Science.gov

Sample records for 3d dielectric layers

  1. Thin-dielectric-layer engineering for 3D nanostructure integration using an innovative planarization approach

    NASA Astrophysics Data System (ADS)

    Guerfi, Y.; Doucet, J. B.; Larrieu, G.

    2015-10-01

    Three-dimensional (3D) nanostructures are emerging as promising building blocks for a large spectrum of applications. One critical issue in integration regards mastering the thin, flat, and chemically stable insulating layer that must be implemented on the nanostructure network in order to build striking nano-architectures. In this letter, we report an innovative method for nanoscale planarization on 3D nanostructures by using hydrogen silesquioxane as a spin-on-glass (SOG) dielectric material. To decouple the thickness of the final layer from the height of the nanostructure, we propose to embed the nanowire network in the insulator layer by exploiting the planarizing properties of the SOG approach. To achieve the desired dielectric thickness, the structure is chemically etched back with a highly diluted solution to control the etch rate precisely. The roughness of the top surface was less than 2 nm. There were no surface defects and the planarity was excellent, even in the vicinity of the nanowires. This newly developed process was used to realize a multilevel stack architecture with sub-deca-nanometer-range layer thickness.

  2. Printing 3D dielectric elastomer actuators for soft robotics

    NASA Astrophysics Data System (ADS)

    Rossiter, Jonathan; Walters, Peter; Stoimenov, Boyko

    2009-03-01

    We present a new approach to the fabrication of soft dielectric elastomer actuators using a 3D printing process. Complete actuators including active membranes and support structures can be 3D printed in one go, resulting in a great improvement in fabrication speed and increases in accuracy and consistency. We describe the fabrication process and present force and displacement results for a double-membrane antagonistic actuator. In this structure controlled prestrain is applied by the simple process of pressing together two printed actuator halves. The development of 3D printable soft actuators will have a large impact on many application areas including engineering, medicine and the emerging field of soft robotics.

  3. Metallic and 3D-printed dielectric helical terahertz waveguides.

    PubMed

    Vogt, Dominik Walter; Anthony, Jessienta; Leonhardt, Rainer

    2015-12-28

    We investigate guidance of Terahertz (THz) radiation in metallic and 3D-printed dielectric helical waveguides in the frequency range from 0.2 to 1 THz. Our experimental results obtained from THz time-domain spectroscopy (THz-TDS) measurements are in very good agreement with finite-difference time-domain (FDTD) simulations. We observe single-mode, low loss and low dispersive propagation of THz radiation in metallic helical waveguides over a broad bandwidth. The 3D-printed dielectric helical waveguides have substantially extended the bandwidth of a low loss dielectric tube waveguide as observed from the experimental and simulation results. The high flexibility of the helical design allows an easy incorporation into bench top THz devices. PMID:26832000

  4. Monolithic 3D CMOS Using Layered Semiconductors.

    PubMed

    Sachid, Angada B; Tosun, Mahmut; Desai, Sujay B; Hsu, Ching-Yi; Lien, Der-Hsien; Madhvapathy, Surabhi R; Chen, Yu-Ze; Hettick, Mark; Kang, Jeong Seuk; Zeng, Yuping; He, Jr-Hau; Chang, Edward Yi; Chueh, Yu-Lun; Javey, Ali; Hu, Chenming

    2016-04-01

    Monolithic 3D integrated circuits using transition metal dichalcogenide materials and low-temperature processing are reported. A variety of digital and analog circuits are implemented on two sequentially integrated layers of devices. Inverter circuit operation at an ultralow supply voltage of 150 mV is achieved, paving the way to high-density, ultralow-voltage, and ultralow-power applications. PMID:26833783

  5. 3D geometry applied to atmospheric layers

    NASA Astrophysics Data System (ADS)

    Nadjib Kouahla, Mohamed; Moreels, Guy; Faivre, Michael

    Epipolar geometry is an efficient method for generating 3D representations of objects. Here we present an original application of this method to the case of atmospheric layers. Two synchronized simultaneous images of the same scene are taken in two sites at a distance D. The 36*36 fields of view are oriented face to face along the same line of sight, but in opposite directions. The elevation angle of the optical axis above the horizon is 17. The observed objects are airglow emissions or cirrus clouds or aircraft trails. In the case of clouds, the shape of the objects is diffuse. To obtain a superposition of the common observed zone, it is necessary to calculate a normalized cross-correlation coefficient (NCC) to identify pairs of matching points in both images. The perspective effect in the rectangular images is inverted to produce a satellite-type view of the atmospheric layer as could be seen from an overlying satellite. We developed a triangulation algorithm to retrieve the 3D surface of the observed layer. The stereoscopic method was used to retrieve the wavy structure of the OH emissive layer at the altitude of 87 km. The distance between the observing sites was 600 km. Results obtained in Peru from the sites of Cerro Cosmos and Cerro Verde will be presented. We are currently extending the stereoscopic procedure to the study of troposphere cirruses, of natural origin or induced by aircraft engines. In this case, the distance between observation sites is D 60 km.

  6. Gold Nanoparticle Synthesis by 3D Integrated Micro-solution Plasma in a 3D Printed Artificial Porous Dielectric Material

    NASA Astrophysics Data System (ADS)

    Sotoda, Naoya; Tanaka, Kenji; Shirafuji, Tatsuru

    2015-09-01

    Plasma in contact with HAuCl4 aqueous solution can promote the synthesis of gold nanoparticles. To scale up this process, we have developed 3D integrated micro-solution plasma (3D IMSP). It can generate a large number of argon microplasmas in contact with the aqueous solution flowing in a porous dielectric material. The porous dielectric material in our prototype 3D IMSP reactor, however, consists of non-regularly arranged random-sized pores. These pore parameters may be the parameters for controlling the size and dispersion of synthesized gold nanoparticles. We have hence fabricated a 3D IMSP reactor with an artificial porous dielectric material that has regularly arranged same-sized pores by using a 3D printer. We have applied the reactor to the gold- nanoparticle synthesis. We have confirmed the synthesis of gold nanoparticles through the observation of a plasmon resonance absorption peak at 550 nm in the HAuCl4 aqueous solution treated with 3D IMSP. The size and distribution of the synthesized gold nanoparticles are under investigation. We expect that these characteristics of the gold nanoparticles can be manipulated by changing pore size and their distribution in the porous dielectric material.

  7. Single-layer graphene-assembled 3D porous carbon composites with PVA and Fe₃O₄ nano-fillers: an interface-mediated superior dielectric and EMI shielding performance.

    PubMed

    Rao, B V Bhaskara; Yadav, Prasad; Aepuru, Radhamanohar; Panda, H S; Ogale, Satishchandra; Kale, S N

    2015-07-28

    In this study, a novel composite of Fe3O4 nanofiller-decorated single-layer graphene-assembled porous carbon (SLGAPC) with polyvinyl alcohol (PVA) having flexibility and a density of 0.75 g cm(-3) is explored for its dielectric and electromagnetic interference (EMI) response properties. The composite is prepared by the solution casting method and its constituents are optimized as 15 wt% SLGAPC and 20 wt% Fe3O4 through a novel solvent relaxation nuclear magnetic resonance experiment. The PVA-SLGAPC-Fe3O4 composite shows high dielectric permittivity in the range of 1 Hz-10 MHz, enhanced by a factor of 4 as compared to that of the PVA-SLGAPC composite, with a reduced loss by a factor of 2. The temperature dependent dielectric properties reveal the activation energy behaviour with reference to the glass transition temperature (80 °C) of PVA. The dielectric hysteresis with the temperature cycle reveals a remnant polarization. The enhanced dielectric properties are suggested to be the result of improvement in the localized polarization of the integrated interface system (Maxwell-Wagner-Sillars (MWS) polarization) formed by the uniform adsorption of Fe3O4 on the surface of SLGAPC conjugated with PVA. The EMI shielding property of the composite with a low thickness of 0.3 mm in the X-band (8.2-12.4 GHz) shows a very impressive shielding efficiency of ∼15 dB and a specific shielding effectiveness of 20 dB (g cm(-3))(-1), indicating the promising character of this material for flexible EMI shielding applications. PMID:26105548

  8. Pseudo single crystal, direct-band-gap Ge{sub 0.89}Sn{sub 0.11} on amorphous dielectric layers towards monolithic 3D photonic integration

    SciTech Connect

    Li, Haofeng; Brouillet, Jeremy; Wang, Xiaoxin; Liu, Jifeng

    2014-11-17

    We demonstrate pseudo single crystal, direct-band-gap Ge{sub 0.89}Sn{sub 0.11} crystallized on amorphous layers at <450 °C towards 3D Si photonic integration. We developed two approaches to seed the lateral single crystal growth: (1) utilize the Gibbs-Thomson eutectic temperature depression at the tip of an amorphous GeSn nanotaper for selective nucleation; (2) laser-induced nucleation at one end of a GeSn strip. Either way, the crystallized Ge{sub 0.89}Sn{sub 0.11} is dominated by a single grain >18 μm long that forms optoelectronically benign twin boundaries with others grains. These pseudo single crystal, direct-band-gap Ge{sub 0.89}Sn{sub 0.11} patterns are suitable for monolithic 3D integration of active photonic devices on Si.

  9. Lithographically-generated 3D lamella layers and their structural color

    NASA Astrophysics Data System (ADS)

    Zhang, Sichao; Chen, Yifang; Lu, Bingrui; Liu, Jianpeng; Shao, Jinhai; Xu, Chen

    2016-04-01

    Inspired by the structural color from the multilayer nanophotonic structures in Morpho butterfly wing scales, 3D lamellae layers in dielectric polymers (polymethyl methacrylate, PMMA) with n ~ 1.5 were designed and fabricated by standard top-down electron beam lithography with one-step exposure followed by an alternating development/dissolution process of PMMA/LOR (lift-off resist) multilayers. This work offers direct proof of the structural blue/green color via lithographically-replicated PMMA/air multilayers, analogous to those in real Morpho butterfly wings. The success of nanolithography in this work for the 3D lamellae structures in dielectric polymers not only enables us to gain deeper insight into the mysterious blue color of the Morpho butterfly wings, but also breaks through the bottleneck in technical development toward broad applications in gas/liquid sensors, 3D meta-materials, coloring media, and infrared imaging devices, etc.

  10. Lithographically-generated 3D lamella layers and their structural color.

    PubMed

    Zhang, Sichao; Chen, Yifang; Lu, Bingrui; Liu, Jianpeng; Shao, Jinhai; Xu, Chen

    2016-04-28

    Inspired by the structural color from the multilayer nanophotonic structures in Morpho butterfly wing scales, 3D lamellae layers in dielectric polymers (polymethyl methacrylate, PMMA) with n ∼ 1.5 were designed and fabricated by standard top-down electron beam lithography with one-step exposure followed by an alternating development/dissolution process of PMMA/LOR (lift-off resist) multilayers. This work offers direct proof of the structural blue/green color via lithographically-replicated PMMA/air multilayers, analogous to those in real Morpho butterfly wings. The success of nanolithography in this work for the 3D lamellae structures in dielectric polymers not only enables us to gain deeper insight into the mysterious blue color of the Morpho butterfly wings, but also breaks through the bottleneck in technical development toward broad applications in gas/liquid sensors, 3D meta-materials, coloring media, and infrared imaging devices, etc. PMID:27087577

  11. Encapsulation layer design and scalability in encapsulated vertical 3D RRAM

    NASA Astrophysics Data System (ADS)

    Yu, Muxi; Fang, Yichen; Wang, Zongwei; Chen, Gong; Pan, Yue; Yang, Xue; Yin, Minghui; Yang, Yuchao; Li, Ming; Cai, Yimao; Huang, Ru

    2016-05-01

    Here we propose a novel encapsulated vertical 3D RRAM structure with each resistive switching cell encapsulated by dielectric layers, contributing to both the reliability improvement of individual cells and thermal disturbance reduction of adjacent cells due to the effective suppression of unwanted oxygen vacancy diffusion. In contrast to the traditional vertical 3D RRAM, encapsulated bar-electrodes are adopted in the proposed structure substituting the previous plane-electrodes, thus encapsulated resistive switching cells can be naturally formed by simply oxidizing the tip of the metal bar-electrodes. In this work, TaO x -based 3D RRAM devices with SiO2 and Si3N4 as encapsulation layers are demonstrated, both showing significant advantages over traditional unencapsulated vertical 3D RRAM. Furthermore, it was found thermal conductivity and oxygen blocking ability are two key parameters of the encapsulation layer design influencing the scalability of vertical 3D RRAM. Experimental and simulation data show that oxygen blocking ability is more critical for encapsulation layers in the relatively large scale, while thermal conductivity becomes dominant as the stacking layers scale to the sub-10 nm regime. Finally, based on the notable impacts of the encapsulation layer on 3D RRAM scaling, an encapsulation material with both excellent oxygen blocking ability and high thermal conductivity such as AlN is suggested to be highly desirable to maximize the advantages of the proposed encapsulated structure. The findings in this work could pave the way for reliable ultrahigh-density storage applications in the big data era.

  12. Encapsulation layer design and scalability in encapsulated vertical 3D RRAM.

    PubMed

    Yu, Muxi; Fang, Yichen; Wang, Zongwei; Chen, Gong; Pan, Yue; Yang, Xue; Yin, Minghui; Yang, Yuchao; Li, Ming; Cai, Yimao; Huang, Ru

    2016-05-20

    Here we propose a novel encapsulated vertical 3D RRAM structure with each resistive switching cell encapsulated by dielectric layers, contributing to both the reliability improvement of individual cells and thermal disturbance reduction of adjacent cells due to the effective suppression of unwanted oxygen vacancy diffusion. In contrast to the traditional vertical 3D RRAM, encapsulated bar-electrodes are adopted in the proposed structure substituting the previous plane-electrodes, thus encapsulated resistive switching cells can be naturally formed by simply oxidizing the tip of the metal bar-electrodes. In this work, TaO x -based 3D RRAM devices with SiO2 and Si3N4 as encapsulation layers are demonstrated, both showing significant advantages over traditional unencapsulated vertical 3D RRAM. Furthermore, it was found thermal conductivity and oxygen blocking ability are two key parameters of the encapsulation layer design influencing the scalability of vertical 3D RRAM. Experimental and simulation data show that oxygen blocking ability is more critical for encapsulation layers in the relatively large scale, while thermal conductivity becomes dominant as the stacking layers scale to the sub-10 nm regime. Finally, based on the notable impacts of the encapsulation layer on 3D RRAM scaling, an encapsulation material with both excellent oxygen blocking ability and high thermal conductivity such as AlN is suggested to be highly desirable to maximize the advantages of the proposed encapsulated structure. The findings in this work could pave the way for reliable ultrahigh-density storage applications in the big data era. PMID:27044065

  13. Microwave dielectric characterisation of 3D-printed BaTiO3/ABS polymer composites

    PubMed Central

    Castles, F.; Isakov, D.; Lui, A.; Lei, Q.; Dancer, C. E. J.; Wang, Y.; Janurudin, J. M.; Speller, S. C.; Grovenor, C. R. M.; Grant, P. S.

    2016-01-01

    3D printing is used extensively in product prototyping and continues to emerge as a viable option for the direct manufacture of final parts. It is known that dielectric materials with relatively high real permittivity—which are required in important technology sectors such as electronics and communications—may be 3D printed using a variety of techniques. Among these, the fused deposition of polymer composites is particularly straightforward but the range of dielectric permittivities available through commercial feedstock materials is limited. Here we report on the fabrication of a series of composites composed of various loadings of BaTiO3 microparticles in the polymer acrylonitrile butadiene styrene (ABS), which may be used with a commercial desktop 3D printer to produce printed parts containing user-defined regions with high permittivity. The microwave dielectric properties of printed parts with BaTiO3 loadings up to 70 wt% were characterised using a 15 GHz split post dielectric resonator and had real relative permittivities in the range 2.6–8.7 and loss tangents in the range 0.005–0.027. Permittivities were reproducible over the entire process, and matched those of bulk unprinted materials, to within ~1%, suggesting that the technique may be employed as a viable manufacturing process for dielectric composites. PMID:26940381

  14. Microwave dielectric characterisation of 3D-printed BaTiO3/ABS polymer composites

    NASA Astrophysics Data System (ADS)

    Castles, F.; Isakov, D.; Lui, A.; Lei, Q.; Dancer, C. E. J.; Wang, Y.; Janurudin, J. M.; Speller, S. C.; Grovenor, C. R. M.; Grant, P. S.

    2016-03-01

    3D printing is used extensively in product prototyping and continues to emerge as a viable option for the direct manufacture of final parts. It is known that dielectric materials with relatively high real permittivity—which are required in important technology sectors such as electronics and communications—may be 3D printed using a variety of techniques. Among these, the fused deposition of polymer composites is particularly straightforward but the range of dielectric permittivities available through commercial feedstock materials is limited. Here we report on the fabrication of a series of composites composed of various loadings of BaTiO3 microparticles in the polymer acrylonitrile butadiene styrene (ABS), which may be used with a commercial desktop 3D printer to produce printed parts containing user-defined regions with high permittivity. The microwave dielectric properties of printed parts with BaTiO3 loadings up to 70 wt% were characterised using a 15 GHz split post dielectric resonator and had real relative permittivities in the range 2.6–8.7 and loss tangents in the range 0.005–0.027. Permittivities were reproducible over the entire process, and matched those of bulk unprinted materials, to within ~1%, suggesting that the technique may be employed as a viable manufacturing process for dielectric composites.

  15. Microwave dielectric characterisation of 3D-printed BaTiO3/ABS polymer composites.

    PubMed

    Castles, F; Isakov, D; Lui, A; Lei, Q; Dancer, C E J; Wang, Y; Janurudin, J M; Speller, S C; Grovenor, C R M; Grant, P S

    2016-01-01

    3D printing is used extensively in product prototyping and continues to emerge as a viable option for the direct manufacture of final parts. It is known that dielectric materials with relatively high real permittivity-which are required in important technology sectors such as electronics and communications-may be 3D printed using a variety of techniques. Among these, the fused deposition of polymer composites is particularly straightforward but the range of dielectric permittivities available through commercial feedstock materials is limited. Here we report on the fabrication of a series of composites composed of various loadings of BaTiO3 microparticles in the polymer acrylonitrile butadiene styrene (ABS), which may be used with a commercial desktop 3D printer to produce printed parts containing user-defined regions with high permittivity. The microwave dielectric properties of printed parts with BaTiO3 loadings up to 70 wt% were characterised using a 15 GHz split post dielectric resonator and had real relative permittivities in the range 2.6-8.7 and loss tangents in the range 0.005-0.027. Permittivities were reproducible over the entire process, and matched those of bulk unprinted materials, to within ~1%, suggesting that the technique may be employed as a viable manufacturing process for dielectric composites. PMID:26940381

  16. Solar cell with silicon oxynitride dielectric layer

    SciTech Connect

    Shepherd, Michael; Smith, David D

    2015-04-28

    Solar cells with silicon oxynitride dielectric layers and methods of forming silicon oxynitride dielectric layers for solar cell fabrication are described. For example, an emitter region of a solar cell includes a portion of a substrate having a back surface opposite a light receiving surface. A silicon oxynitride (SiO.sub.xN.sub.y, 0dielectric layer is disposed on the back surface of the portion of the substrate. A semiconductor layer is disposed on the silicon oxynitride dielectric layer.

  17. 3D Simulations for a Micron-Scale, Dielectric-Based Acceleration Experiment

    SciTech Connect

    Yoder, R. B.; Travish, G.; Xu Jin; Rosenzweig, J. B.

    2009-01-22

    An experimental program to demonstrate a dielectric, slab-symmetric accelerator structure has been underway for the past two years. These resonant devices are driven by a side-coupled 800-nm laser and can be configured to maintain the field profile necessary for synchronous acceleration and focusing of relativistic or nonrelativistic particles. We present 3D simulations of various versions of the structure geometry, including a metal-walled structure relevant to ongoing cold tests on resonant properties, and an all-dielectric structure to be constructed for a proof-of-principle acceleration experiment.

  18. Fabrication of dielectric and metallo-dielectric 3D nanostructures by direct laser writing and electroless plating

    NASA Astrophysics Data System (ADS)

    Radke, André; Wolff, Frank; Giessen, Harald; Klotzbücher, Thomas

    2010-02-01

    Direct laser writing via two-photon absorption allows the fabrication of three-dimensional dielectric structures with submicron resolution by tightly focusing ultrashort laser pulses into a photo-sensitive material with a high-resolution microscope objective and scanning the laser focus relative to the material. Woodpile photonic crystals fabricated with this method show a characteristic dip in transmission at near-infrared wavelengths. The spectral position of this transmission dip scales with the grating period of the fabricated crystals. Metallo-dielectric structures can be obtained by first fabricating dielectric templates with direct laser writing and subsequently coating the templates with a thin conformal metal film by electroless plating. Contiguous and conducting silver films can be deposited even on convoluted 3D geometries.

  19. High thermal conductivity lossy dielectric using a multi layer configuration

    DOEpatents

    Tiegs, Terry N.; Kiggans, Jr., James O.

    2003-01-01

    Systems and methods are described for loss dielectrics. A loss dielectric includes at least one high dielectric loss layer and at least one high thermal conductivity-electrically insulating layer adjacent the at least one high dielectric loss layer. A method of manufacturing a loss dielectric includes providing at least one high dielectric loss layer and providing at least one high thermal conductivity-electrically insulating layer adjacent the at least one high dielectric loss layer. The systems and methods provide advantages because the loss dielectrics are less costly and more environmentally friendly than the available alternatives.

  20. 3D-Printed Broadband Dielectric Tube Terahertz Waveguide with Anti-Reflection Structure

    NASA Astrophysics Data System (ADS)

    Vogt, Dominik Walter; Leonhardt, Rainer

    2016-07-01

    We demonstrate broadband, low loss, and close-to-zero dispersion guidance of terahertz (THz) radiation in a dielectric tube with an anti-reflection structure (AR-tube waveguide) in the frequency range from 0.2 to 1.0 THz. The anti-reflection structure (ARS) consists of close-packed cones in a hexagonal lattice arranged on the outer surface of the tube cladding. The feature size of the ARS is in the order of the wavelength between 0.2 and 1.0 THz. The waveguides are fabricated with the versatile and cost efficient 3D-printing method. Terahertz time-domain spectroscopy (THz-TDS) measurements as well as 3D finite-difference time-domain simulations (FDTD) are performed to extensively characterize the AR-tube waveguides. Spectrograms, attenuation spectra, effective phase refractive indices, and the group-velocity dispersion parameters β 2 of the AR-tube waveguides are presented. Both the experimental and numerical results confirm the extended bandwidth and smaller group-velocity dispersion of the AR-tube waveguide compared to a low loss plain dielectric tube THz waveguide. The AR-tube waveguide prototypes show an attenuation spectrum close to the theoretical limit given by the infinite cladding tube waveguide.

  1. Layer-by-layer assembly of 3D tissue constructs with functionalized graphene

    PubMed Central

    Shin, Su Ryon; Aghaei-Ghareh-Bolagh, Behnaz; Gao, Xiguang; Nikkhah, Mehdi; Jung, Sung Mi; Dolatshahi-Pirouz, Alireza; Kim, Sang Bok; Kim, Sun Min; Dokmeci, Mehmet R.; Tang, Xiaowu (Shirley); Khademhosseini, Ali

    2014-01-01

    Carbon-based nanomaterials have been considered as promising candidates to mimic certain structure and function of native extracellular matrix materials for tissue engineering. Significant progress has been made in fabricating carbon nanoparticle-incorporated cell culture substrates, but limited studies have been reported on the development of three-dimensional (3D) tissue constructs using these nanomaterials. Here, we present a novel approach to engineer 3D multi-layered constructs using layer-by-layer (LbL) assembly of cells separated with self-assembled graphene oxide (GO)-based thin films. The GO-based structures are shown to serve as cell adhesive sheets that effectively facilitate the formation of multi-layer cell constructs with interlayer connectivity. By controlling the amount of GO deposited in forming the thin films, the thickness of the multi-layer tissue constructs could be tuned with high cell viability. Specifically, this approach could be useful for creating dense and tightly connected cardiac tissues through the co-culture of cardiomyocytes and other cell types. In this work, we demonstrated the fabrication of stand-alone multi-layer cardiac tissues with strong spontaneous beating behavior and programmable pumping properties. Therefore, this LbL-based cell construct fabrication approach, utilizing GO thin films formed directly on cell surfaces, has great potential in engineering 3D tissue structures with improved organization, electrophysiological function, and mechanical integrity. PMID:25419209

  2. Layer-by-layer assembly of 3D tissue constructs with functionalized graphene.

    PubMed

    Shin, Su Ryon; Aghaei-Ghareh-Bolagh, Behnaz; Gao, Xiguang; Nikkhah, Mehdi; Jung, Sung Mi; Dolatshahi-Pirouz, Alireza; Kim, Sang Bok; Kim, Sun Min; Dokmeci, Mehmet R; Tang, Xiaowu Shirley; Khademhosseini, Ali

    2014-10-22

    Carbon-based nanomaterials have been considered as promising candidates to mimic certain structure and function of native extracellular matrix materials for tissue engineering. Significant progress has been made in fabricating carbon nanoparticle-incorporated cell culture substrates, but limited studies have been reported on the development of three-dimensional (3D) tissue constructs using these nanomaterials. Here, we present a novel approach to engineer 3D multi-layered constructs using layer-by-layer (LbL) assembly of cells separated with self-assembled graphene oxide (GO)-based thin films. The GO-based structures are shown to serve as cell adhesive sheets that effectively facilitate the formation of multi-layer cell constructs with interlayer connectivity. By controlling the amount of GO deposited in forming the thin films, the thickness of the multi-layer tissue constructs could be tuned with high cell viability. Specifically, this approach could be useful for creating dense and tightly connected cardiac tissues through the co-culture of cardiomyocytes and other cell types. In this work, we demonstrated the fabrication of stand-alone multi-layer cardiac tissues with strong spontaneous beating behavior and programmable pumping properties. Therefore, this LbL-based cell construct fabrication approach, utilizing GO thin films formed directly on cell surfaces, has great potential in engineering 3D tissue structures with improved organization, electrophysiological function, and mechanical integrity. PMID:25419209

  3. Aerosol based direct-write micro-additive fabrication method for sub-mm 3D metal-dielectric structures

    NASA Astrophysics Data System (ADS)

    Rahman, Taibur; Renaud, Luke; Heo, Deuk; Renn, Michael; Panat, Rahul

    2015-10-01

    The fabrication of 3D metal-dielectric structures at sub-mm length scale is highly important in order to realize low-loss passives and GHz wavelength antennas with applications in wearable and Internet-of-Things (IoT) devices. The inherent 2D nature of lithographic processes severely limits the available manufacturing routes to fabricate 3D structures. Further, the lithographic processes are subtractive and require the use of environmentally harmful chemicals. In this letter, we demonstrate an additive manufacturing method to fabricate 3D metal-dielectric structures at sub-mm length scale. A UV curable dielectric is dispensed from an Aerosol Jet system at 10-100 µm length scale and instantaneously cured to build complex 3D shapes at a length scale  <1 mm. A metal nanoparticle ink is then dispensed over the 3D dielectric using a combination of jetting action and tilted dispense head, also using the Aerosol Jet technique and at a length scale 10-100 µm, followed by the nanoparticle sintering. Simulation studies are carried out to demonstrate the feasibility of using such structures as mm-wave antennas. The manufacturing method described in this letter opens up the possibility of fabricating an entirely new class of custom-shaped 3D structures at a sub-mm length scale with potential applications in 3D antennas and passives.

  4. 3D nanopore shape control by current-stimulus dielectric breakdown

    NASA Astrophysics Data System (ADS)

    Ying, Cuifeng; Zhang, Yuechuan; Feng, Yanxiao; Zhou, Daming; Wang, Deqiang; Xiang, Yinxiao; Zhou, Wenyuan; Chen, Yongsheng; Du, Chunlei; Tian, Jianguo

    2016-08-01

    We propose a simple and cost-effect method, current-stimulus dielectric breakdown, to manipulate the 3D shapes of the nanochannels in 20-nm-thick SiNx membranes. Besides the precise control of nanopore size, the cone orientation can be determined by the pulse polarity. The cone angle of nanopores can be systematically tuned by simply changing the stimulus pulse waveform, allowing the gradual shape control from conical to obconical. After they are formed, the cone angle of these nanopores can be further tuned in a certain range by adjusting the widening pulse. Such size and 3D shape controllable abiotic nanopores can construct a constriction in the nanochannel and hence produce a sub-nm "sensing zone" to suit any desired bio-sensing or precise DNA sequencing. Using these conical nanopores, 20-nt ssDNA composed of homopolymers (poly(dA)20, poly(dC)20, and poly(dT)20) can be clearly differentiated by their ionic current signals.

  5. A microfabricated sensor for thin dielectric layers.

    PubMed

    Fierlinger, P; DeVoe, R; Flatt, B; Gratta, G; Green, M; Kolkowitz, S; Leport, F; Montero Diez, M; Neilson, R; O'Sullivan, K; Pocar, A; Wodin, J

    2008-04-01

    We describe a sensor for the measurement of thin dielectric layers capable of operation in a variety of environments. The sensor is obtained by microfabricating a capacitor with interleaved aluminum fingers, exposed to the dielectric to be measured. In particular, the device can measure thin layers of solid frozen from a liquid or gaseous medium. Sensitivity to single atomic layers is achievable in many configurations and, by utilizing fast, high sensitivity capacitance readout in a feedback system onto environmental parameters; coatings of few layers can be dynamically maintained. We discuss the design, readout, and calibration of several versions of the device optimized in different ways. We specifically dwell on the case in which atomically thin solid xenon layers are grown and stabilized, in cryogenic conditions, from a liquid xenon bath. PMID:18447546

  6. Characterization, fabrication, and analysis of soft dielectric elastomer actuators capable of complex 3D deformation

    NASA Astrophysics Data System (ADS)

    Lai, William

    Inspired by nature, the development of soft actuators has drawn large attention to provide higher flexibility and allow adaptation to more complex environment. This thesis is focused on utilizing electroactive polymers as active materials to develop soft planar dielectric elastomer actuators capable of complex 3D deformation. The potential applications of such soft actuators are in flexible robotic arms and grippers, morphing structures and flapping wings for micro aerial vehicles. The embraces design for a freestanding actuator utilizes the constrained deformation imposed by surface stiffeners on an electroactive membrane to avert the requirement of membrane pre-stretch and the supporting frames. The proposed design increases the overall actuator flexibility and degrees-of-freedom. Actuator design, fabrication, and performance are presented for different arrangement of stiffeners. Digital images correlation technique were utilized to evaluate the in-plane finite strain components, in order to elucidate the role of the stiffeners in controlling the three dimensional deformation. It was found that a key controlling factor was the localized deformation near the stiffeners, while the rest of the membrane would follow through. A detailed finite element modeling framework was developed with a user-material subroutine, built into the ABAQUS commercial finite element package. An experimentally calibrated Neo-Hookean based material model that coupled the applied electrical field to the actuator mechanical deformation was employed. The numerical model was used to optimize different geometrical features, electrode layup and stacking sequence of actuators. It was found that by splitting the stiffeners into finer segments, the force-stroke characteristics of actuator were able to be adjusted with stiffener configuration, while keeping the overall bending stiffness. The efficacy of actuators could also be greatly improved by increasing the stiffener periodicity. The developed

  7. 2D and 3D multipactor modeling in dielectric-loaded accelerator structures

    NASA Astrophysics Data System (ADS)

    Sinitsyn, Oleksandr; Nusinovich, Gregory; Antonsen, Thomas

    2010-11-01

    Multipactor (MP) is known as the avalanche growth of the number of secondary electrons emitted from a solid surface exposed to an RF electric field under vacuum conditions. MP is a severe problem in modern rf systems and, therefore, theoretical and experimental studies of MP are of great interest to the researchers working in various areas of physics and engineering. In this work we present results of MP studies in dielectric-loaded accelerator (DLA) structures. First, we show simulation results obtained with the use of the 2D self-consistent MP model (O. V. Sinitsyn, et. al., Phys. Plasmas, vol. 16, 073102 (2009)) and compare those to experimental ones obtained during recent extensive studies of DLA structures performed by Argonne National Laboratory, Naval Research Laboratory, SLAC National Accelerator Laboratory and Euclid TechLabs (C. Jing, et al., IEEE Trans. Plasma Sci., vol. 38, pp. 1354-1360 (2010)). Then we present some new results of 3D analysis of MP which include studies of particle trajectories and studies of MP development at the early stage.

  8. Direct single-layered fabrication of 3D concavo convex patterns in nano-stereolithography

    NASA Astrophysics Data System (ADS)

    Lim, T. W.; Park, S. H.; Yang, D. Y.; Kong, H. J.; Lee, K. S.

    2006-09-01

    A nano-surfacing process (NSP) is proposed to directly fabricate three-dimensional (3D) concavo convex-shaped microstructures such as micro-lens arrays using two-photon polymerization (TPP), a promising technique for fabricating arbitrary 3D highly functional micro-devices. In TPP, commonly utilized methods for fabricating complex 3D microstructures to date are based on a layer-by-layer accumulating technique employing two-dimensional sliced data derived from 3D computer-aided design data. As such, this approach requires much time and effort for precise fabrication. In this work, a novel single-layer exposure method is proposed in order to improve the fabricating efficiency for 3D concavo convex-shaped microstructures. In the NSP, 3D microstructures are divided into 13 sub-regions horizontally with consideration of the heights. Those sub-regions are then expressed as 13 characteristic colors, after which a multi-voxel matrix (MVM) is composed with the characteristic colors. Voxels with various heights and diameters are generated to construct 3D structures using a MVM scanning method. Some 3D concavo convex-shaped microstructures were fabricated to estimate the usefulness of the NSP, and the results show that it readily enables the fabrication of single-layered 3D microstructures.

  9. 3D analytical model for the SOI LDMOS with alternating silicon and high-k dielectric pillars

    NASA Astrophysics Data System (ADS)

    Yao, Jia-fei; Guo, Yu-feng; Xia, Tian; Zhang, Jun; Lin, Hong

    2016-08-01

    In this paper, a 3D analytical model for the SOI LDMOS with alternating silicon and high-k dielectric pillars (HK LDMOS) is presented. By solving the 3D Poisson's equation, the surface potential and electric field distribution are derived. A criterion for obtaining the optimal breakdown voltage and drift region doping concentration is obtained. The analytical results are well matched with the numerical results, which confirms the model validity. Based on these models and the numerical simulation, the electric field modulation mechanism and the breakdown characteristics of HK LDMOS are investigated.

  10. Monitoring time course of human whole blood coagulation using a microfluidic dielectric sensor with a 3D capacitive structure.

    PubMed

    Maji, Debnath; Suster, Michael A; Stavrou, Evi; Gurkan, Umut A; Mohseni, Pedram

    2015-08-01

    This paper reports on the design, fabrication, and testing of a microfluidic sensor for dielectric spectroscopy (DS) of human whole blood during coagulation. The sensor employs a three-dimensional (3D), parallel-plate, capacitive sensing structure with a floating electrode integrated into a microfluidic channel. Using an impedance analyzer and after a 5-point calibration, the sensor is shown to measure the real part of complex relative dielectric permittivity of human whole blood in a frequency range of 10kHz to 100MHz. The temporal variation of dielectric permittivity at 1MHz for human whole blood from three different healthy donors shows a peak in permittivity at ~ 4 to 5 minutes, which also corresponds to the onset of CaCl2-initiated coagulation of the blood sample verified visually. PMID:26737635

  11. Template-Free 3D Microprinting of Metals Using a Force-Controlled Nanopipette for Layer-by-Layer Electrodeposition.

    PubMed

    Hirt, Luca; Ihle, Stephan; Pan, Zhijian; Dorwling-Carter, Livie; Reiser, Alain; Wheeler, Jeffrey M; Spolenak, Ralph; Vörös, János; Zambelli, Tomaso

    2016-03-23

    A novel 3D printing method for voxel-by-voxel metal printing is presented. Hollow atomic force microscopy (AFM) cantilevers are used to locally supply metal ions in an electrochemical cell, enabling a localized electroplating reaction. By exploiting the deflection feedback of these probes, electrochemical 3D metal printing is, for the first time, demonstrated in a layer-by-layer fashion, enabling the fabrication of arbitrary-shaped geometries. PMID:26783090

  12. A Dielectric-Filled Waveguide Antenna Element for 3D Imaging Radar in High Temperature and Excessive Dust Conditions.

    PubMed

    Xu, Ding; Li, Zhiping; Chen, Xianzhong; Wang, Zhengpeng; Wu, Jianhua

    2016-01-01

    Three-dimensional information of the burden surface in high temperature and excessive dust industrial conditions has been previously hard to obtain. This paper presents a novel microstrip-fed dielectric-filled waveguide antenna element which is resistant to dust and high temperatures. A novel microstrip-to-dielectric-loaded waveguide transition was developed. A cylinder and cuboid composite structure was employed at the terminal of the antenna element, which improved the return loss performance and reduced the size. The proposed antenna element was easily integrated into a T-shape multiple-input multiple-output (MIMO) imaging radar system and tested in both the laboratory environment and real blast furnace environment. The measurement results show that the proposed antenna element works very well in industrial 3D imaging radar. PMID:27556469

  13. A 3D insight on the catalytic nanostructuration of few-layer graphene

    PubMed Central

    Melinte, G.; Florea, I.; Moldovan, S.; Janowska, I.; Baaziz, W.; Arenal, R.; Wisnet, A.; Scheu, C.; Begin-Colin, S.; Begin, D.; Pham-Huu, C.; Ersen, O.

    2014-01-01

    The catalytic cutting of few-layer graphene is nowadays a hot topic in materials research due to its potential applications in the catalysis field and the graphene nanoribbons fabrication. We show here a 3D analysis of the nanostructuration of few-layer graphene by iron-based nanoparticles under hydrogen flow. The nanoparticles located at the edges or attached to the steps on the FLG sheets create trenches and tunnels with orientations, lengths and morphologies defined by the crystallography and the topography of the carbon substrate. The cross-sectional analysis of the 3D volumes highlights the role of the active nanoparticle identity on the trench size and shape, with emphasis on the topographical stability of the basal planes within the resulting trenches and channels, no matter the obstacle encountered. The actual study gives a deep insight on the impact of nanoparticles morphology and support topography on the 3D character of nanostructures built up by catalytic cutting. PMID:24916201

  14. Patterning process exploration of metal 1 layer in 7nm node with 3D patterning flow simulations

    NASA Astrophysics Data System (ADS)

    Gao, Weimin; Ciofi, Ivan; Saad, Yves; Matagne, Philippe; Bachmann, Michael; Oulmane, Mohamed; Gillijns, Werner; Lucas, Kevin; Demmerle, Wolfgang; Schmoeller, Thomas

    2015-03-01

    In 7mn node (N7), the logic design requires the critical poly pitch (CPP) of 42-45nm and metal 1 (M1) pitch of 28- 32nm. Such high pattern density pushes the 193 immersion lithography solution toward its limit and also brings extremely complex patterning scenarios. The N7 M1 layer may require a self-aligned quadruple patterning (SAQP) with triple litho-etch (LE3) block process. Therefore, the whole patterning process flow requires multiple exposure+etch+deposition processes and each step introduces a particular impact on the pattern profiles and the topography. In this study, we have successfully integrated a simulation tool that enables emulation of the whole patterning flow with realistic process-dependent 3D profile and topology. We use this tool to study the patterning process variations of N7 M1 layer including the overlay control, the critical dimension uniformity (CDU) budget and the lithographic process window (PW). The resulting 3D pattern structure can be used to optimize the process flow, verify design rules, extract parasitics, and most importantly, simulate the electric field and identify hot spots for dielectric reliability. As an example application, we will report extractions of maximum electric field at M1 tipto- tip which is one of the most critical patterning locations and we will demonstrate the potential of this approach for investigating the impact of process variations on dielectric reliability. We will also present simulations of an alternative M1 patterning flow, with a single exposure block using extreme ultraviolet lithography (EUVL) and analyze its advantages compared to the LE3 block approach.

  15. Understanding and Improving the Quality of Inter-Layer Interfaces in FDM 3-D Printing

    NASA Astrophysics Data System (ADS)

    Duranty, Edward; Spradlin, Brandon; Stark, Madeline; Dadmun, Mark

    We have studied the effect of thermal history and material diffusion on inter-filament bonding in FDM 3D printed parts and developed methods to improve interlayer adhesion in 3D printed samples. The available thermal energy during the FDM print environment was determined quantitatively by tracking the temperature of the bottom most printed layer using a thermocouple attached to the print bed. The role of the thermal history of the filaments during the deposition process on the quality of inter-layer bonding in an FDM ABS part was monitored using a T-peel test and an innovative sample design. Additionally, the interfacial adhesion between 3D printed layers was improved by the addition of a chemical cross-linking agent 4,4 '-diaminodiphenylmethane (DADPM). These studies have increased our understanding of the importance of the complex thermal history of a filament in the 3D printing process and its impact on the interfaces that form during the fused deposition modeling print process. Furthermore, the chemical crosslinking process demonstrates a potential method to covalently link layers in FDM printed parts, improving the bulk strength of the part. The insight provided in this work may aid in the development of techniques that can produce FDM parts that could be used as replacement parts in structural applications, or as completely standalone products.

  16. Finite Element Code For 3D-Hydraulic Fracture Propagation Equations (3-layer).

    1992-03-24

    HYFRACP3D is a finite element program for simulation of a pseudo three-dimensional fracture geometries with a two-dimensional planar solution. The model predicts the height, width and winglength over time for a hydraulic fracture propagating in a three-layered system of rocks with variable rock mechanics properties.

  17. Monitoring adipose-derived stem cells within 3D carrier by combined dielectric spectroscopy and spectral domain optical coherence topography

    NASA Astrophysics Data System (ADS)

    Bagnaninchi, P. O.

    2010-02-01

    Monitoring non-invasively the cellular events in three dimensional carriers is a major challenge for tissue engineering and regenerative medicine that prevents time-lapsed studies over large population of sample. The potential of optical coherence tomography has been demonstrated to assess tissue formation within porous matrices. In this study we explore the combination of dielectric spectroscopy (DS) and spectral domain optical coherence tomography (SDOCT) to quality assess ADSCs loaded in three dimensional carriers. A SDOCT (930nm, FWHM 90nm) was combined to an open ended coaxial probe connected to material analyser, and broadband measurements between 20MHz and 1GHz were synchronized with Labview. Both ADSCs maintained in undifferentiated state within 3D carrier and induced towards osteoblasts were monitored with this multimodality technique and their DS spectra were acquired at high cell concentration simultaneously to 3D imaging. This multimodality technique will be instrumental to assess non-invasively cell loaded carriers for cell therapy.

  18. Intraretinal Layer Segmentation of Macular Optical Coherence Tomography Images Using Optimal 3-D Graph Search

    PubMed Central

    Abràmoff, Michael D.; Kardon, Randy; Russell, Stephen R.; Wu, Xiaodong; Sonka, Milan

    2008-01-01

    Current techniques for segmenting macular optical coherence tomography (OCT) images have been 2-D in nature. Furthermore, commercially available OCT systems have only focused on segmenting a single layer of the retina, even though each intraretinal layer may be affected differently by disease. We report an automated approach for segmenting (anisotropic) 3-D macular OCT scans into five layers. Each macular OCT dataset consisted of six linear radial scans centered at the fovea. The six surfaces defining the five layers were identified on each 3-D composite image by transforming the segmentation task into that of finding a minimum-cost closed set in a geometric graph constructed from edge/regional information and a priori determined surface smoothness and interaction constraints. The method was applied to the macular OCT scans of 12 patients (24 3-D composite image datasets) with unilateral anterior ischemic optic neuropathy (AION). Using the average of three experts’ tracings as a reference standard resulted in an overall mean unsigned border positioning error of 6.1 ± 2.9 µm, a result comparable to the interobserver variability (6.9 ± 3.3 µm). Our quantitative analysis of the automated segmentation results from AION subject data revealed that the inner retinal layer thickness for the affected eye was 24.1 µm (21%) smaller on average than for the unaffected eye (P < 0.001), supporting the need for segmenting the layers separately. PMID:18815101

  19. Effect of density gradients in confined supersonic shear layers. Part 2: 3-D modes

    NASA Technical Reports Server (NTRS)

    Peroomian, Oshin; Kelly, R. E.

    1994-01-01

    The effect of basic flow density gradients on the supersonic wall modes were investigated in Part 1 of this analysis. In that investigation only the 2-D modes were studied. Tam and Hu investigated the 3-D modes in a confined vortex sheet and reported that the first 2-D Class A mode (A01) had the highest growth rate compared to all other 2-D and 3-D modes present in the vortex sheet for that particular set of flow patterns. They also showed that this result also held true for finite thickness shear layers with delta(sub w) less than 0.125. For free shear layers, Sandham and Reynolds showed that the 3-D K-H mode became the dominant mode for M(sub c) greater than 0.6. Jackson and Grosch investigated the effect of crossflow and obliqueness on the slow and fast odes present in a M(sub c) greater than 1 environment and showed that for certain combination of crossflow and wave angles the growth rates could be increased by up to a factor of 2 with respect to the 2-D case. The case studied here is a confined shear layer shown in Part 1. All solution procedures and basic low profiles are the same as in Part 1. The effect of density gradients on the 3-D modes present in the density ratios considered in Part 1 are investigated.

  20. CFL3D Contribution to the AIAA Supersonic Shock Boundary Layer Interaction Workshop

    NASA Technical Reports Server (NTRS)

    Rumsey, Christopher L.

    2010-01-01

    This paper documents the CFL3D contribution to the AIAA Supersonic Shock Boundary Layer Interaction Workshop, held in Orlando, Florida in January 2010. CFL3D is a Reynolds-averaged Navier-Stokes code. Four shock boundary layer interaction cases are computed using a one-equation turbulence model widely used for other aerodynamic problems of interest. Two of the cases have experimental data available at the workshop, and two of the cases do not. The effect of grid, flux scheme, and thin-layer approximation are investigated. Comparisons are made to the available experimental data. All four cases exhibit strong three-dimensional behavior in and near the interaction regions, resulting from influences of the tunnel side-walls.

  1. Proton exchange membrane micro fuel cells on 3D porous silicon gas diffusion layers

    NASA Astrophysics Data System (ADS)

    Kouassi, S.; Gautier, G.; Thery, J.; Desplobain, S.; Borella, M.; Ventura, L.; Laurent, J.-Y.

    2012-10-01

    Since the 90's, porous silicon has been studied and implemented in many devices, especially in MEMS technology. In this article, we present a new approach to build miniaturized proton exchange membrane micro-fuel cells using porous silicon as a hydrogen diffusion layer. In particular, we propose an innovative process to build micro fuel cells from a “corrugated iron like” 3D structured porous silicon substrates. This structure is able to increase up to 40% the cell area keeping a constant footprint on the silicon wafer. We propose here a process route to perform electrochemically 3D porous gas diffusion layers and to deposit fuel cell active layers on such substrates. The prototype peak power performance was measured to be 90 mW cm-2 in a “breathing configuration” at room temperature. These performances are less than expected if we compare with a reference 2D micro fuel cell. Actually, the active layer deposition processes are not fully optimized but this prototype demonstrates the feasibility of these 3D devices.

  2. 3D printed broadband transformation optics based all-dielectric microwave lenses

    NASA Astrophysics Data System (ADS)

    Yi, Jianjia; Nawaz Burokur, Shah; Piau, Gérard-Pascal; de Lustrac, André

    2016-04-01

    Quasi-conformal transformation optics is applied to design electromagnetic devices for focusing and collimating applications at microwave frequencies. Two devices are studied and conceived by solving Laplace’s equation that describes the deformation of a medium in a space transformation. As validation examples, material parameters of two different lenses are derived from the analytical solutions of Laplace’s equation. The first lens is applied to produce an overall directive in-phase emission from an array of sources conformed on a cylindrical structure. The second lens allows deflecting a directive beam to an off-normal direction. Full-wave simulations are performed to verify the functionality of the calculated lenses. Prototypes presenting a graded refractive index are fabricated through three-dimensional polyjet printing using solely dielectric materials. Experimental measurements carried out show very good agreement with numerical simulations, thereby validating the proposed lenses. Such easily realizable designs open the way to low-cost all-dielectric microwave lenses for beam forming and collimation.

  3. 3D outflow jets originating from turbulence in the reconnection current layer

    NASA Astrophysics Data System (ADS)

    Fujimoto, Keizo

    2016-07-01

    Satellite observations in the Earth's magnetosphere and in solar flares have suggested that the reconnection outflow jets are fully three dimensional, consisting of a series of narrow channels. The jet structure is important in evaluating the energy and flux transport in the reconnection process. Previous theoretical models based on fluid simulations have relied on patchy reconnection where reconnection takes place predominantly in patchy portions of the current layer. The problem of the previous models is that the gross reconnection rate is much smaller than that in the 2D reconnection case. The present study shows a large-scale 3D PIC simulation revealing that the 3D outflow jets are generated through the 3D flux ropes formed in the turbulent electron current layer around the x-line. Reconnection proceeds almost uniformly along the x-line, so that the gross reconnection rate is comparable to that in the 2D reconnection case. The flux ropes and resultant outflow channels have a typical current-aligned scale provided by the wavelength of an electron shear mode that is much larger than the typical kinetic scales. It is found that the structure of the 3D outflow jets obtained in the simulation is consistent with the bursty bulk flow observed in the Earth's magnetotail.

  4. A 5 MHz Cylindrical Dual-Layer Transducer Array for 3-D Transrectal Ultrasound Imaging

    PubMed Central

    Chen, Yuling; Nguyen, Man; Yen, Jesse T.

    2012-01-01

    2-D transrectal ultrasound (TRUS) is being used in guiding prostate biopsies and treatments. In many cases, the TRUS probes are moved manually or mechanically to acquire volumetric information, making the imaging slow, user-dependent and unreliable. A real-time 3-D TRUS system could improve reliability and volume rates of imaging during these procedures. In this paper, we present a 5 MHz cylindrical dual-layer transducer array capable of real-time 3-D transrectal ultrasound without any mechanically moving parts. Compared to fully-sampled 2-D arrays, this design substantially reduces the channel count and fabrication complexity. This dual-layer transducer uses PZT elements for transmit and P[VDF-TrFE] copolymer elements for receive, respectively. The mechanical flexibility of both diced PZT and copolymer makes it practical for transrectal applications. Full synthetic aperture 3-D data sets were acquired by interfacing the transducer with a Verasonics Data Acquisition System (VDAS). Offline 3-D beamforming was then performed to obtain volumes of two wire phantoms and a cyst phantom. Generalized coherence factor (GCF) was applied to improve the contrast of images. The measured −6 dB fractional bandwidth of the transducer was 62% with a center frequency of 5.66 MHz. The measured lateral beamwidths were 1.28 mm and 0.91 mm in transverse and longitudinal directions respectively, compared with a simulated beamwidth of 0.92 mm and 0.74 mm. PMID:22972914

  5. Hexagonal boron nitride: Ubiquitous layered dielectric for two-dimensional electronics

    NASA Astrophysics Data System (ADS)

    Jain, Nikhil

    Hexagonal boron nitride (h-BN), a layer-structured dielectric with very similar crystalline lattice to that of graphene, has been studied as a ubiquitous dielectric for two-dimensional electronics. While 2D materials may lead to future platform for electronics, traditional thin-film dielectrics (e.g., various oxides) make highly invasive interface with graphene. Multiple key roles of h-BN in graphene electronics are explored in this thesis. 2D graphene/h-BN heterostructures are designed and implemented in diverse configurations in which h-BN is evaluated as a supporting substrate, a gate dielectric, a passivation layer, or an interposing barrier in "3D graphene" superlattice. First, CVD-grown graphene on h-BN substrate shows improved conductivity and resilience to thermally induced breakdown, as compared with graphene on SiO2, potentially useful for high-speed graphene devices and on-chip interconnects. h-BN is also explored as a gate dielectric for graphene field-effect transistor with 2D heterostructure design. The dielectric strength and tunneling behavior of h-BN are investigated, confirming its robust nature. Next, h-BN is studied as a passivation layer for graphene electronics. In addition to significant improvement in current density and breakdown threshold, fully encapsulated graphene exhibits minimal environmental sensitivity, a key benefit to 2D materials which have only surfaces. Lastly, reduction in interlayer carrier scattering is observed in a double-layered graphene setup with ultrathin h-BN multilayer as an interposing layer. The DFT simulation and Raman spectral analysis indicate reduction in interlayer scattering. The decoupling of the two graphene monolayers is further confirmed by electrical characterization, as compared with other referencing mono- and multilayer configurations. The heterostructure serves as the building element in "3D graphene", a versatile platform for future electronics.

  6. Encapsulation methods and dielectric layers for organic electrical devices

    DOEpatents

    Blum, Yigal D; Chu, William Siu-Keung; MacQueen, David Brent; Shi, Yijan

    2013-07-02

    The disclosure provides methods and materials suitable for use as encapsulation barriers and dielectric layers in electronic devices. In one embodiment, for example, there is provided an electroluminescent device or other electronic device with a dielectric layer comprising alternating layers of a silicon-containing bonding material and a ceramic material. The methods provide, for example, electronic devices with increased stability and shelf-life. The invention is useful, for example, in the field of microelectronic devices.

  7. 3D printing of layered brain-like structures using peptide modified gellan gum substrates.

    PubMed

    Lozano, Rodrigo; Stevens, Leo; Thompson, Brianna C; Gilmore, Kerry J; Gorkin, Robert; Stewart, Elise M; in het Panhuis, Marc; Romero-Ortega, Mario; Wallace, Gordon G

    2015-10-01

    The brain is an enormously complex organ structured into various regions of layered tissue. Researchers have attempted to study the brain by modeling the architecture using two dimensional (2D) in vitro cell culturing methods. While those platforms attempt to mimic the in vivo environment, they do not truly resemble the three dimensional (3D) microstructure of neuronal tissues. Development of an accurate in vitro model of the brain remains a significant obstacle to our understanding of the functioning of the brain at the tissue or organ level. To address these obstacles, we demonstrate a new method to bioprint 3D brain-like structures consisting of discrete layers of primary neural cells encapsulated in hydrogels. Brain-like structures were constructed using a bio-ink consisting of a novel peptide-modified biopolymer, gellan gum-RGD (RGD-GG), combined with primary cortical neurons. The ink was optimized for a modified reactive printing process and developed for use in traditional cell culturing facilities without the need for extensive bioprinting equipment. Furthermore the peptide modification of the gellan gum hydrogel was found to have a profound positive effect on primary cell proliferation and network formation. The neural cell viability combined with the support of neural network formation demonstrated the cell supportive nature of the matrix. The facile ability to form discrete cell-containing layers validates the application of this novel printing technique to form complex, layered and viable 3D cell structures. These brain-like structures offer the opportunity to reproduce more accurate 3D in vitro microstructures with applications ranging from cell behavior studies to improving our understanding of brain injuries and neurodegenerative diseases. PMID:26231917

  8. A Dual-Layer Transducer Array for 3-D Rectilinear Imaging

    PubMed Central

    Yen, Jesse T.; Seo, Chi Hyung; Awad, Samer I.; Jeong, Jong S.

    2010-01-01

    2-D arrays for 3-D rectilinear imaging require very large element counts (16,000–65,000). The difficulties in fabricating and interconnecting 2-D arrays with a large number of elements (>5,000) have limited the development of suitable transducers for 3-D rectilinear imaging. In this paper, we propose an alternative solution to this problem by using a dual-layer transducer array design. This design consists of two perpendicular 1-D arrays for clinical 3-D imaging of targets near the transducer. These targets include the breast, carotid artery, and musculoskeletal system. This transducer design reduces the fabrication complexity and the channel count making 3-D rectilinear imaging more realizable. With this design, an effective N × N 2-D array can be developed using only N transmitters and N receivers. This benefit becomes very significant when N becomes greater than 128, for example. To demonstrate feasibility, we constructed a 4 × 4 cm prototype dual-layer array. The transmit array uses diced PZT-5H elements, and the receive array is a single sheet of undiced P[VDF-TrFE] copolymer. The receive elements are defined by the copper traces on the flexible interconnect circuit. The measured −6 dB fractional bandwidth was 80% with a center frequency of 4.8 MHz. At 5 MHz, the nearest neighbor crosstalk of the PZT array and PVDF array was −30.4 ± 3.1 dB and −28.8 ± 3.7 dB respectively. This dual-layer transducer was interfaced with an Ultrasonix Sonix RP system, and a synthetic aperture 3-D data set was acquired. We then performed off-line 3-D beamforming to obtain volumes of nylon wire targets. The theoretical lateral beamwidth was 0.52 mm compared to measured beamwidths of 0.65 mm and 0.67 mm in azimuth and elevation respectively. 3-D images of an 8 mm diameter anechoic cyst phantom were also acquired. PMID:19213647

  9. 3D Analysis of Wake Field Excitation in a Dielectric Loaded Rectangular Resonator

    SciTech Connect

    Sotnikov, Gennadij V.; Onishchenko, Ivan N.; Marshall, Thomas C.

    2006-11-27

    The results of a three-dimensional analysis of wake field excitation in a slab-symmetric dielectric-loaded resonator by rigid electron bunches are presented. The complete set of solutions, including the solenoidal and potential parts of the electromagnetic field, consists of LSM and LSE modes. Each of the LSM and LSE modes contains odd and even waves. A numerical analysis of wake field excitation by symmetric electron bunches is carried out. The three-dimensional spatial structure of the longitudinal electric field is investigated. The influence of the drift vacuum channel on the wake field amplitude and on the coherent summation of wakefields for a regular sequence of bunches is studied.

  10. A new pillared-layer 3D coordination polymer involving in situ generated formate

    NASA Astrophysics Data System (ADS)

    Xia, Yu-Pei; Li, Yun-Wu; Li, Da-Cheng; Du, Yu-Chang; Yao, Qing-Xia; Dou, Jian-Min

    2015-02-01

    A new Cd-based coordination polymer, [Cd(cpt)(HCOO)]n (1), has been synthesized from 1-(4-carboxyphenyl)-1,2,4-triazole) ligand (Hcpt). The structure was characterized through X-ray crystallography, elemental analysis, and IR spectrum. Compound 1 presents a three-dimensional (3D) pillared-layer structure constructed by metal-formate layers and cpt- ligands. Moreover, the unusual formate anions are generated in situ from the decomposition of DMF precursors. The fluorescence property of 1 in solid state was also researched.

  11. 7.5 MHz dual-layer transducer array for 3-D rectilinear imaging.

    PubMed

    Chen, Yuling; Nguyen, Man; Yen, Jesse T

    2011-07-01

    The difficulties associated with fabrication and interconnection have limited the development of 2-D ultrasound transducer arrays with a large number ofelements (>5000). In previous work, we described a 5 MHz center frequency PZT-P[VDF-TrFE] dual-layer transducer that used two perpendicular 1-D arrays for 3-D rectilinear imaging. This design substantially reduces the channel count as well as fabrication complexity, which makes 3-D imaging more realizable. Higher frequencies (>5 MHz) are more commonly used in clinical applications or imaging targets near transducers, such as the breast, carotid and musculoskeletal tissue. In this paper, we present a 7.5 MHz dual-layer transducer array for 3-D rectilinear imaging. A modified acoustic stack model was designed and fabricated. PZT elements were sub-diced to eliminate lateral coupling. This sub-dicing process made the PZT into a 2-2 composite material, which could help improve transducer sensitivity and bandwidth. Full synthetic-aperture 3-D data sets were acquired by interfacing the transducer with a Verasonics data-acquisition system (VDAS). Offline 3-D beamforming was then performed to obtain volumes of a multiwire phantom and a cyst phantom. The generalized coherence factor (GCF) was applied to improve the contrast of cyst images. The measured -6 dB fractional bandwidth of the transducer was 71% with a center frequency of 7.5 MHz. The measured lateral beamwidths were 0.521 mm and 0.482 mm in azimuth and elevation, respectively, compared with a simulated beamwidth of 0.43 mm. PMID:21842584

  12. A 7.5 MHz Dual-Layer Transducer Array for 3-D Rectilinear Imaging

    PubMed Central

    Chen, Yuling; Nguyen, Man; Yen, Jesse T.

    2011-01-01

    The difficulties associated with fabrication and interconnection have limited the development of 2-D ultrasound transducer arrays with a large number of elements (>5000). In previous work, we described a 5 MHz center frequency PZT-P[VDF-TrFE] dual-layer transducer, which used 2 perpendicular 1-D arrays for 3-D rectilinear imaging. This design substantially reduces the channel count as well as fabrication complexity, which makes 3-D imaging more realizable. Higher frequencies (>5MHz) are more commonly used in clinical for imaging targets near transducers such as the breast, carotid, and musculoskeletal. In this paper, we present a 7.5 MHz dual-layer transducer array for 3-D rectilinear imaging. A modified acoustic stack model was designed and fabricated. PZT elements were sub-diced to eliminate lateral coupling. This sub-dicing process made the PZT into a 2–2 composite material, which could help improve transducer sensitivity and bandwidth. Full synthetic aperture 3-D data sets were acquired by interfacing the transducer with a Verasonics data acquisition system (VDAS). Offline 3-D beamforming was then performed to obtain volumes of a multi-wire phantom and a cyst phantom. The generalized coherence factor (GCF) was applied to improve the contrast of cyst images. The measured −6 dB fractional bandwidth of the transducer was 71% with a center frequency of 7.5 MHz. The measured lateral beamwidths were 0.521 mm and 0.482 mm in azimuth and elevation respectively, compared with a simulated beamwidth of 0.43 mm. PMID:21842584

  13. Effect of a 3D surface depression on boundary layer transition

    NASA Astrophysics Data System (ADS)

    Xu, Hui; Mughal, Shahid; Sherwin, Spencer J.

    2015-11-01

    The influence of a three-dimensional surface depression on the transitional boundary layer is investigated numerically. In the boundary layer transition, the primary mode is a Tollmien-Schlichting (TS) wave which is a viscous instability. These modes are receptive to surface roughness interacting with free stream disturbances and/or surface vibrations. In this paper, numerical calculations are carried out to investigate the effect of the depression on instability of the boundary layer. In order to implement linear analysis, two/three (2D/3D)-dimensional nonlinear Navier-Stokes equations are solved by spectral element method to generate base flows in a sufficient large domain. The linear analyses are done by the parabolic stability equations (PSE). Finally, a DNS calculation is done to simulate the boundary layer transition.

  14. Polymer-Based Mesh as Supports for Multi-layered 3D Cell Culture and Assays

    PubMed Central

    Simon, Karen A.; Park, Kyeng Min; Mosadegh, Bobak; Subramaniam, Anand Bala; Mazzeo, Aaron; Ngo, Phil M.; Whitesides, George M.

    2013-01-01

    Three-dimensional (3D) culture systems can mimic certain aspects of the cellular microenvironment found in vivo, but generation, analysis and imaging of current model systems for 3D cellular constructs and tissues remain challenging. This work demonstrates a 3D culture system – Cells-in-Gels-in-Mesh (CiGiM) – that uses stacked sheets of polymer-based mesh to support cells embedded in gels to form tissue-like constructs; the stacked sheets can be disassembled by peeling the sheets apart to analyze cultured cells—layer-by-layer—within the construct. The mesh sheets leave openings large enough for light to pass through with minimal scattering, and thus allowing multiple options for analysis—(i) using straightforward analysis by optical light microscopy, (ii) by high-resolution analysis with fluorescence microscopy, or (iii) with a fluorescence gel scanner. The sheets can be patterned into separate zones with paraffin film-based decals, in order to conduct multiple experiments in parallel; the paraffin-based decal films also block lateral diffusion of oxygen effectively. CiGiM simplifies the generation and analysis of 3D culture without compromising throughput, and quality of the data collected: it is especially useful in experiments that require control of oxygen levels, and isolation of adjacent wells in a multi-zone format. PMID:24095253

  15. 3D Printing of Human Tissue Mimics via Layer-by-Layer Assembly of Polymer/Hydrogel Biopapers

    NASA Astrophysics Data System (ADS)

    Ringeisen, Bradley

    2015-03-01

    The foundations of tissue engineering were built on two fundamental areas of research: cells and scaffolds. Multipotent cells and their derivatives are traditionally randomly seeded into sophisticated polymer or hydrogel scaffolds, ultimately with the goal of forming a tissue-like material through cell differentiation and cell-material interactions. One problem with this approach is that no matter how complex or biomimetic the scaffold is, the cells are still homogeneously distributed throughout this three dimensional (3D) material. Natural tissue is inherently heterogeneous on both a microscopic and macroscopic level. It also contains different types of cells in close proximity, extracellular matrix, voids, and a complex vascularized network. Recently developed 3D cell and organ printers may be able to enhance traditional tissue engineering experiments by building scaffolds layer-by-layer that are crafted to mimic the microscopic and macroscopic structure of natural tissue or organs. Over the past decade, my laboratory has developed a capillary-free, live cell printer termed biological laser printing, or BioLP. We find that printed cells do not express heat shock protein and retain >99% viability. Printed cells also incur no DNA strand fracture and preserve their ability to differentiate. Recent work has used a layer-by-layer approach, stacking sheets of hybrid polymer/hydrogel biopapers in conjunction with live cell printing to create 3D tissue structures. Our specific work is now focused on the blood-brain-barrier and air-lung interface and will be described during the presentation.

  16. Topologic connection between 2-D layered structures and 3-D diamond structures for conventional semiconductors

    NASA Astrophysics Data System (ADS)

    Wang, Jianwei; Zhang, Yong

    2016-04-01

    When coming to identify new 2D materials, our intuition would suggest us to look from layered instead of 3D materials. However, since graphite can be hypothetically derived from diamond by stretching it along its [111] axis, many 3D materials can also potentially be explored as new candidates for 2D materials. Using a density functional theory, we perform a systematic study over the common Group IV, III–V, and II–VI semiconductors along different deformation paths to reveal new structures that are topologically connected to but distinctly different from the 3D parent structure. Specifically, we explore two major phase transition paths, originating respectively from wurtzite and NiAs structure, by applying compressive and tensile strain along the symmetry axis, and calculating the total energy changes to search for potential metastable states, as well as phonon spectra to examine the structural stability. Each path is found to further split into two branches under tensile strain–low buckled and high buckled structures, which respectively lead to a low and high buckled monolayer structure. Most promising new layered or planar structures identified include BeO, GaN, and ZnO on the tensile strain side, Ge, Si, and GaP on the compressive strain side.

  17. Topologic connection between 2-D layered structures and 3-D diamond structures for conventional semiconductors

    PubMed Central

    Wang, Jianwei; Zhang, Yong

    2016-01-01

    When coming to identify new 2D materials, our intuition would suggest us to look from layered instead of 3D materials. However, since graphite can be hypothetically derived from diamond by stretching it along its [111] axis, many 3D materials can also potentially be explored as new candidates for 2D materials. Using a density functional theory, we perform a systematic study over the common Group IV, III–V, and II–VI semiconductors along different deformation paths to reveal new structures that are topologically connected to but distinctly different from the 3D parent structure. Specifically, we explore two major phase transition paths, originating respectively from wurtzite and NiAs structure, by applying compressive and tensile strain along the symmetry axis, and calculating the total energy changes to search for potential metastable states, as well as phonon spectra to examine the structural stability. Each path is found to further split into two branches under tensile strain–low buckled and high buckled structures, which respectively lead to a low and high buckled monolayer structure. Most promising new layered or planar structures identified include BeO, GaN, and ZnO on the tensile strain side, Ge, Si, and GaP on the compressive strain side. PMID:27090430

  18. Topologic connection between 2-D layered structures and 3-D diamond structures for conventional semiconductors.

    PubMed

    Wang, Jianwei; Zhang, Yong

    2016-01-01

    When coming to identify new 2D materials, our intuition would suggest us to look from layered instead of 3D materials. However, since graphite can be hypothetically derived from diamond by stretching it along its [111] axis, many 3D materials can also potentially be explored as new candidates for 2D materials. Using a density functional theory, we perform a systematic study over the common Group IV, III-V, and II-VI semiconductors along different deformation paths to reveal new structures that are topologically connected to but distinctly different from the 3D parent structure. Specifically, we explore two major phase transition paths, originating respectively from wurtzite and NiAs structure, by applying compressive and tensile strain along the symmetry axis, and calculating the total energy changes to search for potential metastable states, as well as phonon spectra to examine the structural stability. Each path is found to further split into two branches under tensile strain-low buckled and high buckled structures, which respectively lead to a low and high buckled monolayer structure. Most promising new layered or planar structures identified include BeO, GaN, and ZnO on the tensile strain side, Ge, Si, and GaP on the compressive strain side. PMID:27090430

  19. Atomically thin layered NiFe double hydroxides assembled 3D microspheres with promoted electrochemical performances

    NASA Astrophysics Data System (ADS)

    Li, Xiaomin; Zai, Jiantao; Liu, Yuanyuan; He, Xiaobo; Xiang, Shijie; Ma, Zifeng; Qian, Xuefeng

    2016-09-01

    LDHs in atomic thickness (mono-/bi-layers) usually exhibit novel physicochemical properties, especially in surface-dependent energy storage and catalysis areas. However, the thickness of the commonly reported 2D LDHs is in nanoscale and the bottom-up synthesis of atomically thin LDHs is rarely reported. Herein, high-quality atomically thin layered NiFe-LDHs assembled 3D microspheres were synthesized via a rational designed reaction system, where the formation of atomically thin building blocks was controlled by the synergetic effects of released carbonate anions and butanol. Furthermore, the complexant and solvents played important effects on the process of coprecipitation and the assembling of LDHs. Due to the nature of atomically thin LDHs nanosheets and unique 3D hierarchical structures, the obtained microspheres exhibited excellent electrocatalytic oxygen evolution reaction (OER) activity in alkaline medium with an onset overpotential (0.435 V, which is lower than that of common LDHs) and good durability. The as-prepared 3D NiFe-LDHs microspheres were also firstly used as supercapacitor materials and displayed a high specific capacitance of 1061 F g-1 at the current density of 1 A g-1.

  20. Vortex instabilities in 3D boundary layers: The relationship between Goertler and crossflow vortices

    NASA Technical Reports Server (NTRS)

    Bassom, Andrew; Hall, Philip

    1990-01-01

    The inviscid and viscous stability problems are addressed for a boundary layer which can support both Goertler and crossflow vortices. The change in structure of Goertler vortices is found when the parameter representing the degree of three-dimensionality of the basic boundary layer flow under consideration is increased. It is shown that crossflow vortices emerge naturally as this parameter is increased and ultimately become the only possible vortex instability of the flow. It is shown conclusively that at sufficiently large values of the crossflow there are no unstable Goertler vortices present in a boundary layer which, in the zero crossflow case, is centrifugally unstable. The results suggest that in many practical applications Goertler vortices cannot be a cause of transition because they are destroyed by the 3-D nature of the basic state. In swept wing flows the Goertler mechanism is probably not present for typical angles of sweep of about 20 degrees. Some discussion of the receptivity problem for vortex instabilities in weakly 3-D boundary layers is given; it is shown that inviscid modes have a coupling coefficient marginally smaller than those of the fastest growing viscous modes discussed recently by Denier, Hall, and Seddougui (1990). However the fact that the growth rates of the inviscid modes are the largest in most situations means that they are probably the most likely source of transition.

  1. Fast Numerical Algorithms for 3-D Scattering from PEC and Dielectric Random Rough Surfaces in Microwave Remote Sensing

    NASA Astrophysics Data System (ADS)

    Zhang, Lisha

    We present fast and robust numerical algorithms for 3-D scattering from perfectly electrical conducting (PEC) and dielectric random rough surfaces in microwave remote sensing. The Coifman wavelets or Coiflets are employed to implement Galerkin's procedure in the method of moments (MoM). Due to the high-precision one-point quadrature, the Coiflets yield fast evaluations of the most off-diagonal entries, reducing the matrix fill effort from O(N2) to O( N). The orthogonality and Riesz basis of the Coiflets generate well conditioned impedance matrix, with rapid convergence for the conjugate gradient solver. The resulting impedance matrix is further sparsified by the matrix-formed standard fast wavelet transform (SFWT). By properly selecting multiresolution levels of the total transformation matrix, the solution precision can be enhanced while matrix sparsity and memory consumption have not been noticeably sacrificed. The unified fast scattering algorithm for dielectric random rough surfaces can asymptotically reduce to the PEC case when the loss tangent grows extremely large. Numerical results demonstrate that the reduced PEC model does not suffer from ill-posed problems. Compared with previous publications and laboratory measurements, good agreement is observed.

  2. Using self-similarity compensation for improving inter-layer prediction in scalable 3D holoscopic video coding

    NASA Astrophysics Data System (ADS)

    Conti, Caroline; Nunes, Paulo; Ducla Soares, Luís.

    2013-09-01

    Holoscopic imaging, also known as integral imaging, has been recently attracting the attention of the research community, as a promising glassless 3D technology due to its ability to create a more realistic depth illusion than the current stereoscopic or multiview solutions. However, in order to gradually introduce this technology into the consumer market and to efficiently deliver 3D holoscopic content to end-users, backward compatibility with legacy displays is essential. Consequently, to enable 3D holoscopic content to be delivered and presented on legacy displays, a display scalable 3D holoscopic coding approach is required. Hence, this paper presents a display scalable architecture for 3D holoscopic video coding with a three-layer approach, where each layer represents a different level of display scalability: Layer 0 - a single 2D view; Layer 1 - 3D stereo or multiview; and Layer 2 - the full 3D holoscopic content. In this context, a prediction method is proposed, which combines inter-layer prediction, aiming to exploit the existing redundancy between the multiview and the 3D holoscopic layers, with self-similarity compensated prediction (previously proposed by the authors for non-scalable 3D holoscopic video coding), aiming to exploit the spatial redundancy inherent to the 3D holoscopic enhancement layer. Experimental results show that the proposed combined prediction can improve significantly the rate-distortion performance of scalable 3D holoscopic video coding with respect to the authors' previously proposed solutions, where only inter-layer or only self-similarity prediction is used.

  3. An effective 3D leapfrog scheme for electromagnetic modelling of arbitrary shaped dielectric objects using unstructured meshes

    NASA Astrophysics Data System (ADS)

    Gansen, A.; El Hachemi, M.; Belouettar, S.; Hassan, O.; Morgan, K.

