Science.gov

Sample records for 2012-10-01 false plastic

  1. 49 CFR 178.33b - Specification 2S; inner nonrefillable plastic receptacles.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Specification 2S; inner nonrefillable plastic receptacles. 178.33b Section 178.33b Transportation Other Regulations Relating to Transportation (Continued... nonrefillable plastic receptacles....

  2. 49 CFR 192.59 - Plastic pipe.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Plastic pipe. 192.59 Section 192.59 Transportation... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Materials § 192.59 Plastic pipe. (a) New plastic pipe... specification; and (2) It is resistant to chemicals with which contact may be anticipated. (b) Used plastic...

  3. 49 CFR 192.281 - Plastic pipe.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Plastic pipe. 192.281 Section 192.281... Plastic pipe. (a) General. A plastic pipe joint that is joined by solvent cement, adhesive, or heat fusion may not be disturbed until it has properly set. Plastic pipe may not be joined by a threaded joint...

  4. 49 CFR 178.706 - Standards for rigid plastic IBCs.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Standards for rigid plastic IBCs. 178.706 Section... Performance-Oriented Standards § 178.706 Standards for rigid plastic IBCs. (a) The provisions in this section apply to rigid plastic IBCs intended to contain solids or liquids. Rigid plastic IBC types...

  5. 49 CFR 192.321 - Installation of plastic pipe.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Installation of plastic pipe. 192.321 Section 192... Transmission Lines and Mains § 192.321 Installation of plastic pipe. (a) Plastic pipe must be installed below ground level except as provided by paragraphs (g) and (h) of this section. (b) Plastic pipe that...

  6. 49 CFR 192.193 - Valve installation in plastic pipe.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Valve installation in plastic pipe. 192.193... Components § 192.193 Valve installation in plastic pipe. Each valve installed in plastic pipe must be designed so as to protect the plastic material against excessive torsional or shearing loads when the...

  7. 49 CFR 178.519 - Standards for plastic film bags.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Standards for plastic film bags. 178.519 Section...-bulk Performance-Oriented Packaging Standards § 178.519 Standards for plastic film bags. (a) The identification code for a plastic film bag is 5H4. (b) Construction requirements for plastic film bags are...

  8. 46 CFR 160.010-5 - Buoyant apparatus with plastic foam buoyancy.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 6 2012-10-01 2012-10-01 false Buoyant apparatus with plastic foam buoyancy. 160.010-5... Vessels § 160.010-5 Buoyant apparatus with plastic foam buoyancy. (a) Buoyant apparatus with plastic foam buoyancy must have a plastic foam body with an external protective covering. The body may be reinforced...

  9. 49 CFR 192.121 - Design of plastic pipe.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Design of plastic pipe. 192.121 Section 192.121... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Pipe Design § 192.121 Design of plastic pipe. Subject to the limitations of § 192.123, the design pressure for plastic pipe is determined by either of...

  10. 49 CFR 192.191 - Design pressure of plastic fittings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Design pressure of plastic fittings. 192.191... Components § 192.191 Design pressure of plastic fittings. (a) Thermosetting fittings for plastic pipe must conform to ASTM D 2517, (incorporated by reference, see § 192.7). (b) Thermoplastic fittings for...

  11. 49 CFR 192.311 - Repair of plastic pipe.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Repair of plastic pipe. 192.311 Section 192.311... Lines and Mains § 192.311 Repair of plastic pipe. Each imperfection or damage that would impair the serviceability of plastic pipe must be repaired or removed....

  12. 49 CFR 192.123 - Design limitations for plastic pipe.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Design limitations for plastic pipe. 192.123... Design limitations for plastic pipe. (a) Except as provided in paragraph (e) and paragraph (f) of this section, the design pressure may not exceed a gauge pressure of 100 psig (689 kPa) for plastic pipe...

  13. 49 CFR 192.375 - Service lines: Plastic.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Service lines: Plastic. 192.375 Section 192.375... § 192.375 Service lines: Plastic. (a) Each plastic service line outside a building must be installed... terminate above ground level and outside the building, if— (i) The above ground level part of the...

  14. 49 CFR 192.283 - Plastic pipe: Qualifying joining procedures.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Plastic pipe: Qualifying joining procedures. 192... Materials Other Than by Welding § 192.283 Plastic pipe: Qualifying joining procedures. (a) Heat fusion... for making plastic pipe joints by a heat fusion, solvent cement, or adhesive method, the...

  15. 49 CFR 192.287 - Plastic pipe: Inspection of joints.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Plastic pipe: Inspection of joints. 192.287... Than by Welding § 192.287 Plastic pipe: Inspection of joints. No person may carry out the inspection of joints in plastic pipes required by §§ 192.273(c) and 192.285(b) unless that person has been qualified...

  16. 49 CFR 178.925 - Standards for rigid plastic Large Packagings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Standards for rigid plastic Large Packagings. 178... FOR PACKAGINGS Large Packagings Standards § 178.925 Standards for rigid plastic Large Packagings. (a) The provisions in this section apply to rigid plastic Large Packagings intended to contain liquids...

  17. 49 CFR 192.285 - Plastic pipe: Qualifying persons to make joints.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Plastic pipe: Qualifying persons to make joints... Materials Other Than by Welding § 192.285 Plastic pipe: Qualifying persons to make joints. (a) No person may make a plastic pipe joint unless that person has been qualified under the applicable joining...

  18. 49 CFR 173.221 - Polymeric beads, expandable and Plastic molding compound.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Polymeric beads, expandable and Plastic molding... Than Class 1 and Class 7 § 173.221 Polymeric beads, expandable and Plastic molding compound. (a) Non-bulk shipments of Polymeric beads (or granules), expandable, evolving flammable vapor and...

  19. 46 CFR 26.30-1 - Approved unicellular plastic foam work vests.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 1 2012-10-01 2012-10-01 false Approved unicellular plastic foam work vests. 26.30-1 Section 26.30-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY UNINSPECTED VESSELS OPERATIONS Work Vest § 26.30-1 Approved unicellular plastic foam work vests. (a) Buoyant work vests carried under...

  20. 49 CFR 192.513 - Test requirements for plastic pipelines.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Test requirements for plastic pipelines. 192.513 Section 192.513 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE...

  1. 42 CFR 21.23 - False statements as disqualification.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 42 Public Health 1 2012-10-01 2012-10-01 false False statements as disqualification. 21.23 Section... COMMISSIONED OFFICERS Appointment § 21.23 False statements as disqualification. Willfully false statements shall be cause for rejection of the application or, as provided in subpart N of this part, for dismissal....

  2. 47 CFR 80.1114 - False distress alerts.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 5 2012-10-01 2012-10-01 false False distress alerts. 80.1114 Section 80.1114 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES STATIONS IN THE MARITIME SERVICES Global Maritime Distress and Safety System (GMDSS) Operating Procedures for Distress...

  3. 45 CFR 3.4 - False reports and reports of injury or damage.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 45 Public Welfare 1 2012-10-01 2012-10-01 false False reports and reports of injury or damage. 3.4 Section 3.4 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CONDUCT OF PERSONS AND TRAFFIC ON THE NATIONAL INSTITUTES OF HEALTH FEDERAL ENCLAVE General § 3.4 False reports...

  4. 47 CFR 80.335 - Procedures for canceling false distress alerts.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 5 2012-10-01 2012-10-01 false Procedures for canceling false distress alerts. 80.335 Section 80.335 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES STATIONS IN THE MARITIME SERVICES Safety Watch Requirements and Procedures...

  5. 43 CFR 20.510 - Fraud or false statements in a Government matter.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 43 Public Lands: Interior 1 2012-10-01 2011-10-01 true Fraud or false statements in a Government matter. 20.510 Section 20.510 Public Lands: Interior Office of the Secretary of the Interior EMPLOYEE RESPONSIBILITIES AND CONDUCT Other Employee Conduct Provisions § 20.510 Fraud or false statements in a...

  6. False assumptions.

    PubMed

    Swaminathan, M

    1997-01-01

    Indian women do not have to be told the benefits of breast feeding or "rescued from the clutches of wicked multinational companies" by international agencies. There is no proof that breast feeding has declined in India; in fact, a 1987 survey revealed that 98% of Indian women breast feed. Efforts to promote breast feeding among the middle classes rely on such initiatives as the "baby friendly" hospital where breast feeding is promoted immediately after birth. This ignores the 76% of Indian women who give birth at home. Blaming this unproved decline in breast feeding on multinational companies distracts attention from more far-reaching and intractable effects of social change. While the Infant Milk Substitutes Act is helpful, it also deflects attention from more pressing issues. Another false assumption is that Indian women are abandoning breast feeding to comply with the demands of employment, but research indicates that most women give up employment for breast feeding, despite the economic cost to their families. Women also seek work in the informal sector to secure the flexibility to meet their child care responsibilities. Instead of being concerned about "teaching" women what they already know about the benefits of breast feeding, efforts should be made to remove the constraints women face as a result of their multiple roles and to empower them with the support of families, governmental policies and legislation, employers, health professionals, and the media. PMID:12321627

  7. 49 CFR 192.557 - Uprating: Steel pipelines to a pressure that will produce a hoop stress less than 30 percent of...

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Uprating: Steel pipelines to a pressure that will produce a hoop stress less than 30 percent of SMYS: plastic, cast iron, and ductile iron pipelines. 192.557 Section 192.557 Transportation Other Regulations Relating to Transportation (Continued)...

  8. 46 CFR 160.055-4 - Materials-nonstandard life preservers.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 6 2012-10-01 2012-10-01 false Materials-nonstandard life preservers. 160.055-4 Section..., AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Life Preservers, Unicellular Plastic Foam, Adult and Child, for Merchant Vessels § 160.055-4 Materials—nonstandard life preservers....

  9. 46 CFR 160.050-5 - Sampling, tests, and inspection.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... of the design. (iv) Meet 33 CFR 181.701 through 33 CFR 181.705 which requires an instruction pamphlet... 46 Shipping 6 2012-10-01 2012-10-01 false Sampling, tests, and inspection. 160.050-5 Section 160... Plastic § 160.050-5 Sampling, tests, and inspection. (a) General. Production tests and inspections must...

  10. 46 CFR 160.050-1 - Incorporation by reference.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 6 2012-10-01 2012-10-01 false Incorporation by reference. 160.050-1 Section 160.050-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Specification for a Buoy, Life Ring, Unicellular Plastic §...

  11. 49 CFR 173.166 - Air bag inflators, air bag modules and seat-belt pretensioners.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... plastic or metal containers or dedicated handling devices are authorized for shipment of air bag inflators... 49 Transportation 2 2012-10-01 2012-10-01 false Air bag inflators, air bag modules and seat-belt... Than Class 1 and Class 7 § 173.166 Air bag inflators, air bag modules and seat-belt pretensioners....

  12. 49 CFR 178.975 - Top lift test.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Top lift test. 178.975 Section 178.975... Packagings § 178.975 Top lift test. (a) General. The top lift test must be conducted for the qualification of... the side. (b) Special preparation for the top lift test. (1) Metal and rigid plastic Large...

  13. 49 CFR 178.812 - Top lift test.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Top lift test. 178.812 Section 178.812... Top lift test. (a) General. The top lift test must be conducted for the qualification of all IBC... preparation for the top lift test. (1) Metal, rigid plastic, and composite IBC design types must be loaded...

  14. 46 CFR 160.049-2 - Types and sizes.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 6 2012-10-01 2012-10-01 false Types and sizes. 160.049-2 Section 160.049-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Specification for a Buoyant Cushion Plastic Foam §...

  15. 46 CFR 160.053-4 - Inspections and tests.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 6 2012-10-01 2012-10-01 false Inspections and tests. 160.053-4 Section 160.053-4 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Work Vests, Unicellular Plastic Foam § 160.053-4 Inspections...

  16. 46 CFR 160.053-5 - Marking.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 6 2012-10-01 2012-10-01 false Marking. 160.053-5 Section 160.053-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Work Vests, Unicellular Plastic Foam § 160.053-5 Marking....

  17. 46 CFR 160.049-6 - Marking.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 6 2012-10-01 2012-10-01 false Marking. 160.049-6 Section 160.049-6 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Specification for a Buoyant Cushion Plastic Foam §...

  18. 46 CFR 160.052-2 - Size and model.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 6 2012-10-01 2012-10-01 false Size and model. 160.052-2 Section 160.052-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Specification for a Buoyant Vest, Unicellular Plastic...

  19. 46 CFR 160.052-8 - Marking.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 6 2012-10-01 2012-10-01 false Marking. 160.052-8 Section 160.052-8 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Specification for a Buoyant Vest, Unicellular Plastic...

  20. 46 CFR 160.055-8 - Marking.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 6 2012-10-01 2012-10-01 false Marking. 160.055-8 Section 160.055-8 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Life Preservers, Unicellular Plastic Foam, Adult and Child,...

  1. 46 CFR 160.055-2 - Type and model.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 6 2012-10-01 2012-10-01 false Type and model. 160.055-2 Section 160.055-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Life Preservers, Unicellular Plastic Foam, Adult and Child,...

  2. 49 CFR 192.511 - Test requirements for service lines.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Test requirements for service lines. 192.511... Test requirements for service lines. (a) Each segment of a service line (other than plastic) must be... test at the operating pressure when placed in service. (b) Each segment of a service line (other...

  3. 46 CFR 160.053-3 - Materials, construction and workmanship.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 6 2012-10-01 2012-10-01 false Materials, construction and workmanship. 160.053-3..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Work Vests, Unicellular Plastic Foam § 160.053-3 Materials, construction and workmanship. (a) General. Except as otherwise...

  4. Regulatory false positives: true, false, or uncertain?

    PubMed

    Cox, Louis Anthony

    2007-10-01

    Hansen et al. (2007) recently assessed the historical performance of the precautionary principle in 88 specific cases, concluding that "applying our definition of a regulatory false positive, we were able to identify only four cases that fit the definition of a false positive." Empirically evaluating how prone the precautionary principle is to classify nonproblems as problems ("false positives") is an excellent idea. Yet, Hansen et al.'s implementation of this idea applies a diverse set of questionable criteria to label many highly uncertain risks as "real" even when no real or potential harm has actually been demonstrated. Examples include treating each of the following as reasons to categorize risks as "real": considering that a company's actions contaminated its own product; lack of a known exposure threshold for health effects; occurrence of a threat; treating deliberately conservative (upper-bound) regulatory assumptions as if they were true values; treating assumed exposures of children to contaminated soils (by ingestion) as evidence that feared dioxin risks are real; and treating claimed (sometimes ambiguous) epidemiological associations as if they were known to be true causal relations. Such criteria can classify even nonexistent and unknown risks as "real," providing an alternative possible explanation for why the authors failed to find more false positives, even if they exist.

  5. The False Aneurysm

    PubMed Central

    Baird, R. J.; Doran, M. L.

    1964-01-01

    The clinical course of 18 patients with 25 false aneurysms is reviewed. In recent years false aneurysm has been most commonly seen as a complication of arterioplastic procedures in which prosthetic arterial grafts were used. The use of indwelling needles or cannulae, particularly in patients with a wide arterial pulse pressure, can also lead to the formation of false aneurysms. In the groin, a false aneurysm is frequently mistaken for an abscess. Early diagnosis and operative repair are essential to reduce the incidence of further complications. PMID:14180533

  6. False memories in schizophrenia.

    PubMed

    Moritz, Steffen; Woodward, Todd S; Cuttler, Carrie; Whitman, Jennifer C; Watson, Jason M

    2004-04-01

    In prior studies, it was observed that patients with schizophrenia show abnormally high knowledge corruption (i.e., high-confident errors expressed as a percentage of all high-confident responses were increased for schizophrenic patients relative to controls). The authors examined the conditions under which excessive knowledge corruption occurred using the Deese-Roediger-McDermott paradigm. Whereas knowledge corruption in schizophrenia was significantly greater for false-negative errors relative to controls, no group difference occurred for false-positive errors. The groups showed a comparable high degree of confidence for false-positive recognition of critical lure items. Similar to findings collected in elderly participants, patients, but not controls, showed a strong positive correlation between the number of recognized studied items and false-positive recognition of the critical lure.

  7. Plastic Surgery

    MedlinePlus

    ... How Can I Help a Friend Who Cuts? Plastic Surgery KidsHealth > For Teens > Plastic Surgery Print A ... her forehead lightened with a laser? What Is Plastic Surgery? Just because the name includes the word " ...

  8. 49 CFR 192.281 - Plastic pipe.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Plastic pipe. 192.281 Section 192.281... Plastic pipe. (a) General. A plastic pipe joint that is joined by solvent cement, adhesive, or heat fusion may not be disturbed until it has properly set. Plastic pipe may not be joined by a threaded joint...

  9. 49 CFR 192.281 - Plastic pipe.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Plastic pipe. 192.281 Section 192.281... Plastic pipe. (a) General. A plastic pipe joint that is joined by solvent cement, adhesive, or heat fusion may not be disturbed until it has properly set. Plastic pipe may not be joined by a threaded joint...

  10. 49 CFR 192.59 - Plastic pipe.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Plastic pipe. 192.59 Section 192.59 Transportation... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Materials § 192.59 Plastic pipe. (a) New plastic pipe... specification; and (2) It is resistant to chemicals with which contact may be anticipated. (b) Used plastic...

  11. 49 CFR 192.59 - Plastic pipe.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Plastic pipe. 192.59 Section 192.59 Transportation... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Materials § 192.59 Plastic pipe. (a) New plastic pipe... specification; and (2) It is resistant to chemicals with which contact may be anticipated. (b) Used plastic...

  12. 49 CFR 192.281 - Plastic pipe.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Plastic pipe. 192.281 Section 192.281... Plastic pipe. (a) General. A plastic pipe joint that is joined by solvent cement, adhesive, or heat fusion may not be disturbed until it has properly set. Plastic pipe may not be joined by a threaded joint...

  13. 49 CFR 192.281 - Plastic pipe.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Plastic pipe. 192.281 Section 192.281... Plastic pipe. (a) General. A plastic pipe joint that is joined by solvent cement, adhesive, or heat fusion may not be disturbed until it has properly set. Plastic pipe may not be joined by a threaded joint...

  14. 49 CFR 192.59 - Plastic pipe.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Plastic pipe. 192.59 Section 192.59 Transportation... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Materials § 192.59 Plastic pipe. (a) New plastic pipe... specification; and (2) It is resistant to chemicals with which contact may be anticipated. (b) Used plastic...

  15. 49 CFR 192.59 - Plastic pipe.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Plastic pipe. 192.59 Section 192.59 Transportation... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Materials § 192.59 Plastic pipe. (a) New plastic pipe... specification; and (2) It is resistant to chemicals with which contact may be anticipated. (b) Used plastic...

  16. Moon - False Color Mosaic

    NASA Technical Reports Server (NTRS)

    1992-01-01

    This false-color photograph is a composite of 15 images of the Moon taken through three color filters by Galileo's solid-state imaging system during the spacecraft's passage through the Earth-Moon system on December 8, 1992. When this view was obtained, the spacecraft was 425,000 kilometers (262,000 miles) from the Moon and 69,000 kilometers (43,000 miles) from Earth. The false-color processing used to create this lunar image is helpful for interpreting the surface soil composition. Areas appearing red generally correspond to the lunar highlands, while blue to orange shades indicate the ancient volcanic lava flow of a mare, or lunar sea. Bluer mare areas contain more titanium than do the orange regions. Mare Tranquillitatis, seen as a deep blue patch on the right, is richer in titanium than Mare Serenitatis, a slightly smaller circular area immediately adjacent to the upper left of Mare Tranquillitatis. Blue and orange areas covering much of the left side of the Moon in this view represent many separate lava flows in Oceanus Procellarum. The small purple areas found near the center are pyroclastic deposits formed by explosive volcanic eruptions. The fresh crater Tycho, with a diameter of 85 kilometers (53 miles), is prominent at the bottom of the photograph, where part of the Moon's disk is missing.

  17. False color viewing device

    DOEpatents

    Kronberg, J.W.

    1991-05-08

    This invention consists of a viewing device for observing objects in near-infrared false-color comprising a pair of goggles with one or more filters in the apertures, and pads that engage the face for blocking stray light from the sides so that all light reaching, the user`s eyes come through the filters. The filters attenuate most visible light and pass near-infrared (having wavelengths longer than approximately 700 nm) and a small amount of blue-green and blue-violet (having wavelengths in the 500 to 520 nm and shorter than 435 nm, respectively). The goggles are useful for looking at vegetation to identify different species and for determining the health of the vegetation, and to detect some forms of camouflage.

  18. False color viewing device

    DOEpatents

    Kronberg, J.W.

    1992-10-20

    A viewing device for observing objects in near-infrared false-color comprising a pair of goggles with one or more filters in the apertures, and pads that engage the face for blocking stray light from the sides so that all light reaching the user's eyes come through the filters. The filters attenuate most visible light and pass near-infrared (having wavelengths longer than approximately 700 nm) and a small amount of blue-green and blue-violet (having wavelengths in the 500 to 520 nm and shorter than 435 nm, respectively). The goggles are useful for looking at vegetation to identify different species and for determining the health of the vegetation, and to detect some forms of camouflage. 7 figs.

  19. False color viewing device

    DOEpatents

    Kronberg, James W.

    1992-01-01

    A viewing device for observing objects in near-infrared false-color comprising a pair of goggles with one or more filters in the apertures, and pads that engage the face for blocking stray light from the sides so that all light reaching the user's eyes come through the filters. The filters attenuate most visible light and pass near-infrared (having wavelengths longer than approximately 700 nm) and a small amount of blue-green and blue-violet (having wavelengths in the 500 to 520 nm and shorter than 435 nm, respectively). The goggles are useful for looking at vegetation to identify different species and for determining the health of the vegetation, and to detect some forms of camouflage.

  20. Plastic Jellyfish.

    ERIC Educational Resources Information Center

    Moseley, Christine

    2000-01-01

    Presents an environmental science activity designed to enhance students' awareness of the hazards of plastic waste for wildlife in aquatic environments. Discusses how students can take steps to reduce the effects of plastic waste. (WRM)

  1. 7 CFR 58.326 - Plastic cream.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Plastic cream. 58.326 Section 58.326 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Material § 58.326 Plastic cream. To produce plastic cream eligible for official certification, the...

  2. 7 CFR 58.326 - Plastic cream.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Plastic cream. 58.326 Section 58.326 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Material § 58.326 Plastic cream. To produce plastic cream eligible for official certification, the...

  3. 7 CFR 58.326 - Plastic cream.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Plastic cream. 58.326 Section 58.326 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Material § 58.326 Plastic cream. To produce plastic cream eligible for official certification, the...

  4. 7 CFR 58.326 - Plastic cream.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Plastic cream. 58.326 Section 58.326 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Material § 58.326 Plastic cream. To produce plastic cream eligible for official certification, the...

  5. 7 CFR 58.326 - Plastic cream.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Plastic cream. 58.326 Section 58.326 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Material § 58.326 Plastic cream. To produce plastic cream eligible for official certification, the...

  6. False Position, Double False Position and Cramer's Rule

    ERIC Educational Resources Information Center

    Boman, Eugene

    2009-01-01

    We state and prove the methods of False Position (Regula Falsa) and Double False Position (Regula Duorum Falsorum). The history of both is traced from ancient Egypt and China through the work of Fibonacci, ending with a connection between Double False Position and Cramer's Rule.

  7. Plastics Technology.

    ERIC Educational Resources Information Center

    Barker, Tommy G.

    This curriculum guide is designed to assist junior high schools industrial arts teachers in planning new courses and revising existing courses in plastics technology. Addressed in the individual units of the guide are the following topics: introduction to production technology; history and development of plastics; safety; youth leadership,…

  8. The Kepler False Positive Table

    NASA Astrophysics Data System (ADS)

    Bryson, Steve; Kepler False Positive Working Group

    2015-01-01

    The Kepler Space Telescope has detected thousands of candidate exoplanets by observing transit signals in a sample of more than 190,000 stars. Many of these transit signals are false positives, defined as a transit-like signal that is not due to a planet orbiting the target star (or a bound companion if the target is a multiple-star system). Astrophysical causes of false positives include background eclipsing binaries, planetary transits not associated with the target star, and non-planetary eclipses of the target star by stellar companions. The fraction of Kepler planet candidates that are false positives ranges from about 10% at high Galactic latitudes to 40% at low Galactic latitudes. Creating a high-reliability planet candidate catalog for statistical studies such as occurrence rate calculations requires removing clearly identified false positives.The Kepler Object of Interest (KOI) catalog at the NExScI NASA Exoplanet Archive flags false positives, and will soon provide a high-level classification of false positives, but lacks detailed description of why a KOI was determined to be a false positive. The Kepler False Positive Working Group (FPWG) examines each false positive in detail to certify that it is correctly identified as a false positive, and determines the primary reason(s) a KOI is classified as a false positive. The work of the FPWG will be published as the Kepler False Positive Table, hosted at the NExScI NASA Exoplanet Archive.The Kepler False Positive Table provides detailed information on the evidence for background binaries, transits caused by stellar companions, and false alarms. In addition to providing insight into the Kepler false positive population, the false positive table gives information about the background binary population and other areas of astrophysical interest. Because a planet around a star not associated with the target star is considered a false positive, the false positive table likely contains further planet candidates

  9. Sleep deprivation and false memories.

    PubMed

    Frenda, Steven J; Patihis, Lawrence; Loftus, Elizabeth F; Lewis, Holly C; Fenn, Kimberly M

    2014-09-01

    Many studies have investigated factors that affect susceptibility to false memories. However, few have investigated the role of sleep deprivation in the formation of false memories, despite overwhelming evidence that sleep deprivation impairs cognitive function. We examined the relationship between self-reported sleep duration and false memories and the effect of 24 hr of total sleep deprivation on susceptibility to false memories. We found that under certain conditions, sleep deprivation can increase the risk of developing false memories. Specifically, sleep deprivation increased false memories in a misinformation task when participants were sleep deprived during event encoding, but did not have a significant effect when the deprivation occurred after event encoding. These experiments are the first to investigate the effect of sleep deprivation on susceptibility to false memories, which can have dire consequences.

  10. 33 CFR 183.552 - Plastic encased fuel tanks: Installation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Plastic encased fuel tanks... § 183.552 Plastic encased fuel tanks: Installation. (a) Each fuel tank encased in cellular plastic foam or in fiber reinforced plastic must have the connections, fittings, and labels accessible...

  11. 49 CFR 178.519 - Standards for plastic film bags.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Standards for plastic film bags. 178.519 Section...-bulk Performance-Oriented Packaging Standards § 178.519 Standards for plastic film bags. (a) The identification code for a plastic film bag is 5H4. (b) Construction requirements for plastic film bags are...

  12. 49 CFR 178.706 - Standards for rigid plastic IBCs.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Standards for rigid plastic IBCs. 178.706 Section... Performance-Oriented Standards § 178.706 Standards for rigid plastic IBCs. (a) The provisions in this section apply to rigid plastic IBCs intended to contain solids or liquids. Rigid plastic IBC types...

  13. 33 CFR 183.552 - Plastic encased fuel tanks: Installation.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Plastic encased fuel tanks... § 183.552 Plastic encased fuel tanks: Installation. (a) Each fuel tank encased in cellular plastic foam or in fiber reinforced plastic must have the connections, fittings, and labels accessible...

  14. 49 CFR 178.706 - Standards for rigid plastic IBCs.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Standards for rigid plastic IBCs. 178.706 Section... Performance-Oriented Standards § 178.706 Standards for rigid plastic IBCs. (a) The provisions in this section apply to rigid plastic IBCs intended to contain solids or liquids. Rigid plastic IBC types...

  15. 33 CFR 183.552 - Plastic encased fuel tanks: Installation.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false Plastic encased fuel tanks... § 183.552 Plastic encased fuel tanks: Installation. (a) Each fuel tank encased in cellular plastic foam or in fiber reinforced plastic must have the connections, fittings, and labels accessible...

  16. 49 CFR 192.193 - Valve installation in plastic pipe.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Valve installation in plastic pipe. 192.193... Components § 192.193 Valve installation in plastic pipe. Each valve installed in plastic pipe must be designed so as to protect the plastic material against excessive torsional or shearing loads when the...

  17. 33 CFR 183.552 - Plastic encased fuel tanks: Installation.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Plastic encased fuel tanks... § 183.552 Plastic encased fuel tanks: Installation. (a) Each fuel tank encased in cellular plastic foam or in fiber reinforced plastic must have the connections, fittings, and labels accessible...

  18. 49 CFR 192.321 - Installation of plastic pipe.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Installation of plastic pipe. 192.321 Section 192... Transmission Lines and Mains § 192.321 Installation of plastic pipe. (a) Plastic pipe must be installed below ground level except as provided by paragraphs (g) and (h) of this section. (b) Plastic pipe that...

  19. 49 CFR 192.321 - Installation of plastic pipe.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Installation of plastic pipe. 192.321 Section 192... Transmission Lines and Mains § 192.321 Installation of plastic pipe. (a) Plastic pipe must be installed below ground level except as provided by paragraphs (g) and (h) of this section. (b) Plastic pipe that...

  20. 49 CFR 192.193 - Valve installation in plastic pipe.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Valve installation in plastic pipe. 192.193... Components § 192.193 Valve installation in plastic pipe. Each valve installed in plastic pipe must be designed so as to protect the plastic material against excessive torsional or shearing loads when the...

  1. 49 CFR 178.519 - Standards for plastic film bags.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Standards for plastic film bags. 178.519 Section...-bulk Performance-Oriented Packaging Standards § 178.519 Standards for plastic film bags. (a) The identification code for a plastic film bag is 5H4. (b) Construction requirements for plastic film bags are...

  2. 33 CFR 183.552 - Plastic encased fuel tanks: Installation.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false Plastic encased fuel tanks... § 183.552 Plastic encased fuel tanks: Installation. (a) Each fuel tank encased in cellular plastic foam or in fiber reinforced plastic must have the connections, fittings, and labels accessible...

  3. 49 CFR 192.193 - Valve installation in plastic pipe.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Valve installation in plastic pipe. 192.193... Components § 192.193 Valve installation in plastic pipe. Each valve installed in plastic pipe must be designed so as to protect the plastic material against excessive torsional or shearing loads when the...

  4. 49 CFR 192.193 - Valve installation in plastic pipe.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Valve installation in plastic pipe. 192.193... Components § 192.193 Valve installation in plastic pipe. Each valve installed in plastic pipe must be designed so as to protect the plastic material against excessive torsional or shearing loads when the...

  5. 21 CFR 878.3925 - Plastic surgery kit and accessories.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Plastic surgery kit and accessories. 878.3925... (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Prosthetic Devices § 878.3925 Plastic surgery kit and accessories. (a) Identification. A plastic surgery kit and accessories is a device intended...

  6. 21 CFR 878.3925 - Plastic surgery kit and accessories.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Plastic surgery kit and accessories. 878.3925... (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Prosthetic Devices § 878.3925 Plastic surgery kit and accessories. (a) Identification. A plastic surgery kit and accessories is a device intended...

  7. 21 CFR 878.3925 - Plastic surgery kit and accessories.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Plastic surgery kit and accessories. 878.3925... (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Prosthetic Devices § 878.3925 Plastic surgery kit and accessories. (a) Identification. A plastic surgery kit and accessories is a device intended...

  8. 21 CFR 878.3925 - Plastic surgery kit and accessories.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Plastic surgery kit and accessories. 878.3925... (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Prosthetic Devices § 878.3925 Plastic surgery kit and accessories. (a) Identification. A plastic surgery kit and accessories is a device intended...

  9. 21 CFR 878.3925 - Plastic surgery kit and accessories.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Plastic surgery kit and accessories. 878.3925... (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Prosthetic Devices § 878.3925 Plastic surgery kit and accessories. (a) Identification. A plastic surgery kit and accessories is a device intended...

  10. 49 CFR 192.321 - Installation of plastic pipe.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Transmission Lines and Mains § 192.321 Installation of plastic pipe. (a) Plastic pipe must be installed below ground level except as provided by paragraphs (g) and (h) of this section. (b) Plastic pipe that is... 49 Transportation 3 2010-10-01 2010-10-01 false Installation of plastic pipe. 192.321 Section...

