Science.gov

Sample records for 2d tungsten oxide

  1. Preparation of tungsten oxide

    DOEpatents

    Bulian, Christopher J.; Dye, Robert C.; Son, Steven F.; Jorgensen, Betty S.; Perry, W. Lee

    2009-09-22

    Tungsten trioxide hydrate (WO.sub.3.H.sub.2O) was prepared from a precursor solution of ammonium paratungstate in concentrated aqueous hydrochloric acid. The precursor solution was rapidly added to water, resulting in the crash precipitation of a yellow white powder identified as WO.sub.3.H.sub.2O nanosized platelets by x-ray diffraction and scanning electron microscopy. Annealing of the powder at 200.degree. C. provided cubic phase WO.sub.3 nanopowder, and at 400.degree. C. provided WO.sub.3 nanopowder as a mixture of monoclinic and orthorhombic phases.

  2. Some Tungsten Oxidation-Reduction Chemistry: A Paint Pot Titration.

    ERIC Educational Resources Information Center

    Pickering, Miles; Monts, David L.

    1982-01-01

    Reports an oxidation-reduction experiment using tungsten, somewhat analogous to the classical student experiment involving oxidation-reduction of vanadium. Includes experimental procedures, results, and toxicity/cost of tungsten compounds. (Author/JN)

  3. Seed growth of tungsten diselenide nanotubes from tungsten oxides.

    PubMed

    Kim, Hyun; Yun, Seok Joon; Park, Jin Cheol; Park, Min Ho; Park, Ji-Hoon; Kim, Ki Kang; Lee, Young Hee

    2015-05-13

    We report growth of tungsten diselenide (WSe2) nanotubes by chemical vapor deposition with a two-zone furnace. WO3 nanowires were first grown by annealing tungsten thin films under argon ambient. WSe2 nanotubes were then grown at the tips of WO3 nanowires through selenization via two steps: (i) formation of tubular WSe2 structures on the outside of WO3 nanowires, resulting in core (WO3)-shell (WSe2) and (ii) growth of WSe2 nanotubes at the tips of WO3 nanowires. The observed seed growth is markedly different from existing substitutional growth of WSe2 nanotubes, where oxygen atoms are replaced by selenium atoms in WO3 nanowires to form WSe2 nanotubes. Another advantage of our growth is that WSe2 film was grown by simply supplying hydrogen gas, where the native oxides were reduced to thin film instead of forming oxide nanowires. Our findings will contribute to engineer other transition metal dichacogenide growth such as MoS2, WS2, and MoSe2. PMID:25581340

  4. Penetration of tungsten-alloy rods into composite ceramic targets: Experiments and 2-D simulations

    SciTech Connect

    Rosenberg, Z.; Dekel, E.; Hohler, V.; Stilp, A. J.; Weber, K.

    1998-07-10

    A series of terminal ballistics experiments, with scaled tungsten-alloy penetrators, was performed on composite targets consisting of ceramic tiles glued to thick steel backing plates. Tiles of silicon-carbide, aluminum nitride, titanium-dibroide and boron-carbide were 20-80 mm thick, and impact velocity was 1.7 km/s. 2-D numerical simulations, using the PISCES code, were performed in order to simulate these shots. It is shown that a simplified version of the Johnson-Holmquist failure model can account for the penetration depths of the rods but is not enough to capture the effect of lateral release waves on these penetrations.

  5. 40 CFR 721.10168 - Cesium tungsten oxide.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Cesium tungsten oxide. 721.10168... Substances § 721.10168 Cesium tungsten oxide. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as cesium tungsten oxide (PMN P-08-275; CAS No....

  6. 40 CFR 721.10168 - Cesium tungsten oxide.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Cesium tungsten oxide. 721.10168... Substances § 721.10168 Cesium tungsten oxide. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as cesium tungsten oxide (PMN P-08-275; CAS No....

  7. 40 CFR 721.10168 - Cesium tungsten oxide.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Cesium tungsten oxide. 721.10168... Substances § 721.10168 Cesium tungsten oxide. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as cesium tungsten oxide (PMN P-08-275; CAS No....

  8. 40 CFR 721.10168 - Cesium tungsten oxide.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Cesium tungsten oxide. 721.10168... Substances § 721.10168 Cesium tungsten oxide. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as cesium tungsten oxide (PMN P-08-275; CAS No....

  9. 40 CFR 721.10168 - Cesium tungsten oxide.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Cesium tungsten oxide. 721.10168... Substances § 721.10168 Cesium tungsten oxide. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as cesium tungsten oxide (PMN P-08-275; CAS No....

  10. Growth of tungsten oxide on carbon nanowalls templates

    SciTech Connect

    Wang, Hua; Su, Yan; Chen, Shuo; Quan, Xie

    2013-03-15

    Highlights: ► Tungsten oxide deposited on carbon nanowalls by hot filament chemical vapor deposition technique. ► This composite has two-dimensional uniform morphology with a crystalline structure of monoclinic tungsten trioxide. ► Surface photoelectric voltage measurements show that this product has photoresponse properties. - Abstract: In the present work we present a simple approach for coupling tungsten oxide with carbon nanowalls. The two-dimensional carbon nanowalls with open boundaries were grown using plasma enhanced hot filament chemical vapor deposition, and the subsequent tungsten oxide growth was performed in the same equipment by direct heating of a tungsten filament. The tungsten oxide coating is found to have uniform morphology with a crystalline structure of monoclinic tungsten trioxide. Surface photoelectric voltage measurements show that this product has photoresponse properties. The method of synthesis described here provides an operable route to the production of two-dimensional tungsten oxide nanocomposites.

  11. Application of 2D Non-Graphene Materials and 2D Oxide Nanostructures for Biosensing Technology

    PubMed Central

    Shavanova, Kateryna; Bakakina, Yulia; Burkova, Inna; Shtepliuk, Ivan; Viter, Roman; Ubelis, Arnolds; Beni, Valerio; Starodub, Nickolaj; Yakimova, Rositsa; Khranovskyy, Volodymyr

    2016-01-01

    The discovery of graphene and its unique properties has inspired researchers to try to invent other two-dimensional (2D) materials. After considerable research effort, a distinct “beyond graphene” domain has been established, comprising the library of non-graphene 2D materials. It is significant that some 2D non-graphene materials possess solid advantages over their predecessor, such as having a direct band gap, and therefore are highly promising for a number of applications. These applications are not limited to nano- and opto-electronics, but have a strong potential in biosensing technologies, as one example. However, since most of the 2D non-graphene materials have been newly discovered, most of the research efforts are concentrated on material synthesis and the investigation of the properties of the material. Applications of 2D non-graphene materials are still at the embryonic stage, and the integration of 2D non-graphene materials into devices is scarcely reported. However, in recent years, numerous reports have blossomed about 2D material-based biosensors, evidencing the growing potential of 2D non-graphene materials for biosensing applications. This review highlights the recent progress in research on the potential of using 2D non-graphene materials and similar oxide nanostructures for different types of biosensors (optical and electrochemical). A wide range of biological targets, such as glucose, dopamine, cortisol, DNA, IgG, bisphenol, ascorbic acid, cytochrome and estradiol, has been reported to be successfully detected by biosensors with transducers made of 2D non-graphene materials. PMID:26861346

  12. Application of 2D Non-Graphene Materials and 2D Oxide Nanostructures for Biosensing Technology.

    PubMed

    Shavanova, Kateryna; Bakakina, Yulia; Burkova, Inna; Shtepliuk, Ivan; Viter, Roman; Ubelis, Arnolds; Beni, Valerio; Starodub, Nickolaj; Yakimova, Rositsa; Khranovskyy, Volodymyr

    2016-01-01

    The discovery of graphene and its unique properties has inspired researchers to try to invent other two-dimensional (2D) materials. After considerable research effort, a distinct "beyond graphene" domain has been established, comprising the library of non-graphene 2D materials. It is significant that some 2D non-graphene materials possess solid advantages over their predecessor, such as having a direct band gap, and therefore are highly promising for a number of applications. These applications are not limited to nano- and opto-electronics, but have a strong potential in biosensing technologies, as one example. However, since most of the 2D non-graphene materials have been newly discovered, most of the research efforts are concentrated on material synthesis and the investigation of the properties of the material. Applications of 2D non-graphene materials are still at the embryonic stage, and the integration of 2D non-graphene materials into devices is scarcely reported. However, in recent years, numerous reports have blossomed about 2D material-based biosensors, evidencing the growing potential of 2D non-graphene materials for biosensing applications. This review highlights the recent progress in research on the potential of using 2D non-graphene materials and similar oxide nanostructures for different types of biosensors (optical and electrochemical). A wide range of biological targets, such as glucose, dopamine, cortisol, DNA, IgG, bisphenol, ascorbic acid, cytochrome and estradiol, has been reported to be successfully detected by biosensors with transducers made of 2D non-graphene materials.

  13. Tungsten Oxides for Photocatalysis, Electrochemistry, and Phototherapy.

    PubMed

    Huang, Zhen-Feng; Song, Jiajia; Pan, Lun; Zhang, Xiangwen; Wang, Li; Zou, Ji-Jun

    2015-09-23

    The conversion, storage, and utilization of renewable energy have all become more important than ever before as a response to ever-growing energy and environment concerns. The performance of energy-related technologies strongly relies on the structure and property of the material used. The earth-abundant family of tungsten oxides (WOx ≤3 ) receives considerable attention in photocatalysis, electrochemistry, and phototherapy due to their highly tunable structures and unique physicochemical properties. Great breakthroughs have been made in enhancing the optical absorption, charge separation, redox capability, and electrical conductivity of WOx ≤3 through control of the composition, crystal structure, morphology, and construction of composite structures with other materials, which significantly promotes the efficiency of processes and devices based on this material. Herein, the properties and synthesis of WOx ≤3 family are reviewed, and then their energy-related applications are highlighted, including solar-light-driven water splitting, CO2 reduction, and pollutant removal, electrochromism, supercapacitors, lithium batteries, solar and fuel cells, non-volatile memory devices, gas sensors, and cancer therapy, from the aspect of function-oriented structure design and control.

  14. Growth of tungsten oxide nanorods with carbon caps.

    PubMed

    Kichambare, Padmakar; Hii, King-Fu; Vallance, R Ryan; Sadanadan, B; Rao, Apparao M; Javed, Kazi; Menguc, M Pinar

    2006-02-01

    Hybrid nanostructures consisting of tungsten oxide nanorods with mushroom-shaped carbon caps were grown on electrochemically etched tungsten tips by thermal chemical vapor deposition with methane and argon. These nanorods grow along the radial direction and are very straight and smooth. Electron microscopy revealed a dominant diameter and length of approximately 50 nm and approximately 0.6 microm, respectively. High-resolution transmission electron microscopy (HRTEM), and electron energy loss spectroscopy (EELS) revealed the presence of crystalline monoclinic W18O49 in the nanorods, and the cap was entirely amorphous carbon. A plausible growth mechanism involves the reduction of tungsten oxide WO3, present on the tungsten surface, by methane at 900 degrees C. PMID:16573057

  15. Tungsten

    SciTech Connect

    1996-08-01

    The name tungsten, derived from the Swedish words {open_quotes}tung{close_quotes} and {open_quotes}sten{close_quotes}, meaning heavy stone, was first applied to a tungsten-containing mineral in 1755. The mineral, itself, was subsequently identified by C.W. Scheele in 1781, and named scheelite. Metallic tungsten was first isolated from the mineral wolframite in 1783, and given the German name {open_quotes}wolfram,{close_quotes} which remains an alternative name for the element. Ultimately, the English word, tungsten, became the official name, while W remains the element`s chemical symbol. This article discusses the geology, exploitation, applications, and market overview of tungsten.

  16. High temperature heterogeneous reaction kinetics and mechanisms of tungsten oxidation

    NASA Astrophysics Data System (ADS)

    Sabourin, Justin L.

    Tungsten, which is a material used in many high temperature applications, is limited by its susceptibility to oxidation at elevated temperatures. Although tungsten has the highest melting temperature of any metal, at much lower temperatures volatile oxides are formed during oxidation with oxygen containing species. This differs from many heterogeneous oxidation reactions involving metals since most reactions form very stable oxides that have higher melting or boiling points than the pure metal (e.g., aluminum, iron). Understanding heterogeneous oxidation and vaporization processes may allow for the expansion and improvement of high temperature tungsten applications. In order to increase understanding of the oxidation processes of tungsten, there is a need to develop reaction mechanisms and kinetics for oxidation processes involving oxidizers and environmental conditions of interest. Tungsten oxidation was thoroughly studied in the past, and today there is a good phenomenological understanding of these processes. However, as the design of large scale systems increasingly relies on computer modeling there becomes a need for improved descriptions of chemical reactions. With the increase in computing power over the last several decades, and the development of quantum chemistry and physics theories, heterogeneous systems can be modeled in detail at the molecular level. Thermochemical parameters that may not be measured experimentally may now be determined theoretically, a tool that was previously unavailable to scientists and engineers. Additionally, chemical kinetic modeling software is now available for both homogeneous and heterogeneous reactions. This study takes advantage of these new theoretical tools, as well as a thermogravimetric (TG) flow reactor developed as part of this study to learn about mechanisms and kinetics of tungsten oxidation. Oxidizers of interest are oxygen (O2), carbon dioxide (CO 2), water (H2O), and other oxidizers present in combustion and

  17. Toxicologic evaluation of tungsten: 28-day inhalation study of tungsten blue oxide in rats.

    PubMed

    Rajendran, Narayanan; Hu, Shu-Chieh; Sullivan, Dennis; Muzzio, Miguel; Detrisac, Carol J; Venezia, Carmen

    2012-12-01

    The toxicity and toxicokinetics of tungsten blue oxide (TBO) were examined. TBO is an intermediate in the production of tungsten powder, and has shown the potential to cause cellular damage in in vitro studies. However, in vivo evidence seems to indicate a lack of adverse effects. The present study was undertaken to address the dearth of longer-term inhalation toxicity studies of tungsten oxides by investigating the biological responses induced by TBO when administered via nose-only inhalation to rats at levels of 0.08, 0.325, and 0.65 mg TBO/L of air for 6 h/day for 28 consecutive days, followed by a 14-day recovery period. Inhaled TBO was absorbed systemically and blood levels of tungsten increased as inhaled concentration increased. Among the tissues analyzed for tungsten levels, lung, femur and kidney showed increased levels, with lung at least an order of magnitude greater than kidney or femur. By exposure day 14, tungsten concentration in tissues had reached steady-state. Increased lung weight was noted for both terminal and recovery animals and was attributed to deposition of TBO in the lungs, inducing a macrophage influx. Microscopic evaluation of tissues revealed a dose-related increase in alveolar pigmented macrophages, alveolar foreign material and individual alveolar foamy macrophages in lung. After a recovery period there was a slight reduction in the incidence and severity of histopathological findings. Based on the absence of other adverse effects, the increased lung weights and the microscopic findings were interpreted as nonadverse response to exposure and were not considered a specific reaction to TBO.

  18. 2D tritium distribution on tungsten tiles used in JET ITER-like wall project

    NASA Astrophysics Data System (ADS)

    Hatano, Y.; Widdowson, A.; Bekris, N.; Ayres, C.; Baron-Wiechec, A.; Likonen, J.; Koivuranta, S.; Ikonen, J.; Yumizuru, K.

    2015-08-01

    Post-mortem measurements of 2-dimensional tritium (T) distribution using an imaging plate (IP) technique were performed for tungsten (W) divertor tiles (W-coated CFC) used in JET-ITER like wall (ILW) project. The observed T distributions were clearly inhomogeneous, and there were band-like regions with high T concentrations that extended in the toroidal direction on tiles 1, 3, 4 and 6. The concentrations of T in the band-like regions were higher by an order of magnitude than the concentrations in other parts. The inhomogeneous T distributions were explained by non-uniform co-deposition with other elements such as beryllium. The concentrations of T on the outboard vertical tiles (tiles 7 and 8) were low and relatively uniform in comparison with other tiles.

  19. Targeted fluorescence imaging enhanced by 2D materials: a comparison between 2D MoS2 and graphene oxide.

    PubMed

    Xie, Donghao; Ji, Ding-Kun; Zhang, Yue; Cao, Jun; Zheng, Hu; Liu, Lin; Zang, Yi; Li, Jia; Chen, Guo-Rong; James, Tony D; He, Xiao-Peng

    2016-08-01

    Here we demonstrate that 2D MoS2 can enhance the receptor-targeting and imaging ability of a fluorophore-labelled ligand. The 2D MoS2 has an enhanced working concentration range when compared with graphene oxide, resulting in the improved imaging of both cell and tissue samples.

  20. Highly efficient supercapacitor electrode with two-dimensional tungsten disulfide and reduced graphene oxide hybrid nanosheets

    NASA Astrophysics Data System (ADS)

    Tu, Chao-Chi; Lin, Lu-Yin; Xiao, Bing-Chang; Chen, Yu-Shiang

    2016-07-01

    Two-dimensional (2D) nanostructures with their high surface area and large in-plane conductivity have been regarded as promising materials for supercapacitors (SCs). Tungsten disulfide (WS2) is highly suitable for charge accumulation with its abundant active sites in the interspacing between the 2D structures and the intraspacing of each atomic layer, as well as on the tungsten centers with the charges generated by the Faradaic reactions. This study proposes the preparation of well-constructed WS2/reduced graphene oxide (RGO) nanosheets using a simple molten salt process as the electroactive material for SCs, which presents a high specific capacitance (CF) of 2508.07 F g-1 at the scan rate of 1 mV s-1, because of the synergic effect of WS2 with its large charge-accumulating sites on the 2D planes and RGO with its highly enhanced conductivity and improved connections in the WS2 networks. The excellent cycling stability of 98.6% retention after 5000 cycles charge/discharge process and the Coulombic efficiency close to 100% for the entire measurement are also achieved for the WS2/RGO-based SC electrode. The results suggest the potential for the combination of the 2D metal sulfide and carbon materials as the charge storage material to solve the energy problems and attain a sustainable society.

  1. 40 CFR 721.10599 - Calcium cobalt lead titanium tungsten oxide.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Calcium cobalt lead titanium tungsten... Specific Chemical Substances § 721.10599 Calcium cobalt lead titanium tungsten oxide. (a) Chemical... cobalt lead titanium tungsten oxide (PMN P-11-271; CAS No. 1262279-31-1) is subject to reporting...

  2. 40 CFR 721.10599 - Calcium cobalt lead titanium tungsten oxide.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Calcium cobalt lead titanium tungsten... Specific Chemical Substances § 721.10599 Calcium cobalt lead titanium tungsten oxide. (a) Chemical... cobalt lead titanium tungsten oxide (PMN P-11-271; CAS No. 1262279-31-1) is subject to reporting...

  3. Amorphous copper tungsten oxide with tunable band gaps

    SciTech Connect

    Chen Le; Shet, Sudhakar; Tang Houwen; Wang Heli; Yan Yanfa; Turner, John; Al-Jassim, Mowafak; Ahn, Kwang-soon

    2010-08-15

    We report on the synthesis of amorphous copper tungsten oxide thin films with tunable band gaps. The thin films are synthesized by the magnetron cosputtering method. We find that due to the amorphous nature, the Cu-to-W ratio in the films can be varied without the limit of the solubility (or phase separation) under appropriate conditions. As a result, the band gap and conductivity type of the films can be tuned by controlling the film composition. Unfortunately, the amorphous copper tungsten oxides are not stable in aqueous solution and are not suitable for the application of photoelectrochemical splitting of water. Nonetheless, it provides an alternative approach to search for transition metal oxides with tunable band gaps.

  4. Silicon and tungsten oxide nanostructures for water splitting

    NASA Astrophysics Data System (ADS)

    Reyes Gil, Karla R.; Spurgeon, Joshua M.; Lewis, Nathan S.

    2009-08-01

    Inorganic semiconductors are promising materials for driving photoelectrochemical water-splitting reactions. However, there is not a single semiconductor material that can sustain the unassisted splitting of water into H2 and O2. Instead, we are developing a three part cell design where individual catalysts for water reduction and oxidation will be attached to the ends of a membrane. The job of splitting water is therefore divided into separate reduction and oxidation reactions, and each catalyst can be optimized independently for a single reaction. Silicon might be suitable to drive the water reduction. Inexpensive highly ordered Si wire arrays were grown on a single crystal wafer and transferred into a transparent, flexible polymer matrix. In this array, light would be absorbed along the longer axial dimension while the resulting electrons or holes would be collected along the much shorter radial dimension in a massively parallel array resembling carpet fibers on a microscale, hence the term "solar carpet". Tungsten oxide is a good candidate to drive the water oxidation. Self-organized porous tungsten oxide was successfully synthesized on the tungsten foil by anodization. This sponge-like structure absorbs light efficiently due to its high surface area; hence we called it "solar sponge".

  5. Growth of Ordered Ultrathin Tungsten Oxide Films on Pt(111)

    SciTech Connect

    Li, Zhenjun; Zhang, Zhenrong; Kim, Yu Kwon; Smith, R. Scott; Netzer, Falko; Kay, Bruce D.; Rousseau, Roger J.; Dohnalek, Zdenek

    2011-04-07

    Ordered tungsten oxide ultra-thin films were prepared on a Pt(111) substrate at 700 K via direct sublimation of monodispersed cyclic (WO3)3 trimers. The surface composition, structure and morphology were determined using a combination of atomically resolved imaging, ensemble-averaged surface-sensitive spectroscopies, and density functional theory (DFT). We find that half of the (WO3)3 tungsten atoms get partially reduced to the (5+) oxidation state in the first layer at the Pt(111) interface. The opening of the (WO3)3 ring leads to the formation of a tungsten oxide layer with a zig-zag chain structure with a c(4×2) periodicity. In the second layer, the (WO3)3 clusters remain intact and form an ordered (3×3) array of molecularly-bound (WO3)3. DFT calculations provide a detailed understanding of the structure, oxidation states, and the vibrational frequencies for both the c(4×2) and (3×3) overlayers.

  6. Thermal oxidation of tungsten-based sputtered coatings

    SciTech Connect

    Louro, C.; Cavaleiro, A.

    1997-01-01

    The effect of the addition of nickel, titanium, and nitrogen on the air oxidation behavior of W-based sputtered coatings in the temperature range 600 to 800 C was studied. In some cases these additions significantly improved the oxidation resistance of the tungsten coatings. As reported for bulk tungsten, all the coatings studied were oxidized by layers following a parabolic law. Besides WO{sub 3} and WO{sub x} phases detected in all the oxidized coatings, TiO{sub 2} and NiWO{sub 4} were also detected for W-Ti and W-Ni films, respectively. WO{sub x} was present as an inner protective compact layer covered by the porous WO{sub 3} oxide. The best oxidation resistance was found for W-Ti and W-N-Ni coatings which also presented the highest activation energies (E{sub a} = 234 and 218 kJ/mol, respectively, as opposed to E{sub a} {approx} 188 kJ/mol for the other coatings). These lower oxidation weight gains were attributed to the greater difficulty of the inward diffusion of oxygen ions for W-Ti films, owing to the formation of fine particles of TiO{sub 2}, and the formation of the external, more protective layer of NiWO{sub 4} for W-N-Ni coatings.

  7. Studies on nickel-tungsten oxide thin films

    SciTech Connect

    Usha, K. S.; Sivakumar, R.; Sanjeeviraja, C.

    2014-10-15

    Nickel-Tungsten oxide (95:5) thin films were prepared by rf sputtering at 200W rf power with various substrate temperatures. X-ray diffraction study reveals the amorphous nature of films. The substrate temperature induced decrease in energy band gap with a maximum transmittance of 71%1 was observed. The Micro-Raman study shows broad peaks at 560 cm{sup −1} and 1100 cm{sup −1} correspond to Ni-O vibration and the peak at 860 cm{sup −1} can be assigned to the vibration of W-O-W bond. Photoluminescence spectra show two peaks centered on 420 nm and 485 nm corresponding to the band edge emission and vacancies created due to the addition of tungsten, respectively.

  8. Preparation of size-controlled tungsten oxide nanoparticles and evaluation of their adsorption performance

    SciTech Connect

    Hidayat, Darmawan; Purwanto, Agus; Wang, Wei-Ning; Okuyama, Kikuo

    2010-02-15

    The present study investigated the effects of particle size on the adsorption performance of tungsten oxide nanoparticles. Nanoparticles 18-73 nm in diameter were prepared by evaporation of bulk tungsten oxide particles using a flame spray process. Annealing plasma-made tungsten oxide nanoparticles produced particles with diameters of 7-19 nm. The mechanism of nanoparticle formation for each synthetic route was examined. The low-cost, solid-fed flame process readily produced highly crystalline tungsten oxide nanoparticles with controllable size and a remarkably high adsorption capability. These nanoparticles are comparable to those prepared using the more expensive plasma process.

  9. pH-controllable synthesis of unique nanostructured tungsten oxide aerogel and its sensitive glucose biosensor

    NASA Astrophysics Data System (ADS)

    Sun, Qiang-Qiang; Xu, Maowen; Bao, Shu-Juan; Li, Chang Ming

    2015-03-01

    This work presents a controllable synthesis of nanowire-networked tungsten oxide aerogels, which was performed by varying the pH in a polyethyleneimine (PEI)-assisted hydrothermal process. An enzyme-tungsten oxide aerogel co-modified electrode shows high activity and selectivity toward glucose oxidation, thus holding great promise for applications in bioelectronics.

  10. pH-controllable synthesis of unique nanostructured tungsten oxide aerogel and its sensitive glucose biosensor.

    PubMed

    Sun, Qiang-Qiang; Xu, Maowen; Bao, Shu-Juan; Li, Chang Ming

    2015-03-20

    This work presents a controllable synthesis of nanowire-networked tungsten oxide aerogels, which was performed by varying the pH in a polyethyleneimine (PEI)-assisted hydrothermal process. An enzyme-tungsten oxide aerogel co-modified electrode shows high activity and selectivity toward glucose oxidation, thus holding great promise for applications in bioelectronics.

  11. Heat of combustion of tantalum-tungsten oxide thermite composites

    SciTech Connect

    Cervantes, Octavio G.; Kuntz, Joshua D.; Gash, Alexander E.; Munir, Zuhair A.

    2010-12-15

    The heat of combustion of two distinctly synthesized stoichiometric tantalum-tungsten oxide energetic composites was investigated by bomb calorimetry. One composite was synthesized using a sol-gel (SG) derived method in which micrometric-scale tantalum is immobilized in a tungsten oxide three-dimensional nanostructured network structure. The second energetic composite was made from the mixing of micrometric-scale tantalum and commercially available (CA) nanometric tungsten oxide powders. The energetic composites were consolidated using the spark plasma sintering (SPS) technique under a 300 MPa pressure and at temperatures of 25, 400, and 500 C. For samples consolidated at 25 C, the density of the CA composite is 61.65 {+-} 1.07% in comparison to 56.41 {+-} 1.19% for the SG derived composite. In contrast, the resulting densities of the SG composite are higher than the CA composite for samples consolidated at 400 and 500 C. The theoretical maximum density for the SG composite consolidated to 400 and 500 C are 81.30 {+-} 0.58% and 84.42 {+-} 0.62%, respectively. The theoretical maximum density of the CA composite consolidated to 400 and 500 C are 74.54 {+-} 0.80% and 77.90 {+-} 0.79%, respectively. X-ray diffraction analyses showed an increase of pre-reaction of the constituents with an increase in the consolidation temperature. The increase in pre-reaction results in lower stored energy content for samples consolidated to 400 and 500 C in comparison to samples consolidated at 25 C. (author)

  12. Scandium oxide coated polycrystalline tungsten studied using emission microscopy and photoelectron spectroscopy.

    PubMed

    Wan, Congshang; Vaughn, Joel M; Sadowski, Jerzy T; Kordesch, Martin E

    2012-08-01

    Thermionic electron emission from 200 to 500 nm thick coatings of scandium oxide on tungsten foil have been examined in thermionic emission microscopy, spectroscopic photoelectron microcopy, synchrotron radiation and ultraviolet photoelectron spectroscopy (UPS). A clear dependence of the scandium oxide-W electron yield on the grain orientation of the polycrystalline tungsten is observed in thermionic emission and photoelectron emission.

  13. 40 CFR 721.10600 - Calcium cobalt lead strontium titanium tungsten oxide.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Calcium cobalt lead strontium titanium... Specific Chemical Substances § 721.10600 Calcium cobalt lead strontium titanium tungsten oxide. (a... calcium cobalt lead strontium titanium tungsten oxide (PMN P-11-272; CAS No. 1262279-30-0) is subject...

  14. 40 CFR 721.10600 - Calcium cobalt lead strontium titanium tungsten oxide.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Calcium cobalt lead strontium titanium... Specific Chemical Substances § 721.10600 Calcium cobalt lead strontium titanium tungsten oxide. (a... calcium cobalt lead strontium titanium tungsten oxide (PMN P-11-272; CAS No. 1262279-30-0) is subject...

  15. Investigation of tungsten doped tin oxide thin film transistors

    NASA Astrophysics Data System (ADS)

    Yang, Jianwen; Meng, Ting; Yang, Zhao; Cui, Can; Zhang, Qun

    2015-11-01

    Tungsten doped tin oxide thin film transistors (TWO-TFTs) were fabricated by radio frequency magnetron sputtering. With TWO thin films as the channel layers, the TFTs show lower off-current and positive shift turn-on voltage than the intrinsic tin oxide TFTs, which can be explained by the reason that W doping is conducive to suppress the carrier concentration of the TWO channel layer. It is important to elect an appropriate channel thickness for improving the TFT performance. The optimum TFT performance in enhancement mode is achieved at W doping content of 2.7 at% and channel thickness of 12 nm, with the saturation mobility, turn-on voltage, subthreshold swing value and on-off current ratio of 5 cm2 V-1 s-1, 0.4 V, 0.4 V/decade and 2.4  ×  106, respectively.

  16. Aerosol-assisted chemical vapor deposition of tungsten oxide films and nanorods from oxo tungsten(VI) fluoroalkoxide precursors.

    PubMed

    Kim, Hankook; Bonsu, Richard O; O'Donohue, Christopher; Korotkov, Roman Y; McElwee-White, Lisa; Anderson, Timothy J

    2015-02-01

    Aerosol-assisted chemical vapor deposition (AACVD) of WOx was demonstrated using the oxo tungsten(VI) fluoroalkoxide single-source precursors, WO[OCCH3(CF3)2]4 and WO[OC(CH3)2CF3]4. Substoichiometric amorphous tungsten oxide thin films were grown on indium tin oxide (ITO) substrates in nitrogen at low deposition temperature (100-250 °C). At growth temperatures above 300 °C, the W18O49 monoclinic crystalline phase was observed. The surface morphology and roughness, visible light transmittance, electrical conductivity, and work function of the tungsten oxide materials are reported. The solvent and carrier gas minimally affected surface morphology and composition at low deposition temperature; however, material crystallinity varied with solvent choice at higher temperatures. The work function of the tungsten oxide thin films grown between 150 and 250 °C was determined to be in the range 5.0 to 5.7 eV, according to ultraviolet photoelectron spectroscopy (UPS). PMID:25569472

  17. Thermopower enhancement by fractional layer control in 2D oxide superlattices.

    PubMed

    Choi, Woo Seok; Ohta, Hiromichi; Lee, Ho Nyung

    2014-10-22

    Precise tuning of the 2D carrier density by using fractional δ-doping of d electrons improves the thermoelectric properties of oxide heterostructures. This promising result can be attributed to the anisotropic band structure in the 2D system, indicating that δ-doped oxide superlattices are good candidates for advanced thermoelectrics.

  18. Nuclear thermionic converter. [tungsten-thorium oxide rods

    NASA Technical Reports Server (NTRS)

    Phillips, W. M.; Mondt, J. F. (Inventor)

    1977-01-01

    Efficient nuclear reactor thermionic converter units are described which can be constructed at low cost and assembled in a reactor which requires a minimum of fuel. Each converter unit utilizes an emitter rod with a fluted exterior, several fuel passages located in the bulges that are formed in the rod between the flutes, and a collector receiving passage formed through the center of the rod. An array of rods is closely packed in an interfitting arrangement, with the bulges of the rods received in the recesses formed between the bulges of other rods, thereby closely packing the nuclear fuel. The rods are constructed of a mixture of tungsten and thorium oxide to provide high power output, high efficiency, high strength, and good machinability.

  19. Growth and field emission of tungsten oxide nanotip arrays on ITO glass substrate

    NASA Astrophysics Data System (ADS)

    Huang, Kai; Pan, Qingtao; Yang, Feng; Ni, Shibi; He, Deyan

    2007-09-01

    High-density and uniformly aligned tungsten oxide nanotip arrays have been deposited by a conventional thermal evaporation on ITO glass substrates without any catalysts or additives. The temperature of substrate was 450-500 °C. It was shown that the tungsten oxide nanotips are single-crystal grown along [0 1 0] direction. For commercial applications, field emission of the tungsten oxide nanotip arrays was characterized in a poor vacuum at room temperature. The field emission behaviors are in agreement with Fowler-Nordheim theory. The turn-on field is 2.8 V μm -1 as d is 0.3 mm. The excellent field emission performances indicated that the tungsten oxide nanotip arrays grown by the present approach are a good candidate for application in vacuum microelectronic devices.

  20. Tantalum-Tungsten Oxide Thermite Composite Prepared by Sol-Gel Synthesis and Spark Plasma Sintering

    SciTech Connect

    Cervantes, O; Kuntz, J; Gash, A; Munir, Z

    2009-02-13

    Energetic composite powders consisting of sol-gel derived nanostructured tungsten oxide were produced with various amounts of micrometer-scale tantalum fuel metal. Such energetic composite powders were ignition tested and results show that the powders are not sensitive to friction, spark and/or impact ignition. Initial consolidation experiments, using the High Pressure Spark Plasma Sintering (HPSPS) technique, on the sol-gel derived nanostructured tungsten oxide produced samples with higher relative density than can be achieved with commercially available tungsten oxide. The sol-gel derived nanostructured tungsten oxide with immobilized tantalum fuel metal (Ta - WO{sub 3}) energetic composite was consolidated to a density of 9.17 g.cm{sup -3} or 93% relative density. In addition those parts were consolidated without significant pre-reaction of the constituents, thus the sample retained its stored chemical energy.

  1. Synthesis, Consolidation and Characterization of Sol-gel Derived Tantalum-Tungsten Oxide Thermite Composites

    SciTech Connect

    Cervantes, O

    2010-06-01

    Energetic composite powders consisting of sol-gel (SG) derived nanostructured tungsten oxide were produced with various amounts of micrometer-scale tantalum fuel metal. Such energetic composite powders were ignition-tested and results show that the powders are not sensitive to friction, spark and/or impact ignition. Initial consolidation experiments, using the High Pressure Spark Plasma Sintering (HPSPS) technique, on the SG derived nanostructured tungsten oxide produced samples with higher relative density than can be achieved with commercially available tungsten oxide. The SG derived nanostructured tungsten oxide with immobilized tantalum fuel metal (Ta - WO3) energetic composite was consolidated to a density of 9.17 g·cm-3 or 93% relative density. In addition, those samples were consolidated without significant pre-reaction of the constituents, thus retaining their stored chemical energy.

  2. Synthesis and electrochemical capacitance of long tungsten oxide nanorod arrays grown vertically on substrate

    SciTech Connect

    Park, Sun Hwa; Kim, Young Heon; Lee, Tae Geol; Shon, Hyun Kyong; Park, Hyun Min; Song, Jae Yong

    2012-11-15

    Highlights: ► Growth of long amorphous tungsten oxide nanorods on a substrate. ► Formation of single-crystalline tungsten oxide nanorods by a heat-treatment. ► High electrochemical pseudocapacitance of 2.8 mF cm{sup −2}. ► Excellent cyclability of psuedocapacitance up to 1000 cycles. -- Abstract: Long tungsten oxide nanorods are vertically grown on Al/W/Ti coated silicon substrates using a two-step anodization process. The first anodization of the Al film forms a mesh-like mask of anodic aluminum oxide, and the second anodization of the W film results in the formation of a buffer layer, a bottom nanorod, and a top nanorod of amorphous tungsten oxide. A pore-widening process prior to the second anodization leads to the enhancement of nanorod length above approximately 500 nm. After a heat-treatment, the tungsten oxide nanorods are crystallized to form a single crystalline structure while the buffer layer forms a polycrystalline structure. The crystalline tungsten oxide nanorods show a cyclic voltammogram retaining the quasi-rectangular shape of an electrochemically reversible faradaic redox reaction, i.e., a typical pseudocapacitive behavior. The maximum electrochemical capacitance per apparent surface area reaches approximately 2.8 mF cm{sup −2} at the voltage scan rate of 20 mV s{sup −1}, and the excellent cyclability of charge–discharge process is maintained up to 1000 cycles.

  3. Morphology modulated growth of bismuth tungsten oxide nanocrystals

    SciTech Connect

    Yao Shushan; Wei, Jiyong; Huang Baibiao Feng Shengyu; Zhang Xiaoyang; Qin Xiaoyan; Wang Peng; Wang Zeyan; Zhang Qi; Jing Xiangyang; Zhan Jie

    2009-02-15

    Two kinds of bismuth tungsten oxide nanocrystals were prepared by microwave hydrothermal method. The morphology modulation of nanocrystals synthesized with precursor suspension's pH varied from 0.25 (strong acid) to 10.05 (base) was studied. The 3D flower like aggregation of Bi{sub 2}WO{sub 6} nanoflakes was synthesized in acid precursor suspension and the nanooctahedron crystals of Bi{sub 3.84}W{sub 0.16}O{sub 6.24} were synthesized in alkalescent precursor. The dominant crystal is changed from Bi{sub 2}WO{sub 6} to Bi{sub 3.84}W{sub 0.16}O{sub 6.24} when the precursor suspension changes from acid to alkalescence. The growth mechanisms of Bi{sub 2}WO{sub 6} and Bi{sub 3.84}W{sub 0.16}O{sub 6.24} were attributed to the different solubility of WO{sub 4}{sup 2-} and [Bi{sub 2}O{sub 2}]{sup 2+} in precursor suspensions with various pH. For the decomposition of Rhodamine B (RhB) under visible light irradiation ({lambda}>400 nm), different morphology of Bi{sub 2}WO{sub 6} crystal samples obtained by microwavesolvothermal process showed different photocatalytic activity. - Graphical abstract: The morphology modulation of bismuth tungsten oxide nanocrystals synthesized by microwave hydrothermal method with precursor suspension's pH varied from 0.25 (strong acid) to 10.05 (base) was studied. The 3D flower like aggregation of Bi{sub 2}WO{sub 6} nanoflakes and nanooctahedron crystals of Bi{sub 3.84}W{sub 0.16}O{sub 6.24} were prepared. The growth mechanisms of Bi{sub 2}WO{sub 6} and Bi{sub 3.84}W{sub 0.16}O{sub 6.24} were attributed to the different precipitation ability and solubility of H{sub 2}WO{sub 4} and Bi(OH){sub 3} in precursor suspensions with various pH. The photocatalytic evaluation, via the decomposition of Rhodamine B (RhB) under visible light irradiation ({lambda}>420 nm), reveals that nanocrystalline Bi{sub 2}WO{sub 6} samples obtained in different condition exhibit different photocatalytic activities which depend on pH value of the precursor suspensions.

  4. Electrical properties of vanadium tungsten oxide thin films

    SciTech Connect

    Nam, Sung-Pill; Noh, Hyun-Ji; Lee, Sung-Gap; Lee, Young-Hie

    2010-03-15

    The vanadium tungsten oxide thin films deposited on Pt/Ti/SiO{sub 2}/Si substrates by RF sputtering exhibited good TCR and dielectric properties. The dependence of crystallization and electrical properties are related to the grain size of V{sub 1.85}W{sub 0.15}O{sub 5} thin films with different annealing temperatures. It was found that the dielectric properties and TCR properties of V{sub 1.85}W{sub 0.15}O{sub 5} thin films were strongly dependent upon the annealing temperature. The dielectric constants of the V{sub 1.85}W{sub 0.15}O{sub 5} thin films annealed at 400 {sup o}C were 44, with a dielectric loss of 0.83%. The TCR values of the V{sub 1.85}W{sub 0.15}O{sub 5} thin films annealed at 400 {sup o}C were about -3.45%/K.

  5. Activation Energy of Tantalum-Tungsten Oxide Thermite Reaction

    SciTech Connect

    Cervantes, O; Kuntz, J; Gash, A; Munir, Z

    2010-02-25

    The activation energy of a high melting temperature sol-gel (SG) derived tantalum-tungsten oxide thermite composite was determined using the Kissinger isoconversion method. The SG derived powder was consolidated using the High Pressure Spark Plasma Sintering (HPSPS) technique to 300 and 400 C to produce pellets with dimensions of 5 mm diameter by 1.5 mm height. A custom built ignition setup was developed to measure ignition temperatures at high heating rates (500-2000 C {center_dot} min{sup -1}). Such heating rates were required in order to ignite the thermite composite. Unlike the 400 C samples, results show that the samples consolidated to 300 C undergo an abrupt change in temperature response prior to ignition. This change in temperature response has been attributed to the crystallization of the amorphous WO{sub 3} in the SG derived Ta-WO{sub 3} thermite composite and not to a pre-ignition reaction between the constituents. Ignition temperatures for the Ta-WO{sub 3} thermite ranged from approximately 465-670 C. The activation energy of the SG derived Ta-WO{sup 3} thermite composite consolidated to 300 and 400 C were determined to be 37.787 {+-} 1.58 kJ {center_dot} mol{sup -1} and 57.381 {+-} 2.26 kJ {center_dot} mol{sup -1}, respectively.

  6. Strontium adsorption on tantalum-doped hexagonal tungsten oxide.

    PubMed

    Li, Xingliang; Mu, Wanjun; Xie, Xiang; Liu, Bijun; Tang, Hui; Zhou, Guanhong; Wei, Hongyuan; Jian, Yuan; Luo, Shunzhong

    2014-01-15

    Hexagonal tungsten oxide (hex-WO3) has the potential to separate (137)Cs and (90)Sr from nuclear power plant or fission (99)Mo production waste. This study aims to increase the capacity of hex-WO3 to adsorb Sr(2+). Ta-doped hex-WO3 was synthesized by the hydrothermal treatment of sodium tungstate dihydrate and tantalum chloride in concentrated HCl, in the presence of ammonium sulfate. Incorporating Ta into the WO3 framework caused the interlayer spacing to expand, and the band gap to shift to higher energy. The Sr(2+) adsorption capacity of Ta-doped hex-WO3 was significantly higher than that of hex-WO3. Sr(2+) adsorption reached equilibrium within 2h in acidic solution. Maximum Sr(2+) removal occurred at pH 4. Sr(2+) uptake by hex-WO3 was described better by the Freundlich model than by the Langmuir model. Sr(2+) adsorption on hex-WO3 was spontaneous under the studied conditions.

  7. Growth study and photocatalytic properties of Co-doped tungsten oxide mesocrystals

    SciTech Connect

    Sun, Shibin; Chang, Xueting; Li, Zhenjiang

    2012-11-15

    Cobalt-doped tungsten oxide mesocrystals with different morphologies have been successfully generated using a solvothermal method with tungsten hexachloride and cobalt chloride salts as precursors. The resulting mesocrystals were characterized by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, Brunauer-Emmet-Teller analysis of nitrogen sorptometer, and UV-vis diffuse reflectance spectroscopy. The photocatalytic properties of the cobalt-doped tungsten oxide mesocrystals were evaluated on the basis of their ability to degrade methyl orange in an aqueous solution under simulated sunlight irradiation. Results showed that the cobalt doping had obvious effect on the morphologies of the final products, and lenticular and blocky cobalt-doped tungsten oxide mesocrystals could be obtained with 1.0 wt.% and 2.0 wt.% cobalt doping, respectively. The cobalt-doped tungsten oxides exhibited superior photocatalytic activities to that of the undoped tungsten oxide. - Graphical abstract: Schematic illustrations of the growth of the bundled nanowires, lenticular mesocrystals, and blocky mesocrystals. Highlights: Black-Right-Pointing-Pointer Co-doped W{sub 18}O{sub 49} mesocrystals were synthesized using a solvothermal method. Black-Right-Pointing-Pointer The Co doping has obvious effect on the morphology of the final mesocrystals. Black-Right-Pointing-Pointer The Co-doped W{sub 18}O{sub 49} exhibited superior photocatalytic activity to the undoped W{sub 18}O{sub 49}.

  8. The catalyst-free synthesis of large-area tungsten oxide nanowire arrays on ITO substrate and field emission properties

    SciTech Connect

    Huang Kai; Pan Qingtao; Yang Feng; Ni Shibi; He Deyan

    2008-04-01

    Tungsten oxide nanowire arrays have been grown on indium tin oxide coated glass substrate using tungsten trioxide powders as source by thermal evaporation approach without any catalysts. When the O{sub 2}/Ar flow rate ratio was 1/100, large-scale, high-density and uniformly distributed tungsten oxide nanowire arrays were obtained. The morphology and structure properties of the tungsten oxide nanowires were characterized by scanning electron microscopy, X-ray diffraction, and transmission electron microscopy. The influences of the oxygen concentration on the growth, density, shape and structure of the nanowires were investigated. The possible growth mechanism which governs the various types of nanowire arrays as the O{sub 2}/Ar flow rate ratios changed is also discussed. Field emission properties of tungsten oxide nanowire arrays were studied at a poor vacuum condition. The remarkable performance reveals that the tungsten oxide nanowire arrays can be served as a good candidate for commercial application as electron emitters.

  9. Targeting multiple types of tumors using NKG2D-coated iron oxide nanoparticles.

    PubMed

    Wu, Ming-Ru; Cook, W James; Zhang, Tong; Sentman, Charles L

    2014-11-28

    Iron oxide nanoparticles (IONPs) hold great potential for cancer therapy. Actively targeting IONPs to tumor cells can further increase therapeutic efficacy and decrease off-target side effects. To target tumor cells, a natural killer (NK) cell activating receptor, NKG2D, was utilized to develop pan-tumor targeting IONPs. NKG2D ligands are expressed on many tumor types and its ligands are not found on most normal tissues under steady state conditions. The data showed that mouse and human fragment crystallizable (Fc)-fusion NKG2D (Fc-NKG2D) coated IONPs (NKG2D/NPs) can target multiple NKG2D ligand positive tumor types in vitro in a dose dependent manner by magnetic cell sorting. Tumor targeting effect was robust even under a very low tumor cell to normal cell ratio and targeting efficiency correlated with NKG2D ligand expression level on tumor cells. Furthermore, the magnetic separation platform utilized to test NKG2D/NP specificity has the potential to be developed into high throughput screening strategies to identify ideal fusion proteins or antibodies for targeting IONPs. In conclusion, NKG2D/NPs can be used to target multiple tumor types and magnetic separation platform can facilitate the proof-of-concept phase of tumor targeting IONP development.

  10. Genetic polymorphisms of CYP2D6 oxidation in patients with systemic lupus erythematosus

    PubMed Central

    Skrętkowicz, Jadwiga; Barańska, Małgorzata; Kaczorowska, Anna; Rychlik-Sych, Mariola

    2011-01-01

    Introduction Systemic lupus erythematosus (SLE) is a complex, multifactor autoimmune disease. The studies on aetiopathogenesis of autoimmune diseases focus on the impact the genetically conditioned impairment of xenobiotic metabolism may exert. The knowledge of oxidation polymorphism in the course of SLE may be helpful in choosing more efficient and safer therapy. We determined whether there was an association between susceptibility to SLE and particularly to CYP2D6 genotypes. Material and methods The study was carried out in 60 patients with SLE and 129 healthy volunteers and all the subjects were of Polish origin. The samples were analysed for two major defective alles for CYP2D6 – CYP2D6*3 and CYP2D6*4 and one wild -type allele CYP2D6*1-by the polymerase chain reaction fragment length polymorphism (PCR-RFLP) metod with DNA extracted from peripheral blood. Results No statistically significant differences in the incidence of CYP2D6 genotypes between the studied groups were found (p = 0.615). Risk (OR) of SLE development was 1.03 for the carriers of CYP2D6*3 allele and 1.48 for the subjects with CYP2D6*4 allele; but it was not statistically significant. Conclusions Increased occurrence of mutant alleles of the CYP2D6 gene in SLE patients and the calculated OR values could suggest the effect of these mutations on increased SLE development. PMID:22291833

  11. Work Function Modification of Tungsten-Doped Indium Oxides Deposited by the Co-Sputtering Method.

    PubMed

    Oh, Gyujin; Jeon, Jia; Lee, Kyoung Su; Kim, Eun Kyu

    2016-05-01

    We have studied the work function modification of tungsten-doped indium oxides (IWOs) through the co-sputtering of indium oxide (In2O3) and indium tungsten oxide (In2O3 80 wt% + WO3 20 wt%) via a radio frequency (RF) magnetron sputtering system. By controlling the elemental deposition of IWOs, the resultant work functions varied from 4.37 eV to 4.1 eV. The IWO thin films showed excellent properties for application as transparent conducting oxide materials in the region of 0 to 2.43 at.% of tungsten versus the total metal content. The carrier concentration of n-type IWO thin films varied from 8.39 x 10(19) cm(-3) to 8.58 x 10(21) cm(-3), while the resistivity varied from 3.15 x 10(-4) Ωcm to 2.26 x 10(-3) Ωcm. The largest measured optical band gap was 3.82 eV determined at 2.43 at.% of tungsten atoms relative to the total amount of metal atoms, while the smallest optical band gap was 3.6 eV at 4.78 at.% of tungsten. IWO films containing more than 2.43 at.% of tungsten atoms relative to the total number of metal atoms revealed an average transmittance of over 80% within the visible light region.

  12. Work Function Modification of Tungsten-Doped Indium Oxides Deposited by the Co-Sputtering Method.

    PubMed

    Oh, Gyujin; Jeon, Jia; Lee, Kyoung Su; Kim, Eun Kyu

    2016-05-01

    We have studied the work function modification of tungsten-doped indium oxides (IWOs) through the co-sputtering of indium oxide (In2O3) and indium tungsten oxide (In2O3 80 wt% + WO3 20 wt%) via a radio frequency (RF) magnetron sputtering system. By controlling the elemental deposition of IWOs, the resultant work functions varied from 4.37 eV to 4.1 eV. The IWO thin films showed excellent properties for application as transparent conducting oxide materials in the region of 0 to 2.43 at.% of tungsten versus the total metal content. The carrier concentration of n-type IWO thin films varied from 8.39 x 10(19) cm(-3) to 8.58 x 10(21) cm(-3), while the resistivity varied from 3.15 x 10(-4) Ωcm to 2.26 x 10(-3) Ωcm. The largest measured optical band gap was 3.82 eV determined at 2.43 at.% of tungsten atoms relative to the total amount of metal atoms, while the smallest optical band gap was 3.6 eV at 4.78 at.% of tungsten. IWO films containing more than 2.43 at.% of tungsten atoms relative to the total number of metal atoms revealed an average transmittance of over 80% within the visible light region. PMID:27483882

  13. Study on the oxidation and reduction of tungsten surface for sub-50 nm patterning process

    SciTech Connect

    Kim, Jong Kyu; Nam, Seok Woo; Cho, Sung Il; Jhon, Myung S.; Min, Kyung Suk; Kim, Chan Kyu; Jung, Ho Bum; Yeom, Geun Young

    2012-11-15

    The oxidation characteristics of tungsten line pattern during the carbon-based mask-layer removal process using oxygen plasmas have been investigated for sub-50 nm patterning processes, in addition to the reduction characteristics of the WO{sub x} layer formed on the tungsten line surface using hydrogen plasmas. The surface oxidation of tungsten lines during the mask layer removal process could be minimized by using low-temperature (300 K) plasma processing for the removal of the carbon-based material. Using this technique, the thickness of WO{sub x} on the tungsten line could be decreased to 25% compared to results from high-temperature processing. The WO{sub x} layer could also be completely removed at a low temperature of 300 K using a hydrogen plasma by supplying bias power to the tungsten substrate to provide a activation energy for the reduction. When this oxidation and reduction technique was applied to actual 40-nm-CD device processing, the complete removal of WO{sub x} formed on the sidewall of tungsten line could be observed.

  14. Synthesis and optical properties of Au decorated colloidal tungsten oxide nanoparticles

    NASA Astrophysics Data System (ADS)

    Tahmasebi, Nemat; Mahdavi, Seyed Mohammad

    2015-11-01

    In this study, colloidal tungsten oxide nanoparticles were fabricated by pulsed laser ablation of tungsten target using the first harmonic of a Nd:YAG laser (1064 nm) in deionized water. After ablation, a 0.33 g/lit HAuCl4 aqueous solution was added into as-prepared colloidal nanoparticles. In this process, Au3+ ions were reduced to decorate gold metallic state (Au0) onto colloidal tungsten oxide nanoparticles surface. The morphology and chemical composition of the synthesized nanoparticles were studied by AFM, XRD, TEM and XPS techniques. UV-Vis analysis reveals a distinct absorption peak at ∼530 nm. This peak can be attributed to the surface plasmon resonance (SPR) of Au and confirms formation of gold state. Moreover, X-ray photoelectron spectroscopy reveals that Au ions' reduction happens after adding HAuCl4 solution into as-prepared colloidal tungsten oxide nanoparticles. Transmission electron microscope shows that an Au shell has been decorated onto colloidal WO3 nanoparticles. Noble metal decorated tungsten oxide nanostructure could be an excellent candidate for photocatalysis, gas sensing and gasochromic applications. Finally, the gasochromic behavior of the synthesized samples was investigated by H2 and O2 gases bubbling into the produced colloidal Au/WO3 nanoparticles. Synthesized colloidal nanoparticles show excellent coloration contrast (∼80%) through NIR spectra.

  15. Preparation of silicate tungsten bronzes on aluminum by plasma electrolytic oxidation process in 12-tungstosilicic acid

    NASA Astrophysics Data System (ADS)

    Petković, M.; Stojadinović, S.; Vasilić, R.; Belča, I.; Nedić, Z.; Kasalica, B.; Mioč, U. B.

    2011-09-01

    The growth of silicate tungsten bronzes on aluminum by plasma electrolytic oxidation in 12-tungstosilicic acid is experimentally investigated and discussed. Real time imaging and optical emission spectroscopy characterization of plasma electrolytic oxidation show that spatial density of microdischarges is the highest in the early stage of the process, while the percentage of oxide coating area covered by active discharge sites decreases slowly with time. Emission spectrum of microdischarges has several intensive band peaks originating either from aluminum electrode or from the electrolyte. Surface roughness of obtained oxide coatings increases with prolonged time of plasma electrolytic oxidation, as their microhardness decreases. Raman spectroscopy and energy dispersive X-ray spectroscopy are employed to confirm that the outer layer of oxide coatings formed during the plasma electrolytic oxidation process is silicate tungsten bronze

  16. Surface studies of barium and barium oxide on tungsten and its application to understanding the mechanism of operation of an impregnated tungsten cathode

    NASA Technical Reports Server (NTRS)

    Forman, R.

    1976-01-01

    Surface studies have been made of multilayer and monolayer films of barium and barium oxide on a tungsten substrate. The purpose of the investigation was to synthesize the surface conditions that exist on an activated impregnated tungsten cathode and obtain a better understanding of the mechanism of operation of such cathodes. The techniques employed in these measurements were Auger spectroscopy and work-function measurements. The results of this study show that the surface of an impregnated cathode is identical to that observed for a synthesized monolayer or partial monolayer of barium on oxidized tungsten by evaluating Auger spectra and work-function measurements. Data obtained from desorption studies of barium monolayers on a tungsten substrate in conjunction with Auger and work-function results have been interpreted to show that throughout most of its life an impreganated cathode has a partial monolayer, rather than a monolayer, of barium on its surface.

  17. Effect of silver incorporation in phase formation and band gap tuning of tungsten oxide thin films

    SciTech Connect

    Jolly Bose, R.; Kumar, R. Vinod; Sudheer, S. K.; Mahadevan Pillai, V. P.; Reddy, V. R.; Ganesan, V.

    2012-12-01

    Silver incorporated tungsten oxide thin films are prepared by RF magnetron sputtering technique. The effect of silver incorporation in micro structure evolution, phase enhancement, band gap tuning and other optical properties are investigated using techniques such as x-ray diffraction, micro-Raman spectroscopy, atomic force microscopy, scanning electron microscopy, energy dispersive x-ray spectroscopy, and UV-Visible spectroscopy. Effect of silver addition in phase formation and band gap tuning of tungsten oxide thin films are investigated. It is found that the texturing and phase formation improves with enhancement in silver content. It is also found that as the silver incorporation enhances the thickness of the films increases at the same time the strain in the film decreases. Even without annealing the desired phase can be achieved by doping with silver. A broad band centered at the wavelength 437 nm is observed in the absorption spectra of tungsten oxide films of higher silver incorporation and this can be attributed to surface plasmon resonance of silver atoms present in the tungsten oxide matrix. The transmittance of the films is decreased with increase in silver content which can be due to increase in film thickness, enhancement of scattering, and absorption of light caused by the increase of grain size, surface roughness and porosity of films and enhanced absorption due to surface plasmon resonance of silver. It is found that silver can act as the seed for the growth of tungsten oxide grains and found that the grain size increases with silver content which in turn decreases the band gap of tungsten oxide from 3.14 eV to 2.70 eV.

  18. Oxidation and Volatilization from Tungsten Brush High Heat Flux Armor During High Temperature Steam Exposure

    SciTech Connect

    Smolik, Galen Richard; Pawelko, Robert James; Anderl, Robert Andrew; Petti, David Andrew

    2000-05-01

    Tungsten brush accommodates thermal stresses and high heat flux in fusion reactor components such as plasma facing surfaces or armor. However, inherently higher surface areas are introduced with the brush design. We have tested a specific design of tungsten brush in steam between 500 and 1100°C. Hydrogen generation and tungsten volatilization rates were determined to address fusion safety issues. The brush prepared from 3.2-mm diameter welding rods had a packing density of 85 percent. We found that both hydrogen generation and tungsten volatilization from brush, fixtured to represent a unit within a larger component, were less than projections based upon the total integrated surface area (TSA). Steam access and the escape of hydrogen and volatile oxide from void spaces within the brush are restricted compared to specimens with more direct diffusion pathways to the test environment. Hydrogen generation rates from restrained specimens based on normal surface area (NSA) remain about five times higher than rates based on total surface areas from specimens with direct steam access. Volatilization rates from restrained specimens based upon normal surface area (NSA) were only 50 percent higher than our historic cumulative maximum flux plot (CMFP) for tungsten. This study has shown that hydrogen generation and tungsten volatilization from brush do not scale according to predictions with previously determined rates, but in fact, with higher packing density could approach those from flat surfaces.

  19. 2 D patterns of soil gas diffusivity , soil respiration, and methane oxidation in a soil profile

    NASA Astrophysics Data System (ADS)

    Maier, Martin; Schack-Kirchner, Helmer; Lang, Friederike

    2015-04-01

    The apparent gas diffusion coefficient in soil (DS) is an important parameter describing soil aeration, which makes it a key parameter for root growth and gas production and consumption. Horizontal homogeneity in soil profiles is assumed in most studies for soil properties - including DS. This assumption, however, is not valid, even in apparently homogeneous soils, as we know from studies using destructive sampling methods. Using destructive methods may allow catching a glimpse, but a large uncertainty remains, since locations between the sampling positions cannot be analyzed, and measurements cannot be repeated. We developed a new method to determine in situ the apparent soil gas diffusion coefficient in order to examine 2 D pattern of DS and methane oxidation in a soil profile. Different tracer gases (SF6, CF4, C2H6) were injected continuously into the subsoil and measured at several locations in the soil profile. These data allow for modelling inversely the 2 D patterns of DS using Finite Element Modeling. The 2D DS patterns were then combined with naturally occurring CH4 and CO2 concentrations sampled at the same locations to derive the 2D pattern of soil respiration and methane oxidation in the soil profile. We show that methane oxidation and soil respiration zones shift within the soil profile while the gas fluxes at the surface remain rather stable during a the 3 week campaign.

  20. Generation and characterization of nano tungsten oxide particles by wire explosion process

    SciTech Connect

    Aravinth, S.; Sankar, Binu; Chakravarthi, S.R.; Sarathi, R.

    2011-02-15

    Nano tungsten oxide particles are produced by wire explosion process. It is realized that by exploding tungsten conductor in lower pressure of oxygen, unreacted phase of tungsten was present and it could be reduced by increasing the operating pressure and increasing the amount of energy deposited to the exploding conductor. It is realized that the nucleation rate of the particle could be high only at the point of maximum saturation ratio, irrespective of the pressure of the oxygen. The size of the critical nucleus formed is low when the saturation ratio and the nucleation rate are at maximum. The nano metal oxide particle formation by wire explosion process allows one to conclude that the second stage annealing process has a major impact on the final grain size formed. The high speed camera photographs of wire explosion process were used to understand the dynamics of particle formation by wire explosion process. The Transmission Electron Microscopy (TEM) analysis indicates that the nano tungsten oxide (WO{sub 3}) particles are of spherical shape and the analysis of particle size indicates that it follows log normal distribution. - Graphical Abstract: Nano tungsten oxide (WO{sub 3}) particles are produced by wire explosion process. Theoretical analysis indicates that the size of the critical nucleus formed is low when the saturation ratio and the nucleation rate are at maximum. High speed camera photographs of wire explosion process were used to understand the dynamics of particles formed. Research Highlights: {yields}Lower particle size is possible with lower pressure. {yields}Particle size is increased with reduced energy ratio. {yields}Unreacted tungsten content reduces when oxygen pressure increases.

  1. Thin Film Optical Coatings of Vanadium Oxide and Mixed Tungsten/Vanadium Oxide Deposited by APCVD Employing Precursors of Vanadyl Acetylacetonate and a Mixture with Tungsten Hexacarbonyl

    NASA Astrophysics Data System (ADS)

    Bodurov, Georgi; Ivanova, Tatyana; Abrashev, Miroslav; Nenova, Zoya; Gesheva, Kostadinka

    Thin films of transition metals oxides are studied and comparison is made for two types of mixed precursors, first containing only hexacarbonyls, and second containing tungsten hexacarbonyl and vanadyl acetylacetonate (Vanadium (III) acetylacetonate). The best electrochromic material is WO3, although when deposited by Atmospheric Pressure Chemical Vapour Deposition (APCVD) films of WO3 grow very slowly. In production stage, the growth-rate is very important factor for assuring a flow-through process. Our previous investigations showed that addition of a small fraction of lower temperature precursor such as Mo(CO)6, or V(CO)6, to the basic precursor of W(CO)6 result in higher growth rate of films. Our recent studies on mixed WxV1-xO3 showed excellent substrate coverage and high growth-rate. V(CO)6 is a lower thermally stable precursor that allows the first nuclei-islands to be formed on the hot substrates which further facilitate the tungsten oxide film deposition. However V(CO)6 is much too expensive for large-scale production, thus we adopted another compound as precursor - vanadium acetylacetonate, expecting eventual growth-rate increase. The paper describes optical properties of films of vanadium oxide grown in result of utilizing the acetylacetonate. Besides, the paper describes our attempt to deposit mixed films of tungsten/vanadium using a mixed precursor of vanadyl acetylacetonate and tungsten hexacarbonyl. To our knowledge this is a new mixed precursor based on largely used single precursors namely W(CO)6 and Vanadium acetylacetonate. Efforts were needed to adjust the mixed precursor ratio, keeping in mind the vapour pressures of the two chemicals at the deposition temperatures used. The paper presents the results for the visible transmittance and the film material modulation properties, studied by FTIR and Raman spectra. The dependence of the films optical behavior on APCVD process parameters, substrate temperatures, vapour source temperature

  2. Fabrication and multifunctional properties of ultrasmall water-soluble tungsten oxide quantum dots.

    PubMed

    Peng, Huaping; Liu, Pan; Lin, Danwei; Deng, Yani; Lei, Yun; Chen, Wei; Chen, Yuanzhong; Lin, Xinhua; Xia, Xinghua; Liu, Ailin

    2016-07-21

    A facile and green method has been demonstrated to synthesize ultrasmall tungsten oxide quantum dots (WOx QDs). The water-soluble WOx QDs present high luminescence stability, strong peroxidase-like activity, and excellent electrochemiluminescence properties. This work provides an eco-friendly strategy to prepare multifunctional WOx QDs, and opens the door for bioapplications of the WOx QDs. PMID:27381501

  3. Lysozyme-mediated biomineralization of titanium-tungsten oxide hybrid nanoparticles with high photocatalytic activity.

    PubMed

    Kim, Jung Kyu; Jang, Ji-ryang; Choi, Noori; Hong, Dahyun; Nam, Chang-Hoon; Yoo, Pil J; Park, Jong Hyeok; Choe, Woo-Seok

    2014-10-21

    Titanium-tungsten oxide composites with greatly enhanced photocatalytic activity were synthesized by lysozyme-mediated biomineralization. It was shown for the first time that simple control of the onset of biomineralization could enable fine tuning of the composition and crystallinity of the composites to determine their photocatalytic performance.

  4. Physical and chemical properties of tungsten oxide nanoparticles obtained in plasma discharge under ultrasonic action

    NASA Astrophysics Data System (ADS)

    Bulychev, N. A.; Kazaryan, M. A.

    2015-12-01

    In this study, plasma discharge in a liquid at intensive ultrasonic field above the cavitation threshold has been proven to be of great interest for initiation of various physical and chemical processes. In such surcharge, nanoparticles of tungsten oxide with controlled size and shape and narrow particle size distribution have been synthesized. Further exploration of synthesized nanoparticles has demonstrated that the factor of ultrasonic cavitation during the synthesis substantially affects physical and chemical characteristics of nanoparticles. Similar procedure might be effective for compounds of tungsten and rare-earth elements.

  5. Laser-assisted oxidation of multi-layer tungsten diselenide nanosheets

    NASA Astrophysics Data System (ADS)

    Tan, C.; Liu, Y.; Chou, H.; Kim, J.-S.; Wu, D.; Akinwande, D.; Lai, K.

    2016-02-01

    We report the structural and electrical characterization of tungsten oxides formed by illuminating multi-layer tungsten diselenide (WSe2) nanosheets with an intense laser beam in the ambient environment. A noninvasive microwave impedance microscope (MIM) was used to perform electrical imaging of the samples. The local conductivity ˜102 S/m of the oxidized product, measured by the MIM and conventional transport experiments, is much higher than that of the pristine WSe2, suggesting the formation of sub-stoichiometric WO3-x polycrystals with n-type carriers. With further efforts to improve the conductivity of the oxides, the laser-assisted oxidation process may be useful for patterning conductive features on WSe2 or forming electrical contacts to various transition metal dichalcogenides.

  6. Application of diffusion barriers to the refractory fibers of tungsten, columbium, carbon and aluminum oxide

    NASA Technical Reports Server (NTRS)

    Douglas, F. C.; Paradis, E. L.; Veltri, R. D.

    1973-01-01

    A radio frequency powered ion-plating system was used to plate protective layers of refractory oxides and carbide onto high strength fiber substrates. Subsequent overplating of these combinations with nickel and titanium was made to determine the effectiveness of such barrier layers in preventing diffusion of the overcoat metal into the fibers with consequent loss of fiber strength. Four substrates, five coatings, and two metal matrix materials were employed for a total of forty material combinations. The substrates were tungsten, niobium, NASA-Hough carbon, and Tyco sapphire. The diffusion-barrier coatings were aluminum oxide, yttrium oxide, titanium carbide, tungsten carbide with 14% cobalt addition, and zirconium carbide. The metal matrix materials were IN 600 nickel and Ti 6/4 titanium. Adhesion of the coatings to all substrates was good except for the NASA-Hough carbon, where flaking off of the oxide coatings in particular was observed.

  7. Effect of negative bias on the composition and structure of the tungsten oxide thin films deposited by magnetron sputtering

    NASA Astrophysics Data System (ADS)

    Wang, Meihan; Lei, Hao; Wen, Jiaxing; Long, Haibo; Sawada, Yutaka; Hoshi, Yoichi; Uchida, Takayuki; Hou, Zhaoxia

    2015-12-01

    Tungsten oxide thin films were deposited at room temperature under different negative bias voltages (Vb, 0 to -500 V) by DC reactive magnetron sputtering, and then the as-deposited films were annealed at 500 °C in air atmosphere. The crystal structure, surface morphology, chemical composition and transmittance of the tungsten oxide thin films were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS) and UV-vis spectrophotometer. The XRD analysis reveals that the tungsten oxide films deposited at different negative bias voltages present a partly crystallized amorphous structure. All the films transfer from amorphous to crystalline (monoclinic + hexagonal) after annealing 3 h at 500 °C. Furthermore, the crystallized tungsten oxide films show different preferred orientation. The morphology of the tungsten oxide films deposited at different negative bias voltages is consisted of fine nanoscale grains. The grains grow up and conjunct with each other after annealing. The tungsten oxide films deposited at higher negative bias voltages after annealing show non-uniform special morphology. Substoichiometric tungsten oxide films were formed as evidenced by XPS spectra of W4f and O1s. As a result, semi-transparent films were obtained in the visible range for all films deposited at different negative bias voltages.

  8. 2D Hybrid Nanostructure of Reduced Graphene Oxide-CdS Nanosheet for Enhanced Photocatalysis.

    PubMed

    Bera, Rajesh; Kundu, Simanta; Patra, Amitava

    2015-06-24

    Graphene-based hybrid nanostructures have recently emerged as a new class of functional materials for light-energy conversion and storage. Here, we have synthesized reduced graphene oxide (RGO)-semiconductor composites to improve the efficiency of photocatalysis. Zero-dimensional CdS nanoparticles (0D), one-dimensional CdS nanorods (1D), and two-dimensional CdS nanosheets (2D) are grafted on the RGO sheet (2D) by a surface modification method using 4-aminothiophenol (4-ATP). Structural analysis confirms the attachment of CdS nanocrystals with RGO, and the strong electronic interaction is found in the case of a CdS nanosheet and RGO, which has an influence on photocatalytic properties. The degradation of dye under visible light varies with changing the dimension of nanocrystals, and the catalytic activity of the CdS NS/RGO composite is ∼4 times higher than that of CdS nanoparticle/RGO and 3.4 times higher than that of CdS nanorod/RGO composite samples. The catalytic activity of the CdS nanosheet/RGO composite is also found to be ∼2.5 times than that of pure CdS nanosheet samples. The unique 2D-2D nanoarchitecture would be effective to harvest photons from solar light and transport electrons to reaction sites with respect to other 0D-2D and 1D-2D hybrid systems. This observation can be extended to other graphene-based inorganic semiconductor composites, which can provide a valuable opportunity to explore novel hybrid materials with superior visible-light-induced catalytic activity.

  9. 2D/2D nano-hybrids of γ-MnO₂ on reduced graphene oxide for catalytic ozonation and coupling peroxymonosulfate activation.

    PubMed

    Wang, Yuxian; Xie, Yongbing; Sun, Hongqi; Xiao, Jiadong; Cao, Hongbin; Wang, Shaobin

    2016-01-15

    Two-dimensional reduced graphene oxide (2D rGO) was employed as both a shape-directing medium and support to fabricate 2D γ-MnO2/2D rGO nano-hybrids (MnO2/rGO) via a facile hydrothermal route. For the first time, the 2D/2D hybrid materials were used for catalytic ozonation of 4-nitrophenol. The catalytic efficiency of MnO2/rGO was much higher than either MnO2 or rGO only, and rGO was suggested to play the role for promoting electron transfers. Quenching tests using tert-butanol, p-benzoquinone, and sodium azide suggested that the major radicals responsible for 4-nitrophenol degradation and mineralization are O2(-) and (1)O2, but not ·OH. Reusability tests demonstrated a high stability of the materials in catalytic ozonation with minor Mn leaching below 0.5 ppm. Degradation mechanism, reaction kinetics, reusability and a synergistic effect between catalytic ozonation and coupling peroxymonosulfate (PMS) activation were also discussed.

  10. Studies on growth and characterization of heterogeneous tungsten oxide nanostructures for photoelectrochemical and gas sensing applications

    NASA Astrophysics Data System (ADS)

    Senthilkumar, R.; Mahalingam, T.; Ravi, G.