    2015-12-01

    In computational electromagnetics, the advantages of the standard Yee algorithm are its simplicity and its low computational costs. However, because of the accuracy losses resulting from the staircased representation of curved interfaces, it is normally not the method of choice for modelling electromagnetic interactions with objects of arbitrary shape. For these problems, an unstructured mesh finite volume time domain method is often employed, although the scheme does not satisfy the divergence free condition at the discrete level. In this paper, we generalize the standard Yee algorithm for use on unstructured meshes and solve the problem concerning the loss of accuracy linked to staircasing, while preserving the divergence free nature of the algorithm. The scheme is implemented on high quality primal Delaunay and dual Voronoi meshes. The performance of the approach was validated in previous work by simulating the scattering of electromagnetic waves by spherical 3D PEC objects in free space. In this paper we demonstrate the performance of this scheme for penetration problems in lossy dielectrics using a new averaging technique for Delaunay and Voronoi edges at the interface. A detailed explanation of the implementation of the method, and a demonstration of the quality of the results obtained for transmittance and scattering simulations by 3D objects of arbitrary shapes, are presented.

  4. Clusters, molecular layers, and 3D crystals of water on Ni(111)

    SciTech Connect

    Thürmer, Konrad; Nie, Shu; Bartelt, Norman C.; Feibelman, Peter J.

    2014-11-14

    We examined the growth and stability of ice layers on Ni(111) up to ∼7 molecular layers (ML) thick using scanning tunneling microscopy. At low coverage, films were comprised of ∼1 nm wide two-dimensional (2D) clusters. Only above ∼0.5 ML did patches of continuous 2D layers emerge, coexisting with the clusters until the first ML was complete. The structure of the continuous layer is clearly different from that of the 2D clusters. Subsequently, a second molecular layer grew on top of the first. 3D crystallites started to form only after this 2nd ML was complete. 2D clusters re-appeared when thicker films were partially evaporated, implying that these clusters represent the equilibrium configuration at low coverage. Binding energies and image simulations computed with density functional theory suggest that the 2D clusters are partially dissociated and surrounded by H adatoms. The complete 2D layer contains only intact water molecules because of the lack of favorable binding sites for H atoms. We propose molecular structures for the 2D layer that are composed of the same pentagon-heptagon binding motif and water density observed on Pt(111). The similarity of the water structures on Pt and Ni suggests a general prescription for generating low-energy configurations on close-packed metal substrates.

  5. Multi-layer 3D imaging using a few viewpoint images and depth map

    NASA Astrophysics Data System (ADS)

    Suginohara, Hidetsugu; Sakamoto, Hirotaka; Yamanaka, Satoshi; Suyama, Shiro; Yamamoto, Hirotsugu

    2015-03-01

    In this paper, we propose a new method that makes multi-layer images from a few viewpoint images to display a 3D image by the autostereoscopic display that has multiple display screens in the depth direction. We iterate simple "Shift and Subtraction" processes to make each layer image alternately. The image made in accordance with depth map like a volume slicing by gradations is used as the initial solution of iteration process. Through the experiments using the prototype stacked two LCDs, we confirmed that it was enough to make multi-layer images from three viewpoint images to display a 3D image. Limiting the number of viewpoint images, the viewing area that allows stereoscopic view becomes narrow. To broaden the viewing area, we track the head motion of the viewer and update screen images in real time so that the viewer can maintain correct stereoscopic view within +/- 20 degrees area. In addition, we render pseudo multiple viewpoint images using depth map, then we can generate motion parallax at the same time.

  6. A homochiral 3D covalent framework assembled from vertical chiral layers with achiral bridging ligands

    NASA Astrophysics Data System (ADS)

    Wang, Xinlong; Qin, Chao; Wang, Enbo; Xu, Lin

    2005-02-01

    A novel metal-organic coordination polymer, [Cd(HPT) 2(4,4'-bpy)] n (PT=phthalate), has been hydrothermally synthesized and characterized by elemental analysis, IR, TG and single crystal X-ray diffraction. Colorless crystals crystallized in the tetragonal system, space group I4 122, a=8.294(5), b=8.294(5), c=33.7535(17) Å, V=2321.8(18) Å 3, Z=4 and R=0.0207. The structure of the compound exhibiting a homochiral 3D covalent framework based on achiral bridging ligands has been constructed by an alternating assembly of vertical chiral layers consisting of homochiral helices.

  7. Self-aligned metallization on organic semiconductor through 3D dual-layer thermal nanoimprint

    NASA Astrophysics Data System (ADS)

    Jung, Y.; Cheng, X.

    2014-09-01

    High-resolution patterning of metal structures on organic semiconductors is important to the realization of high-performance organic transistors for organic integrated circuit applications. The traditional shadow mask technique has a limited resolution, precluding sub-micron metal structures on organic semiconductors. Thus organic transistors cannot benefit from scaling into the deep sub-micron region to improve their dc and ac performances. In this work, we report an efficient multiple-level metallization on poly (3-hexylthiophene) (P3HT) with a deep sub-micron lateral gap. By using a 3D nanoimprint mold in a dual-layer thermal nanoimprint process, we achieved self-aligned two-level metallization on P3HT. The 3D dual-layer thermal nanoimprint enables the first metal patterns to have suspending side-wings that can clearly define a distance from the second metal patterns. Isotropic and anisotropic side-wing structures can be fabricated through two different schemes. The process based on isotropic side-wings achieves a lateral-gap in the order of 100 nm (scheme 1). A gap of 60 nm can be achieved from the process with anisotropic side-wings (scheme 2). Because of the capability of nanoscale metal patterning on organic semiconductors with high overlay accuracy, this self-aligned metallization technique can be utilized to fabricate high-performance organic metal semiconductor field-effect transistor.

  8. Intra-retinal layer segmentation of 3D optical coherence tomography using coarse grained diffusion map

    PubMed Central

    Kafieh, Raheleh; Rabbani, Hossein; Abramoff, Michael D.; Sonka, Milan

    2013-01-01

    Optical coherence tomography (OCT) is a powerful and noninvasive method for retinal imaging. In this paper, we introduce a fast segmentation method based on a new variant of spectral graph theory named diffusion maps. The research is performed on spectral domain (SD) OCT images depicting macular and optic nerve head appearance. The presented approach does not require edge-based image information in localizing most of boundaries and relies on regional image texture. Consequently, the proposed method demonstrates robustness in situations of low image contrast or poor layer-to-layer image gradients. Diffusion mapping applied to 2D and 3D OCT datasets is composed of two steps, one for partitioning the data into important and less important sections, and another one for localization of internal layers. In the first step, the pixels/voxels are grouped in rectangular/cubic sets to form a graph node. The weights of the graph are calculated based on geometric distances between pixels/voxels and differences of their mean intensity. The first diffusion map clusters the data into three parts, the second of which is the area of interest. The other two sections are eliminated from the remaining calculations. In the second step, the remaining area is subjected to another diffusion map assessment and the internal layers are localized based on their textural similarities. The proposed method was tested on 23 datasets from two patient groups (glaucoma and normals). The mean unsigned border positioning errors (mean ± SD) was 8.52 ± 3.13 and 7.56 ± 2.95 μm for the 2D and 3D methods, respectively. PMID:23837966

  9. Microporous polymeric 3D scaffolds templated by the layer-by-layer self-assembly.

    PubMed

    Paulraj, Thomas; Feoktistova, Natalia; Velk, Natalia; Uhlig, Katja; Duschl, Claus; Volodkin, Dmitry

    2014-08-01

    Polymeric scaffolds serve as valuable supports for biological cells since they offer essential features for guiding cellular organization and tissue development. The main challenges for scaffold fabrication are i) to tune an internal structure and ii) to load bio-molecules such as growth factors and control their local concentration and distribution. Here, a new approach for the design of hollow polymeric scaffolds using porous CaCO3 particles (cores) as templates is presented. The cores packed into a microfluidic channel are coated with polymers employing the layer-by-layer (LbL) technique. Subsequent core elimination at mild conditions results in formation of the scaffold composed of interconnected hollow polymer microspheres. The size of the cores determines the feature dimensions and, as a consequence, governs cellular adhesion: for 3T3 fibroblasts an optimal microsphere size is 12 μm. By making use of the carrier properties of the porous CaCO3 cores, the microspheres are loaded with BSA as a model protein. The scaffolds developed here may also be well suited for the localized release of bio-molecules using external triggers such as IR-light. PMID:25042776

  10. 3D quantification of microclimate volume in layered clothing for the prediction of clothing insulation.

    PubMed

    Lee, Yejin; Hong, Kyunghi; Hong, Sung-Ae

    2007-05-01

    Garment fit and resultant air volume is a crucial factor in thermal insulation, and yet, it has been difficult to quantify the air volume of clothing microclimate and relate it to the thermal insulation value just using the information on the size of clothing pattern without actual 3D volume measurement in wear condition. As earlier methods for the computation of air volume in clothing microclimate, vacuum over suit and circumference model have been used. However, these methods have inevitable disadvantages in terms of cost or accuracy due to the limitations of measurement equipment. In this paper, the phase-shifting moiré topography was introduced as one of the 3D scanning tools to measure the air volume of clothing microclimate quantitatively. The purpose of this research is to adopt a non-contact image scanning technology, phase-shifting moiré topography, to ascertain relationship between air volume and insulation value of layered clothing systems in wear situations where the 2D fabric creates new conditions in 3D spaces. The insulation of vests over shirts as a layered clothing system was measured with a thermal manikin in the environmental condition of 20 degrees C, 65% RH and air velocity of 0.79 m/s. As the pattern size increased, the insulation of the clothing system was increased. But beyond a certain limit, the insulation started to decrease due to convection and ventilation, which is more apparent when only the vest was worn over the torso of manikin. The relationship between clothing air volume and insulation was difficult to predict with a single vest due to the extreme openings which induced active ventilation. But when the vest was worn over the shirt, the effects of thickness of the fabrics on insulation were less pronounced compared with that of air volume. In conclusion, phase-shifting moiré topography was one of the efficient and accurate ways of quantifying air volume and its distribution across the clothing microclimate. It is also noted

  11. Skin-friction measurements in a 3-D, supersonic shock-wave/boundary-layer interaction

    NASA Astrophysics Data System (ADS)

    Wideman, Jeffrey Kenneth

    An experimental study has been conducted in a three-dimensional, supersonic shockwave/boundary-layer interaction (3-D SW/BLI) with the intent of providing accurate experimental data for turbulence modeling and computational fluid dynamics (CFD) code validation. The experiment was performed in the High Reynolds Channel 1 (HRCI) wind tunnel at NASA Ames Research Center. The test was conducted at a Mach number of M(sub infinity) = 2.89 and at a Reynolds number of Re = 15 x 106/m. The model consisted of a sting-supported cylinder aligned with the tunnel axis and a 20 deg half-angle conical flare offset 1.27 cm from the cylinder centerline. The generated shock system was verified to be steady by schlieren visualization. The highlight of the study was the acquisition of 3-D skin-friction data by a laser interferometric skin friction (LISF) meter. Surface pressure measurements were obtained in 15 deg intervals around the cylinder and flare. Additional measurements included surface oil flow and laser light sheet illumination which were used to document the flow topology. Skin-friction measurements are proving to be a very challenging test of a CFD code predictive capability. However, at the present time there is a very limited amount of accurate skin-friction data in complex flows such as in 3-D SW/BLI. The LISF technique is advantageous as compared to other skin-friction measurement techniques for application in complex flows like the present since it is non-intrusive and is capable of performing measurements in flows with large shear and pressure gradients where the reliability of other techniques is questionable. Thus, the prevent skin-friction data will prove valuable to turbulence modeling and CFD code validation efforts.

  12. Role of barrier layer on dielectric function of graphene double layer system at finite temperature

    NASA Astrophysics Data System (ADS)

    Patel, Digish K.; Ambavale, Sagar K.; Prajapati, Ketan; Sharma, A. C.

    2016-05-01

    We have theoretically investigated the static dielectric function of graphene double layer system (GDLS) at finite temperatures within the random phase approximation. GDLS has been suspended on a substrate and barrier layer of three different materials; h-BN, Al2O3 and HfO2 has been introduced between two graphene sheets of GDLS. We have reported dependence of the overall dielectric function of GDLS on interlayer distance and the effect of the dielectric environment at finite temperatures. Results show close relation between changing environment and behavior of dielectric constant of GDLS.

  13. Capacitance extraction from complex 3D interconnect structures

    SciTech Connect

    Cartwright, D.; Csanak, G.; George, D.; Walker, R.; Kuprat, A.; Dengi, A.; Grobman, W.

    1999-06-01

    A new tool has been developed for calculating the capacitance matrix for complex 3D interconnect structures involving multiple layers of irregularly shaped interconnect, imbedded in different dielectric materials. This method utilizes a new 3D adaptive unstructured grid capability, and a linear finite element algorithm. The capacitance is determined from the minimum in the total system energy as the nodes are varied to minimize the error in the electric field in the dielectric(s).

  14. 3-D water vapor field in the atmospheric boundary layer observed with scanning differential absorption lidar

    NASA Astrophysics Data System (ADS)

    Späth, Florian; Behrendt, Andreas; Muppa, Shravan Kumar; Metzendorf, Simon; Riede, Andrea; Wulfmeyer, Volker

    2016-04-01

    High-resolution three-dimensional (3-D) water vapor data of the atmospheric boundary layer (ABL) are required to improve our understanding of land-atmosphere exchange processes. For this purpose, the scanning differential absorption lidar (DIAL) of the University of Hohenheim (UHOH) was developed as well as new analysis tools and visualization methods. The instrument determines 3-D fields of the atmospheric water vapor number density with a temporal resolution of a few seconds and a spatial resolution of up to a few tens of meters. We present three case studies from two field campaigns. In spring 2013, the UHOH DIAL was operated within the scope of the HD(CP)2 Observational Prototype Experiment (HOPE) in western Germany. HD(CP)2 stands for High Definition of Clouds and Precipitation for advancing Climate Prediction and is a German research initiative. Range-height indicator (RHI) scans of the UHOH DIAL show the water vapor heterogeneity within a range of a few kilometers up to an altitude of 2 km and its impact on the formation of clouds at the top of the ABL. The uncertainty of the measured data was assessed for the first time by extending a technique to scanning data, which was formerly applied to vertical time series. Typically, the accuracy of the DIAL measurements is between 0.5 and 0.8 g m-3 (or < 6 %) within the ABL even during daytime. This allows for performing a RHI scan from the surface to an elevation angle of 90° within 10 min. In summer 2014, the UHOH DIAL participated in the Surface Atmosphere Boundary Layer Exchange (SABLE) campaign in southwestern Germany. Conical volume scans were made which reveal multiple water vapor layers in three dimensions. Differences in their heights in different directions can be attributed to different surface elevation. With low-elevation scans in the surface layer, the humidity profiles and gradients can be related to different land cover such as maize, grassland, and forest as well as different surface layer

  15. Turbulent boundary layer over 2D and 3D large-scale wavy walls

    NASA Astrophysics Data System (ADS)

    Chamorro, Leonardo P.; Hamed, Ali M.; Castillo, Luciano

    2015-11-01

    In this work, an experimental investigation of the developing and developed flow over two- and three-dimensional large-scale wavy walls was performed using high-resolution planar particle image velocimetry in a refractive-index-matching flume. The 2D wall is described by a sinusoidal wave in the streamwise direction with amplitude to wavelength ratio a/ λx = 0.05. The 3D wall is defined with an additional wave superimposed on the 2D wall in the spanwise direction with a/ λy = 0.1. The flow was characterized at Reynolds numbers of 4000 and 40000, based on the bulk velocity and the flume half height. Instantaneous velocity fields and time-averaged turbulence quantities reveal strong coupling between large-scale topography and the turbulence dynamics near the wall. Turbulence statistics show the presence of a well-structured shear layer that enhances the turbulence for the 2D wavy wall, whereas the 3D wall exhibits different flow dynamics and significantly lower turbulence levels, particularly for which shows about 30% reduction. The likelihood of recirculation bubbles, levels and spatial distribution of turbulence, and the rate of the turbulent kinetic energy production are shown to be severely affected when a single spanwise mode is superimposed on the 2D wall. POD analysis was also performed to further understand distinctive features of the flow structures due to surface topography.

  16. Development of a dual layered dielectric-loaded accelerating structure.

    SciTech Connect

    Gai, W.; Liu, W.; Jing, C.; Kanareykin, A.; Antipov, S.; Nenasheva, E.; Schoessow, P.; High Energy Physics; Euclid Techlabs, LLC; Illinois Inst. of Tech.; KEK

    2008-09-01

    Due to the high magnetic field-induced surface currents on its conducting sleeve, a conventional single layer Dielectric-Loaded Accelerating (DLA) structure exhibits a relatively high RF loss. One possible way to solve this problem is to use multilayered DLA structures. In these devices, the RF power attenuation is reduced by making use of the Bragg Fiber concept: the EM fields are well confined by multiple reflections from multiple dielectric layers. This paper presents the design of an X-band dual layer DLA structure as well as the results of bench tests of the device. We will also present results on the design, numerical modeling, and fabrication of structures for coupling RF into multilayer DLAs such as a novel TM{sub 03} mode launcher and a TM{sub 01}-TM{sub 03} mode converter using dielectric-loaded corrugated waveguide.

  17. Experimentally excellent beaming in a two-layer dielectric structure

    SciTech Connect

    Tasolamprou, Anna C.; Zhang, Lei; Kafesaki, Maria; Koschny, Thomas; Soukoulis, Costas M.

    2014-09-15

    We demonstrate both experimentally and theoretically that a two-layer dielectric structure can provide collimation and enhanced transmission of a Gaussian beam passing through it. This is due to formation of surface localized states along the layered structure and the coupling of these states to outgoing propagating waves. As a result, a system of multiple cascading two-layers can sustain the beaming for large propagation distances.

  18. Experimental Investigation of the Near Wall Flow Structure of a Low Reynolds Number 3-D Turbulent Boundary Layer

    NASA Technical Reports Server (NTRS)

    Fleming, J. L.; Simpson, R. L.

    1997-01-01

    Laser Doppler velocimetry (LDV) measurements and hydrogen bubble flow visualization techniques were used to examine the near-wall flow structure of 2D and 3D turbulent boundary layers (TBLs) over a range of low Reynolds numbers. The goals of this research were (1) an increased understanding of the flow physics in the near wall region of turbulent boundary layers,(2) to observe and quantify differences between 2D and 3D TBL flow structures, and (3) to document Reynolds number effects for 3D TBLs. The LDV data have provided results detailing the turbulence structure of the 2D and 3D TBLs. These results include mean Reynolds stress distributions, flow skewing results, and U and V spectra. Effects of Reynolds number for the 3D flow were also examined. Comparison to results with the same 3D flow geometry but at a significantly higher Reynolds number provided unique insight into the structure of 3D TBLs. While the 3D mean and fluctuating velocities were found to be highly dependent on Reynolds number, a previously defined shear stress parameter was discovered to be invariant with Reynolds number. The hydrogen bubble technique was used as a flow visualization tool to examine the near-wall flow structure of 2D and 3D TBLs. Both the quantitative and qualitative results displayed larger turbulent fluctuations with more highly concentrated vorticity regions for the 2D flow.

  19. Layer-by-layer assembly of antibacterial coating on interbonded 3D fibrous scaffolds and its cytocompatibility assessment.

    PubMed

    Tang, Yanwei; Zhao, Yan; Wang, Hongxia; Gao, Yuan; Liu, Xin; Wang, Xungai; Lin, Tong

    2012-08-01

    Bonded fibrous matrices have shown great potential in tissue engineering because of their unique 3D structures and pore characteristics. For some applications, bacterial infections must be taken into account, and antibacterial function is highly desired. In this study, an antibacterial polymer, polyhexamethylene biguanide (PHMB), was applied onto the fiber surface of a bonded poly(ε-caprolactone) (PCL) fibrous matrix with the objective to achieve both strong antibacterial effect and good cell compatibility. The coatings were prepared by using an electrostatic layer-by-layer (LbL) assembly technique, which allowed the control of PHMB loading and coating uniformity on the fiber surface. The PHMB coating provided antibacterial activities, but had no toxicity on mammalian cells. This bonded PCL fibrous matrix with electrostatically self-assembled PHMB may provide a new antiinfective tissue scaffold for various biomedical applications. PMID:22581705

  20. Electric double layer of anisotropic dielectric colloids under electric fields

    NASA Astrophysics Data System (ADS)

    Han, M.; Wu, H.; Luijten, E.

    2016-07-01

    Anisotropic colloidal particles constitute an important class of building blocks for self-assembly directed by electrical fields. The aggregation of these building blocks is driven by induced dipole moments, which arise from an interplay between dielectric effects and the electric double layer. For particles that are anisotropic in shape, charge distribution, and dielectric properties, calculation of the electric double layer requires coupling of the ionic dynamics to a Poisson solver. We apply recently proposed methods to solve this problem for experimentally employed colloids in static and time-dependent electric fields. This allows us to predict the effects of field strength and frequency on the colloidal properties.

  1. 3D Dynamics of Freshwater Lenses in the Near-Surface Layer of the Tropical Ocean

    NASA Astrophysics Data System (ADS)

    Soloviev, Alexander; Dean, Cayla

    2015-04-01

    Convective rains in the Intertropical Convergence Zone (ITCZ) produce lenses of freshened water on the ocean surface. These lenses are localized in space and typically involve both salinity and temperature anomalies. Due to significant density anomalies, strong pressure gradients develop, which result in lateral spreading of freshwater lenses in a form resembling gravity currents. Gravity currents inherently involve three-dimensional dynamics. As a type of organized structure, gravity currents in the upper layer of the ocean may also interact with, and be shaped by, the ambient oceanic environment and atmospheric conditions. Among the important factors are the background stratification, wind stress, wind/wave mixing and spatially coherent organized motions in the near-surface layer of the ocean. Under certain conditions, a resonant interaction between a propagating freshwater lens and internal waves in the underlying pycnocline (e.g., barrier layer) may develop, whereas interaction with wind stress may produce an asymmetry in the freshwater lens and associated mixing. These two types of interactions working in concert may explain the series of sharp frontal interfaces, which have been observed in association with freshwater lenses during TOGA COARE. In this work, we have conducted a series of numerical experiments using computational fluid dynamics tools. These numerical simulations were designed to elucidate the relationship between vertical mixing and horizontal advection of salinity under various environmental conditions and potential impact on the Aquarius and SMOS satellite image formation. Available near-surface data from field experiments served as a guidance for numerical simulations. The results of this study indicate that 3D dynamics of freshwater lenses are essential within a certain range of wind/wave conditions and the freshwater influx in the surface layer of the ocean.

  2. Number of Dielectric Layers Dependence of Dielectric Properties and Residual Stress of Multilayer Ceramic Capacitors with Ni Electrodes

    NASA Astrophysics Data System (ADS)

    Nakano, Yukie; Nomura, Takeshi; Takenaka, Tadashi

    2004-08-01

    The relationship between the residual stress and dielectric properties of multilayer ceramic capacitors with Ni electrodes (Ni-MLCCs) has been studied. Residual stress measurement by X-ray diffraction revealed that tensile stress inside MLCCs in the thickness direction increased with increasing number of dielectric layers. The increase in the ratio of the c-axis to the a-axis of BaTiO3 in the thickness direction of MLCCs was expected from the results of X-ray diffraction with increasing number of dielectric layers. The increase in dielectric constant and its temperature dependence with increasing number of dielectric layers were expectedly related to crystal structures.

  3. Full Waveform 3D Synthetic Seismic Algorithm for 1D Layered Anelastic Models

    NASA Astrophysics Data System (ADS)

    Schwaiger, H. F.; Aldridge, D. F.; Haney, M. M.

    2007-12-01

    Numerical calculation of synthetic seismograms for 1D layered earth models remains a significant aspect of amplitude-offset investigations, surface wave studies, microseismic event location approaches, and reflection interpretation or inversion processes. Compared to 3D finite-difference algorithms, memory demand and execution time are greatly reduced, enabling rapid generation of seismic data within workstation or laptop computational environments. We have developed a frequency-wavenumber forward modeling algorithm adapted to realistic 1D geologic media, for the purpose of calculating seismograms accurately and efficiently. The earth model consists of N layers bounded by two halfspaces. Each layer/halfspace is a homogeneous and isotropic anelastic (attenuative and dispersive) solid, characterized by a rectangular relaxation spectrum of absorption mechanisms. Compressional and shear phase speeds and quality factors are specified at a particular reference frequency. Solution methodology involves 3D Fourier transforming the three coupled, second- order, integro-differential equations for particle displacements to the frequency-horizontal wavenumber domain. An analytic solution of the resulting ordinary differential system is obtained. Imposition of welded interface conditions (continuity of displacement and stress) at all interfaces, as well as radiation conditions in the two halfspaces, yields a system of 6(N+1) linear algebraic equations for the coefficients in the ODE solution. An optimized inverse 2D Fourier transform to the space domain gives the seismic wavefield on a horizontal plane. Finally, three-component seismograms are obtained by accumulating frequency spectra at designated receiver positions on this plane, followed by a 1D inverse FFT from angular frequency ω to time. Stress-free conditions may be applied at the top or bottom interfaces, and seismic waves are initiated by force or moment density sources. Examples reveal that including attenuation

  4. Mechanism Underlying Stacking-Layer Effect of Dielectric Properties of Multilayer Ceramic Capacitors

    NASA Astrophysics Data System (ADS)

    Yokomizo, Satoshi; Hoshina, Takuya; Takeda, Hiroaki; Taniguchi, Katsuya; Mizuno, Youichi; Chazono, Hirokazu; Tsurumi, Takaaki

    2010-04-01

    The stacking-layer effect in multilayer ceramic capacitors (MLCCs) is a phenomenon in which the dielectric permittivity of dielectric layers increases with increasing number of layers. To elucidate the mechanism underlying this effect, we performed a simulation of residual stress in MLCCs by the finite element method (FEM) as well as dielectric measurements under uniaxial compressive stress. The FEM analysis revealed that tensile stress along the stacking direction was induced in dielectric layers owing to the difference in thermal expansion coefficient between internal electrodes and dielectric layers. The results of dielectric measurements indicated that the shell part in the dielectrics of MLCCs played an important role in the stress dependence of dielectric properties. The mechanism underlying the stacking-layer effect proposed in this study was based on the enhancement of polarization rotations in polar nanoregions in the relaxor by the tensile stress in dielectric layers.

  5. Advanced optical interference filters based on metal and dielectric layers.

    PubMed

    Begou, Thomas; Lemarchand, Fabien; Lumeau, Julien

    2016-09-01

    In this paper, we investigate the design and the fabrication of an advanced optical interference filter based on metal and dielectric layers. This filter respects the specifications of the 2016 OIC manufacturing problem contest. We study and present all the challenges and solutions that allowed achieving a low deviation between the fabricated prototype and the target. PMID:27607695

  6. Data-driven layer-stripping strategy in 3-D joint refraction and reflection travel-time tomography with TOMO3D

    NASA Astrophysics Data System (ADS)

    Meléndez, Adrià; Korenaga, Jun; Sallarès, Valentí; Miniussi, Alain; Ranero, César

    2015-04-01

    We present a new 3-D travel-time tomography code (TOMO3D) for the modelling of active-source seismic data that uses the arrival times of both refracted and reflected seismic phases to derive the propagation velocity distribution and the geometry of reflecting boundaries in the subsurface. The combination of refracted and reflected data provides a denser coverage of the study area. Moreover, because refractions only depend on the velocity parameters, they contribute to the mitigation of the negative effect of the ambiguity between layer thickness and propagation velocity that is intrinsic to the reflections that define these boundaries. This code is based on its renowned 2-D version TOMO2D from which it inherited the methods to solve the forward and inverse problems. The forward travel-time calculations are conducted using a hybrid ray-tracing technique combining the graph or shortest path method and the bending method. The LSQR algorithm is used to perform the iterative inversion of travel-time residuals to update the initial velocity and depth models. In order to cope with the increased computational demand due to the incorporation of the third dimension, the forward problem solver, which takes by far most of the run time (~90%), has been parallelised with a combination of MP and MPI standards. This parallelisation distributes the ray-tracing and travel-time calculations among the available computational resources, allowing the user to set the number of nodes, processors and cores to be used. The code's performance was evaluated with a complex synthetic case simulating a subduction zone. The objective is to retrieve the velocity distribution of both upper and lower plates and the geometry of the interplate and Moho boundaries. Our tomography method is designed to deal with a single reflector per inversion, and we show that a data-driven layer-stripping strategy allows to successfully recover several reflectors in successive inversions. This strategy consists in

  7. Data-driven inversion of 3D GPR data for layered media

    NASA Astrophysics Data System (ADS)

    Slob, E. C.

    2013-12-01

    The number of GPR applications is large and still increasing. In several applications fixed-offset measurements can be sufficient and many dedicated imaging and inversion methods have been developed. Because there is insufficient amounts of data, these are necessarily model-driven schemes. For problems where quantitative information is needed, usually it is better to record multi-offset and possibly multicomponent data. Even for this data inversion is usually model-driven. This means the inverse problem is formulated as an iterative forward modeling problem and is solved by minimizing the amplitude difference between modeled and measured data. The model is modified such that data computed from the model fits the measured data. The information in the measured data itself is not used, except as a measure of the model data fit. For multi-offset multicomponent data a data-driven scheme is here developed to perform full waveform inversion of 3D ground-penetrating radar reflection data acquired on the surface of a layered medium. For data-driven models to work well, the data has to be properly sampled. The advantage is that no model information is necessary to carry out the inversion. The inversion is carried out in three steps. First the data is decomposed into up- and downgoing wave modes. In a layered earth the two modes are separable and are treated separately. This step provides the reflection response of the layered medium. For 3D waves in a layered medium this requires knowledge of the horizontal electric and magnetic field components. If the data is properly sampled the solution is unique. The second step consists of wave field synthesis, where the reflection response is used to construct a focusing wave field that can focus in a virtual receiver position at any depth level. At this stage of the process the depth level is only known in terms of one-way travel time. This is the intercept time in the slowness domain obtained directly from the data. A virtual

  8. High-resolution imaging and inversion of 3D GPR data for layered media

    NASA Astrophysics Data System (ADS)

    Slob, Evert

    2013-04-01

    Ground penetrating radar is increasingly being used to provide quantitative information of layered structures. For application in civil engineering these can be roads, highway pavements, airport runways, bridges, tunnels, or buildings. Monitoring is important for the management and safety of these structures. Standard imaging uses a modeled wavefield extrapolator to image the data and the quality of the image depends heavily on the quality of the modeled extrapolator. Usually, data inversion is implemented by minimizing a cost function involving the measured data and the modeled data. The model is modified such that data computed from the model fits to the measured data. The data itself is not used, except as a measure of the model data fit. A recently developed alternative method is to use results from inverse scattering theory to first construct an image while all multiple reflections are simultaneously eliminated from the data. This image can be constructed from surface reflection data if the data allows separating the subsurface reflection response from the down going emitted field. For 3D waves in a layered medium this requires knowledge of all horizontal electric and magnetic field components. If the data is properly sampled the solution is unique. In layered media the plane wave decomposition allows computing the image for each angle of incidence separately as a function of image time that is equal to the one-way intercept time. Once the image is constructed for all available angles of incidence a simple matrix inversion leads to the desired electric permittivity and magnetic permeability values in each layer. Finally these values provide interval velocities that can be used to convert image time to depth and the inverse problem is solved. The theory requires infinite bandwidth frequency domain data, which is equivalent to measuring the true impulse response. This is not possible in practice and numerical results show that data with finite bandwidths can be

  9. Multigrid direct numerical simulation of the whole process of flow transition in 3-D boundary layers

    NASA Technical Reports Server (NTRS)

    Liu, Chaoqun; Liu, Zhining

    1993-01-01

    A new technology was developed in this study which provides a successful numerical simulation of the whole process of flow transition in 3-D boundary layers, including linear growth, secondary instability, breakdown, and transition at relatively low CPU cost. Most other spatial numerical simulations require high CPU cost and blow up at the stage of flow breakdown. A fourth-order finite difference scheme on stretched and staggered grids, a fully implicit time marching technique, a semi-coarsening multigrid based on the so-called approximate line-box relaxation, and a buffer domain for the outflow boundary conditions were all used for high-order accuracy, good stability, and fast convergence. A new fine-coarse-fine grid mapping technique was developed to keep the code running after the laminar flow breaks down. The computational results are in good agreement with linear stability theory, secondary instability theory, and some experiments. The cost for a typical case with 162 x 34 x 34 grid is around 2 CRAY-YMP CPU hours for 10 T-S periods.

  10. Dielectric and Conductivity Mapping of Few-Layer Metal Chalcogenides

    NASA Astrophysics Data System (ADS)

    Lai, Keji; Wu, Di; Liu, Yingnan; Ren, Yuan; Lin, Min; Peng, Hailin; Ismach, Ariel; Ghosh, Rudresh; Ruoff, Rodney

    2014-03-01

    A novel microwave impedance microscope was used to spatially map the local dielectric constant and conductivity of few-layered metal chalcogenides without the need of contact electrodes. For phase-change In2Se3 nanoplates grown on mica substrates, our results showed a sudden drop of permittivity from the bulk value for thicknesses below 5 layers and strong dielectric inhomogeneity around 4 and 5 layers. For CVD-grown MoS2 flakes on SiO2/Si wafers, we observed highly conductive localized regions within monolayer islands. These regions, which can be imaged by scanning electron microscopy and atomic force microscopy, show enhanced Raman signals and PL signal quenching. Continued imaging effort is expected to shed some light on the growth mechanism and electron physics of these quasi-2D chalcogenides.

  11. Pushing the Limits: 3D Layer-by-Layer-Assembled Composites for Cathodes with 160 C Discharge Rates.

    PubMed

    Mo, Runwei; Tung, Siu On; Lei, Zhengyu; Zhao, Guangyu; Sun, Kening; Kotov, Nicholas A

    2015-05-26

    Deficiencies of cathode materials severely limit cycling performance and discharge rates of Li batteries. The key problem is that cathode materials must combine multiple properties: high lithium ion intercalation capacity, electrical/ionic conductivity, porosity, and mechanical toughness. Some materials revealed promising characteristics in a subset of these properties, but attaining the entire set of often contrarian characteristics requires new methods of materials engineering. In this paper, we report high surface area 3D composite from reduced graphene oxide loaded with LiFePO4 (LFP) nanoparticles made by layer-by-layer assembly (LBL). High electrical conductivity of the LBL composite is combined with high ionic conductivity, toughness, and low impedance. As a result of such materials properties, reversible lithium storage capacity and Coulombic efficiency were as high as 148 mA h g(-1) and 99%, respectively, after 100 cycles at 1 C. Moreover, these composites enabled unusually high reversible charge-discharge rates up to 160 C with a storage capacity of 56 mA h g(-1), exceeding those of known LFP-based cathodes, some of them by several times while retaining high content of active cathode material. The study demonstrates that LBL-assembled composites enable resolution of difficult materials engineering tasks. PMID:25910177

  12. Estimation of uncertainties in geological 3D raster layer models as integral part of modelling procedures

    NASA Astrophysics Data System (ADS)

    Maljers, Denise; den Dulk, Maryke; ten Veen, Johan; Hummelman, Jan; Gunnink, Jan; van Gessel, Serge

    2016-04-01

    The Geological Survey of the Netherlands (GSN) develops and maintains subsurface models with regional to national coverage. These models are paramount for petroleum exploration in conventional reservoirs, for understanding the distribution of unconventional reservoirs, for mapping geothermal aquifers, for the potential to store carbon, or for groundwater- or aggregate resources. Depending on the application domain these models differ in depth range, scale, data used, modelling software and modelling technique. Depth uncertainty information is available for the Geological Survey's 3D raster layer models DGM Deep and DGM Shallow. These models cover different depth intervals and are constructed using different data types and different modelling software. Quantifying the uncertainty of geological models that are constructed using multiple data types as well as geological expert-knowledge is not straightforward. Examples of geological expert-knowledge are trend surfaces displaying the regional thickness trends of basin fills or steering points that are used to guide the pinching out of geological formations or the modelling of the complex stratal geometries associated with saltdomes and saltridges. This added a-priori knowledge, combined with the assumptions underlying kriging (normality and second-order stationarity), makes the kriging standard error an incorrect measure of uncertainty for our geological models. Therefore the methods described below were developed. For the DGM Deep model a workflow has been developed to assess uncertainty by combining precision (giving information on the reproducibility of the model results) and accuracy (reflecting the proximity of estimates to the true value). This was achieved by centering the resulting standard deviations around well-tied depths surfaces. The standard deviations are subsequently modified by three other possible error sources: data error, structural complexity and velocity model error. The uncertainty workflow

  13. Electrical conduction mechanisms in PbSe and PbS nano crystals 3D matrix layer

    NASA Astrophysics Data System (ADS)

    Arbell, Matan; Hechster, Elad; Sarusi, Gabby

    2016-02-01

    A simulation study and measurements of the electrical conductance in a PbSe and PbS spherical Nano-crystal 3D matrix layer was carried out focusing on its dependences of Nano-crystal size distribution and size gradient along the layer thickness (z-direction). The study suggests a new concept of conductance enhancement by utilizing a size gradient along the layer thickness from mono-layer to the next mono-layer of the Nano-crystals, in order to create a gradient of the energy levels and thus improve directional conductance in this direction. A Monte Carlo simulation of the charge carriers path along the layer thickness of the Nano-crystals 3D matrix using the Miller-Abrahams hopping model was performed. We then compared the conductance characteristics of the gradual size 3D matrix layer to a constant-sized 3D matrix layer that was used as a reference in the simulation. The numerical calculations provided us with insights into the actual conductance mechanism of the PbSe and PbS Nano-crystals 3D matrix and explained the discrepancies in actual conductance and the variability in measured mobilities published in the literature. It is found that the mobility and thus conductance are dependent on a critical electrical field generated between two adjacent nano-crystals. Our model explains the conductance dependents on the: Cathode-Anode distance, the distance between the adjacent nano-crystals in the 3D matrix layer and the size distribution along the current direction. Part of the model (current-voltage dependence) was validated using a current-voltage measurements taken on a constant size normal distribution nano-crystals PbS layer (330nm thick) compared with the predicted I-V curves. It is shown that under a threshold bias, the current is very low, while after above a threshold bias the conductance is significantly increased due to increase of hopping probability. Once reaching the maximum probability the current tend to level-off reaching the maximal conductance

  14. Characterizing microscale aluminum composite layer properties on silicon solar cells with hybrid 3D scanning force measurements

    PubMed Central

    Bae, Sung-Kuk; Choi, Beomjoon; Chung, Haseung; Shin, Seungwon; Song, Hee-eun; Seo, Jung Hwan

    2016-01-01

    This article presents a novel technique to estimate the mechanical properties of the aluminum composite layer on silicon solar cells by using a hybrid 3-dimensional laser scanning force measurement (3-D LSFM) system. The 3-D LSFM system measures the material properties of sub-layers constituting a solar cell. This measurement is critical for realizing high-efficient ultra-thin solar cells. The screen-printed aluminum layer, which significantly affects the bowing phenomenon, is separated from the complete solar cell by removing the silicon (Si) layer with deep reactive ion etching. An elastic modulus of ~15.1 GPa and a yield strength of ~35.0 MPa for the aluminum (Al) composite layer were obtained by the 3-D LSFM system. In experiments performed for 6-inch Si solar cells, the bowing distances decreased from 12.02 to 1.18 mm while the Si layer thicknesses increased from 90 to 190 μm. These results are in excellent agreement with the theoretical predictions for ultra-thin Si thickness (90 μm) based on the obtained Al composite layer properties. PMID:26948248

  15. Characterizing microscale aluminum composite layer properties on silicon solar cells with hybrid 3D scanning force measurements

    NASA Astrophysics Data System (ADS)

    Bae, Sung-Kuk; Choi, Beomjoon; Chung, Haseung; Shin, Seungwon; Song, Hee-Eun; Seo, Jung Hwan

    2016-03-01

    This article presents a novel technique to estimate the mechanical properties of the aluminum composite layer on silicon solar cells by using a hybrid 3-dimensional laser scanning force measurement (3-D LSFM) system. The 3-D LSFM system measures the material properties of sub-layers constituting a solar cell. This measurement is critical for realizing high-efficient ultra-thin solar cells. The screen-printed aluminum layer, which significantly affects the bowing phenomenon, is separated from the complete solar cell by removing the silicon (Si) layer with deep reactive ion etching. An elastic modulus of ~15.1 GPa and a yield strength of ~35.0 MPa for the aluminum (Al) composite layer were obtained by the 3-D LSFM system. In experiments performed for 6-inch Si solar cells, the bowing distances decreased from 12.02 to 1.18 mm while the Si layer thicknesses increased from 90 to 190 μm. These results are in excellent agreement with the theoretical predictions for ultra-thin Si thickness (90 μm) based on the obtained Al composite layer properties.

  16. Characterizing microscale aluminum composite layer properties on silicon solar cells with hybrid 3D scanning force measurements.

    PubMed

    Bae, Sung-Kuk; Choi, Beomjoon; Chung, Haseung; Shin, Seungwon; Song, Hee-Eun; Seo, Jung Hwan

    2016-01-01

    This article presents a novel technique to estimate the mechanical properties of the aluminum composite layer on silicon solar cells by using a hybrid 3-dimensional laser scanning force measurement (3-D LSFM) system. The 3-D LSFM system measures the material properties of sub-layers constituting a solar cell. This measurement is critical for realizing high-efficient ultra-thin solar cells. The screen-printed aluminum layer, which significantly affects the bowing phenomenon, is separated from the complete solar cell by removing the silicon (Si) layer with deep reactive ion etching. An elastic modulus of ~15.1 GPa and a yield strength of ~35.0 MPa for the aluminum (Al) composite layer were obtained by the 3-D LSFM system. In experiments performed for 6-inch Si solar cells, the bowing distances decreased from 12.02 to 1.18 mm while the Si layer thicknesses increased from 90 to 190 μm. These results are in excellent agreement with the theoretical predictions for ultra-thin Si thickness (90 μm) based on the obtained Al composite layer properties. PMID:26948248

  17. A second-order 3D electromagnetics algorithm for curved interfaces between anisotropic dielectrics on a Yee mesh

    SciTech Connect

    Bauer, Carl A.; Werner, Gregory R.; Cary, John R.

    2011-03-01

    A new frequency-domain electromagnetics algorithm is developed for simulating curved interfaces between anisotropic dielectrics embedded in a Yee mesh with second-order error in resonant frequencies. The algorithm is systematically derived using the finite integration formulation of Maxwell's equations on the Yee mesh. Second-order convergence of the error in resonant frequencies is achieved by guaranteeing first-order error on dielectric boundaries and second-order error in bulk (possibly anisotropic) regions. Convergence studies, conducted for an analytically solvable problem and for a photonic crystal of ellipsoids with anisotropic dielectric constant, both show second-order convergence of frequency error; the convergence is sufficiently smooth that Richardson extrapolation yields roughly third-order convergence. The convergence of electric fields near the dielectric interface for the analytic problem is also presented.

  18. Analysis of thin baked-on silicone layers by FTIR and 3D-Laser Scanning Microscopy.

    PubMed

    Funke, Stefanie; Matilainen, Julia; Nalenz, Heiko; Bechtold-Peters, Karoline; Mahler, Hanns-Christian; Friess, Wolfgang

    2015-10-01

    Pre-filled syringes (PFS) and auto-injection devices with cartridges are increasingly used for parenteral administration. To assure functionality, silicone oil is applied to the inner surface of the glass barrel. Silicone oil migration into the product can be minimized by applying a thin but sufficient layer of silicone oil emulsion followed by thermal bake-on versus spraying-on silicone oil. Silicone layers thicker than 100nm resulting from regular spray-on siliconization can be characterized using interferometric profilometers. However, the analysis of thin silicone layers generated by bake-on siliconization is more challenging. In this paper, we have evaluated Fourier transform infrared (FTIR) spectroscopy after solvent extraction and a new 3D-Laser Scanning Microscopy (3D-LSM) to overcome this challenge. A multi-step solvent extraction and subsequent FTIR spectroscopy enabled to quantify baked-on silicone levels as low as 21-325μg per 5mL cartridge. 3D-LSM was successfully established to visualize and measure baked-on silicone layers as thin as 10nm. 3D-LSM was additionally used to analyze the silicone oil distribution within cartridges at such low levels. Both methods provided new, highly valuable insights to characterize the siliconization after processing, in order to achieve functionality. PMID:26316044

  19. 3D homogeneity study in PMMA layers using a Fourier domain OCT system

    NASA Astrophysics Data System (ADS)

    Briones-R., Manuel de J.; Torre-Ibarra, Manuel H. De La; Tavera, Cesar G.; Luna H., Juan M.; Mendoza-Santoyo, Fernando

    2016-11-01

    Micro-metallic particles embedded in polymers are now widely used in several industrial applications in order to modify the mechanical properties of the bulk. A uniform distribution of these particles inside the polymers is highly desired for instance, when a biological backscattering is simulated or a bio-framework is designed. A 3D Fourier domain optical coherence tomography system to detect the polymer's internal homogeneity is proposed. This optical system has a 2D camera sensor array that records a fringe pattern used to reconstruct with a single shot the tomographic image of the sample. The system gathers the full 3D tomographic and optical phase information during a controlled deformation by means of a motion linear stage. This stage avoids the use of expensive tilting stages, which in addition are commonly controlled by piezo drivers. As proof of principle, a series of different deformations were proposed to detect the uniform or non-uniform internal deposition of copper micro particles. The results are presented as images coming from the 3D tomographic micro reconstruction of the samples, and the 3D optical phase information that identifies the in-homogeneity regions within the Poly methyl methacrylate (PMMA) volume.

  20. Dielectric function for doped graphene layer with barium titanate

    NASA Astrophysics Data System (ADS)

    Martinez Ramos, Manuel; Garces Garcia, Eric; Magana, Fernado; Vazquez Fonseca, Gerardo Jorge

    2015-03-01

    The aim of our study is to calculate the dielectric function for a system formed with a graphene layer doped with barium titanate. Density functional theory, within the local density approximation, plane-waves and pseudopotentials scheme as implemented in Quantum Espresso suite of programs was used. We considered 128 carbon atoms with a barium titanate cluster of 11 molecules as unit cell with periodic conditions. The geometry optimization is achieved. Optimization of structural configuration is performed by relaxation of all atomic positions to minimize their total energies. Band structure, density of states and linear optical response (the imaginary part of dielectric tensor) were calculated. We thank Dirección General de Asuntos del Personal Académico de la Universidad Nacional Autónoma de México, partial financial support by Grant IN-106514 and we also thank Miztli Super-Computing center the technical assistance.

  1. Layer-by-Layer Assembled 2D Montmorillonite Dielectrics for Solution-Processed Electronics.

    PubMed

    Zhu, Jian; Liu, Xiaolong; Geier, Michael L; McMorrow, Julian J; Jariwala, Deep; Beck, Megan E; Huang, Wei; Marks, Tobin J; Hersam, Mark C

    2016-01-01

    Layer-by-layer assembled 2D montmorillonite nanosheets are shown to be high-performance, solution-processed dielectrics. These scalable and spatially uniform sub-10 nm thick dielectrics yield high areal capacitances of ≈600 nF cm(-2) and low leakage currents down to 6 × 10(-9) A cm(-2) that enable low voltage operation of p-type semiconducting single-walled carbon nanotube and n-type indium gallium zinc oxide field-effect transistors. PMID:26514248

  2. Estimating 3D variation in active-layer thickness beneath arctic streams using ground-penetrating radar

    USGS Publications Warehouse

    Brosten, T.R.; Bradford, J.H.; McNamara, J.P.; Gooseff, M.N.; Zarnetske, J.P.; Bowden, W.B.; Johnston, M.E.

    2009-01-01

    We acquired three-dimensional (3D) ground-penetrating radar (GPR) data across three stream sites on the North Slope, AK, in August 2005, to investigate the dependence of thaw depth on channel morphology. Data were migrated with mean velocities derived from multi-offset GPR profiles collected across a stream section within each of the 3D survey areas. GPR data interpretations from the alluvial-lined stream site illustrate greater thaw depths beneath riffle and gravel bar features relative to neighboring pool features. The peat-lined stream sites indicate the opposite; greater thaw depths beneath pools and shallower thaw beneath the connecting runs. Results provide detailed 3D geometry of active-layer thaw depths that can support hydrological studies seeking to quantify transport and biogeochemical processes that occur within the hyporheic zone.

  3. Implementation of wall boundary conditions for transpiration in F3D thin-layer Navier-Stokes code

    NASA Technical Reports Server (NTRS)

    Kandula, M.; Martin, F. W., Jr.

    1991-01-01

    Numerical boundary conditions for mass injection/suction at the wall are incorporated in the thin-layer Navier-Stokes code, F3D. The accuracy of the boundary conditions and the code is assessed by a detailed comparison of the predictions of velocity distributions and skin-friction coefficients with exact similarity solutions for laminar flow over a flat plate with variable blowing/suction, and measurements for turbulent flow past a flat plate with uniform blowing. In laminar flow, F3D predictions for friction coefficient compare well with exact similarity solution with and without suction, but produces large errors at moderate-to-large values of blowing. A slight Mach number dependence of skin-friction coefficient due to blowing in turbulent flow is computed by F3D code. Predicted surface pressures for turbulent flow past an airfoil with mass injection are in qualitative agreement with measurements for a flat plate.

  4. Damage evaluation in graphene underlying atomic layer deposition dielectrics

    PubMed Central

    Tang, Xiaohui; Reckinger, Nicolas; Poncelet, Olivier; Louette, Pierre; Ureña, Ferran; Idrissi, Hosni; Turner, Stuart; Cabosart, Damien; Colomer, Jean-François; Raskin, Jean-Pierre; Hackens, Benoit; Francis, Laurent A.

    2015-01-01

    Based on micro-Raman spectroscopy (μRS) and X-ray photoelectron spectroscopy (XPS), we study the structural damage incurred in monolayer (1L) and few-layer (FL) graphene subjected to atomic-layer deposition of HfO2 and Al2O3 upon different oxygen plasma power levels. We evaluate the damage level and the influence of the HfO2 thickness on graphene. The results indicate that in the case of Al2O3/graphene, whether 1L or FL graphene is strongly damaged under our process conditions. For the case of HfO2/graphene, μRS analysis clearly shows that FL graphene is less disordered than 1L graphene. In addition, the damage levels in FL graphene decrease with the number of layers. Moreover, the FL graphene damage is inversely proportional to the thickness of HfO2 film. Particularly, the bottom layer of twisted bilayer (t-2L) has the salient features of 1L graphene. Therefore, FL graphene allows for controlling/limiting the degree of defect during the PE-ALD HfO2 of dielectrics and could be a good starting material for building field effect transistors, sensors, touch screens and solar cells. Besides, the formation of Hf-C bonds may favor growing high-quality and uniform-coverage dielectric. HfO2 could be a suitable high-K gate dielectric with a scaling capability down to sub-5-nm for graphene-based transistors. PMID:26311131

  5. Damage evaluation in graphene underlying atomic layer deposition dielectrics.

    PubMed

    Tang, Xiaohui; Reckinger, Nicolas; Poncelet, Olivier; Louette, Pierre; Ureña, Ferran; Idrissi, Hosni; Turner, Stuart; Cabosart, Damien; Colomer, Jean-François; Raskin, Jean-Pierre; Hackens, Benoit; Francis, Laurent A

    2015-01-01

    Based on micro-Raman spectroscopy (μRS) and X-ray photoelectron spectroscopy (XPS), we study the structural damage incurred in monolayer (1L) and few-layer (FL) graphene subjected to atomic-layer deposition of HfO2 and Al2O3 upon different oxygen plasma power levels. We evaluate the damage level and the influence of the HfO2 thickness on graphene. The results indicate that in the case of Al2O3/graphene, whether 1L or FL graphene is strongly damaged under our process conditions. For the case of HfO2/graphene, μRS analysis clearly shows that FL graphene is less disordered than 1L graphene. In addition, the damage levels in FL graphene decrease with the number of layers. Moreover, the FL graphene damage is inversely proportional to the thickness of HfO2 film. Particularly, the bottom layer of twisted bilayer (t-2L) has the salient features of 1L graphene. Therefore, FL graphene allows for controlling/limiting the degree of defect during the PE-ALD HfO2 of dielectrics and could be a good starting material for building field effect transistors, sensors, touch screens and solar cells. Besides, the formation of Hf-C bonds may favor growing high-quality and uniform-coverage dielectric. HfO2 could be a suitable high-K gate dielectric with a scaling capability down to sub-5-nm for graphene-based transistors. PMID:26311131

  6. Method of forming a multiple layer dielectric and a hot film sensor therewith

    NASA Technical Reports Server (NTRS)

    Hopson, Purnell, Jr. (Inventor); Tran, Sang Q. (Inventor)

    1990-01-01

    The invention is a method of forming a multiple layer dielectric for use in a hot-film laminar separation sensor. The multiple layer dielectric substrate is formed by depositing a first layer of a thermoelastic polymer such as on an electrically conductive substrate such as the metal surface of a model to be tested under cryogenic conditions and high Reynolds numbers. Next, a second dielectric layer of fused silica is formed on the first dielectric layer of thermoplastic polymer. A resistive metal film is deposited on selected areas of the multiple layer dielectric substrate to form one or more hot-film sensor elements to which aluminum electrical circuits deposited upon the multiple layered dielectric substrate are connected.

  7. A fast and accurate method to predict 2D and 3D aerodynamic boundary layer flows

    NASA Astrophysics Data System (ADS)

    Bijleveld, H. A.; Veldman, A. E. P.

    2014-12-01

    A quasi-simultaneous interaction method is applied to predict 2D and 3D aerodynamic flows. This method is suitable for offshore wind turbine design software as it is a very accurate and computationally reasonably cheap method. This study shows the results for a NACA 0012 airfoil. The two applied solvers converge to the experimental values when the grid is refined. We also show that in separation the eigenvalues remain positive thus avoiding the Goldstein singularity at separation. In 3D we show a flow over a dent in which separation occurs. A rotating flat plat is used to show the applicability of the method for rotating flows. The shown capabilities of the method indicate that the quasi-simultaneous interaction method is suitable for design methods for offshore wind turbine blades.

  8. Comparison between measured turbine stage performance and the predicted performance using quasi-3D flow and boundary layer analyses

    NASA Technical Reports Server (NTRS)

    Boyle, R. J.; Haas, J. E.; Katsanis, T.

    1984-01-01

    A method for calculating turbine stage performance is described. The usefulness of the method is demonstrated by comparing measured and predicted efficiencies for nine different stages. Comparisons are made over a range of turbine pressure ratios and rotor speeds. A quasi-3D flow analysis is used to account for complex passage geometries. Boundary layer analyses are done to account for losses due to friction. Empirical loss models are used to account for incidence, secondary flow, disc windage, and clearance losses.

  9. CMUTs with High-K Atomic Layer Deposition Dielectric Material Insulation Layer

    PubMed Central

    Xu, Toby; Tekes, Coskun; Degertekin, F. Levent

    2014-01-01

    Use of high-κ dielectric, atomic layer deposition (ALD) materials as an insulation layer material for capacitive micromachined ultrasonic transducers (CMUTs) is investigated. The effect of insulation layer material and thickness on CMUT performance is evaluated using a simple parallel plate model. The model shows that both high dielectric constant and the electrical breakdown strength are important for the dielectric material, and significant performance improvement can be achieved, especially as the vacuum gap thickness is reduced. In particular, ALD hafnium oxide (HfO2) is evaluated and used as an improvement over plasma-enhanced chemical vapor deposition (PECVD) silicon nitride (SixNy) for CMUTs fabricated by a low-temperature, complementary metal oxide semiconductor transistor-compatible, sacrificial release method. Relevant properties of ALD HfO2 such as dielectric constant and breakdown strength are characterized to further guide CMUT design. Experiments are performed on parallel fabricated test CMUTs with 50-nm gap and 16.5-MHz center frequency to measure and compare pressure output and receive sensitivity for 200-nm PECVD SixNy and 100-nm HfO2 insulation layers. Results for this particular design show a 6-dB improvement in receiver output with the collapse voltage reduced by one-half; while in transmit mode, half the input voltage is needed to achieve the same maximum output pressure. PMID:25474786

  10. CMUTs with high-K atomic layer deposition dielectric material insulation layer.

    PubMed

    Xu, Toby; Tekes, Coskun; Degertekin, F

    2014-12-01

    Use of high-κ dielectric, atomic layer deposition (ALD) materials as an insulation layer material for capacitive micromachined ultrasonic transducers (CMUTs) is investigated. The effect of insulation layer material and thickness on CMUT performance is evaluated using a simple parallel plate model. The model shows that both high dielectric constant and the electrical breakdown strength are important for the dielectric material, and significant performance improvement can be achieved, especially as the vacuum gap thickness is reduced. In particular, ALD hafnium oxide (HfO2) is evaluated and used as an improvement over plasma-enhanced chemical vapor deposition (PECVD) silicon nitride (Six)Ny)) for CMUTs fabricated by a low-temperature, complementary metal oxide semiconductor transistor-compatible, sacrificial release method. Relevant properties of ALD HfO2) such as dielectric constant and breakdown strength are characterized to further guide CMUT design. Experiments are performed on parallel fabricated test CMUTs with 50-nm gap and 16.5-MHz center frequency to measure and compare pressure output and receive sensitivity for 200-nm PECVD Six)Ny) and 100-nm HfO2) insulation layers. Results for this particular design show a 6-dB improvement in receiver output with the collapse voltage reduced by one-half; while in transmit mode, half the input voltage is needed to achieve the same maximum output pressure. PMID:25474786

  11. Development of Leaky Wave Antennas for Layered Ridge Dielectric Waveguide

    NASA Technical Reports Server (NTRS)

    Ponchak, George E.; Katehi, Linda P. B.

    1993-01-01

    The millimeter wave, especially above 100 GHz, and the submillimeter wave frequency spectrum offers the possibility for narrow-beam, high-resolution antennas which are critical for high definition radars required for space debris tracking, airport ground avoidance radars, and missile tracking. In addition, the frequency which most atmospheric constituents may be detected lie in this part of the frequency spectrum. Therefore, the development of electronic components for millimeter/submillimeter wave passive sensors is required for environmental monitoring of the Earth's atmosphere. Typical microwave transmission lines such as microstrip and coplanar waveguide rely on two or more electrical conductors to concentrate and guide the electromagnetic energy. Unfortunately, the surface resistance of the conductors increases as the square root of frequency. In addition, the circuit dimensions must be decreased with increasing frequency to maintain a single mode transmission line which further increases the conductor loss. An alternative family of transmission lines are formed from two or more insulating materials and rely on the differences in the permittivities between the two materials to guide the wave. No metal conductors are required although some dielectric waveguides do utilize a metallic ground plane to facilitate the interconnections of active electrical elements or to reduce the transmission line size. Examples of such transmission lines are image guides, insulated image guides, trapped image guides, ridge guide, and layered ridge dielectric waveguide (LRDW). Although most dielectric waveguides have dimensions on the order of lambda to provide sufficient field confinement, the LRDW has been shown to provide good field confinement for electrically small lines. This offers an advantage in circuit integration. It has been shown that a periodic array of metallic strips placed either along or on top of a dielectric waveguide forms an effective radiator. This antenna is

  12. EM modelling of arbitrary shaped anisotropic dielectric objects using an efficient 3D leapfrog scheme on unstructured meshes

    NASA Astrophysics Data System (ADS)

    Gansen, A.; Hachemi, M. El; Belouettar, S.; Hassan, O.; Morgan, K.

    2016-09-01

    The standard Yee algorithm is widely used in computational electromagnetics because of its simplicity and divergence free nature. A generalization of the classical Yee scheme to 3D unstructured meshes is adopted, based on the use of a Delaunay primal mesh and its high quality Voronoi dual. This allows the problem of accuracy losses, which are normally associated with the use of the standard Yee scheme and a staircased representation of curved material interfaces, to be circumvented. The 3D dual mesh leapfrog-scheme which is presented has the ability to model both electric and magnetic anisotropic lossy materials. This approach enables the modelling of problems, of current practical interest, involving structured composites and metamaterials.

  13. Internal waves patterns in the wake of a 3D body towed in a two-layer fluid

    NASA Astrophysics Data System (ADS)

    Lacaze, Laurent; Mercier, Matthieu; Thual, Olivier; Paci, Alexandre

    2014-11-01

    Stratified flows over obstacles are important features in meteorology and oceanography. The characterization of these flows is crucial in order to propose models of geophysical processes such as mixing and ocean circulation or orographic drag in the atmosphere. For some specific stratification profiles, the energy of internal waves generated by the obstacle can be trapped at a given depth, at the base of the oceanic mixing layer or at the top of the atmospheric boundary layer for instance. This scenario can be modelled by a two-layer stratified fluid for which gravity waves spread at the interface between the two layers. The work presented here focuses on a two-layer flow over a 3D obstacle, or equivalently, an obstacle towed in a fluid at rest. Experiments performed both in the large-scale flume of CNRM-GAME Toulouse (METEO-FRANCE & CNRS) and in a smaller tank apparatus, are presented with a specific attention on the measurement of the 3D wave patterns. A non-hydrostatic linear analysis is used to describe the observed wave patterns. The experiments highlight the strong influence of the Froude number on the generated waves. More specifically, we investigate the nature of the wake angle obtained from the wave pattern, and discuss a transition from Kelvin to Mach angle.

  14. Aerodynamic heating on 3-D bodies including the effects of entropy-layer swallowing

    NASA Technical Reports Server (NTRS)

    Dejarnette, F. R.; Hamilton, H. H.

    1974-01-01

    A relatively simple method was developed previously (authors, 1973) for calculating laminar, transitional, and turbulent heating rates on three-dimensional bodies in hypersonic flows. This method was shown to yield reasonably accurate results for laminar heating on blunted circular and elliptical cones and an earlier version of the space shuttle vehicle. As the boundary layer along the surface grows, more and more of the inviscid-flow mass is entrained into the boundary layer, and the streamlines which passed through the nearly normal portion of the bow shock wave are 'swallowed' by the boundary layer. This phenomenon is often referred to as entropy-layer or streamline swallowing, and it can have a significant effect on the calculated heating rates. An approximate, yet simple, method for including the effects of entropy-layer swallowing in the heating-rate calculations is given.

  15. Four- and five-layer silicon-clad dielectric waveguides

    NASA Technical Reports Server (NTRS)

    Mcwright, G.; Batchman, T. E.

    1981-01-01

    Computer modeling studies conducted on four-layer silicon-clad dielectric waveguides indicate that the attenuation (alpha) and mode index (beta/K) behave as exponentially damped sinusoids as the silicon thickness is increased. The observed effect can be explained quite simply as a periodic coupling between the guided modes of the lossless structure and the lossy modes supported by the high-refractive index silicon. The attenuation and mode index are significantly altered by conductivity changes in the silicon; an amplitude modulator and an intensity modulator were proposed using these results. Predicted high attenuations in the device may be reduced significantly with a silicon dioxide buffer layer between the semiconductor and the polystyrene guide. Experimental confirmation of the predicted characteristics is still necessary. A number of thin-silicon film waveguides have been RF sputtered but attenuation measurements to verify the damped oscillatory behavior are forthcoming. Conductivity variations of the silicon should demonstrate the modulation capabilities.

  16. Assembly of cell-laden hydrogel fiber into non-liquefied and liquefied 3D spiral constructs by perfusion-based layer-by-layer technique.

    PubMed

    Sher, Praveen; Oliveira, Sara M; Borges, João; Mano, João F

    2015-01-01

    In this work, three-dimensional (3D) self-sustaining, spiral-shaped constructs were produced through a combination of ionotropic gelation, to form cell-encapsulated alginate fibers, and a perfusion-based layer-by-layer (LbL) technique. Single fibers were assembled over cylindrical molds by reeling to form spiral shapes, both having different geometries and sizes. An uninterrupted nanometric multilayer coating produced by a perfusion-based LbL technique, using alginate and chitosan, generated stable 3D spiral-shaped macrostructures by gripping and affixing the threads together without using any crosslinking/binding agent. The chelation process altered the internal microenvironment of the 3D construct from the solid to the liquefied state while preserving the external geometry. L929 cell viability by MTS and dsDNA quantification favor liquefied 3D constructs more than non-liquefied ones. The proposed technique setup helps us to generate complex polyelectrolyte-based 3D constructs for tissue engineering applications and organ printing. PMID:25562702

  17. High-contrast 3D microscopic imaging of deep layers in a biological medium

    NASA Astrophysics Data System (ADS)

    Faridian, Ahmad; Pedrini, Giancarlo; Osten, Wolfgang

    2014-03-01

    Multilayer imaging of biological specimens is a demanding field of research, but scattering is one of the major obstacles in imaging the internal layers of a specimen. Although in many studies the biological object is assumed to be a weak scatterer, this condition is hardly satisfied for sub-millimeter sized organisms. The scattering medium is inhomogeneously distributed inside the specimen. Therefore, the scattering which occurs in the upper layers of a given internal layer of interest is different from the lower layers. That results in a different amount of collectable information for a specific point in the layer from each view. An opposed view dark-field digital holographic microscope (DHM) has been implemented in this work to collect the information concurrently from both views and increase the image quality. Implementing a DHM system gives the possibility to perform digital refocusing process and obtain multilayer images from each side without depth scanning of the object. The results have been presented and discussed here for a Drosophila embryo.

  18. Physical properties and microstructures of nanocrystals reinforced ice laser 3D print layer

    NASA Astrophysics Data System (ADS)

    Li, Jia-Ning; Liu, Ke-Gao; Gong, Shui-Li; Zhang, Yuan-Bin; Liu, Peng

    2015-02-01

    Rapid prototyping based on laser alloying by the pre-placed mixed powders has been used to produce the nanocrystals reinforced three-dimensional layer in this study. Such a layer was fabricated on a TC17 titanium alloy by laser rapid prototyping (LRP) of the Co-Sb-TiB2 mixed powders in ice. Scanning electron microscope (SEM) and high resolution transmission electron microscopy (HRTEM) test results indicated that the ice addition was able to decrease the maximum temperature of molten pool during the LRP process, favoring the formation of nanocrystals; growth of such nanocrystals was retarded by the surrounded amorphous in a certain extent, favoring the formations of ultrafine nanoparticles (UN), and the twin crystals and the high-angle grain boundaries were also observed; differential thermal analysis (DTA) test was used to explain the physical properties and formation mechanism of amorphous-nanocrystals, and also the relationship between the amorphous and nanocrystalline phases in such a LRP layer.

  19. One-layer microfluidic device for hydrodynamic 3D self-flow-focusing operating in low flow speed

    NASA Astrophysics Data System (ADS)

    Daghighi, Yasaman; Gnyawali, Vaskar; Strohm, Eric M.; Tsai, Scott S. H.; Kolios, Michael C.

    2016-03-01

    Hydrodynamic 3D flow-focusing techniques in microfluidics are categorized as (a) sheathless techniques which require high flow rates and long channels, resulting in high operating cost and high flow rates which are inappropriate for applications with flow rate limitations, and (b) sheath-flow based techniques which usually require excessive sheath flow rate to achieve hydrodynamic 3D flow-focusing. Many devices based on these principles use complicated fabrication methods to create multi-layer microchannels. We have developed a sheath-flow based microfluidic device that is capable of hydrodynamic 3D self-flow-focusing. In this device the main flow (black ink) in a low speed, and a sheath flow, enter through two inlets and enter a 180 degree curved channel (300 × 300 μm cross-section). Main flow migrates outwards into the sheath-flow due to centrifugal effects and consequently, vertical focusing is achieved at the end of the curved channel. Then, two other sheath flows horizontally confine the main flow to achieve horizontal focusing. Thus, the core flow is three-dimensionally focused at the center of the channel at the downstream. Using centrifugal force for 3D flow-focusing in a single-layer fabricated microchannel has been previously investigated by few groups. However, their demonstrated designs required high flow speed (>1 m/s) which is not suitable for many applications that live biomedical specie are involved. Here, we introduce a new design which is operational in low flow speed (<0.05 m/s) and is suitable for applications involving live cells. This microfluidic device can be used in detecting, counting and isolating cells in many biomedical applications.

  20. A framework for retinal layer intensity analysis for retinal artery occlusion patient based on 3D OCT

    NASA Astrophysics Data System (ADS)

    Liao, Jianping; Chen, Haoyu; Zhou, Chunlei; Chen, Xinjian

    2014-03-01

    Occlusion of retinal artery leads to severe ischemia and dysfunction of retina. Quantitative analysis of the reflectivity in the retina is very needed to quantitative assessment of the severity of retinal ischemia. In this paper, we proposed a framework for retinal layer intensity analysis for retinal artery occlusion patient based on 3D OCT images. The proposed framework consists of five main steps. First, a pre-processing step is applied to the input OCT images. Second, the graph search method was applied to segment multiple surfaces in OCT images. Third, the RAO region was detected based on texture classification method. Fourth, the layer segmentation was refined using the detected RAO regions. Finally, the retinal layer intensity analysis was performed. The proposed method was tested on tested on 27 clinical Spectral domain OCT images. The preliminary results show the feasibility and efficacy of the proposed method.

  1. Improving the dielectric properties of an electrowetting-on-dielectric microfluidic device with a low-pressure chemical vapor deposited Si3N4 dielectric layer

    PubMed Central

    Shen, Hsien-Hua; Chung, Lung-Yuan

    2015-01-01

    Dielectric breakdown is a common problem in a digital microfluidic system, which limits its application in chemical or biomedical applications. We propose a new fabrication of an electrowetting-on-dielectric (EWOD) device using Si3N4 deposited by low-pressure chemical vapor deposition (LPCVD) as a dielectric layer. This material exhibits a greater relative permittivity, purity, uniformity, and biocompatibility than polymeric films. These properties also increase the breakdown voltage of a dielectric layer and increase the stability of an EWOD system when applied in biomedical research. Medium droplets with mouse embryos were manipulated in this manner. The electrical properties of the Si3N4 dielectric layer—breakdown voltage, refractive index, relative permittivity, and variation of contact angle with input voltage—were investigated and compared with a traditional Si3N4 dielectric layer deposited as a plasma-enhanced chemical vapor deposition to confirm the potential of LPCVD Si3N4 applied as the dielectric layer of an EWOD digital microfluidic system. PMID:25825614

  2. Mixing Layer Excitation by Dielectric Barrier Discharge Plasma Actuators

    NASA Astrophysics Data System (ADS)

    Ely, Richard; Little, Jesse

    2012-11-01

    The response of a mixing layer with velocity ratio 0.28 to perturbations near the high-speed side (U2=11 m/s, ReL = 0.26 × 106) of its origin from dielectric barrier discharge plasma actuators is studied experimentally. Both alternating current (ac) and nanosecond (ns) pulse driven plasma are investigated in an effort to clarify the mechanisms associated with each technique as well as the more general physics associated with flow control via momentum-based versus thermal actuation. Ac-DBD plasma actuators, which function through electrohydrodynamic effects, are found to generate an increase in mixing layer momentum thickness that is strongly dependent on forcing frequency. Results are qualitatively similar to previous archival literature on the topic employing oscillating flaps. Ns-DBD plasma, which is believed to function through thermal effects, has no measureable influence on the mixing layer profile at similar forcing conditions. In the context of previous archival literature, these results suggest different physical mechanisms govern active control via ac- and ns-DBD plasma actuation and more generally, momentum versus thermal perturbations. Further investigation of these phenomena will be provided through variation of the boundary/mixing layer properties and forcing parameters in the context of spatially and temporally resolved experimental data. Supported by: AFOSR and Raytheon Missile Systems.

  3. Parallel graph search: application to intraretinal layer segmentation of 3D macular OCT scans

    NASA Astrophysics Data System (ADS)

    Lee, Kyungmoo; Abràmoff, Michael D.; Garvin, Mona K.; Sonka, Milan

    2012-02-01

    Image segmentation is of paramount importance for quantitative analysis of medical image data. Recently, a 3-D graph search method which can detect globally optimal interacting surfaces with respect to the cost function of volumetric images has been introduced, and its utility demonstrated in several application areas. Although the method provides excellent segmentation accuracy, its limitation is a slow processing speed when many surfaces are simultaneously segmented in large volumetric datasets. Here, we propose a novel method of parallel graph search, which overcomes the limitation and allows the quick detection of multiple surfaces. To demonstrate the obtained performance with respect to segmentation accuracy and processing speedup, the new approach was applied to retinal optical coherence tomography (OCT) image data and compared with the performance of the former non-parallel method. Our parallel graph search methods for single and double surface detection are approximately 267 and 181 times faster than the original graph search approach in 5 macular OCT volumes (200 x 5 x 1024 voxels) acquired from the right eyes of 5 normal subjects. The resulting segmentation differences were small as demonstrated by the mean unsigned differences between the non-parallel and parallel methods of 0.0 +/- 0.0 voxels (0.0 +/- 0.0 μm) and 0.27 +/- 0.34 voxels (0.53 +/- 0.66 μm) for the single- and dual-surface approaches, respectively.

  4. Regional application of multi-layer artificial neural networks in 3-D ionosphere tomography

    NASA Astrophysics Data System (ADS)

    Ghaffari Razin, Mir Reza; Voosoghi, Behzad

    2016-08-01

    Tomography is a very cost-effective method to study physical properties of the ionosphere. In this paper, residual minimization training neural network (RMTNN) is used in voxel-based tomography to reconstruct of 3-D ionosphere electron density with high spatial resolution. For numerical experiments, observations collected at 37 GPS stations from Iranian permanent GPS network (IPGN) are used. A smoothed TEC approach was used for absolute STEC recovery. To improve the vertical resolution, empirical orthogonal functions (EOFs) obtained from international reference ionosphere 2012 (IRI-2012) used as object function in training neural network. Ionosonde observations is used for validate reliability of the proposed method. Minimum relative error for RMTNN is 1.64% and maximum relative error is 15.61%. Also root mean square error (RMSE) of 0.17 × 1011 (electrons/m3) is computed for RMTNN which is less than RMSE of IRI2012. The results show that RMTNN has higher accuracy and compiles speed than other ionosphere reconstruction methods.

  5. Hierarchical self-assembly of hexagonal single-crystal nanosheets into 3D layered superlattices with high conductivity.