  11. 49 CFR 192.321 - Installation of plastic pipe.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Transmission Lines and Mains § 192.321 Installation of plastic pipe. (a) Plastic pipe must be installed below ground level except as provided by paragraphs (g) and (h) of this section. (b) Plastic pipe that is... 49 Transportation 3 2011-10-01 2011-10-01 false Installation of plastic pipe. 192.321 Section...

  12. 49 CFR 178.519 - Standards for plastic film bags.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Standards for plastic film bags. 178.519 Section... PACKAGINGS Non-bulk Performance-Oriented Packaging Standards § 178.519 Standards for plastic film bags. (a) The identification code for a plastic film bag is 5H4. (b) Construction requirements for plastic...

  13. Reduced False Memory after Sleep

    ERIC Educational Resources Information Center

    Fenn, Kimberly M.; Gallo, David A.; Margoliash, Daniel; Roediger, Henry L., III; Nusbaum, Howard C.

    2009-01-01

    Several studies have shown that sleep contributes to the successful maintenance of previously encoded information. This research has focused exclusively on memory for studied events, as opposed to false memories. Here we report three experiments showing that sleep reduces false memories in the Deese-Roediger-McDermott (DRM) memory illusion. False…

  14. Executive Functioning and Preschoolers' Understanding of False Beliefs, False Photographs, and False Signs

    ERIC Educational Resources Information Center

    Sabbagh, Mark A.; Moses, Louis J.; Shiverick, Sean

    2006-01-01

    Two studies were conducted to investigate the specificity of the relationship between preschoolers' emerging executive functioning skills and false belief understanding. Study 1 (N=44) showed that 3- to 5-year-olds' performance on an executive functioning task that required selective suppression of actions predicted performance on false belief…

  15. Plastic condoms.

    PubMed

    1968-01-01

    Only simple equipment, simple technology and low initial capital investment are needed in their manufacture. The condoms can be made by people who were previously unskilled or only semi-skilled workers. Plastic condoms differ from those made of latex rubber in that the nature of the plastic film allows unlimited shelf-life. Also, the plastic has a higher degree of lubricity than latex rubber; if there is a demand for extra lubrication in a particular market, this can be provided. Because the plastic is inert, these condoms need not be packaged in hermetically sealed containers. All these attributes make it possible to put these condoms on the distributors' shelves in developing countries competitively with rubber condoms. The shape of the plastic condom is based on that of the lamb caecum, which has long been used as luxury-type condom. The plastic condom is made from plastic film (ethylene ethyl acrilate) of 0.001 inch (0.0254 mm.) thickness. In addition, a rubber ring is provided and sealed into the base of the condom for retention during coitus. The advantage of the plastic condom design and the equipment on which it is made is that production can be carried out either in labour-intensive economy or with varying degrees of mechanization and automation. The uniform, finished condom if made using previously untrained workers. Training of workers can be done in a matter of hours on the two machines which are needed to produce and test the condoms. The plastic film is provided on a double wound roll, and condom blanks are prepared by means of a heat-sealing die on the stamping machine. The rubber rings are united to the condom blanks on an assembly machine, which consists of a mandrel and heat-sealing equipment to seal the rubber ring to the base of the condom. Built into the assembly machine is a simple air-testing apparatus that can detect the smallest pinhole flaw in a condom. The manufacturing process is completed by unravelling the condom from the assembly

  16. Sleep deprivation and false confessions.

    PubMed

    Frenda, Steven J; Berkowitz, Shari R; Loftus, Elizabeth F; Fenn, Kimberly M

    2016-02-23

    False confession is a major contributor to the problem of wrongful convictions in the United States. Here, we provide direct evidence linking sleep deprivation and false confessions. In a procedure adapted from Kassin and Kiechel [(1996) Psychol Sci 7(3):125-128], participants completed computer tasks across multiple sessions and repeatedly received warnings that pressing the "Escape" key on their keyboard would cause the loss of study data. In their final session, participants either slept all night in laboratory bedrooms or remained awake all night. In the morning, all participants were asked to sign a statement, which summarized their activities in the laboratory and falsely alleged that they pressed the Escape key during an earlier session. After a single request, the odds of signing were 4.5 times higher for the sleep-deprived participants than for the rested participants. These findings have important implications and highlight the need for further research on factors affecting true and false confessions. PMID:26858426

  17. Sleep deprivation and false confessions.

    PubMed

    Frenda, Steven J; Berkowitz, Shari R; Loftus, Elizabeth F; Fenn, Kimberly M

    2016-02-23

    False confession is a major contributor to the problem of wrongful convictions in the United States. Here, we provide direct evidence linking sleep deprivation and false confessions. In a procedure adapted from Kassin and Kiechel [(1996) Psychol Sci 7(3):125-128], participants completed computer tasks across multiple sessions and repeatedly received warnings that pressing the "Escape" key on their keyboard would cause the loss of study data. In their final session, participants either slept all night in laboratory bedrooms or remained awake all night. In the morning, all participants were asked to sign a statement, which summarized their activities in the laboratory and falsely alleged that they pressed the Escape key during an earlier session. After a single request, the odds of signing were 4.5 times higher for the sleep-deprived participants than for the rested participants. These findings have important implications and highlight the need for further research on factors affecting true and false confessions.

  18. Cosmetic Plastic Surgery Statistics

    MedlinePlus

    2014 Cosmetic Plastic Surgery Statistics Cosmetic Procedure Trends 2014 Plastic Surgery Statistics Report Please credit the AMERICAN SOCIETY OF PLASTIC SURGEONS when citing statistical data or using ...

  19. Plastics Technician.

    ERIC Educational Resources Information Center

    Ohio State Univ., Columbus. Center on Education and Training for Employment.

    This document contains 16 units to consider for use in a tech prep competency profile for the occupation of plastics technician. All the units listed will not necessarily apply to every situation or tech prep consortium, nor will all the competencies within each unit be appropriate. Several units appear within each specific occupation and would…

  20. False rape: a case report.

    PubMed

    Fanton, L; Schoendorff, P; Achache, P; Miras, A; Malicier, D

    1999-12-01

    A 16-year-old girl was admitted to the emergency department for sexual assault. The forensic examination revealed genital lesions of an age that were incompatible with her statements. She also presented extragenital lesions that resembled self-inflicted lesions. The reports of false rape allegations in the literature have all dealt with the motivations of the false victims. This case report is a reminder that an allegation of rape can be considered only on the basis of proof and not on speculation. PMID:10624933

  1. Evolutionary Psychology and False Confession

    ERIC Educational Resources Information Center

    Bering, Jesse M.; Shackelford, Todd K.

    2005-01-01

    This paper presents comments on Kassin's review, (see record 2005-03019-002) of the psychology of false confessions. The authors note that Kassin's review makes a compelling argument for the need for legal reform in police interrogation practices. Because his work strikes at the heart of the American criminal justice system--its fairness--the…

  2. Sleep deprivation and false confessions

    PubMed Central

    Frenda, Steven J.; Berkowitz, Shari R.; Loftus, Elizabeth F.; Fenn, Kimberly M.

    2016-01-01

    False confession is a major contributor to the problem of wrongful convictions in the United States. Here, we provide direct evidence linking sleep deprivation and false confessions. In a procedure adapted from Kassin and Kiechel [(1996) Psychol Sci 7(3):125–128], participants completed computer tasks across multiple sessions and repeatedly received warnings that pressing the “Escape” key on their keyboard would cause the loss of study data. In their final session, participants either slept all night in laboratory bedrooms or remained awake all night. In the morning, all participants were asked to sign a statement, which summarized their activities in the laboratory and falsely alleged that they pressed the Escape key during an earlier session. After a single request, the odds of signing were 4.5 times higher for the sleep-deprived participants than for the rested participants. These findings have important implications and highlight the need for further research on factors affecting true and false confessions. PMID:26858426

  3. Sleep Loss Produces False Memories

    PubMed Central

    Diekelmann, Susanne; Landolt, Hans-Peter; Lahl, Olaf; Born, Jan; Wagner, Ullrich

    2008-01-01

    People sometimes claim with high confidence to remember events that in fact never happened, typically due to strong semantic associations with actually encoded events. Sleep is known to provide optimal neurobiological conditions for consolidation of memories for long-term storage, whereas sleep deprivation acutely impairs retrieval of stored memories. Here, focusing on the role of sleep-related memory processes, we tested whether false memories can be created (a) as enduring memory representations due to a consolidation-associated reorganization of new memory representations during post-learning sleep and/or (b) as an acute retrieval-related phenomenon induced by sleep deprivation at memory testing. According to the Deese, Roediger, McDermott (DRM) false memory paradigm, subjects learned lists of semantically associated words (e.g., “night”, “dark”, “coal”,…), lacking the strongest common associate or theme word (here: “black”). Subjects either slept or stayed awake immediately after learning, and they were either sleep deprived or not at recognition testing 9, 33, or 44 hours after learning. Sleep deprivation at retrieval, but not sleep following learning, critically enhanced false memories of theme words. This effect was abolished by caffeine administration prior to retrieval, indicating that adenosinergic mechanisms can contribute to the generation of false memories associated with sleep loss. PMID:18946511

  4. MSPI False Indication Probability Simulations

    SciTech Connect

    Dana Kelly; Kurt Vedros; Robert Youngblood

    2011-03-01

    This paper examines false indication probabilities in the context of the Mitigating System Performance Index (MSPI), in order to investigate the pros and cons of different approaches to resolving two coupled issues: (1) sensitivity to the prior distribution used in calculating the Bayesian-corrected unreliability contribution to the MSPI, and (2) whether (in a particular plant configuration) to model the fuel oil transfer pump (FOTP) as a separate component, or integrally to its emergency diesel generator (EDG). False indication probabilities were calculated for the following situations: (1) all component reliability parameters at their baseline values, so that the true indication is green, meaning that an indication of white or above would be false positive; (2) one or more components degraded to the extent that the true indication would be (mid) white, and “false” would be green (negative) or yellow (negative) or red (negative). In key respects, this was the approach taken in NUREG-1753. The prior distributions examined were the constrained noninformative (CNI) prior used currently by the MSPI, a mixture of conjugate priors, the Jeffreys noninformative prior, a nonconjugate log(istic)-normal prior, and the minimally informative prior investigated in (Kelly et al., 2010). The mid-white performance state was set at ?CDF = ?10 ? 10-6/yr. For each simulated time history, a check is made of whether the calculated ?CDF is above or below 10-6/yr. If the parameters were at their baseline values, and ?CDF > 10-6/yr, this is counted as a false positive. Conversely, if one or all of the parameters are set to values corresponding to ?CDF > 10-6/yr but that time history’s ?CDF < 10-6/yr, this is counted as a false negative indication. The false indication (positive or negative) probability is then estimated as the number of false positive or negative counts divided by the number of time histories (100,000). Results are presented for a set of base case parameter values

  5. Plastic bronchitis.

    PubMed

    Singhi, Anil Kumar; Vinoth, Bharathi; Kuruvilla, Sarah; Sivakumar, Kothandam

    2015-01-01

    Plastic bronchitis, a rare but serious clinical condition, commonly seen after Fontan surgeries in children, may be a manifestation of suboptimal adaptation to the cavopulmonary circulation with unfavorable hemodynamics. They are ominous with poor prognosis. Sometimes, infection or airway reactivity may provoke cast bronchitis as a two-step insult on a vulnerable vascular bed. In such instances, aggressive management leads to longer survival. This report of cast bronchitis discusses its current understanding. PMID:26556975

  6. Outcome Knowledge and False Belief

    PubMed Central

    Ghrear, Siba E.; Birch, Susan A. J.; Bernstein, Daniel M.

    2016-01-01

    Virtually every social interaction involves reasoning about the perspectives of others, or ‘theory of mind (ToM).’ Previous research suggests that it is difficult to ignore our current knowledge when reasoning about a more naïve perspective (i.e., the curse of knowledge). In this Mini Review, we discuss the implications of the curse of knowledge for certain aspects of ToM. Particularly, we examine how the curse of knowledge influences key measurements of false belief reasoning. In closing, we touch on the need to develop new measurement tools to discern the mechanisms involved in the curse of knowledge and false belief reasoning, and how they develop across the lifespan. PMID:26903922

  7. [False innovations in clinical research].

    PubMed

    Garattini, Silvio; Bertele', Vittorio

    2006-11-01

    Pharmaceutical innovation is actually poorer than it seems, largely because of "false" innovations. Various factors help create an image of novelty in the pharmaceutical area. These factors act throughout the research and development process and in the post-marketing stages affecting the selection of study hypotheses, the adoption of the appropriate study methodology, and the interpretation and publication of results. Each of these steps may be diverted from the priority objective of patients' interest and shifted towards to the defence of the drugs companies' commercial interests. Regulators, NHS, physicians and patients must be vigilant to recognise and get rid of false innovations which can prevent the use of more effective and safer drugs and waste resources useful for effective treatments in other areas. Rewarding this lack of innovation discourages research for excellence and reduces the competitiveness of the pharmaceutical industry. PMID:17252717

  8. [False innovations in clinical research].

    PubMed

    Garattini, Silvio; Bertele', Vittorio

    2006-11-01

    Pharmaceutical innovation is actually poorer than it seems, largely because of "false" innovations. Various factors help create an image of novelty in the pharmaceutical area. These factors act throughout the research and development process and in the post-marketing stages affecting the selection of study hypotheses, the adoption of the appropriate study methodology, and the interpretation and publication of results. Each of these steps may be diverted from the priority objective of patients' interest and shifted towards to the defence of the drugs companies' commercial interests. Regulators, NHS, physicians and patients must be vigilant to recognise and get rid of false innovations which can prevent the use of more effective and safer drugs and waste resources useful for effective treatments in other areas. Rewarding this lack of innovation discourages research for excellence and reduces the competitiveness of the pharmaceutical industry.

  9. False "highlighting" with Wood's lamp.

    PubMed

    Silverberg, Jonathan I; Silverberg, Nanette B

    2014-01-01

    Wood's lamp evaluation is used to diagnose pigmentary disorders. For example, vitiligo typically demonstrates lesional enhancement under Wood's lamp evaluation. Numerous false positive enhancing lesions can be noted in the skin. We describe a 5-year-old Hispanic boy who had painted his face with highlighter, producing enhancing lesions under Wood's lamp. Physicians who use Wood's lamp should be aware that the appearance of markers and highlighter can mimic that of true clinical illnesses.

  10. False positives in imaging genetics.

    PubMed

    Meyer-Lindenberg, Andreas; Nicodemus, Kristin K; Egan, Michael F; Callicott, Joseph H; Mattay, Venkata; Weinberger, Daniel R

    2008-04-01

    Imaging genetics provides an enormous amount of functional-structural data on gene effects in living brain, but the sheer quantity of potential phenotypes raises concerns about false discovery. Here, we provide the first empirical results on false positive rates in imaging genetics. We analyzed 720 frequent coding SNPs without significant association with schizophrenia and a subset of 492 of these without association with cognitive function. Effects on brain structure (using voxel-based morphometry, VBM) and brain function, using two archival imaging tasks, the n-back working memory task and an emotional face matching task, were studied in whole brain and regions of interest and corrected for multiple comparisons using standard neuroimaging procedures. Since these variants are unlikely to impact relevant brain function, positives obtained provide an upper empirical estimate of the false positive association rate. In a separate analysis, we randomly permuted genotype labels across subjects, removing any true genotype-phenotype association in the data, to derive a lower empirical estimate. At a set correction level of 0.05, in each region of interest and data set used, the rate of positive findings was well below 5% (0.2-4.1%). There was no relationship between the region of interest and the false positive rate. Permutation results were in the same range as empirically derived rates. The observed low rates of positives provide empirical evidence that the type I error rate is well controlled by current commonly used correction procedures in imaging genetics, at least in the context of the imaging paradigms we have used. In fact, our observations indicate that these statistical thresholds are conservative.

  11. 7 CFR 58.348 - Plastic cream.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Plastic cream. 58.348 Section 58.348 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Products Bearing Usda Official Identification § 58.348 Plastic cream. The flavor shall be sweet,...

  12. 7 CFR 58.348 - Plastic cream.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Plastic cream. 58.348 Section 58.348 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Products Bearing Usda Official Identification § 58.348 Plastic cream. The flavor shall be sweet,...

  13. 7 CFR 58.348 - Plastic cream.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Plastic cream. 58.348 Section 58.348 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Products Bearing Usda Official Identification § 58.348 Plastic cream. The flavor shall be sweet,...

  14. 7 CFR 58.348 - Plastic cream.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Plastic cream. 58.348 Section 58.348 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Products Bearing Usda Official Identification § 58.348 Plastic cream. The flavor shall be sweet,...

  15. 21 CFR 181.27 - Plasticizers.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Plasticizers. 181.27 Section 181.27 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) PRIOR-SANCTIONED FOOD INGREDIENTS Specific Prior-Sanctioned Food Ingredients § 181.27 Plasticizers. Substances classified...

  16. False advertising in the greenhouse?

    NASA Astrophysics Data System (ADS)

    Banse, K.

    1991-12-01

    Most scientists are convinced of the importance of their own research subjects. Broecker [1991] has deplored the temptation, if not the tendency, to go overboard and exaggerate this importance once funding enters the mind. In particular, he alleges inflated or even false claims by biological (and other) oceanographers regarding the relevance of their research to the "greenhouse effect," caused by the anthropogenic enhancement of the atmospheric CO2 content. He writes [Broecker, 1991, p. 191]: "In my estimation, on any list of subjects requiring intense study with regard to the prediction of the consequences of CO2 buildup in the atmosphere, I would place marine biological cycles near the bottom."

  17. 'Payson' Panorama in False Color

    NASA Technical Reports Server (NTRS)

    2006-01-01

    The panoramic camera aboard NASA's Mars Exploration Rover Opportunity acquired this panorama of the 'Payson' outcrop on the western edge of 'Erebus' Crater during Opportunity's sol 744 (Feb. 26, 2006). From this vicinity at the northern end of the outcrop, layered rocks are observed in the crater wall, which is about 1 meter (3.3 feet) thick. The view also shows rocks disrupted by the crater-forming impact event and subjected to erosion over time.

    To the left of the outcrop, a flat, thin layer of spherule-rich soils overlies more outcrop materials. The rover is currently traveling down this 'road' and observing the approximately 25-meter (82-foot) length of the outcrop prior to departing Erebus crater.

    The panorama camera took 28 separate exposures of this scene, using four different filters. The resulting panorama covers about 90 degrees of terrain around the rover. This false-color rendering was made using the camera's 753-nanometer, 535-nanometer and 423-nanometer filters. Using false color enhances the subtle color differences between layers of rocks and soils in the scene so that scientists can better analyze them. Image-to-image seams have been eliminated from the sky portion of the mosaic to better simulate the vista a person standing on Mars would see.

  18. Cape Verde in False Color

    NASA Technical Reports Server (NTRS)

    2007-01-01

    A promontory nicknamed 'Cape Verde' can be seen jutting out from the walls of Victoria Crater in this false-color picture taken by the panoramic camera on NASA's Mars Exploration Rover Opportunity. The rover took this picture on martian day, or sol, 1329 (Oct. 20, 2007), more than a month after it began descending down the crater walls -- and just 9 sols shy of its second Martian birthday on sol 1338 (Oct. 29, 2007). Opportunity landed on the Red Planet on Jan. 25, 2004. That's nearly four years ago on Earth, but only two on Mars because Mars takes longer to travel around the sun than Earth. One Martian year equals 687 Earth days.

    This view was taken using three panoramic-camera filters, admitting light with wavelengths centered at 750 nanometers (near infrared), 530 nanometers (green) and 430 nanometers (violet).

  19. 23 CFR 635.119 - False statements.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ..., association, firm, or corporation, knowingly makes any false statement, false representation, or false report... submission of plans, maps, specifications, contracts, or costs of construction of any highway or...

  20. 23 CFR 635.119 - False statements.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ..., association, firm, or corporation, knowingly makes any false statement, false representation, or false report... submission of plans, maps, specifications, contracts, or costs of construction of any highway or...

  1. 23 CFR 635.119 - False statements.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ..., association, firm, or corporation, knowingly makes any false statement, false representation, or false report... submission of plans, maps, specifications, contracts, or costs of construction of any highway or...

  2. 49 CFR 192.191 - Design pressure of plastic fittings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Design pressure of plastic fittings. 192.191 Section 192.191 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND... Components § 192.191 Design pressure of plastic fittings. (a) Thermosetting fittings for plastic pipe...

  3. 49 CFR 192.287 - Plastic pipe: Inspection of joints.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Plastic pipe: Inspection of joints. 192.287... Than by Welding § 192.287 Plastic pipe: Inspection of joints. No person may carry out the inspection of joints in plastic pipes required by §§ 192.273(c) and 192.285(b) unless that person has been qualified...

  4. 49 CFR 192.283 - Plastic pipe: Qualifying joining procedures.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Plastic pipe: Qualifying joining procedures. 192... Materials Other Than by Welding § 192.283 Plastic pipe: Qualifying joining procedures. (a) Heat fusion... for making plastic pipe joints by a heat fusion, solvent cement, or adhesive method, the...

  5. 49 CFR 192.123 - Design limitations for plastic pipe.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Design limitations for plastic pipe. 192.123... Design limitations for plastic pipe. (a) Except as provided in paragraph (e) and paragraph (f) of this section, the design pressure may not exceed a gauge pressure of 100 psig (689 kPa) for plastic pipe...

  6. 49 CFR 192.121 - Design of plastic pipe.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Design of plastic pipe. 192.121 Section 192.121... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Pipe Design § 192.121 Design of plastic pipe. Subject to the limitations of § 192.123, the design pressure for plastic pipe is determined by either of...

  7. 49 CFR 192.123 - Design limitations for plastic pipe.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Design limitations for plastic pipe. 192.123... Design limitations for plastic pipe. (a) Except as provided in paragraph (e) and paragraph (f) of this section, the design pressure may not exceed a gauge pressure of 100 psig (689 kPa) for plastic pipe...

  8. 49 CFR 192.311 - Repair of plastic pipe.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Repair of plastic pipe. 192.311 Section 192.311... Lines and Mains § 192.311 Repair of plastic pipe. Each imperfection or damage that would impair the serviceability of plastic pipe must be repaired or removed....

  9. 49 CFR 192.311 - Repair of plastic pipe.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Repair of plastic pipe. 192.311 Section 192.311... Lines and Mains § 192.311 Repair of plastic pipe. Each imperfection or damage that would impair the serviceability of plastic pipe must be repaired or removed....

  10. 49 CFR 192.283 - Plastic pipe: Qualifying joining procedures.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Plastic pipe: Qualifying joining procedures. 192... Materials Other Than by Welding § 192.283 Plastic pipe: Qualifying joining procedures. (a) Heat fusion... for making plastic pipe joints by a heat fusion, solvent cement, or adhesive method, the...

  11. 49 CFR 192.121 - Design of plastic pipe.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Design of plastic pipe. 192.121 Section 192.121... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Pipe Design § 192.121 Design of plastic pipe. Subject to the limitations of § 192.123, the design pressure for plastic pipe is determined by either of...

  12. 49 CFR 192.287 - Plastic pipe: Inspection of joints.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Plastic pipe: Inspection of joints. 192.287... Than by Welding § 192.287 Plastic pipe: Inspection of joints. No person may carry out the inspection of joints in plastic pipes required by §§ 192.273(c) and 192.285(b) unless that person has been qualified...

  13. 49 CFR 192.375 - Service lines: Plastic.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Service lines: Plastic. 192.375 Section 192.375... § 192.375 Service lines: Plastic. (a) Each plastic service line outside a building must be installed... terminate above ground level and outside the building, if— (i) The above ground level part of the...

  14. 49 CFR 192.287 - Plastic pipe: Inspection of joints.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Plastic pipe: Inspection of joints. 192.287... Than by Welding § 192.287 Plastic pipe: Inspection of joints. No person may carry out the inspection of joints in plastic pipes required by §§ 192.273(c) and 192.285(b) unless that person has been qualified...

  15. 49 CFR 192.311 - Repair of plastic pipe.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Repair of plastic pipe. 192.311 Section 192.311... Lines and Mains § 192.311 Repair of plastic pipe. Each imperfection or damage that would impair the serviceability of plastic pipe must be repaired or removed....

  16. 49 CFR 192.121 - Design of plastic pipe.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Design of plastic pipe. 192.121 Section 192.121... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Pipe Design § 192.121 Design of plastic pipe. Subject to the limitations of § 192.123, the design pressure for plastic pipe is determined by either of...

  17. 49 CFR 192.287 - Plastic pipe: Inspection of joints.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Plastic pipe: Inspection of joints. 192.287... Than by Welding § 192.287 Plastic pipe: Inspection of joints. No person may carry out the inspection of joints in plastic pipes required by §§ 192.273(c) and 192.285(b) unless that person has been qualified...

  18. 49 CFR 192.283 - Plastic pipe: Qualifying joining procedures.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Plastic pipe: Qualifying joining procedures. 192... Materials Other Than by Welding § 192.283 Plastic pipe: Qualifying joining procedures. (a) Heat fusion... for making plastic pipe joints by a heat fusion, solvent cement, or adhesive method, the...

  19. 49 CFR 192.191 - Design pressure of plastic fittings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Design pressure of plastic fittings. 192.191... Components § 192.191 Design pressure of plastic fittings. (a) Thermosetting fittings for plastic pipe must conform to ASTM D 2517, (incorporated by reference, see § 192.7). (b) Thermoplastic fittings for...

  20. 49 CFR 192.375 - Service lines: Plastic.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Service lines: Plastic. 192.375 Section 192.375... § 192.375 Service lines: Plastic. (a) Each plastic service line outside a building must be installed... terminate above ground level and outside the building, if— (i) The above ground level part of the...

  1. 49 CFR 192.375 - Service lines: Plastic.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Service lines: Plastic. 192.375 Section 192.375... § 192.375 Service lines: Plastic. (a) Each plastic service line outside a building must be installed... terminate above ground level and outside the building, if— (i) The above ground level part of the...

  2. 49 CFR 192.191 - Design pressure of plastic fittings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Design pressure of plastic fittings. 192.191... Components § 192.191 Design pressure of plastic fittings. (a) Thermosetting fittings for plastic pipe must conform to ASTM D 2517, (incorporated by reference, see § 192.7). (b) Thermoplastic fittings for...

  3. 49 CFR 192.123 - Design limitations for plastic pipe.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Design limitations for plastic pipe. 192.123... Design limitations for plastic pipe. (a) Except as provided in paragraph (e) and paragraph (f) of this section, the design pressure may not exceed a gauge pressure of 100 psig (689 kPa) for plastic pipe...

  4. 49 CFR 192.121 - Design of plastic pipe.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Design of plastic pipe. 192.121 Section 192.121... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Pipe Design § 192.121 Design of plastic pipe. Subject to the limitations of § 192.123, the design pressure for plastic pipe is determined by either of...

  5. 49 CFR 192.123 - Design limitations for plastic pipe.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Design limitations for plastic pipe. 192.123... Design limitations for plastic pipe. (a) Except as provided in paragraph (e) and paragraph (f) of this section, the design pressure may not exceed a gauge pressure of 100 psig (689 kPa) for plastic pipe...

  6. 49 CFR 192.191 - Design pressure of plastic fittings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Design pressure of plastic fittings. 192.191... Components § 192.191 Design pressure of plastic fittings. (a) Thermosetting fittings for plastic pipe must conform to ASTM D 2517, (incorporated by reference, see § 192.7). (b) Thermoplastic fittings for...

  7. 49 CFR 192.311 - Repair of plastic pipe.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Repair of plastic pipe. 192.311 Section 192.311... Lines and Mains § 192.311 Repair of plastic pipe. Each imperfection or damage that would impair the serviceability of plastic pipe must be repaired or removed....

  8. 49 CFR 192.283 - Plastic pipe: Qualifying joining procedures.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Plastic pipe: Qualifying joining procedures. 192... Materials Other Than by Welding § 192.283 Plastic pipe: Qualifying joining procedures. (a) Heat fusion... for making plastic pipe joints by a heat fusion, solvent cement, or adhesive method, the...

  9. 21 CFR 872.3590 - Preformed plastic denture tooth.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Preformed plastic denture tooth. 872.3590 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3590 Preformed plastic denture tooth. (a) Identification. A preformed plastic denture tooth is a prefabricated device, composed of materials such as...

  10. 21 CFR 872.3590 - Preformed plastic denture tooth.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Preformed plastic denture tooth. 872.3590 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3590 Preformed plastic denture tooth. (a) Identification. A preformed plastic denture tooth is a prefabricated device, composed of materials such as...

  11. 21 CFR 872.3590 - Preformed plastic denture tooth.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Preformed plastic denture tooth. 872.3590 Section... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3590 Preformed plastic denture tooth. (a) Identification. A preformed plastic denture tooth is a prefabricated device, composed of materials such as...

  12. 49 CFR 192.375 - Service lines: Plastic.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Customer Meters, Service Regulators, and Service Lines § 192.375 Service lines: Plastic. (a) Each plastic service line outside a building must be installed... 49 Transportation 3 2010-10-01 2010-10-01 false Service lines: Plastic. 192.375 Section...

  13. White Rock in False Color

    NASA Technical Reports Server (NTRS)

    2005-01-01

    [figure removed for brevity, see original site]

    The THEMIS VIS camera is capable of capturing color images of the Martian surface using five different color filters. In this mode of operation, the spatial resolution and coverage of the image must be reduced to accommodate the additional data volume produced from using multiple filters. To make a color image, three of the five filter images (each in grayscale) are selected. Each is contrast enhanced and then converted to a red, green, or blue intensity image. These three images are then combined to produce a full color, single image. Because the THEMIS color filters don't span the full range of colors seen by the human eye, a color THEMIS image does not represent true color. Also, because each single-filter image is contrast enhanced before inclusion in the three-color image, the apparent color variation of the scene is exaggerated. Nevertheless, the color variation that does appear is representative of some change in color, however subtle, in the actual scene. Note that the long edges of THEMIS color images typically contain color artifacts that do not represent surface variation.

    This false color image shows the wind eroded deposit in Pollack Crater called 'White Rock'. This image was collected during the Southern Fall Season.

    Image information: VIS instrument. Latitude -8, Longitude 25.2 East (334.8 West). 0 meter/pixel resolution.

    Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time.

    NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of

  14. Iani Chaos in False Color

    NASA Technical Reports Server (NTRS)

    2005-01-01

    [figure removed for brevity, see original site]

    The THEMIS VIS camera is capable of capturing color images of the Martian surface using five different color filters. In this mode of operation, the spatial resolution and coverage of the image must be reduced to accommodate the additional data volume produced from using multiple filters. To make a color image, three of the five filter images (each in grayscale) are selected. Each is contrast enhanced and then converted to a red, green, or blue intensity image. These three images are then combined to produce a full color, single image. Because the THEMIS color filters don't span the full range of colors seen by the human eye, a color THEMIS image does not represent true color. Also, because each single-filter image is contrast enhanced before inclusion in the three-color image, the apparent color variation of the scene is exaggerated. Nevertheless, the color variation that does appear is representative of some change in color, however subtle, in the actual scene. Note that the long edges of THEMIS color images typically contain color artifacts that do not represent surface variation.

    This false color image of a portion of the Iani Chaos region was collected during the Southern Fall season.

    Image information: VIS instrument. Latitude -2.6 Longitude 342.4 East (17.6 West). 36 meter/pixel resolution.

    Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time.

    NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space Science, Washington, D.C. The

  15. Mimas Showing False Colors #2

    NASA Technical Reports Server (NTRS)

    2005-01-01

    This false color image of Saturn's moon Mimas reveals variation in either the composition or texture across its surface.

    During its approach to Mimas on Aug. 2, 2005, the Cassini spacecraft narrow-angle camera obtained multi-spectral views of the moon from a range of 228,000 kilometers (142,500 miles).

    This image is a color composite of narrow-angle ultraviolet, green, infrared and clear filter images, which have been specially processed to accentuate subtle changes in the spectral properties of Mimas' surface materials. To create this view, three color images (ultraviolet, green and infrared) were combined with a single black and white picture that isolates and maps regional color differences to create the final product.

