Science.gov

Sample records for 3 otm development task

  1. DEVELOPMENT OF OTM SYNGAS PROCESS AND TESTING OF SYNGAS-DERIVED ULTRA-CLEAN FUELS IN DIESEL ENGINES AND FUEL CELLS

    SciTech Connect

    E.T. Robinson; James P. Meagher; Ravi Prasad

    2001-10-31

    This topical report summarizes work accomplished for the Program from January 1 through September 15, 2001 in the following task areas: Task 1--materials development; Task 2--composite element development; Task 3--tube fabrication; Task 4--reactor design and process optimization; Task 5--catalyst development; Task 6--P-1 operation; Task 8--fuels and engine testing; and Task 10--project management. OTM benchmark material, LCM1, exceeds the commercial oxygen flux target and was determined to be sufficiently robust to carry on process development activities. Work will continue on second-generation OTM materials that will satisfy commercial life targets. Three fabrication techniques for composite elements were determined to be technically feasible. These techniques will be studied and a lead manufacturing process for both small and large-scale elements will be selected in the next Budget Period. Experiments in six P-0 reactors, the long tube tester (LTT) and the P-1 pilot plant were conducted. Significant progress in process optimization was made through both the experimental program and modeling studies of alternate reactor designs and process configurations. Three tailored catalyst candidates for use in OTM process reactors were identified. Fuels for the International diesel engine and Nuvera fuel cell tests were ordered and delivered. Fuels testing and engine development work is now underway.

  2. Development of EPA OTM 10 for Landfill Applications

    EPA Science Inventory

    In 2006, the U.S. Environmental Protection Agency posted a new test method on its website called OTM 10 which describes direct measurement of pollutant mass emission flux from area sources using ground-based optical remote sensing. The method has validated application to relative...

  3. Development of OTM Syngas Process and Testing of Syngas Derived Ulta-clean Fuels in Diesel Engines and Fuel Cells Budget Period 3

    SciTech Connect

    E.T. Robinson; John Sirman; Prasad Apte; Xingun Gui; Tytus R. Bulicz; Dan Corgard; Siv Aasland; Kjersti Kleveland; Ann Hooper; Leo Bonnell; John Hemmings; Jack Chen; Bart A. Van Hassel

    2004-12-31

    This topical report summarizes work accomplished for the Program from January 1, 2003 through December 31,2004 in the following task areas: Task 1--Materials Development; Task 2--Composite Development; Task 4--Reactor Design and Process Optimization; Task 8--Fuels and Engine Testing; 8.1 International Diesel Engine Program; and Task IO: Program Management. Most of the key technical objectives for this budget period were achieved. Only partial success was achieved relative to cycle testing under pressure Major improvements in material performance and element reliability have been achieved. A breakthrough material system has driven the development of a compact planar reactor design capable of producing either hydrogen or syngas. The planar reactor shows significant advantages in thermal efficiency and costs compared to either steam methane reforming with CO{sub 2} recovery or autothermal reforming. The fuel and engine testing program is complete The single cylinder test engine evaluation of UCTF fuels begun in Budget Period 2 was finished this budget period. In addition, a study to evaluate new fuel formulations for an HCCl engine was completed.

  4. Development of OTM Syngas Process and Testing of Syngas Derived Ultra-clean Fuels in Diesel Engines and Fuel Cells

    SciTech Connect

    E.T. Robinson; John Sirman; Prasad Apte; Xingun Gui; Tytus R. Bulicz; Dan Corgard; John Hemmings

    2005-05-01

    This final report summarizes work accomplished in the Program from January 1, 2001 through December 31, 2004. Most of the key technical objectives for this program were achieved. A breakthrough material system has lead to the development of an OTM (oxygen transport membrane) compact planar reactor design capable of producing either syngas or hydrogen. The planar reactor shows significant advantages in thermal efficiency and a step change reduction in costs compared to either autothermal reforming or steam methane reforming with CO{sub 2} recovery. Syngas derived ultra-clean transportation fuels were tested in the Nuvera fuel cell modular pressurized reactor and in International Truck and Engine single cylinder test engines. The studies compared emission and engine performance of conventional base fuels to various formulations of ultra-clean gasoline or diesel fuels. A proprietary BP oxygenate showed significant advantage in both applications for reducing emissions with minimal impact on performance. In addition, a study to evaluate new fuel formulations for an HCCI engine was completed.

  5. Development of OTM Syngas Process and Testing of Syngas Derived Ultra-clean Fuels in Diesel Engines and Fuel Cells

    SciTech Connect

    E.T. Robinson; James P. Meagher; Prasad Apte; Xingun Gui; Tytus R. Bulicz; Siv Aasland; Charles Besecker; Jack Chen Bart A. van Hassel; Olga Polevaya; Rafey Khan; Piyush Pilaniwalla

    2002-12-31

    This topical report summarizes work accomplished for the Program from November 1, 2001 to December 31, 2002 in the following task areas: Task 1: Materials Development; Task 2: Composite Development; Task 4: Reactor Design and Process Optimization; Task 8: Fuels and Engine Testing; 8.1 International Diesel Engine Program; 8.2 Nuvera Fuel Cell Program; and Task 10: Program Management. Major progress has been made towards developing high temperature, high performance, robust, oxygen transport elements. In addition, a novel reactor design has been proposed that co-produces hydrogen, lowers cost and improves system operability. Fuel and engine testing is progressing well, but was delayed somewhat due to the hiatus in program funding in 2002. The Nuvera fuel cell portion of the program was completed on schedule and delivered promising results regarding low emission fuels for transportation fuel cells. The evaluation of ultra-clean diesel fuels continues in single cylinder (SCTE) and multiple cylinder (MCTE) test rigs at International Truck and Engine. FT diesel and a BP oxygenate showed significant emissions reductions in comparison to baseline petroleum diesel fuels. Overall through the end of 2002 the program remains under budget, but behind schedule in some areas.

  6. Moving Bed, Granular Bed Filter Development Program: Option 1, Component Test Facility. Task 3, Test plan

    SciTech Connect

    Haas, J.C.; Purdhomme, J.W.; Wilson, K.B.

    1994-04-01

    In the base contract, Combustion Power Co. developed commercial designs for a moving granular-bed filter (GBF). The proposed filter is similar to previous designs in terms of its shape and method of filtration. The commercial designs have scaled the filter from a 5 ft diameter to as large as a 20 ft diameter filter. In Task 2 of the Moving Bed-Granular Filter Development Program, all technical concerns related to the further development of the filter are identified. These issues are discussed in a Topical Report which has been issued as part of Task 2. Nineteen issues are identified in this report. Along with a discussion of these issues are the planned approaches for resolving each of these issues. These issues will be resolved in either a cold flow component test facility or in pilot scale testing at DOE`s Power System Development Facility (PSDF) located at Southem Company Services` Wilsonville facility. Task 3 presents a test plan for resolving those issues which can be addressed in component test facilities. The issues identified in Task 2 which will be addressed in the component test facilities are: GBF scale-up; effect of filter cone angle and sidewall materials on medium flow and ash segregation; maximum gas filtration rate; lift pipe wear; GBF media issues; mechanical design of the gas inlet duct; and filter pressure drop. This document describes a test program to address these issues, with testing to be performed at Combustion Power Company`s facility in Belmont, California.

  7. DOE-OTM Tribology Program; Quarterly progress report, January 1991--March 1991

    SciTech Connect

    Nichols, F. A.; Michaels, A. I.

    1991-07-01

    The OTM Tribology Program supports generic, long-term, high-risk applied research and exploratory development which private enterprise will not or cannot pursue, in areas pertaining to energy conservation in the transportation sector. This report presents work in the three areas of the tribology program: extreme environment lubrication, engineered tribological interfaces, and tribology by design.

  8. Space station operations task force. Panel 3 report: User development and integration

    NASA Technical Reports Server (NTRS)

    1987-01-01

    The User Development and Integration Panel of the Space Station Operations Task Force was chartered to develop concepts relating to the operations of the Space Station manned base and the platforms, user accommodation and integration activities. The needs of the user community are addressed in the context with the mature operations phase of the Space Station. Issues addressed include space station pricing options, marketing strategies, payload selection and resource allocation options, and manifesting techniques.

  9. Advanced turbine systems program conceptual design and product development. Task 3 -- System selection; Topical report

    SciTech Connect

    White, D.J.

    1994-07-01

    Solar Turbines Incorporated has elected to pursue an intercooled and recuperated (ICR) gas turbine system to exceed the goals of the DOE Advanced Turbine Systems (ATS) program, which are to develop and commercialize an industrial gas turbine system that operates at thermal efficiencies at least 15% higher than 1991 products, and with emissions not exceeding eight ppmv NOx and 20 ppmv CO and UHC. Solar`s goal is to develop a commercially viable industrial system (3--20 MW) driven by a gas turbine engine with a thermal efficiency of 50% (ATS50), with the flexibility to meet the differing operational requirements of various markets. Dispersed power generation is currently considered to be the primary future target market for the ICR in the 5--15 MW size class. The ICR integrated system approach provides an ideal candidate for the assumed dispersed power market, with its small footprint, easy transportability, and environmental friendliness. In comparison with other systems that use water or toxic chemicals such as ammonia for NOx control, the ICR has no consumables other than fuel and air. The low pressure ratio of the gas turbine engine also is favorable in that less parasitic power is needed to pump the natural gas into the combustor than for simple-cycle machines. Solar has narrowed the ICR configuration to two basic approaches, a 1-spool, and a 2-spool version of the ATS50. The 1-spool engine will have a lower first-cost but lower part-power efficiencies. The 2-spool ATS may not only have better part-power efficiency, its efficiency will also be less sensitive to reduced turbine rotor inlet temperature levels. Thus hot-end parts life can be increased with only small sacrifices in efficiency. The flexibility of the 2-spool arrangement in meeting customer needs is its major advantage over the 1-spool. This Task 3 Topical Report is intended to present Solar`s preliminary system selection based upon the initial trade-off studies performed to date.

  10. Blade loss transient dynamics analysis, volume 2. Task 2: Theoretical and analytical development. Task 3: Experimental verification

    NASA Technical Reports Server (NTRS)

    Gallardo, V. C.; Storace, A. S.; Gaffney, E. F.; Bach, L. J.; Stallone, M. J.

    1981-01-01

    The component element method was used to develop a transient dynamic analysis computer program which is essentially based on modal synthesis combined with a central, finite difference, numerical integration scheme. The methodology leads to a modular or building-block technique that is amenable to computer programming. To verify the analytical method, turbine engine transient response analysis (TETRA), was applied to two blade-out test vehicles that had been previously instrumented and tested. Comparison of the time dependent test data with those predicted by TETRA led to recommendations for refinement or extension of the analytical method to improve its accuracy and overcome its shortcomings. The development of working equations, their discretization, numerical solution scheme, the modular concept of engine modelling, the program logical structure and some illustrated results are discussed. The blade-loss test vehicles (rig full engine), the type of measured data, and the engine structural model are described.

  11. Online Toxicity Monitors (OTM) for Distribution System Water Quality Monitoring

    EPA Science Inventory

    Drinking water distribution systems in the U.S. are vulnerable to episodic contamination events (both unintentional and intentional). The U.S. Environmental Protection Agency (EPA) is conducting research to investigate the use of broad-spectrum online toxicity monitors (OTMs) in ...

  12. Ferrocyanide safety project: Task 3. 5 cyanide species analytical methods development

    SciTech Connect

    Bryan, S.A.; Pool, K.H.; Burger, L.L.; Carlson, C.D.; Hess, N.J.; Matheson, J.D.; Ryan, J.L.; Scheele, R.D.; Tingey, J.M.

    1993-01-01

    This report summarizes the results of studies conducted in FY 1992 to develop methods for the identification and quantification of cyanide species in ferrocyanide tank waste. Currently there are 24 high-level waste storage tanks at the Hanford Site that have been placed on a Ferrocyanide Tank Watchlist because they contain an estimated 1,000 g-moles or greater amount of precipitated ferrocyanide. This amount of ferrocyanide is of concern because the consequences of a potential explosion may exceed those reported previously in safety analyses. The threshold concentration of total cyanide within the tank waste matrix that is expected to be a safety concern is estimated at approximately 1 to 3 wt%. Methods for detection and speciation of ferrocyanide complexes in actual waste are needed to definitively measure and quantitate the amount of ferrocyanides present within actual waste tanks to a lower limit of at least 0.1 wt% in order to bound the safety concern.

  13. Ferrocyanide safety project: Task 3.5 cyanide species analytical methods development. FY 1992 annual report

    SciTech Connect

    Bryan, S.A.; Pool, K.H.; Burger, L.L.; Carlson, C.D.; Hess, N.J.; Matheson, J.D.; Ryan, J.L.; Scheele, R.D.; Tingey, J.M.

    1993-01-01

    This report summarizes the results of studies conducted in FY 1992 to develop methods for the identification and quantification of cyanide species in ferrocyanide tank waste. Currently there are 24 high-level waste storage tanks at the Hanford Site that have been placed on a Ferrocyanide Tank Watchlist because they contain an estimated 1,000 g-moles or greater amount of precipitated ferrocyanide. This amount of ferrocyanide is of concern because the consequences of a potential explosion may exceed those reported previously in safety analyses. The threshold concentration of total cyanide within the tank waste matrix that is expected to be a safety concern is estimated at approximately 1 to 3 wt%. Methods for detection and speciation of ferrocyanide complexes in actual waste are needed to definitively measure and quantitate the amount of ferrocyanides present within actual waste tanks to a lower limit of at least 0.1 wt% in order to bound the safety concern.

  14. Heat pump concepts for nZEB Technology developments, design tools and testing of heat pump systems for nZEB in the USA: Country report IEA HPT Annex 40 Task 2, Task 3 and Task 4 of the USA

    SciTech Connect

    Baxter, Van D.; Payne, W. Vance; Ling, Jiazhen; Radermacher, Reinhard

    2015-12-01

    The IEA HPT Annex 40 "Heat pump concepts for Nearly Zero Energy Buildings" deals with the application of heat pumps as a core component of the HVAC system for Nearly or Net Zero energy buildings (nZEB). This report covers Task 2 on the system comparison and optimisation and Task 3 dedicated to the development of adapted technologies for nZEB and field monitoring results of heat pump systems in nZEB. In the US team three institutions are involved and have worked on the following projects: The Oak Ridge National Laboratory (ORNL) will summarize development activities through the field demonstration stage for several integrated heat pump (IHP) systems electric ground-source (GS-IHP) and air-source (AS-IHP) versions and an engine driven AS-IHP version. The first commercial GS-IHP product was just introduced to the market in December 2012. This work is a contribution to Task 3 of the Annex. The University of Maryland will contribute a software development project to Task 2 of the Annex. The software ThermCom evaluates occupied space thermal comfort conditions accounting for all radiative and convective heat transfer effects as well as local air properties. The National Institute of Standards and Technology (NIST) is working on a field study effort on the NIST Net Zero Energy Residential Test Facility (NZERTF). This residential building was constructed on the NIST campus and officially opened in summer 2013. During the first year, between July 2013 and June 2014, baseline performance of the NZERTF was monitored under a simulated occupancy protocol. The house was equipped with an air-to-air heat pump which included a dedicated dehumidification operating mode. Outdoor conditions, internal loads and modes of heat pump operation were monitored. Field study results with respect to heat pump operation will be reported and recommendations on heat pump optimization for a net zero energy building will be provided. This work is a contribution to Task 3 of the Annex.

  15. Development of strain tolerant thermal barrier coating systems, tasks 1 - 3

    NASA Technical Reports Server (NTRS)

    Anderson, N. P.; Sheffler, K. D.

    1983-01-01

    Insulating ceramic thermal barrier coatings can reduce gas turbine airfoil metal temperatures as much as 170 C (about 300 F), providing fuel efficiency improvements greater than one percent and durability improvements of 2 to 3X. The objective was to increase the spalling resistance of zirconia based ceramic turbine coatings. To accomplish this, two baseline and 30 candidate duplex (layered MCrAlY/zirconia based ceramic) coatings were iteratively evaluated microstructurally and in four series of laboratory burner rig tests. This led to the selection of two candidate optimized 0.25 mm (0.010 inch) thick plasma sprayed partially stabilized zirconia ceramics containing six weight percent yttria and applied with two different sets of process parameters over a 0.13 mm (0.005 inch) thick low pressure chamber sprayed MCrAlY bond coat. Both of these coatings demonstrated at least 3X laboratory cyclic spalling life improvement over the baseline systems, as well as cyclic oxidation life equivalent to 15,000 commercial engine flight hours.

  16. TASK-1 and TASK-3 may form heterodimers in human atrial cardiomyocytes.

    PubMed

    Rinné, Susanne; Kiper, Aytug K; Schlichthörl, Günter; Dittmann, Sven; Netter, Michael F; Limberg, Sven H; Silbernagel, Nicole; Zuzarte, Marylou; Moosdorf, Rainer; Wulf, Hinnerk; Schulze-Bahr, Eric; Rolfes, Caroline; Decher, Niels

    2015-04-01

    TASK-1 channels have emerged as promising drug targets against atrial fibrillation, the most common arrhythmia in the elderly. While TASK-3, the closest relative of TASK-1, was previously not described in cardiac tissue, we found a very prominent expression of TASK-3 in right human auricles. Immunocytochemistry experiments of human right auricular cardiomyocytes showed that TASK-3 is primarily localized at the plasma membrane. Single-channel recordings of right human auricles in the cell-attached mode, using divalent-cation-free solutions, revealed a TASK-1-like channel with a single-channel conductance of about 30pS. While homomeric TASK-3 channels were not found, we observed an intermediate single-channel conductance of about 55pS, possibly reflecting the heteromeric channel formed by TASK-1 and TASK-3. Subsequent experiments with TASK-1/TASK-3 tandem channels or with co-expressed TASK-1 and TASK-3 channels in HEK293 cells or Xenopus oocytes, supported that the 55pS channels observed in right auricles have electrophysiological characteristics of TASK-1/TASK-3 heteromers. In addition, co-expression experiments and single-channel recordings suggest that heteromeric TASK-1/TASK-3 channels have a predominant surface expression and a reduced affinity for TASK-1 blockers. In summary, the evidence for heteromeric TASK-1/TASK-3 channel complexes together with an altered pharmacologic response to TASK-1 blockers in vitro is likely to have further impact for studies isolating ITASK-1 from cardiomyocytes and for the development of drugs specifically targeting TASK-1 in atrial fibrillation treatment.

  17. Mild gasification technology development process: Task 3, Bench-scale char upgrading study, February 1988--November 1990

    SciTech Connect

    Carty, R.H.; Onischak, M.; Babu, S.P.; Knight, R.A.; Wootten, J.M.; Duthie, R.G.

    1990-12-01

    The overall objective of this program is to develop mild gasification technology and co-product utilization. The objective of Task 3 was to investigate the necessary steps for upgrading the mild gasification char into potential high-market-value solid products. Recommendations of the Task 1 market survey section formed the basis for selecting three value-added solid products from mild gasification char: form coke, smokeless fuel, and activated adsorbent char. The formation and testing for the form coke co-product involved an evaluation of its briquette strength and reactivity. The measured tensile strength and reactivity of the form coke sample briquettes were in the range of commercial coke, and development tests on a larger scale are recommended. The reaction rate of the form coke carbon with carbon dioxide at 1825{degree}F was measured using a standard procedure. A smokeless fuel briquette with limestone added to control sulfur can be made from mild gasification char in a simple manner. Test results have shown that briquettes with limestone have a heating value comparable to other solid fuels and the limestone can retain up to 88% of the sulfur during combustion in a simple bench-scale combustion test, almost all of it as a stable calcium sulfate. Adsorbent chars were prepared with a standard steam activation procedure and tested for a variety of pertinent property and performance values. Such adsorbents may be better suited for use in some areas, such as the adsorption of low-molecular-weight substances, because of the smaller pore sizes measured in the char. 5 refs., 17 figs., 6 tabs.

  18. Space station data system analysis/architecture study. Task 2: Options development, DR-5. Volume 3: Programmatic options

    NASA Technical Reports Server (NTRS)

    1985-01-01

    Task 2 in the Space Station Data System (SSDS) Analysis/Architecture Study is the development of an information base that will support the conduct of trade studies and provide sufficient data to make design/programmatic decisions. This volume identifies the preferred options in the programmatic category and characterizes these options with respect to performance attributes, constraints, costs, and risks. The programmatic category includes methods used to administrate/manage the development, operation and maintenance of the SSDS. The specific areas discussed include standardization/commonality; systems management; and systems development, including hardware procurement, software development and system integration, test and verification.

  19. The Health Services Mobility Study Method of Task Analysis and Curriculum Design. Research Report No. 11. Volume 3: Using the Computer to Develop Job Ladders.

    ERIC Educational Resources Information Center

    Gilpatrick, Eleanor

    This document is volume 3 of a four-volume report which describes the components of the Health Services Mobility Study (HSMS) method of task analysis, job ladder design, and curriculum development. Divided into four chapters, volume 3 is a manual for using HSMS computer based statistical procedures to design job structures and job ladders. Chapter…

  20. Development of EPA OTM 10 for Landfill Applications, Interim Report

    EPA Science Inventory

    Quantification of greenhouse gas emissions from area sources is of increasing importance. Due to the spatial extent and non homogenous nature of many area sources, assessment of fugitive emissions using traditional point sampling techniques can be problematic. To address this, th...

  1. Development of Mobile Measurement Method Series OTM 33

    EPA Science Inventory

    Starting in 2006, the United States Environmental Protection Agency has explored use of mobile instrumented vehicles for a variety of air quality assessment applications under its Geospatial Measurement of Air Pollution (GMAP) program. GMAP systems utilize next generation, fast-r...

  2. QUEST/Ada (query utility environment for software testing of Ada: The development of a program analysis environment for Ada, task 1, phase 3

    NASA Technical Reports Server (NTRS)

    Brown, David B.

    1991-01-01

    The results of research and development efforts of the first six months of Task 1, Phase 3 of the project are presented. The goals of Phase 3 are: (1) to further refine the rule base and complete the comparative rule base evaluation; (2) to implement and evaluate a concurrency testing prototype; (3) to convert the complete (unit-level and concurrency) testing prototype to a workstation environment; and (4) to provide a prototype development document to facilitate the transfer of research technology to a working environment. These goals were partially met and the results are summarized.

  3. ARL participation in the C4ISR OTM experiment: integration and performance results

    NASA Astrophysics Data System (ADS)

    Zong, Lei; O'Brien, Barry J.

    2007-04-01

    The Command, Control, Communication, Computers, Intelligence, Surveillance and Reconnaissance (C4ISR) On-The- Move (OTM) demonstration is an annual showcase of how innovative technologies can help modern troops increase their situational awareness (SA) in battlefield environments. To evaluate the effectiveness these new technologies have on the soldiers' abilities to gather situational information, the demonstration involves United States Army National Guard troops in realistic war game scenarios at an Army Reserve training ground. The Army Research Laboratory (ARL) was invited to participate in the event, with the objective demonstrating system-level integration of disparate technologies developed for gathering SA information in small unit combat operations. ARL provided expertise in Unattended Ground Sensing (UGS) technology, Unmanned Ground Vehicle (UGV) technology, information processing and wireless mobile ad hoc communication. The ARL C4ISR system included a system of multimodal sensors (MMS), a trip wire imager, a man-portable robotic vehicle (PackBot), and low power sensor radios for communication between an ARL system and a hosting platoon vehicle. This paper will focus on the integration effort of bringing the multiple families of sensor assets together into a working system.

  4. 77 FR 10799 - Revised Guidance for Requesting One-Time Movement (OTM) Approvals

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-23

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF TRANSPORTATION Federal Railroad Administration Revised Guidance for Requesting One-Time Movement (OTM) Approvals AGENCY... Administrator for Railroad Safety/Chief Safety Officer. These approvals are generally referred to as...

  5. The integration of a mesh reflector to a 15-foot box truss structure. Task 3: Box truss analysis and technology development

    NASA Technical Reports Server (NTRS)

    Bachtell, E. E.; Thiemet, W. F.; Morosow, G.

    1987-01-01

    To demonstrate the design and integration of a reflective mesh surface to a deployable truss structure, a mesh reflector was installed on a 15 foot box truss cube. The specific features demonstrated include: (1) sewing seams in reflective mesh; (2) mesh stretching to desired preload; (3) installation of surface tie cords; (4) installation of reflective surface on truss; (5) setting of reflective surface; (6) verification of surface shape/accuracy; (7) storage and deployment; (8) repeatability of reflector surface; and (9) comparison of surface with predicted shape using analytical methods developed under a previous task.

  6. Task Based Language Teaching: Development of CALL

    ERIC Educational Resources Information Center

    Anwar, Khoirul; Arifani, Yudhi

    2016-01-01

    The dominant complexities of English teaching in Indonesia are about limited development of teaching methods and materials which still cannot optimally reflect students' needs (in particular of how to acquire knowledge and select the most effective learning models). This research is to develop materials with complete task-based activities by using…

  7. Development of preliminary design concept for multifunction display and control system for Orbiter crew station. Task 3: Concept analysis

    NASA Technical Reports Server (NTRS)

    Spiger, R. J.; Farrell, R. J.; Holcomb, G. A.

    1982-01-01

    The access schema developed to access both individual switch functions as well as automated or semiautomated procedures for the orbital maneuvering system and electrical power and distribution and control system discussed and the operation of the system is described. Feasibility tests and analyses used to define display parameters and to select applicable hardware choices for use in such a system are presented and the results are discussed.

  8. Marine Animal Alert System -- Task 2.1.5.3: Development of Monitoring Technologies -- FY 2011 Progress Report

    SciTech Connect

    Carlson, Thomas J.; Deng, Zhiqun; Myers, Joshua R.; Matzner, Shari; Copping, Andrea E.

    2011-09-30

    The Marine Animal Alert System (MAAS) in development by the Pacific Northwest National Laboratory is focused on providing elements of compliance monitoring to support deployment of marine hydrokinetic energy devices. An initial focus is prototype tidal turbines to be deployed in Puget Sound in Washington State. The MAAS will help manage the risk of injury or mortality to marine animals from blade strike or contact with tidal turbines. In particular, development has focused on detection, classification, and localization of listed Southern Resident killer whales within 200 m of prototype turbines using both active and passive acoustic approaches. At the close of FY 2011, a passive acoustic system consisting of a pair of four-element star arrays and parallel processing of eight channels of acoustic receptions has been designed and built. Field tests of the prototype system are scheduled for the fourth quarter of calendar year 2011. Field deployment and testing of the passive acoustic prototype is scheduled for the first quarter of FY 2012. The design of an active acoustic system that could be built using commercially available off-the-shelf components from active acoustic system vendors is also in the final stages of design and specification.

  9. How to Develop an Engineering Design Task

    ERIC Educational Resources Information Center

    Dankenbring, Chelsey; Capobianco, Brenda M.; Eichinger, David

    2014-01-01

    In this article, the authors provide an overview of engineering and the engineering design process, and describe the steps they took to develop a fifth grade-level, standards-based engineering design task titled "Getting the Dirt on Decomposition." Their main goal was to focus more on modeling the discrete steps they took to create and…

  10. Solar Concentrator Advanced Development Program, Task 1

    NASA Technical Reports Server (NTRS)

    1986-01-01

    Solar dynamic power generation has been selected by NASA to provide power for the space station. Solar dynamic concentrator technology has been demonstrated for terrestrial applications but has not been developed for space applications. The object of the Solar Concentrator Advanced Development program is to develop the technology of solar concentrators which would be used on the space station. The first task of this program was to develop conceptual concentrator designs and perform trade-off studies and to develop a materials data base and perform material selection. Three unique concentrator concepts; Truss Hex, Spline Radial Panel and Domed Fresnel, were developed and evaluated against weighted trade criteria. The Truss Hex concept was recommended for the space station. Materials data base development demonstrated that several material systems are capable of withstanding extended periods of atomic oxygen exposure without undesirable performance degradation. Descriptions of the conceptual designs and materials test data are included.

  11. Development, social norms, and assignment to task

    PubMed Central

    Fafchamps, Marcel

    2011-01-01

    Economic development involves a structural transformation in the way people are allocated to tasks. There is a shift from self-provision to market exchange, facilitating specialization. There is also a shift from self-employment to wage employment in large firms and organizations, driven by innovation and increasing returns to scale. Changes in allocation mechanisms require changes in norms and attitudes. Because different labor assignment domains coexist, conflicts arise among norms that apply to different domains, possibly resulting in dysfunctional outcomes. I argue that religion, humanism, and schools have all played an important historical role in fostering the changes in social norms and attitudes that are needed to accompany structural changes in the way economies allocate workers to tasks. PMID:22198757

  12. Task Specificity in Early Oral Motor Development

    PubMed Central

    Wilson, Erin M.; Green, Jordan R.; Yunusova, Yana Y.; Moore, Christopher A.

    2009-01-01

    This article addresses a long-standing clinical and theoretical debate regarding the potential relationship between speech and nonspeech behaviors in the developing system. The review is motivated by the high popularity of nonspeech oral motor exercises (NSOMEs), including alimentary behaviors such as chewing, in the treatment of speech disorders in young children. The similarities and differences in the behavioral characteristics, sensory requirements, and task goals for speech and nonspeech oromotor behaviors are compared. Integrated theoretical paradigms and empirical data on the development of early oromotor behaviors are discussed. Although the efficacy of NSOMEs remains empirically untested at this time, studies of typical developmental speech physiology fail to support a theoretical framework promoting the use of NSOMEs. Well-designed empirical studies are necessary, however, to establish the efficacy of NSOMEs for specific clinical population and treatment targets. PMID:19058112

  13. Development of "'Hot" Executive Function: The Children's Gambling Task

    ERIC Educational Resources Information Center

    Kerr, Aurora; Zelazo, Philip David

    2004-01-01

    Development of affective decision-making was studied in 48 children at two ages (3 and 4 years) using a simplified version of the Iowa Gambling Task (Bechara, Damasio, Damasio, & Anderson, 1994). On each of 50 trials, children chose from 1 of 2 decks of cards that, when turned, displayed happy and sad faces, corresponding to rewards (candies) won…

  14. Complete 3D kinematics of upper extremity functional tasks.

    PubMed

    van Andel, Carolien J; Wolterbeek, Nienke; Doorenbosch, Caroline A M; Veeger, DirkJan H E J; Harlaar, Jaap

    2008-01-01

    Upper extremity (UX) movement analysis by means of 3D kinematics has the potential to become an important clinical evaluation method. However, no standardized protocol for clinical application has yet been developed, that includes the whole upper limb. Standardization problems include the lack of a single representative function, the wide range of motion of joints and the complexity of the anatomical structures. A useful protocol would focus on the functional status of the arm and particularly the orientation of the hand. The aim of this work was to develop a standardized measurement method for unconstrained movement analysis of the UX that includes hand orientation, for a set of functional tasks for the UX and obtain normative values. Ten healthy subjects performed four representative activities of daily living (ADL). In addition, six standard active range of motion (ROM) tasks were executed. Joint angles of the wrist, elbow, shoulder and scapula were analyzed throughout each ADL task and minimum/maximum angles were determined from the ROM tasks. Characteristic trajectories were found for the ADL tasks, standard deviations were generally small and ROM results were consistent with the literature. The results of this study could form the normative basis for the development of a 'UX analysis report' equivalent to the 'gait analysis report' and would allow for future comparisons with pediatric and/or pathologic movement patterns.

  15. Advanced Turbine Systems Program conceptual design and product development. Task 3.0, Selection of natural gas-fired Advanced Turbine System

    SciTech Connect

    1994-12-01

    This report presents results of Task 3 of the Westinghouse ATS Phase II program. Objective of Task 3 was to analyze and evaluate different cycles for the natural gas-fired Advanced Turbine Systems in order to select one that would achieve all ATS program goals. About 50 cycles (5 main types) were evaluated on basis of plant efficiency, emissions, cost of electricity, reliability-availability-maintainability (RAM), and program schedule requirements. The advanced combined cycle was selected for the ATS plant; it will incorporate an advanced gas turbine engine as well as improvements in the bottoming cycle and generator. Cost and RAM analyses were carried out on 6 selected cycle configurations and compared to the baseline plant. Issues critical to the Advanced Combined Cycle are discussed; achievement of plant efficiency and cost of electricity goals will require higher firing temperatures and minimized cooling of hot end components, necessitating new aloys/materials/coatings. Studies will be required in combustion, aerodynamic design, cooling design, leakage control, etc.

  16. Development of an advanced, continuous mild gasification process for the production of co-products (Tasks 2, 3, and 4. 1 to 4. 6), Volume 2

    SciTech Connect

    Knight, R.A.; Gissy, J.L.; Onischak, M.; Babu, S.P.; Carty, R.H. ); Duthie, R.G. ); Wootten, J.M. )

    1991-09-01

    Volume 2 contains information on the following topics: (1) Mild Gasification Technology Development: Process Research Unit Tests Using Slipstream Sampling; (2) Bench-Scale Char Upgrading Study; (3) Mild Gasification Technology Development: System Integration Studies. (VC)

  17. Task Analysis in Instructional Program Development. Theoretical Paper No. 52.

    ERIC Educational Resources Information Center

    Bernard, Michael E.

    A review of task analysis procedures beginning with the military training and systems development approach and covering the more recent work of Gagne, Klausmeier, Merrill, Resnick, and others is presented along with a plan for effective instruction based on the review of task analysis. Literature dealing with the use of task analysis in programmed…

  18. Current Status and Tasks in Development of Cable Recycling Technology

    NASA Astrophysics Data System (ADS)

    Ezure, Takashi; Goto, Kazuhiko

    This paper shows current status and tasks in development of cable recycling technology and it’s items to be solved. Electric cable recycle system has been activated especially for copper conductor recycle in Japan. Previously removed cable coverings materials were mainly land filled. But landfill capacity is decreased and limited in recent years, at the same time, recycle technology was highly developed. A cable recycle technology has 4 tasks. (1) Applying new high efficiency separation system instead of electrostatic and gravity methods to classify mixed various kind of plastics materials including recently developed ecological material (ex PE, PVC, Rubber), (2) Removing heavy metal, especially lead from PVC material, (3) Treatment of optical glass fiber core, which has possibility going to be harmful micro particles, and (4) Establishment of social recycle system for electric wire and cable. Taking action for these tasks shall be proceeded under environmentally sensitive technology together with local government, user, manufacturer, and waste-disposal company on cost performance basis.

  19. Economic and Workforce Development. [Final Task Force Report].

    ERIC Educational Resources Information Center

    Howard Community Coll., Columbia, MD.

    This document describes the vision and priorities of Howard Community College's (HCC's) Economic and Workforce Development Task Force. The task force's commission was to identify the long- and short-term skills businesses will demand of the workforce in the Greater Baltimore area and what Howard Community College must do to continue developing…

  20. 76 FR 61371 - All-Hazard Position Task Books for Type 3 Incident Management Teams

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-04

    ... SECURITY Federal Emergency Management Agency All-Hazard Position Task Books for Type 3 Incident Management... comments. SUMMARY: The All-Hazard Position Task Books for Type 3 Incident Management Teams were developed to assist personnel achieve qualifications in the All-Hazard Incident Command System (ICS)...

  1. Recovery. Oxygen Transport Membrane-Based OxyCombustion for CO2 Capture from Power Plants

    SciTech Connect

    Kelly, Sean; Geary, Joan; Chakravrti, Shrikar; Wilson, Jamie; Christie, Max; Peck, John; Li, Juan; Lane, Jonathan; Gonzalez, Javier; Lu, Yunxiang; Biradar, Mahesh; Robinson, Chuck; Lin, Jiefeng; Plonczak, Pawel; Lu, Zigui; Swami, Sadashiv; Stuckert, Ines

    2015-12-22

    This Final report documents and summarizes all of the work performed for the DOE award DE-FC26-07NT43088 during the period from April 2007 - June 2012. This report outlines accomplishments for the following tasks: Task 1 – Process and Systems Engineering, Task 2 – OTM Performance Improvement, Task 3OTM Manufacturing Development, Task 4 - Laboratory Scale Testing and Task 5 – Project Management.

  2. TASK 3: PILOT PLANT GASIFIER TESTING

    SciTech Connect

    Fusselman, Steve

    2015-11-01

    Aerojet Rocketdyne (AR) has developed an innovative gasifier concept incorporating advanced technologies in ultra-dense phase dry feed system, rapid mix injector, and advanced component cooling to significantly improve gasifier performance, life, and cost compared to commercially available state-of-the-art systems. Design, fabrication and initial testing of the pilot plant compact gasifier was completed in 2011 by a development team led by AR. Findings from this initial test program, as well as subsequent gasifier design and pilot plant testing by AR, identified a number of technical aspects to address prior to advancing into a demonstration-scale gasifier design. Key among these were an evaluation of gasifier ability to handle thermal environments with highly reactive coals; ability to handle high ash content, high ash fusion temperature coals with reliable slag discharge; and to develop an understanding of residual properties pertaining to gasification kinetics as carbon conversion approaches 99%. The gasifier did demonstrate the ability to withstand the thermal environments of highly reactive Powder River Basin coal, while achieving high carbon conversion in < 0.15 seconds residence time. Continuous operation with the high ash fusion temperature Xinyuan coal was demonstrated in long duration testing, validating suitability of outlet design as well as downstream slag discharge systems. Surface area and porosity data were obtained for the Xinyuan and Xinjing coals for carbon conversion ranging from 85% to 97%, and showed a pronounced downward trend in surface area per unit mass carbon as conversion increased. Injector faceplate measurements showed no incremental loss of material over the course of these experiments, validating the commercially traceable design approach and supportive of long injector life goals. Hybrid testing of PRB and natural gas was successfully completed over a wide range of natural gas feed content, providing test data to anchor predictions

  3. Robot welding process control development task

    NASA Technical Reports Server (NTRS)

    Romine, Peter L.

    1992-01-01

    The completion of, and improvements made to, the software developed during 1990 for program maintenance on the PC and HEURIKON and transfer to the CYRO, and integration of the Rocketdyne vision software with the CYRO is documented. The new programs were used successfully by NASA, Rocketdyne, and UAH technicians and engineers to create, modify, upload, download, and control CYRO NC programs.

  4. NASA Remediation Technology Collaboration Development Task, Overview and Project Summaries

    NASA Technical Reports Server (NTRS)

    Romeo, James G.

    2014-01-01

    An overview presentation of NASA's Remediation Technology Collaboration Development Task including the following project summaries: in situ groundwater monitor, in situ chemical oxidation, in situ bioremediation, horizontal multi-port well, and high resolution site characterization.

  5. United States Research and Development effort on ITER magnet tasks

    DOE PAGES

    Martovetsky, Nicolai N.; Reierson, Wayne T.

    2011-01-22

    This study presents the status of research and development (R&D) magnet tasks that are being performed in support of the U.S. ITER Project Office (USIPO) commitment to provide a central solenoid assembly and toroidal field conductor for the ITER machine to be constructed in Cadarache, France. The following development tasks are presented: winding development, inlets and outlets development, internal and bus joints development and testing, insulation development and qualification, vacuum-pressure impregnation, bus supports, and intermodule structure and materials characterization.

  6. Task reports on developing techniques for scattering by 3D composite structures and to generate new solutions in diffraction theory using higher order boundary conditions

    NASA Technical Reports Server (NTRS)

    Volakis, John L.

    1991-01-01

    There are two tasks described in this report. First, an extension of a two dimensional formulation is presented for a three dimensional body of revolution. A Fourier series expansion of the vector electric and magnetic fields is employed to reduce the dimensionality of the system, and an exact boundary condition is employed to terminate the mesh. The mesh termination boundary is chosen such that it leads to convolutional boundary operators for low O(n) memory demand. Second, rigorous uniform geometrical theory of diffraction (UTD) diffraction coefficients are presented for a coated convex cylinder simulated with generalized impedance boundary conditions. Ray solutions are obtained which remain valid in the transition region and reduce uniformly those in the deep lit and shadow regions. A uniform asymptotic solution is also presented for observations in the close vicinity of the cylinder.

  7. Task reports on developing techniques for scattering by 3D composite structures and to generate new solutions in diffraction theory using higher order boundary conditions

    NASA Technical Reports Server (NTRS)

    Volakis, John L.

    1990-01-01

    There are two tasks described in this report. First, an extension of a two dimensional formulation is presented for a three dimensional body of revolution. With the introduction of a Fourier expansion of the vector electric and magnetic fields, a coupled two dimensional system is generated and solved via the finite element method. An exact boundary condition is employed to terminate the mesh and the fast fourier transformation is used to evaluate the boundary integrals for low O(n) memory demand when an iterative solution algorithm is used. Second, the diffraction by a material discontinuity in a thick dielectric/ferrite layer is considered by modeling the layer as a distributed current sheet obeying generalized sheet transition conditions (GSTC's).

  8. Is the Go/No-Go Lexical Decision Task Preferable to the Yes/No Task with Developing Readers?

    ERIC Educational Resources Information Center

    Moret-Tatay, Carmen; Perea, Manuel

    2011-01-01

    The lexical decision task is probably the most common laboratory visual word identification task together with the naming task. In the usual setup, participants need to press the "yes" button when the stimulus is a word and the "no" button when the stimulus is not a word. A number of studies have employed this task with developing readers;…

  9. Development of a Consumer Task List and Assessment of Task Importance and Standards for Consumer Education Curricula.

    ERIC Educational Resources Information Center

    Mayer, Kenneth R.

    1979-01-01

    By comparing the perspectives of consumer education teachers and selected consumers on task importance and minimum task standards for high school graduates, the relative importance of task performance and task standards was ascertained. The results were recommended to be used in the development and refinement of consumer education programs. (JH)

  10. Task 3 -- Bench-scale char upgrading and utilization study

    SciTech Connect

    Jha, M.C.; McCormick, R.L.

    1989-08-02

    This report describes the results of the bench-scale char upgrading study conducted as Task 3 of Development of an Advanced, Continuous Mild Gasification Process for the Production of Coproducts. A process where the char is gasified to produce methane in a first stage reactor was investigated. This methane is then decomposed to produce carbon and hydrogen for recycle in a second stage. The results indicate that both reaction steps are feasible using mild gasification char as the starting feedstock. Conditions for methanation are 700 to 800 C and 200 to 400 psig. Carbon formation conditions are 1,200 to 1,400 C at atmospheric pressure. The carbon produced has properties similar to those of carbons which are commercially marketed as carbon black.

  11. CERAMIC MEMBRANE ENABLING TECHNOLOGY FOR IMPROVED IGCC EFFICIENCY

    SciTech Connect

    Ravi Prasad

    2004-03-31

    This quarterly technical progress report will summarize work accomplished for Phase 2 Program during the quarter January to March 2004. In task 1 OTM development has led to improved strength and composite design for lower temperatures. In task 2, the measurement system of OTM element dimensions was improved. In task 3, a 10-cycle test of a three-tube submodule was reproduced successfully. In task 5, sizing of several potential heat recovery systems was initiated. In task 7, advanced OTM and cryogenic IGCC cases for near-term integration were developed.

  12. Self-calibration of cone-beam CT geometry using 3D-2D image registration: development and application to tasked-based imaging with a robotic C-arm

    NASA Astrophysics Data System (ADS)

    Ouadah, S.; Stayman, J. W.; Gang, G.; Uneri, A.; Ehtiati, T.; Siewerdsen, J. H.

    2015-03-01

    Purpose: Robotic C-arm systems are capable of general noncircular orbits whose trajectories can be driven by the particular imaging task. However obtaining accurate calibrations for reconstruction in such geometries can be a challenging problem. This work proposes a method to perform a unique geometric calibration of an arbitrary C-arm orbit by registering 2D projections to a previously acquired 3D image to determine the transformation parameters representing the system geometry. Methods: Experiments involved a cone-beam CT (CBCT) bench system, a robotic C-arm, and three phantoms. A robust 3D-2D registration process was used to compute the 9 degree of freedom (DOF) transformation between each projection and an existing 3D image by maximizing normalized gradient information with a digitally reconstructed radiograph (DRR) of the 3D volume. The quality of the resulting "self-calibration" was evaluated in terms of the agreement with an established calibration method using a BB phantom as well as image quality in the resulting CBCT reconstruction. Results: The self-calibration yielded CBCT images without significant difference in spatial resolution from the standard ("true") calibration methods (p-value >0.05 for all three phantoms), and the differences between CBCT images reconstructed using the "self" and "true" calibration methods were on the order of 10-3 mm-1. Maximum error in magnification was 3.2%, and back-projection ray placement was within 0.5 mm. Conclusion: The proposed geometric "self" calibration provides a means for 3D imaging on general noncircular orbits in CBCT systems for which a geometric calibration is either not available or not reproducible. The method forms the basis of advanced "task-based" 3D imaging methods now in development for robotic C-arms.

  13. Feasibility study of an Integrated Program for Aerospace-vehicle Design (IPAD) system. Volume 6: Implementation schedule, development costs, operational costs, benefit assessment, impact on company organization, spin-off assessment, phase 1, tasks 3 to 8

    NASA Technical Reports Server (NTRS)

    Garrocq, C. A.; Hurley, M. J.; Dublin, M.

    1973-01-01

    A baseline implementation plan, including alternative implementation approaches for critical software elements and variants to the plan, was developed. The basic philosophy was aimed at: (1) a progressive release of capability for three major computing systems, (2) an end product that was a working tool, (3) giving participation to industry, government agencies, and universities, and (4) emphasizing the development of critical elements of the IPAD framework software. The results of these tasks indicate an IPAD first release capability 45 months after go-ahead, a five year total implementation schedule, and a total developmental cost of 2027 man-months and 1074 computer hours. Several areas of operational cost increases were identified mainly due to the impact of additional equipment needed and additional computer overhead. The benefits of an IPAD system were related mainly to potential savings in engineering man-hours, reduction of design-cycle calendar time, and indirect upgrading of product quality and performance.

  14. Organisational and Task Factors Influencing Teachers' Professional Development at Work

    ERIC Educational Resources Information Center

    Evers, Arnoud T.; Van der Heijden, Béatrice I. J. M.; Kreijns, Karel

    2016-01-01

    Purpose: The purpose of this paper is to investigate organisational (cultural and relational) and task factors which potentially enhance teachers' professional development at work (TPD at Work). The development of lifelong learning competencies and, consequently, the careers of teachers, has become a permanent issue on the agenda of schools…

  15. Application of Task Inventories for Vocational Curricula Development.

    ERIC Educational Resources Information Center

    Conter, Robert V.; Nash, Peg

    A project was undertaken to identify common skill and knowledge competencies in various occupational areas in order to provide vocational instructors and administrators with an up-to-date skill analysis for use in curriculum development. To compile this data base, researchers developed task surveys to determine the minimum competencies needed by…

  16. Development of an integrated in-situ remediation technology. Draft topical report for Task {number_sign}3.3 entitled, ``Iron dechlorination studies`` (September 26, 1994--August 31, 1997)

    SciTech Connect

    Orth, R.; Dauda, T.; McKenzie, D.E.

    1997-11-01

    Contamination in low-permeability soils poses a significant technical challenge to in-situ remediation efforts. Poor accessibility to the contaminants and difficulty in delivery of treatment reagents have rendered existing in-situ treatments such as bioremediation, vapor extraction, and pump and treat rather ineffective when applied to low permeability soils present at many contaminated sites. The technology is an integrated in-situ treatment in which established geotechnical methods are used to install degradation zones directly in the contaminated soil and electro-osmosis is utilized to move the contaminants back and forth through those zones until the treatment is completed. The present Topical Report for Task {number_sign}3.3 summarizes the iron dechlorination research conducted by Monsanto Company.

  17. Comprehensive Career Development for Illinois: Findings and Recommendations of the Illinois Career Development Task Force

    ERIC Educational Resources Information Center

    Williams, J. Mark; Bragg, Debra D.; Makela, Julia Panke

    2008-01-01

    This report summarizes major findings and recommendations of the Illinois Career Development Task Force. The first section provides background information on Task Force formation, membership, meetings, and discussion topics. The second section defines career development, based on the consensus-building process employed by the Task Force, and…

  18. Review of surface-modification programs in the DOE-OTM Tribology Program

    SciTech Connect

    Fenske, G.R.; Nichols, F.A.

    1991-02-01

    The use of surface-modification treatments is a widely accepted practice to reduce the wear and modify the friction behavior of surface regions while maintaining desirable bulk properties (e.g., strength, hardness, thermal conductivity, etc.) of the underlying substrate. These treatments range from conventional diffusion processes such as carburizing steels for case-hardening gears, to advanced non-equilibrium processes such as ion implantation or ion plating. The objective of this task area is to develop and investigate new or emerging surface-modification processes that show a potential for improving and controlling the tribological behavior of surfaces and thus permit engineers to design components for advanced heat engines based on desired bulk properties and near-surface tribological properties.

  19. 3Ps, Task-Based Learning, and the Japanese Learner.

    ERIC Educational Resources Information Center

    Tanasarnsanee, Mika

    2002-01-01

    Summarizes the findings of a work in progress that attempted to investigate to what extent task-based learning was more effective than the 3Ps approach in the teaching of Japanese as a foreign language in Thailand. (Author/VWL)

  20. Development of an integrated in-situ remediation technology. Topical report for Task {number_sign}3.2 entitled, ``Modeling and iron dechlorination studies`` (September 26, 1994--August 31, 1997)

    SciTech Connect

    Shapiro, A.P.; Sivavec, T.M.; Principe, J.M.

    1997-11-01

    Contamination in low-permeability soils poses a significant technical challenge to in-situ remediation efforts. Poor accessibility to the contaminants and difficulty in delivery of treatment reagents have rendered existing in-situ treatments such as bioremediation, vapor extraction, and pump and treat rather ineffective when applied to low-permeability soils present at many contaminated sites. The technology is an integrated in-situ treatment in which established geotechnical methods are used to install degradation zones directly in the contaminated soil, and electro-osmosis is utilized to move the contaminants back and forth through those zones until the treatment is complete. The present Topical Report for Task {number_sign}3.2 summarizes the modeling and dechlorination research conducted by General Electric Research and Development.

  1. Using Modeling Tasks to Facilitate the Development of Percentages

    ERIC Educational Resources Information Center

    Shahbari, Juhaina Awawdeh; Peled, Irit

    2016-01-01

    This study analyzes the development of percentages knowledge by seventh graders given a sequence of activities starting with a realistic modeling task, in which students were expected to create a model that would facilitate the reinvention of percentages. In the first two activities, students constructed their own pricing model using fractions and…

  2. Psychosocial Aspects of Nuclear Developments. Task Force Report 20.

    ERIC Educational Resources Information Center

    American Psychiatric Association, Washington, DC.

    This is the report of a task force formed to bring psychological understanding to bear on the various aspects of the development of nuclear arms and nuclear energy and the threat they pose to human physical, mental, and emotional health. The first of seven articles considers the sociopsychological aspects of the nuclear arms race. Other articles…

  3. Is the go/no-go lexical decision task preferable to the yes/no task with developing readers?

    PubMed

    Moret-Tatay, Carmen; Perea, Manuel

    2011-09-01

    The lexical decision task is probably the most common laboratory visual word identification task together with the naming task. In the usual setup, participants need to press the "yes" button when the stimulus is a word and the "no" button when the stimulus is not a word. A number of studies have employed this task with developing readers; however, error rates and/or response times tend to be quite high. One way to make the task easier for young readers is by employing a go/no-go procedure: "If word, press 'yes'; if not, refrain from responding." Here we conducted a lexical decision experiment that systematically compared the yes/no and go/no-go variants of the lexical decision task with developing readers (second- and fourth-grade children). Results showed that (a) error rates for words and nonwords were much lower in the go/no-go task than in the yes/no task, (b) lexical decision times were substantially faster in the go/no-go task, and (c) there was less variability in the latency data of the go/no-go task for high-frequency words. Thus, the go/no-go lexical decision task is preferable to the "standard" yes/no task when conducting experiments with developing readers.

  4. Space station data system analysis/architecture study. Task 3: Trade studies, DR-5, volume 2

    NASA Technical Reports Server (NTRS)

    1985-01-01

    Results of a Space Station Data System Analysis/Architecture Study for the Goddard Space Flight Center are presented. This study, which emphasized a system engineering design for a complete, end-to-end data system, was divided into six tasks: (1); Functional requirements definition; (2) Options development; (3) Trade studies; (4) System definitions; (5) Program plan; and (6) Study maintenance. The Task inter-relationship and documentation flow are described. Information in volume 2 is devoted to Task 3: trade Studies. Trade Studies have been carried out in the following areas: (1) software development test and integration capability; (2) fault tolerant computing; (3) space qualified computers; (4) distributed data base management system; (5) system integration test and verification; (6) crew workstations; (7) mass storage; (8) command and resource management; and (9) space communications. Results are presented for each task.

  5. Development of additional tasks for the executive function performance test.

    PubMed

    Hahn, Bridget; Baum, Carolyn; Moore, Jennifer; Ehrlich-Jones, Linda; Spoeri, Susan; Doherty, Meghan; Wolf, Timothy J

    2014-01-01

    OBJECTIVE. The Executive Function Performance Test (EFPT) is a reliable and valid performance-based assessment of executive function for people with stroke. The objective of this study was to enhance the clinical utility of the EFPT by developing and testing additional tasks for the EFPT in the Alternate EFPT (aEFPT). METHOD. We performed a cross-sectional study with poststroke participants (n = 25) and healthy control participants (n = 25). All participants completed a neuropsychological assessment battery and both the EFPT and the aEFPT. RESULTS. No statistically significant differences were found between the EFPT and the aEFPT when examining total scores, construct scores, and two overall task scores. Correlations between the aEFPT and the neuropsychological measures were adequate to strong (r2s = .59-.83). CONCLUSION. The aEFPT tasks are comparable to the original EFPT tasks, providing occupational therapy practitioners with additional tasks that can be used clinically to identify performance-based executive function deficits in people with stroke. PMID:25397771

  6. CERAMIC MEMBRANE ENABLING TECHNOLGOY FOR IMPROVED IGCC EFFICIENCY

    SciTech Connect

    Ravi Prasad

    2003-07-01

    This quarterly technical progress report will summarize work accomplished for Phase 2 Program during the quarter April to June 2003. In task 1 OTM development has led to improved flux and strength performance. In task 2, robust PSO1d elements have been fabricated for testing in the pilot reactor. In task 3, the lab-scale pilot reactor has been operated for 1000 hours with improved success. In task 7, economic models substantial benefit of OTM IGCC over CRYO based oxygen production.

  7. Composite Overwrapped Pressure Vessels: Database Extension Task 3.0 and Impact Damage Effects Control Task 8.0

    NASA Technical Reports Server (NTRS)

    Beeson, Harold D.; Davis, Dennis D.; Ross, William L., Sr.; Tapphorn, Ralph M.

    2002-01-01

    This document represents efforts accomplished at the NASA Johnson Space Center White Sands Test Facility (WSTF) in support of the Enhanced Technology for Composite Overwrapped Pressure Vessels (COPV) Program, a joint research and technology effort among the U.S. Air Force, NASA, and the Aerospace Corporation. WSTF performed testing for several facets of the program. Testing that contributed to the Task 3.0 COPV database extension objective included baseline structural strength, failure mode and safe-life, impact damage tolerance, sustained load/impact effect, and materials compatibility. WSTF was also responsible for establishing impact protection and control requirements under Task 8.0 of the program. This included developing a methodology for establishing an impact control plan. Seven test reports detail the work done at WSTF. As such, this document contributes to the database of information regarding COPV behavior that will ensure performance benefits and safety are maintained throughout vessel service life.

  8. Task group to develop list of environmental standards

    NASA Astrophysics Data System (ADS)

    A new task group designed to develop a list of existing and potential standards that are applicable to environmental contamination problems in soil, rock, and groundwater has been established by the American Society for Testing a n d Materials (ASTM) Subcommittee on Geotechnics of Waste Management. The list currently includes over 60 existing and draft ASTM standards from ASTM committees in the areas of site characterization, construction evaluation, and geosynthetics.

  9. Development and experimentation of an eye/brain/task testbed

    NASA Technical Reports Server (NTRS)

    Harrington, Nora; Villarreal, James

    1987-01-01

    The principal objective is to develop a laboratory testbed that will provide a unique capability to elicit, control, record, and analyze the relationship of operator task loading, operator eye movement, and operator brain wave data in a computer system environment. The ramifications of an integrated eye/brain monitor to the man machine interface are staggering. The success of such a system would benefit users of space and defense, paraplegics, and the monitoring of boring screens (nuclear power plants, air defense, etc.)