    PubMed

    Tao, Yulun; Shen, Yuhua; Yang, Liangbao; Han, Bin; Huang, Fangzhi; Li, Shikuo; Chu, Zhuwang; Xie, Anjian

    2012-06-21

    While the number of man-made nano superstructures realized by self-assembly is growing in recent years, assemblies of conductive polymer nanocrystals, especially for superlattices, are still a significant challenge, not only because of the simplicity of the shape of the nanocrystal building blocks and their interactions, but also because of the poor control over these parameters in the fabrication of more elaborate nanocrystals. Here, we firstly report a facile and general route to a new generation of 3D layered superlattices of polyaniline doped with CSA (PANI-CSA) and show how PANI crystallize and self-assemble, in a suitable single solution environment. In cyclohexane, 1D amorphous nanofibers transformed to 1D nanorods as building blocks, and then to 2D single-crystal nanosheets with a hexagonal phase, and lastly to 3D ordered layered superlattices with the narrowest polydispersity value (M(w)/M(n) = 1.47). Remarkably, all the instructions for the hierarchical self-assembly are encoded in the layered shape in other non-polar solvents (hexane, octane) and their conductivity in the π-π stacking direction is improved to about 50 S cm(-1), which is even higher than that of the highest previously reported value (16 S cm(-1)). The method used in this study is greatly expected to be readily scalable to produce superlattices of conductive polymers with high quality and low cost. PMID:22609947

  6. Active millimeter wave detection of concealed layers of dielectric material

    NASA Astrophysics Data System (ADS)

    Bowring, N. J.; Baker, J. G.; Rezgui, N. D.; Southgate, M.; Alder, J. F.

    2007-04-01

    Extensive work has been published on millimetre wave active and passive detection and imaging of metallic objects concealed under clothing. We propose and demonstrate a technique for revealing the depth as well as the outline of partially transparent objects, which is especially suited to imaging layer materials such as explosives and drugs. The technique uses a focussed and scanned FMCW source, swept through many GHz to reveal this structure. The principle involved is that a parallel sided dielectric slab produces reflections at both its upper and lower surfaces, acting as a Fabry-Perot interferometer. This produces a pattern of alternating reflected peaks and troughs in frequency space. Fourier or Burg transforming this pattern into z-space generates a peak at the thickness of the irradiated sample. It could be argued that though such a technique may work for single uniform slabs of dielectric material, it will give results of little or no significance when the sample both scatters the incident radiation and gives erratic reflectivities due to its non-uniform thickness and permittivity . We show results for a variety of materials such as explosive simulants, powder and drugs, both alone and concealed under clothing or in a rucksack, which display strongly directional reflectivities at millimeter wavelengths, and whose location is well displayed by a varying thickness parameter as the millimetre beam is scanned across the target. With this system we find that samples can easily be detected at standoff distances of at least 4.6m.

  7. Optical properties of silica fibers and layered dielectric mirrors

    SciTech Connect

    Cooke, D.W.; Farnum, E.H.; Clinard, F.W. Jr.; Bennett, B.L.; Portis, A.M.

    1996-04-01

    Radioluminescence (RL) from virgin and neutron-irradiated (10{sup 23} n-m{sup -2}) silica fibers has been measured in the temperature interval 4 to 300 K. Unirradiated specimens exhibit a decrease in RL intensity with increasing temperature such that the intensity is extremely weak at room temperature. The luminescence is well described by a barrier-limited exciton mechanism. in contrast, the heavily-irradiated samples show an increase in RL with elevated temperatures such that the intensity at room temperature is about twice that measured at 4 K. Neutron irradiation presumably produces many luminescence centers that act as radiative sites for exciton decay. Absolute specular reflectance of a series of neutron irradiated, layered dielectric mirrors was also measured. In addition to structural damage that has already been reported, we typically found approximately 10% reduction in the reflectance following irradiation. These results suggest that neither fibers nor dielectric mirrors are well suited for use near the high radiation area of the ITER plasma.

  8. Coupling Between Microstrip Lines Embedded in Polyimide Layers for 3D-MMICs on Si

    NASA Technical Reports Server (NTRS)

    Ponchak, George E.; Tentzeris, Emmanouil M.; Papapolymerou, John

    2001-01-01

    Three-dimensional circuits built upon multiple layers of polyimide are required for constructing Si/SiGe monolithic microwave/millimeter-wave integrated circuits on CMOS (low resistivity) Si wafers. However, the closely spaced transmission lines are susceptible to high levels of coupling, which degrades circuit performance. In this paper, Finite Difference Time Domain (FDTD) analysis and measured characteristics of novel shielding structures that significantly reduce coupling between embedded microstrip lines are presented.

  9. Phase-retrieved optical projection tomography for 3D imaging through scattering layers

    NASA Astrophysics Data System (ADS)

    Ancora, Daniele; Di Battista, Diego; Giasafaki, Georgia; Psycharakis, Stylianos; Liapis, Evangelos; Zacharopoulos, Athanasios; Zacharakis, Giannis

    2016-03-01

    Recently great progress has been made in biological and biomedical imaging by combining non-invasive optical methods, novel adaptive light manipulation and computational techniques for intensity-based phase recovery and three dimensional image reconstruction. In particular and in relation to the work presented here, Optical Projection Tomography (OPT) is a well-established technique for imaging mostly transparent absorbing biological models such as C. Elegans and Danio Rerio. On the contrary, scattering layers like the cocoon surrounding the Drosophila during the pupae stage constitutes a challenge for three dimensional imaging through such a complex structure. However, recent studies enabled image reconstruction through scattering curtains up to few transport mean free paths via phase retrieval iterative algorithms allowing to uncover objects hidden behind complex layers. By combining these two techniques we explore the possibility to perform a three dimensional image reconstruction of fluorescent objects embedded between scattering layers without compromising its structural integrity. Dynamical cross correlation registration was implemented for the registration process due to translational and flipping ambiguity of the phase retrieval problem, in order to provide the correct aligned set of data to perform the back-projection reconstruction. We have thus managed to reconstruct a hidden complex object between static scattering curtains and compared with the effective reconstruction to fully understand the process before the in-vivo biological implementation.

  10. Highly sensitive flexible pressure sensors with microstructured rubber dielectric layers

    NASA Astrophysics Data System (ADS)

    Mannsfeld, Stefan C. B.; Tee, Benjamin C.-K.; Stoltenberg, Randall M.; Chen, Christopher V. H.-H.; Barman, Soumendra; Muir, Beinn V. O.; Sokolov, Anatoliy N.; Reese, Colin; Bao, Zhenan

    2010-10-01

    The development of an electronic skin is critical to the realization of artificial intelligence that comes into direct contact with humans, and to biomedical applications such as prosthetic skin. To mimic the tactile sensing properties of natural skin, large arrays of pixel pressure sensors on a flexible and stretchable substrate are required. We demonstrate flexible, capacitive pressure sensors with unprecedented sensitivity and very short response times that can be inexpensively fabricated over large areas by microstructuring of thin films of the biocompatible elastomer polydimethylsiloxane. The pressure sensitivity of the microstructured films far surpassed that exhibited by unstructured elastomeric films of similar thickness, and is tunable by using different microstructures. The microstructured films were integrated into organic field-effect transistors as the dielectric layer, forming a new type of active sensor device with similarly excellent sensitivity and response times.

  11. Implementation of a 3D mixing layer code on parallel computers

    NASA Technical Reports Server (NTRS)

    Roe, K.; Thakur, R.; Dang, T.; Bogucz, E.

    1995-01-01

    This paper summarizes our progress and experience in the development of a Computational-Fluid-Dynamics code on parallel computers to simulate three-dimensional spatially-developing mixing layers. In this initial study, the three-dimensional time-dependent Euler equations are solved using a finite-volume explicit time-marching algorithm. The code was first programmed in Fortran 77 for sequential computers. The code was then converted for use on parallel computers using the conventional message-passing technique, while we have not been able to compile the code with the present version of HPF compilers.

  12. Coupling between Microstrip Lines Embedded in Polyimide Layers for 3D-MMICs on Si

    NASA Technical Reports Server (NTRS)

    Ponchak, George E.; Tentzeris, Emmanouil M.; Papapolymerou, John

    2001-01-01

    Three-dimensional circuits built upon multiple layers of polyimide are required for constructing SilSiGe monolithic microwavdmillimeter-wave integrated circuits on CMOS (low resistivity) Si wafers. However, the closely spaced transmission lines are susceptible to high levels of coupling, which degrades circuit performance. In this paper, Finite Difference Time Domain (FDTD) analysis and measured characteristics of novel shielding structures that significantly reduce coupling between embedded microstrip lines are presented. A discussion of the electric and magnetic field distributions for the coupled microstrip lines is presented to provide a physical rationale for the presented results.

  13. Curing behavior and reaction kinetics of binder resins for 3D-printing investigated by dielectric analysis (DEA)

    NASA Astrophysics Data System (ADS)

    Möginger, B.; Kehret, L.; Hausnerova, B.; Steinhaus, J.

    2016-05-01

    3D-Printing is an efficient method in the field of additive manufacturing. In order to optimize the properties of manufactured parts it is essential to adapt the curing behavior of the resin systems with respect to the requirements. Thus, effects of resin composition, e.g. due to different additives such as thickener and curing agents, on the curing behavior have to be known. As the resin transfers from a liquid to a solid glass the time dependent ion viscosity was measured using DEA with flat IDEX sensors. This allows for a sensitive measurement of resin changes as the ion viscosity changes two to four decades. The investigated resin systems are based on the monomers styrene and HEMA. To account for the effects of copolymerization in the calculation of the reaction kinetics it was assumed that the reaction can be considered as a homo-polymerization having a reaction order n≠1. Then the measured ion viscosity curves are fitted with the solution of the reactions kinetics - the time dependent degree of conversion (DC-function) - for times exceeding the initiation phase representing the primary curing. The measured ion viscosity curves can nicely be fitted with the DC-function and the determined fit parameters distinguish distinctly between the investigated resin compositions.

  14. Creating photo-realistic works in a 3D scene using layers styles to create an animation

    NASA Astrophysics Data System (ADS)

    Avramescu, A. M.

    2015-11-01

    Creating realist objects in a 3D scene is not an easy work. We have to be very careful to make the creation very detailed. If we don't know how to make these photo-realistic works, by using the techniques and a good reference photo we can create an amazing amount of detail and realism. For example, in this article there are some of these detailed methods from which we can learn the techniques necessary to make beautiful and realistic objects in a scene. More precisely, in this paper, we present how to create a 3D animated scene, mainly using the Pen Tool and Blending Options. Indeed, this work is based on teaching some simple ways of using the Layer Styles to create some great shadows, lights, textures and a realistic sense of 3 Dimension. The present work involves also showing how some interesting ways of using the illuminating and rendering options can create a realistic effect in a scene. Moreover, this article shows how to create photo realistic 3D models from a digital image. The present work proposes to present how to use Illustrator paths, texturing, basic lighting and rendering, how to apply textures and how to parent the building and objects components. We also propose to use this proposition to recreate smaller details or 3D objects from a 2D image. After a critic art stage, we are able now to present in this paper the architecture of a design method that proposes to create an animation. The aim is to create a conceptual and methodological tutorial to address this issue both scientifically and in practice. This objective also includes proposing, on strong scientific basis, a model that gives the possibility of a better understanding of the techniques necessary to create a realistic animation.

  15. Inkjet printing of carbon supported platinum 3-D catalyst layers for use in fuel cells

    NASA Astrophysics Data System (ADS)

    Taylor, André D.; Kim, Edward Y.; Humes, Virgil P.; Kizuka, Jeremy; Thompson, Levi T.

    We present a method of using inkjet printing (IJP) to deposit catalyst materials onto gas diffusion layers (GDLs) that are made into membrane electrode assemblies (MEAs) for polymer electrolyte fuel cell (PEMFC). Existing ink deposition methods such as spray painting or screen printing are not well suited for ultra low (<0.5 mg Pt cm -2) loadings. The IJP method can be used to deposit smaller volumes of water based catalyst ink solutions with picoliter precision provided the solution properties are compatible with the cartridge design. By optimizing the dispersion of the ink solution we have shown that this technique can be successfully used with catalysts supported on different carbon black (i.e. XC-72R, Monarch 700, Black Pearls 2000, etc.). Our ink jet printed MEAs with catalyst loadings of 0.020 mg Pt cm -2 have shown Pt utilizations in excess of 16,000 mW mg -1 Pt which is higher than our traditional screen printed MEAs (800 mW mg -1 Pt). As a further demonstration of IJP versatility, we present results of a graded distribution of Pt/C catalyst structure using standard Johnson Matthey (JM) catalyst. Compared to a continuous catalyst layer of JM Pt/C (20% Pt), the graded catalyst structure showed enhanced performance.

  16. Mechanochemical and thermal formation of 1H-benzotriazole coordination polymers and complexes of 3d-transition metals with intriguing dielectric properties.

    PubMed

    Brede, Franziska A; Mühlbach, Friedrich; Sextl, Gerhard; Müller-Buschbaum, Klaus

    2016-07-14

    Liquid-assisted grinding (LAG) reactions have been successfully applied to achieve a series of complexes and coordination polymers based on divalent 3d-transition metal chlorides (TM chlorides) and the aromatic ligand 1H-benzotriazole (BtzH). The obtained substances were investigated via single crystal X-ray, powder X-ray determination and simultaneous DTA/TG analysis as model compounds for structural and chemical influences on their dielectric properties. Depending on the synthesis method, different constitutions and structures are observed. Two polymorphous forms of the 1D polymer [MnCl2(BtzH)2] (1 and 2) as well as the complexes [ZnCl2(BtzH)2]·BtzH (3) and [CoCl2(BtzH)2]·BtzH (4) have been obtained as phase-pure bulk substances via the mechanochemical LAG route, and even single crystals are available. For comparison, thermal reactions were also carried out and have led to the formation of the neutral complexes: [CoCl2(BtzH)2] (5) and [CoCl2(BtzH)4]·4BtzH (6), [ZnCl2(BtzH)2] (7) and the anionic complex BtzH2[CoCl3BtzH] (8). In addition, thermal treatment of 3 yields the benzotriazolium salt {(BtzH)2H}Cl (9). The transition metal compounds were additionally analysed regarding their dielectric properties by frequency-dependent as well as temperature-dependent permittivity investigations. It is intriguing that compounds 1 and 3 show remarkably low dielectric constants and loss factors up to 50 °C highlighting them as potential "low-k materials". PMID:27265300

  17. CVS Filtering of 3D Turbulent Mixing Layers Using Orthogonal Wavelets

    NASA Technical Reports Server (NTRS)

    Schneider, Kai; Farge, Marie; Pellegrino, Giulio; Rogers, Michael

    2000-01-01

    Coherent Vortex Simulation (CVS) filtering has been applied to Direct Numerical Simulation (DNS) data of forced and unforced time-developing turbulent mixing layers. CVS filtering splits the turbulent flow into two orthogonal parts, one corresponding to coherent vortices and the other to incoherent background flow. We have shown that the coherent vortices can be represented by few wavelet modes and that these modes are sufficient to reproduce the vorticity probability distribution function (PDF) and the energy spectrum over the entire inertial range. The remaining incoherent background flow is homogeneous, has small amplitude, and is uncorrelated. These results are compared with those obtained for the same compression rate using large eddy simulation (LES) filtering. In contrast to the incoherent background flow of CVS filtering, the LES subgrid scales have a much larger amplitude and are correlated, which makes their statistical modeling more difficult.

  18. Skin-Friction Measurements in a 3-D, Supersonic Shock-Wave/Boundary-Layer Interaction

    NASA Technical Reports Server (NTRS)

    Wideman, J. K.; Brown, J. L.; Miles, J. B.; Ozcan, O.

    1994-01-01

    The experimental documentation of a three-dimensional shock-wave/boundary-layer interaction in a nominal Mach 3 cylinder, aligned with the free-stream flow, and 20 deg. half-angle conical flare offset 1.27 cm from the cylinder centerline. Surface oil flow, laser light sheet illumination, and schlieren were used to document the flow topology. The data includes surface-pressure and skin-friction measurements. A laser interferometric skin friction data. Included in the skin-friction data are measurements within separated regions and three-dimensional measurements in highly-swept regions. The skin-friction data will be particularly valuable in turbulence modeling and computational fluid dynamics validation.

  19. A note on problems in 3D boundary layer computations in streamline coordinates

    NASA Astrophysics Data System (ADS)

    Scholtysik, M.; Bettelini, M.; Fanneløp, T. K.

    1994-01-01

    Turbulent boundary layers with convergent and divergent external streamlines over a flat plate in the neighbourhood of a plane of symmetry have been computed using a finite-difference method based on streamline coordinates. While the results for the divergent case are generally satisfactory, error growth has been observed for the convergent flowfield. This is most pronounced near the lateral boundary of the computational domain, but also occurs in the plane of symmetry. As an ad-hoc engineering solution, a modified and more restrictive definition of the domain of dependence is proposed, which eliminates the part of the computational domain where the largest error growth occurs. The observed tendency to instability in the convergent case is confirmed by a simplified stability analysis after von Neumann of the uncoupled governing equations.

  20. High-performance III-V MOSFET with nano-stacked high-k gate dielectric and 3D fin-shaped structure

    PubMed Central

    2012-01-01

    A three-dimensional (3D) fin-shaped field-effect transistor structure based on III-V metal-oxide-semiconductor field-effect transistor (MOSFET) fabrication has been demonstrated using a submicron GaAs fin as the high-mobility channel. The fin-shaped channel has a thickness-to-width ratio (TFin/WFin) equal to 1. The nano-stacked high-k Al2O3 dielectric was adopted as a gate insulator in forming a metal-oxide-semiconductor structure to suppress gate leakage. The 3D III-V MOSFET exhibits outstanding gate controllability and shows a high Ion/Ioff ratio > 105 and a low subthreshold swing of 80 mV/decade. Compared to a conventional Schottky gate metal–semiconductor field-effect transistor or planar III-V MOSFETs, the III-V MOSFET in this work exhibits a significant performance improvement and is promising for future development of high-performance n-channel devices based on III-V materials. PMID:22853458

  1. High-performance III-V MOSFET with nano-stacked high-k gate dielectric and 3D fin-shaped structure.

    PubMed

    Chen, Szu-Hung; Liao, Wen-Shiang; Yang, Hsin-Chia; Wang, Shea-Jue; Liaw, Yue-Gie; Wang, Hao; Gu, Haoshuang; Wang, Mu-Chun

    2012-01-01

    A three-dimensional (3D) fin-shaped field-effect transistor structure based on III-V metal-oxide-semiconductor field-effect transistor (MOSFET) fabrication has been demonstrated using a submicron GaAs fin as the high-mobility channel. The fin-shaped channel has a thickness-to-width ratio (TFin/WFin) equal to 1. The nano-stacked high-k Al2O3 dielectric was adopted as a gate insulator in forming a metal-oxide-semiconductor structure to suppress gate leakage. The 3D III-V MOSFET exhibits outstanding gate controllability and shows a high Ion/Ioff ratio > 105 and a low subthreshold swing of 80 mV/decade. Compared to a conventional Schottky gate metal-semiconductor field-effect transistor or planar III-V MOSFETs, the III-V MOSFET in this work exhibits a significant performance improvement and is promising for future development of high-performance n-channel devices based on III-V materials. PMID:22853458

  2. Engineered Coalescence by Annealing 3D Ge Microstructures into High-Quality Suspended Layers on Si.

    PubMed

    Salvalaglio, Marco; Bergamaschini, Roberto; Isa, Fabio; Scaccabarozzi, Andrea; Isella, Giovanni; Backofen, Rainer; Voigt, Axel; Montalenti, Francesco; Capellini, Giovanni; Schroeder, Thomas; von Känel, Hans; Miglio, Leo

    2015-09-01

    The move from dimensional to functional scaling in microelectronics has led to renewed interest toward integration of Ge on Si. In this work, simulation-driven experiments leading to high-quality suspended Ge films on Si pillars are reported. Starting from an array of micrometric Ge crystals, the film is obtained by exploiting their temperature-driven coalescence across nanometric gaps. The merging process is simulated by means of a suitable surface-diffusion model within a phase-field approach. The successful comparison between experimental and simulated data demonstrates that the morphological evolution is driven purely by the lowering of surface-curvature gradients. This allows for fine control over the final morphology to be attained. At fixed annealing time and temperature, perfectly merged films are obtained from Ge crystals grown at low temperature (450 °C), whereas some void regions still persist for crystals grown at higher temperature (500 °C) due to their different initial morphology. The latter condition, however, looks very promising for possible applications. Indeed, scanning tunneling electron microscopy and high-resolution transmission electron microscopy analyses show that, at least during the first stages of merging, the developing film is free from threading dislocations. The present findings, thus, introduce a promising path to integrate Ge layers on Si with a low dislocation density. PMID:26252761

  3. Hierarchical self-assembly of hexagonal single-crystal nanosheets into 3D layered superlattices with high conductivity

    NASA Astrophysics Data System (ADS)

    Tao, Yulun; Shen, Yuhua; Yang, Liangbao; Han, Bin; Huang, Fangzhi; Li, Shikuo; Chu, Zhuwang; Xie, Anjian

    2012-05-01

    While the number of man-made nano superstructures realized by self-assembly is growing in recent years, assemblies of conductive polymer nanocrystals, especially for superlattices, are still a significant challenge, not only because of the simplicity of the shape of the nanocrystal building blocks and their interactions, but also because of the poor control over these parameters in the fabrication of more elaborate nanocrystals. Here, we firstly report a facile and general route to a new generation of 3D layered superlattices of polyaniline doped with CSA (PANI-CSA) and show how PANI crystallize and self-assemble, in a suitable single solution environment. In cyclohexane, 1D amorphous nanofibers transformed to 1D nanorods as building blocks, and then to 2D single-crystal nanosheets with a hexagonal phase, and lastly to 3D ordered layered superlattices with the narrowest polydispersity value (Mw/Mn = 1.47). Remarkably, all the instructions for the hierarchical self-assembly are encoded in the layered shape in other non-polar solvents (hexane, octane) and their conductivity in the π-π stacking direction is improved to about 50 S cm-1, which is even higher than that of the highest previously reported value (16 S cm-1). The method used in this study is greatly expected to be readily scalable to produce superlattices of conductive polymers with high quality and low cost.While the number of man-made nano superstructures realized by self-assembly is growing in recent years, assemblies of conductive polymer nanocrystals, especially for superlattices, are still a significant challenge, not only because of the simplicity of the shape of the nanocrystal building blocks and their interactions, but also because of the poor control over these parameters in the fabrication of more elaborate nanocrystals. Here, we firstly report a facile and general route to a new generation of 3D layered superlattices of polyaniline doped with CSA (PANI-CSA) and show how PANI crystallize and

  4. Cross linking molecular systems to form ultrathin dielectric layers

    NASA Astrophysics Data System (ADS)

    Feng, Danqin

    Dehydrogenation leads to cross linking of polymer or polymer like formation in very different systems: self-assembled monolayers and in closo -carboranes leading to the formation of semiconducting and dielectric boron carbide. We find evidence of intermolecular interactions for a self-assembled monolayer (SAM) formed from a large molecular adsorbate, [1,1';4',1"-terphenyl]-4,4"-dimethanethiol, from the dispersion of the molecular orbitals with changing the wave vector k and from the changes with temperature. With the formation self assembled molecular (SAM) layer, the molecular orbitals hybridize to electronic bands, with indications of significant band dispersion of the unoccupied molecular orbitals. Although organic adsorbates and thin films are generally regarded as "soft" materials, the effective Debye temperature, indicative of the dynamic motion of the lattice normal to the surface, can be very high, e.g. in the multilayer film formed from [1,1'-biphenyl]-4,4'-dimethanethiol (BPDMT). Depending on molecular orientation, the effective Debye temperature can be comparable to that of graphite due to the 'stiffness' of the benzene rings, but follows the expected Debye-Waller behavior for the core level photoemission intensities with temperature. This is not always the case. We find that a monomolecular film formed from [1,1';4',1"-terphenyl]-4,4"-dimethanethiol deviates from Debye-Waller temperature behavior and is likely caused by temperature dependent changes in molecular orientation. We also find evidence for the increase in dielectric character with polymerization (cross-linking) in spite of the decrease in the HOMO-LUMO gap upon irradiation of TPDMT. The changes in the HOMO-LUMO gap, with cross-linking, are roughly consistent with the band dispersion. The decomposition and cross-linking processes are also accompanied by changes in molecular orientation. The energetics of the three isomeric carborane cage compounds [ closo-1,2-orthocarborane, closo-1

  5. Investigation of Nonvolatile Memory Effect of Organic Thin-Film Transistors with Triple Dielectric Layers

    NASA Astrophysics Data System (ADS)

    Yu, Hsin-Chieh; Chen, Ying-Chih; Huang, Chun-Yuan; Su, Yan-Kuin

    2012-03-01

    Pentacene thin-film transistor (TFT) memory using poly(2-hydroxyethyl methacrylate) (PHEMA)-based polymer dielectric layers has been developed. The electric performance and memory behaviors of memory TFTs can be significantly improved by using triple polymer dielectric layers consisting of PHEMA/poly(methyl methacrylate) (PMMA)/PHEMA. This can be attributed to the improvement of the channel/dielectric interface. This memory effect is due to the charge storage of the dipolar group or molecules in the dielectric. The devices exhibit a wide memory window (ΔVth, >20 V), switchable channel current, and long retention time.

  6. Aligned 3D human aortic smooth muscle tissue via layer by layer technique inside microchannels with novel combination of collagen and oxidized alginate hydrogel.

    PubMed

    Rayatpisheh, Shahrzad; Poon, Yin Fun; Cao, Ye; Feng, Jie; Chan, Vincent; Chan-Park, Mary B

    2011-08-01

    Tissue engineering of the small diameter blood vessel medial layer has been challenging. Recreation of the circumferentially aligned multilayer smooth muscle tissue has been one of the major technical difficulties. Some research has utilized cyclic stress to align smooth muscle cells (SMCs) but due to the long time conditioning needed, it was not possible to use primary human cells because of expeditious senescence occurred . We demonstrate rapid buildup of a homogeneous relatively thick (30-40 μm) aligned smooth muscle tissue via layer by layer (LBL) technique within microchannels and a soft cell-adhesive hydrogel. Using a microchannelled scaffold with gapped microwalls, two layers of primary human SMCs separated by an interlayer hydrogel were cultured to confluence within the microchannels. The SMCs aligned along the microchannels because of the physically constraining microwalls. A novel double layered gel consisting of a mixture of pristine and oxidized alginate hydrogel coated with collagen was designed to place between each layer of cells, leading to a thicker tissue in a shorter time. The SMCs penetrated the soft thin interlayer hydrogel within 6 days of seeding of the 2nd cell layer so that the entire construct became more or less homogeneously populated by the SMCs. The unique LBL technique applied within the micropatterned scaffold using a soft cell-adhesive gel interlayer allows rapid growth and confluence of SMCs on 2D surface but at the same time aligns the cells and builds up multiple layers into a 3D tissue. This pseudo-3D buildup method avoids the typical steric resistance of hydrogel embedding. PMID:21548018

  7. Investigation on dielectric properties of atomic layer deposited Al{sub 2}O{sub 3} dielectric films

    SciTech Connect

    Yıldız, Dilber Esra; Yıldırım, Mert; Gökçen, Muharrem

    2014-05-15

    Al/Al{sub 2}O{sub 3}/p-Si Schottky barrier diodes (SBDs) were fabricated using atomic layer deposition technique in order to investigate dielectric properties of SBDs. For this purpose, admittance measurements were conducted at room temperature between −1 V and 3 V in the frequency range of 10 kHz and 1 MHz. In addition to the investigation of Al{sub 2}O{sub 3} morphology using atomic force microscope, dielectric parameters; such as dielectric constant (ε′), dielectric loss (ε″), dielectric loss tangent (tan δ), and real and imaginary parts of dielectric modulus (M′ and M″, respectively), were calculated and effect of frequency on these parameters of Al/Al{sub 2}O{sub 3}/p-Si SBDs was discussed. Variations in these parameters at low frequencies were associated with the effect of interface states in low frequency region. Besides dielectric parameters, ac electrical conductivity of these SBDs was also investigated.

  8. Fast and memory-efficient LOGISMOS graph search for intraretinal layer segmentation of 3D macular OCT scans

    NASA Astrophysics Data System (ADS)

    Lee, Kyungmoo; Zhang, Li; Abramoff, Michael D.; Sonka, Milan

    2015-03-01

    Image segmentation is important for quantitative analysis of medical image data. Recently, our research group has introduced a 3-D graph search method which can simultaneously segment optimal interacting surfaces with respect to the cost function in volumetric images. Although it provides excellent segmentation accuracy, it is computationally demanding (both CPU and memory) to simultaneously segment multiple surfaces from large volumetric images. Therefore, we propose a new, fast, and memory-efficient graph search method for intraretinal layer segmentation of 3-D macular optical coherence tomograpy (OCT) scans. The key idea is to reduce the size of a graph by combining the nodes with high costs based on the multiscale approach. The new approach requires significantly less memory and achieves significantly faster processing speeds (p < 0.01) with only small segmentation differences compared to the original graph search method. This paper discusses sub-optimality of this approach and assesses trade-off relationships between decreasing processing speed and increasing segmentation differences from that of the original method as a function of employed scale of the underlying graph construction.

  9. 3D Dynamics of the Near-Surface Layer of the Ocean in the Presence of Freshwater Influx

    NASA Astrophysics Data System (ADS)

    Dean, C.; Soloviev, A.

    2015-12-01

    Freshwater inflow due to convective rains or river runoff produces lenses of freshened water in the near surface layer of the ocean. These lenses are localized in space and typically involve both salinity and temperature anomalies. Due to significant density anomalies, strong pressure gradients develop, which result in lateral spreading of freshwater lenses in a form resembling gravity currents. Gravity currents inherently involve three-dimensional dynamics. The gravity current head can include the Kelvin-Helmholtz billows with vertical density inversions. In this work, we have conducted a series of numerical experiments using computational fluid dynamics tools. These numerical simulations were designed to elucidate the relationship between vertical mixing and horizontal advection of salinity under various environmental conditions and potential impact on the pollution transport including oil spills. The near-surface data from the field experiments in the Gulf of Mexico during the SCOPE experiment were available for validation of numerical simulations. In particular, we observed a freshwater layer within a few-meter depth range and, in some cases, a density inversion at the edge of the freshwater lens, which is consistent with the results of numerical simulations. In conclusion, we discuss applicability of these results to the interpretation of Aquarius and SMOS sea surface salinity satellite measurements. The results of this study indicate that 3D dynamics of the near-surface layer of the ocean are essential in the presence of freshwater inflow.

  10. The 3D Structure of Flux Tubes That Admit Flute Instability in the Scrape-Off-Layer (SOL) of Tokamaks

    NASA Astrophysics Data System (ADS)

    Takahashi, Hironori

    2014-10-01

    A severe reduction in size down to an ion gyro-radius scale, commonly known as ``squeezing,'' in a lateral dimension of the cross section of a flux tube is traditionally thought to inhibit the occurrence of the flute instability in the Scrape-off-Layer of a diverted tokamak by isolating the main volume of the flux tube from its ends at electrically conducting target plates. A study reported here in the 3D flux tube structure reveals the absence of squeezing for a flux tube that is sufficiently large in its toroidal extent (small toroidal harmonic number n) and located in a layer of low field-line shear around the ``sweet spot'' (about mid-way between the primary and secondary separatrices). The low-shear layer does not hence inhibit the flute instability through the squeezing mechanism, and may thus restore the flute instability, among the most virulent in the magnetized plasma, to the ranks of candidate electrostatic instabilities thought to underlie the turbulence in the SOL in tokamaks. Variations along the flux tube of geometrical characteristics including the cross section will be calculated to develop criteria for the absence of squeezing. Supported in part by the US DOE under DE-AC02-09CH11466.

  11. Effect of Refractive Status and Axial Length on Peripapillary Retinal Nerve Fibre Layer Thickness: An Analysis Using 3D OCT

    PubMed Central

    Sowmya, V.; Venkataramanan, V.R.

    2015-01-01

    Background Accurate measurement of retinal nerve fiber layer (RNFL) is now possible with the high resolution optical coherence tomography (OCT). Effect of refractive status of the eye on RNFL thickness may be relevant in the diagnosis of glaucoma and other optic nerve diseases. Aim To assess the RNFL thickness and compare its correlation with refractive status and axial length of the eye. Material and Methods Three hundred eyes of 150 patients were included in this study, who underwent RNFL analysis using TOPCON 3D OCT 2000. Analysis of variance has been used to find the significance of study parameters between the study groups. Results The study showed that refractive status/axial length affected the peripapillary RNFL thickness significantly. Conclusion The study suggests that the diagnostic accuracy of OCT may be improved by considering refractive status and axial length of the eye when RNFL is measured. PMID:26500931

  12. Self-assembled 3D flower-like Ni2+-Fe3+ layered double hydroxides and their calcined products.

    PubMed

    Xiao, Ting; Tang, Yiwen; Jia, Zhiyong; Li, Dawei; Hu, Xiaoyan; Li, Bihui; Luo, Lijuan

    2009-11-25

    This paper describes a facile solvothermal method to synthesize self-assembled three-dimensional (3D) Ni2+-Fe3+ layered double hydroxides (LDHs). Flower-like Ni2+-Fe3+ LDHs constructed of thin nanopetals were obtained using ethylene glycol (EG) as a chelating reagent and urea as a hydrolysis agent. The reaction mechanism and self-assembly process are discussed. After calcinating the as-prepared LDHs at 450 degrees C in nitrogen gas, porous NiO/NiFe2O4 nanosheets were obtained. This work resulted in the development of a simple, cheap, and effective route for the fabrication of large area Ni2+-Fe3+ LDHs as well as porous NiO/NiFe2O4 nanosheets. PMID:19858561

  13. Simulation of dual-gate SOI MOSFET with different dielectric layers

    NASA Astrophysics Data System (ADS)

    Yadav, Jyoti; Chaudhary, R.; Mukhiya, R.; Sharma, R.; Khanna, V. K.

    2016-04-01

    The paper presents the process design and simulation of silicon-on-insulator (SOI)-based dual-gate metal oxide field-effect transistor (DG-MOSFET) stacked with different dielectric layers on the top of gate oxide. A detailed 2D process simulation of SOI-MOSFETs and its electrical characterization has been done using SILVACO® TCAD tool. A variation in transconductance was observed with different dielectric layers, AlN-gate MOSFET having the highest tranconductance value as compared to other three dielectric layers (SiO2, Si3N4 and Al2O3).

  14. Rupture force of adsorbed self-assembled surfactant layers. Effect of the dielectric exchange force

    NASA Astrophysics Data System (ADS)

    Teschke, O.; Ceotto, G.; de Souza, E. F.

    2001-08-01

    The tip applied force necessary to obtain tip/substrate contact, i.e., rupture force between adsorbed layers of self-assembled surfactant films and atomic force microscope (AFM) tips in water has been measured. A substantial contribution of this rupture force is due to the dielectric exchange force (DEF). The DEF model is in agreement with the observation that the surfactant layer rupture forces are smaller in the thickest layers, where the compactness of the adsorbed film results in the smallest values of the dielectric permittivity. Within experimental accuracy a dielectric permittivity value of ˜4 for bilayers and of ˜36 for monolayers is found.

  15. Layered CU-based electrode for high-dielectric constant oxide thin film-based devices

    DOEpatents

    Auciello, Orlando

    2010-05-11

    A layered device including a substrate; an adhering layer thereon. An electrical conducting layer such as copper is deposited on the adhering layer and then a barrier layer of an amorphous oxide of TiAl followed by a high dielectric layer are deposited to form one or more of an electrical device such as a capacitor or a transistor or MEMS and/or a magnetic device.

  16. Solid Electrolyte Lithium Phosphous Oxynitride as a Protective Nanocladding Layer for 3D High-Capacity Conversion Electrodes.

    PubMed

    Lin, Chuan-Fu; Noked, Malachi; Kozen, Alexander C; Liu, Chanyuan; Zhao, Oliver; Gregorczyk, Keith; Hu, Liangbing; Lee, Sang Bok; Rubloff, Gary W

    2016-02-23

    Materials that undergo conversion reactions to form different materials upon lithiation typically offer high specific capacity for energy storage applications such as Li ion batteries. However, since the reaction products often involve complex mixtures of electrically insulating and conducting particles and significant changes in volume and phase, the reversibility of conversion reactions is poor, preventing their use in rechargeable (secondary) batteries. In this paper, we fabricate and protect 3D conversion electrodes by first coating multiwalled carbon nanotubes (MWCNT) with a model conversion material, RuO2, and subsequently protecting them with conformal thin-film lithium phosphous oxynitride (LiPON), a well-known solid-state electrolyte. Atomic layer deposition is used to deposit the RuO2 and the LiPON, thus forming core double-shell MWCNT@RuO2@LiPON electrodes as a model system. We find that the LiPON protection layer enhances cyclability of the conversion electrode, which we attribute to two factors. (1) The LiPON layer provides high Li ion conductivity at the interface between the electrolyte and the electrode. (2) By constraining the electrode materials mechanically, the LiPON protection layer ensures electronic connectivity and thus conductivity during lithiation/delithiation cycles. These two mechanisms are striking in their ability to preserve capacity despite the profound changes in structure and composition intrinsic to conversion electrode materials. This LiPON-protected structure exhibits superior cycling stability and reversibility as well as decreased overpotentials compared to the unprotected core-shell structure. Furthermore, even at very low lithiation potential (0.05 V), the LiPON-protected electrode largely reduces the formation of a solid electrolyte interphase. PMID:26820038

  17. 3D spin-flop transition in enhanced 2D layered structure single crystalline TlCo2Se2.

    PubMed

    Jin, Z; Xia, Z-C; Wei, M; Yang, J-H; Chen, B; Huang, S; Shang, C; Wu, H; Zhang, X-X; Huang, J-W; Ouyang, Z-W

    2016-10-01

    The enhanced 2D layered structure single crystalline TlCo2Se2 has been successfully fabricated, which exhibits field-induced 3D spin-flop phase transitions. In the case of the magnetic field parallel to the c-axis (B//c), the applied magnetic field induces the evolution of the noncollinear helical magnetic coupling into a ferromagnetic (FM) state with all the magnetization of the Co ion parallel to the c-axis. A striking variation of the field-induced strain within the ab-plane is noticed in the magnetic field region of 20-30 T. In the case of the magnetic field perpendicular to the c-axis (B  ⊥  c), the inter-layer helical antiferromagnetic (AFM) coupling may transform to an initial canted AFM coupling, and then part of it transforms to an intermediate metamagnetic phase with the alignment of two-up-one-down Co magnetic moments and finally to an ultimate FM coupling in higher magnetic fields. The robust noncollinear AFM magnetic coupling is completely destroyed above 30 T. In combination with the measurements of magnetization, magnetoresistance and field-induced strain, a complete magnetic phase diagram of the TlCo2Se2 single crystal has been depicted, demonstrating complex magnetic structures even though the crystal geometry itself gives no indication of the magnetic frustration. PMID:27485370

  18. 3D Wind Reconstruction and Turbulence Estimation in the Boundary Layer from Doppler Lidar Measurements using Particle Method

    NASA Astrophysics Data System (ADS)

    Rottner, L.; Baehr, C.

    2014-12-01

    Turbulent phenomena in the atmospheric boundary layer (ABL) are characterized by small spatial and temporal scales which make them difficult to observe and to model.New remote sensing instruments, like Doppler Lidar, give access to fine and high-frequency observations of wind in the ABL. This study suggests to use a method of nonlinear estimation based on these observations to reconstruct 3D wind in a hemispheric volume, and to estimate atmospheric turbulent parameters. The wind observations are associated to particle systems which are driven by a local turbulence model. The particles have both fluid and stochastic properties. Therefore, spatial averages and covariances may be deduced from the particles. Among the innovative aspects, we point out the absence of the common hypothesis of stationary-ergodic turbulence and the non-use of particle model closure hypothesis. Every time observations are available, 3D wind is reconstructed and turbulent parameters such as turbulent kinectic energy, dissipation rate, and Turbulent Intensity (TI) are provided. This study presents some results obtained using real wind measurements provided by a five lines of sight Lidar. Compared with classical methods (e.g. eddy covariance) our technic renders equivalent long time results. Moreover it provides finer and real time turbulence estimations. To assess this new method, we suggest computing independently TI using different observation types. First anemometer data are used to have TI reference.Then raw and filtered Lidar observations have also been compared. The TI obtained from raw data is significantly higher than the reference one, whereas the TI estimated with the new algorithm has the same order.In this study we have presented a new class of algorithm to reconstruct local random media. It offers a new way to understand turbulence in the ABL, in both stable or convective conditions. Later, it could be used to refine turbulence parametrization in meteorological meso-scale models.

  19. 3D effects of edge magnetic field configuration on divertor/scrape-off layer transport and optimization possibilities for a future reactor

    NASA Astrophysics Data System (ADS)

    Kobayashi, M.; Xu, Y.; Ida, K.; Corre, Y.; Feng, Y.; Schmitz, O.; Frerichs, H.; Tabares, F. L.; Evans, T. E.; Coenen, J. W.; Liang, Y.; Bader, A.; Itoh, K.; Yamada, H.; Ghendrih, Ph.; Ciraolo, G.; Tafalla, D.; Lopez-Fraguas, A.; Guo, H. Y.; Cui, Z. Y.; Reiter, D.; Asakura, N.; Wenzel, U.; Morita, S.; Ohno, N.; Peterson, B. J.; Masuzaki, S.

    2015-10-01

    This paper assesses the three-dimensional (3D) effects of the edge magnetic field structure on divertor/scrape-off layer transport, based on an inter-machine comparison of experimental data and on the recent progress of 3D edge transport simulation. The 3D effects are elucidated as a consequence of competition between transports parallel (\\parallel ) and perpendicular (\\bot ) to the magnetic field, in open field lines cut by divertor plates, or in magnetic islands. The competition has strong impacts on divertor functions, such as determination of the divertor density regime, impurity screening and detachment control. The effects of magnetic perturbation on the edge electric field and turbulent transport are also discussed. Parameterization to measure the 3D effects on the edge transport is attempted for the individual divertor functions. Based on the suggested key parameters, an operation domain of the 3D divertor configuration is discussed for future devices.

  20. Thickness-dependent Dielectric Constant of Few-layer In2Se3 Nano-flakes

    NASA Astrophysics Data System (ADS)

    Wu, Di; Pak, Alexander; Liu, Yingnan; Wu, Xiaoyu; Ren, Yuan; Tsai, Yu-Hao; Lin, Min; Peng, Hailin; Hwang, Gyeong; Lai, Keji

    2015-03-01

    The dielectric constant or relative permittivity of active materials in electronic devices is a critical parameter for charging and screening effects. For layered two-dimensional (2D) materials, it is of great interest to understand how their dielectric constants depend on dimensionalities and the arrangement of crystal lattices. Here we present both experimental and theoretical investigations on the dielectric constant of few-layer In2Se3 nano-flakes grown on mica substrates by van der Waals epitaxy. A nondestructive microwave impedance microscope (MIM) is employed to simultaneously quantify the number of layers and local electrical and optical properties. The measured effective dielectric constant increases monotonically as a function of the thickness and saturates to the bulk value at around 6-8 quintuple layers. The same trend of layer-dependent dielectric constant is also revealed through a density functional theory approach. Our results of the dielectric response are expected to be significant for the applications of layered materials in nano-devices.

  1. Highly Sensitive, Flexible, and Wearable Pressure Sensor Based on a Giant Piezocapacitive Effect of Three-Dimensional Microporous Elastomeric Dielectric Layer.

    PubMed

    Kwon, Donguk; Lee, Tae-Ik; Shim, Jongmin; Ryu, Seunghwa; Kim, Min Seong; Kim, Seunghwan; Kim, Taek-Soo; Park, Inkyu

    2016-07-01

    We report a flexible and wearable pressure sensor based on the giant piezocapacitive effect of a three-dimensional (3-D) microporous dielectric elastomer, which is capable of highly sensitive and stable pressure sensing over a large tactile pressure range. Due to the presence of micropores within the elastomeric dielectric layer, our piezocapacitive pressure sensor is highly deformable by even very small amounts of pressure, leading to a dramatic increase in its sensitivity. Moreover, the gradual closure of micropores under compression increases the effective dielectric constant, thereby further enhancing the sensitivity of the sensor. The 3-D microporous dielectric layer with serially stacked springs of elastomer bridges can cover a much wider pressure range than those of previously reported micro-/nanostructured sensing materials. We also investigate the applicability of our sensor to wearable pressure-sensing devices as an electronic pressure-sensing skin in robotic fingers as well as a bandage-type pressure-sensing device for pulse monitoring at the human wrist. Finally, we demonstrate a pressure sensor array pad for the recognition of spatially distributed pressure information on a plane. Our sensor, with its excellent pressure-sensing performance, marks the realization of a true tactile pressure sensor presenting highly sensitive responses to the entire tactile pressure range, from ultralow-force detection to high weights generated by human activity. PMID:27286001

  2. Positional isomerism-driven two 3D pillar-layered metal-organic frameworks: Syntheses, topological structures and photoluminescence properties

    NASA Astrophysics Data System (ADS)

    Sun, Yayong; Zhao, Siwei; Ma, Haoran; Han, Yi; Liu, Kang; Wang, Lei

    2016-06-01

    Two novel three-dimensional (3D) pillar-layered metal-organic frameworks (MOFs), namely [Zn2(μ2-OH)(boaba)(1,4-bmimb)]n (1) and {[Zn5K2(μ2-H2O)2(boaba)4(1,2-bmimb)2(H2O)2]·H2O}n (2), were prepared by hydrothermal reactions (H3boaba=3,5-bis-oxyacetate-benzoic acid; 1,4-bmimb=1,4-bis((2-methyl-1H-imidazol-1-yl)methyl)benzene; 1,2-bmimb =1,2-bis((2-methyl-1H-imidazol-1-yl)methyl)benzene). Notably, 1 exhibits a (3,5)-connected binodal (63)(69·8)-gra net with binuclear [Zn2(μ2-OH)(COO)]2+ clusters, while 2 shows a novel (4,4,5,9)-connected 4-nodal net constructed from the unique Zn(II)-K(I) heterometal rod-like substructures. The results indicate that the disposition of the 2-methylimidazolyl groups of bis(imidazole) ligands have a significant effect on structural diversity. Moreover, the photoluminescence properties of 1 and 2 have been investigated.

  3. Multigrid mapping and box relaxation for simulation of the whole process of flow transition in 3-D boundary layers

    SciTech Connect

    Liu, C.; Liu, Z.

    1994-12-31

    A new multilevel technology was developed in this study which provides a successful numerical simulation for the whole process of flow transition in 3-D flat plate boundary layers, including linear growth, secondary instability, breakdown, and transition on a relatively coarse grid with low CPU cost. A fourth-order finite difference scheme on stretched and staggered grids, a fully implicit time-marching technique, a semi-coarsening multigrid based on the so-called approximate line-box relaxation, and a buffer domain for the outflow boundary conditions were all employed for high-order accuracy, good stability, and fast convergence. A new fine-coarse-fine grid mapping technique was developed to catch the large eddies and represent main roles of small eddies to keep the code running after the laminar flow breaks down. The computational results are in good agreement with linear stability theory, secondary instability theory, and some experiments. The computation also reproduced the K-type and C-type transition observed by laboratory experiments. The CPU cost for a typical case is around 2-9 CRAY-YMP hours.

  4. Liver Tumor Segmentation from MR Images Using 3D Fast Marching Algorithm and Single Hidden Layer Feedforward Neural Network

    PubMed Central

    2016-01-01

    Objective. Our objective is to develop a computerized scheme for liver tumor segmentation in MR images. Materials and Methods. Our proposed scheme consists of four main stages. Firstly, the region of interest (ROI) image which contains the liver tumor region in the T1-weighted MR image series was extracted by using seed points. The noise in this ROI image was reduced and the boundaries were enhanced. A 3D fast marching algorithm was applied to generate the initial labeled regions which are considered as teacher regions. A single hidden layer feedforward neural network (SLFN), which was trained by a noniterative algorithm, was employed to classify the unlabeled voxels. Finally, the postprocessing stage was applied to extract and refine the liver tumor boundaries. The liver tumors determined by our scheme were compared with those manually traced by a radiologist, used as the “ground truth.” Results. The study was evaluated on two datasets of 25 tumors from 16 patients. The proposed scheme obtained the mean volumetric overlap error of 27.43% and the mean percentage volume error of 15.73%. The mean of the average surface distance, the root mean square surface distance, and the maximal surface distance were 0.58 mm, 1.20 mm, and 6.29 mm, respectively. PMID:27597960

  5. 3D-nanoarchitectured Pd/Ni catalysts prepared by atomic layer deposition for the electrooxidation of formic acid

    PubMed Central

    Assaud, Loïc; Monyoncho, Evans; Pitzschel, Kristina; Allagui, Anis; Petit, Matthieu; Hanbücken, Margrit

    2014-01-01

    Summary Three-dimensionally (3D) nanoarchitectured palladium/nickel (Pd/Ni) catalysts, which were prepared by atomic layer deposition (ALD) on high-aspect-ratio nanoporous alumina templates are investigated with regard to the electrooxidation of formic acid in an acidic medium (0.5 M H2SO4). Both deposition processes, Ni and Pd, with various mass content ratios have been continuously monitored by using a quartz crystal microbalance. The morphology of the Pd/Ni systems has been studied by electron microscopy and shows a homogeneous deposition of granularly structured Pd onto the Ni substrate. X-ray diffraction analysis performed on Ni and NiO substrates revealed an amorphous structure, while the Pd coating crystallized into a fcc lattice with a preferential orientation along the [220]-direction. Surface chemistry analysis by X-ray photoelectron spectroscopy showed both metallic and oxide contributions for the Ni and Pd deposits. Cyclic voltammetry of the Pd/Ni nanocatalysts revealed that the electrooxidation of HCOOH proceeds through the direct dehydrogenation mechanism with the formation of active intermediates. High catalytic activities are measured for low masses of Pd coatings that were generated by a low number of ALD cycles, probably because of the cluster size effect, electronic interactions between Pd and Ni, or diffusion effects. PMID:24605281

  6. Liver Tumor Segmentation from MR Images Using 3D Fast Marching Algorithm and Single Hidden Layer Feedforward Neural Network.

    PubMed

    Le, Trong-Ngoc; Bao, Pham The; Huynh, Hieu Trung

    2016-01-01

    Objective. Our objective is to develop a computerized scheme for liver tumor segmentation in MR images. Materials and Methods. Our proposed scheme consists of four main stages. Firstly, the region of interest (ROI) image which contains the liver tumor region in the T1-weighted MR image series was extracted by using seed points. The noise in this ROI image was reduced and the boundaries were enhanced. A 3D fast marching algorithm was applied to generate the initial labeled regions which are considered as teacher regions. A single hidden layer feedforward neural network (SLFN), which was trained by a noniterative algorithm, was employed to classify the unlabeled voxels. Finally, the postprocessing stage was applied to extract and refine the liver tumor boundaries. The liver tumors determined by our scheme were compared with those manually traced by a radiologist, used as the "ground truth." Results. The study was evaluated on two datasets of 25 tumors from 16 patients. The proposed scheme obtained the mean volumetric overlap error of 27.43% and the mean percentage volume error of 15.73%. The mean of the average surface distance, the root mean square surface distance, and the maximal surface distance were 0.58 mm, 1.20 mm, and 6.29 mm, respectively. PMID:27597960

  7. TECHNICAL NOTE: Design and development of electromagnetic absorbers with carbon fiber composites and matching dielectric layers

    NASA Astrophysics Data System (ADS)

    Neo, C. P.; Varadan, V. K.

    2001-10-01

    Radar absorbing materials are designed and developed with carbon fibers and suitable matching layers. Complex permittivities of carbon fiber composite are predicted on the basis that the modulus of permittivity obeys a logarithmic law of mixtures and the dielectric loss tangents are related through a linear law of mixtures. Linear regression analysis performed on the data points provides the constants which are used to predict the effective permittivities of carbon fiber composite at different frequencies. Using the free space measurement system, complex permittivities of the lossy dielectric at different frequencies are obtained. These complex permittivities are used to predict the reflectivity of a thin lossy dielectric layer on carbon fiber composite substrate. The predicted results agree quite well with the measured data. It is interesting to note that the thin lossy dielectric layer, about 0.03 mm thick, has helped to reduce the reflectivity of the 5.2 mm thick carbon fiber composite considerably.

  8. Contribution of dielectric screening to the total capacitance of few-layer graphene electrodes

    DOE PAGESBeta

    Zhan, Cheng; Jiang, De-en

    2016-02-17

    We apply joint density functional theory (JDFT), which treats the electrode/electrolyte interface self-consistently, to an electric double-layer capacitor (EDLC) based on few-layer graphene electrodes. The JDFT approach allows us to quantify a third contribution to the total capacitance beyond quantum capacitance (CQ) and EDL capacitance (CEDL). This contribution arises from the dielectric screening of the electric field by the surface of the few-layer graphene electrode, and we therefore term it the dielectric capacitance (CDielec). We find that CDielec becomes significant in affecting the total capacitance when the number of graphene layers in the electrode is more than three. In conclusion,more » our investigation sheds new light on the significance of the electrode dielectric screening on the capacitance of few-layer graphene electrodes.« less

  9. Characterization of cylindrical terahertz metallic hollow waveguide with multiple dielectric layers.

    PubMed

    Sun, Bang-Shan; Tang, Xiao-Li; Zeng, Xuan; Shi, Yi-Wei

    2012-10-20

    Dielectric-coated metallic hollow waveguides (DMHW) are drawing considerable attention for their application in terahertz (THz) waveguiding. This paper theoretically analyzes the multilayer structure to reduce the transmission and bending loss of DMHW. The efficiency of THz multilayer DMHW depends on a proper selection of dielectric materials and geometrical parameters. The low-loss properties are demonstrated by studying the multilayer gold waveguides with a stack of polypropylene (PP) and Si-doped polypropylene (PP(Si)). Comparisons are made with single-layer Au/PP and Au-only waveguides. The effect of dielectric absorption is discussed in detail. It is found that low index dielectric causes more additional loss than that of high index dielectric layers. Several design considerations for the THz multilayer DMHW are pointed out by studying the effects of multilayer structure parameters with a stack of polyethylene (PE) and TiO(2)-doped polyethylene (PE(TiO2)). We conclude that the inner radius of the waveguide and the refractive indices of the dielectrics tend to be larger in order to reduce the influence of material absorption. An optimal value exists for the total number of layers when the dielectrics are absorptive. The absorption tolerances are pointed out to guarantee a smaller loss for multilayer DMHW than that of metal-only waveguide. Finally, a fabrication method for THz multilayer DMHW Ag/PE/PE(TiO2) is proposed based on co-rolling technique. PMID:23089782

  10. Mapping the 3-D extent of the Northern Lobe of the Bushveld layered mafic intrusion from geophysical data

    USGS Publications Warehouse

    Finn, Carol A.; Bedrosian, Paul A.; Cole, Janine; Khoza, Tshepo David; Webb, Susan J.

    2015-01-01

    Geophysical models image the 3D geometry of the mafic portion of the Bushveld Complex north of the Thabazimbi-Murchison Lineament (TML), critical for understanding the origin of the world's largest layered mafic intrusion and platinum group element deposits. The combination of the gravity and magnetic data with recent seismic, MT, borehole and rock property measurements powerfully constrains the models. The intrusion north of the TML is generally shallowly buried (generally <1500 m) with a modeled area of ∼160 km × ∼125 km. The modeled thicknesses are not well constrained but vary from ∼<1000 to >12,000 m, averaging ∼4000 m. A feeder, suggested by a large modeled thickness (>10,000 m) and funnel shape, for Lower Zone magmas could have originated near the intersection of NS and NE trending TML faults under Mokopane. The TML has been thought to be the feeder zone for the entire Bushveld Complex but the identification of local feeders and/or dikes in the TML in the models is complicated by uncertainties on the syn- and post-Bushveld deformation history. However, modeled moderately thick high density material near the intersection of faults within the central and western TML may represent feeders for parts of the Bushveld Complex if deformation was minimal. The correspondence of flat, high resistivity and density regions reflect the sill-like geometry of the Bushveld Complex without evidence for feeders north of Mokopane. Magnetotelluric models indicate that the Transvaal sedimentary basin underlies much of the Bushveld Complex north of the TML, further than previously thought and important because the degree of reaction and assimilation of the Transvaal rocks with the mafic magmas resulted in a variety of mineralization zones.

  11. Highly Resolved Long-term 3D Hydrological Simulation of a Forested Catchment with Litter Layer and Fractured Bedrock

    NASA Astrophysics Data System (ADS)

    Fang, Z.; Bogena, H. R.; Kollet, S. J.; Vereecken, H.

    2014-12-01

    Soil water content plays a key role in the water and energy balance in soil, vegetation and atmosphere systems. According to Wood et al. (2011) there is a grand need to increase global-scale hyper-resolution water-energy-biogeochemistry land surface modelling capabilities. However, such a model scheme should also recognize the epistemic uncertainties, as well as the nonlinearity and hysteresis in its dynamics. Unfortunately, it is not clear how to parameterize hydrological processes as a function of scale and how to test deterministic models with regard to epistemic uncertainties. In this study, high resolution long-term simulations were conducted in the highly instrumented TERENO hydrological observatory, the Wüstebach catchment. Soil hydraulic parameters were derived using inverse modeling with the Hydrus-1D model using the global optimization scheme SCE-UA and soil moisture data from a wireless soil moisture sensor network. The estimated parameters were then used for 3D simulations using the integrated parallel simulation platform ParFlow-CLM. The simulated soil water content, as well as evapotranspiration and runoff, were compared with long-term field observations to illustrate how well the model was able to reproduce the water budget dynamics. With variable model setup scenarios in boundary conditions and anisotropy of hydraulic conductivity, we investigated how lateral flow processes above the underlying fractured bedrock affects the simulation results. Furthermore, we explored the importance of the litter layer and the heterogeneity of the forest soil in the simulation of flow processes and model performance. For the analysis of spatial patterns of simulated and observed soil water content we applied the method of empirical orthogonal function (EOF). The results suggest that strong anisotropy in the hydraulic conductivity may be the reason for the fast lateral flow observed in Wüstebach. Introduction of heterogeneity in the hydraulic properties in the

  12. Stress evolution during 3D single-layer visco-elastic buckle folding: Implications for the initiation of fractures

    NASA Astrophysics Data System (ADS)

    Liu, Xiaolong; Eckert, Andreas; Connolly, Peter

    2016-06-01

    Buckle folds of sedimentary strata commonly feature a variety of different fracture sets. Some fracture sets including outer arc tensile fractures and inner arc shear fractures at the fold hinge zones are well understood by the extensional and compressional strain/stress pattern. However, other commonly observed fracture sets, including tensile fractures parallel to the fold axis, tensile fractures cutting through the limb, extensional faults at the fold hinge, and other shear fractures of various orientations in the fold limb, fail to be intuitively explained by the strain/stress regimes during the buckling process. To obtain a better understanding of the conditions for the initiation of the various fractures sets associated with single-layer cylindrical buckle folds, a 3D finite element modeling approach using a Maxwell visco-elastic rheology is utilized. The influences of three model parameters with significant influence on fracture initiation are considered: burial depth, viscosity, and permeability. It is concluded that these parameters are critical for the initiation of major fracture sets at the hinge zone with varying degrees. The numerical simulation results further show that the buckling process fails to explain most of the fracture sets occurring in the limb unless the process of erosional unloading as a post-fold phenomenon is considered. For fracture sets that only develop under unrealistic boundary conditions, the results demonstrate that their development is realistic for a perclinal fold geometry. In summary, a more thorough understanding of fractures sets associated with buckle folds is obtained based on the simulation of in-situ stress conditions during the structural development of buckle folds.

  13. Highly uniform residual layers for arrays of 3D nanoimprinted cavities in Fabry-Pérot-filter-array-based nanospectrometers

    NASA Astrophysics Data System (ADS)

    Memon, Imran; Shen, Yannan; Khan, Abdullah; Woidt, Carsten; Hillmer, Hartmut

    2016-04-01

    Miniaturized optical spectrometers can be implemented by an array of Fabry-Pérot (FP) filters. FP filters are composed of two highly reflecting parallel mirrors and a resonance cavity. Each filter transmits a small spectral band (filter line) depending on its individual cavity height. The optical nanospectrometer, a miniaturized FP-based spectrometer, implements 3D NanoImprint technology for the fabrication of multiple FP filter cavities in a single process step. However, it is challenging to avoid the dependency of residual layer (RL) thickness on the shape of the printed patterns in NanoImprint. Since in a nanospectrometer the filter cavities vary in height between neighboring FP filters and, thus, the volume of each cavity varies causing that the RL varies slightly or noticeably between different filters. This is one of the few disadvantages of NanoImprint using soft templates such as substrate conformal imprint lithography which is used in this paper. The advantages of large area soft templates can be revealed substantially if the problem of laterally inhomogeneous RLs can be avoided or reduced considerably. In the case of the nanospectrometer, non-uniform RLs lead to random variations in the designed cavity heights resulting in the shift of desired filter lines. To achieve highly uniform RLs, we report a volume-equalized template design with the lateral distribution of 64 different cavity heights into several units with each unit comprising four cavity heights. The average volume of each unit is kept constant to obtain uniform filling of imprint material per unit area. The imprint results, based on the volume-equalized template, demonstrate highly uniform RLs of 110 nm thickness.

  14. THE ONSET OF ELECTRICAL BREAKDOWN IN DUST LAYERS: II. EFFECTIVE DIELECTRIC CONSTANT AND LOCAL FIELD ENHANCEMENT

    EPA Science Inventory

    Part 1 of the work has shown that electrical breakdown in dust layers obeys Paschen's Law, but occurs at applied field values which appear too small to initiate the breakdown. In this paper the authors show how an effective dielectric constant characterizing the dust layer can be...

  15. Thickness-Dependent Dielectric Constant of Few-Layer In₂Se₃ Nanoflakes.

    PubMed

    Wu, Di; Pak, Alexander J; Liu, Yingnan; Zhou, Yu; Wu, Xiaoyu; Zhu, Yihan; Lin, Min; Han, Yu; Ren, Yuan; Peng, Hailin; Tsai, Yu-Hao; Hwang, Gyeong S; Lai, Keji

    2015-12-01

    The dielectric constant or relative permittivity (ε(r)) of a dielectric material, which describes how the net electric field in the medium is reduced with respect to the external field, is a parameter of critical importance for charging and screening in electronic devices. Such a fundamental material property is intimately related to not only the polarizability of individual atoms but also the specific atomic arrangement in the crystal lattice. In this Letter, we present both experimental and theoretical investigations on the dielectric constant of few-layer In2Se3 nanoflakes grown on mica substrates by van der Waals epitaxy. A nondestructive microwave impedance microscope is employed to simultaneously quantify the number of layers and local electrical properties. The measured ε(r) increases monotonically as a function of the thickness and saturates to the bulk value at around 6-8 quintuple layers. The same trend of layer-dependent dielectric constant is also revealed by first-principles calculations. Our results of the dielectric response, being ubiquitously applicable to layered 2D semiconductors, are expected to be significant for this vibrant research field. PMID:26575786

  16. Characteristics of Spontaneous Emission of Polarized Atoms in Metal Dielectric Multiple Layer Structures

    NASA Astrophysics Data System (ADS)

    Zhao, Li-Ming; Gu, Ben-Yuan; Zhou, Yun-Song

    2007-11-01

    The spontaneous emission (SE) progress of polarized atoms in a stratified structure of air-dielectric(D0)-metal(M)-dielectric(D1)-air can be controlled effectively by changing the thickness of the D1 layer and rotating the polarized direction of atoms. It is found that the normalized SE rate of atoms located inside the D0 layer crucially depends on the atomic position and the thickness of the D1 layer. When the atom is located near the D0-M interface, the normalized atomic SE rate as a function of the atomic position is abruptly onset for the thin D1 layer. However, with the increasing thickness of the D1 layer, the corresponding curve profile exhibits plateau and stays nearly unchanged. The substantial change of the SE rate stems from the excitation of the surface plasmon polaritons in metal-dielectric interface, and the feature crucially depends on the thickness of D1 layer. If atoms are positioned near the D0-air interface, the substantial variation of the normalized SE rate appears when rotating the polarized direction of atoms. These findings manifest that the atomic SE processes can be flexibly controlled by altering the thickness of the dielectric layer D1 or rotating the orientation of the polarization of atoms.

  17. van der Waals torque and force between dielectrically anisotropic layered media

    NASA Astrophysics Data System (ADS)

    Lu, Bing-Sui; Podgornik, Rudolf

    2016-07-01

    We analyse van der Waals interactions between a pair of dielectrically anisotropic plane-layered media interacting across a dielectrically isotropic solvent medium. We develop a general formalism based on transfer matrices to investigate the van der Waals torque and force in the limit of weak birefringence and dielectric matching between the ordinary axes of the anisotropic layers and the solvent. We apply this formalism to study the following systems: (i) a pair of single anisotropic layers, (ii) a single anisotropic layer interacting with a multilayered slab consisting of alternating anisotropic and isotropic layers, and (iii) a pair of multilayered slabs each consisting of alternating anisotropic and isotropic layers, looking at the cases where the optic axes lie parallel and/or perpendicular to the plane of the layers. For the first case, the optic axes of the oppositely facing anisotropic layers of the two interacting slabs generally possess an angular mismatch, and within each multilayered slab the optic axes may either be the same or undergo constant angular increments across the anisotropic layers. In particular, we examine how the behaviors of the van der Waals torque and force can be "tuned" by adjusting the layer thicknesses, the relative angular increment within each slab, and the angular mismatch between the slabs.

  18. van der Waals torque and force between dielectrically anisotropic layered media.

    PubMed

    Lu, Bing-Sui; Podgornik, Rudolf

    2016-07-28

    We analyse van der Waals interactions between a pair of dielectrically anisotropic plane-layered media interacting across a dielectrically isotropic solvent medium. We develop a general formalism based on transfer matrices to investigate the van der Waals torque and force in the limit of weak birefringence and dielectric matching between the ordinary axes of the anisotropic layers and the solvent. We apply this formalism to study the following systems: (i) a pair of single anisotropic layers, (ii) a single anisotropic layer interacting with a multilayered slab consisting of alternating anisotropic and isotropic layers, and (iii) a pair of multilayered slabs each consisting of alternating anisotropic and isotropic layers, looking at the cases where the optic axes lie parallel and/or perpendicular to the plane of the layers. For the first case, the optic axes of the oppositely facing anisotropic layers of the two interacting slabs generally possess an angular mismatch, and within each multilayered slab the optic axes may either be the same or undergo constant angular increments across the anisotropic layers. In particular, we examine how the behaviors of the van der Waals torque and force can be "tuned" by adjusting the layer thicknesses, the relative angular increment within each slab, and the angular mismatch between the slabs. PMID:27475386

  19. Directional Emission from Metal-Dielectric-Metal Structures: Effect of Mixed Metal Layers, Dye Location and Dielectric Thickness

    PubMed Central

    Choudhury, Sharmistha Dutta; Badugu, Ramachandram; Ray, Krishanu; Lakowicz, Joseph R.

    2015-01-01

    Metal-dielectric-metal (MDM) structures provide directional emission close to the surface normal, which offers opportunities for new design formats in fluorescence based applications. The directional emission arises due to near-field coupling of fluorophores with the optical modes present in the MDM substrate. Reflectivity simulations and dispersion diagrams provide a basic understanding of the mode profiles and the factors that affect the coupling efficiency and the spatial distribution of the coupled emission. This work reveals that the composition of the metal layers, the location of the dye in the MDM substrate and the dielectric thickness are important parameters that can be chosen to tune the color of the emission wavelength, the angle of observation, the angular divergence of the emission and the polarization of the emitted light. These features are valuable for displays and optical signage. PMID:25844110

  20. Frequency selective reflection and transmission at a layer composed of a periodic dielectric

    NASA Technical Reports Server (NTRS)

    Bertoni, Henry L.; Cheo, Li-Hsiang S.; Tamir, Theodor

    1987-01-01

    The feasibility of using a periodic dielectric layer, composed of alternating bars having dielectric constants epsilon sub 1 and epsilon sub 2, as a frequency selective subreflector in order to permit feed separation in large aperture reflecting antenna systems was examined. For oblique incidence, it is found that total transmission and total reflection can be obtained at different frequencies for proper choices of epsilon sub 1, epsilon 2, and the geometric parameters. The frequencies of total reflection and transmission can be estimated from wave phenomena occurring in a layer of uniform dielectric constant equal to the average for the periodic layers. About some of the frequencies of total transmission, the bandwidth for 90% transmission is found to be 40%. However, the bandwidth for 90% reflection is always found to be much narrower; the greatest value found being 2.5%.

  1. Effect of Layer Thickness and Printing Orientation on Mechanical Properties and Dimensional Accuracy of 3D Printed Porous Samples for Bone Tissue Engineering

    PubMed Central

    Farzadi, Arghavan; Solati-Hashjin, Mehran; Asadi-Eydivand, Mitra; Abu Osman, Noor Azuan

    2014-01-01

    Powder-based inkjet 3D printing method is one of the most attractive solid free form techniques. It involves a sequential layering process through which 3D porous scaffolds can be directly produced from computer-generated models. 3D printed products' quality are controlled by the optimal build parameters. In this study, Calcium Sulfate based powders were used for porous scaffolds fabrication. The printed scaffolds of 0.8 mm pore size, with different layer thickness and printing orientation, were subjected to the depowdering step. The effects of four layer thicknesses and printing orientations, (parallel to X, Y and Z), on the physical and mechanical properties of printed scaffolds were investigated. It was observed that the compressive strength, toughness and Young's modulus of samples with 0.1125 and 0.125 mm layer thickness were more than others. Furthermore, the results of SEM and μCT analyses showed that samples with 0.1125 mm layer thickness printed in X direction have more dimensional accuracy and significantly close to CAD software based designs with predefined pore size, porosity and pore interconnectivity. PMID:25233468

  2. Layered nano-gratings by electron beam writing to form 3-level diffractive optical elements for 3D phase-offset holographic lithography.

    PubMed

    Yuan, Liang Leon; Herman, Peter R

    2015-12-21

    A multi-level nanophotonic structure is a major goal in providing advanced optical functionalities as found in photonic crystals and metamaterials. A three-level nano-grating phase mask has been fabricated in an electron-beam resist (ma-N) to meet the requirement of holographic generation of a diamond-like 3D nanostructure in photoresist by a single exposure step. A 2D mask with 600 nm periodicity is presented for generating first order diffracted beams with a preferred π/2 phase shift on the X- and Y-axes and with sufficient 1(st) order diffraction efficiency of 3.5% at 800 nm wavelength for creating a 3D periodic nanostructure in SU-8 photoresist. The resulting 3D structure is anticipated to provide an 8% complete photonic band gap (PBG) upon silicon inversion. A thin SiO2 layer was used to isolate the grating layers and multiple spin-coating steps served to planarize the final resist layer. A reversible soft coating (aquaSAVE) was introduced to enable SEM inspection and verification of each insulating grating layer. This e-beam lithographic method is extensible to assembling multiple layers of a nanophotonic structure. PMID:26568395

  3. Layered nano-gratings by electron beam writing to form 3-level diffractive optical elements for 3D phase-offset holographic lithography

    NASA Astrophysics Data System (ADS)

    Yuan, Liang (Leon); Herman, Peter R.

    2015-11-01

    A multi-level nanophotonic structure is a major goal in providing advanced optical functionalities as found in photonic crystals and metamaterials. A three-level nano-grating phase mask has been fabricated in an electron-beam resist (ma-N) to meet the requirement of holographic generation of a diamond-like 3D nanostructure in photoresist by a single exposure step. A 2D mask with 600 nm periodicity is presented for generating first order diffracted beams with a preferred π/2 phase shift on the X- and Y-axes and with sufficient 1st order diffraction efficiency of 3.5% at 800 nm wavelength for creating a 3D periodic nanostructure in SU-8 photoresist. The resulting 3D structure is anticipated to provide an 8% complete photonic band gap (PBG) upon silicon inversion. A thin SiO2 layer was used to isolate the grating layers and multiple spin-coating steps served to planarize the final resist layer. A reversible soft coating (aquaSAVE) was introduced to enable SEM inspection and verification of each insulating grating layer. This e-beam lithographic method is extensible to assembling multiple layers of a nanophotonic structure.

  4. Improvement of Resistive Random Access Memory Device Performance via Embedding of Low-K Dielectric Layer.

    PubMed

    Jang, Sung Hwan; Ryu, Ju Tae; Jung, Hyun Soo; Kim, Tae Whan

    2016-02-01

    The switching mechanisms of resistive random access memories (ReRAMs) were strongly related to the formation and rupture of conduction filaments (CFs) in the transition metal oxide (TMO) layer. The novel method approached to enhance the electrical characteristics of ReRAMs by introducing of the local insertion of the low-k dielectric layer inside the TMO layer. Simulation results showed that the insertion of the low-k dielectric layer in the TMO layer reduced the switching volume and the generation of CFs. The large variation of resistive switching properties was caused by the stochastic characteristics of the CFs, which was involved in switching by generation and rupture. The electrical characteristics of the novel ReRAMs exhibited a low reset current of below 20 microA, the high uniformity of the resistive switching, and the narrow variation of the resistance for the high resistance state. PMID:27433626

  5. Dielectric screening of excitons and trions in single-layer MoS2.

    PubMed

    Lin, Yuxuan; Ling, Xi; Yu, Lili; Huang, Shengxi; Hsu, Allen L; Lee, Yi-Hsien; Kong, Jing; Dresselhaus, Mildred S; Palacios, Tomás

    2014-10-01

    Photoluminescence (PL) properties of single-layer MoS2 are indicated to have strong correlations with the surrounding dielectric environment. Blue shifts of up to 40 meV of exciton or trion PL peaks were observed as a function of the dielectric constant of the environment. These results can be explained by the dielectric screening effect of the Coulomb potential; based on this, a scaling relationship was developed with the extracted electronic band gap and exciton and trion binding energies in good agreement with theoretical estimations. It was also observed that the trion/exciton intensity ratio can be tuned by at least 1 order of magnitude with different dielectric environments. Our findings are helpful to better understand the tightly bound exciton properties in strongly quantum-confined systems and provide a simple approach to the selective and separate generation of excitons or trions with potential applications in excitonic interconnects and valleytronics. PMID:25216267

  6. Seeding atomic layer deposition of high-k dielectric on graphene with ultrathin poly(4-vinylphenol) layer for enhanced device performance and reliability

    NASA Astrophysics Data System (ADS)

    Cheol Shin, Woo; Yong Kim, Taek; Sul, Onejae; Jin Cho, Byung

    2012-07-01

    We demonstrate that ultrathin poly(4-vinylphenol) (PVP) acts as an effective organic seeding layer for atomic layer deposition (ALD) of high-k dielectric on large-scale graphene fabricated by chemical vapor deposition (CVD). While identical ALD conditions result in incomplete and rough dielectric deposition on CVD graphene, the reactive groups provided by the PVP seeding layer yield conformal and pinhole-free dielectric films throughout the large-scale graphene. Top-gate graphene field effect transistors fabricated with the high quality, PVP-seeded Al2O3 gate dielectric show superior carrier mobility and enhanced reliability performance, which are desirable for graphene nanoelectronics.

