Science.gov

Sample records for 2017a aluminium alloy

  1. Microstructure of friction stir welded joints of 2017A aluminium alloy sheets.

    PubMed

    Mroczka, K; Dutkiewicz, J; Pietras, A

    2010-03-01

    The present study examines a friction stir welded 2017A aluminium alloy. Transmission electron microscope investigations of the weld nugget revealed the average grain size of 5 microm, moderate density of dislocations as well as the presence of nanometric precipitates located mostly in grains interiors. Scanning electron microscope observations of fractures showed the presence of ductile fracture in the region of the weld nugget with brittle precipitates in the lower part. The microhardness analysis performed on the cross-section of the joints showed fairly small changes; however, after the artificial ageing process an increase in hardness was observed. The change of the joint hardness subject to the ageing process indicates partial supersaturation in the material during friction stir welding and higher precipitation hardening of the joint.

  2. Extrusion of aluminium alloys

    SciTech Connect

    Sheppard, T.

    1999-01-01

    In recent years the importance of extruded alloys has increased due to the decline in copper extrusion, increased use in structural applications, environmental impact and reduced energy consumption. There have also been huge technical advances. This text provides comprehensive coverage of the metallurgical, mathematical and practical features of the process. The contents include: continuum principles; metallurgical features affecting the extrusion of Al-alloys; extrusion processing; homogenization and extrusion conditions for specific alloys; processing of 6XXX alloys; plant utilization; Appendix A: specification of AA alloys and DIN equivalents; Appendix B: chemical compositions; and Appendix C: typical properties.

  3. Investigation of the formability of aluminium alloys at elevated temperatures

    NASA Astrophysics Data System (ADS)

    Tisza, M.; Budai, D.; Kovács, P. Z.; Lukács, Zs

    2016-11-01

    Aluminium alloys are more and more widely applied in car body manufacturing. Increasing the formability of aluminium alloys are one of the most relevant tasks in todays’ research topics. In this paper, the focus will be on the investigation of the formability of aluminium alloys concerning those material grades that are more widely applied in the automotive industry including the 5xxx and 6xxx aluminium alloy series. Recently, besides the cold forming of aluminium sheets the forming of aluminium alloys at elevated temperatures became a hot research topic, too. In our experimental investigations, we mostly examined the EN AW 5754 and EN AW 6082 aluminium alloys at elevated temperatures. We analysed the effect of various material and process parameters (e.g. temperature, sheet thickness) on the formability of aluminium alloys with particular emphasis on the Forming Limit Diagrams at elevated temperatures in order to find the optimum forming conditions for these alloys.

  4. Precipitate strengthening of nanostructured aluminium alloy.

    PubMed

    Wawer, Kinga; Lewandowska, Malgorzata; Kurzydlowski, Krzysztof J

    2012-11-01

    Grain boundaries and precipitates are the major microstructural features influencing the mechanical properties of metals and alloys. Refinement of the grain size to the nanometre scale brings about a significant increase in the mechanical strength of the materials because of the increased number of grain boundaries which act as obstacles to sliding dislocations. A similar effect is obtained if nanoscale precipitates are uniformly distributed in coarse grained matrix. The development of nanograin sized alloys raises the important question of whether or not these two mechanisms are "additive" and precipitate strengthening is effective in nanostructured materials. In the reported work, hydrostatic extrusion (HE) was used to obtain nanostructured 7475 aluminium alloy. Nanosized precipitates were obtained by post-HE annealing. It was found that such annealing at the low temperatures (100 degrees C) results in a significant increase in the microhardness (HV0.2) and strength of the nanostructured 7475 aluminium alloy. These results are discussed in terms of the interplay between the precipitation and deformation of nanocrystalline metals.

  5. Characteristics of Dissimilar FSW Welds of Aluminum Alloys 2017A and 7075 on the Basis of Multiple Layer Research

    NASA Astrophysics Data System (ADS)

    Mroczka, Krzysztof; Wójcicka, Anna; Pietras, Adam

    2013-09-01

    This work is concerned with the structure of the FSW joint of 2017A/7075 aluminum alloys, which was analyzed on the basis of a number of longitudinal and cross-sectional sections. Various ways and degrees of alloy stirring were identified, depending on the distance from the face of the weld. Furthermore, considerable variation in the length of the weld microstructures was demonstrated, reflecting the variability of the welding process. Studies of mechanical properties are also presented—the distributions of hardness on individual layers. A significant effect of plastic deformation on the hardness of the alloy 7075, which strengthened in deformed areas and shows weakness in the heat-affected zone, was noticed. The influence of the weld structure on the fracture of the sample, which was broken in the static tensile test, was analyzed applying scanning electron microscopy. The presence of non-deformed areas was revealed within the ductile fracture of the sample.

  6. Acoustic Emission from the Aluminium Alloy 7050.

    DTIC Science & Technology

    1979-10-01

    thick-section applications, has good stress - corrosion resistance, and is now being used in airframe construction. In this report, we present our AE...160.00 1S0.00 200.90 2SO.I9 TIMlE (sec) Fig. 8 Count-rate/time and nominal- stress /time curves for 7050 C-specimen (a) and 0-speimen lb). CO 0 CC 0T LLQ...A094 38" AERONAUTICAL RESEARCH LABS MELBOURNE (AUSTRALIA) F/6 11/6 ACOUSTIC EMISSION FROM THE ALUMINIUM ALLOY 7050 .(U) OCT 79 S M COUSLAND, C M SCALA

  7. Forming of aluminium alloy friction stir welds

    NASA Astrophysics Data System (ADS)

    Bruni, Carlo

    2016-10-01

    The present paper aims at investigating, through analytical models, numerical models and experiments, the effect of the warm deformation phase, realised with an in temperature upsetting, on the weld previously performed by friction stir lap welding on aluminium alloy blanks. The investigation allows to show the deformation zones after upsetting that determine the homogenisation of the weld section. The analytical model allows to relate the friction factor with the upsetting load. The presence on the weld of not elevated friction factor values determines the deformation and localisation levels very useful for the weld. Such methodology allows to improve the weld itself with the forming phase.

  8. Aluminium alloys in municipal solid waste incineration bottom ash.

    PubMed

    Hu, Yanjun; Rem, Peter

    2009-05-01

    With the increasing growth of incineration of household waste, more and more aluminium is retained in municipal solid waste incinerator bottom ash. Therefore recycling of aluminium from bottom ash becomes increasingly important. Previous research suggests that aluminium from different sources is found in different size fractions resulting in different recycling rates. The purpose of this study was to develop analytical and sampling techniques to measure the particle size distribution of individual alloys in bottom ash. In particular, cast aluminium alloys were investigated. Based on the particle size distribution it was computed how well these alloys were recovered in a typical state-of-the-art treatment plant. Assessment of the cast alloy distribution was carried out by wet physical separation processes, as well as chemical methods, X-ray fluorescence analysis and electron microprobe analysis. The results from laboratory analyses showed that cast alloys tend to concentrate in the coarser fractions and therefore are better recovered in bottom ash treatment plants.

  9. Examples of liquiq metal embrittlement in industrial aluminium alloys

    NASA Astrophysics Data System (ADS)

    Bréchet, Y.; Rodine, A.; Véron, M.; Péron, S.; Deschamps, A.

    2002-09-01

    Liquid metal embrittlement (LME) phenomena were investigated in two industrial aluminium alloys. Gallium penetration in 7010 alloys was systematically investigated to shed light on the effect of microstructure and plasticity ahead of the crack tip. Hot temperature shortness in 5083 alloy is given as an example of cleavage induced by LME.

  10. Computer modelling of age hardening for cast aluminium alloys

    NASA Astrophysics Data System (ADS)

    Wu, Linda; Ferguson, W. George

    2009-08-01

    Age hardening, or precipitation hardening, is one of the most widely adopted techniques for strengthening of aluminium alloys. Although various age hardening models have been developed for aluminium alloys, from the large volume of literature reviewed, it appears that the bulk of the research has been concentrated on wrought aluminium alloys, only a few of the established precipitation models have been applied to the casting aluminium alloys. In the present work, there are two modelling methods that have been developed and applied to the casting aluminium alloys A356 and A357. One is based on the Shercliff-Ashby methodology to produce a process model, by which we mean a mathematical relationship between process variables (alloy composition, ageing temperature and time) and material properties (yield strength or hardness) through microstructure evolution (precipitate radius, volume fraction). The other method is based on the Kampmann and Wagner Numerical (KWN) model which deals with concomitant nucleation, growth and coarsening and is thus capable of predicting the full evolution of the particle size distribution and then a strength model is used to evaluate the resulting change in hardness or yield strength at room temperature by taking into account contributions from lattice resistance, solid solution hardening and precipitation hardening.

  11. Ageing characteristics of aluminium alloy aluminosilicate discontinuous fiber reinforced composites

    SciTech Connect

    Nath, D.; Singh, V.

    1999-03-05

    Development of continuous fiber reinforced metal matrix composites is aimed at providing high specific strength and stiffness needed for aerospace and some critical high temperature structural applications. Considerable efforts have been made, during the last decade, to improve the strength of age-hardening aluminium alloy matrix composites by suitable heat treatment. It has also been well established that age-hardenable aluminium alloy composites show accelerated ageing behavior because of enhanced dislocation density at the fiber/matrix interface resulting from thermal expansion mismatch between ceramic fiber and the metal matrix. The accelerated ageing of aluminium alloy composites either from dislocation density or the residual stress, as a result of thermal expansion mismatch is dependent on the size of whisker and particulate. Investigations have also been made on the effect of volume fraction of particulate on the ageing behavior of aluminium alloys. The present investigation is concerned with characterization of age-hardening behavior of an Al-Si-Cu-Mg(AA 336) alloy alumino-silicate discontinuous fiber-reinforced composites (referred to as aluminium MMCs in the present text) being developed for automotive pistons. An effort is made to study the effect of volume fraction of the reinforcement on age-hardening behavior of this composite.

  12. Incremental forming of aluminium alloys in cryogenic environment

    NASA Astrophysics Data System (ADS)

    Vanhove, Hans; Mohammadi, Amirahmad; Duflou, Joost R.

    2016-10-01

    Incremental Sheet Forming processes suffer from stringent forming limits, restricting the range of producible geometries. Through in-process cooling of the sheet to cryogenic level, this paper explores the potential of altering material properties benefiting the formability and residual hardness of different aluminium alloys. Global cooling of aluminium sheets with liquid nitrogen and dry ice allows to reach temperatures of 78K and 193K respectively. Extended with experiments at room temperature (293K), these tests form a base for comparison of surface quality, formability and residual hardness. As an aluminium alloy commonly used for its high strength to weight ratio, but suffering from limited formability compared to draw-quality steels, AA5083-H111 is of interest for cryogenic treatment. AA1050-H24 is included in the test campaign as a base for commercially pure aluminium.

  13. Microstructural and Mechanical Characterization of Zr Modified 2014 Aluminium Alloy

    DTIC Science & Technology

    2007-11-02

    heated using an induction furnace; the temperature stabilisation time was 6 min. -The gauge section of samples was a solid cylinder with a length (L) of...torsion tests - Fatigue tests -Fracture observations Introduction -Aluminium sheets require a good attitude to the cold metal forming. -Al-Cu-Mg alloys...precipitation occurring during hot deformation or heat treatment Introduction -The precipitation sequence for 2014 Al alloys has been extensively

  14. The Corrosion Resistance and Paint Adhesion Properties of Chromate Conversion Coatings on Aluminium and Its Alloys

    DTIC Science & Technology

    1976-05-01

    aluminium and its alloys has been evaluated with respect to both corrosion resistance of, and paint adhesion to, the chromate films. The process involves...The findings in this Report will be used as the basis for a Defence Standard for chromate conversion coatings for aluminium and aluminium alloys...3 PROPRIETARY CHROMATE CONVERSION COATINGS FOR ALUMINIUM 17 4 PAINT ADHESION 19 5 DISCUSSION 21 6 CONCLUSIONS 24 Acknowledgments 25 Appendix A

  15. Recycling of aluminium scrap for secondary Al-Si alloys.

    PubMed

    Velasco, Eulogio; Nino, Jose

    2011-07-01

    An increasing amount of recycled aluminium is going into the production of aluminium alloy used for automotive applications. In these applications, it is necessary to control and remove alloy impurities and inclusions. Cleaning and fluxing processes are widely used during processing of the alloys for removal of inclusions, hydrogen and excess of magnesium. These processes use salt fluxes based in the system NaCl-KCl, injection of chlorine or mixture of chlorine with an inert gas. The new systems include a graphite wand and a circulation device to force convection in the melt and permit the bubbling and dispersion of reactive and cleaning agents. This paper discusses the recycling of aluminium alloys in rotary and reverberatory industrial furnaces. It focuses on the removal of magnesium during the melting process. In rotary furnaces, the magnesium lost is mainly due to the oxidation process at high temperatures. The magnesium removal is carried out by the reaction between chlorine and magnesium, with its efficiency associated to kinetic factors such as concentration of magnesium, mixing, and temperature. These factors are also related to emissions generated during the demagging process. Improvements in the metallic yield can be reached in rotary furnaces if the process starts with a proper salt, with limits of addition, and avoiding long holding times. To improve throughput in reverberatories, start the charging with high magnesium content material and inject chlorine gas if the molten metal is at the right temperature. Removal of magnesium through modern technologies can be efficiently performed to prevent environmental problems.

  16. Carbon treated commercial aluminium alloys as anodes for aluminium-air batteries in sodium chloride electrolyte

    NASA Astrophysics Data System (ADS)

    Pino, M.; Herranz, D.; Chacón, J.; Fatás, E.; Ocón, P.

    2016-09-01

    An easy treatment based in carbon layer deposition into aluminium alloys is presented to enhance the performance of Al-air primary batteries with neutral pH electrolyte. The jellification of aluminate in the anode surface is described and avoided by the carbon covering. Treated commercial Al alloys namely Al1085 and Al7475 are tested as anodes achieving specific capacities above 1.2 Ah g-1vs 0.5 Ah g-1 without carbon covering. The influence of the binder proportion in the treatment as well as different carbonaceous materials, Carbon Black, Graphene and Pyrolytic Graphite are evaluated as candidates for the covering. Current densities of 1-10 mA cm-2 are measured and the influence of the alloy explored. A final battery design of 4 cells in series is presented for discharges with a voltage plateau of 2 V and 1 Wh g-1 energy density.

  17. Mechanical Properties of Particulate Reinforced Aluminium Alloy Matrix Composite

    SciTech Connect

    Sayuti, M.; Sulaiman, S.; Baharudin, B. T. H. T.; Arifin, M. K. A.; Suraya, S.; Vijayaram, T. R.

    2011-01-17

    This paper discusses the mechanical properties of Titanium Carbide (TiC) particulate reinforced aluminium-silicon alloy matrix composite. TiC particulate reinforced LM6 alloy matrix composites were fabricated by carbon dioxide sand molding process with different particulate weight fraction. Tensile strength, hardness and microstructure studies were conducted to determine the maximum load, tensile strength, modulus of elasticity and fracture surface analysis have been performed to characterize the morphological aspects of the test samples after tensile testing. Hardness values are measured for the TiC reinforced LM6 alloy composites and it has been found that it gradually increases with increased addition of the reinforcement phase. The tensile strength of the composites increased with the increase percentage of TiC particulate.

  18. Nanostructural hierarchy increases the strength of aluminium alloys.

    PubMed

    Liddicoat, Peter V; Liao, Xiao-Zhou; Zhao, Yonghao; Zhu, Yuntian; Murashkin, Maxim Y; Lavernia, Enrique J; Valiev, Ruslan Z; Ringer, Simon P

    2010-09-07

    Increasing the strength of metallic alloys while maintaining formability is an interesting challenge for enabling new generations of lightweight structures and technologies. In this paper, we engineer aluminium alloys to contain a hierarchy of nanostructures and possess mechanical properties that expand known performance boundaries-an aerospace-grade 7075 alloy exhibits a yield strength and uniform elongation approaching 1 GPa and 5%, respectively. The nanostructural architecture was observed using novel high-resolution microscopy techniques and comprises a solid solution, free of precipitation, featuring (i) a high density of dislocations, (ii) subnanometre intragranular solute clusters, (iii) two geometries of nanometre-scale intergranular solute structures and (iv) grain sizes tens of nanometres in diameter. Our results demonstrate that this novel architecture offers a design pathway towards a new generation of super-strong materials with new regimes of property-performance space.

  19. Numerical Modelling of Drawbeads for Forming of Aluminium Alloys

    NASA Astrophysics Data System (ADS)

    Joshi, Y.; Christiansen, P.; Masters, I.; Bay, N.; Dashwood, R.

    2016-08-01

    The drawbeads in stamping tools are usually designed based on experience from the forming of steel. However, aluminium alloys display different forming behaviour to steels, which is not reflected in the drawbead design for tools used for stamping aluminium. This paper presents experimental results from different semi-circular drawbead geometries commonly encountered in automotive dies and compares them to those obtained from Stoughton's analytical drawbead model and the 2D plane strain drawbead model set up using LS-DYNA. The study was conducted on lubricated NG5754 strips. The results presented are in terms of drawbead restraining force versus strip displacement, as a function of drawbead depth. The FE drawbead model agrees well with the experiments whereas the analytical model overpredicted the drawbead forces.

  20. Aluminium. II - A review of deformation properties of high purity aluminium and dilute aluminium alloys.

    NASA Technical Reports Server (NTRS)

    Reed, R. P.

    1972-01-01

    The elastic and plastic deformation behavior of high-purity aluminum and of dilute aluminum alloys is reviewed. Reliable property data, including elastic moduli, elastic coefficients, tensile, creep, fatigue, hardness, and impact are presented. Single crystal tensile results are discussed. Rather comprehensive reference lists, containing publications of the past 20 years, are included for each of the above categories. Defect structures and mechanisms responsible for mechanical behavior are presented. Strengthening techniques (alloys, cold work, irradiation, quenching, composites) and recovery are briefly reviewed.

  1. The fracture of boron fibre-reinforced 6061 aluminium alloy

    NASA Technical Reports Server (NTRS)

    Wright, M. A.; Welch, D.; Jollay, J.

    1979-01-01

    The fracture of 6061 aluminium alloy reinforced with unidirectional and cross-plied 0/90 deg, 0/90/+ or - 45 deg boron fibres has been investigated. The results have been described in terms of a critical stress intensity, K(Q). Critical stress intensity factors were obtained by substituting the failure stress and the initial crack length into the appropriate expression for K(Q). Values were obtained that depended on the dimensions of the specimens. It was therefore concluded that, for the size of specimen tested, the values of K(Q) did not reflect any basic materials property.

  2. Foaming of aluminium-silicon alloy using concentrated solar energy

    SciTech Connect

    Cambronero, L.E.G.; Ruiz-Roman, J.M.; Canadas, I.; Martinez, D.

    2010-06-15

    Solar energy is used for the work reported here as a nonconventional heating system to produce aluminium foam from Al-Si alloy precursors produced by powder metallurgy. A commercial precursor in cylindrical bars enclosed in a stainless-steel mould was heated under concentrated solar radiation in a solar furnace with varied heating conditions (heating rate, time, and temperature). Concentrated solar energy close to 300 W/cm{sup 2} on the mould is high enough to achieve complete foaming after heating for only 200 s. Under these conditions, the density and pore distribution in the foam change depending on the solar heating parameters and mould design. (author)

  3. High rate constitutive modeling of aluminium alloy tube

    NASA Astrophysics Data System (ADS)

    Salisbury, C. P.; Worswick, M. J.; Mayer, R.

    2006-08-01

    As the need for fuel efficient automobiles increases, car designers are investigating light-weight materials for automotive bodies that will reduce the overall automobile weight. Aluminium alloy tube is a desirable material to use in automotive bodies due to its light weight. However, aluminium suffers from lower formability than steel and its energy absorption ability in a crash event after a forming operation is largely unknown. As part of a larger study on the relationship between crashworthiness and forming processes, constitutive models for 3mm AA5754 aluminium tube were developed. A nominal strain rate of 100/s is often used to characterize overall automobile crash events, whereas strain rates on the order of 1000/s can occur locally. Therefore, tests were performed at quasi-static rates using an Instron test fixture and at strain rates of 500/s to 1500/s using a tensile split Hopkinson bar. High rate testing was then conducted at rates of 500/s, 1000/s and 1500/s at 21circC, 150circC and 300circC. The generated data was then used to determine the constitutive parameters for the Johnson-Cook and Zerilli-Armstrong material models.

  4. Electromagnetic forming of aluminium alloy sheet

    NASA Astrophysics Data System (ADS)

    Oliveira, D. A.; Worswick, M.

    2003-09-01

    A numerical method for modeling the high rate deformation and impact that occurs during the electromagnetic forming process is presented with supporting experimental data, used to validate the predictions. The numerical model employs “loose" two-way coupling of the electromagnetic analysis with the elastic-plastic structural analysis. An electromagnetic finite element code is used to model the time varying currents that are discharged through the coil in order to obtain the transient magnetic forces that are imparted to the workpiece. The body forces generated by electromagnetic induction are then used as the loading condition to model the high rate deformation of the workpiece using an explicit dynamic finite element code. A series of high rate electromagnetic forming experiments are performed on 1 and 1.6 mm AA5754 and 1 mm AA5182 aluminum alloy sheet. The experiments consider free forming, while also serving as a basis to validate the predictive capability of the numerical models. The experiments exhibited high rate formability limits that were similar to conventional quasistatic forming limits. The numerical model accurately predicted the final geometry of the samples as well as the measured strain distributions.

  5. Frictional conditions between alloy AA6060 aluminium and tool steel

    SciTech Connect

    Wideroee, Fredrik; Welo, Torgeir

    2011-05-04

    The frictional conditions in the new process of screw extrusion of aluminium have been investigated. The contact behaviour between the aluminum alloy and the tool steel in the extruder is vital for understanding the extrusion process. Using a compressive-rotational method for frictional measurements the conditions for unlubricated sticking friction between aluminum alloy AA6060 and tool steel at different combinations of temperatures and pressures have been investigated. In this method the samples in the form of disks are put under hydrostatic pressure while simultaneously being rotated at one end. Pins made from contrast material have been inserted into the samples to measure the deformation introduced. This approach along with 3D simulations form a method for determining the frictional conditions. The paper describes the test method and the results. It was found that the necessary pressure for sticking to occur between the aluminum AA6060 and the different parts of the extruder is heavily influenced by the temperature.

  6. Thermoelectric power in low-density interstitial-free iron-aluminium alloys

    NASA Astrophysics Data System (ADS)

    Rana, Radhakanta; Liu, Cheng

    2013-09-01

    Thermoelectric power (TEP) studies on low-density interstitial-free iron-aluminium alloys reveal that the TEP decreases with increase in the aluminium content on account of the introduction of lattice dispersion centres. The TEP coefficients, determined from the Nordheim-Gorter law, for 6.8 and 8.1 wt.% aluminium additions to α-iron are found to be higher than values reported in previous literature for small aluminium additions. The grain size has a very weak effect on the TEP of these alloys.

  7. Performance of commercial aluminium alloys as anodes in gelled electrolyte aluminium-air batteries

    NASA Astrophysics Data System (ADS)

    Pino, M.; Chacón, J.; Fatás, E.; Ocón, P.

    2015-12-01

    The evaluation of commercial aluminium alloys, namely, Al2024, Al7475 and Al1085, for Al-air batteries is performed. Pure Al cladded Al2024 and Al7475 are also evaluated. Current rates from 0.8 mA cm-2 to 8.6 mA cm-2 are measured in a gel Al-air cell composed of the commercial alloy sample, a commercial air-cathode and an easily synthesizable gelled alkaline electrolyte. The influence of the alloying elements and the addition to the electrolyte of ZnO and ZnCl2, as corrosion inhibitors is studied and analysed via EDX/SEM. Specific capacities of up to 426 mAh/g are obtained with notably flat potential discharges of 1.3-1.4 V. The competition between self-corrosion and oxidation reactions is also discussed, as well as the influence of the current applied on that process. Al7475 is determined to have the best behaviour as anode in Al-air primary batteries, and cladding process is found to be an extra protection against corrosion at low current discharges. Conversely, Al1085 provided worse results because of an unfavourable metallic composition.

  8. The influence of alloy composition on residual stresses in heat treated aluminium alloys

    SciTech Connect

    Robinson, J.S.; Redington, W.

    2015-07-15

    The as quenched properties of eight different heat treatable aluminium alloys are related to residual stress magnitudes with the objective being to establish if there is a relationship between the residual stress and the as quenched alloy hardness and strength. Near surface residual stresses were assessed with X-ray diffraction using both the established sin{sup 2}ψ method and the more recent cos α technique. Through thickness residual stresses were also characterised using neutron diffraction. The alloys were chosen to encompass a wide range of strengths. The low to medium strength alloys were 6060 and 6082, medium to high strength 2618A, 2014A, 7075, 7010 and two variants of 7449, while the very high strength alloy was the powder metallurgy alloy N707. To assess the as quenched strength, dynamic hardness and tensile properties were determined from samples tested immediately after quenching to minimise the influence of precipitation hardening by natural aging. In addition, hot hardness measurements were made in situ on samples cooled to simulate quench paths. Within the experimental constraints of the investigation, the distribution of residual stress through the thickness was found to follow the same pattern for all the alloys investigated, varying from tensile in the interior to surface compression. The influence of alloy strength was manifested as a change in the observed residual stress magnitudes, and surface residual stresses were found to vary linearly with as quenched hardness and strength. - Highlights: • As quenched aluminium alloys contain high magnitude residual stresses. • Surface is compressive balance by a tensile core. • As quenched surface residual stress is linear function of alloy strength. • In situ hot hardness demonstrates rapid change in intrinsic hardness during rapid cooling.

  9. Microstructure and properties of hot compacted powders of aluminium alloys.

    PubMed

    Lityńska-Dobrzyńska, L; Dutkiewicz, J; Maziarz, W; Kanciruk, A

    2009-11-01

    Atomized 6061 aluminium alloy powders with and without the addition of 2 wt% Zr were milled for 80 h in a planetary ball mill and hot pressed in vacuum. The milled powders showed microhardness of about 170 HV, which increased after hot pressing up to 260 HV and up to 280 HV for powders without and with the Zr additions, respectively. Compression tests showed the high yield stress of 300 MPa obtained for the hot-pressed sample produced from the initial powders compared with ultimate compression strength of above 800 MPa for that of the milled sample and slightly higher for that with Zr additions. The effect of hot pressing on the structure of powders was investigated using a conventional analytical and high-resolution electron microscopy and high angle annular dark-field scanning transmission electron microscopy combined with energy dispersive X-ray microanalysis. The samples of initial powders hot pressed in vacuum showed a cell structure with particles of the Mg(2)Si and AlFeSi phases in intercell areas. In the milled and hot-pressed sample, the homogeneous structure of small grains of size below 200 nm was observed. The AlFeSi and Mg(2)Si particles with size 20-100 nm were uniformly distributed as well as the Zr rich particles in the Zr containing alloy. The Zr-rich particles containing up to 80 at% Zr were identified as a metastable fcc cubic phase with lattice parameter a= 0.48 nm.

  10. Modelling of Local Necking and Fracture in Aluminium Alloys

    NASA Astrophysics Data System (ADS)

    Achani, D.; Eriksson, M.; Hopperstad, O. S.; Lademo, O.-G.

    2007-05-01

    Non-linear Finite Element simulations are extensively used in forming and crashworthiness studies of automotive components and structures in which fracture need to be controlled. For thin-walled ductile materials, the fracture-related phenomena that must be properly represented are thinning instability, ductile fracture and through-thickness shear instability. Proper representation of the fracture process relies on the accuracy of constitutive and fracture models and their parameters that need to be calibrated through well defined experiments. The present study focuses on local necking and fracture which is of high industrial importance, and uses a phenomenological criterion for modelling fracture in aluminium alloys. As an accurate description of plastic anisotropy is important, advanced phenomenological constitutive equations based on the yield criterion YLD2000/YLD2003 are used. Uniaxial tensile tests and disc compression tests are performed for identification of the constitutive model parameters. Ductile fracture is described by the Cockcroft-Latham fracture criterion and an in-plane shear tests is performed to identify the fracture parameter. The reason is that in a well designed in-plane shear test no thinning instability should occur and it thus gives more direct information about the phenomenon of ductile fracture. Numerical simulations have been performed using a user-defined material model implemented in the general-purpose non-linear FE code LS-DYNA. The applicability of the model is demonstrated by correlating the predicted and experimental response in the in-plane shear tests and additional plane strain tension tests.

  11. New developments on optimizing properties of high-Zn aluminium cast alloys

    NASA Astrophysics Data System (ADS)

    Krajewski, W. K.; Buras, J.; Krajewski, P. K.; Greer, A. L.; Schumacher, P.; Haberl, K.

    2016-07-01

    Foundry alloys with Al-based matrices have a wide range of uses in today's global economy and there is a high demand for castings of Al alloys, including Al-Zn alloys. In this paper, investigations on the grain refinement of high-Zn aluminium cast alloys are presented. Aluminium alloys with relatively high zinc content have a tendency to be coarse-grained, especially in the case of castings with low cooling rates such as are found in sand moulds. The coarse-grained structure degrades the plasticity, specifically the elongation. Therefore, for aluminium alloys of high (10-30 wt.%) zinc content, inoculation is attractive, aiming to break up the primary dendrites of the a-phase solid solution of zinc in aluminium. Such dendrites are the principal microstructural component in these alloys. On the other hand, a finer grain structure usually reduces the damping (e.g. as measured by attenuation of ultrasound) in these alloys. In the present investigations, a binary sand-cast Al-20 wt.% Zn alloy was inoculated with different additions of AlTi3C0.15 (TiCAl) and ZnTi-based master alloys. The sand-cast samples were subjected to mechanical-property measurements (tensile strength and elongation), image analysis to determine grain size, and measurements of the attenuation of 1 MHz ultrasound. It is found that both of the master alloys used cause significant refinement of the a-AlZn primary dendrites and change their morphology from linear-branched to semi-globular, increase the elongation by about 40%, and decrease the attenuation coefficient by about 25% in comparison with the initial alloy without inoculation.

  12. Void growth in high strength aluminium alloy single crystals: a CPFEM based study

    NASA Astrophysics Data System (ADS)

    Asim, Umair; Siddiq, M. Amir; Demiral, Murat

    2017-04-01

    High strength aluminium alloys that are produced through forming and joining processes are widely used in aerospace components. The ductile failure in these metals occurs due to the evolution and accumulation of microscopic defects, such as microvoids and shear bands. The present work investigates the underlying physical mechanisms during ductile failure by performing a rigorous, fully-validated, three-dimensional crystal plasticity, finite element study with aluminium alloy single crystals. Representative volume element (RVE) based simulations of single crystalline aluminium alloys (AA-5xxx) with different void geometries and orientations have been performed. Both local and nonlocal crystal plasticity constitutive models have been implemented in a finite element framework and are used to seek new insights into the interrelationships among void growth, initial porosity, initial void size, plastic anisotropy, and local/nonlocal size effects.

  13. Self-Pierce Riveting of Three Aluminium Alloy and Mild Steel Sheets

    SciTech Connect

    Mori, K.; Abe, Y.; Sakai, S.; Kato, T.

    2010-06-15

    Three aluminium alloy and steel sheets were joined with a self-piercing rivet. Self-pierce riveting has the function of joining steel and aluminium alloys having very different melting points due to plastic joining. The requisites for joining the three sheets are the driving of the rivet leg through the middle sheet, the flaring of the rivet leg in the lower sheet and the prevention of the fracture of the lower sheet. The joinability for various combinations of the three sheets was determined. When the rivet leg is small, no driving through the middle sheet occurs, the lower sheet ruptures for a large rivet leg. In addition, 980 MPa high strength steel, mild steel and aluminium alloy sheets were joined by the self-pierce riveting.

  14. Self-Pierce Riveting of Three Aluminium Alloy and Mild Steel Sheets

    NASA Astrophysics Data System (ADS)

    Mori, K.; Abe, Y.; Kato, T.; Sakai, S.

    2010-06-01

    Three aluminium alloy and steel sheets were joined with a self-piercing rivet. Self-pierce riveting has the function of joining steel and aluminium alloys having very different melting points due to plastic joining. The requisites for joining the three sheets are the driving of the rivet leg through the middle sheet, the flaring of the rivet leg in the lower sheet and the prevention of the fracture of the lower sheet. The joinability for various combinations of the three sheets was determined. When the rivet leg is small, no driving through the middle sheet occurs, the lower sheet ruptures for a large rivet leg. In addition, 980 MPa high strength steel, mild steel and aluminium alloy sheets were joined by the self-pierce riveting.

  15. HRTEM and HAADF-STEM of precipitates at peak ageing of cast A319 aluminium alloy.

    PubMed

    Wiengmoon, Amporn; Pearce, John T H; Chairuangsri, Torranin; Isoda, Seiji; Saito, Hikaru; Kurata, Hiroki

    2013-02-01

    High-resolution transmission electron microscopy (HRTEM) and high-angle annular-dark-field scanning transmission electron microscopy (HAADF-STEM) were applied to investigate the precipitates formed during age hardening at 170±5°C for up to 48h of cast A319 aluminium alloy (Al-4.93wt%Si-3.47wt%Cu). The precipitates at the peak-aged condition have been identified as mainly θ" together with a smaller amount of θ'. It is proposed that the θ" is responsible for hardening at peak ageing at 170°C of the cast A319 aluminium alloy.

  16. Silica mesoporous thin films as containers for benzotriazole for corrosion protection of 2024 aluminium alloys

    NASA Astrophysics Data System (ADS)

    Recloux, Isaline; Mouanga, Maixent; Druart, Marie-Eve; Paint, Yoann; Olivier, Marie-Georges

    2015-08-01

    This work contributes to the development of a new environmentally friendly alternative pretreatment for 2024 aluminium alloys to replace hexavalent chromium based conversion layers in the aeronautical field. A silica mesoporous thin film, synthesized through the evaporation induced self-assembly process, was doped with benzotriazole to obtain active corrosion protection. Inhibitor loading contents were correlated with pore characteristics. The release kinetics was studied as function of pH. The application of the doped mesoporous film on 2024 aluminium alloy revealed a slowing down of corrosion processes, demonstrating its potential as an active inhibitor storage layer.

  17. Steam assisted oxide growth on aluminium alloys using oxidative chemistries: Part II corrosion performance

    NASA Astrophysics Data System (ADS)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    2015-11-01

    Surface treatment of aluminium alloys using steam with oxidative chemistries, namely KMnO4 and HNO3 resulted in accelerated growth of oxide on aluminium alloys. Detailed investigation of the corrosion performance of the treated surfaces was carried out using potentiodynamic polarisation and standard industrial test methods such as acetic acid salt spray (AASS) and filiform corrosion on commercial AA6060 alloy. Barrier properties of the film including adhesion were evaluated using tape test under wet and dry conditions. Electrochemical results showed reduced cathodic and anodic activity, while the protection provided by steam treatment with HNO3 was a function of the concentration of NO3- ions. The coating generated by inclusion of KMnO4 showed highest resistance to filiform corrosion. Overall, the performance of the steam treated surfaces under filiform corrosion and AASS test was a result of the local coverage of the alloy microstructure resulting from steam containing with KMnO4 and HNO3.

  18. Evaluation Of Four Welding Arc Processes Applied To 6061 Aluminium Alloy

    SciTech Connect

    Benoit, A.; Paillard, P.; Baudin, T.; Jobez, S.; Castagne, J.-F.

    2011-01-17

    At a time when greenhouse gas emissions must be reduced, the use of the aluminium alloys is expanding, in particular in the transportation industry. In order to extend the possibilities of aluminium assembly design, new Metal Inert Gas (MIG) welding processes have been conceived. They work at lower temperatures than usual arc processes (classic MIG or Tungsten Inert Gas). This study compares four arc welding processes, applied to the 6061 aluminium alloy. These four weld processes have been studied through the metallurgical analysis of the weld beads. Metallography, micro-hardness testings, X Ray radiography have been carried out on the produced weld beads. The processes are classified according to the quality of the beads like geometry of beads, size of the heat affected zone and presence of defects.

  19. Property enhancement by grain refinement of zinc-aluminium foundry alloys

    NASA Astrophysics Data System (ADS)

    Krajewski, W. K.; Greer, A. L.; Piwowarski, G.; Krajewski, P. K.

    2016-03-01

    Development of cast alloys with good mechanical properties and involving less energy consumption during their melting is one of the key demands of today's industry. Zinc foundry alloys of high and medium Al content, i.e. Zn-(15-30) wt.% Al and Zn-(8-12) wt.% Al, can satisfy these requirements. The present paper summarizes the work [1-9] on improving properties of sand-cast ZnAl10 (Zn-10 wt.% Al) and ZnAl25 (Zn-25 wt. % Al) alloys by melt inoculation. Special attention was devoted to improving ductility, whilst preserving high damping properties at the same time. The composition and structural modification of medium- and high-aluminium zinc alloys influence their strength, tribological properties and structural stability. In a series of studies, Zn - (10-12) wt. % Al and Zn - (25-26) wt.% Al - (1-2.5) wt.% Cu alloys have been doped with different levels of added Ti. The melted alloys were inoculated with ZnTi-based refiners and it was observed that the dendritic structure is significantly finer already after addition of 50 - 100 ppm Ti to the melted alloys. The alloy's structure and mechanical properties have been studied using: SEM (scanning electron microscopy), LM (light microscopy), dilatometry, pin-on-disc wear, and tensile strength measurements. Grain refinement leads to significant improvement of ductility in the binary high-aluminium Zn-(25-27) Al alloys while in the medium-aluminium alloys the effect is rather weak. In the ternary alloys Zn-26Al-Cu, replacing a part of Cu with Ti allows dimensional changes to be reduced while preserving good tribological properties. Furthermore, the high initial damping properties were nearly entirely preserved after inoculation. The results obtained allow us to characterize grain refinement of the examined high-aluminium zinc alloys as a promising process leading to the improvement of their properties. At the same time, using low melting ZnTi-based master alloys makes it possible to avoid the excessive melt overheating

  20. Recovery of aluminium, nickel-copper alloys and salts from spent fluorescent lamps.

    PubMed

    Rabah, Mahmoud A

    2004-01-01

    This study explores a combined pyro-hydrometallurgical method to recover pure aluminium, nickel-copper alloy(s), and some valuable salts from spent fluorescent lamps (SFLs). It also examines the safe recycling of clean glass tubes for the fluorescent lamp industry. Spent lamps were decapped under water containing 35% acetone to achieve safe capture of mercury vapour. Cleaned glass tubes, if broken, were cut using a rotating diamond disc to a standard shorter length. Aluminium and copper-nickel alloys in the separated metallic parts were recovered using suitable flux to decrease metal losses going to slag. Operation variables affecting the quality of the products and the extent of recovery with the suggested method were investigated. Results revealed that total loss in the glass tube recycling operation was 2% of the SFLs. Pure aluminium meeting standard specification DIN 1712 was recovered by melting at 800 degrees C under sodium chloride/carbon flux for 20 min. Standard nickel-copper alloys with less than 0.1% tin were prepared by melting at 1250 degrees C using a sodium borate/carbon flux. De-tinning of the molten nickel-copper alloy was carried out using oxygen gas. Tin in the slag as oxide was recovered by reduction using carbon or hydrogen gas at 650-700 degrees C. Different valuable chloride salts were also obtained in good quality. Further research is recommended on the thermodynamics of nickel-copper recovery, yttrium and europium recovery, and process economics.

  1. Recovery of aluminium, nickel-copper alloys and salts from spent fluorescent lamps

    SciTech Connect

    Rabah, Mahmoud A

    2004-07-01

    This study explores a combined pyro-hydrometallurgical method to recover pure aluminium, nickel-copper alloy(s), and some valuable salts from spent fluorescent lamps (SFLs). It also examines the safe recycling of clean glass tubes for the fluorescent lamp industry. Spent lamps were decapped under water containing 35% acetone to achieve safe capture of mercury vapour. Cleaned glass tubes, if broken, were cut using a rotating diamond disc to a standard shorter length. Aluminium and copper-nickel alloys in the separated metallic parts were recovered using suitable flux to decrease metal losses going to slag. Operation variables affecting the quality of the products and the extent of recovery with the suggested method were investigated. Results revealed that total loss in the glass tube recycling operation was 2% of the SFLs. Pure aluminium meeting standard specification DIN 1712 was recovered by melting at 800 deg. C under sodium chloride/carbon flux for 20 min. Standard nickel-copper alloys with less than 0.1% tin were prepared by melting at 1250 deg. C using a sodium borate/carbon flux. De-tinning of the molten nickel-copper alloy was carried out using oxygen gas. Tin in the slag as oxide was recovered by reduction using carbon or hydrogen gas at 650-700 deg. C. Different valuable chloride salts were also obtained in good quality. Further research is recommended on the thermodynamics of nickel-copper recovery, yttrium and europium recovery, and process economics.

  2. Identification of monoclinic θ-phase dispersoids in a 6061 aluminium alloy

    NASA Astrophysics Data System (ADS)

    Buchanan, Karl; Ribis, Joël; Garnier, Jérôme; Colas, Kimberly

    2016-04-01

    Intermetallic dispersoids play an important role in controlling the 6xxx alloy series' grain distribution and increasing the alloy's toughness. The dispersoid distribution in a 6061 aluminium alloy (Al-Mg-Si) was analysed by transmission electron microscopy, selected area diffraction and energy-dispersive X-ray spectroscopy. The dispersoids had three unique crystal structures: simple cubic ?, body-centred cubic ? and monoclinic (C2/m). While the SC and BCC dispersoids have been well characterized in the literature, a detailed analysis of monoclinic dispersoids has not been presented. Therefore, the current work discusses the chemical composition, crystal structure and morphology of the monoclinic dispersoids.

  3. Steam assisted oxide growth on aluminium alloys using oxidative chemistries: Part I Microstructural investigation

    NASA Astrophysics Data System (ADS)

    Din, Rameez Ud; Piotrowska, Kamila; Gudla, Visweswara Chakravarthy; Jellesen, Morten Stendahl; Ambat, Rajan

    2015-11-01

    The surface treatment of aluminium alloys under steam containing KMnO4 and HNO3 resulted in the formation of an oxide layer having a thickness of up to 825 nm. The use of KMnO4 and HNO3 in the steam resulted in incorporation of the respective chemical species into the oxide layer. Steam treatment with solution containing HNO3 caused dissolution of Cu and Si from the intermetallic particles in the aluminium substrate. The growth rate of oxide layer was observed to be a function of MnO4- and NO3- ions present in the aqueous solution. The NO3- ions exhibit higher affinity towards the intermetallic particles resulting in poor coverage by the steam generated oxide layer compared to the coating formed using MnO4- ions. Further, increase in the concentration of NO3- ions in the solution retards precipitation of the steam generated aluminium hydroxide layer.

  4. Electrodeposition of iron and iron-aluminium alloys in an ionic liquid and their magnetic properties.

    PubMed

    Giridhar, P; Weidenfeller, B; El Abedin, S Zein; Endres, F

    2014-05-28

    In this work we show that nanocrystalline iron and iron-aluminium alloys can be electrodeposited from the ionic liquid 1-butyl-1-methylpyrrolidinium trifluoromethylsulfonate, [Py1,4]TfO, at 100 °C. The study comprises CV, SEM, XRD, and magnetic measurements. Two different sources of iron(ii) species, Fe(TfO)2 and FeCl2, were used for the electrodeposition of iron in [Py1,4]TfO. Cyclic voltammetry was employed to evaluate the electrochemical behavior of FeCl2, Fe(TfO)2, and (FeCl2 + AlCl3) in the employed ionic liquid. Thick iron deposits were obtained from FeCl2/[Py1,4]TfO at 100 °C. Electrodeposition of iron-aluminium alloys was successful in the same ionic liquid at 100 °C. The morphology and crystallinity of the obtained deposits were investigated using SEM and XRD, respectively. XRD measurements reveal the formation of iron-aluminium alloys. First magnetic measurements of some deposits gave relatively high coercive forces and power losses in comparison to commercial iron-silicon samples due to the small grain size in the nanometer regime. The present study shows the feasibility of preparing magnetic alloys from ionic liquids.

  5. Revealing obliterated engraved marks on high strength aluminium alloy (AA7010) surfaces by etching technique.

    PubMed

    Bong, Yeu Uei; Kuppuswamy, R

    2010-02-25

    Restoration of obliterated engraved marks on high strength Al-Zn-Mg-Cu alloy (AA7010) surfaces by etching technique was studied. The alloy surfaces were mechanically engraved with some identification marks using "Gravograph". The marks were then erased by removing the metal to different levels up to and below the depth of engraving. Five metallographic reagents were tested on the obliterated surfaces by etching. The following two methods (i) immersion in 10% aq. phosphoric acid and (ii) alternate swabbing of 60% HCl and 40% NaOH were found to be quite effective to reveal the obliterated marks. These two procedures were also able to show effectively the marks obliterated by over-engraving and centre punching. Of the two techniques immersion in phosphoric acid provided more contrast. Interestingly, alternate swabbing of 60% HCl and 40% NaOH presented itself to be the common reagent for restoration on pure aluminium as well as its alloy surfaces. This is evident from our own current experiments and those of earlier researchers [G. Peeler, S. Gutowski, H. Wrobel, G. Dower, The restoration of impressed characters on aluminium alloy motor cycle frames, J. Forensic Ident. 58 (1) (2008) 27-32; M. Izhar M. Baharum, R. Kuppuswamy, A.A. Rahman, Restoration of engraved marks on aluminium surfaces by etching technique, Forensic Sci. Int. 177 (2008) 221-227]. The findings have assumed importance as engines and chassis of cars and frames of firearms are currently made of high strength aluminium alloys and recovery on these surfaces by current methods is not satisfactory.

  6. Performance of AA5052 alloy anode in alkaline ethylene glycol electrolyte with dicarboxylic acids additives for aluminium-air batteries

    NASA Astrophysics Data System (ADS)

    Wang, DaPeng; Zhang, DaQuan; Lee, KangYong; Gao, LiXin

    2015-11-01

    Dicarboxylic acid compounds, i.e. succinic acid (SUA), adipic acid (ADA) and sebacic acid (SEA), are used as electrolyte additives in the alkaline ethylene glycol solution for AA5052 aluminium-air batteries. It shows that the addition of dicarboxylic acids lowers the hydrogen gas evolution rate of commercial AA5052 aluminium alloy anode. AA5052 aluminium alloy has wide potential window for electrochemical activity and better discharge performance in alkaline ethylene glycol solution containing dicarboxylic acid additives. ADA has the best inhibition effect for the self-corrosion of AA5052 anode among the three dicarboxylic acid additives. Fourier transform infrared spectroscopy (FT-IR) reveals that dicarboxylic acids and aluminium ions can form coordination complexes. Quantum chemical calculations shows that ADA has a smaller energy gap (ΔE, the energy difference between the lowest unoccupied orbital and the highest occupied orbital), indicating that ADA has the strongest interaction with aluminium ions.

  7. Study of solid-solution hardening in binary aluminium-based alloys

    NASA Astrophysics Data System (ADS)

    Draissia, Mohamed; Debili, Mohamed-Yacine

    2005-09-01

    Solid-solution formation in binary aluminium-based alloys is due essentially to the combined effects of the size and valence of solvent and solute atoms, as expected by the four Hume-Rothery rules. The lattice parameter of aluminium in the solid solution of the sputtered Al-Fe films is [Al-a (Å)=4.052-6.6×10-3Y]. The increasing and decreasing evolution of the lattice parameter of copper [Cu-a (Å)=3.612+1.8×10-3Z] and aluminium [Al-a (Å)=4.048-1.6×10-3X] in the sputtered Al-1.8 to 92.5 at. % Cu films is a result of the difference in size between the aluminium and copper atoms. The low solubility of copper in aluminium (<1.8 at % Cu) is due to the valences of solvent and solute atoms in contrast with other sputtered films prepared under similar conditions, such as Al-Mg (20 at. % Mg), Al-Ti (27 at. % Ti), Al-Cr (5at. % Cr) and Al-Fe (5.5 at. % Fe) where the solubility is due to the difference in size.

  8. Aluminium alloys with transition metals prepared by powder metallurgy

    NASA Astrophysics Data System (ADS)

    Kucera, V.; Prusa, F.; Vojtech, D.

    2017-02-01

    Powder metallurgy represented by mechanical alloying and spark plasma sintering was used for preparation of the AlFe16 and the AlSi20Fe16 alloys. Microstructure of the both alloys consisted of very fine intermetallic phases homogenously dispersed in the matrix of α-Al solid solution. Fine nature of microstructure led to promising results of compressive stress-strain tests performed at laboratory and elevated temperature of 400 °C. The compressive strengths of the AlSi20Fe16 and the AlFe16 alloys at laboratory temperature were 780 MPa and 508 MPa, respectively. Elevated temperature resulted in drop of the compressive strengths to 480 MPa and 211 MPa, respectively. However, the results of investigated alloys outperformed the thermally stable AlSi12Cu1Mg1Ni1 (wt. %) used as reference material.

  9. Two-Scale Modelling of Effects of Microstructure and Thermomechanical Properties on Dynamic Performance of an Aluminium Alloy

    DTIC Science & Technology

    2010-09-01

    monolithic metallic plate fabricated from a precipitate-strengthened aluminium alloy . The alloy of study is Al 2139, consisting primarily of elemental Al...polycrystalline Al-Cu-Mg alloy . A limited number of experiments have been conducted to assess ductility, fracture strength and high -rate behaviour of...effects of crystallographic texture on the high -rate shear response of a Ti-6Al-4V alloy . Schoenfeld and Kad (2002) found that lattice orientations affect

  10. Measurement research for pitting potential of aluminium alloy with chromate passivation layers

    NASA Astrophysics Data System (ADS)

    Su, Z. H.; Dai, Y.; Ma, Q. Y.; Wang, J. N.; Zheng, C. Q.

    2017-01-01

    This paper describes common technology for measuring corrosion resistant properties of aluminium alloy with chromate passivation layers. It gives a resolution to characterize corrosion resistant properties of pitting potential. The method, including sample preparation, measuring polarization and the determining of pitting corrosion potential, was proposed. Tests of repeatability and reproducibility can meet the demand of measurement precision. In addition, comparison of the positional relationships between polarization curves and nominal pitting corrosion potential was provided to judge products.

  11. TEM and HRTEM studies of ball milled 6061 aluminium alloy powder with Zr addition.

    PubMed

    Lityńska-Dobrzyńska, L; Dutkiewicz, J; Maziarz, W; Rogal, Ł

    2010-03-01

    The effect of mechanical alloying on the microstructure of atomized 6061 aluminium alloy powder and 6061 powder with a zirconium addition was studied in the work. The atomized 6061 aluminium alloy powder and 6061 powder with addition of 2 wt.% Zr were milled in a planetary ball mill and investigated using X-ray diffraction measurements, conventional and high-resolution electron microscopy (TEM/HRTEM) and high-angle annular dark field scanning transmission electron microscopy combined with energy dispersive X-ray microanalysis. An increase of stresses was observed in milled powders after the refinement of crystallites beyond 100 nm. In the powder with zirconium addition, some part of the Zr atoms diffused in aluminium forming a solid solution containing up to 0.5 wt.% Zr. The remaining was found to form Zr-rich particles containing up to 88 wt.% Zr and were identified as face centred cubic (fcc) phase with lattice constant a= 0.48 nm. That fcc phase partially transformed into the L1(2) ordered phase. Eighty-hour milling brought an increase of microhardness (measured with Vickers method) from about 50 HV (168 MPa) for the initial 6061 powder to about 170 HV (552 MPa). The addition of zirconium had no influence on the microhardness.

  12. Protection of 2024-T3 aluminium alloy by corrosion resistant phytic acid conversion coating

    NASA Astrophysics Data System (ADS)

    Shi, Hongwei; Han, En-Hou; Liu, Fuchun; Kallip, Silvar

    2013-09-01

    The corrosion protection properties of environmentally friendly phytic acid conversion coatings were studied on 2024-T3 aluminium alloy. The films were prepared under acidic conditions with various pH values and characterised by SEM, EDS, ATR-FTIR and electrochemical techniques. The results indicate that the conversion coatings obtained by immersing the alloy in phytic acid solutions at pH from 3 to 5.5 provide excellent corrosion resistance. ATR-FTIR confirms that the film is formed by deposition of reaction products between Al3+ and phosphate groups in phytic acid molecules. The conformation models of the deposition film are proposed.

  13. High-Rate Compaction of Aluminium Alloy Foams

    NASA Astrophysics Data System (ADS)

    Harrigan, J. J.; Hung, Y.-C.; Tan, P. J.; Bourne, N. K.; Withers, P. J.; Reid, S. R.; Millett, J. C. F.; Milne, A. M.

    2006-07-01

    The response of aluminium foams to impact can be categorised according to the impact velocity. Tests have been carried out at a range of impact velocities from quasi-static to velocities approaching the speed of sound in the foam. Various experimental arrangements have been employed including pneumatic launcher tests and plate impact experimants at velocities greater than 1000 m s-1. The quasi-static compression behaviour was approximately elastic, perfectly-plastic, locking. For static and dynamic compression at low impact velocities the deformation pattern was through the cumulative multiplication of discrete, non-contiguous crush bands. Selected impact tests are presented here for which the impact velocity is less than the velocity of sound, but above a certain critical impact velocity so that the plastic compression occurs in a shock-like manner and the specimens deform by progressive cell crushing. Laboratory X-ray microtomography has been employed to acquire tomographic datasets of aluminium foams before and after tests. The morphology of the underformed foam was used as the input dataset to an Eulerian code. Hydrocode simulations were then carried out on a real microstructure. These simulations provide insight to mechanisms associated with the localization of deformation.

  14. High-Rate Compaction of Aluminium Alloy Foams

    NASA Astrophysics Data System (ADS)

    Harrigan, J. J.; Millett, J. C. F.; Milne, A. M.

    2005-07-01

    The response of aluminium foams to impact can be categorised by the impact velocity. Tests are reported ranging from quasi-static to impact velocities greater than the speed of sound in the foam. The techniques used ranging from drop-hammer and pneumatic launcher tests, to plate impact at velocities greater than 1000 m s-1. The quasi-static compression behaviour was elastic, perfectly-plastic, locking. For static and dynamic compression at low impact velocities, post-impact examination of partially crushed specimens showed that deformation was through the cumulative multiplication of crush bands. If the impact velocity is less than the velocity of sound, but above a certain critical impact velocity, the plastic compression occurs in a shock-like manner and the specimens deform by progressive cell crushing. At higher impact velocities the compaction front is not preceded by an elastic wave. Laboratory X-ray microtomography has been employed to acquire tomographic datasets of aluminium foams before and after tests. The morphology of the underformed foam was input as the input dataset to an Eulerian code. Hydrocode simulations were then carried out on real microstructure. These simulations provide insight to mechanisms associated with the localization of deformation.

  15. High-Rate Compaction of Aluminium Alloy Foams

    SciTech Connect

    Harrigan, J. J.; Hung, Y.-C.; Tan, P. J.; Bourne, N. K.; Withers, P. J.; Reid, S. R.; Millett, J. C. F.; Milne, A. M.

    2006-07-28

    The response of aluminium foams to impact can be categorised according to the impact velocity. Tests have been carried out at a range of impact velocities from quasi-static to velocities approaching the speed of sound in the foam. Various experimental arrangements have been employed including pneumatic launcher tests and plate impact experimants at velocities greater than 1000 m s-1. The quasi-static compression behaviour was approximately elastic, perfectly-plastic, locking. For static and dynamic compression at low impact velocities the deformation pattern was through the cumulative multiplication of discrete, non-contiguous crush bands. Selected impact tests are presented here for which the impact velocity is less than the velocity of sound, but above a certain critical impact velocity so that the plastic compression occurs in a shock-like manner and the specimens deform by progressive cell crushing. Laboratory X-ray microtomography has been employed to acquire tomographic datasets of aluminium foams before and after tests. The morphology of the underformed foam was used as the input dataset to an Eulerian code. Hydrocode simulations were then carried out on a real microstructure. These simulations provide insight to mechanisms associated with the localization of deformation.

  16. Precipitation, strength and work hardening of age hardened aluminium alloys

    NASA Astrophysics Data System (ADS)

    Ryen, Ø.; Holmedal, B.; Marthinsen, K.; Furu, T.

    2015-08-01

    The strength and work hardening of age hardened AA6063 and AA6082 alloys have been investigated in terms of a detailed characterization of precipitate and dislocation structures obtained by TEM and SEM. Tensile and compression tests were performed at as quenched, peak aged and severely aged conditions. A strong work hardening in the as quenched condition was found, similar to AlMg alloys with twice as much alloying elements in solid solution. It was found that the initial work hardening rate and the critical failure strain are both smallest at the peak aged condition. During large deformations the needle-shaped precipitates are sheared uniformly by dislocations altering their <001> orientations, which indicates extensive cross slip. In the overaged condition the early initial work hardening is larger than at the peak aged condition, but followed by a weak linear work hardening, apparently directly entering stage IV at a low strain. Cracked, needle-shaped precipitates were seen at larger strains.

  17. On the micromechanisms responsible for bilinearity in fatigue power-law relationships in aluminium-lithium alloys

    SciTech Connect

    Prasad, N.E.; Malakondaiah, G.; Kutumbarao, V.V.

    1997-09-01

    Aluminium-lithium alloys, like many other aerospace structural alloys, exhibit bilinearity in power-law relationships between high strain, low cycle fatigue life (in terms of number of reversals to failure, 2N{sub f}) and plastic strain amplitude ({Delta}{epsilon}{sub p}/2) or average stress amplitude ({Delta}{sigma}/2) or average plastic strain energy per cycle ({Delta}W{sub p}). In the present paper the micromechanisms leading to bilinear fatigue power-law relationships, especially the Coffin-Manson (C-M) relationship, in aluminium-lithium alloys are compiled and discussed.

  18. Cavitation erosion resistance of microarc oxidation coating on aluminium alloy

    NASA Astrophysics Data System (ADS)

    Cheng, Feng; Jiang, Shuyun; Liang, Jun

    2013-09-01

    Two ceramic coatings are prepared on 2124 aluminum alloy by microarc oxidation (MAO) technology. To explore the cavitation erosion resistance of the MAO coating, cavitation tests were performed by using a rotating-disk test rig. The mass losses, surface morphologies, chemical compositions and the phase constituents of the samples after cavitation tests were examined by using digital balance, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD), respectively. The results indicate that the MAO coatings can extend the incubation period of aluminum alloy, and thus enhance the cavitation erosion resistance as compared to the untreated aluminum alloy samples. After duration of 63 h cavitation test, a lot of erosion pits and the particles in various shapes can be observed on the surfaces of the aluminum alloy samples, while only a few erosion pits are observed on the MAO coatings. Moreover, the mean depths of erosion on the MAO coatings are lower in the first 30 h and are independent on erosion time. The results show that the cavitation erosion of MAO coating is governed by water mechanical impaction, resulting from the effects of brittle fracture of the MAO coating.

  19. A hybrid aluminium alloy and its zoo of interacting nano-precipitates

    SciTech Connect

    Wenner, Sigurd; Marioara, Calin Daniel; Andersen, Sigmund Jarle; Ervik, Martin; Holmestad, Randi

    2015-08-15

    An alloy with aluminium as its base element is heat treated to form a multitude of precipitate phases known from different classes of industrial alloys: Al–Cu(–Mg), Al–Mg–Si–Cu, and Al–Zn–Mg. Nanometer-sized needle-shaped particles define the starting point of the phase nucleation, after which there is a split in the precipitation sequence into six phases of highly diverse compositions and morphologies. There are several unique effects of phases from different alloy systems being present in the same host lattice, of which we concentrate on two: the replacement of Ag by Zn on the Ω interface and the formation of combined plates of the θ′ and C phases. Using atomically resolved scanning transmission electron microscopy and energy-dispersive X-ray spectroscopy, we investigate the formation mechanisms, crystal structures and compositions of the precipitates. - Graphical abstract: Display Omitted - Highlights: • An aluminium alloy composition in-between the 2/6/7xxx systems was investigated. • Six different phases from the three systems coexist in an over-aged state. • All phases with 〈001〉{sub Al} coherencies can nucleate on 6xxx needle precipitates. • Modified theta′ and omega interfaces are observed.

  20. Analysis of wear properties of aluminium based journal bearing alloys with and without lubrication.

    NASA Astrophysics Data System (ADS)

    Mathavan, J. Joy; Patnaik, Amar

    2016-09-01

    Apart from classical bearing materials, Aluminium alloys are used as bearing materials these days because of their superior quality. In this analysis, new Aluminium based bearing materials, with filler metals Si, Ni, and Cr are prepared by metal mould casting in burnout furnace machine, and tribological properties of these alloys with and without lubrication were tested. The experiments for wear with lubrication are conducted on multiple specimen tester and experiments without lubrication is conducted on Pin on disk tribometer. The disc material used was SAE 1050 steel. Wear tests were conducted at a sliding speed of 0.785 m/s and at a normal load of 20 N. Coefficient of friction values, temperature changes and wear of the specimens were plotted on graph according to the above mentioned working conditions. Hardness and weight losses of the specimens were calculated. The obtained results demonstrate how the friction and wear properties of these samples have changed with the % addition of Silicon, Chromium and Nickel to the base metal aluminium.

  1. Study of surface interactions of ionic liquids with aluminium alloys in corrosion and erosion corrosion processes

    NASA Astrophysics Data System (ADS)

    Bermúdez, María-Dolores; Jiménez, Ana-Eva; Martínez-Nicolás, Ginés

    2007-06-01

    Surface interactions of alkylimidazolium ionic liquids (ILs) with aluminium alloy Al 2011 have been studied by immersion tests in seven neat ILs [1- n-alkyl-3-methylimidazolium X - (X = BF 4; n = 2 (IL1), 6 (IL2), 8 (IL3). X = CF 3SO 3; n = 2 (IL4). X = (4-CH 3C 6H 4SO 3); n = 2 (IL5). X = PF 6; n = 6 (IL6)] and 1-butyl-3-methylpyridinium bis(trifluoromethylsulfonyl)imide (IL7)]. Immersion tests for Al 2011 have also been carried out in 1 wt.% and 5 wt.% solutions of 1-ethyl,3-methylimidazolium tetrafluoroborate (IL1) in water. No corrosion of Al 2011 by neat ILs is observed. The highest corrosion rate for Al 2011 in water is observed in the presence of a 5 wt.% IL1 due to hydrolysis of the anion with hydrogen evolution and formation of aluminium fluoride. Erosion-corrosion processes have been studied for three aluminium alloys (Al 2011, Al 6061 and Al 7075) in a 90 wt.% IL1 solution in water in the presence of α-alumina particles. The erosion-corrosion rates are around 0.2 mm/year or lower, and increase with increasing copper content to give a corrosion resistance order of Al 6061 > Al 7075 > Al 2011. Results are discussed on the basis of scanning electron microscopy (SEM) observations, energy dispersive spectroscopy (EDS) analysis, X-ray diffraction (XRD) patterns and X-ray photoelectron spectroscopy (XPS) determinations.

  2. Study on optimal surface property of WC-Co cutting tool for aluminium alloy cutting

    NASA Astrophysics Data System (ADS)

    Nizar, Mohd; Arimatsu, Naoya; Kawamitsu, Hiroshi; Takai, Kazuteru; Fukumoto, Masahiro

    2016-02-01

    The light weight property as well as high corrosion resistance of aluminium alloy has increased their demand especially in automobile industries. Aluminium alloy as a matter of fact has a low melting point and high ductility that severely adhere to the cutting tool surface and cause deterioration of chip evacuation. This problem often resulting in tools breakage. In this paper, in order to impart functions of anti-adhesion, we propose a technique by controlling the grinding marks micro texture on the tool surface by using the blast polishing treatment without any coating technologies. The results show that the tool which underwent polishing treatment reduces the cutting force as well as the aluminium adherence during the initial cutting process, and become worst as the process cutting continues. These results indicate that grinding mark texture improves the anti-adhesion by reducing the contact area during cutting and provide storage for the lubricant. In addition, too much polishing on the tool surface may remove these textures and resultantly worsen the tool performance.

  3. Surface formation in direct chill (DC) casting of 6082 aluminium alloys

    NASA Astrophysics Data System (ADS)

    Bayat, N.; Carlberg, T.

    2016-03-01

    Surface defects in aluminium billet production are a real problem for the subsequent extrusion procedure. Extrusion productivity can be influenced by the surface properties, which is defined as surface appearance, surface segregation zone depth and large Mg2Si and β-particles (Al5FeSi). In this research the surface formation during DC casting of 6082 aluminium billets produced by the air slip technology is studied. The surface microstructures of 6082 aluminium alloys with smooth and wavy surface appearances were investigated, including segregation zone depths and phase formation. The results were discussed based on the exudation of liquid metal through the mushy zone. The specific appearance of the wavy surface of 6082 alloys was correlated to how the oxide skin adheres to the underlying mushy zone and coupled to the dendritic coherency and surface tension of the skin. The occurrence of different phases at the very surface and in the layer just below was explained by variations in solidification directions and subsequent segregation patterns.

  4. The fatigue response of the aluminium-lithium alloy, 8090

    NASA Technical Reports Server (NTRS)

    Birt, M. J.; Beevers, C. J.

    1989-01-01

    The fatigue response of an Al-Li-Cu-Mg-Zr (8090) alloy has been studied at room temperature. The initiation and growth of small and long cracks has been examined at R = 0.1 and at a frequency of 100 Hz. Initiation was observed to occur dominantly at sub-grain boundaries. The growth of the small cracks was crystallographic in character and exhibited little evidence of retardation or arrest at the grain boundaries. The long crack data showed the alloy to have a high resistance to fatigue crack growth with underaging providing the optimum heat treatment for fatigue crack growth resistance. In general, this can be attributed to high levels of crack closure which resulted from the presence of extensive microstructurally related asperities.

  5. Finite Element Analysis of Warpage in Laminated Aluminium Alloy Plates for Machining of Primary Aeronautic Parts

    SciTech Connect

    Reis, A. C.; Moreira Filho, L. A.; Menezes, M. A.

    2007-04-07

    The aim of this paper consists in presenting a method of simulating the warpage in 7xxx series aluminium alloy plates. To perform this simulation finite element software MSC.Patran and MSC.Marc were used. Another result of this analysis will be the influence on material residual stresses induced on the raw material during the rolling process upon the warpage of primary aeronautic parts, fabricated through machining (milling) at Embraer. The method used to determinate the aluminium plate residual stress was Layer Removal Test. The numerical algorithm Modified Flavenot Method was used to convert layer removal and beam deflection in stress level. With such information about the level and profile of residual stresses become possible, during the step that anticipate the manufacturing to incorporate these values in the finite-element approach for modelling warpage parts. Based on that warpage parameter surely the products are manufactured with low relative vulnerability propitiating competitiveness and price.

  6. Fabrication of self-healing super-hydrophobic surfaces on aluminium alloy substrates

    SciTech Connect

    Wang, Yang; Wei Liu, Xiao; Zhang, Hai Feng Zhou, Zhi Ping

    2015-04-15

    We present a method to fabricate a super-hydrophobic surface with a self-healing ability on an aluminium alloy substrate. The coatings are obtained by combining a two-step process (first, the substrate is immersed in a solution of HCl, HF and H{sub 2}O, and then in boiling water) and succeeding surface fluorination with a solution of poly(vinylidene-fluoride-co-hexafluoropropylene) and a fluoroalkyl silane. The morphological features and chemical composition were studied by scanning electron micrometry and energy-dispersive X-ray spectroscopy. The prepared super-hydrophobic aluminium surfaces showed hierarchical structures forming pores, petals and particles with a contact angle of 161° and a sliding angle of 3°.

  7. Properties of experimental copper-aluminium-nickel alloys for dental post-and-core applications

    PubMed Central

    Rittapai, Apiwat; Kajornchaiyakul, Julathep; Harniratisai, Choltacha

    2014-01-01

    PURPOSE This study aimed to develop a copper-aluminium-nickel alloy which has properties comparable to that of dental alloys used for dental post and core applications with the reasonable cost. MATERIALS AND METHODS Sixteen groups of experimental copper alloys with variants of 3, 6, 9, 12 wt% Al and 0, 2, 4, 6 wt% Ni were prepared and casted. Their properties were tested and evaluated. The data of thermal, physical, and mechanical properties were analyzed using the two-way ANOVA and Tukey's test (α=0.05). The alloy toxicity was evaluated according to the ISO standard. RESULTS The solidus and liquidus points of experimental alloys ranged from 1023℃ to 1113℃ and increased as the nickel content increased. The highest ultimate tensile strength (595.9 ± 14.2 MPa) was shown in the Cu-12Al-4Ni alloy. The tensile strength was increased as the both elements increased. Alloys with 3-6 wt% Al exhibited a small amount of 0.2% proof strength. Accordingly, the Cu-9Al-2Ni and Cu-9Al-4Ni alloys not only demonstrated an appropriate modulus of elasticity (113.9 ± 8.0 and 122.8 ± 11.3 GPa, respectively), but also had a value of 0.2% proof strength (190.8 ± 4.8 and 198.2 ± 3.4 MPa, respectively), which complied with the ISO standard requirement (>180 MPa). Alloys with the highest contents of nickel (6 wt% Ni) revealed a widespread decolourisation zone (5.0-5.9 mm), which correspondingly produced the largest cell response, equating positive control. CONCLUSION The copper alloys fused with 9 wt% Al and 2-4 wt% Ni can be considered for a potential use as dental post and core applications. PMID:25006386

  8. The flash-butt welding of aluminium alloys

    NASA Astrophysics Data System (ADS)

    Kuchuk-Iatsenko, S. I.; Cherednichok, V. T.; Semenov, L. A.