    Shades of blue and violet in the image at the right are used to identify surface materials that are bluer in color and have a weaker infrared brightness than average Mimas materials, which are represented by green.

    Herschel crater, a 140-kilometer-wide (88-mile) impact feature with a prominent central peak, is visible in the upper right of the image. The unusual bluer materials are seen to broadly surround Herschel crater. However, the bluer material is not uniformly distributed in and around the crater. Instead, it appears to be concentrated on the outside of the crater and more to the west than to the north or south. The origin of the color differences is not yet understood. It may represent ejecta material that was excavated from inside Mimas when the Herschel impact occurred. The bluer color of these materials may be caused by subtle differences in the surface composition or the sizes of grains making up the icy soil.

    This image was obtained when the Cassini spacecraft was above 25 degrees south, 134 degrees west latitude and longitude. The Sun-Mimas-spacecraft angle was 45 degrees and north is at the top.

    The Cassini-Huygens mission is a cooperative project of NASA, the European Space Agency and the Italian

  16. Uninfected anastomotic false aneurysms following arterial reconstruction with prosthetic grafts.

    PubMed

    Read, R C; Thompson, B W

    1975-01-01

    Thirteen men, aged 49 to 76 years, average 60, were treated at the Little Rock, Arkansas Veterans Administration Hospital between January 1, 1969 and January 1, 1974 for 1-3 false aneurysms, a total of 18, following prosthetic arterial grafting. Most (ten patients, 15 aneurysms) had aorto-femoral bifurcation grafts for Leriche syndrome. Dacron prostheses were employed in ten, Teflon in three. The interval between the initial operation and the appearance of the aneurysms averaged six years. The end-to-side femoral anastomosis broke down in all ten patients with Leriche syndrome. Six of the eight unilateral aneurysms were on the right side, two had bilateral aneurysms and one patient had three. Five patients died some months or years after repair from vascular accidents. Three other patients required amputations sometime later because their grafts clotted. Silk sutures were employed in only two patients. Plastic sutures in the others were found to have pulled out of the recipient vessels. The aneurysms were all uninfected and were repaired by local stitching in four and the addition of further plastic grafting in nine. We conclude that false aneurysms occur with plastic sutures and they relate primarily to disruption of the end-to-side femoral artery attachment from the stresses of movement at the hip joint.

  17. Mimas Showing False Colors #1

    NASA Technical Reports Server (NTRS)

    2005-01-01

    False color images of Saturn's moon, Mimas, reveal variation in either the composition or texture across its surface.

    During its approach to Mimas on Aug. 2, 2005, the Cassini spacecraft narrow-angle camera obtained multi-spectral views of the moon from a range of 228,000 kilometers (142,500 miles).

    The image at the left is a narrow angle clear-filter image, which was separately processed to enhance the contrast in brightness and sharpness of visible features. The image at the right is a color composite of narrow-angle ultraviolet, green, infrared and clear filter images, which have been specially processed to accentuate subtle changes in the spectral properties of Mimas' surface materials. To create this view, three color images (ultraviolet, green and infrared) were combined into a single black and white picture that isolates and maps regional color differences. This 'color map' was then superimposed over the clear-filter image at the left.

    The combination of color map and brightness image shows how the color differences across the Mimas surface materials are tied to geological features. Shades of blue and violet in the image at the right are used to identify surface materials that are bluer in color and have a weaker infrared brightness than average Mimas materials, which are represented by green.

    Herschel crater, a 140-kilometer-wide (88-mile) impact feature with a prominent central peak, is visible in the upper right of each image. The unusual bluer materials are seen to broadly surround Herschel crater. However, the bluer material is not uniformly distributed in and around the crater. Instead, it appears to be concentrated on the outside of the crater and more to the west than to the north or south. The origin of the color differences is not yet understood. It may represent ejecta material that was excavated from inside Mimas when the Herschel impact occurred. The bluer color of these materials may be caused by subtle differences in

  18. 33 CFR 183.516 - Cellular plastic used to encase fuel tanks.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Cellular plastic used to encase....516 Cellular plastic used to encase fuel tanks. (a) Cellular plastic used to encase metallic fuel...-polyurethane cellular plastic used to encase metallic fuel tanks must have a compressive strength of at...

  19. 21 CFR 310.509 - Parenteral drug products in plastic containers.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 5 2011-04-01 2011-04-01 false Parenteral drug products in plastic containers... Parenteral drug products in plastic containers. (a) Any parenteral drug product packaged in a plastic... parenteral drug product for intravenous use in humans that is packaged in a plastic immediate container on...

  20. 21 CFR 310.509 - Parenteral drug products in plastic containers.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 5 2014-04-01 2014-04-01 false Parenteral drug products in plastic containers... Parenteral drug products in plastic containers. (a) Any parenteral drug product packaged in a plastic... parenteral drug product for intravenous use in humans that is packaged in a plastic immediate container on...

  1. 21 CFR 310.509 - Parenteral drug products in plastic containers.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 5 2013-04-01 2013-04-01 false Parenteral drug products in plastic containers... Parenteral drug products in plastic containers. (a) Any parenteral drug product packaged in a plastic... parenteral drug product for intravenous use in humans that is packaged in a plastic immediate container on...

  2. 21 CFR 310.509 - Parenteral drug products in plastic containers.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 5 2012-04-01 2012-04-01 false Parenteral drug products in plastic containers... Parenteral drug products in plastic containers. (a) Any parenteral drug product packaged in a plastic... parenteral drug product for intravenous use in humans that is packaged in a plastic immediate container on...

  3. 46 CFR 160.010-5 - Buoyant apparatus with plastic foam buoyancy.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 6 2014-10-01 2014-10-01 false Buoyant apparatus with plastic foam buoyancy. 160.010-5... Vessels § 160.010-5 Buoyant apparatus with plastic foam buoyancy. (a) Buoyant apparatus with plastic foam buoyancy must have a plastic foam body with an external protective covering. The body may be reinforced...

  4. 33 CFR 183.516 - Cellular plastic used to encase fuel tanks.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Cellular plastic used to encase....516 Cellular plastic used to encase fuel tanks. (a) Cellular plastic used to encase metallic fuel...-polyurethane cellular plastic used to encase metallic fuel tanks must have a compressive strength of at...

  5. 33 CFR 183.516 - Cellular plastic used to encase fuel tanks.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false Cellular plastic used to encase....516 Cellular plastic used to encase fuel tanks. (a) Cellular plastic used to encase metallic fuel...-polyurethane cellular plastic used to encase metallic fuel tanks must have a compressive strength of at...

  6. 33 CFR 183.516 - Cellular plastic used to encase fuel tanks.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Cellular plastic used to encase....516 Cellular plastic used to encase fuel tanks. (a) Cellular plastic used to encase metallic fuel...-polyurethane cellular plastic used to encase metallic fuel tanks must have a compressive strength of at...

  7. 46 CFR 160.010-5 - Buoyant apparatus with plastic foam buoyancy.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 6 2013-10-01 2013-10-01 false Buoyant apparatus with plastic foam buoyancy. 160.010-5... Vessels § 160.010-5 Buoyant apparatus with plastic foam buoyancy. (a) Buoyant apparatus with plastic foam buoyancy must have a plastic foam body with an external protective covering. The body may be reinforced...

  8. 33 CFR 183.516 - Cellular plastic used to encase fuel tanks.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false Cellular plastic used to encase....516 Cellular plastic used to encase fuel tanks. (a) Cellular plastic used to encase metallic fuel...-polyurethane cellular plastic used to encase metallic fuel tanks must have a compressive strength of at...

  9. 19 CFR 111.32 - False information.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false False information. 111.32 Section 111.32 Customs... CUSTOMS BROKERS Duties and Responsibilities of Customs Brokers § 111.32 False information. A broker must... procure the giving of, any false or misleading information or testimony in any matter pending before...

  10. 49 CFR 195.452 - Pipeline integrity management in high consequence areas.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Pipeline integrity management in high consequence...) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Operation and Maintenance Pipeline...

  11. 46 CFR 308.305 - [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 8 2012-10-01 2012-10-01 false 308.305 Section 308.305 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE Second Seamen's War Risk Insurance § 308.305...

  12. 46 CFR 308.301 - [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 8 2012-10-01 2012-10-01 false 308.301 Section 308.301 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION EMERGENCY OPERATIONS WAR RISK INSURANCE Second Seamen's War Risk Insurance § 308.301...

  13. 47 CFR 27.59 - [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 2 2012-10-01 2012-10-01 false 27.59 Section 27.59 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES Technical Standards § 27.59...

  14. 47 CFR 27.15 - Geographic partitioning and spectrum disaggregation.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 2 2012-10-01 2012-10-01 false Geographic partitioning and spectrum disaggregation. 27.15 Section 27.15 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES Applications and Licenses §...

  15. 49 CFR 193.2015 - [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false 193.2015 Section 193.2015 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION... STANDARDS General § 193.2015...

  16. 48 CFR 225.7009 - Restriction on ball and roller bearings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Restriction on ball and roller bearings. 225.7009 Section 225.7009 Federal Acquisition Regulations System DEFENSE ACQUISITION... roller bearings....

  17. 49 CFR 236.764 - Locking, lever operated.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Locking, lever operated. 236.764 Section 236.764... Locking, lever operated. The mechanical locking of an interlocking machine which is actuated by means of the lever....

  18. 47 CFR 10.310 - Federal alert gateway. [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 1 2012-10-01 2012-10-01 false Federal alert gateway. 10.310 Section 10.310 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL COMMERCIAL MOBILE ALERT SYSTEM System Architecture § 10.310 Federal alert gateway....

  19. 47 CFR 10.300 - Alert aggregator. [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 1 2012-10-01 2012-10-01 false Alert aggregator. 10.300 Section 10.300 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL COMMERCIAL MOBILE ALERT SYSTEM System Architecture § 10.300 Alert aggregator....

  20. 43 CFR 2650.3 - Lawful entries, lawful settlements, and mining claims.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Lawful entries, lawful settlements, and mining claims. 2650.3 Section 2650.3 Public Lands: Interior Regulations Relating to Public Lands... mining claims....

  1. 48 CFR 1511.011-79 - Information resources management.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false Information resources... AGENCY ACQUISITION PLANNING DESCRIBING AGENCY NEEDS 1511.011-79 Information resources management. The... Resource Management, in all solicitations and contracts....

  2. 48 CFR Appendix E to Chapter 7 - [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false E Appendix E to Chapter 7 Federal Acquisition Regulations System AGENCY FOR INTERNATIONAL DEVELOPMENT Appendix E to Chapter 7...

  3. 49 CFR 374.315 - Transportation of passengers with disabilities.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... by the Secretary of Transportation (49 CFR parts 27, 37, and 38) and the Attorney General (28 CFR... Compliance Board (36 CFR part 1191). ... 49 Transportation 5 2012-10-01 2012-10-01 false Transportation of passengers with...

  4. 47 CFR 1.1117 - Adjustments to charges.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 1 2012-10-01 2012-10-01 false Adjustments to charges. 1.1117 Section 1.1117 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL PRACTICE AND PROCEDURE Grants by Random Selection... errors made during an adjustment cycle....

  5. 47 CFR 74.643 - Interference to geostationary-satellites.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 4 2012-10-01 2012-10-01 false Interference to geostationary-satellites. 74... Television Broadcast Auxiliary Stations § 74.643 Interference to geostationary-satellites. Applicants and... geostationary-satellites....

  6. 47 CFR 25.219 - [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 2 2012-10-01 2012-10-01 false 25.219 Section 25.219 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Technical Standards § 25.219...

  7. 47 CFR 80.333 - Stations in the maritime mobile-satellite service.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 5 2012-10-01 2012-10-01 false Stations in the maritime mobile-satellite..., Alarm, Urgency and Safety Procedures § 80.333 Stations in the maritime mobile-satellite service. The...-satellite service....

  8. 48 CFR 27.204 - Patented technology under trade agreements.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Patented technology under trade agreements. 27.204 Section 27.204 Federal Acquisition Regulations System FEDERAL ACQUISITION... Patented technology under trade agreements....

  9. 49 CFR 601.40 - Applicability.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 7 2012-10-01 2012-10-01 false Applicability. 601.40 Section 601.40 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ORGANIZATION, FUNCTIONS, AND PROCEDURES Emergency Procedures for...

  10. 49 CFR Appendix B to Part 210 - Switcher Locomotive Enforcement Policy

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Switcher Locomotive Enforcement Policy B Appendix B to Part 210 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD NOISE EMISSION COMPLIANCE REGULATIONS...

  11. 48 CFR 970.2201-2 - Overtime management.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Overtime management. 970... SUPPLEMENTARY REGULATIONS DOE MANAGEMENT AND OPERATING CONTRACTS Application of Labor Policies 970.2201-2 Overtime management....

  12. 48 CFR 970.3770 - Facilities management.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Facilities management. 970... REGULATIONS DOE MANAGEMENT AND OPERATING CONTRACTS Facilities Management Contracting 970.3770 Facilities management....

  13. 49 CFR 236.741 - Distance, stopping.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Distance, stopping. 236.741 Section 236.741... Distance, stopping. The maximum distance on any portion of any railroad which any train operating on such... stop....

  14. 48 CFR 245.201-73 - Security classification.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Security classification... Procedures 245.201-73 Security classification. Follow the procedures at PGI 245.201-73 for security classification....

  15. 48 CFR 215.404 - Proposal analysis.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Proposal analysis. 215.404 Section 215.404 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT... Proposal analysis....

  16. 47 CFR 4.1 - Scope, basis and purpose.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 1 2012-10-01 2012-10-01 false Scope, basis and purpose. 4.1 Section 4.1... and purpose. In this part, the Federal Communications Commission is setting forth requirements... communications infrastructures....

  17. 49 CFR 229.303 - Applicability.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Applicability. 229.303 Section 229.303 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD LOCOMOTIVE SAFETY STANDARDS Locomotive Electronics §...

  18. 47 CFR 73.6023 - Distributed transmission systems.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 4 2012-10-01 2012-10-01 false Distributed transmission systems. 73.6023... RADIO BROADCAST SERVICES Class A Television Broadcast Stations § 73.6023 Distributed transmission... distributed transmission system....

  19. 49 CFR 520.2 - Policy.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 6 2012-10-01 2012-10-01 false Policy. 520.2 Section 520.2 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT... affect the quality of the human environment....

  20. 48 CFR 947.7000 - [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false 947.7000 Section 947.7000 Federal Acquisition Regulations System DEPARTMENT OF ENERGY CONTRACT MANAGEMENT TRANSPORTATION Foreign Travel 947.7000...

  1. 48 CFR 1523.303 - Contract clause.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false Contract clause. 1523.303 Section 1523.303 Federal Acquisition Regulations System ENVIRONMENTAL PROTECTION AGENCY SOCIOECONOMIC... Material Safety Data 1523.303 Contract clause....

  2. 49 CFR 178.360 - Specification 2R; inside containment vessel.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Specification 2R; inside containment vessel. 178.360 Section 178.360 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE... Specification 2R; inside containment vessel....

  3. 48 CFR 22.809 - Enforcement.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... the Department of Justice or to the Equal Employment Opportunity Commission (EEOC) for the institution of appropriate civil or criminal proceedings. ... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Enforcement....

  4. 48 CFR 53.236 - Construction and architect-engineer contracts.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 2 2012-10-01 2012-10-01 false Construction and architect-engineer contracts. 53.236 Section 53.236 Federal Acquisition Regulations System FEDERAL ACQUISITION...-engineer contracts....

  5. 48 CFR 27.201 - Patent and copyright infringement liability.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Patent and copyright... REGULATION GENERAL CONTRACTING REQUIREMENTS PATENTS, DATA, AND COPYRIGHTS Patents and Copyrights 27.201 Patent and copyright infringement liability....

  6. 48 CFR 1327.201 - Patent and copyright infringement liability.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Patent and copyright... GENERAL CONTRACTING REQUIREMENTS PATENTS, DATA, AND COPYRIGHTS Patents and Copyrights 1327.201 Patent and copyright infringement liability....

  7. 48 CFR 1427.201 - Patent and copyright infringement liability.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Patent and copyright... INTERIOR GENERAL CONTRACTING REQUIREMENTS PATENTS, DATA, AND COPYRIGHTS Patents and Copyrights 1427.201 Patent and copyright infringement liability....

  8. 48 CFR 1327.305 - Administration of patent rights clauses.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Administration of patent... GENERAL CONTRACTING REQUIREMENTS PATENTS, DATA, AND COPYRIGHTS Patent Rights Under Government Contracts 1327.305 Administration of patent rights clauses....

  9. 48 CFR 2427.305 - Administration of patent rights clauses.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false Administration of patent... AND URBAN DEVELOPMENT SOCIOECONOMIC PROGRAMS PATENTS, DATA, AND COPYRIGHTS Patent Rights Under Government Contracts 2427.305 Administration of patent rights clauses....

  10. 48 CFR 1227.305 - Administration of patent rights clauses.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Administration of patent... TRANSPORTATION GENERAL CONTRACTING REQUIREMENTS PATENTS, DATA, AND COPYRIGHTS Patent Rights Under Government Contracts 1227.305 Administration of patent rights clauses....

  11. 48 CFR 27.305 - Administration of patent rights clauses.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Administration of patent... REGULATION GENERAL CONTRACTING REQUIREMENTS PATENTS, DATA, AND COPYRIGHTS Patent Rights under Government Contracts 27.305 Administration of patent rights clauses....

  12. 50 CFR 38.5 - Emergency authority.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... NATIONAL WILDLIFE REFUGE SYSTEM MIDWAY ATOLL NATIONAL WILDLIFE REFUGE Executive Authority; Authorized... Midway Atoll National Wildlife Refuge. ... 50 Wildlife and Fisheries 9 2012-10-01 2012-10-01 false Emergency authority. 38.5 Section...

  13. 47 CFR 5.81 - Discontinuance of station operation.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 1 2012-10-01 2012-10-01 false Discontinuance of station operation. 5.81 Section 5.81 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL EXPERIMENTAL RADIO SERVICE (OTHER... Commission's Office of Engineering and Technology for cancellation....

  14. 48 CFR 225.7005 - Restriction on certain chemical weapons antidote.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Restriction on certain chemical weapons antidote. 225.7005 Section 225.7005 Federal Acquisition Regulations System DEFENSE... on certain chemical weapons antidote....

  15. 46 CFR 8.320 - Classification society authorization to issue international certificates.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 1 2012-10-01 2012-10-01 false Classification society authorization to issue... Classification society authorization to issue international certificates. (a) The Commandant may authorize a recognized classification society to issue certain international convention certificates. Authorization...

  16. 48 CFR 970.3002 - CAS program requirements.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false CAS program requirements. 970.3002 Section 970.3002 Federal Acquisition Regulations System DEPARTMENT OF ENERGY AGENCY....3002 CAS program requirements....

  17. 48 CFR 970.0470 - Department of Energy Directives.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Department of Energy Directives. 970.0470 Section 970.0470 Federal Acquisition Regulations System DEPARTMENT OF ENERGY AGENCY... Energy Directives....

  18. 49 CFR 178.33a - Specification 2Q; inner nonrefillable metal receptacles.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Specification 2Q; inner nonrefillable metal receptacles. 178.33a Section 178.33a Transportation Other Regulations Relating to Transportation (Continued... nonrefillable metal receptacles....

  19. 49 CFR 178.33 - Specification 2P; inner nonrefillable metal receptacles.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Specification 2P; inner nonrefillable metal receptacles. 178.33 Section 178.33 Transportation Other Regulations Relating to Transportation (Continued... nonrefillable metal receptacles....

  20. 48 CFR 225.7003 - Restrictions on acquisition of specialty metals.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Restrictions on acquisition of specialty metals. 225.7003 Section 225.7003 Federal Acquisition Regulations System DEFENSE... Restrictions on acquisition of specialty metals....

  1. 47 CFR 73.881 - Equal employment opportunities.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 4 2012-10-01 2012-10-01 false Equal employment opportunities. 73.881 Section 73.881 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES RADIO... origin, or sex....

  2. 48 CFR 232.502 - Preaward matters.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Preaward matters. 232.502 Section 232.502 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT....502 Preaward matters....

  3. 48 CFR 232.503 - Postaward matters.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Postaward matters. 232.503 Section 232.503 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT....503 Postaward matters....

  4. 43 CFR 3120.5 - Competitive sale.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Competitive sale. 3120.5 Section 3120.5 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT... Competitive sale....

  5. 48 CFR 53.301-1423 - Inventory Verification Survey.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 2 2012-10-01 2012-10-01 false Inventory Verification Survey. 53.301-1423 Section 53.301-1423 Federal Acquisition Regulations System FEDERAL ACQUISITION... Survey. ER05AP04.000...

  6. 48 CFR 1552.228-70 - Insurance liability to third persons.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false Insurance liability to third persons. 1552.228-70 Section 1552.228-70 Federal Acquisition Regulations System ENVIRONMENTAL... cost accounting practices. (End of clause)...

  7. 43 CFR 2912.1 - Nature of interest.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Nature of interest. 2912.1 Section 2912.1 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT... Nature of interest....

  8. 46 CFR 176.814 - Steering systems.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 7 2012-10-01 2012-10-01 false Steering systems. 176.814 Section 176.814 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS... hydraulic pumps secured....

  9. 48 CFR 922.804 - Affirmative action programs.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Affirmative action programs. 922.804 Section 922.804 Federal Acquisition Regulations System DEPARTMENT OF ENERGY SOCIOECONOMIC... Affirmative action programs....

  10. 48 CFR 1422.804 - Affirmative action programs.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Affirmative action programs. 1422.804 Section 1422.804 Federal Acquisition Regulations System DEPARTMENT OF THE INTERIOR....804 Affirmative action programs....

  11. 48 CFR 22.804 - Affirmative action programs.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Affirmative action programs. 22.804 Section 22.804 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION... Affirmative action programs....

  12. 48 CFR 422.804 - Affirmative action programs.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 4 2012-10-01 2012-10-01 false Affirmative action programs. 422.804 Section 422.804 Federal Acquisition Regulations System DEPARTMENT OF AGRICULTURE... Affirmative action programs....

  13. 48 CFR 522.804 - Affirmative action programs.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 4 2012-10-01 2012-10-01 false Affirmative action programs. 522.804 Section 522.804 Federal Acquisition Regulations System GENERAL SERVICES ADMINISTRATION... Affirmative action programs....

  14. 48 CFR 1522.804 - Affirmative action programs.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false Affirmative action programs. 1522.804 Section 1522.804 Federal Acquisition Regulations System ENVIRONMENTAL PROTECTION AGENCY....804 Affirmative action programs....

  15. 48 CFR 3032.006 - Reduction or suspension of contract payments upon finding of fraud.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 7 2012-10-01 2012-10-01 false Reduction or suspension of contract payments upon finding of fraud. 3032.006 Section 3032.006 Federal Acquisition Regulations System... finding of fraud....

  16. 47 CFR 76.227 - [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 4 2012-10-01 2012-10-01 false 76.227 Section 76.227 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES MULTICHANNEL VIDEO AND CABLE TELEVISION SERVICE Cablecasting § 76.227...

  17. 48 CFR 3403.101-3 - Agency regulations.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 34 CFR part 73, Standards of Conduct. ... 48 Federal Acquisition Regulations System 7 2012-10-01 2012-10-01 false Agency regulations. 3403.101-3 Section 3403.101-3 Federal Acquisition Regulations System DEPARTMENT OF EDUCATION...

  18. 49 CFR 655.62 - Referral, evaluation, and treatment.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 7 2012-10-01 2012-10-01 false Referral, evaluation, and treatment. 655.62... OPERATIONS Consequences § 655.62 Referral, evaluation, and treatment. If a covered employee has a verified... and treatment programs....

  19. 48 CFR 222.101 - Labor relations.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... OF DEFENSE SOCIOECONOMIC PROGRAMS APPLICATION OF LABOR LAWS TO GOVERNMENT ACQUISITIONS Basic Labor Policies 222.101 Labor relations. ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Labor relations....

  20. 48 CFR 22.102 - Federal and State labor requirements.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... SOCIOECONOMIC PROGRAMS APPLICATION OF LABOR LAWS TO GOVERNMENT ACQUISITIONS Basic Labor Policies 22.102 Federal and State labor requirements. ... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Federal and State...

  1. 48 CFR 25.703 - Prohibition on contracting with entities that engage in certain activities relating to Iran.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Prohibition on contracting with entities that engage in certain activities relating to Iran. 25.703 Section 25.703 Federal... to Iran....

  2. 48 CFR 1215.606-2 - Evaluation.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... of (FAR) 48 CFR 15.607. ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Evaluation. 1215.606-2... AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Unsolicited Proposals 1215.606-2 Evaluation....

  3. 48 CFR 1515.305 - Proposal evaluation.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false Proposal evaluation. 1515.305 Section 1515.305 Federal Acquisition Regulations System ENVIRONMENTAL PROTECTION AGENCY... evaluation....

  4. 48 CFR 415.305 - Proposal evaluation.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 4 2012-10-01 2012-10-01 false Proposal evaluation. 415... METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Source Selection 415.305 Proposal evaluation. HCAs... of the technical evaluation team....

  5. 48 CFR 970.5001 - Residual powers.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Residual powers. 970.5001 Section 970.5001 Federal Acquisition Regulations System DEPARTMENT OF ENERGY AGENCY SUPPLEMENTARY....5001 Residual powers....

  6. 48 CFR 1850.104 - Residual powers.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false Residual powers. 1850.104 Section 1850.104 Federal Acquisition Regulations System NATIONAL AERONAUTICS AND SPACE ADMINISTRATION... 1850.104 Residual powers....

  7. 48 CFR 250.104 - Residual powers.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Residual powers. 250.104 Section 250.104 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT... Contractual Actions 250.104 Residual powers....

  8. 48 CFR 1815.609 - Limited use of data.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false Limited use of data. 1815.609 Section 1815.609 Federal Acquisition Regulations System NATIONAL AERONAUTICS AND SPACE... Limited use of data....

  9. 48 CFR 246.470 - Government contract quality assurance actions.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Government contract... ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CONTRACT MANAGEMENT QUALITY ASSURANCE Government Contract Quality Assurance 246.470 Government contract quality assurance actions....

  10. 42 CFR 457.800 - Basis, scope, and applicability.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... SERVICES (CONTINUED) STATE CHILDREN'S HEALTH INSURANCE PROGRAMS (SCHIPs) ALLOTMENTS AND GRANTS TO STATES... apply to separate child health programs. ... 42 Public Health 4 2012-10-01 2012-10-01 false Basis, scope, and applicability. 457.800...

  11. 47 CFR 2.936 - FCC inspection.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 1 2012-10-01 2012-10-01 false FCC inspection. 2.936 Section 2.936 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL... manufacturing plant and facilities....

  12. 49 CFR 220.21 - Railroad operating rules; radio communications; recordkeeping.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... meaning given these terms in 49 CFR Part 1201. ... 49 Transportation 4 2012-10-01 2012-10-01 false Railroad operating rules; radio communications...) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD COMMUNICATIONS Radio and...

  13. 48 CFR 225.7017 - Utilization of domestic photovoltaic devices.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Utilization of domestic photovoltaic devices. 225.7017 Section 225.7017 Federal Acquisition Regulations System DEFENSE ACQUISITION... photovoltaic devices....

  14. 48 CFR 1804.470 - Security requirements for unclassified information technology (IT) resources.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false Security requirements for unclassified information technology (IT) resources. 1804.470 Section 1804.470 Federal Acquisition Regulations... (IT) resources....

  15. 47 CFR 25.402 - [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 2 2012-10-01 2012-10-01 false 25.402 Section 25.402 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Competitive Bidding Procedures for DARS § 25.402...

  16. 49 CFR 178.33b - Specification 2S; inner nonrefillable plastic receptacles.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Specification 2S; inner nonrefillable plastic receptacles. 178.33b Section 178.33b Transportation Other Regulations Relating to Transportation (Continued... nonrefillable plastic receptacles....

  17. 49 CFR 178.33b - Specification 2S; inner nonrefillable plastic receptacles.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Specification 2S; inner nonrefillable plastic receptacles. 178.33b Section 178.33b Transportation Other Regulations Relating to Transportation (Continued... nonrefillable plastic receptacles....

  18. 49 CFR 178.33b - Specification 2S; inner nonrefillable plastic receptacles.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Specification 2S; inner nonrefillable plastic receptacles. 178.33b Section 178.33b Transportation Other Regulations Relating to Transportation (Continued... nonrefillable plastic receptacles....

  19. 49 CFR 178.33b - Specification 2S; inner nonrefillable plastic receptacles.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Specification 2S; inner nonrefillable plastic receptacles. 178.33b Section 178.33b Transportation Other Regulations Relating to Transportation PIPELINE AND... nonrefillable plastic receptacles....

  20. An Association Account of False Belief Understanding

    ERIC Educational Resources Information Center

    De Bruin, L. C.; Newen, A.

    2012-01-01

    The elicited-response false belief task has traditionally been considered as reliably indicating that children acquire an understanding of false belief around 4 years of age. However, recent investigations using spontaneous-response tasks suggest that false belief understanding emerges much earlier. This leads to a developmental paradox: if young…

  1. 30 CFR 281.5 - False statements.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false False statements. 281.5 Section 281.5 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE LEASING OF MINERALS OTHER THAN OIL, GAS, AND SULPHUR IN THE OUTER CONTINENTAL SHELF General § 281.5 False statements. Under...

  2. 43 CFR 3000.2 - False statements.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MINERALS MANAGEMENT: GENERAL General § 3000.2 False statements. Under the provisions of 18 U.S.C. 1001, it is a crime punishable by 5 years imprisonment or a... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false False statements. 3000.2 Section...

  3. Attitude Importance and the False Consensus Effect.

    ERIC Educational Resources Information Center

    Fabrigar, Leandre R.; Krosnick, Jon A.

    1995-01-01

    Explores the possibility that importance may regulate the magnitude of the false consensus effect. Analysis revealed a strong false consensus effect but no reliable relation between its magnitude and attitude importance. Results contradict assumptions that the false consensus effect arises from attitudes that directly or indirectly influence…

  4. 20 CFR 356.3 - False claims.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 20 Employees' Benefits 1 2012-04-01 2012-04-01 false False claims. 356.3 Section 356.3 Employees' Benefits RAILROAD RETIREMENT BOARD ADMINISTRATIVE REMEDIES FOR FRAUDULENT CLAIMS OR STATEMENTS CIVIL MONETARY PENALTY INFLATION ADJUSTMENT § 356.3 False claims. In the case of penalties assessed under 31...

  5. 20 CFR 356.3 - False claims.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false False claims. 356.3 Section 356.3 Employees' Benefits RAILROAD RETIREMENT BOARD ADMINISTRATIVE REMEDIES FOR FRAUDULENT CLAIMS OR STATEMENTS CIVIL MONETARY PENALTY INFLATION ADJUSTMENT § 356.3 False claims. In the case of penalties assessed under 31...

  6. 20 CFR 356.3 - False claims.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 20 Employees' Benefits 1 2011-04-01 2011-04-01 false False claims. 356.3 Section 356.3 Employees' Benefits RAILROAD RETIREMENT BOARD ADMINISTRATIVE REMEDIES FOR FRAUDULENT CLAIMS OR STATEMENTS CIVIL MONETARY PENALTY INFLATION ADJUSTMENT § 356.3 False claims. In the case of penalties assessed under 31...

  7. Periodontal Plastic Surgery

    MedlinePlus

    ... Dental Implants Dentures Direct Bonding Implants versus Bridges Orthodontics and Aligners Periodontal Plastic Surgery Porcelain Crowns Porcelain ... Dental Implants Dentures Direct Bonding Implants versus Bridges Orthodontics and Aligners Periodontal Plastic Surgery Porcelain Crowns Porcelain ...

  8. Plasticity and Geotechnics

    NASA Astrophysics Data System (ADS)

    Yu, Hai-Sui

    Plasticity and Geotechnics is the first attempt to summarize and present, in one volume, the major developments achieved to date in the field of plasticity theory for geotechnical materials and its applications to geotechnical analysis and design.

  9. Plastic Surgery for Teenagers

    MedlinePlus

    ... or severe acne and scarring. Teens frequently gain self-esteem and confidence when their physical problems are corrected. ... art as a helpful index of anxiety and self-esteem with plastic surgery. Plastic and Reconstructive Surgery 2002. ...