  7. Molecular Layer-seeded Ultra-thin Top-gate Dielectrics for High Transconductance Graphene Transistors

    NASA Astrophysics Data System (ADS)

    Sangwan, Vinod; Jariwala, Deep; Karmel, Hunter; Alaboson, Justice; Lauhon, Lincoln; Marks, Tobin; Hersam, Mark

    2012-02-01

    The potential of graphene in integrated analog and digital circuits can only be fully realized through incorporation of ultra-thin gate dielectrics to enable large-scale small-channel graphene field-effect transistors (GFETs). Atomic-layer deposition (ALD) is a viable technique to fabricate gate-dielectrics, however, it requires a seeding layer on otherwise inert graphene. Here, we demonstrate a single molecule thick perylene-3,4,9,10-tetracarboxylic dianhydride overlayer as an effective seeding layer to grow high-κ Al2O3 on mechanically exfoliated graphene for high-performance GFETs. Using an ultra-thin (< 1nm) seeding layer, in contrast to polymer films (5-10 nm), we demonstrate fabrication of the thinnest ALD-grown gate-dielectric (4 nm) reported to date in top-gated GFETs. This yields high performance GFETs with the intrinsic transconductance parameter approaching 2.4 mS and the field-effect mobility ˜3000 cm^2/Vs. We also demonstrate generalization of this molecular layer seeded-ALD growth method to higher- κ gate dielectrics, yielding further enhanced GFET transconductance for possible application to radio-frequency circuits.

  8. Zinc oxide nanowire-poly(methyl methacrylate) dielectric layers for polymer capacitive pressure sensors.

    PubMed

    Chen, Yan-Sheng; Hsieh, Gen-Wen; Chen, Shih-Ping; Tseng, Pin-Yen; Wang, Cheng-Wei

    2015-01-14

    Polymer capacitive pressure sensors based on a dielectric composite layer of zinc oxide nanowire and poly(methyl methacrylate) show pressure sensitivity in the range of 2.63 × 10(-3) to 9.95 × 10(-3) cm(2) gf(-1). This represents an increase of capacitance change by as much as a factor of 23 over pristine polymer devices. An ultralight load of only 10 mg (corresponding to an applied pressure of ∼0.01 gf cm(-2)) can be clearly recognized, demonstrating remarkable characteristics of these nanowire-polymer capacitive pressure sensors. In addition, optical transmittance of the dielectric composite layer is approximately 90% in the visible wavelength region. Their low processing temperature, transparency, and flexible dielectric film makes them a highly promising means for flexible touching and pressure-sensing applications. PMID:25494204

  9. Control of Evaporation Behavior of an Inkjet-Printed Dielectric Layer Using a Mixed-Solvent System

    NASA Astrophysics Data System (ADS)

    Yang, Hak Soon; Kang, Byung Ju; Oh, Je Hoon

    2016-01-01

    In this study, the evaporation behavior and the resulting morphology of inkjet-printed dielectric layers were controlled using a mixed-solvent system to fabricate uniform poly-4-vinylphenol (PVP) dielectric layers without any pinholes. The mixed-solvent system consisted of two different organic solvents: 1-hexanol and ethanol. The effects of inkjet-printing variables such as overlap condition, substrate temperature, and different printing sequences (continuous and interlacing printing methods) on the inkjet-printed dielectric layer were also investigated. Increasing volume fraction of ethanol (VFE) is likely to reduce the evaporation rate gradient and the drying time of the inkjet-printed dielectric layer; this diminishes the coffee stain effect and thereby improves the uniformity of the inkjet-printed dielectric layer. However, the coffee stain effect becomes more severe with an increase in the substrate temperature due to the enhanced outward convective flow. The overlap condition has little effect on the evaporation behavior of the printed dielectric layer. In addition, the interlacing printing method results in either a stronger coffee stain effect or wavy structures of the dielectric layers depending on the VFE of the PVP solution. All-inkjet-printed capacitors without electrical short circuiting can be successfully fabricated using the optimized PVP solution (VFE = 0.6); this indicates that the mixed-solvent system is expected to play an important role in the fabrication of high-quality inkjet-printed dielectric layers in various printed electronics applications.

  10. DNA-nucleobases: gate dielectric/passivation layer for flexible GFET-based sensor applications

    NASA Astrophysics Data System (ADS)

    Williams, Adrienne D.; Ouchen, Fahima; Kim, Steve S.; Elhamri, Said; Naik, Rajesh R.; Grote, James

    2015-09-01

    The main goal of this research was to maintain the bulk charge carrier mobility of graphene, after deposition of the gate dielectric layer used for making transistor devices. The approach was introducing a thin film of deoxyribonucleic acid (DNA) nucleobase purine guanine, deposited by physical vapor deposition (PVD), onto layers of graphene that were transferred onto various flexible substrates. Several test platforms were fabricated with guanine as a standalone gate dielectric, as the control, and guanine as a passivation layer between the graphene and PMMA. It was found that the bulk charge carrier mobility of graphene was best maintained and most stable using guanine as a passivation layer between the graphene and PMMA. Other transport properties, such as charge carrier concentration, conductivity type and electrical resistivity were investigated as well. This is an important first step to realizing high performance graphene-based transistors that have potential use in bio and environmental sensors, computer-processing and electronics.

  11. Electrical Double Layer Capacitance in a Graphene-embedded Al2O3 Gate Dielectric

    PubMed Central

    Ki Min, Bok; Kim, Seong K.; Jun Kim, Seong; Ho Kim, Sung; Kang, Min-A; Park, Chong-Yun; Song, Wooseok; Myung, Sung; Lim, Jongsun; An, Ki-Seok

    2015-01-01

    Graphene heterostructures are of considerable interest as a new class of electronic devices with exceptional performance in a broad range of applications has been realized. Here, we propose a graphene-embedded Al2O3 gate dielectric with a relatively high dielectric constant of 15.5, which is about 2 times that of Al2O3, having a low leakage current with insertion of tri-layer graphene. In this system, the enhanced capacitance of the hybrid structure can be understood by the formation of a space charge layer at the graphene/Al2O3 interface. The electrical properties of the interface can be further explained by the electrical double layer (EDL) model dominated by the diffuse layer. PMID:26530817

  12. Electric-field noise above a thin dielectric layer on metal electrodes

    NASA Astrophysics Data System (ADS)

    Kumph, Muir; Henkel, Carsten; Rabl, Peter; Brownnutt, Michael; Blatt, Rainer

    2016-02-01

    The electric-field noise above a layered structure composed of a planar metal electrode covered by a thin dielectric is evaluated and it is found that the dielectric film considerably increases the noise level, in proportion to its thickness. Importantly, even a thin (mono) layer of a low-loss dielectric can enhance the noise level by several orders of magnitude compared to the noise above a bare metal. Close to this layered surface, the power spectral density of the electric field varies with the inverse fourth power of the distance to the surface, rather than with the inverse square, as it would above a bare metal surface. Furthermore, compared to a clean metal, where the noise spectrum does not vary with frequency (in the radio-wave and microwave bands), the dielectric layer can generate electric-field noise which scales in inverse proportion to the frequency. For various realistic scenarios, the noise levels predicted from this model are comparable to those observed in trapped-ion experiments. Thus, these findings are of particular importance for the understanding and mitigation of unwanted heating and decoherence in miniaturized ion traps.

  13. A novel method of fabricating laminated silicone stack actuators with pre-strained dielectric layers

    NASA Astrophysics Data System (ADS)

    Hinitt, Andrew D.; Conn, Andrew T.

    2014-03-01

    In recent studies, stack based Dielectric Elastomer Actuators (DEAs) have been successfully used in haptic feedback and sensing applications. However, limitations in the fabrication method, and materials used to con- struct stack actuators constrain their force and displacement output per unit volume. This paper focuses on a fabrication process enabling a stacked elastomer actuator to withstand the high tensile forces needed for high power applications, such as mimetics for mammalian muscle contraction (i.e prostheses), whilst requiring low voltage for thickness-mode contractile actuation. Spun elastomer layers are bonded together in a pre-strained state using a conductive adhesive filler, forming a Laminated Inter-Penetrating Network (L-IPN) with repeatable and uniform electrode thickness. The resulting structure utilises the stored strain energy of the dielectric elas- tomer to compress the cured electrode composite material. The method is used to fabricate an L-IPN example, which demonstrated that the bonded L-IPN has high tensile strength normal to the lamination. Additionally, the uniformity and retained dielectric layer pre-strain of the L-IPN are confirmed. The described method is envisaged to be used in a semi-automated assembly of large-scale multi-layer stacks of pre-strained dielectric layers possessing a tensile strength in the range generated by mammalian muscle.

  14. Linear and nonlinear instability and ligament dynamics in 3D laminar two-layer liquid/liquid flows

    NASA Astrophysics Data System (ADS)

    Ó Náraigh, Lennon; Valluri, Prashant; Scott, David; Bethune, Iain; Spelt, Peter

    2013-11-01

    We consider the linear and nonlinear stability of two-phase density-matched but viscosity contrasted fluids subject to laminar Poiseuille flow in a channel, paying particular attention to the formation of three-dimensional waves. The Orr-Sommerfeld-Squire analysis is used along with DNS of the 3D two-phase Navier-Stokes equations using our newly launched TPLS Solver (http://edin.ac/10cRKzS). For the parameter regimes considered, we demonstrate the existence of two distinct mechanisms whereby 3D waves enter the system, and dominate at late time. There exists a direct route, whereby 3D waves are amplified by the standard linear mechanism; for certain parameter classes, such waves grow at a rate less than but comparable to that of most-dangerous two-dimensional mode. Additionally, there is a weakly nonlinear route, whereby a purely spanwise wave couples to a streamwise mode and grows exponentially. We demonstrate these mechanisms in isolation and in concert. Consideration is also given to the ultimate state of these waves: persistent three-dimensional nonlinear waves are stretched and distorted by the base flow, thereby producing regimes of ligaments, ``sheets,'' or ``interfacial turbulence.'' HECToR RAP/dCSE Project e174, HPC-Europa 2.

  15. Building continental-scale 3D subsurface layers in the Digital Crust project: constrained interpolation and uncertainty estimation.

    NASA Astrophysics Data System (ADS)

    Yulaeva, E.; Fan, Y.; Moosdorf, N.; Richard, S. M.; Bristol, S.; Peters, S. E.; Zaslavsky, I.; Ingebritsen, S.

    2015-12-01

    The Digital Crust EarthCube building block creates a framework for integrating disparate 3D/4D information from multiple sources into a comprehensive model of the structure and composition of the Earth's upper crust, and to demonstrate the utility of this model in several research scenarios. One of such scenarios is estimation of various crustal properties related to fluid dynamics (e.g. permeability and porosity) at each node of any arbitrary unstructured 3D grid to support continental-scale numerical models of fluid flow and transport. Starting from Macrostrat, an existing 4D database of 33,903 chronostratigraphic units, and employing GeoDeepDive, a software system for extracting structured information from unstructured documents, we construct 3D gridded fields of sediment/rock porosity, permeability and geochemistry for large sedimentary basins of North America, which will be used to improve our understanding of large-scale fluid flow, chemical weathering rates, and geochemical fluxes into the ocean. In this talk, we discuss the methods, data gaps (particularly in geologically complex terrain), and various physical and geological constraints on interpolation and uncertainty estimation.

  16. PHYSICAL FOUNDATIONS OF QUANTUM ELECTRONICS: Multiple reflection method for electromagnetic waves in layered dielectric structures

    NASA Astrophysics Data System (ADS)

    Morozov, G. V.; Maev, R. G.; Drake, G. W. F.

    2001-09-01

    Reflection and transmission of a plane electromagnetic wave propagating in a layered dielectric structure with an arbitrary number of layers of various thicknesses are investigated. For the general case of oblique incidence of the wave on this structure, the reflection and transmission coefficients are calculated for both TE and TM waves using a multiple reflection method. An algorithm to apply the obtained formulas for numerical and analytical calculations is suggested.

  17. Syntheses, crystal structures and properties of two unusual pillared-layer 3d-4f Ln-Cu heterometallic coordination polymers

    SciTech Connect

    Fan Leqing; Wu Jihuai; Huang Yunfang

    2011-09-15

    Two unusual pillared-layer 3d-4f Ln-Cu heterometallic coordination polymers, {l_brace}[Ln{sub 2}Cu{sub 5}Br{sub 4}(IN){sub 7}(H{sub 2}O){sub 6}].H{sub 2}O{r_brace}{sub n} (Ln=Eu (1) and Gd (2), HIN=isonicotinic acid), have been synthesized under hydrothermal conditions, and characterized by elemental analysis, IR, thermal analysis and single-crystal X-ray diffraction. The structure determination reveals that 1 and 2 are isostructural and feature a novel three-dimensional pillared-layer hetrometallic structure built upon the linkages of one-dimensional (1D) linear Ln-carboxylate chains, zero-dimensional (0D) Ln-carboxylate Ln{sub 2}(IN){sub 8} dimers, rare 1D zigzag [Cu{sub 5}Br{sub 4}]{sub n} inorganic chains and IN{sup -} pillars. In both 3D structures, there are Ln-carboxylate layers resulted from the connections of 1D Ln-carboxylate chains and 0D Ln{sub 2}(IN){sub 8} dimers through O-H...O hydrogen bondings. The luminescent properties of 1 have been investigated. The magnetic properties of 1 and 2 have also been studied. - Graphical abstract: Two unusual pillared-layer Eu (Gd)-Cu heterometallic coordination polymers have been hydrothermally synthesized. The luminescent properties of Eu-Cu compound and magnetic properties of both compounds are investigated. Highlights: > Two unusual 3D pillared-layer Eu (Gd)-Cu heterometallic coordination polymers have been synthesized. > 1D and 0D Ln-carboxylate motifs construct layers by O-H...O hydrogen bondings. > In both the structures, there are rare 1D zigzag Cu/Br inorganic chains. > Luminescent properties of Eu-Cu compound and magnetic properties of both the compounds are investigated.

  18. Process for 3D chip stacking

    DOEpatents

    Malba, Vincent

    1998-01-01

    A manufacturable process for fabricating electrical interconnects which extend from a top surface of an integrated circuit chip to a sidewall of the chip using laser pantography to pattern three dimensional interconnects. The electrical interconnects may be of an L-connect or L-shaped type. The process implements three dimensional (3D) stacking by moving the conventional bond or interface pads on a chip to the sidewall of the chip. Implementation of the process includes: 1) holding individual chips for batch processing, 2) depositing a dielectric passivation layer on the top and sidewalls of the chips, 3) opening vias in the dielectric, 4) forming the interconnects by laser pantography, and 5) removing the chips from the holding means. The process enables low cost manufacturing of chips with bond pads on the sidewalls, which enables stacking for increased performance, reduced space, and higher functional per unit volume.

  19. Process for 3D chip stacking

    DOEpatents

    Malba, V.

    1998-11-10

    A manufacturable process for fabricating electrical interconnects which extend from a top surface of an integrated circuit chip to a sidewall of the chip using laser pantography to pattern three dimensional interconnects. The electrical interconnects may be of an L-connect or L-shaped type. The process implements three dimensional (3D) stacking by moving the conventional bond or interface pads on a chip to the sidewall of the chip. Implementation of the process includes: (1) holding individual chips for batch processing, (2) depositing a dielectric passivation layer on the top and sidewalls of the chips, (3) opening vias in the dielectric, (4) forming the interconnects by laser pantography, and (5) removing the chips from the holding means. The process enables low cost manufacturing of chips with bond pads on the sidewalls, which enables stacking for increased performance, reduced space, and higher functional per unit volume. 3 figs.

  20. Thickness Reconstruction of Layers by 3D Geometrical Model to Characterize Caledonian Tectonic Complex and Data in Latvia

    NASA Astrophysics Data System (ADS)

    Ukass, J.; Saks, T.; Popovs, K.

    2012-04-01

    In present study we attempt to verify the 3D geological model, which has been built on a variety of heterogeneous data sources for the Baltic Basin (BB). Data describing the displacement along the faults and associated thickness changes of the syntectonic strata is sparse and reflects only regional relevance (Brangulis & Konsins 2002). Borehole logs provide most reliable and comprehensive data source for reconstructing the structural geology of the Latvia sedimentary cover as sufficient quality seismic data is available only for the local scale structures. Based on the thickness analysis of the boreholes rough resolution 3D geological tectonic block model was developed to deconstruct the geological structure of the Latvia Caledonian sedimentary sequence. MOSYS modeling system was used for the geological structure modeling, developed within the PUMA project (Sennikovs et al, 2011). Algorithmic genetic approach was applied to interpolate data of well logs as strata volume and sequentially to reconstruct the post-deformation situation. This approach allows modifying model construction in any step and all processes are fully documented and are repeatable. Geometrical model consists of 33 tectonic blocks bordered by the faults which were distributed by interpreting displacement amount of the blocks along the faults providing an opportunity to characterize common tectonic evolution. The study results indicate insignificant thickness change of the Ordovician and Silurian strata along the faults suggesting that major slip event along the faults occurred during the late Silurian and early Devonian, and some secondary fault reactivation during the middle Devonian Narva time. Uplift of the territory during this time is confirmed by the presence of the regional unconformity. Constructed rough resolution 3D geometrical model suggests shortening along the horizontal axis approximately 10 - 20% but most of the shortening has occurred in the central-west part of Latvia where it

  1. Strongly enhanced mode selection in a thin dielectric-coated layered microcavity laser

    NASA Astrophysics Data System (ADS)

    Moon, Hee-Jong; Kang, Dong-Yun

    2007-06-01

    Strong mode selection through an enhanced interferential coupling effect was observed in a thin dielectric-coated layered cylindrical microcavity laser. The strong coupling effect was induced owing to an enhanced reflectivity of around 50% at the dielectric-coated inner boundary of a fused silica capillary filled with a dye-doped liquid. At an optimized coating thickness of about 0.4 μm, the lasing peaks appeared only at the wavelengths corresponding to the constructive interference condition, whereas those from a bare capillary were weakly modulated.

  2. Properties of atomic layer deposited dielectrics for AlGaN/GaN device passivation

    NASA Astrophysics Data System (ADS)

    Ramanan, Narayanan; Lee, Bongmook; Kirkpatrick, Casey; Suri, Rahul; Misra, Veena

    2013-07-01

    In order to minimize ac-dc dispersion, reduce gate leakage and maximize ac transconductance, there is a critical need to identify optimal interfaces, low-k passivation dielectrics and high-k gate dielectrics. In this paper, an investigation of different atomic layer deposited (ALD) passivation dielectrics on AlGaN/GaN-based hetero-junction field effect transistors (HFETs) was performed. Angle-resolved x-ray photoelectron spectroscopy revealed that HCl/HF and NH4OH cleans resulted in a reduction of native oxide and carbon levels at the GaN surface. The role of high temperature anneals, following the ALD, on the effectiveness of passivation was also explored. Gate-lag measurements on HFETs passivated with a thin ALD high-k Al2O3 or HfAlO layer capped with a thick plasma enhanced chemical vapor deposited (PECVD) low-k SiO2 layer, annealed at 600-700 °C, were found to be as good as or even better than those with conventional PECVD silicon nitride passivation. Further, it was observed that different passivation dielectric stacks required different anneal temperatures for improved gate-lag behavior compared to the as-deposited case.

  3. Effect of the control of global planarity of intermetal dielectric layers on the lithographic process window

    NASA Astrophysics Data System (ADS)

    Keysar, Shani; Markowitz, Leah; Ben-Gigi, Corin; Tweg, Rama; Margalit-Ilovich, Ayelet; Kepten, Avishai; Wachs, Amir; Shaviv, Roey

    1999-06-01

    The sensitivity of lithographic process window to global planarity of the inter metal dielectric layers is established in this work. The inter metal dielectric layers, between the metal layers, were prepared by utilizing the H2O2/SiH4 chemistry known as the 'Advanced Planarity Layer (APL)'. Four degrees of global planarity were tested within the APL process window, utilizing different H2O2 stabilization pressures. SEM cross sections were used to determine the degree of planarity in the CMOS product and at lithographic test structures. The lithographic process window and the effect of the stepper leveling system were defined for typical high and low topographies. The results how a strong link between the lithographic process window to degree of global planarity of the APL. Good global planarity enlarged depth of focus and energy latitude, allowing a wider lithographic process window. Also, in cases of improved APL planarity, the stepper leveling system had only a limited contribution to a lithographic process window. This control over the global planarity of the inter metal dielectric layers and the wide lithographic process window that results eliminate the need for CMP at 0.5 (mu) technology.

  4. Gigahertz Dielectric Polarization of Substitutional Single Niobium Atoms in Defective Graphitic Layers.

    PubMed

    Zhang, Xuefeng; Guo, Junjie; Guan, Pengfei; Qin, Gaowu; Pennycook, Stephen J

    2015-10-01

    We synthesize two Nb/C composites with an order of magnitude difference in the density of single niobium atoms substituted into defective graphitic layers. The concentration and sites of single Nb atoms are identified using aberration-corrected scanning transmission electron microscopy and density functional theory. Comparing the experimental complex permittivity spectra reveals that a representative dielectric resonance at ∼16  GHz originates from the intrinsic polarization of single Nb atom sites, which is confirmed by theoretical simulations. The single-atom dielectric resonance represents the physical limit of the electromagnetic response of condensed matter, and thus might open up a new avenue for designing electromagnetic wave absorption materials. Single-atom resonance also has important implications in understanding the correlation between the macroscopic dielectric behaviors and the atomic-scale structural origin. PMID:26551823

  5. 3D Global PIC simulation of Alfvenic transition layers at the cusp outer boundary during IMF rotations from north to south

    NASA Astrophysics Data System (ADS)

    Cai, D. S.; Lembege, B.; Esmaeili, A.; Nishikawa, K.

    2013-12-01

    Statistical experimental observations of the cusp boundaries from CLUSTER mission made by Lavraud et al. (2005) have clearly evidenced the presence of a transition layer inside the magnetosheath near the outer boundary of the cusp. This layer characterized by Log(MA)~ 1 allows a transition from super-Alfvenic to sub-Alfvenic bulk flow from the exterior to the interior side of the outer cusp and has been mainly observed experimentally under northward interplanetary magnetic field (IMF). The role of this layer is important in order to understand the flow variations (and later the entry and precipitation of particles) when penetrating the outer boundary of the cusp. In order to analyze this layer, a large 3D PIC simulation of the global solar wind-terrestrial magnetosphere interaction have been performed, and the attention has been focused on the cusp region and its nearby surrounding during IMF rotation from north to south. Present results retrieve quite well the presence of this layer within the meridian plane for exactly northward IMF, but its location differs in the sense that it is located slightly below the X reconnection region associated to the nearby magnetopause (above the outer boundary of the cusp). In order to clarify this question, an extensive study has been performed as follows: (i) a 3D mapping of this transition layer in order to analyze more precisely the thickness, the location and the spatial extension of this layer on the magnetosphere flanks for a fixed Northward IMF configuration; (ii) a parametric study in order to analyze the impact of the IMF rotation from north to south on the persistence and the main features of this transition layer. The locations of this transition layer slightly radially expand and shrink during the IMF rotation and the thickness of the layer increases during the rotation. We show how these transition layers render the flow from super to sub Alfvenic and allow the particles enter into the magnetic cusp region. Alfven

  6. Assessment of a 3-D boundary layer code to predict heat transfer and flow losses in a turbine

    NASA Technical Reports Server (NTRS)

    Anderson, O. L.

    1984-01-01

    Zonal concepts are utilized to delineate regions of application of three-dimensional boundary layer (DBL) theory. The zonal approach requires three distinct analyses. A modified version of the 3-DBL code named TABLET is used to analyze the boundary layer flow. This modified code solves the finite difference form of the compressible 3-DBL equations in a nonorthogonal surface coordinate system which includes coriolis forces produced by coordinate rotation. These equations are solved using an efficient, implicit, fully coupled finite difference procedure. The nonorthogonal surface coordinate system is calculated using a general analysis based on the transfinite mapping of Gordon which is valid for any arbitrary surface. Experimental data is used to determine the boundary layer edge conditions. The boundary layer edge conditions are determined by integrating the boundary layer edge equations, which are the Euler equations at the edge of the boundary layer, using the known experimental wall pressure distribution. Starting solutions along the inflow boundaries are estimated by solving the appropriate limiting form of the 3-DBL equations.

  7. Neutron powder diffraction study of the layer organic-inorganic hybrid iron(II) methylphosphonate-hydrate, Fe[(CD 3PO 3)(D 2O)

    NASA Astrophysics Data System (ADS)

    Léone, Philippe; Bellitto, Carlo; Bauer, Elvira M.; Righini, Guido; André, Gilles; Bourée, Françoise

    2008-11-01

    The crystal and magnetic structures of the hybrid organic-inorganic layer compound Fe[(CD 3PO 3)(D 2O)] have been studied by neutron powder diffraction as a function of temperature down to 1.5 K. The neutron diffraction pattern recorded at 200 K shows that the fully deuterated compound crystallizes in one of the two known forms of the undeuterated Fe[(CH 3PO 3)(H 2O)]. The crystal structure is orthorhombic, space group Pmn2 1, with the following unit-cell parameters: a=5.7095(1) Å, b=8.8053(3) Å and c=4.7987(1) Å; Z=2. The crystal structure remains unchanged on cooling from 200 to 1.5 K. Moreover, at low temperature, Fe[(CD 3PO 3)(D 2O)] shows a commensurate magnetic structure ( k=(0,0,0)). As revealed by bulk susceptibility measurements on Fe[(CH 3PO 3)(H 2O)], the magnetic structure corresponds to a canted antiferromagnet with a critical temperature TN=25 K. Neutron powder diffraction reveals that below TN=23.5 K the iron magnetic moments in Fe[(CD 3PO 3)(D 2O)] are antiferromagnetically coupled and oriented along the b-axis, perpendicular to the inorganic layers. No ferromagnetic component is observable in the neutron powder diffraction experiment, due to its too small value (<0.1 μB).

  8. Plasmon-induced efficiency enhancement on dye-sensitized solar cell by a 3D TNW-AuNP layer.

    PubMed

    Yen, Yin-Cheng; Chen, Po-Hung; Chen, Jing-Zhi; Chen, Jau-An; Lin, Kuan-Jiuh

    2015-01-28

    A new 3D TNW-AuNP plasmonic electrode consists of antireflective (AR) TiO2 nanowires (TNWs) (∼600 nm thickness) serving as light-harvesting antennae coupling with Au nanoparticles (NPs). A huge red-shift of 55 nm is observed in surface plasmon spectra for the Au (11 nm) plasmonic electrode that has 11 nm size Au NPs, whereby (111) lattice planes have a specific bonding with the TiO2 (101) planes. Remarkable red-shift is mainly attributed to the localized electric field improvement resulting from the plasmonic coupling effect between the Au NPs and the Au-TiO2 hybrids. After TiCl4 treatment, this favorable Au (11 nm) nanostructure takes advantage of harvesting photons to increase the conversion efficiency of dye-sensitized solar cells (DSSCs) from 6.25% to 9.73%. PMID:25548958

  9. Electroless nickel alloy deposition on SiO2 for application as a diffusion barrier and seed layer in 3D copper interconnect technology.

    PubMed

    Kim, Tae-Yoo; Son, Hwa-Jin; Lim, Seung-Kyu; Song, Young-Il; Park, Hwa-Sun; Suh, Su-Jeong

    2014-12-01

    Electroless Ni-P films were investigated with the aim of application as barrier and seed layers in 3D interconnect technology. Different shapes of blind-via holes were fabricated with a deep reactive ion etcher and SiO2 formed on these holes as an insulating layer. The surface of the substrate has been made hydrophilic by O2 plasma treatment with 100 W of power for 20 min. Electroless Ni-P films were deposited as both a diffusion barrier and a seed layer for Cu filling process. Prior to plating, substrates were activated in a palladium chloride solution after sensitization in a tin chloride solution with various conditions in order to deposit uniform films in TSV. After the formation of the electroless barrier layer, electro Cu was plated directly on the barrier layer. Ni-P films fabricated in blind-via holes were observed by scanning electron microscope. Energy dispersive spectroscopy line scanning was carried out for evaluating the diffusion barrier properties of the Ni-P films. The electroless Ni-P layer worked well as a Cu diffusion barrier until 300 degrees C. However, Cu ions diffused into barrier layer when the annealing temperature increases over 400 degrees C. PMID:25971093

  10. Nonorthogonal {{sp}}^{3}{{d}}^{5} tight-binding parameterization of single-layer phosphorene under biaxial strain and application to FETs

    NASA Astrophysics Data System (ADS)

    Lee, Jaehyun; Seo, Jumbeom; Oh, Jung Hyun; Shin, Mincheol

    2016-06-01

    This paper presents a new set of {{sp}}3{{d}}5 tight-binding (TB) parameters for single-layer phosphorene within the Naval Research Laboratory (NRL) scheme. For this, we develop the numerical algorithm to find the NRL TB parameters fitted to ab initio results. It is shown that the proposed NRL TB parameters successfully reproduce the band structure of a single-layer phosphorene, and even under biaxial or uniaxial strain, they appropriately describe the effects, such as modification of anisotropic effective masses and band gap. Via the top-of-the-barrier model, we also investigate the performance of single-layer phosphorene FETs under biaxial strain with the NRL TB Hamiltonian and find that the results are well in accordance with those of previous studies.

  11. Interfacial properties of germanium nitride dielectric layers in germanium

    NASA Astrophysics Data System (ADS)

    Meiners, L. G.

    The first year's effort on this project has been primarily devoted to the design and construction of a low-pressure chemical vapor deposition system for growth of the germanium nitride layers. The gas manifold layout is shown schematically, as is the reactor assembly, and the vacuum pumping assembly. The generator-cavity system is capable of delivering 0-600 W of microwave power at 2.45 GHz. The power generating section has been constructed from components contained in a portable home microwave oven and the cavity was assembled from easily machinable pieces. The cw magnetron source was mounted directly on a cylindrical microwave cavity. The plasma was contained in an on-axis 20-mm o.d. quartz tube. Design tradeoffs and operating information are discussed.

  12. Improved nonlinear slot waveguides using dielectric buffer layers: properties of TM waves.

    PubMed

    Elsawy, Mahmoud M R; Renversez, Gilles

    2016-04-01

    We propose an improved version of the symmetric metal slot waveguides with a Kerr-type nonlinear dielectric core adding linear dielectric buffer layers between the metal regions and the core. Using a finite element method to compute the stationary nonlinear modes, we provide the full phase diagrams of its main transverse magnetic modes as a function of the total power, buffer layer, and core thicknesses that are more complex than the ones of the simple nonlinear metal slot. We show that these modes can exhibit spatial transitions toward specific modes of the new structure as a function of power. We also demonstrate that, for the main modes, the losses are reduced compared to the previous structures, and that they can now decrease with power. Finally, we describe the stability properties of the main stationary solutions using nonlinear FDTD simulations. PMID:27192282

  13. Characteristics of microstrip dipole antennas in a periodic structure with dielectric layers

    NASA Astrophysics Data System (ADS)

    Grinev, A. Iu.; Kotov, Iu. V.

    Microstrip dipole antennas in a periodic antenna array with dielectric layers are analyzed on the basis of a rigorous solution of an integral equation of the first kind with respect to the electric-field distribution on the dipole. Numerical results are presented on the partial radiation pattern of the antenna, the total input impedance, and the amplitude-phase distribution of the electric current on the dipole. The optimization of the antenna is considered.

  14. Numerical simulation of heat transfer and flow structure in 3-D turbulent boundary layer with imbedded longitudinal vortex

    SciTech Connect

    Jeong, J.Y.; Ryou, H.S.

    1997-03-01

    Heat transfer characteristics and flow structure in turbulent flows through a flat plate three-dimensional turbulent boundary layer containing built-in vortex generators have been analyzed by means of the space marching Crank-Nicolson finite difference method. The method solves the slender flow approximation of the steady three-dimensional Navier-Stokes and energy equations. This study used the eddy diffusivity model and standard {kappa}-{epsilon} model to predict heat transfer and flow field in the turbulent flow with imbedded longitudinal vortex. The results show boundary layer distortion due to vortices, such as strong spanwise flow divergence and boundary layer thinning. The heat transfer and skin friction show relatively good results in comparison with experimental data. The vortex core moves slightly away from the wall and grows slowly; consequently, the vortex influences the flow over a very long distance downstream. The enhancement of the heat transfer in the vicinity of the wall is due to the increasing spanwise separation of the vortices as they develop in the streamwise direction.

  15. Small is beautiful: the unusual transformation of nanocrystalline layered α-zirconium phosphate into a new 3D structure.

    PubMed

    Pica, Monica; Vivani, Riccardo; Donnadio, Anna; Troni, Elisabetta; Fop, Sacha; Casciola, Mario

    2015-09-21

    Nanosized α-zirconium phosphate, α-ZrP, undergoes a phase transition at 120 °C, which is not observed with microcrystalline α-ZrP in the same conditions, and which leads to a new 3D phase. The new compound, with formula Zr(HPO4)2 (τ'-ZrP), consists of cubelike nanoparticles and has a tetragonal unit cell (space group P43212, a = 7.955 Å, c = 10.744 Å). The structure of τ'-ZrP is in close relationship with that of the already known τ-ZrP. Both structures are made of packed chains of eight-membered rings, composed of Zr atoms connected to bridging HPO4 groups. The main difference between the two structures concerns the different orientation of the uncoordinated P-OH groups, pointing into the channels. The in situ XRPD analysis on nanosized α-ZrP, performed at 120 °C as a function of time, provided information about the kinetics of the formation of τ'-ZrP, showing that the α-ZrP phase is directly transformed into τ'-ZrP. Moreover, τ'-ZrP is converted into α-ZrP at room temperature in the presence of water vapor. It was proved that the free phosphoric acid, which is originally present in small amounts in nanosized α-ZrP and τ'-ZrP, is necessary for the interconversion between the two phases. As a matter of fact, the removal of phosphoric acid, by washing α-ZrP and τ'-ZrP with anhydrous ethanol, inhibits the above conversion. PMID:26322869

  16. 3D Modeling of influence of oxygenated inflows on biogeochemical structure of redox-layer of enclosed seas

    NASA Astrophysics Data System (ADS)

    Podymov, O.

    2009-04-01

    In this study we used a coupled hydrophysical-biogeochemical model. Biogeochemical processes were described with O-N-S-P-Mn-Fe ROLM model (Yakushev et al, 2007), designed to study processes of organic matter (OM) formation and decay, reduction and oxidation of species of nitrogen, sulphur, manganese and iron, transformation of phosphorus species. Phytoplankton, zooplankton and bacteria were also parameterized and divided into four groups according to their relation to particular energy source and to OM transformation. Hydrophysical processes where described with 3D General Estuarine Transport Model (Burchard et al, 2004). We modeled the influence of oxygenated intrusions on the vertical biogeochemical structure of the central Gotland Sea. The model simulations demonstrate that a complete ventilation of the Gotland Deep bottom water caused by massive inflows of oxygenated North Sea water led to substantial changes of the vertical biogeochemical structure within this basin. During the inflow events large amounts of iron and manganese precipitate and discharge from the water column. In this phase redox reactions are accelerated and growth of bacteria leads to an increase of particulate matter content and consecutive particle sedimentation. An unbalanced structure of water column exists during the period of reestablishment of anoxic conditions. Its appearance is related to the absence of Mn species that play the dominant role in the oxidation-reduction reactions at the pelagic redox interfaces. This unbalanced structure can serve as a biotope for a development of untypical microbial redox-cline reactions (i.e. anammox). According to the model simulations the duration of the reestablishment period for a steady state of biogeochemistry after a complete flushing is about 1.5 years.

  17. Dielectric constant estimation of the uppermost Basal Unit layer in the martian Boreales Scopuli region

    NASA Astrophysics Data System (ADS)

    Lauro, Sebastian E.; Mattei, Elisabetta; Soldovieri, Francesco; Pettinelli, Elena; Orosei, Roberto; Vannaroni, Giuliano

    2012-05-01

    An electromagnetic inversion model has been applied to echoes from the subsurface sounding Shallow Radar (SHARAD) to retrieve the dielectric properties of the uppermost Basal Unit (BU) beneath the North Polar Layered Deposits of Mars. SHARAD data have been carefully selected to satisfy the assumption of the inversion model which requires a stratigraphy consisting of mostly plane parallel layers. The resulting values of the dielectric constant have been interpreted in terms of a variable percentage of dust in an ice-dust mixture through the use of a mixing model for dielectric properties. The resulting dust content exceeds 65%, reaching perhaps 95%, depending on the permittivity values assumed for the dust. Such a concentration is higher than that obtained by Selvans et al. (Selvans, M.M., Plaut, J.J., Aharonson, O. [2010]. J. Geophys. Res, 115, E09003). This discrepancy could be justified considering that our observations refer to the uppermost BU layer, whereas Selvans et al. (Selvans, M.M., Plaut, J.J., Aharonson, O. [2010]. J. Geophys. Res, 115, E09003) probed the BU full thickness. Moreover, if the BU is considered spatially inhomogeneous, with very different dust content and thickness (Tanaka, K.L., Skinner, J.A., Fortezzo, C.M., Herkenhoff, K.E., Rodriguez, J.A.P., Bourke, M.C., Kolb, E.J., Okubo, C.H. [2008]. Icarus, 196, 318-358), the discrepancy could be furtherly reconciled.

  18. Dielectric Properties of Layered ZnTa2O6/Poly(tetrafluoroethylene) Composites

    NASA Astrophysics Data System (ADS)

    Jeon, Chang Jun; Kim, Eung Soo

    2012-11-01

    The effects of ZnTa2O6 content and layered structure on the dielectric properties of ZnTa2O6/poly(tetrafluoroethylene) (PTFE) composites were investigated at microwave frequency. With increasing ZnTa2O6 content, the dielectric constant (K) and dielectric loss (tan δ) of the composites increased due to the K values of the individual components and the microstructure. For the composites with layered structures, tan δ was dependent on the internal strain of the composites. Several types of theoretical models were employed to predict the effective K of the composites and the predicted values were compared with experimental data. The temperature coefficient of resonant frequency (TCF) was also discussed as it characterises the thermal stability of the composites. Typically, K of 4.24, tan δ of 1.36 ×10-3 and, TCF of 4.75 ppm/°C were obtained for the single layered PTFE composites with 0.2 volume fraction (Vf) of ZnTa2O6.

  19. Development and evaluation of a LOR-based image reconstruction with 3D system response modeling for a PET insert with dual-layer offset crystal design

    NASA Astrophysics Data System (ADS)

    Zhang, Xuezhu; Stortz, Greg; Sossi, Vesna; Thompson, Christopher J.; Retière, Fabrice; Kozlowski, Piotr; Thiessen, Jonathan D.; Goertzen, Andrew L.

    2013-12-01

    In this study we present a method of 3D system response calculation for analytical computer simulation and statistical image reconstruction for a magnetic resonance imaging (MRI) compatible positron emission tomography (PET) insert system that uses a dual-layer offset (DLO) crystal design. The general analytical system response functions (SRFs) for detector geometric and inter-crystal penetration of coincident crystal pairs are derived first. We implemented a 3D ray-tracing algorithm with 4π sampling for calculating the SRFs of coincident pairs of individual DLO crystals. The determination of which detector blocks are intersected by a gamma ray is made by calculating the intersection of the ray with virtual cylinders with radii just inside the inner surface and just outside the outer-edge of each crystal layer of the detector ring. For efficient ray-tracing computation, the detector block and ray to be traced are then rotated so that the crystals are aligned along the X-axis, facilitating calculation of ray/crystal boundary intersection points. This algorithm can be applied to any system geometry using either single-layer (SL) or multi-layer array design with or without offset crystals. For effective data organization, a direct lines of response (LOR)-based indexed histogram-mode method is also presented in this work. SRF calculation is performed on-the-fly in both forward and back projection procedures during each iteration of image reconstruction, with acceleration through use of eight-fold geometric symmetry and multi-threaded parallel computation. To validate the proposed methods, we performed a series of analytical and Monte Carlo computer simulations for different system geometry and detector designs. The full-width-at-half-maximum of the numerical SRFs in both radial and tangential directions are calculated and compared for various system designs. By inspecting the sinograms obtained for different detector geometries, it can be seen that the DLO crystal

  20. Coupling Between Microstrip Lines and Finite Ground Coplanar Lines Embedded in Polyimide Layers for 3D-MMICs on Silicon

    NASA Technical Reports Server (NTRS)

    Ponchak, G. E.; Bushyager, N.; Papapolymerou, J.; Tentzeris, E. M.; Laskar, J.

    2002-01-01

    Three-dimensional circuits built upon multiple layers of polyimide are required for constructing Si/SiGe monolithic microwave/mm-wave integrated circuits on CMOS (low resistivity) Si wafers. It is expected that these circuits will replace the ones fabricated on GaAs and reduce the overall system cost. However, the closely spaced transmission lines that are required for a high-density circuit environment are susceptible to high levels of cross-coupling, which degrades the overall circuit performance. In this paper, theoretical and experimental results on coupling and ways to reduce it are presented for two types of transmission lines: a) the microstrip line and b) the Finite Ground Coplanar (FGC) line. For microstrip lines it is shown that a fence of metalized via-holes can significantly reduce coupling, especially in the case when both lines are on the same polyimide layer or when the shielding structure extends through several polyimide layers. For closely spaced microstrip lines, coupling is lower for a metal filled trench shield than a via-hole fence. Coupling amongst microstrip lines is dependent on the ratio of line separation to polyimide thickness and is primarily due to magnetic fields. For FGC lines it is shown that they have in general low coupling that can be reduced significantly when there is even a small gap between the ground planes of each line. FGC lines have approximately 8 dB lower coupling than coupled coplanar waveguides (CPW). In addition, forward and backward characteristics of the FGC lines do not resemble those of other transmission lines such as microstrip. Therefore, the coupling mechanism of the FGC lines is different compared to thin film microstrip lines.

  1. Coupling Between Microstrip Lines with Finite Width Ground Plane Embedded in Polyimide Layers for 3D-MMICs on Si

    NASA Technical Reports Server (NTRS)

    Ponchak, George E.; Dalton, Edan; Tentzeris, Emmanouil M.; Papapolymerou, John; Williams, W. Dan (Technical Monitor)

    2001-01-01

    Three-dimensional circuits built upon multiple layers of polyimide are required for constructing Si/SiGe monolithic microwave/millimeter-wave integrated circuits on complementary metal oxide semiconductor (CMOS) (low resistivity) Si wafers. Thin film microstrip lines (TFMS) with finite width ground planes embedded in the polyimide are often used. However, the closely spaced TFMS lines are susceptible to high levels of coupling, which degrades circuit performance. In this paper, Finite Difference Time Domain (FDTD) analysis and experimental measurements are used to show that the ground planes must be connected by via holes to reduce coupling in both the forward and backward directions.

  2. Mechanochemical Synthesis of 3d Transition-Metal-1,2,4-Triazole Complexes as Precursors for Microwave-Assisted and Thermal Conversion to Coordination Polymers with a High Influence on the Dielectric Properties.

    PubMed

    Brede, Franziska A; Heine, Johanna; Sextl, Gerhard; Müller-Buschbaum, Klaus

    2016-02-01

    The complexes [MCl2 (TzH)4 ] (M=Mn (1), Fe (2); TzH=1,2,4-1H-triazole) and [ZnCl2 (TzH)2 ] (3) have been obtained by mechanochemical reactions of the corresponding divalent metal chloride and 1,2,4-1H-triazole. They were successfully used as precursors for the formation of coordination polymers either by a microwave-assisted reaction or by thermal conversion. For manganese, the conversion directly yielded 1∞ [MnCl2 TzH] (4), whereas for the iron-containing precursor, 1∞ [FeCl2 TzH] (6), was formed via the intermediate coordination polymer 1∞ [FeCl(TzH)2 ]Cl (5). For cobalt, the isotypic polymer 1∞ [CoCl(TzH)2 ]Cl (7) was obtained, but exclusively by a microwave-induced reaction directly from CoCl2 . The crystal structures were resolved from single crystals and powders. The dielectric properties were determined and revealed large differences in permittivity between the precursor complexes and the rigid chain-like coordination polymers. Whereas the monomeric complexes exhibit very different dielectric behaviour, depending on the transition metal, from "low-k" to "high-k" with the permittivity ranging from 4.3 to >100 for frequencies of up to 1000 Hz, the coordination polymers and complexes with strong intermolecular interactions are all close to "low-k" materials with very low dielectric constants up to 50 °C. Therefore, the conversion procedures can be used to deliberately influence the dielectric properties from complex to polymer and for different 3d transition-metal ions. PMID:26797710

  3. Effects of Complex Structured Anodic Oxide Dielectric Layer Grown in Pore Matrix for Aluminum Capacitor.

    PubMed

    Shin, Jin-Ha; Yun, Sook Young; Lee, Chang Hyoung; Park, Hwa-Sun; Suh, Su-Jeong

    2015-11-01

    Anodization of aluminum is generally divided up into two types of anodic aluminum oxide structures depending on electrolyte type. In this study, an anodization process was carried out in two steps to obtain high dielectric strength and break down voltage. In the first step, evaporated high purity Al on Si wafer was anodized in oxalic acidic aqueous solution at various times at a constant temperature of 5 degrees C. In the second step, citric acidic aqueous solution was used to obtain a thickly grown sub-barrier layer. During the second anodization process, the anodizing potential of various ranges was applied at room temperature. An increased thickness of the sub-barrier layer in the porous matrix was obtained according to the increment of the applied anodizing potential. The microstructures and the growth of the sub-barrier layer were then observed with an increasing anodizing potential of 40 to 300 V by using a scanning electron microscope (SEM). An impedance analyzer was used to observe the change of electrical properties, including the capacitance, dissipation factor, impedance, and equivalent series resistance (ESR) depending on the thickness increase of the sub-barrier layer. In addition, the breakdown voltage was measured. The results revealed that dielectric strength was improved with the increase of sub-barrier layer thickness. PMID:26726615

  4. Conductance of a single electron transistor with a retarded dielectric layer in the gate capacitor

    NASA Astrophysics Data System (ADS)

    Udalov, O. G.; Chtchelkatchev, N. M.; Fedorov, S. A.; Beloborodov, I. S.

    2015-11-01

    We study the conductance of a single electron transistor (SET) with a ferroelectric (or dielectric) layer placed in the gate capacitor. We assume that the ferroelectric (FE) has a retarded response with arbitrary relaxation time. We show that in the case of "fast" but still retarded response of the FE (dielectric) layer an additional contribution to the Coulomb blockade effect appears leading to the suppression of the SET conductance. We take into account fluctuations of the FE (dielectric) polarization using Monte Carlo simulations. For "fast" FE, these fluctuations partially suppress the additional Coulomb blockade effect. Using Monte Carlo simulations, we study the transition from "fast" to "slow" FE. For high temperatures, the peak value of the SET conductance is almost independent of the FE relaxation time. For temperatures close to the FE Curie temperature, the conductance peak value nonmonotonically depends on the FE relaxation time. A maximum appears when the FE relaxation time is of the order of the SET discharging time. Below the Curie point the conductance peak value decreases with increasing the FE relaxation time. The conductance shows the hysteresis behavior for any FE relaxation time at temperatures below the FE transition point. We show that conductance hysteresis is robust against FE internal fluctuations.

  5. Long-range wetting transparency on top of layered metal-dielectric substrates

    PubMed Central

    Noginov, M. A.; Barnakov, Yuri A.; Liberman, Vladimir; Prayakarao, Srujana; Bonner, Carl E.; Narimanov, Evgenii E.

    2016-01-01

    It has been recently shown that scores of physical and chemical phenomena (including spontaneous emission, scattering and Förster energy transfer) can be controlled by nonlocal dielectric environments provided by metamaterials with hyperbolic dispersion and simpler metal/dielectric structures. At this time, we have researched van der Waals interactions and experimentally studied wetting of several metallic, dielectric and composite multilayered substrates. We have found that the wetting angle of water on top of MgF2 is highly sensitive to the thickness of the MgF2 layer and the nature of the underlying substrate that could be positioned as far as ~100 nm beneath the water/MgF2 interface. We refer to this phenomenon as long range wetting transparency. The latter effect cannot be described in terms of the most basic model of dispersion van der Waals-London forces based on pair-wise summation of dipole-dipole interactions across an interface or a gap separating the two media. We infer that the experimentally observed gradual change of the wetting angle with increase of the thickness of the MgF2 layer can possibly be explained by the distance dependence of the Hamaker function (describing the strength of interaction), which originates from retardation of electromagnetic waves at the distances comparable to a wavelength. PMID:27324650

  6. Long-range wetting transparency on top of layered metal-dielectric substrates

    NASA Astrophysics Data System (ADS)

    Noginov, M. A.; Barnakov, Yuri A.; Liberman, Vladimir; Prayakarao, Srujana; Bonner, Carl E.; Narimanov, Evgenii E.

    2016-06-01

    It has been recently shown that scores of physical and chemical phenomena (including spontaneous emission, scattering and Förster energy transfer) can be controlled by nonlocal dielectric environments provided by metamaterials with hyperbolic dispersion and simpler metal/dielectric structures. At this time, we have researched van der Waals interactions and experimentally studied wetting of several metallic, dielectric and composite multilayered substrates. We have found that the wetting angle of water on top of MgF2 is highly sensitive to the thickness of the MgF2 layer and the nature of the underlying substrate that could be positioned as far as ~100 nm beneath the water/MgF2 interface. We refer to this phenomenon as long range wetting transparency. The latter effect cannot be described in terms of the most basic model of dispersion van der Waals-London forces based on pair-wise summation of dipole-dipole interactions across an interface or a gap separating the two media. We infer that the experimentally observed gradual change of the wetting angle with increase of the thickness of the MgF2 layer can possibly be explained by the distance dependence of the Hamaker function (describing the strength of interaction), which originates from retardation of electromagnetic waves at the distances comparable to a wavelength.

  7. Long-range wetting transparency on top of layered metal-dielectric substrates.

    PubMed

    Noginov, M A; Barnakov, Yuri A; Liberman, Vladimir; Prayakarao, Srujana; Bonner, Carl E; Narimanov, Evgenii E

    2016-01-01

    It has been recently shown that scores of physical and chemical phenomena (including spontaneous emission, scattering and Förster energy transfer) can be controlled by nonlocal dielectric environments provided by metamaterials with hyperbolic dispersion and simpler metal/dielectric structures. At this time, we have researched van der Waals interactions and experimentally studied wetting of several metallic, dielectric and composite multilayered substrates. We have found that the wetting angle of water on top of MgF2 is highly sensitive to the thickness of the MgF2 layer and the nature of the underlying substrate that could be positioned as far as ~100 nm beneath the water/MgF2 interface. We refer to this phenomenon as long range wetting transparency. The latter effect cannot be described in terms of the most basic model of dispersion van der Waals-London forces based on pair-wise summation of dipole-dipole interactions across an interface or a gap separating the two media. We infer that the experimentally observed gradual change of the wetting angle with increase of the thickness of the MgF2 layer can possibly be explained by the distance dependence of the Hamaker function (describing the strength of interaction), which originates from retardation of electromagnetic waves at the distances comparable to a wavelength. PMID:27324650

  8. Synthesis and characterization of hexagonal boron nitride film as a dielectric layer for graphene devices.

    PubMed

    Kim, Ki Kang; Hsu, Allen; Jia, Xiaoting; Kim, Soo Min; Shi, Yumeng; Dresselhaus, Mildred; Palacios, Tomas; Kong, Jing

    2012-10-23

    Hexagonal boron nitride (h-BN) is a promising material as a dielectric layer or substrate for two-dimensional electronic devices. In this work, we report the synthesis of large-area h-BN film using atmospheric pressure chemical vapor deposition on a copper foil, followed by Cu etching and transfer to a target substrate. The growth rate of h-BN film at a constant temperature is strongly affected by the concentration of borazine as a precursor and the ambient gas condition such as the ratio of hydrogen and nitrogen. h-BN films with different thicknesses can be achieved by controlling the growth time or tuning the growth conditions. Transmission electron microscope characterization reveals that these h-BN films are polycrystalline, and the c-axis of the crystallites points to different directions. The stoichiometry ratio of boron and nitrogen is close to 1:1, obtained by electron energy loss spectroscopy. The dielectric constant of h-BN film obtained by parallel capacitance measurements (25 μm(2) large areas) is 2-4. These CVD-grown h-BN films were integrated as a dielectric layer in top-gated CVD graphene devices, and the mobility of the CVD graphene device (in the few thousands cm(2)/(V·s) range) remains the same before and after device integration. PMID:22970651

  9. Scrape-off layer modeling of radiative divertor and high heat flux experiments on D3-D

    NASA Astrophysics Data System (ADS)

    Campbell, R. B.; Petrie, T. W.; Hill, D. N.

    1992-03-01

    We use a new multispecies 1-D fluid code, NEWT-1D, to model DIII-D scrape-off layer (SOL) behavior during radiative divertor and high heat flux experiments. The separatrix location and the width of the SOL are uncertain, and affect the comparison of the data in important ways. The model agrees with many of the experimental measurements for a particular prescription for the separatrix location. The model cannot explain the recent data on the separatrix T(sub i) with a conventional picture of ion and electron power flows across the separatrix. Radial transport of particles and heat in some form is required to explain the peak heat flux data before and after gas puffing. For argon puffing in the private flux region, entrainment is poor in the steady state. The calculations suggest that strike point argon puffing in a slot divertor geometry results in substantially better entrainment. Self-consistent, steady-state solutions with radiated powers up to 80 percent of the SOL power input are obtained in 1-D. We discuss significant radial effects which warrant the development of a code which can treat strongly radiating impurities in 2-D geometries.

  10. MRI-driven accretion on to magnetized stars: global 3D MHD simulations of magnetospheric and boundary layer regimes

    NASA Astrophysics Data System (ADS)

    Romanova, M. M.; Ustyugova, G. V.; Koldoba, A. V.; Lovelace, R. V. E.

    2012-03-01

    We discuss results of global three-dimensional magnetohydrodynamic simulations of accretion on to a rotating magnetized star with a tilted dipole magnetic field, where the accretion is driven by the magnetorotational instability (MRI). The simulations show that MRI-driven turbulence develops in the disc, and angular momentum is transported outwards primarily due to the magnetic stress. The turbulent flow is strongly inhomogeneous and the densest matter is in azimuthally stretched turbulent cells. We investigate two regimes of accretion: a magnetospheric regime and a boundary layer (BL) regime. In the magnetospheric regime, the magnetic field of the star is dynamically important: the accretion disc is truncated by the star's magnetic field within a few stellar radii from the star's surface, and matter flows to the star in funnel streams. The funnel streams flow towards the south and north magnetic poles but are not equal due to the inhomogeneity of the flow. The hotspots on the stellar surface are not symmetric as well. In the BL regime, the magnetic field of the star is dynamically unimportant, and matter accretes on to the surface of the star through the BL. The magnetic field in the inner disc is strongly amplified by the shear of the accretion flow, and the matter and magnetic stresses become comparable. Accreting matter forms a belt-shaped hot region on the surface of the star. The belt has inhomogeneous density distribution which varies in time due to variable accretion rate. The peaks in the variability curve are associated with accretion of individual turbulent cells. They show 20-50 per cent density amplifications at periods of ˜5-10 dynamical time-scales at the surface of the star. Spiral waves in the disc are excited in both magnetospheric and BL regimes of accretion. Results of simulations can be applied to classical T Tauri stars, accreting brown dwarfs, millisecond pulsars, dwarf novae cataclysmic variables and other stars with magnetospheres smaller

  11. Understanding the interfacial layer dynamics of polymer nanocomposites from broadband dielectric spectroscopy

    NASA Astrophysics Data System (ADS)

    Carroll, Robert; Cheng, Shiwang; Sokolov, Alexei

    Polymer nanocomposites show many advanced mechanical, thermal, optical, and transport properties mainly due to the vast interfacial area between the polymer matrix and nanoparticles. Recent studies show that there is an interfacial polymer layer with structure and dynamics that are different from the bulk polymer, and that contributes to the advanced macroscopic properties. It has been shown that broadband dielectric spectroscopy provides good method to study the interfacial dynamics in nanocomposites. However, current dielectric spectroscopy studies ignore the heterogeneous nature of polymer nanocomposites. Models based on a simple superposition of bulk polymer and interfacial layer spectra, or those that assume the interfacial layer is dynamically ``dead'' are inaccurate. In this talk, the prevailing methods in the literature will be compared with an accurate method accounting for the heterogeneity of the nanocomposites. Different nanocomposites with well-dispersed nanoparticles will be used as examples. The analysis clearly shows that the width and the amplitude of the relaxation peaks are affected by the data analysis. Thus accurate quantitative conclusions on properties and thickness of the interfacial layer can be achieved only using heterogeneous models.

  12. Layer-by-layer assembly of silica nanoparticles on 3D fibrous scaffolds: enhancement of osteoblast cell adhesion, proliferation, and differentiation.

    PubMed

    Tang, Yanwei; Zhao, Yan; Wang, Xungai; Lin, Tong

    2014-11-01

    Silica nanoparticles were applied onto the fiber surface of an interbonded three-dimensional polycaprolactone fibrous tissue scaffold by an electrostatic layer-by-layer self-assembly technique. The nanoparticle layer was found to improve the fiber wettability and surface roughness. Osteoblast cells were cultured on the fibrous scaffolds to evaluate the biological compatibility. The silica nanoparticle coated scaffold showed enhanced cell attachment, proliferation, and alkaline phosphatase activities. The overall results suggested that interbonded fibrous scaffold with silica nanoparticulate coating could be a promising scaffolding candidate for various applications in bone repair and regeneration. PMID:24288259

  13. Nickel–cobalt layered double hydroxide ultrathin nanoflakes decorated on graphene sheets with a 3D nanonetwork structure as supercapacitive materials

    SciTech Connect

    Yan, Tao; Li, Ruiyi; Li, Zaijun

    2014-03-01

    Graphical abstract: The microwave heating reflux approach was developed for the fabrication of nickel–cobalt layered double hydroxide ultrathin nanoflakes decorated on graphene sheets, in which ammonia and ethanol were used as the precipitator and medium for the synthesis. The obtained composite shows a 3D flowerclusters morphology with nanonetwork structure and largely enhanced supercapacitive performance. - Highlights: • The paper reported the microwave synthesis of nickel–cobalt layered double hydroxide/graphene composite. • The novel synthesis method is rapid, green, efficient and can be well used to the mass production. • The as-synthesized composite offers a 3D flowerclusters morphology with nanonetwork structure. • The composite offers excellent supercapacitive performance. • This study provides a promising route to design and synthesis of advanced graphene-based materials with the superiorities of time-saving and cost-effective characteristics. - Abstract: The study reported a novel microwave heating reflux method for the fabrication of nickel–cobalt layered double hydroxide ultrathin nanoflakes decorated on graphene sheets (GS/NiCo-LDH). Ammonia and ethanol were employed as precipitant and reaction medium for the synthesis, respectively. The resulting GS/NiCo-LDH offers a 3D flowerclusters morphology with nanonetwork structure. Due to the greatly enhanced rate of electron transfer and mass transport, the GS/NiCo-LDH electrode exhibits excellent supercapacitive performances. The maximum specific capacitance was found to be 1980.7 F g{sup −1} at the current density of 1 A g{sup −1}. The specific capacitance can remain 1274.7 F g{sup −1} at the current density of 15 A g{sup −1} and it has an increase of about 2.9% after 1500 cycles. Moreover, the study also provides a promising approach for the design and synthesis of metallic double hydroxides/graphene hybrid materials with time-saving and cost-effective characteristics, which can be

  14. Solid solution trends that impact electrical design of submicron layers in dielectric capacitors

    NASA Astrophysics Data System (ADS)

    Levi, Roni D.

    It is predictable that future thin layer multilayer dielectrics and thin films embedded capacitors will require higher field and higher reliability performance. This thesis explores the fundamental factors that would limit the high field and reliability performance in thin layer dielectrics based on BaTiO3. Those factors have different origins: On one side, the nature of the metal-dielectric interface was shown to affect the high field dielectric properties of capacitive structures. In addition to that, the intrinsic bulk properties of BaTiO3 based solid solutions affect the high field properties of thin dielectric layers depending on composition and annealing conditions. Both effects were investigated in this study. The temperature dependence of the electrical leakage current density of chemical solution deposited BaTiO3 films on high purity Ni foils was investigated as function of the underlying Ni microstructure. The electrical properties were then characterized on capacitors with and without the presence of Ni grain boundaries. When a Ni grain boundary from the substrate was present in the capacitor used during the electrical measurements, the loss tangent of the capacitor rose rapidly for dc biases exceeding ˜25kV/cm. The critical bias increases to ˜100kV/cm when no substrate grain boundaries are included in the capacitor. In addition, the capacitance-voltage curves are much more symmetric when grain boundaries are absent. This disparity in the electrical behavior was analyzed in terms of the mechanisms of charge conduction across the Ni-dielectric interface. While a reverse biased Schottky emission mechanism dominates the current in areas free of Ni grain boundaries, the Schottky barrier at the cathode is less effective when Ni grain boundaries are present due to local enhancement of the electric field. This, leads to a larger leakage current dominated by the forward biased Schottky barrier at the anode. In addition to the interface influence, the

  15. 3-D solar cells by electrochemical-deposited Se layer as extremely-thin absorber and hole conducting layer on nanocrystalline TiO2 electrode

    PubMed Central

    2013-01-01

    A three-dimensional selenium solar cell with the structure of Au/Se/porous TiO2/compact TiO2/fluorine-doped tin oxide-coated glass plates was fabricated by an electrochemical deposition method of selenium, which can work for the extremely thin light absorber and the hole-conducting layer. The effect of experimental conditions, such as HCl and H2SeO3 in an electrochemical solution and TiO2 particle size of porous layers, was optimized. This kind of solar cell did not use any buffer layer between an n-type electrode (porous TiO2) and a p-type absorber layer (selenium). The crystallinity of the selenium after annealing at 200°C for 3 min in the air was significantly improved. The cells with a selenium layer deposited at concentrations of HCl = 11.5 mM and H2SeO3 = 20 mM showed the best performance, resulting in 1- to 2-nm thickness of the Se layer, short-circuit photocurrent density of 8.7 mA/cm2, open-circuit voltage of 0.65 V, fill factor of 0.53, and conversion efficiency of 3.0%. PMID:23286700

  16. 3-D Quantum Transport Solver Based on the Perfectly Matched Layer and Spectral Element Methods for the Simulation of Semiconductor Nanodevices

    PubMed Central

    Cheng, Candong; Lee, Joon-Ho; Lim, Kim Hwa; Massoud, Hisham Z.; Liu, Qing Huo

    2007-01-01

    A 3-D quantum transport solver based on the spectral element method (SEM) and perfectly matched layer (PML) is introduced to solve the 3-D Schrödinger equation with a tensor effective mass. In this solver, the influence of the environment is replaced with the artificial PML open boundary extended beyond the contact regions of the device. These contact regions are treated as waveguides with known incident waves from waveguide mode solutions. As the transmitted wave function is treated as a total wave, there is no need to decompose it into waveguide modes, thus significantly simplifying the problem in comparison with conventional open boundary conditions. The spectral element method leads to an exponentially improving accuracy with the increase in the polynomial order and sampling points. The PML region can be designed such that less than −100 dB outgoing waves are reflected by this artificial material. The computational efficiency of the SEM solver is demonstrated by comparing the numerical and analytical results from waveguide and plane-wave examples, and its utility is illustrated by multiple-terminal devices and semiconductor nanotube devices. PMID:18037971

  17. Effect of dielectric spacer layers and substrate on SERS with Au nanoparticle arrays

    NASA Astrophysics Data System (ADS)

    Zhang, Xin; Briber, Robert M.; Rabin, Oded

    2015-03-01

    The optical response of a plasmonic nanostructure is often highly dependent on the nature of the underlying substrate. To study the effect of the substrate on surface enhanced Raman scattering (SERS), a series of SERS substrates were fabricated consisting of a hexagonal array of Au nanoparticles self assembled on block copolymer films, a silicon oxide (dielectric) layer and a silicon substrate or an Au substrate. The inter-particle distance and the dielectric layer thickness were controlled. The SERS Enhancement Factors (EF) were calculated by comparing the Raman spectra of 4-aminothiophenol adsorbed on the surface of the Au nanoparticles and in a standard solution. The SERS EF were found to be strongly affected by the inter-particle distance and silicon oxide thickness. Changing the inter-particle spacing induced a 102 variation in the EF, changing the oxide thickness increased EF values by an factor of 10, and changing substrate from Si to Au increased EF by a factor of 10. Maximal enhancement factors were found with oxide layer thicknesses between 30 nm and 50 nm beneath the 30 nm polymer film with Au substrates. This geometry both improved the resonance condition with the probe laser and reduced the absorption by the substrate. This work illustrates that optimization of plasmonic-based sensors should consider both the metallic and the surrounding structures. The Institute for Research in Electronics and Applied Physics (IREAP), University of Maryland, College Park, MD 20742.

  18. Epitaxial pentacene films grown on the surface of ion-beam-processed gate dielectric layer

    NASA Astrophysics Data System (ADS)

    Chou, W. Y.; Kuo, C. W.; Cheng, H. L.; Mai, Y. S.; Tang, F. C.; Lin, S. T.; Yeh, C. Y.; Horng, J. B.; Chia, C. T.; Liao, C. C.; Shu, D. Y.

    2006-06-01

    The following research describes the process of fabrication of pentacene films with submicron thickness, deposited by thermal evaporation in high vacuum. The films were fabricated with the aforementioned conditions and their characteristics were analyzed using x-ray diffraction, scanning electron microscopy, polarized Raman spectroscopy, and photoluminescence. Organic thin-film transistors (OTFTs) were fabricated on an indium tin oxide coated glass substrate, using an active layer of ordered pentacene molecules, which were grown at room temperature. Pentacene film was aligned using the ion-beam aligned method, which is typically employed to align liquid crystals. Electrical measurements taken on a thin-film transistor indicated an increase in the saturation current by a factor of 15. Pentacene-based OTFTs with argon ion-beam-processed gate dielectric layers of silicon dioxide, in which the direction of the ion beam was perpendicular to the current flow, exhibited a mobility that was up to an order of magnitude greater than that of the controlled device without ion-beam process; current on/off ratios of approximately 106 were obtained. Polarized Raman spectroscopy investigation indicated that the surface of the gate dielectric layer, treated with argon ion beam, enhanced the intermolecular coupling of pentacene molecules. The study also proposes the explanation for the mechanism of carrier transportation in pentacene films.

  19. Charge transport in thick SiO 2-based dielectric layers

    NASA Astrophysics Data System (ADS)

    Kanitz, Sven

    1997-12-01

    Charge transport in thick (≥ 1 μm) SiO 2-based dielectric layers was investigated by means of I( U) measurements. Investigations were carried out on thermally grown field oxide (FOX) as well as on TEOS and BPSG. Gate oxide layers (GOX) were measured as reference. C( U) measurements were performed for the determination of charges in the oxide. To determine the electrical parameters of the layers, the model from Chen and Wu[1] was developed further. The model takes into account tunnelling, capture and emission processes, impact ionization, recombination, interface states and ohmic currents. The I( U) characteristics for all dielectrics examined can be described with the aid of the model. The FOX parameters correspond to those of GOX. The parameters of TEOS and BPSG fluctuate strongly with the process parameters. After high-temperature annealing and from measurement of the examined parameters, the insulation properties of TEOS and BPSG were found to be at least as good as those of FOX.

  20. Organic carboxylate ligands tuned structural variations of two new Cd(II) coordination polymers: From 2D layer to 3D framework

    NASA Astrophysics Data System (ADS)

    Lv, Chang-Wei; Li, Jing; Liu, Yan-Wu; Li, Xia; Yuan, Zhi

    2015-11-01

    Two new Cd(II) coordination polymers, namely [Cd(4,4‧-sdb) (biimpy)]n·1.5n(H2O) (1) and [Cd2(Htci)2(biimpy)2]n (2) (4,4‧-H2sdb = 4,4‧-sulfonyldibenzoate, H3tci = tri(2-carboxyethyl)isocyanurate and biimpy = 2,6-bis(1-imdazoly)pyridine), have been synthesized by the hydrothermal reactions of Cd(NO3)2 and the mixed ligands of 4,4‧-H2sdb and biimpy or H3tci and biimpy. Single crystal X-ray structural analyses reveal that compound 1 features a 2D layered structure with 3-connected topology, and compound 2 features a 3D framework with 6-connected 6T8 topology. In addition, the thermal stabilities and luminescent properties of compounds 1 and 2 were also investigated.

  1. Validation of the RPLUS3D Code for Supersonic Inlet Applications Involving Three-Dimensional Shock Wave-Boundary Layer Interactions

    NASA Technical Reports Server (NTRS)

    Kapoor, Kamlesh; Anderson, Bernhard H.; Shaw, Robert J.

    1994-01-01

    A three-dimensional computational fluid dynamics code, RPLUS3D, which was developed for the reactive propulsive flows of ramjets and scramjets, was validated for glancing shock wave-boundary layer interactions. Both laminar and turbulent flows were studied. A supersonic flow over a wedge mounted on a flat plate was numerically simulated. For the laminar case, the static pressure distribution, velocity vectors, and particle traces on the flat plate were obtained. For turbulent flow, both the Baldwin-Lomax and Chien two-equation turbulent models were used. The static pressure distributions, pitot pressure, and yaw angle profiles were computed. In addition, the velocity vectors and particle traces on the flat plate were also obtained from the computed solution. Overall, the computed results for both laminar and turbulent cases compared very well with the experimentally obtained data.

  2. 2D THD and 3D TEHD analysis of large spindle supported thrust bearings with pins and double layer system used in the three gorges hydroelectric generators

    NASA Astrophysics Data System (ADS)

    Huang, B.; Wu, Z. D.; Wu, J. L.; Wang, L. Q.

    2012-11-01

    A 2D THD model and a 3DTEHD model for large spindle supported thrust bearings were set up and used to analyze the lubrication performance of the Three Gorges test thrust beating withpins and double layer system developed by Alstom Power. The finite difference method was employed to solve the THD model, and the thermal-elasticdeformations in the pad and runner were obtained by the finite element software ANSYS11.0. The data transfer between the THD model and ANSYS11.0 was carried out automatically by an interface program.A detailed comparison between the experimental results and numerical predictions by the two different modelsset up in this paper was carried out. Poor agreement has been found between the theoretical results obtained by 2D THD model and experimental data, while 3D TEHD provides fairly good agreement, confirming the importance of thermal effects and thermal-elastic deformations in both pad and runner.

  3. 3D-architectured nickel-cobalt-manganese layered double hydroxide/reduced graphene oxide composite for high-performance supercapacitor

    NASA Astrophysics Data System (ADS)

    Li, M.; Cheng, J. P.; Liu, F.; Zhang, X. B.

    2015-11-01

    Pure flower-like NiCoMn layered double hydroxide (LDH) and 3D-architectured NiCoMn LDH/reduced graphene oxide (rGO) composite are fabricated by a solution method. The NiCoMn hydroxide nanoflakes are tightly deposited on the surface of rGO. Electrochemical measurements prove that rGO can greatly improve its capacitive performances, compared with the pure counterpart. A high-specific capacitance of 912 F g-1, high-rate capability and long cycle life are achieved for the composite. A NiCoMn LDH/rGO//activated carbon hybrid capacitor is also fabricated. It possesses a high-specific capacitance of 206 F g-1 and an energy density of 92.8 W h kg-1 in 1.8 V.

  4. Enhanced Breakdown Reliability and Spatial Uniformity of Atomic Layer Deposited High-k Gate Dielectrics on Graphene via Organic Seeding Layers

    NASA Astrophysics Data System (ADS)

    Sangwan, Vinod; Jariwala, Deep; Filippone, Stephen; Karmel, Hunter; Johns, James; Alaboson, Justice; Marks, Tobin; Lauhon, Lincoln; Hersam, Mark

    2013-03-01

    Ultra-thin high- κ top-gate dielectrics are essential for high-speed graphene-based nanoelectronic circuits. Motivated by the need for high reliability and spatial uniformity, we report here the first statistical analysis of the breakdown characteristics of dielectrics grown on graphene. Based on these measurements, a rational approach is devised that simultaneously optimizes the gate capacitance and the key parameters of large-area uniformity and dielectric strength. In particular, vertically heterogeneous oxide stacks grown via atomic-layer deposition (ALD) seeded by a molecularly thin perylene-3,4,9,10-tetracarboxylic dianhydride (PTCDA) organic monolayer result in improved reliability (Weibull shape parameter β > 25) compared to the control dielectric directly grown on graphene without PTCDA (β < 1). The optimized sample also showed a large breakdown strength (Weibull scale parameter, EBD > 7 MV/cm) that is comparable to that of the control dielectric grown on Si substrates.

  5. CNT manipulation: inserting a carbonaceous dielectric layer beneath using electron beam induced deposition.

    PubMed

    Kurrat, Narendra; Vijaykumar, T; Kulkarni, G U

    2011-02-01

    Electron beam induced carbonaceous deposition has been carried out in the presence of water vapor at 0.4 torr pressure amidst residual hydrocarbons present in the SEM chamber. When performed at a CNT location on a Si substrate with low e beam energy (10 kV), the deposition was taking place beneath the CNT. While higher beam energy (25 kV) causing the deposition on the top surface of the CNT, in agreement with the earlier reports. The insertion of dielectric carbonaceous layer beneath the CNT allowed us to measure the I-V data along the length of the nanotube using CAFM. PMID:21456133

  6. Multi-layered dielectric cladding plasmonic microdisk resonator filter and coupler

    SciTech Connect

    Han Cheng, Bo; Lan, Yung-Chiang

    2013-02-15

    This work develops the plasmonic microdisk filter/coupler, whose effectiveness is evaluated by finite-difference time-domain simulation and theoretical analyses. Multi-layer dielectric cladding is used to prevent the scattering of surface plasmons (SPs) from a silver microdisk. This method allows devices that efficiently perform filter/coupler functions to be developed. The resonant conditions and the effective refractive index of bounded SP modes on the microdisk are determined herein. The waveguide-to-microdisk distance barely influences the resonant wavelength but it is inversely related to the bandwidth. These findings are consistent with predictions made using the typical ring resonator model.

  7. Differential capacitance of the electric double layer: the interplay between ion finite size and dielectric decrement.