  10. The Development and Implementation of Task-Based Writing Performance Assessment for Japanese Learners of English

    ERIC Educational Resources Information Center

    Sugita, Yoshihito

    2009-01-01

    The main purpose of this research is 1) to establish a framework for the test development and the constructs of writing performance test, 2) to implement a developed writing performance assessment, and 3) to examine the degree of reliability and validity of the assessment tasks and rating scales. Construct-based processing approach to testing…

  11. Distinguishing Schemes and Tasks in Children's Development of Multiplicative Reasoning

    ERIC Educational Resources Information Center

    Tzur, Ron; Johnson, Heather L.; McClintock, Evan; Kenney, Rachael H.; Xin, Yan P.; Si, Luo; Woordward, Jerry; Hord, Casey; Jin, Xianyan

    2013-01-01

    We present a synthesis of findings from constructivist teaching experiments regarding six schemes children construct for reasoning multiplicatively and tasks to promote them. We provide a task-generating platform game, depictions of each scheme, and supporting tasks. Tasks must be distinguished from children's thinking, and learning situations…

  12. 78 FR 70087 - Interagency Task Force on Veterans Small Business Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-11-22

    ... ADMINISTRATION Interagency Task Force on Veterans Small Business Development AGENCY: U.S. Small Business Administration. ACTION: Notice of open Federal Interagency Task Force meeting. SUMMARY: The SBA is issuing this... meeting of the Interagency Task Force on Veterans Small Business Development. The Task Force...

  13. 78 FR 21492 - Interagency Task Force on Veterans Small Business Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-10

    ... ADMINISTRATION Interagency Task Force on Veterans Small Business Development AGENCY: U.S. Small Business Administration. ACTION: Notice of open Federal Interagency Task Force Meeting. SUMMARY: The SBA is issuing this... meeting of the Interagency Task Force on Veterans Small Business Development. The Task Force...

  14. Task Complexity, Focus on Form, and Second Language Development

    ERIC Educational Resources Information Center

    Revesz, Andrea

    2009-01-01

    Tasks have received increased attention in SLA research for the past decade, as has the role of focus on form. However, few empirical studies have investigated the relationship among tasks, focus-on-form techniques, and second language (L2) learning outcomes. To help address this gap, the present study examined how the task variable +/- contextual…

  15. Task Engagement: A Turning Point in Foreign Language Development.

    ERIC Educational Resources Information Center

    Platt, Elizabeth J.; Brooks, Frank B.

    2002-01-01

    Uses a sociocultural framework to suggest task engagement as a viable construct in second language learning research. Examines second language learner data to identify task engagement as it emerges, unfolds in dialogic activity, and becomes associated with he transformation of task, self, and group. (Author/VWL)

  16. The Classification of Children's Knowledge: Development on the Balance-Scale and Inclined-Plane Tasks.

    ERIC Educational Resources Information Center

    Ferretti, Ralph P.; And Others

    1985-01-01

    Applies to the inclined-plane task Siegler's (1981) observation that performance on Piagetian tasks is governed by similar rule structures. Also replicates Siegler's original observations about the development on the balance-scale task and determines the consistency in children's rule usage across tasks. (Author/AS)

  17. ADVANCED OXYFUEL BOILERS AND PROCESS HEATERS FOR COST EFFECTIVE CO2 CAPTURE AND SEQUESTRATION

    SciTech Connect

    Max Christie; Rick Victor; Juan Li; Bart Van Hassel

    2005-12-31

    This annual technical progress report summarizes the work accomplished during the third year of the program, January-December 2005, in the following task areas: Task 1--Conceptual Design, Task 2--Laboratory Scale Evaluations, Task 3--OTM Development, Task 4--Economic Evaluation and Commercialization Planning and Task 5--Program Management.

  18. Retrieval process development and enhancements project Fiscal year 1995: Simulant development technology task progress report

    SciTech Connect

    Golcar, G.R.; Bontha, J.R.; Darab, J.G.

    1997-01-01

    The mission of the Retrieval Process Development and Enhancements (RPD&E) project is to develop an understanding of retrieval processes, including emerging and existing technologies, gather data on these technologies, and relate the data to specific tank problems such that end-users have the requisite technical bases to make retrieval and closure decisions. The development of waste simulants is an integral part of this effort. The work of the RPD&E simulant-development task is described in this document. The key FY95 accomplishments of the RPD&E simulant-development task are summarized below.

  19. Language Mediation in an L3 Classroom: The Role of Task Modalities and Task Types

    ERIC Educational Resources Information Center

    Payant, Caroline; Kim, YouJin

    2015-01-01

    Pedagogical tasks in language learning settings promote learner-learner interaction and provide second language (L2) learners with opportunities to process authentic input and produce output (Philp, Adams, & Iwashita, 2014). During these interactions, learners use their language repertoire to mediate their output (Swain & Lapkin, 2000).…

  20. Management Skills. Skills Task Force Research Paper 3.

    ERIC Educational Resources Information Center

    Johnson, Steven; Winterton, Jonathan

    A task force was convened to identify the nature, extent, and pattern of skill needs and shortages for managerial occupations in the United Kingdom (UK). The task force began by examining the key challenges facing managers in the UK. The following factors were among those considered: economic policies promoting liberalization and deregulation;…

  1. In situ sampling device development engineering task plan

    SciTech Connect

    DeFord, D.K.

    1994-10-07

    This engineering task plan (ETP) supports the development for facility use of an improved packaging method or device for the sorbent media used during in situ sampling of waste tanks. Improvement is being sought due to problems with internal and external radioactive contamination. In situ sampling refers to placing sample collection media (primarily sorbent tubes) directly into the tank headspace, then drawing tank gases through the collection media to obtain samples. Development for facility use, includes design, fabrication, and formal documentation of the device. As the most important change to be made is addition of a High Efficiency Particulate Air (HEPA) filter, the device will be referred to in this ETP as the Filter Device or simply the Device. This ETP is intended to be the management plan governing the design, fabrication, and formal documentation of the Filter Device. This plan identifies the engineering services and other resources to accomplish that purpose. The design basis for the development of the Device is presented in this ETP.

  2. Engineering development of selective agglomeration: Task 5, Bench- scale process testing

    SciTech Connect

    Not Available

    1991-09-01

    Under the overall objectives of DOE Contract ``Engineering Development of Selective Agglomeration,`` there were a number of specific objectives in the Task 5 program. The prime objectives of Task 5 are highlighted below: (1) Maximize process performance in pyritic sulfur rejection and BTU recovery, (2) Produce a low ash product, (3) Compare the performance of the heavy agglomerant process based on diesel and the light agglomerant process using heptane, (4) Define optimum processing conditions for engineering design, (5) Provide first-level evaluation of product handleability, and (6) Explore and investigate process options/ideas which may enhance process performance and/or product handleability.

  3. Engineering development of selective agglomeration: Task 5, Bench- scale process testing

    SciTech Connect

    Not Available

    1991-09-01

    Under the overall objectives of DOE Contract Engineering Development of Selective Agglomeration,'' there were a number of specific objectives in the Task 5 program. The prime objectives of Task 5 are highlighted below: (1) Maximize process performance in pyritic sulfur rejection and BTU recovery, (2) Produce a low ash product, (3) Compare the performance of the heavy agglomerant process based on diesel and the light agglomerant process using heptane, (4) Define optimum processing conditions for engineering design, (5) Provide first-level evaluation of product handleability, and (6) Explore and investigate process options/ideas which may enhance process performance and/or product handleability.

  4. Initial development of an automated task analysis profiling system

    SciTech Connect

    Jorgensen, C.C.

    1984-01-01

    A program for automated task analysis is described. Called TAPS (task analysis profiling system), the program accepts normal English prose and outputs skills, knowledges, attitudes, and abilities (SKAAs) along with specific guidance and recommended ability measurement tests for nuclear power plant operators. A new method for defining SKAAs is presented along with a sample program output.

  5. Individual Differences and Development in Water-Level Task Performance.

    ERIC Educational Resources Information Center

    Thomas, Hoben; Turner, Geoffrey, F. W.

    1991-01-01

    Presents research on individuals' ability to perform Piaget's water-level task. At almost every age and for each sex, some subjects had high probability of success and some had low. Age-related improvement was not a result of children's increasing accuracy in task performance. Differences in performance between sexes were evident at all ages.…

  6. San Joaquin River Up-Stream DO TMDL Project Task 4: MonitoringStudy Interim Task Report #3

    SciTech Connect

    Stringfellow, William; Borglin, Sharon; Dahlgren, Randy; Hanlon,Jeremy; Graham, Justin; Burks, Remie; Hutchinson, Kathleen

    2007-03-30

    Lander Avenue.This data is specifically being collected to provide data for the Task 6Modeling effort. Task 4 provides input and calibration data for flow andWQ modeling associated with the low DO problems in the SJR watershed,including modeling on the linkage among nutrients, algae, and low DO.Task 4 is providing a higher volume of high quality and coherent data tothe modeling team than was available in the past for the upstream SJR.The monitoring and research activities under Task 4 are integrated withthe Modeling effort (Task 6) and are not designed to be a stand aloneprogram. Although, the majority of analysis of the Task 4 data isoccurring as part of the Task 6 Modeling program, analysis of Task 4 dataindependently of the modeling effort is also an important component ofthe DO TMDL Project effort. In this report, we present the results ofmonitoring and research conducted under Task 4. The major purposes ofthis report are to 1) document activities undertaken as part of theDOTMDL Project; 2) organize electronic data for delivery to Stateagencies, stakeholders and principal investigators (cooperators) on theDO TMDL Project; 3) provide a summary analysis of the data for referenceand to assist stakeholders in planning watershed activities inresponse tothe DO TMDL requirements; and 5) provide a preliminary scientificinterpretation independently of the Task 6 Modeling effort. Due to theextensive scope of theTask 4 portion of the DO TMDL Project, the Task 4March 2007 Interim Report is divided into a numbers of chapters andassociated appendixes designed to be able to stand1-3 independently ofeach other. The purpose of this chapter is to provide an overview of Task4 data collection and to explain the structure of the overallreport.

  7. Development of an advanced, continuous mild gasification process for the production of co-products (Tasks 2, 3, and 4.1 to 4.6), Volume 2. Final report

    SciTech Connect

    Knight, R.A.; Gissy, J.L.; Onischak, M.; Babu, S.P.; Carty, R.H.; Duthie, R.G.; Wootten, J.M.

    1991-09-01

    Volume 2 contains information on the following topics: (1) Mild Gasification Technology Development: Process Research Unit Tests Using Slipstream Sampling; (2) Bench-Scale Char Upgrading Study; (3) Mild Gasification Technology Development: System Integration Studies. (VC)

  8. 78 FR 23970 - Interagency Task Force on Veterans Small Business Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-23

    ... ADMINISTRATION Interagency Task Force on Veterans Small Business Development AGENCY: U.S. Small Business Administration. ACTION: Notice of open Federal Interagency Task Force Meeting. SUMMARY: This document corrects the SBA's Interagency Task Force on Veterans Small Business Developments notice of a public...

  9. Task analysis method for procedural training curriculum development.

    PubMed

    Riggle, Jakeb D; Wadman, Michael C; McCrory, Bernadette; Lowndes, Bethany R; Heald, Elizabeth A; Carstens, Patricia K; Hallbeck, M Susan

    2014-06-01

    A central venous catheter (CVC) is an important medical tool used in critical care and emergent situations. Integral to proper care in many circumstances, insertion of a CVC introduces the risk of central line-associated blood stream infections and mechanical adverse events; proper training is important for safe CVC insertion. Cognitive task analysis (CTA) methods have been successfully implemented in the medical field to improve the training of postgraduate medical trainees, but can be very time-consuming to complete and require a significant time commitment from many subject matter experts (SMEs). Many medical procedures such as CVC insertion are linear processes with well-documented procedural steps. These linear procedures may not require a traditional CTA to gather the information necessary to create a training curriculum. Accordingly, a novel, streamlined CTA method designed primarily to collect cognitive cues for linear procedures was developed to be used by medical professionals with minimal CTA training. This new CTA methodology required fewer trained personnel, fewer interview sessions, and less time commitment from SMEs than a traditional CTA. Based on this study, a streamlined CTA methodology can be used to efficiently gather cognitive information on linear medical procedures for the creation of resident training curricula and procedural skills assessments. PMID:24366759

  10. Assessment Engineering Task Model Maps, Task Models and Templates as a New Way to Develop and Implement Test Specifications

    ERIC Educational Resources Information Center

    Luecht, Richard M.

    2013-01-01

    Assessment engineering is a new way to design and implement scalable, sustainable and ideally lower-cost solutions to the complexities of designing and developing tests. It represents a merger of sorts between cognitive task modeling and engineering design principles--a merger that requires some new thinking about the nature of score scales, item…

  11. Development of Interpersonal Coordination between Peers during a Drumming Task

    ERIC Educational Resources Information Center

    Endedijk, Hinke M.; Ramenzoni, Veronica C. O.; Cox, Ralf F. A.; Cillessen, Antonius H. N.; Bekkering, Harold; Hunnius, Sabine

    2015-01-01

    During social interaction, the behavior of interacting partners becomes coordinated. Although interpersonal coordination is well-studied in adults, relatively little is known about its development. In this project we explored how 2-, 3-, and 4-year-old children spontaneously coordinated their drumming with a peer. Results showed that all children…

  12. Development of a task analysis tool to facilitate user interface design

    NASA Technical Reports Server (NTRS)

    Scholtz, Jean C.

    1992-01-01

    A good user interface is one that facilitates the user in carrying out his task. Such interfaces are difficult and costly to produce. The most important aspect in producing a good interface is the ability to communicate to the software designers what the user's task is. The Task Analysis Tool is a system for cooperative task analysis and specification of the user interface requirements. This tool is intended to serve as a guide to development of initial prototypes for user feedback.

  13. Apparent response incompatibility effects on P3 latency depend on the task.

    PubMed

    Pfefferbaum, A; Christensen, C; Ford, J M; Kopell, B S

    1986-11-01

    Ten young women were tested with an ERP paradigm that used the words 'left,' 'right,' 'LEFT,' 'RIGHT' as stimuli. The stimulus sequence was presented as several separate runs with varying response instructions. Subjects were instructed to respond according to the meaning of the stimulus in the (WORD task), to the case in which the stimulus was written (CASE task), or to both the case and meaning of the stimulus (CASE/WORD) task. In each task, half the trials called for a response that was incompatible with the stimulus. For the WORD task, compatible and incompatible trials were presented as separate blocks of trials. For all 3 tasks an additional stimulus sequence was presented in which the words were degraded with superimposed visual random noise. Reaction time (RT) in the CASE/WORD task was more than 100 msec later than in the other tasks. In the WORD and CASE/WORD tasks, RT was delayed more than 100 msec when the response was incompatible with the stimulus. Degrading the stimulus additionally delayed RT by about 100 msec. In the WORD and CASE tasks, error RTs were earlier than correct RTs. P3 latency was measured with a single-trial latency adjustment algorithm. P3 latency was delayed in the CASE/WORD task compared to the other 2 tasks. P3 was delayed by degrading the stimuli. Contrary to some previous reports, P3 was delayed by about 70 msec when incompatible responses were required, but only in the WORD task. Taken together with error and RT data, these P3 latency data are consistent with the notion that the task causes subjects to adopt different strategies and hence different types of processing (i.e., serial vs. parallel). Depending on the type of processing, P3 may appear to be affected by response incompatibility.

  14. Task 21 - Development of Systems Engineering Applications for Decontamination and Decommissioning Activities

    SciTech Connect

    Erickson, T.A.

    1998-11-01

    The objectives of this task are to: Develop a model (paper) to estimate the cost and waste generation of cleanup within the Environmental Management (EM) complex; Identify technologies applicable to decontamination and decommissioning (D and D) operations within the EM complex; Develop a database of facility information as linked to project baseline summaries (PBSs). The above objectives are carried out through the following four subtasks: Subtask 1--D and D Model Development, Subtask 2--Technology List; Subtask 3--Facility Database, and Subtask 4--Incorporation into a User Model.

  15. Household task participation of children and adolescents with cerebral palsy, Down syndrome and typical development.

    PubMed

    Amaral, Maíra Ferreira do; Drummond, Adriana de França; Coster, Wendy J; Mancini, Marisa Cotta

    2014-02-01

    This cross-sectional study compared patterns of household task participation (e.g., performance, assistance and independence) of youth with cerebral palsy (CP), Down syndrome (DS) and typical development (TD). Parents of 75 children and adolescents were interviewed to report on their youths' active engagement in daily self-care and family-care tasks, using the children helping out: responsibilities, expectations and supports (CHORES) questionnaire. Groups were equivalent in age (mean=9.3 years; SD=2.2 years), sex (male=39; female=36), respondent education, presence of maid, and number of siblings at home, but differed on child cognitive function and family socioeconomic status, with the DS and the CP groups scoring lower than the TD group but not different from each other. ANOVA revealed group differences on CHORES performance of self-care tasks (p=0.004), on total participation score (p=0.04) and on assistance scores (p<0.02). Post hoc comparisons showed that TD group scored higher than CP and DS groups on performance and assistance in self-care tasks and total assistance; TD and CP groups were similar on total performance and assistance in family-care tasks. The groups also differed on independence indices; the TD index was greater than the CP and DS, and the CP index was greater than the DS. Parents from the three groups did not differ on ratings of importance regarding their children's household participation (p=0.416). In spite of observed differences, children and adolescents with CP and DS are actively engaged in daily self-care and family-care tasks; their participation at home is not prevented by the presence of their disabilities.

  16. Task Level Job Performance Criteria Development. Final Report.

    ERIC Educational Resources Information Center

    Wiley, Llewellyn N.; Hahn, Clifford P.

    This study investigated possibilities for improving identification of job performance requirements by examining job incumbent's performance on separate tasks. Three specialties were studied: 291X0, Telecommunications Operation Specialist; 304X4, Group Radio Communications Equipment Repairman; and 431X1C, Aircraft Maintenance Specialist.…

  17. Career Development, Collective Efficacy, and Individual Task Performance

    ERIC Educational Resources Information Center

    Kellett, Janet B.; Humphrey, Ronald H.; Sleeth, Randall G.

    2009-01-01

    Purpose: The purpose of this paper is to test the hypothesis that perceived collective efficacy would mediate the effects of self-efficacy on individual task performance. Design/methodology/approach: An assessment center design with 147 participants in 49 three-person groups was used. Findings: It is found that for individuals working on an…

  18. Developing Intentionality and L2 Classroom Task-Engagement

    ERIC Educational Resources Information Center

    Stelma, Juup

    2014-01-01

    This paper extends work on "intentionality", from philosophy, psychology and education to an exploration of learners' meaning-making in L2 classroom task-engagement. The paper draws on both phenomenological and folk-psychological perspectives on intentionality, and employs John R. Searle's intrinsic (mental) and derived (observable)…

  19. Changes in oxygen sensitivity of TASK in carotid body glomus cells during early postnatal development

    PubMed Central

    Kim, Donghee; Papreck, Justin R.; Kim, Insook; Donnelly, David F.; Carroll, John L.

    2011-01-01

    A post-natal increase in carotid body (CB) hypoxia responsiveness occurs at the level of carotid sinus nerve activity, intracellular calcium, cell membrane depolarization and hypoxic inhibition of O2-sensitive background K+ conductance. TASK-1, TASK-1/3 and TASK-3 are functionally expressed in CB glomus cells, with TASK-1/3 providing the major part of the O2-sensitive TASK-like background K+ conductance. Here we report the effects of graded hypoxia on TASK-like channel activity in CB glomus cells from rats aged 0-1, 6-7 and 16-18 days; the time frame of postnatal CB functional maturation. TASK was active in nearly all cell-attached patches and TASK activity during normoxia did not differ across ages. Hypoxia produced a progressive decrease in channel opening frequency with graded decreases in O2 level and also produced glomus cell depolarization, as assessed by the shift in reversal potential of TASK single channel current. Hypoxic inhibition of TASK activity was least at P0-P1 and increased with age mainly between 6-7 and 16-18 days. The O2-sensitive TASK activity was significantly greater in glomus cells from P16-P18 when compared to cells from P0-P1 day old rats. These results support the hypothesis that postnatal carotid body functional maturation is due, at least in part, to changes in the sensitivity of TASK to the hypoxic signals generated in glomus cells. PMID:21530688

  20. ADVANCED OXYFUEL BOILERS AND PROCESS HEATERS FOR COST EFFECTIVE CO2 CAPTURE AND SEQUESTRATION

    SciTech Connect

    John Sirman; Leonard Switzer; Bart van Hassel

    2004-06-01

    This annual technical progress report summarizes the work accomplished during the second year of the program, January-December 2003, in the following task areas: Task 1--Conceptual Design, Task 2--Laboratory Scale Evaluations, Task 3--OTM Development, Task 4--Economic Evaluation and Commercialization Planning and Task 5--Program Management. The program has experienced significant delays due to several factors. The budget has also been significantly under spent. Based on recent technical successes and confirmation of process economics, significant future progress is expected. Concepts for integrating Oxygen Transport Membranes (OTMs) into boilers and process heaters to facilitate oxy-fuel combustion have been investigated. OTM reactor combustion testing was delayed to insufficient reliability of the earlier OTM materials. Substantial improvements to reliability have been identified and testing will recommence early in 2004. Promising OTM material compositions and OTM architectures have been identified that improve the reliability of the ceramic elements. Economic evaluation continued. Information was acquired that quantified the attractiveness of the advanced oxygen-fired boiler. CO{sub 2} capture and compression are still estimated to be much less than $10/ton CO{sub 2}.

  1. Measuring Grammatical Development in Bilingual Mandarin-English Speaking Children with a Sentence Repetition Task

    ERIC Educational Resources Information Center

    Woon, Chai Ping; Yap, Ngee Thai; Lim, Hui Woan; Wong, Bee Eng

    2014-01-01

    Sentence repetition (SR) tasks have been used to measure children's expressive language skills in normal and abnormal language development, and to examine the development of the speaking skills in second language acquisition, as well as to survey the proficiency of bilingual language development. Recently, SR tasks have been recognized as a…

  2. Development of a task-level robot programming and simulation system

    NASA Technical Reports Server (NTRS)

    Liu, H.; Kawamura, K.; Narayanan, S.; Zhang, G.; Franke, H.; Ozkan, M.; Arima, H.; Liu, H.

    1987-01-01

    An ongoing project in developing a Task-Level Robot Programming and Simulation System (TARPS) is discussed. The objective of this approach is to design a generic TARPS that can be used in a variety of applications. Many robotic applications require off-line programming, and a TARPS is very useful in such applications. Task level programming is object centered in that the user specifies tasks to be performed instead of robot paths. Graphics simulation provides greater flexibility and also avoids costly machine setup and possible damage. A TARPS has three major modules: world model, task planner and task simulator. The system architecture, design issues and some preliminary results are given.

  3. Functional Task Test (FTT)

    NASA Technical Reports Server (NTRS)

    Bloomberg, Jacob J.; Mulavara, Ajitkumar; Peters, Brian T.; Rescheke, Millard F.; Wood, Scott; Lawrence, Emily; Koffman, Igor; Ploutz-Snyder, Lori; Spiering, Barry A.; Feeback, Daniel L.; Platts, Steven H.; Stenger, Michael B.; Lee, Stuart M.C.; Arzeno, Natalia; Feiveson, Alan H.; Ryder, Jeffrey; Garcia, Yamil; Guilliams, Mark E.

    2009-01-01

    This slide presentation reviews the Functional Task Test (FTT), an interdisciplinary testing regimen that has been developed to evaluate astronaut postflight functional performance and related physiological changes. The objectives of the project are: (1) to develop a set of functional tasks that represent critical mission tasks for the Constellation Program, (2) determine the ability to perform these tasks after space flight, (3) Identify the key physiological factors that contribute to functional decrements and (4) Use this information to develop targeted countermeasures.

  4. Screening of processing and upgrading schemes. Task 3

    SciTech Connect

    Not Available

    1991-10-01

    The RFP was predicated on DOE`s desire to enhance the development of advanced transportation fuels made from coal via a program to process mild coal gasification (MCG) liquids into high volumetric energy density (HEDF) test fuels. The desired product fuels were to be cost effectively manufactured, have high volumetric energy density, and be hydrocarbon-based for existing and prototype turbine and diesel engines. The sources for these special fuels consist of the abundant and secure indigenous energy resources of coal. Comparison studies were also to be made using other non-petroleum fossil fuels such as shale oil and tar sands bitumen. METC has concluded that MCG technology has the potential to simultaneously satisfy the transportation and power generation fuel needs in the most cost-effective manner. MCG is based on low temperature pyrolysis, a technique known to the coal community for over a century. Most past pyrolysis developments were aimed at maximizing the liquids yield which results in a low quality tarry product requiring significant and capital intensive upgrading. By properly tailoring the pyrolysis severity to control the liquid yield-liquid quality relationship, it has been found that a higher quality distillate-boiling liquid can be readily ``skimmed`` from the coal. The resultant liquids have a much higher H/C ratio than conventional pyrolytic tars and therefore can be hydroprocessed at lower cost. These liquids are also extremely enriched in 1-, 2-, and 3-ring aromatics.

  5. An analysis of the application of AI to the development of intelligent aids for flight crew tasks

    NASA Technical Reports Server (NTRS)

    Baron, S.; Feehrer, C.

    1985-01-01

    This report presents the results of a study aimed at developing a basis for applying artificial intelligence to the flight deck environment of commercial transport aircraft. In particular, the study was comprised of four tasks: (1) analysis of flight crew tasks, (2) survey of the state-of-the-art of relevant artificial intelligence areas, (3) identification of human factors issues relevant to intelligent cockpit aids, and (4) identification of artificial intelligence areas requiring further research.

  6. Performance management in healthcare: performance indicator development, task uncertainty, and types of performance indicators.

    PubMed

    van der Geer, Eric; van Tuijl, Harrie F J M; Rutte, Christel G

    2009-11-01

    In healthcare, performance indicators are increasingly used to measure and control quality and efficiency of care-providing teams. This article demonstrates that when controllability is emphasized during indicator development, the level of task uncertainty influences the type of resulting performance indicators. We report findings from a field study in a medical rehabilitation centre in The Netherlands, where four low task uncertain teams ('hand trauma', 'heart failure', 'amputation', 'chronic pain'), and four high task uncertain teams ('children with developmental coordination disorders (DCD)', 'parkinson's disease', 'young children (0-4 years) with developmental disorders', and 'acquired brain injuries') participated in the development of performance indicators using the Productivity Measurement and Enhancement System (ProMES) method. Results show that teams higher on task uncertainty developed relatively more process indicators compared to outcome indicators, whereas the reverse was true for teams lower on task uncertainty. Additionally, process indicators developed by high task uncertain teams were more of a problem solving nature than process indicators developed by low task uncertain teams, which had a more procedural character. The study expands existing knowledge by providing a framework which explicates the task processes to be executed under different levels of task uncertainty, and in line with that appropriate performance indicators for healthcare teams.

  7. Student Perceptions of Social Task Development in Online Group Project Work

    ERIC Educational Resources Information Center

    Morgan, Kari; Cameron, Bruce A.; Williams, Karen C.

    2009-01-01

    This article explores student perceptions of social task development in an online group project and poses recommendations for implementation of group projects. Qualitative methods were used to analyze student perceptions of social task development in online group project. Respect, "being nice," follow the rules/follow the leader, communication,…

  8. Effective Behavior Management in Preschool Classrooms and Children's Task Orientation: Enhancing Emergent Literacy and Language Development

    ERIC Educational Resources Information Center

    Dobbs-Oates, Jennifer; Kaderavek, Joan N.; Guo, Ying; Justice, Laura M.

    2011-01-01

    This study investigated the relations among preschool teachers' behavior management, children's task orientation, and children's emergent literacy and language development, as well as the extent to which task orientation moderated the relation between teachers' behavior management and children's emergent literacy and language development.…

  9. Professional Identity Development: A Grounded Theory of Transformational Tasks of New Counselors

    ERIC Educational Resources Information Center

    Gibson, Donna M.; Dollarhide, Colette T.; Moss, Julie M.

    2010-01-01

    Professional identity development is an important professional issue. Examining the lived experiences of counselors-in-training (CITs), the authors used grounded theory methodology to describe the transformational tasks that are required for professional identity development. Tasks include finding a personal definition of counseling, internalizing…

  10. "ZERO TO THREE's" Task Force on Culture and Development: Learning to Walk the Talk

    ERIC Educational Resources Information Center

    Mann, Tammy; Steward, Marva; Eggbeer, Linda; Norton, Dolores

    2007-01-01

    The Executive Committee at "ZERO TO THREE" created a Task Force on Culture and Development to deepen our understanding of the role of culture in child development and to guide the organization through a self-assessment process to better understand how staff and board members address the issue of culture in their work. The task force's literature…

  11. Hospital Pharmacy Technician Project; Development and Validation of the Task Inventory. Interim Report.

    ERIC Educational Resources Information Center

    Henrich, Robert R.; Goldsmith, Katherine L.

    Evaluations of existing pharmacy personnel programs and personal interviews with leaders in the field were conducted to develop a pharmacist and technician task list. Using the survey instrument developed for other occupations, the National Technical Advisory Committee for Pharmacy analyzed and validated the task list. The final organization of…

  12. Task 3.13 - Hot-Gas Filter Testing

    SciTech Connect

    Michael L. Swanson

    1998-01-01

    The objectives of the hot-gas cleanup (HGC) work on the transport reactor demonstration unit (TRDU) located at the Energy and Environmental Research Center (EERC) is to demonstrate acceptable performance of hot-gas filter elements in a pilot-scale system prior to long-term demonstration tests. The primary focus of the experimental effort in the 3-year project is the testing of hot-gas filter element performance (particulate collection efficiency, filter pressure differential, filter cleanability, and durability) as a fiction of temperature and filter face velocity during short-term operation (100-200 hours). The filter vessel is used in combination with the TRDU to evaluate the performance of selected hot-gas filter elements under gasification operating conditions. This work directly supports the power systems development facility (PSDF) utilizing the M.W. Kellogg transport reactor located at Wilsonville, Alabama (1) and, indirectly, the Foster Wheeler advanced pressurized fluid-bed combustor, also located at Wilsonville (2).

  13. 3 CFR 13540 - Executive Order 13540 of April 26, 2010. Interagency Task Force on Veterans Small Business...

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Task Force on Veterans Small Business Development 13540 Order 13540 Presidential Documents Executive... interagency task force to coordinate the efforts of Federal agencies to improve capital, business development... Administration an Interagency Task Force on Veterans Small Business Development (Task Force). Sec. 2....

  14. Task-evoked pupillometry provides a window into the development of short-term memory capacity

    PubMed Central

    Johnson, Elizabeth L.; Miller Singley, Alison T.; Peckham, Andrew D.; Johnson, Sheri L.; Bunge, Silvia A.

    2014-01-01

    The capacity to keep multiple items in short-term memory (STM) improves over childhood and provides the foundation for the development of multiple cognitive abilities. The goal of this study was to measure the extent to which age differences in STM capacity are related to differences in task engagement during encoding. Children (n = 69, mean age = 10.6 years) and adults (n = 54, mean age = 27.5 years) performed two STM tasks: the forward digit span test from the Wechsler Intelligence Scale for Children (WISC) and a novel eyetracking digit span task designed to overload STM capacity. Building on prior research showing that task-evoked pupil dilation can be used as a real-time index of task engagement, we measured changes in pupil dilation while participants encoded long sequences of digits for subsequent recall. As expected, adults outperformed children on both STM tasks. We found similar patterns of pupil dilation while children and adults listened to the first six digits on our STM overload task, after which the adults' pupils continued to dilate and the children's began to constrict, suggesting that the children had reached their cognitive limits and that they had begun to disengage from the task. Indeed, the point at which pupil dilation peaked at encoding was a significant predictor of WISC forward span, and this relationship held even after partialing out recall performance on the STM overload task. These findings indicate that sustained task engagement at encoding is an important component of the development of STM. PMID:24659980

  15. Task-evoked pupillometry provides a window into the development of short-term memory capacity.

    PubMed

    Johnson, Elizabeth L; Miller Singley, Alison T; Peckham, Andrew D; Johnson, Sheri L; Bunge, Silvia A

    2014-01-01

    The capacity to keep multiple items in short-term memory (STM) improves over childhood and provides the foundation for the development of multiple cognitive abilities. The goal of this study was to measure the extent to which age differences in STM capacity are related to differences in task engagement during encoding. Children (n = 69, mean age = 10.6 years) and adults (n = 54, mean age = 27.5 years) performed two STM tasks: the forward digit span test from the Wechsler Intelligence Scale for Children (WISC) and a novel eyetracking digit span task designed to overload STM capacity. Building on prior research showing that task-evoked pupil dilation can be used as a real-time index of task engagement, we measured changes in pupil dilation while participants encoded long sequences of digits for subsequent recall. As expected, adults outperformed children on both STM tasks. We found similar patterns of pupil dilation while children and adults listened to the first six digits on our STM overload task, after which the adults' pupils continued to dilate and the children's began to constrict, suggesting that the children had reached their cognitive limits and that they had begun to disengage from the task. Indeed, the point at which pupil dilation peaked at encoding was a significant predictor of WISC forward span, and this relationship held even after partialing out recall performance on the STM overload task. These findings indicate that sustained task engagement at encoding is an important component of the development of STM.

  16. Task 8.4 - High Temperature Turbine Disk Development

    SciTech Connect

    1997-02-27

    The goal of this task is to demonstrate a bonding technique to produce a dual-alloy turbine disk concept which will satisfy the diverse property requirements of the rim and hub areas of the disk. The program examines methods of attaching a cast superalloy rim with sufficient rupture strength to a fine grain hub materials with the required LCF properties. The goals of the program were established in the context of a preliminary turbine design by Solar Turbines, Inc. designated ATS 5. The initial target for the ATS 5 application was to allow rim operating temperatures in the 1350-1400 {degrees} F range. The life goal of the Dual-Alloy Disk was envisioned to maintain Solar`s standard turbine disk philosophy of 1000,000 hours.

  17. AIDS: developing a primary health care task force.

    PubMed

    Graham, L; Cates, J A

    1987-12-01

    As the number of people with AIDS increases, the number of people impacted by the AIDS crisis will also increase. Larger metropolitan areas have already responded to the crisis with various services (Deuchar, 1984); but the disease has yet to fully impact on smaller cities and towns. The formation of community service groups to cope with the AIDS crisis is a virtual necessity in health care preparation for persons with AIDS. The experience of the Fort Wayne AIDS Task Force reflects the potential of any community to utilize the existing resources in the gay and lesbian community, health and social service professions, and among family and friends of persons with AIDS. Consultation and resources are available through local and state boards of health, as well as local social service and health personnel currently dealing with the AIDS crisis. PMID:3430436

  18. National facilities study. Volume 5: Space research and development facilities task group

    NASA Technical Reports Server (NTRS)

    1994-01-01

    With the beginnings of the U.S. space program, there was a pressing need to develop facilities that could support the technology research and development, testing, and operations of evolving space systems. Redundancy in facilities that was once and advantage in providing flexibility and schedule accommodation is instead fast becoming a burden on scarce resources. As a result, there is a clear perception in many sectors that the U.S. has many space R&D facilities that are under-utilized and which are no longer cost-effective to maintain. At the same time, it is clear that the U.S. continues to possess many space R&D facilities which are the best -- or among the best -- in the world. In order to remain world class in key areas, careful assessment of current capabilities and planning for new facilities is needed. The National Facility Study (NFS) was initiated in 1992 to develop a comprehensive and integrated long-term plan for future aerospace facilities that meets current and projected government and commercial needs. In order to assess the nation's capability to support space research and development (R&D), a Space R&D Task Group was formed. The Task Group was co-chaired by NASA and DOD. The Task Group formed four major, technologically- and functionally- oriented working groups: Human and Machine Operations; Information and Communications; Propulsion and Power; and Materials, Structures, and Flight Dynamics. In addition to these groups, three supporting working groups were formed: Systems Engineering and Requirements; Strategy and Policy; and Costing Analysis. The Space R&D Task Group examined several hundred facilities against the template of a baseline mission and requirements model (developed in common with the Space Operations Task Group) and a set of excursions from the baseline. The model and excursions are described in Volume 3 of the NFS final report. In addition, as a part of the effort, the group examined key strategic issues associated with space R

  19. The Development of the C3 Framework

    ERIC Educational Resources Information Center

    Social Education, 2013

    2013-01-01

    Susan Griffin, executive director of NCSS, was chair of the Task Force of Professional Organizations that initiated and guided the development of "The College, Career, and Civic Life (C3) Framework for Social Studies State Standards", which will soon be released. In this interview with "Social Education", Susan explains how the…

  20. GRASP/Ada: Graphical Representations of Algorithms, Structures, and Processes for Ada. The development of a program analysis environment for Ada: Reverse engineering tools for Ada, task 2, phase 3

    NASA Technical Reports Server (NTRS)

    Cross, James H., II

    1991-01-01

    The main objective is the investigation, formulation, and generation of graphical representations of algorithms, structures, and processes for Ada (GRASP/Ada). The presented task, in which various graphical representations that can be extracted or generated from source code are described and categorized, is focused on reverse engineering. The following subject areas are covered: the system model; control structure diagram generator; object oriented design diagram generator; user interface; and the GRASP library.

  1. Lunar surface construction and assembly equipment study: Lunar Base Systems Study (LBSS) task 5.3

    NASA Technical Reports Server (NTRS)

    1988-01-01

    A set of construction and assembly tasks required on the lunar surface was developed, different concepts for equipment applicable to the tasks determined, and leading candidate systems identified for future conceptual design. Data on surface construction and assembly equipment systems are necessary to facilitate an integrated review of a complete lunar scenario.

  2. Implementing the Science Assessment Standards: Developing and validating a set of laboratory assessment tasks in high school biology

    NASA Astrophysics Data System (ADS)

    Saha, Gouranga Chandra

    Very often a number of factors, especially time, space and money, deter many science educators from using inquiry-based, hands-on, laboratory practical tasks as alternative assessment instruments in science. A shortage of valid inquiry-based laboratory tasks for high school biology has been cited. Driven by this need, this study addressed the following three research questions: (1) How can laboratory-based performance tasks be designed and developed that are doable by students for whom they are designed/written? (2) Do student responses to the laboratory-based performance tasks validly represent at least some of the intended process skills that new biology learning goals want students to acquire? (3) Are the laboratory-based performance tasks psychometrically consistent as individual tasks and as a set? To answer these questions, three tasks were used from the six biology tasks initially designed and developed by an iterative process of trial testing. Analyses of data from 224 students showed that performance-based laboratory tasks that are doable by all students require careful and iterative process of development. Although the students demonstrated more skill in performing than planning and reasoning, their performances at the item level were very poor for some items. Possible reasons for the poor performances have been discussed and suggestions on how to remediate the deficiencies have been made. Empirical evidences for validity and reliability of the instrument have been presented both from the classical and the modern validity criteria point of view. Limitations of the study have been identified. Finally implications of the study and directions for further research have been discussed.

  3. Chemometrics review for chemical sensor development, task 7 report

    SciTech Connect

    1994-05-01

    This report, the seventh in a series on the evaluation of several chemical sensors for use in the U.S. Department of Energy`s (DOE`s) site characterization and monitoring programs, concentrates on the potential use of chemometrics techniques in analysis of sensor data. Chemometrics is the chemical discipline that uses mathematical, statistical, and other methods that employ formal logic to: design or select optimal measurement procedures and experiments and provide maximum relevant chemical information by analyzing chemical data. The report emphasizes the latter aspect. In a formal sense, two distinct phases are in chemometrics applications to analytical chemistry problems: (1) the exploratory data analysis phase and (2) the calibration and prediction phase. For use in real-world problems, it is wise to add a third aspect - the independent validation and verification phase. In practical applications, such as the ERWM work, and in order of decreasing difficulties, the most difficult tasks in chemometrics are: establishing the necessary infrastructure (to manage sampling records, data handling, and data storage and related aspects), exploring data analysis, and solving calibration problems, especially for nonlinear models. Chemometrics techniques are different for what are called zeroth-, first-, and second-order systems, and the details depend on the form of the assumed functional relationship between the measured response and the concentrations of components in mixtures. In general, linear relationships can be handled relatively easily, but nonlinear relationships can be difficult.

  4. Conceptualizing the Work of Leading Mathematical Tasks in Professional Development

    ERIC Educational Resources Information Center

    Elliott, Rebekah; Kazemi, Elham; Lesseig, Kristin; Mumme, Judith; Carroll, Cathy; Kelley-Petersen, Megan

    2009-01-01

    Filling the knowledge gap in the limited research on professional development leaders is an urgent issue if teacher learning is to be improved. This research and development project is studying how leaders learn to cultivate mathematically rich professional development environments. The authors adapted two frameworks from classroom-based…

  5. Identity Development in German Emerging Adults: Not an Easy Task

    ERIC Educational Resources Information Center

    Seiffge-Krenke, Inge; Haid, Marja-Lena

    2012-01-01

    In this chapter, we review identity development in German youth as well as the impact of German cultural history on difficulties in developing a sense of national identity. Current socioeconomic and political contexts, such as instability of labor markets and prolonged transitions to work and partnership, are likely to affect identity development.…

  6. Environmental management technology demonstration and commercialization: Tasks 2, 3, 4, and 8. Semiannual report, October 1994--March 1995

    SciTech Connect

    Hawthorne, S.B.; Ness, R.O. Jr.; Nowok, J.W.; Pflughoeft-Hassett, D.; Hurley, J.P.; Steadman, E.N.

    1995-05-01

    The objective of the Environmental Management program at the Energy and Environmental Research Center (EERC) is to develop, demonstrate, and commercialize technologies that address the environmental management needs of contaminated sites, including characterization, sensors, and monitoring; low-level mixed waste processing; material disposition technology; improved waste forms; in situ containment and remediation; and efficient separation technologies for radioactive wastes. Task 2 is the extraction and analysis of pollutant organics from contaminated solids using off-line supercritical fluid extraction (SFE) and on-line SFE-infrared spectroscopy. Task 3, pyrolysis of plastics, has as its objectives to develop a commercial process to significantly reduce the volume of mixed-plastics-paper-resin waste contaminated with low-level radioactive material; concentrate contaminants in a collectible form; and determine the distribution and form of contaminants after pyrolysis of the mixed waste. Task 4, stabilization of vitrified wastes, has as its objectives to (1) demonstrate a waste vitrification procedure for enhanced stabilization of waste materials and (2) develop a testing protocol to understand the long-term leaching behavior of the stabilized waste form. The primary objective of Task 8, Management and reporting, is coordination of this project with other programs and opportunities. In addition, management oversight will be maintained to ensure that tasks are completed and coordinated as planned and that deliverables are submitted in a timely manner. Accomplishments to date is each task are described. 62 refs.

  7. Development of Job Task Inventories and Their Use in Job Analysis Research.

    ERIC Educational Resources Information Center

    Gael, Sidney

    An approach to developing job task inventory questionnaires by interviewing supervisors or job incumbents is described. An initial interview provides the bulk of the information from which task statements will be extracted. A verification interview is conducted with a different interviewee to check and modify information obtained in the initial…

  8. The Administrative Tasks and Professional Development Needs of Heads of Academic Departments.

    ERIC Educational Resources Information Center

    Lonsdale, Alan J.; Bardsley, W. Neil

    The range of administrative tasks performed by 679 heads of academic departments in Australian colleges of advanced education was surveyed, along with the perceptions of the administrators of their professional development needs. In addition to information about the respondent's appointment and experience, a questionnaire addressed 83 tasks,…

  9. Development and Validation of an Admission Test Designed to Assess Samples of Performance on Academic Tasks

    ERIC Educational Resources Information Center

    Tanilon, Jenny; Segers, Mien; Vedder, Paul; Tillema, Harm

    2009-01-01

    This study illustrates the development and validation of an admission test, labeled as Performance Samples on Academic Tasks in Educational Sciences (PSAT-Ed), designed to assess samples of performance on academic tasks characteristic of those that would eventually be encountered by examinees in an Educational Sciences program. The test was based…

  10. [Ocra Method: development of a new procedure for analysis of multiple tasks subject to infrequent rotation].

    PubMed

    Occhipinti, E; Colombini, Daniela; Occhipinti, M

    2008-01-01

    In the Ocra methods (Ocra index and Ocra Checklist), when computing the final indices (Ocra index or checklist score), in the case of more than one repetitive task a "traditional" procedure was already proposed, the results of which could be defined as "time-weighted average". This approach appears to be appropriate when considering rotations among tasks that are performed very frequently, for instance almost once every hour (or for shorter periods). However, when rotation among repetitive tasks is less frequent (i.e. once every 1 1/2 or more hours), the "time-weighted average" approach could result in an underestimation of the exposure level (as it practically flattens peaks of high exposures). For those scenarios an alternative approach based on the "most stressful task as minimum" might be more realistic. This latter approach has already been included in the NIOSH approach for multiple sequential lifting tasks and, given the recent availability in the Ocra method of more detailed duration multipliers (practically one different Du(M) for each different step of one hour of duration of the repetitive task), it is now possible to define a particular procedure to compute the complex Ocra Multitask Index (cOCRA) and the complex Checklist Score (cCHESCO) for the analysis of two or more repetitive tasks when rotations are infrequent (rotations every 1 1/2 hours or more). The result of this approach will be at least equal to the index of the most stressful task considered for its individual daily duration and at the most equal to the index of the most stressful task when it is (only theoretically) considered as lasting for the overall daily duration of all examined repetitive tasks. The procedure is based on the following formula: Complex Ocra Multitask Index = Ocra(1(Dum1) + (Delta ocra1xK) where 1,2,3,...,N = repetitive tasks ordered by ocra index values (1 = highest; N = lowest) computed considering respective real duration multipliers (Dum(i)). ocra1 = ocra index of

  11. The Dynamics of Development on the Dimensional Change Card Sorting Task

    ERIC Educational Resources Information Center

    van Bers, Bianca M. C. W.; Visser, Ingmar; van Schijndel, Tessa J. P.; Mandell, Dorothy J.; Raijmakers, Maartje E. J.

    2011-01-01

    A widely used paradigm to study cognitive flexibility in preschoolers is the Dimensional Change Card Sorting (DCCS) task. The developmental dynamics of DCCS performance was studied in a cross-sectional design (N = 93, 3 to 5 years of age) using a computerized version of the standard DCCS task. A model-based analysis of the data showed that…

  12. Afrocentricity: The Missing Task in Black Adult Development?

    ERIC Educational Resources Information Center

    Littleton, Roosevelt, Jr.

    Student development theories and student-support programs should be designed to meet the special needs of culturally diverse populations. Specifically, those responsible for teaching and helping black students must create models of human and student development that take into account the unique needs and experiences that black students bring to…

  13. Solar dynamic heat rejection technology. Task 1: System concept development

    NASA Technical Reports Server (NTRS)

    Gustafson, Eric; Carlson, Albert W.

    1987-01-01

    The results are presented of a concept development study of heat rejection systems for Space Station solar dynamic power systems. The heat rejection concepts are based on recent developments in high thermal transport capacity heat pipe radiators. The thermal performance and weights of each of the heat rejection subsystems is addressed in detail, and critical technologies which require development tests and evaluation for successful demonstration are assessed and identified. Baseline and several alternate heat rejection system configurations and optimum designs are developed for both Brayton and Rankine cycles. The thermal performance, mass properties, assembly requirements, reliability, maintenance requirements and life cycle cost are determined for each configuration. A specific design was then selected for each configuration which represents an optimum design for that configuration. The final recommendations of heat rejection system configuration for either the Brayton or Rankine cycles depend on the priorities established for the evaluation criteria.

  14. Large-area sheet task advanced dendritic web growth development

    NASA Technical Reports Server (NTRS)

    Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.; Meier, D.; Schruben, J.

    1982-01-01

    The "discrete shield' temperature model was completed and verified. Modifications to the J419 low stress configuration were tested experimentally to evaluate effects on growth speed. A composite lid and shield configuration combining the low stress features of the J419 with the width limiting characteristics of the J98M3 was fabricated and tested in the N-furnace. Several long crystals were grown with width limited to about 3.3 cm and with melt replenishment, although the configuration is not yet optimized for steady state growth.

  15. Designing Spatial Visualisation Tasks for Middle School Students with a 3D Modelling Software: An Instrumental Approach

    ERIC Educational Resources Information Center

    Turgut, Melih; Uygan, Candas

    2015-01-01

    In this work, certain task designs to enhance middle school students' spatial visualisation ability, in the context of an instrumental approach, have been developed. 3D modelling software, SketchUp®, was used. In the design process, software tools were focused on and, thereafter, the aim was to interpret the instrumental genesis and spatial…

  16. The Health Services Mobility Study Method of Task Analysis and Curriculum Design. Research Report No. 11. Volume 4: Developing Curriculum Objectives from Task Data: A Manual.

    ERIC Educational Resources Information Center

    Gilpatrick, Eleanor; Gullion, Christina

    This document is volume 4 of a four-volume report which describes the components of the Health Services Mobility Study (HSMS) method of task analysis, job ladder design, and curriculum development. Divided into three chapters, volume 4 is a manual for using HSMS task data and analysis results to develop curriculum objectives, guidelines, and…

  17. Advanced diesel engine component development program, tasks 4-14

    NASA Astrophysics Data System (ADS)

    Kaushal, Tony S.; Weber, Karen E.

    1994-11-01

    This report summarizes the Advanced Diesel Engine Component Development (ADECD) Program to develop and demonstrate critical technology needed to advance the heavy-duty low heat rejection engine concept. Major development activities reported are the design, analysis, and fabrication of monolithic ceramic components; vapor phase and solid film lubrication; electrohydraulic valve actuation; and high pressure common rail injection. An advanced single cylinder test bed was fabricated as a laboratory tool in studying these advanced technologies. This test bed simulates the reciprocator for a system having no cooling system, turbo compounding, Rankine bottoming cycle, common rail injection, and variable valve actuation to achieve fuel consumption of 160 g/kW-hr (.26 lb/hp-hr). The advanced concepts were successfully integrated into the test engine. All ceramic components met their functional and reliability requirements. The firedeck, cast-in-place ports, valves, valve guides, piston cap, and piston ring were made from silicon nitride. Breakthroughs required to implement a 'ceramic' engine included the fabrication of air-gap cylinder heads, elimination of compression gaskets, machining of ceramic valve seats within the ceramic firedeck, fabrication of cast-in-place ceramic port liners, implementation of vapor phase lubrication, and elimination of the engine coolant system. Silicon nitride valves were successfully developed to meet several production abuse test requirements and incorporated into the test bed with a ceramic valve guide and solid film lubrication. The ADECD cylinder head features ceramic port shields to increase insulation and exhaust energy recovery. The combustion chamber includes a ceramic firedeck and piston cap. The tribological challenge posed by top ring reversal temperatures of 550 C was met through the development of vapor phase lubrication using tricresyl phosphate at the ring-liner interface. A solenoid-controlled, variable valve actuation system

  18. Advanced diesel engine component development program, tasks 4-14

    NASA Technical Reports Server (NTRS)

    Kaushal, Tony S.; Weber, Karen E.

    1994-01-01

    This report summarizes the Advanced Diesel Engine Component Development (ADECD) Program to develop and demonstrate critical technology needed to advance the heavy-duty low heat rejection engine concept. Major development activities reported are the design, analysis, and fabrication of monolithic ceramic components; vapor phase and solid film lubrication; electrohydraulic valve actuation; and high pressure common rail injection. An advanced single cylinder test bed was fabricated as a laboratory tool in studying these advanced technologies. This test bed simulates the reciprocator for a system having no cooling system, turbo compounding, Rankine bottoming cycle, common rail injection, and variable valve actuation to achieve fuel consumption of 160 g/kW-hr (.26 lb/hp-hr). The advanced concepts were successfully integrated into the test engine. All ceramic components met their functional and reliability requirements. The firedeck, cast-in-place ports, valves, valve guides, piston cap, and piston ring were made from silicon nitride. Breakthroughs required to implement a 'ceramic' engine included the fabrication of air-gap cylinder heads, elimination of compression gaskets, machining of ceramic valve seats within the ceramic firedeck, fabrication of cast-in-place ceramic port liners, implementation of vapor phase lubrication, and elimination of the engine coolant system. Silicon nitride valves were successfully developed to meet several production abuse test requirements and incorporated into the test bed with a ceramic valve guide and solid film lubrication. The ADECD cylinder head features ceramic port shields to increase insulation and exhaust energy recovery. The combustion chamber includes a ceramic firedeck and piston cap. The tribological challenge posed by top ring reversal temperatures of 550 C was met through the development of vapor phase lubrication using tricresyl phosphate at the ring-liner interface. A solenoid-controlled, variable valve actuation system

  19. Biomedical engineering tasks. [electrode development for electrocardiography and electroencephalography

    NASA Technical Reports Server (NTRS)

    1972-01-01

    Electrocardiographic and vectorcardiographic bioinstrumentation work centered on the development of a new electrode system harness for Project Skylab. Evaluation of several silver electrode configurations proved superior impedance voltage performance for silver/silver chloride electrodes mounted flush by using a paste adhesive. A portable ECG processor has been designed and a breadboard unit has been built to sample ECG input data at a rate of 500 samples per second for arrhythmia detection. A small real time display driver program has been developed for statistical analysis on selected QPS features. Engineering work on a sleep monitoring cap assembly continued.

  20. Internal R and D task summary report: analytical methods development

    SciTech Connect

    Schweighardt, F.K.

    1983-07-01

    International Coal Refining Company (ICRC) conducted two research programs to develop analytical procedures for characterizing the feed, intermediates,and products of the proposed SRC-I Demonstration Plant. The major conclusion is that standard analytical methods must be defined and assigned statistical error limits of precision and reproducibility early in development. Comparing all SRC-I data or data from different processes is complex and expensive if common data correlation procedures are not followed. ICRC recommends that processes be audited analytically and statistical analyses generated as quickly as possible, in order to quantify process-dependent and -independent variables. 16 references, 10 figures, 20 tables.

  1. Defining Administrative Tasks, Evaluating Performance, and Developing Skills.

    ERIC Educational Resources Information Center

    Herman, Janice L.; Herman, Jerry J.

    1995-01-01

    To ensure high performance, administrators should develop an articulated structure and process systems approach that identifies the critical success factors (CSFs) of performance for each position; appropriate indicators and scales; and a personal-improvement plan based on last year's evaluation. Once CSFs are identified and written into the…

  2. Large-area sheet task advanced dendritic web growth development

    NASA Technical Reports Server (NTRS)

    Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.

    1983-01-01

    Modeling in the development of low stress configurations for wide web growth is presented. Parametric sensitivity to identify design features which can be used for dynamic trimming of the furnace element was studied. Temperature measurements of experimental growth behavior led to modification in the growth system to improve lateral temperature distributions.

  3. Space station data system analysis/architecture study. Task 3: Trade studies, DR-5, volume 1

    NASA Technical Reports Server (NTRS)

    1985-01-01

    The primary objective of Task 3 is to provide additional analysis and insight necessary to support key design/programmatic decision for options quantification and selection for system definition. This includes: (1) the identification of key trade study topics; (2) the definition of a trade study procedure for each topic (issues to be resolved, key inputs, criteria/weighting, methodology); (3) conduct tradeoff and sensitivity analysis; and (4) the review/verification of results within the context of evolving system design and definition. The trade study topics addressed in this volume include space autonomy and function automation, software transportability, system network topology, communications standardization, onboard local area networking, distributed operating system, software configuration management, and the software development environment facility.

  4. Parametric study of potential early commercial power plants Task 3-A MHD cost analysis

    NASA Technical Reports Server (NTRS)

    1983-01-01

    The development of costs for an MHD Power Plant and the comparison of these costs to a conventional coal fired power plant are reported. The program is divided into three activities: (1) code of accounts review; (2) MHD pulverized coal power plant cost comparison; (3) operating and maintenance cost estimates. The scope of each NASA code of account item was defined to assure that the recently completed Task 3 capital cost estimates are consistent with the code of account scope. Improvement confidence in MHD plant capital cost estimates by identifying comparability with conventional pulverized coal fired (PCF) power plant systems is undertaken. The basis for estimating the MHD plant operating and maintenance costs of electricity is verified.