    2016-01-01

    Tungsten oxide nanostructures were developed on indium tin oxide coated glass substrates by modified thermal evaporation process without using catalyst and vacuum. Depending on the substrate temperature and vapor concentration, different nanostructures like rod, sheet and pyramid were formed. Morphology, phase structure and crystallinity of the nanostructure films were characterized by Scanning electron microscope (SEM), X-ray diffraction (XRD), Raman spectroscopy and HR-TEM. The samples were investigated under dark current and photocurrent and in H2SO4 aqueous solution as a function of applied potential. The saturated photocurrent density of tungsten oxide was found to be ≈14.4 μA cm-2. The films were also investigated as resistive gas sensor for ethanol gases (10-50 ppm) at room temperature. The response and recovery time were also determined.

  11. Combined flame and electrodeposition synthesis of energetic coaxial tungsten-oxide/aluminum nanowire arrays.

    PubMed

    Dong, Zhizhong; Al-Sharab, Jafar F; Kear, Bernard H; Tse, Stephen D

    2013-09-11

    A nanostructured thermite composite comprising an array of tungsten-oxide (WO2.9) nanowires (diameters of 20-50 nm and lengths of >10 μm) coated with single-crystal aluminum (thickness of ~16 nm) has been fabricated. The method involves combined flame synthesis of tungsten-oxide nanowires and ionic-liquid electrodeposition of aluminum. The geometry not only presents an avenue to tailor heat-release characteristics due to anisotropic arrangement of fuel and oxidizer but also eliminates or minimizes the presence of an interfacial Al2O3 passivation layer. Upon ignition, the energetic nanocomposite exhibits strong exothermicity, thereby being useful for fundamental study of aluminothermic reactions as well as enhancing combustion characteristics.

  12. Synthesis, Characterization, and Catalytic Function of Novel Highly Dispersed Tungsten Oxide Catalysts on Mesoporous Silica

    SciTech Connect

    Herrera, Jose E.; Kwak, Ja Hun; Hu, Jian Zhi; Wang, Yong; Peden, Charles HF; Macht, Josef; Iglesia, Enrique

    2006-04-01

    The physical and chemical properties of tungsten oxide supported on SBA-15 mesoporous silica prepared by a controlled grafting process through atomic layer deposition (ALD) were studied using complementary characterization methods. X-ray diffraction, optical absorption and transmission electron microscopy showed that tungsten oxide species are highly dispersed on SBA-15 surfaces, even at 30 wt.% WOx contents (surface density: 1.33 WOx/nm2). ALD methods led to samples with much better thermal stability than those prepared via impregnation. Dehydration reactions of 2-butanol and methanol dehydration were used as probe reactions. Differences in reaction rates between the samples prepared by ALD and conventional impregnation reflect the sintering resistance of catalysts prepared by ALD. Notably, temperature programmed oxidation of spent catalysts showed that carbon formation was not responsible for the different dehydration rates in samples prepared by ALD and impregnation..

  13. Laser Desorption Ionization of small molecules assisted by Tungsten oxide and Rhenium oxide particles

    PubMed Central

    Bernier, Matthew; Wysocki, Vicki; Dagan, Shai

    2015-01-01

    Inorganic metal oxides have shown potential as matrices for assisting in laser desorption ionization (LDI) with advantages over the aromatic acids typically used. Rhenium and tungsten oxides are an attractive option due to their high work functions and relative chemical inertness. In this work, it is shown that ReO3 and WO3, in microparticle (μP) powder forms, can efficiently ionize various types of small molecules and provide minimized background contamination at analyte concentrations below 1 ng/μL. This study shows that untreated inorganic WO3 and ReO3 particles are valid matrix options for detection of protonatable, radical, and precharged species under LDI. Qualitatively, the WO3 μP showed an improved detection of apigenin, sodiated glucose, and the precharged analyte choline, while the ReO3 μP allowed detection of protonated cocaine, quinuclidine, ametryn, and radical ions of polyaromatic hydrocarbons at detection levels as low as 50 pg/μL. For thermometer ion survival yield experiments, it was also shown that the ReO3 powder was significantly softer than CCA. Furthermore, it provided higher intensities of cocaine and polyaromatic hydrocarbons, at laser flux values equal to that used with CCA. PMID:26349643

  14. Tungsten oxide-Au nanosized film composites for glucose oxidation and sensing in neutral medium

    PubMed Central

    Gougis, Maxime; Ma, Dongling; Mohamedi, Mohamed

    2015-01-01

    In this work, we report for the first time the use of tungsten oxide (WOx) as catalyst support for Au toward the direct electrooxidation of glucose. The nanostructured WOx/Au electrodes were synthesized by means of laser-ablation technique. Both micro-Raman spectroscopy and transmission electron microscopy showed that the produced WOx thin film is amorphous and made of ultrafine particles of subnanometer size. X-ray diffraction and X-ray photoelectron spectroscopy revealed that only metallic Au was present at the surface of the WOx/Au composite, suggesting that the WOx support did not alter the electronic structure of Au. The direct electrocatalytic oxidation of glucose in neutral medium such as phosphate buffered saline (pH 7.2) solution has been investigated with cyclic voltammetry, chronoamperometry, and square-wave voltammetry. Sensitivity as high as 65.7 μA cm−2 mM−1 up to 10 mM of glucose and a low detection limit of 10 μM were obtained with square-wave voltammetry. This interesting analytical performance makes the laser-fabricated WOx/Au electrode potentially promising for implantable glucose fuel cells and biomedical analysis as the evaluation of glucose concentration in biological fluids. Finally, owing to its unique capabilities proven in this work, it is anticipated that the laser-ablation technique will develop as a fabrication tool for chip miniature-sized sensors in the near future. PMID:25931820

  15. Tungsten oxide-Au nanosized film composites for glucose oxidation and sensing in neutral medium.

    PubMed

    Gougis, Maxime; Ma, Dongling; Mohamedi, Mohamed

    2015-01-01

    In this work, we report for the first time the use of tungsten oxide (WOx) as catalyst support for Au toward the direct electrooxidation of glucose. The nanostructured WOx/Au electrodes were synthesized by means of laser-ablation technique. Both micro-Raman spectroscopy and transmission electron microscopy showed that the produced WOx thin film is amorphous and made of ultrafine particles of subnanometer size. X-ray diffraction and X-ray photoelectron spectroscopy revealed that only metallic Au was present at the surface of the WOx/Au composite, suggesting that the WOx support did not alter the electronic structure of Au. The direct electrocatalytic oxidation of glucose in neutral medium such as phosphate buffered saline (pH 7.2) solution has been investigated with cyclic voltammetry, chronoamperometry, and square-wave voltammetry. Sensitivity as high as 65.7 μA cm(-2) mM(-1) up to 10 mM of glucose and a low detection limit of 10 μM were obtained with square-wave voltammetry. This interesting analytical performance makes the laser-fabricated WOx/Au electrode potentially promising for implantable glucose fuel cells and biomedical analysis as the evaluation of glucose concentration in biological fluids. Finally, owing to its unique capabilities proven in this work, it is anticipated that the laser-ablation technique will develop as a fabrication tool for chip miniature-sized sensors in the near future.

  16. Laser desorption ionization of small molecules assisted by tungsten oxide and rhenium oxide particles.

    PubMed

    Bernier, Matthew C; Wysocki, Vicki H; Dagan, Shai

    2015-07-01

    Inorganic metal oxides have shown potential as matrices for assisting in laser desorption ionization with advantages over the aromatic acids typically used. Rhenium and tungsten oxides are attractive options due to their high work functions and relative chemical inertness. In this work, it is shown that ReO3 and WO3 , in microparticle (μP) powder forms, can efficiently facilitate ionization of various types of small molecules and provide minimized background contamination at analyte concentrations below 1 ng/µL. This study shows that untreated inorganic WO3 and ReO3 particles are valid matrix options for detection of protonatable, radical, and precharged species under laser desorption ionization. Qualitatively, the WO3 μP showed improved detection of apigenin, sodiated glucose, and precharged analyte choline, while the ReO3 μP allowed better detection of protonated cocaine, quinuclidine, ametryn, and radical ions of polyaromatic hydrocarbons at detection levels as low as 50 pg/µL. For thermometer ion survival yield experiments, it was also shown that the ReO3 powder was significantly softer than α-cyano-4-hydroxycinnaminic acid. Furthermore, it provided higher intensities of cocaine and polyaromatic hydrocarbons, at laser flux values equal to those used with α-cyano-4-hydroxycinnaminic acid.

  17. Direct laser deposition of nanostructured tungsten oxide for sensing applications

    NASA Astrophysics Data System (ADS)

    Palla-Papavlu, Alexandra; Filipescu, Mihaela; Schneider, Christof W.; Antohe, Stefan; Ossi, Paolo M.; Radnóczi, György; Dinescu, Maria; Wokaun, Alexander; Lippert, Thomas

    2016-05-01

    Nanostructured tungsten trioxide (WO3) thin films are deposited by pulsed laser deposition (PLD) and radio-frequency (RF) assisted PLD onto interdigitated sensor structures. Structural characterization by x-ray diffraction and Raman spectroscopy shows the WO3 films are polycrystalline, with a pure monoclinic phase for the PLD grown films. The as-fabricated WO3 sensors are tested for ammonia (NH3) detection, by measuring the electrical response to NH3 at different temperatures. Sensors based on WO3 deposited by RF-PLD do not show any response to NH3. In contrast, sensors fabricated by PLD operating at 100 °C and 200 °C show a slow recovery time whilst at 300 °C, these sensors are highly sensitive in the low ppm range with a recovery time in the range of a few seconds. The microstructure of the films is suggested to explain their excellent electrical response. Columnar WO3 thin films are obtained by both deposition methods. However, the WO3 films grown by PLD are porous, (which may allow NH3 molecules to diffuse through the film) whereas RF-PLD films are dense. Our results highlight that WO3 thin films deposited by PLD can be applied for the fabrication of gas sensors with a performance level required for industrial applications.

  18. Blue Phosphorene Oxide: Strain-Tunable Quantum Phase Transitions and Novel 2D Emergent Fermions

    NASA Astrophysics Data System (ADS)

    Zhu, Liyan; Wang, Shan-Shan; Guan, Shan; Liu, Ying; Zhang, Tingting; Chen, Guibin; Yang, Shengyuan A.

    2016-10-01

    Tunable quantum phase transitions and novel emergent fermions in solid state materials are fascinating subjects of research. Here, we propose a new stable two-dimensional (2D) material, the blue phosphorene oxide (BPO), which exhibits both. Based on first-principles calculations, we show that its equilibrium state is a narrow-bandgap semiconductor with three bands at low energy. Remarkably, a moderate strain can drive a semiconductor-to-semimetal quantum phase transition in BPO. At the critical transition point, the three bands cross at a single point at Fermi level, around which the quasiparticles are a novel type of 2D pseudospin-1 fermions. Going beyond the transition, the system becomes a symmetry-protected semimetal, for which the conduction and valence bands touch quadratically at a single Fermi point that is protected by symmetry, and the low-energy quasiparticles become another novel type of 2D double Weyl fermions. We construct effective models characterizing the phase transition and these novel emergent fermions, and we point out several exotic effects, including super Klein tunneling, supercollimation, and universal optical absorbance. Our result reveals BPO as an intriguing platform for the exploration of fundamental properties of quantum phase transitions and novel emergent fermions, and also suggests its great potential in nanoscale device applications.

  19. Tungsten-doped tin oxide thin films prepared by pulsed plasma deposition

    SciTech Connect

    Huang Yanwei; Zhang Qun Li Guifeng; Yang Ming

    2009-05-15

    Transparent conductive oxide tungsten-doped tin oxide thin films were deposited on glass substrates from ceramic targets by the pulsed plasma deposition method. The structural, electrical and optical properties have been investigated as functions of tungsten doping content and oxygen partial pressure. The lowest resistivity of 2.1 x 10{sup -3} {omega}{center_dot}cm was reproducibly obtained, with carrier mobility of 30 cm{sup 2}V{sup -1}s{sup -1} and carrier concentration of 9.6 x 10{sup 19} cm{sup -3} at the oxygen partial pressure of 1.8 Pa. The average optical transmission was in excess of 80% in the visible region from 400 to 700 nm, with the optical band gap ranging from 3.91 to 4.02 eV.

  20. Synthesis, consolidation and characterization of sol-gel derived tantalum-tungsten oxide thermite composites

    NASA Astrophysics Data System (ADS)

    Cervantes, Octavio

    Energetic composite powders consisting of sol-gel (SG) derived nanostructured tungsten oxide were produced with various amounts of micrometer-scale tantalum fuel metal. Such energetic composite powders were ignition-tested and results show that the powders are not sensitive to friction, spark and/or impact ignition. Initial consolidation experiments, using the High Pressure Spark Plasma Sintering (HPSPS) technique, on the SG derived nanostructured tungsten oxide produced samples with higher relative density than can be achieved with commercially available tungsten oxide. The SG derived nanostructured tungsten oxide with immobilized tantalum fuel metal (Ta - WO3) energetic composite was consolidated to a density of 9.17 g·cm-3 or 93% relative density. In addition, those samples were consolidated without significant pre-reaction of the constituents, thus retaining their stored chemical energy. The heat of combustion of two distinctly synthesized stoichiometric tantalum-tungsten oxide energetic composites was investigated by bomb calorimetry. One composite was synthesized using a sol-gel (SG) derived method in which micrometric-scale tantalum is immobilized in a tungsten oxide three-dimensional nanostructured network structure. The second energetic composite was made from the mixing of micrometric-scale tantalum and commercially available (CA) nanometric tungsten oxide powders. The energetic composites were consolidated using the spark plasma sintering (SPS) technique under a 300 MPa pressure and at temperatures of 25, 400, and 500°C. For samples consolidated at 25°C, the density of the CA composite is 61.65 +/- 1.07% in comparison to 56.41 +/- 1.19% for the SG derived composite. In contrast, the resulting densities of the SG composite are higher than the CA composite for samples consolidated at 400 and 500°C. The theoretical maximum density for the SG composite consolidated to 400 and 500°C are 81.30 +/- 0.58% and 84.42 +/- 0.62%, respectively. The theoretical

  1. ANME-2D Archaea Catalyze Methane Oxidation in Deep Subsurface Sediments Independent of Nitrate Reduction

    NASA Astrophysics Data System (ADS)

    Hernsdorf, A. W.; Amano, Y.; Suzuki, Y.; Ise, K.; Thomas, B. C.; Banfield, J. F.

    2015-12-01

    Terrestrial sediments are an important global reservoir for methane. Microorganisms in the deep subsurface play a critical role in the methane cycle, yet much remains to be learned about their diversity and metabolisms. To provide more comprehensive insight into the microbiology of the methane cycle in the deep subsurface, we conducted a genome-resolved study of samples collected from the Horonobe Underground Research Laboratory (HURL), Japan. Groundwater samples were obtained from three boreholes from a depth range of between 140 m and 250 m in two consecutive years. Groundwater was filtered and metagenomic DNA extracted and sequenced, and the sequence data assembled. Based on the sequences of phylogenetically informative genes on the assembled fragments, we detected a high degree of overlap in community composition across a vertical transect within one borehole at the two sampling times. However, there was comparatively little similarity observed among communities across boreholes. Spatial and temporal abundance patterns were used in combination with tetranucleotide signatures of assembled genome fragments to bin the data and reconstruct over 200 unique draft genomes, of which 137 are considered to be of high quality (>90% complete). The deepest samples from one borehole were highly dominated by an archaeon identified as ANME-2D; this organism was also present at lower abundance in all other samples from that borehole. Also abundant in these microbial communities were novel members of the Gammaproteobacteria, Saccharibacteria (TM7) and Tenericute phyla. Notably, a ~2 Mbp draft genome for the ANME-2D archaeon was reconstructed. As expected, the genome encodes all of the genes predicted to be involved in the reverse methanogenesis pathway. In contrast with the previously reported ANME2-D genome, the HURL ANME-2D genome lacks the capacity to reduce nitrate. However, we identified many multiheme cytochromes with closest similarity to those of the known Fe-reducing/oxidizing

  2. Amorphous tungstate precursor route to nanostructured tungsten oxide film with electrochromic property.

    PubMed

    Jeon, Ie-Rang; Kang, Joo-Hee; Paek, Seung-Min; Hwang, Seong-Ju; Choy, Jin-Ho

    2011-07-01

    Electrochromic tungsten oxide (WO3) films on ITO glass were fabricated by spin-coating with a tungsten peroxy acid solution, which was prepared by adding an equivolume mixture of hydrogen peroxide and glacial acetic acid to tungsten metal powder. The structural evolution of the tungstate precursor upon heat treatment was studied by X-ray diffraction (XRD) and X-ray absorption near edge structure (XANES) analyses, which indicated that the as-synthesized tungstate transformed into nanocrystalline WO3 upon heating. It is, therefore, quite clear that as-synthesized tungstate can be a good precursor for electrochromic WO3 films. A series of WO3 thin films were prepared on ITO glass by spin-coating with different concentrations of tungsten peroxy acid solution and then post-annealing at various temperatures. Depending on the concentration of the tungstate coating solution (200-500 mg mL(-1)) and the annealing temperature (100-300 degrees C), the thickness and WO3 content as well as the electrochromic properties of WO3 films can be controlled. As a result, the optimum fabrication conditions were determined to be a tungstate solution concentration of 300-400 mg mL(-1) and a post-annealing temperature of 200 degrees C. Finally, an inorganic-inorganic hybrid electrochromic device (ECD) composed of optimized WO3 and Prussian Blue (PB) with desirable coloration efficiency was successfully developed. PMID:22121748

  3. Selective hydrodeoxygenation of cyclic vicinal diols to cyclic alcohols over tungsten oxide-palladium catalysts.

    PubMed

    Amada, Yasushi; Ota, Nobuhiko; Tamura, Masazumi; Nakagawa, Yoshinao; Tomishige, Keiichi

    2014-08-01

    Hydrodeoxygenation of cyclic vicinal diols such as 1,4-anhydroerythritol was conducted over catalysts containing both a noble metal and a group 5-7 transition-metal oxide. The combination of Pd and WOx allowed the removal of one of the two OH groups selectively. 3-Hydroxytetrahydrofuran was obtained from 1,4-anhydroerythritol in 72 and 74% yield over WOx -Pd/C and WOx -Pd/ZrO2 , respectively. The WOx -Pd/ZrO2 catalyst was reusable without significant loss of activity if the catalyst was calcined as a method of regeneration. Characterization of WOx -Pd/C with temperature-programmed reduction, X-ray diffraction, and transmission electron microscopy/energy-dispersive X-ray spectroscopy suggested that Pd metal particles approximately 9 nm in size were formed on amorphous tungsten oxide particles. A reaction mechanism was proposed on the basis of kinetics, reaction results with tungsten oxides under an atmosphere of Ar, and density functional theory calculations. A tetravalent tungsten center (W(IV) ) was formed by reduction of WO3 with the Pd catalyst and H2 , and this center served as the reductant for partial hydrodeoxygenation.

  4. One-step breaking and separating emulsion by tungsten oxide coated mesh.

    PubMed

    Lin, Xin; Lu, Fei; Chen, Yuning; Liu, Na; Cao, Yingze; Xu, Liangxin; Wei, Yen; Feng, Lin

    2015-04-22

    Tungsten oxide coated mesh has been fabricated by a simple and inexpensive method. This coated mesh has a dual structure on the surface, consisting of microscale "flower" and nanoscale acicular crystal as the "petal". Combining the micro/nano structure of the surface and the native hydrophilic property of tungsten oxide, the coated mesh shows special wettability: superhydrophilic in air and superoleophobic under water. Because of the special wettability, such a mesh can be used to separate oil/water mixtures as well as emulsions. Attributed to the good water adsorption capacity of tungsten oxide, the abundant grooves of the micro/nanostructure, and the microsized pores of the surface, this coated mesh can accomplish the demulsification process and the separation process in one single-step, and no further post treatment is needed. As an "emulsion breaker and separator", this kind of mesh gives another idea of emulsion separation, which has prospective application in industrial fields such as water treatment and petroleum refining.

  5. Novel 2D RuPt core-edge nanocluster catalyst for CO electro-oxidation

    NASA Astrophysics Data System (ADS)

    Grabow, Lars C.; Yuan, Qiuyi; Doan, Hieu A.; Brankovic, Stanko R.

    2015-10-01

    A single layer, bi-metallic RuPt catalyst on Au(111) is synthesized using surface limited red-ox replacement of underpotentially deposited Cu and Pb monolayers though a two-step process. The resulting 2D RuPt monolayer nanoclusters have a unique core-edge structure with a Ru core and Pt at the edge along the perimeter. The activity of this catalyst is evaluated using CO monolayer oxidation as the probe reaction. Cyclic voltammetry demonstrates that the 2D RuPt core-edge catalyst morphology is significantly more active than either Pt or Ru monolayer catalysts. Density functional theory calculations in combination with infra-red spectroscopy data point towards oscillating variations (ripples) in the adsorption energy landscape along the radial direction of the Ru core as the origin of the observed behavior. Both, CO and OH experience a thermodynamic driving force for surface migration towards the Ru-Pt interface, where they adsorb most strongly and react rapidly. We propose that the complex interplay between epitaxial strain, ligand and finite size effects is responsible for the formation of the rippled RuPt monolayer cluster, which provides optimal conditions for a quasi-ideal bi-functional mechanism for CO oxidation, in which CO is adsorbed mainly on Pt, and Ru provides OH to the active Pt-Ru interface.

  6. Preventing Oxidation Near Gas/Tungsten-Arc Welds

    NASA Technical Reports Server (NTRS)

    Reed, K. J.

    1987-01-01

    Auxiliary argon jets create more nearly complete nonoxidizing atmosphere. Pyramid-shaped cup directs stream of additional argon over weld. Gas supplements provided by automatic welding machine so oxidation more completely suppressed.

  7. Chemical vapour deposition of tungsten oxide thin films from single-source precursors

    NASA Astrophysics Data System (ADS)

    Cross, Warren Bradley

    This thesis describes the chemical vapour deposition (CVD) of tungsten oxide thin films on glass from a wide range of single-source precursors. Chapter 1 describes previous work that has motivated this research. Chapter 2 discusses the synthesis of conventional style candidates for single-source precursors. Reactions of WOCl4 with 3-methyl salicylic acid (MesaliH2) and 3,5-di-iso-propyl salicylic acid (di-i-PrsaliH2) yielded the ditungsten complexes [WO(Mesali)(MesaliH)2(mu-O)], 1, and [WO(di-i-Prsali)(di-i-PrsaliH)2(mu-O)], 2, and the monotungsten complex [WO(di-i-Pr sali)(di-i-PrsaliH)Cl], 3. Tungsten(VI) dioxo complexes were prepared by ligand exchange reactions of [WO2(acac)2], 4, yielding [WO2(catH)2], 5, and [WO2(malt)2], 6, (catH2 = 3,5-di-tert-butyl-catechol; maltH = maltol). Chapter 3 describes thermal analyses of the complexes 1 - 6 and tungsten hexaphenoxide, and consequently their suitability for CVD. The use of [W(OPh)6] and 2 - 6 in aerosol assisted CVD is reported in Chapter 4. Brown tungsten oxide was deposited from 2 and 3 at 600 °C; blue partially-reduced WO3-x thin films were deposited from [W(OPh)6] from 300 to 500 °C, from 4 at 600 °C and 6 at 620 °C. Sintering all of the coatings in air at 550 °C afforded yellow films of stoichiometric WO3. Raman spectroscopy and glancing angle XRD showed that coatings deposited from [W(OPh)6] at 300 °C were amorphous, whereas all the other films were the monoclinic phase gamma-tungsten oxide. Taking full advantage of the aerosol vaporisation technique led to the CVD of tungsten oxide films from polyoxometalate single-source precursors, as described in Chapter 5. The isopolyanion [nBu4N]2[W6O19], 7, afforded WO3 at 410 °C; the heteropolyanions [nBu4N]4H3[PW11O39], 8, and [nBu4N]4[PNbW11O40], 9, were used to deposit doped WO3 thin films in a highly-controlled manner at 480 °C. Thus, the unprecedented use of large, charged clusters for CVD was demonstrated. Chapter 6 describes investigations of the

  8. GENERATION, TRANSPORT AND DEPOSITION OF TUNGSTEN-OXIDE AEROSOLS AT 1000 C IN FLOWING AIR-STEAM MIXTURES.

    SciTech Connect

    GREENE,G.A.; FINFROCK,C.C.

    2001-10-01

    Experiments were conducted to measure the rates of oxidation and vaporization of pure tungsten rods in flowing air, steam and air-steam mixtures in laminar flow. Also measured were the downstream transport of tungsten-oxide condensation aerosols and their region of deposition, including plateout in the superheated flow tube, rainout in the condenser and ambient discharge which was collected on an array of sub-micron aerosol filters. The nominal conditions of the tests, with the exception of the first two tests, were tungsten temperatures of 1000 C, gas mixture temperatures of 200 C and wall temperatures of 150 C to 200 C. It was observed that the tungsten oxidation rates were greatest in all air and least in all steam, generally decreasing non-linearly with increasing steam mole fraction. The tungsten oxidation rates in all air were more than five times greater than the tungsten oxidation rates in all steam. The tungsten vaporization rate was zero in all air and increased with increasing steam mole fraction. The vaporization rate became maximum at a steam mole fraction of 0.85 and decreased thereafter as the steam mole fraction was increased to unity. The tungsten-oxide was transported downstream as condensation aerosols, initially flowing upwards from the tungsten rod through an 18-inch long, one-inch diameter quartz tube, around a 3.5-inch radius, 90{sup o} bend and laterally through a 24-inch horizontal run. The entire length of the quartz glass flow path was heated by electrical resistance clamshell heaters whose temperatures were individually controlled and measured. The tungsten-oxide plateout in the quartz tube was collected, nearly all of which was deposited at the end of the heated zone near the entrance to the condenser which was cold. The tungsten-oxide which rained out in the condenser as the steam condensed was collected with the condensate and weighed after being dried. The aerosol smoke which escaped the condenser was collected on the sub

  9. Growth inhibition by tungsten in the sulfur-oxidizing bacterium Acidithiobacillus thiooxidans.

    PubMed

    Negishi, Atsunori; Muraoka, Tadashi; Maeda, Terunobu; Takeuchi, Fumiaki; Kanao, Tadayoshi; Kamimura, Kazuo; Sugio, Tsuyoshi

    2005-11-01

    Growth of five strains of sulfur-oxidizing bacteria Acidithiobacillus thiooxidans, including strain NB1-3, was inhibited completely by 50 microM of sodium tungstate (Na(2)WO(4)). When the cells of NB1-3 were incubated in 0.1 M beta-alanine-SO(4)(2-) buffer (pH 3.0) with 100 microM Na(2)WO(4) for 1 h, the amount of tungsten bound to the cells was 33 microg/mg protein. Approximately 10 times more tungsten was bound to the cells at pH 3.0 than at pH 7.0. The tungsten binding to NB1-3 cells was inhibited by oxyanions such as sodium molybdenum and ammonium vanadate. The activities of enzymes involved in elemental sulfur oxidation of NB1-3 cells such as sulfur oxidase, sulfur dioxygenase, and sulfite oxidase were strongly inhibited by Na(2)WO(4). These results indicate that tungsten binds to NB1-3 cells and inhibits the sulfur oxidation enzyme system of the cells, and as a result, inhibits cell growth. When portland cement bars supplemented with 0.075% metal nickel and with 0.075% metal nickel and 0.075% calcium tungstate were exposed to the atmosphere of a sewage treatment plant containing 28 ppm of H(2)S for 2 years, the weight loss of the portland cement bar with metal nickel and calcium tungstate was much lower than the cement bar containing 0.075% metal nickel.

  10. Single-step co-deposition of nanostructured tungsten oxide supported gold nanoparticles using a gold-phosphine cluster complex as the gold precursor

    NASA Astrophysics Data System (ADS)

    Molkenova, Anara; Sarip, Rozie; Sathasivam, Sanjay; Umek, Polona; Vallejos, Stella; Blackman, Chris; Hogarth, Graeme; Sankar, Gopinathan

    2014-12-01

    The use of a molecular gold organometallic cluster in chemical vapour deposition is reported, and it is utilized, together with a tungsten oxide precursor, for the single-step co-deposition of (nanostructured) tungsten oxide supported gold nanoparticles (NPs). The deposited gold-NP and tungsten oxide supported gold-NP are highly active catalysts for benzyl alcohol oxidation; both show higher activity than SiO2 supported gold-NP synthesized via a solution-phase method, and tungsten oxide supported gold-NP show excellent selectivity for conversion to benzaldehyde.

  11. Tungsten oxide--fly ash oxide composites in adsorption and photocatalysis.

    PubMed

    Visa, Maria; Bogatu, Cristina; Duta, Anca

    2015-05-30

    A novel composite based on tungsten oxide and fly ash was hydrothermally synthetized to be used as substrate in the advanced treatment of wastewaters with complex load resulted from the textile industry. The proposed treatment consists of one single step process combining photocatalysis and adsorption. The composite's crystalline structure was investigated by X-ray diffraction and FTIR, while atomic force microscopy (AFM) and scanning electron microscopy (SEM) were used to analyze the morphology. The adsorption capacity and photocatalytic properties of the material were tested on mono- and multi-pollutants systems containing two dyes (Bemacid Blau - BB and Bemacid Rot - BR) and one heavy metal ion-Cu(2+), and the optimized process conditions were identified. The results indicate better removal efficiencies using the novel composite material in the combined adsorption and photocatalysis, as compared to the separated processes. Dyes removal was significantly enhanced in the photocatalytic process by adding hydrogen peroxide and the mechanism was presented and discussed. The pseudo second order kinetics model best fitted the experimental data, both in the adsorption and in the combined processes. The kinetic parameters were calculated and correlated with the properties of the composite substrate.

  12. Covalent attachment of diamondoid phosphonic acid dichlorides to tungsten oxide surfaces.

    PubMed

    Li, Fei Hua; Fabbri, Jason D; Yurchenko, Raisa I; Mileshkin, Alexander N; Hohman, J Nathan; Yan, Hao; Yuan, Hongyuan; Tran, Ich C; Willey, Trevor M; Bagge-Hansen, Michael; Dahl, Jeremy E P; Carlson, Robert M K; Fokin, Andrey A; Schreiner, Peter R; Shen, Zhi-Xun; Melosh, Nicolas A

    2013-08-01

    Diamondoids (nanometer-sized diamond-like hydrocarbons) are a novel class of carbon nanomaterials that exhibit negative electron affinity (NEA) and strong electron-phonon scattering. Surface-bound diamondoid monolayers exhibit monochromatic photoemission, a unique property that makes them ideal electron sources for electron-beam lithography and high-resolution electron microscopy. However, these applications are limited by the stability of the chemical bonding of diamondoids on surfaces. Here we demonstrate the stable covalent attachment of diamantane phosphonic dichloride on tungsten/tungsten oxide surfaces. X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared (FTIR) spectroscopy revealed that diamondoid-functionalized tungsten oxide films were stable up to 300-350 °C, a substantial improvement over conventional diamondoid thiolate monolayers on gold, which dissociate at 100-200 °C. Extreme ultraviolet (EUV) light stimulated photoemission from these diamondoid phosphonate monolayers exhibited a characteristic monochromatic NEA peak with 0.2 eV full width at half-maximum (fwhm) at room temperature, showing that the unique monochromatization property of diamondoids remained intact after attachment. Our results demonstrate that phosphonic dichloride functionality is a promising approach for forming stable diamondoid monolayers for elevated temperature and high-current applications such as electron emission and coatings in micro/nano electromechanical systems (MEMS/NEMS).

  13. Investigations on bactericidal properties of molybdenum-tungsten oxides combinatorial thin film material libraries.

    PubMed

    Mardare, Cezarina Cela; Hassel, Achim Walter

    2014-11-10

    A combinatorial thin film material library from the molybdenum-tungsten refractory metals oxides system was prepared by thermal coevaporation, and its structural and morphological properties were investigated after a multiple step heat treatment. A mixture of crystalline and amorphous oxides and suboxides was obtained, as well as surface structuring caused by the enrichment of molybdenum oxides in large grains. It was found that the oxide phases and the surface morphology change as a function of the compositional gradient. Tests of the library antimicrobial activity against E. coli were performed and the antimicrobial activity was proven in some defined compositional ranges. A mechanism for explaining the observed activity is proposed, involving a collective contribution from (i) increased local acidity due to the enrichment in large grains of molybdenum oxides with different stoichiometry and (ii) the release of free radicals from the W18O49 phase under visible light.

  14. Acidic Ultrafine Tungsten Oxide Molecular Wires for Cellulosic Biomass Conversion.

    PubMed

    Zhang, Zhenxin; Sadakane, Masahiro; Hiyoshi, Norihito; Yoshida, Akihiro; Hara, Michikazu; Ueda, Wataru

    2016-08-22

    The application of nanocatalysis based on metal oxides for biomass conversion is of considerable interest in fundamental research and practical applications. New acidic transition-metal oxide molecular wires were synthesized for the conversion of cellulosic biomass. The ultrafine molecular wires were constructed by repeating (NH4 )2 [XW6 O21 ] (X=Te or Se) along the length, exhibiting diameters of only 1.2 nm. The nanowires dispersed in water and were observed using high-angle annular dark-field scanning transmission electron microscopy. Acid sites were created by calcination without collapse of the molecular wire structure. The acidic molecular wire exhibited high activity and stability and promoted the hydrolysis of the glycosidic bond. Various biomasses including cellulose were able to be converted to hexoses as main products. PMID:27482857

  15. Manganese oxide nanosheets and a 2D hybrid of graphene-manganese oxide nanosheets synthesized by liquid-phase exfoliation

    NASA Astrophysics Data System (ADS)

    Coelho, João; Mendoza-Sánchez, Beatriz; Pettersson, Henrik; Pokle, Anuj; McGuire, Eva K.; Long, Edmund; McKeon, Lorcan; Bell, Alan P.; Nicolosi, Valeria

    2015-06-01

    Manganese oxide nanosheets were synthesized using liquid-phase exfoliation that achieved suspensions in isopropanol (IPA) with concentrations of up to 0.45 mg ml-1. A study of solubility parameters showed that the exfoliation was optimum in N,N-dimethylformamide followed by IPA and diethylene glycol. IPA was the solvent of choice due to its environmentally friendly nature and ease of use for further processing. For the first time, a hybrid of graphene and manganese oxide nanosheets was synthesized using a single-step co-exfoliation process. The two-dimensional (2D) hybrid was synthesized in IPA suspensions with concentrations of up to 0.5 mg ml-1 and demonstrated stability against re-aggregation for up to six months. The co-exfoliation was found to be a energetically favorable process in which both solutes, graphene and manganese oxide nanosheets, exfoliate with an improved yield as compared to the single-solute exfoliation procedure. This work demonstrates the remarkable versatility of liquid-phase exfoliation with respect to the synthesis of hybrids with tailored properties, and it provides proof-of-concept ground work for further future investigation and exploitation of hybrids made of two or more 2D nanomaterials that have key complementary properties for various technological applications.

  16. Recent progress in tungsten oxides based memristors and their neuromorphological applications

    NASA Astrophysics Data System (ADS)

    Qu, Bo; Younis, Adnan; Chu, Dewei

    2016-09-01

    The advance in conventional silicon based semiconductor industry is now becoming indeterminacy as it still along the road of Moore's Law and concomitant problems associated with it are the emergence of a number of practical issues such as short channel effect. In terms of memory applications, it is generally believed that transistors based memory devices will approach to their scaling limits up to 2018. Therefore, one of the most prominent challenges today in semiconductor industry is the need of a new memory technology which is able to combine the best characterises of current devices. The resistive switching memories which are regarded as "memristors" thus gain great attentions thanks to their specific nonlinear electrical properties. More importantly, their behaviour resembles with the transmission characteristic of synapse in biology. Therefore, the research of synapses biomimetic devices based on memristor will certainly bring a great research prospect in studying synapse emulation as well as building artificial neural networks. Tungsten oxides (WO x ) exhibits many essential characteristics as a great candidate for memristive devices including: accredited endurance (over 105 cycles), stoichiometric flexibility, complimentary metal-oxide-semiconductor (CMOS) process compatibility and configurable properties including non-volatile rectification, memorization and learning functions. Herein, recent progress on Tungsten oxide based materials and its associating memory devices had been reviewed. The possible implementation of this material as a bio-inspired artificial synapse is also highlighted. The penultimate section summaries the current research progress for tungsten oxide based biological synapses and end up with several proposals that have been suggested for possible future developments.

  17. Assembly of tungsten oxide nanobundles and their electrochromic properties

    NASA Astrophysics Data System (ADS)

    Chang, Xueting; Sun, Shibin; Li, Zhenjiang; Xu, Xiao; Qiu, Yanyan

    2011-04-01

    Lenticular W18O49 nanobundles composed of ultra-thin nanowires with diameters of 5-10 nm have been synthesized through a simple solvothermal method with hexachloride as precursor and mixed cyclohexanol and ethanol as solvent. Electrochromic films were prepared by assembling the W18O49 nanobundle suspension onto tin-doped indium oxide (ITO) coated glass. Results showed that self-assembly of the W18O49 nanobundles was strongly influenced by the solvents employed to disperse the nanobundles. The W18O49 nanobundles coated films exhibited excellent electrochromic stability and reversibility. The W18O49 nanobundle films also showed much higher charge-insertion density compared with the WO3 nanorod film, which may be due to the ultrathin feature of single nanowires constituting the nanobundles, unique oxygen vacancies of monoclinic W18O49, and the highly ordered assembly of the nanobundles.

  18. Optical properties of tungsten oxide thin films with protons intercalated during sputtering

    SciTech Connect

    Yamada, Y.; Tajima, K.; Bao, S.; Okada, M.; Yoshimura, K.; Roos, A.

    2008-03-15

    Tungsten oxide thin films with protons intercalated during deposition (H{sub x}WO{sub 3}) were prepared using reactive direct-current-magnetron sputtering in a gas mixture of argon, oxygen, and hydrogen. The as-deposited films fabricated under suitable conditions were colored due to the formation of tungsten bronze. The concentration of intercalated protons, given by the x values in H{sub x}WO{sub 3}, was evaluated by ejecting protons electrochemically from the films. The x value of the films prepared at a constant working pressure was found to be proportional to the hydrogen flow ratio during deposition. On the other hand, the x value of the films prepared at a constant hydrogen flow ratio decreased sharply with increasing working pressure during deposition. The dispersion of the extinction coefficient ({kappa}) of the films was estimated by analyzing the experimental spectra of {psi} and {delta} measured with spectroscopic ellipsometry using the model composed of a homogeneous tungsten bronze layer with an additional surface roughness layer. As a result of this analysis, the {kappa} value was found to increase sharply with the number of intercalated protons. There was a linear dependence between the {kappa} value and the x value for x<0.2, while for x>0.3, the absorption saturated. This indicates that it is possible to evaluate the x value of H{sub x}WO{sub 3} films using spectroscopic ellipsometry.

  19. Degradation of electrochromic film of amorphous tungsten oxide after coloration

    NASA Astrophysics Data System (ADS)

    Luo, Zhongkuan

    1992-11-01

    The degradation of the electrochromic film of a-WO3 was investigated from the equilibrium state of different driving voltage and the time dependent emf was also obtained in an open or short circuit of zero volts. Based on the mechanism of activation and the principal of chemical reaction kinetics, the correct definition of electrochromic memory was made and a relation of memory was obtained. It was also found that at the initial time of natural bleaching, the change rate of proton concentration in the film was also obtained. According to the mechanism of electrochromic memory, it was indicated that in the open circuit case, the theoretical reaction of the change rate of electric potential was in good agrement with the experimental results, and furthermore, the reaction constant was determined with the experimental data. In the short circuit case, there exist two effects on degradation, the short circuit current caused by the backward emf, and the oxidation of the colored film. The experimental data shows that, in the short circuit case, the degradation strongly depends on the short circuit current and the effect of chemical reaction can be neglected.

  20. Cobalt oxide 2D nano-assemblies from infinite coordination polymer precursors mediated by a multidentate pyridyl ligand.

    PubMed

    Li, Guo-Rong; Xie, Chen-Chao; Shen, Zhu-Rui; Chang, Ze; Bu, Xian-He

    2016-05-01

    In this work, the construction of Co3O4 two dimensional (2D) nano-assemblies utilizing infinite coordination polymers (ICPs) as precursors was investigated, aiming at the morphology targeted fabrication and utilization of 2D materials. Based on the successful modulation of morphology, a rose-like Co based ICP precursor was obtained, which was further transformed into porous Co3O4 nanoflake assemblies with a well-preserved 2D morphology and a large surface area. The mechanism of the morphology modulation was illustrated by systematic investigation, which demonstrated the crucial role of a modulating agent in the formation of 2D nano-assemblies. In addition, the cobalt oxide 2D nano-assemblies are fabricated into a lithium anode combined with graphene, and the remarkable capacity and stability (900 mA h g(-1) after 50 cycles) of the resulting Co3O4/G nanocomposite indicates its potential in lithium battery applications. PMID:27064264

  1. Cobalt oxide 2D nano-assemblies from infinite coordination polymer precursors mediated by a multidentate pyridyl ligand.

    PubMed

    Li, Guo-Rong; Xie, Chen-Chao; Shen, Zhu-Rui; Chang, Ze; Bu, Xian-He

    2016-05-01

    In this work, the construction of Co3O4 two dimensional (2D) nano-assemblies utilizing infinite coordination polymers (ICPs) as precursors was investigated, aiming at the morphology targeted fabrication and utilization of 2D materials. Based on the successful modulation of morphology, a rose-like Co based ICP precursor was obtained, which was further transformed into porous Co3O4 nanoflake assemblies with a well-preserved 2D morphology and a large surface area. The mechanism of the morphology modulation was illustrated by systematic investigation, which demonstrated the crucial role of a modulating agent in the formation of 2D nano-assemblies. In addition, the cobalt oxide 2D nano-assemblies are fabricated into a lithium anode combined with graphene, and the remarkable capacity and stability (900 mA h g(-1) after 50 cycles) of the resulting Co3O4/G nanocomposite indicates its potential in lithium battery applications.

  2. Mechanism and Microstructure of Oxide Fluxes for Gas Tungsten Arc Welding of Magnesium Alloy

    NASA Astrophysics Data System (ADS)

    Liu, L. M.; Zhang, Z. D.; Song, G.; Wang, L.

    2007-03-01

    Five single oxide fluxes—MgO, CaO, TiO2, MnO2, and Cr2O3—were used to investigate the effect of active flux on the depth/width ratio in AZ31B magnesium alloy. The microstructure and mechanical property of the tungsten inert gas (TIG) welding seam were studied. The oxygen content in the weld seam and the arc images during the TIG welding process were analyzed. A series of emission spectroscopy of weld arc for TIG welding for magnesium with and without flux were developed. The results showed that for the five single oxide fluxes, all can increase the weld penetration effectively and grain size in the weld seam of alternating current tungsten inert gas (ACTIG) welding of the Mg alloy. The oxygen content of the welds made without flux is not very different from those produced with oxide fluxes not considering trapped oxide. However, welds that have the best penetration have a relatively higher oxygen content among those produced with flux. It was found that the arc images with the oxide fluxes were only the enlarged form of the arc images without flux; the arc constriction was not observed. The detection of arc spectroscopy showed that the metal elements in the oxides exist as the neutral atom or the first cation in the weld arc. This finding would influence the arc properties. When TIG simulation was carried out on a plate with flux applied only on one side, the arc image video showed an asymmetric arc, which deviated toward the flux free side. The thermal stability, the dissociation energy, and the electrical conductivity of oxide should be considered when studying the mechanism for increased TIG flux weld penetration.

  3. Mesoporous carbon nitride-tungsten oxide composites for enhanced photocatalytic hydrogen evolution.

    PubMed

    Kailasam, Kamalakannan; Fischer, Anna; Zhang, Guigang; Zhang, Jinshui; Schwarze, Michael; Schröder, Marc; Wang, Xinchen; Schomäcker, Reinhard; Thomas, Arne

    2015-04-24

    Composites of mesoporous polymeric carbon nitride and tungsten(VI) oxide show very high photocatalytic activity for the evolution of hydrogen from water under visible light and in the presence of sacrificial electron donors. Already addition of very small amounts of WO3 yields up to a twofold increase in the efficiency when compared to bulk carbon nitrides and their composites and more notably even to the best reported mesoporous carbon nitride-based photocatalytic materials. The higher activity can be attributed to the high surface area and synergetic effect of the carbon nitrides and the WO3 resulting in improved charge separation through a photocatalytic solid-state Z-scheme mechanism.

  4. Aerosol assisted chemical vapour deposition control parameters for selective deposition of tungsten oxide nanostructures.

    PubMed

    Vallejos, S; Umek, P; Blackman, C

    2011-09-01

    Tungsten oxide films were deposited via Aerosol Assisted Chemical Vapour Deposition (AACVD) from the single-source precursor W(OPh)6. Film morphology and optimum deposition temperatures for formation of quasi-one-dimensional structures is influenced by the solvent 'carrier' used for deposition of the films with bulk porous films and nanostructured needles, hollow tubes and fibres obtained dependent on the solvent used and the deposition temperature. This influence of solvent could be exploited for the synthesis of other nanomaterials, and so provide a new and versatile route to develop and integrate nanostructured materials for device applications. PMID:22097557

  5. Optical constants of amorphous, transparent titanium-doped tungsten oxide thin films.

    PubMed

    Ramana, C V; Baghmar, Gaurav; Rubio, Ernesto J; Hernandez, Manuel J

    2013-06-12

    We report on the optical constants and their dispersion profiles determined from spectroscopic ellipsometry (SE) analysis of the 20%-titanium (Ti) doped of tungsten oxide (WO3) thin films grown by sputter-deposition. The Ti-doped WO3 films grown in a wide range of temperatures (25-500 °C) are amorphous and optically transparent. SE data indicates that there is no significant interdiffusion at the film-substrate interface for a W-Ti oxide film growth of ~90 nm. The index refraction (n) at λ = 550 nm vary in the range of 2.17-2.31 with a gradual increase in growth temperature. A correlation between the growth conditions and optical constants is discussed. PMID:23682744

  6. Tungsten oxide proton conducting films for low-voltage transparent oxide-based thin-film transistors

    SciTech Connect

    Zhang, Hongliang; Wan, Qing; Wan, Changjin; Wu, Guodong; Zhu, Liqiang

    2013-02-04

    Tungsten oxide (WO{sub x}) electrolyte films deposited by reactive magnetron sputtering showed a high room temperature proton conductivity of 1.38 Multiplication-Sign 10{sup -4} S/cm with a relative humidity of 60%. Low-voltage transparent W-doped indium-zinc-oxide thin-film transistors gated by WO{sub x}-based electrolytes were self-assembled on glass substrates by one mask diffraction method. Enhancement mode operation with a large current on/off ratio of 4.7 Multiplication-Sign 10{sup 6}, a low subthreshold swing of 108 mV/decade, and a high field-effect mobility 42.6 cm{sup 2}/V s was realized. Our results demonstrated that WO{sub x}-based proton conducting films were promising gate dielectric candidates for portable low-voltage oxide-based devices.

  7. Tungsten oxide proton conducting films for low-voltage transparent oxide-based thin-film transistors

    NASA Astrophysics Data System (ADS)

    Zhang, Hongliang; Wan, Qing; Wan, Changjin; Wu, Guodong; Zhu, Liqiang

    2013-02-01

    Tungsten oxide (WOx) electrolyte films deposited by reactive magnetron sputtering showed a high room temperature proton conductivity of 1.38 × 10-4 S/cm with a relative humidity of 60%. Low-voltage transparent W-doped indium-zinc-oxide thin-film transistors gated by WOx-based electrolytes were self-assembled on glass substrates by one mask diffraction method. Enhancement mode operation with a large current on/off ratio of 4.7 × 106, a low subthreshold swing of 108 mV/decade, and a high field-effect mobility 42.6 cm2/V s was realized. Our results demonstrated that WOx-based proton conducting films were promising gate dielectric candidates for portable low-voltage oxide-based devices.

  8. Effects of working pressure on physical properties of tungsten-oxide thin films sputtered from oxide target

    SciTech Connect

    Riech, I.; Acosta, M.; Pena, J. L.; Bartolo-Perez, P.

    2010-03-15

    Tungsten-oxide films were deposited on glass substrates from a metal-oxide target by nonreactive radio-frequency sputtering. The authors have studied the effect that changing Ar gas pressure has on the electrical, optical, and chemical composition in the thin films. Resistivity of WO{sub 3} changed ten orders of magnitude with working gas pressure values from 20 to 80 mTorr. Thin films deposited at 20 mTorr of Ar sputtering pressure showed lower resistivity and optical transmittance. X-ray photoelectron spectroscopy (XPS) measurements revealed similar chemical composition for all samples irrespective of Ar pressure used. However, XPS analyses of the evolution of W 4f and O 1s peaks indicated a mixture of oxides dependent on the Ar pressure used during deposition.

  9. Atomic thin titania nanosheet-coupled reduced graphene oxide 2D heterostructures for enhanced photocatalytic activity and fast lithium storage

    NASA Astrophysics Data System (ADS)

    Li, Dong Jun; Huang, Zhegang; Hwang, Tae Hoon; Narayan, Rekha; Choi, Jang Wook; Kim, Sang Ouk

    2016-03-01

    Realizing practical high performance materials and devices using the properties of 2D materials is of key research interest in the materials science field. In particular, building well-defined heterostructures using more than two different 2D components in a rational way is highly desirable. In this paper, a 2D heterostructure consisting of atomic thin titania nanosheets densely grown on reduced graphene oxide surface is successfully prepared through incorporating polymer functionalized graphene oxide into the novel TiO2 nanosheets synthesis scheme. As a result of the synergistic combination of a highly accessible surface area and abundant interface, which can modulate the physicochemical properties, the resultant heterostructure can be used in high efficiency visible light photocatalysis as well as fast energy storage with a long lifecycle. [Figure not available: see fulltext.

  10. Pseudocapacitive Electrodes Produced by Oxidant-Free Polymerization of Pyrrole between the Layers of 2D Titanium Carbide (MXene).

    PubMed

    Boota, Muhammad; Anasori, Babak; Voigt, Cooper; Zhao, Meng-Qiang; Barsoum, Michel W; Gogotsi, Yury

    2016-02-17

    Heterocyclic pyrrole molecules are in situ aligned and polymerized in the -absence of an oxidant between layers of the 2D Ti3C2Tx (MXene), resulting in high volumetric and gravimetric capacitances with capacitance retention of 92% after 25,000 cycles at a 100 mV s(-1) scan rate.

  11. Pseudocapacitive Electrodes Produced by Oxidant-Free Polymerization of Pyrrole between the Layers of 2D Titanium Carbide (MXene)

    DOE PAGES

    Boota, M.; Anasori, Babak; Voigt, C.; Zhao, Meng-Qiang; Barsoum, M. W.; Gogotsi, Yury

    2016-02-17

    Heterocyclic pyrrole molecules are in situ aligned and polymerized in the ­absence of an oxidant between layers of the 2D Ti3C2Tx (MXene), resulting in high volumetric and gravimetric capacitances with capacitance retention of 92% after 25 000 cycles at a 100 mV s-1 scan rate.

  12. Tungsten species in natural ferromanganese oxides related to its different behavior from molybdenum in oxic ocean

    NASA Astrophysics Data System (ADS)

    Kashiwabara, Teruhiko; Takahashi, Yoshio; Marcus, Matthew A.; Uruga, Tomoya; Tanida, Hajime; Terada, Yasuko; Usui, Akira

    2013-04-01

    The tungsten (W) species in marine ferromanganese oxides were investigated by wavelength dispersive XAFS method. We found that the W species are in distorted Oh symmetry in natural ferromanganese oxides. The host phase of W is suggested to be Mn oxides by μ-XRF mapping. We also found that the W species forms inner-sphere complexes in hexavalent state and distorted Oh symmetry on synthetic ferrihydrite, goethite, hematite, and δ-MnO2. The molecular-scale information of W indicates that the negatively-charged WO42- ion mainly adsorbs on the negatively-charged Mn oxides phase in natural ferromanganese oxides due to the strong chemical interaction. In addition, preferential adsorption of lighter W isotopes is expected based on the molecular symmetry of the adsorbed species, implying the potential significance of the W isotope systems similar to Mo. Adsorption experiments of W on synthetic ferrihydrite and δ-MnO2 were also conducted. At higher equilibrium concentration, W exhibits behaviors similar to Mo on δ-MnO2 due to their formations of inner-sphere complexes. On the other hand, W shows a much larger adsorption on ferrihydrite than Mo. This is due to the formation of the inner- and outer-sphere complexes for W and Mo on ferrihydrite, respectively. Considering the lower equilibrium concentration such as in oxic seawater, however, the enrichment of W into natural ferromanganese oxides larger than Mo may be controlled by the different stabilities of their inner-sphere complexes on the Mn oxides. These two factors, (i) the stability of inner-sphere complexes on the Mn oxides and (ii) the mode of attachment on ferrihydrite (inner- or outer-sphere complex), are the causes of the different behaviors of W and Mo on the surface of the Fe/Mn (oxyhydr)oxides.

  13. Colouration process of colloidal tungsten oxide nanoparticles in the presence of hydrogen gas

    NASA Astrophysics Data System (ADS)

    Tahmasebi Garavand, N.; Ranjbar, M.; Mahdavi, S. M.; Iraji zad, A.

    2012-10-01

    In this study, tungsten oxide nanoparticles were fabricated by pulsed laser ablation (PLA) of tungsten target using the first harmonic of a Nd:YAG laser (1064 nm) in deionized water. After ablation, a 0.2 g/lit PdCl2 solution was added to activate the solution against the hydrogen gas. Dynamic light scattering and X-ray photoelectron spectroscopy were used to measure the average size and the surface chemical composition of the synthesized nanoparticles, respectively. The aim is to investigate the influence of hydrogen exposure time on colouration process of colloidal nanoparticles. According to optical measurements, hydrogen bubbling into the produced colloidal Pd-WO3 led to formation of several absorption peaks at ∼1.26, ∼1.6 and ∼1.97 eV. We observed the appearance and growth of a peak at 1.6 eV at the initial stages of hydrogen exposure. However, two other peaks became dominant at long exposure times. The coloration process is reversible in the presence of oxygen gas.

  14. Impact of Nanosize on Supercapacitance: Study of 1D Nanorods and 2D Thin-Films of Nickel Oxide.

    PubMed

    Patil, Ranjit A; Chang, Cheng-Ping; Devan, Rupesh S; Liou, Yung; Ma, Yuan-Ron

    2016-04-20

    We synthesized unique one-dimensional (1D) nanorods and two-dimensional (2D) thin-films of NiO on indium-tin-oxide thin-films using a hot-filament metal-oxide vapor deposition technique. The 1D nanorods have an average width and length of ∼100 and ∼500 nm, respectively, and the densely packed 2D thin-films have an average thickness of ∼500 nm. The 1D nanorods perform as parallel units for charge storing. However, the 2D thin-films act as one single unit for charge storing. The 2D thin-films possess a high specific capacitance of ∼746 F/g compared to 1D nanorods (∼230 F/g) using galvanostatic charge-discharge measurements at a current density of 3 A/g. Because the 1D NiO nanorods provide more plentiful surface areas than those of the 2D thin-films, they are fully active at the first few cycles. However, the capacitance retention of the 1D nanorods decays faster than that of the 2D thin-films. Also, the 1D NiO nanorods suffer from instability due to the fast electrochemical dissolution and high nanocontact resistance. Electrochemical impedance spectroscopy verifies that the low dimensionality of the 1D NiO nanorods induces the unavoidable effects that lead them to have poor supercapacitive performances. On the other hand, the slow electrochemical dissolution and small contact resistance in the 2D NiO thin-films favor to achieve high specific capacitance and great stability.

  15. Impact of Nanosize on Supercapacitance: Study of 1D Nanorods and 2D Thin-Films of Nickel Oxide.

    PubMed

    Patil, Ranjit A; Chang, Cheng-Ping; Devan, Rupesh S; Liou, Yung; Ma, Yuan-Ron

    2016-04-20

    We synthesized unique one-dimensional (1D) nanorods and two-dimensional (2D) thin-films of NiO on indium-tin-oxide thin-films using a hot-filament metal-oxide vapor deposition technique. The 1D nanorods have an average width and length of ∼100 and ∼500 nm, respectively, and the densely packed 2D thin-films have an average thickness of ∼500 nm. The 1D nanorods perform as parallel units for charge storing. However, the 2D thin-films act as one single unit for charge storing. The 2D thin-films possess a high specific capacitance of ∼746 F/g compared to 1D nanorods (∼230 F/g) using galvanostatic charge-discharge measurements at a current density of 3 A/g. Because the 1D NiO nanorods provide more plentiful surface areas than those of the 2D thin-films, they are fully active at the first few cycles. However, the capacitance retention of the 1D nanorods decays faster than that of the 2D thin-films. Also, the 1D NiO nanorods suffer from instability due to the fast electrochemical dissolution and high nanocontact resistance. Electrochemical impedance spectroscopy verifies that the low dimensionality of the 1D NiO nanorods induces the unavoidable effects that lead them to have poor supercapacitive performances. On the other hand, the slow electrochemical dissolution and small contact resistance in the 2D NiO thin-films favor to achieve high specific capacitance and great stability. PMID:27028491

  16. A room temperature nitric oxide gas sensor based on a copper-ion-doped polyaniline/tungsten oxide nanocomposite.

    PubMed

    Wang, Shih-Han; Shen, Chi-Yen; Su, Jian-Ming; Chang, Shiang-Wen

    2015-03-24

    The parts-per-billion-level nitric oxide (NO) gas sensing capability of a copper-ion-doped polyaniline/tungsten oxide nanocomposite (Cu(2+)/PANI/WO3) film coated on a Rayleigh surface acoustic wave device was investigated. The sensor developed in this study was sensitive to NO gas at room temperature in dry nitrogen. The surface morphology, dopant distribution, and electric properties were characterized using scanning electron microscopy, energy-dispersive X-ray spectroscopy mapping, and Hall effect measurements, respectively. The Cu(2+)/PANI/WO3 film exhibited high NO gas sensitivity and selectivity as well as long-term stability. At 1 ppb of NO, a signal with a frequency shift of 4.3 ppm and a signal-to-noise ratio of 17 was observed. The sensor exhibited distinct selectivity toward NO gas with no substantial response to O2, NH3 and CO2 gases.

  17. A Room Temperature Nitric Oxide Gas Sensor Based on a Copper-Ion-Doped Polyaniline/Tungsten Oxide Nanocomposite

    PubMed Central

    Wang, Shih-Han; Shen, Chi-Yen; Su, Jian-Ming; Chang, Shiang-Wen

    2015-01-01

    The parts-per-billion-level nitric oxide (NO) gas sensing capability of a copper-ion-doped polyaniline/tungsten oxide nanocomposite (Cu2+/PANI/WO3) film coated on a Rayleigh surface acoustic wave device was investigated. The sensor developed in this study was sensitive to NO gas at room temperature in dry nitrogen. The surface morphology, dopant distribution, and electric properties were characterized using scanning electron microscopy, energy-dispersive X-ray spectroscopy mapping, and Hall effect measurements, respectively. The Cu2+/PANI/WO3 film exhibited high NO gas sensitivity and selectivity as well as long-term stability. At 1 ppb of NO, a signal with a frequency shift of 4.3 ppm and a signal-to-noise ratio of 17 was observed. The sensor exhibited distinct selectivity toward NO gas with no substantial response to O2, NH3 and CO2 gases. PMID:25811223

  18. A room temperature nitric oxide gas sensor based on a copper-ion-doped polyaniline/tungsten oxide nanocomposite.

    PubMed

    Wang, Shih-Han; Shen, Chi-Yen; Su, Jian-Ming; Chang, Shiang-Wen

    2015-01-01

    The parts-per-billion-level nitric oxide (NO) gas sensing capability of a copper-ion-doped polyaniline/tungsten oxide nanocomposite (Cu(2+)/PANI/WO3) film coated on a Rayleigh surface acoustic wave device was investigated. The sensor developed in this study was sensitive to NO gas at room temperature in dry nitrogen. The surface morphology, dopant distribution, and electric properties were characterized using scanning electron microscopy, energy-dispersive X-ray spectroscopy mapping, and Hall effect measurements, respectively. The Cu(2+)/PANI/WO3 film exhibited high NO gas sensitivity and selectivity as well as long-term stability. At 1 ppb of NO, a signal with a frequency shift of 4.3 ppm and a signal-to-noise ratio of 17 was observed. The sensor exhibited distinct selectivity toward NO gas with no substantial response to O2, NH3 and CO2 gases. PMID:25811223

  19. The oxidation behavior of tungsten and germanium alloyed molybdenum disilicide coatings

    SciTech Connect

    Mueller, A.; Wang, Ge; Rapp, R.A. . Dept. of Materials Science and Engineering); Courtright, E.L. ); Kircher, T. . Aerospace Materials Div.)

    1991-11-01

    A two-step coating process was used to produce a (Mo,W)(Si,Ge){sub 2} coating on niobium. After exposure to high temperatures, a lower silicide layer forms underneath and is effective in arresting cracks. The oxidation weight-gain kinetics are parabolic following an initial transient period. Test coupons coated with (Mo,W)(Si,Ge){sub 2} passed 200 one-hour cycles at 1370{degree}C and 60 one-hour cycles at 1540{degree}C. These results, along with evidence of a thick protective glass layer, suggest that the germanium additions help cyclic oxidation resistance. The beneficial effects of the tungsten include the formation of microvoids, which provides a lower effective elastic modulus, and mechanical strengthening. No accelerated low temperature or pest'' oxidation was observed in the temperature range between 500--700{degree}C. Thus, a (Mo,W)(Si,Ge) multicomponent silicide coating offers significant promise for the protection of Nb-base alloys exposed to cyclic oxidizing environments over a broad range of temperatures.

  20. The oxidation behavior of tungsten and germanium alloyed molybdenum disilicide coatings

    SciTech Connect

    Mueller, A.; Wang, Ge; Rapp, R.A.; Courtright, E.L.; Kircher, T.

    1991-11-01

    A two-step coating process was used to produce a (Mo,W)(Si,Ge){sub 2} coating on niobium. After exposure to high temperatures, a lower silicide layer forms underneath and is effective in arresting cracks. The oxidation weight-gain kinetics are parabolic following an initial transient period. Test coupons coated with (Mo,W)(Si,Ge){sub 2} passed 200 one-hour cycles at 1370{degree}C and 60 one-hour cycles at 1540{degree}C. These results, along with evidence of a thick protective glass layer, suggest that the germanium additions help cyclic oxidation resistance. The beneficial effects of the tungsten include the formation of microvoids, which provides a lower effective elastic modulus, and mechanical strengthening. No accelerated low temperature or ``pest`` oxidation was observed in the temperature range between 500--700{degree}C. Thus, a (Mo,W)(Si,Ge) multicomponent silicide coating offers significant promise for the protection of Nb-base alloys exposed to cyclic oxidizing environments over a broad range of temperatures.

  1. Removal of ammonia from air on molybdenum and tungsten oxide modified activated carbons.

    PubMed

    Petit, Camille; Bandosz, Teresa J

    2008-04-15

    Microporous coconut-based activated carbon was impregnated with solutions of ammonium metatungstate or ammonium molybdate and then calcined in air in order to convert the salts into their corresponding oxides. The surface of those materials was characterized using adsorption of nitrogen, potentiometric titration, Fourier-transform infrared spectroscopy, X-ray diffraction, and thermal analysis. The results indicated a significant increase in surface acidity related to the presence of tungsten or molybdenum oxides. On the materials obtained, adsorption of ammonia from either dry or moist air was carried out. The oxides distributed on the surface provided Lewis and/or Brønsted centers for interactions with ammonia molecules or ammonium ions. Water on the surface of carbon or in the gas phase increased the amount of ammonia adsorbed via involvement of Brønsted-type interactions and/or by leading to the formation of molybdate or tungstate salts on the surface. Although the amount of ammonia adsorbed is closely related to the number of moles of oxides and their acidic centers, the carbon surface also contributes to the adsorption via providing small pores where ammonia can be dissolved in the water film.

  2. Low-Temperature Selective Growth of Tungsten Oxide Nanowires by Controlled Nanoscale Stress Induction.

    PubMed

    Na, Hyungjoo; Eun, Youngkee; Kim, Min-Ook; Choi, Jungwook; Kim, Jongbaeg

    2015-01-01

    We report a unique approach for the patterned growth of single-crystalline tungsten oxide (WOx) nanowires based on localized stress-induction. Ions implanted into the desired growth area of WOx thin films lead to a local increase in the compressive stress, leading to the growth of nanowire at lower temperatures (600 °C vs. 750-900 °C) than for equivalent non-implanted samples. Nanowires were successfully grown on the microscale patterns using wafer-level ion implantation and on the nanometer scale patterns using a focused ion beam (FIB). Experimental results show that nanowire growth is influenced by a number of factors including the dose of the implanted ions and their atomic radius. The implanted-ion-assisted, stress-induced method proposed here for the patterned growth of WOx nanowires is simpler than alternative approaches and enhances the compatibility of the process by reducing the growth temperature. PMID:26666843

  3. The solution growth route and characterization of electrochromic tungsten oxide thin films

    SciTech Connect

    Todorovski, Toni; Najdoski, Metodija

    2007-12-04

    Electrochromic tungsten oxide thin films were prepared by using an aqueous solution of Na{sub 2}WO{sub 4}.2H{sub 2}O and dimethyl sulfate. Various techniques were used for the characterization of the films such as X-ray diffraction, cyclic voltammetry, SEM analysis and VIS-spectroscopy. The thin film durability was tested in an aqueous solution of LiClO{sub 4} (0.1 mol/dm{sup 3}) for about 7000 cycles followed by cyclic voltammetry. No significant changes in the cyclic voltammograms were found, thus proving the high durability of the films. The optical transmittance spectra of coloured and bleached states showed significant change in the transmittance, which makes these films favorable for electrochromic devices.

  4. Low-Temperature Selective Growth of Tungsten Oxide Nanowires by Controlled Nanoscale Stress Induction

    NASA Astrophysics Data System (ADS)

    Na, Hyungjoo; Eun, Youngkee; Kim, Min-Ook; Choi, Jungwook; Kim, Jongbaeg

    2015-12-01

    We report a unique approach for the patterned growth of single-crystalline tungsten oxide (WOx) nanowires based on localized stress-induction. Ions implanted into the desired growth area of WOx thin films lead to a local increase in the compressive stress, leading to the growth of nanowire at lower temperatures (600 °C vs. 750-900 °C) than for equivalent non-implanted samples. Nanowires were successfully grown on the microscale patterns using wafer-level ion implantation and on the nanometer scale patterns using a focused ion beam (FIB). Experimental results show that nanowire growth is influenced by a number of factors including the dose of the implanted ions and their atomic radius. The implanted-ion-assisted, stress-induced method proposed here for the patterned growth of WOx nanowires is simpler than alternative approaches and enhances the compatibility of the process by reducing the growth temperature.

  5. Dual Oxygen and Tungsten Vacancies on a WO3 Photoanode for Enhanced Water Oxidation.

    PubMed

    Ma, Ming; Zhang, Kan; Li, Ping; Jung, Myung Sun; Jeong, Myung Jin; Park, Jong Hyeok

    2016-09-19

    Alleviating charge recombination at the electrode/electrolyte interface by introducing an overlayer is considered an efficient approach to improve photoelectrochemical (PEC) water oxidation. A WO3 overlayer with dual oxygen and tungsten vacancies was prepared by using a solution-based reducing agent, LEDA (lithium dissolved in ethylenediamine), which improved the PEC performance of the mesoporous WO3 photoanode dramatically. In comparison to the pristine samples, the interconnected WO3 nanoparticles surrounded by a 2-2.5 nm thick overlayer exhibited a photocurrent density approximately 2.4 times higher and a marked cathodic shift of the onset potential, which is mainly attributed to the facilitative effect on interface charge transfer and the improved conductivity by enhanced charge carrier density. This simple and effective strategy may provide a new path to improve the PEC performance of other photoanodes. PMID:27533279

  6. Robust superhydrophobic tungsten oxide coatings with photochromism and UV durability properties

    NASA Astrophysics Data System (ADS)

    Jiang, Ting; Guo, Zhiguang

    2016-11-01

    Robust superhydrophobic tungsten oxide (TO) coatings with a water contact angle (WCA) of 155° were developed for photochromism via a facile and substrate-independent route. Importantly, after scatch test on both a single and two orthogonal direction, the TO coating still exhibited superhydrophobic behavior, indicating excellent mechanical robustness. It is worth mentioning that the superhydrophobic TO coatings showed the reversible convert of photochromism of WO3 induced by alternating UV and visible light irradiation. Besides that, the TO coating remained superhydrophobicity after UV irradiation for 36 h, showing excellent UV durability. In addition, the coating showed good resistance to acidic droplets. Moreover, it can also be applied on other substrates, such as copper mesh, steel, paper and fiber. The coating exhibited excellent self-cleaning behavior due to its high WCA and low rolling angle. Overall, this work is a promising approach to design and produce functional superhydrophobic coatings for various substrates.

  7. Low-Temperature Selective Growth of Tungsten Oxide Nanowires by Controlled Nanoscale Stress Induction

    PubMed Central

    Na, Hyungjoo; Eun, Youngkee; Kim, Min-Ook; Choi, Jungwook; Kim, Jongbaeg

    2015-01-01

    We report a unique approach for the patterned growth of single-crystalline tungsten oxide (WOx) nanowires based on localized stress-induction. Ions implanted into the desired growth area of WOx thin films lead to a local increase in the compressive stress, leading to the growth of nanowire at lower temperatures (600 °C vs. 750–900 °C) than for equivalent non-implanted samples. Nanowires were successfully grown on the microscale patterns using wafer-level ion implantation and on the nanometer scale patterns using a focused ion beam (FIB). Experimental results show that nanowire growth is influenced by a number of factors including the dose of the implanted ions and their atomic radius. The implanted-ion-assisted, stress-induced method proposed here for the patterned growth of WOx nanowires is simpler than alternative approaches and enhances the compatibility of the process by reducing the growth temperature. PMID:26666843

  8. Tungsten oxide nanorods: an efficient nanoplatform for tumor CT imaging and photothermal therapy.

    PubMed

    Zhou, Zhiguo; Kong, Bin; Yu, Chao; Shi, Xiangyang; Wang, Mingwei; Liu, Wei; Sun, Yanan; Zhang, Yingjian; Yang, Hong; Yang, Shiping

    2014-01-13

    We report here a facile thermal decomposition approach to creating tungsten oxide nanorods (WO2.9 NRs) with a length of 13.1 ± 3.6 nm and a diameter of 4.4 ± 1.5 nm for tumor theranostic applications. The formed WO2.9 NRs were modified with methoxypoly(ethylene glycol) (PEG) carboxyl acid via ligand exchange to have good water dispersability and biocompatibility. With the high photothermal conversion efficiency irradiated by a 980 nm laser and the better X-ray attenuation property than clinically used computed tomography (CT) contrast agent Iohexol, the formed PEGylated WO2.9 NRs are able to inhibit the growth of the model cancer cells in vitro and the corresponding tumor model in vivo, and enable effective CT imaging of the tumor model in vivo. Our "killing two birds with one stone" strategy could be extended for fabricating other nanoplatforms for efficient tumor theranostic applications.

  9. Hydrothermal synthesis of self-assembled hierarchical tungsten oxides hollow spheres and their gas sensing properties.