    PubMed

    Nakayama, Yasuya; Andelman, David

    2015-01-28

    We study the electric double layer by combining the effects of ion finite size and dielectric decrement. At high surface potential, both mechanisms can cause saturation of the counter-ion concentration near a charged surface. The modified Grahame equation and differential capacitance are derived analytically for a general expression of a permittivity ε(n) that depends on the local ion concentration, n, and under the assumption that the co-ions are fully depleted from the surface. The concentration at counter-ion saturation is found for any ε(n), and a criterion predicting which of the two mechanisms (steric vs. dielectric decrement) is the dominant one is obtained. At low salinity, the differential capacitance as function of surface potential has two peaks (so-called camel-shape). Each of these two peaks is connected to a saturation of counter-ion concentration caused either by dielectric decrement or by their finite size. Because these effects depend mainly on the counter-ion concentration at the surface proximity, for opposite surface-potential polarity either the cations or anions play the role of counter-ions, resulting in an asymmetric camel-shape. At high salinity, we obtain and analyze the crossover in the differential capacitance from a double-peak shape to a uni-modal one. Finally, several nonlinear models of the permittivity decrement are considered, and we predict that the concentration at dielectrophoretic saturation shifts to higher concentration than those obtained by the linear decrement model. PMID:25638002

  8. Composite surface-plasmon-polariton waves guided by a thin metal layer sandwiched between a homogeneous isotropic dielectric material and a periodically multilayered isotropic dielectric material

    NASA Astrophysics Data System (ADS)

    Chiadini, Francesco; Fiumara, Vincenzo; Scaglione, Antonio; Lakhtakia, Akhlesh

    2015-01-01

    Multiple p- and s-polarized compound surface-plasmon-polariton (SPP) waves at a fixed frequency can be guided by a structure consisting of a metal layer sandwiched between a homogeneous isotropic dielectric (HID) material and a periodic multilayered isotropic dielectric (PMLID) material. For any thickness of the metal layer, at least one compound SPP wave must exist. It possesses the p-polarization state, and is strongly bound to the metal/HID interface when the metal thickness is large but to both metal/dielectric interfaces when the metal thickness is small. When the metal layer vanishes, this compound SPP wave transmutes into a Tamm wave. Additional compound SPP waves exist, depending on the thickness of the metal layer, the relative permittivity of the HID material, and the period and composition of the PMLID material. Some of these are p-polarized, the others are s-polarized. All of them differ in phase speed, attenuation rate, and field profile, even though all are excitable at the same frequency. The multiplicity and dependence of the number of compound SPP waves on the relative permittivity of the HID material when the metal layer is thin could be useful for optical sensing applications and intrachip plasmonic optical communication.

  9. Interface Engineering for Atomic Layer Deposited Alumina Gate Dielectric on SiGe Substrates.

    PubMed

    Zhang, Liangliang; Guo, Yuzheng; Hassan, Vinayak Vishwanath; Tang, Kechao; Foad, Majeed A; Woicik, Joseph C; Pianetta, Piero; Robertson, John; McIntyre, Paul C

    2016-07-27

    Optimization of the interface between high-k dielectrics and SiGe substrates is a challenging topic due to the complexity arising from the coexistence of Si and Ge interfacial oxides. Defective high-k/SiGe interfaces limit future applications of SiGe as a channel material for electronic devices. In this paper, we identify the surface layer structure of as-received SiGe and Al2O3/SiGe structures based on soft and hard X-ray photoelectron spectroscopy. As-received SiGe substrates have native SiOx/GeOx surface layers, where the GeOx-rich layer is beneath a SiOx-rich surface. Silicon oxide regrows on the SiGe surface during Al2O3 atomic layer deposition, and both SiOx and GeOx regrow during forming gas anneal in the presence of a Pt gate metal. The resulting mixed SiOx-GeOx interface layer causes large interface trap densities (Dit) due to distorted Ge-O bonds across the interface. In contrast, we observe that oxygen-scavenging Al top gates decompose the underlying SiOx/GeOx, in a selective fashion, leaving an ultrathin SiOx interfacial layer that exhibits dramatically reduced Dit. PMID:27345195

  10. Monochromatic filter with multiple manipulation approaches by the layered all-dielectric patch array.

    PubMed

    Liu, Xiaoshan; Liu, Guiqiang; Fu, Guolan; Liu, Mulin; Liu, Zhengqi

    2016-03-29

    Monochromatic filtering with ultra-narrowband and high spectral contrast is desirable for wide applications in display, image, and other optoelectronics. However, owing to the inherent omhic losses in the metallic materials, a broadband spectrum with a low Q-factor down to 10 inevitably limits the device performance. Herein, we for the first time theoretically propose and demonstrate an ultra-narrowband color-filtering platform based on the layered all-dielectric meta-material (LADM), which consists of a triple-layer high/low/high-index dielectrics cavity structure. Owing to the lossless dielectric materials used, sharp resonances with the bandwidth down to sub-10 nm are observed in the sub-wavelength LADM-based filters. A spectral Q-factor of 361.6 is achieved, which is orders of magnitude larger than that of the plasmonic resonators. Moreover, for the other significant factor for evaluation of filtering performance, the spectral contrast reaches 94.5%. These optical properties are the main results of the excitation of the resonant modes in the LADMs. Furthermore, polarization-manipulated light filtering is realized in this LADM. The classical Malus law is also confirmed in the reflective spectrum by tuning the polarization state. More interestingly and importantly, the filtering phenomenon shows novel features of the wavelength-independent and tunable resonant intensity for the reflective spectrum when the LADM-based filter is illuminated under an oblique state. High scalability of the sharp reflective spectrum is obtained by tuning the structural parameters. A single-wavelength reflective filtering window is also achieved in the visible frequencies. These features hold promise for the LADM-based filter with wide applications in color engineering, displaying, imaging, etc. PMID:26889575

  11. The jump-into-contact effect in biased AFM probes on dielectric films and its application to quantify the dielectric permittivity of thin layers

    NASA Astrophysics Data System (ADS)

    Revilla, Reynier I.

    2016-07-01

    The jump-into-contact (JIC) phenomenon in biased atomic force microscopy (AFM) probes on dielectric films is studied. The influence of the film thickness on the position at which the AFM tip collapses irreversibly into the sample surface was theoretically analyzed using a widely accepted analytical expression of the probe–sample electrostatic interaction force. It was demonstrated that for relatively high values of voltage (V > 10–20 V) applied between the probe and the substrate the cantilever deflection at the JIC is independent of the dielectric film thickness for thin–ultrathin layers (h < 10–50 nm). Under the same conditions the z–piezo distance at the JIC follows approximately a linear behavior with the film thickness. Based on this effect an empirical model was formulated to estimate the dielectric permittivity of thin/ultrathin dielectric films using the jump-into-contact distance. The procedure was successfully applied on thin PVD–SiO2 films, obtaining good agreement with a dielectric constant value previously reported for the same material.

  12. The jump-into-contact effect in biased AFM probes on dielectric films and its application to quantify the dielectric permittivity of thin layers.

    PubMed

    Revilla, Reynier I

    2016-07-01

    The jump-into-contact (JIC) phenomenon in biased atomic force microscopy (AFM) probes on dielectric films is studied. The influence of the film thickness on the position at which the AFM tip collapses irreversibly into the sample surface was theoretically analyzed using a widely accepted analytical expression of the probe-sample electrostatic interaction force. It was demonstrated that for relatively high values of voltage (V > 10-20 V) applied between the probe and the substrate the cantilever deflection at the JIC is independent of the dielectric film thickness for thin-ultrathin layers (h < 10-50 nm). Under the same conditions the z-piezo distance at the JIC follows approximately a linear behavior with the film thickness. Based on this effect an empirical model was formulated to estimate the dielectric permittivity of thin/ultrathin dielectric films using the jump-into-contact distance. The procedure was successfully applied on thin PVD-SiO2 films, obtaining good agreement with a dielectric constant value previously reported for the same material. PMID:27199351

  13. Application of a quasi-3D inviscid flow and boundary layer analysis to the hub-shroud contouring of a radial turbine

    NASA Technical Reports Server (NTRS)

    Civinskas, K. C.; Povinelli, L. A.

    1984-01-01

    Application of a quasi-3D approach to the aerodynamic analysis of several radial turbine configurations is described. The objective was to improve the rotor aerodynamic characteristics by hub-shroud contouring. The approach relies on available 2D inviscid methods coupled with boundary layer analysis to calculate profile, mixing, and endwall losses. Windage, tip clearance, incidence, and secondary flow losses are estimated from correlations. To eliminate separation along the hub and blade suction surfaces of a baseline rotor, the analysis was also applied to three alternate hub-shroud geometries. Emphasis was on elimination an inducer velocity overshoot as well as increasing hub velocities. While separation was never eliminated, the extent of the separated area was progressively reduced. Results are presented in terms of mid-channel and blade surface velocities; kinetic energy loss coefficients; and efficiency. The calculation demonstrates a first step for a systematic approach to radial turbine design that can be used to identify and control aerodynamic characteristics that ultimately determine heat transfer and component life. Experimentation will be required to assess the extent to which flow and boundary layer behavior were predicted correctly.

  14. Thermal and optical stability of injected charge in stacked dielectric layers

    NASA Astrophysics Data System (ADS)

    Wrana, M.; Schmidt, M.; Bräunig, D.

    1997-04-01

    Dielectric layer configurations of silicon dioxide/silicon nitride and silicon dioxide/silicon nitride/silicon dioxide were used to build up accumulation layers for back surface fields as well as inversion layers for inversion-layer solar cells. The silicon nitride was prepared by plasma-enhanced or low-pressure chemical vapour deposition. The high neutral trap concentration (0268-1242/12/4/004/img1) of the silicon nitride layer was utilized to increase the fixed charge, because these traps could be negatively charged by electron injection (photoinjection during an applied bias) or positively charged by photo-depopulation. The traps were charged/discharged by the irradiation of a deuterium lamp (4 eV to 6 eV) and the injected charge was measured by high-frequency capacitance - voltage measurements. We investigated the stability of injected charge with respect to temperature 0268-1242/12/4/004/img2 and optical degradation below air mass 1.5 condition (AM1.5). To explain the stability behaviour, we determined the band-offsets. Temperature stability could be confirmed for all examined configurations, but optical stability was seen only for the system 0268-1242/12/4/004/img3.

  15. Enhanced environmental stability induced by effective polarization of a polar dielectric layer in a trilayer dielectric system of organic field-effect transistors: a quantitative study.

    PubMed

    Subbarao, Nimmakayala V V; Gedda, Murali; Iyer, Parameswar K; Goswami, Dipak K

    2015-01-28

    We report a concept fabrication method that helps to improve the performance and stability of copper phthalocyanine (CuPc) based organic field-effect transistors (OFETs) in ambient. The devices were fabricated using a trilayer dielectric system that contains a bilayer polymer dielectrics consisting of a hydrophobic thin layer of poly(methyl methacrylate) (PMMA) on poly(vinyl alcohol) (PVA) or poly(4-vinylphenol) (PVP) or polystyrene (PS) with Al2O3 as a third layer. We have explored the peculiarities in the device performance (i.e., superior performance under ambient humidity), which are caused due to the polarization of dipoles residing in the polar dielectric material. The anomalous behavior of the bias-stress measured under vacuum has been explained successfully by a stretched exponential function modified by adding a time dependent dipole polarization term. The OFET with a dielectric layer of PVA or PVP containing hydroxyl groups has shown enhanced characteristics and remains highly stable without any degradation even after 300 days in ambient with three times enhancement in carrier mobility (0.015 cm(2)·V(-1)·s(-1)) compared to vacuum. This has been attributed to the enhanced polarization of hydroxyl groups in the presence of absorbed water molecules at the CuPc/PMMA interface. In addition, a model has been proposed based on the polarization of hydroxyl groups to explain the enhanced stability in these devices. We believe that this general method using a trilayer dielectric system can be extended to fabricate other OFETs with materials that are known to show high performances under vacuum but degrade under ambient conditions. PMID:25552195

  16. Dielectric properties of lead lanthanum zirconate titanate thin films with and without ZrO2 insertion layers

    NASA Astrophysics Data System (ADS)

    Liu, Shanshan; Ma, Beihai; Narayanan, Manoj; Tong, Sheng; Koritala, Rachel E.; Hu, Zhongqiang; Balachandran, Uthamalingam

    2013-05-01

    The dielectric properties of lead lanthanum zirconate titanate (PLZT) thin films on platinized silicon (Pt/Si) with and without ZrO2 insertion layers were investigated in the temperature range from 20 °C to 300 °C. Permittivity, dielectric loss tangent, and tunability were reduced for the samples with ZrO2 insertion layers compared to those without the layers. Additionally, the permittivity was less dependent on frequency over the broad temperature range studied (20-300 °C). The leakage current behavior of the PLZT films with and without ZrO2 insertion layers was also investigated, and on the basis of those results, a probable conduction mechanism has been suggested. The improved electrical properties in the PLZT with ZrO2 layers are attributed to the ZrO2 layer blocking the mobile ionic defects and reducing free charge carriers to transport.

  17. Rossby-wave driven stirring of the UTLS - a detailed view on the intricately layered structure by the 3-D imaging limb-sounder GLORIA

    NASA Astrophysics Data System (ADS)

    Ungermann, J.; Friedl-Vallon, F.; Hoepfner, M.; Oelhaf, H.; Preusse, P.; Riese, M.

    2014-12-01

    The Gimballed Limb Radiance Imager of the Atmosphere (GLORIA) is a new instrument that combines a classical Fourier transform spectrometer (FTS) with a 2-D detector array. Imaging allows the spatial sampling to be improved by up to an order of magnitude when compared to a limb scanning instrument. GLORIA is designed to operate on various high altitude research platforms. The instrument is a joint development of the German Helmholtz Large Research Facilities Karlsruhe Institute of Technology (KIT) and Research Centre Juelich (FZJ). GLORIA builds upon the heritage of KIT and FZJ in developing and operating IR limb sounders (MIPAS, CRISTA). In Summer 2012, GLORIA was an integral part of the first large missions for the German research aircraft HALO dedicated to atmospheric research, TACTS and ESMVAL. The data span latitudes from 80°N to 65°S and include several tomographic flight patterns that allow the 3-D reconstruction of observed air masses. We provide an overview of the heterogeneous structure of the upper troposphere/lower stratosphere (UTLS) as observed over Europe. Retrieved water vapor and ozone are used to identify the tropospheric or stratospheric character of air masses and can thus be used to visualize the multi-species 2-D (and partly 3-D) chemical structure of the UTLS. A highly intricate structure is found consisting often of fine-scale layers extending only several hundred meters in the vertical. These horizontally large-scale structures are thus below the typical vertical resolution of current chemistry climate models. Trajectory studies reveal the origin of the filaments to be Rossby wave-breaking events over the Pacific and Atlantic that cause tropical air stemming from the general area of the Asian monsoon to be mixed across the jet-stream into the subtropical lowermost stratosphere. These results demonstrate a rich spatial structure of the UTLS region at the subtropical jet, where the tropopause break is perturbed by breaking Rossby waves. The

  18. Water soluble poly(1-vinyl-1,2,4-triazole) as novel dielectric layer for organic field effect transistors

    PubMed Central

    Abbas, Mamatimin; Cakmak, Gulbeden; Tekin, Nalan; Kara, Ali; Guney, Hasan Yuksel; Arici, Elif; Sariciftci, Niyazi Serdar

    2011-01-01

    Water soluble poly(1-vinyl-1,2,4-triazole) (PVT) as a novel dielectric layer for organic field effect transistor is studied. Dielectric spectroscopy characterization reveals it has low leakage current and rather high breakdown voltage. Both n-channel and p-channel organic field effect transistors are fabricated using pentacene and fullerene as active layers. Both devices show device performances with lack of hysteresis, very low threshold voltages and high on/off ratios. Excellent film formation property is utilized to make AlOx and thin PVT bilayer in order to decrease the operating voltage of the devices. All solution processed ambipolar device is fabricated with simple spin coating steps using poly(2-methoxy-5-(2-ethyl-hexyloxy)-1,4-phenylenevinylene) (MEH–PPV) end capped with polyhedral oligomeric silsesquioxanes (POSS) as active layer. Our investigations show that PVT can be a very promising dielectric for organic field effect transistors. PMID:23794963

  19. From 1D-Multi-Layer-Conductivity-Inversion to Pseudo-3D-Imaging of Quantified Electromagnetic Induction Data Acquired at a Heterogeneous Test Site

    NASA Astrophysics Data System (ADS)

    von Hebel, Christian; Rudolph, Sebastian; Huisman, Johan A.; van der Kruk, Jan; Vereecken, Harry

    2013-04-01

    three different coil offsets in HCP and VCP measurement modes. This resulted in six high spatial resolution data sets of approximately 60000 measurements with different sensing depths. A 5 m block-kriging was applied to all six data sets to re-grid the sampling points on the same regular grid. For each grid node, the six measured apparent conductivities were used in a three-layer inversion. The three-layer inversion results of electrical conductivity thus obtained were used to derive a three-dimensional (3D) model of subsurface heterogeneity, which clearly indicated lateral and vertical conductivity changes of the subsurface that are related to changes in soil texture and soil water content.

  20. Wave attenuation and mode dispersion in a waveguide coated with lossy dielectric material

    NASA Technical Reports Server (NTRS)

    Lee, C. S.; Chuang, S. L.; Lee, S. W.; Lo, Y. T.

    1984-01-01

    The modal attenuation constants in a cylindrical waveguide coated with a lossy dielectric material are studied as functions of frequency, dielectric constant, and thickness of the dielectric layer. A dielectric material best suited for a large attenuation is suggested. Using Kirchhoff's approximation, the field attenuation in a coated waveguide which is illuminated by a normally incident plane wave is also studied. For a circular guide which has a diameter of two wavelengths and is coated with a thin lossy dielectric layer (omega sub r = 9.1 - j2.3, thickness = 3% of the radius), a 3 dB attenuation is achieved within 16 diameters.

  1. Arena3D: visualization of biological networks in 3D

    PubMed Central

    Pavlopoulos, Georgios A; O'Donoghue, Seán I; Satagopam, Venkata P; Soldatos, Theodoros G; Pafilis, Evangelos; Schneider, Reinhard

    2008-01-01

    Background Complexity is a key problem when visualizing biological networks; as the number of entities increases, most graphical views become incomprehensible. Our goal is to enable many thousands of entities to be visualized meaningfully and with high performance. Results We present a new visualization tool, Arena3D, which introduces a new concept of staggered layers in 3D space. Related data – such as proteins, chemicals, or pathways – can be grouped onto separate layers and arranged via layout algorithms, such as Fruchterman-Reingold, distance geometry, and a novel hierarchical layout. Data on a layer can be clustered via k-means, affinity propagation, Markov clustering, neighbor joining, tree clustering, or UPGMA ('unweighted pair-group method with arithmetic mean'). A simple input format defines the name and URL for each node, and defines connections or similarity scores between pairs of nodes. The use of Arena3D is illustrated with datasets related to Huntington's disease. Conclusion Arena3D is a user friendly visualization tool that is able to visualize biological or any other network in 3D space. It is free for academic use and runs on any platform. It can be downloaded or lunched directly from . Java3D library and Java 1.5 need to be pre-installed for the software to run. PMID:19040715

  2. Improved Gate Dielectric Deposition and Enhanced Electrical Stability for Single-Layer MoS2 MOSFET with an AlN Interfacial Layer

    PubMed Central

    Qian, Qingkai; Li, Baikui; Hua, Mengyuan; Zhang, Zhaofu; Lan, Feifei; Xu, Yongkuan; Yan, Ruyue; Chen, Kevin J.

    2016-01-01

    Transistors based on MoS2 and other TMDs have been widely studied. The dangling-bond free surface of MoS2 has made the deposition of high-quality high-k dielectrics on MoS2 a challenge. The resulted transistors often suffer from the threshold voltage instability induced by the high density traps near MoS2/dielectric interface or inside the gate dielectric, which is detrimental for the practical applications of MoS2 metal-oxide-semiconductor field-effect transistor (MOSFET). In this work, by using AlN deposited by plasma enhanced atomic layer deposition (PEALD) as an interfacial layer, top-gate dielectrics as thin as 6 nm for single-layer MoS2 transistors are demonstrated. The AlN interfacial layer not only promotes the conformal deposition of high-quality Al2O3 on the dangling-bond free MoS2, but also greatly enhances the electrical stability of the MoS2 transistors. Very small hysteresis (ΔVth) is observed even at large gate biases and high temperatures. The transistor also exhibits a low level of flicker noise, which clearly originates from the Hooge mobility fluctuation instead of the carrier number fluctuation. The observed superior electrical stability of MoS2 transistor is attributed to the low border trap density of the AlN interfacial layer, as well as the small gate leakage and high dielectric strength of AlN/Al2O3 dielectric stack. PMID:27279454

  3. Improved Gate Dielectric Deposition and Enhanced Electrical Stability for Single-Layer MoS2 MOSFET with an AlN Interfacial Layer.

    PubMed

    Qian, Qingkai; Li, Baikui; Hua, Mengyuan; Zhang, Zhaofu; Lan, Feifei; Xu, Yongkuan; Yan, Ruyue; Chen, Kevin J

    2016-01-01

    Transistors based on MoS2 and other TMDs have been widely studied. The dangling-bond free surface of MoS2 has made the deposition of high-quality high-k dielectrics on MoS2 a challenge. The resulted transistors often suffer from the threshold voltage instability induced by the high density traps near MoS2/dielectric interface or inside the gate dielectric, which is detrimental for the practical applications of MoS2 metal-oxide-semiconductor field-effect transistor (MOSFET). In this work, by using AlN deposited by plasma enhanced atomic layer deposition (PEALD) as an interfacial layer, top-gate dielectrics as thin as 6 nm for single-layer MoS2 transistors are demonstrated. The AlN interfacial layer not only promotes the conformal deposition of high-quality Al2O3 on the dangling-bond free MoS2, but also greatly enhances the electrical stability of the MoS2 transistors. Very small hysteresis (ΔVth) is observed even at large gate biases and high temperatures. The transistor also exhibits a low level of flicker noise, which clearly originates from the Hooge mobility fluctuation instead of the carrier number fluctuation. The observed superior electrical stability of MoS2 transistor is attributed to the low border trap density of the AlN interfacial layer, as well as the small gate leakage and high dielectric strength of AlN/Al2O3 dielectric stack. PMID:27279454

  4. Improved Gate Dielectric Deposition and Enhanced Electrical Stability for Single-Layer MoS2 MOSFET with an AlN Interfacial Layer

    NASA Astrophysics Data System (ADS)

    Qian, Qingkai; Li, Baikui; Hua, Mengyuan; Zhang, Zhaofu; Lan, Feifei; Xu, Yongkuan; Yan, Ruyue; Chen, Kevin J.

    2016-06-01

    Transistors based on MoS2 and other TMDs have been widely studied. The dangling-bond free surface of MoS2 has made the deposition of high-quality high-k dielectrics on MoS2 a challenge. The resulted transistors often suffer from the threshold voltage instability induced by the high density traps near MoS2/dielectric interface or inside the gate dielectric, which is detrimental for the practical applications of MoS2 metal-oxide-semiconductor field-effect transistor (MOSFET). In this work, by using AlN deposited by plasma enhanced atomic layer deposition (PEALD) as an interfacial layer, top-gate dielectrics as thin as 6 nm for single-layer MoS2 transistors are demonstrated. The AlN interfacial layer not only promotes the conformal deposition of high-quality Al2O3 on the dangling-bond free MoS2, but also greatly enhances the electrical stability of the MoS2 transistors. Very small hysteresis (ΔVth) is observed even at large gate biases and high temperatures. The transistor also exhibits a low level of flicker noise, which clearly originates from the Hooge mobility fluctuation instead of the carrier number fluctuation. The observed superior electrical stability of MoS2 transistor is attributed to the low border trap density of the AlN interfacial layer, as well as the small gate leakage and high dielectric strength of AlN/Al2O3 dielectric stack.

  5. Carbon materials with quasi-graphene layers: The dielectric, percolation properties and the electronic transport mechanism

    NASA Astrophysics Data System (ADS)

    Lu, Ming-Ming; Yuan, Jie; Wen, Bo; Liu, Jia; Cao, Wen-Qiang; Cao, Mao-Sheng

    2013-03-01

    We investigate the dielectric properties of multi-walled carbon nanotubes (MWCNTs) and graphite filling in SiO2 with the filling concentration of 2-20 wt.% in the frequency range of 102-107 Hz. MWCNTs and graphite have general electrical properties and percolation phenomena owing to their quasi-structure made up of graphene layers. Both permittivity ɛ and conductivity σ exhibit jumps around the percolation threshold. Variations of dielectric properties of the composites are in agreement with the percolation theory. All the percolation phenomena are determined by hopping and migrating electrons, which are attributed to the special electronic transport mechanism of the fillers in the composites. However, the twin-percolation phenomenon exists when the concentration of MWCNTs is between 5-10 wt.% and 15-20 wt.% in the MWCNTs/SiO2 composites, while in the graphite/SiO2 composites, there is only one percolation phenomenon in the graphite concentration of 10-15 wt.%. The unique twin-percolation phenomenon of MWCNTs/SiO2 is described and attributed to the electronic transfer mechanism, especially the network effect of MWCNTs in the composites. The network formation plays an essential role in determining the second percolation threshold of MWCNTs/SiO2.

  6. Effect of solution combusted TiO2 nanopowder within commercial BaTiO3 dielectric layer on the photoelectric properties for AC powder electroluminescence devices.

    PubMed

    Park, Sung; Choi, Gil Rak; Kim, Youn Cheol; Lee, Jae Chun; Lee, Ju Hyeon

    2013-05-01

    A unique synthesis method was developed, which is called solution combustion method (SCM). TiO2 nanopowder was synthesized by this method. This SCM TiO2 nanopowder (-35 nm) was added to the dielectric layer of AC powder electroluminescence (EL) device. The dielectric layer was made of commercial BaTiO3 powder (-1.2 microm) and binding polymer. 0, 5, 10 and 15 wt% of SCM TiO2 nanopowder was added to the dielectric layer during fabrication of AC powder EL device respectively. Dielectric constant of these four kinds of dielectric layers was measured. The brightness and current density of AC powder EL device were also measured. When 10 wt% of SCM TiO2 nanopowder was added, dielectric constant and brightness were increased by 30% and 101% respectively. Furthermore, the current density was decreased by 71%. This means that the brightness was double and the power consumption was one third. PMID:23858874

  7. High-performance hybrid supercapacitor with 3D hierarchical porous flower-like layered double hydroxide grown on nickel foam as binder-free electrode

    NASA Astrophysics Data System (ADS)

    Zhang, Luojiang; Hui, Kwun Nam; San Hui, Kwan; Lee, Haiwon

    2016-06-01

    The synthesis of layered double hydroxide (LDH) as electroactive material has been well reported; however, fabricating an LDH electrode with excellent electrochemical performance at high current density remains a challenge. In this paper, we report a 3D hierarchical porous flower-like NiAl-LDH grown on nickel foam (NF) through a liquid-phase deposition method as a high-performance binder-free electrode for energy storage. With large ion-accessible surface area as well as efficient electron and ion transport pathways, the prepared LDH-NF electrode achieves high specific capacity (1250 C g-1 at 2 A g-1 and 401 C g-1 at 50 A g-1) after 5000 cycles of activation at 20 A g-1 and high cycling stability (76.7% retention after another 5000 cycles at 50 A g-1), which is higher than those of most previously reported NiAl-LDH-based materials. Moreover, a hybrid supercapacitor with LDH-NF as the positive electrode and porous graphene nanosheet coated on NF (GNS-NF) as the negative electrode, delivers high energy density (30.2 Wh kg-1 at a power density of 800 W kg-1) and long cycle life, which outperforms the other devices reported in the literature. This study shows that the prepared LDH-NF electrode offers great potential in energy storage device applications.

  8. Shift and elimination of microwave Fabry-Perot resonances in a dielectric covered with a thin metal layer

    NASA Astrophysics Data System (ADS)

    Ragulis, Paulius; Simniškis, Rimantas; Kancleris, Žilvinas

    2015-04-01

    In this paper, we consider a plane electromagnetic wave incident onto a dielectric plate, which has one surface covered with a thin layer of metal. An oblique incident angle was considered for the TE (s polarization in optic) and TM (p polarization) plane waves. The thin metal layer is treated as an infinitesimal thickness. It was characterized by a surface conductivity and accounted for by a tangential magnetic field component step induced by the current flow in the metal layer. Compact expressions, which describe the reflection, transmission and absorption in a dielectric plate covered with a thin layer of metal, have been obtained. It was shown that by choosing the appropriate surface conductivity, the Fabry-Perot transmission resonances can be shifted to the position where the maximum reflection is observed in the case of an uncovered dielectric. On the other hand, the elimination of the Fabry-Perot resonances can be also achieved by choosing a proper metal surface conductivity. Measurements of the reflection from the glass covered with a thin layer of metal have been performed in a wide microwave frequency range (2-12 GHz) revealing a large difference in the measured reflection coefficient from the dielectric and metalized surfaces. The measured results fit well with those calculated by employing analytical expressions obtained in this paper.

  9. Bioprinting of 3D hydrogels.

    PubMed

    Stanton, M M; Samitier, J; Sánchez, S

    2015-08-01

    Three-dimensional (3D) bioprinting has recently emerged as an extension of 3D material printing, by using biocompatible or cellular components to build structures in an additive, layer-by-layer methodology for encapsulation and culture of cells. These 3D systems allow for cell culture in a suspension for formation of highly organized tissue or controlled spatial orientation of cell environments. The in vitro 3D cellular environments simulate the complexity of an in vivo environment and natural extracellular matrices (ECM). This paper will focus on bioprinting utilizing hydrogels as 3D scaffolds. Hydrogels are advantageous for cell culture as they are highly permeable to cell culture media, nutrients, and waste products generated during metabolic cell processes. They have the ability to be fabricated in customized shapes with various material properties with dimensions at the micron scale. 3D hydrogels are a reliable method for biocompatible 3D printing and have applications in tissue engineering, drug screening, and organ on a chip models. PMID:26066320

  10. Dielectric Barrier Discharge Ionization in Characterization of Organic Compounds Separated on Thin-Layer Chromatography Plates

    PubMed Central

    Cegłowski, Michał; Smoluch, Marek; Babij, Michał; Gotszalk, Teodor; Silberring, Jerzy; Schroeder, Grzegorz

    2014-01-01

    A new method for on-spot detection and characterization of organic compounds resolved on thin layer chromatography (TLC) plates has been proposed. This method combines TLC with dielectric barrier discharge ionization (DBDI), which produces stable low-temperature plasma. At first, the compounds were separated on TLC plates and then their mass spectra were directly obtained with no additional sample preparation. To obtain good quality spectra the center of a particular TLC spot was heated from the bottom to increase volatility of the compound. MS/MS analyses were also performed to additionally characterize all analytes. The detection limit of proposed method was estimated to be 100 ng/spot of compound. PMID:25170762

  11. Transparent actuator made with few layer graphene electrode and dielectric elastomer, for variable focus lens

    NASA Astrophysics Data System (ADS)

    Hwang, Taeseon; Kwon, Hyeok-Yong; Oh, Joon-Suk; Hong, Jung-Pyo; Hong, Seung-Chul; Lee, Youngkwan; Ryeol Choi, Hyouk; Jin Kim, Kwang; Hossain Bhuiya, Mainul; Nam, Jae-Do

    2013-07-01

    A transparent dielectric elastomer actuator driven by few-layer-graphene (FLG) electrode was experimentally investigated. The electrodes were made of graphene, which was dispersed in N-methyl-pyrrolidone. The transparent actuator was fabricated from developed FLG electrodes. The FLG electrode with its sheet resistance of 0.45 kΩ/sq (80 nm thick) was implemented to mask silicone elastomer. The developed FLG-driven actuator exhibited an optical transparency of over 57% at a wavenumber of 600 nm and produced bending displacement performance ranging from 29 to 946 μm as functions of frequency and voltage. The focus variation was clearly demonstrated under actuation to study its application-feasibility in variable focus lens and various opto-electro-mechanical devices.

  12. Vacuum ultraviolet photochemical selective area atomic layer deposition of Al2O3 dielectrics

    NASA Astrophysics Data System (ADS)

    Chalker, P. R.; Marshall, P. A.; Dawson, K.; Brunell, I. F.; Sutcliffe, C. J.; Potter, R. J.

    2015-01-01

    We report the photochemical atomic layer deposition of Al2O3 thin films and the use of this process to achieve area-selective film deposition. A shuttered vacuum ultraviolet (VUV) light source is used to excite molecular oxygen and trimethyl aluminum to deposit films at 60°C. In-situ QCM and post-deposition ellipsometric measurements both show that the deposition rate is saturative as a function of irradiation time. Selective area deposition was achieved by projecting the VUV light through a metalized magnesium fluoride photolithographic mask and the selectivity of deposition on the illuminated and masked regions of the substrate is a logarithmic function of the UV exposure time. The Al2O3 films exhibit dielectric constants of 8 - 10 at 1 MHz after forming gas annealing, similar to films deposited by conventional thermal ALD.

  13. OPTIMIZING A PORTABLE MICROWAVE INTERFERENCE SCANNING SYSTEM FOR NONDESTRUCTIVE TESTING OF MULTI-LAYERED DIELECTRIC MATERIALS

    SciTech Connect

    Schmidt, K. F. Jr.; Little, J. R. Jr.; Ellingson, W. A.; Green, W.

    2010-02-22

    The projected microwave energy pattern, wave guide geometry, positioning methods and process variables have been optimized for use of a portable, non-contact, lap-top computer-controlled microwave interference scanning system on multi-layered dielectric materials. The system can be used in situ with one-sided access and has demonstrated capability of damage detection on composite ceramic armor. Specimens used for validation included specially fabricated surrogates, and ballistic impact-damaged specimens. Microwave data results were corroborated with high resolution direct-digital x-ray imaging. Microwave interference scanning detects cracks, laminar features and material properties variations. This paper presents the details of the system, the optimization steps and discusses results obtained.

  14. High-current Electron Beam Coupling to Hybrid Waveguide and Plasma Modes in a Dielectric Cherenkov Maser with a Plasma Layer

    NASA Astrophysics Data System (ADS)

    Shlapakovski, Anatoli S.

    2002-12-01

    The linear theory of a dielectric Cherenkov maser with a plasma layer has been developed. The dispersion relation has been derived for the model of infinitely thin, fully magnetized, monoenergetic hollow electron beam, in the axisymmetric case. The results of the numerical solution of the dispersion relation and the analysis of the beam coupling to hybrid waves, both hybrid waveguide and hybrid plasma modes, are presented. For the hybrid waveguide mode, spatial growth rate dependences on frequency at different plasma densities demonstrate improvement in gain for moderate densities, but strong shifting the amplification band and narrowing the bandwidth. For the hybrid plasma mode, the case of mildly relativistic, 200-250 keV beams is of interest, so that the wave phase velocity is just slightly greater than the speed of light in a dielectric medium. It has been shown that depending on beam and plasma parameters, the hybrid plasma mode can be separated from the hybrid waveguide mode, or be coupled to it through the beam resulting in strong gain increase, or exhibit a flat gain vs frequency dependence over a very broad band. The parameters, at which the -3 dB bandwidth calculated for 30 dB peak gain exceeds an octave, have been found.

  15. Approximate analytical solution for waveguide excitation of a plane dielectric layer by a Gaussian beam at frustrated total internal reflection.

    PubMed

    Serdyuk, Vladimir; Rudnitsky, Anton

    2015-05-01

    We present an approximate 2D asymptotic analytic theory of light field excitation in a plane thin dielectric layer under conditions of frustrated total internal reflection, when an inclined Gaussian beam, falling from a triangular prism, excites a decaying field in air spacing between a prism and a plane dielectric. Ignoring the radiation scattering on the sharp edges of a prism, we have obtained the formulas that allow us to compute spatial structures of an electromagnetic field in every point of space and to estimate the integral efficiency of waveguide mode excitation in a plane dielectric layer and the total energy of a reflected beam. It is shown that the width of an initial Gaussian beam has an effect on waveguide mode intensity. PMID:26366908

  16. Heat resistive dielectric multi-layer micro-mirror array in epitaxial lateral overgrowth gallium nitride.

    PubMed

    Huang, Chen-Yang; Ku, Hao-Min; Liao, Wei-Tsai; Chao, Chu-Li; Tsay, Jenq-Dar; Chao, Shiuh

    2009-03-30

    Ta2O5 / SiO2 dielectric multi-layer micro-mirror array (MMA) with 3mm mirror size and 6mm array period was fabricated on c-plane sapphire substrate. The MMA was subjected to 1200 degrees C high temperature annealing and remained intact with high reflectance in contrast to the continuous multi-layer for which the layers have undergone severe damage by 1200 degrees C annealing. Epitaxial lateral overgrowth (ELO) of gallium nitride (GaN) was applied to the MMA that was deposited on both sapphire and sapphire with 2:56 mm GaN template. The MMA was fully embedded in the ELO GaN and remained intact. The result implies that our MMA is compatible to the high temperature growth environment of GaN and the MMA could be incorporated into the structure of the micro-LED array as a one to one micro backlight reflector, or as the patterned structure on the large area LED for controlling the output light. PMID:19333330

  17. Atomic-layer-deposited silver and dielectric nanostructures for plasmonic enhancement of Raman scattering from nanoscale ultrathin films.

    PubMed

    Ko, Chung-Ting; Yang, Po-Shuan; Han, Yin-Yi; Wang, Wei-Cheng; Huang, Jhih-Jie; Lee, Yen-Hui; Tsai, Yi-Jen; Shieh, Jay; Chen, Miin-Jang

    2015-07-01

    Plasmonic silver nanostructures and a precise ZnO cover layer prepared by capacitively coupled plasma atomic layer deposition (ALD) were exploited to enhance the Raman scattering from nanoscale ultrathin films on a Si substrate. The plasmonic activity was supported by a nanostructured Ag (nano-Ag) layer, and a ZnO cover layer was introduced upon the nano-Ag layer to spectrally tailor the localized surface plasmon resonance to coincide with the laser excitation wavelength. Because of the optimized dielectric environment provided by the precise growth of ZnO cover layer using ALD, the intensity of Raman scattering from nanoscale ultrathin films was significantly enhanced by an additional order of magnitude, leading to the observation of the monoclinic and tetragonal phases in the nanoscale ZrO2 high-K gate dielectric as thin as ∼6 nm on Si substrate. The excellent agreement between the finite-difference time-domain simulation and experimental measurement further confirms the so-called [absolute value]E(->)[absolute value](4) dependence of the surface-enhanced Raman scattering. This technique of plasmonic enhancement of Raman spectroscopy, assisted by the nano-Ag layer and optimized dielectric environment prepared by ALD, can be applied to characterize the structures of ultrathin films in a variety of nanoscale materials and devices, even on a Si substrate with overwhelming Raman background. PMID:26057412

  18. Effects of annealing conditions on the dielectric properties of solution-processed Al2O3 layers for indium-zinc-tin-oxide thin-film transistors.

    PubMed

    Kim, Yong-Hoon; Kim, Kwang-Ho; Park, Sung Kyu

    2013-11-01

    In this paper, the effects of annealing conditions on the dielectric properties of solution-processed aluminum oxide (Al2O3) layers for indium-zinc-tin-oxide (IZTO) thin-film transistors (TFTs) have been investigated. The dielectric properties of Al2O3 layers such as leakage current density and dielectric strength were largely affected by their annealing conditions. In particular, oxygen partial pressure in rapid thermal annealing, and the temperature profile of hot plate annealing had profound effects on the dielectric properties. From a refractive index analysis, the enhanced dielectric properties of Al2O3 gate dielectrics can be attributed to higher film density depending on the annealing conditions. With the low-temperature-annealed Al2O3 gate dielectric at 350 degrees C, solution-processed IZTO TFTs with a field-effect mobility of approximately 2.2 cm2/Vs were successfully fabricated. PMID:24245333

  19. High carrier mobility of CoPc wires based field-effect transistors using bi-layer gate dielectric

    SciTech Connect

    Gedda, Murali; Obaidulla, Sk. Md.; Subbarao, Nimmakayala V. V.; Goswami, Dipak K.

    2013-11-15

    Polyvinyl alcohol (PVA) and anodized Al{sub 2}O{sub 3} layers were used as bi-layer gate for the fabrication of cobalt phthalocyanine (CoPc) wire base field-effect transistors (OFETs). CoPc wires were grown on SiO{sub 2} surfaces by organic vapor phase deposition method. These devices exhibit a field-effect carrier mobility (μ{sub EF}) value of 1.11 cm{sup 2}/Vs. The high carrier mobility for CoPc molecules is attributed to the better capacitive coupling between the channel of CoPc wires and the gate through organic-inorganic dielectric layer. Our measurements also demonstrated the way to determine the thicknesses of the dielectric layers for a better process condition of OFETs.

  20. Parametric Dielectric Map of the Martian North Polar Layered Deposits in Support of the MARSIS and SHARAD data analysis

    NASA Astrophysics Data System (ADS)

    Cosmidis, J.; Heggy, E.; Clifford, S. M.

    2007-12-01

    Laboratory dielectric characterizations of Ice-dust mixtures are crucial for the quantitative analysis of radar sounding data as for the case of the MARSIS and SHARAD experiments. Understanding the range of the dielectric properties of the Martian northmen Polar layer deposits as well as their geographical an vertical distribution result in a better topographical mapping of the basement material below the northern polar cap and help constrain the ambiguities on the identification of layering and any potential subglaciar melting. In order to achieve this task, we constructed first order modeled maps of the surface dielectric properties oh the NPLD. We first used the recent Mars Global Surveyor Thermal Emission Spectrometer (TES) thermal inertia observations in order to derive a map of the dust mass fraction in the ice at the top of the permanent cap. Then we used parametric laboratory measurements of the dielectric properties of Martian polar ice analogs with various temperatures, radar frequencies and mass fractions and compositions of dust in order to obtain the parametric dielectric maps. Thermal inertia maps have been derived from recent TES observations of the surface temperatures of Mars taken over three Mars-years from orbit 1583 to 24346. Laboratory dielectric characterization of ice-dust mixtures has been performed using TES dust calibration samples provided by the ARES group at NASA JSC. Our Maps suggest that surface dielectric properties of the northern Polar cap ranges from 2.72 to 3.23 in the 2-20 MHz band for a dust inclusion typical of Martian basalt. Parametric maps of loss tangent, penetration depth for several dust types will be presented at the conference.

  1. Electrochemical and bio-sensing platform based on a novel 3D Cu nano-flowers/layered MoS₂ composite.

    PubMed

    Lin, Xiaoyun; Ni, Yongnian; Kokot, Serge

    2016-05-15

    A novel 3D nano-flower-like Cu/multi-layer molybdenum disulfide composite (CuNFs/MoS2) modified glassy carbon electrode (GCE) has been successfully constructed. It was a highly sensitive and selective non-enzymatic hydrogen peroxide (H2O2) and glucose biosensor. The morphology of the obtained CuNFs-MoS2 nano-particles was investigated with the use of a scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDS). The physicochemical properties of the modified electrode were characterized at each of the construction stages with the use of an electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) techniques. The new sensor combined the advantages of MoS2 and CuNFs, and exhibited high electro-catalytic activity toward H2O2 and glucose. Quantitative analysis of H2O2 and glucose was carried out with the use of the amperometric i-t method. Linear ranges were obtained between 0.04-1.88 μM and 1.88-35.6 μM for H2O2 and 1-20 μM and 20-70 μM for glucose, and their corresponding limits of detection (LOD) were 0.021 μM and 0.32 μM. This novel sensor was successfully applied for the quantitative analysis of H2O2 in tap water and glucose in human serum samples. PMID:26773372

  2. 3D Printing and Its Urologic Applications

    PubMed Central

    Soliman, Youssef; Feibus, Allison H; Baum, Neil

    2015-01-01

    3D printing is the development of 3D objects via an additive process in which successive layers of material are applied under computer control. This article discusses 3D printing, with an emphasis on its historical context and its potential use in the field of urology. PMID:26028997

  3. 3D Printing and Its Urologic Applications.

    PubMed

    Soliman, Youssef; Feibus, Allison H; Baum, Neil

    2015-01-01

    3D printing is the development of 3D objects via an additive process in which successive layers of material are applied under computer control. This article discusses 3D printing, with an emphasis on its historical context and its potential use in the field of urology. PMID:26028997

  4. Seeding atomic layer deposition of high-k dielectrics on epitaxial graphene with organic self-assembled monolayers.

    PubMed

    Alaboson, Justice M P; Wang, Qing Hua; Emery, Jonathan D; Lipson, Albert L; Bedzyk, Michael J; Elam, Jeffrey W; Pellin, Michael J; Hersam, Mark C

    2011-06-28

    The development of high-performance graphene-based nanoelectronics requires the integration of ultrathin and pinhole-free high-k dielectric films with graphene at the wafer scale. Here, we demonstrate that self-assembled monolayers of perylene-3,4,9,10-tetracarboxylic dianhydride (PTCDA) act as effective organic seeding layers for atomic layer deposition (ALD) of HfO(2) and Al(2)O(3) on epitaxial graphene on SiC(0001). The PTCDA is deposited via sublimation in ultrahigh vacuum and shown to be highly ordered with low defect density by molecular-resolution scanning tunneling microscopy. Whereas identical ALD conditions lead to incomplete and rough dielectric deposition on bare graphene, the chemical functionality provided by the PTCDA seeding layer yields highly uniform and conformal films. The morphology and chemistry of the dielectric films are characterized by atomic force microscopy, ellipsometry, cross-sectional scanning electron microscopy, and X-ray photoelectron spectroscopy, while high-resolution X-ray reflectivity measurements indicate that the underlying graphene remains intact following ALD. Using the PTCDA seeding layer, metal-oxide-graphene capacitors fabricated with a 3 nm Al(2)O(3) and 10 nm HfO(2) dielectric stack show high capacitance values of ∼700 nF/cm(2) and low leakage currents of ∼5 × 10(-9) A/cm(2) at 1 V applied bias. These results demonstrate the viability of sublimated organic self-assembled monolayers as seeding layers for high-k dielectric films in graphene-based nanoelectronics. PMID:21553842

  5. Europeana and 3D

    NASA Astrophysics Data System (ADS)

    Pletinckx, D.

    2011-09-01

    The current 3D hype creates a lot of interest in 3D. People go to 3D movies, but are we ready to use 3D in our homes, in our offices, in our communication? Are we ready to deliver real 3D to a general public and use interactive 3D in a meaningful way to enjoy, learn, communicate? The CARARE project is realising this for the moment in the domain of monuments and archaeology, so that real 3D of archaeological sites and European monuments will be available to the general public by 2012. There are several aspects to this endeavour. First of all is the technical aspect of flawlessly delivering 3D content over all platforms and operating systems, without installing software. We have currently a working solution in PDF, but HTML5 will probably be the future. Secondly, there is still little knowledge on how to create 3D learning objects, 3D tourist information or 3D scholarly communication. We are still in a prototype phase when it comes to integrate 3D objects in physical or virtual museums. Nevertheless, Europeana has a tremendous potential as a multi-facetted virtual museum. Finally, 3D has a large potential to act as a hub of information, linking to related 2D imagery, texts, video, sound. We describe how to create such rich, explorable 3D objects that can be used intuitively by the generic Europeana user and what metadata is needed to support the semantic linking.

  6. Atomic Layer Deposited Thin Films for Dielectrics, Semiconductor Passivation, and Solid Oxide Fuel Cells

    NASA Astrophysics Data System (ADS)

    Xu, Runshen

    Atomic layer deposition (ALD) utilizes sequential precursor gas pulses to deposit one monolayer or sub-monolayer of material per cycle based on its self-limiting surface reaction, which offers advantages, such as precise thickness control, thickness uniformity, and conformality. ALD is a powerful means of fabricating nanoscale features in future nanoelectronics, such as contemporary sub-45 nm metal-oxide-semiconductor field effect transistors, photovoltaic cells, near- and far-infrared detectors, and intermediate temperature solid oxide fuel cells. High dielectric constant, kappa, materials have been recognized to be promising candidates to replace traditional SiO2 and SiON, because they enable good scalability of sub-45 nm MOSFET (metal-oxide-semiconductor field-effect transistor) without inducing additional power consumption and heat dissipation. In addition to high dielectric constant, high-kappa materials must meet a number of other requirements, such as low leakage current, high mobility, good thermal and structure stability with Si to withstand high-temperature source-drain activation annealing. In this thesis, atomic layer deposited Er2O3 doped TiO2 is studied and proposed as a thermally stable amorphous high-kappa dielectric on Si substrate. The stabilization of TiO2 in its amorphous state is found to achieve a high permittivity of 36, a hysteresis voltage of less than 10 mV, and a low leakage current density of 10-8 A/cm-2 at -1 MV/cm. In III-V semiconductors, issues including unsatisfied dangling bonds and native oxides often result in inferior surface quality that yields non-negligible leakage currents and degrades the long-term performance of devices. The traditional means for passivating the surface of III-V semiconductors are based on the use of sulfide solutions; however, that only offers good protection against oxidation for a short-term (i.e., one day). In this work, in order to improve the chemical passivation efficacy of III-V semiconductors

  7. Flexible FETs using ultrathin Si microwires embedded in solution processed dielectric and metal layers

    NASA Astrophysics Data System (ADS)

    Khan, S.; Yogeswaran, N.; Taube, W.; Lorenzelli, L.; Dahiya, R.

    2015-12-01

    This work presents a novel manufacturing route for obtaining high performance bendable field effect transistors (FET) by embedding silicon (Si) microwires (2.5 μm thick) in layers of solution-processed dielectric and metallic layers. The objective of this study is to explore heterogeneous integration of Si with polymers and to exploit the benefits of both microelectronics and printing technologies. Arrays of Si microwires are developed on silicon on insulator (SOI) wafers and transfer printed to polyimide (PI) substrate through a polydimethylsiloxane (PDMS) carrier stamp. Following the transfer printing of Si microwires, two different processing steps were developed to obtain top gate top contact and back gate top contact FETs. Electrical characterizations indicate devices having mobility as high as 117.5 cm2 V-1 s-1. The fabricated devices were also modeled using SILVACO Atlas. Simulation results show a trend in the electrical response similar to that of experimental results. In addition, a cyclic test was performed to demonstrate the reliability and mechanical robustness of the Si μ-wires on flexible substrates.

  8. Dielectric elastomer based active layer for macro-scaled industrial application in roto-flexographic printing

    NASA Astrophysics Data System (ADS)

    Pinto, F.; D'Oriano, G.; Meo, M.

    2014-03-01

    The use of dielectric elastomer (DE) for the realisation of new generation actuators has attracted the interest of many researchers in the last ten years due to their high efficiency, a very good electromechanical coupling and large achievable strains [1-3]. Although these properties constitute a very important advantage, the industrial exploitation of such systems is hindered by the high voltages required for the actuation [4] that could potentially constitute also a risk for the operators. In this work we present a DE based active layer that can be used in different macro-scaled parts of industrial equipment for roto-flexographic printing substituting traditional mechanical devices, reducing manufacturing costs and enhancing its reliability. Moreover, the specific configuration of the system requires the driving voltage to be applied only in the mounting/dismounting step thus lowering further the operative costs without posing any threat for the workers. Starting from the industrial requirements, a complete thermo-mechanical characterisation using DSC and DMA was undertaken on acrylic elastomer films in order to investigate their behaviour under the operative frequencies and solicitations. Validation of the active layer was experimentally evaluated by manufacturing a DE actuator controlling both prestrain and nature of the complaint electrodes, and measuring the electrically induced Maxwell's strain using a laser vibrometer to evaluate the relative displacement along the z-axis.

  9. Spectrum splitting using multi-layer dielectric meta-surfaces for efficient solar energy harvesting

    NASA Astrophysics Data System (ADS)

    Yao, Yuhan; Liu, He; Wu, Wei

    2014-06-01

    We designed a high-efficiency dispersive mirror based on multi-layer dielectric meta-surfaces. By replacing the secondary mirror of a dome solar concentrator with this dispersive mirror, the solar concentrator can be converted into a spectrum-splitting photovoltaic system with higher energy harvesting efficiency and potentially lower cost. The meta-surfaces are consisted of high-index contrast gratings (HCG). The structures and parameters of the dispersive mirror (i.e. stacked HCG) are optimized based on finite-difference time-domain and rigorous coupled-wave analysis method. Our numerical study shows that the dispersive mirror can direct light with different wavelengths into different angles in the entire solar spectrum, maintaining very low energy loss. Our approach will not only improve the energy harvesting efficiency, but also lower the cost by using single junction cells instead of multi-layer tandem solar cells. Moreover, this approach has the minimal disruption to the existing solar concentrator infrastructures.

  10. Dual insulated-gate field-effect transistors with cadmium sulfide active layer and a laminated polymer dielectric

    NASA Astrophysics Data System (ADS)

    Meth, J. S.; Zane, S. G.; Nunes, G.

    2004-04-01

    We report the fabrication of dual insulated gate thin-film transistors with chemical-bath deposited cadmium sulfide active layers. The cadmium sulfide was deposited from solution onto thermally oxidized silicon wafers to form the first semiconductor-dielectric interface. The terpolymer poly(tetrafluoroethylene-co-vinylidenefluoride-co-propylene) was laminated onto the semiconductor to create the second semiconductor-dielectric interface. This device geometry allows direct comparison of the behavior of the accumulated charge at these two very different interfaces. The mobility values for these devices are in the 0.1-1 cm2/Vs range, while the on/off ratios vary from 102 to 105. The ability to laminate a dielectric to a semiconductor enables new processing routes for large area transistor arrays.

  11. Modification of electronic properties of top-gated graphene devices by ultrathin yttrium-oxide dielectric layers.

    PubMed

    Wang, Lin; Chen, Xiaolong; Wang, Yang; Wu, Zefei; Li, Wei; Han, Yu; Zhang, Mingwei; He, Yuheng; Zhu, Chao; Fung, Kwok Kwong; Wang, Ning

    2013-02-01

    We report the structure characterization and electronic property modification of single layer graphene (SLG) field-effect transistor (FET) devices top-gated using ultrathin Y(2)O(3) as dielectric layers. Based on the Boltzmann transport theory within variant screening, Coulomb scattering is confirmed quantitatively to be dominant in Y(2)O(3)-covered SLG and a very few short-range impurities have been introduced by Y(2)O(3). Both DC transport and AC capacitance measurements carried out at cryogenic temperatures demonstrate that the broadening of Landau levels is mainly due to the additional charged impurities and inhomogeneity of carriers induced by Y(2)O(3) layers. PMID:23263255

  12. From 3D view to 3D print

    NASA Astrophysics Data System (ADS)

    Dima, M.; Farisato, G.; Bergomi, M.; Viotto, V.; Magrin, D.; Greggio, D.; Farinato, J.; Marafatto, L.; Ragazzoni, R.; Piazza, D.

    2014-08-01

    In the last few years 3D printing is getting more and more popular and used in many fields going from manufacturing to industrial design, architecture, medical support and aerospace. 3D printing is an evolution of bi-dimensional printing, which allows to obtain a solid object from a 3D model, realized with a 3D modelling software. The final product is obtained using an additive process, in which successive layers of material are laid down one over the other. A 3D printer allows to realize, in a simple way, very complex shapes, which would be quite difficult to be produced with dedicated conventional facilities. Thanks to the fact that the 3D printing is obtained superposing one layer to the others, it doesn't need any particular work flow and it is sufficient to simply draw the model and send it to print. Many different kinds of 3D printers exist based on the technology and material used for layer deposition. A common material used by the toner is ABS plastics, which is a light and rigid thermoplastic polymer, whose peculiar mechanical properties make it diffusely used in several fields, like pipes production and cars interiors manufacturing. I used this technology to create a 1:1 scale model of the telescope which is the hardware core of the space small mission CHEOPS (CHaracterising ExOPlanets Satellite) by ESA, which aims to characterize EXOplanets via transits observations. The telescope has a Ritchey-Chrétien configuration with a 30cm aperture and the launch is foreseen in 2017. In this paper, I present the different phases for the realization of such a model, focusing onto pros and cons of this kind of technology. For example, because of the finite printable volume (10×10×12 inches in the x, y and z directions respectively), it has been necessary to split the largest parts of the instrument in smaller components to be then reassembled and post-processed. A further issue is the resolution of the printed material, which is expressed in terms of layers

  13. 3d-3d correspondence revisited

    NASA Astrophysics Data System (ADS)

    Chung, Hee-Joong; Dimofte, Tudor; Gukov, Sergei; Sułkowski, Piotr

    2016-04-01

    In fivebrane compactifications on 3-manifolds, we point out the importance of all flat connections in the proper definition of the effective 3d {N}=2 theory. The Lagrangians of some theories with the desired properties can be constructed with the help of homological knot invariants that categorify colored Jones polynomials. Higgsing the full 3d theories constructed this way recovers theories found previously by Dimofte-Gaiotto-Gukov. We also consider the cutting and gluing of 3-manifolds along smooth boundaries and the role played by all flat connections in this operation.

  14. Boosting the Transparency of Thin Layers by Coatings of Opposing Susceptibility: How Metals Help See Through Dielectrics.

    PubMed

    Al Shakhs, Mohammed; Augusto, Lucian; Markley, Loïc; Chau, Kenneth J

    2016-01-01

    We propose a hypothesis that a very thin layer can be made more transparent by adding a thin coating with susceptibility of opposing sign. Two experimental tests backed by a theoretical model support this hypothesis. First, we show that the visible and near-infrared transmission through a semi-transparent silver film can be enhanced by up to ~70% and spectrally tailored depending on the type and thickness of the dielectric coating. Material types explored as dielectric coating layers include conventional metal oxides (titanium dioxide) and lesser-explored elemental semiconductors (undoped silicon, p-type silicon, and germanium). Second, and more surprisingly, we show that coating a 50-nm-thick silicon nitride membrane with a 10-nm-thick silver layer can modestly enhance the transmission by up to 6 ± 1% in the blue part of the spectrum. Transmission enhancements are observed for three silver-coated membranes in different configurations. Thinner silver coatings are theoretically capable of enhancement factors greater than 10%, but implementation is restricted by challenges in making smooth and continuous silver films below 10 nm in thickness. This study is important because it is the first demonstration of reciprocity with respect to the transmission enhancements achieved by combining thin metallic and dielectric layers. PMID:26860979

  15. Boosting the Transparency of Thin Layers by Coatings of Opposing Susceptibility: How Metals Help See Through Dielectrics

    PubMed Central

    Shakhs, Mohammed Al; Augusto, Lucian; Markley, Loïc; Chau, Kenneth J.

    2016-01-01

    We propose a hypothesis that a very thin layer can be made more transparent by adding a thin coating with susceptibility of opposing sign. Two experimental tests backed by a theoretical model support this hypothesis. First, we show that the visible and near-infrared transmission through a semi-transparent silver film can be enhanced by up to ~70% and spectrally tailored depending on the type and thickness of the dielectric coating. Material types explored as dielectric coating layers include conventional metal oxides (titanium dioxide) and lesser-explored elemental semiconductors (undoped silicon, p-type silicon, and germanium). Second, and more surprisingly, we show that coating a 50-nm-thick silicon nitride membrane with a 10-nm-thick silver layer can modestly enhance the transmission by up to 6 ± 1% in the blue part of the spectrum. Transmission enhancements are observed for three silver-coated membranes in different configurations. Thinner silver coatings are theoretically capable of enhancement factors greater than 10%, but implementation is restricted by challenges in making smooth and continuous silver films below 10 nm in thickness. This study is important because it is the first demonstration of reciprocity with respect to the transmission enhancements achieved by combining thin metallic and dielectric layers. PMID:26860979

  16. Boosting the Transparency of Thin Layers by Coatings of Opposing Susceptibility: How Metals Help See Through Dielectrics

    NASA Astrophysics Data System (ADS)

    Shakhs, Mohammed Al; Augusto, Lucian; Markley, Loïc; Chau, Kenneth J.

    2016-02-01

    We propose a hypothesis that a very thin layer can be made more transparent by adding a thin coating with susceptibility of opposing sign. Two experimental tests backed by a theoretical model support this hypothesis. First, we show that the visible and near-infrared transmission through a semi-transparent silver film can be enhanced by up to ~70% and spectrally tailored depending on the type and thickness of the dielectric coating. Material types explored as dielectric coating layers include conventional metal oxides (titanium dioxide) and lesser-explored elemental semiconductors (undoped silicon, p-type silicon, and germanium). Second, and more surprisingly, we show that coating a 50-nm-thick silicon nitride membrane with a 10-nm-thick silver layer can modestly enhance the transmission by up to 6 ± 1% in the blue part of the spectrum. Transmission enhancements are observed for three silver-coated membranes in different configurations. Thinner silver coatings are theoretically capable of enhancement factors greater than 10%, but implementation is restricted by challenges in making smooth and continuous silver films below 10 nm in thickness. This study is important because it is the first demonstration of reciprocity with respect to the transmission enhancements achieved by combining thin metallic and dielectric layers.

  17. Assembly of a high-dielectric constant thin TiOx layer directly on H-terminated semiconductor diamond

    NASA Astrophysics Data System (ADS)

    Zhao, Jing; Liu, Jiangwei; Sang, Liwen; Liao, Meiyong; Coathup, David; Imura, Masataka; Shi, Baogui; Gu, Changzhi; Koide, Yasuo; Ye, Haitao

    2016-01-01

    A high-dielectric constant (high-k) TiOx thin layer was fabricated on hydrogen-terminated diamond (H-diamond) surface by low temperature oxidation of a thin titanium layer in ambient air. The metallic titanium layer was deposited by sputter deposition. The dielectric constant of the resultant TiOx was calculated to be around 12. The capacitance density of the metal-oxide-semiconductor (MOS) based on the TiOx/H-diamond was as high as 0.75 μF/cm2 contributed from the high-k value and the very thin thickness of the TiOx layer. The leakage current was lower than 10-13 A at reverse biases and 10-7A at the forward bias of -2 V. The MOS field-effect transistor based on the high-k TiOx/H-diamond was demonstrated. The utilization of the high-k TiOx with a very thin thickness brought forward the features of an ideally low subthreshold swing slope of 65 mV per decade and improved drain current at low gate voltages. The advantages of the utilization high-k dielectric for diamond metal-oxide semiconductor field effect transistors are anticipated.

  18. A rigorous theoretical model of guided waves excitation in a plane dielectric layer under electromagnetic diffraction by a conducting strip

    NASA Astrophysics Data System (ADS)

    Serdyuk, Vladimir M.; Titovitsky, Joseph A.

    2014-06-01

    An exact solution of two-dimensional problem of plane electromagnetic wave scattering by a perfectly conducting strip in the presence of a parallel plane dielectric layer is presented. The given solution is constructed using the mode-matching technique in the form of diffraction integrals over propagation parameter, i.e. in the form of superposition of a large number of homogeneous and inhomogeneous plane waves with continuous spectrum of spatial frequencies. These integrals have poles, which are caused by the presence of a transparent dielectric layer and correspond to its waveguide modes. Because of this, diffraction integrals need the procedure of regularization with explicit extraction of pole terms and smoothing of integrands, whereupon the residual diffraction integrals are computed using simple numerical methods. They describe usual scattered field of a bounded obstacle, which is determined by regularized diffraction integrals and decreases in all directions from an obstacle. Besides, the total diffraction field contains a discrete finite sum of waveguide fields of guided modes of a plane dielectric layer, which correspond to the extracted pole terms of initial diffraction integrals. These fields correspond to pairs of guided waves, which move apart from the region of their excitation near a strip, propagating parallel to the boundaries of a layer and conserving finite amplitude at infinity.

  19. Integration of atomic layer deposited high-k dielectrics on GaSb via hydrogen plasma exposure

    SciTech Connect

    Ruppalt, Laura B. Cleveland, Erin R.; Champlain, James G.; Bennett, Brian R.; Prokes, Sharka M.

    2014-12-15

    In this letter we report the efficacy of a hydrogen plasma pretreatment for integrating atomic layer deposited (ALD) high-k dielectric stacks with device-quality p-type GaSb(001) epitaxial layers. Molecular beam eptiaxy-grown GaSb surfaces were subjected to a 30 minute H{sub 2}/Ar plasma treatment and subsequently removed to air. High-k HfO{sub 2} and Al{sub 2}O{sub 3}/HfO{sub 2} bilayer insulating films were then deposited via ALD and samples were processed into standard metal-oxide-semiconductor (MOS) capacitors. The quality of the semiconductor/dielectric interface was probed by current-voltage and variable-frequency admittance measurements. Measurement results indicate that the H{sub 2}-plamsa pretreatment leads to a low density of interface states nearly independent of the deposited dielectric material, suggesting that pre-deposition H{sub 2}-plasma exposure, coupled with ALD of high-k dielectrics, may provide an effective means for achieving high-quality GaSb MOS structures for advanced Sb-based digital and analog electronics.

  20. Surface passivation and interface properties of bulk GaAs and epitaxial-GaAs/Ge using atomic layer deposited TiAlO alloy dielectric.

    PubMed

    Dalapati, G K; Chia, C K; Tan, C C; Tan, H R; Chiam, S Y; Dong, J R; Das, A; Chattopadhyay, S; Mahata, C; Maiti, C K; Chi, D Z

    2013-02-01

    High quality surface passivation on bulk-GaAs substrates and epitaxial-GaAs/Ge (epi-GaAs) layers were achieved by using atomic layer deposited (ALD) titanium aluminum oxide (TiAlO) alloy dielectric. The TiAlO alloy dielectric suppresses the formation of defective native oxide on GaAs layers. X-ray photoelectron spectroscopy (XPS) analysis shows interfacial arsenic oxide (As(x)O(y)) and elemental arsenic (As) were completely removed from the GaAs surface. Energy dispersive X-ray diffraction (EDX) analysis and secondary ion mass spectroscopy (SIMS) analysis showed that TiAlO dielectric is an effective barrier layer for reducing the out-diffusion of elemental atoms, enhancing the electrical properties of bulk-GaAs based metal-oxide-semiconductor (MOS) devices. Moreover, ALD TiAlO alloy dielectric on epi-GaAs with AlGaAs buffer layer realized smooth interface between epi-GaAs layers and TiAlO dielectric, yielding a high quality surface passivation on epi-GaAs layers, much sought-after for high-speed transistor applications on a silicon platform. Presence of a thin AlGaAs buffer layer between epi-GaAs and Ge substrates improved interface quality and gate dielectric quality through the reduction of interfacial layer formation (Ga(x)O(y)) and suppression of elemental out-diffusion (Ga and As). The AlGaAs buffer layer and TiAlO dielectric play a key role to suppress the roughening, interfacial layer formation, and impurity diffusion into the dielectric, which in turn largely enhances the electrical property of the epi-GaAs MOS devices. PMID:23331503

  1. Environmentally friendly power generator based on moving liquid dielectric and double layer effect

    PubMed Central

    Huynh, D. H.; Nguyen, T. C.; Nguyen, P. D.; Abeyrathne, C. D.; Hossain, Md. S.; Evans, R.; Skafidas, E.

    2016-01-01

    An electrostatic power generator converts mechanical energy to electrical energy by utilising the principle of variable capacitance. This change in capacitance is usually achieved by varying the gap or overlap between two parallel metallic plates. This paper proposes a novel electrostatic micro power generator where the change in capacitance is achieved by the movement of an aqueous solution of NaCl. A significant change in capacitance is achieved due to the higher than air dielectric constant of water and the Helmholtz double layer capacitor formed by ion separation at the electrode interfaces. The proposed device has significant advantages over traditional electrostatic devices which include low bias voltage and low mechanical frequency of operation. This is critical if the proposed device is to have utility in harvesting power from the environment. A figure of merit exceeding 10000(108μW)/(mm2HzV2) which is two orders of magnitude greater than previous devices, is demonstrated for a prototype operating at a bias voltage of 1.2 V and a droplet frequency of 6 Hz. Concepts are presented for large scale power harvesting. PMID:27255577

  2. Environmentally friendly power generator based on moving liquid dielectric and double layer effect

    NASA Astrophysics Data System (ADS)

    Huynh, D. H.; Nguyen, T. C.; Nguyen, P. D.; Abeyrathne, C. D.; Hossain, Md. S.; Evans, R.; Skafidas, E.

    2016-06-01

    An electrostatic power generator converts mechanical energy to electrical energy by utilising the principle of variable capacitance. This change in capacitance is usually achieved by varying the gap or overlap between two parallel metallic plates. This paper proposes a novel electrostatic micro power generator where the change in capacitance is achieved by the movement of an aqueous solution of NaCl. A significant change in capacitance is achieved due to the higher than air dielectric constant of water and the Helmholtz double layer capacitor formed by ion separation at the electrode interfaces. The proposed device has significant advantages over traditional electrostatic devices which include low bias voltage and low mechanical frequency of operation. This is critical if the proposed device is to have utility in harvesting power from the environment. A figure of merit exceeding 10000(108μW)/(mm2HzV2) which is two orders of magnitude greater than previous devices, is demonstrated for a prototype operating at a bias voltage of 1.2 V and a droplet frequency of 6 Hz. Concepts are presented for large scale power harvesting.

  3. Environmentally friendly power generator based on moving liquid dielectric and double layer effect.

    PubMed

    Huynh, D H; Nguyen, T C; Nguyen, P D; Abeyrathne, C D; Hossain, Md S; Evans, R; Skafidas, E

    2016-01-01

    An electrostatic power generator converts mechanical energy to electrical energy by utilising the principle of variable capacitance. This change in capacitance is usually achieved by varying the gap or overlap between two parallel metallic plates. This paper proposes a novel electrostatic micro power generator where the change in capacitance is achieved by the movement of an aqueous solution of NaCl. A significant change in capacitance is achieved due to the higher than air dielectric constant of water and the Helmholtz double layer capacitor formed by ion separation at the electrode interfaces. The proposed device has significant advantages over traditional electrostatic devices which include low bias voltage and low mechanical frequency of operation. This is critical if the proposed device is to have utility in harvesting power from the environment. A figure of merit exceeding 10000(10(8)μW)/(mm(2)HzV(2)) which is two orders of magnitude greater than previous devices, is demonstrated for a prototype operating at a bias voltage of 1.2 V and a droplet frequency of 6 Hz. Concepts are presented for large scale power harvesting. PMID:27255577

  4. Electrical behavior of atomic layer deposited high quality SiO{sub 2} gate dielectric

    SciTech Connect

    Pradhan, Sangram K.; Tanyi, Ekembu K.; Skuza, Jonathan R.; Xiao, Bo; Pradhan, Aswini K.

    2015-01-01

    Comprehensive and systematic electrical studies were performed on fabrication of high quality SiO{sub 2} thin films MOS capacitor using the robust, novel, and simple atomic layer deposition (ALD) technique using highly reactive ozone and tris (dimethylamino) silane (TDMAS) precursors. Ideal capacitance–voltage curve exhibits a very small frequency dispersion and hysteresis behavior of the SiO{sub 2} MOS capacitor grown at 1 s TDMAS pulse, suggesting excellent interfacial quality and purity of the film as probed using x-ray photoelectron studies. The flat-band voltage of the device shifted from negative toward positive voltage axis with increase of TDMAS pulses from 0.2 to 2 s. Based on an equivalent oxide thickness point of view, all SiO{sub 2} films have gate leakage current density of (5.18 × 10{sup −8} A/cm{sup 2}) as well as high dielectric break down fields of more than (∼10 MV/cm), which is better and comparable to that of thermally grown SiO{sub 2} at temperatures above 800 °C. These appealing electrical properties of ALD grown SiO{sub 2} thin films enable its potential applications such as high-quality gate insulators for thin film MOS transistors, as well as insulators for sensor and nanostructures on nonsilicon substrates.

  5. Facile synthesis of 3D few-layered MoS2 coated TiO2 nanosheet core-shell nanostructures for stable and high-performance lithium-ion batteries

    NASA Astrophysics Data System (ADS)

    Chen, Biao; Zhao, Naiqin; Guo, Lichao; He, Fang; Shi, Chunsheng; He, Chunnian; Li, Jiajun; Liu, Enzuo

    2015-07-01

    Uniform transition metal sulfide deposition on a smooth TiO2 surface to form a coating structure is a well-known challenge, caused mainly due to their poor affinities. Herein, we report a facile strategy for fabricating mesoporous 3D few-layered (<4 layers) MoS2 coated TiO2 nanosheet core-shell nanocomposites (denoted as 3D FL-MoS2@TiO2) by a novel two-step method using a smooth TiO2 nanosheet as a template and glucose as a binder. The core-shell structure has been systematically examined and corroborated by transmission electron microscopy, scanning transmission electron microscopy, and X-ray photoelectron spectroscopy analyses. It is found that the resultant 3D FL-MoS2@TiO2 as a lithium-ion battery anode delivers an outstanding high-rate capability with an excellent cycling performance, relating to the unique structure of 3D FL-MoS2@TiO2. The 3D uniform coverage of few-layered (<4 layers) MoS2 onto the TiO2 can remarkably enhance the structure stability and effectively shortens the transfer paths of both lithium ions and electrons, while the strong synergistic effect between MoS2 and TiO2 can significantly facilitate the transport of ions and electrons across the interfaces, especially in the high-rate charge-discharge process. Moreover, the facile fabrication strategy can be easily extended to design other oxide/carbon-sulfide/oxide core-shell materials for extensive applications.Uniform transition metal sulfide deposition on a smooth TiO2 surface to form a coating structure is a well-known challenge, caused mainly due to their poor affinities. Herein, we report a facile strategy for fabricating mesoporous 3D few-layered (<4 layers) MoS2 coated TiO2 nanosheet core-shell nanocomposites (denoted as 3D FL-MoS2@TiO2) by a novel two-step method using a smooth TiO2 nanosheet as a template and glucose as a binder. The core-shell structure has been systematically examined and corroborated by transmission electron microscopy, scanning transmission electron microscopy

  6. Facile synthesis of 3D few-layered MoS₂ coated TiO₂ nanosheet core-shell nanostructures for stable and high-performance lithium-ion batteries.

