; a subsurface maximum was identified at 750 m depth, and the concentrations decreased with depth, then increased at the bottom layer. The total Pu-239+240 inventory in the entire water column (depth interval 0

  13. Fort Drum integrated resource assessment

    SciTech Connect

    Dixon, D.R.; Armstrong, P.R.; Brodrick, J.R.; Daellenbach, K.K.; Di Massa, F.V.; Keller, J.M.; Richman, E.E.; Sullivan, G.P.; Wahlstrom, R.R.

    1992-12-01

    The US Army Forces Command (FORSCOM) has tasked the Pacific Northwest Laboratory (PNL) as the lead laboratory supporting the US Department of Energy (DOE) Federal Energy Management Program's mission to identify, evaluate, and assist in acquiring all cost-effective energy projects at Fort Drum. This is a model program PNL is designing for federal customers served by the Niagara Mohawk Power Company. It will identify and evaluate all electric and fossil fuel cost-effective energy projects; develop a schedule at each installation for project acquisition considering project type, size, timing, and capital requirements, as well as energy and dollar savings; and secure 100% of the financing required to implement electric energy efficiency projects from Niagara Mohawk and have Niagara Mohawk procure the necessary contractors to perform detailed audits and install the technologies. This report documents the assessment of baseline energy use at one of Niagara Mohawk's primary federal facilities, the FORSCOM Fort Drum facility located near Watertown, New York. It is a companion report to Volume 1, the Executive Summary, and Volume 3, the Resource Assessment. This analysis examines the characteristics of electric, gas, oil, propane, coal, and purchased thermal capacity use for fiscal year (FY) 1990. It records energy-use intensities for the facilities at Fort Drum by building type and energy end use. It also breaks down building energy consumption by fuel type, energy end use, and building type. A complete energy consumption reconciliation is presented that includes the accounting of all energy use among buildings, utilities, central systems, and applicable losses.

  14. Drum plug piercing and sampling device and method

    DOEpatents

    Counts, Kevin T.

    2011-04-26

    An apparatus and method for piercing a drum plug of a drum in order to sample and/or vent gases that may accumulate in a space of the drum is provided. The drum is not damaged and can be reused since the pierced drum plug can be subsequently replaced. The apparatus includes a frame that is configured for engagement with the drum. A cylinder actuated by a fluid is mounted to the frame. A piercer is placed into communication with the cylinder so that actuation of the cylinder causes the piercer to move in a linear direction so that the piercer may puncture the drum plug of the drum.

  15. A NOVEL APPROACH TO DRUM VENTING AND DRUM MONITORINGe/pj

    SciTech Connect

    Ohl, P.C.; Farwick, C.C.; Douglas, D.G.; Cruz, E.J.

    2003-02-27

    This paper describes the details and specifications associated with drum venting and drum monitoring technologies, and discusses the maturity of in-place systems and current applications. Each year, unventilated drums pressurize and develop bulges and/or breaches that can result in potentially hazardous explosions, posing undesirable hazards to workers and the environment. Drum venting is accomplished by the safe and simple installation of ventilated lids at the time of packaging, or by the inherently risky in-situ ventilation (depressurization) of ''bulged'' drums. Drum monitoring employs either a Magnetically Coupled Pressure Gauge (MCPG) Patent Pending and/or a Magnetically Coupled Corrosion Gauge (MCCG) Patent Pending. Through patented magnetic sensor coupling, these devices enable the noninvasive and remote monitoring of the potentially hazardous materials and/or spent nuclear fuel that is contained in 55-gal drums and associated steel overpack containers.

  16. One-trip drum operating instruction

    SciTech Connect

    Ruff, D.T.

    1994-10-01

    The one trip system is a bagless transfer system for egress of waste from gloveboxes into 55 gallon one-trip drums. The contents of this document give an overview of the assembly, loading, and handling of the one-trip drum for use in the WRAP-1 plant.

  17. Ellie Mannette: Master of the Steel Drum.

    ERIC Educational Resources Information Center

    Svaline, J. Marc

    2001-01-01

    Presents an interview with Elliot ("Ellie") Mannette who has played a major role in the development and application of steel drums. States that he has spent most of his life designing and teaching the steel drums. Covers interview topics and background information on Mannette. (CMK)

  18. Drum Circles and the National Standards

    ERIC Educational Resources Information Center

    Fidyk, Steve

    2009-01-01

    The beauty of hand drums is that a child of nearly any age can grab one and get a sound. So how can classroom teachers incorporate this enjoyable activity into something that's actually educational? For young students especially, a drum circle can be liberating. Children can be given various responsibilities--as participants, circle organizers,…

  19. Los Alamos waste drum shufflers users manual

    SciTech Connect

    Rinard, P.M.; Adams, E.L.; Painter, J.

    1993-08-24

    This user manual describes the Los Alamos waste drum shufflers. The primary purpose of the instruments is to assay the mass of {sup 235}U (or other fissile materials) in drums of assorted waste. It can perform passive assays for isotopes that spontaneously emit neutrons or active assays using the shuffler technique as described on this manual.

  20. Environmental policy -- A leaking drum?

    SciTech Connect

    Bishop, J.

    1995-07-01

    Twenty years ago, the US had virtually no overall environmental policy. Since then, one has evolved as a result of accumulated legislation, much of which was crafted in reaction to specific events, typically real or potential disasters. The familiar names of Love Canal, Times Beach, Bhopal and others are the symbolic anchor points of that evolution, which yielded Superfund, the Resource Conservation and Recovery Act, the Superfund Amendments and Reauthorization Act, and other environmental statutes. The laws in each case were developed in response to particular environmental and health issues--clean water for drinking and recreation, unpolluted air, safe production of chemicals and chemical-based products. The result was a growing body of environmental legislation that eventually became an accumulate of requirements lacking internal consistency or coherence. Because policymaking followed, rather than guided, legislative actions, the policy itself became inconsistent and sometimes illogical. Like a drum that gradually and indiscriminately is filled with a mixture of mutually reactive chemicals, environmental policy increasingly became a volatile source of concern for those industries in whose midst it had been placed. Lately, there is growing consensus that the drum not only has been overfilled, it also is leaking.

  1. Fort Drum integrated resource assessment

    SciTech Connect

    Dixon, D.R.; Armstrong, P.R.; Daellenbach, K.K.; Dagle, J.E.; Di Massa, F.V.; Elliott, D.B.; Keller, J.M.; Richman, E.E.; Shankle, S.A.; Sullivan, G.P.; Wahlstrom, R.R.

    1992-12-01

    The US Army Forces Command (FORSCOM) has tasked Pacific Northwest Laboratory (PNL) as the lead laboratory supporting the US Department of Energy (DOE) Federal Energy Management Program's (FEMP) mission to identify, evaluate, and assist in acquiring all cost-effective energy projects at Fort Drum. This is a model program PNL is designing for federal customers served by the Niagara Mohawk Power Company (Niagara Mohawk). It will (1) identify and evaluate all electric and fossil fuel cost-effective energy projects; (2) develop a schedule at each installation for project acquisition considering project type, size, timing, capital requirements, as well as energy and dollar savings; and (3) secure 100% of the financing required to implement electric energy efficiency projects from Niagara Mohawk and have Niagara Mohawk procure the necessary contractors to perform detailed audits and install the technologies. This report provides the results of the fossil fuel and electric energy resource opportunity (ERO) assessments performed by PNL at one of Niagara Mohawk's primary federal facilities, the FORSCOM Fort Drum facility located near Watertown, New York. It is a companion report to Volume 1, the Executive Summary, and Volume 2, the Baseline Detail.

  2. Simultaneous Thermal Analysis of WIPP and LANL Waste Drum Samples: A Preliminary Report

    SciTech Connect

    Wayne, David M.

    2015-10-19

    On Friday, February 14, 2014, an incident in P7R7 of the WIPP underground repository released radioactive material into the environment. The direct cause of the event was a breached transuranic (TRU) waste container, subsequently identified as Drum 68660. Photographic and other evidence indicates that the breach of 68660 was caused by an exothermic event. Subsequent investigations (Britt, 2015; Clark and Funk, 2015; Wilson et al., 2015; Clark, 2015) indicate that the combination of nitrate salts, pH neutralizing chemicals, and organic-based adsorbent represented a potentially energetic mixture. The materials inside the breached steel drum consisted of remediated, 30- to 40-year old, Pu processing wastes from LANL. The contents were processed and repackaged in 2014. Processing activities at LANL included: 1) neutralization of acidic liquid contents, 2) sorption of the neutralized liquid, and 3) mixing of acidic nitrate salts with an absorber to meet waste acceptance criteria. The contents of 68660 and its sibling, 68685, were derived from the same parent drum, S855793. Drum S855793 originally contained ten plastic bags of acidic nitrate salts, and four bags of mixed nitrate and oxalate salts generated in 1985 by Pu recovery operations. These salts were predominantly oxalic acid, hydrated nitrate salts of Mg, Ca, and Fe, anhydrous Na(NO3), and minor amounts of anhydrous and hydrous nitrate salts of Pb, Al, K, Cr, and Ni. Other major components include sorbed water, nitric acid, dissolved nitrates, an absorbent (Swheat Scoop®) and a neutralizer (KolorSafe®). The contents of 68660 are described in greater detail in Appendix E of Wilson et al. (2015)

  3. FIFTY-FIVE GALLON DRUM STANDARD STUDY

    SciTech Connect

    PUIGH RJ

    2009-05-14

    Fifty-five gallon drums are routinely used within the U.S. for the storage and eventual disposal of fissionable materials as Transuranic or low-level waste. To support these operations, criticality safety evaluations are required. A questionnaire was developed and sent to selected Endusers at Hanford, Idaho National Laboratory, Lawrence Livermore National Laboratory, Oak Ridge and the Savannah River Site to solicit current practices. This questionnaire was used to gather information on the kinds of fissionable materials packaged into drums, the models used in performing criticality safety evaluations in support of operations involving these drums, and the limits and controls established for the handling and storage of these drums. The completed questionnaires were reviewed and clarifications solicited through individual communications with each Enduser to obtain more complete and consistent responses. All five sites have similar drum operations involving thousands to tens of thousands of fissionable material waste drums. The primary sources for these drums are legacy (prior operations) and decontamination and decommissioning wastes at all sites except Lawrence Livermore National Laboratory. The results from this survey and our review are discussed in this paper.

  4. Energy expenditure in rock/pop drumming.

    PubMed

    De La Rue, S E; Draper, S B; Potter, C R; Smith, M S

    2013-10-01

    Despite the vigorous nature of rock/pop drumming, there are no precise data on the energy expenditure of this activity. The aim of this study was to quantify the energy cost of rock/pop drumming. Fourteen male drummers (mean±SD; age 27±8 yrs.) completed an incremental drumming test to establish the relationship between energy expenditure and heart rate for this activity and a ramped cycle ergometer test to exhaustion as a criterion measure for peak values (oxygen uptake and heart rate). During live concert performance heart rate was continuously measured and used to estimate energy expenditure (from the energy expenditure vs. heart rate data derived from the drumming test). During concert performance, estimated energy expenditure (mean±SD) was 623±168 kcal.h⁻¹ (8.1±2.2 METs) during performances of 38.6±15.6 min, and drummers achieved a peak heart rate of 186±16 b.min⁻¹. During the drumming test participants attained 78.7±8.3% of the cycle ergometer peak oxygen uptake. Rock/pop drumming represents a relatively high-intensity form of physical activity and as such involves significant energy expenditure. Rock/pop drumming should be considered as a viable alternative to more traditional forms of physical activity.

  5. Modeling VOC transport in simulated waste drums

    SciTech Connect

    Liekhus, K.J.; Gresham, G.L.; Peterson, E.S.; Rae, C.; Hotz, N.J.; Connolly, M.J.

    1993-06-01

    A volatile organic compound (VOC) transport model has been developed to describe unsteady-state VOC permeation and diffusion within a waste drum. Model equations account for three primary mechanisms for VOC transport from a void volume within the drum. These mechanisms are VOC permeation across a polymer boundary, VOC diffusion across an opening in a volume boundary, and VOC solubilization in a polymer boundary. A series of lab-scale experiments was performed in which the VOC concentration was measured in simulated waste drums under different conditions. A lab-scale simulated waste drum consisted of a sized-down 55-gal metal drum containing a modified rigid polyethylene drum liner. Four polyethylene bags were sealed inside a large polyethylene bag, supported by a wire cage, and placed inside the drum liner. The small bags were filled with VOC-air gas mixture and the VOC concentration was measured throughout the drum over a period of time. Test variables included the type of VOC-air gas mixtures introduced into the small bags, the small bag closure type, and the presence or absence of a variable external heat source. Model results were calculated for those trials where the VOC permeability had been measured. Permeabilities for five VOCs [methylene chloride, 1,1,2-trichloro-1,2,2-trifluoroethane (Freon-113), 1,1,1-trichloroethane, carbon tetrachloride, and trichloroethylene] were measured across a polyethylene bag. Comparison of model and experimental results of VOC concentration as a function of time indicate that model accurately accounts for significant VOC transport mechanisms in a lab-scale waste drum.

  6. TRU drum corrosion task team report

    SciTech Connect

    Kooda, K.E.; Lavery, C.A.; Zeek, D.P.

    1996-05-01

    During routine inspections in March 1996, transuranic (TRU) waste drums stored at the Radioactive Waste Management Complex (RWMC) were found with pinholes and leaking fluid. These drums were overpacked, and further inspection discovered over 200 drums with similar corrosion. A task team was assigned to investigate the problem with four specific objectives: to identify any other drums in RWMC TRU storage with pinhole corrosion; to evaluate the adequacy of the RWMC inspection process; to determine the precise mechanism(s) generating the pinhole drum corrosion; and to assess the implications of this event for WIPP certifiability of waste drums. The task team investigations analyzed the source of the pinholes to be Hcl-induced localized pitting corrosion. Hcl formation is directly related to the polychlorinated hydrocarbon volatile organic compounds (VOCs) in the waste. Most of the drums showing pinhole corrosion are from Content Code-003 (CC-003) because they contain the highest amounts of polychlorinated VOCs as determined by headspace gas analysis. CC-001 drums represent the only other content code with a significant number of pinhole corrosion drums because their headspace gas VOC content, although significantly less than CC-003, is far greater than that of the other content codes. The exact mechanisms of Hcl formation could not be determined, but radiolytic and reductive dechlorination and direct reduction of halocarbons were analyzed as the likely operable reactions. The team considered the entire range of feasible options, ranked and prioritized the alternatives, and recommended the optimal solution that maximizes protection of worker and public safety while minimizing impacts on RWMC and TRU program operations.

  7. 49 CFR 178.505 - Standards for aluminum drums.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Standards for aluminum drums. 178.505 Section 178...-bulk Performance-Oriented Packaging Standards § 178.505 Standards for aluminum drums. (a) The following are the identification codes for aluminum drums: (1) 1B1 for a non-removable head aluminum drum;...

  8. 49 CFR 178.505 - Standards for aluminum drums.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Standards for aluminum drums. 178.505 Section 178...-bulk Performance-Oriented Packaging Standards § 178.505 Standards for aluminum drums. (a) The following are the identification codes for aluminum drums: (1) 1B1 for a non-removable head aluminum drum;...

  9. 49 CFR 178.505 - Standards for aluminum drums.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Standards for aluminum drums. 178.505 Section 178...-bulk Performance-Oriented Packaging Standards § 178.505 Standards for aluminum drums. (a) The following are the identification codes for aluminum drums: (1) 1B1 for a non-removable head aluminum drum;...

  10. 49 CFR 178.505 - Standards for aluminum drums.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Standards for aluminum drums. 178.505 Section 178...-bulk Performance-Oriented Packaging Standards § 178.505 Standards for aluminum drums. (a) The following are the identification codes for aluminum drums: (1) 1B1 for a non-removable head aluminum drum;...

  11. 52. EXTERIOR DETAIL VIEW OF A SPARE DRUM FOR A ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    52. EXTERIOR DETAIL VIEW OF A SPARE DRUM FOR A FRENIER PUMP. THE CHARCOAL HOUSE IS IN THE BACKGROUND AND THE DRUM LEANING AGAINST THE EAST SIDE OF THE MILL ANNEX. NOTE THE WELDS IN THE DRUM, THEY DELINEATE THE SPIRAL LEADING TO THE CENTER OF THE DRUM. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

  12. 30 CFR 56.19026 - Drum end attachment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drum end attachment. 56.19026 Section 56.19026... Ropes § 56.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1... bolts, clamps, or wedges, provided that the attachment is a design feature of the hoist drum....

  13. 30 CFR 57.19026 - Drum end attachment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drum end attachment. 57.19026 Section 57.19026... Wire Ropes § 57.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1... bolts, clamps, or wedges, provided that the attachment is a design feature of the hoist drum....

  14. 30 CFR 57.19026 - Drum end attachment.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Drum end attachment. 57.19026 Section 57.19026... Wire Ropes § 57.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one full turn around the drum spoke; (2) Securely by clips after making...

  15. 49 CFR 178.507 - Standards for plywood drums.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Standards for plywood drums. 178.507 Section 178...-bulk Performance-Oriented Packaging Standards § 178.507 Standards for plywood drums. (a) The identification code for a plywood drum is 1D. (b) Construction requirements for plywood drums are as follows:...

  16. 30 CFR 56.19026 - Drum end attachment.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Drum end attachment. 56.19026 Section 56.19026... Ropes § 56.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one full turn around the drum spoke; (2) Securely by clips after making...

  17. 30 CFR 77.1436 - Drum end attachment.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Drum end attachment. 77.1436 Section 77.1436... Hoisting Wire Ropes § 77.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one full turn around the drum spoke; (2) Securely by clips...

  18. 30 CFR 56.19026 - Drum end attachment.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Drum end attachment. 56.19026 Section 56.19026... Ropes § 56.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one full turn around the drum spoke; (2) Securely by clips after making...

  19. 30 CFR 77.1436 - Drum end attachment.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Drum end attachment. 77.1436 Section 77.1436... Hoisting Wire Ropes § 77.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one full turn around the drum spoke; (2) Securely by clips...

  20. 30 CFR 57.19026 - Drum end attachment.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Drum end attachment. 57.19026 Section 57.19026... Wire Ropes § 57.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one full turn around the drum spoke; (2) Securely by clips after making...

  1. 30 CFR 57.19026 - Drum end attachment.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Drum end attachment. 57.19026 Section 57.19026... Wire Ropes § 57.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one full turn around the drum spoke; (2) Securely by clips after making...

  2. 49 CFR 178.507 - Standards for plywood drums.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Standards for plywood drums. 178.507 Section 178...-bulk Performance-Oriented Packaging Standards § 178.507 Standards for plywood drums. (a) The identification code for a plywood drum is 1D. (b) Construction requirements for plywood drums are as follows:...

  3. 30 CFR 56.19026 - Drum end attachment.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Drum end attachment. 56.19026 Section 56.19026... Ropes § 56.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one full turn around the drum spoke; (2) Securely by clips after making...

  4. 30 CFR 56.19026 - Drum end attachment.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Drum end attachment. 56.19026 Section 56.19026... Ropes § 56.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one full turn around the drum spoke; (2) Securely by clips after making...

  5. 30 CFR 57.19026 - Drum end attachment.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Drum end attachment. 57.19026 Section 57.19026... Wire Ropes § 57.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one full turn around the drum spoke; (2) Securely by clips after making...

  6. 49 CFR 178.507 - Standards for plywood drums.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Standards for plywood drums. 178.507 Section 178...-bulk Performance-Oriented Packaging Standards § 178.507 Standards for plywood drums. (a) The identification code for a plywood drum is 1D. (b) Construction requirements for plywood drums are as follows:...

  7. 30 CFR 77.1436 - Drum end attachment.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Drum end attachment. 77.1436 Section 77.1436... Hoisting Wire Ropes § 77.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one full turn around the drum spoke; (2) Securely by clips...

  8. 30 CFR 77.1436 - Drum end attachment.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Drum end attachment. 77.1436 Section 77.1436... Hoisting Wire Ropes § 77.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one full turn around the drum spoke; (2) Securely by clips...

  9. 49 CFR 178.507 - Standards for plywood drums.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Standards for plywood drums. 178.507 Section 178...-bulk Performance-Oriented Packaging Standards § 178.507 Standards for plywood drums. (a) The identification code for a plywood drum is 1D. (b) Construction requirements for plywood drums are as follows:...

  10. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Standards for steel drums. 178.504 Section 178.504...-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for a removable...

  11. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Standards for steel drums. 178.504 Section 178.504...-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for a removable...

  12. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Standards for steel drums. 178.504 Section 178.504...-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for a removable...

  13. A Sludge Drum in the APNea System

    SciTech Connect

    Hensley, D.

    1998-11-17

    The assay of sludge drums pushes the APNea System to a definite extreme. Even though it seems clear that neutron based assay should be the method of choice for sludge drums, the difficulties posed by this matrix push any NDA technique to its limits. Special emphasis is given here to the differential die-away technique, which appears to approach the desired sensitivity. A parallel analysis of ethafoam drums will be presented, since the ethafoam matrix fits well within the operating range of the AIWea System, and, having been part of the early PDP trials, has been assayed by many in the NDA community.

  14. Over-Pressurized Drums: Their Causes and Mitigation

    SciTech Connect

    Simmons, Fred; Kuntamukkula, Murty; Quigley, David; Robertson, Janeen; Freshwater, David

    2009-07-10

    Having to contend with bulging or over-pressurized drums is, unfortunately, a common event for people storing chemicals and chemical wastes. (Figure 1) The Department of Energy alone reported over 120 incidents of bulging drums between 1992 and 1999 (1). Bulging drums can be caused by many different mechanisms, represent a number of significant hazards and can be tricky to mitigate. In this article, we will discuss reasons or mechanisms by which drums can become over-pressurized, recognition of the hazards associated with and mitigation of over-pressurized drums, and methods that can be used to prevent drum over-pressurization from ever occurring. Drum pressurization can represent a significant safety hazard. Unless recognized and properly mitigated, improperly manipulated pressurized drums can result in employee exposure, employee injury, and environmental contamination. Therefore, recognition of when a drum is pressurized and knowledge of pressurized drum mitigation techniques is essential.

  15. Interpreting honeycomb climbing-drum peel tests

    NASA Technical Reports Server (NTRS)

    Ferdie, R. D.

    1977-01-01

    Drum-peel tests are made more meaningful by use of approximations to derive analytical expressions relating failures due to bond flatwise tension, inplane tension, and shear, to adhesive weight and method of bond cure.

  16. Estimates for Pu-239 loadings in burial ground culverts based on fast/slow neutron measurements

    SciTech Connect

    Winn, W.G.; Hochel, R.C.; Hofstetter, K.J.; Sigg, R.A.

    1989-08-15

    This report provides guideline estimates for Pu-239 mass loadings in selected burial ground culverts. The relatively high recorded Pu-239 contents of these culverts have been appraised as suspect relative to criticality concerns, because they were assayed only with the solid waste monitor (SWM) per gamma-ray counting. After 1985, subsequent waste was also assayed with the neutron coincidence counter (NCC), and a comparison of the assay methods showed that the NCC generally yielded higher assays than the SWM. These higher NCC readings signaled a need to conduct non-destructive/non-intrusive nuclear interrogations of these culverts, and a technical team conducted scoping measurements to illustrate potential assay methods based on neutron and/or gamma counting. A fast/slow neutron method has been developed to estimate the Pu-239 in the culverts. In addition, loading records include the SWM assays of all Pu-239 cuts of some of the culvert drums and these data are useful in estimating the corresponding NCC drum assays from NCC vs SWM data. Together, these methods yield predictions based on direct measurements and statistical inference.

  17. Formation of Pu amorphous alloys or metastable structures in Pu-Fe, Pu-Ta, and Pu-Si alloys

    SciTech Connect

    Rizzo, H.F.; Echeverria, A.W.

    1985-08-20

    Sputter deposition technique was used to study the possible formation of amorphous structures in Pu-Fe, Pu-Ta, and Pu-Si systems. A triode sputtering system was used to prepare sputtered coatings: 13 to 59 at. % (a/o) Fe, 10 to 50 a/o Si, and 15 to 65 a/o Ta. Structure of the coatings was determined by x-ray diffraction techniques. The temperature stability of the obtained structures was determined by Differential Scanning Calorimetry (DSC) measurements. The Pu-Fe and Pu-Si binary systems showed strong evidence for the formation of amorphous phases in the sputtered coatings. X-ray analyses indicated the presence of Pu6Fe in the 13 to 20 a/o Fe range of Pu-Fe alloys and no apparent crystalline phases over the entire 10 to 50 a/o Si range of Pu-Si alloys. In the Pu-Ta system, the DSC data obtained for compositions below 50 a/o Ta did not show typical crystallization exotherms. At compositions above 50 a/o Ta, a metastable bcc alpha Ta structure was observed with an expanded lattice parameter. The calculated volume expansion (2.9%) corresponds to 29 a/o of Pu in solid solution if the lattice parameter is assumed to follow Vegards Law. After storage in a nitrogen glovebox atmosphere for over two years, the Pu-Si and Pu-Ta coatings have maintained a metallic luster and have shown no visible evidence of surface oxidation.

  18. Cutter drum drive assembly for canted end sections

    SciTech Connect

    Baum, G.L.

    1981-06-02

    A continuous mining machine includes a body portion having a longitudinal axis and mounted on endless tracks. A boom member extends forwardly from the body portion with a cutter drum member rotatably mounted on the front of the boom member. The cutter drum member has an intermediate drum section and a pair of canted end drum section. The intermediate drum section is spaced from the end drum sections to provide openings therebetween. The boom member has front end portions extending through the openings to rotatably support the cutter drum member. Input drive shafts extend from drive motors on the body portion forwardly from the boom member at an acute angle with respect to the longitudinal axis of the body portion through the openings. In each end drum section meshing spiral bevel gears connect the input drive shaft through a planetary gear train to the end drum drive shaft. Rotation is transmitted from each end drum drive shaft to a drive shaft for rotating the intermediate drum section. Positioning the input drive shafts at an angle with respect to the longitudinal axis of the machine body portion facilitates positioning planetary gear trains in the end drum section to locate the cutter drum assembly for efficient feeding of dislodged material onto the machine and reduce the diameter of the intermediate drum section.

  19. Biodegradation of PuEDTA and Impacts on Pu Mobility

    SciTech Connect

    Bolton, H., Jr.; Rai, D.; Xun, L.

    2004-03-17

    The contamination of many DOE sites by Pu presents a long-term problem because of its long half-life (240,000 yrs) and the low drinking water standard (<10{sup -12} M). EDTA was co-disposed with radionuclides (e.g., Pu, {sup 60}Co), formed strong complexes, and enhanced radionuclide transport at several DOE sites. Biodegradation of EDTA should decrease Pu mobility. One objective of this project was to determine the biodegradation of EDTA in the presence of PuEDTA complexes. The aqueous system investigated at pH 7 (10{sup -4} M EDTA and 10{sup -6} M Pu) contained predominantly Pu(OH){sub 2}EDTA{sup 2-}. The EDTA was degraded at a faster rate in the presence of Pu. As the total concentration of both EDTA and PuEDTA decreased (i.e., 10{sup -5} M EDTA and 10{sup -7} M PuEDTA), the presence of Pu decreased the biodegradation rate of the EDTA. It is currently unclear why the concentration of Pu directly affects the increase/decrease in rate of EDTA biodegradation. The soluble Pu concentration decreased, in agreement with thermodynamic predictions, as the EDTA was biodegraded, indicating that biodegradation of EDTA will decrease Pu mobility when the Pu is initially present as Pu(IV)EDTA. A second objective was to investigate how the presence of competing metals, commonly encountered in geologic media, will influence the speciation and biodegradation of Pu(IV)-EDTA. Studies on the solubilities of Fe(OH){sub 3}(s) and of Fe(OH){sub 3}(s) plus PuO{sub 2}(am) in the presence of EDTA and as a function of pH showed that Fe(III) out competes the Pu(IV) for the EDTA complex, thereby showing that Pu(IV) will not form stable complexes with EDTA for enhanced transport of Pu in Fe(III) dominated subsurface systems. A third objective is to investigate the genes and enzymes involved in EDTA biodegradation. BNC1 can use EDTA and another synthetic chelating agent nitrilotriacetate (NTA) as sole carbon and nitrogen sources. The same catabolic enzymes are responsible for both EDTA and NTA

  20. Elastic properties of Pu metal and Pu-Ga alloys

    SciTech Connect

    Soderlind, P; Landa, A; Klepeis, J E; Suzuki, Y; Migliori, A

    2010-01-05

    We present elastic properties, theoretical and experimental, of Pu metal and Pu-Ga ({delta}) alloys together with ab initio equilibrium equation-of-state for these systems. For the theoretical treatment we employ density-functional theory in conjunction with spin-orbit coupling and orbital polarization for the metal and coherent-potential approximation for the alloys. Pu and Pu-Ga alloys are also investigated experimentally using resonant ultrasound spectroscopy. We show that orbital correlations become more important proceeding from {alpha} {yields} {beta} {yields} {gamma} plutonium, thus suggesting increasing f-electron correlation (localization). For the {delta}-Pu-Ga alloys we find a softening with larger Ga content, i.e., atomic volume, bulk modulus, and elastic constants, suggest a weakened chemical bonding with addition of Ga. Our measurements confirm qualitatively the theory but uncertainties remain when comparing the model with experiments.

  1. Elastic properties of Pu metal and Pu-Ga alloys

    NASA Astrophysics Data System (ADS)

    Söderlind, Per; Landa, Alex; Klepeis, J. E.; Suzuki, Y.; Migliori, A.

    2010-06-01

    We present elastic properties, theoretical and experimental, of Pu metal and Pu-Ga (δ) alloys together with ab initio equilibrium equation of state for these systems. For the theoretical treatment we employ density-functional theory in conjunction with spin-orbit coupling and orbital polarization for the metal and coherent-potential approximation for the alloys. Pu and Pu-Ga alloys are also investigated experimentally using resonant ultrasound spectroscopy. We show that orbital correlations become more important proceeding from α→β→γ plutonium, thus suggesting increasing f -electron correlation and a corresponding softening of the elastic moduli. For the δ-Pu-Ga alloys we find a softening with larger Ga content, i.e., atomic volume, bulk modulus, and elastic constants imply a weakened chemical bonding with addition of Ga. Our measurements confirm qualitatively the theory but uncertainties remain when comparing the model with experiments.

  2. Designing Pu600 for Authentication

    SciTech Connect

    White, G

    2008-07-10

    Many recent Non-proliferation and Arms Control software projects include an authentication component. Demonstrating assurance that software and hardware performs as expected without hidden 'back-doors' is crucial to a project's success. In this context, 'authentication' is defined as determining that the system performs only its intended purpose and performs that purpose correctly and reliably over many years. Pu600 is a mature software solution for determining the presence of Pu and the ratio of Pu240 to Pu239 by analyzing the gamma ray spectra in the 600 KeV region. The project's goals are to explore hardware and software technologies which can by applied to Pu600 which ease the authentication of a complete, end-to-end solution. We will discuss alternatives and give the current status of our work.

  3. Calorimetry of low mass Pu239 items

    SciTech Connect

    Cremers, Teresa L; Sampson, Thomas E

    2010-01-01

    Calorimetric assay has the reputation of providing the highest precision and accuracy of all nondestructive assay measurements. Unfortunately, non-destructive assay practitioners and measurement consumers often extend, inappropriately, the high precision and accuracy of calorimetric assay to very low mass items. One purpose of this document is to present more realistic expectations for the random uncertainties associated with calorimetric assay for weapons grade plutonium items with masses of 200 grams or less.

  4. Chimpanzee drumming: a spontaneous performance with characteristics of human musical drumming

    PubMed Central

    Dufour, Valérie; Poulin, Nicolas; Charlotte Curé; Sterck, Elisabeth H. M.

    2015-01-01

    Despite the quintessential role that music plays in human societies by enabling us to release and share emotions with others, traces of its evolutionary origins in other species remain scarce. Drumming like humans whilst producing music is practically unheard of in our most closely related species, the great apes. Although beating on tree roots and body parts does occur in these species, it has, musically speaking, little in common with human drumming. Researchers suggest that for manual beating in great apes to be compared to human drumming, it should at least be structurally even, a necessary quality to elicit entrainment (beat induction in others). Here we report an episode of spontaneous drumming by a captive chimpanzee that approaches the structural and contextual characteristics usually found in musical drumming. This drumming differs from most beating episodes reported in this species by its unusual duration, the lack of any obvious context, and rhythmical properties that include long-lasting and dynamically changing rhythms, but also evenness and leisureliness. This performance is probably the first evidence that our capacity to drum is shared with our closest relatives. PMID:26080900

  5. Chimpanzee drumming: a spontaneous performance with characteristics of human musical drumming.

    PubMed

    Dufour, Valérie; Poulin, Nicolas; Charlotte Curé; Sterck, Elisabeth H M

    2015-01-01

    Despite the quintessential role that music plays in human societies by enabling us to release and share emotions with others, traces of its evolutionary origins in other species remain scarce. Drumming like humans whilst producing music is practically unheard of in our most closely related species, the great apes. Although beating on tree roots and body parts does occur in these species, it has, musically speaking, little in common with human drumming. Researchers suggest that for manual beating in great apes to be compared to human drumming, it should at least be structurally even, a necessary quality to elicit entrainment (beat induction in others). Here we report an episode of spontaneous drumming by a captive chimpanzee that approaches the structural and contextual characteristics usually found in musical drumming. This drumming differs from most beating episodes reported in this species by its unusual duration, the lack of any obvious context, and rhythmical properties that include long-lasting and dynamically changing rhythms, but also evenness and leisureliness. This performance is probably the first evidence that our capacity to drum is shared with our closest relatives. PMID:26080900

  6. Experimental Avalanches in a Rotating Drum

    NASA Astrophysics Data System (ADS)

    Hubard, Aline; O'Hern, Corey; Shattuck, Mark

    We address the question of universality in granular avalanches and the system size effects on it. We set up an experiment made from a quasi-two-dimensional rotating drum half-filled with a monolayer of stainless-steel spheres. We measure the size of the avalanches created by the increased gravitational stress on the pile as we quasi-statically rotate the drum. We find two kinds of avalanches determined by the drum size. The size and duration distributions of the avalanches that do not span the whole system follow a power law and the avalanche shapes are self-similar and nearly parabolic. The distributions of the avalanches that span the whole system are limited by the maximal amount of potential energy stored in the system at the moment of the avalanche. NSF CMMI-1462439, CMMI-1463455.

  7. 30 CFR 75.1436 - Drum end attachment.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one full turn around the drum spoke; (2) Securely by clips after making one full turn around the shaft,...

  8. 25. View of drum girder, with machinecontrol room above, and ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    25. View of drum girder, with machine-control room above, and drum rollers on center pivot pier. (Nov. 25, 1988) - University Heights Bridge, Spanning Harlem River at 207th Street & West Harlem Road, New York County, NY

  9. 1. UPPER SEGMENT OF SPILLWAY CHANNEL, DRUM GATES ALONG SIDE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. UPPER SEGMENT OF SPILLWAY CHANNEL, DRUM GATES ALONG SIDE OF CHANNEL, LOOKING SOUTH (up the channel) - Tieton Dam, Spillway & Drum Gates, South & East side of State Highway 12, Naches, Yakima County, WA

  10. 6. DETAIL OF THE BRAKE SHOE ON THE EAST DRUM ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    6. DETAIL OF THE BRAKE SHOE ON THE EAST DRUM AT THE STEWARD MINE, LOOKING EAST. THE EAST DRUM WAS UNDER SHOT, THE WEST OVERSHOT - Butte Mineyards, Stewart Mine, Intersection of Main & Woolman Streets, Butte, Silver Bow County, MT

  11. 4. SPILLWAY DRUM GATES AND CHANNEL, LOOKING NORTHEAST (upstream face ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. SPILLWAY DRUM GATES AND CHANNEL, LOOKING NORTHEAST (upstream face and Control House in background) - Tieton Dam, Spillway & Drum Gates, South & East side of State Highway 12, Naches, Yakima County, WA

  12. Tensioning of a belt around a drum using membrane element

    NASA Technical Reports Server (NTRS)

    Chen, C. H. S.

    1980-01-01

    An application of the membrane element to the problem of the tensioning of a conveyer belt which wraps around a drum is presented. Two cases were investigated: (1) belt tension increase due to drum edge wear; and (2) material trapped between the drum and the belt. In both cases it was found that the increase in belt tension was due to the additional stretching of the belt resulting from the drum radius change rather than from the transverse deflection of the belt.

  13. Pu in coastal marine environments

    NASA Astrophysics Data System (ADS)

    Santschi, Peter H.; Li, Yuan-Hui; Bell, Joy J.; Trier, Robert M.; Kawtaluk, Kathy

    1980-12-01

    Analysis of water samples from the New York Bight area and Narragansett Bay reveals that a small fraction of the total Pu (probably Pu (III + IV) species) is continuously removed to the sediments at a rate similar to that of the particle-reactive isotope 228Th. A more "soluble" Pu species appears to be released at times from the sediments to the water column in these nearshore regions. Sediments in shallow areas of the New York Bight south of Rhode Island and Narragansett Bay have high Pu inventories and relatively deep penetration of this element, although the net sediment accumulation rate is generally low (<0.03 g/cm 2 yr). The high Pu inventories can be explained if both sediment resuspension and sediment mixing are assumed to be the major controlling factors for the effective transfer of Pu from the water column to the sediments. By simultaneous modelling of the depth distribution of three tracers which operate on vastly different time scales: 234Th (half-life 24 days), 210Pb (half-life 22 years) and 239,240Pu (introduced into the environment during the past 30 years), bioturbation rates ranging from 4 to 32 cm 2/yr in the surface mixed layer (5-10 cm thick) and from 0.3 to 2.5 cm 2/yr in the layer below (up to 40 cm thick) and net sediment accumulation rates of approximately zero to 0.14 g/cm 2 yr were calculated for these areas.

  14. 49 CFR 178.505 - Standards for aluminum drums.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Standards for aluminum drums. 178.505 Section 178... PACKAGINGS Non-bulk Performance-Oriented Packaging Standards § 178.505 Standards for aluminum drums. (a) The following are the identification codes for aluminum drums: (1) 1B1 for a non-removable head aluminum...

  15. 29 CFR 1926.553 - Base-mounted drum hoists.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 29 Labor 8 2013-07-01 2013-07-01 false Base-mounted drum hoists. 1926.553 Section 1926.553 Labor... § 1926.553 Base-mounted drum hoists. (a) General requirements. (1) Exposed moving parts such as gears... is ineffective. (4) All base-mounted drum hoists in use shall meet the applicable requirements...

  16. 29 CFR 1926.553 - Base-mounted drum hoists.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 8 2012-07-01 2012-07-01 false Base-mounted drum hoists. 1926.553 Section 1926.553 Labor... § 1926.553 Base-mounted drum hoists. (a) General requirements. (1) Exposed moving parts such as gears... is ineffective. (4) All base-mounted drum hoists in use shall meet the applicable requirements...

  17. 29 CFR 1926.553 - Base-mounted drum hoists.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 8 2011-07-01 2011-07-01 false Base-mounted drum hoists. 1926.553 Section 1926.553 Labor... § 1926.553 Base-mounted drum hoists. (a) General requirements. (1) Exposed moving parts such as gears... is ineffective. (4) All base-mounted drum hoists in use shall meet the applicable requirements...

  18. 29 CFR 1926.553 - Base-mounted drum hoists.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Base-mounted drum hoists. 1926.553 Section 1926.553 Labor... § 1926.553 Base-mounted drum hoists. (a) General requirements. (1) Exposed moving parts such as gears... is ineffective. (4) All base-mounted drum hoists in use shall meet the applicable requirements...

  19. 29 CFR 1926.553 - Base-mounted drum hoists.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 8 2014-07-01 2014-07-01 false Base-mounted drum hoists. 1926.553 Section 1926.553 Labor... § 1926.553 Base-mounted drum hoists. (a) General requirements. (1) Exposed moving parts such as gears... is ineffective. (4) All base-mounted drum hoists in use shall meet the applicable requirements...

  20. 21 CFR 886.4230 - Ophthalmic knife test drum.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Ophthalmic knife test drum. 886.4230 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4230 Ophthalmic knife test drum. (a) Identification. An ophthalmic knife test drum is a device intended to test the keenness of ophthalmic...

  1. 21 CFR 886.4230 - Ophthalmic knife test drum.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ophthalmic knife test drum. 886.4230 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4230 Ophthalmic knife test drum. (a) Identification. An ophthalmic knife test drum is a device intended to test the keenness of ophthalmic...

  2. 30 CFR 75.1436 - Drum end attachment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drum end attachment. 75.1436 Section 75.1436... attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one... that the attachment is a design feature of the hoist drum. Design feature means either the...

  3. 30 CFR 77.1436 - Drum end attachment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drum end attachment. 77.1436 Section 77.1436... Hoisting Wire Ropes § 77.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached... anchor bolts, clamps, or wedges, provided that the attachment is a design feature of the hoist...

  4. 30 CFR 75.1436 - Drum end attachment.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Drum end attachment. 75.1436 Section 75.1436... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Hoisting and Mantrips Wire Ropes § 75.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making...

  5. 21 CFR 886.4230 - Ophthalmic knife test drum.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Ophthalmic knife test drum. 886.4230 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4230 Ophthalmic knife test drum. (a) Identification. An ophthalmic knife test drum is a device intended to test the keenness of ophthalmic...

  6. 21 CFR 886.4230 - Ophthalmic knife test drum.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Ophthalmic knife test drum. 886.4230 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4230 Ophthalmic knife test drum. (a) Identification. An ophthalmic knife test drum is a device intended to test the keenness of ophthalmic...

  7. 30 CFR 75.1436 - Drum end attachment.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Drum end attachment. 75.1436 Section 75.1436... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Hoisting and Mantrips Wire Ropes § 75.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making...

  8. 21 CFR 886.4230 - Ophthalmic knife test drum.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Ophthalmic knife test drum. 886.4230 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4230 Ophthalmic knife test drum. (a) Identification. An ophthalmic knife test drum is a device intended to test the keenness of ophthalmic...

  9. 30 CFR 75.1436 - Drum end attachment.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Drum end attachment. 75.1436 Section 75.1436... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Hoisting and Mantrips Wire Ropes § 75.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making...

  10. Unsteady-state VOC transport in vented waste drums

    SciTech Connect

    Liekhus, K.J.; Gresham, G.L.; Peterson, E.S.; Rae, C.; Hotz, N.J.; Connolly, M.J.

    1993-08-01

    A model of unsteady-state volatile organic compound (VOC) transport in a vented waste drum has been developed. Model predictions of the VOC concentration in the innermost layer of confinement and the drum headspace are compared to measurements in lab-scale simulated waste drums.

  11. Microsatellite primers for red drum (Sciaenops ocellatus)

    Technology Transfer Automated Retrieval System (TEKTRAN)

    In this note, we document polymerase-chain-reaction (PCR) primer pairs for 101, nuclear-encoded microsatellites designed and developed from a red drum (Sciaenops ocellatus) genomic library. The 101 microsatellites (Genbank Accession Numbers EU015882-EU015982) were amplified successfully and used to...

  12. [Nineteenth century physicians against drum perforation].

    PubMed

    Kierzek, A

    1995-01-01

    The trials of "organic" closure of drum perforation are described. The achievements of Adam Politzer, Hermann Schwartze, Joseph Gruber are presented. The first who used term "myringoplasty" was Emil Berthold. The "epochal" method of Wasilij Okuniew and achievements of Beniamin Gomperz are also depicted. The scientific activities of Polish otologists: Ludwik Guranowski and Rafai Spira were presented.

  13. Evaluation of residue drum storage safety risks

    SciTech Connect

    Conner, W.V.

    1994-06-17

    A study was conducted to determine if any potential safety problems exist in the residue drum backlog at the Rocky Flats Plant. Plutonium residues stored in 55-gallon drums were packaged for short-term storage until the residues could be processed for plutonium recovery. These residues have now been determined by the Department of Energy to be waste materials, and the residues will remain in storage until plans for disposal of the material can be developed. The packaging configurations which were safe for short-term storage may not be safe for long-term storage. Interviews with Rocky Flats personnel involved with packaging the residues reveal that more than one packaging configuration was used for some of the residues. A tabulation of packaging configurations was developed based on the information obtained from the interviews. A number of potential safety problems were identified during this study, including hydrogen generation from some residues and residue packaging materials, contamination containment loss, metal residue packaging container corrosion, and pyrophoric plutonium compound formation. Risk factors were developed for evaluating the risk potential of the various residue categories, and the residues in storage at Rocky Flats were ranked by risk potential. Preliminary drum head space gas sampling studies have demonstrated the potential for formation of flammable hydrogen-oxygen mixtures in some residue drums.

  14. Extendible column can be stowed on drum

    NASA Technical Reports Server (NTRS)

    Holtz, G. M.; Howard, E. A.

    1965-01-01

    Column formed from a series of segments held together by an internal spring or cable can be coiled on a drum or extended into a rigid structure. This storable coil is useful in boring for soil samples and supporting electrical and optical sensors.

  15. Pu Anion Exchange Process Intensification

    SciTech Connect

    Taylor-Pashow, K.

    2015-10-08

    This project seeks to improve the efficiency of the plutonium anion-exchange process for purifying Pu through the development of alternate ion-exchange media. The objective of the project in FY15 was to develop and test a porous foam monolith material that could serve as a replacement for the current anion-exchange resin, Reillex® HPQ, used at the Savannah River Site (SRS) for purifying Pu. The new material provides advantages in efficiency over the current resin by the elimination of diffusive mass transport through large granular resin beads. By replacing the large resin beads with a porous foam there is much more efficient contact between the Pu solution and the anion-exchange sites present on the material. Several samples of a polystyrene based foam grafted with poly(4-vinylpyridine) were prepared and the Pu sorption was tested in batch contact tests.

  16. Calibration of the Lawrence Livermore National Laboratory Passive-Active Neutron Drum Shuffler for Measurement of Highly Enriched Uranium in Mixed Oxide

    SciTech Connect

    Mount, M; O'Connell, W; Cochran, C; Rinard, P; Dearborn, D; Endres, E

    2002-05-23

    As a follow-on to the Lawrence Livermore National Laboratory (LLNL) effort to calibrate the LLNL passive-active neutron drum (PAN) shuffler for measurement of highly enriched uranium (HEU) oxide, a method has been developed to extend the use of the PAN shuffler to the measurement of HEU in mixed uranium-plutonium (U-Pu) oxide. This method uses the current LLNL HEU oxide calibration algorithms, appropriately corrected for the mixed U-Pu oxide assay time, and recently developed PuO{sub 2} calibration algorithms to yield the mass of {sup 235}U present via differences between the expected count rate for the PuO{sub 2} and the measured count rate of the mixed U-Pu oxide. This paper describes the LLNL effort to use PAN shuffler measurements of units of certified reference material (CRM) 149 [uranium (93% Enriched) Oxide - U{sub 3}O{sub 8} Standard for Neutron Counting Measurements] and CRM 146 [Uranium Isotopic Standard for Gamma Spectrometry Measurements] and a selected set of LLNL PuO{sub 2}-bearing containers in consort with Monte Carlo simulations of the PAN shuffler response to each to (1) establish and validate a correction to the HEU calibration algorithm for the mixed U-Pu oxide assay time, (2) develop a PuO{sub 2} calibration algorithm that includes the effect of PuO{sub 2} density (2.4 g/cm{sup 3} to 4.8 g/cm{sup 3}) and container size (8.57 cm to 9.88 cm inside diameter and 9.60 cm to 13.29 cm inside height) on the PAN shuffler response, and (3) develop and validate the method for establishing the mass of {sup 235}U present in an unknown of mixed U-Pu oxide.

  17. THERMAL PERFORMANCE ANALYSIS FOR WSB DRUM

    SciTech Connect

    Lee, S

    2008-06-26

    The Nuclear Nonproliferation Programs Design Authority is in the design stage of the Waste Solidification Building (WSB) for the treatment and solidification of the radioactive liquid waste streams generated by the Pit Disassembly and Conversion Facility (PDCF) and Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF). The waste streams will be mixed with a cementitious dry mix in a 55-gallon waste container. Savannah River National Laboratory (SRNL) has been performing the testing and evaluations to support technical decisions for the WSB. Engineering Modeling & Simulation Group was requested to evaluate the thermal performance of the 55-gallon drum containing hydration heat source associated with the current baseline cement waste form. A transient axi-symmetric heat transfer model for the drum partially filled with waste form cement has been developed and heat transfer calculations performed for the baseline design configurations. For this case, 65 percent of the drum volume was assumed to be filled with the waste form, which has transient hydration heat source, as one of the baseline conditions. A series of modeling calculations has been performed using a computational heat transfer approach. The baseline modeling results show that the time to reach the maximum temperature of the 65 percent filled drum is about 32 hours when a 43 C initial cement temperature is assumed to be cooled by natural convection with 27 C external air. In addition, the results computed by the present model were compared with analytical solutions. The modeling results will be benchmarked against the prototypic test results. The verified model will be used for the evaluation of the thermal performance for the WSB drum.

  18. Food of freshwater drum in western Lake Erie

    USGS Publications Warehouse

    Bur, Michael T.

