Science.gov

Sample records for 325 mesh coal

  1. Urea injection NO sub X removal on a 325 MW brown coal-fired electric utility boiler in West Germany

    SciTech Connect

    Negrea, S.; Jones, D.G. ); Rose, G. ); Smith, R.A.; Shimoto, G.H. )

    1990-01-01

    An advanced urea injection system for NO{sub x} control has been installed and is providing compliance with 200 mg/Nm3 (i.e., about 100 ppm) regulatory requirements on a 325 MW brown coal-fired Block C Offleben boiler operated by Braunschweigische Kohlen-Bergwerke AG (BKB), a Wester German electric utility company. The boiler is part of BKB's Offleben plant, located near Hannover on the border with East Germany. This paper concludes that proper urea injection system design (i.e., injection nozzle parameters and nozzle locations), combined with proper operation and adjustment of automatic load-following control, has provided BKB with a reliable means of compliance with NO{sub x} control regulations. Of particular importance in this application was achieving low levels of NH{sub 3} slip, which would have otherwise combined with sulfur oxides, causing deposits and/or air preheater fouling.

  2. Micronized coal solves mushroom grower's boiler headaches

    SciTech Connect

    Reason, J.

    1984-03-01

    A brief account is given of a Utah mushroom grower who has replaced two underfeed stoker-fired boilers requiring 7 attendants by an ultra-fine pulverised coal-fired system. The coal is ground in a proprietary rotary grinder to 80% through a 325-mesh screen. Information is presented on the mill and the special refractory burners required.

  3. 30 CFR 75.325 - Air quantity.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working...

  4. 30 CFR 75.325 - Air quantity.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working...

  5. 30 CFR 75.325 - Air quantity.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working...

  6. 30 CFR 75.325 - Air quantity.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working...

  7. 30 CFR 75.325 - Air quantity.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Air quantity. 75.325 Section 75.325 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.325 Air quantity. (a)(1) In bituminous and lignite mines the quantity of air shall be at least 3,000 cubic feet per minute reaching each working...

  8. 40 CFR 98.325 - Procedures for estimating missing data.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 21 2011-07-01 2011-07-01 false Procedures for estimating missing data. 98.325 Section 98.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Underground Coal Mines § 98.325 Procedures...

  9. 40 CFR 98.325 - Procedures for estimating missing data.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 22 2012-07-01 2012-07-01 false Procedures for estimating missing data. 98.325 Section 98.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Underground Coal Mines § 98.325 Procedures...

  10. 40 CFR 98.325 - Procedures for estimating missing data.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 21 2014-07-01 2014-07-01 false Procedures for estimating missing data. 98.325 Section 98.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Underground Coal Mines § 98.325 Procedures...

  11. 40 CFR 98.325 - Procedures for estimating missing data.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 22 2013-07-01 2013-07-01 false Procedures for estimating missing data. 98.325 Section 98.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Underground Coal Mines § 98.325 Procedures...

  12. Correlation of stability/rheology relationship with coal properties and chemical additives

    SciTech Connect

    Ohene, F.

    1990-01-01

    A methodology has been developed in order to determine the influence of individual particle size fractions on coal water slurry rheology. This involves the determination of the packaging concentrations and rheology of the separate particle size fractions; {minus}400 mesh, {minus}400/325, {minus}325/270, {minus}270/200 mesh, {minus}200/140 mesh, {minus}140/100 mesh and {minus}100/80 mesh as a function of solids loading. The packaging concentrations of the separate particle size fractions and that of several blends of these sizes have been determined. The packaging concentrations were determined from particle size distribution measurements and a program based on truncated log-normal distribution which has been developed at the Adelphi Center for Energy Studies. 5 refs., 7 figs., 10 tabs.

  13. Pelletizing/reslurrying as a means of distributing and firing clean coal

    SciTech Connect

    Conkle, H.N.

    1992-03-17

    The objective of this study is to develop technology that permits the practical and economic preparation, storage, handling, and transportation of coal pellets, which can be reslurried into Coal water fuels (CWF) suitable for firing in small- and medium-size commercial and industrial boilers, furnaces, and engines. The project includes preparing coal pellets and capsules from wet filter cake that can be economically stored, handled, transported, and reslurried into a CWF that can be suitably atomized and fired at the user site. The wet cakes studied were prepared from ultra-fine (95% -325 mesh) coal beneficiated by advanced froth-flotation techniques. The coals studied included two eastern bituminous coals, one from Virginia (Elkhorn) and one from Illinois (Illinois No. 6) and one western bituminous coal from Utah (Sky Line coal).

  14. Investigation of open-gradient magnetic separation for Illinois coal

    SciTech Connect

    Doctor, R.D.; Livengood, C.D.; Genens, L.E.; Swietlik, C.E.; Foote, K.

    1987-01-01

    Open-gradient magnetic separation (OGMS) using superconducting quadrupole magnets is a novel coal-beneficiation technology offering high pyritic-sulfur removal from pulverized dry coal. The system operates in a continuous mode, uses no chemicals, and has an estimated power demand 75% lower than techniques using conventional electromagnets, while achieving magnetic separation forces up to 267% higher. Specifically applicable to finely ground coal (120 to 325 mesh), OGMS could encourage the commercialization of other developing coal technologies, such as coal-water slurries, fludized-bed combustion, and coal synfuels. Both the experimental program conducted by Argonne National Laboratory and the results of modeling in support of the experimental program are described. 11 refs., 9 figs.

  15. Characterization and evaluation of washability of Alaskan coals: Fifty selected seams from various coal fields: Final technical report, September 30, 1976-February 28, 1986. [50 coal seams

    SciTech Connect

    Rao, P.D.

    1986-09-01

    This final report is the result of a study initiated in 1976 to obtain washability data for Alaskan coals, to supplement the efforts of the US Department of Energy in their ongoing studies on washability of US coals. Washability characteristics were determined for fifty coal samples from the Northern Alaska, Chicago Creek, Unalakleet, Nenana, Matanuska, Beluga, Yentna and Herendeen Bay coal fields. The raw coal was crushed to 1-1/2 inches, 3/8 inch, 14 mesh and 65 mesh top sizes, and float-sink separations were made at 1.30, 1.40 and 1.60 specific gravities. A limited number of samples were also crushed to 200 and 325 mesh sizes prior to float-sink testing. Samples crushed to 65 mesh top size were also separated at 1.60 specific gravity and the float and sink products were characterized for proximate and ultimate analyses, ash composition and ash fusibility. 72 refs., 79 figs., 57 tabs.

  16. Production of Illinois base compliance coal using enhanced gravity separation. Technical report, March 1, 1994--May 31, 1994

    SciTech Connect

    Paul, B.C.; Honaker, R.Q.

    1994-09-01

    It is well known that froth flotation is inefficient for treating fine coal fractions containing a significant portion of middling particles. On the other hand, gravity-based processes can effectively remove middling particles containing only a small amount of coal. Falcon Concentrators Inc. and Knelson Gold Concentrators Inc. have developed full-scale, enhanced gravity separators for the treatment of heavy minerals. This project is evaluating the potential of using these concentrators to treat Illinois Basin coal fines. During this reporting period, -28 mesh run-of-mine Illinois No. 5 and No. 6 coal samples were processed using a continuous Falcon concentrator having a 10-inch bowl diameter. For the Illinois No. 5 coal sample, the ash content was reduced in the 100 {times} 325 mesh size fraction from about 18% to 8% while achieving a high combustible recovery value of nearly 97%. In addition, the total sulfur content was substantially decreased from 2.6% to 1.7%. Similar results were obtained from the treatment of the Illinois No. 6 coal sample where ash rejections ranged from 40%-70% for a 28 {times} 325 mesh feed having 7% ash. Combustible recovery values from these tests were greater than 87% while treating mass feed rates between 1 to 2 tons/hour. A parametric study found that lower feed solids contents provided marginally lower product ash and total sulfur contents while feed rate and bowl speed appeared to have no significant effect over the range of values tested.

  17. Pelletizing/reslurrying as a means of distributing and firing clean coal. Final quarterly technical progress report No. 6, October 1, 1991--December 31, 1991

    SciTech Connect

    Conkle, H.N.

    1992-03-17

    The objective of this study is to develop technology that permits the practical and economic preparation, storage, handling, and transportation of coal pellets, which can be reslurried into Coal water fuels (CWF) suitable for firing in small- and medium-size commercial and industrial boilers, furnaces, and engines. The project includes preparing coal pellets and capsules from wet filter cake that can be economically stored, handled, transported, and reslurried into a CWF that can be suitably atomized and fired at the user site. The wet cakes studied were prepared from ultra-fine (95% -325 mesh) coal beneficiated by advanced froth-flotation techniques. The coals studied included two eastern bituminous coals, one from Virginia (Elkhorn) and one from Illinois (Illinois No. 6) and one western bituminous coal from Utah (Sky Line coal).

  18. 76 FR 6629 - Agency Information Collection Activities: Forms G-325, G-325A, G-325B, and G-325C; Extension of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-02-07

    ... SECURITY U.S. Citizenship and Immigration Services Agency Information Collection Activities: Forms G-325, G-325A, G- 325B, and G-325C; Extension of an Existing Information Collection; Comment Request ACTION: 60-Day Notice of Information Collection Under Review; Forms 325, G-325A, G-325B, and G-325C,...

  19. Recovery of ultra fine bituminous coal from screen-bowl centrifuge effluent: A possible feedstock for coal-water slurry fuels?

    SciTech Connect

    Morrison, J.L.; Miller, B.G.; Battista, J.J.

    1998-07-01

    Coal fines have historically been viewed as a size fraction which are difficult to handle and expensive to clean and dewater. Consequently, many coal suppliers in the past have chosen to discard their coal fines in slurry impoundments rather than beneficiating them. These disposal costs are then passed onto the end user. Today, with the advent of advanced fine coal cleaning technologies, more stringent environmental policies, and increased pressure by coal-fired utilities to reduce their operating costs, the industry is taking a more progressive look at fine coal recovery options. This paper discusses a fine coal recovery project which is currently being conducted at the Homer City Coal Cleaning Plant (HCCCP) located in western Pennsylvania. The HCCCP utilizes heavy media cyclone, spiral, and conventional froth flotation circuits to clean approximately 4.3 million tons of low to medium volatile bituminous coal annually for the adjacent 1,884 net MW{sub e} Homer City Generating Station. The project focuses on recovering minus 325 mesh coal fines from the effluent of screen-bowl centrifuges. The HCCCP screen-bowl effluent contains approximately 3 to 5 wt.% of suspended coal fines. Approximately 100,000 tons of coal fines are estimated to be lost per year. These coal fines represent a Btu loss, require flocculant prior to the static thickeners and belt presses, contribute excess moisture to the plant refuse which leads to handling and compaction problems during refuse disposal, and contribute to the premature filling of the refuse site.

  20. Recovery of ultra fine bituminous coal from screen-bowl centrifuge effluent: A possible feedstock for coal-water slurry fuels?

    SciTech Connect

    Morrison, J.L.; Miller, B.G.; Battista, J.J.

    1998-04-01

    Coal fines have historically been viewed as a size fraction which are difficult to handle and expensive to clean and dewater. Consequently, many coal suppliers in the past have chosen to discard their coal fines in slurry impoundments rather than beneficiating them. These disposal costs are then passed onto the end user. Today, with the advent of advanced fine coal cleaning technologies, more stringent environmental policies, and increased pressure by coal-fired utilities to reduce their operating costs, the industry is taking a more progressive look at fine coal recovery options. This paper discusses a fine coal recovery project which is currently being conducted at the Homer City Coal Cleaning Plant (HCCCP) located in western Pennsylvania. The HCCCP utilizes heavy media cyclone, spiral, and conventional froth flotation circuits to clean approximately 4.3 million tons of low to medium volatile bituminous coal annually for the adjacent 1,884 net MW{sub e} Homer City Generating Station. The project focuses on recovering minus 325 mesh coal fines from the effluent of screen-bowl centrifuges. The HCCCP screen-bowl effluent contains approximately 3 to 5 wt.% of suspended coal fines. Approximately 100,000 tons of coal fines are estimated to be lost per year. These coal fines represent a Btu loss, require flocculent prior to the static thickeners and belt presses, contribute excess moisture to the plant refuse which leads to handling and compaction problems during refuse disposal, and contribute to the premature filling of the refuse site.

  1. Pneumo MSG-325 Lathe

    SciTech Connect

    Rhorer, R.L.

    1980-01-01

    The LASL Shop Department has recently installed a Pneumo MSG-325 two-axis contouring lathe. This one-microinch resolution lathe, which utilizes both air-bearing spindle and air bearing slide ways, was purchased primarily for miniature work, but can also single point diamond turn metal optics.

  2. Coal.

    ERIC Educational Resources Information Center

    Brant, Russell A.; Glass, Gary B.

    1983-01-01

    Principle work of 23 state geological surveys is summarized. Work includes mapping/estimating coal resources, centralizing data in National Coal Resources Data System through cooperative programs, exploration drilling, and others. Comments on U.S. Geological Survey activities, coal-related conferences/meetings, and industry research activities are…

  3. Surgical Mesh

    MedlinePlus

    ... Device Safety Safety Communications Surgical Mesh: FDA Safety Communication Share Tweet Linkedin Pin it More sharing options ... Prolapse and Stress Urinary Incontinence More in Safety Communications Information About Heparin Preventing Tubing and Luer Misconnections ...

  4. Examination of water spray airborne coal dust capture with three wetting agents

    PubMed Central

    Organiscak, J.A.

    2015-01-01

    Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sink times were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1% and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying and dumping of coal products by comparison to airborne dust capture from sprays. PMID:26251565

  5. Removal of pyrite and trace elements from waste coal by dissolved-CO{sub 2} flotation and chelating agents. Final technical report, September 1, 1993--August 31, 1994

    SciTech Connect

    Shiao, S.Y.; Ho, K.

    1994-12-31

    The overall objective of this project was to use ultrafine bubbles generated by dissolved C0{sub 2} to recover useable fuel, and reject pyrite and other minerals from a waste coal in flotation. In addition, a chelating agent was used to remove trace metals from the froth products. Illinois No. 6 waste coal obtained from a refuse thickener of a coal cleaning circuit was used as the feed in flotation. The as-received waste coal had a top size of 2400 microns. The waste coal was ground to {minus}75 microns ({minus}200 mesh) and {minus}44 microns ({minus}325 mesh). The as-received and the ground waste coal samples were subjected to flotation. Dissolved-CO{sub 2} flotation tests were performed mainly in a 3-inch diameter by 8 feet high packed column under various test conditions. Some tests were also performed in a 2-inch diameter microbubble column for comparison. The flotation performance of the waste coal in the microbubble column was higher than that for the packed column. The packing in the packed column hindered the coal flotation. The separation efficiency of the ground coal was less than that for the asreceived coal. Flotation of the waste coal was also performed in the packed column using coarser bubbles generated by dispersed C0{sub 2} and air. The separation efficiency of the ground waste coal of 44 microns top size was higher than that for dissolved-CO{sub 2} flotation. Additives were used to modify the waste coal surfaces. Triton-X 100, a nonionic surfactant and EDTA, a chelating agent, increased the separation efficiency of the waste coal.Most of the trace metals in coal were reduced in different degrees by flotation. Triton X-100 or EDTA enhanced removal of chromium, nickel, and selenium. Applying EDTA to the froth products further removed lead significantly.

  6. 76 FR 24910 - Agency Information Collection Activities: Forms G-325, G-325A, G-325B, and G-325C; Extension of a...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-03

    ... FR 6629, allowing for a 60-day public comment period. USCIS did not receive any comments for this... SECURITY U.S. Citizenship and Immigration Services Agency Information Collection Activities: Forms G-325, G-325A, G- 325B, and G-325C; Extension of a Currently Approved Information Collection; Comment...

  7. Examination of micrinite concentrates from the Cannel City coal bed of eastern Kentucky: proposed mechanism of formation

    USGS Publications Warehouse

    Taulbee, D.N.; Hower, J.C.; Greb, S.F.

    1991-01-01

    A high volatile B, micrinite-rich bituminous coal from Morgan County, Kentucky, was crushed and screened to -100 mesh, demineralized and subjected to density gradient centrifugation (DGC). In an initial density separation, micrinite concentration was increased from 52 vol% in the demineralized coal to a maximum of 67% in the 1.25-1.26 g/ml density fraction. Micrinite enriched fractions (1.21-1.29 g/ml) were combined to yield a sample containing ???61% micrinite. This sample was crushed to -200 mesh in an attempt to enhance micrinite liberation then reprocessed by DGC. Reprocessing resulted in a slight increase in purity to 69 vol% in the 1.25-1.28 g/ml density fraction. The original -100 mesh sample was density separated a second time with the material recovered between 1.22 and 1.30 g/ml combined, crushed, screened past 325 mesh and reprocessed by DGC. Micrinite was recovered at a purity ranging up to 73% (1.27-1.28 g/ml) from the -325 mesh sample. A density of 1.26g/ml and H/C atomic ratio of 0.79 was calculated for micrinite in one of the higher purity micrinite fractions. These values are notably different than published fusinite values and are more similar to vitrinite values measured in high volatile-B coals. The results from this study suggest that the partitioning of micrinite to a density near that of vitrinite was governed by the inherent micrinite density and not particle aggregation. Transition of the micrinite precursors through a mobile liquid phase is proposed as an explanation for the discrepancy between chemical properties and reflectance as well as to account for the observed microlithological occurrences of micrinite in this sample. ?? 1991.

  8. MeshKit

    2010-10-05

    MeshKit is an open-source library of mesh generation functionality. MeshKit has general mesh manipulation and generation functions such as Copoy, Move, Rotate and Extrude mesh. In addition, new quad mesh and embedded boundary Cartesian mesh algorithm (EB Mesh) are included. Interfaces to several public domain meshing algorithms (TetGen, netgen, triangle, Gmsh, camal) are also offered. This library interacts with mesh data mostly through iMesh including accessing the mesh in parallel. It also can interact withmore » iGeom interface to provide geometry functionality such as importing solid model based geometries. iGeom and IMesh are implemented in the CGM and MOAB packages, respectively. For some non-existing function in iMesh such as tree-construction and ray-tracing, MeshKit also interacts with MOAB functions directly.« less

  9. MeshKit

    SciTech Connect

    2010-10-05

    MeshKit is an open-source library of mesh generation functionality. MeshKit has general mesh manipulation and generation functions such as Copoy, Move, Rotate and Extrude mesh. In addition, new quad mesh and embedded boundary Cartesian mesh algorithm (EB Mesh) are included. Interfaces to several public domain meshing algorithms (TetGen, netgen, triangle, Gmsh, camal) are also offered. This library interacts with mesh data mostly through iMesh including accessing the mesh in parallel. It also can interact with iGeom interface to provide geometry functionality such as importing solid model based geometries. iGeom and IMesh are implemented in the CGM and MOAB packages, respectively. For some non-existing function in iMesh such as tree-construction and ray-tracing, MeshKit also interacts with MOAB functions directly.

  10. Spherical geodesic mesh generation

    SciTech Connect

    Fung, Jimmy; Kenamond, Mark Andrew; Burton, Donald E.; Shashkov, Mikhail Jurievich

    2015-02-27

    In ALE simulations with moving meshes, mesh topology has a direct influence on feature representation and code robustness. In three-dimensional simulations, modeling spherical volumes and features is particularly challenging for a hydrodynamics code. Calculations on traditional spherical meshes (such as spin meshes) often lead to errors and symmetry breaking. Although the underlying differencing scheme may be modified to rectify this, the differencing scheme may not be accessible. This work documents the use of spherical geodesic meshes to mitigate solution-mesh coupling. These meshes are generated notionally by connecting geodesic surface meshes to produce triangular-prismatic volume meshes. This mesh topology is fundamentally different from traditional mesh topologies and displays superior qualities such as topological symmetry. This work describes the geodesic mesh topology as well as motivating demonstrations with the FLAG hydrocode.

  11. 49 CFR 214.325 - Train coordination.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Train coordination. 214.325 Section 214.325 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD WORKPLACE SAFETY Roadway Worker Protection § 214.325 Train coordination. Working limits established by a...

  12. 15 CFR 325.14 - Submitting reports.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Submitting reports. 325.14 Section 325... OF REVIEW § 325.14 Submitting reports. (a) Not later than each anniversary of a certificate's... certificate holder shall submit its annual report to the Secretary. The Secretary shall deliver a copy of...

  13. 14 CFR 325.6 - Periodic reviews.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Periodic reviews. 325.6 Section 325.6... REGULATIONS ESSENTIAL AIR SERVICE PROCEDURES § 325.6 Periodic reviews. (a) The Department will start a periodic review of essential air service within 1 year of the date of the previous determination...

  14. 49 CFR 192.325 - Underground clearance.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Underground clearance. 192.325 Section 192.325... Lines and Mains § 192.325 Underground clearance. (a) Each transmission line must be installed with at least 12 inches (305 millimeters) of clearance from any other underground structure not associated...

  15. 12 CFR 325.2 - Definitions.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Definitions. 325.2 Section 325.2 Banks and Banking FEDERAL DEPOSIT INSURANCE CORPORATION REGULATIONS AND STATEMENTS OF GENERAL POLICY CAPITAL MAINTENANCE Minimum Capital Requirements § 325.2 Definitions. (a) Allowance for loan and lease losses...

  16. 31 CFR 537.325 - Rubies.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 31 Money and Finance:Treasury 3 2014-07-01 2014-07-01 false Rubies. 537.325 Section 537.325 Money... CONTROL, DEPARTMENT OF THE TREASURY BURMESE SANCTIONS REGULATIONS General Definitions § 537.325 Rubies. The term rubies means any rubies classifiable under heading 7103 of the Harmonized Tariff Schedule...

  17. 40 CFR 81.325 - Mississippi.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 17 2011-07-01 2011-07-01 false Mississippi. 81.325 Section 81.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) DESIGNATION OF AREAS FOR AIR QUALITY PLANNING PURPOSES Section 107 Attainment Status Designations § 81.325 Mississippi. Mississippi—TSP Designated area...

  18. 40 CFR 421.325 - [Reserved

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 30 2012-07-01 2012-07-01 false 421.325 Section 421.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Uranium Subcategory § 421.325...

  19. 40 CFR 421.325 - [Reserved

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 29 2014-07-01 2012-07-01 true 421.325 Section 421.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Uranium Subcategory § 421.325...

  20. 40 CFR 421.325 - [Reserved

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 29 2011-07-01 2009-07-01 true 421.325 Section 421.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Uranium Subcategory § 421.325...

  1. 40 CFR 421.325 - [Reserved

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 30 2013-07-01 2012-07-01 true 421.325 Section 421.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Uranium Subcategory § 421.325...

  2. 40 CFR 421.325 - [Reserved

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 28 2010-07-01 2010-07-01 true 421.325 Section 421.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Uranium Subcategory § 421.325...

  3. 9 CFR 325.9 - [Reserved

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false 325.9 Section 325.9 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE AGENCY ORGANIZATION AND TERMINOLOGY... § 325.9...

  4. 29 CFR 32.5 - Assurances required.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 1 2010-07-01 2010-07-01 true Assurances required. 32.5 Section 32.5 Labor Office of the... FINANCIAL ASSISTANCE General Provisions § 32.5 Assurances required. (a) Assurances. An applicant for Federal financial assistance to which this part applies shall submit an assurance, on a form specified by...

  5. 47 CFR 22.325 - Control points.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 2 2013-10-01 2013-10-01 false Control points. 22.325 Section 22.325... Operational and Technical Requirements Operational Requirements § 22.325 Control points. Each station in the Public Mobile Services must have at least one control point and a person on duty who is responsible...

  6. 47 CFR 22.325 - Control points.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 2 2014-10-01 2014-10-01 false Control points. 22.325 Section 22.325... Operational and Technical Requirements Operational Requirements § 22.325 Control points. Each station in the Public Mobile Services must have at least one control point and a person on duty who is responsible...

  7. 47 CFR 22.325 - Control points.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 2 2012-10-01 2012-10-01 false Control points. 22.325 Section 22.325... Operational and Technical Requirements Operational Requirements § 22.325 Control points. Each station in the Public Mobile Services must have at least one control point and a person on duty who is responsible...

  8. 43 CFR 32.5 - Administrative requirements.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 43 Public Lands: Interior 1 2012-10-01 2011-10-01 true Administrative requirements. 32.5 Section 32.5 Public Lands: Interior Office of the Secretary of the Interior GRANTS TO STATES FOR ESTABLISHING YOUNG ADULT CONSERVATION CORPS (YACC) PROGRAM § 32.5 Administrative requirements. (a) The Governor...

  9. 43 CFR 32.5 - Administrative requirements.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 43 Public Lands: Interior 1 2013-10-01 2013-10-01 false Administrative requirements. 32.5 Section 32.5 Public Lands: Interior Office of the Secretary of the Interior GRANTS TO STATES FOR ESTABLISHING YOUNG ADULT CONSERVATION CORPS (YACC) PROGRAM § 32.5 Administrative requirements. (a) The Governor...

  10. 43 CFR 32.5 - Administrative requirements.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 43 Public Lands: Interior 1 2014-10-01 2014-10-01 false Administrative requirements. 32.5 Section 32.5 Public Lands: Interior Office of the Secretary of the Interior GRANTS TO STATES FOR ESTABLISHING YOUNG ADULT CONSERVATION CORPS (YACC) PROGRAM § 32.5 Administrative requirements. (a) The Governor...

  11. 43 CFR 32.5 - Administrative requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Administrative requirements. 32.5 Section 32.5 Public Lands: Interior Office of the Secretary of the Interior GRANTS TO STATES FOR ESTABLISHING YOUNG ADULT CONSERVATION CORPS (YACC) PROGRAM § 32.5 Administrative requirements. (a) The Governor...

  12. 43 CFR 32.5 - Administrative requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 43 Public Lands: Interior 1 2011-10-01 2011-10-01 false Administrative requirements. 32.5 Section 32.5 Public Lands: Interior Office of the Secretary of the Interior GRANTS TO STATES FOR ESTABLISHING YOUNG ADULT CONSERVATION CORPS (YACC) PROGRAM § 32.5 Administrative requirements. (a) The Governor...

  13. 45 CFR 32.5 - Hearing.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 45 Public Welfare 1 2011-10-01 2011-10-01 false Hearing. 32.5 Section 32.5 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION ADMINISTRATIVE WAGE GARNISHMENT § 32.5 Hearing... official's findings, analysis, and conclusions; and (3) The terms of any repayment schedule, if...

  14. 45 CFR 32.5 - Hearing.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 45 Public Welfare 1 2010-10-01 2010-10-01 false Hearing. 32.5 Section 32.5 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION ADMINISTRATIVE WAGE GARNISHMENT § 32.5 Hearing... official's findings, analysis, and conclusions; and (3) The terms of any repayment schedule, if...

  15. 20 CFR 325.1 - General.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 20 Employees' Benefits 1 2011-04-01 2011-04-01 false General. 325.1 Section 325.1 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.1 General. (a) Day of unemployment. A “day of unemployment” is a calendar day on which an employee,...

  16. 49 CFR 325.93 - Tires.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Systems and Tires § 325.93 Tires. (a) Except as provided in paragraph (b) of this section, a motor vehicle does not conform to the visual tire inspection requirements, 40 CFR 202.23, of the Interstate Motor... 49 Transportation 5 2012-10-01 2012-10-01 false Tires. 325.93 Section 325.93 Transportation...

  17. 49 CFR 325.93 - Tires.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Systems and Tires § 325.93 Tires. (a) Except as provided in paragraph (b) of this section, a motor vehicle does not conform to the visual tire inspection requirements, 40 CFR 202.23, of the Interstate Motor... 49 Transportation 5 2013-10-01 2013-10-01 false Tires. 325.93 Section 325.93 Transportation...

  18. 49 CFR 325.93 - Tires.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Systems and Tires § 325.93 Tires. (a) Except as provided in paragraph (b) of this section, a motor vehicle does not conform to the visual tire inspection requirements, 40 CFR 202.23, of the Interstate Motor... 49 Transportation 5 2014-10-01 2014-10-01 false Tires. 325.93 Section 325.93 Transportation...

  19. 49 CFR 325.93 - Tires.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Systems and Tires § 325.93 Tires. (a) Except as provided in paragraph (b) of this section, a motor vehicle does not conform to the visual tire inspection requirements, 40 CFR 202.23, of the Interstate Motor... 49 Transportation 5 2010-10-01 2010-10-01 false Tires. 325.93 Section 325.93 Transportation...

  20. 49 CFR 325.93 - Tires.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Systems and Tires § 325.93 Tires. (a) Except as provided in paragraph (b) of this section, a motor vehicle does not conform to the visual tire inspection requirements, 40 CFR 202.23, of the Interstate Motor... 49 Transportation 5 2011-10-01 2011-10-01 false Tires. 325.93 Section 325.93 Transportation...

  1. 47 CFR 22.325 - Control points.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Control points. 22.325 Section 22.325... Operational and Technical Requirements Operational Requirements § 22.325 Control points. Each station in the Public Mobile Services must have at least one control point and a person on duty who is responsible...

  2. 47 CFR 22.325 - Control points.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 2 2011-10-01 2011-10-01 false Control points. 22.325 Section 22.325... Operational and Technical Requirements Operational Requirements § 22.325 Control points. Each station in the Public Mobile Services must have at least one control point and a person on duty who is responsible...

  3. 12 CFR 325.5 - Miscellaneous.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 4 2011-01-01 2011-01-01 false Miscellaneous. 325.5 Section 325.5 Banks and Banking FEDERAL DEPOSIT INSURANCE CORPORATION REGULATIONS AND STATEMENTS OF GENERAL POLICY CAPITAL MAINTENANCE Minimum Capital Requirements § 325.5 Miscellaneous. (a) Intangible assets. Any intangible assets that were explicitly approved by the FDIC...

  4. 8 CFR 325.3 - Residence.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 8 Aliens and Nationality 1 2011-01-01 2011-01-01 false Residence. 325.3 Section 325.3 Aliens and Nationality DEPARTMENT OF HOMELAND SECURITY NATIONALITY REGULATIONS NATIONALS BUT NOT CITIZENS OF THE UNITED STATES; RESIDENCE WITHIN OUTLYING POSSESSIONS § 325.3 Residence. (a) For purposes of applying...

  5. 8 CFR 325.2 - Eligibility.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 8 Aliens and Nationality 1 2011-01-01 2011-01-01 false Eligibility. 325.2 Section 325.2 Aliens and Nationality DEPARTMENT OF HOMELAND SECURITY NATIONALITY REGULATIONS NATIONALS BUT NOT CITIZENS OF THE UNITED STATES; RESIDENCE WITHIN OUTLYING POSSESSIONS § 325.2 Eligibility. An applicant for naturalization...

  6. 8 CFR 325.3 - Residence.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 8 Aliens and Nationality 1 2010-01-01 2010-01-01 false Residence. 325.3 Section 325.3 Aliens and Nationality DEPARTMENT OF HOMELAND SECURITY NATIONALITY REGULATIONS NATIONALS BUT NOT CITIZENS OF THE UNITED STATES; RESIDENCE WITHIN OUTLYING POSSESSIONS § 325.3 Residence. (a) For purposes of applying...

  7. 8 CFR 325.1 - [Reserved

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 8 Aliens and Nationality 1 2010-01-01 2010-01-01 false 325.1 Section 325.1 Aliens and Nationality DEPARTMENT OF HOMELAND SECURITY NATIONALITY REGULATIONS NATIONALS BUT NOT CITIZENS OF THE UNITED STATES; RESIDENCE WITHIN OUTLYING POSSESSIONS § 325.1...

  8. 8 CFR 325.4 - Application; documents.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 8 Aliens and Nationality 1 2010-01-01 2010-01-01 false Application; documents. 325.4 Section 325.4 Aliens and Nationality DEPARTMENT OF HOMELAND SECURITY NATIONALITY REGULATIONS NATIONALS BUT NOT CITIZENS OF THE UNITED STATES; RESIDENCE WITHIN OUTLYING POSSESSIONS § 325.4 Application; documents. (a)...

  9. 8 CFR 325.1 - [Reserved

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 8 Aliens and Nationality 1 2011-01-01 2011-01-01 false 325.1 Section 325.1 Aliens and Nationality DEPARTMENT OF HOMELAND SECURITY NATIONALITY REGULATIONS NATIONALS BUT NOT CITIZENS OF THE UNITED STATES; RESIDENCE WITHIN OUTLYING POSSESSIONS § 325.1...

  10. 8 CFR 325.2 - Eligibility.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 8 Aliens and Nationality 1 2010-01-01 2010-01-01 false Eligibility. 325.2 Section 325.2 Aliens and Nationality DEPARTMENT OF HOMELAND SECURITY NATIONALITY REGULATIONS NATIONALS BUT NOT CITIZENS OF THE UNITED STATES; RESIDENCE WITHIN OUTLYING POSSESSIONS § 325.2 Eligibility. An applicant for naturalization...

  11. 8 CFR 325.4 - Application; documents.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 8 Aliens and Nationality 1 2011-01-01 2011-01-01 false Application; documents. 325.4 Section 325.4 Aliens and Nationality DEPARTMENT OF HOMELAND SECURITY NATIONALITY REGULATIONS NATIONALS BUT NOT CITIZENS OF THE UNITED STATES; RESIDENCE WITHIN OUTLYING POSSESSIONS § 325.4 Application; documents. (a)...

  12. 15 CFR 325.11 - Judicial review.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Judicial review. 325.11 Section 325.11... REVIEW § 325.11 Judicial review. (a) Review of certain determinations. (1) Any person aggrieved by a... judicial review, determinations of the Secretary are final when notice is published in the Federal...