  5. Biowaste resistojet propellant system biological and functional analysis, task 3

    NASA Technical Reports Server (NTRS)

    1972-01-01

    Exhaust flow contamination aspects of the biowaste resistojet are studied by evaluating effects of operating pressure, temperature and composition. Biowaste propellant mixtures considered are comprised of: (1) The Sabatier reactor effluent; (2) the effluent of the cabin carbon dioxide molecular sieve; and (3) water and water vapor from various sources. Results show that plume shapes of resistojet thrusters in the 25 to 100 mlb range exhibit greater apex angles for a given density contour than a scaled inviscid jet. Operation at low thrust, low pressure and high temperature accentuates this pluming due to viscous effects in the nozzle flow. Since the biowaste resistojet effluent is traveling at high velocity in the plume away from the aircraft it is found to be a superior method of damping than the ambient venting.

  6. The Development of Sensitivity to Sublexical Orthographic Constraints: An Investigation of Positional Frequency and Consistency Using a Wordlikeness Choice Task

    ERIC Educational Resources Information Center

    O'Brien, Beth A.

    2014-01-01

    The developmental sequence of the types of orthographic knowledge that children acquire early in reading development is unclear. Following findings of skilled reading, the orthographic constraints of positional frequency and feedback consistency were explored with a wordlikeness judgement task for grades 1-3 English-speaking children. The data…

  7. Exploration Requirements Development Utilizing the Strategy-to-Task-to-Technology Development Approach

    NASA Technical Reports Server (NTRS)

    Drake, Bret G.; Josten, B. Kent; Monell, Donald W.

    2004-01-01

    The Vision for Space Exploration provides direction for the National Aeronautics and Space Administration to embark on a robust space exploration program that will advance the Nation s scientific, security, and economic interests. This plan calls for a progressive expansion of human capabilities beyond low earth orbit seeking to answer profound scientific and philosophical questions while responding to discoveries along the way. In addition, the Vision articulates the strategy for developing the revolutionary new technologies and capabilities required for the future exploration of the solar system. The National Aeronautics and Space Administration faces new challenges in successfully implementing the Vision. In order to implement a sustained and affordable exploration endeavor it is vital for NASA to do business differently. This paper provides an overview of the strategy-to-task-to-technology process being used by NASA s Exploration Systems Mission Directorate to develop the requirements and system acquisition details necessary for implementing a sustainable exploration vision.

  8. Alfalfa variety development. Minnesota Agripower Project, Task II research report

    SciTech Connect

    Lamb, J.F.S.; Samac, D.A.; Sheaffer, C.C.

    1997-10-30

    This report briefly summarizes preliminary results from crossbreeding alfalfa to develop desirable characteristics for a dedicated biomass feed stock. The varieties development is part of a larger project which includes preparation and gasification of the alfalfa stems for energy production, and use of the co-product alfalfa leaves in livestock feed. The desired alfalfa traits include winter hardiness, resistance to major pathogens, resistance to foliar disease complexes, many thick, tall, solid, non-lodging stems with high lignin content, delayed flowering, and high quality leaves retained through harvest. Currently no alfalfa varieties meet these criteria. Three crosses were made using old European varieties, with thick stems, and modern resistant varieties. The crossbreeds showed some resistance to diseases, but increased resistance is needed to maximize leaf and steam yield. 1 tab.

  9. Large area sheet task: Advanced dendritic web growth development

    NASA Technical Reports Server (NTRS)

    Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.; Meier, D.; Schruben, J.

    1981-01-01

    The growth of silicon dendritic web for photovoltaic applications was investigated. The application of a thermal model for calculating buckling stresses as a function of temperature profile in the web is discussed. Lid and shield concepts were evaluated to provide the data base for enhancing growth velocity. An experimental web growth machine which embodies in one unit the mechanical and electronic features developed in previous work was developed. In addition, evaluation of a melt level control system was begun, along with preliminary tests of an elongated crucible design. The economic analysis was also updated to incorporate some minor cost changes. The initial applications of the thermal model to a specific configuration gave results consistent with experimental observation in terms of the initiation of buckling vs. width for a given crystal thickness.

  10. Large-area sheet task advanced dendritic web growth development

    NASA Technical Reports Server (NTRS)

    Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.; Meier, D. L.; Schruben, J.

    1982-01-01

    Thermal models were developed that accurately predict the thermally generated stresses in the web crystal which, if too high, cause the crystal to degenerate. The application of the modeling results to the design of low-stress experimental growth configurations will allow the growth of wider web crystals at higher growth velocities. A new experimental web growth machine was constructed. This facility includes all the features necessary for carrying out growth experiments under steady thermal conditions. Programmed growth initiation was developed to give reproducible crystal starts. Width control permits the growth of long ribbons at constant width. Melt level is controlled to 0.1 mm or better. Thus, the capability exists to grow long web crystals of constant width and thickness with little operator intervention, and web growth experiments can now be performed with growth variables controlled to a degree not previously possible.

  11. Paraho oil shale module. Site development plan, Task 4

    SciTech Connect

    Not Available

    1981-10-01

    A management plan and schedule which covers all requirements for gaining access to the site and for conducting a Paraho Process demonstration program have been prepared. The oil shale available should represent a regional resource of suitable size and quality for commercial development. Discussed in this report are: proof of ownership; requirements for rights-of-way for access to the site; local zoning restrictions; water rights; site availability verification; and other legal requirements. (DMC)

  12. The end-state comfort effect in 3- to 8-year-old children in two object manipulation tasks.

    PubMed

    Knudsen, Birgit; Henning, Anne; Wunsch, Kathrin; Weigelt, Matthias; Aschersleben, Gisa

    2012-01-01

    The aim of the study was to compare 3- to 8-year-old children's propensity to anticipate a comfortable hand posture at the end of a grasping movement (end-state comfort effect) between two different object manipulation tasks, the bar-transport task, and the overturned-glass task. In the bar-transport task, participants were asked to insert a vertically positioned bar into a small opening of a box. In the overturned-glass task, participants were asked to put an overturned-glass right-side-up on a coaster. Half of the participants experienced action effects (lights) as a consequence of their movements (AE groups), while the other half of the participants did not (No-AE groups). While there was no difference between the AE and No-AE groups, end-state comfort performance differed across age as well as between tasks. Results revealed a significant increase in end-state comfort performance in the bar-transport task from 13% in the 3-year-olds to 94% in the 8-year-olds. Interestingly, the number of children grasping the bar according to end-state comfort doubled from 3 to 4 years and from 4 to 5 years of age. In the overturned-glass task an increase in end-state comfort performance from already 63% in the 3-year-olds to 100% in the 8-year-olds was significant as well. When comparing end-state comfort performance across tasks, results showed that 3- and 4-year-old children were better at manipulating the glass as compared to manipulating the bar, most probably, because children are more familiar with manipulating glasses. Together, these results suggest that preschool years are an important period for the development of motor planning in which the familiarity with the object involved in the task plays a significant role in children's ability to plan their movements according to end-state comfort.

  13. Decontamination Technologies, Task 3, Urban Remediation and Response Project

    SciTech Connect

    Heiser,J.; Sullivan, T.

    2009-06-30

    In the aftermath of a Radiological Dispersal Device (RDD, also known as a dirty bomb) it will be necessary to remediate the site including building exteriors and interiors, equipment, pavement, vehicles, personal items etc. Remediation will remove or reduce radioactive contamination from the area using a combination of removing and disposing of many assets (including possible demolition of buildings), decontaminating and returning to service other assets, and fixing in place or leaving in place contamination that is deemed 'acceptable'. The later will require setting acceptable dose standards, which will require negotiation with all involved parties and a balance of risk and cost to benefit. To accomplish the first two, disposal or decontamination, a combination of technologies will be deployed that can be loosely classified as: Decontamination; Equipment removal and size reduction; and Demolition. This report will deal only with the decontamination technologies that will be used to return assets to service or to reduce waste disposal. It will not discuss demolition, size reduction or removal technologies or equipment (e.g., backhoe mounted rams, rock splitter, paving breakers and chipping hammers, etc.). As defined by the DOE (1994), decontamination is removal of radiological contamination from the surfaces of facilities and equipment. Expertise in this field comes primarily from the operation and decommissioning of DOE and commercial nuclear facilities as well as a small amount of ongoing research and development closely related to RDD decontamination. Information related to decontamination of fields, buildings, and public spaces resulting from the Goiania and Chernobyl incidents were also reviewed and provide some meaningful insight into decontamination at major urban areas. In order to proceed with decontamination, the item being processed needs to have an intrinsic value that exceeds the cost of the cleaning and justifies the exposure of any workers during the

  14. The classification of children's knowledge: development on the balance-scale and inclined-plane tasks.

    PubMed

    Ferretti, R P; Butterfield, E C; Cahn, A; Kerkman, D

    1985-02-01

    R.S. Siegler (1981, Monographs of the Society for Research in Child Development, 46 C2, Serial No. 189) has shown that performance on several Piagetian tasks is governed by similar rule structures. The purpose of the first study was to extend his analysis to the inclined-plane task, replicate his original observations about development on the balance-scale task, and determine the consistency in children's rule usage across tasks. We found that Siegler's (1981) binary decision representations adequately characterized development on these tasks, and there was fair correspondence of rule classifications across tasks. An alternative classification procedure, used to diagnose the rules of children who failed our original classification criteria, showed that most of these children's performance patterns were very similar to Siegler's rule patterns. In the second experiment, we improved the diagnosticity of our rule-assessment protocol in light of F. Wilkening and N. H. Anderson's (1982, Psychological Bulletin, 92, 215-237) criticisms, and observed that many Rule III children's predictions were associated with those of integration rules on both tasks. Despite these methodological improvements, many children, especially 5- to 7-year-olds, evidenced use of centration and lexicographic strategies, suggesting that these classifications are not simply an artifact of problem sampling. Some of the problems associated with the classification of children's knowledge are discussed.

  15. Large-area sheet task advanced dendritic web growth development

    NASA Technical Reports Server (NTRS)

    Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.

    1984-01-01

    The thermal models used for analyzing dendritic web growth and calculating the thermal stress were reexamined to establish the validity limits imposed by the assumptions of the models. Also, the effects of thermal conduction through the gas phase were evaluated and found to be small. New growth designs, both static and dynamic, were generated using the modeling results. Residual stress effects in dendritic web were examined. In the laboratory, new techniques for the control of temperature distributions in three dimensions were developed. A new maximum undeformed web width of 5.8 cm was achieved. A 58% increase in growth velocity of 150 micrometers thickness was achieved with dynamic hardware. The area throughput goals for transient growth of 30 and 35 sq cm/min were exceeded.

  16. Results of the Gallium-Clad Phase 3 and Phase 4 tasks (canceled prior to completion)

    SciTech Connect

    Morris, R.N.

    1998-08-01

    This report summarizes the results of the Gallium-Clad interactions Phase 3 and 4 tasks. Both tasks were to involve examining the out-of-pile stability of residual gallium in short fuel rods with an imposed thermal gradient. The thermal environment was to be created by an electrical heater in the center of the fuel rod and coolant flow on the rod outer cladding. Both tasks were canceled due to difficulties with fuel pellet fabrication, delays in the preparation of the test apparatus, and changes in the Fissile Materials Disposition program budget.

  17. Scientific developments ISFD3

    USGS Publications Warehouse

    Schropp, M.H.I.; Soong, T.W.

    2006-01-01

    Highlights, trends, and consensus from the 63 papers submitted to the Scientific Developments theme of the Third International Symposium on Flood Defence (ISFD) are presented. Realizing that absolute protection against flooding can never be guaranteed, trends in flood management have shifted: (1) from flood protection to flood-risk management, (2) from reinforcing structural protection to lowering flood levels, and (3) to sustainable management through integrated problem solving. Improved understanding of watershed responses, climate changes, applications of GIS and remote-sensing technologies, and advanced analytical tools appeared to be the driving forces for renewing flood-risk management strategies. Technical competence in integrating analytical tools to form the basin wide management systems are demonstrated by several large, transnation models. However, analyses from social-economic-environmental points of view are found lag in general. ?? 2006 Taylor & Francis Group.

  18. Task 3.0: Advanced power systems. Semi-annual report, April 1--June 30, 1993

    SciTech Connect

    McCollor, D.P.; Zygarlicke, C.J.; Mann, M.D.; Willson, W.G.; Hurley, J.P.

    1993-07-01

    A variety of activities are incorporated into the Advanced Power Systems program. Tasks included are (1) fuel utilization properties, (2) pressurized combustion, (3) catalytic gasification, and (4) hot-gas cleanup. ATRAN is stochastic and combines initial coal inorganics in a random manner in order to predict the resulting fly ash particle size and composition. ASHPERT, is an expert system yielding a first-order estimate of fly ash size and composition. Both models are designed to emulate pulverized-coal combustion. Input data required include identity, chemistry, size, quantity, and mineral-to-coal associations. The pressurized combustion task has focused on the construction of a versatile reactor system to simulate pressurized fluidized-bed combustion. Both castable and monolithic refractories have been investigated in determining slag prevention under a variety of conditions. Catalytic gasification coupled with a molten carbonate fuel cell offers an extremely efficient and environmentally sound power generating system using coal. Work with an Illinois No. 6 bituminous coal has not been successful. Continued efforts will focus on using the more reactive low-rank coals to try to achieve this goal. Hot-gas cleanup is the critical issue in many of the proposed advanced power system operations on coal. The key to successful ash removal is an understanding of the properties of the ash to be collected as well as the interactions of this material with the barrier itself. The knowledge base under development will assist in assessing many of these barrier material issues for a variety of coal ashes.

  19. The use of 2D and 3D information in a perceptual-cognitive judgement task.

    PubMed

    Put, Koen; Wagemans, Johan; Spitz, Jochim; Gallardo, Manuel Armenteros; Williams, A Mark; Helsen, Werner F

    2014-01-01

    We examined whether the use of three-dimensional (3D) simulations in an off-field offside decision-making task is beneficial compared to the more widely available two-dimensional (2D) simulations. Thirty-three assistant referees, who were all involved in professional football, participated in the experiment. They assessed 40 offside situations in both 2D and 3D formats using a counterbalanced design. A distinction was made between offside situations near (i.e., 15 m) and far (i.e., 30 m) from the touchline. Subsequently, a frame recognition task was performed in which assistant referees were asked to indicate which of the five pictures represented the previous video scene. A higher response accuracy score was observed under 3D (80.0%) compared to 2D (75.0%) conditions, in particular for the situations near the touchline (3D: 81.8%; 2D: 72.7%). No differences were reported between 2D and 3D in the frame recognition task. Findings suggest that in highly dynamic and complex situations, the visual system can benefit from the availability of 3D information, especially for relatively fine, metric position judgements. In the memory task, in which a mental abstraction had to be made from a dynamic situation to a static snapshot, 3D stereo disparities do not add anything over and beyond 2D simulations. The specific task demands should be taken into account when considering the most appropriate format for testing and training. PMID:24857384

  20. The use of 2D and 3D information in a perceptual-cognitive judgement task.

    PubMed

    Put, Koen; Wagemans, Johan; Spitz, Jochim; Gallardo, Manuel Armenteros; Williams, A Mark; Helsen, Werner F

    2014-01-01

    We examined whether the use of three-dimensional (3D) simulations in an off-field offside decision-making task is beneficial compared to the more widely available two-dimensional (2D) simulations. Thirty-three assistant referees, who were all involved in professional football, participated in the experiment. They assessed 40 offside situations in both 2D and 3D formats using a counterbalanced design. A distinction was made between offside situations near (i.e., 15 m) and far (i.e., 30 m) from the touchline. Subsequently, a frame recognition task was performed in which assistant referees were asked to indicate which of the five pictures represented the previous video scene. A higher response accuracy score was observed under 3D (80.0%) compared to 2D (75.0%) conditions, in particular for the situations near the touchline (3D: 81.8%; 2D: 72.7%). No differences were reported between 2D and 3D in the frame recognition task. Findings suggest that in highly dynamic and complex situations, the visual system can benefit from the availability of 3D information, especially for relatively fine, metric position judgements. In the memory task, in which a mental abstraction had to be made from a dynamic situation to a static snapshot, 3D stereo disparities do not add anything over and beyond 2D simulations. The specific task demands should be taken into account when considering the most appropriate format for testing and training.

  1. The Intersection of Task-Based Interaction, Task Complexity, and Working Memory: L2 Question Development through Recasts in a Laboratory Setting

    ERIC Educational Resources Information Center

    Kim, YouJin; Payant, Caroline; Pearson, Pamela

    2015-01-01

    The extent to which individual differences in cognitive abilities affect the relationship among task complexity, attention to form, and second language development has been addressed only minimally in the cognition hypothesis literature. The present study explores how reasoning demands in tasks and working memory (WM) capacity predict learners'…

  2. Concept definition for space station technology development experiments. Experiment definition, task 2

    NASA Technical Reports Server (NTRS)

    1986-01-01

    The second task of a study with the overall objective of providing a conceptual definition of the Technology Development Mission Experiments proposed by LaRC on space station is discussed. During this task, the information (goals, objectives, and experiment functional description) assembled on a previous task was translated into the actual experiment definition. Although still of a preliminary nature, aspects such as: environment, sensors, data acquisition, communications, handling, control telemetry requirements, crew activities, etc., were addressed. Sketches, diagrams, block diagrams, and timeline analyses of crew activities are included where appropriate.

  3. Assessing task importance and anxiety in medical school: an instrument development and initial validation study.

    PubMed

    Phillips, Henry L; Dong, Ting; Durning, Steven J; Artino, Anthony R

    2015-04-01

    Recent research in medical education suggests that students' motivational beliefs, such as their beliefs about the importance of a task, and their emotions are meaningful predictors of learning and performance. The primary purpose of this study was to develop a self-report measure of "task importance" and "anxiety" in relation to several medical education competencies and to collect validity evidence for the new measures. The secondary purpose was to evaluate differences in these measures by year of medical school. Exploratory factor analysis of scores from 368 medical school students suggested two task importance factors and three anxiety factors. The task importance and anxiety subscales were weakly related to each other and exhibited consistently negative and positive correlations, respectively, with three self-efficacy subscales. The task importance subscales were positively related to "metacognition," whereas "interpersonal skills anxiety" and "health knowledge anxiety" were positively related to "procrastination." All three anxiety factors were positively related to "avoidance of help seeking," whereas "interpersonal skills and professionalism importance" was negatively related to help avoidance behaviors. Finally, comparisons across the 4 years of medical school indicated that some aspects of task importance and anxiety varied significantly. Overall, findings from this study provide validity evidence for the psychometric quality of these scales, which capture task importance and anxiety in medical students. Limitations and implications for medical education research are discussed. PMID:25850124

  4. Task 3.0 -- Advanced power systems: Subtask 3.18 -- Ash behavior in power systems. Semi-annual report, June 1--December 31, 1997

    SciTech Connect

    Zygarlicke, C.J.; McCollor, D.P.; Folkedahl, B.C.; Swanson, M.L.; Musich, M.A.

    1998-10-01

    Advanced power systems such as integrated gasifier combined cycle systems and fluidized bed systems are at the forefront of power industry research because of the need for increased efficiency and the reduction of greenhouse gases. Ash behavior in power systems can have a significant impact on the design and performance of these systems. The Energy and Environmental Research Center (EERC) has developed a focused research initiative aimed at filling gaps in the understanding of fundamental mechanisms of ash behavior, which has relevance to commercial application and marketable products associated with advanced power systems. This program develops methods and means to better understand and mitigate adverse coal ash behavior in advanced power systems and can act to relieve the US reliance on diminishing recoverable oil resources and other greenhouse-producing fossil fuels. Subtask 3.18 is structured as three tasks. Task 1 pertains to summarizing the critical issues in ash behavior, especially for advanced power systems. Task 2 focuses on fundamental ash sintering and viscosity-ash composition relationships that are critical for developing a better mechanistic understanding of ash deposit formation and for predicting ash behavior. Task 3 is aimed primarily at determining the role of the ash chemistry and phase relationships for specific ash interactions in advanced power systems. The role of sulfides in the formation of ash deposits in gasification systems and the factors that influence alloy corrosion in supercritical boilers will be specifically analyzed. Task results to date are presented.

  5. From Tasking Purposes to Purposing Tasks; A Non-Marginal Role for Tasks; When and How the Language Development in TBI?

    ERIC Educational Resources Information Center

    Bruton, Anthony

    2002-01-01

    Presents contrasting views on the role and value of task-based learning. The first article is critiqued in the second article, and the original author responds to the critique in the third article. (Author/VWL)

  6. [Ocra Method: development of a new procedure for analysis of multiple tasks subject to infrequent rotation].

    PubMed

    Occhipinti, E; Colombini, Daniela; Occhipinti, M

    2008-01-01

    In the Ocra methods (Ocra index and Ocra Checklist), when computing the final indices (Ocra index or checklist score), in the case of more than one repetitive task a "traditional" procedure was already proposed, the results of which could be defined as "time-weighted average". This approach appears to be appropriate when considering rotations among tasks that are performed very frequently, for instance almost once every hour (or for shorter periods). However, when rotation among repetitive tasks is less frequent (i.e. once every 1 1/2 or more hours), the "time-weighted average" approach could result in an underestimation of the exposure level (as it practically flattens peaks of high exposures). For those scenarios an alternative approach based on the "most stressful task as minimum" might be more realistic. This latter approach has already been included in the NIOSH approach for multiple sequential lifting tasks and, given the recent availability in the Ocra method of more detailed duration multipliers (practically one different Du(M) for each different step of one hour of duration of the repetitive task), it is now possible to define a particular procedure to compute the complex Ocra Multitask Index (cOCRA) and the complex Checklist Score (cCHESCO) for the analysis of two or more repetitive tasks when rotations are infrequent (rotations every 1 1/2 hours or more). The result of this approach will be at least equal to the index of the most stressful task considered for its individual daily duration and at the most equal to the index of the most stressful task when it is (only theoretically) considered as lasting for the overall daily duration of all examined repetitive tasks. The procedure is based on the following formula: Complex Ocra Multitask Index = Ocra(1(Dum1) + (Delta ocra1xK) where 1,2,3,...,N = repetitive tasks ordered by ocra index values (1 = highest; N = lowest) computed considering respective real duration multipliers (Dum(i)). ocra1 = ocra index of

  7. Silicon Ingot Casting - Heat Exchanger Method Multi-wire Slicing - Fixed Abrasive Slicing Technique. Phase 3 Silicon Sheet Growth Development for the Large Area Sheet Task of the Low-cost Solar Array Project

    NASA Technical Reports Server (NTRS)

    Schmid, F.; Khattak, C. P.

    1979-01-01

    Several 20 cm diameter silicon ingots, up to 6.3 kg. were cast with good crystallinity. The graphite heat zone can be purified by heating it to high temperatures in vacuum. This is important in reducing costs and purification of large parts. Electroplated wires with 45 um synthetic diamonds and 30 um natural diamonds showed good cutting efficiency and lifetime. During slicing of a 10 cm x 10 cm workpiece, jerky motion occurred in the feed and rocking mechanisms. This problem is corrected and modifications were made to reduce the weight of the bladeheat by 50%.

  8. Development and Confirmatory Factory Analysis of the Achievement Task Value Scale for University Students

    ERIC Educational Resources Information Center

    Lou, Yu-Chiung; Lin, Hsiao-Fang; Lin, Chin-Wen

    2013-01-01

    The aims of the study were (a) to develop a scale to measure university students' task value and (b) to use confirmatory factor analytic techniques to investigate the construct validity of the scale. The questionnaire items were developed based on theoretical considerations and the final version contained 38 items divided into 4 subscales.…

  9. The Development of Procedural Knowledge in Adults Engaged in a Tractor-Trailer Task.

    ERIC Educational Resources Information Center

    Moses, Nelson

    1994-01-01

    Studied development of procedural knowledge in 14 adults, aged 18 to 35 years, engaged in a novel task using a toy tractor-trailer rig. Results revealed three phases of development in subjects' knowledge of steering procedures and the rig's movement patterns, and their use of feedback information. Subjects also manifested different levels of…

  10. Mining and Minerals Technical Advisory Committee on Curriculum Development. Job Clusters, Competencies and Task Analysis.

    ERIC Educational Resources Information Center

    Northern Montana Coll., Havre. Montana Center for Vocational Education, Research, Curriculum and Personnel Development.

    This skills inventory for mining occupations was developed by a technical committee in Montana to assist in the development of model curricula and to address state labor market needs. The committee included employers from the mining industry, members of trade and professional associations, and educators. The validated task list and defined job…

  11. Development of Situational Task Methodology for the Evaluation of Process Outcomes in the Open Classroom.

    ERIC Educational Resources Information Center

    Rentfrow, Robert K.; And Others

    The purpose of this research was to develop an evaluation technique to assess how effectively children develop as independent learners within classrooms implementing the Tucson Early Education Model. A situational task was chosen in order to gather information about the ongoing open classroom. The Classroom Attitude Observation Schedule was…

  12. Forestry Technical Advisory Committee on Curriculum Development. Job Clusters, Competencies and Task Analysis.

    ERIC Educational Resources Information Center

    Northern Montana Coll., Havre. Montana Center for Vocational Education, Research, Curriculum and Personnel Development.

    This skills inventory for forestry occupations was developed by a technical committee in Montana to assist in the development of model curricula and to address state labor market needs. The committee included employers from the forestry industry, members from trade and professional associations, and educators. The validated task list and defined…

  13. Metacognitive Development of Deaf Children: Lessons from the Appearance-Reality and False Belief Tasks

    ERIC Educational Resources Information Center

    Courtin, Cyril; Melot, Anne-Marie

    2005-01-01

    "Theory of mind" development is now an important research field in deaf studies. Past research with the classic false belief task has consistently reported a delay in theory of mind development in deaf children born of hearing parents, while performance of second-generation deaf children is more problematic with some contradictory results. The…

  14. The effects of task difficulty on visual search strategy in virtual 3D displays.

    PubMed

    Pomplun, Marc; Garaas, Tyler W; Carrasco, Marisa

    2013-01-01

    Analyzing the factors that determine our choice of visual search strategy may shed light on visual behavior in everyday situations. Previous results suggest that increasing task difficulty leads to more systematic search paths. Here we analyze observers' eye movements in an "easy" conjunction search task and a "difficult" shape search task to study visual search strategies in stereoscopic search displays with virtual depth induced by binocular disparity. Standard eye-movement variables, such as fixation duration and initial saccade latency, as well as new measures proposed here, such as saccadic step size, relative saccadic selectivity, and x-y target distance, revealed systematic effects on search dynamics in the horizontal-vertical plane throughout the search process. We found that in the "easy" task, observers start with the processing of display items in the display center immediately after stimulus onset and subsequently move their gaze outwards, guided by extrafoveally perceived stimulus color. In contrast, the "difficult" task induced an initial gaze shift to the upper-left display corner, followed by a systematic left-right and top-down search process. The only consistent depth effect was a trend of initial saccades in the easy task with smallest displays to the items closest to the observer. The results demonstrate the utility of eye-movement analysis for understanding search strategies and provide a first step toward studying search strategies in actual 3D scenarios. PMID:23986539

  15. The effects of task difficulty on visual search strategy in virtual 3D displays.

    PubMed

    Pomplun, Marc; Garaas, Tyler W; Carrasco, Marisa

    2013-08-28

    Analyzing the factors that determine our choice of visual search strategy may shed light on visual behavior in everyday situations. Previous results suggest that increasing task difficulty leads to more systematic search paths. Here we analyze observers' eye movements in an "easy" conjunction search task and a "difficult" shape search task to study visual search strategies in stereoscopic search displays with virtual depth induced by binocular disparity. Standard eye-movement variables, such as fixation duration and initial saccade latency, as well as new measures proposed here, such as saccadic step size, relative saccadic selectivity, and x-y target distance, revealed systematic effects on search dynamics in the horizontal-vertical plane throughout the search process. We found that in the "easy" task, observers start with the processing of display items in the display center immediately after stimulus onset and subsequently move their gaze outwards, guided by extrafoveally perceived stimulus color. In contrast, the "difficult" task induced an initial gaze shift to the upper-left display corner, followed by a systematic left-right and top-down search process. The only consistent depth effect was a trend of initial saccades in the easy task with smallest displays to the items closest to the observer. The results demonstrate the utility of eye-movement analysis for understanding search strategies and provide a first step toward studying search strategies in actual 3D scenarios.

  16. Construction of tasks in order to develop and promote classroom communication in mathematics

    NASA Astrophysics Data System (ADS)

    Olteanu, Lucian

    2015-02-01

    In this article, the focus is on task construction and the importance of this process to develop and promote classroom communication in mathematics. The students' tests, examination of students' mathematical work, the teachers' lesson plans, and reports of the lessons' instructions are the basic data for this article. The analysis indicated that teachers develop their professional decision-makers through developing the ability to construct relevant tasks for identifying the critical aspects in students' learning. The findings suggest that construction of tasks can be a productive basis in helping teachers to make fundamental changes in their understanding of what they should focus on in a teaching situation to improve mathematical communication. In this process, the teachers integrate, in a natural way, the research results from mathematics education.

  17. 75 FR 24781 - Task Force on Space Industry Workforce and Economic Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-06

    ...#0;#0; #0; #0;Title 3-- #0;The President ] Memorandum of May 3, 2010 Task Force on Space Industry... Business Administration the Administrator of the National Aeronautics and Space Administration the Chair of... National Aeronautics and Space Administration's (NASA) budget over the next 5 years, this strategy...

  18. EQ3/6 geochemical modeling task plan for Nevada Nuclear Waste Storage Investigations (NNWSI)

    SciTech Connect

    Isherwood, D.; Wolery, T.

    1984-04-10

    This task plan outlines work needed to upgrade the EQ3/6 geochemical code and expand the supporting data bases to allow the Nevada Nuclear Waste Storage Investigations (NNWSI) to model chemical processes important to the storage of nuclear waste in a tuff repository in the unsaturated zone. The plan covers the fiscal years 1984 to 1988. The scope of work includes the development of sub-models in the EQ3/6 code package for studying the effects of sorption, precipitation kinetics, redox disequilibrium, and radiolysis on radionuclide speciation and solubility. The work also includes a glass/water interactions model and a geochemical flow model which will allow us to study waste form leaching and reactions involving the waste package. A special emphasis is placed on verification of new capabilities as they are developed and code documentation to meet NRC requirements. Data base expansion includes the addition of elements and associated aqueous species and solid phases that are specific to nuclear waste (e.g., actinides and fission products) and the upgrading and documentation of the thermodynamic data for other species of interest.

  19. A task-oriented modular and agent-based collaborative design mechanism for distributed product development

    NASA Astrophysics Data System (ADS)

    Liu, Jinfei; Chen, Ming; Wang, Lei; Wu, Qidi

    2014-05-01

    The rapid expansion of enterprises makes product collaborative design (PCD) a critical issue under the distributed heterogeneous environment, but as the collaborative task of large-scale network becomes more complicated, neither unified task decomposition and allocation methodology nor Agent-based network management platform can satisfy the increasing demands. In this paper, to meet requirements of PCD for distributed product development, a collaborative design mechanism based on the thought of modularity and the Agent technology is presented. First, the top-down 4-tier process model based on task-oriented modular and Agent is constructed for PCD after analyzing the mapping relationships between requirements and functions in the collaborative design. Second, on basis of sub-task decomposition for PCD based on a mixed method, the mathematic model of task-oriented modular based on multi-objective optimization is established to maximize the module cohesion degree and minimize the module coupling degree, while considering the module executable degree as a restriction. The mathematic model is optimized and simulated by the modified PSO, and the decomposed modules are obtained. Finally, the Agent structure model for collaborative design is put forward, and the optimism matching Agents are selected by using similarity algorithm to implement different task-modules by the integrated reasoning and decision-making mechanism with the behavioral model of collaborative design Agents. With the results of experimental studies for automobile collaborative design, the feasibility and efficiency of this methodology of task-oriented modular and Agent-based collaborative design in the distributed heterogeneous environment are verified. On this basis, an integrative automobile collaborative R&D platform is developed. This research provides an effective platform for automobile manufacturing enterprises to achieve PCD, and helps to promote product numeralization collaborative R&D and

  20. Development and evaluation of a predictive algorithm for telerobotic task complexity

    NASA Technical Reports Server (NTRS)

    Gernhardt, M. L.; Hunter, R. C.; Hedgecock, J. C.; Stephenson, A. G.

    1993-01-01

    There is a wide range of complexity in the various telerobotic servicing tasks performed in subsea, space, and hazardous material handling environments. Experience with telerobotic servicing has evolved into a knowledge base used to design tasks to be 'telerobot friendly.' This knowledge base generally resides in a small group of people. Written documentation and requirements are limited in conveying this knowledge base to serviceable equipment designers and are subject to misinterpretation. A mathematical model of task complexity based on measurable task parameters and telerobot performance characteristics would be a valuable tool to designers and operational planners. Oceaneering Space Systems and TRW have performed an independent research and development project to develop such a tool for telerobotic orbital replacement unit (ORU) exchange. This algorithm was developed to predict an ORU exchange degree of difficulty rating (based on the Cooper-Harper rating used to assess piloted operations). It is based on measurable parameters of the ORU, attachment receptacle and quantifiable telerobotic performance characteristics (e.g., link length, joint ranges, positional accuracy, tool lengths, number of cameras, and locations). The resulting algorithm can be used to predict task complexity as the ORU parameters, receptacle parameters, and telerobotic characteristics are varied.

  1. Development and evaluation of task-specific NLP framework in China.

    PubMed

    Ge, Caixia; Zhang, Yinsheng; Huang, Zhenzhen; Jia, Zheng; Ju, Meizhi; Duan, Huilong; Li, Haomin

    2015-01-01

    Natural language processing (NLP) has been designed to convert narrative text into structured data. Although some general NLP architectures have been developed, a task-specific NLP framework to facilitate the effective use of data is still a challenge in lexical resource limited regions, such as China. The purpose of this study is to design and develop a task-specific NLP framework to extract targeted information from particular documents by adopting dedicated algorithms on current limited lexical resources. In this framework, a shared and evolving ontology mechanism was designed. The result has shown that such a free text driven platform will accelerate the NLP technology acceptance in China.

  2. Utilization Assessment of Target Electrification Vehicles at Naval Air Station Whidbey Island: Task 3

    SciTech Connect

    Schey, Steve

    2015-05-01

    Several U.S. Department of Defense based studies have been conducted to identify potential U.S. Department of Defense transportation systems that are strong candidates for introduction or expansion of plug-in electric vehicles (PEVs). Task 2 involved identifying daily operational characteristics of select vehicles and initiating data logging of vehicle movements in order to characterize the vehicle’s mission. Individual observations of these selected vehicles provide the basis for recommendations related to PEV adoption and whether a battery electric vehicle or plug-in hybrid electric vehicle (collectively referred to as PEVs) can fulfill the mission requirements and provide observations related to placement of PEV charging infrastructure. This report provides the results of the data analysis and observations related to replacement of current vehicles with PEVs. This fulfills part of the Task 3 requirements. Task 3 also includes an assessment of the charging infrastructure required to support this replacement, which is the subject of a separate report.

  3. Development of statistical models for predicting muscle and mental activities during repetitive precision tasks.

    PubMed

    Zadry, Hilma Raimona; Dawal, Siti Zawiah Md; Taha, Zahari

    2016-09-01

    This study was conducted to develop muscle and mental activities on repetitive precision tasks. A laboratory experiment was used to address the objectives. Surface electromyography was used to measure muscle activities from eight upper limb muscles, while electroencephalography recorded mental activities from six channels. Fourteen university students participated in the study. The results show that muscle and mental activities increase for all tasks, indicating the occurrence of muscle and mental fatigue. A linear relationship between muscle activity, mental activity and time was found while subjects were performing the task. Thus, models were developed using those variables. The models were found valid after validation using other students' and workers' data. Findings from this study can contribute as a reference for future studies investigating muscle and mental activity and can be applied in industry as guidelines to manage muscle and mental fatigue, especially to manage job schedules and rotation. PMID:27053140

  4. HANFORD CONTAINERIZED CAST STONE FACILITY TASK 1 PROCESS TESTING & DEVELOPMENT FINAL TEST REPORT

    SciTech Connect

    LOCKREM, L L

    2005-07-13

    Laboratory testing and technical evaluation activities on Containerized Cast Stone (CCS) were conducted under the Scope of Work (SOW) contained in CH2M HILL Hanford Group, Inc. (CHG) Contract No. 18548 (CHG 2003a). This report presents the results of testing and demonstration activities discussed in SOW Section 3.1, Task I--''Process Development Testing'', and described in greater detail in the ''Containerized Grout--Phase I Testing and Demonstration Plan'' (CHG, 2003b). CHG (2003b) divided the CCS testing and evaluation activities into six categories, as follows: (1) A short set of tests with simulant to select a preferred dry reagent formulation (DRF), determine allowable liquid addition levels, and confirm the Part 2 test matrix. (2) Waste form performance testing on cast stone made from the preferred DRF and a backup DRF, as selected in Part I, and using low activity waste (LAW) simulant. (3) Waste form performance testing on cast stone made from the preferred DRF using radioactive LAW. (4) Waste form validation testing on a selected nominal cast stone formulation using the preferred DRF and LAW simulant. (5) Engineering evaluations of explosive/toxic gas evolution, including hydrogen, from the cast stone product. (6) Technetium ''getter'' testing with cast stone made with LAW simulant and with radioactive LAW. In addition, nitrate leaching observations were drawn from nitrate leachability data obtained in the course of the Parts 2 and 3 waste form performance testing. The nitrate leachability index results are presented along with other data from the applicable activity categories.

  5. Enhancing the Executive Functions of 3-Year-Olds in the Dimensional Change Card Sort Task

    ERIC Educational Resources Information Center

    Perone, Sammy; Molitor, Stephen J.; Buss, Aaron T.; Spencer, John P.; Samuelson, Larissa K.

    2015-01-01

    Executive functions enable flexible thinking, something young children are notoriously bad at. For instance, in the dimensional change card sort (DCCS) task, 3-year-olds can sort cards by one dimension (shape), but continue to sort by this dimension when asked to switch (to color). This study tests a prediction of a dynamic neural field model that…

  6. Materials for Advanced Ultrasupercritical Steam Turbines Task 4: Cast Superalloy Development

    SciTech Connect

    Thangirala, Mani

    2015-09-30

    The Steam Turbine critical stationary structural components are high integrity Large Shell and Valve Casing heavy section Castings, containing high temperature steam under high pressures. Hence to support the development of advanced materials technology for use in an AUSC steam turbine capable of operating with steam conditions of 760°C (1400°F) and 35 Mpa (5000 psia), Casting alloy selection and evaluation of mechanical, metallurgical properties and castability with robust manufacturing methods are mandated. Alloy down select from Phase 1 based on producability criteria and creep rupture properties tested by NETL-Albany and ORNL directed the consortium to investigate cast properties of Haynes 282 and Haynes 263. The goals of Task 4 in Phase 2 are to understand a broader range of mechanical properties, the impact of manufacturing variables on those properties. Scale up the size of heats to production levels to facilitate the understanding of the impact of heat and component weight, on metallurgical and mechanical behavior. GE Power & Water Materials and Processes Engineering for the Phase 2, Task 4.0 Castings work, systematically designed and executed casting material property evaluation, multiple test programs. Starting from 15 lbs. cylinder castings to world’s first 17,000 lbs. poured weight, heavy section large steam turbine partial valve Haynes 282 super alloy casting. This has demonstrated scalability of the material for steam Turbine applications. Activities under Task 4.0, Investigated and characterized various mechanical properties of Cast Haynes 282 and Cast Nimonic 263. The development stages involved were: 1) Small Cast Evaluation: 4 inch diam. Haynes 282 and Nimonic 263 Cylinders. This provided effects of liquidus super heat range and first baseline mechanical data on cast versions of conventional vacuum re-melted and forged Ni based super alloys. 2) Step block castings of 300 lbs. and 600 lbs. Haynes 282 from 2 foundry heats were evaluated which

  7. Spacelab cost reduction alternatives study. Volume 3: Crew training task analysis

    NASA Technical Reports Server (NTRS)

    1975-01-01

    The on-orbit phase of flight was analyzed to identify the functions that had to be performed to meet flight objectives. The functions identified were combined into a top-level functional flow diagram (3.0 On-Orbit Operations). Each function, in turn, was analyzed to determine the major activities necessary to perform the function. The activities and activity sequences were presented in second level functional flow diagrams. Each major activity was further analyzed to define the operator tasks that are performed to accomplish that activity. Training analysis worksheets were used to document the analysis of each function down to the task level and provide training requirements data for each task. For Vol. 1, see N76-24315.

  8. Job Tasks Performed by Career Preparation System Administrators in One Midwestern State: Implications for Leadership Development

    ERIC Educational Resources Information Center

    VanderMolen, Julia; Zinzer, Richard

    2009-01-01

    There is a need to prepare new leaders in Career and Technical Education due to retirements and because the job demands have changed over the years. In order to verify the curriculum for leadership development programs, a study was conducted to measure the importance and frequency of job tasks performed by Career Preparation System administrators…

  9. Lubrication Specialist: Task List and Competency Record. Developed for Vocational-Technical Curriculum Articulation in Minnesota.

    ERIC Educational Resources Information Center

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    Intended for the vocational instructor, the booklet presents a task list and competency record for the occupational program of lubrication specialist. The list was developed by a working committee of auto mechanics instructors and industry representatives throughout the state of Minnesota for use in program articulation between secondary and…

  10. Development of the Biology Card Sorting Task to Measure Conceptual Expertise in Biology

    ERIC Educational Resources Information Center

    Smith, Julia I.; Combs, Elijah D.; Nagami, Paul H.; Alto, Valerie M.; Goh, Henry G.; Gourdet, Muryam A. A.; Hough, Christina M.; Nickell, Ashley E.; Peer, Adrian G.; Coley, John D.; Tanner, Kimberly D.

    2013-01-01

    There are widespread aspirations to focus undergraduate biology education on teaching students to think conceptually like biologists; however, there is a dearth of assessment tools designed to measure progress from novice to expert biological conceptual thinking. We present the development of a novel assessment tool, the Biology Card Sorting Task,…

  11. The Development of an Individuals-within-Dyads Multilevel Performance Measure for an Interactive Cheerleading Task

    ERIC Educational Resources Information Center

    Habeeb, Christine M.; Eklund, Robert C.

    2016-01-01

    Dyadic interactions generate direct relationships in which interdependent sport behaviors can be destructured. The focus of this investigation was to develop a two-level performance framework and corresponding measures of individual- and dyad-level sport performance. The described procedures surrounded a male-female cheerleading paired-stunt task,…

  12. An Exploratory Study of the Role of Task Dependence on Team Captains' Leadership Development

    ERIC Educational Resources Information Center

    Grandzol, Christian J.

    2011-01-01

    While there is evidence that team captainship in intercollegiate sports can lead to leadership development, there is little evidence about the role that task dependence may play on that effect. The individual or team nature of sports may offer different leadership experiences for team captains, leading to differential outcomes. In this exploratory…

  13. The Role of Context in a Collaborative Problem-Solving Task during Professional Development

    ERIC Educational Resources Information Center

    Ritella, Giuseppe; Ligorio, Maria Beatrice; Hakkarainen, Kai

    2016-01-01

    This article analyses how a group of teachers managed the resources available while performing computer-supported collaborative problem-solving tasks in the context of professional development. The authors video-recorded and analysed collaborative sessions during which the group of teachers used a digital environment to prepare a pedagogical…

  14. Construction of Tasks in Order to Develop and Promote Classroom Communication in Mathematics

    ERIC Educational Resources Information Center

    Olteanu, Lucian

    2015-01-01

    In this article, the focus is on task construction and the importance of this process to develop and promote classroom communication in mathematics. The students' tests, examination of students' mathematical work, the teachers' lesson plans, and reports of the lessons' instructions are the basic data for this article. The…

  15. Probing behavioral responses to food: Development of a food-specific go/no-go task

    PubMed Central

    Teslovich, Theresa; Friedl, Eve K.; Kostro, Katrina; Weigel, Julia; Davidow, Juliet Y.; Riddle, Megan C.; Rosenbaum, Michael; Walsh, B. Timothy; Casey, BJ; Mayer, Laurel

    2014-01-01

    The ability to exert self-control in the face of appetitive, alluring cues is a critical component of healthy development. The development of behavioral measures that use disease-relevant stimuli can greatly improve our understanding of cue-specific impairments in self-control. To produce such a tool relevant to the study of eating and weight disorders, we modified the traditional go/no-go task to include food and non-food targets. To confirm that performance on this new task was consistent with other go/no-go tasks, it was given to147 healthy, normal weight volunteers between the ages of 5 and 30. High-resolution photos of food or toys were used as the target and nontarget stimuli. Consistent with expectations, overall improvements in accuracy were seen from childhood to adulthood. Participants responded more quickly and made more commission errors to food cues compared to nonfood cues (F(1,140) = 21.76, P<0.001), although no behavioral differences were seen between lowand high-calorie food cues for this non-obese, healthy developmental sample. This novel food-specific go/no-go task may be used to track the development of self-control in the context of food cues and to evaluate deviations or deficits in the development of this ability in individuals at risk for eating problem behaviors and disorders. PMID:24909971

  16. Florida Model Task Force on Diabetic Retinopathy: Development of an Interagency Network.

    ERIC Educational Resources Information Center

    Groff, G.; And Others

    1990-01-01

    This article describes the development of a mechanism to organize a network in Florida for individuals who are at risk for diabetic retinopathy. The task force comprised representatives from governmental, academic, professional, and voluntary organizations. It worked to educate professionals, patients, and the public through brochures, resource…

  17. Automotive Mechanic: Task List and Competency Record. Developed for Vocational-Technical Curriculum Articulation in Minnesota.

    ERIC Educational Resources Information Center

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    Intended for the vocational instructor, the booklet presents a task list and competency record for the occupational program of automotive mechanic. The list was developed by a working committee of auto mechanics instructors and industry representatives throughout the state of Minnesota for use in program articulation between secondary and…

  18. Cognitive Developmental Level Gender, and the Development of Learned Helplessness on Mathematical Calculation and Reasoning Tasks.

    ERIC Educational Resources Information Center

    Monaco, Nanci M.; Gentile, J. Ronald

    1987-01-01

    This study was designed to test whether a learned helplessness treatment would decrease performance on mathematical tasks and to extend learned helplessness findings to include the cognitive development dimension. Results showed no differential advantages to either sex in resisting effects of learned helplessness or in benefiting from strategy…

  19. Probing behavioral responses to food: development of a food-specific go/no-go task.

    PubMed

    Teslovich, Theresa; Freidl, Eve K; Kostro, Katrina; Weigel, Julia; Davidow, Juliet Y; Riddle, Megan C; Helion, Chelsea; Dreyfuss, Michael; Rosenbaum, Michael; Walsh, B Timothy; Casey, Betty Jo; Mayer, Laurel

    2014-09-30

    The ability to exert self-control in the face of appetitive, alluring cues is a critical component of healthy development. The development of behavioral measures that use disease-relevant stimuli can greatly improve our understanding of cue-specific impairments in self-control. To produce such a tool relevant to the study of eating and weight disorders, we modified the traditional go/no-go task to include food and non-food targets. To confirm that performance on this new task was consistent with other go/no-go tasks, it was given to 147 healthy, normal weight volunteers between the ages of 5 and 30. High-resolution photos of food or toys were used as the target and nontarget stimuli. Consistent with expectations, overall improvements in accuracy were seen from childhood to adulthood. Participants responded more quickly and made more commission errors to food cues compared to nonfood cues (F(1,140)=21.76, P<0.001), although no behavioral differences were seen between low- and high-calorie food cues for this non-obese, healthy developmental sample. This novel food-specific go/no-go task may be used to track the development of self-control in the context of food cues and to evaluate deviations or deficits in the development of this ability in individuals at risk for eating problem behaviors and disorders. PMID:24909971

  20. Probing behavioral responses to food: development of a food-specific go/no-go task.

    PubMed

    Teslovich, Theresa; Freidl, Eve K; Kostro, Katrina; Weigel, Julia; Davidow, Juliet Y; Riddle, Megan C; Helion, Chelsea; Dreyfuss, Michael; Rosenbaum, Michael; Walsh, B Timothy; Casey, Betty Jo; Mayer, Laurel

    2014-09-30

    The ability to exert self-control in the face of appetitive, alluring cues is a critical component of healthy development. The development of behavioral measures that use disease-relevant stimuli can greatly improve our understanding of cue-specific impairments in self-control. To produce such a tool relevant to the study of eating and weight disorders, we modified the traditional go/no-go task to include food and non-food targets. To confirm that performance on this new task was consistent with other go/no-go tasks, it was given to 147 healthy, normal weight volunteers between the ages of 5 and 30. High-resolution photos of food or toys were used as the target and nontarget stimuli. Consistent with expectations, overall improvements in accuracy were seen from childhood to adulthood. Participants responded more quickly and made more commission errors to food cues compared to nonfood cues (F(1,140)=21.76, P<0.001), although no behavioral differences were seen between low- and high-calorie food cues for this non-obese, healthy developmental sample. This novel food-specific go/no-go task may be used to track the development of self-control in the context of food cues and to evaluate deviations or deficits in the development of this ability in individuals at risk for eating problem behaviors and disorders.

  1. Negative Feedback and Positive Evidence in Task-Based Interaction: Differential Effects on L2 Development

    ERIC Educational Resources Information Center

    Iwashita, Noriko

    2003-01-01

    This study examines the role of task-based conversation in second language (L2) grammatical development, focusing on the short-term effects of both negative feedback and positive evidence on the acquisition of two Japanese structures. The data are drawn from 55 L2 learners of Japanese at a beginning level of proficiency in an Australian tertiary…

  2. Standardization and adult norms for the sequential subtracting tasks of serial 3's and 7's.

    PubMed

    Bristow, Thomas; Jih, Chwan-Shyang; Slabich, Artrina; Gunn, Jamie

    2016-01-01

    The Serial 3's and 7's subtraction tasks are traditionally used in mental status examinations. The usefulness of these tasks is based upon the assumption that they measure attention and mental concentration. However, there is no uniform method of administration, and there are no recognized norms for these subtraction tasks, which has led some in the field of psychiatry and neuropsychology to conclude that the tests are not useful. The purpose of this research had three goals: (a) to create a standardization of the administration, (b) to provide a structured and consistent framework for the data evaluation, and (c) to create adult norms as a frame of reference for interpretation. The study investigated normal control subjects (N = 204) and specific variables of interest included both efficiency and accuracy of performance. The results demonstrated that when used conjointly, Serial 3's and Serial 7's are an efficient and accurate measure of sequential subtracting, but even more importantly, the study revealed the hierarchical increase in cognitive demand when the performances between 3's and 7's were compared. With standardization and norms, serial subtraction becomes a more effective screening technique within the context of a mental status examination. Similarly, the conjoint administration of these tasks yields synergistic data that can be useful in determining deficits in the cognitive domains of attention and working memory. PMID:27218700

  3. Developing Bayesian adaptive methods for estimating sensitivity thresholds (d') in Yes-No and forced-choice tasks.

    PubMed

    Lesmes, Luis A; Lu, Zhong-Lin; Baek, Jongsoo; Tran, Nina; Dosher, Barbara A; Albright, Thomas D

    2015-01-01

    Motivated by Signal Detection Theory (SDT), we developed a family of novel adaptive methods that estimate the sensitivity threshold-the signal intensity corresponding to a pre-defined sensitivity level (d' = 1)-in Yes-No (YN) and Forced-Choice (FC) detection tasks. Rather than focus stimulus sampling to estimate a single level of %Yes or %Correct, the current methods sample psychometric functions more broadly, to concurrently estimate sensitivity and decision factors, and thereby estimate thresholds that are independent of decision confounds. Developed for four tasks-(1) simple YN detection, (2) cued YN detection, which cues the observer's response state before each trial, (3) rated YN detection, which incorporates a Not Sure response, and (4) FC detection-the qYN and qFC methods yield sensitivity thresholds that are independent of the task's decision structure (YN or FC) and/or the observer's subjective response state. Results from simulation and psychophysics suggest that 25 trials (and sometimes less) are sufficient to estimate YN thresholds with reasonable precision (s.d. = 0.10-0.15 decimal log units), but more trials are needed for FC thresholds. When the same subjects were tested across tasks of simple, cued, rated, and FC detection, adaptive threshold estimates exhibited excellent agreement with the method of constant stimuli (MCS), and with each other. These YN adaptive methods deliver criterion-free thresholds that have previously been exclusive to FC methods.

  4. The Development of Landmark and Beacon Use in Young Children: Evidence from a Touchscreen Search Task

    ERIC Educational Resources Information Center

    Sutton, Jennifer E.

    2006-01-01

    Children ages 2, 3 and 4 years participated in a novel hide-and-seek search task presented on a touchscreen monitor. On beacon trials, the target hiding place could be located using a beacon cue, but on landmark trials, searching required the use of a nearby landmark cue. In Experiment 1, 2-year-olds performed less accurately than older children…

  5. Adolescents' Performance on the Iowa Gambling Task: Implications for the Development of Decision Making and Ventromedial Prefrontal Cortex

    ERIC Educational Resources Information Center

    Hooper, Catalina J.; Luciana, Monica; Conklin, Heather M.; Yarger, Rebecca S.

    2004-01-01

    Healthy adolescents (79 girls, 66 boys), ages 9-17, completed the Iowa Gambling Task (IGT; A. Bechara, A. R. Damasio, H. Damasio, & S. W. Anderson, 1994) as well as working memory (digit span) and behavioral inhibition (go/no-go) tasks. Cross-sectional age-related changes were seen on all 3 tasks. Gender differences were seen in IGT deck…

  6. The Effect of N-3 on N-2 Repetition Costs in Task Switching

    ERIC Educational Resources Information Center

    Schuch, Stefanie; Grange, James A.

    2015-01-01

    N-2 task repetition cost is a response time and error cost returning to a task recently performed after one intervening trial (i.e., an ABA task sequence) compared with returning to a task not recently performed (i.e., a CBA task sequence). This cost is considered a robust measure of inhibitory control during task switching. The present article…

  7. Enhancing the executive functions of 3-year-olds in the dimensional change card sort task

    PubMed Central

    Perone, Sammy; Molitor, Stephen; Buss, Aaron T.; Spencer, John P.; Samuelson, Larissa K.

    2015-01-01

    Executive functions (EFs) enable flexible thinking, something young children are notoriously bad at. For instance, in the dimensional change card sort (DCCS) task, 3-year-olds can sort cards by one dimension (shape), but continue to sort by this dimension when asked to switch (to color). This study tests a prediction of a Dynamic Neural Field (DNF) model that prior experience with the post-switch dimension can enhance 3-year-old’s performance in the DCCS task. In Experiment 1A, a matching game was used to pre-expose 3-year-olds (n=36) to color. This facilitated switching from sorting by shape to color. In Experiment 1B, 3-year-olds (n=18) were pre-exposed to shape. This did not facilitate switching from sorting by color to shape. The DNF model was used to provide a mechanistic explanation for this asymmetry. PMID:25441395

  8. Development of the Biology Card Sorting Task to Measure Conceptual Expertise in Biology

    PubMed Central

    Smith, Julia I.; Combs, Elijah D.; Nagami, Paul H.; Alto, Valerie M.; Goh, Henry G.; Gourdet, Muryam A. A.; Hough, Christina M.; Nickell, Ashley E.; Peer, Adrian G.; Coley, John D.; Tanner, Kimberly D.