    1982-01-01

    The abundance of freshwater drum (Aplodinotus grunniens) suggests they play an important role in the Lake Erie ecosystem. Our analysis of freshwater drum digestive tracts and macrobenthic samples collected from western Lake Erie indicates that drum were selective feeders. Planktonic cladocerans and larval midges (Chironomidae) were the primary prey organisms eaten by drum. Young-of-the-year fed mostly on cladocerans, while yearling and older drum ate both cladocerans and midge larvae. Decapods, pelecypods, and fish were found only in the digestive tracts of drum longer than 250 mm. While the most abundant organisms in benthic samples were cladocerans (ephippial) and oligochaetes (89.5% by number), they constituted less than 1% of the diet. An evaluation of food selectivity, using Ivlev's index of electivity for benthic organisms, indicated that adult drum preferred midges to any other benthic food.

  19. Recovery of 238PuO2 by Molten Salt Oxidation Processing of 238PuO2 Contaminated Combustibles (Part II)

    NASA Astrophysics Data System (ADS)

    Remerowski, Mary Lynn; Dozhier, C.; Krenek, K.; VanPelt, C. E.; Reimus, M. A.; Spengler, D.; Matonic, J.; Garcia, L.; Rios, E.; Sandoval, F.; Herman, D.; Hart, R.; Ewing, B.; Lovato, M.; Romero, J. P.

    2005-02-01

    Pu-238 heat sources are used to fuel radioisotope thermoelectric generators (RTG) used in space missions. The demand for this fuel is increasing, yet there are currently no domestic sources of this material. Much of the fuel is material reprocessed from other sources. One rich source of Pu-238 residual material is that from contaminated combustible materials, such as cheesecloth, ion exchange resins and plastics. From both waste minimization and production efficiency standpoints, the best solution is to recover this material. One way to accomplish separation of the organic component from these residues is a flameless oxidation process using molten salt as the matrix for the breakdown of the organic to carbon dioxide and water. The plutonium is retained in the salt, and can be recovered by dissolution of the carbonate salt in an aqueous solution, leaving the insoluble oxide behind. Further aqueous scrap recovery processing is used to purify the plutonium oxide. Recovery of the plutonium from contaminated combustibles achieves two important goals. First, it increases the inventory of Pu-238 available for heat source fabrication. Second, it is a significant waste minimization process. Because of its thermal activity (0.567 W per gram), combustibles must be packaged for disposition with much lower amounts of Pu-238 per drum than other waste types. Specifically, cheesecloth residues in the form of pyrolyzed ash (for stabilization) are being stored for eventual recovery of the plutonium.

  20. Program Pu Futures 2006

    SciTech Connect

    Fluss, M

    2006-06-12

    The coordination chemistry of plutonium remains relatively unexplored. Thus, the fundamental coordination chemistry of plutonium is being studied using simple multi-dentate ligands with the intention that the information gleaned from these studies may be used in the future to develop plutonium-specific sequestering agents. Towards this goal, hard Lewis-base donors are used as model ligands. Maltol, an inexpensive natural product used in the commercial food industry, is an ideal ligand because it is an all-oxygen bidentate donor, has a rigid structure, and is of small enough size to impose little steric strain, allowing the coordination preferences of plutonium to be the deciding geometric factor. Additionally, maltol is the synthetic precursor of 3,4-HOPO, a siderophore-inspired bidentate moiety tested by us previously as a possible sequestering agent for plutonium under acidic conditions. As comparisons to the plutonium structure, Ce(IV) complexes of the same and related ligands were examined as well. Cerium(IV) complexes serve as good models for plutonium(IV) structures because Ce(IV) has the same ionic radius as Pu(IV) (0.94 {angstrom}). Plutonium(IV) maltol crystals were grown out of a methanol/water solution by slow evaporation to afford red crystals that were evaluated at the Advanced Light Source at Lawrence Berkeley National Laboratory using single crystal X-ray diffraction. Cerium(IV) complexes with maltol and bromomaltol were crystallized via slow evaporation of the mother liquor to afford tetragonal, black crystals. All three complexes crystallize in space group I4{sub 1}/a. The Ce(IV) complex is isostructural with the Pu(IV) complex, in which donating oxygens adopt a trigonal dodecahedral geometry around the metal with the maltol rings parallel to the crystallographic S{sub 4} axis and lying in a non-crystallographic mirror plane of D{sub 2d} molecular symmetry (Fig 1). The metal-oxygen bonds in both maltol complexes are equal to within 0.04 {angstrom

  1. Characterization of In-Drum Drying Products

    SciTech Connect

    Kroselj, V.; Jankovic, M.; Skanata, D.; Medakovic, S.; Harapin, D.; Hertl, B.

    2006-07-01

    A few years ago Krsko NPP decided to introduce In-Drum Drying technology for treatment and conditioning of evaporator concentrates and spent ion resins. The main reason to employ this technology was the need for waste volume reduction and experience with vermiculite-cement solidification that proved inadequate for Krsko NPP. Use of In-Drum Drying technology was encouraged by good experience in the field at some German and Spanish NPP's. In the paper, solidification techniques in vermiculite-cement matrix and In-Drum Drying System are described briefly. The resulting waste forms (so called solidification and dryer products) and containers that are used for interim storage of these wastes are described as well. A comparison of the drying versus solidification technology is performed and advantages as well as disadvantages are underlined. Experience gained during seven years of system operation has shown that crying technology resulted in volume reduction by factor of 20 for evaporator concentrates, and by factor of 5 for spent ion resin. Special consideration is paid to the characterization of dryer products. For evaporator concentrates the resulting waste form is a solid salt block with up to 5% bound water. It is packaged in stainless steel drums (net volume of 200 l) with bolted lids and lifting rings. The fluidized spent ion resins (primary and blow-down) are sluiced into the spent resin drying tank. The resin is dewatered and dried by electrical jacket heaters. The resulting waste (i.e. fine granulates) is directly discharged into a shielded stainless steel drum with bolted lid and lifting rings. Characterization of both waste forms has been performed in accordance with recommendations given in Characterization of Radioactive Waste Forms and Packages issued by International Atomic Energy Agency, 1997. This means that radiological, chemical, physical, mechanical, biological and thermal properties of the waste form has been taken into consideration. In the paper

  2. Potential VOC Deflagrations in a Vented TRU Drum

    SciTech Connect

    Mukesh, GUPTA

    2005-04-07

    The objective of the analysis is to examine the potential for lid ejection from a vented transuranic (TRU) waste drum due to pressure buildup caused by the deflagration of hydrogen and volatile organic compounds (VOCs) inside the drum. In this analysis, the AICC pressure for a stoichiometric mixture of VOCs is calculated and then compared against the experimental peak pressure of stoichiometric combustion of propane and hexane in a combustion chamber. The experimental peak pressures of propane and hexane are about 12 percent lower than the calculated AICC pressure. Additional losses in the drum are calculated due to venting of the gases, drum bulging, waste compaction, and heat losses from the presence of waste in the drum. After accounting for these losses, the final pressures are compared to the minimum observed pressure that ejects the lid from a TRU drum. The ejection pressure of 105 psig is derived from data that was recorded for a series of tests where hydrogen-air mixtures were ignited inside sealed TRU drums. Since the calculated pressures are below the minimum lid ejection pressure, none of the VOCs and the hydrogen (up to 4 percent) mixtures present in the TRU waste drum is expected to cause lid ejection if ignited. The analysis of potential VOC deflagrations in a vented TRU drum can be applied across the DOE-Complex since TRU waste is stored in drums throughout the complex.

  3. DEGRADATION EVALUATION OF HEAVY WATER DRUMS AND TANKS

    SciTech Connect

    Mickalonis, J.; Vormelker, P.

    2009-07-31

    Heavy water with varying chemistries is currently being stored in over 6700 drums in L- and K-areas and in seven tanks in L-, K-, and C-areas. A detailed evaluation of the potential degradation of the drums and tanks, specific to their design and service conditions, has been performed to support the demonstration of their integrity throughout the desired storage period. The 55-gallon drums are of several designs with Type 304 stainless steel as the material of construction. The tanks have capacities ranging from 8000 to 45600 gallons and are made of Type 304 stainless steel. The drums and tanks were designed and fabricated to national regulations, codes and standards per procurement specifications for the Savannah River Site. The drums have had approximately 25 leakage failures over their 50+ years of use with the last drum failure occurring in 2003. The tanks have experienced no leaks to date. The failures in the drums have occurred principally near the bottom weld, which attaches the bottom to the drum sidewall. Failures have occurred by pitting, crevice and stress corrosion cracking and are attributable, in part, to the presence of chloride ions in the heavy water. Probable degradation mechanisms for the continued storage of heavy water were evaluated that could lead to future failures in the drum or tanks. This evaluation will be used to support establishment of an inspection plan which will include susceptible locations, methods, and frequencies for the drums and tanks to avoid future leakage failures.

  4. Slit-Drum Camera For Projectile Studies

    NASA Astrophysics Data System (ADS)

    Liangyi, Chen; Shaoxiang, Zhou; Guanhua, Cha; Yuxi, Hu

    1983-03-01

    The' model XF-70 slit-drum camera has been developed to record projectile in flight for observation and acquisition. It has two operation modes: (1) synchro-ballistic photography, (2) streak record. The film is located on the inner surface of rotating drum to make it travel. The folding mirror is arranged to reflect light beam 90 degree on to film. The assembly of folding mirror and slit aperture can be together rotated about the optical axis of objective so that the camera makes a feature of recording projectile having any launching angle either in synchro-ballistic photography or in streak record through prerotating the folding mirror assembly by an appropriate angle. The mechanical-electric shutter preventing film from reexposing is close to the slit aperture. The loading mechanism is designed for use in daylight. LED fiducial mark and timing mark are printed at the edges of the frame for accurate measurements.

  5. Simulating Lahars Using A Rotating Drum

    NASA Astrophysics Data System (ADS)

    Neather, Adam; Lube, Gert; Jones, Jim; Cronin, Shane

    2014-05-01

    A large (0.5 m in diameter, 0.15 m wide) rotating drum is used to investigate the erosion and deposition mechanics of lahars. To systematically simulate the conditions occurring in natural mass flows our experimental setup differs from the common rotating drum employed in industrial/engineering studies. Natural materials with their typical friction properties are used, as opposed to the frequently employed spherical glass beads; the drum is completely water-proof, so solid/air and solid/liquid mixtures can be investigated; the drum velocity and acceleration can be precisely controlled using a software interface to a micro-controller, allowing for the study of steady, unsteady and intermediate flow regimes. The drum has a toughened glass door, allowing high-resolution, high-speed video recording of the material inside. Vector maps of the velocities involved in the flows are obtained using particle image velocimetry (PIV). The changes in velocity direction and/or magnitude are used to locate the primary internal boundaries between layers of opposite flow direction, as well as secondary interfaces between shear layers. A range of variables can be measured: thickness and number of layers; the curvature of the free surface; frequency of avalanching; position of the centre of mass of the material; and the velocity profiles of the flowing material. Experiments to date have focussed on dry materials, and have had a fill factor of approximately 0.3. Combining these measured variables allows us to derive additional data of interest, such as mass and momentum flux. It is these fluxes that we propose will allow insight into the erosion/deposition mechanics of a lahar. A number of conclusions can be drawn to date. A primary interface separates flowing and passive region (this interface has been identified in previous studies). As well as the primary interface, the flowing layer separates into individual shear layers, with individual erosion/deposition and flow histories. This

  6. [Hypopharyngeal carcinoma and red ear drum].

    PubMed

    Bender, B; Widmann, G; Riechelmann, H; Schmutzhard, J

    2011-04-01

    A 46-year-old male patient with an unresectable hypopharyngeal carcinoma was treated with primary radio-chemotherapy. At follow-up, the patient presented with a red ear drum and combined hearing loss. Because of radiotherapy-induced tubal dysfunction, paracentesis was performed. Biopsy of the polypoid middle ear mucosa revealed petrous bone infiltration of hypopharyngeal carcinoma. MRI studies revealed paracarotideal tumor infiltration to the petrous bone and the middle ear arising from a cervical retropharyngeal lymph node metastasis. PMID:20963385

  7. Size limitation on zebra mussels consumed by freshwater drum may preclude the effectiveness of drum as a biological controller

    USGS Publications Warehouse

    French, John R. P.; Love, Joy G.

    1995-01-01

    The septa lengths of bivalve shells were used to estimate shell lengths of the largest zebra mussels (Dreissena polymorpha) crushed and consumed by freshwater drum (Aplodinotus grunniens) to determine if size limitation could preclude the effectiveness of drum as a biological controller of the zebra mussel. We examined gut samples of drum (273 to 542 mm long) collected from western Lake Erie in 1991, found the largest mussel (shell length = 21.4 mm) in the 11th largest drum (TL = 405 mm), and observed a reduction of mussel size in larger drum. The lack of a relationship between mussel size and drum size for larger specimens suggests that either drum prefer smaller mussels or the gape between the upper and lower pharyngeal teeth restricts drum feeding to zebra mussels of limited size. Although drum may reduce zebra mussel populations, because of the apparent size limitation of prey it is unlikely that drum would be fully effective as a biological controller; thus, this fish should not be introduced beyond its native range for that purpose.

  8. Screening and Spectral Summing of LANL Empty Waste Drums - 13226

    SciTech Connect

    Gruetzmacher, Kathleen M.; Bustos, Roland M.; Ferran, Scott G.; Gallegos, Lucas E.; Lucero, Randy P.

    2013-07-01

    Empty 55-gallon drums that formerly held transuranic (TRU) waste (often over-packed in 85- gallon drums) are generated at LANL and require radiological characterization for disposition. These drums are typically measured and analyzed individually using high purity germanium (HPGe) gamma detectors. This approach can be resource and time intensive. For a project requiring several hundred drums to be characterized in a short time frame, an alternative approach was developed. The approach utilizes a combination of field screening and spectral summing that was required to be technically defensible and meet the Nevada Nuclear Security Site (NNSS) Waste Acceptance Criteria (WAC). In the screening phase of the operation, the drums were counted for 300 seconds (compared to 600 seconds for the typical approach) and checked against Low Level (LL)/TRU thresholds established for each drum configuration and detector. Multiple TRU nuclides and multiple gamma rays for each nuclide were evaluated using an automated spreadsheet utility that can process data from up to 42 drums at a time. Screening results were reviewed by an expert analyst to confirm the field LL/TRU determination. The spectral summing analysis technique combines spectral data (channel-by-channel) associated with a group of individual waste containers producing a composite spectrum. The grouped drums must meet specific similarity criteria. Another automated spreadsheet utility was used to spectral sum data from an unlimited number of similar drums grouped together. The composite spectrum represents a virtual combined drum for the group of drums and was analyzed using the SNAP{sup TM}/Radioassay Data Sheet (RDS)/Batch Data Report (BDR) method. The activity results for a composite virtual drum were divided equally amongst the individual drums to generate characterization results for each individual drum in the group. An initial batch of approximately 500 drums were measured and analyzed in less than 2 months in 2011

  9. Active Drumming Experience Increases Infants’ Sensitivity to Audiovisual Synchrony during Observed Drumming Actions

    PubMed Central

    Timmers, Renee; Hunnius, Sabine

    2015-01-01

    In the current study, we examined the role of active experience on sensitivity to multisensory synchrony in six-month-old infants in a musical context. In the first of two experiments, we trained infants to produce a novel multimodal effect (i.e., a drum beat) and assessed the effects of this training, relative to no training, on their later perception of the synchrony between audio and visual presentation of the drumming action. In a second experiment, we then contrasted this active experience with the observation of drumming in order to test whether observation of the audiovisual effect was as effective for sensitivity to multimodal synchrony as active experience. Our results indicated that active experience provided a unique benefit above and beyond observational experience, providing insights on the embodied roots of (early) music perception and cognition. PMID:26111226

  10. Active Drumming Experience Increases Infants' Sensitivity to Audiovisual Synchrony during Observed Drumming Actions.

    PubMed

    Gerson, Sarah A; Schiavio, Andrea; Timmers, Renee; Hunnius, Sabine

    2015-01-01

    In the current study, we examined the role of active experience on sensitivity to multisensory synchrony in six-month-old infants in a musical context. In the first of two experiments, we trained infants to produce a novel multimodal effect (i.e., a drum beat) and assessed the effects of this training, relative to no training, on their later perception of the synchrony between audio and visual presentation of the drumming action. In a second experiment, we then contrasted this active experience with the observation of drumming in order to test whether observation of the audiovisual effect was as effective for sensitivity to multimodal synchrony as active experience. Our results indicated that active experience provided a unique benefit above and beyond observational experience, providing insights on the embodied roots of (early) music perception and cognition. PMID:26111226

  11. Ribbon channel plate rotating drum DNA sequencing device.

    PubMed

    Douthart, R J; Welt, M; Walling, L

    1996-01-01

    A new design DNA sequencing electrophoresis device is described. The device, called the ribbon channeled plate rotating drum (rprd), consists of two major components, the plate assembly and the drum assembly. The plate assembly contains a machined or etched plate of individual micro-channels called the ribbon channeled plate. The ribbon channeled plate and other components of the plate assembly combine the advantages of thin gels and capillary arrays in a single unit with few of the disadvantages. The other major component of rprd is the drum assembly, which facilitates direct blotting onto deposition membranes affixed to a large plastic drum. The drum with attached membrane and deposited electrophoretically resolved ladders is easily moved to special units facilitating downstream processing and detection. The drum unit, although versatile, is specifically designed to be used with multiplex sequencing. PMID:8907517

  12. Characterization and handling of 7500 old drums in Studsvik

    SciTech Connect

    Ehrs, Carin; Lindberg, Maria; Lorenzen, Joachim

    2003-02-27

    7500 old drums were characterized and sorted into a number of categories. The sorting had two main purposes the first is to divide the drums into fractions that have the same content or origin or some other sorting criteria. The second purpose is not less important, it was to limit the amount of drums to work with at each point in time and therefore get a good overview of the drums. The third reason for handling the drums were that some was in poor condition since they previously had been stored outdoors. The drums were sorted into two main fractions, one with Studsvik-ID numbers and one without. These two fractions were then divided into sub-fractions depending on content, origin, dose-rate and a recommended final repository. The work is not yet completed but the procedures are established and work well.

  13. Determination of plutonium isotopes (238Pu, 239Pu, 240Pu, 241Pu) in environmental samples using radiochemical separation combined with radiometric and mass spectrometric measurements.

    PubMed

    Xu, Yihong; Qiao, Jixin; Hou, Xiaolin; Pan, Shaoming; Roos, Per

    2014-02-01

    This paper reports an analytical method for the determination of plutonium isotopes ((238)Pu, (239)Pu, (240)Pu, (241)Pu) in environmental samples using anion exchange chromatography in combination with extraction chromatography for chemical separation of Pu. Both radiometric methods (liquid scintillation counting and alpha spectrometry) and inductively coupled plasma mass spectrometry (ICP-MS) were applied for the measurement of plutonium isotopes. The decontamination factors for uranium were significantly improved up to 7.5 × 10(5) for 20 g soil compared to the level reported in the literature, this is critical for the measurement of plutonium isotopes using mass spectrometric technique. Although the chemical yield of Pu in the entire procedure is about 55%, the analytical results of IAEA soil 6 and IAEA-367 in this work are in a good agreement with the values reported in the literature or reference values, revealing that the developed method for plutonium determination in environmental samples is reliable. The measurement results of (239+240)Pu by alpha spectrometry agreed very well with the sum of (239)Pu and (240)Pu measured by ICP-MS. ICP-MS can not only measure (239)Pu and (240)Pu separately but also (241)Pu. However, it is impossible to measure (238)Pu using ICP-MS in environmental samples even a decontamination factor as high as 10(6) for uranium was obtained by chemical separation. PMID:24401459

  14. Determination of plutonium isotopes (238Pu, 239Pu, 240Pu, 241Pu) in environmental samples using radiochemical separation combined with radiometric and mass spectrometric measurements.

    PubMed

    Xu, Yihong; Qiao, Jixin; Hou, Xiaolin; Pan, Shaoming; Roos, Per

    2014-02-01

    This paper reports an analytical method for the determination of plutonium isotopes ((238)Pu, (239)Pu, (240)Pu, (241)Pu) in environmental samples using anion exchange chromatography in combination with extraction chromatography for chemical separation of Pu. Both radiometric methods (liquid scintillation counting and alpha spectrometry) and inductively coupled plasma mass spectrometry (ICP-MS) were applied for the measurement of plutonium isotopes. The decontamination factors for uranium were significantly improved up to 7.5 × 10(5) for 20 g soil compared to the level reported in the literature, this is critical for the measurement of plutonium isotopes using mass spectrometric technique. Although the chemical yield of Pu in the entire procedure is about 55%, the analytical results of IAEA soil 6 and IAEA-367 in this work are in a good agreement with the values reported in the literature or reference values, revealing that the developed method for plutonium determination in environmental samples is reliable. The measurement results of (239+240)Pu by alpha spectrometry agreed very well with the sum of (239)Pu and (240)Pu measured by ICP-MS. ICP-MS can not only measure (239)Pu and (240)Pu separately but also (241)Pu. However, it is impossible to measure (238)Pu using ICP-MS in environmental samples even a decontamination factor as high as 10(6) for uranium was obtained by chemical separation.

  15. Drum-mate: interaction dynamics and gestures in human-humanoid drumming experiments

    NASA Astrophysics Data System (ADS)

    Kose-Bagci, Hatice; Dautenhahn, Kerstin; Syrdal, Dag S.; Nehaniv, Chrystopher L.

    2010-06-01

    This article investigates the role of interaction kinesics in human-robot interaction (HRI). We adopted a bottom-up, synthetic approach towards interactive competencies in robots using simple, minimal computational models underlying the robot's interaction dynamics. We present two empirical, exploratory studies investigating a drumming experience with a humanoid robot (KASPAR) and a human. In the first experiment, the turn-taking behaviour of the humanoid is deterministic and the non-verbal gestures of the robot accompany its drumming to assess the impact of non-verbal gestures on the interaction. The second experiment studies a computational framework that facilitates emergent turn-taking dynamics, whereby the particular dynamics of turn-taking emerge from the social interaction between the human and the humanoid. The results from the HRI experiments are presented and analysed qualitatively (in terms of the participants' subjective experiences) and quantitatively (concerning the drumming performance of the human-robot pair). The results point out a trade-off between the subjective evaluation of the drumming experience from the perspective of the participants and the objective evaluation of the drumming performance. A certain number of gestures was preferred as a motivational factor in the interaction. The participants preferred the models underlying the robot's turn-taking which enable the robot and human to interact more and provide turn-taking closer to 'natural' human-human conversations, despite differences in objective measures of drumming behaviour. The results are consistent with the temporal behaviour matching hypothesis previously proposed in the literature which concerns the effect that the participants adapt their own interaction dynamics to the robot's.

  16. Safety analysis report for packaging (onsite) steel drum

    SciTech Connect

    McCormick, W.A.

    1998-09-29

    This Safety Analysis Report for Packaging (SARP) provides the analyses and evaluations necessary to demonstrate that the steel drum packaging system meets the transportation safety requirements of HNF-PRO-154, Responsibilities and Procedures for all Hazardous Material Shipments, for an onsite packaging containing Type B quantities of solid and liquid radioactive materials. The basic component of the steel drum packaging system is the 208 L (55-gal) steel drum.

  17. Remote radioactive waste drum inspection with an autonomous mobile robot

    SciTech Connect

    Heckendorn, F.M.; Ward, C.R.; Wagner, D.G.

    1992-11-01

    An autonomous mobile robot is being developed to perform remote surveillance and inspection task on large numbers of stored radioactive waste drums. The robot will be self guided through narrow storage aisles and record the visual image of each viewable drum for subsequent off line analysis and archiving. The system will remove the personnel from potential exposure to radiation, perform the require inspections, and improve the ability to assess the long term trends in drum conditions.

  18. Remote radioactive waste drum inspection with an autonomous mobile robot

    SciTech Connect

    Heckendorn, F.M.; Ward, C.R.; Wagner, D.G.

    1992-01-01

    An autonomous mobile robot is being developed to perform remote surveillance and inspection task on large numbers of stored radioactive waste drums. The robot will be self guided through narrow storage aisles and record the visual image of each viewable drum for subsequent off line analysis and archiving. The system will remove the personnel from potential exposure to radiation, perform the require inspections, and improve the ability to assess the long term trends in drum conditions.

  19. Economical Production of Pu-238

    SciTech Connect

    Steven D. Howe; Douglas Crawford; Jorge Navarro; Terry Ring

    2013-02-01

    All space exploration missions traveling beyond Jupiter must use radioisotopic power sources for electrical power. The best isotope to power these sources is plutonium-238. The US supply of Pu-238 is almost exhausted and will be gone within the next decade. The Department of Energy has initiated a production program with a $10M allocation from NASA but the cost is estimated at over $100 M to get to production levels. The Center for Space Nuclear Research has conceived of a potentially better process to produce Pu-238 earlier and for significantly less cost. The new process will also produce dramatically less waste. Potentially, the front end costs could be provided by private industry such that the government only had to pay for the product produced. Under a NASA Phase I NIAC grant, the CSNR has evaluated the feasibility of using a low power, commercially available nuclear reactor to produce at least 1.5 kg of Pu-238 per year. The impact on the neutronics of the reactor have been assessed, the amount of Neptunium target material estimated, and the production rates calculated. In addition, the size of the post-irradiation processing facility has been established. In addition, a new method for fabricating the Pu-238 product into the form used for power sources has been identified to reduce the cost of the final product. In short, the concept appears to be viable, can produce the amount of Pu-238 needed to support the NASA missions, can be available within a few years, and will cost significantly less than the current DOE program.

  20. Mechanical Modeling of a WIPP Drum Under Pressure

    SciTech Connect

    Smith, Jeffrey A.

    2014-11-25

    Mechanical modeling was undertaken to support the Waste Isolation Pilot Plant (WIPP) technical assessment team (TAT) investigating the February 14th 2014 event where there was a radiological release at the WIPP. The initial goal of the modeling was to examine if a mechanical model could inform the team about the event. The intention was to have a model that could test scenarios with respect to the rate of pressurization. It was expected that the deformation and failure (inability of the drum to contain any pressure) would vary according to the pressurization rate. As the work progressed there was also interest in using the mechanical analysis of the drum to investigate what would happen if a drum pressurized when it was located under a standard waste package. Specifically, would the deformation be detectable from camera views within the room. A finite element model of a WIPP 55-gallon drum was developed that used all hex elements. Analyses were conducted using the explicit transient dynamics module of Sierra/SM to explore potential pressurization scenarios of the drum. Theses analysis show similar deformation patterns to documented pressurization tests of drums in the literature. The calculated failure pressures from previous tests documented in the literature vary from as little as 16 psi to 320 psi. In addition, previous testing documented in the literature shows drums bulging but not failing at pressures ranging from 69 to 138 psi. The analyses performed for this study found the drums failing at pressures ranging from 35 psi to 75 psi. When the drums are pressurized quickly (in 0.01 seconds) there is significant deformation to the lid. At lower pressurization rates the deformation of the lid is considerably less, yet the lids will still open from the pressure. The analyses demonstrate the influence of pressurization rate on deformation and opening pressure of the drums. Analyses conducted with a substantial mass on top of the closed drum demonstrate that the

  1. Fire protection guide for solid waste metal drum storage

    SciTech Connect

    Bucci, H.M.

    1996-09-16

    This guide provides a method to assess potential fire development in drum storage facilities. The mechanism of fire propagation/spread through stored drum arrays is a complex process. It involves flame heat transfer, transient conduction,convection, and radiation between drums (stored in an array configuration). There are several phenomena which may occur when drums are exposed to fire. The most dramatic is violent lid failure which results in total lid removal. When a drum loses its lid due to fire exposure, some or all of the contents may be ejected from the drum, and both the ejected combustible material and the combustible contents remaining within the container will burn. The scope of this guide is limited to storage arrays of steel drums containing combustible (primarily Class A) and noncombustible contents. Class B combustibles may be included in small amounts as free liquid within the solid waste contents.Storage arrays, which are anticipated in this guide, include single or multi-tier palletized (steel or wood pallets) drums,high rack storage of drums, and stacked arrays of drums where plywood sheets are used between tiers. The purpose of this guide is to describe a simple methodology that estimates the consequences of a fire in drum storage arrays. The extent of fire development and the resulting heat release rates can be estimated. Release fractions applicable to this type of storage are not addressed, and the transport of contaminants away from the source is not addressed. However, such assessments require the amount of combustible material consumed and the surface area of this burning material. The methods included in this guide do provide this information.

  2. Cookoff Modeling of a WIPP waste drum (68660)

    SciTech Connect

    Hobbs, Michael L.

    2014-11-24

    A waste drum located 2150 feet underground may have been the root cause of a radiation leak on February 14, 2014. Information provided to the WIPP Technical Assessment Team (TAT) was used to describe the approximate content of the drum, which included an organic cat litter (Swheat Scoop®, or Swheat) composed of 100% wheat products. The drum also contained various nitrate salts, oxalic acid, and a nitric acid solution that was neutralized with triethanolamine (TEA). CTH-TIGER was used with the approximate drum contents to specify the products for an exothermic reaction for the drum. If an inorganic adsorbent such as zeolite had been used in lieu of the kitty litter, the overall reaction would have been endothermic. Dilution with a zeolite adsorbent might be a useful method to remediate drums containing organic kitty litter. SIERRA THERMAL was used to calculate the pressurization and ignition of the drum. A baseline simulation of drum 68660 was performed by assuming a background heat source of 0.5-10 W of unknown origin. The 0.5 W source could be representative of heat generated by radioactive decay. The drum ignited after about 70 days. Gas generation at ignition was predicted to be 300-500 psig with a sealed drum (no vent). At ignition, the wall temperature increases modestly by about 1°C, demonstrating that heating would not be apparent prior to ignition. The ignition location was predicted to be about 0.43 meters above the bottom center portion of the drum. At ignition only 3-5 kg (out of 71.6 kg total) has been converted into gas, indicating that most of the material remained available for post-ignition reaction.

  3. Automated Store Management For Drum Storage Facility

    SciTech Connect

    Koller, W.; Lang, R.

    2008-07-01

    This paper describes advanced system technology developed for a new Drum Storage Facility to be operated by Taiwan Power Company (TPC). A logistics management concept is applied for the storage of solid rad-wastes in terms of automated handling, transportation and storing as well as in terms of data management. The individual equipments, such as automated Bridge Cranes, Automatic Guided Vehicles and auxiliary systems are introduced in this paper and the store management process is outlined. The authors report furthermore on challenges during the design and engineering phase and review the project implementation from the equipment supplier's end. (authors)

  4. Distinguishing Pu Metal From Pu Oxide Using Fast Neutron Counting

    SciTech Connect

    Verbeke, J M; Chapline, G F; Nakae, L; Wurtz, R; Sheets, S

    2012-05-29

    We describe a method for simultaneously determining the {alpha}-ratio and k{sub eff} for fissile materials using fast neutrons. Our method is a generalization of the Hage-Cifarrelli method for determining k{sub eff} for fissile assemblies which utilizes the shape of the fast neutron spectrum. In this talk we illustrate the method using Monte Carlo simulations of the fast neutrons generated in PuO{sub 2} to calculate the fast neutron spectrum and Feynman correlations.

  5. Thermal sensing for characterizing the contents of waste storage drums

    NASA Technical Reports Server (NTRS)

    Philpot, W. D.; Philipson, W. R.

    1985-01-01

    The present investigation is concerned with the feasibility to employ remote sensing for the characterization of the contents of liquid chemical waste storage drums. Philipson et al. (1981) had found that, when the air temperature is changing rapidly, differences in the thermal inertia of the drum contents can lead to detectable differences in the skin temperature of the drums. Thus, postsunset, airborne thermal remote sensing could potentially provide some level of discrimination among chemical storage drums. Discrimination should be possible among steel drums filled largely with: (1) aqueous solvents, (2) organic solvents, or (3) clay packing materials. The response of a drum filled with clay packing materials should be similar to that of an empty drum. The reported study had the objective to verify the theoretical findings, taking into account the use of a hand-held infrared radiometer. It was found that under the proper conditions the temperature differences among drums with the three different types of contents will be significant and consistent.

  6. The Talking Drum: Moving toward a Psychology of Literacy Transformation.

    ERIC Educational Resources Information Center

    Gaines, Joseph H.

    1996-01-01

    Discusses how the talking drum has been a viable cultural voice for many West and Central African cultures in the acquisition of literacy. Emphasizes musical character of tonal languages and the use of the talking drum for literacy purposes. Proposes research questions regarding function and use of music and language; describes role of the talking…

  7. Rhythmic Characteristics of Improvisational Drumming among Preschool Children

    ERIC Educational Resources Information Center

    Whitcomb, Rachel

    2010-01-01

    A call-and-response drumming activity was carried out to determine the rhythmic characteristics of improvised patterns created by preschool children. Specific goals of the study were to: (1) determine the durations, start and stop times, and rhythmic patterns of improvised responses to a simple given call using drums; (2) determine the presence or…

  8. Packaging design criteria for the Type B Drum

    SciTech Connect

    Edwards, W.S.; Smith, R.J.; Wells, A.H.

    1995-09-01

    The Type B Drum package is a transportation cask capable of shipping a single 55-gal (208 L) drum of transuranic (TRU) waste. The Type B Drum is smaller than existing certified packages, such as the TRUPACT-II cask, but will allow payloads with higher thermal and gas generation rates, thus providing greater operational flexibility. The Type B Drum package has double containment so that plutonium contents and other radioactive material may be transported in Type B quantities. Conceptual designs of unshielded and shielded versions of the Type B Drum were completed in Report on the Conceptual Design of the Unshielded Type B Drum Packaging and Report on the Conceptual Design of the Shielded type B Drum Packaging (WEC 1994a, WEC 1994b), which demonstrated the Type B Drum to be a viable packaging system. A Type B package containment system must withstand the normal conditions of transport and the hypothetical accident conditions, which include a 9-m (30-ft) drop onto an unyielding surface and a 1-m (3-ft) drop onto a 15-cm (6-in.) diameter pin, and a fire and immersion scenarios.

  9. 29 CFR 1915.173 - Drums and containers.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... vessels, drums and containers containing toxic or flammable liquids or gases shall not be stored or used... pressure vessels, drums and containers of 30 gallon capacity or over containing flammable or toxic liquids...) Containers of 55 gallons or more capacity containing flammable or toxic liquid shall be surrounded by...

  10. 29 CFR 1915.173 - Drums and containers.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... vessels, drums and containers containing toxic or flammable liquids or gases shall not be stored or used... pressure vessels, drums and containers of 30 gallon capacity or over containing flammable or toxic liquids...) Containers of 55 gallons or more capacity containing flammable or toxic liquid shall be surrounded by...

  11. 29 CFR 1915.173 - Drums and containers.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... vessels, drums and containers containing toxic or flammable liquids or gases shall not be stored or used... pressure vessels, drums and containers of 30 gallon capacity or over containing flammable or toxic liquids...) Containers of 55 gallons or more capacity containing flammable or toxic liquid shall be surrounded by...

  12. 29 CFR 1915.173 - Drums and containers.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... vessels, drums and containers containing toxic or flammable liquids or gases shall not be stored or used... pressure vessels, drums and containers of 30 gallon capacity or over containing flammable or toxic liquids...) Containers of 55 gallons or more capacity containing flammable or toxic liquid shall be surrounded by...

  13. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... welded on drums designed to contain more than 40 L (11 gallons) of liquids. Body seams must be mechanically seamed or welded on drums intended to contain only solids or 40 L (11 gallons) or less of liquids... retain their protective properties under normal conditions of transport. (8) Maximum capacity of...

  14. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... contain more than 40 L (11 gallons) of liquids. Body seams must be mechanically seamed or welded on drums intended to contain only solids or 40 L (11 gallons) or less of liquids. (3) Chimes must be mechanically... properties under normal conditions of transport. (8) Maximum capacity of drum: 450 L (119 gallons)....

  15. 29 CFR 1915.173 - Drums and containers.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 7 2011-07-01 2011-07-01 false Drums and containers. 1915.173 Section 1915.173 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) OCCUPATIONAL SAFETY AND HEALTH STANDARDS FOR SHIPYARD EMPLOYMENT Portable, Unfired Pressure Vessels, Drums and Containers, Other...

  16. Drum ring removal/installation tool

    DOEpatents

    Andrade, William Andrew

    2006-11-14

    A handheld tool, or a pair of such tools, such as for use in removing/installing a bolt-type clamping ring on a container barrel/drum, where the clamping ring has a pair of clamping ends each with a throughbore. Each tool has an elongated handle and an elongated lever arm transversely connected to one end of the handle. The lever arm is capable of being inserted into the throughbore of a selected clamping end and leveraged with the handle to exert a first moment on the selected clamping end. Each tool also has a second lever arm, such as a socket with an open-ended slot, which is suspended alongside the first lever arm. The second lever arm is capable of engaging the selected clamping end and being leveraged with the handle to exert a second moment which is orthogonal to the first moment. In this manner, the first and second moments operate to hold the selected clamping end fixed relative to the tool so that the selected clamping end may be controlled with the handle. The pair of clamping ends may also be simultaneously and independently controlled with the use of two handles/tools so as to contort the geometry of the drum clamping ring and enable its removal/installation.

  17. Assay of PCM Crates and Drums using the BIL Solutions Ltd. Imaging DISPIM{sup R} System

    SciTech Connect

    Mulligan, A.; Sharpe, R.J.

    2006-07-01

    BIL Solutions Ltd Decommissioning In-Situ Plutonium Inventory Monitor (DISPIM{sup R}) is a versatile neutron and gamma assay system designed to be deployable in a wide range of decommissioning and waste management situations. The system utilizes Totals and Coincidence neutron counting to determine both total Pu mass values and the 3D Pu mass distribution inside the target object. DISPIM{sup R}'s modular, mobile design allows the system to be used in the assay of a range of objects of varying size and shape in locations where alternative monitoring equipment would not normally be available. The DISPIM{sup R} system has recently been successfully used for the in-situ measurement of crated and drummed Plutonium Contaminated Material (PCM) waste items to provide Pu mass values in preparation for their treatment as part of a decommissioning program. A description of the operation of the DISPIM{sup R} system is given, including calibration of the system prior to the on-site survey, the measurement and quality control methodology employed during assay of waste items and discussion of the data analysis techniques. The results of 'imaging' measurements (i.e. Pu mass distribution results) recorded from the PCM crate measurements are likely to be of particular benefit when planning any future operations on these waste items. The results of this DISPIM{sup R} survey represent a complete solution for the customer with minimal requirement for use of their own resources. Technically substantiated Pu mass assay results have been provided which can now be easily adopted for use in criticality safety cases for the future treatment of these waste items. In summary, the DISPIM{sup R} system has successfully delivered a safe, fast and cost effective measurement solution to this challenging assay task and demonstrated its flexibility as a PCM monitoring system. (authors)

  18. 240Pu/239Pu mass ratio in environmental samples in Finland.

    PubMed

    Salminen-Paatero, S; Nygren, U; Paatero, J

    2012-11-01

    The (240)Pu/(239)Pu mass ratio was determined with SF-ICP-MS in lichen, peat, grass, air filter, and hot particle samples obtained in Finland. The main part of the air filters were sampled in northern Finland in 1963, whereas all the other samples were collected in southern and central Finland immediately after the Chernobyl accident in 1986. The (240)Pu/(239)Pu mass ratio varied between 0.13 ± 0.01 and 0.53 ± 0.03 in the environmental samples analyzed. The values for the (240)Pu/(239)Pu ratio confirm previous estimations, based on the (238)Pu/(239+240)Pu alpha activity ratio in the same samples, that global fallout from nuclear weapons testing and deposition from the Chernobyl accident have been the main Pu contamination sources in the environment in Finland. PMID:22776691

  19. Oxidation of Pu-bearing solids: A process for Pu recovery from Rocky Flats incinerator ash

    SciTech Connect

    Karraker, D.G.

    1997-07-18

    High-fired PuO{sub 2}, RFP ash heels, and synthetic RFP incinerator ash were easily soluble after oxidation of Pu(IV) to Pu(VI) by heating with Na{sub 2}O{sub 2} or KO{sub 2} to 450{degrees} for two hours. This offers a route to the recovery of Pu from these and similar PuO{sub 2}-bearing solids that can be carried out in present equipment. Evidence for new compounds K{sub 2}PuO{sub 4}, K{sub 4}PuO{sub 5} and K{sub 6}PuO{sub 6} is presented. A process for recovery of Pu from RFP incinerator ash is presented.

  20. Neutron Screening Measurements of 110 gallon drums at T Plant

    SciTech Connect

    Mozhayev, Andrey V.; Hilliard, James R.; Berg, Randal K.

    2011-01-14

    The Pacific Northwest National Laboratory (PNNL) Nondestructive Assay (NDA) Service Center was contracted to develop and demonstrate a simple and inexpensive method of assaying 110 gallon drums at the Hanford Site’s T-Plant. The drums contained pucks of crushed old drums used for storage of transuranic (TRU) waste. The drums were to be assayed to determine if they meet the criteria for TRU or Low Level Waste (LLW). Because of the dense matrix (crushed steel drums) gamma measurement techniques were excluded and a mobile, configurable neutron system, consisting of four sequentially connected slab detectors was chosen to be used for this application. An optimum measurement configuration was determined through multiple test measurements with californium source. Based on these measurements the initial calibration of the system was performed applying the isotopic composition for aged weapon-grade plutonium. A series of background and blank puck drum measurements allowed estimating detection limits for both total (singles) and coincidence (doubles) counting techniques. It was found that even conservative estimates for minimum detection concentration using singles count rate were lower than the essential threshold of 100 nCi/g. Whereas the detection limit of coincidence counting appeared to be about as twice as high of the threshold. A series of measurements intended to verify the technique and revise the initial calibration obtained were performed at the Waste Receiving and Processing (WRAP) facility with plutonium standards. Standards with a total mass of 0.3 g of plutonium (which is estimated to be equivalent of 100 nCi/g for net waste weight of 300 kg) loaded in the test puck drum were clearly detected. The following measurements of higher plutonium loadings verified the calibration factors obtained in the initial exercise. The revised and established calibration factors were also confirmed within established uncertainties by additional measurements of plutonium

  1. Controls on Soluble Pu Concentrations in PuO2/Magnetite Suspensions

    SciTech Connect

    Felmy, Andrew R.; Moore, Dean A.; Pearce, Carolyn I.; Conradson, Steven D.; Qafoku, Odeta; Buck, Edgar C.; Rosso, Kevin M.; Ilton, Eugene S.

    2012-11-06

    Time-dependent reduction of PuO2(am) was studied over a range of pH values in the presence of aqueous Fe(II) and magnetite (Fe3O4) nanoparticles. At early time frames (up to 56 days) very little aqueous Pu was mobilized from PuO2(am), even though measured pH and redox potentials, coupled to equilibrium thermodynamic modeling indicated the potential for significant reduction of PuO2(am) to relatively soluble Pu(III). Introduction of Eu(III) or Nd(III) to the suspensions as competitive cations to displace possible sorbed Pu(III) resulted in the release of significant concentrations of aqueous Pu. However, the similarity of aqueous Pu concentrations that resulted from the introduction of Eu(III)/Nd(III) to suspensions with and without magnetite indicated that the Pu was displaced from the PuO2(am), not from magnetite. The fact that soluble forms of Pu can be displaced from the surface of PuO2(am) represents a potential, but previously unidentified, source of Pu to aqueous solution or subsurface groundwaters.

  2. Pu electronic structure and photoelectron spectroscopy

    SciTech Connect

    Joyce, John J; Durakiewicz, Tomasz; Graham, Kevin S; Bauer, Eric D; Moore, David P; Mitchell, Jeremy N; Kennison, John A; Martin, Richard L; Roy, Lindsay E; Scuseria, G. E.

    2010-01-01

    The electronic structure of PuCoGa{sub 5}, Pu metal, and PuO{sub 2} is explored using photoelectron spectroscopy. Ground state electronic properties are inferred from temperature dependent photoemission near the Fermi energy for Pu metal. Angle-resolved photoemission details the energy vs. crystaJ momentum landscape near the Fermi energy for PuCoGa{sub 5} which shows significant dispersion in the quasiparticle peak near the Fermi energy. For the Mott insulators AnO{sub 2}(An = U, Pu) the photoemission results are compared against hybrid functional calculations and the model prediction of a cross over from ionic to covalent bonding is found to be reasonable.

  3. Adsorption of Atmospheric Gases on Pu Surfaces

    SciTech Connect

    Nelson, A J; Holliday, K S; Stanford, J A; Grant, W K; Erler, R G; Allen, P G; McLean, W; Roussel, P

    2012-03-29

    Surface adsorption represents a competition between collision and scattering processes that depend on surface energy, surface structure and temperature. The surface reactivity of the actinides can add additional complexity due to radiological dissociation of the gas and electronic structure. Here we elucidate the chemical bonding of gas molecules adsorbed on Pu metal and oxide surfaces. Atmospheric gas reactions were studied at 190 and 300 K using x-ray photoelectron spectroscopy. Evolution of the Pu 4f and O 1s core-level states were studied as a function of gas dose rates to generate a set of Langmuir isotherms. Results show that the initial gas dose forms Pu{sub 2}O{sub 3} on the Pu metal surface followed by the formation of PuO{sub 2} resulting in a layered oxide structure. This work represents the first steps in determining the activation energy for adsorption of various atmospheric gases on Pu.

  4. Materials science and metallurgy of the Caribbean steel drum

    NASA Astrophysics Data System (ADS)

    Ferreyra Tello, Everaldo

    The fabrication of a steel drum (or steelpan), especially the sinking of the drum head by hand with a hammer, has been examined in detail utilizing light metallography (LM) and transmission electron microscopy (TEM). Residual microstructures corresponding to reductions in thickness of up to 50% at the bottom of the drum-head indicate that dislocation densities in the low carbon (0.04 to 0.09% C), ferritic steels, can exceed 1010 cm -2. This substructure in conjunction with a grain structure consisting of elongated grains produces hardness increases of up to 45% at the bottom of the drum head. The heat treatment (or ``burning'') of the Caribbean steel drum is an essential stage in the fabrication process and has been found to involve strain aging, which increases the hardness by an additional 5 to 20%. This is especially prominent in drum steels containing from 0.04 to 0.09% C. The strain aging combined with the strain hardening applied to the drum head sinking and note fabrication process, produces a requisite elastic-plastic interaction which allows for multi-harmonic tuning and the creation of the unique chromatic tones and harmonic overtones which are characteristic of the various instruments. These unique features of note vibrations were observed by comparing impact hardness profiles with the corresponding static Vickers hardness measurements for actual, tuned notes and the same, corresponding notes extracted from the drum head, respectively. Elastic-plastic and plastic hardness profiles were compared in unique color maps. In an effort to understand the influence of deformation on the sound of the steel drum, circular disks simulating free, ideal notes, and utilizing 316 stainless steel plates (0.05% C), were cold rolled to reductions up to 40%. Disks were hung on a wire through a hole drilled on the edge of the disk, and hit with a heavy (tungsten alloy) mallet to record the acoustic sound spectra. Requisite amounts of carbon interact with dislocations in

  5. Criticality Safety Analysis on the Mixed Be, Nat-U, and C (Graphite) Reflectors in 55-Gallon Waste Drums and Their Equivalents for HWM Applications

    SciTech Connect

    Chou, P

    2011-12-14

    The objective of this analysis is to develop and establish the technical basis on the criticality safety controls for the storage of mixed beryllium (Be), natural uranium (Nat-U), and carbon (C)/graphite reflectors in 55-gallon waste containers and/or their equivalents in Hazardous Waste Management (HWM) facilities. Based on the criticality safety limits and controls outlined in Section 3.0, the operations involving the use of mixed-reflector drums satisfy the double-contingency principle as required by DOE Order 420.1 and are therefore criticality safe. The mixed-reflector mass limit is 120 grams for each 55-gallon drum or its equivalent. a reflector waiver of 50 grams is allowed for Be, Nat-U, or C/graphite combined. The waived reflectors may be excluded from the reflector mass calculations when determining if a drum is compliant. The mixed-reflector drums are allowed to mix with the typical 55-gallon one-reflector drums with a Pu mass limit of 120 grams. The fissile mass limit for the mixed-reflector container is 65 grams of Pu equivalent each. The corresponding reflector mass limits are 300 grams of Be, and/or 100 kilograms of Nat-U, and/or 110 kilograms of C/graphite for each container. All other unaffected control parameters for the one-reflector containers remain in effect for the mixed-reflector drums. For instance, Superior moderators, such as TrimSol, Superla white mineral oil No. 9, paraffin, and polyethylene, are allowed in unlimited quantities. Hydrogenous materials with a hydrogen density greater than 0.133 gram/cc are not allowed. Also, an isolation separation of no less than 76.2 cm (30-inch) is required between a mixed array and any other array. Waste containers in the action of being transported are exempted from this 76.2-cm (30-inch) separation requirement. All deviations from the CS controls and mass limits listed in Section 3.0 will require individual criticality safety analyses on a case-by-case basis for each of them to confirm their

  6. Extinct 244Pu in Ancient Zircons

    NASA Astrophysics Data System (ADS)

    Turner, Grenville; Harrison, T. Mark; Holland, Greg; Mojzsis, Stephen J.; Gilmour, Jamie

    2004-10-01

    We have found evidence, in the form of fissiogenic xenon isotopes, for in situ decay of 244Pu in individual 4.1- to 4.2-billion-year-old zircons from the Jack Hills region of Western Australia. Because of its short half-life, 82 million years, 244Pu was extinct within 600 million years of Earth's formation. Detrital zircons are the only known relics to have survived from this period, and a study of their Pu geochemistry will allow us to date ancient metamorphic events and determine the terrestrial Pu/U ratio for comparison with the solar ratio.

