Science.gov

Sample records for 3rd stage lpt

  1. Rocketdyne - J-2 Saturn V 2nd and 3rd Stage Engine. Chapter 2, Appendix D

    NASA Technical Reports Server (NTRS)

    Coffman, Paul

    2009-01-01

    The J-2 engine was unique in many respects. Technology was not nearly as well-developed in oxygen/hydrogen engines at the start of the J-2 project. As a result, it experienced a number of "teething" problems. It was used in two stages on the Saturn V vehicle in the Apollo Program, as well as on the later Skylab and Apollo/Soyuz programs. In the Apollo Program, it was used on the S-II stage, which was the second stage of the Saturn V vehicle. There were five J-2 engines at the back end of the S-II Stage. In the S-IV-B stage, it was a single engine, but that single engine had to restart. The Apollo mission called for the entire vehicle to reach orbital velocity in low Earth orbit after the first firing of the Saturn-IV-B stage and, subsequently, to fire a second time to go on to the moon. The engine had to be man-rated (worthy of transporting humans). It had to have a high thrust rate and performance associated with oxygen/hydrogen engines, although there were some compromises there. It had to gimbal for thrust vector control. It was an open-cycle gas generator engine delivering up to 230,000 pounds of thrust.

  2. In vitro effects of three woody plant and sainfoin extracts on 3rd-stage larvae and adult worms of three gastrointestinal nematodes.

    PubMed

    Paolini, V; Fouraste, I; Hoste, H

    2004-07-01

    Most studies on the effects of tanniferous plants on nematodes have examined forages but have neglected the woody plants. Therefore, in vitro effects of extracts from 3 woody plants (Rubus fructicosus, Quercus robur, Corylus avellana) have been tested on trichostrongyles and compared to sainfoin, a legume forage. Because some in vivo results indicated that the effects of tannins differed depending on the parasitic species and/or stages, the effects were measured on 3rd-stage larvae (L3) and adult worms of Teladorsagia circumcincta, Haemonchlus contortus and Trichostrongylus colubriformis. The effects of plant extracts varied according to the plant sources, the parasite species and stages. For the woody plants, significant inhibitory effects were obtained on both stages of abomasal species. Results for T. colubriformis were more variable. Effects of sainfoin extracts were significant on T. colubriformis and H. contortus L3, and on abomasal adult worms. In order to assess the implications of tannins, polyethylene glycol (PEG), an inhibitor of tannins, was added to hazel tree, oak and sainfoin extracts. Without PEG, significant inhibitory effects on L3 and adult worms were confirmed. After addition of PEG, the larval migration and motility of adult worms were restored in most cases. These results confirm variations in effects depending on factors related to plants or parasites and suggest that tannins are partly responsible for the effects. PMID:15267113

  3. Stages of Geoinformation Evolution Related to the Territories Described in the Bible - from the 3Rd Millennium B.C. to Modern Times

    NASA Astrophysics Data System (ADS)

    Linsenbarth, Adam

    2012-09-01

    The paper presents consecutive stages of the evolution of geoinformation related to the territories of the events described in the Bible. Two geoinformation sources are presented: the Bible and non-Bible sources. In the Bible there is much, often some highly detailed information regarding terrain topography. The oldest non-Bible sources are incorporated in the ancient documents, which were discovered in Egypt and Mesopotamia. Some of them are related to the 3rd millen- nium B.C. The further stages are related to the onomasticons and itineraries written by travellers and pilgrims to the Holy Land. The most famous onomasticons include: onomasticons prepared by bishop Eusebius from Caesarea and those pre- pared by St. Jerome. One of the oldest maps of Palestine's territory is the so-called mosaic map of Madaba dated to 565. In the 15th century several Bible maps were edited. The most rapid evolution occurred in the 16th and 17* centuries, when the world famous cartographers such as Mercator and Ortelius edited several maps of Palestine's territory. Cartographers from several European countries edited more than 6,000 maps presenting the Biblical territories and Biblical events. Modem maps, based on detailed topographical surveys, were edited m the second half of the 19* and 20th centuries. W artykule przedstawiono kolejne etapy rozwoju geoinformacji dotyczącej terenówr biblijnych. Omówiono dwa źródła informacji, a mianowicie geoinformacje biblijne i pozabiblijne. W tekstach biblijnych można znaleźć wiele, często bardzo detalicznych informacji topograficznych. Najstarsze źródła pozabiblijne, to starożytne dokumenty odnalezione na terenach Egiptu i Mezopotamii. Niektóre z nich pochodzą z trzeciego milenium przed Chr. Kolejnym etapem geoinformacji były onomastikony oraz dzienniki podróży pisane przez podróżników i pielgrzymów do Ziemi Świętej. Do najbardziej znanych należy onomastikon sporządzony przez biskupa Euzebiusza z Cezarei oraz

  4. Accelerated life test of the USDOE OC-OTEC experimental system refurbished with magnetic bearings for the 3rd stage vacuum compressor. Final report

    SciTech Connect

    Vega, L.A.