  13. 7 CFR 4274.325 - Interest rates.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Interest rates. 4274.325 Section 4274.325 Agriculture... (IRP) § 4274.325 Interest rates. (a) Loans made by the Agency pursuant to this subpart shall bear interest at a fixed rate of 1 percent per annum over the term of the loan. (b) Interest rates charged...

  14. 28 CFR 32.5 - Evidence.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 28 Judicial Administration 1 2011-07-01 2011-07-01 false Evidence. 32.5 Section 32.5 Judicial Administration DEPARTMENT OF JUSTICE PUBLIC SAFETY OFFICERS' DEATH, DISABILITY, AND EDUCATIONAL ASSISTANCE BENEFIT CLAIMS General Provisions § 32.5 Evidence. (a) Except as otherwise may be expressly provided in the Act or this part, a claimant has...

  15. 14 CFR 325.2 - Applicability.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false Applicability. 325.2 Section 325.2 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION PROCEEDINGS) PROCEDURAL REGULATIONS ESSENTIAL AIR SERVICE PROCEDURES § 325.2 Applicability. This part applies to essential air...

  16. 14 CFR 325.2 - Applicability.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Applicability. 325.2 Section 325.2 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION PROCEEDINGS) PROCEDURAL REGULATIONS ESSENTIAL AIR SERVICE PROCEDURES § 325.2 Applicability. This part applies to essential air...

  17. Mesh Quality Improvement Toolkit

    2002-11-15

    MESQUITE is a linkable software library to be used by simulation and mesh generation tools to improve the quality of meshes. Mesh quality is improved by node movement and/or local topological modifications. Various aspects of mesh quality such as smoothness, element shape, size, and orientation are controlled by choosing the appropriate mesh qualtiy metric, and objective function tempate, and a numerical optimization solver to optimize the quality of meshes, MESQUITE uses the TSTT mesh interfacemore » specification to provide an interoperable toolkit that can be used by applications which adopt the standard. A flexible code design makes it easy for meshing researchers to add additional mesh quality metrics, templates, and solvers to develop new quality improvement algorithms by making use of the MESQUITE infrastructure.« less

  18. Hexahedral Mesh Untangling

    SciTech Connect

    KNUPP,PATRICK

    2000-12-13

    We investigate a well-motivated mesh untangling objective function whose optimization automatically produces non-inverted elements when possible. Examples show the procedure is highly effective on simplicial meshes and on non-simplicial (e.g., hexahedral) meshes constructed via mapping or sweeping algorithms. The current whisker-weaving (WW) algorithm in CUBIT usually produces hexahedral meshes that are unsuitable for analyses due to inverted elements. The majority of these meshes cannot be untangled using the new objective function. The most likely source of the difficulty is poor mesh topology.

  19. 12 CFR 32.5 - Combination rules.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 1 2013-01-01 2013-01-01 false Combination rules. 32.5 Section 32.5 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY LENDING LIMITS § 32.5 Combination rules. (a) General rule. Loans or extensions of credit to one borrower will be attributed to another person and each person will be deemed a borrower—...

  20. 12 CFR 32.5 - Combination rules.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 1 2012-01-01 2012-01-01 false Combination rules. 32.5 Section 32.5 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY LENDING LIMITS § 32.5 Combination rules. (a) General rule. Loans or extensions of credit to one borrower will be attributed to another person and each person will be deemed a borrower—...

  1. 7 CFR 1207.325 - Procedure.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan National Potato Promotion Board § 1207.325 Procedure. (a) Each...

  2. 7 CFR 1207.325 - Procedure.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan National Potato Promotion Board § 1207.325 Procedure. (a) Each...

  3. 7 CFR 1207.325 - Procedure.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan National Potato Promotion Board § 1207.325 Procedure. (a) Each...

  4. 7 CFR 1207.325 - Procedure.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan National Potato Promotion Board § 1207.325 Procedure. (a) Each...

  5. 7 CFR 1207.325 - Procedure.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan National Potato Promotion Board § 1207.325 Procedure. (a) Each...

  6. 7 CFR 1205.325 - Selection.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE COTTON RESEARCH AND PROMOTION Cotton Research and Promotion Order Cotton Board § 1205.325 Selection. From the nominations made pursuant...

  7. 7 CFR 1205.325 - Selection.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE COTTON RESEARCH AND PROMOTION Cotton Research and Promotion Order Cotton Board § 1205.325 Selection. From the nominations made pursuant...

  8. 7 CFR 1205.325 - Selection.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE COTTON RESEARCH AND PROMOTION Cotton Research and Promotion Order Cotton Board § 1205.325 Selection. From the nominations made pursuant...

  9. 7 CFR 1205.325 - Selection.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE COTTON RESEARCH AND PROMOTION Cotton Research and Promotion Order Cotton Board § 1205.325 Selection. From the nominations made pursuant...

  10. 7 CFR 1205.325 - Selection.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE COTTON RESEARCH AND PROMOTION Cotton Research and Promotion Order Cotton Board § 1205.325 Selection. From the nominations made pursuant...

  11. Mesh Excision: Is Total Mesh Excision Necessary?

    PubMed

    Wolff, Gillian F; Winters, J Christian; Krlin, Ryan M

    2016-04-01

    Nearly 29% of women will undergo a secondary, repeat operation for pelvic organ prolapse (POP) symptom recurrence following a primary repair, as reported by Abbott et al. (Am J Obstet Gynecol 210:163.e1-163.e1, 2014). In efforts to decrease the rates of failure, graft materials have been utilized to augment transvaginal repairs. Following the success of using polypropylene mesh (PPM) for stress urinary incontinence (SUI), the use of PPM in the transvaginal repair of POP increased. However, in recent years, significant concerns have been raised about the safety of PPM mesh. Complications, some specific to mesh, such as exposures, erosion, dyspareunia, and pelvic pain, have been reported with increased frequency. In the current literature, there is not substantive evidence to suggest that PPM has intrinsic properties that warrant total mesh removal in the absence of complications. There are a number of complications that can occur after transvaginal mesh placement that do warrant surgical intervention after failure of conservative therapy. In aggregate, there are no high-quality controlled studies that clearly demonstrate that total mesh removal is consistently more likely to achieve pain reduction. In the cases of obstruction and erosion, it seems clear that definitive removal of the offending mesh is associated with resolution of symptoms in the majority of cases and reasonable practice. There are a number of complications that can occur with removal of mesh, and patients should be informed of this as they formulate a choice of treatment. We will review these considerations as we examine the clinical question of whether total versus partial removal of mesh is necessary for the resolution of complications following transvaginal mesh placement. PMID:26905696

  12. Compact Mesh Generator

    2007-02-02

    The CMG is a small, lightweight, structured mesh generation code. It features a simple text input parser that allows setup of various meshes via a small set of text commands. Mesh generation data can be output to text, the silo file format, or the API can be directly queried by applications. It can run serially or in parallel via MPI. The CMG includes the ability to specify varius initial conditions on a mesh via meshmore » tags.« less

  13. Meshes: The next generation

    SciTech Connect

    Christon, M.; Hardin, D.; Compton, J.; Zosel, M.

    1994-08-29

    Building complex meshes for large-scale numerical simulations presents immense difficulties in exploiting high-performance computers. Industry and research leaders will describe the current state of the art for generating meshes for such large scientific problems. This will be followed by a panel and general audience discussion of the algorithmic and architectural issues surrounding the generation of meshes with10{sup 7} to 10{sup 9} grid points. (Note: The terms ``mesh`` and ``grid`` are used interchangeably in the literature.)

  14. Hydrothermally treated coals for pulverized coal injection. Final technical report

    SciTech Connect

    Walsh, D.E.; Rao, P.D.; Ogunsola, O.; Lin, H.K.

    1995-10-01

    This project investigated the suitability of hydrothermally dried low-rank coals for pulverized fuel injection into blast furnaces in order to reduce coke consumption. Coal samples from the Beluga coalfield and the Usibelli Coal Mine, Alaska, were used for the study. Crushed coal samples were hydrothermally treated at three temperatures, 275, 300 and 325{degrees}C, for residence times of 10, 60 and 120 minutes. Products were characterized to determine their suitability for pulverized coal injection. Characterization included proximate and ultimate analyses, vitrinite reflectance and TGA reactivity. A literature survey was also conducted.

  15. 49 CFR 214.325 - Train coordination.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ..., DEPARTMENT OF TRANSPORTATION RAILROAD WORKPLACE SAFETY Roadway Worker Protection § 214.325 Train coordination. Working limits established by a roadway worker through the use of train coordination shall comply with the... 49 Transportation 4 2014-10-01 2014-10-01 false Train coordination. 214.325 Section...

  16. 49 CFR 214.325 - Train coordination.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ..., DEPARTMENT OF TRANSPORTATION RAILROAD WORKPLACE SAFETY Roadway Worker Protection § 214.325 Train coordination. Working limits established by a roadway worker through the use of train coordination shall comply with the... 49 Transportation 4 2011-10-01 2011-10-01 false Train coordination. 214.325 Section...

  17. 49 CFR 214.325 - Train coordination.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ..., DEPARTMENT OF TRANSPORTATION RAILROAD WORKPLACE SAFETY Roadway Worker Protection § 214.325 Train coordination. Working limits established by a roadway worker through the use of train coordination shall comply with the... 49 Transportation 4 2013-10-01 2013-10-01 false Train coordination. 214.325 Section...

  18. 49 CFR 214.325 - Train coordination.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ..., DEPARTMENT OF TRANSPORTATION RAILROAD WORKPLACE SAFETY Roadway Worker Protection § 214.325 Train coordination. Working limits established by a roadway worker through the use of train coordination shall comply with the... 49 Transportation 4 2012-10-01 2012-10-01 false Train coordination. 214.325 Section...

  19. 10 CFR 205.325 - Annual report.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 3 2010-01-01 2010-01-01 false Annual report. 205.325 Section 205.325 Energy DEPARTMENT OF ENERGY OIL ADMINISTRATIVE PROCEDURES AND SANCTIONS Electric Power System Permits and Reports... Construction, Connection, Operation, and Maintenance of Facilities for Transmission of Electric Energy...

  20. 49 CFR 325.5 - Definitions.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 5 2012-10-01 2012-10-01 false Definitions. 325.5 Section 325.5 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION GENERAL REGULATIONS COMPLIANCE WITH INTERSTATE MOTOR CARRIER NOISE EMISSION STANDARDS General Provisions §...

  1. 49 CFR 325.5 - Definitions.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 5 2014-10-01 2014-10-01 false Definitions. 325.5 Section 325.5 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION GENERAL REGULATIONS COMPLIANCE WITH INTERSTATE MOTOR CARRIER NOISE EMISSION STANDARDS General Provisions §...

  2. 49 CFR 192.325 - Underground clearance.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Underground clearance. 192.325 Section 192.325 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM...

  3. 10 CFR 1023.325 - Further proceedings.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... the Board's Rules of Practice, 10 CFR part 1023, which is made in the covered proceeding for which... 10 Energy 4 2010-01-01 2010-01-01 false Further proceedings. 1023.325 Section 1023.325 Energy DEPARTMENT OF ENERGY (GENERAL PROVISIONS) CONTRACT APPEALS Procedures Relating to Awards Under the...

  4. 14 CFR 93.325 - Quarterly reporting.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 2 2014-01-01 2014-01-01 false Quarterly reporting. 93.325 Section 93.325 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES SPECIAL AIR TRAFFIC RULES Special Flight Rules in the Vicinity of Grand Canyon National Park, AZ §...

  5. 9 CFR 3.25 - Facilities, general.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Facilities, general. 3.25 Section 3.25 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL WELFARE STANDARDS Specifications for the Humane Handling, Care, Treatment, and Transportation of Guinea Pigs and Hamsters Facilities...

  6. 29 CFR 780.325 - Principally engaged.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Agriculture That Is Exempted From the Minimum Wage and Overtime Pay Requirements Under Section 13(a)(6... 29 Labor 3 2014-07-01 2014-07-01 false Principally engaged. 780.325 Section 780.325 Labor Regulations Relating to Labor (Continued) WAGE AND HOUR DIVISION, DEPARTMENT OF LABOR STATEMENTS OF...

  7. 29 CFR 780.325 - Principally engaged.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Agriculture That Is Exempted From the Minimum Wage and Overtime Pay Requirements Under Section 13(a)(6... 29 Labor 3 2012-07-01 2012-07-01 false Principally engaged. 780.325 Section 780.325 Labor Regulations Relating to Labor (Continued) WAGE AND HOUR DIVISION, DEPARTMENT OF LABOR STATEMENTS OF...

  8. 29 CFR 780.325 - Principally engaged.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Agriculture That Is Exempted From the Minimum Wage and Overtime Pay Requirements Under Section 13(a)(6... 29 Labor 3 2010-07-01 2010-07-01 false Principally engaged. 780.325 Section 780.325 Labor Regulations Relating to Labor (Continued) WAGE AND HOUR DIVISION, DEPARTMENT OF LABOR STATEMENTS OF...

  9. 29 CFR 780.325 - Principally engaged.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Agriculture That Is Exempted From the Minimum Wage and Overtime Pay Requirements Under Section 13(a)(6... 29 Labor 3 2011-07-01 2011-07-01 false Principally engaged. 780.325 Section 780.325 Labor Regulations Relating to Labor (Continued) WAGE AND HOUR DIVISION, DEPARTMENT OF LABOR STATEMENTS OF...

  10. 29 CFR 780.325 - Principally engaged.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Agriculture That Is Exempted From the Minimum Wage and Overtime Pay Requirements Under Section 13(a)(6... 29 Labor 3 2013-07-01 2013-07-01 false Principally engaged. 780.325 Section 780.325 Labor Regulations Relating to Labor (Continued) WAGE AND HOUR DIVISION, DEPARTMENT OF LABOR STATEMENTS OF...

  11. 24 CFR 582.325 - Outreach activities.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 3 2011-04-01 2010-04-01 true Outreach activities. 582.325 Section 582.325 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued) OFFICE OF ASSISTANT SECRETARY FOR COMMUNITY PLANNING AND DEVELOPMENT, DEPARTMENT OF HOUSING AND...

  12. 14 CFR 93.325 - Quarterly reporting.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 2 2013-01-01 2013-01-01 false Quarterly reporting. 93.325 Section 93.325 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES SPECIAL AIR TRAFFIC RULES Special Flight Rules in the Vicinity of Grand Canyon National Park, AZ §...

  13. Investigation of the behavior of potentially hazardous trace elements in Kentucky coals and combustion byproducts

    SciTech Connect

    Robertson, J.D.; Blanchard, L.J.; Srikantapura, S.; Parekh, B.K.; Lafferty, C.J.

    1996-12-31

    The minor- and trace-element content of coal is of great interest because of the potentially hazardous impact on human health and the environment resulting from their release during coal combustion. Of the one billion tons of coal mined annually in the United States, 85-90% is consumed by coal-fired power plants. Potentially toxic elements present at concentrations as low as a few egg can be released in large quantities from combustion of this magnitude. Of special concern are those trace elements that occur naturally in coal which have been designated as potential hazardous air pollutants (HAPs) in the 1990 Amendments to the Clean Air Act. The principle objective of this work was to investigate a combination of physical and chemical coal cleaning techniques to remove 90 percent of HAP trace elements at 90 percent combustibles recovery from Kentucky No. 9 coal. Samples of this coal were first subjected to physical separation by flotation in a Denver cell. The float fraction from the Denver cell was then used as feed material for hydrothermal leaching tests in which the efficacy of dilute alkali (NaOH) and acid (HNO{sub 3}) solutions at various temperatures and pressures was investigated. The combined column flotation and mild chemical cleaning strategy removed 60-80% of trace elements with greater than 85, recovery of combustibles from very finely ground (-325 mesh) coal. The elemental composition of the samples generated at each stage was determined using particle induced X-ray emission (PIXE) analysis. PIXE is a rapid, instrumental technique that, in principle, is capable of analyzing all elements from sodium through uranium with sensitivities as low as 1 {mu}g/g.

  14. phdMesh

    2008-01-01

    Parallel Heterogeneous Dynamic unstructured Mesh (phdMesh) data structure library and integration testing code that performs dynamic load balancing of the data structure and parallel geometric proximity search on a contrived test problem. The phdMesh library is intended to be module within a finite element or finite volume library or code. The integration testing code is intended to provide a compact and highly portable performance evaluation code for parallel computing systems.

  15. Gear mesh compliance modeling

    NASA Technical Reports Server (NTRS)

    Savage, M.; Caldwell, R. J.; Wisor, G. D.; Lewicki, D. G.

    1986-01-01

    A computer model has been constructed to simulate the compliance and load sharing in a spur gear mesh. The model adds the effect of rim deflections to previously developed state-of-the-art gear tooth deflection models. The effects of deflections on mesh compliance and load sharing are examined. The model can treat gear meshes composed to two external gears or an external gear driving an internal gear. The model includes deflection contributions from the bending and shear in the teeth, the Hertzian contact deformations, and primary and secondary rotations of the gear rims. The model shows that rimmed gears increase mesh compliance and, in some cases, improve load sharing.

  16. Gear mesh compliance modeling

    NASA Technical Reports Server (NTRS)

    Savage, M.; Caldwell, R. J.; Wisor, G. D.; Lewicki, D. G.

    1987-01-01

    A computer model has been constructed to simulate the compliance and load sharing in a spur gear mesh. The model adds the effect of rim deflections to previously developed state-of-the-art gear tooth deflection models. The effects of deflections on mesh compliance and load sharing are examined. The model can treat gear meshes composed of two external gears or an external gear driving an internal gear. The model includes deflection contributions from the bending and shear in the teeth, the Hertzian contact deformations, and primary and secondary rotations of the gear rims. The model shows that rimmed gears increase mesh compliance and, in some cases, improve load sharing.

  17. Characterization of fly ash from low-sulfur and high-sulfur coal sources: Partitioning of carbon and trace elements with particle size

    USGS Publications Warehouse

    Hower, J.C.; Trimble, A.S.; Eble, C.F.; Palmer, C.A.; Kolker, A.

    1999-01-01

    Fly ash samples were collected in November and December of 1994, from generating units at a Kentucky power station using high- and low-sulfur feed coals. The samples are part of a two-year study of the coal and coal combustion byproducts from the power station. The ashes were wet screened at 100, 200, 325, and 500 mesh (150, 75, 42, and 25 ??m, respectively). The size fractions were then dried, weighed, split for petrographic and chemical analysis, and analyzed for ash yield and carbon content. The low-sulfur "heavy side" and "light side" ashes each have a similar size distribution in the November samples. In contrast, the December fly ashes showed the trend observed in later months, the light-side ash being finer (over 20 % more ash in the -500 mesh [-25 ??m] fraction) than the heavy-side ash. Carbon tended to be concentrated in the coarse fractions in the December samples. The dominance of the -325 mesh (-42 ??m) fractions in the overall size analysis implies, though, that carbon in the fine sizes may be an important consideration in the utilization of the fly ash. Element partitioning follows several patterns. Volatile elements, such as Zn and As, are enriched in the finer sizes, particularly in fly ashes collected at cooler, light-side electrostatic precipitator (ESP) temperatures. The latter trend is a function of precipitation at the cooler-ESP temperatures and of increasing concentration with the increased surface area of the finest fraction. Mercury concentrations are higher in high-carbon fly ashes, suggesting Hg adsorption on the fly ash carbon. Ni and Cr are associated, in part, with the spinel minerals in the fly ash. Copyright ?? 1999 Taylor & Francis.

  18. 9 CFR 3.25 - Facilities, general.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... Pigs and Hamsters Facilities and Operating Standards § 3.25 Facilities, general. (a) Structural strength. Indoor and outdoor housing facilities for guinea pigs or hamsters shall be structurally sound...

  19. 7 CFR 58.325 - Anhydrous milkfat.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58.325 Anhydrous milkfat. If cream is used in the production of anhydrous milkfat that...

  20. 7 CFR 58.325 - Anhydrous milkfat.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Quality Specifications for Raw Material § 58.325 Anhydrous milkfat. If cream is used in the production of anhydrous milkfat that...

  1. 21 CFR 558.325 - Lincomycin.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... citations affecting § 558.325, see the List of CFR Sections Affected, which appears in the Finding Aids...: “CAUTION: Do not allow rabbits, hamsters, guinea pigs, horses, or ruminants access to feeds...

  2. 14 CFR 93.325 - Quarterly reporting.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... AND GENERAL OPERATING RULES SPECIAL AIR TRAFFIC RULES Special Flight Rules in the Vicinity of Grand Canyon National Park, AZ § 93.325 Quarterly reporting. (a) Each certificate holder must submit in...

  3. 14 CFR 93.325 - Quarterly reporting.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... AND GENERAL OPERATING RULES SPECIAL AIR TRAFFIC RULES Special Flight Rules in the Vicinity of Grand Canyon National Park, AZ § 93.325 Quarterly reporting. (a) Each certificate holder must submit in...

  4. 14 CFR 93.325 - Quarterly reporting.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AND GENERAL OPERATING RULES SPECIAL AIR TRAFFIC RULES Special Flight Rules in the Vicinity of Grand Canyon National Park, AZ § 93.325 Quarterly reporting. (a) Each certificate holder must submit in...

  5. Optimization of tetrahedral meshes

    SciTech Connect

    Briere De L`Isle, E.; George, P.L.

    1995-12-31

    Finite element computations are all the more exact if we start from {open_quotes}good{close_quotes} elements. We are interested in meshes where the elements are tetrahedra and we shall develop utilities allowing us to improve the quality of these meshes.

  6. MEDICAL SUBJECTS HEADING (MESH)

    EPA Science Inventory

    MeSH is the National Library of Medicine's controlled vocabulary thesaurus. It consists of sets of terms naming descriptors in a hierarchical structure that permits searching at various levels of specificity. MeSH descriptors are arranged in both an alphabetic and a hierarchical ...

  7. Mercury in coals and fly ashes from Republika and Bobov dol thermoelectric power plants

    USGS Publications Warehouse

    Kostova, I.; Vassileva, C.; Hower, J.; Mastalerz, Maria; Vassilev, S.; Nikolova, N.

    2011-01-01

    Feed coal and y ash samples were collected at Republika and Bobov Dol thermoelectric power plants (TPPs). The y ashes (FAs) were collected fromthree rows of the hot-side electrostatic precipitators (ESPs) array. Each sam- ple was wet-screened at 100, 200, 325 and 500 mesh. The coals and y ashes were characterized with regard to their petrological and chemical composition (including mercury content) and to their surface area properties. The calculated enrichment factor (EF) shows that the Hg concentrations in the bulk coal samples from Republika and Bobov Dol TPPs are 2.19 and 1.41, respectively. In some coal size fractions the EF can be up to 4 times higher than the Clarke value. The calculated EF for fly ashes shows that the Hg concentrations in the bulk samples studied are lower (between 0.03 and 0.32) than the Clarke value. The most enriched in Hg are the fly ashes from the 3rd ESP row of Republika TPP. The Hg distribution in bulk FAs taken from dierent rows of the electrostatic precipitators of both TPPs studied shows well established tendency of gradual increase in the Hg content from the 1st to the 2nd and 3rd ESP rows. The correlation between Hg content and surface area, mesopore and micropore volume of y ashes was also done in the present investigation.

  8. Optimized testing of meshes

    NASA Technical Reports Server (NTRS)

    Malek, Miroslaw; Ozden, Banu

    1990-01-01

    Efficient testing techniques for two-dimensional mesh interconnection networks are presented. The tests cover faults in the arbitration logic of the switches; this includes an examination of fault detection in the data paths, routing, and control circuitry, including the conflict resolution capabilities of mesh interconnection networks using topological test methods. The proposed methods are not implementation specific and can be applied to any design with a mesh topology. The topology and behavior of the network are described and definitions are presented. The fault model is defined and parallel testing methods for the entire network are given.

  9. Natural gas storage with activated carbon from a bituminous coal

    USGS Publications Warehouse

    Sun, Jielun; Rood, M.J.; Rostam-Abadi, M.; Lizzio, A.A.

    1996-01-01

    Granular activated carbons ( -20 + 100 mesh; 0.149-0.84 mm) were produced by physical activation and chemical activation with KOH from an Illinois bituminous coal (IBC-106) for natural gas storage. The products were characterized by BET surface area, micropore volume, bulk density, and methane adsorption capacities. Volumetric methane adsorption capacities (Vm/Vs) of some of the granular carbons produced by physical activation are about 70 cm3/cm3 which is comparable to that of BPL, a commercial activated carbon. Vm/Vs values above 100 cm3/cm3 are obtainable by grinding the granular products to - 325 mesh (<0.044 mm). The increase in Vm/Vs is due to the increase in bulk density of the carbons. Volumetric methane adsorption capacity increases with increasing pore surface area and micropore volume when normalizing with respect to sample bulk volume. Compared with steam-activated carbons, granular carbons produced by KOH activation have higher micropore volume and higher methane adsorption capacities (g/g). Their volumetric methane adsorption capacities are lower due to their lower bulk densities. Copyright ?? 1996 Elsevier Science Ltd.

  10. Mesh implants: An overview of crucial mesh parameters

    PubMed Central

    Zhu, Lei-Ming; Schuster, Philipp; Klinge, Uwe

    2015-01-01

    Hernia repair is one of the most frequently performed surgical interventions that use mesh implants. This article evaluates crucial mesh parameters to facilitate selection of the most appropriate mesh implant, considering raw materials, mesh composition, structure parameters and mechanical parameters. A literature review was performed using the PubMed database. The most important mesh parameters in the selection of a mesh implant are the raw material, structural parameters and mechanical parameters, which should match the physiological conditions. The structural parameters, especially the porosity, are the most important predictors of the biocompatibility performance of synthetic meshes. Meshes with large pores exhibit less inflammatory infiltrate, connective tissue and scar bridging, which allows increased soft tissue ingrowth. The raw material and combination of raw materials of the used mesh, including potential coatings and textile design, strongly impact the inflammatory reaction to the mesh. Synthetic meshes made from innovative polymers combined with surface coating have been demonstrated to exhibit advantageous behavior in specialized fields. Monofilament, large-pore synthetic meshes exhibit advantages. The value of mesh classification based on mesh weight seems to be overestimated. Mechanical properties of meshes, such as anisotropy/isotropy, elasticity and tensile strength, are crucial parameters for predicting mesh performance after implantation. PMID:26523210

  11. Urogynecologic Surgical Mesh Implants

    MedlinePlus

    ... Boston Scientific's urogynecologic surgical mesh may contain counterfeit raw material. We are examining these allegations to determine any ... are currently not aware that the alleged counterfeit raw material contributes to adverse events associated with these products. ...

  12. Hydrothermally treated coals for pulverized coal injection. [Quarterly] technical progress report, January--March 1995

    SciTech Connect

    Walsh, D.E.; Rao, P.D.; Ogunsola, O.; Lin, H.K.

    1995-04-01

    This project is investigating the suitability of hydrothermally dried low-rank coals for pulverized fuel injection into blast furnaces in order to reduce coke consumption. Coal samples from the Beluga coal field and the Usibelli Coal Mine, Alaska, are being used for the study. Crushed coal samples were hydrothermally treated at three temperatures, 275, 300 and 325{degrees}C, for residence times ranging from 10 to 120 minutes. Products are being characterized to determine their suitability for pulverized coal injection. Characterization includes proximate and ultimate analyses, vitrinite reflectance and TGA reactivity. A literature survey is being conducted.

  13. Hydrothermally treated coals for pulverized coal injection. Technical progress report, April 1995--June 1995

    SciTech Connect

    Walsh, D.E.; Rao, P.D.; Ogunsola, O.; Lin, H.K.

    1995-07-01

    This project is investigating the suitability of hydrothermally dried low-rank coals for pulverized fuel injection into blast furnaces in order to reduce coke consumption. Coal samples from the Beluga coal field and Usibelli Coal Mine, Alaska, are being used for the study. Crushed coal samples were hydrothermally treated at three temperatures, 275, 300 and 325{degrees}C, for residence times ranging from 10 to 120 minutes. Products have been characterized to determine their suitability for pulverized coal injection. Characterization includes proximate and ultimate analyses, vitrinite reflectance, TGA reactivity and thermochemical modeling. A literature survey has been conducted.

  14. Filtering coal-derived oil through a filter media precoated with particles partially solubilized by said oil

    DOEpatents

    Rodgers, Billy R.; Edwards, Michael S.

    1977-01-01

    Solids such as char, ash, and refractory organic compounds are removed from coal-derived liquids from coal liquefaction processes by the pressure precoat filtration method using particles of 85-350 mesh material selected from the group of bituminous coal, anthracite coal, lignite, and devolatilized coals as precoat materials and as body feed to the unfiltered coal-derived liquid.

  15. Unstructured mesh generation and adaptivity

    NASA Technical Reports Server (NTRS)

    Mavriplis, D. J.

    1995-01-01

    An overview of current unstructured mesh generation and adaptivity techniques is given. Basic building blocks taken from the field of computational geometry are first described. Various practical mesh generation techniques based on these algorithms are then constructed and illustrated with examples. Issues of adaptive meshing and stretched mesh generation for anisotropic problems are treated in subsequent sections. The presentation is organized in an education manner, for readers familiar with computational fluid dynamics, wishing to learn more about current unstructured mesh techniques.

  16. 49 CFR 192.325 - Underground clearance.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Lines and Mains § 192.325 Underground clearance. (a) Each transmission line must be installed with at... the transmission line. If this clearance cannot be attained, the transmission line must be protected... the requirements of paragraph (a) or (b) of this section, each plastic transmission line or main...

  17. 49 CFR 192.325 - Underground clearance.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Lines and Mains § 192.325 Underground clearance. (a) Each transmission line must be installed with at... the transmission line. If this clearance cannot be attained, the transmission line must be protected... the requirements of paragraph (a) or (b) of this section, each plastic transmission line or main...

  18. 49 CFR 192.325 - Underground clearance.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Lines and Mains § 192.325 Underground clearance. (a) Each transmission line must be installed with at... the transmission line. If this clearance cannot be attained, the transmission line must be protected... the requirements of paragraph (a) or (b) of this section, each plastic transmission line or main...

  19. 20 CFR 325.1 - General.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ...' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.1 General. (a) Day of unemployment. A “day of unemployment.... The amount of compensable days of unemployment shall be computed in accordance with this section....

  20. 20 CFR 325.6 - Verification procedures.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.6 Verification procedures. The Board's procedures for adjudicating and processing applications and claims for unemployment benefits filed pursuant to this part...

  1. 20 CFR 325.1 - General.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ...' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.1 General. (a) Day of unemployment. A “day of unemployment.... The amount of compensable days of unemployment shall be computed in accordance with this section....

  2. 20 CFR 325.6 - Verification procedures.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.6 Verification procedures. The Board's procedures for adjudicating and processing applications and claims for unemployment benefits filed pursuant to this part...

  3. 20 CFR 325.6 - Verification procedures.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.6 Verification procedures. The Board's procedures for adjudicating and processing applications and claims for unemployment benefits filed pursuant to this part...

  4. 20 CFR 325.1 - General.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ...' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.1 General. (a) Day of unemployment. A “day of unemployment.... The amount of compensable days of unemployment shall be computed in accordance with this section....

  5. 20 CFR 325.1 - General.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ...' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.1 General. (a) Day of unemployment. A “day of unemployment.... The amount of compensable days of unemployment shall be computed in accordance with this section....

  6. 20 CFR 325.6 - Verification procedures.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.6 Verification procedures. The Board's procedures for adjudicating and processing applications and claims for unemployment benefits filed pursuant to this part...

  7. 12 CFR 325.202 - Definitions.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... MAINTENANCE Annual Stress Test § 325.202 Definitions. For purposes of this subpart— (a) Adverse scenario means... appropriate for use in the company-run stress tests, including, but not limited to, baseline, adverse, and... of the Federal Deposit Insurance Act (12 U.S.C. 1813). (l) Stress test means the process to...

  8. 12 CFR 325.203 - Applicability.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... MAINTENANCE Annual Stress Test § 325.203 Applicability. (a) First stress test for covered banks subject to stress testing requirements as of October 15, 2012. (1) A $10 billion to $50 billion covered bank as of October 15, 2012 must conduct its first stress test under this subpart using financial statement data...

  9. 12 CFR 325.202 - Definitions.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... MAINTENANCE Annual Stress Test § 325.202 Definitions. For purposes of this subpart— (a) Adverse scenario means... appropriate for use in the company-run stress tests, including, but not limited to, baseline, adverse, and... of the Federal Deposit Insurance Act (12 U.S.C. 1813). (l) Stress test means the process to...

  10. 12 CFR 325.203 - Applicability.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... MAINTENANCE Annual Stress Test § 325.203 Applicability. (a) First stress test for covered banks subject to stress testing requirements as of October 15, 2012. (1) A $10 billion to $50 billion covered bank as of October 15, 2012 must conduct its first stress test under this subpart using financial statement data...

  11. 12 CFR 325.1 - Scope.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... an insured depository institution's capital structure. The FDIC is required to evaluate capital... FEDERAL DEPOSIT INSURANCE CORPORATION REGULATIONS AND STATEMENTS OF GENERAL POLICY CAPITAL MAINTENANCE Minimum Capital Requirements § 325.1 Scope. The provisions of this subpart A apply to those...

  12. 12 CFR 325.1 - Scope.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... an insured depository institution's capital structure. The FDIC is required to evaluate capital... FEDERAL DEPOSIT INSURANCE CORPORATION REGULATIONS AND STATEMENTS OF GENERAL POLICY CAPITAL MAINTENANCE Minimum Capital Requirements § 325.1 Scope. The provisions of this subpart A apply to those...

  13. 20 CFR 325.6 - Verification procedures.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.6 Verification procedures. The Board's procedures for adjudicating and processing applications and claims for unemployment benefits filed pursuant to this part...

  14. 7 CFR 58.325 - Anhydrous milkfat.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... Material § 58.325 Anhydrous milkfat. If cream is used in the production of anhydrous milkfat that is... directly from milk or cream. The cream used shall be comparable to the flavor quality specified above for U.S. Grade AA or U.S. Grade A butter. The milkfat from cream may then be further concentrated into...