  7. Leukemogenesis in heterozygous PU.1 knockout mice.

    PubMed

    Genik, Paula C; Vyazunova, Irina; Steffen, Leta S; Bacher, Jeffery W; Bielefeldt-Ohmann, Helle; McKercher, Scott; Ullrich, Robert L; Fallgren, Christina M; Weil, Michael M; Ray, F Andrew

    2014-09-01

    Most murine radiation-induced acute myeloid leukemias involve biallelic inactivation of the PU.1 gene, with one allele being lost through a radiation-induced chromosomal deletion and the other allele affected by a recurrent point mutation in codon 235 that is likely to be spontaneous. The short latencies of acute myeloid leukemias occurring in nonirradiated mice engineered with PU.1 conditional knockout or knockdown alleles suggest that once both copies of PU.1 have been lost any other steps involved in leukemogenesis occur rapidly. Yet, spontaneous acute myeloid leukemias have not been reported in mice heterozygous for a PU.1 knockout allele, an observation that conflicts with the understanding that the PU.1 codon 235 mutation is spontaneous. Here we describe experiments that show that the lack of spontaneous leukemia in PU.1 heterozygous knockout mice is not due to insufficient monitoring times or mouse numbers or the genetic background of the knockout mice. The results reveal that spontaneous leukemias that develop in mice of the mixed 129S2/SvPas and C57BL/6 background of knockout mice arise by a pathway that does not involve biallelic PU.1 mutation. In addition, the latency of radiation-induced leukemia in PU.1 heterozygous mice on a genetic background susceptible to radiation-induced leukemia indicates that the codon 235 mutation is not a rate-limiting step in radiation leukemogenesis driven by PU.1 loss.

  8. 55. BOILER CHAMBER No. 1, LOOP B, STEAM DRUM AND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    55. BOILER CHAMBER No. 1, LOOP B, STEAM DRUM AND DOWNCOMERS LOOKING EAST (LOCATION LLL) - Shippingport Atomic Power Station, On Ohio River, 25 miles Northwest of Pittsburgh, Shippingport, Beaver County, PA

  9. 49. EASTERN VIEW OF DORROLIVER VACUUM DRUM FILTER ASSEMBLY IN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    49. EASTERN VIEW OF DORR-OLIVER VACUUM DRUM FILTER ASSEMBLY IN THE FILTER CAKE HOUSE. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

  10. 4. DETAIL OF ELEVATOR DRUM AND DRIVE. Hot Springs ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. DETAIL OF ELEVATOR DRUM AND DRIVE. - Hot Springs National Park, Bathhouse Row, Fordyce Bathhouse: Mechanical & Piping Systems, State Highway 7, 1 mile north of U.S. Highway 70, Hot Springs, Garland County, AR

  11. The Play as Novel: Reappropriating Brecht's "Drums in the Night."

    ERIC Educational Resources Information Center

    Pollock, Della

    1988-01-01

    Applies Mikhail Bakhtin's theory of the novel to Bertolt Brecht's "Drums in the Night" to illuminate the play's dialogic structure and alienation value, and reappropriate its prerevolutionary dimensions for contemporary use. (MM)

  12. SWING BRIDGE AT CENTER OF SPAN. DRUM, ALTHOUGH NOT VISIBLE, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    SWING BRIDGE AT CENTER OF SPAN. DRUM, ALTHOUGH NOT VISIBLE, IS AT CENTER OF PICTURE. - Northern Avenue Swing Bridge, Spanning Fort Point Channel at boundary between Boston & South Boston, Boston, Suffolk County, MA

  13. Slit Logs and Sacred Cows: The History of the Drum.

    ERIC Educational Resources Information Center

    Music Educators Journal, 1979

    1979-01-01

    The evolution of the drum is presented in both pictures and prose, from its beginning in Africa and the Far Eastern world to its introduction to the Western world where it is now fully accepted as a serious instrument. (KC)

  14. 47. TRESTLE OVER DRUM ISLAND, WEST END OF COOPER RIVER ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    47. TRESTLE OVER DRUM ISLAND, WEST END OF COOPER RIVER SPAN, FACING NORTHWEST FROM WATER - Grace Memorial Bridge, U.S. Highway 17 spanning Cooper River & Town Creek , Charleston, Charleston County, SC

  15. View of furnace feeding into the drum type coffee dryer ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of furnace feeding into the drum type coffee dryer on second floor of structure, view towards southeast - Santaella Coffee Processing Site, Highway 139, Kilometer 10.6, Maraguez, Ponce Municipio, PR

  16. View of main hoist wire rope drum and brakes, open ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of main hoist wire rope drum and brakes, open contact boards are in view at the far right wall - Puget Sound Naval Shipyard, Portal Gantry Crane No. 42, Pier 5, Farragut Avenue, Bremerton, Kitsap County, WA

  17. Use of plutonium isotope activity ratios in dating recent sediments. [/sup 238/Pu//sup 239/Pu + /sup 240/Pu

    SciTech Connect

    Beasley, T. M.

    1982-01-01

    The majority of plutonium presently in the biosphere has come from the testing of nuclear devices. In the early 1950s, the Pu-238/239+240 activity ratio of fallout debris was > 0.04; in the more extensive test series of 1961 to 1962, the Pu-238/239+240 activity ratios were quite consistent at 0.02 to 0.03 and maximum fallout delivery occurred in mid-1963. A significant perturbation in Pu isotope activity ratios occurred in mid-1966 with the deposition of Pu-238 from the SNAP-9A reentry and burn-up. Recently deposited sediments have recorded these events and where accumulation rates are rapid (> 1 cm/y), changes in Pu isotope activity ratios can be used as a geochronological tool.

  18. Biodegradation of PuEDTA and Impacts on Pu Mobility

    SciTech Connect

    Xun, Luying; Bolton, Jr., Harvey

    2001-06-01

    Ethylenediaminetetraacetate (EDTA) and nitrilotriacetate (NTA) are synthetic chelating agents, which can form strong water-soluble complexes with radionuclides and metals and has been used to decontaminate and process nuclear materials. Synthetic chelating agents were co-disposed with radionuclides (e.g., 60Co, Pu) and heavy metals enhancing their transport in the subsurface. An understanding of EDTA biodegradation is essential to help mitigate enhanced radionuclide transport by EDTA. The objective of this research is to develop fundamental data on factors that govern the biodegradation of radionuclide-EDTA. These factors include the dominant EDTA aqueous species, the biodegradation of various metal-EDTA complexes, the uptake of various metal-EDTA complexes into the cell, the distribution and mobility of the radionuclide during and after EDTA biodegradation, and the enzymology and genetics of EDTA biodegradation.

  19. Probing the Pu4 + magnetic moment in PuF4 with 19F NMR spectroscopy

    NASA Astrophysics Data System (ADS)

    Capan, Cigdem; Dempsey, Richard J.; Sinkov, Sergey; McNamara, Bruce K.; Cho, Herman

    2016-06-01

    The magnetic fields produced by Pu4 + centers have been measured by 19F NMR spectroscopy to elucidate the Pu-F electronic interactions in polycrystalline PuF4. Spectra acquired at applied fields of 2.35 and 7.05 T reveal a linear scaling of the 19F line shape. A model is presented that treats the line broadening and shifts as due to dipolar fields produced by Pu valence electrons in localized noninteracting orbitals. Alternative explanations for the observed line shape involving covalent Pu-F bonding, superexchange interactions, and electronic configurations with enhanced magnetic moments are considered.

  20. Sonochemical redox reactions of Pu(III) and Pu(IV) in aqueous nitric solutions.

    PubMed

    Virot, Matthieu; Venault, Laurent; Moisy, Philippe; Nikitenko, Sergey I

    2015-02-14

    The behavior of Pu(iv) and Pu(iii) was investigated in aqueous nitric solutions under ultrasound irradiation (Ar, 20 kHz). In the absence of anti-nitrous reagents, ultrasound has no effect on Pu(iv), while Pu(iii) can be rapidly oxidized to Pu(iv) due to the autocatalytic formation of HNO(2) induced by HNO(3) sonolysis. In the presence of anti-nitrous reagents (sulfamic acid or hydrazinium nitrate), Pu(iv) can be sonochemically reduced to Pu(iii). The reduction follows a first order reaction law and leads to a steady state where Pu(iv) and Pu(iii) coexist in solution. The reduction process is attributed to the sonochemical generation of H(2)O(2) in solution. The kinetics attributed to the reduction of Pu(iv) are however higher than those related to the formation of H(2)O(2) which, after several hypotheses, is explained by the sonochemical erosion of the titanium-based sonotrode. Titanium particles thereby generated can be solubilized under ultrasound and generate Ti(iii) as an intermediate species, a strong reducing agent able to react with Pu(iv).

  1. Experimental verification of modeling results for a PGNAA system for nondestructive assay of RCRA metals in drums

    PubMed

    Dulloo; Ruddy; Congedo; Seidel; McIlwain

    2000-10-01

    The use of pulsed gamma neutron activation analysis (PGNAA) for the nondestructive assay of mercury, cadmium and lead in a concrete matrix has been demonstrated. Calculations have also been performed to study interference with PGNAA detection sensitivity resulting from the presence of 238U, 235U, and 239Pu at levels expected in mixed waste. Analyses based on transport calculations examined the effects of these nuclides on neutron kinetics, and the contribution from the capture, fission and decay gamma-rays emitted by the nuclides to the gamma-ray spectrum. These calculations predicted insignificant effects on the system's detection limits (115, 9 and 4400 ppm for Hg, Cd and Pb, respectively, for a 2000 s assay). This paper describes verification measurements recently conducted using samples of 235U and 231U in the test drum geometry, which have provided experimental confirmation of the modeling results.

  2. Distribution of nuclear bomb Pu in Nishiyama area, Nagasaki, estimated by accurate and precise determination of 240Pu/239Pu ratio in soils.

    PubMed

    Yoshida, S; Muramatsu, Y; Yamazaki, S; Ban-Nai, T

    2007-01-01

    Plutonium isotopes in forest soils collected in Nishiyama area, Nagasaki, were successfully determined by high resolution inductively coupled plasma mass spectrometry after the treatment with a microwave decomposition system. The (240)Pu/(239)Pu atom ratios observed in the samples in the Nishiyama area were obviously lower than the range of the global fallout. The low ratios (minimum 0.032) observed in Nishiyama area indicated the influence of detonation of the Pu nuclear weapon in 1945. Since the area is contaminated also by global fallout, the (240)Pu/(239)Pu atom ratio can be more sensitive indicator of bomb-derived Pu than Pu activity concentration.

  3. Criticality evaluation for the storage of converter plates in drums

    SciTech Connect

    Hu, J.P.; Rorer, D.C.; Liu, H.B.

    1993-12-31

    A criticality safety evaluation was performed to support the temporary storage of 20%-enriched uranium converter plates for future use in the Brookhaven Medical Research Reactor (BMRR). A total of twelve such plates each containing approximately one kilogram of the {sup 235}U will be stored in DOT-certified 6M-drums, which have the same dimensions as standard 55-gallon drums except that they are twice as high (178.5cm). Each drum contains a Celotex liner surrounding a central 12.7cm-dia steel pipe. The plates have a nominal size of 0.3cm{times}l0.5cm{times}l25.7cm and fit inside the steel pipe, which extends 130cm in the axial direction. Because the accommodation of twelve plates in one drum is physically possible and more economical, this option for plate storage would be recommended provided that the criticality safety limit is not exceeded. In this paper, the neutron multiplication K{sub eff} in drums is calculated using the Monte Carlo Neutron and Photon Transport code (MCNP). For conservatism, several different configurations which could result.in the most reactive conditions for K{sub eff} have been examined. As part of the effort to optimize the arrangement of plates in drums, a second group of the MCNP calculations is performed using twelve plates evenly contained within two drums placed immediately adjacent to each other model again simulates the most reactive conditions for K{sub eff} estimations.

  4. Room-temperature electron spectroscopy of 239Pu and 240Pu

    NASA Astrophysics Data System (ADS)

    Ahmad, I.; Kondev, F. G.; Greene, J. P.; Zhu, S.

    2015-06-01

    Passivated, implanted, planar silicon (PIPS) detectors have been used for the measurement of electron spectra. The commercially available PIPS detectors, available in thicknesses of 100 μm, 300 μm, and 500 μm, have an energy resolution (FWHM) of ~ 2.2 keV, which is essentially the same as that of PIN diodes. Alpha and electron spectra of mass-separated 239Pu and 240Pu sources have been measured with a 300-μm thick PIPS detector and the electron to alpha ratios for the conversion lines of the 51.62- and 45.24-keV transitions have been determined. A procedure has been developed to determine the amount of 239Pu and 240Pu in a mixed source. The α-particle emission rate of the mixed source is measured, which is the sum of individual rates. From the electron spectrum of the mixed source, measured with the same setup as the alpha spectrum, the rates of 239Pu electron lines are determined. Using the electron rate of the 239Pu line and the electron to alpha ratio measured for the pure source, the α-particle emission rate of 239Pu is determined. The difference from the total α-particle emission rate gives the α-particle emission rate of 240Pu. In addition, electron intensities and conversion coefficients of the 239Pu and 240Pu transitions have been measured.

  5. Disposition of transuranic residues from plutonium isentropic compression experiment (Pu-ICE) constucted at Z machine

    SciTech Connect

    Goyal, Kapil K; French, David M; Humphrey, Betty J; Gluth, Jeffry

    2010-01-01

    In 1992, the U.S. Congress passed legislation to discontinue above- and below-ground testing of nuclear weapons. Because of this, the U.S. Department of Energy (DOE) must rely on laboratory experiments and computer-based calculations to verify the reliability of the nuclear stockpile. The Sandia National Laboratories/New Mexico (SNL/NM) Z machine was developed to support the science-based approach for mimicking nuclear explosions and stockpile stewardship. Plutonium (Pu) isotopes with greater than ninety-eight percent enrichment were used in the experiments. In May 2006, SNL/NM received authority that the Z Machine Isentropic Compression Experiments could commence. Los Alamos National Laboratory (LANL) provided the plutonium targets and loaded the target assemblies provided by SNL/NM. Three experiments were conducted from May through July 2006. The residues from each experiment, which weighed up to 913 pounds, were metallic and were packaged into a 55-gallon drum each. SNL/NM conducts the experiments and provides temporary storage for the drums until shipment to LANL for final waste certification for disposal at the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico. This paper presents a comprehensive approach for documenting generator knowledge for characterization of waste in cooperation with scientists at the two laboratories and addresses a variety of essential topics.

  6. Continuous mining machine and cutter drum drive therefor

    SciTech Connect

    Lebegue, M.K.

    1980-09-30

    A cutter drum member of a continuous mining machine is rotatably mounted on the front end of the machine. The drum member includes an intermediate section and a pair of canted end sections. Cutting elements extend from the surface of the respective drum sections and provide a continuous cutting pattern along the entire length of the drum member. Input drive shafts extend through rear openings between the adjacent ends of the intermediate section and the end sections. Rotation is transmitted from the input drive shafts through meshing bevel gears and planetary gears to rotate the intermediate section. The adjacent ends of the intermediate section and end sections include meshing gear teeth secured to the external surface of the sections so that the canted end sections are driven by the external meshing gear teeth. Passageways formed between the gear teeth on the external cylindrical surfaces of the drum sections facilitate the flow of dislodged material between the gear teeth to prevent material from accumulating between the teeth and thereby ensure positive drive to the canted end sections.

  7. Determination of 240Pu/239Pu atom ratio in seawaters from the East China Sea.

    PubMed

    Yamada, Masatoshi; Zheng, Jian

    2011-07-01

    The (240)Pu/(239)Pu atom ratios in seawater samples on the East China Sea continental shelf were measured. These ratios for surface and bottom waters had no significant difference. They were significantly higher than the average global fallout ratio of 0.18. It was proposed that the oceanic currents are accounted for delivery of close-in Pu from the Pacific Proving Grounds (PPG) to the studied areas. The contribution of the PPG close-in fallout was calculated to be 40 % on average. The (240)Pu/(239)Pu atom ratios should provide useful background data before the expected expansion of nuclear power capacity in East and South Asian countries and for distinguishing future sources of Pu.

  8. Brittle fractures of the drums of high-pressure boilers: Main causes and methods for preventing them

    NASA Astrophysics Data System (ADS)

    Grin', E. A.

    2008-02-01

    Factors causing damage to the metal of the drums of high-pressure boilers, as well as the known cases of drum failures, are analyzed. The totality of factors determining the operational reliability of drums is systematized. The process-related mechanism governing the destruction of the drums at the Kurgan cogeneration station and TETs-3 Yaroslavl cogeneration station, and the general factors caused these drums to fail are identified. Recommendations for reducing the risk of drum failures are formulated.

  9. Resonant Photoemission in f Electron Systems: Pu& Gd

    SciTech Connect

    Tobin, J G; Chung, B W; Schulze, R K; Terry, J; Farr, J D; Shuh, D K; Heinzelman, K; Rotenberg, E; Waddill, G D; van der Laan, G

    2003-03-07

    Resonant photoemission in the Pu5f and Pu6p states is compared to that in the Gd4f and Gd5p states. Spectral simulations, based upon and atomic model with angular momentum coupling, are compared to the Gd and Pu results. Additional spectroscopic measurements of Pu, including core level photoemission and x-ray absorption are also presented.

  10. Tread drum for animals. [having an electrical shock station

    NASA Technical Reports Server (NTRS)

    Howard, W. H. (Inventor)

    1978-01-01

    A device for exercising animals such as primates is described, which includes a cylindrical housing mounted for rotation about a horizontal axis of revolution and has a cylindrical treadway portion on which the animal treads while the drum is rotated by means of a motorized drive. The treadway portion of the drum includes an electrode structure with sectors being independently energizable by means of a commutator and source of potential so that an electrical shock station is created behind a running-in-place station on the moving treadway. In this manner, if the animal should fall behind its running-in-place station, it may be shocked by treading on the energized electrode structure. One end of the tread drum comprises a transparent wall for unobstructed viewing of the animal being exercised.

  11. Alternatives to reduce corrosion of carbon steel storage drums

    SciTech Connect

    Zirker, L.R.; Beitel, G.A.

    1995-11-01

    The major tasks of this research were (a) pollution prevention opportunity assessments on the overpacking operations for failed or corroded drums, (b) research on existing container corrosion data, (c) investigation of the storage environment of the new Resource Conservation and Recovery Act Type II storage modules, (d) identification of waste streams that demonstrate deleterious corrosion affects on drum storage life, and (e) corrosion test cell program development. Twenty-one waste streams from five US Department of Energy (DOE) sites within the DOE Complex were identified to demonstrate a deleterious effect to steel storage drums. The major components of these waste streams include acids, salts, and solvent liquids, sludges, and still bottoms. The solvent-based waste streams typically had the shortest time to failure: 0.5 to 2 years. The results of this research support the position that pollution prevention evaluations at the front end of a project or process will reduce pollution on the back end.

  12. Dose rate distribution from a standard waste drum arrangement.

    PubMed

    Zoeger, N; Brandl, A

    2011-11-01

    The evaluation of the dose rate distributions from radioactive sources, together with the specific detector locations with respect to those sources, in many cases presents a significant analytical challenge. With the exception of a few, simple source-detector geometries, it is not possible to find an analytical expression for these dose rate distributions as functions of detector location. In this paper, the dose rate distributions due to the arrangement of radiological waste drums on a standard wooden transport and storage pallet are investigated. The dose rates at various distances, ranging from 5 cm to 20 m, from the waste drum assembly have been evaluated by Monte Carlo calculations. The simulation data are fitted by smooth analytical functions in two independent regions, the waste drum near zone, where a logarithmic function best described the data, and the far zone, where the functional dependence closely approximates the 1/r2-law for point sources. PMID:21968820

  13. [Pu(IV) behavior in the serum].

    PubMed

    Surova, Z I

    1984-01-01

    This paper presents the results of studies of the hydrolysis and polymerization of Pu(IV) in blood serum. With nitrite Pu(IV) solutions incubated with blood serum 20-34% of the nuclide were precipitated as hydroxide and 11-36% converted into polymeric forms bound by high molecular weight proteins. For citrate solutions, these values were 3.8 and 3.0%, respectively. PMID:6505160

  14. Image data rate converter having a drum with a fixed head and a rotatable head

    NASA Technical Reports Server (NTRS)

    Billingsley, F. C. (Inventor)

    1973-01-01

    A data-rate converter is disclosed comprising a rotatable data-storing drum with at least one fixed read/record head and a rotatable read/record head. The latter is rotatable in a circular path about the drum axis of rotation. The drum is positionable in any one of a plurality of axial positions with respect to the heads, so that at least one drum track is aligned with the fixed head in one drum position and with the rotatable head in another drum position. When a track is aligned with the fixed head, data may be recorded therin or read out therefrom at a rate which is a function of drum rotation, while when aligned with the rotatable head, data may be recorded or read out at a rate which is a function of the rates and directions of rotation of both the drum and the head.

  15. Case studies of corrosion of mixed waste and transuranic waste drums

    SciTech Connect

    Kosiewicz, S.T.

    1993-12-01

    This paper presents three case studies of corrosion of waste drums at the Los Alamos National Laboratory (LANL). Corrosion was not anticipated by the waste generators, but occurred because of subtle chemical or physical mechanisms. In one case, drums of a cemented transuranic (TRU) sludge experienced general and pitting corrosion. In the second instance, a chemical from a commercial paint stripper migrated from its primary containment drums to chemically attack overpack drums made of mild carbon steel. In the third case, drums of mixed low level waste (MLLW) soil corroded drum packaging even though the waste appeared to be dry when it was placed in the drums. These case studies are jointly discussed as ``lessons learned`` to enhance awareness of subtle mechanisms that can contribute to the corrosion of radioactive waste drums during interim storage.

  16. Traveling wave of segregation in a highly filled rotating drum.

    PubMed

    Inagaki, Shio; Yoshikawa, Kenichi

    2010-09-10

    The dynamics of a segregation pattern for a granular mixture in a highly filled rotating drum were studied. A spontaneously segregated band pattern traveled laterally and was accompanied by the repeated creation of new bands near the center of the drum and annihilation at both of its ends. The presence of nearly stationary convection plays an essential role in causing this traveling wave. Based on direct observations of both the interior and the exterior of the segregation pattern, this spatiotemporal pattern is interpreted in terms of a one-dimensional Cahn-Hilliard equation by including the effect of stationary convection. PMID:20867609

  17. Cascade generalized predictive control strategy for boiler drum level.

    PubMed

    Xu, Min; Li, Shaoyuan; Cai, Wenjian

    2005-07-01

    This paper proposes a cascade model predictive control scheme for boiler drum level control. By employing generalized predictive control structures for both inner and outer loops, measured and unmeasured disturbances can be effectively rejected, and drum level at constant load is maintained. In addition, nonminimum phase characteristic and system constraints in both loops can be handled effectively by generalized predictive control algorithms. Simulation results are provided to show that cascade generalized predictive control results in better performance than that of well tuned cascade proportional integral differential controllers. The algorithm has also been implemented to control a 75-MW boiler plant, and the results show an improvement over conventional control schemes.

  18. Renewable Energy Opportunities at Fort Drum, New York

    SciTech Connect

    Brown, Scott A.; Orrell, Alice C.; Solana, Amy E.; Williamson, Jennifer L.; Hand, James R.; Russo, Bryan J.; Weimar, Mark R.; Rowley, Steven; Nesse, Ronald J.

    2010-10-20

    This document provides an overview of renewable resource potential at Fort Drum, based primarily upon analysis of secondary data sources supplemented with limited on-site evaluations. This effort focuses on grid-connected generation of electricity from renewable energy sources and also on ground source heat pumps for heating and cooling buildings. The effort was funded by the U.S. Army Installation Management Command (IMCOM) as follow-on to the 2005 Department of Defense (DoD) Renewables Assessment. The site visit to Fort Drum took place on May 4 and 5, 2010.

  19. The Spectroscopic Signature of Aging in (delta)-Pu(Ga)

    SciTech Connect

    Tobin, J G; Yu, S; Chung, B W

    2009-04-29

    The electronic structure of Pu is briefly discussed, with emphasis upon Aging effects. Photoelectron Spectroscopy and X-ray Absorption Spectroscopy have contributed greatly to our improved understanding of Pu electronic structure. (See Figure 1.) From these and related measurements, the following has been determined: (1) The Pu 5f spin-orbit splitting is large; (2) The number of Pu5f electrons is 5; and (3) The Pu 5f spin-orbit splitting effect dominates 5f itineracy.

  20. 49 CFR 178.506 - Standards for metal drums other than steel or aluminum.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... aluminum. 178.506 Section 178.506 Transportation Other Regulations Relating to Transportation (Continued... drums other than steel or aluminum. (a) The following are the identification codes for metal drums other than steel or aluminum: (1) 1N1 for a non-removable head metal drum; and (2) 1N2 for a removable...

  1. 49 CFR 178.506 - Standards for metal drums other than steel or aluminum.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... aluminum. 178.506 Section 178.506 Transportation Other Regulations Relating to Transportation (Continued... drums other than steel or aluminum. (a) The following are the identification codes for metal drums other than steel or aluminum: (1) 1N1 for a non-removable head metal drum; and (2) 1N2 for a removable...

  2. 49 CFR 178.506 - Standards for metal drums other than steel or aluminum.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... aluminum. 178.506 Section 178.506 Transportation Other Regulations Relating to Transportation (Continued... drums other than steel or aluminum. (a) The following are the identification codes for metal drums other than steel or aluminum: (1) 1N1 for a non-removable head metal drum; and (2) 1N2 for a removable...

  3. 49 CFR 178.506 - Standards for metal drums other than steel or aluminum.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... aluminum. 178.506 Section 178.506 Transportation Other Regulations Relating to Transportation (Continued... drums other than steel or aluminum. (a) The following are the identification codes for metal drums other than steel or aluminum: (1) 1N1 for a non-removable head metal drum; and (2) 1N2 for a removable...

  4. 49 CFR 178.506 - Standards for metal drums other than steel or aluminum.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... aluminum. 178.506 Section 178.506 Transportation Other Regulations Relating to Transportation PIPELINE AND... drums other than steel or aluminum. (a) The following are the identification codes for metal drums other than steel or aluminum: (1) 1N1 for a non-removable head metal drum; and (2) 1N2 for a removable...

  5. Reference drums used in calibration of a plastic scintillation counter in a 4π counting geometry.

    PubMed

    Yeh, Chin-Hsien; Yuan, Ming-Chen

    2016-03-01

    In this study, two kinds of reference drums were developed. One type was constructed with nine layers of large-area sources filled with different materials having five different densities. The other type of reference drums was constructed with nine rod sources filled with the same materials of different densities. The efficiency calibration of a plastic scintillation counter in 4π counting geometry using these two kinds of drums showed that rod-source drums resulted in higher counting efficiency than layered source drums. The counting rates obtained from rod-source drums were closer to those obtained from a standard drum with water solution than counting rates from drums with layered sources. The results of this study recommend to use reference drums with rod-sources to compensate the drawbacks of standard drums with water solution of not being able to adjust the density of material. The proposed reference drums improve the accuracy of radioactivity analysis for waste drums of different densities. PMID:26651167

  6. Analytical and experimental evaluation of solid waste drum fire performance volumes I and II

    SciTech Connect

    Hecker, C.F.,; Rhodes, B.T.; Beitel, J.J.; Gottuk, D.T.; Beyler, C.L.; Rosenbaum, E.R.,

    1995-04-28

    Fire hazards associated with drum storage of radioactively contaminated wastes are a major concern in DOE facilities design for long term storage of solid wastes in drums. These facilities include drums stored in pallet arrays and in rack storage systems. This report details testing in this area

  7. Specific Instructions Are Important for Continuous Bimanual Drumming in Adults with Down Syndrome

    ERIC Educational Resources Information Center

    Ringenbach, Shannon D.; Allen, Heather; Chung, Susan; Jung, Michelle L.

    2006-01-01

    The present study examined continuous and discrete bimanual drumming in response to different instructions in 10 adults with Down syndrome, 10 mental age-matched and 10 chronological age-matched groups. For continuous drumming, participants hit two drums with both hands at the same time following verbal (e.g., "up" and "down"), visual (e.g., video…

  8. How to Drum Up a Conversation in a Required Music Class.

    ERIC Educational Resources Information Center

    Hoffman, Barry Charles

    1994-01-01

    Describes activities in a secondary music class in which students communicate with talking drums. Maintains that the class project was developed during a teaching unit on the musical practices of the Ashanti ethnic group in Ghana. Includes instructions for making talking drums and four examples of orchestrating name rhythms for drums. (CFR)

  9. The Oral Tradition in the Sankofa Drum and Dance Ensemble: Student Perceptions

    ERIC Educational Resources Information Center

    Hess, Juliet

    2009-01-01

    The Sankofa Drum and Dance Ensemble is a Ghanaian drum and dance ensemble that focusses on music in the Ewe tradition. It is based in an elementary school in the Greater Toronto Area and consists of students in Grade 4 through Grade 8. Students in the ensemble study Ghanaian traditional Ewe drumming and dancing in the oral tradition. Nine students…

  10. Persons with and without Down Syndrome Use Similar Strategies when Using Visual Instructions for Bimanual Drumming

    ERIC Educational Resources Information Center

    Ringenbach, S. D. (Robertson); Mulvey, G. M.; Beachy, C.

    2007-01-01

    Background: Previous research suggested that persons with Down syndrome (DS) used a different strategy to drum than typical adults. Methods: The present study examined continuous bimanual drumming strategies in response to different instructions in 10 persons with DS, 10 mental age-matched and 10 chronological age-matched groups. The drumming task…

  11. 30 CFR 75.1403-3 - Criteria-Drum clutch; cage construction.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Criteria-Drum clutch; cage construction. 75... § 75.1403-3 Criteria—Drum clutch; cage construction. (a) The clutch of a free-drum on a personnel hoist should be provided with a locking mechanism or interlocked with the brake to prevent...

  12. 30 CFR 75.1403-3 - Criteria-Drum clutch; cage construction.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Criteria-Drum clutch; cage construction. 75... § 75.1403-3 Criteria—Drum clutch; cage construction. (a) The clutch of a free-drum on a personnel hoist should be provided with a locking mechanism or interlocked with the brake to prevent...

  13. 30 CFR 75.1403-3 - Criteria-Drum clutch; cage construction.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Criteria-Drum clutch; cage construction. 75... § 75.1403-3 Criteria—Drum clutch; cage construction. (a) The clutch of a free-drum on a personnel hoist should be provided with a locking mechanism or interlocked with the brake to prevent...

  14. 30 CFR 75.1403-3 - Criteria-Drum clutch; cage construction.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Criteria-Drum clutch; cage construction. 75... § 75.1403-3 Criteria—Drum clutch; cage construction. (a) The clutch of a free-drum on a personnel hoist should be provided with a locking mechanism or interlocked with the brake to prevent...

  15. 30 CFR 75.1403-3 - Criteria-Drum clutch; cage construction.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Criteria-Drum clutch; cage construction. 75... § 75.1403-3 Criteria—Drum clutch; cage construction. (a) The clutch of a free-drum on a personnel hoist... shaft sumps. (f) Workers should wear safety belts while doing work in or over shafts....

  16. JUSTIFICATION FOR A LIMIT OF 15 PERCENT HYDROGEN IN A 55 GALLON DRUM

    SciTech Connect

    MARUSICH, R.M.

    2007-01-04

    The concentration of 15% hydrogen in air in a waste drum is used as the concentration at which the drum remains intact in the case of a deflagration. The following describes what could happen to the drum if 15% hydrogen or more in air were ignited. Table 2 of the Savannah River report WSRC-TR-90-165 ''TRU Drum Hydrogen Explosion Tests'' provides the results of tests performed in 55-gallon drums filled with hydrogen and air mixtures. The hydrogen-air mixtures were ignited by a hot-wire igniter. The results of the tests are shown in Table 1. They concluded that drums can withstand deflagration involving hydrogen concentration up to 15% hydrogen. Testing was performed at Idaho Falls and documented in a letter from RH Beers, Waste Technology Programs Division, EG&G Idaho, to CP Gertz, Radioactive Waste Technology Branch, DOE dated Sept. 29, 1983. In these tests, 55-gallon drums were filled with hydrogen-air mixtures which were ignited. The results in Table 2.2 showed that ignition for drums containing 11% and 14% hydrogen, the drum lid remained on the drum. Ignition in drum with 30% hydrogen resulted in lid loss. It is concluded from the results of these two tests that, for uncorroded drums, a 15% hydrogen in air mixture will not result in loss of drum integrity (i.e., lid remains on, walls remain intact). The drum walls however, may be thinned due to corrosion. The effect of the deflagration on thinner walls is assessed next. Assume a 15% hydrogen in air mixture exists in a drum. The pressure assuming adiabatic isochoric complete combustion (AICC) conditions is 69 psig (using the same deflagration pressure calculation method as in HNF-19492, ''Revised Hydrogen Deflagration Analysis which got 82 psig for 20% hydrogen in air).

  17. Characterization of chaotic motion in a rotating drum

    NASA Astrophysics Data System (ADS)

    Davidheiser, James E.

    Numerous studies in the past have demonstrated the potential for geometrically simple fluid systems to produce complicated dynamical behavior. In particular, small collections of non-Brownian particles moving within viscous fluids can follow chaotic trajectories. In this work, we study a rotating drum filled with pure glycerol and three large, heavy particles. In studying these rotating drum systems, we have found a rich and varied phase space, made up of several previously unseen behaviors. With varying rotation rate, the particles can undergo straightforward cascading periodic behavior, and grouped periodic cascades we have labeled as doublet and triplet states. Furthermore, we find two regimes of qualitatively distinct chaotic behavior, with one type biased to either side of the drum, and the other lacking bias. The rotating drum experiment serves as a simple model system to demonstrate chaotic behavior in fluid dynamical systems. The existence of such model systems gives a baseline to which other systems can be compared and better understood, and our use of robust, easily implemented measurements serves as a straightforward comparison point which can be applied to various other chaotic fluid systems.

  18. Small-Scale Experiments.10-gallon drum experiment summary

    SciTech Connect

    Rosenberg, David M.

    2015-02-05

    A series of sub-scale (10-gallon) drum experiments were conducted to characterize the reactivity, heat generation, and gas generation of mixtures of chemicals believed to be present in the drum (68660) known to have breached in association with the radiation release event at the Waste Isolation Pilot Plant (WIPP) on February 14, 2014, at a scale expected to be large enough to replicate the environment in that drum but small enough to be practical, safe, and cost effective. These tests were not intended to replicate all the properties of drum 68660 or the event that led to its breach, or to validate a particular hypothesis of the release event. They were intended to observe, in a controlled environment and with suitable diagnostics, the behavior of simple mixtures of chemicals in order to determine if they could support reactivity that could result in ignition or if some other ingredient or event would be necessary. There is a significant amount of uncertainty into the exact composition of the barrel; a limited sub-set of known components was identified, reviewed with Technical Assessment Team (TAT) members, and used in these tests. This set of experiments was intended to provide a framework to postulate realistic, data-supported hypotheses for processes that occur in a “68660-like” configuration, not definitively prove what actually occurred in 68660.

  19. Middle School Drum Ensemble: An Unlikely Experience in Classroom Democracy

    ERIC Educational Resources Information Center

    Barbre, James

    2013-01-01

    Though music has a long and successful history within education, it is often one of the first sacrificial lambs when school budgets tighten. Over the course of an academic year, a documentary film sought to tell the story of an American middle school drum ensemble. The context of this group provided an ideal way to examine the nature of student…

  20. DRUMS: a human disease related unique gene mutation search engine.

    PubMed

    Li, Zuofeng; Liu, Xingnan; Wen, Jingran; Xu, Ye; Zhao, Xin; Li, Xuan; Liu, Lei; Zhang, Xiaoyan

    2011-10-01

    With the completion of the human genome project and the development of new methods for gene variant detection, the integration of mutation data and its phenotypic consequences has become more important than ever. Among all available resources, locus-specific databases (LSDBs) curate one or more specific genes' mutation data along with high-quality phenotypes. Although some genotype-phenotype data from LSDB have been integrated into central databases little effort has been made to integrate all these data by a search engine approach. In this work, we have developed disease related unique gene mutation search engine (DRUMS), a search engine for human disease related unique gene mutation as a convenient tool for biologists or physicians to retrieve gene variant and related phenotype information. Gene variant and phenotype information were stored in a gene-centred relational database. Moreover, the relationships between mutations and diseases were indexed by the uniform resource identifier from LSDB, or another central database. By querying DRUMS, users can access the most popular mutation databases under one interface. DRUMS could be treated as a domain specific search engine. By using web crawling, indexing, and searching technologies, it provides a competitively efficient interface for searching and retrieving mutation data and their relationships to diseases. The present system is freely accessible at http://www.scbit.org/glif/new/drums/index.html.

  1. Support for transmission shaft and hydraulic servo drum

    SciTech Connect

    Kobayashi, K.; Sumiya, K.; Taga, Y.; Watanabe, K.

    1987-09-15

    In a support for use in an automatic transmission apparatus of the type having a transmission shaft for transmitting power, an annular hydraulic servo drum and a piston fitted in the hydraulic servo drum for engaging and disengaging a friction engaging means is described, wherein the support has an axially extending tubular supporting portion having an inner peripheral surface for supporting the transmission shaft, an outer peripheral surface for supporting an inner cylindrical portion of the hydraulic servo drum, and working oil passages formed and adapted for supplying and discharging a working oil to and from the hydraulic servo drum. The improvement consists of: a support body made of light material having a first radially extending oil passage leading from an oil pressure controller for supplying and discharging a working oil and communicating with the inner peripheral surface of the tubular supporting portion; an inner sleeve of a heavier material than the support body fitting on the inner peripheral surface of the tubular supporting portion to cover the inner axially extending oil groove thereby forming an oil passage for working oil; and an outer sleeve of a heavier material than the support body fitting on the outer peripheral surface of the tubular supporting portion.

  2. The Way of the Drum: When Earth Becomes Heart.

    ERIC Educational Resources Information Center

    Antone, Grafton; Turchetti, Lois Provost

    Two Native people describe their respective journeys to healing, journeys that involved the rediscovery of language and culture. In Part I, "Healing the Tears of Yesterday by the Drum Today: The Oneida Language Is a Healing Medicine" (Grafton Antone), the first narrator taught the Oneida language to adult students at a community center. Lacking…

  3. 3. VIEW TO NORTHEAST, NORTH SIDE OF CENTER DRUM MACHINERY ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. VIEW TO NORTHEAST, NORTH SIDE OF CENTER DRUM MACHINERY ROOM. MOTOR #1 COMPARTMENT IN REAR, AUXILIARY MOTOR DRIVE SHAFT, POWER PANELS ON BACK OF AUXILIARY MOTOR HOUSE. BRIDGE DECK FRAMING ABOVE. - Burlington Northern Railroad Bridge, Spanning Willamette River at River Mile 6.9, Portland, Multnomah County, OR

  4. 49 CFR 178.507 - Standards for plywood drums.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS SPECIFICATIONS FOR... effectiveness of the drum for the purpose intended. A material other than plywood, of at least equivalent strength and durability, may be used for the manufacture of the heads. (2) At least two-ply plywood must...

  5. 7 CFR 1434.8 - Containers and drums.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REGULATIONS FOR HONEY § 1434.8 Containers and drums. (a)(1) To be eligible for assistance under this part, honey must be packed in: (i) CCC-approved, 5-gallon plastic containers; (ii) 5-gallon metal containers... Intermediate Bulk Containers (IBC's). (2) Honey stored in plastic containers must be determined safe and...

  6. Flow Straightener for a Rotating-Drum Liquid Separator

    NASA Technical Reports Server (NTRS)

    O'Coin, James R.; Converse, David G.; Rethke, Donald W.

    2004-01-01

    A flow straightener has been incorporated into a rotary liquid separator that originally comprised an inlet tube, a shroud plate, an impeller, an inner drum, an outer drum, a housing, a pitot tube, and a hollow shaft motor. As a consequence of the original geometry of the impeller, shroud, inner drum, and hollow shaft, swirl was created in the airflow inside the hollow shaft during operation. The swirl speed was large enough to cause a significant pressure drop. The flow straightener consists of vanes on the back side of the shroud plate. These vanes compartmentalize the inside of the inner drum in such a way as to break up the flow path and thereby stop the air from swirling; as a result, the air enters the hollow shaft with a predominantly axial velocity instead of a swirl. Tests of the rotary liquid separator at an airflow rate of 10 cu ft/min (0.0047 cu m/s) revealed that the dynamic pressure drop was 8 in. of water (approx.=2 kPa) in the absence of the flow straightener and was reduced to 1 in. of water (approx.=0.25 kPa) in the presence of the flow straightener.

  7. Comparative Analysis of Cherenkov Light Detectors in an Oil Drum

    NASA Astrophysics Data System (ADS)

    Niduaza, Rexavalmar; Wedel, Zachary; Castro, Juan; Zavala, Favian; Fan, Sewan; Fatuzzo, Laura

    2014-03-01

    The multi-pixel photon counters (MPPC) has been used in a number of research development in astro-particle physics and particle physics. In an effort to further implement the MPPC detector, we constructed a modular experimental setup using a 16-inch tall acrylic cylinder filled with distilled water as the light producing medium to determine its feasibility as a possible detector for weak Cherenkov light. We have since progressed towards utilizing an oil drum (approximately 30 gallons) as our light-tight container replacing our prototype. In this talk, we would discuss the results regarding our investigation utilizing 1-inch and 3-inch photo-multiplier tubes (PMTs) in an oil drum as we did for our prototype. We would also present our experimental findings comparing our prototype and our oil drum setup using PMTs in coincidence with the MPPC coupled with wavelength-shifting fibers that are submerged in distilled water inside the oil drum vessel. Department of Education grant nymber P031S90007.

  8. Development of Interpersonal Coordination between Peers during a Drumming Task

    ERIC Educational Resources Information Center

    Endedijk, Hinke M.; Ramenzoni, Veronica C. O.; Cox, Ralf F. A.; Cillessen, Antonius H. N.; Bekkering, Harold; Hunnius, Sabine

    2015-01-01

    During social interaction, the behavior of interacting partners becomes coordinated. Although interpersonal coordination is well-studied in adults, relatively little is known about its development. In this project we explored how 2-, 3-, and 4-year-old children spontaneously coordinated their drumming with a peer. Results showed that all children…

  9. Memory Drum Theory's C Movement: Revelations from Franklin Henry

    ERIC Educational Resources Information Center

    Fischman, Mark G.; Christina, Robert W.; Anson, J. Greg

    2008-01-01

    Franklin Henry's "memory drum" theory of neuromotor reaction (Henry & Rogers, 1960) was one of the most influential studies of the response programming stage of information processing. The paper is the most-cited study ever published in the "Research Quarterly for Exercise and Sport." However, few people know there is a noteworthy error in the…

  10. 49 CFR 178.508 - Standards for fiber drums.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... body of the drum must be constructed of multiple plies of heavy paper or fiberboard (without..., waxed kraft paper, metal foil, plastic material, or similar materials. (2) Heads must be of natural wood, fiberboard, metal, plywood, plastics, or other suitable material and may include one or more...

  11. Chemical potential of oxygen in (U, Pu) mixed oxide with Pu/(U+Pu) = 0.46

    NASA Astrophysics Data System (ADS)

    Dawar, Rimpi; Chandramouli, V.; Anthonysamy, S.

    2016-05-01

    Chemical potential of oxygen in (U,Pu) mixed oxide with Pu/(U + Pu) = 0.46 was measured for the first time using H2/H2O gas equilibration combined with solid electrolyte EMF technique at 1073, 1273 and 1473 K covering an oxygen potential range of -525 to -325 kJ mol-1. The effect of oxygen potential on the oxygen to metal ratio was determined. Increase in oxygen potential increases the O/M. In this study the minimum O/M obtained was 1.985 below which reduction was not possible. Partial molar enthalpy ΔHbar O2 and entropy ΔSbar O2 of oxygen were calculated from the oxygen potential data. The values of -752.36 kJ mol-1 and 0.25 kJ mol-1 were obtained for ΔHbar O2 and ΔSbar O2 respectively.

  12. Prompt fission γ -ray spectrum characteristics from 240Pu(sf ) and 242Pu(sf )

    NASA Astrophysics Data System (ADS)

    Oberstedt, S.; Oberstedt, A.; Gatera, A.; Göök, A.; Hambsch, F.-J.; Moens, A.; Sibbens, G.; Vanleeuw, D.; Vidali, M.

    2016-05-01

    In this paper we present first results for prompt fission γ -ray spectra (PFGS) characteristics from the spontaneous fission (sf) of 240Pu and 242Pu. For 242Pu(sf ) we obtained, after proper unfolding of the detector response, an average energy per photon ɛ¯γ=(0.843 ±0.012 ) MeV, an average multiplicity M¯γ=(6.72 ±0.07 ) , and an average total γ -ray energy release per fission E¯γ ,tot = (5.66 ± 0.06) MeV. The 240Pu(sf ) emission spectrum was obtained by applying a so-called detector-response transformation function determined from the 242Pu spectrum measured in exactly the same geometry. The results are an average energy per photon ɛ¯γ=(0.80 ±0.07 ) MeV, the average multiplicity M¯γ = (8.2 ± 0.4), and an average total γ -ray energy release per fission E¯γ ,tot = (6.6 ± 0.5) MeV. The PFGS characteristics for 242Pu(sf ) are in very good agreement with those from thermal-neutron-induced fission on 241Pu and scales well with the corresponding prompt neutron multiplicity. Our results in the case of 240Pu(sf ), although drawn from a limited number of events, show a significantly enhanced average multiplicity and average total energy, but may be understood from a different fragment yield distribution in 240Pu(sf ) compared to that of 242Pu(sf ).

  13. Measurement of the U-235 Content of Concreted Waste Drums

    SciTech Connect

    Rackham, J.; Hughes, K.; Oldeide, R.; Sharpe, J.; Morgan, S.

    2008-07-01

    A challenging assay situation recently arose, whereby the fissile (i.e. total plutonium plus U-235) content of a population of 164 historical waste drums containing concrete needed to be measured, to comply with nuclear safety limits for transport to, and interim storage within, an Engineered Drum Store. BIL Solutions Ltd has developed a new methodology for measurement of the U-235 content of these 'concrete' drums, because the approach normally used by the in-situ Drum Monitors was found to be overly pessimistic. Initial investigations indicated significant quantities of uranium were present in these drums (but negligible plutonium), mixed with Np-237 and / or Ra-226. These initial measurements also indicated that the uranium was likely to be depleted in enrichment. The U-235 content was therefore determined by measuring the U-238 mass via the passive coincident neutron emission, and combining this with the U-235 and U-238 isotopic abundances, obtained by analysis of a gamma spectrum. Of the uranium isotopic analysis codes available, the FRAM (Fixed energy, Response function Analysis with Multiple efficiencies) software was selected as being most suitable for this application. A wide gamma-ray energy range is used (i.e. 120 keV to 1200 keV) which was considered more likely to yield results when there is significant attenuation. The software is also user configurable, enabling interferences from the other radionuclides present (i.e. Np-237 and Ra-226) to be accounted for. A series of test measurements were performed with well-characterised uranium sources attenuated by concrete shielding, to gain confidence in the performance of FRAM under such conditions. These test measurements indicated that FRAM was able to correctly determine the enrichment of heavily shielded uranium. The new U-235 measurement methodology was then applied to the population of concrete drums; successfully yielding U-235 results despite the dense waste matrix and significant interference from

  14. Redefining design criteria for Pu-238 gloveboxes

    SciTech Connect

    Acosta, S.V.

    1998-12-31

    Enclosures for confinement of special nuclear materials (SNM) have evolved into the design of gloveboxes. During the early stages of glovebox technology, established practices and process operation requirements defined design criteria. Proven boxes that performed and met or exceeded process requirements in one group or area, often could not be duplicated in other areas or processes, and till achieve the same success. Changes in materials, fabrication and installation methods often only met immediate design criteria. Standardization of design criteria took a big step during creation of ``Special-Nuclear Materials R and D Laboratory Project, Glovebox standards``. The standards defined design criteria for every type of process equipment in its most general form. Los Alamos National Laboratory (LANL) then and now has had great success with Pu-238 processing. However with ever changing Environment Safety and Health (ES and H) requirements and Ta-55 Facility Configuration Management, current design criteria are forced to explore alternative methods of glovebox design fabrication and installation. Pu-238 fuel processing operations in the Power Source Technologies Group have pushed the limitations of current design criteria. More than half of Pu-238 gloveboxes are being retrofitted or replaced to perform the specific fuel process operations. Pu-238 glovebox design criteria are headed toward process designed single use glovebox and supporting line gloveboxes. Gloveboxes that will house equipment and processes will support TA-55 Pu-238 fuel processing needs into the next century and extend glovebox expected design life.

  15. 239+240Pu concentration and isotope ratio (240Pu/239Pu) in aerosols during high dust (Yellow Sand) period, Korea.