    2013-01-01

    There are widespread aspirations to focus undergraduate biology education on teaching students to think conceptually like biologists; however, there is a dearth of assessment tools designed to measure progress from novice to expert biological conceptual thinking. We present the development of a novel assessment tool, the Biology Card Sorting Task, designed to probe how individuals organize their conceptual knowledge of biology. While modeled on tasks from cognitive psychology, this task is unique in its design to test two hypothesized conceptual frameworks for the organization of biological knowledge: 1) a surface feature organization focused on organism type and 2) a deep feature organization focused on fundamental biological concepts. In this initial investigation of the Biology Card Sorting Task, each of six analytical measures showed statistically significant differences when used to compare the card sorting results of putative biological experts (biology faculty) and novices (non–biology major undergraduates). Consistently, biology faculty appeared to sort based on hypothesized deep features, while non–biology majors appeared to sort based on either surface features or nonhypothesized organizational frameworks. Results suggest that this novel task is robust in distinguishing populations of biology experts and biology novices and may be an adaptable tool for tracking emerging biology conceptual expertise. PMID:24297290

  9. Development of the biology card sorting task to measure conceptual expertise in biology.

    PubMed

    Smith, Julia I; Combs, Elijah D; Nagami, Paul H; Alto, Valerie M; Goh, Henry G; Gourdet, Muryam A A; Hough, Christina M; Nickell, Ashley E; Peer, Adrian G; Coley, John D; Tanner, Kimberly D

    2013-01-01

    There are widespread aspirations to focus undergraduate biology education on teaching students to think conceptually like biologists; however, there is a dearth of assessment tools designed to measure progress from novice to expert biological conceptual thinking. We present the development of a novel assessment tool, the Biology Card Sorting Task, designed to probe how individuals organize their conceptual knowledge of biology. While modeled on tasks from cognitive psychology, this task is unique in its design to test two hypothesized conceptual frameworks for the organization of biological knowledge: 1) a surface feature organization focused on organism type and 2) a deep feature organization focused on fundamental biological concepts. In this initial investigation of the Biology Card Sorting Task, each of six analytical measures showed statistically significant differences when used to compare the card sorting results of putative biological experts (biology faculty) and novices (non-biology major undergraduates). Consistently, biology faculty appeared to sort based on hypothesized deep features, while non-biology majors appeared to sort based on either surface features or nonhypothesized organizational frameworks. Results suggest that this novel task is robust in distinguishing populations of biology experts and biology novices and may be an adaptable tool for tracking emerging biology conceptual expertise.

  10. LNG Safety Research: FEM3A Model Development

    SciTech Connect

    Iraj A. Salehi; Jerry Havens; Tom Spicer

    2006-09-30

    This quarterly report for DE-FG26-04NT42030 covers a period from July 1, 2006 to October 31, 2006. GTI's activities during the report quarter were limited to administrative work. The work at the University of Arkansas continued in line with the initial scope of work and the identified questions regarding surface to cloud heat transfer as being largely responsible for the instability problems previously encountered. A brief summary of results is discussed in this section and the complete report from University of Arkansas is provided. All work planned for this project has been completed. Specifically: Task A--Simulation of Low-Wind-Speed Stable Atmospheric Conditions: This task has been completed, and a new version of FEM3A will be received by GTI. Task B--Verification for Dispersion over Rough Surfaces With and Without Obstacles: This task has been completed, and a new version of FEM3A will be received by GTI. Task C--Adapting the FEM3A Model for More General Application This task was obviated when DOE redirected the contract near the project midpoint. Task D--Provide assistance and wind tunnel data to DOE for FLUENT development This task has been completed and data requested by DOE-NETL has been delivered. Researchers at the University of Arkansas are preparing the final report that will be received by GTI by November 30, 2006.

  11. The long-term climate change task of the Hanford permanent isolation barrier development program

    SciTech Connect

    Not Available

    1994-08-01

    The Hanford Site Permanent Isolation Barrier Development Program is developing an in-place disposal capability for low-level nuclear waste for the US Department of Energy at the Hanford Site in southeastern Washington State. Layered earthen and engineered barriers are being developed that will function in what is currently a semiarid environment (mean annual precipitation and temperature of 16 cm and 11.8{degrees}C, respectively) for at least 1,000 yr by limiting the infiltration of water through the waste. The Long-Term Climate Change Task has specific goals of (1) obtaining defensible probabilistic projections of the long-term climate variability in the Hanford Site region at many different time scales into the future; (2) developing several test-case climate scenarios that bracket the range of potential future climate, including both greenhouse warming and cycling into another ice age; and (3) using the climate scenarios both to test and to model protective barrier performance. Results from the Carp Lake Pollen Coring Project indicate that for the last approximately 100,000 yr the Columbia River Basin`s long-term range of mean annual precipitation ranged from 25%--50% below to 28% above modern levels, while temperature has ranged from 7{degrees}C--10{degrees}C below to 2{degrees}C above modern levels. This long record provides confidence that such a range should bracket potential natural climate change even if the earth cycles back into another Ice Age in the next few millennia.

  12. Ares I-X Flight Evaluation Tasks in Support of Ares I Development

    NASA Technical Reports Server (NTRS)

    Huebner, Lawrence D.; Richards, James S.; Coates, Ralph H., III; Cruit, Wendy D.; Ramsey, Matthew N.

    2010-01-01

    NASA s Constellation Program successfully launched the Ares I-X Flight Test Vehicle on October 28, 2009. The Ares I-X flight was a development flight test that offered a unique opportunity for early engineering data to impact the design and development of the Ares I crew launch vehicle. As the primary customer for flight data from the Ares I-X mission, the Ares Projects Office established a set of 33 flight evaluation tasks to correlate fight results with prospective design assumptions and models. Included within these tasks were direct comparisons of flight data with pre-flight predictions and post-flight assessments utilizing models and modeling techniques being applied to design and develop Ares I. A discussion of the similarities and differences in those comparisons and the need for discipline-level model updates based upon those comparisons form the substance of this paper. The benefits of development flight testing were made evident by implementing these tasks that used Ares I-X data to partially validate tools and methodologies in technical disciplines that will ultimately influence the design and development of Ares I and future launch vehicles. The areas in which partial validation from the flight test was most significant included flight control system algorithms to predict liftoff clearance, ascent, and stage separation; structural models from rollout to separation; thermal models that have been updated based on these data; pyroshock attenuation; and the ability to predict complex flow fields during time-varying conditions including plume interactions.

  13. The influence of autostereoscopic 3D displays on subsequent task performance

    NASA Astrophysics Data System (ADS)

    Barkowsky, Marcus; Le Callet, Patrick

    2010-02-01

    Viewing 3D content on an autostereoscopic is an exciting experience. This is partly due to the fact that the 3D effect is seen without glasses. Nevertheless, it is an unnatural condition for the eyes as the depth effect is created by the disparity of the left and the right view on a flat screen instead of having a real object at the corresponding location. Thus, it may be more tiring to watch 3D than 2D. This question is investigated in this contribution by a subjective experiment. A search task experiment is conducted and the behavior of the participants is recorded with an eyetracker. Several indicators both for low level perception as well as for the task performance itself are evaluated. In addition two optometric tests are performed. A verification session with conventional 2D viewing is included. The results are discussed in detail and it can be concluded that the 3D viewing does not have a negative impact on the task performance used in the experiment.

  14. Factors Considered by Elementary Teachers When Developing and Modifying Mathematical Tasks to Support Children's Mathematical Thinking

    NASA Astrophysics Data System (ADS)

    Fredenberg, Michael Duane

    The idea that problems and tasks play a pivotal role in a mathematics lesson has a long standing in mathematics education research. Recent calls for teaching reform appeal for training teachers to better understand how students learn mathematics and to employ students' mathematical thinking as the basis for pedagogy (CCSSM, 2010; NCTM, 2000; NRC 1999). The teaching practices of (a) developing a task for a mathematics lesson and, (b) modifying the task for students while enacting the lesson fit within the scope of supporting students' mathematical thinking. Surprisingly, an extensive search of the literature did not yield any research aimed to identify and refine the constituent parts of the aforementioned teaching practices in the manner called for by Grossman and xiii colleagues (2009). Consequently, my research addresses the two questions: (a) what factors do exemplary elementary teachers consider when developing a task for a mathematics lesson? (b) what factors do they consider when they modify a task for a student when enacting a lesson? I conducted a multiple case study involving three elementary teachers, each with extensive training in the area of Cognitively Guided Instruction (CGI), as well as several years experience teaching mathematics following the principles of CGI (Carpenter et al., 1999). I recorded video of three mathematics lessons with each participant and after each lesson I conducted a semi-structured stimulated recall interview. A subsequent follow-up clinical interview was conducted soon thereafter to further explore the teacher's thoughts (Ginsberg, 1997). In addition, my methodology included interjecting myself at select times during a lesson to ask the teacher to explain her reasoning. Qualitative analysis led to a framework that identified four categories of influencing factors and seven categories of supporting objectives for the development of a task. Subsets of these factors and objectives emerged as particularly relevant when the

  15. Final report for confinement vessel analysis. Task 3, Analysis of confinement vessel doors

    SciTech Connect

    Lewis, B.B.

    1993-12-31

    The confinement vessel has five closure doors of two different sizes. The vessel must withstand an initial dynamic load and a quasi-static internal pressure with no leakage of gases through the port seals. Task 3 of the Confinement Vessel Analysis Program was to assess the doors for safety. Of primary concern is the integrity of the seal. This encompasses the structural integrity of the door and nozzle as separate structural elements and the relative motion between the door and nozzle which could cause leakage of gases around the seals. In addition, the authors would like to obtain a better understanding of the effect of the bolt preload, especially as it affects the dynamic response of the structure. The authors explain the objectives of the task in Section 1, describe the models used for the analyses in Section 2, and give results in Section 3. They list conclusions and recommendations in Section 4.

  16. Personal and task-related moderators of leader-member exchange among software developers.

    PubMed

    Ozer, Muammer

    2008-09-01

    Although earlier studies have shown significant positive relationships between leader-member exchange (LMX) and its outcomes, they have also noted that the effect sizes of these relationships have been modest and heterogeneous. Addressing numerous calls for future studies that examine potential moderators of the LMX-job performance and LMX-job satisfaction relationships and utilizing a multidomain perspective, this study tests the moderating roles of personal (i.e., locus of control) and task-related (i.e., task autonomy) factors on these relationships. The results of an empirical study with a sample of 287 software developers and 164 supervisors participating at a large international information technology exhibition indicated that the LMX-job performance relationship was stronger when employees' locus of control was internal as opposed to when it was external. In addition, it was stronger when task autonomy was high as opposed to when it was low. Moreover, the results suggested that the LMX-job satisfaction relationship was stronger when task autonomy was high as opposed to when it was low. Finally, contrary to theoretical expectations, employees' locus of control did not moderate the LMX-job satisfaction relationship.

  17. Hawaii Energy Strategy Project 2: Fossil Energy Review. Task IV. Scenario development and analysis

    SciTech Connect

    Yamaguchi, N.D.; Breazeale, K.

    1993-12-01

    The Hawaii Energy Strategy (HES) Program is a seven-project effort led by the State of Hawaii Department of Business, Economic Development & Tourism (DBEDT) to investigate a wide spectrum of Hawaii energy issues. The East-West Center`s Program on Resources: Energy and Minerals, has been assigned HES Project 2, Fossil Energy Review, which focuses on fossil energy use in Hawaii and the greater regional and global markets. HES Project 2 has four parts: Task I (World and Regional Fossil Energy Dynamics) covers petroleum, natural gas, and coal in global and regional contexts, along with a discussion of energy and the environment. Task II (Fossil Energy in Hawaii) focuses more closely on fossil energy use in Hawaii: current utilization and trends, the structure of imports, possible future sources of supply, fuel substitutability, and energy security. Task III`s emphasis is Greenfield Options; that is, fossil energy sources not yet used in Hawaii. This task is divided into two sections: first, an in-depth {open_quotes}Assessment of Coal Technology Options and Implications for the State of Hawaii,{close_quotes} along with a spreadsheet analysis model, which was subcontracted to the Environmental Assessment and Information Sciences Division of Argonne National Laboratory; and second, a chapter on liquefied natural gas (LNG) in the Asia-Pacific market and the issues surrounding possible introduction of LNG into the Hawaii market.

  18. Personal and task-related moderators of leader-member exchange among software developers.

    PubMed

    Ozer, Muammer

    2008-09-01

    Although earlier studies have shown significant positive relationships between leader-member exchange (LMX) and its outcomes, they have also noted that the effect sizes of these relationships have been modest and heterogeneous. Addressing numerous calls for future studies that examine potential moderators of the LMX-job performance and LMX-job satisfaction relationships and utilizing a multidomain perspective, this study tests the moderating roles of personal (i.e., locus of control) and task-related (i.e., task autonomy) factors on these relationships. The results of an empirical study with a sample of 287 software developers and 164 supervisors participating at a large international information technology exhibition indicated that the LMX-job performance relationship was stronger when employees' locus of control was internal as opposed to when it was external. In addition, it was stronger when task autonomy was high as opposed to when it was low. Moreover, the results suggested that the LMX-job satisfaction relationship was stronger when task autonomy was high as opposed to when it was low. Finally, contrary to theoretical expectations, employees' locus of control did not moderate the LMX-job satisfaction relationship. PMID:18808235

  19. Advanced Turbine Systems Program conceptual design and product development: Task 4.0

    SciTech Connect

    Not Available

    1994-06-01

    This Topical Report presents the results of Task 4 of the Westinghouse ATS Program. The purpose of Task 4 is to determine the technical development needs for conversion of the gas-fired ATS (GFATS). Two closely related, advanced, coal-based power plant technologies have been selected for consideration as the CFATS -- air-blown, coal gasification with hot gas cleaning incorporated into an Integrated Gasification Combined Cycle (IGCC), and the Second-Generation Pressurized Fluidized Bed Combustion (PFBC) combined cycle. These are described and their estimated performance and emissions in the CFATS are reported. A development program for the CFATS is described that focuses on major commercialization issues. These issues are in the areas of combustion, flow distribution, structural analysis, and materials selection.

  20. High temperature static strain gage development contract, tasks 1 and 2

    NASA Technical Reports Server (NTRS)

    Hulse, C. O.; Bailey, R. S.; Grant, H. P.; Przybyszewski, J. S.

    1987-01-01

    Results are presented for the first two tasks to develop resistive strain gage systems for use up to 1250 K on blades and vanes in gas turbine engines under tests. The objective of these two tasks was to further improve and evaluate two static strain gage alloys identified as candidates in a previous program. Improved compositions were not found for either alloy. Further efforts on the Fe-11.9Al-10.6Cr weigth percent alloy were discontinued because of time dependent drift problems at 1250 K in air. When produced as a 6.5 micrometer thick sputtered film, the Pd-13Cr weight percent alloys is not sufficiently stable for this use in air at 1250 K and a protective overcoat system will need to be developed.

  1. High temperature static strain gage development contract, tasks 1 and 2

    NASA Astrophysics Data System (ADS)

    Hulse, C. O.; Bailey, R. S.; Grant, H. P.; Przybyszewski, J. S.

    1987-07-01

    Results are presented for the first two tasks to develop resistive strain gage systems for use up to 1250 K on blades and vanes in gas turbine engines under tests. The objective of these two tasks was to further improve and evaluate two static strain gage alloys identified as candidates in a previous program. Improved compositions were not found for either alloy. Further efforts on the Fe-11.9Al-10.6Cr weigth percent alloy were discontinued because of time dependent drift problems at 1250 K in air. When produced as a 6.5 micrometer thick sputtered film, the Pd-13Cr weight percent alloys is not sufficiently stable for this use in air at 1250 K and a protective overcoat system will need to be developed.

  2. Coal-fueled high-speed diesel engine development: Task 2, Market assessment and economic analysis

    SciTech Connect

    Not Available

    1991-12-01

    Based on the preliminary coal engine design developed, this task was conducted to identify the best opportunity(s) to enter the market with the future coal-fueled, high-speed diesel engine. The results of this market and economic feasibility assessment will be used to determine what specific heavy duty engine application(s) are most attractive for coal fuel, and also define basic economic targets for the engine to be competitive.

  3. 3 CFR 13632 - Executive Order 13632 of December 7, 2012. Establishing the Hurricane Sandy Rebuilding Task Force

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... Urban Development (Chair). (a) In addition to the Chair, the Task Force shall consist of the head of... Agriculture; (iv) the Department of Commerce; (v) the Department of Labor; (vi) the Department of Health and... Department of Housing and Urban Development shall provide the Task Force with such administrative...

  4. Changes in default mode network as automaticity develops in a categorization task.

    PubMed

    Shamloo, Farzin; Helie, Sebastien

    2016-10-15

    The default mode network (DMN) is a set of brain regions in which blood oxygen level dependent signal is suppressed during attentional focus on the external environment. Because automatic task processing requires less attention, development of automaticity in a rule-based categorization task may result in less deactivation and altered functional connectivity of the DMN when compared to the initial learning stage. We tested this hypothesis by re-analyzing functional magnetic resonance imaging data of participants trained in rule-based categorization for over 10,000 trials (Helie et al., 2010) [12,13]. The results show that some DMN regions are deactivated in initial training but not after automaticity has developed. There is also a significant decrease in DMN deactivation after extensive practice. Seed-based functional connectivity analyses with the precuneus, medial prefrontal cortex (two important DMN regions) and Brodmann area 6 (an important region in automatic categorization) were also performed. The results show increased functional connectivity with both DMN and non-DMN regions after the development of automaticity, and a decrease in functional connectivity between the medial prefrontal cortex and ventromedial orbitofrontal cortex. Together, these results further support the hypothesis of a strategy shift in automatic categorization and bridge the cognitive and neuroscientific conceptions of automaticity in showing that the reduced need for cognitive resources in automatic processing is accompanied by a disinhibition of the DMN and stronger functional connectivity between DMN and task-related brain regions. PMID:27457134

  5. High-pressure coal fuel processor development. Task 1, Proof of principle testing

    SciTech Connect

    Greenhalgh, M.L.

    1992-11-01

    The objective of Subtask 1.1 Engine Feasibility was to conduct research needed to establish the technical feasibility of ignition and stable combustion of directly injected, 3,000 psi, low-Btu gas with glow plug ignition assist at diesel engine compression ratios. This objective was accomplished by designing, fabricating, testing and analyzing the combustion performance of synthesized low-Btu coal gas in a single-cylinder test engine combustion rig located at the Caterpillar Technical Center engine lab in Mossville, Illinois. The objective of Subtask 1.2 Fuel Processor Feasibility was to conduct research needed to establish the technical feasibility of air-blown, fixed-bed, high-pressure coal fuel processing at up to 3,000 psi operating pressure, incorporating in-bed sulfur and particulate capture. This objective was accomplished by designing, fabricating, testing and analyzing the performance of bench-scale processors located at Coal Technology Corporation (subcontractor) facilities in Bristol, Virginia. These two subtasks were carried out at widely separated locations and will be discussed in separate sections of this report. They were, however, independent in that the composition of the synthetic coal gas used to fuel the combustion rig was adjusted to reflect the range of exit gas compositions being produced on the fuel processor rig. Two major conclusions resulted from this task. First, direct injected, ignition assisted Diesel cycle engine combustion systems can be suitably modified to efficiently utilize these low-Btu gas fuels. Second, high pressure gasification of selected run-of-the-mine coals in batch-loaded fuel processors is feasible. These two findings, taken together, significantly reduce the perceived technical risks associated with the further development of the proposed coal gas fueled Diesel cycle power plant concept.

  6. Lithium-vanadium advanced blanket development. ITER final report on U.S. contribution: Task T219/T220

    SciTech Connect

    Smith, D.L.; Mattas, R.F.

    1997-07-01

    The objective of this task is to develop the required data base and demonstrate the performance of a liquid lithium-vanadium advanced blanket design. The task has two main activities related to vanadium structural material and liquid lithium system developments. The vanadium alloy development activity included four subtasks: (1.1) baseline mechanical properties of non irradiated base metal and weld metal joints; (1.2) compatibility with liquid lithium; (1.3) material irradiation tests; and (1.4) development of material manufacturing and joining methods. The lithium blanket technology activity included four subtasks: (2.1) electrical insulation development and testing for liquid metal systems; (2.2) MHD pressure drop and heat transfer study for self-cooled liquid metal systems; (2.3) chemistry of liquid lithium; and (2.4) design, fabrication and testing of ITER relevant size blanket mockups. A summary of the progress and results obtained during the period 1995 and 1996 in each of the subtask areas is presented in this report.

  7. Development and initial validation of an endoscopic part-task training box

    PubMed Central

    Thompson, Christopher C.; Jirapinyo, Pichamol; Kumar, Nitin; Ou, Amy; Camacho, Andrew; Lengyel, Balazs; Ryan, Michele B.

    2016-01-01

    Background and study aims There is currently no objective and validated methodology available to assess the progress of endoscopy trainees or to determine when technical competence has been achieved. The aims of the current study were to develop an endoscopic part-task simulator and to assess scoring system validity. Methods Fundamental endoscopic skills were determined via kinematic analysis, literature review, and expert interviews. Simulator prototypes and scoring systems were developed to reflect these skills. Validity evidence for content, internal structure, and response process was evaluated. Results The final training box consisted of five modules (knob control, torque, retroflexion, polypectomy, and navigation and loop reduction). A total of 5 minutes were permitted per module with extra points for early completion. Content validity index (CVI)-realism was 0.88, CVI-relevance was 1.00, and CVI-representativeness was 0.88, giving a composite CVI of 0.92. Overall, 82% of participants considered the simulator to be capable of differentiating between ability levels, and 93% thought the simulator should be used to assess ability prior to performing procedures in patients. Inter-item assessment revealed correlations from 0.67 to 0.93, suggesting that tasks were sufficiently correlated to assess the same underlying construct, with each task remaining independent. Each module represented 16.0%–26.1% of the total score, suggesting that no module contributed disproportionately to the composite score. Average box scores were 272.6 and 284.4 (P=0.94) when performed sequentially, and average score for all participants with proctor 1 was 297.6 and 308.1 with proctor 2 (P=0.94), suggesting reproducibility and minimal error associated with test administration. Conclusion A part-task training box and scoring system were developed to assess fundamental endoscopic skills, and validity evidence regarding content, internal structure, and response process was demonstrated

  8. Utilization Assessment of Target Electrification Vehicles at Marine Corps Base Camp Lejeune. Task 3

    SciTech Connect

    Schey, Stephen; Francfort, Jim

    2015-11-01

    Battelle Energy Alliance, LLC, managing and operating contractor for the U.S. Department of Energy’s Idaho National Laboratory, is the lead laboratory for U.S. Department of Energy Advanced Vehicle Testing. Battelle Energy Alliance, LLC contracted with Intertek Testing Services, North America (Intertek) to conduct several U.S. Department of Defense base studies to identify potential U.S. Department of Defense transportation systems that are strong candidates for introduction or expansion of plug-in electric vehicles (PEVs). Task 1 consisted of a survey of the non-tactical fleet of vehicles at MCBCL to begin the review of vehicle mission assignments and types of vehicles in service. Task 2 involved identifying daily operational characteristics of select vehicles and initiating data logging of vehicle movements in order to characterize the vehicle’s mission. Individual observations of these selected vehicles provide the basis for recommendations related to PEV adoption and whether a battery electric vehicle or plug-in hybrid electric vehicle (collectively referred to as PEVs) can fulfill the mission requirements and provide observations related to placement of PEV charging infrastructure. This report provides the results of the data analysis and observations related to replacement of current vehicles with PEVs. This fulfills part of the Task 3 requirements. Task 3 also includes an assessment of the charging infrastructure required to support this replacement, which is the subject of a separate report. Intertek acknowledges the support of Idaho National Laboratory, Marine Corps headquarters, and Marine Corps Base Camp Lejeune Fleet management and personnel for participation in this study. Intertek is pleased to provide this report and is encouraged by enthusiasm and support from MCBCL personnel.

  9. School District Cabinet Member Task and Relationship Conflict Behavior during Budget Development in a State Fiscal Crisis

    ERIC Educational Resources Information Center

    Nickerson, John

    2009-01-01

    Purpose. The first purpose of this study was to determine to what extent task and relationship conflict occurred in school district cabinets during budget development in a state budget crisis. The second purpose was to determine which cabinet member task and relationship conflict behaviors were demonstrated during budget development in a state…

  10. 77 FR 76000 - Notice of Availability of Draft Report of the NOAA Research and Development Portfolio Review Task...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-26

    ... Availability of Draft Report of the NOAA Research and Development Portfolio Review Task Force and Request for... draft report of the SAB Research and Development Portfolio Review Task Force (PRTF) for public comment.../ SAB, Silver Spring, Maryland 20910. FOR FURTHER INFORMATION CONTACT: Dr. Cynthia Decker,...

  11. The pungent substances piperine, capsaicin, 6-gingerol and polygodial inhibit the human two-pore domain potassium channels TASK-1, TASK-3 and TRESK

    PubMed Central

    Beltrán, Leopoldo R.; Dawid, Corinna; Beltrán, Madeline; Gisselmann, Guenter; Degenhardt, Katharina; Mathie, Klaus; Hofmann, Thomas; Hatt, Hanns

    2013-01-01

    For a long time, the focus of trigeminal chemoperception has rested almost exclusively on TRP channels. However, two-pore domain (K2P) potassium channels have recently been identified as targets for substances associated with typical trigeminal sensations, such as numbing and tingling. In addition, they have been shown to be modulated by several TRP agonists. We investigated whether the pungent substances piperine, capsaicin, 6-gingerol and polygodial have an effect on human K2P channels. For this purpose, we evaluated the effects of these pungent substances on both wild-type and mutant K2P channels by means of two-electrode voltage-clamp experiments using Xenopus laevis oocytes. All four pungent substances were found to inhibit the basal activity of TASK-1 (K2P 3.1), TASK-3 (K2P 9.1), and TRESK (K2P 18.1) channels. This inhibitory effect was dose-dependent and, with the exception of polygodial on TASK-1, fully reversible. However, only piperine exhibited an IC50 similar to its reported EC50 on TRP channels. Finally, we observed for TASK-3 that mutating H98 to E markedly decreased the inhibition induced by piperine, capsaicin, and 6-gingerol, but not by polygodial. Our data contribute to the relatively sparse knowledge concerning the pharmacology of K2P channels and also raise the question of whether K2P channels could be involved in the pungency perception of piperine. PMID:24302912

  12. Developing Bayesian adaptive methods for estimating sensitivity thresholds (d′) in Yes-No and forced-choice tasks

    PubMed Central

    Lesmes, Luis A.; Lu, Zhong-Lin; Baek, Jongsoo; Tran, Nina; Dosher, Barbara A.; Albright, Thomas D.

    2015-01-01

    Motivated by Signal Detection Theory (SDT), we developed a family of novel adaptive methods that estimate the sensitivity threshold—the signal intensity corresponding to a pre-defined sensitivity level (d′ = 1)—in Yes-No (YN) and Forced-Choice (FC) detection tasks. Rather than focus stimulus sampling to estimate a single level of %Yes or %Correct, the current methods sample psychometric functions more broadly, to concurrently estimate sensitivity and decision factors, and thereby estimate thresholds that are independent of decision confounds. Developed for four tasks—(1) simple YN detection, (2) cued YN detection, which cues the observer's response state before each trial, (3) rated YN detection, which incorporates a Not Sure response, and (4) FC detection—the qYN and qFC methods yield sensitivity thresholds that are independent of the task's decision structure (YN or FC) and/or the observer's subjective response state. Results from simulation and psychophysics suggest that 25 trials (and sometimes less) are sufficient to estimate YN thresholds with reasonable precision (s.d. = 0.10–0.15 decimal log units), but more trials are needed for FC thresholds. When the same subjects were tested across tasks of simple, cued, rated, and FC detection, adaptive threshold estimates exhibited excellent agreement with the method of constant stimuli (MCS), and with each other. These YN adaptive methods deliver criterion-free thresholds that have previously been exclusive to FC methods. PMID:26300798

  13. Modeling automatic threat detection: development of a face-in-the-crowd task.

    PubMed

    Schmidt-Daffy, Martin

    2011-02-01

    An angry face is expected to be detected faster than a happy face because of an early, stimulus-driven analysis of threat-related properties. However, it is unclear to what extent results from the visual search approach-the face-in-the-crowd task-mirror this automatic analysis. The paper outlines a model of automatic threat detection that combines the assumption of a neuronal system for threat detection with contemporary theories of visual search. The model served as a guideline for the development of a new face-in-the-crowd task. The development involved three preliminary studies that provided a basis for the selection of angry and happy facial stimuli resembling each other in respect to perceptibility, homogeneity, and intensity. With these stimuli a signal detection version of the search task was designed and tested. For crowds composed of neutral faces, the sensitivity measure d' proved the expected detection advantage of angry faces compared to happy faces. However, the emotional expression made no difference if a neutral face had to be detected in crowd composed of either angry or happy faces. Results are in line with the assumption of a stimulus-driven shift of attention giving rise to the superior detection of angry target faces.

  14. Development of an Objective Space Suit Mobility Performance Metric Using Metabolic Cost and Functional Tasks

    NASA Technical Reports Server (NTRS)

    McFarland, Shane M.; Norcross, Jason

    2016-01-01

    Existing methods for evaluating EVA suit performance and mobility have historically concentrated on isolated joint range of motion and torque. However, these techniques do little to evaluate how well a suited crewmember can actually perform during an EVA. An alternative method of characterizing suited mobility through measurement of metabolic cost to the wearer has been evaluated at Johnson Space Center over the past several years. The most recent study involved six test subjects completing multiple trials of various functional tasks in each of three different space suits; the results indicated it was often possible to discern between different suit designs on the basis of metabolic cost alone. However, other variables may have an effect on real-world suited performance; namely, completion time of the task, the gravity field in which the task is completed, etc. While previous results have analyzed completion time, metabolic cost, and metabolic cost normalized to system mass individually, it is desirable to develop a single metric comprising these (and potentially other) performance metrics. This paper outlines the background upon which this single-score metric is determined to be feasible, and initial efforts to develop such a metric. Forward work includes variable coefficient determination and verification of the metric through repeated testing.

  15. Toward the Development of Cognitive Task Difficulty Metrics to Support Intelligence Analysis Research

    SciTech Connect

    Greitzer, Frank L.

    2005-08-08

    Intelligence analysis is a cognitively complex task that is the subject of considerable research aimed at developing methods and tools to aid the analysis process. To support such research, it is necessary to characterize the difficulty or complexity of intelligence analysis tasks in order to facilitate assessments of the impact or effectiveness of tools that are being considered for deployment. A number of informal accounts of ''What makes intelligence analysis hard'' are available, but there has been no attempt to establish a more rigorous characterization with well-defined difficulty factors or dimensions. This paper takes an initial step in this direction by describing a set of proposed difficulty metrics based on cognitive principles.

  16. Professional development in statistics, technology, and cognitively demanding tasks: classroom implementation and obstacles

    NASA Astrophysics Data System (ADS)

    Foley, Gregory D.; Bakr Khoshaim, Heba; Alsaeed, Maha; Nihan Er, S.

    2012-03-01

    Attending professional development programmes can support teachers in applying new strategies for teaching mathematics and statistics. This study investigated (a) the extent to which the participants in a professional development programme subsequently used the techniques they had learned when teaching mathematics and statistics and (b) the obstacles they encountered in enacting cognitively demanding instructional tasks in their classrooms. The programme created an intellectual learning community among the participants and helped them gain confidence as teachers of statistics, and the students of participating teachers became actively engaged in deep mathematical thinking. The participants indicated, however, that time, availability of resources and students' prior achievement critically affected the implementation of cognitively demanding instructional activities.

  17. Study of advanced composite structural design concepts for an arrow wing supersonic cruise configuration, task 3

    NASA Technical Reports Server (NTRS)

    1978-01-01

    A structural design study was conducted to assess the relative merits of structural concepts using advanced composite materials for an advanced supersonic aircraft cruising at Mach 2.7. The configuration and structural arrangement developed during Task I and II of the study, was used as the baseline configuration. Allowable stresses and strains were established for boron and advanced graphite fibers based on projected fiber properties available in the next decade. Structural concepts were designed and analyzed using graphite polyimide and boron polyimide, applied to stiffened panels and conventional sandwich panels. The conventional sandwich panels were selected as the structural concept to be used on the wing structure. The upper and lower surface panels of the Task I arrow wing were redesigned using high-strength graphite polyimide sandwich panels over the titanium spars and ribs. The ATLAS computer system was used as the basis for stress analysis and resizing the surface panels using the loads from the Task II study, without adjustment for change in aeroelastic deformation. The flutter analysis indicated a decrease in the flutter speed compared to the baseline titanium wing design. The flutter analysis indicated a decrease in the flutter speed compared to the baseline titanium wing design. The flutter speed was increased to that of the titanium wing, with a weight penalty less than that of the metallic airplane.

  18. Vision-Based Long-Range 3D Tracking, applied to Underground Surveying Tasks

    NASA Astrophysics Data System (ADS)

    Mossel, Annette; Gerstweiler, Georg; Vonach, Emanuel; Kaufmann, Hannes; Chmelina, Klaus

    2014-04-01

    To address the need of highly automated positioning systems in underground construction, we present a long-range 3D tracking system based on infrared optical markers. It provides continuous 3D position estimation of static or kinematic targets with low latency over a tracking volume of 12 m x 8 m x 70 m (width x height x depth). Over the entire volume, relative 3D point accuracy with a maximal deviation ≤ 22 mm is ensured with possible target rotations of yaw, pitch = 0 - 45° and roll = 0 - 360°. No preliminary sighting of target(s) is necessary since the system automatically locks onto a target without user intervention and autonomously starts tracking as soon as a target is within the view of the system. The proposed system needs a minimal hardware setup, consisting of two machine vision cameras and a standard workstation for data processing. This allows for quick installation with minimal disturbance of construction work. The data processing pipeline ensures camera calibration and tracking during on-going underground activities. Tests in real underground scenarios prove the system's capabilities to act as 3D position measurement platform for multiple underground tasks that require long range, low latency and high accuracy. Those tasks include simultaneously tracking of personnel, machines or robots.

  19. Summary report for subcontract No. 0412J0004-3Y, task order 23. Final report

    SciTech Connect

    1997-10-02

    This task covers work performed by Carlton S. Young for various projects in Group P-22, Los Alamos National Lab from September 1996 to September 22, 1997. Projects worked on and charged to contract: (1) rebound, 80%; (2) reports on Nevada events Divider and Victoria, 10%; (3) FORTRAN modifications to a Macintosh version of the ACCEPT code and calculations on GAAs PCDs and Cherenkov detectors, 0%; (4) design of time and space-resolved burn measurements for the National Ignition Facility (NIF) based on a gas Cherenkov gamma-ray detector and proposals for more money to do the same, 10%. A summary of work on each project is included.

  20. Offshore Code Comparison Collaboration (OC3) for IEA Wind Task 23 Offshore Wind Technology and Deployment

    SciTech Connect

    Jonkman, J.; Musial, W.

    2010-12-01

    This final report for IEA Wind Task 23, Offshore Wind Energy Technology and Deployment, is made up of two separate reports, Subtask 1: Experience with Critical Deployment Issues and Subtask 2: Offshore Code Comparison Collaborative (OC3). Subtask 1 discusses ecological issues and regulation, electrical system integration, external conditions, and key conclusions for Subtask 1. Subtask 2 included here, is the larger of the two volumes and contains five chapters that cover background information and objectives of Subtask 2 and results from each of the four phases of the project.

  1. Feasibility study of modern airships, phase 1. Volume 3: Historical overview (task 1)

    NASA Technical Reports Server (NTRS)

    Faurote, G. L.

    1975-01-01

    The history of lighter-than-air vehicles is reviewed in terms of providing a background for the mission analysis and parametric analysis tasks. Data from past airships and airship operations are presented in the following areas: (1) parameterization of design characteristics; (2) markets, missions, costs, and operating procedures, (3) indices of efficiency for comparison; (4) identification of critical design and operational characteristics; and (5) definition of the 1930 state-of-the-art and the 1974 state-of-the-art from a technical and economic standpoint.

  2. Object-oriented design for imaging-task workstations in international development

    NASA Astrophysics Data System (ADS)

    McNeill, Kevin M.; Okazaki, Nobuo; Parra, Miguel V.; Toshimitsu, Akihiro; Dallas, William J.; Shinoda, Hidenori; Evanoff, Michael G.; Ovitt, Theron W.

    1997-05-01

    At the University of Arizona, software development for image viewing tasks use object-oriented techniques for scalability, portability, cost and the ability to adapt rapidly to changing technology. Object orientation facilitates object-based decomposition, rapid development, code reuse and portability. These techniques were used developing software for a diagnostic system for the Pulmonary Section of Toshiba General Hospital, Tokyo, Japan. Object-oriented analysis and design were based on the Grady Booch method. Implemented used visual C++. Software components are implemented as cooperating objects. The resulting Toshiba-Arizona Viewing Station (TAVS) software system was installed in Tokyo in July 1996 for clinical evaluation. The host system provides 1760 X 2140, grey scale resolution. HIS/RIS integration allows HIS/RIS workstations to control the TAVS. TAVS code has been demonstrated on systems ranging from 'palm-top' computers to high-performance desktop systems. TAVS software objects were then modified and a TAVS system was installed in the University Medical Center, Tucson, Arizona supporting diagnostic image viewing tasks in the Emergency Department. This approach has demonstrated support for rapid development and adaptability to diverse end-user requirements and produced software which can operate across platforms.

  3. The development of cognitive flexibility beyond the preschool period: an investigation using a modified Flexible Item Selection Task.

    PubMed

    Dick, Anthony Steven

    2014-09-01

    We explored the development of cognitive flexibility in typically developing 6-, 8-, and 10-year-olds and adults by modifying a common cognitive flexibility task, the Flexible Item Selection Task (FIST). Although performance on the standard FIST reached ceiling by 8 years, FIST performance on other variations continued to improve until 10 years of age. Within a detailed task analysis, we also explored working memory storage and processing components of executive function and how these contribute to the development of cognitive flexibility. The findings reinforce the notion that cognitive flexibility is a multifaceted construct but that the development of working memory contributes in part to age-related change in this ability.

  4. Breathing Stimulant Compounds Inhibit TASK-3 Potassium Channel Function Likely by Binding at a Common Site in the Channel Pore

    PubMed Central

    Chokshi, Rikki H.; Larsen, Aaron T.; Bhayana, Brijesh

    2015-01-01

    Compounds PKTHPP (1-{1-[6-(biphenyl-4-ylcarbonyl)-5,6,7,8-tetrahydropyrido[4,3-d]-pyrimidin-4-yl]piperidin-4-yl}propan-1-one), A1899 (2ʹ′-[(4-methoxybenzoylamino)methyl]biphenyl-2-carboxylic acid 2,4-difluorobenzylamide), and doxapram inhibit TASK-1 (KCNK3) and TASK-3 (KCNK9) tandem pore (K2P) potassium channel function and stimulate breathing. To better understand the molecular mechanism(s) of action of these drugs, we undertook studies to identify amino acid residues in the TASK-3 protein that mediate this inhibition. Guided by homology modeling and molecular docking, we hypothesized that PKTHPP and A1899 bind in the TASK-3 intracellular pore. To test our hypothesis, we mutated each residue in or near the predicted PKTHPP and A1899 binding site (residues 118–128 and 228–248), individually, to a negatively charged aspartate. We quantified each mutation's effect on TASK-3 potassium channel concentration response to PKTHPP. Studies were conducted on TASK-3 transiently expressed in Fischer rat thyroid epithelial monolayers; channel function was measured in an Ussing chamber. TASK-3 pore mutations at residues 122 (L122D, E, or K) and 236 (G236D) caused the IC50 of PKTHPP to increase more than 1000-fold. TASK-3 mutants L122D, G236D, L239D, and V242D were resistant to block by PKTHPP, A1899, and doxapram. Our data are consistent with a model in which breathing stimulant compounds PKTHPP, A1899, and doxapram inhibit TASK-3 function by binding at a common site within the channel intracellular pore region, although binding outside the channel pore cannot yet be excluded. PMID:26268529

  5. ADVANCED OXYFUEL BOILERS AND PROCESS HEATERS FOR COST EFFECTIVE CO{sub 2} CAPTURE AND SEQUESTRATION

    SciTech Connect

    David R. Thompson; Lawrence E. Bool; G. Maxwell Christie

    2003-07-01

    This annual technical progress report summarizes the work accomplished during the first year of the program, January-December 2002, in the following task areas: Task 1--Conceptual Design, Task 2--Laboratory Scale Evaluations, Task 3--OTM Development, Task 4--Economic Evaluation and Commercialization Planning and Task 5--Program Management. The program has experienced significant delays due to several factors. The budget has also been significantly under spent. Based on recent technical successes significant future progress is expected. A number of concepts for integrating Oxygen Transport Membranes (OTMs) into boilers and process heaters to facilitate oxy-fuel combustion have been proposed. A detailed modeling plan has been proposed and early modeling work has focused on developing spreadsheet based models for quick engineering calculations. Combustion reactor laboratory scale evaluations efforts have been delayed due to the closing of Praxair's Tarrytown facility in December 2001. Experimental facilities and personnel have been relocated to Praxair's facility in Tonawanda. The facilities have recently been re-commissioned. Work with the OTM development task has also been delayed as early material selections were discarded. More recently, more promising OTM material compositions have been identified. Economic evaluation commenced. Information was acquired that quantified the attractiveness of the advanced oxygen-fired boiler. CO{sub 2} capture and compression are still estimated to be much less than $10/ton carbon.

  6. Bridging the Gap: Individual Growth and Development Indicators--The Which One Doesn't Belong Task

    ERIC Educational Resources Information Center

    Rodriguez, Megan I.; Wackerle-Hollman, Alisha K.

    2015-01-01

    The Individual Growth and Development Indicator (IGDI): Which One Doesn't Belong (WODB) task is an early comprehension screening assessment designed for use in pre-Kindergarten multi-tiered systems of support. This article summarizes the purpose, procedures, and evidence base currently available in the literature to support the WODB task.…

  7. Development of Vestibular Stochastic Resonance as a Sensorimotor Countermeasure: Improving Otolith Ocular and Motor Task Responses

    NASA Technical Reports Server (NTRS)

    Mulavara, Ajitkumar; Fiedler, Matthew; DeDios,Yiri E.; Galvan, Raquel; Bloomberg, Jacob; Wood, Scott

    2011-01-01

    Astronauts experience disturbances in sensorimotor function after spaceflight during the initial introduction to a gravitational environment, especially after long-duration missions. Stochastic resonance (SR) is a mechanism by which noise can assist and enhance the response of neural systems to relevant, imperceptible sensory signals. We have previously shown that imperceptible electrical stimulation of the vestibular system enhances balance performance while standing on an unstable surface. The goal of our present study is to develop a countermeasure based on vestibular SR that could improve central interpretation of vestibular input and improve motor task responses to mitigate associated risks.

  8. Task 4 supporting technology. Part 1: Detailed test plan for leading edge tile development. Leading edge material development and testing

    NASA Astrophysics Data System (ADS)

    Hogenson, P. A.; Staszak, Paul; Hinkle, Karrie

    1995-05-01

    This task develops two alternative candidate tile materials for leading edge applications: coated alumina enhanced thermal barrier (AETB) tile and silicone impregnated reusable ceramic ablator (SIRCA) tile. Upon reentry of the X-33/RLV space vehicle, the leading edges experience the highest heating rates and temperatures. The wing leading edge and nose cap experience peak temperatures in the range 2000 to 2700 F. Replacing reinforced carbon-carbon (RCC) with tile-based thermal protection system (TPS) materials is the primary objective. Weight, complexity, coating impact damage, and repairability are among the problems that this tile technology development addresses. The following subtasks will be performed in this development effort: tile coating development; SIRCA tile development; robustness testing of tiles; tile repair development; tile operations/processing; tile leading edge configuration; and life cycle testing.

  9. Task 4 supporting technology. Part 1: Detailed test plan for leading edge tile development. Leading edge material development and testing

    NASA Technical Reports Server (NTRS)

    Hogenson, P. A.; Staszak, Paul; Hinkle, Karrie

    1995-01-01

    This task develops two alternative candidate tile materials for leading edge applications: coated alumina enhanced thermal barrier (AETB) tile and silicone impregnated reusable ceramic ablator (SIRCA) tile. Upon reentry of the X-33/RLV space vehicle, the leading edges experience the highest heating rates and temperatures. The wing leading edge and nose cap experience peak temperatures in the range 2000 to 2700 F. Replacing reinforced carbon-carbon (RCC) with tile-based thermal protection system (TPS) materials is the primary objective. Weight, complexity, coating impact damage, and repairability are among the problems that this tile technology development addresses. The following subtasks will be performed in this development effort: tile coating development; SIRCA tile development; robustness testing of tiles; tile repair development; tile operations/processing; tile leading edge configuration; and life cycle testing.

  10. Task 10 -- Technology development integration. Semi-annual report, April 1--September 30, 1997

    SciTech Connect

    Erickson, T.A.; Daly, D.J.; Jones, M.L.

    1997-12-31

    Task 10 activities by the Energy and Environmental Research Center (EERC) have focused on the identification and integration of new cleanup technologies for use in the US Department of Energy (DOE) Environmental Management Program to address environmental issues within the nuclear defense complex. Under Subtask 10A, activities focused on a review of technology needs compiled by the Site Technology Coordination Groups as part of an ongoing assessment of the relevance of the EM Cooperative Agreement Program activities to EM site needs. Work under this subtask was completed August 31. Work under Task 10B had as its goal assisting in the definition and development of specific models to demonstrate several approaches to be used by DOE to encourage the commercialization of environmental technologies. This activity included identification and analysis of economic and regulatory factors affecting feasibility of commercial development of two specific projects and two general models to serve as a mechanism for the transfer of federally supported or developed environmental technologies to the private sector or for rapid utilization in the federal government`s efforts to clean up the weapons complex.

  11. Development of flight experiment task requirements. Volume 2: Technical Report. Part 1: Program report and Appendices A-G

    NASA Technical Reports Server (NTRS)

    Hatterick, G. R.

    1972-01-01

    Activities are documented of the study to determine skills required of on-orbit crew personnel of the space shuttle. The material is presented in four sections that include: (1) methodology for identifying flight experiment task-skill requirements, (2) task-skill analysis of selected flight experiments, (3) study results and conclusions, and (4) new technology.

  12. Effects on sustained performance of time-sharing a three-phase code transformation task /3P-COTRAN/.

    NASA Technical Reports Server (NTRS)

    Alluisi, E. A.; Morgan, B. B., Jr.

    1971-01-01

    A group of 20 highly trained subjects were divided randomly into five equal groups to time-share the 3P-COTRAN task with a different task combination of a multitask performance battery (MTPB) used by Alluisi (1969). The effects of the time-sharing on the 3P-COTRAN performance and the effects of 3P-COTRAN on the time-shared MTPB performances are analyzed.

  13. Space station data system analysis/architecture study. Task 2: Options development, DR-5. Volume 2: Design options

    NASA Technical Reports Server (NTRS)

    1985-01-01

    The primary objective of Task 2 is the development of an information base that will support the conduct of trade studies and provide sufficient data to make key design/programmatic decisions. This includes: (1) the establishment of option categories that are most likely to influence Space Station Data System (SSDS) definition; (2) the identification of preferred options in each category; and (3) the characterization of these options with respect to performance attributes, constraints, cost and risk. This volume contains the options development for the design category. This category comprises alternative structures, configurations and techniques that can be used to develop designs that are responsive to the SSDS requirements. The specific areas discussed are software, including data base management and distributed operating systems; system architecture, including fault tolerance and system growth/automation/autonomy and system interfaces; time management; and system security/privacy. Also discussed are space communications and local area networking.

  14. The development of landmark and beacon use in young children: evidence from a touchscreen search task.

    PubMed

    Sutton, Jennifer E

    2006-01-01

    Children ages 2, 3 and 4 years participated in a novel hide-and-seek search task presented on a touchscreen monitor. On beacon trials, the target hiding place could be located using a beacon cue, but on landmark trials, searching required the use of a nearby landmark cue. In Experiment 1, 2-year-olds performed less accurately than older children on landmark trials but performed equivalently on beacon trials. In Experiment 2, the number of items on the screen was reduced and 2-year-olds' performance improved. Use of the landmark transformation technique in Experiment 3 revealed that older children formed a more precise landmark-target spatial relationship than 2-year-olds. Experiment 4 showed that the transformation itself was not responsible for the youngest participants' decreased accuracy in Experiment 3. Overall, beacons were utilized effectively by all participants, but the use of landmark cues is refined between the ages of 2 and 4.

  15. TASK-3 knockout mice exhibit exaggerated nocturnal activity, impairments in cognitive functions, and reduced sensitivity to inhalation anesthetics.

    PubMed

    Linden, Anni-Maija; Sandu, Cristina; Aller, M Isabel; Vekovischeva, Olga Y; Rosenberg, Per H; Wisden, William; Korpi, Esa R

    2007-12-01

    The TASK-3 channel is an acid-sensitive two-pore-domain K+ channel, widely expressed in the brain and probably involved in regulating numerous neuronal populations. Here, we characterized the behavioral and pharmacological phenotypes of TASK-3 knockout (KO) mice. Circadian locomotor activity measurements revealed that the nocturnal activity of the TASK-3 KO mice was increased by 38% (P < 0.01) compared with wild-type littermate controls, light phase activity being similar. Although TASK-3 channels are abundant in cerebellar granule cells, the KO mice performed as well as the wild-type mice in walking on a rotating rod or along a 1.2-cm-diameter beam. However, they fell more frequently from a narrower 0.8-cm beam. The KO mice showed impaired working memory in the spontaneous alternation task, with the alternation percentage being 62 +/- 3% for the wild-type mice and 48 +/- 4% (P < 0.05) for the KO mice. Likewise, during training for the Morris water-maze spatial memory task, the KO mice were slower to find the hidden platform, and in the probe trial, the female KO mice visited fewer times the platform quadrant than the male KO and wild-type mice. In pharmacological tests, the TASK-3 KO mice showed reduced sensitivity to the inhalation anesthetic halothane and the cannabinoid receptor agonist WIN55212-2 mesylate [(R)-(+)-[2,3-dihydro-5-methyl-3-(4-morpholinylmethyl)pyrrolo[1,2,3-de]-1,4-benzoxazin-6-yl]-1-naphthalenylmethanone mesylate] but unaltered responses to the alpha2 adrenoceptor agonist dexmedetomidine, the i.v. anesthetic propofol, the opioid receptor agonist morphine, and the local anesthetic lidocaine. Overall, our results suggest important contributions of TASK-3 channels in the neuronal circuits regulating circadian rhythms, cognitive functions, and mediating specific pharmacological effects.

  16. TASK-3 knockout mice exhibit exaggerated nocturnal activity, impairments in cognitive functions, and reduced sensitivity to inhalation anesthetics.

    PubMed

    Linden, Anni-Maija; Sandu, Cristina; Aller, M Isabel; Vekovischeva, Olga Y; Rosenberg, Per H; Wisden, William; Korpi, Esa R

    2007-12-01

    The TASK-3 channel is an acid-sensitive two-pore-domain K+ channel, widely expressed in the brain and probably involved in regulating numerous neuronal populations. Here, we characterized the behavioral and pharmacological phenotypes of TASK-3 knockout (KO) mice. Circadian locomotor activity measurements revealed that the nocturnal activity of the TASK-3 KO mice was increased by 38% (P < 0.01) compared with wild-type littermate controls, light phase activity being similar. Although TASK-3 channels are abundant in cerebellar granule cells, the KO mice performed as well as the wild-type mice in walking on a rotating rod or along a 1.2-cm-diameter beam. However, they fell more frequently from a narrower 0.8-cm beam. The KO mice showed impaired working memory in the spontaneous alternation task, with the alternation percentage being 62 +/- 3% for the wild-type mice and 48 +/- 4% (P < 0.05) for the KO mice. Likewise, during training for the Morris water-maze spatial memory task, the KO mice were slower to find the hidden platform, and in the probe trial, the female KO mice visited fewer times the platform quadrant than the male KO and wild-type mice. In pharmacological tests, the TASK-3 KO mice showed reduced sensitivity to the inhalation anesthetic halothane and the cannabinoid receptor agonist WIN55212-2 mesylate [(R)-(+)-[2,3-dihydro-5-methyl-3-(4-morpholinylmethyl)pyrrolo[1,2,3-de]-1,4-benzoxazin-6-yl]-1-naphthalenylmethanone mesylate] but unaltered responses to the alpha2 adrenoceptor agonist dexmedetomidine, the i.v. anesthetic propofol, the opioid receptor agonist morphine, and the local anesthetic lidocaine. Overall, our results suggest important contributions of TASK-3 channels in the neuronal circuits regulating circadian rhythms, cognitive functions, and mediating specific pharmacological effects. PMID:17875609

  17. Development of a self-distancing task and initial validation of responses.

    PubMed

    Shepherd, Kathrine A; Coifman, Karin G; Matt, Lindsey M; Fresco, David M

    2016-07-01

    Mindfulness-based interventions are believed to counteract cognitive biases that exacerbate cognitive and physiological reactivity to emotional experiences and that contribute to the development and persistence of psychopathology. One process by which mindful practices may produce such salutary effects is by enhancing the capacity to "decenter"-or to adopt a self-distanced, nonjudgmental perspective on conscious experiences (e.g., thoughts, memories, and feelings). Findings consistently indicate that decentering, assessed via self-report, represents an important aspect of mental health and well-being; however, numerous researchers have called for more objective measures of skills associated with mindfulness and decentering to further evaluate the mechanisms and benefits of mindfulness-based practices. Thus, in the current investigation, we developed a behavioral task that requires mental manipulation of negative emotional (and neutral) material away from the self (self-distancing), as a means to assess the skills associated with mindfulness and decentering that likely underlie healthy emotional processing. In 2 nonmeditating, university samples, we found that higher levels of self-reported mindfulness and higher levels of 1 facet of decentering (the capacity to adopt a distanced perspective on experiences) predicted behavioral indicators of self-distancing. Results suggest that the self-distancing task shows considerable promise for capturing skills associated with mindfulness and at least 1 element of decentering. (PsycINFO Database Record

  18. Development of a self-distancing task and initial validation of responses.

    PubMed

    Shepherd, Kathrine A; Coifman, Karin G; Matt, Lindsey M; Fresco, David M

    2016-07-01

    Mindfulness-based interventions are believed to counteract cognitive biases that exacerbate cognitive and physiological reactivity to emotional experiences and that contribute to the development and persistence of psychopathology. One process by which mindful practices may produce such salutary effects is by enhancing the capacity to "decenter"-or to adopt a self-distanced, nonjudgmental perspective on conscious experiences (e.g., thoughts, memories, and feelings). Findings consistently indicate that decentering, assessed via self-report, represents an important aspect of mental health and well-being; however, numerous researchers have called for more objective measures of skills associated with mindfulness and decentering to further evaluate the mechanisms and benefits of mindfulness-based practices. Thus, in the current investigation, we developed a behavioral task that requires mental manipulation of negative emotional (and neutral) material away from the self (self-distancing), as a means to assess the skills associated with mindfulness and decentering that likely underlie healthy emotional processing. In 2 nonmeditating, university samples, we found that higher levels of self-reported mindfulness and higher levels of 1 facet of decentering (the capacity to adopt a distanced perspective on experiences) predicted behavioral indicators of self-distancing. Results suggest that the self-distancing task shows considerable promise for capturing skills associated with mindfulness and at least 1 element of decentering. (PsycINFO Database Record PMID:27078185

  19. Neuropsychological Assessment of a New Computerized Cognitive Task that Was Developed to Train Several Cognitive Functions Simultaneously

    PubMed Central

    Ichihara-Takeda, Satoe; Takeda, Kazuyoshi; Ikeda, Nozomu; Matsuyama, Kiyoji; Funahashi, Shintaro

    2016-01-01

    Recent studies have indicated that computerized cognitive training is effective as therapy for reducing the cognitive decline with aging and the dysfunction associated with neuropsychiatric illness. Although cognitive trainings that targets a specific function and multi-domain cognitive training have both been shown to have significant effects, we need one simple behavioral training paradigm to improve multiple domains of cognitive functions easily and simultaneously. We had developed a new computerized task that seeks to engage the cognitive functions of planning, mental calculation, and divergent thinking based on a working memory task in a single task. The purpose of this study was to assess the cognitive features of our new task by comparing the scores of seven known neuropsychological batteries in healthy elderly subjects. The relationships between performance in our task and the scores obtained by the neuropsychological batteries were examined. The percentage of correct performance on our task was correlated with the scores on the category fluency test, the digit span backward task, and the Trail making test B. Stepwise multiple regression analyses revealed that the scores on the category fluency test and the Trail making test B showed significant positive correlations with the percentage of correct performance on our task. Although the present study did not show high correlations between the percentage of correct performance on our task and working memory functions as a primary target, we observed mid-level correlations between the percentage of correct performance on our task and functions for divided attention and word fluency. Our new task requires not only working memory, but also attention and divergent thinking. Thus, this task might be a useful tool for training multiple cognitive functions simultaneously. PMID:27148110

  20. Neuropsychological Assessment of a New Computerized Cognitive Task that Was Developed to Train Several Cognitive Functions Simultaneously.