    Flash-butt welding (FBW) of high-strength aerospace Al alloys is conducted without gaseous-medium shielding and has undergone substantial development in the direction of automated operations. FBW yields virtually no pores, discontinuities, or cracks, and is therefore ideal for gas-impermeable joints. The dimensional accuracies achievable by FBW are a function of weld are inner stresses that are a full order of magnitude smaller than those of arc-welding methods. NDI methods can be incorporated into an automated FBW apparatus for direct inspection of welds.

  9. Further studies of the anodic dissolution in sodium chloride electrolyte of aluminium alloys containing tin and gallium

    NASA Astrophysics Data System (ADS)

    Nestoridi, Maria; Pletcher, Derek; Wharton, Julian A.; Wood, Robert J. K.

    As part of a programme to develop a high power density, Al/air battery with a NaCl brine electrolyte, the high rate dissolution of an aluminium alloy containing tin and gallium was investigated in a small volume cell. The objective was to define the factors that limit aluminium dissolution in condition that mimic a high power density battery. In a cell with a large ratio of aluminium alloy to electrolyte, over a range of current densities the extent of dissolution was limited to ∼1000 C cm -2 of anode surface by a thick layer of loosely bound, crystalline deposit on the Al alloy anode formed by precipitation from solution. This leads to a large increase in impedance and acts as a barrier to transport of ions.

  10. Effect of the nature of grain boundary regions on cavitation of a superplastically deformed aluminium alloy

    SciTech Connect

    Blandin, J.J.; Varloteaux, A.; Suery, M.; Hong, B.; L`Esperance, G.

    1996-06-01

    Superplastic deformation of aluminium alloys induces cavity formation throughout the material, so that superplastic forming usually requires to be carried out under superimposed gas pressure to minimize strain-induced damage. This paper deals with the beneficial effects of heat treatment at high temperature for several hours before deformation on cavitation behavior of a superplastically deformed 7475 alloy. Transmission electron microscopy observations show that several microstructural transformations are induced by superplastic deformation and affected by the heat treatment. At first, the generation of dispersoid free zones at the periphery of the grains is observed, the composition of which depends on the prior history of the specimen. Secondly, the formation of long thin fibers extending in the cavities in the as received specimens, these fibers being no longer present in the heat-treated conditions. A TEM characterization of the fibers is presented and a mechanism of their formation is discussed. Such a reduction of the cavitation level for a given strain is interesting in view of superplastic forming of aluminium alloys under atmospheric pressure.

  11. Microstructure refinement of commercial 7xxx aluminium alloys solidified by the electromagnetic vibration technique

    NASA Astrophysics Data System (ADS)

    Li, M.; Tamura, T.; Omura, N.; Murakami, Y.; Tada, S.

    2016-03-01

    This paper examines the microstructure refinement of commercial 7xxx aluminium alloys solidified by the electromagnetic vibration technique (EMV) as a function of vibration frequency, f. The microstructure evolution reveals that at the low frequency of f = 62.5 Hz, the solidified microstructure is coarse and with the increase of vibration frequency to f = 500 Hz, the grain size becomes the finest and further increase of frequency to f = 2000 Hz results in coarsening of microstructures. The refinement mechanism is clarified when considering the significant difference in electrical resistivities of the solid and the liquid in mushy zone, in which both phases coexist and subject to vibration. The frequency-dependent refinement behaviour is revealed when the displacement of the mobile solid and sluggish liquid is taken into account during solidification. In contrast to 3xxx aluminium alloys, no giant compounds have been discerned in the present 7xxx alloy regardless of the solidification condition. The formation of crystalline twin is briefly discussed when considering the vibration condition.

  12. Strength of the aluminium alloy 6082-T6 under high strain-rate conditions

    SciTech Connect

    Harrigan, J. J.; Millett, J. C. F.; Bourne, N. K.

    2007-12-12

    The measurement of shear strength via the use of lateral stress gauges has been shown to be a viable technique in a number of materials. An experimental investigation on the intermediate-rate behaviour and shock response of the aluminium alloy, 6082-T6, is reported here. Results obtained using the lateral stress gauge technique show that the shear strength increases with impact stress. The lateral stress behind the shock front is seen to be relatively flat, unlike many other face-centred cubic metals and alloys, where a decrease in lateral stress indicates an increase in shear strength. This unusal response may be a reflection of the high stacking fault energy of aluminium and its alloys resulting in a reduction of the work hardening (i.e. increases in dislocation and/or twin density). Further plate impact results show that the Hugoniot of 6082-T6 is in effect identical to that of the more widely known 6061-T6. Split Hopkinson pressure bar results are used to provide a fuller picture of the rate-dependant behaviour of 6082-T6 over a range of loading rates and conditions.

  13. Grain boundary segregation and hydrogen-induced fracture in 7050 aluminium alloy

    SciTech Connect

    Song, R.G.; Tseng, M.K.; Zhang, B.J.; Liu, J.; Jin, Z.H.; Shin, K.S.

    1996-08-01

    The relationships between grain boundary segregation and crack growth of stress corrosion and corrosion fatigue in 7050 aluminium alloy have been investigated under various aging conditions; the effects of grain boundary segregation on intergranular fracture work have been calculated using a quasichemical approach. The results show that the hydrogen content at the crack tip and the crack growth rate increase with the concentration of solid solution Mg on increasing grain boundary; both Mg and H segregation induce the intergranular fracture work to decrease. Mg segregation accelerates H enriching and crack propagation. It is indicated that a Mg-H interaction occurs in the processes of corrosion fatigue as well as stress corrosion.

  14. Influence of Process Parameters on the Quality of Aluminium Alloy EN AW 7075 Using Selective Laser Melting (SLM)

    NASA Astrophysics Data System (ADS)

    Kaufmann, N.; Imran, M.; Wischeropp, T. M.; Emmelmann, C.; Siddique, S.; Walther, F.

    Selective laser melting (SLM) is an additive manufacturing process, forming the desired geometry by selective layer fusion of powder material. Unlike conventional manufacturing processes, highly complex parts can be manufactured with high accuracy and little post processing. Currently, different steel, aluminium, titanium and nickel-based alloys have been successfully processed; however, high strength aluminium alloy EN AW 7075 has not been processed with satisfying quality. The main focus of the investigation is to develop the SLM process for the wide used aluminium alloy EN AW 7075. Before process development, the gas-atomized powder material was characterized in terms of statistical distribution: size and shape. A wide range of process parameters were selected to optimize the process in terms of optimum volume density. The investigations resulted in a relative density of over 99%. However, all laser-melted parts exhibit hot cracks which typically appear in aluminium alloy EN AW 7075 during the welding process. Furthermore the influence of processing parameters on the chemical composition of the selected alloy was determined.

  15. Preparation of aluminium-magnesium alloys and some valuable salts from used beverage cans.

    PubMed

    Rabah, Mahmoud A

    2003-01-01

    The purpose of this work is to recover standard aluminium-magnesium alloy(s) and some valuable salts from used beverage cans (UBCs). The suggested method updated the current recycling technology by augmenting removal of the coating paint, decreasing magnesium loss during melting process and improving hydrochloric acid leaching of the formed slag. Iron impurity present in the leaching solution, was removed by oxidation using oxygen gas or hydrogen peroxide and filtered as goethite. Results obtained revealed that a mixture of methyl ethyl ketone/dimethyl formamide entirely removes the paint coating at room temperature. The process compares favorably to the current methods involving firing or swell peeling. The coating decomposes to titanium dioxide by heating at 750 degrees C for 30 min. Standard compositions of Al-Mg alloys are formulated using secondary magnesium. The extent of recovery (R) of these alloy(s) is a function of the melting time and temperature and type of the flux. The maximum (R) value amounts to 94.4%. Sodium borate/chloride mix decreases magnesium loss to a minimum. The extent of leaching valuable salts from the slag increases with increasing the molarity, stoichiometric ratio and leaching temperature of the acid used. Removal of iron is a function of the potential of the oxidation process. Stannous chloride has been recovered from the recovered and dried salts by distillation at 700-750 degrees C.

  16. On the optimisation of machining parameters for dry drilling of aeronautic aluminium alloy

    NASA Astrophysics Data System (ADS)

    List, G.; Girot, F.

    2003-09-01

    Machining aluminium alloys without lubrication seriously increases the tool wear because of the severe tribological conditions at the tool/chip interface. Indeed, metal cutting generates high temperatures and pressures due to the high strain rate (ge104 s^{-1}) and the friction between the tool and the chip. Thus, it is very important to be able to clearly identify the parameters influencing the machining quality. In order to study dry drilling with W-Co carbide tools, experiments were conducted using different drill geometries and varying cutting conditions. The workpiece material used in this work is the aluminium alloy 2024 T-351. Optimise drill geometries can be deducted from experimental results to obtain holes with an aerospace quality. The following parameters were used to evaluate the holes quality : the minimum and maximum diameter deviations, the burr height and the surface roughness. The microscope observation of the tool rake face shows that the main damage is adhesion and diffusion wear revealing the presence of high temperature. Cutting conditions were tested and chosen to limit the tool damage and by consequence to increase the tool life.

  17. Finite volume modeling of laser assisted friction stir welding of 2017A-T451 aluminum alloy for enhanced sustainability of welded joints

    NASA Astrophysics Data System (ADS)

    Mimouni, Oussama; Badji, Riad; Hadji, Mohamed; Kouadri-Henni, Afia

    2016-10-01

    This study focuses on a new welding modification friction stir welding, using a preheating during the welding phase. This method utilizes laser energy to pre-heat the workpiece to a localized area at the front of the FSW tool, thereby reducing the temperature gradient over a localized area in advance of the tool. The amount of heat generated during welding determines the quality of the weld. Therefore the understanding of the temperature distribution is required to determine the optimal method of welding parameters. In this study, a two-dimensional model of an aluminum alloy plate coupled to a circular laser source is developed, using FLUENT software that is based on the finite volume method, also the geometry of the pin of the FSW tool was modified in several configurations to highlight the effect of the geometry of the tool on the temperature distribution in the welded plate. The model developed can be used to better understand the process, predict process performance and to determine the optimal parameters of the process.

  18. Effect of pulsed current GTA welding parameters on the fusion zone microstructure of AA 6061 aluminium alloy

    NASA Astrophysics Data System (ADS)

    Kumar, T. Senthil; Balasubramanian, V.; Babu, S.; Sanavullah, M. Y.

    2007-08-01

    AA6061 aluminium alloy (Al-Mg-Si alloy) has gathered wide acceptance in the fabrication of food processing equipment, chemical containers, passenger cars, road tankers, and railway transport systems. The preferred process for welding these aluminium alloys is frequently Gas Tungsten Arc (GTA) welding due to its comparatively easy applicability and lower cost. In the case of single pass GTA welding of thinner sections of this alloy, the pulsed current has been found beneficial due to its advantages over the conventional continuous current processes. The use of pulsed current parameters has been found to improve the mechanical properties of the welds compared to those of continuous current welds of this alloy due to grain refinement occurring in the fusion zone. In this investigation, an attempt has been made to develop a mathematical model to predict the fusion zone grain diameter incorporating pulsed current welding parameters. Statistical tools such as design of experiments, analysis of variance, and regression analysis are used to develop the mathematical model. The developed model can be effectively used to predict the fusion grain diameter at a 95% confidence level for the given pulsed current parameters. The effect of pulsed current GTA welding parameters on the fusion zone grain diameter of AA 6061 aluminium alloy welds is reported in this paper.

  19. Dual wavelength laser beam alloying of aluminium alloy for enhanced corrosion resistance

    SciTech Connect

    Liu, Z.; Watkins, K.G.; Steen, W.M.; Vilar, R.; Ferreira, M.G.

    1997-08-01

    Aluminum alloys are known for their poor resistance to localized attack and, in particular, for pitting in chloride-containing electrolytes. In this paper, improvement of the pitting corrosion resistance of 2014-T6 aluminum alloy has been investigated by means of laser surface alloying of Cr into the substrate. Since aluminum is highly reflective and thermally conductive material, it is often difficult to process with laser beams. Oxide films on the surface can prevent surface alloying as with the case of Cr alloying into aluminum by in-situ powder feeding. This work describes a new technique using mixed excimer laser and CO{sub 2} laser beam processing to generate a Cr alloyed layer on a 2014 aluminum alloy substrate. It is shown that improvement of alloying homogeneity following in-situ powder feeding can be achieved with mixed beam processing. Conditions under which this can be achieved have been studied and the effect of laser processing parameters on the surface roughness, oxidation and absorption is discussed. Microstructural and surface morphological analysis using optical microscopy, scanning electron microscopy and energy dispersive spectroscopy are also discussed. The electrochemical behavior of the treated samples in de-aerated 1 M NaCl solution has also been studied and has indicated that an improvement of pitting resistance by laser surface treatment can be achieved.

  20. Electrochemical characteristics of a carbon fibre composite and the associated galvanic effects with aluminium alloys

    NASA Astrophysics Data System (ADS)

    Liu, Z.; Curioni, M.; Jamshidi, P.; Walker, A.; Prengnell, P.; Thompson, G. E.; Skeldon, P.

    2014-09-01

    The electrochemical behaviour of a carbon fibre reinforced epoxy matrix composite in 3.5% NaCl and 3.5% NaCl + 0.5 M CuSO4 electrolytes was examined by potentiodynamic polarisation, potentiostatic polarisation and scanning electron microscopy. Exposed carbon fibres on two defined regions (“front” and “side”) are a focus of the investigation. The large size of the exposed carbon fibres on the side region is responsible for a higher cathodic current density than the front region in the NaCl electrolyte. The deposition of copper on the front surface of composite confirmed that the significantly higher cathodic current resulted from the exposure of the fibres to the NaCl electrolyte. Galvanic coupling between the composite and individual aluminium alloys (AA7075-T6 and AA1050) was used to measure galvanic potentials and galvanic current densities. The highly alloyed AA7075-T6 alloy and its high population density of cathodic sites compared to the AA1050 acted to reduce the galvanic effect when coupled to the composite front or side regions.

  1. Characterisation of the anodic layers formed on 2024 aluminium alloy, in tetraborate electrolyte containing molybdate ions

    NASA Astrophysics Data System (ADS)

    Moutarlier, V.; Pelletier, S.; Lallemand, F.; Gigandet, M. P.; Mekhalif, Z.

    2005-12-01

    Anodic layer growth on 2024 aluminium alloy at 70 °C, under 40 V, during 60 min, in 50 g L -1 di-sodium tetraborate solution containing di-sodium molybdate from 0.1 to 0.5 M (pH 10) is examined. Anodising behaviours strongly depend on additive concentration. Development of anodic films is favoured with weak molybdate additions (<0.3-0.4 M). The film thicknesses increase and the porosity of anodic layers decreases. Molybdenum (+VI), detected by X-ray photoelectron spectroscopy (XPS) analysis, is present in the anodic films and the Mo incorporation, studied by energy dispersive spectroscopy (EDS) analysis, increases with molybdate concentration. However, for high molybdate concentrations (>0.4 M), anodising behaviour becomes complex with the formation of a blue molybdenum oxide at the cathode. The growth of aluminium oxide is hindered. As the anodic layers are thinner, the Mo(+VI) incorporation significantly decreases. These two configurations implicate different corrosion performances in 5% sodium chloride solution at 35 °C. As the alkaline anodic layer formed with 0.3 M molybdate species is the thickest and the Mo incorporation is the more pronounced, its corrosion resistance is the highest. The effect of morphology and composition of anodic films on pitting corrosion is also discussed.

  2. Influence of rotary swaging and subsequent age hardening on properties of EN AW 6082 aluminium alloy

    NASA Astrophysics Data System (ADS)

    Maleček, L.; Palán, J.; Nacházel, J.; Dlouhý, J.

    2017-02-01

    Mechanical properties and microstructure of EN AW 6082 were investigated. The aluminium alloy was processed by combining the solution annealing, plastic deformation and artificial age hardening, respectively. The initial state of the investigated material was provided in the form of extruded rods with the diameter of 12 mm. For the solution annealing the temperature 530 °C was chosen. The plastic deformation was realized by rotary swaging at ambient temperature and the investigated material was rotary swaged from 12 to 10 mm in diameter. The effect of the age hardening temperature and time was studied at temperatures of 120 and 160 °C and times 1 - 12 hours. The impact of processing parameters on mechanical properties was assessed by tensile testing and hardness measurement. Metallographic examination was carried out by light optical microscopy (LOM) and scanning electron microscopy using electron backscatter diffraction (SEM-EBSD).

  3. Experimental characterisation and modelling of deformation- induced microstructure in an A6061 aluminium alloy

    NASA Astrophysics Data System (ADS)

    Kreyca, J. F.; Falahati, A.; Kozeschnik, E.

    2016-03-01

    For industry, the mechanical properties of a material in form of flow curves are essential input data for finite element simulations. Current practice is to obtain flow curves experimentally and to apply fitting procedures to obtain constitutive equations that describe the material response to external loading as a function of temperature and strain rate. Unfortunately, the experimental procedure for characterizing flow curves is complex and expensive, which is why the prediction of flow-curves by computer modelling becomes increasingly important. In the present work, we introduce a state parameter based model that is capable of predicting the flow curves of an A6061 aluminium alloy in different heat-treatment conditions. The model is implemented in the thermo-kinetic software package MatCalc and takes into account precipitation kinetics, subgrain formation, dynamic recovery by spontaneous annihilation and dislocation climb. To validate the simulation results, a series of compression tests is performed on the thermo-mechanical simulator Gleeble 1500.

  4. Strain rate effects on mechanical properties in tension of aluminium alloys used in armour applications

    NASA Astrophysics Data System (ADS)

    Cadoni, E.; Dotta, M.; Forni, D.; Bianchi, S.; Kaufmann, H.

    2012-08-01

    The mechanical properties in tension of two aluminium alloys (AA5059-H131 and AA7039-T651) used in armour applications were determined from tests carried out over a wide range of strain-rates on round specimens. The experimental research was developed in the DynaMat laboratory of the University of Applied Sciences of Southern Switzerland. The target strain rates were set at the following four levels: 10-3, 30, 300 and 1000s-1. The quasi-static tests were performed with a universal electromechanical machine, whereas a hydro-pneumatic machine and a Split Hopkinson Tensile Bar apparatus were used for medium and high strain-rates respectively. The required parameters by the Johnson-Cook constitutive law were also determined.

  5. The influence of uniaxial prestrain on biaxial r-values in 7075-O aluminium alloy

    NASA Astrophysics Data System (ADS)

    Anderson, N.; Brown, D.; McMurray, R. J.; Leacock, A. G.

    2011-05-01

    Biaxial test methods have been used to determine, not only yield behaviour under biaxial conditions, but also the strain response. This paper examines the influence of uniaxial prestrain upon the biaxial r-value by extending the disc compression test procedure proposed by Barlat et al. [1]. The extension involved the use of digital image measurements of in-plane strains. The material examined was a 7075-O condition aluminium alloy. The results of the experimental programme indicated that the biaxial r-value is unaffected by uniaxial prestrain. When using the disc compression test, the mode of deformation and therefore the biaxial r-value were found to be very sensitive to the prevailing friction conditions.

  6. The influence of uniaxial prestrain on biaxial r-values in 7075-O aluminium alloy

    SciTech Connect

    Anderson, N.; Brown, D.; McMurray, R. J.; Leacock, A. G.

    2011-05-04

    Biaxial test methods have been used to determine, not only yield behaviour under biaxial conditions, but also the strain response. This paper examines the influence of uniaxial prestrain upon the biaxial r-value by extending the disc compression test procedure proposed by Barlat et al. The extension involved the use of digital image measurements of in-plane strains. The material examined was a 7075-O condition aluminium alloy. The results of the experimental programme indicated that the biaxial r-value is unaffected by uniaxial prestrain. When using the disc compression test, the mode of deformation and therefore the biaxial r-value were found to be very sensitive to the prevailing friction conditions.

  7. Investigation of dynamic dry friction between stainless steel and aluminium alloy

    NASA Astrophysics Data System (ADS)

    Keightley, Peter; Winter, Ron; Stirk, Stewart

    2009-06-01

    Previous workers studied dynamic friction by using an impacting copper plate to drive a tapered aluminium alloy plug into a matching hole in a stainless steel outer sheath. The velocity of the back surface of the plug was measured using velocity interferometry. We have performed experiments on a version of this basic configuration that has been enlarged so that the sliding surfaces remain in contact for a longer time than with the original configuration. By comparing our results with computer simulations we conclude that the frictional forces between the inner cone and the steel outer are initially high but decrease significantly as the sliding proceeds. This effect is assumed to result from thermal softening of the material at the sliding interface. The study is supported by metallography of the recovered components.

  8. Optimization of process parameters in CNC turning of aluminium alloy using hybrid RSM cum TLBO approach

    NASA Astrophysics Data System (ADS)

    Rudrapati, R.; Sahoo, P.; Bandyopadhyay, A.

    2016-09-01

    The main aim of the present work is to analyse the significance of turning parameters on surface roughness in computer numerically controlled (CNC) turning operation while machining of aluminium alloy material. Spindle speed, feed rate and depth of cut have been considered as machining parameters. Experimental runs have been conducted as per Box-Behnken design method. After experimentation, surface roughness is measured by using stylus profile meter. Factor effects have been studied through analysis of variance. Mathematical modelling has been done by response surface methodology, to made relationships between the input parameters and output response. Finally, process optimization has been made by teaching learning based optimization (TLBO) algorithm. Predicted turning condition has been validated through confirmatory experiment.

  9. Microstructures in the 6060 aluminium alloy after various severe plastic deformation treatments

    SciTech Connect

    Adamczyk-Cieslak, Boguslawa Mizera, Jaroslaw; Kurzydlowski, Krzysztof Jan

    2011-03-15

    This paper presents the results concerning the microstructural refinement of the industrial 6060 aluminium alloy processed by severe plastic deformation (SPD). The high level of plastic deformation was achieved using the three methods: hydrostatic extrusion (HE), equal channel angular extrusion (ECAE) and extrusion torsion (ET), which differed in the dynamics of the loading, intensity and homogeneity of the plastic strain field. Microstructure analyses were performed before and after SPD deformation using a transmission (TEM) and a scanning electron microscope (SEM). The refined microstructures were examined qualitatively and quantitatively by the stereological methods and computer image analyses. The microstructure of the industrial 6060 aluminium alloy after deformation was characterized by an average grain size of about 0.4 {mu}m. The results show that the precipitates strongly affect the degree of refinement and the mechanism of microstructural transformations. During the SPD, the second phase particles break apart and homogenize. The HE method generates the largest increase of the volume fraction of the small primary particles. Moreover, the HE process is most effective in reducing the primary particle size. During HE and ECAE processes the second phase precipitates dissolve partially and change their shape. - Research Highlights: {yields} SPD results in a significant increase in the density of the small primary particles. {yields} SPD homogenizes the particle size distribution. {yields} HE and ECAE processes bring nano-grains in the vicinity of the primary particles. {yields} HE and ECAE processing results in the {beta}' precipitates partial dissolutions. {yields} During HE and ECAE processes the {beta}' particles change their shape.

  10. Flow and failure of an aluminium alloy from low to high temperature and strain rate

    NASA Astrophysics Data System (ADS)

    Sancho, Rafael; Cendón, David; Gálvez, Francisco

    2015-09-01

    The mechanical behaviour of an aluminium alloy is presented in this paper. The study has been carried out to analyse the flow and failure of the aluminium alloy 7075-T73. An experimental study has been planned performing tests of un-notched and notched tensile specimens at low strain rates using a servo-hydraulic machine. High strain rate tests have been carried out using the same geometry in a Hopkinson Split Tensile Bar. The dynamic experiments at low temperature were performed using a cryogenic chamber, and the high temperature ones with a furnace, both incorporated to the Hopkinson bar. Testing temperatures ranged from - 50 ∘C to 100 ∘C and the strain rates from 10-4 s-1 to 600 s-1. The material behaviour was modelled using the Modified Johnson-Cook model and simulated using LS-DYNA. The results show that the Voce type of strain hardening is the most accurate for this material, while the traditional Johnson-Cook is not enough accurate to reproduce the necking of un-notched specimens. The failure criterion was obtained by means of the numerical simulations using the analysis of the stress triaxiality versus the strain to failure. The diameters at the failure time were measured using the images taken with an image camera, and the strain to failure was computed for un-notched and notched specimens. The numerical simulations show that the analysis of the evolution of the stress triaxiality is crucial to achieve accurate results. A material model using the Modified Johnson-Cook for flow and failure is proposed.

  11. A survey of some metallographic etching reagents for restoration of obliterated engraved marks on aluminium-silicon alloy surfaces.

    PubMed

    Uli, Norjaidi; Kuppuswamy, R; Amran, Mohd Firdaus Che

    2011-05-20

    A brief survey to assess the sensitivity and efficacy of some common etching reagents for revealing obliterated engraved marks on Al-Si alloy surfaces is presented. Experimental observations have recommended use of alternate swabbing of 10% NaOH and 10% HNO(3) on the obliterated surfaces for obtaining the desired results. The NaOH etchant responsible for bringing back the original marks resulted in the deposition of some dark coating that has masked the recovered marks. The coating had been well removed by dissolving it in HNO(3) containing 10-20% acid. However, the above etching procedure was not effective on aluminium (99% purity) and Al-Zn-Mg-Cu alloy surfaces. Also the two reagents (i) immersion in 10% aq. phosphoric acid and (ii) alternate swabbing of 60% HCl and 40% NaOH suggested earlier for high strength Al-Zn-Mg-Cu alloys [23] were quite ineffective on Al-Si alloys. Thus different aluminium alloys needed different etching treatments for successfully restoring the obliterated marks. Al-Si alloys used in casting find wide applications especially in the manufacture of engine blocks of motor vehicles. Hence, the results presented in this paper are of much relevance in serial number restoration problems involving this alloy.

  12. Influences of post weld heat treatment on tensile properties of friction stir welded AA2519-T87 aluminium alloy joints

    NASA Astrophysics Data System (ADS)

    Sabari, S. Sree; Balasubramanian, V.; Malarvizhi, S.; Reddy, G. Madusudhan

    2015-12-01

    AA 2519-T87 is an aluminium alloy that principally contains Cu as an alloying element and is a new grade of Al-Cu alloy system. This material is a potential candidate for light combat military vehicles. Fusion welding of this alloy leads to hot cracking, porosity and alloy segregation in the weld metal region. Friction stir welding (FSW) is a solid state joining process which can overcome the above mentioned problems. However, the FSW of age hardenable aluminium alloys results in poor tensile properties in the as-welded condition (AW). Hence, post weld heat treatment (PWHT) is used to enhance deteriorated tensile properties of FSW joints. In this work, the effect of PWHT, namely artificial ageing (AA) and solution treatment (ST) followed by ageing (STA) on the microstructure, tensile properties and microhardness were systematically investigated. The microstructural features of the weld joints were characterised using an optical microscope (OM), scanning electron microscope (SEM) and transmission electron microscope (TEM). The tensile strength and microhardness of the joints were correlated with the grain size, precipitate size, shape and its distribution. From the investigation, it was found that STA treatment is beneficial in enhancing the tensile strength of the FSW joints of AA2519-T87 alloy and this is mainly due to the presence of fine and densely distributed precipitates in the stir zone.

  13. The influence of quench sensitivity on residual stresses in the aluminium alloys 7010 and 7075

    SciTech Connect

    Robinson, J.S.; Tanner, D.A.; Truman, C.E.; Paradowska, A.M.; Wimpory, R.C.

    2012-03-15

    The most critical stage in the heat treatment of high strength aluminium alloys is the rapid cooling necessary to form a supersaturated solid solution. A disadvantage of quenching is that the thermal gradients can be sufficient to cause inhomogeneous plastic deformation which in turn leads to the development of large residual stresses. Two 215 mm thick rectilinear forgings have been made from 7000 series alloys with widely different quench sensitivity to determine if solute loss in the form of precipitation during quenching can significantly affect residual stress magnitudes. The forgings were heat treated and immersion quenched using cold water to produce large magnitude residual stresses. The through thickness residual stresses were measured by neutron diffraction and incremental deep hole drilling. The distribution of residual stresses was found to be similar for both alloys varying from highly triaxial and tensile in the interior, to a state of biaxial compression in the surface. The 7010 forging exhibited larger tensile stresses in the interior. The microstructural variation from surface to centre for both forgings was determined using optical and transmission electron microscopy. These observations were used to confirm the origin of the hardness variation measured through the forging thickness. When the microstructural changes were accounted for in the through thickness lattice parameter, the residual stresses in the two forgings were found to be very similar. Solute loss in the 7075 forging appeared to have no significant effect on the residual stress magnitudes when compared to 7010. - Highlights: Black-Right-Pointing-Pointer Through thickness residual stress measurements made on large Al alloy forgings. Black-Right-Pointing-Pointer Residual stress characterised using neutron diffraction and deep hole drilling. Black-Right-Pointing-Pointer Biaxial compressive surface and triaxial subsurface residual stresses. Black-Right-Pointing-Pointer Quench sensitivity

  14. A microstructure-based yield stress and work-hardening model for textured 6xxx aluminium alloys

    NASA Astrophysics Data System (ADS)

    Khadyko, M.; Myhr, O. R.; Dumoulin, S.; Hopperstad, O. S.

    2016-04-01

    The plastic properties of an aluminium alloy are defined by its microstructure. The most important factors are the presence of alloying elements in the form of solid solution and precipitates of various sizes, and the crystallographic texture. A nanoscale model that predicts the work-hardening curves of 6xxx aluminium alloys was proposed by Myhr et al. The model predicts the solid solution concentration and the particle size distributions of different types of metastable precipitates from the chemical composition and thermal history of the alloy. The yield stress and the work hardening of the alloy are then determined from dislocation mechanics. The model was largely used for non-textured materials in previous studies. In this work, a crystal plasticity-based approach is proposed for the work hardening part of the nanoscale model, which allows including the influence of the crystallographic texture. The model is evaluated by comparison with experimental data from uniaxial tensile tests on two textured 6xxx alloys in five temper conditions.

  15. Pulsed laser cleaning of aluminium-magnesium alloys: effect of surface modifications on adhesion

    NASA Astrophysics Data System (ADS)

    Autric, Michel; Oltra, Roland

    2008-05-01

    Surface cleaning is a key step in many industrial processes and especially in laser surface treatments. During laser cleaning of metallic alloys using pulsed lasers, surface modification can be induced due to transient thermal effect. In ambient atmospheric conditions, an oxidation of the cleaned surface can be detected. The aim of this work was to characterize this transient oxidation that can occur below the laser energy domain leading to any phase change (melting, ablation) of the cleaned substrate. A Q-switched Nd:YAG laser (1.06 μm) with 10 ns pulse duration was used for this study. X-ray photoelectron spectroscopy and secondary ion mass spectroscopy were used for surface analysis of irradiated samples. Thermal oxidation took place on the aluminium-magnesium alloy (5000 series) during the irradiation in air (fluence range 0.6-1.4 Jcm-2). It has been demonstrated that this 10 ns laser thermal oxidation and the steady state thermal oxidation have the same mechanism. When the laser fluence reached 1 J cm -2 , the oxide formed by the thermal oxidation became in a large extent crystalline and its outer part was entirely covered by a continuous magnesium oxide layer.

  16. Effect of heat treatments on mechanical properties and damage evolution of thixoformed aluminium alloys

    SciTech Connect

    Cavaliere, P. . E-mail: pasquale.cavaliere@unile.it; Cerri, E.; Leo, P.

    2005-07-15

    In the present work, the effects of heat treatments on mechanical properties, microstructure evolution and damage resulting from plastic deformation of thixoformed A319 and A356 aluminium alloys, are studied. The thixoforming process can lead to the production of components that are characterized by very good mechanical properties and low porosity with a globular microstructure which is fine and uniform. The mechanical properties can be further improved through heat treatments such as T5 and T6. The prime factor influencing the damage in the alloys belonging to the Al-Si system is represented by decohesion of silicon particles resulting from the stress concentration at the particle-matrix interfaces. A statistical analysis of fractured particles after tensile tests in the as-cast and as-treated condition has been carried out in the present work; optical and scanning electron microscopy techniques have been used to characterize the microstructure and fracture surfaces of the specimens and the results are fully presented.

  17. Large area laser surface treatment of aluminium alloys for pitting corrosion protection

    NASA Astrophysics Data System (ADS)

    Chong, P. H.; Liu, Z.; Skeldon, P.; Thompson, G. E.

    2003-03-01

    Laser surface treatment has been recognised as a useful method for corrosion protection of surfaces as a result of improved microstructure/phase formation and compositions. In large area applications, overlapping of individual tracks corresponding to the width of the laser beam is often necessary. This involves re-melting and re-heating of a portion of the previous track and results in microstructural changes, such as precipitate coarsening and microsegregation, which may influence localised corrosion at the overlapped regions. The purpose of this work is to investigate the influence of overlapped regions on corrosion behaviour of laser-melted aluminium 2014-T6 alloy. Laser melting was carried out using a 3 kW CW Nd:YAG laser with a line beam profile. The microstructures of the central part and the overlapped region of the melt pool were examined using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). Pitting corrosion resistance was evaluated using potentiodynamic anodic polarisation in 1 M NaCl solution. The work revealed enhancement of the pitting potential by 170 mV compared with that of the untreated alloy, similar to that achieved by laser surface melting with a CO 2 laser in a Gaussian mode. The line beam profile results in elimination of the planar front zones at the treated surface, but this benefit was offset by a coarser microstructure.

  18. Simultaneous determination of lead, nickel, tin and copper in aluminium-base alloys using slurry sampling by electrical discharge and multielement ETAAS.

    PubMed

    Carrión, Nereida; Itriago, Ana M; Alvarez, Maria A; Eljuri, Elias

    2003-12-04

    The simultaneous multielement determination of Pb, Sn, Ni and Cu in aluminium alloys by electrothermal atomic absorption spectrometry (ETAAS) was performed by a quick method using slurry sampling. The metallic colloidal slurries were obtained by an electrical discharge operated in liquid medium. In this work, the effects of aluminium were evaluated and the results show that it causes a strong retention of Pb, Ni and Cu at low pyrolysis temperatures which is overcome by employing high pyrolysis temperatures. Aluminium also significantly improves the thermal stabilisation of Pb and Sn, it being possible to reach pyrolysis temperatures of 1100 and 1300 degrees C, respectively. Such stabilisation indicates that the performance of aluminium as a matrix modifier for Pb is better than that obtained using phosphate and magnesium nitrate without substantial changes of the figures of merit. The effects of aluminium on the atomisation characteristics of the elements and those coming from the simultaneous multielement determination on the figures of merit of the elements are also discussed. In this work, a calibration procedure involving a matrix matching method with aqueous aluminium standards is proposed as a simple and efficient way to solve the inconveniences originated by the aluminium matrix. The proposed method was applied to the simultaneous multielement determination of several aluminium-base alloy standards giving results well within the recommended values.

  19. Strain Measurement in Aluminium Alloy during the Solidification Process Using Embedded Fibre Bragg Gratings.

    PubMed

    Weraneck, Klaus; Heilmeier, Florian; Lindner, Markus; Graf, Moritz; Jakobi, Martin; Volk, Wolfram; Roths, Johannes; Koch, Alexander W

    2016-11-04

    In recent years, the observation of the behaviour of components during the production process and over their life cycle is of increasing importance. Structural health monitoring, for example of carbon composites, is state-of-the-art research. The usage of Fibre Bragg Gratings (FBGs) in this field is of major advantage. Another possible area of application is in foundries. The internal state of melts during the solidification process is of particular interest. By using embedded FBGs, temperature and stress can be monitored during the process. In this work, FBGs were embedded in aluminium alloys in order to observe the occurring strain. Two different FBG positions were chosen in the mould in order to compare its dependence. It was shown that FBGs can withstand the solidification process, although a compression in the range of one percent was measured, which is in agreement with the literature value. Furthermore, different lengths of the gratings were applied, and it was shown that shorter gratings result in more accurate measurements. The obtained results prove that FBGs are applicable as sensors for temperatures up to 740 °C.

  20. Spectroscopic study of plasma during electrolytic oxidation of magnesium-aluminium alloys

    NASA Astrophysics Data System (ADS)

    Jovović, J.

    2014-12-01

    Plasma during Electrolytic Oxidation (PEO) of magnesium-aluminium alloys is studied in this work by means of Optical Emission Spectroscopy (OES). Spectral line shapes of the Hβ, Al II 704.21 nm and Mg II 448.11 nm line are analyzed to measure plasma electron number density Ne. From the Hβ line profile, two PEO processes characterized by relatively low electron number densities Ne ≈ 1015 cm-3 and Ne ≈ 2 × 1016 cm-3 were discovered while the shape and shift of Al II and Mg II lines revealed the third process characterized by large electron density Ne = (1-2) × 1017 cm-3. Low Ne processes, related with breakdown in gas bubbles and on oxide surface, are not influenced by anode material or electrolyte composition. The ejection of evaporated anode material through oxide layer is designated here as third PEO process. Using the Boltzmann plot technique, electron temperature of 4000 K and 33000 K is determined from relative intensities of Mg I and O II lines, respectively. Several difficulties in the analysis of spectral line shapes are met during this study and the ways to overcome some of the obstacles are demonstrated.

  1. Strain Measurement in Aluminium Alloy during the Solidification Process Using Embedded Fibre Bragg Gratings

    PubMed Central

    Weraneck, Klaus; Heilmeier, Florian; Lindner, Markus; Graf, Moritz; Jakobi, Martin; Volk, Wolfram; Roths, Johannes; Koch, Alexander W.

    2016-01-01

    In recent years, the observation of the behaviour of components during the production process and over their life cycle is of increasing importance. Structural health monitoring, for example of carbon composites, is state-of-the-art research. The usage of Fibre Bragg Gratings (FBGs) in this field is of major advantage. Another possible area of application is in foundries. The internal state of melts during the solidification process is of particular interest. By using embedded FBGs, temperature and stress can be monitored during the process. In this work, FBGs were embedded in aluminium alloys in order to observe the occurring strain. Two different FBG positions were chosen in the mould in order to compare its dependence. It was shown that FBGs can withstand the solidification process, although a compression in the range of one percent was measured, which is in agreement with the literature value. Furthermore, different lengths of the gratings were applied, and it was shown that shorter gratings result in more accurate measurements. The obtained results prove that FBGs are applicable as sensors for temperatures up to 740 °C. PMID:27827900

  2. Constant and variable amplitude ultrasonic fatigue of 2024-T351 aluminium alloy at different load ratios.

    PubMed

    Mayer, H; Fitzka, M; Schuller, R

    2013-12-01

    Ultrasonic fatigue testing equipment is presented that is capable of performing constant amplitude (CA) and variable amplitude (VA) experiments at different constant load ratios. This equipment is used to study cyclic properties of aluminium alloy 2024-T351 in the high cycle fatigue (HCF) and very high cycle fatigue (VHCF) regime at load ratios R=-1 and R=0.5. CA loading does not reveal a fatigue limit below 10¹⁰ cycles. Cracks leading to VHCF failure start at broken constituent particles. Specimens that survived more than 10¹⁰ cycles at R=-1 contain non-propagating cracks of lengths below grain size. Resonance frequency and nonlinearity parameter β(rel) show changes of vibration properties of specimens at low fractions of their VHCF lifetime. VA lifetimes are measured in the HCF and VHCF regime and compared with Miner calculations. Damage sums decrease with decreasing load (and increasing mean lifetimes) and are lower for R=0.5 than R=-1.

  3. Deep surface rolling for fatigue life enhancement of laser clad aircraft aluminium alloy

    NASA Astrophysics Data System (ADS)

    Zhuang, W.; Liu, Q.; Djugum, R.; Sharp, P. K.; Paradowska, A.

    2014-11-01

    Deep surface rolling can introduce deep compressive residual stresses into the surface of aircraft metallic structure to extend its fatigue life. To develop cost-effective aircraft structural repair technologies such as laser cladding, deep surface rolling was considered as an advanced post-repair surface enhancement technology. In this study, aluminium alloy 7075-T651 specimens with a blend-out region were first repaired using laser cladding technology. The surface of the laser cladding region was then treated by deep surface rolling. Fatigue testing was subsequently conducted for the laser clad, deep surface rolled and post-heat treated laser clad specimens. It was found that deep surface rolling can significantly improve the fatigue life in comparison with the laser clad baseline repair. In addition, three dimensional residual stresses were measured using neutron diffraction techniques. The results demonstrate that beneficial compressive residual stresses induced by deep surface rolling can reach considerable depths (more than 1.0 mm) below the laser clad surface.

  4. In-vitro characterization of stress corrosion cracking of aluminium-free magnesium alloys for temporary bio-implant applications.

    PubMed

    Choudhary, Lokesh; Singh Raman, R K; Hofstetter, Joelle; Uggowitzer, Peter J

    2014-09-01

    The complex interaction between physiological stresses and corrosive human body fluid may cause premature failure of metallic biomaterials due to the phenomenon of stress corrosion cracking. In this study, the susceptibility to stress corrosion cracking of biodegradable and aluminium-free magnesium alloys ZX50, WZ21 and WE43 was investigated by slow strain rate tensile testing in a simulated human body fluid. Slow strain rate tensile testing results indicated that each alloy was susceptible to stress corrosion cracking, and this was confirmed by fractographic features of transgranular and/or intergranular cracking. However, the variation in alloy susceptibility to stress corrosion cracking is explained on the basis of their electrochemical and microstructural characteristics.

  5. Residual stresses in shape memory alloy fiber reinforced aluminium matrix composite

    NASA Astrophysics Data System (ADS)

    Tsz Loong, Tang; Jamian, Saifulnizan; Ismail, Al Emran; Nur, Nik Hisyammudin Muhd; Watanabe, Yoshimi

    2017-01-01

    Process-induced residual stress in shape memory alloy (SMA) fiber reinforced aluminum (Al) matrix composite was simulated by ANSYS APDL. The manufacturing process of the composite named as NiTi/Al is start with loading and unloading process of nickel titanium (NiTi) wire as SMA to generate a residual plastic strain. Then, this plastic deformed NiTi wire would be embedded into Al to become a composite. Lastly, the composite is heated form 289 K to 363 K and then cooled back to 300 K. Residual stress is generated in composite because of shape memory effect of NiTi and mismatch of thermal coefficient between NiTi wire and Al matrix of composite. ANSYS APDL has been used to simulate the distribution of residual stress and strain in this process. A sensitivity test has been done to determine the optimum number of nodes and elements used. Hence, the number of nodes and elements used are 15680 and 13680, respectively. Furthermore, the distribution of residual stress and strain of nickel fiber reinforced aluminium matrix composite (Ni/Al) and titanium fiber reinforced aluminium matrix composite (Ti/Al) under same simulation process also has been simulated by ANSYS APDL as comparison to NiTi/Al. The simulation results show that compressive residual stress is generated on Al matrix of Ni/Al, Ti/Al and NiTi/Al during heating and cooling process. Besides that, they also have similar trend of residual stress distribution but difference in term of value. For Ni/Al and Ti/Al, they are 0.4% difference on their maximum compressive residual stress at 363K. At same circumstance, NiTi/Al has higher residual stress value which is about 425% higher than Ni/Al and Ti/Al composite. This implies that shape memory effect of NiTi fiber reinforced in composite able to generated higher compressive residual stress in Al matrix, hence able to enhance tensile property of the composite.

  6. Influence of ECAP on Densification Behaviour in the PM Aluminium Al-Mg-Si-Cu-Fe Alloy

    NASA Astrophysics Data System (ADS)

    Bidulská, Jana; Kvačkaj, Tibor; Kočiško, Róbert; Bidulský, Róbert; Grande, Marco Actis

    2010-09-01

    The main aim of this paper is to show how ECAP influences the densification behaviour of PM aluminium alloys. An aluminium based powder (Al-Mg-Si-Cu-Fe) was used as material to be investigated. After applying different compacting pressures, specimens were dewaxed in a ventilated furnace at 400 °C for 60 min. Sintering was carried out in a vacuum furnace at 610 °C for 30 min. The specimens were ECAPed for 1 pass. Optical characterization was carried out on the minimum of 10 different image fields. The results were measured for each pore individually in order to describe the dimensional and morphological porosity characteristics. ECAP influences the porosity distribution in terms of the severe shear deformation involved.

  7. Laser surface melting of aluminium alloy 6013 for improving stress corrosion and corrosion fatigue resistance

    NASA Astrophysics Data System (ADS)

    Xu, Wen-Long

    Laser surface treatment of aluminium alloy 6013, a relatively new high strength aluminium alloy, was conducted with the aim of improving the alloy's resistance to stress corrosion cracking and corrosion fatigue. In the first phase of this research, laser surface melting (LSM) of the alloy was conducted using an excimer laser. The microstructural changes induced by the laser treatment were studied in detail and characterised. The results showed that excimer LSM produced a relatively thin, non-dentritic planar re-melted layer which is largely free of coarse constituent particles and precipitates. The planar growth phenomenon was explained using the high velocity and high temperature gradient absolute stability criteria. The structure of the oxide and/or the nitride bearing film at the outmost surface of the re-melted layer was also characterised. The results of the electrochemical tests showed that the pitting corrosion resistance of the alloy could be greatly increased by excimer laser melting, especially when the alloy was treated in nitrogen gas: the corrosion current density of the N2-treated specimen was some two orders of magnitude lower than that of the air-treated specimen which was one order of magnitude lower than that of the untreated specimen. The effect of the outer surface oxide and/or nitride bearing film per se on pitting corrosion resistance was determined. The results of a Mott - Schottky analysis strongly suggest that the outer surface film, which exhibited the nature of an n-type semiconductor was responsible for the significant improvement of the corrosion resistance of the laser-treated material. Furthermore, the corrosion response of the surface film was modelled using equivalent circuits. Based on the results of the slow strain rate tensile (SSRT) and corrosion fatigue tests, the stress corrosion cracking and pitting corrosion fatigue behaviour of the excimer laser treated material was evaluated. The results of the SSRT test showed that, in

  8. Determination of aluminium in iron, steel and ferrous and non-ferrous alloys by atomic-absorption spectrophotometry after a mercury-cathode separation and extraction of the aluminium-acetylacetone complex.

    PubMed

    Donaldson, E M

    1981-07-01

    A method for determining 0.0005% or more of total aluminium in high- and low-alloy steels, iron and ferrovanadium is described. Iron, chromium and other matrix elements are separated from aluminium by electrolysis with a mercury cathode and aluminium is separated from tungsten, titanium, vanadium and phosphate by chloroform extraction of its acetylacetone complex at pH 6.5 from an ammonium acetate-hydrogen peroxide medium. The extract is evaporated to dryness and organic material is destroyed with nitric and perchloric acids. Aluminium is determined by atomic-absorption spectrophotometry in a nitrous oxide-acetylene flame, at 309.3 nm, in a 5% v/v perchloric acid medium containing 1000 mug of sodium per ml. Acid-soluble and acid-insoluble aluminium can also be determined. The method is also applicable to copper- and nickel-base alloys. Results obtained by this method are compared with those obtained spectrophotometrically with Pyrocatechol Violet, after the separations described above followed by the separation of the residual co-extracted iron and copper by a combined ammonium pyrrolidinedithiocarbamate-cupferron-chloroform extraction from 10% v/v hydrochloric acid medium.

  9. Electromagnetic Gauge Study of Laser-Induced Shock Waves in Aluminium Alloys

    NASA Astrophysics Data System (ADS)

    Peyre, P.; Fabbro, R.

    1995-12-01

    The laser-shock behaviour of three industrial aluminum alloys has been analyzed with an Electromagnetic Gauge Method (EMV) for measuring the velocity of the back free surface of thin foils submitted to plane laser irradiation. Surface pressure, shock decay in depth and Hugoniot Elastic Limits (HEL) of the materials were investigated with increasing thicknesses of foils to be shocked. First, surface peak pressures values as a function of laser power density gave a good agreement with conventional piezoelectric quartz measurements. Therefore, comparison of experimental results with computer simulations, using a 1D hydrodynamic Lagrangian finite difference code, were also in good accordance. Lastly, HEL values were compared with static and dynamic compressive tests in order to estimate the effects of a very large range of strain rates (10^{-3} s^{-1} to 10^6 s^{-1}) on the mechanical properties of the alloys. Cet article fait la synthèse d'une étude récente sur la caractérisation du comportement sous choc-laser de trois alliages d'aluminium largement utilisés dans l'industrie à travers la méthode dite de la jauge électromagnétique. Cette méthode permet de mesurer les vitesses matérielles induites en face arrière de plaques d'épaisseurs variables par un impact laser. La mise en vitesse de plaques nous a permis, premièrement, de vérifier la validité des pressions d'impact superficielles obtenues en les comparant avec des résultats antérieurs obtenus par des mesures sur capteurs quartz. Sur des plaques d'épaisseurs croissantes, nous avons caractérisé l'atténuation des ondes de choc en profondeur dans les alliages étudiés et mesuré les limites d'élasticité sous choc (pressions d'Hugoniot) des alliages. Les résultats ont été comparés avec succès à des simulations numériques grâce à un code de calcul monodimensionnel Lagrangien. Enfin, les valeurs des pressions d'Hugoniot mesurées ont permis de tracer l'évolution des contraintes d

  10. Experimental and numerical investigation of the residual yield strength of aluminium alloy EN AW-2024-T3 affected by artificially produced pitting corrosion

    NASA Astrophysics Data System (ADS)

    Pippig, R.; Schmidl, E.; Steinert, P.; Schubert, A.; Lampke, T.

    2017-03-01

    In this study, the behaviour of the residual yield strength of aluminium alloy EN AW-2024-T3 affected by the morphology and numbers of corrosion pits (defects) is presented. Since specific defect structures are not reproducible during experimental corrosion tests, metal sheets with different numbers of pits and pit shapes are produced using laser micro structuring. The defect structures are measured using laser scanning microscopy. To compare the stress states of the micro structured and real corroded metal sheets, FE-analysis is used. Afterwards, uniaxial tensile tests are carried out and critical defect parameters in terms of yield strength reduction of the investigated aluminium alloy are detected.

  11. Contribution on Taguchi's Method Application on the Surface Roughness Analysis in End Milling Process on 7136 Aluminium Alloy

    NASA Astrophysics Data System (ADS)

    ȚÎȚU, M. A.; POP, A. B.

    2016-11-01

    The resulting surface quality after the cutting process is one of the most important characteristics of product quality and also the most frequent customer requirement. Previous research was focused on the effect investigation of machining parameters: cutting speed [1] and feed per tooth [2] on surface roughness. This paper is in itself a continuation of a previous research [3], in which, with Taguchi's method it was determined the level of influence of the cutting parameters on surface roughness of 7136 aluminium alloy in end milling process. The purpose of this paper is to highlight the importance of Taguchi's method use to analyse the surface roughness of 7136 aluminium alloy in end milling process. To conduct the experiments, three cutting parameters were used: cutting speed, feed per tooth and cutting depth. To analyse the surface quality, the surface roughness Ra (the arithmetic average of the absolute values) was measured. It was determined the recommended configuration regarding the optimum values of each machining parameter and the interactions between them, in order to obtain the better cutting process performance and to reduce the surface roughness sensitivity to uncontrollable factors. Based on a full factorial experiment were confirmed the obtained results by applying the Taguchi's method. Final results are a starting point for further research.

  12. The strain rate sensitivity and constitutive equations including damage for the superplastic behaviour of 7xxx aluminium alloys

    NASA Astrophysics Data System (ADS)

    Yang, Jian; Boude, Serge; Giraud, Eliane; Dal Santo, Philippe

    2013-05-01

    Superplasticity is a characteristic of certain materials, in particular aluminium alloys, whereby very large deformations (up to 1000 %) can be obtained before fracture under certain conditions. Superplastic forming is therefore the process of deforming a flange under these conditions by applying a variable pressure. The final geometry is obtained when the flange takes the form of a die. In order to deform a material superplastically, the temperature of the material should be approximately a half of the absolute melting point of the material and the strain rate (or flow stress) should remain within a certain range. The most important issues concerning the industrial process are the prediction of the final thickness distribution and the computation of the optimal pressure law to maintain superplastic conditions. Finite element simulations make these predictions possible for industrial components. To ensure the precision of the simulations, it is important to have good knowledge of the material behaviour in the superplastic domain: rheological parameters, grain size, damage law, etc. This paper presents an experimental analysis of the superplastic behaviour of a 7xxx aluminium alloy used for aeronautic applications. The parameters of the constitutive equations (including damage) are identified by using tensile tests, spherical bulging tests and numerical simulations [1, 2]. The performance of the proposed laws [1, 3, and 4] is tested using axisymmetrical geometries with complex shapes by the comparison of numerical simulations and bulge tests.

  13. Analysis Of The Surface Roughness Obtained During The Dry Turning Of UNS A97050-T7 Aluminium Alloys

    NASA Astrophysics Data System (ADS)

    de Agustina, B.; Rubio, E. M.; Villeta, M.; Sebastián, M. A.

    2009-11-01

    Currently, in the aeronautical, aerospace and automotive industries there is high demand of materials such as the aluminium alloys that have high resistance even at high temperatures as well as a low density. For this reason, these alloys are widely used for the production of different elements that compose aircraft and aerospace vehicles. Nevertheless, in spite of the important role these materials have from the competitive point of view, they can commonly show problems of machinability associated with the tool wear. That has made that traditionally cutting fluids had been used in machining processes. However, they can contain environmentally harmful constituents and increase considerably the total cost of the process. Therefore, researches have been focused on the development of cleaner production technologies applications as dry machining. This leads to the search for combinations of cutting parameters and type of tools (types of coatings and different geometries) that could improve the machining under such conditions. The aim of this study is to analyse the relationship between the surface roughness obtained during the dry turning of aluminium UNS A97050-T7 bars and the cutting parameters (cutting speed and feed) using three different tools. As a first conclusion it could be affirmed that the feed was the cutting parameter more influential on the surface roughness and to a lesser extend the cutting speed, the type of tool and the interaction between the type of tool and the feed.

  14. Study of twin-roll cast Aluminium alloys subjected to severe plastic deformation by equal channel angular pressing

    NASA Astrophysics Data System (ADS)

    Poková, M.; Cieslar, M.

    2014-08-01

    Aluminium alloys prepared by twin-roll casting method become widely used in industry applications. Their high solid solution supersaturation and finer grains ensure better mechanical properties when compared with the direct-chill cast ones. One of the possibilities how to enhance their thermal stability is the addition of zirconium. After heat treatment Al3Zr precipitates form and these pin moving grain boundaries when the material is exposed to higher temperatures. In the present work twin-roll cast aluminium alloys based on AA3003 with and without Zr addition were annealed for 8 hours at 450 °C to enable precipitation of Al3Zr phase. Afterwards they were subjected to severe plastic deformation by equal channel angular pressing, which led to the reduction of average grain size under 1 μm. During subsequent isochronal annealing recovery and recrystallization took place. These processes were monitored by microhardness measurements, light optical microscopy and in-situ transmission electron microscopy. The addition of Zr stabilizes the grain size and increases the recrystallization temperature by 100 °C.

  15. Small Crack Growth and Fatigue Life Predictions for High-Strength Aluminium Alloys. Part 1; Experimental and Fracture Mechanics Analysis

    NASA Technical Reports Server (NTRS)

    Wu, X. R.; Newman, J. C.; Zhao, W.; Swain, M. H.; Ding, C. F.; Phillips, E. P.

    1998-01-01

    The small crack effect was investigated in two high-strength aluminium alloys: 7075-T6 bare and LC9cs clad alloy. Both experimental and analytical investigations were conducted to study crack initiation and growth of small cracks. In the experimental program, fatigue tests, small crack and large crack tests A,ere conducted under constant amplitude and Mini-TWIST spectrum loading conditions. A pronounced small crack effect was observed in both materials, especially for the negative stress ratios. For all loading conditions, most of the fatigue life of the SENT specimens was shown to be crack propagation from initial material defects or from the cladding layer. In the analysis program, three-dimensional finite element and A weight function methods were used to determine stress intensity factors and to develop SIF equations for surface and corner cracks at the notch in the SENT specimens. A plastisity-induced crack-closure model was used to correlate small and large crack data, and to make fatigue life predictions, Predicted crack-growth rates and fatigue lives agreed well with experiments. A total fatigue life prediction method for the aluminum alloys was developed and demonstrated using the crack-closure model.

  16. Formulation of anisotropic Hill criteria for the description of an aluminium alloy behaviour during the channel die compression test

    SciTech Connect

    Gavrus, A.; Francillette, H.

    2007-04-07

    During the last years the study of the plastic deformation modes and the anisotropic mechanical behaviour of aluminium alloys have been the subject of many investigations. This paper deals with a phenomenological identification of an anisotropic Hill constitutive equation of aluminium AU4G samples using a channel die compression device at room temperature. By considering the different possible orientations of the samples in the channel die device, three initial textures, named ND (normal direction Z), LD (longitudinal direction X) and TD (transverse direction Y), were defined with the corresponding stresses {sigma}ND, {sigma}LD and {sigma}TD. To describe the anisotropy of the material, a quadratic Hill criteria is used. An Avrami type equation based on the mixture of the hardening and softening phenomena is used to describe variation of each stress component with the equivalent plastic strain. The identification of the parameters of the law is made using an identification software (OPTPAR) and a good correlation between the experimental stresses and computed ones is obtained. The variation of the Hill parameters with a proposed equivalent strain, describing the deformation history of the material, is analysed. Finally, using the expressions of F, G, H and N, the constitutive equation of the normal anisotropy in the plane XY is obtained.

  17. Application of Minkowski layer for intergranular fractal surfaces of multiphase active microalloyed and alloyed aluminium-silicate ceramics

    NASA Astrophysics Data System (ADS)

    Purenović, J. M.; Randjelović, M. S.; Matović, B. Z.; Purenović, M. M.

    2015-03-01

    Microalloyed and alloyed aluminium-silicate ceramics represents multiphase and multifunctional solid-solid system. The microstructure of aluminium-silicate ceramics matrix is arranged with favorable relationship between crystallinity and amorphousness. Numbered physical processes and interactions take place in very complex intergranular and interphase areas, making new boundaries and regions with fractal nature. Fractal nature of grains contours, macro, mezzo and micro pores and nanostructure phases at grain boundaries make this ceramics an active dielectric material. The synergistic effect of additives, dislocations and impurities leads to dislocations movement at grain boundaries and fragmentation of existing grains in a large number of micrograins with distinct fractal nature. Hence, permanent change of micromorphology occurs in intergranular area. Fractal analysis of intergranular microstructure has included application of Minkowski layer, correlated with fractal dimension. It represents convex layer of grains contour roughness and irregularity, determined in accordance with grain contours fractality. The introduction of fractal microstructure analysis allows better interpretation of many physical and physico-chemical processes, bearing in mind that Minkowski layer defines grains contact probability.

  18. Effect of friction stir processing on the fatigue properties of a Zr-modified 2014 aluminium alloy

    SciTech Connect

    Cavaliere, P. . E-mail: pasquale.cavaliere@unile.it

    2006-08-15

    The fatigue properties of a Zr-modified 2014 aluminium alloy resulting from friction stir processing (FSP) were analysed in the present study. The sheets were processed parallel to the extrusion direction; the tensile mechanical properties were evaluated at room temperature in the longitudinal direction with respect to the processing one in order to observe the differences from the parent material as a function of the strong grain refinement due to the friction stir process. The fatigue endurance (S-N) curve of the FSP material was obtained by using a resonant electro-mechanical testing machine under constant loading control up to 250 Hz with sine wave loading. The cyclic fatigue tests were conducted in the axial total stress-amplitude control mode with R = {sigma} {sub min}/{sigma} {sub max} = 0.1. The microstructure resulting from the FSW process was studied by employing optical and scanning electron microscopy.

  19. Aging effects of diamond reinforced aluminium alloys submitted to deep space real conditions. Structural, chemical and electrical degradation

    NASA Astrophysics Data System (ADS)

    Korneli, Grigorov; Bouzekova-Penkova, Anna; Datcheva, Maria; Avdeev, George; Grushin, Valerii; Klimov, Stanislav

    2016-07-01

    An aluminium alloy (Al-Cu-Zn-Mg) reinforced with ultra-dispersed diamond powder and tungsten (W), has been prepared in form of 7 cm bars and 4 mm diameter. One part of them stayed 2 years on satellite exposed to outer space, where the Sun activity and the background radiation were monitored. After satellite return both batches has been studied. Structural test, mainly micro-hardness together with detailed X-rays analyses was performed. The satellite makes a tour around the Earth each two hours, the temperature difference being circa 300oC. The micro-hardness being measured with Agilent G200 nano-indentor shows a significant drop of 25%. The XRD patterns are consistent with the previous results, states defects incorporation, and crystalline cells deterioration.

  20. Regarding to the Variance Analysis of Regression Equation of the Surface Roughness obtained by End Milling process of 7136 Aluminium Alloy

    NASA Astrophysics Data System (ADS)

    POP, A. B.; ȚÎȚU, M. A.

    2016-11-01

    In the metal cutting process, surface quality is intrinsically related to the cutting parameters and to the cutting tool geometry. At the same time, metal cutting processes are closely related to the machining costs. The purpose of this paper is to reduce manufacturing costs and processing time. A study was made, based on the mathematical modelling of the average of the absolute value deviation (Ra) resulting from the end milling process on 7136 aluminium alloy, depending on cutting process parameters. The novel element brought by this paper is the 7136 aluminium alloy type, chosen to conduct the experiments, which is a material developed and patented by Universal Alloy Corporation. This aluminium alloy is used in the aircraft industry to make parts from extruded profiles, and it has not been studied for the proposed research direction. Based on this research, a mathematical model of surface roughness Ra was established according to the cutting parameters studied in a set experimental field. A regression analysis was performed, which identified the quantitative relationships between cutting parameters and the surface roughness. Using the variance analysis ANOVA, the degree of confidence for the achieved results by the regression equation was determined, and the suitability of this equation at every point of the experimental field.

  1. The aluminium-scandium-lithium-magnesium system as a potential source of superplastically formable alloys

    SciTech Connect

    Emigh, R.A.

    1990-07-01

    Alloys from the aluminum-lithium-scandium-magnesium system have been cast and rolled for study. The goal is to evaluate this system for the development of superplastically formable, high strength alloys. Aluminum-scandium-magnesium alloys have shown potential as superplastic alloys. These alloys rely on small Al{sub 3}Sc (ordered L1{sub 2}) precipitates for grain structure stabilization and strengthening. Additional precipitation strengthening is required to raise their strength to levels sufficient for aircraft applications. The addition of lithium provides this additional strengthening through the formation of Al{sub 3}Li({delta}{prime}). To produce the alloys studied in this research, a unique induction melting furnace was constructed that incorporates special features to produce aluminum-lithium alloys with low hydrogen content. The furnace also features a water cooled, copper casting mold to achieve a moderately rapid solidification rate. This is because the amount of scandium used (0.5 wt %) is in excess of the solubility limit and Al{sub 3}Sc cannot be re-solutionized to any extent. It is therefore desired to super-saturate the matrix with as much scandium as possible for later precipitation. Two high lithium alloys were produced, ALS2 (nominal composition Al-2.2Li-O.5 Sc) and AlS4 (nominal composition Al-2.0Li-2.2Mg-0.5Sc) that were strengthened with {delta}{prime} (Al{sub 3}Li). These alloys exhibited strength and ductility superior to those of aluminum-lithium-(magnesium)-zirconium alloys. This is because the scandium containing alloys have developed a finer grain structure and the Al{sub 3}Sc precipitates contribute to the alloys strength. 41 refs., 29 figs.

  2. Hydrogen generation by the hydrolysis reaction of ball-milled aluminium-lithium alloys

    NASA Astrophysics Data System (ADS)

    Chen, Xingyu; Zhao, Zhongwei; Liu, Xuheng; Hao, Mingming; Chen, Ailiang; Tang, Zhongyang

    2014-05-01

    The addition of Li can prevent an inert alumina film from forming on the surface of Al alloy particles, allowing the rapid hydrogen generation of Al alloys to be achieved. However, because the Li content is less than 10%, the hydrogen generation rate and hydrogen yield of Al-Li alloys are significantly decreased. In this work, NaCl is introduced to prepare Al-Li alloys with low Li contents by ball milling. The research results show that by increasing the amount of NaCl added, the ball milling time and Li content can effectively improve the hydrogen generation of the alloys. Under optimal preparation conditions, the ultimate hydrogen yield of Al-Li alloys can reach 100%. The initial water temperature has almost no effect on the generation of hydrogen, even at 0 °C. Ca2+ and Mg2+ can combine with OH- to form the insoluble compounds Ca(OH)2 and Mg(OH)2, which can prevent hydrogen generation. NO3- reacts with Al to form ammonia and reduce the hydrogen yield of the alloys. Therefore, Al-Li alloys should be prevented from reacting with water containing Ca2+, Mg2+ and NO3-. Al-Li alloys must be stored in isolation from air to maintain good hydrogen-generation performances.

  3. 7 CFR 201.7a - Treated seed.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Treated seed. 201.7a Section 201.7a Agriculture..., Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) FEDERAL SEED ACT FEDERAL SEED ACT REGULATIONS Records for Agricultural and Vegetable Seeds § 201.7a Treated seed. The complete record for...

  4. Comparative Investigation on Modal analysis of LM25 Aluminium alloy with other Aluminim alloys using Finite element analysis software

    NASA Astrophysics Data System (ADS)

    Arunkumar, S.; Baskaralal, V. P. M.; Muthuraman, V.

    2017-03-01

    The rudimentary steps of the modal analysis and simulation are carried out. The modal analysis is carried out on the different Aluminum Alloys cantilever beam. The cantilever beam is designed in the graphical environment of the ANSYS. The cantilever beam was fine-tuned on one end with all degree of liberation on this end were taken, beam cannot move and rotate. Mode shapes and natural frequencies are premeditated in platforms ANSYS with arithmetical formulation of the direct solver including the block Lanczos method. Aluminum alloys are widely utilized in much application due to their estimable weight to vigor property. Many examination works have been distributed out to make developments the mechanical properties of aluminum alloys. The composition of alloying elements plays a consequential role in deciding the properties of an alloy. In this study a numerical analysis implement i.e., finite element analysis (FEA) is utilized. The work obtainable in this paper is aimed at the study of effect of modal analysis of different aluminum alloys. The modeling and analysis is carried out utilizing ANSYS FEA software. A modal analysis is carried out to understand the modes of frequency demeanor of the material considered. The modal analysis play a vital role in the design of components subjected to high vibration.

  5. Grain Boundary Sliding in Ultra-fine Grained 5083 Aluminium Alloy

    NASA Astrophysics Data System (ADS)

    Sung, Ming-Je

    Quantitative measurement and analysis of grain boundary sliding in Ultra-fine grained 5083 Aluminium by AFM was conducted at 623K. The grain size of as received cryomilled Ultra-fine Grained Aluminium was characterized by AFM and TEM, and the average was founded to be about 300nm. Ion beam polishing / etching technology was used to reveal grain boundaries for AFM characterization. The vertical offset of grain boundary sliding was measured by comparing pre-defoemation and post-deformation AFM images. By analyzing these measurements, the contribution of grain boundary sliding to the total strain was estimated as 22% - 52% at a strain rate of 10 -4 /sec -5x10-2/sec. It was demonstrated that the relatively low value of the contribution of grain boundary sliding to the total strain is most likely the result of testing under experimental condition that favor the dominance of region I ( low stress) of the sigmoidal behavior characterizing high strain rate superplasticity, which was previously reported.

  6. Synergism between cerium nitrate and sodium dodecylbenzenesulfonate on corrosion of AA5052 aluminium alloy in 3 wt.% NaCl solution

    NASA Astrophysics Data System (ADS)

    Liu, Jie; Wang, Dapeng; Gao, Lixin; Zhang, Daquan

    2016-12-01

    The synergistic inhibition effect of rare earth cerium nitrate and sodium dodecylbenzenesulfonate (DBS) on corrosion of AA5052 aluminium alloy in 3 wt.% NaCl solution was investigated by electrochemical impedance spectroscopy (EIS), potentiodynamic polarization curve, scanning electron microscope (SEM) and Fourier transform infrared spectroscopy (FT-IR). The results show that the single cerium nitrate or DBS has a limited inhibition effect against corrosion of AA5052 alloy. The combination cerium ions with DBS produced strong synergistic effect on corrosion inhibition for AA5052 alloy and rendered a negaitve shift of the corrosion potential. The formation of the complex of Al(DBS)3 and Ce(DBS)3 stabilized the passive film of Al2O3 and CeO2, retarding both the cathodic and anodic processes of AA5052 alloy corrosion reaction significantly.

  7. Effect of thermal exposure on mechanical properties hypo eutectic aerospace grade aluminium-silicon alloy

    NASA Astrophysics Data System (ADS)

    Nagesh Kumar, R.; Ram Prabhu, T.; Siddaraju, C.