    PubMed

    Choi, Man Sik; Lee, Dong-Soo; Choi, Jae-Cheon; Cha, Hyun-Ju; Yi, Hee-Il

    2006-10-15

    Concentration and isotope ratio of Pu were analyzed for aerosols collected at Anmyeondo located in the western coast of Korea using multiple collector inductively coupled plasma mass spectrometer equipped with desolvated micro-concentric nebulizer. Aerosols were collected from June 2001 to April 2002 using high volume air sampler. The samples consist of high dust samples (Yellow Sand), and also low dust samples; maximum Al concentration was 74.2 microg/m(3) and minimum was 0.17 microg/m(3). Pu was concentrated using 0.1 ml TEVA resin columns after conc. HNO(3) extraction. Isotope dilution using (242)Pu spike and mass bias correction using (233)U and (236)U mixed solution enabled the quantification of Pu and measurement of isotope ratio simultaneously. The contribution of (238)U from both spikes and samples was minimized by careful chemical separation and optimization of spike concentration. The (238)U(1)H and tail contribution on (239)Pu peak were about 0.75 x 10(-5) and 1 x 10(-5) of (238)U intensity, respectively, and they were corrected from (239)Pu using externally determined ((238)U(1)H + tailing)/(238)U ratio and (238)U measurement during acquisition. The detection limits of this analytical procedure were 0.61 fg/ml and 0.56 fg/ml for (239)Pu and (240)Pu, respectively (4 nBq/m(3) and 12 nBq/m(3) for (239)Pu and (240)Pu, respectively). The precision of isotope ratio measurement was better than 2% for larger quantity than 20 fg of (239)Pu. In spring, maximum concentration of 0.580 microBq/m(3) for (239)Pu and 0.404 microBq/m(3) for (240)Pu was observed when Al concentration was maximum, so called as Yellow Sand event. Pu concentrations in aerosols are well correlated with Al, a tracer of soil dust. The ratios of Pu/Al were 0.0082 (microBq/microg) and 0.0055 (microBq/microg) for (239)Pu/Al and (240)Pu/Al, respectively. Isotope ratios of Pu ((240)Pu/(239)Pu) in Yellow Sand samples show 0.191+/-0.014 close to those of global fallout. These facts indicate that

  16. The drum is the shaman, the spear guides his voice.

    PubMed

    Hoskins, J

    1988-01-01

    Kodi rituals of curing use anthropomorphized objects--the drum and the spear--as intermediaries to communicate with the spirits causing the affliction. The spear 'cuts through' to the cause of the illness at the divination, by guiding the arm and voice of the human diviner. The drum beaten during an all night ceremony has a more important role: a myth at the opening of the ceremony tells the drum's personal story or biography, which is identified with the suffering patient. In the course of the ceremony it travels on a shamanistic journey to the upperworld to seek the blessings of health and well-being. The myth of the drum's origin provides a narrative structure for the whole ritual, and defines the basis for its efficacy. The percussive sounds of the drum and gongs are said to make the patient feel better. A case study shows how 'ordered sound' is used to dissolve social tensions into a culturally structured pattern, so that consensus can be achieved in implicit accommodations in which neither party loses face. An older man's illness awakens guilty feelings among his younger relatives, whose thieving is believed to be responsible. The healing ritual creates the context for them to express contrition without confessing. Thus, although the rite re-establishes communication between persons and between the human and spirit worlds, it involves deception and silences as well as revelations. Through an analytic comment on social tensions, artistic illusions are used to overcome the airing of social differences. The healing rite is intended to restore a social consensus, produced by a combination of music, speech and actions, which allow signs to triumph over substance.

  17. Improvement of non-destructive fissile mass assays in α low-level waste drums: A matrix correction method based on neutron capture gamma-rays and a neutron generator

    NASA Astrophysics Data System (ADS)

    Jallu, F.; Loche, F.

    2008-08-01

    Within the framework of radioactive waste control, non-destructive assay (NDA) methods may be employed. The active neutron interrogation (ANI) method is now well-known and effective in quantifying low α-activity fissile masses (mainly 235U, 239Pu, 241Pu) with low densities, i.e. less than about 0.4, in radioactive waste drums of volumes up to 200 l. The PROMpt Epithermal and THErmal interrogation Experiment (PROMETHEE [F. Jallu, A. Mariani, C. Passard, A.-C. Raoux, H. Toubon, Alpha low level waste control: improvement of the PROMETHEE 6 assay system performances. Nucl. Technol. 153 (January) (2006); C. Passard, A. Mariani, F. Jallu, J. Romeyer-Dherber, H. Recroix, M. Rodriguez, J. Loridon, C. Denis, PROMETHEE: an alpha low level waste assay system using passive and active neutron measurement methods. Nucl. Technol. 140 (December) (2002) 303-314]) based on ANI has been under development since 1996 to reach the incinerating α low level waste (LLW) criterion of about 50 Bq[α] per gram of crude waste (≈50 μg Pu) in 118 l drums on the date the drums are conditioned. Difficulties arise when dealing with matrices containing neutron energy moderators such as H and neutron absorbents such as Cl. These components may have a great influence on the fissile mass deduced from the neutron signal measured by ANI. For example, the calibration coefficient measured in a 118 l drum containing a cellulose matrix (density d = 0.144 g cm -3) may be 50 times higher than that obtained in a poly-vinyl-chloride matrix ( d = 0.253 g cm -3). Without any information on the matrix, the fissile mass is often overestimated due to safety procedures and by considering the most disadvantageous calibration coefficient corresponding to the most absorbing and moderating calibration matrix. The work discussed in this paper was performed at the CEA Nuclear Measurement Laboratory in France. It concerns the development of a matrix effect correction method, which consists in identifying and quantifying

  18. Environmental conditions in water storage drums and influences on Aedes aegypti in Trinidad, West Indies.

    PubMed

    Hemme, Ryan R; Tank, Jennifer L; Chadee, Dave D; Severson, David W

    2009-10-01

    Water storage drums are often a primary breeding site for Aedes aegypti in developing countries. Habitat characteristics can impact both adult and larval fitness and survival, which may potentially influence arbovirus transmission. Our objective was to compare fundamental environmental differences in water drums based on the presence or absence of larvae in Trinidad. Drums were categorized according to the larval status, and if the drum was constructed of steel or plastic. Water samples were analyzed for ammonium, nitrate, and soluble reactive phosphorus (SRP). Continuous surface water temperatures were also recorded. Nutrient concentrations were considerably lower than those reported for other container breeding mosquitoes. No nutrient measured differed in concentration between drums positive compared to those that were negative for the presence of A. aegypti larvae. Levels of SRP and ammonium in steel drums were significantly lower than in plastic water drums. Both maximum and minimum surface temperatures were significantly lower in drums positive for the presence of larvae than in drums without larvae. Water temperatures in March and May were warmer than during October sampling periods. Larval presence is likely dependent upon the interaction among multiple biotic and abiotic factors. Despite appearance, not all water storage drums are equally suitable for A. aegypti development. Exposing water storage drums to direct sunlight or increased heat may be used in conjunction with sealing containers to reduce production of A. aegypti when draining and chemical treatment are impractical.

  19. Knockdown of PU.1 AS lncRNA inhibits adipogenesis through enhancing PU.1 mRNA translation.

    PubMed

    Pang, Wei-Jun; Lin, Li-Gen; Xiong, Yan; Wei, Ning; Wang, Yu; Shen, Qing-Wu; Yang, Gong-She

    2013-11-01

    PU.1 is an Ets family transcription factor involved in the myelo-lymphoid differentiation. We have previously demonstrated that PU.1 is also expressed in the adipocyte lineage. However, the expression levels of PU.1 mRNA and protein in preadipocytes do not match the levels in mature adipocytes. PU.1 mRNA level is higher in preadipocytes, whereas its protein is expressed in the adipocytes but not in the preadipocytes. The underlying mechanism remains elusive. Here, we find that miR-155 knockdown or overexpression has no effect on the levels of PU.1 mRNA and protein in preadipocytes or adipocytes. MiR-155 regulates adipogenesis not through PU.1, but via C/EBPβ which is another target of miR-155. We also checked the expression levels of PU.1 mRNA and antisense long non-coding RNA (AS lncRNA). Interestingly, compared with the level of PU.1 mRNA, the level of PU.1 AS lncRNA is much higher in preadipocytes, whereas it is opposite in the adipocytes. We further discover that PU.1 AS lncRNA binds to its mRNA forming an mRNA/AS lncRNA compound. The knockdown of PU.1 AS by siRNA inhibits adipogenesis and promotes PU.1 protein expression in both preadipocytes and adipocytes. Furthermore, the repression of PU.1 AS decreases the expression and secretion of adiponectin. We also find that the effect of retroviral-mediated PU.1 AS knockdown on adipogenesis is consistent with that of PU.1 AS knockdown by siRNA. Taken together, our results suggest that PU.1 AS lncRNA promotes adipogenesis through preventing PU.1 mRNA translation via binding to PU.1 mRNA to form mRNA/AS lncRNA duplex in preadipocytes.

  20. Oxidation behaviour of plutonium rich (U, Pu)C and (U, Pu)O2

    NASA Astrophysics Data System (ADS)

    Sali, S. K.; Kulkarni, N. K.; Phatak, Rohan; Agarwal, Renu

    2016-10-01

    Oxidation behaviour of (U0.3Pu0.7)C1.06 was investigated in air by heating samples up to 1073 K and 1273 K. Thermogravimetry (TG) of the samples and X-ray powder diffraction (XRD) of the intermediate products were used to understand the phenomenon taking place during this process. Theoretical calculations were carried out to understand the multiple phase changes taking place during oxidation of carbide. Theoretical results were validated by XRD analysis of the products obtained at different stages of oxidation. The final oxidized products were found to be a single FCC phase with O/M = 2.15 (M = U + Pu). Oxidation kinetic studies of (U0.3Pu0.7)O2 and (U0.47Pu0.53)O2 were carried out in dry air, using thermogravimetry, under non-isothermal conditions. The activation energy of oxidation was found to be 49 and 70 kJ/mol, respectively. Lattice parameter dependence on Pu/M and O/M of plutonium rich mixed oxide (MOX) was established using combined results of XRD and TG analysis of (U0.3Pu0.7)O2+x and (U0.47Pu0.53)O2+x.

  1. Isochronal Annealing Studies in Pu and Pu Alloys Using Magnetic Susceptibility

    SciTech Connect

    McCall, S. K.; Fluss, M. J.; Chung, B. W.; McElfresh, M. W.; Chapline, G.F.; Jackson, D. D.; Haire, Richard {Dick} G

    2007-01-01

    The isochronal annealing of the low temperature accumulated damage from the radioactive decay of plutonium in {alpha}-Pu, {delta}-Pu{sub 1-x}Ga{sub x} (x = 0.043) and {delta}-Pu{sub 1-x}Am{sub x} (x = 0.224) was characterized using magnetic susceptibility. In each specimen, thermal annealing, as tracked by magnetic susceptibility, only commenced when T > 33 K and the magnetic susceptibility changes due to defects were fully annealed at T not, vert, similar 300 K. The {alpha}-Pu magnetic susceptibility isochronal annealing data is similar to earlier measurements of resistivity characterized isochronal annealing. However, the {delta}-Pu{sub 1-x}Ga{sub x} (x = 0.043) magnetic susceptibility isochronal annealing data, when compared with similar resistivity data, indicates that for this alloy magnetic susceptibility studies are more sensitive to vacancies than to the interstitials accumulated at low temperatures. The Pu{sub 1-x}Am{sub x} (x = 0.224) alloy shows a remarkable change in properties, over a limited temperature range beginning where interstitial defects are first mobile, and characterized by an induced effective moment of order 1.1 {mu}{sub B}/Pu. This transient behavior may be evidence for a disorder driven low temperature phase transition, perhaps indicative of a compositional and structural proximity to a state possessing significant magnetic moments.

  2. $sup 238$Pu fuel form activities

    SciTech Connect

    Not Available

    1987-06-01

    This report for STYPu Fuel Form Activities has one main section: SRP-PuFF Facility. The SRL portion of this program has been completed. The program status, budget information, and milestone schedules are discussed. The SRP portion of this report summarizes production of STYPuO2 fuel forms for use in radioisotopic thermoelectric generators (RTG's) in the Plutonium Fuel Form (Puff) Facility at the Savannah River Plant. The PuFF Facility has been placed in a production readiness mode of operation pending funding of additional heat source programs.

  3. Plutonium diffusion in advanced fuels (U,Pu)(C,O) and (U,Pu)(C,N)

    SciTech Connect

    Bradbury, M.H.; Matzke, H.

    1983-07-01

    The self-diffusion of /sup 238/Pu was measured in an oxicarbide (U,Pu)(C,O) and a carbonitride (U,Pu) (C,N). The activation enthalpies were 447 and 347 kJ mol/sup -1/, respectively. The carbonitrides were confirmed to fall into three classes: carbide-like compositions with less than 30% nitrogen in the metalloid lattice, nitride-like composition with more than 70% nitrogen and with reduced atomic mobilities, and carbonitrides with about 50% nitrogen showing an intermediate behavior. The oxicarbide showed diffusion coefficients slightly larger than those of pure carbides.

  4. Pu-238 fuel form activities, January 1-31, 1985

    SciTech Connect

    Not Available

    1985-07-01

    This monthly report summarizes production of /sup 238/PuO/sub 2/ fuel forms for use in radioisotopic thermoelectric generators (RTG's) in the Plutonium Fuel Form (PuFF) Facility at the Savannah River Plant.

  5. Experimental Benchmarking of Pu Electronic Structure

    SciTech Connect

    Tobin, J G; Moore, K T; Chung, B W; Wall, M A; Schwartz, A J; Ebbinghaus, B B; Butterfield, M T; Teslich, Jr., N E; Bliss, R A; Morton, S A; Yu, S W; Komesu, T; Waddill, G D; der Laan, G v; Kutepov, A L

    2005-10-13

    The standard method to determine the band structure of a condensed phase material is to (1) obtain a single crystal with a well defined surface and (2) map the bands with angle resolved photoelectron spectroscopy (occupied or valence bands) and inverse photoelectron spectroscopy (unoccupied or conduction bands). Unfortunately, in the case of Pu, the single crystals of Pu are either nonexistent, very small and/or having poorly defined surfaces. Furthermore, effects such as electron correlation and a large spin-orbit splitting in the 5f states have further complicated the situation. Thus, we have embarked upon the utilization of unorthodox electron spectroscopies, to circumvent the problems caused by the absence of large single crystals of Pu with well-defined surfaces. Our approach includes the techniques of resonant photoelectron spectroscopy [1], x-ray absorption spectroscopy [1,2,3,4], electron energy loss spectroscopy [2,3,4], Fano Effect measurements [5], and Bremstrahlung Isochromat Spectroscopy [6], including the utilization of micro-focused beams to probe single-crystallite regions of polycrystalline Pu samples. [2,3,6

  6. Experimental Benchmarking of Pu Electronic Structure

    SciTech Connect

    Tobin, J.G.; Moore, K.T.; Chung, B.W.; Wall, M.A.; Schwartz, A.J.; Ebbinghaus, B.B.; Butterfield, M.T.; Teslich, Jr., N.E.; Bliss, R.A.; Morton, S.A.; Yu, S.W.; Komesu, T.; Waddill, G.D.; van der Laan, G.; Kutepov, A.L.

    2008-10-30

    The standard method to determine the band structure of a condensed phase material is to (1) obtain a single crystal with a well defined surface and (2) map the bands with angle resolved photoelectron spectroscopy (occupied or valence bands) and inverse photoelectron spectroscopy (unoccupied or conduction bands). Unfortunately, in the case of Pu, the single crystals of Pu are either nonexistent, very small and/or having poorly defined surfaces. Furthermore, effects such as electron correlation and a large spin-orbit splitting in the 5f states have further complicated the situation. Thus, we have embarked upon the utilization of unorthodox electron spectroscopies, to circumvent the problems caused by the absence of large single crystals of Pu with well-defined surfaces. Our approach includes the techniques of resonant photoelectron spectroscopy, x-ray absorption spectroscopy, electron energy loss spectroscopy, Fano Effect measurements, and Bremstrahlung Isochromat Spectroscopy, including the utilization of micro-focused beams to probe single-crystallite regions of polycrystalline Pu samples.

  7. Pu-238 fuel form activities, June 1-30, 1980

    SciTech Connect

    Not Available

    1980-07-18

    This monthly report for Pu-238 Fuel Form Activities has two main sections: SRP-PuFF Pu-238 Fuel Form Production Processes and SRL Pu-238 Fuel Form Research and Development. The program status, budget information, and milestone information are discussed in each main section. The Work Breakdown Structures (WBS) for this program is outlined. Only one monthly report per year is processed for EDB.

  8. The 239 Pu(n,2n)238Pu cross section: preliminary calculations

    SciTech Connect

    Chen, H; Reffo, G; Ross, M A; White, R M

    1999-03-12

    The primary motivation for the present work is to provide theoretical values for the ratio of the partial 239Pu(n,2nx{gamma})238Pu to total 239 Pu(n,2n)238Pu cross section for several discrete gamma transitions. Results and conclusions of preliminary calculations from threshold to 20 MeV are presented. Calculations are based on theoretical models with parameters obtained from the literature or from our ad hoc systematics. Optical model cross sections and transmission coefficients were determined using the coupled-channels method. The calculations included a preequilibrium component followed by multiple particle and gamma-ray emissions. Fission competition was included at all stages of de-excitation. Suggestions for further verifications and possible improvements are provided.

  9. Design and fabrication of 55-gallon drum shuffler standards

    SciTech Connect

    Long, S.M.; Hsue, F.; Hoth, C.; Fernandez, R.; Bjork, C.; Sprinkle, J.

    1994-08-01

    To analyze waste with varying levels of nuclear material, suitable standards are needed to calibrate analytical instrumentation. At the Los Alamos Plutonium Facility, the authors have designed and fabricated a single drum standard for a passive-active neutron counter (shuffler). The standard is modified simply by adding or subtracting plutonium of uranium cylinders to adapt to a range of nuclear material. The plutonium or uranium oxide was placed into small cylindrical containers (1-in. diameter by 5-in. long) and diluted with diatomaceous earth. The cylinders were welded closed and removed from the glove box environment without any external contamination. The containers were leak tested and then placed on a segmented gamma scanner to assure homogeneous distribution of the nuclear material. The cylinders are now placed into the drum to achieve the needed ranges for calibration of the instruments.

  10. Low tension graphene drums for electromechanical pressure sensing

    NASA Astrophysics Data System (ADS)

    Patel, Raj N.; Mathew, John P.; Borah, Abhinandan; Deshmukh, Mandar M.

    2016-03-01

    We present a process to fabricate electromechanical pressure sensors using multilayer graphene in a sealed drum geometry. The drum resonators are fabricated on insulating sapphire substrates with a local back gate for direct radio frequency ({\\text{}}{{rf}}) actuation and detection of the mechanical modes. Using this scheme, we show the detection and electrostatic tuning of multiple resonant modes of the membrane up to 200 MHz. The geometry of the device also helps in attaining low tensile stress in the membrane, thereby giving high gate tunability (∼1 MHz/V) of the resonator modes. We study the resonant frequency shifts in the presence of helium gas and demonstrate a sensing capability of 1 Torr pressure in a cryogenic environment.

  11. Flow of magnetized grains in a rotating drum.

    PubMed

    Lumay, G; Vandewalle, N

    2010-10-01

    We have experimentally investigated the influence of a magnetic interaction between the grains on the flow of a granular material in a rotating drum. The magnetic cohesion is induced by applying a homogeneous external magnetic field B oriented either parallel or perpendicular to the gravity g. The drum rotating speed has been selected to obtain a continuous flow when the magnetic field is switched off. We show that, for both magnetic field orientations, the cohesion is able to induce a transition between the continuous flow regime to the discrete avalanche regime. The avalanche dynamics is periodic when B⊥g and irregular when B∥g. Moreover, the maximal angle of stability θ(m) increases strongly with the cohesion strength and could be higher than 90° when B⊥g. A toy model based on the stability of a magnetic block on a magnetic inclined plane is proposed to explain this behavior. PMID:21230228

  12. Flow of magnetized grains in a rotating drum

    NASA Astrophysics Data System (ADS)

    Lumay, G.; Vandewalle, N.

    2010-10-01

    We have experimentally investigated the influence of a magnetic interaction between the grains on the flow of a granular material in a rotating drum. The magnetic cohesion is induced by applying a homogeneous external magnetic field B⃗ oriented either parallel or perpendicular to the gravity g⃗ . The drum rotating speed has been selected to obtain a continuous flow when the magnetic field is switched off. We show that, for both magnetic field orientations, the cohesion is able to induce a transition between the continuous flow regime to the discrete avalanche regime. The avalanche dynamics is periodic when B⃗⊥g⃗ and irregular when B⃗∥g⃗ . Moreover, the maximal angle of stability θm increases strongly with the cohesion strength and could be higher than 90° when B⃗⊥g⃗ . A toy model based on the stability of a magnetic block on a magnetic inclined plane is proposed to explain this behavior.

  13. Investigation of single crystal zircon, (Zr,Pu)SiO4 doped with Pu

    NASA Astrophysics Data System (ADS)

    Hanchar, J. M.; Burakov, B. E.; Anderson, E. B.; Zamoryanskaya, M. V.

    2003-04-01

    Zircon-based ceramics are under consideration as durable waste forms for immobilization of weapons grade plutonium and other actinide elements. Samples of polycrystalline zircon doped with 238Pu and 239Pu have been obtained in previous studies. These materials, however, are difficult to use for precise measurement of the leach-rate of Pu, and to accurately determine the level of Pu doping that can be attained in zircon, (Zr,Pu)SiO_4. Single crystals of 238Pu doped zircon (ranging from 0.3 to 3.5 mm in size) were successfully grown for the first time ever using a Li-Mo flux synthesis method. The incorporation of Pu ranged from 1.9 to 4.7 wt. % el. (with approximately 81 wt.% of 238Pu isotope) based on electron microprobe analysis. The zircon crystals were pinkish-brown when they were crystallized, and then over a period of five months changed to a brown color. After fourteen months the crystals turned to a brown-gray color. The zircon crystals glow in the dark probably from alpha particle induced luminescence. The intensity of the cathodoluminescence (CL) emission in the Pu doped crystals is correlated with the Pu content, and the CL emission showed no change 141 days after the initial CL measurements were made. Single crystal X-ray diffraction results obtained 141 days after synthesis indicate unit cell parameters (in angstroms): a = 6.6267(15), c = 5.9992(10) and a cell volume of 263.41(10). When the zircon crystals were grown, they were free of cracks. Over the course of five months cracks appeared throughout the crystals, and after fourteen months the cracks became much more abundant. The zircon crystals were transparent upon crystallization, and even with numerous cracks throughout the crystals remain transparent. Radiation damage calculations indicate that after only a short period of time, six months, these zircon crystals had already accumulated significant alpha-induced radiation damage (˜2.5 x1014 alpha-decay events per milligram). After five years they

  14. Spectroscopic Signature of Aging in (delta)-Pu(Ga)

    SciTech Connect

    Chung, B W; Schwartz, A J; Ebbinghaus, B B; Fluss, M J; Haslam, J J; Blobaum, K M; Tobin, J G

    2005-04-15

    Resonant Photoemission, a variant of Photoelectron Spectroscopy, has been demonstrated to have sensitivity to aging of Pu samples. The spectroscopic results are correlated with resistivity measurements and are shown to be the fingerprint of mesoscopic or nanoscale internal damage in the Pu physical structure. This means that a spectroscopic signature of internal damage due to aging in Pu has been established.

  15. Electronic structure of delta-Pu and PuCoGa[sub 3] from photoemission and the mixed level model

    SciTech Connect

    Joyce, J. J.; Wills, J. M.; Durakiewicz, T.; Butterfield, M. T.; Guziewicz, E.; Sarrao, John L.,; Arko, A. J.; Moore, D. P.; Morales, L. A.; Eriksson, O.

    2004-01-01

    The electronic structure of {delta}-phase Pu metal and the Pu-based superconductor PuCoGa{sub 5} is explored using photoelectron spectroscopy and a novel theoretical scheme. Excellent agreement between calculation and experiment defines a path forward for understanding electronic structure aspects of Pu-based materials. The photoemission results show two separate regions of 5f electron spectral intensity, one at the Fermi energy and another centered 1.2 eV below the Fermi level. A comparison is made between the photoemission data and five computational schemes for {delta}-Pu. The results for {delta}-Pu and PuCoGa{sub 5} indicate 5f electron behavior on the threshold between localized and itinerant and a broader framework for understanding the fundamental electronic properties of the Pu 5f levels in general within two configurations, one localized and one itinerant.

  16. The evolution of harmonic Indian musical drums: A mathematical perspective

    NASA Astrophysics Data System (ADS)

    Gaudet, Samuel; Gauthier, Claude; Léger, Sophie

    2006-03-01

    We explain using mathematics how harmonic musical drums were discovered by Indian artisans and musicians more than 2000 years ago. To this end, we introduce a harmonic error function which measures the quality of the harmonic relationship and degeneracy of the first modes of vibration of a centrally symmetric loaded membrane. We explain that although the tabla configuration found by the ancient Indians is the most natural one, other configurations exist and some are harmonically superior to the classical one.

  17. 26. Detail view of drum girder with rollers below, resting ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    26. Detail view of drum girder with rollers below, resting on fixed turntable upon masonry center pier. Swing drive shaft (vertical) is turned by level gear of horizontal shaft (protruding through machine room wall), which turns pinion gear toothed to fixed turntable rack below rollers. (Nov. 25, 1988) - University Heights Bridge, Spanning Harlem River at 207th Street & West Harlem Road, New York County, NY

  18. Vertical distributions of radionuclides ((239+240)Pu, (240)Pu/(239)Pu, and (137)Cs) in sediment cores of Lake Bosten in Northwestern China.

    PubMed

    Liao, Haiqing; Bu, Wenting; Zheng, Jian; Wu, Fengchang; Yamada, Masatoshi

    2014-04-01

    Artificial radionuclides ((137)Cs, (239+240)Pu, (241)Pu, (241)Am) deposited in lacustrine sediments have been used for dating as well as radionuclide source identification. In the present work, we investigated the vertical distributions of (239+240)Pu and (137)Cs activities, (240)Pu/(239)Pu atom ratios, and (239+240)Pu/(137)Cs activity ratios in sediment cores collected from Lake Bosten, which is the lake closest to the Lop Nor Chinese Nuclear Weapon Test site in northwestern China. Uniformly high concentrations of (239+240)Pu and (137)Cs were found in the upper layers deposited since 1964 in the sediment cores, and these were controlled by the resuspension of soil containing radionuclides from the nearby land surface. As the Chinese nuclear tests varied remarkably in yield, the mixing of the tropospheric deposition from these tests and the stratospheric deposition of global fallout has led to a (240)Pu/(239)Pu atom ratio that is similar to that of global fallout and to a (239+240)Pu/(137)Cs activity ratio that is slightly higher than that of global fallout. However, a low (240)Pu/(239)Pu atom ratio of 0.080 and high (239+240)Pu/(137)Cs activity ratio of 0.087, significantly different from the global fallout values, were observed in one sediment core (07BS10-2), indicating the inhomogenous tropospheric deposition from the Chinese nuclear tests in Lake Bosten during 1967-1973. These results are important to understand the influence of the CNTs on the radionuclide contamination in Lake Bosten.

  19. Determination of (239)Pu, (240)Pu, (241)Pu and (242)Pu at femtogram and attogram levels - evidence for the migration of fallout plutonium in an ombrotrophic peat bog profile.

    PubMed

    Quinto, Francesca; Hrnecek, Erich; Krachler, Michael; Shotyk, William; Steier, Peter; Winkler, Stephan R

    2013-04-01

    The isotopic composition of plutonium ((239)Pu, (240)Pu, (241)Pu and (242)Pu) was investigated in a ∼0.5 m long peat core from an ombrotrophic bog (Black Forest, Germany) using clean room procedures and accelerator mass spectrometry (AMS). This sophisticated analytical approach was ultimately needed to detect reliably the Pu concentrations present in the peat samples at femtogram (fg) and attogram (ag) levels. The mean (240)Pu/(239)Pu isotopic ratio of 0.19 ± 0.02 (N = 32) in the peat layers, representing approximately the last 80 years, was in good agreement with the accepted value of 0.18 for the global fallout in the Northern Hemisphere. This finding is largely supported by the corresponding and rather constant (241)Pu/(239)Pu (0.0012 ± 0.0005) and (242)Pu/(239)Pu (0.004 ± 0.001) ratios. Since the Pu isotopic composition characteristic of the global fallout was also identified in peat samples pre-dating the period of atmospheric atom bomb testing (AD 1956-AD 1980), migration of Pu within the peat profile is clearly indicated. These results highlight, for the first time, the mobility of Pu in a peat bog with implications for the migration of Pu in other acidic, organic rich environments such as forest soils and other wetland types. These findings constitute a direct observation of the behaviour of Pu at fg and ag levels in the environment. The AMS measurements of Pu concentrations (referring to a corresponding activity of (240+239)Pu from 0.07 mBq g(-1) to 5 mBq g(-1)) essentially confirm our a priori estimates based on existing (241)Am and (137)Cs data in the investigated peat core and agree well with the global fallout levels from the literature. Exclusively employing the Pu isotope ratios established for the peat samples, the date of the Pu irradiation (AD 1956, correctable to AD 1964) was calculated and subsequently compared to the (210)Pb age of the peat layers; this comparison provided an additional hint that global fallout derived Pu is not fixed in

  20. Prediction of thermodynamic property of Pu-zircon and Pu-pyrochlore

    NASA Astrophysics Data System (ADS)

    Xu, Hulfang; Wang, Yifeng

    2000-07-01

    Due to its high durability, zircon is often present as a heavy mineral in natural environments and is the oldest mineral that has been dated on the earth. There are four zircon structure phases of M4+SiO4 occurring in nature: zircon (ZrSiO4), hafnon (HfSiO4), thorite (ThSiO4), and coffinite (USiO4). These phases may form solid solution. Recent interest in zircon minerals stems from the study of highly durable radioactive waste forms. Crystalline phases of M4+SiO4 with zircon structure have been proposed as a durable ceramic waste form for immobilizing actinides such as Pu, Np, and U. To predict the behavior of zircon-based waste forms in a geologic repository environment as well as to optimize the fabrication of those waste forms, the thermodynamic and kinetic properties for zircon mineral phases have to be determined. In this paper, we use a linear free energy relationship to predict the Gibbs free energies of formation of Pu-bearing phases (Xu et al., 1999). The calculated results show that the PuSiO4 phase with zircon structure is unstable with respect to oxides of PuO2 and quartz. However, the PuSiO4 phase will be stable with respect to oxides of PuO2 and silica glass at low temperature.

  1. Handling 78,000 drums of mixed-waste sludge

    SciTech Connect

    Berry, J.B.; Gilliam, T.M.; Harrington, E.S.; Youngblood, E.L. ); Baer, M.B. )

    1991-01-01

    The Oak Ridge Gaseous Diffusion Plant (now know as the Oak Ridge K-25 Site) prepared two mixed-waste surface impoundments for closure by removing the sludge and contaminated pond-bottom clay and attempting to process it into durable, nonleachable, concrete monoliths. Interim, controlled, above-ground storage of the stabilized waste was planned until final disposition. The strategy for disposal included delisting the stabilized pond sludge from hazardous to nonhazardous and disposing of the delisted monoliths as radioactive waste. Because of schedule constraints and process design and control deficiencies, {approximately}46,000 drums of material in various stages of solidification and {approximately}32,000 drums of unprocessed sludge are presently being stored. In addition, the abandoned treatment facility still contains {approximately}16,000 gal of raw sludge. Such conditions do not comply with the requirements set forth by the Resource Conservation and Recovery Act (RCRA) for the storage of listed waste. Various steps are being taken to bring the storage of {approximately}78,000 drums of mixed waste into compliance with RCRA. This paper (1) reviews the current situation, (2) discusses the plan for remediation of regulatory noncompliances, including decanting liquid from stabilized waste and dewatering untreated waste, and (3) provides an assessment of alternative raw-waste treatment processes. 1 ref., 6 figs., 2 tabs.

  2. Scaling of heat transfer in granular material in rotating drums

    NASA Astrophysics Data System (ADS)

    Yohannes, Bereket; Emady, Heather; Pardes, Ingrid; Javed, Maham; Borghard, William; Glasser, Benjamin; Muzzio, Fernando; Cuitino, Alberto

    Several industrial processes involve thermal treatment of granular materials and powders, in devices such as rotating drums, to bring about a desired chemical and/or physical transformation. Developing a better understanding of the heat transfer process can significantly improve the quality of the end product and efficiency. However, there is a lack of predictive models, for example, to predict the evolution of the distribution and average of the particles' temperature, particularly for the purposes of scale-up from laboratory scale experiments to manufacturing scale productions. We used discrete element method (DEM) based simulations to study the distribution of particles' temperature in rotating drums at low temperature. Various physical, mechanical, and thermal properties of particles were considered in the simulations and in the analysis. In addition, the effect of operating conditions such as size of drum, material fill level, and speed of rotation on the heat transfer were investigated. Based on the simulations, we identified timescales relevant to the heat transfer process and developed a relationship between these timescales that can be used to predict the average temperature of particles. We also found that the evolution of the temperature distribution, since different particles may have different temperatures, can be predicted based on these timescales. These findings can be used to predict the required time to heat up all particles to the desired temperature.

  3. Axial transport of bidisperse granular mixtures in a rotating drum

    NASA Astrophysics Data System (ADS)

    Khan, Zeina

    2005-03-01

    Bidisperse granular mixtures rapidly size segregate when tumbled in a partially filled, horizontal drum. The smaller component moves radially toward the axis of rotation and forms a buried core. On a longer time scale, axial modulations of the core may develop and grow into a series of bands along the drum, which become visible upon breaking the surface. Using a narrow pulse of the smaller component as the intitial condition, we observe that the axial transport of the radial core is a subdiffusive front advancement process. The front motion is subdiffusive in the sense that the radially integrated concentration forms a self-similar, compact axial pulse whose width grows as t^α, with α˜1/3 < 1/2, and hence it spreads much more slowly than by diffusion in a mixture which does not exhibit axial banding. By coloring some of the larger grains, we find that the mixing and axial transport of the larger grains is similarly subdiffusive. We report on the effects of changing relative grain size and drum diameter on the axial transport of grains. We find that mixing occurs in the radial core, and axial band formation is enhaced in these cases.

  4. Subdiffusion of segregated granular materials in a long rotating drum

    NASA Astrophysics Data System (ADS)

    Khan, Zeina S.; Tokaruk, Wayne A.; Morris, Stephen W.

    2004-03-01

    Granular mixtures rapidly segregate radially by size when tumbled in a partially filled horizontal drum. The smaller component moves toward the axis of rotation and forms a buried core. On a longer time scale, axial modulations of the core may develop and grow into a series of bands along the drum, visible upon breaking the surface. Segregation models have generally assumed that axial diffusion of the smaller component determines the short wavelength cutoff of the band pattern. Using narrow pulses of the smaller component as initial conditions, we have characterized axial transport in the core. We find that the axial advance of the segregated core is well described by a self-similar concentration profile whose width scales as t^α, with α ˜ 0.3 < 1/2. Thus the process is subdiffusive rather than diffusive as previously assumed. We find that α is nearly independent of the grain type and drum rotation rate within the smoothly streaming regime. We compare our results to two one-dimensional PDE models which contain self-similarity and subdiffusion; a linear fractional diffusion model and the nonlinear porous medium equation.

  5. Pu speciation in actual and simulated aged wastes

    SciTech Connect

    Lezama-pacheco, Juan S; Conradson, Steven D

    2008-01-01

    X-ray Absorption Fine Structure Spectroscopy (XAFS) at the Pu L{sub II/III} edge was used to determine the speciation of this element in (1) Hanford Z-9 Pu crib samples, (2) deteriorated waste resins from a chloride process ion-exchange purification line, and (3) the sediments from two Waste Isolation Pilot Plant Liter Scale simulant brine systems. The Pu speciation in all of these samples except one is within the range previously displayed by PuO{sub 2+x-2y}(OH){sub y}{center_dot}zH{sub 2}O compounds, which is expected based on the putative thermodynamic stability of this system for Pu equilibrated with excess H{sub 2}O and O{sub 2} under environmental conditions. The primary exception was a near neutral brine experiment that displayed evidence for partial substitution of the normal O-based ligands with Cl{sup -} and a concomitant expansion of the Pu-Pu distance relative to the much more highly ordered Pu near neighbor shell in PuO{sub 2}. However, although the Pu speciation was not necessarily unusual, the Pu chemistry identified via the history of these samples did exhibit unexpected patterns, the most significant of which may be that the presence of the Pu(V)-oxo species may decrease rather than increase the overall solubility of these compounds. Several additional aspects of the Pu speciation have also not been previously observed in laboratory-based samples. The molecular environmental chemistry of Pu is therefore likely to be more complicated than would be predicted based solely on the behavior of PuO{sub 2} under laboratory conditions.

  6. Biokinetics of sup 237 Pu citrate and nitrate in the rat: Implications for Pu studies in man

    SciTech Connect

    Talbot, R.J.; Knight, D.A.; Morgan, A. )

    1990-08-01

    Plutonium-237 decays mainly by electron capture with a half-life of 45 d. Alpha particles are emitted in only 5 x 10(-3)% of its disintegrations. This nuclide can now be produced with relatively small amounts of alpha-emitting contaminants so that, in principle, {sup 237}Pu can be used for studies of Pu biokinetics in man. However, because of its high specific activity, there was some doubt that its metabolism would be the same as that of the alpha- and beta-emitting isotopes of Pu normally encountered in the nuclear industry. In this study, the biokinetics of nearly pure, high specific activity {sup 237}Pu are compared with those of lower specific activity, impure {sup 237}Pu containing significant amounts of alpha-emitting Pu, following administration to rats by intravenous injection as the citrate. Both the distribution and excretion of the pure and impure {sup 237}Pu used in the two studies were similar and also in good agreement with the results of previously reported studies using {sup 239}Pu and {sup 241}Pu citrate, thus validating the use of {sup 237}Pu for studies of Pu metabolism in man. Data on the biokinetics of {sup 237}Pu nitrate are also included.

  7. Redox reactions of Pu(IV) and Pu(III) in the presence of acetohydroxamic acid in HNO(3) solutions.

    PubMed

    Tkac, Peter; Precek, Martin; Paulenova, Alena

    2009-12-21

    The reduction of Pu(IV) in the presence of acetohydroxamic acid (HAHA) was monitored by vis-NIR spectroscopy. All experiments were performed under low HAHA/Pu(IV) ratios, where only the Pu(IV)-monoacetohydroxamate complex and Pu uncomplexed with HAHA were present in relevant concentrations. Time dependent concentrations of all absorbing species were resolved using molar extinction coefficients for Pu(IV), Pu(III), and the Pu(AHA)(3+) complex by deconvolution of spectra. From fitting of the experimental data by rate equations integrated by a numeric method three reactions were proposed to describe a mechanism responsible for the reduction and oxidation of plutonium in the presence of HAHA and HNO(3). Decomposition of Pu(AHA)(3+) follows a second order reaction mechanism with respect to its own concentration and leads to the formation of Pu(III). At low HAHA concentrations, a two-electron reduction of uncomplexed Pu(IV) with HAHA also occurs. Formed Pu(III) is unstable and slowly reoxidizes back to Pu(IV), which, at the point when all HAHA is decomposed, can be catalyzed by the presence of nitrous acid.

  8. Complementary Pu Resuspension Study at Palomares, Spain

    SciTech Connect

    Shinn, J

    2002-10-01

    Soil in an area near Palomares, Spain, was contaminated with plutonium as a result of a mid-air collision of U.S. military aircraft in January 1966. The assessment for potential inhalation dose can be found in Iranzo et al., (1987). Long-term monitoring has been used to evaluate remedial actions (Iranzo et al., 1988) and there are many supporting studies of the Pu contamination at Palomares that have been carried out by the Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT) in Madrid. The purpose of this study is to evaluate the resuspension of Pu from the soil in terms of Pu-concentrations in air and resuspension rates in a complementary investigation to those of CIEMAT but in an intensive short-term field effort. This study complements the resuspension studies of CIEMAT at Palomares with additional information, and with confirmation of their previous studies. Observed mass loadings (M) were an average of 70 mg/m{sup 3} with peaks in the daytime of 130 mg/m{sup 3} and low values at night below 30 {micro}g/m{sup 3}. The Pu-activity of aerosols (A) downwind of plot 2-1 was 0.12 Bq/g and the enhancement factor (E{sub f}) had a value of 0.3, which is low but similar to a typical value of 0.7 for other undisturbed sites. This E{sub f} value may increase further away from ground zero. The particle size distribution of the Pu in air measured by cascade impactors was approximately lognormal with a median aerodynamic diameter of 3.7 {micro}m and a geometric standard deviation of 3.5 in the respirable range. This peak midway between 1 ? m and 10 {micro}m in the respirable range is commonly observed. Daily fluctuations in the Pu concentration in air (C) detected by the UHV were lognormally distributed with a geometric standard deviation of 4.9 indicating that the 98th percentile would be 24 times as high as the median. Downwind of plot 2-1 the mean Pu concentration in air, C, was 8.5 {micro}Bq/m{sup 3}. The resuspension factor (Sf) was 2.4 x 10

  9. Contamination control aspects of attaching waste drums to the WIPP Waste Characterization Chamber

    SciTech Connect

    Rubick, L.M.; Burke, L.L.

    1998-12-31

    Argonne National Laboratory West (ANL-W) is verifying the characterization and repackaging of contact-handled transuranic (CH-TRU) mixed waste in support of the Waste Isolation Pilot Program (WIPP) project located in Carlsbad, New Mexico. The WIPP Waste Characterization Chamber (WCC) was designed to allow opening of transuranic waste drums for this process. The WCC became operational in March of 1994 and has characterized approximately 240 drums of transuranic waste. The waste drums are internally contaminated with high levels of transuranic radionuclides. Attaching and detaching drums to the glove box posed serious contamination control problems. Prior to characterizing waste, several drum attachment techniques and materials were evaluated. An inexpensive HEPA filter molded into the bagging material helps with venting during detachment. The current techniques and procedures used to attach and detach transuranic waste drums to the WCC are described.

  10. Fire testing of 55 gallon metal waste drums for dry waste storage

    SciTech Connect

    Hasegawa, H.K.; Staggs, K.J.; Doughty, S.M.

    1993-07-01

    The primary goal of this test program was to conduct a series of fire test to provide information on the fire performance of 55 gallon metal waste drums used for solid waste disposal at Department Of Energy (DOE) facilities. This program was limited in focus to three different types of 55 gallon drums, one radiant heat source, and one specific fire size. The initial test was a single empty 55 gallon drum exposed to a standard ASTME-119 time temperature curve for over 10 minutes. The full scale tests involved metal drums exposed to a 6{prime} diameter flammable liquid fire for a prescribed period of time. The drums contained simulated dry waste materials of primarily class A combustibles. The test results showed that a conventional 55 gallon drum with a 1in. bung would blow its lid consistently.

  11. Self-irradiation of Pu, its alloys and compounds

    NASA Astrophysics Data System (ADS)

    Timofeeva, L. F.

    2000-07-01

    Self-irradiation of Pu, its alloys and compounds by products of known α-decomposition is a continuous complicated process, which includes numerous different phenomena. The accumulation of Pu decomposition products causes material structure and properties change. This problem is the subject of many works, most of them concerned with the behavior of Pu and its alloys at low (liquid He and N) temperatures. The survey is given of the results of our experiments connected with radiogenic helium behavior, crystal structure and properties of Pu metallic compounds and Pu oxide ceramics in a self-irradiation process at room temperature under isochronal heat treatments.

  12. Waste drum gas generation sampling program at Rocky Flats during FY 1989

    SciTech Connect

    Roggenthen, D.K.; Nieweg, R.G.

    1990-10-01

    Rocky Flats Plant transuranic waste drums were sampled for gas composition. Glass, metal, graphite, and solidified inorganic sludge transuranic waste forms were sampled. A vacuum system was used to sample each layer of containment inside a waste drum, including individual waste bags. G values were calculated for the waste drums. G(H{sub 2}) was below 0.6 and G(Total) was below 1.3 for all waste forms discussed in this report. 5 refs., 3 figs., 3 tabs.

  13. Characterization of void volume VOC concentration in vented TRU waste drums. Final report

    SciTech Connect

    Liekhus, K.J.

    1995-08-01

    A test program has been conducted at the Idaho National Engineering Laboratory to demonstrate that the concentration of volatile organic compounds within the innermost layer of confinement in a vented waste drum can be estimated using a model incorporating diffusion and permeation transport principles and limited waste drum sampling data. This final report summarizes the experimental measurements and model predictions for transuranic waste drums containing solidified sludges and solid waste.

  14. Characterization of voic volume VOC concentration in vented TRU waste drums. Final report

    SciTech Connect

    Liekhus, K.J.

    1994-12-01

    A test program has been conducted at the Idaho National Engineering Laboratory to demonstrate that the concentration of volatile organic compounds within the innermost layer of confinement in a vented waste drum can be estimated using a model incorporating diffusion and permeation transport principles and limited waste drum sampling data. This final report summarizes the experimental measurements and model predictions for transuranic waste drums containing solidified sludges and solid waste.

  15. Incidence of the leech Actinobdella pediculata on freshwater drum in Lake Erie

    USGS Publications Warehouse

    Bur, Michael T.

    1994-01-01

    Actinobdella pediculata (Glossiphoniidae), a freshwater leech, was found attached to freshwater drum (Aplodinotus grunniens) from western Lake Erie during 1991 through 1993. The animal was first observed during routine examinations of freshwater drum collected in May 1991. The leeches were usually attached to the inside, lower portion of the opercula near the isthmus. Incidence of attachment increased with freshwater drum age and length. No noticeable adverse effects on the fish from attachment by the leech were noted.

  16. Pharyngeal teeth of the freshwater drum (Aplodinotus grunniens) a predator of the zebra mussel (Dreissena polymorpha)

    USGS Publications Warehouse

    French, John R. P.

    1997-01-01

    The morphology of pharyngeal teeth of freshwater drum (Aplodinotus grunniens) was studied to determine changes that occur during growth of drum that may relate to consumption of zebra mussel (Dreissena polymorpha) by larger fish. Pharyngeal teeth were of three types. Cardiform teeth were replaced by villiform teeth, which were replaced by molariform teeth as the size class of drum increased. Molariform teeth comprised over 85% of total surface area of dentition in fish 265 mm long.

  17. Comparative study of the fragments' mass and energy characteristics in the spontaneous fussion of 238Pu, 240Pu and 242Pu and in the thermal-neutron-induced fission of 239Pu

    NASA Astrophysics Data System (ADS)

    Schillebeeckx, P.; Wagemans, C.; Deruytter, A. J.; Barthélémy, R.

    1992-08-01

    The energy and mass distribution and their correlations have been studied for the spontaneous fission of 238, 240, 242Pu and for the thermal-neutron-induced fission of 239Pu. A comparison of 240Pu(s.f.) and 239Pu(nth,f) shows that the increase in excitation energy mainly results in an increase of the intrinsic excitation energy. A comparison of the results for 238Pu, 240Pu and 242Pu(s.f.) demonstrates the occurence of different fission modes with varying relative probability. These results are discussed in terms of the scission point model as well as in terms of the fission channel model with random neck-rupture.