    PubMed

    Ichihara-Takeda, Satoe; Takeda, Kazuyoshi; Ikeda, Nozomu; Matsuyama, Kiyoji; Funahashi, Shintaro

    2016-01-01

    Recent studies have indicated that computerized cognitive training is effective as therapy for reducing the cognitive decline with aging and the dysfunction associated with neuropsychiatric illness. Although cognitive trainings that targets a specific function and multi-domain cognitive training have both been shown to have significant effects, we need one simple behavioral training paradigm to improve multiple domains of cognitive functions easily and simultaneously. We had developed a new computerized task that seeks to engage the cognitive functions of planning, mental calculation, and divergent thinking based on a working memory task in a single task. The purpose of this study was to assess the cognitive features of our new task by comparing the scores of seven known neuropsychological batteries in healthy elderly subjects. The relationships between performance in our task and the scores obtained by the neuropsychological batteries were examined. The percentage of correct performance on our task was correlated with the scores on the category fluency test, the digit span backward task, and the Trail making test B. Stepwise multiple regression analyses revealed that the scores on the category fluency test and the Trail making test B showed significant positive correlations with the percentage of correct performance on our task. Although the present study did not show high correlations between the percentage of correct performance on our task and working memory functions as a primary target, we observed mid-level correlations between the percentage of correct performance on our task and functions for divided attention and word fluency. Our new task requires not only working memory, but also attention and divergent thinking. Thus, this task might be a useful tool for training multiple cognitive functions simultaneously. PMID:27148110

  1. Early treated hypothyroidism: development at 3 years.

    PubMed Central

    Murphy, G; Hulse, J A; Jackson, D; Tyrer, P; Glossop, J; Smith, I; Grant, D

    1986-01-01

    Eighty children from the North West and North East Thames Regional Health Authorities who had been identified as having congenital hypothyroidism either by neonatal screening (76 cases) or by clinical symptoms (four) were seen for psychological assessments at 1 (60 cases), 3 (58), and/or 5 (20) years of age. Almost all the children's scores were in the normal range, and comparisons with matched controls suggested that they were doing only slightly less well than normal children in overall development. They were significantly slower, however, on a motor skills task. Moreover, a low initial serum thyroxine and triiodothyronine value, considerable delay in initial bone age, and an absence of thyroid tissue on isotope scan seemed to be associated with a somewhat poorer prognosis. PMID:3740924

  2. Development of "Task Value" Instrument for Biology as a School Subject

    ERIC Educational Resources Information Center

    Köksal, Mustafa Serdar; Yaman, Süleyman

    2013-01-01

    The expectancy-value model of motivation states that individuals' choice, persistence and performances are related to their beliefs about how much they value task. Despite the importance of "task value" in learning biology, lack of the instruments on task value for high school biology courses for practical use indicated requirement to…

  3. Development of a Language Impairment Screener for Spanish Speaking Children--SSLIC: Phase 1--Task Development

    ERIC Educational Resources Information Center

    Restrepo, M. Adelaida; Gorin, Joanna S.; Gray, Shelley; Morgan, Gareth P.; Barona, Nicole

    2010-01-01

    The main purpose of this study is to develop a Spanish language screening measure that (a) is valid and reliable for the purpose of identifying Spanish-speaking (SS) children at risk for Language Impairment (LI), (b) is valid and reliable across different Spanish dialects, different socioeconomic groups, and different ethnicities, (c) uses a…

  4. The development and preliminary psychometric evaluation of an attachment Implicit Association Task.

    PubMed

    Venta, Amanda; Jardin, Charles; Kalpakci, Allison; Sharp, Carla

    2016-01-01

    The importance of measuring attachment insecurity is underscored by a vast literature tying attachment insecurity to numerous psychological disorders. Self-report measures assess explicit attachment beliefs and experiences, while interview measures, like the Adult Attachment Interview, assess implicit internal working models about the self as worthy of care and others as reliable sources of care. The present study is a preliminary psychometric evaluation of a potentially cost-effective method of assessing implicit internal working models of attachment through the development of an Implicit Association Test (IAT). A racially diverse sample of 104 college females was administered Internet-based versions of three IATs (assessing views of the self, mother, and father) as well as self-report measures of attachment and interpersonal problems. Analyses were conducted to evaluate the (a) internal consistency of each task, (b) correlations among the tasks, (c) concurrent validity, and (d) convergent validity. Adequate internal consistency was noted and correlations among the three IATs were significant. No significant associations were observed between the explicit self-report measures of attachment and the IATs. Two primary areas for future research are discussed. First, future research should utilize an implicit attachment measure alongside an IAT. Second, future research should reevaluate the IAT stimuli used.

  5. Development and preliminary evaluation of a pediatric Spanish/English speech perception task

    PubMed Central

    Calandruccio, Lauren; Gomez, Bianca; Buss, Emily; Leibold, Lori J.

    2014-01-01

    Purpose To develop a task to evaluate children’s English and Spanish speech perception abilities in either noise or competing speech maskers. Methods Eight bilingual Spanish/English and eight age matched monolingual English children (ages 4.9 –16.4 years) were tested. A forced-choice, picture-pointing paradigm was selected for adaptively estimating masked speech reception thresholds. Speech stimuli were spoken by simultaneous bilingual Spanish/English talkers. The target stimuli were thirty disyllabic English and Spanish words, familiar to five-year-olds, and easily illustrated. Competing stimuli included either two-talker English or two-talker Spanish speech (corresponding to target language) and spectrally matched noise. Results For both groups of children, regardless of test language, performance was significantly worse for the two-talker than the noise masker. No difference in performance was found between bilingual and monolingual children. Bilingual children performed significantly better in English than in Spanish in competing speech. For all listening conditions, performance improved with increasing age. Conclusions Results indicate that the stimuli and task are appropriate for speech recognition testing in both languages, providing a more conventional measure of speech-in-noise perception as well as a measure of complex listening. Further research is needed to determine performance for Spanish-dominant listeners and to evaluate the feasibility of implementation into routine clinical use. PMID:24686915

  6. The development and preliminary psychometric evaluation of an attachment Implicit Association Task.

    PubMed

    Venta, Amanda; Jardin, Charles; Kalpakci, Allison; Sharp, Carla

    2016-01-01

    The importance of measuring attachment insecurity is underscored by a vast literature tying attachment insecurity to numerous psychological disorders. Self-report measures assess explicit attachment beliefs and experiences, while interview measures, like the Adult Attachment Interview, assess implicit internal working models about the self as worthy of care and others as reliable sources of care. The present study is a preliminary psychometric evaluation of a potentially cost-effective method of assessing implicit internal working models of attachment through the development of an Implicit Association Test (IAT). A racially diverse sample of 104 college females was administered Internet-based versions of three IATs (assessing views of the self, mother, and father) as well as self-report measures of attachment and interpersonal problems. Analyses were conducted to evaluate the (a) internal consistency of each task, (b) correlations among the tasks, (c) concurrent validity, and (d) convergent validity. Adequate internal consistency was noted and correlations among the three IATs were significant. No significant associations were observed between the explicit self-report measures of attachment and the IATs. Two primary areas for future research are discussed. First, future research should utilize an implicit attachment measure alongside an IAT. Second, future research should reevaluate the IAT stimuli used. PMID:27583812

  7. Professional Task-Based Curriculum Development for Distance Education Practitioners at Master's Level: A Design-Based Research

    ERIC Educational Resources Information Center

    Feng, Xiaoying; Lu, Guangxin; Yao, Zhihong

    2015-01-01

    Curriculum development for distance education (DE) practitioners is more and more focusing on practical requirements and competence development. Delphi and DACUM methods have been used at some universities. However, in the competency-based development area, these methods have been taken over by professional-task-based development in the last…

  8. Life science payload definition and integration study, task C and D. Volume 3: Appendices

    NASA Technical Reports Server (NTRS)

    1973-01-01

    Research equipment requirements were based on the Mini-7 and Mini-30 laboratory concepts defined in Tasks A and B of the intial LSPD contract. Modified versions of these laboratories and the research equipment within them were to be used in three missions of Shuttle/Sortie Module. These were designated (1) the shared 7-day laboratory (a mission with the life sciences laboratory sharing the sortie module with another scientific laboratory), (2) the dedicated 7-day laboratory (full use of the sortie module), and (3) the dedicated 30-day laboratory (full sortie module use with a 30-day mission duration). In defining the research equipment requirements of these laboratories, the equipment was grouped according to its function, and equipment unit data packages were prepared.

  9. Development anmd testing of electrophoresis solutions. Task I.1: Development of optimal buffer system

    NASA Technical Reports Server (NTRS)

    1985-01-01

    Two buffers were explored for testing: low ionic strength electrophoresis buffer with and without density gradient material. It was found that the electrophoresis routine was better tolerated when Ficoll was present. The results of a viability study of primary human fetal kidney (HFK-1) cells at the first passage are shown. Cell strain HFK-1 was used in several experiments at the first and second passage. The HFK consisted mainly of fibroblasts, and HFK-1 has a high epithelioid cell content. The chromosomes of HFK were examined and found to be euploid. The stock medium for cell electrophoresis is described. In this solution density gradient solutes such as sucrose and Ficoll are dissolved to bring the osmolarity to 0.30. Its ionic strength is less than 0.01M, and its conductivity is usually 0.0011 mho/cm. Methods for viability determination included direct microscopic counting of the percent cells attached and spread within 24 hr of plating test cultures or electrophoretically separated fractions. The Cytograf viability assay concept was tested, and shown that blue stained cells scatter less light into the 0.8 to 3.3 deg angular interval than do unstained cells.

  10. TRPV3 in Drug Development

    PubMed Central

    Broad, Lisa M.; Mogg, Adrian J.; Eberle, Elizabeth; Tolley, Marcia; Li, Dominic L.; Knopp, Kelly L.

    2016-01-01

    Transient receptor potential vanilloid 3 (TRPV3) is a member of the TRP (Transient Receptor Potential) super-family. It is a relatively underexplored member of the thermo-TRP sub-family (Figure 1), however, genetic mutations and use of gene knock-outs and selective pharmacological tools are helping to provide insights into its role and therapeutic potential. TRPV3 is highly expressed in skin, where it is implicated in skin physiology and pathophysiology, thermo-sensing and nociception. Gain of function TRPV3 mutations in rodent and man have enabled the role of TRPV3 in skin health and disease to be particularly well defined. Pre-clinical studies provide some rationale to support development of TRPV3 antagonists for therapeutic application for the treatment of inflammatory skin conditions, itch and pain. However, to date, only one compound directed towards block of the TRPV3 receptor (GRC15300) has progressed into clinical trials. Currently, there are no known clinical trials in progress employing a TRPV3 antagonist. PMID:27618069

  11. TRPV3 in Drug Development.

    PubMed

    Broad, Lisa M; Mogg, Adrian J; Eberle, Elizabeth; Tolley, Marcia; Li, Dominic L; Knopp, Kelly L

    2016-01-01

    Transient receptor potential vanilloid 3 (TRPV3) is a member of the TRP (Transient Receptor Potential) super-family. It is a relatively underexplored member of the thermo-TRP sub-family (Figure 1), however, genetic mutations and use of gene knock-outs and selective pharmacological tools are helping to provide insights into its role and therapeutic potential. TRPV3 is highly expressed in skin, where it is implicated in skin physiology and pathophysiology, thermo-sensing and nociception. Gain of function TRPV3 mutations in rodent and man have enabled the role of TRPV3 in skin health and disease to be particularly well defined. Pre-clinical studies provide some rationale to support development of TRPV3 antagonists for therapeutic application for the treatment of inflammatory skin conditions, itch and pain. However, to date, only one compound directed towards block of the TRPV3 receptor (GRC15300) has progressed into clinical trials. Currently, there are no known clinical trials in progress employing a TRPV3 antagonist. PMID:27618069

  12. Engineering task plan for upgrades to the leveling jacks on core sample trucks number 3 and 4

    SciTech Connect

    KOSTELNIK, A.J.

    1999-02-24

    Characterizing the waste in underground storage tanks at the Hanford Site is accomplished by obtaining a representative core sample for analysis. Core sampling is one of the numerous techniques that have been developed for use given the environmental and field conditions at the Hanford Site. Core sampling is currently accomplished using either Push Mode Core Sample Truck No.1 or; Rotary Mode Core Sample Trucks No.2, 3 or 4. Past analysis (WHC 1994) has indicated that the Core Sample Truck (CST) leveling jacks are structurally inadequate when lateral loads are applied. WHC 1994 identifies many areas where failure could occur. All these failures are based on exceeding the allowable stresses listed in the American Institute of Steel Construction (AISC) code. The mode of failure is for the outrigger attachments to the truck frame to fail resulting in dropping of the CST and possible overturning (Ref. Ziada and Hundal, 1996). Out of level deployment of the truck can exceed the code allowable stresses in the structure. Calculations have been performed to establish limits for maintaining the truck level when lifting. The calculations and the associated limits are included in appendix A. The need for future operations of the CSTS is limited. Sampling is expected to be complete in FY-2001. Since there is limited time at risk for continued use of the CSTS with the leveling controls without correcting the structural problems, there are several design changes that could give incremental improvements to the operational safety of the CSTS with limited impact on available operating time. The improvements focus on making the truck easier to control during lifting and leveling. Not all of the tasks identified in this ETP need to be performed. Each task alone can improve the safety. This engineering task plan is the management plan document for implementing the necessary additional structural analysis. Any additional changes to meet requirements of standing orders shall require a

  13. Hydrothermal processing of Hanford tank waste. Organic destruction technology development task annual report -- FY 1993

    SciTech Connect

    Orth, R.J.; Schmidt, A.J.; Zacher, A.H.

    1993-09-01

    Low-temperature hydrothermal processing (HTP) is a thermal-chemical autogenous processing method that can be used to destroy organics and ferrocyanide in Hanford tank waste at temperatures from 250 C to 400 C. With HTP, organics react with oxidants, such as nitrite and nitrate, already present in the waste. Ferrocyanides and free cyanide will hydrolyze at similar temperatures and may also react with nitrates or other oxidants in the waste. No air or oxygen or additional chemicals need to be added to the autogenous HTP system. However, enhanced kinetics may be realized by air addition, and, if desired, chemical reductants can be added to the system to facilitate complete nitrate/nitrate destruction. Tank waste can be processed in a plug-flow, tubular reactor, or a continuous-stirred tank reactor system designed to accommodate the temperature, pressure, gas generation, and heat release associated with decomposition of the reactive species. The work described in this annual report was conducted in FY 1993 for the Organic Destruction Technology Development Task of Hanford`s Tank Waste Remediation System (TWRS). This task is part of an overall program to develop organic destruction technologies originally funded by TWRS to meet tank safety and waste form disposal criteria and condition the feed for further pretreatment. During FY 1993 the project completed seven experimental test plans, a 30-hr pilot-scale continuous run, over 200 hr of continuous bench-scale HTP testing, and 20 batch HTP tests; two contracts were established with commercial vendors, and a commercial laboratory reactor was procured and installed in a glovebox for HTP testing with actual Hanford tank waste.

  14. Novel hydrogen separation device development for coal gasification system applications. Task 1

    SciTech Connect

    Not Available

    1991-12-01

    This report summarizes all results obtained under Task 1, Operation and Parameter Testing using Subscale Cells. Stable Electrochemical Hydrogen Separation Device (EHSD) operation was demonstrated with the 4,400 hour life test of an EHSD. It was found that N{sub 2}, C0{sub 2} and CH{sub 4} behave as equivalent inerts; EHSD performance is not affected by the balance of feed gas containing these components. High H{sub 2} purity, >99%, is one of the main features of the EHSD. This product purity level is not sacrificed by increased H{sub 2} recovery. Co, however, does adversely affect EHSD performance and therefore feed stream pretreatment is recommended. Concentrations up to 10 ppM H{sub 2}S and NH{sub 3} were added to the feed gas stream to determine their effect on EHSD performance. These impurities did not affect EHSD performance.

  15. TASK 2.5.4 DEVELOPMENT OF AN ENERGY SAVINGS CALCULATOR

    SciTech Connect

    Miller, William A; New, Joshua Ryan; Desjarlais, Andre Omer; Huang, Joe; Erdem, Ender; Ronnen, Levinson

    2010-03-01

    California s major energy utilities and the California Energy Commission (CEC) are seeking to allocate capital that yields the greatest return on investment for energy infrastructure that meets any part of the need for reliable supplies of energy. The utilities are keenly interested in knowing the amount of electrical energy savings that would occur if cool roof color materials are adopted in the building market. To meet this need the Oak Ridge National Laboratory and the Lawrence Berkeley National Laboratory (LBNL) have been collaborating on a Public Interest Energy Research (PIER) project to develop an industry-consensus energy-savings calculator. The task was coordinated with an ongoing effort supported by the DOE to develop one calculator to achieve both the DOE and the EPA objectives for deployment of cool roof products. Recent emphasis on domestic building energy use has made the work a top priority by the Department of Energy s (DOE) Building Technologies Program. The Roof Savings Calculator (RSC) tool is designed to help building owners, manufacturers, distributors, contractors and practitioners easily run complex simulations. The latest web technologies and usability design were employed to provide an easy input interface to an annual simulation of hour-by-hour, whole-building performance using the world-class simulation tools DOE-2.1E and AtticSim. Building defaults were assigned based on the best available statistical evidence and can provide energy and cost savings after the user selects nothing more than the building location. A key goal for the tool is to promote the energy benefits of cool color tile, metal and asphalt shingle roof products and other energy saving systems. The RSC tool focuses on applications for the roof and attic; however, the code conducts a whole building simulation that puts the energy and heat flows of the roof and attic into the perspective of the whole house. An annual simulation runs in about 30 sec. In addition to cool

  16. Anticipatory Action Planning Increases from 3 to 10 Years of Age in Typically Developing Children

    ERIC Educational Resources Information Center

    Jongbloed-Pereboom, Marjolein; Nijhuis-van der Sanden, Maria W. G.; Saraber-Schiphorst, Nicole; Craje, Celine; Steenbergen, Bert

    2013-01-01

    The primary aim of this study was to assess the development of action planning in a group of typically developing children aged 3 to 10 years (N = 351). The second aim was to assess reliability of the action planning task and to relate the results of the action planning task to results of validated upper limb motor performance tests. Participants…

  17. Field Testing of a Wet FGD Additive for Enhanced Mercury Control - Task 3 Full-scale Test Results

    SciTech Connect

    Gary Blythe

    2007-05-01

    This Topical Report summarizes progress on Cooperative Agreement DE-FC26-04NT42309, 'Field Testing of a Wet FGD Additive'. The objective of the project is to demonstrate the use of a flue gas desulfurization (FGD) additive, Degussa Corporation's TMT-15, to prevent the reemission of elemental mercury (Hg{sup 0}) in flue gas exiting wet FGD systems on coal-fired boilers. Furthermore, the project intends to demonstrate whether the additive can be used to precipitate most of the mercury (Hg) removed in the wet FGD system as a fine TMT salt that can be separated from the FGD liquor and bulk solid byproducts for separate disposal. The project is conducting pilot- and full-scale tests of the TMT-15 additive in wet FGD absorbers. The tests are intended to determine required additive dosages to prevent Hg{sup 0} reemissions and to separate mercury from the normal FGD byproducts for three coal types: Texas lignite/Power River Basin (PRB) coal blend, high-sulfur Eastern bituminous coal, and low-sulfur Eastern bituminous coal. The project team consists of URS Group, Inc., EPRI, TXU Generation Company LP, Southern Company, and Degussa Corporation. TXU Generation has provided the Texas lignite/PRB cofired test site for pilot FGD tests, Monticello Steam Electric Station Unit 3. Southern Company is providing the low-sulfur Eastern bituminous coal host site for wet scrubbing tests, as well as the pilot- and full-scale jet bubbling reactor (JBR) FGD systems to be tested. IPL, an AES company, provided the high-sulfur Eastern bituminous coal full-scale FGD test site and cost sharing. Degussa Corporation is providing the TMT-15 additive and technical support to the test program as cost sharing. The project is being conducted in six tasks. Of the six project tasks, Task 1 involves project planning and Task 6 involves management and reporting. The other four tasks involve field testing on FGD systems, either at pilot or full scale. The four tasks include: Task 2 - Pilot Additive Testing

  18. Development and Validation of Career Development Guidelines by Task/Activity Analysis of Occupational Safety and Health Professions: Industrial Hygiene and Safety Professional. Final Report. Technical Report XII.

    ERIC Educational Resources Information Center

    Vernon, Ralph J.; And Others

    This report summarizes research findings which resulted in development of curricula for occupational safety and health professions based on task/activity analyses and related performance objectives. The first seven chapters focus on the seven objectives. Chapter 1, Literature Review and Selection of Employers, concerns tasks required for…

  19. Integration of classroom science performance assessment tasks by participants of the Wisconsin Performance Assessment Development Project (WPADP)

    NASA Astrophysics Data System (ADS)

    Tonnis, Dorothy Ann

    The goals of this interpretive study were to examine selected Wisconsin science teachers' perceptions of teaching and learning science, to describe the scope of classroom performance assessment practices, and to gain an understanding of teachers' personal and professional experiences that influenced their belief systems of teaching, learning and assessment. The study was designed to answer the research questions: (1) How does the integration of performance assessment relate to the teachers' views of teaching and learning? (2) How are the selected teachers integrating performance assessment in their teaching? (3) What past personal and professional experiences have influenced teachers' attitudes and beliefs related to their classroom performance assessment practices? Purposeful sampling was used to select seven Wisconsin elementary, middle and high school science teachers who participated in the WPADP initiative from 1993-1995. Data collection methods included a Teaching Practices Inventory (TPI), semi-structured interviews, teacher developed portfolios, portfolio conferences, and classroom observations. Four themes and multiple categories emerged through data analysis to answer the research questions and to describe the results. Several conclusions were drawn from this research. First, science teachers who appeared to effectively integrate performance assessment, demonstrated transformational thinking in their attitudes and beliefs about teaching and learning science. In addition, these teachers viewed assessment and instructional practices as interdependent. Third, transformational teachers generally used well defined criteria to judge student work and made it public to the students. Transformational teachers provided students with real-world performance assessment tasks that were also learning events. Furthermore, student task responses informed the transformational teachers about effectiveness of instruction, students' complex thinking skills, quality of

  20. Steering Demands Diminish the Early-P3, Late-P3 and RON Components of the Event-Related Potential of Task-Irrelevant Environmental Sounds

    PubMed Central

    Scheer, Menja; Bülthoff, Heinrich H.; Chuang, Lewis L.

    2016-01-01

    The current study investigates the demands that steering places on mental resources. Instead of a conventional dual-task paradigm, participants of this study were only required to perform a steering task while task-irrelevant auditory distractor probes (environmental sounds and beep tones) were intermittently presented. The event-related potentials (ERPs), which were generated by these probes, were analyzed for their sensitivity to the steering task’s demands. The steering task required participants to counteract unpredictable roll disturbances and difficulty was manipulated either by adjusting the bandwidth of the roll disturbance or by varying the complexity of the control dynamics. A mass univariate analysis revealed that steering selectively diminishes the amplitudes of early P3, late P3, and the re-orientation negativity (RON) to task-irrelevant environmental sounds but not to beep tones. Our findings are in line with a three-stage distraction model, which interprets these ERPs to reflect the post-sensory detection of the task-irrelevant stimulus, engagement, and re-orientation back to the steering task. This interpretation is consistent with our manipulations for steering difficulty. More participants showed diminished amplitudes for these ERPs in the “hard” steering condition relative to the “easy” condition. To sum up, the current work identifies the spatiotemporal ERP components of task-irrelevant auditory probes that are sensitive to steering demands on mental resources. This provides a non-intrusive method for evaluating mental workload in novel steering environments. PMID:26973494

  1. Using Web-Based Exploratory Tasks to Develop Intercultural Competence in a Homogeneous Cultural Environment

    ERIC Educational Resources Information Center

    Stockwell, Esther

    2016-01-01

    This study adapted web-based exploratory tasks using WebQuests as a means of enabling students to understand and reflect on both the target and their own culture. Learners actively used various authentic resources selected to meet their linguistic and cognitive needs to complete the tasks. The aim of this study was to help Japanese university…

  2. Developing Multiplicative Thinking with Rectangular Array Tasks in a Computer Environment

    ERIC Educational Resources Information Center

    Huang, Amy I-Yu

    2013-01-01

    This study reports findings from a teaching experiment in which 4th grade children engaged in solving multiplication tasks with rectangular arrays in a computer environment. The environment provided flexible task-solving through dynamic virtual manipulatives (VMs) so children could use their existing knowledge of multiplication to complete array…

  3. CERAMIC MEMBRANE ENABLING TECHNOLOGY FOR IMPROVED IGCC EFFICIENCY

    SciTech Connect

    Ravi Prasad

    2004-09-01

    This quarterly technical progress report will summarize work accomplished for Phase 2 Program during the quarter April to June 2004. In task 1, long term testing of OTM elements at different temperatures and process conditions continued. In task 2, OTM elements were manufactured as necessary for task 1. In task 7, advanced OTM and cryogenic IGCC cases for near-term integration were developed, leading to cost requirements for commercial viability. In task 9, discussion with DOE regarding restructuring the program for subsequent phases were initiated. The objectives of the second year of phase 2 of the program are to construct and operate an engineering pilot reactor for OTM oxygen. Work to support this objective is being undertaken in the following areas in this quarter: Element reliability; Element fabrication; and IGCC process analysis and economics. The major accomplishments this quarter were: Long term life test of OTM element passed nine months at different testing conditions.

  4. Selection of an industrial natural-gas-fired advanced turbine system - Task 3A

    SciTech Connect

    Holloway, G.M.

    1997-05-01

    TASK OBJECTIVES: Identify a gas-fueled turbine and steam system which will meet the program goals for efficiency - and emissions. TECHNICAL GOALS AND REQUIREMENTS: Goals for the Advanced Turbine System Program (ATS) where outlined in the statement of work for five basic categories: Cycle Efficiency - System heat rate to have a 15% improvement over 1991 vintage systems being offered to the market. Environmental No post-combustion devices while meeting the following parameter targets: (1) Nitrous Oxide (NO{sub x}) emissions to equal 8 parts per million dry (ppmd) with 15% oxygen. (2) Carbon monoxide (CO) and unburned hydrocarbon (UHC) emissions to equal 20 parts per million(ppmd) each. Cost of electricity to be 10 percent less when compared to similar 1991 systems. Fuel Flexibility Have to ability to burn coal or coal derived fuels without extensive redesign. Reliability, Availability, Maintainability Reliability, availability and maintainability must be comparable to modern advanced power generation systems. For all cycle and system studies, analyses were done for the following engine system ambient conditions: Temperature - 59F; Altitude - Sea Level; Humidity - 60%. For the 1991 reference system, GE Aircraft Engines used its LM6OOO engine product offering for comparison of the Industrial System parameters developed under this program.

  5. Early Oral Language Comprehension, Task Orientation, and Foundational Reading Skills as Predictors of Grade 3 Reading Comprehension

    ERIC Educational Resources Information Center

    Lepola, Janne; Lynch, Julie; Kiuru, Noona; Laakkonen, Eero; Niemi, Pekka

    2016-01-01

    The present five-year longitudinal study from preschool to grade 3 examined the developmental associations among oral language comprehension, task orientation, reading precursors, and reading fluency, as well as their role in predicting grade 3 reading comprehension. Ninety Finnish-speaking students participated in the study. The students' oral…

  6. Midline Crossing: Developmental Trend from 3 to 10 Years of Age in a Preferential Card-Reaching Task

    ERIC Educational Resources Information Center

    Carlier, M.; Doyen, A.-L.; Lamard, C.

    2006-01-01

    We assessed 110 left-handed and 322 right-handed children aged from 3 to 10 years, using Bishop's card-reaching task. Manual body midline crossings were observed. A regular developmental trend was observed from 3 to 10 years: older children crossed the body midline more frequently when reaching for cards than did younger children. The factor age…

  7. Approximating Implicit and Explicit Mentalizing with Two Naturalistic Video-Based Tasks in Typical Development and Autism Spectrum Disorder

    ERIC Educational Resources Information Center

    Rosenblau, Gabriela; Kliemann, Dorit; Heekeren, Hauke R.; Dziobek, Isabel

    2015-01-01

    Individuals with autism spectrum disorder (ASD) have been proposed to show greater impairments in implicit than explicit mentalizing. To test this proposition, we developed two comparable naturalistic tasks for a performance-based approximation of implicit and explicit mentalizing in 28 individuals with ASD and 23 matched typically developed (TD)…

  8. Development of objective discomfort evaluation indicators for a task-oriented motion using less constrained motion concept: application to automotive pedal clutching task.

    PubMed

    Romain, Pannetier; Xuguang, Wang

    2012-01-01

    This paper presents a method to develop objective discomfort evaluation indicators for a task oriented motion using the concept of less constrained movement. The basic idea is to compare imposed and less constrained movements in order to identify relevant biomechanical parameters for defining objective discomfort indicators. The task of automotive pedal clutching was chosen for illustrating the proposed method. Based on discomfort questionnaire and motion analysis of the experimental data, four discomfort indicators were proposed. Two of them were based on the ankle joint angle around flexion/extension axis at the beginning and the end of the clutch pedal depression. The third one was defined using knee flexion/extension joint torque at the end of the clutch pedal depression. The last indicator was defined as the relative lateral position of the heel compared to the average pedal lateral position for less constrained configurations. A global discomfort function was also defined as a weighted sum of all indicators. Globally, the proposed global discomfort indicator succeeded in differentiating the tested configurations in agreement with experimental observation. As expected, less discomfort rating is obtained for less constrained movement when compared with the corresponding imposed one.

  9. Approximating implicit and explicit mentalizing with two naturalistic video-based tasks in typical development and autism spectrum disorder.

    PubMed

    Rosenblau, Gabriela; Kliemann, Dorit; Heekeren, Hauke R; Dziobek, Isabel

    2015-04-01

    Individuals with autism spectrum disorder (ASD) have been proposed to show greater impairments in implicit than explicit mentalizing. To test this proposition, we developed two comparable naturalistic tasks for a performance-based approximation of implicit and explicit mentalizing in 28 individuals with ASD and 23 matched typically developed (TD) participants. Although both tasks were sensitive to the social impairments of individuals with ASD, implicit mentalizing was not more dysfunctional than explicit mentalizing. In TD participants, performance on the tasks did not correlate with each other, whereas in individuals with ASD they were highly correlated. These findings suggest that implicit and explicit mentalizing processes are separable in typical development. In contrast, in individuals with ASD implicit and explicit mentalizing processes are similarly impaired and closely linked suggesting a lack of developmental specification of these processes in ASD.

  10. Mathematics and Science Task Force Report.

    ERIC Educational Resources Information Center

    Wisconsin Univ., Green Bay. Inst. for Learning Partnership.

    This document presents a report from the Mathematics and Science Task Force. The Task Force held its initial meeting on January 27, 1999 to develop essential competencies in content knowledge and pedagogy in four areas: (1) elementary mathematics; (2) secondary mathematics; (3) elementary science; and (4) secondary science. Initially Task Force…

  11. The development of end- and beginning-state comfort in a cup manipulation task.

    PubMed

    Scharoun, Sara M; Bryden, Pamela J

    2014-04-01

    End-state comfort (ESC) is the tendency to assume comfortable postures at the end of simple object manipulation rather than at the start; and therefore has been used to assess the behavioral effects of motor planning. Adult-like patterns have been observed at age 9. Observations can extend to joint-action, such that adults consider the beginning-state comfort (BSC) of another, without sacrificing ESC; however, trends in children have yet to be delineated. This study investigated the development of ESC and BSC in a cup manipulation task. Three to 12-year-olds and adults were asked to pick up a cup and (1) pour a glass of water or (2) pass it to the researcher to pour. Paralleling previous findings, adult-like patterns of ESC were observed at age 9. Adding to the literature, adult-like evidence of BSC emerged at the age of 7. Therefore, 7-year-olds consider another's BSC; however, cannot facilitate ESC until age 9. PMID:23532951

  12. Effect of Visuo-Motor Co-location on 3D Fitts' Task Performance in Physical and Virtual Environments

    PubMed Central

    Fu, Michael J.; Hershberger, Andrew D.; Sano, Kumiko; Çavuşoğlu, M. Cenk

    2013-01-01

    Given the ease that humans have with using a keyboard and mouse in typical, non-colocated computer interaction, many studies have investigated the value of co-locating the visual field and motor workspaces using immersive display modalities. Significant understanding has been gained by previous work comparing physical tasks against virtual tasks, visuo-motor co-location versus non-colocation, and even visuo-motor rotational misalignments in virtual environments (VEs). However, few studies have explored all of these paradigms in context with each other and it is difficult to perform inter-study comparisons because of the variation in tested motor tasks. Therefore, using a stereoscopic fish tank display setup, the goal for the current study was to characterize human performance of a 3D Fitts' point-to-point reaching task using a stylus-based haptic interface in the physical, co-located/non-colocated, and rotated VE visualization conditions.Five performance measures – throughput, initial movement error, corrective movements, and peak velocity – were measured and used to evaluate task performance. These measures were studied in 22 subjects (11 male, 11 female, ages 20–32) performing a 3D variant of Fitts' serial task under 10 task conditions: physical, co-located VE, non-colocated VE, and rotated VEs from 45–315° in 45° increments. Hypotheses All performance measures in the co-located VE were expected to reflect significantly reduced task performance over the real condition, but also reflect increased performance over the non-colocated VE condition. For rotational misalignments, all performance measures were expected to reflect highest performance at 0°, reduce to lowest performance at 90° and rise again to a local maximum at 180° (symmetric about 0°). Results All performance measures showed that the co-located VE condition resulted in significantly lower task performance than the physical condition and higher mean performance than the non-colocated VE

  13. Electric Vehicle Preparedness Task 3: Detailed Assessment of Target Electrification Vehicles at Joint Base Lewis McChord Utilization

    SciTech Connect

    Stephen Schey; Jim Francfort

    2014-08-01

    Task 2 involved identifying daily operational characteristics of select vehicles and initiating data logging of vehicle movements in order to characterize the vehicle’s mission. Individual observations of these selected vehicles provide the basis for recommendations related to PEV adoption and whether a battery electric vehicle (BEV) or plug-in hybrid electric vehicle (PHEV) (collectively PEVs) can fulfill the mission requirements and provides observations related to placement of PEV charging infrastructure. This report provides the results of the data analysis and observations related to the replacement of current vehicles with PEVs. This fulfills part of the Task 3 requirements. Task 3 also includes an assessment of charging infrastructure required to support this replacement. That is the subject of a separate report.

  14. Test plan. GCPS task 7, subtask 7.1: IHM development

    NASA Technical Reports Server (NTRS)

    Greenberg, H. S.

    1994-01-01

    The overall objective of Task 7 is to identify cost-effective life cycle integrated health management (IHM) approaches for a reusable launch vehicle's primary structure. Acceptable IHM approaches must: eliminate and accommodate faults through robust designs, identify optimum inspection/maintenance periods, automate ground and on-board test and check-out, and accommodate and detect structural faults by providing wide and localized area sensor and test coverage as required. These requirements are elements of our targeted primary structure low cost operations approach using airline-like maintenance by exception philosophies. This development plan will follow an evolutionary path paving the way to the ultimate development of flight-quality production, operations, and vehicle systems. This effort will be focused on maturing the recommended sensor technologies required for localized and wide area health monitoring to a technology readiness level (TRL) of 6 and to establish flight ready system design requirements. The following is a brief list of IHM program objectives: design out faults by analyzing material properties, structural geometry, and load and environment variables and identify failure modes and damage tolerance requirements; design in system robustness while meeting performance objectives (weight limitations) of the reusable launch vehicle primary structure; establish structural integrity margins to preclude the need for test and checkout and predict optimum inspection/maintenance periods through life prediction analysis; identify optimum fault protection system concept definitions combining system robustness and integrity margins established above with cost effective health monitoring technologies; and use coupons, panels, and integrated full scale primary structure test articles to identify, evaluate, and characterize the preferred NDE/NDI/IHM sensor technologies that will be a part of the fault protection system.

  15. Development of orthogonal task designs in fMRI studies of higher cognition: The NIMH experience

    PubMed Central

    2012-01-01

    This paper chronicles one researcher’s journey at the National Institute of Mental Health, exploring ways to understand the neural systems responsible for the cognitive sub-processes of working memory tasks. Both the opportunities and the pitfalls with applying the idea of cognitive subtraction to neuroimaging data were well-known from studies using positron emission tomography. We took advantage of the improved temporal resolution of fMRI with a delayed-recognition task and identified the time-courses of the different stages of the task (encoding, memory delay, and recognition test) as predictor variables in a multiple regression analysis. Because these signals were temporally independent, individual components of tasks could be contrasted with one another, rather than entire tasks, reducing the problem of violations of pure insertion in cognitive subtraction. This approach enabled us to draw more detailed conclusions about the neural systems of higher cognition and the organization of prefrontal cortex than had been possible before fMRI. Further enhancements and innovations over the last 20 years by a multitude of researchers across the field have greatly expanded this knowledge, but this approach called “orthogonal task design” has remained a fundamental component of many of these modern studies. PMID:22245651

  16. Far infrared fusion plasma diagnostics. Task 3A, Progress report, FY 1990

    SciTech Connect

    Luhmann, N.C. Jr.; Peebles, W.A.

    1990-12-31

    Over the last several years, reflectometry has grown in importance as a diagnostic for both steady-state density Profiles as well as for the investigation of density fluctuations and turbulence. As a diagnostic for density profile measurement, it is generally believed to be well understood in the tokamak environment. However, its use as a fluctuation diagnostic is hampered by a lack of quantitative experimental understanding of its wavenumber sensitivity and spatial resolution. Several researchers, have theoretically investigated these questions. However, prior to the UCLA laboratory investigation, no group has experimentally investigated these questions. Because of the reflectometer`s importance to the world effort in understanding plasma turbulence and transport, UCLA has, over the last year, made its primary Task IIIA effort the resolution of these questions. UCLA has taken the lead in a quantitative experimental understanding of reflectometer data as applied to the measurement of density fluctuations. In addition to this, work has proceeded on the design, construction, and installation of a reflectometer system on UCLA`s CCT tokamak. This effort will allow a comparison between the improved confinement regimes (H-mode) observed on both the DIII-D and CCT machines with the goal of achieving a physics understanding of the phenomena. Preliminary investigation of a new diagnostic technique to measure density profiles as a function of time has been initiated at UCLA. The technique promises to be a valuable addition to the range of available plasma diagnostics. Work on advanced holographic reflectometry technique as applied to fluctuation diagnostics has awaited a better understanding of the reflectometer signal itself as discussed above. Efforts to ensure the transfer of the diagnostic developments have continued with particular attention devoted to the preliminary design of a multichannel FIR interferometer for MST.

  17. Effect of Visuo-Haptic Co-location on 3D Fitts’ Task Performance

    PubMed Central

    Fu, Michael J.; Hershberger, Andrew D.; Sano, Kumiko; Çavuşoğlu, M. Cenk

    2013-01-01

    Given the ease that humans have with using a keyboard and mouse in typical, non-colocated computer interaction, many studies have investigated the value of colocating the visual field and haptic workspaces using immersive virtual reality (VR) modalities. Significant understanding has been gained by previous work comparing physical tasks against VR tasks, visuo-haptic co-location versus non-colocation, and even visuo-haptic rotational misalignments in VR. However, few studies have explored all of these paradigms in context with each other and it is difficult to do inter-study comparisons because of the variation in tested motor tasks. Therefore, the goal for the current study was to characterize human performance of Fitts’ point-to-point reaching task – an established test of manual performance – in the physical, co-located/non-colocated VR, and rotated VR visualization conditions. A key finding was the significant decrease observed in end-point error for tasks performed in a co-located virtual reality environment. The results also showed cyclic performance degradations due to rotational visuo-haptic misalignments that were consistent with trends reported by the literature. PMID:24511428

  18. Task 6.3. Applying Genetic and Epigenetic Data to Inform Susceptibility

    EPA Science Inventory

    This poster describes Topic 3, Project 6, of the HHRA plan. It addresses the need to move beyond traditional risk assessment practices by developing cumulative risk assessment (CRA) methods to integrate and evaluate impacts of chemical and nonchemical stressors on the environmen...

  19. The Measurement of Executive Function at Age 3 Years: Psychometric Properties and Criterion Validity of a New Battery of Tasks

    ERIC Educational Resources Information Center

    Willoughby, Michael T.; Blair, Clancy B.; Wirth, R. J.; Greenberg, Mark

    2010-01-01

    In this study, the authors examined the psychometric properties and criterion validity of a newly developed battery of tasks that were designed to assess executive function (EF) abilities in early childhood. The battery was included in the 36-month assessment of the Family Life Project (FLP), a prospective longitudinal study of 1,292 children…

  20. Ion channel profile of TRPM8 cold receptors reveals a role of TASK-3 potassium channels in thermosensation.

    PubMed

    Morenilla-Palao, Cruz; Luis, Enoch; Fernández-Peña, Carlos; Quintero, Eva; Weaver, Janelle L; Bayliss, Douglas A; Viana, Félix

    2014-09-11

    Animals sense cold ambient temperatures through the activation of peripheral thermoreceptors that express TRPM8, a cold- and menthol-activated ion channel. These receptors can discriminate a very wide range of temperatures from innocuous to noxious. The molecular mechanism responsible for the variable sensitivity of individual cold receptors to temperature is unclear. To address this question, we performed a detailed ion channel expression analysis of cold-sensitive neurons, combining bacterial artificial chromosome (BAC) transgenesis with a molecular-profiling approach in fluorescence-activated cell sorting (FACS)-purified TRPM8 neurons. We found that TASK-3 leak potassium channels are highly enriched in a subpopulation of these sensory neurons. The thermal threshold of TRPM8 cold neurons is decreased during TASK-3 blockade and in mice lacking TASK-3, and, most importantly, these mice display hypersensitivity to cold. Our results demonstrate a role of TASK-3 channels in thermosensation, showing that a channel-based combinatorial strategy in TRPM8 cold thermoreceptors leads to molecular specialization and functional diversity. PMID:25199828

  1. Sustainable Energy Solutions Task 3.0:Life-Cycle Database for Wind Energy Systems

    SciTech Connect

    Janet M Twomey, PhD

    2010-04-30

    research has developed a fundamental approach. The emphasis was place on individual unit processes as an organizing framework to understand the life cycle of manufactured products. The rearrangement of unit processes provides an efficient and versatile means of understanding improved manufactured products such as wind generators. The taxonomy and structure of unit process lci were developed in this project. A series of ten unit process lci were developed to sample the major segments of the manufacturing unit process taxonomy. Technical and economic effectiveness has been a focus of the project research in Task three. The use of repeatable modules for the organization of information on environmental improvement has a long term impact. The information developed can be used and reused in a variety of manufacturing plants and for a range of wind generator sizes and designs. Such a modular approach will lower the cost of life cycle analysis, that is often asked questions of carbon footprint, environmental impact, and sustainability. The use of a website for dissemination, linked to NREL, adds to the economic benefit as more users have access to the lci information. Benefit to the public has been achieved by a well-attended WSU conference, as well as presentations for the Kansas Wind Energy Commission. Attendees represented public interests, land owners, wind farm developers, those interested in green jobs, and industry. Another benefit to the public is the start of information flow from manufacturers that can inform individuals about products.

  2. Assessment of Charging Infrastructure for Plug-in Electric Vehicles at Naval Air Station Whidbey Island: Task 3

    SciTech Connect

    Schey, Steve; Francfort, Jim

    2015-07-01

    Several U.S. Department of Defense base studies have been conducted to identify potential U.S. Department of Defense transportation systems that are strong candidates for introduction or expansion of plug-in electric vehicles (PEVs). Task 1 consisted of a survey of the non-tactical fleet of vehicles at NASWI to begin the review of vehicle mission assignments and types of vehicles in service. Task 2 selected vehicles for further monitoring and involved identifying daily operational characteristics of these select vehicles. Data logging of vehicle movements was initiated in order to characterize the vehicle’s mission. The Task 3 Vehicle Utilization report provided the results of the data analysis and observations related to the replacement of current vehicles with PEVs. This report provides an assessment of charging infrastructure required to support the suggested PEV replacements.

  3. A Study on Developing "An Attitude Scale for Project and Performance Tasks for Turkish Language Leaching Course"

    ERIC Educational Resources Information Center

    Demir, Tazegul

    2013-01-01

    The main purpose of this study is to demonstrate the students' attitudes towards project and performance tasks in Turkish Lessons and to develop a reliable and valid measurement tool. A total of 461 junior high school students participated in this study. In this study, firstly the preparation of items, specialist be consulted (content…

  4. Exploratory Program for Auto Mechanics: Task List and Competency Record. Developed for Vocational-Technical Curriculum Articulation in Minnesota.

    ERIC Educational Resources Information Center

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    Intended for the vocational instructor, the booklet presents a task list and competency record for an exploratory program in auto mechanics. The list was developed by a working committee of auto mechanics instructors and industry representatives throughout the state of Minnesota for use in program articulation between secondary and postsecondary…

  5. Service Center Mechanic: Task List and Competency Record. Developed for Vocational-Technical Curriculum Articulation in Minnesota.

    ERIC Educational Resources Information Center

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    Intended for the vocational instructor, the booklet presents a task list and competency record for the occupational program of service center mechanic. The list was developed by a working committee of auto mechanics instructors and industry representatives throughout the state of Minnesota for use in program articulation between secondary and…

  6. Development of information-movement couplings in a rhythmical ball-bouncing task: from space- to time-related information.

    PubMed

    Bazile, C; Benguigui, N; Siegler, I A

    2016-01-01

    We studied the development of information-movement couplings in a ball-bouncing task with a special interest in how space- and time-related information is used by people of different ages. Participants from four age groups (children aged 7-8, 9-10 and 11-12 years, and adults) performed a virtual ball-bouncing task in which space- and time-related information were independently manipulated. Task performance and information-movement couplings were analyzed. Our results confirm a clear use of time-related information in adults, while children demonstrated a predominant relationship between space-related information and the period of movement. In the course of development, however, the children become progressively more capable of using time-related information in order to control the rhythmic ball-bouncing task. A second and weaker coupling, between ball height information and racket velocity at impact, also appears in the course of development. The data seem to show that the development of children follows the freezing-freeing-exploiting sequence proposed by Savelsbergh and Van der Kamp (Int J Sport Psychol 31:467-484, 2000), with a significant change in how information is used to control movement related to age.

  7. Virtual Task-Based Situated Language-Learning with "Second Life": Developing EFL Pragmatic Writing and Technological Self-Efficacy

    ERIC Educational Resources Information Center

    Abdallah, Mahmoud M. S.; Mansour, Marian M.

    2015-01-01

    This paper reports on an experimental research study that aimed at investigating the effectiveness of employing a virtual task-based situated language learning (TBSLL) environment mediated by Second Life (SL) in developing EFL student teachers' pragmatic writing skills and their technological self-efficacy. To reach this goal, a control-only…

  8. Students' Coordination of Geometric Reasoning and Measuring Strategies on a Fixed Perimeter Task: Developing Mathematical Understanding of Linear Measurement

    ERIC Educational Resources Information Center

    Barrett, Jeffrey E.; Clements, Douglas H.; Klanderman, David; Pennisi, Sarah-Jean; Polaki, Mokaeane V.

    2006-01-01

    This article examines students' development of levels of understanding for measurement by describing the coordination of geometric reasoning with measurement and numerical strategies. In analyzing the reasoning and argumentation of 38 Grade 2 through Grade 10 students on linear measure tasks, we found support for the application and elaboration of…

  9. Occupational Analysis for Human Resource Development: A Review of Utility of the Task Inventory. Research Report No. 25.

    ERIC Educational Resources Information Center

    Moore, Brian E.

    A review of the issues concerning the field of occupational analysis was undertaken in order to indicate the comparative strengths and weaknesses of the task inventory (TI). Specifically, the significance of the TI was assessed for reliability and validity, job analysis and evaluation, occupational restructuring and career ladder development, and…

  10. The Cross-Lagged Relations between Children's Academic Skill Development, Task-Avoidance, and Parental Beliefs about Success

    ERIC Educational Resources Information Center

    Magi, Katrin; Lerkkanen, Marja-Kristiina; Poikkeus, Anna-Maija; Rasku-Puttonen, Helena; Nurmi, Jari-Erik

    2011-01-01

    This longitudinal study investigated the cross-lagged associations between children's academic skill development, task-avoidant behaviour in the context of homework, and parental beliefs about their child's success from kindergarten to Grade 2. The participants were 1267 children. The children's pre-skills were assessed at the end of the…

  11. Developing PISA-"Like" Mathematics Task with Indonesia Natural and Cultural Heritage as Context to Assess Students Mathematical Literacy

    ERIC Educational Resources Information Center

    Oktiningrum, Wuli; Zulkardi; Hartono, Yusuf

    2016-01-01

    The aim of this research is produce a set of PISA-like mathematics task with Indonesia natural and cultural heritage as context which are valid, practical, to assess students' mathematics literacy. This is design research using type of development research with formative evaluation. A total of 20 students of SMP Negeri 1 Palembang. Beside, 10…

  12. Mountains of Work: NACUBO TRA97 Task Force Takes Proactive Stance in Developing Processes, Recommending Changes, and Offering Advice.

    ERIC Educational Resources Information Center

    Gross, Anne C.; Bachinger, Mary M.; Whalen, Edward L.

    1998-01-01

    A National Association of College and University Business Officers (NACUBO) task force has developed a process guide, list of policy issues and unsolved questions, and recommendations for colleges and universities to use in complying with the reporting requirements of the Tax Relief Act of 1997, which provides parents of college students with tax…

  13. In Search of Design Principles for Developing Digital Learning and Performance Support for a Student Design Task

    ERIC Educational Resources Information Center

    Bollen, Lars; van der Meij, Hans; Leemkuil, Henny; McKenney, Susan

    2015-01-01

    A digital learning and performance support environment for university student design tasks was developed. This paper describes on the design rationale, process, and the usage results to arrive at a core set of design principles for the construction of such an environment. We present a collection of organizational, technical, and course-related…

  14. Moving Bed, Granular Bed Filter Development Program: Option 1, Component Test Facility. Task 2, Identification of technical issues

    SciTech Connect

    Haas, J.C.; Wilson, K.B.

    1994-03-01

    Combustion Power, under the auspices of the US Department of Energy, is developing a moving granular-bed filter for the control of particulate in gasification and pressurized fluidized bed environments. In Task 2, technical issues are identified which need to be resolved for the granular-bed filter to be commercially viable. The technical issues are ranked in relative importance.

  15. The Development of Memory Maintenance: Children's Use of Phonological Rehearsal and Attentional Refreshment in Working Memory Tasks

    ERIC Educational Resources Information Center

    Tam, Helen; Jarrold, Christopher; Baddeley, Alan D.; Sabatos-DeVito, Maura

    2010-01-01

    Past research suggests that children begin to phonologically rehearse at around 7 years of age. Less is known regarding the development of refreshment, an attention-based maintenance mechanism. Therefore, the use of these two maintenance methods by 6- and 8-year-olds was assessed using memory span tasks that varied in their opportunities for…

  16. The Development of Hand Preference in Children: The Effect of Task Demands and Links with Manual Dexterity

    ERIC Educational Resources Information Center

    Hill, Elisabeth L.; Khanem, Fateha

    2009-01-01

    Lateralisation of hand preference and manual dexterity are known to develop over childhood, while in adulthood strength of hand preference has been shown to interact with extrinsic task demands. Some evidence exists to suggest that strength of hand preference and motor skill may be related. In the current study a handedness inventory, midline…

  17. Genre-Based Tasks in Foreign Language Writing: Developing Writers' Genre Awareness, Linguistic Knowledge, and Writing Competence

    ERIC Educational Resources Information Center

    Yasuda, Sachiko

    2011-01-01

    This study examines how novice foreign language (FL) writers develop their genre awareness, linguistic knowledge, and writing competence in a genre-based writing course that incorporates email-writing tasks. To define genre, the study draws on systemic functional linguistics (SFL) that sees language as a resource for making meaning in a particular…

  18. The Effect of Form versus Meaning-Focused Tasks on the Development of Collocations among Iranian Intermediate EFL Learners

    ERIC Educational Resources Information Center

    Pishghadam, Reza; Khodadady, Ebrahim; Rad, Naeemeh Daliry

    2011-01-01

    This study attempts comprehensively to investigate the effect of form versus meaning-focused tasks on the development of collocations among Iranian Intermediate EFL learners. To this end, 65 students of Mashhad High schools in Iran were selected as the participants. A general language proficiency test of Nelson (book 2, Intermediate 200A) was used…

  19. The Design and Implementation of Forty Manipulative Tasks to Develop Cooperation in a Kindergarten Class at Palmer School.

    ERIC Educational Resources Information Center

    Schmitz, Dolores J.

    Described in this report are the design and implementation of manipulative tasks developed to decrease the number of aggressive acts among kindergarten children during play time. A total of 17 kindergarten boys and girls randomly selected from three kindergarten classes were observed once a week over a period of 6 weeks by two observers recording…

  20. Resource characterization and residuals remediation, Task 1.0: Air quality assessment and control, Task 2.0: Advanced power systems, Task 3.0: Advanced fuel forms and coproducts, Task 4.0

    SciTech Connect

    Hawthorne, S.B.; Timpe, R.C.; Hartman, J.H.

    1994-02-01

    This report addresses three subtasks related to the Resource Characterization and Residuals Remediation program: (1) sulfur forms in coal and their thermal transformations, (2) data resource evaluation and integration using GIS (Geographic Information Systems), and (3) supplementary research related to the Rocky Mountain 1 (RM1) UCG (Underground Coal Gasification) test program.

  1. CERAMIC MEMBRANE ENABLING TECHNOLOGY FOR IMPROVED IGCC EFFICIENCY

    SciTech Connect

    Ravi Prasad

    2003-11-01

    This quarterly technical progress report will summarize work accomplished for Phase 2 Program during the quarter July to September 2003. In task 1 OTM development has led to improved strength and composite design. In task 2, the manufacture of robust PSO1d elements has been scaled up. In task 3, operational improvements in the lab-scale pilot reactor have reduced turn-around time and increased product purity. In task 7, economic models show substantial benefit of OTM IGCC over CRYO based oxygen production. The objectives of the first year of phase 2 of the program are to construct and operate an engineering pilot reactor for OTM oxygen. Work to support this objective is being undertaken in the following areas in this quarter: Element reliability; Element fabrication; Systems technology; Power recovery; and IGCC process analysis and economics. The major accomplishments this quarter were Element production at Praxair's manufacturing facility is being scaled up and Substantial improvements to the OTM high temperature strength have been made.

  2. Functional Task Test: 3. Skeletal Muscle Performance Adaptations to Space Flight

    NASA Technical Reports Server (NTRS)

    Ryder, Jeffrey W.; Wickwire, P. J.; Buxton, R. E.; Bloomberg, J. J.; Ploutz-Snyder, L.