  15. 7 CFR 58.325 - Anhydrous milkfat.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... Material § 58.325 Anhydrous milkfat. If cream is used in the production of anhydrous milkfat that is... directly from milk or cream. The cream used shall be comparable to the flavor quality specified above for U.S. Grade AA or U.S. Grade A butter. The milkfat from cream may then be further concentrated into...

  16. 7 CFR 58.325 - Anhydrous milkfat.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... Material § 58.325 Anhydrous milkfat. If cream is used in the production of anhydrous milkfat that is... directly from milk or cream. The cream used shall be comparable to the flavor quality specified above for U.S. Grade AA or U.S. Grade A butter. The milkfat from cream may then be further concentrated into...

  17. 9 CFR 3.25 - Facilities, general.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... WELFARE STANDARDS Specifications for the Humane Handling, Care, Treatment, and Transportation of Guinea Pigs and Hamsters Facilities and Operating Standards § 3.25 Facilities, general. (a) Structural strength. Indoor and outdoor housing facilities for guinea pigs or hamsters shall be structurally sound...

  18. 9 CFR 3.25 - Facilities, general.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... WELFARE STANDARDS Specifications for the Humane Handling, Care, Treatment, and Transportation of Guinea Pigs and Hamsters Facilities and Operating Standards § 3.25 Facilities, general. (a) Structural strength. Indoor and outdoor housing facilities for guinea pigs or hamsters shall be structurally sound...

  19. Cosmology on a Mesh

    NASA Astrophysics Data System (ADS)

    Gill, Stuart P. D.; Knebe, Alexander; Gibson, Brad K.; Flynn, Chris; Ibata, Rodrigo A.; Lewis, Geraint F.

    2003-04-01

    An adaptive multi grid approach to simulating the formation of structure from collisionless dark matter is described. MLAPM (Multi-Level Adaptive Particle Mesh) is one of the most efficient serial codes available on the cosmological "market" today. As part of Swinburne University's role in the development of the Square Kilometer Array, we are implementing hydrodynamics, feedback, and radiative transfer within the MLAPM adaptive mesh, in order to simulate baryonic processes relevant to the interstellar and intergalactic media at high redshift. We will outline our progress to date in applying the existing MLAPM to a study of the decay of satellite galaxies within massive host potentials.

  20. Documentation for MeshKit - Reactor Geometry (&mesh) Generator

    SciTech Connect

    Jain, Rajeev; Mahadevan, Vijay

    2015-09-30

    This report gives documentation for using MeshKit’s Reactor Geometry (and mesh) Generator (RGG) GUI and also briefly documents other algorithms and tools available in MeshKit. RGG is a program designed to aid in modeling and meshing of complex/large hexagonal and rectilinear reactor cores. RGG uses Argonne’s SIGMA interfaces, Qt and VTK to produce an intuitive user interface. By integrating a 3D view of the reactor with the meshing tools and combining them into one user interface, RGG streamlines the task of preparing a simulation mesh and enables real-time feedback that reduces accidental scripting mistakes that could waste hours of meshing. RGG interfaces with MeshKit tools to consolidate the meshing process, meaning that going from model to mesh is as easy as a button click. This report is designed to explain RGG v 2.0 interface and provide users with the knowledge and skills to pilot RGG successfully. Brief documentation of MeshKit source code, tools and other algorithms available are also presented for developers to extend and add new algorithms to MeshKit. RGG tools work in serial and parallel and have been used to model complex reactor core models consisting of conical pins, load pads, several thousands of axially varying material properties of instrumentation pins and other interstices meshes.

  1. Geometric approaches to mesh generation

    SciTech Connect

    Hoffmann, C.M.

    1995-12-31

    We review three approaches to mesh generation that axe based on analyzing and accounting for the geometric structure of the domain. In the first approach, due to Armstrong, the domain is partitioned into subdomains based on the medial-axis transform, a tool for analyzing spatial structures. In the second approach, due to Cox, the design history defines a geometric structure of the domain. The design primitives of that structure are meshed separately, and mesh overlap is accounted for by coupling equations. The third approach argues that mesh generation ought to be integrated into the shape design process, by meshing design features separately and resolving overlapping meshes by standard geometric computations.

  2. Curved mesh generation and mesh refinement using Lagrangian solid mechanics

    SciTech Connect

    Persson, P.-O.; Peraire, J.

    2008-12-31

    We propose a method for generating well-shaped curved unstructured meshes using a nonlinear elasticity analogy. The geometry of the domain to be meshed is represented as an elastic solid. The undeformed geometry is the initial mesh of linear triangular or tetrahedral elements. The external loading results from prescribing a boundary displacement to be that of the curved geometry, and the final configuration is determined by solving for the equilibrium configuration. The deformations are represented using piecewise polynomials within each element of the original mesh. When the mesh is sufficiently fine to resolve the solid deformation, this method guarantees non-intersecting elements even for highly distorted or anisotropic initial meshes. We describe the method and the solution procedures, and we show a number of examples of two and three dimensional simplex meshes with curved boundaries. We also demonstrate how to use the technique for local refinement of non-curved meshes in the presence of curved boundaries.

  3. 42 CFR 426. 325 - What may be challenged.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 42 Public Health 3 2011-10-01 2011-10-01 false What may be challenged. 426. 325 Section 426. 325 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES... General Provisions for the Review of LCDs and NCDs § 426. 325 What may be challenged. (a) Only LCDs...

  4. 42 CFR 426. 325 - What may be challenged.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 3 2010-10-01 2010-10-01 false What may be challenged. 426. 325 Section 426. 325 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES... General Provisions for the Review of LCDs and NCDs § 426. 325 What may be challenged. (a) Only LCDs...

  5. 33 CFR 325.2 - Processing of applications.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 3 2012-07-01 2012-07-01 false Processing of applications. 325.2 Section 325.2 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE PROCESSING OF DEPARTMENT OF THE ARMY PERMITS § 325.2 Processing of applications. (a) Standard procedures. (1) When an application for...

  6. 33 CFR 325.4 - Conditioning of permits.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 3 2013-07-01 2013-07-01 false Conditioning of permits. 325.4 Section 325.4 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE PROCESSING OF DEPARTMENT OF THE ARMY PERMITS § 325.4 Conditioning of permits. (a) District engineers will add special conditions...

  7. 33 CFR 325.4 - Conditioning of permits.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 3 2012-07-01 2012-07-01 false Conditioning of permits. 325.4 Section 325.4 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE PROCESSING OF DEPARTMENT OF THE ARMY PERMITS § 325.4 Conditioning of permits. (a) District engineers will add special conditions...

  8. 20 CFR 325.4 - Claim for unemployment benefits.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Claim for unemployment benefits. 325.4 Section 325.4 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.4 Claim for unemployment benefits. (a) Requirement. After an unemployed employee...

  9. 45 CFR 3.25 - Servicing of vehicles.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 45 Public Welfare 1 2012-10-01 2012-10-01 false Servicing of vehicles. 3.25 Section 3.25 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CONDUCT OF PERSONS AND TRAFFIC ON THE NATIONAL INSTITUTES OF HEALTH FEDERAL ENCLAVE Traffic Regulations § 3.25 Servicing of vehicles....

  10. 45 CFR 3.25 - Servicing of vehicles.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 45 Public Welfare 1 2014-10-01 2014-10-01 false Servicing of vehicles. 3.25 Section 3.25 Public Welfare Department of Health and Human Services GENERAL ADMINISTRATION CONDUCT OF PERSONS AND TRAFFIC ON THE NATIONAL INSTITUTES OF HEALTH FEDERAL ENCLAVE Traffic Regulations § 3.25 Servicing of vehicles....

  11. 45 CFR 3.25 - Servicing of vehicles.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 45 Public Welfare 1 2010-10-01 2010-10-01 false Servicing of vehicles. 3.25 Section 3.25 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CONDUCT OF PERSONS AND TRAFFIC ON THE NATIONAL INSTITUTES OF HEALTH FEDERAL ENCLAVE Traffic Regulations § 3.25 Servicing of vehicles....

  12. 45 CFR 3.25 - Servicing of vehicles.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 45 Public Welfare 1 2011-10-01 2011-10-01 false Servicing of vehicles. 3.25 Section 3.25 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CONDUCT OF PERSONS AND TRAFFIC ON THE NATIONAL INSTITUTES OF HEALTH FEDERAL ENCLAVE Traffic Regulations § 3.25 Servicing of vehicles....

  13. 45 CFR 3.25 - Servicing of vehicles.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 45 Public Welfare 1 2013-10-01 2013-10-01 false Servicing of vehicles. 3.25 Section 3.25 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION CONDUCT OF PERSONS AND TRAFFIC ON THE NATIONAL INSTITUTES OF HEALTH FEDERAL ENCLAVE Traffic Regulations § 3.25 Servicing of vehicles....

  14. 49 CFR 325.7 - Allowable noise levels.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... is based on motor carrier noise emission requirements specified in 40 CFR 202.20 and 40 CFR 202.21. ... 49 Transportation 5 2010-10-01 2010-10-01 false Allowable noise levels. 325.7 Section 325.7... EMISSION STANDARDS General Provisions § 325.7 Allowable noise levels. Motor vehicle noise emissions,...

  15. 24 CFR 1006.325 - Maintenance, management and efficient operation.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... § 1006.325 Maintenance, management and efficient operation. (a) Written policies. The DHHL must develop... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Maintenance, management and efficient operation. 1006.325 Section 1006.325 Housing and Urban Development Regulations Relating to...

  16. 20 CFR 325.5 - Death of employee.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Death of employee. 325.5 Section 325.5 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.5 Death of employee. If an employee dies before...

  17. 12 CFR 325.104 - Capital restoration plans.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 5 2014-01-01 2014-01-01 false Capital restoration plans. 325.104 Section 325... POLICY CAPITAL MAINTENANCE Prompt Corrective Action § 325.104 Capital restoration plans. (a) Schedule for filing plan—(1) In general. A bank shall file a written capital restoration plan with the...

  18. 20 CFR 325.5 - Death of employee.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 20 Employees' Benefits 1 2012-04-01 2012-04-01 false Death of employee. 325.5 Section 325.5 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.5 Death of employee. If an employee dies before...

  19. 20 CFR 325.5 - Death of employee.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 20 Employees' Benefits 1 2014-04-01 2012-04-01 true Death of employee. 325.5 Section 325.5 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.5 Death of employee. If an employee dies before...

  20. 20 CFR 325.5 - Death of employee.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 20 Employees' Benefits 1 2013-04-01 2012-04-01 true Death of employee. 325.5 Section 325.5 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.5 Death of employee. If an employee dies before...

  1. 20 CFR 325.5 - Death of employee.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 20 Employees' Benefits 1 2011-04-01 2011-04-01 false Death of employee. 325.5 Section 325.5 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.5 Death of employee. If an employee dies before...

  2. 12 CFR 603.325 - Special procedures for medical records.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 7 2012-01-01 2012-01-01 false Special procedures for medical records. 603.325 Section 603.325 Banks and Banking FARM CREDIT ADMINISTRATION ADMINISTRATIVE PROVISIONS PRIVACY ACT REGULATIONS § 603.325 Special procedures for medical records. Medical records in the custody of the...

  3. 12 CFR 603.325 - Special procedures for medical records.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Special procedures for medical records. 603.325 Section 603.325 Banks and Banking FARM CREDIT ADMINISTRATION ADMINISTRATIVE PROVISIONS PRIVACY ACT REGULATIONS § 603.325 Special procedures for medical records. Medical records in the custody of the...

  4. 12 CFR 603.325 - Special procedures for medical records.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 7 2014-01-01 2014-01-01 false Special procedures for medical records. 603.325 Section 603.325 Banks and Banking FARM CREDIT ADMINISTRATION ADMINISTRATIVE PROVISIONS PRIVACY ACT REGULATIONS § 603.325 Special procedures for medical records. Medical records in the custody of the...

  5. 12 CFR 603.325 - Special procedures for medical records.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 7 2013-01-01 2013-01-01 false Special procedures for medical records. 603.325 Section 603.325 Banks and Banking FARM CREDIT ADMINISTRATION ADMINISTRATIVE PROVISIONS PRIVACY ACT REGULATIONS § 603.325 Special procedures for medical records. Medical records in the custody of the...

  6. 12 CFR 603.325 - Special procedures for medical records.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 6 2011-01-01 2011-01-01 false Special procedures for medical records. 603.325 Section 603.325 Banks and Banking FARM CREDIT ADMINISTRATION ADMINISTRATIVE PROVISIONS PRIVACY ACT REGULATIONS § 603.325 Special procedures for medical records. Medical records in the custody of the...

  7. 12 CFR 611.325 - Bank and association nominating committees.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 6 2011-01-01 2011-01-01 false Bank and association nominating committees. 611.325 Section 611.325 Banks and Banking FARM CREDIT ADMINISTRATION FARM CREDIT SYSTEM ORGANIZATION Election of Directors and Other Voting Procedures § 611.325 Bank and association nominating...

  8. 12 CFR 611.325 - Bank and association nominating committees.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 7 2014-01-01 2014-01-01 false Bank and association nominating committees. 611.325 Section 611.325 Banks and Banking FARM CREDIT ADMINISTRATION FARM CREDIT SYSTEM ORGANIZATION Election of Directors and Other Voting Procedures § 611.325 Bank and association nominating...

  9. 12 CFR 611.325 - Bank and association nominating committees.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 7 2013-01-01 2013-01-01 false Bank and association nominating committees. 611.325 Section 611.325 Banks and Banking FARM CREDIT ADMINISTRATION FARM CREDIT SYSTEM ORGANIZATION Election of Directors and Other Voting Procedures § 611.325 Bank and association nominating...

  10. 20 CFR 325.4 - Claim for unemployment benefits.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 20 Employees' Benefits 1 2012-04-01 2012-04-01 false Claim for unemployment benefits. 325.4 Section 325.4 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.4 Claim for unemployment benefits....

  11. 20 CFR 325.4 - Claim for unemployment benefits.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 20 Employees' Benefits 1 2014-04-01 2012-04-01 true Claim for unemployment benefits. 325.4 Section 325.4 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.4 Claim for unemployment benefits....

  12. 20 CFR 325.4 - Claim for unemployment benefits.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 20 Employees' Benefits 1 2013-04-01 2012-04-01 true Claim for unemployment benefits. 325.4 Section 325.4 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.4 Claim for unemployment benefits....

  13. 6 CFR 27.325 - Burden of proof.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 6 Domestic Security 1 2012-01-01 2012-01-01 false Burden of proof. 27.325 Section 27.325 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS Orders and Adjudications § 27.325 Burden of proof. The Assistant Secretary bears the...

  14. 6 CFR 27.325 - Burden of proof.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 6 Domestic Security 1 2014-01-01 2014-01-01 false Burden of proof. 27.325 Section 27.325 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS Orders and Adjudications § 27.325 Burden of proof. The Assistant Secretary bears the...

  15. 6 CFR 27.325 - Burden of proof.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 6 Domestic Security 1 2013-01-01 2013-01-01 false Burden of proof. 27.325 Section 27.325 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS Orders and Adjudications § 27.325 Burden of proof. The Assistant Secretary bears the...

  16. 6 CFR 27.325 - Burden of proof.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 6 Domestic Security 1 2011-01-01 2011-01-01 false Burden of proof. 27.325 Section 27.325 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS Orders and Adjudications § 27.325 Burden of proof. The Assistant Secretary bears the...

  17. 6 CFR 27.325 - Burden of proof.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 6 Domestic Security 1 2010-01-01 2010-01-01 false Burden of proof. 27.325 Section 27.325 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS Orders and Adjudications § 27.325 Burden of proof. The Assistant Secretary bears the...

  18. 20 CFR 325.4 - Claim for unemployment benefits.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 20 Employees' Benefits 1 2011-04-01 2011-04-01 false Claim for unemployment benefits. 325.4 Section 325.4 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.4 Claim for unemployment benefits....

  19. 47 CFR 27.322-27.325 - [Reserved

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 2 2011-10-01 2011-10-01 false 27.322-27.325 Section 27.322-27.325 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES Application, Licensing, and Processing Rules for WCS §§ 27.322-27.325...

  20. 47 CFR 27.322-27.325 - [Reserved

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false 27.322-27.325 Section 27.322-27.325 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES Application, Licensing, and Processing Rules for WCS §§ 27.322-27.325...

  1. 21 CFR 172.325 - Bakers yeast protein.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Bakers yeast protein. 172.325 Section 172.325 Food... Special Dietary and Nutritional Additives § 172.325 Bakers yeast protein. Bakers yeast protein may be safely used in food in accordance with the following conditions: (a) Bakers yeast protein is...

  2. 21 CFR 172.325 - Bakers yeast protein.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Bakers yeast protein. 172.325 Section 172.325 Food... Special Dietary and Nutritional Additives § 172.325 Bakers yeast protein. Bakers yeast protein may be safely used in food in accordance with the following conditions: (a) Bakers yeast protein is...

  3. 21 CFR 172.325 - Bakers yeast protein.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Bakers yeast protein. 172.325 Section 172.325 Food... Special Dietary and Nutritional Additives § 172.325 Bakers yeast protein. Bakers yeast protein may be safely used in food in accordance with the following conditions: (a) Bakers yeast protein is...

  4. 21 CFR 172.325 - Bakers yeast protein.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Bakers yeast protein. 172.325 Section 172.325 Food... Additives § 172.325 Bakers yeast protein. Bakers yeast protein may be safely used in food in accordance with the following conditions: (a) Bakers yeast protein is the insoluble proteinaceous material...

  5. 21 CFR 172.325 - Bakers yeast protein.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Bakers yeast protein. 172.325 Section 172.325 Food... Special Dietary and Nutritional Additives § 172.325 Bakers yeast protein. Bakers yeast protein may be safely used in food in accordance with the following conditions: (a) Bakers yeast protein is...

  6. Coal repository. Final report

    SciTech Connect

    Not Available

    1983-11-01

    The Coal Repository Project was initiated in 1980 by the Department of Energy/Pittsburgh Energy Technology Center to provide a centralized system for the collection of well characterized coal samples, and distribution to organizations involved in the chemical beneficiation of coal and related research. TRW Energy Development Group, together with its subcontractor Commercial Testing and Engineering Company, established the Coal Repository at the TRW Capistrano Chemical Facility, which is the location of the DOE-owned Multi-Use Fuel and Energy Processes Test Plant (MEP). Twenty tons each of three coals (Illinois No. 6, Kentucky No. 11 (West), and Pittsburgh No. 8 (from an Ohio mine)) were collected, characterized, and stored under a nitrogen atmosphere. Ten tons of each coal are 3/8-inch x 0, five tons of each are 14-mesh x 0, and five tons of each are 100-mesh x 0. Although TRW was within budget and on schedule, Department of Energy funding priorities in this area were altered such that the project was terminated prior to completion of the original scope of work. 9 figures, 3 tables.

  7. Advanced numerical methods in mesh generation and mesh adaptation

    SciTech Connect

    Lipnikov, Konstantine; Danilov, A; Vassilevski, Y; Agonzal, A

    2010-01-01

    Numerical solution of partial differential equations requires appropriate meshes, efficient solvers and robust and reliable error estimates. Generation of high-quality meshes for complex engineering models is a non-trivial task. This task is made more difficult when the mesh has to be adapted to a problem solution. This article is focused on a synergistic approach to the mesh generation and mesh adaptation, where best properties of various mesh generation methods are combined to build efficiently simplicial meshes. First, the advancing front technique (AFT) is combined with the incremental Delaunay triangulation (DT) to build an initial mesh. Second, the metric-based mesh adaptation (MBA) method is employed to improve quality of the generated mesh and/or to adapt it to a problem solution. We demonstrate with numerical experiments that combination of all three methods is required for robust meshing of complex engineering models. The key to successful mesh generation is the high-quality of the triangles in the initial front. We use a black-box technique to improve surface meshes exported from an unattainable CAD system. The initial surface mesh is refined into a shape-regular triangulation which approximates the boundary with the same accuracy as the CAD mesh. The DT method adds robustness to the AFT. The resulting mesh is topologically correct but may contain a few slivers. The MBA uses seven local operations to modify the mesh topology. It improves significantly the mesh quality. The MBA method is also used to adapt the mesh to a problem solution to minimize computational resources required for solving the problem. The MBA has a solid theoretical background. In the first two experiments, we consider the convection-diffusion and elasticity problems. We demonstrate the optimal reduction rate of the discretization error on a sequence of adaptive strongly anisotropic meshes. The key element of the MBA method is construction of a tensor metric from hierarchical edge

  8. Application of Quaternions for Mesh

    NASA Technical Reports Server (NTRS)

    Samareh, Jamshid A.

    2002-01-01

    A new three dimensional mesh deformation algorithm, based on quaternion algebra, is introduced. A brief overview of quaternion algebra is provided, along with some preliminary results for two-dimensional structured and unstructured viscous mesh deformation.

  9. Multigrid Methods for Mesh Relaxation

    SciTech Connect

    O'Brien, M J

    2006-06-12

    When generating a mesh for the initial conditions for a computer simulation, you want the mesh to be as smooth as possible. A common practice is to use equipotential mesh relaxation to smooth out a distorted computational mesh. Typically a Laplace-like equation is set up for the mesh coordinates and then one or more Jacobi iterations are performed to relax the mesh. As the zone count gets really large, the Jacobi iteration becomes less and less effective and we are stuck with our original unrelaxed mesh. This type of iteration can only damp high frequency errors and the smooth errors remain. When the zone count is large, almost everything looks smooth so relaxation cannot solve the problem. In this paper we examine a multigrid technique which effectively smooths out the mesh, independent of the number of zones.

  10. Toward An Unstructured Mesh Database

    NASA Astrophysics Data System (ADS)

    Rezaei Mahdiraji, Alireza; Baumann, Peter Peter

    2014-05-01

    Unstructured meshes are used in several application domains such as earth sciences (e.g., seismology), medicine, oceanography, cli- mate modeling, GIS as approximate representations of physical objects. Meshes subdivide a domain into smaller geometric elements (called cells) which are glued together by incidence relationships. The subdivision of a domain allows computational manipulation of complicated physical structures. For instance, seismologists model earthquakes using elastic wave propagation solvers on hexahedral meshes. The hexahedral con- tains several hundred millions of grid points and millions of hexahedral cells. Each vertex node in the hexahedrals stores a multitude of data fields. To run simulation on such meshes, one needs to iterate over all the cells, iterate over incident cells to a given cell, retrieve coordinates of cells, assign data values to cells, etc. Although meshes are used in many application domains, to the best of our knowledge there is no database vendor that support unstructured mesh features. Currently, the main tool for querying and manipulating unstructured meshes are mesh libraries, e.g., CGAL and GRAL. Mesh li- braries are dedicated libraries which includes mesh algorithms and can be run on mesh representations. The libraries do not scale with dataset size, do not have declarative query language, and need deep C++ knowledge for query implementations. Furthermore, due to high coupling between the implementations and input file structure, the implementations are less reusable and costly to maintain. A dedicated mesh database offers the following advantages: 1) declarative querying, 2) ease of maintenance, 3) hiding mesh storage structure from applications, and 4) transparent query optimization. To design a mesh database, the first challenge is to define a suitable generic data model for unstructured meshes. We proposed ImG-Complexes data model as a generic topological mesh data model which extends incidence graph model to multi

  11. Surgical mesh for ventral incisional hernia repairs: Understanding mesh design.

    PubMed

    Rastegarpour, Ali; Cheung, Michael; Vardhan, Madhurima; Ibrahim, Mohamed M; Butler, Charles E; Levinson, Howard

    2016-01-01

    Surgical mesh has become an indispensable tool in hernia repair to improve outcomes and reduce costs; however, efforts are constantly being undertaken in mesh development to overcome postoperative complications. Common complications include infection, pain, adhesions, mesh extrusion and hernia recurrence. Reducing the complications of mesh implantation is of utmost importance given that hernias occur in hundreds of thousands of patients per year in the United States. In the present review, the authors present the different types of hernia meshes, discuss the key properties of mesh design, and demonstrate how each design element affects performance and complications. The present article will provide a basis for surgeons to understand which mesh to choose for patient care and why, and will explain the important technological aspects that will continue to evolve over the ensuing years. PMID:27054138

  12. Mesh2d

    SciTech Connect

    Greg Flach, Frank Smith

    2011-12-31

    Mesh2d is a Fortran90 program designed to generate two-dimensional structured grids of the form [x(i),y(i,j)] where [x,y] are grid coordinates identified by indices (i,j). The x(i) coordinates alone can be used to specify a one-dimensional grid. Because the x-coordinates vary only with the i index, a two-dimensional grid is composed in part of straight vertical lines. However, the nominally horizontal y(i,j0) coordinates along index i are permitted to undulate or otherwise vary. Mesh2d also assigns an integer material type to each grid cell, mtyp(i,j), in a user-specified manner. The complete grid is specified through three separate input files defining the x(i), y(i,j), and mtyp(i,j) variations.

  13. Mesh2d

    2011-12-31

    Mesh2d is a Fortran90 program designed to generate two-dimensional structured grids of the form [x(i),y(i,j)] where [x,y] are grid coordinates identified by indices (i,j). The x(i) coordinates alone can be used to specify a one-dimensional grid. Because the x-coordinates vary only with the i index, a two-dimensional grid is composed in part of straight vertical lines. However, the nominally horizontal y(i,j0) coordinates along index i are permitted to undulate or otherwise vary. Mesh2d also assignsmore » an integer material type to each grid cell, mtyp(i,j), in a user-specified manner. The complete grid is specified through three separate input files defining the x(i), y(i,j), and mtyp(i,j) variations.« less

  14. SUPERIMPOSED MESH PLOTTING IN MCNP

    SciTech Connect

    J. HENDRICKS

    2001-02-01

    The capability to plot superimposed meshes has been added to MCNP{trademark}. MCNP4C featured a superimposed mesh weight window generator which enabled users to set up geometries without having to subdivide geometric cells for variance reduction. The variance reduction was performed with weight windows on a rectangular or cylindrical mesh superimposed over the physical geometry. Experience with the new capability was favorable but also indicated that a number of enhancements would be very beneficial, particularly a means of visualizing the mesh and its values. The mathematics for plotting the mesh and its values is described here along with a description of other upgrades.

  15. Particle-mesh techniques

    NASA Technical Reports Server (NTRS)

    Macneice, Peter

    1995-01-01

    This is an introduction to numerical Particle-Mesh techniques, which are commonly used to model plasmas, gravitational N-body systems, and both compressible and incompressible fluids. The theory behind this approach is presented, and its practical implementation, both for serial and parallel machines, is discussed. This document is based on a four-hour lecture course presented by the author at the NASA Summer School for High Performance Computational Physics, held at Goddard Space Flight Center.

  16. Parallel Adaptive Mesh Refinement

    SciTech Connect

    Diachin, L; Hornung, R; Plassmann, P; WIssink, A

    2005-03-04

    As large-scale, parallel computers have become more widely available and numerical models and algorithms have advanced, the range of physical phenomena that can be simulated has expanded dramatically. Many important science and engineering problems exhibit solutions with localized behavior where highly-detailed salient features or large gradients appear in certain regions which are separated by much larger regions where the solution is smooth. Examples include chemically-reacting flows with radiative heat transfer, high Reynolds number flows interacting with solid objects, and combustion problems where the flame front is essentially a two-dimensional sheet occupying a small part of a three-dimensional domain. Modeling such problems numerically requires approximating the governing partial differential equations on a discrete domain, or grid. Grid spacing is an important factor in determining the accuracy and cost of a computation. A fine grid may be needed to resolve key local features while a much coarser grid may suffice elsewhere. Employing a fine grid everywhere may be inefficient at best and, at worst, may make an adequately resolved simulation impractical. Moreover, the location and resolution of fine grid required for an accurate solution is a dynamic property of a problem's transient features and may not be known a priori. Adaptive mesh refinement (AMR) is a technique that can be used with both structured and unstructured meshes to adjust local grid spacing dynamically to capture solution features with an appropriate degree of resolution. Thus, computational resources can be focused where and when they are needed most to efficiently achieve an accurate solution without incurring the cost of a globally-fine grid. Figure 1.1 shows two example computations using AMR; on the left is a structured mesh calculation of a impulsively-sheared contact surface and on the right is the fuselage and volume discretization of an RAH-66 Comanche helicopter [35]. Note the

  17. On Optimal Bilinear Quadrilateral Meshes

    SciTech Connect

    D'Azevedo, E.

    1998-10-26

    The novelty of this work is in presenting interesting error properties of two types of asymptotically optimal quadrilateral meshes for bilinear approximation. The first type of mesh has an error equidistributing property where the maximum interpolation error is asymptotically the same over all elements. The second type has faster than expected super-convergence property for certain saddle-shaped data functions. The super-convergent mesh may be an order of magnitude more accurate than the error equidistributing mesh. Both types of mesh are generated by a coordinate transformation of a regular mesh of squares. The coordinate transformation is derived by interpreting the Hessian matrix of a data function as a metric tensor. The insights in this work may have application in mesh design near known corner or point singularities.

  18. On Optimal Bilinear Quadrilateral Meshes

    SciTech Connect

    D'Azevedo, E

    2000-03-17

    The novelty of this work is in presenting interesting error properties of two types of asymptotically ''optimal'' quadrilateral meshes for bilinear approximation. The first type of mesh has an error equidistributing property where the maximum interpolation error is asymptotically the same over all elements. The second type has faster than expected ''super-convergence'' property for certain saddle-shaped data functions. The ''superconvergent'' mesh may be an order of magnitude more accurate than the error equidistributing mesh. Both types of mesh are generated by a coordinate transformation of a regular mesh of squares. The coordinate transformation is derived by interpreting the Hessian matrix of a data function as a metric tensor. The insights in this work may have application in mesh design near corner or point singularities.

  19. ASSESSMENT OF COAL CLEANING TECHNOLOGY: FINAL REPORT

    EPA Science Inventory

    The report gives results of tests at seven coal preparation plants to evaluate the performance of froth flotation cells and dense-medium cyclones in removing ash and sulfur (S) from fine coal (Minus 28 mesh). Flotation circuits tested at four plants showed substantial reductions ...

  20. Mesh Algorithms for PDE with Sieve I: Mesh Distribution

    DOE PAGESBeta

    Knepley, Matthew G.; Karpeev, Dmitry A.

    2009-01-01

    We have developed a new programming framework, called Sieve, to support parallel numerical partial differential equation(s) (PDE) algorithms operating over distributed meshes. We have also developed a reference implementation of Sieve in C++ as a library of generic algorithms operating on distributed containers conforming to the Sieve interface. Sieve makes instances of the incidence relation, or arrows, the conceptual first-class objects represented in the containers. Further, generic algorithms acting on this arrow container are systematically used to provide natural geometric operations on the topology and also, through duality, on the data. Finally, coverings and duality are used to encode notmore » only individual meshes, but all types of hierarchies underlying PDE data structures, including multigrid and mesh partitions. In order to demonstrate the usefulness of the framework, we show how the mesh partition data can be represented and manipulated using the same fundamental mechanisms used to represent meshes. We present the complete description of an algorithm to encode a mesh partition and then distribute a mesh, which is independent of the mesh dimension, element shape, or embedding. Moreover, data associated with the mesh can be similarly distributed with exactly the same algorithm. The use of a high level of abstraction within the Sieve leads to several benefits in terms of code reuse, simplicity, and extensibility. We discuss these benefits and compare our approach to other existing mesh libraries.« less

  1. Mesh Oriented datABase

    SciTech Connect

    Tautges, Timothy J.

    2004-04-01

    MOAB is a component for representing and evaluating mesh data. MOAB can store stuctured and unstructured mesh, consisting of elements in the finite element "zoo". The functional interface to MOAB is simple yet powerful, allowing the representation of many types of metadata commonly found on the mesh. MOAB is optimized for efficiency in space and time, based on access to mesh in chunks rather than through individual entities, while also versatile enough to support individual entity access. The MOAB data model consists of a mesh interface instance, mesh entities (vertices and elements), sets, and tags. Entities are addressed through handles rather than pointers, to allow the underlying representation of an entity to change without changing the handle to that entity. Sets are arbitrary groupings of mesh entities and other sets. Sets also support parent/child relationships as a relation distinct from sets containing other sets. The directed-graph provided by set parent/child relationships is useful for modeling topological relations from a geometric model or other metadata. Tags are named data which can be assigned to the mesh as a whole, individual entities, or sets. Tags are a mechanism for attaching data to individual entities and sets are a mechanism for describing relations between entities; the combination of these two mechanisms isa powerful yet simple interface for representing metadata or application-specific data. For example, sets and tags can be used together to describe geometric topology, boundary condition, and inter-processor interface groupings in a mesh. MOAB is used in several ways in various applications. MOAB serves as the underlying mesh data representation in the VERDE mesh verification code. MOAB can also be used as a mesh input mechanism, using mesh readers induded with MOAB, or as a t’anslator between mesh formats, using readers and writers included with MOAB.