  18. PuPO4(cr, hyd.) Solubility Product and Pu3+ Complexes With Phosphate and Ethylenediaminetetraacetic Acid

    SciTech Connect

    Rai, Dhanpat; Moore, Dean A.; Felmy, Andrew R.; Rosso, Kevin M.; Bolton, Harvey

    2010-06-15

    To determine the solubility product of PuPO4(cr, hyd.) and the complexation constants of Pu(III) with phosphate and EDTA, the solubility of PuPO4(cr, hyd.) was investigated as a function of: 1) time and pH varying from 1.0 to 12.0 and at a fixed 0.00032 M phosphate concentration; 2) NaH2PO4 concentrations varying from 0.0001 M to 1.0 M and at a fixed pH value of 2.5; 3) time and pH varying from 1.3 to 13.0 at fixed concentrations of 0.00032 M phosphate and 0.0004 M or 0.002 M Na2H2EDTA; and 4) Na2H2EDTA concentrations varying from 0.00005 M to 0.0256 M at a fixed 0.00032 M phosphate concentration and at pH values of approximately 3.5, 10.6, and 12.6. A combination of solvent extraction and spectrophotometric techniques confirmed that the use of hydroquinone and Na2S2O4 helped maintain Pu as Pu(III). The solubility data were interpreted using Pitzer and SIT models, and both provided similar values for the solubility product of PuPO4(cr, hyd.) and for the formation constant of PuEDTA-. The log10 of the solubility product of PuPO4(cr, hyd.) (PuPO4(cr, hyd.) = Pu3+ + PO4 ) was determined to be –(24.42 ± 0.38). Pitzer modeling showed that phosphate interactions with Pu3+ were extremely weak and did not require any phosphate complexes (e.g., PuPO4(aq), PuH2PO42+, Pu(H2PO4)2+, Pu(H2PO4)3(aq), and Pu(H2PO4)4-), as proposed in existing literature, to explain the experimental data. SIT modeling, however, required the inclusion of PuH2PO42+ to explain the data in high NaH2PO4 concentrations; this illustrates the differences one can expect when using these two chemical models to interpret the data. As the Pu(III)-EDTA species, only PuEDTA- was needed to interpret the experimental data in a large range in pH values (1.3–12.9) and EDTA concentrations (0.00005–0.256 M). Calculations based on density functional theory support the existence of PuEDTA- (with prospective stoichiometry as Pu(OH2)3EDTA-) as the chemically and structurally stable species. The log10 of the

  19. Analysis of upper arm muscle activation using surface electromyography signals during drum playing

    PubMed Central

    Chong, Hyun Ju; Kwon, Chun-Ki; Kang, Hyun-Joo; Kim, Soo Ji

    2016-01-01

    This study measured surface electromyography of the biceps brachii and triceps brachii during repeated drum playing with and without a drumstick to better understand activation of the upper arm muscles and inform the use of instrument playing for motor rehabilitation. A total of 40 healthy college students participated in this study. All participants were asked to strike a drum with their hand and with a drumstick at three different levels of stroke: soft, medium, and strong. The stroke order was randomly assigned to participants. A sound level meter was used to record the intensity of the drum playing. Surface electromyography signals were recorded at every hit during drum playing both with and without the drumstick in each of the three stroke conditions. The results demonstrated that the highest muscle activation was observed in both biceps brachii and triceps brachii with strong drum playing with and without the drumstick. A two-way repeated measures analysis of variance showed that there was a significant main effect for stroke intensity in muscle activation and produced sound level. While higher activation of the triceps brachii was observed for drum playing without a drumstick, no significant differences were found between the biceps brachii and sound level. This study demonstrated via surface electromyography data that greater muscle activation of the biceps brachii and triceps brachii does not occur with the use of drumsticks in drum playing. With the drum sound controlled, drum playing by hand can be an effective therapeutic intervention for the upper arm muscles. PMID:27419114

  20. Analysis of upper arm muscle activation using surface electromyography signals during drum playing.

    PubMed

    Chong, Hyun Ju; Kwon, Chun-Ki; Kang, Hyun-Joo; Kim, Soo Ji

    2016-06-01

    This study measured surface electromyography of the biceps brachii and triceps brachii during repeated drum playing with and without a drumstick to better understand activation of the upper arm muscles and inform the use of instrument playing for motor rehabilitation. A total of 40 healthy college students participated in this study. All participants were asked to strike a drum with their hand and with a drumstick at three different levels of stroke: soft, medium, and strong. The stroke order was randomly assigned to participants. A sound level meter was used to record the intensity of the drum playing. Surface electromyography signals were recorded at every hit during drum playing both with and without the drumstick in each of the three stroke conditions. The results demonstrated that the highest muscle activation was observed in both biceps brachii and triceps brachii with strong drum playing with and without the drumstick. A two-way repeated measures analysis of variance showed that there was a significant main effect for stroke intensity in muscle activation and produced sound level. While higher activation of the triceps brachii was observed for drum playing without a drumstick, no significant differences were found between the biceps brachii and sound level. This study demonstrated via surface electromyography data that greater muscle activation of the biceps brachii and triceps brachii does not occur with the use of drumsticks in drum playing. With the drum sound controlled, drum playing by hand can be an effective therapeutic intervention for the upper arm muscles. PMID:27419114

  1. EVALUATION OF RADIOLYSIS INDUCED HYDROGEN GENERATION IN DOT 6M DRUMS FROM INTEC

    SciTech Connect

    Vinson, D

    2007-06-18

    Three DOT 6M 30-gallon drums are scheduled to be shipped from the Idaho Nuclear Technology Engineering Center (INTEC) at the Idaho National Laboratory (INL) to L-Area at the Savannah River Site (SRS). These three drums contain radioactive materials that resulted from the material recovery effort following a small explosion that had occurred in the Idaho Chemical Processing Plant (ICPP) hot chemistry laboratory (HCL). In support of the shipment and subsequent storage of the three DOT 6M drums, an evaluation of the potential for molecular hydrogen production in the drums has been completed and documented herein. The potential sources of hydrogen evaluated in the current report include radiolytic decomposition of polymeric materials in the DOT 6M drums No.3031 and No.3598 and the radiolytic decomposition of water in drum No.20102. No other potential sources have been identified based upon reported drum contents and packaging configuration. A parametric approach was used to evaluate the maximum quantity of molecular hydrogen that can be expected to evolve in two DOT 6M 30-gallon drums in support of receipt and subsequent interim storage prior to canyon processing. These drums are two of three drums scheduled for shipment from INTEC to SRS as part of the decommissioning effort of the INTEC facility. The three DOT 6M drums will be received at L-Area in SRS and stored for up to 13-years prior to final disposition at HB-Line in 2020. Results of the current analysis do not include parametric analysis of drum No.20102 containing 114/133 SAL (salvage) which contains UO{sub 3} powder. This drum has not been identified as containing polymeric materials and a conservative calculation indicates that the maximum gross molecular hydrogen production due to the radiolysis of adsorbed moisture would yield a production rate of 5.1-cm{sup 3}/yr, driven primarily by the large surface are to volume ratio of the oxide powder. The remaining two drums, No.3031 and No.3598 contain polymer

  2. Modeling unsteady-state VOC transport in simulated waste drums. Revision 1

    SciTech Connect

    Liekhus, K.J.; Gresham, G.L.; Peterson, E.S.; Rae, C.; Hotz, N.J.; Connolly, M.J.

    1994-01-01

    This report is a revision of an EG&G Idaho informal report originally titled Modeling VOC Transport in Simulated Waste Drums. A volatile organic compound (VOC) transport model has been developed to describe unsteady-state VOC permeation and diffusion within a waste drum. Model equations account for three primary mechanisms for VOC transport from a void volume within the drum. These mechanisms are VOC permeation across a polymer boundary, VOC diffusion across an opening in a volume boundary, and VOC solubilization in a polymer boundary. A series of lab-scale experiments was performed in which the VOC concentration was measured in simulated waste drums under different conditions. A lab-scale simulated waste drum consisted of a sized-down 55-gal metal drum containing a modified rigid polyethylene drum liner. Four polyethylene bags were sealed inside a large polyethylene bag, supported by a wire cage, and placed inside the drum liner. The small bags were filled with VOC-air gas mixture and the VOC concentration was measured throughout the drum over a period of time. Test variables included the type of VOC-air gas mixtures introduced into the small bags, the small bag closure type, and the presence or absence of a variable external heat source. Model results were calculated for those trials where the permeability had been measured.

  3. RESULTS OF ANALYSIS OF NGS CONCENTRATE DRUM SAMPLES [Next Generation Solvent

    SciTech Connect

    Peters, T.; Williams, M.

    2013-09-13

    Savannah River National Laboratory (SRNL) prepared two drums (50 gallons each in Drum#2 and Drum#4) of NGS-MCU (Next Generation Solvent-Modular CSSX Unit) concentrate for future use at MCU in downblending the BOBCalixC6 based solvent to produce NGS-MCU solvent. Samples of each drum were sent for analysis. The results of all the analyses indicate that the blend concentrate is of the correct composition and should produce a blended solvent at MCU of the desired formulation.

  4. Remote-Handled Transuranic Waste Drum Venting - Operational Experience and Lessons Learned

    SciTech Connect

    Clements, Th.L.Jr.; Bhatt, R.N.; Troescher, P.D.; Lattin, W.J.

    2008-07-01

    Remote-handled transuranic (RH TRU) waste drums must be vented to meet transportation and disposal requirement before shipment to the Waste Isolation Pilot Plant. The capability to perform remote venting of drums was developed and implemented at the Idaho National Laboratory. Over 490 drums containing RH TRU waste were successfully vented. Later efforts developed and implemented a long-stem filter to breach inner waste bags, which reduced layers of confinement and mitigated restrictive transportation wattage limits. This paper will provide insight to the technical specifications for the drum venting system, development, and testing activities, startup, operations, and lessons learned. (authors)

  5. Magnetic properties of unrusted steel drums from laboratory and field-magnetic measurements

    SciTech Connect

    Ravat, D.

    1996-09-01

    Detection and precise location of buried ferromagnetic objects and estimation of the type and quantity of the objects are becoming increasingly important in environmental investigations worldwide. If laboratory-derived magnetizations were used to model steel drums, the models would under-estimate the resulting magnetic anomalies considerably and, in turn, would overestimate the number of buried drums at an environmental investigation site. Apparent bulk magnetization values for unrusted vertically oriented 55 and 30 gallon drums have been calculated (i.e., the values corrected for the effect of shape demagnetization of the drums). These range from {approximately}90 to {approximately}125 SI units for volume susceptibility and from {approximately} 325 to {approximately} 2,750 A/m for remanent magnetization (based on eight 55 gallon and four 30 gallon drums). Further deviations in these values could arise from the and thickness of the steel and variations in manufacturing conditions affecting magnetizations. From the point of view of modeling the drums, at most source-to-observation distances applicable to environmental investigations, the equivalent source method is able to approximate the observed anomalies of steel drums better than the 3-D modeling method. With two years of rusting, magnetic anomalies of some of the drums have reduced, while in other drums they have slightly increased. The overall magnetic changes caused by rusting appear to be more complex than anticipated, at least in the initial phase of rusting.

  6. Analysis of upper arm muscle activation using surface electromyography signals during drum playing.

    PubMed

    Chong, Hyun Ju; Kwon, Chun-Ki; Kang, Hyun-Joo; Kim, Soo Ji

    2016-06-01

    This study measured surface electromyography of the biceps brachii and triceps brachii during repeated drum playing with and without a drumstick to better understand activation of the upper arm muscles and inform the use of instrument playing for motor rehabilitation. A total of 40 healthy college students participated in this study. All participants were asked to strike a drum with their hand and with a drumstick at three different levels of stroke: soft, medium, and strong. The stroke order was randomly assigned to participants. A sound level meter was used to record the intensity of the drum playing. Surface electromyography signals were recorded at every hit during drum playing both with and without the drumstick in each of the three stroke conditions. The results demonstrated that the highest muscle activation was observed in both biceps brachii and triceps brachii with strong drum playing with and without the drumstick. A two-way repeated measures analysis of variance showed that there was a significant main effect for stroke intensity in muscle activation and produced sound level. While higher activation of the triceps brachii was observed for drum playing without a drumstick, no significant differences were found between the biceps brachii and sound level. This study demonstrated via surface electromyography data that greater muscle activation of the biceps brachii and triceps brachii does not occur with the use of drumsticks in drum playing. With the drum sound controlled, drum playing by hand can be an effective therapeutic intervention for the upper arm muscles.

  7. The geochemical coherence of Pu and Nd and the Pu-244/U-238 ratio of the early solar system

    NASA Technical Reports Server (NTRS)

    Jones, J. H.

    1982-01-01

    Two very different sets of Pu-244/U-238 ratios have been reported for early solar system materials, one high and the other low, and this paper examines how one of these groups may yield an incorrect ratio. Recently measured partition coefficients for Pu and Sm (Jones, 1981) are used to evaluate Pu-Nd fractionation during achondrite genesis, and Pu-244/U-238 ratios of chondrites, achondrites, and Ca-Al-rich inclusions are compared and discussed. A low Pu-244/U-238 ratio is favored, and some implications of this low ratio for galactic nucleosynthesis and meteorite age dating are briefly discussed.

  8. ²³⁹Pu and ²⁴⁰Pu inventories and ²⁴⁰Pu/²³⁹Pu atom ratios in the equatorial Pacific Ocean water column.

    PubMed

    Yamada, Masatoshi; Zheng, Jian

    2012-07-15

    The (239+240)Pu concentrations and (240)Pu/(239)Pu atom ratios were determined by alpha spectrometry and inductively coupled plasma mass spectrometry for seawater samples from two stations, one at the equator and the other in the equatorial South Pacific. To better understand the fate of Pu isotopes, this study dealt with the contribution of the close-in fallout Pu from the Pacific Proving Grounds (PPG) in water columns of the Pacific Ocean. The (239)Pu, (240)Pu and (239+240)Pu inventories over the depth interval 0-3000 m at the equator station were 10.4, 8.9 and 19.3 Bq m(-2), respectively. Further, no noticeable difference was observed in (239)Pu, (240)Pu and (239+240)Pu inventories over the depth interval 0-3000 m between the two stations. The total (239+240)Pu inventories were significantly higher than the expected cumulative deposition density of global fallout. Water column (239+240)Pu inventories measured in this study were lower than those reported for comparable stations in the Geochemical Ocean Sections Study, indicating that these inventories have been decreasing at average rates of 0.89 ± 0.07 and 0.16 ± 0.07 Bq m(-2)yr(-1) at the equator and equatorial South Pacific stations, respectively, from 1973 to 1990. The obtained (240)Pu/(239)Pu atom ratios were higher than the mean global fallout ratio of 0.18. These high atom ratios proved the existence of close-in tropospheric fallout Pu from the PPG in the Marshall Islands. The (239+240)Pu inventories originating from the close-in fallout in the entire water column were estimated to be 11.1 Bq m(-2) at the equator station and 7.1 Bq m(-2) at the equatorial South Pacific Ocean station, and the relative percentages of close-in fallout Pu were 40% at the former and 34% at the latter. A significant amount of close-in fallout Pu originating from the PPG has been transported to deep layers below the 1000 m depth in the equatorial Pacific Ocean.

  9. Fabrication of a 238Pu target

    SciTech Connect

    Wu, C Y; Chyzh, A; Kwan, E; Henderson, R; Gostic, J; Carter, D

    2010-11-16

    Precision neutron-induced reaction data are important for modeling the network of isotope production and destruction within a given diagnostic chain. This network modeling has many applications such as the design of advanced fuel cycle for reactors and the interpretation of radiochemical data related to the stockpile stewardship and nuclear forensics projects. Our current funded effort is to improve the neutron-induced reaction data on the short-lived actinides and the specific goal is to improve the neutron capture data on {sup 238}Pu with a half-life of 87.7 years. In this report, the fabrication of a {sup 238}Pu target for the proposed measurement using the DANCE array at LANL is described. The {sup 238}Pu target was fabricated from a sample enriched to 99.35%, acquired from ORNL. A total of 395 {micro}g was electroplated onto both sides of a 3 {micro}m thick Ti foil using a custom-made plating cell, shown in Fig 1. The target-material loaded Ti foil is sandwiched between two double-side aluminized mylar foils with a thickness of 1.4 {micro}m. The mylar foil is glued to a polyimide ring. This arrangement is shown partially in Fig. 2. The assembled target is then inserted into an aluminum container with a wall thickness of 0.76 mm, shown in Fig. 3. A derlin ring is used to keep the target assembly in place. The ends of this cylindrical container are vacuum-sealed by two covers with thin Kapton foils as windows for the beam entrance and exit. Shown in Fig. 4 is details of the arrangement. This target is used for phase I of the proposed measurement on {sup 238}Pu scheduled for Nov 2010 together with the DANCE array to address the safety issues raised by LANL. Shown in Fig. 5 is the preliminary results on the yield spectrum as a function of neutron incident energy with a gate on the total {gamma}-ray energy of equivalent Q value. Since no fission PPAC is employed, the distinction between the capture and fission events cannot be made, which is important for the

  10. Nevada test site fallout atom ratios: /sup 240/Pu//sup 239/Pu and /sup 241/Pu//sup 239/Pu

    SciTech Connect

    Hicks, H.G.; Barr, D.W.

    1984-02-01

    The exposure of the population in Utah to external gamma radiation from the fallout from nuclear weapons tests carried out between 1951 and 1958 at the Nevada Test Site (NTS) has been reconstructed from recent measurements of /sup 137/Cs and plutonium in soil. The fraction of /sup 137/Cs in the fallout from NTS events was calculated from the total plutonium and the /sup 240/Pu//sup 239/Pu ratios measured in the soil, using the values of 0.180 +- 0.006 and 0.032 +- 0.003 for that ratio in global fallout and NTS fallout, respectively. The total population exposure from NTS events was then calculated on the basis of exposure rates resulting from short-lived radionuclides associated with the /sup 137/Cs at the time of deposition. While the /sup 240/Pu//sup 239/Pu ratio is constant in global fallout, this ratio varies greatly in the fallout from individual events. While the composition of fallout on Utah from NTS events is rather uniform, the Off-Site Radiation Exposure Review Project is currently reconstructing radiation exposures for locations close to NTS where the fallout may be predominantly from one event. Therefore, the authors compiled the pertinent ratios in order to provide information concerning the exposure resulting from any individual event. The plutonium ratios measured at 30 days postshot were compiled from unpublished values in the archives of the Nuclear Chemistry Division of LLNL and INC-11 of LANL. These ratios are pertinent to fallout data. Dates for each event were taken from a publication by the Nevada Operations Office of the Department of Energy. 3 references.

  11. 240Pu/239Pu isotopic ratios and 239 + 240Pu total measurements in surface and deep waters around Mururoa and Fangataufa atolls compared with Rangiroa atoll (French Polynesia).

    PubMed

    Chiappini, R; Pointurier, F; Millies-Lacroix, J C; Lepetit, G; Hemet, P

    1999-09-30

    The average values of 240Pu/239Pu mass isotopic ratios of plutonium deposited in Mururoa and Fangataufa atoll sediments by French atmospheric nuclear tests range from 3.5 to 5%. In order to assess the near field and far field influence of those deposits in the open ocean, two water profiles were measured for 239 + 240Pu and 240Pu/239Pu using, for the first time, an Inductively Coupled Plasma Mass Spectrometer which was developed to achieve femtogram detection limits. One site was located at the limit of the French territorial waters, which is 22 km distant from Mururoa. The second site was located close to Rangiroa atoll, at a distance of approximately 1200-km from French nuclear test sites. The sample volumes were approximately 500 litres and plutonium was purified prior to mass spectrometry and alpha spectrometry measurements. In Rangiroa, the 239 + 240Pu profile is comparable with those already determined in world open oceans but the maximum detected activity, 9 mBq/m3 at 500-600 m is a lot lower than those measured in the northern hemisphere. 240Pu/239Pu ratios were measured between 500 and 1000 m and were not statistically different from the typical 0.18 +/- 0.01 ratio which characterises the global fallout. Consequently, any influence of plutonium from the tests in Mururoa and Fangataufa is not apparent at Rangiroa. The vertical distribution of 239 + 240Pu near Mururoa shows similar changes with depth but with a slight increase in concentration. 240Pu/239Pu mass ratios vary with depth, from 7 to 10% in the upper 500 m and in the deep waters (below 1000 m) to 15-16% between 600 and 1000 m. A contribution from plutonium deposited in the sediments at Mururoa and Fangataufa is observed at the limit of territorial waters, especially in surface and deep waters.

  12. Electronic Structure Calculations of delta-Pu Based Alloys

    SciTech Connect

    Landa, A; Soderlind, P; Ruban, A

    2003-11-13

    First-principles methods are employed to study the ground-state properties of {delta}-Pu-based alloys. The calculations show that an alloy component larger than {delta}-Pu has a stabilizing effect. Detailed calculations have been performed for the {delta}-Pu{sub 1-c}Am{sub c} system. Calculated density of Pu-Am alloys agrees well with the experimental data. The paramagnetic {yields} antiferromagnetic transition temperature (T{sub c}) of {delta}-Pu{sub 1-c}Am{sub c} alloys is calculated by a Monte-Carlo technique. By introducing Am into the system, one could lower T{sub c} from 548 K (pure Pu) to 372 K (Pu{sub 70}Am{sub 30}). We also found that, contrary to pure Pu where this transition destabilizes {delta}-phase, Pu{sub 3}Am compound remains stable in the antiferromagnetic phase that correlates with the recent discovery of a Curie-Weiss behavior of {delta}-Pu{sub 1-c}Am{sub c} at c {approx} 24 at. %.

  13. X-ray excited Auger transitions of Pu compounds

    SciTech Connect

    Nelson, Art J. Grant, William K.; Stanford, Jeff A.; Siekhaus, Wigbert J.; Allen, Patrick G.; McLean, William

    2015-05-15

    X-ray excited Pu core–valence–valence and core–core–valence Auger line-shapes were used in combination with the Pu 4f photoelectron peaks to characterize differences in the oxidation state and local electronic structure for Pu compounds. The evolution of the Pu 4f core-level chemical shift as a function of sputtering depth profiling and hydrogen exposure at ambient temperature was quantified. The combination of the core–valence–valence Auger peak energies with the associated chemical shift of the Pu 4f photoelectron line defines the Auger parameter and results in a reliable method for definitively determining oxidation states independent of binding energy calibration. Results show that PuO{sub 2}, Pu{sub 2}O{sub 3}, PuH{sub 2.7}, and Pu have definitive Auger line-shapes. These data were used to produce a chemical state (Wagner) plot for select plutonium oxides. This Wagner plot allowed us to distinguish between the trivalent hydride and the trivalent oxide, which cannot be differentiated by the Pu 4f binding energy alone.

  14. Fort Drum integrated resource assessment. Volume 2, Baseline detail

    SciTech Connect

    Dixon, D.R.; Armstrong, P.R.; Brodrick, J.R.; Daellenbach, K.K.; Di Massa, F.V.; Keller, J.M.; Richman, E.E.; Sullivan, G.P.; Wahlstrom, R.R.

    1992-12-01

    The US Army Forces Command (FORSCOM) has tasked the Pacific Northwest Laboratory (PNL) as the lead laboratory supporting the US Department of Energy (DOE) Federal Energy Management Program`s mission to identify, evaluate, and assist in acquiring all cost-effective energy projects at Fort Drum. This is a model program PNL is designing for federal customers served by the Niagara Mohawk Power Company. It will identify and evaluate all electric and fossil fuel cost-effective energy projects; develop a schedule at each installation for project acquisition considering project type, size, timing, and capital requirements, as well as energy and dollar savings; and secure 100% of the financing required to implement electric energy efficiency projects from Niagara Mohawk and have Niagara Mohawk procure the necessary contractors to perform detailed audits and install the technologies. This report documents the assessment of baseline energy use at one of Niagara Mohawk`s primary federal facilities, the FORSCOM Fort Drum facility located near Watertown, New York. It is a companion report to Volume 1, the Executive Summary, and Volume 3, the Resource Assessment. This analysis examines the characteristics of electric, gas, oil, propane, coal, and purchased thermal capacity use for fiscal year (FY) 1990. It records energy-use intensities for the facilities at Fort Drum by building type and energy end use. It also breaks down building energy consumption by fuel type, energy end use, and building type. A complete energy consumption reconciliation is presented that includes the accounting of all energy use among buildings, utilities, central systems, and applicable losses.

  15. Low-Level Waste Drum Assay Intercomparison Study

    SciTech Connect

    Greutzmacher, K.; Kuzminski, J.; Myers, S. C.

    2003-02-26

    Nuclear waste assay is an integral element of programs such as safeguards, waste management, and waste disposal. The majority of nuclear waste is packaged in drums and analyzed by various nondestructive assay (NDA) techniques to identify and quantify the radioactive content. Due to various regulations and the public interest in nuclear issues, the analytical results are required to be of high quality and supported by a rigorous Quality Assurance (QA) program. A valuable QA tool is an intercomparison program in which a known sample is analyzed by a number of different facilities. While transuranic waste (TRU) certified NDA teams are evaluated through the Performance Demonstration Program (PDP), low-level waste (LLW) assay specialists have not been afforded a similar opportunity. NDA specialists from throughout the DOE complex were invited to participate in this voluntary drum assay intercomparison study that was organized and facilitated by the Solid Waste Operations and the Safeguards Science and Technology groups at the Los Alamos National Laboratory and by Eberline Services. Each participating NDA team performed six replicate blind measurements of two 55-gallon drums with relatively low-density matrices (a 19.1 kg shredded paper matrix and a 54.4 kg mixed metal, rubber, paper and plastic matrix). This paper presents the results from this study, with an emphasis on discussing the lessons learned as well as desirable follow up programs for the future. The results will discuss the accuracy and precision of the replicate measurements for each NDA team as well as any issues that arose during the effort.

  16. Color image digitization and analysis for drum inspection

    SciTech Connect

    Muller, R.C.; Armstrong, G.A.; Burks, B.L.; Kress, R.L.; Heckendorn, F.M.; Ward, C.R.

    1993-05-01

    A rust inspection system that uses color analysis to find rust spots on drums has been developed. The system is composed of high-resolution color video equipment that permits the inspection of rust spots on the order of 0.25 cm (0.1-in.) in diameter. Because of the modular nature of the system design, the use of open systems software (X11, etc.), the inspection system can be easily integrated into other environmental restoration and waste management programs. The inspection system represents an excellent platform for the integration of other color inspection and color image processing algorithms.

  17. Habitat Suitability Index Models: Larval and juvenile red drum

    USGS Publications Warehouse

    Buckley, Jack

    1984-01-01

    A review and synthesis of existing information were used to develop a habitat model for larval and juvenile red drum. The model is scaled to produce an index of habitat suitability between 0 (unsuitable habitat) and 1 (optimally suitable habitat) for estuarine areas along the Gulf of Mexico and Atlantic coasts. Habitat suitability indices are designed for use with habitat evaluation procedures developed by the U.S. Fish and Wildlife Service. Guidelines for model application and techniques for estimating model variables are provided.

  18. An autonomous mobil robot to perform waste drum inspections

    SciTech Connect

    Peterson, K.D.; Ward, C.R.

    1994-03-01

    A mobile robot is being developed by the Savannah River Technology Center (SRTC) Robotics Group of Westinghouse Savannah River company (WSRC) to perform mandated inspections of waste drums stored in warehouse facilities. The system will reduce personnel exposure and create accurate, high quality documentation to ensure regulatory compliance. Development work is being coordinated among several DOE, academic and commercial entities in accordance with DOE`s technology transfer initiative. The prototype system was demonstrated in November of 1993. A system is now being developed for field trails at the Fernald site.

  19. Habitat Suitability Index Models: Larval and Juvenile Red Drum

    USGS Publications Warehouse

    Buckley, Jack

    1984-01-01

    A review and synthesis of existing information were used to develop a habitat model for larval and juvenile red drum. The model is scaled to produce an index of habitat suitability between 0 (unsuitable habitat) and 1 (optimally suitable habitat) for estuarine areas along the Gulf of Mexico and Atlantic coasts. Habitat suitability indices are designed for use with habitat evaluation procedures developed by the U.S. Fish and Wildlife Service. Guidelines for model application and techniques for estimating model variables are provided.

  20. Sintering of compacts of UN, (U,Pu)N, and PuN

    DOEpatents

    Tennery, V.J.; Godfrey, T.G.; Bomar, E.S.

    1973-10-16

    >A method is provided for preparing a densified compact of a metal nitride selected from the group consisting of UN, (U,Pu)N, and PuN which comprises heating a green compact of at least one selected nitride in the mononitride single-phase region, as displayed by a phase diagram of the mononitride of said compact, in a nitrogen atmosphere at a pressure of nitrogen less than 760 torr. At a given temperature, this process produces a singlephase structure and a maximal sintered density as measured by mercury displacement. (Official Gazette)

  1. Materials compatibility for 238Pu-HNO3/HF solution containment: 238Pu aqueous processing

    NASA Astrophysics Data System (ADS)

    Reimus, M. A.; Pansoy-Hjelvik, M. E.; Silver, G.; Brock, J.; Nixon, J.; Ramsey, K. B.; Moniz, P.

    2000-07-01

    The Power Source Technologies Group at Los Alamos National Laboratory is building a 238Pu Aqueous Scrap Recovery Line at the Plutonium Facility. The process line incorporates several unit operations including dissolution, filtration, ion exchange, and precipitation. During 1997-1999, studies were carried out to determine the chemistry used in the full-scale process. Other studies focussed on the engineering design of the operation. Part of the engineering design was to determine, in compatibility studies, the materials for reaction and storage vessels which will contain corrosive 238Pu-HNO3/HF solutions. The full-scale line is to be operational by the end of year 2000.

  2. Calibration Tools for Measurement of Highly Enriched Uranium in Oxide and Mixed Uranium-Plutonium Oxide with a Passive-Active Neutron Drum Shuffler

    SciTech Connect

    Mount, M; O'Connell, W; Cochran, C; Rinard, P

    2003-06-13

    Lawrence Livermore National Laboratory (LLNL) has completed an extensive effort to calibrate the LLNL passive-active neutron drum (PAN) shuffler (Canberra Model JCC-92) for accountability measurement of highly enriched uranium (HEU) oxide and HEU in mixed uranium-plutonium (U-Pu) oxide. Earlier papers described the PAN shuffler calibration over a range of item properties by standards measurements and an extensive series of detailed simulation calculations. With a single normalization factor, the simulations agree with the HEU oxide standards measurements to within {+-}1.2% at one standard deviation. Measurement errors on mixed U-Pu oxide samples are in the {+-}2% to {+-}10% range, or {+-}20 g for the smaller items. The purpose of this paper is to facilitate transfer of the LLNL procedure and calibration algorithms to external users who possess an identical, or equivalent, PAN shuffler. Steps include (1) measurement of HEU standards or working reference materials (WRMs); (2) MCNP simulation calculations for the standards or WRMs and a range of possible masses in the same containers; (3) a normalization of the calibration algorithms using the standard or WRM measurements to account for differences in the {sup 252}Cf source strength, the delayed-neutron nuclear data, effects of the irradiation protocol, and detector efficiency; and (4) a verification of the simulation series trends against like LLNL results. Tools include EXCEL/Visual Basic programs which pre- and post-process the simulations, control the normalization, and embody the calibration algorithms.

  3. Adsorption behaviour of PuF6 on UO2F2 by the use of 236Pu

    NASA Astrophysics Data System (ADS)

    Sato, Nobuaki; Matsuda, Minoru; Mitsugashira, Toshiaki; Kirishima, Akira

    2010-03-01

    To know the behavior of plutonium in the fluoride volatility process (FLUOREX PROCESS) for the spent nuclear fuel, both UO2 and PuO2 are fluorinated by fluorine forming volatile UF6 and PuF6, respectively. Then PuF6 is separated and recovered from UF6 by using adsorption materials such as uranyl fluoride UO2F2. In this paper, adsorption behavior of PuF6on UO2F2 was examined by the use of 236Pu tracer. First, the stability of UO2F2 in F2atmosphere was analyzed by TG-DTA method showing that uranium volatilized completely over 350 °C by the formation of UF6 and the adsorption of plutonium by UO2F2 should be done at temperatures lower than 250 °C. The behavior of PtF6 as a chemical analogue of PuF6 was also conducted for comparison and it showed that the deposition of PtF4 on UO2F2 at 200 °C. When the 236Pu doped U3O8 was reacted with 10%F2-He gas, the PuF6 vaporized at ca. 600 °C. Then adsorption of 236Pu on UO2F2 was observed by α ray measurement. The adsorption mechanism of Pu on UO2F2 was discussed with experimental data and thermodynamic consideration.

  4. Improvement of Algorithms for Pressure Maintenance Systems in Drum-Separators of RBMK-1000 Reactors

    SciTech Connect

    Aleksakov, A. N. Yankovskiy, K. I.; Dunaev, V. I.; Kushbasov, A. N.

    2015-05-15

    The main tasks and challenges for pressure regulation in the drum-separators of RBMK-1000 reactors are described. New approaches to constructing algorithms for pressure control in drum-separators by electro-hydraulic turbine control systems are discussed. Results are provided from tests of the operation of modernized pressure regulators during fast transients with reductions in reactor power.

  5. 40 CFR 417.180 - Applicability; description of the manufacture of drum dried detergents subcategory.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... manufacture of drum dried detergents subcategory. 417.180 Section 417.180 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Drum Dried Detergents Subcategory § 417.180...

  6. 40 CFR 417.180 - Applicability; description of the manufacture of drum dried detergents subcategory.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... manufacture of drum dried detergents subcategory. 417.180 Section 417.180 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Drum Dried Detergents Subcategory § 417.180...

  7. 40 CFR 417.180 - Applicability; description of the manufacture of drum dried detergents subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... manufacture of drum dried detergents subcategory. 417.180 Section 417.180 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Drum Dried Detergents Subcategory § 417.180...

  8. 40 CFR 417.180 - Applicability; description of the manufacture of drum dried detergents subcategory.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... manufacture of drum dried detergents subcategory. 417.180 Section 417.180 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Drum Dried Detergents Subcategory § 417.180...

  9. 40 CFR 417.180 - Applicability; description of the manufacture of drum dried detergents subcategory.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... manufacture of drum dried detergents subcategory. 417.180 Section 417.180 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Drum Dried Detergents Subcategory § 417.180...

  10. Bringing Carnaval Drum and Dance Traditions into 4-H Programming for Latino Youth

    ERIC Educational Resources Information Center

    Conklin-Ginop, Evelyn; Braverman, Marc T.; Caruso, Robyn; Bone, Dennis

    2011-01-01

    4-H Bloco Drum and Dance is an afterschool program that teaches adolescents drumming, dancing, and theater arts in the rich traditions of Brazilian Carnaval. Teens learn to express themselves in a variety of modalities and perform at community events. The program was developed by a community coalition that included 4-H, other youth programs, and…

  11. Monkey drumming reveals common networks for perceiving vocal and nonvocal communication sounds.

    PubMed

    Remedios, Ryan; Logothetis, Nikos K; Kayser, Christoph

    2009-10-20

    Salient sounds such as those created by drumming can serve as means of nonvocal acoustic communication in addition to vocal sounds. Despite the ubiquity of drumming across human cultures, its origins and the brain regions specialized in processing such signals remain unexplored. Here, we report that an important animal model for vocal communication, the macaque monkey, also displays drumming behavior, and we exploit this finding to show that vocal and nonvocal communication sounds are represented by overlapping networks in the brain's temporal lobe. Observing social macaque groups, we found that these animals use artificial objects to produce salient periodic sounds, similar to acoustic gestures. Behavioral tests confirmed that these drumming sounds attract the attention of listening monkeys similarly as conspecific vocalizations. Furthermore, in a preferential looking experiment, drumming sounds influenced the way monkeys viewed their conspecifics, suggesting that drumming serves as a multimodal signal of social dominance. Finally, by using high-resolution functional imaging we identified those brain regions preferentially activated by drumming sounds or by vocalizations and found that the representations of both these communication sounds overlap in caudal auditory cortex and the amygdala. The similar behavioral responses to drumming and vocal sounds, and their shared neural representation, suggest a common origin of primate vocal and nonvocal communication systems and support the notion of a gestural origin of speech and music. PMID:19805199

  12. Electric-stepping-motor tests for a control-drum actuator of a nuclear reactor

    NASA Technical Reports Server (NTRS)

    Kieffer, A. W.

    1972-01-01

    Experimental tests were conducted on two stepping motors for application as reactor control-drum actuators. Various control-drum loads with frictional resistances ranging from approximately zero to 40 N-m and inertias ranging from zero to 0.424 kg-sq m were tested.

  13. CSER 00-006 Storage of Plutonium Residue Containers in 55 Gallon Drums at the PFP

    SciTech Connect

    DOBBIN, K.D.

    2000-05-24

    This criticality safety evaluation report (CSER) provides the required limit set and controls for safe transit and storage of these drums in the 234-5Z Building at the PFP. A mass limit of 200 g of plutonium or fissile equivalent per drum is acceptable

  14. Motion of a free cylinder inside a rotating water-filled drum

    NASA Astrophysics Data System (ADS)

    Hernández, R. H.; Vial, A.; Barraud, C.

    2015-08-01

    We report experimental results on the motion and levitation of a freely to-move heavy cylinder, of constant diameter and varying mass, inside a water-filled drum rotating around its horizontal axis. The resulting flow field and the cylinder dynamics were determined with the aid of flow visualizations and particle image velocimetry methods. The spatial tracking of the inner cylinder was done with the aid of Fourier cross correlation methods. The steady bulk flow field created by the drum rotation generated forces that make the inner cylinder to counter-rotate without contact with the drum walls. Testing different cylinder masses and rotating drum frequencies has shown that there exists a range of stable spatial positions of the inner cylinder describing an angular segment inside the drum flow. The cylinder frequency can be set to zero if we increase the drum frequency beyond a threshold value. Increasing the drum frequency produces a stronger secondary flow circulation which is the key-mechanism responsible of the counter-rotating cylinder frequency. At this point, the inner cylinder levitates with a constant separation from the drum walls close to half of its diameter. Tests on heavy hollow cylinders revealed that the fluid filling the cylinder remains at rest while the cylinder was under levitation with zero rotation frequency.

  15. Characterization of a Pu-bearing zirconolite-rich synroc

    SciTech Connect

    Buck, E.C.; Ebbinghaus, B.; Bakel, A.J.; Bates, J.K.

    1996-12-31

    A titanate-based ceramic waste form, rich in phases structurally related to zirconolite (CaZrTi{sub 2}O{sub 7}), is being developed as a possible method for immobilizing excess plutonium from dismantled nuclear weapons. As part of this program, Lawrence Livermore National Laboratory (LLNL) produced several ceramics that were then characterized at Argonne National Laboratory (ANL). The plutonium- loaded ceramic was found to contain a Pu-Gd zirconolite phase but also contained plutonium titanates, Gd-polymignyte, and a series of other phases. In addition, much of the Pu was remained as PuO{sub 2- x}. The Pu oxidation state in the zirconolite was determined to be mainly Pu{sup 4+}, although some Pu{sub 3+} was believed to be present.

  16. Iron Corrosion Observations: Pu(VI)-Fe Reduction Studies

    SciTech Connect

    Reed, Donald T.; Swanson, Juliet S.; Richmann, Michael K.; Lucchini, Jean-Francois; Borkowski, Marian

    2012-09-11

    Iron and Pu Reduction: (1) Very different appearances in iron reaction products were noted depending on pH, brine and initial iron phase; (2) Plutonium was associated with the Fe phases; (3) Green rust was often noted at the higher pH; (4) XANES established the green rust to be an Fe2/3 phase with a bromide center; and (5) This green rust phase was linked to Pu as Pu(IV).

  17. Characterization of void volume VOC concentration in vented TRU waste drums - an interim report

    SciTech Connect

    Liekhus, K.J.

    1994-09-01

    A test program is underway at the Idaho National Engineering Laboratory to determine if the concentration of volatile organic compounds (VOCs) in the drum headspace is representative of the VOC concentration in the entire drum void space and to demonstrate that the VOC concentration in the void space of each layer of confinement can be estimated using a model incorporating diffusion and permeation transport principles and limited waste drum sampling data. An experimental test plan was developed requiring gas sampling of 66 transuranic (TRU) waste drums. This interim report summarizes the experimental measurements and model predictions of VOC concentration in the innermost layer of confinement from waste drums sampled and analyzed in FY 1994.

  18. The effect of zebra mussel consumption on growth of freshwater drum in Lake Erie

    USGS Publications Warehouse

    French, John R. P.; Bur, Michael T.

    1996-01-01

    We examined food habits and scale annuli of freshwater drum (Aplodinotus grunniens) from western Lake Erie to determine whether increasing predation on zebra mussels (Dreissena polymorpha) had affected growth of freshwater drum. The volume of zebra mussels in drum guts was greater in older fish. Growth of age classes 3–4, which consumed few zebra mussels, was greater in the most productive year for zebra mussels, July 1990–August 1991, than in three prior years. The total lengths of 5-year-old drum changed little. The mean total length of 6-year-old females has declined since the zebra mussel invaded Lake Erie, even through mussels comprised more than two-thirds of gut samples in these fish. These studies suggest that zebra mussels may not benefit freshwater drum when serving as a staple in the diet. PDF

  19. Comparison exercise on activity determination of radioactive waste drums in Taiwan.

    PubMed

    Chu, Wei-Han; Yeh, Chin-Hsien; Yuan, Ming-Chen

    2016-03-01

    The National Radiation Standard Laboratory of Taiwan organized in 2014 a comparison exercise by distributing 210 L drum-typed samples to seven radioactive waste analysis laboratories in Taiwan. Four drums were filled with uniformly distributed active carbon, water, resin and concrete, respectively and five drums were filled with cracked metals and heterogeneously distributed radioactive sources. Measurement uncertainties of participants results are in the range 3–40% (k=2) and about 96% of the reported results produced En values (ISO, 1997) smaller than one for drums with activity uniformly distributed. The minimum discrepancies, expressed as Bi values (ISO, 1997), of drums with heterogeneously distributed 137Cs and 60Co were 0.34 and 0.17, respectively. PMID:27358943

  20. Potential Vulnerability Issues for Drum-Type Packages

    SciTech Connect

    Hagler, L.B.; Sheaffer, M.K.; Anderson, B.L.; Hafner, R.S.; Witte, M.C.

    2000-05-24

    Type B and Type A fissile drum packages are required to undergo a series of tests that simulate both normal conditions of transport (NCT) and hypothetical accident conditions (HAC) as specified in 10 CFR Part 71. In particular for HAC, it must be demonstrated that the package can withstand a 30 ft. drop in the most unfavorable orientation without damage that would compromise its ability to survive a subsequent regulatory fire test. Historically, it has usually been assumed that the most unfavorable orientations are those that allow the maximum amount of available kinetic energy to be used for package deformation. Therefore, drop test orientations have been mostly limited to Top-Down, Bottom-Down, Side, and C.G. Over Top-Corner. (Where C.G. refers to the center of gravity of the package.) Here, it is shown that shallow angle top impact, where a portion of the translational kinetic energy of the package is transformed into rotational kinetic energy at impact, may also be a likely orientation that will lead to failure of drum packages that use bolted ring closures.

  1. Hanford contact-handled transuranic drum retrieval project planning document

    SciTech Connect

    DEMITER, J.A.

    1998-11-17

    The Hanford Site is one of several US Department of Energy (DOE) sites throughout the US that has generated and stored transuranic (TRU) wastes. The wastes were primarily placed in 55-gallon drums, stacked in trenches, and covered with soil. In 1970, the Nuclear Regulatory Commission ordered that TRU wastes be segregated from other radioactive wastes and placed in retrievable storage until such time that the waste could be sent to a geologic repository and permanently disposed. Retrievable storage also defined container storage life by specifying that a container must be retrievable as a contamination-free container for 20 years. Hanford stored approximately 37,400 TRU containers in 20-year retrievable storage from 1970 to 1988. The Hanford TRU wastes placed in 20-year retrievable storage are considered disposed under existing Resource Conservation and Recovery Act (RCRA) regulations since they were placed in storage prior to September 1988. The majority of containers were 55-gallon drums, but 20-year retrievable storage includes several TRU wastes covered with soil in different storage methods.

  2. Validation testing of radioactive waste drum filter vents

    SciTech Connect

    Weber, L.D.; Rahimi, R.S.; Edling, D.

    1997-08-01

    The minimum requirements for Drum Filter Vents (DFVs) can be met by demonstrating conformance with the Waste Isolation Pilot Plant (WIPP) Trupact II Safety Assessment Report (SAR), and conformance with U.S. Federal shipping regulations 49 CFR 178.350, DOT Spec 7A, for Type A packages. These together address a number of safety related performance parameters such as hydrogen diffusivity, flow related pressure drop, filtration efficiency and, separately, mechanical stability and the ability to prevent liquid water in-leakage. In order to make all metal DFV technology (including metallic filter medium) available to DOE sites, Pall launched a product development program to validate an all metal design to meet these requirements. Numerous problems experienced by DOE sites in the past came to light during this development program. They led us to explore enhancements to DFV design and performance testing addressing these difficulties and concerns. The result is a patented all metal DFV certified to all applicable regulatory requirements, which for the first time solves operational and health safety problems reported by DOE site personnel but not addressed by previous DFV`s. The new technology facilitates operations (such as manual, automated and semi-automated drum handling/redrumming), sampling, on-site storage, and shipping. At the same time, it upgrades filtration efficiency in configurations documented to maintain filter efficiency following mechanical stress. 2 refs., 2 figs., 10 tabs.

  3. Fort Drum integrated resource assessment. Volume 3, Resource assessment

    SciTech Connect

    Dixon, D.R.; Armstrong, P.R.; Daellenbach, K.K.; Dagle, J.E.; Di Massa, F.V.; Elliott, D.B.; Keller, J.M.; Richman, E.E.; Shankle, S.A.; Sullivan, G.P.; Wahlstrom, R.R.

    1992-12-01

    The US Army Forces Command (FORSCOM) has tasked Pacific Northwest Laboratory (PNL) as the lead laboratory supporting the US Department of Energy (DOE) Federal Energy Management Program`s (FEMP) mission to identify, evaluate, and assist in acquiring all cost-effective energy projects at Fort Drum. This is a model program PNL is designing for federal customers served by the Niagara Mohawk Power Company (Niagara Mohawk). It will (1) identify and evaluate all electric and fossil fuel cost-effective energy projects; (2) develop a schedule at each installation for project acquisition considering project type, size, timing, capital requirements, as well as energy and dollar savings; and (3) secure 100% of the financing required to implement electric energy efficiency projects from Niagara Mohawk and have Niagara Mohawk procure the necessary contractors to perform detailed audits and install the technologies. This report provides the results of the fossil fuel and electric energy resource opportunity (ERO) assessments performed by PNL at one of Niagara Mohawk`s primary federal facilities, the FORSCOM Fort Drum facility located near Watertown, New York. It is a companion report to Volume 1, the Executive Summary, and Volume 2, the Baseline Detail.

  4. Effect of equilibration time on Pu desorption from goethite

    DOE PAGES

    Wong, Jennifer C.; Zavarin, Mavrik; Begg, James D.; Kersting, Annie B.; Powell, Brian A.

    2015-01-28

    Strongly sorbing ions such as plutonium may become irreversibly bound to mineral surfaces over time implicates near- and far-field transport of Pu. Batch adsorption–desorption data were collected as a function of time and pH to study the surface stability of Pu on goethite. Pu(IV) was adsorbed to goethite over the pH range 4.2 to 6.6 for different periods of time (1, 6, 15, 34 and 116 d). Moreover, following adsorption, Pu was leached from the mineral surface with desferrioxamine B (DFOB), a complexant capable of effectively competing with the goethite surface for Pu. The amount of Pu desorbed from the goethitemore » was found to vary as a function of the adsorption equilibration time, with less Pu removed from the goethite following longer adsorption periods. This effect was most pronounced at low pH. Logarithmic desorption distribution ratios for each adsorption equilibration time were fit to a pH-dependent model. Model slopes decreased between 1 and 116 d adsorption time, indicating that overall Pu(IV) surface stability on goethite surfaces becomes less dependent on pH with greater adsorption equilibration time. The combination of adsorption and desorption kinetic data suggest that non-redox aging processes affect Pu sorption behavior on goethite.« less

  5. Effect of equilibration time on Pu desorption from goethite

    SciTech Connect

    Wong, Jennifer C.; Zavarin, Mavrik; Begg, James D.; Kersting, Annie B.; Powell, Brian A.

    2015-01-28

    Strongly sorbing ions such as plutonium may become irreversibly bound to mineral surfaces over time implicates near- and far-field transport of Pu. Batch adsorption–desorption data were collected as a function of time and pH to study the surface stability of Pu on goethite. Pu(IV) was adsorbed to goethite over the pH range 4.2 to 6.6 for different periods of time (1, 6, 15, 34 and 116 d). Moreover, following adsorption, Pu was leached from the mineral surface with desferrioxamine B (DFOB), a complexant capable of effectively competing with the goethite surface for Pu. The amount of Pu desorbed from the goethite was found to vary as a function of the adsorption equilibration time, with less Pu removed from the goethite following longer adsorption periods. This effect was most pronounced at low pH. Logarithmic desorption distribution ratios for each adsorption equilibration time were fit to a pH-dependent model. Model slopes decreased between 1 and 116 d adsorption time, indicating that overall Pu(IV) surface stability on goethite surfaces becomes less dependent on pH with greater adsorption equilibration time. The combination of adsorption and desorption kinetic data suggest that non-redox aging processes affect Pu sorption behavior on goethite.

  6. Ferro- and antiferro-magnetism in (Np, Pu)BC

    NASA Astrophysics Data System (ADS)

    Klimczuk, T.; Shick, A. B.; Kozub, A. L.; Griveau, J.-C.; Colineau, E.; Falmbigl, M.; Wastin, F.; Rogl, P.

    2015-04-01

    Two new transuranium metal boron carbides, NpBC and PuBC, have been synthesized. Rietveld refinements of powder XRD patterns of {Np,Pu}BC confirmed in both cases isotypism with the structure type of UBC. Temperature dependent magnetic susceptibility data reveal antiferromagnetic ordering for PuBC below TN = 44 K, whereas ferromagnetic ordering was found for NpBC below TC = 61 K. Heat capacity measurements prove the bulk character of the observed magnetic transition for both compounds. The total energy electronic band structure calculations support formation of the ferromagnetic ground state for NpBC and the antiferromagnetic ground state for PuBC.