  10. Plastic casting resin poisoning

    MedlinePlus

    Epoxy poisoning; Resin poisoning ... Epoxy and resin can be poisonous if they are swallowed or their fumes are breathed in. ... Plastic casting resins are found in various plastic casting resin products.

  11. Ear Plastic Surgery

    MedlinePlus

    ... Meeting Calendar Find an ENT Doctor Near You Ear Plastic Surgery Ear Plastic Surgery Patient Health Information ... they may improve appearance and self-confidence. Can Ear Deformities Be Corrected? Formation of the ear during ...

  12. Plastic encapsulated parts

    SciTech Connect

    Castillo, T.

    1994-10-01

    Plastic semiconductor packages were characterized as possible alternatives for canned devices, which are susceptible to internal shorts caused by conductive particles. Highly accelerated stress testing (HAST) as well as electrical and mechanical testing were conducted on plastic technology devices.

  13. Tomorrow's Plastic World

    ERIC Educational Resources Information Center

    Macdonald, Averil

    2005-01-01

    Far from being just cheap packaging materials, plastics may be the materials of tomorrow. Plastic can conduct electricity, and this opens up a host of high-tech possibilities in the home and in energy generation. These possibilities are discussed here along with how plastic can be recycled and perhaps even grown.

  14. Processing of plastics

    PubMed Central

    Spaak, Albert

    1975-01-01

    An overview is given of the processing of plastic materials from the handling of polymers in the pellet and powder form to manufacturing of a plastic fabricated product. Various types of equipment used and melt processing ranges of various polymer formulations to make the myriad of plastic products that are commercially available are discussed. PMID:1175556

  15. Plastics in Building.

    ERIC Educational Resources Information Center

    Skeist, Irving, Ed.

    The evaluation and use of plastics in the construction industry are explained. The contributors offer extensive, timely, and thoroughly researched data on the chemistry, properties, functions, engineering behavior, and specific applications of plastics to building requirements. The major subjects discussed in depth are--(1) the role of plastics in…

  16. An association account of false belief understanding.

    PubMed

    De Bruin, L C; Newen, A

    2012-05-01

    The elicited-response false belief task has traditionally been considered as reliably indicating that children acquire an understanding of false belief around 4 years of age. However, recent investigations using spontaneous-response tasks suggest that false belief understanding emerges much earlier. This leads to a developmental paradox: if young infants already understand false belief, then why do they fail the elicited-response false belief task? We postulate two systems to account for the development of false belief understanding: an association module, which provides infants with the capacity to register congruent associations between agents and objects, and an operating system, which allows them to transform these associations into incongruent associations through a process of inhibition, selection and representation. The interaction between the association module and the operating system enables infants to register increasingly complex associations on the basis of another agent's movements, visual perspective and propositional attitudes. This allows us account for the full range of findings on false belief understanding.

  17. Biodegradability of Plastics

    PubMed Central

    Tokiwa, Yutaka; Calabia, Buenaventurada P.; Ugwu, Charles U.; Aiba, Seiichi

    2009-01-01

    Plastic is a broad name given to different polymers with high molecular weight, which can be degraded by various processes. However, considering their abundance in the environment and their specificity in attacking plastics, biodegradation of plastics by microorganisms and enzymes seems to be the most effective process. When plastics are used as substrates for microorganisms, evaluation of their biodegradability should not only be based on their chemical structure, but also on their physical properties (melting point, glass transition temperature, crystallinity, storage modulus etc.). In this review, microbial and enzymatic biodegradation of plastics and some factors that affect their biodegradability are discussed. PMID:19865515

  18. Biodegradability of plastics.

    PubMed

    Tokiwa, Yutaka; Calabia, Buenaventurada P; Ugwu, Charles U; Aiba, Seiichi

    2009-08-26

    Plastic is a broad name given to different polymers with high molecular weight, which can be degraded by various processes. However, considering their abundance in the environment and their specificity in attacking plastics, biodegradation of plastics by microorganisms and enzymes seems to be the most effective process. When plastics are used as substrates for microorganisms, evaluation of their biodegradability should not only be based on their chemical structure, but also on their physical properties (melting point, glass transition temperature, crystallinity, storage modulus etc.). In this review, microbial and enzymatic biodegradation of plastics and some factors that affect their biodegradability are discussed.

  19. 19 CFR 11.13 - False designations of origin and false descriptions; false marking of articles of gold or silver.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... descriptions; false marking of articles of gold or silver. 11.13 Section 11.13 Customs Duties U.S. CUSTOMS AND... gold or silver. (a) Articles which bear, or the containers which bear, false designations of origin, or.... 1405q, and shall be detained. (b) Articles made in whole or in part of gold or silver or alloys...

  20. 19 CFR 11.13 - False designations of origin and false descriptions; false marking of articles of gold or silver.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... descriptions; false marking of articles of gold or silver. 11.13 Section 11.13 Customs Duties U.S. CUSTOMS AND... gold or silver. (a) Articles which bear, or the containers which bear, false designations of origin, or.... 1405q, and shall be detained. (b) Articles made in whole or in part of gold or silver or alloys...

  1. 19 CFR 11.13 - False designations of origin and false descriptions; false marking of articles of gold or silver.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... descriptions; false marking of articles of gold or silver. 11.13 Section 11.13 Customs Duties U.S. CUSTOMS AND... gold or silver. (a) Articles which bear, or the containers which bear, false designations of origin, or.... 1405q, and shall be detained. (b) Articles made in whole or in part of gold or silver or alloys...

  2. 19 CFR 11.13 - False designations of origin and false descriptions; false marking of articles of gold or silver.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... descriptions; false marking of articles of gold or silver. 11.13 Section 11.13 Customs Duties U.S. CUSTOMS AND... gold or silver. (a) Articles which bear, or the containers which bear, false designations of origin, or.... 1405q, and shall be detained. (b) Articles made in whole or in part of gold or silver or alloys...

  3. 19 CFR 11.13 - False designations of origin and false descriptions; false marking of articles of gold or silver.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... descriptions; false marking of articles of gold or silver. 11.13 Section 11.13 Customs Duties U.S. CUSTOMS AND... gold or silver. (a) Articles which bear, or the containers which bear, false designations of origin, or.... 1405q, and shall be detained. (b) Articles made in whole or in part of gold or silver or alloys...

  4. False confessions: causes, consequences, and implications.

    PubMed

    Leo, Richard A

    2009-01-01

    In the past two decades, hundreds of convicted prisoners have been exonerated by DNA and non-DNA evidence, revealing that police-induced false confessions are a leading cause of wrongful conviction of the innocent. In this article, empirical research on the causes and correlates of false confessions is reviewed. After a description of the three sequential processes that are responsible for the elicitation of false confessions--misclassification, coercion, and contamination--the three psychologically distinct types of false confession (voluntary, compliant, and persuaded) are discussed along with the consequences of introducing false-confession evidence in the criminal justice system. The article concludes with a brief discussion of the implications of empirical research for reducing the number of false confessions and improving the accuracy of confession evidence that is introduced against a defendant at trial. PMID:19767498

  5. Constructing rich false memories of committing crime.

    PubMed

    Shaw, Julia; Porter, Stephen

    2015-03-01

    Memory researchers long have speculated that certain tactics may lead people to recall crimes that never occurred, and thus could potentially lead to false confessions. This is the first study to provide evidence suggesting that full episodic false memories of committing crime can be generated in a controlled experimental setting. With suggestive memory-retrieval techniques, participants were induced to generate criminal and noncriminal emotional false memories, and we compared these false memories with true memories of emotional events. After three interviews, 70% of participants were classified as having false memories of committing a crime (theft, assault, or assault with a weapon) that led to police contact in early adolescence and volunteered a detailed false account. These reported false memories of crime were similar to false memories of noncriminal events and to true memory accounts, having the same kinds of complex descriptive and multisensory components. It appears that in the context of a highly suggestive interview, people can quite readily generate rich false memories of committing crime. PMID:25589599

  6. Constructing rich false memories of committing crime.

    PubMed

    Shaw, Julia; Porter, Stephen

    2015-03-01

    Memory researchers long have speculated that certain tactics may lead people to recall crimes that never occurred, and thus could potentially lead to false confessions. This is the first study to provide evidence suggesting that full episodic false memories of committing crime can be generated in a controlled experimental setting. With suggestive memory-retrieval techniques, participants were induced to generate criminal and noncriminal emotional false memories, and we compared these false memories with true memories of emotional events. After three interviews, 70% of participants were classified as having false memories of committing a crime (theft, assault, or assault with a weapon) that led to police contact in early adolescence and volunteered a detailed false account. These reported false memories of crime were similar to false memories of noncriminal events and to true memory accounts, having the same kinds of complex descriptive and multisensory components. It appears that in the context of a highly suggestive interview, people can quite readily generate rich false memories of committing crime.

  7. 21 CFR 872.3590 - Preformed plastic denture tooth.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Preformed plastic denture tooth. 872.3590 Section 872.3590 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3590 Preformed plastic denture tooth....

  8. 21 CFR 872.3590 - Preformed plastic denture tooth.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Preformed plastic denture tooth. 872.3590 Section 872.3590 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3590 Preformed plastic denture tooth....

  9. 21 CFR 181.27 - Plasticizers.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Plasticizers. 181.27 Section 181.27 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) PRIOR-SANCTIONED FOOD INGREDIENTS Specific Prior-Sanctioned Food Ingredients §...

  10. 21 CFR 181.27 - Plasticizers.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Plasticizers. 181.27 Section 181.27 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) PRIOR-SANCTIONED FOOD INGREDIENTS Specific Prior-Sanctioned Food Ingredients §...

  11. 21 CFR 181.27 - Plasticizers.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Plasticizers. 181.27 Section 181.27 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) PRIOR-SANCTIONED FOOD INGREDIENTS Specific Prior-Sanctioned Food Ingredients §...

  12. How Does Distinctive Processing Reduce False Recall?

    ERIC Educational Resources Information Center

    Hunt, R. Reed; Smith, Rebekah E.; Dunlap, Kathryn R.

    2011-01-01

    False memories arising from associatively related lists are a robust phenomenon that resists many efforts to prevent it. However, a few variables have been shown to reduce this form of false memory. Explanations for how the reduction is accomplished have focused on either output monitoring processes or constraints on access, but neither idea alone…

  13. 49 CFR 234.107 - False activation.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ..., DEPARTMENT OF TRANSPORTATION GRADE CROSSING SAFETY, INCLUDING SIGNAL SYSTEMS, STATE ACTION PLANS, AND... Grade Crossings § 234.107 False activation. Upon receipt of a credible report of a false activation, a railroad having maintenance responsibility for the highway-rail grade crossing warning system...

  14. 49 CFR 234.107 - False activation.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ..., DEPARTMENT OF TRANSPORTATION GRADE CROSSING SAFETY, INCLUDING SIGNAL SYSTEMS, STATE ACTION PLANS, AND... Grade Crossings § 234.107 False activation. Upon receipt of a credible report of a false activation, a railroad having maintenance responsibility for the highway-rail grade crossing warning system...

  15. 49 CFR 234.107 - False activation.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ..., DEPARTMENT OF TRANSPORTATION GRADE CROSSING SAFETY, INCLUDING SIGNAL SYSTEMS, STATE ACTION PLANS, AND... Grade Crossings § 234.107 False activation. Upon receipt of a credible report of a false activation, a railroad having maintenance responsibility for the highway-rail grade crossing warning system...

  16. 30 CFR 281.5 - False statements.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 2 2011-07-01 2011-07-01 false False statements. 281.5 Section 281.5 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE LEASING OF MINERALS OTHER THAN OIL, GAS, AND SULPHUR IN THE OUTER CONTINENTAL SHELF General §...

  17. 15 CFR 80.6 - False statements.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 15 Commerce and Foreign Trade 1 2011-01-01 2011-01-01 false False statements. 80.6 Section 80.6 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade BUREAU OF THE CENSUS, DEPARTMENT OF COMMERCE FURNISHING PERSONAL CENSUS DATA FROM CENSUS OF POPULATION SCHEDULES § 80.6...

  18. 15 CFR 80.6 - False statements.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 15 Commerce and Foreign Trade 1 2013-01-01 2013-01-01 false False statements. 80.6 Section 80.6 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade BUREAU OF THE CENSUS, DEPARTMENT OF COMMERCE FURNISHING PERSONAL CENSUS DATA FROM CENSUS OF POPULATION SCHEDULES § 80.6...

  19. 15 CFR 80.6 - False statements.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 15 Commerce and Foreign Trade 1 2012-01-01 2012-01-01 false False statements. 80.6 Section 80.6 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade BUREAU OF THE CENSUS, DEPARTMENT OF COMMERCE FURNISHING PERSONAL CENSUS DATA FROM CENSUS OF POPULATION SCHEDULES § 80.6...

  20. 15 CFR 80.6 - False statements.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 15 Commerce and Foreign Trade 1 2014-01-01 2014-01-01 false False statements. 80.6 Section 80.6 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade BUREAU OF THE CENSUS, DEPARTMENT OF COMMERCE FURNISHING PERSONAL CENSUS DATA FROM CENSUS OF POPULATION SCHEDULES § 80.6...

  1. 15 CFR 80.6 - False statements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false False statements. 80.6 Section 80.6 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade BUREAU OF THE CENSUS, DEPARTMENT OF COMMERCE FURNISHING PERSONAL CENSUS DATA FROM CENSUS OF POPULATION SCHEDULES § 80.6...

  2. Can False Memories Prime Problem Solutions?

    ERIC Educational Resources Information Center

    Howe, Mark L.; Garner, Sarah R.; Dewhurst, Stephen A.; Ball, Linden J.

    2010-01-01

    Previous research has suggested that false memories can prime performance on related implicit and explicit memory tasks. The present research examined whether false memories can also be used to prime higher order cognitive processes, namely, insight-based problem solving. Participants were asked to solve a number of compound remote associate task…

  3. Explaining the Development of False Memories.

    ERIC Educational Resources Information Center

    Reyna, Valerie F.; Holliday, Robyn; Marche, Tammy

    2002-01-01

    Reviews explanatory dimensions of children's false memory relevant to forensic practice: measurement, development, social factors, individual differences, varieties of memories and memory judgments, and varieties of procedures inducing false memories. Asserts that recent studies fail to use techniques that separate acquiescence from memory…

  4. 20 CFR 356.3 - False claims.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 20 Employees' Benefits 1 2014-04-01 2012-04-01 true False claims. 356.3 Section 356.3 Employees' Benefits RAILROAD RETIREMENT BOARD ADMINISTRATIVE REMEDIES FOR FRAUDULENT CLAIMS OR STATEMENTS CIVIL MONETARY PENALTY INFLATION ADJUSTMENT § 356.3 False claims. In the case of penalties assessed under 31...

  5. 20 CFR 356.3 - False claims.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 20 Employees' Benefits 1 2013-04-01 2012-04-01 true False claims. 356.3 Section 356.3 Employees' Benefits RAILROAD RETIREMENT BOARD ADMINISTRATIVE REMEDIES FOR FRAUDULENT CLAIMS OR STATEMENTS CIVIL MONETARY PENALTY INFLATION ADJUSTMENT § 356.3 False claims. In the case of penalties assessed under 31...

  6. Waste plastics liquefaction technology

    SciTech Connect

    Machidori, Hideki; Ikawa, Hironori

    1996-12-31

    Plastics are now indispensable not only in industries but for daily life because of their excellent convenience. Only in Japan, about 12.25 million tons of plastics were produced in 1993. On the other hand, the production of waste plastics in the form of industrial and municipal wastes reached 7.56 million tons in the same year. A greater part of the produced waste plastics are now disposed of by incineration and landfill. The incineration would however generate detrimental substances from burned-up plastics and emit them into the exhaust gas, while the landfill would reduce rapidly the residual capacity of the final repositories. Under the circumstances, the Law for the Promotion of Sorted Collection and Recommercialization of Plastics Containers and Packages is to be enforced in 2000 in Japan. Waste plastics liquefaction technology has become high-lighted and is presupposed to employ for the treatment of waste plastics other than PET bottles in the law for the reason that relatively wide variety of waste plastics can be processed in quantity by this technology. The Kubota Corporation has made R and D efforts relating to the plastics liquefaction technology for more than 4 years, and it is now entering the stage of its commercialization.

  7. How Plastics Work

    NASA Astrophysics Data System (ADS)

    Bloomfield, Louis

    2013-03-01

    We encounter plastics every day, but despite their widespread use, amazing range of properties, and basic scientific underpinnings, most physicists--like most people--know relatively little about plastics. In contrast to hard crystalline and amorphous solids (e.g., metals, salts, ceramics, and glasses), we take plastics for granted, select them carelessly, and examine them more closely only on a need-to-know basis. By ignoring plastics until we need them, however, we risk not knowing what we don't know and using the wrong ones. To repurpose a familiar advertisement, ``there's a plastic for that.'' This talk will review some of the basic physics and science of plastics. It will examine the roles of temperature, order, intermolecular forces, entanglements, and linkages in plastics, and how those issues affect the properties of a given plastic. We'll stop along the way to recognize a few of the more familiar plastics, natural and synthetic, and explain some of their mechanical, chemical, and optical properties. The talk will conclude by explaining the remarkable properties of a plastic that has been largely misunderstood since its discovery 70 years ago: Silly Putty.

  8. Our plastic age.

    PubMed

    Thompson, Richard C; Swan, Shanna H; Moore, Charles J; vom Saal, Frederick S

    2009-07-27

    Within the last few decades, plastics have revolutionized our daily lives. Globally we use in excess of 260 million tonnes of plastic per annum, accounting for approximately 8 per cent of world oil production. In this Theme Issue of Philosophical Transactions of the Royal Society, we describe current and future trends in usage, together with the many benefits that plastics bring to society. At the same time, we examine the environmental consequences resulting from the accumulation of waste plastic, the effects of plastic debris on wildlife and concerns for human health that arise from the production, usage and disposal of plastics. Finally, we consider some possible solutions to these problems together with the research and policy priorities necessary for their implementation.

  9. Our plastic age

    PubMed Central

    Thompson, Richard C.; Swan, Shanna H.; Moore, Charles J.; vom Saal, Frederick S.

    2009-01-01

    Within the last few decades, plastics have revolutionized our daily lives. Globally we use in excess of 260 million tonnes of plastic per annum, accounting for approximately 8 per cent of world oil production. In this Theme Issue of Philosophical Transactions of the Royal Society, we describe current and future trends in usage, together with the many benefits that plastics bring to society. At the same time, we examine the environmental consequences resulting from the accumulation of waste plastic, the effects of plastic debris on wildlife and concerns for human health that arise from the production, usage and disposal of plastics. Finally, we consider some possible solutions to these problems together with the research and policy priorities necessary for their implementation. PMID:19528049

  10. Our plastic age.

    PubMed

    Thompson, Richard C; Swan, Shanna H; Moore, Charles J; vom Saal, Frederick S

    2009-07-27

    Within the last few decades, plastics have revolutionized our daily lives. Globally we use in excess of 260 million tonnes of plastic per annum, accounting for approximately 8 per cent of world oil production. In this Theme Issue of Philosophical Transactions of the Royal Society, we describe current and future trends in usage, together with the many benefits that plastics bring to society. At the same time, we examine the environmental consequences resulting from the accumulation of waste plastic, the effects of plastic debris on wildlife and concerns for human health that arise from the production, usage and disposal of plastics. Finally, we consider some possible solutions to these problems together with the research and policy priorities necessary for their implementation. PMID:19528049

  11. Controlling false discoveries in genetic studies.

    PubMed

    van den Oord, Edwin J C G

    2008-07-01

    A false discovery occurs when a researcher concludes that a marker is involved in the etiology of the disease whereas in reality it is not. In genetic studies the risk of false discoveries is very high because only few among the many markers that can be tested will have an effect on the disease. In this article, we argue that it may be best to use methods for controlling false discoveries that would introduce the same ratio of false discoveries divided by all rejected tests into the literature regardless of systematic differences between studies. After a brief discussion of traditional "multiple testing" methods, we show that methods that control the false discovery rate (FDR) may be more suitable to achieve this goal. These FDR methods are therefore discussed in more detail. Instead of merely testing for main effects, it may be important to search for gene-environment/covariate interactions, gene-gene interactions or genetic variants affecting disease subtypes. In the second section, we point out the challenges involved in controlling false discoveries in such searches. The final section discusses the role of replication studies for eliminating false discoveries and the complexities associated with the definition of what constitutes a replication and the design of these studies.

  12. A Closer Look at Self-Reported Suicide Attempts: False Positives and False Negatives

    ERIC Educational Resources Information Center

    Ploderl, Martin; Kralovec, Karl; Yazdi, Kurosch; Fartacek, Reinhold

    2011-01-01

    The validity of self-reported suicide attempt information is undermined by false positives (e.g., incidences without intent to die), or by unreported suicide attempts, referred to as false negatives. In a sample of 1,385 Austrian adults, we explored the occurrence of false positives and false negatives with detailed, probing questions. Removing…

  13. Plasticized phenolphthalein polycarbonate

    NASA Technical Reports Server (NTRS)

    Harrison, E. S.

    1976-01-01

    Phenolphthalein polycarbonate was successfully plasticized with polychlorinated biphenyls (e.g., Aroclor 1231) or tricresyl phosphate and cast from tetrahydrofuran to give clear films without loss of fire resistance. At loadings of 20 to 30 percent plasticizer the Tg was lowered to approximately 100 C which would render phenolphthalein polycarbonate easily moldable. Although these materials had some mechanical integrity as shown by their film forming ability, the room temperature toughness of the plasticized polymer was not significantly improved over unmodified polymer.

  14. Plasticity and Geomechanics

    NASA Astrophysics Data System (ADS)

    Davis, R. O.; Selvadurai, A. P. S.

    2002-11-01

    Plasticity and Geomechanics is a concise introduction to the general subject of plasticity with a particular emphasis on applications in geomechanics. Derived from the authors' lecture notes, this book is written with students firmly in mind. Excessive use of mathematical methods is avoided and, where possible, physical interpretations are given for important concepts. The authors present a clear introduction to the complex ideas and concepts of plasticity and demonstrate how this developing subject is of critical importance to geomechanics and geotechnical engineering.

  15. Plasticity and Geomechanics

    NASA Astrophysics Data System (ADS)

    Davis, R. O.; Selvadurai, A. P. S.

    2005-08-01

    Plasticity and Geomechanics is a concise introduction to the general subject of plasticity with a particular emphasis on applications in geomechanics. Derived from the authors' lecture notes, this book is written with students firmly in mind. Excessive use of mathematical methods is avoided and, where possible, physical interpretations are given for important concepts. The authors present a clear introduction to the complex ideas and concepts of plasticity and demonstrate how this developing subject is of critical importance to geomechanics and geotechnical engineering.

  16. The false-negative Meckel's scan

    SciTech Connect

    Wilton, G.; Froelich, J.W.

    1982-10-01

    A case is presented of a 17-month-old girl who underwent two Meckel's scans with /sup 99m/Tc pertechnetate. The initial study was interpreted as normal while a subsequent study five days later was definitely positive. Surgery immediately following the positive Meckel's scan demonstrated a Meckel's diverticulum containing gastric mucosa without evidence of active hemorrhage. This prompted a review of the literature in reference to false-negative Meckel's scans which revealed a wide variance in the reported incidence of false-negative examinations. Repeat scintigraphy in the face of a strong clinical suspicion after an initial normal study may decrease the indicence of false-negative imaging series.

  17. Plastics and health risks.

    PubMed

    Halden, Rolf U

    2010-01-01

    By 2010, the worldwide annual production of plastics will surpass 300 million tons. Plastics are indispensable materials in modern society, and many products manufactured from plastics are a boon to public health (e.g., disposable syringes, intravenous bags). However, plastics also pose health risks. Of principal concern are endocrine-disrupting properties, as triggered for example by bisphenol A and di-(2-ethylhexyl) phthalate (DEHP). Opinions on the safety of plastics vary widely, and despite more than five decades of research, scientific consensus on product safety is still elusive. This literature review summarizes information from more than 120 peer-reviewed publications on health effects of plastics and plasticizers in lab animals and humans. It examines problematic exposures of susceptible populations and also briefly summarizes adverse environmental impacts from plastic pollution. Ongoing efforts to steer human society toward resource conservation and sustainable consumption are discussed, including the concept of the 5 Rs--i.e., reduce, reuse, recycle, rethink, restrain--for minimizing pre- and postnatal exposures to potentially harmful components of plastics.

  18. The plastics waste problem

    SciTech Connect

    Rowatt, R.J.

    1993-01-01

    Post-consumer plastic is a symptom of the municipal solid waste (MSW) problem, not the cause. Yet the U.S. public sees plastic as a major contributor to the waste stream. Two-thirds say the environmental risks of using plastics outweigh the benefits and that they favor mandatory recycling programs in their community; more than four-fifths think recycling can substantially reduce the amount of solid waste and decry the presence of nonbiodegradable plastics in landfills. Given this perception, the author reviews solid waste management issues and examines the contributions that resin producers can make.

  19. Coatings For Plastic Optics

    NASA Astrophysics Data System (ADS)

    Schaffer, Robert W.

    1983-11-01

    Over the past decade there has been a tremendous surge of interest in the use of plastic optical elements to supplement or replace glass optics. While the technology of molding and polishing plastic optics has been the chief interest, there has been increasing need for precision coatings for these elements. In some instances these coatings are as critical as the elements themselves. In this paper we will describe the difficulties incurred in coating plastic and some of the many coatings presently available today despite the difficulties encountered. We will then cover the durability aspects of these coatings and lastly, point out some areas to consider when evaluating using plastic instead of glass.

  20. The False Claims Act and clinical laboratories.

    PubMed

    Vogel, R L

    1993-01-01

    In its efforts to fight fraud, the government has turned increasingly to the civil False Claims Act. The Act imposes triple damages plus monetary penalties against those who defraud the federal government. The Act also encourages whistleblowers to report fraud by offering the prospect of large bounties. This article describes the False Claims Act, its qui tam provision dealing with whistleblowers, and the application of the Act to clinical laboratories.

  1. Review article: the false-bottom ice

    NASA Astrophysics Data System (ADS)

    Alexandrov, D. V.; Jouzel, J.; Nizovtseva, I.; Ryashko, L. B.

    2013-11-01

    Nansen from his observations in the Beaufort Sea published in 1897 noted that heat transfer from the fresh water (with a~temperature of 0 °C) to the arctic salt water (with a temperature of -1.6 °C) is the only source of ice accretion during the polar summer. This transfer mechanism, unusual at first sight, is responsible for the initiation and evolution of a false bottom ice, changing ice properties to a great extent and affecting various processes while interacting with the ocean and the atmosphere. The processes of false bottom ice growth from below (i.e. from the ocean to the atmosphere) become of prime importance in the era of global warming and climate change. In this review, we summarize the theoretical approaches, field and laboratory observations, conducted during more than 100 yr, in order to address the problem of false bottoms to a broad community of readers. We also discuss the recent modeling advances to which we have contributed. A "false bottom" is a thin layer of ice which forms in summer underneath the floe, where fresh water lies between the salt water and the ice. Such false bottoms represent the only significant source of ice growth in the Arctic during the spring-summer period. Their evolution influences the mass balance of the Arctic sea-ice cover, which is recognized as an indicator of climate change. However, the quantity, aerial extent and other properties of false bottoms are difficult to measure because coring under the surface melt ponds leads to direct mixing of surface and under-ice water. This explains why their aerial extent and overall volume is still not known despite the fact that the upper limit of the present-day estimate of the false bottom ice coverage is approximately half of the sea ice surface. The growth of false bottoms also leads to other important consequences for various physical, chemical and biological processes associated with their dynamics.

  2. False Discovery Rate Estimation in Proteomics.

    PubMed

    Aggarwal, Suruchi; Yadav, Amit Kumar

    2016-01-01

    With the advancement in proteomics separation techniques and improvements in mass analyzers, the data generated in a mass-spectrometry based proteomics experiment is rising exponentially. Such voluminous datasets necessitate automated computational tools for high-throughput data analysis and appropriate statistical control. The data is searched using one or more of the several popular database search algorithms. The matches assigned by these tools can have false positives and statistical validation of these false matches is necessary before making any biological interpretations. Without such procedures, the biological inferences do not hold true and may be outright misleading. There is a considerable overlap between true and false positives. To control the false positives amongst a set of accepted matches, there is a need for some statistical estimate that can reflect the amount of false positives present in the data processed. False discovery rate (FDR) is the metric for global confidence assessment of a large-scale proteomics dataset. This chapter covers the basics of FDR, its application in proteomics, and methods to estimate FDR.

  3. 7 CFR 58.318 - Butter, frozen or plastic cream melting machines.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Butter, frozen or plastic cream melting machines. 58... Service 1 Equipment and Utensils § 58.318 Butter, frozen or plastic cream melting machines. Shavers, shredders or melting machines used for rapid melting of butter, frozen or plastic cream shall be...

  4. 7 CFR 58.318 - Butter, frozen or plastic cream melting machines.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Butter, frozen or plastic cream melting machines. 58... Service 1 Equipment and Utensils § 58.318 Butter, frozen or plastic cream melting machines. Shavers, shredders or melting machines used for rapid melting of butter, frozen or plastic cream shall be...

  5. 7 CFR 58.318 - Butter, frozen or plastic cream melting machines.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Butter, frozen or plastic cream melting machines. 58... Service 1 Equipment and Utensils § 58.318 Butter, frozen or plastic cream melting machines. Shavers, shredders or melting machines used for rapid melting of butter, frozen or plastic cream shall be...

  6. 7 CFR 58.318 - Butter, frozen or plastic cream melting machines.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Butter, frozen or plastic cream melting machines. 58... Service 1 Equipment and Utensils § 58.318 Butter, frozen or plastic cream melting machines. Shavers, shredders or melting machines used for rapid melting of butter, frozen or plastic cream shall be...

  7. 7 CFR 58.318 - Butter, frozen or plastic cream melting machines.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Butter, frozen or plastic cream melting machines. 58... Service 1 Equipment and Utensils § 58.318 Butter, frozen or plastic cream melting machines. Shavers, shredders or melting machines used for rapid melting of butter, frozen or plastic cream shall be...

  8. 49 CFR 178.925 - Standards for rigid plastic Large Packagings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Standards for rigid plastic Large Packagings. 178... FOR PACKAGINGS Large Packagings Standards § 178.925 Standards for rigid plastic Large Packagings. (a) The provisions in this section apply to rigid plastic Large Packagings intended to contain liquids...

  9. 49 CFR 178.925 - Standards for rigid plastic Large Packagings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Standards for rigid plastic Large Packagings. 178... FOR PACKAGINGS Large Packagings Standards § 178.925 Standards for rigid plastic Large Packagings. (a) The provisions in this section apply to rigid plastic Large Packagings intended to contain liquids...

  10. 49 CFR 192.285 - Plastic pipe: Qualifying persons to make joints.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Plastic pipe: Qualifying persons to make joints... Materials Other Than by Welding § 192.285 Plastic pipe: Qualifying persons to make joints. (a) No person may make a plastic pipe joint unless that person has been qualified under the applicable joining...

  11. 24 CFR 3280.207 - Requirements for foam plastic thermal insulating materials.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 5 2013-04-01 2013-04-01 false Requirements for foam plastic... SAFETY STANDARDS Fire Safety § 3280.207 Requirements for foam plastic thermal insulating materials. (a) General. Foam plastic thermal insulating materials shall not be used within the cavity of walls...

  12. 24 CFR 3280.207 - Requirements for foam plastic thermal insulating materials.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 5 2012-04-01 2012-04-01 false Requirements for foam plastic... SAFETY STANDARDS Fire Safety § 3280.207 Requirements for foam plastic thermal insulating materials. (a) General. Foam plastic thermal insulating materials shall not be used within the cavity of walls...

  13. 49 CFR 192.285 - Plastic pipe: Qualifying persons to make joints.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Plastic pipe: Qualifying persons to make joints... Materials Other Than by Welding § 192.285 Plastic pipe: Qualifying persons to make joints. (a) No person may make a plastic pipe joint unless that person has been qualified under the applicable joining...