  2. Mesh Oriented datABase

    2004-04-01

    MOAB is a component for representing and evaluating mesh data. MOAB can store stuctured and unstructured mesh, consisting of elements in the finite element "zoo". The functional interface to MOAB is simple yet powerful, allowing the representation of many types of metadata commonly found on the mesh. MOAB is optimized for efficiency in space and time, based on access to mesh in chunks rather than through individual entities, while also versatile enough to support individualmore » entity access. The MOAB data model consists of a mesh interface instance, mesh entities (vertices and elements), sets, and tags. Entities are addressed through handles rather than pointers, to allow the underlying representation of an entity to change without changing the handle to that entity. Sets are arbitrary groupings of mesh entities and other sets. Sets also support parent/child relationships as a relation distinct from sets containing other sets. The directed-graph provided by set parent/child relationships is useful for modeling topological relations from a geometric model or other metadata. Tags are named data which can be assigned to the mesh as a whole, individual entities, or sets. Tags are a mechanism for attaching data to individual entities and sets are a mechanism for describing relations between entities; the combination of these two mechanisms isa powerful yet simple interface for representing metadata or application-specific data. For example, sets and tags can be used together to describe geometric topology, boundary condition, and inter-processor interface groupings in a mesh. MOAB is used in several ways in various applications. MOAB serves as the underlying mesh data representation in the VERDE mesh verification code. MOAB can also be used as a mesh input mechanism, using mesh readers induded with MOAB, or as a t’anslator between mesh formats, using readers and writers included with MOAB.« less

  3. Experience dewatering fine coal in solidbowl centrifuges at the York Canyon preparation plant

    SciTech Connect

    Alderman, J.K.

    1995-08-01

    In 1990, a study was undertaken at P&M`s York Canyon preparation plant to evaluate options for dewatering froth flotation product. The existing vacuum disc filter was in need of replacement from wear and neglect, and analysis of the feed to the filter showed that only 7% of the particles were larger than 0.15mm (100 mesh) while nearly 60% of the particles were finer than 0.45mm (325 mesh). Size analysis of the filter cake indicated a mass mean diameter (MMD) of 0.092mm and surface moisture of the filter cake was 33%. Preliminary modeling indicated that a surface moisture of 26% might be attainable for this cake with efficient mechanical dewatering. Based upon the fineness of the feed and the need to replace the filter, in 1991 P&M conducted the field testing with a pilot-scale Sharples high-G solidbowl centrifuge. Data from the pilot scale tests led to the conclusion that the solidbowl centrifuges could recover over 90% of feed solids while providing a surface moisture of about 25% in the product cake. When a decision was made in 1992 to replace the existing plant at York Canyon with a new, larger preparation plant, the commercial scale Sharples high-G solidbowl centrifuges were selected for fine dewatering. The following discussion deals with the plant fine coal dewatering circuitry, start-up problems, remedial actions, and machine dewatering performance.

  4. Method of drying fine coal particles

    SciTech Connect

    Ladt, M.A.

    1984-04-24

    A method of drying wet coal fines smaller than 28 mesh in size employs both a vibrating fluidized bed type dryer and a coal fired burner for supplying hot drying gases to the dryer. A regenerative separator is interposed between the coal fired burner and the fluidized bed type dryer to satisfactorily remove particle matter from the gases without unacceptable pressure losses. Hot gases exhausted from the fluidized bed type dryer are also cleansed to remove particulate coal particles which are used as fuel for the coal fired burner.

  5. toolkit computational mesh conceptual model.

    SciTech Connect

    Baur, David G.; Edwards, Harold Carter; Cochran, William K.; Williams, Alan B.; Sjaardema, Gregory D.

    2010-03-01

    The Sierra Toolkit computational mesh is a software library intended to support massively parallel multi-physics computations on dynamically changing unstructured meshes. This domain of intended use is inherently complex due to distributed memory parallelism, parallel scalability, heterogeneity of physics, heterogeneous discretization of an unstructured mesh, and runtime adaptation of the mesh. Management of this inherent complexity begins with a conceptual analysis and modeling of this domain of intended use; i.e., development of a domain model. The Sierra Toolkit computational mesh software library is designed and implemented based upon this domain model. Software developers using, maintaining, or extending the Sierra Toolkit computational mesh library must be familiar with the concepts/domain model presented in this report.

  6. Cubit Adaptive Meshing Algorithm Library

    2004-09-01

    CAMAL (Cubit adaptive meshing algorithm library) is a software component library for mesh generation. CAMAL 2.0 includes components for triangle, quad and tetrahedral meshing. A simple Application Programmers Interface (API) takes a discrete boundary definition and CAMAL computes a quality interior unstructured grid. The triangle and quad algorithms may also import a geometric definition of a surface on which to define the grid. CAMAL’s triangle meshing uses a 3D space advancing front method, the quadmore » meshing algorithm is based upon Sandia’s patented paving algorithm and the tetrahedral meshing algorithm employs the GHS3D-Tetmesh component developed by INRIA, France.« less

  7. Microbial desulfurization of coal

    SciTech Connect

    Andrews, G.F.; Dugan, P.R.; McIlwain, M.E.; Stevens, C.J.

    1992-03-01

    A bacterial coal depyritization process was operated at a large laboratory scale for four months treating almost 500 kg of an Illinois {number_sign}6 coal supplied by the Monterey Coal Company and ground to 80% minus 100 mesh. The main features of the process were a 200-{ell} aerated trough bioreactor consisting of a channel 2.44 m long with a porous aeration tube running along its V-shaped bottom, an inclined 40 {mu}m screen for dewatering the coal slurry, and a liquid recycle stream to inoculate the incoming coal with the bacteria and ferric ion required for pyrite removal. The process was started up with large numbers of Thiobacillus ferrooxidans and Leptospirillum ferrooxidans bacteria grown on iron media in a specially built electrolysis cell. Natural selection pressures then created a mixed culture well adapted to the coal from these bacteria, smaller numbers of T. thiooxidans added later, and the bacteria carried into the system with the coal. The process was run at 2.0 < pH < 2.7 and 18{degrees}C < temperature < 22{degrees}C.

  8. PMESH: A parallel mesh generator

    SciTech Connect

    Hardin, D.D.

    1994-10-21

    The Parallel Mesh Generation (PMESH) Project is a joint LDRD effort by A Division and Engineering to develop a unique mesh generation system that can construct large calculational meshes (of up to 10{sup 9} elements) on massively parallel computers. Such a capability will remove a critical roadblock to unleashing the power of massively parallel processors (MPPs) for physical analysis. PMESH will support a variety of LLNL 3-D physics codes in the areas of electromagnetics, structural mechanics, thermal analysis, and hydrodynamics.

  9. Multigrid techniques for unstructured meshes

    NASA Technical Reports Server (NTRS)

    Mavriplis, D. J.

    1995-01-01

    An overview of current multigrid techniques for unstructured meshes is given. The basic principles of the multigrid approach are first outlined. Application of these principles to unstructured mesh problems is then described, illustrating various different approaches, and giving examples of practical applications. Advanced multigrid topics, such as the use of algebraic multigrid methods, and the combination of multigrid techniques with adaptive meshing strategies are dealt with in subsequent sections. These represent current areas of research, and the unresolved issues are discussed. The presentation is organized in an educational manner, for readers familiar with computational fluid dynamics, wishing to learn more about current unstructured mesh techniques.

  10. Multigrid for locally refined meshes

    SciTech Connect

    Shapira, Y.

    1999-12-01

    A multilevel method for the solution of finite element schemes on locally refined meshes is introduced. For isotropic diffusion problems, the condition number of the two-level method is bounded independently of the mesh size and the discontinuities in the diffusion coefficient. The curves of discontinuity need not be aligned with the coarse mesh. Indeed, numerical applications with 10 levels of local refinement yield a rapid convergence of the corresponding 10-level, multigrid V-cycle and other multigrid cycles which are more suitable for parallelism even when the discontinuities are invisible on most of the coarse meshes.

  11. Coal surface control for advanced fine coal flotation

    SciTech Connect

    Fuerstenau, D.W.; Sastry, K.V.S.; Hanson, J.S.; Diao, J.; De, A.; Sotillo, F.; Harris, G. ); Somasundaran, P.; Harris, C.C.; Vasudevan, T.; Liu, D.; Li, C. ); Hu, Weibei; Zou, Y.; Chen, W. ); Choudhry, V.; Shea, S.; Ghosh, A.; Sehgal, R. (Praxis Engineers, Inc., Milpitas, CA

    1991-01-15

    The majority of research conducted was designed to control and selectivity modify coal and pyrite surfaces during flotation. Numerous approaches were used as part of the effort to enhance the separation efficiency of the flotation process. These included the addition of emulsifiers, dispersants, xanthated polymers, straight-chained alcohols, calcium cyanides an pH modifiers. The most important finding from these studies are the delineation of the role of pH and the beneficial effects of alcohols on coal flotation. For minus 28-mesh coal, a detailed study of the role of particle size on the kinetics of flotation was undertaken in order to determine flotation rate constants for coal, ash and pyrite particles as a function of particle size. In general, the rate constants for the flotation of coal were found to be higher than those of pyrite and ash and they did not vary substantially with particle size. Characterization studies of weathered and fresh coal samples were also completed. Induction times measured for freshly ground coal were found to indicate the same order of hydrophobicity as determined by contact angle measurements and all other techniques used to assess wettability. DRIFT spectroscopy of weathered coals was not able to detect the effects of weathering while zeta potential measurements showed that the weathered coal had a slightly more negative surface charge. The induction times for the coals generally increased with weathering time. 4 refs., 69 figs., 82 tabs.

  12. Risk Factors for Mesh Exposure after Transvaginal Mesh Surgery

    PubMed Central

    Niu, Ke; Lu, Yong-Xian; Shen, Wen-Jie; Zhang, Ying-Hui; Wang, Wen-Ying

    2016-01-01

    Background: Mesh exposure after surgery continues to be a clinical challenge for urogynecological surgeons. The purpose of this study was to explore the risk factors for polypropylene (PP) mesh exposure after transvaginal mesh (TVM) surgery. Methods: This study included 195 patients with advanced pelvic organ prolapse (POP), who underwent TVM from January 2004 to December 2012 at the First Affiliated Hospital of Chinese PLA General Hospital. Clinical data were evaluated including patient's demography, TVM type, concomitant procedures, operation time, blood loss, postoperative morbidity, and mesh exposure. Mesh exposure was identified through postoperative vaginal examination. Statistical analysis was performed to identify risk factors for mesh exposure. Results: Two-hundred and nine transvaginal PP meshes were placed, including 194 in the anterior wall and 15 in the posterior wall. Concomitant tension-free vaginal tape was performed in 61 cases. The mean follow-up time was 35.1 ± 23.6 months. PP mesh exposure was identified in 32 cases (16.4%), with 31 in the anterior wall and 1 in the posterior wall. Significant difference was found in operating time and concomitant procedures between exposed and nonexposed groups (F = 7.443, P = 0.007; F = 4.307, P = 0.039, respectively). Binary logistic regression revealed that the number of concomitant procedures and operation time were risk factors for mesh exposure (P = 0.001, P = 0.043). Conclusion: Concomitant procedures and increased operating time increase the risk for postoperative mesh exposure in patients undergoing TVM surgery for POP. PMID:27453227

  13. Invisible metallic mesh

    PubMed Central

    Ye, Dexin; Lu, Ling; Joannopoulos, John D.; Soljačić, Marin; Ran, Lixin

    2016-01-01

    A solid material possessing identical electromagnetic properties as air has yet to be found in nature. Such a medium of arbitrary shape would neither reflect nor refract light at any angle of incidence in free space. Here, we introduce nonscattering corrugated metallic wires to construct such a medium. This was accomplished by aligning the dark-state frequencies in multiple scattering channels of a single wire. Analytical solutions, full-wave simulations, and microwave measurement results on 3D printed samples show omnidirectional invisibility in any configuration. This invisible metallic mesh can improve mechanical stability, electrical conduction, and heat dissipation of a system, without disturbing the electromagnetic design. Our approach is simple, robust, and scalable to higher frequencies. PMID:26884208

  14. Invisible metallic mesh.

    PubMed

    Ye, Dexin; Lu, Ling; Joannopoulos, John D; Soljačić, Marin; Ran, Lixin

    2016-03-01

    A solid material possessing identical electromagnetic properties as air has yet to be found in nature. Such a medium of arbitrary shape would neither reflect nor refract light at any angle of incidence in free space. Here, we introduce nonscattering corrugated metallic wires to construct such a medium. This was accomplished by aligning the dark-state frequencies in multiple scattering channels of a single wire. Analytical solutions, full-wave simulations, and microwave measurement results on 3D printed samples show omnidirectional invisibility in any configuration. This invisible metallic mesh can improve mechanical stability, electrical conduction, and heat dissipation of a system, without disturbing the electromagnetic design. Our approach is simple, robust, and scalable to higher frequencies. PMID:26884208

  15. 10 CFR 431.325 - Units to be tested.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 3 2011-01-01 2011-01-01 false Units to be tested. 431.325 Section 431.325 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY PROGRAM FOR CERTAIN COMMERCIAL AND INDUSTRIAL... energy efficiency calculated as the measured output power to the lamp divided by the measured input...

  16. 50 CFR 600.325 - National Standard 4-Allocations.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Section 600.325 Wildlife and Fisheries FISHERY CONSERVATION AND MANAGEMENT, NATIONAL OCEANIC AND....325 National Standard 4—Allocations. (a) Standard 4. Conservation and management measures shall not... fishermen. (2) Reasonably calculated to promote conservation. (3) Carried out in such manner that...

  17. 50 CFR 600.325 - National Standard 4-Allocations.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Section 600.325 Wildlife and Fisheries FISHERY CONSERVATION AND MANAGEMENT, NATIONAL OCEANIC AND....325 National Standard 4—Allocations. (a) Standard 4. Conservation and management measures shall not... fishermen. (2) Reasonably calculated to promote conservation. (3) Carried out in such manner that...

  18. 50 CFR 600.325 - National Standard 4-Allocations.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Section 600.325 Wildlife and Fisheries FISHERY CONSERVATION AND MANAGEMENT, NATIONAL OCEANIC AND....325 National Standard 4—Allocations. (a) Standard 4. Conservation and management measures shall not... fishermen. (2) Reasonably calculated to promote conservation. (3) Carried out in such manner that...

  19. 50 CFR 600.325 - National Standard 4-Allocations.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Section 600.325 Wildlife and Fisheries FISHERY CONSERVATION AND MANAGEMENT, NATIONAL OCEANIC AND....325 National Standard 4—Allocations. (a) Standard 4. Conservation and management measures shall not... fishermen. (2) Reasonably calculated to promote conservation. (3) Carried out in such manner that...

  20. 47 CFR 80.325 - Control of distress traffic.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 5 2014-10-01 2014-10-01 false Control of distress traffic. 80.325 Section 80... Safety Procedures § 80.325 Control of distress traffic. (a) Distress traffic consists of all messages relating to the immediate assistance required by the mobile station in distress. In distress traffic,...

  1. 47 CFR 80.325 - Control of distress traffic.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 5 2011-10-01 2011-10-01 false Control of distress traffic. 80.325 Section 80... Safety Procedures § 80.325 Control of distress traffic. (a) Distress traffic consists of all messages relating to the immediate assistance required by the mobile station in distress. In distress traffic,...

  2. 47 CFR 80.325 - Control of distress traffic.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 5 2012-10-01 2012-10-01 false Control of distress traffic. 80.325 Section 80... Safety Procedures § 80.325 Control of distress traffic. (a) Distress traffic consists of all messages relating to the immediate assistance required by the mobile station in distress. In distress traffic,...

  3. 47 CFR 80.325 - Control of distress traffic.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 5 2013-10-01 2013-10-01 false Control of distress traffic. 80.325 Section 80... Safety Procedures § 80.325 Control of distress traffic. (a) Distress traffic consists of all messages relating to the immediate assistance required by the mobile station in distress. In distress traffic,...

  4. 47 CFR 80.325 - Control of distress traffic.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Control of distress traffic. 80.325 Section 80... Safety Procedures § 80.325 Control of distress traffic. (a) Distress traffic consists of all messages relating to the immediate assistance required by the mobile station in distress. In distress traffic,...

  5. 12 CFR 325.3 - Minimum leverage capital requirement.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 4 2011-01-01 2011-01-01 false Minimum leverage capital requirement. 325.3... GENERAL POLICY CAPITAL MAINTENANCE Minimum Capital Requirements § 325.3 Minimum leverage capital requirement. (a) General. Banks must maintain at least the minimum leverage capital requirement set forth...

  6. 31 CFR 560.325 - Property; property interest.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 31 Money and Finance:Treasury 3 2014-07-01 2014-07-01 false Property; property interest. 560.325... General Definitions § 560.325 Property; property interest. The terms property and property interest..., contracts of any nature whatsoever, and any other property, real, personal, or mixed, tangible or...

  7. 31 CFR 560.325 - Property; property interest.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 31 Money and Finance:Treasury 3 2013-07-01 2013-07-01 false Property; property interest. 560.325... General Definitions § 560.325 Property; property interest. The terms property and property interest..., contracts of any nature whatsoever, and any other property, real, personal, or mixed, tangible or...

  8. 15 CFR 325.16 - Protecting confidentiality of information.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... or employee of the United States shall disclose commercial or financial information submitted under... certificate, if— (A) The Secretary determines that a non-confidential summary of the information is inadequate... information. 325.16 Section 325.16 Commerce and Foreign Trade Regulations Relating to Commerce and...

  9. 49 CFR 325.35 - Ambient conditions; highway operations.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 5 2014-10-01 2014-10-01 false Ambient conditions; highway operations. 325.35... MOTOR CARRIER NOISE EMISSION STANDARDS Measurement of Noise Emissions; Highway Operations § 325.35 Ambient conditions; highway operations. (a)(1) Sound. The ambient A-weighted sound level at the...

  10. 49 CFR 325.35 - Ambient conditions; highway operations.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 5 2013-10-01 2013-10-01 false Ambient conditions; highway operations. 325.35... MOTOR CARRIER NOISE EMISSION STANDARDS Measurement of Noise Emissions; Highway Operations § 325.35 Ambient conditions; highway operations. (a)(1) Sound. The ambient A-weighted sound level at the...

  11. 45 CFR 149.325 - Requirements for eligibility of claims.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Section 149.325 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES REQUIREMENTS RELATING TO HEALTH CARE ACCESS REQUIREMENTS FOR THE EARLY RETIREE REINSURANCE PROGRAM Reimbursement Methods § 149.325 Requirements for eligibility of claims. A claim may be submitted only if it represents costs for...

  12. 24 CFR 891.325 - Lead-based paint requirements.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 4 2012-04-01 2012-04-01 false Lead-based paint requirements. 891.325 Section 891.325 Housing and Urban Development REGULATIONS RELATING TO HOUSING AND URBAN DEVELOPMENT (CONTINUED) OFFICE OF THE ASSISTANT SECRETARY FOR HOUSING-FEDERAL HOUSING COMMISSIONER, DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT (SECTION...

  13. 49 CFR 172.325 - Elevated temperature materials.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Elevated temperature materials. 172.325 Section... REQUIREMENTS, AND SECURITY PLANS Marking § 172.325 Elevated temperature materials. (a) Except as provided in paragraph (b) of this section, a bulk packaging containing an elevated temperature material must be...

  14. 14 CFR 139.325 - Airport emergency plan.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... water or marsh lands adjacent to the airport that are crossed by the approach and departure flight paths... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airport emergency plan. 139.325 Section 139... AIRPORTS Operations § 139.325 Airport emergency plan. (a) In a manner authorized by the Administrator,...

  15. 14 CFR 139.325 - Airport emergency plan.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... water or marsh lands adjacent to the airport that are crossed by the approach and departure flight paths... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airport emergency plan. 139.325 Section 139... AIRPORTS Operations § 139.325 Airport emergency plan. (a) In a manner authorized by the Administrator,...

  16. 14 CFR 139.325 - Airport emergency plan.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... water or marsh lands adjacent to the airport that are crossed by the approach and departure flight paths... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airport emergency plan. 139.325 Section 139... AIRPORTS Operations § 139.325 Airport emergency plan. (a) In a manner authorized by the Administrator,...

  17. 46 CFR 154.325 - Accommodation, service, and control spaces.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Accommodation, service, and control spaces. 154.325... Equipment Ship Arrangements § 154.325 Accommodation, service, and control spaces. (a) Accommodation, service, and control spaces must be outside the cargo area. (b) If a hold space having a cargo...

  18. 40 CFR 1065.325 - Intake-flow calibration.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 33 2011-07-01 2011-07-01 false Intake-flow calibration. 1065.325 Section 1065.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Calibrations and Verifications Flow-Related Measurements §...

  19. 40 CFR 1065.325 - Intake-flow calibration.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Intake-flow calibration. 1065.325 Section 1065.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Calibrations and Verifications Flow-Related Measurements §...

  20. 14 CFR 21.325 - Export airworthiness approvals.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Export airworthiness approvals. 21.325... AIRCRAFT CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS Export Airworthiness Approvals § 21.325 Export airworthiness approvals. (a) Kinds of approvals. (1) Export airworthiness approval of Class I products is...

  1. 49 CFR 325.73 - Microphone distance correction factors. 1

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... factors. 1 1 Table 1, in § 325.7 is a tabulation of the maximum allowable sound level readings taking into... target point is other than 50 feet (15.2 m), the maximum observed sound level reading generated by the... observed sound level readings generated by the motor vehicle in accordance with § 325.59 of this part...

  2. 49 CFR 325.39 - Measurement procedure; highway operations.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 5 2010-10-01 2010-10-01 false Measurement procedure; highway operations. 325.39... MOTOR CARRIER NOISE EMISSION STANDARDS Measurement of Noise Emissions; Highway Operations § 325.39 Measurement procedure; highway operations. (a) In accordance with the rules in this subpart, a...

  3. 49 CFR 325.25 - Calibration of measurement systems.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 5 2010-10-01 2010-10-01 false Calibration of measurement systems. 325.25 Section... CARRIER NOISE EMISSION STANDARDS Instrumentation § 325.25 Calibration of measurement systems. (a)(1) The sound level measurement system must be calibrated and appropriately adjusted at one or more...

  4. 49 CFR 325.25 - Calibration of measurement systems.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 5 2013-10-01 2013-10-01 false Calibration of measurement systems. 325.25 Section... CARRIER NOISE EMISSION STANDARDS Instrumentation § 325.25 Calibration of measurement systems. (a)(1) The sound level measurement system must be calibrated and appropriately adjusted at one or more...

  5. 49 CFR 325.39 - Measurement procedure; highway operations.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 5 2011-10-01 2011-10-01 false Measurement procedure; highway operations. 325.39... MOTOR CARRIER NOISE EMISSION STANDARDS Measurement of Noise Emissions; Highway Operations § 325.39 Measurement procedure; highway operations. (a) In accordance with the rules in this subpart, a...

  6. 49 CFR 325.59 - Measurement procedure; stationary test.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Stationary Test, 40 CFR 202.21. (Table 1 in § 325.7 lists the range of maximum permissible sound level... 49 Transportation 5 2013-10-01 2013-10-01 false Measurement procedure; stationary test. 325.59... MOTOR CARRIER NOISE EMISSION STANDARDS Measurement of Noise Emissions; Stationary Test §...

  7. 49 CFR 325.25 - Calibration of measurement systems.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 5 2011-10-01 2011-10-01 false Calibration of measurement systems. 325.25 Section... CARRIER NOISE EMISSION STANDARDS Instrumentation § 325.25 Calibration of measurement systems. (a)(1) The sound level measurement system must be calibrated and appropriately adjusted at one or more...

  8. 49 CFR 325.39 - Measurement procedure; highway operations.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 5 2013-10-01 2013-10-01 false Measurement procedure; highway operations. 325.39... MOTOR CARRIER NOISE EMISSION STANDARDS Measurement of Noise Emissions; Highway Operations § 325.39 Measurement procedure; highway operations. (a) In accordance with the rules in this subpart, a...

  9. 49 CFR 325.59 - Measurement procedure; stationary test.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Stationary Test, 40 CFR 202.21. (Table 1 in § 325.7 lists the range of maximum permissible sound level... 49 Transportation 5 2010-10-01 2010-10-01 false Measurement procedure; stationary test. 325.59... MOTOR CARRIER NOISE EMISSION STANDARDS Measurement of Noise Emissions; Stationary Test §...

  10. 20 CFR 404.325 - The termination month.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 20 Employees' Benefits 2 2011-04-01 2011-04-01 false The termination month. 404.325 Section 404.325 Employees' Benefits SOCIAL SECURITY ADMINISTRATION FEDERAL OLD-AGE, SURVIVORS AND DISABILITY.... In April 2003, 4 months after your reentitlement period ends, you become employed at work that...

  11. 20 CFR 404.325 - The termination month.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false The termination month. 404.325 Section 404.325 Employees' Benefits SOCIAL SECURITY ADMINISTRATION FEDERAL OLD-AGE, SURVIVORS AND DISABILITY.... In April 2003, 4 months after your reentitlement period ends, you become employed at work that...

  12. 15 CFR 280.325 - Cumulative listing of recordal information.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... information. 280.325 Section 280.325 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY, DEPARTMENT OF COMMERCE ACCREDITATION AND... listing of recordal information. The Director, USPTO, shall maintain a record of the names,...

  13. 49 CFR 172.325 - Elevated temperature materials.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Elevated temperature materials. 172.325 Section... REQUIREMENTS, AND SECURITY PLANS Marking § 172.325 Elevated temperature materials. (a) Except as provided in paragraph (b) of this section, a bulk packaging containing an elevated temperature material must be...

  14. 49 CFR 172.325 - Elevated temperature materials.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Elevated temperature materials. 172.325 Section... REQUIREMENTS, AND SECURITY PLANS Marking § 172.325 Elevated temperature materials. (a) Except as provided in paragraph (b) of this section, a bulk packaging containing an elevated temperature material must be...

  15. 49 CFR 172.325 - Elevated temperature materials.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Elevated temperature materials. 172.325 Section... REQUIREMENTS, AND SECURITY PLANS Marking § 172.325 Elevated temperature materials. (a) Except as provided in paragraph (b) of this section, a bulk packaging containing an elevated temperature material must be...

  16. 49 CFR 172.325 - Elevated temperature materials.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Elevated temperature materials. 172.325 Section... REQUIREMENTS, AND SECURITY PLANS Marking § 172.325 Elevated temperature materials. (a) Except as provided in paragraph (b) of this section, a bulk packaging containing an elevated temperature material must be...

  17. 49 CFR 325.73 - Microphone distance correction factors. 1

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... factors. 1 1 Table 1, in § 325.7 is a tabulation of the maximum allowable sound level readings taking into... target point is other than 50 feet (15.2 m), the maximum observed sound level reading generated by the... observed sound level readings generated by the motor vehicle in accordance with § 325.59 of this part...

  18. 46 CFR 154.325 - Accommodation, service, and control spaces.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 5 2012-10-01 2012-10-01 false Accommodation, service, and control spaces. 154.325 Section 154.325 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Ship Arrangements §...

  19. 16 CFR 3.25 - Consent agreement settlements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Consent agreement settlements. 3.25 Section 3.25 Commercial Practices FEDERAL TRADE COMMISSION ORGANIZATION, PROCEDURES AND RULES OF PRACTICE RULES OF PRACTICE FOR ADJUDICATIVE PROCEEDINGS Prehearing Procedures; Motions; Interlocutory...

  20. 12 CFR 325.207 - Publication of stress test results.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 5 2013-01-01 2013-01-01 false Publication of stress test results. 325.207... GENERAL POLICY CAPITAL MAINTENANCE Annual Stress Test § 325.207 Publication of stress test results. (a... annual stress test in the period starting June 15 and ending June 30. (2) An over $50 billion...

  1. 12 CFR 325.207 - Publication of stress test results.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 5 2014-01-01 2014-01-01 false Publication of stress test results. 325.207... GENERAL POLICY CAPITAL MAINTENANCE Annual Stress Test § 325.207 Publication of stress test results. (a... annual stress test in the period starting June 15 and ending June 30. (2) An over $50 billion...

  2. 12 CFR 325.204 - Annual stress tests required.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 5 2013-01-01 2013-01-01 false Annual stress tests required. 325.204 Section... POLICY CAPITAL MAINTENANCE Annual Stress Test § 325.204 Annual stress tests required. (a) General... conduct a stress test on or before March 31 of each calendar year based on financial data as of...

  3. 12 CFR 325.204 - Annual stress tests required.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 5 2014-01-01 2014-01-01 false Annual stress tests required. 325.204 Section... POLICY CAPITAL MAINTENANCE Annual Stress Test § 325.204 Annual stress tests required. (a) General... conduct a stress test on or before March 31 of each calendar year based on financial data as of...

  4. 45 CFR 149.325 - Requirements for eligibility of claims.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Section 149.325 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES REQUIREMENTS RELATING TO HEALTH CARE ACCESS REQUIREMENTS FOR THE EARLY RETIREE REINSURANCE PROGRAM Reimbursement Methods § 149.325... benefits for an early retiree, as defined in § 149.2, has been incurred during the applicable plan...

  5. 45 CFR 149.325 - Requirements for eligibility of claims.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Section 149.325 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES REQUIREMENTS RELATING TO HEALTH CARE ACCESS REQUIREMENTS FOR THE EARLY RETIREE REINSURANCE PROGRAM Reimbursement Methods § 149.325... benefits for an early retiree, as defined in § 149.2, has been incurred during the applicable plan...

  6. 45 CFR 149.325 - Requirements for eligibility of claims.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Section 149.325 Public Welfare Department of Health and Human Services REQUIREMENTS RELATING TO HEALTH CARE ACCESS REQUIREMENTS FOR THE EARLY RETIREE REINSURANCE PROGRAM Reimbursement Methods § 149.325... benefits for an early retiree, as defined in § 149.2, has been incurred during the applicable plan...

  7. 45 CFR 149.325 - Requirements for eligibility of claims.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Section 149.325 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES REQUIREMENTS RELATING TO HEALTH CARE ACCESS REQUIREMENTS FOR THE EARLY RETIREE REINSURANCE PROGRAM Reimbursement Methods § 149.325... benefits for an early retiree, as defined in § 149.2, has been incurred during the applicable plan...

  8. 33 CFR 117.325 - St. Johns River.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false St. Johns River. 117.325 Section... DRAWBRIDGE OPERATION REGULATIONS Specific Requirements Florida § 117.325 St. Johns River. (a) The drawspan..., displaying flashing green lights to indicate that vessels may pass. (3) When a train approaches, large...

  9. 33 CFR 117.325 - St. Johns River.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false St. Johns River. 117.325 Section... DRAWBRIDGE OPERATION REGULATIONS Specific Requirements Florida § 117.325 St. Johns River. (a) The drawspan..., displaying flashing green lights to indicate that vessels may pass. (3) When a train approaches, large...

  10. 33 CFR 117.325 - St. Johns River.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false St. Johns River. 117.325 Section... DRAWBRIDGE OPERATION REGULATIONS Specific Requirements Florida § 117.325 St. Johns River. (a) The drawspan..., displaying flashing green lights to indicate that vessels may pass. (3) When a train approaches, large...

  11. 33 CFR 117.325 - St. Johns River.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false St. Johns River. 117.325 Section... DRAWBRIDGE OPERATION REGULATIONS Specific Requirements Florida § 117.325 St. Johns River. (a) The drawspan..., displaying flashing green lights to indicate that vessels may pass. (3) When a train approaches, large...

  12. 33 CFR 117.325 - St. Johns River.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false St. Johns River. 117.325 Section... DRAWBRIDGE OPERATION REGULATIONS Specific Requirements Florida § 117.325 St. Johns River. (a) The drawspan..., displaying flashing green lights to indicate that vessels may pass. (3) When a train approaches, large...

  13. 46 CFR 154.325 - Accommodation, service, and control spaces.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 5 2013-10-01 2013-10-01 false Accommodation, service, and control spaces. 154.325... Equipment Ship Arrangements § 154.325 Accommodation, service, and control spaces. (a) Accommodation, service, and control spaces must be outside the cargo area. (b) If a hold space having a cargo...

  14. 49 CFR 325.7 - Allowable noise levels.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... is based on motor carrier noise emission requirements specified in 40 CFR 202.20 and 40 CFR 202.21. ... 49 Transportation 5 2014-10-01 2014-10-01 false Allowable noise levels. 325.7 Section 325.7... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION GENERAL REGULATIONS COMPLIANCE WITH INTERSTATE MOTOR CARRIER...

  15. 9 CFR 93.325 - Horses from Mexico.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Horses from Mexico. 93.325 Section 93... CONVEYANCE AND SHIPPING CONTAINERS Horses Mexico 18 § 93.325 Horses from Mexico. Horses offered for entry... § 93.324: Provided, That horses offered for importation from tick-infected areas of Mexico shall...

  16. 9 CFR 93.325 - Horses from Mexico.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 9 Animals and Animal Products 1 2011-01-01 2011-01-01 false Horses from Mexico. 93.325 Section 93... CONVEYANCE AND SHIPPING CONTAINERS Horses Mexico 18 § 93.325 Horses from Mexico. Horses offered for entry... § 93.324: Provided, That horses offered for importation from tick-infected areas of Mexico shall...

  17. 9 CFR 93.325 - Horses from Mexico.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 9 Animals and Animal Products 1 2012-01-01 2012-01-01 false Horses from Mexico. 93.325 Section 93... CONVEYANCE AND SHIPPING CONTAINERS Horses Mexico 18 § 93.325 Horses from Mexico. Horses offered for entry... § 93.324: Provided, That horses offered for importation from tick-infected areas of Mexico shall...

  18. 9 CFR 93.325 - Horses from Mexico.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 9 Animals and Animal Products 1 2013-01-01 2013-01-01 false Horses from Mexico. 93.325 Section 93... CONVEYANCE AND SHIPPING CONTAINERS Horses Mexico 18 § 93.325 Horses from Mexico. Horses offered for entry... § 93.324: Provided, That horses offered for importation from tick-infected areas of Mexico shall...

  19. 9 CFR 93.325 - Horses from Mexico.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 9 Animals and Animal Products 1 2014-01-01 2014-01-01 false Horses from Mexico. 93.325 Section 93... CONVEYANCE AND SHIPPING CONTAINERS Horses Mexico 18 § 93.325 Horses from Mexico. Horses offered for entry... § 93.324: Provided, That horses offered for importation from tick-infected areas of Mexico shall...