    2016-09-01

    The effect of thermal exposure on the mechanical properties of a C355.0 aerospace grade aluminum-silicon alloy (5% Si - 1.2% Cu - 0.5% Mg) was investigated in the present study. The alloy specimens were subjected to T6 (solution treatment and artificial ageing treatment) temper treatment to enhance the strength properties through precipitation hardening. The T6 temper treatment involved solution heat treatment at 520oC for 6h, followed by water quenching and ageing at 150oC. After the heat treatment, the specimens were exposed to various temperatures (50oC, 100oC, 150oC, 200oC and 250oC) for 5 and 10 h to study the structural applications of this alloy to the various Mach number military aircrafts. After the thermal exposure, specimens were tested for tensile, hardness and impact properties (Charpy). The microstructure of the thermal exposed specimens was examined in the optical microscopes and correlated with the mechanical properties results. In summary, an increase of exposure time has a different effect on the tensile and hardness properties of the alloy. For the exposure time 5h, the tensile and hardness properties increase upto 100oC and later decrease with an increase of temperature. In contrast, the tensile and hardness properties linearly decrease with an increase of temperature. Several factors such as matrix grain growth, diffusion rate, Si particles size and distribution, precipitate stability play a key role on deciding the tensile properties of the alloy. Comparing the relative effects of temperature and time, the temperature effects dominate more in deteriorating tensile properties of the alloy. There are no effects of exposure temperature and/or time on the impact properties of the alloy.

  8. Laser-induced electrochemical de- and repassivation investigations on plasma-oxidized aluminium alloys

    NASA Astrophysics Data System (ADS)

    Nagy, Tristan O.; Pacher, Ulrich; Giesriegl, Ariane; Soyka, Lukas; Trettenhahn, Günter; Kautek, Wolfgang

    2014-05-01

    In situ laser depassivation of plasma electrolytically oxididized (PEO) coatings on aluminium was investigated with nanosecond pulses. Ultraviolet radiation of 266 nm was chosen in order to achieve a high absorption in the dielectric coating. The additive accumulation of laser-induced material defects (incubation) affected the depassivation processes. Incubation occurred only at the edges of the ablation craters irradiated by the outer region of the Gaussian beam profile, where the local fluence is below the ablation threshold. The ablation rate in the spot center did not exhibit an incubation effect. Repassivation was interpreted by a linear combination of a high-field and a point defect growth model. At low overpotentials, field gradients affect the process driving the oxide growth at the buried interface. At high fields, corrosion reactions dominate at the oxide/solution interface.

  9. Fractal analysis of surface micro-topography for a rolled anisotropic thick sheet of aluminium alloy AA2024-T351

    NASA Astrophysics Data System (ADS)

    Pirva, E.; Tudor, A.; Gavrus, A.

    2016-08-01

    Fractal geometry has gained attention in recent years and represents a problem of high interest for the characterization of surface topography. In this study it was analyzed the surface micro-topography for a rolled thick sheet anisotropic metallic material of type 2000 series aluminium alloy (AA2024-T351). In order to analyze and to characterize the corresponding anisotropic surfaces, profile of particular samples were recorded with a specialized apparatus Mitutoyo SJ-301 (Japan). The random nature of the roughness height is described through statistical analysis. The irregularity of the surface profile has been measured using a lot of conventional surface roughness parameters such as: arithmetic average, mean square root, maximum height of the profile, etc. Fractal analysis provides a useful way to characterize the observed spatial complexity of surface micro-topography. For this study it was used the structural function method to calculate two specific fractal parameters: D (fractal dimension) and L (topothesy). The fractal dimension of all samples it's been be calculated by plotting curves on log-log axes.

  10. Experimental investigation on the effects of cooling system on surface quality in high speed milling of an aluminium alloy

    NASA Astrophysics Data System (ADS)

    Chirita, B.; Tampu, N. C.; Brabie, G.; Radu, M. C.

    2016-08-01

    Surface quality is often an important feature of industrial products, not only from the impact it has on the aesthetic aspect but also for the functional role of the parts. High quality surface increases corrosion resistance, assures a longer life cycle for the product and lowers the wear. For a machined part, surface quality is influenced by a series of factors such as the material of the part, the process type, tool geometry, cutting parameters or the cooling system. The choice of the cooling system is especially important, taking into account that the proper conditions will not only assure a superior surface quality, but will also lower the costs and reduce the environmental impact and health risks. The present study aims to investigate the performance of the cooling system and the effect of the cutting parameters on the characteristics of the surfaces resulted from high speed face milling of some parts made of Al 7050-T7451 aluminium alloy. Dry cutting conditions and minimum quantity lubrication (MQL) where used. The results were analysed using analysis of variance (ANOVA).

  11. Impact resistance and hardness modelling of Aluminium alloy welds using square-headed friction-stir welding tool

    NASA Astrophysics Data System (ADS)

    Sudhakar, U.; Srinivas, J., Dr.

    2016-02-01

    This paper proposes modelling and optimization issues relating to friction-stir welding process of aluminium alloys. A specially prepared SS tool of square headed pin profile with cylindrical shoulder is used with a vertical milling machine. Effects of process variables including tool rotation and tool velocity on the weld performance are studied in terms of impact strength and hardness. Three different rotational motions and three welding speeds (feeds) of tool are considered at constant axial load (depth of cut) condition and altogether nine experiments are conducted on a vertical milling machine with specially prepared fixture. Each weld sample is then tested for its impact strength (IS) and hardness independently. A model is developed to correlate the relations between the hardness/impact strength with tool rotation and weld speed using neural networks. The optimized process conditions are predicted to improvise the impact strength and hardness of the weld. Further, the morphology of the weld is studied using SEM to know the material flow characteristics.

  12. Estimating multivariate response surface model with data outliers, case study in enhancing surface layer properties of an aircraft aluminium alloy

    NASA Astrophysics Data System (ADS)

    Widodo, Edy; Kariyam

    2017-03-01

    To determine the input variable settings that create the optimal compromise in response variable used Response Surface Methodology (RSM). There are three primary steps in the RSM problem, namely data collection, modelling, and optimization. In this study focused on the establishment of response surface models, using the assumption that the data produced is correct. Usually the response surface model parameters are estimated by OLS. However, this method is highly sensitive to outliers. Outliers can generate substantial residual and often affect the estimator models. Estimator models produced can be biased and could lead to errors in the determination of the optimal point of fact, that the main purpose of RSM is not reached. Meanwhile, in real life, the collected data often contain some response variable and a set of independent variables. Treat each response separately and apply a single response procedures can result in the wrong interpretation. So we need a development model for the multi-response case. Therefore, it takes a multivariate model of the response surface that is resistant to outliers. As an alternative, in this study discussed on M-estimation as a parameter estimator in multivariate response surface models containing outliers. As an illustration presented a case study on the experimental results to the enhancement of the surface layer of aluminium alloy air by shot peening.

  13. Influence of post-superplastic forming practices on the tensile properties of aluminium-lithium alloys

    SciTech Connect

    Hales, S.J. ); Lippard, H.E. . Dept. of Materials Science)

    1994-06-01

    The effect of thermal processing following superplastic forming on the tensile properties of aluminum-lithium alloys is addressed. The starting materials consisted of alloys 8090, 2090, and X2095 (a Weldalite[trademark] 049 variant) in the form of commercial-grade superplastic sheet. Experience dictates that post-forming practices aimed at a slightly underaged T6 temper produce balanced engineering properties in these alloys. The objective of this study was to assess the potential to use a T5-type temper by eliminating the solution heat treatment and/or cold water quenching steps characteristic of T6 processing. The experimental procedures adopted ensured that the tensile properties compiled were representative of the bulk material Initially, the strengthening behavior of each alloy as a function of temper selection was established. Subsequently, aging practices that resulted in peak strength and balanced properties were identified for the baseline T6 temper and two T5 tempers. The implications for replacing a T6 temper with a T5-type temper, including rapid and slow cooling following forming, are discussed on the basis of the results.

  14. Aluminium/lithium alloy-CFRP hybrid laminate: Fabrication and properties

    SciTech Connect

    Freischmidt, G.; Coutts, R.S.P.; Janardhana, M.N.

    1993-12-31

    Hybrid composite laminates of aluminum and aluminum/lithium alloy sheeting with unidirectional carbon fiber/epoxy plies have been fabricated to produce sheet materials of high strength, low density and reduced fatigue crack growth rate. In an arrangement of one layer of unidirectional carbon fiber reinforced plastic (CFRP) and 2 sheets of 2090-T3 aluminum alloy was used to give a material with a density of 2.20g/cm{sup 3}. Tensile test results gave an ultimate strength of 803MPa, a modulus of 75.7GPa and a 2% offset yield strength of 497MPa. Preliminary fatigue crack growth rate determinations on single edge notch (SEN) specimens show a marked reduction compared to monolithic 2090-T3. Other hybrid laminates using 2024-T3 alloy have also been made and tested. These laminates show reduced tensile properties, however, they appear to have lower fatigue crack growth rates than when using 2090T3 in hybrid form. The fabrication of hybrid laminates included the use of unsupported adhesive film to bond the precured unidirectional carbon fiber composite plies to the aluminum sheeting. This has left a distinct interphase region between the alloy and CFRP which is thought to improve properties through an effective load transfer.

  15. The effect of aluminium on the creep behavior of titanium aluminide alloys

    SciTech Connect

    Nandy, T.K.; Mishra, R.S.; Gogia, A.K.; Banerjee, D.

    1995-03-15

    Small increases in the Al content of Ti{sub 3}Al-Nb alloys are known to improve creep resistance at the expense of the room temperature ductility. Though considerable work has been done on the creep behavior of titanium aluminide alloys, a systematic investigation involving the role of Al on the creep of aluminides is lacking. In the present study the authors have therefore carried out a complete investigation on stress and temperature effects on two alloys with differing Al contents, Ti-24Al-15Nb and Ti-26Al-15Nb (nominal composition in at%) in order to understand the effect of Al in terms of power law creep behavior. The following conclusions are made: (1) A strong Al effect on the creep resistance of O phase alloys in the Ti-Al-Nb systems has been confirmed, through a study of stress and temperature effects on the creep behavior of the Ti-24Al-15Nb and the Ti-26Al-15Nb compositions. (2) It has been shown, however, that the small differences in Al do not affect either the activation energies for creep ({approximately}370 kJ/mole) or the creep mechanism (climb controlled creep with a stress exponent of 4). The activation energies and stress exponents are similar to that observed in single phase O alloys. (3) It is suggested that Al influences creep strength through an intrinsic effect on the pre-exponential term AD{sub o} in the power law creep equation. It is possible that this effect is related to a higher ordering energy of the O phase with increasing Al content.

  16. The fatigue life prediction of aluminium alloy using genetic algorithm and neural network

    NASA Astrophysics Data System (ADS)

    Susmikanti, Mike

    2013-09-01

    The behavior of the fatigue life of the industrial materials is very important. In many cases, the material with experiencing fatigue life cannot be avoided, however, there are many ways to control their behavior. Many investigations of the fatigue life phenomena of alloys have been done, but it is high cost and times consuming computation. This paper report the modeling and simulation approaches to predict the fatigue life behavior of Aluminum Alloys and resolves some problems of computation. First, the simulation using genetic algorithm was utilized to optimize the load to obtain the stress values. These results can be used to provide N-cycle fatigue life of the material. Furthermore, the experimental data was applied as input data in the neural network learning, while the samples data were applied for testing of the training data. Finally, the multilayer perceptron algorithm is applied to predict whether the given data sets in accordance with the fatigue life of the alloy. To achieve rapid convergence, the Levenberg-Marquardt algorithm was also employed. The simulations results shows that the fatigue behaviors of aluminum under pressure can be predicted. In addition, implementation of neural networks successfully identified a model for material fatigue life.

  17. Finite Element Modelling of the Sawing of DC Cast AA2024 Aluminium Alloy Slabs

    SciTech Connect

    Drezet, J.-M.; Ludwig, O.; Heinrich, B.

    2007-04-07

    In the semi-continuous casting of large cross-section rolling sheet ingots of high-strength aluminum alloys (2xxx and 7xxx series), the control of the residual (internal) stresses generated by the non-uniform cooling becomes a necessity. These stresses must be relieved by a thermal treatment before the head and foot of the ingot can be cut. Otherwise, the saw can be caught owing to compressive stresses or cut parts may be ejected thus injuring people or damaging equipment. These high added-value ingots need to be produced in secure conditions. Moreover, a better control of the sawing procedure could allow the suppression of the thermal treatment and therefore save time and energy. By studying the stress build-up during casting and the stress relief during sawing, key parameters for the control and optimization of the processing steps, can be derived. To do so, the direct chill (DC) casting of the AA2024 alloy is modeled with ABAQUS 6.5 with special attention to the thermo-mechanical properties of the alloy. The sawing operation is then simulated by removing mesh elements so as to reproduce the progression of the saw in the ingot. Preliminary results showing the stress relief during sawing accompanied by the risk of saw blocking due to compression or initiating a crack ahead of the saw, are analyzed with an approach based on the rate of strain energy release.

  18. Emission of nanoparticles during friction stir welding (FSW) of aluminium alloys.

    PubMed

    Gomes, J F; Miranda, R M; Santos, T J; Carvalho, P A

    2014-01-01

    Friction stir welding (FSW) is now well established as a welding process capable of joining some different types of metallic materials, as it was (1) found to be a reliable and economical way of producing high quality welds, and (2) considered a "clean" welding process that does not involve fusion of metal, as is the case with other traditional welding processes. The aim of this study was to determine whether the emission of particles during FSW in the nanorange of the most commonly used aluminum (Al) alloys, AA 5083 and AA 6082, originated from the Al alloy itself due to friction of the welding tool against the item that was being welded. Another goal was to measure Al alloys in the alveolar deposited surface area during FSW. Nanoparticles dimensions were predominantly in the 40- and 70-nm range. This study demonstrated that microparticles were also emitted during FSW but due to tool wear. However, the biological relevance and toxic manifestations of these microparticles remain to be determined.

  19. Observations on infiltration of silicon carbide compacts with an aluminium alloy

    NASA Technical Reports Server (NTRS)

    Asthana, R.; Rohatgi, P. K.

    1992-01-01

    The melt infiltration of ceramic particulates permits an opportunity to observe such fundamental materials phenomena as nucleation, dynamic wetting and growth in constrained environments. Experimental observations are presented on the infiltration behavior and matrix microstructures that form when porous compacts of platelet-shaped single crystals of alpha- (hexagonal) silicon carbide are infiltrated with a liquid 2014 Al alloy. The infiltration process involved counter gravity infiltration of suitably tamped and preheated compacts of silicon carbide platelets under an external pressure in a special pressure chamber for a set period, then by solidification of the infiltrant metal in the interstices of the bed at atmospheric pressure.

  20. [Comporison Sduty of Microstructure by Metallographicalk on the Polarized Light and Texture by XRD of CC 5083 and CC 5182 Aluminium Alloy after Cold Rolling and Recrystallization].

    PubMed

    Chen, Ming-biao; Li, Yong-wei; Tan, Yuan-biao; Ma, Min; Wang, Xue-min; Liu, Wen-chang

    2015-03-01

    At present the study of relation between microstructure, texture and performance of CC 5083 aluminium alloy after cold tolling and recrystallization processes is still finitude. So that the use of the CC 5083 aluminium alloy be influenced. Be cased into electrical furnace, hot up with unlimited speed followed the furnace hot up to different temperature and annealed 2h respectively, and be cased into salt-beth furnace, hot up quickly to different temperature and annealed 30 min respectively for CC 5083 and CC 5182 aluminum alloy after cold roling with 91.5% reduction. The microstructure be watched use metallographic microscope, the texture be inspected by XRD. The start temperature of recrystallization and grain grow up temperature within annealing in the electric furnace of CC 5083 aluminum alloy board is 343 degrees C, and the shap of grain after grow up with long strip (the innovation point ); The start temperature of recrystallization within annealling in the salt bath furnace of CC 5083 is 343 degrees C. The start temperature and end temperature of recrystallization within annealling of CC 5083 and CC 5182 aluminum alloy is 371 degrees C. The grain grow up outstanding of cold rooled CC 5152 aluminum alloy after annealed with 454 degrees C in the electric furnace and salt bath furnace. The start temperature of grain grow up of CC 5083 alluminurn alloy annealed in the electric furnace and salt bath furnace respectively is higher than the start temperature of grain grow up of CC 5182 alluminum alloy annealed in the electric furnace and salt bath furnace respectively. The strat temperature of recrystallization grain grow up is higher than which annealled with other three manner annealing process. The recrystallization temperature of CC 5182 annealed in the salt bath furnace is higher than which annealed in the electric furnace. The recrystallization temperature of the surface layer of CC 5083 and CC 5182 aluminum alloy is higher than the inner layer (the innovation

  1. Fatigue properties of as-welded AA6005 and AA6082 aluminium alloys in T1 and T5 temper condition

    SciTech Connect

    Ranes, M.; Kluken, A.O.; Midling, O.T.

    1996-12-31

    The present investigation was undertaken to determine the as-welded fatigue properties of AA6005 and AA6082 aluminium alloys in the T1 and T5 temper conditions. Extruded flat bars of the base materials were welded by means of the Metal Inert Gas (MIG), Friction Stir and Plasma-keyhole techniques. The latter technique was only employed for alloy AA6005. The weldments were subsequently fatigue tested at a load ratio of 0.5. The results revealed that the friction stir welds had fatigue properties superior to both the MIG and Plasma-keyhole welds. For alloy AA6005 the fatigue properties of the friction stir weld was close to the base material properties. The shortest fatigue life was exhibited by the MIG welds. The fatigue strength of these weldments appear to be affected by the base metal temper condition. For this reason, MIG welds on alloy AA6082 should be performed in the T5 temper condition, while alloy AA6005 should be welded in the T1 temper condition. Plasma-keyhole welds should be performed on T1 tempered material rather than on T5 tempered material. Repair welding of MIG welds on the T1 tempered base material resulted in improved fatigue properties of AA6082 weldments, while the fatigue strength of AA6005 weldments remained unaffected. The fatigue properties of MIG welds in alloy AA6082 correspond well with the static strength properties.

  2. ``Long-life`` aluminium brazing alloys for automotive radiators -- a ten-year retrospective

    SciTech Connect

    Scott, A.C.; Woods, R.A.

    1998-12-31

    A class of corrosion-resistant brazing sheet materials, generally referred to as ``long-life alloys,`` has been in widespread use in brazed aluminum automobile radiators for over ten years. K319 tube material was initially introduced in 1986 to address the problem of road-salt-induced, outside-in corrosion of tubes in vacuum-brazed aluminum radiators, The development history, metallurgy, and field performance of long-life radiator brazing sheet are reviewed. This material utilizes the familiar sacrificial layer concept to improve corrosion resistance; however, it is unusual in that the layer is not introduced by conventional cladding means during sheet manufacture, but rather develops in situ by metallurgical transformations which occur during the brazing cycle. The sacrificial layer, about 25 mV anodic to the core alloy, increases by an order of magnitude the time-to-perforation of radiator tube sheet tested in cyclic acidified salt spray (SWAAT), which mimics the corrosion morphology observed in the field. Radiators examined after ten years of field service show excellent corrosion resistance, as predicted by SWAAT.

  3. Aluminium plasmonics

    SciTech Connect

    Gerard, Davy; Gray, Stephen K.

    2014-12-15

    In this study, we present an overview of 'aluminium plasmonics', i.e. the study of both fundamental and practical aspects of surface plasmon excitations in aluminium structures, in particular thin films and metal nanoparticles. After a brief introduction noting both some recent and historical contributions to aluminium plasmonics, we discuss the optical properties of aluminium and aluminium nanostructures and highlight a few selected studies in a host of areas ranging from fluorescence to data storage.

  4. Aluminium plasmonics

    NASA Astrophysics Data System (ADS)

    Gérard, Davy; Gray, Stephen K.

    2015-05-01

    We present an overview of ‘aluminium plasmonics’, i.e. the study of both fundamental and practical aspects of surface plasmon excitations in aluminium structures, in particular thin films and metal nanoparticles. After a brief introduction noting both some recent and historical contributions to aluminium plasmonics, we discuss the optical properties of aluminium and aluminium nanostructures and highlight a few selected studies in a host of areas ranging from fluorescence to data storage.

  5. On the melt infiltration of copper coated silicon carbide with an aluminium alloy

    NASA Technical Reports Server (NTRS)

    Asthana, R.; Rohatgi, P. K.

    1992-01-01

    Pressure-assisted infiltration of porous compacts of Cu coated and uncoated single crystals of platelet shaped alpha (hexagonal) SiC was used to study infiltration dynamics and particulate wettability with a 2014 Al alloy. The infiltration lengths were measured for a range of experimental variables which included infiltration pressure, infiltration time, and SiC size. A threshold pressure (P(th)) for flow initiation through compacts was identified from an analysis of infiltration data; P(th) decreased while penetration lengths increased with increasing SiC size (more fundamentally, due to changes in interparticle pore size) and with increasing infiltration times. Cu coated SiC led to lower P(th) and 60-80 percent larger penetration lengths compared to uncoated SiC under identical processing conditions.

  6. Porosity evolution in additively manufactured aluminium alloy during high temperature exposure

    NASA Astrophysics Data System (ADS)

    Bai, J.; Ding, H. L.; Gu, J. L.; Wang, X. S.; Qiu, H.

    2017-01-01

    A 2319 aluminum alloy is deposited by the Wire+Arc Additive Manufacturing technology with Cold Metal Transfer process. Porosity that are both existing in the as-deposited and as-heat treated state metal are revealed by optical microscopy and quantitatively analyzed. It explains the reason why the newly initiated pores are easily tend to gather between each layer around the fusion line zone for the WAAM metal after heat treatment. The inner morphology of the pores are demonstrated by Scanning Electron Microscopy. Porosity evolution and distribution during high temperature exposure are demonstrated. Thus two porosity growth and number increase mechanisms are proposed eventually, providing theoretical basis for related material design and process optimization.

  7. Investigation of surface finishing of carbon based coated tools for dry deep drawing of aluminium alloys

    NASA Astrophysics Data System (ADS)

    Steiner, J.; Andreas, K.; Merklein, M.

    2016-11-01

    Global trends like growing environmental awareness and demand for resource efficiency motivate an abandonment of lubricants in metal forming. However, dry forming evokes increased friction and wear. Especially, dry deep drawing of aluminum alloys leads to intensive interaction between tool and workpiece due to its high adhesion tendency. One approach to improve the tribological behavior is the application of carbon based coatings. These coatings are characterized by high wear resistance. In order to investigate the potential of carbon based coatings for dry deep drawing, friction and wear behavior of different coating compositions are evaluated in strip drawing tests. This setup is used to model the tribological conditions in the flange area of deep drawing operations. The tribological behavior of tetrahedral amorphous (ta-C) and hydrogenated amorphous carbon coatings with and without tungsten modification (a-C:H:W, a-C:H) is investigated. The influence of tool topography is analyzed by applying different surface finishing. The results show reduced friction with decreased roughness for coated tools. Besides tool topography the coating type determines the tribological conditions. Smooth tools with ta-C and a-C:H coatings reveal low friction and prevent adhesive wear. In contrast, smooth a-C:H:W coated tools only lead to slight improvement compared to rough, uncoated specimen.

  8. Elemental electron energy loss mapping of a precipitate in a multi-component aluminium alloy.

    PubMed

    Mørtsell, Eva A; Wenner, Sigurd; Longo, Paolo; Andersen, Sigmund J; Marioara, Calin D; Holmestad, Randi

    2016-07-01

    The elemental distribution of a precipitate cross section, situated in a lean Al-Mg-Si-Cu-Ag-Ge alloy, has been investigated in detail by electron energy loss spectroscopy (EELS) and aberration corrected high angle annular dark field scanning transmission electron microscopy (HAADF-STEM). A correlative analysis of the EELS data is connected to the results and discussed in detail. The energy loss maps for all relevant elements were recorded simultaneously. The good spatial resolution allows elemental distribution to be evaluated, such as by correlation functions, in addition to being compared with the HAADF image. The fcc-Al lattice and the hexagonal Si-network within the precipitates were resolved by EELS. The combination of EELS and HAADF-STEM demonstrated that some atomic columns consist of mixed elements, a result that would be very uncertain based on one of the techniques alone. EELS elemental mapping combined with a correlative analysis have great potential for identification and quantification of small amounts of elements at the atomic scale.

  9. The effect of welding parameters on surface quality of AA6351 aluminium alloy

    NASA Astrophysics Data System (ADS)

    Yacob, S.; MAli, M. A.; Ahsan, Q.; Ariffin, N.; Ali, R.; Arshad, A.; Wahab, M. I. A.; Ismail, S. A.; Roji, NS M.; Din, W. B. W.; Zakaria, M. H.; Abdullah, A.; Yusof, M. I.; Kamarulzaman, K. Z.; Mahyuddin, A.; Hamzah, M. N.; Roslan, R.

    2015-12-01

    In the present work, the effects of gas metal arc welding-cold metal transfer (GMAW-CMT) parameters on surface roughness are experimentally assessed. The purpose of this study is to develop a better understanding of the effects of welding speed, material thickness and contact tip to work distance on the surface roughness. Experiments are conducted using single pass gas metal arc welding-cold metal transfer (GMAW-CMT) welding technique to join the material. The material used in this experiment was AA6351 aluminum alloy with the thickness of 5mm and 6mm. A Mahr Marsuft XR 20 machine was used to measure the average roughness (Ra) of AA6351 joints. The main and interaction effect analysis was carried out to identify process parameters that affect the surface roughness. The results show that all the input process parameters affect the surface roughness of AA6351 joints. Additionally, the average roughness (Ra) results also show a decreasing trend with increased of welding speed. It is proven that gas metal arc welding-cold metal transfer (GMAW-CMT)welding process has been successful in term of providing weld joint of good surface quality for AA6351 based on the low value surface roughness condition obtained in this setup. The outcome of this experimental shall be valuable for future fabrication process in order to obtained high good quality weld.

  10. Experimental and Numerical Study of Needle Peening Effects in Aluminium Alloy 2024-T3 Sheets

    NASA Astrophysics Data System (ADS)

    Mendez Romero, Julio Alberto

    Montreal as part of previous shot peening research. Saturation tests were done to determine the deflection at saturation for different peening parameters. The specimen deflection was measured using the standard Almen gauge used as part of routinary process control. Due to the aluminium magnetic incompatibility with the Almen gauge, the deformed specimen profile was measured using a Coordinate Measuring Machine (CMM). Repeatability of the process was demonstrated and the deflection at saturation, as well as the saturation time, was obtained. The indentation diameters created by impacts for different operating pressures were measured using microscopic photography. It was determined that the specimen deformation, as well as the indentation diameter, is larger when the operating pressure increases. Treatment of the test samples using the same peening parameters resulted in a variable indentation diameter. This is explained by the velocity variations detected during the equipment characterization. The added value that needle peening could provide to existing peening techniques is that, in principle, uniformity in the indentation diameters is easier to achieve as all impacts are normal and there is no loss of energy due to media interaction. The last experimental test was to determine the induced residual stress by means of X-ray Diffraction (XRD) for one specimen at saturation. An FE model heavily inspired by previous shot peening modeling was developed to simulate needle peening. The parameters obtained during the characterization of the equipment were taken as boundary conditions. Initially, the case of a single impacts was studied. Good accordance between the simulated and the average experimental indentation diameters was obtained, except for the lowest pressure studied. The overestimation of the indentation diameter could stem from the method used to measure the simulated diameter. Coverage estimation, and therefore indentation diameters remain an open line of research in

  11. The effects of short pulse laser surface cleaning on porosity formation and reduction in laser welding of aluminium alloy for automotive component manufacture

    NASA Astrophysics Data System (ADS)

    AlShaer, A. W.; Li, L.; Mistry, A.

    2014-12-01

    Laser welding of aluminium alloys typically results in porosity in the fusion zones, leading to poor mechanical and corrosion performances. Mechanical and chemical cleaning of surfaces has been used previously to remove contaminants for weld joint preparations. However, these methods are slow, ineffective (e.g. due to hydrogen trapping) or lead to environmental hazards. This paper reports the effects of short pulsed laser surface cleaning on porosity formation and reduction in laser welding of AC-170PX (AA6014) aluminium sheets (coated with Ti/Zr and lubricated using a dry lubricant AlO70) with two types of joints: fillet edge and flange couch, using an AA4043 filler wire for automotive component assembly. The effect of laser cleaning on porosity reduction during laser welding using a filler wire has not been reported before. In this work, porosity and weld fusion zone geometry were examined prior to and after laser cleaning. The nanosecond pulsed Nd:YAG laser cleaning was found to reduce porosity significantly in the weld fusion zones. For the fillet edge welds, porosity was reduced to less than 0.5% compared with 10-80% without laser cleaning. For flange couch welds, porosity was reduced to 0.23-0.8% with laser cleaning from 0.7% to 4.3% without laser cleaning. This has been found to be due to the elimination of contaminations and oxide layers that contribute to the porosity formation. The laser cleaning is based on thermal ablation. This research focuses on porosity reduction in laser welding of aluminium alloy. Weld quality was investigated for two joints, fillet edge and flange couch joints. The effect of laser cleaning on porosity reduction after welding was investigated. It was found that laser cleaning reduced porosity less than 1% in both joints. Weld dimensions and strength were evaluated and discussed for both types of joints.

  12. Effects of processing parameters on the extrusion by continuous variable cross-section direct extrusion with 7A09 aluminium alloy

    NASA Astrophysics Data System (ADS)

    Li, Feng; Wu, Hongbin; Qin, Minghan

    2016-02-01

    In order to study the effects of processing parameters on the continuous variable cross-section direct extrusion (CVCDE), taking 7A09 aluminium alloy for example, the extrusion speed and forming temperature and the friction factor as key processing parameters are applied to research by finite element (FE) simulation. The research result showed that the extrusion speed had a significant influence on the maximum temperature of the billet, at the same time, both decreasing the friction factor and increasing forming temperature within a certain range were beneficial to reduce extrusion load. Both forming temperature and the extrusion speed were inversely linked to extrusion load, but the friction factor was directly proportional to extrusion load. Forming temperature had a far more important influence on extrusion load by comparison: when forming temperature increased from 380∘ to 430∘C, the peak value of extrusion load decreased by 25.6% and the flow uniformity of extruded product got improved. The process window based on both the press limit and surface defects limit was established and the most reasonable forming temperature was 405∘C under this process condition, which provided theoretical basis for formulation process of 7A09 aluminium alloy on the CVCDE extrusion.

  13. Design and operation of an aluminium alloy tank using doped Na3AlH6 in kg scale for hydrogen storage

    NASA Astrophysics Data System (ADS)

    Urbanczyk, R.; Peinecke, K.; Meggouh, M.; Minne, P.; Peil, S.; Bathen, D.; Felderhoff, M.

    2016-08-01

    In this publication the authors present an aluminium alloy tank for hydrogen storage using 1921 g of Na3AlH6 doped with 4 mol% of TiCl3 and 8 mol% of activated carbon. The tank and the heat exchangers are manufactured by extrusion moulding of Al-Mg-Si based alloys. EN AW 6082 T6 alloy is used for the tank and a specifically developed alloy with a composition similar to EN AW 6060 T6 is used for the heat exchangers. The three heat exchangers have a corrugated profile to enhance the surface area for heat transfer. The doped complex hydride Na3AlH6 is densified to a powder density of 0.62 g cm-3. The hydrogenation experiments are carried out at 2.5 MPa. During one of the dehydrogenation experiments approximately 38 g of hydrogen is released, accounting for gravimetric hydrogen density of 2.0 mass-%. With this tank 15 hydrogenation and 16 dehydrogenation tests are carried out.

  14. Some preliminary evaluations of black coating on aluminium AA2219 alloy produced by plasma electrolytic oxidation (PEO) process for space applications

    NASA Astrophysics Data System (ADS)

    Shrestha, S.; Merstallinger, A.; Sickert, D.; Dunn, B. D.

    2003-09-01

    This paper describes the results of a study of a black coating produced on aluminium AA2219 alloy using a process that involves creation of a hard ceramic oxide layer on the surface of the alloy by plasma electrolytic oxidation (PEO) known as the 'KERONITE®' process. Coating microstructure has been examined and the coating characteristics such as porosity, hardness, adhesion and phase composition were measured. The thermo-optical properties such as solar absorptance 'as' and normal infrared emittance 'en-IR' of the coating were measured in the 'as-prepared' condition and after environmental exposures to humidity, thermal cycling and UV-radiation in vacuum and to thermal shock. Comparison was made with alternative coatings produced using standard black anodising processes. The study also looked at the cold welding and friction behaviours of the coated alloy in vacuum and in an ambient laboratory environment. Standard spacecraft materials tests were conducted on the coated disc against an AISI 52100 steel ball and also against a coated pin using a pin-on-disc apparatus. Parameters such as friction coefficient and wear depth were measured and the cold welding behaviours were investigated. Test results were compared with the data generated for NiCr plated and anodised coatings. Corrosion performance was assessed using a salt spray exposure test and using an accelerated electrochemical test method. In addition, the study looked at the effect of post coating sealing with a sol-gel solution.

  15. Finite element modelling of shot peening and peen forming processes and characterisation of peened AA2024-T351 aluminium alloy

    NASA Astrophysics Data System (ADS)

    Gariepy, Alexandre

    The main purpose of this thesis was to develop and validate finite element (FE) simulation tools for shot peening and peen forming. The specific aim was to achieve quantitatively accurate predictions for both processes and demonstrate the potential of reliable FE modelling for scientific investigation and industrial applications. First, an improved dynamic impact model that takes into account the stochastic nature of shot peening was proposed by carefully studying its dimensions, introducing a dispersion of shot sizes and significantly reducing its computational cost. In addition, cyclic mechanical testing was conducted to define a suitable material constitutive theory for aluminium alloy (AA) 2024-T3/T351 subjected to shot peening. By combining a realistic shot peening model with an appropriate material law, fairly good residual stress predictions were achieved for three different sets of shot peening parameters. Second, an experimental and numerical characterization of AA2024-T351 shot peened with parameters representative of fatigue life improvement applications was conducted. Multiple techniques, such as micro-indentation, residual stress determination and electron backscatter diffraction, were combined to gain a better understanding of the influence of shot peening on the material. The potential uses of finite element simulation to complement experimental data were also studied. The material heterogeneity arising from the random impact sequence was investigated and it was found that the impact modelling methodology could provide useful information on such heterogeneities. Third, a novel peen forming simulation methodology was introduced. The impact model provided the necessary input data as part of a multiscale approach. Numerically calculated unbalanced induced stress profiles were input into shell elements and the deformed shape after peen forming was computed as a springback analysis. In addition, a simple interpolation method was proposed to model the

  16. Extraction spectrophotometric determination of vanadium in natural waters and aluminium alloys using pyridyl azo resorcinol (PAR) and iodo-nitro-tetrazolium chloride (INT).

    PubMed

    Gavazov, K; Simeonova, Z; Alexandrov, A

    2000-06-30

    Extraction-spectrophotometric methods are developed for the determination of vanadium content in natural waters and aluminium alloys. They are based on the formation and subsequent extraction into chloroform of the ternary ion association complex of V(V) with PAR and INT in the presence of CDTA and NH(4)F as masking agents. Optimum pH range of the reaction is 5.5-7.5. Maximum absorbance of the extracted complex is at 560 nm. The method for determination of V(V) in drinking waters can be successfully applied at a concentration level of 3 ppb and higher without additional pre-concentration. Among studied more than 30 foreign ions potentially present in natural waters only Ca(II) can interfere. It is removed by precipitation as CaF(2) and filtration. A 40-fold excess of V(IV) does not interfere with determination of V(V) and can also be determined indirectly (after oxidation to V(V)). The proposed method is applied to analysis of model mixtures as well as to the analysis of tap and mineral waters. Beer's law is obeyed for up to 15 mug of V(V) in 40 ml aqueous phase. The accuracy and precision are reasonable. The RSD is in the range 6.5-23.2% for determination of 6.3 ppb V(V). The procedure for analysis of aluminium alloys differs from the procedure for analysis of waters by the order of introduction of the reagents. The macrocomponent does not interfere and is not separated. Mg, Mn, Cu, Zn, Fe, Cr, Ti and Zr do not interfere. A 25-fold excess of Ni interferes. The method is tested in the analysis of reference standards containing 0.005 and 0.007% V, respectively. The RSD is 1.4%.

  17. The effect of surface pre-conditioning treatments on the local composition of Zr-based conversion coatings formed on aluminium alloys

    NASA Astrophysics Data System (ADS)

    Cerezo, J.; Vandendael, I.; Posner, R.; de Wit, J. H. W.; Mol, J. M. C.; Terryn, H.

    2016-03-01

    This study investigates the effect of different alkaline, acidic and thermal pre-conditioning treatments applied to different Al alloy surfaces. The obtained results are compared to the characteristics of Zr-based conversion coatings that were subsequently generated on top of these substrates. Focus is laid on typical elemental distributions on the sample surfaces, in particular on the amount of precipitated functional additives such as Cu species that are present in the substrate matrix as well as in the conversion bath solutions. To this aim, Field Emission Auger Electron spectra, depth profiles and surface maps with superior local resolution were acquired and compared to scanning electron microscopy images of the sample. The results show how de-alloying processes, which occur at and around intermetallic particles in the Al matrix during typical industrial alkaline or acidic cleaning procedures, provide a significant source of crystallization cores for any following coating processes. This is in particular due for Cu-species, as the resulting local Cu structures on the surface strongly affect the film formation and compositions of state-of-the-art Zr-based films. The findings are highly relevant for industrial treatments of aluminium surfaces, especially for those that undergo corrosion protection and painting process steps prior to usage.

  18. Influences of process parameters on tensile strength of friction stir welded cast A319 aluminium alloy joints

    NASA Astrophysics Data System (ADS)

    Jayaraman, M.; Sivasubramanian, R.; Balasubramanian, V.; Babu, S.

    2009-04-01

    Fusion welding of cast A319 (Al-Si-Cu) alloy will lead to many problems including porosity, micro-fissuring, and hot cracking. Friction Stir Welding (FSW) can be used to weld A319 alloy without these defects. In this investigation, an attempt has been made to study the effect of FSW process parameters on the tensile strength of A319 alloy welded joints. Joints were made using different combinations of tool rotation speed, welding speed, and axial force, each at four levels. The quality of weld zone was analyzed using macrostructure and microstructure analysis. Tensile strength of the joints were evaluated and correlated with the weld zone microstructure. The joint fabricated with a 1200 rpm tool rotation speed, 40 mm/min welding speed, and 4 kN axial force showed superior tensile strength compared with the other joints.

  19. Microstructural evolution and age hardening in aluminium alloys: Atom probe field-ion microscopy and transmission electron microscopy studies

    SciTech Connect

    Ringer, S.P.; Hono, K.

    2000-02-01

    This paper examines the microstructural evolution in selected aluminum alloys based on commercial age hardenable 2000, 6000, and 7000 series alloys. Atom probe field-ion microscopy and transmission electron microscopy have been used to examine the effects of microalloying and the origins of hardening. The combined application of these techniques is particularly important in the study of nanoscale precipitation processes. It is shown that the nature and kinetics of the precipitation process depend on the solute-solute interactions that produce solute clusters. The solute clusters precede the formation of GP zones or precipitation, and have a defining role on the nature and kinetics of the subsequent precipitation processes. Moreover, interactions between solute clustering and dislocations can have a significant hardening effect, the origins of which seem to be distinctly different from the conventional notion of precipitation hardening.

  20. Impact properties of the aircraft cast aluminium alloy Al-7Si0.6Mg (A357)

    NASA Astrophysics Data System (ADS)

    Alexopoulos, N. D.

    2010-06-01

    The impact mechanical properties of the widely used in the aeronautics A357 cast aluminum alloy were investigated by exploiting experiments on an instrumented Charpy impact testing machine. The evaluated impact properties for 25 different artificial aging heat treatment conditions were analyzed and discussed in conjunction with the respective tensile properties. Correlations are proposed to establish useful relationships between impact resistance and tensile strain energy density properties. The established correlations, which are well supported by the performed experiments, can be used to estimate the tensile ductility and toughness of the A357 cast aluminum alloy from the Charpy impact test. Performed fractographic analyses were supporting the physically arbitrary correlation between tensile strain energy density and impact resistance.

  1. Fatigue FEM analysis in the case of brazed aluminium alloy 3L59 used in aeronautical industry

    NASA Astrophysics Data System (ADS)

    Dimitrescu, A.; Amza, Gh; Niţoi, D. F.; Amza, C. Gh; Apostolescu, Z.

    2016-08-01

    The use, on a larger scale, of brazed aluminum alloys in the aerospace industry led to the need for a detailed study of the assemblies behavior. These are built from 6061 aluminum aloy (3L59) brazed with aluminum aloy A103. Therefore, a finit element simulation (FEM) of durability is necessary, that consists in the observation of gradual deterioration until failure. These studies are required and are previous to the stage of the producing the assembly and test it by traditional methods.

  2. Investigation of the aluminium-aluminium oxide reversible transformation as observed by hot stage electron microscopy.

    NASA Technical Reports Server (NTRS)

    Grove, C. A.; Judd, G.; Ansell, G. S.

    1972-01-01

    Thin foils of high purity aluminium and an Al-Al2O3 SAP type of alloy were oxidised in a specially designed hot stage specimen chamber in an electron microscope. Below 450 C, amorphous aluminium oxide formed on the foil surface and was first detectable at foil edges, holes, and pits. Islands of aluminium then nucleated in this amorphous oxide. The aluminium islands displayed either a lateral growth with eventual coalescence with other islands, or a reoxidation process which caused the islands to disappear. The aluminium island formation was determined to be related to the presence of the electron beam. A mechanism based upon electron charging due to the electron beam was proposed to explain the nucleation, growth, coalescence, disappearance, and geometry of the aluminium islands.

  3. Parameter Design in Fusion Welding of AA 6061 Aluminium Alloy using Desirability Grey Relational Analysis (DGRA) Method

    NASA Astrophysics Data System (ADS)

    Adalarasan, R.; Santhanakumar, M.

    2015-01-01

    In the present work, yield strength, ultimate strength and micro-hardness of the lap joints formed with Al 6061 alloy sheets by using the processes of Tungsten Inert Gas (TIG) welding and Metal Inert Gas (MIG) welding were studied for various combinations of the welding parameters. The parameters taken for study include welding current, voltage, welding speed and inert gas flow rate. Taguchi's L9 orthogonal array was used to conduct the experiments and an integrated technique of desirability grey relational analysis was disclosed for optimizing the welding parameters. The ignored robustness in desirability approach is compensated by the grey relational approach to predict the optimal setting of input parameters for the TIG and MIG welding processes which were validated through the confirmation experiments.

  4. Comparison between diffraction contrast tomography and high-energy diffraction microscopy on a slightly deformed aluminium alloy.

    PubMed

    Renversade, Loïc; Quey, Romain; Ludwig, Wolfgang; Menasche, David; Maddali, Siddharth; Suter, Robert M; Borbély, András

    2016-01-01

    The grain structure of an Al-0.3 wt%Mn alloy deformed to 1% strain was reconstructed using diffraction contrast tomography (DCT) and high-energy diffraction microscopy (HEDM). 14 equally spaced HEDM layers were acquired and their exact location within the DCT volume was determined using a generic algorithm minimizing a function of the local disorientations between the two data sets. The microstructures were then compared in terms of the mean crystal orientations and shapes of the grains. The comparison shows that DCT can detect subgrain boundaries with disorientations as low as 1° and that HEDM and DCT grain boundaries are on average 4 µm apart from each other. The results are important for studies targeting the determination of grain volume. For the case of a polycrystal with an average grain size of about 100 µm, a relative deviation of about ≤10% was found between the two techniques.

  5. The corrosion protection of AA2024-T3 aluminium alloy by leaching of lithium-containing salts from organic coatings.

    PubMed

    Visser, Peter; Liu, Yanwen; Zhou, Xiaorong; Hashimoto, Teruo; Thompson, George E; Lyon, Stuart B; van der Ven, Leendert G J; Mol, Arjan J M C; Terryn, Herman A

    2015-01-01

    Lithium carbonate and lithium oxalate were incorporated as leachable corrosion inhibitors in model organic coatings for the protection of AA2024-T3. The coated samples were artificially damaged with a scribe. It was found that the lithium-salts are able to leach from the organic coating and form a protective layer in the scribe on AA2024-T3 under neutral salt spray conditions. The present paper shows the first observation and analysis of these corrosion protective layers, generated from lithium-salt loaded organic coatings. The scribed areas were examined by scanning and transmission electron microscopy before and after neutral salt spray exposure (ASTM-B117). The protective layers typically consist of three different layered regions, including a relatively dense layer near the alloy substrate, a porous middle layer and a flake-shaped outer layer, with lithium uniformly distributed throughout all three layers. Scanning electron microscopy and white light interferometry surface roughness measurements demonstrate that the formation of the layer occurs rapidly and, therefore provides an effective inhibition mechanism. Based on the observation of this work, a mechanism is proposed for the formation of these protective layers.

  6. Aluminium alloyed iron-silicide/silicon solar cells: A simple approach for low cost environmental-friendly photovoltaic technology.

    PubMed

    Kumar Dalapati, Goutam; Masudy-Panah, Saeid; Kumar, Avishek; Cheh Tan, Cheng; Ru Tan, Hui; Chi, Dongzhi

    2015-12-03

    This work demonstrates the fabrication of silicide/silicon based solar cell towards the development of low cost and environmental friendly photovoltaic technology. A heterostructure solar cells using metallic alpha phase (α-phase) aluminum alloyed iron silicide (FeSi(Al)) on n-type silicon is fabricated with an efficiency of 0.8%. The fabricated device has an open circuit voltage and fill-factor of 240 mV and 60%, respectively. Performance of the device was improved by about 7 fold to 5.1% through the interface engineering. The α-phase FeSi(Al)/silicon solar cell devices have promising photovoltaic characteristic with an open circuit voltage, short-circuit current and a fill factor (FF) of 425 mV, 18.5 mA/cm(2), and 64%, respectively. The significant improvement of α-phase FeSi(Al)/n-Si solar cells is due to the formation p(+-)n homojunction through the formation of re-grown crystalline silicon layer (~5-10 nm) at the silicide/silicon interface. Thickness of the regrown silicon layer is crucial for the silicide/silicon based photovoltaic devices. Performance of the α-FeSi(Al)/n-Si solar cells significantly depends on the thickness of α-FeSi(Al) layer and process temperature during the device fabrication. This study will open up new opportunities for the Si based photovoltaic technology using a simple, sustainable, and los cost method.

  7. Aluminium alloyed iron-silicide/silicon solar cells: A simple approach for low cost environmental-friendly photovoltaic technology

    PubMed Central

    Kumar Dalapati, Goutam; Masudy-Panah, Saeid; Kumar, Avishek; Cheh Tan, Cheng; Ru Tan, Hui; Chi, Dongzhi

    2015-01-01

    This work demonstrates the fabrication of silicide/silicon based solar cell towards the development of low cost and environmental friendly photovoltaic technology. A heterostructure solar cells using metallic alpha phase (α-phase) aluminum alloyed iron silicide (FeSi(Al)) on n-type silicon is fabricated with an efficiency of 0.8%. The fabricated device has an open circuit voltage and fill-factor of 240 mV and 60%, respectively. Performance of the device was improved by about 7 fold to 5.1% through the interface engineering. The α-phase FeSi(Al)/silicon solar cell devices have promising photovoltaic characteristic with an open circuit voltage, short-circuit current and a fill factor (FF) of 425 mV, 18.5 mA/cm2, and 64%, respectively. The significant improvement of α-phase FeSi(Al)/n-Si solar cells is due to the formation p+−n homojunction through the formation of re-grown crystalline silicon layer (~5–10 nm) at the silicide/silicon interface. Thickness of the regrown silicon layer is crucial for the silicide/silicon based photovoltaic devices. Performance of the α-FeSi(Al)/n-Si solar cells significantly depends on the thickness of α-FeSi(Al) layer and process temperature during the device fabrication. This study will open up new opportunities for the Si based photovoltaic technology using a simple, sustainable, and los cost method. PMID:26632759

  8. Aluminium in human sweat.

    PubMed

    Minshall, Clare; Nadal, Jodie; Exley, Christopher

    2014-01-01

    It is of burgeoning importance that the human body burden of aluminium is understood and is measured. There are surprisingly few data to describe human excretion of systemic aluminium and almost no reliable data which relate to aluminium in sweat. We have measured the aluminium content of sweat in 20 healthy volunteers following mild exercise. The concentration of aluminium ranged from 329 to 5329μg/L. These data equate to a daily excretion of between 234 and 7192μg aluminium and they strongly suggest that perspiration is the major route of excretion of systemic aluminium in humans.

  9. IEC 61267: Feasibility of type 1100 aluminium and a copper/aluminium combination for RQA beam qualities.

    PubMed

    Leong, David L; Rainford, Louise; Zhao, Wei; Brennan, Patrick C

    2016-01-01

    In the course of performance acceptance testing, benchmarking or quality control of X-ray imaging systems, it is sometimes necessary to harden the X-ray beam spectrum. IEC 61267 specifies materials and methods to accomplish beam hardening and, unfortunately, requires the use of 99.9% pure aluminium (Alloy 1190) for the RQA beam quality, which is expensive and difficult to obtain. Less expensive and more readily available filters, such as Alloy 1100 (99.0% pure) aluminium and copper/aluminium combinations, have been used clinically to produce RQA series without rigorous scientific investigation to support their use. In this paper, simulation and experimental methods are developed to determine the differences in beam quality using Alloy 1190 and Alloy 1100. Additional simulation investigated copper/aluminium combinations to produce RQA5 and outputs from this simulation are verified with laboratory tests using different filter samples. The results of the study demonstrate that although Alloy 1100 produces a harder beam spectrum compared to Alloy 1190, it is a reasonable substitute. A combination filter of 0.5 mm copper and 2 mm aluminium produced a spectrum closer to that of Alloy 1190 than Alloy 1100 with the added benefits of lower exposures and lower batch variability.

  10. Human exposure to aluminium.

    PubMed

    Exley, Christopher

    2013-10-01

    Human activities have circumvented the efficient geochemical cycling of aluminium within the lithosphere and therewith opened a door, which was previously only ajar, onto the biotic cycle to instigate and promote the accumulation of aluminium in biota and especially humans. Neither these relatively recent activities nor the entry of aluminium into the living cycle are showing any signs of abating and it is thus now imperative that we understand as fully as possible how humans are exposed to aluminium and the future consequences of a burgeoning exposure and body burden. The aluminium age is upon us and there is now an urgent need to understand how to live safely and effectively with aluminium.

  11. Effects of as-cast and wrought Cobalt-Chrome-Molybdenum and Titanium-Aluminium-Vanadium alloys on cytokine gene expression and protein secretion in J774A.1 macrophages.

    PubMed

    Jakobsen, Stig S; Larsen, A; Stoltenberg, M; Bruun, J M; Soballe, K

    2007-09-11

    Insertion of metal implants is associated with a possible change in the delicate balance between pro- and anti-inflammatory proteins, probably leading to an unfavourable predominantly pro-inflammatory milieu. The most likely cause is an inappropriate activation of macrophages in close relation to the metal implant and wear-products. The aim of the present study was to compare surfaces of as-cast and wrought Cobalt-Chrome-Molybdenum (CoCrMo) alloys and Titanium-Aluminium-Vanadium (TiAlV) alloy when incubated with mouse macrophage J774A.1 cell cultures. Changes in pro- and anti-inflammatory cytokines (TNF-alpha, IL-6, IL-alpha, IL-1beta, IL-10) and proteins known to induce proliferation (M-CSF), chemotaxis (MCP-1) and osteogenesis (TGF-beta, OPG) were determined by ELISA and Real Time reverse transcriptase - PCR (Real Time rt-PCR). Lactate dehydrogenase (LDH) was measured in the medium to asses the cell viability. Surface properties of the discs were characterised with a profilometer and with energy dispersive X-ray spectroscopy. We here report, for the first time, that the prosthetic material surface (non-phagocytable) of as-cast high carbon CoCrMo reduces the pro-inflammatory cytokine IL-6 transcription, the chemokine MCP-1 secretion, and M-CSF secretion by 77%, 36%, and 62%, respectively. Furthermore, we found that reducing surface roughness did not affect this reduction. The results suggest that as-cast CoCrMo alloy is more inert than wrought CoCrMo and wrought TiAlV alloys and could prove to be a superior implant material generating less inflammation which might result in less osteolysis.

  12. Experimental investigations on mechanical behavior of aluminium metal matrix composites

    NASA Astrophysics Data System (ADS)

    Rajesh, A. M.; Kaleemulla, Mohammed

    2016-09-01

    Today we are widely using aluminium based metal matrix composite for structural, aerospace, marine and automobile applications for its light weight, high strength and low production cost. The purpose of designing metal matrix composite is to add the desirable attributes of metals and ceramics to the base metal. In this study we developed aluminium metal matrix hybrid composite by reinforced Aluminium7075 alloy with silicon carbide (SiC) and aluminium oxide (alumina) by method of stir casting. This technique is less expensive and very effective. The Hardness test and Wear test were performed on the specimens which are prepared by stir casting techniques. The result reveals that the addition of silicon carbide and alumina particles in aluminium matrix improves the mechanical properties.

  13. Recovery of the actinides by electrochemical methods in molten chlorides using solid aluminium cathode

    SciTech Connect

    Malmbeck, R.; Mendes, E.; Serp, J.; Soucek, P.; Glatz, J.P.; Cassayre, L.

    2007-07-01

    An electrorefining process in molten chloride salts is being developed at ITU to reprocess the spent nuclear fuel. According to the thermochemical properties of the system, aluminium is the most promising electrode material for the separation of actinides (An) from lanthanides (Ln). The actinides are selectively reduced from the fission products and stabilized by the formation of solid and compact actinide-aluminium alloys with the reactive cathode material. In this work, the maximum loading of aluminium with actinides was investigated by potentiostatic and galvano-static electrorefining of U-Pu- Zr alloys. A very high aluminium capacity was achieved, as the average loading was 1.6 g of U and Pu into 1 g of aluminium and the maximum achieved loading was 2.3 g. For recovery of the actinides from aluminium, a process based on chlorination and a subsequent sublimation of AlCl{sub 3} is proposed. (authors)

  14. Oxide film on 5052 aluminium alloy: Its structure and removal mechanism by activated CsF-AlF3 flux in brazing

    NASA Astrophysics Data System (ADS)

    Xiao, Bing; Wang, Dongpo; Cheng, Fangjie; Wang, Ying

    2015-05-01

    The oxide-film structure on the 5052 Al alloy and the film-removal mechanism by activated CsF-AlF3 flux in brazing were studied. Characterisation of the oxide film shows that thermally activated Mg, segregated from the alloy's interior, was significantly enriched and oxidised during medium-temperature brazing. Thus, the outer oxide surface consisted of the amorphous MgO-like phase, and the interior of the oxide film comprised mainly the amorphous MgO-like phase and dispersely distributed and less-ordered MgAl2O4. The MgO-like phase was the main obstacle to oxide removal in brazing. The activated ZnCl2-containing CsF-AlF3 flux effectively removed the oxide film, and the 5052 Al alloy was successfully brazed by the Zn-Al filler metal and activated flux. When Zn2+ in the molten flux permeated the oxide film through cracks, its chemical reaction with the Al substrate loosened the oxide film, which was eventually pushed out as the filler metal spread over the alloy surface.

  15. Experimental comparison of the MIG, friction stir welding, cold metal transfer and hybrid laser-MIG processes for AA 6005-T6 aluminium alloy

    NASA Astrophysics Data System (ADS)

    Caruso, Serafino; Sgambitterra, Emanuele; Rinaldi, Sergio; Gallone, Antonello; Viscido, Lucio; Filice, Luigino; Umbrello, Domenico

    2016-10-01

    In this study, the mechanical properties of welded joints of AA 6005-T6 aluminum alloy obtained with hybrid laser-MIG and cold metal transfer (CMT) welding were analyzed. The performance of hybrid laser-MIG and CMT welded joints were identified using tensile, bending, shear and fatigue life tests. Taking into account the process conditions and requirements, hybrid laser-MIG and CMT welding processes were compared with friction stir welding (FSW) and conventional metal inert gas (MIG) welding processes, shown in a previous work, to understand the advantages and disadvantages of the processes for welding applications of studied Al alloy. Better tensile, bending and shear strength and fatigue life behavior were obtained with hybrid laser-MIG and FSW welded joints compared with conventional MIG processes.

  16. Investigation of surface roughness and tool wear length with varying combination of depth of cut and feed rate of Aluminium alloy and P20 steel machining.

    NASA Astrophysics Data System (ADS)

    Varmma a/l Suparmaniam, Madan; Razlan Yusoff, Ahmad

    2016-02-01

    High-speed milling technique is often used in many industries to boost productivity of the manufacturing of high-technology components. The occurrence of wear highly limits the efficiency and accuracy of high- speed milling operations. In this paper, analysis of high-speed milling process parameters such as material removal rate, cutting speed, feed rate and depth of cut carried out by implemented to conventional milling. This experiment investigate the effects of varying combination of depth of cut and feed rate to tool wear rate length using metallurgical microscope and surface roughness using portable surface roughness tester after end milling of Aluminium and P20 steel. Results showed that feed rate significantly influences the surface roughness value while depth of cut does not as the surface roughness value keep increasing with the increase of feed rate and decreasing depth of cut. Whereas, tool wear rate almost remain unchanged indicates that material removal rate strongly contribute the wear rate. It believe that with no significant tool wear rate the results of this experiment are useful by showing that HSM technique is possible to be applied in conventional machine with extra benefits of high productivity, eliminating semi-finishing operation and reducing tool load for finishing.

  17. The effect of MAO processing time on surface properties and low temperature infrared emissivity of ceramic coating on aluminium 6061 alloy

    NASA Astrophysics Data System (ADS)

    Al Bosta, Mohannad M. S.; Ma, Keng-Jeng; Chien, Hsi-Hsin

    2013-09-01

    MAO ceramic coatings were prepared on aluminium 6061 surfaces at different treating durations (10, 20, ... 60 min), using alkali silicate electrolyte and pulsed bipolar current mode. The surface microstructures and properties were studied using SEM, XRD, EDX and a surface roughness tester. Image-Pro Plus and MATCH! softwares were used to analyze SEM micrographs and XRD results, respectively. The infrared emissivities of the ceramic coatings were measured at the 70 °C using FTIR spectrometer. We found a linear correlation between the volcano-like area and the surface roughness. The compositions and phases were associated with the volcano-like population and area. The curve of IR spectral emissivity was influenced by surface roughness, γ-alumina, sillimanite and cristobalite phases. The emissivity was enhanced by the surface roughness in the ranges 4.0-9.6 μm and 10.5-14.8 μm. In the range 7.0-8.0 μm, α-alumina and sillimanite phases enhanced the emissivity, while the cristobalite has a negative impact to the emissivity. A negative contributions were found for α-alumina in the region 9.6-16.0 μm and for the surface thickness in the region 15.0-16.0 μm. Overall, the average of long wave infrared (LWIR) emissivity ranged from 87.05% to 91.65%.

  18. Diamond grooving of rapidly solidified optical aluminium

    NASA Astrophysics Data System (ADS)

    Abou-El-Hossein, Khaled; Hsu, Wei-Yao; Ghobashy, Sameh; Cheng, Yuan-Chieh; Mkoko, Zwelinzima

    2015-10-01

    Traditional optical aluminium grades such as Al 6061 are intensively used for making optical components for applications ranging from mould insert fabrication to laser machine making. However, because of their irregular microstructure and relative inhomogeneity of material properties at micro scale, traditional optical aluminium may exhibit some difficulties when ultra-high precision diamond turned. Inhomogeneity and micro-variation in the material properties combined with uneven and coarse microstructure may cause unacceptable surface finish and accelerated tool wear, especially in grooving operation when the diamond tool edge is fully immersed in the material surface. Recently, new grades of optical aluminium that are featured by their ultra-fine microstructure and improved material properties have been developed to overcome the problem of high tool wear rates. The new aluminium grades have been developed using rapid solidification process which results in extremely small grain sizes combined with improved mechanical properties. The current study is concerned with investigating the performance of single-point diamond turning when grooving two grades of rapidly solidified aluminium (RSA) grades: RSA905 which is a high-alloyed aluminium grade and RSA443 which has a high silicon content. In this study, two series of experiments employed to create radial microgrooves on the two RSA grades. The surface roughness obtained on the groove surface is measured when different combinations of cutting parameters are used. Cutting speed is varied while feed rate and depth of cut were kept constant. The results show that groove surface roughness produced on RSA443 is higher than that obtained on RSA905. Also, the paper reports on the effect of cutting speed on surface roughness for each RSA grade.

  19. Volatilisation and oxidation of aluminium scraps fed into incineration furnaces

    SciTech Connect

    Biganzoli, Laura; Gorla, Leopoldo; Nessi, Simone; Grosso, Mario

    2012-12-15

    Highlights: Black-Right-Pointing-Pointer Aluminium packaging partitioning in MSW incineration residues is evaluated. Black-Right-Pointing-Pointer The amount of aluminium packaging recoverable from the bottom ashes is evaluated. Black-Right-Pointing-Pointer Aluminium packaging oxidation rate in the residues of MSW incineration is evaluated. Black-Right-Pointing-Pointer 80% of aluminium cans, 51% of trays and 27% of foils can be recovered from bottom ashes. - Abstract: Ferrous and non-ferrous metal scraps are increasingly recovered from municipal solid waste incineration bottom ash and used in the production of secondary steel and aluminium. However, during the incineration process, metal scraps contained in the waste undergo volatilisation and oxidation processes, which determine a loss of their recoverable mass. The present paper evaluates the behaviour of different types of aluminium packaging materials in a full-scale waste to energy plant during standard operation. Their partitioning and oxidation level in the residues of the incineration process are evaluated, together with the amount of potentially recoverable aluminium. About 80% of post-consumer cans, 51% of trays and 27% of foils can be recovered through an advanced treatment of bottom ash combined with a melting process in the saline furnace for the production of secondary aluminium. The residual amount of aluminium concentrates in the fly ash or in the fine fraction of the bottom ash and its recovery is virtually impossible using the current eddy current separation technology. The average oxidation levels of the aluminium in the residues of the incineration process is equal to 9.2% for cans, 17.4% for trays and 58.8% for foils. The differences between the tested packaging materials are related to their thickness, mechanical strength and to the alloy.

  20. On the effect of silicon and phosphorus during the precipitation of kappa-carbide in Iron-Manganese-Aluminium-Carbon alloys

    NASA Astrophysics Data System (ADS)

    Bartlett, Laura Nicole

    Implementation of lightweight high manganese and aluminum steels for use in high energy absorbing applications requires a detailed knowledge of how alloying additions and impurities affect age hardening and high strain rate fracture properties. Dynamic fracture toughness is an important design criterion but has not been reported previously in these alloys. In addition, previous studies have shown that silicon and phosphorus increased the strength and aged hardness; however, the mechanism was unknown. This research mainly focuses on the effect of silicon and phosphorus on the precipitation of kappa-carbide and alloy partitioning during aging. Short range ordering, SRO, of Fe-Al-C into relative atomic positions described by the E21 superlattice structure preceded and occurred concurrent to spinodal decomposition. Short range diffusion of phosphorus increased the kinetics of ordering resulting in a decrease in the time required for subsequent spinodal decomposition and an increase the amplitude of carbon concentration with time. Silicon increased the strength and hardness as a result of increased carbon partitioning into the kappa-carbide during aging. Dynamic fracture toughness was found to depend upon aluminum and carbon. Increasing the amount of solid solution carbon increased the dynamic fracture toughness in solution treated specimens. However, increasing carbon in aged specimens increased the amount of kappa-carbide and produced brittle fracture. Additions of aluminum from three to nine weight percent decreased toughness regardless of the heat treatment. Dynamic fracture toughness was a strong function of AlN content. A good combination of high strength and dynamic toughness with a corresponding density reduction of 10 to 12% is obtained with aluminum additions between 6 and 7% and carbon below 1.2%.

  1. The effect orientation of features in reconstructed atom probe data on the resolution and measured composition of T1 plates in an A2198 aluminium alloy.

    PubMed

    Mullin, Maria A; Araullo-Peters, Vicente J; Gault, Baptiste; Cairney, Julie M

    2015-12-01

    Artefacts in atom probe tomography can impact the compositional analysis of microstructure in atom probe studies. To determine the integrity of information obtained, it is essential to understand how the positioning of features influences compositional analysis. By investigating the influence of feature orientation within atom probe data on measured composition in microstructural features within an AA2198 Al alloy, this study shows differences in the composition of T1 (Al2CuLi) plates that indicates imperfections in atom probe reconstructions. The data fits a model of an exponentially-modified Gaussian that scales with the difference in evaporation field between solutes and matrix. This information provides a guide for obtaining the most accurate information possible.

  2. Launcher Roadmap for the CrVI Substitution of Surface Treatments. Screening of Trivalent-Chromium Conversion Solutions and First Promising Results for Repair Applications on Aluminium Alloys

    NASA Astrophysics Data System (ADS)

    Debout, Vincent; Pettier, Sophie

    2014-06-01

    Airbus Defence and Space, Space System is involved in a global roadmap for launchers in order to substitute hexavalent chromium (CrVI) and Cadmium in the current surface treatments on metallic structures.Within this framework, a screening of trivalent chromium (CrIII) conversion solutions for touch-up applications has been carried out since this step is crucial to perform local application or to repair minor damages on launcher structures but it leads to higher risks of exposure for the workers.Three commercial CrIII conversion solutions have been evaluated on high performance aluminum alloys such as AA2024 T3 and AA7175 T7351 that are often used as structural materials.This preliminary investigation highlights the effect of surface preparation, rinsing and conversion process on the final corrosion performance of conversion coatings (CCs). The results are also discussed in terms of visual aspect and adhesion with new Cr-free primers.Two operating sets of parameters are identified with promising results that represent the first steps towards the development of a new Cr-free touch-up process.

  3. Corrosion protection of Al alloys and Al-based metal-matrix composites by chemical passivation

    SciTech Connect

    Mansfeld, F.; Lin, S.; Sim, S.; Shih, H.

    1989-08-01

    Chemical passivation by immersion of aluminium alloys and aluminium 6061/ silicon carbide and aluminium 6061/graphite metal-matrix composites in cerium chloride solution produces very corrosion-resistant surfaces. Aluminium 6061 and aluminium 7075-T6 that had been immersed in 1000 ppm cerium chloride for one week did not suffer from pitting corrosion during immersion in acerated 0.5 N NaCl for three weeks. For aluminium 7075-T7l3 some improvement of the corrosion resistance was also achieved, but to a much lesser extent. Chemical passivation in cerium chloride was also successful for aluminium/silicon carbide and Allgraphite.

  4. Study on aluminium-based single films.

    PubMed

    Vinod Kumar, G S; García-Moreno, F; Babcsán, N; Brothers, A H; Murty, B S; Banhart, J

    2007-12-28

    In the present paper the authors studied isolated metallic films made from the same material used for making metallic foams, and then characterised their properties. Metal films were made from a liquid aluminium alloy reinforced with ceramic particles of known concentration. Melts without such particles were also investigated. It is shown that stable films could not be made from Al-Si alloy having no particles, and just extremely thin and fragile films could be made from commercially-pure Al. In contrast, aluminium alloys containing particles such as SiC and TiB(2) allowed pulling thin, stable films, which did not rupture. Significant thinning of films was observed when the particle concentration in the melt decreased. By in situ X-ray monitoring of liquid films during pulling, film thickness and drainage effects within the liquid film could be studied. The morphology and microstructure of films was characterised after solidification. Our work shows that the question of how foams are stabilised can be studied using a simplified system such as a film, instead of having to deal with the multitude of different structural elements present in a foam.

  5. Volatilisation and oxidation of aluminium scraps fed into incineration furnaces.

    PubMed

    Biganzoli, Laura; Gorla, Leopoldo; Nessi, Simone; Grosso, Mario

    2012-12-01

    Ferrous and non-ferrous metal scraps are increasingly recovered from municipal solid waste incineration bottom ash and used in the production of secondary steel and aluminium. However, during the incineration process, metal scraps contained in the waste undergo volatilisation and oxidation processes, which determine a loss of their recoverable mass. The present paper evaluates the behaviour of different types of aluminium packaging materials in a full-scale waste to energy plant during standard operation. Their partitioning and oxidation level in the residues of the incineration process are evaluated, together with the amount of potentially recoverable aluminium. About 80% of post-consumer cans, 51% of trays and 27% of foils can be recovered through an advanced treatment of bottom ash combined with a melting process in the saline furnace for the production of secondary aluminium. The residual amount of aluminium concentrates in the fly ash or in the fine fraction of the bottom ash and its recovery is virtually impossible using the current eddy current separation technology. The average oxidation levels of the aluminium in the residues of the incineration process is equal to 9.2% for cans, 17.4% for trays and 58.8% for foils. The differences between the tested packaging materials are related to their thickness, mechanical strength and to the alloy.

  6. Buckling tests of aluminium columns at elevated temperatures

    SciTech Connect

    Langhelle, N.K.; Amdahl, J.; Eberg, E.; Lundberg, S.

    1996-12-31

    Accidental fires are events with severe catastrophe potential for all offshore structures, and in particular for aluminium structures. Due to aluminium`s rapid strength degradation at elevated temperatures, this is particular true for aluminium structures. Accurate prediction of fire resistance is therefore essential. Experimental tests are needed to evaluate current design rules and state-of-the-art material models for aluminium under elevated temperatures. An experimental investigation was undertaken in order to study the behavior of AA 6082 alloy aluminium columns at elevated temperatures. Some of the tests were carried out at constant load with increasing temperature. Other tests experienced constant temperature and increasing load. Buckling tests at ambient temperature were also conducted. Particular emphasis was put on high temperature creep effects. The purpose of the tests was to provide data for verification of the material model implemented in the computer program USFOS, for analysis of progressive collapse analyses of space frame structures. The performance of the tempers T4 and T6 as well as columns with transversal welds are compared internally as well as to column buckling curves given in current design codes.