  14. 49 CFR 192.285 - Plastic pipe: Qualifying persons to make joints.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Plastic pipe: Qualifying persons to make joints... Materials Other Than by Welding § 192.285 Plastic pipe: Qualifying persons to make joints. (a) No person may make a plastic pipe joint unless that person has been qualified under the applicable joining...

  15. 49 CFR 192.285 - Plastic pipe: Qualifying persons to make joints.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Plastic pipe: Qualifying persons to make joints... Materials Other Than by Welding § 192.285 Plastic pipe: Qualifying persons to make joints. (a) No person may make a plastic pipe joint unless that person has been qualified under the applicable joining...

  16. 24 CFR 3280.207 - Requirements for foam plastic thermal insulating materials.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 5 2011-04-01 2011-04-01 false Requirements for foam plastic... SAFETY STANDARDS Fire Safety § 3280.207 Requirements for foam plastic thermal insulating materials. (a) General. Foam plastic thermal insulating materials shall not be used within the cavity of walls...

  17. 21 CFR 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Acrylic and modified acrylic plastics, semirigid... Acrylic and modified acrylic plastics, semirigid and rigid. Semirigid and rigid acrylic and modified acrylic plastics may be safely used as articles intended for use in contact with food, in accordance...

  18. 21 CFR 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Acrylic and modified acrylic plastics, semirigid... Acrylic and modified acrylic plastics, semirigid and rigid. Semirigid and rigid acrylic and modified acrylic plastics may be safely used as articles intended for use in contact with food, in accordance...

  19. 21 CFR 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Acrylic and modified acrylic plastics, semirigid... Acrylic and modified acrylic plastics, semirigid and rigid. Semirigid and rigid acrylic and modified acrylic plastics may be safely used as articles intended for use in contact with food, in accordance...

  20. Reinforced plastics durability

    SciTech Connect

    Pritchard, G.

    1999-01-01

    Written especially for first-time users of reinforced plastics. The book offers substantial introductory information with key concepts. Chapters examine the long-term threats to the integrity of reinforced plastics: outdoor weathering, solvent/water attack, high temperatures, and repetitive stress.

  1. Coatings for plastic glazing

    SciTech Connect

    Not Available

    1993-05-01

    This article describes how, as a replacement for glass, coated thermoplastic polymers can reduce cost and weight and increase occupant retention and design flexibility. Advances in transparent protective coatings have increased the potential for successful use of plastics in automotive applications. Originally, plastic materials were considered replacements for metals but, with proven performance, the utility of plastics is expanding beyond metal displacement. Now, transparent plastics are being considered as a potential replacement for glass. Driving this approach are many of the same reasons that plastics were first considered as alternatives to metals--cost, weight, design flexibility, and CAFE requirements. Glass has good optical properties, abrasion and chemical resistance, and outdoor durability, but it is also heavy, breakable, and expensive to form into intricate shapes. Although most clear plastics offer good optical properties, moldability, toughness, and cost benefits, their primary limitation is poor surface resistance to abrasion, scratching, chemicals, and the outdoor environment. In many cases, clear protective coatings can minimize these limitations. The potential advantages and disadvantages of plastic vs glass in automotive applications are given. Transparent plastic materials available for consideration as replacements for automotive glazing are listed.

  2. Detecting plastics in seedcotton

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The US cotton industry wants to increase market share and value by supplying pure cotton. Removing contamination requires developing a means to detect plastics in seedcotton. This study was conducted to determine if Ion Mobility Spectrometry (IMS) could be used to find small amounts of plastic in ...

  3. Remedies by competitors for false advertising.

    PubMed

    Hirsch, B D; Wilcox, D P

    1990-05-01

    Patients who are victimized as a consequence of false medical advertising are not the only ones who can sue for damages. Under section 43(a) of the Lanham Act, effective November 17, 1989, anyone "who believes that he or she is or is likely to be damaged" by deceptive advertising may bring a civil action for damages (1). Competing physicians may sue other physicians who falsely advertise that they possess unique skills and achieve better results than other physicians because they employ exclusive methods of treatment or claim that certain surgical procedures they perform in the office are absolutely safe and without risk or who advertise false professional credentials to lure patients. Voluntary informed consent excludes the use of deceit. Misrepresentation through advertising deprives a patient of the right to exercise an informed consent (2). A patient who relies on a doctor's false advertising in agreeing to a procedure that causes the patient injury may sue for malpractice even if the procedure was performed without negligence. False medical advertising also exposes the advertiser to litigation by competitors for unfair competition. This article is concerned with the remedy that may be available for instituting private litigation against physicians and other health care providers who engage in untruthful advertising. PMID:2343426

  4. Track recording plastic compositions

    NASA Technical Reports Server (NTRS)

    Tarle, Gregory (Inventor)

    1983-01-01

    Improved nuclear track recording plastic compositions are provided which exhibit greatly decreased surface roughness when etched to produce visible tracks of energetic nuclear particles which have passed into and/or through said plastic. The improved compositions incorporate a small quantity of a phthalic acid ester into the major plastic component which is derived from the polymerization of monomeric di-ethylene glycol bis allyl carbonate. Di-substituted phthalic acid esters are preferred as the added component, with the further perference that the ester substituent has a chain length of 2 or more carbon atoms. The inclusion of the phthalic acid ester to an extent of from about 1-2% by weight of the plastic compositions is sufficient to drastically reduce the surface roughness ordinarily produced when the track recording plastic is contacted by etchants.

  5. 77 FR 54930 - Carlyle Plastics and Resins, Formerly Known as Fortis Plastics, A Subsidiary of Plastics...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-06

    ... Employment and Training Administration Carlyle Plastics and Resins, Formerly Known as Fortis Plastics, A... determination was published in the Federal Register on Monday, July 23, 2012 (77 FR 43123). ] At the request of... plastic parts. New information shows that Fortis Plastics is now called Carlyle Plastics and Resins....

  6. False lock performance of quadriphase receivers

    NASA Technical Reports Server (NTRS)

    Simon, M. K.

    1979-01-01

    Quadriphase receivers, like biphase receivers, have the ability to false lock on a sideband on the data modulation. The theory associated with this phenomenon for receivers of binary phase-shift-keying (BPSK), using Costas loop demodulation, has recently been documented in the literature. This paper considers the corresponding theory for receivers of balanced quadriphase-shift-keying (QPSK) employing a quadriphase Costas loop (or equivalent fourth-power loop) for demodulation. Specific closed form expressions for false lock performance are developed and numerically evaluated for the particular case of single pole arm filters and an NRZ data format for each of the two statistically independent quadrature modulations.

  7. Plastic Surgery for Ethnic Patients

    MedlinePlus

    ... Briefing Papers > Plastic Surgery for Ethnic Patients Briefing Paper: Plastic Surgery for Ethnic Patients More than 3. ... 2067-2071. Share Related Links Plastic Surgery Briefing Papers Menu Cosmetic Reconstructive Patient Safety Before & After Find ...

  8. Interrogation and false confessions: vulnerability factors.

    PubMed

    Gudjonsson, G H

    This paper reviews the psychological factors that make some individuals susceptible to making a false confession of having committed a criminal offence. A number of 'vulnerability factors' are highlighted and it is emphasized that these need to be interpreted within the context of all circumstances surrounding the case. PMID:1591561

  9. A Synchronization Account of False Recognition

    ERIC Educational Resources Information Center

    Johns, Brendan T.; Jones, Michael N.; Mewhort, Douglas J. K.

    2012-01-01

    We describe a computational model to explain a variety of results in both standard and false recognition. A key attribute of the model is that it uses plausible semantic representations for words, built through exposure to a linguistic corpus. A study list is encoded in the model as a gist trace, similar to the proposal of fuzzy trace theory…

  10. 49 CFR 234.107 - False activation.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ..., DEPARTMENT OF TRANSPORTATION GRADE CROSSING SIGNAL SYSTEM SAFETY AND STATE ACTION PLANS Response to Reports... false activation, a railroad having maintenance responsibility for the highway-rail grade crossing... crossing by taking the following actions: (a) Prior to a train's arrival at the crossing, notify the...

  11. 49 CFR 234.107 - False activation.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ..., DEPARTMENT OF TRANSPORTATION GRADE CROSSING SIGNAL SYSTEM SAFETY AND STATE ACTION PLANS Response to Reports... false activation, a railroad having maintenance responsibility for the highway-rail grade crossing... crossing by taking the following actions: (a) Prior to a train's arrival at the crossing, notify the...

  12. 30 CFR 581.5 - False statements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE LEASING OF MINERALS OTHER... provisions of 18 U.S.C. 1001, it is a crime punishable by up to 5 years imprisonment or a fine of $10,000, or... States any false or fraudulent statement(s) to any matters within the Agency's jurisdiction....

  13. What Makes Language Learners False Beginners?

    ERIC Educational Resources Information Center

    Nakamura, Tomoko

    A study in Japan investigated second language skill loss and maintenance in three groups of English-as-a-Second-Language learners: (1) ninth graders studying basic vocabulary and sentence structures (true beginners); (2) students in the lowest level English class at a technical college, but with some English language skills (false beginners); and…

  14. Development of the False-Memory Illusion

    ERIC Educational Resources Information Center

    Brainerd, C. J.; Forrest, T. J.; Karibian, D.; Reyna, V. F.

    2006-01-01

    The counterintuitive developmental trend in the Deese-Roediger-McDermott (DRM) illusion (that false-memory responses increase with age) was investigated in learning-disabled and nondisabled children from the 6- to 14-year-old age range. Fuzzy-trace theory predicts that because there are qualitative differences in how younger versus older children…

  15. How to Justify Teaching False Science

    ERIC Educational Resources Information Center

    Slater, Matthew H.

    2008-01-01

    We often knowingly teach false science. Such a practice conflicts with a prima facie pedagogical value placed on teaching only what is true. I argue that only a partial dissolution of the conflict is possible: the proper aim of instruction in science is not to provide an armory of facts about what things the world contains, how they interact, and…

  16. Infants' Reasoning about Others' False Perceptions

    ERIC Educational Resources Information Center

    Song, Hyun-joo; Baillargeon, Renee

    2008-01-01

    Prior research suggests that children younger than age 3 or 4 do not understand that an agent may be deceived by an object's misleading appearance. The authors asked whether 14.5-month-olds would give evidence in a violation-of-expectation task that they understand that agents may form false perceptions. Infants first watched events in which an…

  17. False positive reduction for lung nodule CAD

    NASA Astrophysics Data System (ADS)

    Zhao, Luyin; Boroczky, Lilla; Drysdale, Jeremy; Agnihotri, Lalitha; Lee, Michael C.

    2007-03-01

    Computer-aided detection (CAD) algorithms 'automatically' identify lung nodules on thoracic multi-slice CT scans (MSCT) thereby providing physicians with a computer-generated 'second opinion'. While CAD systems can achieve high sensitivity, their limited specificity has hindered clinical acceptance. To overcome this problem, we propose a false positive reduction (FPR) system based on image processing and machine learning to reduce the number of false positive lung nodules identified by CAD algorithms and thereby improve system specificity. To discriminate between true and false nodules, twenty-three 3D features were calculated from each candidate nodule's volume of interest (VOI). A genetic algorithm (GA) and support vector machine (SVM) were then used to select an optimal subset of features from this pool of candidate features. Using this feature subset, we trained an SVM classifier to eliminate as many false positives as possible while retaining all the true nodules. To overcome the imbalanced nature of typical datasets (significantly more false positives than true positives), an intelligent data selection algorithm was designed and integrated into the machine learning framework, thus further improving the FPR rate. Three independent datasets were used to train and validate the system. Using two datasets for training and the third for validation, we achieved a 59.4% FPR rate while removing one true nodule on the validation datasets. In a second experiment, 75% of the cases were randomly selected from each of the three datasets and the remaining cases were used for validation. A similar FPR rate and true positive retention rate was achieved. Additional experiments showed that the GA feature selection process integrated with the proposed data selection algorithm outperforms the one without it by 5%-10% FPR rate. The methods proposed can be also applied to other application areas, such as computer-aided diagnosis of lung nodules.

  18. False alarm reduction in critical care.

    PubMed

    Clifford, Gari D; Silva, Ikaro; Moody, Benjamin; Li, Qiao; Kella, Danesh; Chahin, Abdullah; Kooistra, Tristan; Perry, Diane; Mark, Roger G

    2016-08-01

    High false alarm rates in the ICU decrease quality of care by slowing staff response times while increasing patient delirium through noise pollution. The 2015 PhysioNet/Computing in Cardiology Challenge provides a set of 1250 multi-parameter ICU data segments associated with critical arrhythmia alarms, and challenges the general research community to address the issue of false alarm suppression using all available signals. Each data segment was 5 minutes long (for real time analysis), ending at the time of the alarm. For retrospective analysis, we provided a further 30 seconds of data after the alarm was triggered. A total of 750 data segments were made available for training and 500 were held back for testing. Each alarm was reviewed by expert annotators, at least two of whom agreed that the alarm was either true or false. Challenge participants were invited to submit a complete, working algorithm to distinguish true from false alarms, and received a score based on their program's performance on the hidden test set. This score was based on the percentage of alarms correct, but with a penalty that weights the suppression of true alarms five times more heavily than acceptance of false alarms. We provided three example entries based on well-known, open source signal processing algorithms, to serve as a basis for comparison and as a starting point for participants to develop their own code. A total of 38 teams submitted a total of 215 entries in this year's Challenge. This editorial reviews the background issues for this challenge, the design of the challenge itself, the key achievements, and the follow-up research generated as a result of the Challenge, published in the concurrent special issue of Physiological Measurement. Additionally we make some recommendations for future changes in the field of patient monitoring as a result of the Challenge. PMID:27454172

  19. False Belief vs. False Photographs: A Test of Theory of Mind or Working Memory?

    PubMed

    Callejas, Alicia; Shulman, Gordon L; Corbetta, Maurizio

    2011-01-01

    Theory of mind (ToM), the ability to reason about other people's thoughts and beliefs, has been traditionally studied in behavioral and neuroimaging experiments by comparing performance in "false belief" and "false photograph" (control) stories. However, some evidence suggests that these stories are not matched in difficulty, complicating the interpretation of results. Here, we more fully evaluated the relative difficulty of comprehending these stories and drawing inferences from them. Subjects read false belief and false photograph stories followed by comprehension questions that probed true ("reality" questions) or false beliefs ("representation" questions) appropriate to the stories. Stories and comprehension questions were read and answered, respectively, more slowly in the false photograph than false belief conditions, indicating their greater difficulty. Interestingly, accuracy on representation questions for false photograph stories was significantly lower than for all other conditions and correlated positively with participants' working memory span scores. These results suggest that drawing representational inferences from false photo stories is particularly difficult and places heavy demands on working memory. Extensive naturalistic practice with ToM reasoning may enable a more flexible and efficient mental representation of false belief stories, resulting in lower memory load requirements. An important implication of these results is that the differential modulation of right temporal-parietal junction (RTPJ) during ToM and "false photo" control conditions may reflect the documented negative correlation of RTPJ activity with working memory load rather than a specialized involvement in ToM processes.

  20. The problem with false vacuum Higgs inflation

    SciTech Connect

    Fairbairn, Malcolm; Grothaus, Philipp; Hogan, Robert E-mail: philipp.grothaus@kcl.ac.uk

    2014-06-01

    We investigate the possibility of using the only known fundamental scalar, the Higgs, as an inflaton with minimal coupling to gravity. The peculiar appearance of a plateau or a false vacuum in the renormalised effective scalar potential suggests that the Higgs might drive inflation. For the case of a false vacuum we use an additional singlet scalar field, motivated by the strong CP problem, and its coupling to the Higgs to lift the barrier allowing for a graceful exit from inflation by mimicking hybrid inflation. We find that this scenario is incompatible with current measurements of the Higgs mass and the QCD coupling constant and conclude that the Higgs can only be the inflaton in more complicated scenarios.

  1. Spirit Beholds Bumpy Boulder (False Color)

    NASA Technical Reports Server (NTRS)

    2006-01-01

    As NASA's Mars Exploration Rover Spirit began collecting images for a 360-degree panorama of new terrain, the rover captured this view of a dark boulder with an interesting surface texture. The boulder sits about 40 centimeters (16 inches) tall on Martian sand about 5 meters (16 feet) away from Spirit. It is one of many dark, volcanic rock fragments -- many pocked with rounded holes called vesicles -- littering the slope of 'Low Ridge.' The rock surface facing the rover is similar in appearance to the surface texture on the outside of lava flows on Earth.

    Spirit took this false-color image with the panoramic camera on the rover's 810th sol, or Martian day, of exploring Mars (April 13, 2006). This image is a false-color rendering using camera's 753-nanometer, 535-nanometer, and 432-nanometer filters.

  2. False beats in coupled piano string unisons

    NASA Astrophysics Data System (ADS)

    Capleton, Brian

    2004-02-01

    The behavior of a unison pair of piano strings coupled by the soundboard bridge, when one string has localized anisotropy in the reactive part of the bridge admittance for a given partial frequency, can be investigated using a theoretical matrix description. The anisotropy can cause what in piano tuning terminology is referred to as ``false beating'' in a partial of the single string. A mathematical model can be used to illustrate how ``mistunings'' between the strings of the unison (measured when the strings are sounding in isolation from each other) may theoretically arise as a consequence of the normal practice in piano tuning, of eliminating or reducing audible beating in the unison when both strings are sounding. ``False beats'' in a single string partial can be ``inherited'' by a partial of the coupled unison's spectrum, and mistunings between the strings can eliminate or reduce the appearance of this inheritance.

  3. [False memory syndrome: state of the art].

    PubMed

    Nemets, Boris; Witztum, Eliezer; Kotler, Moshe

    2002-08-01

    The review describes the heated dispute on the present state of recovered traumatic memories. There are two main schools concerning the status of recovered memories of child abuse. One school believes in their authenticity unconditionally. Those who oppose the authenticity claim False Memory Syndrome's existence. They describe it as "a serious form of psychopathology characterized by strongly believed pseudomemories of childhood sexual abuse" and "condition in which a person's identity and interpersonal relationships are centered around a memory of traumatic experience which is objectively false but in which the person strongly believes". This review presents the allegations of both sides involved in the dispute, with updates of scientific and judicial references and relevant recommendations to care takers.

  4. False beats in coupled piano string unisons.

    PubMed

    Capleton, Brian

    2004-02-01

    The behavior of a unison pair of piano strings coupled by the soundboard bridge, when one string has localized anisotropy in the reactive part of the bridge admittance for a given partial frequency, can be investigated using a theoretical matrix description. The anisotropy can cause what in piano tuning terminology is referred to as "false beating" in a partial of the single string. A mathematical model can be used to illustrate how "mistunings" between the strings of the unison (measured when the strings are sounding in isolation from each other) may theoretically arise as a consequence of the normal practice in piano tuning, of eliminating or reducing audible beating in the unison when both strings are sounding. "False beats" in a single string partial can be "inherited" by a partial of the coupled unison's spectrum, and mistunings between the strings can eliminate or reduce the appearance of this inheritance. PMID:15000199

  5. Accounting for false negatives in hotspot detection

    SciTech Connect

    Sego, Landon H.; Wilson, John E.

    2007-08-28

    Hotspot sampling designs are used in environmental sampling to identify the location of one (or more) contiguous regions of elevated contamination. These regions are known as hotspots. The problem of how to calculate the probability of detecting an elliptical hotspot using a rectangular or triangular grid of sampling points was addressed by Singer and Wickman in 1969. This approach presumed that any sample which coincided with a hotspot would detect the hotspot without error. However, for many sampling methodologies, there is a chance that the hotspot will not be detected even though it has been sampled directly--a false negative. We present a mathematical solution and a numerical algorithm which account for false negatives when calculating the probability of detecting hotspots that are circular in shape.

  6. Detecting false intent using eye blink measures

    PubMed Central

    Marchak, Frank M.

    2013-01-01

    Eye blink measures have been shown to be diagnostic in detecting deception regarding past acts. Here we examined—across two experiments with increasing degrees of ecological validity—whether changes in eye blinking can be used to determine false intent regarding future actions. In both experiments, half of the participants engaged in a mock crime and then transported an explosive device with the intent of delivering it to a “contact” that would use it to cause a disturbance. Eye blinking was measured for all participants when presented with three types of questions: relevant to intent to transport an explosive device, relevant to intent to engage in an unrelated illegal act, and neutral questions. Experiment 1 involved standing participants watching a video interviewer with audio presented ambiently. Experiment 2 involved standing participants questioned by a live interviewer. Across both experiments, changes in blink count during and immediately following individual questions, total number of blinks, and maximum blink time length differentiated those with false intent from truthful intent participants. In response to questions relevant to intent to deliver an explosive device vs. questions relevant to intent to deliver illegal drugs, those with false intent showed a suppression of blinking during the questions when compared to the 10 s period after the end of the questions, a lower number of blinks, and shorter maximum blink duration. The results are discussed in relation to detecting deception about past activities as well as to the similarities and differences to detecting false intent as described by prospective memory and arousal. PMID:24130546

  7. False Context Fear Memory in Rats

    ERIC Educational Resources Information Center

    Bae, Sarah; Holmes, Nathan M.; Westbrook, R. Frederick

    2015-01-01

    Four experiments used rats to study false context fear memories. In Experiment 1, rats were pre-exposed to a distinctive chamber (context A) or to a control environment (context C), shocked after a delay in a second chamber (context B) and tested either in B or A. Rats pre-exposed to A froze just as much as control rats in B but more than control…

  8. False confessions, expert testimony, and admissibility.

    PubMed

    Watson, Clarence; Weiss, Kenneth J; Pouncey, Claire

    2010-01-01

    The confession of a criminal defendant serves as a prosecutor's most compelling piece of evidence during trial. Courts must preserve a defendant's constitutional right to a fair trial while upholding the judicial interests of presenting competent and reliable evidence to the jury. When a defendant seeks to challenge the validity of that confession through expert testimony, the prosecution often contests the admissibility of the expert's opinion. Depending on the content and methodology of the expert's opinion, testimony addressing the phenomenon of false confessions may or may not be admissible. This article outlines the scientific and epistemological bases of expert testimony on false confession, notes the obstacles facing its admissibility, and provides guidance to the expert in formulating opinions that will reach the judge or jury. We review the 2006 New Jersey Superior Court decision in State of New Jersey v. George King to illustrate what is involved in the admissibility of false-confession testimony and use the case as a starting point in developing a best-practice approach to working in this area. PMID:20542936

  9. False confessions, expert testimony, and admissibility.

    PubMed

    Watson, Clarence; Weiss, Kenneth J; Pouncey, Claire

    2010-01-01

    The confession of a criminal defendant serves as a prosecutor's most compelling piece of evidence during trial. Courts must preserve a defendant's constitutional right to a fair trial while upholding the judicial interests of presenting competent and reliable evidence to the jury. When a defendant seeks to challenge the validity of that confession through expert testimony, the prosecution often contests the admissibility of the expert's opinion. Depending on the content and methodology of the expert's opinion, testimony addressing the phenomenon of false confessions may or may not be admissible. This article outlines the scientific and epistemological bases of expert testimony on false confession, notes the obstacles facing its admissibility, and provides guidance to the expert in formulating opinions that will reach the judge or jury. We review the 2006 New Jersey Superior Court decision in State of New Jersey v. George King to illustrate what is involved in the admissibility of false-confession testimony and use the case as a starting point in developing a best-practice approach to working in this area.

  10. Evaluating promotional claims as false or misleading.

    PubMed

    Brushwood, David B; Knox, Caitlin A; Liu, Wei; Jenkins, Kevin A

    2013-11-01

    In light of the "false or misleading" standard resulting from the recent legal ruling, it can be concluded that a true claim is one that is both factually and analytically true. Factual truth could be based on the accuracy of the information and the sufficiency of the information. Analytical truth could be based on the scientific foundation for the claim and whether the information within the claim is presented in a balanced way. Regarding the assessment of whether a truthful claim is misleading, the evaluator could consider the relevance, consistency, and context of the information. Standards are important in medication use and medication regulation. Health care professionals who must decide whether a claim is truthful and not misleading will rely on guidance from FDA in determining how to evaluate promotional claims. As the court suggested in the case reviewed here, FDA could take the lead and provide guidance "in differentiating between misleading and false promotion, exaggerations and embellishments, and truthful or non-misleading information." Existing FDA regulations provide a foundation for such guidance. The next step for the agency would be to expand existing guidance to specifically describe how an off-label claim can be identified as either false or misleading. PMID:24128969

  11. Shape-Shifting Plastic

    SciTech Connect

    2015-05-20

    A new plastic developed by ORNL and Washington State University transforms from its original shape through a series of temporary shapes and returns to its initial form. The shape-shifting process is controlled through changes in temperature

  12. A Plastic Menagerie

    ERIC Educational Resources Information Center

    Hadley, Mary Jane

    2010-01-01

    Bobble heads had become quite popular, depicting all sorts of sports figures, animals, and even presidents. In this article, the author describes how her fourth graders made bobble head sculptures out of empty plastic drink bottles. (Contains 1 online resource.)

  13. Mechanical plasticity of cells

    NASA Astrophysics Data System (ADS)

    Bonakdar, Navid; Gerum, Richard; Kuhn, Michael; Spörrer, Marina; Lippert, Anna; Schneider, Werner; Aifantis, Katerina E.; Fabry, Ben

    2016-10-01

    Under mechanical loading, most living cells show a viscoelastic deformation that follows a power law in time. After removal of the mechanical load, the cell shape recovers only incompletely to its original undeformed configuration. Here, we show that incomplete shape recovery is due to an additive plastic deformation that displays the same power-law dynamics as the fully reversible viscoelastic deformation response. Moreover, the plastic deformation is a constant fraction of the total cell deformation and originates from bond ruptures within the cytoskeleton. A simple extension of the prevailing viscoelastic power-law response theory with a plastic element correctly predicts the cell behaviour under cyclic loading. Our findings show that plastic energy dissipation during cell deformation is tightly linked to elastic cytoskeletal stresses, which suggests the existence of an adaptive mechanism that protects the cell against mechanical damage.

  14. Recycle plastics into feedstocks

    SciTech Connect

    Kastner, H.; Kaminsky, W.

    1995-05-01

    Thermal cracking of mixed-plastics wastes with a fluidized-bed reactor can be a viable and cost-effective means to meet mandatory recycling laws. Strict worldwide environmental statutes require the hydrocarbon processing industry (HPI) to develop and implement product applications and technologies that reuse post-consumer mixed-plastics waste. Recycling or reuse of plastics waste has a broad definition. Recycling entails more than mechanical regranulation and remelting of polymers for film and molding applications. A European consortium of academia and refiners have investigated if it is possible and profitable to thermally crack plastics into feedstocks for refining and petrochemical applications. Development and demonstration of pyrolysis methods show promising possibilities of converting landfill garbage into valuable feedstocks such as ethylene, propylene, BTX, etc. Fluidized-bed reactor technologies offer HPI operators a possible avenue to meet recycling laws, conserve raw materials and yield a profit. The paper describes thermal cracking for feedstocks and pyrolysis of polyolefins.

  15. Dreaming in plastic

    NASA Astrophysics Data System (ADS)

    Korzhov, Marianna; Andelman, David; Shikler, Rafi

    2008-07-01

    Plastic is one of the most versatile materials available. It is cheap, flexible and easy to process, and as a result it is all around us - from our computer keyboards to the soles of our shoes. One of its most common applications is as an insulating coating for electric wires; indeed, plastic is well known for its insulating characteristics. It came as something of a surprise, therefore, when in the late 1970s a new generation of plastics was discovered that displayed exactly the opposite behaviour - the ability to conduct electricity. In fact, plastics can be made with a whole range of conductivities - there are polymer materials that behave like semiconductors and there are those that can conduct as well as metals. This discovery sparked a revolution in the electronics community, and three decades of research effort is now yielding a range of stunning new applications for this ubiquitous material.

  16. Cortical plasticity and rehabilitation.

    PubMed

    Moucha, Raluca; Kilgard, Michael P

    2006-01-01

    The brain is constantly adapting to environmental and endogenous changes (including injury) that occur at every stage of life. The mechanisms that regulate neural plasticity have been refined over millions of years. Motivation and sensory experience directly shape the rewiring that makes learning and neurological recovery possible. Guiding neural reorganization in a manner that facilitates recovery of function is a primary goal of neurological rehabilitation. As the rules that govern neural plasticity become better understood, it will be possible to manipulate the sensory and motor experience of patients to induce specific forms of plasticity. This review summarizes our current knowledge regarding factors that regulate cortical plasticity, illustrates specific forms of reorganization induced by control of each factor, and suggests how to exploit these factors for clinical benefit.

  17. Laser cutting plastic materials

    SciTech Connect

    Van Cleave, R.A.

    1980-08-01

    A 1000-watt CO/sub 2/ laser has been demonstrated as a reliable production machine tool for cutting of plastics, high strength reinforced composites, and other nonmetals. More than 40 different plastics have been laser cut, and the results are tabulated. Applications for laser cutting described include fiberglass-reinforced laminates, Kevlar/epoxy composites, fiberglass-reinforced phenolics, nylon/epoxy laminates, ceramics, and disposable tooling made from acrylic.

  18. The Need for Plastics Education.

    ERIC Educational Resources Information Center

    Society of Plastics Engineers, Inc., Stamford, CT.

    In view of a lack of trained personnel in the industry, the Plastics Education Foundation proposes that educators (1) add more plastics programs, (2) establish plastics engineering degrees at appropriate 4-year institutions, (3) add plastics processing technology to current engineering curricula, and (4) interest younger students in courses and/or…

  19. Uranus in True and False Color

    NASA Technical Reports Server (NTRS)

    1986-01-01

    These two pictures of Uranus -- one in true color (left) and the other in false color -- were compiled from images returned Jan. 17, 1986, by the narrow-angle camera of Voyager 2. The spacecraft was 9.1 million kilometers (5.7 million miles) from the planet, several days from closest approach. The picture at left has been processed to show Uranus as human eyes would see it from the vantage point of the spacecraft. The picture is a composite of images taken through blue, green and orange filters. The darker shadings at the upper right of the disk correspond to the day-night boundary on the planet. Beyond this boundary lies the hidden northern hemisphere of Uranus, which currently remains in total darkness as the planet rotates. The blue-green color results from the absorption of red light by methane gas in Uranus' deep, cold and remarkably clear atmosphere. The picture at right uses false color and extreme contrast enhancement to bring out subtle details in the polar region of Uranus. Images obtained through ultraviolet, violet and orange filters were respectively converted to the same blue, green and red colors used to produce the picture at left. The very slight contrasts visible in true color are greatly exaggerated here. In this false-color picture, Uranus reveals a dark polar hood surrounded by a series of progressively lighter concentric bands. One possible explanation is that a brownish haze or smog, concentrated over the pole, is arranged into bands by zonal motions of the upper atmosphere. The bright orange and yellow strip at the lower edge of the planet's limb is an artifact of the image enhancement. In fact, the limb is dark and uniform in color around the planet. The Voyager project is manages for NASA by the Jet Propulsion Laboratory.