  20. 14 CFR 139.325 - Airport emergency plan.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airport emergency plan. 139.325 Section 139... AIRPORTS Operations § 139.325 Airport emergency plan. (a) In a manner authorized by the Administrator, each certificate holder must develop and maintain an airport emergency plan designed to minimize the...

  1. 46 CFR 154.325 - Accommodation, service, and control spaces.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 5 2011-10-01 2011-10-01 false Accommodation, service, and control spaces. 154.325... Equipment Ship Arrangements § 154.325 Accommodation, service, and control spaces. (a) Accommodation, service, and control spaces must be outside the cargo area. (b) If a hold space having a cargo...

  2. Laparoscopic paracolostomy hernia mesh repair.

    PubMed

    Virzí, Giuseppe; Giuseppe, Virzí; Scaravilli, Francesco; Francesco, Scaravilli; Ragazzi, Salvatore; Salvatore, Ragazzi; Piazza, Diego; Diego, Piazza

    2007-12-01

    Paracolostomy hernia is a common occurrence, representing a late complication of stoma surgery. Different surgical techniques have been proposed to repair the wall defect, but the lowest recurrence rates are associated with the use of mesh. We present the case report of a patient in which laparoscopic paracolostomy hernia mesh repair has been successfully performed. PMID:18097321

  3. Quadrilateral finite element mesh coarsening

    SciTech Connect

    Staten, Matthew L; Dewey, Mark W; Benzley, Steven E

    2012-10-16

    Techniques for coarsening a quadrilateral mesh are described. These techniques include identifying a coarsening region within the quadrilateral mesh to be coarsened. Quadrilateral elements along a path through the coarsening region are removed. Node pairs along opposite sides of the path are identified. The node pairs along the path are then merged to collapse the path.

  4. Adaptive and Unstructured Mesh Cleaving

    PubMed Central

    Bronson, Jonathan R.; Sastry, Shankar P.; Levine, Joshua A.; Whitaker, Ross T.

    2015-01-01

    We propose a new strategy for boundary conforming meshing that decouples the problem of building tetrahedra of proper size and shape from the problem of conforming to complex, non-manifold boundaries. This approach is motivated by the observation that while several methods exist for adaptive tetrahedral meshing, they typically have difficulty at geometric boundaries. The proposed strategy avoids this conflict by extracting the boundary conforming constraint into a secondary step. We first build a background mesh having a desired set of tetrahedral properties, and then use a generalized stenciling method to divide, or “cleave”, these elements to get a set of conforming tetrahedra, while limiting the impacts cleaving has on element quality. In developing this new framework, we make several technical contributions including a new method for building graded tetrahedral meshes as well as a generalization of the isosurface stuffing and lattice cleaving algorithms to unstructured background meshes. PMID:26137171

  5. Adaptive Skin Meshes Coarsening for Biomolecular Simulation.

    PubMed

    Shi, Xinwei; Koehl, Patrice

    2011-06-01

    In this paper, we present efficient algorithms for generating hierarchical molecular skin meshes with decreasing size and guaranteed quality. Our algorithms generate a sequence of coarse meshes for both the surfaces and the bounded volumes. Each coarser surface mesh is adaptive to the surface curvature and maintains the topology of the skin surface with guaranteed mesh quality. The corresponding tetrahedral mesh is conforming to the interface surface mesh and contains high quality tetrahedral that decompose both the interior of the molecule and the surrounding region (enclosed in a sphere). Our hierarchical tetrahedral meshes have a number of advantages that will facilitate fast and accurate multigrid PDE solvers. Firstly, the quality of both the surface triangulations and tetrahedral meshes is guaranteed. Secondly, the interface in the tetrahedral mesh is an accurate approximation of the molecular boundary. In particular, all the boundary points lie on the skin surface. Thirdly, our meshes are Delaunay meshes. Finally, the meshes are adaptive to the geometry. PMID:21779137

  6. Adaptive Skin Meshes Coarsening for Biomolecular Simulation

    PubMed Central

    Shi, Xinwei; Koehl, Patrice

    2011-01-01

    In this paper, we present efficient algorithms for generating hierarchical molecular skin meshes with decreasing size and guaranteed quality. Our algorithms generate a sequence of coarse meshes for both the surfaces and the bounded volumes. Each coarser surface mesh is adaptive to the surface curvature and maintains the topology of the skin surface with guaranteed mesh quality. The corresponding tetrahedral mesh is conforming to the interface surface mesh and contains high quality tetrahedral that decompose both the interior of the molecule and the surrounding region (enclosed in a sphere). Our hierarchical tetrahedral meshes have a number of advantages that will facilitate fast and accurate multigrid PDE solvers. Firstly, the quality of both the surface triangulations and tetrahedral meshes is guaranteed. Secondly, the interface in the tetrahedral mesh is an accurate approximation of the molecular boundary. In particular, all the boundary points lie on the skin surface. Thirdly, our meshes are Delaunay meshes. Finally, the meshes are adaptive to the geometry. PMID:21779137

  7. Streaming Compression of Hexahedral Meshes

    SciTech Connect

    Isenburg, M; Courbet, C

    2010-02-03

    We describe a method for streaming compression of hexahedral meshes. Given an interleaved stream of vertices and hexahedral our coder incrementally compresses the mesh in the presented order. Our coder is extremely memory efficient when the input stream documents when vertices are referenced for the last time (i.e. when it contains topological finalization tags). Our coder then continuously releases and reuses data structures that no longer contribute to compressing the remainder of the stream. This means in practice that our coder has only a small fraction of the whole mesh in memory at any time. We can therefore compress very large meshes - even meshes that do not file in memory. Compared to traditional, non-streaming approaches that load the entire mesh and globally reorder it during compression, our algorithm trades a less compact compressed representation for significant gains in speed, memory, and I/O efficiency. For example, on the 456k hexahedra 'blade' mesh, our coder is twice as fast and uses 88 times less memory (only 3.1 MB) with the compressed file increasing about 3% in size. We also present the first scheme for predictive compression of properties associated with hexahedral cells.

  8. 21 CFR 878.3300 - Surgical mesh.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... GENERAL AND PLASTIC SURGERY DEVICES Prosthetic Devices § 878.3300 Surgical mesh. (a) Identification... acetabular and cement restrictor mesh used during orthopedic surgery. (b) Classification. Class II....

  9. 21 CFR 878.3300 - Surgical mesh.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... GENERAL AND PLASTIC SURGERY DEVICES Prosthetic Devices § 878.3300 Surgical mesh. (a) Identification... acetabular and cement restrictor mesh used during orthopedic surgery. (b) Classification. Class II....

  10. 21 CFR 878.3300 - Surgical mesh.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... GENERAL AND PLASTIC SURGERY DEVICES Prosthetic Devices § 878.3300 Surgical mesh. (a) Identification... acetabular and cement restrictor mesh used during orthopedic surgery. (b) Classification. Class II....

  11. Nanowire mesh solar fuels generator

    DOEpatents

    Yang, Peidong; Chan, Candace; Sun, Jianwei; Liu, Bin

    2016-05-24

    This disclosure provides systems, methods, and apparatus related to a nanowire mesh solar fuels generator. In one aspect, a nanowire mesh solar fuels generator includes (1) a photoanode configured to perform water oxidation and (2) a photocathode configured to perform water reduction. The photocathode is in electrical contact with the photoanode. The photoanode may include a high surface area network of photoanode nanowires. The photocathode may include a high surface area network of photocathode nanowires. In some embodiments, the nanowire mesh solar fuels generator may include an ion conductive polymer infiltrating the photoanode and the photocathode in the region where the photocathode is in electrical contact with the photoanode.

  12. Augmentation mentoplasty using Mersilene mesh.

    PubMed

    McCollough, E G; Hom, D B; Weigel, M T; Anderson, J R

    1990-10-01

    Many different materials are available for augmentation mentoplasty. However, the optimal implant material for chin implantation has yet to be found. During the past several years, a number of experienced surgeons have turned to the use of Mersilene mesh. Mersilene mesh is a non-absorbable Dacron polyester fiber that can be conformed easily into layers to achieve tailored dimensions and shape. At the McCollough Plastic Surgery Clinic PA, Birmingham, Ala, 277 patients over a 10-year period underwent chin augmentation with Mersilene mesh implants. The material provides excellent tensile strength, durability, and surgical adaptability. The overall complication rate was 3.2% (nine patients); infection rate, 2.5% (seven patients); and removal secondary to infection, 1.7% (five patients). Based on this 10-year experience, Mersilene mesh remains our material of choice for chin augmentation. PMID:2206500

  13. Parallel Adaptive Mesh Refinement Library

    NASA Technical Reports Server (NTRS)

    Mac-Neice, Peter; Olson, Kevin

    2005-01-01

    Parallel Adaptive Mesh Refinement Library (PARAMESH) is a package of Fortran 90 subroutines designed to provide a computer programmer with an easy route to extension of (1) a previously written serial code that uses a logically Cartesian structured mesh into (2) a parallel code with adaptive mesh refinement (AMR). Alternatively, in its simplest use, and with minimal effort, PARAMESH can operate as a domain-decomposition tool for users who want to parallelize their serial codes but who do not wish to utilize adaptivity. The package builds a hierarchy of sub-grids to cover the computational domain of a given application program, with spatial resolution varying to satisfy the demands of the application. The sub-grid blocks form the nodes of a tree data structure (a quad-tree in two or an oct-tree in three dimensions). Each grid block has a logically Cartesian mesh. The package supports one-, two- and three-dimensional models.

  14. Gradient scaling for nonuniform meshes

    SciTech Connect

    Margolin, L.G.; Ruppel, H.M.; Demuth, R.B.

    1985-01-01

    This paper is concerned with the effect of nonuniform meshes on the accuracy of finite-difference calculations of fluid flow. In particular, when a simple shock propagates through a nonuniform mesh, one may fail to model the jump conditions across the shock even when the equations are differenced in manifestly conservative fashion. We develop an approximate dispersion analysis of the numerical equations and identify the source of the mesh dependency with the form of the artificial viscosity. We then derive an algebraic correction to the numerical equations - a scaling factor for the pressure gradient - to essentially eliminate the mesh dependency. We present several calculations to illustrate our theory. We conclude with an alternate interpretation of our results. 14 refs., 5 figs.

  15. Mersiline mesh in premaxillary augmentation.

    PubMed

    Foda, Hossam M T

    2005-01-01

    Premaxillary retrusion may distort the aesthetic appearance of the columella, lip, and nasal tip. This defect is characteristically seen in, but not limited to, patients with cleft lip nasal deformity. This study investigated 60 patients presenting with premaxillary deficiencies in which Mersiline mesh was used to augment the premaxilla. All the cases had surgery using the external rhinoplasty technique. Two methods of augmentation with Mersiline mesh were used: the Mersiline roll technique, for the cases with central symmetric deficiencies, and the Mersiline packing technique, for the cases with asymmetric deficiencies. Premaxillary augmentation with Mersiline mesh proved to be simple technically, easy to perform, and not associated with any complications. Periodic follow-up evaluation for a mean period of 32 months (range, 12-98 months) showed that an adequate degree of premaxillary augmentation was maintained with no clinically detectable resorption of the mesh implant. PMID:15959688

  16. Unstructured mesh methods for CFD

    NASA Technical Reports Server (NTRS)

    Peraire, J.; Morgan, K.; Peiro, J.

    1990-01-01

    Mesh generation methods for Computational Fluid Dynamics (CFD) are outlined. Geometric modeling is discussed. An advancing front method is described. Flow past a two engine Falcon aeroplane is studied. An algorithm and associated data structure called the alternating digital tree, which efficiently solves the geometric searching problem is described. The computation of an initial approximation to the steady state solution of a given poblem is described. Mesh generation for transient flows is described.

  17. Unstructured mesh methods for CFD

    NASA Astrophysics Data System (ADS)

    Peraire, J.; Morgan, K.; Peiro, J.

    Mesh generation methods for Computational Fluid Dynamics (CFD) are outlined. Geometric modeling is discussed. An advancing front method is described. Flow past a two engine Falcon aeroplane is studied. An algorithm and associated data structure called the alternating digital tree, which efficiently solves the geometric searching problem is described. The computation of an initial approximation to the steady state solution of a given poblem is described. Mesh generation for transient flows is described.

  18. Image-driven mesh optimization

    SciTech Connect

    Lindstrom, P; Turk, G

    2001-01-05

    We describe a method of improving the appearance of a low vertex count mesh in a manner that is guided by rendered images of the original, detailed mesh. This approach is motivated by the fact that greedy simplification methods often yield meshes that are poorer than what can be represented with a given number of vertices. Our approach relies on edge swaps and vertex teleports to alter the mesh connectivity, and uses the downhill simplex method to simultaneously improve vertex positions and surface attributes. Note that this is not a simplification method--the vertex count remains the same throughout the optimization. At all stages of the optimization the changes are guided by a metric that measures the differences between rendered versions of the original model and the low vertex count mesh. This method creates meshes that are geometrically faithful to the original model. Moreover, the method takes into account more subtle aspects of a model such as surface shading or whether cracks are visible between two interpenetrating parts of the model.

  19. 4. INTERIOR OF FIRSTFLOOR MAIN SECTION OF BUILDING 325. VIEW ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. INTERIOR OF FIRST-FLOOR MAIN SECTION OF BUILDING 325. VIEW TO EAST. - Rocky Mountain Arsenal, Electric Power Plant, 1022 feet South of December Seventh Avenue; 280 feet West of D Street, Commerce City, Adams County, CO

  20. 5. INTERIOR OF SECONDFLOOR MAIN SECTION OF BUILDING 325. VIEW ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    5. INTERIOR OF SECOND-FLOOR MAIN SECTION OF BUILDING 325. VIEW TO EAST. - Rocky Mountain Arsenal, Electric Power Plant, 1022 feet South of December Seventh Avenue; 280 feet West of D Street, Commerce City, Adams County, CO

  1. 49 CFR 325.33 - Site characteristics; highway operations.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... concrete barriers (see § 325.5(c)(4)). (4) One or more curbs having a vertical height of 1 foot (.3 m) or... of the highway within the test site must be dry, paved with relatively smooth concrete or...

  2. 49 CFR 325.33 - Site characteristics; highway operations.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... concrete barriers (see § 325.5(c)(4)). (4) One or more curbs having a vertical height of 1 foot (.3 m) or... of the highway within the test site must be dry, paved with relatively smooth concrete or...

  3. 49 CFR 325.33 - Site characteristics; highway operations.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... concrete barriers (see § 325.5(c)(4)). (4) One or more curbs having a vertical height of 1 foot (.3 m) or... of the highway within the test site must be dry, paved with relatively smooth concrete or...

  4. 49 CFR 325.59 - Measurement procedure; stationary test.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Stationary Test, 40 CFR 202.21. (Table 1 in § 325.7 lists the range of maximum permissible sound level..., asphalt spreaders, liquid or slurry pumps, auxiliary air compressors, welders, and trash compactors....

  5. Method and system for mesh network embedded devices

    NASA Technical Reports Server (NTRS)

    Wang, Ray (Inventor)

    2009-01-01

    A method and system for managing mesh network devices. A mesh network device with integrated features creates an N-way mesh network with a full mesh network topology or a partial mesh network topology.

  6. User Manual for the PROTEUS Mesh Tools

    SciTech Connect

    Smith, Micheal A.; Shemon, Emily R.

    2015-06-01

    This report describes the various mesh tools that are provided with the PROTEUS code giving both descriptions of the input and output. In many cases the examples are provided with a regression test of the mesh tools. The most important mesh tools for any user to consider using are the MT_MeshToMesh.x and the MT_RadialLattice.x codes. The former allows the conversion between most mesh types handled by PROTEUS while the second allows the merging of multiple (assembly) meshes into a radial structured grid. Note that the mesh generation process is recursive in nature and that each input specific for a given mesh tool (such as .axial or .merge) can be used as “mesh” input for any of the mesh tools discussed in this manual.

  7. H-Coal Pilot Plant: coal-preparation test. Technical report No. T-5

    SciTech Connect

    McCoy, D.C.; Smith, E.R.

    1980-07-15

    Initial commissioning and test results for the coal-pulverizing-and-drying system in Section 100 are reported. The results obtained in calibrating the weigh feeder which feeds the prepared coal to the Slurry Mix Tank, Q-236, are also given. Coal was first fed to the pulverizing system on April 14 for approximately thirty minutes. On May 2, the pulverizing system was successfully operated for six hours with the bowl mill coal feed rate purposefully varied between 50 and 100% of full load. The system was then voluntarily shut down. These and subsequent operations have demonstrated that: (1) the bowl mill can be operated at coal feed rates of 20 to 40 tons/h, (2) that a 7.6 weight percent moisture coal feed stock can be easily dried to 2.0 weight percent moisture, and (3) that the bowl mill can be adjusted to routinely produce a 90 to 98 weight percent - 100 mesh product (95% - 100 mesh average) with 72 to 89 weight percent passing 200 mesh (80% - 200 mesh average). During the start-up operations, special tests were conducted to determine the heat losses from the pulverizing system. The results indicate that the average system heat loss is 2,850,000 Btu/h and that the thermal efficiency, defined as the number of Btus required to heat and dry the coal divided by the number of Btus supplied by the fuel, is about 81%. The coal grinding tests also demonstrated that even at the relatively low temperatures (200 to 300/sup 0/F) that were maintained in the pulverizing system the fine coal dust produced readily reacts with the low amount of oxygen in the dryer flue gases. The prepared coal weigh feeder was calibrated for a range of 5 to 12.5 tons/h.

  8. The Lagrange-mesh method

    NASA Astrophysics Data System (ADS)

    Baye, Daniel

    2015-03-01

    The Lagrange-mesh method is an approximate variational method taking the form of equations on a grid thanks to the use of a Gauss-quadrature approximation. The variational basis related to this Gauss quadrature is composed of Lagrange functions which are infinitely differentiable functions vanishing at all mesh points but one. This method is quite simple to use and, more importantly, can be very accurate with small number of mesh points for a number of problems. The accuracy may however be destroyed by singularities of the potential term. This difficulty can often be overcome by a regularization of the Lagrange functions which does not affect the simplicity and accuracy of the method. The principles of the Lagrange-mesh method are described, as well as various generalizations of the Lagrange functions and their regularization. The main existing meshes are reviewed and extensive formulas are provided which make the numerical calculations simple. They are in general based on classical orthogonal polynomials. The extensions to non-classical orthogonal polynomials and periodic functions are also presented. Applications start with the calculations of energies, wave functions and some observables for bound states in simple solvable models which can rather easily be used as exercises by the reader. The Dirac equation is also considered. Various problems in the continuum can also simply and accurately be solved with the Lagrange-mesh technique including multichannel scattering or scattering by non-local potentials. The method can be applied to three-body systems in appropriate systems of coordinates. Simple atomic, molecular and nuclear systems are taken as examples. The applications to the time-dependent Schrödinger equation, to the Gross-Pitaevskii equation and to Hartree-Fock calculations are also discussed as well as translations and rotations on a Lagrange mesh.

  9. Single port laparoscopic mesh rectopexy

    PubMed Central

    2016-01-01

    Introduction Traditionally, laparoscopic mesh rectopexy is performed with four ports, in an attempt to improve cosmetic results. Following laparoscopic mesh rectopexy there is a new operative technique called single-port laparoscopic mesh rectopexy. Aim To evaluate the single-port laparoscopic mesh rectopexy technique in control of rectal prolapse and the cosmesis and body image issues of this technique. Material and methods The study was conducted in El Fayoum University Hospital between July 2013 and November 2014 in elective surgery for symptomatic rectal prolapse with single-port laparoscopic mesh rectopexy on 10 patients. Results The study included 10 patients: 3 (30%) males and 7 (70%) females. Their ages ranged between 19 years and 60 years (mean: 40.3 ±6 years), and they all underwent laparoscopic mesh rectopexy. There were no conversions to open technique, nor injuries to the rectum or bowel, and there were no mortalities. Mean operative time was 120 min (range: 90–150 min), and mean hospital stay was 2 days (range: 1–3 days). Preoperatively, incontinence was seen in 5 (50%) patients and constipation in 4 (40%). Postoperatively, improvement in these symptoms was seen in 3 (60%) patients for incontinence and in 3 (75%) for constipation. Follow-up was done for 6 months and no recurrence was found with better cosmetic appearance for all patients. Conclusions Single-port laparoscopic mesh rectopexy is a safe procedure with good results as regards operative time, improvement in bowel function, morbidity, cost, and recurrence, and with better cosmetic appearance. PMID:27350840

  10. A novel concept for high conversion of coal to liquids. Final report, 1 September 1988--31 August 1992

    SciTech Connect

    Wiser, W.H.; Shabtai, J.

    1994-04-01

    A batch microreactor was designed and fabricated as a means of investigating maximum yields of liquids obtainable in very short reaction times of the order of a few seconds, and the maximum ratios of liquids/hydrocarbon (HC) gases obtainable under those conditions. A Wyodak sub-bituminous coal, crushed and sieved to {minus}200 mesh particle size, was used in the experiments, with a temperature of 500{degrees}C and a pressure of 1500 psi. The fine coal particles were fed dry to the reactor and heated to reaction temperature in times of one to two seconds. At a time of 3 seconds at reaction temperature, in a single pass a liquid yield of 60% by weight of the coal was obtained, accompanied by a ratio of liquids/(HC) gases of 30/1. When the unreacted solids were recycled to the reactor, and the results combined with those of the first pass, a liquid yield of 82% by weight of the coal was achieved, accompanied by a ratio of liquids/HC gases of 30/1. This ratio represents only about 3 wt percent HC gases, much lower that is produced in current advanced technologies, and represents a large saving in hydrogen consumption. A simulated distillation technique was applied to the liquids. The liquid product contained 86% by weight (of the liquids) total distillables (boiling point below 538{degrees}C), including 70% by weight of low-boiling fractions in the gasoline, kerosene and gas oil range (boiling point up to 325{degrees}C). The liquid product exhibited a H/C ratio of 1.5, which is considerably higher than observed in current advanced technologies for the primary liquids. Several catalysts were investigated. Iron catalysts, specifically ferric chloride hexahydrate and ferric sulfate pentahydrate, each produced these high conversions and high ratios of liquids/HC gases.

  11. Improvements to the Unstructured Mesh Generator MESH3D

    NASA Technical Reports Server (NTRS)

    Thomas, Scott D.; Baker, Timothy J.; Cliff, Susan E.

    1999-01-01

    The AIRPLANE process starts with an aircraft geometry stored in a CAD system. The surface is modeled with a mesh of triangles and then the flow solver produces pressures at surface points which may be integrated to find forces and moments. The biggest advantage is that the grid generation bottleneck of the CFD process is eliminated when an unstructured tetrahedral mesh is used. MESH3D is the key to turning around the first analysis of a CAD geometry in days instead of weeks. The flow solver part of AIRPLANE has proven to be robust and accurate over a decade of use at NASA. It has been extensively validated with experimental data and compares well with other Euler flow solvers. AIRPLANE has been applied to all the HSR geometries treated at Ames over the course of the HSR program in order to verify the accuracy of other flow solvers. The unstructured approach makes handling complete and complex geometries very simple because only the surface of the aircraft needs to be discretized, i.e. covered with triangles. The volume mesh is created automatically by MESH3D. AIRPLANE runs well on multiple platforms. Vectorization on the Cray Y-MP is reasonable for a code that uses indirect addressing. Massively parallel computers such as the IBM SP2, SGI Origin 2000, and the Cray T3E have been used with an MPI version of the flow solver and the code scales very well on these systems. AIRPLANE can run on a desktop computer as well. AIRPLANE has a future. The unstructured technologies developed as part of the HSR program are now targeting high Reynolds number viscous flow simulation. The pacing item in this effort is Navier-Stokes mesh generation.

  12. Dewatering of fine coal using hyperbaric filter

    SciTech Connect

    Yang, J.; Wang, X.H.; Parekh, B.K.

    1995-12-31

    Removal of moisture from ultra-fine clean coal (minus 100 mesh) to below 20% level is difficult using conventional dewatering equipment. This paper describes a couple of dewatering approaches which were found to be effective in providing filter cakes containing less than 20% moisture. These approaches involve addition of metal ion-surfactant, and split size dewatering of coal without addition of any reagent.

  13. Cache-oblivious mesh layouts

    SciTech Connect

    Yoon, Sung-Eui; Lindstrom, Peter; Pascucci, Valerio; Manocha, Dinesh

    2005-07-01

    We present a novel method for computing cache-oblivious layouts of large meshes that improve the performance of interactive visualization and geometric processing algorithms. Given that the mesh is accessed in a reasonably coherent manner, we assume no particular data access patterns or cache parameters of the memory hierarchy involved in the computation. Furthermore, our formulation extends directly to computing layouts of multi-resolution and bounding volume hierarchies of large meshes. We develop a simple and practical cache-oblivious metric for estimating cache misses. Computing a coherent mesh layout is reduced to a combinatorial optimization problem. We designed and implemented an out-of-core multilevel minimization algorithm and tested its performance on unstructured meshes composed of tens to hundreds of millions of triangles. Our layouts can significantly reduce the number of cache misses. We have observed 2-20 times speedups in view-dependent rendering, collision detection, and isocontour extraction without any modification of the algorithms or runtime applications.

  14. Self-Organizing Mesh Generation

    1991-11-01

    A set of five programs which make up a self organizing mesh generation package. QMESH generates meshes having quadrilateral elements on arbitrarily shaped two-dimensional (planar or axisymmetric) bodies. It is designed for use with two-dimensional finite element analysis applications. A flexible hierarchal input scheme is used to describe bodies to QMESH as collections of regions. A mesh for each region is developed independently, with the final assembly and bandwidth minimization performed by the independent program,more » RENUM or RENUM8. RENUM is applied when four-node elements are desired. Eight node elements (with mid side nodes) may be obtained with RENUM8. QPLOT and QPLOT8 are plot programs for meshes generated by the QMESH/RENUM and QMESH/RENUM8 program pairs respectively. QPLOT and QPLOT8 automatically section the mesh into appropriately-sized sections for legible display of node and element numbers, An overall plot showing the position of the selected plot areas is produced.« less

  15. Modified approaches for high pressure filtration of fine clean coal

    SciTech Connect

    Yang, J.; Groppo, J.G.; Parekh, B.K.

    1995-12-31

    Removal of moisture from fine (minus 28 mesh) clean coal to 20% or lower level is difficult using the conventional vacuum dewatering technique. High pressure filtration technique provides an avenue for obtaining low moisture in fine clean coal. This paper describes a couple of novel approaches for dewatering of fine clean coal using pressure filtration which provides much lower moisture in fine clean coal than that obtained using conventional pressure filter. The approaches involve (a) split stream dewatering and (b) addition of paper pulp to the coal slurry. For Pittsburgh No. 8 coal slurry, split stream dewatering at 400 mesh provided filter cake containing 12.9% moisture compared to 24.9% obtained on the feed material. The addition of paper pulp to the slurry provided filter cake containing about 17% moisture.

  16. Parallel automated adaptive procedures for unstructured meshes

    NASA Technical Reports Server (NTRS)

    Shephard, M. S.; Flaherty, J. E.; Decougny, H. L.; Ozturan, C.; Bottasso, C. L.; Beall, M. W.

    1995-01-01

    Consideration is given to the techniques required to support adaptive analysis of automatically generated unstructured meshes on distributed memory MIMD parallel computers. The key areas of new development are focused on the support of effective parallel computations when the structure of the numerical discretization, the mesh, is evolving, and in fact constructed, during the computation. All the procedures presented operate in parallel on already distributed mesh information. Starting from a mesh definition in terms of a topological hierarchy, techniques to support the distribution, redistribution and communication among the mesh entities over the processors is given, and algorithms to dynamically balance processor workload based on the migration of mesh entities are given. A procedure to automatically generate meshes in parallel, starting from CAD geometric models, is given. Parallel procedures to enrich the mesh through local mesh modifications are also given. Finally, the combination of these techniques to produce a parallel automated finite element analysis procedure for rotorcraft aerodynamics calculations is discussed and demonstrated.

  17. Issues in adaptive mesh refinement

    SciTech Connect

    Dai, William Wenlong

    2009-01-01

    In this paper, we present an approach for a patch-based adaptive mesh refinement (AMR) for multi-physics simulations. The approach consists of clustering, symmetry preserving, mesh continuity, flux correction, communications, and management of patches. Among the special features of this patch-based AMR are symmetry preserving, efficiency of refinement, special implementation offlux correction, and patch management in parallel computing environments. Here, higher efficiency of refinement means less unnecessarily refined cells for a given set of cells to be refined. To demonstrate the capability of the AMR framework, hydrodynamics simulations with many levels of refinement are shown in both two- and three-dimensions.

  18. Coal Research

    NASA Technical Reports Server (NTRS)

    1986-01-01

    Coal slurries are "clean" pulverized coal mixed with oil or water. Significant fuel savings can be realized when using coal slurries. Advanced Fuels Technology (AFT) utilized a COSMIC program, (Calculation of Complex Chemical Equilibrium Compositions), which provides specific capabilities for determining combustion products. The company has developed a cleaning process that removes much of the mineral sulphur and ash from the coals.

  19. Gaseous phase coal surface modification

    SciTech Connect

    Okoh, J.M.; Pinion, J.; Thiensatit, S.

    1992-05-07

    In this report, we present an improved, feasible and potentially cost effective method of cleaning and beneficiating ultrafine coal. Increased mechanization of mining methods and the need towards depyritization, and demineralization have led to an increase in the quantity of coal fines generated in recent times. For example, the amount of {minus}100 mesh coal occurring in coal preparation plant feeds now typically varies from 5 to 25% of the total feed. Environmental constraints coupled with the greatly increased cost of coal have made it increasingly important to recover more of these fines. Our method chemically modifies the surface of such coals by a series of gaseous phase treatments employing Friedel-Crafts reactions. By using olefins (ethene, propene and butene) and hydrogen chloride catalyst at elevated temperature, the surface hydrophobicity of coal is enhanced. This increased hydrophobicity is manifest in surface phenomena which reflect conditions at the solid/liquid interphase (zeta potential) and those which reflect conditions at the solid/liquid/gas interphases (contact angle, wettability and floatability).

  20. Reinforced rubber composition containing ground coal

    SciTech Connect

    Sperley, R.J.

    1984-10-16

    A reinforced rubber composition is provided comprising a mixture of (a) a sulfur vulcanizable rubber and (b) ground coal having an average mesh size of 25 or more and which produces an aqueous slurry with a pH of less than 7.0, and wherein a metallic reinforcing member is embedded in the rubber mixture of (a) and (b).

  1. Hybrid mesh for nasal airflow studies.

    PubMed

    Zubair, Mohammed; Abdullah, Mohammed Zulkifly; Ahmad, Kamarul Arifin

    2013-01-01

    The accuracy of the numerical result is closely related to mesh density as well as its distribution. Mesh plays a very significant role in the outcome of numerical simulation. Many nasal airflow studies have employed unstructured mesh and more recently hybrid mesh scheme has been utilized considering the complexity of anatomical architecture. The objective of this study is to compare the results of hybrid mesh with unstructured mesh and study its effect on the flow parameters inside the nasal cavity. A three-dimensional nasal cavity model is reconstructed based on computed tomographic images of a healthy Malaysian adult nose. Navier-Stokes equation for steady airflow is solved numerically to examine inspiratory nasal flow. The pressure drop obtained using the unstructured computational grid is about 22.6 Pa for a flow rate of 20 L/min, whereas the hybrid mesh resulted in 17.8 Pa for the same flow rate. The maximum velocity obtained at the nasal valve using unstructured grid is 4.18 m/s and that with hybrid mesh is around 4.76 m/s. Hybrid mesh reported lower grid convergence index (GCI) than the unstructured mesh. Significant differences between unstructured mesh and hybrid mesh are determined highlighting the usefulness of hybrid mesh for nasal airflow studies. PMID:23983811

  2. Hybrid Mesh for Nasal Airflow Studies

    PubMed Central

    Zubair, Mohammed; Abdullah, Mohammed Zulkifly; Ahmad, Kamarul Arifin

    2013-01-01

    The accuracy of the numerical result is closely related to mesh density as well as its distribution. Mesh plays a very significant role in the outcome of numerical simulation. Many nasal airflow studies have employed unstructured mesh and more recently hybrid mesh scheme has been utilized considering the complexity of anatomical architecture. The objective of this study is to compare the results of hybrid mesh with unstructured mesh and study its effect on the flow parameters inside the nasal cavity. A three-dimensional nasal cavity model is reconstructed based on computed tomographic images of a healthy Malaysian adult nose. Navier-Stokes equation for steady airflow is solved numerically to examine inspiratory nasal flow. The pressure drop obtained using the unstructured computational grid is about 22.6 Pa for a flow rate of 20 L/min, whereas the hybrid mesh resulted in 17.8 Pa for the same flow rate. The maximum velocity obtained at the nasal valve using unstructured grid is 4.18 m/s and that with hybrid mesh is around 4.76 m/s. Hybrid mesh reported lower grid convergence index (GCI) than the unstructured mesh. Significant differences between unstructured mesh and hybrid mesh are determined highlighting the usefulness of hybrid mesh for nasal airflow studies. PMID:23983811

  3. Mesh Size Control of Friction

    NASA Astrophysics Data System (ADS)

    Pitenis, Angela; Uruena, Juan Manuel; Schulze, Kyle D.; Cooper, Andrew C.; Angelini, Thomas E.; Sawyer, W. Gregory

    Soft, permeable sliding interfaces in aqueous environments are ubiquitous in nature but their ability to maintain high lubricity in a poor lubricant (water) has not been well understood. Hydrogels are excellent materials for fundamental soft matter and biotribology studies due to their high water content. While mesh size controls the material and transport properties of a hydrogel, its effects on friction were only recently explored. Polyacrylamide hydrogels slid in a Gemini (self-mated) interface produced low friction under low speeds, low pressures, macroscopic contact areas, and room temperature aqueous environments. The friction coefficients at these interfaces are lowest at low speeds and are speed-independent. This behavior is due to thermal fluctuations at the interface separating the surfaces, with water shearing in this region being the main source of dissipation. We found that mesh size had an inverse correlation with friction. We further investigated a transition from this behavior at higher speeds, and found that the transition speed correlated with the mesh size and relaxation time of the polymer network. Very soft and correspondingly large mesh size Gemini hydrogels show superlubricity under specific conditions with friction being less than 0.005.