  7. Fatal aluminium phosphide poisoning

    PubMed Central

    Mittal, Sachin; Rani, Yashoda

    2015-01-01

    Aluminium phosphide (AlP) is a cheap solid fumigant and a highly toxic pesticide which is commonly used for grain preservation. AlP has currently aroused interest with a rising number of cases in the past four decades due to increased use for agricultural and non-agricultural purposes. Its easy availability in the markets has increased also its misuse for committing suicide. Phosphine inhibits cellular oxygen utilization and can induce lipid peroxidation. Poisoning with AlP has often occurred in attempts to commit suicide, and that more often in adults than in teenagers. This is a case of suicidal consumption of aluminium phosphide by a 32-year-old young medical anesthetist. Toxicological analyses detected aluminium phosphide. We believe that free access of celphos tablets in grain markets should be prohibited by law. PMID:27486362

  8. Tribological properties of aluminium-based materials

    NASA Astrophysics Data System (ADS)

    Iglesias Victoria, Patricia

    In order to improve the tribological performance of the aluminium-steel contact, two research lines have been followed: (1) Use of the ordered fluids liquid crystals and ionic liquids as lubricant additives. (2) Tribological behaviour of new powder metallurgy aluminium materials processed by mechanical milling. A parafinic-naftenic base oil modified by a 1wt% of four additives has been used: Three liquid crystals with increasing polarity: 4,4' -dibutylazobenzene (LC1) < colesteryl linoleate (LC2) < n-dodecyl ammonium chloride (LC3), and the ionic liquid 1-ethyl, 3-methyl-imidazolonium tetrafluoroborate. This is the first time that a ionic liquid is studied as lubricant additive. Viscosity measurements at 25 and 100°C, maximum number of molecules by unit aluminium surface and comparative costs of the additives showed the advantage of the ionic additives over the neutral ones. Pin-on-disk tests were performed according to ASTM G99. Influence of load, speed and temperature on friction and wear was studied for each additive. While the ionic liquid gives low friction (<0.1) and wear (≤10-5 mm3m-1), the performance of the liquid crystalline additives depends on the conditions. LC3 shows a higher lubricating ability than the neutral LC1 and LC2 under high load, speed or temperature. Only the ionic liquid shows tribochemical interaction (by SEM and EDS) with the steel and aluminium surfaces, with an increment in the fluorine content inside the wear track. The second line was to study the influence of the process conditions on the dry and lubricated wear of new powder-metallurgy aluminium materials. MA Al-NH3 milled under NH3 atmosphere was compared with (MA Al-Air) processed in air and with Al-1 which has not been mechanically alloyed. Conditions for mild to severe wear transition have been established. Al-1 is always under a severe wear regime. MA Al-NH3 shows transition to severe wear at 150°C, showing a 60% reduction in wear rate with respect to MA Al-Air and a two

  9. Time-resolved aluminium laser-induced plasma temperature measurements

    NASA Astrophysics Data System (ADS)

    Surmick, D. M.; Parigger, C. G.

    2014-11-01

    We seek to characterize the temperature decay of laser-induced plasma near the surface of an aluminium target from laser-induced breakdown spectroscopy measurements of aluminium alloy sample. Laser-induced plasma are initiated by tightly focussing 1064 nm, nanosecond pulsed Nd:YAG laser radiation. Temperatures are inferred from aluminium monoxide spectra viewed at systematically varied time delays by comparing experimental spectra to theoretical calculations with a Nelder Mead algorithm. The temperatures are found to decay from 5173 ± 270 to 3862 ± 46 Kelvin from 10 to 100 μs time delays following optical breakdown. The temperature profile along the plasma height is also inferred from spatially resolved spectral measurements and the electron number density is inferred from Stark broadened Hβ spectra.

  10. Interfacial morphology of low-voltage anodic aluminium oxide

    SciTech Connect

    Hu, Naiping; Dongcinn, Xuecheng; He, Xueying; Argekar, Sandip; Zhang, Yan; Browning, Jim; Schaefer, Dale

    2013-01-01

    X-ray reflectivity (XRR) and neutron reflectivity (NR), as well as ultra-smallangle X-ray scattering (USAXS), are used to examine the in-plane and surfacenormal structure of anodic films formed on aluminium alloy AA2024 and pure aluminium. Aluminium and alloy films up to 3500 A thick were deposited on Si wafers by electron beam evaporation of ingots. Porous anodic aluminium oxide (AAO) films are formed by polarizing at constant voltage up to 20 V noble to the open circuit potential. The voltage sweet spot (5 V) appropriate for constant-voltage anodization of such thin films was determined for both alloy and pure Al. In addition, a new concurrent voltage- and current-control protocol was developed to prepare films with larger pores (voltages higher than 5 V), but formed at a controlled current so that pore growth is slow enough to avoid stripping the aluminium substrate layer. USAXS shows that the pore size and interpore spacing are fixed in the first 10 s after initiation of anodization. Pores then grow linearly in time, at constant radius and interpore spacing. Using a combination of XRR and NR, the film density and degree of hydration of the films were determined from the ratio of scattering length densities. Assuming a chemical formula Al2O3xH2O, it was found that x varies from 0.29 for the native oxide to 1.29 for AAO grown at 20 V under concurrent voltage and current control. The average AAO film density of the porous film at the air surface is 2.45 (20) g cm3. The density of the barrier layer at the metal interface is 2.9 (4) g cm3, which indicates that this layer is also quite porous

  11. Aluminium and human breast diseases.

    PubMed

    Darbre, P D; Pugazhendhi, D; Mannello, F

    2011-11-01

    The human breast is exposed to aluminium from many sources including diet and personal care products, but dermal application of aluminium-based antiperspirant salts provides a local long-term source of exposure. Recent measurements have shown that aluminium is present in both tissue and fat of the human breast but at levels which vary both between breasts and between tissue samples from the same breast. We have recently found increased levels of aluminium in noninvasively collected nipple aspirate fluids taken from breast cancer patients (mean 268 ± 28 μg/l) compared with control healthy subjects (mean 131 ± 10 μg/l) providing evidence of raised aluminium levels in the breast microenvironment when cancer is present. The measurement of higher levels of aluminium in type I human breast cyst fluids (median 150 μg/l) compared with human serum (median 6 μg/l) or human milk (median 25 μg/l) warrants further investigation into any possible role of aluminium in development of this benign breast disease. Emerging evidence for aluminium in several breast structures now requires biomarkers of aluminium action in order to ascertain whether the presence of aluminium has any biological impact. To this end, we report raised levels of proteins that modulate iron homeostasis (ferritin, transferrin) in parallel with raised aluminium in nipple aspirate fluids in vivo, and we report overexpression of mRNA for several S100 calcium binding proteins following long-term exposure of MCF-7 human breast cancer cells in vitro to aluminium chlorhydrate.

  12. Corrosion of Aluminium Alloys by IRFNA

    DTIC Science & Technology

    1991-09-01

    250C). GA6 was electropolished and anodised. The electropolishing solution was a mixture of Na2CO3 (150g/dm- 3 ) and Na3PO4 (50g/dm-3 ) in deionised...established more rapidly. 2.2.6 Electropolished and Anodised Cell (GA6) Cell GA6 was electropolished in a Na2CO3/ Na3PO4 mixture (14V, 6Adm-2 , 800C

  13. Improved Durability Aluminium Alloys for Airframe Structures

    DTIC Science & Technology

    2000-04-01

    propagation. ,° " Sensitivity to IGC itself is a purely electrochemical C phenomenon (see e.g.1 ,2) determined by the existence of a " , microgalvanic...which is discussed later. S , Beside this main aspect of fatigue, it is necessary to assess the fatigue resistance of the bulk material1 1. Improved...Warner (1994) International patent Kc(MPa4m)* application WO 96/12829. T-L 100 / 150 90 / 130 8 Warner, T J ; Shahani, R A ; Lassince, P ; Raynaud , G M

  14. Hydrogenated vacancies lock dislocations in aluminium

    PubMed Central

    Xie, Degang; Li, Suzhi; Li, Meng; Wang, Zhangjie; Gumbsch, Peter; Sun, Jun; Ma, Evan; Li, Ju; Shan, Zhiwei

    2016-01-01

    Due to its high diffusivity, hydrogen is often considered a weak inhibitor or even a promoter of dislocation movements in metals and alloys. By quantitative mechanical tests in an environmental transmission electron microscope, here we demonstrate that after exposing aluminium to hydrogen, mobile dislocations can lose mobility, with activating stress more than doubled. On degassing, the locked dislocations can be reactivated under cyclic loading to move in a stick-slip manner. However, relocking the dislocations thereafter requires a surprisingly long waiting time of ∼103 s, much longer than that expected from hydrogen interstitial diffusion. Both the observed slow relocking and strong locking strength can be attributed to superabundant hydrogenated vacancies, verified by our atomistic calculations. Vacancies therefore could be a key plastic flow localization agent as well as damage agent in hydrogen environment. PMID:27808099

  15. Hydrogenated vacancies lock dislocations in aluminium

    NASA Astrophysics Data System (ADS)

    Xie, Degang; Li, Suzhi; Li, Meng; Wang, Zhangjie; Gumbsch, Peter; Sun, Jun; Ma, Evan; Li, Ju; Shan, Zhiwei

    2016-11-01

    Due to its high diffusivity, hydrogen is often considered a weak inhibitor or even a promoter of dislocation movements in metals and alloys. By quantitative mechanical tests in an environmental transmission electron microscope, here we demonstrate that after exposing aluminium to hydrogen, mobile dislocations can lose mobility, with activating stress more than doubled. On degassing, the locked dislocations can be reactivated under cyclic loading to move in a stick-slip manner. However, relocking the dislocations thereafter requires a surprisingly long waiting time of ~103 s, much longer than that expected from hydrogen interstitial diffusion. Both the observed slow relocking and strong locking strength can be attributed to superabundant hydrogenated vacancies, verified by our atomistic calculations. Vacancies therefore could be a key plastic flow localization agent as well as damage agent in hydrogen environment.

  16. Aluminium, antiperspirants and breast cancer.

    PubMed

    Darbre, P D

    2005-09-01

    Aluminium salts are used as the active antiperspirant agent in underarm cosmetics, but the effects of widespread, long term and increasing use remain unknown, especially in relation to the breast, which is a local area of application. Clinical studies showing a disproportionately high incidence of breast cancer in the upper outer quadrant of the breast together with reports of genomic instability in outer quadrants of the breast provide supporting evidence for a role for locally applied cosmetic chemicals in the development of breast cancer. Aluminium is known to have a genotoxic profile, capable of causing both DNA alterations and epigenetic effects, and this would be consistent with a potential role in breast cancer if such effects occurred in breast cells. Oestrogen is a well established influence in breast cancer and its action, dependent on intracellular receptors which function as ligand-activated zinc finger transcription factors, suggests one possible point of interference from aluminium. Results reported here demonstrate that aluminium in the form of aluminium chloride or aluminium chlorhydrate can interfere with the function of oestrogen receptors of MCF7 human breast cancer cells both in terms of ligand binding and in terms of oestrogen-regulated reporter gene expression. This adds aluminium to the increasing list of metals capable of interfering with oestrogen action and termed metalloestrogens. Further studies are now needed to identify the molecular basis of this action, the longer term effects of aluminium exposure and whether aluminium can cause aberrations to other signalling pathways in breast cells. Given the wide exposure of the human population to antiperspirants, it will be important to establish dermal absorption in the local area of the breast and whether long term low level absorption could play a role in the increasing incidence of breast cancer.

  17. The toxicity of aluminium in humans.

    PubMed

    Exley, C

    2016-06-01

    We are living in the 'aluminium age'. Human exposure to aluminium is inevitable and, perhaps, inestimable. Aluminium's free metal cation, Alaq(3+), is highly biologically reactive and biologically available aluminium is non-essential and essentially toxic. Biologically reactive aluminium is present throughout the human body and while, rarely, it can be acutely toxic, much less is understood about chronic aluminium intoxication. Herein the question is asked as to how to diagnose aluminium toxicity in an individual. While there are as yet, no unequivocal answers to this problem, there are procedures to follow to ascertain the nature of human exposure to aluminium. It is also important to recognise critical factors in exposure regimes and specifically that not all forms of aluminium are toxicologically equivalent and not all routes of exposure are equivalent in their delivery of aluminium to target sites. To ascertain if Alzheimer's disease is a symptom of chronic aluminium intoxication over decades or breast cancer is aggravated by the topical application of an aluminium salt or if autism could result from an immune cascade initiated by an aluminium adjuvant requires that each of these is considered independently and in the light of the most up to date scientific evidence. The aluminium age has taught us that there are no inevitabilities where chronic aluminium toxicity is concerned though there are clear possibilities and these require proving or discounting but not simply ignored.

  18. Reactive ion beam figuring of optical aluminium surfaces

    NASA Astrophysics Data System (ADS)

    Bauer, Jens; Frost, Frank; Arnold, Thomas

    2017-03-01

    Ultra-smooth and arbitrarily shaped reflective optics are necessary for further progress in EUV/XUV lithography, x-ray and synchrotron technology. As one of the most important technological mirror optic materials, aluminium behaves in a rather difficult way in ultra-precision machining with such standard techniques as diamond-turning and subsequent ion beam figuring (IBF). In particular, in the latter, a strong surface roughening is obtained. Hence, up to now it has not been possible to attain the surface qualities required for UV or just visible spectral range applications. To overcome the limitations mainly caused by the aluminium alloy structural and compositional conditions, a reactive ion beam machining process using oxygen process gas is evaluated. To clarify the principle differences in the effect of oxygen gas contrary to oxygen ions on aluminium surface machining, we firstly focus on chemical-assisted ion beam etching (CAIBE) and reactive ion beam etching (RIBE) experiments in a phenomenological manner. Then, the optimum process route will be explored within a more quantitative analysis applying the concept of power spectral density (PSD) for a sophisticated treatment of the surface topography. Eventually, the surface composition is examined by means of dynamic secondary ion mass spectrometry (SIMS) suggesting a characteristic model scheme for the chemical modification of the aluminium surface during oxygen ion beam machining. Monte Carlo simulations were applied to achieve a more detailed process conception.

  19. Microstructure, crystallographic texture and mechanical properties of friction stir welded AA2017A

    SciTech Connect

    Ahmed, M.M.Z.; Wynne, B.P.; Rainforth, W.M.; Threadgill, P.L.

    2012-02-15

    In this study a thick section (20 mm) friction stir welded AA2017A-T451 has been characterized in terms of microstructure, crystallographic texture and mechanical properties. For microstructural analysis both optical and scanning electron microscopes have been used. A detailed crystallographic texture analysis has been carried out using the electron back scattering diffraction technique. Crystallographic texture has been examined in both shoulder and probe affected regions of the weld NG. An entirely weak texture is observed at the shoulder affected region which is mainly explained by the effect of the sequential multi pass deformation experienced by both tool probe and tool shoulder. The texture in the probe dominated region at the AS side of the weld is relatively weak but still assembles the simple shear texture of FCC metals with B/B{sup Macron} and C components existing across the whole map. However, the texture is stronger at the RS than at the AS of the weld, mainly dominated byB/B{sup Macron} components and with C component almost absent across the map. An alternating bands between (B) components and (B{sup Macron }) component are observed only at the AS side of the weld. - Highlights: Black-Right-Pointing-Pointer Detailed investigation of microstructure and crystallographic texture. Black-Right-Pointing-Pointer The grain size is varied from the top to the bottom of the NG. Black-Right-Pointing-Pointer An entirely weak texture is observed at the shoulder affected region. Black-Right-Pointing-Pointer The texture in the probe affected region is dominated by simple shear texture.

  20. A 3D printed superconducting aluminium microwave cavity

    NASA Astrophysics Data System (ADS)

    Creedon, Daniel L.; Goryachev, Maxim; Kostylev, Nikita; Sercombe, Timothy B.; Tobar, Michael E.

    2016-07-01

    3D printing of plastics, ceramics, and metals has existed for several decades and has revolutionized many areas of manufacturing and science. Printing of metals, in particular, has found a number of applications in fields as diverse as customized medical implants, jet engine bearings, and rapid prototyping in the automotive industry. Although many techniques are used for 3D printing metals, they commonly rely on computer controlled melting or sintering of a metal alloy powder using a laser or electron beam. The mechanical properties of parts produced in such a way have been well studied, but little attention has been paid to their electrical properties. Here we show that a microwave cavity (resonant frequencies 9.9 and 11.2 GHz) 3D printed using an Al-12Si alloy exhibits superconductivity when cooled below the critical temperature of aluminium (1.2 K), with a performance comparable with the common 6061 alloy of aluminium. Superconducting cavities find application in numerous areas of physics, from particle accelerators to cavity quantum electrodynamics experiments. The result is achieved even with a very large concentration of non-superconducting silicon in the alloy of 12.18%, compared with Al-6061, which has between 0.4% and 0.8%. Our results may pave the way for the possibility of 3D printing superconducting cavity configurations that are otherwise impossible to machine.

  1. Dependence in Classification of Aluminium Waste

    NASA Astrophysics Data System (ADS)

    Resti, Y.

    2015-06-01

    Based on the dependence between edge and colour intensity of aluminium waste image, the aim of this paper is to classify the aluminium waste into three types; pure aluminium, not pure aluminium type-1 (mixed iron/lead) and not pure aluminium type 2 (unrecycle). Principal Component Analysis (PCA) was employed to reduction the dimension of image data, while Bayes’ theorem with the Gaussian copula was applied to classification. The copula was employed to handle dependence between edge and colour intensity of aluminium waste image. The results showed that the classifier has been correctly classifiable by 88.33%.

  2. Aluminium surface treatment with ceramic phases using diode laser

    NASA Astrophysics Data System (ADS)

    Labisz, K.; Tański, T.; Brytan, Z.; Pakieła, W.; Wiśniowski, M.

    2016-07-01

    Ceramic particles powder feeding into surface layer of engineering metal alloy is a well-known and widely used technique. New approach into the topic is to obtain finely distributed nano-sized particles involved in the aluminium matrix using the traditional laser technology. In this paper are presented results of microstructure investigation of cast aluminium-silicon-copper alloys surface layer after heat treatment and alloying with ceramic carbides of WC and ZrO2 using high-power diode laser. The surface layer was specially prepared for the reason of reducing the reflectivity, which is the main problem in the up-to-date metal matrix composites production. With scanning electron microscopy, it was possible to determine the deformation process and distribution of WC and ZrO2 ceramic powder phase. Structure of the surface after laser treatment changes, revealing three zones—remelting zone, heat-affected zone and transition zone placed over the Al substrate. The structural changes of ceramic powder, its distribution and morphology as well as microstructure of the matrix material influence on functional properties, especially wear resistance and hardness of the achieved layer, were investigated.

  3. Consolidation of copper and aluminium powders by spark plasma sintering

    NASA Astrophysics Data System (ADS)

    Saiprasad, M.; Atchayakumar, R.; Thiruppathi, K.; Raghuraman, S.

    2016-09-01

    Processing in the powder metallurgy route has emerged as an economical process for the production of near net shaped components with a wide range of desired mechanical properties suitable for various applications of industrial needs. This research work was conducted with an objective of studying the improvisation of density and hardness of Copper-Aluminium alloy prepared by spark plasma sintering. Cu-Al alloy with a composition of 95% copper and 5% aluminium was prepared by SPS process. SPS is a low voltage, DC pulse current activated, pressure-assisted sintering, which enables sintering at lower temperatures and shorter durations. The combination offered by Cu-Al alloy of high strength and high corrosion resistance results their applications under a wide variety of conditions. The density and hardness of the prepared sample were measured by conducting appropriate tests. Apparently, the values of hardness and density of the specimen prepared by SPS seemed to be better than that of conventional sintering. The experimental procedure, testing methodologies and analysis are presented.

  4. Aluminium phosphide-induced leukopenia

    PubMed Central

    Ntelios, Dimitrios; Mandros, Charalampos; Potolidis, Evangelos; Fanourgiakis, Panagiotis

    2013-01-01

    Acute intoxication from the pesticide aluminium phosphide is a relatively rare, life-threatening condition in which cardiovascular decompensation is the most feared problem. We report the case of a patient exposed to aluminium phosphide-liberated phosphine gas. It resulted in the development of a gastroenteritis-like syndrome accompanied by severe reduction in white blood cell numbers as an early and prominent manifestation. By affecting important physiological processes such as mitochondrial function and reactive oxygen species homeostasis, phosphine could cause severe toxicity. After presenting the characteristics of certain leucocyte subpopulations we provide the current molecular understanding of the observed leukopenia which in part seems paradoxical. PMID:24172776

  5. Synergistic effects of carboxymethyl cellulose and ZnO as alkaline electrolyte additives for aluminium anodes with a view towards Al-air batteries

    NASA Astrophysics Data System (ADS)

    Liu, Jie; Wang, Dapeng; Zhang, Daquan; Gao, Lixin; Lin, Tong

    2016-12-01

    The synergistic effects of carboxymethyl cellulose (CMC) and zinc oxide (ZnO) have been investigated as alkaline electrolyte additives for the AA5052 aluminium alloy anode in aluminium-air battery by the hydrogen evolution test, the electrochemical measurements and the surface analysis method. The combination of CMC and ZnO effectively retards the self-corrosion of AA5052 alloy in 4 M NaOH solution. A complex film is formed via the interaction between CMC and Zn2+ ions on the alloy surface. The carboxyl groups adsorbed on the surface of aluminium make the protective film more stable. The cathodic reaction process is mainly suppressed significantly. AA5052 alloy electrode has a good discharge performance in the applied electrolyte containing the composite CMC/ZnO additives.

  6. The prophylactic reduction of aluminium intake.

    PubMed

    Lione, A

    1983-02-01

    The use of modern analytical methods has demonstrated that aluminium salts can be absorbed from the gut and concentrated in various human tissues, including bone, the parathyroids and brain. The neurotoxicity of aluminium has been extensively characterized in rabbits and cats, and high concentrations of aluminium have been detected in the brain tissue of patients with Alzheimer's disease. Various reports have suggested that high aluminium intakes may be harmful to some patients with bone disease or renal impairment. Fatal aluminium-induced neuropathies have been reported in patients on renal dialysis. Since there are no demonstrable consequences of aluminium deprivation, the prophylactic reduction of aluminium intake by many patients would appear prudent. In this report, the major sources of aluminium in foods and non-prescription drugs are summarized and alternative products are described. The most common foods that contain substantial amounts of aluminium-containing additives include some processed cheeses, baking powders, cake mixes, frozen doughs, pancake mixes, self-raising flours and pickled vegetables. The aluminium-containing non-prescription drugs include some antacids, buffered aspirins, antidiarrhoeal products, douches and haemorrhoidal medications. The advisability of recommending a low aluminium diet for geriatric patients is discussed in detail.

  7. Occupational asthma caused by aluminium welding.

    PubMed

    Vandenplas, O; Delwiche, J P; Vanbilsen, M L; Joly, J; Roosels, D

    1998-05-01

    Work-related asthma has been documented in workers employed in the primary aluminium industry and in the production of aluminium salts. The role of aluminium in the development of occupational asthma has, however, never been convincingly substantiated. We investigated a subject who experienced asthmatic reactions related to manual metal arc welding on aluminium. Challenge exposure to aluminium welding with flux-coated electrodes, as well as with electrodes without flux, elicited marked asthmatic reactions. Manual metal arc welding on mild steel did not cause significant bronchial response. The results of inhalation challenges combined with exposure assessments provided evidence that aluminium can cause asthmatic reactions in the absence of fluorides. Awareness of this possibility may be relevant to the investigation of asthma in workers exposed to aluminium.

  8. Comparative study using MS and XRD of Fe80Al20 alloy produced by mechanical alloying

    NASA Astrophysics Data System (ADS)

    Hadef, F.; Otmani, A.; Grenèche, J. M.

    2013-08-01

    An X-ray diffraction and 57Fe Mössbauer effect study of mechanically alloyed Fe80Al20 is presented. X-ray measurements indicate that the disordered bcc α-Fe(Al) solid solution was formed after 2 h of milling, while the analysis of Mössbauer spectra suggested that total dissolution of aluminium is achieved after 10 h of milling. These differences can be attributed to: (i) rapid nanocrystallization of aluminium and/or (ii) small particles with small amounts of aluminium cannot be detected by the X-ray diffraction technique.

  9. Downscaled anodic oxidation process for aluminium in oxalic acid

    NASA Astrophysics Data System (ADS)

    Sieber, M.; Morgenstern, R.; Kuhn, D.; Hackert-Oschätzchen, M.; Schubert, A.; Lampke, T.

    2017-03-01

    The increasing multi-functionality of parts and assemblies in several fields of engineering demands, amongst others, highly functionalised surfaces. For the different applications, on the one hand, there is a need to scale up surface modification processes originating in the nano- and micro-scale. On the other hand, conventional macro-scale surface refinement methods offer a huge potential for application in the said nano- and micro-scale. The anodic oxidation process, which is established especially for aluminium and its alloys, allows the formation of oxide ceramic layers on the surface. The build-up of an oxide ceramic coating comes along with altered chemical, tribological and electrical surface properties. As a basis for further investigations regarding the use of the anodic oxidation process for micro-scale-manufacturing, the scale effects of oxalic acid anodising on commercially pure aluminium as well as on the AlZn5.5MgCu alloy are addressed in the present work. The focus is on the amount of oxide formed during a potentiostatic process in relation to the exchanged amount of charge. Further, the hardness of the coating as an integral measure to assess the porous oxide structure is approached by nano-indentation technique.

  10. Experimental study of friction in aluminium bolted joints

    NASA Astrophysics Data System (ADS)

    Croccolo, D.; de Agostinis, M.; Vincenzi, N.

    2010-06-01

    This study aims at developing an experimental tool useful to define accurately the friction coefficients in bolted joints and, therefore, at relating precisely the tightening torque to the bolt preloading force in some special components used in front motorbike suspensions. The components under investigation are some clamped joints made of aluminium alloy. The preloading force is achieved by applying a torque wrench to the bolt head. Some specific specimens have been appropriately designed and realized in order to study the tribological aspects of the tightening phase. Experimental tests have been performed by applying the Design of Experiment (DOE) method in order to obtain a mathematical model for the friction coefficients. Three replicas of a full factorial DOE at two levels for each variable have been carried out. The levels include cast versus forged aluminium alloy, anodized versus spray-painted surface, lubricated versus unlubricated screw, and first tightening (fresh unspoiled surfaces) versus sixth tightening (spoiled surfaces). The study considers M8x1.25 8.8 galvanized screws.

  11. Bumblebee Pupae Contain High Levels of Aluminium

    PubMed Central

    Exley, Christopher; Rotheray, Ellen; Goulson, David

    2015-01-01

    The causes of declines in bees and other pollinators remains an on-going debate. While recent attention has focussed upon pesticides, other environmental pollutants have largely been ignored. Aluminium is the most significant environmental contaminant of recent times and we speculated that it could be a factor in pollinator decline. Herein we have measured the content of aluminium in bumblebee pupae taken from naturally foraging colonies in the UK. Individual pupae were acid-digested in a microwave oven and their aluminium content determined using transversely heated graphite furnace atomic absorption spectrometry. Pupae were heavily contaminated with aluminium giving values between 13.4 and 193.4 μg/g dry wt. and a mean (SD) value of 51.0 (33.0) μg/g dry wt. for the 72 pupae tested. Mean aluminium content was shown to be a significant negative predictor of average pupal weight in colonies. While no other statistically significant relationships were found relating aluminium to bee or colony health, the actual content of aluminium in pupae are extremely high and demonstrate significant exposure to aluminium. Bees rely heavily on cognitive function and aluminium is a known neurotoxin with links, for example, to Alzheimer’s disease in humans. The significant contamination of bumblebee pupae by aluminium raises the intriguing spectre of cognitive dysfunction playing a role in their population decline. PMID:26042788

  12. Bumblebee pupae contain high levels of aluminium.

    PubMed

    Exley, Christopher; Rotheray, Ellen; Goulson, David

    2015-01-01

    The causes of declines in bees and other pollinators remains an on-going debate. While recent attention has focussed upon pesticides, other environmental pollutants have largely been ignored. Aluminium is the most significant environmental contaminant of recent times and we speculated that it could be a factor in pollinator decline. Herein we have measured the content of aluminium in bumblebee pupae taken from naturally foraging colonies in the UK. Individual pupae were acid-digested in a microwave oven and their aluminium content determined using transversely heated graphite furnace atomic absorption spectrometry. Pupae were heavily contaminated with aluminium giving values between 13.4 and 193.4 μg/g dry wt. and a mean (SD) value of 51.0 (33.0) μg/g dry wt. for the 72 pupae tested. Mean aluminium content was shown to be a significant negative predictor of average pupal weight in colonies. While no other statistically significant relationships were found relating aluminium to bee or colony health, the actual content of aluminium in pupae are extremely high and demonstrate significant exposure to aluminium. Bees rely heavily on cognitive function and aluminium is a known neurotoxin with links, for example, to Alzheimer's disease in humans. The significant contamination of bumblebee pupae by aluminium raises the intriguing spectre of cognitive dysfunction playing a role in their population decline.

  13. The study of aluminium anodes for high power density Al/air batteries with brine electrolytes

    NASA Astrophysics Data System (ADS)

    Nestoridi, Maria; Pletcher, Derek; Wood, Robert J. K.; Wang, Shuncai; Jones, Richard L.; Stokes, Keith R.; Wilcock, Ian

    Aluminium alloys containing small additions of both tin (∼0.1 wt%) and gallium (∼0.05 wt%) are shown to dissolve anodically at high rates in sodium chloride media at room temperatures; current densities >0.2 A cm -2 can be obtained at potentials close to the open circuit potential, ∼-1500 mV versus SCE. The tin exists in the alloys as a second phase, typically as ∼1 μm inclusions (precipitates) distributed throughout the aluminium structure, and anodic dissolution occurs to form pits around the tin inclusions. Although the distribution of the gallium in the alloy could not be established, it is also shown to be critical in the formation of these pits as well as maintaining their activity. The stability of the alloys to open circuit corrosion and the overpotential for high rate dissolution, both critical to battery performance, are shown to depend on factors in addition to elemental composition; both heat treatment and mechanical working influence the performance of the alloy. The correlation between alloy performance and their microstructure has been investigated.

  14. Localised anodic oxidation of aluminium material using a continuous electrolyte jet

    NASA Astrophysics Data System (ADS)

    Kuhn, D.; Martin, A.; Eckart, C.; Sieber, M.; Morgenstern, R.; Hackert-Oschätzchen, M.; Lampke, T.; Schubert, A.

    2017-03-01

    Anodic oxidation of aluminium and its alloys is often used as protection against material wearout and corrosion. Therefore, anodic oxidation of aluminium is applied to produce functional oxide layers. The structure and properties of the oxide layers can be influenced by various factors. These factors include for example the properties of the substrate material, like alloy elements and heat treatment or process parameters, like operating temperature, electric parameters or the type of the used electrolyte. In order to avoid damage to the work-piece surface caused by covering materials in masking applications, to minimize the use of resources and to modify the surface in a targeted manner, the anodic oxidation has to be localised to partial areas. Within this study a proper alternative without preparing the substrate by a mask is investigated for generating locally limited anodic oxidation by using a continuous electrolyte jet. Therefore aluminium material EN AW 7075 is machined by applying a continuous electrolyte jet of oxalic acid. Experiments were carried out by varying process parameters like voltage or processing time. The realised oxide spots on the aluminium surface were investigated by optical microscopy, SEM and EDX line scanning. Furthermore, the dependencies of the oxide layer properties from the process parameters are shown.

  15. Tensile and fatigue behaviour of self-piercing rivets of CFRP to aluminium for automotive application

    NASA Astrophysics Data System (ADS)

    Kang, J.; Rao, H.; Zhang, R.; Avery, K.; Su, X.

    2016-07-01

    In this study, the tensile and fatigue behaviour of self-piercing rivets (SPRs) in carbon fibre reinforced plastic (CFRP) to aluminium 6111 T82 alloys were evaluated. An average maximum lap-shear tensile load capacity of 3858 N was achieved, which is comparable to metal-to-metal SPR lap-shear joints. The CFRP-Al SPRs failed in lap-shear tension due to pull-out of the rivet head from the CFRP upper sheet. The CFRP-Al SPR lap- shear specimens exhibited superior fatigue life compared to previously studied aluminium-to- aluminium SPR lap-shear joints. The SPR lap-shear joints under fatigue loads failed predominantly due to kinked crack growth along the width of the bottom aluminium sheet. The fatigue cracks initiated in the plastically deformed region of the aluminium sheet close to the rivet shank in the rivet-sheet interlock region. Scatter in fatigue life and failure modes was observed in SPR lap-shear specimens tested close to maximum tensile load.

  16. Nano-crystalline P/M aluminium for automotive applications

    NASA Astrophysics Data System (ADS)

    Hummert, K.; Schattevoy, R.; Broda, M.; Knappe, M.; Beiss, P.; Klubberg, F.; Schubert, T. H.; Leuschner, R.

    2009-01-01

    The reduction of total vehicle weight and lowering of moving masses within the engine are key elements to overcome future emission challenges of the automotive industry. Within a German BMBF funded project the melt spinning technology will be driven to a series production status. The very fast cooling condition of the melt leads to a nano-structure of the aluminium material. This results in new material properties of known alloys. The strength increases dramatically without lowered forming behaviour. With this process the freedom of designing complex alloys is very flexible. Different alloys have been investigated for several applications, where high strength at room and elevated temperatures and/or high wear resistance is required. This paper presents some results regarding the processing, microstructure and mechanical properties of a developed Al-Ni-Fe alloy. This joined research project with partners from the automotive industry as well as automotive suppliers and universities is funded by the German BMBF "NanoMobile" Program under Project number 03X3008.

  17. A review of semi-solid aluminium-steel joining processes

    NASA Astrophysics Data System (ADS)

    Obeidi, Muhannad; McCarthy, Éanna; Brabazon, Dermot

    2016-10-01

    The semi-solid metal (SSM) forming process can be applied to achieve near net shape forming of metal alloys, and provides superior component properties compared to those achievable with conventional casting methods. The technique, also commonly called thixoforming, relies on achieving a spheroidal microstructure within the metal alloy so that its fluidity can be adjusted to achieve a controlled laminar filling of the die. Despite the better quality and the higher mechanical properties of an SSM product, thixoforming still represents only 1% of the total aluminium production, which can be explained by the higher premium cost of the processing equipment compared to conventional die casting. The method has also proven successful as a joining method, for joining similar and dissimilar materials. This paper reviews semisolid forming as a forming method and as a joining method, in particular the joining of dissimilar materials such as stainless steel to aluminium.

  18. Aluminium in foodstuffs and diets in Sweden.

    PubMed

    Jorhem, L; Haegglund, G

    1992-01-01

    The levels of aluminium have been determined in a number of individual foodstuffs on the Swedish market and in 24 h duplicate diets collected by women living in the Stockholm area. The results show that the levels in most foods are very low and that the level in vegetables can vary by a factor 10. Beverages from aluminium cans were found to have aluminium levels not markedly different from those in glass bottles. Based on the results of the analysis of individual foods, the average Swedish daily diet was calculated to contain about 0.6 mg aluminium, whereas the mean content of the collected duplicate diets was 13 mg. A cake made from a mix containing aluminium phosphate in the baking soda was identified as the most important contributor of aluminium to the duplicate diets. Tea and aluminium utensils were estimated to increase the aluminium content of the diets by approximately 4 and 2 mg/day, respectively. The results also indicate that a considerable amount of aluminium must be introduced from other sources.

  19. Effect of the layer of anodized 7075-T6 aluminium corrosion properties

    NASA Astrophysics Data System (ADS)

    Montoya Z, R. D.; L, E. Vera; Pineda T, Y.; Cedeño, M. L.

    2017-01-01

    Aluminium alloys are widely used in various sectors of industry. The 7075-T6 alloy corresponding to an Al-Zn T6, is mostly used as structural component in the aviation industry, due to the good relationship between weight and mechanical properties. However, the negative point of this alloys is the resistance to corrosion, which is why they need to be coated with an anodic film. Different surface treatments, such as anodizing, are used to improve corrosion resistance. Anodizing is an electrolytic process by which a protective layer on aluminium known as “alumina” is formed, this is formed by the passage of an electric current in an acidic electrolyte. This investigation presents a study of the effect of the thickness of layers of alumina deposited by anodized method, in the corrosion resistance of 7075-T6 aluminium. This study was performed by using in a solution of tartaric acid - sulfuric acid and an inorganic salt. To evaluate the influence alumina layer thickness on the corrosion properties some tests were carried out by using the electrochemical spectroscopy impedances (EIS) technique and Tafel polarization curves. It was found that the grown of the thickness of film favourably influences in the corrosion resistance.

  20. Enriched alloy layer on an Al-Cu alloy studied by cyclic voltammetry

    NASA Astrophysics Data System (ADS)

    García Vergara, S. J.; Blanco Pinzon, C. E.; Skeldon, P.

    2017-01-01

    The behaviour of enriched Al-0.7at.%Cu alloy is investigated using cyclic voltammetry. Enriched alloy layers at the interface between the alloy/oxide film were developed by alkaline etching at 5mAcm-2 in 0.1M sodium hydroxide solution at 298K, with the time of etching determining the extent of enrichment. Cyclic voltammograms were recorded at a scan rate of 10mV s-1 in naturally aerated 0.1M ammonium pentaborate solution at 298K. The current overshoot of the enriched alloys was different from that for non-enriched alloy. The latter material revealed the usual single peaks, which are very similar. In contrast, the overshoot comprised two or more components for the enriched alloys. The behaviour is suggested to be associated with the atomic bonding of aluminium in copper-rich and aluminium-rich regions of the enriched alloy layer, with influence on the activation potentials for oxidation of aluminium.

  1. Lactobacillus plantarum CCFM639 alleviates aluminium toxicity.

    PubMed

    Yu, Leilei; Zhai, Qixiao; Liu, Xiaoming; Wang, Gang; Zhang, Qiuxiang; Zhao, Jianxin; Narbad, Arjan; Zhang, Hao; Tian, Fengwei; Chen, Wei

    2016-02-01

    Aluminium (Al) is the most abundant metal in the earth's crust. Al exposure can cause a variety of adverse physiological effects in humans and animals. Our aim was to demonstrate that specific probiotic bacteria can play a special physiologically functional role in protection against Al toxicity in mice. Thirty strains of lactic acid bacteria (LAB) were tested for their aluminium-binding ability, aluminium tolerance, their antioxidative capacity, and their ability to survive the exposure to artificial gastrointestinal (GI) juices. Lactobacillus plantarum CCFM639 was selected for animal experiments because of its excellent performance in vitro. Forty mice were divided into four groups: control, Al only, Al plus CCFM639, and Al plus deferiprone (DFP). CCFM639 was administered at 10(9) CFU once daily for 10 days, followed by a single oral dose of aluminium chloride hexahydrate at 5.14 mg aluminium (LD50) for each mouse. The results showed that CCFM639 treatment led to a significant reduction in the mortality rates with corresponding decrease in intestinal aluminium absorption and in accumulation of aluminium in the tissues and amelioration of hepatic histopathological damage. This probiotic treatment also resulted in alleviation of hepatic, renal, and cerebral oxidative stress. The treatment of L. plantarum CCFM639 has potential as a therapeutic dietary strategy against acute aluminium toxicity.

  2. High aluminium content of infant milk formulas.

    PubMed Central

    Weintraub, R; Hams, G; Meerkin, M; Rosenberg, A R

    1986-01-01

    The aluminium content of several commercially available infant milk formulas was measured by electrothermal atomic absorption spectrometry. Results were compared with those for fresh breast milk, cow's milk, and local tap water. Differences in aluminium concentration of greater than 150-fold were found, with the lowest concentrations in breast milk. PMID:3767424

  3. A Study on 3-Body Abrasive Wear Behaviour of Aluminium 8011 / Graphite Metal Matrix Composite

    NASA Astrophysics Data System (ADS)

    Latha Shankar, B.; Anil, K. C.; Patil, Rahul

    2016-09-01

    Metals and alloys have found their vital role in many applications like structural, corrosive, tribological, etc., in engineering environment. The alloys/composites having high strength to low weight ratio have gained attention of many researchers recently. In this work, graphite reinforced Aluminium 8011 metal matrix composite was prepared by conventional stir casting route, by varying the weight % of reinforcement. Uniform distribution of Graphite in matrix alloy was confirmed by optical micrographs. Prepared composite specimens were subjected to 3-body abrasive testing by varying applied load and time, the silica particles of 400 grit size were used as abrasive particles. It was observed that with the increase of weight% of Graphite the wear resistance of composite was also increasing and on comparison it was found that reinforced composite gives good wear resistance than base alloy.

  4. Aluminium Diphosphamethanides: Hidden Frustrated Lewis Pairs.

    PubMed

    Styra, Steffen; Radius, Michael; Moos, Eric; Bihlmeier, Angela; Breher, Frank

    2016-07-04

    The synthesis and characterisation of two aluminium diphosphamethanide complexes, [Al(tBu)2 {κ(2) P,P'-Mes*PCHPMes*}] (3) and [Al(C6 F5 )2 {κ(2) P,P'-Mes*PCHPMes*}] (4), and the silylated analogue, Mes*PCHP(SiMe3 )Mes* (5), are reported. The aluminium complexes feature four-membered PCPAl core structures consisting of diphosphaallyl ligands. The silylated phosphine 5 was found to be a valuable precursor for the synthesis of 4 as it cleanly reacts with the diaryl aluminium chloride [(C6 F5 )2 AlCl]2 . The aluminium complex 3 reacts with molecular dihydrogen at room temperature under formation of the acyclic σ(2) λ(3) ,σ(3) λ(3) -diphosphine Mes*PCHP(H)Mes* and the corresponding dialkyl aluminium hydride [tBu2 AlH]3 . Thus, 3 belongs to the family of so-called hidden frustrated Lewis pairs.

  5. Intestinal absorption of aluminium in renal failure.

    PubMed

    Drüeke, Tilman B

    2002-01-01

    The proportion of the daily ingested aluminium that is absorbed in the intestinal tract has remained a matter of debate for many years because no reliable method of measurement was available. Studies with earlier analytic techniques reported fractional absorption of aluminium from as little as 0.001% to as much as 27% of an oral dose. Measurement of (26)Al by high-energy accelerator mass spectrometry has permitted more accurate analyses. In normal young rats, 0.05-0.1% of ingested aluminium is absorbed in the intestine, of which roughly half goes to the skeleton within 2 h, whereas the remaining half is excreted in the urine, most of it within 48 h. Deposition in organs other than the skeleton appears to be negligible. In healthy human volunteers, the most recent estimates of fractional intestinal (26)Al absorption were also in the range of 0.06-0.1%. In both rats and humans, intestinal absorption of aluminium is subject to many systemic and local factors. The latter include various compounds with which aluminium is complexed in the gut lumen, and gastric acidity. The influence of food is controversial; however, absorption appears higher in the fasted than the post-prandial state. Luminal phosphate concentration decreases aluminium absorption, whereas citrate increases it. For theoretical reasons, silicates should prevent aluminium absorption, but experimental evidence has not supported this theory. Whether water hardness affects aluminium bioavailability remains a matter of debate. General conditions may also modify aluminium absorption and deposition in bone. Examples of these general factors include the uraemic syndrome, diabetes mellitus, secondary hyperparathyroidism, vitamin D status, Alzheimer's disease and Down's syndrome. Awareness of intestinal absorption of aluminium is particularly important, given that aluminium-based binders continue to be used in uraemic patients, despite the hazards of aluminium accumulation. The lessons we have learned about

  6. New metallic alloys incorporating fullerenes and carbon nanotubes

    NASA Astrophysics Data System (ADS)

    Doome, R. J.; Fonseca, A.; Nagy, J. B.

    1998-08-01

    In order to open new routes to fullerenes application, we have investigated the effect of fullerenes and nanotubes in metallic alloys. Fullerenes mixture and carbon nanotubes have been used as new carbon sources in the synthesis of metallic alloys (Al, Fe and Ni). After melting under inert atmosphere, macroscopic homogeneous alloys were obtained with iron and nickel but the aluminium based alloys looked rather inhomogeneous due to an incomplete melting. From the samples analysis by chemical reactions and XPS, it was concluded that the carbon is essentially located on the alloy surface as carbide and sp2 structures. Except for the aluminium based alloy where some fullerenes were still detected, thermal treatment as well as metal catalytic effect led to the decomposition of the fullerenes in the alloys. Nevertheless, carbon nanotubes kept their structure and were trapped in the alloys. The hardness of these new alloys were determined and compared to values of common alloys incorporating graphite and norit-A as carbon sources. The preliminary results showed slightly higher hardness values for alloys incorporating fullerenes and weaker values for alloys incorporating carbon nanotubes.

  7. Abrasive wear of alumina fibre-reinforced aluminium

    NASA Astrophysics Data System (ADS)

    Axen, N.; Alahelisten, A.; Jacobson, S.

    1994-04-01

    The friction and abrasive wear behaviour of an Al-Si1MgMn aluminium alloy reinforced with 10, 15 and 30 vol.% of alumina fibers has been evaluated. The influence of fiber content, matrix hardness, applied load as well as the hardness and size of the abrasive grits was investigated. The tests were performed with a pin-on-drum two-body abrasion apparatus. The wear mechanisms were studied using scanning electron microscopy. It is shown that fiber reinforcement increases the wear resistance in milder abrasive situations, i.e. small and soft abrasives and low loads. However, in tougher abrasive situations, meaning coarse and hard abrasives and high loads, the wear resistance of the composites is equal to or, in some cases, even lower than that of the unreinforced material. It is also shown that the coefficient of friction decreases with increasing fiber content and matrix hardness of the composites.

  8. Process Simulation of Aluminium Sheet Metal Deep Drawing at Elevated Temperatures

    SciTech Connect

    Winklhofer, Johannes; Trattnig, Gernot; Sommitsch, Christof

    2010-06-15

    Lightweight design is essential for an economic and environmentally friendly vehicle. Aluminium sheet metal is well known for its ability to improve the strength to weight ratio of lightweight structures. One disadvantage of aluminium is that it is less formable than steel. Therefore complex part geometries can only be realized by expensive multi-step production processes. One method for overcoming this disadvantage is deep drawing at elevated temperatures. In this way the formability of aluminium sheet metal can be improved significantly, and the number of necessary production steps can thereby be reduced. This paper introduces deep drawing of aluminium sheet metal at elevated temperatures, a corresponding simulation method, a characteristic process and its optimization. The temperature and strain rate dependent material properties of a 5xxx series alloy and their modelling are discussed. A three dimensional thermomechanically coupled finite element deep drawing simulation model and its validation are presented. Based on the validated simulation model an optimised process strategy regarding formability, time and cost is introduced.

  9. Aspects of ultra-high-precision diamond machining of RSA 443 optical aluminium

    NASA Astrophysics Data System (ADS)

    Mkoko, Z.; Abou-El-Hossein, K.

    2015-08-01

    Optical aluminium alloys such as 6061-T6 are traditionally used in ultra-high precision manufacturing for making optical mirrors for aerospace and other applications. However, the optics industry has recently witnessed the development of more advanced optical aluminium grades that are capable of addressing some of the issues encountered when turning with single-point natural monocrystalline diamond cutters. The advent of rapidly solidified aluminium (RSA) grades has generally opened up new possibilities for ultra-high precision manufacturing of optical components. In this study, experiments were conducted with single-point diamond cutters on rapidly solidified aluminium RSA 443 material. The objective of this study is to observe the effects of depth of cut and feed rate at a fixed rotational speed on the tool wear rate and resulting surface roughness of diamond turned specimens. This is done to gain further understanding of the rate of wear on the diamond cutters versus the surface texture generated on the RSA 443 material. The diamond machining experiments yielded machined surfaces which are less reflective but with consistent surface roughness values. Cutting tools were observed for wear through scanning microscopy; relatively low wear pattern was evident on the diamond tool edge. The highest tool wear were obtained at higher depth of cut and increased feed rate.

  10. Modelling of stress fields during LFEM DC casting of aluminium billets by a meshless method

    NASA Astrophysics Data System (ADS)

    Mavrič, B.; Šarler, B.

    2015-06-01

    Direct Chill (DC) casting of aluminium alloys is a widely established technology for efficient production of aluminium billets and slabs. The procedure is being further improved by the application of Low Frequency Electromagnetic Field (LFEM) in the area of the mold. Novel LFEM DC processing technique affects many different phenomena which occur during solidification, one of them being the stresses and deformations present in the billet. These quantities can have a significant effect on the quality of the cast piece, since they impact porosity, hot-tearing and cold cracking. In this contribution a novel local radial basis function collocation method (LRBFCM) is successfully applied to the problem of stress field calculation during the stationary state of DC casting of aluminium alloys. The formulation of the method is presented in detail, followed by the presentation of the tackled physical problem. The model describes the deformations of linearly elastic, inhomogeneous isotropic solid with a given temperature field. The temperature profile is calculated using the in-house developed heat and mass transfer model. The effects of low frequency EM casting process parameters on the vertical, circumferential and radial stress and on the deformation of billet surface are presented. The application of the LFEM appears to decrease the amplitudes of the tensile stress occurring in the billet.

  11. Ionic fluids in lubrication of aluminium-steel contacts. Surface and tribochemical interactions

    NASA Astrophysics Data System (ADS)

    Jimenez Ballesta, Ana Eva

    Room-temperature ionic liquids (ILs) are high performance fluids with a wide thermal stability range. They are being studied as new lubricants in a variety of sliding contacts. One of their more interesting tribological applications is that of steel-aluminium lubrication. In this work we study the influence of the lateral alkyl chain length and of the anion on the lubricating ability of six imidazolium ILs, a pyridinium and a phosphonium derivative. For first time, these ILs have been studied as neat lubricants and as 1wt.% base oil additives in variable conditions of velocity, load and temperature in pin-on-disk tests for AISI 52100 steel-ASTM 2011 aluminium contacts. In this work we present the first study of ILs as lubricants under extreme temperature conditions. The tribological performance of ILs has been compared with that of a mineral oil and of a synthetic ester. Under these conditions, ILs show lower friction and wear values than conventional oils at all temperatures. As 1wt.% additives, the conditions of optimum lubrication and the transitions between regimes and lubrication mechanisms have been determined. We have also studied the performance of ILs as 1wt.% additives of the synthetic oil. A relationship between additive polarity and wear index has been established. If the more soluble phosphonium IL additive is used, no friction or wear reduction takes place due to competition between solvation and adsorption processes. Electronic microscopy (SEM), energy dispersive (EDS) and X-ray photoelectron (XPS) spectroscopies have been used to study the wear mechanisms and tribochemical processes that take place in the contact. Finally, we have studied the performance of three aluminium alloys in corrosion and erosion-corrosion tests. In immersion tests with free-water ILs, the aluminium alloy 2011 shows a good resistance to corrosion, but dilution of 1-ethyl, 3-methylimidazolium tetrafluoroborate in water produces the hydrolysis of the anion and the corrosion of

  12. The removal of iron from molten aluminium

    SciTech Connect

    Donk, H.M. van der; Nijhof, G.H.; Castelijns, C.A.M.

    1995-12-31

    In this work an overview is given about the techniques available for the removal of metallic impurities from molten aluminium. The overview is focused on the removal of iron. Also, some experimental results are given about the creation of iron-rich intermetallic compounds in an aluminium system, which are subsequently removed by gravity segregation and filtration techniques. This work is part of an ongoing research project of three major European aluminium companies who are co-operating on the subject of recycling of aluminium packaging materials recovered from household waste by means of Eddy-Current techniques. Using this technique the pick-up of some contaminating metals, particularly iron, is almost unavoidable.

  13. Novel method for joining CFRP to aluminium

    NASA Astrophysics Data System (ADS)

    Möller, F.; Thomy, C.; Vollertsen, F.; Schiebel, P.; Hoffmeister, C.; Herrmann, A. S.

    The current state of the art in joining of carbon-fibre reinforced composites (CFRP) to metals such as aluminium is - for the case of aircraft structures, e.g.- riveting or bolting. However, to reduce structural weight and improve structural performance, integral, load-bearing aluminium-CFRP-structures are desirable. To produce such structures, a novel joint configuration together with an appropriate thermal, laser-based joining process is suggested by the authors. In this paper, the joint configuration (based on CFRP-Ti-aluminium joints) and the laser beam conduction welding process will be presented, and first specimens obtained will be discussed with respect to their properties. It will be shown that the novel approach is in principle suitable to produce load-bearing CFRP-aluminium structures.

  14. Aluminium speciation in effluents and receiving waters.

    PubMed

    Gardner, M J; Comber, S D W

    2003-12-01

    The respective speciation of aluminium in sewage effluent and in river water receiving effluent, has been examined. Results showed that concentrations of reactive aluminium changed over a timescale of hours and were controlled predominantly by pH. A minimum concentration of reactive aluminium occurred at a pH of approximately 6.8, coinciding with the prevalence of non-reactive, insoluble Al(OH)3 species. For receiving waters of low pH value, typically < pH 5, a large proportion of the 'naturally present' aluminium can be present in a reactive form at concentrations higher than the proposed Environmental Quality Standard (EQS). Mixing of waters of this type with effluent of a higher pH value leads to the precipitation of aluminium hydroxide. Mixing of effluent of pH value in the range 7.5-8.0 with river water in the same (or slightly higher) pH range appears to result in no appreciable change in the proportion of reactive aluminium; the change in concentration tends to be related simply to dilution. On the basis of a theoretical knowledge of aluminium speciation, results obtained in this work indicate that it is possible to make predictions about the proportion of reactive aluminium present in a receiving water, based on the pH values of the effluent water mixture and the concentration in the effluent. Reasonable comparisons between measured and predicted values were obtained at higher pH values, but the relationship was less certain at pH values less than 6.5 for which levels of reactive metal tended to be higher than the quality standard value.

  15. A Study on Effect of Graphite Particles on Tensile, Hardness and Machinability of Aluminium 8011 Matrix Material

    NASA Astrophysics Data System (ADS)

    Latha Shankar, B.; Anil, K. C.; Karabasappagol, Prasann J.

    2016-09-01

    Industrial application point of view, metal matrix composites in general and Aluminium alloy matrix composites in particular are ideal candidates because of their favourable engineering properties. Being lightweight Aluminium matrix composites are widely used in aircraft, defence and automotive industries. In this work Aluminium 8011 metal matrix was reinforced with fine Graphite particles of 50 μm. developed by two-step Stir casting method. Graphite weight %was varied in the range 2, 4, 6 and 8%. Uniform dispersion of graphite particle is examined under optical microscope. Tensile test coupons were prepared as per standard to determine % of elongation and tensile strength for various % of graphite particle. Hardness of developed composite for various % of graphite particle and Machinability parameters were also studied for effect on surface finish. It was observed that with increase of weight percentage of Graphite particles up to 8% in Aluminium 8011 alloy matrix there was increase in tensile strength, decrease in % of elongation with increase in hardness. Machinability study revealed that, there was decrease in surface roughness with increase in Graphite content.

  16. Effect of magnesium addition on the wetting of alumina by aluminium

    NASA Astrophysics Data System (ADS)

    Sangghaleh, Ali; Halali, Mohammad

    2009-07-01

    In this report the wetting behaviour between polycrystalline alumina substrates and molten aluminium doped with magnesium as a wetting agent has been studied using the sessile drop technique. The time required for equilibrium attainment is investigated. To explore the formation of possible phases at the interface, electron microscopic studies along with EDX analysis have been employed. It is found that magnesium reduces the time and temperature required for equilibrium in the Al/Al 2O 3 system. The Al-7 wt% Mg and Al-10 wt% Mg alloys can wet alumina at temperatures as low as 900 °C. It is also found that molten aluminium doped with magnesium can wet polycrystalline alumina at temperatures below 1000 °C. A thin reaction layer was observed at the Al-Mg/Al 2O 3 interface in the present study.

  17. [Aluminium allergy and granulomas induced by vaccinations for children].

    PubMed

    Andersen, Rosa Marie Ø; Zachariae, Claus; Johansen, Jeanne Duus

    2015-04-27

    Vaccination with aluminium-adsorbed vaccines can induce aluminium allergy with persistent itching subcutaneous nodules at the injection site – vaccination granulomas. In this article we give an overview of childhood aluminium-adsorbed vaccines available in Denmark. Through literature studies we examine the incidence, the symptoms and the prognosis for the vaccination granulomas and the allergy. Finally we discuss the status in Denmark.

  18. Serum aluminium and cobalt levels after ceramic-on-ceramic and metal-on-metal total hip replacement.

    PubMed

    Grübl, A; Weissinger, M; Brodner, W; Gleiss, A; Giurea, A; Gruber, M; Pöll, G; Meisinger, V; Gottsauner-Wolf, F; Kotz, R

    2006-08-01

    In a randomised study, 28 patients with a mean age of 62.2 years (32 to 81) with osteoarthritis or avascular necrosis of the hip received either a ceramic-on-ceramic or a metal-on-metal total hip replacement. Apart from the liners the acetabular and femoral components were made of Ti-Al-Nb alloy. The serum aluminium and cobalt levels were measured before, and at one year after surgery. The 15 patients in the ceramic-on-ceramic group had a median pre-operative aluminium level of 1.3 microg/l (0.25 to 8.4) and a cobalt level below the detection limit. At one year the aluminium level was 1.1 microg/l (0.25 to 2.3) and the cobalt level was 0.4 microg/l (0.15 to 0.7). The 13 patients in the metal-on-metal group had a median pre-operative aluminium level of 1.9 microg/l (0.25 to 4.4) and a cobalt level below the detection limit. At one year the median aluminium level was 0.9 microg/l (0.25 to 3.9) whereas the cobalt level was 1.4 microg/l (0.5 to 10.5). This increase in the cobalt level at one year was significant (p < 0.001). Our findings indicate that ceramic-on-ceramic bearings do not cause elevated levels of serum aluminium in the first post-operative year.

  19. Study of Magnetic Alloys: Critical Phenomena.

    DTIC Science & Technology

    MAGNETIC ALLOYS, TRANSPORT PROPERTIES), ELECTRICAL RESISTANCE, SEEBECK EFFECT , MAGNETIC PROPERTIES, ALUMINUM ALLOYS, COBALT ALLOYS, GADOLINIUM ALLOYS, GOLD ALLOYS, IRON ALLOYS, NICKEL ALLOYS, PALLADIUM ALLOYS, PLATINUM ALLOYS, RHODIUM ALLOYS

  20. Aluminium in over-the-counter drugs: risks outweigh benefits?

    PubMed

    Reinke, Claudia M; Breitkreutz, Jörg; Leuenberger, Hans

    2003-01-01

    In the early 1970s, aluminium toxicity was first implicated in the pathogenesis of clinical disorders in patients with chronic renal failure involving bone (renal osteomalacia) or brain tissue (dialysis encephalopathy). Before that time the toxic effects of aluminium ingestion were not considered to be a major concern because absorption seemed unlikely to occur. Meanwhile, aluminium toxicity has been investigated in countless epidemiological and clinical studies as well as in animal experiments and many papers have been published on the subject. It is now commonly acknowledged that aluminium toxicity can be induced by infusion of aluminium-contaminated dialysis fluids, by parenteral nutrition solutions, and by oral exposure as a result of aluminium-containing pharmaceutical products such as aluminium-based phosphate binders or antacid intake. Over-the-counter antacids are the most important source for human aluminium exposure from a quantitative point of view. However, aluminium can act as a powerful neurological toxicant and provoke embryonic and fetal toxic effects in animals and humans after gestational exposure. Despite these facts, the patient information leaflets from European antacids that are available OTC show substantial differences regarding warnings from aluminium toxicity. It seems advisable that all patients should receive the same information on aluminium toxicity from patient information leaflets, in particular with regard to the increased absorption through concomitant administration with citrate-containing beverages and the use of such antacids during pregnancy.

  1. The interrelationship between silicon and aluminium in the biological effects of aluminium.

    PubMed

    Birchall, J D

    1992-01-01

    It is well established that aluminium is toxic at the cellular level and that pathological symptoms follow its entry into organisms (plants, fish, humans) when the normal exclusion mechanisms fail or are bypassed, as for example in renal dialysis. The present debate concerns the availability of environmental aluminium and the possible impact of its slow and insidious absorption and accumulation in vulnerable individuals. Silicon is considered as essential element but the mechanisms underlying its essentiality remain unknown and binding of the element (through oxygen) with biomolecules has not been demonstrated. There is, however, a unique affinity between aluminium and silicon, not only in solid state chemistry ([AlO4]5- and [SiO4]4- are isostructural), but also in aqueous solution chemistry as illustrated by the synthesis of zeolite from aluminate and silicate anions at high pH and under hydrothermal conditions. This affinity exists also in very dilute solution (< 10(-5) M) at near-neutral pH when hydroxyalumino-silicate species form. These species mediate the bioavailability and cellular toxicity of aluminium. The observed effects of silicon deficiency can be attributed to consequential aluminium availability. There are important implications for the epidemiology and biochemistry of aluminium-induced disorders and any consideration of one element must include the other.

  2. Molecular breeding of cereals for aluminium resistance

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Aluminium (Al3+) toxicity is the primary factor limiting crop production on acidic soils worldwide. In addition to an application of lime for soil amelioration, Al3+ resistant plant varieties have been deployed to raise productivity on such hostile soils. This has been possible due to the exploita...

  3. Effect of aluminium chloride on human spermatozoa

    SciTech Connect

    Kaur, S.

    1988-03-01

    Aluminium (Al), which is the most prevalent metal in the earth's crust, has been implicated as an etiological factor in a variety of clinical disorders. Only recently Al has been discussed in the pathogenesis of the parenteral nutrition - associated liver disease. Included in this report are the preliminary findings on its effects on the reproductive functions of human beings.

  4. An ultrafast rechargeable aluminium-ion battery

    NASA Astrophysics Data System (ADS)

    Lin, Meng-Chang; Gong, Ming; Lu, Bingan; Wu, Yingpeng; Wang, Di-Yan; Guan, Mingyun; Angell, Michael; Chen, Changxin; Yang, Jiang; Hwang, Bing-Joe; Dai, Hongjie

    2015-04-01

    The development of new rechargeable battery systems could fuel various energy applications, from personal electronics to grid storage. Rechargeable aluminium-based batteries offer the possibilities of low cost and low flammability, together with three-electron-redox properties leading to high capacity. However, research efforts over the past 30 years have encountered numerous problems, such as cathode material disintegration, low cell discharge voltage (about 0.55 volts ref. 5), capacitive behaviour without discharge voltage plateaus (1.1-0.2 volts or 1.8-0.8 volts) and insufficient cycle life (less than 100 cycles) with rapid capacity decay (by 26-85 per cent over 100 cycles). Here we present a rechargeable aluminium battery with high-rate capability that uses an aluminium metal anode and a three-dimensional graphitic-foam cathode. The battery operates through the electrochemical deposition and dissolution of aluminium at the anode, and intercalation/de-intercalation of chloroaluminate anions in the graphite, using a non-flammable ionic liquid electrolyte. The cell exhibits well-defined discharge voltage plateaus near 2 volts, a specific capacity of about 70 mA h g-1 and a Coulombic efficiency of approximately 98 per cent. The cathode was found to enable fast anion diffusion and intercalation, affording charging times of around one minute with a current density of ~4,000 mA g-1 (equivalent to ~3,000 W kg-1), and to withstand more than 7,500 cycles without capacity decay.

  5. Indentation of aluminium foam at low velocity

    NASA Astrophysics Data System (ADS)

    Shi, Xiaopeng; Miao, Yinggang; Liu, Shuangyan; Li, Yulong; Lu, Guoxing

    2015-09-01

    The indentation behaviour of aluminium foams at low velocity (10 m/s ˜ 30 m/s) was investigated both in experiments and numerical simulation in this paper. A flat-ended indenter was used and the force-displacement history was recorded. The Split Hopkinson Pressure bar was used to obtain the indentation velocity and forces in the dynamic experiments. Because of the low strength of the aluminium foam, PMMA bar was used, and the experimental data were corrected using Bacon's method. The energy absorption characteristics varying with impact velocity were then obtained. It was found that the energy absorption ability of aluminium foam gradually increases in the quasi-static regime and shows a significant increase at ˜10 m/s velocity. Numerical simulation was also conducted to investigate this process. A 3D Voronoi model was used and models with different relative densities were investigated as well as those with different failure strain. The indentation energy increases with both the relative density and failure strain. The analysis of the FE model implies that the significant change in energy absorption ability of aluminium foam in indentation at ˜10 m/s velocity may be caused by plastic wave effect.

  6. Toxicity of dissolved and precipitated aluminium to marine diatoms.

    PubMed

    Gillmore, Megan L; Golding, Lisa A; Angel, Brad M; Adams, Merrin S; Jolley, Dianne F

    2016-05-01

    Localised aluminium contamination can lead to high concentrations in coastal waters, which have the potential for adverse effects on aquatic organisms. This research investigated the toxicity of 72-h exposures of aluminium to three marine diatoms (Ceratoneis closterium (formerly Nitzschia closterium), Minutocellus polymorphus and Phaeodactylum tricornutum) by measuring population growth rate inhibition and cell membrane damage (SYTOX Green) as endpoints. Toxicity was correlated to the time-averaged concentrations of different aluminium size-fractions, operationally defined as <0.025μm filtered, <0.45μm filtered (dissolved) and unfiltered (total) present in solution over the 72-h bioassay. The chronic population growth rate inhibition after aluminium exposure varied between diatom species. C. closterium was the most sensitive species (10% inhibition of growth rate (72-h IC10) of 80 (55-100)μg Al/L (95% confidence limits)) while M. polymorphus (540 (460-600)μg Al/L) and P. tricornutum (2100 (2000-2200)μg Al/L) were less sensitive (based on measured total aluminium). Dissolved aluminium was the primary contributor to toxicity in C. closterium, while a combination of dissolved and precipitated aluminium forms contributed to toxicity in M. polymorphus. In contrast, aluminium toxicity to the most tolerant diatom P. tricornutum was due predominantly to precipitated aluminium. Preliminary investigations revealed the sensitivity of C. closterium and M. polymorphus to aluminium was influenced by initial cell density with aluminium toxicity significantly (p<0.05) increasing with initial cell density from 10(3) to 10(5)cells/mL. No effects on plasma membrane permeability were observed for any of the three diatoms suggesting that mechanisms of aluminium toxicity to diatoms do not involve compromising the plasma membrane. These results indicate that marine diatoms have a broad range in sensitivity to aluminium with toxic mechanisms related to both dissolved and precipitated

  7. A numerical analysis of empty and foam-filled aluminium conical tubes under oblique impact loading

    NASA Astrophysics Data System (ADS)

    Mat, Fauziah; Ismail, Khairul Azwan; Yaacob, Sazali

    2015-05-01

    In real impact applications, an energy absorber rarely sustains dynamic loading either axial or oblique but a combination of both. Established studies have proved that thin-walled tube is an excellent energy absorber under dynamic loading. Furthermore, the introduction of foam filling successfully enhanced the energy absorption capacity of thin-walled tube. However, the understanding of its response under oblique loading has yet been fully explored. Moreover, emerging in automotive industry has lead to increase interests on lightweight materials such as aluminium alloy. As such, this paper presents the crushing behaviour of empty and foam-filled aluminium alloy (AA6061-T6) conical tubes under oblique impact loading using a validated nonlinear finite element (FE) code, LS-DYNA. The study aims to assess the effect of foam filling on the energy absorption of AA6061-T6 tubes for variations in filler density. In fact, to the best of our knowledge, this study is the first attempt to evaluate a response of empty and foam-filled aluminum conical tube by using an experimentally validated model under oblique dynamic loading conditions. Good correlations between the numerical and experimental results were observed. The study show that initial peak force and the energy absorption increase with increasing filler density under axial and oblique loading. On the other hand, the effect of foam filling (0.534 g/cm3 aluminium foam filler) is less pronounced for the initial peak force under axial impact loading. Furthermore, the initial peak force and dynamic force of empty and foam-filled AA6061-T6 conical tubes decrease as the load angle increases from 0 deg to 20 deg hence reduces the energy absorption capacity.

  8. Fabrication of ultra-fine grained aluminium tubes by RTES technique

    SciTech Connect

    Jafarzadeh, H. Abrinia, K.

    2015-04-15

    Recently, repetitive tube expansion and shrinking have been exploited as a means for producing ultra-fine grained and nano-crystalline microstructures for magnesium alloy tubes. This method includes two different half-cycles and was based on pressing a tubular part through an angular channel die with two shear zones. Since the aluminium alloys are the most widely used materials in industries, in this study, repetitive tube expansion and shrinking as a new severe plastic deformation technique was applied to commercially pure aluminium for fabricating ultra-fine grained aluminium tubes for the first time and the ability of this process in significant grain refinement is determined even after single cycle. Transmission electron microscopy and X-ray diffraction were used to evaluate the microstructure of the repetitive tube expansion and shrinking processed materials and the examinations showed ultra-fine grains with the average grain size of 320 nm after one cycle of repetitive tube expansion and shrinking. The yield strength, ultimate tensile strength increased notably by the factor of 2.17 and 1.27 respectively, after one cycle of repetitive tube expansion and shrinking, whereas the elongation to failure as well as the uniform elongation decreased. Furthermore, micro-hardness distribution through the part's section proposed the hardness increasing to ~ 55 HV from the initial value of ~ 28 HV after one cycle of repetitive tube expansion and shrinking. - Highlights: • RTES was introduced for fabricating the UFGed AA1050 tubes for the first time. • Nano-grained AA1050 tube was obtained by RTES process. • Grain size of ~ 320 nm was obtained after two half-cycles of RTES process. • Yield and ultimate strength increased by the factor of 2.17 and 1.27 respectively. • The microhardness increased to ~ 55 HV from the initial value of ~ 28 HV.