  20. False belief in infancy: a fresh look.

    PubMed

    Heyes, Cecilia

    2014-09-01

    Can infants appreciate that others have false beliefs? Do they have a theory of mind? In this article I provide a detailed review of more than 20 experiments that have addressed these questions, and offered an affirmative answer, using nonverbal 'violation of expectation' and 'anticipatory looking' procedures. Although many of these experiments are both elegant and ingenious, I argue that their results can be explained by the operation of domain-general processes and in terms of 'low-level novelty'. This hypothesis suggests that the infants' looking behaviour is a function of the degree to which the observed (perceptual novelty) and remembered or expected (imaginal novelty) low-level properties of the test stimuli - their colours, shapes and movements - are novel with respect to events encoded by the infants earlier in the experiment. If the low-level novelty hypothesis is correct, research on false belief in infancy currently falls short of demonstrating that infants have even an implicit theory of mind. However, I suggest that the use of two experimental strategies - inanimate control procedures, and self-informed belief induction - could be used in combination with existing methods to bring us much closer to understanding the evolutionary and developmental origins of theory of mind. PMID:24666559

  1. False belief understanding in maltreated children.

    PubMed

    Cicchetti, Dante; Rogosch, Fred A; Maughan, Angeline; Toth, Sheree L; Bruce, Jacqueline

    2003-01-01

    False belief understanding was investigated in maltreated (N = 203), low socioeconomic status (SES) nonmaltreated (N = 143), and middle SES nonmaltreated (N = 172) 3- to 8-year-old children. Contrasts among the three groups provided an opportunity to examine the impact of family contextual influences on theory of mind development. Specifically, child maltreatment served as an "experiment of nature" in order to elucidate theory of mind abilities. Two false belief tasks and language assessments were administered. Among children with a verbal mental age of 49 months or greater, maltreatment was related to delays in the development of theory of mind, beyond the influence of chronological age and SES. The occurrence of maltreatment during the toddler period, onset during the toddler years, and physical abuse were features of maltreatment associated with delay in the development of theory of mind. Findings are discussed in terms of the influence of harsh caregiving on the development of theory of mind. Implications for the understanding of normal developmental processes are highlighted. PMID:14984138

  2. The plasticity of clays

    USGS Publications Warehouse

    Group, F.F.

    1905-01-01

    (1) Sand injures plasticity little at first because the grains are suspended in a plastic mass. It is only when grains are abundant enough to come in contact with their neighbors, that the effect becomes serious, and then both strength and amount of possible flow are injured. (2) Certain rare organic colloids increase the plasticity by rendering the water viscous. (3) Fineness also tends to increase plasticity. (4) Plane surfaces (plates) increase the amount of possible flow. They also give a chance for lubrication by thinner films, thus increasing the friction of film, and the strength of the whole mass. The action of plates is thus twofold ; but fineness may be carried to such an extent as to break up plate-like grains into angular fragments. The beneficial effects of plates are also decreased by the fact that each is so closely surrounded by others in the mass. (5) Molecular attraction is twofold in increasing plasticity. As the attraction increases, the coherence and strength of the mass increase, and the amount of possible deformation before crumbling also increases. Fineness increases this action by requiring more water. Colloids and crystalloids in solution may also increase the attraction. It is thus seen to be more active than any other single factor.

  3. [The false equivalent Galeazzi in children].

    PubMed

    Marzouki, A; Elibrahimi, A; Elmrini, A; Boutayeb, F

    2009-02-01

    We report the case of a false Galeazzi equivalent in children. This injury is characterised by an epiphyseal detachment of the distal extremity of the ulna rather than a distal radio-ulnar dislocation. A 16-year-old patient was injured in a fall from a bike. Radiographs showed a fracture of the radial shaft with anterior angulation, together with a type II Salter-Harris epiphyseal injury at the level of the distal ulna. We were unable to perform a closed reduction under general anesthesia due to interposition of periosteum at the fracture site. Thus surgical management was the only option, which consisted of removing the offending periosteum and performing osteosynthesis of the radial shaft fracture with a plate, and the epiphyseal detachment with pins. After 10 months, we noted no bone growth disturbance, or any reduced mobility of the wrist. We will continue the follow-up to monitor bone growth disturbance of the distal extremity of the ulna.

  4. Opportunity View of 'Gilbert' Layer (False Color)

    NASA Technical Reports Server (NTRS)

    2008-01-01

    This view from NASA's Mars Exploration Rover Opportunity shows bedock within a stratigraphic layer informally named 'Gilbert,' which is the rover's next target after completing an examination of three stratigtaphic layers forming a bright band around the inside of Victoria Crater. The rover will descend deeper into the crater to reach the Gilbert layer.

    Opportunity used its panoramic camera (Pancam) to capture this image with low-sun angle at a local solar time of 3:30 p.m. during the rover's 1,429th Martian day, of sol (Jan. 31, 2008).

    This view combines separate images taken through the Pancam filters centered on wavelengths of 753 nanometers, 535 nanometers and 432 nanometers. It is presented in a false-color stretch to bring out subtle color differences in the scene.

  5. Testing jumps via false discovery rate control.

    PubMed

    Yen, Yu-Min

    2013-01-01

    Many recently developed nonparametric jump tests can be viewed as multiple hypothesis testing problems. For such multiple hypothesis tests, it is well known that controlling type I error often makes a large proportion of erroneous rejections, and such situation becomes even worse when the jump occurrence is a rare event. To obtain more reliable results, we aim to control the false discovery rate (FDR), an efficient compound error measure for erroneous rejections in multiple testing problems. We perform the test via the Barndorff-Nielsen and Shephard (BNS) test statistic, and control the FDR with the Benjamini and Hochberg (BH) procedure. We provide asymptotic results for the FDR control. From simulations, we examine relevant theoretical results and demonstrate the advantages of controlling the FDR. The hybrid approach is then applied to empirical analysis on two benchmark stock indices with high frequency data.

  6. Layered Outcrops in Gusev Crater (False Color)

    NASA Technical Reports Server (NTRS)

    2004-01-01

    One of the ways scientists collect mineralogical data about rocks on Mars is to view them through filters that allow only specific wavelengths of light to pass through the lens of the panoramic camera. NASA's Mars Exploration Rover Spirit took this false-color image of the rock nicknamed 'Tetl' at 1:05 p.m. martian time on its 270th martian day, or sol (Oct. 5, 2004) using the panoramic camera's 750-, 530-, and 430-nanometer filters. Darker red hues in the image correspond to greater concentrations of oxidized soil and dust. Bluer hues correspond to portions of rock that are not as heavily coated with soils or are not as highly oxidized.

  7. Right ventricular false tendons, a cadaveric approach.

    PubMed

    Loukas, Marios; Wartmann, Christopher T; Tubbs, R Shane; Apaydin, Nihal; Louis, Robert G; Black, Brandie; Jordan, Robert

    2008-06-01

    Left ventricular false tendons (LFTs) have been extensively described and recognized by gross anatomic studies. However, there is very little information available regarding right ventricular false tendons (RFTs). The aim of our study, therefore, was to explore and delineate the morphology, topography and morphometry of the RFTs, and provide a comprehensive picture of their anatomy across a broad range of specimens. We identified 35/100 heart specimens containing right ventricular RFTs and classified them into five types. In Type I (21, 47.7%) the RFTs, was located between the ventricular septum and the anterior papillary muscle; in Type II (11, 22.9%) between ventricular septum and the posterior papillary muscle; in Type III (7, 14.5%) between the anterior leaflet of the tricuspid valve and the right ventricular free wall; in Type IV (5, 10.4%) between the posterior papillary muscle and the ventricular free wall; and lastly, in Type V (4, 8.3%) between the anterior papillary muscle and ventricular free wall. The mean length of the RFTs was 18 +/- 7 mm with a mean diameter of 1.4 +/- 05 mm. Histologic examination with Masson trichrome and PAS revealed that 20 (41.6%) of the 48 RFTs carried conduction tissue fibers. The presence of conduction tissue fibers within the RFTs was limited to Types I, III, and IV. In Types II and V the RFTs resembled fibrous structures in contrast with Type I, II and IV, which were composed more of muscular fibers, including conduction tissue fibers. RFTs containing conduction tissue fibers were identified, which may implicate them in the appearance of arrhythmias.

  8. Constraining Oxygen False Positives in Planetary Atmospheres

    NASA Astrophysics Data System (ADS)

    Harman, C. E.; Schottelkotte, J. C.; Kasting, J. F.

    2014-03-01

    Oxygen (O2) and ozone (O3) in the present Earth's atmosphere are byproducts of oxygenic photosynthesis coupled with organic carbon burial. On Earth, no known abiotic surface process would be able to generate such an atmosphere, and by extension, lifeless exoplanets are expected to be devoid of O2. As a result, molecular oxygen and ozone are often seen as convincing signposts for life. Recently, however, a number of authors have demonstrated the abiotic generation of molecular oxygen in a planetary atmosphere, either under oxidizing conditions (Hu et al., 2013) or around an M star (Tian et al., 2013). This èfalse positive', if verified, would remove oxygen and ozone from an already short list of easily detectable biosignatures. We explore oxygen false positives with our 1-D photochemical model, updated from Segura et al. (2007). Preliminary results show that if water vapor photolysis longward of ~200 nm is neglected, substantial amounts of CO and O2 can build up in the lower part of the atmosphere. Additionally, the ultimate fate of CO and O2 produced in such atmospheres is strongly dependent on the imposed lower boundary condition, with low depositional velocities corresponding to higher mixing ratios in the lower atmosphere. The deposition velocity of a gas depends on it dissolved concentration, however, and so one needs to consider the chemistry of these gases in solution. Ongoing work seeks to test the conclusions of Tian et al., (2013) by exploring this dependence on ocean chemistry and by including spectra from AD Leo (an active M-dwarf, used by Domagal-Goldman et al., (2011)) to compare with the M-dwarf spectra used by Tian et al.

  9. Plastic condom developed.

    PubMed

    1992-01-01

    A prototype plastic condom that is expected to be at least as strong as latex, less likely to fail, and more comfortable to use has been designed by researchers at North Carolina-based Family Health International (FHI). The National Institutes of Health has granted the nonprofit medical research organization $1.3 million to conduct tests that will include clinical trials involving volunteer couples to examine the condom/s safety, efficacy in preventing pregnancy, and acceptability among users. Researchers hope the tests, expected to take about 4 years, will show that the plastic condom can be stored for years without weakening, whereas latex loses strength with time. In addition, FHI claims the plastic condom can be used with any kind of lubricant, while Latex is limited to water-based or silicone lubricants. Latex condoms lose up to 90% of their strength when used with oil-based lubricants such as hand lotion, according to studies.

  10. Consumer hazards of plastics.

    PubMed Central

    Wiberg, G S

    1976-01-01

    The modern consumer is exposed to a wide variety of plastic and rubber products in his day to day life: at home, work, school, shopping, recreation and play, and transport. A large variety of toxic sequellae have resulted from untoward exposures by many different routes: oral, dermal, inhalation, and parenteral. Toxic change may result from the plastic itself, migration of unbound components and additives, chemical decomposition or toxic pyrolysis products. The type of damage may involve acute poisoning, chronic organ damage, reproductive disorders, and carcinogenic, mutagenic and teratogenic episodes. Typical examples for all routes are cited along with the activites of Canadian regulatory agencies to reduce both the incidence and severity of plastic-induced disease. PMID:1026409

  11. Adaptation without Plasticity.

    PubMed

    Del Mar Quiroga, Maria; Morris, Adam P; Krekelberg, Bart

    2016-09-27

    Sensory adaptation is a phenomenon in which neurons are affected not only by their immediate input but also by the sequence of preceding inputs. In visual cortex, for example, neurons shift their preferred orientation after exposure to an oriented stimulus. This adaptation is traditionally attributed to plasticity. We show that a recurrent network generates tuning curve shifts observed in cat and macaque visual cortex, even when all synaptic weights and intrinsic properties in the model are fixed. This demonstrates that, in a recurrent network, adaptation on timescales of hundreds of milliseconds does not require plasticity. Given the ubiquity of recurrent connections, this phenomenon likely contributes to responses observed across cortex and shows that plasticity cannot be inferred solely from changes in tuning on these timescales. More broadly, our findings show that recurrent connections can endow a network with a powerful mechanism to store and integrate recent contextual information. PMID:27681421

  12. Generalized site occupancy models allowing for false positive and false negative errors

    USGS Publications Warehouse

    Royle, J. Andrew; Link, W.A.

    2006-01-01

    Site occupancy models have been developed that allow for imperfect species detection or ?false negative? observations. Such models have become widely adopted in surveys of many taxa. The most fundamental assumption underlying these models is that ?false positive? errors are not possible. That is, one cannot detect a species where it does not occur. However, such errors are possible in many sampling situations for a number of reasons, and even low false positive error rates can induce extreme bias in estimates of site occupancy when they are not accounted for. In this paper, we develop a model for site occupancy that allows for both false negative and false positive error rates. This model can be represented as a two-component finite mixture model and can be easily fitted using freely available software. We provide an analysis of avian survey data using the proposed model and present results of a brief simulation study evaluating the performance of the maximum-likelihood estimator and the naive estimator in the presence of false positive errors.

  13. 'Endurance Crater's' Dazzling Dunes (false-color)

    NASA Technical Reports Server (NTRS)

    2004-01-01

    As NASA's Mars Exploration Rover Opportunity creeps farther into 'Endurance Crater,' the dune field on the crater floor appears even more dramatic. This false-color image taken by the rover's panoramic camera shows that the dune crests have accumulated more dust than the flanks of the dunes and the flat surfaces between them. Also evident is a 'blue' tint on the flat surfaces as compared to the dune flanks. This results from the presence of the hematite-containing spherules ('blueberries') that accumulate on the flat surfaces.

    Sinuous tendrils of sand less than 1 meter (3.3 feet) high extend from the main dune field toward the rover. Scientists hope to send the rover down to one of these tendrils in an effort to learn more about the characteristics of the dunes. Dunes are a common feature across the surface of Mars, and knowledge gleaned from investigating the Endurance dunes close-up may apply to similar dunes elsewhere.

    Before the rover heads down to the dunes, rover drivers must first establish whether the slippery slope that leads to them is firm enough to ensure a successful drive back out of the crater. Otherwise, such hazards might make the dune field a true sand trap.

  14. Possible and False Biomarkers from Space

    NASA Technical Reports Server (NTRS)

    Bernstein, Max P.

    2004-01-01

    The Search for life in the Solar System is one of NASA's main goals for the coming decade. We may never observe alien life directly; we or our robotic craft may always be removed from it by many years, or meters of crust. If we do find evidence of Life elsewhere in the Solar System it will probably be in form of chemical biomarkers, quintessentially biological molecules that indicate the presence of micro-organisms. What molecules would be truly indicative of alien life? Chlorophyll fragments, which are often used by geochemists are probably far too specific. Simpler molecules, such as fatty acids, amino acids and nucleo-bases might seem to be biomarkers, but they can form non-biotically in space. Alkyl substituted aromatics in ALH 84001 have been invoked as biomarkers, but they are not strong evidence in and of themselves. Understanding the range of nonbiological organic molecules which could act as false biomarkers in space is a prerequisite for any reasonable search for true biomarkers on other worlds. When simple organics arrive at the surface of a body like Europa, either from below or from space, how long do they survive and what do they make? How can we distinguish these from real biomarkers? In this talk I will present some ideas about what might be useful qualities to consider in a potential biomarker, and will ask for advice from the attendant geochemists.

  15. False-color composite of Oetztal, Austria

    NASA Technical Reports Server (NTRS)

    1994-01-01

    This image is a false-color composite of Oetztal, Austria located in the Central Alps centered at 46.8 degrees north latitude, 10.70 degrees east longitude, at the border between Switzerland (top), Italy (left) and Austria (right and bottom). The area shown is 50 kilometers (30 miles) south of Inssbruck, Austria. This image was acquired by the Spaceborne Imaging Radar-C/X-band Synthetic Aperature Radar (SIR-C/X-SAR) flying on the Space Shuttle Endeavour on its 14th orbit. Approximately one quarter of this image is covered by glaciers, the largest of which, Gepatschferner, is visible as a triangular yellow patch in the center of the scene. The blue areas are lakes (Gepatsch dam at center right; Lake Muta at top right) and glacier ice. The yellow areas are slopes facing the radar and areas of dry snow. Purple corresponds to slopes facing away from the radar. Yellow in the valley bottom corresponds to tree covered areas. The Jet Propulsion Laboratory alternative photo number is P-43890.

  16. Deep Hole in 'Clovis' (False Color)

    NASA Technical Reports Server (NTRS)

    2004-01-01

    At a rock called 'Clovis,' the rock abrasion tool on NASA's Mars Exploration Rover Spirit cut a 9-millimeter (0.35-inch) hole during the rover's 216th martian day, or sol (Aug. 11, 2004). The hole is the deepest drilled in a rock on Mars so far. This false color view was made from images taken by Spirit's panoramic camera on sol 226 (Aug. 21, 2004) at around 12:50 p.m. local true solar time -- early afternoon in Gusev Crater on Mars. To the right is a 'brush flower' of circles produced by scrubbing the surface of the rock with the abrasion tool's wire brush. Scientists used rover's Moessbauer spectrometer and alpha particle X-ray spectrometer to look for iron-bearing minerals and determine the elemental chemical composition of the rock. This composite combines images taken with the camera's 750-, 530-, and 430-nanometer filters. The grayish-blue hue in this image suggests that the interior of the rock contains iron minerals that are less oxidized than minerals on the surface. The diameter of the hole cut into the rock is 4.5 centimeters (1.8 inches).

  17. Frog Swarms: Earthquake Precursors or False Alarms?

    PubMed Central

    Grant, Rachel A.; Conlan, Hilary

    2013-01-01

    Simple Summary Media reports linking unusual animal behaviour with earthquakes can potentially create false alarms and unnecessary anxiety among people that live in earthquake risk zones. Recently large frog swarms in China and elsewhere have been reported as earthquake precursors in the media. By examining international media reports of frog swarms since 1850 in comparison to earthquake data, it was concluded that frog swarms are naturally occurring dispersal behaviour of juveniles and are not associated with earthquakes. However, the media in seismic risk areas may be more likely to report frog swarms, and more likely to disseminate reports on frog swarms after earthquakes have occurred, leading to an apparent link between frog swarms and earthquakes. Abstract In short-term earthquake risk forecasting, the avoidance of false alarms is of utmost importance to preclude the possibility of unnecessary panic among populations in seismic hazard areas. Unusual animal behaviour prior to earthquakes has been reported for millennia but has rarely been scientifically documented. Recently large migrations or unusual behaviour of amphibians have been linked to large earthquakes, and media reports of large frog and toad migrations in areas of high seismic risk such as Greece and China have led to fears of a subsequent large earthquake. However, at certain times of year large migrations are part of the normal behavioural repertoire of amphibians. News reports of “frog swarms” from 1850 to the present day were examined for evidence that this behaviour is a precursor to large earthquakes. It was found that only two of 28 reported frog swarms preceded large earthquakes (Sichuan province, China in 2008 and 2010). All of the reported mass migrations of amphibians occurred in late spring, summer and autumn and appeared to relate to small juvenile anurans (frogs and toads). It was concluded that most reported “frog swarms” are actually normal behaviour, probably caused by

  18. Geophysics Fatally Flawed by False Fundamental Philosophy

    NASA Astrophysics Data System (ADS)

    Myers, L. S.

    2004-05-01

    For two centuries scientists have failed to realize Laplace's nebular hypothesis \\(1796\\) of Earth's creation is false. As a consequence, geophysicists today are misinterpreting and miscalculating many fundamental aspects of the Earth and Solar System. Why scientists have deluded themselves for so long is a mystery. The greatest error is the assumption Earth was created 4.6 billion years ago as a molten protoplanet in its present size, shape and composition. This assumption ignores daily accretion of more than 200 tons/day of meteorites and dust, plus unknown volumes of solar insolation that created coal beds and other biomass that increased Earth's mass and diameter over time! Although the volume added daily is minuscule compared with Earth's total mass, logic and simple addition mandates an increase in mass, diameter and gravity. Increased diameter from accretion is proved by Grand Canyon stratigraphy that shows a one kilometer increase in depth and planetary radius at a rate exceeding three meters \\(10 ft\\) per Ma from start of the Cambrian \\(540 Ma\\) to end of the Permian \\(245 Ma\\)-each layer deposited onto Earth's surface. This is unequivocal evidence of passive external growth by accretion, part of a dual growth and expansion process called "Accreation" \\(creation by accretion\\). Dynamic internal core expansion, the second stage of Accreation, did not commence until the protoplanet reached spherical shape at 500-600 km diameter. At that point, gravity-powered compressive heating initiated core melting and internal expansion. Expansion quickly surpassed the external accretion growth rate and produced surface volcanoes to relieve explosive internal tectonic pressure and transfer excess mass (magma)to the surface. Then, 200-250 Ma, expansion triggered Pangaea's breakup, first sundering Asia and Australia to form the Pacific Ocean, followed by North and South America to form the Atlantic Ocean, by the mechanism of midocean ridges, linear underwater

  19. Spirit View of 'Wishstone' (False Color)

    NASA Technical Reports Server (NTRS)

    2005-01-01

    [figure removed for brevity, see original site] Figure 1

    Scientists working with NASA's Mars Exploration Rover Spirit decided to examine this rock, dubbed 'Wishstone,' based on data from the miniature thermal emission spectrometer. That instrument's data indicated that the mineralogy of the rocks in this area is different from that of rocks encountered either on the plains of Gusev Crater or in bedrock outcrops examined so far in the 'Columbia Hills' inside the crater. Spirit used its rock abrasion tool first to scour a patch of the rock's surface with a wire brush, then to grind away the surface to reveal interior material. Placement of the rover's alpha particle X-ray spectrometer on the exposed circle of interior material revealed that the rock is rich in phosphorus. Spirit used its panoramic camera during the rover's 342nd martian day, or sol, (Dec. 18, 2004) to take the three individual images that were combined to produce this false-color view emphasizing the freshly ground dust around the hole cut by the rock abrasion tool.

    Unusually Rich in Phosophorus The graph in figure 1 compares the elemental makeup of a rock dubbed 'Wishstone' with the average composition of rocks that Spirit examined on the western spur of the 'Columbia Hills.' Wishstone lies farther into the hills than that spur. It is richer in phosphorus than any other Mars rock ever examined. Scientists plan to examine other rocks near Wishstone to help explain the significance of the high phosphorus concentration. The vertical scale is the ratio of the concentration of an element in the hills rocks to the concentration of the same element in a typical volcanic rock from the plains that Spirit crossed to reach the hills.

  20. Venus - False Color of Bereghinya Planitia

    NASA Technical Reports Server (NTRS)

    1992-01-01

    This false color Magellan image shows a portion of Bereghinya Planitia (plains) in the northern hemisphere of Venus, centered at 31 degrees north latitude, 43 degrees east longitude. The area is 260 kilometers (160 miles) wide and 330 kilometers (200 miles) long. This image was produced from Magellan radar data collected in Cycle 2 of the mission. Cycle 2 was completed January 15, 1992. The area was not imaged during the first cycle because of superior conjunction when the sun was between the Earth and Venus, preventing communication with the spacecraft. This image contains examples of several of the major geologic terrains on Venus and illustrates the basic stratigraphy or sequence of geologic events. The oldest terrains appear as bright, highly-fractured or chaotic highlands rising out of the plains. This is seen in the upper right and lower left quadrants of the image. The chaotic highlands, sometimes called tessera, may represent older and thicker crustal material and occupy about 15 percent of the surface of Venus. Plains surround and embay the fractured highland tessera. Plains are formed by fluid volcanic flows that may have once formed vast lava seas which covered all the low lying surfaces. Plains comprise more than 80 percent of the surface of Venus. The most recent activity in the region is volcanism that produced the radar bright flows best seen in the lower right quadrant of the image. The lava flows in this image are associated with the shield volcano Tepev Mons whose summit is near the lower left corner of the image. The flows are similar to the darker plains volcanics, but apparently have more rugged surfaces that more efficiently scatter the radar signal back to the spacecraft. The geologic sequence is early fracturing of the tessera, flooding by extensive plains lavas and scattered, less extensive individual flows on the plains surface. The simulated hues are based on color images recorded by the Soviet Venera 13 and 14 spacecraft.

  1. A Frosty Rim In False Color

    NASA Technical Reports Server (NTRS)

    2005-01-01

    [figure removed for brevity, see original site]

    The theme for the weeks of 1/17 and 1/24 is the north polar region of Mars as seen in false color THEMIS images. Ice/frost will typically appear as bright blue in color; dust mantled ice will appear in tones of red/orange.

    Our final image combines the features of the past two days, with a dust covered frosty crater rim and the bluer sand dunes of the north polar region.

    Image information: VIS instrument. Latitude 70.1, Longitude 351.8 East (8.2 West). 40 meter/pixel resolution.

    Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time.

    NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space Science, Washington, D.C. The Thermal Emission Imaging System (THEMIS) was developed by Arizona State University, Tempe, in collaboration with Raytheon Santa Barbara Remote Sensing. The THEMIS investigation is led by Dr. Philip Christensen at Arizona State University. Lockheed Martin Astronautics, Denver, is the prime contractor for the Odyssey project, and developed and built the orbiter. Mission operations are conducted jointly from Lockheed Martin and from JPL, a division of the California Institute of Technology in Pasadena.

  2. Natural and False Color Views of Europa

    NASA Technical Reports Server (NTRS)

    1996-01-01

    This image shows two views of the trailing hemisphere of Jupiter's ice-covered satellite, Europa. The left image shows the approximate natural color appearance of Europa. The image on the right is a false-color composite version combining violet, green and infrared images to enhance color differences in the predominantly water-ice crust of Europa. Dark brown areas represent rocky material derived from the interior, implanted by impact, or from a combination of interior and exterior sources. Bright plains in the polar areas (top and bottom) are shown in tones of blue to distinguish possibly coarse-grained ice (dark blue) from fine-grained ice (light blue). Long, dark lines are fractures in the crust, some of which are more than 3,000 kilometers (1,850 miles) long. The bright feature containing a central dark spot in the lower third of the image is a young impact crater some 50 kilometers (31 miles) in diameter. This crater has been provisionally named 'Pwyll' for the Celtic god of the underworld.

    Europa is about 3,160 kilometers (1,950 miles) in diameter, or about the size of Earth's moon. This image was taken on September 7, 1996, at a range of 677,000 kilometers (417,900 miles) by the solid state imaging television camera onboard the Galileo spacecraft during its second orbit around Jupiter. The image was processed by Deutsche Forschungsanstalt fuer Luftund Raumfahrt e.V., Berlin, Germany.

    The Jet Propulsion Laboratory, Pasadena, CA, manages the mission for NASA's Office of Space Science, Washington, DC.

    This image and other images and data received from Galileo are posted on the Galileo mission home page on the World Wide Web at http://galileo.jpl.nasa.gov. Background information and educational context for the images can be found at http://www.jpl.nasa.gov/galileo/sepo

  3. Blind sequential lineup administration reduces both false identifications and confidence in those false identifications.

    PubMed

    Charman, Steve D; Quiroz, Vanessa

    2016-10-01

    One of the most recommended procedures proposed by eyewitness experts is the use of double-blind lineups, in which the administrator does not know the identity of the suspect in the lineup. But despite the near universality of this recommendation, there is surprisingly little empirical research to support the claim that nonblind administration inflates false identifications. What little research has been conducted has shown conflicting findings with regard to the conditions under which nonblind administration affects false identifications, as well as its effects on witness confidence. The current study attempts to elucidate this effect. Student-participants (n = 312) were randomly assigned to play the role of either a lineup administrator (who were either told the identity of the suspect in the lineup or not) or a mock crime witness. Following unbiased instructions, administrators presented either a target-present or target-absent sequential lineup to the witness while being surreptitiously videorecorded. Nonblind administration significantly inflated false, but not correct, identifications, and significantly inflated witness confidence in those false identifications. Video recordings indicated that nonblind administrators were significantly more likely than blind administrators to smile (a) while the witness was viewing a photograph of the suspect, and (b) after a suspect identification. Results provide stronger support for the use of blind lineup administration by broadening the conditions under which nonblind administration is shown to inflate false identifications. Possible reconciliations for conflicting findings in the literature are discussed. (PsycINFO Database Record

  4. Skin sensitization, false positives and false negatives: experience with guinea pig assays.

    PubMed

    Basketter, David A; Kimber, Ian

    2010-07-01

    The advent of the local lymph node assay (LLNA), and efforts to develop in vitro alternatives for the identification of skin sensitizing chemicals has focused attention on the issue of false positive and false negative results. In essence, the question becomes 'what is the gold standard?' In this context, attention has focused primarily on the LLNA as this is now the preferred assay for skin sensitization testing. However, for many years prior to introduction of the LLNA, the guinea pig maximization test and the occluded patch test of Buehler were the methods of choice. In order to encourage a more informed dialogue about the relative performance, accuracy and applicability of the LLNA and guinea pig tests, we have here considered the extent to which guinea pig methods were themselves subject to false positives and negative results. We describe and discuss here well-characterized examples of instances where both false negatives (including abietic acid and eugenol) or false positives (including vanillin and sulfanilic acid) have been recorded in guinea pig tests. These and other examples are discussed with particular reference to the fabrication of a gold standard dataset that is required for the validation of in vitro alternatives.

  5. Plastics in Perspective.

    ERIC Educational Resources Information Center

    Bergandine, David R.; Holm, D. Andrew

    The materials in this curriculum supplement, developed for middle school or high school science classes, present solid waste problems related to plastics. The set of curriculum materials is divided into two units to be used together or independently. Unit I begins by comparing patterns in solid waste from 1960 to 1990 and introducing methods for…

  6. Hydrodynamic Elastic Magneto Plastic

    1985-02-01

    The HEMP code solves the conservation equations of two-dimensional elastic-plastic flow, in plane x-y coordinates or in cylindrical symmetry around the x-axis. Provisions for calculation of fixed boundaries, free surfaces, pistons, and boundary slide planes have been included, along with other special conditions.

  7. Spirit's West Valley Panorama (False Color)

    NASA Technical Reports Server (NTRS)

    2008-01-01

    NASA'S Mars Exploration Rover Spirit captured this westward view from atop a low plateau where Sprit spent the closing months of 2007.

    After several months near the base of the plateau called 'Home Plate' in the inner basin of the Columbia Hills range inside Gusev Crater, Spirit climbed onto the eastern edge of the plateau during the rover's 1,306th Martian day, or sol, (Sept. 5, 2007). It examined rocks and soils at several locations on the southern half of Home Plate during September and October. It was perched near the western edge of Home Plate when it used its panoramic camera (Pancam) to take the images used in this view on sols 1,366 through 1,369 (Nov. 6 through Nov. 9, 2007). With its daily solar-energy supply shrinking as Martian summer turned to fall, Spirit then drove to the northern edge of Home Plate for a favorable winter haven. The rover reached that northward-tilting site in December, in time for the fourth Earth-year anniversary of its landing on Mars. Spirit reached Mars on Jan. 4, 2004, Universal Time (Jan. 3, 2004, Pacific Standard Time). It landed at a site at about the center of the horizon in this image.

    This panorama covers a scene spanning left to right from southwest to northeast. The western edge of Home Plate is in the foreground, generally lighter in tone than the more distant parts of the scene. A rock-dotted hill in the middle distance across the left third of the image is 'Tsiolkovski Ridge,' about 30 meters or 100 feet from the edge of Home Plate and about that same distance across. A bump on the horizon above the left edge of Tsiolkovski Ridge is 'Grissom Hill,' about 8 kilometers or 5 miles away. At right, the highest point of the horizon is 'Husband Hill,' to the north and about 800 meters or half a mile away.

    This view combines separate images taken through Pancam filters centered on wavelengths of 753 nanometers, 535 nanometers and 432 nanometers. It is presented in a false-color stretch to bring out subtle

  8. 'Lyell' Panorama inside Victoria Crater (False Color)

    NASA Technical Reports Server (NTRS)

    2008-01-01

    During four months prior to the fourth anniversary of its landing on Mars, NASA's Mars Exploration Rover Opportunity examined rocks inside an alcove called 'Duck Bay' in the western portion of Victoria Crater. The main body of the crater appears in the upper right of this stereo panorama, with the far side of the crater lying about 800 meters (half a mile) away. Bracketing that part of the view are two promontories on the crater's rim at either side of Duck Bay. They are 'Cape Verde,' about 6 meters (20 feet) tall, on the left, and 'Cabo Frio,' about 15 meters (50 feet) tall, on the right. The rest of the image, other than sky and portions of the rover, is ground within Duck Bay.

    Opportunity's targets of study during the last quarter of 2007 were rock layers within a band exposed around the interior of the crater, about 6 meters (20 feet) from the rim. Bright rocks within the band are visible in the foreground of the panorama. The rover science team assigned informal names to three subdivisions of the band: 'Steno,' 'Smith,' and 'Lyell.'

    This view combines many images taken by Opportunity's panoramic camera (Pancam) from the 1,332nd through 1,379th Martian days, or sols, of the mission (Oct. 23 to Dec. 11, 2007). Images taken through Pancam filters centered on wavelengths of 753 nanometers, 535 nanometers and 432 nanometers were mixed to produce this view, which is presented in a false-color stretch to bring out subtle color differences in the scene. Some visible patterns in dark and light tones are the result of combining frames that were affected by dust on the front sapphire window of the rover's camera.