    PubMed

    Li, Jinwei; Liu, Xin; Cui, Jiashan; Sun, Jianbo

    2015-05-20

    Hierarchical self-assembled hollow spheres (HS) of tungsten oxide nanosheets have been synthesized via a template-free hydrothermal method. Morphology evolution of the products is determined by the amount of H2C2O4 (oxalic acid) which serves as chelating agent. Structural features of the products were characterized by X-ray diffraction (XRD), and morphology was investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). In addition, the porous structure was analyzed using the Brunauer-Emmett-Teller (BET) approach. The synthesis mechanism of the products with self-assembled hierarchical structures was proposed. The NO2 gas sensing properties of self-assembled hierarchical WO3 HS materials were investigated, the gas sensing properties of WO3 synthesized by a variety of formulations were compared, and the possible gas sensing mechanism was discussed. The obvious enhancement of the gas sensing properties was ascribed to the structure of the hierarchical HS.

  10. Characterizing Surface Acidic Sites in Mesoporous-Silica-Supported Tungsten Oxide Catalysts Using Solid State NMR and Quantum Chemistry Calculations

    SciTech Connect

    Hu, Jian Z.; Kwak, Ja Hun; Wang, Yong; Hu, Mary Y.; Turcu, Romulus VF; Peden, Charles HF

    2011-10-18

    The acidic sites in dispersed tungsten oxide supported on SBA-15 mesoporous silica were investigated using a combination of pyridine titration, both fast-, and slow-MAS {sup 15}N NMR, static {sup 2}H NMR, and quantum chemistry calculations. It is found that the bridged acidic -OH groups in surface adsorbed tungsten dimers (i.e., W-OH-W) are the Broensted acid sites. The unusually strong acidity of these Broensted acid sites is confirmed by quantum chemistry calculations. In contrast, terminal W-OH sites are very stable and only weakly acidic as are terminal Si-OH sites. Furthermore, molecular interactions between pyridine molecules and the dimer Broensted and terminal W-OH sites for dispersed tungsten oxide species is strong. This results in restricted molecular motion for the interacting pyridine molecules even at room temperature, i.e., a reorientation mainly about the molecular 2-fold axis. This restricted reorientation makes it possible to estimate the relative ratio of the Broensted (tungsten dimer) to the weakly acidic terminal W-OH sites in the catalyst using the slow-MAS {sup 1}H-{sup 15}N CP PASS method.

  11. Characterization of Tungsten Oxide Thin Films Produced by Spark Ablation for NO2 Gas Sensing.

    PubMed

    Isaac, Nishchay A; Valenti, Marco; Schmidt-Ott, Andreas; Biskos, George

    2016-02-17

    Tungsten oxides (WOx) thin films are currently used in electro-chromic devices, solar-cells and gas sensors as a result of their versatile and unique characteristics. In this study, we produce nanoparticulate WOx films by spark ablation and focused inertial deposition, and demonstrate their application for NO2 sensing. The primary particles in the as-deposited film samples are amorphous with sizes ranging from 10 to 15 nm. To crystallize the samples, the as-deposited films are annealed at 500 °C in air. This also caused the primary particles to grow to 30-50 nm by sintering. The morphologies and crystal structures of the resulting materials are studied using scanning and transmission electron microscopy and X-ray diffraction, whereas information on composition and oxidation states are determined by X-ray photoemission spectroscopy. The observed sensitivity of the resistance of the annealed films is ∼100 when exposed to 1 ppm of NO2 in air at 200 °C, which provides a considerable margin for employing them in gas sensors for measuring even lower concentrations. The films show a stable and repeatable response pattern. Considering the numerous advantages of spark ablation for fabricating nanoparticulate thin films, the results reported here provide a promising first step toward the production of high sensitivity and high accuracy sensors. PMID:26796099

  12. Characterization of Tungsten Oxide Thin Films Produced by Spark Ablation for NO2 Gas Sensing.

    PubMed

    Isaac, Nishchay A; Valenti, Marco; Schmidt-Ott, Andreas; Biskos, George

    2016-02-17

    Tungsten oxides (WOx) thin films are currently used in electro-chromic devices, solar-cells and gas sensors as a result of their versatile and unique characteristics. In this study, we produce nanoparticulate WOx films by spark ablation and focused inertial deposition, and demonstrate their application for NO2 sensing. The primary particles in the as-deposited film samples are amorphous with sizes ranging from 10 to 15 nm. To crystallize the samples, the as-deposited films are annealed at 500 °C in air. This also caused the primary particles to grow to 30-50 nm by sintering. The morphologies and crystal structures of the resulting materials are studied using scanning and transmission electron microscopy and X-ray diffraction, whereas information on composition and oxidation states are determined by X-ray photoemission spectroscopy. The observed sensitivity of the resistance of the annealed films is ∼100 when exposed to 1 ppm of NO2 in air at 200 °C, which provides a considerable margin for employing them in gas sensors for measuring even lower concentrations. The films show a stable and repeatable response pattern. Considering the numerous advantages of spark ablation for fabricating nanoparticulate thin films, the results reported here provide a promising first step toward the production of high sensitivity and high accuracy sensors.

  13. Thermal annealing and exposure to divertor-like deuterium plasma of tailored tungsten oxide coatings

    NASA Astrophysics Data System (ADS)

    Pezzoli, A.; Dellasega, D.; Russo, V.; Gallo, A.; Zeijlmans van Emmichoven, P. A.; Passoni, M.

    2015-08-01

    In this work we produced tungsten (W) and W oxide (WOx) films by pulsed laser deposition (PLD) with the aim of the addressing modifications of structure and morphology that occur after annealing treatments and high-flux deuterium plasma. Thanks to the high flexibility of PLD we produced nanostructured W containing non-bounded oxygen, different types of WOx and multilayered films. W coatings are dense, non-porous and exhibit a nanocrystalline structure, resembling the coatings used as first wall in tokamaks. The oxide films are nearly stoichiometric amorphous WOx (x = 3) with different morphology from compact to porous. Depending on annealing temperature, nucleation of different crystalline phases (e.g. WO3, W18O49) occurs. Exposure of films to high-flux (∼1024 m-2 s-1) deuterium plasmas in Magnum-PSI at different surface temperatures (Tmax = 580 K) determines material modifications at the nanoscale (e.g. nanometric defects) but no delamination. In addition preliminary deuterium retention results are reported.

  14. Multi-scale Model of Residual Strength of 2D Plain Weave C/SiC Composites in Oxidation Atmosphere

    NASA Astrophysics Data System (ADS)

    Chen, Xihui; Sun, Zhigang; Sun, Jianfen; Song, Yingdong

    2016-06-01

    Multi-scale models play an important role in capturing the nonlinear response of woven carbon fiber reinforced ceramic matrix composites. In plain weave carbon fiber/silicon carbon (C/SiC) composites, the carbon fibers and interphases will be oxidized at elevated temperature and the strength of the composite will be degraded when oxygen enters micro-cracks formed in the as-produced parts due to the mismatch in thermal properties between constituents. As a result of the oxidation on fiber surface, fiber shows a notch-like morphology. In this paper, the change rule of fiber notch depth is fitted by circular function. And a multi-scale model based upon the change rule of fiber notch depth is developed to simulate the residual strength and post-oxidation stress-strain curves of the composite. The multi-scale model is able to accurately predict the residual strength and post-oxidation stress-strain curves of the composite. Besides, the simulated residual strength and post-oxidation stress-strain curves of 2D plain weave C/SiC composites in oxidation atmosphere show good agreements with experimental results. Furthermore, the oxidation time and temperature of the composite are investigated to show their influences upon the residual strength and post-oxidation stress-strain curves of plain weave C/SiC composites.

  15. 2D Graphene Oxide Nanosheets as an Adhesive Over-Coating Layer for Flexible Transparent Conductive Electrodes

    NASA Astrophysics Data System (ADS)

    Moon, In Kyu; Kim, Jae Il; Lee, Hanleem; Hur, Kangheon; Kim, Woon Chun; Lee, Hyoyoung

    2013-01-01

    In recent, highly transparent and flexible, two-dimensional (2D) graphene oxide (GO) nanosheet has been paid attention for various applications. Due to an existence of a large amount of oxygen functional groups, the single 2D GO nanosheet has an insulating, transparent, highly dispersible in the eco-friendly water, and hydrophilic property that has strong adhesion to the hydrophilic surface, which will be the best candidate for the use of an over-coating layer (OCL) and protecting layer for a conductive nanowire based indium-free transparent conductive film (TCF). The ultrathin 2D adhesive GO OCL nanosheet is expected to tightly hold silver nanowires (AgNWs), reduce sheet resistance and produce uniform TCF, providing complete solution that simultaneously solves a high haze, low transparency with a conventional OCL and mechanical instability in cases without a thick OCL. Our novel 2D insulating and hydrophilic GO OCL successfully provided a large-area, flexible, and highly transparent AgNW TCF.

  16. Controlled preferential oxidation of grain boundaries in monolayer tungsten disulfide for direct optical imaging.

    PubMed

    Rong, Youmin; He, Kuang; Pacios, Mercè; Robertson, Alex W; Bhaskaran, Harish; Warner, Jamie H

    2015-04-28

    Synthetic 2D crystal films grown by chemical vapor deposition are typically polycrystalline, and determining grain size within domains and continuous films is crucial for determining their structure. Here we show that grain boundaries in the 2D transition metal dichalcogenide WS2, grown by CVD, can be preferentially oxidized by controlled heating in air. Under our developed conditions, preferential degradation at the grain boundaries causes an increase in their physical size due to oxidation. This increase in size enables their clear and rapid identification using a standard optical microscope. We demonstrate that similar treatments in an Ar environment do no show this effect, confirming that oxidation is the main role in the structural change. Statistical analysis of grain boundary (GB) angles shows dominant mirror formation. Electrical biasing across the GB is shown to lead to changes at the GB and their observation under an optical microscope. Our approach enables high-throughput screening of as-synthesized WS2 domains and continuous films to determine their crystallinity and should enable improvements in future CVD growth of these materials.

  17. Kinetics and mechanisms of oxidation of 2D woven C/SiC composites; 1: Experimental approach

    SciTech Connect

    Lamouroux, F.; Camus, G. . Lab. des Composites Thermostructuraux); Thebault, J. )

    1994-08-01

    The oxidation behavior of a 2D woven C/SiC composite partly protected with a SiC seal coating and heat-treated (stabilized) at 1,600 C in inert gas has been investigated through an experimental approach based on thermogravimetric analyses and optical/electron microscopy. Results of the tests, performed under flowing oxygen, have shown that the oxidation behavior of the composite material in terms of oxidation kinetics and morphological evolutions is related to the presence of thermal microcracks in the seal coating as well as in the matrix. Three different temperature domains exist. At low temperatures (< 800 C), the mechanisms of reaction between carbon and oxygen control the oxidation kinetics and are associated with a uniform degradation of the carbon reinforcement. At intermediate temperatures, (between 800 and 1,100 C), the oxidation kinetics are controlled by the gas-phase diffusion through a network of microcracks in the SiC coatings, resulting in a nonuniform degradation of the carbon phases. At high temperatures (> 1,100 C), such diffusion mechanisms are limited by sealing of the microcracks by silica; therefore, the degradation of the composite remains superficial. The study of the oxidation behavior of (i) the heat-treated composite in a lower oxygen content environment (dry air) and (ii) the as-processed (unstabilized) composite in dry oxygen confirms the different mechanisms proposed to explain the oxidation behavior of the composite material.

  18. Chemical downstream etching of tungsten

    SciTech Connect

    Blain, M.G.; Jarecki, R.L.; Simonson, R.J.

    1998-07-01

    The downstream etching of tungsten and tungsten oxide has been investigated. Etching of chemical vapor deposited tungsten and e-beam deposited tungsten oxide samples was performed using atomic fluorine generated by a microwave discharge of argon and NF{sub 3}. Etching was found to be highly activated with activation energies approximated to be 6.0{plus_minus}0.5thinspkcal/mol and 5.4{plus_minus}0.4thinspkcal/mol for W and WO{sub 3}, respectively. In the case of F etching of tungsten, the addition of undischarged nitric oxide (NO) directly into the reaction chamber results in the competing effects of catalytic etch rate enhancement and the formation of a nearly stoichiometric WO{sub 3} passivating tungsten oxide film, which ultimately stops the etching process. For F etching of tungsten oxide, the introduction of downstream NO reduces the etch rate. {copyright} {ital 1998 American Vacuum Society.}

  19. Optimization of substrate-target distance for pulsed laser deposition of tungsten oxide thin films using Langmuir probe

    NASA Astrophysics Data System (ADS)

    Panda, A. Kumar; Singh, A.; Thirumurugesan, R.; Kuppusami, P.; Mohandas, E.

    2015-09-01

    The paper investigates the spatial and temporal variation of laser produced plasma of tungsten oxide using a Langmuir probe. The plasma was produced by laser ablation of tungsten oxide target using an Excimer laser of wavelength 248 nm. Our experimental studies confirmed that oxygen partial pressure (P) of 2× 10-2 mbar is sufficient enough to get stoichiometric tungsten oxide thin films and the plume dynamics was diagnosed for their spatial and temporal behaviour at the above optimised oxygen pressure. Spatial distribution was recorded with the target to substrate distance (D) ranging from the target position to a distance of 75 mm away from the target, whereas the temporal variation was taken in the range of 0-50 μ S with an interval of 0.5 μ S. The average electron densities were found to be maximum at 30 mm from the target position. However, ion density was constant beyond the probe distance of 45 mm from the target. The plasma current was found to be maximum at 28 μ S. The target to substrate distance was optimized for homogenous adherent good quality thin films using plasma parameters such as ion density and average electron density obtained at different oxygen pressure. The target distance and background gas pressure were correlated as PD scaling law and fitted as PD3 in the model.

  20. Evaporation-Induced Self-Assembly of Ultrathin Tungsten Oxide Nanowires over a Large Scale for Ultraviolet Photodetector.

    PubMed

    Cheng, Wei; Niederberger, Markus

    2016-03-15

    Self-assembly of inorganic nanowires on a large scale directly on a substrate represents a great challenge. Starting from colloidally stable dispersions of ultrathin tungsten oxide nanowires, we successfully assemble the nanowires on a centimeter scale on flat or patterned substrates by a simple evaporation-induced self-assembly method. The capillary flow generated during the evaporation is responsible for the assembly of the nanowires. The concentration of the nanowire dispersion has a significant influence on the self-assembly behavior. Well-aligned tungsten oxide nanowire thin films are achieved when the concentration of the dispersion is in the range from 0.5 to 3.0 mg/mL. While at higher concentrations disordered nanowire thin films with cracks are formed, lower concentrations do not result in the formation of a continuous thin film. A macroscopic device based on the self-assembled tungsten oxide nanowires is fabricated, exhibiting good performance for UV light detection. Our results may pave the road for integrating aligned ultrathin semiconductor nanowires into macroscopic devices for optoelectronic applications. PMID:26900019

  1. Trace H2 O2 -Assisted High-Capacity Tungsten Oxide Electrochromic Batteries with Ultrafast Charging in Seconds.

    PubMed

    Zhao, Jinxiong; Tian, Yuyu; Wang, Zhen; Cong, Shan; Zhou, Di; Zhang, Qingzhu; Yang, Mei; Zhang, Weikun; Geng, Fengxia; Zhao, Zhigang

    2016-06-13

    A recent technological trend in the field of electrochemical energy storage is to integrate energy storage and electrochromism functions in one smart device, which can establish efficient user-device interactions based on a friendly human-readable output. This type of newly born energy storage technology has drawn tremendous attention. However, there is still plenty of room for technological and material innovation, which would allow advancement of the research field. A prototype Al-tungsten oxide electrochromic battery with interactive color-changing behavior is reported. With the assistance of trace amount of H2 O2 , the battery exhibits a specific capacity almost seven times that for the reported electrochromic batteries, up to 429 mAh g(-1) . Fast decoloration of the reduced tungsten oxide affords a very quick charging time of only eight seconds, which possibly comes from an intricate combination of structure and valence state changes of tungsten oxide. This unique combination of features may further advance the development of smart energy storage devices with suitability for user-device interactions.

  2. Trace H2 O2 -Assisted High-Capacity Tungsten Oxide Electrochromic Batteries with Ultrafast Charging in Seconds.

    PubMed

    Zhao, Jinxiong; Tian, Yuyu; Wang, Zhen; Cong, Shan; Zhou, Di; Zhang, Qingzhu; Yang, Mei; Zhang, Weikun; Geng, Fengxia; Zhao, Zhigang

    2016-06-13

    A recent technological trend in the field of electrochemical energy storage is to integrate energy storage and electrochromism functions in one smart device, which can establish efficient user-device interactions based on a friendly human-readable output. This type of newly born energy storage technology has drawn tremendous attention. However, there is still plenty of room for technological and material innovation, which would allow advancement of the research field. A prototype Al-tungsten oxide electrochromic battery with interactive color-changing behavior is reported. With the assistance of trace amount of H2 O2 , the battery exhibits a specific capacity almost seven times that for the reported electrochromic batteries, up to 429 mAh g(-1) . Fast decoloration of the reduced tungsten oxide affords a very quick charging time of only eight seconds, which possibly comes from an intricate combination of structure and valence state changes of tungsten oxide. This unique combination of features may further advance the development of smart energy storage devices with suitability for user-device interactions. PMID:27159245

  3. Synthesis of Nanodispersed Oxides of Vanadium, Titanium, Molybdenum, and Tungsten on Mesoporous Silica using Atomic Layer Deposition

    SciTech Connect

    Herrera, Jose E.; Kwak, Ja Hun; Hu, Jian Zhi; Wang, Yong; Peden, Charles HF

    2006-10-01

    The advantages of the atomic layer deposition (ALD) method for preparation of tungsten, vanadium, titanium and molybdenum oxide catalyst supported on mesoporous silica are discussed, with emphasis on the importance of synthesis conditions on dispersion, structure and activity of the resulting materials. A suite of complementary techniques such as DRS-UV/Vis, BET, 1H-NMR, XRD, and TEM were used to study the structural properties of the supported metal oxides, and probe reactions such as 2-butanol dehydration and ethanol partial oxidation were used to demonstrate the potential advantages of the ALD prepared catalysts. Specifically, highly dispersed oxides of titanium, molybdenum, and tungsten oxide on mesoporous silica were synthesized using the ALD method. It is also demonstrated that attainment of high dispersions of vanadium oxide on mesoporous silica requires the presence of at least a single layer of titanium oxide due to the well-known poor interaction between vanadia and silica. The highly dispersed catalysts prepared here by ALD methods exhibited superior catalytic performance relative to those prepared using conventional incipient wetness impregnation.

  4. Two-dimensional (2D) Chemiluminescence (CL) correlation spectroscopy for studying thermal oxidation of isotactic polypropylene (iPP)

    NASA Astrophysics Data System (ADS)

    Shinzawa, Hideyuki; Hagihara, Hideaki; Suda, Hiroyuki; Mizukado, Jyunji

    2016-11-01

    Application of the two-dimensional (2D) correlation spectroscopy is extended to Chemiluminescence (CL) spectra of isotactic polypropylene (iPP) under thermally induced oxidation. Upon heating, the polymer chains of the iPP undergoes scissoring and fragmentation to develop several intermediates. While different chemical species provides the emission at different wavelength regions, entire feature of the time-dependent CL spectra of the iPP samples were complicated by the presence of overlapped contributions from singlet oxygen (1O2) and carbonyl species within sample. 2D correlation spectra showed notable enhancement of the spectral resolution to provide penetrating insight into the thermodynamics of the polymer system. For example, the, oxidation induce scissoring and fragmentation of the polymer chains to develop the carbonyl group. Further reaction results in the consumption of the carbonyl species and subsequent production of different 1O2 species each developed in different manner. Consequently, key information on the thermal oxidation can be extracted in a surprisingly simple manner without any analytical expression for the actual response curves of spectral intensity signals during the reaction.

  5. Tungsten oxide (WO{sub 3}) thin films for application in advanced energy systems

    SciTech Connect

    Gullapalli, S. K.; Vemuri, R. S.; Manciu, F. S.; Enriquez, J. L.; Ramana, C. V.

    2010-07-15

    Inherent processes in coal gasification plants produce hazardous hydrogen sulfide (H{sub 2}S), which must be continuously and efficiently detected and removed before the fuel is used for power generation. An attempt has been made in this work to fabricate tungsten oxide (WO{sub 3}) thin films by radio-frequency reactive magnetron-sputter deposition. The impetus being the use of WO{sub 3} films for H{sub 2}S sensors in coal gasification plants. The effect of growth temperature, which is varied in the range of 30-500 deg. C, on the growth and microstructure of WO{sub 3} thin films is investigated. Characterizations made using scanning electron microscopy (SEM) and x-ray diffraction (XRD) indicate that the effect of temperature is significant on the microstructure of WO{sub 3} films. XRD and SEM results indicate that the WO{sub 3} films grown at room temperature are amorphous, whereas films grown at higher temperatures are nanocrystalline. The average grain-size increases with increasing temperature. WO{sub 3} films exhibit smooth morphology at growth temperatures {<=}300 deg. C while relatively rough at >300 deg. C. The analyses indicate that the nanocrystalline WO{sub 3} films grown at 100-300 deg. C could be the potential candidates for H{sub 2}S sensor development for application in coal gasification systems.

  6. Multi-Walled Carbon Nanotube-Doped Tungsten Oxide Thin Films for Hydrogen Gas Sensing

    PubMed Central

    Wongchoosuk, Chatchawal; Wisitsoraat, Anurat; Phokharatkul, Ditsayut; Tuantranont, Adisorn; Kerdcharoen, Teerakiat

    2010-01-01

    In this work we have fabricated hydrogen gas sensors based on undoped and 1 wt% multi-walled carbon nanotube (MWCNT)-doped tungsten oxide (WO3) thin films by means of the powder mixing and electron beam (E-beam) evaporation technique. Hydrogen sensing properties of the thin films have been investigated at different operating temperatures and gas concentrations ranging from 100 ppm to 50,000 ppm. The results indicate that the MWCNT-doped WO3 thin film exhibits high sensitivity and selectivity to hydrogen. Thus, MWCNT doping based on E-beam co-evaporation was shown to be an effective means of preparing hydrogen gas sensors with enhanced sensing and reduced operating temperatures. Creation of nanochannels and formation of p-n heterojunctions were proposed as the sensing mechanism underlying the enhanced hydrogen sensitivity of this hybridized gas sensor. To our best knowledge, this is the first report on a MWCNT-doped WO3 hydrogen sensor prepared by the E-beam method. PMID:22163623

  7. Tungsten Oxide Nanorods: An Efficient Nanoplatform for Tumor CT Imaging and Photothermal Therapy

    PubMed Central

    Zhou, Zhiguo; Kong, Bin; Yu, Chao; Shi, Xiangyang; Wang, Mingwei; Liu, Wei; Sun, Yanan; Zhang, Yingjian; Yang, Hong; Yang, Shiping

    2014-01-01

    We report here a facile thermal decomposition approach to creating tungsten oxide nanorods (WO2.9 NRs) with a length of 13.1 ± 3.6 nm and a diameter of 4.4 ± 1.5 nm for tumor theranostic applications. The formed WO2.9 NRs were modified with methoxypoly(ethylene glycol) (PEG) carboxyl acid via ligand exchange to have good water dispersability and biocompatibility. With the high photothermal conversion efficiency irradiated by a 980 nm laser and the better X-ray attenuation property than clinically used computed tomography (CT) contrast agent Iohexol, the formed PEGylated WO2.9 NRs are able to inhibit the growth of the model cancer cells in vitro and the corresponding tumor model in vivo, and enable effective CT imaging of the tumor model in vivo. Our “killing two birds with one stone” strategy could be extended for fabricating other nanoplatforms for efficient tumor theranostic applications. PMID:24413483

  8. Investigation into the optoelectrical properties of tungsten oxide thin films annealed in an oxygen air

    SciTech Connect

    Arfaoui, A.; Ouni, B. Touihri, S.; Mannoubi, T.

    2014-12-15

    Tungsten oxide (WO{sub x}) thin film have been deposited onto glass substrates using the thermal vacuum evaporation technique, monitored by an annealing process in a variable oxygen atmosphere. Analysis by X-ray diffraction and Raman spectroscopy showed the structural changes from orthorhombic to monoclinic which depend on the annealing temperature and the oxygen content. AFM study shows that the increase of oxygen content leads to a decrease of the root-mean-square from 94.64 nm to 2 nm. Ellipsometric measurements have been used to evaluate the optical constants. Further, it is found that when the oxygen content increases, the band gap of the annealed layer varies from 3.01 eV to 3.52 eV by against, the Urbach energy decreases. The AC conductivity plot showed a universal power law according to the Jonscher model. Moreover, at high frequency semiconductor-to-metallic behavior has been observed. Finally, the effect of annealing in oxygen atmosphere on their structural modifications, morphological, optical properties and electrical conductivity are reported.

  9. Stability of the anodic growth porous tungsten oxide in different solutions

    SciTech Connect

    Chai, Y.; Yam, F. K.; Hassan, Z.

    2015-05-15

    This article presents the study of the stability of the anodic growth porous tungsten oxide (WO{sub 3}) film in different solutions. As-anodized films are relatively stable in acidic electrolytes like sulphuric acid (H{sub 2}SO{sub 4}), hydrochloric acid (HCl) but not in oxalic acid. In higher pH solution, rate of dissolution of the WO{sub 3} film is higher. Annealing at 400 °C for 2 h transform the as-grown sample from amorphous phase to the crystalline phase and this significantly improve the stability of the film in high pH solution. Photocurrent measurements reveal that there is no significant difference of the electrolyte used (0.5 M H{sub 2}SO{sub 4}, 0.33 M H{sub 3}PO{sub 4}, 0.1 M sodium sulfate (Na{sub 2}SO{sub 4})) on the photocurrent. As-annealed films exhibit good stablility for the long photoelectrochemical (PEC) measurements (1700 s) in 0.5 M H{sub 2}SO{sub 4} and 0.1 M Na{sub 2}SO{sub 4}. There is no effect on the photocurrent for the variation of the concentration of the acidic solution (H{sub 2}SO{sub 4}). However, lower photocurrent was obtained as the concentration of Na{sub 2}SO{sub 4} was increased.

  10. Origin of ferroelectric polarization in tetragonal tungsten-bronze-type oxides

    NASA Astrophysics Data System (ADS)

    Olsen, Gerhard Henning; Aschauer, Ulrich; Spaldin, Nicola A.; Selbach, Sverre Magnus; Grande, Tor

    2016-05-01

    The origin of ferroelectric polarization in tetragonal tungsten-bronze- (TTB-) type oxide strontium barium niobate (SBN) is investigated using first-principles density functional calculations. We study in particular the relationship between the polarization and the cation and vacancy ordering on alkali-earth metal lattice sites. Lattice dynamical calculations for paraelectric structures demonstrate that all cation configurations that can be accommodated in a 1 ×1 ×2 supercell result in a single unstable polar phonon, composed primarily of relative Nb-O displacements along the polar axis, as their dominant instability. The majority of the configurations also have a second octahedral tilt-mode instability which couples weakly to the polar mode. The existence of the tilt mode is strongly dependent on the local cation ordering, consistent with the fact that it is not found experimentally. Our results suggest that ferroelectricity in the SBN system is driven by a conventional second-order Jahn-Teller mechanism caused by the d0 Nb5 + cations, and demonstrate the strong influence of the size of Sr and Ba on the lattice distortions associated with polarization and octahedral tilting. Finally, we suggest a mechanism for the relaxor behavior in Sr-rich SBN based on Sr displacement inside pentagonal channels in the TTB structure.

  11. Photochromic Properties of Tungsten Oxide/Methylcellulose Composite Film Containing Dispersing Agents.

    PubMed

    Yamazaki, Suzuko; Ishida, Hiroki; Shimizu, Dai; Adachi, Kenta

    2015-12-01

    Tungsten oxide-based photochromic films which changed reversibly in air between colorless- transparent in the dark and dark blue under UV irradiation were prepared by using methylcellulose as a film matrix and polyols such as ethylene glycol (EG), propylene glycol (PG), and glycerin (Gly) as dispersing agents. Influence of the dispersing agents and water in the films on the photochromic behavior was systematically studied. Under UV irradiation, absorption bands around 640 and 980 nm increased and the coloring rate was the following order: Gly > EG > PG. An increase in the amounts of dispersing agents or water accelerated the coloring rate. By increasing the water content of the film, a new absorption peak appeared at ca. 775 nm and the Raman spectra indicated a shift of W-O-W stretching vibration to lower wavenumber which was due to the formation of hydrogen bonding. All absorption spectra were fit by three Lorentz functions, whose bands were ascribed to various packing of WO6 octahedra. After the light was turned off, the formation of W(5+) was stopped and bleaching occurred by the reaction with O2 in air to recover its original transparent state. We anticipate that the biodegradable photochromic films developed in this study can be applied in recyclable display medium and especially in detachable films for glass windows whose light transmission properties are changed by sunlight, i.e., for usage as an alternative of smart windows without applying voltage. PMID:26552031

  12. Hierarchical structured tungsten oxide nanocrystals via hydrothermal route: microstructure, formation mechanism and humidity sensing

    NASA Astrophysics Data System (ADS)

    Pang, Hua-Feng; Li, Zhi-Jie; Xiang, Xia; Fu, Yong-Qing; Placido, Frank; Zu, Xiao-Tao

    2013-09-01

    Hierarchical structured tungsten oxide nanocrystals were synthesized via the hydrothermal route assisted by a capping agent of ammonium benzoate (AB). The products were characterized using scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and transmission electron microscopy. The experimental results show that the crystal microstructures could be changed from flower-shape to star-shape by changing the mole ratio of ammonium benzoate to sodium tungstate (AB/ST). The crystal phases were changed from orthorhombic WO3ṡ0.33H2O to hexagonal WO3 with the increase in the concentration of AB. Based on the results from Fourier transform infrared spectroscopy and time-dependent growth analysis, a self-assembly growth mechanism has been proposed for the formation of flower, spherical, and star-netted microstructures at different mole ratios of the AB/ST. The star-netted WO3 nanocrystals were applied as a sensitive layer for humidity sensing performed using a Love-mode ZnO/36∘ Y-cut LiTaO3 surface acoustic wave device, and a stable and sensitive response to the change of relative humidity was obtained.

  13. Molybdenum disulfide catalyzed tungsten oxide for on-chip acetone sensing

    NASA Astrophysics Data System (ADS)

    Li, Hong; Ahn, Sung Hoon; Park, Sangwook; Cai, Lili; Zhao, Jiheng; He, Jiajun; Zhou, Minjie; Park, Joonsuk; Zheng, Xiaolin

    2016-09-01

    Acetone sensing is critical for acetone leak detection and holds a great promise for the noninvasive diagnosis of diabetes. It is thus highly desirable to develop a wearable acetone sensor that has low cost, miniature size, sub-ppm detection limit, great selectivity, as well as low operating temperature. In this work, we demonstrate a cost-effective on-chip acetone sensor with excellent sensing performances at 200 °C using molybdenum disulfide (MoS2) catalyzed tungsten oxide (WO3). The WO3 based acetone sensors are first optimized via combined mesoscopic nanostructuring and silicon doping. Under the same testing conditions, our optimized mesoporous silicon doped WO3 [Si:WO3(meso)] sensor shows 2.5 times better sensitivity with ˜1000 times smaller active device area than the state-of-art WO3 based acetone sensor. Next, MoS2 is introduced to catalyze the acetone sensing reactions for Si:WO3(meso), which reduces the operating temperature by 100 °C while retaining its high sensing performances. Our miniaturized acetone sensor may serve as a wearable acetone detector for noninvasive diabetes monitoring or acetone leakage detection. Moreover, our work demonstrates that MoS2 can be a promising nonprecious catalyst for catalytic sensing applications.

  14. Morphological and Phase Controlled Tungsten Based Nanoparticles: Synthesis and Characterization of Scheelites, Wolframites, and Oxides Nanomaterials

    PubMed Central

    Hernandez-Sanchez, Bernadette A.; Boyle, Timothy J.; Pratt, Harry D.; Rodriguez, Mark A.; Brewer, Luke N.; Dunphy, Darren R.

    2009-01-01

    For the first time tungsten based nanoparticles (WNPs) of scheelite (MWO4; M = Ca, Sr, Ba, Pb), wolframite (MWO4; M = Mn, Fe, Zn & (Mg0.60Mn0.17Fe0.26)WO4), and the oxide (WO3 and W18O49) were synthesized from solution precipitation (i.e.,trioctylamine or oleic acid) and solvothermal (i.e., benzyl alcohol) routes. The resultant WNPs were prepared directly from tungsten (VI) ethoxide (W(OCH2CH3)6, 1) and stoichiometeric mixtures of the following precursors: [Ca(N(SiMe3)2)2]2 (2), Pb(N(SiMe3)2)2 (3), Mn[(μ-Mes)2Mn(Mes)]2 (4), [Fe(μ-Mes)(Mes)]2 (5), Fe(CO)5 (6), H+[Ba2(μ3-ONep)(μ-ONep)2(ONep)(ONep)3(py)]−2 (7), H+[Sr5(μ4-O)(μ3-ONep)4(μ-ONep)4(ONep)(py)4]− (8), and [Zn(Et)(ONep)(py)]2 (9) where Mes = C6H2(CH3)3-2,4,6, ONep = OCH2CMe3, Et = CH2CH3, and py = pyridine. Through these routes, the WNP morphologies were found to be manipulated by the processing conditions, while precursor selection influenced the final phase observed. For the solution precipitation route, 1 yielded (5 × 100 nm) W18O49 rods while stochiometeric reactions between 1 and (2 – 9) generated homogenous sub 30 nm nano-dots, -diamonds, -rods, and -wires for the MWO4 systems. For the solvothermal route, 1 was found to produce wires of WO3 with aspect ratios of 20 while (1 & 2) formed 10 – 60 nm CaWO4 nanodots. Room temperature photoluminescent (PL) emission properties of select WNPs were also examined with fluorescence spectroscopy (λex = 320 nm). Broad PL emissions = 430, 420, 395, 420 nm were noted for 5 × 100 nm W18O49 rods, 5 × 15 nm, CaWO4 rods, 10 – 30 nm CaWO4 dots, and 10 nm BaWO4 diamonds, respectively. PMID:19911034

  15. Tungsten coatings electro-deposited on CFC substrates from oxide molten salt

    NASA Astrophysics Data System (ADS)

    Sun, Ningbo; Zhang, Yingchun; Lang, Shaoting; Jiang, Fan; Wang, Lili

    2014-12-01

    Tungsten is considered as plasma facing material in fusion devices because of its high melting point, its good thermal conductivity, its low erosion rate and its benign neutron activation properties. On the other hand, carbon based materials like C/C fiber composites (CFC) have been used for plasma facing materials (PFMs) due to their high thermal shock resistance, light weight and high strength. Tungsten coatings on CFC substrates are used in the JET divertor in the frame of the JET ITER-like wall project, and have been prepared by plasma spray (PS) and other techniques. In this study, tungsten coatings were electro-deposited on CFC from Na2WO4-WO3 molten salt under various deposition parameters at 900 °C in air. In order to obtain tungsten coatings with excellent performance, the effects of pulse duration ratio and pulse current density on microstructures and crystal structures of tungsten coatings were investigated by X-ray diffraction (XRD, Rigaku Industrial Co., Ltd., D/MAX-RB) and a scanning electron microscope (SEM, JSM 6480LV). It is found that the pulsed duration ratio and pulse current density had a significant influence on tungsten nucleation and electro-crystallization phenomena. SEM observation revealed that intact, uniform and dense tungsten coatings formed on the CFC substrates. Both the average grain size and thickness of the coating increased with the pulsed current density. The XRD results showed that the coatings consisted of a single phase of tungsten with the body centered cubic (BCC) structure. The oxygen content of electro-deposited tungsten coatings was lower than 0.05%, and the micro-hardness was about 400 HV.

  16. Mechanical characterisation of tungsten-1 wt.% yttrium oxide as a function of temperature and atmosphere

    NASA Astrophysics Data System (ADS)

    Palacios, T.; Jiménez, A.; Muñóz, A.; Monge, M. A.; Ballesteros, C.; Pastor, J. Y.

    2014-11-01

    This study evaluates the mechanical behaviour of an Y2O3-dispersed tungsten (W) alloy and compares it to a pure W reference material. Both materials were processed via mechanical alloying (MA) and subsequent hot isostatic pressing (HIP). We performed non-standard three-point bending (TPB) tests in both an oxidising atmosphere and vacuum across a temperature range from 77 K, obtained via immersion in liquid nitrogen, to 1473 K to determine the mechanical strength, yield strength and fracture toughness. This research aims to evaluate how the mechanical behaviour of the alloy is affected by oxides formed within the material at high temperatures, primarily from 873 K, when the materials undergo a massive thermal degradation. The results indicate that the alloy is brittle to a high temperature (1473 K) under both atmospheres and that the mechanical properties degrade significantly above 873 K. We also used Vickers microhardness tests and the dynamic modulus by impulse excitation technique (IET) to determine the elastic modulus at room temperature. Moreover, we performed nanoindentation tests to determine the effect of size on the hardness and elastic modulus; however, no significant differences were found. Additionally, we calculated the relative density of the samples to assess the porosity of the alloy. Finally, we analysed the microstructure and fracture surfaces of the tested materials via field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). In this way, the relationship between the macroscopic mechanical properties and micromechanisms of failure could be determined based on the temperature and oxides formed.

  17. Oxide 2D electron gases as a route for high carrier densities on (001) Si

    SciTech Connect

    Kornblum, Lior; Jin, Eric N.; Kumah, Divine P.; Walker, Fred J.; Ernst, Alexis T.; Broadbridge, Christine C.; Ahn, Charles H.

    2015-05-18

    Two dimensional electron gases (2DEGs) formed at the interfaces of oxide heterostructures draw considerable interest owing to their unique physics and potential applications. Growing such heterostructures on conventional semiconductors has the potential to integrate their functionality with semiconductor device technology. We demonstrate 2DEGs on a conventional semiconductor by growing GdTiO{sub 3}-SrTiO{sub 3} on silicon. Structural analysis confirms the epitaxial growth of heterostructures with abrupt interfaces and a high degree of crystallinity. Transport measurements show the conduction to be an interface effect, ∼9 × 10{sup 13} cm{sup −2} electrons per interface. Good agreement is demonstrated between the electronic behavior of structures grown on Si and on an oxide substrate, validating the robustness of this approach to bridge between lab-scale samples to a scalable, technologically relevant materials system.

  18. Bandgap Engineering of Phosphorene by Laser Oxidation toward Functional 2D Materials.

    PubMed

    Lu, Junpeng; Wu, Jing; Carvalho, Alexandra; Ziletti, Angelo; Liu, Hongwei; Tan, Junyou; Chen, Yifan; Castro Neto, A H; Özyilmaz, Barbaros; Sow, Chorng Haur

    2015-10-27

    We demonstrate a straightforward and effective laser pruning approach to reduce multilayer black phosphorus (BP) to few-layer BP under ambient condition. Phosphorene oxides and suboxides are formed and the degree of laser-induced oxidation is controlled by the laser power. Since the band gaps of the phosphorene suboxide depend on the oxygen concentration, this simple technique is able to realize localized band gap engineering of the thin BP. Micropatterns of few-layer phosphorene suboxide flakes with unique optical and fluorescence properties are created. Remarkably, some of these suboxide flakes display long-term (up to 2 weeks) stability in ambient condition. Comparing against the optical properties predicted by first-principle calculations, we develop a "calibration" map in using focused laser power as a handle to tune the band gap of the BP suboxide flake. Moreover, the surface of the laser patterned region is altered to be sensitive to toxic gas by way of fluorescence contrast. Therefore, the multicolored display is further demonstrated as a toxic gas monitor. In addition, the BP suboxide flake is demonstrated to exhibit higher drain current modulation and mobility comparable to that of the pristine BP in the electronic application.

  19. Gas nanosensor design packages based on tungsten oxide: mesocages, hollow spheres, and nanowires

    NASA Astrophysics Data System (ADS)

    Hoa, Nguyen Duc; El-Safty, Sherif A.

    2011-12-01

    Achieving proper designs of nanosensors for highly sensitive and selective detection of toxic environmental gases is one of the crucial issues in the field of gas sensor technology, because such designs can lead to the enhancement of gas sensor performance and expansion of their applications. Different geometrical designs of porous tungsten oxide nanostructures, including the mesocages, hollow spheres and nanowires, are synthesized for toxic gas sensor applications. Nanosensor designs with small crystalline size, large specific surface area, and superior physical characteristics enable the highly sensitive and selective detection of low concentration (ppm levels), highly toxic NO2 among CO, as well as volatile organic compound gases, such as acetone, benzene, and ethanol. The experimental results showed that the sensor response was not only dependent on the specific surface area, but also on the geometries and crystal size of materials. Among the designed nanosensors, the nanowires showed the highest sensitivity, followed by the mesocages and hollow spheres—despite the fact that mesocages had the largest specific surface area of 80.9 m2 g - 1, followed by nanowires (69.4 m2 g - 1), and hollow spheres (6.5 m2 g - 1). The nanowire sensors had a moderate specific surface area (69.4 m2 g - 1) but they exhibited the highest sensitivity because of their small diameter (~5 nm), which approximates the Debye length of WO3. This led to the depletion of the entire volume of the nanowires upon exposure to NO2, resulting in an enormous increase in sensor resistance.

  20. Numerical Modeling of Oxidized 2D C/SiC Composites in Air Environments Below 900 °C: Microstructure and Elastic Properties

    NASA Astrophysics Data System (ADS)

    Sun, Zhigang; Chen, Xihui; Shao, Hongyan; Song, Yingdong

    2016-08-01

    A numerical model is presented for simulation of the oxidation-affected behaviors of two dimensional carbon fiber-reinforced silcon carbide matrix composite (2D C/SiC) exposed to air oxidizing environments below 900 °C, which incorporates the modeling of oxidized microstructure and computing of degraded elastic properties. This model is based upon the analysis of the representative volume cell (RVC) of the composite. The multi-scale model of 2D C/SiC composites is concerned in the present study. Analysis results of such a composite can provide a guideline for the real 2D C/SiC composite. The micro-structure during oxidation process is firstly modeled in the RVC. The elastic moduli of oxidized composite under non-stress oxidation environment is computed by finite element analysis. The elastic properties of 2D-C/SiC composites in air oxidizing environment are evaluated and validated in comparison to experimental data. The oxidation time, temperature and fiber volume fractions of C/SiC composite are investigated to show their influences upon the elastic properties of 2D C/SiC composites.

  1. Development of 2D dynamic model for hydrogen-fed and methane-fed solid oxide fuel cells

    NASA Astrophysics Data System (ADS)

    Luo, X. J.; Fong, K. F.

    2016-10-01

    A new two-dimensional (2D) dynamic model is developed in Fortran to study the mass and energy transport, the velocity field and the electrochemical phenomena of high-temperature solid oxide fuel cell (SOFC). The key feature of this model is that gas properties, reaction heat, open circuit voltage, ohmic voltage and exchange current density are temperature-dependent. Based on this, the change of gas temperature and related characteristics can be evaluated in this study. The transient performances of SOFC, like heat-up and start-up processes, are therefore assessed accordingly. In this 2D dynamic SOFC model, chemical and electrochemical reaction, flow field, mass and energy transfer models are coupled in order to determine the current density, the mass fraction and the temperature of gas species. Mass, momentum and energy balance equations are discretized by finite difference method. Performance evaluation in current density, electrical efficiency and overall efficiency is conducted for the effects of different operating parameters in SOFC. The present model can serve as a valuable tool for in-depth performance evaluation of other design and operating parameters of SOFC unit, as well as further dynamic simulation and optimization of SOFC as a prime mover in cogeneration or trigeneration system.

  2. Superparamagnetic iron oxide nanoparticles alter expression of obesity and T2D-associated risk genes in human adipocytes

    PubMed Central

    Sharifi, S.; Daghighi, S.; Motazacker, M. M.; Badlou, B.; Sanjabi, B.; Akbarkhanzadeh, A.; Rowshani, A. T.; Laurent, S.; Peppelenbosch, M. P.; Rezaee, F.

    2013-01-01

    Adipocytes hypertrophy is the main cause of obesity and its affliction such as type 2 diabetes (T2D). Since superparamagnetic iron oxide nanoparticles (SPIONs) are used for a wide range of biomedical/medical applications, we aimed to study the effect of SPIONs on 22 and 29 risk genes (Based on gene wide association studies) for obesity and T2D in human adipocytes. The mRNA expression of lipid and glucose metabolism genes was changed upon the treatment of human primary adipocytes with SPIONs. mRNA of GULP1, SLC30A8, NEGR1, SEC16B, MTCH2, MAF, MC4R, and TMEM195 were severely induced, whereas INSIG2, NAMPT, MTMR9, PFKP, KCTD15, LPL and GNPDA2 were down-regulated upon SPIONs stimulation. Since SEC16B gene assist the phagocytosis of apoptotic cells and this gene were highly expressed upon SPIONs treatment in adipocytes, it is logic to assume that SPIONs may play a crucial role in this direction, which requires more consideration in the future. PMID:23838847

  3. Superparamagnetic iron oxide nanoparticles alter expression of obesity and T2D-associated risk genes in human adipocytes

    NASA Astrophysics Data System (ADS)

    Sharifi, S.; Daghighi, S.; Motazacker, M. M.; Badlou, B.; Sanjabi, B.; Akbarkhanzadeh, A.; Rowshani, A. T.; Laurent, S.; Peppelenbosch, M. P.; Rezaee, F.

    2013-07-01

    Adipocytes hypertrophy is the main cause of obesity and its affliction such as type 2 diabetes (T2D). Since superparamagnetic iron oxide nanoparticles (SPIONs) are used for a wide range of biomedical/medical applications, we aimed to study the effect of SPIONs on 22 and 29 risk genes (Based on gene wide association studies) for obesity and T2D in human adipocytes. The mRNA expression of lipid and glucose metabolism genes was changed upon the treatment of human primary adipocytes with SPIONs. mRNA of GULP1, SLC30A8, NEGR1, SEC16B, MTCH2, MAF, MC4R, and TMEM195 were severely induced, whereas INSIG2, NAMPT, MTMR9, PFKP, KCTD15, LPL and GNPDA2 were down-regulated upon SPIONs stimulation. Since SEC16B gene assist the phagocytosis of apoptotic cells and this gene were highly expressed upon SPIONs treatment in adipocytes, it is logic to assume that SPIONs may play a crucial role in this direction, which requires more consideration in the future.

  4. Electrospun tungsten oxide NPs/PVA nanofibers: A study on the morphology and Kramers-Kronig analysis of infrared reflectance spectra

    NASA Astrophysics Data System (ADS)

    Chenari, Hossein Mahmoudi; Kangarlou, Haleh

    2016-10-01

    The major objective of this work is focused on the preparation and characterization of poly (vinyl alcohol) (PVA) embedding tungsten oxide nanoparticles based on electrospinning technique. A surfactant (CTAB) was introduced to incorporate tungsten oxide nanoparticles into the PVA nanofibers homogeneously. To prepare a viscous solution of PVA nanofiber containing tungsten oxide nanoparticles, the distance between the tip of the needle and the surface of the foil was chosen as 10 and 15 cm. The tungsten oxide NPs/PVA composite nanofibers have been characterized using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and reflectance spectrum in the wave length range of 200-1200 nm. Fiber diameters decrease with increasing of tip-to-collector distance from 10 to 15 cm. The average diameters were estimated about 165±30 nm and 145±30 nm from scanning electron microscopy at 10 and 15 cm, respectively. The optical properties of the electrospun nanofibers were examined by the Kramers-Kronig model. The optical results show that tungsten oxide nanopowder show almost five times higher conductivity, lower absorbance and zero band gap energy.

  5. Ceria-Zirconia Particles Wrapped in a 2D Carbon Envelope: Improved Low-Temperature Oxygen Transfer and Oxidation Activity.

    PubMed

    Aneggi, Eleonora; Rico-Perez, Veronica; de Leitenburg, Carla; Maschio, Stefano; Soler, Lluís; Llorca, Jordi; Trovarelli, Alessandro

    2015-11-16

    Engineering the interface between different components of heterogeneous catalysts at nanometer level can radically alter their performances. This is particularly true for ceria-based catalysts where the interactions are critical for obtaining materials with enhanced properties. Here we show that mechanical contact achieved by high-energy milling of CeO2-ZrO2 powders and carbon soot results in the formation of a core of oxide particles wrapped in a thin carbon envelope. This 2D nanoscale carbon arrangement greatly increases the number and quality of contact points between the oxide and carbon. Consequently, the temperatures of activation and transfer of the oxygen in ceria are shifted to exceptionally low temperatures and the soot combustion rate is boosted. The study confirms the importance of the redox behavior of ceria-zirconia particles in the mechanism of soot oxidation and shows that the organization of contact points at the nanoscale can significantly modify the reactivity resulting in unexpected properties and functionalities. PMID:26448053

  6. Ceria–Zirconia Particles Wrapped in a 2D Carbon Envelope: Improved Low-Temperature Oxygen Transfer and Oxidation Activity

    PubMed Central

    Aneggi, Eleonora; Rico-Perez, Veronica; de Leitenburg, Carla; Maschio, Stefano; Soler, Lluís; Llorca, Jordi; Trovarelli, Alessandro

    2015-01-01

    Engineering the interface between different components of heterogeneous catalysts at nanometer level can radically alter their performances. This is particularly true for ceria-based catalysts where the interactions are critical for obtaining materials with enhanced properties. Here we show that mechanical contact achieved by high-energy milling of CeO2–ZrO2 powders and carbon soot results in the formation of a core of oxide particles wrapped in a thin carbon envelope. This 2D nanoscale carbon arrangement greatly increases the number and quality of contact points between the oxide and carbon. Consequently, the temperatures of activation and transfer of the oxygen in ceria are shifted to exceptionally low temperatures and the soot combustion rate is boosted. The study confirms the importance of the redox behavior of ceria-zirconia particles in the mechanism of soot oxidation and shows that the organization of contact points at the nanoscale can significantly modify the reactivity resulting in unexpected properties and functionalities. PMID:26448053

  7. Ceria-Zirconia Particles Wrapped in a 2D Carbon Envelope: Improved Low-Temperature Oxygen Transfer and Oxidation Activity.

    PubMed

    Aneggi, Eleonora; Rico-Perez, Veronica; de Leitenburg, Carla; Maschio, Stefano; Soler, Lluís; Llorca, Jordi; Trovarelli, Alessandro

    2015-11-16

    Engineering the interface between different components of heterogeneous catalysts at nanometer level can radically alter their performances. This is particularly true for ceria-based catalysts where the interactions are critical for obtaining materials with enhanced properties. Here we show that mechanical contact achieved by high-energy milling of CeO2-ZrO2 powders and carbon soot results in the formation of a core of oxide particles wrapped in a thin carbon envelope. This 2D nanoscale carbon arrangement greatly increases the number and quality of contact points between the oxide and carbon. Consequently, the temperatures of activation and transfer of the oxygen in ceria are shifted to exceptionally low temperatures and the soot combustion rate is boosted. The study confirms the importance of the redox behavior of ceria-zirconia particles in the mechanism of soot oxidation and shows that the organization of contact points at the nanoscale can significantly modify the reactivity resulting in unexpected properties and functionalities.

  8. Localized photoelectrochemistry on a tungsten oxide-iron oxide thin film material library.

    PubMed

    Kollender, Jan Philipp; Mardare, Andrei Ionut; Hassel, Achim Walter

    2013-12-01

    A WO3-Fe2O3 thin film combinatorial library was fabricated using a vapor phase co-deposition method followed by a combined thermal annealing and oxidation process. The scanning electron microscopy (SEM) analysis of the library microstructure combined with X-ray diffraction (XRD) investigations suggested that α-Fe2O3 grains preferentially grow from boundaries of domains, containing finer grains of WO3 and Fe2WO6, forming filiform networks on the surface. The surface density of the hematite networks depends on the amount of Fe present in the library. Photocurrents measured at different applied biases using Photo Electrochemical Scanning Droplet Cell Microscopy (PE-SDCM) were analyzed and mapped along the entire compositional spread. A distinctive photocurrent peak was detected at 21.9 atom % Fe, and its appearance was correlated to the higher amount of hematite present in the library at this specific composition together with a specific WO3 crystallographic orientation ((222) orthorhombic or (400) monoclinic). This finding is confirmed by qualitative and quantitative XPS surface analysis at the photocurrent peak position in the material library. Thus the enhancement of the photocurrent cannot be exclusively attributed to certain surface modifications since only hematite was found on the library surface at the peak composition.

  9. Large-area alignment of tungsten oxide nanowires over flat and patterned substrates for room-temperature gas sensing.

    PubMed

    Cheng, Wei; Ju, Yanrui; Payamyar, Payam; Primc, Darinka; Rao, Jingyi; Willa, Christoph; Koziej, Dorota; Niederberger, Markus

    2015-01-01

    Alignment of nanowires over a large area of flat and patterned substrates is a prerequisite to use their collective properties in devices such as gas sensors. In this work, uniform single-crystalline ultrathin W18 O49 nanowires with diameters less than 2 nm and aspect ratios larger than 100 have been synthesized, and, despite their flexibility, assembled into thin films with high orientational order over a macroscopic area by the Langmuir-Blodgett technique. Alignment of the tungsten oxide nanowires was also possible on top of sensor substrates equipped with electrodes. Such sensor devices were found to exhibit outstanding sensitivity to H2 at room temperature. PMID:25412600

  10. Preheated ignition and work function studies on alkaline earth metal oxides coated tungsten electrodes of fluorescent lamps

    NASA Astrophysics Data System (ADS)

    Langer, Reinhard; Dar, Farrukh; Hilscher, Achim; Horn, Siegfried; Tidecks, Reinhard

    2015-03-01

    This paper describes measurements on the alkaline earth (Ba, Sr, Ca) oxide layers utilized as emitting material in fluorescent lamp electrodes. In a first approach we compared the emission capabilities of the different materials (BaO, SrO and CaO coatings on tungsten filaments) by their ability to facilitate the start of a lamp. In a second investigation the work function was measured quantitatively by means of a Kelvin probe. Basically, the results of both measurements coincide. The impact of sample geometry on measurement results of a Kelvin probe applied for work function measurements of lamp electrodes are discussed in detail.

  11. Revealing oxidative damage to enzymes of carbohydrate metabolism in yeast: An integration of 2D DIGE, quantitative proteomics, and bioinformatics.

    PubMed

    Boone, Cory H T; Grove, Ryan A; Adamcova, Dana; Braga, Camila P; Adamec, Jiri

    2016-07-01

    Clinical usage of lidocaine, a pro-oxidant has been linked with severe, mostly neurological complications. The mechanism(s) causing these complications is independent of the blockade of voltage-gated sodium channels. The budding yeast Saccharomyces cerevisiae lacks voltage-gated sodium channels, thus provides an ideal system to investigate lidocaine-induced protein and pathway alterations. Whole-proteome alterations leading to these complications have not been identified. To address this, S. cerevisiae was grown to stationary phase and exposed to an LC50 dose of lidocaine. The differential proteomes of lidocaine treatment and control were resolved 6 h post exposure using 2D DIGE. Amine reactive dyes and carbonyl reactive dyes were used to assess protein abundance and protein oxidation, respectively. Quantitative analysis of these dyes (⩾ 1.5-fold alteration, p ⩽ 0.05) revealed a total of 33 proteoforms identified by MS differing in abundance and/or oxidation upon lidocaine exposure. Network analysis showed enrichment of apoptotic proteins and cell wall maintenance proteins, while the abundance of proteins central to carbohydrate metabolism, such as triosephosphate isomerase and glyceraldehyde-3-phosphate dehydrogenase, and redox proteins superoxide dismutase and peroxiredoxin were significantly decreased. Enzymes of carbohydrate metabolism, such as phosphoglycerate kinase and enolase, the TCA cycle enzyme aconitase, and multiple ATP synthase subunits were found to be oxidatively modified. Also, the activity of aconitase was found to be decreased. Overall, these data suggest that toxic doses of lidocaine induce significant disruption of glycolytic pathways, energy production, and redox balance, potentially leading to cell malfunction and death. PMID:27193513

  12. Simple fabrication of flexible electrodes with high metal-oxide content: electrospun reduced tungsten oxide/carbon nanofibers for lithium ion battery applications

    NASA Astrophysics Data System (ADS)

    Lee, Jaehyuk; Jo, Changshin; Park, Bangrock; Hwang, Woonbong; Lee, Hyung Ik; Yoon, Songhun; Lee, Jinwoo

    2014-08-01

    A one-step and mass-production synthetic route for a flexible reduced tungsten oxide-carbon composite nanofiber (WOx-C-NF) film is demonstrated via an electrospinning technique. The WOx-C-NF film exhibits unprecedented high content of metal-oxides (~80 wt%) and good flexibility (the tensile strength of the specimen was 6.13 MPa) without the use of flexible support materials like CNTs or graphene. The WOx-C-NF film is directly used as an anode in a lithium ion battery (LIB). Compared with previously reported tungsten oxide electrodes, the WOx-C-NF film exhibits high reversible capacity (481 mA h g-1total electrode), stable cycle, and improved rate performance, without the use of additive carbon, a polymeric binder and a current collector. Moreover, control electrodes fabricated by conventional processes support the positive effects of both the freestanding electrode and metal-oxide embedded carbon 1-D nanofiber structure.A one-step and mass-production synthetic route for a flexible reduced tungsten oxide-carbon composite nanofiber (WOx-C-NF) film is demonstrated via an electrospinning technique. The WOx-C-NF film exhibits unprecedented high content of metal-oxides (~80 wt%) and good flexibility (the tensile strength of the specimen was 6.13 MPa) without the use of flexible support materials like CNTs or graphene. The WOx-C-NF film is directly used as an anode in a lithium ion battery (LIB). Compared with previously reported tungsten oxide electrodes, the WOx-C-NF film exhibits high reversible capacity (481 mA h g-1total electrode), stable cycle, and improved rate performance, without the use of additive carbon, a polymeric binder and a current collector. Moreover, control electrodes fabricated by conventional processes support the positive effects of both the freestanding electrode and metal-oxide embedded carbon 1-D nanofiber structure. Electronic supplementary information (ESI) available. See DOI: 10.1039/c4nr01033g

  13. Structure and electronic properties of pure and nitrogen doped nanocrystalline tungsten oxide thin films

    NASA Astrophysics Data System (ADS)

    Vemuri, Venkata Rama Sesha Ravi Kumar

    Tungsten oxide (WO3) is a multifunctional material which has applications in electronics, sensors, optoelectronics, and energy-related technologies. Recently, electronic structure modification of WO3 to design novel photocatalysts has garnered significant attention. However, a fundamental understanding of nitrogen-induced changes in the structure, morphology, surface/ interface chemistry, and electronic properties of WO 3 is a prerequisite to producing materials with the desired functionality and performance. Also, understanding the effect of thermodynamic and processing variables is highly desirable in order to derive the structure-property relationships in the W-O/W-O-N material system. The present work was, therefore, focused on studying the effects of processing parameters on the microstructure, optical properties, electrical conductivity, and electronic structures of pure and nitrogen-doped (N-doped) WO3 films grown by sputter deposition. Efforts were made to understand the properties and phenomena of pure and N-doped WO3 at reduced dimensionality (i.e., nanoscale dimensions). The results and analyses indicate that the growth temperature (Ts) has a significant effect on the microstructure of WO3 films. The grain size increases from 9 to 50 nm coupled with a phase transformation in the following sequence: amorphous (a) to monoclinic (m) to tetragonal (t) with increasing Ts (25--500°C). The nanocrystalline t-WO 3 films exhibit a strong (001) texturing. The band gap narrowing from 3.25 to 2.92 eV with grain size occurs due to quantum confinement effects. Correlated with the structure and optical properties, electrical conductivity also increases. Physical properties such as thickness, grain size, and density are also sensitive to oxygen/ nitrogen partial pressure during W-O/W-O-N sample fabrications. A direct relationship between film density and band gap is evident in nanocrystalline t-WO3 films grown at various oxygen pressures. It is observed that nitrogen

  14. Magnetic heating properties and neutron activation of tungsten-oxide coated biocompatible FePt core-shell nanoparticles.

    PubMed

    Seemann, K M; Luysberg, M; Révay, Z; Kudejova, P; Sanz, B; Cassinelli, N; Loidl, A; Ilicic, K; Multhoff, G; Schmid, T E

    2015-01-10

    Magnetic nanoparticles are highly desirable for biomedical research and treatment of cancer especially when combined with hyperthermia. The efficacy of nanoparticle-based therapies could be improved by generating radioactive nanoparticles with a convenient decay time and which simultaneously have the capability to be used for locally confined heating. The core-shell morphology of such novel nanoparticles presented in this work involves a polysilico-tungstate molecule of the polyoxometalate family as a precursor coating material, which transforms into an amorphous tungsten oxide coating upon annealing of the FePt core-shell nanoparticles. The content of tungsten atoms in the nanoparticle shell is neutron activated using cold neutrons at the Heinz Maier-Leibnitz (FRMII) neutron facility and thereby transformed into the radioisotope W-187. The sizeable natural abundance of 28% for the W-186 precursor isotope, a radiopharmaceutically advantageous gamma-beta ratio of γβ≈30% and a range of approximately 1mm in biological tissue for the 1.3MeV β-radiation are promising features of the nanoparticles' potential for cancer therapy. Moreover, a high temperature annealing treatment enhances the magnetic moment of nanoparticles in such a way that a magnetic heating effect of several degrees Celsius in liquid suspension - a prerequisite for hyperthermia treatment of cancer - was observed. A rise in temperature of approximately 3°C in aqueous suspension is shown for a moderate nanoparticle concentration of 0.5mg/ml after 15min in an 831kHz high-frequency alternating magnetic field of 250Gauss field strength (25mT). The biocompatibility based on a low cytotoxicity in the non-neutron-activated state in combination with the hydrophilic nature of the tungsten oxide shell makes the coated magnetic FePt nanoparticles ideal candidates for advanced radiopharmaceutical applications.

  15. Carbon dioxide sensing mechanisms of an electrocatalytic sensor/cell based on a tungsten stabilized bismuth oxide solid electrolyte

    NASA Astrophysics Data System (ADS)

    Shoemaker, Erika Leigh

    This work describes the specific O2/CO2 sensing mechanisms of a solid-state, thick-film, electrocatalytic cermet (ceramic/metallic) gas sensor based on a tungsten stabilized bismuth oxide (WBO) solid electrolyte. The sensors embody the same configuration of classical planar oxygen sensors with two catalytic electrodes sandwiching an oxygen ion conducting solid electrolyte and a buried metal oxide reference. The technique of cyclic voltammetry is used where a cyclic voltage is ramped across the electrodes to promote electrochemical reactions on the surface of the sensor. These reactions alter the ionic current flow through the solid electrolyte, generating voltage-current related responses (voltammograms) which are gas specific. The WBO sensors have the identical configuration of previously investigated sensors of this type based on a yttria stabilized zirconia (YSZ) solid electrolyte which show good response to O 2 but do not respond to CO2 to any degree. This dissertation examines the specific function of each solid electrolyte layer and relates them to both the WBO sensors ability to respond uniquely to CO2 and the YSZ sensors incapability to respond to CO2. The research suggests that the tungsten component of the WBO electrolyte along with the porosity of the WBO layer together are responsible for the unique CO 2 response of this sensor.

  16. Cyano-bridged coordination polymer hydrogel-derived Sn-Fe binary oxide nanohybrids with structural diversity: from 3D, 2D, to 2D/1D and enhanced lithium-storage performance

    NASA Astrophysics Data System (ADS)

    Zhang, Weiyu; Zhu, Xiaoshu; Chen, Xuguang; Zhou, Yiming; Tang, Yawen; Ding, Liangxin; Wu, Ping

    2016-05-01

    Metal oxide nanohybrids with uniform dimensions and controlled architectures possess unique compositional and structural superiorities, and thus harbor promising potential for a series of applications in energy, catalysis, and sensing systems. Herein, we propose a facile, general, and scalable cyano-bridged coordination polymer hydrogel-derived thermal-oxidation route for the construction of main-group metal and transition-metal heterometallic oxide nanohybrids with controlled constituents and architectures. The formation of Sn-Fe binary oxide nanohybrids has been demonstrated as an example by using cyano-bridged Sn(iv)-Fe(ii) bimetallic coordination polymer hydrogels (i.e., SnCl4-K4Fe(CN)6 cyanogels, Sn-Fe cyanogels) as precursors. The physicochemical properties of Sn-Fe cyanogels with different Sn/Fe ratios have been systematically examined, and it is found that perfect Sn-Fe cyanogels without unbridged Sn(iv) or Fe(ii) can be formed with Sn/Fe ratios from 2 : 1 to 1 : 2. More importantly, the simple adjustment of Sn/Fe ratios in the Sn-Fe cyanogel precursors can realize flexible dimensional control of the Sn-Fe binary oxide nanohybrids, and 2D/1D SnO2-Fe2O3 hierarchitectures, 2D SnO2-Fe2O3 nanosheets, and 3D SnO2-Fe2O3 networks have been synthesized using the Sn-Fe 1 : 2, Sn-Fe 1 : 1, and Sn-Fe 2 : 1 cyanogels as precursors, respectively. To demonstrate their compositional/structural superiorities and potential applications, the lithium-storage utilization of the Sn-Fe binary oxide nanohybrids has been selected as an objective application, and the nanohybrids exhibit Sn/Fe ratio-dependent lithium-storage performance. As a representative example, the 2D/1D SnO2-Fe2O3 hierarchitectures manifest markedly enhanced Li-storage performance in terms of reversible capacities and cycling stability in comparison with their constituent units, i.e., bare SnO2 nanosheets and Fe2O3 nanorods. The proposed cyanogel-derived thermal-oxidation strategy could open up new

  17. Tungsten carbide/porous carbon composite as superior support for platinum catalyst toward methanol electro-oxidation

    SciTech Connect

    Jiang, Liming; Fu, Honggang; Wang, Lei; Mu, Guang; Jiang, Baojiang; Zhou, Wei; Wang, Ruihong

    2014-01-01

    Graphical abstract: The WC nanoparticles are well dispersed in the carbon matrix. The size of WC nanoparticles is about 30 nm. It can be concluded that tungsten carbide and carbon composite was successfully prepared by the present synthesis conditions. - Highlights: • The WC/PC composite with high specific surface area was prepared by a simple way. • The Pt/WC/PC catalyst has superior performance toward methanol electro-oxidation. • The current density for methanol electro-oxidation is as high as 595.93 A g{sup −1} Pt. • The Pt/WC/PC catalyst shows better durability and stronger CO electro-oxidation. • The performance of Pt/WC/PC is superior to the commercial Pt/C (JM) catalyst. - Abstract: Tungsten carbide/porous carbon (WC/PC) composites have been successfully synthesized through a surfactant assisted evaporation-induced-assembly method, followed by a thermal treatment process. In particular, WC/PC-35-1000 composite with tungsten content of 35% synthesized at the carbonized temperature of 1000 °C, exhibited a specific surface area (S{sub BET}) of 457.92 m{sup 2} g{sup −1}. After loading Pt nanoparticles (NPs), the obtained Pt/WC/PC-35-1000 catalyst exhibits the highest unit mass electroactivity (595.93 A g{sup −1} Pt) toward methanol electro-oxidation, which is about 2.6 times as that of the commercial Pt/C (JM) catalyst. Furthermore, the Pt/WC/PC-35-1000 catalyst displays much stronger resistance to CO poisoning and better durability toward methanol electrooxidation compared with the commercial Pt/C (JM) catalyst. The high electrocatalytic activity, strong poison-resistivity and good stability of Pt/WC/PC-35-1000 catalyst are attributed to the porous structures and high specific surface area of WC/PC support could facilitate the rapid mass transportation. Moreover, synergistic effect between WC and Pt NPs is favorable to the higher catalytic performance.

  18. Probing the effects of 2D confinement on hydrogen dynamics in water and ice adsorbed in graphene oxide sponges.

    PubMed

    Romanelli, Giovanni; Senesi, Roberto; Zhang, Xuan; Loh, Kian Ping; Andreani, Carla

    2015-12-21

    We studied the single particle dynamics of water and ice adsorbed in graphene oxide (GO) sponges at T = 293 K and T = 20 K. We used Deep Inelastic Neutron Scattering (DINS) at the ISIS neutron and muon spallation source to derive the hydrogen mean kinetic energy, 〈EK〉, and momentum distribution, n(p). The goal of this work was to study the hydrogen dynamics under 2D confinement and the potential energy surface, fingerprinting the hydrogen interaction with the layered structure of the GO sponge. The observed scattering is interpreted within the framework of the impulse approximation. Samples of both water and ice adsorbed in GO show n(p) functions with almost harmonic and anisotropic line shapes and 〈EK〉 values in excess of the values found at the corresponding temperatures in the bulk. The hydrogen dynamics are discussed in the context of the interaction between the interfacial water and ice and the confining hydrophilic surface of the GO sponge. PMID:26556604

  19. Effect of tungsten on the electrochromic behaviour of sol-gel dip coated molybdenum oxide thin films

    SciTech Connect

    Dhanasankar, M.; Purushothaman, K.K.; Muralidharan, G.

    2010-05-15

    The paper describes the results obtained on the performance of Mo oxide and mixed W/Mo oxide thin films for possible electrochromic applications. Mo and W/Mo oxide films were deposited on conductive (FTO) glass substrates using sol-gel dip coating method. The films were annealed at 250 {sup o}C for 30 min. The structure and morphology of Mo and W/Mo oxide films were examined using XRD, SEM and EDS. XRD results indicate the amorphous nature of the Mo and W/Mo oxide films annealed for 30 min. The CV measurements revealed that the films prepared with 10 wt.% of tungsten exhibit maximum anodic/cathodic diffusion coefficient of 24.99/12.71 x 10{sup -11} cm{sup 2}/s. The same film exhibits a maximum transmittance variation ({Delta}T%) of 83.4% at 630 nm and 81.06% at 550 nm with the optical density of 1.00 and 1.13 respectively.

  20. Synthesis of 2D/2D Structured Mesoporous Co3O4 Nanosheet/N-Doped Reduced Graphene Oxide Composites as a Highly Stable Negative Electrode for Lithium Battery Applications.

    PubMed

    Sennu, Palanichamy; Kim, Hyo Sang; An, Jae Youn; Aravindan, Vanchiappan; Lee, Yun-Sung

    2015-08-01

    Mesoporous Co3O4 nanosheets (Co3 O4 -NS) and nitrogen-doped reduced graphene oxide (N-rGO) are synthesized by a facile hydrothermal approach, and the N-rGO/Co3O4 -NS composite is formulated through an infiltration procedure. Eventually, the obtained composites are subjected to various characterization techniques, such as XRD, Raman spectroscopy, surface area analysis, X-ray photoelectron spectroscopy (XPS), and TEM. The lithium-storage properties of N-rGO/Co3O4 -NS composites are evaluated in a half-cell assembly to ascertain their suitability as a negative electrode for lithium-ion battery applications. The 2D/2D nanostructured mesoporous N-rGO/Co3O4 -NS composite delivered a reversible capacity of about 1305 and 1501 mAh g(-1) at a current density of 80 mA g(-1) for the 1st and 50th cycles, respectively. Furthermore, excellent cyclability, rate capability, and capacity retention characteristics are noted for the N-rGO/Co3O4 -NS composite. This improved performance is mainly related to the existence of mesoporosity and a sheet-like 2D hierarchical morphology, which translates into extra space for lithium storage and a reduced electron pathway. Also, the presence of N-rGO and carbon shells in Co3O4 -NS should not be excluded from such exceptional performance, which serves as a reliable conductive channel for electrons and act as synergistically to accommodate volume expansion upon redox reactions. Ex-situ TEM, impedance spectroscopy, and XPS, are also conducted to corroborate the significance of the 2D morphology towards sustained lithium storage.