  9. Microemulsion extraction separation and determination of aluminium species by spectrofluorimetry.

    PubMed

    Lu, Jusheng; Tian, Jiuying; Guo, Na; Wang, Yan; Pan, Yichun

    2011-01-30

    A simple and sensitive microemulsion extraction separation method was developed for the speciation of aluminium in tea samples by spectrofluorimetry. With 8-hydroxyquinoline (8-HQ) as the chelating agent and Triton X-100 Winsor II microemulsion as the extractant, separation of aluminium species in different pH solutions was achieved by microemulsion extraction. The formation of microemulsion, the conditions of extraction and determination of aluminium species were studied. The results showed that, the contents of aluminium species in tea leaves and infusions samples, such as total aluminium, total soluble aluminium, total granular aluminium, inorganic aluminium except Al-F, and (Al-F+Al-org), were obtained successfully under the optimal conditions. The limit of detection was 0.23 μg L(-1) in pH 9.5 solution, and 0.59 μg L(-1) in pH 6.0 solution respectively; the precision (RSD) for 11 replicate measurements of 10 μg L(-1) aluminium was 2.1% in pH 9.5 solution, and 2.8% in pH 6.0 solution respectively; the recoveries for the spiked samples were 96.8-103.5%. The proposed method is simple and efficient, which has been applied to the speciation of aluminium in tea samples with satisfactory results.

  10. Aluminium in brain tissue in familial Alzheimer's disease.

    PubMed

    Mirza, Ambreen; King, Andrew; Troakes, Claire; Exley, Christopher

    2017-03-01

    The genetic predispositions which describe a diagnosis of familial Alzheimer's disease can be considered as cornerstones of the amyloid cascade hypothesis. Essentially they place the expression and metabolism of the amyloid precursor protein as the main tenet of disease aetiology. However, we do not know the cause of Alzheimer's disease and environmental factors may yet be shown to contribute towards its onset and progression. One such environmental factor is human exposure to aluminium and aluminium has been shown to be present in brain tissue in sporadic Alzheimer's disease. We have made the first ever measurements of aluminium in brain tissue from 12 donors diagnosed with familial Alzheimer's disease. The concentrations of aluminium were extremely high, for example, there were values in excess of 10μg/g tissue dry wt. in 5 of the 12 individuals. Overall, the concentrations were higher than all previous measurements of brain aluminium except cases of known aluminium-induced encephalopathy. We have supported our quantitative analyses using a novel method of aluminium-selective fluorescence microscopy to visualise aluminium in all lobes of every brain investigated. The unique quantitative data and the stunning images of aluminium in familial Alzheimer's disease brain tissue raise the spectre of aluminium's role in this devastating disease.

  11. A study on the surface shape and roughness of aluminum alloy for heat exchanger using ball end milling

    NASA Astrophysics Data System (ADS)

    Lee, E.; Kim, Y.; jeong, H.; Chung, H.

    2015-09-01

    Aluminum alloy is a material with a high strength-weight ratio and excellent thermal conductivity. It neither readily corrodes nor quickly weakens at low temperatures, but can be easily recycled. Because of these features, aluminum heat exchangers are widely used in aluminum alloy. In addition, the aluminum alloy used in other areas is expected to gradually increase. As a result, researchers have been continuously studying the cutting patterns of aluminium alloy. However, such studies are fewer than those on the cutting patterns of ordinary steel. Moreover, the research on ball end milling with aluminium alloys has not received much attention. Therefore, in this study, an attempt was made to find the optimal cutting pattern among the seven cutting patterns for the machining of the commonly used aluminum alloy using ball end milling for a heat exchanger. The optimal pattern was found by comparing the different shapes and surface roughness values produced by the seven patterns.

  12. Radiation-stimulated diffusion in Al-Si alloys

    NASA Astrophysics Data System (ADS)

    Kiv, A.; Fuks, D.; Munitz, A.; Zenou, V.; Moiseenko, N.

    A di-vacancy low-temperature diffusion is proposed to explain diffusion-controlled processes in Al-Si alloys responsible for neutron-induced silicon precipitation. Ab initio calculations of potential barriers for Si atom hopping in aluminium lattice showed that in the case of di-vacancy diffusion, they are small compared with that of mono-vacancy diffusion. The low temperature diffusivity of mono-vacancies is too small to account for the measured Si diffusivities in aluminium. The dependencies of radiation-stimulated diffusion on the neutron flux and on the temperature are obtained and can be used for the experimental verification of the developed model.

  13. Laser welding of copper and aluminium battery interconnections

    NASA Astrophysics Data System (ADS)

    De Bono, Paola; Blackburn, Jon

    2015-07-01

    The adoption of lithium-ion and/or super-capacitor battery technologies is a current hot topic in the automotive industry. For both battery types, the terminals and busbars are manufactured from copper (Cu) and/or aluminium-based (Al-based) alloys, as a result of their high electrical and thermal conductivities. Laser welding is considered an attractive process to industry due to its easy automotability, high processing speed and highly repeatable cost-effective processing. However, laser welding of Cu-Cu and Al-Al joints presents several difficulties due to the high surface reflectivity at infrared (IR) wavelengths. This behaviour becomes even more critical when processing thin sheets and foils.This paper summarises recent work performed to develop laser welding techniques suitable for monometallic joining of Cu-Cu and Al-Al electrical interconnections. Laser welding of multiple overlapped foils (with thickness in the range of 17μm-100μm) were investigated.

  14. Feet sunk in molten aluminium: The burn and its prevention.

    PubMed

    Alonso-Peña, David; Arnáiz-García, María Elena; Valero-Gasalla, Javier Luis; Arnáiz-García, Ana María; Campillo-Campaña, Ramón; Alonso-Peña, Javier; González-Santos, Jose María; Fernández-Díaz, Alaska Leonor; Arnáiz, Javier

    2015-08-01

    Nowadays, despite improvements in safety rules and inspections in the metal industry, foundry workers are not free from burn accidents. Injuries caused by molten metals include burns secondary to molten iron, aluminium, zinc, copper, brass, bronze, manganese, lead and steel. Molten aluminium is one of the most common causative agents of burns (60%); however, only a few publications exist concerning injuries from molten aluminium. The main mechanisms of lesion from molten aluminium include direct contact of the molten metal with the skin or through safety apparel, or when the metal splash burns through the pants and rolls downward along the leg. Herein, we report three cases of deep dermal burns after 'soaking' the foot in liquid aluminium and its evolutive features. This paper aims to show our experience in the management of burns due to molten aluminium. We describe the current management principles and the key features of injury prevention.

  15. What is the risk of aluminium as a neurotoxin?

    PubMed

    Exley, Christopher

    2014-06-01

    Aluminium is neurotoxic. Its free ion, Al(3+) (aq), is highly biologically reactive and uniquely equipped to do damage to essential cellular (neuronal) biochemistry. This unequivocal fact must be the starting point in examining the risk posed by aluminium as a neurotoxin in humans. Aluminium is present in the human brain and it accumulates with age. The most recent research demonstrates that a significant proportion of individuals older than 70 years of age have a potentially pathological accumulation of aluminium somewhere in their brain. What are the symptoms of chronic aluminium intoxication in humans? What if neurodegenerative diseases such as Alzheimer's disease are the manifestation of the risk of aluminium as a neurotoxin? How might such an (outrageous) hypothesis be tested?

  16. Alloy materials

    DOEpatents

    Hans Thieme, Cornelis Leo; Thompson, Elliott D.; Fritzemeier, Leslie G.; Cameron, Robert D.; Siegal, Edward J.

    2002-01-01

    An alloy that contains at least two metals and can be used as a substrate for a superconductor is disclosed. The alloy can contain an oxide former. The alloy can have a biaxial or cube texture. The substrate can be used in a multilayer superconductor, which can further include one or more buffer layers disposed between the substrate and the superconductor material. The alloys can be made a by process that involves first rolling the alloy then annealing the alloy. A relatively large volume percentage of the alloy can be formed of grains having a biaxial or cube texture.

  17. Optimizing friction stir welding parameters to maximize tensile strength of AA2219 aluminum alloy joints

    NASA Astrophysics Data System (ADS)

    Babu, S.; Elangovan, K.; Balasubramanian, V.; Balasubramanian, M.

    2009-04-01

    AA2219 aluminium alloy (Al-Cu-Mn alloy) has gathered wide acceptance in the fabrication of lightweight structures requiring a high strength-to-weight ratio and good corrosion resistance. In contrast to the fusion welding processes that are routinely used for joining structural aluminium alloys, the friction stir welding (FSW) process is an emerging solid state joining process in which the material that is being welded does not melt and recast. This process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters such as tool rotational speed, welding speed, axial force etc., and the tool pin profile play a major role in determining the joint strength. An attempt has been made here to develop a mathematical model to predict the tensile strength of friction stir welded AA2219 aluminium alloy by incorporating FSW process parameters. A central composite design with four factors and five levels has been used to minimize the number of experimental conditions. The response surface method (RSM) has been used to develop the model. The developed mathematical model has been optimized using the Hooke and Jeeves search technique to maximize the tensile strength of the friction stir welded AA2219 aluminium alloy joints.

  18. Improvement of photodynamic activity of aluminium sulphophthalocyanine due to biotinylation

    NASA Astrophysics Data System (ADS)

    Meerovich, Irina G.; Jerdeva, Victoria V.; Derkacheva, Valentina M.; Meerovich, Gennadii A.; Lukyanets, Eugeny A.; Kogan, Eugenia A.; Savitsky, Alexander P.

    2003-09-01

    The photodynamic activity of dibiotinylated aluminium sulphophthalocyanine in vitro and in vivo were studied. It was obtained that in vitro dibiotinylated aluminium sulphophthalocyanine provides the effective damage of small cell lung carcinoma OAT-75. In vivo dibiotinylated aluminium sulphophthalocyanine causes destruction of tumor (Erlich carcinoma), results in total necrosis of tumor tissue and expresses vascular damage (trombosis and destruction of vascular walls) even in concentration 0.25 mg/kg of a body weight.

  19. An ultrafast rechargeable aluminium-ion battery.

    PubMed

    Lin, Meng-Chang; Gong, Ming; Lu, Bingan; Wu, Yingpeng; Wang, Di-Yan; Guan, Mingyun; Angell, Michael; Chen, Changxin; Yang, Jiang; Hwang, Bing-Joe; Dai, Hongjie

    2015-04-16

    The development of new rechargeable battery systems could fuel various energy applications, from personal electronics to grid storage. Rechargeable aluminium-based batteries offer the possibilities of low cost and low flammability, together with three-electron-redox properties leading to high capacity. However, research efforts over the past 30 years have encountered numerous problems, such as cathode material disintegration, low cell discharge voltage (about 0.55 volts; ref. 5), capacitive behaviour without discharge voltage plateaus (1.1-0.2 volts or 1.8-0.8 volts) and insufficient cycle life (less than 100 cycles) with rapid capacity decay (by 26-85 per cent over 100 cycles). Here we present a rechargeable aluminium battery with high-rate capability that uses an aluminium metal anode and a three-dimensional graphitic-foam cathode. The battery operates through the electrochemical deposition and dissolution of aluminium at the anode, and intercalation/de-intercalation of chloroaluminate anions in the graphite, using a non-flammable ionic liquid electrolyte. The cell exhibits well-defined discharge voltage plateaus near 2 volts, a specific capacity of about 70 mA h g(-1) and a Coulombic efficiency of approximately 98 per cent. The cathode was found to enable fast anion diffusion and intercalation, affording charging times of around one minute with a current density of ~4,000 mA g(-1) (equivalent to ~3,000 W kg(-1)), and to withstand more than 7,500 cycles without capacity decay.

  20. Structural engineering of nanoporous anodic aluminium oxide by pulse anodization of aluminium.

    PubMed

    Lee, Woo; Schwirn, Kathrin; Steinhart, Martin; Pippel, Eckhard; Scholz, Roland; Gösele, Ulrich

    2008-04-01

    Nanoporous anodic aluminium oxide has traditionally been made in one of two ways: mild anodization or hard anodization. The first method produces self-ordered pore structures, but it is slow and only works for a narrow range of processing conditions; the second method, which is widely used in the aluminium industry, is faster, but it produces films with disordered pore structures. Here we report a novel approach termed "pulse anodization" that combines the advantages of the mild and hard anodization processes. By designing the pulse sequences it is possible to control both the composition and pore structure of the anodic aluminium oxide films while maintaining high throughput. We use pulse anodization to delaminate a single as-prepared anodic film into a stack of well-defined nanoporous alumina membrane sheets, and also to fabricate novel three-dimensional nanostructures.

  1. Separation of actinides from irradiated An-Zr based fuel by electrorefining on solid aluminium cathodes in molten LiCl-KCl

    NASA Astrophysics Data System (ADS)

    Souček, P.; Murakami, T.; Claux, B.; Meier, R.; Malmbeck, R.; Tsukada, T.; Glatz, J.-P.

    2015-04-01

    An electrorefining process for metallic spent nuclear fuel treatment is being investigated in ITU. Solid aluminium cathodes are used for homogeneous recovery of all actinides within the process carried out in molten LiCl-KCl eutectic salt at a temperature of 500 °C. As the selectivity, efficiency and performance of solid Al has been already shown using un-irradiated An-Zr alloy based test fuels, the present work was focused on laboratory-scale demonstration of the process using irradiated METAPHIX-1 fuel composed of U67-Pu19-Zr10-MA2-RE2 (wt.%, MA = Np, Am, Cm, RE = Nd, Ce, Gd, Y). Different electrorefining techniques, conditions and cathode geometries were used during the experiment yielding evaluation of separation factors, kinetic parameters of actinide-aluminium alloy formation, process efficiency and macro-structure characterisation of the deposits. The results confirmed an excellent separation and very high efficiency of the electrorefining process using solid Al cathodes.

  2. [Effect of casting techniques on castability of copper-aluminum alloys].

    PubMed

    Scaranelo, R M; Bombonatti, P E; de Barros, L E; Pellizzer, A J

    1990-01-01

    It was evaluated the castability of four copper-aluminium alloy according the melting casting method used. The specimens were made using polyester mesh screen, with 11 x 11 filaments of 0.26 mm thick, fixed along of two adjacent edges in wax bar, with the sprue attached at their junction. The alloys were in an electrical casting machine and a centrifugal casting machine with an air/gas torch. The castability values were obtained by the percentage of completed segments of the resulting cast alloy screen. It was verified that the use of the electrical casting machine produced higher castability values to the copper-aluminium alloys than those produced by a centrifugal casting machine with an air/gas torch.

  3. Plasma Electrolytic Oxidation (PEO) Coatings on an A356 Alloy for Improved Corrosion and Wear Resistance

    NASA Astrophysics Data System (ADS)

    Peng, Zhijing

    Plasma electrolytic oxidizing (PEO) is an advanced technique that has been used to deposit thick and hard ceramic coatings on aluminium (Al) alloys. This work was however to use the PEO process to produce thin ceramic oxide coatings on an A356 Al alloy for improving corrosion and wear resistance of the alloy. Effects of current density and treatment time on surface morphologies and thickness of the PEO coatings were investigated. The improvement of galvanic corrosion properties of the coated A356 alloy vs. steel and carbon fibre were evaluated in E85 fuel or NaCl environments. Tribological properties of the coatings were studied with comparison to the uncoated A356 substrate and other commercially-used engine bore materials. The research results indicated that the PEO coatings could have excellent tribological and corrosion properties for aluminium engine applications.

  4. Speciation analysis of aluminium and aluminium fluoride complexes by HPIC-UVVIS.

    PubMed

    Frankowski, Marcin; Zioła-Frankowska, Anetta

    2010-10-15

    The study presents a new analytical method for speciation analysis in fractionation of aluminium fluoride complexes and free Al(3+) in soil samples. Aluminium speciation was studied in model solutions and soil extract samples by means of high performance ion chromatography (HPIC) with UV-VIS detection using post-column reaction with tiron for the separation and detection of aluminium fluoride complex and Al(3+) forms during one analysis. The paper presents particular stages of the chromatographic process optimization involving selecting the appropriate eluent strength, type of elution or concentration and quantity of derivatization reagent. HPIC was performed on a bifunctional analytical column Dionex IonPac CS5A. The use of gradient elution and the eluents A: 1M NH(4)Cl and B: water acidified to pH of eluent phase, enabled full separation of fluoride aluminium forms as AlF(2)(+), AlF(3)(0), AlF(4)(-) (first signal), AlF(2+) (second signal) and form Al(3+) in a single analytical procedure. The proposed new method HPIC-UVVIS was applied successfully in the quantitative and qualitative analysis of soil samples.

  5. Ratcheting fatigue behaviour of Al-7075 T6 alloy: Influence of stress parameters

    NASA Astrophysics Data System (ADS)

    Amarnath, Lala; Bhattacharjee, Antara; Dutta, K.

    2016-02-01

    The use of aluminium and aluminium based alloys are increasing rapidly on account of its high formability, good thermal and electrical conductivity, high strength and lightness. Aluminium alloys are extensively used in aerospace, automobile, marine and space research industries and are also put into structural applications where chances of fatigue damage cannot be ruled out. In the current work, it is intended to study the ratcheting fatigue behavior of 7075-T6 aluminium alloy at room temperature. This Al alloy is potentially used in aviation, marine and automotive components as well as in bicycle parts, rock mounting equipment and parts of ammunition where there is every chance of failure of the parts due to deformation caused by ratcheting. Ratcheting is the process of accruement of plastic stain produced when a component is subjected to asymmetric cyclic loading under the influence of low cycle fatigue. To accomplish the requirements of the projected research, stress-controlled cyclic loading experiments were done using a ±250 kN servo-hydraulic universal testing machine (Instron: 8800R). The effect of stress parameters such as mean stress and stress amplitude were investigated on the ratcheting behavior of the selected aluminium alloy. It was observed that, ratcheting strain increased with increase in the value of stress amplitude at any constant mean stress while a saturation in strain accumulation attained in the investigated material after around 10-20 cycles, under all test conditions. The analyses of hysteresis loop generated during cyclic loading indicate that the material exhibits cyclic hardening in the initial fifty cycles which gets softened in further loading up to about 70-80 cycles and finally attains a steady state. The increase in the ratcheting strain value with stress parameters happens owing to increased deformation domain during cycling. The cyclic hardening accompanied by softening is correlated with characteristic precipitation features of

  6. Preparation of SiC based Aluminium metal matrix nano composites by high intensity ultrasonic cavitation process and evaluation of mechanical and tribological properties

    NASA Astrophysics Data System (ADS)

    Murthy, N. V.; Prasad Reddy, A.; Selvaraj, N.; Rao, C. S. P.

    2016-09-01

    Request augments on a worldwide scale for the new materials. The metal matrix nano composites can be used in numerous applications of helicopter structural parts, gas turbine exit guide vane's, space shuttle, and other structural applications. The key mailman to ameliorate performance of composite matrix in aluminium alloy metal reinforces nano particles in the matrix of alloy uniformly, which ameliorates composite properties without affecting limit of ductility. The ultrasonic assisted stir casting helped agitation was successfully used to fabricate Al 2219 metal matrix of alloy reinforced with (0.5, 1, 1.5 and 2) wt.% of nano silicon carbide (SiC) particles of different sizes 50nm and 150nm. The micrographs of scanning electron microscopy of nano composite were investigated it reveals that the uniform dispersion of nano particles silicon carbide in aluminium alloy 2219 matrix and with the low porosity. How the specific wear rate was vary with increasing weight percentage of nano particles at constant load and speed as shown in results and discussions. And the mechanical properties showed that the ultimate tensile strength and hardness of metal matrix nano composite AA 2219 / nano SiC of 50nm and 150nm lean to augment with increase weight percentage of silicon carbide content in the matrix alloy.

  7. Aluminium salt slag characterization and utilization--a review.

    PubMed

    Tsakiridis, P E

    2012-05-30

    Aluminium salt slag (also known as aluminium salt cake), which is produced by the secondary aluminium industry, is formed during aluminium scrap/dross melting and contains 15-30% aluminium oxide, 30-55% sodium chloride, 15-30% potassium chloride, 5-7% metallic aluminium and impurities (carbides, nitrides, sulphides and phosphides). Depending on the raw mix the amount of salt slag produced per tonne of secondary aluminium ranges from 200 to 500 kg. As salt slag has been classified as toxic and hazardous waste, it should be managed in compliance with the current legislation. Its landfill disposal is forbidden in most of the European countries and it should be recycled and processed in a proper way by taking the environmental impact into consideration. This paper presents a review of the aluminium salt slag chemical and mineralogical characteristics, as well as various processes for metal recovery, recycling of sodium and potassium chlorides content back to the smelting process and preparation of value added products from the final non metallic residue.

  8. Aluminium removal from water after defluoridation with the electrocoagulation process.

    PubMed

    Sinha, Richa; Mathur, Sanjay; Brighu, Urmila

    2015-01-01

    Fluoride is the most electronegative element and has a strong affinity for aluminium. Owing to this fact, most of the techniques used for fluoride removal utilized aluminium compounds, which results in high concentrations of aluminium in treated water. In the present paper, a new approach is presented to meet the WHO guideline for residual aluminium concentration as 0.2 mg/L. In the present work, the electrocoagulation (EC) process was used for fluoride removal. It was found that aluminium content in water increases with an increase in the energy input. Therefore, experiments were optimized for a minimum energy input to achieve the target value (0.7 mg/L) of fluoride in resultant water. These optimized sets were used for further investigations of aluminium control. The experimental investigations revealed that use of bentonite clay as coagulant in clariflocculation brings down the aluminium concentration of water below the WHO guideline. Bentonite dose of 2 g/L was found to be the best for efficient removal of aluminium.

  9. Reciprocating Sliding Behaviour of Solid Lubricant Coating over Modified Titanium Alloy Surfaces

    NASA Astrophysics Data System (ADS)

    Jothi Prakash, V. M.; Sathish, S.; Gopalakrishnan, T.; Venugopal, S.

    2017-03-01

    Tribological behaviour of contacting surfaces rigid sphere is using flat plate the with influence of normal and tangential loading (shear traction) is analysed using FEA model and surfaces being coated on flat plate by Titanium Alloy, Aluminium Alloy Molybdenum Di-sulphide. The finite element model facilitates to Evaluating the surface variables like contact stress distribution with the surface level and surface, contact pressure, shear stress and displacement. The finite element solution is validated through the hertz solution and on the successful verification.

  10. Effect of Weight Percentage and Cutting Parameter on Surface Finish of SiC Reinforced Aluminium Composite

    NASA Astrophysics Data System (ADS)

    Kadadevaramath, R. S.; Kotresh, M. C.; Srinivasan, D.

    2016-09-01

    In the present work, aluminium alloy of series 1100 is selected as a matrix material and SiC of 45 microns as reinforcement. The composites are synthesized by 2 stage stir casting route, by varying a weight % of reinforcement from 6 % and 10%. The surface roughness of prepared composite were examined after plain turning operation. The machining parameters like speed, feed, DOC, SiC Wt. % are varied at 3 different levels. In order to minimize the time, cost and material a taguchi L9 orthogonal array was used for experiment. From the studies it was observed that the roughness value will increase with the increasing in reinforcement percentage.

  11. Galvanised steel to aluminium joining by laser and GTAW processes

    SciTech Connect

    Sierra, G.; Peyre, P.; Deschaux Beaume, F. Stuart, D.; Fras, G.

    2008-12-15

    A new means of assembling galvanised steel to aluminium involving a reaction between solid steel and liquid aluminium was developed, using laser and gas tungsten arc welding (GTAW) processes. A direct aluminium melting strategy was investigated with the laser process, whereas an aluminium-induced melting by steel heating and heat conduction through the steel was carried out with the GTAW process. The interfaces generated during the interaction were mainly composed of a 2-40 {mu}m thick intermetallic reaction layers. The linear strength of the assemblies can be as high as 250 N/mm and 190 N/mm for the assemblies produced respectively by laser and GTAW processes. The corresponding failures were located in the fusion zone of aluminium (laser assemblies), or in the reaction layer (GTAW assemblies)

  12. Aluminium Electroplating on Steel from a Fused Bromide Electrolyte

    SciTech Connect

    Prabhat Tripathy; Laura Wurth; Eric Dufek; Toni Y. Gutknecht; Natalie Gese; Paula Hahn; Steven Frank; Guy Fredrickson; J Stephen Herring

    2014-08-01

    A quaternary bromide bath (LiBr-KBr-CsBr-AlBr3) was used to electro-coat aluminium on steel substrates. The electrolyte was prepared by the addition of AlBr3 into the eutectic LiBr-KBr-CsBr melt. A smooth, thick, adherent and shiny aluminium coating could be obtained with 80 wt.% AlBr3 in the ternary melt. The SEM photographs of the coated surfaces suggest the formation of thick and dense coatings with good aluminium coverage. Both salt immersion and open circuit potential measurement suggest that the coatings did display good corrosion-resistance behavior. Annealing of the coated surfaces, prior to corrosion tests, suggested the robustness of the metallic aluminium coating in preventing the corrosion of the steel surfaces. Studies also indicated that the quaternary bromide plating bath can potentially provide a better aluminium coating on both ferrous and non-ferrous metals, including complex surfaces/geometries.

  13. Multilayer roll bonded aluminium foil: processing, microstructure and flow stress

    SciTech Connect

    Barlow, C.Y.; Nielsen, P.; Hansen, N

    2004-08-02

    Bulk aluminium has been produced by warm-rolling followed by cold-rolling of commercial purity (99% purity) aluminium foil. The bonding appeared perfect from observation with the naked eye, light and transmission electron microscopy. By comparison with bulk aluminium of similar purity (AA1200) rolled to a similar strain (90%RA), the roll-bonded metal showed a much higher density of high-angle grain boundaries, similar strength and improved thermal stability. This study has implications for a number of applications in relation to the processing of aluminium. Roll bonding is of interest as a method for grain size refinement; oxide-containing materials have increased strength, enhanced work-hardening behaviour, and exhibit alterations in recrystallisation behaviour. The behaviour of the hard oxide film is of interest in aluminium processing, and has been investigated by characterising the size and distribution of oxide particles in the roll-bonded samples.

  14. Usage of Neural Network to Predict Aluminium Oxide Layer Thickness

    PubMed Central

    Michal, Peter; Vagaská, Alena; Gombár, Miroslav; Kmec, Ján; Spišák, Emil; Kučerka, Daniel

    2015-01-01

    This paper shows an influence of chemical composition of used electrolyte, such as amount of sulphuric acid in electrolyte, amount of aluminium cations in electrolyte and amount of oxalic acid in electrolyte, and operating parameters of process of anodic oxidation of aluminium such as the temperature of electrolyte, anodizing time, and voltage applied during anodizing process. The paper shows the influence of those parameters on the resulting thickness of aluminium oxide layer. The impact of these variables is shown by using central composite design of experiment for six factors (amount of sulphuric acid, amount of oxalic acid, amount of aluminium cations, electrolyte temperature, anodizing time, and applied voltage) and by usage of the cubic neural unit with Levenberg-Marquardt algorithm during the results evaluation. The paper also deals with current densities of 1 A·dm−2 and 3 A·dm−2 for creating aluminium oxide layer. PMID:25922850

  15. Further Precipitation Reactions Associated with Beta’ (Al3Zr) Particles in Al-Li-Cu-Mg-Zr Alloys

    DTIC Science & Technology

    1988-12-01

    Gregson 8’ precipitation in Al-Li-Mg-Cu-Zr alloys. H.M. Flower J. Mater. Sci. Lett., 3, 829 (1984) 5 P.L. Makin On the ageing of an aluminium-lithium...Technol., 2, 349 (1986) 8 H.M. Flower The effect of composition and heat treatment upon the et al microstructure/property relationships in Al-Li-Cu-Mg...1119 REFERENCES concluded) No. Author Title, etc 10 P.J. Gregon Microstructural control of toughness in aluminium- H.M. Flower lithium alloys. Acta

  16. Amélioration des performances du procédé de soudage TIG sur un acier au carbone et un alliage d'aluminium par dépôt de silice

    NASA Astrophysics Data System (ADS)

    Sire, Stéphane; Marya, Surendar

    This Note presents ways to improve the weld penetration potential of TIG process by optimising silica application around the joints in a plain carbon steel and an aluminium alloy 5086. Whereas for plain carbon steels, full coverage of joint improves penetration, the presence of a blank zone around the joint in the flux coating on aluminium 5086 using AC-TIG seems to be the best solution for cosmetic and deep welds. To cite this article: S. Sire, S. Marya, C. R. Mecanique 330 (2002) 83-89.

  17. Oxidation behaviors of the aluminide coated TZM alloy via pack cementation

    NASA Astrophysics Data System (ADS)

    Park, J.; Kim, J. M.; Lee, S.; Park, J. S.

    2014-12-01

    TZM is a traditional alloy for high temperature applications, in which (Ti, Zr)C particles are dispersed in a Mo matrix. However, due to easy formation of an oxide layer on the TZM alloy under ambient atmosphere, an oxidation protective coating is needed for any high temperature structural applications of TZM. In this study, aluminium pack cementation coatings have been carried out on TZM alloys, resulting in the formation of Al8Mo3 layer on the surface of TZM alloys. In order to examine the oxidation stability, the TZM alloy was exposed in an aerobic atmosphere. For the aluminide coated TZM alloys, an alumina layer was produced at the outer surface layer. The alminide coated TZM alloys showed excellent oxidation resistance. The coating layer kinetics and the corresponding oxidation stability are also discussed in terms of microstructural observations.

  18. Scanning and transmission electron microscopy study of the microstructural changes occurring in aluminium matrix composites reinforced with SiC particles during casting and welding: interface reactions

    PubMed

    Urena; Gomez De Salazar JM; Gil; Escalera; Baldonedo

    1999-11-01

    Processing of aluminium matrix composites (AMCs), especially those constituted by a reactive system such as Al-SiC, presents great difficulties which limit their potential applications. The interface reactivity between SiC and molten Al generates an aluminium carbide which degrades the composite properties. Scanning and transmission electron microscopes equipped with energy-dispersive X-ray spectroscopes are essential tools for determining the structure and chemistry of the Al-SiC interfaces in AMCs and changes occurring during casting and arc welding. In the present work, an aluminium-copper alloy (AA2014) reinforced with three different percentages of SiC particles was subjected to controlled remelting tests, at temperatures in the range 750-900 degrees C for 10 and 30 min. Arc welding tests using a tungsten intert gas with power inputs in the range 850-2000 W were also carried out. The results of these studies showed that during remelting there is preferential SiC particle consumption with formation of Al4C3 by interface reaction between the solid SiC particle and the molten aluminium matrix. The formation of Al4C3 by the same mechanism has also been detected in molten pools of arc welded composites. However, in this case there was formation of an almost continuous layer of Al4C3, which protects the particle against further consumption, and formation of aciculate aluminium carbide on the top weld. Both are formed by fusion and dissolution of the SiC in molten aluminium followed by reaction and precipitation of the Al4C3 during cooling.

  19. Strengths and limitations of various screening methods for carbapenem-resistant Enterobacteriaceae including new method recommended by clinical and laboratory standards institute, 2017: A tertiary care experience.

    PubMed

    Pragasam, Agila Kumari; Veeraraghavan, Balaji; Bakthavatchalam, Yamuna Devi; Gopi, Radha; Aslam, Raziya Fathima

    2017-01-01

    Carbapenemase-mediated carbapenem resistance is a major concern across the world. Rapid detection of carbapenemase-producing organisms is of great importance in clinical settings. However, it is essential to have a test with good sensitivity and specificity. The aim of the study was to compare the performance of RAPIDEC® CARBA NP and modified carbapenem inactivation method (mCIM) recommended by Clinical and Laboratory Standards Institute guideline 2017. A total of ninety carbapenem resistant Escherichia coli and Klebsiella pneumoniae have been tested. The presence of various carbapenemases was screened by conventional multiplex polymerase chain reaction. RAPIDEC® CARBA NP detected 90%, whereas mCIM detected 99% of the study isolates tested. Although RAPIDEC® CARBA NP is a rapid test, the sensitivity is reduced for blaOxa-48Likedetection; while mCIM could pick up blaOxa-48Likeenzymes with excellent sensitivity. Further, organisms producing low carbapenemase activity enzymes, thickness of the inoculum and the disc potency are likely to influence the test results of mCIM with an overnight delay.

  20. Aluminium uptake and excretion in potroom workers of a new primary aluminium smelter during the construction stage.

    PubMed

    Röllin, H B; Theodorou, P; Nogueir, C M; Levin, J

    2001-12-01

    The aim of this study was to define bio-accumulation and excretion patterns of aluminium in newly employed potroom workers as well as changes in ambient aluminium levels in the potrooms of a modern aluminium smelter during the plant construction stage and one year into full production. A study was carried out on 115 newly employed volunteer potroom workers at various intervals, over a total period of 36 months. Before commencement of employment a structured questionnaire was completed by all study participants and the first collection of blood and urine specimens took place. As none of the subjects had ever worked in the aluminium industry before, they also served as their own controls. Atomic absorption spectroscopy was used to measure the aluminium content in the biological fluids and the content of the metal in the ambient air of the potrooms. Significantly, the study found an early and marked biological response to inhalation of very low levels of airborne aluminium. After only 12 months, the mean concentration of aluminium in serum had almost doubled; thereafter it levelled off. A mixed model analysis did not find any differences in the concentrations of aluminium in the serum of the subjects since the variation between subjects at any given time was much smaller than the variation within subjects. This may be an indication of the pronounced effect of aluminium inhalation on the kinetics of this metal in the human body. Furthermore, urinary excretion of aluminium by the potroom workers showed a linear increase reaching a concentration of only 49 microg l(-1) at the 36 month stage, suggesting a slow rate of elimination.

  1. Investigation and in situ removal of spatter generated during laser ablation of aluminium composites

    NASA Astrophysics Data System (ADS)

    Popescu, A. C.; Delval, C.; Shadman, S.; Leparoux, M.

    2016-08-01

    Spatter generated during laser irradiation of an aluminium alloy nanocomposite (AlMg5 reinforced with Al2O3 nanoparticles) was monitored by high speed imaging. Droplets trajectory and speed were assessed by computerized image analysis. The effects of laser peak power and laser focusing on the plume expansion and expulsed droplet speeds were studied in air or under argon flow. It was found that the velocity of visible droplets expulsed laterally or at the end of the plume emission from the metal surface was not dependent on the plasma plume speed. The neighbouring area of irradiation sites was studied by optical and scanning electron microscopy. Droplets deposited on the surface were classified according to their size and counted using a digital image processing software. It was observed that the number of droplets on surface was 1.5-3 times higher when the laser beam was focused in depth as compared to focused beams, even though the populations average diameter were comparable. Three methods were selected for removing droplets in situ, during plume expansion: an argon gas jet crossing the plasma plume, a fused silica plate collector transparent to the laser wavelength placed parallel to the irradiated surface and a mask placed onto the aluminium composite surface. The argon gas jet was efficient only for low power irradiation conditions, the fused silica plate failed in all tested conditions and the mask was successful for all irradiation regimes.

  2. Production and Compressive Characterization of Aluminium MMC Foam Manufactured Using Dual Foaming Agent

    NASA Astrophysics Data System (ADS)

    Haidar, S.; Ansary, S.; Rahman, A.

    2016-02-01

    Aluminium foams, produced by melting Aluminium alloy (LM6) containing blowing agent(s) and vigorous stirring. TiH2 is a known agent for this. As TiH2 begins to decompose into Ti and gaseous H2 when heated above about 465°C, large volumes of hydrogen gas are rapidly produced, creating bubbles that leads to a closed cell foam. A novel Strategy to enhance the mechanical properties of Al-MMC foams is discussed here, and it is demonstrated that titanium hydride (TiH2) in the form of 10-15 μm diameter particles can be pre-treated by selective oxidation to produce more uniform foams having better compressive properties (yield strength and energy absorption). It is found that the mechanical properties of the foams and the uniformity of cell size distribution is improved when the foam is blown with an optimized mixture of CaCO3 and pretreated TiH2. In order to define the relationship of mechanical properties with relative density of this material, correlations which uniquely defines the compressive behaviour of this modified Al- MMC foam has been developed.

  3. Casting alloys.

    PubMed

    Wataha, John C; Messer, Regina L

    2004-04-01

    Although the role of dental casting alloys has changed in recent years with the development of improved all-ceramic materials and resin-based composites, alloys will likely continue to be critical assets in the treatment of missing and severely damaged teeth. Alloy shave physical, chemical, and biologic properties that exceed other classes of materials. The selection of the appropriate dental casting alloy is paramount to the long-term success of dental prostheses,and the selection process has become complex with the development of many new alloys. However, this selection process is manageable if the practitioner focuses on the appropriate physical and biologic properties, such as tensile strength, modulus of elasticity,corrosion, and biocompatibility, and avoids dwelling on the less important properties of alloy color and short-term cost. The appropriate selection of an alloy helps to ensure a longer-lasting restoration and better oral health for the patient.

  4. Numerical and experimental analysis of cold stretching of aluminium sheets using an instrumented bench

    NASA Astrophysics Data System (ADS)

    El Gueder, Jawhar; Giraud, Eliane; Zhao, Nan; Dal Santo, Philippe

    2016-10-01

    Cold stretching is a forming process meanly used in aeronautic industry to obtain deep drawing parts from thin sheets. It's not very easy to characterize the process using industrial machines, due to production constraints and complexity of their structures. In this study, an instrumented bench is developed to analyse the forming of double curvature panels in 5754H111 Aluminium alloys. A numerical tool using ABAQUS software is developed to predict the behaviour of thin sheets during the stretching process and also to estimate the residual mechanical field in the formed shapes. The bench is calibrated by comparing experiments and numerical results in terms of deformed shape, in-plane strain levels and thickness evolution.

  5. Effect of hydrogen on the integrity of aluminium-oxide interface at elevated temperatures

    NASA Astrophysics Data System (ADS)

    Li, Meng; Xie, De-Gang; Ma, Evan; Li, Ju; Zhang, Xi-Xiang; Shan, Zhi-Wei

    2017-02-01

    Hydrogen can facilitate the detachment of protective oxide layer off metals and alloys. The degradation is usually exacerbated at elevated temperatures in many industrial applications; however, its origin remains poorly understood. Here by heating hydrogenated aluminium inside an environmental transmission electron microscope, we show that hydrogen exposure of just a few minutes can greatly degrade the high temperature integrity of metal-oxide interface. Moreover, there exists a critical temperature of ~150 °C, above which the growth of cavities at the metal-oxide interface reverses to shrinkage, followed by the formation of a few giant cavities. Vacancy supersaturation, activation of a long-range diffusion pathway along the detached interface and the dissociation of hydrogen-vacancy complexes are critical factors affecting this behaviour. These results enrich the understanding of hydrogen-induced interfacial failure at elevated temperatures.

  6. Press hardening of alternative high strength aluminium and ultra-high strength steels

    NASA Astrophysics Data System (ADS)

    Mendiguren, Joseba; Ortubay, Rafael; Agirretxe, Xabier; Galdos, Lander; de Argandoña, Eneko Sáenz

    2016-10-01

    The boron steel press hardening process takes more and more importance on the body in white structure in the last decade. In this work, the advantages of using alternative alloys on the press hardening process is analysed. In particular, the press hardening of AA7075 high strength aluminium and CP800 complex phase ultra-high strength steel is analysed. The objective is to analyse the potential decrease on springback while taking into account the strength change associated with the microstructural modification carried out during the press hardening process. The results show a clear improvement of the final springback in both cases. Regarding the final mechanical properties, an important decrease has been measured in the AA7075 due to the process while an important increase has been found in the CP800 material.

  7. Does allergen-specific immunotherapy induce contact allergy to aluminium?

    PubMed

    Netterlid, Eva; Hindsén, Monica; Siemund, Ingrid; Björk, Jonas; Werner, Sonja; Jacobsson, Helene; Güner, Nuray; Bruze, Magnus

    2013-01-01

    Persistent, itching nodules have been reported to appear at the injection site after allergen-specific immuno-therapy with aluminium-precipitated antigen extract, occasionally in conjunction with contact allergy to aluminium. This study aimed to quantify the development of contact allergy to aluminium during allergen-specific immunotherapy. A randomized, controlled, single-blind multicentre study of children and adults entering allergen-specific immunotherapy was performed using questionnaires and patch-testing. A total of 205 individuals completed the study. In the 3 study groups all subjects tested negative to aluminium before allergen-specific immunotherapy and 4 tested positive after therapy. In the control group 4 participants tested positive to aluminium. Six out of 8 who tested positive also had atopic dermatitis. Positive test results were found in 5/78 children and 3/127 adults. Allergen-specific immunotherapy was not shown to be a risk factor for contact allergy to aluminium. Among those who did develop aluminium allergy, children and those with atopic dermatitis were more highly represented.

  8. The varied functions of aluminium-activated malate transporters–much more than aluminium resistance

    PubMed Central

    Palmer, Antony J.; Baker, Alison; Muench, Stephen P.

    2016-01-01

    The ALMT (aluminium-activated malate transporter) family comprises a functionally diverse but structurally similar group of ion channels. They are found ubiquitously in plant species, expressed throughout different tissues, and located in either the plasma membrane or tonoplast. The first family member identified was TaALMT1, discovered in wheat root tips, which was found to be involved in aluminium resistance by means of malate exudation into the soil. However, since this discovery other family members have been shown to have many other functions such as roles in stomatal opening, general anionic homoeostasis, and in economically valuable traits such as fruit flavour. Recent evidence has also shown that ALMT proteins can act as key molecular actors in GABA (γ-aminobutyric acid) signalling, the first evidence that GABA can act as a signal transducer in plants. PMID:27284052

  9. Aluminium migration into beverages: are dented cans safe?

    PubMed

    Veríssimo, Marta I S; Gomes, M Teresa S R

    2008-11-01

    Aluminium (Al) migration from cans to beer and tea was studied along time. Analyses of Al in the canned drinks were performed till the sell-by date, and, in seven months, aluminium migration was found to increase 0.14 mg L(-1) in beer, and 0.6 mg L(-1) in tea. This study included dented cans from which aluminium migration into tea was found to be particularly severe. Al concentration in dented canned tea increased 9.6 mg L(-1) in seven months.

  10. Aluminium and iron air pollution near an iron casting and aluminium foundry in Turin district (Italy).

    PubMed

    Polizzi, Salvatore; Ferrara, Mauro; Bugiani, Massimiliano; Barbero, Domenico; Baccolo, Tiziana

    2007-09-01

    This work reports the results of an environmental survey carried out in an industrial area in the Province of Turin: its main aim is to assess the levels of iron and aluminium in the outside air during the period from July to September to assess the influence of industrial activity (a cast-iron and aluminium foundry) which is interrupted during the month of August, on the level of metals present in the air. Conducting the analysis during this period of time made it possible to avoid the confounding effect of pollution due to domestic central heating. The measurements were taken from nine areas at different distances from the foundry in the area and according to the direction of the prevailing winds, as deduced from the historical data. The results of this survey show a statistically significant difference in iron and aluminium levels in the outside air in the geographic areas between the two main periods examined: during August (no foundry activity) v/s July-September (foundry activity). The values recorded are: Aluminium 0.4+/-0.45 microg/m(3) v/s 1.12+/-1.29 microg/m(3) (p<0.0001); Iron 0.95+/-0.56 microg/m(3) v/s 1.6+/-1.0 microg/m(3) (p<0.0001). There were no statistically significant differences between the nine sampling points from the point of view of the sampling sites, climate conditions and wind directions. We found no correlation with car traffic, in terms of the number of vehicles, and metals. The values of iron tended to be higher in the areas farther away from the foundry site in the areas located along the path of the prevailing winds.

  11. Development of corrosion resistant aluminum heat exchanger, Part 1: Development of new aluminum alloy sheets for sacrificial anode

    SciTech Connect

    Hagiwara, M.; Baba, Y.; Tanabe, Z.; Miura, T.; Hasegawa, Y.; Iijima, K.

    1986-01-01

    The sacrificial anodic effect of Al-Zn alloy reduced markedly in aluminium heat exchanger as car air conditioner manufactured by vacuum brazing conventionally used, as zinc elements preferentially evaporate in vacuum-heating. It was found that Al-Sn alloy had superior electrochemical characteristics than Al-Zn alloy (AA7072) as the sacrificial anodic material used in vacuum brazing. According to many experimental results, the new brazing sheet-fin with Al-Mn-Sn alloy core metal has been developed. This fin has favorable formability and prominent sacrificial anodic effect. Therefore, this fin is excellent material for car air conditioner manufactured by vacuum brazing.

  12. The Tungsten Inert GAS (TIG) Process of Welding Aluminium in Microgravity: Technical and Economic Considerations

    NASA Astrophysics Data System (ADS)

    Ferretti, S.; Amadori, K.; Boccalatte, A.; Alessandrini, M.; Freddi, A.; Persiani, F.; Poli, G.

    2002-01-01

    The UNIBO team composed of students and professors of the University of Bologna along with technicians and engineers from Alenia Space Division and Siad Italargon Division, took part in the 3rd Student Parabolic Flight Campaign of the European Space Agency in 2000. It won the student competition and went on to take part in the Professional Parabolic Flight Campaign of May 2001. The experiment focused on "dendritic growth in aluminium alloy weldings", and investigated topics related to the welding process of aluminium in microgravity. The purpose of the research is to optimise the process and to define the areas of interest that could be improved by new conceptual designs. The team performed accurate tests in microgravity to determine which phenomena have the greatest impact on the quality of the weldings with respect to penetration, surface roughness and the microstructures that are formed during the solidification. Various parameters were considered in the economic-technical optimisation, such as the type of electrode and its tip angle. Ground and space tests have determined the optimum chemical composition of the electrodes to offer longest life while maintaining the shape of the point. Additionally, the power consumption has been optimised; this offers opportunities for promoting the product to the customer as well as being environmentally friendly. Tests performed on the Al-Li alloys showed a significant influence of some physical phenomena such as the Marangoni effect and thermal diffusion; predictions have been made on the basis of observations of the thermal flux seen in the stereophotos. Space transportation today is a key element in the construction of space stations and future planetary bases, because the volumes available for launch to space are directly related to the payload capacity of rockets or the Space Shuttle. The research performed gives engineers the opportunity to consider completely new concepts for designing structures for space applications

  13. DNA strand patterns on aluminium thin films.

    PubMed

    Khatir, Nadia Mahmoudi; Banihashemian, Seyedeh Maryam; Periasamy, Vengadesh; Majid, Wan Haliza Abd; Rahman, Saadah Abdul; Shahhosseini, Fatemeh

    2011-01-01

    A new patterning method using Deoxyribose Nucleic Acid (DNA) strands capable of producing nanogaps of less than 100 nm is proposed and investigated in this work. DNA strands from Bosenbergia rotunda were used as the fundamental element in patterning DNA on thin films of aluminium (Al) metal without the need for any lithographic techniques. The DNA strands were applied in buffer solutions onto thin films of Al on silicon (Si) and the chemical interactions between the DNA strands and Al creates nanometer scale arbitrary patterning by direct transfer of the DNA strands onto the substrate. This simple and cost-effective method can be utilized in the fabrication of various components in electronic chips for microelectronics and Nano Electronic Mechanical System (NEMS) applications in general.

  14. Telangiectasia in aluminium workers: a follow up.

    PubMed

    Thériault, G; Gingras, S; Provencher, S

    1984-08-01

    A five step investigation was carried out to gain a better understanding of the morbidity that accompanied the development of telangiectasia on aluminium workers and to find its cause. Fifty workers with multiple telangiectasia when matched with normal controls showed the same amount of illness except that evidence of ischaemia on the ECG was found in nine cases and one control. The cases did not show an excess of abnormal biochemical tests. The basic histopathological lesion affected the surrounding tissue rather than the vessels themselves. Working in the current environment and wearing masks seems to protect young workers from developing the lesions. The Soderberg and not the prebake process was associated with the lesions; the causative agent is probably a gas that contains both hydrocarbons and fluoride components emitted from the electrolytic reactors.

  15. A Study of Al-Zn-Sn Alloy Sacrificial Anode Cathodic Protection Requirements for Structure Used In Seawater

    SciTech Connect

    Kamarudin, Siti Radiah Mohd; Daud, Muhamad; Sattar, Shariff; Daud, Abd. Razak

    2010-01-05

    The corrosion of aluminium (Al) alloys in seawater was investigated using potentiodynamic technique, complemented by Scanning Electron Microscopy (SEM), EDAX and XRD. SEM was used out to characterize the corroded surface and to observe the extent of corrosion attack on the Al alloys tested in seawater. EDAX analysis was used to identify elements present on the specimen surface. Where else XRD was to identify phase appearance. The results indicate that zinc (Zn), stanum (Sn) and copper (Cu) as alloying elements enhance corrosion behaviour of the aluminium in seawater by shifting the potential to a more negative value. In the presence of those elements, the Al alloys becomes more active, having potential of more than -1.0 V{sub SCE} and showed active corrosion behaviour.

  16. VANADIUM ALLOYS

    DOEpatents

    Smith, K.F.; Van Thyne, R.J.

    1959-05-12

    This patent deals with vanadium based ternary alloys useful as fuel element jackets. According to the invention the ternary vanadium alloys, prepared in an arc furnace, contain from 2.5 to 15% by weight titanium and from 0.5 to 10% by weight niobium. Characteristics of these alloys are good thermal conductivity, low neutron capture cross section, good corrosion resistance, good welding and fabricating properties, low expansion coefficient, and high strength.

  17. BRAZING ALLOYS

    DOEpatents

    Donnelly, R.G.; Gilliland, R.G.; Slaughter, G.M.

    1963-02-26

    A brazing alloy which, in the molten state, is characterized by excellent wettability and flowability, said alloy being capable of forming a corrosion resistant brazed joint wherein at least one component of said joint is graphite and the other component is a corrosion resistant refractory metal, said alloy consisting essentially of 20 to 50 per cent by weight of gold, 20 to 50 per cent by weight of nickel, and 15 to 45 per cent by weight of molybdenum. (AEC)

  18. Aluminium leaching from red mud by filamentous fungi.

    PubMed

    Urík, Martin; Bujdoš, Marek; Milová-Žiaková, Barbora; Mikušová, Petra; Slovák, Marek; Matúš, Peter

    2015-11-01

    This contribution investigates the efficient and environmentally friendly aluminium leaching from red mud (bauxite residue) by 17 species of filamentous fungi. Bioleaching experiments were examined in batch cultures with the red mud in static, 7-day cultivation. The most efficient fungal strains in aluminium bioleaching were Penicillium crustosum G-140 and Aspergillus niger G-10. The A. niger G-10 strain was capable to extract up to approximately 141 mg·L(-1) of aluminium from 0.2 g dry weight red mud. Chemical leaching with organic acids mixture, prepared according to A. niger G-10 strain's respective fungal excretion during cultivation, proved that organic acids significantly contribute to aluminium solubilization from red mud.

  19. Microstructure Analysis on 6061 Aluminum Alloy after Casting and Diffuses Annealing Process

    NASA Astrophysics Data System (ADS)

    Wang, H. Q.; Sun, W. L.; Xing, Y. Q.

    One factory using semi-continuous casting process produce the ф200×6000 mm 6061 aluminium alloy barstock, and then rotary forged for car wheels. 6061 distorting aluminium alloy is an forged aluminum alloy, and mainly containing Mg, Si, Cu and other alloying elements. The main strengthening phase is Mg2Si, and also has few phase of (FeMn) 3Si2Al15. In order to eliminate the segregation and separation which present in the crystal boundary, and make the distortion to be uniform, and does not present ear and fracture defects after the forging. So the 6061 distorting aluminium alloy adopt the diffusion annealing heat treatment before the forging process.According to the current conditions, we use the diffusion annealing which have the different heating temperature and different holding time.The best process we can obtain from the test which can improve the production efficiency and reduce the material waste, improve the mechanical properties, and eliminate the overheated film on the surface.Then,we using OM,SEM and EDS to analyse the microstructure and the chemical composition of compound between the surface and centre. The result shows that the amount of segregation were different in the surface and in the center, and the different diffusion annealing can cause the phase change in the surface and the center.

  20. Tuning the Hydrogen Storage in Magnesium Alloys

    NASA Astrophysics Data System (ADS)

    Er, Suleyman; de Wijs, Gilles A.; Brocks, Geert

    2011-03-01

    We investigate the hydrogen storage properties of promising magnesium alloys. Mg H2 (7.6 wt % H) would be a very useful storage material if the (de)hydrogenation kinetics can be improved and the desorption temperature is markedly lowered. Using first principles calculations, we show that hydrides of Mg-transition metal (TM) alloys adopt a structure that promotes faster (de)hydrogenation kinetics, as is also observed in experiment. Within the lightweight TMs, the most promising alloying element is titanium. Alloying Mg with Ti alone, however, is not sufficient to decrease the stability of the hydride phases, which is necessary to reduce the hydrogen desorption temperature. We find that adding aluminium or silicon markedly destabilizes Mg-Ti hydrides and stabilizes Mg-Ti alloys. Finally, we show that controlling the structure of Mg-Ti-Al(Si) system by growing it as multilayers, has a beneficial influence on the thermodynamic properties and makes it a stronger candidate for hydrogen storage.

  1. The binding, transport and fate of aluminium in biological cells.

    PubMed

    Exley, Christopher; Mold, Matthew J

    2015-04-01

    Aluminium is the most abundant metal in the Earth's crust and yet, paradoxically, it has no known biological function. Aluminium is biochemically reactive, it is simply that it is not required for any essential process in extant biota. There is evidence neither of element-specific nor evolutionarily conserved aluminium biochemistry. This means that there are no ligands or chaperones which are specific to its transport, there are no transporters or channels to selectively facilitate its passage across membranes, there are no intracellular storage proteins to aid its cellular homeostasis and there are no pathways which evolved to enable the metabolism and excretion of aluminium. Of course, aluminium is found in every compartment of every cell of every organism, from virus through to Man. Herein we have investigated each of the 'silent' pathways and metabolic events which together constitute a form of aluminium homeostasis in biota, identifying and evaluating as far as is possible what is known and, equally importantly, what is unknown about its uptake, transport, storage and excretion.

  2. COS, CS2 and SO 2 in aluminium smelter exhaust : The contribution of aluminium production to the global COS budget.

    PubMed

    Harnisch, J; Borchers, R; Fabian, P

    1995-07-01

    Measurements of carbonyl sulfide (COS) and carbondisulfide (CS2) were carried out on samples drawn from a smoke stack of an aluminium smelter. Volume mixing ratios of 6 ppm COS and 0.1 ppm CS2 were measured for gases from the electrolysis unit that had previously passed an Al2O3 fluid bed reactor and electrostatic precipitators. Specific emissions of 1.6 kg COS and 0.03 kg CS2 per ton of primary aluminium were found. Extrapolating from this particular smelter's conditions to a world mix specific COS emissions of about 4 kg/t(Al) are calculated resulting in emissions of annually 0.08 Tg COS into the atmosphere due to electrolytic aluminium production in 1995. Besides the photochemical conversion of anthropogenic CS2 aluminium production is established to be the second major industrial source of COS probably exceeding automotive tire wear's and coal combustion's contributions.

  3. Electrochemical Codeposition of Al-Li-Mg Alloys at Solid Aluminum Electrode from LiCl-KCl-MgCl2 Molten Salt System

    NASA Astrophysics Data System (ADS)

    Ye, Ke; Zhang, Mi Lin; Chen, Ye; Han, Wei; de Yan, Yong; Cao, Peng

    2010-06-01

    The electrochemical codeposition of Mg and Li at an aluminium electrode in LiCl-KCl (50:50 wt pct) melts containing different concentrations of MgCl2 at 893 K (620 °C) to form Al-Li-Mg alloys was investigated. Cyclic voltammograms showed that the potential of Li metal deposition at an Al electrode, before the addition of MgCl2, is more positive than that of Li metal deposition at an Mo electrode, which indicated the formation of an Al-Li alloy. The underpotential deposition of magnesium at an aluminium electrode leads to the formation of Al-Mg alloys, and the succeeding underpotential deposition of lithium on predeposited Al-Mg alloys leads to the formation of Al-Li-Mg alloys. Chronopotentiometric measurements indicated that the codeposition of Mg and Li occurs at current densities lower than -0.668 A cm-2 in LiCl-KCl-MgCl2 (8 wt pct) melts at an aluminium electrode. The chronoamperometric studies indicated that the onset potential for the codeposition of Mg and Li is -2.000 V, and the codeposition of Mg and Li at an aluminium electrode is formed into Al-Li-Mg alloys when the applied potentials are more negative than -2.000 V. X-ray diffraction and inductively coupled plasma analysis indicated that Al-Li-Mg alloys with different lithium and magnesium contents were prepared via potentiostatic and galvanostatic electrolysis. The microstructure of typical dual phases of the Al-Li-Mg alloy was characterized by an optical microscope and by scanning electron microscopy. The analysis of energy dispersive spectrometry showed that the elements of Al and Mg distribute homogeneously in the Al-Li-Mg alloy. The lithium and magnesium contents of Al-Li-Mg alloys can be controlled by MgCl2 concentrations and by electrolytic parameters.

  4. PILOT EVALUATION OF VANADIUM ALLOYS.

    DTIC Science & Technology

    ARCS, SHEETS, ROLLING(METALLURGY), HIGH TEMPERATURE, SCIENTIFIC RESEARCH, COMPRESSIVE PROPERTIES, DUCTILITY, CREEP, OXIDATION, COATINGS , SILICIDES , HARDNESS, WELDING, EXTRUSION, TANTALUM ALLOYS, MOLYBDENUM ALLOYS....VANADIUM ALLOYS, * NIOBIUM ALLOYS, MECHANICAL PROPERTIES, MECHANICAL PROPERTIES, TITANIUM ALLOYS, ZIRCONIUM ALLOYS, CARBON ALLOYS, MELTING, ELECTRIC

  5. High-rate aluminium yolk-shell nanoparticle anode for Li-ion battery with long cycle life and ultrahigh capacity.

    PubMed

    Li, Sa; Niu, Junjie; Zhao, Yu Cheng; So, Kang Pyo; Wang, Chao; Wang, Chang An; Li, Ju

    2015-08-05

    Alloy-type anodes such as silicon and tin are gaining popularity in rechargeable Li-ion batteries, but their rate/cycling capabilities should be improved. Here by making yolk-shell nanocomposite of aluminium core (30 nm in diameter) and TiO2 shell (∼3 nm in thickness), with a tunable interspace, we achieve 10 C charge/discharge rate with reversible capacity exceeding 650 mAh g(-1) after 500 cycles, with a 3 mg cm(-2) loading. At 1 C, the capacity is approximately 1,200 mAh g(-1) after 500 cycles. Our one-pot synthesis route is simple and industrially scalable. This result may reverse the lagging status of aluminium among high-theoretical-capacity anodes.

  6. High-rate aluminium yolk-shell nanoparticle anode for Li-ion battery with long cycle life and ultrahigh capacity

    PubMed Central

    Li, Sa; Niu, Junjie; Zhao, Yu Cheng; So, Kang Pyo; Wang, Chao; Wang, Chang An; Li, Ju

    2015-01-01

    Alloy-type anodes such as silicon and tin are gaining popularity in rechargeable Li-ion batteries, but their rate/cycling capabilities should be improved. Here by making yolk-shell nanocomposite of aluminium core (30 nm in diameter) and TiO2 shell (∼3 nm in thickness), with a tunable interspace, we achieve 10 C charge/discharge rate with reversible capacity exceeding 650 mAh g−1 after 500 cycles, with a 3 mg cm−2 loading. At 1 C, the capacity is approximately 1,200 mAh g−1 after 500 cycles. Our one-pot synthesis route is simple and industrially scalable. This result may reverse the lagging status of aluminium among high-theoretical-capacity anodes. PMID:26243004

  7. CHIP MORPHOLOGY AND HOLE SURFACE TEXTURE IN THE DRILLING OF CAST ALUMINUM ALLOYS. (R825370C057)

    EPA Science Inventory

    The effects of cutting fluid and other process variables on chip morphology when drilling cast aluminium alloys are investigated. The effects of workpiece material, speed, feed, hole depth, cutting-fluid presence and percentage oil concentration, workpiece temperature, drill t...

  8. Dialysis encephalopathy in a non-dialysed uraemic boy treated with aluminium hydroxide orally.

    PubMed

    Nathan, E; Pedersen, S E

    1980-11-01

    Brain aluminium concentration has been found significantly higher in patients dying with dialysis encephalopathy than in uraemic patients without this syndrome, and it has previously been reported only in haemodialysed patients. We report a case of high brain aluminium concentration in a uraemic boy showing symptoms of severe encephalopathy. He was never dialysed but only treated with aluminium hydroxide orally. Baluarte reported corresponding symptoms in nondialysed uraemic children, but brain aluminium concentrations were not reported. His patients as well as our had very high levels of parathormone which may play a role in the resorption and distribution of aluminium. Aluminium preparations should be avoided in children with renal failure.

  9. Nonswelling alloy

    DOEpatents

    Harkness, S.D.

    1975-12-23

    An aluminum alloy containing one weight percent copper has been found to be resistant to void formation and thus is useful in all nuclear applications which currently use aluminum or other aluminum alloys in reactor positions which are subjected to high neutron doses.

  10. URANIUM ALLOYS

    DOEpatents

    Seybolt, A.U.

    1958-04-15

    Uranium alloys containing from 0.1 to 10% by weight, but preferably at least 5%, of either zirconium, niobium, or molybdenum exhibit highly desirable nuclear and structural properties which may be improved by heating the alloy to about 900 d C for an extended period of time and then rapidly quenching it.

  11. ZIRCONIUM ALLOY

    DOEpatents

    Wilhelm, H.A.; Ames, D.P.

    1959-02-01

    A binary zirconiuin--antimony alloy is presented which is corrosion resistant and hard containing from 0.07% to 1.6% by weight of Sb. The alloys have good corrosion resistance and are useful in building equipment for the chemical industry.

  12. Azide SHS of aluminium nitride nanopowder and its application for obtaining Al-Cu-AlN cast nanocomposite

    NASA Astrophysics Data System (ADS)

    Titova, Y. V.; Sholomova, A. V.; Kuzina, A. A.; Maidan, D. A.; Amosov, A. P.

    2016-11-01

    Method of azide self-propagating high-temperature synthesis (SHS-Az), using sodium azide (NaN3) as a nitriding reagent, was used for obtaining the nanopowder of aluminum nitride (AlN) from precursor that was sodium hexafluoroaluminate (Na3AlF6). The product of burning the mixture of Na3AlF6 + 3NaN3 after water rinsing consisted of micro - and nanoparticles of AlN (65%) and the residue of salt Na3AlF6 (35%). This product of SHS-Az was mixed with copper powder and pressed into a briquette of nanopowdery master alloy Cu- 4%(65%AlN+35%Na3AlF6), which was successfully introduced into aluminium melt at a temperature of 850°C. The salt Na3AlF6 in the product of combustion played a role of flux during introducing into the aluminum melt and was not included in the final composition of the composite alloy. The microstructure of the obtained cast composite aluminum alloy with the calculated composition of Al-1.2%Cu-0.035%AlN showed that the reinforcing particles of AlN of different sizes, including nanoparticles, were distributed mainly along the grain boundaries of the aluminum alloy.

  13. Accumulation and toxicity of aluminium-contaminated food in the freshwater crayfish, Pacifastacus leniusculus.

    PubMed

    Woodburn, Katie; Walton, Rachel; McCrohan, Catherine; White, Keith

    2011-10-01

    The accumulation and toxicity of aluminium in freshwater organisms have primarily been examined following aqueous exposure. This study investigated the uptake, excretion and toxicity of aluminium when presented as aluminium-contaminated food. Adult Pacifastacus leniusculus were fed control (3 μg aluminium/g) or aluminium-spiked pellets (420 μg aluminium/g) over 28 days. Half the crayfish in each group were then killed and the remainder fed control pellets for a further 10 days (clearance period). Concentrations of aluminium plus the essential metals calcium, copper, potassium and sodium were measured in the gill, hepatopancreas, flexor muscle, antennal gland (kidney) and haemolymph. Histopathological analysis of tissue damage and sub-cellular distribution of aluminium were examined in the hepatopancreas. Haemocyte number and protein concentration in the haemolymph were analysed as indicators of toxicity. The hepatopancreas of aluminium-fed crayfish contained significantly more aluminium than controls on days 28 and 38, and this amount was positively correlated with the amount ingested. More than 50% of the aluminium in the hepatopancreas of aluminium-fed crayfish was located in sub-cellular fractions thought to be involved in metal detoxification. Aluminium concentrations were also high in the antennal glands of aluminium-fed crayfish suggesting that some of the aluminium lost from the hepatopancreas is excreted. Aluminium exposure via contaminated food caused inflammation in the hepatopancreas but did not affect the number of circulating haemocytes, haemolymph ion concentrations or protein levels. In conclusion, crayfish accumulate, store and excrete aluminium from contaminated food with only localised toxicity.

  14. A Numerical Simulation for Dissimilar Aluminum Alloys Joined by Friction Stir Welding

    NASA Astrophysics Data System (ADS)

    Hamilton, Carter; Kopyściański, Mateusz; Węglowska, Aleksandra; Dymek, Stanisław; Pietras, Adam

    2016-09-01

    Dissimilar aluminum alloy sheets of 2017A-T451 and 7075-T651 (6 mm thickness) were friction stir welded in a butt weld configuration. A numerical simulation of the joining process was developed to visualize the material flow patterns and temperature distribution and to correlate the microstructure to the hardness behavior. Due to the complementary downward flow of surface material into the workpiece thickness and upward flow of mid-plane and bottom-plane material, the weld nugget is composed of alternating layers of 7075 and 2017A. These layers have unique temperature histories depending on the material's initial location within the cross section; therefore, they also have distinctive precipitate distributions. Supersaturated surface material flows into the process zone and forms a core in which GP zones reprecipitate upon cooling. Mid-plane and bottom-plane material flow toward the workpiece surface and encompass the surface material core. Within this region, the weld temperatures overage the equilibrium θ phase in 2017A, decreasing the hardness, and at the same time, dissolve the equilibrium η/ T phase in the 7075, leading to reprecipitation of GP zones upon cooling and a hardness recovery.

  15. The influence of laser alloying on the structure and mechanical properties of AlMg5Si2Mn surface layers

    NASA Astrophysics Data System (ADS)

    Pakieła, W.; Tański, T.; Brytan, Z.; Labisz, K.

    2016-04-01

    The goal of this paper was focused on investigation of microstructure and properties of surface layer produced during laser surface treatment of aluminium alloy by high-power fibre laser. The performed laser treatment involves remelting and feeding of Inconel 625 powder into the aluminium surface. As a base metal was used aluminium alloy AlMg5Si2Mn. The Inconel powder was injected into the melt pool and delivered by a vacuum feeder at a constant rate of 4.5 g/min. The size of Inconel alloying powder was in the range 60-130 µm. In order to remelt the aluminium alloy surface, the fibre laser of 3 kW laser beam power has been used. The linear laser scan rate of the beam was set 0.5 m/min. Based on performed investigations, it was possible to obtain the layer consisting of heat-affected zone, transition zone and remelted zone, without cracks and defects having much higher hardness value compared to the non-alloyed material.

  16. Fuzzy Multicriteria Ranking of Aluminium Coating Methods

    NASA Astrophysics Data System (ADS)

    Batzias, A. F.

    2007-12-01

    This work deals with multicriteria ranking of aluminium coating methods. The alternatives used are: sulfuric acid anodization, A1; oxalic acid anodization, A2; chromic acid anodization, A3; phosphoric acid anodization, A4; integral color anodizing, A5; chemical conversion coating, A6; electrostatic powder deposition, A7. The criteria used are: cost of production, f1; environmental friendliness of production process, f2; appearance (texture), f3; reflectivity, f4; response to coloring, f5; corrosion resistance, f6; abrasion resistance, f7; fatigue resistance, f8. Five experts coming from relevant industrial units set grades to the criteria vector and the preference matrix according to a properly modified Delphi method. Sensitivity analysis of the ranked first alternative A1 against the `second best', which was A3 at low and A7 at high resolution levels proved that the solution is robust. The dependence of anodized products quality on upstream processes is presented and the impact of energy price increase on industrial cost is discussed.

  17. Corrosion of aluminium in soft drinks.

    PubMed

    Seruga, M; Hasenay, D

    1996-04-01

    The corrosion of aluminium (Al) in several brands of soft drinks (cola- and citrate-based drinks) has been studied, using an electrochemical method, namely potentiodynamic polarization. The results show that the corrosion of Al in soft drinks is a very slow, time-dependent and complex process, strongly influenced by the passivation, complexation and adsorption processes. The corrosion of Al in these drinks occurs principally due to the presence of acids: citric acid in citrate-based drinks and orthophosphoric acid in cola-based drinks. The corrosion rate of Al rose with an increase in the acidity of soft drinks, i.e. with increase of the content of total acids. The corrosion rates are much higher in the cola-based drinks than those in citrate-based drinks, due to the facts that: (1) orthophosphoric acid is more corrosive to Al than is citric acid, (2) a quite different passive oxide layer (with different properties) is formed on Al, depending on whether the drink is cola or citrate based. The method of potentiodynamic polarization was shown as being very suitable for the study of corrosion of Al in soft drinks, especially if it is combined with some non-electrochemical method, e.g. graphite furnace atomic absorption spectrometry (GFAAS).