    PubMed

    Chen, Biao; Zhao, Naiqin; Guo, Lichao; He, Fang; Shi, Chunsheng; He, Chunnian; Li, Jiajun; Liu, Enzuo

    2015-08-14

    Uniform transition metal sulfide deposition on a smooth TiO2 surface to form a coating structure is a well-known challenge, caused mainly due to their poor affinities. Herein, we report a facile strategy for fabricating mesoporous 3D few-layered (<4 layers) MoS2 coated TiO2 nanosheet core-shell nanocomposites (denoted as 3D FL-MoS2@TiO2) by a novel two-step method using a smooth TiO2 nanosheet as a template and glucose as a binder. The core-shell structure has been systematically examined and corroborated by transmission electron microscopy, scanning transmission electron microscopy, and X-ray photoelectron spectroscopy analyses. It is found that the resultant 3D FL-MoS2@TiO2 as a lithium-ion battery anode delivers an outstanding high-rate capability with an excellent cycling performance, relating to the unique structure of 3D FL-MoS2@TiO2. The 3D uniform coverage of few-layered (<4 layers) MoS2 onto the TiO2 can remarkably enhance the structure stability and effectively shortens the transfer paths of both lithium ions and electrons, while the strong synergistic effect between MoS2 and TiO2 can significantly facilitate the transport of ions and electrons across the interfaces, especially in the high-rate charge-discharge process. Moreover, the facile fabrication strategy can be easily extended to design other oxide/carbon-sulfide/oxide core-shell materials for extensive applications. PMID:26165623

  7. Improvement in the breakdown endurance of high-κ dielectric by utilizing stacking technology and adding sufficient interfacial layer

    PubMed Central

    2014-01-01

    Improvement in the time-zero dielectric breakdown (TZDB) endurance of metal-oxide-semiconductor (MOS) capacitor with stacking structure of Al/HfO2/SiO2/Si is demonstrated in this work. The misalignment of the conduction paths between two stacking layers is believed to be effective to increase the breakdown field of the devices. Meanwhile, the resistance of the dielectric after breakdown for device with stacking structure would be less than that of without stacking structure due to a higher breakdown field and larger breakdown power. In addition, the role of interfacial layer (IL) in the control of the interface trap density (Dit) and device reliability is also analyzed. Device with a thicker IL introduces a higher breakdown field and also a lower Dit. High-resolution transmission electron microscopy (HRTEM) of the samples with different IL thicknesses is provided to confirm that IL is needed for good interfacial property. PMID:25246869

  8. 3D and Education

    NASA Astrophysics Data System (ADS)

    Meulien Ohlmann, Odile

    2013-02-01

    Today the industry offers a chain of 3D products. Learning to "read" and to "create in 3D" becomes an issue of education of primary importance. 25 years professional experience in France, the United States and Germany, Odile Meulien set up a personal method of initiation to 3D creation that entails the spatial/temporal experience of the holographic visual. She will present some different tools and techniques used for this learning, their advantages and disadvantages, programs and issues of educational policies, constraints and expectations related to the development of new techniques for 3D imaging. Although the creation of display holograms is very much reduced compared to the creation of the 90ies, the holographic concept is spreading in all scientific, social, and artistic activities of our present time. She will also raise many questions: What means 3D? Is it communication? Is it perception? How the seeing and none seeing is interferes? What else has to be taken in consideration to communicate in 3D? How to handle the non visible relations of moving objects with subjects? Does this transform our model of exchange with others? What kind of interaction this has with our everyday life? Then come more practical questions: How to learn creating 3D visualization, to learn 3D grammar, 3D language, 3D thinking? What for? At what level? In which matter? for whom?

  9. Discrete hexamer water clusters and 2D water layer trapped in three luminescent Ag/tetramethylpyrazine/benzene-dicarboxylate hosts: 1D chain, 2D layer and 3D network

    NASA Astrophysics Data System (ADS)

    Mei, Hong-Xin; Zhang, Ting; Huang, Hua-Qi; Huang, Rong-Bin; Zheng, Lan-Sun

    2016-03-01

    Three mix-ligand Ag(I) coordination compounds, namely, {[Ag10(tpyz) 5(L1) 5(H2 O)2].(H2 O)4}n (1, tpyz = 2,3,4,5-tetramethylpyrazine, H2 L1 = phthalic acid), [Ag4(tpyz) 2(L2) 2(H2 O)].(H2 O)5}n (2, H2 L2 = isophthalic acid) {[Ag2(tpyz) 2(L3) (H2 O)4].(H2 O)8}n (3, H2 L3 = terephthalic acid), have been synthesized and characterized by elemental analysis, IR, PXRD and X-ray single-crystal diffraction. 1 exhibits a 2D layer which can be simplified as a (4,4) net. 2 is a 3D network which can be simplified as a (3,3)-connected 2-nodal net with a point symbol of {102.12}{102}. 3 consists of linear [Ag(tpyz) (H2 O)2]n chain. Of particular interest, discrete hexamer water clusters were observed in 1 and 2, while a 2D L10(6) water layer exists in 3. The results suggest that the benzene dicarboxylates play pivotal roles in the formation of the different host architectures as well as different water aggregations. Moreover, thermogravimetric analysis (TGA) and emissive behaviors of these compounds were investigated.

  10. Effect of surface waves on the characteristics of a linear phased array in the presence of a dielectric layer

    NASA Astrophysics Data System (ADS)

    Kniazev, S. T.; Panchenko, B. A.

    A Green-function approach is taken to the determination of the surface-wave spectrum for a phased array with a dielectric layer, taking into account the relationship between bulk and surface waves. Numerical results are presented on the radiation characteristics of a linear phased array consisting of strip dipoles. Dipole input admittance and bulk-wave admittance are determined as a function of phasing angle.

  11. Dielectric response of double layered perovskite Sr3MnTiO7

    NASA Astrophysics Data System (ADS)

    Chowki, S.; Sahu, B.; Singh, A. K.; Mohapatra, N.

    2016-05-01

    The results of dielectric and resistivity measurements on the Ruddlesden-Popper (RP) type compound Sr3MnTiO7 (SMTO) is presented here. The dielectric response of the compound was recorded in the temperature range 10-300 K with the probing frequency from 500 Hz-5 MHz. We observe a broad anomaly at ~ 200 K in the temperature dependence of dissipation factor (tanδ) and corresponding change in slope in the dielectric constant ɛr'(T) which may be attributed to a difference in the conduction mechanism below and above 200 K. The overall dielectric dispersion of SMTO resembles to that of the double perovskites Sr2MnTiO6 and La2NiMnO6 which follows the modified Debye relaxation equation. This indicates a relaxor type dielectric behavior of SMTO may be due to the contribution of grain boundary effects.

  12. Dielectric Bilayer Films Comprising Polar Cyanolated Silica Sol-Gel and Nanoscale Blocking Layer for Energy Storage Applications

    NASA Astrophysics Data System (ADS)

    Kathaperumal, Mohanalingam; Kim, Yunsang; Smith, O'neil; Dindar, Amir; Fuentes-Hernandez, Canek; Hwang, Do-Kyung; Pan, Ming-Jen; Kippelen, Bernard; Perry, Joseph

    2013-03-01

    Organic-inorganic hybrid sol-gel containing polar groups, which can undergo orientational polarization under the influence of an electric field, provide a potential route to processable and rational design of materials for energy storage applications. However, the porous nature of sol-gel films, which significantly lowers breakdown strength, limits the potential of this material for energy storage particularly in high-field applications. In this work, we fabricate and characterize dielectric bilayer films comprising cyanolated silica sol-gel film prepared from 2-cyanoethyltrimethoxysilane (CNETMS) precursor and nanoscale blocking layers, which include amorphous fluoropolymer, SiO2, Al2O3 and ZrO2 deposited by spin casting, electron beam evaporation or atomic layer deposition (ALD). CNETMS films with 50 nm ZrO2 blocking layer exhibit an extractable energy density of 13 J/cm3, which is about a twofold enhancement compared to CNETMS films without blocking layer. The effect of the blocking layer will be discussed in terms of surface morphology, dielectric contrast, i.e. the ratio of relative permittivity between oxide layer and sol-gel film, electric field distribution, breakdown strength and statistics, bias polarity, and loss of the bilayer films.

  13. Shim3d Helmholtz Solution Package

    2009-01-29

    This suite of codes solves the Helmholtz Equation for the steady-state propagation of single-frequency electromagnetic radiation in an arbitrary 2D or 3D dielectric medium. Materials can be either transparent or absorptive (including metals) and are described entirely by their shape and complex dielectric constant. Dielectric boundaries are assumed to always fall on grid boundaries and the material within a single grid cell is considered to be uniform. Input to the problem is in the formmore » of a Dirichlet boundary condition on a single boundary, and may be either analytic (Gaussian) in shape, or a mode shape computed using a separate code (such as the included eigenmode solver vwave20), and written to a file. Solution is via the finite difference method using Jacobi iteration for 3D problems or direct matrix inversion for 2D problems. Note that 3D problems that include metals will require different iteration parameters than described in the above reference. For structures with curved boundaries not easily modeled on a rectangular grid, the auxillary codes helmholtz11(2D), helm3d (semivectoral), and helmv3d (full vectoral) are provided. For these codes the finite difference equations are specified on a topological regular triangular grid and solved using Jacobi iteration or direct matrix inversion as before. An automatic grid generator is supplied.« less

  14. 'Diamond' in 3-D

    NASA Technical Reports Server (NTRS)

    2004-01-01

    This 3-D, microscopic imager mosaic of a target area on a rock called 'Diamond Jenness' was taken after NASA's Mars Exploration Rover Opportunity ground into the surface with its rock abrasion tool for a second time.

    Opportunity has bored nearly a dozen holes into the inner walls of 'Endurance Crater.' On sols 177 and 178 (July 23 and July 24, 2004), the rover worked double-duty on Diamond Jenness. Surface debris and the bumpy shape of the rock resulted in a shallow and irregular hole, only about 2 millimeters (0.08 inch) deep. The final depth was not enough to remove all the bumps and leave a neat hole with a smooth floor. This extremely shallow depression was then examined by the rover's alpha particle X-ray spectrometer.

    On Sol 178, Opportunity's 'robotic rodent' dined on Diamond Jenness once again, grinding almost an additional 5 millimeters (about 0.2 inch). The rover then applied its Moessbauer spectrometer to the deepened hole. This double dose of Diamond Jenness enabled the science team to examine the rock at varying layers. Results from those grindings are currently being analyzed.

    The image mosaic is about 6 centimeters (2.4 inches) across.

  15. The impact of non-local buoyancy flux on the convective boundary layer development as simulated by a 3-D TKE-based subgrid mixing scheme in a mesoscale model

    NASA Astrophysics Data System (ADS)

    Zhang, Xu; Bao, Jian-Wen; Chen, Baode

    2016-04-01

    This presentation highlights a study in which a series of dry convective boundary layer (CBL) simulations are carried out using a generalized 3-dimensional (3-D) TKE-based parameterization scheme of sub-grid turbulent mixing in the Weather Research and Forecasting (WRF) model. The simulated characteristics of dry CBL are analyzed for the purpose of evaluating this scheme in comparison with a commonly-used scheme for sub-grid turbulent mixing in NWP models (i.e., the Mellor-Yamada 1.5-order TKE scheme). The same surface layer scheme is used in all the simulations so that only the sensitivity of the WRF model to different parameterizations of the sub-grid turbulent mixing above the surface layer is examined. The effect of horizontal grid resolution on the simulated CBL is also examined by running the model with grid sizes of 200, 400 m, 600 m, 1 km and 3 km. We will first compare the characteristics of the simulated CBL using the two schemes with the WRF LES dataset. We will then illustrate the importance of including the non-local component in the vertical buoyancy specification in the 3-D TKE-based scheme. Finally, comparing the results from the simulations against coarse-grained WRF LES dataset, we will show the feasibility and advantage of replacing conventional planetary boundary layer parameterization schemes with a scale-aware 3-D TKE-based scheme in the WRF model.

  16. On FAST3D simulations of directly-driven inertial-fusion targets with high-Z layers for reducing laser imprint and surface non-uniformity growth

    NASA Astrophysics Data System (ADS)

    Bates, Jason; Schmitt, Andrew; Klapisch, Marcel; Karasik, Max; Obenschain, Steve

    2013-10-01

    Modifications to the FAST3D code have been made to enhance its ability to simulate the dynamics of plastic ICF targets with high-Z overcoats. This class of problems is challenging computationally due in part to plasma conditions that are not in a state of local thermodynamic equilibrium and to the presence of mixed computational cells containing more than one material. Recently, new opacity tables for gold, palladium and plastic have been generated with an improved version of the STA code. These improved tables provide smoother, higher-fidelity opacity data over a wider range of temperature and density states than before, and contribute to a more accurate treatment of radiative transfer processes in FAST3D simulations. Furthermore, a new, more efficient subroutine known as ``MMEOS'' has been installed in the FAST3D code for determining pressure and temperature equilibrium conditions within cells containing multiple materials. We will discuss these topics, and present new simulation results for high-Z planar-target experiments performed recently on the NIKE Laser Facility. Work supported by DOE/NNSA.

  17. 3D Imaging.

    ERIC Educational Resources Information Center

    Hastings, S. K.

    2002-01-01

    Discusses 3 D imaging as it relates to digital representations in virtual library collections. Highlights include X-ray computed tomography (X-ray CT); the National Science Foundation (NSF) Digital Library Initiatives; output peripherals; image retrieval systems, including metadata; and applications of 3 D imaging for libraries and museums. (LRW)

  18. Melt front propagation in dielectrics upon femtosecond laser irradiation: Formation dynamics of a heat-affected layer

    NASA Astrophysics Data System (ADS)

    Garcia-Lechuga, Mario; Solis, Javier; Siegel, Jan

    2016-04-01

    Several studies in dielectrics have reported the presence of a thin heat-affected layer underneath the ablation crater produced by femtosecond laser irradiation. In this work, we present a time-resolved microscopy technique that is capable of monitoring the formation dynamics of this layer and apply it to the study of a phosphate glass exposed to single pulses below the ablation threshold. A few nanoseconds after laser excitation, a melt front interface can be detected, which propagates into the bulk, gradually slowing down its speed. By means of image analysis combined with optical modeling, we are able to determine the temporal evolution of the layer thickness and its refractive index. Initially, a strong transient decrease in the refractive index is observed, which partially recovers afterwards. The layer resolidifies after approximately 1 μs after excitation, featuring a maximum thickness of several hundreds of nanometers.

  19. Simulation and evaluation of dielectric and magnetoelectric properties of diphasic and layered ferroic composites

    NASA Astrophysics Data System (ADS)

    Wang, Hsiao-Yuan

    The present demand in the development of tunable devices and meta-materials require better understanding of the composite systems. Ferroelectric based composites with solubility or impurities doped interstitially satisfied the specific condition necessary for applications of e.g. frequency, bias, temperature, etc. On the other hand, many composite materials using coupling phenomena have been reported to have their effective properties surpassing the natural materials. The improvement of the properties of composite materials lies on the better understanding of their coupling effects. Conventional science tries to derive theories based on observation and materials characterizations. Taken advantage of the rapid growing computer technology, one used to say "impossible to be measured" or "impossible to see" can now be virtually characterized and visualized by simulation models. In this thesis, computer models of dielectric properties, piezoelectricity, magnetostriction and magnetoelectricity were constructed and verified. And subsequently the materials of interest were simulated and discussed. First, a three dimensional finite element model on dielectric properties of two phases or materials mixture was constructed. The effective permittivity and tan(delta) of Ba0.5Sr0.5 TiO3:MgO composite were simulated and compared with the experimental results. Structural design parameters concepts such as layers stacking, geometry effect, and effect of size of inclusion were visualized and then discussed. Subsequently, dielectric properties of Ba0.5Sr0.5TiO 3:MgO composite were examined changing their volume fraction using Monte Carlo simulation. The type of connectivity of the Ba0.5Sr 0.5TiO3:MgO composite was also discussed. On the other hand, finite element method with Monte Carlo simulation was conducted for the composition (x)Pb0.2Sr0.8TiO3:(1-x)MgO from x=0 to 1 in the paraelectric phase (from -50°C to 200°C), and the results were computed and compared with the experimental

  20. The effect of inorganic/organic dual dielectric layers on the morphology and performance of n-channel OFETs.

    PubMed

    Kalita, Anamika; Dey, Anamika; Iyer, Parameswar Krishnan

    2016-04-28

    The optimization of dual dielectric layers by incorporating poly(vinyl alcohol) (PVA), poly(methyl methacrylate) (PMMA), polystyrene (PS) or poly(4-vinylphenol) (PVP) in combination with Al2O3 resulted in immensely improved OFET characteristics with N,N'-bis(cyclohexyl)naphthalene diimide (NDI-CY2) as the active material. The influence of the polymer dielectric layer on the growth morphology of NDI-CY2 and the structural characterization were investigated using atomic force microscopy (AFM) and thin film XRD analysis. The bottom-gate top-contact OFET devices fabricated on glass substrates with Al contact electrodes demonstrated excellent n-channel behavior in the presence of the Al2O3/PVA dual dielectric with the highest electron mobility (μe) value of 0.08 cm(2) V(-1) s(-1), threshold voltage (VTH) as low as 0.5 V and current on/off ratio (ION/IOFF) of 10(4) with an operating voltage of 5 V respectively under vacuum. PMID:27075922

  1. 7-Octenyltrichrolosilane/trimethyaluminum hybrid dielectrics fabricated by molecular-atomic layer deposition on ZnO thin film transistors

    NASA Astrophysics Data System (ADS)

    Huang, Jie; Lee, Mingun; Lucero, Antonio T.; Cheng, Lanxia; Ha, Min-Woo; Kim, Jiyoung

    2016-06-01

    We demonstrate the fabrication of 7-octenytrichlorosilane (7-OTS)/trimethylaluminum (TMA) organic–inorganic hybrid films using molecular-atomic layer deposition (MALD). The properties of 7-OTS/TMA hybrid films are extensively investigated using transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), atomic force microscopy (AFM), and electrical measurements. Our results suggest that uniform and smooth amorphous hybrid thin films with excellent insulating properties are obtained using the MALD process. Films have a relatively high dielectric constant of approximately 5.0 and low leakage current density. We fabricate zinc oxide (ZnO) based thin film transistors (TFTs) using 7-OTS/TMA hybrid material as a back gate dielectric with the top ZnO channel layer deposited in-situ via MALD. The ZnO TFTs exhibit a field effect mobility of approximately 0.43 cm2 V‑1 s‑1, a threshold voltage of approximately 1 V, and an on/off ratio of approximately 103 under low voltage operation (from ‑3 to 9 V). This work demonstrates an organic–inorganic hybrid gate dielectric material potentially useful in flexible electronics application.

  2. Recent developments in multi-layer flat knitting technology for waste free production of complex shaped 3D-reinforcing structures for composites

    NASA Astrophysics Data System (ADS)

    Trümper, W.; Lin, H.; Callin, T.; Bollengier, Q.; Cherif, C.; Krzywinski, S.

    2016-07-01

    Constantly increasing prices for raw materials and energy as well as the current discourse on the reduction of CO2-emissions places a special emphasis on the advantages of lightweight constructions and its resource conserving production methods. Fibre-reinforced composites are already seeing a number of applications in automobile, energy and mechanical engineering. Future applications within the named areas require greater material and energy efficiency and therefore manufacturing methods for textile preforms and lightweight constructions enabling an optimal arrangement of the reinforcing fibres while in the same time limiting waste to a minimum. One manufacturing method for textile reinforced preforms fulfilling quite many of the named requirements is the multilayer weft knitting technology. Multilayer weft knitted fabrics containing straight reinforcing yarns at least in two directions. The arrangement of these yarns is fixed by the loop yarn. Used yarn material in each knitting row is adaptable e. g. according to the load requirements or for the local integration of sensors. Draping properties of these fabrics can be varied within a great range and through this enabling draping of very complex shaped 3D-preforms without wrinkles from just one uncut fabric. The latest developments at ITM are concentrating on the development of a full production chain considering the 3D-CAD geometry, the load analysis, the generation of machine control programs as well as the development of technology and machines to enable the manufacturing of innovative net shape 3D-multilayer weft knitted fabrics such as complex shaped spacer fabrics and tubular fabrics with biaxial reinforcement.

  3. Enhancement-mode operation of multilayer MoS2 transistors with a fluoropolymer gate dielectric layer

    NASA Astrophysics Data System (ADS)

    Yoo, Geonwook; Choi, Sol Lea; Lee, Suelbe; Yoo, Byungwook; Kim, Sunkook; Oh, Min Suk

    2016-06-01

    Enhancement-mode multilayer molybdenum disulfide (MoS2) field-effect transistors (FETs), which are an immensely important component toward low-power electronics based on a two-dimensional layered semiconductor, are demonstrated using the fluoropolymer CYTOP as a gate dielectric. The fabricated devices exhibit threshold voltage (VTH) of ˜5.7 V with field-effect mobility (μFE) of up to 82.3 cm2/V s, and the characteristics are compared with the depletion-mode characteristics of MoS2 FETs with the cross-linked Poly(4-vinylphenol) gate dielectric (VTH ˜ -7.8 V). UV photoelectron spectroscopy analysis indicates that increased surface potential due to the surface dipole effect of the fluorine group influences the positive VTH shift.

  4. A method to fabricate disconnected silver nanostructures in 3D.

    PubMed

    Vora, Kevin; Kang, SeungYeon; Mazur, Eric

    2012-01-01

    The standard nanofabrication toolkit includes techniques primarily aimed at creating 2D patterns in dielectric media. Creating metal patterns on a submicron scale requires a combination of nanofabrication tools and several material processing steps. For example, steps to create planar metal structures using ultraviolet photolithography and electron-beam lithography can include sample exposure, sample development, metal deposition, and metal liftoff. To create 3D metal structures, the sequence is repeated multiple times. The complexity and difficulty of stacking and aligning multiple layers limits practical implementations of 3D metal structuring using standard nanofabrication tools. Femtosecond-laser direct-writing has emerged as a pre-eminent technique for 3D nanofabrication.(1,2) Femtosecond lasers are frequently used to create 3D patterns in polymers and glasses.(3-7) However, 3D metal direct-writing remains a challenge. Here, we describe a method to fabricate silver nanostructures embedded inside a polymer matrix using a femtosecond laser centered at 800 nm. The method enables the fabrication of patterns not feasible using other techniques, such as 3D arrays of disconnected silver voxels.(8) Disconnected 3D metal patterns are useful for metamaterials where unit cells are not in contact with each other,(9) such as coupled metal dot(10,11)or coupled metal rod(12,13) resonators. Potential applications include negative index metamaterials, invisibility cloaks, and perfect lenses. In femtosecond-laser direct-writing, the laser wavelength is chosen such that photons are not linearly absorbed in the target medium. When the laser pulse duration is compressed to the femtosecond time scale and the radiation is tightly focused inside the target, the extremely high intensity induces nonlinear absorption. Multiple photons are absorbed simultaneously to cause electronic transitions that lead to material modification within the focused region. Using this approach, one can

  5. Effects of the interfacial layer on electrical characteristics of Al 2O 3/TiO 2/Al 2O 3 thin films for gate dielectrics

    NASA Astrophysics Data System (ADS)

    Kim, Chang Eun; Yun, Ilgu

    2012-01-01

    Effects of thermal annealing on the electrical properties of Al2O3/TiO2/Al2O3 (ATA) dielectric thin films prepared by atomic layer deposition are investigated. The structural properties and chemical states in the interfacial layer are analyzed with varying the annealing temperature. The dielectric constant and leakage current are affected by the formation of Al2O3-TiO2 composite and interfacial layer including SiOx in the interface by the annealing. The transformation of interfacial layer at the interface of the ATA/Si substrate due to the annealing is a critical point to apply ATA thin films as gate dielectric layers.

  6. Formation of a Refracted Electromagnetic Wave at the Output from a Plane-Parallel Dielectric Layer and Interference Nature of Fermat's Principle

    NASA Astrophysics Data System (ADS)

    Averbukh, B. B.; Averbukh, I. B.

    2015-04-01

    It is shown that a transition layer representing a spatial region in which field propagation is analogous to refraction in an inhomogeneous medium exists after a dielectric layer. In this region located within the near field zone the direction of the wave vector of the transmitted field varies smoothly, and with increasing distance from the layer, approaches to that of the wave incident on the layer. It is shown that such behavior of the field and occurrence of the transition layer are caused by the interference of the incident wave field and the fields of secondary sources excited in the dielectric by the incident wave field. It is shown that the refraction of the field in a homogeneous medium after the dielectric corresponds to Fermat's principle, and the interference nature of Fermat's principle is justified.

  7. Three-Dimensional Boundary-Layer program (BL3D) for swept subsonic or supersonic wings with application to laminar flow control

    NASA Technical Reports Server (NTRS)

    Iyer, Venkit

    1993-01-01

    The theory, formulation, and solution of three-dimensional, compressible attached laminar flows, applied to swept wings in subsonic or supersonic flow are discussed. Several new features and modifications to an earlier general procedure described in NASA CR 4269, Jan. 1990 are incorporated. Details of interfacing the boundary-layer computation with solution of the inviscid Euler equations are discussed. A description of the computer program, complete with user's manual and example cases, is also included. Comparison of solutions with Navier-Stokes computations with or without boundary-layer suction is given. Output of solution profiles and derivatives required in boundary-layer stability analysis is provided.

  8. Gamma-radiation-induced dielectric relaxation characteristics of layered crystals of phlogopite mica

    NASA Astrophysics Data System (ADS)

    Kaur, Navjeet; Singh, Mohan; Singh, Lakhwant; Awasthi, A. M.; Kumar, Jitender

    2013-12-01

    In the present investigation, the influence of gamma irradiation on the dielectric relaxation characteristics of phlogopite mica was studied over the frequency range of 0.1 Hz-10 MHz and in the temperature range of 593-813 K by measuring the dielectric permittivity, electric modulus and conductivity. By comparing the dielectric spectra obtained for pristine and irradiated samples, it was observed that gamma irradiation significantly enhances the dielectric constants (ɛ‧ and ɛ″) of phlogopite mica because of the production of defects and lattice disorder by the gamma irradiation. The values of the activation energy for pristine and irradiated mica (determined from the electric modulus and the conductivity) were found to be substantially similar, suggesting that the same types of charge carriers are involved in the relaxation mechanism. The experimentally measured electric modulus and conductivity data could be well interpreted by the Havriliak-Negami dielectric relaxation function. The scaling of the electric-modulus spectra of both pristine and irradiated mica results in a master curve, which indicates that the relaxation mechanism is independent of temperature. Cole-Cole plots were also employed to analyze the non-Debye relaxation mechanism. This research will boost the reader's interest concerning the emerging contributions of irradiation and materials such as mica in electrical engineering.

  9. TRACE 3-D documentation

    SciTech Connect

    Crandall, K.R.

    1987-08-01

    TRACE 3-D is an interactive beam-dynamics program that calculates the envelopes of a bunched beam, including linear space-charge forces, through a user-defined transport system. TRACE 3-D provides an immediate graphics display of the envelopes and the phase-space ellipses and allows nine types of beam-matching options. This report describes the beam-dynamics calculations and gives detailed instruction for using the code. Several examples are described in detail.

  10. Atomic Layer Deposition of a High-k Dielectric on MoS2 Using Trimethylaluminum and Ozone

    PubMed Central

    2015-01-01

    We present an Al2O3 dielectric layer on molybdenum disulfide (MoS2), deposited using atomic layer deposition (ALD) with ozone/trimethylaluminum (TMA) and water/TMA as precursors. The results of atomic force microscopy and low-energy ion scattering spectroscopy show that using TMA and ozone as precursors leads to the formation of uniform Al2O3 layers, in contrast to the incomplete coverage we observe when using TMA/H2O as precursors. Our Raman and X-ray photoelectron spectroscopy measurements indicate minimal variations in the MoS2 structure after ozone treatment at 200 °C, suggesting its excellent chemical resistance to ozone. PMID:25025335

  11. Reflective three-port high-efficiency grating with two dielectric layers based on a sandwiched configuration

    NASA Astrophysics Data System (ADS)

    Li, Hongtao; Wang, Bo; Pei, Hao; Shu, Wenhao; Chen, Li; Lei, Liang; Zhou, Jinyun

    2016-04-01

    In this paper, we describe a novel reflective sandwiched three-port grating with two dielectric layers. The two-layer sandwiched grating can separate incident wave into the ± 1 and the 0th-order with high-efficiency beam splitting and good splitting ratios for both transverse electric (TE) and transverse magnetic (TM) polarizations. The grating parameters can be optimized by using rigorous coupled-wave analysis (RCWA) with a special duty cycle of 0.6. With the optimized results, efficiencies more than 32% in the ± 1st-orders and the 0th-order can be obtained. Furthermore, performance of the incident bandwidth and aspect ratio can be improved. Compared with conventional surface-relief grating, the grating with sandwiched structure is aimed at cleaning and protecting grating surface. The presented reflective two-layer sandwiched three-port grating would be put into practical applications for its beneficial performances.

  12. Facile synthesis 3D flexible core-shell graphene/glass fiber via chemical vapor deposition

    NASA Astrophysics Data System (ADS)

    Yang, Cheng; Xu, Yuanyuan; Zhang, Chao; Sun, Zhencui; Chen, Chuansong; Li, Xiuhua; Jiang, Shouzhen; Man, Baoyuan

    2014-08-01

    Direct deposition of graphene layers on the flexible glass fiber surface to form the three-dimensional (3D) core-shell structures is offered using a two-heating reactor chemical vapor deposition system. The two-heating reactor is utilized to offer sufficient, well-proportioned floating C atoms and provide a facile way for low-temperature deposition. Graphene layers, which are controlled by changing the growth time, can be grown on the surface of wire-type glass fiber with the diameter from 30 nm to 120 um. The core-shell graphene/glass fiber deposition mechanism is proposed, suggesting that the 3D graphene films can be deposited on any proper wire-type substrates. These results open a facile way for direct and high-efficiency deposition of the transfer-free graphene layers on the low-temperature dielectric wire-type substrates.

  13. Investigation of MOS Interfaces with Atomic-Layer-Deposited High-k Gate Dielectrics on III-V Semiconductors

    NASA Astrophysics Data System (ADS)

    Suri, Rahul

    The purpose of this research work was to investigate the surface passivation methods and metal gate/high-k dielectric gate stacks for metal-oxide-semiconductor devices (MOS) on III-V compound semiconductor materials -- (i) GaAs for future high-speed low-power logic devices and (ii) AlGaN/GaN heterostructure for future high-speed high-power devices. GaAs is a candidate material for high-mobility channel in a NMOS transistor to extend the CMOS scaling up to and beyond the 16-nm technology node. AlGaN/GaN heterostructure is useful in a MOS-high electron mobility transistor (MOS-HEMT) device for providing a high current-carrying two dimensional electron gas (2DEG) channel. The interaction of GaAs surface with atomic layer deposition of high- k dielectrics was investigated to gain fundamental insights into the chemical properties of GaAs surface oxides and high-k/GaAs interface. Electrical characterization of devices was performed to understand the impact of high-k/GaAs interface on MOS device characteristics in order to form a suitable metal/high-k/GaAs gatestack for future high-speed logic and power devices. Reduction of native oxides on GaAs was found to occur during atomic layer deposition (ALD) of high-k dielectrics- HfO2 and Al2O3/HfO 2 nanolaminates on GaAs. Reaction between ALD metal precursor and native oxides on GaAs was identified to be the cause for consumption of native oxides. It was established that the ALD growth temperature has a strong impact on this phenomenon. During post-dielectric annealing the residual arsenic oxides at the interface decomposed leading to an increase in the interfacial gallium oxides. Presence of gallium oxide, Ga2O3 was identified as a cause for observed frequency dispersion in MOS capacitance-voltage curves indicative of a high interface state density. The chemical properties of the AlGaN/GaN heterostructure surface prepared by wet chemical treatment using HCl/HF and NH4OH solutions were investigated and compared. Both HCl and

  14. Reflectance and substrate currents of dielectric layers under vacuum ultraviolet irradiation

    SciTech Connect

    Sinha, H.; Straight, D. B.; Lauer, J. L.; Fuller, N. C.; Engelmann, S. U.; Zhang, Y.; Antonelli, G. A.; Severson, M.; Nishi, Y.; Shohet, J. L.

    2010-11-15

    The reflectance of low-k porous organosilicate glass (SiCOH) as a function of photon energy under synchrotron vacuum ultraviolet (VUV) radiation was measured using a nickel mesh reflectometer. The authors found that during VUV irradiation, the reflectance of SiCOH and the substrate current were inversely correlated. Thus, reflectance can be inferred from substrate current measurements and vice versa. The authors conclude that reflectance or substrate current measurements can determine the photon energies that are absorbed and, therefore, cause dielectric damage during processing. Thus, reducing the flux of deleterious photon energies in processing systems can minimize dielectric damage.

  15. Effects of the dielectric environment on the electron transport properties of single-layer MoS2

    NASA Astrophysics Data System (ADS)

    Bertolazzi, Simone; Allain, Adrien; Lembke, Dominik; Kis, Andras

    2014-03-01

    Two-dimensional materials, such as graphene, boron nitride and transition metal dichalcogenides, offer a wide range of electronic, optical and mechanical properties that can be advantageous for several applications in nanotechnology. Among these materials, single-layer molybdenum disulfide (MoS2) shows great potential for scaling field-effect transistor devices, due to an optimal electrostatic control of the 2D semiconducting sheet, large energy bandgap and minimal leakage currents. However, to fully exploit the potential of this atomically thin semiconductor, additional experimental efforts need to be undertaken to boost the device performance and access the theoretical intrinsic electron mobilities. To pursue this objective, it is mandatory to reduce the density of charged impurities, both in the semiconducting sheet and in its surrounding environment, and to limit carrier scattering induced by polar optical phonons in the dielectric surface. Here we present the results of our recent experimental investigation of the electron transport properties of single-layer MoS2 mechanically exfoliated/transferred onto different substrates, with varying surface chemistry, surface roughness and dielectric permittivity. We will show temperature-dependent four-terminal measurements of the electrical conductivity of single-layer MoS2 in contact with various insulating materials, including 2D sheets of hexagonal boron nitride, organic polymers and metal oxides.

  16. Nucleation and growth of dielectric films on III-V semiconductors during atomic layer deposition

    NASA Astrophysics Data System (ADS)

    Granados Alpizar, Bernal

    In order to continue with metal-oxide-semiconductors (CMOS) transistor scaling and to reduce the power density, the channel should be replaced with a material having a higher electron mobility, such as a III-V semiconductor. However, the integration of III-V's is a challenge because these materials oxidize rapidly when exposed to air and the native oxide produced is characterized by a high density of defects. Deposition of high-k materials on III-V semiconductors using Atomic Layer Deposition (ALD) reduces the thickness of these oxides, improving the semiconductor/oxide interface quality and the transistor electrical characteristics. In this work, ALD is used to deposit two dielectrics, Al 2O3 and TiO2, on two III-V materials, GaAs and InGaAs, and in-situ X-ray photoelectron spectroscopy (XPS) and in-situ thermal programmed desorption (TPD) are used for interface characterization. Hydrofluoric acid (HF) etching of GaAs(100) and brief reoxidation in air produces a 9.0 ±1.6 Å-thick oxide overlayer containing 86% As oxides. The oxides are removed by 1 s pulses of trimethylaluminum (TMA) or TiCl4. TMA removes the oxide overlayer while depositing a 7.5 ± 1.6 Å thick aluminum oxide. The reaction follows a ligand exchange mechanism producing nonvolatile Al-O species that remain on the surface. TiCl4 exposure removes the oxide overlayer in the temperature range 89°C to 300°C, depositing approximately 0.04 monolayer of titanium oxide for deposition temperatures from 89°C to 135°C, but no titanium oxide is present from 170 °C to 230 °C. TiCl4 forms a volatile oxychloride product and removes O from the surface while leaving Cl atoms adsorbed to an elemental As layer, chemically passivating the surface. The native oxide of In0.53Ga0.47As(100) is removed using liquid HF and gas phase HF before deposition of Al2O3 using TMA and H2O at 170 °C. An aluminium oxide film with a thickness of 7.2 ± 1.2 Å and 7.3 ± 1.2 Å is deposited during the first pulse of TMA on

  17. The dispersion in accumulation at InGaAs-based metal/oxide/semiconductor gate stacks with a bi-layered dielectric structure

    NASA Astrophysics Data System (ADS)

    Krylov, Igor; Ritter, Dan; Eizenberg, Moshe

    2015-08-01

    InGaAs gate stacks comprising the moderate dielectric constant (k) Al2O3 have a significantly lower dispersion in accumulation in comparison to stacks with the high-k HfO2 of the same physical thickness. As a result, a HfO2/Al2O3 bi-layer structure seems attractive in terms of both high effective dielectric constant and low dispersion in accumulation. The influence of Al2O3 thickness on the dispersion was investigated in metal/HfO2/Al2O3/InGaAs gate stacks with a fixed overall dielectric thickness. An effective suppression of the dispersion with the increase of the Al2O3 thickness was observed. However, the Al2O3 thickness required for passivation of the dispersion in accumulation was significantly higher in comparison to both the border traps related tunneling distance in Al2O3 and the minimal thickness required for the Al2O3/InGaAs band offset stabilization. The phenomenon can be explained by the lower dielectric constant of Al2O3 film (compared to the subsequently deposited HfO2 layer), where Al2O3 dielectric constant dependence on the film thickness enhances the dispersion intensity. As a result, the guidelines for the passivation layer engineering are: maximization of both majority carriers band offsets and of the dielectric constant of the passivation layer.

  18. Neutron powder diffraction study of the layer organic-inorganic hybrid iron(II) methylphosphonate-hydrate, Fe[(CD{sub 3}PO{sub 3})(D{sub 2}O)

    SciTech Connect

    Leone, Philippe Bellitto, Carlo; Bauer, Elvira M.; Righini, Guido; Andre, Gilles; Bouree, Francoise

    2008-11-15

    The crystal and magnetic structures of the hybrid organic-inorganic layer compound Fe[(CD{sub 3}PO{sub 3})(D{sub 2}O)] have been studied by neutron powder diffraction as a function of temperature down to 1.5 K. The neutron diffraction pattern recorded at 200 K shows that the fully deuterated compound crystallizes in one of the two known forms of the undeuterated Fe[(CH{sub 3}PO{sub 3})(H{sub 2}O)]. The crystal structure is orthorhombic, space group Pmn2{sub 1}, with the following unit-cell parameters: a=5.7095(1) A, b=8.8053(3) A and c=4.7987(1) A; Z=2. The crystal structure remains unchanged on cooling from 200 to 1.5 K. Moreover, at low temperature, Fe[(CD{sub 3}PO{sub 3})(D{sub 2}O)] shows a commensurate magnetic structure (k=(0,0,0)). As revealed by bulk susceptibility measurements on Fe[(CH{sub 3}PO{sub 3})(H{sub 2}O)], the magnetic structure corresponds to a canted antiferromagnet with a critical temperature T{sub N}=25 K. Neutron powder diffraction reveals that below T{sub N}=23.5 K the iron magnetic moments in Fe[(CD{sub 3}PO{sub 3})(D{sub 2}O)] are antiferromagnetically coupled and oriented along the b-axis, perpendicular to the inorganic layers. No ferromagnetic component is observable in the neutron powder diffraction experiment, due to its too small value (<0.1{mu}{sub B}). - Graphical abstract: Crystal structure and magnetic structure of Fe[(CD{sub 3}PO{sub 3})(D{sub 2}O)].

  19. GTD analysis of airborne antennas radiating in the presence of lossy dielectric layers

    NASA Technical Reports Server (NTRS)

    Rojas-Teran, R. G.; Burnside, W. D.

    1981-01-01

    The patterns of monopole or aperture antennas mounted on a perfectly conducting convex surface radiating in the presence of a dielectric or metal plate are computed. The geometrical theory of diffraction is used to analyze the radiating system and extended here to include diffraction by flat dielectric slabs. Modified edge diffraction coefficients valid for wedges whose walls are lossy or lossless thin dielectric or perfectly conducting plates are developed. The width of the dielectric plates cannot exceed a quarter of a wavelength in free space, and the interior angle of the wedge is assumed to be close to 0 deg or 180 deg. Systematic methods for computing the individual components of the total high frequency field are discussed. The accuracy of the solutions is demonstrated by comparisons with measured results, where a 2 lambda by 4 lambda prolate spheroid is used as the convex surface. A jump or kink appears in the calculated pattern when higher order terms that are important are not included in the final solution. The most immediate application of the results presented here is in the modelling of structures such as aircraft which are composed of nonmetallic parts that play a significant role in the pattern.

  20. 3D-graphite structure

    SciTech Connect

    Belenkov, E. A. Ali-Pasha, V. A.

    2011-01-15

    The structure of clusters of some new carbon 3D-graphite phases have been calculated using the molecular-mechanics methods. It is established that 3D-graphite polytypes {alpha}{sub 1,1}, {alpha}{sub 1,3}, {alpha}{sub 1,5}, {alpha}{sub 2,1}, {alpha}{sub 2,3}, {alpha}{sub 3,1}, {beta}{sub 1,2}, {beta}{sub 1,4}, {beta}{sub 1,6}, {beta}{sub 2,1}, and {beta}{sub 3,2} consist of sp{sup 2}-hybridized atoms, have hexagonal unit cells, and differ in regards to the structure of layers and order of their alternation. A possible way to experimentally synthesize new carbon phases is proposed: the polymerization and carbonization of hydrocarbon molecules.

  1. Al{sub 2}O{sub 3} as a suitable substrate and a dielectric layer for n-layer MoS{sub 2}

    SciTech Connect

    Singh, Arunima K. Davydov, Albert V.; Tavazza, Francesca; Hennig, Richard G.

    2015-08-03

    Sapphire (α-Al{sub 2}O{sub 3}) is a common substrate for the growth of single- to few-layer MoS{sub 2} films, and amorphous aluminium oxide serves as a high-κ dielectric gate oxide for MoS{sub 2} based transistors. Using density-functional theory calculations with a van der Waals functional, we investigate the structural, energetic, and electronic properties of n-layer MoS{sub 2} (n = 1and 3) on the α-Al{sub 2}O{sub 3} (0001) surface. Our results show that the sapphire stabilizes single-layer and tri-layer MoS{sub 2}, while having a negligible effect on the structure, band gap, and electron effective masses of MoS{sub 2}. This combination of a strong energetic stabilization and weak perturbation of the electronic properties shows that α-Al{sub 2}O{sub 3} can serve as an ideal substrate for depositing ultra-thin MoS{sub 2} layers and can also serve as a passivation or gate-oxide layer for MoS{sub 2} based devices.

  2. Improved dielectric properties of lead zirconate titanate thin films deposited on metal foils with LaNiO3 buffer layers

    NASA Astrophysics Data System (ADS)

    Zou, Q.; Ruda, H. E.; Yacobi, B. G.

    2001-02-01

    Improved dielectric properties of lead zirconate titanate (PZT) films deposited on a variety of foils using buffer layers are reported. Foils include titanium, stainless steel, and nickel with LaNiO3(LNO) buffer layers which were prepared by sol-gel processing. High dielectric constant (330 for stainless steel, 420 for titanium, and 450 for nickel foils), low dielectric loss (<2.2% for titanium and 8% for stainless steel), symmetric ferroelectric C-V characteristics and P-E curves were obtained. The LNO layers are shown to provide an effective diffusion barrier for Ni and Cr and to restrict oxide layer formation (i.e., TiOx or NiOx) between the PZT film and the metallic foils during annealing in air.

  3. Transformation from a 2D stacked layer to 3D interpenetrated framework by changing the spacer functionality: synthesis, structure, adsorption, and magnetic properties.

    PubMed

    Maji, Tapas Kumar; Ohba, Masaaki; Kitagawa, Susumu

    2005-12-12

    Two novel coordination polymers of Cu(II), viz. [Cu(bipy)(1,4-napdc)(H2O)2]n and {[Cu(bpe)1.5(1,4-napdc)](H2O)}n (bipy=4,4'-bipyridine; bpe=1,2-bis(4-pyridyl)ethane; 1,4-napdc2-=1,4-naphthalenedicarboxylate), have been synthesized and structurally characterized by changing only the pillar motifs. Both the compounds crystallize by slow evaporation from the ammoniacal solution of the as-synthesized solid. Framework 1 crystallizes in monoclinic crystal system, space group P2/n (No. 13), with a=11.028(19) A, b=11.16(3) A, c=7.678(13) A, beta=103.30(5) degrees, and Z=2. Framework 2 crystallizes in triclinic system, space group, P (No. 2), a=10.613(4) A, b=10.828(10) A, c=13.333(9) A, alpha=85.25(9) degrees, beta=82.59(6) degrees, gamma=60.37(5) degrees, and Z=2. The structure determination reveals that has a 2D network based on rectangular grids, where each Cu(II) is in 4+2 coordination mode. The 2D networks stacked in a staggered manner through the pi-pi interaction to form a 3D supramolecular network. In the case of, a {Cu(bpe)1.5}n ladder connected by 1,4-napdc2- results a 2D cuboidal bilayer network and each bilayer network is interlocked by two adjacent identical network (upper and lower) forming 3-fold interpenetrated 3D framework with small channel along the c-axis, which accommodates two water molecules. The TGA and XRPD measurements reveal that both the frameworks are stable after dehydration. Adsorption measurements (N2, CO2, and different solvents, like H2O, MeOH, etc.) were carried out for both frameworks. Framework shows type-II sorption profile with N2 in contrast to H2O and MeOH, which are chemisorbed in the framework. In case of, only H2O molecules can diffuse into the micropore, whereas N2, CO2, and MeOH cannot be adsorbed, as corroborated by the smaller channel aperture. The low-temperature (300-2 K) magnetic measurement of and reveals that both are weakly antiferromagnetically coupled (J=-1.85 cm-1, g=2.02; J=-0.153 cm-1, g=2.07), which is correlated

  4. A high capacity 3D steganography algorithm.

    PubMed

    Chao, Min-Wen; Lin, Chao-hung; Yu, Cheng-Wei; Lee, Tong-Yee

    2009-01-01

    In this paper, we present a very high-capacity and low-distortion 3D steganography scheme. Our steganography approach is based on a novel multilayered embedding scheme to hide secret messages in the vertices of 3D polygon models. Experimental results show that the cover model distortion is very small as the number of hiding layers ranges from 7 to 13 layers. To the best of our knowledge, this novel approach can provide much higher hiding capacity than other state-of-the-art approaches, while obeying the low distortion and security basic requirements for steganography on 3D models. PMID:19147891

  5. Radiochromic 3D Detectors

    NASA Astrophysics Data System (ADS)

    Oldham, Mark

    2015-01-01

    Radiochromic materials exhibit a colour change when exposed to ionising radiation. Radiochromic film has been used for clinical dosimetry for many years and increasingly so recently, as films of higher sensitivities have become available. The two principle advantages of radiochromic dosimetry include greater tissue equivalence (radiologically) and the lack of requirement for development of the colour change. In a radiochromic material, the colour change arises direct from ionising interactions affecting dye molecules, without requiring any latent chemical, optical or thermal development, with important implications for increased accuracy and convenience. It is only relatively recently however, that 3D radiochromic dosimetry has become possible. In this article we review recent developments and the current state-of-the-art of 3D radiochromic dosimetry, and the potential for a more comprehensive solution for the verification of complex radiation therapy treatments, and 3D dose measurement in general.

  6. Bootstrapping 3D fermions

    NASA Astrophysics Data System (ADS)

    Iliesiu, Luca; Kos, Filip; Poland, David; Pufu, Silviu S.; Simmons-Duffin, David; Yacoby, Ran

    2016-03-01

    We study the conformal bootstrap for a 4-point function of fermions < ψψψψ> in 3D. We first introduce an embedding formalism for 3D spinors and compute the conformal blocks appearing in fermion 4-point functions. Using these results, we find general bounds on the dimensions of operators appearing in the ψ × ψ OPE, and also on the central charge C T . We observe features in our bounds that coincide with scaling dimensions in the GrossNeveu models at large N . We also speculate that other features could coincide with a fermionic CFT containing no relevant scalar operators.

  7. On the location and stability of charge in SiO{sub 2}/SiN{sub x} dielectric double layers used for silicon surface passivation

    SciTech Connect

    Bonilla, Ruy S. Wilshaw, Peter R.; Reichel, Christian; Hermle, Martin

    2014-04-14

    Dielectric double layers of thermal silicon dioxide–chemical vapour deposition (CVD) silicon nitride are found to produce excellent passivation of silicon surfaces by combining a chemical reduction of surface defect states, with a field effect reduction of carriers at the surface due to charge in the dielectrics. The charge present in such double-layers has previously been attributed to be characteristic of the interface between the two. However, experimental evidence shows this is indirect and inconclusive. This manuscript reports direct measurements that show the charge lies within 10 nm of the interface between passivating double layers of thermal silicon dioxide–plasma CVD silicon nitride. In addition, the passivation efficiency of oxide-nitride layers, deposited using optimised conditions, was found to be largely unaffected by extra charge subsequently added to the film. The passivation efficiency of textured surfaces or those produced using non-optimised deposition conditions is found to be highly dependent on the field effect component provided by extra deposited charge. Using such extra field effect component, surface recombination velocities <2 cm/s have been obtained on single oxide and oxide/nitride double layers. The extra deposited charge was found to have good long term stability when the dielectric films are submitted to a chemical treatment. By contrast, poor stability of the deposited charge was observed when subjected to ultraviolet radiation. These results point to the importance of the interface between dielectrics when considering how to optimise the charge present in passivating dielectric films.

  8. Reduction of aerodynamic friction drag of moving bodies using a Microwave-Dielectric-Barrier-Discharge actuator controlling the boundary layer

    NASA Astrophysics Data System (ADS)

    Pierre, Thiery

    2015-11-01

    A new plasma device named M-DBD (Microwave Dielectric Barrier Discharge) is used for controlling the boundary layer in order to reduce the drag force. A compact resonant UHF structure comprising a resonant element in the form of a quarter-wave antenna creates a mini-plasma insulated from the UHF electrodes by mica sheets. Additional electrodes induce an electric field in the plasma and transiently move the ions of the plasma. The high collision rate with the neutral molecules induce the global transient flow of the neutral gas. The temporal variation of the applied electric field is chosen in order to obtain a modification of the local boundary layer. First tests using an array of M-DBD plasma actuators are underway (see Patent ref. WO 2014111469 A1).

  9. Reduced Dielectric Screening and Enhanced Energy Transfer in Single- and Few-Layer MoS2

    NASA Astrophysics Data System (ADS)

    Prins, Ferry; Goodman, Aaron J.; Tisdale, William A.

    2014-11-01

    We report highly efficient non-radiative energy transfer from cadmium selenide (CdSe) quantum dots to monolayer and few-layer molybdenum disulfide (MoS2). The quenching of the donor quantum dot photoluminescence increases as the MoS2 flake thickness decreases, with the highest efficiency (>95%) observed for monolayer MoS2. This counterintuitive result arises from reduced dielectric screening in thin layer semiconductors having unusually large permittivity and a strong in-plane transition dipole moment, as found in MoS2. Excitonic energy transfer between a 0D emitter and a 2D absorber is fundamentally interesting and enables a wide range of applications including broadband optical down-conversion, optical detection, photovoltaic sensitization, and color shifting in light-emitting devices.

  10. Reduced dielectric screening and enhanced energy transfer in single- and few-layer MoS2.

    PubMed

    Prins, Ferry; Goodman, Aaron J; Tisdale, William A

    2014-11-12

    We report highly efficient nonradiative energy transfer from cadmium selenide (CdSe) quantum dots to monolayer and few-layer molybdenum disulfide (MoS2). The quenching of the donor quantum dot photoluminescence increases as the MoS2 flake thickness decreases with the highest efficiency (>95%) observed for monolayer MoS2. This counterintuitive result arises from reduced dielectric screening in thin layer semiconductors having unusually large permittivity and a strong in-plane transition dipole moment, as found in MoS2. Excitonic energy transfer between a zero-dimensional emitter and a two-dimensional absorber is fundamentally interesting and enables a wide range of applications including broadband optical down-conversion, optical detection, photovoltaic sensitization, and color shifting in light-emitting devices. PMID:25289461

  11. Effect of selected atomic layer deposition parameters on the structure and dielectric properties of hafnium oxide films

    NASA Astrophysics Data System (ADS)

    Kukli, Kaupo; Aarik, Jaan; Ritala, Mikko; Uustare, Teet; Sajavaara, Timo; Lu, Jun; Sundqvist, Jonas; Aidla, Aleks; Pung, Lembit; Hârsta, Anders; Leskelä, Markku

    2004-11-01

    HfO2 films were atomic layer deposited from HfCl4 and H2O on Si(100) in the temperature range of 226-750°C. The films consisted of dominantly the monoclinic polymorph. Elastic recoil detection analysis revealed high residual chlorine and hydrogen contents (2-5at.%) in the films grown below 300-350°C. The content of residual hydrogen and chlorine monotonously decreased with increasing growth temperature. The effective permittivity insignificantly depended on the growth temperature and water partial pressure. Capacitance-voltage curves exhibited marked hysteresis especially in the films grown at 400-450°C, and demonstrated enhanced distortions likely due to the increased trap densities in the films grown at 700-750°C. Changes in water pressure led to some changes in the extent of crystallization, but did not induce any clear changes in the capacitance of the dielectric layer.

  12. Accuracy and efficiency in computing electrostatic potential for an ion channel model in layered dielectric/electrolyte media

    NASA Astrophysics Data System (ADS)

    Lin, Huimin; Tang, Huazhong; Cai, Wei

    2014-02-01

    This paper will investigate the numerical accuracy and efficiency in computing the electrostatic potential for a finite-height cylinder, used in an explicit/implicit hybrid solvation model for ion channel and embedded in a layered dielectric/electrolyte medium representing a biological membrane and ionic solvents. A charge locating inside the cylinder cavity, where ion channel proteins and ions are given explicit atomistic representations, will be influenced by the polarization field of the surrounding implicit dielectric/electrolyte medium. Two numerical techniques, a specially designed boundary integral equation method and an image charge method, will be investigated and compared in terms of accuracy and efficiency for computing the electrostatic potential. The boundary integral equation method based on the three-dimensional layered Green's functions provides a highly accurate solution suitable for producing a benchmark reference solution, while the image charge method is found to give reasonable accuracy and highly efficient and viable to use the fast multipole method for interactions of a large number of charges in the atomistic region of the hybrid solvation model.

  13. Accuracy and efficiency in computing electrostatic potential for an ion channel model in layered dielectric/electrolyte media

    SciTech Connect

    Lin, Huimin; Tang, Huazhong; Cai, Wei

    2014-02-15

    This paper will investigate the numerical accuracy and efficiency in computing the electrostatic potential for a finite-height cylinder, used in an explicit/implicit hybrid solvation model for ion channel and embedded in a layered dielectric/electrolyte medium representing a biological membrane and ionic solvents. A charge locating inside the cylinder cavity, where ion channel proteins and ions are given explicit atomistic representations, will be influenced by the polarization field of the surrounding implicit dielectric/electrolyte medium. Two numerical techniques, a specially designed boundary integral equation method and an image charge method, will be investigated and compared in terms of accuracy and efficiency for computing the electrostatic potential. The boundary integral equation method based on the three-dimensional layered Green's functions provides a highly accurate solution suitable for producing a benchmark reference solution, while the image charge method is found to give reasonable accuracy and highly efficient and viable to use the fast multipole method for interactions of a large number of charges in the atomistic region of the hybrid solvation model.

  14. Ray tracing of multiple transmitted/reflected/converted waves in 2-D/3-D layered anisotropic TTI media and application to crosswell traveltime tomography

    NASA Astrophysics Data System (ADS)

    Bai, Chao-Ying; Huang, Guo-Jiao; Li, Xiao-Ling; Zhou, Bing; Greenhalgh, Stewart

    2013-11-01

    To overcome the deficiency of some current grid-/cell-based ray tracing algorithms, which are only able to handle first arrivals or primary reflections (or conversions) in anisotropic media, we have extended the functionality of the multistage irregular shortest-path method to 2-D/3-D tilted transversely isotropic (TTI) media. The new approach is able to track multiple transmitted/reflected/converted arrivals composed of any kind of combinations of transmissions, reflections and mode conversions. The basic principle is that the seven parameters (five elastic parameters plus two polar angles defining the tilt of the symmetry axis) of the TTI media are sampled at primary nodes, and the group velocity values at secondary nodes are obtained by tri-linear interpolation of the primary nodes across each cell, from which the group velocities of the three wave modes (qP, qSV and qSH) are calculated. Finally, we conduct grid-/cell-based wave front expansion to trace multiple transmitted/reflected/converted arrivals from one region to the next. The results of calculations in uniform anisotropic media indicate that the numerical results agree with the analytical solutions except in directions of SV-wave triplications, at which only the lowest velocity value is selected at the singularity points by the multistage irregular shortest-path anisotropic ray tracing method. This verifies the accuracy of the methodology. Several simulation results show that the new method is able to efficiently and accurately approximate situations involving continuous velocity variations and undulating discontinuities, and that it is suitable for any combination of multiple transmitted/reflected/converted arrival tracking in TTI media of arbitrary strength and tilt. Crosshole synthetic traveltime tomographic tests have been performed, which highlight the importance of using such code when the medium is distinctly anisotropic.

  15. High-Tc superconducting rectangular microstrip patch covered with a dielectric layer

    NASA Astrophysics Data System (ADS)

    Bedra, Sami; Fortaki, Tarek

    2016-05-01

    This paper presents a full-wave method to calculate the resonant characteristics of rectangular microstrip antenna with and without dielectric cover, to explain the difference of performance with temperature between superconducting and normal conducting antenna. Especially the characteristics of high temperature superconducting (HTS) antenna were almost ideal around the critical temperature (Tc). The dyadic Green's functions of the considered structure are efficiently determined in the vector Fourier transform domain. The effect of the superconductivity of the patch is taken into account using the concept of the complex resistive boundary condition. The computed results are found to be in good agreement with results obtained using other methods. Also, the effects of the superstrate on the resonant frequency and bandwidth of rectangular microstrip patch in a substrate-superstrate configuration are investigated. This type of configuration can be used for wider bandwidth by proper selection of superstrate thickness and its dielectric constants.

  16. Effect of Carbon in the Dielectric Fluid and Workpieces on the Characteristics of Recast Layers Machined by Electrical Discharge Machining

    NASA Astrophysics Data System (ADS)

    Muttamara, Apiwat; Kanchanomai, Chaosuan

    2016-06-01

    Electrical discharge machining (EDM) is a popular non-traditional machining technique that is usually performed in kerosene. Carbon from the kerosene is mixed into the recast layer during EDM, increasing its hardness. EDM can be performed in deionized water, which causes decarburization. We studied the effects of carbon in the dielectric fluid and workpiece on the characteristics of recast layers. Experiments were conducted using gray cast iron and mild steel workpieces in deionized water or kerosene under identical operating conditions. Scanning electron microscopy revealed that the recast layer formed on gray iron was rougher than that produced on mild steel. Moreover, the dispersion of graphite flakes in the gray iron seemed to cause subsurface cracks, even when EDM was performed in deionized water. Dendritic structures and iron carbides were found in the recast layer of gray iron treated in deionized water. Kerosene caused more microcracks to form and increased surface roughness compared with deionized water. The microcrack length per unit area of mild steel treated in deionized water was greater than that treated in kerosene, but the cracks formed in kerosene were wider. The effect of the diffusion of carbon during cooling on the characteristics of the recast layer was discussed.

  17. High-Efficiency 800 nm Multi-Layer Dielectric Gratings for High Average Power Laser Systems

    SciTech Connect

    Nguyen, H T; Britten, J A; Patel, D; Brizuela, F; Rocca, J J; Menoni, C S

    2006-06-15

    We report on the design, fabrication, and performance of a 1740 l/mm multilayer dielectric diffraction grating for use with 800 nm light. At an input angle of 8{sup o} from Littrow and a wavelength from 770 to 830 nm, >90% diffraction efficiency is achieved, with peak diffraction efficiency of >97% at 800nm. We will also comment on laser damage threshold and power-handling properties.

  18. Interpenetration of a 3D Icosahedral M@Ni12 (M=Al, Ga) Framework with Porphyrin-Reminiscent Boron Layers in MNi9 B8.

    PubMed

    Zheng, Qiang; Wagner, Frank R; Ormeci, Alim; Prots, Yurii; Burkhardt, Ulrich; Schmidt, Marcus; Schnelle, Walter; Grin, Yuri; Leithe-Jasper, Andreas

    2015-11-01

    Two ternary borides MNi9 B8 (M=Al, Ga) were synthesized by thermal treatment of mixtures of the elements. Single-crystal X-ray diffraction data reveal AlNi9 B8 and GaNi9 B8 crystallizing in a new type of structure within the space group Cmcm and the lattice parameters a=7.0896(3) Å, b=8.1181(3) Å, c=10.6497(4) Å and a=7.0897(5) Å, b=8.1579(4) Å, c=10.6648(7) Å, respectively. The boron atoms build up two-dimensional layers, which consist of puckered [B16 ] rings with two tailing B atoms, whereas the M atoms reside in distorted vertices-condensed [Ni12 ] icosahedra, which form a three-dimensional framework interpenetrated by boron porphyrin-reminiscent layers. An unusual local arrangement resembling a giant metallo-porphyrin entity is formed by the [B16 ] rings, which, due to their large annular size of approximately 8 Å, chelate four of the twelve icosahedral Ni atoms. An analysis of the chemical bonding by means of the electron localizability approach reveals strong covalent B-B interactions and weak Ni-Ni interactions. Multi-center dative B-Ni interaction occurs between the Al-Ni framework and the boron layers. In agreement with the chemical bonding analysis and band structure calculations, AlNi9 B8 is a Pauli-paramagnetic metal. PMID:26418894

  19. A modified and stable version of a perfectly matched layer technique for the 3-d second order wave equation in time domain with an application to aeroacoustics

    PubMed Central

    Kaltenbacher, Barbara; Kaltenbacher, Manfred; Sim, Imbo

    2013-01-01

    We consider the second order wave equation in an unbounded domain and propose an advanced perfectly matched layer (PML) technique for its efficient and reliable simulation. In doing so, we concentrate on the time domain case and use the finite-element (FE) method for the space discretization. Our un-split-PML formulation requires four auxiliary variables within the PML region in three space dimensions. For a reduced version (rPML), we present a long time stability proof based on an energy analysis. The numerical case studies and an application example demonstrate the good performance and long time stability of our formulation for treating open domain problems. PMID:23888085

  20. A modified and stable version of a perfectly matched layer technique for the 3-d second order wave equation in time domain with an application to aeroacoustics.

    PubMed

    Kaltenbacher, Barbara; Kaltenbacher, Manfred; Sim, Imbo

    2013-02-15

    We consider the second order wave equation in an unbounded domain and propose an advanced perfectly matched layer (PML) technique for its efficient and reliable simulation. In doing so, we concentrate on the time domain case and use the finite-element (FE) method for the space discretization. Our un-split-PML formulation requires four auxiliary variables within the PML region in three space dimensions. For a reduced version (rPML), we present a long time stability proof based on an energy analysis. The numerical case studies and an application example demonstrate the good performance and long time stability of our formulation for treating open domain problems. PMID:23888085

  1. A modified and stable version of a perfectly matched layer technique for the 3-d second order wave equation in time domain with an application to aeroacoustics

    NASA Astrophysics Data System (ADS)

    Kaltenbacher, Barbara; Kaltenbacher, Manfred; Sim, Imbo

    2013-02-01

    We consider the second order wave equation in an unbounded domain and propose an advanced perfectly matched layer (PML) technique for its efficient and reliable simulation. In doing so, we concentrate on the time domain case and use the finite-element (FE) method for the space discretization. Our un-split-PML formulation requires four auxiliary variables within the PML region in three space dimensions. For a reduced version (rPML), we present a long time stability proof based on an energy analysis. The numerical case studies and an application example demonstrate the good performance and long time stability of our formulation for treating open domain problems.

  2. Two axes of the human eye and inversion of the retinal layers: the basis for the interpretation of the retina as a phase-grating-optical cellular 3D chip

    NASA Astrophysics Data System (ADS)

    Lauinger, Norbert

    1994-10-01

    The question of why the human eye has two axes, a photopic visual axis and an eye axis, is just as justified as the one of why the fovea is not on the eye axis, but instead is on the visual axis. An optical engineer would have omitted the second axis and placed the fovea on the eye axis. The answer to the question of why the design of the real eye differs from the logic of the engineer is found in its prenatal development. The biaxial design was the only possible consequence of the decision to invert the retinal layers. Accordingly, this is of considerable importance. It in turn forms the basis of the interpretation of the retinal nuclear layers as a cellular 3D phase grating, and can provide a diffraction-optical interpretation of adaptive effects (Purkinje shift), aperture phenomena (Stiles-Crawford effects I and II) in photopic vision, and visual acuity data in photopic and scotopic vision.

  3. K2Pb3(CO3)3F2 and KCdCO3F: Novel Fluoride Carbonates with Layered and 3D Framework Structures.

    PubMed

    Lin, Yuan; Hu, Chun-Li; Mao, Jiang-Gao

    2015-11-01

    Two new mixed metal fluoride carbonates, KCdCO3F and K2Pb3(CO3)3F2, have been synthesized by solvothermal and solid-state techniques. KCdCO3F crystallizes in the acentric nonpolar space group P6̅m2, and its structure features a three-dimensional anionic framework in which the CdCO3 layers are further interconnected by bridging F(-) anions with the negative charge balanced by K(+) cations. K2Pb3(CO3)3F2 crystallizes in the centrosymmetric space group P63/mmc, and its structure exhibits a layered anionic skeleton featuring corner-shared PbO6F and PbO6F2 polyhedra. UV-vis diffuse reflectance spectroscopy studies show that the short-wavelength absorption edges of KCdCO3F and K2Pb3(CO3)3F2 are 227 and 287 nm, respectively. The second harmonic generation (SHG) measurement reveals that KCdCO3F is a phase-matchable material for generation of doubled-frequency light at both 532 and 266 nm, with a large SHG response of approximately 5.2 times that of KH2PO4 (KDP) at 532 nm and a moderate SHG response of approximately 0.75 times that of β-BaB2O4 (BBO) at 266 nm. Therefore, it is a promising UV material for fourth harmonic generation on a 1064 nm Q-switched Nd:YAG laser. PMID:26488674

  4. Solution of the Inverse Spectroscopic Ellipsometry Problem for an Absorbing Substrate with a Dielectric Layer

    NASA Astrophysics Data System (ADS)

    Stas'kov, N. I.; Shulga, A. V.

    2016-03-01

    An analytical solution of the inverse spectroscopic ellipsometry problem for a transparent layer on an absorbing substrate is obtained based on the envelope function approximation. It is used to determine the spectral dependences of the refractive index n(λ) and absorption k(λ) for model and real silicon substrates with silicon dioxide layers. It was possible to determine analytically the effective optical characteristics of the silicon substrate in the approximation of a layer-substrate model with ideal interface boundaries. This result, together with the relative positions of the spectral curves for the ellipsometric angles tan ψ(λ) and cos Δ(λ) measured for a silicon substrate with a natural surface layer and for a silicon dioxide layer-silicon substrate structure, can be explained by the fact that the silicon dioxide layer is surrounded by transition and surface layers.

  5. Resonant dielectric metamaterials

    SciTech Connect

    Loui, Hung; Carroll, James; Clem, Paul G; Sinclair, Michael B

    2014-12-02

    A resonant dielectric metamaterial comprises a first and a second set of dielectric scattering particles (e.g., spheres) having different permittivities arranged in a cubic array. The array can be an ordered or randomized array of particles. The resonant dielectric metamaterials are low-loss 3D isotropic materials with negative permittivity and permeability. Such isotropic double negative materials offer polarization and direction independent electromagnetic wave propagation.

  6. Impact of Gd2O3 passivation layer on interfacial and electrical properties of atomic-layer-deposited ZrO2 gate dielectric on GaAs

    NASA Astrophysics Data System (ADS)

    Gong, Youpin; Zhai, Haifa; Liu, Xiaojie; Kong, Jizhou; Wu, Di; Li, Aidong

    2014-02-01

    ZrO2 gate dielectric films were fabricated on n-GaAs substrates by atomic layer deposition (ALD), using metal organic chemical vapor deposition (MOCVD)-derived ultrathin Gd2O3 film as interfacial control layer between ZrO2 and n-GaAs. The interfacial structure, capacitance-voltage and current-voltage properties of ZrO2/n-GaAs and ZrO2/Gd2O3/n-GaAs metal-oxide-semiconductor (MOS) capacitors have been investigated. The introduction of an ultrathin Gd2O3 control layer can effectively suppress the formation of As oxides and high valence Ga oxide at the high k/GaAs interface which evidently improved the electrical properties of GaAs-based MOS capacitors, such as higher accumulation capacitance and lower leakage current density. It was found that the current conduction mechanism of MOS capacitors varied from Poole-Frenkel emission to Schottky-Richardson emission after introducing the thin Gd2O3 layer. The band alignments of interfaces for ZrO2/GaAs and ZrO2/Gd2O3/GaAs were established, which indicates that the conduction band offset (CBO) for ZrO2/GaAs and ZrO2/Gd2O3/GaAs stacks are ˜1.45 and ˜1.62 eV, correspondingly.

  7. 3D microscope

    NASA Astrophysics Data System (ADS)

    Iizuka, Keigo

    2008-02-01

    In order to circumvent the fact that only one observer can view the image from a stereoscopic microscope, an attachment was devised for displaying the 3D microscopic image on a large LCD monitor for viewing by multiple observers in real time. The principle of operation, design, fabrication, and performance are presented, along with tolerance measurements relating to the properties of the cellophane half-wave plate used in the design.

  8. Synthesis and Evaluation of Self-Assembled Azido Monolayer as a Novel Dielectric Layer for Fabricating Pentacene-Based Organic Thin Film Transistors.

    PubMed

    Yeh, Je-Yuan; Tsai, Tzung-Da; Kuo, An Tsung; Chou, Ying-Shiun; Liou, Ying-Shian; Chang, Zhao-You; Tsiang, Raymond Chien-Chao; Guo, Tzung-Fang; Chang, Chien-Hsiang

    2015-05-01

    Self-assembled 3-azidopropyltriethoxysilane monolayer (SAM) is used as a dielectric layer to modify the interface between the silicon dioxide wafer and the pentacene semiconductor layer in an organic thin film transistor (OTFT), Au/pentacene/3-azidopropyltriethoxysilane/SiO2/Si. Compared to the commonly used alkyl siliane C18 dielectric, 3-azidopropyltriethoxysilane which possesses stable formal charges is far more effective in increasing the ON/OFF ratio of OTFT device with an improvement of nearly three orders of magnitude. Analysis and measurements reported in this paper have illustrated for the first time the improvement of OTFT performance by a SAM compound with stable formal charges. PMID:26504992

  9. Accurate characterization and understanding of interface trap density trends between atomic layer deposited dielectrics and AlGaN/GaN with bonding constraint theory

    SciTech Connect

    Ramanan, Narayanan; Lee, Bongmook; Misra, Veena

    2015-06-15

    Many dielectrics have been proposed for the gate stack or passivation of AlGaN/GaN based metal oxide semiconductor heterojunction field effect transistors, to reduce gate leakage and current collapse, both for power and RF applications. Atomic Layer Deposition (ALD) is preferred for dielectric deposition as it provides uniform, conformal, and high quality films with precise monolayer control of film thickness. Identification of the optimum ALD dielectric for the gate stack or passivation requires a critical investigation of traps created at the dielectric/AlGaN interface. In this work, a pulsed-IV traps characterization method has been used for accurate characterization of interface traps with a variety of ALD dielectrics. High-k dielectrics (HfO{sub 2}, HfAlO, and Al{sub 2}O{sub 3}) are found to host a high density of interface traps with AlGaN. In contrast, ALD SiO{sub 2} shows the lowest interface trap density (<2 × 10{sup 12 }cm{sup −2}) after annealing above 600 °C in N{sub 2} for 60 s. The trend in observed trap densities is subsequently explained with bonding constraint theory, which predicts a high density of interface traps due to a higher coordination state and bond strain in high-k dielectrics.

  10. Resistive and magnetoresistive properties of compacted CrO2 powders with different types of intergranular dielectric layers

    NASA Astrophysics Data System (ADS)

    Dalakova, N. V.; Belevtsev, B. I.; Beliayev, E. Yu.; Bludov, A. N.; Pashchenko, V. N.; Osmolovsky, M. G.; Osmolovskaya, O. M.

    2012-12-01

    Resistive, magnetoresistive and magnetic properties of four types of pressed CrO2 powders synthesized from chromic anhydride by the hydrothermal method were investigated. The new synthesis method allowed controlling the thickness of dielectric shells. The powders consisted of rounded particles (≈120 nm in dia.) or acicular crystals (≈22.9 nm in dia. and 302 nm in length). The particles were covered with a surface dielectric shell of different thickness and type (e.g. β-CrOOH oxyhydroxide or chromium oxide Cr2O3). The influence of the properties and the thickness of intergranular dielectric layers as well as the shape of CrO2 particles on the tunneling resistance and magnetoresistance (MR) of the pressed powders was studied. It was found that at low temperatures all the investigated samples displayed a nonmetallic temperature dependence of resistance and a giant negative MR. The maximal values of MR at T ≈ 5 K were found to be approx. 37% in relatively low magnetic fields (0.5 T). The MR decreased rapidly with increasing temperature (down to approx. 1% in 1 T at T ≈ 200 K). At low temperatures the powders with acicular particles exhibited a new type of MR hysteresis and nonmonotonous dependence of MR with increasing magnetic field. A nonmonotonous temperature dependence Hp(T), where Hp is the field in which the resistance is maximal, mismatch between the values of Hp and coercive force Hc, and the anisotropy of MR as a function of mutual orientation of transport current and magnetic field were observed.

  11. A novel injectable thermoresponsive and cytocompatible gel of poly(N-isopropylacrylamide) with layered double hydroxides facilitates siRNA delivery into chondrocytes in 3D culture.

    PubMed

    Yang, Hsiao-yin; van Ee, Renz J; Timmer, Klaas; Craenmehr, Eric G M; Huang, Julie H; Öner, F Cumhur; Dhert, Wouter J A; Kragten, Angela H M; Willems, Nicole; Grinwis, Guy C M; Tryfonidou, Marianna A; Papen-Botterhuis, Nicole E; Creemers, Laura B

    2015-09-01

    Hybrid hydrogels composed of poly(N-isopropylacrylamide) (pNIPAAM) and layered double hydroxides (LDHs) are presented in this study as novel injectable and thermoresponsive materials for siRNA delivery, which could specifically target several negative regulators of tissue homeostasis in cartilaginous tissues. Effectiveness of siRNA transfection using pNIPAAM formulated with either MgAl-LDH or MgFe-LDH platelets was investigated using osteoarthritic chondrocytes. Glyceraldehyde-3-phosphate dehydrogenase (GAPDH) was used as an endogenous model gene to evaluate the extent of silencing. No significant adverse effects of pNIPAAM/LDH hydrogels on cell viability were noticed. Cellular uptake of fluorescently labeled siRNA was greatly enhanced (>75%) in pNIPAAM/LDH hydrogel constructs compared to alginate, hyaluronan and fibrin gels, and was absent in pNIPAAM hydrogel without LDH platelets. When using siRNA against GAPDH, 82-98% reduction of gene expression was found in both types of pNIPAAM/LDH hydrogel constructs after 6 days of culturing. In the pNIPAAM/MgAl-LDH hybrid hydrogel, 80-95% of GAPDH enzyme activity was reduced in parallel with gene. Our findings show that the combination of a cytocompatible hydrogel and therapeutic RNA oligonucleotides is feasible. Thus it might hold promise in treating degeneration of cartilaginous tissues by providing supporting scaffolds for cells and interference with locally produced degenerative factors. PMID:26022968

  12. Estimation of water distribution and degradation mechanisms in polymer electrolyte membrane fuel cell gas diffusion layers using a 3D Monte Carlo model

    NASA Astrophysics Data System (ADS)

    Seidenberger, K.; Wilhelm, F.; Schmitt, T.; Lehnert, W.; Scholta, J.