  7. Synchronized Drumming Enhances Activity in the Caudate and Facilitates Prosocial Commitment - If the Rhythm Comes Easily

    PubMed Central

    Kokal, Idil; Engel, Annerose; Kirschner, Sebastian; Keysers, Christian

    2011-01-01

    Why does chanting, drumming or dancing together make people feel united? Here we investigate the neural mechanisms underlying interpersonal synchrony and its subsequent effects on prosocial behavior among synchronized individuals. We hypothesized that areas of the brain associated with the processing of reward would be active when individuals experience synchrony during drumming, and that these reward signals would increase prosocial behavior toward this synchronous drum partner. 18 female non-musicians were scanned with functional magnetic resonance imaging while they drummed a rhythm, in alternating blocks, with two different experimenters: one drumming in-synchrony and the other out-of-synchrony relative to the participant. In the last scanning part, which served as the experimental manipulation for the following prosocial behavioral test, one of the experimenters drummed with one half of the participants in-synchrony and with the other out-of-synchrony. After scanning, this experimenter “accidentally” dropped eight pencils, and the number of pencils collected by the participants was used as a measure of prosocial commitment. Results revealed that participants who mastered the novel rhythm easily before scanning showed increased activity in the caudate during synchronous drumming. The same area also responded to monetary reward in a localizer task with the same participants. The activity in the caudate during experiencing synchronous drumming also predicted the number of pencils the participants later collected to help the synchronous experimenter of the manipulation run. In addition, participants collected more pencils to help the experimenter when she had drummed in-synchrony than out-of-synchrony during the manipulation run. By showing an overlap in activated areas during synchronized drumming and monetary reward, our findings suggest that interpersonal synchrony is related to the brain's reward system. PMID:22110623

  8. Measurement of plutonium isotopes, 239Pu and 240Pu, in air-filter samples from Seville (2001-2002)

    NASA Astrophysics Data System (ADS)

    Chamizo, E.; García-León, M.; Enamorado, S. M.; Jiménez-Ramos, M. C.; Wacker, L.

    2010-05-01

    Since the last nuclear atmospheric test carried out by the People Republic of China in 1980 and since the Chernobyl accident in 1986, the plutonium hasn't been directly released into the atmosphere. However, nowadays, it is still present in the troposphere. This is due to plutonium-bearing soil particles physical resuspension processes. In this work, we study for the first time the temporal variation of plutonium isotopes, 239Pu and 240Pu, baseline concentrations on a monthly basis in surface air from Seville (Spain), and their correlation with some tracers of mineral dust, during 2001 and 2002. The Pu analyses were performed by low-energy Accelerator Mass Spectrometry (AMS). The 239Pu plus 240Pu ( 239+240Pu) activity levels achieved maximums during the summer period, characterized by the absence of rains, and minimums during the rainy seasons, laying in the range 1-20 nBq m -3. The 240Pu/ 239Pu two-year average atomic ratio was 0.18 ± 0.03, in agreement with the fallout plutonium. A good correlation with Pu and Al and Ti levels is observed. They are crustal components usually used as tracers of African dust over European countries. The hypothesis of the influence of the Saharan dust intrusions is supported as well through the study of Total Ozone Mass Spectrometer (TOMS) daily images.

  9. Free energy of formation of Cs 3PuCl 6 and CsPu 2Cl 7

    NASA Astrophysics Data System (ADS)

    Williamson, M. A.; Kleinschmidt, P. D.

    The free energy, enthalpy and entropy of formation of the compounds Cs 3PuCl 6 and CsPu 2Cl 7 have been determined by measuring the sublimation pressures for the reactions CsCl( s) / aiCsCl( g), {2}/{5}Cs 3PuCl 6(s) /ai {1}/{5}CsPu 2Cl 7(s) + CsCl(g) , and CsPu2Cl7( s) / ai 2 PuCl3( s) + CsCl( g). The pressures are measured using Knudsen effusion mass spectrometry over the temperature range 600 to 850 K. For the formation of Cs 3PuCl 6 from CsCl and PuCl 3, ΔG0298 = -77.3 ± 8.5 kJ/ mol, ΔH0298 = -82.1 ± 7.8 kJ/ mol, and ΔS0298 = -16.2 ± 10.9 J/ Kmol. For CsPu 2Cl 7, ΔG0298 = -39.4 ± 3.5 kJ/ mol, ΔH0298 = -40.8 ± 3.2 kJ/ mol, and ΔS0298 = -4.6 ± 4.2 J/ Kmol.

  10. Granular flow in a rotating drum: Experiments and theory

    NASA Astrophysics Data System (ADS)

    Hung, C. Y.; Stark, C. P.; Capart, H.; Li, L.; Smith, B.; Grinspun, E.

    2015-12-01

    Erosion at the base of a debris flow fundamentally controls how large the flow will become and how far it will travel. Experimental observations of this important phenomenon are rather limited, and this lack has led theoretical treatments to making ad hoc assumptions about the basal process. In light of this, we carried out a combination of laboratory experiments and theoretical analysis of granular flow in a rotating drum, a canonical example of steady grain motion in which entrainment rates can be precisely controlled. Our main result is that basal sediment is entrained as the velocity profile adjusts to imbalance in the flow of kinetic energy.Our experimental apparatus consisted of a 40cm-diameter drum, 4cm-deep, half-filled with 2.3mm grains. Rotation rates varied from 1-70 rpm. We varied the effective scale by varying effective gravity from 1g to 70g on a geotechnical centrifuge. The field of grain motion was recorded using high-speed video and mapped using particle tracking velocimetry. In tandem we developed a depth-averaged theory using balance equations for mass, momentum and kinetic energy. We assumed a linearized GDR Midi granular rheology [da Cruz, 2005] and a Coulomb friction law along the sidewalls [Jop et al., 2005]. A scaling analysis of our equations yields a dimensionless "entrainment number" En, which neatly parametrizes the flow geometry in the drum for a wide range of variables, e.g., rotation rate and effective gravity. At low En, the flow profile is planar and kinetic energy is balanced locally in the flow layer. At high En, the flow profile is sigmoidal (yin-yang shaped) and the kinetic energy is dominated by longitudinal, streamwise transfer. We observe different scaling behavior under each of these flow regimes, e.g., between En and kinetic energy, surface slope and flow depth. Our theory correctly predicts their scaling exponents and the value of En at which the regime transition takes place. We are also able to make corrections for

  11. Is Octavalent Pu(VIII) Possible? Mapping the Plutonium Oxyfluoride Series PuO(n)F(8-2n) (n = 0-4).

    PubMed

    Huang, Wei; Pyykkö, Pekka; Li, Jun

    2015-09-01

    While the oxidation state Pu(VIII) is shown to be less stable than Pu(V) in the PuO4 molecule, it is not clear if the more electronegative fluorine can help to stabilize Pu(VIII). Our calculations on PuO(n)F(8-2n) (n = 0-4) molecules notably confirm that PuO2F4 has both (1)D(4h) and (5)C(2v) minima with the oxidation states Pu(VIII) and Pu(V), respectively, with the latter having lower energy. The hybrid-DFT, CCSD(T), and CASSCF methods all give the same result. The results conform to a superoxide ligand when n ≥ 2. PuF8 in a (1)O(h) state can decompose to PuF6 and F2, and PuOF6 in a (1)C(2v) state also can break down to PuF6 and 1/2 O2. The Pu(VIII) anion PuO2F5(-) does have a D(5h) minimum, which also lies above a (5)C(2v) Pu(V) peroxide structure. However, the energy differences between the different minima are not large, indicating that metastable species with oxidation states higher than Pu(V) cannot be completely excluded.

  12. Development of a model for predicting transient hydrogen venting in 55-gallon drums

    SciTech Connect

    Apperson, Jason W; Clemmons, James S; Garcia, Michael D; Sur, John C; Zhang, Duan Z; Romero, Michael J

    2008-01-01

    Remote drum venting was performed on a population of unvented high activity drums (HAD) in the range of 63 to 435 plutonium equivalent Curies (PEC). These 55-gallon Transuranic (TRU) drums will eventually be shipped to the Waste Isolation Pilot Plant (WIPP). As a part of this process, the development of a calculational model was required to predict the transient hydrogen concentration response of the head space and polyethylene liner (if present) within the 55-gallon drum. The drum and liner were vented using a Remote Drum Venting System (RDVS) that provided a vent sampling path for measuring flammable hydrogen vapor concentrations and allow hydrogen to diffuse below lower flammability limit (LFL) concentrations. One key application of the model was to determine the transient behavior of hydrogen in the head space, within the liner, and the sensitivity to the number of holes made in the liner or number of filters. First-order differential mass transport equations were solved using Laplace transformations and numerically to verify the results. the Mathematica 6.0 computing tool was also used as a validation tool and for examining larger than two chamber systems. Results will be shown for a variety of configurations, including 85-gallon and 110-gallon overpack drums. The model was also validated against hydrogen vapor concentration assay measurements.

  13. Ruffed grouse (Bonasa umbellus) drumming log and habitat use in Grand Teton National Park, Wyoming

    USGS Publications Warehouse

    Buhler, M.L.; Anderson, S.H.

    2001-01-01

    We described 15 Ruffed Grouse (Bonasa umbellus) drumming logs and adjacent habitat within Grand Teton National Park, Wyoming. Drumming logs and adjacent habitat differed from 30 random non-drumming sites. Drumming logs had fewer limbs (8; P = 0.003) and a smaller percentage of bark remaining (12%; P = 0.0001). These logs were in advanced stages of decay but were still firm to the touch. Additionally, drumming logs were found close to clearings but in areas with increased amounts of undergrowth and mature trees. Adjacent habitat analysis (0.04-ha circular plot centered on logs) indicated drumming locations had significantly greater average canopy height, more vegetative cover consisting of conifer and total canopy cover, and more vertical foliage between 0.3 m and 3.0 m in height. Adjacent habitat was in advanced stages of maturity as indicated by significant numbers of both large-diameter logs and large-diameter lodgepole pine (Pinus contorta) and quaking aspen (Populus tremuloides) snags. Tree species dominating the canopy and subcanopy were large-diameter Engelmann spruce (Picea engelmannii), lodgepole pine, and quaking aspen. Subalpine fir (Abies lasiocarpa) and quaking aspen saplings were more numerous at used sites. Ruffed Grouse drummed in coniferous areas within close proximity of quaking aspen.

  14. Variation in movement patterns of red drum (Sciaenops ocellatus) inferred from conventional tagging and ultrasonic telemetry

    USGS Publications Warehouse

    Bacheler, N.M.; Paramore, L.M.; Burdick, S.M.; Buckel, J.A.; Hightower, J.E.

    2009-01-01

    We used 25 years of conventional tagging data (n=6173 recoveries) and 3 years of ultrasonic telemetry data (n=105 transmitters deployed) to examine movement rates and directional preferences of four age classes of red drum (Sciaenops ocellatus) in estuarine and coastal waters of North Carolina. Movement rates of conventionally tagged red drum were dependent on the age, region, and season of tagging. Age-1 and age-2 red drum tagged along the coast generally moved along the coast, whereas fish tagged in oligohaline waters far from the coast were primarily recovered in coastal regions in fall months. Adult (age-4+) red drum moved from overwintering grounds on the continental shelf through inlets into Pamlico Sound in spring and summer months and departed in fall. Few tagged red drum were recovered in adjacent states (0.6% of all recoveries); however, some adult red drum migrated seasonally from overwintering grounds in coastal North Carolina northward to Virginia in spring, returning in fall. Age-2 transmittertracked red drum displayed seasonal emigration from a small tributary, but upstream and downstream movements within the tributary were correlated with fluctuating salinity regimes and not season. Large-scale conventional tagging and ultrasonic telemetry programs can provide valuable insights into the complex movement patterns of estuarine fish.

  15. PU.1 silencing leads to terminal differentiation of erythroleukemia cells

    SciTech Connect

    Atar, Orna; Levi, Ben-Zion . E-mail: blevi@technion.ac.il

    2005-04-22

    The transcription factor PU.1 plays a central role in development and differentiation of hematopoietic cells. Evidence from PU.1 knockout mice indicates a pivotal role for PU.1 in myeloid lineage and B-lymphocyte development. In addition, PU.1 is a key player in the development of Friend erythroleukemia disease, which is characterized by proliferation and differentiation arrest of proerythrocytes. To study the role of PU.1 in erythroleukemia, we have used murine erythroleukemia cells, isolated from Friend virus-infected mice. Expression of PU.1 small interfering RNA in these cells led to significant inhibition of PU.1 levels. This was accompanied by inhibition of proliferation and restoration in the ability of the proerythroblastic cells to produce hemoglobin, i.e., reversion of the leukemic phenotype. The data suggest that overexpression of PU.1 gene is the immediate cause for maintaining the leukemic phenotype of the disease by retaining the self-renewal capacity of transformed erythroblastic cells and by blocking the terminal differentiation program towards erythrocytes.

  16. Pu-238 fuel form activities, January 1-31, 1982

    SciTech Connect

    Not Available

    1982-03-01

    This monthly report for /sup 238/Pu fuel form activities has two main sections: SRP-PuFF facility and SRL fuel form activities. The program status, budget information, and milestone schedules are discussed in each main section. The Work Breakdown Structure (WBS) for this program is shown. Only one monthly report per year is processed for EDB.

  17. Pu-238 fuel form activities, January 1-31, 1981

    SciTech Connect

    Not Available

    1981-02-01

    This monthly report for /sup 238/Pu Fuel Form Activities has two main sections: SRP-PuFF facility and SRL Fuel Form Activities. The program status, budget information, and milestone schedules are discussed in each main section. The Work Breakdown Structure (WBS) for this program is shown. Only one monthly report per year is processed for EDB.

  18. Pu-238 fuel form activities, January 1-31, 1983

    SciTech Connect

    Not Available

    1983-03-01

    This monthly report for /sup 238/Pu Fuel Form Activities has two main sections: SRP-PuFF facility and SRL Fuel Form Activities. The program status, budget information, and milestone schedules are discussed in each main section. The Work Breakdown Structure (WBS) for this program is shown. Only one monthly report per year is processed for EDB.

  19. Nondestructive testing methods for 55-gallon, waste storage drums

    SciTech Connect

    Ferris, R.H.; Hildebrand, B.P.; Hockey, R.L.; Riechers, D.M.; Spanner, J.C.; Duncan, D.R.

    1993-06-01

    The Westinghouse Hanford Company (WHC) authorized Pacific Northwest Laboratory (PNL) to conduct a feasibility study to identify promising nondestructive testing (NDT) methods for detecting general and localized (both pitting and pinhole) corrosion in the 55-gal drums that are used to store solid waste materials at the Hanford Site. This document presents results obtained during a literature survey, identifies the relevant reference materials that were reviewed, provides a technical description of the methods that were evaluated, describes the laboratory tests that were conducted and their results, identifies the most promising candidate methods along with the rationale for these selections, and includes a work plan for recommended follow-on activities. This report contains a brief overview and technical description for each of the following NDT methods: magnetic testing techniques; eddy current testing; shearography; ultrasonic testing; radiographic computed tomography; thermography; and leak testing with acoustic detection.

  20. Continuum theory of axial segregation in a long rotating drum

    SciTech Connect

    Aranson, I.S.; Vinokur, V.M.; Tsimring, L.S.

    1999-08-01

    We develop a continuum description for the axial segregation of granular materials in a long rotating drum based on the dynamics of the thin near-surface granular flow coupled to bulk flow. The equations of motion are reduced to the one-dimensional system for two local variables only, the concentration difference and the dynamic angle of repose, or the average slope of the free surface. The parameters of the system are established from comparison with experimental data. The resulting system describes both initial transient traveling wave dynamics and the formation of quasi-stationary bands of segregated materials. A long-term evolution proceeds through slow logarithmic coarsening of the band structure which is analogous to the spinoidal decomposition described by the Cahn-Hilliard equation. {copyright} {ital 1999} {ital The American Physical Society}

  1. Passive neutron design study for 200-L waste drums

    SciTech Connect

    Menlove, H.O.; Beddingfield, D.B.; Pickrell, M.M.

    1997-09-01

    We have developed a passive neutron counter for the measurement of plutonium in 200-L drums of scrap and waste. The counter incorporates high efficiency for the multiplicity counting in addition to the traditional coincidence counting. The {sup 252}Cf add-a-source feature is used to provide an accurate assay over a wide range of waste matrix materials. The room background neutron rate is reduced by using 30 cm of external polyethylene shielding and the cosmic-ray background is reduced by statistical filtering techniques. Monte Carlo Code calculations were used to determine the optimum detector design, including the gas pressure, size, number, and placement of the {sup 3}He tubes in the moderator. Various moderators, including polyethylene, plastics, teflon, and graphite, were evaluated to obtain the maximum efficiency and minimum detectable mass of plutonium.

  2. A thermal analysis for the use of cooled rotating drums in electron processing

    NASA Astrophysics Data System (ADS)

    Fletcher, P. Michael; Williams, Kenneth E.

    The thermal response of rotating drums under an electron beam has been analyzed using a finite difference thermal analysis computer code. Rotating drums are used to convey thin webs or films under the electron beams while controlling their temperature and, in some cases, in dissipating the exotherm involved in curing coatings applied to them. Each portion of the drum surface receives one heat pulse per rotation as it passes under the beam. The drum's thermal behavior shows both an immediate response to each heat pulse and a more gradual response to the average heat acquired over many pulses. After many rotations a steady state is reached where there is only an immediate response to each heat pulse but the gradual heating has tapered off. Nevertheless the steady state temperatures are strongly dependent on the gradual heating that led to them. Slow and fast speeds of rotation are compared showing the effects of both gradual and immediate heating components. The thermal analysis is extended to include the coolant fluid inside the drum shell and the web on the drum surface. The coolant's incoming temperature, volumetric flow rate, flow speed through the coolant channels and film coefficient between the outer shell and fluid are all included in the analysis. The small air gap between the web and drum, the convective cooling of the web to the ambient air, and the exothermic reaction of any chemical reactions on the web are included. The stresses produced in the drum shell (i.e. between the outer surface and the temperature-controlling fluid within the drum) are analyzed in order to define safe e-beam powers and rotating speeds. The analysis provides the basis for many design decisions and can give an end-user a full temperature history for his product for any set of conditions.

  3. A genetic linkage map of red drum, Sciaenops ocellatus.

    PubMed

    Portnoy, D S; Renshaw, M A; Hollenbeck, C M; Gold, J R

    2010-12-01

    Second-generation, sex-specific genetic linkage maps were generated for the economically important estuarine-dependent marine fish Sciaenops ocellatus (red drum). The maps were based on F(1) progeny from each of two single-pair mating families. A total of 237 nuclear-encoded microsatellite markers were mapped to 25 linkage groups. The female map contained 226 markers, with a total length of 1270.9 centiMorgans (cM) and an average inter-marker interval of 6.53 cM; the male map contained 201 markers, with a total length of 1122.9 cM and an average inter-marker interval of 6.03 cM. The overall recombination rate was approximately equal in the two sexes (♀:♂=1.03:1). Recombination rates in a number of linkage intervals, however, differed significantly between the same sex in both families and between sexes within families. The former occurred in 2.4% of mapped intervals, while the latter occurred in 51.2% of mapped intervals. Sex-specific recombination rates varied within chromosomes, with regions of both female-biased and male-biased recombination. Original clones from which the microsatellite markers were generated were compared with genome sequence data for the spotted green puffer, Tetraodon nigroviridis; a total of 43 matches were located in 17 of 21 chromosomes of T. nigroviridis, while seven matches were in unknown portions of the T. nigroviridis genome. The map for red drum provides a new, useful tool for aquaculture, population genetics, and comparative genomics of this economically important marine species. PMID:20477786

  4. Drum silencer with shallow cavity filled with helium.

    PubMed

    Choy, Y S; Huang, Lixi

    2003-09-01

    The motivation of this study is twofold: (a) to produce a flow-through silencer with zero pressure loss for pressure-critical applications, and (b) to tackle low frequency noise with limited sideway space using cavities filled with helium. The work represents a further development of our recently conceived device of a drum-like silencer with conventional air cavity [Huang, J. Acoust. Soc. Am. 112, 2014-2025 (2002); Choy and Huang, ibid. 112, 2026-2035 (2002)]. Theoretical predictions are validated by experimental data. The new silencer consists of two highly tensioned membranes lining part of a duct, and each membrane is backed by a cavity filled with helium. For a typical configuration of a duct with height h, membrane length L = 7h, cavity depth h = 0.2h, and tension T = 0.52rho0c0(2)h2, where rho0 and c0 are the ambient density and speed of sound in air, respectively, the transmission loss has a continuous stop band of TL > 6.35 dB for frequency 0.03c0/h to 0.064c0/h, which is much better than traditional duct lining. In addition to the mechanisms at work for drum silencers with air cavity, the low density of helium reduces the masslike reactance of the cavity on the second in vacuo mode of membrane vibration. The reduction greatly enhances the membrane response at this mode, which is found to be critical for achieving a broadband performance in the low-frequency regime.

  5. Drum silencer with shallow cavity filled with helium

    NASA Astrophysics Data System (ADS)

    Choy, Y. S.; Huang, Lixi

    2003-09-01

    The motivation of this study is twofold: (a) to produce a flow-through silencer with zero pressure loss for pressure-critical applications, and (b) to tackle low frequency noise with limited sideway space using cavities filled with helium. The work represents a further development of our recently conceived device of a drum-like silencer with conventional air cavity [Huang, J. Acoust. Soc. Am. 112, 2014-2025 (2002); Choy and Huang, ibid. 112, 2026-2035 (2002)]. Theoretical predictions are validated by experimental data. The new silencer consists of two highly tensioned membranes lining part of a duct, and each membrane is backed by a cavity filled with helium. For a typical configuration of a duct with height h, membrane length L=7h, cavity depth hc=0.2h, and tension T=0.52ρ0c02h2, where ρ0 and c0 are the ambient density and speed of sound in air, respectively, the transmission loss has a continuous stop band of TL>6.35 dB for frequency 0.03c0/h to 0.064c0/h, which is much better than traditional duct lining. In addition to the mechanisms at work for drum silencers with air cavity, the low density of helium reduces the masslike reactance of the cavity on the second in vacuo mode of membrane vibration. The reduction greatly enhances the membrane response at this mode, which is found to be critical for achieving a broadband performance in the low-frequency regime.

  6. Thermal stabilization of superconducting sigma strings and their drum vortons

    NASA Astrophysics Data System (ADS)

    Carter, Brandon; Brandenberger, Robert H.; Davis, Anne-Christine

    2002-05-01

    We discuss various issues related to stabilized embedded strings in a thermal background. In particular, we demonstrate that such strings will generically become superconducting at moderately low temperatures, thus enhancing their stability. We then present a new class of defects-drum vortons-which arise when a small symmetry breaking term is added to the potential. We display these points within the context of the O(4) sigma model, relevant for hadrodynamics below the QCD scale. This model admits ``embedded defects'' (topological defect configurations of a simpler-in this case O(2) symmetric-model obtained by imposing an embedding constraint) that are unstable in the full model at zero temperature, but that can be stabilized (by electromagnetic coupling to photons) in a thermal gas at moderately high termperatures. It is shown here that below the embedded defect stabilization threshold, there will still be stabilized cosmic string defects. However, they will not be of the symmetric embedded vortex type, but of an ``asymmetric'' vortex type, and are automatically superconducting. In the presence of weak symmetry breaking terms, such as arise naturally when using the O(4) model for hadrodynamics, the strings become the boundary of a new kind of cosmic sigma membrane, with tension given by the pion mass. The string current would then make it possible for a loop to attain a (classically) stable equilibrium state that differs from an ``ordinary'' vorton state by the presence of a sigma membrane stretched across it in a drum-like configuration. Such defects will however be entirely destabilized if the symmetry breaking is too strong, as is found to be the case-due to the rather large value of the pion mass-in the hadronic application of the O(4) sigma model.

  7. MULTIPLE INPUT BINARY ADDER EMPLOYING MAGNETIC DRUM DIGITAL COMPUTING APPARATUS

    DOEpatents

    Cooke-Yarborough, E.H.

    1960-12-01

    A digital computing apparatus is described for adding a plurality of multi-digit binary numbers. The apparatus comprises a rotating magnetic drum, a recording head, first and second reading heads disposed adjacent to the first and second recording tracks, and a series of timing signals recorded on the first track. A series of N groups of digit-representing signals is delivered to the recording head at time intervals corresponding to the timing signals, each group consisting of digits of the same significance in the numbers, and the signal series is recorded on the second track of the drum in synchronism with the timing signals on the first track. The multistage registers are stepped cyclically through all positions, and each of the multistage registers is coupled to the control lead of a separate gate circuit to open the corresponding gate at only one selected position in each cycle. One of the gates has its input coupled to the bistable element to receive the sum digit, and the output lead of this gate is coupled to the recording device. The inputs of the other gates receive the digits to be added from the second reading head, and the outputs of these gates are coupled to the adding register. A phase-setting pulse source is connected to each of the multistage registers individually to step the multistage registers to different initial positions in the cycle, and the phase-setting pulse source is actuated each N time interval to shift a sum digit to the bistable element, where the multistage register coupled to bistable element is operated by the phase- setting pulse source to that position in its cycle N steps before opening the first gate, so that this gate opens in synchronism with each of the shifts to pass the sum digits to the recording head.

  8. Fission xenon from extinct Pu-244 in 14,301.

    NASA Technical Reports Server (NTRS)

    Drozd, R.; Hohenberg, C. M.; Ragan, D.

    1972-01-01

    Xenon extracted in step-wise heating of lunar breccia 14,301 contains a fission-like component in excess of that attributable to uranium decay during the age of the solar system. There seems to be no adequate source for this component other than Pu-244. Verification that this component is in fact due to the spontaneous fission of extinct Pu-244 comes from the derived spectrum which is similar to that observed from artificially produced Pu-244. It thus appears that Pu-244 was extant at the time lunar crustal material cooled sufficiently to arrest the thermal diffusion of xenon. Subsequent history has apparently maintained the isotopic integrity of plutonium fission xenon. Of major importance are details of the storage itself. Either the fission component is the result of in situ fission of Pu-244 and subsequent storage in 14,301 material, or the fission xenon was stored in an intermediate reservoir before incorporation into 14,301.

  9. Sputtering yield of Pu bombarded by fission Fragments from Cf

    SciTech Connect

    Danagoulian, Areg; Klein, Andreas; Mcneil, Wendy V; Yuan, Vincent W

    2008-01-01

    We present results on the yield of sputtering of Pu atoms from a Pu foil, bombarded by fission fragments from a {sup 252}Cf source in transmission geometry. We have found the number of Pu atoms/incoming fission fragments ejected to be 63 {+-} 1. In addition, we show measurements of the sputtering yield as a function of distance from the central axis, which can be understood as an angular distribution of the yield. The results are quite surprising in light of the fact that the Pu foil is several times the thickness of the range of fission fragment particles in Pu. This indicates that models like the binary collision model are not sufficient to explain this behavior.

  10. Spatial distribution of (241)Am, (137)Cs, (238)Pu, (239,240)Pu and (241)Pu over 17 year periods in the Ravenglass saltmarsh, Cumbria, UK.

    PubMed

    Oh, J-S; Warwick, P E; Croudace, I W

    2009-01-01

    Ninety five surface scrape samples were collected at the Ravenglass saltmarsh and analysed for radionuclides by alpha spectrometry ((238)Pu and (239,240)Pu), gamma spectrometry ((241)Am and (137)Cs) and liquid scintillation counting ((241)Pu). Both (241)Am and (137)Cs activities are compared with those reported by Horrill [1983. Concentrations and spatial distribution of radioactivity in an ungrazed saltmarsh. In: Coughtrey, P.J. (Ed.), Ecological Aspects of Radionuclide Release. British Ecological Society Special Publication No. 3. Blackwell, Oxford, pp. 119-215.] Significant decreases in activities for both radionuclides were observed which is caused by the declining levels of discharges from the Sellafield nuclear reprocessing plant since the 1980s. It has been concluded that the spatial distribution of these radionuclides are controlled by the tidal currents and the clay contents in the sediments. There is evidence of surface erosion of the saltmarsh and redistribution of radionuclides in the saltmarsh using isotopic ratios of measured Pu.

  11. Spatial distribution of (241)Am, (137)Cs, (238)Pu, (239,240)Pu and (241)Pu over 17 year periods in the Ravenglass saltmarsh, Cumbria, UK.

    PubMed

    Oh, J-S; Warwick, P E; Croudace, I W

    2009-01-01

    Ninety five surface scrape samples were collected at the Ravenglass saltmarsh and analysed for radionuclides by alpha spectrometry ((238)Pu and (239,240)Pu), gamma spectrometry ((241)Am and (137)Cs) and liquid scintillation counting ((241)Pu). Both (241)Am and (137)Cs activities are compared with those reported by Horrill [1983. Concentrations and spatial distribution of radioactivity in an ungrazed saltmarsh. In: Coughtrey, P.J. (Ed.), Ecological Aspects of Radionuclide Release. British Ecological Society Special Publication No. 3. Blackwell, Oxford, pp. 119-215.] Significant decreases in activities for both radionuclides were observed which is caused by the declining levels of discharges from the Sellafield nuclear reprocessing plant since the 1980s. It has been concluded that the spatial distribution of these radionuclides are controlled by the tidal currents and the clay contents in the sediments. There is evidence of surface erosion of the saltmarsh and redistribution of radionuclides in the saltmarsh using isotopic ratios of measured Pu. PMID:19285416

  12. Resolving global versus local/regional Pu sources in the environment using sector ICP-MS

    USGS Publications Warehouse

    Ketterer, M.E.; Hafer, K.M.; Link, C.L.; Kolwaite, D.; Wilson, Jim; Mietelski, J.W.

    2004-01-01

    Sector inductively coupled plasma mass spectrometry is a versatile method for the determination of plutonium activities and isotopic compositions in samples containing this element at fallout levels. Typical detection limits for 239+240Pu are 0.1, 0.02 and 0.002 Bq kg -1Pu for samples sizes of 0.5 g, 3 g, and 50 g of soil, respectively. The application of sector ICP-MS-based Pu determinations is demonstrated in studies in sediment chronology, soil Pu inventory and depth distribution, and the provenance of global fallout versus local or regional Pu sources. A sediment core collected from Sloans Lake (Denver, Colorado, USA) exhibits very similar 137Cs and 239+240Pu activity profiles; 240Pu/239Pu atom ratios indicate possible small influences from the Nevada Test Site and/or the Rocky Flats Environmental Technology Site. An undisturbed soil profile from Lockett Meadow (Flagstaff, Arizona, USA) exhibits an exponential decrease in 239+240Pu activity versus depth; 240Pu/239Pu in the top 3 cm is slightly lower than the global fallout range of 0.180 ?? 0.014 due to possible regional influence of Nevada Test Site fallout. The 239??240Pu inventory at Lockett Meadow is 56 ?? 4 Bq m-2, consistent with Northern Hemisphere mid-latitude fallout. Archived NdF3 sources, prepared from Polish soils, demonstrate that substantial 239+240Pu from the 1986 Chernobyl disaster has been deposited in north eastern regions of Poland; compared to global fallout, Chernobyl Pu exhibits higher abundances of 240Pu and 241Pu. The ratios 240Pu/239pu and 241Pu/239Pu co-vary and range from 0.186-0.348 and 0.0029-0.0412, respectively, in forest soils (241Pu/239Pu = 0.2407??[240Pu/239Pu] - 0.0413; r2 = 0.9924). ?? The Royal Society of Chemistry 2004.

  13. Re-evaluation of the 1995 Hanford Large Scale Drum Fire Test Results

    SciTech Connect

    Yang, J M

    2007-05-02

    A large-scale drum performance test was conducted at the Hanford Site in June 1995, in which over one hundred (100) 55-gal drums in each of two storage configurations were subjected to severe fuel pool fires. The two storage configurations in the test were pallet storage and rack storage. The description and results of the large-scale drum test at the Hanford Site were reported in WHC-SD-WM-TRP-246, ''Solid Waste Drum Array Fire Performance,'' Rev. 0, 1995. This was one of the main references used to develop the analytical methodology to predict drum failures in WHC-SD-SQA-ANAL-501, 'Fire Protection Guide for Waste Drum Storage Array,'' September 1996. Three drum failure modes were observed from the test reported in WHC-SD-WM-TRP-246. They consisted of seal failure, lid warping, and catastrophic lid ejection. There was no discernible failure criterion that distinguished one failure mode from another. Hence, all three failure modes were treated equally for the purpose of determining the number of failed drums. General observations from the results of the test are as follows: {lg_bullet} Trash expulsion was negligible. {lg_bullet} Flame impingement was identified as the main cause for failure. {lg_bullet} The range of drum temperatures at failure was 600 C to 800 C. This is above the yield strength temperature for steel, approximately 540 C (1,000 F). {lg_bullet} The critical heat flux required for failure is above 45 kW/m{sup 2}. {lg_bullet} Fire propagation from one drum to the next was not observed. The statistical evaluation of the test results using, for example, the student's t-distribution, will demonstrate that the failure criteria for TRU waste drums currently employed at nuclear facilities are very conservative relative to the large-scale test results. Hence, the safety analysis utilizing the general criteria described in the five bullets above will lead to a technically robust and defensible product that bounds the potential consequences from postulated

  14. Performance of Cladding on MOX Fuel with Low 240Pu/239Pu Ratio

    SciTech Connect

    McCoy, Kevin; Blanpain, Patrick; Morris, Robert Noel

    2014-01-01

    The U.S. Department of Energy has decided to dispose of a portion of its surplus plutonium by reconstituting it into mixed oxide (MOX) fuel and irradiating it in commercial power reactors. As part of fuel qualification, four lead assemblies were manufactured and irradiated to a maximum fuel rod average burnup of 47.3 MWd/kg heavy metal. This was the world s first commercial irradiation of MOX fuel with a 240Pu/239Pu ratio less than 0.10. Five fuel rods with varying burnups and plutonium contents were selected from one of the assemblies and shipped to Oak Ridge National Laboratory for hot cell examination. This paper discusses the results of those examinations with emphasis on cladding performance. Exams relevant to the cladding included visual and eddy current exams, profilometry, microscopy, hydrogen analysis, gallium analysis, and mechanical testing. There was no discernible effect of the type of MOX fuel on the performance of the cladding.

  15. Distinguishing Pu Metal from Pu Oxide and Determining alpha-ratio using Fast Neutron Counting

    SciTech Connect

    Verbeke, J. M.; Chapline, G. F.; Nakae, L. F.; Prasad, M. K.; Sheets, S. A.; Snyderman, N. J.

    2015-01-07

    We describe a new method for determining the ratio of the rate of (α, n) source neutrons to the rate of spontaneous fission neutrons, the so called α-ratio. This method is made possible by fast neutron counting with liquid scintillator detectors, which can determine the shape of the fast neutron spectrum. The method utilizes the spectral difference between fission spectrum neutrons from Pu metal and the spectrum of (α, n) neutrons from PuO2. Our method is a generalization of the Cifarelli-Hage method for determining keff for fissile assemblies, and also simultaneously determines keff along with the α-ratio.

  16. Internal Corrosion Analysis of Model 9975 Packaging Containing Pu or PuO{sub 2} During Shipping and Storage

    SciTech Connect

    Vormelker, P.

    1999-03-23

    The Materials Consultation Group of SRTC has completed an internal corrosion analysis of the Model 9975 packaging assembly containing either Pu or PuO2 for storage in K Reactor under ambient conditions for a period of 12 years. The 12-year storage period includes two years for shipping and up to ten years for storage.

  17. Oxidation states, geometries, and electronic structures of plutonium tetroxide PuO4 isomers: is octavalent Pu viable?

    PubMed

    Huang, Wei; Xu, Wen-Hua; Su, Jing; Schwarz, W H E; Li, Jun

    2013-12-16

    In neutral chemical compounds, the highest known oxidation state of all elements in the Periodic Table is +VIII. While PuO4 is viewed as an exotic Pu(+VIII) complex, we have shown here that no stable electronic homologue of octavalent RuO4 and OsO4 exists for PuO4, even though Pu has the same number of eight valence electrons as Ru and Os. Using quantum chemical approaches at the levels of quasi-relativistic DFT, MP2, CCSD(T), and CASPT2, we find the ground state of PuO4 as a quintet (5)C2v-(PuO2)(+)(O2)(-) complex with the leading valence configuration of an (f(3))plutonyl(V) unit, loosely coupled to a superoxido (π*(3))O2(-) ligand. This stable isomer is likely detectable as a transient species, while the previously suggested planar (1)D4h-Pu(VIII)O4 isomer is only metastable. Through electronic structure analyses, the bonding and the oxidation states are explained and rationalized. We have predicted the characteristics of the electronic and vibrational spectra to assist future experimental identification of (PuO2)(+)(O2)(-) by IR, UV-vis, and ionization spectroscopy.

  18. Oxidation states, geometries, and electronic structures of plutonium tetroxide PuO4 isomers: is octavalent Pu viable?

    PubMed

    Huang, Wei; Xu, Wen-Hua; Su, Jing; Schwarz, W H E; Li, Jun

    2013-12-16

    In neutral chemical compounds, the highest known oxidation state of all elements in the Periodic Table is +VIII. While PuO4 is viewed as an exotic Pu(+VIII) complex, we have shown here that no stable electronic homologue of octavalent RuO4 and OsO4 exists for PuO4, even though Pu has the same number of eight valence electrons as Ru and Os. Using quantum chemical approaches at the levels of quasi-relativistic DFT, MP2, CCSD(T), and CASPT2, we find the ground state of PuO4 as a quintet (5)C2v-(PuO2)(+)(O2)(-) complex with the leading valence configuration of an (f(3))plutonyl(V) unit, loosely coupled to a superoxido (π*(3))O2(-) ligand. This stable isomer is likely detectable as a transient species, while the previously suggested planar (1)D4h-Pu(VIII)O4 isomer is only metastable. Through electronic structure analyses, the bonding and the oxidation states are explained and rationalized. We have predicted the characteristics of the electronic and vibrational spectra to assist future experimental identification of (PuO2)(+)(O2)(-) by IR, UV-vis, and ionization spectroscopy. PMID:24274785

  19. Preparation of Pu{sup 239} sources

    SciTech Connect

    Holcomb, H.P.

    1988-08-05

    The Separations Technology Laboratory has prepared four sources to be used for calibrating a waste assay system (Passive/Active Neutron Assay) in Building 724-8G (Burial Ground). The four sources contain 0.5, 0.1, 0.05, and 0.01 grams Pu{sup 239}, respectively. The sources were prepared using aliquots from a single solution provided by the Quality Control (QC) group of Laboratories Department. The solution contained weapons-grade plutonium dissolved in nitric acid. Final solution acidity was 3M. Coulometry had been used to obtain a total plutonium content per unit volume. The weight percent of the plutonium isotopes present was obtained via mass spectrometry.

  20. LLNL Workshop on TEM of Pu

    SciTech Connect

    King, W.E.

    1996-09-10

    On Sept. 10, 1996, LLNL hosted a workshop aimed at answering the question: Is it possible to carry out transmission electron microscopy (TEM) on plutonium metal in an electron microscope located outside the LLNL plutonium facility. The workshop focused on evaluation of a proposed plan for Pu microscopy both from a technical and environment, health, and safety point of view. After review and modification of the plan, workshop participants unanimously concluded that: (1) the technical plan is sound, (2) this technical plan, including a proposal for a new TEM, provides significant improvements and unique capabilities compared with the effort at LANL and is therefore complementary, (3) there is no significant environment, health, and safety obstacle to this plan.

  1. Microscopic Calculations of 240Pu Fission

    SciTech Connect

    Younes, W; Gogny, D

    2007-09-11

    Hartree-Fock-Bogoliubov calculations have been performed with the Gogny finite-range effective interaction for {sup 240}Pu out to scission, using a new code developed at LLNL. A first set of calculations was performed with constrained quadrupole moment along the path of most probable fission, assuming axial symmetry but allowing for the spontaneous breaking of reflection symmetry of the nucleus. At a quadrupole moment of 345 b, the nucleus was found to spontaneously scission into two fragments. A second set of calculations, with all nuclear moments up to hexadecapole constrained, was performed to approach the scission configuration in a controlled manner. Calculated energies, moments, and representative plots of the total nuclear density are shown. The present calculations serve as a proof-of-principle, a blueprint, and starting-point solutions for a planned series of more comprehensive calculations to map out a large set of scission configurations, and the associated fission-fragment properties.

  2. Air concentrations of 239Pu and 240Pu and potential radiation doses to persons living near Pu-contaminated areas in Palomares, Spain.

    PubMed

    Iranzo, E; Salvador, S; Iranzo, C E

    1987-04-01

    On 17 January 1966, an accident during a refueling operation resulted in the destruction of an air force KC-135 tanker and a B-52 bomber carrying four thermonuclear weapons. Two weapons, whose parachutes opened, were found intact. The others experienced non-nuclear explosion with some burning and release of the fissile fuel at impact. Joint efforts by the United States and Spain resulted in remedial action and a long-term program to monitor the effectiveness of the cleanup. Air concentrations of 239Pu and 240Pu have been continuously monitored since the accident. The average annual air concentration for each location was used to estimate committed dose equivalents for individuals living and working around the air sampling stations. The average annual 239Pu and 240Pu air concentrations during the 15-y period corresponding to 1966-1980 and the potential committed dose equivalents for various tissues due to the inhalation of the 239Pu and 240Pu average annual air concentration during this period are shown and discussed in the report.

  3. Air concentrations of /sup 239/Pu and /sup 240/Pu and potential radiation doses to persons living near Pu-contaminated areas in Palomares, Spain

    SciTech Connect

    Iranzo, E.; Salvador, S.; Iranzo, C.E.

    1987-04-01

    On 17 January 1966, an accident during a refueling operation resulted in the destruction of an air force KC-135 tanker and a B-52 bomber carrying four thermonuclear weapons. Two weapons, whose parachutes opened, were found intact. The others experienced non-nuclear explosion with some burning and release of the fissile fuel at impact. Joint efforts by the United States and Spain resulted in remedial action and a long-term program to monitor the effectiveness of the cleanup. Air concentrations of /sup 239/Pu and /sup 240/Pu have been continuously monitored since the accident. The average annual air concentration for each location was used to estimate committed dose equivalents for individuals living and working around the air sampling stations. The average annual /sup 239/Pu and /sup 240/Pu air concentrations during the 15-y period corresponding to 1966-1980 and the potential committed dose equivalents for various tissues due to the inhalation of the /sup 239/Pu and /sup 240/Pu average annual air concentration during this period are shown and discussed in the report.

  4. Air concentrations of 239Pu and 240Pu and potential radiation doses to persons living near Pu-contaminated areas in Palomares, Spain.

    PubMed

    Iranzo, E; Salvador, S; Iranzo, C E

    1987-04-01

    On 17 January 1966, an accident during a refueling operation resulted in the destruction of an air force KC-135 tanker and a B-52 bomber carrying four thermonuclear weapons. Two weapons, whose parachutes opened, were found intact. The others experienced non-nuclear explosion with some burning and release of the fissile fuel at impact. Joint efforts by the United States and Spain resulted in remedial action and a long-term program to monitor the effectiveness of the cleanup. Air concentrations of 239Pu and 240Pu have been continuously monitored since the accident. The average annual air concentration for each location was used to estimate committed dose equivalents for individuals living and working around the air sampling stations. The average annual 239Pu and 240Pu air concentrations during the 15-y period corresponding to 1966-1980 and the potential committed dose equivalents for various tissues due to the inhalation of the 239Pu and 240Pu average annual air concentration during this period are shown and discussed in the report. PMID:3570788

  5. Disposition of transuranic residues from plutonium isentropic compression experiment (Pu-ice) conducted at Z machine

    SciTech Connect

    Goyal, Kapil K; French, David M; Humphrey, Betty J; Gluth, Jeffry

    2010-01-01

    In 1992, the U.S. Congress passed legislation to discontinue above- and below-ground testing of nuclear weapons. Because of this, the U.S. Department of Energy (DOE) must rely on laboratory experiments and computer-based calculations to verify the reliability of the nation's nuclear stockpile. The Sandia National Laboratories/New Mexico (SNL/NM) Z machine was developed by the DOE to support its science-based approach to stockpile stewardship. SNL/NM researchers also use the Z machine to test radiation effects on various materials in experiments designed to mimic nuclear explosions. Numerous components, parts, and materials have been tested. These experiments use a variety of radionuclides; however, plutonium (Pu) isotopes with greater than ninety-eight percent enrichment are the primary radionuclides used in the experiments designed for stockpile stewardship. In May 2006, SNL/NM received authority that the Z Machine Isentropic Compression Experiments could commence. Los Alamos National Laboratory (LANL) provided the plutonium targets and loaded the target assemblies, which were fabricated by SNL/NM. LANL shipped the loaded assemblies to SNL/NM for Z machine experiments. Three experiments were conducted from May through July 2006. The residues from each experiment, which weighed up to 913 pounds, were metallic and packaged into a respective 55-gallon drum each. Based on a memorandum of understanding between the two laboratories, LANL provides the plutonium samples and the respective radio-isotopic information. SNL/NM conducts the experiments and provides temporary storage for the drums until shipment to LANL for final waste certification for disposal at the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico. This paper presents a comprehensive approach for documenting generator knowledge for characterization of waste in cooperation with scientists at the two laboratories and addresses a variety of topics such as material control and accountability

  6. Passive neutron assay of heterogeneous waste drums using the segmented Add-a-Source method

    SciTech Connect

    Menlove, H.O.

    1995-07-01

    We have developed passive neutron detectors that include the Add-a-Source (AS) technique to improve the accuracy of the nondestructive assay of plutonium in large waste containers. We have improved the AS by incorporating multiple positions for the {sup 252}Cf source on the exterior of a 200-L drum. The multiple positions give a better coverage of the drum and have the effect of segmenting the matrix as a function of fill height. We have applied the multiposition AS to the assay of drums with heterogeneous matrix combinations of concrete, polyethylene, wood, paper, and metal. The measurement errors caused by the matrix significantly reduced by the AS technique and anomalous shielding material in the drum can be flagged for more detailed investigation.

  7. 77 FR 8255 - Constitution Road Drum Superfund Site, Atlanta, Dekalb County, GA; Notice of Settlement

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-14

    ... AGENCY Constitution Road Drum Superfund Site, Atlanta, Dekalb County, GA; Notice of Settlement AGENCY: Environmental Protection Agency. ACTION: Notice of Settlement. SUMMARY: Under the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), the United States Environmental Protection Agency...

  8. 77 FR 2981 - Constitution Road Drum Superfund Site; Atlanta, Dekalb County, GA; Notice of Settlement

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-20

    ... AGENCY Constitution Road Drum Superfund Site; Atlanta, Dekalb County, GA; Notice of Settlement AGENCY: Environmental Protection Agency. ACTION: Notice of settlement. SUMMARY: Under Section 122(h)(1) of the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), the United States...

  9. Plasma Glucose Levels for Red Drum Sciaenops Ocellatus in a Florida Estuarine Fisheries Reserve

    NASA Technical Reports Server (NTRS)

    Bourtis, Carla M.; Francis-Floyd, Ruth; Boggs, Ashley S P.; Reyier, Eric A.; Stolen, Eric D.; Yanong, Roy P.; Guillette, Louis J., Jr.

    2015-01-01

    Despite the significant value of the southeastern United States' red drum (Sciaenops ocellatus) fishery, there is a lack of clinical blood chemistry data. This was the first study to assess plasma glucose values as an indicator of stress response to evaluate variation and the effect of reproductive activity for wild adult red drum in Florida. Red drum (n=126) were collected from NASA's Kennedy Space Center waters during three reproductive periods in 2011. Samples were obtained from the branchial vessels of the gill arch. Plasma glucose levels were significantly different among reproductive periods, with the highest mean values recorded during the spawning period, September- October (38.23 mg / dL +/- 10.0). The glucose range was 17 - 69 mg / dL. Glucose values were lower during all three periods than previous values recorded for cultured or captive red drum studies. This may indicate that fish from this population were under less stress than other populations previously sampled.

  10. Identification of the fast and thermal neutron characteristics of transuranic waste drums

    SciTech Connect

    Storm, B.H. Jr.; Bramblett, R.L.; Hensley, C.

    1997-11-01

    Fissile and spontaneously fissioning material in transuranic waste drums can be most sensitively assayed using an active and passive neutron assay system such as the Active Passive Neutron Examination and Assay. Both the active and the passive assays are distorted by the presence of the waste matrix and containerization. For accurate assaying, this distortion must be characterized and accounted for. An External Matrix Probe technique has been developed that accomplishes this task. Correlations between in-drum neutron flux measurements and monitors in the Active Passive Neutron Examination and Assay chamber with various matrix materials provide a non-invasive means of predicting the thermal neutron flux in waste drums. Similarly, measures of the transmission of fast neutrons emitted from sources in the drum. Results obtained using the Lockheed Martin Specialty Components Active Passive Neutron Examination and Assay system are discussed. 12 figs., 1 tab.

  11. EVI1 Impairs myelopoiesis by deregulation of PU.1 function.

    PubMed

    Laricchia-Robbio, Leopoldo; Premanand, Kavitha; Rinaldi, Ciro R; Nucifora, Giuseppina

    2009-02-15

    EVI1 is an oncogene inappropriately expressed in the bone marrow (BM) of approximately 10% of myelodysplastic syndrome (MDS) patients. This disease is characterized by severe anemia and multilineage myeloid dysplasia that are thought to be a major cause of mortality in MDS patients. We earlier reported on a mouse model that constitutive expression of EVI1 in the BM led to fatal anemia and myeloid dysplasia, as observed in MDS patients, and we subsequently showed that EVI1 interaction with GATA1 blocks proper erythropoiesis. Whereas this interaction could provide the basis for the erythroid defects in EVI1-positive MDS, it does not explain the alteration of myeloid differentiation. Here, we have examined the expression of several genes activated during terminal myelopoiesis in BM cells and identified a group of them that are altered by EVI1. A common feature of these genes is their regulation by the transcription factor PU.1. We report here that EVI1 interacts with PU.1 and represses the PU.1-dependent activation of a myeloid promoter. EVI1 does not seem to inhibit PU.1 binding to DNA, but rather to block its association with the coactivator c-Jun. After mapping the PU.1-EVI1 interaction sites, we show that an EVI1 point mutant, unable to bind PU.1, restores the activation of PU.1-regulated genes and allows a normal differentiation of BM progenitors in vitro.