  18. PLUTONIUM ALLOYS

    DOEpatents

    Chynoweth, W.

    1959-06-16

    The preparation of low-melting-point plutonium alloys is described. In a MgO crucible Pu is placed on top of the lighter alloying metal (Fe, Co, or Ni) and the temperature raised to 1000 or 1200 deg C. Upon cooling, the alloy slug is broke out of the crucible. With 14 at. % Ni the m.p. is 465 deg C; with 9.5 at. % Fe the m.p. is 410 deg C; and with 12.0 at. % Co the m.p. is 405 deg C. (T.R.H.) l6262 l6263 ((((((((Abstract unscannable))))))))

  19. Aluminum alloy

    NASA Technical Reports Server (NTRS)

    Blackburn, Linda B. (Inventor); Starke, Edgar A., Jr. (Inventor)

    1989-01-01

    This invention relates to aluminum alloys, particularly to aluminum-copper-lithium alloys containing at least about 0.1 percent by weight of indium as an essential component, which are suitable for applications in aircraft and aerospace vehicles. At least about 0.1 percent by weight of indium is added as an essential component to an alloy which precipitates a T1 phase (Al2CuLi). This addition enhances the nucleation of the precipitate T1 phase, producing a microstructure which provides excellent strength as indicated by Rockwell hardness values and confirmed by standard tensile tests.

  20. Corrosion of aluminium metal in OPC- and CAC-based cement matrices

    SciTech Connect

    Kinoshita, Hajime; Swift, Paul; Utton, Claire; Carro-Mateo, Beatriz; Collier, Nick; Milestone, Neil

    2013-08-15

    Corrosion of aluminium metal in ordinary Portland cement (OPC) based pastes produces hydrogen gas and expansive reaction products causing problems for the encapsulation of aluminium containing nuclear wastes. Although corrosion of aluminium in cements has been long known, the extent of aluminium corrosion in the cement matrices and effects of such reaction on the cement phases are not well established. The present study investigates the corrosion reaction of aluminium in OPC, OPC-blast furnace slag (BFS) and calcium aluminate cement (CAC) based systems. The total amount of aluminium able to corrode in an OPC and 4:1 BFS:OPC system was determined, and the correlation between the amount of calcium hydroxide in the system and the reaction of aluminium obtained. It was also shown that a CAC-based system could offer a potential matrix to incorporate aluminium metal with a further reduction of pH by introduction of phosphate, producing a calcium phosphate cement.

  1. Aluminium recycling and environmental issues of salt slag treatment.

    PubMed

    Xiao, Yanping; Reuter, Markus A; Boin, Udo

    2005-01-01

    Environmental friendly recycling is the trend toward total recycling of aluminium metal. In the secondary aluminium industry, due to the complexity of compositions and contaminants in the various types of aluminium scraps, an understanding of the behavior of different scraps during melting is crucial in the recycling process. Salt slags are the byproducts of the secondary aluminium industry, which should be recycled and processed in a proper way by taking the environmental impact into consideration. This article provides qualitative assessment on 10 different commercial aluminium scraps for their relative recyclability via well-designed and controlled laboratory experiments. It confirms that more nonmetallic contaminants, smaller size, and higher ratio of surface area to body volume generally lead to a lower metal recovery. Recycling the scraps with lower recyclability normally generates more salt slags. High slag viscosity leads to more fine aluminum metal entrapped in the salt slag and thus increases the load of salt slag recycling. It was found that viscosity of the salt flux is increased with the amount of entrapped nonmetallic components, which affect the settling of heavier materials. In addition, the slag samples from the melting tests were leached and analyzed to evaluate the behavior of carbon containing scrap. The elevated carbon content in the scrap resulted in more carbide formation in salt slags and thus more methane generation in salt slag recycling with a higher environmental impact.

  2. Improving Efficiency of Aluminium Sacrificial Anode Using Cold Work Process

    NASA Astrophysics Data System (ADS)

    Asmara, Y. P.; Siregar, J. P.; Tezara, C.; Ann, Chang Tai

    2016-02-01

    Aluminium is one of the preferred materials to be used as sacrificial anode for carbon steel protection. The efficiency of these can be low due to the formation of oxide layer which passivate the anodes. Currently, to improve its efficiency, there are efforts using a new technique called surface modifications. The objective of this research is to study corrosion mechanism of aluminium sacrificial anode which has been processed by cold work. The cold works are applied by reducing the thickness of aluminium sacrificial anodes at 20% and 40% of thickness reduction. The cathodic protection experiments were performed by immersion of aluminium connected to carbon steel cylinder in 3% NaCl solutions. Visual inspections using SEM had been conducted during the experiments and corrosion rate data were taken in every week for 8 weeks of immersion time. Corrosion rate data were measured using weight loss and linear polarization technique (LPR). From the results, it is observed that cold worked aluminium sacrificial anode have a better corrosion performance. It shows higher corrosion rate and lower corrosion potential. The anodes also provided a long functional for sacrificial anode before it stop working. From SEM investigation, it is shown that cold works have changed the microstructure of anodes which is suspected in increasing corrosion rate and cause de-passivate of the surface anodes.

  3. Removal of chelated aluminium during haemodialysis using polysulphone high-flux dialysers.

    PubMed

    Aarseth, H P; Ganss, R

    1990-01-01

    Polysulphone high-flux dialysers were used for removal of chelated aluminium in desferrioxamine-treated patients on maintenance haemodialysis. When compared with charcoal haemoperfusion in series with a cuprophane dialyser, the same aluminium clearance was obtained (34% of blood flow). During 4 h of haemodialysis serum aluminium was reduced to the concentration seen before desferrioxamine infusion. We conclude that high-flux polysulphone dialysers remove chelated aluminium as efficiently as does charcoal haemoperfusion, and at a lower cost.

  4. Segregation phenomena at growing alumina/alloy interfaces

    SciTech Connect

    Hou, Peggy Y.

    2005-03-30

    The chemistry and structure at the scale/alloy interface are important factors governing scale adhesion. The chemical changes can occur from segregation of impurities in the alloy, such as sulphur and carbon, or alloying elements such as chromium, aluminium and reactive elements. This paper reviews studies of the changes of interfacial composition with oxidation time for Al{sub 2}O{sub 3} formed on several model alumina-forming alloys, and tries to relate that to the interfacial strength. Results show that sulphur segregation to oxide/metal interfaces can indeed occur, but the type and amount of segregants at the interface depend on the alloy composition and the interface structure. Co-segregation of impurities with alloying elements can also occur, resulting in multi-layer segregants at the interface. Sulphur-containing interfaces are indeed weaker, but the major role of sulphur is to enhance interfacial void formation. Reactive elements in the alloy not only gather sulfur but also exert an additional positive effect on scale adhesion.

  5. Formability Analysis of Magnesium Alloy Sheet Bulging Using FE Simulation

    SciTech Connect

    Mac Donald, B. J.; Hunt, D.; Yoshihara, S.; Manabe, K.

    2007-05-17

    There is currently much focus on the application of magnesium alloys to automotive structural components. This has arisen due to the positive environmental aspects associated with use of magnesium alloys such as weight reduction and recycling potential. In recent years many researchers have focused on the application of various forming processes to magnesium alloys. Magnesium alloys would seem highly suitable for sheet forming due to high N and r values, however, in application their formability has been inferior to, for example, aluminium alloys. It has thus been concluded that, when dealing with magnesium alloys, it is difficult to predict formability based on material properties. In order to improve formability and forming accuracy when using Mg alloys it is necessary to build a database and inference system which could decide the optimal forming parameters for complex automotive components. Currently not enough data is available to build such a database due to the limited number of studies available in literature. In this study an experimental analysis of hemispherical bulge forming at elevated temperature was undertaken in order to evaluate formability and hence build a database for forming process design. A finite element model based on the experiment has been built and validated against the experimental results. A ductile failure criterion has been integrated with the FE model and is used to predict the onset of failure. This paper discusses the development and validation of the finite element model with the ductile failure criterion and presents results from the experimental tests and FE simulations.

  6. In situ observation and analysis of ultrasonic capillary effect in molten aluminium.

    PubMed

    Tzanakis, I; Xu, W W; Eskin, D G; Lee, P D; Kotsovinos, N

    2015-11-01

    An in situ synchrotron radiographic study of a molten Al-10 wt% Cu alloy under the influence of an external ultrasonic field was carried out using the Diamond-Manchester Branchline pink X-ray imaging at the Diamond Light Source in UK. A bespoke test rig was used, consisting of an acoustic transducer with a titanium sonotrode coupled with a PID-controlled resistance furnace. An ultrasonic frequency of 30 kHz, with a peak to peak amplitude at 140 microns, was used, producing a pressure output of 16.9 MPa at the radiation surface of the 1-mm diameter sonotrode. This allowed quantification of not only the cavitation bubble formation and collapse, but there was also evidence of the previously hypothesised ultrasonic capillary effect (UCE), providing the first direct observations of this phenomenon in a molten metallic alloy. This was achieved by quantifying the re-filling of a pre-existing groove in the shape of a tube (which acted as a micro-capillary channel) formed by the oxide envelope of the liquid sample. Analytical solutions of the flow suggest that the filling process, which took place in very small timescales, was related to micro-jetting from the collapsing cavitation bubbles. In addition, a secondary mechanism of liquid penetration through the groove, which is related with the density distribution of the oxides inside the groove, and practically to the filtration of aluminium melt from oxides, was revealed. The observation of the almost instantaneous re-filling of a micro-capillary channel with the metallic melt supports the hypothesised sono-capillary effect in technologically important liquids other than water, like metallic alloys with substantially higher surface tension and density.

  7. Determination of aluminium in groundwater samples by GF-AAS, ICP-AES, ICP-MS and modelling of inorganic aluminium complexes.

    PubMed

    Frankowski, Marcin; Zioła-Frankowska, Anetta; Kurzyca, Iwona; Novotný, Karel; Vaculovič, Tomas; Kanický, Viktor; Siepak, Marcin; Siepak, Jerzy

    2011-11-01

    The paper presents the results of aluminium determinations in ground water samples of the Miocene aquifer from the area of the city of Poznań (Poland). The determined aluminium content amounted from <0.0001 to 752.7 μg L(-1). The aluminium determinations were performed using three analytical techniques: graphite furnace atomic absorption spectrometry (GF-AAS), inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). The results of aluminium determinations in groundwater samples for particular analytical techniques were compared. The results were used to identify the ascent of ground water from the Mesozoic aquifer to the Miocene aquifer in the area of the fault graben. Using the Mineql+ program, the modelling of the occurrence of aluminium and the following aluminium complexes: hydroxy, with fluorides and sulphates was performed. The paper presents the results of aluminium determinations in ground water using different analytical techniques as well as the chemical modelling in the Mineql+ program, which was performed for the first time and which enabled the identification of aluminium complexes in the investigated samples. The study confirms the occurrence of aluminium hydroxy complexes and aluminium fluoride complexes in the analysed groundwater samples. Despite the dominance of sulphates and organic matter in the sample, major participation of the complexes with these ligands was not stated based on the modelling.

  8. BRAZING ALLOYS

    DOEpatents

    Donnelly, R.G.; Gilliland, R.G.; Slaughter, G.M.

    1962-02-20

    A brazing alloy is described which, in the molten state, is characterized by excellent wettability and flowability and is capable of forming a corrosion-resistant brazed joint. At least one component of said joint is graphite and the other component is a corrosion-resistant refractory metal. The brazing alloy consists essentially of 40 to 90 wt % of gold, 5 to 35 wt% of nickel, and 1 to 45 wt% of tantalum. (AEC)

  9. COATED ALLOYS

    DOEpatents

    Harman, C.G.; O'Bannon, L.S.

    1958-07-15

    A coating is described for iron group metals and alloys, that is particularly suitable for use with nickel containing alloys. The coating is glassy in nature and consists of a mixture containing an alkali metal oxide, strontium oxide, and silicon oxide. When the glass coated nickel base metal is"fired'' at less than the melting point of the coating, it appears the nlckel diffuses into the vitreous coating, thus providing a closely adherent and protective cladding.

  10. Computer Modelling of Age Hardening for Isothermally Aged Al-Mg-Si Alloys

    NASA Astrophysics Data System (ADS)

    Wu, Linda; Ferguson, W. George

    Computer modelling, due to it saving time and money, has been widely used in industrial simulation. The present model, which is based on the Shercliff-Ashby methodology for the ageing of aluminum alloys, can be used to predict the yield strength (or hardness) of Al-Mg-Si alloys for the artificial ageing temperature below the solvus temperature as a function of time. With suitable input data, this model can be applied to most Al-Mg-Si alloys, wrought or cast. In the present model, input data for aluminium alloys of A356, A357 and 6061 is taken from the open literature, and then the unknown constants are calibrated from these data. After calibration, the ageing curves are constructed for different isothermal ageing temperatures. Finally, experimentally ageing heat treatments at different temperatures for casting alloys of A356 were done to validate the model.

  11. Synthesis and characterization of a new aluminium-based compound.

    PubMed

    Pascual-Cosp, José; Artiaga, Ramón; Corpas-Iglesias, Francisco; Benítez-Guerrero, Mónica

    2009-08-28

    A new aluminium polynuclear crystalline species, Al(13)(OH)(30)(H(2)O)(15)Cl(9) has been synthesized and characterized. It is a particular case of the Al(13)(OH)(30-y)(H(2)O)(18-x)Cl(9) x zH(2)O family. It has been obtained from aluminium waste cans treated with HCl solution in strong acid media, followed by an ageing period. The crystalline structure of the complex was determined by XRD spectroscopy. Twelve reflections were found and indexed with the DICVOL04 software. Morphologically, a flattened preferred orientation was observed by SEM and FESEM. The chemical structure was studied by several absorption spectroscopy techniques: FTIR, ATR-FTIR and Raman dispersion spectroscopy. The coordination of the aluminium nuclei was determined by Al-MAS-NMR. Only octahedral sites were observed. Thermal characterization of the compound was performed by evolved gas analysis (EGA) coupled to simultaneous TGA-DSC.

  12. Coal fly ash: a potential resource for aluminium and titanium

    SciTech Connect

    Frederick, J.R.; Murtha, M.J.; Burnet, G.

    1980-01-01

    Two processes are described which utilize fly ash as a source of metals and by-products. The lime-soda sinter process involves sintering of the fly ash and alkaline oxides at 1100-1300/sup 0/C to break the alumina-silica bonds and form soluble aluminate compounds and insoluble calcium silicates. The aluminates are extracted from the sinter by dissolution in sodium carbonate. The calcium silicate sinter extract shows promise as a raw material for the manufacture of portland cement. The HiChlor process uses high temperature chlorination of fly ash in the presence of a reductant to form volatile metal chlorides of aluminium, titanium, iron, and silicon. The HiChlor process extracts aluminium, titanium, and iron, while the sinter process extracts only aluminium.

  13. Different Approach to the Aluminium Oxide Topography Characterisation

    SciTech Connect

    Poljacek, Sanja Mahovic; Gojo, Miroslav; Raos, Pero; Stoic, Antun

    2007-04-07

    Different surface topographic techniques are being widely used for quantitative measurements of typical industrial aluminium oxide surfaces. In this research, specific surface of aluminium oxide layer on the offset printing plate has been investigated by using measuring methods which have previously not been used for characterisation of such surfaces. By using two contact instruments and non-contact laser profilometer (LPM) 2D and 3D roughness parameters have been defined. SEM micrographs of the samples were made. Results have shown that aluminium oxide surfaces with the same average roughness value (Ra) and mean roughness depth (Rz) typically used in the printing plate surface characterisation, have dramatically different surface topographies. According to the type of instrument specific roughness parameters should be used for defining the printing plate surfaces. New surface roughness parameters were defined in order to insure detailed characterisation of the printing plates in graphic reproduction process.

  14. Aluminium toxicity in the rat liver and brain

    NASA Astrophysics Data System (ADS)

    Yumoto, S.; Ohashi, H.; Nagai, H.; Kakimi, S.; Ishikawa, A.; Kobayashi, K.; Ogawa, Y.; Ishii, K.

    1993-04-01

    To investigate the etiology of Alzheimer's disease, we examined the brain and liver tissue uptake of aluminium 5-75 days after aluminium injection into healthy rats. Ten days after the last injection, Al was detected in the brain and the brain cell nuclei by particle-induced X-ray emission (PIXE) analysis. Al was also demonstrated in the liver and the liver cell nuclei by PIXE analysis and electron energy loss spectrometry (EELS). The morphological changes of the rat brain examined 75 days after the injection were similar to those which have been reportedly observed in the brain of patients with Alzheimer's disease. These results support the theory that Alzheimer's disease is caused by irreversible accumulation of aluminium in the brain, as well as in the nuclei of brain cells.

  15. [Photophysical properties and photodynamic activity of nanostructured aluminium phthalocyanines].

    PubMed

    Udartseva, O O; Lobanov, A V; Andeeva, E R; Dmitrieva, G S; Mel'nikov, M Ia; Buravkova, L B

    2014-01-01

    We developed water-soluble supramolecular complexes of aluminium phthalocyanine based on mesoporous silica nanoparticles and polyvinylpirrolidone containing rare photoactive nanoaggregates. Radiative lifetimes, extinction coefficients and energy of electronic transitions of isolated and associated metal phthalocyanine complexes were calculated. Nontoxic concentrations of synthesized nanocomposite photosensibilizers were in vitro determined. In present study we compared photodynamic treatment efficacy using different modifications of aluminium phthalocyanine (Photosens®, AlPc-nSiO2 and AlPc-PVP). Mesenchymal stromal cells were used as a model for photodynamic treatment. Intracellular accumulation of aluminium phthalocyanine based on mesoporous silica nanoparticles AlPc-nSiO2 was the most efficient. Illumination of phthalocyanine-loaded cells led to reactive oxygen species generation and subsequent apoptotic cell death. Silica nanoparticles provided a significant decrease of effective phthalocyanine concentration and enhanced cytotoxicity of photodynamic treatment.

  16. Surface chemical studies of anodically oxidised aluminium membranes

    NASA Astrophysics Data System (ADS)

    Treverton, J. A.; West, R.; Johnson, D.; Thornton, M.

    1993-12-01

    X-ray photoelectron spectroscopy (XPS) and fast atom bombardment secondary ion mass spectrometry (FAB-SIMS) have been used to study the surfaces of inorganic microfiltration membranes produced by controlled removal of anodic films formed on aluminium in phosphoric and oxalic acid electrolytes. The results are compared with those of similar analyses of membranes produced from anodic films formed in mixed oxalic/phosphoric acid electrolyte. Both techniques established that phosphates were concentrated on the surface of membranes formed in phosphoric acid and oxalic/phosphoric acid and that oxalate ions were present on the surfaces of membranes formed in oxalic acid. The low intensity of the AlO -x fragments implies that all of the aluminium ions in the surface are coordinated to phosphates or oxalates. However, any differences its the chemical state of the aluminium on the different membranes were not detectable by either technique.

  17. The immunobiology of aluminium adjuvants: how do they really work?

    PubMed

    Exley, Christopher; Siesjö, Peter; Eriksson, Håkan

    2010-03-01

    Aluminium adjuvants potentiate the immune response, thereby ensuring the potency and efficacy of typically sparingly available antigen. Their concomitant critical importance in mass vaccination programmes may have prompted recent intense interest in understanding how they work and their safety. Progress in these areas is stymied, however, by a lack of accessible knowledge pertaining to the bioinorganic chemistry of aluminium adjuvants, and, consequently, the inappropriate application and interpretation of experimental models of their mode of action. The objective herein is, therefore, to identify the many ways that aluminium chemistry contributes to the wide and versatile armoury of its adjuvants, such that future research might be guided towards a fuller understanding of their role in human vaccinations.

  18. Airway inflammation in aluminium potroom asthma

    PubMed Central

    Sjaheim, T; Halstensen, T; Lund, M; Bjortuft, O; Drablos, P; Malterud, D; Kongerud, J

    2004-01-01

    Aims: To examine whether asthma induced by exposure to aluminium potroom emissions (potroom asthma) is associated with inflammatory changes in the airways. Methods: Bronchial biopsy specimens from 20 asthmatic workers (8 non-smokers and 12 smokers), 15 healthy workers (8 non-smokers and 7 smokers), and 10 non-exposed controls (all non-smokers) were analysed. Immunohistofluorescent staining was performed to identify mucosal total leucocytes (CD45+ leucocytes), neutrophils, and mast cells. Results: Median RBM thickness was significantly increased in both asthmatic workers (8.2 µm) and healthy workers (7.4 µm) compared to non-exposed controls (6.7 µm). Non-smoking asthmatic workers had significantly increased median density of lamina propria CD45+ leucocytes (1519 cells/mm2v 660 and 887 cells/mm2) and eosinophils (27 cells/mm2v 10 and 3 cells/mm2) and significantly increased concentrations of exhaled NO (18.1 ppb v 6.5 and 5.1 ppb) compared to non-smoking healthy workers and non-exposed controls. Leucocyte counts and exhaled NO concentrations varied with smoking habits and fewer leucocytes were observed in asthmatic smokers than in non-smokers Asthmatic smokers had significantly increased numbers of eosinophils in lamina propria compared to non-exposed controls (10 v 3 cells/mm2). Both eosinophilic and non-eosinophilic phenotypes of asthma were recognised in the potroom workers and signs of airway inflammation were also observed in healthy workers. Conclusions: Airway inflammation is a central feature of potroom asthma and exposure to potroom emissions induces pathological alterations similar to those described in other types of asthma. Cigarette smoking seems to affect the underlying mechanisms involved in asthma, as the cellular composition of airway mucosa appears different in asthmatic smokers and non-smokers. PMID:15317920

  19. Stimulation of eryptosis by aluminium ions

    SciTech Connect

    Niemoeller, Olivier M.; Kiedaisch, Valentin; Dreischer, Peter; Wieder, Thomas; Lang, Florian . E-mail: florian.lang@uni-tuebingen.de

    2006-12-01

    Aluminium salts are utilized to impede intestinal phosphate absorption in chronic renal failure. Toxic side effects include anemia, which could result from impaired formation or accelerated clearance of circulating erythrocytes. Erythrocytes may be cleared secondary to suicidal erythrocyte death or eryptosis, which is characterized by cell shrinkage and exposure of phosphatidylserine (PS) at the erythrocyte surface. As macrophages are equipped with PS receptors, they bind, engulf and degrade PS-exposing cells. The present experiments have been performed to explore whether Al{sup 3+} ions trigger eryptosis. The PS exposure was estimated from annexin binding and cell volume from forward scatter in FACS analysis. Exposure to Al{sup 3+} ions ({>=} 10 {mu}M Al{sup 3+} for 24 h) indeed significantly increased annexin binding, an effect paralleled by decrease of forward scatter at higher concentrations ({>=} 30 {mu}M Al{sup 3+}). According to Fluo3 fluorescence Al{sup 3+} ions ({>=} 30 {mu}M for 3 h) increased cytosolic Ca{sup 2+} activity. Al{sup 3+} ions ({>=} 10 {mu}M for 24 h) further decreased cytosolic ATP concentrations. Energy depletion by removal of glucose similarly triggered annexin binding, an effect not further enhanced by Al{sup 3+} ions. The eryptosis was paralleled by release of hemoglobin, pointing to loss of cell membrane integrity. In conclusion, Al{sup 3+} ions decrease cytosolic ATP leading to activation of Ca{sup 2+}-permeable cation channels, Ca{sup 2+} entry, stimulation of cell membrane scrambling and cell shrinkage. Moreover, Al{sup 3+} ions lead to loss of cellular hemoglobin, a feature of hemolysis. Both effects are expected to decrease the life span of circulating erythrocytes and presumably contribute to the development of anemia during Al{sup 3+} intoxication.

  20. Characterisation of Ga-coated and Ga-brazed aluminium

    SciTech Connect

    Ferchaud, E.; Christien, F.; Barnier, V.; Paillard, P.

    2012-05-15

    This work is devoted to the brazing of aluminium using liquid gallium. Gallium was deposited on aluminium samples at {approx} 50 Degree-Sign C using a liquid gallium 'polishing' technique. Brazing was undertaken for 30 min at 500 Degree-Sign C in air. EDS (Energy Dispersive X-ray Spectroscopy) and AES (Auger Electron Spectroscopy) characterisation of Ga-coated samples has shown that the Ga surface layer thickness is of ten (or a few tens of) nanometres. Furthermore, aluminium oxide layer (Al{sub 2}O{sub 3}) was shown to be 'descaled' during Ga deposition, which ensures good conditions for further brazing. Cross-section examination of Ga-coated samples shows that liquid gallium penetrates into the aluminium grain boundaries during deposition. The thickness of the grain boundary gallium film was measured using an original EDS technique and is found to be of a few tens of nanometres. The depth of gallium grain boundary penetration is about 300 {mu}m at the deposition temperature. The fracture stress of the brazed joints was measured from tensile tests and was determined to be 33 MPa. Cross-section examination of brazed joints shows that gallium has fully dissolved into the bulk and that the joint is really autogenous. - Highlights: Black-Right-Pointing-Pointer Aluminium can be brazed using liquid gallium deposited by a 'polishing' technique. Black-Right-Pointing-Pointer The aluminium oxide layer is 'descaled' during liquid Ga 'polishing' deposition. Black-Right-Pointing-Pointer EDS can be used for determination of surface and grain boundary Ga film thickness. Black-Right-Pointing-Pointer The surface and grain boundary Ga film thickness is of a few tens of nm. Black-Right-Pointing-Pointer Surface and grain boundary gallium dissolves in the bulk during brazing.

  1. Silver coated aluminium microrods as highly colloidal stable SERS platforms.

    PubMed

    Pazos-Perez, Nicolas; Borke, Tina; Andreeva, Daria V; Alvarez-Puebla, Ramon A

    2011-08-01

    We report on the fabrication of a novel material with the ability to remain in solution even under the very demanding conditions required for structural and dynamic characterization of biomacromolecule assays. This stability is provided by the increase in surface area of a low density material (aluminium) natively coated with a very hydrophilic surface composed of aluminium oxide (Al(2)O(3)) and metallic silver nanoparticles. Additionally, due to the dense collection of active hot spots on their surface, this material offers higher levels of SERS intensity as compared with the same free and aggregated silver nanoparticles.

  2. Transmittance jump in a thin aluminium layer during laser ablation

    SciTech Connect

    Bykovsky, N E; Senatsky, Yu V; Pershin, S M; Samokhin, A A

    2016-02-28

    A jump in the transmittance (from ∼0.1% to ∼50% for ∼1 ns) of an optical gate on a Mylar film (a thin aluminium layer on a Lavsan substrate) irradiated by nanosecond (10{sup -7} – 10{sup -8} s) pulses of a neodymium laser with an intensity up to 0.1 GW cm{sup -2} has been recorded. The mechanism of a fast (10{sup -10} – 10{sup -11} s) increase in the transmittance of the aluminium layer upon its overheating (without boiling) to the metal – insulator phase-transition temperature is discussed. (interaction of laser radiation with matter. laser plasma)

  3. Microstructural, mechanical and electrochemical behaviour of a 7017 Al–Zn–Mg alloy of different tempers

    SciTech Connect

    Rout, Prasanta Kumar Ghosh, M.M.; Ghosh, K.S.

    2015-06-15

    The aim of the investigation is to assess the microstructural features and associated physical, mechanical and electrochemical properties of a 7017 Al–Zn–Mg alloy of various tempers. A 7017 Al–Zn–Mg alloy was subjected to different ageing schedules to produce under-(T4), peak-(T6), over-(T7) and highly over-aged tempers. Optical microscopy, hardness measurement, electrical conductivity measurement, tensile testing and SEM fractographs, differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and electrochemical polarization studies have been used to characterize the alloy tempers. Hardness measurement and tensile testing showed the characteristic age hardening phenomenon of aluminium alloys. Optical and TEM micrographs have revealed the variation in size of matrix strengthening η′ (MgZn{sub 2}) and also the size and distribution of grain boundary η (MgZn{sub 2}) precipitate with ageing time. DSC thermograms exhibiting exothermic and endothermic peaks indicated the characteristic solid state reaction sequence of the 7017 alloy. Potentiodynamic polarization study of the 7017 alloy of various tempers in 3.5 wt.% NaCl solution at near neutral pH showed typical active metal dissolution behaviour, but at pH 12 an active–passive–transpassive transition behaviour has been observed. - Graphical abstract: TEM micrograph of the 7017 aluminium alloy of various tempers (a, b) under aged (T4), (c, d) peak aged (T6), (e, f) over aged (T7) and (g, h) highly over-aged. Display Omitted - Highlights: • 7017 Al-Zn-Mg alloy was subjected to different artificial ageing treatments. • Characterization of 7017 alloy tempers by hardness, tensile, DSC, TEM and electrochemical behaviour. • Structure-properties relationship of the 7017 Al-Zn-Mg alloy of various tempers.

  4. Microstructural changes to AlCu6Ni1 alloy after prolonged annealing at elevated temperature.

    PubMed

    Wierzbińska, M; Sieniawski, J

    2010-03-01

    This work presents results of microstructure examination of AlCu(6)Ni(1) aluminium alloy. The commercial AlCu(4)Ni(2)Mg(2) (M-309) alloy is widely used for elements of aircraft and automotive engines. Modification its chemical composition was aimed at improving the stability of mechanical properties of the alloy subjected to long-term exposure to high temperature. The alloy after standard T6 heat treatment (solution heat treated at 818 K/10 h/water quenched followed by ageing at 498 K/8 h/air cooled) was annealed for 150 h at elevated temperature of 573 K corresponding to the maximum value at which structural elements of jet piston engines made of aluminium alloys operate. It was found that applied heat treatment caused an increasing in the particles of hardening phase (theta'-Al(2)Cu) size. The significant growth of the length of theta'-Al(2)Cu precipitations was observed in particularly. Nevertheless, it did not strongly result in change of its shape - the 'crystallites' and 'rods' were still characteristic of hardening phase morphology. The phenomena of the growth of theta'-Al(2)Cu precipitates caused decreasing the mechanical properties of the alloy, what is the subject of further investigations by the authors.

  5. In vitro and in vivo studies of osteoblast cell response to a titanium-6 aluminium-4 vanadium surface modified by neodymium:yttrium-aluminium-garnet laser and silicon carbide paper.

    PubMed

    Khosroshahi, M E; Mahmoodi, M; Saeedinasab, H

    2009-11-01

    The effects of neodymium:yttrium-aluminium-garnet (Nd:YAG) laser and silicon carbide (SiC) paper on the surface micro-topography of titanium-6 aluminium-4 vanadium (Ti6Al4V) alloy were examined in relation to the response of bone cells. The study was performed in three distinct stages: (1) after surface treatment of samples by laser and SiC paper, the surface hardness, surface roughness, corrosion resistance and surface tension were evaluated; (2) the growth of mouse connective tissue fibroblast cells (L-929) on untreated and treated samples was assessed in vitro; (3) the response of goat osteoblast cells to untreated and treated implanted samples was assessed in vivo. The surface roughness varied between 7 +/- 0.02 for laser-treated samples (LTSs) at 140 J cm(-2) and 21.8 +/- 0.05 for mechanically treated samples (MTSs). The surface hardness was found to vary from 377 Vickers hardness number (VHN) for MTSs to 850 VHN for LTSs. A corrosion potential of -0.21V was achieved for the LTSs compared with -0.51V for the MTSs. The LTSs exhibited a more hydrophilic behaviour (i.e. wettability) than did the MTSs. No cytotoxicity effect, unlike for the MTSs, was observed for the LTSs. The results of in vivo tests indicated longitudinal growth of osteoblast cells along the grooves on the samples formed by the SiC paper, and multidirectional spreading of the cells on the LTSs.

  6. Die Soldering in Aluminium Die Casting

    SciTech Connect

    Han, Q.; Kenik, E.A.; Viswanathan, S.

    2000-03-15

    Two types of tests, dipping tests and dip-coating tests were carried out on small steel cylinders using pure aluminum and 380 alloy to investigate the mechanism of die soldering during aluminum die casting. Optical and scanning electron microscopy were used to study the morphology and composition of the phases formed during soldering. A soldering mechanism is postulated based on experimental observations. A soldering critical temperature is postulated at which iron begins to react with aluminum to form an aluminum-rich liquid phase and solid intermetallic compounds. When the temperature at the die surface is higher than this critical temperature, the aluminum-rich phase is liquid and joins the die with the casting during the subsequent solidification. The paper discusses the mechanism of soldering for the case of pure aluminum and 380 alloy casting in a steel mold, the factors that promote soldering, and the strength of the bond formed when soldering occurs. conditions, an aluminum-rich soldering layer may also form over the intermetallic layer. Although a significant amount of research has been conducted on the nature of these intermetallics, little is known about the conditions under which soldering occurs.

  7. [Plant physiological and molecular biological mechanism in response to aluminium toxicity].

    PubMed

    Liu, Qiang; Zheng, Shaojian; Lin, Xianyong

    2004-09-01

    Aluminium toxicity is the major factor limiting crop growth on acid soils, which greatly affects the crop productivity on about 40% cultivated soils of the world and 21% of China. In the past decades, a lot of researches on aluminium toxicity and resistant mechanisms have been doing, and great progress was achieved. This paper dealt with the genetic differences in aluminium tolerance among plants, screening and selecting methods and technologies for identifying aluminium resistance in plants, and physiological and molecular mechanism resistance to aluminium toxicity. Some aspects needed to be further studied were also briefly discussed.

  8. A Numerical Analysis of the Resistance and Stiffness of the Aluminium and Concrete Composite Beam

    NASA Astrophysics Data System (ADS)

    Polus, Łukasz; Szumigała, Maciej

    2015-03-01

    In this paper a numerical analysis of the resistance and stiffness of the aluminium and concrete composite beam is presented. Composite aluminium and concrete structures are quite new and they have not been thoroughly tested. Composite structures have a lot of advantages. The composite aluminium and concrete beam is more corrosion-resistant, fire-resistant and stiff than the aluminium beam. The contemporary idea of sustainable buildings relies on new solutions which are more environmentally friendly. Aluminium is lighter and more resistant to corrosion than steel, which is often used in composite structures.

  9. Influence of CrN-coating thickness on the corrosion resistance behaviour of aluminium-based bipolar plates

    NASA Astrophysics Data System (ADS)

    Barranco, José; Barreras, Félix; Lozano, Antonio; Maza, Mario

    The electrical and corrosion properties of CrN-coated aluminium alloy Magnal-45 (Al-5083) probes have been evaluated, in order to assess their viability to be used as bipolar plates in polymer electrolyte fuel cells. To this end, ceramic micro-layers of chromium nitride (CrN) with different thicknesses (3, 4, and 5 μm) have been deposited on the surface of the Al alloy (Al-5083) using the physical vapour deposition (PVD) technique. A decrease in 2 orders of magnitude of I corr values for the coated Al has been observed compared to the as-received Al-alloy when the probes have been exposed to simulated anodic conditions in a micro-reactor. On the other hand, when subjected to a cathodic-simulated environment, the Al-CrN probes with 3 μm and 4 μm coatings have shown a decrease in I corr of one order of magnitude, while a variation of two orders of magnitude has also been obtained for the 5 μm coating.

  10. Crashworthiness of Aluminium Tubes; Part 1: Hydroforming at Different Corner-Fill Radii and End Feeding Levels

    SciTech Connect

    D'Amours, Guillaume; Rahem, Ahmed; Williams, Bruce; Worswick, Michael; Mayer, Robert

    2007-05-17

    The automotive industry, with an increasing demand to reduce vehicle weight through the adoption of lightweight materials, requires a search of efficient methods that suit these materials. One attractive concept is to use hydroforming of aluminium tubes. By using FE simulations, the process can be optimized to reduce the risk for failure while maintaining energy absorption and component integrity under crash conditions. It is important to capture the level of residual ductility after forming to allow proper design for crashworthiness. This paper presents numerical and experimental studies that have been carried out for high pressure hydroforming operations to study the influence of the tube corner radius, end feeding, material thinning, and work hardening in 76.2 mm diameter, 3 mm wall thickness AA5754 aluminium alloy tube. End feeding was used to increase the formability of the tubes. The influence of the end feed displacement versus tube forming pressure schedule was studied to optimize the forming process operation to reduce thinning. Validation of the numerical simulations was performed by comparison of the predicted strain distributions and thinning, with measured quantities. The effect of element formulation (thin shell versus solid elements) was also considered in the models.

  11. On the hot cracking susceptibility of a semisolid aluminium 6061 weld: Application of a coupled solidification- thermomechanical model

    NASA Astrophysics Data System (ADS)

    Zareie Rajani, H. R.; Phillion, A. B.

    2015-06-01

    A coupled solidification-thermomechanical model is presented that investigates the hot tearing susceptibility of an aluminium 6061 semisolid weld. Two key phenomena are considered: excessive deformation of the semisolid weld, initiating a hot tear, and the ability of the semisolid weld to heal the hot tear by circulation of the molten metal. The model consists of two major modules: weld solidification and thermomechanical analysis. 1) By means of a multi-scale model of solidification, the microstructural evolution of the semisolid weld is simulated in 3D. The semisolid structure, which varies as a function of welding parameters, is composed of solidifying grains and a network of micro liquid channels. The weld solidification module is utilized to obtain the solidification shrinkage. The size of the micro liquid channels is used as an indicator to assess the healing ability of the semisolid weld. 2) Using the finite element method, the mechanical interaction between the weld pool and the base metal is simulated to capture the transient force field deforming the semisolid weld. Thermomechanical stresses and shrinkage stresses are both considered in the analysis; the solidification contractions are extracted from the weld solidification module and applied to the deformation simulation as boundary conditions. Such an analysis enables characterization of the potential for excessive deformation of the weld. The outputs of the model are used to study the effect of welding parameters including welding current and speed, and also welding constraint on the hot cracking susceptibility of an aluminium alloy 6061 semisolid weld.

  12. Effect of lysine acetylsalicylate on aluminium accumulation and (Na(+)/K(+))ATPase activity in rat brain cortex synaptosomes after aluminium ingestion.

    PubMed

    Silva, V S; Gonçalves, P P

    2015-01-05

    Aluminium is neurotoxic in humans and has been implicated in several neurological disorders. Chronic use of buffered aspirins, as aspegic, would likely constitute the major human aluminium uptake source. Low-dose aspirin is beneficial in secondary prevention of cardiovascular events, so it is widely used for long periods of time. We studied if oral administration of aspegic to rats modified the aluminium inhibitory effect on brain (Na(+)/K(+))ATPase due to alteration in synaptosomal membrane aluminium content. Adult male Wistar rats were submitted to sub-acute (1.00g/day during 10 days) and chronic (0.03g/day during 4 months) dietary AlCl3 exposure and/or to aspegic (0.11g/day). The exposure protocol increased the synaptosomal aluminium content especially after a long-term exposure to aluminium and aspegic. Although no alterations were observed in rat body weight gain and adenylate energy charge, the (Na(+)/K(+))ATPase activity was significantly reduced when aluminium was orally administered to rats. The oral administration of aspegic increased the synaptosomal aluminium content and concomitantly enhanced the (Na(+)/K(+))ATPase inhibition. In our exposure protocol the increase in synaptosomal aluminium content correlates with the reduction of the (Na(+)/K(+))ATPase activity.

  13. Electrochemical synthesis of nickel-aluminium oxide system from metals obtained by ore processing

    NASA Astrophysics Data System (ADS)

    Korobochkin, V. V.; Usoltseva, N. V.; Shorokhov, K. G.; Popova, E. V.

    2015-11-01

    Separate and combined electrochemical oxidation of aluminium and nickel has been conducted by alternating current of industrial frequency. Concentration increase of electrolyte solution (sodium chloride) in the range from 3 to 25 wt. % and current density from 0.5 to 1.5 A/cm2 was found to result in the increasing metal oxidation rate, excluding aluminium oxidation which oxidation rate is independent of the electrolyte solution concentration. At the current density of 1.5 A/cm2 the products of separate oxidation of nickel and aluminium are nickel oxyhydroxides, nickel hydroxides and aluminium oxyhydroxide (boehmite), respectively. In addition to these compounds, the nickel-aluminium oxide hydrate is included in the products of nickel and aluminium co-oxidation. Its content grows with the increasing electrolyte solution concentration. Varying the concentration and current density within the limits indicated, the nickel-aluminium oxide system with nickel oxide content from 3 to 10 wt. % is produced.

  14. Laser and pyrolysis removal of fluorinated ethylene propylene thin layers applied on EN AW-5251 aluminium substrates

    NASA Astrophysics Data System (ADS)

    Guerrero, G. R.; Sevilla, L.; Soriano, C.

    2015-10-01

    This work compares laser and pyrolysis removal procedures of the fluorinated ethylene propylene FEP-rich coatings applied on EN AW-5251 H34 aluminium magnesium alloy sheets. The study has been conducted in three successive FEP coating application-removal cycles. Roughness, yield and tensile strength, elongation percentage, hardness, grain size and constituent particles distribution of the processed samples have been analyzed. According to the results, it is concluded that similar mechanical properties has been obtained for both removal technologies, being the laser decoating removal rates lower than those achieved by the pyrolytic procedure. However, the laser decoating process is consolidated as an industrial alternative against the dangerous and harmful (to the environment) pyrolytic extraction systems.

  15. Effect of electromagnetic Stirring on the Element Distribution in Laser Beam Welding of Aluminium with Filler Wire

    NASA Astrophysics Data System (ADS)

    Gatzen, M.; Tang, Z.; Vollertsen, F.

    Additional external electromagnetic fields are used in laser beam welding of aluminium with silicon containing filler wire to manipulate the flow of the liquid metal due to induced volume forces and hence to modify the element distribution. Aiming for a better understanding of the fluid-dynamic processes inside the meld pool, a CFD model has been implemented to simulate the melt flow. In this paper, simulation results on the resulting element distribution of filler wire material under a coaxial magnetic field with different frequencies is compared to experimental results for the same parameters. It is shown that in both cases the concentration of alloying elements of the filler material has a spatial periodicity. From the CFD model it can be concluded that the change of the distribution of the filler material results from a modulation of the melt flow due to the periodic induced electromagnetic volume forces.

  16. Molecular Characterization of Aluminium (aluminum) Tolerance in Rye

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Aluminium (Al) toxicity, affecting around half of the world’s arable land, severely hinders the ability of crop plants to utilize moisture and nutrients by restricting root growth and function. Among the cultivated cereals, rye is the most Al-tolerant and represents an important potential source of ...

  17. Mechanochemical route to the synthesis of nanostructured Aluminium nitride

    NASA Astrophysics Data System (ADS)

    Rounaghi, S. A.; Eshghi, H.; Scudino, S.; Vyalikh, A.; Vanpoucke, D. E. P.; Gruner, W.; Oswald, S.; Kiani Rashid, A. R.; Samadi Khoshkhoo, M.; Scheler, U.; Eckert, J.

    2016-09-01

    Hexagonal Aluminium nitride (h-AlN) is an important wide-bandgap semiconductor material which is conventionally fabricated by high temperature carbothermal reduction of alumina under toxic ammonia atmosphere. Here we report a simple, low cost and potentially scalable mechanochemical procedure for the green synthesis of nanostructured h-AlN from a powder mixture of Aluminium and melamine precursors. A combination of experimental and theoretical techniques has been employed to provide comprehensive mechanistic insights on the reactivity of melamine, solid state metal-organic interactions and the structural transformation of Al to h-AlN under non-equilibrium ball milling conditions. The results reveal that melamine is adsorbed through the amine groups on the Aluminium surface due to the long-range van der Waals forces. The high energy provided by milling leads to the deammoniation of melamine at the initial stages followed by the polymerization and formation of a carbon nitride network, by the decomposition of the amine groups and, finally, by the subsequent diffusion of nitrogen into the Aluminium structure to form h-AlN.

  18. Porphyry copper enrichment linked to excess aluminium in plagioclase

    NASA Astrophysics Data System (ADS)

    Williamson, B. J.; Herrington, R. J.; Morris, A.

    2016-03-01

    Porphyry copper deposits provide around 75%, 50% and 20% of world copper, molybdenum and gold, respectively. The deposits are mainly centred on calc-alkaline porphyry magmatic systems in subduction zone settings. Although calc-alkaline magmas are relatively common, large porphyry copper deposits are extremely rare and increasingly difficult to discover. Here, we compile existing geochemical data for magmatic plagioclase, a dominant mineral in calc-alkaline rocks, from fertile (porphyry-associated) and barren magmatic systems worldwide, barren examples having no associated porphyry deposit. We show that plagioclase from fertile systems is distinct in containing `excess’ aluminium. This signature is clearly demonstrated in a case study carried out on plagioclase from the fertile La Paloma and Los Sulfatos copper porphyry systems in Chile. Further, the presence of concentric zones of high excess aluminium suggests its incorporation as a result of magmatic processes. As excess aluminium has been linked to high melt water contents, the concentric zones may record injections of hydrous fluid or fluid-rich melts into the sub-porphyry magma chamber. We propose that excess aluminium may exclude copper from plagioclase, so enriching the remaining melts. Furthermore, this chemical signature can be used as an exploration indicator for copper porphyry deposits.

  19. LASERS IN MEDICINE: Two-photon excitation of aluminium phthalocyanines

    NASA Astrophysics Data System (ADS)

    Meshalkin, Yu P.; Alfimov, E. E.; Vasil'ev, N. E.; Denisov, A. N.; Makukha, V. K.; Ogirenko, A. P.

    1999-12-01

    A demonstration is given of the feasibility of two-photon excitation of aluminium phthalocyanine and of the pharmaceutical preparation 'Fotosens', used in photodynamic therapy. The excitation source was an Nd:YAG laser emitting at the 1064 nm wavelength. The spectra of the two-photon-excited luminescence were obtained and the two-photon absorption cross sections were determined.

  20. Aluminium in food and daily dietary intake estimate in Greece.

    PubMed

    Bratakos, Sotirios M; Lazou, Andriana E; Bratakos, Michael S; Lazos, Evangelos S

    2012-01-01

    Aluminium content of foods, as well as dietary aluminium intake of the Greek adult population, was determined using graphite furnace atomic absorption spectroscopy after microwave sample digestion and food consumption data. Al content ranged from 0.02 to 741.2 mg kg⁻¹, with spices, high-spice foods, cereal products, vegetables and pulses found to be high in Al. Differences in aluminium content were found between different food classes from Greece and those from some other countries. Aluminium intake of Greeks is 3.7 mg/day based on DAFNE Food Availability Databank, which uses data from the Household Budget Surveys. On the other hand, according to the per capita food consumption data collected by both national and international organisations, Al intake is 6.4 mg day⁻¹. Greek adult population has an Al intake lower than the Provisional Tolerable Weekly Intake of 7 mg kg⁻¹ body weight established by EFSA. Cereals and vegetables are the main Al contributors, providing 72.4% of daily intake.

  1. On the anodic aluminium oxide refractive index of nanoporous templates

    NASA Astrophysics Data System (ADS)

    Hierro-Rodriguez, A.; Rocha-Rodrigues, P.; Valdés-Bango, F.; Alameda, J. M.; Jorge, P. A. S.; Santos, J. L.; Araujo, J. P.; Teixeira, J. M.; Guerreiro, A.

    2015-11-01

    In the present study, we have determined the intrinsic refractive index of anodic aluminium oxide, which is originated by the formation of nanoporous alumina templates. Different templates have been fabricated by the conventional two-step anodization procedure in oxalic acid. Their porosities were modified by chemical wet etching allowing the tuning of their effective refractive indexes (air-filled nanopores  +  anodic aluminium oxide). By standard spectroscopic light transmission measurements, the effective refractive index for each different template was extracted in the VIS-NIR region. The determination of the intrinsic anodic aluminium oxide refractive index was performed by using the Maxwell-Garnett homogenization theory. The results are coincident for all the fabricated samples. The obtained refractive index (~1.55) is quite lower (~22%) than the commonly used Al2O3 handbook value (~1.75), showing that the amorphous nature of the anodic oxide structure strongly conditions its optical properties. This difference is critical for the correct design and modeling of optical plasmonic metamaterials based on anodic aluminium oxide nanoporous templates.

  2. Mechanochemical route to the synthesis of nanostructured Aluminium nitride

    PubMed Central

    Rounaghi, S. A.; Eshghi, H.; Scudino, S.; Vyalikh, A.; Vanpoucke, D. E. P.; Gruner, W.; Oswald, S.; Kiani Rashid, A. R.; Samadi Khoshkhoo, M.; Scheler, U.; Eckert, J.

    2016-01-01

    Hexagonal Aluminium nitride (h-AlN) is an important wide-bandgap semiconductor material which is conventionally fabricated by high temperature carbothermal reduction of alumina under toxic ammonia atmosphere. Here we report a simple, low cost and potentially scalable mechanochemical procedure for the green synthesis of nanostructured h-AlN from a powder mixture of Aluminium and melamine precursors. A combination of experimental and theoretical techniques has been employed to provide comprehensive mechanistic insights on the reactivity of melamine, solid state metal-organic interactions and the structural transformation of Al to h-AlN under non-equilibrium ball milling conditions. The results reveal that melamine is adsorbed through the amine groups on the Aluminium surface due to the long-range van der Waals forces. The high energy provided by milling leads to the deammoniation of melamine at the initial stages followed by the polymerization and formation of a carbon nitride network, by the decomposition of the amine groups and, finally, by the subsequent diffusion of nitrogen into the Aluminium structure to form h-AlN. PMID:27650956

  3. Aluminium in allergen-specific subcutaneous immunotherapy--a German perspective.

    PubMed

    Kramer, Matthias F; Heath, Matthew D

    2014-07-16

    We are living in an "aluminium age" with increasing bioavailability of the metal for approximately 125 years, contributing significantly to the aluminium body burden of humans. Over the course of life, aluminium accumulates and is stored predominantly in the lungs, bones, liver, kidneys and brain. The toxicity of aluminium in humans is briefly summarised, highlighting links and possible causal relationships between a high aluminium body burden and a number of neurological disorders and disease states. Aluminium salts have been used as depot-adjuvants successfully in essential prophylactic vaccinations for almost 100 years, with a convincing positive benefit-risk assessment which remains unchanged. However, allergen-specific immunotherapy commonly consists of administering a long-course programme of subcutaneous injections using preparations of relevant allergens. Regulatory authorities currently set aluminium limits for vaccines per dose, rather than per treatment course. Unlike prophylactic vaccinations, numerous injections with higher proportions of aluminium-adjuvant per injection are applied in subcutaneous immunotherapy (SCIT) and will significantly contribute to a higher cumulative life dose of aluminium. While the human body may cope robustly with a daily aluminium overload from the environment, regulatory cumulative threshold values in immunotherapy need further addressing. Based on the current literature, predisposing an individual to an unusually high level of aluminium, such as through subcutaneous immunotherapy, has the potential to form focal accumulations in the body with the propensity to exert forms of toxicity. Particularly in relation to longer-term health effects, the safety of aluminium adjuvants in immunotherapy remains unchallenged by health authorities - evoking the need for more consideration, guidance, and transparency on what is known and not known about its safety in long-course therapy and what measures can be taken to prevent or

  4. Corrosion Behaviour of A380 Aluminiun Alloy by Semi-Solid Rheocasting

    NASA Astrophysics Data System (ADS)

    Forn, A.; Rupérez, E.; Baile, M. T.; Campillo, M.; Menargues, S.; Espinosa, I.

    2007-04-01

    A comparative study was performed on the corrosion behavior of a component of A380 aluminium alloy obtained by Semi-Solid Rheocasting (SSR). The effect of heat treatments T5 and T6 on corrosion resistance was compared with components without heat treatment by SSR processes. Corrosion studies were performed using an acetic acid salt spray test, impedance measurements and polarization curves using a 3,5%Na Cl test solution. The corrosion progress is described by micrographic analysis.

  5. Corrosion Behaviour of A380 Aluminiun Alloy by Semi-Solid Rheocasting

    SciTech Connect

    Forn, A.; Ruperez, E.; Baile, M. T.; Campillo, M.; Menargues, S.; Espinosa, I.

    2007-04-07

    A comparative study was performed on the corrosion behavior of a component of A380 aluminium alloy obtained by Semi-Solid Rheocasting (SSR). The effect of heat treatments T5 and T6 on corrosion resistance was compared with components without heat treatment by SSR processes. Corrosion studies were performed using an acetic acid salt spray test, impedance measurements and polarization curves using a 3,5%Na Cl test solution. The corrosion progress is described by micrographic analysis.

  6. The Young's Modulus of 1018 Steel and 6061-T6 Aluminium Measured from Quasi-Static to Elastic Precursor Strain-Rates

    NASA Astrophysics Data System (ADS)

    Rae, Philip J.; Trujillo, Carl P.; Lovato, Manuel L.

    2009-12-01

    The assumption that Young's modulus is strain-rate invariant is tested for 6061-T6 aluminium alloy and 1018 steel over 10 decades of strain-rate. For the same billets of material, 3 quasi-static strain-rates are investigated with foil strain gauges at room temperature. The ultrasonic sound speeds are measured and used to calculate the moduli at approximately 104 s-1. Finally, 1D plate impact is used to generate an elastic pre-cursor in the alloys at a strain-rate of approximately 106 s1 from which the longitudinal sound speed may be obtained. It is found that indeed the Young's modulus is strain-rate independent within the experimental accuracy.

  7. Centrifugal Casting Features/Metallurgical Characterization of Aluminum Alloys

    SciTech Connect

    Chirita, G.; Soares, D.; Cruz, D.; Silva, F. S.; Stefanescu, I.

    2008-02-15

    This paper deals with the study of centrifugal effects on aluminium castings under high G values. Most of the studies in this domain (FGMs obtained by centrifugal casting) deal with functionally graded composites reinforced with a solid phase such as silicon particles or others. However, in this study it will be shown that unreinforced aluminium alloys may be significantly influenced by the centrifugal effect and that functionally graded castings are also obtained. It has been observed that the centrifugal effect may increase in some alloys, depending on the relative position in the castings, the rupture strength by approx. 50%, and rupture strain by about 300%, as compared to the gravity casting technique. The Young's modulus may also increase by about 20%. It has also been reported that in vertical centrifugal castings there are mainly three aspects that affect the components thus obtained, namely: fluid dynamics; vibration (inherent to the system); and centrifugal force. These features have a different effect on the castings depending on the aluminium alloy. In this paper, an analysis of the most important effects of the centrifugal casting process on metallurgical features is conducted. A solidification characterization at several points along the mould will be made in order to have an accurate idea of both the fluid dynamics inside the mould during the casting and the solidification behavior in different parts of the component. These two analyses will be related to the metallurgical properties (phase distribution; SDAS; eutectic silicon content and shape, pores density and shape) along the component and mainly along the direction of the centrifugal pressure. A comparison between castings obtained by both centrifugal casting technique and gravity casting technique is made for reference (gravity casting)

  8. Protective effect of curcumin (Curcuma longa), against aluminium toxicity: Possible behavioral and biochemical alterations in rats.

    PubMed

    Kumar, Anil; Dogra, Samrita; Prakash, Atish

    2009-12-28

    Aluminium is a potent neurotoxin and has been associated with Alzheimer's disease (AD) causality for decades. Prolonged aluminium exposure induces oxidative stress and increases amyloid beta levels in vivo. Current treatment modalities for AD provide only symptomatic relief thus necessitating the development of new drugs with fewer side effects. The aim of the study was to demonstrate the protective effect of chronic curcumin administration against aluminium-induced cognitive dysfunction and oxidative damage in rats. Aluminium chloride (100 mg/kg, p.o.) was administered to rats daily for 6 weeks. Rats were concomitantly treated with curcumin (per se; 30 and 60 mg/kg, p.o.) daily for a period of 6 weeks. On the 21st and 42nd day of the study behavioral studies to evaluate memory (Morris water maze and elevated plus maze task paradigms) and locomotion (photoactometer) were done. The rats were sacrificed on 43rd day following the last behavioral test and various biochemical tests were performed to assess the extent of oxidative damage. Chronic aluminium chloride administration resulted in poor retention of memory in Morris water maze, elevated plus maze task paradigms and caused marked oxidative damage. It also caused a significant increase in the acetylcholinesterase activity and aluminium concentration in aluminium treated rats. Chronic administration of curcumin significantly improved memory retention in both tasks, attenuated oxidative damage, acetylcholinesterase activity and aluminium concentration in aluminium treated rats (P<0.05). Curcumin has neuroprotective effects against aluminium-induced cognitive dysfunction and oxidative damage.

  9. Bioleaching of zinc and aluminium from industrial waste sludges by means of Thiobacillus ferrooxidans.

    PubMed

    Solisio, C; Lodi, A; Veglio, F

    2002-01-01

    Biological solubilisation of heavy metals contained in two different kinds of industrial wastes was performed in batches employing a strain of Thiobacillus ferroxidans. The wastes tested were: a dust coming from the iron-manganese alloy production in an electric furnace (sludge 1) and a sludge coming from a process treatment plant of aluminium anodic oxidation (sludge 2). The experimental results pointed out the ability of the used strain to maintain the environment, that initially has a pH about 8, at strongly acid conditions (pH 2.5-3.5), producing sulphuric acid that is the chemical agent responsible for the metals solubilisation. At wastes initial concentration of 1%, the percentage of solubilised metals was 76 and 78% for the wastes 1 and 2, respectively, but the lag phase was considerably longer for sludge 2 than for sludge 1, indicating a different affinity of microorganisms for the solid phase. Increasing the initial slurry concentration, the percentage of removed metal reached 72-73% for the sludge 1, while in case of sludge 2, the total amount of solubilized metal progressively decreased. Two kinetic models are proposed to describe the trends of metals solubilization curves.

  10. Aluminium-phosphorus interactions in plants growing on acid soils: does phosphorus always alleviate aluminium toxicity?

    PubMed

    Chen, Rong Fu; Zhang, Fu Lin; Zhang, Qi Ming; Sun, Qing Bin; Dong, Xiao Ying; Shen, Ren Fang

    2012-03-30

    Aluminium (Al) toxicity and phosphorus (P) deficiency are considered to be the main constraints for crop production in acid soils, which are widely distributed in tropical and subtropical regions. Conventionally, P addition is regarded as capable of alleviating Al toxicity in plants. However, this field is still rife with unsubstantiated theories, especially for different plant species growing on acid soils. In this review, the responses of plants to different methods of Al-P treatments are briefly summarized, and possible reasons are proposed by considering recent results from our laboratory. It is shown that: (1) long-term Al-P alternate treatment is advantageous for studying Al-P interactions in plants; (2) under the long-term Al-P alternate treatment, the roles of P in Al phytotoxicity might be associated with the Al resistance capability and P use efficiency of the plant, and a P/Al molar ratio exceeding 5 in roots may be the threshold of P alleviating Al toxicity based on the calculation of the tested plants; (3) in acid soils, P application may be effective only after Al stress is overcome for Al-sensitive species. Thus it is concluded that P application does not always alleviate Al toxicity under long-term Al-P alternate treatment.

  11. Aluminium content of foods originating from aluminium-containing food additives.

    PubMed

    Ogimoto, Mami; Suzuki, Kumi; Haneishi, Nahoko; Kikuchi, Yuu; Takanashi, Mayu; Tomioka, Naoko; Uematsu, Yoko; Monma, Kimio

    2016-09-01

    Aluminium (Al) levels of 90 food samples were investigated. Nineteen samples contained Al levels exceeding the tolerable weekly intake (TWI) for young children [body weight (bw): 16 kg] when consuming two servings/week. These samples were purchased multiple times at specific intervals and were evaluated for Al levels. Al was detected in 27 of the 90 samples at levels ranging from 0.01 (limit of quantitation) to 1.06 mg/g. Of these, the Al intake levels in two samples (cookie and scone mix, 1.3 and 2 mg/kg bw/week, respectively) exceeded the TWI as established by European Food Safety Authority, although the level in the scone mix was equivalent to the provisional TWI (PTWI) as established by Joint Food and Agriculture Organization of the United Nations/World Health Organization Expert Committee on Food Additives. The Al levels markedly decreased in 14 of the 19 samples with initially high Al levels. These results indicated reductions in the Al levels to below the PTWI limits in all but two previously identified food samples.

  12. Mössbauer and XRD study of Al-Sn linished steel bimetal alloy

    NASA Astrophysics Data System (ADS)

    Kuzmann, E.; Silva, L. da; Stichleutner, S.; El-Sharif, M.; Homonnay, Z.; Klencsár, Z.; Sziráki, L.; Chisholm, C. U.; Lak, B.

    2016-12-01

    Aluminium alloy free CS1 type steel (0.06 wt% C, 0.45 wt% Mn) and samples of cold roll bonded steel bimetal alloys (MAS15 and MAS16) were fabricated and investigated by X-ray diffraction (XRD), 57Fe conversion electron Mössbauer spectroscopy (CEMS) at room temperature. XRD has revealed only the existence of the alpha iron solid solution (steel) phase in the steel only sample, while identified steel and metallic Al and Sn constituent phases in the bimetallic alloys. 57Fe Mössbauer spectroscopy revealed the presence of 4 % secondary iron-bearing phase attributed mainly to iron oxide/ oxyhydroxides (ferrihydrite) besides the steel matrix on the surface of the steel sample. A significant difference between the occurrences of the secondary phase of differently prepared bimetal alloys found in their 57Fe CEM spectra allowed to identify the main phase of debris as different iron oxide/ oxyhydroxides.

  13. Alloy softening in binary molybdenum alloys

    NASA Technical Reports Server (NTRS)

    Stephens, J. R.; Witzke, W. R.

    1972-01-01

    An investigation was conducted to determine the effects of alloy additions of Hf, Ta, W, Re, Os, Ir, and Pt on the hardness of Mo. Special emphasis was placed on alloy softening in these binary Mo alloys. Results showed that alloy softening was produced by those elements having an excess of s+d electrons compared to Mo, while those elements having an equal number or fewer s+d electrons than Mo failed to produce alloy softening. Alloy softening and hardening can be correlated with the difference in number of s+d electrons of the solute element and Mo.

  14. Aluminium in food and daily dietary intake assessment from 15 food groups in Zhejiang Province, China.

    PubMed

    Zhang, Hexiang; Tang, Jun; Huang, Lichun; Shen, Xianghong; Zhang, Ronghua; Chen, Jiang

    2016-06-01

    Aluminium was measured in 2580 samples of 15 food groups and dietary exposure was estimated. Samples were purchased and analysed during 2010 to 2014. High aluminium levels were found in jellyfish (mean 4862 mg/kg), laver (mean 455.2 mg/kg) and fried twisted cruller (mean 392.4 mg/kg). Dietary exposure to aluminium was estimated for Zhejiang residents. The average dietary exposure to aluminium via 15 food groups in Zhejiang Province was 1.15 mg/kg bw/week, which is below the provisional tolerable weekly intake of 2 mg/kg bw /week. Jellyfish is the main Al contributor, providing 37.6% of the daily intake via these 15 food groups. This study provided new information on aluminium levels and assessment of aluminium (Al) dietary exposure in Zhejiang Province of China.

  15. RESPONSE OF PHENOLIC METABOLISM INDUCED BY ALUMINIUM TOXICITY IN FAGOPYRUM ESCULENTUM MOENCH. PLANTS.

    PubMed

    Smirnov, O E; Kosyan, A M; Kosyk, O I; Taran, N Yu

    2015-01-01

    Buckwheat genus (Fagopyrum Mill.) is one of the aluminium tolerant taxonomic units of plants. The aim of the study was an evaluation of the aluminium (50 μM effect on phenolic accumulation in various parts of buckwheat plants (Fagopyrum esculentum Moench). Detection of increasing of total phenolic content, changes in flavonoid and anthocyanin content and phenylalanine ammonia-lyase activity (PAL) were revealed over a period of 10 days of exposure to aluminium. The most significant effects of aluminium treatment on phenolic compounds accumulation were total phenolic content increasing (by 27.2%) and PAL activity rising by 2.5 times observed in leaves tissues. Received data could be helpful to understand the aluminium tolerance principles and relationships of phenolic compounds to aluminium phytotoxicity.

  16. Histopathological changes in cases of aluminium phosphide poisoning.

    PubMed

    Sinha, U S; Kapoor, A K; Singh, A K; Gupta, A; Mehrotra, Ravi

    2005-04-01

    Of a total of 205 poisoning deaths in our hospital in 2003, 83 cases were due to Aluminium phosphide poisoning and were further analyzed. Most vulnerable age group was 21-40 years and M:F ratio was 2:1. On naked eye examination, almost all the vital organs were found to be congested. On microscopic study, the liver showed central venous congestion, degeneration, haemorrhage, sinusoidal dilation, bile stasis, centrilobular necrosis, Kupffer cell hyperplasia, infiltration by mononuclear cells and fatty change. Microscopy of the lungs revealed alveolar thickening, oedema, dilated capillaries, collapsed alveoli and haemorrhage. In the kidney, changes were degeneration, infiltration, tubular dilation and cloudy swelling. Changes in the brain included congestion and coagulative necrosis and in the stomach, congestion and haemorrhage. Easy availability of this cheap and highly toxic substance was responsible for the sudden spurt of poisoning with aluminium phosphide.

  17. Surface roughness effects on aluminium-based ultraviolet plasmonic nanolasers

    PubMed Central

    Chung, Yi-Cheng; Cheng, Pi-Ju; Chou, Yu-Hsun; Chou, Bo-Tsun; Hong, Kuo-Bin; Shih, Jheng-Hong; Lin, Sheng-Di; Lu, Tien-Chang; Lin, Tzy-Rong

    2017-01-01

    We systematically investigate the effects of surface roughness on the characteristics of ultraviolet zinc oxide plasmonic nanolasers fabricated on aluminium films with two different degrees of surface roughness. We demonstrate that the effective dielectric functions of aluminium interfaces with distinct roughness can be analysed from reflectivity measurements. By considering the scattering losses, including Rayleigh scattering, electron scattering, and grain boundary scattering, we adopt the modified Drude-Lorentz model to describe the scattering effect caused by surface roughness and obtain the effective dielectric functions of different Al samples. The sample with higher surface roughness induces more electron scattering and light scattering for SPP modes, leading to a higher threshold gain for the plasmonic nanolaser. By considering the pumping efficiency, our theoretical analysis shows that diminishing the detrimental optical losses caused by the roughness of the metallic interface could effectively lower (~33.1%) the pumping threshold of the plasmonic nanolasers, which is consistent with the experimental results. PMID:28045127

  18. Prediction of the ballistic limit of an aluminium sandwich panel

    NASA Astrophysics Data System (ADS)

    Campbell, J.; De Vuyst, T.; Vignjevic, R.; Hughes, K.

    2016-08-01

    This paper presents research on modelling the impact of a 150g projectile on a 35mm thick aluminium sandwich panel. The objective of the work is a predictive modelling capability for the ballistic limit of the panel. A predictive modelling capability supports the design of capture and deorbit missions for large items of space debris such as satellites and rocket upper stages. A detailed explicit finite element model was built using the LSDYNA software and results were compared with experimental data for the projectile exit velocity to establish key parameters. The primary parameters influencing the model behaviour were the strength and failure of the aluminium face sheets and the friction between projectile and panel. The model results showed good agreement with experimental results for ogive nose projectiles, but overestimated the exit velocity for flat nose projectiles.

  19. Surface roughness effects on aluminium-based ultraviolet plasmonic nanolasers

    NASA Astrophysics Data System (ADS)

    Chung, Yi-Cheng; Cheng, Pi-Ju; Chou, Yu-Hsun; Chou, Bo-Tsun; Hong, Kuo-Bin; Shih, Jheng-Hong; Lin, Sheng-Di; Lu, Tien-Chang; Lin, Tzy-Rong

    2017-01-01

    We systematically investigate the effects of surface roughness on the characteristics of ultraviolet zinc oxide plasmonic nanolasers fabricated on aluminium films with two different degrees of surface roughness. We demonstrate that the effective dielectric functions of aluminium interfaces with distinct roughness can be analysed from reflectivity measurements. By considering the scattering losses, including Rayleigh scattering, electron scattering, and grain boundary scattering, we adopt the modified Drude-Lorentz model to describe the scattering effect caused by surface roughness and obtain the effective dielectric functions of different Al samples. The sample with higher surface roughness induces more electron scattering and light scattering for SPP modes, leading to a higher threshold gain for the plasmonic nanolaser. By considering the pumping efficiency, our theoretical analysis shows that diminishing the detrimental optical losses caused by the roughness of the metallic interface could effectively lower (~33.1%) the pumping threshold of the plasmonic nanolasers, which is consistent with the experimental results.