  1. Methanol electro-oxidation on platinum modified tungsten carbides in direct methanol fuel cells: a DFT study.

    PubMed

    Sheng, Tian; Lin, Xiao; Chen, Zhao-Yang; Hu, P; Sun, Shi-Gang; Chu, You-Qun; Ma, Chun-An; Lin, Wen-Feng

    2015-10-14

    In exploration of low-cost electrocatalysts for direct methanol fuel cells (DMFCs), Pt modified tungsten carbide (WC) materials are found to be great potential candidates for decreasing Pt usage whilst exhibiting satisfactory reactivity. In this work, the mechanisms, onset potentials and activity for electrooxidation of methanol were studied on a series of Pt-modified WC catalysts where the bare W-terminated WC(0001) substrate was employed. In the surface energy calculations of a series of Pt-modified WC models, we found that the feasible structures are mono- and bi-layer Pt-modified WCs. The tri-layer Pt-modified WC model is not thermodynamically stable where the top layer Pt atoms tend to accumulate and form particles or clusters rather than being dispersed as a layer. We further calculated the mechanisms of methanol oxidation on the feasible models via methanol dehydrogenation to CO involving C-H and O-H bonds dissociating subsequently, and further CO oxidation with the C-O bond association. The onset potentials for the oxidation reactions over the Pt-modified WC catalysts were determined thermodynamically by water dissociation to surface OH* species. The activities of these Pt-modified WC catalysts were estimated from the calculated kinetic data. It has been found that the bi-layer Pt-modified WC catalysts may provide a good reactivity and an onset oxidation potential comparable to pure Pt and serve as promising electrocatalysts for DMFCs with a significant decrease in Pt usage. PMID:26351805

  2. A study of the switching mechanism and electrode material of fully CMOS compatible tungsten oxide ReRAM

    NASA Astrophysics Data System (ADS)

    Chien, W. C.; Chen, Y. C.; Lai, E. K.; Lee, F. M.; Lin, Y. Y.; Chuang, Alfred T. H.; Chang, K. P.; Yao, Y. D.; Chou, T. H.; Lin, H. M.; Lee, M. H.; Shih, Y. H.; Hsieh, K. Y.; Lu, Chih-Yuan

    2011-03-01

    Tungsten oxide (WO X ) resistive memory (ReRAM), a two-terminal CMOS compatible nonvolatile memory, has shown promise to surpass the existing flash memory in terms of scalability, switching speed, and potential for 3D stacking. The memory layer, WO X , can be easily fabricated by down-stream plasma oxidation (DSPO) or rapid thermal oxidation (RTO) of W plugs universally used in CMOS circuits. Results of conductive AFM (C-AFM) experiment suggest the switching mechanism is dominated by the REDOX (Reduction-oxidation) reaction—the creation of conducting filaments leads to a low resistance state and the rupturing of the filaments results in a high resistance state. Our experimental results show that the reactions happen at the TE/WO X interface. With this understanding in mind, we proposed two approaches to boost the memory performance: (i) using DSPO to treat the RTO WO X surface and (ii) using Pt TE, which forms a Schottky barrier with WO X . Both approaches, especially the latter, significantly reduce the forming current and enlarge the memory window.

  3. Suppression of photo-bias induced instability for amorphous indium tungsten oxide thin film transistors with bi-layer structure

    NASA Astrophysics Data System (ADS)

    Liu, Po-Tsun; Chang, Chih-Hsiang; Chang, Chih-Jui

    2016-06-01

    This study investigates the instability induced by bias temperature illumination stress (NBTIS) for an amorphous indium-tungsten-oxide thin film transistor (a-IWO TFT) with SiO2 backchannel passivation layer (BPL). It is found that this electrical degradation phenomenon can be attributed to the generation of defect states during the BPL process, which deteriorates the photo-bias stability of a-IWO TFTs. A method proposed by adding an oxygen-rich a-IWO thin film upon the a-IWO active channel layer could effectively suppress the plasma damage to channel layer during BPL deposition process. The bi-layer a-IWO TFT structure with an oxygen-rich back channel exhibits superior electrical reliability of device under NBTIS.

  4. Poly-ε-caprolactone tungsten oxide nanoparticles as a contrast agent for X-ray computed tomography.

    PubMed

    Jakhmola, Anshuman; Anton, Nicolas; Anton, Halina; Messaddeq, Nadia; Hallouard, François; Klymchenko, Andrey; Mely, Yves; Vandamme, Thierry F

    2014-03-01

    Inorganic nanomaterials based on heavy elements represent a new class of contrast agents for X-ray computed tomography (CT). Recent advances have shown that these materials are highly suited for CT imaging due to their high density and X-ray absorption capabilities. In this contribution, we demonstrated that tungsten oxide (WO3) nanoparticles coated by poly-ε-caprolactone (PCL) can be used as efficient contrast agent for CT imaging. The obtained particles were characterized by electron microscopy (TEM and SEM), and dynamic light scattering (DLS). We also validated their use for enhanced in vivo imaging, since these nanoparticles were observed to display high X-ray attenuation properties and circulation time (up to 3 h), permitting blood pool imaging.

  5. Correlation of electrochromic properties and oxidation states in nanocrystalline tungsten trioxide.

    PubMed

    Darmawi, S; Burkhardt, S; Leichtweiss, T; Weber, D A; Wenzel, S; Janek, J; Elm, M T; Klar, P J

    2015-06-28

    Although tungsten trioxide (WO3) has been extensively studied since its electrochromic properties were first discovered, the mechanism responsible for the coloration or bleaching effect is still disputed. New insights into the coloration mechanism of electrochromic, nanocrystalline WO3 are provided in this paper by studying thin WO3 films combining the electrochemical and spectroscopic techniques. By employing in situ UV-Vis transmission spectroscopy at a fixed spectral band pass during electrochemical experiments, such as cyclic voltammetry, a two-step insertion process for both protons and lithium ions is identified, of which one step exhibits a significantly higher coloration efficiency than the other. To obtain a better understanding of the insertion process AxWO3 (A = H, Li,…) thin films were studied at different stages of intercalation using UV-Vis and X-ray photoelectron spectroscopy. The results show that the first step of the intercalation process represents the reduction from initial W(6+) to W(5+) and the second step the reduction of W(5+) to W(4+). We found that the blue coloration of this nanocrystalline tungsten trioxide is mainly due to the presence of W(4+) rather than that of W(5+). PMID:26018838

  6. Peculiarities of formation of phase composition, porous structure, and catalytic properties of tungsten oxide-based macroporous materials fabricated by sol–gel synthesis

    SciTech Connect

    Papynov, Evgeniy Konstantinovich; Mayorov, Vitaliy Yurevich; Palamarchuk, Marina Sergeevna; Avramenko, Valentin Aleksandrovich

    2014-02-15

    The method of template sol–gel synthesis of tungsten oxide-based macroporous materials using ‘core–shell’ latex particles as colloid templates is described. The chemical composition and structural characteristics of the synthesized macroporous oxide systems have been investigated. The peculiarities of formation of material phase composition and macroporous structure under different template thermal destruction conditions have been revealed. An optimal method of a targeted synthesis of the crystalline tungsten(VI) oxide having a defect-free macroporous structure (average pore size 160 nm) and efficient catalytic properties under organic liquid phase oxidation conditions has been suggested. The prospects of the fabricated material application as catalysts of hydrothermal oxidation of radionuclide organic complexes at radioactive waste decontamination have been demonstrated. - Highlights: • Macroporous tungsten oxides were fabricated via sol–gel process. • The correlation between synthesis conditions and composition was determined. • Influence of synthesis conditions on porous structure has been explained. • The effects of template thermodestruction have been set up. • High potential of such materials for catalysis applications has been shown.

  7. Roles of phenylalanine at position 120 and glutamic acid at position 222 in the oxidation of chiral substrates by cytochrome P450 2D6.

    PubMed

    Masuda, Kazufumi; Tamagake, Keietsu; Katsu, Takashi; Torigoe, Fumihiro; Saito, Keita; Hanioka, Nobumitsu; Yamano, Shigeru; Yamamoto, Shigeo; Narimatsu, Shizuo

    2006-02-01

    The roles of Phe-120 and Glu-222 in the oxidation of chiral substrates bunitrolol (BTL) and bufuralol (BF) by CYP2D6 are discussed. Wild-type CYP2D6 (CYP2D6-WT) oxidized BTL to 4-hydroxybunitrolol (4-OH-BTL) with substrate enantioselectivity of (R)-(+)-BTL > (S)-(-)-BTL. The same enzyme converted BF into 1''-hydroxybufuralol with substrate enantioselectivity of (R)-BF > (S)-BF and metabolite diastereoselectivity of (1''R)-OH < (1''S)-OH. The substitution of Phe-120 by alanine markedly increased the apparent K(m) and V(max) values for enantiomeric BTL 4-hydroxylation by CYP2D6. In contrast, the same substitution caused an increase only in V(max) values of (S)-BF 1''-hydroxylation without changing apparent K(m) values, while kinetic parameters (K(m) and V(max) values) for (R)-BF 1''-hydroxylation remained unchanged. Furthermore, the substitution of Glu-222 as well as Glu-216 by alanine remarkably decreased both the apparent K(m) and V(max) values without changing substrate enantioselectivity or metabolite diastereoselectivity. A computer-assisted simulation study using energy minimization and molecular dynamics techniques indicated that the hydrophobic interaction of an aromatic moiety of the substrate with Phe-120 and the ionic interaction of a basic nitrogen atom of the substrate with Glu-222 in combination with Glu-216 play important roles in the binding of BF and BTL by CYP2D6 and the orientation of these substrates in the active-site cavity. This modeling yielded a convincing explanation for the reversal of substrate enantioselectivity in BTL 4-hydroxylation between CYP2D6-WT and CYP2D6-V374M having methionine in place of Val-374, which supports the validity of this modeling.

  8. Ellipsometrically determined optical properties of nickel-containing tungsten oxide thin films: Nanostructure inferred from effective medium theory

    SciTech Connect

    Valyukh, I.; Green, S. V.; Granqvist, C. G.; Gunnarsson, K.; Niklasson, G. A.; Arwin, H.

    2012-08-15

    Films of Ni{sub x}W{sub 1-x} oxide with 0.05 {<=} x {<=} 0.53 were produced by reactive dc magnetron co-sputtering onto Si. Such films have documented electrochromism. Spectroscopic ellipsometry was used to extract accurate data on the dielectric function in the photon range 0.062 to 5.62 eV. The results for 0.62 to 5.62 eV were compared with computations from the Bruggeman effective medium theory applied to two nanostructural models: one representing a random mixture of structural entities characterized by the dielectric functions of WO{sub 3} and NiWO{sub 4} and the other describing a random mixture of WO{sub 3} and NiO. Unambiguous evidence was found in favor of the former model, and hence the films are composed of nanosized tungsten oxide and nickel tungstate. This agrees excellently with an earlier investigation of ours on Ni{sub x}W{sub 1-x} oxide films, where nanostructure was inferred from Raman spectroscopy, x-ray photoelectron spectroscopy, and x-ray diffraction.

  9. L-Edge Xanes Measurements of the Oxidation State of Tungsten in Iron Bearing and Iron Free Silicate Glasses

    NASA Technical Reports Server (NTRS)

    Danielson, L. R.; Righter, K.; Sutton, S.; Newville, M.

    2008-01-01

    Tungsten is important in constraining core formation of the Earth because this element is a moderately siderophile element (depleted 10 relative to chondrites) and, as a member of the Hf-W isotopic system, it is useful in constraining the timing of core formation. A number of previous experimental studies have been carried out to determine the silicate solubility and metal-silicate partitioning behavior of W, including its concomitant oxidation state. However, results of previous studies are inconsistent on whether W occurs as W(4+) or W(6+). It is assumed that W(4+) is the cation valence relevant to core formation. Given the sensitivity to silicate composition of high valence cations, knowledge of the oxidation state of W over a wide range of fO2 is critical to understanding the oxidation state of the mantle and core formation processes. This study seeks to measure the W valence and change in valence state over the range of fO2 most relevant to core formation, around IW-2.

  10. L-edge XANES measurements of the oxidation state of tungsten in iron bearing and iron free silicate glasses

    SciTech Connect

    Danielson, L.R.; Righter, K.; Sutton, S.; Newville, M.; Le, L.

    2008-04-28

    W{sup 4+} is relevant to core formation but W{sup 6+} may also occur. Silicate glasses show W{sup 6+} above IW and mixed valence below IW. The transition to W{sup 4+} only, appears to happen at or below IW-2 for iron free systems, but below IW-3 for iron bearing systems. Tungsten is important in constraining core formation of the Earth because this element is a moderately siderophile element (depleted {approx} 10 relative to chondrites) and, as a member of the Hf-W isotopic system, it is useful in constraining the timing of core formation. A number of previous experimental studies have been carried out to determine the silicate solubility and metal-silicate partitioning behavior of W, including its concomitant oxidation state. However, results of previous studies (Fig. 1) are inconsistent on whether W occurs as W{sup 4+} or W{sup 6+}. It is assumed that W{sup 4+} is the cation valence relevant to core formation. Given the sensitivity to silicate composition of high valence cations, knowledge of the oxidation state of W over a wide range of fO{sub 2} is critical to understanding the oxidation state of the mantle and core formation processes. This study seeks to measure the W valence and change in valence state over the range of fO{sub 2} most relevant to core formation, around IW-2.

  11. Flexible electrochromics: magnetron sputtered tungsten oxide (WO3-x) thin films on Lexan (optically transparent polycarbonate) substrates

    NASA Astrophysics Data System (ADS)

    Uday Kumar, K.; Murali, Dhanya S.; Subrahmanyam, A.

    2015-06-01

    Tungsten oxide (WO3-x) based electrochromics on flexible substrates is a topic of recent interest. The present communication reports the electrochromic properties of WO3-x thin films grown on lexan, an optically transparent polycarbonate thermoplastic substrate. The WO3-x films are prepared at room temperature (300 K) by the reactive DC magnetron sputtering technique. The physical properties of metal oxide thin films are known to be controlled by the oxygen stoichiometry of the film. In the present work, the WO3-x thin films are prepared by varying the oxygen flow rates. All the WO3-x thin films are amorphous in nature. The electrochromic performance of the WO3-x thin films is evaluated by cyclic voltammetry measurements on tin doped indium oxide (ITO) coated lexan and glass substrates. The optical band gap of WO3-x thin films grown on lexan substrates (at any given oxygen flow rate) is significantly higher than those grown on glass substrates. The coloration efficiency of WO3-x thin films (at an oxygen flow rate of 10 sccm) on lexan substrates is: 143.9 cm2 C-1 which is higher compared to that grown on glass: 90.4 cm2 C-1.

  12. Reactive oxygen species and oxidative DNA damage mediate the cytotoxicity of tungsten-nickel-cobalt alloys in vitro

    SciTech Connect

    Harris, R.M.; Williams, T.D.; Hodges, N.J.; Waring, R.H.

    2011-01-01

    Tungsten alloys (WA) have been introduced in an attempt to find safer alternatives to depleted uranium and lead munitions. However, it is known that at least one alloy, 91% tungsten-6% nickel-3% cobalt (WNC-91-6-3), causes rhabdomyosarcomas when fragments are implanted in rat muscle. This raises concerns that shrapnel, if not surgically removable, may result in similar tumours in humans. There is therefore a clear need to develop rapid and robust in vitro methods to characterise the toxicity of different WAs in order to identify those that are most likely to be harmful to human health and to guide development of new materials in the future. In the current study we have developed a rapid visual in vitro assay to detect toxicity mediated by individual WA particles in cultured L6-C11 rat muscle cells. Using a variety of techniques (histology, comet assay, caspase-3 activity, oxidation of 2'7'-dichlorofluorescin to measure the production of reactive oxygen species and whole-genome microarrays) we show that, in agreement with the in vivo rat carcinogenicity studies, WNC-91-6-3 was the most toxic of the alloys tested. On dissolution, it produces large amounts of reactive oxygen species, causes significant amounts of DNA damage, inhibits caspase-3, triggers a severe hypoxic response and kills the cells in the immediate vicinity of the alloy particles within 24 h. By combining these in vitro data we offer a mechanistic explanation of the effect of this alloy in vivo and show that in vitro tests are a viable alternative for assessing new alloys in the future.

  13. The formation of tungsten doped Al2O3/ZnO coatings on aluminum by plasma electrolytic oxidation and their application in photocatalysis

    NASA Astrophysics Data System (ADS)

    Stojadinović, Stevan; Vasilić, Rastko; Radić, Nenad; Tadić, Nenad; Stefanov, Plamen; Grbić, Boško

    2016-07-01

    Tungsten doped Al2O3/ZnO coatings are formed by plasma electrolytic oxidation of aluminum substrate in supporting electrolyte (0.1 M boric acid + 0.05 M borax + 2 g/L ZnO) with addition of different concentrations of Na2WO4·2H2O. The morphology, crystal structure, chemical composition, and light absorption characteristics of formed surface coatings are investigated. The X-ray diffraction and X-ray photoelectron spectroscopy results indicate that formed surface coatings consist of alpha and gamma phase of Al2O3, ZnO, metallic tungsten and WO3. Obtained results showed that incorporated tungsten does not have any influence on the absorption spectra of Al2O3/ZnO coatings, which showed invariable band edge at about 385 nm. The photocatalytic activity of undoped and tungsten doped Al2O3/ZnO coatings is estimated by the photodegradation of methyl orange. The photocatalytic activity of tungsten doped Al2O3/ZnO coatings is higher thanof undoped Al2O3/ZnO coatings; the best photocatalytic activity is ascribed to coatings formed in supporting electrolyte with addition of 0.3 g/L Na2WO4·2H2O. Tungsten in Al2O3/ZnO coatings acts as a charge trap, thus reducing the recombination rate of photogenerated electron-hole pairs. The results of PL measurements are in agreement with photocatalytic activity. Declining PL intensity corresponds to increasing photocatalytic activity of the coatings, indicating slower recombination of electron-hole pairs.

  14. Tungsten-incorporation induced red-shift in the bandgap of gallium oxide thin films

    SciTech Connect

    Rubio, E. J.; Ramana, C. V.

    2013-05-13

    Tungsten (W) incorporated Ga{sub 2}O{sub 3} films were produced by co-sputter deposition. W-concentration was varied by the applied sputtering-power. The structure and optical properties of W-incorporated Ga{sub 2}O{sub 3} films were evaluated using X-ray diffraction, scanning electron microscopy, and spectrophotometric measurements. No secondary phase formation was observed in W-incorporated Ga{sub 2}O{sub 3} films. W-induced effects were significant on the structure and optical properties of Ga{sub 2}O{sub 3} films. The bandgap of Ga{sub 2}O{sub 3} films without W-incorporation was {approx}5 eV. Red-shift in the bandgap was noted with increasing W-concentration indicating the electronic structure changes in W-Ga{sub 2}O{sub 3} films. A functional relationship between W-concentration and optical property is discussed.

  15. Crystal Structure and Catalytic Behavior in Olefin Epoxidation of a One-Dimensional Tungsten Oxide/Bipyridine Hybrid.

    PubMed

    Amarante, Tatiana R; Antunes, Margarida M; Valente, Anabela A; Paz, Filipe A Almeida; Pillinger, Martyn; Gonçalves, Isabel S

    2015-10-19

    The tungsten oxide/2,2'-bipyridine hybrid material [WO3(2,2'-bpy)]·nH2O (n = 1-2) (1) has been prepared in near quantitative yield by the reaction of H2WO4, 2,2'-bpy, and H2O in the mole ratio of ca. 1:2:700 at 160 °C for 98 h in a rotating Teflon-lined digestion bomb. The solid-state structure of 1 was solved and refined through Rietveld analysis of high-resolution synchrotron X-ray diffraction data collected for the microcrystalline powder. The material, crystallizing in the orthorhombic space group Iba2, is composed of a one-dimensional organic-inorganic hybrid polymer, ∞(1)[WO3(2,2'-bpy)], topologically identical to that found in the previously reported anhydrous phases [MO3(2,2'-bpy)] (M = Mo, W). While in the latter the N,N'-chelated 2,2'-bpy ligands of adjacent corner-shared {MO4N2} octahedra are positioned on the same side of the 1D chain, in 1 the 2,2'-bpy ligands alternate above and below the chain. The catalytic behavior of compound 1 for the epoxidation of cis-cyclooctene was compared with that for several other tungsten- or molybdenum-based (pre)catalysts, including the hybrid polymer [MoO3(2,2'-bpy)]. While the latter exhibits superior performance when tert-butyl hydroperoxide (TBHP) is used as the oxidant, compound 1 is superior when aqueous hydrogen peroxide is used, allowing near-quantitative conversion of the olefin to the epoxide. With H2O2, compounds 1 and [MoO3(2,2'-bpy)] act as sources of soluble active species, namely, the oxodiperoxo complex [MO(O2)2(2,2'-bpy)], which is formed in situ. Compounds 1 and [WO(O2)2(2,2'-bpy)] (2) were further tested in the epoxidation of cyclododecene, trans-2-octene, 1-octene, (R)-limonene, and styrene. The structure of 2 was determined by single-crystal X-ray diffraction and found to be isotypical with the molybdenum analogue. PMID:26134888

  16. Crystal Structure and Catalytic Behavior in Olefin Epoxidation of a One-Dimensional Tungsten Oxide/Bipyridine Hybrid.

    PubMed

    Amarante, Tatiana R; Antunes, Margarida M; Valente, Anabela A; Paz, Filipe A Almeida; Pillinger, Martyn; Gonçalves, Isabel S

    2015-10-19

    The tungsten oxide/2,2'-bipyridine hybrid material [WO3(2,2'-bpy)]·nH2O (n = 1-2) (1) has been prepared in near quantitative yield by the reaction of H2WO4, 2,2'-bpy, and H2O in the mole ratio of ca. 1:2:700 at 160 °C for 98 h in a rotating Teflon-lined digestion bomb. The solid-state structure of 1 was solved and refined through Rietveld analysis of high-resolution synchrotron X-ray diffraction data collected for the microcrystalline powder. The material, crystallizing in the orthorhombic space group Iba2, is composed of a one-dimensional organic-inorganic hybrid polymer, ∞(1)[WO3(2,2'-bpy)], topologically identical to that found in the previously reported anhydrous phases [MO3(2,2'-bpy)] (M = Mo, W). While in the latter the N,N'-chelated 2,2'-bpy ligands of adjacent corner-shared {MO4N2} octahedra are positioned on the same side of the 1D chain, in 1 the 2,2'-bpy ligands alternate above and below the chain. The catalytic behavior of compound 1 for the epoxidation of cis-cyclooctene was compared with that for several other tungsten- or molybdenum-based (pre)catalysts, including the hybrid polymer [MoO3(2,2'-bpy)]. While the latter exhibits superior performance when tert-butyl hydroperoxide (TBHP) is used as the oxidant, compound 1 is superior when aqueous hydrogen peroxide is used, allowing near-quantitative conversion of the olefin to the epoxide. With H2O2, compounds 1 and [MoO3(2,2'-bpy)] act as sources of soluble active species, namely, the oxodiperoxo complex [MO(O2)2(2,2'-bpy)], which is formed in situ. Compounds 1 and [WO(O2)2(2,2'-bpy)] (2) were further tested in the epoxidation of cyclododecene, trans-2-octene, 1-octene, (R)-limonene, and styrene. The structure of 2 was determined by single-crystal X-ray diffraction and found to be isotypical with the molybdenum analogue.

  17. 2D nanostructures for water purification: graphene and beyond.

    PubMed

    Dervin, Saoirse; Dionysiou, Dionysios D; Pillai, Suresh C

    2016-08-18

    Owing to their atomically thin structure, large surface area and mechanical strength, 2D nanoporous materials are considered to be suitable alternatives for existing desalination and water purification membrane materials. Recent progress in the development of nanoporous graphene based materials has generated enormous potential for water purification technologies. Progress in the development of nanoporous graphene and graphene oxide (GO) membranes, the mechanism of graphene molecular sieve action, structural design, hydrophilic nature, mechanical strength and antifouling properties and the principal challenges associated with nanopore generation are discussed in detail. Subsequently, the recent applications and performance of newly developed 2D materials such as 2D boron nitride (BN) nanosheets, graphyne, molybdenum disulfide (MoS2), tungsten chalcogenides (WS2) and titanium carbide (Ti3C2Tx) are highlighted. In addition, the challenges affecting 2D nanostructures for water purification are highlighted and their applications in the water purification industry are discussed. Though only a few 2D materials have been explored so far for water treatment applications, this emerging field of research is set to attract a great deal of attention in the near future.

  18. 2D nanostructures for water purification: graphene and beyond.

    PubMed

    Dervin, Saoirse; Dionysiou, Dionysios D; Pillai, Suresh C

    2016-08-18

    Owing to their atomically thin structure, large surface area and mechanical strength, 2D nanoporous materials are considered to be suitable alternatives for existing desalination and water purification membrane materials. Recent progress in the development of nanoporous graphene based materials has generated enormous potential for water purification technologies. Progress in the development of nanoporous graphene and graphene oxide (GO) membranes, the mechanism of graphene molecular sieve action, structural design, hydrophilic nature, mechanical strength and antifouling properties and the principal challenges associated with nanopore generation are discussed in detail. Subsequently, the recent applications and performance of newly developed 2D materials such as 2D boron nitride (BN) nanosheets, graphyne, molybdenum disulfide (MoS2), tungsten chalcogenides (WS2) and titanium carbide (Ti3C2Tx) are highlighted. In addition, the challenges affecting 2D nanostructures for water purification are highlighted and their applications in the water purification industry are discussed. Though only a few 2D materials have been explored so far for water treatment applications, this emerging field of research is set to attract a great deal of attention in the near future. PMID:27506268

  19. Electronic and optical properties of tungsten oxide related materials and first-principles theory of electrochromism

    NASA Astrophysics Data System (ADS)

    Xue, Yu

    Tungsten trioxide WO3 is an interesting semiconductor with a wide-range of potential applications. One important property of WO 3 is its electrochromic behavior, which has generated significant research interest. Electrochromic materials exhibit reversible and persistent changes of the optical properties, hence their color, upon applying an electrical pulse. The applications of the electrochromic WO3 range from information display, light shutters, to energy efficient smart windows. Although there are many materials that exhibit electrochromic behavior, tungsten trioxide is one of the most extensively studied ones due to its superior coloration efficiency, short response time and reversibility. Enhanced electrochromic properties in WO3 nanowires have been reported recently. Despite much research effort, a first-principles theory for the coloration mechanism in this material has not emerged. In this work, we establish a first-principles theory for the coloration mechanism in NaxWOx, which is also able to explain the electrochromism in WO3. Chapter 1 gives a brief introduction to electrochromism in WO3 and related materials. In Chapter 2, we summarize the theories and computational methods used in this work including the local density approximation (LDA) within density functional theory (DFT), pseudopotential planewave formalism and the GW approximation. We study the crystal and electronic structures of WO3 in Chapter 3. WO3 has a basic octahedron structure. From -140 ˜ 830°C, the crystal structure changes from monoclinic to triclinic, again monoclicnic, then successively orthorhombic, tetragonal, and again tetragonal. Several groups have investigated the electronic structure of WO3 within DFT, but the band gap is severely underestimated compared with experiment. We have carried out quasiparticle calculations within the GW approximation. The calculated band gap is much closer to experimental results. Chapter 4 and Chapter 5 discuss the optical properties and

  20. A novel composite electrode based on tungsten oxide nanoparticles and carbon nanotubes for the electrochemical determination of paracetamol.

    PubMed

    Baytak, Aysegul Kutluay; Duzmen, Sehriban; Teker, Tugce; Aslanoglu, Mehmet

    2015-12-01

    An electrochemical sensor was prepared by the modification of a glassy carbon electrode (GCE) with a composite of nanoparticles of tungsten oxide (WO3) and carbon nanotubes (CNTs) for the quantification of paracetamol (PR). Energy dispersive X-ray analysis (EDX) and scanning electron microscopy (SEM) were performed for the characterization of the nanocomposite layer. Compared with a bare GCE and a GCE modified with CNTs, the proposed electrode (WO3NPs/CNTs/GCE) exhibited a well-defined redox couple for PR and a marked enhancement of the current response. The experimental results also showed that ascorbic acid (AA) did not interfere with the selective determination of PR. The proposed electrode was used for the determination of PR in 0.1M phosphate buffer solution (PBS) at pH7.0 using square wave voltammetry (SWV). The peak current increased linearly with the concentration of PR in the range of 1.0×10(-9)-2.0×10(-7)M. The detection limit (LOD) was 5.54×10(-11)M (based on 3Sb/m). The proposed voltammetric sensor provided long-time stability, improved voltammetric behavior and good reproducibility for PR. The selective, accurate and precise determination of PR makes the proposed electrode of great interest for monitoring its therapeutic use.

  1. Investigation of the Thermal Behavior of Single-Walled Carbon Nanotubes and Tungsten Oxide Nanostructures Using Raman Spectroscopy

    NASA Astrophysics Data System (ADS)

    Misra, Prabhakar; Casimir, Daniel; Sanchez, Raul F.; Craig, Christina; Bartley, Sarah; Baliga, Shankar

    Thermal conductivity measurements of a variety of Single-Walled Carbon Nanotube (SWCNT) samples via Raman shifts of the G+ band frequency around 1592 cm-1 recorded with a 780 nm laser as a function of laser power (0 - 25 mW) have allowed quantitative estimates of the purity levels of the SWCNTs. In addition, Raman spectra of a variety of tungsten oxide (WO3) nanomaterial samples, namely WO3 on silicon substrate, as well as nanopowder and nanowires, exhibited clear variation in O-H band features around 1550 cm-1 due to effects of ambient humidity, as well as other spectral features due to gas (NOx) exposure have been documented, as a function of varying temperature (in the range 27 - 200°C). Thermal characteristics of SWCNTs and WO3 samples, along with the associated Molecular Dynamics simulations performed, will prove useful for thermal energy storage and gas sensing applications. Financial support from the National Science Foundation (NSF PHY-1358727) is gratefully acknowledged.

  2. Strongly coupled Pd nanotetrahedron/tungsten oxide nanosheet hybrids with enhanced catalytic activity and stability as oxygen reduction electrocatalysts.

    PubMed

    Lu, Yizhong; Jiang, Yuanyuan; Gao, Xiaohui; Wang, Xiaodan; Chen, Wei

    2014-08-20

    The design and synthesis of highly active oxygen reduction reaction (ORR) catalysts with strong durability at low cost is extremely desirable but still remains a significant challenge. Here we develop an efficient strategy that utilizes organopalladium(I) complexes containing palladium-palladium bonds as precursors for the synthesis of strongly coupled Pd tetrahedron-tungsten oxide nanosheet hybrids (Pd/W18O49) to improve the electrocatalytic activity and stability of Pd nanocrystals. The hybrid materials are synthesized by direct nucleation, growth, and anchoring of Pd tetrahedral nanocrystals on the in situ-synthesized W18O49 nanosheets. Compared to supportless Pd nanocrystals and W18O49, their hybrids exhibited not only surprisingly high activity but also superior stability to Pt for the ORR in alkaline solutions. X-ray photoelectron spectroscopy, high-resolution transmission electron microscopy, and electrochemical analyses indicated that the enhanced electrocatalytic activity and durability are associated with the increased number and improved catalytic activity of active sites, which is induced by the strong interaction between the Pd tetrahedrons and W18O49 nanosheet supports. The present study provides a novel strategy for synthesizing hybrid catalysts with strong chemical attachment and electrical coupling between nanocatalysts and supports. The strategy is expected to open up exciting opportunities for developing a novel class of metal-support hybrid nanoelectrocatalysts with improved ORR activity and durability for both fuel cells and metal-air batteries. PMID:25054583

  3. Curvature aided efficient axial field emission from carbon nanofiber-reduced graphene oxide superstructures on tungsten wire substrate

    NASA Astrophysics Data System (ADS)

    Jha, Arunava; Roy, Rajarshi; Sen, Dipayan; Chattopadhyay, Kalyan K.

    2016-03-01

    Field emission characteristics found in reduced graphene oxide (RGO) and RGO based composite systems have always been an area of research interest mainly due to presence of prolific quasi aligned edges working as emitter sites. However, the specific role and extent of edge curvature geometry in RGO systems in regards to the enhancement of field emission has not discussed thoroughly prior to this work. In this work we demonstrate enhanced axial field emission due to top assembly of thin RGO layer over a quasi-vertically aligned carbon nanofiber thin film supported on a tungsten wire substrate. Furthermore, simulation analysis for our RGO based hybrid system using finite element modeling showed that two-stage local field amplification in RGO is responsible for the overall improvement of field emission characteristics. In support of our findings, a tentative explanation has been proposed based on the additional emission from RGO edges in between the CNF network resulting to the enhancement of axial field emission in the nanocomposite superstructure.

  4. Functionalization of tungsten oxide into MWCNT and its application for sunlight-induced degradation of rhodamine B.

    PubMed

    Saleh, Tawfik A; Gupta, Vinod K

    2011-10-15

    A composite of multi-walled carbon nanotube/tungsten oxide (MWCNT/WO(3)) has been successfully synthesized. The prepared composite was characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM), high-resolution transmission electron microscopy (HRTEM) and Fourier transform infrared spectroscopy (FTIR). The catalytic activity was investigated by rhodamine B degradation under solar irradiation. The influence of various degradation parameters such as solar illumination time, initial dye concentration, dosage and pH was investigated. It was found that the composite exhibits an enhanced photocatalytic activity as compared with WO(3) and a mechanical mixture of MWCNTs and WO(3). The enhancement in photocatalytic performance of the MWCNT/WO(3) composite has been explained based on adsorption ability and electron transportation as a result of a strong interaction between WO(3) and MWCNTs. Besides, MWCNTs acts as dispersing agent preventing WO(3) from agglomerating during the catalytic process, providing a high active surface area of the catalyst. A reasonable mechanism for the enhanced reactivity was proposed.

  5. A novel composite electrode based on tungsten oxide nanoparticles and carbon nanotubes for the electrochemical determination of paracetamol.

    PubMed

    Baytak, Aysegul Kutluay; Duzmen, Sehriban; Teker, Tugce; Aslanoglu, Mehmet

    2015-12-01

    An electrochemical sensor was prepared by the modification of a glassy carbon electrode (GCE) with a composite of nanoparticles of tungsten oxide (WO3) and carbon nanotubes (CNTs) for the quantification of paracetamol (PR). Energy dispersive X-ray analysis (EDX) and scanning electron microscopy (SEM) were performed for the characterization of the nanocomposite layer. Compared with a bare GCE and a GCE modified with CNTs, the proposed electrode (WO3NPs/CNTs/GCE) exhibited a well-defined redox couple for PR and a marked enhancement of the current response. The experimental results also showed that ascorbic acid (AA) did not interfere with the selective determination of PR. The proposed electrode was used for the determination of PR in 0.1M phosphate buffer solution (PBS) at pH7.0 using square wave voltammetry (SWV). The peak current increased linearly with the concentration of PR in the range of 1.0×10(-9)-2.0×10(-7)M. The detection limit (LOD) was 5.54×10(-11)M (based on 3Sb/m). The proposed voltammetric sensor provided long-time stability, improved voltammetric behavior and good reproducibility for PR. The selective, accurate and precise determination of PR makes the proposed electrode of great interest for monitoring its therapeutic use. PMID:26354251

  6. A series of aluminum tungsten oxides crystallizing in a new ReO 3-related structure type

    NASA Astrophysics Data System (ADS)

    Krumeich, Frank; Patzke, Greta R.

    2008-10-01

    A series of new aluminum tungsten oxides with the general formula Al 4W 2nO 6n+2 ( n=4-7) was found and structurally characterized by electron diffraction, high-resolution transmission electron microscopy (HRTEM) and high angle annular dark field scanning transmission electron microscopy (HAADF-STEM). The structural model for Al 4W 10O 32 ( I4/ mmm (space group no. 139); a≈0.375, c≈3.95 nm) consists of slabs of [5×∞×∞] corner-sharing WO 6 octahedra that are connected via edge-sharing to AlO 6 octahedra. Simulated HRTEM images agree well with the experimental ones and thus support the proposed structural model. The connection between adjacent slabs of WO 3 via AlO 6 octahedra represents a novel variant of crystallographic shear operation for ReO 3-type structures. The crystallites display a wide range of stacking sequences that are frequently intergrown with each other.

  7. Influence of carbon and metal oxide nanomaterials on aqueous concentrations of the munition constituents cyclotrimethylenetrinitramine (RDX) and tungsten.

    PubMed

    Brame, Jonathon A; Kennedy, Alan J; Lounds, Christopher D; Bednar, Anthony J; Alvarez, Pedro J J; Scott, Andrea M; Stanley, Jacob K

    2014-05-01

    There is an increasing likelihood of interactions between nanomaterials and munitions constituents in the environment resulting from the use of nanomaterials as additives to energetic formulations and potential contact in waste streams from production facilities and runoff from training ranges. The purpose of the present research was to determine the ability of nano-aluminum oxide (Al(2)O(3)) and multiwalled carbon nanotubes (MWCNTs) to adsorb the munitions constituents cyclotrimethylenetrinitramine (RDX) and tungsten (W) from aqueous solution as a first step in determining the long-term exposure, transport, and bioavailability implications of such interactions. The results indicate significant adsorption of RDX by MWCNTs and of W by nano-Al(2)O(3) (but not between W and MWCNT or RDX and nano-Al(2)O(3)). Kinetic sorption and desorption investigations indicated that the most sorption occurs nearly instantaneously (<5 min), with a relatively slower, secondary binding leading to statistically significant but relatively smaller increases in adsorption over 30 d. The RDX sorption that occurred during the initial interaction was irreversible, with long-term, reversible sorption likely the result of a secondary interaction; as interaction time increased, however, the portion of W irreversibly sorbed onto nano-Al(2)O(3) also increased. The present study shows that strong interactions between some munitions constituents and nanomaterials following environmental release are likely. Time-dependent binding has implications for the bioavailability, migration, transport, and fate of munitions constituents in the environment.

  8. Comparison of 2-D model simulations of ozone and nitrous oxide at high latitudes with stratospheric measurements

    NASA Technical Reports Server (NTRS)

    Proffitt, M. H.; Solomon, S.; Loewenstein, M.

    1992-01-01

    A linear reference relationship between O3 and N2O has been used to estimate polar winter O3 loss from aircraft data taken in the lower stratosphere. Here, this relationship is evaluated at high latitudes by comparing it with a 2D model simulation and with NIMBUS 7 satellite measurements. Although comparisons with satellite measurements are limited to January through May, the model simulations are compared during other seasons. The model simulations and the satellite data are found to be consistent with the winter O3 loss analysis. It is shown that such analyses are likely to be inappropriate during other seasons.

  9. Synergistic effect of sunlight induced photothermal conversion and H2O2 release based on hybridized tungsten oxide gel for cancer inhibition

    PubMed Central

    Wang, Cong; Gao, Yibo; Gao, Xinghua; Wang, Hua; Tian, Jingxuan; Wang, Li; Zhou, Bingpu; Ye, Ziran; Wan, Jun; Wen, Weijia

    2016-01-01

    A highly efficient photochromic hydrogel was successfully fabricated via casting precursor, which is based on amorphous tungsten oxide and poly (ethylene oxide)-block-poly (propylene oxide)-block-poly (ethylene oxide). Under simulated solar illumination, the hydrogel has a rapid and controlled temperature increasing ratio as its coloration degree. Localized electrons in the amorphous tungsten oxide play a vital role in absorption over a broad range of wavelengths from 400 nm to 1100 nm, encompassing the entire visible light and infrared regions in the solar spectrum. More importantly, the material exhibits sustainable released H2O2 induced by localized electrons, which has a synergistic effect with the rapid surface temperature increase. The amount of H2O2 released by each film can be tuned by the light irradiation, and the film coloration can indicate the degree of oxidative stress. The ability of the H2O2-releasing gels in vitro study was investigated to induce apoptosis in melanoma tumor cells and NIH 3T3 fibroblasts. The in vivo experimental results indicate that these gels have a greater healing effect than the control in the early stages of tumor formation. PMID:27775086

  10. Evaporation-assisted high-power impulse magnetron sputtering: The deposition of tungsten oxide as a case study

    SciTech Connect

    Hemberg, Axel; Dauchot, Jean-Pierre; Snyders, Rony; Konstantinidis, Stephanos

    2012-07-15

    The deposition rate during the synthesis of tungsten trioxide thin films by reactive high-power impulse magnetron sputtering (HiPIMS) of a tungsten target increases, above the dc threshold, as a result of the appropriate combination of the target voltage, the pulse duration, and the amount of oxygen in the reactive atmosphere. This behavior is likely to be caused by the evaporation of the low melting point tungsten trioxide layer covering the metallic target in such working conditions. The HiPIMS process is therefore assisted by thermal evaporation of the target material.

  11. 2D to 3D crossover of the magnetic properties in ordered arrays of iron oxide nanocrystals.

    PubMed

    Faure, Bertrand; Wetterskog, Erik; Gunnarsson, Klas; Josten, Elisabeth; Hermann, Raphaël P; Brückel, Thomas; Andreasen, Jens Wenzel; Meneau, Florian; Meyer, Mathias; Lyubartsev, Alexander; Bergström, Lennart; Salazar-Alvarez, German; Svedlindh, Peter

    2013-02-01

    The magnetic 2D to 3D crossover behavior of well-ordered arrays of monodomain γ-Fe(2)O(3) spherical nanoparticles with different thicknesses has been investigated by magnetometry and Monte Carlo (MC) simulations. Using the structural information of the arrays obtained from grazing incidence small-angle X-ray scattering and scanning electron microscopy together with the experimentally determined values for the saturation magnetization and magnetic anisotropy of the nanoparticles, we show that MC simulations can reproduce the thickness-dependent magnetic behavior. The magnetic dipolar particle interactions induce a ferromagnetic coupling that increases in strength with decreasing thickness of the array. The 2D to 3D transition in the magnetic properties is mainly driven by a change in the orientation of the magnetic vortex states with increasing thickness, becoming more isotropic as the thickness of the array increases. Magnetic anisotropy prevents long-range ferromagnetic order from being established at low temperature and the nanoparticle magnetic moments instead freeze along directions defined by the distribution of easy magnetization directions.

  12. Results on the electrochromic and photocatalytic properties of vanadium doped tungsten oxide thin films prepared by reactive dc magnetron sputtering technique

    NASA Astrophysics Data System (ADS)

    Muthu Karuppasamy, K.; Subrahmanyam, A.

    2008-02-01

    In this investigation, vanadium doped tungsten oxide (V : WO3) thin films are prepared at room temperature by reactive dc magnetron sputtering employing a tungsten-vanadium 'inlay' target. In comparison with pure sputtered tungsten oxide thin films, 11% vanadium doping is observed to decrease the optical band gap, enhance the colour neutral property, decrease the coloration efficiency (from 121 to 13 cm2 C-1), increase the surface work function (4.68-4.83 eV) and significantly enhance the photocatalytic efficiency in WO3 thin films. These observations suggest that (i) vanadium creates defect levels that are responsible for optical band gap reduction, (ii) multivalent vanadium bonding with terminal oxygen in the WO3 lattice gives rise to localized covalent bonds and thus results in an increase in the work function, and (iii) a suitable work function of V : WO3 with ITO results in an enhancement of the photocatalytic activity. These results on electrochromic and photocatalytic properties of V : WO3 thin films show good promise in the low maintenance window application.

  13. A combined experimental and DFT study of active structures and self-cycle mechanisms of mononuclear tungsten peroxo complexes in oxidation reactions

    NASA Astrophysics Data System (ADS)

    Jin, Peng; Wei, Donghui; Wen, Yiqiang; Luo, Mengfei; Wang, Xiangyu; Tang, Mingsheng

    2011-04-01

    Tungsten peroxo complexes have been widely used in olefin epoxidation, alcohol oxidation, Baeyer-Villiger oxidation and other oxidation reactions, however, there is still not a unanimous viewpoint for the active structure of mononuclear tungsten peroxo complex by now. In this paper, the catalysis of mononuclear tungsten peroxo complexes 0- 5 with or without acidic ligands for the green oxidation of cyclohexene to adipic acid in the absence of organic solvent and phase-transfer catalyst has been researched in experiment. Then we have suggested two possible kinds of active structures of mononuclear tungsten peroxo complexes including peroxo ring ( nA, n = 0-1) and hydroperoxo ( nB, n = 0-1) structures, which have been investigated using density functional theory (DFT). Moreover, the calculations on self-cycle mechanisms involving the two types of active structures of tungsten peroxo complexes with and without oxalic acid ligand have also been carried out at the B3LYP/[LANL2DZ/6-31G(d, p)] level. The highest energy barrier are 26.17 kcal/mol ( 0A, peroxo ring structure without oxalic acid ligand), 23.91 kcal/mol ( 1A, peroxo ring structure with oxalic acid ligand), 18.19 kcal/mol ( 0B, hydroperoxo structure without oxalic acid ligand) and 13.10 kcal/mol ( 1B, hydroperoxo structure with oxalic acid ligand) in the four potential energy profiles, respectively. The results indicate that both the energy barriers of active structure self-cycle processes with oxalic acid ligands are lower than those without oxalic acid ligands, so the active structures with oxalic acid ligands should be easier to recycle, which is in good agreement with our experimental results. However, due to the higher energy of product than that of the reactant, the energy profile of the self-cycle process of 1B shows that the recycle of 1B could not occur at all in theory. Moreover, the crystal data of peroxo ring structure with oxalic acid ligand could be found in some experimental references. Thus

  14. A 2D transient numerical model combining heat/mass transport effects in a tubular solid oxide fuel cell

    NASA Astrophysics Data System (ADS)

    Mollayi Barzi, Y.; Ghassemi, M.; Hamedi, M. H.

    The purpose of this study is to present a 2D transient numerical model to predict the dynamic behavior of a tubular SOFC. In this model, the transient conservation equations (momentum, species and energy equations) are solved numerically and electrical and electrochemical outputs are calculated with an equivalent electrical circuit for the cell. The developed model determines the cell electrical and thermal responses to the variation of load current. Also it predicts the local EMF, state variables (pressure, temperature and species concentration) and cell performance for different cell load currents. Using this comprehensive model the dynamic behavior of Tubular SOFC is studied. First an initial steady state operating condition is set for the SOFC model and then the time response of the fuel cell to changes of some interested input parameters (like electrical load) is analyzed. The simulation starts when the cell is at the steady state in a specific output load. When the load step change takes place, the solution continues to reach to the new steady state condition. Then the cell transient behavior is analyzed. The results show that when the load current is stepped up, the output voltage decreases to a new steady state voltage in about 67 min.

  15. 1-Aza-15-Crown-5 Functionalized Graphene Oxide for 2D Graphene-Based Li⁺-ion Conductor.

    PubMed

    Banerjee, Moutusi; Gupta, Abhisek; Saha, Shyamal K; Chakravorty, Dipankar

    2015-07-01

    Attachment of Li(+) ion on graphene surface to realize Li(+)-ion conductor is a real challenge because of the weak interaction between the ions and the functional groups of graphene oxide; although, a large number of theoretical results are already available in the literature. To overcome this problem, graphene oxide is functionalized by 1-aza-15-crown-5, the cage-like structure containing four oxygens that can bind Li(+) ion through electrostatic interaction. Li(+) migration on graphene surface has been investigated using ac relaxation mechanism. Perfect Debye-type relaxation behavior with β (relaxation exponent) value ≈1 resulting from single ion is observed. The activation energy of Li(+) migration arising due to cation-π interaction is found to be 0.37 eV, which agrees well with recently reported theoretical value. It is believed that this study will help to design isolated ion conductors for Li(+)-ion battery.

  16. Nanostructured tungsten trioxide thin films synthesized for photoelectrocatalytic water oxidation: a review.

    PubMed

    Zhu, Tao; Chong, Meng Nan; Chan, Eng Seng

    2014-11-01

    The recent developments of nanostructured WO3 thin films synthesized through the electrochemical route of electrochemical anodization and cathodic electrodeposition for the application in photoelectrochemical (PEC) water splitting are reviewed. The key fundamental reaction mechanisms of electrochemical anodization and cathodic electrodeposition methods for synthesizing nanostructured WO3 thin films are explained. In addition, the effects of metal oxide precursors, electrode substrates, applied potentials and current densities, and annealing temperatures on size, composition, and thickness of the electrochemically synthesized nanostructured WO3 thin films are elucidated in detail. Finally, a summary is given for the general evaluation practices used to calculate the energy conversion efficiency of nanostructured WO3 thin films and a recommendation is provided to standardize the presentation of research results in the field to allow for easy comparison of reported PEC efficiencies in the near future. PMID:25274424

  17. First principles study of the photo-oxidation of water on tungsten trioxide (WO3).

    PubMed

    Valdés, A; Kroes, G-J

    2009-03-21

    The photo-oxidation of water on the monoclinic P2(1)/nWO(3) (200, 020, and 002) surfaces is investigated using density functional theory calculations, employing the PW91-generalized gradient approximation, and the method developed by Norskov et al. [J. Phys. Chem. B 108, 17886 (2004)] based on the free energy differences between the reaction intermediates. We first relax the bulk material unit cell and then investigate the relative stability of different surface terminations of WO(3) and analyze the overpotential needed for the photoelectrolysis of water. We found that the rate limiting step is the transfer of a proton from the surface adsorbed OH to the electrolyte, and that the computed overpotential for O(2) evolution (1.04 V) is available upon illumination of the surface with visible light.

  18. Nanostructured tungsten trioxide thin films synthesized for photoelectrocatalytic water oxidation: a review.

    PubMed

    Zhu, Tao; Chong, Meng Nan; Chan, Eng Seng

    2014-11-01

    The recent developments of nanostructured WO3 thin films synthesized through the electrochemical route of electrochemical anodization and cathodic electrodeposition for the application in photoelectrochemical (PEC) water splitting are reviewed. The key fundamental reaction mechanisms of electrochemical anodization and cathodic electrodeposition methods for synthesizing nanostructured WO3 thin films are explained. In addition, the effects of metal oxide precursors, electrode substrates, applied potentials and current densities, and annealing temperatures on size, composition, and thickness of the electrochemically synthesized nanostructured WO3 thin films are elucidated in detail. Finally, a summary is given for the general evaluation practices used to calculate the energy conversion efficiency of nanostructured WO3 thin films and a recommendation is provided to standardize the presentation of research results in the field to allow for easy comparison of reported PEC efficiencies in the near future.

  19. Predicting a quaternary tungsten oxide for sustainable photovoltaic application by density functional theory

    SciTech Connect

    Sarker, Pranab; Huda, Muhammad N.; Al-Jassim, Mowafak M.

    2015-12-07

    A quaternary oxide, CuSnW{sub 2}O{sub 8} (CTTO), has been predicted by density functional theory (DFT) to be a suitable material for sustainable photovoltaic applications. CTTO possesses band gaps of 1.25 eV (indirect) and 1.37 eV (direct), which were evaluated using the hybrid functional (HSE06) as a post-DFT method. The hole mobility of CTTO was higher than that of silicon. Further, optical absorption calculations demonstrate that CTTO is a better absorber of sunlight than Cu{sub 2}ZnSnS{sub 4} and CuIn{sub x}Ga{sub 1−x}Se{sub 2} (x = 0.5). In addition, CTTO exhibits rigorous thermodynamic stability comparable to WO{sub 3}, as investigated by different thermodynamic approaches such as bonding cohesion, fragmentation tendency, and chemical potential analysis. Chemical potential analysis further revealed that CTTO can be synthesized at flexible experimental growth conditions, although the co-existence of at least one secondary phase is likely. Finally, like other Cu-based compounds, the formation of Cu vacancies is highly probable, even at Cu-rich growth condition, which could introduce p-type activity in CTTO.

  20. From beads-to-wires-to-fibers of tungsten oxide: electrochromic response

    NASA Astrophysics Data System (ADS)

    Kadam, P. M.; Tarwal, N. L.; Shinde, P. S.; Patil, R. S.; Deshmukh, H. P.; Patil, P. S.

    2009-11-01

    Suitable host lattice and morphology for easy intercalation and deintercalation process are crucial requirements for electrochromic device. In this investigation, the evolution of structural and morphological changes and their effect on electrochromic (EC) properties of spray-deposited WO3 thin films are studied. Films of different morphologies were deposited from an ammonium tungstate precursor solution using a novel pulsed spray pyrolysis technique (PSPT) on tin-doped indium oxide (ITO) coated glass substrates by varying quantity of spraying solution. Interesting morphological transition from beads-to-wires-to-fibers as a function of quantity of sprayed solution has been demonstrated. The porosity, crystallinity and “open” structures in the films consisting of beads, wires, and fiber-like morphology enabled us to correlate these aspects to their EC performance. WO3 films comprising wire-like morphology (20 cc spraying quantity) exhibited better EC properties both in terms of coloration efficiency (42.7 cm2/C) and electrochemical stability (103 colored/bleached cycles) owing to their adequate open structure, porosity, and amorphicity, compared with the films having bead/fiber-like morphology.

  1. Evolution of Insulator-Metal Phase Transitions in Epitaxial Tungsten Oxide Films during Electrolyte-Gating.

    PubMed

    Nishihaya, Shinichi; Uchida, Masaki; Kozuka, Yusuke; Iwasa, Yoshihiro; Kawasaki, Masashi; Nishihaya, S; Uchida, M; Kozuka, Y; Iwasa, Y; Kawasaki, M; Iwasa, Y; Kawasaki, M

    2016-08-31

    An interface between an oxide and an electrolyte gives rise to various processes as exemplified by electrostatic charge accumulation/depletion and electrochemical reactions such as intercalation/decalation under electric field. Here we directly compare typical device operations of those in electric double layer transistor geometry by adopting A-site vacant perovskite WO3 epitaxial thin films as a channel material and two different electrolytes as gating agent. In situ measurements of X-ray diffraction and channel resistance performed during the gating revealed that in both the cases WO3 thin film reaches a new metallic state through multiple phase transitions, accompanied by the change in out-of-plane lattice constant. Electrons are electrostatically accumulated from the interface side with an ionic liquid, while alkaline metal ions are more uniformly intercalated into the film with a polymer electrolyte. We systematically demonstrate this difference in the electrostatic and electrochemical processes, by comparing doped carrier density, lattice deformation behavior, and time constant of the phase transitions. PMID:27502546

  2. Optically transparent thin-film transistors based on 2D multilayer MoS2 and indium zinc oxide electrodes

    NASA Astrophysics Data System (ADS)

    Kwon, Junyeon; Hong, Young Ki; Kwon, Hyuk-Jun; Park, Yu Jin; Yoo, Byungwook; Kim, Jiwan; Grigoropoulos, Costas P.; Oh, Min Suk; Kim, Sunkook

    2015-01-01

    We report on optically transparent thin film transistors (TFTs) fabricated using multilayered molybdenum disulfide (MoS2) as the active channel, indium tin oxide (ITO) for the back-gated electrode and indium zinc oxide (IZO) for the source/drain electrodes, respectively, which showed more than 81% transmittance in the visible wavelength. In spite of a relatively large Schottky barrier between MoS2 and IZO, the n-type behavior with a field-effect mobility (μeff) of 1.4 cm2 V-1 s-1 was observed in as-fabricated transparent MoS2 TFT. In order to enhance the performances of transparent MoS2 TFTs, a picosecond pulsed laser was selectively irradiated onto the contact region of the IZO electrodes. Following laser annealing, μeff increased to 4.5 cm2 V-1 s-1, and the on-off current ratio (Ion/Ioff) increased to 104, which were attributed to the reduction of the contact resistance between MoS2 and IZO.

  3. Differentially regulated proteins in Prevotella intermedia after oxidative stress analyzed by 2D electrophoresis and mass spectrometry.

    PubMed

    Santos, Simone G; Diniz, Cláudio G; Silva, Vânia L; Lima, Francisca L; Andrade, Hélida M; Chapeaurouge, Donat A; Perales, Jonas; Serufo, José Carlos; Carvalho, Maria Auxiliadora R; Farias, Luiz M

    2012-02-01

    Prevotella intermedia is a rod-shaped, Gram-negative anaerobic bacterium found in human indigenous microbiota that plays an important role in opportunistic infections. The successful colonization depends on the ability of anaerobes to respond to oxidative stress (OS) in oxygenated tissues as well as to resist oxidative events from the host immune system until anaerobic conditions are present at the infection site. As knowledge of the mechanisms of protection against OS in Prevotella is limited, studies are needed to clarify aspects of molecular biology, physiology and ecology of this bacterium. The aim of this study was to access the proteins differentially regulated in P. intermedia after exposure to molecular oxygen by using two-dimensional gel electrophoresis (2DE) associated with the approach of MALDI-TOF/TOF Tandem Mass Spectrometry. The identity of the protein was evaluated by database search for homologous genomic sequences of P. intermedia strain 17 (TIGR). Twenty five out of 72 proteins found were identified as up-regulated (17) or down-regulated (9). These proteins were related to a variety of metabolic process, some of which could be associated to antioxidant and redox regulatory roles. Our data indicate that OS may stimulate an adaptive response in P. intermedia whose effect on its biology may be evidenced by the increase in aerotolerance and changes in protein abundance in the oxygen adapted cells. PMID:22193554

  4. Static and Dynamical Structural Investigations of Metal-Oxide Nanocrystals by Powder X-ray Diffraction: Colloidal Tungsten Oxide as a Case Study.

    PubMed

    Caliandro, Rocco; Sibillano, Teresa; Belviso, B Danilo; Scarfiello, Riccardo; Hanson, Jonathan C; Dooryhee, Eric; Manca, Michele; Cozzoli, P Davide; Giannini, Cinzia

    2016-03-01

    We have developed a general X-ray powder diffraction (XPD) methodology for the simultaneous structural and compositional characterization of inorganic nanomaterials. The approach is validated on colloidal tungsten oxide nanocrystals (WO3-x NCs), as a model polymorphic nanoscale material system. Rod-shaped WO3-x NCs with different crystal structure and stoichiometry are comparatively investigated under an inert atmosphere and after prolonged air exposure. An initial structural model for the as-synthesized NCs is preliminarily identified by means of Rietveld analysis against several reference crystal phases, followed by atomic pair distribution function (PDF) refinement of the best-matching candidates (static analysis). Subtle stoichiometry deviations from the corresponding bulk standards are revealed. NCs exposed to air at room temperature are monitored by XPD measurements at scheduled time intervals. The static PDF analysis is complemented with an investigation into the evolution of the WO3-x NC structure, performed by applying the modulation enhanced diffraction technique to the whole time series of XPD profiles (dynamical analysis). Prolonged contact with ambient air is found to cause an appreciable increase in the static disorder of the O atoms in the WO3-x NC lattice, rather than a variation in stoichiometry. The time behavior of such structural change is identified on the basis of multivariate analysis. PMID:26756645

  5. Large-scale fabrication of 2-D nanoporous graphene using a thin anodic aluminum oxide etching mask.

    PubMed

    Lee, Jae-Hyun; Jang, Yamujin; Heo, Keun; Lee, Jeong-Mi; Choi, Soon Hyung; Joo, Won-Jae; Hwang, Sung Woo; Whang, Dongmok

    2013-11-01

    A large-scale nanoporous graphene (NPG) fabrication method via a thin anodic aluminum oxide (AAO) etching mask is presented in this paper. A thin AAO film is successfully transferred onto a hydrophobic graphene surface under no external force. The AAO film is completely stacked on the graphene due to the van der Waals force. The neck width of the NPG can be controlled ranging from 10 nm to 30 nm with different AAO pore widening times. Extension of the NPG structure is demonstrated on a centimeter scale up to 2 cm2. AAO and NPG structures are characterized using optical microscopy (OM), Raman spectroscopy and field-emission scanning electron microscopy (FE-SEM). A field effect transistor (FET) is realized by using NPG. Its electrical characteristics turn out to be different from that of pristine graphene, which is due to the periodic nanostructures. The proposed fabrication method could be adapted to a future graphene-based nano device. PMID:24245263

  6. The Oxidation State of Tungsten in Iron Bearing and Iron Free Silicate Glasses: Results from W L-Edge Xanes Measurements

    NASA Technical Reports Server (NTRS)

    Danielson, Lisa R.; Righter, K.; Sutton S.; Newville, M.; Le, L.

    2007-01-01

    Tungsten is important in constraining core formation of the Earth because this element is a moderately siderophile element (depleted approx. 10 relative to chondrites) and, as a member of the Hf-W isotopic system, it is useful in constraining the timing of core formation. A number of previous experimental studies have been carried out to determine the silicate solubility and metal-silicate partitioning behavior of W, including its concomitant oxidation state. However, results of previous studies (figure 1) are inconsistent on whether W occurs as W(4+) or W(6+).

  7. Properties of tungsten oxide thin films formed by ion-plasma and laser deposition methods for MOSiC-based hydrogen sensors

    SciTech Connect

    Fominski, V. Y.; Grigoriev, S. N.; Romanov, R. I.; Zuev, V. V.; Grigoriev, V. V.

    2012-03-15

    Thin-film structures based on gas-sensitive tungsten oxide and catalytic platinum are fabricated by room-temperature deposition on a silicon carbide wafer using pulsed laser and ion-plasma methods. Oxide layer annealing in air to 600 Degree-Sign C caused the formation of microstructured and nanostructured crystalline states depending on the deposition conditions. Structural differences affect the electrical parameters and the stability of characteristics. The maximum response to hydrogen is detected in the structure fabricated by depositing a low-energy laser-induced flow of tungsten atoms in oxygen. The voltage shift of the currentvoltage curves for 2% H{sub 2} in air at 350 Degree-Sign C was 4.6 V at a current of {approx}10 {mu}A. The grown structures' metastability caused a significant decrease in the shift after long-term cyclic testing. The most stable shifts of {approx}2 V at positive bias on the Pt contact were detected for oxide films deposited by ion-plasma sputtering.

  8. Computational Studies of Condensed Matter Systems: Manganese Vanadium Oxide and 2D attractive Hubbard model with spin-dependent disorder

    NASA Astrophysics Data System (ADS)

    Nanguneri, Ravindra

    -dependent disorder. Further, the finite temperature phase diagram for the 2D attractive fermion Hubbard model with spin-dependent disorder is also considered within BdG mean field theory. Three types of disorder are studied. In the first, only one species is coupled to a random site energy; in the second, the two species both move in random site energy landscapes which are of the same amplitude, but different realizations; and finally, in the third, the disorder is in the hopping rather than the site energy. For all three cases we find that, unlike the case of spin-symmetric randomness, where the energy gap and average order parameter do not vanish as the disorder strength increases, a critical disorder strength exists separating distinct phases. In fact, the energy gap and the average order parameter vanish at distinct transitions, Vcgap and Vc op, allowing for a gapless superconducting (gSC) phase. The gSC phase becomes smaller with increasing temperature, until it vanishes at a temperature T*.

  9. Tin-tungsten mineralizing processes in tungsten vein deposits: Panasqueira, Portugal

    NASA Astrophysics Data System (ADS)

    Lecumberri-Sanchez, P.; Pinto, F.; Vieira, R.; Wälle, M.; Heinrich, C. A.

    2015-12-01

    Tungsten has a high heat resistance, density and hardness, which makes it widely applied in industry (e.g. steel, tungsten carbides). Tungsten deposits are typically magmatic-hydrothermal systems. Despite the economic significance of tungsten, there are no modern quantitative analytical studies of the fluids responsible for the formation of its highest-grade deposit type (tungsten vein deposits). Panasqueira (Portugal) is a tungsten vein deposit, one of the leading tungsten producers in Europe and one of the best geologically characterized tungsten vein deposits. In this study, compositions of the mineralizing fluids at Panasqueira have been determined through combination of detailed petrography, microthermometric measurements and LA-ICPMS analyses, and geochemical modeling has been used to determine the processes that lead to tungsten mineralization. We characterized the fluids related to the various mineralizing stages in the system: the oxide stage (tin and tungsten mineralization), the sulfide stage (chalcopyrite and sphalerite mineralization) and the carbonate stage. Thus, our results provide information on the properties of fluids related with specific paragenetic stages. Furthermore we used those fluid compositions in combination with host rock mineralogy and chemistry to evaluate which are the controlling factors in the mineralizing process. This study provides the first quantitative analytical data on fluid composition for tungsten vein deposits and evaluates the controlling mineralization processes helping to determine the mechanisms of formation of the Panasqueira tin-tungsten deposit and providing additional geochemical constraints on the local distribution of mineralization.

  10. Freestanding graphene paper decorated with 2D-assembly of Au@Pt nanoparticles as flexible biosensors to monitor live cell secretion of nitric oxide.

    PubMed

    Zan, Xiaoli; Fang, Zheng; Wu, Jin; Xiao, Fei; Huo, Fengwei; Duan, Hongwei

    2013-11-15

    We report the development of a new type of flexible electrochemical biosensors based on graphene paper loaded with closely-packed Au@Pt core-shell nanoparticles as a freestanding cell culture substrate for real-time monitoring cell secretion of nitric oxide. The hybrid electrode was fabricated through a modular approach in which 2D-assembly of nanoparticles formed at the oil-water interface was transferred onto graphene paper by dip-coating. We have shown that the independently optimized metal nanostructures and graphene paper were integrated into functional electrodes with high electrocatalytic activity. When used for the detection of nitric oxide, the flexible electrodes have demonstrated high sensitivity, a wide linear range, and a low detection limit, which, in combination with its biocompatibility, offer unique opportunities for the real-time monitoring of nitric oxide secretion by human endothelial vein cells grown on the electrode. These interesting findings collectively demonstrate the potential of our modular approach for designing high-performance flexible electrodes with tailored surface properties.

  11. Cyclic Nanostructures of Tungsten Oxide (WO3)n  (n = 2–6) as NOx Gas Sensor: A Theoretical Study

    PubMed Central

    Izadyar, Mohammad; Jamsaz, Azam

    2014-01-01

    Today's WO3-based gas sensors have received a lot of attention, because of important role as a sensitive layer for detection of the small quantities of  NOx. In this research, a theoretical study has been done on the sensing properties of different cyclic nanoclusters of (WO3)n  (n = 2–6) for NOx  (x = 1,2) gases. Based on the calculated adsorption energies by B3LYP and X3LYP functionals, from the different orientations of  NOx molecule on the tungsten oxide clusters, O–N⋯W was preferred. Different sizes of the mentioned clusters have been analyzed and W2O6 cluster was chosen as the best candidate for NOx detection from the energy viewpoint. Using the concepts of the chemical hardness and electronic charge transfer, some correlations between the energy of adsorption and interaction energy have been established. These analyses confirmed that the adsorption energy will be boosted with charge transfer enhancement. However, the chemical hardness relationship is reversed. Finally, obtained results from the natural bond orbital and electronic density of states analysis confirmed the electronic charge transfer from the adsorbates to WO3 clusters and Fermi level shifting after adsorption, respectively. The last parameter confirms that the cyclic clusters of tungsten oxide can be used as NOx gas sensors. PMID:25544841

  12. A single-stage functionalization and exfoliation method for the production of graphene in water: stepwise construction of 2D-nanostructured composites with iron oxide nanoparticles.

    PubMed

    Ihiawakrim, Dris; Ersen, Ovidiu; Melin, Frédéric; Hellwig, Petra; Janowska, Izabela; Begin, Dominique; Baaziz, Walid; Begin-Colin, Sylvie; Pham-Huu, Cuong; Baati, Rachid

    2013-10-01

    A practically simple top-down process for the exfoliation of graphene (GN) and few-layer graphene (FLG) from graphite is described. We have discovered that a biocompatible amphiphilic pyrene-based hexahistidine peptide is able to exfoliate, functionalize, and dissolve few layer graphene flakes in pure water under exceptionally mild, sustainable and virtually innocuous low intensity cavitation conditions. Large area functionalized graphene flakes with the hexahistidine oligopeptide (His₆-TagGN = His₆@GN) have been produced efficiently at room temperature and characterized by TEM, Raman, and UV spectroscopy. Conductivity experiments carried out on His₆-TagGN samples revealed superior electric performances as compared to reduced graphene oxide (rGO) and non-functionalized graphene, demonstrating the non-invasive features of our non-covalent functionalization process. We postulated a rational exfoliation mechanism based on the intercalation of the peptide amphiphile under cavitational chemistry. We also demonstrated the ability of His6-TagGN nanoassemblies to self-assemble spontaneously with inorganic iron oxide nanoparticles generating magnetic two-dimensional (2D) His₆-TagGN/Fe₃O₄ nanocomposites under mild and non-hydrothermal conditions. The set of original experiments described here open novel perspectives in the facile production of water dispersible high quality GN and FLG sheets that will improve and facilitate the interfacing, processing and manipulation of graphene for promising applications in catalysis, nanocomposite construction, integrated nanoelectronic devices and bionanotechnology.

  13. Observation of compensation effects during the thermal dissolution of aluminum oxide layers on tungsten and molybdenum <111> and on tungsten ?110? in the presence of electric fields

    NASA Astrophysics Data System (ADS)

    Vanselow, R.; Pederson, L. R.

    1984-05-01

    Aluminum oxide layer dissolution was studied between 700 and 1200 K in the substrate areas of W<111>, Mo<111>, and on W{110} by means of FEM. Varying the electric field strength, F, between +45 and {+105 MV}/{cm}, two types of dissolution could be observed: dissolution by surface diffusion (low F's) and dissolution by ion desorption (high F's). It is assumed that aluminum suboxides — preferentially AlO — are involved in the dissolution processes. The preexponential factors, AF, of an Arrhenius-Frenkel type equation were measured as a function of F. The field dependence of AF is determined by the dissolution mechanism: (a) dissolution by diffusion: log A 0F = log A 00 - {ΔμF}/{2.3k ∗T } (μ  molecular dipole moment, ∗T ≡ isokinetic for W<111>, log A00 = - 6.0 and ∗T = 940 K; for Mo<111>, log A00 = - 3.1 and ∗T = 860 K; and (b) dissolution by ion desorption: log A +F = log A +0 + {n {3}/{2}e {3}/{2}F {1}/{2}}/{2.3k ∗T }; for A+0 = - 22 and ∗T = 1200 K; for W<111>, log A+0 = - 21 and ∗T = 1200 K. Using earlier proposed safeguards, isokinetic relationships (compensation effects) could be established for each of the two dissolution processes. The coordinates of the isokinetic points have the following average values: log∗A 00 = 2.5 and ∗T = 920 K for diffusion; log∗A +0 = - 1 and ∗T = 1240 K for ion desorption. The entropy changes (at T = ∗T , zero field strength, and unit pressure) for the phase changes: solid layer → diffusion layer and solid layer → ion gas, are of the order of {30 cal}/{K} · mol and {90 cal}/{K} · mol, respectively. The two dissolution mechanisms can be described by the following Arrhenius-Frenkel type equations: τ 0F = ∗A 00exp[ {- (E 00 + ΔμF) }/{k ∗T }] exp[( {E 00 + ΔμF) }/{kT}] for diffusion and τ +F = ∗A +0exp[ {- (E +0 - n {3}/{2}e {3}/{2}F {1}/{2}) }/{k ∗T }] exp[( {E +0 - n {3}/{2}e {3}/{2}F {1}/{2}) }/{kT}] for ion desorption.

  14. The Oxidation State of Tungsten in Iron Bearing and Iron Free Silicate Glasses: Results from W L-Edge XANES Measurements

    SciTech Connect

    Danielson, L.R.; Righter, K.; Sutton, S.; Newville, M.; Le, L.

    2007-03-06

    Knowledge of the oxidation state of W over a wide range of fO{sub 2} is critical to understanding the oxidation state of the mantle and core formation processes. W occurs as W6+ above {approx}IW-1. The transition between W{sup 4+} and W{sup 6+} occurs just below IW-1. Tungsten is important in constraining core formation of the Earth because this element is a moderately siderophile element (depleted {approx} 10 relative to chondrites) and, as a member of the Hf-W isotopic system, it is useful in constraining the timing of core formation. A number of previous experimental studies have been carried out to determine the silicate solubility and metal-silicate partitioning behavior of W, including its concomitant oxidation state. However, results of previous studies (Fig. 1) are inconsistent on whether W occurs as W4+ or W{sup 6+}. It is assumed that W{sup 4+} is the cation valence relevant to core formation. Given the sensitivity to silicate composition of high valence cations, knowledge of the oxidation state of W over a wide range of fO{sub 2} is critical to understanding the oxidation state of the mantle and core formation processes. This study seeks to measure the W valence and change in valence state over the range of fO{sub 2} most relevant to core formation, around IW-2.