    Understanding of both water management in PEM fuel cells and degradation mechanisms of the gas diffusion layer (GDL) and their mutual impact is still at least incomplete. Different modelling approaches contribute to gain deeper insight into the processes occurring during fuel cell operation. Considering the GDL, the models can help to obtain information about the distribution of liquid water within the material. Especially, flooded regions can be identified, and the water distribution can be linked to the system geometry. Employed for material development, this information can help to increase the life time of the GDL as a fuel cell component and the fuel cell as the entire system. The Monte Carlo (MC) model presented here helps to simulate and analyse the water household in PEM fuel cell GDLs. This model comprises a three-dimensional, voxel-based representation of the GDL substrate, a section of the flowfield channel and the corresponding rib. Information on the water distribution within the substrate part of the GDL can be estimated.

  13. 3D Printing for Tissue Engineering

    PubMed Central

    Jia, Jia; Yao, Hai; Mei, Ying

    2016-01-01

    Tissue engineering aims to fabricate functional tissue for applications in regenerative medicine and drug testing. More recently, 3D printing has shown great promise in tissue fabrication with a structural control from micro- to macro-scale by using a layer-by-layer approach. Whether through scaffold-based or scaffold-free approaches, the standard for 3D printed tissue engineering constructs is to provide a biomimetic structural environment that facilitates tissue formation and promotes host tissue integration (e.g., cellular infiltration, vascularization, and active remodeling). This review will cover several approaches that have advanced the field of 3D printing through novel fabrication methods of tissue engineering constructs. It will also discuss the applications of synthetic and natural materials for 3D printing facilitated tissue fabrication. PMID:26869728

  14. Metal-Oxide-Semiconductor Interface and Dielectric Properties of Atomic Layer Deposited SiO2 on GaN

    NASA Astrophysics Data System (ADS)

    Takashima, Shinya; Li, Zhongda; Chow, T. Paul

    2013-08-01

    The dielectric and MOS interface properties of SiO2 deposited with atomic layer deposition (ALD) on GaN with different surface treatments have been investigated with DC current-voltage (I-V) measurements and UV-assisted capacitance-voltage (C-V) measurements. Dielectric breakdown characteristics and leakage conduction mechanism for ALD SiO2 depend on surface conditions. Dry etch with NaOH post-etch GaN surface exhibited high oxide breakdown voltage with small distribution, larger barrier height characteristics, and higher charge to breakdown characteristics when compared with un-etched surface condition and dry etch with tetramethylammonium hydroxide (TMAH) post-etch surface condition. Moreover, fixed charge density and interface trap density at MOS interface extracted by UV-assisted C-V were comparable between un-etched surface sample and dry etch with NaOH post-etch surface sample, indicating dry etching damage recovery and demonstrating the usability of NaOH post-etching treatment. Comparison has also been made to a composite oxide of SiO2/Al2O3/SiO2, showing possibility of oxide charge engineering toward positive threshold voltage but carrier trapping by insertion of Al2O3.

  15. Dielectric Genome of van der Waals Heterostructures.

    PubMed

    Andersen, Kirsten; Latini, Simone; Thygesen, Kristian S

    2015-07-01

    Vertical stacking of two-dimensional (2D) crystals, such as graphene and hexagonal boron nitride, has recently lead to a new class of materials known as van der Waals heterostructures (vdWHs) with unique and highly tunable electronic properties. Ab initio calculations should in principle provide a powerful tool for modeling and guiding the design of vdWHs, but in their traditional form such calculations are only feasible for commensurable structures with a few layers. Here we show that the dielectric properties of realistic, incommensurable vdWHs comprising hundreds of layers can be efficiently calculated using a multiscale approach where the dielectric functions of the individual layers (the dielectric building blocks) are computed ab initio and coupled together via the long-range Coulomb interaction. We use the method to illustrate the 2D-3D transition of the dielectric function of multilayer MoS2 crystals, the hybridization of quantum plasmons in thick graphene/hBN heterostructures, and to demonstrate the intricate effect of substrate screening on the non-Rydberg exciton series in supported WS2. The dielectric building blocks for a variety of 2D crystals are available in an open database together with the software for solving the coupled electrodynamic equations. PMID:26047386

  16. Zn-Al layered double hydroxide prepared at different molar ratios: Preparation, characterization, optical and dielectric properties

    SciTech Connect

    Ahmed, Abdullah Ahmed Ali; Talib, Zainal Abidin; Zobir bin Hussein, Mohd; Zakaria, Azmi

    2012-07-15

    The co-precipitation method was used to prepare Zn-Al-NO{sub 3}-LDH at different Zn{sup 2+}/Al{sup 3+} molar ratios (2, 3, 4, 5 and 6) and pH value of 7.5. The structure, textural, composition and morphological properties were investigated using powder X-ray diffraction (PXRD), thermogravimetric analysis (TGA), Fourier transform infrared (FT-IR) and scanning electron microscope (SEM), respectively. The crystallinity of LDH samples were found to improve as molar ratio decreased which is attributed to the distortion of the hydroxide layers networks of the LDH crystal by the larger difference in ionic radii of Zn{sup 2+} and Al{sup 3+}. The optical band gap energy of LDH samples were evaluated using absorbance data from UV-Vis-NIR Diffuse reflectance spectroscopy. Band gaps were affected by the variation of the Zn{sup 2+}/Al{sup 3+} molar ratio is due to the formation of the low crystalline phases (ZnO and ZnAl{sub 2}O{sub 4}). The water molecules and anionic NO{sub 3}{sup -} in the LDH interlayer were responsible for the generation of the dielectric response. This response can be described by an anomalous low frequency dispersion using the second type of Universal Power Law. The dominance of ZnO dipoles and charge carriers (NO{sub 3}{sup -} ions) in the dielectric relaxation increases with the increasing molar ratio. - Graphical abstract: (a) Schematic diagram of Zn-Al- NO{sub 3}-LDH shows the LDH structure, (b) Kubelka-Munk transformed reflectance spectra and c. The dielectric constant versus frequency of Zn-Al- NO{sub 3}-LDH samples. Highlights: Black-Right-Pointing-Pointer Zn-Al-NO{sub 3}-LDH was prepared at different Zn{sup 2+}/Al{sup 3+} molar ratios (2, 3, 4, 5 and 6). Black-Right-Pointing-Pointer The crystallinity of LDH phase decreased with increase of Zn{sup 2+}/Al{sup 3+} molar ratio. Black-Right-Pointing-Pointer The optical band gaps of LDH samples have been measured. Black-Right-Pointing-Pointer Dielectric response of LDH can be described by anomalous low

  17. Multiviewer 3D monitor

    NASA Astrophysics Data System (ADS)

    Kostrzewski, Andrew A.; Aye, Tin M.; Kim, Dai Hyun; Esterkin, Vladimir; Savant, Gajendra D.

    1998-09-01

    Physical Optics Corporation has developed an advanced 3-D virtual reality system for use with simulation tools for training technical and military personnel. This system avoids such drawbacks of other virtual reality (VR) systems as eye fatigue, headaches, and alignment for each viewer, all of which are due to the need to wear special VR goggles. The new system is based on direct viewing of an interactive environment. This innovative holographic multiplexed screen technology makes it unnecessary for the viewer to wear special goggles.

  18. 3D Audio System

    NASA Technical Reports Server (NTRS)

    1992-01-01

    Ames Research Center research into virtual reality led to the development of the Convolvotron, a high speed digital audio processing system that delivers three-dimensional sound over headphones. It consists of a two-card set designed for use with a personal computer. The Convolvotron's primary application is presentation of 3D audio signals over headphones. Four independent sound sources are filtered with large time-varying filters that compensate for motion. The perceived location of the sound remains constant. Possible applications are in air traffic control towers or airplane cockpits, hearing and perception research and virtual reality development.

  19. Competition between the bulk and the dissociation layer in electrohydrodynamic flow of dielectric liquid around coplanar electrodes.

    PubMed

    Suh, Y K; Baek, K H

    2013-02-01

    An experimental and numerical study has been conducted on the electrohydrodynamic flow around coplanar electrodes with a dielectric liquid: dodecane mixed with the surfactant Span 80. It is shown that the flow is asymmetric, although the electrode is symmetrically arranged, and numerically, we have shown that a difference in the ionic size can reproduce such asymmetric patterns. It is also found that the dissociation layer effect becomes more important in determining the flow pattern than is predicted from the conventional theory where the Langevin formula is used for the recombination constant. In numerical simulations, reducing the recombination constant to 0.035-0.055 times the Langevin value turned out to produce good comparisons between the experimental and the numerical results for the electrode pairs with 1 and 0.2 mm gaps. PMID:23496612

  20. Vacuum ultraviolet photochemical selective area atomic layer deposition of Al{sub 2}O{sub 3} dielectrics

    SciTech Connect

    Chalker, P. R. Marshall, P. A.; Dawson, K.; Brunell, I. F.; Sutcliffe, C. J.; Potter, R. J.

    2015-01-15

    We report the photochemical atomic layer deposition of Al{sub 2}O{sub 3} thin films and the use of this process to achieve area-selective film deposition. A shuttered vacuum ultraviolet (VUV) light source is used to excite molecular oxygen and trimethyl aluminum to deposit films at 60°C. In-situ QCM and post-deposition ellipsometric measurements both show that the deposition rate is saturative as a function of irradiation time. Selective area deposition was achieved by projecting the VUV light through a metalized magnesium fluoride photolithographic mask and the selectivity of deposition on the illuminated and masked regions of the substrate is a logarithmic function of the UV exposure time. The Al{sub 2}O{sub 3} films exhibit dielectric constants of 8 – 10 at 1 MHz after forming gas annealing, similar to films deposited by conventional thermal ALD.

  1. Analysis of a static undulation on the surface of a thin dielectric liquid layer formed by dielectrophoresis forces

    NASA Astrophysics Data System (ADS)

    Brown, Carl V.; McHale, Glen; Mottram, Nigel J.

    2011-07-01

    A layer of insulating liquid of dielectric constant ɛOil and average thickness h- coats a flat surface at y = 0 at which a one-dimensional sinusoidal potential V(x ,0)=VOcos(πx /p) is applied. Dielectrophoresis forces create a static undulation (or "wrinkle") distortion h(x) of period p at the liquid/air interface. Analytical expressions have been derived for the electrostatic energy and the interfacial energy associated with the surface undulation when h(x)=h--(1/2)Acos(2πx /p) yielding a scaling relationship for A as a function of h-, p, VO, ɛOil and the surface tension. The analysis is valid as A/p → 0, and in this limit convergence with numerical simulation of the system is shown.

  2. Contact-free sheet resistance determination of large area graphene layers by an open dielectric loaded microwave cavity

    SciTech Connect

    Shaforost, O.; Wang, K.; Adabi, M.; Guo, Z.; Hanham, S.; Klein, N.; Goniszewski, S.; Gallop, J.; Hao, L.

    2015-01-14

    A method for contact-free determination of the sheet resistance of large-area and arbitrary shaped wafers or sheets coated with graphene and other (semi) conducting ultrathin layers is described, which is based on an open dielectric loaded microwave cavity. The sample under test is exposed to the evanescent resonant field outside the cavity. A comparison with a closed cavity configuration revealed that radiation losses have no significant influence of the experimental results. Moreover, the microwave sheet resistance results show good agreement with the dc conductivity determined by four-probe van der Pauw measurements on a set of CVD samples transferred on quartz. As an example of a practical application, correlations between the sheet resistance and deposition conditions for CVD graphene transferred on quartz wafers are described. Our method has a high potential as measurement standard for contact-free sheet resistance measurement and mapping of large area graphene samples.

  3. Contact-free sheet resistance determination of large area graphene layers by an open dielectric loaded microwave cavity

    NASA Astrophysics Data System (ADS)

    Shaforost, O.; Wang, K.; Goniszewski, S.; Adabi, M.; Guo, Z.; Hanham, S.; Gallop, J.; Hao, L.; Klein, N.

    2015-01-01

    A method for contact-free determination of the sheet resistance of large-area and arbitrary shaped wafers or sheets coated with graphene and other (semi) conducting ultrathin layers is described, which is based on an open dielectric loaded microwave cavity. The sample under test is exposed to the evanescent resonant field outside the cavity. A comparison with a closed cavity configuration revealed that radiation losses have no significant influence of the experimental results. Moreover, the microwave sheet resistance results show good agreement with the dc conductivity determined by four-probe van der Pauw measurements on a set of CVD samples transferred on quartz. As an example of a practical application, correlations between the sheet resistance and deposition conditions for CVD graphene transferred on quartz wafers are described. Our method has a high potential as measurement standard for contact-free sheet resistance measurement and mapping of large area graphene samples.

  4. Compound surface-plasmon-polariton waves guided by a thin metal layer sandwiched between a homogeneous isotropic dielectric material and a structurally chiral material

    NASA Astrophysics Data System (ADS)

    Chiadini, Francesco; Fiumara, Vincenzo; Scaglione, Antonio; Lakhtakia, Akhlesh

    2016-03-01

    Multiple compound surface plasmon-polariton (SPP) waves can be guided by a structure consisting of a sufficiently thick layer of metal sandwiched between a homogeneous isotropic dielectric (HID) material and a dielectric structurally chiral material (SCM). The compound SPP waves are strongly bound to both metal/dielectric interfaces when the thickness of the metal layer is comparable to the skin depth but just to one of the two interfaces when the thickness is much larger. The compound SPP waves differ in phase speed, attenuation rate, and field profile, even though all are excitable at the same frequency. Some compound SPP waves are not greatly affected by the choice of the direction of propagation in the transverse plane but others are, depending on metal thickness. For fixed metal thickness, the number of compound SPP waves depends on the relative permittivity of the HID material, which can be useful for sensing applications.

  5. The effects of Bi4Ti3O12 interfacial ferroelectric layer on the dielectric properties of Au/n-Si structures

    NASA Astrophysics Data System (ADS)

    Gökçen, Muharrem; Yıldırım, Mert

    2015-06-01

    Au/n-Si metal-semiconductor (MS) and Au/Bi4Ti3O12/n-Si metal-ferroelectric-semiconductor (MFS) structures were fabricated and admittance measurements were held between 5 kHz and 1 MHz at room temperature so that dielectric properties of these structures could be investigated. The ferroelectric interfacial layer Bi4Ti3O12 decreased the polarization voltage by providing permanent dipoles at metal/semiconductor interface. Depending on different mechanisms, dispersion behavior was observed in dielectric constant, dielectric loss and loss tangent versus bias voltage plots of both MS and MFS structures. The real and imaginary parts of complex modulus of MFS structure take smaller values than those of MS structure, because permanent dipoles in ferroelectric layer cause a large spontaneous polarization mechanism. While the dispersion in AC conductivity versus frequency plots of MS structure was observed at high frequencies, for MFS structure it was observed at lower frequencies.

  6. Two-layered disc quasi-optical dielectric resonators: electrodynamics and application perspectives for complex permittivity measurements of lossy liquids

    NASA Astrophysics Data System (ADS)

    Barannik, A. A.; Cherpak, N. T.; Prokopenko, Yu V.; Filipov, Yu F.; Shaforost, E. N.; Shipilova, I. A.

    2007-07-01

    Electromagnetic properties of novel quasi-optical resonators are studied theoretically and experimentally. The resonators are a radially two-layered dielectric disc sandwiched between conducting endplates. The internal layer can be filled with air or lossy liquid. Whispering gallery modes are excited in such a resonator and the mode energy is concentrated near the inner side of the cylindrical surface of an external layer. The measurement data obtained in the Ka-band are compared with theoretical calculations of eigenfrequencies and quality factors of the Teflon resonator filled with water, ethyl alcohol, benzene and aqueous solutions of ethyl alcohol. A number of 'anomalous' properties of the resonator can be described using Maxwell equations. The experimental data on the complex permittivity of a binary mixture water-ethyl alcohol are compared with the values calculated in terms of Debye's function. An important feature of the proposed technique is that it holds promise for making first principle microwave measurements of the permittivity of lossy liquids.

  7. 3D Surgical Simulation

    PubMed Central

    Cevidanes, Lucia; Tucker, Scott; Styner, Martin; Kim, Hyungmin; Chapuis, Jonas; Reyes, Mauricio; Proffit, William; Turvey, Timothy; Jaskolka, Michael

    2009-01-01

    This paper discusses the development of methods for computer-aided jaw surgery. Computer-aided jaw surgery allows us to incorporate the high level of precision necessary for transferring virtual plans into the operating room. We also present a complete computer-aided surgery (CAS) system developed in close collaboration with surgeons. Surgery planning and simulation include construction of 3D surface models from Cone-beam CT (CBCT), dynamic cephalometry, semi-automatic mirroring, interactive cutting of bone and bony segment repositioning. A virtual setup can be used to manufacture positioning splints for intra-operative guidance. The system provides further intra-operative assistance with the help of a computer display showing jaw positions and 3D positioning guides updated in real-time during the surgical procedure. The CAS system aids in dealing with complex cases with benefits for the patient, with surgical practice, and for orthodontic finishing. Advanced software tools for diagnosis and treatment planning allow preparation of detailed operative plans, osteotomy repositioning, bone reconstructions, surgical resident training and assessing the difficulties of the surgical procedures prior to the surgery. CAS has the potential to make the elaboration of the surgical plan a more flexible process, increase the level of detail and accuracy of the plan, yield higher operative precision and control, and enhance documentation of cases. Supported by NIDCR DE017727, and DE018962 PMID:20816308

  8. Zirconium doped TiO2 thin films: A promising dielectric layer

    NASA Astrophysics Data System (ADS)

    Kumar, Arvind; Mondal, Sandip; Rao, K. S. R. Koteswara

    2016-05-01

    In the present work, we have fabricated the zirconium doped TiO2 thin (ZTO) films from a facile spin - coating method. The addition of Zirconium in TiO2 offers conduction band offset to Si and consequently decreased the leakage current density by approximately two orders as compared to pure TiO2 thin (TO) films. The ZTO thin film shows a high dielectric constant 27 with a very low leakage current density ˜10-8 A/cm2. The oxide capacitate, flat band voltage and change in flat band voltage are 172 pF, -1.19 V and 54 mV. The AFM analysis confirmed the compact and pore free flat surface. The RMS surface roughness is found to be 1.5 Å. The ellipsometry analysis also verified the fact with a high refractive index 2.21.

  9. Recent developments in DFD (depth-fused 3D) display and arc 3D display

    NASA Astrophysics Data System (ADS)

    Suyama, Shiro; Yamamoto, Hirotsugu

    2015-05-01

    We will report our recent developments in DFD (Depth-fused 3D) display and arc 3D display, both of which have smooth movement parallax. Firstly, fatigueless DFD display, composed of only two layered displays with a gap, has continuous perceived depth by changing luminance ratio between two images. Two new methods, called "Edge-based DFD display" and "Deep DFD display", have been proposed in order to solve two severe problems of viewing angle and perceived depth limitations. Edge-based DFD display, layered by original 2D image and its edge part with a gap, can expand the DFD viewing angle limitation both in 2D and 3D perception. Deep DFD display can enlarge the DFD image depth by modulating spatial frequencies of front and rear images. Secondly, Arc 3D display can provide floating 3D images behind or in front of the display by illuminating many arc-shaped directional scattering sources, for example, arcshaped scratches on a flat board. Curved Arc 3D display, composed of many directional scattering sources on a curved surface, can provide a peculiar 3D image, for example, a floating image in the cylindrical bottle. The new active device has been proposed for switching arc 3D images by using the tips of dual-frequency liquid-crystal prisms as directional scattering sources. Directional scattering can be switched on/off by changing liquid-crystal refractive index, resulting in switching of arc 3D image.

  10. Magmatic Systems in 3-D

    NASA Astrophysics Data System (ADS)

    Kent, G. M.; Harding, A. J.; Babcock, J. M.; Orcutt, J. A.; Bazin, S.; Singh, S.; Detrick, R. S.; Canales, J. P.; Carbotte, S. M.; Diebold, J.

    2002-12-01

    Multichannel seismic (MCS) images of crustal magma chambers are ideal targets for advanced visualization techniques. In the mid-ocean ridge environment, reflections originating at the melt-lens are well separated from other reflection boundaries, such as the seafloor, layer 2A and Moho, which enables the effective use of transparency filters. 3-D visualization of seismic reflectivity falls into two broad categories: volume and surface rendering. Volumetric-based visualization is an extremely powerful approach for the rapid exploration of very dense 3-D datasets. These 3-D datasets are divided into volume elements or voxels, which are individually color coded depending on the assigned datum value; the user can define an opacity filter to reject plotting certain voxels. This transparency allows the user to peer into the data volume, enabling an easy identification of patterns or relationships that might have geologic merit. Multiple image volumes can be co-registered to look at correlations between two different data types (e.g., amplitude variation with offsets studies), in a manner analogous to draping attributes onto a surface. In contrast, surface visualization of seismic reflectivity usually involves producing "fence" diagrams of 2-D seismic profiles that are complemented with seafloor topography, along with point class data, draped lines and vectors (e.g. fault scarps, earthquake locations and plate-motions). The overlying seafloor can be made partially transparent or see-through, enabling 3-D correlations between seafloor structure and seismic reflectivity. Exploration of 3-D datasets requires additional thought when constructing and manipulating these complex objects. As numbers of visual objects grow in a particular scene, there is a tendency to mask overlapping objects; this clutter can be managed through the effective use of total or partial transparency (i.e., alpha-channel). In this way, the co-variation between different datasets can be investigated

  11. Thermally-induced single-crystal-to-single-crystal transformations from a 2D two-fold interpenetrating square lattice layer to a 3D four-fold interpenetrating diamond framework and its application in dye-sensitized solar cells.

    PubMed

    Gao, Song; Fan, Rui Qing; Wang, Xin Ming; Wei, Li Guo; Song, Yang; Du, Xi; Xing, Kai; Wang, Ping; Yang, Yu Lin

    2016-07-28

    In this work, a rare 2D → 3D single-crystal-to-single-crystal transformation (SCSC) is observed in metal-organic coordination complexes, which is triggered by thermal treatment. The 2D two-fold interpenetrating square lattice layer [Cd(IBA)2]n (1) is irreversibly converted into a 3D four-fold interpenetrating diamond framework {[Cd(IBA)2(H2O)]·2.5H2O}n (2) (HIBA = 4-(1H-imidazol-1-yl)benzoic acid). Consideration is given to these two complexes with different interpenetrating structures and dimensionality, and their influence on photovoltaic properties are studied. Encouraged by the UV-visible absorption and HOMO-LUMO energy states matched for sensitizing TiO2, the two complexes are employed in combination with N719 in dye-sensitized solar cells (DSSCs) to compensate absorption in the ultraviolet and blue-violet region, offset competitive visible light absorption of I3(-) and reducing charge the recombination of injected electrons. After co-sensitization with 1 and 2, the device co-sensitized by 1/N719 and 2/N719 to yield overall efficiencies of 7.82% and 8.39%, which are 19.94% and 28.68% higher than that of the device sensitized only by N719 (6.52%). Consequently, high dimensional interpenetrating complexes could serve as excellent co-sensitizers and have application in DSSCs. PMID:27356177

  12. Surface participation and dielectric loss in superconducting qubits

    SciTech Connect

    Wang, C.; Axline, C.; Gao, Y. Y.; Brecht, T.; Chu, Y.; Frunzio, L.; Devoret, M. H.; Schoelkopf, R. J.

    2015-10-19

    We study the energy relaxation times (T{sub 1}) of superconducting transmon qubits in 3D cavities as a function of dielectric participation ratios of material surfaces. This surface participation ratio, representing the fraction of electric field energy stored in a dissipative surface layer, is computed by a two-step finite-element simulation and experimentally varied by qubit geometry. With a clean electromagnetic environment and suppressed non-equilibrium quasiparticle density, we find an approximately proportional relation between the transmon relaxation rates and surface participation ratios. These results suggest dielectric dissipation arising from material interfaces is the major limiting factor for the T{sub 1} of transmons in 3D circuit quantum electrodynamics architecture. Our analysis also supports the notion of spatial discreteness of surface dielectric dissipation.

  13. Effect of gold subsurface layer on the surface activity and segregation in Pt/Au/Pt3M (where M = 3d transition metals) alloy catalyst from first-principles

    NASA Astrophysics Data System (ADS)

    Kim, Chang-Eun; Lim, Dong-Hee; Jang, Jong Hyun; Kim, Hyoung Juhn; Yoon, Sung Pil; Han, Jonghee; Nam, Suk Woo; Hong, Seong-Ahn; Soon, Aloysius; Ham, Hyung Chul

    2015-01-01

    The effect of a subsurface hetero layer (thin gold) on the activity and stability of Pt skin surface in Pt3M system (M = 3d transition metals) is investigated using the spin-polarized density functional theory calculation. First, we find that the heterometallic interaction between the Pt skin surface and the gold subsurface in Pt/Au/Pt3M system can significantly modify the electronic structure of the Pt skin surface. In particular, the local density of states projected onto the d states of Pt skin surface near the Fermi level is drastically decreased compared to the Pt/Pt/Pt3M case, leading to the reduction of the oxygen binding strength of the Pt skin surface. This modification is related to the increase of surface charge polarization of outmost Pt skin atoms by the electron transfer from the gold subsurface atoms. Furthermore, a subsurface gold layer is found to cast the energetic barrier to the segregation loss of metal atoms from the bulk (inside) region, which can enhance the durability of Pt3M based catalytic system in oxygen reduction condition at fuel cell devices. This study highlights that a gold subsurface hetero layer can provide an additional mean to tune the surface activity toward oxygen species and in turn the oxygen reduction reaction, where the utilization of geometric strain already reaches its practical limit.

  14. Effect of gold subsurface layer on the surface activity and segregation in Pt/Au/Pt3M (where M = 3d transition metals) alloy catalyst from first-principles.

    PubMed

    Kim, Chang-Eun; Lim, Dong-Hee; Jang, Jong Hyun; Kim, Hyoung Juhn; Yoon, Sung Pil; Han, Jonghee; Nam, Suk Woo; Hong, Seong-Ahn; Soon, Aloysius; Ham, Hyung Chul

    2015-01-21

    The effect of a subsurface hetero layer (thin gold) on the activity and stability of Pt skin surface in Pt3M system (M = 3d transition metals) is investigated using the spin-polarized density functional theory calculation. First, we find that the heterometallic interaction between the Pt skin surface and the gold subsurface in Pt/Au/Pt3M system can significantly modify the electronic structure of the Pt skin surface. In particular, the local density of states projected onto the d states of Pt skin surface near the Fermi level is drastically decreased compared to the Pt/Pt/Pt3M case, leading to the reduction of the oxygen binding strength of the Pt skin surface. This modification is related to the increase of surface charge polarization of outmost Pt skin atoms by the electron transfer from the gold subsurface atoms. Furthermore, a subsurface gold layer is found to cast the energetic barrier to the segregation loss of metal atoms from the bulk (inside) region, which can enhance the durability of Pt3M based catalytic system in oxygen reduction condition at fuel cell devices. This study highlights that a gold subsurface hetero layer can provide an additional mean to tune the surface activity toward oxygen species and in turn the oxygen reduction reaction, where the utilization of geometric strain already reaches its practical limit. PMID:25612725

  15. Effect of gold subsurface layer on the surface activity and segregation in Pt/Au/Pt{sub 3}M (where M = 3d transition metals) alloy catalyst from first-principles

    SciTech Connect

    Kim, Chang-Eun; Lim, Dong-Hee; Jang, Jong Hyun; Kim, Hyoung Juhn; Yoon, Sung Pil; Han, Jonghee; Nam, Suk Woo; Hong, Seong-Ahn; Soon, Aloysius E-mail: hchahm@kist.re.kr; Ham, Hyung Chul E-mail: hchahm@kist.re.kr

    2015-01-21

    The effect of a subsurface hetero layer (thin gold) on the activity and stability of Pt skin surface in Pt{sub 3}M system (M = 3d transition metals) is investigated using the spin-polarized density functional theory calculation. First, we find that the heterometallic interaction between the Pt skin surface and the gold subsurface in Pt/Au/Pt{sub 3}M system can significantly modify the electronic structure of the Pt skin surface. In particular, the local density of states projected onto the d states of Pt skin surface near the Fermi level is drastically decreased compared to the Pt/Pt/Pt{sub 3}M case, leading to the reduction of the oxygen binding strength of the Pt skin surface. This modification is related to the increase of surface charge polarization of outmost Pt skin atoms by the electron transfer from the gold subsurface atoms. Furthermore, a subsurface gold layer is found to cast the energetic barrier to the segregation loss of metal atoms from the bulk (inside) region, which can enhance the durability of Pt{sub 3}M based catalytic system in oxygen reduction condition at fuel cell devices. This study highlights that a gold subsurface hetero layer can provide an additional mean to tune the surface activity toward oxygen species and in turn the oxygen reduction reaction, where the utilization of geometric strain already reaches its practical limit.

  16. Some solutions of the 3D Laplace equation in a layer with oscillating boundary describing an array of nanotubes and an application to cold field emission. I. Regular array

    NASA Astrophysics Data System (ADS)

    Brüning, J.; Dobrokhotov, S. Yu.; Minenkov, D. S.

    2011-12-01

    The aim of this paper is to construct solutions of the Dirichlet problem for the 3D Laplace equation in a layer with highly oscillating boundary. The boundary simulates the surface of a nanotube array, and the solutions are applied to compute the cold field electron emission. We suggest a family of exact solutions that solve the problem for a boundary with appropriate geometry. These solutions, along with the Fowler-Nordheim formula, allow one to present explicit asymptotic formulas for the electric field and the emission current. In this part of the paper, we consider the main mathematical aspects, restricting ourselves to the analysis of properties of the potential created by a single tube and a regular array of tubes. In the next part, we shall consider some cases corresponding to nonregular arrays of tubes and concrete physical examples.

  17. 3D acoustic atmospheric tomography

    NASA Astrophysics Data System (ADS)

    Rogers, Kevin; Finn, Anthony

    2014-10-01

    This paper presents a method for tomographically reconstructing spatially varying 3D atmospheric temperature profiles and wind velocity fields based. Measurements of the acoustic signature measured onboard a small Unmanned Aerial Vehicle (UAV) are compared to ground-based observations of the same signals. The frequency-shifted signal variations are then used to estimate the acoustic propagation delay between the UAV and the ground microphones, which are also affected by atmospheric temperature and wind speed vectors along each sound ray path. The wind and temperature profiles are modelled as the weighted sum of Radial Basis Functions (RBFs), which also allow local meteorological measurements made at the UAV and ground receivers to supplement any acoustic observations. Tomography is used to provide a full 3D reconstruction/visualisation of the observed atmosphere. The technique offers observational mobility under direct user control and the capacity to monitor hazardous atmospheric environments, otherwise not justifiable on the basis of cost or risk. This paper summarises the tomographic technique and reports on the results of simulations and initial field trials. The technique has practical applications for atmospheric research, sound propagation studies, boundary layer meteorology, air pollution measurements, analysis of wind shear, and wind farm surveys.

  18. Cast dielectric composite linear accelerator

    DOEpatents

    Sanders, David M.; Sampayan, Stephen; Slenes, Kirk; Stoller, H. M.

    2009-11-10

    A linear accelerator having cast dielectric composite layers integrally formed with conductor electrodes in a solventless fabrication process, with the cast dielectric composite preferably having a nanoparticle filler in an organic polymer such as a thermosetting resin. By incorporating this cast dielectric composite the dielectric constant of critical insulating layers of the transmission lines of the accelerator are increased while simultaneously maintaining high dielectric strengths for the accelerator.

  19. 3D polarimetric purity

    NASA Astrophysics Data System (ADS)

    Gil, José J.; San José, Ignacio

    2010-11-01

    From our previous definition of the indices of polarimetric purity for 3D light beams [J.J. Gil, J.M. Correas, P.A. Melero and C. Ferreira, Monogr. Semin. Mat. G. de Galdeano 31, 161 (2004)], an analysis of their geometric and physical interpretation is presented. It is found that, in agreement with previous results, the first parameter is a measure of the degree of polarization, whereas the second parameter (called the degree of directionality) is a measure of the mean angular aperture of the direction of propagation of the corresponding light beam. This pair of invariant, non-dimensional, indices of polarimetric purity contains complete information about the polarimetric purity of a light beam. The overall degree of polarimetric purity is obtained as a weighted quadratic average of the degree of polarization and the degree of directionality.

  20. 3D field harmonics

    SciTech Connect

    Caspi, S.; Helm, M.; Laslett, L.J.

    1991-03-30

    We have developed an harmonic representation for the three dimensional field components within the windings of accelerator magnets. The form by which the field is presented is suitable for interfacing with other codes that make use of the 3D field components (particle tracking and stability). The field components can be calculated with high precision and reduced cup time at any location (r,{theta},z) inside the magnet bore. The same conductor geometry which is used to simulate line currents is also used in CAD with modifications more readily available. It is our hope that the format used here for magnetic fields can be used not only as a means of delivering fields but also as a way by which beam dynamics can suggest correction to the conductor geometry. 5 refs., 70 figs.

  1. 'Bonneville' in 3-D!

    NASA Technical Reports Server (NTRS)

    2004-01-01

    The Mars Exploration Rover Spirit took this 3-D navigation camera mosaic of the crater called 'Bonneville' after driving approximately 13 meters (42.7 feet) to get a better vantage point. Spirit's current position is close enough to the edge to see the interior of the crater, but high enough and far enough back to get a view of all of the walls. Because scientists and rover controllers are so pleased with this location, they will stay here for at least two more martian days, or sols, to take high resolution panoramic camera images of 'Bonneville' in its entirety. Just above the far crater rim, on the left side, is the rover's heatshield, which is visible as a tiny reflective speck.

  2. Cryogenic 3D printing for tissue engineering.

    PubMed

    Adamkiewicz, Michal; Rubinsky, Boris

    2015-12-01

    We describe a new cryogenic 3D printing technology for freezing hydrogels, with a potential impact to tissue engineering. We show that complex frozen hydrogel structures can be generated when the 3D object is printed immersed in a liquid coolant (liquid nitrogen), whose upper surface is maintained at the same level as the highest deposited layer of the object. This novel approach ensures that the process of freezing is controlled precisely, and that already printed frozen layers remain at a constant temperature. We describe the device and present results which illustrate the potential of the new technology. PMID:26548335

  3. Floating electrode electrowetting on hydrophobic dielectric with an SiO2 layer

    NASA Astrophysics Data System (ADS)

    Khodayari, Mehdi; Hahne, Benjamin; Crane, Nathan B.; Volinsky, Alex A.

    2013-05-01

    Floating electrode electrowetting is caused by dc voltage applied to a liquid droplet on the Cytop surface, without electrical connection to the substrate. The effect is caused by the charge separation in the floating electrode. A highly resistive thermally grown SiO2 layer underneath the Cytop enables the droplet to hold charges without leakage, which is the key contribution. Electrowetting with a SiO2 layer shows a memory effect, where the wetting angle stays the same after the auxiliary electrode is removed from the droplet in both conventional and floating electrode electrowetting. Floating electrode electrowetting provides an alternative configuration for developing advanced electrowetting-based devices.

  4. Controllable Threshold Voltage in Organic Complementary Logic Circuits with an Electron-Trapping Polymer and Photoactive Gate Dielectric Layer.

    PubMed

    Dao, Toan Thanh; Sakai, Heisuke; Nguyen, Hai Thanh; Ohkubo, Kei; Fukuzumi, Shunichi; Murata, Hideyuki

    2016-07-20

    We present controllable and reliable complementary organic transistor circuits on a PET substrate using a photoactive dielectric layer of 6-[4'-(N,N-diphenylamino)phenyl]-3-ethoxycarbonylcoumarin (DPA-CM) doped into poly(methyl methacrylate) (PMMA) and an electron-trapping layer of poly(perfluoroalkenyl vinyl ether) (Cytop). Cu was used for a source/drain electrode in both the p-channel and n-channel transistors. The threshold voltage of the transistors and the inverting voltage of the circuits were reversibly controlled over a wide range under a program voltage of less than 10 V and under UV light irradiation. At a program voltage of -2 V, the inverting voltage of the circuits was tuned to be at nearly half of the supply voltage of the circuit. Consequently, an excellent balance between the high and low noise margins (NM) was produced (64% of NMH and 68% of NML), resulting in maximum noise immunity. Furthermore, the programmed circuits showed high stability, such as a retention time of over 10(5) s for the inverter switching voltage. Our findings bring about a flexible, simple way to obtain robust, high-performance organic circuits using a controllable complementary transistor inverter. PMID:27348479

  5. Supernova Remnant in 3-D

    NASA Technical Reports Server (NTRS)

    2009-01-01

    wavelengths. Since the amount of the wavelength shift is related to the speed of motion, one can determine how fast the debris are moving in either direction. Because Cas A is the result of an explosion, the stellar debris is expanding radially outwards from the explosion center. Using simple geometry, the scientists were able to construct a 3-D model using all of this information. A program called 3-D Slicer modified for astronomical use by the Astronomical Medicine Project at Harvard University in Cambridge, Mass. was used to display and manipulate the 3-D model. Commercial software was then used to create the 3-D fly-through.

    The blue filaments defining the blast wave were not mapped using the Doppler effect because they emit a different kind of light synchrotron radiation that does not emit light at discrete wavelengths, but rather in a broad continuum. The blue filaments are only a representation of the actual filaments observed at the blast wave.

    This visualization shows that there are two main components to this supernova remnant: a spherical component in the outer parts of the remnant and a flattened (disk-like) component in the inner region. The spherical component consists of the outer layer of the star that exploded, probably made of helium and carbon. These layers drove a spherical blast wave into the diffuse gas surrounding the star. The flattened component that astronomers were unable to map into 3-D prior to these Spitzer observations consists of the inner layers of the star. It is made from various heavier elements, not all shown in the visualization, such as oxygen, neon, silicon, sulphur, argon and iron.

    High-velocity plumes, or jets, of this material are shooting out from the explosion in the plane of the disk-like component mentioned above. Plumes of silicon appear in the northeast and southwest, while those of iron are seen in the southeast and north. These jets were already known and Doppler velocity measurements have been made for these

  6. Prominent rocks - 3D

    NASA Technical Reports Server (NTRS)

    1997-01-01

    Many prominent rocks near the Sagan Memorial Station are featured in this image, taken in stereo by the Imager for Mars Pathfinder (IMP) on Sol 3. 3D glasses are necessary to identify surface detail. Wedge is at lower left; Shark, Half-Dome, and Pumpkin are at center. Flat Top, about four inches high, is at lower right. The horizon in the distance is one to two kilometers away.

    Mars Pathfinder is the second in NASA's Discovery program of low-cost spacecraft with highly focused science goals. The Jet Propulsion Laboratory, Pasadena, CA, developed and manages the Mars Pathfinder mission for NASA's Office of Space Science, Washington, D.C. JPL is an operating division of the California Institute of Technology (Caltech). The Imager for Mars Pathfinder (IMP) was developed by the University of Arizona Lunar and Planetary Laboratory under contract to JPL. Peter Smith is the Principal Investigator.

    Click below to see the left and right views individually. [figure removed for brevity, see original site] Left [figure removed for brevity, see original site] Right

  7. Hierarchical dielectric orders in layered ferroelectrics Bi2SiO5

    PubMed Central

    Kim, Younghun; Kim, Jungeun; Fujiwara, Akihiko; Taniguchi, Hiroki; Kim, Sungwng; Tanaka, Hiroshi; Sugimoto, Kunihisa; Kato, Kenichi; Itoh, Mitsuru; Hosono, Hideo; Takata, Masaki

    2014-01-01

    Electric dipole engineering is now an emerging technology for high electron-mobility transistors, ferroelectric random access memory and multiferroic devices etc. Although various studies to provide insight into dipole moment behaviour, such as phase transition, order and disorder states, have been reported, macroscopic spontaneous polarization has been mainly discussed so far. Here, visualization of the electric dipole arrangement in layered ferroelectrics Bi2SiO5 by means of combined analysis of maximum entropy charge density and electrostatic potential distribution analysis based on synchrotron radiation X-ray powder diffraction data is reported. It was found that the hierarchical dipole orders, the weak-ferroelectric and ferroelectric configurations, were observed in the Bi2O2 and the SiO3 layers, respectively, and the ferrielectric configuration was realised by the interlayer interaction. This discovery provides a new method to visualize the local polarization in ferroelectric materials. PMID:25075334

  8. All dielectric hard x-ray mirror by atomic layer deposition

    SciTech Connect

    Szeghalmi, Adriana; Senz, Stephan; Goesele, Ulrich; Knez, Mato; Bretschneider, Mario

    2009-03-30

    Mirrors consisting of Al{sub 2}O{sub 3} and Ta{sub 2}O{sub 5} ({approx}2 nm film thickness) nanolaminates for hard x-ray wavelengths were produced by atomic layer deposition and characterized. Atomic force microscopy and transmission electron microscopy (TEM) proved extremely smooth surfaces of the mirrors, which are critical for highest reflectance. TEM images showed sharp interfaces between the oxides. The experimental x-ray reflectivity data were theoretically modeled and indicated minimal random thickness variations in the individual layers. Additionally, a depth graded sample with a total thickness of {approx}4 {mu}m for focusing applications in transmission (Laue) geometry and capillaries was coated.

  9. Hierarchical dielectric orders in layered ferroelectrics Bi2SiO5.

    PubMed

    Kim, Younghun; Kim, Jungeun; Fujiwara, Akihiko; Taniguchi, Hiroki; Kim, Sungwng; Tanaka, Hiroshi; Sugimoto, Kunihisa; Kato, Kenichi; Itoh, Mitsuru; Hosono, Hideo; Takata, Masaki

    2014-05-01

    Electric dipole engineering is now an emerging technology for high electron-mobility transistors, ferroelectric random access memory and multiferroic devices etc. Although various studies to provide insight into dipole moment behaviour, such as phase transition, order and disorder states, have been reported, macroscopic spontaneous polarization has been mainly discussed so far. Here, visualization of the electric dipole arrangement in layered ferroelectrics Bi2SiO5 by means of combined analysis of maximum entropy charge density and electrostatic potential distribution analysis based on synchrotron radiation X-ray powder diffraction data is reported. It was found that the hierarchical dipole orders, the weak-ferroelectric and ferroelectric configurations, were observed in the Bi2O2 and the SiO3 layers, respectively, and the ferrielectric configuration was realised by the interlayer interaction. This discovery provides a new method to visualize the local polarization in ferroelectric materials. PMID:25075334

  10. Innovations in 3D printing: a 3D overview from optics to organs.

    PubMed

    Schubert, Carl; van Langeveld, Mark C; Donoso, Larry A

    2014-02-01

    3D printing is a method of manufacturing in which materials, such as plastic or metal, are deposited onto one another in layers to produce a three dimensional object, such as a pair of eye glasses or other 3D objects. This process contrasts with traditional ink-based printers which produce a two dimensional object (ink on paper). To date, 3D printing has primarily been used in engineering to create engineering prototypes. However, recent advances in printing materials have now enabled 3D printers to make objects that are comparable with traditionally manufactured items. In contrast with conventional printers, 3D printing has the potential to enable mass customisation of goods on a large scale and has relevance in medicine including ophthalmology. 3D printing has already been proved viable in several medical applications including the manufacture of eyeglasses, custom prosthetic devices and dental implants. In this review, we discuss the potential for 3D printing to revolutionise manufacturing in the same way as the printing press revolutionised conventional printing. The applications and limitations of 3D printing are discussed; the production process is demonstrated by producing a set of eyeglass frames from 3D blueprints. PMID:24288392

  11. Fabrication of BaTiO3-Based Dielectrics for Ultrathin-Layer Multilayer Ceramic Capacitor Application by a Modified Coating Approach

    NASA Astrophysics Data System (ADS)

    Tian, Zhibin; Wang, Xiaohui; Zhang, Yichi; Song, Tae-Ho; Hur, Kang Heon; Li, Longtu

    2011-02-01

    The development of multilayer ceramic capacitor (MLCC) with base metal electrode (BME) requires precise controlling of the microstructure in a very thin dielectric layer (<1 µm). In this paper, a modified coating approach for high coverage of BaTiO3 powder for further MLCC application has been developed. The well dispersed and coated BaTiO3 powders are prepared and the relative mechanism has been discussed. Furthermore, the ultrafine grained X7R dielectric ceramics were produced by both conventional mixing and modified coating methods. Compared with the conventional mixing method, the ceramics prepared by the coating approach exhibited better TCC (the temperature coefficient of capacitance) performance, with dielectric constant over 2000 and grain size below 150 nm. In addition, it is found through the coating method the content of additives can be reduced to a relatively smaller amount than that required in conventional mixing method.

  12. Local Diagnosis of Reconnection in 3D

    NASA Astrophysics Data System (ADS)

    Scudder, J. D.; Karimabadi, H.; Daughton, W. S.; Roytershteyn, V.

    2014-12-01

    We demonstrate (I,II) an approach to find reconnection sites in 3D where there is no flux function for guidance, and where local observational signatures for the ``violation of frozen flux'' are under developed, if not non-existent. We use 2D and 3D PIC simulations of asymmetric guide field reconnection to test our observational hierarchy of single spacecraft kinetic diagnostics - all possible with present state of the art instrumentation. The proliferation of turbulent, electron inertial scale layers in the realistic 3D case demonstrates that electron demagnetization, while necessary, is not sufficient to identify reconnection sites. An excellent local, observable, single spacecraft proxy is demonstrated for the size of the theoretical frozen flux violation. Since even frozen flux violations need not imply reconnection is at hand, a new calibrated dimensionless method is used to determine the importance of such violations. This measure is available in 2D and 3D to help differentiate reconnection layers from weaker frozen flux violating layers. We discuss the possibility that this technique can be implemented on MMS. A technique to highlight flow geometries conducive to reconnection in 3D simulations is also suggested, that may also be implementable with the MMS flotilla. We use local analysis with multiple necessary, but theoretically independent electron kinetic conditions to help reduce the probability of misidentification of any given layer as a reconnection site. Since these local conditions are all necessary for the site, but none is known to be sufficient, the multiple tests help to greatly reduce false positive identifications. The selectivity of the results of this approach using PIC simulations of 3D asymmetric guide field reconnection will be shown using varying numbers of simultaneous conditions. Scudder, J.D., H. Karimabadi, W. Daughton and V. Roytershteyn I, II, submitted Phys. Plasma., 2014

  13. New coordination polymers from 1D chain, 2D layer to 3D framework constructed from 1,2-phenylenediacetic acid and 1,3-bis(4-pyridyl)propane flexible ligands

    SciTech Connect

    Xin Lingyun; Liu Guangzhen; Wang Liya

    2011-06-15

    The hydrothermal reactions of Cd, Zn, or Cu(II) acetate salts with H{sub 2}PHDA and BPP flexible ligands afford three new coordination polymers, including [Cd(PHDA)(BPP)(H{sub 2}O)]{sub n}(1), [Zn(PHDA)(BPP)]{sub n}(2), and [Cu{sub 2}(PHDA){sub 2}(BPP)]{sub n}(3) (H{sub 2}PHDA=1,2-phenylenediacetic acid, BPP=1,3-bis(4-pyridyl)propane). The single-crystal X-ray diffractions reveal that all three complexes feature various metal carboxylate subunits extended further by the BPP ligands to form a diverse range of structures, displaying a remarked structural sensitivity to metal(II) cation. Complex 1 containing PHDA-bridged binuclear cadmium generates 1D double-stranded chain, complex 2 results in 2D{yields}2D interpenetrated (4,4) grids, and complex 3 displays a 3D self-penetrated framework with 4{sup 8}6{sup 6}8 rob topology. In addition, fluorescent analyses show that both 1 and 2 exhibit intense blue-violet photoluminescence in the solid state. - Graphical Abstract: We show diverse supramolecular frameworks based on the same ligands (PHDA and BPP) and different metal acetate salts including 1D double-stranded chain, 2D {yields} 2D twofold interpenetrated layer, and 3D self-penetration networks. Highlights: > Three metal(II = 2 /* ROMAN ) coordination polymers were synthesized using H{sub 2}PHDA and BPP. > The diversity of structures show a remarked sensitivity to metal(II) center. > Complexes show the enhancement of fluorescence compared to that of free ligand.

  14. Low-frequency dielectric properties of intrinsic and Al-doped rutile TiO2 thin films grown by the atomic layer deposition technique

    NASA Astrophysics Data System (ADS)

    Kassmi, M.; Pointet, J.; Gonon, P.; Bsiesy, A.; Vallée, C.; Jomni, F.

    2016-06-01

    Dielectric spectroscopy is carried out for intrinsic and aluminum-doped TiO2 rutile films which are deposited on RuO2 by the atomic layer deposition technique. Capacitance and conductance are measured in the 0.1 Hz-100 kHz range, for ac electric fields up to 1 MVrms/cm. Intrinsic films have a much lower dielectric constant than rutile crystals. This is ascribed to the presence of oxygen vacancies which depress polarizability. When Al is substituted for Ti, the dielectric constant further decreases. By considering Al-induced modification of polarizability, a theoretical relationship between the dielectric constant and the Al concentration is proposed. Al doping drastically decreases the loss in the very low frequency part of the spectrum. However, Al doping has almost no effect on the loss at high frequencies. The effect of Al doping on loss is discussed through models of hopping transport implying intrinsic oxygen vacancies and Al related centers. When increasing the ac electric field in the MVrms/cm range, strong voltage non-linearities are evidenced in undoped films. The conductance increases exponentially with the ac field and the capacitance displays negative values (inductive behavior). Hopping barrier lowering is proposed to explain high-field effects. Finally, it is shown that Al doping strongly improves the high-field dielectric behavior.

  15. Atomic-layer-deposited Al2O3-HfO2 laminated and sandwiched dielectrics for metal insulator metal capacitors

    NASA Astrophysics Data System (ADS)

    Ding, Shi-Jin; Zhang, David Wei; Wang, Li-Kang

    2007-02-01

    Metal-insulator-metal (MIM) capacitors with atomic-layer-deposited Al2O3-HfO2 laminated and sandwiched dielectrics have been fabricated and electrically compared for analog circuit applications. The experimental results indicate that the laminated dielectrics exhibit much better leakage and breakdown characteristics than the sandwiched ones while maintaining higher capacitance densities and acceptable voltage linearity. In respect of the 1 nm Al2O3 and 10 nm HfO2 laminated dielectric, the resulting capacitor offers an extremely low leakage current of 2.4 × 10-9 A cm-2 at 8 V and a breakdown electric field of ~3.3 MV cm-1 at 125 °C together with a capacitance density of ~3.1 fF µm-2 and voltage coefficients of capacitance of 100 ppm V-2 and -80 ppm V-1 at 100 kHz. The superiority of the laminated dielectrics correlates with inhibition of HfO2 crystallization, discontinuity of the grain boundary channels from the top to the bottom and changes of the dielectric electronic properties due to the bonding and polarization effects at the multi-interfaces.

  16. MoS{sub 2} functionalization for ultra-thin atomic layer deposited dielectrics

    SciTech Connect

    Azcatl, Angelica; McDonnell, Stephen; Santosh, K.C.; Peng, Xin; Dong, Hong; Qin, Xiaoye; Addou, Rafik; Lu, Ning; Kim, Moon J.; Cho, Kyeongjae; Wallace, Robert M.; Mordi, Greg I.; Kim, Jiyoung

    2014-03-17

    The effect of room temperature ultraviolet-ozone (UV-O{sub 3}) exposure of MoS{sub 2} on the uniformity of subsequent atomic layer deposition of Al{sub 2}O{sub 3} is investigated. It is found that a UV-O{sub 3} pre-treatment removes adsorbed carbon contamination from the MoS{sub 2} surface and also functionalizes the MoS{sub 2} surface through the formation of a weak sulfur-oxygen bond without any evidence of molybdenum-sulfur bond disruption. This is supported by first principles density functional theory calculations which show that oxygen bonded to a surface sulfur atom while the sulfur is simultaneously back-bonded to three molybdenum atoms is a thermodynamically favorable configuration. The adsorbed oxygen increases the reactivity of MoS{sub 2} surface and provides nucleation sites for atomic layer deposition of Al{sub 2}O{sub 3}. The enhanced nucleation is found to be dependent on the thin film deposition temperature.

  17. Magnetic Properties of 3D Printed Toroids

    NASA Astrophysics Data System (ADS)

    Bollig, Lindsey; Otto, Austin; Hilpisch, Peter; Mowry, Greg; Nelson-Cheeseman, Brittany; Renewable Energy; Alternatives Lab (REAL) Team

    Transformers are ubiquitous in electronics today. Although toroidal geometries perform most efficiently, transformers are traditionally made with rectangular cross-sections due to the lower manufacturing costs. Additive manufacturing techniques (3D printing) can easily achieve toroidal geometries by building up a part through a series of 2D layers. To get strong magnetic properties in a 3D printed transformer, a composite filament is used containing Fe dispersed in a polymer matrix. How the resulting 3D printed toroid responds to a magnetic field depends on two structural factors of the printed 2D layers: fill factor (planar density) and fill pattern. In this work, we investigate how the fill factor and fill pattern affect the magnetic properties of 3D printed toroids. The magnetic properties of the printed toroids are measured by a custom circuit that produces a hysteresis loop for each toroid. Toroids with various fill factors and fill patterns are compared to determine how these two factors can affect the magnetic field the toroid can produce. These 3D printed toroids can be used for numerous applications in order to increase the efficiency of transformers by making it possible for manufacturers to make a toroidal geometry.

  18. Electrical conduction and dielectric relaxation properties of AlN thin films grown by hollow-cathode plasma-assisted atomic layer deposition

    NASA Astrophysics Data System (ADS)

    Altuntas, Halit; Bayrak, Turkan; Kizir, Seda; Haider, Ali; Biyikli, Necmi

    2016-07-01

    In this study, aluminum nitride (AlN) thin films were deposited at 200 °C, on p-type silicon substrates utilizing a capacitively coupled hollow-cathode plasma source integrated atomic layer deposition (ALD) reactor. The structural properties of AlN were characterized by grazing incidence x-ray diffraction, by which we confirmed the hexagonal wurtzite single-phase crystalline structure. The films exhibited an optical band edge around ∼5.7 eV. The refractive index and extinction coefficient of the AlN films were measured via a spectroscopic ellipsometer. In addition, to investigate the electrical conduction mechanisms and dielectric properties, Al/AlN/p-Si metal-insulator-semiconductor capacitor structures were fabricated, and current density–voltage and frequency dependent (7 kHz–5 MHz) dielectric constant measurements (within the strong accumulation region) were performed. A peak of dielectric loss was observed at a frequency of 3 MHz and the Cole–Davidson empirical formula was used to determine the relaxation time. It was concluded that the native point defects such as nitrogen vacancies and DX centers formed with the involvement of Si atoms into the AlN layers might have influenced the electrical conduction and dielectric relaxation properties of the plasma-assisted ALD grown AlN films.

  19. Detection of deep-subwavelength dielectric layers at terahertz frequencies using semiconductor plasmonic resonators.

    PubMed

    Berrier, Audrey; Albella, Pablo; Poyli, M Ameen; Ulbricht, Ronald; Bonn, Mischa; Aizpurua, Javier; Rivas, Jaime Gómez

    2012-02-27

    Plasmonic bowtie antennas made of doped silicon can operate as plasmonic resonators at terahertz (THz) frequencies and provide large field enhancement close to their gap. We demonstrate both experimentally and theoretically that the field confinement close to the surface of the antenna enables the detection of ultrathin (100 nm) inorganic films, about 3750 times thinner than the free space wavelength. Based on model calculations, we conclude that the detection sensitivity and its variation with the thickness of the deposited layer are related to both the decay of the local THz field profile around the antenna and the local field enhancement in the gap of the bowtie antenna. This large field enhancement has the potential to improve the detection limits of plasmon-based biological and chemical sensors. PMID:22418310

  20. Dry Etching of Organic Low Dielectric Constant Film without Etch Stop Layer

    NASA Astrophysics Data System (ADS)

    Mizumura, Michinobu; Fukuyama, Ryouji; Oomoto, Yutaka

    2002-04-01

    We investigated the trade-off between the increase of etch rate and the control of subtrenching in H2/N2 etching of a SiLK film (SiLK is a trademark of The Dow Chemical Company) without an etch stop layer for a Cu/low-k dual damascene structure. Based on our results, it is clear that the re-incident distribution of the reaction product influenced the mechanism of subtrenching strongly. As H etchant had the ability to remove the reaction product efficiently, we have successfully obtained good etching performance (an average etch rate of 128 nm/min, no subtrenching, and an etch rate uniformity of 8.9% within a 200 mm wafer) using an H2 high-flow-rate process in order to increase the amount of H etchant.

  1. Regoliths in 3-D

    NASA Technical Reports Server (NTRS)

    Grant, John; Cheng, Andrew; Delamere, Allen; Gorevan, Steven; Korotev, Randy; McKay, David; Schmitt, Harrison; Zarnecki, John

    1996-01-01

    A planetary regolith is any layer of fragments, unconsolidated material that may or may not be textually or compositionally altered relative to underlying substrate and occurs on the outer surface of a solar system body. This includes fragmented material from volcanic, sedimentary, and meteoritic infall sources, and derived by any process (e.g. impact and all other endogenic or exogenic processes). Many measurements that can be made from orbit or from Earth-based observations provide information only about the uppermost portions of a regolith and not the underlying substrate(s). Thus an understanding of the formation processes, physical properties, composition, and evolution of planetary regoliths is essential in answering scientific questions posed by the Committee on Planetary and Lunar Exploration (COMPLEX). This paper provides examples of measurements required to answer these critical science questions.

  2. MRI Volume Fusion Based on 3D Shearlet Decompositions.

    PubMed

    Duan, Chang; Wang, Shuai; Wang, Xue Gang; Huang, Qi Hong

    2014-01-01

    Nowadays many MRI scans can give 3D volume data with different contrasts, but the observers may want to view various contrasts in the same 3D volume. The conventional 2D medical fusion methods can only fuse the 3D volume data layer by layer, which may lead to the loss of interframe correlative information. In this paper, a novel 3D medical volume fusion method based on 3D band limited shearlet transform (3D BLST) is proposed. And this method is evaluated upon MRI T2* and quantitative susceptibility mapping data of 4 human brains. Both the perspective impression and the quality indices indicate that the proposed method has a better performance than conventional 2D wavelet, DT CWT, and 3D wavelet, DT CWT based fusion methods. PMID:24817880

  3. MRI Volume Fusion Based on 3D Shearlet Decompositions

    PubMed Central

    Duan, Chang; Wang, Shuai; Wang, Xue Gang; Huang, Qi Hong

    2014-01-01

    Nowadays many MRI scans can give 3D volume data with different contrasts, but the observers may want to view various contrasts in the same 3D volume. The conventional 2D medical fusion methods can only fuse the 3D volume data layer by layer, which may lead to the loss of interframe correlative information. In this paper, a novel 3D medical volume fusion method based on 3D band limited shearlet transform (3D BLST) is proposed. And this method is evaluated upon MRI T2* and quantitative susceptibility mapping data of 4 human brains. Both the perspective impression and the quality indices indicate that the proposed method has a better performance than conventional 2D wavelet, DT CWT, and 3D wavelet, DT CWT based fusion methods. PMID:24817880

  4. Supernova Remnant in 3-D

    NASA Technical Reports Server (NTRS)

    2009-01-01

    wavelengths. Since the amount of the wavelength shift is related to the speed of motion, one can determine how fast the debris are moving in either direction. Because Cas A is the result of an explosion, the stellar debris is expanding radially outwards from the explosion center. Using simple geometry, the scientists were able to construct a 3-D model using all of this information. A program called 3-D Slicer modified for astronomical use by the Astronomical Medicine Project at Harvard University in Cambridge, Mass. was used to display and manipulate the 3-D model. Commercial software was then used to create the 3-D fly-through.

    The blue filaments defining the blast wave were not mapped using the Doppler effect because they emit a different kind of light synchrotron radiation that does not emit light at discrete wavelengths, but rather in a broad continuum. The blue filaments are only a representation of the actual filaments observed at the blast wave.

    This visualization shows that there are two main components to this supernova remnant: a spherical component in the outer parts of the remnant and a flattened (disk-like) component in the inner region. The spherical component consists of the outer layer of the star that exploded, probably made of helium and carbon. These layers drove a spherical blast wave into the diffuse gas surrounding the star. The flattened component that astronomers were unable to map into 3-D prior to these Spitzer observations consists of the inner layers of the star. It is made from various heavier elements, not all shown in the visualization, such as oxygen, neon, silicon, sulphur, argon and iron.

    High-velocity plumes, or jets, of this material are shooting out from the explosion in the plane of the disk-like component mentioned above. Plumes of silicon appear in the northeast and southwest, while those of iron are seen in the southeast and north. These jets were already known and Doppler velocity measurements have been made for these

  5. Antenna with Dielectric Having Geometric Patterns

    NASA Technical Reports Server (NTRS)

    Dudley, Kenneth L. (Inventor); Elliott, Holly A. (Inventor); Cravey, Robin L. (Inventor); Connell, John W. (Inventor); Ghose, Sayata (Inventor); Watson, Kent A. (Inventor); Smith, Jr., Joseph G. (Inventor)

    2013-01-01

    An antenna includes a ground plane, a dielectric disposed on the ground plane, and an electrically-conductive radiator disposed on the dielectric. The dielectric includes at least one layer of a first dielectric material and a second dielectric material that collectively define a dielectric geometric pattern, which may comprise a fractal geometry. The radiator defines a radiator geometric pattern, and the dielectric geometric pattern is geometrically identical, or substantially geometrically identical, to the radiator geometric pattern.

  6. Improved thermal stability and electrical properties of atomic layer deposited HfO{sub 2}/AlN high-k gate dielectric stacks on GaAs

    SciTech Connect

    Cao, Yan-Qiang; Li, Xin; Zhu, Lin; Cao, Zheng-Yi; Wu, Di; Li, Ai-Dong

    2015-01-15

    The thermal stability and electrical properties of atomic layer deposited HfO{sub 2}/AlN high-k gate dielectric stacks on GaAs were investigated. Compared to HfO{sub 2}/Al{sub 2}O{sub 3} gate dielectric, significant improvements in interfacial quality as well as electrical characteristics after postdeposition annealing are confirmed by constructing HfO{sub 2}/AlN dielectric stacks. The chemical states were carefully explored by the x-ray photoelectron spectroscopy, which indicates the AlN layers effectively prevent from the formation of defective native oxides at elevated temperatures. In addition, it is found that NH{sub 3} plasma during AlN plasma-enhanced atomic layer deposition also has the self-cleaning effect as Al(CH{sub 3}){sub 3} in removing native oxides. The passivating AlN layers suppress the formation of interfacial oxide and trap charge, leading to the decrease of capacitance equivalent thickness after annealing. Moreover, HfO{sub 2}/AlN/GaAs sample has a much lower leakage current density of 2.23 × 10{sup −4} A/cm{sup 2} than HfO{sub 2}/Al{sub 2}O{sub 3}/GaAs sample of 2.58 × 10{sup −2} A/cm{sup 2}. For the HfO{sub 2}/AlN/GaAs sample annealed at 500 °C, it has a lowest interface trap density value of 2.11 × 10{sup 11} eV{sup −1} cm{sup −2}. These results indicate that adopting HfO{sub 2}/AlN dielectric stacks may be a promising approach for the realization of high quality GaAs-based transistor devices.

  7. Scoops3D: software to analyze 3D slope stability throughout a digital landscape

    USGS Publications Warehouse

    Reid, Mark E.; Christian, Sarah B.; Brien, Dianne L.; Henderson, Scott T.

    2015-01-01

    The computer program, Scoops3D, evaluates slope stability throughout a digital landscape represented by a digital elevation model (DEM). The program uses a three-dimensional (3D) method of columns approach to assess the stability of many (typically millions) potential landslides within a user-defined size range. For each potential landslide (or failure), Scoops3D assesses the stability of a rotational, spherical slip surface encompassing many DEM cells using a 3D version of either Bishop’s simplified method or the Ordinary (Fellenius) method of limit-equilibrium analysis. Scoops3D has several options for the user to systematically and efficiently search throughout an entire DEM, thereby incorporating the effects of complex surface topography. In a thorough search, each DEM cell is included in multiple potential failures, and Scoops3D records the lowest stability (factor of safety) for each DEM cell, as well as the size (volume or area) associated with each of these potential landslides. It also determines the least-stable potential failure for the entire DEM. The user has a variety of options for building a 3D domain, including layers or full 3D distributions of strength and pore-water pressures, simplistic earthquake loading, and unsaturated suction conditions. Results from Scoops3D can be readily incorporated into a geographic information system (GIS) or other visualization software. This manual includes information on the theoretical basis for the slope-stability analysis, requirements for constructing and searching a 3D domain, a detailed operational guide (including step-by-step instructions for using the graphical user interface [GUI] software, Scoops3D-i) and input/output file specifications, practical considerations for conducting an analysis, results of verification tests, and multiple examples illustrating the capabilities of Scoops3D. Easy-to-use software installation packages are available for the Windows or Macintosh operating systems; these packages

  8. A 3D Level Set Method for Microwave Breast Imaging

    PubMed Central

    Colgan, Timothy J.; Hagness, Susan C.; Van Veen, Barry D.

    2015-01-01

    Objective Conventional inverse-scattering algorithms for microwave breast imaging result in moderate resolution images with blurred boundaries between tissues. Recent 2D numerical microwave imaging studies demonstrate that the use of a level set method preserves dielectric boundaries, resulting in a more accurate, higher resolution reconstruction of the dielectric properties distribution. Previously proposed level set algorithms are computationally expensive and thus impractical in 3D. In this paper we present a computationally tractable 3D microwave imaging algorithm based on level sets. Methods We reduce the computational cost of the level set method using a Jacobian matrix, rather than an adjoint method, to calculate Frechet derivatives. We demonstrate the feasibility of 3D imaging using simulated array measurements from 3D numerical breast phantoms. We evaluate performance by comparing full 3D reconstructions to those from a conventional microwave imaging technique. We also quantitatively assess the efficacy of our algorithm in evaluating breast density. Results Our reconstructions of 3D numerical breast phantoms improve upon those of a conventional microwave imaging technique. The density estimates from our level set algorithm are more accurate than those of conventional microwave imaging, and the accuracy is greater than that reported for mammographic density estimation. Conclusion Our level set method leads to a feasible level of computational complexity for full 3D imaging, and reconstructs the heterogeneous dielectric properties distribution of the breast more accurately than conventional microwave imaging methods. Significance 3D microwave breast imaging using a level set method is a promising low-cost, non-ionizing alternative to current breast imaging techniques. PMID:26011863

  9. Influence of excess Ba concentration on the dielectric nonlinearity in Mn and V-doped BaTiO3 multi layer ceramic capacitors

    NASA Astrophysics Data System (ADS)

    Yoon, Seok-Hyun; Kim, Sun-Jung; Kim, Sang-Hyuk; Kim, Doo-Young

    2013-12-01

    The effect of excess Ba concentration on the dielectric nonlinearity was investigated in Mn and V-doped BaTiO3 multi layer ceramic capacitors (MLCC) under the same grain size condition, which was described by the Preisach model utilizing the first order reversal curve (FORC) distribution. The high-field dielectric constant and its ac field dependence dramatically changed increasing to a maximum and then decreasing with the increase of Ba concentration. The saturation polarization which scales to the magnitude of spontaneous polarization also showed similar behavior. These results indicate that the dependence of the dielectric constant on the Ba concentration is associated with the variation of both domain wall contribution and the magnitude of the spontaneous polarization, which could be correlated with the same dependence on the Ba concentration of the reversible FORC distribution at zero bias and the irreversible FORC distribution near origin. In the corresponding bulk specimens of the dielectrics of MLCC, almost the same amount of the Ba2TiSi2O8 second phases were detected irrespective of Ba concentration, which shows that the excess Ba incorporate into BaTiO3. Thus, low and high Ba concentration corresponds to Ba-deficient and Ba-rich or Ti-deficient BaTiO3, respectively, which results in a small spontaneous polarization and low domain wall density. The intermediate Ba concentration for the maximum dielectric constant is supposed to be near stoichiometric condition in the ABO3 structure corresponding to large spontaneous polarization and high domain wall density. The excess Ba concentration and its resultant A/B stoichiometry is a crucial factor controlling dielectric properties.

  10. 3D EIT image reconstruction with GREIT.

    PubMed

    Grychtol, Bartłomiej; Müller, Beat; Adler, Andy

    2016-06-01

    Most applications of thoracic EIT use a single plane of electrodes on the chest from which a transverse image 'slice' is calculated. However, interpretation of EIT images is made difficult by the large region above and below the electrode plane to which EIT is sensitive. Volumetric EIT images using two (or more) electrode planes should help compensate, but are little used currently. The Graz consensus reconstruction algorithm for EIT (GREIT) has become popular in lung EIT. One shortcoming of the original formulation of GREIT is its restriction to reconstruction onto a 2D planar image. We present an extension of the GREIT algorithm to 3D and develop open-source tools to evaluate its performance as a function of the choice of stimulation and measurement pattern. Results show 3D GREIT using two electrode layers has significantly more uniform sensitivity profiles through the chest region. Overall, the advantages of 3D EIT are compelling. PMID:27203184

  11. 3D Spectroscopy in Astronomy

    NASA Astrophysics Data System (ADS)

    Mediavilla, Evencio; Arribas, Santiago; Roth, Martin; Cepa-Nogué, Jordi; Sánchez, Francisco

    2011-09-01

    Preface; Acknowledgements; 1. Introductory review and technical approaches Martin M. Roth; 2. Observational procedures and data reduction James E. H. Turner; 3. 3D Spectroscopy instrumentation M. A. Bershady; 4. Analysis of 3D data Pierre Ferruit; 5. Science motivation for IFS and galactic studies F. Eisenhauer; 6. Extragalactic studies and future IFS science Luis Colina; 7. Tutorials: how to handle 3D spectroscopy data Sebastian F. Sánchez, Begona García-Lorenzo and Arlette Pécontal-Rousset.

  12. 3D Elevation Program—Virtual USA in 3D

    USGS Publications Warehouse

    Lukas, Vicki; Stoker, J.M.

    2016-01-01

    The U.S. Geological Survey (USGS) 3D Elevation Program (3DEP) uses a laser system called ‘lidar’ (light detection and ranging) to create a virtual reality map of the Nation that is very accurate. 3D maps have many uses with new uses being discovered all the time.  

  13. Greatly improved interfacial passivation of in-situ high κ dielectric deposition on freshly grown molecule beam epitaxy Ge epitaxial layer on Ge(100)

    SciTech Connect

    Chu, R. L.; Liu, Y. C.; Lee, W. C.; Huang, M. L.; Kwo, J. E-mail: mhong@phys.ntu.edu.tw; Lin, T. D.; Hong, M. E-mail: mhong@phys.ntu.edu.tw; Pi, T. W.

    2014-05-19

    A high-quality high-κ/Ge interface has been achieved by combining molecule beam epitaxy grown Ge epitaxial layer and in-situ deposited high κ dielectric. The employment of Ge epitaxial layer has sucessfully buried and/or removed the residue of unfavorable carbon and native oxides on the chemically cleaned and ultra-high vacuum annealed Ge(100) wafer surface, as studied using angle-resolved x-ray photoelectron spectroscopy. Moreover, the scanning tunneling microscopy analyses showed the significant improvements in Ge surface roughness from 3.5 Å to 1 Å with the epi-layer growth. Thus, chemically cleaner, atomically more ordered, and morphologically smoother Ge surfaces were obtained for the subsquent deposition of high κ dielectrics, comparing with those substrates without Ge epi-layer. The capacitance-voltage (C-V) characteristics and low extracted interfacial trap density (D{sub it}) reveal the improved high-κ/Ge interface using the Ge epi-layer approach.

  14. High dielectric constant TiO2 thin films on a Ru electrode grown at 250 °C by atomic-layer deposition

    NASA Astrophysics Data System (ADS)

    Kim, Seong Keun; Kim, Wan-Don; Kim, Kyung-Min; Hwang, Cheol Seong; Jeong, Jaehack

    2004-11-01

    TiO2 thin films with high dielectric constants (83-100) were grown on a Ru electrode at a growth temperature of 250 °C using the atomic-layer deposition method. The as-deposited films were crystallized with rutile structure. Adoption of O3 with a very high concentration (400g/m3) was crucial for obtaining the rutile phase and the high dielectric constant. The leakage current density of a TiO2 film with an equivalent oxide thickness of 1.0-1.5 nm was 10-6-10-8A/cm2 at ±1V. All these electrical properties were obtained after limited postannealing where the annealing temperature was <500°C, which is crucial to the structural stability of the Ru electrode. Therefore, these TiO2 films are very promising as the capacitor dielectrics of dynamic random access memories. TiO2 films grown on a bare Si wafer or Pt electrode by the same process had anatase structure and a dielectric constant of ˜40.

  15. Dielectric properties of novel composites prepared with few layered graphene (FLG)-lithium triniobate (LiNb{sub 3}O{sub 8})

    SciTech Connect

    Tumuluri, Anil; Raju, K. C. James; Marka, Sandeep Kumar; Srikanth, V. V. S. S.

    2015-08-28

    Lithium triniobate (LiNb{sub 3}O{sub 8}) has been prepared using microwave assisted combustion synthesis at a low temperature of 400 °C. Graphite oxide is synthesized using Hummers method and thereafter it is thermally exfoliated at 500 and 700 °C to obtain two samples of Few Layered Graphene (FLG). Then, FLG-LiNb{sub 3}O{sub 8} composites prepared through a simple ultra-sonication assisted solution mixing process. The obtained samples are named as FLN5 and FLN7 based on the temperature used to obtain FLG. Low frequency dielectric measurements are recorded for both the samples and the measured dielectric constant is observed to be more for FLN5 (250 at 60 Hz) than FLN7 (115 at 60 Hz) whilst the dielectric loss is less in case of FLN5 (1.525 at 60 Hz). The enhancement in dielectric properties for FLN5 is explained in terms of polarization in FLG-LiNb{sub 3}O{sub 8} composites.