  20. Persistent Skin Reactions and Aluminium Hypersensitivity Induced by Childhood Vaccines.

    PubMed

    Salik, Elaha; Løvik, Ida; Andersen, Klaus E; Bygum, Anette

    2016-11-02

    There is increasing awareness of reactions to vaccination that include persistent skin reactions. We present here a retrospective investigation of long-lasting skin reactions and aluminium hypersensitivity in children, based on medical records and questionnaires sent to the parents. In the 10-year period 2003 to 2013 we identified 47 children with persistent skin reactions caused by childhood vaccinations. Most patients had a typical presentation of persisting pruritic subcutaneous nodules. Five children had a complex diagnostic process involving paediatricians, orthopaedics and plastic surgeons. Two patients had skin biopsies performed from their skin lesions, and 2 patients had the nodules surgically removed. Forty-two children had a patch-test performed with 2% aluminium chloride hexahydrate in petrolatum and 39 of them (92%) had a positive reaction. The persistent skin reactions were treated with potent topical corticosteroids and disappeared slowly. Although we advised families to continue vaccination of their children, one-third of parents omitted or postponed further vaccinations.

  1. Effects of breadfruit seed hull ash on the microstructures and properties of Al-Si-Fe alloy/breadfruit seed hull ash particulate composites

    NASA Astrophysics Data System (ADS)

    Atuanya, C. U.; Ibhadode, A. O. A.; Dagwa, I. M.

    2012-01-01

    The microstructures and properties of Al-Si-Fe alloy matrix composites reinforced with different weight fractions of breadfruit seed hull (husk) ash particles of size 500 nm were investigated. Six (6) different weight fractions of breadfruit seed hull ash particles were added to aluminium alloy matrix using a double stir-casting method. Microstructural analysis shows that with the increase of the reinforcement weight fraction, the matrix grain size decreases. The mechanical properties of the composites are improved over the matrix materials, except for the slightly decrease of the impact energy. Fracture surface examination indicates that there is a good interfacial bonding between the aluminium alloy matrix and the breadfruit seed hull ash particles and that fracture initiation does not occur at the particle-matrix interface. Hence, incorporation of breadfruit seed hull ash particles in aluminium matrix can lead to the production of low cost aluminium composites with improved hardness and strength. These composites can find applications in automotive components where light weight materials are required with good stiffness and strength.

  2. Comparative genotoxicity of aluminium and cadmium in embryonic zebrafish cells.

    PubMed

    Pereira, Sandrine; Cavalie, Isabelle; Camilleri, Virginie; Gilbin, Rodolphe; Adam-Guillermin, Christelle

    2013-01-20

    Aluminium is a toxic metal whose genotoxicity has been scarcely studied in aquatic species and more generally in mammals. Recently, human and ecological disaster caused by the discharge of red mud in Hungary has revived questions about the toxicity of this metal particularly for the environment. On the contrary, cadmium is a highly toxic metal whose genotoxicity has been well characterized in various mammalian cells. However on non-human cells, little is known about its impact on DNA damage and repair. In this study, the genotoxic potential of both metals on embryonic zebrafish cells ZF4 was analyzed and particularly the impairment of the major DNA double strand breaks (DSB)-repair pathway, i.e. non-homologous end-joining (NHEJ). To this aim, DNA single strand breaks (SSB) and DSB were evaluated using the comet assay and the immunodetection of γ-H2AX proteins, respectively, in AlCl(3) or CdCl(2) exposed ZF4 cells. These exposures result in the production of DSBs a few hours after incubation. The DNA-PK kinase activity, essential for NHEJ, is more affected by the presence of aluminium than cadmium. Altogether our data provide evidence of the high toxicity induced by aluminium in zebrafish and indicates the pertinence of genotoxicity evaluation in organisms living in contaminated water.

  3. Recovering obliterated engraved marks on aluminium surfaces by etching technique.

    PubMed

    Baharum, Mohd Izhar Mohd; Kuppuswamy, R; Rahman, Azari Abd

    2008-05-20

    A study has been made of the characteristics of restoration of obliterated engraved marks on aluminium surfaces by etching technique. By etching different reagents on 0.61mm thick sheets of aluminium (99wt%) on which some engraved marks had been erased to different depths it was found that the reagent 60% hydrochloric acid and 40% sodium hydroxide on alternate swabbing on the surfaces was found to be the most sensitive one for these metal surfaces. This reagent was able to restore marks in the above plates erased down to 0.04mm below the bottom of the engraving. The marks also presented excellent contrast with the background. This reagent was further experimented with similar aluminium surfaces, but of relatively greater thickness of 1.5mm. It was noticed that the recovery depth increased slightly to 0.06mm; this suggested the dependence of recovery depth on the thickness of the sheet metal. Further, the depth of restoration decreased in cases where the original number was erased and over which a new number was engraved; the latter results are similar to those of steel surfaces reported earlier [M.A.M. Zaili, R. Kuppuswamy, H. Harun, Restoration of engraved marks on steel surfaces by etching technique, Forensic Sci. Int. 171 (2007) 27-32].

  4. Modelling of detonation cellular structure in aluminium suspensions

    NASA Astrophysics Data System (ADS)

    Briand, A.; Veyssiere, B.; Khasainov, B. A.

    2010-12-01

    Heterogeneous detonations involving aluminium suspensions have been studied for many years for industrial safety policies, and for military and propulsion applications. Owing to their weak detonability and to the lack of available experimental results on the detonation cellular structure, numerical simulations provide a convenient way to improve the knowledge of such detonations. One major difficulty arising in numerical study of heterogeneous detonations involving suspensions of aluminium particles in oxidizing atmospheres is the modelling of aluminium combustion. Our previous two-step model provided results on the effect on the detonation cellular structure of particle diameter and characteristic chemical lengths. In this study, a hybrid model is incorporated in the numerical code EFAE, combining both kinetic and diffusion regimes in parallel. This more realistic model provides good agreement with the previous two-step model and confirms the correlations found between the detonation cell width, and particle diameter and characteristic lengths. Moreover, the linear dependence found between the detonation cell width and the induction length remains valid with the hybrid model.

  5. Spectroscopic diagnostics of plasma during laser processing of aluminium

    NASA Astrophysics Data System (ADS)

    Lober, R.; Mazumder, J.

    2007-10-01

    The role of the plasma in laser-metal interaction is of considerable interest due to its influence in the energy transfer mechanism in industrial laser materials processing. A 10 kW CO2 laser was used to study its interaction with aluminium under an argon environment. The objective was to determine the absorption and refraction of the laser beam through the plasma during the processing of aluminium. Laser processing of aluminium is becoming an important topic for many industries, including the automobile industry. The spectroscopic relative line to continuum method was used to determine the electron temperature distribution within the plasma by investigating the 4158 Å Ar I line emission and the continuum adjacent to it. The plasmas are induced in 1.0 atm pure Ar environment over a translating Al target, using f/7 and 10 kW CO2 laser. Spectroscopic data indicated that the plasma composition and behaviour were Ar-dominated. Experimental results indicated the plasma core temperature to be 14 000-15 300 K over the incident range of laser powers investigated from 5 to 7 kW. It was found that 7.5-29% of the incident laser power was absorbed by the plasma. Cross-section analysis of the melt pools from the Al samples revealed the absence of any key-hole formation and confirmed that the energy transfer mechanism in the targets was conduction dominated for the reported range of experimental data.

  6. Toxicity of indium arsenide, gallium arsenide, and aluminium gallium arsenide.

    PubMed

    Tanaka, Akiyo

    2004-08-01

    Gallium arsenide (GaAs), indium arsenide (InAs), and aluminium gallium arsenide (AlGaAs) are semiconductor applications. Although the increased use of these materials has raised concerns about occupational exposure to them, there is little information regarding the adverse health effects to workers arising from exposure to these particles. However, available data indicate these semiconductor materials can be toxic in animals. Although acute and chronic toxicity of the lung, reproductive organs, and kidney are associated with exposure to these semiconductor materials, in particular, chronic toxicity should pay much attention owing to low solubility of these materials. Between InAs, GaAs, and AlGaAs, InAs was the most toxic material to the lung followed by GaAs and AlGaAs when given intratracheally. This was probably due to difference in the toxicity of the counter-element of arsenic in semiconductor materials, such as indium, gallium, or aluminium, and not arsenic itself. It appeared that indium, gallium, or aluminium was toxic when released from the particles, though the physical character of the particles also contributes to toxic effect. Although there is no evidence of the carcinogenicity of InAs or AlGaAs, GaAs and InP, which are semiconductor materials, showed the clear evidence of carcinogenic potential. It is necessary to pay much greater attention to the human exposure of semiconductor materials.

  7. Pulse electrodeposition of adherent nickel coatings onto anodized aluminium surfaces

    NASA Astrophysics Data System (ADS)

    Frantz, Cédric; Vichery, Charlotte; Zechner, Johannes; Frey, Damian; Bürki, Gerhard; Cebeci, Halil; Michler, Johann; Philippe, Laetitia

    2015-03-01

    Aluminium is one of the mostly used elements in the industry because of its abundance and low weight. However, the deposition of a metallic coating requires performing the so-called zincate pre-treatment in order to allow the formation of inter-metallic bonds and thereby achieving sufficient adherence. In this work, porous anodic aluminium oxide (AAO) is used as an anchoring intermediate layer for nickel coatings. AAO is grown anodically in sulfuric acid and nickel coatings are deposited by potentiostatic reverse pulse electrodeposition onto as-anodized aluminium surfaces. The electrodeposition of nickel is initiated onto the electrochemically thinned barrier layer of AAO and pursued until the complete covering of the oxide. The electrochemical behavior of Watts and sulfamate baths is investigated by cyclic voltammetry for different barrier layer thickness, allowing to validate the thinning conditions and to determine the appropriate deposition potential of nickel. GD-OES measurements show that low duty cycles are necessary to achieve high filling ratio of the AAO. SEM micrographs show that a smooth uniform coating is obtained when nickel is deposited in presence of additives.

  8. Control of Microthrix parvicella by aluminium salts addition.

    PubMed

    Durban, N; Juzan, L; Krier, J; Gillot, S

    2016-01-01

    Aluminium and iron chloride were added to a biological nutrient removal pilot plant (1,500 population equivalent) treating urban wastewater to investigate the control of Microthrix parvicella bulking and foaming by metallic salts. Monitoring plant performance over two 6-month periods showed a slight impact on the removal efficiencies. Addition of metallic salts (Me; aluminium or aluminium + iron) at a concentration of 41 mmol Me(kg MLSS·d) (MLSS: mixed liquor suspended solids) over 70 days allowed a stabilization of the diluted sludge volume index (DSVI), whereas higher dosages (94 mmol Me(kg MLSS·d) over 35 days or 137 mmol Me(kg MLSS·d) over 14 days induced a significant improvement of the settling conditions. Microscopic observations showed a compaction of biological aggregates with an embedding of filamentous bacteria into the flocs that is not specific to M. parvicella as bacteria from phylum Chloroflexi are embedded too. The quantitative polymerase chain reaction targeting M. parvicella further indicated a possible growth limitation in addition to the flocculation impact at the high dosages of metallic salts investigated. DSVI appeared to be correlated with the relative abundance of M. parvicella.

  9. Stock dynamics and emission pathways of the global aluminium cycle

    NASA Astrophysics Data System (ADS)

    Liu, Gang; Bangs, Colton E.; Müller, Daniel B.

    2013-04-01

    Climate change mitigation in the materials sector faces a twin challenge: satisfying rapidly rising global demand for materials while significantly curbing greenhouse-gas emissions. Process efficiency improvement and recycling can contribute to reducing emissions per material output; however, long-term material demand and scrap availability for recycling depend fundamentally on the dynamics of societies' stocks of products in use, an issue that has been largely neglected in climate science. Here, we show that aluminium in-use stock patterns set essential boundary conditions for future emission pathways, which has significant implications for mitigation priority setting. If developing countries follow industrialized countries in their aluminium stock patterns, a 50% emission reduction by 2050 below 2000 levels cannot be reached even under very optimistic recycling and technology assumptions. The target can be reached only if future global per-capita aluminium stocks saturate at a level much lower than that in present major industrialized countries. As long as global in-use stocks are growing rapidly, radical new technologies in primary production (for example, inert anode and carbon capture and storage) have the greatest impact in emission reduction; however, their window of opportunity is closing once the stocks begin to saturate and the largest reduction potential shifts to post-consumer scrap recycling.

  10. Comparison of the x-ray attenuation properties of breast calcifications, aluminium, hydroxyapatite and calcium oxalate

    NASA Astrophysics Data System (ADS)

    Warren, L. M.; Mackenzie, A.; Dance, D. R.; Young, K. C.

    2013-04-01

    Aluminium is often used as a substitute material for calcifications in phantom measurements in mammography. Additionally, calcium oxalate, hydroxyapatite and aluminium are used in simulation studies. This assumes that these materials have similar attenuation properties to calcification, and this assumption is examined in this work. Sliced mastectomy samples containing calcification were imaged at ×5 magnification using a digital specimen cabinet. Images of the individual calcifications were extracted, and the diameter and contrast of each calculated. The thicknesses of aluminium required to achieve the same contrast as each calcification when imaged under the same conditions were calculated using measurements of the contrast of aluminium foils. As hydroxyapatite and calcium oxalate are also used to simulate calcifications, the equivalent aluminium thicknesses of these materials were also calculated using tabulated attenuation coefficients. On average the equivalent aluminium thickness was 0.85 times the calcification diameter. For calcium oxalate and hydroxyapatite, the equivalent aluminium thicknesses were 1.01 and 2.19 times the thickness of these materials respectively. Aluminium and calcium oxalate are suitable substitute materials for calcifications. Hydroxyapatite is much more attenuating than the calcifications and aluminium. Using solid hydroxyapatite as a substitute for calcification of the same size would lead to excessive contrast in the mammographic image.

  11. Aluminium removal with the double chamber technique: paired filtration-dialysis (PFD).

    PubMed

    Fernández-Martín, J L; Douthat, W; Barreto, S; Canteros, A; Acuña, G; Cannata Andía, J B

    1998-01-01

    Several dialysis techniques have been used to improve aluminium removal. So far there are no data available using paired filtration-dialysis (PFD). In this study, we evaluated the aluminium removed by PFD in two phases. Bovine plasma with known concentrations of aluminium and desferrioxamine was used in both experiments. In phase I, the aluminium removal was investigated using the PFD system (single pass) in its usual configuration, modifying the order of the convective and diffusive processes, dialysis with high permeability membranes and dialysis with low permeability membranes. During the second phase, the experiment lasted longer using recirculation, and the PFD was compared with conventional dialysis using high permeability membranes. Changes in the PFD configuration did not alter the aluminium removal; the efficiency of PFD for aluminium removal was very close to that of dialysis with high permeability membranes and much greater than with low permeability membranes. The aluminium is removed mainly in the first part of the dialysis. Aluminium mobilization using the double chamber technique (PFD) was efficient and might be of value for those patients with aluminium overload who needs high depurative techniques and are unable to tolerate high-flux techniques.

  12. Neuroprotective effect of Allium cepa L. in aluminium chloride induced neurotoxicity.

    PubMed

    Singh, Tanveer; Goel, Rajesh Kumar

    2015-07-01

    The present study was envisaged to investigate the neuroprotective potential of Allium cepa (A. cepa) in aluminium chloride induced neurotoxicity. Aluminium chloride (50 mg/kg/day) was administered orally in mice supplemented with different doses of A. cepa hydroethanolic extract for a period of 60 days. Various behavioural, biochemical and histopathological parameters were estimated in aluminium exposed animals. Chronic aluminium administration resulted in significant motor incoordination and memory deficits, which were also endorsed biochemically as there was increased oxidative stress as well as elevated acetylcholinesterase (AChE) and aluminium levels in the brain. Supplementation with A. cepa in aluminium exposed animals significantly improved muscle coordination and memory deficits as well as reduced oxidative stress, AChE and decreased abnormal aluminium deposition in the brain. Histopathologically, there was marked deterioration visualized as decreased vacuolated cytoplasm as well as decreased pyramidal cells in the hippocampal area of mice brain which were found to be reversed with A. cepa supplementation. Administration of BADGE (PPARγ antagonist) in aluminium exposed animals reversed the neuroprotective potential of A. cepa as assessed with various behavioural, biochemical, neurochemical and histopathological estimations. In conclusion, finding of this study suggested significant neuroprotective potential of A. cepa in aluminium induced neurotoxicity. Further, the role of PPARγ receptor agonism has also been suggested as a putative neuroprotective mechanism of A. cepa, which needs further studies for confirmation.

  13. Dietary exposure to aluminium and health risk assessment in the residents of Shenzhen, China.

    PubMed

    Yang, Mei; Jiang, Lixin; Huang, Huiping; Zeng, Shengbo; Qiu, Fen; Yu, Miao; Li, Xiaorong; Wei, Sheng

    2014-01-01

    Although there are great changes of dietary in the past few decades in China, few are known about the aluminium exposure in Chinese diet. The aim of this study is to systematically evaluate the dietary aluminium intake level in residents of Shenzhen, China. A total of 853 persons from 244 household were investigated their diet by three days food records. Finally, 149 kinds of foods in 17 food groups were selected to be the most consumed foods. From them, 1399 food samples were collected from market to test aluminium concentration. High aluminium levels were found in jellyfish (median, 527.5 mg/kg), fried twisted cruller (median, 466.0 mg/kg), shell (median, 107.1 mg/kg). The Shenzhen residents' average dietary aluminium exposure was estimated at 1.263 mg/kg bw/week which is lower than the PTWI (provisional tolerable weekly intake). But 0-2 and 3-13 age groups have the highest aluminium intake exceeding the PTWI (3.356 mg/kg bw/week and 3.248 mg/kg bw/week) than other age groups. And the main dietary aluminium exposure sources are fried twisted cruller, leaf vegetables and bean products. Our study suggested that even three decades rapid economy development, children in Shenzhen still have high dietary aluminium exposure risk. How to control high dietary aluminium exposure still is a great public health challenge in Shenzhen, China.

  14. Comparison of the x-ray attenuation properties of breast calcifications, aluminium, hydroxyapatite and calcium oxalate.

    PubMed

    Warren, L M; Mackenzie, A; Dance, D R; Young, K C

    2013-04-07

    Aluminium is often used as a substitute material for calcifications in phantom measurements in mammography. Additionally, calcium oxalate, hydroxyapatite and aluminium are used in simulation studies. This assumes that these materials have similar attenuation properties to calcification, and this assumption is examined in this work. Sliced mastectomy samples containing calcification were imaged at ×5 magnification using a digital specimen cabinet. Images of the individual calcifications were extracted, and the diameter and contrast of each calculated. The thicknesses of aluminium required to achieve the same contrast as each calcification when imaged under the same conditions were calculated using measurements of the contrast of aluminium foils. As hydroxyapatite and calcium oxalate are also used to simulate calcifications, the equivalent aluminium thicknesses of these materials were also calculated using tabulated attenuation coefficients. On average the equivalent aluminium thickness was 0.85 times the calcification diameter. For calcium oxalate and hydroxyapatite, the equivalent aluminium thicknesses were 1.01 and 2.19 times the thickness of these materials respectively. Aluminium and calcium oxalate are suitable substitute materials for calcifications. Hydroxyapatite is much more attenuating than the calcifications and aluminium. Using solid hydroxyapatite as a substitute for calcification of the same size would lead to excessive contrast in the mammographic image.

  15. Galvanic interactions of aluminium 3004 and ∝ brass in tropical marine atmosphere

    NASA Astrophysics Data System (ADS)

    Palraj, S.; Subramanian, G.; Palanichamy, S.

    2014-12-01

    The galvanic corrosion behaviour of aluminium 3004 - ∝ brass with different area ratios was studied in the tropical marine atmosphere at Tuticorin harbour over a period of 426 days. The area ratios, viz. A Aluminium: A ∝ brass, studied were 0.125, 0.25, 0.5, 1, 2, 4 and 8. The galvanic corrosion behaviour of the metals was studied in terms of the relative increase in the corrosion rate of aluminium due to galvanic coupling with ∝ brass, the relative decrease in the corrosion rate of ∝ brass due to galvanic coupling with aluminium, and the susceptibility of aluminium to pitting owing to galvanic coupling with ∝ brass. The galvanic potential and galvanic current of the system were monitored. Pits of different dimensions ranging from mild etchings to perforations were experienced on the borders and the surfaces of the interface of aluminium in contact with ∝ brass. The corrosion products resulting from galvanic corrosion were analysed using XRD and the pitting on aluminium as a result of galvanic corrosion was highlighted in terms of pit depth, size and density of pit, using a high resolution microscope. The most favourable area ratio of aluminium — ∝ brass in marine atmosphere in terms of gravimetric corrosion rate is 8:1 and the most unfavourable area ratio of aluminium — ∝ brass is 1:4.

  16. Aluminium localization in root tips of the aluminium-accumulating plant species buckwheat (Fagopyrum esculentum Moench).

    PubMed

    Klug, Benjamin; Specht, André; Horst, Walter J

    2011-11-01

    Aluminium (Al) uptake and transport in the root tip of buckwheat is not yet completely understood. For localization of Al in root tips, fluorescent dyes and laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) were compared. The staining of Al with morin is an appropriate means to study qualitatively the radial distribution along the root tip axis of Al which is complexed by oxalate and citrate in buckwheat roots. The results compare well with the distribution of total Al determined by LA-ICP-MS which could be reliably calibrated to compare with Al contents by conventional total Al determination using graphite furnace atomic absorption spectrometry. The Al localization in root cross-sections along the root tip showed that in buckwheat Al is highly mobile in the radial direction. The root apex predominantly accumulated Al in the cortex. The subapical root section showed a homogenous Al distribution across the whole section. In the following root section Al was located particularly in the pericycle and the xylem parenchyma cells. With further increasing distance from the root apex Al could be detected only in individual xylem vessels. The results support the view that the 10 mm apical root tip is the main site of Al uptake into the symplast of the cortex, while the subapical 10-20 mm zone is the main site of xylem loading through the pericycle and xylem parenchyma cells. Progress in the better molecular understanding of Al transport in buckwheat will depend on the consideration of the tissue specificity of Al transport and complexation.

  17. The effects of aluminium on plant growth in a temperate and deciduous aluminium accumulating species

    PubMed Central

    Schmitt, Marco; Watanabe, Toshihiro; Jansen, Steven

    2016-01-01

    Aluminium (Al) is a phytotoxic element affecting the growth and yield of many crop plants, especially in the tropics. Yet, some plants are able to accumulate high levels of Al. The monogeneric family Symplocaceae represents an Al accumulating family including many tropical and evergreen species with high Al levels in their above ground plant tissues. It is unclear, however, whether Al accumulation also characterises temperate species of Symplocos, and whether or not the uptake has a beneficial growth effect. Here, we investigate if the temperate, deciduous species Symplocos paniculata is able to accumulate Al by growing seedlings and saplings in a hydroponic setup at pH 4 with and without Al. Pyrocatechol-violet (PCV) and aluminon staining was performed to visualize Al accumulation in various plant tissues. Both seedlings and saplings accumulate Al in their tissues if available. Mean Al levels in leaves were 4107 (±1474 mg kg−1) and 4290 (±4025 mg kg−1) for the seedlings and saplings, respectively. The saplings treated without Al showed a high mortality rate unlike the Al accumulating ones. The seedlings, however, showed no difference in growth and vitality between the two treatments. The saplings treated with Al showed new twig, leaf and root development, resulting in a considerable biomass increase. PCV and aluminon staining indicated the presence of Al in leaf, wood and bark tissue of the plants. S. paniculata shares the capacity to accumulate Al with its tropical sister species and is suggested to be a facultative accumulator. Whether or not Al has a beneficial effect remains unclear, due to developmental differences between seedlings and saplings. Al is suggested to be transported via the xylem transport system into the leaves, which show the highest Al levels. Radial transport via ray parenchyma to bark tissue is also likely given the high Al concentrations in the bark tissue. PMID:27613876

  18. Aluminium localization in root tips of the aluminium-accumulating plant species buckwheat (Fagopyrum esculentum Moench)

    PubMed Central

    Klug, Benjamin; Specht, André; Horst, Walter J.

    2011-01-01

    Aluminium (Al) uptake and transport in the root tip of buckwheat is not yet completely understood. For localization of Al in root tips, fluorescent dyes and laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) were compared. The staining of Al with morin is an appropriate means to study qualitatively the radial distribution along the root tip axis of Al which is complexed by oxalate and citrate in buckwheat roots. The results compare well with the distribution of total Al determined by LA-ICP-MS which could be reliably calibrated to compare with Al contents by conventional total Al determination using graphite furnace atomic absorption spectrometry. The Al localization in root cross-sections along the root tip showed that in buckwheat Al is highly mobile in the radial direction. The root apex predominantly accumulated Al in the cortex. The subapical root section showed a homogenous Al distribution across the whole section. In the following root section Al was located particularly in the pericycle and the xylem parenchyma cells. With further increasing distance from the root apex Al could be detected only in individual xylem vessels. The results support the view that the 10 mm apical root tip is the main site of Al uptake into the symplast of the cortex, while the subapical 10–20 mm zone is the main site of xylem loading through the pericycle and xylem parenchyma cells. Progress in the better molecular understanding of Al transport in buckwheat will depend on the consideration of the tissue specificity of Al transport and complexation. PMID:21831842

  19. Copper and silver ion implantation of aluminium oxide-blasted titanium surfaces: proliferative response of osteoblasts and antibacterial effects.

    PubMed

    Fiedler, Jörg; Kolitsch, Andreas; Kleffner, Bernhard; Henke, Dietmar; Stenger, Steffen; Brenner, Rolf E

    2011-09-01

    Implant infection still represents a major clinical problem in orthopedic surgery. We therefore tested the in vitro biocompatibility and antibacterial effects of copper (Cu)- and silver (Ag)-ion implantation. Discs of a commonly used titanium alloy (Ti6AlV4) with an aluminium oxide-blasted surface were treated by Cu- or Ag-ion implantation with different dosage regimen (ranging from 1e15-17 ions cm(-2) at energies of 2-20 keV). The samples were seeded with primary human osteoblasts and cell attachment and proliferation was analyzed by an MTT-assay. In comparison to the reference titanium alloy there was no difference in the number of attached viable cells after two days. After seven days the number of viable cells was increased for Cu with 1e17 ions cm(-2) at 2 and 5 keV, and for Ag with 1e16 ions cm(-2) at 5 keV while it was reduced for the highest amount of Ag deposition (1e17 ions cm(-2) at 20 keV). Antibacterial effects on S.aureus and E.coli were marginal for the studied dosages of Cu but clearly present for Ag with 1e16 ions cm(-2) at 2 and 5 keV and 1e17 ions cm(-2) at 20 keV. These results indicate that Ag-ion implantation may be a promising methodological approach for antibacterial functionalization of titanium implants.

  20. Immuno-detection of aluminium and aluminium induced conformational changes in calmodulin--implications in Alzheimer's disease.

    PubMed

    Levi, R; Wolf, T; Fleminger, G; Solomon, B

    1998-12-01

    Binding of calcium to calmodulin (CAM) induces specific structural rearrangements in the whole protein molecule. Ca2+ organizes and stabilizes the four-domains structure of calmodulin in a helical, active conformation that can bind to its target proteins; the central helix remaining flexible is an essential condition for their bio-recognition. The conformation of calmodulin, and its efficacy to interact with target proteins, is profoundly altered when bound to metal ions other than calcium. As recently reported, the local structural changes of CaM, which occur upon aluminium binding, lead to the impairment of protein flexibility and to the loss of its ability to interact with several other proteins, which may decrease or inhibit the regulatory character of calmodulin. In this study we followed conformational changes occurring in the calmodulin molecule after aluminium binding using highly specific monoclonal antibodies (mAbs) able to differentiate between the conformational states of calmodulin, as well as mAbs which recognize aluminium free or bound to proteins. Under the same experimental conditions, mAb CAM-1, a Ca2+ conformation sensitive antibody raised against calmodulin, fails to recognize the calmodulin-aluminium complex, despite the presence of Ca2+, while the anti-Al antibodies show a maximal binding pattern towards their antigen. These data suggest that Al3+ ions bind to calmodulin in the presence of Ca2+ ions, leading to an inactive, reversible conformation, instead of its physiological active form. Alteration of the conformation of calmodulin imposed by Al binding may have possible implications in the neurotoxicity mechanism related to Alzheimer's disease.

  1. Investigation of the Icosahedral Z-Phase in Aluminium Transition Metal Alloys and Rapidly Solidified Al-Alloys

    DTIC Science & Technology

    1986-09-01

    Rev. Lett., 53, 1951 (1984). - A Script& NETALLURGICA Vol. 20, pp. 745-750, 1986 Pergamon Press Ltd. Printed in the U.S.A. All rights reserved...single- and two-sided jet polishing were utilized. In addition, some of the flakes were argon-ion . - - thinned using standard procedures. Subsequently...Reeied 26 Fabruay 198, accepted 14 April 1986) Electrohydrodynamic (EHD) atomization has boen used to rapidly solidify micron and submicron size

  2. Metal alloy identifier

    DOEpatents

    Riley, William D.; Brown, Jr., Robert D.

    1987-01-01

    To identify the composition of a metal alloy, sparks generated from the alloy are optically observed and spectrographically analyzed. The spectrographic data, in the form of a full-spectrum plot of intensity versus wavelength, provide the "signature" of the metal alloy. This signature can be compared with similar plots for alloys of known composition to establish the unknown composition by a positive match with a known alloy. An alternative method is to form intensity ratios for pairs of predetermined wavelengths within the observed spectrum and to then compare the values of such ratios with similar values for known alloy compositions, thereby to positively identify the unknown alloy composition.

  3. An evaluation of the pressure proof test concept for 2024-T3 aluminium alloy sheet

    NASA Technical Reports Server (NTRS)

    Dawicke, D. S.; Poe, C. C., Jr.; Newman, J. C.; Harris, C. E.

    1991-01-01

    The concept of pressure proof testing of fuselage structures with fatigue cracks to insure structural integrity was evaluated from a fracture mechanics viewpoint. A generic analytical and experimental investigation was conducted on uniaxially loaded flat panels with crack configurations and stress levels typical of longitudinal lap splice joints in commercial transport aircraft fuselages. The results revealed that the remaining fatigue life after a proof cycle was longer than that without the proof cycle because of crack growth retardation due to increased crack closure. However, based on a crack length that is slightly less than the critical value at the maximum proof stress, the minimum assured life or proof test interval must be no more than 550 pressure cycles for a 1.33 proof factor and 1530 pressure cycles for a 1.5 proof factor to prevent in-flight failures.

  4. Effect of Test Parameters on the Friction Behaviour of Anodized Aluminium Alloy

    PubMed Central

    Khalladi, A.; Elleuch, K.; De-Petris Wery, M.; Ayedi, H. F.

    2014-01-01

    The tribological behaviour of anodic oxide layer formed on Al5754, used in automotive applications, was investigated against test parameters. The friction coefficient under different normal loads, sliding speeds, and oxide thicknesses was studied using a pin on disc tribometer. Results show that the increase of load and sliding speed increase the friction coefficient. The rise of contact pressure and temperature seems to cause changes in wear mechanism. Glow-discharge optical emission spectroscopy (GDOES) was used to investigate the chemical composition of the oxide layer. Morphology and composition of the wear tracks were analyzed by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). On the basis of these characterization techniques, a wear mechanism was proposed. The observed mechanical properties can be related to the morphology and the chemical composition of the layer. PMID:27437452

  5. Optimising sulfuric acid hard coat anodising for an Al-Mg-Si wrought aluminium alloy

    NASA Astrophysics Data System (ADS)

    Bartolo, N.; Sinagra, E.; Mallia, B.

    2014-06-01

    This research evaluates the effects of sulfuric acid hard coat anodising parameters, such as acid concentration, electrolyte temperature, current density and time, on the hardness and thickness of the resultant anodised layers. A small scale anodising facility was designed and set up to enable experimental investigation of the anodising parameters. An experimental design using the Taguchi method to optimise the parameters within an established operating window was performed. Qualitative and quantitative methods of characterisation of the resultant anodised layers were carried out. The anodised layer's thickness, and morphology were determined using a light optical microscope (LOM) and field emission gun scanning electron microscope (FEG-SEM). Hardness measurements were carried out using a nano hardness tester. Correlations between the various anodising parameters and their effect on the hardness and thickness of the anodised layers were established. Careful evaluation of these effects enabled optimum parameters to be determined using the Taguchi method, which were verified experimentally. Anodised layers having hardness varying between 2.4-5.2 GPa and a thickness of between 20-80 μm were produced. The Taguchi method was shown to be applicable to anodising. This finding could facilitate on-going and future research and development of anodising, which is attracting remarkable academic and industrial interest.

  6. Simulation of defects in micro-deep drawing of an aluminium alloy foil

    NASA Astrophysics Data System (ADS)

    Hadi, Syamsul; YU, Hai-liang; TIEU, Kiet; Lu, Cheng

    2013-05-01

    Micro-forming refers to the application of conventional forming processes to manufacture products from ultra-thin sheet materials. While attempting to meet the increasing demand for cost-effective manufacturing of micro-formed components, it is very important to reduce the defects in the products. In this paper, we report a number of Finite Element (FE) simulations of the micro-deep drawing process with various sample thicknesses and eccentric distances. The simulations indicated that when the sample thickness is nearly equal to the gap between the plunger and the die, the sample is likely to develop fractures at the bottom corner. When the sample thickness is much smaller than the gap, wrinkling appears in the sample. If the sheet thickness is reduced, the wrinkles approach the bending zone. If the punch-die eccentricity is increased, the pressing process results in a defective product. The simulation results compared well with experimental results. This suggests that the computer simulations can be used to design future experiments.

  7. Resistance Spot Weld Failure Mode and Weld Performance for Aluminium Alloys

    SciTech Connect

    Sun, Xin

    2010-01-30

    In this chapter, we present the strength and failure modes of reactive NanoFoil® bonded joints for similar and dissimilar lightweight materials. NanoFoil® is a multi-layer foil fabricated through the growth of thousands of nanoscale layers of aluminum and nickel by vapor deposition. Initiated by an energy impulse, the like-like bonds of the atoms of each layer in the foil are exchanged for more stable unlike bonds between atoms from neighboring layers. As the atoms of each layer mix, heat is generated, creating a self-sustaining reaction traveling along the length of the foil. The instantaneous release of heat energy by this reaction is controlled by the nanolayer thickness and lay-up, such that accurate control of a highly localized heat source can be realized, allowing bonding without compromising the properties/integrities of the base materials. First, solder and braze joints for similar and dissimilar material combinations of steel, aluminum and magnesium are fabricated. Static bond strength tests under tensile shear loading condition are then performed to quantify the bond strength for different material combinations. The through-thickness microstructure changes and modifications by the bonding process are quantified using SEM. Depending on the base material combinations, it is shown that the nanofoil bond strength is comparable to those of the conventional structural adhesive bonds.

  8. Analysing the strength of friction stir spot welded joints of aluminium alloy by fuzzy logic

    NASA Astrophysics Data System (ADS)

    Vaira Vignesh, R.; Padmanaban, R.; Arivarasu, M.; Karthick, K. P.; Abirama Sundar, A.; Gokulachandran, J.

    2016-09-01

    Friction stir spot welding (FSSW) is a recent joining technique developed for spot welding of thin metal sheets. This process currently finds application in automotive, aerospace, marine and sheet metal industry. In this work, the effect of FSSW process parameters namely tool rotation speed, shoulder diameter and dwell time on Tensile shear failure load (TSFL) is investigated. Box-Behnken design is selected for conducting experiments. Fuzzy based soft computing is used to develop a model for TSFL of AA6061 joints fabricated by FSSW. The interaction of the process parameters on TSFL is also presented.

  9. Fatigue failure of an open cell and a closed cell aluminium alloy foam

    SciTech Connect

    Harte, A.M.; Fleck, N.A.; Ashby, M.F. . Engineering Dept.)

    1999-06-22

    The tension-tension and compression-compression cyclic properties are measured for an open cell Duocel foam of composition Al 6101-T6, and a closed cell Alporas foam of composition Al-5Ca-3Ti (wt%). the Duocel foam has a relatively uniform microstructure, and undergoes homogeneous straining in both monotonic and fatigue tests. In contrast, the Alporas foam is more irregular in microstructure, and exhibits crush-band formation at random locations under uniaxial compression; in compression-compression fatigue, a single crush band forms and broadens with additional fatigue cycles. Progressive shortening of the specimen in compression-compression fatigue, and progressive lengthening in tension-tension fatigue are due to a combination of low cycle fatigue failure and cyclic ratchetting. S-N fatigue curves are presented for the onset of progressive shortening in the compression tests, and material separation in the tension tests; it is envisaged that such curves will be of practical use in design.

  10. Investigations of the Electronic Properties and Surface Structures of Aluminium-Rich Quasicrystalline Alloys

    SciTech Connect

    Barrow, Jason A.

    2003-01-01

    The work presented in this dissertation has investigated three distinct areas of interest in the field of quasicrystals: bulk structure, transport properties, and electronic structure. First, they have described the results of a study which explored the fundamental interactions between the atomic species of the icosahedral Al-Pd-Mn quasicrystal. The goal of this work was to determine whether the pseudo-MacKay or Bergman type clusters have a special stability or are merely a geometric coincidence. This was carried out by using laser vaporization to produce gas-phase metal clusters, which were analyzed using time-of-flight mass spectrometry. Both the kinetic and thermodynamic stabilities of the clusters were probed. The data indicated no special stability for either pseudo-MacKay or Bergman type clusters as isolated units. This, however, is not proof that these clusters are simply a geometric coincidence. It is possible that such clusters only have stability in the framework of the bulk matrix and do not exist as isolated units. Next, they have reported their investigations of the bulk thermal transport properties of a decagonal Al-Ni-Co two dimensional quasicrystal in the temperature range 373K-873K. The properties of a sample oriented along the periodic axis and another oriented along the aperiodic axis were measured. A high degree of anisotropy was observed between the aperiodic and periodic directions. Additionally, the properties were measured for a sample miscut to an orientation 45° off-axis. The properties of the miscut sample were shown to have good agreement with a theoretical model used to describe thermal transport in metallic single crystals. This model only considers thermal transport by a free-electron gas; therefore, agreement with experimental data suggests the validity of the Drude free-electron model for the decagonal Al-Ni-Co at these temperatures. Consequently, the observed anisotropy may be adequately described using classical transport equations. Transport behavior is described in terms of charge carriers and the mean-free time between carrier collisions. It is concluded that the mean-free time is much longer in the periodic direction than in the aperiodic direction. This difference produces the observed anisotropy in thermal transport. The third study presented a detailed analysis of the reversible, sputter-induced phase transformation which occurs on the 5-fold surface of an icosahedral Al-Cu-Fe quasicrystal. Reflection high-energy electron diffraction (RHEED), x-ray photoemission spectroscopy (XPS), and ultra-violet photoemission spectroscopy (UPS) data were collected as a function of annealing temperature and were used to probe surface structure, surface composition, and electronic structure, respectively. The composition and structure of the sputtered surface are consistent with a transformation to the β-Al-Cu-Fe cubic structure, and shows a sharp metallic cut-off in the spectral intensity of the electronic structure at the Fermi edge. Upon annealing the surface reverts to a quasicrystalline composition and structure. This transformation has been correlated with a reduction in the spectral intensity of the electronic structure at the Fermi level. This data clearly demonstrates that the observed reduction is intrinsic to a quasicrystalline surface. It is concluded that this is due to the opening of a pseudo-gap in the electronic density of states as the surface reverts from β-Al-Cu-Fe to quasicrystalline.

  11. Influence of particle size on Cutting Forces and Surface Roughness in Machining of B4Cp - 6061 Aluminium Matrix Composites

    NASA Astrophysics Data System (ADS)

    Hiremath, Vijaykumar; Badiger, Pradeep; Auradi, V.; Dundur, S. T.; Kori, S. A.

    2016-02-01

    Amongst advanced materials, metal matrix composites (MMC) are gaining importance as materials for structural applications in particular, particulate reinforced aluminium MMCs have received considerable attention due to their superior properties such as high strength to weight ratio, excellent low-temperature performance, high wear resistance, high thermal conductivity. The present study aims at studying and comparing the machinability aspects of B4Cp reinforced 6061Al alloy metal matrix composites reinforced with 37μm and 88μm particulates produced by stir casting method. The micro structural characterization of the prepared composites is done using Scanning Electron Microscopy equipped with EDX analysis (Hitachi Su-1500 model) to identify morphology and distribution of B4C particles in the 6061Al matrix. The specimens are turned on a conventional lathe machine using a Polly crystalline Diamond (PCD) tool to study the effect of particle size on the cutting forces and the surface roughness under varying machinability parameters viz., Cutting speed (29-45 m/min.), Feed rate (0.11-0.33 mm/rev.) and depth of cut (0.5-1mm). Results of micro structural characterization revealed fairly uniform distribution of B4C particles (in both cases i.e., 37μm and 88μm) in 6061Al matrix. The surface roughness of the composite is influenced by cutting speed. The feed rate and depth of cut have a negative influence on surface roughness. The cutting forces decreased with increase in cutting speed whereas cutting forces increased with increase in feed and depth of cut. Higher cutting forces are noticed while machining Al6061 base alloy compared to reinforced composites. Surface finish is high during turning of the 6061Al base alloy and surface roughness is high with 88μm size particle reinforced composites. As the particle size increases Surface roughness also increases.

  12. Chronic Toxicity of Aluminium in Rats and Mice and its Effects on Phosphorous Metabolism

    PubMed Central

    Ondreička, R.; Ginter, E.; Kortus, J.

    1966-01-01

    In mice the oral LD50 values of aluminium chloride and aluminium sulphate were 0·77 ± 0·12 and 0·98 ± 0·09 g. Al/kg. (± S.E.) respectively. Mice and rats were fed on a normal diet containing about 170 p.p.m. of aluminium. Doubling this concentration caused a decrease in growth in the second and third generations of mice. A high intake of aluminium sulphate (2,835 p.p.m.) caused a 20-fold increase of aluminium retention in white rats. Aluminium accumulated in various tissues, especially in the skeleton, liver, and testes. A high rate of intake (2,665 p.p.m.) caused a negative phosphorus balance in the rat, with an increased output of phosphorus in the faeces. The lower absorption of phosphorus was also demonstrated with Na2H32PO4. Chronic and acute poisoning by aluminium chloride caused, after intraperitoneal Na2H32PO4, decreased incorporation of 32P into the phospholipids and nucleic acids of various tissues in the rat. It also caused a fall in the adenosinetriphosphate acid-levels in plasma, and a rise in the adenosine diphosphate level. The results suggest that the toxic effects of aluminium salts result both from decreased absorption of phosphorus and from interference with phosphorylation processes in the tissues. PMID:5926895

  13. Insight into the cellular fate and toxicity of aluminium adjuvants used in clinically approved human vaccinations.

    PubMed

    Mold, Matthew; Shardlow, Emma; Exley, Christopher

    2016-08-12

    Aluminium adjuvants remain the most widely used and effective adjuvants in vaccination and immunotherapy. Herein, the particle size distribution (PSD) of aluminium oxyhydroxide and aluminium hydroxyphosphate adjuvants was elucidated in attempt to correlate these properties with the biological responses observed post vaccination. Heightened solubility and potentially the generation of Al(3+) in the lysosomal environment were positively correlated with an increase in cell mortality in vitro, potentially generating a greater inflammatory response at the site of simulated injection. The cellular uptake of aluminium based adjuvants (ABAs) used in clinically approved vaccinations are compared to a commonly used experimental ABA, in an in vitro THP-1 cell model. Using lumogallion as a direct-fluorescent molecular probe for aluminium, complemented with transmission electron microscopy provides further insight into the morphology of internalised particulates, driven by the physicochemical variations of the ABAs investigated. We demonstrate that not all aluminium adjuvants are equal neither in terms of their physical properties nor their biological reactivity and potential toxicities both at the injection site and beyond. High loading of aluminium oxyhydroxide in the cytoplasm of THP-1 cells without immediate cytotoxicity might predispose this form of aluminium adjuvant to its subsequent transport throughout the body including access to the brain.

  14. Insight into the cellular fate and toxicity of aluminium adjuvants used in clinically approved human vaccinations

    PubMed Central

    Mold, Matthew; Shardlow, Emma; Exley, Christopher

    2016-01-01

    Aluminium adjuvants remain the most widely used and effective adjuvants in vaccination and immunotherapy. Herein, the particle size distribution (PSD) of aluminium oxyhydroxide and aluminium hydroxyphosphate adjuvants was elucidated in attempt to correlate these properties with the biological responses observed post vaccination. Heightened solubility and potentially the generation of Al3+ in the lysosomal environment were positively correlated with an increase in cell mortality in vitro, potentially generating a greater inflammatory response at the site of simulated injection. The cellular uptake of aluminium based adjuvants (ABAs) used in clinically approved vaccinations are compared to a commonly used experimental ABA, in an in vitro THP-1 cell model. Using lumogallion as a direct-fluorescent molecular probe for aluminium, complemented with transmission electron microscopy provides further insight into the morphology of internalised particulates, driven by the physicochemical variations of the ABAs investigated. We demonstrate that not all aluminium adjuvants are equal neither in terms of their physical properties nor their biological reactivity and potential toxicities both at the injection site and beyond. High loading of aluminium oxyhydroxide in the cytoplasm of THP-1 cells without immediate cytotoxicity might predispose this form of aluminium adjuvant to its subsequent transport throughout the body including access to the brain. PMID:27515230

  15. Aluminium based adjuvants and their effects on mitochondria and lysosomes of phagocytosing cells.

    PubMed

    Ohlsson, Lars; Exley, Christopher; Darabi, Anna; Sandén, Emma; Siesjö, Peter; Eriksson, Håkan

    2013-11-01

    Aluminium oxyhydroxide, Al(OH)3 is one of few compounds approved as an adjuvant in human vaccines. However, the mechanism behind its immune stimulating properties is still poorly understood. In vitro co-culture of an aluminium adjuvant and the human monocytic cell line THP-1 resulted in reduced cell proliferation. Inhibition occurred at concentrations of adjuvant several times lower than would be found at the injection site using a vaccine formulation containing an aluminium adjuvant. Based on evaluation of the mitochondrial membrane potential, THP-1 cells showed no mitochondrial rupture after co-culture with the aluminium adjuvant, instead an increase in mitochondrial activity was seen. The THP-1 cells are phagocytosing cells and after co-culture with the aluminium adjuvant the phagosomal pathway was obstructed. Primary or early phagosomes mature into phagolysosomes with an internal pH of 4.5 - 5 and carry a wide variety of hydrolysing enzymes. Co-culture with the aluminium adjuvant yielded a reduced level of acidic vesicles and cathepsin L activity, a proteolytic enzyme of the phagolysosomes, was almost completely inhibited. THP-1 cells are an appropriate in vitro model in order to investigate the mechanism behind the induction of a phagocytosing antigen presenting cell into an inflammatory cell by aluminium adjuvants. Much information will be gained by investigating the phagosomal pathway and what occurs inside the phagosomes and to elucidate the ultimate fate of phagocytosed aluminium particles.

  16. Dietary exposure to aluminium of urban residents from cities in South China.

    PubMed

    Jiang, Qi; Wang, Jing; Li, Min; Liang, Xuxia; Dai, Guangwei; Hu, Zhikun; Wen, Jian; Huang, Qiong; Zhang, Yonghui

    2013-01-01

    A dietary survey was conducted over three consecutive days by using 24-hour dietary recall in the Pearl River Delta of South China to investigate the dietary consumption status. A total of 1702 food samples, 22 food groups, were collected, and aluminium concentrations of foods were determined by using ICP-MS. Weekly dietary exposure to aluminium of the average urban residents of South China was estimated to be 1.5 mg kg⁻¹ body weight, which amounted to 76% of the provisional tolerable weekly intake. Wheat-made products (53.5%) contributed most to the dietary exposure, followed by vegetables (12.2%). The high-level consumers' weekly exposure to aluminium was 11.1 mg kg⁻¹ body weight, which amounted to 407% of the provisional tolerable weekly intake. The results indicated that the general urban residents in South China might be safe from aluminium exposure, but the high-level consumers might be at some risk of aluminium exposure. The foods contributing to aluminium exposure were processed food with aluminium-containing food additives. It is necessary to take effective measures to control the overuse of aluminium-containing food additives.

  17. Insight into the cellular fate and toxicity of aluminium adjuvants used in clinically approved human vaccinations

    NASA Astrophysics Data System (ADS)

    Mold, Matthew; Shardlow, Emma; Exley, Christopher

    2016-08-01

    Aluminium adjuvants remain the most widely used and effective adjuvants in vaccination and immunotherapy. Herein, the particle size distribution (PSD) of aluminium oxyhydroxide and aluminium hydroxyphosphate adjuvants was elucidated in attempt to correlate these properties with the biological responses observed post vaccination. Heightened solubility and potentially the generation of Al3+ in the lysosomal environment were positively correlated with an increase in cell mortality in vitro, potentially generating a greater inflammatory response at the site of simulated injection. The cellular uptake of aluminium based adjuvants (ABAs) used in clinically approved vaccinations are compared to a commonly used experimental ABA, in an in vitro THP-1 cell model. Using lumogallion as a direct-fluorescent molecular probe for aluminium, complemented with transmission electron microscopy provides further insight into the morphology of internalised particulates, driven by the physicochemical variations of the ABAs investigated. We demonstrate that not all aluminium adjuvants are equal neither in terms of their physical properties nor their biological reactivity and potential toxicities both at the injection site and beyond. High loading of aluminium oxyhydroxide in the cytoplasm of THP-1 cells without immediate cytotoxicity might predispose this form of aluminium adjuvant to its subsequent transport throughout the body including access to the brain.

  18. Potentiometric determination of the 'formal' hydrolysis ratio of aluminium species in aqueous solutions.

    PubMed

    Fournier, Agathe C; Shafran, Kirill L; Perry, Carole C

    2008-01-21

    The 'formal' hydrolysis ratio (h = C(OH-)added/C(Al)total) of hydrolysed aluminium-ions is an important parameter required for the exhaustive and quantitative speciation-fractionation of aluminium in aqueous solutions. This paper describes a potentiometric method for determination of the formal hydrolysis ratio based on an automated alkaline titration procedure. The method uses the point of precipitation of aluminium hydroxide as a reference (h = 3.0) in order to calculate the initial formal hydrolysis ratio of hydrolysed aluminium-ion solutions. Several solutions of pure hydrolytic species including aluminium monomers (AlCl3), Al13 polynuclear cluster ([Al13O4(OH)24(H2O)12]7+), Al30 polynuclear cluster ([Al30O8(OH)56(H2O)26]18+) and a suspension of nanoparticulate aluminium hydroxide have been used as 'reference standards' to validate the proposed potentiometric method. Other important variables in the potentiometric determination of the hydrolysis ratio have also been optimised including the concentration of aluminium and the type and strength of alkali (Trizma-base, NH3, NaHCO3, Na2CO3 and KOH). The results of the potentiometric analysis have been cross-verified by quantitative 27Al solution nuclear magnetic resonance (27Al NMR) measurements. The 'formal' hydrolysis ratio of a commercial basic aluminium chloride has been measured as an example of a practical application of the developed technique.

  19. The chemical transformation of copper in aluminium oxide during heating

    NASA Astrophysics Data System (ADS)

    Wei, Yu-Ling; Wang, Hsi-Chih; Yang, Yaw-Wen; Lee, Jyh-Fu

    2004-08-01

    Thermal treatment has recently been emerging as a promising environmental technology to stabilize heavy metal-containing industrial sludge. This study used x-ray absorption spectroscopy (XAS) to identify the species of copper contaminant contained in aluminium oxide that is one of the main compositions of sludge and soil. Results indicate that the originally loaded copper nitrate was transformed into Cu(OH)2 after its dissolution in the aluminium oxide slurry. Extended x-ray absorption fine structure (EXAFS) fitting indicates that the main copper species in the 105 °C dried Cu(NO3)2-loaded aluminium oxide is Cu(OH)2 which accounts for ca. 75% of the loaded copper. After thermal treatment at 500 °C for 1 h, both x-ray absorption near-edge structure (XANES) and EXAFS fitting results show that CuO became the prevailing copper species (about 85%); the rest of the copper consisted of {\\sim }15{%} Cu(OH)2 and a negligible amount of Cu(NO3)2. It was found that most Cu(OH)2 and Cu(NO3)2 decomposed into CuO at 500 °C. Further increase of the heating temperature from 500 to 900 °C resulted in more decomposition of Cu(OH)2 and Cu(NO3)2; therefore CuO remained as the main copper species. However, it was suggested that about 15% of the loaded copper formed CuAl2O4 through the chemical reaction between CuO and Al2O3 at 900 °C.

  20. Blood plasma contact activation on silicon, titanium and aluminium.

    PubMed

    Arvidsson, Sara; Askendal, Agneta; Tengvall, Pentti

    2007-03-01

    In the present work, blood plasma protein deposition to spontaneously air oxidized silicon, titanium and aluminium was re-investigated in vitro. Immunological- and null ellipsometry methods were used to detect and quantitate adsorbed proteins, RIA methods to study the retention of preadsorbed 125I-HSA upon exposure to buffer or blood plasma, and kallikrein-specific colorimetric substrate S-2302 to follow the surface generation of kallikrein. The results show that the contact activation of coagulation and complement systems are connected on Si and Ti, but not on Al, via coagulation factor XII. Preadsorbed 125I-HSA was most readily displaced on silicon, followed by titanium and aluminium. The surfaces displayed different antibody binding patterns after short and long-time exposures to plasma. Titanium and silicon bound anti-HMWK after 1 min in plasma, but aluminium did not. When the plasma incubation time was prolonged up to 2h the anti-HMWK binding disappeared totally on titanium and decreased on silicon. During the same time period, anti-C3c binding increased to the three types of surfaces. Also, the anti-C3c binding onto Si and Ti, but not Al, disappeared after incubation in Factor XII deficient plasma or when a specific coagulation factor XII (Factor XII) inhibitor, corn trypsin inhibitor (CTI) was added to normal plasma. The surface contacted plasmas cleaved the kallikrein-specific reagent S-2302 both after single surface contact, and after reincubation of surfaces in fresh plasma. The results show that C3b and Factor XIIa and their degradation products were retained at the surfaces.

  1. Ultraviolet Plasmonic Aluminium Nanoparticles for Highly Efficient Light Incoupling on Silicon Solar Cells

    PubMed Central

    Zhang, Yinan; Cai, Boyuan; Jia, Baohua

    2016-01-01

    Plasmonic metal nanoparticles supporting localized surface plasmon resonances have attracted a great deal of interest in boosting the light absorption in solar cells. Among the various plasmonic materials, the aluminium nanoparticles recently have become a rising star due to their unique ultraviolet plasmonic resonances, low cost, earth-abundance and high compatibility with the complementary metal-oxide semiconductor (CMOS) manufacturing process. Here, we report some key factors that determine the light incoupling of aluminium nanoparticles located on the front side of silicon solar cells. We first numerically study the scattering and absorption properties of the aluminium nanoparticles and the influence of the nanoparticle shape, size, surface coverage and the spacing layer on the light incoupling using the finite difference time domain method. Then, we experimentally integrate 100-nm aluminium nanoparticles on the front side of silicon solar cells with varying silicon nitride thicknesses. This study provides the fundamental insights for designing aluminium nanoparticle-based light trapping on solar cells. PMID:28335223

  2. Ultraviolet Plasmonic Aluminium Nanoparticles for Highly Efficient Light Incoupling on Silicon Solar Cells.

    PubMed

    Zhang, Yinan; Cai, Boyuan; Jia, Baohua

    2016-05-24

    Plasmonic metal nanoparticles supporting localized surface plasmon resonances have attracted a great deal of interest in boosting the light absorption in solar cells. Among the various plasmonic materials, the aluminium nanoparticles recently have become a rising star due to their unique ultraviolet plasmonic resonances, low cost, earth-abundance and high compatibility with the complementary metal-oxide semiconductor (CMOS) manufacturing process. Here, we report some key factors that determine the light incoupling of aluminium nanoparticles located on the front side of silicon solar cells. We first numerically study the scattering and absorption properties of the aluminium nanoparticles and the influence of the nanoparticle shape, size, surface coverage and the spacing layer on the light incoupling using the finite difference time domain method. Then, we experimentally integrate 100-nm aluminium nanoparticles on the front side of silicon solar cells with varying silicon nitride thicknesses. This study provides the fundamental insights for designing aluminium nanoparticle-based light trapping on solar cells.

  3. Effects of silicon on gastrointestinal absorption of aluminium

    SciTech Connect

    Edwardson, J.A.; Moore, P.B.; Ferrier, I.N.; Lilley, J.S.; Newton, G.W.A.; Barker, J.; Templar, J.; Day, J.P.

    1993-07-24

    The reported geographical association between Alzheimer's disease and levels of aluminium (Al) in water supplies may reflect the inverse relation between Al and silicon (Si) concentrations in water, and the potential for Si to reduce the bioavailability of the metal. The authors tested this hypothesis using isotopic [sup 26]Al tracer administered orally to five healthy volunteers in the presence and absence of Si. Dissolved Si, at a concentration found in some water supplies reduced the peak plasma [sup 26]Al concentration to 15% of the value obtained in the absence of Si. The results indicate that dissolved Si is an important factor in limiting the absorption of dietary Al.

  4. Mechanism of aluminium bio-mineralization in the apoferritin cavity

    NASA Astrophysics Data System (ADS)

    Chiarpotto, M.; Ciasca, G.; Vassalli, M.; Rossi, C.; Campi, G.; Ricci, A.; Bocca, B.; Pino, A.; Alimonti, A.; De Sole, P.; Papi, M.

    2013-08-01

    Many experimental evidences point out the correlation between the presence of aluminum-ferritin complex and neursopathological disorders. In these complexes, two different ranges of Aluminium (Al) atoms are usually found, i.e., just few atoms or several hundreds. Here, we investigated the in-vitro Al-apoferritin binding, with the aim to elucidate the mechanism behind the formation of Al-ferritin complexes in-vivo. To this purpose, we studied the mineralization of Al in its ionic and complexed form with citrate demonstrating that high Al levels found in clinical studies can be obtained only conveying Al by small physiological ligands.

  5. Histological and electron microprobe studies of mineralisation in aluminium-related osteomalacia.

    PubMed Central

    Boyce, B. F.; Byars, J.; McWilliams, S.; Mocan, M. Z.; Elder, H. Y.; Boyle, I. T.; Junor, B. J.

    1992-01-01

    AIMS: To determine a possible mechanism to explain the presence of aluminium lines within fully calcified bone in aluminium-related osteomalacia. METHODS: Fifty five bone cases shown by bone biopsy to be aluminium-related osteomalacia were studied. In 38 specimens aluminium lines were identified within calcified bone by means of the Aluminon stain and a characteristic form of patchy mineralisation was seen within thickened osteoid seams. Five representative examples were analysed quantitatively by histomorphometry and electronprobe X-ray microanalysis and compared with five cases of vitamin D deficiency-related osteomalacia which also had patchy mineralisation. RESULTS: The patchy calcification occupied 40 +/- 8% (mean +/- SEM) of the osteoid and consisted of small focal deposits (less than 40 microns diameter), often (52%) around osteoid osteocytes (probably an underestimate of the association), and larger areas that extended to the aluminium lines at the underlying mineralisation front. Small and large mineralisation nuclei were seen ultrastructurally in the patchy calcification. Quantitative electronprobe X-ray microanalysis showed that calcium concentrations and calcium:phosphorus ratios in the mineralisation nuclei and in the superficial layer of the fully calcified bone of the aluminium-related osteomalacia cases were significantly less than values measured at similar sites in the vitamin D deficiency-related osteomalacia cases. Furthermore, aluminium could not be detected by means of this technique at the mineralisation front or along cement lines in these specimens. CONCLUSIONS: Calcification can occur in thickened osteoid seams in osteomalacia. It can begin around osteoid osteocytes as small deposits that enlarge within the osteoid and extend to the underlying mineralisation front or cement line where aluminium lines may become trapped. Complete calcification of osteoid could account for the presence of aluminium lines within fully calcified bone. The

  6. A parametric study of surface roughness and bonding mechanisms of aluminum alloys with epoxies: a molecular dynamics simulation

    NASA Astrophysics Data System (ADS)

    Timilsina, Rajendra; Termaath, Stephanie

    The marine environment is highly aggressive towards most materials. However, aluminium-magnesium alloys (Al-Mg, specifically, 5xxx series) have exceptionally long service life in such aggressive marine environments. For instance, an Al-Mg alloy, AA5083, is extensively used in naval structures because of its good mechanical strength, formability, seawater corrosion resistance and weldability. However, bonding mechanisms of these alloys with epoxies in a rough surface environment are not fully understood yet. It requires a rigorous investigation at molecular or atomic levels. We performed a molecular dynamics simulation to study an adherend surface preparation and surface bonding mechanisms of Al-Mg alloy (AA5083) with different epoxies by developing several computer models. Various distributions of surface roughness are introduced in the models and performed molecular dynamics simulations. Formation of a beta phase (Al3Mg2) , microstructures, bonding energies at the interface, bonding strengths and durability are investigated. Office of Naval Research.

  7. Precipitation Reactions in Age-Hardenable Alloys During Laser Additive Manufacturing

    NASA Astrophysics Data System (ADS)

    Jägle, Eric A.; Sheng, Zhendong; Wu, Liang; Lu, Lin; Risse, Jeroen; Weisheit, Andreas; Raabe, Dierk

    2016-03-01

    We describe and study the thermal profiles experienced by various age-hardenable alloys during laser additive manufacturing (LAM), employing two different manufacturing techniques: selective laser melting and laser metal deposition. Using scanning electron microscopy and atom probe tomography, we reveal at which stages during the manufacturing process desired and undesired precipitation reactions can occur in age-hardenable alloys. Using examples from a maraging steel, a nickel-base superalloy and a scandium-containing aluminium alloy, we demonstrate that precipitation can already occur during the production of the powders used as starting material, during the deposition of material (i.e. during solidification and subsequent cooling), during the intrinsic heat treatment effected by LAM (i.e. in the heat affected zones) and, naturally, during an ageing post-heat treatment. These examples demonstrate the importance of understanding and controlling the thermal profile during the entire additive manufacturing cycle of age-hardenable materials including powder synthesis.

  8. High temperature behavior of nanostructured Al powders obtained by mechanical alloying under NH3 flow

    NASA Astrophysics Data System (ADS)

    Caballero, E. S.; Cintas, J.; Cuevas, F. G.; Montes, J. M.; Herrera-García, M.

    2015-03-01

    Aluminium powder was mechanically alloyed under ammonia gas flow for different times (1-5 h) in order to produce a second-phase reinforcement, mainly by aluminium nitride (AlN). After milling, powders were consolidated by cold uniaxial pressing and vacuum sintering. A small amount of copper powder was added to the Al milled powder to improve its sintering behavior. Hardness and indirect tensile test were carried out at room and high temperature to evaluate the mechanical properties evolution. Results showed an remarkable hardness increase with the second phases content, even at high temperature (up to 229 HB at 400 °C). However, the high content of second phases of ceramic nature decreases the ductility, resulting in low values of tensile strength (lower than 160 MPa).

  9. Aluminium-oxide wires for superconducting high kinetic inductance circuits

    NASA Astrophysics Data System (ADS)

    Rotzinger, H.; Skacel, S. T.; Pfirrmann, M.; Voss, J. N.; Münzberg, J.; Probst, S.; Bushev, P.; Weides, M. P.; Ustinov, A. V.; Mooij, J. E.

    2017-02-01

    We investigate thin films of conducting aluminium-oxide, also known as granular aluminium, as a material for superconducting high quality, high kinetic inductance circuits. The films are deposited by an optimised reactive DC magnetron sputter process and characterised using microwave measurement techniques at milli-Kelvin temperatures. We show that, by precise control of the reactive sputter conditions, a high room temperature sheet resistance and therefore high kinetic inductance at low temperatures can be obtained. For a coplanar waveguide resonator with 1.5 kΩ sheet resistance and a kinetic inductance fraction close to unity, we measure a quality factor in the order of 700 000 at 20 mK. Furthermore, we observe a sheet resistance reduction by gentle heat treatment in air. This behaviour is exploited to study the kinetic inductance change using the microwave response of a coplanar wave guide resonator. We find the correlation between the kinetic inductance and the sheet resistance to be in good agreement with theoretical expectations.

  10. Aluminium chloride-induced toxicity in zebrafish larvae.

    PubMed

    Monaco, A; Grimaldi, M C; Ferrandino, I

    2016-08-15

    Embryos at shield stage and larvae at protruding mouth stage were exposed to different concentrations of aluminium chloride (AlCl3 ) for 72 h with the purpose to analyse their phenotype and lethality. After 24, 48 and 72 h of treatment, higher toxicity of the metal was observed on larvae with minimal lethal concentration of 0.25, 0.20 and 0.08 mm, respectively, while for embryos the corresponding values were 40, 25 and 16 mm. We observed pericardial oedema and alteration of heart rate in 50% of larvae after 48 h of exposure to 100 μm. In larvae exposed to the same concentration, there was also a neurological injury at the level of glial cells, with the number of glial fibrillary acidic protein-positive cells being significantly reduced. This study confirms the toxic nature of this metal and shows that aluminium could also interestingly represent a cardiotoxin in addition to its neurotoxic ability.

  11. Catalytic spectrophotometric determination of trace aluminium with indigo carmine.

    PubMed

    Zheng, Huai-Li; Xiong, Wen-Qiang; Gong, Ying-Kun; Peng, De-Jun; Li, Ling-Chun

    2007-04-01

    A new catalytic spectrophotometric method is described for the determination of trace amounts of Al(III). The methods based on catalytic action of Al(III) on the oxidation of indigo carmine (IC) by ammonium persulfate in hexamethylene tetramine-hydrochloric acid ((CH2)6N4-HCl) buffer medium (pH 5.4) and in the presence of surfactant-TritonX-100. The effects of some factors on the reaction speed were investigated. Aluminium concentration is linear for 0-1.2x10(-7) g/ml in this method. The detection limit of the proposed method is 1.96x10(-8) g/ml. Most of the foreign ions except for Cu(II), Fe(III) do not interfere with the determination, and the interference of Cu(II) and Fe(III) in this method can be removed by extraction with sodium diethyldithiocarbamate-carbon tetrachloride (DDTC-CCl4). This system is a quasi-zero-order reaction for Al(III), but it is a quasi-first-order reaction for IC. The apparent rate constant is 2.62x10(-5) s-1 and the apparent activation energy is 6.60 kJ/mol in the system. The proposed method was applied to the determination of trace aluminium(III) in real samples with satisfactory results.

  12. Cancellous bone homograft storage with aluminium-polyethylene bags.

    PubMed

    Meana, A; Martinez, R; Cañal, P; Arriaga, M J; Román, F San; Llames, S; Orós, C; Moreno, A; Fernandez, C

    2006-01-01

    In order to transport and cryopreserve human tissues, it is essential to have an easy-to-use recipient where tissues can be kept in sterile conditions. Here we show the results obtained by using Macopharma's tissue freezing bags, an aluminium-polyethylene multilayer bag, in our tissue bank of the Centro Comunitario de Sangre y Tejidos de Asturias. Five hundred and twenty-seven cancellous bone homografts were obtained from hospitals located 120 km around our Bank. The homografts were submitted to bacteriological controls and sent to our bank in these bags. They were stored at -70 degrees C and sent in dry ice to about 50 hospitals, where the tissue was bacteriologically controlled and grafted. Furthermore, the behaviour of these bags at -140 degrees C (vapour nitrogen) or -196 degrees C (liquid nitrogen) was tested. Our results indicate that Macopharma aluminium-polyethylene bags are suitable for the transporting and cryopreserving of cancellous bone homografts. These bags could also be used for keeping tissues in nitrogen containers.

  13. Atomistic calculations of dislocation core energy in aluminium

    DOE PAGES

    Zhou, X. W.; Sills, R. B.; Ward, D. K.; ...

    2017-02-16

    A robust molecular dynamics simulation method for calculating dislocation core energies has been developed. This method has unique advantages: it does not require artificial boundary conditions, is applicable for mixed dislocations, and can yield highly converged results regardless of the atomistic system size. Utilizing a high-fidelity bond order potential, we have applied this method in aluminium to calculate the dislocation core energy as a function of the angle β between the dislocation line and Burgers vector. These calculations show that, for the face-centred-cubic aluminium explored, the dislocation core energy follows the same functional dependence on β as the dislocation elasticmore » energy: Ec = A·sin2β + B·cos2β, and this dependence is independent of temperature between 100 and 300 K. By further analysing the energetics of an extended dislocation core, we elucidate the relationship between the core energy and radius of a perfect versus extended dislocation. With our methodology, the dislocation core energy can be accurately accounted for in models of plastic deformation.« less

  14. Atomistic calculations of dislocation core energy in aluminium

    NASA Astrophysics Data System (ADS)

    Zhou, X. W.; Sills, R. B.; Ward, D. K.; Karnesky, R. A.

    2017-02-01

    A robust molecular-dynamics simulation method for calculating dislocation core energies has been developed. This method has unique advantages: It does not require artificial boundary conditions, is applicable for mixed dislocations, and can yield converged results regardless of the atomistic system size. Utilizing a high-fidelity bond order potential, we have applied this method in aluminium to calculate the dislocation core energy as a function of the angle β between the dislocation line and the Burgers vector. These calculations show that, for the face-centered-cubic aluminium explored, the dislocation core energy follows the same functional dependence on β as the dislocation elastic energy: Ec=A sin2β +B cos2β , and this dependence is independent of temperature between 100 and 300 K. By further analyzing the energetics of an extended dislocation core, we elucidate the relationship between the core energy and the core radius of a perfect versus an extended dislocation. With our methodology, the dislocation core energy can accurately be accounted for in models of dislocation-mediated plasticity.