  15. A single-stage functionalization and exfoliation method for the production of graphene in water: stepwise construction of 2D-nanostructured composites with iron oxide nanoparticles

    NASA Astrophysics Data System (ADS)

    Ihiawakrim, Dris; Ersen, Ovidiu; Melin, Frédéric; Hellwig, Petra; Janowska, Izabela; Begin, Dominique; Baaziz, Walid; Begin-Colin, Sylvie; Pham-Huu, Cuong; Baati, Rachid

    2013-09-01

    A practically simple top-down process for the exfoliation of graphene (GN) and few-layer graphene (FLG) from graphite is described. We have discovered that a biocompatible amphiphilic pyrene-based hexahistidine peptide is able to exfoliate, functionalize, and dissolve few layer graphene flakes in pure water under exceptionally mild, sustainable and virtually innocuous low intensity cavitation conditions. Large area functionalized graphene flakes with the hexahistidine oligopeptide (His6-TagGN = His6@GN) have been produced efficiently at room temperature and characterized by TEM, Raman, and UV spectroscopy. Conductivity experiments carried out on His6-TagGN samples revealed superior electric performances as compared to reduced graphene oxide (rGO) and non-functionalized graphene, demonstrating the non-invasive features of our non-covalent functionalization process. We postulated a rational exfoliation mechanism based on the intercalation of the peptide amphiphile under cavitational chemistry. We also demonstrated the ability of His6-TagGN nanoassemblies to self-assemble spontaneously with inorganic iron oxide nanoparticles generating magnetic two-dimensional (2D) His6-TagGN/Fe3O4 nanocomposites under mild and non-hydrothermal conditions. The set of original experiments described here open novel perspectives in the facile production of water dispersible high quality GN and FLG sheets that will improve and facilitate the interfacing, processing and manipulation of graphene for promising applications in catalysis, nanocomposite construction, integrated nanoelectronic devices and bionanotechnology.A practically simple top-down process for the exfoliation of graphene (GN) and few-layer graphene (FLG) from graphite is described. We have discovered that a biocompatible amphiphilic pyrene-based hexahistidine peptide is able to exfoliate, functionalize, and dissolve few layer graphene flakes in pure water under exceptionally mild, sustainable and virtually innocuous low

  16. Enhanced Collective Magnetic Properties in 2D Monolayers of Iron Oxide Nanoparticles Favored by Local Order and Local 1D Shape Anisotropy.

    PubMed

    Toulemon, Delphine; Liu, Yu; Cattoën, Xavier; Leuvrey, Cédric; Bégin-Colin, Sylvie; Pichon, Benoit P

    2016-02-16

    Magnetic nanoparticle arrays represent a very attractive research field because their collective properties can be efficiently modulated as a function of the structure of the assembly. Nevertheless, understanding the way dipolar interactions influence the intrinsic magnetic properties of nanoparticles still remains a great challenge. In this study, we report on the preparation of 2D assemblies of iron oxide nanoparticles as monolayers deposited onto substrates. Assemblies have been prepared by using the Langmuir-Blodgett technique and the SAM assisted assembling technique combined to CuAAC "click" reaction. These techniques afford to control the formation of well-defined monolayers of nanoparticles on large areas. The LB technique controls local ordering of nanoparticles, while adjusting the kinetics of CuAAC "click" reaction strongly affects the spatial arrangement of nanoparticles in monolayers. Fast kinetics favor disordered assemblies while slow kinetics favor the formation of chain-like structures. Such anisotropic assemblies are induced by dipolar interactions between nanoparticles as no magnetic field is applied and no solvent evaporation is performed. The collective magnetic properties of monolayers are studied as a function of average interparticle distance, local order and local shape anisotropy. We demonstrate that local control on spatial arrangement of nanoparticles in monolayers significantly strengthens dipolar interactions which enhances collective properties and results in possible super ferromagnetic order. PMID:26807596

  17. VIIRS S-NPP Nighttime DNB Spectral Response Function (SRF): The At-launch Characteristics and How the SRF Changes with Time Due to Tungsten Oxides Chromaticity

    NASA Astrophysics Data System (ADS)

    Guenther, B.; Lei, N.; Moeller, C.

    2015-12-01

    The VIIRS Day-Night Band (DNB) is designed with 3 gain stages: Low (LGS), Mid (MGS) and High (HGS) to span bright daytime to moonlit night earth scene signal levels. The published at-launch DNB relative spectral response (RSR) is based upon the LGS spectral measurements, since it was well measured in the pre-launch test program and the LGS can be calibrated by the on-board solar diffuser (MGS and HGS saturate on the SD). The LGS RSR however does not fully represent the spectral characteristics of nighttime DNB data from the MGS and HGS. Nighttime data users who apply the detailed DNB spectral characteristics in their analyses should use modulated RSR appropriate to the MGS and HGS observations. The RSR modulation is due to spectral darkening of the 4 mirrors of the S-NPP VIIRS telescope, which were contaminated with tungsten oxides in fabrication. These tungsten oxides are 'in family' with transition lenses on eyeglasses that darken when exposed to sunlight but do not recover when VIIRS goes into darkness because VIIRS in space is in a vacuum (transition lenses require atmospheric oxygen to recover). The on-going mirror darkening has caused a time-dependent shift in DNB RSR towards blue wavelengths. This presentation will provide access to the correct RSR to use for S-NPP DNB nighttime data over the mission time on-orbit. The changes in characteristics will be described in engineering terms to facilitate clear user understanding of how to handle RSR for nighttime observations over the mission lifetime.

  18. The formation of a hybrid structure from tungsten selenide and oxide plates for a hydrogen-evolution electrocatalyst

    NASA Astrophysics Data System (ADS)

    Fominski, V. Yu.; Grigoriev, S. N.; Romanov, R. I.; Volosova, M. A.; Grunin, A. I.; Teterina, G. D.

    2016-06-01

    It has been found that the pulsed laser deposition of a thin tungsten selenide film, followed by thermal treatment at 550°C in an Ar + O2 mixture of gases, results in the formation of a hybrid structure that is made up of ultrathin WSe2 and WO3- y platelets. The structural and size characteristics of the nanoplatelets deposited on microcrystalline graphite provide the effective hydrogen evolution reaction in a 0.5 M H2SO4 solution, with the cathode current made about seven times higher at a potential of-100 mV and the slope of the Tafel characteristic reduced from 340 to 90 mV/dec.

  19. Tailoring the conduction band of titanium oxide by doping tungsten for efficient electron injection in a sensitized photoanode.

    PubMed

    Cant, Alex M; Huang, Fuzhi; Zhang, Xiao Li; Chen, Yang; Cheng, Yi-Bing; Amal, Rose

    2014-04-01

    Aiming to overcome the current limits for dye-sensitized solar cells (DSSC) to reach a higher solar energy conversion efficiency, this work set out to investigate the feasibility of combining a variety of preparation techniques that can finely tailor the optical and electrochemical properties of the photoanode material. The obtained tungsten doped mesoporous titania spheres exhibited significant enhancements of photocurrent and open-circuit voltage leading to an over 15% increase in cell efficiency. With a single layer 12 μm film, the W-doped photoanode reached a solar energy conversion efficiency of 8.9% which is far greater than a 5.7% efficiency obtained by the photoanode film prepared from Degussa P25 TiO2 nanoparticles. This was greatly attributed to the superior light scattering effect from the mesostructure and the increased electron injection driving-force from the down-shifted conduction band after doping.

  20. Codoping of zinc and tungsten for practical high-performance amorphous indium-based oxide thin film transistors

    NASA Astrophysics Data System (ADS)

    Kizu, Takio; Mitoma, Nobuhiko; Miyanaga, Miki; Awata, Hideaki; Nabatame, Toshihide; Tsukagoshi, Kazuhito

    2015-09-01

    Using practical high-density sputtering targets, we investigated the effect of Zn and W codoping on the thermal stability of the amorphous film and the electrical characteristics in thin film transistors. zinc oxide is a potentially conductive component while W oxide is an oxygen vacancy suppressor in oxide films. The oxygen vacancy from In-O and Zn-O was suppressed by the W additive because of the high oxygen bond dissociation energy. With controlled codoping of W and Zn, we demonstrated a high mobility with a maximum mobility of 40 cm2/V s with good stability under a negative bias stress in InWZnO thin film transistors.

  1. The oxidation state of tungsten in iron bearing and iron free silicate glasses: Initial results from W L-edge XANES measurements

    NASA Astrophysics Data System (ADS)

    Danielson, L. R.; Righter, K.; Sutton, S.; Newville, M.; Le, L.

    2006-12-01

    Tungsten is important in constraining core formation of the Earth because this element is a moderately siderophile element (depleted ~ 10 relative to chondrites) and, as a member of the Hf-W isotopic system, it is useful in constraining the timing of core formation. A number of experimental studies have been carried out to determine the silicate solubility and metal-silicate partitioning behavior of W, including its concomitant oxidation state. However, results are inconsistent on whether W occurs as W^{4+} or W^{6+}. Results of Hillgren et al. (1996) and Walter and Thibault (1995) suggest W6+ for oxygen fugacities of IW-1 to -2, whereas Ertel et al. (1996) show W^{4+} for all oxygen fugacities below IW-1. The multiple linear regression analyses of Schmitt et al. (1989) (IW to IW-3) support W^{6+}, while similar analyses by Jones (1998), Lauer and Jones (1999), and Wade and Wood (2005) support W^{4+}, though it was suggested past discrepancies were due to iron-bearing vs. iron free systems. It is assumed that W^{4+} is the cation valence relevant to core formation (Jaeger and Drake, 2000). Given the sensitivity to silicate composition of high valence cations (Jaeger and Drake, 2000), knowledge of the oxidation state of W over a wide range of fO2 is critical to understanding the oxidation state of the mantle and core formation processes. Controlled fO2 experiments were carried out using two compositions to determine the effects of iron content. Experiments were conducted at 1300 °C, for durations of 24 to 72 hours, and air quenched. One series was conducted using the An-Di eutectic, from log fO2 -7.25 to -18. Experiments using an ankaramite starting composition were conducted from log fO2 -1.65 to -18.3. Experiments were doped with 1wt% of WO3. For both starting compositions, at IW-1, one set of experiments was doped with 1wt% of WO2, and at IW+1, one set of experiments was quenched in water. Analyses were conducted using the X-ray absorption near edge structure

  2. Effect of lithium-ion diffusibility on interfacial resistance of LiCoO2 thin film electrode modified with lithium tungsten oxides

    NASA Astrophysics Data System (ADS)

    Hayashi, Tetsutaro; Miyazaki, Takamichi; Matsuda, Yasutaka; Kuwata, Naoaki; Saruwatari, Motoaki; Furuichi, Yuki; Kurihara, Koji; Kuzuo, Ryuichi; Kawamura, Junichi

    2016-02-01

    To investigate the contribution of lithium-ion diffusibility of lithium tungsten oxides (LWOs) to low interfacial resistance, we fabricate thin-film electrodes of 6Li-enriched LiCoO2 (6LCO) modified with various structure-types of 6Li-enriched LWOs by pulsed laser deposition. The electrodes are subjected to X-ray diffraction (XRD), electrochemical impedance spectroscopy (EIS), and secondary-ion mass spectrometry (SIMS) analyses. XRD reveals that the LWO layers have Li2WO4 structure with rhombohedral and tetragonal symmetries and amorphous states. EIS shows that the lowest interfacial resistance of the positive electrodes is given by the amorphous state, followed in order by the tetragonal and the rhombohedral symmetry, and that the diffusion coefficients of lithium-ions in the electrodes increase in the same order. SIMS demonstrates that the fastest lithium-ion self-diffusibility into the LWOs is found in the amorphous state, followed in order by tetragonal and rhombohedral symmetry. Furthermore, the amorphous state LWO modification shows smooth lithium-ion diffusion between the LWO and LCO layers after the electrochemical test. Conversely, the rhombohedral LWO modification demonstrates congested lithium-ion diffusion between the LWO and LCO layers after the test. Thus, fast lithium-ion self-diffusibility into the LWO-modified LCO contributes to enhancing the diffusion of lithium-ions, resulting in the reduction of interfacial resistance.

  3. Switching operation and degradation of resistive random access memory composed of tungsten oxide and copper investigated using in-situ TEM

    PubMed Central

    Arita, Masashi; Takahashi, Akihito; Ohno, Yuuki; Nakane, Akitoshi; Tsurumaki-Fukuchi, Atsushi; Takahashi, Yasuo

    2015-01-01

    In-situ transmission electron microscopy (in-situ TEM) was performed to investigate the switching operation of a resistive random access memory (ReRAM) made of copper, tungsten oxide and titanium nitride (Cu/WOx/TiN). In the first Set (Forming) operation to initialize the device, precipitation appeared inside the WOx layer. It was presumed that a Cu conducting filament was formed, lowering the resistance (on-state). The Reset operation induced a higher resistance (the off-state). No change in the microstructure was identified in the TEM images. Only when an additional Reset current was applied after switching to the off-state could erasure of the filament be seen (over-Reset). Therefore, it was concluded that structural change relating to the resistance switch was localized in a very small area around the filament. With repeated switching operations and increasing operational current, the WOx/electrode interfaces became indistinct. At the same time, the resistance of the off-state gradually decreased. This is thought to be caused by Cu condensation at the interfaces because of leakage current through the area other than through the filament. This will lead to device degradation through mechanisms such as endurance failure. This is the first accelerated aging test of ReRAM achieved using in-situ TEM. PMID:26611856

  4. Codoping of zinc and tungsten for practical high-performance amorphous indium-based oxide thin film transistors

    SciTech Connect

    Kizu, Takio E-mail: TSUKAGOSHI.Kazuhito@nims.go.jp; Mitoma, Nobuhiko; Tsukagoshi, Kazuhito E-mail: TSUKAGOSHI.Kazuhito@nims.go.jp; Miyanaga, Miki; Awata, Hideaki; Nabatame, Toshihide

    2015-09-28

    Using practical high-density sputtering targets, we investigated the effect of Zn and W codoping on the thermal stability of the amorphous film and the electrical characteristics in thin film transistors. zinc oxide is a potentially conductive component while W oxide is an oxygen vacancy suppressor in oxide films. The oxygen vacancy from In-O and Zn-O was suppressed by the W additive because of the high oxygen bond dissociation energy. With controlled codoping of W and Zn, we demonstrated a high mobility with a maximum mobility of 40 cm{sup 2}/V s with good stability under a negative bias stress in InWZnO thin film transistors.

  5. Novel cerium-tungsten mixed oxide catalyst for the selective catalytic reduction of NO(x) with NH3.

    PubMed

    Shan, Wenpo; Liu, Fudong; He, Hong; Shi, Xiaoyan; Zhang, Changbin

    2011-07-28

    A novel Ce-W mixed oxide catalyst prepared by homogeneous precipitation method presented nearly 100% NO(x) conversion in a wide temperature range from 250 to 425 °C for the selective catalytic reduction of NO(x) with NH(3) under an extremely high GHSV of 500,000 h(-1).

  6. Aniso2D

    2005-07-01

    Aniso2d is a two-dimensional seismic forward modeling code. The earth is parameterized by an X-Z plane in which the seismic properties Can have monoclinic with x-z plane symmetry. The program uses a user define time-domain wavelet to produce synthetic seismograms anrwhere within the two-dimensional media.

  7. Towards 2D nanocomposites

    NASA Astrophysics Data System (ADS)

    Jang, Hyun-Sook; Yu, Changqian; Hayes, Robert; Granick, Steve

    2015-03-01

    Polymer vesicles (``polymersomes'') are an intriguing class of soft materials, commonly used to encapsulate small molecules or particles. Here we reveal they can also effectively incorporate nanoparticles inside their polymer membrane, leading to novel ``2D nanocomposites.'' The embedded nanoparticles alter the capacity of the polymersomes to bend and to stretch upon external stimuli.

  8. Mesh2d

    2011-12-31

    Mesh2d is a Fortran90 program designed to generate two-dimensional structured grids of the form [x(i),y(i,j)] where [x,y] are grid coordinates identified by indices (i,j). The x(i) coordinates alone can be used to specify a one-dimensional grid. Because the x-coordinates vary only with the i index, a two-dimensional grid is composed in part of straight vertical lines. However, the nominally horizontal y(i,j0) coordinates along index i are permitted to undulate or otherwise vary. Mesh2d also assignsmore » an integer material type to each grid cell, mtyp(i,j), in a user-specified manner. The complete grid is specified through three separate input files defining the x(i), y(i,j), and mtyp(i,j) variations.« less

  9. Assessment of C-phycocyanin effect on astrocytes-mediated neuroprotection against oxidative brain injury using 2D and 3D astrocyte tissue model

    PubMed Central

    Min, Seul Ki; Park, Jun Sang; Luo, Lidan; Kwon, Yeo Seon; Lee, Hoo Cheol; Jung Shim, Hyun; Kim, Il-Doo; Lee, Ja-Kyeong; Shin, Hwa Sung

    2015-01-01

    Drugs are currently being developed to attenuate oxidative stress as a treatment for brain injuries. C-phycocyanin (C-Pc) is an antioxidant protein of green microalgae known to exert neuroprotective effects against oxidative brain injury. Astrocytes, which compose many portions of the brain, exert various functions to overcome oxidative stress; however, little is known about how C-Pc mediates the antioxidative effects of astrocytes. In this study, we revealed that C-Pc intranasal administration to the middle cerebral artery occlusion (MCAO) rats ensures neuroprotection of ischemic brain by reducing infarct size and improving behavioral deficits. C-Pc also enhanced viability and proliferation but attenuated apoptosis and reactive oxygen species (ROS) of oxidized astrocytes, without cytotoxicity to normal astrocytes and neurons. To elucidate how C-Pc leads astrocytes to enhance neuroprotection and repair of ischemia brain, we firstly developed 3D oxidized astrocyte model. C-Pc had astrocytes upregulate antioxidant enzymes such as SOD and catalase and neurotrophic factors BDNF and NGF, while alleviating inflammatory factors IL-6 and IL-1β and glial scar. Additionally, C-Pc improved viability of 3D oxidized neurons. In summary, C-Pc was concluded to activate oxidized astrocytes to protect and repair the ischemic brain with the combinatorial effects of improved antioxidative, neurotrophic, and anti-inflammatory mechanisms. PMID:26399322

  10. Assessment of C-phycocyanin effect on astrocytes-mediated neuroprotection against oxidative brain injury using 2D and 3D astrocyte tissue model.

    PubMed

    Min, Seul Ki; Park, Jun Sang; Luo, Lidan; Kwon, Yeo Seon; Lee, Hoo Cheol; Shim, Hyun Jung; Kim, Il-Doo; Lee, Ja-Kyeong; Shin, Hwa Sung

    2015-01-01

    Drugs are currently being developed to attenuate oxidative stress as a treatment for brain injuries. C-phycocyanin (C-Pc) is an antioxidant protein of green microalgae known to exert neuroprotective effects against oxidative brain injury. Astrocytes, which compose many portions of the brain, exert various functions to overcome oxidative stress; however, little is known about how C-Pc mediates the antioxidative effects of astrocytes. In this study, we revealed that C-Pc intranasal administration to the middle cerebral artery occlusion (MCAO) rats ensures neuroprotection of ischemic brain by reducing infarct size and improving behavioral deficits. C-Pc also enhanced viability and proliferation but attenuated apoptosis and reactive oxygen species (ROS) of oxidized astrocytes, without cytotoxicity to normal astrocytes and neurons. To elucidate how C-Pc leads astrocytes to enhance neuroprotection and repair of ischemia brain, we firstly developed 3D oxidized astrocyte model. C-Pc had astrocytes upregulate antioxidant enzymes such as SOD and catalase and neurotrophic factors BDNF and NGF, while alleviating inflammatory factors IL-6 and IL-1β and glial scar. Additionally, C-Pc improved viability of 3D oxidized neurons. In summary, C-Pc was concluded to activate oxidized astrocytes to protect and repair the ischemic brain with the combinatorial effects of improved antioxidative, neurotrophic, and anti-inflammatory mechanisms. PMID:26399322

  11. 2D materials: to graphene and beyond.

    PubMed

    Mas-Ballesté, Rubén; Gómez-Navarro, Cristina; Gómez-Herrero, Julio; Zamora, Félix

    2011-01-01

    This review is an attempt to illustrate the different alternatives in the field of 2D materials. Graphene seems to be just the tip of the iceberg and we show how the discovery of alternative 2D materials is starting to show the rest of this iceberg. The review comprises the current state-of-the-art of the vast literature in concepts and methods already known for isolation and characterization of graphene, and rationalizes the quite disperse literature in other 2D materials such as metal oxides, hydroxides and chalcogenides, and metal-organic frameworks.

  12. Internal Photoemission Spectroscopy of 2-D Materials

    NASA Astrophysics Data System (ADS)

    Nguyen, Nhan; Li, Mingda; Vishwanath, Suresh; Yan, Rusen; Xiao, Shudong; Xing, Huili; Cheng, Guangjun; Hight Walker, Angela; Zhang, Qin

    Recent research has shown the great benefits of using 2-D materials in the tunnel field-effect transistor (TFET), which is considered a promising candidate for the beyond-CMOS technology. The on-state current of TFET can be enhanced by engineering the band alignment of different 2D-2D or 2D-3D heterostructures. Here we present the internal photoemission spectroscopy (IPE) approach to determine the band alignments of various 2-D materials, in particular SnSe2 and WSe2, which have been proposed for new TFET designs. The metal-oxide-2-D semiconductor test structures are fabricated and characterized by IPE, where the band offsets from the 2-D semiconductor to the oxide conduction band minimum are determined by the threshold of the cube root of IPE yields as a function of photon energy. In particular, we find that SnSe2 has a larger electron affinity than most semiconductors and can be combined with other semiconductors to form near broken-gap heterojunctions with low barrier heights which can produce a higher on-state current. The details of data analysis of IPE and the results from Raman spectroscopy and spectroscopic ellipsometry measurements will also be presented and discussed.

  13. Tungsten diffusion in silicon

    SciTech Connect

    De Luca, A.; Texier, M.; Burle, N.; Oison, V.; Pichaud, B.; Portavoce, A.; Grosjean, C.

    2014-01-07

    Two doses (10{sup 13} and 10{sup 15} cm{sup −2}) of tungsten (W) atoms were implanted in different Si(001) wafers in order to study W diffusion in Si. The samples were annealed or oxidized at temperatures between 776 and 960 °C. The diffusion profiles were measured by secondary ion mass spectrometry, and defect formation was studied by transmission electron microscopy and atom probe tomography. W is shown to reduce Si recrystallization after implantation and to exhibit, in the temperature range investigated, a solubility limit close to 0.15%–0.2%, which is higher than the solubility limit of usual metallic impurities in Si. W diffusion exhibits unusual linear diffusion profiles with a maximum concentration always located at the Si surface, slower kinetics than other metals in Si, and promotes vacancy accumulation close to the Si surface, with the formation of hollow cavities in the case of the higher W dose. In addition, Si self-interstitial injection during oxidation is shown to promote W-Si clustering. Taking into account these observations, a diffusion model based on the simultaneous diffusion of interstitial W atoms and W-Si atomic pairs is proposed since usual models used to model diffusion of metallic impurities and dopants in Si cannot reproduce experimental observations.

  14. Ultrasensitive electrochemical sensing platform for microRNA based on tungsten oxide-graphene composites coupling with catalyzed hairpin assembly target recycling and enzyme signal amplification.

    PubMed

    Shuai, Hong-Lei; Huang, Ke-Jing; Xing, Ling-Li; Chen, Ying-Xu

    2016-12-15

    An ultrasensitive electrochemical biosensor for microRNA (miRNA) is developed based on tungsten oxide-graphene composites coupling with catalyzed hairpin assembly target recycling and enzyme signal amplification. WO3-Gr is prepared by a simple hydrothermal method and then coupled with gold nanoparticles to act as a sensing platform. The thiol-terminated capture probe H1 is immobilized on electrode through Au-S interaction. In the presence of target miRNA, H1 opens its hairpin structure by hybridization with target miRNA. This hybridization can be displaced from the structure by another stable biotinylated hairpin DNA (H2), and target miRNA is released back to the sample solution for next cycle. Thus, a large amount of H1-H2 duplex is produced after the cyclic process. At this point, a lot of signal indicators streptavidin-conjugated alkaline phosphatase (SA-ALP) are immobilized on the electrode by the specific binding of avidin-biotin. Then, thousands of ascorbic acid, which is the enzymatic product of ALP, induces the electrochemical-chemical-chemical redox cycling to produce a strongly electrochemical response in the presence of ferrocene methanol and tris (2-carboxyethyl) phosphine. Under the optimal experimental conditions, the established biosensor can detect target miRNA down to 0.05fM (S/N=3) with a linear range from 0.1fM to 100pM, and discriminate target miRNA from mismatched miRNA with a high selectivity. PMID:27392235

  15. Ultrasensitive electrochemical sensing platform for microRNA based on tungsten oxide-graphene composites coupling with catalyzed hairpin assembly target recycling and enzyme signal amplification.

    PubMed

    Shuai, Hong-Lei; Huang, Ke-Jing; Xing, Ling-Li; Chen, Ying-Xu

    2016-12-15

    An ultrasensitive electrochemical biosensor for microRNA (miRNA) is developed based on tungsten oxide-graphene composites coupling with catalyzed hairpin assembly target recycling and enzyme signal amplification. WO3-Gr is prepared by a simple hydrothermal method and then coupled with gold nanoparticles to act as a sensing platform. The thiol-terminated capture probe H1 is immobilized on electrode through Au-S interaction. In the presence of target miRNA, H1 opens its hairpin structure by hybridization with target miRNA. This hybridization can be displaced from the structure by another stable biotinylated hairpin DNA (H2), and target miRNA is released back to the sample solution for next cycle. Thus, a large amount of H1-H2 duplex is produced after the cyclic process. At this point, a lot of signal indicators streptavidin-conjugated alkaline phosphatase (SA-ALP) are immobilized on the electrode by the specific binding of avidin-biotin. Then, thousands of ascorbic acid, which is the enzymatic product of ALP, induces the electrochemical-chemical-chemical redox cycling to produce a strongly electrochemical response in the presence of ferrocene methanol and tris (2-carboxyethyl) phosphine. Under the optimal experimental conditions, the established biosensor can detect target miRNA down to 0.05fM (S/N=3) with a linear range from 0.1fM to 100pM, and discriminate target miRNA from mismatched miRNA with a high selectivity.

  16. Kinetics of Coloration in Photochromic Tungsten(VI) Oxide/Silicon Oxycarbide/Silica Hybrid Xerogel: Insight into Cation Self-diffusion Mechanisms.

    PubMed

    Adachi, Kenta; Tokushige, Masataka; Omata, Kaoru; Yamazaki, Suzuko; Iwadate, Yoshiaki

    2016-06-01

    Silicon oxycarbide/silica composites with well-dispersed tungsten(VI) oxide (WO3) nanoparticles were obtained as transparent hybrid xerogels via an acid-catalyzed sol-gel process (hydrolysis/condensation polymerization) of 3-(triethoxysilyl)propyl methacrylate (TESPMA) and tetraethoxysilane (TEOS). The self-diffusion mechanism of alkali-metal cations and the kinetics of the photochromic coloration process in the WO3/TESPMA/TEOS hybrid xerogel systems have been systematically investigated. Under continuous UV illumination, a gradual color change (colorless → blue) corresponding to the reduction of W(6+) into W(5+) states in WO3 nanoparticles can be confirmed from the WO3/TESPMA/TEOS hybrid xerogels containing alkali-metal sulfates, although no coloration of the hybrid xerogel without alkali-metal sulfate was observed. The coloration behavior depended exclusively on a variety of alkali-metal cations present in the hybrid xerogel system. Furthermore, a detailed analysis of the self-diffusion mechanism confirmed that the alkali-metal cations electrostatically interact with a layer of unreacted silanol groups on the TESPMA/TEOS matrix surface, and subsequently pass through the interconnected pore network of the hybrid xerogel. More interestingly, in the context of an Arrhenius analysis, we found a good coincidence between the activation energies for alkali-metal cation self-diffusion and UV-induced coloration in the WO3/TESPMA/TEOS hybrid xerogel system containing the corresponding alkali-metal sulfate. It is experimentally obvious that the photochromic properties are dominated by the diffusion process of alkali-metal cations in the WO3/TESPMA/TEOS hybrid xerogel system. Such hybrid materials with cation-controlled photochromic properties will show promising prospects in applications demanding energy-efficient "smart windows" and "smart glasses". PMID:27159661

  17. Numerical Simulation of Stationary AC Tungsten Inert Gas Welding of Aluminum Plate in Consideration of Oxide Layer Cleaning

    NASA Astrophysics Data System (ADS)

    Tashiro, Shinichi; Tanaka, Manabu

    An unified numerical simulation model of AC TIG welding of the aluminum plate considering energy balance among the electrode, the arc and the base metal and employing an analytical model for calculating cleaning rate of the oxide layer has been developed for investigating heat transport properties and weld pool formation process in AC TIG welding of aluminum plate. As a result of this simulation, it was shown that although the heat flux from the arc onto the base metal increases in EN (Electrode Negative) phase due to the electron condensation, that in EP (Electrode Positive) phase conversely decreases because mainly of cooling caused by the electron emission. Furthermore, the validity of the simulation model was confirmed by comparing to experimental results such as the arc voltage, the area of cleaning zone and the shape of weld pool.

  18. Tungsten Filament Fire

    ERIC Educational Resources Information Center

    Ruiz, Michael J.; Perkins, James

    2016-01-01

    We safely remove the outer glass bulb from an incandescent lamp and burn up the tungsten filament after the glass is removed. This demonstration dramatically illustrates the necessity of a vacuum or inert gas for the environment surrounding the tungsten filament inside the bulb. Our approach has added historical importance since the incandescent…

  19. Tungsten filament fire

    NASA Astrophysics Data System (ADS)

    Ruiz, Michael J.; Perkins, James

    2016-05-01

    We safely remove the outer glass bulb from an incandescent lamp and burn up the tungsten filament after the glass is removed. This demonstration dramatically illustrates the necessity of a vacuum or inert gas for the environment surrounding the tungsten filament inside the bulb. Our approach has added historical importance since the incandescent light bulb is being replaced by compact fluorescent and LED lamps.

  20. High-Concentration Aqueous Dispersions of Nanoscale 2D Materials Using Nonionic, Biocompatible Block Copolymers.

    PubMed

    Mansukhani, Nikhita D; Guiney, Linda M; Kim, Peter J; Zhao, Yichao; Alducin, Diego; Ponce, Arturo; Larios, Eduardo; Yacaman, Miguel Jose; Hersam, Mark C

    2016-01-20

    Conditions for the dispersion of molybdenum disulfide (MoS2) in aqueous solution at concentrations up to 0.12 mg mL(-1) using a range of nonionic, biocompatible block copolymers (i.e., Pluronics and Tetronics) are identified. Furthermore, the optimal Pluronic dispersant for MoS2 is found to be effective for a range of other 2D materials such as molybdenum diselenide, tungsten diselenide, tungsten disulfide, tin selenide, and boron nitride.

  1. Enhancing the photoelectrochemical water splitting characteristics of titanium and tungsten oxide based materials via doping and sensitization

    NASA Astrophysics Data System (ADS)

    Gakhar, Ruchi

    To better utilize solar energy for clean energy production, efforts are needed to overcome the natural diurnal variation and the diffuse nature of sunlight. Photoelectrochemical (PEC) hydrogen generation by water splitting is a promising approach to harvest solar energy. Hydrogen gas is a clean and high energy capacity fuel. However, the solar-to-hydrogen conversion efficiency is determined mainly by the properties of the materials employed as photoanodes. Improving the power-conversion efficiency of PEC water splitting requires the design of inexpensive and efficient photoanodes that have strong visible light absorption, fast charge separation, and lower charge recombination rate. In the present study, PEC characteristics of various semiconducting photoelectrodes such as TiO2, WO3 and CuWO4 were investigated. Due to the inherent wide gap, such metal oxides absorb only ultraviolet radiation. Since ultraviolet radiation only composes of 4% of the sun's spectrum, the wide band gap results in lower charge collection and efficiency. Thusto improve optical absorption and charge separation, it is necessary to modify the band gap with low band gap materials.The two approaches followed for modification of band gap are doping and sensitization. Here, TiO2 and WO3 based photoanodes were sensitized with ternary quatum dots, while doping was the primary method utilized to investigate the modification of the band gap of CuWO4. The first part of this dissertation reports the synthesis of ternary quantum dot - sensitized titania nanotube array photoelectrodes. Ternary quantum dots with varying band gaps and composition (MnCdSe, ZnCdSe and CdSSe) were tethered to the surface of TiO2 nanotubes using succcessive ionic layer adsorption and reaction (SILAR) technique. The stoichiometry of ternary quantum dots was estimated to beMn0.095Cd0.95Se, Zn0.16Cd0.84Se and CdS0.54Se0.46. The effect of varying number of sensitization cycles and annealing temperature on optical and

  2. A Theoretical Study of Single-Atom Catalysis of CO Oxidation Using Au Embedded 2D h-BN Monolayer: A CO-Promoted O2 Activation

    PubMed Central

    Mao, Keke; Li, Lei; Zhang, Wenhua; Pei, Yong; Zeng, Xiao Cheng; Wu, Xiaojun; Yang, Jinlong

    2014-01-01

    The CO oxidation behaviors on single Au atom embedded in two-dimensional h-BN monolayer are investigated on the basis of first-principles calculations, quantum Born-Oppenheim molecular dynamic simulations (BOMD) and micro-kinetic analysis. We show that CO oxidation on h-BN monolayer support single gold atom prefers an unreported tri-molecular Eley-Rideal (E-R) reaction, where O2 molecule is activated by two pre-adsorbed CO molecules. The formed OCOAuOCO intermediate dissociates into two CO2 molecules synchronously, which is the rate-limiting step with an energy barrier of 0.47 eV. By using the micro-kinetic analysis, the CO oxidation following the tri-molecular E-R reaction pathway entails much higher reaction rate (1.43 × 105 s−1) than that of bimolecular Langmuir-Hinshelwood (L-H) pathway (4.29 s−1). Further, the quantum BOMD simulation at the temperature of 300 K demonstrates the complete reaction process in real time. PMID:24962006

  3. A theoretical study of single-atom catalysis of CO oxidation using Au embedded 2D h-BN monolayer: a CO-promoted O₂ activation.

    PubMed

    Mao, Keke; Li, Lei; Zhang, Wenhua; Pei, Yong; Zeng, Xiao Cheng; Wu, Xiaojun; Yang, Jinlong

    2014-01-01

    The CO oxidation behaviors on single Au atom embedded in two-dimensional h-BN monolayer are investigated on the basis of first-principles calculations, quantum Born-Oppenheim molecular dynamic simulations (BOMD) and micro-kinetic analysis. We show that CO oxidation on h-BN monolayer support single gold atom prefers an unreported tri-molecular Eley-Rideal (E-R) reaction, where O2 molecule is activated by two pre-adsorbed CO molecules. The formed OCOAuOCO intermediate dissociates into two CO2 molecules synchronously, which is the rate-limiting step with an energy barrier of 0.47 eV. By using the micro-kinetic analysis, the CO oxidation following the tri-molecular E-R reaction pathway entails much higher reaction rate (1.43 × 10(5) s(-1)) than that of bimolecular Langmuir-Hinshelwood (L-H) pathway (4.29 s(-1)). Further, the quantum BOMD simulation at the temperature of 300 K demonstrates the complete reaction process in real time. PMID:24962006

  4. Electrode potentials of tungsten in fused alkali chlorides

    NASA Astrophysics Data System (ADS)

    Ivanov, A. B.; Volkovich, V. A.; Poskryakov, D. A.; Vasin, B. D.; Griffiths, T. R.

    2016-09-01

    Anodic dissolution of tungsten was studied at 823-1173 K in the melts based on NaCl-CsCl, NaCl-KCl-CsCl and LiCl-KCl-CsCl eutectic mixtures. The process results in the formation of W(IV) ions. Prolonged contact with silica results in oxidation W(IV) ions and decreasing tungsten concentration in the electrolyte due to formation of volatile higher oxidation state chloro- and oxychloro-species. Tungsten electrode potentials were measured in NaCl-CsCl and NaCl-KCl-CsCl based melts using potentiometry.

  5. Element 74, the Wolfram Versus Tungsten Controversy

    SciTech Connect

    Holden,N.E.

    2008-08-11

    Two and a quarter centuries ago, a heavy mineral ore was found which was thought to contain a new chemical element called heavy stone (or tungsten in Swedish). A few years later, the metal was separated from its oxide and the new element (Z=74) was called wolfram. Over the years since that time, both the names wolfram and tungsten were attached to this element in various countries. Sixty years ago, IUPAC chose wolfram as the official name for the element. A few years later, under pressure from the press in the USA, the alternative name tungsten was also allowed by IUPAC. Now the original, official name 'wolfram' has been deleted by IUPAC as one of the two alternate names for the element. The history of this controversy is described here.

  6. Large-scale synthesis of ultrathin tungsten oxide nanowire networks: an efficient catalyst for aerobic oxidation of toluene to benzaldehyde under visible light.

    PubMed

    Bai, Hua; Yi, Wencai; Liu, Jingyao; Lv, Qing; Zhang, Qing; Ma, Qiang; Yang, Haifeng; Xi, Guangcheng

    2016-07-14

    As a very important chemical raw material, the selective formation of benzaldehyde from toluene at preparative or industrial levels requires the use of highly corrosive chlorine and high reaction temperatures, which severely corrodes equipment, pollutes the environment, and consumes a lot of energy. Herein, we report a robust and highly active catalyst for the benzaldehyde evolution reaction that is constructed by the surfactant-free growth of oxygen vacancy-rich W18O49 ultrathin nanowire networks. Under atmospheric pressure and visible-light irradiation, the new catalyst can selectively (92% selectivity) catalyze the aerobic oxidation of toluene to benzaldehyde with yields of above 95%.

  7. Large-scale synthesis of ultrathin tungsten oxide nanowire networks: an efficient catalyst for aerobic oxidation of toluene to benzaldehyde under visible light

    NASA Astrophysics Data System (ADS)

    Bai, Hua; Yi, Wencai; Liu, Jingyao; Lv, Qing; Zhang, Qing; Ma, Qiang; Yang, Haifeng; Xi, Guangcheng

    2016-07-01

    As a very important chemical raw material, the selective formation of benzaldehyde from toluene at preparative or industrial levels requires the use of highly corrosive chlorine and high reaction temperatures, which severely corrodes equipment, pollutes the environment, and consumes a lot of energy. Herein, we report a robust and highly active catalyst for the benzaldehyde evolution reaction that is constructed by the surfactant-free growth of oxygen vacancy-rich W18O49 ultrathin nanowire networks. Under atmospheric pressure and visible-light irradiation, the new catalyst can selectively (92% selectivity) catalyze the aerobic oxidation of toluene to benzaldehyde with yields of above 95%.As a very important chemical raw material, the selective formation of benzaldehyde from toluene at preparative or industrial levels requires the use of highly corrosive chlorine and high reaction temperatures, which severely corrodes equipment, pollutes the environment, and consumes a lot of energy. Herein, we report a robust and highly active catalyst for the benzaldehyde evolution reaction that is constructed by the surfactant-free growth of oxygen vacancy-rich W18O49 ultrathin nanowire networks. Under atmospheric pressure and visible-light irradiation, the new catalyst can selectively (92% selectivity) catalyze the aerobic oxidation of toluene to benzaldehyde with yields of above 95%. Electronic supplementary information (ESI) available: Experimental procedure, XRD patterns, TEM and HRTEM images, energy-dispersive X-ray spectra, UV-vis spectra, X-ray photoelectron spectroscopy (XPS), and EDS. See DOI: 10.1039/c6nr02949c

  8. Measurement of uptake and release of tritium by tungsten

    SciTech Connect

    Nakayama, M.; Torikai, Y.; Saito, M.; Penzhorn, R.D.; Isobe, K.; Yamanishi, T.; Kurishita, H.

    2015-03-15

    Tungsten is currently contemplated as plasma facing material for the divertor of future fusion machines. In this paper the uptake of tritium by tungsten and its release behavior have been investigated. Tungsten samples have been annealed at various temperatures and loaded at also different temperatures with deuterium containing 7.2 % tritium at a pressure of 1.2 kPa. A specific system was designed to assess the release of tritiated water and molecular tritium by the samples. Due to the rather low solubility of hydrogen isotopes in tungsten it is particularly important to be aware of the presence of hydrogen traps or thin oxide films. As shown in this work, traps or oxide films may affect the retention capability of tungsten and lead to significantly modified release properties. It became clear that there were capture sites that had different thermal stability and different capture intensity in tungsten after polishing, or oxide films that were grown on the surface of tungsten and had barrier effects.

  9. Gas-driven permeation of deuterium through tungsten and tungsten alloys

    DOE PAGES

    Buchenauer, Dean A.; Karnesky, Richard A.; Fang, Zhigang Zak; Ren, Chai; Oya, Yasuhisa; Otsuka, Teppei; Yamauchi, Yuji; Whaley, Josh A.

    2016-03-25

    Here, to address the transport and trapping of hydrogen isotopes, several permeation experiments are being pursued at both Sandia National Laboratories (deuterium gas-driven permeation) and Idaho National Laboratories (tritium gas- and plasma-driven tritium permeation). These experiments are in part a collaboration between the US and Japan to study the performance of tungsten at divertor relevant temperatures (PHENIX). Here we report on the development of a high temperature (≤1150 °C) gas-driven permeation cell and initial measurements of deuterium permeation in several types of tungsten: high purity tungsten foil, ITER-grade tungsten (grains oriented through the membrane), and dispersoid-strengthened ultra-fine grain (UFG) tungstenmore » being developed in the US. Experiments were performed at 500–1000 °C and 0.1–1.0 atm D2 pressure. Permeation through ITER-grade tungsten was similar to earlier W experiments by Frauenfelder (1968–69) and Zaharakov (1973). Data from the UFG alloy indicates marginally higher permeability (< 10×) at lower temperatures, but the permeability converges to that of the ITER tungsten at 1000 °C. The permeation cell uses only ceramic and graphite materials in the hot zone to reduce the possibility for oxidation of the sample membrane. Sealing pressure is applied externally, thereby allowing for elevation of the temperature for brittle membranes above the ductile-to-brittle transition temperature.« less

  10. Distinctive Finite Size Effects on the Phase Diagram and Metal-insulator Transitions of Tungsten-doped Vanadium(IV) Oxide

    SciTech Connect

    L Whittaker; T Wu; C Patridge; S Ganapathy; S Banerjee

    2011-12-31

    The influence of finite size in altering the phase stabilities of strongly correlated materials gives rise to the interesting prospect of achieving additional tunability of solid-solid phase transitions such as those involved in metal-insulator switching, ferroelectricity, and superconductivity. We note here some distinctive finite size effects on the relative phase stabilities of insulating (monoclinic) and metallic (tetragonal) phases of solid-solution W{sub x}V{sub 1-x}O{sub 2}. Ensemble differential scanning calorimetry and individual nanobelt electrical transport measurements suggest a pronounced hysteresis between metal {yields} insulator and insulator {yields} metal phase transformations. Both transitions are depressed to lower critical temperatures upon the incorporation of substitutional tungsten dopants but the impact on the former transition seems far more prominent. In general, the depression in the critical temperatures upon tungsten doping far exceeds corresponding values for bulk W{sub x}V{sub 1-x}O{sub 2} of the same composition. Notably, the depression in phase transition temperature saturates at a relatively low dopant concentration in the nanobelts, thought to be associated with the specific sites occupied by the tungsten substitutional dopants in these structures. The marked deviations from bulk behavior are rationalized in terms of a percolative model of the phase transition taking into account the nucleation of locally tetragonal domains and enhanced carrier delocalization that accompany W{sup 6+} doping in the W{sub x}V{sub 1-x}O{sub 2} nanobelts.

  11. Naturally Derived Iron Oxide Nanowires from Bacteria for Magnetically Triggered Drug Release and Cancer Hyperthermia in 2D and 3D Culture Environments: Bacteria Biofilm to Potent Cancer Therapeutic.

    PubMed

    Kumeria, Tushar; Maher, Shaheer; Wang, Ye; Kaur, Gagandeep; Wang, Luoshan; Erkelens, Mason; Forward, Peter; Lambert, Martin F; Evdokiou, Andreas; Losic, Dusan

    2016-08-01

    Iron oxide nanowires produced by bacteria (Mariprofundus ferrooxydans) are demonstrated as new multifunctional drug carriers for triggered therapeutics release and cancer hyperthmia applications. Iron oxide nanowires are obtained from biofilm waste in the bore system used to pump saline groundwater into the River Murray, South Australia (Australia) and processed into individual nanowires with extensive magnetic properties. The drug carrier capabilities of these iron oxide nanowires (Bac-FeOxNWs) are assessed by loading anticancer drug (doxorubicin, Dox) followed by measuring its elution under sustained and triggered release conditions using alternating magnetic field (AMF). The cytotoxicity of Bac-FeOxNWs assessed in 2D (96 well plate) and 3D (Matrigel) cell cultures using MDA-MB231-TXSA human breast cancer cells and mouse RAW 264.7 macrophage cells shows that these Bac-FeOxNWs are biocompatible even at concentrations as high as 250 μg/mL after 24 h of incubation. Finally, we demonstrate the capabilities of Bac-FeOxNWs as potential hyperthermia agent in 3D culture setup. Application of AMF increased the local temperature by 14 °C resulting in approximately 34% decrease in cell viability. Our results demonstrate that these naturally produced nanowires in the form of biofilm can efficiently act as drug carriers with triggered payload release and magnetothermal heating features for potential anticancer therapeutics applications. PMID:27428076

  12. High divergent 2D grating

    NASA Astrophysics Data System (ADS)

    Wang, Jin; Ma, Jianyong; Zhou, Changhe

    2014-11-01

    A 3×3 high divergent 2D-grating with period of 3.842μm at wavelength of 850nm under normal incidence is designed and fabricated in this paper. This high divergent 2D-grating is designed by the vector theory. The Rigorous Coupled Wave Analysis (RCWA) in association with the simulated annealing (SA) is adopted to calculate and optimize this 2D-grating.The properties of this grating are also investigated by the RCWA. The diffraction angles are more than 10 degrees in the whole wavelength band, which are bigger than the traditional 2D-grating. In addition, the small period of grating increases the difficulties of fabrication. So we fabricate the 2D-gratings by direct laser writing (DLW) instead of traditional manufacturing method. Then the method of ICP etching is used to obtain the high divergent 2D-grating.

  13. Visualization by neutron diffraction of 2D oxygen diffusion in the Sr(0.7)Ho(0.3)CoO(3-δ) cathode for solid-oxide fuel cells.

    PubMed

    Cascos, V; Martínez-Coronado, R; Alonso, J A; Fernández-Díaz, M T

    2014-06-25

    Sr0.7Ho0.3CoO3-δ oxide has been recently described as an excellent cathode material (1274 mW cm(-2) at 850 °C with pure H2 as fuel1) for solid oxide fuel cells (SOFCs) with LSGM as electrolyte. In this work, we describe a detailed study of its crystal structure conducted to find out the correlation between the excellent performance as a cathode and the structural features. The tetragonal crystal structure (e.g., I4/mmm) basically contains layers of octahedrally coordinated Co2O6 units alternated with layers of Co1O4 tetrahedra sharing corners. An "in situ" neutron power diffraction (NPD) experiment, between 25 and 800 °C, reveals the presence of a high oxygen deficiency affecting O4 oxygen atoms, with large displacement factors that suggest a large lability and mobility. Difference Fourier maps allow the visualization at high temperatures of the 2D diffusion pathways within the tetrahedral layers, where O3 and O4 oxygens participate. The measured thermal expansion coefficient is 16.61 × 10(-6) K(-1) between 300 and 850 °C, exhibiting an excellent chemical compatibility with the electrolyte. PMID:24873238

  14. Tungsten oxide buffer layers fabricated in an inert sol-gel process at room-temperature for blue organic light-emitting diodes.

    PubMed

    Höfle, Stefan; Bruns, Michael; Strässle, Stefan; Feldmann, Claus; Lemmer, Uli; Colsmann, Alexander

    2013-08-14

    WO3 deposition from tungsten ethoxide precursor solutions at room temperature is demonstrated. The W(OEt)6 precursor can be converted under inert conditions and hence avoids sample contamination with oxygen, opening a pathway to more stable devices. The stoichiometry of all WO3 layers and the optoelectronic performance of the respective SMOLEDs well match thermally evaporated WO3 and its corresponding SMOLEDs. The solution processed WO3 hole injection layers enable the fabrication of blue phosphorescent OLEDs with low onset voltage and current efficiencies of up to 14 cd A(-1) .

  15. Hydrofluoric-nitric-sulphuric-acid surface treatment of tungsten for carbon fibre-reinforced composite hybrids in space applications

    NASA Astrophysics Data System (ADS)

    Kanerva, M.; Johansson, L.-S.; Campbell, J. M.; Revitzer, H.; Sarlin, E.; Brander, T.; Saarela, O.

    2015-02-01

    Hybrid material systems, such as combinations of tungsten foils and carbon fibre-reinforced plastic (CFRP), are replacing metal alloy concepts in spacecraft enclosures. However, a good adhesion between the tungsten oxide scale and the epoxy resin used is required. Here, the effects of a hydrofluoric-nitric-sulphuric-acid (HFNS) treatment on tungsten oxides and subsequent adhesion to CFRP are analysed using atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and fracture testing. The work shows that HFNS treatment results in decreased oxygen content, over 50% thinner tungsten trioxide (WO3) layer and increased nano-roughness on thin tungsten foils. Fracture testing established a 39% increase in the average critical strain for tungsten-CFRP specimens after HFNS treatment was carried out on tungsten. The effect of the oxide scale modification regarding the critical strain energy release rate was ΔGc≈ 8.4 J/m2.

  16. Tungsten Ditelluride: a layered semimetal

    NASA Astrophysics Data System (ADS)

    Lee, Chia-Hui; Silva, Eduardo Cruz; Calderin, Lazaro; Nguyen, Minh An T.; Hollander, Matthew J.; Bersch, Brian; Mallouk, Thomas E.; Robinson, Joshua A.

    2015-06-01

    Tungsten ditelluride (WTe2) is a transition metal dichalcogenide (TMD) with physical and electronic properties that make it attractive for a variety of electronic applications. Although WTe2 has been studied for decades, its structure and electronic properties have only recently been correctly described. We experimentally and theoretically investigate the structure, dynamics and electronic properties of WTe2, and verify that WTe2 has its minimum energy configuration in a distorted 1T structure (Td structure), which results in metallic-like transport. Our findings unambiguously confirm the metallic nature of WTe2, introduce new information about the Raman modes of Td-WTe2, and demonstrate that Td-WTe2 is readily oxidized via environmental exposure. Finally, these findings confirm that, in its thermodynamically favored Td form, the utilization of WTe2 in electronic device architectures such as field effect transistors may need to be reevaluated.

  17. Tungsten diffusion in olivine

    NASA Astrophysics Data System (ADS)

    Cherniak, D. J.; Van Orman, J. A.

    2014-03-01

    Diffusion of tungsten has been characterized in synthetic forsterite and natural olivine (Fo90) under dry conditions. The source of diffusant was a mixture of magnesium tungstate and olivine powders. Experiments were prepared by sealing the source material and polished olivine under vacuum in silica glass ampoules with solid buffers to buffer at NNO or IW. Prepared capsules were annealed in 1 atm furnaces for times ranging from 45 min to several weeks, at temperatures from 1050 to 1450 °C. Tungsten distributions in the olivine were profiled by Rutherford Backscattering Spectrometry (RBS). The following Arrhenius relation is obtained for W diffusion in forsterite: D=1.0×10-8exp(-365±28 kJ mol/RT) m s Diffusivities for the synthetic forsterite and natural Fe-bearing olivine are similar, and tungsten diffusion in olivine shows little dependence on crystallographic orientation or oxygen fugacity. The slow diffusivities measured for W in olivine indicate that Hf-W ages in olivine-metal systems will close to diffusive exchange at higher temperatures than other chronometers commonly used in cosmochronology, and that tungsten isotopic signatures will be less likely to be reset by subsequent thermal events.

  18. High purity tungsten targets

    NASA Technical Reports Server (NTRS)

    1975-01-01

    High purity tungsten, which is used for targets in X-ray tubes was considered for space processing. The demand for X-ray tubes was calculated using the growth rates for dental and medical X-ray machines. It is concluded that the cost benefits are uncertain.

  19. Gas tungsten arc welder

    DOEpatents

    Christiansen, D.W.; Brown, W.F.

    A welder for automated closure of fuel pins by a gas tungsten arc process in which a rotating length of cladding is positioned adjacent a welding electrode in a sealed enclosure. An independently movable axial grinder is provided in the enclosure for refurbishing the used electrode between welds.

  20. Ultrafast 2D IR microscopy

    PubMed Central

    Baiz, Carlos R.; Schach, Denise; Tokmakoff, Andrei

    2014-01-01

    We describe a microscope for measuring two-dimensional infrared (2D IR) spectra of heterogeneous samples with μm-scale spatial resolution, sub-picosecond time resolution, and the molecular structure information of 2D IR, enabling the measurement of vibrational dynamics through correlations in frequency, time, and space. The setup is based on a fully collinear “one beam” geometry in which all pulses propagate along the same optics. Polarization, chopping, and phase cycling are used to isolate the 2D IR signals of interest. In addition, we demonstrate the use of vibrational lifetime as a contrast agent for imaging microscopic variations in molecular environments. PMID:25089490

  1. AnisWave 2D

    2004-08-01

    AnisWave2D is a 2D finite-difference code for a simulating seismic wave propagation in fully anisotropic materials. The code is implemented to run in parallel over multiple processors and is fully portable. A mesh refinement algorithm has been utilized to allow the grid-spacing to be tailored to the velocity model, avoiding the over-sampling of high-velocity materials that usually occurs in fixed-grid schemes.

  2. Proteomic analysis of human bladder epithelial cells by 2D blue native SDS-PAGE reveals TCDD-induced alterations of calcium and iron homeostasis possibly mediated by nitric oxide.

    PubMed

    Verma, Nisha; Pink, Mario; Petrat, Frank; Rettenmeier, Albert W; Schmitz-Spanke, Simone

    2015-01-01

    A proteomic analysis of the interaction among multiprotein complexes involved in 2,3,7,8-dibenzo-p-dioxin (TCDD)-mediated toxicity in urinary bladder epithelial RT4 cells was performed using two-dimensional blue native SDS-PAGE (2D BN/SDS-PAGE). To enrich the protein complexes, unexposed and TCDD-exposed cells were fractionated. BN/SDS-PAGE of the resulting fractions led to an effective separation of proteins and protein complexes of various origins, including cell membrane, mitochondria, and other intracellular compartments. Major differences between the proteome of control and exposed cells involved the alteration of many calcium-regulated proteins (calmodulin, protein S100-A2, annexin A5, annexin A10, gelsolin isoform b) and iron-regulated proteins (ferritin, heme-binding protein 2, transferrin). On the basis of these findings, the intracellular calcium concentration was determined, revealing a significant increase after 24 h of exposure to TCDD. Moreover, the concentration of the labile iron pool (LIP) was also significantly elevated in TCDD-exposed cells. This increase was strongly inhibited by the calmodulin (CaM) antagonist W-7, which pointed toward a possible interaction between iron and calcium signaling. Because nitric oxide (NO) production was significantly enhanced in TCDD-exposed cells and was also inhibited by W-7, we hypothesize that alterations in calcium and iron homeostasis upon exposure to TCDD may be linked through NO generated by CaM-activated nitric oxide synthase. In our model, we propose that NO produced upon TCDD exposure interacts with the iron centers of iron-regulatory proteins (IRPs) that modulate the alteration of ferritin and transferrin, resulting in an augmented cellular LIP and, hence, increased toxicity.

  3. Characterization of the impurities in tungsten/silicon-germanium contacts

    SciTech Connect

    Gregg, H.A. Sr.

    1986-03-26

    Secondary ion mass spectrometry and Auger electron spectrometry depth profiling were used to determine impurity distributions in sputter deposited tungsten films over N-type and P-type 80/20 silicon-germanium elements of thermoelectric devices. These analyses showed that silicon, oxygen, sodium, boron, and phosphorous were present as impurities in the tungsten film. All these impurities except oxygen and sodium came from the substrate. Oxygen was gettered by the tungsten films, while sodium was possibly the result of sample handling. Further, the results from this study indicate that an oxide build-up, primarily at the tungsten/silicon-germanium interface of the N-type materials, is the major contributor to contact resistance in thermoelectric devices.

  4. Surface studies of thermionic cathodes and the mechanism of operation of an impregnated tungsten cathode

    NASA Technical Reports Server (NTRS)

    Forman, R.

    1976-01-01

    The surface properties of conventional impregnated cathodes were investigated by the use of Auger spectroscopy and work function measurements, and these were compared with a synthesized barium or barium oxide coated tungsten surface. The barium and barium oxide coated surfaces were prepared by evaporating barium onto a tungsten surface that can be heated to elevated temperatures. Multilayer or monolayer coverages can be investigated using this technique. The results of this study show that the surface of an impregnated tungsten cathode is identical to that observed for a synthesized monolayer or partial monolayer of barium on partially oxidized tungsten, using the criteria of identical Auger patterns and work functions. Desorption measurements of barium from a tungsten surface were also made. These results in conjunction with Auger and work function data were interpreted to show that throughout most of its life an impregnated cathode operating in the range of 1100 C has a partial monolayer rather than a monolayer of barium on its surface.

  5. Bend ductility of tungsten heavy alloys

    SciTech Connect

    Gurwell, W.E.; Garnich, M.R.; Dudder, G.B.; Lavender, C.A.

    1992-11-01

    A bend ductility test is used to indicate the formability of tungsten heavy alloys sheet. The primary test bends a notchless Charpy impact specimen to a bend angle of approximately 100C. This can be augmented by a bend-completion test. Finite element modeling as well as strain-gaged bend specimens elucidate the strain distribution in the specimen as a function of material thickness and bend angle. The bend ductilities of 70%W, 807.W and 90%W alloys are characterized. As expected, decreasing thickness or tungsten content enhances bend ductility. Oxidation is not detrimental; therefore, controlled atmosphere is not required for cooling. The potentially detrimental effects of mechanical working (e.g., rolling, roller-leveling, grit blasting, and peening) and machining (e.g., cutting and sanding) are illustrated.

  6. Helium bubble bursting in tungsten

    SciTech Connect

    Sefta, Faiza; Juslin, Niklas; Wirth, Brian D.

    2013-12-28

    Molecular dynamics simulations have been used to systematically study the pressure evolution and bursting behavior of sub-surface helium bubbles and the resulting tungsten surface morphology. This study specifically investigates how bubble shape and size, temperature, tungsten surface orientation, and ligament thickness above the bubble influence bubble stability and surface evolution. The tungsten surface is roughened by a combination of adatom “islands,” craters, and pinholes. The present study provides insight into the mechanisms and conditions leading to various tungsten topology changes, which we believe are the initial stages of surface evolution leading to the formation of nanoscale fuzz.

  7. Aerosol-Assisted CVD-Grown PdO Nanoparticle-Decorated Tungsten Oxide Nanoneedles Extremely Sensitive and Selective to Hydrogen.

    PubMed

    Annanouch, Fatima E; Haddi, Z; Ling, M; Di Maggio, F; Vallejos, S; Vilic, T; Zhu, Y; Shujah, T; Umek, P; Bittencourt, C; Blackman, C; Llobet, E

    2016-04-27

    We report for the first time the successful synthesis of palladium (Pd) nanoparticle (NP)-decorated tungsten trioxide (WO3) nanoneedles (NNs) via a two-step aerosol-assisted chemical vapor deposition approach. Morphological, structural, and elemental composition analysis revealed that a Pd(acac)2 precursor was very suitable to decorate WO3 NNs with uniform and well-dispersed PdO NPs. Gas-sensing results revealed that decoration with PdO NPs led to an ultrasensitive and selective hydrogen (H2) gas sensor (sensor response peaks at 1670 at 500 ppm of H2) with low operating temperature (150 °C). The response of decorated NNs is 755 times higher than that of bare WO3 NNs. Additionally, at a temperature near that of the ambient temperature (50 °C), the response of this sensor toward the same concentration of H2 was 23, which is higher than that of some promising sensors reported in the literature. Finally, humidity measurements showed that PdO/WO3 sensors displayed low-cross-sensitivity toward water vapor, compared to bare WO3 sensors. The addition of PdO NPs helps to minimize the effect of ambient humidity on the sensor response. PMID:27043301

  8. Effect of ingested tungsten oxide (WOx) nanofibers on digestive gland tissue of Porcellio scaber (Isopoda, Crustacea): fourier transform infrared (FTIR) imaging.

    PubMed

    Novak, Sara; Drobne, Damjana; Vaccari, Lisa; Kiskinova, Maya; Ferraris, Paolo; Birarda, Giovanni; Remškar, Maja; Hočevar, Matej

    2013-10-01

    Tungsten nanofibers are recognized as biologically potent. We study deviations in molecular composition between normal and digestive gland tissue of WOx nanofibers (nano-WOx) fed invertebrate Porcellio scaber (Iosopda, Crustacea) and revealed mechanisms of nano-WOx effect in vivo. Fourier Transform Infrared (FTIR) imaging performed on digestive gland epithelium was supplemented by toxicity and cytotoxicity analyses as well as scanning electron microscopy (SEM) of the surface of the epithelium. The difference in the spectra of the Nano-WOx treated and control cells showed up in the central region of the cells and were related to lipid peroxidation, and structural changes of nucleic acids. The conventional toxicity parameters failed to show toxic effects of nano-WOx, whereas the cytotoxicity biomarkers and SEM investigation of digestive gland epithelium indicated sporadic effects of nanofibers. Since toxicological and cytological measurements did not highlight severe effects, the biochemical alterations evidenced by FTIR imaging have been explained as the result of cell protection (acclimation) mechanisms to unfavorable conditions and indication of a nonhomeostatic state, which can lead to toxic effects.

  9. Mineral resource of the month: tungsten

    USGS Publications Warehouse

    Shedd, Kim B.

    2012-01-01

    The article offers information on tungsten. It says that tungsten is a metal found in chemical compounds such as in the scheelite and ore minerals wolframite. It states that tungsten has the highest melting point and it forms a compound as hard as diamond when combined with carbon. It states that tungsten can be used as a substitute for lead in fishing weights, ammunition, and hunting shot. Moreover, China started to export tungsten materials and products instead of tungsten raw materials.

  10. Interaction of tungsten with tungsten carbide in a copper melt

    NASA Astrophysics Data System (ADS)

    Bodrova, L. E.; Goida, E. Yu.; Pastukhov, E. A.; Marshuk, L. A.; Popova, E. A.

    2013-07-01

    The chemical interaction between tungsten and tungsten carbide in a copper melt with the formation of W2C at 1300°C is studied. It is shown that the mechanical activation of a composition consisting of copper melt + W and WC powders by low-temperature vibrations initiates not only the chemical interaction of its solid components but also their refinement.

  11. DYNA2D96. Explicit 2-D Hydrodynamic FEM Program

    SciTech Connect

    Whirley, R.G.

    1992-04-01

    DYNA2D is a vectorized, explicit, two-dimensional, axisymmetric and plane strain finite element program for analyzing the large deformation dynamic and hydrodynamic response of inelastic solids. DYNA2D contains 13 material models and 9 equations of state (EOS) to cover a wide range of material behavior. The material models implemented in all machine versions are: elastic, orthotropic elastic, kinematic/isotropic elastic plasticity, thermoelastoplastic, soil and crushable foam, linear viscoelastic, rubber, high explosive burn, isotropic elastic-plastic, temperature-dependent elastic-plastic. The isotropic and temperature-dependent elastic-plastic models determine only the deviatoric stresses. Pressure is determined by one of 9 equations of state including linear polynomial, JWL high explosive, Sack Tuesday high explosive, Gruneisen, ratio of polynomials, linear polynomial with energy deposition, ignition and growth of reaction in HE, tabulated compaction, and tabulated.

  12. VAPORIZATION OF TUNGSTEN-METAL IN STEAM AT HIGH TEMPERATURES.

    SciTech Connect

    GREENE,G.A.; FINFROCK,C.C.

    2000-10-01

    The vaporization of tungsten from the APT spallation target dominates the radiological source term for unmitigated target overheating accidents. Chemical reactions of tungsten with steam which persist to tungsten temperatures as low as 800 C result in the formation of a hydrated tungsten-oxide which has a high vapor pressure and is readily convected in a flowing atmosphere. This low-temperature vaporization reaction essentially removes the oxide film that forms on the tungsten-metal surface as soon as it forms, leaving behind a fresh metallic surface for continued oxidation and vaporization. Experiments were conducted to measure the oxidative vaporization rates of tungsten in steam as part of the effort to quantify the MT radiological source term for severe target accidents. Tests were conducted with tungsten rods (1/8 inch diameter, six inches long) heated to temperatures from approximately 700 C to 1350 C in flowing steam which was superheated to 140 C. A total of 19 experiments was conducted. Fifteen tests were conducted by RF induction heating of single tungsten rods held vertical in a quartz glass retort. Four tests were conducted in a vertically-mounted tube furnace for the low temperature range of the test series. The aerosol which was generated and transported downstream from the tungsten rods was collected by passing the discharged steam through a condenser. This procedure insured total collection of the steam along with the aerosol from the vaporization of the rods. The results of these experiments revealed a threshold temperature for tungsten vaporization in steam. For the two tests at the lowest temperatures which were tested, approximately 700 C, the tungsten rods were observed to oxidize without vaporization. The remainder of the tests was conducted over the temperature range of 800 C to 1350 C. In these tests, the rods were found to have lost weight due to vaporization of the tungsten and the missing weight was collected in the downstream condensate

  13. TUNGSTEN BASE ALLOYS

    DOEpatents

    Schell, D.H.; Sheinberg, H.

    1959-12-15

    A high-density quaternary tungsten-base alloy having high mechanical strength and good machinability composed of about 2 wt.% Ni, 3 wt.% Cu, 5 wt.% Pb, and 90wt.% W is described. This alloy can be formed by the powder metallurgy technique of hot pressing in a graphite die without causing a reaction between charge and the die and without formation of a carbide case on the final compact, thereby enabling re-use of the graphite die. The alloy is formable at hot- pressing temperatures of from about 1200 to about 1350 deg C. In addition, there is little component shrinkage, thereby eliminating the necessity of subsequent extensive surface machining.

  14. MOSS2D V1

    2001-01-31

    This software reduces the data from two-dimensional kSA MOS program, k-Space Associates, Ann Arbor, MI. Initial MOS data is recorded without headers in 38 columns, with one row of data per acquisition per lase beam tracked. The final MOSS 2d data file is reduced, graphed, and saved in a tab-delimited column format with headers that can be plotted in any graphing software.

  15. The oxidation behavior of a model molybdenum/tungsten-containing alloy in air alone and in air with trace levels of NaCl(g)

    NASA Technical Reports Server (NTRS)

    Smeggil, J. G.; Bornstein, N. S.

    1983-01-01

    Thermogravimetric, metallographic, and X-ray studies of a model alloy, Ni-(17 a/o)Al-(10 a/o)Mo+W, oxidized in dry air at 600-1200 C and in air with 10 ppm NaCl gas at 900 C, are reported. The alloy was melted under Ar and pretreated in flowing H2 for 24 h at 1300 C. Polished 1.3 x 1.3 x 0.2-cm specimens were washed and degreased prior to oxidation in a quartz tube within a furnace for up to 120 hr. The oxidation activation energy of the alloy is determined to be about 30 kcal/mole. The specimens oxidized at 900 C and hotter exhibited oxidized and nitrided phases covered by complex NiMoO4, NiWO4, and NiAl2O4 scales and a porous, nonprotective outer layer of NiO. The oxidation behavior is found to be determined by the formation and growth of the scale, especially the (Mo,W)O2 component. Al2O3 scale layers were not formed, and further runs with pure O2 or Ar-(20 percent)O2 ruled out an explanation of this phenomenon based on aluminum nitride formation. The oxidation was accelerated by the addition of NaCl gas, a finding attributed to the reaction of NaCl with external locally protective Al2O3 scales and with the internal(Mo, W)O2 layers.

  16. Internal Wire Guide For Gas/Tungsten-Arc Welding

    NASA Technical Reports Server (NTRS)

    Morgan, Gene E.; Dyer, Gerald E.

    1990-01-01

    Wire kept in shielding gas, preventing oxidation. Guide inside gas cup of gas/tungsten-arc welding torch feeds filler wire to weld pool along line parallel to axis of torch. Eliminates problem of how to place and orient torch to provide clearance for external wire guide.

  17. Xenon-Ion Drilling of Tungsten Films

    NASA Technical Reports Server (NTRS)

    Garner, C. E.

    1986-01-01

    High-velocity xenon ions used to drill holes of controlled size and distribution through tungsten layer that sheaths surface of controlled-porosity dispenser cathode of traveling wave-tube electron emitter. Controlled-porosity dispenser cathode employs barium/calcium/ aluminum oxide mixture that migrates through pores in cathode surface, thus coating it and reducing its work function. Rapid, precise drilling technique applied to films of other metals and used in other applications where micron-scale holes required. Method requires only few hours, as opposed to tens of hours by prior methods.

  18. 49 CFR 173.338 - Tungsten hexafluoride.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Tungsten hexafluoride. 173.338 Section 173.338... SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.338 Tungsten hexafluoride. (a) Tungsten... expansion test, must be condemned if removed from tungsten hexafluoride service....

  19. 49 CFR 173.338 - Tungsten hexafluoride.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Tungsten hexafluoride. 173.338 Section 173.338... SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.338 Tungsten hexafluoride. (a) Tungsten... expansion test, must be condemned if removed from tungsten hexafluoride service....

  20. 49 CFR 173.338 - Tungsten hexafluoride.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Tungsten hexafluoride. 173.338 Section 173.338... SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.338 Tungsten hexafluoride. (a) Tungsten... expansion test, must be condemned if removed from tungsten hexafluoride service....

  1. 49 CFR 173.338 - Tungsten hexafluoride.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Tungsten hexafluoride. 173.338 Section 173.338... SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.338 Tungsten hexafluoride. (a) Tungsten... expansion test, must be condemned if removed from tungsten hexafluoride service....

  2. 49 CFR 173.338 - Tungsten hexafluoride.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Tungsten hexafluoride. 173.338 Section 173.338... SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.338 Tungsten hexafluoride. (a) Tungsten... expansion test, must be condemned if removed from tungsten hexafluoride service....

  3. High strength uranium-tungsten alloy process

    DOEpatents

    Dunn, Paul S.; Sheinberg, Haskell; Hogan, Billy M.; Lewis, Homer D.; Dickinson, James M.

    1990-01-01

    Alloys of uranium and tungsten and a method for making the alloys. The amount of tungsten present in the alloys is from about 4 wt % to about 35 wt %. Tungsten particles are dispersed throughout the uranium and a small amount of tungsten is dissolved in the uranium.

  4. High strength uranium-tungsten alloys

    DOEpatents

    Dunn, Paul S.; Sheinberg, Haskell; Hogan, Billy M.; Lewis, Homer D.; Dickinson, James M.

    1991-01-01

    Alloys of uranium and tungsten and a method for making the alloys. The amount of tungsten present in the alloys is from about 4 wt % to about 35 wt %. Tungsten particles are dispersed throughout the uranium and a small amount of tungsten is dissolved in the uranium.