  4. Multigrid for refined triangle meshes

    SciTech Connect

    Shapira, Yair

    1997-02-01

    A two-level preconditioning method for the solution of (locally) refined finite element schemes using triangle meshes is introduced. In the isotropic SPD case, it is shown that the condition number of the preconditioned stiffness matrix is bounded uniformly for all sufficiently regular triangulations. This is also verified numerically for an isotropic diffusion problem with highly discontinuous coefficients.

  5. Coal combustion by wet oxidation

    SciTech Connect

    Bettinger, J.A.; Lamparter, R.A.; McDowell, D.C.

    1980-11-15

    The combustion of coal by wet oxidation was studied by the Center for Waste Management Programs, of Michigan Technological University. In wet oxidation a combustible material, such as coal, is reacted with oxygen in the presence of liquid water. The reaction is typically carried out in the range of 204/sup 0/C (400/sup 0/F) to 353/sup 0/C (650/sup 0/F) with sufficient pressure to maintain the water present in the liquid state, and provide the partial pressure of oxygen in the gas phase necessary to carry out the reaction. Experimental studies to explore the key reaction parameters of temperature, time, oxidant, catalyst, coal type, and mesh size were conducted by running batch tests in a one-gallon stirred autoclave. The factors exhibiting the greatest effect on the extent of reaction were temperature and residence time. The effect of temperature was studied from 204/sup 0/C (400/sup 0/F) to 260/sup 0/C (500/sup 0/F) with a residence time from 600 to 3600 seconds. From this data, the reaction activation energy of 2.7 x 10/sup 4/ calories per mole was determined for a high-volatile-A-Bituminous type coal. The reaction rate constant may be determined at any temperature from the activation energy using the Arrhenius equation. Additional data were generated on the effect of mesh size and different coal types. A sample of peat was also tested. Two catalysts were evaluated, and their effects on reaction rate presented in the report. In addition to the high temperature combustion, low temperature desulfurization is discussed. Desulfurization can improve low grade coal to be used in conventional combustion methods. It was found that 90% of the sulfur can be removed from the coal by wet oxidation with the carbon untouched. Further desulfurization studies are indicated.

  6. Atomic Mass and Nuclear Binding Energy for Uut-325 (Ununtrium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Uut-325 (Ununtrium, atomic number Z = 113, mass number A = 325).

  7. Atomic Mass and Nuclear Binding Energy for Sg-325 (Seaborgium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Sg-325 (Seaborgium, atomic number Z = 106, mass number A = 325).

  8. Atomic Mass and Nuclear Binding Energy for Bh-325 (Bohrium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Bh-325 (Bohrium, atomic number Z = 107, mass number A = 325).

  9. Atomic Mass and Nuclear Binding Energy for Mt-325 (Meitnerium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Mt-325 (Meitnerium, atomic number Z = 109, mass number A = 325).

  10. Atomic Mass and Nuclear Binding Energy for Es-325 (Einsteinium)

    NASA Astrophysics Data System (ADS)

    Sukhoruchkin, S. I.; Soroko, Z. N.

    This document is part of the Supplement containing the complete sets of data of Subvolume B `Nuclei with Z = 55 - 100' of Volume 22 `Nuclear Binding Energies and Atomic Masses' of Landolt-Börnstein - Group I `Elementary Particles, Nuclei and Atoms', and additionally including data for nuclei with Z = 101 - 130. It provides atomic mass, mass excess, nuclear binding energy, nucleon separation energies, Q-values, and nucleon residual interaction parameters for atomic nuclei of the isotope Es-325 (Einsteinium, atomic number Z = 99, mass number A = 325).

  11. Optimizing the geometrical accuracy of curvilinear meshes

    NASA Astrophysics Data System (ADS)

    Toulorge, Thomas; Lambrechts, Jonathan; Remacle, Jean-François

    2016-04-01

    This paper presents a method to generate valid high order meshes with optimized geometrical accuracy. The high order meshing procedure starts with a linear mesh, that is subsequently curved without taking care of the validity of the high order elements. An optimization procedure is then used to both untangle invalid elements and optimize the geometrical accuracy of the mesh. Standard measures of the distance between curves are considered to evaluate the geometrical accuracy in planar two-dimensional meshes, but they prove computationally too costly for optimization purposes. A fast estimate of the geometrical accuracy, based on Taylor expansions of the curves, is introduced. An unconstrained optimization procedure based on this estimate is shown to yield significant improvements in the geometrical accuracy of high order meshes, as measured by the standard Hausdorff distance between the geometrical model and the mesh. Several examples illustrate the beneficial impact of this method on CFD solutions, with a particular role of the enhanced mesh boundary smoothness.

  12. Application of Quaternions for Mesh Deformation

    NASA Technical Reports Server (NTRS)

    Samareh, Jamshid A.

    2002-01-01

    A new three-dimensional mesh deformation algorithm, based on quaternion algebra, is introduced. A brief overview of quaternion algebra is provided, along with some preliminary results for two-dimensional structured and unstructured viscous mesh deformation.

  13. Underground Coal Thermal Treatment: Task 6 Topical Report, Utah Clean Coal Program

    SciTech Connect

    Smith, P.J.; Deo, M.; Edding, E.G.; Hradisky, M.; Kelly, K.E.; Krumm, R.; Sarofim, Adel; Wang, D.

    2014-08-15

    The long-term objective of this task is to develop a transformational energy production technology by in- situ thermal treatment of a coal seam for the production of substitute natural gas and/or liquid transportation fuels while leaving much of the coal’s carbon in the ground. This process converts coal to a high-efficiency, low-greenhouse gas (GHG) emitting fuel. It holds the potential of providing environmentally acceptable access to previously unusable coal resources. This task focused on three areas: Experimental. The Underground Coal Thermal Treatment (UCTT) team focused on experiments at two scales, bench-top and slightly larger, to develop data to understand the feasibility of a UCTT process as well as to develop validation/uncertainty quantification (V/UQ) data for the simulation team. Simulation. The investigators completed development of High Performance Computing (HPC) simulations of UCTT. This built on our simulation developments over the course of the task and included the application of Computational Fluid Dynamics (CFD)- based tools to perform HPC simulations of a realistically sized domain representative of an actual coal field located in Utah. CO2 storage. In order to help determine the amount of CO2 that can be sequestered in a coal formation that has undergone UCTT, adsorption isotherms were performed on coals treated to 325, 450, and 600°C with slow heating rates. Raw material was sourced from the Sufco (Utah), Carlinville (Illinois), and North Antelope (Wyoming) mines. The study indicated that adsorptive capacity for the coals increased with treatment temperature and that coals treated to 325°C showed less or similar capacity to the untreated coals.

  14. 6th International Meshing Roundtable '97

    SciTech Connect

    White, D.

    1997-09-01

    The goal of the 6th International Meshing Roundtable is to bring together researchers and developers from industry, academia, and government labs in a stimulating, open environment for the exchange of technical information related to the meshing process. In the pas~ the Roundtable has enjoyed significant participation born each of these groups from a wide variety of countries. The Roundtable will consist of technical presentations from contributed papers and abstracts, two invited speakers, and two invited panels of experts discussing topics related to the development and use of automatic mesh generation tools. In addition, this year we will feature a "Bring Your Best Mesh" competition and poster session to encourage discussion and participation from a wide variety of mesh generation tool users. The schedule and evening social events are designed to provide numerous opportunities for informal dialog. A proceedings will be published by Sandia National Laboratories and distributed at the Roundtable. In addition, papers of exceptionally high quaIity will be submitted to a special issue of the International Journal of Computational Geometry and Applications. Papers and one page abstracts were sought that present original results on the meshing process. Potential topics include but are got limited to: Unstructured triangular and tetrahedral mesh generation Unstructured quadrilateral and hexahedral mesh generation Automated blocking and structured mesh generation Mixed element meshing Surface mesh generation Geometry decomposition and clean-up techniques Geometry modification techniques related to meshing Adaptive mesh refinement and mesh quality control Mesh visualization Special purpose meshing algorithms for particular applications Theoretical or novel ideas with practical potential Technical presentations from industrial researchers.

  15. Conservation properties of unstructured staggered mesh schemes

    SciTech Connect

    Perot, B.

    2000-03-20

    Classic Cartesian staggered mesh schemes have a number of attractive properties. They do not display spurious pressure modes and they have been shown to locally conserve, mass, momentum, kinetic energy, and circulation to machine precision. Recently, a number of generalizations of the staggered mesh approach have been proposed for unstructured (triangular or tetrahedral) meshes. These unstructured staggered mesh methods have been created to retain the attractive pressure aspects and mass conservation properties of the classic Cartesian mesh method. This work addresses the momentum, kinetic energy, and circulation conservation properties of unstructured staggered mesh methods. It is shown that with certain choices of the velocity interpolation, unstructured staggered mesh discretization of the divergence form of the Navier-Stokes equations can conserve kinetic energy and momentum both locally and globally. In addition, it is shown that unstructured staggered mesh discretization of the rotational form of the Navier-Stokes equations can conserve kinetic energy and circulation both locally and globally. The analysis includes viscous terms and a generalization of the concept of conservation in the presence of viscosity to include a negative definite dissipation term in the kinetic energy equation. These novel conserving unstructured staggered mesh schemes have not been previously analyzed. It is shown that they are first-order accurate on nonuniform two-dimensional unstructured meshes and second-order accurate on uniform unstructured meshes. Numerical confirmation of the conservation properties and the order of accuracy of these unstructured staggered mesh methods is presented.

  16. Hybrid mesh generation using advancing reduction technique

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This study presents an extension of the application of the advancing reduction technique to the hybrid mesh generation. The proposed algorithm is based on a pre-generated rectangle mesh (RM) with a certain orientation. The intersection points between the two sets of perpendicular mesh lines in RM an...

  17. Computing The Compliances Of Gear Meshes

    NASA Technical Reports Server (NTRS)

    Lewicki, D. G.; Savage, M.; Caldwell, R. J.; Wisor, G. D.

    1988-01-01

    Computer model simulates compliance and sharing of loads in spur-gear mesh. Use of solid-body analysis as lower bound and rim analysis as upper bound for mesh compliance, reasonable approximations obtained for compliance in spur-gear mesh.

  18. Reducing the moisture content of clean coals

    SciTech Connect

    Raleigh, C.E. )

    1992-11-01

    Volume four contains the results of an Empire State Electric Energy Research corporation and Electric Power Research Institute (EPRI) funded investigation to evaluate the effects and economics of applying ultrasonic waves to commercial-scale dewatering and classifying of fine coal. Pre-treating minus 28 mesh Upper Freeport Seam coal using an ultrasonic tray device improved subsequent dewatering by a vacuum disc filter after thickening in a cyclone, but it did not improve dewatering by a screen-bowl centrifuge after cycloning. Dewatering of Pittsburgh Seam coal also improved when the coal was ultrasonically treated, but it only manifested during thickening in the cyclone. Cycloning also increased the removal of fine, high-ash content clay particles from Pittsburgh Seam coal. In contrast, ultrasonically-treating Upper Freeport Seam coal did not improve subsequent classifying by a rapped sieve bend. Based on a specific example of results in this test work for Upper Freeport Seam coal, using an ultrasonic tray to aid dewatering of finely-sized coal can be economically beneficial. For other coals and dewatering devices, however, the economics for using ultrasonic trays to enhance fine coal dewatering will differ.

  19. 14 CFR 91.325 - Primary category aircraft: Operating limitations.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 2 2011-01-01 2011-01-01 false Primary category aircraft: Operating... Flight Operations § 91.325 Primary category aircraft: Operating limitations. (a) No person may operate a primary category aircraft carrying persons or property for compensation or hire. (b) No person may...

  20. 14 CFR 91.325 - Primary category aircraft: Operating limitations.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 2 2013-01-01 2013-01-01 false Primary category aircraft: Operating... Flight Operations § 91.325 Primary category aircraft: Operating limitations. (a) No person may operate a primary category aircraft carrying persons or property for compensation or hire. (b) No person may...

  1. 33 CFR 325.2 - Processing of applications.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... either determine that the application is complete (see 33 CFR 325.1(d)(9) and issue a public notice as... additional information or comments. (4) The district engineer will follow appendix B of 33 CFR part 230 for... the application to determine the need for a public hearing pursuant to 33 CFR part 327. (6) After...

  2. 33 CFR 325.2 - Processing of applications.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... either determine that the application is complete (see 33 CFR 325.1(d)(9) and issue a public notice as... additional information or comments. (4) The district engineer will follow Appendix B of 33 CFR part 230 for... the application to determine the need for a public hearing pursuant to 33 CFR part 327. (6) After...

  3. 33 CFR 325.2 - Processing of applications.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... either determine that the application is complete (see 33 CFR 325.1(d)(9) and issue a public notice as... additional information or comments. (4) The district engineer will follow Appendix B of 33 CFR part 230 for... the application to determine the need for a public hearing pursuant to 33 CFR part 327. (6) After...

  4. 36 CFR 13.325 - Most directly affected Native Corporation.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Visitor Services § 13.325 Most directly affected Native Corporation. (a) Before the award of the first visitor service authorization in a park area... Native Corporation interested in providing visitor services within the applicable park area to submit...

  5. 36 CFR 13.325 - Most directly affected Native Corporation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Visitor Services § 13.325 Most directly affected Native Corporation. (a) Before the award of the first visitor service authorization in a park area... Native Corporation interested in providing visitor services within the applicable park area to submit...

  6. 24 CFR 891.325 - Lead-based paint requirements.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Lead-based paint requirements....

  7. 24 CFR 891.325 - Lead-based paint requirements.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based... 24 Housing and Urban Development 4 2014-04-01 2014-04-01 false Lead-based paint requirements....

  8. 24 CFR 891.325 - Lead-based paint requirements.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Lead-based paint requirements....

  9. 24 CFR 891.325 - Lead-based paint requirements.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... Section 811 Supportive Housing for Persons With Disabilities § 891.325 Lead-based paint requirements. The requirements of the Lead-Based Paint Poisoning Prevention Act (42 U.S.C. 4821-4846), the Residential Lead-Based... 24 Housing and Urban Development 4 2013-04-01 2013-04-01 false Lead-based paint requirements....

  10. 40 CFR 89.325 - Engine intake air temperature measurement.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine intake air temperature... Test Equipment Provisions § 89.325 Engine intake air temperature measurement. (a) Engine intake air temperature measurement must be made within 122 cm of the engine. The measurement location must be made...

  11. 24 CFR 964.325 - Notice of funding availability.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 4 2012-04-01 2012-04-01 false Notice of funding availability. 964... Centers (FIC) Program § 964.325 Notice of funding availability. A Notice of Funding Availability will be published periodically in the Federal Register containing the amounts of funds available, funding...

  12. 9 CFR 113.325 - Avian Encephalomyelitis Vaccine.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... OF AGRICULTURE VIRUSES, SERUMS, TOXINS, AND ANALOGOUS PRODUCTS; ORGANISMS AND VECTORS STANDARD REQUIREMENTS Live Virus Vaccines § 113.325 Avian Encephalomyelitis Vaccine. Avian Encephalomyelitis Vaccine shall be prepared from virus-bearing tissues or fluids from embryonated chicken eggs. Only Master...

  13. 9 CFR 113.325 - Avian Encephalomyelitis Vaccine.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... OF AGRICULTURE VIRUSES, SERUMS, TOXINS, AND ANALOGOUS PRODUCTS; ORGANISMS AND VECTORS STANDARD REQUIREMENTS Live Virus Vaccines § 113.325 Avian Encephalomyelitis Vaccine. Avian Encephalomyelitis Vaccine shall be prepared from virus-bearing tissues or fluids from embryonated chicken eggs. Only Master...

  14. 9 CFR 113.325 - Avian Encephalomyelitis Vaccine.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... OF AGRICULTURE VIRUSES, SERUMS, TOXINS, AND ANALOGOUS PRODUCTS; ORGANISMS AND VECTORS STANDARD REQUIREMENTS Live Virus Vaccines § 113.325 Avian Encephalomyelitis Vaccine. Avian Encephalomyelitis Vaccine shall be prepared from virus-bearing tissues or fluids from embryonated chicken eggs. Only Master...

  15. 15 CFR 325.8 - Expediting the certification process.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Expediting the certification process... CERTIFICATES OF REVIEW § 325.8 Expediting the certification process. (a) Request for expedited action. (1) An... whole or in part and process the remainder of the application through the normal procedures....

  16. 36 CFR 13.325 - Most directly affected Native Corporation.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Visitor Services § 13.325 Most directly...) Location of the corporation's population center or centers; and (3) An assessment of the socioeconomic...) Distance and accessibility from the corporation's population center and/or business address to...

  17. 36 CFR 13.325 - Most directly affected Native Corporation.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Visitor Services § 13.325 Most directly...) Location of the corporation's population center or centers; and (3) An assessment of the socioeconomic...) Distance and accessibility from the corporation's population center and/or business address to...

  18. 36 CFR 13.325 - Most directly affected Native Corporation.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Visitor Services § 13.325 Most directly...) Location of the corporation's population center or centers; and (3) An assessment of the socioeconomic...) Distance and accessibility from the corporation's population center and/or business address to...

  19. 15 CFR 325.10 - Modifying or revoking a certificate.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Modifying or revoking a certificate... CERTIFICATES OF REVIEW § 325.10 Modifying or revoking a certificate. (a) Action subject to modification or revocation. The Secretary shall revoke a certificate, in whole or in part, or modify it, as the Secretary...

  20. 33 CFR 325.2 - Processing of applications.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... dredged material in ocean waters (40 CFR parts 220 to 229), if applicable, and the conclusions of the... either determine that the application is complete (see 33 CFR 325.1(d)(9) and issue a public notice as... additional information or comments. (4) The district engineer will follow Appendix B of 33 CFR part 230...

  1. 47 CFR 3.25 - Number of copies.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... AUTHORITIES IN MARITIME AND MARITIME MOBILE-SATELLITE RADIO SERVICES Application Procedures § 3.25 Number of copies. One original and one copy of FCC Form 44, “Application For Certification As An Accounting... application forms will be considered. Applications should be mailed at least 90 days prior to...

  2. 49 CFR 325.75 - Ground surface correction factors. 1

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... determine whether the motor vehicle conforms to the Standards for Highway Operations, 40 CFR 202.20. (b... the motor vehicle conforms to the Standard for Operation Under Stationary Test, 40 CFR 202.21. ... 1 Table 1, in § 325.7 is a tabulation of the maximum allowable sound level readings taking...

  3. 49 CFR 325.75 - Ground surface correction factors. 1

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... determine whether the motor vehicle conforms to the Standards for Highway Operations, 40 CFR 202.20. (b... the motor vehicle conforms to the Standard for Operation Under Stationary Test, 40 CFR 202.21. ... 1 Table 1, in § 325.7 is a tabulation of the maximum allowable sound level readings taking...

  4. 40 CFR 89.325 - Engine intake air temperature measurement.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 21 2013-07-01 2013-07-01 false Engine intake air temperature... Test Equipment Provisions § 89.325 Engine intake air temperature measurement. (a) Engine intake air temperature measurement must be made within 122 cm of the engine. The measurement location must be made...

  5. 40 CFR 89.325 - Engine intake air temperature measurement.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 20 2014-07-01 2013-07-01 true Engine intake air temperature... Test Equipment Provisions § 89.325 Engine intake air temperature measurement. (a) Engine intake air temperature measurement must be made within 122 cm of the engine. The measurement location must be made...

  6. 40 CFR 89.325 - Engine intake air temperature measurement.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 21 2012-07-01 2012-07-01 false Engine intake air temperature... Test Equipment Provisions § 89.325 Engine intake air temperature measurement. (a) Engine intake air temperature measurement must be made within 122 cm of the engine. The measurement location must be made...

  7. 40 CFR 89.325 - Engine intake air temperature measurement.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Engine intake air temperature... Test Equipment Provisions § 89.325 Engine intake air temperature measurement. (a) Engine intake air temperature measurement must be made within 122 cm of the engine. The measurement location must be made...

  8. 14 CFR 171.325 - Maintenance and operations requirements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... (MLS) § 171.325 Maintenance and operations requirements. (a) The owner of the facility must establish an adequate maintenance system and provide MLS qualified maintenance personnel to maintain the... to maintain an MLS facility, including proficiency in maintenance procedures and the use...

  9. 14 CFR 171.325 - Maintenance and operations requirements.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... (MLS) § 171.325 Maintenance and operations requirements. (a) The owner of the facility must establish an adequate maintenance system and provide MLS qualified maintenance personnel to maintain the... to maintain an MLS facility, including proficiency in maintenance procedures and the use...

  10. 46 CFR 154.325 - Accommodation, service, and control spaces.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Equipment Ship Arrangements § 154.325 Accommodation, service, and control spaces. (a) Accommodation, service, and control spaces must be outside the cargo area. (b) If a hold space having a cargo containment..., or control space by a cruciform joint, there must be a cofferdam providing at least 760 mm (30...

  11. 12 CFR 325.205 - Methodologies and practices.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... POLICY CAPITAL MAINTENANCE Annual Stress Test § 325.205 Methodologies and practices. (a) Potential impact on capital. In conducting a stress test under this subpart, during each quarter of the planning.... (b) Controls and oversight of stress testing processes. (1) The senior management of a covered...

  12. 12 CFR 325.205 - Methodologies and practices.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... POLICY CAPITAL MAINTENANCE Annual Stress Test § 325.205 Methodologies and practices. (a) Potential impact on capital. In conducting a stress test under this subpart, during each quarter of the planning.... (b) Controls and oversight of stress testing processes. (1) The senior management of a covered...

  13. 14 CFR 152.325 - Financial status report: Airport planning.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... TRANSPORTATION (CONTINUED) AIRPORTS AIRPORT AID PROGRAM Accounting and Reporting Requirements § 152.325 Financial... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Financial status report: Airport planning... agency conducting a project for airport system planning shall submit a financial status report on a...

  14. 33 CFR 183.325 - Flotation test for persons capacity.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Flotation test for persons... SECURITY (CONTINUED) BOATING SAFETY BOATS AND ASSOCIATED EQUIPMENT Flotation Requirements for Outboard Boats Rated for Engines of 2 Horsepower or Less Tests § 183.325 Flotation test for persons...

  15. Adsorption of various alcohols on Illinois No. 6 coal in aqueous solutions

    SciTech Connect

    Kwon, K.C.; Rigby, R.R.

    1993-07-01

    Hydrophilicity, hydrophobicity and aromacity of Illinois {number_sign}6 coal in water are relatively determined by evaluating equilibrium physical/chemical adsorption of probe compounds on the coal. Experiments on equilibrium adsorption loadings of various additives on 60--200 mesh Illinois {number_sign}6 coal (DECS-2; Randolph county) were performed to investigate relatively surface properties of the coal at 25{degree}C. The additives include various alcohols, alkanes and aromatic compounds. The main objectives of this research are to evaluate relatively surface properties of raw coals, treated coals and coal minerals with the inverse liquid chromatography technique, using various probe compounds, to analyze flotation recoveries of coals with a micro-flotation apparatus in order to relate coal floatability to evaluated coal surface properties, and to delineate roles of coal-cleaning/handling additives with the inverse liquid chromatography technique.

  16. Hanford facility dangerous waste permit application, 325 hazardous waste treatment units. Revision 1

    SciTech Connect

    1997-07-01

    This report contains the Hanford Facility Dangerous Waste Permit Application for the 325 Hazardous Waste Treatment Units (325 HWTUs) which consist of the Shielded Analytical Laboratory, the 325 Building, and the 325 Collection/Loadout Station Tank. The 325 HWTUs receive, store, and treat dangerous waste generated by Hanford Facility programs. Routine dangerous and/or mixed waste treatment that will be conducted in the 325 HWTUs will include pH adjustment, ion exchange, carbon absorption, oxidation, reduction, waste concentration by evaporation, precipitation, filtration, solvent extraction, solids washing, phase separation, catalytic destruction, and solidification/stabilization.

  17. Confined helium on Lagrange meshes.

    PubMed

    Baye, D; Dohet-Eraly, J

    2015-12-21

    The Lagrange-mesh method has the simplicity of a calculation on a mesh and can have the accuracy of a variational method. It is applied to the study of a confined helium atom. Two types of confinement are considered. Soft confinements by potentials are studied in perimetric coordinates. Hard confinement in impenetrable spherical cavities is studied in a system of rescaled perimetric coordinates varying in [0,1] intervals. Energies and mean values of the distances between electrons and between an electron and the helium nucleus are calculated. A high accuracy of 11 to 15 significant figures is obtained with small computing times. Pressures acting on the confined atom are also computed. For sphere radii smaller than 1, their relative accuracies are better than 10(-10). For larger radii up to 10, they progressively decrease to 10(-3), still improving the best literature results. PMID:25732054

  18. The moving mesh code SHADOWFAX

    NASA Astrophysics Data System (ADS)

    Vandenbroucke, B.; De Rijcke, S.

    2016-07-01

    We introduce the moving mesh code SHADOWFAX, which can be used to evolve a mixture of gas, subject to the laws of hydrodynamics and gravity, and any collisionless fluid only subject to gravity, such as cold dark matter or stars. The code is written in C++ and its source code is made available to the scientific community under the GNU Affero General Public Licence. We outline the algorithm and the design of our implementation, and demonstrate its validity through the results of a set of basic test problems, which are also part of the public version. We also compare SHADOWFAX with a number of other publicly available codes using different hydrodynamical integration schemes, illustrating the advantages and disadvantages of the moving mesh technique.

  19. Implicit solvers for unstructured meshes

    NASA Technical Reports Server (NTRS)

    Venkatakrishnan, V.; Mavriplis, Dimitri J.

    1991-01-01

    Implicit methods were developed and tested for unstructured mesh computations. The approximate system which arises from the Newton linearization of the nonlinear evolution operator is solved by using the preconditioned GMRES (Generalized Minimum Residual) technique. Three different preconditioners were studied, namely, the incomplete LU factorization (ILU), block diagonal factorization, and the symmetric successive over relaxation (SSOR). The preconditioners were optimized to have good vectorization properties. SSOR and ILU were also studied as iterative schemes. The various methods are compared over a wide range of problems. Ordering of the unknowns, which affects the convergence of these sparse matrix iterative methods, is also studied. Results are presented for inviscid and turbulent viscous calculations on single and multielement airfoil configurations using globally and adaptively generated meshes.

  20. Unstructured mesh algorithms for aerodynamic calculations

    NASA Technical Reports Server (NTRS)

    Mavriplis, D. J.

    1992-01-01

    The use of unstructured mesh techniques for solving complex aerodynamic flows is discussed. The principle advantages of unstructured mesh strategies, as they relate to complex geometries, adaptive meshing capabilities, and parallel processing are emphasized. The various aspects required for the efficient and accurate solution of aerodynamic flows are addressed. These include mesh generation, mesh adaptivity, solution algorithms, convergence acceleration, and turbulence modeling. Computations of viscous turbulent two-dimensional flows and inviscid three-dimensional flows about complex configurations are demonstrated. Remaining obstacles and directions for future research are also outlined.

  1. Adaptive Mesh Refinement in CTH

    SciTech Connect

    Crawford, David

    1999-05-04

    This paper reports progress on implementing a new capability of adaptive mesh refinement into the Eulerian multimaterial shock- physics code CTH. The adaptivity is block-based with refinement and unrefinement occurring in an isotropic 2:1 manner. The code is designed to run on serial, multiprocessor and massive parallel platforms. An approximate factor of three in memory and performance improvements over comparable resolution non-adaptive calculations has-been demonstrated for a number of problems.

  2. Mesh networked unattended ground sensors

    NASA Astrophysics Data System (ADS)

    Colling, Kent; Calcutt, Wade; Winston, Mark; Jones, Barry

    2006-05-01

    McQ has developed a family of low cost unattended ground sensors that utilize self-configured, mesh network communications for wireless sensing. Intended for use in an urban environment, the area monitored by the sensor system poses a communication challenge. A discussion into the sensor's communication performance and how it affects sensor installation and the operation of the system once deployed is presented.

  3. Coal pump

    DOEpatents

    Bonin, John H.; Meyer, John W.; Daniel, Jr., Arnold D.

    1983-01-01

    A device for pressurizing pulverized coal and circulating a carrier gas is disclosed. This device has utility in a coal gasification process and eliminates the need for a separate collection hopper and eliminates the separate compressor.

  4. LES Modeling of Oxy-combustion of Pulverized Coal: Preliminary Study

    NASA Astrophysics Data System (ADS)

    Warzecha, Piotr; Boguslawski, Andrzej

    2009-12-01

    The paper presents preliminary results of pulverized coal combustion process modeling using Large Eddy Simulation. First the methodology for the testing of mesh resolution is presented. The combustion process was carried out using equilibrium model with single mixture fraction approach.

  5. SHARP/PRONGHORN Interoperability: Mesh Generation

    SciTech Connect

    Avery Bingham; Javier Ortensi

    2012-09-01

    Progress toward collaboration between the SHARP and MOOSE computational frameworks has been demonstrated through sharing of mesh generation and ensuring mesh compatibility of both tools with MeshKit. MeshKit was used to build a three-dimensional, full-core very high temperature reactor (VHTR) reactor geometry with 120-degree symmetry, which was used to solve a neutron diffusion critical eigenvalue problem in PRONGHORN. PRONGHORN is an application of MOOSE that is capable of solving coupled neutron diffusion, heat conduction, and homogenized flow problems. The results were compared to a solution found on a 120-degree, reflected, three-dimensional VHTR mesh geometry generated by PRONGHORN. The ability to exchange compatible mesh geometries between the two codes is instrumental for future collaboration and interoperability. The results were found to be in good agreement between the two meshes, thus demonstrating the compatibility of the SHARP and MOOSE frameworks. This outcome makes future collaboration possible.

  6. Automatic Mesh Coarsening for Discrete Ordinates Codes

    SciTech Connect

    Turner, Scott A.

    1999-03-11

    This paper describes the use of a ''mesh potential'' function for automatic coarsening of meshes in discrete ordinates neutral particle transport codes. For many transport calculations, a user may find it helpful to have the code determine a ''good'' neutronics mesh. The complexity of a problem involving millions of mesh cells, dozens of materials, and many energy groups makes it difficult to determine an adequate level of mesh refinement with a minimum number of cells. A method has been implemented in PARTISN (Parallel Time-dependent SN) to calculate a ''mesh potential'' in each original cell of a problem, and use this information to determine the maximum coarseness allowed in the mesh while maintaining accuracy in the solution. Results are presented for a simple x-y-z fuel/control/reflector problem.

  7. Bioprosthetic Mesh in Abdominal Wall Reconstruction

    PubMed Central

    Baumann, Donald P.; Butler, Charles E.

    2012-01-01

    Mesh materials have undergone a considerable evolution over the last several decades. There has been enhancement of biomechanical properties, improvement in manufacturing processes, and development of antiadhesive laminate synthetic meshes. The evolution of bioprosthetic mesh materials has markedly changed our indications and methods for complex abdominal wall reconstruction. The authors review the optimal properties of bioprosthetic mesh materials, their evolution over time, and their indications for use. The techniques to optimize outcomes are described using bioprosthetic mesh for complex abdominal wall reconstruction. Bioprosthetic mesh materials clearly have certain advantages over other implantable mesh materials in select indications. Appropriate patient selection and surgical technique are critical to the successful use of bioprosthetic materials for abdominal wall repair. PMID:23372454

  8. Parallelization of irregularly coupled regular meshes

    NASA Technical Reports Server (NTRS)

    Chase, Craig; Crowley, Kay; Saltz, Joel; Reeves, Anthony

    1992-01-01

    Regular meshes are frequently used for modeling physical phenomena on both serial and parallel computers. One advantage of regular meshes is that efficient discretization schemes can be implemented in a straight forward manner. However, geometrically-complex objects, such as aircraft, cannot be easily described using a single regular mesh. Multiple interacting regular meshes are frequently used to describe complex geometries. Each mesh models a subregion of the physical domain. The meshes, or subdomains, can be processed in parallel, with periodic updates carried out to move information between the coupled meshes. In many cases, there are a relatively small number (one to a few dozen) subdomains, so that each subdomain may also be partitioned among several processors. We outline a composite run-time/compile-time approach for supporting these problems efficiently on distributed-memory machines. These methods are described in the context of a multiblock fluid dynamics problem developed at LaRC.

  9. Local, Optimization-based Simplicial Mesh Smoothing

    1999-12-09

    OPT-MS is a C software package for the improvement and untangling of simplicial meshes (triangles in 2D, tetrahedra in 3D). Overall mesh quality is improved by iterating over the mesh vertices and adjusting their position to optimize some measure of mesh quality, such as element angle or aspect ratio. Several solution techniques (including Laplacian smoothing, "Smart" Laplacian smoothing, optimization-based smoothing and several combinations thereof) and objective functions (for example, element angle, sin (angle), and aspectmore » ratio) are available to the user for both two and three-dimensional meshes. If the mesh contains invalid elements (those with negative area) a different optimization algorithm for mesh untangling is provided.« less

  10. Coal desulfurization

    NASA Technical Reports Server (NTRS)

    Corcoran, William H. (Inventor); Vasilakos, Nicholas P. (Inventor); Lawson, Daniel D. (Inventor)

    1982-01-01

    A method for enhancing solubilizing mass transport of reactive agents into and out of carbonaceous materials, such as coal. Solubility parameters of mass transfer and solvent media are matched to individual peaks in the solubility parameter spectrum of coals to enhance swelling and/or dissolution. Methanol containing reactive agent carriers are found particularly effective for removing organic sulfur from coals by chlorinolysis.