  15. Geopolymerisation of fly ashes with waste aluminium anodising etching solutions.

    PubMed

    Ogundiran, M B; Nugteren, H W; Witkamp, G J

    2016-10-01

    Combined management of coal combustion fly ash and waste aluminium anodising etching solutions using geopolymerisation presents economic and environmental benefits. The possibility of using waste aluminium anodising etching solution (AES) as activator to produce fly ash geopolymers in place of the commonly used silicate solutions was explored in this study. Geopolymerisation capacities of five European fly ashes with AES and the leaching of elements from their corresponding geopolymers were studied. Conventional commercial potassium silicate activator-based geopolymers were used as a reference. The geopolymers produced were subjected to physical, mechanical and leaching tests. The leaching of elements was tested on 28 days cured and crushed geopolymers using NEN 12457-4, NEN 7375, SPLP and TCLP leaching tests. After 28 days ambient curing, the geopolymers based on the etching solution activator showed compressive strength values between 51 and 84 MPa, whereas the commercial potassium silicate based geopolymers gave compressive strength values between 89 and 115 MPa. Based on the regulatory limits currently associated with the used leaching tests, all except one of the produced geopolymers (with above threshold leaching of As and Se) passed the recommended limits. The AES-geopolymer geopolymers demonstrated excellent compressive strength, although less than geopolymers made from commercial activator. Additionally, they demonstrated low element leaching potentials and therefore can be suitable for use in construction works.

  16. High current–density anodic electrodissolution in flow–injection systems for the determination of aluminium, copper and zinc in non–ferroalloys by flame atomic absorption spectrometry

    PubMed Central

    Giacomozzi, César Augusto; de Queiróz, Roldão R. U.; Souza, Ivan Gonçalves

    1999-01-01

    An automatic procedure with a high current-density anodic electrodissolution unit (HDAE) is proposed for the determination of aluminium, copper and zinc in non-ferroalloys by flame atomic absorption spectrometry, based on the direct solid analysis. It consists of solenoid valve-based commutation in a flow-injection system for on-line sample electro-dissolution and calibration with one multi-element standard, an electrolytic cell equipped with two electrodes (a silver needle acts as cathode, and sample as anode), and an intelligent unit. The latter is assembled in a PC-compatible microcomputer for instrument control, and for data acquisition and processing. General management of the process is achieved by use of software written in Pascal. Electrolyte compositions, flow rates, commutation times, applied current and electrolysis time were investigated. A 0.5 mol l-1 HN03 solution was elected as electrolyte and 300 A/cm2 as the continuous current pulse. The performance of the proposed system was evaluated by analysing aluminium in Al-alloy samples, and copper/zinc in brass and bronze samples, respectively. The system handles about 50 samples per hour. Results are precise (R.S.D. < 2%) and in agreement with those obtained by ICP-AES and spectrophotometry at a 95% confidence level. PMID:18924839

  17. Monte Carlo simulation of electron depth distribution and backscattering for carbon films deposited on aluminium as a function of incidence angle and primary energy

    NASA Astrophysics Data System (ADS)

    Dapor, Maurizio

    2005-01-01

    Carbon films are deposited on various substrates (polymers, polyester fabrics, polyester yarns, metal alloys) both for experimental and technological motivations (medical devices, biocompatible coatings, food package and so on). Computational studies of the penetration of electron beams in supported thin film of carbon are very useful in order to compare the simulated results with analytical techniques data (obtained by scanning electron microscopy and/or Auger electron spectroscopy) and investigate the film characteristics. In the present paper, the few keV electron depth distribution and backscattering coefficient for the special case of film of carbon deposited on aluminium are investigated, by a Monte Carlo simulation, as a function of the incidence angle and primary electron energy. The simulated results can be used as a way to evaluate the carbon film thickness by a set of measurements of the backscattering coefficient.

  18. Effects on the nervous system among welders exposed to aluminium and manganese.

    PubMed Central

    Sjögren, B; Iregren, A; Frech, W; Hagman, M; Johansson, L; Tesarz, M; Wennberg, A

    1996-01-01

    OBJECTIVES--The purpose was to study the effects on the nervous system in welders exposed to aluminium and manganese. METHODS--The investigation included questionnaires on symptoms, psychological methods (simple reaction time, finger tapping speed and endurance, digit span, vocabulary, tracking, symbol digit, cylinders, olfactory threshold, Luria-Nebraska motor scale), neurophysiological methods (electroencephalography, event related auditory evoked potential (P-300), brainstem auditory evoked potential, and diadochokinesometry) and assessments of blood and urine concentrations of metals (aluminium, lead, and manganese). RESULTS--The welders exposed to aluminium (n = 38) reported more symptoms from the central nervous system than the control group (n = 39). They also had a decreased motor function in five tests. The effect was dose related in two of these five tests. The median exposure of aluminium welders was 7065 hours and they had about seven times higher concentrations of aluminium in urine than the controls. The welders exposed to manganese (n = 12) had a decreased motor function in five tests. An increased latency of event related auditory evoked potential was also found in this group. The median manganese exposure was 270 hours. These welders did not have higher concentrations of manganese in blood than the controls. CONCLUSIONS--The neurotoxic effects found in the groups of welders exposed to aluminium and manganese are probably caused by the aluminium and manganese exposure, respectively. These effects indicate a need for improvements in the work environments of these welders. PMID:8563855

  19. Continuous flow analysis method for determination of soluble iron and aluminium in ice cores.

    PubMed

    Spolaor, A; Vallelonga, P; Gabrieli, J; Roman, M; Barbante, C

    2013-01-01

    Iron and aluminium are the two most abundant metals on the Earth's crust, but they display quite different biogeochemical properties. While iron is essential to many biological processes, aluminium has not been found to have any biological function at all. In environmental studies, iron has been studied in detail for its limiting role in the bioproductivity of high nutrient, low carbon oceanic zones, while aluminium is routinely used as a reference of crustal contributions to atmospheric deposition archives including peat bogs, lacustrine and marine sediments and ice sheets and glaciers. We report here the development of a flow injection analysis technique, which has been optimised for the simultaneous determination of soluble iron and aluminium in polar ice cores. Iron was determined by its catalytic role in the reduction of N,N-dimethyl-p-phenylenediamene (DPD) to a semiquinonic form (DPDQ) and subsequent absorption spectroscopy at 514 nm. Aluminium was determined by spectroscopic analysis of an aluminium-lumogallion complex that exhibits fluorescence at 560 nm. These techniques have been applied to a section of Greenland ice dated to 1729-1733 AD and indicate that volcanism is a source of highly soluble aluminium and iron.

  20. Bacopa monniera prevents from aluminium neurotoxicity in the cerebral cortex of rat brain.

    PubMed

    Jyoti, Amar; Sethi, Pallavi; Sharma, Deepak

    2007-04-20

    Bacopa monniera is a perennial herb, and is used as a nerve tonic in äyurveda, a traditional medicinal system in India. Aluminium-induced neurotoxicity is well known and different salts of aluminium have been reported to accelerate oxidative damage to biomolecules like lipids, proteins and nucleic acids. The objective of the present study was to investigate whether Bacopa monniera could potentially inhibit aluminium toxicity in the cerebral cortex. Male Wister rats (8 months old) were administered with AlCl(3) orally at a dose of 50mg/kg/day in drinking water for 1 month. Experimental rats were given AlCl(3) along with Bacopa monniera extract at a dose of 40 mg/kg/day. One group of rats was treated with l-deprenyl at a dose of 1mg/kg/day along with AlCl(3) treatment. We have observed that Bacopa monniera prevented accumulation of lipid and protein damage significantly, which resulted from aluminium intake. Decline in the activity of endogenous antioxidant enzymes associated with aluminium administration was also inhibited by Bacopa monniera extract. The potential of Bacopa monniera to inhibit Al-induced oxidative stress was observed to be similar to that of l-deprenyl, which was taken as standard. The potential of Bacopa monniera extract to prevent aluminium neurotoxicity was reflected at the microscopic level as well, indicative of its neuroprotective effects. These findings strongly implicate that Bacopa monniera has potential to protect brain from oxidative damage resulting from aluminium toxicity.

  1. Factors affecting the aluminium content of human femoral head and neck.

    PubMed

    Zioła-Frankowska, Anetta; Dąbrowski, Mikołaj; Kubaszewski, Łukasz; Rogala, Piotr; Frankowski, Marcin

    2015-11-01

    Tissues for the study were obtained intraoperatively during hip replacement procedures from 96 patients. In all the cases, the indication for this treatment was primary or secondary degenerative changes in the hip joint. The subject of the study was the head and neck of the femur, resected in situ. Aluminium concentrations measured in femoral head and neck samples from patients aged between 25 and 91 were varied. Statistical methods were applied to determine the variations in relation to the parameters from the background survey. Significant differences in the aluminium content of femoral head samples were observed between patients under and over 60 years of age. Based on the results, it was confirmed that the aluminium accumulates in bones over a lifetime. The study showed that the content of aluminium in the head and neck of the femur depends on the factors such as: type of medicines taken, contact with chemicals at work, differences in body anatomy and sex. The study on the levels of aluminium in bones and the factors affecting its concentration is a valuable source of information for further research on the role of aluminium in bone diseases. Based on the investigations, it was found that the GF-AAS technique is the best analytical tool for routine analysis of aluminium in complex matrix samples. The use of femoral heads in the investigations was approved by the Bioethics Committee of the University of Medical Sciences in Poznań (Poland).

  2. Aqueous aluminium eliminates Gyrodactylus salaris (Platyhelminthes, Monogenea) infections in Atlantic salmon.

    PubMed

    Soleng, A; Poléo, A B; Alstad, N E; Bakke, T A

    1999-07-01

    This study focuses on the effect of acidic water and aqueous aluminium on the monogenean ectoparasite Gyrodactylus salaris, infecting Atlantic salmon (Salmo salar) parr. G. salaris-infected salmon were exposed to various combinations of acidity and aluminium concentrations. The most pronounced effect was the elimination of parasites after 4 days when 202 micrograms Al/l was added to the water. The effect of aluminium was concentration dependent, but was relatively independent of pH (5.2, 5.6 and 5.9). At the lowest pH of 5.0 the effect of aluminium was enhanced. Acidic aluminium-poor water had no or minor effects on the G. salaris infections except at pH 5.0 where all parasites were eliminated within 9 days. The G. salaris populations increased exponentially in untreated control water. The results show for the first time that aqueous aluminium can, to a limited extent, have a positive effect on fish health. This study emphasizes that basic knowledge about abiotic environmental factors is of importance in order to understand the population dynamics, range extension and dispersal of ectoparasites such as G. salaris. Finally, our results suggest that aluminium treatment could form an effective disinfection method against ectoparasites in hatcheries and laboratories, as well as complementing the controversial rotenone treatments used against natural populations of G. salaris.

  3. Chemical mimicking of bio-assisted aluminium extraction by Aspergillus niger's exometabolites.

    PubMed

    Boriová, Katarína; Urík, Martin; Bujdoš, Marek; Pifková, Ivana; Matúš, Peter

    2016-11-01

    Presence of microorganisms in soils strongly affects mobility of metals. This fact is often excluded when mobile metal fraction in soil is studied using extraction procedures. Thus, the first objective of this paper was to evaluate strain Aspergillus niger's exometabolites contribution on aluminium mobilization. Fungal exudates collected in various time intervals during cultivation were analyzed and used for two-step bio-assisted extraction of alumina and gibbsite. Oxalic, citric and gluconic acids were identified in collected culture media with concentrations up to 68.4, 2.0 and 16.5 mmol L(-1), respectively. These exometabolites proved to be the most efficient agents in mobile aluminium fraction extraction with aluminium extraction efficiency reaching almost 2.2%. However, fungal cultivation is time demanding process. Therefore, the second objective was to simplify acquisition of equally efficient extracting agent by chemically mimicking composition of main organic acid components of fungal exudates. This was successfully achieved with organic acids mixture prepared according to medium composition collected on the 12th day of Aspergillus niger cultivation. This mixture extracted similar amounts of aluminium from alumina compared to culture medium. The aluminium extraction efficiency from gibbsite by organic acids mixture was lesser than 0.09% which is most likely because of more rigid mineral structure of gibbsite compared to alumina. The prepared organic acid mixture was then successfully applied for aluminium extraction from soil samples and compared to standard single step extraction techniques. This showed there is at least 2.9 times higher content of mobile aluminium fraction in soils than it was previously considered, if contribution of microbial metabolites is considered in extraction procedures. Thus, our contribution highlights the significance of fungal metabolites in aluminium extraction from environmental samples, but it also simplifies the

  4. Aluminium exposure from parenteral nutrition in preterm infants and later health outcomes during childhood and adolescence.

    PubMed

    Fewtrell, Mary S; Edmonds, Caroline J; Isaacs, Elizabeth; Bishop, Nick J; Lucas, Alan

    2011-08-01

    Aluminium is the most common metallic element, but has no known biological role. It accumulates in the body when protective gastrointestinal mechanisms are bypassed, renal function is impaired, or exposure is high - all of which apply frequently to preterm infants. Recognised clinical manifestations of aluminium toxicity include dementia, anaemia and bone disease. Parenteral nutrition (PN) solutions are liable to contamination with aluminium, particularly from acidic solutions in glass vials, notably calcium gluconate. When fed parenterally, infants retain >75% of the aluminium, with high serum, urine and tissue levels. Later health effects of neonatal intravenous aluminium exposure were investigated in a randomised trial comparing standard PN solutions with solutions specially sourced for low aluminium content. Preterm infants exposed for >10 d to standard solutions had impaired neurologic development at 18 months. At 13-15 years, subjects randomised to standard PN had lower lumbar spine bone mass; and, in non-randomised analyses, those with neonatal aluminium intake above the median had lower hip bone mass. Given the sizeable number of infants undergoing intensive care and still exposed to aluminium via PN, these findings have contemporary relevance. Until recently, little progress had been made on reducing aluminium exposure, and meeting Food and Drug Administration recommendations (<5 μg/kg per d) has been impossible in patients <50 kg using available products. Recent advice from the UK Medicines and Healthcare regulatory Authority that calcium gluconate in small volume glass containers should not be used for repeated treatment in children <18 years, including preparation of PN, is an important step towards addressing this problem.

  5. SUPERCONDUCTING VANADIUM BASE ALLOY

    DOEpatents

    Cleary, H.J.

    1958-10-21

    A new vanadium-base alloy which possesses remarkable superconducting properties is presented. The alloy consists of approximately one atomic percent of palladium, the balance being vanadium. The alloy is stated to be useful in a cryotron in digital computer circuits.

  6. Weldability of intermetallic alloys

    SciTech Connect

    David, S.A. )

    1990-01-01

    Ordered intermetallic alloys are a unique class of material that have potential for structural applications at elevated temperatures. The paper describes the welding and weldability of these alloys. The alloys studied were nickel aluminide (Ni[sub 3]Al), titanium aluminide (Ti[sub 3]Al), and iron aluminide.

  7. DELTA PHASE PLUTONIUM ALLOYS

    DOEpatents

    Cramer, E.M.; Ellinger, F.H.; Land. C.C.

    1960-03-22

    Delta-phase plutonium alloys were developed suitable for use as reactor fuels. The alloys consist of from 1 to 4 at.% zinc and the balance plutonium. The alloys have good neutronic, corrosion, and fabrication characteristics snd possess good dimensional characteristics throughout an operating temperature range from 300 to 490 deg C.

  8. PLUTONIUM-THORIUM ALLOYS

    DOEpatents

    Schonfeld, F.W.

    1959-09-15

    New plutonium-base binary alloys useful as liquid reactor fuel are described. The alloys consist of 50 to 98 at.% thorium with the remainder plutonium. The stated advantages of these alloys over unalloyed plutonium for reactor fuel use are easy fabrication, phase stability, and the accompanying advantuge of providing a means for converting Th/sup 232/ into U/sup 233/.

  9. Separation in Binary Alloys

    NASA Technical Reports Server (NTRS)

    Frazier, D. O.; Facemire, B. R.; Kaukler, W. F.; Witherow, W. K.; Fanning, U.

    1986-01-01

    Studies of monotectic alloys and alloy analogs reviewed. Report surveys research on liquid/liquid and solid/liquid separation in binary monotectic alloys. Emphasizes separation processes in low gravity, such as in outer space or in free fall in drop towers. Advances in methods of controlling separation in experiments highlighted.

  10. The aluminium content of breast tissue taken from women with breast cancer.

    PubMed

    House, Emily; Polwart, Anthony; Darbre, Philippa; Barr, Lester; Metaxas, George; Exley, Christopher

    2013-10-01

    The aetiology of breast cancer is multifactorial. While there are known genetic predispositions to the disease it is probable that environmental factors are also involved. Recent research has demonstrated a regionally specific distribution of aluminium in breast tissue mastectomies while other work has suggested mechanisms whereby breast tissue aluminium might contribute towards the aetiology of breast cancer. We have looked to develop microwave digestion combined with a new form of graphite furnace atomic absorption spectrometry as a precise, accurate and reproducible method for the measurement of aluminium in breast tissue biopsies. We have used this method to test the thesis that there is a regional distribution of aluminium across the breast in women with breast cancer. Microwave digestion of whole breast tissue samples resulted in clear homogenous digests perfectly suitable for the determination of aluminium by graphite furnace atomic absorption spectrometry. The instrument detection limit for the method was 0.48 μg/L. Method blanks were used to estimate background levels of contamination of 14.80 μg/L. The mean concentration of aluminium across all tissues was 0.39 μg Al/g tissue dry wt. There were no statistically significant regionally specific differences in the content of aluminium. We have developed a robust method for the precise and accurate measurement of aluminium in human breast tissue. There are very few such data currently available in the scientific literature and they will add substantially to our understanding of any putative role of aluminium in breast cancer. While we did not observe any statistically significant differences in aluminium content across the breast it has to be emphasised that herein we measured whole breast tissue and not defatted tissue where such a distribution was previously noted. We are very confident that the method developed herein could now be used to provide accurate and reproducible data on the aluminium content

  11. Cobalt and Nickel Nanopillars on Aluminium Substrates by Direct Current Electrodeposition Process

    PubMed Central

    2009-01-01

    A fast and cost-effective technique is applied for fabricating cobalt and nickel nanopillars on aluminium substrates. By applying an electrochemical process, the aluminium oxide barrier layer is removed from the pore bottom tips of nanoporous anodic alumina templates. So, cobalt and nickel nanopillars are fabricated into these templates by DC electrodeposition. The resulting nanostructure remains on the aluminium substrate. In this way, this method could be used to fabricate a wide range of nanostructures which could be integrated in new nanodevices. PMID:20596338

  12. Rhenium alloying of tungsten heavy alloys

    SciTech Connect

    German, R.M.; Bose, A.; Jerman, G.

    1989-01-01

    Alloying experiments were performed using rhenium additions to a classic 90 mass % tungsten heavy alloy. The mixed-powder system was liquid phase sintered to full density at 1500 C in 60 min The rhenium-modified alloys exhibited a smaller grain size, higher hardness, higher strength, and lower ductility than the unalloyed system. For an alloy with a composition of 84W-6Re-8Ni-2Fe, the sintered density was 17, 4 Mg/m{sup 3} with a yield strength of 815 MPa, tensile strength of 1180 MPa, and elongation to failure of 13%. This property combination results from the aggregate effects of grain size reduction and solid solution hardening due to rhenium. In the unalloyed system these properties require post-sintering swaging and aging; thus, alloying with rhenium is most attractive for applications where net shaping is desired, such as by powder injection molding.

  13. Processing and alloying of tungsten heavy alloys

    SciTech Connect

    Bose, A.; Dowding, R.J.

    1993-12-31

    Tungsten heavy alloys are two-phase metal matrix composites with a unique combination of density, strength, and ductility. They are processed by liquid-phase sintering of mixed elemental powders. The final microstructure consists of a contiguous network of nearly pure tungsten grains embedded in a matrix of a ductile W-Ni-Fe alloy. Due to the unique property combination of the material, they are used extensively as kinetic energy penetrators, radiation shields. counterbalances, and a number of other applications in the defense industry. The properties of these alloys are extremely sensitive to the processing conditions. Porosity levels as low as 1% can drastically degrade the properties of these alloys. During processing, care must be taken to reduce or prevent incomplete densification, hydrogen embrittlement, impurity segregation to the grain boundaries, solidification shrinkage induced porosity, and in situ formation of pores due to the sintering atmosphere. This paper will discuss some of the key processing issues for obtaining tungsten heavy alloys with good properties. High strength tungsten heavy alloys are usually fabricated by swaging and aging the conventional as-sintered material. The influence of this on the shear localization tendency of a W-Ni-Co alloy will also be demonstrated. Recent developments have shown that the addition of certain refractory metals partially replacing tungsten can significantly improve the strength of the conventional heavy alloys. This development becomes significant due to the recent interest in near net shaping techniques such as powder injection moldings. The role of suitable alloying additions to the classic W-Ni-Fe based heavy alloys and their processing techniques will also be discussed in this paper.

  14. High strength alloys

    DOEpatents

    Maziasz, Phillip James [Oak Ridge, TN; Shingledecker, John Paul [Knoxville, TN; Santella, Michael Leonard [Knoxville, TN; Schneibel, Joachim Hugo [Knoxville, TN; Sikka, Vinod Kumar [Oak Ridge, TN; Vinegar, Harold J [Bellaire, TX; John, Randy Carl [Houston, TX; Kim, Dong Sub [Sugar Land, TX

    2010-08-31

    High strength metal alloys are described herein. At least one composition of a metal alloy includes chromium, nickel, copper, manganese, silicon, niobium, tungsten and iron. System, methods, and heaters that include the high strength metal alloys are described herein. At least one heater system may include a canister at least partially made from material containing at least one of the metal alloys. At least one system for heating a subterranean formation may include a tubular that is at least partially made from a material containing at least one of the metal alloys.

  15. High strength alloys

    DOEpatents

    Maziasz, Phillip James; Shingledecker, John Paul; Santella, Michael Leonard; Schneibel, Joachim Hugo; Sikka, Vinod Kumar; Vinegar, Harold J.; John, Randy Carl; Kim, Dong Sub

    2012-06-05

    High strength metal alloys are described herein. At least one composition of a metal alloy includes chromium, nickel, copper, manganese, silicon, niobium, tungsten and iron. System, methods, and heaters that include the high strength metal alloys are described herein. At least one heater system may include a canister at least partially made from material containing at least one of the metal alloys. At least one system for heating a subterranean formation may include a tublar that is at least partially made from a material containing at least one of the metal alloys.

  16. Synthesis and characterization of luminescent aluminium selenide nanocrystals

    SciTech Connect

    Balitskii, O.A.; Demchenko, P.Yu.; Mijowska, E.; Cendrowski, K.

    2013-02-15

    Highlights: ► Synthesis procedure of size and sharp controlled Al{sub 2}Se{sub 3} nanocrystals is introduced. ► Obtained nanoparticles are highly crystalline of hexagonal wurtzite type. ► Colloidal Al{sub 2}Se{sub 3} nanocrystals are highly luminescent in the near UV spectral region. ► They can be implemented in light emitters/collectors, concurring with II–VI nanodots. -- Abstract: We propose the synthesis and characterization of colloidal aluminium selenide nanocrystals using trioctylphosphine as a solvent. The nanoparticles have several absorption bands in the spectral region 330–410 nm and are bright UV-blue luminescent, which is well demanded in light collecting and emitting devices, e.g. for tuning their spectral characteristics to higher energy solar photons.

  17. Neutron irradiation influence on magnesium aluminium spinel inversion

    NASA Astrophysics Data System (ADS)

    Skvortsova, V.; Mironova-Ulmane, N.; Ulmanis, U.

    2002-05-01

    Grown by the Verneuil method MgO · nAl 2O 3 single crystals and natural spinel crystal have been studied using X-ray diffraction and photoluminescence spectra. The fast neutron irradiation of magnesium aluminium spinel leads to the lattice parameter decrease. The bond lengths of Mg-O and Al-O vary with the u-parameter and the lattice parameter. On the other hand, the bond lengths are related with the inversion parameter. Using changes of the lattice parameter during irradiation we have calculated the inversion parameter, which is 15-20%. In the luminescence spectra, the fast neutron radiation (fluence 10 16 cm -2) produces an increase in the intensity ratio of the N- to R-lines by 5-20%. Taking into account that intensity of the N-lines is closely associated with the inversion parameter, it is possible to state that the neutron irradiation causes the increasing of the spinel inversion.

  18. Natural gas anodes for aluminium electrolysis in molten fluorides.

    PubMed

    Haarberg, Geir Martin; Khalaghi, Babak; Mokkelbost, Tommy

    2016-08-15

    Industrial primary production of aluminium has been developed and improved over more than 100 years. The molten salt electrolysis process is still suffering from low energy efficiency and considerable emissions of greenhouse gases (CO2 and PFC). A new concept has been suggested where methane is supplied through the anode so that the CO2 emissions may be reduced significantly, the PFC emissions may be eliminated and the energy consumption may decrease significantly. Porous carbon anodes made from different graphite grades were studied in controlled laboratory experiments. The anode potential, the anode carbon consumption and the level of HF gas above the electrolyte were measured during electrolysis. In some cases it was found that the methane oxidation was effectively participating in the anode process.

  19. Multicomponental fluorimetric determination of aluminium, gallium and indium.

    PubMed

    Vojta, Simon; Jancár, Ludek; Sommer, Lumír

    2008-03-01

    For the fast characteristics of mixtures of Aluminium, Gallium and Indium the fluorimetric evaluation in the form of complexes with 8-Hydroxyquinoline-5-sulphonic acid is described at selected pH. The highly collinear correlated fluorescent spectra and their first derivation were evaluated under various experimental conditions with the Multiple Linear Regression (MLR), Partial Least Squares (PLS) methods and Kalman filtering. When comparing the results, the PLS gives the least relative prediction errors under optimal conditions, 5.6-15.9% for the concentration range of Al 0.025-0.2 microg cm(-3), Ga 0.1-0.8 microgcm(-3) and In 0.1-0.8 microg cm(-3) in the mixture.

  20. Quasiparticle spin resonance and coherence in superconducting aluminium

    NASA Astrophysics Data System (ADS)

    Quay, C. H. L.; Weideneder, M.; Chiffaudel, Y.; Strunk, C.; Aprili, M.

    2015-10-01

    Conventional superconductors were long thought to be spin inert; however, there is now increasing interest in both (the manipulation of) the internal spin structure of the ground-state condensate, as well as recently observed long-lived, spin-polarized excitations (quasiparticles). We demonstrate spin resonance in the quasiparticle population of a mesoscopic superconductor (aluminium) using novel on-chip microwave detection techniques. The spin decoherence time obtained (~100 ps), and its dependence on the sample thickness are consistent with Elliott-Yafet spin-orbit scattering as the main decoherence mechanism. The striking divergence between the spin coherence time and the previously measured spin imbalance relaxation time (~10 ns) suggests that the latter is limited instead by inelastic processes. This work stakes out new ground for the nascent field of spin-based electronics with superconductors or superconducting spintronics.

  1. Multiple nanostructures based on anodized aluminium oxide templates

    NASA Astrophysics Data System (ADS)

    Wen, Liaoyong; Xu, Rui; Mi, Yan; Lei, Yong

    2016-11-01

    Several physico-chemical effects and properties in the solid state involve nanoscale interactions between adjacent materials and morphologies. Arrays of binary nanostructures can generate intimate interactions between different sub-components, but fabricating binary nanostructures is challenging. Here, we propose a concept to achieve diverse binary nanostructure arrays with high degrees of controllability for each of the sub-components, including material, dimension and morphology. This binary nanostructuring concept originates with a distinctive binary-pore anodized aluminium oxide template that includes two dissimilar sets of pores in one matrix, where the openings of the two sets of pores are towards opposite sides of the template. Using the same growth mechanism, the binary-pore template can be extended to multi-pore templates with more geometrical options. We also present photoelectrodes, transistors and plasmonic devices made with our binary nanostructure arrays using different combination of materials and morphologies, and demonstrate superior performances compared to their single-component counterparts.

  2. Benchmark 2 - Springback of a Jaguar Land Rover Aluminium

    NASA Astrophysics Data System (ADS)

    Allen, Martin; Oliveira, Marta; Hazra, Sumit; Adetoro, Oluwamayokun; Das, Abhishek; Cardoso, Rui

    2016-08-01

    The aim of this benchmark is the numerical prediction of the springback of an aluminium panel used in the production of a Jaguar car. The numerical simulation of springback has been very important for the reduction of die try outs through the design of the tools with die compensation, thereby allowing for the production of dimensionally accurate complex parts at a reduced cost. The forming stage of this benchmark includes one single forming operation followed by a trimming operation. Cross-sectional profiles should be reported at specific (provided) sections in the part before and after springback. Problem description, tool geometries, material properties, and the required simulation reports are summarized in this benchmark briefing.

  3. Microstructure characterization of hypereutectoid aluminium bronze composite coating

    NASA Astrophysics Data System (ADS)

    Kucita, P.; Wang, S. C.; Li, W. S.; Cook, R. B.; Starink, M. J.

    2015-10-01

    Hypereutectoid aluminium bronze coating was deposited onto an E.N. 10503 steel substrate using plasma transferred arc welding (PTA). Microstructure characterisation of the coating and a section near the steel substrate joint was carried out using SEM, EBSD, EDS in conjunction with XRD and depth-sensing nano-indentation. The constituent phases in the coating were identified as: martensitic Cu3Al β1' phase, solid solution of Al in Cu α phase and the intermetallic Fe3Al κ1 phase. The region near the steel substrate was characterised by high hardness, large grains and presence of Cu precipitates. No cracks were observed in this region. The coating has high hardness of 4.9GPa and Young's modulus of 121.7GPa. This is attributed to homogeneous distribution of sub microns size Fe3Al intermetallic phase. The implications of the coating to the engineering application of sheet metal forming are discussed.

  4. Unusual sources of aluminium and heavy metals in potable waters.

    PubMed

    Fuge, R; Pearce, N J; Perkins, W T

    1992-04-01

    Aluminium in water supplies derives from natural sources and from the use of Al2(SO4)3 in water treatment. Heavy metals such as Pb, Cu, Zn and Cd can be added to water from pipework and solder. However, it is apparent that AI and other metals in potable waters can derive from deposits on pipe walls which can be subsequently mobilised when the supply and/or treatment process is changed. Concentrations of Al in domestic supply water of the Llanbrynmair area have been shown to increase from 1 μg to 50 μg L(-1) during its 18 km journey along the water main. Similarly, Pb concentrations in a public building in the Aberystwyth area are found to be extremely elevated due to the metal's mobilisation from encrustations occurring on the copper pipework.

  5. Creep Resistant Zinc Alloy

    SciTech Connect

    Frank E. Goodwin

    2002-12-31

    This report covers the development of Hot Chamber Die Castable Zinc Alloys with High Creep Strengths. This project commenced in 2000, with the primary objective of developing a hot chamber zinc die-casting alloy, capable of satisfactory service at 140 C. The core objectives of the development program were to: (1) fill in missing alloy data areas and develop a more complete empirical model of the influence of alloy composition on creep strength and other selected properties, and (2) based on the results from this model, examine promising alloy composition areas, for further development and for meeting the property combination targets, with the view to designing an optimized alloy composition. The target properties identified by ILZRO for an improved creep resistant zinc die-casting alloy were identified as follows: (1) temperature capability of 1470 C; (2) creep stress of 31 MPa (4500 psi); (3) exposure time of 1000 hours; and (4) maximum creep elongation under these conditions of 1%. The project was broadly divided into three tasks: (1) Task 1--General and Modeling, covering Experimental design of a first batch of alloys, alloy preparation and characterization. (2) Task 2--Refinement and Optimization, covering Experimental design of a second batch of alloys. (3) Task 3--Creep Testing and Technology transfer, covering the finalization of testing and the transfer of technology to the Zinc industry should have at least one improved alloy result from this work.

  6. Evaluation of shear bond strength of composite resin bonded to alloy treated with sandblasting and electrolytic etching.

    PubMed

    Goswami, M M; Gupta, S H; Sandhu, H S

    2014-03-01

    Conservation of natural tooth structure precipitated the emergence of resin-retained fixed partial dentures. The weakest link in this modality is the bond between resin cement and alloy of the retainer. Various alloy surface treatment have been recommended to improve alloy-resin bond. This in vitro study was carried out to observe changes in the Nickel-Chromium alloy (Wiron 99, Bego) surface following sandblasting or electrolytic etching treatment by scanning electron microscope (SEM) and to evaluate the shear bond strength of a resin luting cement bonded to the surface treated alloy. 80 alloy blocks were cast and divided into four groups of 20 each. In groups-A & B, the test surfaces were treated by sandblasting with 50 and 250 μm sized aluminium oxide particles respectively. In groups-C & D, the test surfaces were first treated by sandblasting with 50 and 250 μm sized aluminium oxide particles respectively followed by electrolytic etching. Test surfaces were observed under SEM at 1,000× magnification. Two alloy blocks of each group were luted together by a resin luting cement (Rely X, 3M) and their shear bond strength was tested. The mean shear bond strength in MPa of groups-A to D were 6.44 (±0.74), 8.18 (±0.51), 14.45 (±0.59) and 17.43 (±1.20) respectively. Group-D showed bond strength that is more than clinically acceptable bond strength. It is recommended that before luting resin-retained fixed partial dentures, the fitting surface of the retainer should be electrolytically etched to achieve adequate micromechanical retention.

  7. Cyclic carbonate synthesis catalysed by bimetallic aluminium-salen complexes.

    PubMed

    Clegg, William; Harrington, Ross W; North, Michael; Pasquale, Riccardo

    2010-06-18

    The development of bimetallic aluminium-salen complexes [{Al(salen)}(2)O] as catalysts for the synthesis of cyclic carbonates (including the commercially important ethylene and propylene carbonates) from a wide range of terminal epoxides in the presence of tetrabutylammonium bromide as a cocatalyst is reported. The bimetallic structure of one complex was confirmed by X-ray crystallography. The bimetallic complexes displayed exceptionally high catalytic activity and in the presence of tetrabutylammonium bromide could catalyse cyclic carbonate synthesis at atmospheric pressure and room temperature. Catalyst-reuse experiments demonstrated that one bimetallic complex was stable for over 60 reactions, though the tetrabutylammonium bromide decomposed in situ by a retro-Menschutkin reaction to form tributylamine and had to be regularly replaced. The mild reaction conditions allowed a full analysis of the reaction kinetics to be carried out and this showed that the reaction was first order in aluminium complex concentration, first order in epoxide concentration, first order in carbon dioxide concentration (except when used in excess) and unexpectedly second order in tetrabutylammonium bromide concentration. Further kinetic experiments demonstrated that the tributylamine formed in situ was involved in the catalysis and that addition of butyl bromide to reconvert the tributylamine into tetrabutylammonium bromide resulted in inhibition of the reaction. The reaction kinetics also indicated that no kinetic resolution of racemic epoxides was possible with this class of catalysts, even when the catalyst was derived from a chiral salen ligand. However, it was shown that if enantiomerically pure styrene oxide was used as substrate, then enantiomerically pure styrene carbonate was formed. On the basis of the kinetic and other experimental data, a catalytic cycle that explains why the bimetallic complexes display such high catalytic activity has been developed.

  8. The effect of metallic oxide deposition on the electrochemical behaviour of Al-Zn-Mg-Sn alloy in natural tropical seawater

    NASA Astrophysics Data System (ADS)

    Din Yati, M. S.; Nazree Derman, Mohd; Isa, M. C.; Y Ahmad, M.; Yusoff, N. H. N.; Muhammad, M. M.; Nain, H.

    2014-06-01

    The potential of aluminium alloys as anode materials in cathodic protection system has been explored and a significant improvement has been achieved. However, for marine application, it is quite difficult to maintain continuous activation process due to passivation behavior of aluminum alloys. Therefore, to choose the best activation mechanism for aluminium alloy in marine environment, it has to be considered from various points such as alloy composition and surface treatment. This paper report the effect of metallic ruthenium oxide (RuO2) deposition on the surface of as-cast Al-Zn-Mg-Sn alloy and to study the effect of its presence on the electrochemical behavior using direct current (DC) electrochemical polarization and current capacity measurement. The morphology and topography of corroded surface were studied by the aid of scanning electron microscope (SEM) and confocal laser scanning microscope (CLSM) respectively. Results from this study showed that the presence of intermetallic compound (Mg2Sn) and also mixed metal oxide compound (Al2O3 and RuO2) on the alloy surface has been very useful in improving electrochemical reaction and charge transfer activities in chloride containing solution. This study also showed that RuO2 catalytic coating applied on the surface of Al-Zn-Mg-Sn alloy has slightly increased the corrosion current density compared to Al-Zn-Mg-Sn without RuO2. The corrosion morphology and topography of corroded surface of Al-Zn-Mg-Sn alloy deposited with RuO2 was found more uniform corrosion attack with the formation of porous and fibrous mud-like crack on outer layer. Based on surface morphology and 3D topographic studies, these features were believed to facilitate ionic species adsorption and diffusion through corrosion product layer at solution-alloy interface. Deposited RuO2 films also was found to increase of current efficiency by more than 10%.

  9. Gamma titanium aluminide alloys

    SciTech Connect

    Yamaguchi, M.; Inui, H.; Kishida, K.; Matsumuro, M.; Shirai, Y.

    1995-08-01

    Extensive progress and improvements have been made in the science and technology of gamma titanium aluminide alloys within the last decade. In particular, the understanding of their microstructural characteristics and property/microstructure relationships has been substantially deepened. Based on these achievements, various engineering two-phase gamma alloys have been developed and their mechanical and chemical properties have been assessed. Aircraft and automotive industries arc pursuing their introduction for various structural components. At the same time, recent basic studies on the mechanical properties of two-phase gamma alloys, in particular with a controlled lamellar structure have provided a considerable amount of fundamental information on the deformation and fracture mechanisms of the two-phase gamma alloys. The results of such basic studies are incorporated in the recent alloy and microstructure design of two-phase gamma alloys. In this paper, such recent advances in the research and development of the two-phase gamma alloys and industrial involvement are summarized.

  10. Non-aqueous aluminium-air battery based on ionic liquid electrolyte

    NASA Astrophysics Data System (ADS)

    Revel, Renaud; Audichon, Thomas; Gonzalez, Serge

    2014-12-01

    A promising metal-air secondary battery based on aluminium-oxygen couple is described. In this paper, we observed that an aluminium-air battery employing EMImCl, AlCl3 room temperature ionic liquid (RTIL) as electrolyte and aluminium as negative electrode, has an exceptional reduced self-discharged rate. Due to its new and innovative type of electrolyte, this aluminium-air battery can support relatively high current densities (up to 0.6 mA cm-2) and an average voltage of 0.6-0.8 V. Such batteries may find immediate applications, as they can provide an internal, built-in autonomous and self-sustained energy source.

  11. Numerical modelling of closed-cell aluminium foam under dynamic loading

    NASA Astrophysics Data System (ADS)

    Hazell, Paul; Kader, M. A.; Islam, M. A.; Escobedo, J. P.; Saadatfar, M.

    2015-06-01

    Closed-cell aluminium foams are extensively used in aerospace and automobile industries. The understanding of their behaviour under impact loading conditions is extremely important since impact problems are directly related to design of these engineering structures. This research investigates the response of a closed-cell aluminium foam (CYMAT) subjected to dynamic loading using the finite element software ABAQUS/explicit. The aim of this research is to numerically investigate the material and structural properties of closed-cell aluminium foam under impact loading conditions with interest in shock propagation and its effects on cell wall deformation. A μ-CT based 3D foam geometry is developed to simulate the local cell collapse behaviours. A number of numerical techniques are applied for modelling the crush behaviour of aluminium foam to obtain the more accurate results. The simulation results are compared with experimental data. Comparison of the results shows a good correlation between the experimental results and numerical predictions.

  12. Shear Strength of Single Lap Joint Aluminium-Thermoplastic Natural Rubber (Al-TPNR) Laminated Composite

    NASA Astrophysics Data System (ADS)

    Muzakkar, M. Z.; Ahmad, S.; Yarmo, M. A.; Jalar, A.; Bijarimi, M.

    2013-04-01

    In this work, we studied the effect of surface treatment on the aluminium surface and a coupling agent to improve adhesion between aluminium with organic polymer. Thermoplastic natural rubber (TPNR) matrix was prepared by melt blending of natural rubber (NR), liquid natural rubber (LNR) compatibilizer, linear low density polyethylene (LLDPE) and polyethylene grafted maleic anhydride (PE-g-MAH). The PEgMAH concentration used was varied from 0% - 25%. In addition, the aluminium surface was pre-treated with 3-glycidoxy propyl trimethoxy silane (3-GPS) to enhance the mechanical properties of laminated composite. It was found that the shear strength of single lap joint Al-TPNR laminated composite showing an increasing trend as a function of PE-g-MAH contents for the 3-GPS surface treated aluminium. Moreover, the scanning electron microscope (SEM) revealed that the strength improvement was associated with the chemical state of the compound involved.

  13. Determination of soluble aluminium concentration in alkaline humic water using atomic absorption spectrophotometry.

    PubMed

    Nguyen, K L; Lewis, D M; Jolly, M; Robinson, J

    2004-11-01

    The steps of the standard method to determine soluble aluminium concentration are filtering, followed by acidifying, then analysing with the atomic absorption spectrophotometer (AAS). When applied to alkaline humic water, acidification gives rise to the formation of humic acid as a brown particulate matter. Of the total soluble aluminium in the original water, 49-61% forms complexes with the particulate humic acid upon acidification. Although the AAS is capable of detecting the binding aluminium, the particulate nature of humic acid easily induces inaccurate readings as a result of the non-uniform distribution of the particulate matter. A more precise analysis of soluble aluminium concentration of alkaline humic water is shown to be achievable in basicified solutions instead. Basicified solutions keep humic acid in the soluble form; hence maintain the homogeneity of the sample.

  14. Weldability of High Alloys

    SciTech Connect

    Maroef, I

    2003-01-22

    The purpose of this study was to investigate the effect of silicon and iron on the weldability of HAYNES HR-160{reg_sign} alloy. HR-I60 alloy is a solid solution strengthened Ni-Co-Cr-Si alloy. The alloy is designed to resist corrosion in sulfidizing and other aggressive high temperature environments. Silicon is added ({approx}2.75%) to promote the formation of a protective oxide scale in environments with low oxygen activity. HR-160 alloy has found applications in waste incinerators, calciners, pulp and paper recovery boilers, coal gasification systems, and fluidized bed combustion systems. HR-160 alloy has been successfully used in a wide range of welded applications. However, the alloy can be susceptible to solidification cracking under conditions of severe restraint. A previous study by DuPont, et al. [1] showed that silicon promoted solidification cracking in the commercial alloy. In earlier work conducted at Haynes, and also from published work by DuPont et al., it was recognized that silicon segregates to the terminal liquid, creating low melting point liquid films on solidification grain boundaries. Solidification cracking has been encountered when using the alloy as a weld overlay on steel, and when joining HR-160 plate in a thickness greater than19 millimeters (0.75 inches) with matching filler metal. The effect of silicon on the weldability of HR-160 alloy has been well documented, but the effect of iron is not well understood. Prior experience at Haynes has indicated that iron may be detrimental to the solidification cracking resistance of the alloy. Iron does not segregate to the terminal solidification product in nickel-base alloys, as does silicon [2], but iron may have an indirect or interactive influence on weldability. A set of alloys covering a range of silicon and iron contents was prepared and characterized to better understand the welding metallurgy of HR-160 alloy.

  15. Dynamic crushing response of closed-cell aluminium foams during shock loading

    NASA Astrophysics Data System (ADS)

    Islam, M. A.; Kader, M. A.; Hazell, P. J.; Escobedo-Diaz, J. P.; Brown, A. D.; Appleby-Thomas, G. J.; Saadatfar, M.; Quadir, M. Z.

    2017-01-01

    Understanding the impact response of aluminium foams is essential for assessing their energy absorption capacity under dynamic loading. In this paper, the dynamic compaction behavior of closed-cell aluminium foam (CYMAT ™) has been tested using the plate-impact technique. Post-impacted samples have been examined using optical microscopy to observe the microstructural changes with the objective of elucidating the pore-collapse mechanism.

  16. Stress proteins and glial cell functions during chronic aluminium exposures: protective role of curcumin.

    PubMed

    Sood, Pooja Khanna; Nahar, Uma; Nehru, Bimla

    2012-03-01

    Involved in the ongoing debate is the speculation that aluminium is somehow toxic for neurons. Glial cells cope up to protect neurons from this toxic insult by maintaining the glutathione homeostasis. Of late newer and newer roles of glial cells have been depicted. The present work looks into the other regulatory mechanisms that show the glial cells response to pro-oxidant effects of aluminium exposure. In the present investigation we have evaluated the inflammatory responses of the glial cells as well as HSP70-induction during aluminium exposure. Further, the protective role of curcumin is also evaluated. Aluminium was administered by oral gavage at a dose level of 100 mg/kg b.wt/day for a period of 8 weeks. Curcumin was administered i.p. at a dose of 50 mg/kg b.wt./day on alternate days. Enhanced gene and protein expression of HSP70 in the glial fractions of the aluminium exposed animals as compared to the corresponding neuronal population. Aluminium exposure resulted in a significant increase in the NF-κB and TNF-α expression suggesting inflammatory responses. In the conjunctive treatment group of aluminium and curcumin exposure marked reduction in the gene and protein expression of NF-κB and TNF-α was observed. This was further reflected in histopathological studies showing no evidence of inflammation in conjunctive group as compared to aluminium treatment. From the present study, it can be concluded that curcumin has a potential anti-inflammatory action and can be exploited in other toxicological conditions also.

  17. Aluminium hydroxide tetra-3-phenylthiophthalocyanine as new photosensitizer for photodynamic therapy and fluorescent diagnostics

    NASA Astrophysics Data System (ADS)

    Meerovich, I. G.; Smirnova, Z. S.; Oborotova, N. A.; Lukyanets, E. A.; Meerovich, G. A.; Derkacheva, V. M.; Polozkova, A. P.; Kubasova, I. Y.; Baryshnikov, A. Y.

    2005-08-01

    This work is devoted to investigation of possibility to use the liposomal form of aluminium hydroxide tetra-3-phenylthiophthalocyanine as photosensitizer of near-infrared range. Aluminium hydroxide tetra-3-phenylthiophthalocyanine has shown high selectivity of accumulation in tumor comparing to normal tissue of mice as well as high photodynamic efficiency on mice bearing Erlich tumor (ELD) and lympholeucosis P-388. This compozition can be used to develop new effective photosensitizer for photodynamic therapy and fluorescent diagnostics.

  18. Evaluating Primary Dendrite Trunk Diameters in Directionally Solidified Al-Si Alloys

    NASA Technical Reports Server (NTRS)

    Grugel, R. N.; Tewari, S. N.; Poirier, D. R.

    2014-01-01

    The primary dendrite trunk diameters of Al-Si alloys that were directionally solidified over a range of processing conditions have been measured. These data are analyzed with a model based primarily on an assessment of secondary dendrite arm dissolution in the mushy zone. Good fit with the experimental data is seen and it is suggested that the primary dendrite trunk diameter is a useful metric that correlates well with the actual solidification processing parameters. These results are placed in context with the limited results from the aluminium - 7 wt. % silicon samples directionally solidified aboard the International Space Station as part of the MICAST project.

  19. Small Crack Growth and Its Influence in Near Alpha-Titanium Alloys

    DTIC Science & Technology

    1989-06-01

    M.N. James An Assessment of Crack Closure and the Extent of the J.F. Knott Short Crack Regime in QIN ( HY80 ) Steel . Fatigue Fract Engng Mater Struct, 8...Effects in A508 F. Mudry Steel . A. Pinneau Fatigue of Engineering Materials and Structures, 6, pp 349-358 (1983) 3 B.N. Leis Discussion of the Short...Crack Growth in Steels and A.J. McEvily Aluminium Alloys. In: Proceedings of the Int Conf on Fatigue Thresholds, Stockholm, Sweden, 2, pp 36 (1981) 21

  20. Alloy 10: A 1300F Disk Alloy

    NASA Technical Reports Server (NTRS)

    Gayda, John

    2000-01-01

    Gas turbine engines for future subsonic transports will probably have higher pressure ratios which will require nickel-base superalloy disks with 13000 to 1400 F temperature capability. Several advanced disk alloys are being developed to fill this need. One of these, Allied Signal's Alloy 10, is a promising candidate for gas turbine engines to be used on smaller, regional aircraft. For this application, compressor/turbine disks must withstand temperatures of 1300 F for several hundred hours over the life of the engine. In this paper, three key properties of Alloy 10--tensile, 0.2% creep, and fatigue crack growth--will be assessed at 1300 F.

  1. Naturally occurring radioactive material from the aluminium industry--a case study: the Egyptian Aluminium Company, Nag Hammady, Egypt.

    PubMed

    Abbady, Adel G E; El-Arabi, A M

    2006-12-01

    The activity concentrations and the gamma-absorbed dose rates of the terrestrial naturally occurring radionuclides (226)Ra and (232)Th were determined in samples of bauxite, alumina and aluminium dross tailings industrial waste (used to produce two types of alums) using high purity germanium (HPGe) gamma ray spectrometry. The bauxite and alumina are imported by Egyptalum (The Egyptian Aluminium Company, Nag Hammady, Egypt) from Guinea and India. The activity concentrations in the bauxite range from 29 +/- 1 to 112 +/- 6 Bq kg(-1) for (226)Ra, and 151 +/- 8 to 525 +/- 12 Bq kg(-1) for (232)Th, with mean values of 62 +/- 8 and 378 +/- 50 Bq kg(-1), respectively. With respect to alumina and tail, the mean values are 5.7 +/- 1.1 and 8.4 +/- 0.8 Bq kg(-1) for (226)Ra and 7.2 +/- 1.6 and 10.7 +/- 1.2 Bq kg(-1) for (232)Th. Potassium-40 was not detected in any of the studied samples. The measured activity concentrations of (226)Ra and (232)Th in bauxite are higher than the world average while in alumina and tail they are lower. As a measure of radiation hazard to the occupational workers and members of the public, the Ra equivalent activities and external gamma dose rates due to natural radionuclides at 1 m above the ground surface were calculated. The external gamma-radiation doses received by the Egyptalum workers are 97, 409, 8.5 and 12.7 microSv y(-1) for the Guinean and Indian bauxite, the alumina and tail, respectively, which is well below the recommended allowed dose of 1 mSv y(-1) for non-exposed workers.

  2. Studies on adhesion characteristics and corrosion behaviour of vinyltriethoxysilane/epoxy coating protective system on aluminium

    NASA Astrophysics Data System (ADS)

    Bajat, Jelena B.; Milošev, Ingrid; Jovanović, Željka; Mišković-Stanković, Vesna B.

    2010-03-01

    The corrosion stability of vinyltriethoxysilane/epoxy coating protective system on aluminium is strongly related to the strength of bonds forming at the metal/organic coating interface. This article is a study of adhesion, composition, electrochemical and transport properties of epoxy coatings electrodeposited on bare aluminium and aluminium pretreated by vinyltriethoxysilane (VTES) during exposure to 3% NaCl. The VTES film was deposited on aluminium surface from 2% vinyltriethoxysilane solution during 30 s. From the values of adhesion strength (pull-off test), time dependence of pore resistance and coating capacitance of epoxy coating (impedance measurements) and diffusion coefficient of water through epoxy coating (gravimetric liquid sorption measurements), the influence of VTES sublayer on the corrosion stability of the electrodeposited epoxy coating was shown. The work discusses the role of the VTES pretreatment in the enhanced adhesion and corrosion stability of epoxy cataphoretic coating. The electrochemical results showed that the aluminium pretreatment by VTES film improved barrier properties of epoxy coating (greater pore resistance and lower coating capacitance). The lower value of diffusion coefficient of water through epoxy coating indicates the lower porosity, while the smaller adhesion reduction points to better adhesion of epoxy coating on aluminium pretreated by VTES film. The composition of the deposited coatings investigated by XPS enabled the clarification of the bonding mechanism.

  3. Oxidation and waste-to-energy output of aluminium waste packaging during incineration: A laboratory study.

    PubMed

    López, Félix A; Román, Carlos Pérez; García-Díaz, Irene; Alguacil, Francisco J

    2015-09-01

    This work reports the oxidation behaviour and waste-to-energy output of different semi-rigid and flexible aluminium packagings when incinerated at 850°C in an air atmosphere enriched with 6% oxygen, in the laboratory setting. The physical properties of the different packagings were determined, including their metallic aluminium contents. The ash contents of their combustion products were determined according to standard BS ISO 1171:2010. The net calorific value, the required energy, and the calorific gain associated with each packaging type were determined following standard BS EN 13431:2004. Packagings with an aluminium lamina thickness of >50μm did not fully oxidise. During incineration, the weight-for-weight waste-to-energy output of the packagings with thick aluminium lamina was lower than that of packagings with thin lamina. The calorific gain depended on the degree of oxidation of the metallic aluminium, but was greater than zero for all the packagings studied. Waste aluminium may therefore be said to act as an energy source in municipal solid waste incineration systems.

  4. Galvanic corrosion behaviour of aluminium 3004 and copper in tropical marine atmosphere

    NASA Astrophysics Data System (ADS)

    Subramanian, G.; Palraj, S.; Palanichamy, S.

    2014-06-01

    The galvanic corrosion behaviour of aluminium 3004 and copper with different area ratios were studied in the tropical marine atmosphere at Tuticorin harbour over a period of 426 days. The area ratios of A Al: A Cu, studied were 1:1, 1:2, 1:4, 1:8, 2:1, 4:1 & 8:1. The galvanic corrosion behaviour of metals was studied in terms of relative increase in the corrosion rate of aluminium due to galvanic coupling with copper, relative decrease in the corrosion rate of copper due to galvanic coupling with aluminium, and the susceptibility of aluminium to pitting owing to galvanic coupling with copper. The galvanic potential and galvanic current of the system were monitored. Pits of different dimensions ranging from mild etchings to perforations were experienced on the borders and the surfaces of the interface of aluminium in contact with copper. The weathering parameters and the environmental pollutants which have a major role in influencing the galvanic corrosion of metals were also monitored. The corrosion products resulting from galvanic corrosion were analysed using XRD and the pitting on aluminium resulting from galvanic corrosion has been highlighted in terms of pit depth, size and density of pit, using a high resolution microscope.

  5. Two hundred years of aluminum ... or is it aluminium?

    NASA Astrophysics Data System (ADS)

    Kvande, Halvor

    2008-08-01

    Two hundred years ago the word aluminum was used for the first time when a new metal was produced by the English chemist Sir Humphry Davy. Later work has shown that this metal was not pure, but rather an aluminum-iron alloy. This article commemorates the anniversary of aluminum production with a look back at the metal’s origins.

  6. Effect of aluminium toxicity on growth responses and antioxidant activities in Gmelina arborea Roxb. inoculated with AM fungi.

    PubMed

    Dudhane, Mayura; Borde, Mahesh; Jite, Paramjit Kaur

    2012-08-01

    Arbuscular mycorrhizal fungi alleviating the adverse Aluminium effects on growth and antioxidant activity was tested in Gmelina plants. Under greenhouse and aluminium stress condition, the mycorrhizal Gmelina plants showed good growth as compared to non mycorrhizal Gmelina plants. Mycorrhizal colonization in Gmelina was found not to be significantly influenced by aluminium concentrations. Results also indicate that symbiotic association was successfully established between Glomus intraradices and Gmelina plants and mycorrhizal colonization consequently increased the biomass of Gmelina. The root proline accumulation was found to increase in mycorrhizal Gmelina plants for osmotic adjustment of stress tissues under first and second level of Aluminium stress. It was observed that Mycorrhizal colonization increased the shoot root Peroxidase and Superoxide dismutase activities in mycorrhizal Gmelina under second level of Aluminium stress. Mycorrhizal fungi play a major role in phytostabilization by secreting one of the glycoprotein, i.e., Glomalin, which stabilizes the Aluminium in soil as well as in the roots of Gmelina plants.

  7. Aluminium content of some processed foods, raw materials and food additives in China by inductively coupled plasma-mass spectrometry.

    PubMed

    Deng, Gui-Fang; Li, Ke; Ma, Jing; Liu, Fen; Dai, Jing-Jing; Li, Hua-Bin

    2011-01-01

    The level of aluminium in 178 processed food samples from Shenzhen city in China was evaluated using inductively coupled plasma-mass spectrometry. Some processed foods contained a concentration of up to 1226 mg/kg, which is about 12 times the Chinese food standard. To establish the main source in these foods, Al levels in the raw materials were determined. However, aluminium concentrations in raw materials were low (0.10-451.5 mg/kg). Therefore, aluminium levels in food additives used in these foods was determined and it was found that some food additives contained a high concentration of aluminium (0.005-57.4 g/kg). The results suggested that, in the interest of public health, food additives containing high concentrations of aluminium should be replaced by those containing less. This study has provided new information on aluminium levels in Chinese processed foods, raw materials and a selection of food additives.

  8. Determining the aluminium occupancy on the active T-sites in zeolites using X-ray standing waves

    NASA Astrophysics Data System (ADS)

    van Bokhoven, Jeroen A.; Lee, Tien-Lin; Drakopoulos, Michael; Lamberti, Carlo; Thieß, Sebastian; Zegenhagen, Jörg

    2008-07-01

    Zeolites are microporous crystalline materials that find wide application in industry, for example, as catalysts and gas separators, and in our daily life, for example, as adsorbents or as ion exchangers in laundry detergents. The tetrahedrally coordinated silicon and aluminium atoms in the zeolite unit cell occupy the so-called crystallographic T-sites. Besides their pore size, the occupation of specific T-sites by the aluminium atoms determines the performance of the zeolites. Despite its importance, the distribution of aluminium over the crystallographic T-sites remains one of the most challenging, unresolved issues in zeolite science. Here, we report how to determine unambiguously and directly the distribution of aluminium in zeolites by means of the X-ray standing wave technique using brilliant, focused X-rays from a third-generation synchrotron source. We report in detail the analysis of the aluminium distribution in scolecite, which demonstrates how the aluminium occupancy in zeolites can systematically be determined.

  9. Lead-free bearing alloys for engine applications

    NASA Astrophysics Data System (ADS)

    Ratke, Lorenz; Ågren, John; Ludwig, Andreas; Tonn, Babette; Gránásy, László; Mathiesen, Ragnvald; Arnberg, Lars; Anger, Gerd; Reifenhäuser, Bernd; Lauer, Michael; Garen, Rune; Gust, Edgar

    2005-10-01

    Recent developments to reduce the fuel consumption, emission and air pollution, size and weight of engines for automotive, truck, ship propulsion and electrical power generation lead to temperature and load conditions within the engines that cannot be borne by conventional bearings. Presently, only costly multilayer bearings with electroplated or sputtered surface coatings can cope with the load/speed combinations required. Ecological considerations in recent years led to a ban by the European Commission on the use of lead in cars a problem for the standard bronze-lead bearing material. This MAP project is therefore developing an aluminium-based lead-free bearing material with sufficient hardness, wear and friction properties and good corrosion resistance. Only alloys made of components immiscible in the molten state can meet the demanding requirements. Space experimentation plays a crucial role in optimising the cast microstructure for such applications.

  10. Low elastic modulus Ti-Ta alloys for load-bearing permanent implants: enhancing the biodegradation resistance by electrochemical surface engineering.

    PubMed

    Kesteven, Jazmin; Kannan, M Bobby; Walter, Rhys; Khakbaz, Hadis; Choe, Han-Choel

    2015-01-01

    In this study, the in vitro degradation behaviour of titanium-tantalum (Ti-Ta) alloys (10-30 wt.% Ta) was investigated and compared with conventional implant materials, i.e., commercially pure titanium (Cp-Ti) and titanium-aluminium-vanadium (Ti6Al4V) alloy. Among the three Ti-Ta alloys studied, the Ti20Ta (6.3×10(-4) mm/y) exhibited the lowest degradation rate, followed by Ti30Ta (1.2×10(-3) mm/y) and Ti10Ta (1.4×10(-3) mm/y). All the Ti-Ta alloys exhibited lower degradation rate than that of Cp-Ti (1.8×10(-3) mm/y), which suggests that Ta addition to Ti is beneficial. As compared to Ti6Al4V alloy (8.1×10(-4) mm/y), the degradation rate of Ti20Ta alloy was lower by ~22%. However, the Ti30Ta alloy, which has closer elastic modulus to that of natural bone, showed ~48% higher degradation rate than that of Ti6Al4V alloy. Hence, to improve the degradation performance of Ti30Ta alloy, an intermediate thin porous layer was formed electrochemically on the alloy followed by calcium phosphate (CaP) electrodeposition. The coated Ti30Ta alloy (3.8×10(-3) mm/y) showed ~53% lower degradation rate than that of Ti6Al4V alloy. Thus, the study suggests that CaP coated Ti30Ta alloy can be a viable material for load-bearing permanent implants.

  11. Surface alloying of Mg alloys after surface nanocrystallization.

    PubMed

    Zhang, Ming-Xing; Shi, Yi-Nong; Sun, Haiqing; Kelly, Patrick M

    2008-05-01

    Surface nanocrystallization using a surface mechanical attrition treatment effectively activates the surface of magnesium alloys due to the increase in grain boundary diffusion channels. As a result, the temperature of subsequent surface alloying treatment of pure Mg and AZ91 alloy can be reduced from 430 degrees C to 380 degrees C. Thus, it is possible to combine the surface alloying process with the solution treatment for this type of alloy. After surface alloying, the hardness of the alloyed layer is 3 to 4 times higher than that of the substrate and this may significantly improve the wear resistance of magnesium alloys.

  12. Catalyst Alloys Processing

    NASA Astrophysics Data System (ADS)

    Tan, Xincai

    2014-10-01

    Catalysts are one of the key materials used for diamond formation at high pressures. Several such catalyst products have been developed and applied in China and around the world. The catalyst alloy most widely used in China is Ni70Mn25Co5 developed at Changsha Research Institute of Mining and Metallurgy. In this article, detailed techniques for manufacturing such a typical catalyst alloy will be reviewed. The characteristics of the alloy will be described. Detailed processing of the alloy will be presented, including remelting and casting, hot rolling, annealing, surface treatment, cold rolling, blanking, finishing, packaging, and waste treatment. An example use of the catalyst alloy will also be given. Industrial experience shows that for the catalyst alloy products, a vacuum induction remelt furnace can be used for remelting, a metal mold can be used for casting, hot and cold rolling can be used for forming, and acid pickling can be used for metal surface cleaning.

  13. Aluminium reduces sugar uptake in tobacco cell cultures: a potential cause of inhibited elongation but not of toxicity.

    PubMed

    Abdel-Basset, Refat; Ozuka, Shotaro; Demiral, Tijen; Furuichi, Takuya; Sawatani, Ikuo; Baskin, Tobias I; Matsumoto, Hideaki; Yamamoto, Yoko

    2010-06-01

    Aluminium is well known to inhibit plant elongation, but the role in this inhibition played by water relations remains unclear. To investigate this, tobacco (Nicotiana tabacum L.) suspension-cultured cells (line SL) was used, treating them with aluminium (50 microM) in a medium containing calcium, sucrose, and MES (pH 5.0). Over an 18 h treatment period, aluminium inhibited the increase in fresh weight almost completely and decreased cellular osmolality and internal soluble sugar content substantially; however, aluminium did not affect the concentrations of major inorganic ions. In aluminium-treated cultures, fresh weight, soluble sugar content, and osmolality decreased over the first 6 h and remained constant thereafter, contrasting with their continued increases in the untreated cultures. The rate of sucrose uptake, measured by radio-tracer, was reduced by approximately 60% within 3 h of treatment. Aluminium also inhibited glucose uptake. In an aluminium-tolerant cell line (ALT301) isogenic to SL, all of the above-mentioned changes in water relations occurred and tolerance emerged only after 6 h and appeared to involve the suppression of reactive oxygen species. Further separating the effects of aluminium on elongation and cell survival, sucrose starvation for 18 h inhibited elongation and caused similar changes in cellular osmolality but stimulated the production of neither reactive oxygen species nor callose and did not cause cell death. We propose that the inhibition of sucrose uptake is a mechanism whereby aluminium inhibits elongation, but does not account for the induction of cell death.

  14. Effect of aluminium on migratory and invasive properties of MCF-7 human breast cancer cells in culture.

    PubMed

    Darbre, Philippa D; Bakir, Ayse; Iskakova, Elzira

    2013-11-01

    Aluminium (Al) has been measured in human breast tissue, nipple aspirate fluid and breast cyst fluid, and recent studies have shown that at tissue concentrations, aluminium can induce DNA damage and suspension growth in human breast epithelial cells. This paper demonstrates for the first time that exposure to aluminium can also increase migratory and invasive properties of MCF-7 human breast cancer cells. Long-term (32 weeks) but not short-term (1 week) exposure of MCF-7 cells to 10(-4) M aluminium chloride or 10(-4) M aluminium chlorohydrate increased motility of the cells as measured by live cell imaging (cumulative length moved by individual cells), by a wound healing assay and by migration in real time through 8 μm pores of a membrane using xCELLigence technology. Long-term exposure (37 weeks) to 10(-4) M aluminium chloride or 10(-4) M aluminium chlorohydrate also increased the ability of MCF-7 cells to invade through a matrigel layer as measured in real time using the xCELLigence system. Although molecular mechanisms remain to be characterized, the ability of aluminium salts to increase migratory and invasive properties of MCF-7 cells suggests that the presence of aluminium in the human breast could influence metastatic processes. This is important because mortality from breast cancer arises mainly from tumour spread rather than from the presence of a primary tumour in the breast.

  15. High-power laser diodes based on InGaAsP alloys

    NASA Astrophysics Data System (ADS)

    Razeghi, Manijeh

    1994-06-01

    HIGH-POWER, high-coherence solid-state lasers, based on dielectric materials such as ruby or Nd:YAG (yttrium aluminium garnet), have many civilian and military applications. The active media in these lasers are insulating, and must therefore be excited (or `pumped') by optical, rather than electrical, means. Conventional gas-discharge lamps can be used as the pumping source, but semiconductor diode lasers are more efficient, as their wavelength can be tailored to match the absorption properties of the lasing material. Semiconducting AlGaAs alloys are widely used for this purpose1, 2, but oxidation of the aluminium and the spreading of defects during device operation limit the lifetime of the diodes3, and hence the reliability of the system as a whole. Aluminium-free InGaAsP compounds, on the other hand, do not have these lifetime-limiting properties4-8. We report here the fabrication of high-power lasers based on InGaAsP (lattice-matched to GaAs substrates), which operate over the same wavelength range as conventional AlGaAs laser diodes and show significantly improved reliability. The other optical and electrical properties of these diodes are either comparable or superior to those of the AlGaAs system.

  16. Low activation ferritic alloys

    DOEpatents

    Gelles, David S.; Ghoniem, Nasr M.; Powell, Roger W.

    1986-01-01

    Low activation ferritic alloys, specifically bainitic and martensitic stainless steels, are described for use in the production of structural components for nuclear fusion reactors. They are designed specifically to achieve low activation characteristics suitable for efficient waste disposal. The alloys essentially exclude molybdenum, nickel, nitrogen and niobium. Strength is achieved by substituting vanadium, tungsten, and/or tantalum in place of the usual molybdenum content in such alloys.

  17. Low activation ferritic alloys

    DOEpatents

    Gelles, D.S.; Ghoniem, N.M.; Powell, R.W.

    1985-02-07

    Low activation ferritic alloys, specifically bainitic and martensitic stainless steels, are described for use in the production of structural components for nuclear fusion reactors. They are designed specifically to achieve low activation characteristics suitable for efficient waste disposal. The alloys essentially exclude molybdenum, nickel, nitrogen and niobium. Strength is achieved by substituting vanadium, tungsten, and/or tantalum in place of the usual molybdenum content in such alloys.

  18. Amorphous metal alloy

    DOEpatents

    Wang, R.; Merz, M.D.

    1980-04-09

    Amorphous metal alloys of the iron-chromium and nickel-chromium type have excellent corrosion resistance and high temperature stability and are suitable for use as a protective coating on less corrosion resistant substrates. The alloys are stabilized in the amorphous state by one or more elements of titanium, zirconium, hafnium, niobium, tantalum, molybdenum, and tungsten. The alloy is preferably prepared by sputter deposition.

  19. PLUTONIUM-ZIRCONIUM ALLOYS

    DOEpatents

    Schonfeld, F.W.; Waber, J.T.

    1960-08-30

    A series of nuclear reactor fuel alloys consisting of from about 5 to about 50 at.% zirconium (or higher zirconium alloys such as Zircaloy), balance plutonium, and having the structural composition of a plutonium are described. Zirconium is a satisfactory diluent because it alloys readily with plutonium and has desirable nuclear properties. Additional advantages are corrosion resistance, excellent fabrication propenties, an isotropie structure, and initial softness.

  20. NICKEL-BASE ALLOY

    DOEpatents

    Inouye, H.; Manly, W.D.; Roche, T.K.

    1960-01-19

    A nickel-base alloy was developed which is particularly useful for the containment of molten fluoride salts in reactors. The alloy is resistant to both salt corrosion and oxidation and may be used at temperatures as high as 1800 deg F. Basically, the alloy consists of 15 to 22 wt.% molybdenum, a small amount of carbon, and 6 to 8 wt.% chromium, the balance being nickel. Up to 4 wt.% of tungsten, tantalum, vanadium, or niobium may be added to strengthen the alloy.