  5. Broadband THz Spectroscopy of 2D Nanoscale Materials

    NASA Astrophysics Data System (ADS)

    Chen, Lu; Tripathi, Shivendra; Huang, Mengchen; Hsu, Jen-Feng; D'Urso, Brian; Lee, Hyungwoo; Eom, Chang-Beom; Irvin, Patrick; Levy, Jeremy

    Two-dimensional (2D) materials such as graphene and transition-metal dichalcogenides (TMDC) have attracted intense research interest in the past decade. Their unique electronic and optical properties offer the promise of novel optoelectronic applications in the terahertz regime. Recently, generation and detection of broadband terahertz (10 THz bandwidth) emission from 10-nm-scale LaAlO3/SrTiO3 nanostructures created by conductive atomic force microscope (c-AFM) lithography has been demonstrated . This unprecedented control of THz emission at 10 nm length scales creates a pathway toward hybrid THz functionality in 2D-material/LaAlO3/SrTiO3 heterostructures. Here we report initial efforts in THz spectroscopy of 2D nanoscale materials with resolution comparable to the dimensions of the nanowire (10 nm). Systems under investigation include graphene, single-layer molybdenum disulfide (MoS2), and tungsten diselenide (WSe2) nanoflakes. 1. Y. Ma, et al., Nano Lett. 13, 2884 (2013). We gratefully acknowledge financial support from the following agencies and grants: AFOSR (FA9550-12-1-0268 (JL, PRI), FA9550-12-1-0342 (CBE)), ONR (N00014-13-1-0806 (JL, CBE), N00014-15-1-2847 (JL)), NSF DMR-1124131 (JL, CBE) and DMR-1234096 (CBE).

  6. METHOD OF MAKING TUNGSTEN FILAMENTS

    DOEpatents

    Frazer, J.W.

    1962-12-18

    A method of making tungsten filaments is described in which the tungsten is completely free of isotope impurities in the range of masses 234 to 245 for use in mass spectrometers. The filament comprises a tantalum core generally less than 1 mil in diameter having a coating of potassium-free tantalum-diffused tungsten molecularly bonded thereto. In the preferred process of manufacture a short, thin tantalum filament is first mounted between terminal posts mounted in insulated relation through a backing plate. The tungsten is most conveniently vapor plated onto the tantalum by a tungsten carbonyl vapor decomposition method having a critical step because of the tendency of the tantalum to volatilize at the temperature of operntion of the filament. The preferred recipe comprises volatilizing tantalum by resistance henting until the current drops by about 40%, cutting the voltage back to build up the tungsten, and then gradually building the temperature back up to balance the rate of tungsten deposition with the rate of tantalum volatilization. (AEC)

  7. The nitrate reductase inhibitor, tungsten, disrupts actin microfilaments in Zea mays L.

    PubMed

    Adamakis, Ioannis-Dimosthenis S; Panteris, Emmanuel; Eleftheriou, Eleftherios P

    2014-05-01

    Tungsten is a widely used inhibitor of nitrate reductase, applied to diminish the nitric oxide levels in plants. It was recently shown that tungsten also has heavy metal attributes. Since information about the toxic effects of tungsten on actin is limited, and considering that actin microfilaments are involved in the entry of tungsten inside plant cells, the effects of tungsten on them were studied in Zea mays seedlings. Treatments with sodium tungstate for 3, 6, 12 or 24 h were performed on intact seedlings and seedlings with truncated roots. Afterwards, actin microfilaments in meristematic root and leaf tissues were stained with fluorescent phalloidin, and the specimens were examined by confocal laser scanning microscopy. While the actin microfilament network was well organized in untreated seedlings, in tungstate-treated ones it was disrupted in a time-dependent manner. In protodermal root cells, the effects of tungsten were stronger as cortical microfilaments were almost completely depolymerized and the intracellular ones appeared highly bundled. Fluorescence intensity measurements confirmed the above results. In the meristematic leaf tissue of intact seedlings, no depolymerization of actin microfilaments was noticed. However, when root tips were severed prior to tungstate application, both cortical and endoplasmic actin networks of leaf cells were disrupted and bundled after 24 h of treatment. The differential response of root and leaf tissues to tungsten toxicity may be due to differential penetration and absorption, while the effects on actin microfilaments could not be attributed to the nitric oxide depletion by tungsten.

  8. RECOVERY OF URANIUM FROM TUNGSTEN

    DOEpatents

    Newnam, K.

    1959-02-01

    A method is presented for the rccovery of uranium which has adhered to tungsten parts in electromagnetic isotope separation apparatus. Such a tungsten article is dissolved electrolytically in 20% NaOH by using the tungsten article as the anode. The resulting solution, containing soluble sodium lungstate and an insoluble slime, is then filtered. The slime residue is ignited successively with sodium nitrate and sodium pyrosulfate and leashed, and the resulting filtrates are combined with the original filtrate. Uranium is then recovered from the combined flltrates by diuranate precipitation.

  9. Tungsten Toxicity in Plants

    PubMed Central

    Adamakis, Ioannis-Dimosthenis S.; Panteris, Emmanuel; Eleftheriou, Eleftherios P.

    2012-01-01

    Tungsten (W) is a rare heavy metal, widely used in a range of industrial, military and household applications due to its unique physical properties. These activities inevitably have accounted for local W accumulation at high concentrations, raising concerns about its effects for living organisms. In plants, W has primarily been used as an inhibitor of the molybdoenzymes, since it antagonizes molybdenum (Mo) for the Mo-cofactor (MoCo) of these enzymes. However, recent advances indicate that, beyond Mo-enzyme inhibition, W has toxic attributes similar with those of other heavy metals. These include hindering of seedling growth, reduction of root and shoot biomass, ultrastructural malformations of cell components, aberration of cell cycle, disruption of the cytoskeleton and deregulation of gene expression related with programmed cell death (PCD). In this article, the recent available information on W toxicity in plants and plant cells is reviewed, and the knowledge gaps and the most pertinent research directions are outlined. PMID:27137642

  10. Tungsten resources of Brazil

    USGS Publications Warehouse

    White, Max Gregg

    1974-01-01

    Brazilian tungsten production, 85 percent of which is exported, comes almost entirely from scheelite-bearing tactites in northeast Brazil, and has reached an annual rate of about 2,000 metric tons (2,200 short tons) of scheelite concentrate with 70 percent WO3. Scheelite ore reserves, located principally in the State of Rio Grande do Norte, are estimated to be as high as 8,300,000 tons (9,100,000 short tons) containing 0.7 percent WO3. Minor deposits (or those about which only minimal information is available) of wolframite, with which some cassiterite is associated, are located in Sao Paulo, Santa Catarina, and Rio Grande do Sul. Both the scheelite and the wolframite deposits are considered . to be late Precambrian A (620 to 900 m.y.) or early Cambrian in age.

  11. Mechanistic, kinetic, and processing aspects of tungsten chemical mechanical polishing

    NASA Astrophysics Data System (ADS)

    Stein, David

    This dissertation presents an investigation into tungsten chemical mechanical polishing (CMP). CMP is the industrially predominant unit operation that removes excess tungsten after non-selective chemical vapor deposition (CVD) during sub-micron integrated circuit (IC) manufacture. This work explores the CMP process from process engineering and fundamental mechanistic perspectives. The process engineering study optimized an existing CMP process to address issues of polish pad and wafer carrier life. Polish rates, post-CMP metrology of patterned wafers, electrical test data, and synergy with a thermal endpoint technique were used to determine the optimal process. The oxidation rate of tungsten during CMP is significantly lower than the removal rate under identical conditions. Tungsten polished without inhibition during cathodic potentiostatic control. Hertzian indenter model calculations preclude colloids of the size used in tungsten CMP slurries from indenting the tungsten surface. AFM surface topography maps and TEM images of post-CMP tungsten do not show evidence of plow marks or intergranular fracture. Polish rate is dependent on potassium iodate concentration; process temperature is not. The colloid species significantly affects the polish rate and process temperature. Process temperature is not a predictor of polish rate. A process energy balance indicates that the process temperature is predominantly due to shaft work, and that any heat of reaction evolved during the CMP process is negligible. Friction and adhesion between alumina and tungsten were studied using modified AFM techniques. Friction was constant with potassium iodate concentration, but varied with applied pressure. This corroborates the results from the energy balance. Adhesion between the alumina and the tungsten was proportional to the potassium iodate concentration. A heuristic mechanism, which captures the relationship between polish rate, pressure, velocity, and slurry chemistry, is presented

  12. Simulations of tungsten transport in the edge of JET ELMy H-mode plasmas

    NASA Astrophysics Data System (ADS)

    Järvinen, A.; Groth, M.; Moulton, D.; Strachan, J.; Wiesen, S.; Belo, P.; Beurskens, M. N. A.; Corrigan, G.; Eich, T.; Giroud, C.; Havlickova, E.; Jachmich, S.; Lehnen, M.; Lönnroth, J.; Tskhakaya, D.; JET EFDA Contributors

    2013-07-01

    Tungsten contamination can significantly impact the performance of future fusion reactors via fuel dilution and radiation in the plasma centre. Therefore, understanding tungsten sputtering and divertor retention is essential for optimising the core performance in tokamaks operating with tungsten. This study investigates these issues numerically in JET high-triangularity, type-I ELMy H-mode plasmas with the Monte-Carlo code DIVIMP used on background plasmas dynamically evolved with the multi-fluid code EDGE2D/EIRENE. During the ELM, the simulations show target temperatures in excess of a few 100 eV, causing two orders of magnitude increase in the tungsten core contamination rate. During the ELM recovery, target densities of five times the pre-ELM values are obtained at the low field side, which strongly enhance divertor retention via increased friction with the main ions. Therefore, the core contamination is determined here dominantly by the intra-ELM divertor plasma characteristics.

  13. Volatility from copper and tungsten alloys for fusion reactor applications

    SciTech Connect

    Smolik, G.R.; Neilson, R.M. Jr.; Piet, S.J. )

    1989-01-01

    Accident scenarios for fusion power plants present the potential for release and transport of activated constituents volatilized from first wall and structural materials. The extent of possible mobilization and transport of these activated species, many of which are oxidation driven'', is being addressed by the Fusion Safety Program at the Idaho National Engineering Laboratory (INEL). This report presents experimental measurements of volatilization from a copper alloy in air and steam and from a tungsten alloy in air. The major elements released included zinc from the copper alloy and rhenium and tungsten from the tungsten alloy. Volatilization rates of several constituents of these alloys over temperatures ranging from 400 to 1200{degree}C are presented. These values represent release rates recommended for use in accident assessment calculations. 8 refs., 3 figs., 5 tabs.

  14. Tungsten disrupts root growth in Arabidopsis thaliana by PIN targeting.

    PubMed

    Adamakis, Ioannis-Dimosthenis S; Panteris, Emmanuel; Eleftheriou, Eleftherios P

    2014-08-15

    Tungsten is a heavy metal with increasing concern over its environmental impact. In plants it is extensively used to deplete nitric oxide by inhibiting nitrate reductase, but its presumed toxicity as a heavy metal has been less explored. Accordingly, its effects on Arabidopsis thaliana primary root were assessed. The effects on root growth, mitotic cell percentage, nitric oxide and hydrogen peroxide levels, the cytoskeleton, cell ultrastructure, auxin and cytokinin activity, and auxin carrier distribution were investigated. It was found that tungsten reduced root growth, particularly by inhibiting cell expansion in the elongation zone, so that root hairs emerged closer to the root tip than in the control. Although extensive vacuolation was observed, even in meristematic cells, cell organelles were almost unaffected and microtubules were not depolymerized but reoriented. Tungsten affected auxin and cytokinin activity, as visualized by the DR5-GFP and TCS-GFP expressing lines, respectively. Cytokinin fluctuations were similar to those of the mitotic cell percentage. DR5-GFP signal appeared ectopically expressed, while the signals of PIN2-GFP and PIN3-GFP were diminished even after relatively short exposures. The observed effects were not reminiscent of those of any nitric oxide scavengers. Taken together, inhibition of root growth by tungsten might rather be related to a presumed interference with the basipetal flow of auxin, specifically affecting cell expansion in the elongation zone.

  15. Why Tungsten Instead of Wolfram?

    NASA Astrophysics Data System (ADS)

    Jensen, William B.

    2008-04-01

    In response to a reader query, the column traces the reason that American and British chemical literature use the name tungsten for element 74, while northern European literature uses the name wolfram.

  16. Heated die facilitates tungsten forming

    NASA Technical Reports Server (NTRS)

    Chattin, J. H.; Haystrick, J. E.; Laughlin, J. C.; Leidy, R. A.

    1966-01-01

    Tungsten forming in a press brake employs a bottom die assembly with a heating manifold between two water-cooled die sections. The manifold has hydrogen-oxygen burners spaced along its length for even heat during forming.

  17. Unparticle example in 2D.

    PubMed

    Georgi, Howard; Kats, Yevgeny

    2008-09-26

    We discuss what can be learned about unparticle physics by studying simple quantum field theories in one space and one time dimension. We argue that the exactly soluble 2D theory of a massless fermion coupled to a massive vector boson, the Sommerfield model, is an interesting analog of a Banks-Zaks model, approaching a free theory at high energies and a scale-invariant theory with nontrivial anomalous dimensions at low energies. We construct a toy standard model coupling to the fermions in the Sommerfield model and study how the transition from unparticle behavior at low energies to free particle behavior at high energies manifests itself in interactions with the toy standard model particles.

  18. Polarographic determination of tungsten in rocks

    USGS Publications Warehouse

    Reichen, L.E.

    1954-01-01

    This work was undertaken to develop a simpler and faster method than the classical gravimetric procedure for the determination of tungsten in rocks and ores. A new polarographic wave of tungsten is obtained in a supporting electrolyte of dilute hydrochloric acid containing tartrate ion. This permits the determination of tungsten both rapidly and accurately. No precipitation of the tungsten is necessary, and only the iron need be separated from the tungsten. The accuracy is within the limits of a polarographic procedure; comparison of polarographic and gravimetric results is given. The method reduces appreciably the amount of time ordinarily consumed in determination of tungsten.

  19. Process Of Bonding Copper And Tungsten

    DOEpatents

    Slattery, Kevin T.; Driemeyer, Daniel E.; Davis, John W.

    2000-07-18

    Process for bonding a copper substrate to a tungsten substrate by providing a thin metallic adhesion promoting film bonded to a tungsten substrate and a functionally graded material (FGM) interlayer bonding the thin metallic adhesion promoting film to the copper substrate. The FGM interlayer is formed by sintering a stack of individual copper and tungsten powder blend layers having progressively higher copper content/tungsten content, by volume, ratio values in successive powder blend layers in a lineal direction extending from the tungsten substrate towards the copper substrate. The resulting copper to tungsten joint well accommodates the difference in the coefficient of thermal expansion of the materials.

  20. Simple preparation of tungsten supported carbon nanoreactors for specific applications: Adsorption, catalysis and electrochemical activity

    NASA Astrophysics Data System (ADS)

    Mayani, Vishal J.; Mayani, Suranjana V.; Kim, Sang Wook

    2015-08-01

    Porous carbon supported tungsten carbide nanoreactors, two sizes (∼25 and 170 nm), were designed using economical petroleum pitch residue followed by tungsten (W) doping. X-ray diffractions showed both carbon tungsten composites (CTC-25 and CTC-170) contained tungsten subcarbide (W2C) and monocarbide (WC) as the major and minor crystalline phases, respectively. The present study provides a multiple perspective of carbon tungsten composites (CTCs) for methanol oxidation (as an electrode), adsorption (as an adsorbent) and degradation (as a solid catalyst) of methylene blue (MB). The operational electrodes were designed from both CTCs and used as a catalyst in an electrocatalysis process. The electrocatalysts exhibited high and stable catalytic performance (CTCE-25 > CTCE-170) in methanol electro-oxidation. The newly synthesized W-doped carbon nanoreactors were used successfully as an adsorbent for MB and a heterogeneous catalyst for MB oxidation. Ordered CTC-25 and CTC-170 exhibited dynamic MB adsorption within 15 min and complete oxidation of MB in 25-40 min. A synergetic effect between tungsten carbide and the carbon cage framework was noted.

  1. The effect of phosphorus on the formation of tungsten dioxide: A novel morphology

    SciTech Connect

    Hegedus, E.; Neugebauer, J.

    1999-02-19

    The industrial production of tungsten is based on the hydrogen reduction of tungsten oxides, ammonium paratungstate (APT) or ammonium tungsten oxide bronze (ATOB). Hydrogen reduction is applied when high purity tungsten is required and when the addition of other elements or compounds (dopants) is desired for modification of the properties of the metal powder. The first stage of the reduction is finished when WO{sub 2} is formed and it seems that the efficient incorporation of the additives starts mainly at this reduction step. The study reported here was undertaken to investigate the effect of phosphorus dope on the morphology of the intermediate tungsten dioxide and analyze its influence on the grain size of the final tungsten metal powder. The authors observed star shaped morphology of WO{sub 2}, a structure which has not been describe in the literature. Contrary to the well-known cauliflower shaped tungsten dioxide, these starlets are not pseudomorphic to the initial ATOB particles; they grow separately and have a great influence on the grain size of the final metal powder.

  2. Tungsten - Yttrium Based Nuclear Structural Materials

    NASA Astrophysics Data System (ADS)

    Ramana, Chintalapalle; Chessa, Jack; Martinenz, Gustavo

    2013-04-01

    The challenging problem currently facing the nuclear science community in this 21st century is design and development of novel structural materials, which will have an impact on the next-generation nuclear reactors. The materials available at present include reduced activation ferritic/martensitic steels, dispersion strengthened reduced activation ferritic steels, and vanadium- or tungsten-based alloys. These materials exhibit one or more specific problems, which are either intrinsic or caused by reactors. This work is focussed towards tungsten-yttrium (W-Y) based alloys and oxide ceramics, which can be utilized in nuclear applications. The goal is to derive a fundamental scientific understanding of W-Y-based materials. In collaboration with University of Califonia -- Davis, the project is designated to demonstrate the W-Y based alloys, ceramics and composites with enhanced physical, mechanical, thermo-chemical properties and higher radiation resistance. Efforts are focussed on understanding the microstructure, manipulating materials behavior under charged-particle and neutron irradiation, and create a knowledge database of defects, elemental diffusion/segregation, and defect trapping along grain boundaries and interfaces. Preliminary results will be discussed.

  3. Evaluation of 2D ceramic matrix composites in aeroconvective environments

    NASA Technical Reports Server (NTRS)

    Riccitiello, Salvatore R.; Love, Wendell L.; Balter-Peterson, Aliza

    1992-01-01

    An evaluation is conducted of a novel ceramic-matrix composite (CMC) material system for use in the aeroconvective-heating environments encountered by the nose caps and wing leading edges of such aerospace vehicles as the Space Shuttle, during orbit-insertion and reentry from LEO. These CMCs are composed of an SiC matrix that is reinforced with Nicalon, Nextel, or carbon refractory fibers in a 2D architecture. The test program conducted for the 2D CMCs gave attention to their subsurface oxidation.

  4. Accurate pointing of tungsten welding electrodes

    NASA Technical Reports Server (NTRS)

    Ziegelmeier, P.

    1971-01-01

    Thoriated-tungsten is pointed accurately and quickly by using sodium nitrite. Point produced is smooth and no effort is necessary to hold the tungsten rod concentric. The chemically produced point can be used several times longer than ground points. This method reduces time and cost of preparing tungsten electrodes.

  5. Method of synthesizing tungsten nanoparticles

    DOEpatents

    Thoma, Steven G; Anderson, Travis M

    2013-02-12

    A method to synthesize tungsten nanoparticles has been developed that enables synthesis of nanometer-scale, monodisperse particles that can be stabilized only by tetrahydrofuran. The method can be used at room temperature, is scalable, and the product concentrated by standard means. Since no additives or stabilizing surfactants are required, this method is particularly well suited for producing tungsten nanoparticles for dispersion in polymers. If complete dispersion is achieved due to the size of the nanoparticles, then the optical properties of the polymer can be largely maintained.

  6. Tungsten silicide formation from sequentially sputtered tungsten and silicon films

    NASA Astrophysics Data System (ADS)

    Molarius, J. M.; Franssila, S.; Drozdy, G.; Saarilahti, J.

    1991-11-01

    As-deposited tungsten silicide films have typically high resistivity and require annealing to lower the resistivity to practical values. Rapid thermal annealing (RTA) has emerged as the main method because impurity diffusion in silicides is extremely fast. In this study we have explored the possibility of reducing the required thermal budget for tungsten silicide annealing by sputtering multilayer W /Si films. In addition to direct technological relevance, multilayer structures offer new insights into silicide formation. We propose a hypothesis "oxygen supply to interface ratio" for explaining why multilayer W /Si structures are beneficial for silicide formation. We have prevented the possible oxygen barrier formation at the W /Si interface by diminishing the oxygen supply by several means: substrate heating during deposition, multiple thin layers, a silicon capping layer and argon purging during RTA. Tetragonal WSi 2 is formed at 700°C and no silicon-rich phases are observed. Low-resistivity WSi 2 is produced by RTA at 1000°C, 120 s. Sheet resistance values around 3 ω/□ amends the use of tungsten silicide in practical polycide structures. The ultimate resistivity of our WSi 2, 30 μω · cm, is among the lowest reported for tungsten silicide, and it is achieved in a very straightforward fashion, using typical production equipment.

  7. Phase Engineering of 2D Tin Sulfides.

    PubMed

    Mutlu, Zafer; Wu, Ryan J; Wickramaratne, Darshana; Shahrezaei, Sina; Liu, Chueh; Temiz, Selcuk; Patalano, Andrew; Ozkan, Mihrimah; Lake, Roger K; Mkhoyan, K A; Ozkan, Cengiz S

    2016-06-01

    Tin sulfides can exist in a variety of phases and polytypes due to the different oxidation states of Sn. A subset of these phases and polytypes take the form of layered 2D structures that give rise to a wide host of electronic and optical properties. Hence, achieving control over the phase, polytype, and thickness of tin sulfides is necessary to utilize this wide range of properties exhibited by the compound. This study reports on phase-selective growth of both hexagonal tin (IV) sulfide SnS2 and orthorhombic tin (II) sulfide SnS crystals with diameters of over tens of microns on SiO2 substrates through atmospheric pressure vapor-phase method in a conventional horizontal quartz tube furnace with SnO2 and S powders as the source materials. Detailed characterization of each phase of tin sulfide crystals is performed using various microscopy and spectroscopy methods, and the results are corroborated by ab initio density functional theory calculations. PMID:27099950

  8. Phase Engineering of 2D Tin Sulfides.

    PubMed

    Mutlu, Zafer; Wu, Ryan J; Wickramaratne, Darshana; Shahrezaei, Sina; Liu, Chueh; Temiz, Selcuk; Patalano, Andrew; Ozkan, Mihrimah; Lake, Roger K; Mkhoyan, K A; Ozkan, Cengiz S

    2016-06-01

    Tin sulfides can exist in a variety of phases and polytypes due to the different oxidation states of Sn. A subset of these phases and polytypes take the form of layered 2D structures that give rise to a wide host of electronic and optical properties. Hence, achieving control over the phase, polytype, and thickness of tin sulfides is necessary to utilize this wide range of properties exhibited by the compound. This study reports on phase-selective growth of both hexagonal tin (IV) sulfide SnS2 and orthorhombic tin (II) sulfide SnS crystals with diameters of over tens of microns on SiO2 substrates through atmospheric pressure vapor-phase method in a conventional horizontal quartz tube furnace with SnO2 and S powders as the source materials. Detailed characterization of each phase of tin sulfide crystals is performed using various microscopy and spectroscopy methods, and the results are corroborated by ab initio density functional theory calculations.

  9. Fabrication of tungsten wire needles

    SciTech Connect

    Roder, A.

    1983-02-01

    Fine point needles for field emissoin are conventionally produced by electrolytically or chemically etching tungsten wire. Points formed in this manner have a typical tip radius of about 0.5 microns and a cone angle of some 30 degrees. The construction of needle matrix detector chambers has created a need for tungsten needles whose specifications are: 20 mil tungsten wire, 1.5 inch total length, 3 mm-long taper (resulting in a cone angle of about 5 degrees), and 25 micron-radius point (similar to that found on sewing needles). In the process described here for producing such needles, tungsten wire, immersed in a NaOH solution and in the presence of an electrode, is connected first to an ac voltage and then to a dc supply, to form a taper and a point on the end of the wire immersed in the solution. The process parameters described here are for needles that will meet the above specifications. Possible variations will be discussed under each approprite heading.

  10. Mineral of the month: tungsten

    USGS Publications Warehouse

    Shedd, Kim B.

    2006-01-01

    Tungsten has the highest melting point of all metals, one of the highest densities and, when combined with carbon, is almost as hard as diamond. These and other properties make it useful in a wide variety of important commercial, industrial and military applications.

  11. Vacuum Gas Tungsten Arc Welding

    NASA Technical Reports Server (NTRS)

    Weeks, J. L.; Todd, D. T.; Wooten, J. R.

    1997-01-01

    A two-year program investigated vacuum gas tungsten arc welding (VGTAW) as a method to modify or improve the weldability of normally difficult-to-weld materials. After a vacuum chamber and GTAW power supply were modified, several difficult-to-weld materials were studied and key parameters developed. Finally, Incoloy 903 weld overlays were produced without microfissures.

  12. Tungsten Stable Isotope Compositions of Ferromanganese Crusts

    NASA Astrophysics Data System (ADS)

    Abraham, K.; Barling, J.; Hein, J. R.; Schauble, E. A.; Halliday, A. N.

    2014-12-01

    We report the first accurate and precise data for mass-dependent fractionation of tungsten (W) stable isotopes, using a double spike technique and MC-ICPMS. Results are expressed relative to the NIST 3136 W isotope standard as per mil deviations in 186W/184W (δ186W). Although heavy element mass-dependent fractionations are expected to be small, Tl and U both display significant low temperature isotopic fractionations. Theoretical calculations indicate that W nuclear volume isotopic effects should be smaller than mass-dependent fractionations at low temperatures. Hydrogenetic ferromanganese (Fe-Mn) crusts precipitate directly from seawater and have been used as paleoceanographic recorders of temporal changes in seawater chemistry. Crusts are strongly enriched in W and other metals, and are a promising medium for exploring W isotopic variability. Tungsten has a relatively long residence time in seawater of ~61,000 years, mainly as the tungstate ion (WO42-). Water depth profiles show conservative behaviour. During adsorption on Fe-Mn crusts, W species form inner-sphere complexes in the hexavalent (W6+) state. The major host phase is thought to be Mn oxides and the lighter W isotope is expected to be absorbed preferentially. Surface scrapings of 13 globally distributed hydrogenetic Fe-Mn crusts display δ186W from -0.08 to -0.22‰ (±0.03‰, 2sd). A trend toward lighter W isotope composition exists with increasing water depth (~1500 to ~5200m) and W concentration. One hydrothermal Mn-oxide sample is anomalously light and Mn nodules are both heavy and light relative to Fe-Mn crusts. Tungsten speciation depends on concentration, pH, and time in solution and is not well understood because of the extremely slow kinetics of the reactions. In addition, speciation of aqueous and/or adsorbed species might be sensitive to pressure, showing similar thermodynamic stability but different effective volumes. Thus, W stable isotopes might be used as a water-depth barometer in

  13. Process development for cladding APT tungsten targets

    SciTech Connect

    Horner, M H; Barber, R; Dalder, E

    2000-11-27

    This report describes development of processes for cladding APT Target tungsten components with a thin layer (0.127-mm) of Alloy 718, Alloy 600 or 316L stainless steel alloy. The application requires that the cladding be thermally bonded to the tungsten in order to transfer heat generated in the tungsten volume to a surrounding coolant. High temperature diffusion bonding using the hot isostatic processing (HIP) technique was selected as the method for creating a metallurgical bond between pure tungsten tubes and rods and the cladding materials. Bonding studies using a uniaxially loaded vacuum hot press were conducted in preliminary experiments to determine acceptable time-temperature conditions for diffusion bonding. The results were successfully applied in cladding tungsten rods and tubes with these alloys. Temperatures 800-810 C were suitable for cladding tungsten with Alloy 600 and 316L stainless steel alloy, whereas tungsten was clad with Alloy 718 at 1020 C.

  14. Process Of Bonding Copper And Tungsten

    DOEpatents

    Slattery, Kevin T.; Driemeyer, Daniel E.

    1999-11-23

    Process for bonding a copper substrate to a tungsten substrate by providing a thin metallic adhesion promoting film bonded to a tungsten substrate and a functionally graded material (FGM) interlayer bonding the thin metallic adhesion promoting film to the copper substrate. The FGM interlayer is formed by thermal plasma spraying mixtures of copper powder and tungsten powder in a varied blending ratio such that the blending ratio of the copper powder and the tungsten powder that is fed to a plasma torch is intermittently adjusted to provide progressively higher copper content/tungsten content, by volume, ratio values in the interlayer in a lineal direction extending from the tungsten substrate towards the copper substrate. The resulting copper to tungsten joint well accommodates the difference in the coefficient of thermal expansion of the materials.

  15. Perspectives for spintronics in 2D materials

    NASA Astrophysics Data System (ADS)

    Han, Wei

    2016-03-01

    The past decade has been especially creative for spintronics since the (re)discovery of various two dimensional (2D) materials. Due to the unusual physical characteristics, 2D materials have provided new platforms to probe the spin interaction with other degrees of freedom for electrons, as well as to be used for novel spintronics applications. This review briefly presents the most important recent and ongoing research for spintronics in 2D materials.

  16. Quantitative 2D liquid-state NMR.

    PubMed

    Giraudeau, Patrick

    2014-06-01

    Two-dimensional (2D) liquid-state NMR has a very high potential to simultaneously determine the absolute concentration of small molecules in complex mixtures, thanks to its capacity to separate overlapping resonances. However, it suffers from two main drawbacks that probably explain its relatively late development. First, the 2D NMR signal is strongly molecule-dependent and site-dependent; second, the long duration of 2D NMR experiments prevents its general use for high-throughput quantitative applications and affects its quantitative performance. Fortunately, the last 10 years has witnessed an increasing number of contributions where quantitative approaches based on 2D NMR were developed and applied to solve real analytical issues. This review aims at presenting these recent efforts to reach a high trueness and precision in quantitative measurements by 2D NMR. After highlighting the interest of 2D NMR for quantitative analysis, the different strategies to determine the absolute concentrations from 2D NMR spectra are described and illustrated by recent applications. The last part of the manuscript concerns the recent development of fast quantitative 2D NMR approaches, aiming at reducing the experiment duration while preserving - or even increasing - the analytical performance. We hope that this comprehensive review will help readers to apprehend the current landscape of quantitative 2D NMR, as well as the perspectives that may arise from it.

  17. Ultrafast 2D-IR spectroelectrochemistry of flavin mononucleotide

    NASA Astrophysics Data System (ADS)

    El Khoury, Youssef; Van Wilderen, Luuk J. G. W.; Bredenbeck, Jens

    2015-06-01

    We demonstrate the coupling of ultrafast two-dimensional infrared (2D-IR) spectroscopy to electrochemistry in solution and apply it to flavin mononucleotide, an important cofactor of redox proteins. For this purpose, we designed a spectroelectrochemical cell optimized for 2D-IR measurements in reflection and measured the time-dependent 2D-IR spectra of the oxidized and reduced forms of flavin mononucleotide. The data show anharmonic coupling and vibrational energy transfer between different vibrational modes in the two redox species. Such information is inaccessible with redox-controlled steady-state FTIR spectroscopy. The wide range of applications offered by 2D-IR spectroscopy, such as sub-picosecond structure determination, IR band assignment via energy transfer, disentangling reaction mixtures through band connectivity in the 2D spectra, and the measurement of solvation dynamics and chemical exchange can now be explored under controlled redox potential. The development of this technique furthermore opens new horizons for studying the dynamics of redox proteins.

  18. Ultrafast 2D-IR spectroelectrochemistry of flavin mononucleotide.

    PubMed

    El Khoury, Youssef; Van Wilderen, Luuk J G W; Bredenbeck, Jens

    2015-06-01

    We demonstrate the coupling of ultrafast two-dimensional infrared (2D-IR) spectroscopy to electrochemistry in solution and apply it to flavin mononucleotide, an important cofactor of redox proteins. For this purpose, we designed a spectroelectrochemical cell optimized for 2D-IR measurements in reflection and measured the time-dependent 2D-IR spectra of the oxidized and reduced forms of flavin mononucleotide. The data show anharmonic coupling and vibrational energy transfer between different vibrational modes in the two redox species. Such information is inaccessible with redox-controlled steady-state FTIR spectroscopy. The wide range of applications offered by 2D-IR spectroscopy, such as sub-picosecond structure determination, IR band assignment via energy transfer, disentangling reaction mixtures through band connectivity in the 2D spectra, and the measurement of solvation dynamics and chemical exchange can now be explored under controlled redox potential. The development of this technique furthermore opens new horizons for studying the dynamics of redox proteins.

  19. In situ electrochemical investigation of tungsten electrochemical behavior during chemical mechanical polishing

    SciTech Connect

    Stein, D.J.; Cecchi, J.L.; Hetherington, D.; Guilinger, T.

    1998-09-01

    The electrochemical behavior of tungsten during chemical mechanical polishing (CMP) was observed in order to investigate a proposed blanket passivation and abrasion mechanism for tungsten removal. The experiments were performed in a cell that allowed electrochemical measurements to be made during polish. Polish rates were determined from the same samples used in the cell. Alumina-based polish slurries containing potassium iodate, ferric nitrate, or ammonium persulfate were used. DC polarization experiments show no evidence of passive film formation on the tungsten during polish. Tungsten oxidation rates measured during polish account for removal rates that are 1 to 2 orders of magnitude below the measured polish rate. Values of the charge-transfer resistance (measured by ac impedance spectroscopy) during polish are 1 to 2 orders of magnitude higher than expected from the polish rate, thus corroborating the dc-based data. Polish rates under potentiostatic conditions were also measured. The current required to maintain the metal anodic of the open-circuit potential is well below the current expected from measured polish rates, assuming complete oxidation of the tungsten. The polish rate during cathodic potentiostatic conditions ({minus}0.5 V with regard to the open-circuit potential) was similar to the polish rate at open circuit. The authors conclude that the formation of a blanket passive layer does not significantly contribute to tungsten removal during CMP.

  20. Staring 2-D hadamard transform spectral imager

    DOEpatents

    Gentry, Stephen M.; Wehlburg, Christine M.; Wehlburg, Joseph C.; Smith, Mark W.; Smith, Jody L.

    2006-02-07

    A staring imaging system inputs a 2D spatial image containing multi-frequency spectral information. This image is encoded in one dimension of the image with a cyclic Hadamarid S-matrix. The resulting image is detecting with a spatial 2D detector; and a computer applies a Hadamard transform to recover the encoded image.

  1. Oxycline formation induced by Fe(II) oxidation in a water reservoir affected by acid mine drainage modeled using a 2D hydrodynamic and water quality model - CE-QUAL-W2.

    PubMed

    Torres, Ester; Galván, Laura; Cánovas, Carlos Ruiz; Soria-Píriz, Sara; Arbat-Bofill, Marina; Nardi, Albert; Papaspyrou, Sokratis; Ayora, Carlos

    2016-08-15

    The Sancho reservoir is an acid mine drainage (AMD)-contaminated reservoir located in the Huelva province (SW Spain) with a pH close to 3.5. The water is only used for a refrigeration system of a paper mill. The Sancho reservoir is holomictic with one mixing period per year in the winter. During this mixing period, oxygenated water reaches the sediment, while under stratified conditions (the rest of the year) hypoxic conditions develop at the hypolimnion. A CE-QUAL-W2 model was calibrated for the Sancho Reservoir to predict the thermocline and oxycline formation, as well as the salinity, ammonium, nitrate, phosphorous, algal, chlorophyll-a, and iron concentrations. The version 3.7 of the model does not allow simulating the oxidation of Fe(II) in the water column, which limits the oxygen consumption of the organic matter oxidation. However, to evaluate the impact of Fe(II) oxidation on the oxycline formation, Fe(II) has been introduced into the model based on its relationship with labile dissolved organic matter (LDOM). The results show that Fe oxidation is the main factor responsible for the oxygen depletion in the hypolimnion of the Sancho Reservoir. The limiting factors for green algal growth have also been studied. The model predicted that ammonium, nitrate, and phosphate were not limiting factors for green algal growth. Light appeared to be one of the limiting factors for algal growth, while chlorophyll-a and dissolved oxygen concentrations could not be fully described. We hypothesize that dissolved CO2 is one of the limiting nutrients due to losses by the high acidity of the water column. The sensitivity tests carried out support this hypothesis. Two different remediation scenarios have been tested with the calibrated model: 1) an AMD passive treatment plant installed at the river, which removes completely Fe, and 2) different depth water extractions. If no Fe was introduced into the reservoir, water quality would significantly improve in only two years

  2. Oxycline formation induced by Fe(II) oxidation in a water reservoir affected by acid mine drainage modeled using a 2D hydrodynamic and water quality model - CE-QUAL-W2.

    PubMed

    Torres, Ester; Galván, Laura; Cánovas, Carlos Ruiz; Soria-Píriz, Sara; Arbat-Bofill, Marina; Nardi, Albert; Papaspyrou, Sokratis; Ayora, Carlos

    2016-08-15

    The Sancho reservoir is an acid mine drainage (AMD)-contaminated reservoir located in the Huelva province (SW Spain) with a pH close to 3.5. The water is only used for a refrigeration system of a paper mill. The Sancho reservoir is holomictic with one mixing period per year in the winter. During this mixing period, oxygenated water reaches the sediment, while under stratified conditions (the rest of the year) hypoxic conditions develop at the hypolimnion. A CE-QUAL-W2 model was calibrated for the Sancho Reservoir to predict the thermocline and oxycline formation, as well as the salinity, ammonium, nitrate, phosphorous, algal, chlorophyll-a, and iron concentrations. The version 3.7 of the model does not allow simulating the oxidation of Fe(II) in the water column, which limits the oxygen consumption of the organic matter oxidation. However, to evaluate the impact of Fe(II) oxidation on the oxycline formation, Fe(II) has been introduced into the model based on its relationship with labile dissolved organic matter (LDOM). The results show that Fe oxidation is the main factor responsible for the oxygen depletion in the hypolimnion of the Sancho Reservoir. The limiting factors for green algal growth have also been studied. The model predicted that ammonium, nitrate, and phosphate were not limiting factors for green algal growth. Light appeared to be one of the limiting factors for algal growth, while chlorophyll-a and dissolved oxygen concentrations could not be fully described. We hypothesize that dissolved CO2 is one of the limiting nutrients due to losses by the high acidity of the water column. The sensitivity tests carried out support this hypothesis. Two different remediation scenarios have been tested with the calibrated model: 1) an AMD passive treatment plant installed at the river, which removes completely Fe, and 2) different depth water extractions. If no Fe was introduced into the reservoir, water quality would significantly improve in only two years

  3. 2D materials for nanophotonic devices

    NASA Astrophysics Data System (ADS)

    Xu, Renjing; Yang, Jiong; Zhang, Shuang; Pei, Jiajie; Lu, Yuerui

    2015-12-01

    Two-dimensional (2D) materials have become very important building blocks for electronic, photonic, and phononic devices. The 2D material family has four key members, including the metallic graphene, transition metal dichalcogenide (TMD) layered semiconductors, semiconducting black phosphorous, and the insulating h-BN. Owing to the strong quantum confinements and defect-free surfaces, these atomically thin layers have offered us perfect platforms to investigate the interactions among photons, electrons and phonons. The unique interactions in these 2D materials are very important for both scientific research and application engineering. In this talk, I would like to briefly summarize and highlight the key findings, opportunities and challenges in this field. Next, I will introduce/highlight our recent achievements. We demonstrated atomically thin micro-lens and gratings using 2D MoS2, which is the thinnest optical component around the world. These devices are based on our discovery that the elastic light-matter interactions in highindex 2D materials is very strong. Also, I would like to introduce a new two-dimensional material phosphorene. Phosphorene has strongly anisotropic optical response, which creates 1D excitons in a 2D system. The strong confinement in phosphorene also enables the ultra-high trion (charged exciton) binding energies, which have been successfully measured in our experiments. Finally, I will briefly talk about the potential applications of 2D materials in energy harvesting.

  4. In vivo corrosion, tumor outcome, and microarray gene expression for two types of muscle-implanted tungsten alloys.

    PubMed

    Schuster, B E; Roszell, L E; Murr, L E; Ramirez, D A; Demaree, J D; Klotz, B R; Rosencrance, A B; Dennis, W E; Bao, W; Perkins, E J; Dillman, J F; Bannon, D I

    2012-11-15

    Tungsten alloys are composed of tungsten microparticles embedded in a solid matrix of transition metals such as nickel, cobalt, or iron. To understand the toxicology of these alloys, male F344 rats were intramuscularly implanted with pellets of tungsten/nickel/cobalt, tungsten/nickel/iron, or pure tungsten, with tantalum pellets as a negative control. Between 6 and 12 months, aggressive rhabdomyosarcomas formed around tungsten/nickel/cobalt pellets, while those of tungsten/nickel/iron or pure tungsten did not cause cancers. Electron microscopy showed a progressive corrosion of the matrix phase of tungsten/nickel/cobalt pellets over 6 months, accompanied by high urinary concentrations of nickel and cobalt. In contrast, non-carcinogenic tungsten/nickel/iron pellets were minimally corroded and urinary metals were low; these pellets having developed a surface oxide layer in vivo that may have restricted the mobilization of carcinogenic nickel. Microarray analysis of tumors revealed large changes in gene expression compared with normal muscle, with biological processes involving the cell cycle significantly up-regulated and those involved with muscle development and differentiation significantly down-regulated. Top KEGG pathways disrupted were adherens junction, p53 signaling, and the cell cycle. Chromosomal enrichment analysis of genes showed a highly significant impact at cytoband 7q22 (chromosome 7) which included mouse double minute (MDM2) and cyclin-dependant kinase (CDK4) as well as other genes associated with human sarcomas. In conclusion, the tumorigenic potential of implanted tungsten alloys is related to mobilization of carcinogenic metals nickel and cobalt from corroding pellets, while gene expression changes in the consequent tumors are similar to radiation induced animal sarcomas as well as sporadic human sarcomas.

  5. Tungsten Contact and Line Resistance Reduction with Advanced Pulsed Nucleation Layer and Low Resistivity Tungsten Treatment

    NASA Astrophysics Data System (ADS)

    Chandrashekar, Anand; Chen, Feng; Lin, Jasmine; Humayun, Raashina; Wongsenakhum, Panya; Chang, Sean; Danek, Michal; Itou, Takamasa; Nakayama, Tomoo; Kariya, Atsushi; Kawaguchi, Masazumi; Hizume, Shunichi

    2010-09-01

    This paper describes electrical testing results of new tungsten chemical vapor deposition (CVD-W) process concepts that were developed to address the W contact and bitline scaling issues on 55 nm node devices. Contact resistance (Rc) measurements in complementary metal oxide semiconductor (CMOS) devices indicate that the new CVD-W process for sub-32 nm and beyond - consisting of an advanced pulsed nucleation layer (PNL) combined with low resistivity tungsten (LRW) initiation - produces a 20-30% drop in Rc for diffused NiSi contacts. From cross-sectional bright field and dark field transmission electron microscopy (TEM) analysis, such Rc improvement can be attributed to improved plugfill and larger in-feature W grain size with the advanced PNL+LRW process. More experiments that measured contact resistance for different feature sizes point to favorable Rc scaling with the advanced PNL+LRW process. Finally, 40% improvement in line resistance was observed with this process as tested on 55 nm embedded dynamic random access memory (DRAM) devices, confirming that the advanced PNL+LRW process can be an effective metallization solution for sub-32 nm devices.

  6. Gas-tungsten arc welding of aluminum alloys

    DOEpatents

    Frye, L.D.

    1982-03-25

    The present invention is directed to a gas-tungsten arc welding method for joining together structures formed of aluminum alloy with these structures disposed contiguously to a heat-damagable substrate of a metal dissimilar to the aluminum alloy. The method of the present invention is practiced by diamond machining the fay surfaces of the aluminum alloy structures to profice a mirror finish thereon having a surface roughness in the order of about one microinch. The fay surface are aligned and heated sufficiently by the tungsten electrode to fuse the aluminum alloy continguous to the fay surfaces to effect the weld joint. The heat input used to provide an oxide-free weld is significantly less than that required if the fay surfaces were prepared by using conventional chemical and mechanical practices.

  7. Gas-tungsten arc welding of aluminum alloys

    DOEpatents

    Frye, Lowell D.

    1984-01-01

    A gas-tungsten arc welding method for joining together structures formed of aluminum alloy with these structures disposed contiguously to a heat-damagable substrate of a metal dissimilar to the aluminum alloy. The method of the present invention is practiced by diamond machining the fay surfaces of the aluminum alloy structures to provide a mirror finish thereon having a surface roughness in the order of about one microinch. The fay surfaces are aligned and heated sufficiently by the tungsten electrode to fuse the aluminum alloy contiguous to the fay surfaces to effect the weld joint. The heat input used to provide an oxide-free weld is significantly less than that required if the fay surfaces were prepared by using conventional chemical and mechanical practices.

  8. Potential role of CYP2D6 in the central nervous system

    PubMed Central

    Cheng, Jie; Zhen, Yueying; Miksys, Sharon; Beyoğlu, Diren; Krausz, Kristopher W.; Tyndale, Rachel F.; Yu, Aiming; Idle, Jeffrey R.; Gonzalez, Frank J.

    2013-01-01

    Cytochrome P450 2D6 (CYP2D6) is a pivotal enzyme responsible for a major human drug oxidation polymorphism in human populations. Distribution of CYP2D6 in brain and its role in serotonin metabolism suggest this CYP2D6 may have a function in central nervous system. To establish an efficient and accurate platform for the study of CYP2D6 in vivo, a transgenic human CYP2D6 (Tg-2D6) model was generated by transgenesis in wild-type C57BL/6 (WT) mice using a P1 phage artificial chromosome clone containing the complete human CYP2D locus, including CYP2D6 gene and 5’- and 3’- flanking sequences. Human CYP2D6 was expressed not only in the liver, but also in brain. The abundance of serotonin and 5-hydroxyindoleacetic acid in brain of Tg-2D6 is higher than in WT mice either basal levels or after harmaline induction. Metabolomics of brain homogenate and cerebrospinal fluid revealed a significant up-regulation of l-carnitine, acetyl-l-carnitine, pantothenic acid, dCDP, anandamide, N-acetylglucosaminylamine, and a down-regulation of stearoyl-l-carnitine in Tg-2D6 mice compared with WT mice. Anxiety tests indicate Tg-2D6 mice have a higher capability to adapt to anxiety. Overall, these findings indicate that the Tg-2D6 mouse model may serve as a valuable in vivo tool to determine CYP2D6-involved neurophysiological metabolism and function. PMID:23614566

  9. Photoelectrochemical water splitting at titanium dioxide nanotubes coated with tungsten trioxide

    SciTech Connect

    Park, Jong Hyeok; Park, O Ok; Kim, Sungwook

    2006-10-16

    The photocatalytic splitting of water into hydrogen and oxygen using solar light is a potentially clean and renewable source for hydrogen fuel. Titanium oxide nanotubes coated with tungsten oxide were prepared to harvest more solar light for the first time and characterized their water splitting efficiency. The tungsten trioxide coatings significantly enhanced the visible spectrum absorption of the titanium dioxide nanotube array, as well as their solar-spectrum induced photocurrents. For the sample, upon white light illumination at 150 mW/cm{sup 2}, hydrogen gas generated at the overall conversion efficiency of 0.87%.

  10. Fabrication of a tantalum-clad tungsten target for LANSCE

    NASA Astrophysics Data System (ADS)

    Nelson, A. T.; O'Toole, J. A.; Valicenti, R. A.; Maloy, S. A.

    2012-12-01

    Development of a solid state bonding technique suitable to clad tungsten targets with tantalum was completed to improve operation of the Los Alamos Neutron Science Centers spallation target. Significant deterioration of conventional bare tungsten targets has historically resulted in transfer of tungsten into the cooling system through corrosion resulting in increased radioactivity outside the target and reduction of delivered neutron flux. The fabrication method chosen to join the tantalum cladding to the tungsten was hot isostatic pressing (HIP) given the geometry constraints of a cylindrical assembly and previous success demonstrated at KENS. Nominal HIP parameters of 1500 °C, 200 MPa, and 3 h were selected based upon previous work. Development of the process included significant surface engineering controls and characterization given tantalums propensity for oxide and carbide formation at high temperatures. In addition to rigorous acid cleaning implemented at each step of the fabrication process, a three layer tantalum foil gettering system was devised such that any free oxygen and carbon impurities contained in the argon gas within the HIP vessel was mitigated to the extent possible before coming into contact with the tantalum cladding. The result of the numerous controls and refined techniques was negligible coarsening of the native Ta2O5 surface oxide, no measureable oxygen diffusion into the tantalum bulk, and no detectable carburization despite use of argon containing up to 5 ppm oxygen and up to 40 ppm total CO, CO2, or organic contaminants. Post bond characterization of the interface revealed continuous bonding with a few microns of species interdiffusion.

  11. "CLASPing" tungsten's effects on microtubules with "PINs".

    PubMed

    Adamakis, Ioannis Dimosthenis S; Panteris, Emmanuel; Eleftheriou, Eleftherios P

    2015-01-01

    Tungsten, supplied as sodium tungstate, inhibits root elongation in Arabidopsis thaliana, which has been attributed to a diminishing of PIN2 and PIN3 auxin efflux carriers. In this work, we sought to analyze the effect of tungsten on cortical microtubules and CLASP (Cytoplasmic Linker Associated Protein), which are also involved in the anisotropic cell expansion of root cells. Seedlings grown in a tungsten-free substrate for 4 d and then transplanted into a tungsten-containing substrate exhibited randomly oriented microtubules in a time-dependent manner. While tungsten had no effect on roots treated for 3 h, microtubule alignment was obviously affected in the transition and elongation zones after a 6, 12, 24, 48 h tungsten treatment, at prolonged tungsten administrations and in seedlings grown directly in the presence of tungsten. This change in microtubule orientation may be associated with the reduction of CLASP protein expression induced by tungsten, as evidenced in experiments with plants expressing the CLASP-GFP protein. A possible mechanism, by which the coordinated functions of CLASP, PIN2 and microtubules are affected, as revealed by inhibited root growth, is discussed. PMID:26313814

  12. High Urinary Tungsten Concentration Is Associated with Stroke in the National Health and Nutrition Examination Survey 1999–2010

    PubMed Central

    Tyrrell, Jessica; Galloway, Tamara S.; Abo-Zaid, Ghada; Melzer, David; Depledge, Michael H.; Osborne, Nicholas J.

    2013-01-01

    Background In recent years there has been an exponential increase in tungsten demand, potentially increasing human exposure to the metal. Currently, the toxicology of tungsten is poorly understood, but mounting evidence suggests that both the elemental metal and its alloys have cytotoxic effects. Here, we investigate the association between tungsten and cardiovascular disease (CVD) or stroke using six waves of the National Health and Nutrition Examination Survey (NHANES). Methods We investigated associations using crude and adjusted logistic regression models in a cohort of 8614 adults (18–74 years) with 193 reported stroke diagnoses and 428 reported diagnoses of CVD. We also stratified our data to characterize associations in a subset of younger individuals (18–50 years). Results Elevated tungsten concentrations were strongly associated with an increase in the prevalence of stroke, independent of typical risk factors (Odds Ratio (OR): 1.66, 95% Confidence Interval (95% CI): 1.17, 2.34). The association between tungsten and stroke in the young age category was still evident (OR: 2.17, 95% CI: 1.33, 3.53). Conclusion This study represents the most comprehensive analysis of the human health effects of tungsten to date. Individuals with higher urinary tungsten concentrations have double the odds of reported stroke. We hypothesize that the pathological pathway resulting from tungsten exposure may involve oxidative stress. PMID:24244278

  13. 2-d Finite Element Code Postprocessor

    1996-07-15

    ORION is an interactive program that serves as a postprocessor for the analysis programs NIKE2D, DYNA2D, TOPAZ2D, and CHEMICAL TOPAZ2D. ORION reads binary plot files generated by the two-dimensional finite element codes currently used by the Methods Development Group at LLNL. Contour and color fringe plots of a large number of quantities may be displayed on meshes consisting of triangular and quadrilateral elements. ORION can compute strain measures, interface pressures along slide lines, reaction forcesmore » along constrained boundaries, and momentum. ORION has been applied to study the response of two-dimensional solids and structures undergoing finite deformations under a wide variety of large deformation transient dynamic and static problems and heat transfer analyses.« less

  14. Matrix models of 2d gravity

    SciTech Connect

    Ginsparg, P.

    1991-01-01

    These are introductory lectures for a general audience that give an overview of the subject of matrix models and their application to random surfaces, 2d gravity, and string theory. They are intentionally 1.5 years out of date.

  15. Matrix models of 2d gravity

    SciTech Connect

    Ginsparg, P.

    1991-12-31

    These are introductory lectures for a general audience that give an overview of the subject of matrix models and their application to random surfaces, 2d gravity, and string theory. They are intentionally 1.5 years out of date.

  16. Brittle damage models in DYNA2D

    SciTech Connect

    Faux, D.R.

    1997-09-01

    DYNA2D is an explicit Lagrangian finite element code used to model dynamic events where stress wave interactions influence the overall response of the system. DYNA2D is often used to model penetration problems involving ductile-to-ductile impacts; however, with the advent of the use of ceramics in the armor-anti-armor community and the need to model damage to laser optics components, good brittle damage models are now needed in DYNA2D. This report will detail the implementation of four brittle damage models in DYNA2D, three scalar damage models and one tensor damage model. These new brittle damage models are then used to predict experimental results from three distinctly different glass damage problems.

  17. In vivo corrosion, tumor outcome, and microarray gene expression for two types of muscle-implanted tungsten alloys

    SciTech Connect

    Schuster, B.E.; Roszell, L.E.; Murr, L.E.; Ramirez, D.A.; Demaree, J.D.; Klotz, B.R.; Rosencrance, A.B.; Dennis, W.E.; Bao, W.; Perkins, E.J.; Dillman, J.F.; Bannon, D.I.

    2012-11-15

    Tungsten alloys are composed of tungsten microparticles embedded in a solid matrix of transition metals such as nickel, cobalt, or iron. To understand the toxicology of these alloys, male F344 rats were intramuscularly implanted with pellets of tungsten/nickel/cobalt, tungsten/nickel/iron, or pure tungsten, with tantalum pellets as a negative control. Between 6 and 12 months, aggressive rhabdomyosarcomas formed around tungsten/nickel/cobalt pellets, while those of tungsten/nickel/iron or pure tungsten did not cause cancers. Electron microscopy showed a progressive corrosion of the matrix phase of tungsten/nickel/cobalt pellets over 6 months, accompanied by high urinary concentrations of nickel and cobalt. In contrast, non-carcinogenic tungsten/nickel/iron pellets were minimally corroded and urinary metals were low; these pellets having developed a surface oxide layer in vivo that may have restricted the mobilization of carcinogenic nickel. Microarray analysis of tumors revealed large changes in gene expression compared with normal muscle, with biological processes involving the cell cycle significantly up‐regulated and those involved with muscle development and differentiation significantly down‐regulated. Top KEGG pathways disrupted were adherens junction, p53 signaling, and the cell cycle. Chromosomal enrichment analysis of genes showed a highly significant impact at cytoband 7q22 (chromosome 7) which included mouse double minute (MDM2) and cyclin‐dependant kinase (CDK4) as well as other genes associated with human sarcomas. In conclusion, the tumorigenic potential of implanted tungsten alloys is related to mobilization of carcinogenic metals nickel and cobalt from corroding pellets, while gene expression changes in the consequent tumors are similar to radiation induced animal sarcomas as well as sporadic human sarcomas. -- Highlights: ► Tungsten/nickel/cobalt, tungsten/nickel/iron, and pure tungsten were studied. ► Male Fischer rats implanted with

  18. Chemical Approaches to 2D Materials.

    PubMed

    Samorì, Paolo; Palermo, Vincenzo; Feng, Xinliang

    2016-08-01

    Chemistry plays an ever-increasing role in the production, functionalization, processing and applications of graphene and other 2D materials. This special issue highlights a selection of enlightening chemical approaches to 2D materials, which nicely reflect the breadth of the field and convey the excitement of the individuals involved in it, who are trying to translate graphene and related materials from the laboratory into a real, high-impact technology. PMID:27478083

  19. Chemical Approaches to 2D Materials.

    PubMed

    Samorì, Paolo; Palermo, Vincenzo; Feng, Xinliang

    2016-08-01

    Chemistry plays an ever-increasing role in the production, functionalization, processing and applications of graphene and other 2D materials. This special issue highlights a selection of enlightening chemical approaches to 2D materials, which nicely reflect the breadth of the field and convey the excitement of the individuals involved in it, who are trying to translate graphene and related materials from the laboratory into a real, high-impact technology.

  20. Glitter in a 2D monolayer.

    PubMed

    Yang, Li-Ming; Dornfeld, Matthew; Frauenheim, Thomas; Ganz, Eric

    2015-10-21

    We predict a highly stable and robust atomically thin gold monolayer with a hexagonal close packed lattice stabilized by metallic bonding with contributions from strong relativistic effects and aurophilic interactions. We have shown that the framework of the Au monolayer can survive 10 ps MD annealing simulations up to 1400 K. The framework is also able to survive large motions out of the plane. Due to the smaller number of bonds per atom in the 2D layer compared to the 3D bulk we observe significantly enhanced energy per bond (0.94 vs. 0.52 eV per bond). This is similar to the increase in bond strength going from 3D diamond to 2D graphene. It is a non-magnetic metal, and was found to be the global minima in the 2D space. Phonon dispersion calculations demonstrate high kinetic stability with no negative modes. This 2D gold monolayer corresponds to the top monolayer of the bulk Au(111) face-centered cubic lattice. The close-packed lattice maximizes the aurophilic interactions. We find that the electrons are completely delocalized in the plane and behave as 2D nearly free electron gas. We hope that the present work can inspire the experimental fabrication of novel free standing 2D metal systems.

  1. 2d index and surface operators

    NASA Astrophysics Data System (ADS)

    Gadde, Abhijit; Gukov, Sergei

    2014-03-01

    In this paper we compute the superconformal index of 2d (2, 2) supersymmetric gauge theories. The 2d superconformal index, a.k.a. flavored elliptic genus, is computed by a unitary matrix integral much like the matrix integral that computes the 4d superconformal index. We compute the 2d index explicitly for a number of examples. In the case of abelian gauge theories we see that the index is invariant under flop transition and under CY-LG correspondence. The index also provides a powerful check of the Seiberg-type duality for non-abelian gauge theories discovered by Hori and Tong. In the later half of the paper, we study half-BPS surface operators in = 2 super-conformal gauge theories. They are engineered by coupling the 2d (2, 2) supersymmetric gauge theory living on the support of the surface operator to the 4d = 2 theory, so that different realizations of the same surface operator with a given Levi type are related by a 2d analogue of the Seiberg duality. The index of this coupled system is computed by using the tools developed in the first half of the paper. The superconformal index in the presence of surface defect is expected to be invariant under generalized S-duality. We demonstrate that it is indeed the case. In doing so the Seiberg-type duality of the 2d theory plays an important role.

  2. 40 CFR 421.100 - Applicability: Description of the primary tungsten subcategory.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... primary tungsten subcategory. 421.100 Section 421.100 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Primary Tungsten Subcategory § 421.100 Applicability: Description of the primary tungsten... tungsten at primary tungsten facilities....

  3. 40 CFR 421.100 - Applicability: Description of the primary tungsten subcategory.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... primary tungsten subcategory. 421.100 Section 421.100 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Primary Tungsten Subcategory § 421.100 Applicability: Description of the primary tungsten... tungsten at primary tungsten facilities....

  4. 40 CFR 421.100 - Applicability: Description of the primary tungsten subcategory.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... primary tungsten subcategory. 421.100 Section 421.100 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Primary Tungsten Subcategory § 421.100 Applicability: Description of the primary tungsten... tungsten at primary tungsten facilities....

  5. 40 CFR 421.100 - Applicability: Description of the primary tungsten subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... primary tungsten subcategory. 421.100 Section 421.100 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Primary Tungsten Subcategory § 421.100 Applicability: Description of the primary tungsten... tungsten at primary tungsten facilities....

  6. 40 CFR 421.100 - Applicability: Description of the primary tungsten subcategory.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... primary tungsten subcategory. 421.100 Section 421.100 Protection of Environment ENVIRONMENTAL PROTECTION... CATEGORY Primary Tungsten Subcategory § 421.100 Applicability: Description of the primary tungsten... tungsten at primary tungsten facilities....

  7. 2D-2D tunneling field-effect transistors using WSe2/SnSe2 heterostructures

    NASA Astrophysics Data System (ADS)

    Roy, Tania; Tosun, Mahmut; Hettick, Mark; Ahn, Geun Ho; Hu, Chenming; Javey, Ali

    2016-02-01

    Two-dimensional materials present a versatile platform for developing steep transistors due to their uniform thickness and sharp band edges. We demonstrate 2D-2D tunneling in a WSe2/SnSe2 van der Waals vertical heterojunction device, where WSe2 is used as the gate controlled p-layer and SnSe2 is the degenerately n-type layer. The van der Waals gap facilitates the regulation of band alignment at the heterojunction, without the necessity of a tunneling barrier. ZrO2 is used as the gate dielectric, allowing the scaling of gate oxide to improve device subthreshold swing. Efficient gate control and clean interfaces yield a subthreshold swing of ˜100 mV/dec for >2 decades of drain current at room temperature, hitherto unobserved in 2D-2D tunneling devices. The subthreshold swing is independent of temperature, which is a clear signature of band-to-band tunneling at the heterojunction. A maximum switching ratio ION/IOFF of 107 is obtained. Negative differential resistance in the forward bias characteristics is observed at 77 K. This work bodes well for the possibilities of two-dimensional materials for the realization of energy-efficient future-generation electronics.

  8. Tungsten coating for improved wear resistance and reliability of microelectromechanical devices

    DOEpatents

    Fleming, James G.; Mani, Seethambal S.; Sniegowski, Jeffry J.; Blewer, Robert S.

    2001-01-01

    A process is disclosed whereby a 5-50-nanometer-thick conformal tungsten coating can be formed over exposed semiconductor surfaces (e.g. silicon, germanium or silicon carbide) within a microelectromechanical (MEM) device for improved wear resistance and reliability. The tungsten coating is formed after cleaning the semiconductor surfaces to remove any organic material and oxide film from the surface. A final in situ cleaning step is performed by heating a substrate containing the MEM device to a temperature in the range of 200-600 .degree. C. in the presence of gaseous nitrogen trifluoride (NF.sub.3). The tungsten coating can then be formed by a chemical reaction between the semiconductor surfaces and tungsten hexafluoride (WF.sub.6) at an elevated temperature, preferably about 450.degree. C. The tungsten deposition process is self-limiting and covers all exposed semiconductor surfaces including surfaces in close contact. The present invention can be applied to many different types of MEM devices including microrelays, micromirrors and microengines. Additionally, the tungsten wear-resistant coating of the present invention can be used to enhance the hardness, wear resistance, electrical conductivity, optical reflectivity and chemical inertness of one or more semiconductor surfaces within a MEM device.

  9. Novel properties of Tungsten ditelluride

    NASA Astrophysics Data System (ADS)

    Liu, Huimei; National Laboratory of Solid State Microstructures, School of Physics, Collaborative Innovation Cent Collaboration

    Tungsten ditelluride has attracted intense research interest due to the recent discovery of its large unsaturated magnetoresistance up to 60 Tesla. By using density functional theory calculations, we qualitatively reproduced the observed spin texture. Since the spin texture would forbid back scatterings that are directly involved in the resistivity, we suggest that the SOC and the related spin and orbital angular momentum textures may play an important role in the anomalously large magnetoresistance of WTe2. Motivated by the presence of a small, sensitive Fermi surface of 5d electronic orbitals, we also boost the electronic properties by applying a high pressure, and introduce superconductivity successfully.

  10. Mirrorlike pulsed laser deposited tungsten thin film

    SciTech Connect

    Mostako, A. T. T.; Khare, Alika; Rao, C. V. S.

    2011-01-15

    Mirrorlike tungsten thin films on stainless steel substrate deposited via pulsed laser deposition technique in vacuum (10{sup -5} Torr) is reported, which may find direct application as first mirror in fusion devices. The crystal structure of tungsten film is analyzed using x-ray diffraction pattern, surface morphology of the tungsten films is studied with scanning electron microscope and atomic force microscope. The film composition is identified using energy dispersive x-ray. The specular and diffuse reflectivities with respect to stainless steel substrate of the tungsten films are recorded with FTIR spectra. The thickness and the optical quality of pulsed laser deposition deposited films are tested via interferometric technique. The reflectivity is approaching about that of the bulk for the tungsten film of thickness {approx}782 nm.

  11. Mirrorlike pulsed laser deposited tungsten thin film.

    PubMed

    Mostako, A T T; Rao, C V S; Khare, Alika

    2011-01-01

    Mirrorlike tungsten thin films on stainless steel substrate deposited via pulsed laser deposition technique in vacuum (10(-5) Torr) is reported, which may find direct application as first mirror in fusion devices. The crystal structure of tungsten film is analyzed using x-ray diffraction pattern, surface morphology of the tungsten films is studied with scanning electron microscope and atomic force microscope. The film composition is identified using energy dispersive x-ray. The specular and diffuse reflectivities with respect to stainless steel substrate of the tungsten films are recorded with FTIR spectra. The thickness and the optical quality of pulsed laser deposition deposited films are tested via interferometric technique. The reflectivity is approaching about that of the bulk for the tungsten film of thickness ∼782 nm. PMID:21280810

  12. Strengthening mechanisms of tungsten powder reinforced uranium

    SciTech Connect

    Lewis, M.A.K.; Hill, M.A.; Rollett, A.D.; Dunn, P.S.; Mortensen, A.; Massachusetts Inst. of Tech., Cambridge, MA )

    1989-01-01

    Tungsten powder reinforced uranium exhibits a three-fold increase in yield strength due to precipitation hardening. The tungsten-rich interphase precipitates form at moving phase boundaries during slow cooling. Further increases in yield strength, attained with increasing tungsten content, are due to composite strengthening; this is verified by increasing elastic modulus with increasing tungsten content. Age hardening behavior is observed, with strengthening occurring at aging temperatures low in the alpha phase. Aging higher in alpha gives initial strengthening followed by rapid overaging. Beta phase aging results in a very soft structure with precipitates visible optically. Wrought material exhibits significant strain hardening as well as composite strengthening due to elongation of the tungsten particles. 7 refs., 15 figs., 4 tabs.

  13. Strengthening mechanisms of tungsten powder reinforced uranium

    SciTech Connect

    Krawizcki, M.A.

    1990-04-01

    Tungsten powder reinforced uranium composites exhibit a three-fold increase in yield strength due to precipitation hardening. The tungsten-rich interphase precipitates form at the moving beta to alpha phase boundary during slow cooling. Further increases in yield strength, attained with increasing tungsten content, are due to composite strengthening. The composite strengthening is verified by increasing elastic modulus with increasing tungsten content. Age hardening behavior is observed, with strengthening occurring at aging temperatures low, in the alpha phase. Temperatures higher in alpha give initial strengthening followed by rapid overaging. Beta phase aging temperatures result in a very soft structure with interphase precipitates observable optically. Wrought material exhibits significant strain hardening as well as composite strengthening due to elongation of the tungsten particles. 36 refs., 36 figs., 10 tabs.

  14. Orthotropic Piezoelectricity in 2D Nanocellulose

    NASA Astrophysics Data System (ADS)

    García, Y.; Ruiz-Blanco, Yasser B.; Marrero-Ponce, Yovani; Sotomayor-Torres, C. M.

    2016-10-01

    The control of electromechanical responses within bonding regions is essential to face frontier challenges in nanotechnologies, such as molecular electronics and biotechnology. Here, we present Iβ-nanocellulose as a potentially new orthotropic 2D piezoelectric crystal. The predicted in-layer piezoelectricity is originated on a sui-generis hydrogen bonds pattern. Upon this fact and by using a combination of ab-initio and ad-hoc models, we introduce a description of electrical profiles along chemical bonds. Such developments lead to obtain a rationale for modelling the extended piezoelectric effect originated within bond scales. The order of magnitude estimated for the 2D Iβ-nanocellulose piezoelectric response, ~pm V‑1, ranks this material at the level of currently used piezoelectric energy generators and new artificial 2D designs. Such finding would be crucial for developing alternative materials to drive emerging nanotechnologies.

  15. Orthotropic Piezoelectricity in 2D Nanocellulose

    PubMed Central

    García, Y.; Ruiz-Blanco, Yasser B.; Marrero-Ponce, Yovani; Sotomayor-Torres, C. M.

    2016-01-01

    The control of electromechanical responses within bonding regions is essential to face frontier challenges in nanotechnologies, such as molecular electronics and biotechnology. Here, we present Iβ-nanocellulose as a potentially new orthotropic 2D piezoelectric crystal. The predicted in-layer piezoelectricity is originated on a sui-generis hydrogen bonds pattern. Upon this fact and by using a combination of ab-initio and ad-hoc models, we introduce a description of electrical profiles along chemical bonds. Such developments lead to obtain a rationale for modelling the extended piezoelectric effect originated within bond scales. The order of magnitude estimated for the 2D Iβ-nanocellulose piezoelectric response, ~pm V−1, ranks this material at the level of currently used piezoelectric energy generators and new artificial 2D designs. Such finding would be crucial for developing alternative materials to drive emerging nanotechnologies. PMID:27708364

  16. 2D microwave imaging reflectometer electronics

    SciTech Connect

    Spear, A. G.; Domier, C. W. Hu, X.; Muscatello, C. M.; Ren, X.; Luhmann, N. C.; Tobias, B. J.

    2014-11-15

    A 2D microwave imaging reflectometer system has been developed to visualize electron density fluctuations on the DIII-D tokamak. Simultaneously illuminated at four probe frequencies, large aperture optics image reflections from four density-dependent cutoff surfaces in the plasma over an extended region of the DIII-D plasma. Localized density fluctuations in the vicinity of the plasma cutoff surfaces modulate the plasma reflections, yielding a 2D image of electron density fluctuations. Details are presented of the receiver down conversion electronics that generate the in-phase (I) and quadrature (Q) reflectometer signals from which 2D density fluctuation data are obtained. Also presented are details on the control system and backplane used to manage the electronics as well as an introduction to the computer based control program.

  17. Optical modulators with 2D layered materials

    NASA Astrophysics Data System (ADS)

    Sun, Zhipei; Martinez, Amos; Wang, Feng

    2016-04-01

    Light modulation is an essential operation in photonics and optoelectronics. With existing and emerging technologies increasingly demanding compact, efficient, fast and broadband optical modulators, high-performance light modulation solutions are becoming indispensable. The recent realization that 2D layered materials could modulate light with superior performance has prompted intense research and significant advances, paving the way for realistic applications. In this Review, we cover the state of the art of optical modulators based on 2D materials, including graphene, transition metal dichalcogenides and black phosphorus. We discuss recent advances employing hybrid structures, such as 2D heterostructures, plasmonic structures, and silicon and fibre integrated structures. We also take a look at the future perspectives and discuss the potential of yet relatively unexplored mechanisms, such as magneto-optic and acousto-optic modulation.

  18. Inkjet printing of 2D layered materials.

    PubMed

    Li, Jiantong; Lemme, Max C; Östling, Mikael

    2014-11-10

    Inkjet printing of 2D layered materials, such as graphene and MoS2, has attracted great interests for emerging electronics. However, incompatible rheology, low concentration, severe aggregation and toxicity of solvents constitute critical challenges which hamper the manufacturing efficiency and product quality. Here, we introduce a simple and general technology concept (distillation-assisted solvent exchange) to efficiently overcome these challenges. By implementing the concept, we have demonstrated excellent jetting performance, ideal printing patterns and a variety of promising applications for inkjet printing of 2D layered materials. PMID:25169938

  19. Inkjet printing of 2D layered materials.

    PubMed

    Li, Jiantong; Lemme, Max C; Östling, Mikael

    2014-11-10

    Inkjet printing of 2D layered materials, such as graphene and MoS2, has attracted great interests for emerging electronics. However, incompatible rheology, low concentration, severe aggregation and toxicity of solvents constitute critical challenges which hamper the manufacturing efficiency and product quality. Here, we introduce a simple and general technology concept (distillation-assisted solvent exchange) to efficiently overcome these challenges. By implementing the concept, we have demonstrated excellent jetting performance, ideal printing patterns and a variety of promising applications for inkjet printing of 2D layered materials.