  9. False Color Mosaic Great Red Spot

    NASA Technical Reports Server (NTRS)

    1996-01-01

    False color representation of Jupiter's Great Red Spot (GRS) taken through three different near-infrared filters of the Galileo imaging system and processed to reveal cloud top height. Images taken through Galileo's near-infrared filters record sunlight beyond the visible range that penetrates to different depths in Jupiter's atmosphere before being reflected by clouds. The Great Red Spot appears pink and the surrounding region blue because of the particular color coding used in this representation. Light reflected by Jupiter at a wavelength (886 nm) where methane strongly absorbs is shown in red. Due to this absorption, only high clouds can reflect sunlight in this wavelength. Reflected light at a wavelength (732 nm) where methane absorbs less strongly is shown in green. Lower clouds can reflect sunlight in this wavelength. Reflected light at a wavelength (757 nm) where there are essentially no absorbers in the Jovian atmosphere is shown in blue: This light is reflected from the deepest clouds. Thus, the color of a cloud in this image indicates its height. Blue or black areas are deep clouds; pink areas are high, thin hazes; white areas are high, thick clouds. This image shows the Great Red Spot to be relatively high, as are some smaller clouds to the northeast and northwest that are surprisingly like towering thunderstorms found on Earth. The deepest clouds are in the collar surrounding the Great Red Spot, and also just to the northwest of the high (bright) cloud in the northwest corner of the image. Preliminary modeling shows these cloud heights vary over 30 km in altitude. This mosaic, of eighteen images (6 in each filter) taken over a 6 minute interval during the second GRS observing sequence on June 26, 1996, has been map-projected to a uniform grid of latitude and longitude. North is at the top.

    Launched in October 1989, Galileo entered orbit around Jupiter on December 7, 1995. The spacecraft's mission is to conduct detailed studies of the giant planet

  10. False Color Image of Volcano Sapas Mons

    NASA Technical Reports Server (NTRS)

    1991-01-01

    This false-color image shows the volcano Sapas Mons, which is located in the broad equatorial rise called Atla Regio (8 degrees north latitude and 188 degrees east longitude). The area shown is approximately 650 kilometers (404 miles) on a side. Sapas Mons measures about 400 kilometers (248 miles) across and 1.5 kilometers (0.9 mile) high. Its flanks show numerous overlapping lava flows. The dark flows on the lower right are thought to be smoother than the brighter ones near the central part of the volcano. Many of the flows appear to have been erupted along the flanks of the volcano rather than from the summit. This type of flank eruption is common on large volcanoes on Earth, such as the Hawaiian volcanoes. The summit area has two flat-topped mesas, whose smooth tops give a relatively dark appearance in the radar image. Also seen near the summit are groups of pits, some as large as one kilometer (0.6 mile) across. These are thought to have formed when underground chambers of magma were drained through other subsurface tubes and lead to a collapse at the surface. A 20 kilometer-diameter (12-mile diameter) impact crater northeast of the volcano is partially buried by the lava flows. Little was known about Atla Regio prior to Magellan. The new data, acquired in February 1991, show the region to be composed of at least five large volcanoes such as Sapas Mons, which are commonly linked by complex systems of fractures or rift zones. If comparable to similar features on Earth, Atla Regio probably formed when large volumes of molten rock upwelled from areas within the interior of Venus known as'hot spots.' Magellan is a NASA spacecraft mission to map the surface of Venus with imaging radar. The basic scientific instrument is a synthetic aperture radar, or SAR, which can look through the thick clouds perpetually shielding the surface of Venus. Magellan is in orbit around Venus which completes one turn around its axis in 243 Earth days. That period of time, one Venus day

  11. Panorama from 'Cape Verde' (False Color)

    NASA Technical Reports Server (NTRS)

    2007-01-01

    NASA's Mars Exploration Rover Opportunity captured this vista of 'Victoria Crater' from the viewpoint of 'Cape Verde,' one of the promontories that are part of the scalloped rim of the crater. Opportunity drove onto Cape Verde shortly after arriving at the rim of Victoria in September 2006. The view combines hundreds of exposures taken by the rover's panoramic camera (Pancam). The camera began taking the component images during Opportunity's 970th Martian day, or sol, on Mars (Oct. 16, 2006). Work on the panorama continued through the solar conjunction period, when Mars was nearly behind the sun from Earth's perspective and communications were minimized. Acquisition of images for this panorama was completed on Opportunity's 991st sol (Nov. 7, 2006).

    The top of Cape Verde is in the immediate foreground at the center of the image. To the left and right are two of the more gradually sloped bays that alternate with the cliff-faced capes or promontories around the rim of the crater. 'Duck Bay,' where Opportunity first reached the rim, is to the right. Beyond Duck Bay counterclockwise around the rim, the next promontory is 'Cabo Frio,' about 150 meters (500 feet) from the rover. On the left side of the panorama is 'Cape St. Mary,' the next promontory clockwise from Cape Verde and about 40 meters (130 feet) from the rover. The vantage point atop Cape Verde offered a good view of the rock layers in the cliff face of Cape St. Mary, which is about 15 meters or 50 feet tall. By about two weeks after the Pancam finished collecting the images for this panorama, Opportunity had driven to Cape St. Mary and was photographing Cape Verde's rock layers.

    The far side of the crater lies about 800 meters (half a mile) away, toward the southeast.

    This view combines images taken through three of the Pancam's filters, admitting light with wavelengths centered at 750 nanometers (near infrared), 530 nanometers (green) and 430 nanometers (violet). It is presented in false

  12. Plastics for Elementary School Children

    ERIC Educational Resources Information Center

    Hanson, Jack

    1977-01-01

    Describes three plastics projects (which involve making a styrene fishing bobber, an acrylic salad fork and spoon set, and acetate shrink art) designed to provide elementary level students an opportunity to work with plastics and to learn about careers in plastics production and distribution. (TA)

  13. Seabirds and floating plastic debris.

    PubMed

    Cadée, Gerhard C

    2002-11-01

    80% of floating plastic debris freshly washed ashore on a Dutch coast showed peckmarks made by birds at sea. They either mistake these debris for cuttlebones or simply test all floating objects. Ingestion of plastic is deleterious for marine organisms. It is urgent to set measures to plastic litter production.

  14. Gusev Rocks Solidified from Lava (False Color)

    NASA Technical Reports Server (NTRS)

    2006-01-01

    to identify rocks and features investigated by Spirit during the Chinese New Year celebration period. In ancient Chinese myth, FuYi was the first great emperor and lived in the east. He explained the theory of 'Yin' and 'Yang' to his people, invented the net to catch fish, was the first to use fire to cook food, and invented a musical instrument known as the 'Se' to accompany his peoples' songs and dances. Other rocks and features are being informally named for Chinese gods, warriors, inventors, and scientists, as well as rivers, lakes, and mountains.

    Spirit took this image on the rover's Martian day, or sol, 731 (Jan. 23, 2006). This is a false-color composite combining images taken with the Pancam's 750-nanometer, 530-nanometer and 430-nanometer filters.

  15. Screening for possible human carcinogens and mutagens. False positives, false negatives: statistical implications.

    PubMed

    Lovell, D P

    1989-07-01

    A screening method aimed at identifying potential human carcinogens using either animal cancer bioassays or short-term genotoxic assays has 4 possible results: true positive, true negative, false positive and false negative. Such a categorisation is superficially similar to the results of hypothesis testing in a statistical analysis. In this latter case the false positive rate is determined by the significance level of the test and the false negative rate by the statistical power of the test. Although the two types of categorisation appear somewhat similar, different statistical issues are involved in their interpretation. Statistical methods appropriate for the analysis of the results of a series of assays include the use of Bayes' theorem and multivariate methods such as clustering techniques for the selection of batteries of short-term test capable of a better prediction of potential carcinogens. The conclusions drawn from such studies are dependent upon the estimates of values of sensitivity and specificity used, the choice of statistical method and the nature of the data set. The statistical issues resulting from the analysis of specific genotoxicity experiments involve the choice of suitable experimental designs and appropriate analyses together with the relationship of statistical significance to biological importance. The purpose of statistical analysis should increasingly be to estimate and explore effects rather than for formal hypothesis testing.

  16. Breathing: Rhythmicity, Plasticity, Chemosensitivity

    PubMed Central

    Feldman, Jack L.; Mitchell, Gordon S.; Nattie, Eugene E.

    2010-01-01

    Breathing is a vital behavior that is particularly amenable to experimental investigation. We review recent progress on three problems of broad interest. (i) Where and how is respiratory rhythm generated? The preBötzinger Complex is a critical site, whereas pacemaker neurons may not be essential. The possibility that coupled oscillators are involved is considered. (ii) What are the mechanisms that underlie the plasticity necessary for adaptive changes in breathing? Serotonin-dependent long-term facilitation following intermittent hypoxia is an important example of such plasticity, and a model that can account for this adaptive behavior is discussed. (iii) Where and how are the regulated variables CO2 and pH sensed? These sensors are essential if breathing is to be appropriate for metabolism. Neurons with appropriate chemosensitivity are spread throughout the brainstem; their individual properties and collective role are just beginning to be understood. PMID:12598679

  17. Stress-gradient plasticity

    PubMed Central

    Chakravarthy, Srinath S.; Curtin, W. A.

    2011-01-01

    A new model, stress-gradient plasticity, is presented that provides unique mechanistic insight into size-dependent phenomena in plasticity. This dislocation-based model predicts strengthening of materials when a gradient in stress acts over dislocation source–obstacle configurations. The model has a physical length scale, the spacing of dislocation obstacles, and is validated by several levels of discrete-dislocation simulations. When incorporated into a continuum viscoplastic model, predictions for bending and torsion in polycrystalline metals show excellent agreement with experiments in the initial strengthening and subsequent hardening as a function of both sample-size dependence and grain size, when the operative obstacle spacing is proportional to the grain size. PMID:21911403

  18. Dodging the Dilemma of True-False Testing

    ERIC Educational Resources Information Center

    Eakin, Richard R.; Long, Clifford A.

    1977-01-01

    A scoring technique for true-false tests is presented. The technique, paired item scoring, involves combining two statements and having the student select one of the four resultants possible: true-true, false-true, true-false, and false-false. The combined item is treated as a multiple choice item. (Author/JKS)

  19. Compensatory plasticity: time matters.

    PubMed

    Lazzouni, Latifa; Lepore, Franco

    2014-01-01

    Plasticity in the human and animal brain is the rule, the base for development, and the way to deal effectively with the environment for making the most efficient use of all the senses. When the brain is deprived of one sensory modality, plasticity becomes compensatory: the exception that invalidates the general loss hypothesis giving the opportunity of effective change. Sensory deprivation comes with massive alterations in brain structure and function, behavioral outcomes, and neural interactions. Blind individuals do as good as the sighted and even more, show superior abilities in auditory, tactile and olfactory processing. This behavioral enhancement is accompanied with changes in occipital cortex function, where visual areas at different levels become responsive to non-visual information. The intact senses are in general used more efficiently in the blind but are also used more exclusively. New findings are disentangling these two aspects of compensatory plasticity. What is due to visual deprivation and what is dependent on the extended use of spared modalities? The latter seems to contribute highly to compensatory changes in the congenitally blind. Short-term deprivation through the use of blindfolds shows that cortical excitability of the visual cortex is likely to show rapid modulatory changes after few minutes of light deprivation and therefore changes are possible in adulthood. However, reorganization remains more pronounced in the congenitally blind. Cortico-cortical pathways between visual areas and the areas of preserved sensory modalities are inhibited in the presence of vision, but are unmasked after loss of vision or blindfolding as a mechanism likely to drive cross-modal information to the deafferented visual cortex. The development of specialized higher order visual pathways independently from early sensory experience is likely to preserve their function and switch to the intact modalities. Plasticity in the blind is also accompanied with

  20. Frozen cultural plasticity.

    PubMed

    Houdek, Petr; Novakova, Julie

    2016-01-01

    We discuss cultural group selection under the view of the frozen plasticity theory and the different explanatory power and predictions of this framework. We present evidence that cultural adaptations and their influence on the degree of cooperation may be more complex than presented by Richerson et al., and conclude with the gene-environment-culture relationship and its impacts on cultural group selection. PMID:27561647

  1. Plasticity of amyloid fibrils†

    PubMed Central

    Wetzel, Ronald; Shivaprasad, Shankaramma; Williams, Angela D.

    2008-01-01

    In experiments designed to characterize the basis of amyloid fibril stability through mutational analysis of the Aβ(1-40) molecule, fibrils exhibit consistent, significant structural malleability. In these results, and in other properties, amyloid fibrils appear to more resemble plastic materials generated from synthetic polymers than they do globular proteins. Thus, like synthetic polymers and plastics, amyloid fibrils exhibit both polymorphism, the ability of one polypeptide to form aggregates of different morphologies, and isomorphism, the ability of different polypeptides to grow into a fibrillar amyloid morphology. This view links amyloid with the prehistorical and 20th Century use of proteins as starting materials to make films, fibers, and plastics, and with the classic protein fiber stretching experiments of the Astbury group. Viewing amyloid from the point of view of the polymer chemist may shed new light on issues such as the role of protofibrils in the mechanism of amyloid formation, the biological potency of fibrils, and the prospects for discovering inhibitors of amyloid fibril formation. PMID:17198370

  2. Plastic footwear for leprosy.

    PubMed

    Antia, N H

    1990-03-01

    The anaesthetic foot in leprosy poses the most major problem in the rehabilitation of its patients. Various attempts have been made to produce protective footwear such as the microcellular rubber-car-tyre sandals. Unfortunately these attempts have had little success on a large scale because of the inability to produce them in large numbers and the stigma attached to such unusual footwear. While such footwear may be superior to the 'tennis' shoe in protecting the foot from injury by the penetration of sharp objects, it fails to distribute the weight-bearing forces which is the major cause of plantar damage and ulceration in the anaesthetic foot. This can be achieved by providing rigidity to the sole, as demonstrated by the healing of ulcers in plaster of paris casts or the rigid wooden clog. A new type of moulded plastic footwear has been evolved in conjunction with the plastic footwear industry which provides footwear that can be mass produced at a low price and which overcomes the stigma of leprosy. Controlled rigidity is provided by the incorporation of a spring steel shank between the sponge insole and the hard wearing plastic sole. Trials have demonstrated both the acceptability of the footwear and its protective effects as well as its hard wearing properties. PMID:2319903

  3. Microelectronics plastic molded packaging

    SciTech Connect

    Johnson, D.R.; Palmer, D.W.; Peterson, D.W.

    1997-02-01

    The use of commercial off-the-shelf (COTS) microelectronics for nuclear weapon applications will soon be reality rather than hearsay. The use of COTS for new technologies for uniquely military applications is being driven by the so-called Perry Initiative that requires the U.S. Department of Defense (DoD) to accept and utilize commercial standards for procurement of military systems. Based on this philosophy, coupled with several practical considerations, new weapons systems as well as future upgrades will contain plastic encapsulated microelectronics. However, a conservative Department of Energy (DOE) approach requires lifetime predictive models. Thus, the focus of the current project is on accelerated testing to advance current aging models as well as on the development of the methodology to be used during WR qualification of plastic encapsulated microelectronics. An additional focal point involves achieving awareness of commercial capabilities, materials, and processes. One of the major outcomes of the project has been the definition of proper techniques for handling and evaluation of modern surface mount parts which might be used in future systems. This program is also raising the familiarity level of plastic within the weapons complex, allowing subsystem design rules accommodating COTS to evolve. A two year program plan is presented along with test results and commercial interactions during this first year.

  4. Respiratory Muscle Plasticity

    PubMed Central

    Gransee, Heather M.; Mantilla, Carlos B.; Sieck, Gary C.

    2014-01-01

    Muscle plasticity is defined as the ability of a given muscle to alter its structural and functional properties in accordance with the environmental conditions imposed on it. As such, respiratory muscle is in a constant state of remodeling, and the basis of muscle’s plasticity is its ability to change protein expression and resultant protein balance in response to varying environmental conditions. Here, we will describe the changes of respiratory muscle imposed by extrinsic changes in mechanical load, activity, and innervation. Although there is a large body of literature on the structural and functional plasticity of respiratory muscles, we are only beginning to understand the molecular-scale protein changes that contribute to protein balance. We will give an overview of key mechanisms regulating protein synthesis and protein degradation, as well as the complex interactions between them. We suggest future application of a systems biology approach that would develop a mathematical model of protein balance and greatly improve treatments in a variety of clinical settings related to maintaining both muscle mass and optimal contractile function of respiratory muscles. PMID:23798306

  5. How the Sausage is Made: Kepler's False Alarms, False Positives, and Planet Candidates

    NASA Astrophysics Data System (ADS)

    Coughlin, J.

    2014-04-01

    The Kepler mission has now designated over 7,000 Kepler objects of interest (KOIs), or transit-like signatures, utilizing up to four years of data. The number of potentially habitable planet candidates (PCs) among this sample has risen significantly over time. However, starting with Kepler threshold crossing events (TCEs), there are initially about as many false alarms (FAs) detected as there are KOIs. Furthermore, due to its design, contamination from eclipsing binaries, variable stars, and other transiting planets result in a significant number of KOIs being designated as false positives (FPs). Many of these FAs and FPs occur at long orbital periods, where habitable planets are typically found. I will review the process of how an initial TCE becomes a KOI, and then is ultimately classified as a FA, FP, or PC, along with the various vetting tools employed. The understanding of this process is crucial to performing accurate statistical analyses on populations of habitable planet candidates discovered by Kepler.

  6. New perspectives in plastic biodegradation.

    PubMed

    Sivan, Alex

    2011-06-01

    During the past 50 years new plastic materials, in various applications, have gradually replaced the traditional metal, wood, leather materials. Ironically, the most preferred property of plastics--durability--exerts also the major environmental threat. Recycling has practically failed to provide a safe solution for disposal of plastic waste (only 5% out of 1 trillion plastic bags, annually produced in the US alone, are being recycled). Since the most utilized plastic is polyethylene (PE; ca. 140 million tons/year), any reduction in the accumulation of PE waste alone would have a major impact on the overall reduction of the plastic waste in the environment. Since PE is considered to be practically inert, efforts were made to isolate unique microorganisms capable of utilizing synthetic polymers. Recent data showed that biodegradation of plastic waste with selected microbial strains became a viable solution.

  7. False Memory ≠ False Memory: DRM Errors Are Unrelated to the Misinformation Effect

    PubMed Central

    Ost, James; Blank, Hartmut; Davies, Joanna; Jones, Georgina; Lambert, Katie; Salmon, Kelly

    2013-01-01

    The DRM method has proved to be a popular and powerful, if controversial, way to study ‘false memories’. One reason for the controversy is that the extent to which the DRM effect generalises to other kinds of memory error has been neither satisfactorily established nor subject to much empirical attention. In the present paper we contribute data to this ongoing debate. One hundred and twenty participants took part in a standard misinformation effect experiment, in which they watched some CCTV footage, were exposed to misleading post-event information about events depicted in the footage, and then completed free recall and recognition tests. Participants also completed a DRM test as an ostensibly unrelated filler task. Despite obtaining robust misinformation and DRM effects, there were no correlations between a broad range of misinformation and DRM effect measures (mean r  = −.01). This was not due to reliability issues with our measures or a lack of power. Thus DRM ‘false memories’ and misinformation effect ‘false memories’ do not appear to be equivalent. PMID:23573186

  8. Balancing false positives and false negatives for the detection of differential expression in malignancies

    PubMed Central

    De Smet, F; Moreau, Y; Engelen, K; Timmerman, D; Vergote, I; De Moor, B

    2004-01-01

    A basic problem of microarray data analysis is to identify genes whose expression is affected by the distinction between malignancies with different properties. These genes are said to be differentially expressed. Differential expression can be detected by selecting the genes with P-values (derived using an appropriate hypothesis test) below a certain rejection level. This selection, however, is not possible without accepting some false positives and negatives since the two sets of P-values, associated with the genes whose expression is and is not affected by the distinction between the different malignancies, overlap. We describe a procedure for the study of differential expression in microarray data based on receiver-operating characteristic curves. This approach can be useful to select a rejection level that balances the number of false positives and negatives and to assess the degree of overlap between the two sets of P-values. Since this degree of overlap characterises the balance that can be reached between the number of false positives and negatives, this quantity can be seen as a quality measure of microarray data with respect to the detection of differential expression. As an example, we apply our method to data sets studying acute leukaemia. PMID:15354216

  9. Interfacial interactions between plastic particles in plastics flotation.

    PubMed

    Wang, Chong-qing; Wang, Hui; Gu, Guo-hua; Fu, Jian-gang; Lin, Qing-quan; Liu, You-nian

    2015-12-01

    Plastics flotation used for recycling of plastic wastes receives increasing attention for its industrial application. In order to study the mechanism of plastics flotation, the interfacial interactions between plastic particles in flotation system were investigated through calculation of Lifshitz-van der Waals (LW) function, Lewis acid-base (AB) Gibbs function, and the extended Derjaguin-Landau-Verwey-Overbeek potential energy profiles. The results showed that van der Waals force between plastic particles is attraction force in flotation system. The large hydrophobic attraction, caused by the AB Gibbs function, is the dominant interparticle force. Wetting agents present significant effects on the interfacial interactions between plastic particles. It is found that adsorption of wetting agents promotes dispersion of plastic particles and decreases the floatability. Pneumatic flotation may improve the recovery and purity of separated plastics through selective adsorption of wetting agents on plastic surface. The relationships between hydrophobic attraction and surface properties were also examined. It is revealed that there exists a three-order polynomial relationship between the AB Gibbs function and Lewis base component. Our finding provides some insights into mechanism of plastics flotation.

  10. Interfacial interactions between plastic particles in plastics flotation.

    PubMed

    Wang, Chong-qing; Wang, Hui; Gu, Guo-hua; Fu, Jian-gang; Lin, Qing-quan; Liu, You-nian

    2015-12-01

    Plastics flotation used for recycling of plastic wastes receives increasing attention for its industrial application. In order to study the mechanism of plastics flotation, the interfacial interactions between plastic particles in flotation system were investigated through calculation of Lifshitz-van der Waals (LW) function, Lewis acid-base (AB) Gibbs function, and the extended Derjaguin-Landau-Verwey-Overbeek potential energy profiles. The results showed that van der Waals force between plastic particles is attraction force in flotation system. The large hydrophobic attraction, caused by the AB Gibbs function, is the dominant interparticle force. Wetting agents present significant effects on the interfacial interactions between plastic particles. It is found that adsorption of wetting agents promotes dispersion of plastic particles and decreases the floatability. Pneumatic flotation may improve the recovery and purity of separated plastics through selective adsorption of wetting agents on plastic surface. The relationships between hydrophobic attraction and surface properties were also examined. It is revealed that there exists a three-order polynomial relationship between the AB Gibbs function and Lewis base component. Our finding provides some insights into mechanism of plastics flotation. PMID:26337962

  11. 46 CFR 26.30-1 - Approved unicellular plastic foam work vests.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 1 2011-10-01 2011-10-01 false Approved unicellular plastic foam work vests. 26.30-1 Section 26.30-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY UNINSPECTED VESSELS OPERATIONS Work Vest § 26.30-1 Approved unicellular plastic foam work vests. (a) Buoyant work vests carried under...

  12. 49 CFR 173.221 - Polymeric beads, expandable and Plastic molding compound.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Polymeric beads, expandable and Plastic molding... Than Class 1 and Class 7 § 173.221 Polymeric beads, expandable and Plastic molding compound. (a) Non-bulk shipments of Polymeric beads (or granules), expandable evolving flammable vapor and...

  13. 7 CFR 58.715 - Cream, plastic cream and anhydrous milkfat.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Cream, plastic cream and anhydrous milkfat. 58.715 Section 58.715 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING... Service 1 Quality Specifications for Raw Material § 58.715 Cream, plastic cream and anhydrous...

  14. 46 CFR 26.30-1 - Approved unicellular plastic foam work vests.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 1 2014-10-01 2014-10-01 false Approved unicellular plastic foam work vests. 26.30-1 Section 26.30-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY UNINSPECTED VESSELS OPERATIONS Work Vest § 26.30-1 Approved unicellular plastic foam work vests. (a) Buoyant work vests carried under...

  15. 49 CFR 173.221 - Polymeric beads, expandable and Plastic molding compound.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Polymeric beads, expandable and Plastic molding... Than Class 1 and Class 7 § 173.221 Polymeric beads, expandable and Plastic molding compound. (a) Non-bulk shipments of Polymeric beads (or granules), expandable, evolving flammable vapor and...

  16. 49 CFR 173.221 - Polymeric beads, expandable and Plastic molding compound.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Polymeric beads, expandable and Plastic molding... Than Class 1 and Class 7 § 173.221 Polymeric beads, expandable and Plastic molding compound. (a) Non-bulk shipments of Polymeric beads (or granules), expandable, evolving flammable vapor and...

  17. 49 CFR 173.221 - Polymeric beads, expandable and Plastic molding compound.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Polymeric beads, expandable and Plastic molding... Than Class 1 and Class 7 § 173.221 Polymeric beads, expandable and Plastic molding compound. (a) Non-bulk shipments of Polymeric beads (or granules), expandable evolving flammable vapor and...

  18. 7 CFR 58.715 - Cream, plastic cream and anhydrous milkfat.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Cream, plastic cream and anhydrous milkfat. 58.715 Section 58.715 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING... Service 1 Quality Specifications for Raw Material § 58.715 Cream, plastic cream and anhydrous...

  19. 24 CFR 3280.207 - Requirements for foam plastic thermal insulating materials.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Product Safety Commission requirements in 16 CFR parts 1209 and 1404. (2) Other loose-fill insulation that... 24 Housing and Urban Development 5 2014-04-01 2014-04-01 false Requirements for foam plastic... SAFETY STANDARDS Fire Safety § 3280.207 Requirements for foam plastic thermal insulating materials....

  20. 29 CFR 1910.216 - Mills and calenders in the rubber and plastics industries.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 5 2014-07-01 2014-07-01 false Mills and calenders in the rubber and plastics industries. 1910.216 Section 1910.216 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND... Guarding § 1910.216 Mills and calenders in the rubber and plastics industries. (a) General requirements—...

  1. 7 CFR 58.715 - Cream, plastic cream and anhydrous milkfat.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Cream, plastic cream and anhydrous milkfat. 58.715 Section 58.715 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING... Service 1 Quality Specifications for Raw Material § 58.715 Cream, plastic cream and anhydrous...

  2. 29 CFR 1910.216 - Mills and calenders in the rubber and plastics industries.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 29 Labor 5 2013-07-01 2013-07-01 false Mills and calenders in the rubber and plastics industries. 1910.216 Section 1910.216 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND... Guarding § 1910.216 Mills and calenders in the rubber and plastics industries. (a) General requirements—...

  3. 46 CFR 26.30-1 - Approved unicellular plastic foam work vests.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Approved unicellular plastic foam work vests. 26.30-1 Section 26.30-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY UNINSPECTED VESSELS OPERATIONS Work Vest § 26.30-1 Approved unicellular plastic foam work vests. (a) Buoyant work vests carried under...

  4. 7 CFR 58.715 - Cream, plastic cream and anhydrous milkfat.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Cream, plastic cream and anhydrous milkfat. 58.715 Section 58.715 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING... Service 1 Quality Specifications for Raw Material § 58.715 Cream, plastic cream and anhydrous...

  5. 46 CFR 26.30-1 - Approved unicellular plastic foam work vests.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 1 2013-10-01 2013-10-01 false Approved unicellular plastic foam work vests. 26.30-1 Section 26.30-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY UNINSPECTED VESSELS OPERATIONS Work Vest § 26.30-1 Approved unicellular plastic foam work vests. (a) Buoyant work vests carried under...

  6. 29 CFR 1910.216 - Mills and calenders in the rubber and plastics industries.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 5 2012-07-01 2012-07-01 false Mills and calenders in the rubber and plastics industries. 1910.216 Section 1910.216 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND... Guarding § 1910.216 Mills and calenders in the rubber and plastics industries. (a) General requirements—...

  7. 7 CFR 58.715 - Cream, plastic cream and anhydrous milkfat.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Cream, plastic cream and anhydrous milkfat. 58.715 Section 58.715 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING... Service 1 Quality Specifications for Raw Material § 58.715 Cream, plastic cream and anhydrous...

  8. 49 CFR 192.513 - Test requirements for plastic pipelines.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Test requirements for plastic pipelines. 192.513 Section 192.513 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE...

  9. 49 CFR 192.513 - Test requirements for plastic pipelines.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Test requirements for plastic pipelines. 192.513 Section 192.513 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE...

  10. 49 CFR 192.513 - Test requirements for plastic pipelines.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Test requirements for plastic pipelines. 192.513 Section 192.513 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE...

  11. 49 CFR 192.513 - Test requirements for plastic pipelines.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Test requirements for plastic pipelines. 192.513 Section 192.513 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE...

  12. False-evidence ploys and interrogations: mock jurors' perceptions of false-evidence ploy type, deception, coercion, and justification.

    PubMed

    Forrest, Krista D; Woody, William Douglas; Brady, Sara E; Batterman, Keller C; Stastny, Bradley J; Bruns, Jennifer A

    2012-01-01

    We studied mock jurors' evaluations of police false-evidence ploys across two false-evidence ploy information conditions (true or false confession). Study 1 participants evaluated lists of demeanor, testimonial, and scientific ploys and rated testimonial false-evidence ploys as more coercive than demeanor false-evidence ploys. Participants in the false-confession condition rated false-evidence ploys as more deceptive than did participants in the true-confession condition. Study 2 participants evaluated false-evidence ploy types within interrogation transcripts. Participants rated testimonial false-evidence ploys as more deceptive and coercive than demeanor false-evidence ploys; participants in the true-confession condition rated false-evidence ploys as more justified. Across studies, participants reading realistic transcripts rated false-evidence ploys as more deceptive and coercive. We discuss implications for scholars, attorneys, and interrogators. PMID:22315159

  13. Use of recycled plastics in wood plastic composites - a review.

    PubMed

    Kazemi Najafi, Saeed

    2013-09-01

    The use of recycled and waste thermoplastics has been recently considered for producing wood plastic composites (WPCs). They have great potential for WPCs manufacturing according to results of some limited researches. This paper presents a detailed review about some essential properties of waste and recycled plastics, important for WPCs production, and of research published on the effect of recycled plastics on the physical and mechanical properties of WPCs.

  14. Use of recycled plastics in wood plastic composites - a review.

    PubMed

    Kazemi Najafi, Saeed

    2013-09-01

    The use of recycled and waste thermoplastics has been recently considered for producing wood plastic composites (WPCs). They have great potential for WPCs manufacturing according to results of some limited researches. This paper presents a detailed review about some essential properties of waste and recycled plastics, important for WPCs production, and of research published on the effect of recycled plastics on the physical and mechanical properties of WPCs. PMID:23777666

  15. Plastic Surgery and Suicide: A Clinical Guide for Plastic Surgeons

    PubMed Central

    Coffey, M. Justin

    2016-01-01

    Summary: Several studies have identified an increased risk of suicide among patient populations which a plastic surgeon may have a high risk of encountering: women undergoing breast augmentation, cosmetic surgery patients, and breast cancer patients. No formal guidelines exist to assist a plastic surgeon when faced with such a patient, and not every plastic surgery team has mental health clinicians that are readily accessible for consultation or referral. The goal of this clinical guide is to offer plastic surgeons a set of practical approaches to manage potentially suicidal patients. In addition, the authors review a screening tool, which can assist surgeons when encountering high-risk patients.

  16. Direct liquefaction of plastics and coprocessing of coal with plastics

    SciTech Connect

    Huffman, G.P.; Feng, Z.; Mahajan, V.