    2011-01-01

    The functional task test is a multi-disciplinary study investigating how space-flight induced changes to physiological systems impacts functional task performance. Impairment of neuromuscular function would be expected to negatively affect functional performance of crewmembers following exposure to microgravity. This presentation reports the results for muscle performance testing in crewmembers. Functional task performance will be presented in the abstract "Functional Task Test 1: sensory motor adaptations associated with postflight alternations in astronaut functional task performance." METHODS: Muscle performance measures were obtained in crewmembers before and after short-duration space flight aboard the Space Shuttle and long-duration International Space Station (ISS) missions. The battery of muscle performance tests included leg press and bench press measures of isometric force, isotonic power and total work. Knee extension was used for the measurement of central activation and maximal isometric force. Upper and lower body force steadiness control were measured on the bench press and knee extension machine, respectively. Tests were implemented 60 and 30 days before launch, on landing day (Shuttle crew only), and 6, 10 and 30 days after landing. Seven Space Shuttle crew and four ISS crew have completed the muscle performance testing to date. RESULTS: Preliminary results for Space Shuttle crew reveal significant reductions in the leg press performance metrics of maximal isometric force, power and total work on R+0 (p<0.05). Bench press total work was also significantly impaired, although maximal isometric force and power were not significantly affected. No changes were noted for measurements of central activation or force steadiness. Results for ISS crew were not analyzed due to the current small sample size. DISCUSSION: Significant reductions in lower body muscle performance metrics were observed in returning Shuttle crew and these adaptations are likely

  3. Inwardly rectifying Kir3.1 subunit knockdown impairs learning and memory in an olfactory associative task in rat.

    PubMed

    Kourrich, Saïd; Masmejean, Frédérique; Martin-Eauclaire, Marie France; Soumireu-Mourat, Bernard; Mourre, Christiane

    2003-05-12

    Inward-rectifier potassium channels gated by the direct action of G proteins are activated or inhibited by numerous neurotransmitters and they modulate neuronal excitability. Using an olfactory associative task, the effect of Kir3.1 subunit knockdown was tested on learning and memory. Repeated intracerebroventricular injections of antisense oligodeoxyribonucleotide to the Kir3.1 subunit significantly reduced hippocampal expression of its mRNA target determined by Western blotting. The antisense knockdown had no effect on locomotor and drinking activity or on attention processes. The reduction in Kir3.1 subunit impaired the learning of the odor associations and the procedural side of the task. This reduction correlated with the performance impairment. The results suggest that Kir3.1 channel activity is implicated in the memory processes. PMID:12750011

  4. Caspr3-Deficient Mice Exhibit Low Motor Learning during the Early Phase of the Accelerated Rotarod Task

    PubMed Central

    Hirata, Haruna; Takahashi, Aki; Shimoda, Yasushi; Koide, Tsuyoshi

    2016-01-01

    Caspr3 (Contactin-associated protein-like 3, Cntnap3) is a neural cell adhesion molecule belonging to the Caspr family. We have recently shown that Caspr3 is expressed abundantly between the first and second postnatal weeks in the mouse basal ganglia, including the striatum, external segment of the globus pallidus, subthalamic nucleus, and substantia nigra. However, its physiological role remains largely unknown. In this study, we conducted a series of behavioral analyses on Capsr3-knockout (KO) mice and equivalent wild-type (WT) mice to investigate the role of Caspr3 in brain function. No significant differences were observed in most behavioral traits between Caspr3-KO and WT mice, but we found that Caspr3-KO mice performed poorly during the early phase of the accelerated rotarod task in which latency to falling off a rod rotating with increasing velocity was examined. In the late phase, the performance of the Caspr3-KO mice caught up to the level of WT mice, suggesting that the deletion of Caspr3 caused a delay in motor learning. We then examined changes in neural activity after training on the accelerated rotarod by conducting immunohistochemistry using antibody to c-Fos, an indirect marker for neuronal activity. Experience of the accelerated rotarod task caused increases in the number of c-Fos-positive cells in the dorsal striatum, cerebellum, and motor cortex in both Caspr3-KO and WT mice, but the number of c-Fos-positive cells was significantly lower in the dorsal striatum of Caspr3-KO mice than in that of WT mice. The expression of c-Fos in the ventral striatum of Caspr3-KO and WT mice was not altered by the training. Our findings suggest that reduced activation of neural cells in the dorsal striatum in Caspr3-KO mice leads to a decline in motor learning in the accelerated rotarod task. PMID:26807827

  5. The Development of Creativity in Preschoolers' Drawings through Task-Oriented Activities

    ERIC Educational Resources Information Center

    Dulama, Maria Eliza; Iovu, Mihai-Bogdan; Vanea, Cornelia

    2011-01-01

    The goal of this paper is to plan working task for preschool children in order to deliver original and creative outputs. The theoretical background of the paper is set in defining creativity as "the capacity to create something new, original, and adequate to reality" (Roco, 2004; Jaoui, 1975; Rosca, 1981; Boden, 1992). The research…

  6. Evaluating Fifth- and Sixth-Grade Students' Expository Writing: Task Development, Scoring, and Psychometric Issues

    ERIC Educational Resources Information Center

    Kulikowich, Jonna M.; Mason, Linda H.; Brown, Scott W.

    2008-01-01

    Drawing from multiple theoretical frameworks representing cognitive and educational psychology, we present a writing task and scoring system for measurement of students' informative writing. Participants in this study were 72 fifth- and sixth-grade students who wrote compositions describing real-world problems and how mathematics, science, and…

  7. Exploring Ava's Developing Sense for Tasks That May Occasion Mathematical Creativity

    ERIC Educational Resources Information Center

    Levenson, Esther

    2015-01-01

    This study explores the relationship between participating in a graduate course aimed at enhancing teachers' theoretical and practical knowledge of mathematical creativity and one teacher's changing perspectives regarding mathematical creativity and tasks that may occasion mathematical creativity. Results indicated that perceptions of…

  8. Effects of uncontrollability and failure on the development of learned helplessness in perceptual-motor tasks.

    PubMed

    Gernigon, C; Fleurance, P; Reine, B

    2000-03-01

    The aim of this study was to distinguish between the roles of uncontrollability and failure on learned helplessness in a perceptual-motor task. Forty-eight junior high school students were randomly assigned in a 2 x 2 (Controllability: Contingent vs. Yoked Noncontingent Feedback x Type of Outcome: Success vs. Failure) factorial design to complete a gun-shooting task on a moving target using a computer screen. Twelve other participants (control group) simply read a passage. After filling out causal attribution and self-efficacy expectations questionnaires, all participants carried out another gun-shooting task (test task). Results showed that contingency led to higher performances than noncontingency. Success conditions elicited higher self-efficacy expectations than failure conditions. Failure entailed less persistence than success did for participants who had been assigned to the contingency condition. Internalization of failure was negatively correlated with persistence. Comparisons with the control group showed that expectations and performance deficits of learned helplessness were provoked by failure in noncontingent situations; persistence deficits were due to failure in contingent situations. These results reveal that both uncontrollability and failure can be responsible for different forms of learned helplessness. PMID:10763520

  9. Implementation of a Performance Task for Developing the Value of Love of Nature

    ERIC Educational Resources Information Center

    Aktepe, Vedat

    2015-01-01

    The purpose of this study is to determine the effects of the love of nature performance task on the opinions and attitudes of 4th grade primary school students at the Science and Art center towards their value of love of nature. The mixed method was used by means of both quantitative and qualitative research models. The experimental group…

  10. Task Force on Undergraduate Curricula Development. Report. Academic Programs Publication Series Number 13.

    ERIC Educational Resources Information Center

    Florida Univ., Gainesville. Inst. of Food and Agricultural Sciences.

    A task force studied the undergraduate program at the College of Agriculture and the School of Forest Resources and Conservation at the University of Florida, ranging from recruitment techniques and strategies designed to attract students to the college to strategies to recognize and reward quality teaching at the undergraduate level. Data were…

  11. The Role of Multiple Solution Tasks in Developing Knowledge and Creativity in Geometry

    ERIC Educational Resources Information Center

    Levav-Waynberg, Anat; Leikin, Roza

    2012-01-01

    This paper describes changes in students' geometrical knowledge and their creativity associated with implementation of Multiple Solution Tasks (MSTs) in school geometry courses. Three hundred and three students from 14 geometry classes participated in the study, of whom 229 students from 11 classes learned in an experimental environment that…

  12. Choosing High-Yield Tasks for the Mathematical Development of Practicing Secondary Teachers

    ERIC Educational Resources Information Center

    Epperson, James A. Mendoza; Rhoads, Kathryn

    2015-01-01

    Many mathematics teacher educators encounter the challenge of creating or choosing mathematical tasks that evoke important mathematical insights and connections yet remain firmly grounded in school mathematics. This challenge increases substantially when trying to meet the needs of practicing secondary mathematics teachers pursuing graduate work…

  13. National facilities study. Volume 2: Task group on aeronautical research and development facilities report

    NASA Technical Reports Server (NTRS)

    1994-01-01

    The Task Group on Aeronautics R&D Facilities examined the status and requirements for aeronautics facilities against the competitive need. Emphasis was placed on ground-based facilities for subsonic, supersonic and hypersonic aerodynamics, and propulsion. Subsonic and transonic wind tunnels were judged to be most critical and of highest priority. Results of the study are presented.

  14. Am/Cm TTR testing -- 3/8-inch glass beads evaluation in CIM5[Technical Task Request

    SciTech Connect

    Witt, D. C.

    2000-01-20

    To facilitate the procurement and handling of the glass former for Am/Cm vitrification in the F-Canyon MPPF, 1/4 inch and 3/8 inch diameter glass beads were purchased from Corning for evaluation in the 5 inch Cylindrical Induction Melter (CIM5). Prior to evaluating the beads in the CIM5, tests were conducted in the Drain Tube Test Stand (DTTS) with 1/4 inch beads, 3/8 inch beads, and a 50/50 mixture to identify any process concerns. Results of the DTTS tests are summarized in Attachment 1. A somewhat larger volume expansion was experienced in all three DTTS runs as compared to a standard run using cullet. Further testing of the use of glass beads in the CIM5 was requested by the Design Authority as Task 1.02 of Technical Task Request 99-MNSS/SE-006. Since the Technical Task Plan was not yet approved, the completion of this task was conducted under an authorization request approved by the SRTC Laboratory Director, S. Wood. This request is included as Attachment 2.

  15. Age-related trends of inhibitory control in Stroop-like big-small task in 3 to 12-year-old children and young adults.

    PubMed

    Ikeda, Yoshifumi; Okuzumi, Hideyuki; Kokubun, Mitsuru

    2014-01-01

    Inhibitory control is the ability to suppress competing, dominant, automatic, or prepotent cognitive processing at perceptual, intermediate, and output stages. Inhibitory control is a key cognitive function of typical and atypical child development. This study examined age-related trends of Stroop-like interference in 3 to 12-year-old children and young adults by administration of a computerized Stroop-like big-small task with reduced working memory demand. This task used a set of pictures displaying a big and small circle in black and included the same condition and the opposite condition. In the same condition, each participant was instructed to say "big" when viewing the big circle and to say "small" when viewing the small circle. In the opposite condition, each participant was instructed to say "small" when viewing the big circle and to say "big" when viewing the small circle. The opposite condition required participants to inhibit the prepotent response of saying the same, a familiar response to a perceptual stimulus. The results of this study showed that Stroop-like interference decreased markedly in children in terms of error rates and correct response time. There was no deterioration of performance occurring between the early trials and the late trials in the sessions of the day-night task. Moreover, pretest failure rate was relatively low in this study. The Stroop-like big-small task is a useful tool to assess the development of inhibitory control in young children in that the task is easy to understand and has small working memory demand.

  16. Changes in P3b Latency and Amplitude Reflect Expertise Acquisition in a Football Visuomotor Learning Task

    PubMed Central

    Morgan, Kyle K.; Luu, Phan; Tucker, Don M.

    2016-01-01

    Learning is not a unitary phenomenon. Rather, learning progresses through stages, with the stages reflecting different challenges that require the support of specific cognitive processes that reflect the functions of different brain networks. A theory of general learning proposes that learning can be divided into early and late stages controlled by corticolimbic networks located in frontal and posterior brain regions, respectively. Recent human studies using dense-array EEG (dEEG) support these results by showing progressive increases in P3b amplitude (an Event Related Potential with estimated sources in posterior cingulate cortex and hippocampus) as participants acquire a new visuomotor skill. In the present study, the P3b was used to track the learning and performance of participants as they identify defensive football formations and make an appropriate response. Participants acquired the task over three days, and P3b latency and amplitude significantly changed when participants learned the task. As participants demonstrated further proficiency with extensive training, amplitude and latency changes in the P3b continued to closely mirror performance improvements. Source localization results across all days suggest that an important source generator of the P3b is located in the posterior cingulate cortex. Results from the study support prior findings and further suggest that the careful analysis of covert learning mechanisms and their underlying electrical signatures are a robust index of task competency. PMID:27111898

  17. ZERO EMISSION POWER PLANTS USING SOLID OXIDE FUEL CELLS AND OXYGEN TRANSPORT MEMBRANES

    SciTech Connect

    G. Maxwell Christie; Troy M. Raybold

    2003-06-10

    Over 16,700 hours of operational experience was gained for the Oxygen Transport Membrane (OTM) elements of the proposed SOFC/OTM zero-emission power generation concept. It was repeatedly demonstrated that OTMs with no additional oxidation catalysts were able to completely oxidize the remaining depleted fuel in a simulated SOFC anode exhaust at an O{sub 2} flux that met initial targets. In such cases, neither residual CO nor H{sub 2} were detected to the limits of the gas chromatograph (<10 ppm). Dried OTM afterburner exhaust streams contained up to 99.5% CO{sub 2}. Oxygen flux through modified OTMs was double or even triple that of the standard OTMs used for the majority of testing purposes. Both the standard and modified membranes in laboratory-scale and demonstration-sized formats exhibited stable performance over extended periods (2300 to 3500 hours or 3 to 5 months). Reactor contaminants, were determined to negatively impact OTM performance stability. A method of preventing OTM performance degradation was developed and proven to be effective. Information concerning OTM and seal reliability over extended periods and through various chemical and thermal shocks and cycles was also obtained. These findings were used to develop several conceptual designs for pilot (10 kWe) and commercial-scale (250 kWe) SOFC/OTM zero emission power generation systems.

  18. Targeting two-pore domain K+ channels TREK-1 and TASK-3 for the treatment of depression: a new therapeutic concept

    PubMed Central

    Borsotto, M; Veyssiere, J; Moha ou Maati, H; Devader, C; Mazella, J; Heurteaux, C

    2015-01-01

    Depression is a disease that is particularly frequent, affecting up to 20% of the population in Western countries. The origins of this pathology involve multiple genes as well as environmental and developmental factors leading to a disorder that remains difficult to treat. Several therapies for depression have been developed and these mainly target monoamine neurotransmitters. However, these treatments are not only associated with numerous adverse effects, but they are also ineffective for more than one-third of patients. Therefore, the need to develop new concepts to treat depression is crucial. Recently, studies using knockout mouse models have provided evidence for a crucial role of two members of the two-pore domain potassium channel (K2P) family, tandem P-domain weak inward rectifying K+ (TWIK)-related K+ channel 1 (TREK-1) and TWIK-related acid-sensitive K+ channel 3 (TASK-3) in the pathophysiology of depression. It is believed that TREK-1 and TASK-3 antagonists could lead to the development of new antidepressants. Herein, we describe the discovery of spadin, a natural peptide released from the maturation of the neurotensin receptor-3 (also known as sortilin), which specifically blocks the activity of the TREK-1 channel and displays particular antidepressant properties, with a rapid onset of action and the absence of adverse effects. The development of such molecules may open a new era in the field of psychiatry. PMID:25263033

  19. LNG Safety Research: FEM3A Model Development

    SciTech Connect

    Liese Dallbauman

    2004-06-30

    During this reporting period, kickoff and planning meetings were held. Subcontracted experimental and modeling tasks were defined. Efforts to address the numerical stability problems that hamper FEM3A's applicability to low wind speed, stable atmospheric conditions were initiated. A detailed review of FEM3A code and its execution, required for development of an accessible user interface, was also begun. A one-day workshop on LNG safety models has been scheduled for September 2004. The goals of this project are to develop a national focal point for LNG safety research and technical dissemination and to develop the FEM3A dispersion model for application to general scenarios involving dispersion problems with obstacle and terrain features of realistic complexity. During this reporting period, the objectives and scope of the project and its constituent tasks were discussed at a project kickoff meeting in Morgantown. Details of the subcontracted experimental and modeling tasks were further defined at a separate meeting at the University of Arkansas. Researchers at the university have begun to modify the turbulence closure model used in FEM3A to insure numerical stability during simulation of low-wind-speed, stable atmospheric conditions. The university's wind tunnel is being prepared for upcoming experimental studies. GTI has begun a detailed review of the FEM3A code and its execution that will provide guidance during development of an accessible user interface. Plans were made for a one day workshop on LNG safety models that will be held at the end of September and will provide an introduction to currently available and pending software tools.

  20. Development of calibration training and procedures using job-task analysis

    SciTech Connect

    Smith, R.A.

    1993-12-01

    Efforts to handle an increased workload with dwindling manpower in the Physical and Electrical Standards Laboratory (Standards Lab) at the Oak Ridge Y-12 Plant are described. Empowerment of workers via Total Quality Management (TQM) is the basis for their efforts. A survey and follow-up team work was the course of action. The job-task analysis received honors by their peers at the Y-12 Plant.

  1. The Impact of Selective Dopamine D2, D3 and D4 Ligands on the Rat Gambling Task

    PubMed Central

    Kim, Aaron; Hatch, Jessica; Masood, Talal; Ramzi, Abby; Khaled, Maram A. T. M.; Boileau, Isabelle; Winstanley, Catherine A.; Le Foll, Bernard

    2015-01-01

    Gambling is an addictive disorder with serious societal and personal costs. To-date, there are no approved pharmacological treatments for gambling disorder. Evidence suggests a role for dopamine in gambling disorder and thus may provide a therapeutic target. The present study therefore aimed to investigate the effects of selective antagonists and agonists of D2, D3 and D4 receptors in a rodent analogue of the Iowa gambling task used clinically. In this rat gambling task (rGT), animals are trained to associate different response holes with different magnitudes and probabilities of food pellet rewards and punishing time-out periods. As in the Iowa gambling task, the optimal strategy is to avoid the tempting high-risk high-reward options, and instead favor those linked to smaller per-trial rewards but also lower punishments, thereby maximizing the amount of reward earned over time. Administration of those selective ligands did not affect decision making under the rGT. Only the D4 drug had modest effects on latency measures suggesting that D4 may contribute in some ways to decision making under this task. PMID:26352802

  2. The Impact of Selective Dopamine D2, D3 and D4 Ligands on the Rat Gambling Task.

    PubMed

    Di Ciano, Patricia; Pushparaj, Abhiram; Kim, Aaron; Hatch, Jessica; Masood, Talal; Ramzi, Abby; Khaled, Maram A T M; Boileau, Isabelle; Winstanley, Catherine A; Le Foll, Bernard

    2015-01-01

    Gambling is an addictive disorder with serious societal and personal costs. To-date, there are no approved pharmacological treatments for gambling disorder. Evidence suggests a role for dopamine in gambling disorder and thus may provide a therapeutic target. The present study therefore aimed to investigate the effects of selective antagonists and agonists of D2, D3 and D4 receptors in a rodent analogue of the Iowa gambling task used clinically. In this rat gambling task (rGT), animals are trained to associate different response holes with different magnitudes and probabilities of food pellet rewards and punishing time-out periods. As in the Iowa gambling task, the optimal strategy is to avoid the tempting high-risk high-reward options, and instead favor those linked to smaller per-trial rewards but also lower punishments, thereby maximizing the amount of reward earned over time. Administration of those selective ligands did not affect decision making under the rGT. Only the D4 drug had modest effects on latency measures suggesting that D4 may contribute in some ways to decision making under this task. PMID:26352802

  3. The Impact of Selective Dopamine D2, D3 and D4 Ligands on the Rat Gambling Task.

    PubMed

    Di Ciano, Patricia; Pushparaj, Abhiram; Kim, Aaron; Hatch, Jessica; Masood, Talal; Ramzi, Abby; Khaled, Maram A T M; Boileau, Isabelle; Winstanley, Catherine A; Le Foll, Bernard

    2015-01-01

    Gambling is an addictive disorder with serious societal and personal costs. To-date, there are no approved pharmacological treatments for gambling disorder. Evidence suggests a role for dopamine in gambling disorder and thus may provide a therapeutic target. The present study therefore aimed to investigate the effects of selective antagonists and agonists of D2, D3 and D4 receptors in a rodent analogue of the Iowa gambling task used clinically. In this rat gambling task (rGT), animals are trained to associate different response holes with different magnitudes and probabilities of food pellet rewards and punishing time-out periods. As in the Iowa gambling task, the optimal strategy is to avoid the tempting high-risk high-reward options, and instead favor those linked to smaller per-trial rewards but also lower punishments, thereby maximizing the amount of reward earned over time. Administration of those selective ligands did not affect decision making under the rGT. Only the D4 drug had modest effects on latency measures suggesting that D4 may contribute in some ways to decision making under this task.

  4. Advanced Diesel Engine Component Development Program, final report - tasks 4-14

    SciTech Connect

    Kaushal, T.S.; Weber, K.E.

    1994-11-01

    The Advanced Diesel Engine Component Development (ADECD) Program is a multi-year, multi-phase effort to develop and demonstrate the critical technology needed to advance the heavy-duty low heat rejection (LHR) engine concept for the long-haul, heavy-duty truck market. The ADECD Program has been partitioned into two phases. The first phase, Phase 1, was completed in 1986, resulting in definition of the Advanced Diesel Reference Engine (ADRE)III. The second phase, Phase 11/111, examines the feasibility of the ADRE concepts for application to the on-highway diesel engine. Phase 11/111 is currently underway. This project is sponsored by the U.S. Department of Energy, Office of Transportation Technologies. The work has been performed by the Detroit Diesel Corporation (DDC) under Contract DEN3-329 with the NASA Lewis Research Center, who provide project management and technical direction.

  5. Multiple pollutant removal using the condensing heat exchanger. Task 3, Long term testing at the ECTC

    SciTech Connect

    Schulze, K.H.

    1996-01-01

    The objective of this task is to demonstrate long term operation of a condensing heat exchanger for coal-fired conditions. A small condensing heat exchanger will be installed at the Environmental Control Technology Center in Barker, New York. It will be installed downstream of the flue gas particulate removal system. The test will determine the amount of wear, if any, on the Teflon{trademark} covered internals of the heat exchanger. Visual inspection and measurements will be obtained for the Teflon{trademark} covered tubes during the test. The material wear study will conducted over a one year calendar period, and the CHX equipment will be operated to the fullest extent allowable.

  6. Chapter 3: Develop a Vision

    PubMed Central

    Jones, Loretta; Meade, Barbara; Norris, Keith; Lucas-Wright, Aziza; Jones, Felica; Moini, Moraya; Jones, Andrea; Koegel, Paul

    2016-01-01

    The Vision stage is the development of the agreed-upon framework for the study, including identifying the issue, the community, the stakeholders, and major aspects of the approach. Achieving the Vision requires planning through a Framing Committee, agreeing on a vision by sharing perspectives and identifying commonalities or “win-wins” that hold the partnership together for community benefit, and evaluating the emergence of the Vision and the partnership. Here, we review tools and strategies. PMID:20088078

  7. Neurotensinergic Excitation of Dentate Gyrus Granule Cells via Gαq-Coupled Inhibition of TASK-3 Channels.

    PubMed

    Zhang, Haopeng; Dong, Hailong; Cilz, Nicholas I; Kurada, Lalitha; Hu, Binqi; Wada, Etsuko; Bayliss, Douglas A; Porter, James E; Lei, Saobo

    2016-03-01

    Neurotensin (NT) is a 13-amino acid peptide and serves as a neuromodulator in the brain. Whereas NT has been implicated in learning and memory, the underlying cellular and molecular mechanisms are ill-defined. Because the dentate gyrus receives profound innervation of fibers containing NT and expresses high density of NT receptors, we examined the effects of NT on the excitability of dentate gyrus granule cells (GCs). Our results showed that NT concentration dependently increased action potential (AP) firing frequency of the GCs by the activation of NTS1 receptors resulting in the depolarization of the GCs. NT-induced enhancement of AP firing frequency was not caused indirectly by releasing glutamate, GABA, acetylcholine, or dopamine, but due to the inhibition of TASK-3 K(+) channels. NT-mediated excitation of the GCs was G protein dependent, but independent of phospholipase C, intracellular Ca(2+) release, and protein kinase C. Immunoprecipitation experiment demonstrates that the activation of NTS1 receptors induced the association of Gαq/11 and TASK-3 channels suggesting a direct coupling of Gαq/11 to TASK-3 channels. Endogenously released NT facilitated the excitability of the GCs contributing to the induction of long-term potentiation at the perforant path-GC synapses. Our results provide a cellular mechanism that helps to explain the roles of NT in learning and memory. PMID:25405940

  8. Task report No. 3. Systems analysis of organic Rankine bottoming cycles. [Fuel cell power plant

    SciTech Connect

    Bloomfield, D.; Fried, S.

    1980-12-01

    A model was developed that predicts the design performance and cost of a Fuel Cell/Rankine cycle powerplant. The Rankine cycle utilizes the rejected heat of an 11.3 MW phosphoric acid fuel cell powerplant. Improvements in the total plant heat rate and efficiency of up to 10% were attainalbe, using ammonia as the working fluid. The increase in total plant cost divided by the increase in total plant power ranged from $296/kW to $1069/kW for the cases run, and was a strong function of ambient temperature. The concept appears to be capable of producing substantial energy savings in large fuel cell powerplants, at reasonable costs. However, a much more detailed study that includes such factors as duty cycle, future cost of fuel and site meteorology needs to be done to prove the design for any potential site.

  9. Task report no. 3. Systems analysis of organic Rankine bottoming cycles

    NASA Astrophysics Data System (ADS)

    Bloomfield, D.; Fried, S.

    1980-12-01

    A model was developed that predicts the design performance and cost of a Fuel Cell/Rankine cycle powerplant. The Rankine cycle utilizes the rejected heat of an 11.3 MW phosphoric acid fuel cell powerplant. Improvements in the total plant heat rate and efficiency of up to 10% were attainable, using ammonia as the working fluid. The increase in total plant cost divided by the increase in total plant power ranged from $296/kW to $1069/kW for the cases run, and was a strong function of ambient temperature. The concept appears to be capable of producing substantial energy savings in large fuel cell powerplants, at reasonable costs. However, a much more detailed study that includes such factors as duty cycle, future cost of fuel and site meteorology needs to be done to prove the design for any potential site.

  10. Coolant side heat transfer with rotation. Task 3 report: Application of computational fluid dynamics

    NASA Technical Reports Server (NTRS)

    Kopper, F. C.; Sturgess, G. J.; Datta, P.

    1989-01-01

    An experimental and analytical program was conducted to investigate heat transfer and pressure losses in rotating multipass passages with configurations and dimensions typical of modern turbine blades. The objective of this program is the development and verification of improved analysis methods that will form the basis for a design system that will produce turbine components with improved durability. As part of this overall program, a technique is developed for computational fluid dynamics. The specific objectives were to: select a baseline CFD computer code, assess the limitations of the baseline code, modify the baseline code for rotational effects, verify the modified code against benchmark experiments in the literature, and to identify shortcomings in the code as revealed by the verification. The Pratt and Whitney 3D-TEACH CFD code was selected as the vehicle for this program. The code was modified to account for rotating internal flows, and these modifications were evaluated for flow characteristics of those expected in the application. Results can make a useful contribution to blade internal cooling.

  11. Development of 3D electromagnetic modeling tools for airborne vehicles

    NASA Technical Reports Server (NTRS)

    Volakis, John L.

    1992-01-01

    The main goal of this project is to develop methodologies for scattering by airborne composite vehicles. Although our primary focus continues to be the development of a general purpose code for analyzing the entire structure as a single unit, a number of other tasks are also pursued in parallel with this effort. These tasks are important in testing the overall approach and in developing suitable models for materials coatings, junctions and, more generally, in assessing the effectiveness of the various parts comprising the final code. Here, we briefly discuss our progress on the five different tasks which were pursued during this period. Our progress on each of these tasks is described in the detailed reports (listed at the end of this report) and the memoranda included. The first task described below is, of course, the core of this project and deals with the development of the overall code. Undoubtedly, it is the outcome of the research which was funded by NASA-Ames and the Navy over the past three years. During this year we developed the first finite element code for scattering by structures of arbitrary shape and composition. The code employs a new absorbing boundary condition which allows termination of the finite element mesh only 0.3 lambda from the outer surface of the target. This leads to a remarkable reduction of the mesh size and is a unique feature of the code. Other unique features of this code include capabilities to model resistive sheets, impedance sheets and anisotropic materials. This last capability is the latest feature of the code and is still under development. The code has been extensively validated for a number of composite geometries and some examples are given. The validation of the code is still in progress for anisotropic and larger non-metallic geometries and cavities. The developed finite element code is based on a Galerkin's formulation and employs edge-based tetrahedral elements for discretizing the dielectric sections and the region

  12. Export support of renewable energy industries. Task number 1, deliverable number 3. Final report

    SciTech Connect

    1998-01-14

    The United States Export Council for Renewable Energy (US/ECRE), a consortium of six industry associations, promotes the interests of the renewable energy and energy efficiency member companies which provide goods and services in biomass, geothermal, hydropower, passive solar, photovoltaics, solar thermal, wind, wood energy, and energy efficiency technologies. US/ECRE`s mission is to catalyze export markets for renewable energy and energy efficiency technologies worldwide. Under this grant, US/ECRE has conducted a number of in-house activities, as well as to manage activities by member trade associations, affiliate organizations and non-member contractors and consultants. The purpose of this document is to report on task coordination and effectiveness.

  13. Parametric study of potential early commercial MHD power plants. Task 3: Parameter variation of plant size

    NASA Technical Reports Server (NTRS)

    Hals, F. A.

    1981-01-01

    Plants with a nominal output of 200 and 500 MWe and conforming to the same design configuration as the Task II plant were investigated. This information is intended to permit an assessment of the competitiveness of first generation MHD/steam plants with conventional steam plants over the range of 200 to 1000 MWe. The results show that net plant efficiency of the MHD plant is significantly higher than a conventional steam plant of corresponding size. The cost of electricity is also less for the MHD plant over the entire plant size range. As expected, the cost differential is higher for the larger plant and decreases with plant size. Even at the 200 MWe capacity, however, the differential in COE between the MHD plant and the conventional plant is sufficient attractive to warrant serious consideration. Escalating fuel costs will enhance the competitive position of MHD plants because they can utilize the fuel more efficiently than conventional steam plants.

  14. Waste Tank Safety Program. Annual status report for FY 1993, Task 3: Organic chemistry

    SciTech Connect

    Lucke, R.B.; Clauss, T.T.W.; Hoheimer, R.; Goheen, S.C.

    1994-02-01

    This task supports the tank-vapor project, mainly by providing organic analytical support and by analyzing Tank 241-C-103 (Tank C-103) vapor-space samples, collected via SUMMA{trademark} canisters, by gas chromatography (GC) and GC/mass spectrometry (MS). In the absence of receiving tank-vapor samples, we have focused our efforts toward validating the normal paraffin hydrocarbon (NPH) sampling and analysis methods and preparing the SUMMA{trademark} laboratory. All required milestones were met, including a report on the update of phase I sampling and analysis on August 15, 1993. This update described the work involved in preparing to analyze phase I samples (Appendix A). This report describes the analytical support provided by Pacific Northwest Laboratory (PNL){sup (a)} to the Hanford Tank Safety Vapor Program.

  15. Research and development of a high efficiency gas-fired water heater. Volume 2. Task reports

    SciTech Connect

    Vasilakis, A.D.; Pearson, J.F.; Gerstmann, J.

    1980-01-01

    Design and development of a cost-effective high efficiency gas-fired water heater to attain a service efficiency of 70% (including the effect of exfiltration) and a service efficiency of 78% (excluding exfiltration) for a 75 GPD draw at a 90/sup 0/F temperature rise, with a stored water to conditioned air temperature difference of 80/sup 0/F, are described in detail. Based on concept evaluation, a non-powered natural draft water heater was chosen as the most cost-effective design to develop. The projected installed cost is $374 compared to $200 for a conventional unit. When the project water heater is compared to a conventional unit, it has a payback of 3.7 years and life cycle savings of $350 to the consumer. A prototype water heater was designed, constructed, and tested. When operated with sealed combustion, the unit has a service efficiency of 66.4% (including the effect of exfiltration) below a burner input of 32,000 Btu/h. In the open combustion configuration, the unit operated at a measured efficiency of 66.4% Btu/h (excluding exfiltration). This compares with a service efficiency of 51.3% for a conventional water heater and 61% for a conventional high efficiency unit capable of meeting ASHRAE 90-75. Operational tests showed the unit performed well with no evidence of stacking or hot spots. It met or exceeded all capacity or usage tests specified in the program test plan and met all emission goals. Future work will concentrate on designing, building, and testing pre-production units. It is anticipated that both sealed combustion and open draft models will be pursued.

  16. The ATO (Air Tasking Order): Improving JTLS' (Joint Theater Level Simulation) C/sup 3/I with an expert system

    SciTech Connect

    Hartley, D.; Allgood, G.

    1988-01-01

    The Air Tasking Order (ATO) Advisor models the human cognitive functions (Command, Control, Communications, and Intelligence (C/sup 3/I)) required for interaction with the Joint Theater Level Simulation (JTLS) at the theater level (rather than the air mission level). The ATO Advisor applies specifically to the air war portion of the simulation. It contains an expert system, a decision support system, and a group of fast running LISP and C service routines. Beyond the needs of JTLS, the ATO Advisor provides a paradigm for future C/sup 3/I modeling. 5 figs.

  17. Advanced power assessment for Czech lignite. Task 3.6, Volume 1

    SciTech Connect

    Sondreal, E.A.; Mann, M.D.; Weber, G.W.; Young, B.C.

    1995-12-01

    The US has invested heavily in research, development, and demonstration of efficient and environmentally acceptable technologies for the use of coal. The US has the opportunity to use its leadership position to market a range of advanced coal-based technologies internationally. For example, coal mining output in the Czech Republic has been decreasing. This decrease in demand can be attributed mainly to the changing structure of the Czech economy and to environmental constraints. The continued production of energy from indigenous brown coals is a major concern for the Czech Republic. The strong desire to continue to use this resource is a challenge. The Energy and Environmental Research Center undertook two major efforts recently. One effort involved an assessment of opportunities for commercialization of US coal technologies in the Czech Republic. This report is the result of that effort. The technology assessment focused on the utilization of Czech brown coals. These coals are high in ash and sulfur, and the information presented in this report focuses on the utilization of these brown coals in an economically and environmentally friendly manner. Sections 3--5 present options for utilizing the as-mined coal, while Sections 6 and 7 present options for upgrading and generating alternative uses for the lignite. Contents include Czech Republic national energy perspectives; powering; emissions control; advanced power generation systems; assessment of lignite-upgrading technologies; and alternative markets for lignite.

  18. QUEST/Ada (Query Utility Environment for Software Testing of Ada): The development of a prgram analysis environment for Ada, task 1, phase 2

    NASA Technical Reports Server (NTRS)

    Brown, David B.

    1990-01-01

    The results of research and development efforts are described for Task one, Phase two of a general project entitled The Development of a Program Analysis Environment for Ada. The scope of this task includes the design and development of a prototype system for testing Ada software modules at the unit level. The system is called Query Utility Environment for Software Testing of Ada (QUEST/Ada). The prototype for condition coverage provides a platform that implements expert system interaction with program testing. The expert system can modify data in the instrument source code in order to achieve coverage goals. Given this initial prototype, it is possible to evaluate the rule base in order to develop improved rules for test case generation. The goals of Phase two are the following: (1) to continue to develop and improve the current user interface to support the other goals of this research effort (i.e., those related to improved testing efficiency and increased code reliable); (2) to develop and empirically evaluate a succession of alternative rule bases for the test case generator such that the expert system achieves coverage in a more efficient manner; and (3) to extend the concepts of the current test environment to address the issues of Ada concurrency.

  19. Word retrieval ability on semantic fluency task in typically developing Malayalam-speaking children.

    PubMed

    John, Sunila; Rajashekhar, Bellur

    2014-03-01

    Word-retrieval abilities in children can be assessed using word generation or verbal fluency task. The ability to retrieve is related to the individual's ability to retrieve associated words from the mental lexicon in an organized manner. The present study focuses on the developmental aspects of semantic fluency in 1,015 Malayalam-speaking children in the age range of 5 years to 15 years across both genders. The study revealed a developmental trend in the mean total number of correct word scores, number of clusters generated, and switching scores; however, mean cluster size did not show any statistically significant variation. Further, the scores did not vary across genders. Overall, the study indicated a linear developmental trend during verbal fluency with the increase in complexity of strategy use. PMID:23320414

  20. Task 6 -- Advanced turbine systems program conceptual design and product development

    SciTech Connect

    1996-01-10

    The Allison Engine Company has completed the Task 6 Conceptual Design and Analysis of Phase 2 of the Advanced Turbine System (ATS) contract. At the heart of Allison`s system is an advanced simple cycle gas turbine engine. This engine will incorporate components that ensure the program goals are met. Allison plans to commercialize the ATS demonstrator and market a family of engines incorporating this technology. This family of engines, ranging from 4.9 MW to 12 MW, will be suitable for use in all industrial engine applications, including electric power generation, mechanical drive, and marine propulsion. In the field of electric power generation, the engines will be used for base load, standby, cogeneration, and distributed generation applications.

  1. 78 FR 7849 - Interagency Task Force on Veterans Small Business Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-02-04

    ... efforts of Federal agencies to improve capital, business development opportunities and pre-established... activities and develop proposals relating to ``six focus areas'': (1) Access to capital (loans, surety... development and entrepreneurship opportunities; (5) Increasing and improving training and counseling...

  2. 76 FR 56863 - Interagency Task Force on Veterans Small Business Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-14

    ... coordinating the efforts of Federal agencies to improve capital, business development opportunities and pre... regulatory activities and develop proposals relating to ``six focus areas'': (1) Access to capital (loans... business development and entrepreneurship opportunities; (5) Increasing and improving training...

  3. 77 FR 22056 - Interagency Task Force on Veterans Small Business Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-12

    ... efforts of Federal agencies to improve capital, business development opportunities, and pre-established... activities and develop proposals relating to ``six focus areas'': (1) Access to capital (loans, surety... development and entrepreneurship opportunities; (5) Increasing and improving training and counseling...

  4. 76 FR 8393 - Interagency Task Force on Veterans Small Business Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-02-14

    ... coordinating the efforts of Federal agencies to improve capital, business development opportunities and pre... regulatory activities and develop proposals relating to ``six focus areas'': (1) Access to capital (loans... business development and entrepreneurship opportunities; (5) Increasing and improving training...

  5. 77 FR 41472 - Interagency Task Force on Veterans Small Business Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-13

    ... efforts of Federal agencies to improve capital, business development opportunities and pre-established... activities and develop proposals relating to ``six focus areas'': (1) Access to capital (loans, surety... development and entrepreneurship opportunities; (5) Increasing and improving training and counseling...

  6. 77 FR 1548 - Interagency Task Force on Veterans Small Business Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-10

    ... coordinating the efforts of Federal agencies to improve capital, business development opportunities and pre... regulatory activities and develop proposals relating to ``six focus areas'': (1) Access to capital (loans... business development and entrepreneurship opportunities; (5) Increasing and improving training...

  7. 75 FR 62611 - Interagency Task Force on Veterans Small Business Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-12

    ... coordinating the efforts of Federal agencies to improve capital, business development opportunities and... regulatory activities and develop proposals relating to ``six focus areas'': (1) Access to capital (loans... business development and entrepreneurship opportunities; (5) increasing and improving training...

  8. 76 FR 21090 - Interagency Task Force on Veterans Small Business Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-14

    ... efforts of Federal agencies to improve capital, business development opportunities and pre-established... activities and develop proposals relating to ``six focus areas'': (1) Access to capital (loans, surety... development and entrepreneurship opportunities; (5) Increasing and improving training and counseling...

  9. 75 FR 62438 - Interagency Task Force on Veterans Small Business Development Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-08

    ... coordinating the efforts of Federal agencies to improve capital, business development opportunities and pre... regulatory activities and develop proposals relating to ``six focus areas'': (1) Access to capital (loans... business development and entrepreneurship opportunities; (5) Increasing and improving training...

  10. 75 FR 75187 - Interagency Task Force on Veterans Small Business Development Meeting Notice

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-02

    ... coordinating the efforts of Federal agencies to improve capital, business development opportunities and pre... regulatory activities and develop proposals relating to ``six focus areas'': (1) Access to capital (loans... business development and entrepreneurship opportunities; (5) Increasing and improving training...

  11. Assessment of Charging Infrastructure for Plug-in Electric Vehicles at Marine Corps Base Camp Lejeune. Task 3

    SciTech Connect

    Schey, Stephen; Francfort, Jim

    2015-11-01

    Battelle Energy Alliance, LLC, managing and operating contractor for the U.S. Department of Energy’s Idaho National Laboratory, is the lead laboratory for the U.S. Department of Energy’s advanced vehicle testing. Battelle Energy Alliance, LLC contracted with Intertek Testing Services, North America (Intertek) to conduct several U.S. Department of Defense-based studies to identify potential U.S. Department of Defense transportation systems that are strong candidates for introduction or expansion of plug-in electric vehicles (PEVs). Task 1 consisted of a survey of the non-tactical fleet of vehicles at Marine Corps Base Camp Lejeune to begin the review of vehicle mission assignments and types of vehicles in service. Task 2 selected vehicles for further monitoring and involved identifying daily operational characteristics of these select vehicles. Data logging of vehicle movements was initiated in order to characterize the vehicle’s mission. The Task 3 vehicle utilization report provided results of the data analysis and observations related to the replacement of current vehicles with PEVs. Finally, this report provides an assessment of charging infrastructure required to support the suggested PEV replacements. Intertek acknowledges the support of Idaho National Laboratory, Marine Corps headquarters, and Marine Corps Base Camp Lejeune Fleet management and personnel for participation in this study. Intertek is pleased to provide this report and is encouraged by enthusiasm and support from Marine Corps Base Camp Lejeune personnel.

  12. The First Development of Human Factors Engineering Requirements for Application to Ground Task Design for a NASA Flight Program

    NASA Technical Reports Server (NTRS)

    Dischinger, H. Charles, Jr.; Stambolian, Damon B.; Miller, Darcy H.

    2008-01-01

    The National Aeronautics and Space Administration has long applied standards-derived human engineering requirements to the development of hardware and software for use by astronauts while in flight. The most important source of these requirements has been NASA-STD-3000. While there have been several ground systems human engineering requirements documents, none has been applicable to the flight system as handled at NASA's launch facility at Kennedy Space Center. At the time of the development of previous human launch systems, there were other considerations that were deemed more important than developing worksites for ground crews; e.g., hardware development schedule and vehicle performance. However, experience with these systems has shown that failure to design for ground tasks has resulted in launch schedule delays, ground operations that are more costly than they might be, and threats to flight safety. As the Agency begins the development of new systems to return humans to the moon, the new Constellation Program is addressing this issue with a new set of human engineering requirements. Among these requirements is a subset that will apply to the design of the flight components and that is intended to assure ground crew success in vehicle assembly and maintenance tasks. These requirements address worksite design for usability and for ground crew safety.

  13. Keep it simple - A case study of model development in the context of the Dynamic Stocks and Flows (DSF) task

    NASA Astrophysics Data System (ADS)

    Halbrügge, Marc

    2010-12-01

    This paper describes the creation of a cognitive model submitted to the ‘Dynamic Stocks and Flows’ (DSF) modeling challenge. This challenge aims at comparing computational cognitive models for human behavior during an open ended control task. Participants in the modeling competition were provided with a simulation environment and training data for benchmarking their models while the actual specification of the competition task was withheld. To meet this challenge, the cognitive model described here was designed and optimized for generalizability. Only two simple assumptions about human problem solving were used to explain the empirical findings of the training data. In-depth analysis of the data set prior to the development of the model led to the dismissal of correlations or other parametric statistics as goodness-of-fit indicators. A new statistical measurement based on rank orders and sequence matching techniques is being proposed instead. This measurement, when being applied to the human sample, also identifies clusters of subjects that use different strategies for the task. The acceptability of the fits achieved by the model is verified using permutation tests.

  14. Examining pre-service science teachers' developing pedagogical design capacity for planning and supporting task-based classroom discussions

    NASA Astrophysics Data System (ADS)

    Ross, Danielle Kristina

    Teachers face many challenges as we move forward into the age of the Next Generation Science Standards (NGSS) (Achieve, Inc., 2013). The NGSS aim to develop a population of scientifically literate and talented students who can participate in the "innovation-driven economy" (p. 1). In order to meet these goals, teachers must provide students with opportunities to engage in science and engineering practices (SEPs) and learn core ideas of these disciplines. This study followed pre-service secondary science teachers as they participated in a secondary science teacher preparation program intended to support the development of their pedagogical design capacity (Brown, 2009) related to planning and supporting whole-class taskbased discussions. Teacher educators in this program designed an intervention that aimed in supporting this development. This study examined a particular dimension of PDC -- specifically, PSTs effective use of resources to plan science lessons in which students engage in a high demand task, participate in SEPs, and discuss their work in a whole-class setting. In order to examine the effectiveness of the intervention, I had to define PDC a priori. I measured PDC by documenting how/whether PSTs engaged in the following instructional planning practices: developing Learning Goals, selecting and/or designing challenging tasks, anticipating student thinking, planning for monitoring student thinking, imagining the discussion storyline, planning questions, and planning marking strategies. Analyses showed a significant difference between baseline lesson plan scores and Instructional Performance scores. These findings suggest these patterns and changes were directly linked to the teacher preparation program. The mean increase in Instructional Performance scores during the course of the teacher preparation year further supports the effect of the teacher preparation coursework. Pre-service teachers with high pedagogical design capacity continually integrated the

  15. 77 FR 71471 - Interagency Task Force on Veterans Small Business Development; Notice of Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-11-30

    ... on coordinating the efforts of Federal agencies to improve capital, business development... capital (loans, surety bonding and franchising); (2) Ensure achievement of pre-established contracting... accessing business development and entrepreneurship opportunities; (5) Increasing and improving training...

  16. 78 FR 45996 - Interagency Task Force on Veterans Small Business Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-30

    ... agencies to improve capital, business development opportunities and pre-established Federal contracting... proposals relating to ``six focus areas'': (1) Access to capital (loans, surety bonding and franchising); (2...) Reducing paperwork and administrative burdens in accessing business development and...

  17. Task-Level Control for a Full Semi-Autonomous Mission: Test Platform Development and Demonstration

    NASA Technical Reports Server (NTRS)

    Rock, Stephen M.; LeMaster, Edward A.

    2001-01-01

    Pseudolites can extend the availability of GPS-type positioning systems to a wide range of applications not possible with satellite-only GPS, including indoor and deep-space applications. Conventional GPS pseudolite arrays require that the devices be pre-calibrated through a survey of their locations, typically to sub-centimeter accuracy. This can sometimes be a difficult task, especially in remote or hazardous environments. By using the GPS signals that the pseudolites broadcast, however, it is possible to have the array self-survey its own relative locations, creating a Self-Calibrating Pseudolite Array (SCPA). In order to provide the bi-directional ranging signals between devices necessary for array self-calibration, pseudolite transceivers must be used. The basic principles behind the use of transceivers to create an SCPA were first presented in paper presented to the Institute of Navigation GPS-98 Conference. This paper begins with a brief review of the transceiver architecture and the fundamental direct-ranging algorithm presented in that paper. This is followed by a description of a prototype self-differencing transceiver system that has been constructed, and a presentation of experimental code- and carrier-phase ranging data obtained using that system. A second algorithm is then described which uses these fundamental range measurements between transceiver pairs to self-calibrate a larger stationary array and to provide positioning information for a vehicle moving within that array. Simulation results validating the accuracy and effective convergence of this algorithm are also presented.

  18. Heliobiology, its development, successes and tasks. [solar activity effects on life on earth

    NASA Technical Reports Server (NTRS)

    Platonova, A. T.

    1974-01-01

    Heliobiology studies the influence of changes in solar activity on life. Considered are the influence of periodic solar activity on the development and growth of epidemics, mortality from various diseases, the functional activity of the nervous system, the development of psychic disturbances, the details of the development of microorganisms and many other phenomena in the living world.

  19. Development of fireside performance indices, Task 7.33, Development of methods to predict agglomeration and deposition in FBCS, Task 7.36, Enhanced air toxics control, Task 7.45

    SciTech Connect

    Zygarlicke, C.J.; Mann, M.D.; Laudal, D.L.; Miller, S.J.

    1994-01-01

    The Energy & Environmental Research Center (EERC) has been developing advanced indices that rank coals according to their fouling and slagging propensity in utility boilers. The indices are based on sophisticated analytical techniques for identifying and quantifying coal inorganics and are useful in predicting the effects of proposed operational changes on ash deposition in coal-fired boilers. These indices are intended to provide an economical way to reduce the amount of full-scale testing needed to determine the best means of minimizing ash-related problems. The successful design and operation of the fluidized-bed combustor requires the ability to control and mitigate ash-related problems. The major ash-related problems in FBC are agglomeration of bed material, ash deposition on heat-transfer surfaces, ash deposition on refractory and uncooled surfaces, corrosion, and erosion. The focus of the Development of Methods to Predict Agglomeration and Deposition in FBCs is on the agglomeration and deposition problems in atmospheric bubbling and circulating beds. The 1990 Clean Air Act Amendments require study of air toxic emissions from coal combustion systems. Since most of the toxic metals present in coal will be in particulate form, a high level of fine-particle control appears to be the best approach to achieving a high level of air toxics control. However, over 50% of mercury and a portion of selenium emissions are in vapor form and are not typically collected in particulate control devices. Therefore, the goal of this project is to develop methods that capture the vapor-phase metals while simultaneously achieving ultrahigh collection efficiency of particulate air toxics.

  20. WFC3: Design and Development History

    NASA Astrophysics Data System (ADS)

    MacKenty, John W.; Kimble, R. A.; O'Connell, R. W.; Townsend, J. A.; WFC3 Team

    2010-01-01

    The Wide Field Camera 3 (WFC3) was developed to ensure that HST offers a high capability imager beyond SM4 and to significantly extend HST's performance in the near UV and near IR. This paper describes the eleven-year development history, major design decisions, and technology development items of WFC3, including a discussion of the consequences of schedule changes to the HST program. The decisions behind the re-use of WF/PC-1 hardware, the multiple ACS heritage elements, and our efforts to develop improved detectors and filters are considered. We also discuss the unique teaming, management and oversight arrangements adopted by WFC3.

  1. Inhibition of the cancer-associated TASK 3 channels by magnetically induced thermal release of Tetrandrine from a polymeric drug carrier.

    PubMed

    Shi, Chen; Thum, Carolin; Zhang, Qian; Tu, Wei; Pelaz, Beatriz; Parak, Wolfgang J; Zhang, Yu; Schneider, Marc

    2016-09-10

    Two-pore domain (K2P) potassium channels have recently attracted growing interest in the field of cancer research. These channels play an important role in cancer biology specifically for cancer progression, including proliferation, migration, and apoptosis, which makes them an attractive target for novel cancer therapies. Here, we examined the effect of Tetrandrine (Tet), a natural compound known as a channel modulator, which is associated with anticancer activities, as potential drug in this regard. Xenopus oocyte with overexpression of K2P 9.1 (TASK 3) channels has been chosen as model system for this purpose. In order to release Tet and trigger the channels we developed a polymeric magnetic delivery system: Tetrandrine-Magnetite co-loaded poly (lactic-co-glycolic) acid particles. The embedded iron oxide magnetite (Fe3O4) nanoparticles (NPs) allow to inductively heat the particles by applying a high frequency alternating magnetic field, and thus trigger the release of the co-encapsulated Tet. As a proof of concept the nanoparticulate drug delivery system was heated by raising the suspension's temperature proving the temperature dependent release behaviour. Both heating approaches were then successfully applied for measuring the TASK 3 channels current in response to the released drug. It was found that the released Tet amount is sufficient to inhibit the TASK 3 channels in a dose dependent manner. Thus, such a stimulus responsive drug delivery system holds great promise as a novel approach for the treatment of various cancer types such as for the interaction with the two-pore domain potassium channels K2P 9.1. PMID:27374629

  2. User Control and Task Authenticity for Spatial Learning in 3D Environments

    ERIC Educational Resources Information Center

    Dalgarno, Barney; Harper, Barry

    2004-01-01

    This paper describes two empirical studies which investigated the importance for spatial learning of view control and object manipulation within 3D environments. A 3D virtual chemistry laboratory was used as the research instrument. Subjects, who were university undergraduate students (34 in the first study and 80 in the second study), undertook…

  3. Advanced Oxyfuel Boilers and Process Heaters for Cost Effective CO2 Capture and Sequestration

    SciTech Connect

    Max Christie; Rick Victor; Bart van Hassel; Nagendra Nagabushana; Juan Li; Joseph Corpus; Jamie Wilson

    2007-03-31

    The purpose of the advanced boilers and process heaters program is to assess the feasibility of integrating Oxygen Transport Membranes (OTM) into combustion processes for cost effective CO{sub 2} capture and sequestration. Introducing CO{sub 2} capture into traditional combustion processes can be expensive, and the pursuit of alternative methods, like the advanced boiler/process heater system, may yield a simple and cost effective solution. In order to assess the integration of an advanced boiler/process heater process, this program addressed the following tasks: Task 1--Conceptual Design; Task 2--Laboratory Scale Evaluation; Task 3--OTM Development; Task 4--Economic Evaluation and Commercialization Planning; and Task 5--Program Management. This Final report documents and summarizes all of the work performed for the DOE award DE-FC26-01NT41147 during the period from January 2002-March 2007. This report outlines accomplishments for the following tasks: conceptual design and economic analysis, oxygen transport membrane (OTM) development, laboratory scale evaluations, and program management.

  4. The Effects of Synchronous Text-Based Computer-Mediated Communication Tasks on the Development of L2 and Academic Literacy: A Mixed Methods Study

    ERIC Educational Resources Information Center

    Li, Jinrong

    2012-01-01

    The dissertation examines how synchronous text-based computer-mediated communication (SCMC) tasks may affect English as a Second Language (ESL) learners' development of second language (L2) and academic literacy. The study is motivated by two issues concerning the use of SCMC tasks in L2 writing classes. First, although some of the alleged…

  5. Occupational Survey Report on Automotive Mechanics: Task Data from Workers and Supervisors Indicating Job Relevance and Training Criticalness. [Interim Report]. Research and Development Series No. 110.

    ERIC Educational Resources Information Center

    Ammerman, Harry L.; Pratzner, Frank C.

    The study was conducted to develop methods for using timely, firsthand occupational task information on automotive mechanics in order to identify critical performance requirements that warrant formal training. The methodology used is described in detail. A Task Inventory Questionnaire was completed by 18 auto mechanics and 12 supervisors in each…

  6. 14-3-3 proteins and plant development.

    PubMed

    Fulgosi, Hrvoje; Soll, Jürgen; de Faria Maraschin, Simone; Korthout, Henrie A A J; Wang, Mei; Testerink, Christa

    2002-12-01

    The 14-3-3 proteins are a family of ubiquitous regulatory molecules which have been found in virtually every eukaryotic organism and tissue. Discovered 34 years ago, 14-3-3 proteins have first been studied in mammalian nervous tissues, but in the past decade their indispensable role in various plant regulatory and metabolic pathways has been increasingly established. We now know that 14-3-3 members regulate fundamental processes of nitrogen assimilation and carbon assimilation, play an auxiliary role in regulation of starch synthesis, ATP production, peroxide detoxification, and participate in modulation of several other important biochemical pathways. Plant development and seed germination appear also to be under control of factors whose interaction with 14-3-3 molecules is crucial for their activation. Located within the nucleus, 14-3-3 isoforms are constituents of transcription factor complexes and interact with components of abscisic acid (ABA)-induced gene expression machinery. In addition, in animal cells they participate in nucleo-cytoplasmic trafficking and molecular sequestration. Cytoplasmic 14-3-3 members form a guidance complex with chloroplast destined preproteins and facilitate their import into these photosynthetic organelles. Recently, several 14-3-3s have been identified within chloroplasts where they could be involved in targeting and insertion of thylakoid proteins. The identification of 14-3-3 isoform specificity, and in particular the elucidation of the signal transduction mechanisms connecting 14-3-3 members with physiological responses, are central and developing topics of current research in this field.

  7. MP3 compression and transmission of infrasonic sensor array signals and task-specific metrics for distortion evaluation

    NASA Astrophysics Data System (ADS)

    Cabrera, Sergio D.; Vidal, Edward, Jr.; Paramanandan, Smitha

    2005-08-01

    Infrasonic sensor arrays are very useful for detecting natural and man-made events. This paper describes part of an ongoing project for compressing and transmitting a set of infrasonic signals that need to be delivered to a remote location for decompression and processing. The project also deals with the evaluation of the effect of the compression distortion on the signals by the use of task-specific distortion metrics. We evaluate the effectiveness of the scheme using one hour worth of signals that were collected during a Space Shuttle launch using a small array of 4 microphones. The approach described here is to combine the 4 signals/channels using a transmultiplexer and to use an off-the-shelf audio compression method, namely the popular MP3 method which is based on subband coding. The transmultiplexer is a 5-channel Cosine-Modulated filterbank from which only the first 4 channels are used.. The codec used in this study is the readily available LAME software package which allows one to choose the output bits per second rate and to turn off the psychoacoustic model. To use an audio coder, the combined signal is first converted to 16 bits per sample and then associated with a 16 KHz. sampling frequency. In the application considered, the microphone signals are used to compute time evolving quantities including: average spectral coherence, beamforming, and phase velocity. These same quantities are used as task-specific metrics that reveal the distortion caused by the application of the MP3 compressor so that the user can evaluate distortion tolerances. From visual evaluation of these metrics we conclude that a compression ratio between 6.4:1 and 8:1 produces negligible distortion in the three task-specific metrics. The beamforming metric is the most sensitive to the compression distortion.