  20. Development of tungsten fibre-reinforced tungsten composites towards their use in DEMO—potassium doped tungsten wire

    NASA Astrophysics Data System (ADS)

    Riesch, J.; Han, Y.; Almanstötter, J.; Coenen, J. W.; Höschen, T.; Jasper, B.; Zhao, P.; Linsmeier, Ch; Neu, R.

    2016-02-01

    For the next step fusion reactor the use of tungsten is inevitable to suppress erosion and allow operation at elevated temperature and high heat loads. Tungsten fibre-reinforced composites overcome the intrinsic brittleness of tungsten and its susceptibility to operation embrittlement and thus allow its use as a structural as well as an armour material. That this concept works in principle has been shown in recent years. In this contribution we present a development approach towards its use in a future fusion reactor. A multilayer approach is needed addressing all composite constituents and manufacturing steps. A huge potential lies in the optimization of the tungsten wire used as fibre. We discuss this aspect and present studies on potassium doped tungsten wire in detail. This wire, utilized in the illumination industry, could be a replacement for the so far used pure tungsten wire due to its superior high temperature properties. In tensile tests the wire showed high strength and ductility up to an annealing temperature of 2200 K. The results show that the use of doped tungsten wire could increase the allowed fabrication temperature and the overall working temperature of the composite itself.

  1. 2D Magneto-Optical Trapping of Diatomic Molecules

    NASA Astrophysics Data System (ADS)

    Hummon, Matthew T.; Yeo, Mark; Stuhl, Benjamin K.; Collopy, Alejandra L.; Xia, Yong; Ye, Jun

    2013-04-01

    We demonstrate one- and two-dimensional transverse laser cooling and magneto-optical trapping of the polar molecule yttrium (II) oxide (YO). In a 1D magneto-optical trap (MOT), we characterize the magneto-optical trapping force and decrease the transverse temperature by an order of magnitude, from 25 to 2 mK, limited by interaction time. In a 2D MOT, we enhance the intensity of the YO beam and reduce the transverse temperature in both transverse directions. The approach demonstrated here can be applied to many molecular species and can also be extended to 3D.

  2. Interferometric Motion Detection in Atomic Layer 2D Nanostructures: Visualizing Signal Transduction Efficiency and Optimization Pathways.

    PubMed

    Wang, Zenghui; Feng, Philip X-L

    2016-01-01

    Atomic layer crystals are emerging building blocks for enabling new two-dimensional (2D) nanomechanical systems, whose motions can be coupled to other attractive physical properties in such 2D systems. Optical interferometry has been very effective in reading out the infinitesimal motions of these 2D structures and spatially resolving different modes. To quantitatively understand the detection efficiency and its dependence on the device parameters and interferometric conditions, here we present a systematic study of the intrinsic motion responsivity in 2D nanomechanical systems using a Fresnel-law-based model. We find that in monolayer to 14-layer structures, MoS2 offers the highest responsivity among graphene, h-BN, and MoS2 devices and for the three commonly used visible laser wavelengths (633, 532, and 405 nm). We also find that the vacuum gap resulting from the widely used 300 nm-oxide substrate in making 2D devices, fortunately, leads to close-to-optimal responsivity for a wide range of 2D flakes. Our results elucidate and graphically visualize the dependence of motion transduction responsivity upon 2D material type and number of layers, vacuum gap, oxide thickness, and detecting wavelength, thus providing design guidelines for constructing 2D nanomechanical systems with optimal optical motion readout. PMID:27464908

  3. Interferometric Motion Detection in Atomic Layer 2D Nanostructures: Visualizing Signal Transduction Efficiency and Optimization Pathways.

    PubMed

    Wang, Zenghui; Feng, Philip X-L

    2016-07-28

    Atomic layer crystals are emerging building blocks for enabling new two-dimensional (2D) nanomechanical systems, whose motions can be coupled to other attractive physical properties in such 2D systems. Optical interferometry has been very effective in reading out the infinitesimal motions of these 2D structures and spatially resolving different modes. To quantitatively understand the detection efficiency and its dependence on the device parameters and interferometric conditions, here we present a systematic study of the intrinsic motion responsivity in 2D nanomechanical systems using a Fresnel-law-based model. We find that in monolayer to 14-layer structures, MoS2 offers the highest responsivity among graphene, h-BN, and MoS2 devices and for the three commonly used visible laser wavelengths (633, 532, and 405 nm). We also find that the vacuum gap resulting from the widely used 300 nm-oxide substrate in making 2D devices, fortunately, leads to close-to-optimal responsivity for a wide range of 2D flakes. Our results elucidate and graphically visualize the dependence of motion transduction responsivity upon 2D material type and number of layers, vacuum gap, oxide thickness, and detecting wavelength, thus providing design guidelines for constructing 2D nanomechanical systems with optimal optical motion readout.

  4. Interferometric Motion Detection in Atomic Layer 2D Nanostructures: Visualizing Signal Transduction Efficiency and Optimization Pathways

    NASA Astrophysics Data System (ADS)

    Wang, Zenghui; Feng, Philip X.-L.

    2016-07-01

    Atomic layer crystals are emerging building blocks for enabling new two-dimensional (2D) nanomechanical systems, whose motions can be coupled to other attractive physical properties in such 2D systems. Optical interferometry has been very effective in reading out the infinitesimal motions of these 2D structures and spatially resolving different modes. To quantitatively understand the detection efficiency and its dependence on the device parameters and interferometric conditions, here we present a systematic study of the intrinsic motion responsivity in 2D nanomechanical systems using a Fresnel-law-based model. We find that in monolayer to 14-layer structures, MoS2 offers the highest responsivity among graphene, h-BN, and MoS2 devices and for the three commonly used visible laser wavelengths (633, 532, and 405 nm). We also find that the vacuum gap resulting from the widely used 300 nm-oxide substrate in making 2D devices, fortunately, leads to close-to-optimal responsivity for a wide range of 2D flakes. Our results elucidate and graphically visualize the dependence of motion transduction responsivity upon 2D material type and number of layers, vacuum gap, oxide thickness, and detecting wavelength, thus providing design guidelines for constructing 2D nanomechanical systems with optimal optical motion readout.

  5. Interferometric Motion Detection in Atomic Layer 2D Nanostructures: Visualizing Signal Transduction Efficiency and Optimization Pathways

    PubMed Central

    Wang, Zenghui; Feng, Philip X.-L.

    2016-01-01

    Atomic layer crystals are emerging building blocks for enabling new two-dimensional (2D) nanomechanical systems, whose motions can be coupled to other attractive physical properties in such 2D systems. Optical interferometry has been very effective in reading out the infinitesimal motions of these 2D structures and spatially resolving different modes. To quantitatively understand the detection efficiency and its dependence on the device parameters and interferometric conditions, here we present a systematic study of the intrinsic motion responsivity in 2D nanomechanical systems using a Fresnel-law-based model. We find that in monolayer to 14-layer structures, MoS2 offers the highest responsivity among graphene, h-BN, and MoS2 devices and for the three commonly used visible laser wavelengths (633, 532, and 405 nm). We also find that the vacuum gap resulting from the widely used 300 nm-oxide substrate in making 2D devices, fortunately, leads to close-to-optimal responsivity for a wide range of 2D flakes. Our results elucidate and graphically visualize the dependence of motion transduction responsivity upon 2D material type and number of layers, vacuum gap, oxide thickness, and detecting wavelength, thus providing design guidelines for constructing 2D nanomechanical systems with optimal optical motion readout. PMID:27464908

  6. Parallel stitching of 2D materials

    DOE PAGES

    Ling, Xi; Wu, Lijun; Lin, Yuxuan; Ma, Qiong; Wang, Ziqiang; Song, Yi; Yu, Lili; Huang, Shengxi; Fang, Wenjing; Zhang, Xu; et al

    2016-01-27

    Diverse parallel stitched 2D heterostructures, including metal–semiconductor, semiconductor–semiconductor, and insulator–semiconductor, are synthesized directly through selective “sowing” of aromatic molecules as the seeds in the chemical vapor deposition (CVD) method. Lastly, the methodology enables the large-scale fabrication of lateral heterostructures, which offers tremendous potential for its application in integrated circuits.

  7. Parallel Stitching of 2D Materials.

    PubMed

    Ling, Xi; Lin, Yuxuan; Ma, Qiong; Wang, Ziqiang; Song, Yi; Yu, Lili; Huang, Shengxi; Fang, Wenjing; Zhang, Xu; Hsu, Allen L; Bie, Yaqing; Lee, Yi-Hsien; Zhu, Yimei; Wu, Lijun; Li, Ju; Jarillo-Herrero, Pablo; Dresselhaus, Mildred; Palacios, Tomás; Kong, Jing

    2016-03-23

    Diverse parallel stitched 2D heterostructures, including metal-semiconductor, semiconductor-semiconductor, and insulator-semiconductor, are synthesized directly through selective "sowing" of aromatic molecules as the seeds in the chemical vapor deposition (CVD) method. The methodology enables the large-scale fabrication of lateral heterostructures, which offers tremendous potential for its application in integrated circuits.

  8. Pyranopterin conformation defines the function of molybdenum and tungsten enzymes.

    PubMed

    Rothery, Richard A; Stein, Benjamin; Solomonson, Matthew; Kirk, Martin L; Weiner, Joel H

    2012-09-11

    We have analyzed the conformations of 319 pyranopterins in 102 protein structures of mononuclear molybdenum and tungsten enzymes. These span a continuum between geometries anticipated for quinonoid dihydro, tetrahydro, and dihydro oxidation states. We demonstrate that pyranopterin conformation is correlated with the protein folds defining the three major mononuclear molybdenum and tungsten enzyme families, and that binding-site micro-tuning controls pyranopterin oxidation state. Enzymes belonging to the bacterial dimethyl sulfoxide reductase (DMSOR) family contain a metal-bis-pyranopterin cofactor, the two pyranopterins of which have distinct conformations, with one similar to the predicted tetrahydro form, and the other similar to the predicted dihydro form. Enzymes containing a single pyranopterin belong to either the xanthine dehydrogenase (XDH) or sulfite oxidase (SUOX) families, and these have pyranopterin conformations similar to those predicted for tetrahydro and dihydro forms, respectively. This work provides keen insight into the roles of pyranopterin conformation and oxidation state in catalysis, redox potential modulation of the metal site, and catalytic function.

  9. Plasma as a tool for growth of 1D and 2D nanomaterials and their conversions

    NASA Astrophysics Data System (ADS)

    Cvelbar, Uros

    2015-09-01

    The growth of 1D and 2D nanostructures in low pressure oxygen plasma is presented with the special stress on metal-oxide nanowires and their deterministic growth mechanisms. Since the resulting nanostructures not always have required properties for applications their modifications are required. Therefore their conversions into different oxides or sulphites/nitrides are required with either molecules, atoms, electrons or photons.

  10. Environmental fate of tungsten from military use.

    PubMed

    Clausen, Jay L; Korte, Nic

    2009-04-01

    This manuscript describes the distribution, fate and transport of tungsten used in training rounds at three small arms ranges at Camp Edwards on the Massachusetts Military Reservation (MMR), USA. Practice with tungsten/nylon rounds began in 2000 subsequent to a 1997 US Environmental Protection Agency ban on training with lead. Training with the tungsten rounds was halted in 2005 because of concerns regarding tungsten's environmental mobility and potential toxicity. This study, therefore, examines how tungsten partitions in the environment when fired on a small arms training range. Soil sampling revealed surface soil concentrations, highest at the berm face, up to 2080 mg/kg. Concentrations decreased rapidly with depth--at least by an order of magnitude by 25 cm. Nonetheless, tungsten concentrations remained above background to at least 150 cm. Pore-water samples from lysimeters installed in berm areas revealed a range of concentrations (<1-400 mg/L) elevated with respect to background although there was no discernable trend with depth. Groundwater monitoring well samples collected approximately 30 m below ground surface showed tungsten (0.001-0.56 mg/L) attributable to range use.

  11. Environmental fate of tungsten from military use.

    PubMed

    Clausen, Jay L; Korte, Nic

    2009-04-01

    This manuscript describes the distribution, fate and transport of tungsten used in training rounds at three small arms ranges at Camp Edwards on the Massachusetts Military Reservation (MMR), USA. Practice with tungsten/nylon rounds began in 2000 subsequent to a 1997 US Environmental Protection Agency ban on training with lead. Training with the tungsten rounds was halted in 2005 because of concerns regarding tungsten's environmental mobility and potential toxicity. This study, therefore, examines how tungsten partitions in the environment when fired on a small arms training range. Soil sampling revealed surface soil concentrations, highest at the berm face, up to 2080 mg/kg. Concentrations decreased rapidly with depth--at least by an order of magnitude by 25 cm. Nonetheless, tungsten concentrations remained above background to at least 150 cm. Pore-water samples from lysimeters installed in berm areas revealed a range of concentrations (<1-400 mg/L) elevated with respect to background although there was no discernable trend with depth. Groundwater monitoring well samples collected approximately 30 m below ground surface showed tungsten (0.001-0.56 mg/L) attributable to range use. PMID:19217645

  12. Single crystal tungsten kinetic energy penetrators

    SciTech Connect

    Cline, C.F.; Gogolewski, R.P.

    1992-05-01

    We have explored the terminal ballistic performance of single crystal tungsten as a kinetic energy penetrator. Scientific speculation as to the anticipated penetration performance and nature of the interaction between such a kinetic energy penetrator and semi-infinite and spaced metallic targets has led us to perform laboratory scale experiments and metallographic examinations of post-impact penetrator materials. The single tungsten crystals were ground into kinetic energy penetrators with the [l angle]111[r angle] and [l angle]100[r angle] crystal direction being coincident with the axis of symmetry of the penetrators. The crystals were electro-polished to their final diameter. We, compared the terminal performance at current ordnance speeds of [l angle]111[r angle] single crystal tungsten to 90W-10 (NiFe) cemented tungsten and textured pure tungsten in laboratory scale ballistic experiments against a spaced steel (triple) target at sixty-five degrees obliquity. We also compared the terminal performance of [l angle]100[r angle] and [l angle]111[r angle] single crystal tungsten with 90W-10 and 98W02 (NiFe) cemented tungsten and textured pure tungsten in laboratory scale ballistic experiments against monolithic 4340 alloy steel (HRC = 36) at normal impact. We radiographed the penetrators during the interactions with the targets, we recovered portions of the penetrators after the ballistic experiments, and we conducted metallographic examinations of penetrator remnants. From the radiographic records and the metallographic examinations, we drew conclusions pertaining to insights into the terminal interactions of the penetrators with the targets and suggestions as to improved compositions of the cemented tungsten penetrators.

  13. Interface adhesion between 2D materials and elastomers measured by buckle delamination

    NASA Astrophysics Data System (ADS)

    Brennan, Christopher; Lu, Nanshu

    2015-03-01

    A major application for 2D materials is creating electronic devices, including flexible and wearable devices. These applications require complicated fabrication processes where 2D materials are either mechanically exfoliated or grown via chemical vapor deposition and then transferred to a host substrate. Both processes require intimate knowledge of the interactions between the 2D material and the substrate to allow for a controllable transfer. Although adhesion between 2D materials and stiff substrates such as silicon and copper have been measured by bulge or peeling tests, adhesion between 2D materials and soft polymer substrates are hard to measure by conventional methods. Here we propose a simple way of measuring the adhesion between 2D materials and soft, stretchable elastomers using mature continuum mechanics equations. By creating buckle delamination in 2D atomic layers and measuring the buckle profile using an atomic force microscope, we can readily extract 2D-elastomer adhesion energy. Here we look at the adhesion of MoS2 and graphene to PDMS. The measured adhesion values are found insensitive to the applied strains in the substrate and are one order smaller than 2D-silicon oxide adhesion which is mainly attributed substrate surface roughness differences.

  14. Fabrication and properties of tungsten heavy metal alloys containing 30% to 90% tungsten

    SciTech Connect

    Gurwell, W.E.; Nelson, R.G.; Dudder, G.B.; Davis, N.C.

    1984-09-01

    In 1983, Pacific Northwest Laboratory conducted a survey of tungsten heavy metal alloys having lower-than-normal (<90%) tungsten content. The purpose of the work was to develop tougher, more impact-resistant high-density alloys for applications benefitting from improved mechanical properties. Tungsten heavy metal alloys of 30 to 90% tungsten content were fabricated and their mechanical properties measured. Although ultimate strength was essentially independent of tungsten content, lower tungsten-content alloys had lower yield stress, hardness, and density, and decidedly higher elongations and impact energies. Cold work was effective in raising strength and hardness but detrimental to elongation and impact energies. Precipitation hardening and strain aging raised hardness effectively but had less influence on other mechanical properties. 34 figures, 7 tables.

  15. Tungsten wire for incandescent lamps

    SciTech Connect

    Walter, J.L.; Briant, C.L. )

    1990-09-01

    Tungsten wire for incandescent lamp filaments must operate at high temperatures and for long times. To meet these requirements, the grain morphology of the wire must be controlled to reduce the propensity for grain boundary sliding. The morphology is a function of the distribution of very small pockets of potassium in the wire and the mechanical processing from ingot to wire. The behavior of the filament is directly related to the grain morphology. This paper describes the mechanism by which the potassium is incorporated into and distributed in the ingot. The elongation and spheroidization of the bubbles during hot rolling and swaging is also examined and related to the grain morphology of wire. Some indications of the relationship between grain morphology and filament behavior are also given.

  16. Dielectronic recombination of tungsten ions

    NASA Astrophysics Data System (ADS)

    Li, Bowen; O'Sullivan, Gerry; Dong, Chenzhong; Chen, Ximeng

    2016-08-01

    Ab initio calculations of dielectronic recombination rate coefficients of Ne-, Pd- and Ag-like tungsten have been performed. Energy levels, radiative transition probabilities and autoionization rates were calculated using the Flexible Atomic Code. The contributions from different channels to the total rate coefficients are discussed. The present calculated rate coefficients are compared with other calculations where available. Excellent agreement has been found for Ne-like W while a large discrepancy was found for Pd-like W, which implies that more ab initio calculations and experimental measurements are badly needed. Further calculations demonstrated that the influence of configuration interaction is small while nonresonant radiative stabilizing (NRS) contribution to doubly excited non-autoionizing states are vital. The data obtained are expected to be useful for modeling plasmas for fusion applications, especially for the ITER community, which makes experimental verification even more essential.

  17. High strength and density tungsten-uranium alloys

    DOEpatents

    Sheinberg, Haskell

    1993-01-01

    Alloys of tungsten and uranium and a method for making the alloys. The amount of tungsten present in the alloys is from about 55 vol % to about 85 vol %. A porous preform is made by sintering consolidated tungsten powder. The preform is impregnated with molten uranium such that (1) uranium fills the pores of the preform to form uranium in a tungsten matrix or (2) uranium dissolves portions of the preform to form a continuous uranium phase containing tungsten particles.

  18. 2D Quantum Transport Modeling in Nanoscale MOSFETs

    NASA Technical Reports Server (NTRS)

    Svizhenko, Alexei; Anantram, M. P.; Govindan, T. R.; Biegel, B.

    2001-01-01

    We have developed physical approximations and computer code capable of realistically simulating 2-D nanoscale transistors, using the non-equilibrium Green's function (NEGF) method. This is the most accurate full quantum model yet applied to 2-D device simulation. Open boundary conditions, oxide tunneling and phase-breaking scattering are treated on an equal footing. Electron bandstructure is treated within the anisotropic effective mass approximation. We present the results of our simulations of MIT 25 and 90 nm "well-tempered" MOSFETs and compare them to those of classical and quantum corrected models. The important feature of quantum model is smaller slope of Id-Vg curve and consequently higher threshold voltage. These results are consistent with 1D Schroedinger-Poisson calculations. The effect of gate length on gate-oxide leakage and subthreshold current has been studied. The shorter gate length device has an order of magnitude smaller leakage current than the longer gate length device without a significant trade-off in on-current.

  19. Stochastic Inversion of 2D Magnetotelluric Data

    SciTech Connect

    Chen, Jinsong

    2010-07-01

    The algorithm is developed to invert 2D magnetotelluric (MT) data based on sharp boundary parametrization using a Bayesian framework. Within the algorithm, we consider the locations and the resistivity of regions formed by the interfaces are as unknowns. We use a parallel, adaptive finite-element algorithm to forward simulate frequency-domain MT responses of 2D conductivity structure. Those unknown parameters are spatially correlated and are described by a geostatistical model. The joint posterior probability distribution function is explored by Markov Chain Monte Carlo (MCMC) sampling methods. The developed stochastic model is effective for estimating the interface locations and resistivity. Most importantly, it provides details uncertainty information on each unknown parameter. Hardware requirements: PC, Supercomputer, Multi-platform, Workstation; Software requirements C and Fortan; Operation Systems/version is Linux/Unix or Windows

  20. Explicit 2-D Hydrodynamic FEM Program

    1996-08-07

    DYNA2D* is a vectorized, explicit, two-dimensional, axisymmetric and plane strain finite element program for analyzing the large deformation dynamic and hydrodynamic response of inelastic solids. DYNA2D* contains 13 material models and 9 equations of state (EOS) to cover a wide range of material behavior. The material models implemented in all machine versions are: elastic, orthotropic elastic, kinematic/isotropic elastic plasticity, thermoelastoplastic, soil and crushable foam, linear viscoelastic, rubber, high explosive burn, isotropic elastic-plastic, temperature-dependent elastic-plastic. Themore » isotropic and temperature-dependent elastic-plastic models determine only the deviatoric stresses. Pressure is determined by one of 9 equations of state including linear polynomial, JWL high explosive, Sack Tuesday high explosive, Gruneisen, ratio of polynomials, linear polynomial with energy deposition, ignition and growth of reaction in HE, tabulated compaction, and tabulated.« less

  1. Stochastic Inversion of 2D Magnetotelluric Data

    2010-07-01

    The algorithm is developed to invert 2D magnetotelluric (MT) data based on sharp boundary parametrization using a Bayesian framework. Within the algorithm, we consider the locations and the resistivity of regions formed by the interfaces are as unknowns. We use a parallel, adaptive finite-element algorithm to forward simulate frequency-domain MT responses of 2D conductivity structure. Those unknown parameters are spatially correlated and are described by a geostatistical model. The joint posterior probability distribution function ismore » explored by Markov Chain Monte Carlo (MCMC) sampling methods. The developed stochastic model is effective for estimating the interface locations and resistivity. Most importantly, it provides details uncertainty information on each unknown parameter. Hardware requirements: PC, Supercomputer, Multi-platform, Workstation; Software requirements C and Fortan; Operation Systems/version is Linux/Unix or Windows« less

  2. Static & Dynamic Response of 2D Solids

    1996-07-15

    NIKE2D is an implicit finite-element code for analyzing the finite deformation, static and dynamic response of two-dimensional, axisymmetric, plane strain, and plane stress solids. The code is fully vectorized and available on several computing platforms. A number of material models are incorporated to simulate a wide range of material behavior including elasto-placicity, anisotropy, creep, thermal effects, and rate dependence. Slideline algorithms model gaps and sliding along material interfaces, including interface friction, penetration and single surfacemore » contact. Interactive-graphics and rezoning is included for analyses with large mesh distortions. In addition to quasi-Newton and arc-length procedures, adaptive algorithms can be defined to solve the implicit equations using the solution language ISLAND. Each of these capabilities and more make NIKE2D a robust analysis tool.« less

  3. Static & Dynamic Response of 2D Solids

    SciTech Connect

    Lin, Jerry

    1996-07-15

    NIKE2D is an implicit finite-element code for analyzing the finite deformation, static and dynamic response of two-dimensional, axisymmetric, plane strain, and plane stress solids. The code is fully vectorized and available on several computing platforms. A number of material models are incorporated to simulate a wide range of material behavior including elasto-placicity, anisotropy, creep, thermal effects, and rate dependence. Slideline algorithms model gaps and sliding along material interfaces, including interface friction, penetration and single surface contact. Interactive-graphics and rezoning is included for analyses with large mesh distortions. In addition to quasi-Newton and arc-length procedures, adaptive algorithms can be defined to solve the implicit equations using the solution language ISLAND. Each of these capabilities and more make NIKE2D a robust analysis tool.

  4. Explicit 2-D Hydrodynamic FEM Program

    SciTech Connect

    Lin, Jerry

    1996-08-07

    DYNA2D* is a vectorized, explicit, two-dimensional, axisymmetric and plane strain finite element program for analyzing the large deformation dynamic and hydrodynamic response of inelastic solids. DYNA2D* contains 13 material models and 9 equations of state (EOS) to cover a wide range of material behavior. The material models implemented in all machine versions are: elastic, orthotropic elastic, kinematic/isotropic elastic plasticity, thermoelastoplastic, soil and crushable foam, linear viscoelastic, rubber, high explosive burn, isotropic elastic-plastic, temperature-dependent elastic-plastic. The isotropic and temperature-dependent elastic-plastic models determine only the deviatoric stresses. Pressure is determined by one of 9 equations of state including linear polynomial, JWL high explosive, Sack Tuesday high explosive, Gruneisen, ratio of polynomials, linear polynomial with energy deposition, ignition and growth of reaction in HE, tabulated compaction, and tabulated.

  5. 2D photonic-crystal optomechanical nanoresonator.

    PubMed

    Makles, K; Antoni, T; Kuhn, A G; Deléglise, S; Briant, T; Cohadon, P-F; Braive, R; Beaudoin, G; Pinard, L; Michel, C; Dolique, V; Flaminio, R; Cagnoli, G; Robert-Philip, I; Heidmann, A

    2015-01-15

    We present the optical optimization of an optomechanical device based on a suspended InP membrane patterned with a 2D near-wavelength grating (NWG) based on a 2D photonic-crystal geometry. We first identify by numerical simulation a set of geometrical parameters providing a reflectivity higher than 99.8% over a 50-nm span. We then study the limitations induced by the finite value of the optical waist and lateral size of the NWG pattern using different numerical approaches. The NWG grating, pierced in a suspended InP 265-nm thick membrane, is used to form a compact microcavity involving the suspended nanomembrane as an end mirror. The resulting cavity has a waist size smaller than 10 μm and a finesse in the 200 range. It is used to probe the Brownian motion of the mechanical modes of the nanomembrane. PMID:25679837

  6. Observation of two distinct negative trions in tungsten disulfide monolayers

    NASA Astrophysics Data System (ADS)

    Boulesbaa, Abdelaziz; Huang, Bing; Wang, Kai; Lin, Ming-Wei; Mahjouri-Samani, Masoud; Rouleau, Christopher; Xiao, Kai; Yoon, Mina; Sumpter, Bobby; Puretzky, Alexander; Geohegan, David

    2015-09-01

    Ultrafast pump-probe spectroscopy of two-dimensional tungsten disulfide monolayers (2 D W S2) grown on sapphire substrates revealed two transient absorption spectral peaks that are attributed to distinct negative trions at ˜2.02 eV (T1) and ˜1.98 eV (T2) . The dynamics measurements indicate that trion formation by the probe is enabled by photodoped 2D WS2 crystals with electrons remaining after trapping of holes from excitons or free electron-hole pairs at defect sites in the crystal or on the substrate. Dynamics of the characteristic absorption bands of excitons XA and XB at ˜2.03 and ˜2.40 eV , respectively, were separately monitored and compared to the photoinduced absorption features. Selective excitation of the lowest exciton level XA using λpump<2.4 eV forms only trion T1, implying that the electron remaining from dissociation of exciton XA is involved in the creation of this trion with a binding energy ˜10 meV with respect to XA. The absorption peak corresponding to trion T2 appears when λpump<2.4 eV , which is just sufficient to excite exciton XB. The dynamics of trion T2 formation are found to correlate with the disappearance of the bleach of the XB exciton, indicating the involvement of holes participating in the bleach dynamics of exciton XB. Static electrical-doping photoabsorption measurements confirm the presence of an induced absorption peak similar to that of T2. Since the proposed trion formation process here involves exciton dissociation through hole trapping by defects in the 2D crystal or substrate, this discovery highlights the strong role of defects in defining optical and electrical properties of 2D metal chalcogenides, which is relevant to a broad spectrum of basic science and technological applications.

  7. Compact 2-D graphical representation of DNA

    NASA Astrophysics Data System (ADS)

    Randić, Milan; Vračko, Marjan; Zupan, Jure; Novič, Marjana

    2003-05-01

    We present a novel 2-D graphical representation for DNA sequences which has an important advantage over the existing graphical representations of DNA in being very compact. It is based on: (1) use of binary labels for the four nucleic acid bases, and (2) use of the 'worm' curve as template on which binary codes are placed. The approach is illustrated on DNA sequences of the first exon of human β-globin and gorilla β-globin.

  8. 2D materials: Graphene and others

    NASA Astrophysics Data System (ADS)

    Bansal, Suneev Anil; Singh, Amrinder Pal; Kumar, Suresh

    2016-05-01

    Present report reviews the recent advancements in new atomically thick 2D materials. Materials covered in this review are Graphene, Silicene, Germanene, Boron Nitride (BN) and Transition metal chalcogenides (TMC). These materials show extraordinary mechanical, electronic and optical properties which make them suitable candidates for future applications. Apart from unique properties, tune-ability of highly desirable properties of these materials is also an important area to be emphasized on.

  9. Layer Engineering of 2D Semiconductor Junctions.

    PubMed

    He, Yongmin; Sobhani, Ali; Lei, Sidong; Zhang, Zhuhua; Gong, Yongji; Jin, Zehua; Zhou, Wu; Yang, Yingchao; Zhang, Yuan; Wang, Xifan; Yakobson, Boris; Vajtai, Robert; Halas, Naomi J; Li, Bo; Xie, Erqing; Ajayan, Pulickel

    2016-07-01

    A new concept for junction fabrication by connecting multiple regions with varying layer thicknesses, based on the thickness dependence, is demonstrated. This type of junction is only possible in super-thin-layered 2D materials, and exhibits similar characteristics as p-n junctions. Rectification and photovoltaic effects are observed in chemically homogeneous MoSe2 junctions between domains of different thicknesses. PMID:27136275

  10. Realistic and efficient 2D crack simulation

    NASA Astrophysics Data System (ADS)

    Yadegar, Jacob; Liu, Xiaoqing; Singh, Abhishek

    2010-04-01

    Although numerical algorithms for 2D crack simulation have been studied in Modeling and Simulation (M&S) and computer graphics for decades, realism and computational efficiency are still major challenges. In this paper, we introduce a high-fidelity, scalable, adaptive and efficient/runtime 2D crack/fracture simulation system by applying the mathematically elegant Peano-Cesaro triangular meshing/remeshing technique to model the generation of shards/fragments. The recursive fractal sweep associated with the Peano-Cesaro triangulation provides efficient local multi-resolution refinement to any level-of-detail. The generated binary decomposition tree also provides efficient neighbor retrieval mechanism used for mesh element splitting and merging with minimal memory requirements essential for realistic 2D fragment formation. Upon load impact/contact/penetration, a number of factors including impact angle, impact energy, and material properties are all taken into account to produce the criteria of crack initialization, propagation, and termination leading to realistic fractal-like rubble/fragments formation. The aforementioned parameters are used as variables of probabilistic models of cracks/shards formation, making the proposed solution highly adaptive by allowing machine learning mechanisms learn the optimal values for the variables/parameters based on prior benchmark data generated by off-line physics based simulation solutions that produce accurate fractures/shards though at highly non-real time paste. Crack/fracture simulation has been conducted on various load impacts with different initial locations at various impulse scales. The simulation results demonstrate that the proposed system has the capability to realistically and efficiently simulate 2D crack phenomena (such as window shattering and shards generation) with diverse potentials in military and civil M&S applications such as training and mission planning.

  11. Molecular basis of carcinogenicity of tungsten alloy particles

    SciTech Connect

    Harris, Robert M.; Williams, Tim D.; Waring, Rosemary H.; Hodges, Nikolas J.

    2015-03-15

    The tungsten alloy of 91% tungsten, 6% nickel and 3% cobalt (WNC 91–6–3) induces rhabdomyosarcoma when implanted into a rat thigh muscle. To investigate whether this effect is species-specific human HSkMc primary muscle cells were exposed to WNC 91–6–3 particles and responses were compared with those from a rat skeletal muscle cell line (L6-C11). Toxicity was assessed by the adenylate kinase assay and microscopy, DNA damage by the Comet assay. Caspase 3 enzyme activity was measured and oligonucleotide microarrays were used for transcriptional profiling. WNC 91–6–3 particles caused toxicity in cells adjacent to the particles and also increased DNA strand breaks. Inhibition of caspase 3 by WNC 91–6–3 occurred in rat but not in human cells. In both rat and human cells, the transcriptional response to WNC 91–6–3 showed repression of transcripts encoding muscle-specific proteins with induction of glycolysis, hypoxia, stress responses and transcripts associated with DNA damage and cell death. In human cells, genes encoding metallothioneins were also induced, together with genes related to angiogenesis, dysregulation of apoptosis and proliferation consistent with pre-neoplastic changes. An alloy containing iron, WNF 97–2–1, which is non-carcinogenic in vivo in rats, did not show these transcriptional changes in vitro in either species while the corresponding cobalt-containing alloy, WNC 97–2–1 elicited similar responses to WNC 91–6–3. Tungsten alloys containing both nickel and cobalt therefore have the potential to be carcinogenic in man and in vitro assays coupled with transcriptomics can be used to identify alloys, which may lead to tumour formation, by dysregulation of biochemical processes. - Highlights: • Use of transcriptomics to identify likely carcinogenic tungsten alloys in vitro • Cobalt containing alloys cause oxidative stress, DNA-damage and perturb apoptosis. • Presence of cobalt causes changes in gene expression

  12. 2D Spinodal Decomposition in Forced Turbulence

    NASA Astrophysics Data System (ADS)

    Fan, Xiang; Diamond, Patrick; Chacon, Luis; Li, Hui

    2015-11-01

    Spinodal decomposition is a second order phase transition for binary fluid mixture, from one thermodynamic phase to form two coexisting phases. The governing equation for this coarsening process below critical temperature, Cahn-Hilliard Equation, is very similar to 2D MHD Equation, especially the conserved quantities have a close correspondence between each other, so theories for MHD turbulence are used to study spinodal decomposition in forced turbulence. Domain size is increased with time along with the inverse cascade, and the length scale can be arrested by a forced turbulence with direct cascade. The two competing mechanisms lead to a stabilized domain size length scale, which can be characterized by Hinze Scale. The 2D spinodal decomposition in forced turbulence is studied by both theory and simulation with ``pixie2d.'' This work focuses on the relation between Hinze scale and spectra and cascades. Similarities and differences between spinodal decomposition and MHD are investigated. Also some transport properties are studied following MHD theories. This work is supported by the Department of Energy under Award Number DE-FG02-04ER54738.

  13. MAGNUM-2D computer code: user's guide

    SciTech Connect

    England, R.L.; Kline, N.W.; Ekblad, K.J.; Baca, R.G.

    1985-01-01

    Information relevant to the general use of the MAGNUM-2D computer code is presented. This computer code was developed for the purpose of modeling (i.e., simulating) the thermal and hydraulic conditions in the vicinity of a waste package emplaced in a deep geologic repository. The MAGNUM-2D computer computes (1) the temperature field surrounding the waste package as a function of the heat generation rate of the nuclear waste and thermal properties of the basalt and (2) the hydraulic head distribution and associated groundwater flow fields as a function of the temperature gradients and hydraulic properties of the basalt. MAGNUM-2D is a two-dimensional numerical model for transient or steady-state analysis of coupled heat transfer and groundwater flow in a fractured porous medium. The governing equations consist of a set of coupled, quasi-linear partial differential equations that are solved using a Galerkin finite-element technique. A Newton-Raphson algorithm is embedded in the Galerkin functional to formulate the problem in terms of the incremental changes in the dependent variables. Both triangular and quadrilateral finite elements are used to represent the continuum portions of the spatial domain. Line elements may be used to represent discrete conduits. 18 refs., 4 figs., 1 tab.

  14. Engineering light outcoupling in 2D materials.

    PubMed

    Lien, Der-Hsien; Kang, Jeong Seuk; Amani, Matin; Chen, Kevin; Tosun, Mahmut; Wang, Hsin-Ping; Roy, Tania; Eggleston, Michael S; Wu, Ming C; Dubey, Madan; Lee, Si-Chen; He, Jr-Hau; Javey, Ali

    2015-02-11

    When light is incident on 2D transition metal dichalcogenides (TMDCs), it engages in multiple reflections within underlying substrates, producing interferences that lead to enhancement or attenuation of the incoming and outgoing strength of light. Here, we report a simple method to engineer the light outcoupling in semiconducting TMDCs by modulating their dielectric surroundings. We show that by modulating the thicknesses of underlying substrates and capping layers, the interference caused by substrate can significantly enhance the light absorption and emission of WSe2, resulting in a ∼11 times increase in Raman signal and a ∼30 times increase in the photoluminescence (PL) intensity of WSe2. On the basis of the interference model, we also propose a strategy to control the photonic and optoelectronic properties of thin-layer WSe2. This work demonstrates the utilization of outcoupling engineering in 2D materials and offers a new route toward the realization of novel optoelectronic devices, such as 2D LEDs and solar cells.

  15. Hollow cathodes with BaO impregnated, porous tungsten inserts and tips

    NASA Technical Reports Server (NTRS)

    Hudson, W. R.; Weigand, A. J.

    1973-01-01

    The technology of impregnated materials is described and some inherently advantageous characteristics of impregnated cathodes are discussed. Thermionic emission measurements are presented for oxide coated and impregnated cathodes. Five cathode configurations with barium oxide impregnated porous tungsten inserts and/or tips have been fabricated and tested. Reliability, durability, and stability of operation are characterized. One of the cathodes has accumulated over 9000 operational hours, another has been cycled on and off more than 800 times.

  16. Molybdenum and tungsten oxygen transferases--and functional diversity within a common active site motif.

    PubMed

    Pushie, M Jake; Cotelesage, Julien J; George, Graham N

    2014-01-01

    Molybdenum and tungsten are the only second and third-row transition elements with a known function in living organisms. The molybdenum and tungsten enzymes show common structural features, with the metal being bound by a pyranopterin-dithiolene cofactor called molybdopterin. They catalyze a variety of oxygen transferase reactions coupled with two-electron redox chemistry in which the metal cycles between the +6 and +4 oxidation states usually with water, either product or substrate, providing the oxygen. The functional roles filled by the molybdenum and tungsten enzymes are diverse; for example, they play essential roles in microbial respiration, in the uptake of nitrogen in green plants, and in human health. Together, the enzymes form a superfamily which is among the most prevalent known, being found in all kingdoms of life. This review discusses what is known of the active site structures and the mechanisms, together with some recent insights into the evolution of these important enzyme systems.

  17. Tungsten carbide nanoparticles as efficient cocatalysts for photocatalytic overall water splitting.

    PubMed

    Garcia-Esparza, Angel T; Cha, Dongkyu; Ou, Yiwei; Kubota, Jun; Domen, Kazunari; Takanabe, Kazuhiro

    2013-01-01

    Tungsten carbide exhibits platinum-like behavior, which makes it an interesting potential substitute for noble metals in catalytic applications. Tungsten carbide nanocrystals (≈5 nm) are directly synthesized through the reaction of tungsten precursors with mesoporous graphitic C(3)N(4) (mpg-C(3)N(4)) as the reactive template in a flow of inert gas at high temperatures. Systematic experiments that vary the precursor compositions and temperatures used in the synthesis selectively generate different compositions and structures for the final nanocarbide (W(2)C or WC) products. Electrochemical measurements demonstrate that the WC phase with a high surface area exhibits both high activity and stability in hydrogen evolution over a wide pH range. The WC sample also shows excellent hydrogen oxidation activity, whereas its activity in oxygen reduction is poor. These tungsten carbides are successful cocatalysts for overall water splitting and give H(2) and O(2) in a stoichiometric ratio from H(2)O decomposition when supported on a Na-doped SrTiO(3) photocatalyst. Herein, we present tungsten carbide (on a small scale) as a promising and durable catalyst substitute for platinum and other scarce noble-metal catalysts in catalytic reaction systems used for renewable energy generation. PMID:23255471

  18. International strategic mineral issues summary report: tungsten

    USGS Publications Warehouse

    Werner, Antony B.T.; Sinclair, W. David; Amey, Earle B.

    1998-01-01

    In 1995, China and the former Soviet Union accounted for over three-fourths of the world's mine production of tungsten. China alone produced about two-thirds of world output. Given its vast resources, China will likely maintain its prominent role in world tungsten supply. By the year 2020, changes in supply patterns are likely to result from declining output from individual deposits in Australia, Austria, and Portugal and the opening of new mines in Canada, China, and the United Kingdom.

  19. Optical Stark effect in 2D semiconductors

    NASA Astrophysics Data System (ADS)

    Sie, Edbert J.; McIver, James W.; Lee, Yi-Hsien; Fu, Liang; Kong, Jing; Gedik, Nuh

    2016-05-01

    Semiconductors that are atomically thin can exhibit novel optical properties beyond those encountered in the bulk compounds. Monolayer transition-metal dichalcogenides (TMDs) are leading examples of such semiconductors that possess remarkable optical properties. They obey unique selection rules where light with different circular polarization can be used for selective photoexcitation at two different valleys in the momentum space. These valleys constitute bandgaps that are normally locked in the same energy. Selectively varying their energies is of great interest for applications because it unlocks the potential to control valley degree of freedom, and offers a new promising way to carry information in next-generation valleytronics. In this proceeding paper, we show that the energy gaps at the two valleys can be shifted relative to each other by means of the optical Stark effect in a controllable valley-selective manner. We discuss the physics of the optical Stark effect, and we describe the mechanism that leads to its valleyselectivity in monolayer TMD tungsten disulfide (WS2).

  20. GBL-2D Version 1.0: a 2D geometry boolean library.

    SciTech Connect

    McBride, Cory L. (Elemental Technologies, American Fort, UT); Schmidt, Rodney Cannon; Yarberry, Victor R.; Meyers, Ray J.

    2006-11-01

    This report describes version 1.0 of GBL-2D, a geometric Boolean library for 2D objects. The library is written in C++ and consists of a set of classes and routines. The classes primarily represent geometric data and relationships. Classes are provided for 2D points, lines, arcs, edge uses, loops, surfaces and mask sets. The routines contain algorithms for geometric Boolean operations and utility functions. Routines are provided that incorporate the Boolean operations: Union(OR), XOR, Intersection and Difference. A variety of additional analytical geometry routines and routines for importing and exporting the data in various file formats are also provided. The GBL-2D library was originally developed as a geometric modeling engine for use with a separate software tool, called SummitView [1], that manipulates the 2D mask sets created by designers of Micro-Electro-Mechanical Systems (MEMS). However, many other practical applications for this type of software can be envisioned because the need to perform 2D Boolean operations can arise in many contexts.

  1. Tungsten targets the tumor microenvironment to enhance breast cancer metastasis.

    PubMed

    Bolt, Alicia M; Sabourin, Valérie; Molina, Manuel Flores; Police, Alice M; Negro Silva, Luis Fernando; Plourde, Dany; Lemaire, Maryse; Ursini-Siegel, Josie; Mann, Koren K

    2015-01-01

    The number of individuals exposed to high levels of tungsten is increasing, yet there is limited knowledge of the potential human health risks. Recently, a cohort of breast cancer patients was left with tungsten in their breasts following testing of a tungsten-based shield during intraoperative radiotherapy. While monitoring tungsten levels in the blood and urine of these patients, we utilized the 66Cl4 cell model, in vitro and in mice to study the effects of tungsten exposure on mammary tumor growth and metastasis. We still detect tungsten in the urine of patients' years after surgery (mean urinary tungsten concentration at least 20 months post-surgery = 1.76 ng/ml), even in those who have opted for mastectomy, indicating that tungsten does not remain in the breast. In addition, standard chelation therapy was ineffective at mobilizing tungsten. In the mouse model, tungsten slightly delayed primary tumor growth, but significantly enhanced lung metastasis. In vitro, tungsten did not enhance 66Cl4 proliferation or invasion, suggesting that tungsten was not directly acting on 66Cl4 primary tumor cells to enhance invasion. In contrast, tungsten changed the tumor microenvironment, enhancing parameters known to be important for cell invasion and metastasis including activated fibroblasts, matrix metalloproteinases, and myeloid-derived suppressor cells. We show, for the first time, that tungsten enhances metastasis in an animal model of breast cancer by targeting the microenvironment. Importantly, all these tumor microenvironmental changes are associated with a poor prognosis in humans. PMID:25324207

  2. Tungsten Targets the Tumor Microenvironment to Enhance Breast Cancer Metastasis

    PubMed Central

    Bolt, Alicia M.; Sabourin, Valérie; Molina, Manuel Flores; Police, Alice M.; Negro Silva, Luis Fernando; Plourde, Dany; Lemaire, Maryse; Ursini-Siegel, Josie; Mann, Koren K.

    2015-01-01

    The number of individuals exposed to high levels of tungsten is increasing, yet there is limited knowledge of the potential human health risks. Recently, a cohort of breast cancer patients was left with tungsten in their breasts following testing of a tungsten-based shield during intraoperative radiotherapy. While monitoring tungsten levels in the blood and urine of these patients, we utilized the 66Cl4 cell model, in vitro and in mice to study the effects of tungsten exposure on mammary tumor growth and metastasis. We still detect tungsten in the urine of patients’ years after surgery (mean urinary tungsten concentration at least 20 months post-surgery = 1.76 ng/ml), even in those who have opted for mastectomy, indicating that tungsten does not remain in the breast. In addition, standard chelation therapy was ineffective at mobilizing tungsten. In the mouse model, tungsten slightly delayed primary tumor growth, but significantly enhanced lung metastasis. In vitro, tungsten did not enhance 66Cl4 proliferation or invasion, suggesting that tungsten was not directly acting on 66Cl4 primary tumor cells to enhance invasion. In contrast, tungsten changed the tumor microenvironment, enhancing parameters known to be important for cell invasion and metastasis including activated fibroblasts, matrix metalloproteinases, and myeloid-derived suppressor cells. We show, for the first time, that tungsten enhances metastasis in an animal model of breast cancer by targeting the microenvironment. Importantly, all these tumor microenvironmental changes are associated with a poor prognosis in humans. PMID:25324207

  3. Tungsten targets the tumor microenvironment to enhance breast cancer metastasis.

    PubMed

    Bolt, Alicia M; Sabourin, Valérie; Molina, Manuel Flores; Police, Alice M; Negro Silva, Luis Fernando; Plourde, Dany; Lemaire, Maryse; Ursini-Siegel, Josie; Mann, Koren K

    2015-01-01

    The number of individuals exposed to high levels of tungsten is increasing, yet there is limited knowledge of the potential human health risks. Recently, a cohort of breast cancer patients was left with tungsten in their breasts following testing of a tungsten-based shield during intraoperative radiotherapy. While monitoring tungsten levels in the blood and urine of these patients, we utilized the 66Cl4 cell model, in vitro and in mice to study the effects of tungsten exposure on mammary tumor growth and metastasis. We still detect tungsten in the urine of patients' years after surgery (mean urinary tungsten concentration at least 20 months post-surgery = 1.76 ng/ml), even in those who have opted for mastectomy, indicating that tungsten does not remain in the breast. In addition, standard chelation therapy was ineffective at mobilizing tungsten. In the mouse model, tungsten slightly delayed primary tumor growth, but significantly enhanced lung metastasis. In vitro, tungsten did not enhance 66Cl4 proliferation or invasion, suggesting that tungsten was not directly acting on 66Cl4 primary tumor cells to enhance invasion. In contrast, tungsten changed the tumor microenvironment, enhancing parameters known to be important for cell invasion and metastasis including activated fibroblasts, matrix metalloproteinases, and myeloid-derived suppressor cells. We show, for the first time, that tungsten enhances metastasis in an animal model of breast cancer by targeting the microenvironment. Importantly, all these tumor microenvironmental changes are associated with a poor prognosis in humans.

  4. Tungsten Carbide-Cobalt with Nano-Crystalline Tungsten Carbide Platelets ---Synthesis, Processing, Sintering and Properties

    NASA Astrophysics Data System (ADS)

    Zhong, Yang

    Tungsten Carbide --- Cobalt (WC-Co) is one of the most important ceramic-metal composites, which has been used in variety areas of different industries. Future applications of WC-Co in more areas of industries require higher hardness and fracture toughness. Current technology of synthesis, processing and sintering of WC-Co barely enhances the hardness and fracture toughness of WC-Co simultaneously (including nanostructured WC-Co). Within this project, a new approach of effectively controlling the structure of WC to lead to the simultaneous enhancement of hardness and fracture toughness has been investigated. The nano-WC platelet is proposed to be promising for the simultaneous enhancement. Several different aspects related to the formation of nano-WC platelets are studied. A new and effective method to produce nanostructured WC-Co powder is established in this study. This method is a combination of high energy milling and carbothermic reduction of the mixture of tungsten oxide (WO 3) and cobalt oxide (Co3O4). The condition to remove the free carbon without decarburization of WC has been achieved by thermodynamic analysis and coupled experiments. By the utilization of density functional theory simulations and Wulff construction, the equilibrium shape of WC crystals inside WC-Co is predicted to be bulky structure instead of platelet structure. The growth mechanisms for the WC in commercial coarse grained WC-Co under different heating conditions are observed. It is found that the heating temperature is a critical factor affecting the structure of WC inside WC-Co. Higher temperature will lead to the layer-by-layer structure formation due to higher thermodynamic driving force. The in situ formation of nano-WC platelet is achieved using different W containing sources. The formation mechanism has been studied. Bulk WC-Co samples with nano-WC platelets are obtained through sintering of WC-Co nano-powder at relatively low sintering temperatures. The mechanical properties of

  5. Periodically sheared 2D Yukawa systems

    SciTech Connect

    Kovács, Anikó Zsuzsa; Hartmann, Peter; Donkó, Zoltán

    2015-10-15

    We present non-equilibrium molecular dynamics simulation studies on the dynamic (complex) shear viscosity of a 2D Yukawa system. We have identified a non-monotonic frequency dependence of the viscosity at high frequencies and shear rates, an energy absorption maximum (local resonance) at the Einstein frequency of the system at medium shear rates, an enhanced collective wave activity, when the excitation is near the plateau frequency of the longitudinal wave dispersion, and the emergence of significant configurational anisotropy at small frequencies and high shear rates.

  6. ENERGY LANDSCAPE OF 2D FLUID FORMS

    SciTech Connect

    Y. JIANG; ET AL

    2000-04-01

    The equilibrium states of 2D non-coarsening fluid foams, which consist of bubbles with fixed areas, correspond to local minima of the total perimeter. (1) The authors find an approximate value of the global minimum, and determine directly from an image how far a foam is from its ground state. (2) For (small) area disorder, small bubbles tend to sort inwards and large bubbles outwards. (3) Topological charges of the same sign repel while charges of opposite sign attract. (4) They discuss boundary conditions and the uniqueness of the pattern for fixed topology.

  7. WFR-2D: an analytical model for PWAS-generated 2D ultrasonic guided wave propagation

    NASA Astrophysics Data System (ADS)

    Shen, Yanfeng; Giurgiutiu, Victor

    2014-03-01

    This paper presents WaveFormRevealer 2-D (WFR-2D), an analytical predictive tool for the simulation of 2-D ultrasonic guided wave propagation and interaction with damage. The design of structural health monitoring (SHM) systems and self-aware smart structures requires the exploration of a wide range of parameters to achieve best detection and quantification of certain types of damage. Such need for parameter exploration on sensor dimension, location, guided wave characteristics (mode type, frequency, wavelength, etc.) can be best satisfied with analytical models which are fast and efficient. The analytical model was constructed based on the exact 2-D Lamb wave solution using Bessel and Hankel functions. Damage effects were inserted in the model by considering the damage as a secondary wave source with complex-valued directivity scattering coefficients containing both amplitude and phase information from wave-damage interaction. The analytical procedure was coded with MATLAB, and a predictive simulation tool called WaveFormRevealer 2-D was developed. The wave-damage interaction coefficients (WDICs) were extracted from harmonic analysis of local finite element model (FEM) with artificial non-reflective boundaries (NRB). The WFR-2D analytical simulation results were compared and verified with full scale multiphysics finite element models and experiments with scanning laser vibrometer. First, Lamb wave propagation in a pristine aluminum plate was simulated with WFR-2D, compared with finite element results, and verified by experiments. Then, an inhomogeneity was machined into the plate to represent damage. Analytical modeling was carried out, and verified by finite element simulation and experiments. This paper finishes with conclusions and suggestions for future work.

  8. Microwave Assisted 2D Materials Exfoliation

    NASA Astrophysics Data System (ADS)

    Wang, Yanbin

    Two-dimensional materials have emerged as extremely important materials with applications ranging from energy and environmental science to electronics and biology. Here we report our discovery of a universal, ultrafast, green, solvo-thermal technology for producing excellent-quality, few-layered nanosheets in liquid phase from well-known 2D materials such as such hexagonal boron nitride (h-BN), graphite, and MoS2. We start by mixing the uniform bulk-layered material with a common organic solvent that matches its surface energy to reduce the van der Waals attractive interactions between the layers; next, the solutions are heated in a commercial microwave oven to overcome the energy barrier between bulk and few-layers states. We discovered the minutes-long rapid exfoliation process is highly temperature dependent, which requires precise thermal management to obtain high-quality inks. We hypothesize a possible mechanism of this proposed solvo-thermal process; our theory confirms the basis of this novel technique for exfoliation of high-quality, layered 2D materials by using an as yet unknown role of the solvent.

  9. Multienzyme Inkjet Printed 2D Arrays.

    PubMed

    Gdor, Efrat; Shemesh, Shay; Magdassi, Shlomo; Mandler, Daniel

    2015-08-19

    The use of printing to produce 2D arrays is well established, and should be relatively facile to adapt for the purpose of printing biomaterials; however, very few studies have been published using enzyme solutions as inks. Among the printing technologies, inkjet printing is highly suitable for printing biomaterials and specifically enzymes, as it offers many advantages. Formulation of the inkjet inks is relatively simple and can be adjusted to a variety of biomaterials, while providing nonharmful environment to the enzymes. Here we demonstrate the applicability of inkjet printing for patterning multiple enzymes in a predefined array in a very straightforward, noncontact method. Specifically, various arrays of the enzymes glucose oxidase (GOx), invertase (INV) and horseradish peroxidase (HP) were printed on aminated glass surfaces, followed by immobilization using glutardialdehyde after printing. Scanning electrochemical microscopy (SECM) was used for imaging the printed patterns and to ascertain the enzyme activity. The successful formation of 2D arrays consisting of enzymes was explored as a means of developing the first surface confined enzyme based logic gates. Principally, XOR and AND gates, each consisting of two enzymes as the Boolean operators, were assembled, and their operation was studied by SECM. PMID:26214072

  10. 2-D or not 2-D, that is the question: A Northern California test

    SciTech Connect

    Mayeda, K; Malagnini, L; Phillips, W S; Walter, W R; Dreger, D

    2005-06-06

    Reliable estimates of the seismic source spectrum are necessary for accurate magnitude, yield, and energy estimation. In particular, how seismic radiated energy scales with increasing earthquake size has been the focus of recent debate within the community and has direct implications on earthquake source physics studies as well as hazard mitigation. The 1-D coda methodology of Mayeda et al. has provided the lowest variance estimate of the source spectrum when compared against traditional approaches that use direct S-waves, thus making it ideal for networks that have sparse station distribution. The 1-D coda methodology has been mostly confined to regions of approximately uniform complexity. For larger, more geophysically complicated regions, 2-D path corrections may be required. The complicated tectonics of the northern California region coupled with high quality broadband seismic data provides for an ideal ''apples-to-apples'' test of 1-D and 2-D path assumptions on direct waves and their coda. Using the same station and event distribution, we compared 1-D and 2-D path corrections and observed the following results: (1) 1-D coda results reduced the amplitude variance relative to direct S-waves by roughly a factor of 8 (800%); (2) Applying a 2-D correction to the coda resulted in up to 40% variance reduction from the 1-D coda results; (3) 2-D direct S-wave results, though better than 1-D direct waves, were significantly worse than the 1-D coda. We found that coda-based moment-rate source spectra derived from the 2-D approach were essentially identical to those from the 1-D approach for frequencies less than {approx}0.7-Hz, however for the high frequencies (0.7{le} f {le} 8.0-Hz), the 2-D approach resulted in inter-station scatter that was generally 10-30% smaller. For complex regions where data are plentiful, a 2-D approach can significantly improve upon the simple 1-D assumption. In regions where only 1-D coda correction is available it is still preferable over 2

  11. Evaporites and strata-bound tungsten mineralization

    SciTech Connect

    Ririe, G.T. )

    1989-02-01

    Discoidal gypsum crystal cavities occur in quartzites that host varying amounts of strata-bound scheelite mineralization near Halls Creek in Western Australia. The host quartzites have been regionally metamorphosed to greenschist facies and are contained within a Middle Proterozoic sequence that includes pelites, mafic and felsic volcanics, and volcaniclastic rocks. Textural, fluid inclusion, and oxygen isotope data indicate that scheelite was present in the host quartzites prior to regional metamorphism. The presence of crystal cavities after gypsum in the quartzites implies an evaporitic origin for this sequence. The continental-sabkha playa basins of the Mojave Desert, California, are suggested to be possible modern analogs-e.g., Searles Lake, where the tungsten content is up to 70 ppm WO{sub 3} in brines and 118 ppm in muds, and exceeds the amount of tungsten in all known deposits in the United States. Metamorphism of a continental evaporitic sequence containing tungsten could produce an assemblage of rocks very similar to those reported from several stratabound tungsten deposits. Some of these, such as at Halls Creek, may be related to original accumulations of tungsten in nonmarine evaporitic environments.

  12. Surface morphologies of He-implanted tungsten

    NASA Astrophysics Data System (ADS)

    Bannister, M. E.; Meyer, F. W.; Hijazi, H.; Unocic, K. A.; Garrison, L. M.; Parish, C. M.

    2016-09-01

    Surface morphologies of tungsten surfaces, both polycrystalline and single-crystal [1 1 0], were investigated using SEM and FIB/SEM techniques after implantations at elevated surfaces temperatures (1200-1300 K) using well-characterized, mono-energetic He ion beams with a wide range of ion energies (218 eV-250 keV). Nanofuzz was observed on polycrystalline tungsten (PCW) following implantation of 100-keV He ions at a flux threshold of 0.9 × 1016 cm-2 s-1, but not following 200-keV implantations with similar fluxes. No nanofuzz formation was observed on single-crystal [1 1 0] tungsten (SCW), despite fluxes exceeding those demonstrated previously to produce nanofuzz on polycrystalline tungsten. Pre-damaging the single-crystal tungsten with implanted C impurity interstitials did not significantly affect the surface morphologies resulting from the high-flux He ion implantations. The main factor leading to the different observed surface structures for the pristine and C-implanted single-crystal W samples appeared to be the peak He ion flux characterizing the different exposures. It was speculated that nanofuzz formation was not observed for any SCW target exposures because of increased incubation fluences required for such targets.

  13. Method of making a cathode from tungsten and iridium powders using a strontium peroxide containing material as the impregnant

    SciTech Connect

    Branovich, L.E.; Freeman, G.L.; Smith, B.

    1988-11-25

    This invention relates in general to a method of making a long-life high-current-density cathode and in particular, to a method of making such a cathode from a mixture of tungsten and iridium powders using a strontium peroxide containing material as the impregnant. The general object of this invention is to provide an improved method of making a long life high current density cathode. A more specific object of the invention is to provide such a method in which lower temperatures can be used than were used in S.N. 204,327 for the impregnation of the tungsten-iridium billet. It has now been found that the aforementioned objects can be attained by a method that uses a strontium peroxide-containing material as the impregnant. More particularly, according to the invention, a suitable porous billet of tungsten, or tungsten-iridium, or tungsten-osmium or tungsten-rhodium is impregnated with a strontium peroxide containing material in a hydrogen atmosphere and slowly heated to above 215 C to decompose the strontium peroxide, SrO/sub 2/ to form strontium oxide, SrO, and oxygen, O/sub 2/.

  14. Femtosecond laser direct writing of large-area two-dimensional metallic photonic crystal structures on tungsten surfaces.

    PubMed

    Qiao, Hongzhen; Yang, Jianjun; Wang, Fei; Yang, Yang; Sun, Julong

    2015-10-01

    Metallic photonic crystals (MPCs) and metamaterials operating in the visible spectrum are required for high-temperature nanophotonics, but they are often difficult to construct. This study demonstrates a new approach to directly write two-dimensional (2D) MPCs on tungsten surfaces through the cylindrical focusing of two collinear femtosecond laser beams with certain temporal delays and orthogonal linear polarizations. Results are physically attributed to the laser-induced transient crossed temperature grating patterns and tempo-spatial thermal correlations. Optical properties of the fabricated MPCs are characterized. Such a simple and efficient technique can be used to fabricate large-area, 2D microstructures on metal surfaces for potential applications.

  15. 2D Quantum Transport Modeling in Nanoscale MOSFETs

    NASA Technical Reports Server (NTRS)

    Svizhenko, Alexei; Anantram, M. P.; Govindan, T. R.; Biegel, Bryan

    2001-01-01

    With the onset of quantum confinement in the inversion layer in nanoscale MOSFETs, behavior of the resonant level inevitably determines all device characteristics. While most classical device simulators take quantization into account in some simplified manner, the important details of electrostatics are missing. Our work addresses this shortcoming and provides: (a) a framework to quantitatively explore device physics issues such as the source-drain and gate leakage currents, DIBL, and threshold voltage shift due to quantization, and b) a means of benchmarking quantum corrections to semiclassical models (such as density- gradient and quantum-corrected MEDICI). We have developed physical approximations and computer code capable of realistically simulating 2-D nanoscale transistors, using the non-equilibrium Green's function (NEGF) method. This is the most accurate full quantum model yet applied to 2-D device simulation. Open boundary conditions, oxide tunneling and phase-breaking scattering are treated on equal footing. Electrons in the ellipsoids of the conduction band are treated within the anisotropic effective mass approximation. Quantum simulations are focused on MIT 25, 50 and 90 nm "well- tempered" MOSFETs and compared to classical and quantum corrected models. The important feature of quantum model is smaller slope of Id-Vg curve and consequently higher threshold voltage. These results are quantitatively consistent with I D Schroedinger-Poisson calculations. The effect of gate length on gate-oxide leakage and sub-threshold current has been studied. The shorter gate length device has an order of magnitude smaller current at zero gate bias than the longer gate length device without a significant trade-off in on-current. This should be a device design consideration.

  16. 2D Quantum Mechanical Study of Nanoscale MOSFETs

    NASA Technical Reports Server (NTRS)

    Svizhenko, Alexei; Anantram, M. P.; Govindan, T. R.; Biegel, B.; Kwak, Dochan (Technical Monitor)

    2000-01-01

    With the onset of quantum confinement in the inversion layer in nanoscale MOSFETs, behavior of the resonant level inevitably determines all device characteristics. While most classical device simulators take quantization into account in some simplified manner, the important details of electrostatics are missing. Our work addresses this shortcoming and provides: (a) a framework to quantitatively explore device physics issues such as the source-drain and gate leakage currents, DIBL, and threshold voltage shift due to quantization, and b) a means of benchmarking quantum corrections to semiclassical models (such as density-gradient and quantum-corrected MEDICI). We have developed physical approximations and computer code capable of realistically simulating 2-D nanoscale transistors, using the non-equilibrium Green's function (NEGF) method. This is the most accurate full quantum model yet applied to 2-D device simulation. Open boundary conditions and oxide tunneling are treated on an equal footing. Electrons in the ellipsoids of the conduction band are treated within the anisotropic effective mass approximation. We present the results of our simulations of MIT 25, 50 and 90 nm "well-tempered" MOSFETs and compare them to those of classical and quantum corrected models. The important feature of quantum model is smaller slope of Id-Vg curve and consequently higher threshold voltage. Surprisingly, the self-consistent potential profile shows lower injection barrier in the channel in quantum case. These results are qualitatively consistent with ID Schroedinger-Poisson calculations. The effect of gate length on gate-oxide leakage and subthreshold current has been studied. The shorter gate length device has an order of magnitude smaller current at zero gate bias than the longer gate length device without a significant trade-off in on-current. This should be a device design consideration.

  17. Canard configured aircraft with 2-D nozzle

    NASA Technical Reports Server (NTRS)

    Child, R. D.; Henderson, W. P.

    1978-01-01

    A closely-coupled canard fighter with vectorable two-dimensional nozzle was designed for enhanced transonic maneuvering. The HiMAT maneuver goal of a sustained 8g turn at a free-stream Mach number of 0.9 and 30,000 feet was the primary design consideration. The aerodynamic design process was initiated with a linear theory optimization minimizing the zero percent suction drag including jet effects and refined with three-dimensional nonlinear potential flow techniques. Allowances were made for mutual interference and viscous effects. The design process to arrive at the resultant configuration is described, and the design of a powered 2-D nozzle model to be tested in the LRC 16-foot Propulsion Wind Tunnel is shown.

  18. 2D Electrostatic Actuation of Microshutter Arrays

    NASA Technical Reports Server (NTRS)

    Burns, Devin E.; Oh, Lance H.; Li, Mary J.; Kelly, Daniel P.; Kutyrev, Alexander S.; Moseley, Samuel H.

    2015-01-01

    Electrostatically actuated microshutter arrays consisting of rotational microshutters (shutters that rotate about a torsion bar) were designed and fabricated through the use of models and experiments. Design iterations focused on minimizing the torsional stiffness of the microshutters, while maintaining their structural integrity. Mechanical and electromechanical test systems were constructed to measure the static and dynamic behavior of the microshutters. The torsional stiffness was reduced by a factor of four over initial designs without sacrificing durability. Analysis of the resonant behavior of the microshutters demonstrates that the first resonant mode is a torsional mode occurring around 3000 Hz. At low vacuum pressures, this resonant mode can be used to significantly reduce the drive voltage necessary for actuation requiring as little as 25V. 2D electrostatic latching and addressing was demonstrated using both a resonant and pulsed addressing scheme.

  19. 2D Electrostatic Actuation of Microshutter Arrays

    NASA Technical Reports Server (NTRS)

    Burns, Devin E.; Oh, Lance H.; Li, Mary J.; Jones, Justin S.; Kelly, Daniel P.; Zheng, Yun; Kutyrev, Alexander S.; Moseley, Samuel H.

    2015-01-01

    An electrostatically actuated microshutter array consisting of rotational microshutters (shutters that rotate about a torsion bar) were designed and fabricated through the use of models and experiments. Design iterations focused on minimizing the torsional stiffness of the microshutters, while maintaining their structural integrity. Mechanical and electromechanical test systems were constructed to measure the static and dynamic behavior of the microshutters. The torsional stiffness was reduced by a factor of four over initial designs without sacrificing durability. Analysis of the resonant behavior of the microshutter arrays demonstrates that the first resonant mode is a torsional mode occurring around 3000 Hz. At low vacuum pressures, this resonant mode can be used to significantly reduce the drive voltage necessary for actuation requiring as little as 25V. 2D electrostatic latching and addressing was demonstrated using both a resonant and pulsed addressing scheme.

  20. 2D quantum gravity from quantum entanglement.

    PubMed

    Gliozzi, F

    2011-01-21

    In quantum systems with many degrees of freedom the replica method is a useful tool to study the entanglement of arbitrary spatial regions. We apply it in a way that allows them to backreact. As a consequence, they become dynamical subsystems whose position, form, and extension are determined by their interaction with the whole system. We analyze, in particular, quantum spin chains described at criticality by a conformal field theory. Its coupling to the Gibbs' ensemble of all possible subsystems is relevant and drives the system into a new fixed point which is argued to be that of the 2D quantum gravity coupled to this system. Numerical experiments on the critical Ising model show that the new critical exponents agree with those predicted by the formula of Knizhnik, Polyakov, and Zamolodchikov.

  1. Graphene suspensions for 2D printing

    NASA Astrophysics Data System (ADS)

    Soots, R. A.; Yakimchuk, E. A.; Nebogatikova, N. A.; Kotin, I. A.; Antonova, I. V.

    2016-04-01

    It is shown that, by processing a graphite suspension in ethanol or water by ultrasound and centrifuging, it is possible to obtain particles with thicknesses within 1-6 nm and, in the most interesting cases, 1-1.5 nm. Analogous treatment of a graphite suspension in organic solvent yields eventually thicker particles (up to 6-10 nm thick) even upon long-term treatment. Using the proposed ink based on graphene and aqueous ethanol with ethylcellulose and terpineol additives for 2D printing, thin (~5 nm thick) films with sheet resistance upon annealing ~30 MΩ/□ were obtained. With the ink based on aqueous graphene suspension, the sheet resistance was ~5-12 kΩ/□ for 6- to 15-nm-thick layers with a carrier mobility of ~30-50 cm2/(V s).

  2. Microscopic and spectroscopic analysis of tungsten trioxide and titanium-doped tungsten trioxide thin films

    NASA Astrophysics Data System (ADS)

    Yun, Young Taek

    Tungsten oxide (WO3) has been a subject of high interest for its unique properties, and recently for its importance in different types of industrial applications which ranges from non-emissive displays, optical, microelectronic, catalytic/photocatalytic, humidity, temperature, gas, and biosensor devices. In this study, WO3 and Ti doped thin films were prepared using radio frequency magnetron reactive sputtering at different substrate temperatures ranging from room temperature to 500 °C in increments of 100 °C. After forming a hypothesis based on knowledge of established WO3 properties, we attempt in this work to investigate how the doping influences the roughness and the mean grain size of the nanoparticles on the surface layer of the thin films, its structure, and crystallinity. Therefore we pursued analysis by Atomic Force Microscopy (AFM), X-ray diffraction (XRD), and Raman spectroscopy, using a comparative approach. The outcomes of these analyses demonstrate that higher temperatures are necessary for growing crystalline material if doping is used. Also, smaller nanoparticles are obtained when a small amount of dopant, e.g. 5% Ti, is incorporated. Both XRD and Raman measurement indicate morphological changes of the doped material. Finally, annealing of the amorphous doped samples at temperatures of 600 °C and 900 °C did not contribute significantly to material properties improvement.

  3. Metrology for graphene and 2D materials

    NASA Astrophysics Data System (ADS)

    Pollard, Andrew J.

    2016-09-01

    The application of graphene, a one atom-thick honeycomb lattice of carbon atoms with superlative properties, such as electrical conductivity, thermal conductivity and strength, has already shown that it can be used to benefit metrology itself as a new quantum standard for resistance. However, there are many application areas where graphene and other 2D materials, such as molybdenum disulphide (MoS2) and hexagonal boron nitride (h-BN), may be disruptive, areas such as flexible electronics, nanocomposites, sensing and energy storage. Applying metrology to the area of graphene is now critical to enable the new, emerging global graphene commercial world and bridge the gap between academia and industry. Measurement capabilities and expertise in a wide range of scientific areas are required to address this challenge. The combined and complementary approach of varied characterisation methods for structural, chemical, electrical and other properties, will allow the real-world issues of commercialising graphene and other 2D materials to be addressed. Here, examples of metrology challenges that have been overcome through a multi-technique or new approach are discussed. Firstly, the structural characterisation of defects in both graphene and MoS2 via Raman spectroscopy is described, and how nanoscale mapping of vacancy defects in graphene is also possible using tip-enhanced Raman spectroscopy (TERS). Furthermore, the chemical characterisation and removal of polymer residue on chemical vapour deposition (CVD) grown graphene via secondary ion mass spectrometry (SIMS) is detailed, as well as the chemical characterisation of iron films used to grow large domain single-layer h-BN through CVD growth, revealing how contamination of the substrate itself plays a role in the resulting h-BN layer. In addition, the role of international standardisation in this area is described, outlining the current work ongoing in both the International Organization of Standardization (ISO) and the

  4. Pilot Study on the Detection of Simulated Lesions Using a 2D and 3D Digital Full-Field Mammography System with a Newly Developed High Resolution Detector Based on Two Shifts of a-Se.