  16. Atomic-layer-deposited Al2O3-HfO2-Al2O3 dielectrics for metal-insulator-metal capacitor applications

    NASA Astrophysics Data System (ADS)

    Ding, Shi-Jin; Zhu, Chunxiang; Li, Ming-Fu; Zhang, David Wei

    2005-08-01

    Atomic-layer-deposited Al2O3-HfO2-Al2O3 dielectrics have been investigated to replace conventional silicon oxide and nitride for radio frequency and analog metal-insulator-metal capacitors applications. In the case of 1-nm-Al2O3, sufficiently good electrical performances are achieved, including a high dielectric constant of ˜17, a small dissipation factor of 0.018 at 100kHz, an extremely low leakage current of 7.8×10-9A/cm2 at 1MV/cm and 125°C, perfect voltage coefficients of capacitance (74ppm/V2 and 10ppm/V). The quadratic voltage coefficient of capacitance decreases with the applied frequency due to the change of relaxation time with different carrier mobility in insulator, and correlates with the dielectric composition and thickness, which is of intrinsic property owing to electric field polarization. Furthermore, the conduction mechanism of the AHA dielectrics is also discussed, indicating the Schottky emission dominated at room temperature.

  17. bioWeb3D: an online webGL 3D data visualisation tool

    PubMed Central

    2013-01-01

    Background Data visualization is critical for interpreting biological data. However, in practice it can prove to be a bottleneck for non trained researchers; this is especially true for three dimensional (3D) data representation. Whilst existing software can provide all necessary functionalities to represent and manipulate biological 3D datasets, very few are easily accessible (browser based), cross platform and accessible to non-expert users. Results An online HTML5/WebGL based 3D visualisation tool has been developed to allow biologists to quickly and easily view interactive and customizable three dimensional representations of their data along with multiple layers of information. Using the WebGL library Three.js written in Javascript, bioWeb3D allows the simultaneous visualisation of multiple large datasets inputted via a simple JSON, XML or CSV file, which can be read and analysed locally thanks to HTML5 capabilities. Conclusions Using basic 3D representation techniques in a technologically innovative context, we provide a program that is not intended to compete with professional 3D representation software, but that instead enables a quick and intuitive representation of reasonably large 3D datasets. PMID:23758781

  18. Modular 3-D Transport model

    EPA Science Inventory

    MT3D was first developed by Chunmiao Zheng in 1990 at S.S. Papadopulos & Associates, Inc. with partial support from the U.S. Environmental Protection Agency (USEPA). Starting in 1990, MT3D was released as a pubic domain code from the USEPA. Commercial versions with enhanced capab...

  19. Market study: 3-D eyetracker

    NASA Technical Reports Server (NTRS)

    1977-01-01

    A market study of a proposed version of a 3-D eyetracker for initial use at NASA's Ames Research Center was made. The commercialization potential of a simplified, less expensive 3-D eyetracker was ascertained. Primary focus on present and potential users of eyetrackers, as well as present and potential manufacturers has provided an effective means of analyzing the prospects for commercialization.

  20. LLNL-Earth3D

    2013-10-01

    Earth3D is a computer code designed to allow fast calculation of seismic rays and travel times through a 3D model of the Earth. LLNL is using this for earthquake location and global tomography efforts and such codes are of great interest to the Earth Science community.

  1. [3-D ultrasound in gastroenterology].

    PubMed

    Zoller, W G; Liess, H

    1994-06-01

    Three-dimensional (3D) sonography represents a development of noninvasive diagnostic imaging by real-time two-dimensional (2D) sonography. The use of transparent rotating scans, comparable to a block of glass, generates a 3D effect. The objective of the present study was to optimate 3D presentation of abdominal findings. Additional investigations were made with a new volumetric program to determine the volume of selected findings of the liver. The results were compared with the estimated volumes of 2D sonography and 2D computer tomography (CT). For the processing of 3D images, typical parameter constellations were found for the different findings, which facilitated processing of 3D images. In more than 75% of the cases examined we found an optimal 3D presentation of sonographic findings with respect to the evaluation criteria developed by us for the 3D imaging of processed data. Great differences were found for the estimated volumes of the findings of the liver concerning the three different techniques applied. 3D ultrasound represents a valuable method to judge morphological appearance in abdominal findings. The possibility of volumetric measurements enlarges its potential diagnostic significance. Further clinical investigations are necessary to find out if definite differentiation between benign and malign findings is possible. PMID:7919882

  2. 3D World Building System

    SciTech Connect

    2013-10-30

    This video provides an overview of the Sandia National Laboratories developed 3-D World Model Building capability that provides users with an immersive, texture rich 3-D model of their environment in minutes using a laptop and color and depth camera.

  3. 3D World Building System

    ScienceCinema

    None

    2014-02-26

    This video provides an overview of the Sandia National Laboratories developed 3-D World Model Building capability that provides users with an immersive, texture rich 3-D model of their environment in minutes using a laptop and color and depth camera.

  4. Charge injection in thin dielectric layers by atomic force microscopy: influence of geometry and material work function of the AFM tip on the injection process

    NASA Astrophysics Data System (ADS)

    Villeneuve-Faure, C.; Makasheva, K.; Boudou, L.; Teyssedre, G.

    2016-06-01

    Charge injection and retention in thin dielectric layers remain critical issues for the reliability of many electronic devices because of their association with a large number of failure mechanisms. To overcome this drawback, a deep understanding of the mechanisms leading to charge injection close to the injection area is needed. Even though the charge injection is extensively studied and reported in the literature to characterize the charge storage capability of dielectric materials, questions about charge injection mechanisms when using atomic force microscopy (AFM) remain open. In this paper, a thorough study of charge injection by using AFM in thin plasma-processed amorphous silicon oxynitride layers with properties close to that of thermal silica layers is presented. The study considers the impact of applied voltage polarity, work function of the AFM tip coating and tip curvature radius. A simple theoretical model was developed and used to analyze the obtained experimental results. The electric field distribution is computed as a function of tip geometry. The obtained experimental results highlight that after injection in the dielectric layer the charge lateral spreading is mainly controlled by the radial electric field component independently of the carrier polarity. The injected charge density is influenced by the nature of electrode metal coating (work function) and its geometry (tip curvature radius). The electron injection is mainly ruled by the Schottky injection barrier through the field electron emission mechanism enhanced by thermionic electron emission. The hole injection mechanism seems to differ from the electron one depending on the work function of the metal coating. Based on the performed analysis, it is suggested that for hole injection by AFM, pinning of the metal Fermi level with the metal-induced gap states in the studied silicon oxynitride layers starts playing a role in the injection mechanisms.

  5. Charge injection in thin dielectric layers by atomic force microscopy: influence of geometry and material work function of the AFM tip on the injection process.

    PubMed

    Villeneuve-Faure, C; Makasheva, K; Boudou, L; Teyssedre, G

    2016-06-17

    Charge injection and retention in thin dielectric layers remain critical issues for the reliability of many electronic devices because of their association with a large number of failure mechanisms. To overcome this drawback, a deep understanding of the mechanisms leading to charge injection close to the injection area is needed. Even though the charge injection is extensively studied and reported in the literature to characterize the charge storage capability of dielectric materials, questions about charge injection mechanisms when using atomic force microscopy (AFM) remain open. In this paper, a thorough study of charge injection by using AFM in thin plasma-processed amorphous silicon oxynitride layers with properties close to that of thermal silica layers is presented. The study considers the impact of applied voltage polarity, work function of the AFM tip coating and tip curvature radius. A simple theoretical model was developed and used to analyze the obtained experimental results. The electric field distribution is computed as a function of tip geometry. The obtained experimental results highlight that after injection in the dielectric layer the charge lateral spreading is mainly controlled by the radial electric field component independently of the carrier polarity. The injected charge density is influenced by the nature of electrode metal coating (work function) and its geometry (tip curvature radius). The electron injection is mainly ruled by the Schottky injection barrier through the field electron emission mechanism enhanced by thermionic electron emission. The hole injection mechanism seems to differ from the electron one depending on the work function of the metal coating. Based on the performed analysis, it is suggested that for hole injection by AFM, pinning of the metal Fermi level with the metal-induced gap states in the studied silicon oxynitride layers starts playing a role in the injection mechanisms. PMID:27158768

  6. Euro3D Science Conference

    NASA Astrophysics Data System (ADS)

    Walsh, J. R.

    2004-02-01

    The Euro3D RTN is an EU funded Research Training Network to foster the exploitation of 3D spectroscopy in Europe. 3D spectroscopy is a general term for spectroscopy of an area of the sky and derives its name from its two spatial + one spectral dimensions. There are an increasing number of instruments which use integral field devices to achieve spectroscopy of an area of the sky, either using lens arrays, optical fibres or image slicers, to pack spectra of multiple pixels on the sky (``spaxels'') onto a 2D detector. On account of the large volume of data and the special methods required to reduce and analyse 3D data, there are only a few centres of expertise and these are mostly involved with instrument developments. There is a perceived lack of expertise in 3D spectroscopy spread though the astronomical community and its use in the armoury of the observational astronomer is viewed as being highly specialised. For precisely this reason the Euro3D RTN was proposed to train young researchers in this area and develop user tools to widen the experience with this particular type of data in Europe. The Euro3D RTN is coordinated by Martin M. Roth (Astrophysikalisches Institut Potsdam) and has been running since July 2002. The first Euro3D science conference was held in Cambridge, UK from 22 to 23 May 2003. The main emphasis of the conference was, in keeping with the RTN, to expose the work of the young post-docs who are funded by the RTN. In addition the team members from the eleven European institutes involved in Euro3D also presented instrumental and observational developments. The conference was organized by Andy Bunker and held at the Institute of Astronomy. There were over thirty participants and 26 talks covered the whole range of application of 3D techniques. The science ranged from Galactic planetary nebulae and globular clusters to kinematics of nearby galaxies out to objects at high redshift. Several talks were devoted to reporting recent observations with newly

  7. PLOT3D user's manual

    NASA Technical Reports Server (NTRS)

    Walatka, Pamela P.; Buning, Pieter G.; Pierce, Larry; Elson, Patricia A.

    1990-01-01

    PLOT3D is a computer graphics program designed to visualize the grids and solutions of computational fluid dynamics. Seventy-four functions are available. Versions are available for many systems. PLOT3D can handle multiple grids with a million or more grid points, and can produce varieties of model renderings, such as wireframe or flat shaded. Output from PLOT3D can be used in animation programs. The first part of this manual is a tutorial that takes the reader, keystroke by keystroke, through a PLOT3D session. The second part of the manual contains reference chapters, including the helpfile, data file formats, advice on changing PLOT3D, and sample command files.

  8. 3D printing in dentistry.

    PubMed

    Dawood, A; Marti Marti, B; Sauret-Jackson, V; Darwood, A

    2015-12-01

    3D printing has been hailed as a disruptive technology which will change manufacturing. Used in aerospace, defence, art and design, 3D printing is becoming a subject of great interest in surgery. The technology has a particular resonance with dentistry, and with advances in 3D imaging and modelling technologies such as cone beam computed tomography and intraoral scanning, and with the relatively long history of the use of CAD CAM technologies in dentistry, it will become of increasing importance. Uses of 3D printing include the production of drill guides for dental implants, the production of physical models for prosthodontics, orthodontics and surgery, the manufacture of dental, craniomaxillofacial and orthopaedic implants, and the fabrication of copings and frameworks for implant and dental restorations. This paper reviews the types of 3D printing technologies available and their various applications in dentistry and in maxillofacial surgery. PMID:26657435

  9. High-performance enhancement-mode AlGaN/GaN MOS-HEMTs with fluorinated stack gate dielectrics and thin barrier layer

    NASA Astrophysics Data System (ADS)

    Tao, Gao; Ruimin, Xu; Kai, Zhang; Yuechan, Kong; Jianjun, Zhou; Cen, Kong; Xinxin, Yu; Xun, Dong; Tangsheng, Chen

    2016-06-01

    We present high-performance enhancement-mode AlGaN/GaN metal—oxide—semiconductor high-electron mobility transistors (MOS-HEMTs) by a fluorinated gate dielectric technique. A nanolaminate of an Al2O3/La x Al1‑x O 3/Al2O3 stack (x≈0.33) grown by atomic layer deposition is employed to avoid fluorine ions implantation into the scaled barrier layer. Fabricated enhancement-mode MOS-HEMTs exhibit an excellent performance as compared to those with the conventional dielectric-last technique, delivering a large maximum drain current of 916 mA/mm and simultaneously a high peak transconductance of 342 mS/mm. The balanced DC characteristics indicate that advanced gate stack dielectrics combined with buffered fluorine ions implantation have a great potential for high speed GaN E/D-mode integrated circuit applications. Project supported by the National Natural Science Foundation of China (Nos. 61504125, 61474101, 61106130 61076120, 61505181), and the Natural Science Foundation of Jiangsu Province of China (Nos. BK20131072, BE2012007, BK2012516).

  10. In situ atomic layer nitridation on the top and down regions of the amorphous and crystalline high-K gate dielectrics

    NASA Astrophysics Data System (ADS)

    Tsai, Meng-Chen; Lee, Min-Hung; Kuo, Chin-Lung; Lin, Hsin-Chih; Chen, Miin-Jang

    2016-11-01

    Amorphous and crystalline ZrO2 gate dielectrics treated with in situ atomic layer nitridation on the top and down regions (top and down nitridation, abbreviated as TN and DN) were investigated. In a comparison between the as-deposited amorphous DN and TN samples, the DN sample has a lower leakage current density (Jg) of ∼7 × 10-4 A/cm2 with a similar capacitance equivalent thickness (CET) of ∼1.53 nm, attributed to the formation of SiOxNy in the interfacial layer (IL). The post-metallization annealing (PMA) leads to the transformation of ZrO2 from the amorphous to the crystalline tetragonal/cubic phase, resulting in an increment of the dielectric constant. The PMA-treated TN sample exhibits a lower CET of 1.22 nm along with a similar Jg of ∼1.4 × 10-5 A/cm2 as compared with the PMA-treated DN sample, which can be ascribed to the suppression of IL regrowth. The result reveals that the nitrogen engineering in the top and down regions has a significant impact on the electrical characteristics of amorphous and crystalline ZrO2 gate dielectrics, and the nitrogen incorporation at the top of crystalline ZrO2 is an effective approach to scale the CET and Jg, as well as to improve the reliability.

  11. PLOT3D/AMES, APOLLO UNIX VERSION USING GMR3D (WITH TURB3D)

    NASA Technical Reports Server (NTRS)

    Buning, P.

    1994-01-01

    PLOT3D is an interactive graphics program designed to help scientists visualize computational fluid dynamics (CFD) grids and solutions. Today, supercomputers and CFD algorithms can provide scientists with simulations of such highly complex phenomena that obtaining an understanding of the simulations has become a major problem. Tools which help the scientist visualize the simulations can be of tremendous aid. PLOT3D/AMES offers more functions and features, and has been adapted for more types of computers than any other CFD graphics program. Version 3.6b+ is supported for five computers and graphic libraries. Using PLOT3D, CFD physicists can view their computational models from any angle, observing the physics of problems and the quality of solutions. As an aid in designing aircraft, for example, PLOT3D's interactive computer graphics can show vortices, temperature, reverse flow, pressure, and dozens of other characteristics of air flow during flight. As critical areas become obvious, they can easily be studied more closely using a finer grid. PLOT3D is part of a computational fluid dynamics software cycle. First, a program such as 3DGRAPE (ARC-12620) helps the scientist generate computational grids to model an object and its surrounding space. Once the grids have been designed and parameters such as the angle of attack, Mach number, and Reynolds number have been specified, a "flow-solver" program such as INS3D (ARC-11794 or COS-10019) solves the system of equations governing fluid flow, usually on a supercomputer. Grids sometimes have as many as two million points, and the "flow-solver" produces a solution file which contains density, x- y- and z-momentum, and stagnation energy for each grid point. With such a solution file and a grid file containing up to 50 grids as input, PLOT3D can calculate and graphically display any one of 74 functions, including shock waves, surface pressure, velocity vectors, and particle traces. PLOT3D's 74 functions are organized into

  12. PLOT3D/AMES, APOLLO UNIX VERSION USING GMR3D (WITHOUT TURB3D)

    NASA Technical Reports Server (NTRS)

    Buning, P.

    1994-01-01

    PLOT3D is an interactive graphics program designed to help scientists visualize computational fluid dynamics (CFD) grids and solutions. Today, supercomputers and CFD algorithms can provide scientists with simulations of such highly complex phenomena that obtaining an understanding of the simulations has become a major problem. Tools which help the scientist visualize the simulations can be of tremendous aid. PLOT3D/AMES offers more functions and features, and has been adapted for more types of computers than any other CFD graphics program. Version 3.6b+ is supported for five computers and graphic libraries. Using PLOT3D, CFD physicists can view their computational models from any angle, observing the physics of problems and the quality of solutions. As an aid in designing aircraft, for example, PLOT3D's interactive computer graphics can show vortices, temperature, reverse flow, pressure, and dozens of other characteristics of air flow during flight. As critical areas become obvious, they can easily be studied more closely using a finer grid. PLOT3D is part of a computational fluid dynamics software cycle. First, a program such as 3DGRAPE (ARC-12620) helps the scientist generate computational grids to model an object and its surrounding space. Once the grids have been designed and parameters such as the angle of attack, Mach number, and Reynolds number have been specified, a "flow-solver" program such as INS3D (ARC-11794 or COS-10019) solves the system of equations governing fluid flow, usually on a supercomputer. Grids sometimes have as many as two million points, and the "flow-solver" produces a solution file which contains density, x- y- and z-momentum, and stagnation energy for each grid point. With such a solution file and a grid file containing up to 50 grids as input, PLOT3D can calculate and graphically display any one of 74 functions, including shock waves, surface pressure, velocity vectors, and particle traces. PLOT3D's 74 functions are organized into

  13. Complex light in 3D printing

    NASA Astrophysics Data System (ADS)

    Moser, Christophe; Delrot, Paul; Loterie, Damien; Morales Delgado, Edgar; Modestino, Miguel; Psaltis, Demetri

    2016-03-01

    3D printing as a tool to generate complicated shapes from CAD files, on demand, with different materials from plastics to metals, is shortening product development cycles, enabling new design possibilities and can provide a mean to manufacture small volumes cost effectively. There are many technologies for 3D printing and the majority uses light in the process. In one process (Multi-jet modeling, polyjet, printoptical©), a printhead prints layers of ultra-violet curable liquid plastic. Here, each nozzle deposits the material, which is then flooded by a UV curing lamp to harden it. In another process (Stereolithography), a focused UV laser beam provides both the spatial localization and the photo-hardening of the resin. Similarly, laser sintering works with metal powders by locally melting the material point by point and layer by layer. When the laser delivers ultra-fast focused pulses, nonlinear effects polymerize the material with high spatial resolution. In these processes, light is either focused in one spot and the part is made by scanning it or the light is expanded and covers a wide area for photopolymerization. Hence a fairly "simple" light field is used in both cases. Here, we give examples of how "complex light" brings additional level of complexity in 3D printing.

  14. Science and technology of thin films and interfacial layers in ferroelectric and high-dielectric constant heterostructures and application to devices.

    SciTech Connect

    Auciello, O.; Materials Science Division

    2006-01-01

    The fabrication of the next generation of complex oxide thin film-based micro and nanoscale devices, such as, for example, low and high density nonvolatile ferroelectric random access memories (FeRAMS), high-dielectric constant (K) high-frequency devices, and the next generation of complimentary metal oxide semiconductor (CMOS) nanoscale devices based on high-K dielectrics, require understanding and control of film growth and interface processes as well as development of materials integration strategies with atomic scale control. In recent years, we developed and applied a unique combination of integrated film synthesis/in situ characterization and ex situ analytical techniques capable of providing information about thin film surface and interface processes at the atomic scale as required for the development of the devices mentioned above. These techniques are also useful for establishing composition-microstructure-property relationships critical for the integration of oxide thin films with semiconductor device platforms for the development of a whole new generation of micro and nanodevices based on film technologies beyond semiconductors and specifically silicon. Our recent work has been focused on developing diffusion barrier layers and heterostructured bottom electrodes that play a critical role in high-density FeRAM integration. We demonstrated that TiAl layers can be used as a material with a double diffusion barrier/bottom electrode functionality for integration of ferroelectric capacitors CMOS devices for fabrication of FeRAMs. We also demonstrated that control of interfaces is critical to the integration of high-K dielectric films with appropriate substrates for the fabrication of high-performance high-frequency devices, and here again a diffusion barrier such as the TiAl layer developed by our group is critical for such integration. These studies revealed that when properly oxidized, nanoscale thick amorphous Ti-Al-O layers exhibit properties that make

  15. Unassisted 3D camera calibration

    NASA Astrophysics Data System (ADS)

    Atanassov, Kalin; Ramachandra, Vikas; Nash, James; Goma, Sergio R.

    2012-03-01

    With the rapid growth of 3D technology, 3D image capture has become a critical part of the 3D feature set on mobile phones. 3D image quality is affected by the scene geometry as well as on-the-device processing. An automatic 3D system usually assumes known camera poses accomplished by factory calibration using a special chart. In real life settings, pose parameters estimated by factory calibration can be negatively impacted by movements of the lens barrel due to shaking, focusing, or camera drop. If any of these factors displaces the optical axes of either or both cameras, vertical disparity might exceed the maximum tolerable margin and the 3D user may experience eye strain or headaches. To make 3D capture more practical, one needs to consider unassisted (on arbitrary scenes) calibration. In this paper, we propose an algorithm that relies on detection and matching of keypoints between left and right images. Frames containing erroneous matches, along with frames with insufficiently rich keypoint constellations, are detected and discarded. Roll, pitch yaw , and scale differences between left and right frames are then estimated. The algorithm performance is evaluated in terms of the remaining vertical disparity as compared to the maximum tolerable vertical disparity.

  16. Significance of the double-layer capacitor effect in polar rubbery dielectrics and exceptionally stable low-voltage high transconductance organic transistors

    PubMed Central

    Wang, Chao; Lee, Wen-Ya; Kong, Desheng; Pfattner, Raphael; Schweicher, Guillaume; Nakajima, Reina; Lu, Chien; Mei, Jianguo; Lee, Tae Hoon; Wu, Hung-Chin; Lopez, Jeffery; Diao, Ying; Gu, Xiaodan; Himmelberger, Scott; Niu, Weijun; Matthews, James R.; He, Mingqian; Salleo, Alberto; Nishi, Yoshio; Bao, Zhenan

    2015-01-01

    Both high gain and transconductance at low operating voltages are essential for practical applications of organic field-effect transistors (OFETs). Here, we describe the significance of the double-layer capacitance effect in polar rubbery dielectrics, even when present in a very low ion concentration and conductivity. We observed that this effect can greatly enhance the OFET transconductance when driven at low voltages. Specifically, when the polar elastomer poly(vinylidene fluoride-co-hexafluoropropylene) (e-PVDF-HFP) was used as the dielectric layer, despite a thickness of several micrometers, we obtained a transconductance per channel width 30 times higher than that measured for the same organic semiconductors fabricated on a semicrystalline PVDF-HFP with a similar thickness. After a series of detailed experimental investigations, we attribute the above observation to the double-layer capacitance effect, even though the ionic conductivity is as low as 10–10 S/cm. Different from previously reported OFETs with double-layer capacitance effects, our devices showed unprecedented high bias-stress stability in air and even in water. PMID:26658331

  17. Significance of the double-layer capacitor effect in polar rubbery dielectrics and exceptionally stable low-voltage high transconductance organic transistors.

    PubMed

    Wang, Chao; Lee, Wen-Ya; Kong, Desheng; Pfattner, Raphael; Schweicher, Guillaume; Nakajima, Reina; Lu, Chien; Mei, Jianguo; Lee, Tae Hoon; Wu, Hung-Chin; Lopez, Jeffery; Diao, Ying; Gu, Xiaodan; Himmelberger, Scott; Niu, Weijun; Matthews, James R; He, Mingqian; Salleo, Alberto; Nishi, Yoshio; Bao, Zhenan

    2015-01-01

    Both high gain and transconductance at low operating voltages are essential for practical applications of organic field-effect transistors (OFETs). Here, we describe the significance of the double-layer capacitance effect in polar rubbery dielectrics, even when present in a very low ion concentration and conductivity. We observed that this effect can greatly enhance the OFET transconductance when driven at low voltages. Specifically, when the polar elastomer poly(vinylidene fluoride-co-hexafluoropropylene) (e-PVDF-HFP) was used as the dielectric layer, despite a thickness of several micrometers, we obtained a transconductance per channel width 30 times higher than that measured for the same organic semiconductors fabricated on a semicrystalline PVDF-HFP with a similar thickness. After a series of detailed experimental investigations, we attribute the above observation to the double-layer capacitance effect, even though the ionic conductivity is as low as 10(-10) S/cm. Different from previously reported OFETs with double-layer capacitance effects, our devices showed unprecedented high bias-stress stability in air and even in water. PMID:26658331

  18. Significance of the double-layer capacitor effect in polar rubbery dielectrics and exceptionally stable low-voltage high transconductance organic transistors

    NASA Astrophysics Data System (ADS)

    Wang, Chao; Lee, Wen-Ya; Kong, Desheng; Pfattner, Raphael; Schweicher, Guillaume; Nakajima, Reina; Lu, Chien; Mei, Jianguo; Lee, Tae Hoon; Wu, Hung-Chin; Lopez, Jeffery; Diao, Ying; Gu, Xiaodan; Himmelberger, Scott; Niu, Weijun; Matthews, James R.; He, Mingqian; Salleo, Alberto; Nishi, Yoshio; Bao, Zhenan

    2015-12-01

    Both high gain and transconductance at low operating voltages are essential for practical applications of organic field-effect transistors (OFETs). Here, we describe the significance of the double-layer capacitance effect in polar rubbery dielectrics, even when present in a very low ion concentration and conductivity. We observed that this effect can greatly enhance the OFET transconductance when driven at low voltages. Specifically, when the polar elastomer poly(vinylidene fluoride-co-hexafluoropropylene) (e-PVDF-HFP) was used as the dielectric layer, despite a thickness of several micrometers, we obtained a transconductance per channel width 30 times higher than that measured for the same organic semiconductors fabricated on a semicrystalline PVDF-HFP with a similar thickness. After a series of detailed experimental investigations, we attribute the above observation to the double-layer capacitance effect, even though the ionic conductivity is as low as 10-10 S/cm. Different from previously reported OFETs with double-layer capacitance effects, our devices showed unprecedented high bias-stress stability in air and even in water.

  19. Hydrogen bond network in the hydration layer of the water confined in nanotubes increasing the dielectric constant parallel along the nanotube axis.

    PubMed

    Qi, Wenpeng; Zhao, Hongwei

    2015-09-21

    The water confined in nanotubes has been extensively studied, because of the potential usages in drug delivery and desalination. The radial distribution of the dielectric constant parallel along the nanotube axis was obtained by molecular dynamics simulations in a carbon nanotube and a nanotube with a very small van der Waals potential. The confined water was divided into two parts, the middle part water and the hydration water. In both cases, the hydrogen bond orientation of the middle water is isotropic, while the hydrogen bonds in hydration layers are apt to parallel along the nanotube axis. Therefore, the hydration water has higher dipole correlations increasing the dielectric constant along the nanotube axis. PMID:26395729

  20. Fdf in US3D

    NASA Astrophysics Data System (ADS)

    Otis, Collin; Ferrero, Pietro; Candler, Graham; Givi, Peyman

    2013-11-01

    The scalar filtered mass density function (SFMDF) methodology is implemented into the computer code US3D. This is an unstructured Eulerian finite volume hydrodynamic solver and has proven very effective for simulation of compressible turbulent flows. The resulting SFMDF-US3D code is employed for large eddy simulation (LES) on unstructured meshes. Simulations are conducted of subsonic and supersonic flows under non-reacting and reacting conditions. The consistency and the accuracy of the simulated results are assessed along with appraisal of the overall performance of the methodology. The SFMDF-US3D is now capable of simulating high speed flows in complex configurations.

  1. Wavefront construction in 3-D

    SciTech Connect

    Chilcoat, S.R. Hildebrand, S.T.

    1995-12-31

    Travel time computation in inhomogeneous media is essential for pre-stack Kirchhoff imaging in areas such as the sub-salt province in the Gulf of Mexico. The 2D algorithm published by Vinje, et al, has been extended to 3D to compute wavefronts in complicated inhomogeneous media. The 3D wavefront construction algorithm provides many advantages over conventional ray tracing and other methods of computing travel times in 3D. The algorithm dynamically maintains a reasonably consistent ray density without making a priori guesses at the number of rays to shoot. The determination of caustics in 3D is a straight forward geometric procedure. The wavefront algorithm also enables the computation of multi-valued travel time surfaces.

  2. Heterodyne 3D ghost imaging

    NASA Astrophysics Data System (ADS)

    Yang, Xu; Zhang, Yong; Yang, Chenghua; Xu, Lu; Wang, Qiang; Zhao, Yuan

    2016-06-01

    Conventional three dimensional (3D) ghost imaging measures range of target based on pulse fight time measurement method. Due to the limit of data acquisition system sampling rate, range resolution of the conventional 3D ghost imaging is usually low. In order to take off the effect of sampling rate to range resolution of 3D ghost imaging, a heterodyne 3D ghost imaging (HGI) system is presented in this study. The source of HGI is a continuous wave laser instead of pulse laser. Temporal correlation and spatial correlation of light are both utilized to obtain the range image of target. Through theory analysis and numerical simulations, it is demonstrated that HGI can obtain high range resolution image with low sampling rate.

  3. Combinatorial 3D Mechanical Metamaterials

    NASA Astrophysics Data System (ADS)

    Coulais, Corentin; Teomy, Eial; de Reus, Koen; Shokef, Yair; van Hecke, Martin

    2015-03-01

    We present a class of elastic structures which exhibit 3D-folding motion. Our structures consist of cubic lattices of anisotropic unit cells that can be tiled in a complex combinatorial fashion. We design and 3d-print this complex ordered mechanism, in which we combine elastic hinges and defects to tailor the mechanics of the material. Finally, we use this large design space to encode smart functionalities such as surface patterning and multistability.

  4. Bottom-up Fabrication of Multilayer Stacks of 3D Photonic Crystals from Titanium Dioxide.

    PubMed

    Kubrin, Roman; Pasquarelli, Robert M; Waleczek, Martin; Lee, Hooi Sing; Zierold, Robert; do Rosário, Jefferson J; Dyachenko, Pavel N; Montero Moreno, Josep M; Petrov, Alexander Yu; Janssen, Rolf; Eich, Manfred; Nielsch, Kornelius; Schneider, Gerold A

    2016-04-27

    A strategy for stacking multiple ceramic 3D photonic crystals is developed. Periodically structured porous films are produced by vertical convective self-assembly of polystyrene (PS) microspheres. After infiltration of the opaline templates by atomic layer deposition (ALD) of titania and thermal decomposition of the polystyrene matrix, a ceramic 3D photonic crystal is formed. Further layers with different sizes of pores are deposited subsequently by repetition of the process. The influence of process parameters on morphology and photonic properties of double and triple stacks is systematically studied. Prolonged contact of amorphous titania films with warm water during self-assembly of the successive templates is found to result in exaggerated roughness of the surfaces re-exposed to ALD. Random scattering on rough internal surfaces disrupts ballistic transport of incident photons into deeper layers of the multistacks. Substantially smoother interfaces are obtained by calcination of the structure after each infiltration, which converts amorphous titania into the crystalline anatase before resuming the ALD infiltration. High quality triple stacks consisting of anatase inverse opals with different pore sizes are demonstrated for the first time. The elaborated fabrication method shows promise for various applications demanding broadband dielectric reflectors or titania photonic crystals with a long mean free path of photons. PMID:27045887

  5. Comparison of equivalent oxide thickness and electrical properties of atomic layer deposited hafnium zirconate dielectrics with thermal or decoupled plasma nitridation process

    NASA Astrophysics Data System (ADS)

    Chiang, Chen-Kuo; Wu, Chien-Hung; Liu, Chin-Chien; Lin, Jin-Fu; Yang, Chien-Lun; Wu, Jiun-Yuan; Wang, Shui-Jinn

    2012-10-01

    The NH3 thermal annealing and decoupled plasma nitridation (DPN) processes are compared for the equivalent oxide thickness (EOT) scaling of atomic-layer-deposited hafnium zirconate (HfZrO2) gate dielectric. Detailed physical, optical, and electrical characteristics of nitrided HfZrO2 (HfZrON) film are reported. It is found that DPN can yield a thinner SiOx interfacial layer (IL) (about 0.12 nm more in terms of EOT scaling) and a more densified HfZrO2 layer compared to those obtained using NH3 thermal annealing at a 16% nitrogen dose. NH3 thermal nitridation causes a large nitrogen distribution tail at the SiOx IL/Si substrate interface and increases leakage current, which suppresses EOT scalability.

  6. Multizone Paper Platform for 3D Cell Cultures

    PubMed Central

    Derda, Ratmir; Hong, Estrella; Mwangi, Martin; Mammoto, Akiko; Ingber, Donald E.; Whitesides, George M.

    2011-01-01

    In vitro 3D culture is an important model for tissues in vivo. Cells in different locations of 3D tissues are physiologically different, because they are exposed to different concentrations of oxygen, nutrients, and signaling molecules, and to other environmental factors (temperature, mechanical stress, etc). The majority of high-throughput assays based on 3D cultures, however, can only detect the average behavior of cells in the whole 3D construct. Isolation of cells from specific regions of 3D cultures is possible, but relies on low-throughput techniques such as tissue sectioning and micromanipulation. Based on a procedure reported previously (“cells-in-gels-in-paper” or CiGiP), this paper describes a simple method for culture of arrays of thin planar sections of tissues, either alone or stacked to create more complex 3D tissue structures. This procedure starts with sheets of paper patterned with hydrophobic regions that form 96 hydrophilic zones. Serial spotting of cells suspended in extracellular matrix (ECM) gel onto the patterned paper creates an array of 200 micron-thick slabs of ECM gel (supported mechanically by cellulose fibers) containing cells. Stacking the sheets with zones aligned on top of one another assembles 96 3D multilayer constructs. De-stacking the layers of the 3D culture, by peeling apart the sheets of paper, “sections” all 96 cultures at once. It is, thus, simple to isolate 200-micron-thick cell-containing slabs from each 3D culture in the 96-zone array. Because the 3D cultures are assembled from multiple layers, the number of cells plated initially in each layer determines the spatial distribution of cells in the stacked 3D cultures. This capability made it possible to compare the growth of 3D tumor models of different spatial composition, and to examine the migration of cells in these structures. PMID:21573103

  7. Influence of temperature on the dielectric nonlinearity of BaTiO3-based multi-layer ceramic capacitors

    NASA Astrophysics Data System (ADS)

    Yoon, Seok-Hyun; Kim, Mi-Yang

    2016-06-01

    Temperature dependence of the dielectric nonlinearity was investigated for the BaTiO3 multilayer ceramic capacitor. The decrease in temperature caused a significant increase in the degree of dielectric nonlinearity. The Preisach analysis shows that such effect corresponds to a decrease in reversible and a significant increase in irreversible domain wall contribution to polarization. The magnitude of spontaneous polarization (PS) was increased with decreasing temperature. It can be associated with phase transition from pseudo-cubic to monoclinic and its resultant change in the polar direction, which was observed through transmission electron microscopy. These results demonstrate that the increase in PS with the decrease in temperature inhibits domain wall motion in low driving field as it is anticipated to increase the degree of intergranular constraints during domain wall motion. But it results in a more steep increase in the dielectric constants beyond the threshold field where domain wall motion can occur.

  8. Emerging Applications of Bedside 3D Printing in Plastic Surgery.

    PubMed

    Chae, Michael P; Rozen, Warren M; McMenamin, Paul G; Findlay, Michael W; Spychal, Robert T; Hunter-Smith, David J

    2015-01-01

    Modern imaging techniques are an essential component of preoperative planning in plastic and reconstructive surgery. However, conventional modalities, including three-dimensional (3D) reconstructions, are limited by their representation on 2D workstations. 3D printing, also known as rapid prototyping or additive manufacturing, was once the province of industry to fabricate models from a computer-aided design (CAD) in a layer-by-layer manner. The early adopters in clinical practice have embraced the medical imaging-guided 3D-printed biomodels for their ability to provide tactile feedback and a superior appreciation of visuospatial relationship between anatomical structures. With increasing accessibility, investigators are able to convert standard imaging data into a CAD file using various 3D reconstruction softwares and ultimately fabricate 3D models using 3D printing techniques, such as stereolithography, multijet modeling, selective laser sintering, binder jet technique, and fused deposition modeling. However, many clinicians have questioned whether the cost-to-benefit ratio justifies its ongoing use. The cost and size of 3D printers have rapidly decreased over the past decade in parallel with the expiration of key 3D printing patents. Significant improvements in clinical imaging and user-friendly 3D software have permitted computer-aided 3D modeling of anatomical structures and implants without outsourcing in many cases. These developments offer immense potential for the application of 3D printing at the bedside for a variety of clinical applications. In this review, existing uses of 3D printing in plastic surgery practice spanning the spectrum from templates for facial transplantation surgery through to the formation of bespoke craniofacial implants to optimize post-operative esthetics are described. Furthermore, we discuss the potential of 3D printing to become an essential office-based tool in plastic surgery to assist in preoperative planning, developing

  9. Emerging Applications of Bedside 3D Printing in Plastic Surgery

    PubMed Central

    Chae, Michael P.; Rozen, Warren M.; McMenamin, Paul G.; Findlay, Michael W.; Spychal, Robert T.; Hunter-Smith, David J.

    2015-01-01

    Modern imaging techniques are an essential component of preoperative planning in plastic and reconstructive surgery. However, conventional modalities, including three-dimensional (3D) reconstructions, are limited by their representation on 2D workstations. 3D printing, also known as rapid prototyping or additive manufacturing, was once the province of industry to fabricate models from a computer-aided design (CAD) in a layer-by-layer manner. The early adopters in clinical practice have embraced the medical imaging-guided 3D-printed biomodels for their ability to provide tactile feedback and a superior appreciation of visuospatial relationship between anatomical structures. With increasing accessibility, investigators are able to convert standard imaging data into a CAD file using various 3D reconstruction softwares and ultimately fabricate 3D models using 3D printing techniques, such as stereolithography, multijet modeling, selective laser sintering, binder jet technique, and fused deposition modeling. However, many clinicians have questioned whether the cost-to-benefit ratio justifies its ongoing use. The cost and size of 3D printers have rapidly decreased over the past decade in parallel with the expiration of key 3D printing patents. Significant improvements in clinical imaging and user-friendly 3D software have permitted computer-aided 3D modeling of anatomical structures and implants without outsourcing in many cases. These developments offer immense potential for the application of 3D printing at the bedside for a variety of clinical applications. In this review, existing uses of 3D printing in plastic surgery practice spanning the spectrum from templates for facial transplantation surgery through to the formation of bespoke craniofacial implants to optimize post-operative esthetics are described. Furthermore, we discuss the potential of 3D printing to become an essential office-based tool in plastic surgery to assist in preoperative planning, developing

  10. Array servo scanning micro EDM of 3D micro cavities

    NASA Astrophysics Data System (ADS)

    Tong, Hao; Li, Yong; Yi, Futing

    2010-12-01

    Micro electro discharge machining (Micro EDM) is a non-traditional processing technology with the special advantages of low set-up cost and few cutting force in machining any conductive materials regardless of their hardness. As well known, die-sinking EDM is unsuitable for machining the complex 3D micro cavity less than 1mm due to the high-priced fabrication of 3D microelectrode itself and its serous wear during EDM process. In our former study, a servo scanning 3D micro-EDM (3D SSMEDM) method was put forward, and our experiments showed it was available to fabricate complex 3D micro-cavities. In this study, in order to improve machining efficiency and consistency accuracy for array 3D micro-cavities, an array-servo-scanning 3D micro EDM (3D ASSMEDM) method is presented considering the complementary advantages of the 3D SSMEDM and the array micro electrodes with simple cross-section. During 3D ASSMEDM process, the array cavities designed by CAD / CAM system can be batch-manufactured by servo scanning layer by layer using array-rod-like micro tool electrodes, and the axial wear of the array electrodes is compensated in real time by keeping discharge gap. To verify the effectiveness of the 3D ASSMEDM, the array-triangle-micro cavities (side length 630 μm) are batch-manufactured on P-doped silicon by applying the array-micro-electrodes with square-cross-section fabricated by LIGA process. Our exploratory experiment shows that the 3D ASSMEDM provides a feasible approach for the batch-manufacture of 3D array-micro-cavities of conductive materials.

  11. Array servo scanning micro EDM of 3D micro cavities

    NASA Astrophysics Data System (ADS)

    Tong, Hao; Li, Yong; Yi, Futing

    2011-05-01

    Micro electro discharge machining (Micro EDM) is a non-traditional processing technology with the special advantages of low set-up cost and few cutting force in machining any conductive materials regardless of their hardness. As well known, die-sinking EDM is unsuitable for machining the complex 3D micro cavity less than 1mm due to the high-priced fabrication of 3D microelectrode itself and its serous wear during EDM process. In our former study, a servo scanning 3D micro-EDM (3D SSMEDM) method was put forward, and our experiments showed it was available to fabricate complex 3D micro-cavities. In this study, in order to improve machining efficiency and consistency accuracy for array 3D micro-cavities, an array-servo-scanning 3D micro EDM (3D ASSMEDM) method is presented considering the complementary advantages of the 3D SSMEDM and the array micro electrodes with simple cross-section. During 3D ASSMEDM process, the array cavities designed by CAD / CAM system can be batch-manufactured by servo scanning layer by layer using array-rod-like micro tool electrodes, and the axial wear of the array electrodes is compensated in real time by keeping discharge gap. To verify the effectiveness of the 3D ASSMEDM, the array-triangle-micro cavities (side length 630 μm) are batch-manufactured on P-doped silicon by applying the array-micro-electrodes with square-cross-section fabricated by LIGA process. Our exploratory experiment shows that the 3D ASSMEDM provides a feasible approach for the batch-manufacture of 3D array-micro-cavities of conductive materials.

  12. Solution-processed high-LUMO-level polymers in n-type organic field-effect transistors: a comparative study as a semiconducting layer, dielectric layer, or charge injection layer

    NASA Astrophysics Data System (ADS)

    Liu, Chuan; Xu, Yong; Liu, Xuying; Minari, Takeo; Sirringhaus, Henning; Noh, Yong-Young

    2015-04-01

    In solution-processed organic field-effect transistors (OFETs), the polymers with high level of lowest unoccupied molecular orbitals (LUMOs, > -3.5 eV) are especially susceptible to electron-trapping that causes low electron mobility and strong instability in successive operation. However, the role of high-LUMO-level polymers could be different depending on their locations relative to the semiconductor/insulator interface, or could even possibly benefit the device in some cases. We constructed unconventional polymer heterojunction n-type OFETs to control the location of the same polymer with a high LUMO level, to be in, under, or above the accumulation channel. We found that although the devices with the polymer in the channel suffer from dramatic instability, the same polymer causes much less instability when it acts as a dielectric modification layer or charge injection layer. Especially, it may even improve the device performance in the latter case. This result helps to improve our understanding of the electron-trapping and explore the value of these polymers in OFETs.

  13. Blending effect of 6,13-bis(triisopropylsilylethynyl) pentacene-graphene composite layers for flexible thin film transistors with a polymer gate dielectric.

    PubMed

    Basu, Sarbani; Adriyanto, Feri; Wang, Yeong-Her

    2014-02-28

    Solution processible poly(4-vinylphenol) is employed as a transistor dielectric material for low cost processing on flexible substrates at low temperatures. A 6,13-bis (triisopropylsilylethynyl) (TIPS) pentacene-graphene hybrid semiconductor is drop cast to fabricate bottom-gate and bottom-contact field-effect transistor devices on flexible and glass substrates under an ambient air environment. A few layers of graphene flakes increase the area in the conduction channel, and form bridge connections between the crystalline regions of the semiconductor layer which can change the surface morphology of TIPS pentacene films. The TIPS pentacene-graphene hybrid semiconductor-based organic thin film transistors (OTFTs) cross-linked with a poly(4-vinylphenol) gate dielectric exhibit an effective field-effect mobility of 0.076 cm(2) V(-1) s(-1) and a threshold voltage of -0.7 V at V(gs) = -40 V. By contrast, typical TIPS pentacene shows four times lower mobility of 0.019 cm(2) V(-1) s(-1) and a threshold voltage of 5 V. The graphene/TIPS pentacene hybrids presented in this paper can enhance the electrical characteristics of OTFTs due to their high crystallinity, uniform large-grain distribution, and effective reduction of crystal misorientation of the organic semiconductor layer, as confirmed by x-ray diffraction spectroscopy, atomic force microscopy, and optical microscopy studies. PMID:24492205

  14. Role of ultra thin pseudomorphic InP layer to improve the high-k dielectric/GaAs interface in realizing metal-oxide-semiconductor capacitor

    NASA Astrophysics Data System (ADS)

    Kundu, Souvik; Halder, Nripendra N.; Biswas, D.; Banerji, P.; Shripathi, T.; Chakraborty, S.

    2012-08-01

    In this article, we report GaAs metal-oxide-semiconductor (MOS) capacitors with a metal organic chemical vapor deposited ultrathin (1.5 nm) pseudomorphic InP interface passivation layer (IPL) and a thin (5 nm) ZrO2 high-k dielectric. Reduction of the surface states on InP passivated GaAs surfaces was observed from the photoluminescence study. The x-ray photoelectron spectra confirmed the dramatic reduction of GaAs native oxides (Ga-O and As-O) from the interface of ZrO2 and p-GaAs, implying that the Fermi level at the high-k/GaAs interface can be unpinned with good interface quality. As a result, very low values of interface trap density (1.1 × 1011 cm-2 eV-1) and hysteresis (8.21 mV) were observed. The same was done for directly deposited ZrO2 on GaAs surface to understand the efficacy of InP interface passivation layer on GaAs MOS devices. A systematic capacitance-voltage and current density-voltage studies were performed on bothAl/ZrO2/InP/p-GaAs and Al/ZrO2/p-GaAs structures. It was found that insertion of 1.5 nm InP ultrathin layer in-between ZrO2 and GaAs improves the essential parameters of GaAs MOS such as dielectric constant, frequency dispersion, leakage current, etc. The dielectric reliability has been studied with constant voltage stressing. A very small flatband voltage shift with stress time was observed in InP passivated GaAs MOS capacitors.

  15. Light shaping along 3D curves and particle manipulation

    NASA Astrophysics Data System (ADS)

    Rodrigo, José A.; Alieva, Tatiana

    2015-03-01

    We present a non-iterative holographic technique for efficient and versatile laser beam shaping along arbitrary 3D curves. Light beams with intensity shaped for several 3D curves: Tilted ring, Viviani's curve, Archimedean spiral, and trefoil-knotted curve have been experimentally generated and applied for optical trapping of micrometer-sized dielectric particles. The high intensity gradients and independent phase control prescribed along the curve make this kind of laser trap attractive for multiple particle manipulation and allow for forward and backward motion to the light source. Indeed, different configurations of tractor beam traps are experimentally demonstrated. This technique can also be applied for laser micro-machining.

  16. 3D coaxial out-of-plane metallic antennas for filtering and multi-spectral imaging in the infrared range

    PubMed Central

    Jacassi, Andrea; Bozzola, Angelo; Zilio, Pierfrancesco; Tantussi, Francesco; De Angelis, Francesco

    2016-01-01

    We fabricated and investigated a new configuration of 3D coaxial metallic antennas working in the infrared which combines the strong lateral light scattering of vertical plasmonic structures with the selective spectral transmission of 2D arrays of coaxial apertures. The coaxial structures are fabricated with a top-down method based on a template of hollow 3D antennas. Each antenna has a multilayer radial structure consisting of dielectric and metallic materials not achievable in a 2D configuration. A planar metallic layer is inserted normally to the antennas. The outer dielectric shell of the antenna defines a nanometric gap between the horizontal plane and the vertical walls. Thanks to this aperture, light can tunnel to the other side of the plane, and be transmitted to the far field in a set of resonances. These are investigated with finite-elements electromagnetic calculations and with Fourier-transform infrared spectroscopy measurements. The spectral position of the resonances can be tuned by changing the lattice period and/or the antenna length. Thanks to the strong scattering provided by the 3D geometry, the transmission peaks possess a high signal-to-noise ratio even when the illuminated area is less than 2 × 2 times the operation wavelength. This opens new possibilities for multispectral imaging in the IR with wavelength-scale spatial resolution. PMID:27345517

  17. 3D coaxial out-of-plane metallic antennas for filtering and multi-spectral imaging in the infrared range

    NASA Astrophysics Data System (ADS)

    Jacassi, Andrea; Bozzola, Angelo; Zilio, Pierfrancesco; Tantussi, Francesco; de Angelis, Francesco

    2016-06-01

    We fabricated and investigated a new configuration of 3D coaxial metallic antennas working in the infrared which combines the strong lateral light scattering of vertical plasmonic structures with the selective spectral transmission of 2D arrays of coaxial apertures. The coaxial structures are fabricated with a top-down method based on a template of hollow 3D antennas. Each antenna has a multilayer radial structure consisting of dielectric and metallic materials not achievable in a 2D configuration. A planar metallic layer is inserted normally to the antennas. The outer dielectric shell of the antenna defines a nanometric gap between the horizontal plane and the vertical walls. Thanks to this aperture, light can tunnel to the other side of the plane, and be transmitted to the far field in a set of resonances. These are investigated with finite-elements electromagnetic calculations and with Fourier-transform infrared spectroscopy measurements. The spectral position of the resonances can be tuned by changing the lattice period and/or the antenna length. Thanks to the strong scattering provided by the 3D geometry, the transmission peaks possess a high signal-to-noise ratio even when the illuminated area is less than 2 × 2 times the operation wavelength. This opens new possibilities for multispectral imaging in the IR with wavelength-scale spatial resolution.

  18. 3D coaxial out-of-plane metallic antennas for filtering and multi-spectral imaging in the infrared range.

    PubMed

    Jacassi, Andrea; Bozzola, Angelo; Zilio, Pierfrancesco; Tantussi, Francesco; De Angelis, Francesco

    2016-01-01

    We fabricated and investigated a new configuration of 3D coaxial metallic antennas working in the infrared which combines the strong lateral light scattering of vertical plasmonic structures with the selective spectral transmission of 2D arrays of coaxial apertures. The coaxial structures are fabricated with a top-down method based on a template of hollow 3D antennas. Each antenna has a multilayer radial structure consisting of dielectric and metallic materials not achievable in a 2D configuration. A planar metallic layer is inserted normally to the antennas. The outer dielectric shell of the antenna defines a nanometric gap between the horizontal plane and the vertical walls. Thanks to this aperture, light can tunnel to the other side of the plane, and be transmitted to the far field in a set of resonances. These are investigated with finite-elements electromagnetic calculations and with Fourier-transform infrared spectroscopy measurements. The spectral position of the resonances can be tuned by changing the lattice period and/or the antenna length. Thanks to the strong scattering provided by the 3D geometry, the transmission peaks possess a high signal-to-noise ratio even when the illuminated area is less than 2 × 2 times the operation wavelength. This opens new possibilities for multispectral imaging in the IR with wavelength-scale spatial resolution. PMID:27345517

  19. Capacitively induced high mobility two-dimensional electron gas in undoped Si /Si1-xGex heterostructures with atomic-layer-deposited dielectric

    NASA Astrophysics Data System (ADS)

    Lu, T. M.; Liu, J.; Kim, J.; Lai, K.; Tsui, D. C.; Xie, Y. H.

    2007-04-01

    The authors demonstrate that a high mobility two-dimensional electron gas can be capacitively induced in an undoped Si /Si1-xGex heterostructure using atomic-layer-deposited Al2O3 as the dielectric. The density is tuned up to 4.2×1011/cm2, limited by the gate leakage current. The mobility increases with the density rapidly and reaches 5.5×104cm2/Vs at the highest density. The observation of well developed quantum Hall states and two-dimensional metal-insulator transition shows that the devices are suitable for two-dimensional electron physics studies.

  20. Giant dielectric permittivity caused by carrier hopping in a layered cuprate Bi 2Ba 2Nd 1.6Ce 0.4Cu 2O 10+ δ

    NASA Astrophysics Data System (ADS)

    Xu, Xiaofeng; Cao, Guanghan; Jiao, Zhengkuan

    2004-12-01

    The ceramic sample of a layered cuprate Bi 2Ba 2Nd 1.6Ce 0.4Cu 2O 10+ δ, so-called Ba-based Bi-2222 compound was studied by the measurement of the temperature (80-300 K) and the frequency (20-10 6 Hz) dependence of the complex dielectric permittivity. The dielectric constant was measured as high as ˜1000 at 1 kHz and 300 K with relatively low dissipation factor. However, it decreases systematically with decreasing temperature or with increasing frequency due to the dipolar relaxation process. This thermally activated relaxation process plays a dominant role for the low frequency dielectric response. Furthermore, the frequency-dependent ac conductivity was found to obey the power law σ=Aω. The results were interpreted in terms of Pike's model of hopping transport of localized charge carriers which yields explicitly the ω behavior and the temperature dependence of s. And we calculated the ionization energy of localized carriers W=0.35 eV for the present sample.

  1. Three wafer stacking for 3D integration.

    SciTech Connect

    Greth, K. Douglas; Ford, Christine L.; Lantz, Jeffrey W.; Shinde, Subhash L.; Timon, Robert P.; Bauer, Todd M.; Hetherington, Dale Laird; Sanchez, Carlos Anthony

    2011-11-01

    Vertical wafer stacking will enable a wide variety of new system architectures by enabling the integration of dissimilar technologies in one small form factor package. With this LDRD, we explored the combination of processes and integration techniques required to achieve stacking of three or more layers. The specific topics that we investigated include design and layout of a reticle set for use as a process development vehicle, through silicon via formation, bonding media, wafer thinning, dielectric deposition for via isolation on the wafer backside, and pad formation.

  2. YouDash3D: exploring stereoscopic 3D gaming for 3D movie theaters

    NASA Astrophysics Data System (ADS)

    Schild, Jonas; Seele, Sven; Masuch, Maic

    2012-03-01

    Along with the success of the digitally revived stereoscopic cinema, events beyond 3D movies become attractive for movie theater operators, i.e. interactive 3D games. In this paper, we present a case that explores possible challenges and solutions for interactive 3D games to be played by a movie theater audience. We analyze the setting and showcase current issues related to lighting and interaction. Our second focus is to provide gameplay mechanics that make special use of stereoscopy, especially depth-based game design. Based on these results, we present YouDash3D, a game prototype that explores public stereoscopic gameplay in a reduced kiosk setup. It features live 3D HD video stream of a professional stereo camera rig rendered in a real-time game scene. We use the effect to place the stereoscopic effigies of players into the digital game. The game showcases how stereoscopic vision can provide for a novel depth-based game mechanic. Projected trigger zones and distributed clusters of the audience video allow for easy adaptation to larger audiences and 3D movie theater gaming.

  3. Enhancing the coherence of 3D qubits suitable for multi-qubit experiments

    NASA Astrophysics Data System (ADS)

    Abdo, Baleegh; McClure, Douglas; Paik, Hanhee; Sandberg, Martin; Gambetta, Jay; Dial, Oliver

    2015-03-01

    Superconducting qubits coupled to 3D cavities have several advantages over qubits coupled to planar cavities on the same chip, e.g., 1) they can be individually designed, tested, and integrated, 2) they exhibit better microwave hygiene than their 2D counterpart, and 3) they possess higher coherence times, in part because they have reduced participation ratios for surface dielectric layers that can be lossy. However, in order to implement the surface code using a multi-qubit system, 3D qubits and their corresponding microwave cavities have to meet several competing requirements in addition to preserving long coherence, such as large coupling of the 3D qubit to two adjacent microwave resonators, sufficient coupling to other qubits, and large microwave isolation between different cavities. Finding a qubit design that balances all of these requirements has proved challenging so far. In this work, we apply a combination of simulations and experiments to investigate a variety of loss mechanisms that are particularly relevant for multi-qubit systems. Based on this learning, we identify changes in the design and materials of these systems that can lead to enhancement of their coherence times. We acknowledge support from IARPA under Contract W911NF-10-1-0324.

  4. 3D Technology for intelligent trackers

    SciTech Connect

    Lipton, Ronald; /Fermilab

    2010-09-01

    At Super-LHC luminosity it is expected that the standard suite of level 1 triggers for CMS will saturate. Information from the tracker will be needed to reduce trigger rates to satisfy the level 1 bandwidth. Tracking trigger modules which correlate information from closely-spaced sensor layers to form an on-detector momentum filter are being developed by several groups. We report on a trigger module design which utilizes three dimensional integrated circuit technology incorporating chips which are connected both to the top and bottom sensor, providing the ability to filter information locally. A demonstration chip, the VICTR, has been submitted to the Chartered/Tezzaron two-tier 3D run coordinated by Fermilab. We report on the 3D design concept, the status of the VICTR chip and associated sensor integration utilizing oxide bonding.

  5. Remote 3D Medical Consultation

    NASA Astrophysics Data System (ADS)

    Welch, Greg; Sonnenwald, Diane H.; Fuchs, Henry; Cairns, Bruce; Mayer-Patel, Ketan; Yang, Ruigang; State, Andrei; Towles, Herman; Ilie, Adrian; Krishnan, Srinivas; Söderholm, Hanna M.

    Two-dimensional (2D) video-based telemedical consultation has been explored widely in the past 15-20 years. Two issues that seem to arise in most relevant case studies are the difficulty associated with obtaining the desired 2D camera views, and poor depth perception. To address these problems we are exploring the use of a small array of cameras to synthesize a spatially continuous range of dynamic three-dimensional (3D) views of a remote environment and events. The 3D views can be sent across wired or wireless networks to remote viewers with fixed displays or mobile devices such as a personal digital assistant (PDA). The viewpoints could be specified manually or automatically via user head or PDA tracking, giving the remote viewer virtual head- or hand-slaved (PDA-based) remote cameras for mono or stereo viewing. We call this idea remote 3D medical consultation (3DMC). In this article we motivate and explain the vision for 3D medical consultation; we describe the relevant computer vision/graphics, display, and networking research; we present a proof-of-concept prototype system; and we present some early experimental results supporting the general hypothesis that 3D remote medical consultation could offer benefits over conventional 2D televideo.

  6. Speaking Volumes About 3-D

    NASA Technical Reports Server (NTRS)

    2002-01-01

    In 1999, Genex submitted a proposal to Stennis Space Center for a volumetric 3-D display technique that would provide multiple users with a 360-degree perspective to simultaneously view and analyze 3-D data. The futuristic capabilities of the VolumeViewer(R) have offered tremendous benefits to commercial users in the fields of medicine and surgery, air traffic control, pilot training and education, computer-aided design/computer-aided manufacturing, and military/battlefield management. The technology has also helped NASA to better analyze and assess the various data collected by its satellite and spacecraft sensors. Genex capitalized on its success with Stennis by introducing two separate products to the commercial market that incorporate key elements of the 3-D display technology designed under an SBIR contract. The company Rainbow 3D(R) imaging camera is a novel, three-dimensional surface profile measurement system that can obtain a full-frame 3-D image in less than 1 second. The third product is the 360-degree OmniEye(R) video system. Ideal for intrusion detection, surveillance, and situation management, this unique camera system offers a continuous, panoramic view of a scene in real time.

  7. Properties of Ultrathin Al2O3-TiO2 Nanolaminate Films for Gate Dielectric Applications Deposited by Plasma-Assisted Atomic Layer Deposition

    NASA Astrophysics Data System (ADS)

    Garces, Nelson; Meyer, David; Nepal, Neeraj; Wheeler, Virginia; Eddy, Charles

    2012-02-01

    High permittivity dielectrics such as Al2O3, HfO2, Ta2O5, TiO2, etc., are an essential component of aggressively-scaled III-V and graphene field effect transistors (FETs) where insulators are necessary to reduce gate leakage current while maintaining high gate capacitance and charge control of the channel. Atomic layer deposition (ALD) has the capability to deposit hybrid films, or nanolaminates, of two or more dielectrics that have unique properties. Thin [Al2O3+TiO2] nanolaminates with varying TiO2 and Al2O3 content were deposited on n-Si substrates at ˜225-300 C using ALD. A nanolaminate is composed of bilayers, defined as the sum of (x)Al2O3 and (y)TiO2, where x, and y indicate the number of times a component monolayer is repeated. While the overall thickness of the dielectric was held at ˜ 17-20 nm, the relative ratio of Al2O3 to TiO2 in the bilayer stack was varied to evaluate changes in the material properties and electrical performance of the oxides. C-V and I-V measurements on various [(x)TiO2+(y)Al2O3] MOS capacitors were taken. The high-TiO2-content films show limited evidence of oxide charge trapping and relatively large dielectric constants (κ˜15), whereas the high-Al2O3-content films offer a larger optical bandgap and improved suppression of leakage current. We will discuss the properties of very thin nanolaminates and their possible use as gate oxides. Morphological, electrical, and XPS composition assessments will be presented.

  8. USM3D Predictions of Supersonic Nozzle Flow

    NASA Technical Reports Server (NTRS)

    Carter, Melissa B.; Elmiligui, Alaa A.; Campbell, Richard L.; Nayani, Sudheer N.

    2014-01-01

    This study focused on the NASA Tetrahedral Unstructured Software System CFD code (USM3D) capability to predict supersonic plume flow. Previous studies, published in 2004 and 2009, investigated USM3D's results versus historical experimental data. This current study continued that comparison however focusing on the use of the volume souring to capture the shear layers and internal shock structure of the plume. This study was conducted using two benchmark axisymmetric supersonic jet experimental data sets. The study showed that with the use of volume sourcing, USM3D was able to capture and model a jet plume's shear layer and internal shock structure.

  9. 3D-Printed Microfluidics.

    PubMed

    Au, Anthony K; Huynh, Wilson; Horowitz, Lisa F; Folch, Albert

    2016-03-14

    The advent of soft lithography allowed for an unprecedented expansion in the field of microfluidics. However, the vast majority of PDMS microfluidic devices are still made with extensive manual labor, are tethered to bulky control systems, and have cumbersome user interfaces, which all render commercialization difficult. On the other hand, 3D printing has begun to embrace the range of sizes and materials that appeal to the developers of microfluidic devices. Prior to fabrication, a design is digitally built as a detailed 3D CAD file. The design can be assembled in modules by remotely collaborating teams, and its mechanical and fluidic behavior can be simulated using finite-element modeling. As structures are created by adding materials without the need for etching or dissolution, processing is environmentally friendly and economically efficient. We predict that in the next few years, 3D printing will replace most PDMS and plastic molding techniques in academia. PMID:26854878

  10. Sequential lateral solidification of silicon thin films on low-k dielectrics for low temperature integration

    NASA Astrophysics Data System (ADS)

    Carta, Fabio; Gates, Stephen M.; Limanov, Alexander B.; Hlaing, Htay; Im, James S.; Edelstein, Daniel C.; Kymissis, Ioannis

    2014-12-01

    We present the excimer laser crystallization of amorphous silicon on a low dielectric constant (low-k) insulator for very large scale integration monolithic 3D integration and demonstrate that low dielectric constant materials are suitable substrates for 3D integration through laser crystallization of silicon thin films. We crystallized 100 nm amorphous silicon on top of SiO2 and SiCOH (low-k) dielectrics, at different material thicknesses (1 μm, 0.75 μm, and 0.5 μm). The amorphous silicon crystallization on low-k dielectric requires 35% less laser energy than on an SiO2 dielectric. This difference is related to the thermal conductivity of the two materials, in agreement with one dimensional simulations of the crystallization process. We analyzed the morphology of the material through defect-enhanced microscopy, Raman spectroscopy, and X-ray diffraction analysis. SEM micrographs show that polycrystalline silicon is characterized by micron-long grains with an average width of 543 nm for the SiO2 sample and 570 nm for the low-k samples. Comparison of the Raman spectra does not show any major difference in film quality for the two different dielectrics, and polycrystalline silicon peaks are closely placed around 517 cm-1. From X-ray diffraction analysis, the material crystallized on SiO2 shows a preferential (111) crystal orientation. In the SiCOH case, the 111 peak strength decreases dramatically and samples do not show preferential crystal orientation. A 1D finite element method simulation of the crystallization process on a back end of line structure shows that copper (Cu) damascene interconnects reach a temperature of 70 °C or lower with a 0.5 μm dielectric layer between the Cu and the molten Si layer, a favorable condition for monolithic 3D integration.

  11. 3D Computations and Experiments

    SciTech Connect

    Couch, R; Faux, D; Goto, D; Nikkel, D

    2004-04-05

    This project consists of two activities. Task A, Simulations and Measurements, combines all the material model development and associated numerical work with the materials-oriented experimental activities. The goal of this effort is to provide an improved understanding of dynamic material properties and to provide accurate numerical representations of those properties for use in analysis codes. Task B, ALE3D Development, involves general development activities in the ALE3D code with the focus of improving simulation capabilities for problems of mutual interest to DoD and DOE. Emphasis is on problems involving multi-phase flow, blast loading of structures and system safety/vulnerability studies.

  12. 3D Computations and Experiments

    SciTech Connect

    Couch, R; Faux, D; Goto, D; Nikkel, D

    2003-05-12

    This project is in its first full year after the combining of two previously funded projects: ''3D Code Development'' and ''Dynamic Material Properties''. The motivation behind this move was to emphasize and strengthen the ties between the experimental work and the computational model development in the materials area. The next year's activities will indicate the merging of the two efforts. The current activity is structured in two tasks. Task A, ''Simulations and Measurements'', combines all the material model development and associated numerical work with the materials-oriented experimental activities. Task B, ''ALE3D Development'', is a continuation of the non-materials related activities from the previous project.

  13. Atomic layer deposition of crystalline SrHfO{sub 3} directly on Ge (001) for high-k dielectric applications

    SciTech Connect

    McDaniel, Martin D.; Ngo, Thong Q.; Ekerdt, John G.; Hu, Chengqing; Jiang, Aiting; Yu, Edward T.; Lu, Sirong; Smith, David J.; Posadas, Agham; Demkov, Alexander A.

    2015-02-07

    The current work explores the crystalline perovskite oxide, strontium hafnate, as a potential high-k gate dielectric for Ge-based transistors. SrHfO{sub 3} (SHO) is grown directly on Ge by atomic layer deposition and becomes crystalline with epitaxial registry after post-deposition vacuum annealing at ∼700 °C for 5 min. The 2 × 1 reconstructed, clean Ge (001) surface is a necessary template to achieve crystalline films upon annealing. The SHO films exhibit excellent crystallinity, as shown by x-ray diffraction and transmission electron microscopy. The SHO films have favorable electronic properties for consideration as a high-k gate dielectric on Ge, with satisfactory band offsets (>2 eV), low leakage current (<10{sup −5} A/cm{sup 2} at an applied field of 1 MV/cm) at an equivalent oxide thickness of 1 nm, and a reasonable dielectric constant (k ∼ 18). The interface trap density (D{sub it}) is estimated to be as low as ∼2 × 10{sup 12 }cm{sup −2 }eV{sup −1} under the current growth and anneal conditions. Some interfacial reaction is observed between SHO and Ge at temperatures above ∼650 °C, which may contribute to increased D{sub it} value. This study confirms the potential for crystalline oxides grown directly on Ge by atomic layer deposition for advanced electronic applications.

  14. SNL3dFace

    2007-07-20

    This software distribution contains MATLAB and C++ code to enable identity verification using 3D images that may or may not contain a texture component. The code is organized to support system performance testing and system capability demonstration through the proper configuration of the available user interface. Using specific algorithm parameters the face recognition system has been demonstrated to achieve a 96.6% verification rate (Pd) at 0.001 false alarm rate. The system computes robust facial featuresmore » of a 3D normalized face using Principal Component Analysis (PCA) and Fisher Linear Discriminant Analysis (FLDA). A 3D normalized face is obtained by alighning each face, represented by a set of XYZ coordinated, to a scaled reference face using the Iterative Closest Point (ICP) algorithm. The scaled reference face is then deformed to the input face using an iterative framework with parameters that control the deformed surface regulation an rate of deformation. A variety of options are available to control the information that is encoded by the PCA. Such options include the XYZ coordinates, the difference of each XYZ coordinates from the reference, the Z coordinate, the intensity/texture values, etc. In addition to PCA/FLDA feature projection this software supports feature matching to obtain similarity matrices for performance analysis. In addition, this software supports visualization of the STL, MRD, 2D normalized, and PCA synthetic representations in a 3D environment.« less

  15. Making Inexpensive 3-D Models

    ERIC Educational Resources Information Center

    Manos, Harry

    2016-01-01

    Visual aids are important to student learning, and they help make the teacher's job easier. Keeping with the "TPT" theme of "The Art, Craft, and Science of Physics Teaching," the purpose of this article is to show how teachers, lacking equipment and funds, can construct a durable 3-D model reference frame and a model gravity…

  16. SNL3dFace

    SciTech Connect

    Russ, Trina; Koch, Mark; Koudelka, Melissa; Peters, Ralph; Little, Charles; Boehnen, Chris; Peters, Tanya

    2007-07-20

    This software distribution contains MATLAB and C++ code to enable identity verification using 3D images that may or may not contain a texture component. The code is organized to support system performance testing and system capability demonstration through the proper configuration of the available user interface. Using specific algorithm parameters the face recognition system has been demonstrated to achieve a 96.6% verification rate (Pd) at 0.001 false alarm rate. The system computes robust facial features of a 3D normalized face using Principal Component Analysis (PCA) and Fisher Linear Discriminant Analysis (FLDA). A 3D normalized face is obtained by alighning each face, represented by a set of XYZ coordinated, to a scaled reference face using the Iterative Closest Point (ICP) algorithm. The scaled reference face is then deformed to the input face using an iterative framework with parameters that control the deformed surface regulation an rate of deformation. A variety of options are available to control the information that is encoded by the PCA. Such options include the XYZ coordinates, the difference of each XYZ coordinates from the reference, the Z coordinate, the intensity/texture values, etc. In addition to PCA/FLDA feature projection this software supports feature matching to obtain similarity matrices for performance analysis. In addition, this software supports visualization of the STL, MRD, 2D normalized, and PCA synthetic representations in a 3D environment.

  17. 3D Printing: Exploring Capabilities

    ERIC Educational Resources Information Center

    Samuels, Kyle; Flowers, Jim

    2015-01-01

    As 3D printers become more affordable, schools are using them in increasing numbers. They fit well with the emphasis on product design in technology and engineering education, allowing students to create high-fidelity physical models to see and test different iterations in their product designs. They may also help students to "think in three…

  18. Effect of Ca incorporation on the dielectric nonlinear behavior of (Ba, Ca)TiO3 multi layer ceramic capacitors

    NASA Astrophysics Data System (ADS)

    Yoon, Seok-Hyun; Park, Yunjung; Kim, Chang-Hoon; Kim, Doo-Young

    2014-12-01

    The difference in the dielectric nonlinearity was investigated by contrasting BaTiO3 and (Ba0.925Ca0.075)TiO3 multilayer ceramic capacitors utilizing the first order reversal curve (FORC) distribution based on the Preisach model. Ca incorporation caused a decrease of the dielectric constants in the low field but little differences in the high field region resulting in a steep ac field dependence, which became more significant with the decrease of temperature. Such behavior can be correlated with a decrease of the reversible and an increase of the irreversible FORC distribution near origin by Ca incorporation. These results suggest that Ca incorporation, which is known to cause the asymmetric off-center displacement at Ba-site, has the role of weakly pinning centers that increase the portion of irreversible domain walls that are immobile at low field but can contribute to polarization beyond a threshold field.

  19. 3D Band Diagram and Photoexcitation of 2D–3D Semiconductor Heterojunctions

    DOE PAGESBeta

    Li, Bo; Shi, Gang; Lei, Sidong; He, Yongmin; Gao, Weilu; Gong, Yongji; Ye, Gonglan; Zhou, Wu; Keyshar, Kunttal; Hao, Ji; et al

    2015-08-17

    The emergence of a rich variety of two-dimensional (2D) layered semiconductor materials has enabled the creation of atomically thin heterojunction devices. Junctions between atomically thin 2D layers and 3D bulk semiconductors can lead to junctions that are fundamentally electronically different from the covalently bonded conventional semiconductor junctions. In this paper, we propose a new 3D band diagram for the heterojunction formed between n-type monolayer MoS2 and p-type Si, in which the conduction and valence band-edges of the MoS2 monolayer are drawn for both stacked and in-plane directions. This new band diagram helps visualize the flow of charge carriers inside themore » device in a 3D manner. Our detailed wavelength-dependent photocurrent measurements fully support the diagrams and unambiguously show that the band alignment is type I for this 2D-3D heterojunction. Photogenerated electron–hole pairs in the atomically thin monolayer are separated and driven by an external bias and control the “on/off” states of the junction photodetector device. Finally, two photoresponse regimes with fast and slow relaxation are also revealed in time-resolved photocurrent measurements, suggesting the important role played by charge trap states.« less

  20. 3D Band Diagram and Photoexcitation of 2D–3D Semiconductor Heterojunctions

    SciTech Connect

    Li, Bo; Shi, Gang; Lei, Sidong; He, Yongmin; Gao, Weilu; Gong, Yongji; Ye, Gonglan; Zhou, Wu; Keyshar, Kunttal; Hao, Ji; Dong, Pei; Ge, Liehui; Lou, Jun; Kono, Junichiro; Vajtai, Robert; Ajayan, Pulickel M.

    2015-08-17

    The emergence of a rich variety of two-dimensional (2D) layered semiconductor materials has enabled the creation of atomically thin heterojunction devices. Junctions between atomically thin 2D layers and 3D bulk semiconductors can lead to junctions that are fundamentally electronically different from the covalently bonded conventional semiconductor junctions. In this paper, we propose a new 3D band diagram for the heterojunction formed between n-type monolayer MoS2 and p-type Si, in which the conduction and valence band-edges of the MoS2 monolayer are drawn for both stacked and in-plane directions. This new band diagram helps visualize the flow of charge carriers inside the device in a 3D manner. Our detailed wavelength-dependent photocurrent measurements fully support the diagrams and unambiguously show that the band alignment is type I for this 2D-3D heterojunction. Photogenerated electron–hole pairs in the atomically thin monolayer are separated and driven by an external bias and control the “on/off” states of the junction photodetector device. Finally, two photoresponse regimes with fast and slow relaxation are also revealed in time-resolved photocurrent measurements, suggesting the important role played by charge trap states.