  8. Experience of Using an Interdisciplinary Task Force to Develop a Culturally Sensitive Multipronged Tool to Improve Stroke Outcomes in Nigeria

    PubMed Central

    Arulogun, Oyedunni S.; Hurst, Samantha; Owolabi, Mayowa O.; Akinyemi, Rufus O.; Uvere, Ezinne; Saulson, Raelle; Ovbiagele, Bruce

    2016-01-01

    The burden of stroke is on the rise in Nigeria. A multi-faceted strategy is essential for reducing this growing burden and includes promoting medication adherence, optimizing traditional biomarker risk targets (blood pressure, cholesterol) and encouraging beneficial lifestyle practices. Successful implementation of this strategy is challenged by inadequate patient health literacy, limited patient/medical system resources, and lack of a coordinated interdisciplinary treatment approach. Moreover, the few interventions developed to improve medical care in Nigeria have generally been aimed at physicians (primarily) and nurses (secondarily) with minimal input from other key health care providers, and limited contributions from patients, caregivers, and the community itself. The Tailored Hospital-based Risk Reduction to Impede Vascular Events after Stroke (THRIVES) study is assessing the efficacy of a culturally sensitive multidimensional intervention for controlling blood pressure in recent stroke survivors. A key component of the intervention development process was the constitution of a project task force comprising various healthcare providers and administrators. This paper describes the unique experience in Sub-Saharan Africa of utilizing of an interdisciplinary Task Force to facilitate the development of the multipronged behavioral intervention aimed at enhancing stroke outcomes in a low-middle income country. PMID:27331144

  9. The development and implementation of a hospital safety and sanitation task force.

    PubMed

    Weinstein, S A; Whelan, M

    1985-01-01

    We have found that the above activities are facilitated by utilizing a computerized filing program. The computer formal provides quick, concise reports and statistical data analysis. The formation catalogued can be easily analysis. The information catalogued can be easily categorized and analyzed. The time invested in organizational meetings concerning committee membership, guideline review and creating an efficient incident coding scheme was essential to the success of the project. Problems seem to arise when several different departments share a common space for different activities. For example, medication room sanitation throughout the hospital was suboptimal probably related to the fact that Nursing, Pharmacy and General Stores all utilized the area. No individual department felt it was their sole responsibility to ensure appropriate sanitation. Through the efforts of the task force, we were able to facilitate cooperation among the departments with each doing their share. As a result, medication rooms are now cleaner, neater and therefore safer. Additional incidents have been corrected since the original tabulation of this report. A priority goal is to facilitate corrective action in a more timely manner. It is critical that surveys should not be intended to be "white glove inspections" with criticisms placed on specific departments. This can be accomplished by informing department managers of the intent of the surveys and by allowing staff to participate in all activities. In addition, the support and cooperation of administration is a major factor in the potential success of a program of this nature. As a result of the interdisciplinary team approach, the general safety environment for patients, visitors, employees and volunteers has significantly been improved at our institution.

  10. Tourism Technical Advisory Committee on Curriculum Development. Job Clusters, Competencies and Task Analysis.

    ERIC Educational Resources Information Center

    Northern Montana Coll., Havre. Montana Center for Vocational Education, Research, Curriculum and Personnel Development.

    This skills inventory for travel and tourism occupations was developed by a technical committee in Montana to assist in the development of model curricula and to address state labor market needs. The committee included employers from the travel and tourism industry, members of trade and professional associations, and educators. The validated task…

  11. Professional Development: A Six-Year Data Evaluation of HIDTA Law Enforcement Task Force Training Programs

    ERIC Educational Resources Information Center

    Burnett, Larry D.

    2012-01-01

    This is a nationwide six-year data study of law enforcement training and professional development in relationship to workplace productivity. Why do we care about law enforcement training and professional development? Because the law enforcement environment is not standing still. Unlawful activity, and in particular drug trafficking strategies,…

  12. Health Care Technical Advisory Committee on Curriculum Development. Job Clusters, Competencies and Task Analysis.

    ERIC Educational Resources Information Center

    Northern Montana Coll., Havre. Montana Center for Vocational Education, Research, Curriculum and Personnel Development.

    This skills inventory for health care occupations was developed by a technical committee in Montana to assist in the development of model curricula and to address state labor market needs. The committee included employers from hospitals and other health care providers, members of trade and professional associations, and educators. The validated…

  13. An Organizational and Task Perspective Model Aimed at Enhancing Teachers' Professional Development and Occupational Expertise

    ERIC Educational Resources Information Center

    Evers, Arnoud T.; Kreijns, Karel; Van der Heijden, Beatrice I. J. M.; Gerrichhauzen, John T. G.

    2011-01-01

    Currently, many countries, including the Netherlands, are "plagued" by severe, both quantitative and qualitative, teacher shortages that are even expected to increase in the years to come. Teachers' occupational development, therefore, has become an important issue on the research agenda of the respective countries. It is essential to develop more…

  14. Towards Improving the Strategies of Effective Teaching of Entrepreneurship Development Education Courses to Office Technology and Management Students of Polytechnics in Delta State

    ERIC Educational Resources Information Center

    Esene, Robert A.

    2015-01-01

    This study investigated the strategies and tools for effective teaching of Entrepreneurship Development Education to OTM students of Polytechnics in Delta State. The design of the study was survey. Research question was raised for the study. An instrument which consisted of 70 items was distributed to 30 respondents in the areas covered in the…

  15. Task 3: Evaluation of mineral resource potential, caldera geology, and volcano-tectonic framework at and near Yucca Mountain

    SciTech Connect

    Weiss, S.I.; Noble, D.C.; Larson, L.T.

    1994-12-31

    This report summarizes the work of Task 3 that was initially discussed in our monthly reports for the period October 1, 1993 through September 30, 1994, and is contained in our various papers and abstracts, both published and in press or currently in review. Our efforts during this period have involved the continuation of studies begun prior to October, 1993, focussed mainly on aspects of the caldera geology, magmatic activity, hydrothermal mineralization and extensional tectonics of the western and central parts of the southwestern Nevada volcanic field (SWNVF), studies of the subsurface rocks of Yucca Mountain utilizing drill-hole sampled obtained in 1991 and 1992, and studies of veins and siliceous ledges cropping out in northwestern Yucca Mountain. These veins and ledges provide evidence for near-surface hydrothermal activity in northwestern Yucca Mountain during the Crater Flat Tuff period of volcanism. During the period of this report we have concentrated our efforts on the production and publication of documents summarizing many of the data, interpretations and conclusions of Task 3 studies pertaining to hydrothermal activity and mineralization in the Yucca Mountain region and their relations to volcanism and tectonic activity. The resulting two manuscripts for journal publication and a compilation of radiometric age and trace-element geochemical data are appended to this report.

  16. Orbit Transfer Rocket Engine Technology Program: Advanced engine study, task D.1/D.3

    NASA Technical Reports Server (NTRS)

    Martinez, A.; Erickson, C.; Hines, B.

    1986-01-01

    Concepts for space maintainability of OTV engines were examined. An engine design was developed which was driven by space maintenance requirements and by a failure mode and effects (FME) analysis. Modularity within the engine was shown to offer cost benefits and improved space maintenance capabilities. Space operable disconnects were conceptualized for both engine change-out and for module replacement. Through FME mitigation the modules were conceptualized to contain the least reliable and most often replaced engine components. A preliminary space maintenance plan was developed around a controls and condition monitoring system using advanced sensors, controls, and condition monitoring concepts. A complete engine layout was prepared satisfying current vehicle requirements and utilizing projected component advanced technologies. A technology plan for developing the required technology was assembled.

  17. Space station integrated wall design and penetration damage control. Task 3: Theoretical analysis of penetration mechanics

    NASA Technical Reports Server (NTRS)

    Bjorkman, M. D.; Geiger, J. D.; Wilhelm, E. E.

    1987-01-01

    The efforts to provide a penetration code called PEN4 version 10 is documented for calculation of projectile and target states for the impact of 2024-T3 aluminum, R sub B 90 1018 steel projectiles and icy meteoroids onto 2024-T3 aluminum plates at impact velocities from 0 to 16 km/s. PEN4 determines whether a plate is perforated by calculating the state of fragmentation of projectile and first plate. Depth of penetration into the second to n sup th plate by fragments resulting from first plate perforation is determined by multiple cratering. The results from applications are given.

  18. Space station needs, attributes and architectural options. Volume 3, attachment 1, task 1: Mission requirements

    NASA Technical Reports Server (NTRS)

    1983-01-01

    The development and systems architectural requirements of the space station program are described. The system design is determined by user requirements. Investigated topics include physical and life science experiments, commercial utilization, U.S. national security, and remote space operations. The economic impact of the space station program is analyzed.

  19. D.C. Public School and Public Charter School Capital Budgeting: Task 3 Report

    ERIC Educational Resources Information Center

    Filardo, Mary; Rivlin, Alice M.; O'Cleireacain, Carol; Garrison, David

    2005-01-01

    The District of Columbia is four years into the implementation of a ten year Educational Facility Master Plan and seven years into the development of Public Charter Schools. A great deal of work to improve public school facilities has been done. The new buildings and renovations that have been completed by the District of Columbia Public Schools…

  20. 75 FR 22497 - Interagency Task Force on Veterans Small Business Development

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-29

    ... agencies to improve capital, business development opportunities, and pre-established Federal contracting... proposals relating to: (i) improving capital access and capacity of small business concerns owned and... and entrepreneurship opportunities; ] (v) increasing and improving training and counseling...

  1. 3 CFR - Establishing an Interagency Task Force on Federal Contracting Opportunities for Small Businesses

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ..., including businesses owned by women, minorities, socially and economically disadvantaged individuals, and... Underutilized Business Zones (at least 3 percent) or that are owned by women (at least 5 percent), socially and... firms owned by women, minorities, socially and economically disadvantaged individuals, and...

  2. Space station systems analysis study. Part 3: Documentation. Volume 7: SCB alternate EPS evaluation, task 10

    NASA Technical Reports Server (NTRS)

    1977-01-01

    Power levels up to 100 kWe average were baselined for the electrical power system of the space construction base, a long-duration manned facility capable of supporting manufacturing and large scale construction projects in space. Alternatives to the solar array battery systems discussed include: (1) solar concentrator/brayton; (2) solar concentrator/thermionic; (3) isotope/brayton; (4) nuclear/brayton; (5) nuclear thermoelectric; and (6) nuclear thermionic.

  3. Process development for automated solar cell and module production. Task 4: automated array assembly

    SciTech Connect

    Hagerty, J.J.

    1980-06-30

    The scope of work under this contract involves specifying a process sequence which can be used in conjunction with automated equipment for the mass production of solar cell modules for terrestrial use. This process sequence is then critically analyzed from a technical and economic standpoint to determine the technological readiness of each process step for implementation. The process steps are ranked according to the degree of development effort required and according to their significance to the overall process. Under this contract the steps receiving analysis were: back contact metallization, automated cell array layup/interconnect, and module edge sealing. For automated layup/interconnect both hard automation and programmable automation (using an industrial robot) were studied. The programmable automation system was then selected for actual hardware development. Economic analysis using the SAMICS system has been performed during these studies to assure that development efforts have been directed towards the ultimate goal of price reduction. Details are given. (WHK)

  4. Process development for automated solar cell and module production. Task 4: Automated array assembly

    NASA Technical Reports Server (NTRS)

    1980-01-01

    A process sequence which can be used in conjunction with automated equipment for the mass production of solar cell modules for terrestrial use was developed. The process sequence was then critically analyzed from a technical and economic standpoint to determine the technological readiness of certain process steps for implementation. The steps receiving analysis were: back contact metallization, automated cell array layup/interconnect, and module edge sealing. For automated layup/interconnect, both hard automation and programmable automation (using an industrial robot) were studied. The programmable automation system was then selected for actual hardware development.

  5. Job/Task Analysis: Enhancing the Commercial Building Workforce Through the Development of Foundational Materials; Preprint

    SciTech Connect

    Studer, D.; Kemkar, S.

    2012-09-01

    For many commercial building operation job categories, industry consensus has not been reached on the knowledge, skills, and abilities that practitioners should possess. The goal of this guidance is to help streamline the minimum competencies taught or tested by organizations catering to building operations and maintenance personnel while providing a basis for developing and comparing new and existing training programs in the commercial building sector. The developed JTAs will help individuals identify opportunities to enhance their professional skills, enable industry to identify an appropriately skilled workforce, and allow training providers to ensure that they are providing the highest quality product possible.

  6. Low cost silicon solar array project large area silicon sheet task: Silicon web process development

    NASA Technical Reports Server (NTRS)

    Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Blais, P. D.; Davis, J. R., Jr.

    1977-01-01

    Growth configurations were developed which produced crystals having low residual stress levels. The properties of a 106 mm diameter round crucible were evaluated and it was found that this design had greatly enhanced temperature fluctuations arising from convection in the melt. Thermal modeling efforts were directed to developing finite element models of the 106 mm round crucible and an elongated susceptor/crucible configuration. Also, the thermal model for the heat loss modes from the dendritic web was examined for guidance in reducing the thermal stress in the web. An economic analysis was prepared to evaluate the silicon web process in relation to price goals.

  7. Human Factors Process Task Analysis Liquid Oxygen Pump Acceptance Test Procedure for the Advanced Technology Development Center

    NASA Technical Reports Server (NTRS)

    Diorio, Kimberly A.

    2002-01-01

    A process task analysis effort was undertaken by Dynacs Inc. commencing in June 2002 under contract from NASA YA-D6. Funding was provided through NASA's Ames Research Center (ARC), Code M/HQ, and Industrial Engineering and Safety (IES). The John F. Kennedy Space Center (KSC) Engineering Development Contract (EDC) Task Order was 5SMA768. The scope of the effort was to conduct a Human Factors Process Failure Modes and Effects Analysis (HF PFMEA) of a hazardous activity and provide recommendations to eliminate or reduce the effects of errors caused by human factors. The Liquid Oxygen (LOX) Pump Acceptance Test Procedure (ATP) was selected for this analysis. The HF PFMEA table (see appendix A) provides an analysis of six major categories evaluated for this study. These categories include Personnel Certification, Test Procedure Format, Test Procedure Safety Controls, Test Article Data, Instrumentation, and Voice Communication. For each specific requirement listed in appendix A, the following topics were addressed: Requirement, Potential Human Error, Performance-Shaping Factors, Potential Effects of the Error, Barriers and Controls, Risk Priority Numbers, and Recommended Actions. This report summarizes findings and gives recommendations as determined by the data contained in appendix A. It also includes a discussion of technology barriers and challenges to performing task analyses, as well as lessons learned. The HF PFMEA table in appendix A recommends the use of accepted and required safety criteria in order to reduce the risk of human error. The items with the highest risk priority numbers should receive the greatest amount of consideration. Implementation of the recommendations will result in a safer operation for all personnel.

  8. Students' Development and Use of Internal Representations When Solving Algebraic Tasks

    ERIC Educational Resources Information Center

    Cross, Laban J.

    2013-01-01

    The difficulty in observing, recording, and examining internal representations has been well documented (Goldin & Shteingold, 2001). However, the important role that these internal representations play in the learning and understanding of mathematical concepts has been noted (Yackel, 2000). This study sought to develop a framework for…

  9. Planning and Second Language Development in Task-Based Synchronous Computer-Mediated Communication

    ERIC Educational Resources Information Center

    Hsu, Hsiu-Chen

    2012-01-01

    This dissertation explored the effect of two planning conditions (the multiple planning condition with rehearsal and online planning time, and the single planning condition with online planning time only) on L2 production complexity and accuracy and the subsequent development of these two linguistic areas in the context of written synchronous…

  10. The Development of Drawing Rules: Metaknowledge about Drawing Influences Performance on Nondrawing Tasks.

    ERIC Educational Resources Information Center

    Taylor, Marjorie; Bacharach, Verne R.

    1981-01-01

    Preschool children were asked to choose the figure most resembling a real man from three figures drawn according to formulas used by children to depict humans. Results suggest development of drawing systems influences children's conceptions about objects or events. (Author/DB)

  11. Fostering Creativity through Educational Video Game Development Projects: A Study of Contextual and Task Characteristics

    ERIC Educational Resources Information Center

    Fabricatore, Carlo; López, Ximena

    2013-01-01

    The increasing demand for creative individuals in the labor market requires well-prepared professionals, capable of enhancing competitiveness through new ideas and innovative actions. Educational programs should, therefore, rely on approaches and learning environments that foster creativity. In this study, video game development projects were used…

  12. The Valley Task: Understanding Intention from Goal-Directed Motion in Typical Development and Autism

    ERIC Educational Resources Information Center

    Castelli, Fulvia

    2006-01-01

    A novel paradigm investigates the ability to understand an agent's intended goal in children with autism (N = 25), typically developing children (N = 46), and adults (N = 16+12) by watching a non-human agent's kinematic properties alone. Computer animations depict a circle at the bottom of a U-shaped valley rolling up and down its slopes and…

  13. Developing the Second Language Writing Process through Social Media-Based Interaction Tasks

    ERIC Educational Resources Information Center

    Gómez, Julian Esteban Zapata

    2015-01-01

    This paper depicts the results from a qualitative research study focused on finding out the effect of interaction through social media on the development of second language learners' written production from a private school in Medellín, Antioquia, Colombia. The study was framed within concepts such as "social interaction," "digital…

  14. Systems Development in Guidance--a Learning-Task-Centered Approach. Final Report.

    ERIC Educational Resources Information Center

    Banathy, Bela H.; And Others

    To develop a systems-oriented model for guidance and counseling at all levels of schooling, a research project was conducted in a California school district, testing the applicability of systems concepts in guidance at the kindergarten and first grade levels. The project report includes a review of literature relating the systems approach to…

  15. Validation of the guidelines for portable meteorological instrument packages. Task IV. Development of an insolation handbook and instrumentation package

    SciTech Connect

    1980-10-01

    The purpose of this report is to show how the objective of developing guidelines for a solar energy related portable meteorology instrument package, under the auspices of the International Energy Agency (IEA), was carried out and preliminarily demonstrated and validated. A project to develop guidelines for such packages was initiated at IEA's Solar Heating and Cooling of Buildings Program Expert's Meeting held in Norrkoping, Sweden in February 1976. An international comparison of resultant devices was conducted on behalf of the IEA at a conference held in Hamburg, Federal Republic of Germany, in 1978. Results of the 1978 Hamburg comparison of two devices and the Swiss Mobile Solar Radiation System, using German meteorological standards, are discussed. The consensus of the IEA Task Group is that the objective of the subtask has been accomplished.

  16. Engineering Task Plan for Development and Fabrication and Deployment of Nested Fixed Depth Fluidic Sampling and At Tank Analysis Systems

    SciTech Connect

    BOGER, R.M.

    2000-10-30

    This engineering task plan identifies the resources, responsibilities, and schedules for the development and deployment of a mobile, variable depth sampling system and an at-tank analysis system. The mobile, variable depth sampling system concept was developed after a cost assessment indicated a high cost for multiple deployments of the nested, fixed-depth sampling system. The sampling will provide double-shell tank (DST) staging tank waste samples for assuring the readiness of the waste for shipment to the LAW/HLW plant for treatment and immobilization. The at-tank analysis system will provide ''real-time'' assessments of the samples' chemical and physical properties. These systems support the Hanford Phase 1B vitrification project.

  17. Task 3 -- Pyrolysis of plastic waste. Semi-annual report, April 1--September 30, 1997

    SciTech Connect

    Ness, R.O.; Aulich, T.R.

    1997-09-01

    The Energy and Environmental Research Center is developing a technology for the thermal decomposition of high-organic-content, radionuclide-contaminated mixed wastes and spent (radioactive) ion-exchange resins from the nuclear power industry that will enable the separation and concentration of radionuclides as dry particulate solids and the generation of nonradioactive condensable and noncondensable gas products. Successful application of the technology will enable a significant volume reduction of radioactive waste and the production of an inexpensively disposable nonradioactive organic product. The project objective is to develop and demonstrate the commercial viability of a continuous thermal decomposition process that can fulfill the following requirements: separate radionuclides from radioactive waste streams containing a variety of types and levels of polymers, chlorinated species, and other organics, including rubber, oils, resins, and cellulosic-based materials; concentrate radionuclides in a homogeneous, dry particulate product that can be recovered, handled, and disposed of efficiently and safely; separate and recover any chlorine present (as PVC, chlorinated solvents, or inorganic chlorine) in the contaminated mixed-waste stream; and yield a nonradioactive, low-chlorine-content, condensable organic product that can be economically disposed. Progress is described.

  18. THE METABOTROPIC GLUTAMATE 2/3 RECEPTOR AGONIST LY379268 COUNTERACTED KETAMINE-AND APOMORPHINE-INDUCED PERFORMANCE DEFICITS IN THE OBJECT RECOGNITION TASK, BUT NOT OBJECT LOCATION TASK, IN RATS

    PubMed Central

    Pitsikas, Nikolaos; Markou, Athina

    2014-01-01

    Experimental evidence indicates that the non competitive N-methyl-D-aspartate (NMDA) receptor antagonist ketamine and the mixed dopamine (DA) D1/D2 receptor agonist apomorphine induce schizophrenia-like symptoms in rodents, including cognitive deficits. Activation of Group II metabotropic glutamate 2/3 (mGlu2/3) receptors reduces the excessive glutamate release that is hypothesized to be associated with psychiatric disorders. Thus, mGlu2/3 receptor agonists may reverse deficits induced by excessive glutamate or DA release induced by administration of NMDA receptor antagonists and DA receptor agonists, respectively, and potentially those seen in schizophrenia. LY379268 is a selective mGlu2/3 receptor agonist that has shown to be effective in several animal models of stroke, epilepsy, and drug abuse. The present study investigated whether LY379268 antagonizes non-spatial and spatial recognition memory deficits induced by ketamine and apomorphine administration in rats. To assess the effects of the compounds on non-spatial and spatial recognition memory, the object recognition task and object location task were used. Post-training administration of LY379268 (1-3 mg/kg, i.p.) counteracted ketamine (3 mg/kg, i.p.) and apomorphine (1 mg/kg, i.p.)-induced performance deficits in the object recognition task. In contrast, LY379268 (1-3 mg/kg, i.p.) did not attenuate spatial recognition memory deficits produced by ketamine (3 mg/kg, i.p.) or apomorphine (1 mg/kg, i.p.) in the object location task. The present data show that the mGlu2/3 receptor agonist LY379268 reversed non-spatial, but not spatial, recognition memory deficits induced by NMDA receptor blockade or DA receptor agonism in rodents. Thus, such mGlu2/3 receptor agonists may be efficacious in reversing some memory deficits seen in schizophrenia patients. PMID:24859609

  19. Performance and cost models for the direct sulfur recovery process. Task 1 Topical report, Volume 3

    SciTech Connect

    Frey, H.C.; Williams, R.B.

    1995-09-01

    The purpose of this project is to develop performance and cost models of the Direct Sulfur Recovery Process (DSRP). The DSRP is an emerging technology for sulfur recovery from advanced power generation technologies such as Integrated Gasification Combined Cycle (IGCC) systems. In IGCC systems, sulfur present in the coal is captured by gas cleanup technologies to avoid creating emissions of sulfur dioxide to the atmosphere. The sulfur that is separated from the coal gas stream must be collected. Leading options for dealing with the sulfur include byproduct recovery as either sulfur or sulfuric acid. Sulfur is a preferred byproduct, because it is easier to handle and therefore does not depend as strongly upon the location of potential customers as is the case for sulfuric acid. This report describes the need for new sulfur recovery technologies.

  20. Use of ERTS imagery in air pollution and marine biology studies, tasks 1 through 3

    NASA Technical Reports Server (NTRS)

    Copeland, G. E.; Ludwick, J. C.; Marshall, H. G. (Principal Investigator); Bandy, A. R.; Fleischer, P.; Hanna, W. J.; Gosink, T. A.; Bowker, D. W.

    1972-01-01

    There are no author-identified significant results in this report. The general suitability of ERTS imagery in detecting ground originated air pollution has proved to be excellent. The quality and resolution exceeded expectations and has permitted in some instances location of point sources to within a thousand feet. Suitable techniques have not yet been developed for determining or measuring area and line sources of air pollution. A major problem has been cloud cover that has persisted over the area of primary interest, the Chesapeake Bay. Work has been completed on mounting the shipboard transmissometer which will be used for investigations to relate the chlorophyll and suspended sediment content in the waters of the Lower Chesapeake Bay to ERTS-1 imagery. Water sampling, plankton analysis, and preparations for sea collection of water truth along the eastern continental shelf of the U.S. have been completed for use in comparisons with ERTS-1 data.

  1. Private Speech in Children with ADHD and Their Typically Developing Peers during Problem-Solving and Inhibition Tasks

    ERIC Educational Resources Information Center

    Corkum, Penny; Humphries, Kelly; Mullane, Jennifer C.; Theriault, France

    2008-01-01

    This study compared private speech of children with ADHD and normal controls during problem solving and inhibition tasks. Thirty-two children (16 children with ADHD and 16 matched controls) aged 6-11 years participated. Consistent with previous studies, children with ADHD produced more task-irrelevant and task-relevant external private speech than…

  2. Development of a Software Tool to Automate ADCO Flight Controller Console Planning Tasks

    NASA Technical Reports Server (NTRS)

    Anderson, Mark G.

    2011-01-01

    This independent study project covers the development of the International Space Station (ISS) Attitude Determination and Control Officer (ADCO) Planning Exchange APEX Tool. The primary goal of the tool is to streamline existing manual and time-intensive planning tools into a more automated, user-friendly application that interfaces with existing products and allows the ADCO to produce accurate products and timelines more effectively. This paper will survey the current ISS attitude planning process and its associated requirements, goals, documentation and software tools and how a software tool could simplify and automate many of the planning actions which occur at the ADCO console. The project will be covered from inception through the initial prototype delivery in November 2011 and will include development of design requirements and software as well as design verification and testing.

  3. Task 10 - Technology Development Integration. Semiannual report, November 1, 1996--March 31, 1997

    SciTech Connect

    Erickson, Thomas A.; Daly, Daniel J.

    1997-12-31

    The Energy and Environmental Research Center (EERC) in conjunction with the Waste Policy Institute (WPI) will identify and integrate new technologies to meet site-specific environmental management (EM) requirements at contaminated sites appropriate to U.S. Department of Energy (DOE) interests. EM technologies offered by developers will be evaluated to determine their complementary contribution to new cleanup systems focused on particular characterization and remediation problems at specific EM sites. The technology clusters identified will provide EM cleanup capabilities that are significantly faster, better, safer, and cheaper than systems that are currently available. Work will be performed under the DOE-EERC EM Cooperative Agreement (EMCA), which includes provisions to develop, demonstrate, and commercialize technologies that address environmental management needs of contaminated sites together with management activities which accelerate transfer of technologies. The effort began July 1, 1995.

  4. Development of seal ring carbon-graphite materials (tasks 8, 9, and 10)

    NASA Technical Reports Server (NTRS)

    Fechter, N. J.; Petrunich, P. S.

    1973-01-01

    A screening study was conducted to develop improved carbon-graphite materials for use in self-acting seals at air temperatures to 1300 F (704 C). Property measurements on materials prepared during this study have shown that: (1) The mechanical properties of a carbon-graphite material were significantly improved by using a fine milled artificial graphite filler material and including intensive mixing, warm molding, and pitch impregnation in the processing; and (2) the oxidation resistance of a carbon-graphite material was improved by including fine milled boron carbide as an oxidation-inhibiting additive. These techniques were employed to develop a material that has 10 times more oxidation resistance than that of a widely used commercial grade and mechanical properties that approach those of the commercial grade.

  5. Development of residential-conservation-survey methodology for the US Air Force. Interim report. Task two

    SciTech Connect

    Abrams, D. W.; Hartman, T. L.; Lau, A. S.

    1981-11-13

    A US Air Force (USAF) Residential Energy Conservation Methodology was developed to compare USAF needs and available data to the procedures of the Residential Conservation Service (RCS) program as developed for general use by utility companies serving civilian customers. Attention was given to the data implications related to group housing, climatic data requirements, life-cycle cost analysis, energy saving modifications beyond those covered by RCS, and methods for utilizing existing energy consumption data in approaching the USAF survey program. Detailed information and summaries are given on the five subtasks of the program. Energy conservation alternatives are listed and the basic analysis techniques to be used in evaluating their thermal performane are described. (MCW)

  6. Feasibility study of modern airships, phase 1. Volume 2: Parametric analysis (task 3). [lift, weight (mass)

    NASA Technical Reports Server (NTRS)

    Lancaster, J. W.

    1975-01-01

    Various types of lighter-than-air vehicles from fully buoyant to semibuoyant hybrids were examined. Geometries were optimized for gross lifting capabilities for ellipsoidal airships, modified delta planform lifting bodies, and a short-haul, heavy-lift vehicle concept. It is indicated that: (1) neutrally buoyant airships employing a conservative update of materials and propulsion technology provide significant improvements in productivity; (2) propulsive lift for VTOL and aerodynamic lift for cruise significantly improve the productivity of low to medium gross weight ellipsoidal airships; and (3) the short-haul, heavy-lift vehicle, consisting of a simple combination of an ellipsoidal airship hull and existing helicopter componentry, provides significant potential for low-cost, near-term applications for ultra-heavy lift missions.

  7. MATERIALS DEVELOPMENT FOR PULP AND PAPER MILLS, TASK 9 PROOF OF COMMERCIAL CONCEPT: COMMODITY CARBON FIBERS FROM WEYERHAEUSER LIGNIN BASED FIBERS

    SciTech Connect

    Paulauskas, F.L.; Naskar, A.K.; S. Ozcan; J. R. Keiser; Gorog, J.P.

    2010-08-15

    Tasks were assigned to Oak Ridge National Laboratory (ORNL) researchers for the development of lignin-based carbon fiber from a specific precursor that was produced by the Participant (Weyerhaeuser Corporation). These tasks included characterization of precursor polymers and fibers; and the development of conversion parameters for the fibers. ORNL researchers provided recommendations for in-house characterization of the precursor at the participant’s laboratory.

  8. Advanced coal-fueled gas turbine systems: Subscale combustion testing. Topical report, Task 3.1

    SciTech Connect

    Not Available

    1993-05-01

    This is the final report on the Subscale Combustor Testing performed at Textron Defense Systems` (TDS) Haverhill Combustion Laboratories for the Advanced Coal-Fueled Gas Turbine System Program of the Westinghouse Electric Corp. This program was initiated by the Department of Energy in 1986 as an R&D effort to establish the technology base for the commercial application of direct coal-fired gas turbines. The combustion system under consideration incorporates a modular staged, rich-lean-quench, Toroidal Vortex Slogging Combustor (TVC) concept. Fuel-rich conditions in the first stage inhibit NO{sub x} formation from fuel-bound nitrogen; molten coal ash and sulfated sorbent are removed, tapped and quenched from the combustion gases by inertial separation in the second stage. Final oxidation of the fuel-rich gases, and dilution to achieve the desired turbine inlet conditions are accomplished in the third stage, which is maintained sufficiently lean so that here, too, NO{sub x} formation is inhibited. The primary objective of this work was to verify the feasibility of a direct coal-fueled combustion system for combustion turbine applications. This has been accomplished by the design, fabrication, testing and operation of a subscale development-type coal-fired combustor. Because this was a complete departure from present-day turbine combustors and fuels, it was considered necessary to make a thorough evaluation of this design, and its operation in subscale, before applying it in commercial combustion turbine power systems.

  9. Combined 3-D auditory-visual cueing for a visual target acquisition task

    NASA Astrophysics Data System (ADS)

    Westergren, Rachael L.; Havig, Paul R.; Heft, Eric L.

    2007-04-01

    Previous studies have shown that helmet-mounted displays (HMDs) are advantageous in maintaining situation awareness and increasing the amount of time pilots spend looking off-boresight (Geiselman & Osgood, 1994; Geiselman & Osgood, 1995). However, space is also limited on a HMD and any symbology that is presented takes up valuable space and can occlude a pilot's vision. There has been much research in the area of visual cueing and visual search as they relate to seeking out visual targets in the sky. However, the idea of localized auditory cueing, as it could apply in the realm of air-to-air targeting, is an area less studied. One question is how can we present information such that a pilot's attention will be directed to the object of interest the most quickly? Some different types of target location cueing symbology have been studied to find such aspects of symbology that will aid a pilot most in acquiring a target. The purpose of this study is to determine the best method of cueing a person to visual targets in the shortest amount of time possible using auditory and visual cues in combination. Specifically, participants were presented with different combinations of reflected line cues, standard line cues, and localized auditory cues for primary and secondary targets. The cues were presented using an HMD and 3-D auditory headphones, with a magnetic head tracker used to determine when the participant had visually acquired the targets. The possible benefits of these cues based on the times to acquire are discussed.

  10. JV Task 94 - Air Quality V: Mercury, Trace Elements, SO3, and Particulate Matter Conference

    SciTech Connect

    Thomas A. Erickson

    2007-01-31

    This final report summarizes the planning, preparation, facilitation and production, and summary of the conference entitled 'Air Quality V: Mercury, Trace Elements, SO{sub 3}, and Particulate Matter,' held September 18-21, 2005, in Arlington, Virginia. The goal of the conference was to build on the discussions of the first four Air Quality Conferences, providing further opportunity for leading representatives of industry, government, research institutions, academia, and environmental organizations to discuss the key interrelationships between policy and science shaping near-term regulations and controls and to assist in moving forward on emerging issues that will lead to acceptable programs and policies to protect human health, the environment, and economic growth. The conference was extremely timely, as it was the last large conference prior to publication of the U.S. Environmental Protection Agency's final regulations for mercury control from coal-fired utilities, and provided a forum to realistically assess the status of mercury controls in relation to the new regulations.

  11. Chemical Composiiton Analysis of INEEL Phase 3 Glasses: Task Technical and QA Plan

    SciTech Connect

    Peeler, D.

    2000-08-11

    For about four decades radioactive wastes have been collected and calcined from nuclear fuels reprocessing at the Idaho Chemical Processing Plant (ICPP). Over this time span, secondary radioactive waste from decontamination, laboratory activities and fuels storage activities have also been collected and stored as liquid. These liquid high-activity wastes (HAW) are collectively called Sodium Bearing Wastes (SBW). Currently about 5.7 million liters of these wastes are temporarily stored in stainless steel tanks at the Idaho National Engineering and Environmental Laboratory (INEEL). Vitrification is being considered as a treatment option for SBW. The resulting glass can be sent to either the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico, as remote handled transuranic waste (RH-TRU) or to the federal geologic repository for final disposal. In addition to the SBW, roughly 4,000 m3 of calcined high-level wastes (HLW) are currently being stored at INEEL in stainless steel bin sets. These calcined HLW may also be vitrified, either with or without a dissolution and separation process, and sent to the federal geologic repository for final disposal.

  12. Development of fireside performance indices - task 8. Topical report, March 1996

    SciTech Connect

    1995-11-01

    The primary goal of the Fireside Performance Indices (FPI) research project at the Energy & Environmental Research Center (EERC) was to develop a series of indices to reliably predict the fireside performance of subbituminous coals in utility boilers. Individual utilities must respond quickly and effectively to changing fuel markets because of competition within the U.S. coal-fired power industry. Spot-market purchases of coal have become commonplace. The economics associated with sulfur emissions control have caused many utilities to use Powder River Basin (PRB) subbituminous coals. The PRB coals usually provide a lower-cost, medium-heating-value, low-sulfur fuel option. Although these coals possess similar overall or bulk compositional properties, their fireside performance characteristics vary considerably within a given boiler. Consequently, bulk compositional parameters and, hence, conventional indices such as the base-to-acid ratio, stagging factor, and fouling factor are inappropriate for predicting the fireside performance of PRB coals. The development of the computer-controlled scanning electron microscopy (CCSEM) and chemical fractionation methods, however, has enabled a more thorough characterization of the inorganic constituents of PRB, coals that contribute to the following adverse operational effects: stagging, fouling, opacity, erosion and poor grindability, slag tapping, and sootblower performance. Eight predictive indices have been developed based primarily on CCSEM and chemical fractionation analysis parameters to predict the propensity of a given coal or coal blend to cause operational problems. The indices were formulated using bench-, pilot-, and full-scale combustion testing data from previous research projects combined with bench-scale data from this project to identify the primary coal inorganic properties that cause ash-related problems in utility boilers.

  13. Blade loss transient dynamics analysis, volume 1. Task 2: TETRA 2 theoretical development

    NASA Technical Reports Server (NTRS)

    Gallardo, Vincente C.; Black, Gerald

    1986-01-01

    The theoretical development of the forced steady state analysis of the structural dynamic response of a turbine engine having nonlinear connecting elements is discussed. Based on modal synthesis, and the principle of harmonic balance, the governing relations are the compatibility of displacements at the nonlinear connecting elements. There are four displacement compatibility equations at each nonlinear connection, which are solved by iteration for the principle harmonic of the excitation frequency. The resulting computer program, TETRA 2, combines the original TETRA transient analysis (with flexible bladed disk) with the steady state capability. A more versatile nonlinear rub or bearing element which contains a hardening (or softening) spring, with or without deadband, is also incorporated.

  14. Large area sheet task. Advanced dendritic web growth development. [silicon films

    NASA Technical Reports Server (NTRS)

    Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.; Meier, D.; Frantti, E.; Schruben, J.

    1981-01-01

    The development of a silicon dendritic web growth machine is discussed. Several refinements to the sensing and control equipment for melt replenishment during web growth are described and several areas for cost reduction in the components of the prototype automated web growth furnace are identified. A circuit designed to eliminate the sensitivity of the detector signal to the intensity of the reflected laser beam used to measure melt level is also described. A variable speed motor for the silicon feeder is discussed which allows pellet feeding to be accomplished at a rate programmed to match exactly the silicon removed by web growth.

  15. Process development for automated solar cell and module production. Task 4: Automated array assembly

    NASA Technical Reports Server (NTRS)

    Hagerty, J. J.

    1981-01-01

    Progress in the development of automated solar cell and module production is reported. The unimate robot is programmed for the final 35 cell pattern to be used in the fabrication of the deliverable modules. The mechanical construction of the automated lamination station and final assembly station phases are completed and the first operational testing is underway. The final controlling program is written and optimized. The glass reinforced concrete (GRC) panels to be used for testing and deliverables are in production. Test routines are grouped together and defined to produce the final control program.

  16. Integrated control and health monitoring capacitive displacement sensor development task. Orbit transfer rocket engine technology program

    NASA Technical Reports Server (NTRS)

    Collamore, Frank N.

    1989-01-01

    The development of a miniature multifunction turbomachinery shaft displacement sensor using state-of-the-art non-contract capacitive sensing technology is described. Axial displacement, radial displacement, and speed are sensed using a single probe within the envelope normally required for a single function. A survey of displacement sensing technology is summarized including inductive, capacitive, optical and ultrasonic techniques. The design and operation of an experimental triple function sensor is described. Test results are included showing calibration tests and simultaneous dynamic testing of multiple functions. Recommendations for design changes are made to improve low temperature performance, reliability, and for design of a flight type signal conditioning unit.

  17. Advanced power assessment for Czech lignite task 3.6. Topical report

    SciTech Connect

    Sondreal, E.A.; Mann, M.D.; Weber, G.W.; Young, B.C.

    1995-12-01

    Major reforms in the Czech energy sector have been initiated to reverse 40 years of central planning, subsidized energy pricing, unchecked pollution from coal-fired plants, concerns over nuclear safety and fuel cycle management, and dependence on the former U.S.S.R. for oil, gas, and nuclear fuel processing. Prices for electricity, heat, and natural gas paid by industry are close to western levels, but subsidized prices for households are as much as 40% lower and below economic cost. State control of major energy enterprises is being reduced by moving toward government-regulated, investor-owned companies to raise needed capital, but with a strategic stake retained by the state. Foreign firms will participate in privatization, but they are not expected to acquire a controlling interest in Czech energy companies. Economic conditions in the Czech Republic are now improving after the disruptions caused by restructuring since 1989 and separation of the former Czech and Slovak Federal Republics in January 1993. The downturn in the economy after 1989 was concentrated in energy-intensive heavy industry, and recovery is paced by consumer trade, services, light industry and construction. Energy use in relation to gross domestic product (GDP) has declined, but it is still significantly higher than in OECD (Organization for Economic Cooperation and Development) countries. The GDP increased by 2% in 1994 after dropping 22% between 1989 and 1993. A positive balance of payments has been achieved, with foreign investment offsetting a small trade deficit. The government`s external debt is only 4% of GDP. This report studies the application of lignite resources within the newly formulated energy policies of the republic, in light of a move toward privatization and stronger air pollution regulations. Lignite has represented the major energy source for the country.

  18. Task 3.7 -- Fuel utilization properties. Semi-annual report, January 1--June 30, 1995

    SciTech Connect

    Zygarlicke, C.J.

    1997-08-01

    The goal of the fuel utilization properties project was to determine the impacts of specific coal properties and additives on ash formation and deposition in advanced power systems. At the forefront of advanced power systems for coal utilization are pressurized fluidized bed (PFB) reactors and integrated gasifier-combined cycle (IGCC) reactors. Some of these systems are still in the infancy of their development and commercialization and very little is known about the types of ash deposition problems that could occur. Ash deposition in power generating systems is a significant problem that decreases efficiency and can lead to severe operational problems. During high temperature conversion of coal, the inorganic constituents in the coal are transformed into solid, liquid, and vapor species that differ in composition and size from the original inorganic constituents present in the coal. The chemical and physical properties of the intermediate ash stream are dependent in part upon the types, quantities and association of the minerals and other inorganics in the coal. There is a pressing need to obtain critical information on the aspects of inorganic transformations and deposit formation that will apply to advanced power systems so that mitigation measures can be prescribed such as predictive models, system design or operational changes, and the use of additives. The focus was on integrated gasification combined cycle (IGCC)-type systems, whereby small-scale furnaces were employed to simulate gasification or highly reducing conditions in order to produce entrained ash and deposits for analysis. Specific goals for this year`s work in the area of ash formation and deposition included the following: Determining the general chemical and physical properties of simulated entrained ash and deposits that may lead to operational problems, and Identifying and testing methods to mitigate deposition in IGCC-type systems.

  19. Large-area sheet task: Advanced dendritic-web-growth development

    NASA Technical Reports Server (NTRS)

    Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Schruben, J.

    1983-01-01

    Thermally generated stresses in the growing web crystal were reduced. These stresses, which if too high cause the ribbon to degenerate, were reduced by a factor of three, resulting in the demonstrated growth of high-quality web crystals to widths of 5.4 cm. This progress was brought about chiefly by the application of thermal models to the development of low-stress growth configurations. A new temperature model was developed which can analyze the thermal effects of much more complex lid and top shield configurations than was possible with the old lumped shield model. Growth experiments which supplied input data such as actual shield temperature and melt levels were used to verify the modeling results. Desirable modifications in the melt level-sensing circuitry were made in the new experimental web growth furnace, and this furnace has been used to carry out growth experiments under steady-state conditions. New growth configurations were tested in long growth runs at Westinghouse AESD which produced wider, lower stress and higher quality web crystals than designs previously used.

  20. Evaluation of minderal resource potential, Caldera geology, and volcano-tectonic framework at and near Yucca Mountain, Task 3

    SciTech Connect

    Weiss, S.I.; Noble, D.C.; Larson, L.T.

    1993-09-30

    This report summarizes the results of Task 3 work that was initially discussed in our monthly reports for the period October 1, 1992 through September 30, 1993, and contained in our various papers and abstracts, both published and currently in press or in review. Our work during this period was involved (a) the continuation of studies begun prior to October, 1992, focussed mainly on aspects of the caldera geology, volcanic stratigraphy, magmatic activity, hydrothermal mineralization and extensional tectonics of the western and northwestern parts of the southwestern and Nevada volcanic field (SWNVF), studies of the subsurface rocks of Yucca Mountain utilizing drill hole samples obtained in 1991 and 1992, and (b) new studies of veins and siliceous rocks cropping out in northwestern Yucca Mountain that provide evidence for previously unrecognized hydrothermal activity during the Crater Flat Tuff period of volcanism.

  1. DYNA3D Code Practices and Developments

    SciTech Connect

    Lin, L.; Zywicz, E.; Raboin, P.

    2000-04-21

    DYNA3D is an explicit, finite element code developed to solve high rate dynamic simulations for problems of interest to the engineering mechanics community. The DYNA3D code has been under continuous development since 1976[1] by the Methods Development Group in the Mechanical Engineering Department of Lawrence Livermore National Laboratory. The pace of code development activities has substantially increased in the past five years, growing from one to between four and six code developers. This has necessitated the use of software tools such as CVS (Concurrent Versions System) to help manage multiple version updates. While on-line documentation with an Adobe PDF manual helps to communicate software developments, periodically a summary document describing recent changes and improvements in DYNA3D software is needed. The first part of this report describes issues surrounding software versions and source control. The remainder of this report details the major capability improvements since the last publicly released version of DYNA3D in 1996. Not included here are the many hundreds of bug corrections and minor enhancements, nor the development in DYNA3D between the manual release in 1993[2] and the public code release in 1996.

  2. Task 3.3: Warm Syngas Cleanup and Catalytic Processes for Syngas Conversion to Fuels Subtask 3: Advanced Syngas Conversion to Fuels

    SciTech Connect

    Lebarbier Dagel, Vanessa M.; Li, J.; Taylor, Charles E.; Wang, Yong; Dagle, Robert A.; Deshmane, Chinmay A.; Bao, Xinhe

    2014-03-31

    activity was to develop methods and enabling materials for syngas conversion to SNG with readily CO2 separation. Suitable methanation catalyst and CO2 sorbent materials were developed. Successful proof-of-concept for the combined reaction-sorption process was demonstrated, which culminated in a research publication. With successful demonstration, a decision was made to switch focus to an area of fuels research of more interest to all three research institutions (CAS-NETL-PNNL). Syngas-to-Hydrocarbon Fuels through Higher Alcohol Intermediates There are two types of processes in syngas conversion to fuels that are attracting R&D interest: 1) syngas conversion to mixed alcohols; and 2) syngas conversion to gasoline via the methanol-to-gasoline process developed by Exxon-Mobil in the 1970s. The focus of this task was to develop a one-step conversion technology by effectively incorporating both processes, which is expected to reduce the capital and operational cost associated with the conversion of coal-derived syngas to liquid fuels. It should be noted that this work did not further study the classic Fischer-Tropsch reaction pathway. Rather, we focused on the studies for unique catalyst pathways that involve the direct liquid fuel synthesis enabled by oxygenated intermediates. Recent advances made in the area of higher alcohol synthesis including the novel catalytic composite materials recently developed by CAS using base metal catalysts were used.

  3. Box truss analysis and technology development. Task 1: Mesh analysis and control

    NASA Technical Reports Server (NTRS)

    Bachtell, E. E.; Bettadapur, S. S.; Coyner, J. V.

    1985-01-01

    An analytical tool was developed to model, analyze and predict RF performance of box truss antennas with reflective mesh surfaces. The analysis system is unique in that it integrates custom written programs for cord tied mesh surfaces, thereby drastically reducing the cost of analysis. The analysis system is capable of determining the RF performance of antennas under any type of manufacturing or operating environment by integrating together the various disciplines of design, finite element analysis, surface best fit analysis and RF analysis. The Integrated Mesh Analysis System consists of six separate programs: The Mesh Tie System Model Generator, The Loadcase Generator, The Model Optimizer, The Model Solver, The Surface Topography Solver and The RF Performance Solver. Additionally, a study using the mesh analysis system was performed to determine the effect of on orbit calibration, i.e., surface adjustment, on a typical box truss antenna.

  4. Development of response activation and inhibition in a selective stop-signal task.

    PubMed

    van de Laar, Maria C; van den Wildenberg, Wery P M; van Boxtel, Geert J M; van der Molen, Maurits W

    2014-10-01

    To gain more insight into the development of action control, the current brain potential study examined response selection, activation, and selective inhibition during choice- and stop-signal processing in three age groups (8-, 12-, and 21-year-olds). Results revealed that age groups differed in the implementation of proactive control; children slowed their go response and showed reduced cortical motor output compared to adults. On failed inhibition trials, children were less able than adults to suppress muscle output resulting in increased partial-inhibition rates. On invalid stop trials, all age groups initially activated, subsequently inhibited, and then reactivated the go response. Yet, children were less efficient in implementing this strategy. Then, older children recruit motor responses to a greater extent than younger children and adults, which reduced the efficiency of implementing response inhibition and proactive control. The results are discussed in relation to current notions of developmental change in proactive and reactive action control. PMID:25014630

  5. Development of a high temperature pH electrode for geothermal fluids. Final report, Task 1

    SciTech Connect

    Niedrach, L.W.; Stoddard, W.H.

    1981-04-01

    There has been no serious application of pH measurements above 150/sup 0/C stemming from the fact that there have been no practical probes available that are capable of operation under the required conditions of temperature and pressure. Recently, a new approach to such measurements was developed in which an oxygen ion conducting ceramic membrane (e.g., stabilized zirconia) is being employed in a sensor somewhat analogous to the glass electrode. The new sensor retains the specificity of the glass electrode, is equally insensitive to interference from redox active species, and possesses markedly superior resistance to attack by aqueous media at high temperatures. The status of the new sense at the inception of the contract is summarized and plans for the first year's investigation are outlined.

  6. Automated array assembly task development of low-cost polysilicon solar cells

    NASA Technical Reports Server (NTRS)

    Jones, G. T.

    1980-01-01

    Development of low cost, large area polysilicon solar cells was conducted in this program. Three types of polysilicon materialk were investigated. A theoretical and experimenal comparison between single crystal silicon and polysilicon solar cell efficiency was performed. Significant electrical performance differences were observed between types of wafer material, i.e. fine grain and coarse grain polysilicon and single crystal silicon. Efficiency degradation due to grain boundaries in fin grain and coarse grain polysilicon was shown to be small. It was demonstrated that 10 percent efficient polysilicon solar cells can be produced with spray on n+ dopants. This result fulfills an important goal of this project, which is the production of batch quantity of 10 percent efficient polysilicon solar cells.

  7. Development of seal ring carbon-graphite materials (tasks 5, 6, and 7)

    NASA Technical Reports Server (NTRS)

    Fechter, N. J.; Petrunich, P. S.

    1972-01-01

    Carbon-graphite seal ring bodies for operation at air temperatures to 1300 F(704 C) were manufactured from three select formulations. Mechanical and thermal properties, porosities, and oxidation rates were measured. The results have shown that: (1) Major property improvements anticipated from the screening studies were not realized because of processing problems associated with the scale-up in material size and probable deterioration of a phenolic resin binder; (2) the mechanical properties of a phenolic resin-bonded, carbon-graphite material can be improved by applying high pressure during carbonization; and (3) the textile form of graphite fiber used as the minor filler component in a carbon-graphite material can beneficially affect mechanical properties.

  8. TASK 3.4--IMPACTS OF COFIRING BIOMASS WITH FOSSIL FUELS

    SciTech Connect

    Christopher J. Zygarlicke; Donald P. McCollor; Kurt E. Eylands; Melanie D. Hetland; Mark A. Musich; Charlene R. Crocker; Jonas Dahl; Stacie Laducer

    2001-08-01

    less by the needs of the plant than by the availability in the soil solution; in addition to occurring naturally, Cl is present in excess as the anion complement in K fertilizer applications. An analysis was performed on existing data for switchgrass samples from ten different farms in the south-central portion of Iowa, with the goal of determining correlations between switchgrass elemental composition and geographical and seasonal changes so as to identify factors that influence the elemental composition of biomass. The most important factors in determining levels of various chemical compounds were found to be seasonal and geographical differences related to soil conditions. Combustion testing was performed to obtain deposits typical of boiler fouling and slagging conditions as well as fly ash. Analysis methods using computer-controlled scanning electron microscopy and chemical fractionation were applied to determine the composition and association of inorganic materials in the biomass samples. Modified sample preparation techniques and mineral quantification procedures using cluster analysis were developed to characterize the inorganic material in these samples. Each of the biomass types exhibited different inorganic associations in the fuel as well as in the deposits and fly ash. Morphological analyses of the wheat straw show elongated 10-30-{micro}m amorphous silica particles or phytoliths in the wheat straw structure. Alkali such as potassium, calcium, and sodium is organically bound and dispersed in the organic structure of the biomass materials. Combustion test results showed that the blends fed quite evenly, with good burnout. Significant slag deposit formation was observed for the 100% wheat straw, compared to bituminous and subbituminous coals burned under similar conditions. Although growing rapidly, the fouling deposits of the biomass and coal-biomass blends were significantly weaker than those of the coals. Fouling was only slightly worse for the 100

  9. Solar dynamic heat rejection technology. Task 2: Heat pipe radiator development

    NASA Technical Reports Server (NTRS)

    League, Mark; Alario, Joe

    1988-01-01

    This report covers the design, fabrication, and test of several dual slot heat pipe engineering development units. The following dual-slot heat pipes were fabricated and tested: two 6-ft. aluminum heat pipes; a 20-ft. aluminum heat pipe; and a 20-ft. aluminum heat pipe with a four-leg evaporator section. The test results of all four test articles are presented and compared to the performance predicted by the design software. Test results from the four-leg article are incomplete. The methodology for fabricating stainless steel dual slot heat pipes was also studied by performing a tool life test with different single point cutters, and these results are also presented. Although the dual-slot heat pipe has demonstrated the potential to meet the requirements for a high capacity radiator system, uncertainties with the design still exist. The startup difficulties with the aluminum test articles must be solved, and a stainless steel/methanol heat pipe should be built and tested.

  10. Advanced Turbine Systems Program, Conceptual Design and Product Development. Task 6, System definition and analysis

    SciTech Connect

    1995-04-01

    The strategy of the ATS program is to develop a new baseline for industrial gas turbine systems for the 21st century, meeting the buying criteria of industrial gas turbine end users, and having growth potential. These criteria guided the Solar ATS Team in selecting the system definition described in this Topical Report. The key to selecting the ATS system definition was meeting or exceeding each technical goal without negatively impacting other commercial goals. Among the most crucial goals are the buying criteria of the industrial gas turbine market. Solar started by preliminarily considering several cycles with the potential to meet ATS program goals. These candidates were initially narrowed based on a qualitative assessment of several factors such as the potential for meeting program goals and for future growth; the probability of successful demonstration within the program`s schedule and expected level of funding; and the appropriateness of the cycle in light of end users` buying criteria. A first level Quality Function Deployment (QFD) analysis then translated customer needs into functional requirements, and ensured favorable interaction between concept features. Based on this analysis, Solar selected a recuperated cycle as the best approach to fulfilling both D.O.E. and Solar marketing goals. This report details the design and analysis of the selected engine concept, and explains how advanced features of system components achieve program goals. Estimates of cost, performance, emissions and RAMD (reliability, availability, maintainability, durability) are also documented in this report.

  11. CERAMIC MEMBRANE ENABLING TECHNOLOGY FOR IMPROVED IGCC EFFICIENCY

    SciTech Connect

    Ravi Prasad

    2002-11-01

    This quarterly technical progress report will summarize work accomplished for Phase 1 Program during the quarter July to September 2002. In task 1 characterization of PSO1x has shown no decrease in strength at operating temperature. In task 2, composite development has demonstrated the ability to fabricate membranes of the new material PSO1x. In task 3, increased length elements have been fabricated. The work in task 4 testing of PSO1x has demonstrated oxygen purity of greater than 95% after more than 500 hours of testing. In task 5 the multi-element OTM reactor has been operated and produced oxygen at greater than target purity and flux.