  12. Electronic Structure, Localization and 5f Occupancy in Pu Materials

    SciTech Connect

    Joyce, John J.; Beaux, Miles F.; Durakiewicz, Tomasz; Graham, Kevin S.; Bauer, Eric D.; Mitchell, Jeremy N.; Tobash, Paul H.; Richmond, Scott

    2012-05-03

    The electronic structure of delta plutonium ({delta}-Pu) and plutonium compounds is investigated using photoelectron spectroscopy (PES). Results for {delta}-Pu show a small component of the valence electronic structure which might reasonably be associated with a 5f{sup 6} configuration. PES results for PuTe are used as an indication for the 5f{sup 6} configuration due to the presence of atomic multiplet structure. Temperature dependent PES data on {delta}-Pu indicate a narrow peak centered 20 meV below the Fermi energy and 100 meV wide. The first PES data for PuCoIn5 indicate a 5f electronic structure more localized than the 5fs in the closely related PuCoGa{sub 5}. There is support from the PES data for a description of Pu materials with an electronic configuration of 5f{sup 5} with some admixture of 5f{sup 6} as well as a localized/delocalized 5f{sup 5} description.

  13. Preliminary molten salt extraction experiments with dicesium hexachloroplutonate (Cs/sub 2/PuCl/sub 6/)

    SciTech Connect

    Thomas, R.L.; Long, J.L.; Humiston, T.J.; Murray, A.M.

    1989-01-30

    Dicesium hexachloroplutonate was prepared on a 200-gram scale and used as an oxidant in the molten salt extraction process to remove americium from plutonium metal. Single-pass extraction efficiencies exceeding 90% were achieved in molten calcium chloride. 7 refs., 2 figs., 3 tabs.

  14. Measurement of the 242Pu neutron capture cross section

    NASA Astrophysics Data System (ADS)

    Buckner, M. Q.; Wu, C. Y.; Henderson, R. A.; Bucher, B.; Bredeweg, T. A.; Baramsai, B.; Couture, A.; Jandel, M.; Mosby, S.; O'Donnell, J. M.; Ullmann, J. L.; Chyzh, A.; Dance Collaboration

    2015-10-01

    Precision (n,f) and (n, γ) cross sections are important for the network calculations of the radiochemical diagnostic chain for the U.S. DOE's Stockpile Stewardship Program. 242Pu(n, γ) cross section is relevant to the network calculations of Pu and Am. Additionally, new reactor concepts have catalyzed considerable interest in the measurement of improved cross sections for neutron-induced reactions on key actinides. To date, little or no experimental data has been reported on 242Pu(n, γ) for incident neutron energy below 50 keV. A new measurement of the 242Pu(n, γ) reaction was performed with the DANCE together with an improved PPAC for fission-fragment detection at LANSCE during FY14. The relative scale of the 242Pu(n, γ) cross section spans four orders of magnitude for incident neutron energies from thermal to ~ 30 keV. The absolute scale of the 242Pu(n, γ) cross section is set according to the measured 239Pu(n,f) resonance at 7.8 eV; the target was spiked with 239Pu for this measurement. The absolute 242Pu(n, γ) neutron capture cross section is ~ 30% higher than the cross section reported in ENDF for the 2.7 eV resonance. Latest results to be reported. Funded by U.S. DOE Contract No. DE-AC52-07NA27344 (LLNL) and DE-AC52-06NA25396 (LANL). U.S. DOE/NNSA Office of Defense Nuclear Nonproliferation Research and Development. Isotopes (ORNL).

  15. Analysis of dashpot performance for rotating control drums of a lithium cooled fast reactor concept

    NASA Technical Reports Server (NTRS)

    Wenzler, C. J.

    1972-01-01

    A dashpot was incorporated in the design of the drive train of the rotating control drum to prevent shock damage to the control drum and drive train at the termination of a scram action. A rotating vane dashpot using reactor coolant lithium as a damping fluid appears to be the best candidate of the various damping devices explored. A performance analysis, results and discussion of vane type dashpots are presented.

  16. Mercury concentrations in red drum, Sciaenops ocellatus, from estuarine and offshore waters of Florida.

    PubMed

    Adams, Douglas H; Onorato, Gregory V

    2005-03-01

    Dorsal muscle tissue from 712 red drum, Sciaenops ocellatus, from Florida waters were analyzed for total mercury content. Mercury levels detected in these red drum varied but in most study areas were usually lower than regulatory threshold guidelines. Total mercury levels in individual fish from all study areas ranged from 0.020 to 3.6 ppm (wet weight). Total mercury levels detected in red drum from the Florida Keys-Florida Bay area were often higher than those in fish from all other estuarine study areas. Positive relationships between total mercury levels and fish size (length and weight) and fish age were observed in most Florida study areas, indicating that mercury levels tend to increase over time as red drum grow. The majority of large, mature red drum examined contained mercury levels greater than the 0.5-ppm threshold level set by the Florida Department of Health (DOH). Approximately 94% of all adult red drum from offshore waters adjacent to Tampa Bay contained mercury levels greater than or equal to the 0.5-ppm threshold level, and 64% contained levels greater than or equal to the DOH 1.5-ppm "no consumption" level. All fish from this area with mercury levels greater than 1.5 ppm were large individuals (670 mm SL). Eight percent of legal-size red drum from Florida waters contained total mercury levels greater than or equal to the 0.5-ppm threshold level. The majority (52%) of these legal-size fish greater than or equal to 0.5 ppm were from the Florida Keys-Florida Bay area. In the Florida recreational fishery, the current maximum size limit for this species is an effective filter that prevents humans from consuming those red drum with the greatest likelihood of containing high mercury levels. PMID:15757692

  17. 49 CFR 393.47 - Brake actuators, slack adjusters, linings/pads and drums/rotors.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... steering axle of a truck, truck-tractor or bus shall not be less than 4.8 mm (3/16 inch) at the shoe center....6 mm (1/16 inch) or less for hydraulic disc, drum and electric brakes. (2) Non-steering axle brakes... for drum brakes); or less than 3.2 mm (1/8 inch) for disc brakes. Hydraulic or electric...

  18. Elastic properties of gamma-Pu by resonant ultrasound spectroscopy

    SciTech Connect

    Migliori, Albert; Betts, J; Trugman, A; Mielke, C H; Mitchell, J N; Ramos, M; Stroe, I

    2009-01-01

    Despite intense experimental and theoretical work on Pu, there is still little understanding of the strange properties of this metal. We used resonant ultrasound spectroscopy method to investigate the elastic properties of pure polycrystalline Pu at high temperatures. Shear and longitudinal elastic moduli of the {gamma}-phase of Pu were determined simultaneously and the bulk modulus was computed from them. A smooth linear and large decrease of all elastic moduli with increasing temperature was observed. We calculated the Poisson ratio and found that it increases from 0.242 at 519K to 0.252 at 571K.

  19. 239Pu Resonance Evaluation for Thermal Benchmark System Calculations

    NASA Astrophysics Data System (ADS)

    Leal, L. C.; Noguere, G.; de Saint Jean, C.; Kahler, A. C.

    2014-04-01

    Analyses of thermal plutonium solution critical benchmark systems have indicated a deficiency in the 239Pu resonance evaluation. To investigate possible solutions to this issue, the Organisation for Economic Co-operation and Development (OECD) Nuclear Energy Agency (NEA) Working Party for Evaluation Cooperation (WPEC) established Subgroup 34 to focus on the reevaluation of the 239Pu resolved resonance parameters. In addition, the impacts of the prompt neutron multiplicity (νbar) and the prompt neutron fission spectrum (PFNS) have been investigated. The objective of this paper is to present the results of the 239Pu resolved resonance evaluation effort.

  20. Reconstruction of the isotope activity content of heterogeneous nuclear waste drums.

    PubMed

    Krings, Thomas; Mauerhofer, Eric

    2012-07-01

    Radioactive waste must be characterized in order to verify its conformance with national regulations for intermediate storage or its disposal. Segmented gamma scanning (SGS) is a most widely applied non-destructive analytical technique for the characterization of radioactive waste drums. The isotope specific activity content is generally calculated assuming a homogeneous matrix and activity distribution for each measured drum segment. However, real radioactive waste drums exhibit non-uniform isotope and density distributions most affecting the reliability and accuracy of activities reconstruction in SGS. The presence of internal shielding structures in the waste drum contributes generally to a strong underestimation of the activity and this in particular for radioactive sources emitting low energy gamma-rays independently of their spatial distribution. In this work we present an improved method to quantify the activity of spatially concentrated gamma-emitting isotopes (point sources or hot spots) in heterogeneous waste drums with internal shielding structures. The isotope activity is reconstructed by numerical simulations and fits of the angular dependent count rate distribution recorded during the drum rotation in SGS using an analytical expression derived from a geometric model. First results of the improved method and enhancements of this method are shown and are compared to each other as well as to the conventional method which assumes a homogeneous matrix and activity distribution. It is shown that the new model improves the accuracy and the reliability of the activity reconstruction in SGS and that the presented algorithm is suitable with respect to the framework requirement of industrial application.

  1. Waste drum gas generation sampling program at Rocky Flats during FY 1988

    SciTech Connect

    Roggenthen, D.K.; McFeeters, T.L.; Nieweg, R.G.

    1991-02-11

    Rocky Flats Plant Transuranic Waste Drums were sampled for gas composition. Combustibles, plastics, Raschig rings, solidified organic sludge, and solidified inorganic sludge transuranic waste forms were sampled. Plastic bag material and waste samples were also taken from some solidified sludge waste drums. A vacuum system was used to sample each layer of containment inside a waste drum, including individual waste bags. G values (gas generation) were calculated for the waste drums. Analytical results indicate that very low concentrations of potentially flammable or corrosive gas mixtures will be found in vented drums. G(H{sub 2}) was usually below 1.6, while G(Total) was below 4.0. Hydrogen permeability tests on different types of plastic waste bags used at Rocky Flats were also conducted. Polyvinylchloride was slightly more permeable to hydrogen than polyethylene for new or creased material. Permeability of aged material to hydrogen was slightly higher than for new material. Solidified organic and inorganic sludges were sampled for volatile organics. The analytical results from two drums of solidified organic sludges showed concentrations were above detection limits for four of the 36 volatile organics analyzed. The analytical results for four of the five solidified inorganic sludges show that concentrations were below detection limits for all volatile organics analyzed. 3 refs., 5 figs., 2 tabs.

  2. Predation of the zebra mussel (Dreissena polymorpha) by freshwater drum in western Lake Erie

    USGS Publications Warehouse

    French, John R. P.; Bur, Michael T.; Nalepa, Thomas F.; Schloesser, Donald W.

    1992-01-01

    Environmental and economic problems associated with the colonization of zebra mussels (Dreissena polymorpha) in western Lake Erie created a need to investigate control mechanisms. Predation by fishes is one potential means of control, but predation on zebra mussels by native fishes in Lake Erie is unknown. The freshwater drum (Aplodinotus grunniens) is the most likely fish predator since it is the only fish with pharyngeal teeth capable of crushing mollusk shells. In 1990, freshwater drum were collected in western Lake Erie from 9 sites near rocky reefs and 13 sites with silt or sand bottoms, and gut contents were examined. Predation on zebra mussels increased as drum size increased. Small drum (200-249 mm in length) fed mainly on dipterans, amphipods, and small fish; small zebra mussels (375 mm in length) fed almost exclusively on zebra mussels (seasons and locations combined). The smallest drum capable of crushing zebra mussel shells was 265 mm. Since freshwater drum over 375 mm feed heavily on zebra mussels, they may become a possible biological control mechanism for mussels in portions of North America.

  3. PU IMMOBILIZATION - INDUCTION MELTING ND OFFGAS TESTING

    SciTech Connect

    Marra, J

    2006-11-28

    The Cylindrical Induction Melter (CIM) at the Aiken County Technology Laboratory (ACTL) has been operated by the Savannah River National Laboratory (SRNL) to support the Pu Disposition Conceptual Design (CD-0) development effort. The primary purpose of this report is to summarize the offgas sampling tests conducted in the CIM to capture and analyze the particulate and vapors emitted from lanthanide borosilicate (LaBS) Frit X with HfO{sub 2} as a surrogate for PuO{sub 2} and added impurities. In addition, this report describes several initial tests of the CIM for the vitrification of LaBS Frit X with HfO{sub 2}. The activities required to produce Frit X from batch chemical oxides for subsequent milling to yield glass frit of nominally 20 micron particle size are also discussed. The tests with impurities added showed that alkali salts such as NaCl and KCl were substantially emitted into the offgas system as the salt particulate, HCl, or Cl{sub 2}. Retention of Na and K in the glass were about 80 and 55%, respectively. Chloride retention was about 35%; chloride remaining in the glass was 0.29-0.37 wt%. Based on a material balance, approximately 83% of F fed was retained in the glass at about 0.09 wt % (F could not be measured directly at this concentration). Transition metals (Ni, Cu, Fe, Mo, Cr) were also volatilized to varying extents. A very small amount (<0.1 g) of nickel compounds and KCl were found in crystals deposited on the melter offgas line. Overall, about 58-72% of the impurities added were volatilized. Virtually all of the particulate species were collected on the nominal 0.3 {micro}m filter. The particulate evolution rate ranged from 2-8 g/kg glass/h. The particulate was found to be as small as 0.2 {micro}m and have an approximate median size of 0.5 {micro}m. The particulate salt was also found to stick together by forming bridges between particles. Further runs without washable salts are recommended. Measurements of particle size distribution for use in

  4. Computed tomography of human joints and radioactive waste drums

    SciTech Connect

    Ashby, E; Bernardi, R; Hollerbach, K; Logan, C; Martz, H; Roberson, G P

    1999-06-01

    X- and gamma-ray imaging techniques in nondestructive evaluation (NDE) and assay (NDA) have been increasing use in an array of industrial, environmental, military, and medical applications. Much of this growth in recent years is attributed to the rapid development of computed tomography (CT) and the use of NDE throughout the life-cycle of a product. Two diverse examples of CT are discussed. (1) The computational approach to normal joint kinematics and prosthetic joint analysis offers an opportunity to evaluate and improve prosthetic human joint replacements before they are manufactured or surgically implanted. Computed tomography data from scanned joints are segmented, resulting in the identification of bone and other tissues of interest, with emphasis on the articular surfaces. (2) They are developing NDE and NDE techniques to analyze closed waste drums accurately and quantitatively. Active and passive computed tomography (A and PCT) is a comprehensive and accurate gamma-ray NDA method that can identify all detectable radioisotopes present in a container and measure their radioactivity.

  5. Residence time distributions of gas flowing through rotating drum bioreactors.

    PubMed

    Hardin, M T; Howes, T; Mitchell, D A

    2001-07-20

    Residence time distribution studies of gas through a rotating drum bioreactor for solid-state fermentation were performed using carbon monoxide as a tracer gas. The exit concentration as a function of time differed considerably from profiles expected for plug flow, plug flow with axial dispersion, and continuous stirred tank reactor (CSTR) models. The data were then fitted by least-squares analysis to mathematical models describing a central plug flow region surrounded by either one dead region (a three-parameter model) or two dead regions (a five-parameter model). Model parameters were the dispersion coefficient in the central plug flow region, the volumes of the dead regions, and the exchange rates between the different regions. The superficial velocity of the gas through the reactor has a large effect on parameter values. Increased superficial velocity tends to decrease dead region volumes, interregion transfer rates, and axial dispersion. The significant deviation from CSTR, plug flow, and plug flow with axial dispersion of the residence time distribution of gas within small-scale reactors can lead to underestimation of the calculation of mass and heat transfer coefficients and hence has implications for reactor design and scale-up. PMID:11370003

  6. Pallet fire test for steel drum storage on wooden pallets

    SciTech Connect

    Snook, B.L.

    1992-06-19

    A fire test was conducted by the Martin Marietta PORTS Fire Protection Engineering Department on October 3, 1991. This test was designed and set up to simulate a proposed storage configuration. The array consisted of 55-gallon steel drums, filled with noncombustible waste material, placed on wooden pallets stacked three tiers high. Results from the test served as the basis for determining the fire protection requirements for this type of storage. Data acquired from the test indicated that relatively high temperatures were obtained from the ignition source. These readings, taken during short durations throughout the test, were recorded from digital readouts connected to individual thermocouples. The test demonstrated that the wooden pallets did not significantly ignite and basically self-extinguished once the ignition source was consumed. Based upon these findings, storage of this type may be placed in the high bay (70 foot ceilings) sprinklered areas. This is providing that good housekeeping is implemented, large ignition sources are not allowed to be stored or parked in the area, and flammable and combustible liquids and solids are not permitted within the storage zones. The area shall also be designated as a {open_quotes}NO SMOKING{close_quotes} area.

  7. Modeling variations of medium porosity in rotating drum biofilter.

    PubMed

    Yang, Chunping; Chen, Hong; Zeng, Guangming; Yu, Guanlong; Liu, Xianfeng; Zhang, Xiaoming

    2009-01-01

    Rotating drum biofilters (RDBs) mounted with reticulated polyurethane sponge media has showed high removal efficiencies over a long period of time when used for volatile organic compound (VOC) removal. Due to the accumulation of biomass within the sponge medium, the porosity of a filter bed usually changes dynamically, which makes it difficult to predict and to control. In this paper, the porosity of a multi-layer RDB bed was investigated by a diffusion-reaction model in which biofilm growth and decay were taken into account at the pore scale of the sponge medium. Temporal and spatial changes of porosity were studied under various organic loadings and gas empty bed contact times (EBCTs). The porosity of the biofilter bed was assumed to be a function of biofilm thickness, and all the pores were assumed to be uniform. Toluene was selected as the model VOC. The model was solved using numerical methods through the MATLAB software. Results show that the porosity decreased with increased time of operation, increased toluene loading, or decreased gas EBCT value. The porosity in the outermost medium layer was less than that in the inner medium layers. Toluene removal efficiencies and porosities calculated from this model correlated with the experimental data well. Porosity variation was proposed to be an indicator for prediction of biofilter performance in biofilters as a consequence. PMID:18951611

  8. Computed tomography of human joints and radioactive waste drums

    SciTech Connect

    Martz, Harry E.; Roberson, G. Patrick; Hollerbach, Karin; Logan, Clinton M.; Ashby, Elaine; Bernardi, Richard

    1999-12-02

    X- and gamma-ray imaging techniques in nondestructive evaluation (NDE) and assay (NDA) have seen increasing use in an array of industrial, environmental, military, and medical applications. Much of this growth in recent years is attributed to the rapid development of computed tomography (CT) and the use of NDE throughout the life-cycle of a product. Two diverse examples of CT are discussed, 1.) Our computational approach to normal joint kinematics and prosthetic joint analysis offers an opportunity to evaluate and improve prosthetic human joint replacements before they are manufactured or surgically implanted. Computed tomography data from scanned joints are segmented, resulting in the identification of bone and other tissues of interest, with emphasis on the articular surfaces. 2.) We are developing NDE and NDA techniques to analyze closed waste drums accurately and quantitatively. Active and passive computed tomography (A and PCT) is a comprehensive and accurate gamma-ray NDA method that can identify all detectable radioisotopes present in a container and measure their radioactivity.

  9. Limitation of tritium outgassing from tritiated solid waste drums

    SciTech Connect

    Liger, K.; Trabuc, P.; Lefebvre, X.; Troulay, M.; Perrais, C.

    2015-03-15

    In the framework of the development of fusion thermonuclear reactors, tritiated solid waste is foreseen and will have to be managed. The management of tritiated waste implies limitations in terms of activity and tritium degassing. The degassing tritium can be under the form of tritiated hydrogen, tritiated water and, in some specific cases, negligible amount of tritiated volatile organic compound. Hence, considering the major forms of degassing tritium, CEA has developed a mixed-compound dedicated to tritium trapping in drums. Based on several experiments, the foreseen mixed compound is composed of MnO{sub 2}, Ag{sub 2}O, Pt and molecular sieve, the three first species having the ability to convert tritiated hydrogen into tritiated water and the last one acting as a trap for tritiated water. To assess the performance of the trapping mixture, experimental tests were performed at room temperature on tritiated dust composed of beryllium and carbon. It was shown that the metallic oxides mixture used for tritiated hydrogen conversion is efficient and that tritiated water adsorption was limited due to an inefficient regeneration of the molecular sieve prior to its use. Apart from this point, the tritium release from waste was reduced by a factor of 5.5, which can be improved up to 87 if the adsorption step is efficient.

  10. On the electronic configuration in Pu: spectroscopy and theory

    SciTech Connect

    Tobin, J G; Soderlind, P; Landa, A; Moore, K T; Schwartz, A J; Chung, B W; Wall, M; Wills, J M; Eriksson, O; Haire, R; Kutepov, A L

    2006-10-11

    Photoelectron spectroscopy, synchrotron-radiation-based x-ray absorption, electron energy-loss spectroscopy, and density-functional calculations within the mixed-level and magnetic models, together with canonical band theory have been used to study the electron configuration in Pu. These methods suggest a 5f{sup n} configuration for Pu of 5 {le} n < 6, with n {ne} 6, contrary to what has recently been suggested in several publications. We show that the n = 6 picture is inconsistent with the usual interpretation of photoemission and x-ray absorption spectra. Instead, these spectra support the traditional conjecture of a 5f{sup 5} configuration in Pu as is obtained by density-functional theory. We further argue, based on 5f-band filling, that an n = 6 hypothesis is incompatible with the position of Pu in the actinide series and its monoclinic ground-state phase.

  11. Neutron Capture and Fission Measurement on ^238Pu at DANCE

    NASA Astrophysics Data System (ADS)

    Chyzh, Andrii; Wu, Ching-Yen; Kwan, Elaine; Henderson, Roger; Gostic, Jolie; Couture, Aaron; Young, Hye; Ullmann, John; O'Donnell, John; Jandel, Marian; Haight, Robert; Bredeweg, Todd

    2012-10-01

    Neutron capture and fission reactions on actinides are important in nuclear engineering and physics. DANCE (Detector for Advanced Neutron Capture Measurement, LANL) combined with PPAC (avalanche technique based fission tagging detector, LLNL) were used to study the neutron capture reactions in ^238Pu. Because of extreme spontaneous α-radioactivity in ^238Pu and associated safety issues, 3 separate experiments were performed in 2010-2012. The 1st measurement was done without fission tagging on a 396-μg thick target. The 2nd one was with PPAC on the same target. The 3rd final measurement was done on a thin target with a mass of 40 μg in order to reduce α-background load on PPAC. This was the first such measurement in a laboratory environment. The absolute ^238Pu(n,γ) cross section is presented together with the prompt γ-ray multiplicity in the ^238Pu(n,f) reaction.

  12. [239Pu and chromosomal aberrations in human peripheral blood lymphocytes].

    PubMed

    Okladnikova, N D; Osovets, S V; Kudriavtseva, T I

    2009-01-01

    The genome status in somatic cells was assessed using the chromosomal aberration (CA) test in peripheral blood lymphocytes from 194 plutonium workers exposed to occupational radiation mainly from low-transportable compounds of airborne 230Pu. Pu body burden at the time of cytogenetic study varied from values close to the method sensitivity to values multiply exceeding the permissible level. Standard (routine) methods of peripheral blood lymphocytes cultivation were applied. Chromatid- and chromosomal-type structural changes were estimated. Aberrations were estimated per 100 examined metaphase cells. The quantitative relationship between the CA frequency and Pu body burden and the absorbed dose to the lung was found. Mathematical processing of results was carried out based on the phenomenological model. The results were shown as theoretical and experimental curves. The threshold of the CA yield was 0.43 +/- 0.03 kBq (Pu body burden) and 6.12 +/- 1.20 cGy (absorbed dose to the lung).

  13. [ECG indices in dogs after inhalation of 239Pu].

    PubMed

    Karpova, V N

    1985-11-01

    Dogs of both sexes aged 2 to 4 were subjected to inhalation inoculation with polymer 239Pu or submicron 239PuO2 aerosols in amounts close to acute, subacute and chronically effective ones. ECG was recorded in standard, amplified and single leads (V3). All calculations were done by lead II. Signs of the right heart overburdening were noted in the presence of the P-pulmonale complex, deep S1 wave or cardiac electrical axis of SI-SII-SIII type. Signs of the right heart overburdening were revealed after inhalation of polimer 239Pu (70%). The absence of similar changes in damage caused by 239Pu could be attributed to its fast resorption from the lungs resulting in more moderate lesion of the respiratory organs.

  14. Radiation damage effects in candidate titanates for Pu disposition: Pyrochlore

    NASA Astrophysics Data System (ADS)

    Strachan, D. M.; Scheele, R. D.; Buck, E. C.; Icenhower, J. P.; Kozelisky, A. E.; Sell, R. L.; Elovich, R. J.; Buchmiller, W. C.

    2005-10-01

    Laboratory experiments on titanate ceramics were performed to verify whether certain assumptions are valid regarding the swelling, chemical durability, and microcracking that might occur as 239Pu decays. Titanate ceramics are the material of choice for the immobilization of surplus weapons-grade Pu. The short-lived isotope 238Pu, was incorporated into the ceramic formulation to accelerate the effects of radiation-induced damage. We report on the effects of this damage on the density (volumetric swelling <6%), crystal structure of pyrochlore-bearing specimens (amorphous after about 2 × 1018 α/g), and dissolution (no change from the fully crystalline specimen). Even though the specimens became amorphous during the tests, there was no evidence for microcracking in the photomicrographs from the scanning electron microscope. Thus, although pyrochlore is susceptible to radiation-induced damage, the material remains chemically and physically viable as a material for immobilizing surplus weapons-grade Pu.

  15. Ferro- and antiferro-magnetism in (Np, Pu)BC

    SciTech Connect

    Klimczuk, T.; Kozub, A. L.; Griveau, J.-C.; Colineau, E.; Wastin, F.; Falmbigl, M.; Rogl, P.

    2015-04-01

    Two new transuranium metal boron carbides, NpBC and PuBC, have been synthesized. Rietveld refinements of powder XRD patterns of (Np,Pu)BC confirmed in both cases isotypism with the structure type of UBC. Temperature dependent magnetic susceptibility data reveal antiferromagnetic ordering for PuBC below T{sub N} = 44 K, whereas ferromagnetic ordering was found for NpBC below T{sub C} = 61 K. Heat capacity measurements prove the bulk character of the observed magnetic transition for both compounds. The total energy electronic band structure calculations support formation of the ferromagnetic ground state for NpBC and the antiferromagnetic ground state for PuBC.

  16. Spatial and temporal distribution of Pu in the Northwest Pacific Ocean using modern coral archives.

    PubMed

    Lindahl, Patric; Andersen, Morten B; Keith-Roach, Miranda; Worsfold, Paul; Hyeong, Kiseong; Choi, Min-Seok; Lee, Sang-Hoon

    2012-04-01

    Historical (239)Pu activity concentrations and (240)Pu/(239)Pu atom ratios were determined in skeletons of dated modern corals collected from three locations (Chuuk Lagoon, Ishigaki Island and Iki Island) to identify spatial and temporal variations in Pu inputs to the Northwest Pacific Ocean. The main Pu source in the Northwest Pacific is fallout from atmospheric nuclear weapons testing which consists of global fallout and close-in fallout from the former US Pacific Proving Grounds (PPG) in the Marshall Islands. PPG close-in fallout dominated the Pu input in the 1950s, as was observed with higher (240)Pu/(239)Pu atom ratios (>0.30) at the Ishigaki site. Specific fallout Pu contamination from the Nagasaki atomic bomb and the Ivy Mike thermonuclear detonation at the PPG were identified at Ishigaki Island from the (240)Pu/(239)Pu atom ratios of 0.07 and 0.46, respectively. During the 1960s and 1970s, global fallout was the major Pu source to the Northwest Pacific with over 60% contribution to the total Pu. After the cessation of the atmospheric nuclear tests, the PPG again dominated the Pu input due to the continuous transport of remobilised Pu from the Marshall Islands along the North Equatorial Current and the subsequent Kuroshio Current. The Pu contributions from the PPG in recent coral bands (1984 onwards) varied over time with average estimated PPG contributions between 54% and 72% depending on location.

  17. Method of removing Pu(IV) polymer from nuclear fuel reclaiming liquid

    DOEpatents

    Tallent, Othar K.; Mailen, James C.; Bell, Jimmy T.; Arwood, Phillip C.

    1982-01-01

    A Pu(IV) polymer not extractable from a nuclear fuel reclaiming solution by conventional processes is electrolytically converted to Pu.sup.3+ and PuO.sub.2.sup.2+ ions which are subsequently converted to Pu.sup.4+ ions extractable by the conventional processes.

  18. Spatial and temporal distribution of Pu in the Northwest Pacific Ocean using modern coral archives.

    PubMed

    Lindahl, Patric; Andersen, Morten B; Keith-Roach, Miranda; Worsfold, Paul; Hyeong, Kiseong; Choi, Min-Seok; Lee, Sang-Hoon

    2012-04-01

    Historical (239)Pu activity concentrations and (240)Pu/(239)Pu atom ratios were determined in skeletons of dated modern corals collected from three locations (Chuuk Lagoon, Ishigaki Island and Iki Island) to identify spatial and temporal variations in Pu inputs to the Northwest Pacific Ocean. The main Pu source in the Northwest Pacific is fallout from atmospheric nuclear weapons testing which consists of global fallout and close-in fallout from the former US Pacific Proving Grounds (PPG) in the Marshall Islands. PPG close-in fallout dominated the Pu input in the 1950s, as was observed with higher (240)Pu/(239)Pu atom ratios (>0.30) at the Ishigaki site. Specific fallout Pu contamination from the Nagasaki atomic bomb and the Ivy Mike thermonuclear detonation at the PPG were identified at Ishigaki Island from the (240)Pu/(239)Pu atom ratios of 0.07 and 0.46, respectively. During the 1960s and 1970s, global fallout was the major Pu source to the Northwest Pacific with over 60% contribution to the total Pu. After the cessation of the atmospheric nuclear tests, the PPG again dominated the Pu input due to the continuous transport of remobilised Pu from the Marshall Islands along the North Equatorial Current and the subsequent Kuroshio Current. The Pu contributions from the PPG in recent coral bands (1984 onwards) varied over time with average estimated PPG contributions between 54% and 72% depending on location. PMID:21890207

  19. Probing Actinide Electronic Structure through Pu Cluster Calculations

    DOE PAGES

    Ryzhkov, Mickhail V.; Mirmelstein, Alexei; Yu, Sung-Woo; Chung, Brandon W.; Tobin, James G.

    2013-02-26

    The calculations for the electronic structure of clusters of plutonium have been performed, within the framework of the relativistic discrete-variational method. Moreover, these theoretical results and those calculated earlier for related systems have been compared to spectroscopic data produced in the experimental investigations of bulk systems, including photoelectron spectroscopy. Observation of the changes in the Pu electronic structure as a function of size provides powerful insight for aspects of bulk Pu electronic structure.

  20. First principles calculations on Ga stabilized δ-Pu alloys

    NASA Astrophysics Data System (ADS)

    Hernandez, Sarah C.; Schwartz, Daniel S.; Taylor, Christopher D.; Ray, Asok K.

    2014-03-01

    The high temperature face-centered-cubic phase (δ) of plutonium (Pu) may be stabilized at room temperature with the inclusion of impurities, such as gallium (Ga) or aluminum. The addition of Ga within the δ-phase influences the structural and electronic properties of Pu. Using the full-potential linearized augmented plane-wave density functional theory based method we present a systematic study of bulk Pu-Ga alloys. The goals of these calculations are to understand the evolution of the structural and electronic properties of Ga in a δ-Pu lattice. A 32-atom δ-Pu supercell was used to study Pu-Ga alloys at 3.125, 6.25, and 9.375 at. % Ga concentrations. We observe that regardless of the Ga concentration, the magnetic ground state predicted was anti-ferromagnetic, which is contrary to experimental results. However, the equilibrium lattice constants decrease with increasing Ga concentration, which is in agreement with experimental observations. Furthermore, when more than one Ga impurity is present within the supercell, the Ga atoms prefer to be at third nearest neighbor distance. The local effects of the bond lengths around the Ga atom, formation energies and partial density of states (PDOS) in the lowest energy structures will be discussed in detail. PDOS illustrates a Pu 6d and Ga 4p hybridization. Finally, we will also discuss the effects of a hydrogen-vacancy complex within a bulk Pu-Ga alloy. This work has been supported by the US Department of Energy through the Los Alamos National Laboratory LDRD Program.

  1. Method for producing H.sub.2 using a rotating drum reactor with a pulse jet heat source

    DOEpatents

    Paulson, Leland E.

    1990-01-01

    A method of producing hydrogen by an endothermic steam-carbon reaction using a rotating drum reactor and a pulse jet combustor. The pulse jet combustor uses coal dust as a fuel to provide reaction temperatures of 1300.degree. to 1400.degree. F. Low-rank coal, water, limestone and catalyst are fed into the drum reactor where they are heated, tumbled and reacted. Part of the reaction product from the rotating drum reactor is hydrogen which can be utilized in suitable devices.

  2. Unusual behaviour of (Np,Pu)B2C

    NASA Astrophysics Data System (ADS)

    Klimczuk, Tomasz; Boulet, Pascal; Griveau, Jean-Christophe; Colineau, Eric; Bauer, Ernst; Falmbigl, Matthias; Rogl, Peter; Wastin, Franck

    2015-02-01

    Two transuranium metal boron carbides, NpB2C and PuB2C have been synthesized by argon arc melting. The crystal structures of the {Np,Pu}B2C compounds were determined from single-crystal X-ray data to be isotypic with the ThB2C-type (space group ?, a = 0.6532(2) nm; c = 1.0769(3) nm for NpB2C and a = 0.6509(2) nm; c = 1.0818(3) nm for PuB2C; Z = 9). Physical properties have been derived from polycrystalline bulk material in the temperature range from 2 to 300 K and in magnetic fields up to 9 T. Magnetic susceptibility and heat capacity data indicate the occurrence of antiferromagnetic ordering for NpB2C with a Neel temperature TN = 68 K. PuB2C is a Pauli paramagnet most likely due to a strong hybridization of s(p,d) electrons with the Pu-5f states. A pseudo-gap, as concluded from the Sommerfeld value and the electronic transport, is thought to be a consequence of the hybridization. The magnetic behaviour of {Np,Pu}B2C is consistent with the criterion of Hill.

  3. /sup 238/Pu processing at the Savannah River Plant

    SciTech Connect

    Burney, G.A.

    1983-01-01

    /sup 238/Pu is produced by irradiating /sup 237/Np. The /sup 237/Np is produced as a byproduct when natural or enriched uranium is irradiated with neutrons. The /sup 237/Np is separated by solvent extraction and ion exchange. It is converted to NpO/sub 2/ and fabricated into targets for irradiation. The irradiated targets are cooled and dissolved in strong nitric acid. The /sup 238/Pu and /sup 237/Np are separated from fission products and other cationic impurities and from each other by three cycles of anion exchange. The /sup 237/Np is recycled to produce more targets for irradiation. The pure /sup 238/Pu solution is precipitated as Pu oxalate and calcined to PuO/sub 2/. After several powder-conditioning steps, the PuO/sub 2/ is hot pressed into fuel forms. Each form is encased in iridium for loading into a specially designed power unit for space application. 8 references, 9 figures, 1 table.

  4. Utilizing Drumming for American Indians/Alaska Natives with Substance Use Disorders: A Focus Group Study

    PubMed Central

    Dickerson, Daniel; Robichaud, Francis; Teruya, Cheryl; Nagaran, Kathleen; Hser, Yih-Ing

    2013-01-01

    Background Drumming has been utilized among American Indian/Alaska Native (AI/AN) tribes for centuries to promote healing and self-expression. Drum-Assisted Recovery Therapy for Native Americans (DARTNA), currently under development, is a substance abuse treatment utilizing drumming as a core component. Objectives Focus groups were conducted to assist in the development of the DARTNA protocol. Feedback obtained from these focus groups will inform a subsequent pretest of DARTNA and an empirical study analyzing its effectiveness. Methods Three focus groups were conducted among AIs/ANs with substance use disorders (n = 6), substance abuse treatment providers (n = 8), and a community advisory board (n = 4) to solicit feedback prior to a pretest of the DARTNA protocol. Results Overall, participants indicated that DARTNA could be beneficial for AIs/ANs with substance use disorders. Four overarching conceptual themes emerged across the focus groups: (1) benefits of drumming, (2) importance of a culture-based focus, (3) addressing gender roles in drumming activities, and (4) providing a foundation of common AI/AN traditions. Conclusions The DARTNA protocol is a potentially beneficial and culturally appropriate substance abuse treatment strategy for AIs/ANs. In order to optimize the potential benefits of a substance abuse treatment protocol utilizing drumming for AIs/ANs, adequate attention to tribal diversity and gender roles is needed. Scientific Significance Due to the shortage of substance abuse treatments utilizing traditional healing activities for AIs/ANs, including drumming, results from this study provide an opportunity to develop an intervention that may meet the unique treatment needs of AIs/ANs. PMID:22931086

  5. Study of neutron-deficient isotopes of Fl in the 239Pu, 240Pu + 48Ca reactions

    NASA Astrophysics Data System (ADS)

    Voinov, A. A.; Utyonkov, V. K.; Brewer, N. T.; Oganessian, Yu Ts; Rykaczewski, K. P.; Abdullin, F. Sh; Dmitriev, S. N.; Grzywacz, R. K.; Itkis, M. G.; Miernik, K.; Polyakov, A. N.; Roberto, J. B.; Sagaidak, R. N.; Shirokovsky, I. V.; Shumeiko, M. V.; Tsyganov, Yu S.; Subbotin, V. G.; Sukhov, A. M.; Sabelnikov, A. V.; Vostokin, G. K.; Hamilton, J. H.; Stoyer, M. A.; Strauss, S. Y.

    2016-07-01

    The results of the experiments aimed at the synthesis of Fl isotopes in the 239Pu + 48Ca and 240Pu + 48Ca reactions are presented. The experiment was performed using the Dubna gas-filled recoil separator at the U400 cyclotron. In the 239Pu+48Ca experiment one decay of spontaneously fissioning 284Fl was detected at 245-MeV beam energy. In the 240Pu+48Ca experiment three decay chains of 285Fl were detected at 245 MeV and four decays were assigned to 284Fl at the higher 48Ca beam energy of 250 MeV. The α-decay energy of 285Fl was measured for the first time and decay properties of its descendants 281Cn, 277Ds, 273Hs, 269Sg, and 265Rf were determined more precisely. The cross section of the 239Pu(48Ca,3n)284Fl reaction was observed to be about 20 times lower than those predicted by theoretical models and 50 times less than the value measured in the 244Pu+48Ca reaction. The cross sections of the 240Pu(48Ca,4-3n)284,285Fl at both 48Ca energies are similar and exceed that observed in the reaction with lighter isotope 239Pu by a factor of 10. The decay properties of the synthesized nuclei and their production cross sections indicate rapid decrease of stability of superheavy nuclei with departing from the neutron number N=184 predicted to be the next magic number.

  6. Ab initio equation-of-state and elastic properties of Pu metal and Pu-Ga alloys

    NASA Astrophysics Data System (ADS)

    Per, Soderlind; Landa, Alex

    2010-03-01

    We present results of ab initio calculations of equation-of-state and elastic properties for Pu metal and Pu-Ga alloys. For this we have employed density-functional theory (DFT) in conjunction with spin-orbit coupling and orbital polarization for the metal and coherent-potential approximation (CPA) for the alloys. All Pu systems benefit from spin polarization which is consistent with previous DFT studies of plutonium. We show that orbital correlations become more important proceeding from α->β->γ plutonium, thus suggesting increasing f-electron correlation (localization). For δ-Pu- Ga alloys we find that the system softens with larger Ga content, i.e., bulk modulus, elastic constants, and chemical bonding weakens with increasing Ga concentration. This inverse relationship is nearly linear and supported by measurements on polycrystal δ-Pu-Ga alloys. For Pu metal, our single-crystal results also relates reasonably with ultrasound data on polycrystal samples where available. The comparison is indirect but made possible by approximating the polycrystal with an isotropic (uniform strain) single crystal. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

  7. On the electrochemical formation of Pu-Al alloys in molten LiCl-KCl

    NASA Astrophysics Data System (ADS)

    Mendes, E.; Malmbeck, R.; Nourry, C.; Souček, P.; Glatz, J.-P.

    2012-01-01

    Properties of Pu-Al alloys were investigated in connection with development of pyrochemical methods for reprocessing of spent nuclear fuel. Electroseparation techniques in molten LiCl-KCl are being developed in ITU to group-selectively recover actinides from the mixture with fission products. In the process, actinides are electrochemically reduced on solid aluminium cathodes, forming solid actinide-aluminium alloys. This article is focused on electro-chemical characterisation of Pu-Al alloys in molten LiCl-KCl, on electrodeposition of Pu on solid Al electrodes and on determination of chemical composition and structure of the formed alloys. Cyclic voltammetry and chronopotentiometry were used to study Pu-Al alloys in the temperature range 400-550 °C. Pu is reduced to metal in one reduction step Pu 3+/Pu 0 on an inert W electrode. On a reactive Al electrode, the reduction of Pu 3+ to Pu 0 occurs at a more positive potential due to formation of Pu-Al alloys. The open circuit potential technique was used to identify the alloys formed. Stable deposits were obtained by potentiostatic electrolyses of LiCl-KCl-PuCl 3 melts on Al plates. XRD and SEM-EDX analyses were used to characterise the alloys, which were composed mainly of PuAl 4 with some PuAl 3. In addition, the preparation of PuCl 3 containing salt by carbochlorination of PuO 2 is described.

  8. Indonesian commercial bus drum brake system temperature model

    NASA Astrophysics Data System (ADS)

    Wibowo, D. B.; Haryanto, I.; Laksono, N. P.

    2016-03-01

    Brake system is the most significant aspect of an automobile safety. It must be able to slow the vehicle, quickly intervening and reliable under varying conditions. Commercial bus in Indonesia, which often stops suddenly and has a high initial velocity, will raise the temperature of braking significantly. From the thermal analysis it is observed that for the bus with the vehicle laden mass of 15 tons and initial velocity of 80 km/h the temperature is increasing with time and reaches the highest temperature of 270.1 °C when stops on a flat road and reaches 311.2 °C on a declination road angle, ø, 20°. These temperatures exceeded evaporation temperature of brake oil DOT 3 and DOT 4. Besides that, the magnitude of the braking temperature also potentially lowers the friction coefficient of more than 30%. The brakes are pressed repeatedly and high-g decelerations also causes brake lining wear out quickly and must be replaced every 1 month as well as the emergence of a large thermal stress which can lead to thermal cracking or thermal fatigue crack. Brake fade phenomenon that could be the cause of many buses accident in Indonesia because of the failure of the braking function. The chances of accidents will be even greater when the brake is worn and not immediately replaced which could cause hot spots as rivets attached to the brake drum and brake oil is not changed for more than 2 years that could potentially lower the evaporation temperature because of the effect hygroscopic.

  9. A photometric analysis of tablet movement in a side-vented perforated drum (Accela-Cota).

    PubMed

    Leaver, T M; Shannon, H D; Rowe, R C

    1985-01-01

    A novel particle tracing technique has been used to study the effect of the normal process variables i.e. drum speed, drum loading and the presence/absence of mixing elements (baffles) on the movement of tablets in a side-vented perforated drum (24 in diameter Accela-Cota). The technique involves measuring the duration of light emission from a single luminous tablet using a photomultiplier mounted to scan the same area as a spray gun, and has enabled the quantification of both the time that the tablet spends on the surface per pass (surface time) and the time that the tablet spends within the bulk of the tablet bed (circulation time) over run lengths equating to the normal tablet coating cycle. The technique also allows the study of the uniformity of tablet appearances by means of circulation profiles. It was found that, while both the surface and circulation times decreased with increasing drum speed and loading, there was irregularity of tablet appearance especially at low drum speeds and in the absence of baffles.

  10. Discrete particle simulations predicting mixing behavior of solid substrate particles in a rotating drum fermenter.

    PubMed

    Schutyser, M A; Padding, J T; Weber, F J; Briels, W J; Rinzema, A; Boom, R

    2001-12-20

    A soft-sphere discrete particle model was used to simulate mixing behavior of solid substrate particles in a slow rotating drum for solid-state fermentation. In this approach, forces acting on and subsequent motion of individual particles can be predicted. The (2D) simulations were qualitatively and quantitatively validated by mixing experiments using video and image analysis techniques. It was found that the simulations successfully predicted the mixing progress as a function of the degree of filling and size of the drum. It is shown that only relatively large, straight baffles perpendicular to the drum wall (67% of the drum radius) increase the mixing performance of the rotating drum. Considering the different aspects of mixing dealt with in this work, it is concluded that the soft sphere discrete particle model can serve as a valuable tool for investigating mixing of solid substrate particles. Finally, it is expected that this model may evolve into a potential tool for design and scale-up of mixed solid-state fermenters. PMID:11745144

  11. The hybrid energy spectrum of Telescope Array's Middle Drum Detector and surface array

    NASA Astrophysics Data System (ADS)

    Abbasi, R. U.; Abe, M.; Abu-Zayyad, T.; Allen, M. G.; Anderson, R.; Azuma, R.; Barcikowski, E.; Belz, J. W.; Bergman, D. R.; Blake, S. A.; Cady, R.; Chae, M. J.; Cheon, B. G.; Chiba, J.; Chikawa, M.; Cho, W. R.; Fujii, T.; Fukushima, M.; Goto, T.; Hanlon, W.; Hayashi, Y.; Hayashida, N.; Hibino, K.; Honda, K.; Ikeda, D.; Inoue, N.; Ishii, T.; Ishimori, R.; Ito, H.; Ivanov, D.; Jui, C. C. H.; Kadota, K.; Kakimoto, F.; Kalashev, O.; Kasahara, K.; Kawai, H.; Kawakami, S.; Kawana, S.; Kawata, K.; Kido, E.; Kim, H. B.; Kim, J. H.; Kim, J. H.; Kitamura, S.; Kitamura, Y.; Kuzmin, V.; Kwon, Y. J.; Lan, J.; Lim, S. I.; Lundquist, J. P.; Machida, K.; Martens, K.; Matsuda, T.; Matsuyama, T.; Matthews, J. N.; Minamino, M.; Mukai, K.; Myers, I.; Nagasawa, K.; Nagataki, S.; Nakamura, T.; Nonaka, T.; Nozato, A.; Ogio, S.; Ogura, J.; Ohnishi, M.; Ohoka, H.; Oki, K.; Okuda, T.; Ono, M.; Oshima, A.; Ozawa, S.; Park, I. H.; Pshirkov, M. S.; Rodriguez, D. C.; Rubtsov, G.; Ryu, D.; Sagawa, H.; Sakurai, N.; Sampson, A. L.; Scott, L. M.; Shah, P. D.; Shibata, F.; Shibata, T.; Shimodaira, H.; Shin, B. K.; Shin, H. S.; Smith, J. D.; Sokolsky, P.; Springer, R. W.; Stokes, B. T.; Stratton, S. R.; Stroman, T. A.; Suzawa, T.; Takamura, M.; Takeda, M.; Takeishi, R.; Taketa, A.; Takita, M.; Tameda, Y.; Tanaka, H.; Tanaka, K.; Tanaka, M.; Thomas, S. B.; Thomson, G. B.; Tinyakov, P.; Tkachev, I.; Tokuno, H.; Tomida, T.; Troitsky, S.; Tsunesada, Y.; Tsutsumi, K.; Uchihori, Y.; Udo, S.; Urban, F.; Vasiloff, G.; Wong, T.; Yamane, R.; Yamaoka, H.; Yamazaki, K.; Yang, J.; Yashiro, K.; Yoneda, Y.; Yoshida, S.; Yoshii, H.; Zollinger, R.; Zundel, Z.

    2015-08-01

    The Telescope Array experiment studies ultra high energy cosmic rays using a hybrid detector. Fluorescence telescopes measure the longitudinal development of the extensive air shower generated when a primary cosmic ray particle interacts with the atmosphere. Meanwhile, scintillator detectors measure the lateral distribution of secondary shower particles that hit the ground. The Middle Drum (MD) fluorescence telescope station consists of 14 telescopes from the High Resolution Fly's Eye (HiRes) experiment, providing a direct link back to the HiRes measurements. Using the scintillator detector data in conjunction with the telescope data improves the geometrical reconstruction of the showers significantly, and hence, provides a more accurate reconstruction of the energy of the primary particle. The Middle Drum hybrid spectrum is presented and compared to that measured by the Middle Drum station in monocular mode. Further, the hybrid data establishes a link between the Middle Drum data and the surface array. A comparison between the Middle Drum hybrid energy spectrum and scintillator Surface Detector (SD) spectrum is also shown.