  11. Electrostatic Beneficiation of Coal

    SciTech Connect

    D. Lindquist; K. B. Tennal; M. K. Mazumder

    1998-10-29

    It was suggested in the proposal that small particles, due to low inertia, may not impact on the surfaces of the tribocharger. They would, thus, not receive charge and would not be beneficiated in the electrostatic separation. A milling process was proposed in which the small particles are stirred together with larger carrier beads producing the desired contact charge exchange. A force is necessary for removing the coal particles from the carrier beads. In copying machines electrostatic force is used to pull toner particles away horn iron carrier particles which are held back by magnetic force. Aerodynamic force is used in test instruments for measuring the charge to mass ratio on toners. A similar system of milling and removal is desired for use with the small coal particles. The carrier beads need to be made of copper rather than iron. This complicates the separation process since copper is non-magnetic. We are working on coating of iron beads with a layer of copper. Dr. Robert Engleken of Arkansas State University has supplied us with several test batches of copper-coated iron in the size range of -40 +70 mesh. ` We are currently testing whether the milling process used with the copper coated iron beads produces the desired charge on the coal particles.

  12. Mesh for prolapse surgery: Why the fuss?

    PubMed

    Rajshekhar, Smita; Mukhopadhyay, Sambit; Klinge, Uwe

    2015-06-01

    Pelvic organ prolapse is a common gynaecological problem. Surgical techniques to repair prolapse have been constantly evolving to reduce the recurrence of prolapse and need for reoperation. Grafts made of synthetic and biological materials became popular in the last decade as they were intended to provide extra support to native tissue repairs. However, serious complications related to use of synthetic meshes have been reported and there is increasing medico-legal concern about mesh use in prolapse surgery. Some mesh products already have been withdrawn from the market and the FDA has introduced stricter surveillance of new and existing products. Large randomized studies comparing mesh with non-mesh procedures are lacking which creates uncertainty for the surgeon and their patients.The small cohorts of the RCTs available with short follow-up periods just allow the conclusion that the mesh repair can be helpful in the short to medium term but unfortunately are not able to prove safety for all patients. In particular, current clinical reports cannot define for which indication what material may be superior compared to non-mesh repair.Quality control through long-term individual and national mesh registries is needed to keep a record of all surgeons using mesh and all devices being used, monitoring their effectiveness and safety data. Meshes with better biocompatibility designed specifically for use in vaginal surgery may provide superior clinical results, where the reduction of complications may allow a wider range of indications. PMID:25952907

  13. 9 CFR 325.3 - Product transported within the United States as part of export movement.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Product transported within the United States as part of export movement. 325.3 Section 325.3 Animals and Animal Products FOOD SAFETY AND... PRODUCTS INSPECTION AND VOLUNTARY INSPECTION AND CERTIFICATION TRANSPORTATION § 325.3 Product...

  14. 33 CFR Appendix A to Part 325 - Permit Form and Special Conditions

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Permit Form and Special Conditions A Appendix A to Part 325 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE PROCESSING OF DEPARTMENT OF THE ARMY PERMITS Pt. 325, App. A Appendix A to Part 325—Permit Form and Special Conditions...

  15. 17 CFR 201.325 - Evidence: Presentation under oath or affirmation.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Evidence: Presentation under oath or affirmation. 201.325 Section 201.325 Commodity and Securities Exchanges SECURITIES AND EXCHANGE COMMISSION RULES OF PRACTICE Rules of Practice Rules Regarding Hearings § 201.325 Evidence:...

  16. 37 CFR 3.25 - Recording requirements for trademark applications and registrations.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... trademark applications and registrations. 3.25 Section 3.25 Patents, Trademarks, and Copyrights UNITED... ASSIGNEE Requirements for Recording § 3.25 Recording requirements for trademark applications and... registration, a legible cover sheet (see § 3.31) and one of the following must be submitted: (1) A copy of...

  17. 20 CFR 408.325 - When is your application considered filed?

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 20 Employees' Benefits 2 2011-04-01 2011-04-01 false When is your application considered filed? 408.325 Section 408.325 Employees' Benefits SOCIAL SECURITY ADMINISTRATION SPECIAL BENEFITS FOR CERTAIN WORLD WAR II VETERANS Filing Applications Filing Your Application § 408.325 When is...

  18. 20 CFR 408.325 - When is your application considered filed?

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 20 Employees' Benefits 2 2014-04-01 2014-04-01 false When is your application considered filed? 408.325 Section 408.325 Employees' Benefits SOCIAL SECURITY ADMINISTRATION SPECIAL BENEFITS FOR CERTAIN WORLD WAR II VETERANS Filing Applications Filing Your Application § 408.325 When is...

  19. 20 CFR 408.325 - When is your application considered filed?

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 20 Employees' Benefits 2 2012-04-01 2012-04-01 false When is your application considered filed? 408.325 Section 408.325 Employees' Benefits SOCIAL SECURITY ADMINISTRATION SPECIAL BENEFITS FOR CERTAIN WORLD WAR II VETERANS Filing Applications Filing Your Application § 408.325 When is...

  20. 20 CFR 408.325 - When is your application considered filed?

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 20 Employees' Benefits 2 2013-04-01 2013-04-01 false When is your application considered filed? 408.325 Section 408.325 Employees' Benefits SOCIAL SECURITY ADMINISTRATION SPECIAL BENEFITS FOR CERTAIN WORLD WAR II VETERANS Filing Applications Filing Your Application § 408.325 When is...

  1. 40 CFR 158.325 - Description of materials used to produce the product.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Description of materials used to produce the product. 158.325 Section 158.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Product Chemistry § 158.325 Description...

  2. 40 CFR 158.325 - Description of materials used to produce the product.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 25 2012-07-01 2012-07-01 false Description of materials used to produce the product. 158.325 Section 158.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Product Chemistry § 158.325 Description...

  3. 40 CFR 158.325 - Description of materials used to produce the product.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 25 2013-07-01 2013-07-01 false Description of materials used to produce the product. 158.325 Section 158.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Product Chemistry § 158.325 Description...

  4. 40 CFR 158.325 - Description of materials used to produce the product.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Description of materials used to produce the product. 158.325 Section 158.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Product Chemistry § 158.325 Description...

  5. 14 CFR 325.14 - Conformity with subpart A of part 302.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false Conformity with subpart A of part 302. 325.14 Section 325.14 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION PROCEEDINGS) PROCEDURAL REGULATIONS ESSENTIAL AIR SERVICE PROCEDURES § 325.14 Conformity...

  6. 14 CFR 325.14 - Conformity with subpart A of part 302.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false Conformity with subpart A of part 302. 325.14 Section 325.14 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION PROCEEDINGS) PROCEDURAL REGULATIONS ESSENTIAL AIR SERVICE PROCEDURES § 325.14 Conformity...

  7. 14 CFR 325.14 - Conformity with subpart A of part 302.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false Conformity with subpart A of part 302. 325.14 Section 325.14 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION PROCEEDINGS) PROCEDURAL REGULATIONS ESSENTIAL AIR SERVICE PROCEDURES § 325.14 Conformity...

  8. 14 CFR 325.14 - Conformity with subpart A of part 302.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false Conformity with subpart A of part 302. 325.14 Section 325.14 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION PROCEEDINGS) PROCEDURAL REGULATIONS ESSENTIAL AIR SERVICE PROCEDURES § 325.14 Conformity...

  9. 14 CFR 325.14 - Conformity with subpart A of part 302.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Conformity with subpart A of part 302. 325.14 Section 325.14 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION PROCEEDINGS) PROCEDURAL REGULATIONS ESSENTIAL AIR SERVICE PROCEDURES § 325.14 Conformity...

  10. 20 CFR 325.3 - Application for unemployment benefits and employment service.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 20 Employees' Benefits 1 2013-04-01 2012-04-01 true Application for unemployment benefits and employment service. 325.3 Section 325.3 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD UNEMPLOYMENT INSURANCE ACT REGISTRATION FOR RAILROAD UNEMPLOYMENT BENEFITS § 325.3 Application...

  11. 14 CFR 325.10 - Modification of the designated level of essential air service.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Modification of the designated level of essential air service. 325.10 Section 325.10 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION PROCEEDINGS) PROCEDURAL REGULATIONS ESSENTIAL AIR SERVICE PROCEDURES § 325.10 Modification of the designated level...

  12. 20 CFR 408.325 - When is your application considered filed?

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false When is your application considered filed? 408.325 Section 408.325 Employees' Benefits SOCIAL SECURITY ADMINISTRATION SPECIAL BENEFITS FOR CERTAIN WORLD WAR II VETERANS Filing Applications Filing Your Application § 408.325 When is...

  13. 20 CFR 416.325 - When an application is considered filed.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 20 Employees' Benefits 2 2012-04-01 2012-04-01 false When an application is considered filed. 416.325 Section 416.325 Employees' Benefits SOCIAL SECURITY ADMINISTRATION SUPPLEMENTAL SECURITY INCOME FOR THE AGED, BLIND, AND DISABLED Filing of Applications Applications § 416.325 When an application...

  14. 40 CFR 158.325 - Description of materials used to produce the product.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 24 2014-07-01 2014-07-01 false Description of materials used to produce the product. 158.325 Section 158.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Product Chemistry § 158.325 Description...

  15. 20 CFR 416.325 - When an application is considered filed.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 20 Employees' Benefits 2 2011-04-01 2011-04-01 false When an application is considered filed. 416.325 Section 416.325 Employees' Benefits SOCIAL SECURITY ADMINISTRATION SUPPLEMENTAL SECURITY INCOME FOR THE AGED, BLIND, AND DISABLED Filing of Applications Applications § 416.325 When an application...

  16. 20 CFR 416.325 - When an application is considered filed.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 20 Employees' Benefits 2 2014-04-01 2014-04-01 false When an application is considered filed. 416.325 Section 416.325 Employees' Benefits SOCIAL SECURITY ADMINISTRATION SUPPLEMENTAL SECURITY INCOME FOR THE AGED, BLIND, AND DISABLED Filing of Applications Applications § 416.325 When an application...

  17. 20 CFR 416.325 - When an application is considered filed.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 20 Employees' Benefits 2 2013-04-01 2013-04-01 false When an application is considered filed. 416.325 Section 416.325 Employees' Benefits SOCIAL SECURITY ADMINISTRATION SUPPLEMENTAL SECURITY INCOME FOR THE AGED, BLIND, AND DISABLED Filing of Applications Applications § 416.325 When an application...

  18. Harms titanium mesh cage fracture

    PubMed Central

    Klezl, Zdenek; Bookland, Markus J.; Wolinsky, Jean-Paul; Rezek, Zdenek; Gokaslan, Ziya L.

    2007-01-01

    Interbody fusion has become a mainstay of surgical management for lumbar fractures, tumors, spondylosis, spondylolisthesis and deformities. Over the years, it has undergone a number of metamorphoses, as novel instrumentation and approaches have arisen to reduce complications and enhance outcomes. Interbody fusion procedures are common and successful, complications are rare and most often do not involve the interbody device itself. We present here a patient who underwent an anterior L4 corpectomy with Harms cage placement and who later developed a fracture of the lumbar titanium mesh cage (TMC). This report details the presentation and management of this rare complication, as well as discusses the biomechanics underlying this rare instrumentation failure. PMID:17497187

  19. Mesh networking optimized for robotic teleoperation

    NASA Astrophysics Data System (ADS)

    Hart, Abraham; Pezeshkian, Narek; Nguyen, Hoa

    2012-06-01

    Mesh networks for robot teleoperation pose different challenges than those associated with traditional mesh networks. Unmanned ground vehicles (UGVs) are mobile and operate in constantly changing and uncontrollable environments. Building a mesh network to work well under these harsh conditions presents a unique challenge. The Manually Deployed Communication Relay (MDCR) mesh networking system extends the range of and provides non-line-of-sight (NLOS) communications for tactical and explosive ordnance disposal (EOD) robots currently in theater. It supports multiple mesh nodes, robots acting as nodes, and works with all Internet Protocol (IP)-based robotic systems. Under MDCR, the performance of different routing protocols and route selection metrics were compared resulting in a modified version of the Babel mesh networking protocol. This paper discusses this and other topics encountered during development and testing of the MDCR system.

  20. Coal liquefaction process utilizing coal/CO.sub.2 slurry feedstream

    DOEpatents

    Comolli, Alfred G.; McLean, Joseph B.

    1989-01-01

    A coal hydrogenation and liquefaction process in which particulate coal feed is pressurized to an intermediate pressure of at least 500 psig and slurried with CO.sub.2 liquid to provide a flowable coal/CO.sub.2 slurry feedstream, which is further pressurized to at least 1000 psig and fed into a catalytic reactor. The coal particle size is 50-375 mesh (U.S. Sieve Series) and provides 50-80 W % coal in the coal/CO.sub.2 slurry feedstream. Catalytic reaction conditions are maintained at 650.degree.-850.degree. F. temperature, 1000-4000 psig hydrogen partial pressure and coal feed rate of 10-100 lb coal/hr ft.sup.3 reactor volume to produce hydrocarbon gas and liquid products. The hydrogen and CO.sub.2 are recovered from the reactor effluent gaseous fraction, hydrogen is recycled to the catalytic reactor, and CO.sub.2 is liquefied and recycled to the coal slurrying step. If desired, two catalytic reaction stages close coupled together in series relation can be used. The process advantageously minimizes the recycle and processing of excess hydrocarbon liquid previously needed for slurrying the coal feed to the reactor(s).

  1. Unstructured Polyhedral Mesh Thermal Radiation Diffusion

    SciTech Connect

    Palmer, T.S.; Zika, M.R.; Madsen, N.K.

    2000-07-27

    Unstructured mesh particle transport and diffusion methods are gaining wider acceptance as mesh generation, scientific visualization and linear solvers improve. This paper describes an algorithm that is currently being used in the KULL code at Lawrence Livermore National Laboratory to solve the radiative transfer equations. The algorithm employs a point-centered diffusion discretization on arbitrary polyhedral meshes in 3D. We present the results of a few test problems to illustrate the capabilities of the radiation diffusion module.

  2. Auto-adaptive finite element meshes

    NASA Technical Reports Server (NTRS)

    Richter, Roland; Leyland, Penelope

    1995-01-01

    Accurate capturing of discontinuities within compressible flow computations is achieved by coupling a suitable solver with an automatic adaptive mesh algorithm for unstructured triangular meshes. The mesh adaptation procedures developed rely on non-hierarchical dynamical local refinement/derefinement techniques, which hence enable structural optimization as well as geometrical optimization. The methods described are applied for a number of the ICASE test cases are particularly interesting for unsteady flow simulations.

  3. Floating shock fitting via Lagrangian adaptive meshes

    NASA Technical Reports Server (NTRS)

    Vanrosendale, John

    1995-01-01

    In recent work we have formulated a new approach to compressible flow simulation, combining the advantages of shock-fitting and shock-capturing. Using a cell-centered on Roe scheme discretization on unstructured meshes, we warp the mesh while marching to steady state, so that mesh edges align with shocks and other discontinuities. This new algorithm, the Shock-fitting Lagrangian Adaptive Method (SLAM), is, in effect, a reliable shock-capturing algorithm which yields shock-fitted accuracy at convergence.

  4. Design of electrospinning mesh devices

    NASA Astrophysics Data System (ADS)

    Russo, Giuseppina; Peters, Gerrit W. M.; Solberg, Ramon H. M.; Vittoria, Vittoria

    2012-07-01

    This paper describes the features of new membranes that can act as local biomedical devices owing to their peculiar shape in the form of mesh structure. These materials are designed to provide significant effects to reduce local inflammations and improve the tissue regeneration. Lamellar Hydrotalcite loaded with Diclofenac Sodium (HTLc-DIK) was homogenously dispersed inside a polymeric matrix of Poly-caprolactone (PCL) to manufacture membranes by electrospinning technique. The experimental procedure and the criteria employed have shown to be extremely effective at increasing potentiality and related applications. The employed technique has proved to be very useful to manufacture polymeric fibers with diameters in the range of nano-micro scale. In this work a dedicated collector based on a proprietary technology of IME Technologies and Eindhoven University of Technology (TU/e) was used. It allowed to obtain devices with a macro shape of a 3D-mesh. Atomic Force Microscopy (AFM) highlights a very interesting texture of the electrospun fibers. They show a lamellar morphology that is only slightly modified by the inclusion of the interclay embedded in the devices to control the drug release phenomena.

  5. Mesh infrastructure for coupled multiprocess geophysical simulations

    SciTech Connect

    Garimella, Rao V.; Perkins, William A.; Buksas, Mike W.; Berndt, Markus; Lipnikov, Konstantin; Coon, Ethan; Moulton, John D.; Painter, Scott L.

    2014-01-01

    We have developed a sophisticated mesh infrastructure capability to support large scale multiphysics simulations such as subsurface flow and reactive contaminant transport at storage sites as well as the analysis of the effects of a warming climate on the terrestrial arctic. These simulations involve a wide range of coupled processes including overland flow, subsurface flow, freezing and thawing of ice rich soil, accumulation, redistribution and melting of snow, biogeochemical processes involving plant matter and finally, microtopography evolution due to melting and degradation of ice wedges below the surface. In addition to supporting the usual topological and geometric queries about the mesh, the mesh infrastructure adds capabilities such as identifying columnar structures in the mesh, enabling deforming of the mesh subject to constraints and enabling the simultaneous use of meshes of different dimensionality for subsurface and surface processes. The generic mesh interface is capable of using three different open source mesh frameworks (MSTK, MOAB and STKmesh) under the hood allowing the developers to directly compare them and choose one that is best suited for the application's needs. We demonstrate the results of some simulations using these capabilities as well as present a comparison of the performance of the different mesh frameworks.

  6. Mesh infrastructure for coupled multiprocess geophysical simulations

    DOE PAGESBeta

    Garimella, Rao V.; Perkins, William A.; Buksas, Mike W.; Berndt, Markus; Lipnikov, Konstantin; Coon, Ethan; Moulton, John D.; Painter, Scott L.

    2014-01-01

    We have developed a sophisticated mesh infrastructure capability to support large scale multiphysics simulations such as subsurface flow and reactive contaminant transport at storage sites as well as the analysis of the effects of a warming climate on the terrestrial arctic. These simulations involve a wide range of coupled processes including overland flow, subsurface flow, freezing and thawing of ice rich soil, accumulation, redistribution and melting of snow, biogeochemical processes involving plant matter and finally, microtopography evolution due to melting and degradation of ice wedges below the surface. In addition to supporting the usual topological and geometric queries about themore » mesh, the mesh infrastructure adds capabilities such as identifying columnar structures in the mesh, enabling deforming of the mesh subject to constraints and enabling the simultaneous use of meshes of different dimensionality for subsurface and surface processes. The generic mesh interface is capable of using three different open source mesh frameworks (MSTK, MOAB and STKmesh) under the hood allowing the developers to directly compare them and choose one that is best suited for the application's needs. We demonstrate the results of some simulations using these capabilities as well as present a comparison of the performance of the different mesh frameworks.« less

  7. RGG: Reactor geometry (and mesh) generator

    SciTech Connect

    Jain, R.; Tautges, T.

    2012-07-01

    The reactor geometry (and mesh) generator RGG takes advantage of information about repeated structures in both assembly and core lattices to simplify the creation of geometry and mesh. It is released as open source software as a part of the MeshKit mesh generation library. The methodology operates in three stages. First, assembly geometry models of various types are generated by a tool called AssyGen. Next, the assembly model or models are meshed by using MeshKit tools or the CUBIT mesh generation tool-kit, optionally based on a journal file output by AssyGen. After one or more assembly model meshes have been constructed, a tool called CoreGen uses a copy/move/merge process to arrange the model meshes into a core model. In this paper, we present the current state of tools and new features in RGG. We also discuss the parallel-enabled CoreGen, which in several cases achieves super-linear speedups since the problems fit in available RAM at higher processor counts. Several RGG applications - 1/6 VHTR model, 1/4 PWR reactor core, and a full-core model for Monju - are reported. (authors)

  8. Mesh plug repair and groin hernia surgery.

    PubMed

    Robbins, A W; Rutkow, I M

    1998-12-01

    Since the mid-1980s, dramatic progress has been made in the evolution of hernia surgery, highlighted by the increasing use of prosthetic mesh. Among the mesh-based "tension-free" hernioplasties, the use of mesh plugs has garnered a large number of spirited enthusiasts, and plug herniorrhaphy has become the fastest growing hernia repair currently employed by the American surgeon. To demonstrate the simplicity and effectiveness of mesh plugs, a 9-year experience with almost 3300 patients is reported. Technical details are discussed and presentation of a literature search serves to further emphasize the utilitarian nature of this elegantly unsophisticated surgical operation. PMID:9927981

  9. Method of generating a surface mesh

    DOEpatents

    Shepherd, Jason F.; Benzley, Steven; Grover, Benjamin T.

    2008-03-04

    A method and machine-readable medium provide a technique to generate and modify a quadrilateral finite element surface mesh using dual creation and modification. After generating a dual of a surface (mesh), a predetermined algorithm may be followed to generate and modify a surface mesh of quadrilateral elements. The predetermined algorithm may include the steps of generating two-dimensional cell regions in dual space, determining existing nodes in primal space, generating new nodes in the dual space, and connecting nodes to form the quadrilateral elements (faces) for the generated and modifiable surface mesh.

  10. Conformal refinement of unstructured quadrilateral meshes

    SciTech Connect

    Garmella, Rao

    2009-01-01

    We present a multilevel adaptive refinement technique for unstructured quadrilateral meshes in which the mesh is kept conformal at all times. This means that the refined mesh, like the original, is formed of only quadrilateral elements that intersect strictly along edges or at vertices, i.e., vertices of one quadrilateral element do not lie in an edge of another quadrilateral. Elements are refined using templates based on 1:3 refinement of edges. We demonstrate that by careful design of the refinement and coarsening strategy, we can maintain high quality elements in the refined mesh. We demonstrate the method on a number of examples with dynamically changing refinement regions.

  11. Low-dispersion meshes for scattering problems

    SciTech Connect

    Hakula, H.

    1996-12-31

    For scattering problems, e.g. the Helmholtz equation, the ideal mesh in 2D is a structured mesh of equilateral triangles, since the numerical dispersion and internal reflections caused by the mesh are then minimal. However, if the scattering body does not conform to the mesh, one has to add unstructured elements to the mesh. In this paper we describe a simple modification to the Rebay`s method which leads to meshes of high quality in the context of the application. Even though the Rebay`s method is a variant of Delaunay algorithms, it does include the concept of a front. By controlling the generation of fronts in the mesh we can always choose the outer boundary of the computational domain so that the mesh will be structured far from the scattering body and the only anisotropic elements are close to the body. As a result of this, one can use the same generator both for electromagnetic and flow simulations in 2D. In multi-body configurations the meshes are intimately dependent on the relative distances between the bodies.

  12. MOAB : a mesh-oriented database.

    SciTech Connect

    Tautges, Timothy James; Ernst, Corey; Stimpson, Clint; Meyers, Ray J.; Merkley, Karl

    2004-04-01

    A finite element mesh is used to decompose a continuous domain into a discretized representation. The finite element method solves PDEs on this mesh by modeling complex functions as a set of simple basis functions with coefficients at mesh vertices and prescribed continuity between elements. The mesh is one of the fundamental types of data linking the various tools in the FEA process (mesh generation, analysis, visualization, etc.). Thus, the representation of mesh data and operations on those data play a very important role in FEA-based simulations. MOAB is a component for representing and evaluating mesh data. MOAB can store structured and unstructured mesh, consisting of elements in the finite element 'zoo'. The functional interface to MOAB is simple yet powerful, allowing the representation of many types of metadata commonly found on the mesh. MOAB is optimized for efficiency in space and time, based on access to mesh in chunks rather than through individual entities, while also versatile enough to support individual entity access. The MOAB data model consists of a mesh interface instance, mesh entities (vertices and elements), sets, and tags. Entities are addressed through handles rather than pointers, to allow the underlying representation of an entity to change without changing the handle to that entity. Sets are arbitrary groupings of mesh entities and other sets. Sets also support parent/child relationships as a relation distinct from sets containing other sets. The directed-graph provided by set parent/child relationships is useful for modeling topological relations from a geometric model or other metadata. Tags are named data which can be assigned to the mesh as a whole, individual entities, or sets. Tags are a mechanism for attaching data to individual entities and sets are a mechanism for describing relations between entities; the combination of these two mechanisms is a powerful yet simple interface for representing metadata or application

  13. Application of coal petrography to the evaluation of magnetically separated dry crushed coals

    SciTech Connect

    Harris, L.A.; Hise, E.C.

    1981-01-01

    In the present study the open gradient magnetic separation method has been used to beneficiate the -30 + 100 mesh fraction of two high volatile bituminous coals. The evaluation of the effectiveness of the magnetic separation for cleaning these coals is the subject of this paper. Coal petrography in combination with scanning electron microscopy and x-ray diffractometry were used to characterize the magnetically separated coal fractions. These analyses revealed that the majority of the pyrite and non-pyrite minerals were concentrated in the positive magnetic susceptibility fractions. The bulk of the starting samples (approx. 80 weight percent) were located in the negative magnetic susceptibility fractions and showed significant reductions in pyrite and non-pyritic minerals. The magnetic separation appears to effectively split the samples into relatively clean coal and refuse.

  14. Final test report on the combustion of solvent-refined coal in a 100 hp firetube boiler

    SciTech Connect

    Pan, Y.S.; Wieczenski, D.E.; Snedden, R.B.; Bellas, G.T.; Joubert, J.I.; Curio, A.R.; Wildman, D.J.

    1982-01-01

    Although solid Solvent-Refined Coal (SRC-I) was burned successfully in a coal-designed utility boiler in 1977, the feasibility of using this fuel in more compact oil- or gas-designed units at signficantly higher heat liberation rates remained uncertain. Combustion tests were conducted at the Pittsburgh Energy Technology Center using a 100 hp (3450 lb of steam per hour) firetube boiler, designed to burn No. 6 oil. The fuel was produced at an SRC pilot plant in Wilsonville, Alabama, from high-sulfur Kentucky coal, and 0.8% sulfur and 0.3% ash. In the combustion tests, SRC was fed to the boiler in three different physical forms: (1) a slurry composed of 70% by weight SRC-I process solvent and 30% by weight solid SRC pulverized to 92% minus 200 mesh; (2) a molten liquid at approx. 600/sup 0/F, using superheated steam at 800/sup 0/F for atomization, and preheated combustion air at 400/sup 0/F in a conventional oil burner; and (3) a solid, pulverized to 90% minus 325 mesh, using preheated secondary combustion air at 550/sup 0/F. The slurry and molten forms were burned at full boiler load at a heat liberation rate of 184,000 Btu/ft/sup 3/-hr. Carbon conversion efficiencies were generally 99.7% or greater, and boiler efficiencies were about 82%, the same as when burning No. 6 fuel oil. The pulverized SRC was burned at approx. 50% of full boiler load (1656 to 1803 lb of steam per hour) due to the limitations on the burner that was available. Carbon conversion efficiencies ranged from 98.6 to 99.6%, and boiler efficiency again was about 82%. The test results indicate that SRC-I, including the solid form, can probably be burned without derating in larger oil-designed industrial boilers of watertube design. Such units usually operate at heat liberation rates in the range of 25,000-50,000 Btu/ft/sup 3/-hr, significantly lower than rates employed in these tests.

  15. Treatment and recovery of larger particles of fine oxidized coal

    SciTech Connect

    Finch, R.E.

    1980-09-16

    This invention relates to a method and treating agent for increasing the yield of larger particles of fine oxidized coal where the particle size is 28 X 100 mesh and preferably 28 X 70 mesh and where said coal particles are concentrated by froth flotation. The method consists of utilizing as a promoter an alkali metal or ammonium polyacrylate. A preferred promoter is about 0.05-1.5 lbs of sodium polyacrylate latex per ton of dry coal (0.017-0.5 lb of dry sodium polyacrylate per ton of dry coal), having an average molecular weight of about 100,000, to 1, 000,000 and more, with a preferred range of 1,000,000 or more. This preferred promoter or frothing aid for oxidized coal is a water-in-oil latex of sodium polyacrylate used with a water-inoil emulsifier and preferably used with an alcohol-type frother. The latex may be utilized neat and self inverts with the assistance of an oil-in-water surfactant and the water in the system upon application to form an oil-in-water emulsion, or it may be used as a two part system with an activator (Aqueous) to promote inversion. Additionally, the latex emulsion recovers larger particles in the size 100 mesh and greater and preferably in the range 28 X 70 mesh.

  16. Choosing corners of rectangles for mapped meshing

    SciTech Connect

    Mitchell, S.A.

    1996-12-16

    Consider mapping a regular i x j quadrilateral mesh of a rectangle onto a surface. The quality of the mapped mesh of the surface depends heavily on which vertices of the surface correspond to corners of the rectangle. The authors problem is, given an n-sided surface, chose as corners four vertices such that the surface resembles a rectangle with corners at those vertices. Note that n could be quite large, and the length and width of the rectangle, i and j, are not prespecified. In general, there is either a goal number or a prescribed number of mesh edges for each bounding curve of the surface. The goals affect the quality of the mesh, and the prescribed edges may make finding a feasible set of corners difficult. The algorithm need only work for surfaces that are roughly rectangular, particular those without large reflex angles, as otherwise an unstructured meshing algorithm is used instead. The authors report on the theory and implementation of algorithms for this problem. They also given an overview of a solution to a related problem called interval assignment: given a complex of surfaces sharing curves, globally assign the number of mesh edges or intervals for each curve such that it is possible to mesh each surface according to its prescribed quadrilateral meshing algorithm, and assigned and user-prescribed boundary mesh edges and corners. They also note a practical, constructive technique that relies on interval assignment that can generate a quadrilateral mesh of a complex of surfaces such that a compatible hexahedral mesh of the enclosed volume exists.

  17. Fine pyrite removal from coal using a placer ore jig

    SciTech Connect

    Thomson, R.S.; Aplan, F.F.

    1995-10-01

    A placer ore jig, typically used to recover fine gold, tin and diamonds from alluvial ores, has been modified to remove fine pyrite from minus 6.4 mm ({minus}1/4 inch) coal. In parallel tests, it proved to be far superior to two conventional coal jigs, the Baum and the Baum-feldspar, in removing fine pyrite from coal. The Pan-Am placer jig was found to remove essentially all of the +28 mesh pyrite and from 99% to 90%, decreasingly, in the 28 to 200 mesh range. This jig also showed a superior performance to the Baum-Type jigs in removing fine coal from its associated refuse. The superiority of the Pan-Am placer jig is related to the strong emphasis given on the suction stroke and, hence, on consolidation trickling, whereas the Baum jigs principally emphasize the pulsion stroke during jigging.

  18. Prediction and evaluation of coal cleanability

    SciTech Connect

    Straszheim, W.E.; Markuszewski, R.; Oren, G.M.

    1990-04-01

    Samples of 200-mesh Upper Freeport, Illinois No. 6, and Pittsburgh No. 8 coals being used in the DOE-sponsored development of advanced surface-based cleaning technologies at the University of Pittsburgh, the University of California at Berkeley, and at the Ames Laboratory were characterized to predict their cleanability. Scanning electron microscope-based automated image analysis (SEM-AIA) was use to measure particle size, identity, and association with the organic matrix for the mineral particles in these coals. The coal-mineral association was expressed as a function of particle mineral content and as a function of the fraction of particle surface covered by mineral matter. The results were used to predict the cleanability of these coals for density-based and surface-based cleaning processes, respectively. 4 refs., 6 figs., 1 tab.

  19. Evaluation of hyperbaric filtration for fine coal dewatering

    SciTech Connect

    Parekh, B.K. ); Hogg, R. ); Fonseca, A. )

    1992-01-01

    Most of the coal presently used by the utility industry is cleaned at preparation plants employing wet processes. Water, while being the mainstay of coal washing, is also one of the least desirable components in the final product. Coarse coal (+3/4 inch) is easily dewatered to a 3--4 percent moisture level using conventional vibrating screens and centrifuges. However, the main problem of excess product moisture occurs in fine (minus 28 mesh) coal and refuse. Even though fines may constitute only about 20 percent of a contemporary cleaning plant feed, they account for two-thirds of the product surface moisture. This high surface moisture offsets many of the benefits of coal cleaning, and can easily undercut the ongoing programs on recovery of fine clean coal from refuse as well as producing an ultra-fine super clean coal fuel. Currently, most of the coal preparation plants utilize vacuum disk type technology for dewatering of the fine coal, providing dewatered product containing about 25 percent moisture. The coal industry would prefer to have a product moisture in the range of 10 to 15 percent, thereby avoiding thermal drying of coal. Hyperbaric filtration. has shown potential in lowering moisture in fine coal to about 20 percent level. This project will develop fundamental information on particle-liquid interaction during hyperbaric filtration and apply the knowledge in developing optimum conditions for the pilot plant testing of the hyperbaric filter system.

  20. Adaptive mesh refinement in titanium

    SciTech Connect

    Colella, Phillip; Wen, Tong

    2005-01-21

    In this paper, we evaluate Titanium's usability as a high-level parallel programming language through a case study, where we implement a subset of Chombo's functionality in Titanium. Chombo is a software package applying the Adaptive Mesh Refinement methodology to numerical Partial Differential Equations at the production level. In Chombo, the library approach is used to parallel programming (C++ and Fortran, with MPI), whereas Titanium is a Java dialect designed for high-performance scientific computing. The performance of our implementation is studied and compared with that of Chombo in solving Poisson's equation based on two grid configurations from a real application. Also provided are the counts of lines of code from both sides.