  12. Space station data system analysis/architecture study. Task 2: Options development DR-5. Volume 1: Technology options

    NASA Technical Reports Server (NTRS)

    1985-01-01

    The second task in the Space Station Data System (SSDS) Analysis/Architecture Study is the development of an information base that will support the conduct of trade studies and provide sufficient data to make key design/programmatic decisions. This volume identifies the preferred options in the technology category and characterizes these options with respect to performance attributes, constraints, cost, and risk. The technology category includes advanced materials, processes, and techniques that can be used to enhance the implementation of SSDS design structures. The specific areas discussed are mass storage, including space and round on-line storage and off-line storage; man/machine interface; data processing hardware, including flight computers and advanced/fault tolerant computer architectures; and software, including data compression algorithms, on-board high level languages, and software tools. Also discussed are artificial intelligence applications and hard-wire communications.

  13. Development of an aversive Pavlovian-to-instrumental transfer task in rat.

    PubMed

    Campese, Vincent; McCue, Margaret; Lázaro-Muñoz, Gabriel; Ledoux, Joseph E; Cain, Christopher K

    2013-01-01

    Pavlovian-to-instrumental transfer (PIT) is an effect whereby a classically conditioned stimulus (CS) enhances ongoing instrumental responding. PIT has been extensively studied with appetitive conditioning but barely at all with aversive conditioning. Although it's been argued that conditioned suppression is a form of aversive PIT, this effect is fundamentally different from appetitive PIT because the CS suppresses, instead of facilitates, responding. Five experiments investigated the importance of a variety of factors on aversive PIT in a rodent Sidman avoidance paradigm in which ongoing shuttling behavior (unsignaled active avoidance or USAA) was facilitated by an aversive CS. Experiment 1 demonstrated a basic PIT effect. Experiment 2 found that a moderate amount of USAA extinction produces the strongest PIT with shuttling rates best at around 2 responses per minute prior to the CS. Experiment 3 tested a protocol in which the USAA behavior was required to reach the 2-response per minute mark in order to trigger the CS presentation and found that this produced robust and reliable PIT. Experiment 4 found that the Pavlovian conditioning US intensity was not a major determinant of PIT strength. Experiment 5 demonstrated that if the CS and US were not explicitly paired during Pavlovian conditioning, PIT did not occur, showing that CS-US learning is required. Together, these studies demonstrate a robust, reliable and stable aversive PIT effect that is amenable to analysis of neural circuitry.

  14. Technical support for digital systems technology development. Task order 1: ISP contention analysis and control

    NASA Technical Reports Server (NTRS)

    Stehle, Roy H.; Ogier, Richard G.

    1993-01-01

    Alternatives for realizing a packet-based network switch for use on a frequency division multiple access/time division multiplexed (FDMA/TDM) geostationary communication satellite were investigated. Each of the eight downlink beams supports eight directed dwells. The design needed to accommodate multicast packets with very low probability of loss due to contention. Three switch architectures were designed and analyzed. An output-queued, shared bus system yielded a functionally simple system, utilizing a first-in, first-out (FIFO) memory per downlink dwell, but at the expense of a large total memory requirement. A shared memory architecture offered the most efficiency in memory requirements, requiring about half the memory of the shared bus design. The processing requirement for the shared-memory system adds system complexity that may offset the benefits of the smaller memory. An alternative design using a shared memory buffer per downlink beam decreases circuit complexity through a distributed design, and requires at most 1000 packets of memory more than the completely shared memory design. Modifications to the basic packet switch designs were proposed to accommodate circuit-switched traffic, which must be served on a periodic basis with minimal delay. Methods for dynamically controlling the downlink dwell lengths were developed and analyzed. These methods adapt quickly to changing traffic demands, and do not add significant complexity or cost to the satellite and ground station designs. Methods for reducing the memory requirement by not requiring the satellite to store full packets were also proposed and analyzed. In addition, optimal packet and dwell lengths were computed as functions of memory size for the three switch architectures.

  15. Methods Developed by the Tools for Engine Diagnostics Task to Monitor and Predict Rotor Damage in Real Time

    NASA Technical Reports Server (NTRS)

    Baaklini, George Y.; Smith, Kevin; Raulerson, David; Gyekenyesi, Andrew L.; Sawicki, Jerzy T.; Brasche, Lisa

    2003-01-01

    Tools for Engine Diagnostics is a major task in the Propulsion System Health Management area of the Single Aircraft Accident Prevention project under NASA s Aviation Safety Program. The major goal of the Aviation Safety Program is to reduce fatal aircraft accidents by 80 percent within 10 years and by 90 percent within 25 years. The goal of the Propulsion System Health Management area is to eliminate propulsion system malfunctions as a primary or contributing factor to the cause of aircraft accidents. The purpose of Tools for Engine Diagnostics, a 2-yr-old task, is to establish and improve tools for engine diagnostics and prognostics that measure the deformation and damage of rotating engine components at the ground level and that perform intermittent or continuous monitoring on the engine wing. In this work, nondestructive-evaluation- (NDE-) based technology is combined with model-dependent disk spin experimental simulation systems, like finite element modeling (FEM) and modal norms, to monitor and predict rotor damage in real time. Fracture mechanics time-dependent fatigue crack growth and damage-mechanics-based life estimation are being developed, and their potential use investigated. In addition, wireless eddy current and advanced acoustics are being developed for on-wing and just-in-time NDE engine inspection to provide deeper access and higher sensitivity to extend on-wing capabilities and improve inspection readiness. In the long run, these methods could establish a base for prognostic sensing while an engine is running, without any overt actions, like inspections. This damage-detection strategy includes experimentally acquired vibration-, eddy-current- and capacitance-based displacement measurements and analytically computed FEM-, modal norms-, and conventional rotordynamics-based models of well-defined damages and critical mass imbalances in rotating disks and rotors.

  16. Test Plan. GCPS Task 4, subtask 4.2 thrust structure development

    NASA Astrophysics Data System (ADS)

    Greenberg, H. S.

    1994-09-01

    The Single Stage To Orbit (SSTO) vehicle is designed to lift off from a vertical position, go into orbit, return to earth for a horizontal landing, and be reusable for the next mission. (NASA baseline only) In order to meet its performance goals, the SSTO relies on light weight structure and the use of 8 tri-propellant engines. These engines are mounted to the thrust structure. This test plan addresses selection of the material for this structure, and the integrity of the design through testing of elements and a full-scale subcomponent. This test plan supports the development of the design for an advanced composite thrust structure for a Single Stage to Orbit manned, heavy launch vehicle. The thrust structure is designed to transmit very high thrust loads from the engines to the rest of the vehicle (see Figure 1 ). The thrust structure will also be used for primary attachment of the twin vertical tails and possibly act as the aft attach point for the wing. The combination of high loading, high vibration, long service life and high acoustic environments will need to be evaluated by tests. To minimize design risk, a building block approach will be used. We will first screen materials to determine which materials show the most promise for this application. Factors in this screening will be the suitability of these materials for chosen design concepts, particularly concerning specific strength, environmental compatibility and applicability to fabrication processes. Next we will characterize two material systems that will be used in the design; the characterization will allow us to generate preliminary design data that will be used for the analysis. Element testing will be performed to evaluate critical structural locations under load. Final testing on the full scale test article will be performed to verify the design and to demonstrate predictability of the analysis. Additionally, risks associated with fabricating full scale thrust structures will be reduced through

  17. Test Plan. GCPS Task 4, subtask 4.2 thrust structure development

    NASA Technical Reports Server (NTRS)

    Greenberg, H. S.

    1994-01-01

    The Single Stage To Orbit (SSTO) vehicle is designed to lift off from a vertical position, go into orbit, return to earth for a horizontal landing, and be reusable for the next mission. (NASA baseline only) In order to meet its performance goals, the SSTO relies on light weight structure and the use of 8 tri-propellant engines. These engines are mounted to the thrust structure. This test plan addresses selection of the material for this structure, and the integrity of the design through testing of elements and a full-scale subcomponent. This test plan supports the development of the design for an advanced composite thrust structure for a Single Stage to Orbit manned, heavy launch vehicle. The thrust structure is designed to transmit very high thrust loads from the engines to the rest of the vehicle (see Figure 1 ). The thrust structure will also be used for primary attachment of the twin vertical tails and possibly act as the aft attach point for the wing. The combination of high loading, high vibration, long service life and high acoustic environments will need to be evaluated by tests. To minimize design risk, a building block approach will be used. We will first screen materials to determine which materials show the most promise for this application. Factors in this screening will be the suitability of these materials for chosen design concepts, particularly concerning specific strength, environmental compatibility and applicability to fabrication processes. Next we will characterize two material systems that will be used in the design; the characterization will allow us to generate preliminary design data that will be used for the analysis. Element testing will be performed to evaluate critical structural locations under load. Final testing on the full scale test article will be performed to verify the design and to demonstrate predictability of the analysis. Additionally, risks associated with fabricating full scale thrust structures will be reduced through

  18. Conceptual design of a lunar base solar power plant lunar base systems study task 3.3

    NASA Technical Reports Server (NTRS)

    1988-01-01

    The best available concepts for a 100 kW Solar Lunar Power Plant based on static and dynamic conversion concepts have been examined. The two concepts which emerged for direct comparison yielded a difference in delivered mass of 35 MT, the mass equivalent of 1.4 lander payloads, in favor of the static concept. The technologies considered for the various elements are either state-of-the-art or near-term. Two photovoltaic cell concepts should receive high priority for development: i.e., amorphous silicon and indium phosphide cells. The amorphous silicon, because it can be made so light weight and rugged; and the indium phosphide, because it shows very high efficiency potential and is reportedly not degraded by radiation. Also the amorphous silicon cells may be mounted on flexible backing that may roll up much like a carpet for compact storage, delivery, and ease of deployment at the base. The fuel cell and electrolysis cell technology is quite well along for lunar base applications, and because both the Shuttle and the forthcoming Space Station incorporate these devices, the status quo will be maintained. Early development of emerging improvements should be implemented so that essential life verification test programs may commence.

  19. 3-D Art Tasks.

    ERIC Educational Resources Information Center

    Niswander, Virginia

    1983-01-01

    Perceptual motor dysfunctions may not allow children with learning and behavior problems to perform as most children do. A successful art activity for these children is construction using wood scraps. (SR)

  20. Dopamine transporter 3'UTR VNTR genotype is a marker of performance on executive function tasks in children with ADHD

    PubMed Central

    Karama, Sherif; Grizenko, Natalie; Sonuga-Barke, Edmund; Doyle, Alysa; Biederman, Joseph; Mbekou, Valentin; Polotskaia, Anna; Ter-Stepanian, Marina; De Guzman, Rosherrie; Bellingham, Johanne; Sengupta, Sarojini; Joober, Ridha

    2008-01-01

    Background Attention-Deficit/Hyperactivity Disorder (ADHD) is a heterogeneous disorder from both clinical and pathogenic viewpoints. Executive function deficits are considered among the most important pathogenic pathways leading to ADHD and may index part of the heterogeneity in this disorder. Methods To investigate the relationship between the dopamine transporter gene (SLC6A3) 3'-UTR VNTR genotypes and executive function in children with ADHD, 196 children diagnosed with ADHD were sequentially recruited, genotyped, and tested using a battery of three neuropsychological tests aimed at assessing the different aspects of executive functioning. Results Taking into account a correction for multiple comparisons, the main finding of this study is a significant genotype effect on performances on the Tower of London (F = 6.902, p = 0.009) and on the Wechsler Intelligence Scale for Children, Third Edition (WISC-III) Freedom From Distractibility Index (F = 7.125, p = 0.008), as well as strong trends on Self Ordered Pointing Task error scores (F = 4,996 p = 0.026) and WISC-III Digit Span performance (F = 6.28, p = 0.023). Children with the 9/10 genotype exhibited, on average, a poorer performance on all four measures compared to children with the 10/10 genotype. No effect of genotype on Wisconsin Card Sorting Test measures of performance was detected. Conclusion Results are compatible with the view that SLC6A3 genotype may modulate components of executive function performance in children with ADHD. PMID:18559107

  1. Database of Low-E Storm Window Energy Performance across U.S. Climate Zones (Task ET-WIN-PNNL-FY13-01_5.3)

    SciTech Connect

    Cort, Katherine A.; Culp, Thomas D.

    2013-09-01

    This report describes process, assumptions, and modeling results produced in support of the Emerging Technologies Low-e Storm Windows Task 5.3: Create a Database of U.S. Climate-Based Analysis for Low-E Storm Windows. The scope of the overall effort is to develop a database of energy savings and cost effectiveness of low-E storm windows in residential homes across a broad range of U.S. climates using the National Energy Audit Tool (NEAT) and RESFEN model calculations. This report includes a summary of the results, NEAT and RESFEN background, methodology, and input assumptions, and an appendix with detailed results and assumptions by cliamte zone. Both sets of calculation results will be made publicly available through the Building America Solution Center.

  2. TaSK5, an abiotic stress-inducible GSK3/shaggy-like kinase from wheat, confers salt and drought tolerance in transgenic Arabidopsis.

    PubMed

    Christov, Nikolai Kirilov; Christova, Petya Koeva; Kato, Hideki; Liu, Yuelin; Sasaki, Kentaro; Imai, Ryozo

    2014-11-01

    A novel cold-inducible GSK3/shaggy-like kinase, TaSK5, was isolated from winter wheat using a macroarray-based differential screening approach. TaSK5 showed high similarity to Arabidopsis subgroup I GSK3/shaggy-like kinases ASK-alpha, AtSK-gamma and ASK-epsilon. RNA gel blot analyses revealed TaSK5 induction by cold and NaCl treatments and to a lesser extent by drought treatment. TaSK5 functionally complemented the cold- and salt-sensitive phenotypes of a yeast GSK3/shaggy-like kinase mutant, △mck1. Transgenic Arabidopsis plants overexpressing TaSK5 cDNA showed enhanced tolerance to salt and drought stresses. By contrast, the tolerance of the transgenic plants to freezing stress was not altered. Microarray analysis revealed that a number of abiotic stress-inducible genes were constitutively induced in the transgenic Arabidopsis plants, suggesting that TaSK5 may function in a novel signal transduction pathway that appears to be unrelated to DREB1/CBF regulon and may involve crosstalk between abiotic and hormonal signals.

  3. Methods development for measuring and classifying flammability/combustibility of refrigerants. Interim report, Task 1 -- Annotated bibliography and summary

    SciTech Connect

    Heinonen, E.W.; Tapscott, R.E.

    1994-06-01

    For Task 1 of the flammable refrigerant methods development contract, NMERI performed a literature search to identify references on the flammability of refrigerants. A database to store a bibliographic record of the literature search was then developed. This database is contained in the Microsoft Access{reg_sign} relational database management system for Windows{trademark}. Searches for applicable sources were made on-line using the STN{reg_sign} scientific and technical network; off-line using the National Technical Information Service (NTIS) database; WorldCat CD-rom database; the University of New Mexico library search; the Air-Conditioning and Refrigeration institute (ARI) Refrigerant Database; and personal contacts. Three specific areas were searched: refrigerant properties, flammability test methods, and ignition technology. Many of the articles retrieved fall into multiple categories. Ignition technology was included as a separate category because of the importance of the ignition process to flammability and the vast amount of information available on ignition of gaseous fuels, especially hydrocarbons. Over 90 separate references have been entered into the database. Two separate report formats have been developed to display the results of the literature search. Appendix B is the short report format--without abstract, while Appendix C is the long format--with abstract.

  4. Feasibility of developing a portable driver performance data acquisition system for human factors research: Technical tasks. Volume 1

    SciTech Connect

    Carter, R.J.; Barickman, F.S.; Spelt, P.F.; Schmoyer, R.L.; Kirkpatrick, J.R.

    1998-01-01

    A two-phase, multi-year research program entitled ``development of a portable driver performance data acquisition system for human factors research`` was recently completed. The primary objective of the project was to develop a portable data acquisition system for crash avoidance research (DASCAR) that will allow drive performance data to be collected using a large variety of vehicle types and that would be capable of being installed on a given vehicle type within a relatively short-time frame. During phase 1 a feasibility study for designing and fabricating DASCAR was conducted. In phase 2 of the research DASCAR was actually developed and validated. This technical memorandum documents the results from the feasibility study. It is subdivided into three volumes. Volume one (this report) addresses the last five items in the phase 1 research and the first issue in the second phase of the project. Volumes two and three present the related appendices, and the design specifications developed for DASCAR respectively. The six tasks were oriented toward: identifying parameters and measures; identifying analysis tools and methods; identifying measurement techniques and state-of-the-art hardware and software; developing design requirements and specifications; determining the cost of one or more copies of the proposed data acquisition system; and designing a development plan and constructing DASCAR. This report also covers: the background to the program; the requirements for the project; micro camera testing; heat load calculations for the DASCAR instrumentation package in automobile trunks; phase 2 of the research; the DASCAR hardware and software delivered to the National Highway Traffic Safety Administration; and crash avoidance problems that can be addressed by DASCAR.

  5. Development and Demonstration of a Self-Calibrating Pseudolite Array for Task Level Control of a Planetary Rover

    NASA Technical Reports Server (NTRS)

    Rock, Stephen M.; LeMaster, Edward A.

    2001-01-01

    Pseudolites can extend the availability of GPS-type positioning systems to a wide range of applications not possible with satellite-only GPS. One such application is Mars exploration, where the centimeter-level accuracy and high repeatability of CDGPS would make it attractive for rover positioning during autonomous exploration, sample collection, and habitat construction if it were available. Pseudolites distributed on the surface would allow multiple rovers and/or astronauts to share a common navigational reference. This would help enable cooperation for complicated science tasks, reducing the need for instructions from Earth and increasing the likelihood of mission success. Conventional GPS Pseudolite arrays require that the devices be pre-calibrated through a Survey of their locations, typically to sub-centimeter accuracy. This is a problematic task for robots on the surface of another planet. By using the GPS signals that the Pseudolites broadcast, however, it is possible to have the array self-survey its own relative locations, creating a SelfCalibrating Pseudolite Array (SCPA). This requires the use of GPS transceivers instead of standard pseudolites. Surveying can be done either at carrier- or code-phase levels. An overview of SCPA capabilities, system requirements, and self-calibration algorithms is presented in another work. The Aerospace Robotics Laboratory at Statif0id has developed a fully operational prototype SCPA. The array is able to determine the range between any two transceivers with either code- or carrier-phase accuracy, and uses this inter-transceiver ranging to determine the at-ray geometry. This paper presents results from field tests conducted at Stanford University demonstrating the accuracy of inter-transceiver ranging and its viability and utility for array localization, and shows how transceiver motion may be utilized to refine the array estimate by accurately determining carrier-phase integers and line biases. It also summarizes the

  6. Task IV: Development of Circumferential Inlet Distortion through a Representative Eleven Stage High-speed Axial Compressor

    NASA Technical Reports Server (NTRS)

    Tan, Choon-Sooi; Suder, Kenneth (Technical Monitor)

    2003-01-01

    The concepts and the procedure developed in Task I and Task III were used to determine the response of an eleven-stage high-speed compressor to an inlet distortion of 180 deg. circumferential extent for contrasting against its performance under uniform inlet flow. Using the computed results at the inlet to and outlet of the compressor, the computed total pressure ratio and efficiency for the clean condition are determined to be 14.22 and 76.9 percent respectively. As for the distorted case, these are determined to be 10.35 and 71.8 percent respectively, showing deterioration 76.9 percent vs 71.8 percent). The physical consistency of the computed flow field was assessed as a means of demonstrating the applicability and utility of the body force representation for inlet distortion computations. Specifically the computed evolution of the distorted pattern in static pressure and total pressure from compressor inlet to exit is examined. For the eleven-stage compressor examined here, the deterioration in performance has been found to be particularly severe in the last 2 stages. This suggests that the last two stages could be redesigned to alleviate the observed deterioration thus making the compressor performance insensitive to circumferential inlet distortion. This can potentially be accomplished by first determining what should the body force distribution of the last two stages should be to achieve minimal or no deterioration in performance in the last two stages. One can then in principle proceed to determine the blade design to yield such a body force distribution.

  7. 3 CFR 13554 - Executive Order 13554 of October 5, 2010. Establishing the Gulf Coast Ecosystem Restoration Task...

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... defined in 15 CFR 990.30. (e) “Natural Resource Damage Assessment Trustee Council” meansthe designated.... Establishing the Gulf Coast Ecosystem Restoration Task Force 13554 Order 13554 Presidential Documents Executive... Restoration Task Force By the authority vested in me as President by the Constitution and the laws of...

  8. Identifying second language speech tasks and ability levels for successful nurse oral interaction with patients in a linguistic minority setting: an instrument development project.

    PubMed

    Isaacs, Talia; Laurier, Michel D; Turner, Carolyn E; Segalowitz, Norman

    2011-09-01

    One of the most demanding situations for members of linguistic minorities is a conversation between a health professional and a patient, a situation that frequently arises for linguistic minority groups in North America, Europe, and elsewhere. The present study reports on the construction of an oral interaction scale for nurses serving linguistic minorities in their second language (L2). A mixed methods approach was used to identify and validate a set of speech activities relating to nurse interactions with patients and to derive the L2 ability required to carry out those tasks. The research included an extensive literature review, the development of an initial list of speech tasks, and validation of this list with a nurse focus group. The retained speech tasks were then developed into a questionnaire and administered to 133 Quebec nurses who assessed each speech task for difficulty in an L2 context. Results were submitted to Rasch analysis and calibrated with reference to the Canadian Language Benchmarks, and the constructs underlying the speech tasks were identified through exploratory and confirmatory factor analyses. Results showed that speech tasks dealing with emotional aspects of caregiving and conveying health-specific information were reported as being the most demanding in terms of L2 ability, and the most strongly associated with L2 ability required for nurse-patient interactions. Implications are discussed with respect to the development and use of assessment instruments to facilitate L2 workplace training for health care professionals.

  9. Task breakdown

    NASA Technical Reports Server (NTRS)

    Pavlich, Jane

    1990-01-01

    The topics concerning the Center for Space Construction (CSC) space construction breakdown structure are presented in viewgraph form. It is concluded that four components describe a task -- effecting, information gathering, analysis, and regulation; uncertainties effect the relative amount of information gathering and analysis that occurs; and that task timing requirements drive the 'location in time' of cognition.

  10. Final Report on Initial Samples Supplied by LLNL for Task 3.3 Binder Burnout and Sintering Schedule Optimisation

    SciTech Connect

    Walls, P

    1999-01-04

    combination of: (1) use of a higher forming pressure, (2) reduction of organics content, (3) improvement in the distribution of the organic wax and binder components throughout the green body, could possibly alleviate cracking. Ultrasonic emulsification of the binder and wax with a small quantity of water prior to adding to the ball or attrition mill is advised to ensure more even distribution of the wax/binder system. This would also reduce the proportion of organic additives required. The binder burnout stage of the operation must first be optimized (i.e. production of pucks with no cracks) prior to optimization of the sintering stage.

  11. Final report on initial samples supplied by LLNL for task 3.3 binder burnout and sintering schedule optimisation

    SciTech Connect

    Walls, P

    1999-01-04

    combination of: (1) use of a higher forming pressure, (2) reduction of organics content, (3) improvement in the distribution of the organic wax and binder components throughout the green body, could possibly alleviate cracking. Ultrasonic emulsification of the binder and wax with a small quantity of water prior to adding to the ball or attrition mill is advised to ensure more even distribution of the wax/binder system. This would also reduce the proportion of organic additives required.

  12. “Astronomy for a Better World”: IAU/OAD Task Force One Activities to Develop Astronomy Education and Research at Universities in the Developing World

    NASA Astrophysics Data System (ADS)

    Guinan, Edward Francis; Kolenberg, Katrien

    2015-08-01

    The Task Force (1) on Astronomy for Universities & Research (TF-1) was established in 2012 as part of the IAU Office of Astronomy for Development (OAD). This Task Force drives activities related to astronomy education and research at universities mainly in the developing world. Astronomy is used to stimulate research and education in STEM fields and to develop and promote astronomy in regions of the world where there is little or no astronomy. There is also potential for developing research in the historical and cultural aspects of astronomy which may prove important for stimulating an interest in the subject in communities where there is yet no established interest in the science.Since the establishment of the OAD, over 25 TF-1 programs have been funded (or partially funded) to support a wide variety of interesting and innovative astronomy programs in Africa, Asia, South-East Asia, Middle-East, and in South & Central America. Nearly every aspect of development has been supported. These programs include supporting: regional astronomy training schools, specialized workshops, research visits, university twinning programs, distance learning projects, university astronomy curriculum development, as well as small telescope and equipment grants. In addition, a large new program - Astrolab - was introduced (by J-P De Greve and Michele Gerbaldi) to bring starlight” into the class room. In the Astrolab program students carry out and reduce CCD photometry secured by them using remotely controlled telescopes. Results from pilot programs will be discussed.OAD TF-1 programs will be discussed along with future plans for improving and expanding these programs to bring astronomy education and research to a greater number of people and indeed to use Astronomy for a Better World. Information and advice will also be provided about applying for support in the future.

  13. Long-Term Climate Change Assessment Task for the Hanford Site Permanent Isolation Barrier Development Program: Status through FY 1992

    SciTech Connect

    Petersen, K.L.; Chatters, J.C.

    1993-07-01

    The Hanford Site Permanent Isolation Barrier Development Program (Barrier Development Program) was organized (Adams and Wing 1986) to develop the technology needed to provide an in-place disposal capability for the US Department of Energy at the Hanford Site in southeastern Washington. The goals of the Barrier Development Program are to provide defensible evidence that final barrier design(s) will adequately control water infiltration, plant and animal intrusion, and wind and water erosion for a minimum of 1,000 years; to isolate wastes from the accessible environment; and to use markers to warn inadvertent human intruders. Evidence for barrier performance will be obtained by conducting laboratory experiments, field tests, computer modeling, and other studies that establish confidence in the barrier`s ability to meet its 1,000-year design life. The performance and stability of natural barrier analogs that have existed for several millennia and the reconstruction of climate changes during the past 10,000 to 125,000 years also will provide insight into bounding conditions of possible future changes and increase confidence in the barriers design. In the following discussion the term {open_quotes}long-term{close_quotes} references periods of time up to 1000`s of years, distinguishing it from {open_quotes}short-term{close_quotes} weather patterns covering a decade or less. Specific activities focus on planning and conducting a series of studies and tests required to confirm key aspects of the barrier design. The effort is a collaborative one between scientists and engineers from Westinghouse Hanford Company (Westinghouse Hanford) and Pacific Northwest Laboratory (PNL) to design barriers to limit movement of radionuclides and other contaminants to the accessible environment for at least 1,000 years. These activities have been divided into 14 groups of tasks that aid in the complete development of protective barrier and warning marker system.

  14. Independent effects of 2-D and 3-D locations of stimuli in a 3-D display on response speed in a Simon task

    PubMed Central

    Umemura, Hiroyuki

    2015-01-01

    The Simon Effect is a phenomenon in which reaction times are usually faster when the stimulus location and the response correspond, even if the stimulus location is irrelevant to the task. Recent studies have demonstrated the Simon effect in a three-dimensional (3-D) display. The present study examined whether two-dimensional (2-D) and 3-D locations simultaneously affected the Simon effect for stimuli in which a target and fixation were located on the same plane (ground or ceiling) at different 3-D depths, and the perspective effect produced a difference in the 2-D vertical location of the target stimulus relative to the fixation. The presence of the ground and ceiling plane was controlled to examine the contextual effects of background. The results showed that the 2-D vertical location and 3-D depth simultaneously affected the speed of responses, and they did not interact. The presence of the background did not affect the magnitude of either the 2-D or the 3-D Simon effect. These results suggest that 2-D vertical location and 3-D depth are coded simultaneously and independently, and both affect response selection in which 2-D and 3-D representations overlap. PMID:26388807

  15. Dopamine D3 Receptors Modulate the Ability of Win-Paired Cues to Increase Risky Choice in a Rat Gambling Task.

    PubMed

    Barrus, Michael M; Winstanley, Catharine A

    2016-01-20

    Similar to other addiction disorders, the cues inherent in many gambling procedures are thought to play an important role in mediating their addictive nature. Animal models of gambling-related behavior, while capturing dimensions of economic decision making, have yet to address the impact that these salient cues may have in promoting maladaptive choice. Here, we determined whether adding win-associated audiovisual cues to a rat gambling task (rGT) would influence decision making. Thirty-two male Long-Evans rats were tested on either the cued or uncued rGT. In these tasks, animals chose between four options associated with different magnitudes and frequencies of reward and punishing time-out periods. As in the Iowa Gambling Task, favoring options associated with smaller per-trial rewards but smaller losses and avoiding the tempting "high-risk, high-reward" decks maximized profits. Although the reinforcement contingencies were identical in both task versions, rats' choice of the disadvantageous risky options was significantly greater on the cued task. Furthermore, a D3 receptor agonist increased choice of the disadvantageous options, whereas a D3 antagonist had the opposite effects, only on the cued task. These findings are consistent with the reported role of D3 receptors in mediating the facilitatory effects of cues in addiction. Collectively, these results indicate that the cued rGT is a valuable model with which to study the mechanism by which salient cues can invigorate maladaptive decision making, an important and understudied component of both gambling and substance use disorders. Significance statement: We used a rodent analog of the Iowa Gambling Task to determine whether the addition of audiovisual cues would affect choice preferences. Adding reward-concurrent cues significantly increased risky choice. This is the first clear demonstration that reward-paired cues can bias cost/benefit decision making against a subject's best interests in a manner concordant

  16. Dopamine D3 Receptors Modulate the Ability of Win-Paired Cues to Increase Risky Choice in a Rat Gambling Task.

    PubMed

    Barrus, Michael M; Winstanley, Catharine A

    2016-01-20

    Similar to other addiction disorders, the cues inherent in many gambling procedures are thought to play an important role in mediating their addictive nature. Animal models of gambling-related behavior, while capturing dimensions of economic decision making, have yet to address the impact that these salient cues may have in promoting maladaptive choice. Here, we determined whether adding win-associated audiovisual cues to a rat gambling task (rGT) would influence decision making. Thirty-two male Long-Evans rats were tested on either the cued or uncued rGT. In these tasks, animals chose between four options associated with different magnitudes and frequencies of reward and punishing time-out periods. As in the Iowa Gambling Task, favoring options associated with smaller per-trial rewards but smaller losses and avoiding the tempting "high-risk, high-reward" decks maximized profits. Although the reinforcement contingencies were identical in both task versions, rats' choice of the disadvantageous risky options was significantly greater on the cued task. Furthermore, a D3 receptor agonist increased choice of the disadvantageous options, whereas a D3 antagonist had the opposite effects, only on the cued task. These findings are consistent with the reported role of D3 receptors in mediating the facilitatory effects of cues in addiction. Collectively, these results indicate that the cued rGT is a valuable model with which to study the mechanism by which salient cues can invigorate maladaptive decision making, an important and understudied component of both gambling and substance use disorders. Significance statement: We used a rodent analog of the Iowa Gambling Task to determine whether the addition of audiovisual cues would affect choice preferences. Adding reward-concurrent cues significantly increased risky choice. This is the first clear demonstration that reward-paired cues can bias cost/benefit decision making against a subject's best interests in a manner concordant

  17. High School Students' Career Decision-Making Process: Development and Validation of the Study Choice Task Inventory

    ERIC Educational Resources Information Center

    Germeijs, Veerle; Verschueren, Karine

    2006-01-01

    During adolescence, one important career-related decision is the choice of a study in higher education. In this article, a new set of measures for different tasks (i.e., orientation, exploration, commitment) that can be distinguished during this career decision-making process was constructed: the Study Choice Task Inventory (SCTI). A sample of 946…

  18. Toward the Development of an Observation Measure of Interest and Attention for Literacy Tasks in Kindergarten Students

    ERIC Educational Resources Information Center

    Coughlan, Kelly A.

    2012-01-01

    Kindergarten students (N = 95) in three schools and seven classrooms were observed for on-task versus off-task behavior during three literacy instruction opportunities; small group instruction, whole group instruction and the less structured library setting over the 2011-2012 school year. Students' early literacy skills were assessed before…

  19. The Development of a General Associative Learning Account of Skill Acquisition in a Relative Arrival-Time Judgment Task

    ERIC Educational Resources Information Center

    Loft, Shayne; Neal, Andrew; Humphreys, Michael S.

    2007-01-01

    Current theory assumes that individuals only use information from the immediate environment to perform relative arrival-time judgment tasks. This article presents a theoretical analysis of the memory requirements of this task. The authors present an analysis of the inputs to the memory system and the processes that map those inputs onto outputs.…

  20. 3-DTV research and development in Europe

    NASA Astrophysics Data System (ADS)

    Sand, Ruediger

    1991-08-01

    An overview on the state of the art of 3-DTV in Europe is given, and the new European Co- operation in the Field of Scientific and Technical Research (COST) project and its objectives are described. The paper starts with a report on 3-DTV broadcast transmissions in 1982 using the simple anaglyph technique, which in many European countries found enthusiastic public interest. Following that, in three international audio and video fairs in 1983, 1985, and 1987 in Berlin, presentations of a high-quality two-channel 3-DTV system using large screen projection, showing professionally produced demonstration programs, attracted about 50,000 visitors. Meanwhile, several 3-DTV activities for advertising, information, and special applications such as medical imaging are to be found. In the broadcast domain, research and development aim to transmit 3-DTV within a high-definition TV channel.

  1. 3D Visualization Development of SIUE Campus

    NASA Astrophysics Data System (ADS)

    Nellutla, Shravya

    Geographic Information Systems (GIS) has progressed from the traditional map-making to the modern technology where the information can be created, edited, managed and analyzed. Like any other models, maps are simplified representations of real world. Hence visualization plays an essential role in the applications of GIS. The use of sophisticated visualization tools and methods, especially three dimensional (3D) modeling, has been rising considerably due to the advancement of technology. There are currently many off-the-shelf technologies available in the market to build 3D GIS models. One of the objectives of this research was to examine the available ArcGIS and its extensions for 3D modeling and visualization and use them to depict a real world scenario. Furthermore, with the advent of the web, a platform for accessing and sharing spatial information on the Internet, it is possible to generate interactive online maps. Integrating Internet capacity with GIS functionality redefines the process of sharing and processing the spatial information. Enabling a 3D map online requires off-the-shelf GIS software, 3D model builders, web server, web applications and client server technologies. Such environments are either complicated or expensive because of the amount of hardware and software involved. Therefore, the second objective of this research was to investigate and develop simpler yet cost-effective 3D modeling approach that uses available ArcGIS suite products and the free 3D computer graphics software for designing 3D world scenes. Both ArcGIS Explorer and ArcGIS Online will be used to demonstrate the way of sharing and distributing 3D geographic information on the Internet. A case study of the development of 3D campus for the Southern Illinois University Edwardsville is demonstrated.

  2. Final Report of the Minority Role Stereotyping Sub-Task Force of the State Superintendent's Task Force on "Freedom for Individual Development: Role Stereotyping in Wisconsin's Schools."

    ERIC Educational Resources Information Center

    Wisconsin State Dept. of Public Instruction, Madison.

    This report consists of: (1) a description of role stereotyping and its effects on public instruction; and (2) guidelines and resources for the development of a plan to combat role stereotyping. Appendices include numerous sample forms and questionnaires, recommendations, checklists, and evaluation guidelines that might be used in an action plan…

  3. NSI security task: Overview

    NASA Technical Reports Server (NTRS)

    Tencati, Ron

    1991-01-01

    An overview is presented of the NASA Science Internet (NSI) security task. The task includes the following: policies and security documentation; risk analysis and management; computer emergency response team; incident handling; toolkit development; user consulting; and working groups, conferences, and committees.

  4. Vitamin D3 and brain development.

    PubMed

    Eyles, D; Brown, J; Mackay-Sim, A; McGrath, J; Feron, F

    2003-01-01

    Evidence for the presence of the vitamin D receptor in brain implies this vitamin may have some function in this organ. This study investigates whether vitamin D(3) acts during brain development. We demonstrate that rats born to vitamin D(3)-deficient mothers had profound alterations in the brain at birth. The cortex was longer but not wider, the lateral ventricles were enlarged, the cortex was proportionally thinner and there was more cell proliferation throughout the brain. There were reductions in brain content of nerve growth factor and glial cell line-derived neurotrophic factor and reduced expression of p75(NTR), the low-affinity neurotrophin receptor. Our findings would suggest that low maternal vitamin D(3) has important ramifications for the developing brain. PMID:12710973

  5. Do Rare Stimuli Evoke Large P3s by Being Unexpected? A Comparison of Oddball Effects Between Standard-Oddball and Prediction-Oddball Tasks

    PubMed Central

    Verleger, Rolf; Śmigasiewicz, Kamila

    2016-01-01

    The P3 component of event-related potentials increases when stimuli are rarely presented. It has been assumed that this oddball effect (rare-frequent difference) reflects the unexpectedness of rare stimuli. The assumption of unexpectedness and its link to P3 amplitude were tested here. A standard- oddball task requiring alternative key-press responses to frequent and rare stimuli was compared with an oddball-prediction task where stimuli had to be first predicted and then confirmed by key-pressing. Oddball effects in the prediction task depended on whether the frequent or the rare stimulus had been predicted. Oddball effects on P3 amplitudes and error rates in the standard oddball task closely resembled effects after frequent predictions. This corroborates the notion that these effects occur because frequent stimuli are expected and rare stimuli are unexpected. However, a closer look at the prediction task put this notion into doubt because the modifications of oddball effects on P3 by expectancies were entirely due to effects on frequent stimuli, whereas the large P3 amplitudes evoked by rare stimuli were insensitive to predictions (unlike response times and error rates). Therefore, rare stimuli cannot be said to evoke large P3 amplitudes because they are unexpected. We discuss these diverging effects of frequency and expectancy, as well as general differences between tasks, with respect to concepts and hypotheses about P3b’s function and conclude that each discussed concept or hypothesis encounters some problems, with a conception in terms of subjective relevance assigned to stimuli offering the most consistent account of these basic effects. PMID:27512527

  6. Space Radiation Transport Code Development: 3DHZETRN

    NASA Technical Reports Server (NTRS)

    Wilson, John W.; Slaba, Tony C.; Badavi, Francis F.; Reddell, Brandon D.; Bahadori, Amir A.

    2015-01-01

    The space radiation transport code, HZETRN, has been used extensively for research, vehicle design optimization, risk analysis, and related applications. One of the simplifying features of the HZETRN transport formalism is the straight-ahead approximation, wherein all particles are assumed to travel along a common axis. This reduces the governing equation to one spatial dimension allowing enormous simplification and highly efficient computational procedures to be implemented. Despite the physical simplifications, the HZETRN code is widely used for space applications and has been found to agree well with fully 3D Monte Carlo simulations in many circumstances. Recent work has focused on the development of 3D transport corrections for neutrons and light ions (Z < 2) for which the straight-ahead approximation is known to be less accurate. Within the development of 3D corrections, well-defined convergence criteria have been considered, allowing approximation errors at each stage in model development to be quantified. The present level of development assumes the neutron cross sections have an isotropic component treated within N explicit angular directions and a forward component represented by the straight-ahead approximation. The N = 1 solution refers to the straight-ahead treatment, while N = 2 represents the bi-directional model in current use for engineering design. The figure below shows neutrons, protons, and alphas for various values of N at locations in an aluminum sphere exposed to a solar particle event (SPE) spectrum. The neutron fluence converges quickly in simple geometry with N > 14 directions. The improved code, 3DHZETRN, transports neutrons, light ions, and heavy ions under space-like boundary conditions through general geometry while maintaining a high degree of computational efficiency. A brief overview of the 3D transport formalism for neutrons and light ions is given, and extensive benchmarking results with the Monte Carlo codes Geant4, FLUKA, and

  7. The Level/Preventive Approach to Solving Technical and Economic Tasks as One of Directions in Development of the Enterprises of Oil Refining and Petrochemical Industry

    NASA Astrophysics Data System (ADS)

    Damineva, R.; Daminev, R.; Karimov, O.

    2016-06-01

    In this work, as a tool of strategy generation in development of industrial enterprise, a methodological approach is considered, that allows the choosing the best path of development among many solutions of technical and economic tasks, taking into account both the interests of enterprises and of society as a whole.

  8. Supplement to Task Force Report on Rural Development Research in the Northeast for the Next Five Years--A Framework. Publication 1.

    ERIC Educational Resources Information Center

    Harrington, Clifford R., Comp.; Glock, Sandra, Comp.

    Prepared by the Task Force on Rural Development Research (appointed by the U.S. Department of Agriculture), this analytical directory gives primary emphasis to 133 Rural Development 1 (RD1) research projects which were "active" projects between January 1 and June 30, 1973 in 13 Northeastern state agricultural experiment stations and the 2…

  9. Evaluating Maintenance Performance: The Development and Tryout of Criterion Referenced Job Task Performance Tests for Electronic Maintenance. Final Report for Period January 1969-May 1974.

    ERIC Educational Resources Information Center

    Shriver, Edgar L.; Foley, John P., Jr.

    A battery of criterion referenced job task performance tests (JIPT) for typical electronic maintenance activities were developed. The construction of a battery of such tests together with an appropriate scoring for reporting the results is detailed. The development of a Test Administrators Handbook also is described. This battery is considered to…

  10. Older Women's Development: A Comparison of Women in Their 60s and 80s on a Measure of Erikson's Developmental Tasks.

    ERIC Educational Resources Information Center

    Norman, Suzanne M.; McCluskey-Fawcett, Kathleen; Ashcraft, Lisa

    2002-01-01

    Compares women from two ages groups in order to understand their development across the life span. Measures of Psychosocial Development, which assesses Erikson's developmental stages, were administered to 41 women in 2 cohorts (ages 60-70, ages 80-90). Age group differences in the resolution of Erikson's identity and trust developmental tasks were…

  11. Final Report, Materials for Industrial Heat Recovery Systems, Tasks 3 and 4 Materials for Heat Recovery in Recovery Boilers

    SciTech Connect

    Keiser, James R.; Kish, Joseph R.; Singh, Preet M.; Sarma, Gorti B.; Yuan, Jerry; Gorog, J. Peter; Frederick, Laurie A.; Jette, Francois R.; Meisner, Roberta A.; Singbeil, Douglas L.

    2007-12-31

    tubes. Also, these fluctuating air flow patterns can result in deposition of black liquor on the wall tubes, and during periods when deposition is high, there is a noticeable increase in the concentrations of sulfur-bearing gases like hydrogen sulfide and methyl mercaptan. Laboratory studies have shown that chromized and aluminized surface treatments on carbon steel improve the resistance to sulfidation attack. Studies of superheater corrosion and cracking have included laboratory analyses of cracked tubes, laboratory corrosion studies designed to simulate the superheater environment and field tests to study the movement of superheater tubes and to expose a corrosion probe to assess the corrosion behavior of alternate superheater alloys, particularly alloys that would be used for superheaters operating at higher temperatures and higher pressures than most current boilers. In the laboratory corrosion studies, samples of six alternate materials were immersed in an aggressive, low melting point salt mixture and exposed for times up to 336 h, at temperatures of 510, 530 or 560°C in an inert or reactive cover gas. Using weight change and results of metallographic examination, the samples were graded on their resistance to the various environments. For the superheater corrosion probe studies, samples of the same six materials were exposed on an air-cooled corrosion probe exposed in the superheater section of a recovery boiler for 1000 h. Post exposure examination showed cracking and/or subsurface attack in the samples exposed at the higher temperatures with the attack being more severe for samples 13 exposed above the first melting temperature of the deposits that collected on the superheater tubes. From these superheater studies, a ranking was developed for the six materials tested. The task addressing cracking and corrosion of primary air port tubes that was part of this project produced results that have been extensively implemented in recovery boilers in North America

  12. A Comparative Analysis of 2D and 3D Tasks for Virtual Reality Therapies Based on Robotic-Assisted Neurorehabilitation for Post-stroke Patients.

    PubMed

    Lledó, Luis D; Díez, Jorge A; Bertomeu-Motos, Arturo; Ezquerro, Santiago; Badesa, Francisco J; Sabater-Navarro, José M; García-Aracil, Nicolás

    2016-01-01

    Post-stroke neurorehabilitation based on virtual therapies are performed completing repetitive exercises shown in visual electronic devices, whose content represents imaginary or daily life tasks. Currently, there are two ways of visualization of these task. 3D virtual environments are used to get a three dimensional space that represents the real world with a high level of detail, whose realism is determinated by the resolucion and fidelity of the objects of the task. Furthermore, 2D virtual environments are used to represent the tasks with a low degree of realism using techniques of bidimensional graphics. However, the type of visualization can influence the quality of perception of the task, affecting the patient's sensorimotor performance. The purpose of this paper was to evaluate if there were differences in patterns of kinematic movements when post-stroke patients performed a reach task viewing a virtual therapeutic game with two different type of visualization of virtual environment: 2D and 3D. Nine post-stroke patients have participated in the study receiving a virtual therapy assisted by PUPArm rehabilitation robot. Horizontal movements of the upper limb were performed to complete the aim of the tasks, which consist in reaching peripheral or perspective targets depending on the virtual environment shown. Various parameter types such as the maximum speed, reaction time, path length, or initial movement are analyzed from the data acquired objectively by the robotic device to evaluate the influence of the task visualization. At the end of the study, a usability survey was provided to each patient to analysis his/her satisfaction level. For all patients, the movement trajectories were enhanced when they completed the therapy. This fact suggests that patient's motor recovery was increased. Despite of the similarity in majority of the kinematic parameters, differences in reaction time and path length were higher using the 3D task. Regarding the success rates

  13. A Comparative Analysis of 2D and 3D Tasks for Virtual Reality Therapies Based on Robotic-Assisted Neurorehabilitation for Post-stroke Patients.

    PubMed

    Lledó, Luis D; Díez, Jorge A; Bertomeu-Motos, Arturo; Ezquerro, Santiago; Badesa, Francisco J; Sabater-Navarro, José M; García-Aracil, Nicolás

    2016-01-01

    Post-stroke neurorehabilitation based on virtual therapies are performed completing repetitive exercises shown in visual electronic devices, whose content represents imaginary or daily life tasks. Currently, there are two ways of visualization of these task. 3D virtual environments are used to get a three dimensional space that represents the real world with a high level of detail, whose realism is determinated by the resolucion and fidelity of the objects of the task. Furthermore, 2D virtual environments are used to represent the tasks with a low degree of realism using techniques of bidimensional graphics. However, the type of visualization can influence the quality of perception of the task, affecting the patient's sensorimotor performance. The purpose of this paper was to evaluate if there were differences in patterns of kinematic movements when post-stroke patients performed a reach task viewing a virtual therapeutic game with two different type of visualization of virtual environment: 2D and 3D. Nine post-stroke patients have participated in the study receiving a virtual therapy assisted by PUPArm rehabilitation robot. Horizontal movements of the upper limb were performed to complete the aim of the tasks, which consist in reaching peripheral or perspective targets depending on the virtual environment shown. Various parameter types such as the maximum speed, reaction time, path length, or initial movement are analyzed from the data acquired objectively by the robotic device to evaluate the influence of the task visualization. At the end of the study, a usability survey was provided to each patient to analysis his/her satisfaction level. For all patients, the movement trajectories were enhanced when they completed the therapy. This fact suggests that patient's motor recovery was increased. Despite of the similarity in majority of the kinematic parameters, differences in reaction time and path length were higher using the 3D task. Regarding the success rates

  14. A Comparative Analysis of 2D and 3D Tasks for Virtual Reality Therapies Based on Robotic-Assisted Neurorehabilitation for Post-stroke Patients

    PubMed Central

    Lledó, Luis D.; Díez, Jorge A.; Bertomeu-Motos, Arturo; Ezquerro, Santiago; Badesa, Francisco J.; Sabater-Navarro, José M.; García-Aracil, Nicolás

    2016-01-01

    Post-stroke neurorehabilitation based on virtual therapies are performed completing repetitive exercises shown in visual electronic devices, whose content represents imaginary or daily life tasks. Currently, there are two ways of visualization of these task. 3D virtual environments are used to get a three dimensional space that represents the real world with a high level of detail, whose realism is determinated by the resolucion and fidelity of the objects of the task. Furthermore, 2D virtual environments are used to represent the tasks with a low degree of realism using techniques of bidimensional graphics. However, the type of visualization can influence the quality of perception of the task, affecting the patient's sensorimotor performance. The purpose of this paper was to evaluate if there were differences in patterns of kinematic movements when post-stroke patients performed a reach task viewing a virtual therapeutic game with two different type of visualization of virtual environment: 2D and 3D. Nine post-stroke patients have participated in the study receiving a virtual therapy assisted by PUPArm rehabilitation robot. Horizontal movements of the upper limb were performed to complete the aim of the tasks, which consist in reaching peripheral or perspective targets depending on the virtual environment shown. Various parameter types such as the maximum speed, reaction time, path length, or initial movement are analyzed from the data acquired objectively by the robotic device to evaluate the influence of the task visualization. At the end of the study, a usability survey was provided to each patient to analysis his/her satisfaction level. For all patients, the movement trajectories were enhanced when they completed the therapy. This fact suggests that patient's motor recovery was increased. Despite of the similarity in majority of the kinematic parameters, differences in reaction time and path length were higher using the 3D task. Regarding the success rates

  15. A Comparative Analysis of 2D and 3D Tasks for Virtual Reality Therapies Based on Robotic-Assisted Neurorehabilitation for Post-stroke Patients

    PubMed Central

    Lledó, Luis D.; Díez, Jorge A.; Bertomeu-Motos, Arturo; Ezquerro, Santiago; Badesa, Francisco J.; Sabater-Navarro, José M.; García-Aracil, Nicolás

    2016-01-01

    Post-stroke neurorehabilitation based on virtual therapies are performed completing repetitive exercises shown in visual electronic devices, whose content represents imaginary or daily life tasks. Currently, there are two ways of visualization of these task. 3D virtual environments are used to get a three dimensional space that represents the real world with a high level of detail, whose realism is determinated by the resolucion and fidelity of the objects of the task. Furthermore, 2D virtual environments are used to represent the tasks with a low degree of realism using techniques of bidimensional graphics. However, the type of visualization can influence the quality of perception of the task, affecting the patient's sensorimotor performance. The purpose of this paper was to evaluate if there were differences in patterns of kinematic movements when post-stroke patients performed a reach task viewing a virtual therapeutic game with two different type of visualization of virtual environment: 2D and 3D. Nine post-stroke patients have participated in the study receiving a virtual therapy assisted by PUPArm rehabilitation robot. Horizontal movements of the upper limb were performed to complete the aim of the tasks, which consist in reaching peripheral or perspective targets depending on the virtual environment shown. Various parameter types such as the maximum speed, reaction time, path length, or initial movement are analyzed from the data acquired objectively by the robotic device to evaluate the influence of the task visualization. At the end of the study, a usability survey was provided to each patient to analysis his/her satisfaction level. For all patients, the movement trajectories were enhanced when they completed the therapy. This fact suggests that patient's motor recovery was increased. Despite of the similarity in majority of the kinematic parameters, differences in reaction time and path length were higher using the 3D task. Regarding the success rates

  16. LNG Safety Research: FEM3A Model Development

    SciTech Connect

    Iraj A. Salehi; Jerry Havens; Tom Spicer

    2006-09-30

    The initial scope of work for this project included: (1) Improving the FEM3A advanced turbulence closure module, (2) Adaptation of FEM3A for more general applications, and (3) Verification of dispersion over rough surfaces, with and without obstacle using the advanced turbulence closure module. These work elements were to be performed by Chemical Hazards Research Center (CHRC), Department of Chemical Engineering, University of Arkansas as a subcontractor to Gas Technology Institute (GTI). The tasks for GTI included establishment of the scientific support base for standardization of the FEM3A model, project management, technology transfer, and project administration. Later in the course of the project, the scope of work was modified by the National Energy Technology Laboratories (NETL) to remove the emphasis on FEM3A model and instead, develop data in support of NETL's FLUENT modeling. With this change, GTI was also instructed to cease activities relative to FEM3A model. GTI's technical activities through this project included the initial verification of FEM3A model, provision of technical inputs to CHRC researchers regarding the structure of the final product, and participation in technical discussion sessions with CHRC and NETL technical staff. GTI also began the development of a Windows-based front end for the model but the work was stopped due to the change in scope of work. In the meantime, GTI organized a workshop on LNG safety in Houston, Texas. The workshop was very successful and 75 people from various industries participated. All technical objectives were met satisfactorily by Dr. Jerry Havens and Dr. Tom Spicer of CHRC and results are presented in a stand-alone report included as Appendix A to this report.

  17. LNG Safety Research: FEM3A Model Development

    SciTech Connect

    2006-09-30

    The initial scope of work for this project included: 1) Improving the FEM3A advanced turbulence closure module, 2) Adaptation of FEM3A for more general applications, and 3) Verification of dispersion over rough surfaces, with and without obstacle using the advanced turbulence closure module. These work elements were to be performed by Chemical Hazards Research Center (CHRC), Department of Chemical Engineering, University of Arkansas as a subcontractor to Gas Technology Institute (GTI). The tasks for GTI included establishment of the scientific support base for standardization of the FEM3A model, project management, technology transfer, and project administration. Later in the course of the project, the scope of work was modified by the National Energy Technology Laboratories (NETL) to remove the emphasis on FEM3A model and instead, develop data in support of NETL’s FLUENT modeling. With this change, GTI was also instructed to cease activities relative to FEM3A model. GTI’s technical activities through this project included the initial verification of FEM3A model, provision of technical inputs to CHRC researchers regarding the structure of the final product, and participation in technical discussion sessions with CHRC and NETL technical staff. GTI also began the development of a Windows-based front end for the model but the work was stopped due to the change in scope of work. In the meantime, GTI organized a workshop on LNG safety in Houston, Texas. The workshop was very successful and 75 people from various industries participated. All technical objectives were met satisfactorily by Dr. Jerry Havens and Dr. Tom Spicer of CHRC and results are presented in a stand-alone report included as Appendix A to this report.

  18. FNAS/summer faculty fellowship research continuation program. Task 6: Integrated model development for liquid fueled rocket propulsion systems. Task 9: Aspects of model-based rocket engine condition monitoring and control

    NASA Technical Reports Server (NTRS)

    Santi, L. Michael; Helmicki, Arthur J.

    1993-01-01

    The objective of Phase I of this research effort was to develop an advanced mathematical-empirical model of SSME steady-state performance. Task 6 of Phase I is to develop component specific modification strategy for baseline case influence coefficient matrices. This report describes the background of SSME performance characteristics and provides a description of the control variable basis of three different gains models. The procedure used to establish influence coefficients for each of these three models is also described. Gains model analysis results are compared to Rocketdyne's power balance model (PBM).

  19. NUBEAM developments and 3d halo modeling

    NASA Astrophysics Data System (ADS)

    Gorelenkova, M. V.; Medley, S. S.; Kaye, S. M.

    2012-10-01

    Recent developments related to the 3D halo model in NUBEAM code are described. To have a reliable halo neutral source for diagnostic simulation, the TRANSP/NUBEAM code has been enhanced with full implementation of ADAS atomic physic ground state and excited state data for hydrogenic beams and mixed species plasma targets. The ADAS codes and database provide the density and temperature dependence of the atomic data, and the collective nature of the state excitation process. To be able to populate 3D halo output with sufficient statistical resolution, the capability to control the statistics of fast ion CX modeling and for thermal halo launch has been added to NUBEAM. The 3D halo neutral model is based on modification and extension of the ``beam in box'' aligned 3d Cartesian grid that includes the neutral beam itself, 3D fast neutral densities due to CX of partially slowed down fast ions in the beam halo region, 3D thermal neutral densities due to CX deposition and fast neutral recapture source. More details on the 3D halo simulation design will be presented.

  20. Advanced turbine systems program conceptual design and product development task 5 -- market study of the gas fired ATS. Topical report

    SciTech Connect

    1995-05-01

    Solar Turbines Incorporated (Solar), in partnership with the Department of Energy, will develop a family of advanced gas turbine-based power systems (ATS) for widespread commercialization within the domestic and international industrial marketplace, and to the rapidly changing electric power generation industry. The objective of the jointly-funded Program is to introduce an ATS with high efficiency, and markedly reduced emissions levels, in high numbers as rapidly as possible following introduction. This Topical Report is submitted in response to the requirements outlined in Task 5 of the Department of Energy METC Contract on Advanced Combustion Systems, Contract No, DE AC21-93MC30246 (Contract), for a Market Study of the Gas Fired Advanced Turbine System. It presents a market study for the ATS proposed by Solar, and will examine both the economic and siting constraints of the ATS compared with competing systems in the various candidate markets. Also contained within this report is an examination and analysis of Solar`s ATS and its ability to compete in future utility and industrial markets, as well as factors affecting the marketability of the ATS.