  12. Numerical Studies on Time-Varying Stiffness of Disk-Drum Type Rotor with Bolt Loosening

    NASA Astrophysics Data System (ADS)

    Qin, Zhaoye; Chu, Fulei

    2015-07-01

    Disk-drum type rotors are widely used in industry for their high stiffness and low weight properties. In disk-drum type rotors, the adjacent disks and drums are commonly connected by bolted joints. Those rotating joint interfaces are subjected to numerous combinations of loads during normal operation, where loosening of the connecting bolts might occur. The bolt loosening will change the local stiffness of the rotor, which in turn affect the rotor dynamics and even result in structural failures. In this paper, the local stiffness of a disk- drum rotor with bolt loosening is investigated numerically. A three-dimensional (3D) finite element (FE) model for the bolted disk-drum joint is established in ANSYS, where the bolt loosening is simulated by reducing the preloads of certain bolts, and removing those bolts as the limiting case. Simulations are performed on the FE model to evaluate the joint behaviour under static loads. Periodic variations of the joint deflections with respect to the rotation angle of the shaft are obtained, which implies the appearance of the time-varying local stiffness in the rotor system. The studies in this paper help accurate prediction of the rotor dynamics and early detection of bolt loosening.

  13. Hazards Associated with Legacy Nitrate Salt Waste Drums Managed under the Container Isolation Plan

    SciTech Connect

    Funk, David John; Clark, David Lewis

    2015-01-07

    At present, there are 29 drums of nitrate waste salts (oxidizers with potentially acidic liquid bearing RCRA characteristics D001 and D002) that are awaiting processing, specifically to eliminate these characteristics and to allow for ultimate disposition at WIPP. As a result of the Feb. 14th, 2014 drum breach at WIPP, and the subsequent identification of the breached drum as a product ofLANL TRU waste disposition on May 15th, 2014, these 29 containers were moved into the Perrnacon in Dome 231 at TA-54 Area G, as part of the New Mexico Environment Department (NMED) approved container isolation plan. The plan is designed to mitigate hazards associated with the nitrate salt bearing waste stream. The purpose of this document is to articulate the hazards associated with un-remediated nitrate salts while in storage at LANL. These hazards are distinctly different from the Swheat-remediated nitrate salt bearing drums, and this document is intended to support the request to remove the un-remediated drums from management under the container isolation plan. Plans to remediate and/or treat both of these waste types are being developed separately, and are beyond the scope of this document.

  14. A study of accelerated radiation damage effects in PuO2 and gadolinia-stabilized cubic zirconia, Zr0.79Gd0.14Pu0.07O1.93, doped with 238Pu

    NASA Astrophysics Data System (ADS)

    Burakov, B. E.; Yagovkina, M. A.

    2015-12-01

    Polycrystalline samples of cubic zirconia, Zr0.79Gd0.14Pu0.07O1.93, doped with approximately 9.9 wt.% 238Pu, and PuO2 containing 11.0 wt. % 238Pu (and main isotope is 239Pu) have been repeatedly studied during many years by X-ray diffraction analysis. At a temperature of 25 °C the unit-cell parameter of PuO2 increases depending on accumulated dose, and is accompanied by decrease of coherent scattering region (CSR). Self-irradiation of Zr0.79Gd0.14Pu0.07O1.93 is accompanied with repeated change of unit-cell parameter and CSR.

  15. Pu and 137Cs in the Yangtze River estuary sediments: distribution and source identification.

    PubMed

    Liu, Zhiyong; Zheng, Jian; Pan, Shaoming; Dong, Wei; Yamada, Masatoshi; Aono, Tatsuo; Guo, Qiuju

    2011-03-01

    Pu isotopes and (137)Cs were analyzed using sector field ICP-MS and γ spectrometry, respectively, in surface sediment and core sediment samples from the Yangtze River estuary. (239+240)Pu activity and (240)Pu/(239)Pu atom ratios (>0.18) shows a generally increasing trend from land to sea and from north to south in the estuary. This spatial distribution pattern indicates that the Pacific Proving Grounds (PPG) source Pu transported by ocean currents was intensively scavenged into the suspended sediment under favorable conditions, and mixed with riverine sediment as the water circulated in the estuary. This process is the main control for the distribution of Pu in the estuary. Moreover, Pu is also an important indicator for monitoring the changes of environmental radioactivity in the estuary as the river basin is currently the site of extensive human activities and the sea level is rising because of global climate changes. For core sediment samples the maximum peak of (239+240)Pu activity was observed at a depth of 172 cm. The sedimentation rate was estimated on the basis of the Pu maximum deposition peak in 1963-1964 to be 4.1 cm/a. The contributions of the PPG close-in fallout Pu (44%) and the riverine Pu (45%) in Yangtze River estuary sediments are equally important for the total Pu deposition in the estuary, which challenges the current hypothesis that the riverine Pu input was the major source of Pu budget in this area.

  16. Neutron Capture Cross Section Measurement on $^{238}$Pu at DANCE

    SciTech Connect

    Chyzh, A; Wu, C Y

    2011-02-14

    The proposed neutron capture measurement for {sup 238}Pu was carried out in Nov-Dec, 2010, using the DANCE array at LANSCE, LANL. The total beam-on-target time is about 14 days plus additional 5 days for the background measurement. The target was prepared at LLNL with the new electrplating cell capable of plating the {sup 238}Pu isotope simultaneously on both sides of the 3-{micro}m thick Ti backing foil. A total mass of 395 {micro}g with an activity of 6.8 mCi was deposited onto the area of 7 mm in diameter. The {sup 238}Pu sample was enriched to 99.35%. The target was covered by 1.4 {micro}m double-side aluminized mylar and then inserted into a specially designed vacuum-tight container, shown in Fig. 1, for the {sup 238}Pu containment. The container was tested for leaks in the vacuum chamber at LLNL. An identical container without {sup 238}Pu was made as well and used as a blank for the background measurement.

  17. Measurements Conducted on an Unknown Object Labeled Pu-239

    SciTech Connect

    Hoteling, Nathan

    2013-11-18

    Measurements were carried out on 12 November 2013 to determine whether Pu-239 was present on an object discovered in a plastic bag with label “Pu-­239 6 uCi.” Following initial survey measurements to verify that the object was not leaking or contaminated, spectra were collected with a High Purity Germanium (HPGe) detector with object positioned in two different configurations. Analysis of the spectra did not yield any direct evidence of Pu-­239. From the measured spectra, minimum detectable activity (MDA) was determined to be approximately 2 uCi for the gamma-­ray measurements. Although there was no direct evidence of Pu-239, a peak at 60 keV characteristic of Am-­241 decay was observed. Since it is very likely that Am-­241 would be present in aged plutonium samples, this was interpreted as indirect evidence for the presence of plutonium on the object. Analysis of this peak led to an estimated Pu-­239 activity of 0.02–0.04 uCi, or <1x10-6 grams.

  18. The I-Pu-Xe age of the Moon

    NASA Technical Reports Server (NTRS)

    Swindle, T. D.; Caffee, M. W.; Hohenberg, C. M.

    1984-01-01

    The Rb-Sr analyses of some lunar samples which indicate that the Moon is close to the age of primitive meteorites are only reliable to within about 100 m.y. A potentially more precise chronometer is the I-Pu-Xe system. I129 has a 17 m.y. halflife and decays to Xe129; Pu244, with an 82 m.y. halflife, produces Xe131 to Xe136 in fission. The I129/Pu244 ratio has a halflife of 21 m.y. Xenon retention for the Earth could have begun as late as the event that gave birth to the Moon. For the Moon, it is hard to imagine that xenon retention could have begun before re-accretion of the fissioned (and initially dispersed?) material, particularly if that material got hot enough to account for the depletion of the volatile elements. Thus, if fission model are correct, xenon retention in the Earth certainly began no later than in the Moon, and possibly began earlier. Therefore, the I-Pu-Xe system is only marginally consistent with a fission origin. If further study confirms that the I/U ratio of the Moon is .01 or less, or if gas-rich lunar highland breccias with higher ratios of I129 to Pu244 are found, it would be difficult to explain the results in an earth-fission model of lunar origin.

  19. A rotating drum stimulator for scanning embossed patterns and textures across the skin.

    PubMed

    Johnson, K O; Phillips, J R

    1988-01-01

    A tactile stimulator is described that moves embossed or textured patterns tangentially across the skin. Patterns constructed by standard photoetching are mounted on the outer surface of a cylinder that rotates at a selected speed and is held in contact with the skin at a selected force. The stimulator operates in several modes to meet the different requirements of psychophysical and neurophysiological experiments. The features of note are (i) relatively small size and weight; (ii) flexible automated control of drum contact with the skin, angular velocity, axial position, and contact force; (iii) monitoring of drum angular and axial location to better than 10 micron accuracy; (iv) construction with commercially available devices; (v) electronic monitoring of skin contact; and (vi) rapid drum changes (2 seconds) during psychophysical or neurophysiological experiments. PMID:3361948

  20. Measurement of VOC permeability of polymer bags and VOC solubility in polyethylene drum liner

    SciTech Connect

    Liekhus, K.J.; Peterson, E.S.

    1995-03-01

    A test program conducted at the Idaho National Engineering Laboratory (INEL) investigated the use of a transport model to estimate the volatile organic compound (VOC) concentration in the void volume of a waste drum. Unsteady-state VOC transport model equations account for VOC permeation of polymer bags, VOC diffusion across openings in layers of confinement, and VOC solubility in a polyethylene drum liner. In support of this program, the VOC permeability of polymer bags and VOC equilibrium concentration in a polyethylene drum liner were measured for nine VOCs. The VOCs used in experiments were dichloromethane, carbon tetrachloride, cyclohexane, toluene, 1,1,1-trichloroethane, methanol, 1,1,2-trichloro-1,2,2-trifluoroethane (Freon-113), trichloroethylene, and p-xylene. The experimental results of these measurements as well as a method of estimating both parameters in the absence of experimental data are described in this report.

  1. Ringlike spin segregation of binary mixtures in a high-velocity rotating drum

    NASA Astrophysics Data System (ADS)

    Decai, Huang; Ming, Lu; Gang, Sun; Yaodong, Feng; Min, Sun; Haiping, Wu; Kaiming, Deng

    2012-03-01

    This study presents molecular dynamics simulations on the segregation of binary mixtures in a high-velocity rotating drum. Depending on the ratio between the particle radius and density, similarities to the Brazil-nut effect and its reverse form are shown in the ringlike spin segregation patterns in radial direction. The smaller and heavier particles accumulated toward the drum wall, whereas the bigger and lighter particles accumulated toward the drum center. The effects of particle radius and density on the segregation states were quantified and the phase diagram of segregation in the ρb/ρs - rb/rs space was plotted. The observed phenomena can be explained by the combined percolation and the buoyancy effects.

  2. Pu(V) transport through Savannah River Site soils - an evaluation of a conceptual model of surface- mediated reduction to Pu (IV).

    PubMed

    Powell, Brian A; Kaplan, Daniel I; Serkiz, Steven M; Coates, John T; Fjeld, Robert A

    2014-05-01

    Over the last fifteen years the Savannah River Site (SRS) in South Carolina, USA, was selected as the site of three new plutonium facilities: the Mixed Oxide Fuel Fabrication Facility, Pit Disassembly and Conversion Facility, and the Pu Immobilization Plant. In order to assess the potential human and environmental risk associated with these recent initiatives, improved understanding of the fate and transport of Pu in the SRS subsurface environment is necessary. The hypothesis of this study was that the more mobile forms of Pu, Pu(V) and Pu(VI), would be reduced to the less mobile Pu(III/IV) oxidation states under ambient SRS subsurface conditions. Laboratory-scale dynamic flow experiments (i.e., column studies) indicated that Pu(V) was very mobile in SRS sediments. At higher pH values the mobility of Pu decreased and the fraction of Pu that became irreversibly sorbed to the sediment increased, albeit, only slightly. Conversely, these column experiments showed that Pu(IV) was essentially immobile and was largely irreversibly sorbed to the sediment. More than 100 batch sorption experiments were also conducted with four end-member sediments, i.e., sediments that include the chemical, textural, and mineralogical properties likely to exist in the SRS. These tests were conducted as a function of initial Pu oxidation state, pH, and contact time and consistently demonstrated that although Pu(V) sorbed initially quite weakly to sediments, it slowly, over the course of <33 days, sorbed very strongly to sediments, to approximately the same degree as Pu(IV). This is consistent with our hypothesis that Pu(V) is reduced to the more strongly sorbing form of Pu, Pu(IV). These studies provide important experimental support for a conceptual geochemical model for dissolved Pu in a highly weathered subsurface environment. That is that, irrespective of the initial oxidation state of the dissolved Pu introduced into a SRS sediment system, Pu(IV) controls the environmental transport

  3. LA-ICP-MS for Pu source identification at Mayak PA, the Urals, Russia.

    PubMed

    Cagno, S; Hellemans, K; Lind, O C; Skipperud, L; Janssens, K; Salbu, B

    2014-02-01

    Information on Pu in environmental samples is traditionally based on the determination of the (240+239)Pu activity via Alpha Spectrometry (AS). A large number of alpha spectrometry sources (planchettes) containing radiochemically separated Pu are therefore stored worldwide and are available for further analyses. These archive samples represent a resource from which valuable information on isotopic composition of alpha emitters including Pu can be obtained. The relative abundances of Pu isotopes can be used to trace specific Pu sources and characterize the relative contributions of different Pu sources in a sample. Thus, in addition to the total (239+240)Pu activity, determination of the (240)Pu/(239)Pu ratio can provide valuable information on the nature of the Pu emitting sources. The Pu isotopic ratios can be determined by mass spectrometry techniques such as Sector Field Inductively Coupled Plasma Mass Spectrometry (SF-ICPMS) or Accelerator Mass Spectrometry (AMS) that require dissolution and complete destruction of the material deposited on the planchettes. In this study Laser Ablation (LA)-quadrupole-ICP-MS has been employed for the analysis of (239)Pu/(240)Pu ratios from alpha-planchettes prepared from samples originating from the Mayak PA nuclear facility, Russia. The results are compared with data from AMS and show that the (240)Pu/(239)Pu ratios obtained by LA-ICP-MS can be utilized to distinguish weapons-grade Pu from civil reprocessing sources. Moreover, isotope ratio mapping can also be performed across the planchettes, allowing e.g. the visualization of possible inhomogeneities in the Pu-isotope distribution on their surface. Thus, this solid sample technique can be applied to extract additional information from existing archives of samples. PMID:24424783

  4. Characterization of Pu concentration and its isotopic composition in a reference fallout material.

    PubMed

    Zhang, Yongsan; Zheng, Jian; Yamada, Masatoshi; Wu, Fengchang; Igarashi, Yasuhito; Hirose, Katsumi

    2010-02-01

    Because there is no reference material for fallout plutonium isotope monitoring, preparation of such a material is necessary for quality control of fallout radionuclides analysis for atmospheric environmental studies. In this work, we report the characterization of Pu activity and its isotopic composition in a reference fallout material prepared by the Meteorological Research Institute (MRI), Japan. This material was prepared from samples collected at 14 stations throughout Japan in 1963-1979, with reference values of (137)Cs, (90)Sr and (239)(+)(240)Pu activities. We analyzed the activities of (239)(+)(240)Pu and (241)Pu, and the atom ratios of (240)Pu/(239)Pu and (241)Pu/(239)Pu using an isotope dilution sector-field inductively coupled plasma mass spectrometry (SF-ICP-MS). The (239)(+)(240)Pu activities in this fallout material using acid leaching and total digestion were 6.56+/-0.20 mBq/g and 6.79+/-0.16 mBq/g, respectively. Atom ratios of (240)Pu/(239)Pu were 0.1915+/-0.0030 and 0.1922+/-0.0044, respectively. Both (240)Pu/(239)Pu and (241)Pu/(239)Pu atom ratios were slightly higher than those of global fallout, which could be attributed to the deposition of fallout radionuclides resulting from the Chinese nuclear weapons tests conducted in the 1970s. The dominant host phases of (239)(+)(240)Pu were found to be organic matter-sulfides (70%) with a relative high (240)Pu/(239)Pu atom ratio, and Fe-Mn oxides (19%) using a sequential extraction method.

  5. LA-ICP-MS for Pu source identification at Mayak PA, the Urals, Russia.

    PubMed

    Cagno, S; Hellemans, K; Lind, O C; Skipperud, L; Janssens, K; Salbu, B

    2014-02-01

    Information on Pu in environmental samples is traditionally based on the determination of the (240+239)Pu activity via Alpha Spectrometry (AS). A large number of alpha spectrometry sources (planchettes) containing radiochemically separated Pu are therefore stored worldwide and are available for further analyses. These archive samples represent a resource from which valuable information on isotopic composition of alpha emitters including Pu can be obtained. The relative abundances of Pu isotopes can be used to trace specific Pu sources and characterize the relative contributions of different Pu sources in a sample. Thus, in addition to the total (239+240)Pu activity, determination of the (240)Pu/(239)Pu ratio can provide valuable information on the nature of the Pu emitting sources. The Pu isotopic ratios can be determined by mass spectrometry techniques such as Sector Field Inductively Coupled Plasma Mass Spectrometry (SF-ICPMS) or Accelerator Mass Spectrometry (AMS) that require dissolution and complete destruction of the material deposited on the planchettes. In this study Laser Ablation (LA)-quadrupole-ICP-MS has been employed for the analysis of (239)Pu/(240)Pu ratios from alpha-planchettes prepared from samples originating from the Mayak PA nuclear facility, Russia. The results are compared with data from AMS and show that the (240)Pu/(239)Pu ratios obtained by LA-ICP-MS can be utilized to distinguish weapons-grade Pu from civil reprocessing sources. Moreover, isotope ratio mapping can also be performed across the planchettes, allowing e.g. the visualization of possible inhomogeneities in the Pu-isotope distribution on their surface. Thus, this solid sample technique can be applied to extract additional information from existing archives of samples.

  6. Corrosion of steel drums containing cemented ion-exchange resins as intermediate level nuclear waste

    NASA Astrophysics Data System (ADS)

    Duffó, G. S.; Farina, S. B.; Schulz, F. M.

    2013-07-01

    Exhausted ion-exchange resins used in nuclear reactors are immobilized by cementation before being stored. They are contained in steel drums that may undergo internal corrosion depending on the presence of certain contaminants. The objective of this work is to evaluate the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins with different aggressive species. The corrosion potential and the corrosion rate of the steel, and the electrical resistivity of the matrix were monitored for 900 days. Results show that the cementation of ion-exchange resins seems not to pose special risks regarding the corrosion of the steel drums. The corrosion rate of the steel in contact with cemented ion-exchange resins in the absence of contaminants or in the presence of 2.3 wt.% sulphate content remains low (less than 0.1 μm/year) during the whole period of the study (900 days). The presence of chloride ions increases the corrosion rate of the steel at the beginning of the exposure but, after 1 year, the corrosion rate drops abruptly reaching a value close to 0.1 μm/year. This is probably due to the lack of water to sustain the corrosion process. When applying the results obtained in the present work to estimate the corrosion depth of the steel drums containing the cemented radioactive waste after a period of 300 years, it is found that in the most unfavourable case (high chloride contamination), the corrosion penetration will be considerably lower than the thickness of the wall of the steel drums. Cementation of ion-exchange resins does not seem to pose special risks regarding the corrosion of the steel drums that contained them; even in the case the matrix is highly contaminated with chloride ions.

  7. Reconstruction of the isotope activity content of heterogeneous nuclear waste drums.

    PubMed

    Krings, Thomas; Mauerhofer, Eric

    2012-07-01

    Radioactive waste must be characterized in order to verify its conformance with national regulations for intermediate storage or its disposal. Segmented gamma scanning (SGS) is a most widely applied non-destructive analytical technique for the characterization of radioactive waste drums. The isotope specific activity content is generally calculated assuming a homogeneous matrix and activity distribution for each measured drum segment. However, real radioactive waste drums exhibit non-uniform isotope and density distributions most affecting the reliability and accuracy of activities reconstruction in SGS. The presence of internal shielding structures in the waste drum contributes generally to a strong underestimation of the activity and this in particular for radioactive sources emitting low energy gamma-rays independently of their spatial distribution. In this work we present an improved method to quantify the activity of spatially concentrated gamma-emitting isotopes (point sources or hot spots) in heterogeneous waste drums with internal shielding structures. The isotope activity is reconstructed by numerical simulations and fits of the angular dependent count rate distribution recorded during the drum rotation in SGS using an analytical expression derived from a geometric model. First results of the improved method and enhancements of this method are shown and are compared to each other as well as to the conventional method which assumes a homogeneous matrix and activity distribution. It is shown that the new model improves the accuracy and the reliability of the activity reconstruction in SGS and that the presented algorithm is suitable with respect to the framework requirement of industrial application. PMID:22134026

  8. Results of the gamma-neutron mapper performance test on 55-gallon drums at the RWMC

    SciTech Connect

    Gehrke, R.J.; Lawrence, R.S.; Roybal, L.G.; Svoboda, J.M.; Harker, D.J.; Thompson, D.N.; Carpenter, M.V.; Josten, N.E.

    1995-07-01

    The primary purpose of the gamma-neutron mapper (G@) is to provide accurate and quantitative spatial information of the gamma-ray and neutron radiation fields as a function of position about the excavation of a radioactive waste site. The GNM is designed to operate remotely and can be delivered to any point on an excavation by the robotic gantry crane developed by the dig-face project at the Idaho National Engineering Laboratory (INEL). It can also be easily adapted to other delivery systems. The GNM can be deployed over a waste site at a predetermined scan rate and has sufficient accuracy to identify and quantify radioactive contaminants of importance. The results reported herein are from a performance test conducted at the Transuranic Storage Area, Building 628, of the Radioactive Waste Management Complex located at the INEL. This building is an active interim-storage area for 55-gal drums of transuranic waste from the Department of Energy`s Rocky Flats Plant. The performance test consisted of scanning a stack of drums five high by five wide. Prior to the test, radiation fields were measured by a health physicist at the center of the drums and ranged from 0.5 mR/h to 35 mR/h. Scans of the drums using the GNM were taken at standoff distances from the vertical drum stack of 15 cm, 30 cm, 45 cm, and 90 cm. Data were acquired at scan speeds of 7.5 cm/s and 15 cm/s. The results of these scans and a comparison of these results with the manifests of these drums are compared and discussed.

  9. Drumming as a Medium to Promote Emotional and Social Functioning of Children in Middle Childhood in Residential Care

    ERIC Educational Resources Information Center

    Flores, Kim; van Niekerk, Caroline; le Roux, Liana

    2016-01-01

    This study explores the potential of drumming to enhance emotional and social functioning of children in residential care. Fifteen children (aged 7-12) from a child and youth care centre in South Africa attended four months of weekly drumming sessions. Gestalt theory principles informed the workshops' theoretical foundation and interpretation of…

  10. 40 CFR 264.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... CFR parts 173, 178, and 179), if those regulations specify a particular inside container for the waste... container (49 CFR parts 178 and 179) of no more than 416-liter (110 gallon) capacity and surrounded by, at a... in 40 CFR 268.42(c)(1) may use fiber drums in place of metal outer containers. Such fiber drums...

  11. 7 CFR 160.201 - Fees generally for field inspection and certification of naval stores and drum containers of rosin.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... of naval stores and drum containers of rosin. 160.201 Section 160.201 Agriculture Regulations of the... Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) NAVAL STORES REGULATIONS AND STANDARDS FOR NAVAL STORES... of naval stores and drum containers of rosin. Except as provided in § 160.204, the following...

  12. 7 CFR 160.201 - Fees generally for field inspection and certification of naval stores and drum containers of rosin.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... of naval stores and drum containers of rosin. 160.201 Section 160.201 Agriculture Regulations of the... Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) NAVAL STORES REGULATIONS AND STANDARDS FOR NAVAL STORES... of naval stores and drum containers of rosin. Except as provided in § 160.204, the following...

  13. 40 CFR 264.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... in 40 CFR 268.42(c)(1) may use fiber drums in place of metal outer containers. Such fiber drums must... CFR parts 173, 178, and 179), if those regulations specify a particular inside container for the waste... container (49 CFR parts 178 and 179) of no more than 416-liter (110 gallon) capacity and surrounded by, at...

  14. 7 CFR 160.201 - Fees generally for field inspection and certification of naval stores and drum containers of rosin.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... of naval stores and drum containers of rosin. 160.201 Section 160.201 Agriculture Regulations of the... of naval stores and drum containers of rosin. Except as provided in § 160.204, the following fees shall be paid to the United States for the field inspection and certification of naval stores and...

  15. 7 CFR 160.201 - Fees generally for field inspection and certification of naval stores and drum containers of rosin.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... of naval stores and drum containers of rosin. 160.201 Section 160.201 Agriculture Regulations of the... of naval stores and drum containers of rosin. Except as provided in § 160.204, the following fees shall be paid to the United States for the field inspection and certification of naval stores and...

  16. 40 CFR 265.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... lab packs according to the requirements in 40 CFR 268.42(c)(1) may use fiber drums in place of metal outer containers. Such fiber drums must meet the DOT specifications in 49 CFR 173.12 and be overpacked... regulations (49 CFR parts 173, 178 and 179), if those regulations specify a particular inside container...

  17. 40 CFR 265.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... lab packs according to the requirements in 40 CFR 268.42(c)(1) may use fiber drums in place of metal outer containers. Such fiber drums must meet the DOT specifications in 49 CFR 173.12 and be overpacked... regulations (49 CFR parts 173, 178 and 179), if those regulations specify a particular inside container...

  18. 7 CFR 160.201 - Fees generally for field inspection and certification of naval stores and drum containers of rosin.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... of naval stores and drum containers of rosin. 160.201 Section 160.201 Agriculture Regulations of the... of naval stores and drum containers of rosin. Except as provided in § 160.204, the following fees shall be paid to the United States for the field inspection and certification of naval stores and...

  19. 40 CFR 264.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... in 40 CFR 268.42(c)(1) may use fiber drums in place of metal outer containers. Such fiber drums must... CFR parts 173, 178, and 179), if those regulations specify a particular inside container for the waste... container (49 CFR parts 178 and 179) of no more than 416-liter (110 gallon) capacity and surrounded by, at...

  20. Measurements of the corrosion of low-carbon steel drums under environmental conditions at Hanford: One-year test results

    SciTech Connect

    Duncan, D.R.; Bunnell, L.R.

    1995-05-01

    This report describes the methods used to expose low-carbon steel drums to atmospheric and soil corrosion and describes the methods used to examine specimens retrieved from both types of tests. These drums are being tested to meet requirements of radioactive waste storage for both low-level radioactive wastes and transuranic wastes.

  1. 40 CFR 264.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... CFR parts 173, 178, and 179), if those regulations specify a particular inside container for the waste... container (49 CFR parts 178 and 179) of no more than 416-liter (110 gallon) capacity and surrounded by, at a... in 40 CFR 268.42(c)(1) may use fiber drums in place of metal outer containers. Such fiber drums...

  2. An ABC of Drumming: Children's Narratives about Beat, Rhythm and Groove in a Primary Classroom

    ERIC Educational Resources Information Center

    Mackinlay, Elizabeth

    2014-01-01

    In this paper, I use a bricolage of arts-based research and writing practices to explore narratives by Grade 4 children about their experiences in a drumming circle called "Bam Bam" as represented in a text they created with me called An ABC of drumming. The term "narrative" is used here in a contemporary sense to…

  3. ICE1 of Pyrus ussuriensis functions in cold tolerance by enhancing PuDREBa transcriptional levels through interacting with PuHHP1

    NASA Astrophysics Data System (ADS)

    Huang, Xiaosan; Li, Kongqing; Jin, Cong; Zhang, Shaoling

    2015-12-01

    ICE1 transcription factor plays an important role in plant cold stress via regulating the expression of stress-responsive genes. In this study, a PuICE1 gene isolated from Pyrus ussuriensis was characterized for its function in cold tolerance. The expression levels of the PuICE1 were induced by cold, dehydration and salt, with the greatest induction under cold conditions. PuICE1 was localized in the nucleus and could bind specifically to the MYC element in the PuDREBa promoter. The PuICE1 fused to the GAL4 DNA-binding domain to have transcriptional activation activity. Ectopic expression of the PuICE1 in tomato conferred enhanced tolerance to cold stress at cold temperatures, less electrolyte leakage, less MDA content, higher chlorophyll content, higher survival rate, higher proline content, higher activities of enzymes. In additon, steady-state mRNA levels of six stress-responsive genes coding for either functional or regulatory genes were induced to higher levels in the transgenic lines by cold stress. Yeast two-hybrid, transient assay, split luciferase complementation and BiFC assays all revealed that PuHHP1 protein can physically interact with PuICE1. Taken together, these results demonstrated that PuICE1 plays a positive role in cold tolerance, which may be due to enhancement of PuDREBa transcriptional levels through interacting with the PuHHP1.

  4. ICE1 of Pyrus ussuriensis functions in cold tolerance by enhancing PuDREBa transcriptional levels through interacting with PuHHP1

    PubMed Central

    Huang, Xiaosan; Li, Kongqing; Jin, Cong; Zhang, Shaoling

    2015-01-01

    ICE1 transcription factor plays an important role in plant cold stress via regulating the expression of stress-responsive genes. In this study, a PuICE1 gene isolated from Pyrus ussuriensis was characterized for its function in cold tolerance. The expression levels of the PuICE1 were induced by cold, dehydration and salt, with the greatest induction under cold conditions. PuICE1 was localized in the nucleus and could bind specifically to the MYC element in the PuDREBa promoter. The PuICE1 fused to the GAL4 DNA-binding domain to have transcriptional activation activity. Ectopic expression of the PuICE1 in tomato conferred enhanced tolerance to cold stress at cold temperatures, less electrolyte leakage, less MDA content, higher chlorophyll content, higher survival rate, higher proline content, higher activities of enzymes. In additon, steady-state mRNA levels of six stress-responsive genes coding for either functional or regulatory genes were induced to higher levels in the transgenic lines by cold stress. Yeast two-hybrid, transient assay, split luciferase complementation and BiFC assays all revealed that PuHHP1 protein can physically interact with PuICE1. Taken together, these results demonstrated that PuICE1 plays a positive role in cold tolerance, which may be due to enhancement of PuDREBa transcriptional levels through interacting with the PuHHP1. PMID:26626798

  5. A maximum power point tracking algorithm for buoy-rope-drum wave energy converters

    NASA Astrophysics Data System (ADS)

    Wang, J. Q.; Zhang, X. C.; Zhou, Y.; Cui, Z. C.; Zhu, L. S.

    2016-08-01

    The maximum power point tracking control is the key link to improve the energy conversion efficiency of wave energy converters (WEC). This paper presents a novel variable step size Perturb and Observe maximum power point tracking algorithm with a power classification standard for control of a buoy-rope-drum WEC. The algorithm and simulation model of the buoy-rope-drum WEC are presented in details, as well as simulation experiment results. The results show that the algorithm tracks the maximum power point of the WEC fast and accurately.

  6. Batteryless wireless transmission system for electronic drum uses piezoelectric generator for play signal and power source

    NASA Astrophysics Data System (ADS)

    Nishikawa, H.; Yoshimi, A.; Takemura, K.; Tanaka, A.; Douseki, T.

    2015-12-01

    A batteryless self-powered wireless transmission system has been developed that sends a signal from a drum pad to a synthesizer. The power generated by a piezoelectric generator functions both as the “Play” signal for the synthesizer and as the power source for the transmitter. An FM transmitter, which theoretically operates with zero latency, and a receiver with quick-response squelch of the received signal were developed for wireless transmission with a minimum system delay. Experimental results for an electronic drum without any connecting wires fully demonstrated the feasibility of self-powered wireless transmission with a latency of 900 μs.

  7. Analysis of a boron-carbide-drum-controlled critical reactor experiment

    NASA Technical Reports Server (NTRS)

    Mayo, W. T.

    1972-01-01

    In order to validate methods and cross sections used in the neutronic design of compact fast-spectrum reactors for generating electric power in space, an analysis of a boron-carbide-drum-controlled critical reactor was made. For this reactor the transport analysis gave generally satisfactory results. The calculated multiplication factor for the most detailed calculation was only 0.7-percent Delta k too high. Calculated reactivity worth of the control drums was $11.61 compared to measurements of $11.58 by the inverse kinetics methods and $11.98 by the inverse counting method. Calculated radial and axial power distributions were in good agreement with experiment.

  8. Short-term physiological responses of wild and hatchery-produced red drum during angling

    USGS Publications Warehouse

    Gallman, E.A.; Isely, J.J.; Tomasso, J.R.; Smith, T.I.J.

    1999-01-01

    Serum cortisol concentrations, plasma glucose concentrations, plasma lactate concentrations, and plasma osmolalities increased in red drum Sciaenops ocellatus (26.0-65.5 cm total length) during angling in estuarine waters (17-33 g/L salinity, 21-31??C). Angling time varied from as fast as possible (10 s) to the point when fish ceased resisting (up to 350 s). The increases in the physiological characteristics were similar in wild and hatchery-produced fish. This study indicates that hatchery-produced red drum may be used in catch-and-release studies to simulate the responses of wild fish.

  9. Sources and distributions of 137Cs, 238Pu, 239,240Pu radionuclides in the north-western Barents Sea.

    PubMed

    Zaborska, Agata; Mietelski, Jerzy Wojciech; Carroll, JoLynn; Papucci, Carlo; Pempkowiak, Janusz

    2010-04-01

    Sediment deposits are the ultimate sink for anthropogenic radionuclides entering the marine environment. The major sources of anthropogenic radionuclides to the Barents Sea are fallout from nuclear weapons tests, long range transport from other seas, and river and non-point freshwater supplies. In this study we investigated activity concentrations, ratios, and inventories of the anthropogenic radionuclides, 137Cs, 238Pu, 239,240Pu in dated sediment cores collected along a north-south transect in the northwestern Barents Sea. The data were used to evaluate the influence of different sources on the derived spatial and temporal patterns of anthropogenic radionuclides in seafloor sediment deposits. Activity concentrations of 137Cs ranged from <0.1 Bq/kg to 10.5 Bq/kg while 239,240Pu ranged from <0.01 Bq/kg to 2.74 Bq/kg and 238Pu activity concentrations ranged from <0.01 Bq/kg to 0.22 Bq/kg. Total inventories of 137Cs ranged from 29.5+/-1.5 Bq/m2 to 152.7+/-5.6 Bq/m2 and for 239,240Pu inventories (6 sediment layers only) ranged from 9.5+/-0.3 Bq/m2 to 29.7+/-0.4 Bq/m2. Source contributions varied among stations and between the investigated radionuclides. The 238Pu/239,240Pu ratios up to 0.18 indicate discharges from nuclear fuel reprocessing plants as a main contributor of plutonium. Based on 238Pu/239,240Pu ratio, it was calculated that up to 19-27% of plutonium is supplied from sources other than atmospheric global fallout. Taking into account Atlantic current flow trajectories and that both activity concentrations and inventories of plutonium negatively correlate with latitude, Sellafield is a major source for the Barents Sea. Concentrations and inventories of 137Cs correlate positively with latitude and negatively with distance from the Svalbard archipelago. The 137Cs concentrations are highest in an area of intensive melting of sea ice formed along the Siberian coast. Thus, sea ice and supplies from Svalbard may be important source of 137Cs to the Barents Sea

  10. U, Pu, and Am nuclear signatures of the Thule hydrogen bomb debris.

    PubMed

    Eriksson, Mats; Lindahl, Patric; Roos, Per; Dahlgaard, Henning; Holm, Elis

    2008-07-01

    This study concerns an arctic marine environment that was contaminated by actinide elements after a nuclear accident in 1968, the so-called Thule accident In this study we have analyzed five isolated hot particles as well as sediment samples containing particles from the weapon material for the determination of the nuclear fingerprint of the accident. We report that the fissile material in the hydrogen weapons involved in the Thule accident was a mixture of highly enriched uranium and weapon-grade plutonium and that the main fissile material was 235U (about 4 times more than the mass of 239Pu). In the five hot particles examined, the measured uranium atomic ratio was 235U/238U = 1.02 +/- 0.16 and the Pu-isotopic ratios were as follows: 24Pu/239Pu = 0.0551 +/- 0.0008 (atom ratio), 238Pu/239+240Pu = 0.0161 +/- 0.0005 (activity ratio), 241Pu/239+240Pu = 0.87 +/- 0.12 (activity ratio), and 241Am/ 239+240Pu = 0.169 +/- 0.005 (activity ratio) (reference date 2001-10-01). From the activity ratios of 241Pu/241Am, we estimated the time of production of this weapon material to be from the late 1950s to the early 1960s. The results from reanalyzed bulk sediment samples showed the presence of more than one Pu source involved in the accident, confirming earlier studies. The 238Pu/239+240PU activity ratio and the 240Pu/ 239Pu atomic ratio were divided into at least two Pu-isotopic ratio groups. For both Pu-isotopic ratios, one ratio group had identical ratios as the five hot particles described above and for the other groups the Pu isotopic ratios were lower (238Pu/ 239+240PU activity ratio approximately 0.01 and the 240Pu/P239Pu atomic ratio 0.03). On the studied particles we observed that the U/Pu ratio decreased as a function of the time these particles were present in the sediment. We hypothesis that the decrease in the ratio is due to a preferential leaching of U relative to Pu from the particle matrix. PMID:18677996

  11. U, Pu, and Am nuclear signatures of the Thule hydrogen bomb debris.

    PubMed

    Eriksson, Mats; Lindahl, Patric; Roos, Per; Dahlgaard, Henning; Holm, Elis

    2008-07-01

    This study concerns an arctic marine environment that was contaminated by actinide elements after a nuclear accident in 1968, the so-called Thule accident In this study we have analyzed five isolated hot particles as well as sediment samples containing particles from the weapon material for the determination of the nuclear fingerprint of the accident. We report that the fissile material in the hydrogen weapons involved in the Thule accident was a mixture of highly enriched uranium and weapon-grade plutonium and that the main fissile material was 235U (about 4 times more than the mass of 239Pu). In the five hot particles examined, the measured uranium atomic ratio was 235U/238U = 1.02 +/- 0.16 and the Pu-isotopic ratios were as follows: 24Pu/239Pu = 0.0551 +/- 0.0008 (atom ratio), 238Pu/239+240Pu = 0.0161 +/- 0.0005 (activity ratio), 241Pu/239+240Pu = 0.87 +/- 0.12 (activity ratio), and 241Am/ 239+240Pu = 0.169 +/- 0.005 (activity ratio) (reference date 2001-10-01). From the activity ratios of 241Pu/241Am, we estimated the time of production of this weapon material to be from the late 1950s to the early 1960s. The results from reanalyzed bulk sediment samples showed the presence of more than one Pu source involved in the accident, confirming earlier studies. The 238Pu/239+240PU activity ratio and the 240Pu/ 239Pu atomic ratio were divided into at least two Pu-isotopic ratio groups. For both Pu-isotopic ratios, one ratio group had identical ratios as the five hot particles described above and for the other groups the Pu isotopic ratios were lower (238Pu/ 239+240PU activity ratio approximately 0.01 and the 240Pu/P239Pu atomic ratio 0.03). On the studied particles we observed that the U/Pu ratio decreased as a function of the time these particles were present in the sediment. We hypothesis that the decrease in the ratio is due to a preferential leaching of U relative to Pu from the particle matrix.

  12. Transuranic concentrations in reef and pelagic fish from the Marshall Islands. [/sup 239/Pu, /sup 240/Pu

    SciTech Connect

    Noshkin, V.E.; Eagle, R.J.; Wong, K.M.; Jokela, T.A.

    1980-09-01

    Concentrations of /sup 239 + 240/Pu are reported in tissues of several species of reef and pelagic fish caught at 14 different atolls in the northern Marshall Islands. Several regularities that are species dependent are evident in the distribution of /sup 239 + 240/Pu among different body tissues. Concentrations in liver always exceeded those in bone and concentrations were lowest in the muscle of all fish analyzed. A progressive discrimination against /sup 239 + 240/Pu was observed at successive trophic levels at all atolls except Bikini and Enewetak, where it was difficult to conclude if any real difference exists between the average concentration factor for /sup 239 + 240/Pu among all fish, which include bottom feeding and grazing herbivores, bottom feeding carnivores, and pelagic carnivores from different atoll locations. The average concentration of /sup 239 + 240/Pu in the muscle of surgeonfish from Bikini and Enewetak was not significantly different from the average concentrations determined in these fish at the other, lesser contaminated atolls. Concentrations among all 3rd, 4th, and 5th trophic level species are highest at Bikini where higher environmental concentrations are found. The reasons for the anomalously low concentrations in herbivores from Bikini and Enewetak are not known.

  13. Nuclear Magnetic Resonance Measurements and Electronic Structure of Pu(IV) in [(Me)4N]2PuCl6.

    PubMed

    Mounce, Andrew M; Yasuoka, Hiroshi; Koutroulakis, Georgios; Lee, Jeongseop A; Cho, Herman; Gendron, Frédéric; Zurek, Eva; Scott, Brian L; Trujillo, Julie A; Slemmons, Alice K; Cross, Justin N; Thompson, Joe D; Kozimor, Stosh A; Bauer, Eric D; Autschbach, Jochen; Clark, David L

    2016-09-01

    The synthesis, electronic structure, and characterization via single-crystal X-ray diffraction, nuclear magnetic resonance (NMR) spectroscopy, and magnetic susceptibility of (Me4N)2PuCl6 are reported. NMR measurements were performed to both search for the direct (239)Pu resonance and to obtain local magnetic and electronic information at the Cl site through (35)Cl and (37)Cl spectra. No signature of (239)Pu NMR was observed. The temperature dependence of the Cl spectra was simulated by diagonalizing the Zeeman and quadrupolar Hamiltonians for (35)Cl, (37)Cl, and (14)N isotopes. Electronic structure calculations predict a magnetic Γ5 triplet ground state of Pu(IV) in the crystalline electric field of the undistorted PuCl6 octahedron. A tetragonal distortion would result in a very small splitting (∼20 cm(-1)) of the triplet ground state into a nonmagnetic singlet and a doublet state. The Cl shifts have an inflection point at T ≈ 15 K, differing from the bulk susceptibility, indicating a nonmagnetic crystal field ground state. The Cl spin-lattice relaxation time is constant to T = 15 K, below which it rapidly increases, also supporting the nonmagnetic crystal field ground state.

  14. Deducing the 236Pu(n,f) and 237Pu(n,f) cross sections via the surrogate ratio method

    NASA Astrophysics Data System (ADS)

    Hughes, R. O.; Beausang, C. W.; Ross, T. J.; Burke, J. T.; Casperson, R. J.; McCleskey, M.; Cooper, N.; Escher, J. E.; Gell, K. B.; Good, E.; Humby, P.; Saastimoinen, A.; Tarlow, T. D.

    2013-10-01

    The short half-lives associated with certain minor actinide nuclei that are relevant to stockpile stewardship pursuits and the development of next-generation nuclear reactors make direct neutron measurements very challenging. In certain cases, a stable beam and target ``surrogate reaction'' can be used in lieu of the neutron-induced reaction, and the (n,f) cross section can then be deduced indirectly. Agreement between surrogate and direct measurements for (n,f) cross sections in actinide nuclei is usually within 10%. The present work reports on the measurement of the 236Pu(n,f) and 237Pu(n,f) cross sections via 239Pu(p,tf) and 239Pu(p,df) surrogate reactions, respectively. The experiment was performed at the Texas A&M University Cyclotron Facility using a 28.5 MeV proton beam to bombard 239Pu and 235U targets. Outgoing light ions were detected in coincidence with fission fragments using the STAR-LiTe detector array. Results of the analysis will be presented. This work was supported by DoE Grant Numbers: DE-FG52-09NA29454 and DE-FG02-05ER41379 (Richmond), DE-AC52-07NA27344 (LLNL) and DE-FG52-09NA29467 (TAMU).

  15. Pu236(n,f), Pu237(n,f), and Pu238(n,f) cross sections deduced from (p,t), (p,d), and (p,p') surrogate reactions

    NASA Astrophysics Data System (ADS)

    Hughes, R. O.; Beausang, C. W.; Ross, T. J.; Burke, J. T.; Casperson, R. J.; Cooper, N.; Escher, J. E.; Gell, K.; Good, E.; Humby, P.; McCleskey, M.; Saastimoinen, A.; Tarlow, T. D.; Thompson, I. J.

    2014-07-01

    The Pu236(n,f), Pu237(n,f) and Pu238(n,f) cross sections have been inferred by utilizing the surrogate ratio method. Targets of Pu239 and U235 were bombarded with 28.5-MeV protons, and the light ion recoils, as well as fission fragments, were detected using the STARS detector array at the K150 Cyclotron at the Texas A&M cyclotron facility. The (p, tf) reaction on Pu239 and U235 targets was used to deduce the σ (Pu236(n ,f))/σ(U232(n,f)) ratio, and the Pu236(n,f) cross section was subsequently determined for En=0.5-7.5 MeV. Similarly, the (p,df) reaction on the same two targets was used to deduce the σ(Pu237(n ,f))/σ(U233(n,f)) ratio, and the Pu237(n,f) cross section was extracted in the energy range En=0.5-7 MeV. The Pu238(n,f) cross section was also deduced by utilizing the (p,p') reaction channel on the same targets. There is good agreement with the recent ENDF/B-VII.1 evaluated cross section data for Pu238(n,f) in the range En=0.5-10.5 MeV and for Pu237(n,f) in the range En=0.5-7 MeV; however, the Pu236(n,f) cross section deduced in the present work is higher than the evaluation between 2 and 7 MeV.

  16. Economical Production of Pu-238: NIAC Phase I Final Report

    NASA Technical Reports Server (NTRS)

    Howe, Steven D.; Crawford, Douglas; Navarro, Jorge; O'Brien, Robert C.; Katalenich, Jeff; Ring, Terry

    2016-01-01

    All space exploration missions traveling beyond Jupiter must use radioisotopic power sources for electrical power. The best isotope to power these sources is plutonium-238 (Pu-238). The US supply of Pu-238 is almost exhausted and will be gone within the next decade. The Department of Energy has initiated a production program with a $10M allocation from NASA but the cost is estimated at over $100M to get to production levels. The Center for Space Nuclear Research (CSNR) has conceived of a potentially better process to produce Pu-238 earlier and for significantly less cost. Potentially, the front end capital costs could be provided by private industry such that the government only had to pay for the product produced. In the Phase I NIAC (NASA Innovative Advanced Concepts) grant, the CSNR has evaluated the feasibility of using a low power, commercially available nuclear reactor to produce 1.5 kg of Pu-238 per year. The impact on the neutronics of the reactor have been assessed, the amount of Neptunium target material estimated, and the production rates calculated. In addition, the size of the post-irradiation processing facility has been established. Finally, as the study progressed, a new method for fabricating the Pu-238 product into the form used for power sources has been identified to reduce the cost of the final product. In short, the concept appears to be viable, can produce the amount of Pu-238 needed to support the NASA missions, can be available within a few years, and will cost significantly less than the current DOE program.

  17. Determination of Plutonium Activity Concentrations and 240Pu/239Pu Atom Ratios in Brown Algae (Fucus distichus) Collected from Amchitka Island, Alaska.

    SciTech Connect

    Hamilton, T F; Brown, T A; Marchetti, A A; Martinelli, R E; Kehl, S R

    2005-05-02

    Plutonium-239 ({sup 239}Pu) and plutonium-240 ({sup 240}Pu) activity concentrations and {sup 240}Pu/{sup 239}Pu atom ratios are reported for Brown Algae (Fucus distichus) collected from the littoral zone of Amchitka Island (Alaska) and at a control site on the Alaskan peninsula. Plutonium isotope measurements were performed in replicate using Accelerator Mass Spectrometry (AMS). The average {sup 240}Pu/{sup 239}Pu atom ratio observed in dried Fucus d. collected from Amchitka Island was 0.227 {+-} 0.007 (n=5) and compares with the expected {sup 240}Pu/{sup 239}Pu atom ratio in integrated worldwide fallout deposition in the Northern Hemisphere of 0.1805 {+-} 0.0057 (Cooper et al., 2000). In general, the characteristically high {sup 240}Pu/{sup 239}Pu content of Fucus d. analyzed in this study appear to indicate the presence of a discernible basin-wide secondary source of plutonium entering the marine environment. Of interest to the study of plutonium source terms within the Pacific basin are reports of elevated {sup 240}Pu/{sup 239}Pu atom ratios in fallout debris from high-yield atmospheric nuclear tests conducted in the Marshall Islands during the 1950s (Diamond et al., 1960), the wide range of {sup 240}Pu/{sup 239}Pu atom ratio values (0.19 to 0.34) observed in sea water, sediments, coral and other environmental media from the North Pacific Ocean (Hirose et al., 1992; Buesseler, 1997) and updated estimates of the relative contributions of close-in and intermediate fallout deposition on oceanic inventories of radionuclidies, especially in the Northern Pacific Ocean (Hamilton, 2004).

  18. 7 CFR 160.24a - Inspection as to condition of drums containing rosin and the quality and condition of the rosin...

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Inspection as to condition of drums containing rosin... of drums containing rosin and the quality and condition of the rosin therein upon request. Before or after the shipment in commerce of any lot of rosin in drums from a processing or storage point, and...

  19. 7 CFR 160.24a - Inspection as to condition of drums containing rosin and the quality and condition of the rosin...

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Inspection as to condition of drums containing rosin... of drums containing rosin and the quality and condition of the rosin therein upon request. Before or after the shipment in commerce of any lot of rosin in drums from a processing or storage point, and...

  20. 7 CFR 160.24a - Inspection as to condition of drums containing rosin and the quality and condition of the rosin...

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Inspection as to condition of drums containing rosin... of drums containing rosin and the quality and condition of the rosin therein upon request. Before or after the shipment in commerce of any lot of rosin in drums from a processing or storage point, and...