  1. Coal cleaning and the removal of ash from coal

    SciTech Connect

    Robbins, L.A.

    1986-03-11

    A method is described for treating a coal containing mass to reduce the ash components which comprises: (1) crushing the mass smaller than 20 mesh; (2) slurrying the crushed mass with water and an immiscible heavier-than-water organic media employing an intense mixing sufficient to cause intimate contact of the crushed mass with each liquid component of the slurry without an appreciable attrition; (3) carrying out a mild to substantially quiescent mixing sufficient to allow some initial disengagement of the water phase and its occluded ash from the organic media phase and its occluded coal; (4) separating the water phase from the heavier-than-water media phase including their respective solids in a raked settler; (5) collecting the separated phases and freeing the solids in each phase from its liquid; (6) drying the solids by contact with a heated surface.

  2. STUDY OF SOLVENT AND CATALYST INTERACTIONS IN DIRECT COAL LIQUEFACTION

    SciTech Connect

    Michael T. Klein

    1998-10-01

    Major objectives of the present project are to develop a better understanding of the roles of the catalyst and the liquefaction solvent in the coal liquefaction process. An open question concerning the role of the catalyst is whether intimate contact between the catalyst and the coal particles is important or required. To answer this question, it had been planned to coat an active catalyst with a porous silica coating which was found to retain catalyst activity while preventing actual contact between catalyst and coal. Consultation with people in DuPont who coat catalysts for increasing abrasion resistance have indicated that only portions of the catalyst are coated by their process (spray drying) and that sections of uncoated catalyst remain. For that reason, it was decided to suspend the catalyst in a basket separated from the coal in the reactor. The basket walls were to be permeable to the liquefaction solvent but not to the coal particles. Several such baskets were constructed of stainless steel with holes which would not permit passage of coal particles larger than 30 mesh. Liquefactions run with the coal of greater than 30 mesh size gave normal conversion of coal to liquid in the absence of catalyst in the basket, but substantially increased conversion when Ni/Mo on alumina catalyst was in the basket. While this result is interesting and suggestive of some kind of mass transfer of soluble material occurring between the catalyst and the coal, it does not eliminate the possibility of breakdown of the coal particle into particle sizes permeable to the basket. Indeed, a small amount of fine coal has been found inside the basket. To determine whether fine coal from breakdown of the coal particles is responsible for the conversion, a new basket is being prepared with 0.5{micro}m pore size.

  3. EVALUATION OF LOW GRAVITY DENSE MEDIA CYCLONE PERFORMANCE IN CLEANING FINE COAL

    EPA Science Inventory

    The report gives results of 36 pilot plant tests, conducted to evaluate the performance of dense-medium cyclones in cleaning fine coal (9x100 mesh) at low specific gravity (1.3). Test variables included two orifice sizes, three medium-to-coal ratios, and six flow rates. The clean...

  4. Parallel mesh management using interoperable tools.

    SciTech Connect

    Tautges, Timothy James; Devine, Karen Dragon

    2010-10-01

    This presentation included a discussion of challenges arising in parallel mesh management, as well as demonstrated solutions. They also described the broad range of software for mesh management and modification developed by the Interoperable Technologies for Advanced Petascale Simulations (ITAPS) team, and highlighted applications successfully using the ITAPS tool suite.

  5. Conforming quadrilaterals meshes on the cubed sphere.

    SciTech Connect

    Taylor, Mark A.; Levy, Michael Nathan; Overfelt, James Robert

    2010-08-01

    The cubed sphere geometry, obtained by inscribing a cube in a sphere and mapping points between the two surfaces using a gnomonic (central) projection, is commonly used in atmospheric models because it is free of polar singularities and is well-suited for parallel computing. Global meshes on the cubed-sphere typically project uniform (square) grids from each face of the cube onto the sphere, and if refinement is desired then it is done with non-conforming meshes - overlaying the area of interest with a finer uniform mesh, which introduces so-called hanging nodes on edges along the boundary of the fine resolution area. An alternate technique is to tile each face of the cube with quadrilaterals without requiring the quads to be rectangular. These meshes allow for refinement in areas of interest with a conforming mesh, providing a smoother transition between high and low resolution portions of the grid than non-conforming refinement. The conforming meshes are demonstrated in HOMME, NCAR's High Order Method Modeling Environment, where two modifications have been made: the dependence on uniform meshes has been removed, and the ability to read arbitrary quadrilateral meshes from a previously-generated file has been added. Numerical results come from a conservative spectral element method modeling a selection of the standard shallow water test cases.

  6. Computational results for parallel unstructured mesh computations

    SciTech Connect

    Jones, M.T.; Plassmann, P.E.

    1994-12-31

    The majority of finite element models in structural engineering are composed of unstructured meshes. These unstructured meshes are often very large and require significant computational resources; hence they are excellent candidates for massively parallel computation. Parallel solution of the sparse matrices that arise from such meshes has been studied heavily, and many good algorithms have been developed. Unfortunately, many of the other aspects of parallel unstructured mesh computation have gone largely ignored. The authors present a set of algorithms that allow the entire unstructured mesh computation process to execute in parallel -- including adaptive mesh refinement, equation reordering, mesh partitioning, and sparse linear system solution. They briefly describe these algorithms and state results regarding their running-time and performance. They then give results from the 512-processor Intel DELTA for a large-scale structural analysis problem. These results demonstrate that the new algorithms are scalable and efficient. The algorithms are able to achieve up to 2.2 gigaflops for this unstructured mesh problem.

  7. 7th International Meshing Roundtable '98

    SciTech Connect

    Eldred, T.J.

    1998-10-01

    The goal of the 7th International Meshing Roundtable is to bring together researchers and developers from industry, academia, and government labs in a stimulating, open environment for the exchange of technical information related to the meshing process. In the past, the Roundtable has enjoyed significant participation from each of these groups from a wide variety of countries.

  8. Structured mesh generation with smoothness controls

    Technology Transfer Automated Retrieval System (TEKTRAN)

    In geometrically complex domains, the RL (Ryskin and Leal) orthogonal mesh generation system may cause mesh distortion and overlapping problems when using the “weak constraint” method with specified boundary point distribution for all boundaries. To resolve these problems, an improved RL system with...

  9. 21 CFR 878.3300 - Surgical mesh.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Surgical mesh. 878.3300 Section 878.3300 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Prosthetic Devices § 878.3300 Surgical mesh. (a)...

  10. 21 CFR 878.3300 - Surgical mesh.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Surgical mesh. 878.3300 Section 878.3300 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Prosthetic Devices § 878.3300 Surgical mesh. (a)...

  11. Feature recognition applications in mesh generation

    SciTech Connect

    Tautges, T.J.; Liu, S.S.; Lu, Y.; Kraftcheck, J.; Gadh, R.

    1997-06-01

    The use of feature recognition as part of an overall decomposition-based hexahedral meshing approach is described in this paper. The meshing approach consists of feature recognition, using a c-loop or hybrid c-loop method, and the use of cutting surfaces to decompose the solid model. These steps are part of an iterative process, which proceeds either until no more features can be recognized or until the model has been completely decomposed into meshable sub-volumes. This method can greatly reduce the time required to generate an all-hexahedral mesh, either through the use of more efficient meshing algorithms on more of the geometry or by reducing the amount of manual decomposition required to mesh a volume.

  12. Mesh deformation based on artificial neural networks

    NASA Astrophysics Data System (ADS)

    Stadler, Domen; Kosel, Franc; Čelič, Damjan; Lipej, Andrej

    2011-09-01

    In the article a new mesh deformation algorithm based on artificial neural networks is introduced. This method is a point-to-point method, meaning that it does not use connectivity information for calculation of the mesh deformation. Two already known point-to-point methods, based on interpolation techniques, are also presented. In contrast to the two known interpolation methods, the new method does not require a summation over all boundary nodes for one displacement calculation. The consequence of this fact is a shorter computational time of mesh deformation, which is proven by different deformation tests. The quality of the deformed meshes with all three deformation methods was also compared. Finally, the generated and the deformed three-dimensional meshes were used in the computational fluid dynamics numerical analysis of a Francis water turbine. A comparison of the analysis results was made to prove the applicability of the new method in every day computation.

  13. Modified mesh-connected parallel computers

    SciTech Connect

    Carlson, D.A. )

    1988-10-01

    The mesh-connected parallel computer is an important parallel processing organization that has been used in the past for the design of supercomputing systems. In this paper, the authors explore modifications of a mesh-connected parallel computer for the purpose of increasing the efficiency of executing important application programs. These modifications are made by adding one or more global mesh structures to the processing array. They show how our modifications allow asymptotic improvements in the efficiency of executing computations having low to medium interprocessor communication requirements (e.g., tree computations, prefix computations, finding the connected components of a graph). For computations with high interprocessor communication requirements such as sorting, they show that they offer no speedup. They also compare the modified mesh-connected parallel computer to other similar organizations including the pyramid, the X-tree, and the mesh-of-trees.

  14. A comparison of tetrahedral mesh improvement techniques

    SciTech Connect

    Freitag, L.A.; Ollivier-Gooch, C.

    1996-12-01

    Automatic mesh generation and adaptive refinement methods for complex three-dimensional domains have proven to be very successful tools for the efficient solution of complex applications problems. These methods can, however, produce poorly shaped elements that cause the numerical solution to be less accurate and more difficult to compute. Fortunately, the shape of the elements can be improved through several mechanisms, including face-swapping techniques that change local connectivity and optimization-based mesh smoothing methods that adjust grid point location. The authors consider several criteria for each of these two methods and compare the quality of several meshes obtained by using different combinations of swapping and smoothing. Computational experiments show that swapping is critical to the improvement of general mesh quality and that optimization-based smoothing is highly effective in eliminating very small and very large angles. The highest quality meshes are obtained by using a combination of swapping and smoothing techniques.

  15. Development of 325 MHz single spoke resonators at Fermilab

    SciTech Connect

    Apollinari, G.; Gonin, I.V.; Khabiboulline, T.N.; Lanfranco, G.; Mukherjee, A.; Ozelis, J.; Ristori, L.; Sergatskov, D.; Wagner, R.; Webber, R.; /Fermilab

    2008-08-01

    The High Intensity Neutrino Source (HINS) project represents the current effort at Fermilab to produce an 8-GeV proton linac based on 400 independently phased superconducting cavities. Eighteen ?=0.21 single spoke resonators, operating at 325 MHz, comprise the first stage of the linac cold section. In this paper we present the current status of the production and testing of the first two prototype cavities. This includes descriptions of the fabrication, frequency tuning, chemical polishing, high pressure rinse, and high-gradient cold tests.

  16. Update on Development of Mesh Generation Algorithms in MeshKit

    SciTech Connect

    Jain, Rajeev; Vanderzee, Evan; Mahadevan, Vijay

    2015-09-30

    MeshKit uses a graph-based design for coding all its meshing algorithms, which includes the Reactor Geometry (and mesh) Generation (RGG) algorithms. This report highlights the developmental updates of all the algorithms, results and future work. Parallel versions of algorithms, documentation and performance results are reported. RGG GUI design was updated to incorporate new features requested by the users; boundary layer generation and parallel RGG support were added to the GUI. Key contributions to the release, upgrade and maintenance of other SIGMA1 libraries (CGM and MOAB) were made. Several fundamental meshing algorithms for creating a robust parallel meshing pipeline in MeshKit are under development. Results and current status of automated, open-source and high quality nuclear reactor assembly mesh generation algorithms such as trimesher, quadmesher, interval matching and multi-sweeper are reported.

  17. Chemistry of thermally altered high volatile bituminous coals from southern Indiana

    USGS Publications Warehouse

    Walker, R.; Mastalerz, Maria; Brassell, S.; Elswick, E.; Hower, J.C.; Schimmelmann, A.

    2007-01-01

    The optical properties and chemical characteristics of two thermally altered Pennsylvanian high volatile bituminous coals, the non-coking Danville Coal Member (Ro = 0.55%) and the coking Lower Block Coal Member (Ro = 0.56%) were investigated with the purpose of understanding differences in their coking behavior. Samples of the coals were heated to temperatures of 275????C, 325????C, 375????C and 425????C, with heating times of up to one hour. Vitrinite reflectance (Ro%) rises with temperature in both coals, with the Lower Block coal exhibiting higher reflectance at 375????C and 425????C compared to the Danville coal. Petrographic changes include the concomitant disappearance of liptinites and development of vesicles in vitrinites in both coals, although neither coal developed anisotropic coke texture. At 375????C, the Lower Block coal exhibits a higher aromatic ratio, higher reflectance, higher carbon content, and lower oxygen content, all of which indicate a greater degree of aromatization at this temperature. The Lower Block coal maintains a higher CH2/CH3 ratio than the Danville coal throughout the heating experiment, indicating that the long-chain unbranched aliphatics contained in Lower Block coal liptinites are more resistant to decomposition. As the Lower Block coal contains significant amounts of liptinite (23.6%), the contribution of aliphatics from these liptinites appears to be the primary cause of its large plastic range and high fluidity. ?? 2006 Elsevier B.V. All rights reserved.

  18. Coal liquefaction with coal tar solvent

    SciTech Connect

    Gir, S.; Rhodes, D.E.

    1986-12-16

    A method is described of liquefying coal, comprising: mixing solid coal with a process solvent comprising coal tar material which has been at least partially hydrogenated under conditions which selectively hydrogenate aromatic coal tar components to hydroaromatics and which preserve the integrity of organonitrogen coal tar components, to produce a coal-solvent slurry; treating the coal-solvent slurry under coal-liquefying conditions in a liquefaction zone to produce a solution containing coal liquefaction products; and recovering coal liquefaction products from the solution.

  19. Dewatering refuse brings profits to Dorchester Coal

    SciTech Connect

    Morgan, M.; Erickson, L.

    1984-09-01

    A belt filter press is discussed which allowed Dorchester Coal's 150 tph preparation plant to meet certain objectives. The minus 28 mesh refuse had to be dewatered further for trucking and spreading in a landfill because it did not conform to regulatory requirements. The press allowed the plant to operate with a closed water circuit, brought the landfill into compliance, and reduced refuse handling problems. Moreover, the belt press system reduced refuse disposal costs.

  20. Automatic Mesh Generation of Hybrid Mesh on Valves in Multiple Positions in Feedline Systems

    NASA Technical Reports Server (NTRS)

    Ross, Douglass H.; Ito, Yasushi; Dorothy, Fredric W.; Shih, Alan M.; Peugeot, John

    2010-01-01

    Fluid flow simulations through a valve often require evaluation of the valve in multiple opening positions. A mesh has to be generated for the valve for each position and compounding. The problem is the fact that the valve is typically part of a larger feedline system. In this paper, we propose to develop a system to create meshes for feedline systems with parametrically controlled valve openings. Herein we outline two approaches to generate the meshes for a valve in a feedline system at multiple positions. There are two issues that must be addressed. The first is the creation of the mesh on the valve for multiple positions. The second is the generation of the mesh for the total feedline system including the valve. For generation of the mesh on the valve, we will describe the use of topology matching and mesh generation parameter transfer. For generation of the total feedline system, we will describe two solutions that we have implemented. In both cases the valve is treated as a component in the feedline system. In the first method the geometry of the valve in the feedline system is replaced with a valve at a different opening position. Geometry is created to connect the valve to the feedline system. Then topology for the valve is created and the portion of the topology for the valve is topology matched to the standard valve in a different position. The mesh generation parameters are transferred and then the volume mesh for the whole feedline system is generated. The second method enables the user to generate the volume mesh on the valve in multiple open positions external to the feedline system, to insert it into the volume mesh of the feedline system, and to reduce the amount of computer time required for mesh generation because only two small volume meshes connecting the valve to the feedline mesh need to be updated.

  1. Constrained CVT Meshes and a Comparison of Triangular Mesh Generators

    SciTech Connect

    Nguyen, Hoa; Burkardt, John; Gunzburger, Max; Ju, Lili; Saka, Yuki

    2009-01-01

    Mesh generation in regions in Euclidean space is a central task in computational science, and especially for commonly used numerical methods for the solution of partial differential equations, e.g., finite element and finite volume methods. We focus on the uniform Delaunay triangulation of planar regions and, in particular, on how one selects the positions of the vertices of the triangulation. We discuss a recently developed method, based on the centroidal Voronoi tessellation (CVT) concept, for effecting such triangulations and present two algorithms, including one new one, for CVT-based grid generation. We also compare several methods, including CVT-based methods, for triangulating planar domains. To this end, we define several quantitative measures of the quality of uniform grids. We then generate triangulations of several planar regions, including some having complexities that are representative of what one may encounter in practice. We subject the resulting grids to visual and quantitative comparisons and conclude that all the methods considered produce high-quality uniform grids and that the CVT-based grids are at least as good as any of the others.

  2. Characterization of the surface properties of Illinois Basin Coals

    SciTech Connect

    Demir, I.

    1991-01-01

    The overall objective of this research project is to provide fundamental data on the physical and chemical surface properties of Illinois coals, specifically those of the Illinois Basin Coal Sample Program (IBCSP). This will help coal researchers achieve an optimal match between Illinois Basin coals and potential coal cleaning and conversion processes (or at least reduce the number of coals suitable for a particular process) and may lead to improved desulfurization and increased utilization of Illinois Basin coals. The specific tasks scheduled to meet our objective are: (1) Physical Characterization: Determine total surface area, porosity, pore size and volume distributions of IBCSP coals crushed to two particle sizes, {minus}100 and {minus}400 mesh (exclusive of IBC-108 which is available only in {minus}400 mesh form), in both an unoxidized and oxidized state. (2) Chemical Characterization: Determine the surface charge (electrokinetic mobility) as a function of pH by electrophoresis and analyze the surface chemical structure of the above samples using Diffuse Reflectance Infrared Spectroscopy (DRIS). (3) Multivariate Statistical Analyses: Explore possible relationships among the newly determined surface properties and other available characterization data, including chemical and petrographic compositions, vitrinite reflectance, free swelling index, ash yield, sulfur forms, and other relevant properties.

  3. Method of modifying a volume mesh using sheet extraction

    DOEpatents

    Borden, Michael J.; Shepherd, Jason F.

    2007-02-20

    A method and machine-readable medium provide a technique to modify a hexahedral finite element volume mesh using dual generation and sheet extraction. After generating a dual of a volume stack (mesh), a predetermined algorithm may be followed to modify the volume mesh of hexahedral elements. The predetermined algorithm may include the steps of determining a sheet of hexahedral mesh elements, generating nodes for merging, and merging the nodes to delete the sheet of hexahedral mesh elements and modify the volume mesh.

  4. Combustion characterization of the blend of plant coal and recovered coal fines. Technical report, December 1, 1991--February 29, 1992

    SciTech Connect

    Singh, S.; Scaroni, A.; Miller, B.; Choudhry, V.

    1992-08-01

    The overall objective of this proposed research program is to determine the combustion characteristics of the blend derived from mixing a plant coal and recovered and clean coal fines from the pond. During this study, one plant coal and three blend samples will be prepared and utilized. The blend samples will be of a mixture of 90% plant coal + 10% fines, 85% plant coal + 15% fines, 80% plant coal + 20% fines having particle size distribution of 70% passing through -200 mesh size. These samples` combustion behavior will be examined in two different furnaces at Penn State University, i.e., a down-fired furnace and a drop-tube furnace. The down-fired furnace will be used mainly to measure the emissions and ash deposition study, while the drop tube furnace will be used to determine burning profile, combustion efficiency, etc.

  5. Layered superhydrophobic meshes for controlled drug release.

    PubMed

    Falde, Eric J; Freedman, Jonathan D; Herrera, Victoria L M; Yohe, Stefan T; Colson, Yolonda L; Grinstaff, Mark W

    2015-09-28

    Layered superhydrophobic electrospun meshes composed of poly(ε-caprolactone) (PCL) and poly(glycerol monostearate-co-ε-caprolactone) (PGC-C18) are described as a local source of chemotherapeutic delivery. Specifically, the chemotherapeutic agent SN-38 is incorporated into a central 'core' layer, between two 'shield' layers of mesh without drug. This mesh is resistant to wetting of the surface and throughout the bulk due to the pronounced hydrophobicity imparted by the high roughness of a hydrophobic polymer, PGC-C18. In serum solution, these meshes exhibit slow initial drug release over 10days corresponding to media infiltrating the shield layer, followed by steady release over >30days, as the drug-loaded core layer is wetted. This sequence of events is supported by X-ray computed tomography imaging of a contrast agent solution infiltrating the mesh. In vitro cytotoxicity data collected with Lewis Lung Carcinoma (LLC) cells are consistent with this release profile, remaining cytotoxic for over 20days, longer than the unlayered version. Finally, after subcutaneous implantation in rats, histology of meshes with and without drug demonstrated good integration and lack of adverse reaction over 28days. The drug release rates, robust superhydrophobicity, in vitro cytotoxicity of SN-38 loaded meshes, and compatibility provide key design parameters for the development of an implantable chemotherapeutic-loaded device for the prevention of local lung cancer recurrence following surgical resection. PMID:26160309

  6. Microbial desulfurization of coal. [Leptospirillum ferrooxidans

    SciTech Connect

    Andrews, G.F.; Dugan, P.R.; McIlwain, M.E.; Stevens, C.J.

    1992-03-01

    A bacterial coal depyritization process was operated at a large laboratory scale for four months treating almost 500 kg of an Illinois {number sign}6 coal supplied by the Monterey Coal Company and ground to 80% minus 100 mesh. The main features of the process were a 200-{ell} aerated trough bioreactor consisting of a channel 2.44 m long with a porous aeration tube running along its V-shaped bottom, an inclined 40 {mu}m screen for dewatering the coal slurry, and a liquid recycle stream to inoculate the incoming coal with the bacteria and ferric ion required for pyrite removal. The process was started up with large numbers of Thiobacillus ferrooxidans and Leptospirillum ferrooxidans bacteria grown on iron media in a specially built electrolysis cell. Natural selection pressures then created a mixed culture well adapted to the coal from these bacteria, smaller numbers of T. thiooxidans added later, and the bacteria carried into the system with the coal. The process was run at 2.0 < pH < 2.7 and 18{degrees}C < temperature < 22{degrees}C.

  7. Mesh optimization for microbial fuel cell cathodes constructed around stainless steel mesh current collectors

    NASA Astrophysics Data System (ADS)

    Zhang, Fang; Merrill, Matthew D.; Tokash, Justin C.; Saito, Tomonori; Cheng, Shaoan; Hickner, Michael A.; Logan, Bruce E.

    Mesh current collectors made of stainless steel (SS) can be integrated into microbial fuel cell (MFC) cathodes constructed of a reactive carbon black and Pt catalyst mixture and a poly(dimethylsiloxane) (PDMS) diffusion layer. It is shown here that the mesh properties of these cathodes can significantly affect performance. Cathodes made from the coarsest mesh (30-mesh) achieved the highest maximum power of 1616 ± 25 mW m -2 (normalized to cathode projected surface area; 47.1 ± 0.7 W m -3 based on liquid volume), while the finest mesh (120-mesh) had the lowest power density (599 ± 57 mW m -2). Electrochemical impedance spectroscopy showed that charge transfer and diffusion resistances decreased with increasing mesh opening size. In MFC tests, the cathode performance was primarily limited by reaction kinetics, and not mass transfer. Oxygen permeability increased with mesh opening size, accounting for the decreased diffusion resistance. At higher current densities, diffusion became a limiting factor, especially for fine mesh with low oxygen transfer coefficients. These results demonstrate the critical nature of the mesh size used for constructing MFC cathodes.

  8. Path coloring on the Mesh

    SciTech Connect

    Rabani, Y.

    1996-12-31

    In the minimum path coloring problem, we are given a list of pairs of vertices of a graph. We are asked to connect each pair by a colored path. Paths of the same color must be edge disjoint. Our objective is to minimize the number of colors used. This problem was raised by Aggarwal et al and Raghavan and Upfal as a model for routing in all-optical networks. It is also related to questions in circuit routing. In this paper, we improve the O (ln N) approximation result of Kleinberg and Tardos for path coloring on the N x N mesh. We give an O(1) approximation algorithm to the number of colors needed, and a poly(ln ln N) approximation algorithm to the choice of paths and colors. To the best of our knowledge, these are the first sub-logarithmic bounds for any network other than trees, rings, or trees of rings. Our results are based on developing new techniques for randomized rounding. These techniques iteratively improve a fractional solution until it approaches integrality. They are motivated by the method used by Leighton, Maggs, and Rao for packet routing.

  9. Algebraic surface design and finite element meshes

    NASA Technical Reports Server (NTRS)

    Bajaj, Chandrajit L.

    1992-01-01

    Some of the techniques are summarized which are used in constructing C sup 0 and C sup 1 continuous meshes of low degree, implicitly defined, algebraic surface patches in three dimensional space. These meshes of low degree algebraic surface patches are used to construct accurate computer models of physical objects. These meshes are also used in the finite element simulation of physical phenomena (e.g., heat dissipation, stress/strain distributions, fluid flow characteristics) required in the computer prototyping of both the manufacturability and functionality of the geometric design.

  10. SUPERFISH accuracy dependence on mesh size

    NASA Astrophysics Data System (ADS)

    Merson, J. L.; Boicourt, G. P.

    1989-02-01

    The RF cavity code SUPERFISH is extensively used for the design of drift-tube linac (DTL), radio-frequency quadrupole (RFQ), and coupled-cavity linac (CCL) structures. It has been known for some time that considerably finer meshes are required near the nose of a drift tube to ensure accurate calculation of the resonant frequency and related secondary quantities. This paper discusses the results of numerical experiments designed to provide rules to set proper mesh sizes for DTL, RFQ, and CCL problems. During this work, SUPERFISH problems involving more than 100,000 mesh points were solved.

  11. Abdominal wall reconstruction with implantable meshes.

    PubMed

    Masden, Derek; Felder, John M; Iorio, Matthew L; Bhanot, Parag; Attinger, Christopher E

    2011-01-01

    Abdominal wall defects present a difficult problem for the reconstructive surgeon. Over the years, numerous implantable materials have becomes available to aid the surgeon in recreating the abdominal wall. This spectrum of implants includes permanent synthetic meshes, absorbable meshes, composite meshes and biomaterials. This review includes the pros and cons for the commercially available abdominal wall implants as well as a review of the literature regarding outcomes for each material. This review will provide the surgeon with current evidence-based information on implantable abdominal materials to be able to make a more informed decision about which implant to use. PMID:21663579

  12. Application of mesh network radios to UGS

    NASA Astrophysics Data System (ADS)

    Calcutt, Wade; Jones, Barry; Roeder, Brent

    2008-04-01

    During the past five years McQ has been actively pursuing integrating and applying wireless mesh network radios as a communications solution for unattended ground sensor (UGS) systems. This effort has been rewarded with limited levels of success and has ultimately resulted in a corporate position regarding the use of mesh network radios for UGS systems. A discussion into the background of the effort, the challenges of implementing commercial off-the-shelf (COTS) mesh radios with UGSs, the tradeoffs involved, and an overview of the future direction is presented.

  13. H(curl) Auxiliary Mesh Preconditioning

    SciTech Connect

    Kolev, T V; Pasciak, J E; Vassilevski, P S

    2006-08-31

    This paper analyzes a two-level preconditioning scheme for H(curl) bilinear forms. The scheme utilizes an auxiliary problem on a related mesh that is more amenable for constructing optimal order multigrid methods. More specifically, we analyze the case when the auxiliary mesh only approximately covers the original domain. The latter assumption is important since it allows for easy construction of nested multilevel spaces on regular auxiliary meshes. Numerical experiments in both two and three space dimensions illustrate the optimal performance of the method.

  14. Engagement of Metal Debris into Gear Mesh

    NASA Technical Reports Server (NTRS)

    handschuh, Robert F.; Krantz, Timothy L.

    2010-01-01

    A series of bench-top experiments was conducted to determine the effects of metallic debris being dragged through meshing gear teeth. A test rig that is typically used to conduct contact fatigue experiments was used for these tests. Several sizes of drill material, shim stock and pieces of gear teeth were introduced and then driven through the meshing region. The level of torque required to drive the "chip" through the gear mesh was measured. From the data gathered, chip size sufficient to jam the mechanism can be determined.

  15. The Mulled Coal process: An advanced fine coal preparation technology used to improve the handling characteristics of fine wet coal products

    SciTech Connect

    Jamison, P.R.

    1996-12-31

    The Mulled Coal process is a simple low cost method of improving the handling characteristics of the fine wet coal. The process involves the addition of a specifically formulated reagent to fine wet coal by mixing the two together in a pug mill. The converted material (Mulled Coal) retains some of its original surface moisture, but it handles, stores and transports like dry coal. It does not cause any of the sticking, fouling, bridging and freezing problems normally associated with fine wet coal, and, unlike thermally dried fine coal, it will not rewet and it is not dusty. In the process, large (baseball size) loosely bound sticky masses of fine wet coal particles are broken down into granules which are fairly uniform in the 28 Mesh x 0 size range. Due to the unique combination of the mixing action of the pug mill, the surface chemistry of the fine coal particles and the properties of the reagent; the individual granules are tightly bound, and they become completely enveloped by a very thin film of reagent. The reagent envelope will allow moisture out in the vapor stage, but it will not allow moisture back into the agglomerated granule. The envelope also prevents individual granules from adhering to or freezing to one another. The end result is a fine coal product which is free flowing, which is not dusty, and which will not rewet.

  16. Variable-heating-rate wire-mesh pyrolysis apparatus

    NASA Astrophysics Data System (ADS)

    Gibbins, J. R.; King, R. A. V.; Wood, R. J.; Kandiyoti, R.

    1989-06-01

    An electrically heated wire-mesh apparatus for pyrolysis studies has been developed which uses computer-driven feedback control for the heating system and thus can apply virtually any time-temperature history to the sample. Internal components are water cooled to prevent heat buildup during long runs. Using this system, coal pyrolysis has been studied at heating rates from 0.1 to about 5000 K/s and temperatures up to 1000 °C. Alternating current is used for heating; this allows the thermocouples to be attached directly to the sample holder and also makes power regulation relatively simple. For atmospheric-pressure experiments, a gas sweep can be forced through the sample holder to remove products from the heated zone and also to concentrate them in a trap which can be removed from the apparatus and weighed to establish tar yields directly. Although the design is optimized for atmospheric-pressure operation, relatively simple modifications allow operation under vacuum or at pressures of up to 160 bars in inert gas or hydrogen. The apparatus has been used to investigate a number of phenomena in coal pyrolysis and, most significantly, has demonstrated the existence of a heating-rate effect which is independent of reactor geometry.

  17. 12 CFR Appendix A to Part 325 - Statement of Policy on Risk-Based Capital

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 4 2011-01-01 2011-01-01 false Statement of Policy on Risk-Based Capital A Appendix A to Part 325 Banks and Banking FEDERAL DEPOSIT INSURANCE CORPORATION REGULATIONS AND STATEMENTS OF GENERAL POLICY CAPITAL MAINTENANCE Pt. 325, App. A Appendix A to Part 325—Statement of Policy on Risk-Based Capital Capital adequacy is one...

  18. Combustion characterization of the blend of plant coal and recovered coal fines

    SciTech Connect

    Singh, Shyam.

    1991-01-01

    The overall objective of this proposed research program is to determine the combustion characteristics of the blend derived from mixing a plant coal and recovered and clean coal fines from the pond. During this study, one plant coal and three blend samples will be prepared and utilized. The blend samples will be of a mixture of 90% plant coal + 10% fines, 85% plant coal + 15% fines, 80% plant coal + 20% fines having particle size distribution of 70% passing through {minus}200 mesh size. These samples' combustion behavior will be examined in two different furnaces at Penn State University, i.e., a down-fired furnace and a drop-tube furnace. The down-fired furnace will be used mainly to measure the emissions and ash deposition study, while the drop tube furnace will be used to determine burning profile, combustion efficiency, etc. This report covers the first quarter's progress. Major activities during this period were focused on finding the plants where a demo MTU column will be installed to prepare the samples needed to characterize the combustion behavior of slurry effluents. Also, a meeting was held at Penn State University to discuss the availability of the laboratory furnace for testing the plant coal/recovered coal fines blends.

  19. Numerical simulation of H2/air detonation using unstructured mesh

    NASA Astrophysics Data System (ADS)

    Togashi, Fumiya; Löhner, Rainald; Tsuboi, Nobuyuki

    2009-06-01

    To explore the capability of unstructured mesh to simulate detonation wave propagation phenomena, numerical simulation of H2/air detonation using unstructured mesh was conducted. The unstructured mesh has several adv- antages such as easy mesh adaptation and flexibility to the complicated configurations. To examine the resolution dependency of the unstructured mesh, several simulations varying the mesh size were conducted and compared with a computed result using a structured mesh. The results show that the unstructured mesh solution captures the detailed structure of detonation wave, as well as the structured mesh solution. To capture the detailed detonation cell structure, the unstructured mesh simulations required at least twice, ideally 5times the resolution of structured mesh solution.

  20. Grid adaptation using chimera composite overlapping meshes

    NASA Technical Reports Server (NTRS)

    Kao, Kai-Hsiung; Liou, Meng-Sing; Chow, Chuen-Yen

    1994-01-01

    The objective of this paper is to perform grid adaptation using composite overlapping meshes in regions of large gradient to accurately capture the salient features during computation. The chimera grid scheme, a multiple overset mesh technique, is used in combination with a Navier-Stokes solver. The numerical solution is first converged to a steady state based on an initial coarse mesh. Solution-adaptive enhancement is then performed by using a secondary fine grid system which oversets on top of the base grid in the high-gradient region, but without requiring the mesh boundaries to join in any special way. Communications through boundary interfaces between those separated grids are carried out using trilinear interpolation. Application to the Euler equations for shock reflections and to shock wave/boundary layer interaction problem are tested. With the present method, the salient features are well-resolved.