    PubMed

    Schulz-Wendtland, R; Bani, M; Lux, M P; Schwab, S; Loehberg, C R; Jud, S M; Rauh, C; Bayer, C M; Beckmann, M W; Uder, M; Fasching, P A; Adamietz, B; Meier-Meitinger, M

    2012-05-01

    Purpose: Experimental study of a new system for digital 2D and 3D full-field mammography (FFDM) using a high resolution detector based on two shifts of a-Se. Material and Methods: Images were acquired using the new FFDM system Amulet® (FujiFilm, Tokio, Japan), an a-Se detector (receptor 24 × 30 cm(2), pixel size 50 µm, memory depth 12 bit, spatial resolution 10 lp/mm, DQE > 0.50). Integrated in the detector is a new method for data transfer, based on optical switch technology. The object of investigation was the Wisconsin Mammographic Random Phantom, Model 152A (Radiation Measurement Inc., Middleton, WI, USA) and the same parameters and exposure data (Tungsten, 100 mAs, 30 kV) were consistently used. We acquired 3 different pairs of images in the c-c and ml planes (2D) and in the c-c and c-c planes with an angle of 4 degrees (3D). Five radiologists experienced in mammography (experience ranging from 3 months to more than 5 years) analyzed the images (monitoring) which had been randomly encoded (random generator) with regard to the recognition of details such as specks of aluminum oxide (200-740 µm), nylon fibers (0.4-1.6 mm) and round lesions/masses (diameters 5-14 mm), using special linear glasses for 3D visualization, and compared the results. Results: A total of 225 correct positive decisions could be detected: we found 222 (98.7 %) correct positive results for 2D and 3D visualization in each case. Conclusion: The results of this phantom study showed the same detection rates for both 2D and 3D imaging using full field digital mammography. Our results must be confirmed in further clinical trials.

  5. Electroanalytical determination of tungsten and molybdenum in proteins.

    PubMed

    Hagedoorn, P L; van't Slot, P; van Leeuwen, H P; Hagen, W R

    2001-10-01

    Recent crystal structure determinations accelerated the progress in the biochemistry of tungsten-containing enzymes. In order to characterize these enzymes, a sensitive determination of this metal in protein-containing samples is necessary. An electroanalytical tungsten determination has successfully been adapted to determine the tungsten and molybdenum content in enzymes. The tungsten and molybdenum content can be measured simultaneously from 1 to 10 microg of purified protein with little or no sample handling. More crude protein samples require precipitation of interfering surface active material with 10% perchloric acid. This method affords the isolation of novel molybdenum- and tungsten-containing proteins via molybdenum and tungsten monitoring of column fractions, without using radioactive isotopes. A screening of soluble proteins from Pyrococcus furiosus for tungsten, using anion-exchange column chromatography to separate the proteins, has been performed. The three known tungsten-containing enzymes from P. furiosus were recovered with this screening.

  6. 2D-MoO3 nanosheets for superior gas sensors.

    PubMed

    Ji, Fangxu; Ren, Xianpei; Zheng, Xiaoyao; Liu, Yucheng; Pang, Liuqing; Jiang, Jiaxing; Liu, Shengzhong Frank

    2016-04-28

    By taking advantages of both grinding and sonication, an effective exfoliation process is developed to prepare two-dimensional (2D) molybdenum oxide (MoO3) nanosheets. The approach avoids high-boiling-point solvents that would leave a residue and cause aggregation. Gas sensors fabricated using the 2D-MoO3 nanosheets provide a significantly enhanced chemical sensor performance. Compared with the sensors using bulk MoO3, the response of the 2D-MoO3 sensor increases from 7 to 33; the sensor response time is reduced from 27 to 21 seconds, and the recovery time is shortened from 26 to 10 seconds. We attribute the superior performance to the 2D-structure with a much increased surface area and reactive sites. PMID:27053379

  7. CYP2D6*36 gene arrangements within the cyp2d6 locus: association of CYP2D6*36 with poor metabolizer status.

    PubMed

    Gaedigk, Andrea; Bradford, L Dianne; Alander, Sarah W; Leeder, J Steven

    2006-04-01

    Unexplained cases of CYP2D6 genotype/phenotype discordance continue to be discovered. In previous studies, several African Americans with a poor metabolizer phenotype carried the reduced function CYP2D6*10 allele in combination with a nonfunctional allele. We pursued the possibility that these alleles harbor either a known sequence variation (i.e., CYP2D6*36 carrying a gene conversion in exon 9 along the CYP2D6*10-defining 100C>T single-nucleotide polymorphism) or novel sequences variation(s). Discordant cases were evaluated by long-range polymerase chain reaction (PCR) to test for gene rearrangement events, and a 6.6-kilobase pair PCR product encompassing the CYP2D6 gene was cloned and entirely sequenced. Thereafter, allele frequencies were determined in different study populations comprising whites, African Americans, and Asians. Analyses covering the CYP2D7 to 2D6 gene region established that CYP2D6*36 did not only exist as a gene duplication (CYP2D6*36x2) or in tandem with *10 (CYP2D6*36+*10), as previously reported, but also by itself. This "single" CYP2D6*36 allele was found in nine African Americans and one Asian, but was absent in the whites tested. Ultimately, the presence of CYP2D6*36 resolved genotype/phenotype discordance in three cases. We also discovered an exon 9 conversion-positive CYP2D6*4 gene in a duplication arrangement (CYP2D6*4Nx2) and a CYP2D6*4 allele lacking 100C>T (CYP2D6*4M) in two white subjects. The discovery of an allele that carries only one CYP2D6*36 gene copy provides unequivocal evidence that both CYP2D6*36 and *36x2 are associated with a poor metabolizer phenotype. Given a combined frequency of between 0.5 and 3% in African Americans and Asians, genotyping for CYP2D6*36 should improve the accuracy of genotype-based phenotype prediction in these populations.

  8. Mechanical loading and the synthesis of 1,25(OH)2D in primary human osteoblasts.

    PubMed

    van der Meijden, K; Bakker, A D; van Essen, H W; Heijboer, A C; Schulten, E A J M; Lips, P; Bravenboer, N

    2016-02-01

    The metabolite 1,25-dihydroxyvitamin D (1,25(OH)2D) is synthesized from its precursor 25-hydroxyvitamin D (25(OH)D) by human osteoblasts leading to stimulation of osteoblast differentiation in an autocrine or paracrine way. Osteoblast differentiation is also stimulated by mechanical loading through activation of various responses in bone cells such as nitric oxide signaling. Whether mechanical loading affects osteoblast differentiation through an enhanced synthesis of 1,25(OH)2D by human osteoblasts is still unknown. We hypothesized that mechanical loading stimulates the synthesis of 1,25(OH)2D from 25(OH)D in primary human osteoblasts. Since the responsiveness of bone to mechanical stimuli can be altered by various endocrine factors, we also investigated whether 1,25(OH)2D or 25(OH)D affect the response of primary human osteoblasts to mechanical loading. Primary human osteoblasts were pre-incubated in medium with/without 25(OH)D3 (400 nM) or 1,25(OH)2D3 (100 nM) for 24h and subjected to mechanical loading by pulsatile fluid flow (PFF). The response of osteoblasts to PFF was quantified by measuring nitric oxide, and by PCR analysis. The effect of PFF on the synthesis of 1,25(OH)2D3 was determined by subjecting osteoblasts to PFF followed by 24h post-incubation in medium with/without 25(OH)D3 (400 nM). We showed that 1,25(OH)2D3 reduced the PFF-induced NO response in primary human osteoblasts. 25(OH)D3 did not significantly alter the NO response of primary human osteoblasts to PFF, but 25(OH)D3 increased osteocalcin and RANKL mRNA levels, similar to 1,25(OH)2D3. PFF did not increase 1,25(OH)2D3 amounts in our model, even though PFF did increase CYP27B1 mRNA levels and reduced VDR mRNA levels. CYP24 mRNA levels were not affected by PFF, but were strongly increased by both 25(OH)D3 and 1,25(OH)2D3. In conclusion, 1,25(OH)2D3 may affect the response of primary human osteoblasts to mechanical stimuli, at least with respect to NO production. Mechanical stimuli may affect

  9. Ablation study of tungsten-based nuclear thermal rocket fuel

    NASA Astrophysics Data System (ADS)

    Smith, Tabitha Elizabeth Rose

    The research described in this thesis has been performed in order to support the materials research and development efforts of NASA Marshall Space Flight Center (MSFC), of Tungsten-based Nuclear Thermal Rocket (NTR) fuel. The NTR was developed to a point of flight readiness nearly six decades ago and has been undergoing gradual modification and upgrading since then. Due to the simplicity in design of the NTR, and also in the modernization of the materials fabrication processes of nuclear fuel since the 1960's, the fuel of the NTR has been upgraded continuously. Tungsten-based fuel is of great interest to the NTR community, seeking to determine its advantages over the Carbide-based fuel of the previous NTR programs. The materials development and fabrication process contains failure testing, which is currently being conducted at MSFC in the form of heating the material externally and internally to replicate operation within the nuclear reactor of the NTR, such as with hot gas and RF coils. In order to expand on these efforts, experiments and computational studies of Tungsten and a Tungsten Zirconium Oxide sample provided by NASA have been conducted for this dissertation within a plasma arc-jet, meant to induce ablation on the material. Mathematical analysis was also conducted, for purposes of verifying experiments and making predictions. The computational method utilizes Anisimov's kinetic method of plasma ablation, including a thermal conduction parameter from the Chapman Enskog expansion of the Maxwell Boltzmann equations, and has been modified to include a tangential velocity component. Experimental data matches that of the computational data, in which plasma ablation at an angle shows nearly half the ablation of plasma ablation at no angle. Fuel failure analysis of two NASA samples post-testing was conducted, and suggestions have been made for future materials fabrication processes. These studies, including the computational kinetic model at an angle and the

  10. Chromatic instabilities in cesium-doped tungsten bronze nanoparticles

    SciTech Connect

    Adachi, Kenji Ota, Yosuke; Tanaka, Hiroyuki; Okada, Mika; Oshimura, Nobumitsu; Tofuku, Atsushi

    2013-11-21

    Nanoparticles of alkali-doped tungsten bronzes are an excellent near-infrared shielding material, but exhibit slight chromatic instabilities typically upon applications of strong ultra-violet light or heating in humid environment, which acts detrimentally to long-life commercial applications. Origin of the chromatic instabilities in cesium-doped tungsten bronze has been investigated, and it has been found that the coloration and bleaching processes comprised electronic exchanges which accelerate or depress the polaron excitation and the localized surface plasmon resonance. Coloration on UV illumination is evidenced by electron diffraction as due to the formation of H{sub x}WO{sub 3}, which is considered to take place in the surface Cs-deficient WO{sub 3} region via the double charge injection mechanism. On the other hand, bleaching on heating in air and in humid environment is shown to accompany the extraction of Cs and electrons from Cs{sub 0.33}WO{sub 3} by X-ray photoelectron spectroscopy and X-ray diffraction analysis and is concluded to be an oxidation of Cs{sub 0.33}WO{sub 3} on the particle surface.

  11. 2D-MoO3 nanosheets for superior gas sensors

    NASA Astrophysics Data System (ADS)

    Ji, Fangxu; Ren, Xianpei; Zheng, Xiaoyao; Liu, Yucheng; Pang, Liuqing; Jiang, Jiaxing; Liu, Shengzhong (Frank)

    2016-04-01

    By taking advantages of both grinding and sonication, an effective exfoliation process is developed to prepare two-dimensional (2D) molybdenum oxide (MoO3) nanosheets. The approach avoids high-boiling-point solvents that would leave a residue and cause aggregation. Gas sensors fabricated using the 2D-MoO3 nanosheets provide a significantly enhanced chemical sensor performance. Compared with the sensors using bulk MoO3, the response of the 2D-MoO3 sensor increases from 7 to 33; the sensor response time is reduced from 27 to 21 seconds, and the recovery time is shortened from 26 to 10 seconds. We attribute the superior performance to the 2D-structure with a much increased surface area and reactive sites.By taking advantages of both grinding and sonication, an effective exfoliation process is developed to prepare two-dimensional (2D) molybdenum oxide (MoO3) nanosheets. The approach avoids high-boiling-point solvents that would leave a residue and cause aggregation. Gas sensors fabricated using the 2D-MoO3 nanosheets provide a significantly enhanced chemical sensor performance. Compared with the sensors using bulk MoO3, the response of the 2D-MoO3 sensor increases from 7 to 33; the sensor response time is reduced from 27 to 21 seconds, and the recovery time is shortened from 26 to 10 seconds. We attribute the superior performance to the 2D-structure with a much increased surface area and reactive sites. Electronic supplementary information (ESI) available. See DOI: 10.1039/c6nr00880a

  12. Bioinspired 2D-Carbon Flakes and Fe3O4 Nanoparticles Composite for Arsenite Removal.

    PubMed

    Venkateswarlu, Sada; Lee, Daeho; Yoon, Minyoung

    2016-09-14

    Development of carbon-based materials has received tremendous attention owing to their multifunctional properties. Biomaterials often serve as an inspiration for the preparation of new carbon materials. Herein, we present a facile synthesis of a new bioinspired graphene oxide-like 2D-carbon flake (CF) using a natural resource, waste onion sheathing (Allium cepa). The 2D-CF was further decorated with crystalline Fe3O4 nanoparticles for applications. Superparamagnetic Fe3O4 nanoparticles (7 nm) were well-dispersed on the surface of the 2D-CF, which was characterized by X-ray diffractometry, X-ray photoelectron spectroscopy, Raman spectrometry, and transmission electron microscopy. Batch As(III) adsorption experiments showed that aqueous arsenic ions strongly adsorbed to the Fe3O4@2D-CF composite. The adsorption capacity of the Fe3O4@2D-CF composite for As(III) was 57.47 mg g(-1). The synergetic effect of both graphene oxide-like 2D-CF and Fe3O4 nanoparticles aided in excellent As(III) adsorption. An As(III) ion adsorption kinetics study showed that adsorption was very fast at the initial stage, and equilibrium was reached within 60 min following a pseudo-second-order rate model. Owing to the excellent superparamagnetic properties (52.6 emu g(-1)), the Fe3O4@2D-CF composite exhibited superb reusability with the shortest recovery time (28 s) among reported materials. This study indicated that Fe3O4@2D-CF composites can be used for practical applications as a global economic material for future generations. PMID:27463424

  13. A new inversion method for (T2, D) 2D NMR logging and fluid typing

    NASA Astrophysics Data System (ADS)

    Tan, Maojin; Zou, Youlong; Zhou, Cancan

    2013-02-01

    One-dimensional nuclear magnetic resonance (1D NMR) logging technology has some significant limitations in fluid typing. However, not only can two-dimensional nuclear magnetic resonance (2D NMR) provide some accurate porosity parameters, but it can also identify fluids more accurately than 1D NMR. In this paper, based on the relaxation mechanism of (T2, D) 2D NMR in a gradient magnetic field, a hybrid inversion method that combines least-squares-based QR decomposition (LSQR) and truncated singular value decomposition (TSVD) is examined in the 2D NMR inversion of various fluid models. The forward modeling and inversion tests are performed in detail with different acquisition parameters, such as magnetic field gradients (G) and echo spacing (TE) groups. The simulated results are discussed and described in detail, the influence of the above-mentioned observation parameters on the inversion accuracy is investigated and analyzed, and the observation parameters in multi-TE activation are optimized. Furthermore, the hybrid inversion can be applied to quantitatively determine the fluid saturation. To study the effects of noise level on the hybrid method and inversion results, the numerical simulation experiments are performed using different signal-to-noise-ratios (SNRs), and the effect of different SNRs on fluid typing using three fluid models are discussed and analyzed in detail.

  14. Ultra-broad band absorber made by tungsten and aluminium

    NASA Astrophysics Data System (ADS)

    Wang, Wei; Zhao, Ding; Li, Qiang; Qiu, Min

    2016-01-01

    A broadband absorber comprising tungsten cubic arrays, a alumina layer and a tungsten film, is numerically and experimentally investigated, which exhibits near-unity absorption of visible and near-infrared light from 400 nm to 1150 nm. Benefiting from high melting points of tungsten and alumina, this device has great application potential in solar cells and thermal emission.

  15. Raman scattering from rapid thermally annealed tungsten silicide

    NASA Technical Reports Server (NTRS)

    Kumar, Sandeep; Dasgupta, Samhita; Jackson, Howard E.; Boyd, Joseph T.

    1987-01-01

    Raman scattering as a technique for studying the formation of tungsten silicide is presented. The tungsten silicide films have been formed by rapid thermal annealing of thin tungsten films sputter deposited on silicon substrates. The Raman data are interpreted by using data from resistivity measurements, Auger and Rutherford backscattering measurements, and scanning electron microscopy.

  16. Equipment simulation of selective tungsten deposition

    SciTech Connect

    Werner, C.; Ulacia, J.I.; Hopfmann, C.; Flynn, P. )

    1992-02-01

    This paper presents the numerical modeling of a cold wall reactor for selective tungsten chemical vapor deposition. In a two dimensional simulation the mass and heat transfer equations were solved considering the five chemical species H{sub 2}, WF{sub 6}, HF, WF{sub x}, and SiF{sub y}. Detailed models for multicomponent diffusion and for the autocatalytic tungsten nucleation process were implemented. Model results are in good agreement with experimental findings. The simulations are used to study the impact of reactor design on selectivity.

  17. Radiofrequency Spectroscopy and Thermodynamics of Fermi Gases in the 2D to Quasi-2D Dimensional Crossover

    NASA Astrophysics Data System (ADS)

    Cheng, Chingyun; Kangara, Jayampathi; Arakelyan, Ilya; Thomas, John

    2016-05-01

    We tune the dimensionality of a strongly interacting degenerate 6 Li Fermi gas from 2D to quasi-2D, by adjusting the radial confinement of pancake-shaped clouds to control the radial chemical potential. In the 2D regime with weak radial confinement, the measured pair binding energies are in agreement with 2D-BCS mean field theory, which predicts dimer pairing energies in the many-body regime. In the qausi-2D regime obtained with increased radial confinement, the measured pairing energy deviates significantly from 2D-BCS theory. In contrast to the pairing energy, the measured radii of the cloud profiles are not fit by 2D-BCS theory in either the 2D or quasi-2D regimes, but are fit in both regimes by a beyond mean field polaron-model of the free energy. Supported by DOE, ARO, NSF, and AFOSR.

  18. Competing coexisting phases in 2D water

    PubMed Central

    Zanotti, Jean-Marc; Judeinstein, Patrick; Dalla-Bernardina, Simona; Creff, Gaëlle; Brubach, Jean-Blaise; Roy, Pascale; Bonetti, Marco; Ollivier, Jacques; Sakellariou, Dimitrios; Bellissent-Funel, Marie-Claire

    2016-01-01

    The properties of bulk water come from a delicate balance of interactions on length scales encompassing several orders of magnitudes: i) the Hydrogen Bond (HBond) at the molecular scale and ii) the extension of this HBond network up to the macroscopic level. Here, we address the physics of water when the three dimensional extension of the HBond network is frustrated, so that the water molecules are forced to organize in only two dimensions. We account for the large scale fluctuating HBond network by an analytical mean-field percolation model. This approach provides a coherent interpretation of the different events experimentally (calorimetry, neutron, NMR, near and far infra-red spectroscopies) detected in interfacial water at 160, 220 and 250 K. Starting from an amorphous state of water at low temperature, these transitions are respectively interpreted as the onset of creation of transient low density patches of 4-HBonded molecules at 160 K, the percolation of these domains at 220 K and finally the total invasion of the surface by them at 250 K. The source of this surprising behaviour in 2D is the frustration of the natural bulk tetrahedral local geometry and the underlying very significant increase in entropy of the interfacial water molecules. PMID:27185018

  19. Competing coexisting phases in 2D water

    NASA Astrophysics Data System (ADS)

    Zanotti, Jean-Marc; Judeinstein, Patrick; Dalla-Bernardina, Simona; Creff, Gaëlle; Brubach, Jean-Blaise; Roy, Pascale; Bonetti, Marco; Ollivier, Jacques; Sakellariou, Dimitrios; Bellissent-Funel, Marie-Claire

    2016-05-01

    The properties of bulk water come from a delicate balance of interactions on length scales encompassing several orders of magnitudes: i) the Hydrogen Bond (HBond) at the molecular scale and ii) the extension of this HBond network up to the macroscopic level. Here, we address the physics of water when the three dimensional extension of the HBond network is frustrated, so that the water molecules are forced to organize in only two dimensions. We account for the large scale fluctuating HBond network by an analytical mean-field percolation model. This approach provides a coherent interpretation of the different events experimentally (calorimetry, neutron, NMR, near and far infra-red spectroscopies) detected in interfacial water at 160, 220 and 250 K. Starting from an amorphous state of water at low temperature, these transitions are respectively interpreted as the onset of creation of transient low density patches of 4-HBonded molecules at 160 K, the percolation of these domains at 220 K and finally the total invasion of the surface by them at 250 K. The source of this surprising behaviour in 2D is the frustration of the natural bulk tetrahedral local geometry and the underlying very significant increase in entropy of the interfacial water molecules.

  20. 2-D Animation's Not Just for Mickey Mouse.

    ERIC Educational Resources Information Center

    Weinman, Lynda

    1995-01-01

    Discusses characteristics of two-dimensional (2-D) animation; highlights include character animation, painting issues, and motion graphics. Sidebars present Silicon Graphics animations tools and 2-D animation programs for the desktop computer. (DGM)

  1. Redox potentials of tungsten and its alloying partners-fundamentals of tungsten determination by redox titration.

    PubMed

    Wünsch, G

    1980-08-01

    The fundamentals of tungsten determination by redox titration in hydrochloric acid medium are describe. Conditional redox potentials are given for W, Cr, V, Fe, Ti, Mo, Cu and Sn as a function of HCl concentration. The basic experimental conditions and the difference in conditional potentials required for consecutive titrations are discussed. Any mixture of tungsten with other metals can be analysed without separation if it does not contain both Cr and Ti or both Mo and V.

  2. Thermal cycling and high power density hydrogen ion beam irradiation of tungsten layers on tungsten substrate

    NASA Astrophysics Data System (ADS)

    Airapetov, A. A.; Begrambekov, L. B.; Gretskaya, I. Yu; Grunin, A. V.; Dyachenko, M. Yu; Puntakov, N. A.; Sadovskiy, Ya A.

    2016-09-01

    Tungsten layers with iron impurity were deposited on tungsten substrates modeling re-deposited layers in a fusion device. The samples were tested by thermocycling and hydrogen ion beam tests. Thermocycling revealed globule formation on the surface. The size of the globules depended on iron impurity content in the coating deposited. Pore formation was observed which in some cases lead to exfoliation of the coatings. Hydrogen ion irradiation lead to formation of blisters on the coating and finally its exfoliation.

  3. Pulmonary toxicity after exposure to military-relevant heavy metal tungsten alloy particles

    SciTech Connect

    Roedel, Erik Q.; Cafasso, Danielle E.; Lee, Karen W.M.; Pierce, Lisa M.

    2012-02-15

    Significant controversy over the environmental and public health impact of depleted uranium use in the Gulf War and the war in the Balkans has prompted the investigation and use of other materials including heavy metal tungsten alloys (HMTAs) as nontoxic alternatives. Interest in the health effects of HMTAs has peaked since the recent discovery that rats intramuscularly implanted with pellets containing 91.1% tungsten/6% nickel/2.9% cobalt rapidly developed aggressive metastatic tumors at the implantation site. Very little is known, however, regarding the cellular and molecular mechanisms associated with the effects of inhalation exposure to HMTAs despite the recognized risk of this route of exposure to military personnel. In the current study military-relevant metal powder mixtures consisting of 92% tungsten/5% nickel/3% cobalt (WNiCo) and 92% tungsten/5% nickel/3% iron (WNiFe), pure metals, or vehicle (saline) were instilled intratracheally in rats. Pulmonary toxicity was assessed by cytologic analysis, lactate dehydrogenase activity, albumin content, and inflammatory cytokine levels in bronchoalveolar lavage fluid 24 h after instillation. The expression of 84 stress and toxicity-related genes was profiled in lung tissue and bronchoalveolar lavage cells using real-time quantitative PCR arrays, and in vitro assays were performed to measure the oxidative burst response and phagocytosis by lung macrophages. Results from this study determined that exposure to WNiCo and WNiFe induces pulmonary inflammation and altered expression of genes associated with oxidative and metabolic stress and toxicity. Inhalation exposure to both HMTAs likely causes lung injury by inducing macrophage activation, neutrophilia, and the generation of toxic oxygen radicals. -- Highlights: ► Intratracheal instillation of W–Ni–Co and W–Ni–Fe induces lung inflammation in rats. ► W–Ni–Co and W–Ni–Fe alter expression of oxidative stress and toxicity genes. ► W

  4. Generates 2D Input for DYNA NIKE & TOPAZ

    SciTech Connect

    Hallquist, J. O.; Sanford, Larry

    1996-07-15

    MAZE is an interactive program that serves as an input and two-dimensional mesh generator for DYNA2D, NIKE2D, TOPAZ2D, and CHEMICAL TOPAZ2D. MAZE also generates a basic template for ISLAND input. MAZE has been applied to the generation of input data to study the response of two-dimensional solids and structures undergoing finite deformations under a wide variety of large deformation transient dynamic and static problems and heat transfer analyses.

  5. MAZE96. Generates 2D Input for DYNA NIKE & TOPAZ

    SciTech Connect

    Sanford, L.; Hallquist, J.O.

    1992-02-24

    MAZE is an interactive program that serves as an input and two-dimensional mesh generator for DYNA2D, NIKE2D, TOPAZ2D, and CHEMICAL TOPAZ2D. MAZE also generates a basic template for ISLAND input. MAZE has been applied to the generation of input data to study the response of two-dimensional solids and structures undergoing finite deformations under a wide variety of large deformation transient dynamic and static problems and heat transfer analyses.

  6. Molybdenum Incorporation in Tungsten Aldehyde Oxidoreductase Enzymes from Pyrococcus furiosus▿ †

    PubMed Central

    Sevcenco, Ana-Maria; Bevers, Loes E.; Pinkse, Martijn W. H.; Krijger, Gerard C.; Wolterbeek, Hubert T.; Verhaert, Peter D. E. M.; Hagen, Wilfred R.; Hagedoorn, Peter-Leon

    2010-01-01

    The hyperthermophilic archaeon Pyrococcus furiosus expresses five aldehyde oxidoreductase (AOR) enzymes, all containing a tungsto-bispterin cofactor. The growth of this organism is fully dependent on the presence of tungsten in the growth medium. Previous studies have suggested that molybdenum is not incorporated in the active site of these enzymes. Application of the radioisotope 99Mo in metal isotope native radioautography in gel electrophoresis (MIRAGE) technology to P. furiosus shows that molybdenum can in fact be incorporated in all five AOR enzymes. Mo(V) signals characteristic for molybdopterin were observed in formaldehyde oxidoreductase (FOR) in electron paramagnetic resonance (EPR)-monitored redox titrations. Our finding that the aldehyde oxidation activity of FOR and WOR5 (W-containing oxidoreductase 5) correlates only with the residual tungsten content suggests that the Mo-containing AORs are most likely inactive. An observed W/Mo antagonism is indicative of tungstate-dependent negative feedback of the expression of the tungstate/molybdate ABC transporter. An intracellular selection mechanism for tungstate and molybdate processing has to be present, since tungsten was found to be preferentially incorporated into the AORs even under conditions with comparable intracellular concentrations of tungstate and molybdate. Under the employed growth conditions of starch as the main carbon source in a rich medium, no tungsten- and/or molybdenum-associated proteins are detected in P. furiosus other than the high-affinity transporter, the proteins of the metallopterin insertion machinery, and the five W-AORs. PMID:20562313

  7. Spinarc gas tungsten arc torch holder

    NASA Technical Reports Server (NTRS)

    Brace, D. F.; Crockett, J. L.

    1970-01-01

    Semiautomatic welding torch enables operator to control arc length, torch angle, and spring tension when welding small diameter aluminum tubing. Tungsten is preset for the weld to make arc initiation easier and to eliminate searching for the joint through a dark welding lens.

  8. Joining of Tungsten Armor Using Functional Gradients

    SciTech Connect

    John Scott O'Dell

    2006-12-31

    The joining of low thermal expansion armor materials such as tungsten to high thermal expansion heat sink materials has been a major problem in plasma facing component (PFC) development. Conventional planar bonding techniques have been unable to withstand the high thermal induced stresses resulting from fabrication and high heat flux testing. During this investigation, innovative functional gradient joints produced using vacuum plasma spray forming techniques have been developed for joining tungsten armor to copper alloy heat sinks. A model was developed to select the optimum gradient architecture. Based on the modeling effort, a 2mm copper rich gradient was selected. Vacuum plasma pray parameters and procedures were then developed to produce the functional gradient joint. Using these techniques, dual cooling channel, medium scale mockups (32mm wide x 400mm length) were produced with vacuum plasma spray formed tungsten armor. The thickness of the tungsten armor was up to 5mm thick. No evidence of debonding at the interface between the heat sink and the vacuum plasma sprayed material was observed.

  9. Gas tungsten arc welder with electrode grinder

    DOEpatents

    Christiansen, David W.; Brown, William F.

    1984-01-01

    A welder for automated closure of fuel pins by a gas tungsten arc process in which a rotating length of cladding is positioned adjacent a welding electrode in a sealed enclosure. An independently movable axial grinder is provided in the enclosure for refurbishing the used electrode between welds.

  10. Aminobisphenolate supported tungsten disulphido and dithiolene complexes.

    PubMed

    Salojärvi, E; Peuronen, A; Sillanpää, R; Damlin, P; Kivelä, H; Lehtonen, A

    2015-05-28

    Dioxotungsten(vi) complexes with tetradentate amino bisphenolates were converted into the corresponding Cs-symmetric amino bisphenolate disulphido complexes by a reaction with either Lawesson's reagent or P2S5. Further reaction with diethyl acetylenedicarboxylate leads to the formation of diamagnetic tungsten(iv) dithiolene compounds. The syntheses, crystal structures, spectroscopic and electrochemical characterization of such disulphido and dithiolene complexes are presented.

  11. Detonation in tungsten-loaded HMX

    SciTech Connect

    Goldstein, S.; Mader, C.L.

    1985-01-01

    The detonation behavior of X-0233, a heavily tungsten-loaded HMX explosive, has been studied using failure diameter measurements, plate dents, and aquarium tests. A model with features resembling those of a weak detonation describe the experimental results. 7 refs., 10 figs.

  12. 2d PDE Linear Symmetric Matrix Solver

    1983-10-01

    ICCG2 (Incomplete Cholesky factorized Conjugate Gradient algorithm for 2d symmetric problems) was developed to solve a linear symmetric matrix system arising from a 9-point discretization of two-dimensional elliptic and parabolic partial differential equations found in plasma physics applications, such as resistive MHD, spatial diffusive transport, and phase space transport (Fokker-Planck equation) problems. These problems share the common feature of being stiff and requiring implicit solution techniques. When these parabolic or elliptic PDE''s are discretized withmore » finite-difference or finite-element methods,the resulting matrix system is frequently of block-tridiagonal form. To use ICCG2, the discretization of the two-dimensional partial differential equation and its boundary conditions must result in a block-tridiagonal supermatrix composed of elementary tridiagonal matrices. The incomplete Cholesky conjugate gradient algorithm is used to solve the linear symmetric matrix equation. Loops are arranged to vectorize on the Cray1 with the CFT compiler, wherever possible. Recursive loops, which cannot be vectorized, are written for optimum scalar speed. For matrices lacking symmetry, ILUCG2 should be used. Similar methods in three dimensions are available in ICCG3 and ILUCG3. A general source containing extensions and macros, which must be processed by a pre-compiler to obtain the standard FORTRAN source, is provided along with the standard FORTRAN source because it is believed to be more readable. The pre-compiler is not included, but pre-compilation may be performed by a text editor as described in the UCRL-88746 Preprint.« less

  13. 2d PDE Linear Asymmetric Matrix Solver

    1983-10-01

    ILUCG2 (Incomplete LU factorized Conjugate Gradient algorithm for 2d problems) was developed to solve a linear asymmetric matrix system arising from a 9-point discretization of two-dimensional elliptic and parabolic partial differential equations found in plasma physics applications, such as plasma diffusion, equilibria, and phase space transport (Fokker-Planck equation) problems. These equations share the common feature of being stiff and requiring implicit solution techniques. When these parabolic or elliptic PDE''s are discretized with finite-difference or finite-elementmore » methods, the resulting matrix system is frequently of block-tridiagonal form. To use ILUCG2, the discretization of the two-dimensional partial differential equation and its boundary conditions must result in a block-tridiagonal supermatrix composed of elementary tridiagonal matrices. A generalization of the incomplete Cholesky conjugate gradient algorithm is used to solve the matrix equation. Loops are arranged to vectorize on the Cray1 with the CFT compiler, wherever possible. Recursive loops, which cannot be vectorized, are written for optimum scalar speed. For problems having a symmetric matrix ICCG2 should be used since it runs up to four times faster and uses approximately 30% less storage. Similar methods in three dimensions are available in ICCG3 and ILUCG3. A general source, containing extensions and macros, which must be processed by a pre-compiler to obtain the standard FORTRAN source, is provided along with the standard FORTRAN source because it is believed to be more readable. The pre-compiler is not included, but pre-compilation may be performed by a text editor as described in the UCRL-88746 Preprint.« less

  14. Position control using 2D-to-2D feature correspondences in vision guided cell micromanipulation.

    PubMed

    Zhang, Yanliang; Han, Mingli; Shee, Cheng Yap; Ang, Wei Tech

    2007-01-01

    Conventional camera calibration that utilizes the extrinsic and intrinsic parameters of the camera and the objects has certain limitations for micro-level cell operations due to the presence of hardware deviations and external disturbances during the experimental process, thereby invalidating the extrinsic parameters. This invalidation is often neglected in macro-world visual servoing and affects the visual image processing quality, causing deviation from the desired position in micro-level cell operations. To increase the success rate of vision guided biological micromanipulations, a novel algorithm monitoring the changing image pattern of the manipulators including the injection micropipette and cell holder is designed and implemented based on 2 dimensional (2D)-to 2D feature correspondences and can adjust the manipulator and perform position control simultaneously. When any deviation is found, the manipulator is retracted to the initial focusing plane before continuing the operation.

  15. The oxidation of metals and alloys

    NASA Technical Reports Server (NTRS)

    Scheil, Erich

    1952-01-01

    This paper reviews the various types of oxidation processes occurring with pure metals and gives explanations for the varying time-temperature-oxidation rate relations that exist for copper, tungsten, zinc, cadmium, and tantalum. The effect of shape and crystal structure on oxidation is discussed. Principles derived are applied to the oxidation of alloys.

  16. A Planar Quantum Transistor Based on 2D-2D Tunneling in Double Quantum Well Heterostructures

    SciTech Connect

    Baca, W.E.; Blount, M.A.; Hafich, M.J.; Lyo, S.K.; Moon, J.S.; Reno, J.L.; Simmons, J.A.; Wendt, J.R.

    1998-12-14

    We report on our work on the double electron layer tunneling transistor (DELTT), based on the gate-control of two-dimensional -- two-dimensional (2D-2D) tunneling in a double quantum well heterostructure. While previous quantum transistors have typically required tiny laterally-defined features, by contrast the DELTT is entirely planar and can be reliably fabricated in large numbers. We use a novel epoxy-bond-and-stop-etch (EBASE) flip-chip process, whereby submicron gating on opposite sides of semiconductor epitaxial layers as thin as 0.24 microns can be achieved. Because both electron layers in the DELTT are 2D, the resonant tunneling features are unusually sharp, and can be easily modulated with one or more surface gates. We demonstrate DELTTs with peak-to-valley ratios in the source-drain I-V curve of order 20:1 below 1 K. Both the height and position of the resonant current peak can be controlled by gate voltage over a wide range. DELTTs with larger subband energy offsets ({approximately} 21 meV) exhibit characteristics that are nearly as good at 77 K, in good agreement with our theoretical calculations. Using these devices, we also demonstrate bistable memories operating at 77 K. Finally, we briefly discuss the prospects for room temperature operation, increases in gain, and high-speed.

  17. 'Brukin2D': a 2D visualization and comparison tool for LC-MS data

    PubMed Central

    Tsagkrasoulis, Dimosthenis; Zerefos, Panagiotis; Loudos, George; Vlahou, Antonia; Baumann, Marc; Kossida, Sophia

    2009-01-01

    Background Liquid Chromatography-Mass Spectrometry (LC-MS) is a commonly used technique to resolve complex protein mixtures. Visualization of large data sets produced from LC-MS, namely the chromatogram and the mass spectra that correspond to its compounds is the focus of this work. Results The in-house developed 'Brukin2D' software, built in Matlab 7.4, which is presented here, uses the compound data that are exported from the Bruker 'DataAnalysis' program, and depicts the mean mass spectra of all the chromatogram compounds from one LC-MS run, in one 2D contour/density plot. Two contour plots from different chromatograph runs can then be viewed in the same window and automatically compared, in order to find their similarities and differences. The results of the comparison can be examined through detailed mass quantification tables, while chromatogram compound statistics are also calculated during the procedure. Conclusion 'Brukin2D' provides a user-friendly platform for quick, easy and integrated view of complex LC-MS data. The software is available at . PMID:19534737

  18. Inhibition of human cytochrome P450 2D6 (CYP2D6) by methadone.

    PubMed Central

    Wu, D; Otton, S V; Sproule, B A; Busto, U; Inaba, T; Kalow, W; Sellers, E M

    1993-01-01

    1. In microsomes prepared from three human livers, methadone competitively inhibited the O-demethylation of dextromethorphan, a marker substrate for CYP2D6. The apparent Ki value of methadone ranged from 2.5 to 5 microM. 2. Two hundred and fifty-two (252) white Caucasians, including 210 unrelated healthy volunteers and 42 opiate abusers undergoing treatment with methadone were phenotyped using dextromethorphan as the marker drug. Although the frequency of poor metabolizers was similar in both groups, the extensive metabolizers among the opiate abusers tended to have higher O-demethylation metabolic ratios and to excrete less of the dose as dextromethorphan metabolites than control extensive metabolizer subjects. These data suggest inhibition of CYP2D6 by methadone in vivo as well. 3. Because methadone is widely used in the treatment of opiate abuse, inhibition of CYP2D6 activity in these patients might contribute to exaggerated response or unexpected toxicity from drugs that are substrates of this enzyme. PMID:8448065

  19. Electrokinetic treatment of firing ranges containing tungsten-contaminated soils.

    PubMed

    Braida, Washington; Christodoulatos, Christos; Ogundipe, Adebayo; Dermatas, Dimitris; O'Connor, Gregory

    2007-11-19

    Tungsten-based alloys and composites are being used and new formulations are being considered for use in the manufacturing of different types of ammunition. The use of tungsten heavy alloys (WHA) in new munitions systems and tungsten composites in small caliber ammunition could potentially release substantial amounts of this element into the environment. Although tungsten is widely used in industrial and military applications, tungsten's potential environmental and health impacts have not been thoroughly addressed. This necessitates the research and development of remedial technologies to contain and/or remove tungsten from soils that may serve as a source for water contamination. The current work investigates the feasibility of using electrokinetics for the remediation of tungsten-contaminated soils in the presence of other heavy metals of concern such as Cu and Pb with aim to removing W from the soil while stabilizing in situ, Pb and Cu. PMID:17686582

  20. Effect of CYP2D6 genetic polymorphism on the metabolism of citalopram in vitro.

    PubMed

    Hu, Xiao-Xia; Yuan, Ling-Jing; Fang, Ping; Mao, Yong-Hui; Zhan, Yun-Yun; Li, Xiang-Yu; Dai, Da-Peng; Cai, Jian-Ping; Hu, Guo-Xin

    2016-04-01

    Genetic polymorphisms of CYP2D6 significantly influence the efficacy and safety of some drugs, which might cause adverse effects and therapeutic failure. We aimed at investigating the role of CYP2D6 in the metabolism of citalopram and identifying the effect of 24 CYP2D6 allelic variants we found in Chinese Han population on the metabolism of citalopram in vitro. These CYP2D6 variants expressed by insect cells system were incubated with 10-1000 μM citalopram for 30 min at 37 °C and the reaction was terminated by cooling to -80 °C immediately. Citalopram and its metabolites were analyzed by high-performance liquid chromatography (HPLC). The intrinsic clearance (Vmax/Km) values of the variants toward citalopram metabolites were significantly altered, 38-129% for demethylcitalopram and 13-138% for citalopram N-oxide when compared with CYP2D6*1. Most of the tested rare alleles exhibited significantly decreased values due to increased Km and/or decreased Vmax values. We conclude that recombinant system could be used to investigate the enzymes involved in drug metabolism and these findings suggest that more attention should be paid to subjects carrying these CYP2D6 alleles when administering citalopram in the clinic. PMID:27016952

  1. Observation of two distinct negative trions in tungsten disulfide monolayers

    DOE PAGES

    Boulesbaa, Abdelaziz; Huang, Bing; Wang, Kai; Lin, Ming-Wei; Mahjouri-Samani, Masoud; Rouleau, Christopher M.; Xiao, Kai; Yoon, Mina; Sumpter, Bobby G.; Puretzky, Alexander A.; et al

    2015-09-25

    We report on the observation of two distinct photogenerated negative trion states TA and TB in two-dimensional tungsten disulfide (2D-WS2) monolayers. These trions are postulated to emerge from their parent excitons XA and XB, which originate from spin-orbit-split (SOS) levels in the conduction band (CB) and valence band (VB). Time-resolved spectroscopy measurements suggests that Pauli blocking controls a competition process between TA and TB photoformation, following dissociation of XA and XB through hole trapping at internal or substrate defect sites. While TA arises directly from its parent XA, TB emerges through a different transition accessible only after XB dissociates throughmore » a hole trapping channel. This discovery of additional optically-active band-edge transitions in atomically-thin metal dichalcogenides may revolutionize optoelectronic applications and fundamental research opportunities for many-body interaction physics. Ultrafast pump-probe spectroscopy of two-dimensional tungsten disulfide monolayers (2D-WS2) grown on sapphire substrates revealed two transient absorption spectral peaks that are attributed to distinct negative trions at ~2.02 eV (T1) and ~1.98 eV (T2). The dynamics measurements indicate that trion formation by the probe is enabled by photodoped electrons that remain after trapping of holes from excitons or free electron-hole pairs at defect sites in the crystal or on the substrate. Dynamics of the excitons XA and XB’s characteristic absorption bands, at ~2.03 and ~2.40 eV, respectively, were separately monitored and compared with the photoinduced absorption features. Selective excitation of the lowest exciton level XA using λpump < 2.4 eV forms only trion T1, which implies that the electron that remains from the dissociation of exciton XA is involved in the creation of this trion with a binding energy ~ 10 meV with respect to XA. The absorption peak that corresponds to trion T2 appears when λpump > 2.4 eV, which is just

  2. Observation of two distinct negative trions in tungsten disulfide monolayers

    SciTech Connect

    Boulesbaa, Abdelaziz; Huang, Bing; Wang, Kai; Lin, Ming-Wei; Mahjouri-Samani, Masoud; Rouleau, Christopher M.; Xiao, Kai; Yoon, Mina; Sumpter, Bobby G.; Puretzky, Alexander A.; Geohegan, David B.

    2015-09-25

    We report on the observation of two distinct photogenerated negative trion states TA and TB in two-dimensional tungsten disulfide (2D-WS2) monolayers. These trions are postulated to emerge from their parent excitons XA and XB, which originate from spin-orbit-split (SOS) levels in the conduction band (CB) and valence band (VB). Time-resolved spectroscopy measurements suggests that Pauli blocking controls a competition process between TA and TB photoformation, following dissociation of XA and XB through hole trapping at internal or substrate defect sites. While TA arises directly from its parent XA, TB emerges through a different transition accessible only after XB dissociates through a hole trapping channel. This discovery of additional optically-active band-edge transitions in atomically-thin metal dichalcogenides may revolutionize optoelectronic applications and fundamental research opportunities for many-body interaction physics. Ultrafast pump-probe spectroscopy of two-dimensional tungsten disulfide monolayers (2D-WS2) grown on sapphire substrates revealed two transient absorption spectral peaks that are attributed to distinct negative trions at ~2.02 eV (T1) and ~1.98 eV (T2). The dynamics measurements indicate that trion formation by the probe is enabled by photodoped electrons that remain after trapping of holes from excitons or free electron-hole pairs at defect sites in the crystal or on the substrate. Dynamics of the excitons XA and XB’s characteristic absorption bands, at ~2.03 and ~2.40 eV, respectively, were separately monitored and compared with the photoinduced absorption features. Selective excitation of the lowest exciton level XA using λpump < 2.4 eV forms only trion T1, which implies that the electron that remains

  3. Correlated Electron Phenomena in 2D Materials

    NASA Astrophysics Data System (ADS)

    Lambert, Joseph G.

    In this thesis, I present experimental results on coherent electron phenomena in layered two-dimensional materials: single layer graphene and van der Waals coupled 2D TiSe2. Graphene is a two-dimensional single-atom thick sheet of carbon atoms first derived from bulk graphite by the mechanical exfoliation technique in 2004. Low-energy charge carriers in graphene behave like massless Dirac fermions, and their density can be easily tuned between electron-rich and hole-rich quasiparticles with electrostatic gating techniques. The sharp interfaces between regions of different carrier densities form barriers with selective transmission, making them behave as partially reflecting mirrors. When two of these interfaces are set at a separation distance within the phase coherence length of the carriers, they form an electronic version of a Fabry-Perot cavity. I present measurements and analysis of multiple Fabry-Perot modes in graphene with parallel electrodes spaced a few hundred nanometers apart. Transition metal dichalcogenide (TMD) TiSe2 is part of the family of materials that coined the term "materials beyond graphene". It contains van der Waals coupled trilayer stacks of Se-Ti-Se. Many TMD materials exhibit a host of interesting correlated electronic phases. In particular, TiSe2 exhibits chiral charge density waves (CDW) below TCDW ˜ 200 K. Upon doping with copper, the CDW state gets suppressed with Cu concentration, and CuxTiSe2 becomes superconducting with critical temperature of T c = 4.15 K. There is still much debate over the mechanisms governing the coexistence of the two correlated electronic phases---CDW and superconductivity. I will present some of the first conductance spectroscopy measurements of proximity coupled superconductor-CDW systems. Measurements reveal a proximity-induced critical current at the Nb-TiSe2 interfaces, suggesting pair correlations in the pure TiSe2. The results indicate that superconducting order is present concurrently with CDW in

  4. CYP2D7 Sequence Variation Interferes with TaqMan CYP2D6*15 and *35 Genotyping

    PubMed Central

    Riffel, Amanda K.; Dehghani, Mehdi; Hartshorne, Toinette; Floyd, Kristen C.; Leeder, J. Steven; Rosenblatt, Kevin P.; Gaedigk, Andrea

    2016-01-01

    TaqMan™ genotyping assays are widely used to genotype CYP2D6, which encodes a major drug metabolizing enzyme. Assay design for CYP2D6 can be challenging owing to the presence of two pseudogenes, CYP2D7 and CYP2D8, structural and copy number variation and numerous single nucleotide polymorphisms (SNPs) some of which reflect the wild-type sequence of the CYP2D7 pseudogene. The aim of this study was to identify the mechanism causing false-positive CYP2D6*15 calls and remediate those by redesigning and validating alternative TaqMan genotype assays. Among 13,866 DNA samples genotyped by the CompanionDx® lab on the OpenArray platform, 70 samples were identified as heterozygotes for 137Tins, the key SNP of CYP2D6*15. However, only 15 samples were confirmed when tested with the Luminex xTAG CYP2D6 Kit and sequencing of CYP2D6-specific long range (XL)-PCR products. Genotype and gene resequencing of CYP2D6 and CYP2D7-specific XL-PCR products revealed a CC>GT dinucleotide SNP in exon 1 of CYP2D7 that reverts the sequence to CYP2D6 and allows a TaqMan assay PCR primer to bind. Because CYP2D7 also carries a Tins, a false-positive mutation signal is generated. This CYP2D7 SNP was also responsible for generating false-positive signals for rs769258 (CYP2D6*35) which is also located in exon 1. Although alternative CYP2D6*15 and *35 assays resolved the issue, we discovered a novel CYP2D6*15 subvariant in one sample that carries additional SNPs preventing detection with the alternate assay. The frequency of CYP2D6*15 was 0.1% in this ethnically diverse U.S. population sample. In addition, we also discovered linkage between the CYP2D7 CC>GT dinucleotide SNP and the 77G>A (rs28371696) SNP of CYP2D6*43. The frequency of this tentatively functional allele was 0.2%. Taken together, these findings emphasize that regardless of how careful genotyping assays are designed and evaluated before being commercially marketed, rare or unknown SNPs underneath primer and/or probe regions can impact

  5. CYP2D7 Sequence Variation Interferes with TaqMan CYP2D6 (*) 15 and (*) 35 Genotyping.

    PubMed

    Riffel, Amanda K; Dehghani, Mehdi; Hartshorne, Toinette; Floyd, Kristen C; Leeder, J Steven; Rosenblatt, Kevin P; Gaedigk, Andrea

    2015-01-01

    TaqMan™ genotyping assays are widely used to genotype CYP2D6, which encodes a major drug metabolizing enzyme. Assay design for CYP2D6 can be challenging owing to the presence of two pseudogenes, CYP2D7 and CYP2D8, structural and copy number variation and numerous single nucleotide polymorphisms (SNPs) some of which reflect the wild-type sequence of the CYP2D7 pseudogene. The aim of this study was to identify the mechanism causing false-positive CYP2D6 (*) 15 calls and remediate those by redesigning and validating alternative TaqMan genotype assays. Among 13,866 DNA samples genotyped by the CompanionDx® lab on the OpenArray platform, 70 samples were identified as heterozygotes for 137Tins, the key SNP of CYP2D6 (*) 15. However, only 15 samples were confirmed when tested with the Luminex xTAG CYP2D6 Kit and sequencing of CYP2D6-specific long range (XL)-PCR products. Genotype and gene resequencing of CYP2D6 and CYP2D7-specific XL-PCR products revealed a CC>GT dinucleotide SNP in exon 1 of CYP2D7 that reverts the sequence to CYP2D6 and allows a TaqMan assay PCR primer to bind. Because CYP2D7 also carries a Tins, a false-positive mutation signal is generated. This CYP2D7 SNP was also responsible for generating false-positive signals for rs769258 (CYP2D6 (*) 35) which is also located in exon 1. Although alternative CYP2D6 (*) 15 and (*) 35 assays resolved the issue, we discovered a novel CYP2D6 (*) 15 subvariant in one sample that carries additional SNPs preventing detection with the alternate assay. The frequency of CYP2D6 (*) 15 was 0.1% in this ethnically diverse U.S. population sample. In addition, we also discovered linkage between the CYP2D7 CC>GT dinucleotide SNP and the 77G>A (rs28371696) SNP of CYP2D6 (*) 43. The frequency of this tentatively functional allele was 0.2%. Taken together, these findings emphasize that regardless of how careful genotyping assays are designed and evaluated before being commercially marketed, rare or unknown SNPs underneath primer

  6. A molybdenum and a tungsten isoenzyme of formylmethanofuran dehydrogenase in the thermophilic archaeon Methanobacterium wolfei.

    PubMed

    Schmitz, R A; Albracht, S P; Thauer, R K

    1992-11-01

    We have recently reported that the thermophilic archaeon Methanobacterium wolfei contains two formylmethanofuran dehydrogenases, I and II. Formylmethanofuran dehydrogenase II, which is preferentially expressed in tungsten-grown cells, has been purified and shown to be a tungsten-iron-sulfur protein. We have now purified and characterized formylmethanofuran dehydrogenase I from molybdenum-grown cells and shown that it is a molybdenum-iron-sulfur protein. The purified enzyme, with a specific activity of 27 U/mg protein, was found to be composed of three subunits of apparent molecular mass 64 kDa, 51 kDa, and 31 kDa and to contain per mol 146-kDa molecule approximately 0.23 mol molybdenum, 0.46 mol molybdopterin guanine dinucleotide, and 6.6 mol non-heme iron but no tungsten (< 0.01 mol). The molybdenum enzyme differed from the tungsten enzyme (8 U/mg) in that it catalyzed the oxidation of N-furfurylformamide and formate and was inactivated by cyanide. The two enzymes also differed significantly in the pH optimum, in the apparent Km for the electron acceptor, and in the chromatographic behaviour. The molybdenum enzyme and the tungsten enzyme were similar, however, in that the N-terminal amino acid sequences determined for the alpha and beta subunits were identical up to residue 23, indicating that the two proteins are isoenzymes. The molybdenum enzyme, as isolated, was found to display an EPR signal derived from molybdenum as evidenced by isotope substitution.

  7. Tungsten-induced carcinogenesis in human bronchial epithelial cells.

    PubMed

    Laulicht, Freda; Brocato, Jason; Cartularo, Laura; Vaughan, Joshua; Wu, Feng; Kluz, Thomas; Sun, Hong; Oksuz, Betul Akgol; Shen, Steven; Peana, Massimiliano; Medici, Serenella; Zoroddu, Maria Antonietta; Costa, Max

    2015-10-01

    Metals such as arsenic, cadmium, beryllium, and nickel are known human carcinogens; however, other transition metals, such as tungsten (W), remain relatively uninvestigated with regard to their potential carcinogenic activity. Tungsten production for industrial and military applications has almost doubled over the past decade and continues to increase. Here, for the first time, we demonstrate tungsten's ability to induce carcinogenic related endpoints including cell transformation, increased migration, xenograft growth in nude mice, and the activation of multiple cancer-related pathways in transformed clones as determined by RNA sequencing. Human bronchial epithelial cell line (Beas-2B) exposed to tungsten developed carcinogenic properties. In a soft agar assay, tungsten-treated cells formed more colonies than controls and the tungsten-transformed clones formed tumors in nude mice. RNA-sequencing data revealed that the tungsten-transformed clones altered the expression of many cancer-associated genes when compared to control clones. Genes involved in lung cancer, leukemia, and general cancer genes were deregulated by tungsten. Taken together, our data show the carcinogenic potential of tungsten. Further tests are needed, including in vivo and human studies, in order to validate tungsten as a carcinogen to humans. PMID:26164860

  8. Tungsten-induced carcinogenesis in human bronchial epithelial cells.

    PubMed

    Laulicht, Freda; Brocato, Jason; Cartularo, Laura; Vaughan, Joshua; Wu, Feng; Kluz, Thomas; Sun, Hong; Oksuz, Betul Akgol; Shen, Steven; Peana, Massimiliano; Medici, Serenella; Zoroddu, Maria Antonietta; Costa, Max

    2015-10-01

    Metals such as arsenic, cadmium, beryllium, and nickel are known human carcinogens; however, other transition metals, such as tungsten (W), remain relatively uninvestigated with regard to their potential carcinogenic activity. Tungsten production for industrial and military applications has almost doubled over the past decade and continues to increase. Here, for the first time, we demonstrate tungsten's ability to induce carcinogenic related endpoints including cell transformation, increased migration, xenograft growth in nude mice, and the activation of multiple cancer-related pathways in transformed clones as determined by RNA sequencing. Human bronchial epithelial cell line (Beas-2B) exposed to tungsten developed carcinogenic properties. In a soft agar assay, tungsten-treated cells formed more colonies than controls and the tungsten-transformed clones formed tumors in nude mice. RNA-sequencing data revealed that the tungsten-transformed clones altered the expression of many cancer-associated genes when compared to control clones. Genes involved in lung cancer, leukemia, and general cancer genes were deregulated by tungsten. Taken together, our data show the carcinogenic potential of tungsten. Further tests are needed, including in vivo and human studies, in order to validate tungsten as a carcinogen to humans.

  9. Mechanical characterization of 2D, 2D stitched, and 3D braided/RTM materials

    NASA Technical Reports Server (NTRS)

    Deaton, Jerry W.; Kullerd, Susan M.; Portanova, Marc A.

    1993-01-01

    Braided composite materials have potential for application in aircraft structures. Fuselage frames, floor beams, wing spars, and stiffeners are examples where braided composites could find application if cost effective processing and damage tolerance requirements are met. Another important consideration for braided composites relates to their mechanical properties and how they compare to the properties of composites produced by other textile composite processes being proposed for these applications. Unfortunately, mechanical property data for braided composites do not appear extensively in the literature. Data are presented in this paper on the mechanical characterization of 2D triaxial braid, 2D triaxial braid plus stitching, and 3D (through-the-thickness) braid composite materials. The braided preforms all had the same graphite tow size and the same nominal braid architectures, (+/- 30 deg/0 deg), and were resin transfer molded (RTM) using the same mold for each of two different resin systems. Static data are presented for notched and unnotched tension, notched and unnotched compression, and compression after impact strengths at room temperature. In addition, some static results, after environmental conditioning, are included. Baseline tension and compression fatigue results are also presented, but only for the 3D braided composite material with one of the resin systems.

  10. Femtosecond fiber laser additive manufacturing of tungsten

    NASA Astrophysics Data System (ADS)

    Bai, Shuang; Liu, Jian; Yang, Pei; Zhai, Meiyu; Huang, Huan; Yang, Lih-Mei

    2016-04-01

    Additive manufacturing (AM) is promising to produce complex shaped components, including metals and alloys, to meet requirements from different industries such as aerospace, defense and biomedicines. Current laser AM uses CW lasers and very few publications have been reported for using pulsed lasers (esp. ultrafast lasers). In this paper, additive manufacturing of Tungsten materials is investigated by using femtosecond (fs) fiber lasers. Various processing conditions are studied, which leads to desired characteristics in terms of morphology, porosity, hardness, microstructural and mechanical properties of the processed components. Fully dense Tungsten part with refined grain and increased hardness was obtained and compared with parts made with different pulse widths and CW laser. The results are evidenced that the fs laser based AM provides more dimensions to modify mechanical properties with controlled heating, rapid melting and cooling rates compared with a CW or long pulsed laser. This can greatly benefit to the make of complicated structures and materials that could not be achieved before.

  11. Ultrasonic ranking of toughness of tungsten carbide

    NASA Technical Reports Server (NTRS)

    Vary, A.; Hull, D. R.

    1983-01-01

    The feasibility of using ultrasonic attenuation measurements to rank tungsten carbide alloys according to their fracture toughness was demonstrated. Six samples of cobalt-cemented tungsten carbide (WC-Co) were examined. These varied in cobalt content from approximately 2 to 16 weight percent. The toughness generally increased with increasing cobalt content. Toughness was first determined by the Palmqvist and short rod fracture toughness tests. Subsequently, ultrasonic attenuation measurements were correlated with both these mechanical test methods. It is shown that there is a strong increase in ultrasonic attenuation corresponding to increased toughness of the WC-Co alloys. A correlation between attenuation and toughness exists for a wide range of ultrasonic frequencies. However, the best correlation for the WC-Co alloys occurs when the attenuation coefficient measured in the vicinity of 100 megahertz is compared with toughness as determined by the Palmqvist technique.

  12. Computational Screening of 2D Materials for Photocatalysis.

    PubMed

    Singh, Arunima K; Mathew, Kiran; Zhuang, Houlong L; Hennig, Richard G

    2015-03-19

    Two-dimensional (2D) materials exhibit a range of extraordinary electronic, optical, and mechanical properties different from their bulk counterparts with potential applications for 2D materials emerging in energy storage and conversion technologies. In this Perspective, we summarize the recent developments in the field of solar water splitting using 2D materials and review a computational screening approach to rapidly and efficiently discover more 2D materials that possess properties suitable for solar water splitting. Computational tools based on density-functional theory can predict the intrinsic properties of potential photocatalyst such as their electronic properties, optical absorbance, and solubility in aqueous solutions. Computational tools enable the exploration of possible routes to enhance the photocatalytic activity of 2D materials by use of mechanical strain, bias potential, doping, and pH. We discuss future research directions and needed method developments for the computational design and optimization of 2D materials for photocatalysis.

  13. The tungsten divertor experiment at ASDEX Upgrade

    NASA Astrophysics Data System (ADS)

    Neu, R.; Asmussen, K.; Krieger, K.; Thoma, A.; Bosch, H.-S.; Deschka, S.; Dux, R.; Engelhardt, W.; García-Rosales, C.; Gruber, O.; Herrmann, A.; Kallenbach, A.; Kaufmann, M.; Mertens, V.; Ryter, F.; Rohde, V.; Roth, J.; Sokoll, M.; Stäbler, A.; Suttrop, W.; Weinlich, M.; Zohm, H.; Alexander, M.; Becker, G.; Behler, K.; Behringer, K.; Behrisch, R.; Bergmann, A.; Bessenrodt-Weberpals, M.; Brambilla, M.; Brinkschulte, H.; Büchl, K.; Carlson, A.; Chodura, R.; Coster, D.; Cupido, L.; de Blank, H. J.; de Peña Hempel, S.; Drube, R.; Fahrbach, H.-U.; Feist, J.-H.; Feneberg, W.; Fiedler, S.; Franzen, P.; Fuchs, J. C.; Fußmann, G.; Gafert, J.; Gehre, O.; Gernhardt, J.; Haas, G.; Herppich, G.; Herrmann, W.; Hirsch, S.; Hoek, M.; Hoenen, F.; Hofmeister, F.; Hohenöcker, H.; Jacobi, D.; Junker, W.; Kardaun, O.; Kass, T.; Kollotzek, H.; Köppendörfer, W.; Kurzan, B.; Lackner, K.; Lang, P. T.; Lang, R. S.; Laux, M.; Lengyel, L. L.; Leuterer, F.; Manso, M. E.; Maraschek, M.; Mast, K.-F.; McCarthy, P.; Meisel, D.; Merkel, R.; Müller, H. W.; Münich, M.; Murmann, H.; Napiontek, B.; Neu, G.; Neuhauser, J.; Niethammer, M.; Noterdaeme, J.-M.; Pasch, E.; Pautasso, G.; Peeters, A. G.; Pereverzev, G.; Pitcher, C. S.; Poschenrieder, W.; Raupp, G.; Reinmüller, K.; Riedl, R.; Röhr, H.; Salzmann, H.; Sandmann, W.; Schilling, H.-B.; Schlögl, D.; Schneider, H.; Schneider, R.; Schneider, W.; Schramm, G.; Schweinzer, J.; Scott, B. D.; Seidel, U.; Serra, F.; Speth, E.; Silva, A.; Steuer, K.-H.; Stober, J.; Streibl, B.; Treutterer, W.; Troppmann, M.; Tsois, N.; Ulrich, M.; Varela, P.; Verbeek, H.; Verplancke, Ph; Vollmer, O.; Wedler, H.; Wenzel, U.; Wesner, F.; Wolf, R.; Wunderlich, R.; Zasche, D.; Zehetbauer, T.; Zehrfeld, H.-P.

    1996-12-01

    Tungsten-coated tiles, manufactured by plasma spray on graphite, were mounted in the divertor of the ASDEX Upgrade tokamak and cover almost 90% of the surface facing the plasma in the strike zone. Over 600 plasma discharges have been performed to date, around 300 of which were auxiliary heated with heating powers up to 10 MW. The production of tungsten in the divertor was monitored by a W I line at 400.8 nm. In the plasma centre an array of spectral lines at 5 nm emitted by ionization states around W XXX was measured. From the intensity of these lines the W content was derived. Under normal discharge conditions W-concentrations around 0741-3335/38/12A/013/img12 or even lower were found. The influence on the main plasma parameters was found to be negligible. The maximum concentrations observed decrease with increasing heating power. In several low power discharges accumulation of tungsten occurred and the temperature profile was flattened. The concentrations of the intrinsic impurities carbon and oxygen were comparable to the discharges with the graphite divertor. Furthermore, the density and the 0741-3335/38/12A/013/img13 limits remained unchanged and no negative influence on the energy confinement or on the H-mode threshold was found. Discharges with neon radiative cooling showed the same behaviour as in the graphite divertor case.

  14. Tungsten-uranium penetrator target interaction

    SciTech Connect

    Dunn, P S; Damkroger, B K

    1994-10-01

    Several studies performed in recent years have been directed at determining the penetration mechanism of long rod kinetic energy penetrators into Rolled Homogeneous Armor (RHA). Much of the work has centered on comparing U-0.75Ti and Tungsten Heavy Alloys (WHA), with the goal being to relate the superior ballistic performance of the uranium materials to a fundamental difference in penetration mechanisms. This has been found to be true, with the dominant mechanisms being adiabatic shear in U-0.75Ti and bulk deformation in WHA. Recent work has sought to achieve improvements in the ballistic performance of the tungsten materials via both mechanical property improvements and alloy modifications designed to bring about adiabatic shear. As an alternative, the authors propose the consideration of materials which utilize mechanisms other than bulk deformation and adiabatic shear to optimize ballistic performance. This paper will present the postmortem analysis of a uranium-20 vol% tungsten composite penetrator fired into RHA at 0{degrees} obliquity. The analysis shows that the penetration mechanism in this material is bulk heating and extensive co-melting of the target and penetrator at the penetration interface. The results of the analysis will then be compared to a similar analysis made of targets into which U-0.75Ti penetrators had been fired.

  15. Controlled nanostructuration of polycrystalline tungsten thin films

    SciTech Connect

    Girault, B.; Eyidi, D.; Goudeau, P.; Guerin, P.; Bourhis, E. Le; Renault, P.-O.; Sauvage, T.

    2013-05-07

    Nanostructured tungsten thin films have been obtained by ion beam sputtering technique stopping periodically the growing. The total thickness was maintained constant while nanostructure control was obtained using different stopping periods in order to induce film stratification. The effect of tungsten sublayers' thicknesses on film composition, residual stresses, and crystalline texture evolution has been established. Our study reveals that tungsten crystallizes in both stable {alpha}- and metastable {beta}-phases and that volume proportions evolve with deposited sublayers' thicknesses. {alpha}-W phase shows original fiber texture development with two major preferential crystallographic orientations, namely, {alpha}-W<110> and unexpectedly {alpha}-W<111> texture components. The partial pressure of oxygen and presence of carbon have been identified as critical parameters for the growth of metastable {beta}-W phase. Moreover, the texture development of {alpha}-W phase with two texture components is shown to be the result of a competition between crystallographic planes energy minimization and crystallographic orientation channeling effect maximization. Controlled grain size can be achieved for the {alpha}-W phase structure over 3 nm stratification step. Below, the {beta}-W phase structure becomes predominant.

  16. Measurement of thermophysical property of plasma forming tungsten nanofiber layer

    NASA Astrophysics Data System (ADS)

    Kajita, Shin; Yagi, Takashi; Kobayashi, Kenichi; Tokitani, Masayuki; Ohno, Noriyasu

    2016-05-01

    Thermophysical property of a nanostructured tungsten layer formed on a tungsten film was investigated. A 1-µm-thick tungsten film deposited on a quartz glass substrate was irradiated with a high density helium plasma at the surface temperature of 1500 K. The plasma irradiation led to the formation of highly porous fiberform-nanostructured tungsten layer with a thickness of 3.5 µm. Impulse heating was applied at the interface of the film/substrate, and transient heat diffusion was observed using a pulsed light heating thermoreflectance apparatus. The thermoreflectance signals clearly differed between the nanostructure existing and mechanically removed regions; the difference can be attributed to thermal effusivity of the nanostructured tungsten layer. The estimated thermal conductivity of the nanostructured tungsten decreases to ∼2% of that of bulk when the density of the nanostructure is assumed to be ∼6% of the bulk value.

  17. Synthetic Covalent and Non-Covalent 2D Materials.

    PubMed

    Boott, Charlotte E; Nazemi, Ali; Manners, Ian

    2015-11-16

    The creation of synthetic 2D materials represents an attractive challenge that is ultimately driven by their prospective uses in, for example, electronics, biomedicine, catalysis, sensing, and as membranes for separation and filtration. This Review illustrates some recent advances in this diverse field with a focus on covalent and non-covalent 2D polymers and frameworks, and self-assembled 2D materials derived from nanoparticles, homopolymers, and block copolymers.

  18. A Geometric Boolean Library for 2D Objects

    2006-01-05

    The 2D Boolean Library is a collection of C++ classes -- which primarily represent 2D geometric data and relationships, and routines -- which contain algorithms for 2D geometric Boolean operations and utility functions. Classes are provided for 2D points, lines, arcs, edgeuses, loops, surfaces and mask sets. Routines are provided that incorporate the Boolean operations Union(OR), XOR, Intersection and Difference. Various analytical geometry routines and routines for importing and exporting the data in various filemore » formats, are also provided in the library.« less

  19. VizieR Online Data Catalog: The 2dF Galaxy Redshift Survey (2dFGRS) (2dFGRS Team, 1998-2003)

    NASA Astrophysics Data System (ADS)

    Colless, M.; Dalton, G.; Maddox, S.; Sutherland, W.; Norberg, P.; Cole, S.; Bland-Hawthorn, J.; Bridges, T.; Cannon, R.; Collins, C.; Couch, W.; Cross, N.; Deeley, K.; de Propris, R.; Driver, S. P.; Efstathiou, G.; Ellis, R. S.; Frenk, C. S.; Glazebrook, K.; Jackson, C.; Lahav, O.; Lewis, I.; Lumsden, S.; Madgwick, D.; Peacock, J. A.; Peterson, B. A.; Price, I.; Seaborne, M.; Taylor, K.

    2007-11-01

    The 2dF Galaxy Redshift Survey (2dFGRS) is a major spectroscopic survey taking full advantage of the unique capabilities of the 2dF facility built by the Anglo-Australian Observatory. The 2dFGRS is integrated with the 2dF QSO survey (2QZ, Cat. VII/241). The 2dFGRS obtained spectra for 245591 objects, mainly galaxies, brighter than a nominal extinction-corrected magnitude limit of bJ=19.45. Reliable (quality>=3) redshifts were obtained for 221414 galaxies. The galaxies cover an area of approximately 1500 square degrees selected from the extended APM Galaxy Survey in three regions: a North Galactic Pole (NGP) strip, a South Galactic Pole (SGP) strip, and random fields scattered around the SGP strip. Redshifts are measured from spectra covering 3600-8000 Angstroms at a two-pixel resolution of 9.0 Angstrom and a median S/N of 13 per pixel. All redshift identifications are visually checked and assigned a quality parameter Q in the range 1-5; Q>=3 redshifts are 98.4% reliable and have an rms uncertainty of 85 km/s. The overall redshift completeness for Q>=3 redshifts is 91.8% but this varies with magnitude from 99% for the brightest galaxies to 90% for objects at the survey limit. The 2dFGRS data base is available on the World Wide Web at http://www.mso.anu.edu.au/2dFGRS/. (6 data files).

  20. Immunological Visibility: Posttranscriptional Regulation of Human NKG2D Ligands by the EGF Receptor Pathway

    PubMed Central

    Vantourout, Pierre; Willcox, Carrie; Turner, Andrea; Swanson, Chad; Haque, Yasmin; Sobolev, Olga; Grigoriadis, Anita; Tutt, Andrew; Hayday, Adrian

    2014-01-01

    Human cytolytic T lymphocytes and NK cells can limit tumor growth and are being increasingly harnessed for tumor immunotherapy. One way cytolytic lymphocytes recognize tumor cells is by engagement of their activating receptor, NKG2D, by stress-antigens of the MICA/B and ULBP families. This study shows that surface upregulation of NKG2D ligands by human epithelial cells in response to ultraviolet irradiation, osmotic shock, oxidative stress, and growth factor provision, is attributable to activation of the EGF-receptor (EGFR). EGFR activation causes intracellular re-localisation of AUF1 proteins that ordinarily destabilise NKG2D ligand mRNAs by targeting an AU-rich element conserved within the 3′ ends of most human but not murine NKG2D ligand genes. Consistent with these findings, NKG2D ligand expression by primary human carcinomas positively correlated with EGFR expression that is commonly hyper-activated in such tumours, and was reduced by clinical EGFR inhibitors. Thus, stress-induced activation of EGFR not only regulates cell growth but concomitantly regulates the cells’ immunological visibility. Thus, therapeutics designed to limit cancer cell growth should also be considered in terms of their impact on immunosurveillance. PMID:24718859