    1995-12-31

    The objectives of this work were to optimize reaction conditions for the direct liquefaction of waste plastics and the coprocessing of coal with waste plastics. In previous work, the direct liquefaction of medium and high density polyethylene (PE), polypropylene (PPE), poly(ethylene terephthalate) (PET), and a mixed plastic waste, and the coliquefaction of these plastics with coals of three different ranks was studied. The results established that a solid acid catalyst (HZSM-5 zeolite) was highly active for the liquefaction of the plastics alone, typically giving oil yields of 80-95% and total conversions of 90-100% at temperatures of 430-450 {degrees}C. In the coliquefaction experiments, 50:50 mixtures of plastic and coal were used with a tetralin solvent (tetralin:solid = 3:2). Using approximately 1% of the HZSM-5 catalyst and a nanoscale iron catalyst, oil yields of 50-70% and total conversion of 80-90% were typical. In the current year, further investigations were conducted of the liquefaction of PE, PPE, and a commingled waste plastic obtained from the American Plastics Council (APC), and the coprocessing of PE, PPE and the APC plastic with Black Thunder subbituminous coal. Several different catalysts were used in these studies.

  17. Plastic Surgery and Suicide: A Clinical Guide for Plastic Surgeons.

    PubMed

    Reddy, Vikram; Coffey, M Justin

    2016-08-01

    Several studies have identified an increased risk of suicide among patient populations which a plastic surgeon may have a high risk of encountering: women undergoing breast augmentation, cosmetic surgery patients, and breast cancer patients. No formal guidelines exist to assist a plastic surgeon when faced with such a patient, and not every plastic surgery team has mental health clinicians that are readily accessible for consultation or referral. The goal of this clinical guide is to offer plastic surgeons a set of practical approaches to manage potentially suicidal patients. In addition, the authors review a screening tool, which can assist surgeons when encountering high-risk patients. PMID:27622096

  18. Plastic Surgery and Suicide: A Clinical Guide for Plastic Surgeons

    PubMed Central

    Coffey, M. Justin

    2016-01-01

    Summary: Several studies have identified an increased risk of suicide among patient populations which a plastic surgeon may have a high risk of encountering: women undergoing breast augmentation, cosmetic surgery patients, and breast cancer patients. No formal guidelines exist to assist a plastic surgeon when faced with such a patient, and not every plastic surgery team has mental health clinicians that are readily accessible for consultation or referral. The goal of this clinical guide is to offer plastic surgeons a set of practical approaches to manage potentially suicidal patients. In addition, the authors review a screening tool, which can assist surgeons when encountering high-risk patients. PMID:27622096

  19. Abort Trigger False Positive and False Negative Analysis Methodology for Threshold-Based Abort Detection

    NASA Technical Reports Server (NTRS)

    Melcher, Kevin J.; Cruz, Jose A.; Johnson Stephen B.; Lo, Yunnhon

    2015-01-01

    This paper describes a quantitative methodology for bounding the false positive (FP) and false negative (FN) probabilities associated with a human-rated launch vehicle abort trigger (AT) that includes sensor data qualification (SDQ). In this context, an AT is a hardware and software mechanism designed to detect the existence of a specific abort condition. Also, SDQ is an algorithmic approach used to identify sensor data suspected of being corrupt so that suspect data does not adversely affect an AT's detection capability. The FP and FN methodologies presented here were developed to support estimation of the probabilities of loss of crew and loss of mission for the Space Launch System (SLS) which is being developed by the National Aeronautics and Space Administration (NASA). The paper provides a brief overview of system health management as being an extension of control theory; and describes how ATs and the calculation of FP and FN probabilities relate to this theory. The discussion leads to a detailed presentation of the FP and FN methodology and an example showing how the FP and FN calculations are performed. This detailed presentation includes a methodology for calculating the change in FP and FN probabilities that result from including SDQ in the AT architecture. To avoid proprietary and sensitive data issues, the example incorporates a mixture of open literature and fictitious reliability data. Results presented in the paper demonstrate the effectiveness of the approach in providing quantitative estimates that bound the probability of a FP or FN abort determination.

  20. Processing plastics in Packerland

    SciTech Connect

    Ridgley, H.

    1998-04-01

    Located in Green Bay, Wisconsin, Catenation, Inc. is a privately held recycling company dedicated to the recovery of post-consumer plastic containers. What makes the company stand out is its ability to separate and sort material from a commingled bale. Catenation uses custom-made, high-speed, computer-driven vision equipment to scan and sort every bottle by category. The computer even can be programmed to distinguish soiled jugs from clean containers. This is a selling point for buyers of resin who are insistent on receiving high-grade material.

  1. Fabrication of plastic biochips

    SciTech Connect

    Saaem, Ishtiaq; Ma, Kuo-Sheng; Alam, S. Munir; Tian Jingdong

    2010-07-15

    A versatile surface functionalization procedure based on rf magnetron sputtering of silica was performed on poly(methylmethacrylate), polycarbonate, polypropylene, and cyclic olefin copolymers (Topas 6015). The hybrid thermoplastic surfaces were characterized by x-ray photoelectron spectrometer analysis and contact angle measurements. The authors then used these hybrid materials to perform a sandwich assay targeting an HIV-1 antibody using fluorescent detection and biotinylated peptides immobilized using the bioaffinity of biotin-neutravidin. They found a limit of detection similar to arrays on glass surfaces and believed that this plastic biochip platform may be used for the development of disposable immunosensing and diagnostic applications.

  2. History of reinforced plastics

    SciTech Connect

    Milewski, J.V.; Rosato, D.V.

    1981-01-01

    This history of reinforced plastics is told by combining the individual histories of each reinforcement and the way in which they added to and changed the direction and rate of growth of the industry. The early history is based on all resins, fillers, and fibers found in nature. Then came the Baekeland revolution with the first synthetic resin which lasted about 25 years, at which time synthetic fiber glass and polyester resin dramatically changed the industry. Now, for the 1980s, the high modulus fibers developed 10 to 20 years ago are reshaping the industry. 32 figures.

  3. Psychotherapy and brain plasticity

    PubMed Central

    Collerton, Daniel

    2013-01-01

    In this paper, I will review why psychotherapy is relevant to the question of how consciousness relates to brain plasticity. A great deal of the research and theorizing on consciousness and the brain, including my own on hallucinations for example (Collerton and Perry, 2011) has focused upon specific changes in conscious content which can be related to temporal changes in restricted brain systems. I will argue that psychotherapy, in contrast, allows only a focus on holistic aspects of consciousness; an emphasis which may usefully complement what can be learnt from more specific methodologies. PMID:24046752

  4. Advances in engineering plastics

    SciTech Connect

    Leonard, L.

    1997-12-01

    New polymers are being commercialized in record numbers, offering the product designer a new realm of possibilities, and promising tough competition to the traditional engineering resins. Most of the growth is in single-site catalyzed resins. Metallocene (and non-metallocene) single-site catalysts enhance polymer architecture to generate highly uniform molecules, and even permit tailoring new categories of polymers. These new materials include the truly unique aliphatic polyketone, syndiotactic polystyrene (SPS); polyethylene naphthalate (PEN) resins; and novel variations of established polymers. This article provides a closer look at these newcomers to the plastics marketplace, with an emphasis on their properties and potential applications.

  5. 38 CFR 21.9740 - False, late, or missing reports.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false False, late, or missing..., late, or missing reports. (a) Eligible individual. Payments may not be based on false or misleading....S.C. chapter 33 in the same manner as they are applied to people who make similar false...

  6. 38 CFR 21.7658 - False, late, or missing reports.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false False, late, or missing... Reserve Pursuit of Course and Required Reports § 21.7658 False, late, or missing reports. (a) Reservist... the same manner as they are applied to people who make similar false or misleading claims for...

  7. 38 CFR 21.7158 - False, late, or missing reports.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false False, late, or missing... (Montgomery GI Bill-Active Duty) Pursuit of Courses § 21.7158 False, late, or missing reports. (a) Veteran....C. chapter 30 in the same manner as they are applied to people who make similar false or...

  8. 19 CFR 148.19 - False or fraudulent statement.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false False or fraudulent statement. 148.19 Section 148... THE TREASURY (CONTINUED) PERSONAL DECLARATIONS AND EXEMPTIONS Declarations § 148.19 False or fraudulent statement. A passenger who makes any false or fraudulent statement or engages in other...

  9. 7 CFR 160.90 - False, misleading, or deceitful practices.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false False, misleading, or deceitful practices. 160.90... REGULATIONS AND STANDARDS FOR NAVAL STORES Labeling, Advertising and Packing § 160.90 False, misleading, or... commerce or of anything offered as such shall be false, misleading, or deceitful in any manner....

  10. Adults' Memories of Childhood: True and False Reports

    ERIC Educational Resources Information Center

    Qin, Jianjian; Ogle, Christin M.; Goodman, Gail S.

    2008-01-01

    In 3 experiments, the authors examined factors that, according to the source-monitoring framework, might influence false memory formation and true/false memory discernment. In Experiment 1, combined effects of warning and visualization on false childhood memory formation were examined, as were individual differences in true and false childhood…

  11. 42 CFR 21.23 - False statements as disqualification.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 42 Public Health 1 2013-10-01 2013-10-01 false False statements as disqualification. 21.23 Section... COMMISSIONED OFFICERS Appointment § 21.23 False statements as disqualification. Willfully false statements shall be cause for rejection of the application or, as provided in subpart N of this part, for dismissal....

  12. 42 CFR 21.23 - False statements as disqualification.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 42 Public Health 1 2014-10-01 2014-10-01 false False statements as disqualification. 21.23 Section... COMMISSIONED OFFICERS Appointment § 21.23 False statements as disqualification. Willfully false statements shall be cause for rejection of the application or, as provided in subpart N of this part, for dismissal....

  13. 42 CFR 21.23 - False statements as disqualification.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 42 Public Health 1 2011-10-01 2011-10-01 false False statements as disqualification. 21.23 Section 21.23 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES PERSONNEL COMMISSIONED OFFICERS Appointment § 21.23 False statements as disqualification. Willfully false...

  14. 42 CFR 21.23 - False statements as disqualification.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false False statements as disqualification. 21.23 Section 21.23 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES PERSONNEL COMMISSIONED OFFICERS Appointment § 21.23 False statements as disqualification. Willfully false...

  15. 38 CFR 21.7658 - False, late, or missing reports.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2013-07-01 2013-07-01 false False, late, or missing... Reserve Pursuit of Course and Required Reports § 21.7658 False, late, or missing reports. (a) Reservist... provisions of §§ 21.4006 and 21.4007 of this part to a reservist or any other person who submits false...

  16. 38 CFR 21.7658 - False, late, or missing reports.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2012-07-01 2012-07-01 false False, late, or missing... Reserve Pursuit of Course and Required Reports § 21.7658 False, late, or missing reports. (a) Reservist... provisions of §§ 21.4006 and 21.4007 of this part to a reservist or any other person who submits false...

  17. 38 CFR 21.7658 - False, late, or missing reports.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2011-07-01 2011-07-01 false False, late, or missing... Reserve Pursuit of Course and Required Reports § 21.7658 False, late, or missing reports. (a) Reservist... provisions of §§ 21.4006 and 21.4007 of this part to a reservist or any other person who submits false...

  18. 38 CFR 21.7658 - False, late, or missing reports.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2014-07-01 2014-07-01 false False, late, or missing... Reserve Pursuit of Course and Required Reports § 21.7658 False, late, or missing reports. (a) Reservist... provisions of §§ 21.4006 and 21.4007 of this part to a reservist or any other person who submits false...

  19. Presynaptic long-term plasticity

    PubMed Central

    Yang, Ying; Calakos, Nicole

    2013-01-01

    Long-term synaptic plasticity is a major cellular substrate for learning, memory, and behavioral adaptation. Although early examples of long-term synaptic plasticity described a mechanism by which postsynaptic signal transduction was potentiated, it is now apparent that there is a vast array of mechanisms for long-term synaptic plasticity that involve modifications to either or both the presynaptic terminal and postsynaptic site. In this article, we discuss current and evolving approaches to identify presynaptic mechanisms as well as discuss their limitations. We next provide examples of the diverse circuits in which presynaptic forms of long-term synaptic plasticity have been described and discuss the potential contribution this form of plasticity might add to circuit function. Finally, we examine the present evidence for the molecular pathways and cellular events underlying presynaptic long-term synaptic plasticity. PMID:24146648

  20. Polyolefins as additives in plastics

    SciTech Connect

    Deanin, R.D.

    1993-12-31

    Polyolefins are not only major commodity plastics - they are also very useful as additives, both in other polyolefins and also in other types of plastics. This review covers ethylene, propylene, butylene and isobutylene polymers, in blends with each other, and as additives to natural rubber, styrene/butadiene rubber, polystyrene, polyvinyl chloride, polymethyl methacrylate, polyphenylene oxide, polycarbonate, thermoplastic polyesters, polyurethanes, polyamides, and mixed automotive plastics recycling.

  1. The commercialization of plastic surgery.

    PubMed

    Swanson, Eric

    2013-09-01

    The last decade has brought a major challenge to the traditional practice of plastic surgery from corporations that treat plastic surgery as a commercial product and market directly to the public. This corporate medicine model may include promotion of a trademarked procedure or device, national advertising that promises stunning results, sales consultants, and claims of innovation, superiority, and improved safety. This article explores the ethics of this business practice and whether corporate medicine is a desirable model for patients and plastic surgeons.

  2. Optogenetics and synaptic plasticity.

    PubMed

    Xie, Yu-feng; Jackson, Michael F; Macdonald, John F

    2013-11-01

    The intricate and complex interaction between different populations of neurons in the brain has imposed limits on our ability to gain detailed understanding of synaptic transmission and its integration when employing classical electrophysiological approaches. Indeed, electrical field stimulation delivered via traditional microelectrodes does not permit the targeted, precise and selective control of neuronal activity amongst a varied population of neurons and their inputs (eg, cholinergic, dopaminergic or glutamatergic neurons). Recently established optogenetic techniques overcome these limitations allowing precise control of the target neuron populations, which is essential for the elucidation of the neural substrates underlying complex animal behaviors. Indeed, by introducing light-activated channels (ie, microbial opsin genes) into specific neuronal populations, optogenetics enables non-invasive optical control of specific neurons with milliseconds precision. These approaches can readily be applied to freely behaving live animals. Recently there is increased interests in utilizing optogenetics tools to understand synaptic plasticity and learning/memory. Here, we summarize recent progress in applying optogenetics in in the study of synaptic plasticity.

  3. Americium behaviour in plastic vessels.

    PubMed

    Legarda, F; Herranz, M; Idoeta, R; Abelairas, A

    2010-01-01

    The adsorption of (241)Am dissolved in water in different plastic storage vessels was determined. Three different plastics were investigated with natural and distilled waters and the retention of (241)Am by these plastics was studied. The same was done by varying vessel agitation time, vessel agitation speed, surface/volume ratio of water in the vessels and water pH. Adsorptions were measured to be between 0% and 70%. The adsorption of (241)Am is minimized with no water agitation, with PET or PVC plastics, and by water acidification. PMID:20042341

  4. Americium behaviour in plastic vessels.

    PubMed

    Legarda, F; Herranz, M; Idoeta, R; Abelairas, A

    2010-01-01

    The adsorption of (241)Am dissolved in water in different plastic storage vessels was determined. Three different plastics were investigated with natural and distilled waters and the retention of (241)Am by these plastics was studied. The same was done by varying vessel agitation time, vessel agitation speed, surface/volume ratio of water in the vessels and water pH. Adsorptions were measured to be between 0% and 70%. The adsorption of (241)Am is minimized with no water agitation, with PET or PVC plastics, and by water acidification.

  5. 49 CFR 40.105 - What happens if the laboratory reports a result different from that expected for a blind specimen?

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... the reason for the discrepancy. (c) If the unexpected result is a false positive, adulterated, or... 49 Transportation 1 2012-10-01 2012-10-01 false What happens if the laboratory reports a result... discrepancy. (b) If the unexpected result is a false negative, you must provide the laboratory with...

  6. "False Positive" Claims of Near-Death Experiences and "False Negative" Denials of Near-Death Experiences

    ERIC Educational Resources Information Center

    Greyson, Bruce

    2005-01-01

    Some persons who claim to have had near-death experiences (NDEs) fail research criteria for having had NDEs ("false positives"); others who deny having had NDEs do meet research criteria for having had NDEs ("false negatives"). The author evaluated false positive claims and false negative denials in an organization that promotes near-death…

  7. Plastics recycling: challenges and opportunities

    PubMed Central

    Hopewell, Jefferson; Dvorak, Robert; Kosior, Edward

    2009-01-01

    Plastics are inexpensive, lightweight and durable materials, which can readily be moulded into a variety of products that find use in a wide range of applications. As a consequence, the production of plastics has increased markedly over the last 60 years. However, current levels of their usage and disposal generate several environmental problems. Around 4 per cent of world oil and gas production, a non-renewable resource, is used as feedstock for plastics and a further 3–4% is expended to provide energy for their manufacture. A major portion of plastic produced each year is used to make disposable items of packaging or other short-lived products that are discarded within a year of manufacture. These two observations alone indicate that our current use of plastics is not sustainable. In addition, because of the durability of the polymers involved, substantial quantities of discarded end-of-life plastics are accumulating as debris in landfills and in natural habitats worldwide. Recycling is one of the most important actions currently available to reduce these impacts and represents one of the most dynamic areas in the plastics industry today. Recycling provides opportunities to reduce oil usage, carbon dioxide emissions and the quantities of waste requiring disposal. Here, we briefly set recycling into context against other waste-reduction strategies, namely reduction in material use through downgauging or product reuse, the use of alternative biodegradable materials and energy recovery as fuel. While plastics have been recycled since the 1970s, the quantities that are recycled vary geographically, according to plastic type and application. Recycling of packaging materials has seen rapid expansion over the last decades in a number of countries. Advances in technologies and systems for the collection, sorting and reprocessing of recyclable plastics are creating new opportunities for recycling, and with the combined actions of the public, industry and governments it

  8. Plastics recycling: challenges and opportunities.

    PubMed

    Hopewell, Jefferson; Dvorak, Robert; Kosior, Edward

    2009-07-27

    Plastics are inexpensive, lightweight and durable materials, which can readily be moulded into a variety of products that find use in a wide range of applications. As a consequence, the production of plastics has increased markedly over the last 60 years. However, current levels of their usage and disposal generate several environmental problems. Around 4 per cent of world oil and gas production, a non-renewable resource, is used as feedstock for plastics and a further 3-4% is expended to provide energy for their manufacture. A major portion of plastic produced each year is used to make disposable items of packaging or other short-lived products that are discarded within a year of manufacture. These two observations alone indicate that our current use of plastics is not sustainable. In addition, because of the durability of the polymers involved, substantial quantities of discarded end-of-life plastics are accumulating as debris in landfills and in natural habitats worldwide. Recycling is one of the most important actions currently available to reduce these impacts and represents one of the most dynamic areas in the plastics industry today. Recycling provides opportunities to reduce oil usage, carbon dioxide emissions and the quantities of waste requiring disposal. Here, we briefly set recycling into context against other waste-reduction strategies, namely reduction in material use through downgauging or product reuse, the use of alternative biodegradable materials and energy recovery as fuel. While plastics have been recycled since the 1970s, the quantities that are recycled vary geographically, according to plastic type and application. Recycling of packaging materials has seen rapid expansion over the last decades in a number of countries. Advances in technologies and systems for the collection, sorting and reprocessing of recyclable plastics are creating new opportunities for recycling, and with the combined actions of the public, industry and governments it

  9. Plastics recycling: challenges and opportunities.

    PubMed

    Hopewell, Jefferson; Dvorak, Robert; Kosior, Edward

    2009-07-27

    Plastics are inexpensive, lightweight and durable materials, which can readily be moulded into a variety of products that find use in a wide range of applications. As a consequence, the production of plastics has increased markedly over the last 60 years. However, current levels of their usage and disposal generate several environmental problems. Around 4 per cent of world oil and gas production, a non-renewable resource, is used as feedstock for plastics and a further 3-4% is expended to provide energy for their manufacture. A major portion of plastic produced each year is used to make disposable items of packaging or other short-lived products that are discarded within a year of manufacture. These two observations alone indicate that our current use of plastics is not sustainable. In addition, because of the durability of the polymers involved, substantial quantities of discarded end-of-life plastics are accumulating as debris in landfills and in natural habitats worldwide. Recycling is one of the most important actions currently available to reduce these impacts and represents one of the most dynamic areas in the plastics industry today. Recycling provides opportunities to reduce oil usage, carbon dioxide emissions and the quantities of waste requiring disposal. Here, we briefly set recycling into context against other waste-reduction strategies, namely reduction in material use through downgauging or product reuse, the use of alternative biodegradable materials and energy recovery as fuel. While plastics have been recycled since the 1970s, the quantities that are recycled vary geographically, according to plastic type and application. Recycling of packaging materials has seen rapid expansion over the last decades in a number of countries. Advances in technologies and systems for the collection, sorting and reprocessing of recyclable plastics are creating new opportunities for recycling, and with the combined actions of the public, industry and governments it

  10. Decoy Methods for Assessing False Positives and False Discovery Rates in Shotgun Proteomics

    PubMed Central

    Wang, Guanghui; Wu, Wells W.; Zhang, Zheng; Masilamani, Shyama; Shen, Rong-Fong

    2008-01-01

    The potential of getting a significant number of false positives (FPs) in peptide-spectrum matches (PSMs) obtained by proteomic database search has been well-recognized. Among the attempts to assess FPs, the concomitant use of target and decoy databases is widely practiced. By adjusting filtering criteria, FPs and false discovery rate (FDR) can be controlled at a desired level. Although the target-decoy approach is gaining in popularity, subtle differences in decoy construction (e.g., reversing vs. stochastic methods), rate calculation (e.g., total vs. unique PSMs), or searching (separate vs. composite) do exist among various implementations. In the present study, we evaluated the effects of these differences on FP and FDR estimations using a rat kidney protein sample and the SEQUEST search engine as an example. On the effects of decoy construction, we found that, when a single scoring filter (XCorr) was used, stochastic methods generated a higher estimation of FPs and FDR than sequence reversing methods, likely due to an increase in unique peptides. This higher estimation could largely be attenuated by creating decoy databases similar in effective size, but not by a simple normalization with a unique-peptide coefficient. When multiple filters were applied, the differences seen between reversing and stochastic methods significantly diminished, suggesting multiple filterings reduce the dependency on how a decoy is constructed. For a fixed set of filtering criteria, FDR and FPs estimated by using unique PSMs were almost twice those using total PSMs. The higher estimation seemed to be dependent on data acquisition setup. As to the differences between performing separate or composite searches, in general, FDR estimated from separate search was about three times that from composite search. The degree of difference gradually decreased as the filtering criteria became more stringent. Paradoxically, the estimated true positives in separate search were higher when multiple

  11. Decoy methods for assessing false positives and false discovery rates in shotgun proteomics.

    PubMed

    Wang, Guanghui; Wu, Wells W; Zhang, Zheng; Masilamani, Shyama; Shen, Rong-Fong

    2009-01-01

    The potential of getting a significant number of false positives (FPs) in peptide-spectrum matches (PSMs) obtained by proteomic database search has been well-recognized. Among the attempts to assess FPs, the concomitant use of target and decoy databases is widely practiced. By adjusting filtering criteria, FPs and false discovery rate (FDR) can be controlled at a desired level. Although the target-decoy approach is gaining in popularity, subtle differences in decoy construction (e.g., reversing vs stochastic methods), rate calculation (e.g., total vs unique PSMs), or searching (separate vs composite) do exist among various implementations. In the present study, we evaluated the effects of these differences on FP and FDR estimations using a rat kidney protein sample and the SEQUEST search engine as an example. On the effects of decoy construction, we found that, when a single scoring filter (XCorr) was used, stochastic methods generated a higher estimation of FPs and FDR than sequence reversing methods, likely due to an increase in unique peptides. This higher estimation could largely be attenuated by creating decoy databases similar in effective size but not by a simple normalization with a unique-peptide coefficient. When multiple filters were applied, the differences seen between reversing and stochastic methods significantly diminished, suggesting multiple filterings reduce the dependency on how a decoy is constructed. For a fixed set of filtering criteria, FDR and FPs estimated by using unique PSMs were almost twice those using total PSMs. The higher estimation seemed to be dependent on data acquisition setup. As to the differences between performing separate or composite searches, in general, FDR estimated from the separate search was about three times that from the composite search. The degree of difference gradually decreased as the filtering criteria became more stringent. Paradoxically, the estimated true positives in separate search were higher when

  12. Telling true from false: cannabis users show increased susceptibility to false memories

    PubMed Central

    Riba, J; Valle, M; Sampedro, F; Rodríguez-Pujadas, A; Martínez-Horta, S; Kulisevsky, J; Rodríguez-Fornells, A

    2015-01-01

    Previous studies on the neurocognitive impact of cannabis use have found working and declarative memory deficits that tend to normalize with abstinence. An unexplored aspect of cognitive function in chronic cannabis users is the ability to distinguish between veridical and illusory memories, a crucial aspect of reality monitoring that relies on adequate memory function and cognitive control. Using functional magnetic resonance imaging, we show that abstinent cannabis users have an increased susceptibility to false memories, failing to identify lure stimuli as events that never occurred. In addition to impaired performance, cannabis users display reduced activation in areas associated with memory processing within the lateral and medial temporal lobe (MTL), and in parietal and frontal brain regions involved in attention and performance monitoring. Furthermore, cannabis consumption was inversely correlated with MTL activity, suggesting that the drug is especially detrimental to the episodic aspects of memory. These findings indicate that cannabis users have an increased susceptibility to memory distortions even when abstinent and drug-free, suggesting a long-lasting compromise of memory and cognitive control mechanisms involved in reality monitoring. PMID:25824306

  13. False alarms: How early warning signals falsely predict abrupt sea ice loss

    NASA Astrophysics Data System (ADS)

    Wagner, Till J. W.; Eisenman, Ian

    2016-04-01

    Uncovering universal early warning signals for critical transitions has become a coveted goal in diverse scientific disciplines, ranging from climate science to financial mathematics. There has been a flurry of recent research proposing such signals, with increasing autocorrelation and increasing variance being among the most widely discussed candidates. A number of studies have suggested that increasing autocorrelation alone may suffice to signal an impending transition, although some others have questioned this. Here we consider variance and autocorrelation in the context of sea ice loss in an idealized model of the global climate system. The model features no bifurcation, nor increased rate of retreat, as the ice disappears. Nonetheless, the autocorrelation of summer sea ice area is found to increase in a global warming scenario. The variance, by contrast, decreases. A simple physical mechanism is proposed to explain the occurrence of increasing autocorrelation but not variance when there is no approaching bifurcation. Additionally, a similar mechanism is shown to allow an increase in both indicators with no physically attainable bifurcation. This implies that relying on autocorrelation and variance as early warning signals can raise false alarms in the climate system, warning of "tipping points" that are not actually there.

  14. False alarms: How early warning signals falsely predict abrupt sea ice loss

    NASA Astrophysics Data System (ADS)

    Wagner, Till J. W.; Eisenman, Ian

    2015-12-01

    Uncovering universal early warning signals for critical transitions has become a coveted goal in diverse scientific disciplines, ranging from climate science to financial mathematics. There has been a flurry of recent research proposing such signals, with increasing autocorrelation and increasing variance being among the most widely discussed candidates. A number of studies have suggested that increasing autocorrelation alone may suffice to signal an impending transition, although some others have questioned this. Here we consider variance and autocorrelation in the context of sea ice loss in an idealized model of the global climate system. The model features no bifurcation, nor increased rate of retreat, as the ice disappears. Nonetheless, the autocorrelation of summer sea ice area is found to increase in a global warming scenario. The variance, by contrast, decreases. A simple physical mechanism is proposed to explain the occurrence of increasing autocorrelation but not variance when there is no approaching bifurcation. Additionally, a similar mechanism is shown to allow an increase in both indicators with no physically attainable bifurcation. This implies that relying on autocorrelation and variance as early warning signals can raise false alarms in the climate system, warning of "tipping points" that are not actually there.

  15. Recycle your plastic waste

    SciTech Connect

    Kuhlke, W.C. )

    1990-05-01

    This paper discusses how source reduction and recycling are alternatives to managing waste. This includes the recycling of material before it leaves the manufacturer or reducing the size of the product being made. In-plant reprocessing of plastic materials is one method of source reduction. Included are such applications as where an injection molder collects the spur, regrinds it, and feeds it back to make an injection molded part. When a polystyrene sheet is thermoformed to make cups, after cutting, the remaining sheet is recycled, chopped up and reextruded to make a sheet to again be fed to the thermoformer. The alternative would be to sell the waste or send it to the city dump.

  16. Plastics to fuel: A review

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This paper reviews recent developments in catalytic and non-catalytic degradation of waste plastics into fuels. Thermal degradation decomposes plastic into three fractions: gas, crude oil, and solid residue. Crude oil from non-catalytic pyrolysis is usually composed of higher boiling point hydrocarb...

  17. Plastics & Composites Technology Needs Assessment.

    ERIC Educational Resources Information Center

    Oakland Community Coll., Farmington, MI. Office of Institutional Planning and Analysis.

    In 1991, a study was conducted by Oakland Community College (OCC) to evaluate the need for a proposed plastics and composites technology program for design engineers. General information was obtained through a literature search, from the Society of the Plastics Industry, Inc., the Michigan Employment Security Commission, and interviews with…

  18. Computational strain gradient crystal plasticity

    NASA Astrophysics Data System (ADS)

    Niordson, Christian F.; Kysar, Jeffrey W.

    2014-01-01

    A numerical method for viscous strain gradient crystal plasticity theory is presented, which incorporates both energetic and dissipative gradient effects. The underlying minimum principles are discussed as well as convergence properties of the proposed finite element procedure. Three problems of plane crystal plasticity are studied: pure shear of a single crystal between rigid platens as well as plastic deformation around cylindrical voids in hexagonal close packed and face centered cubic crystals. Effective in-plane constitutive slip parameters for plane strain deformation of specifically oriented face centered cubic crystals are developed in terms of the crystallographic slip parameters. The effect on geometrically necessary dislocation structures introduced by plastic deformation is investigated as a function of the ratio of void radius to plasticity length scale.

  19. Biodegradability of degradable plastic waste.

    PubMed

    Agamuthu, P; Faizura, Putri Nadzrul

    2005-04-01

    Plastic waste constitutes the third largest waste volume in Malaysian municipal solid waste (MSW), next to putrescible waste and paper. The plastic component in MSW from Kuala Lumpur averages 24% (by weight), whereas the national mean is about 15%. The 144 waste dumps in the country receive about 95% of the MSW, including plastic waste. The useful life of the landfills is fast diminishing as the plastic waste stays un-degraded for more than 50 years. In this study the compostability of polyethylene and pro-oxidant additive-based environmentally degradable plastics (EDP) was investigated. Linear low-density polyethylene (LLDPE) samples exposed hydrolytically or oxidatively at 60 degrees C showed that the abiotic degradation path was oxidative rather than hydrolytic. There was a weight loss of 8% and the plastic has been oxidized as shown by the additional carbonyl group exhibited in the Fourier transform infra red (FTIR) Spectrum. Oxidation rate seemed to be influenced by the amount of pro-oxidant additive, the chemical structure and morphology of the plastic samples, and the surface area. Composting studies during a 45-day experiment showed that the percentage elongation (reduction) was 20% for McD samples [high-density polyethylene, (HDPE) with 3% additive] and LL samples (LLDPE with 7% additive) and 18% reduction for totally degradable plastic (TDP) samples (HDPE with 3% additive). Lastly, microbial experiments using Pseudomonas aeroginosa on carbon-free media with degradable plastic samples as the sole carbon source, showed confirmatory results. A positive bacterial growth and a weight loss of 2.2% for degraded polyethylene samples were evident to show that the degradable plastic is biodegradable.

  20. Chinese Preschoolers' Implicit and Explicit False-Belief Understanding

    ERIC Educational Resources Information Center

    Wang, Bo; Low, Jason; Jing, Zhang; Qinghua, Qu

    2012-01-01

    Mandarin-speaking preschoolers in Mainland China (3- to 4-year-olds; N = 192) were tested for dissociations between anticipatory looking (AL) and verbal judgments on false-belief tasks. The dissociation between the two kinds of understanding was robust despite direct false-belief test questions using a Mandarin specific think-falsely verb and…