    1997-04-01

    This report documents the accelerated life test (time-to-failure) performed, at the request of DOE, to evaluate the viability of the magnetic bearing system installed in the stage 3 vacuum pump. To this effect the plant was successfully operated for over 500 hours during the period September-November 1996. The first part of this report discusses system performance by deriving subsystem and system performance parameters from a typical record. This is followed by the discussion of the life tests. The instrumentation used to estimate the performance parameters given here is depicted. The third stage pump was operated for 535 hours without incident. It is concluded that magnetic bearings are the preferable choice for the OC-OTEC centrifugal vacuum pumps.

  5. Interpreting Borderline BeLPT Results

    PubMed Central

    Middleton, D.C.; Mayer, A.S.; Lewin, M.D.; Mroz, M.M.; Maier, L.A.

    2015-01-01

    Background The beryllium lymphocyte proliferation test (BeLPT) identifies persons sensitized to beryllium (BeS) and thus at risk for chronic beryllium disease (CBD). BeLPT test results are abnormal (AB), borderline (BL), or normal (NL). This manuscript addresses the predictive value and interpretation of BL BeLPT results. Methods The various three-result combinations that meet or exceed a nominal referral criteria of 1 AB + 1 BL are assessed with probability modeling and compared. Results At 2% prevalence, the three-result combinations that meet or exceed this referral criteria and associated probabilities of BeS are: (a) 1 AB + 1 BL + 1 NL (72%); (b) 3 BL (91%); (c) 2 AB + 1 NL (95%); (d) 1 AB + 2 BL (99%); (e) 2 AB + 1 BL (100%); and (f) 3 AB (100%). Conclusion These results suggest that BL results are meaningful and that three BL results predict BeS across a broad range of population prevalences. An analysis of longitudinal BeLPT results and clinical findings from an actual surveillance program is warranted to confirm the model’s predictions. PMID:20957676

  6. 2nd & 3rd Generation Vehicle Subsystems

    NASA Technical Reports Server (NTRS)

    2000-01-01

    This paper contains viewgraph presentation on the "2nd & 3rd Generation Vehicle Subsystems" project. The objective behind this project is to design, develop and test advanced avionics, power systems, power control and distribution components and subsystems for insertion into a highly reliable and low-cost system for a Reusable Launch Vehicles (RLV). The project is divided into two sections: 3rd Generation Vehicle Subsystems and 2nd Generation Vehicle Subsystems. The following topics are discussed under the first section, 3rd Generation Vehicle Subsystems: supporting the NASA RLV program; high-performance guidance & control adaptation for future RLVs; Evolvable Hardware (EHW) for 3rd generation avionics description; Scaleable, Fault-tolerant Intelligent Network or X(trans)ducers (SFINIX); advance electric actuation devices and subsystem technology; hybrid power sources and regeneration technology for electric actuators; and intelligent internal thermal control. Topics discussed in the 2nd Generation Vehicle Subsystems program include: design, development and test of a robust, low-maintenance avionics with no active cooling requirements and autonomous rendezvous and docking systems; design and development of a low maintenance, high reliability, intelligent power systems (fuel cells and battery); and design of a low cost, low maintenance high horsepower actuation systems (actuators).

  7. BACODINE/3rd Interplanetary Network burst localization

    SciTech Connect

    Hurley, K.; Barthelmy, S.; Butterworth, P.; Cline, T.; Sommer, M.; Boer, M.; Niel, M.; Kouveliotou, C.; Fishman, G.; Meegan, C.

    1996-08-01

    Even with only two widely separated spacecraft (Ulysses and GRO), 3rd Interplanetary Network (IPN) localizations can reduce the areas of BATSE error circles by two orders of magnitude. Therefore it is useful to disseminate them as quickly as possible following BATSE bursts. We have implemented a system which transmits the light curves of BACODINE/BATSE bursts directly by e-mail to UC Berkeley immediately after detection. An automatic e-mail parser at Berkeley watches for these notices, determines the Ulysses crossing time window, and initiates a search for the burst data on the JPL computer as they are received. In ideal cases, it is possible to retrieve the Ulysses data within a few hours of a burst, generate an annulus of arrival directions, and e-mail it out to the astronomical community by local nightfall. Human operators remain in this loop, but we are developing a fully automated routine which should remove them, at least for intense events, and reduce turn-around times to an absolute minimum. We explain the current operations, the data types used, and the speed/accuracy tradeoffs.

  8. 77 FR 1043 - Airworthiness Directives; Honeywell International Inc. Turbofan Engines

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-09

    ... 12866, (2) Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034.... During LPT rotor acceleration, these blades may contact and damage the 3rd stage LPT (LPT3) nozzle seal.... During LPT rotor acceleration, these blades may contact and damage the LPT3 nozzle seal carrier,...

  9. The Lack of the Essential LptC Protein in the Trans-Envelope Lipopolysaccharide Transport Machine Is Circumvented by Suppressor Mutations in LptF, an Inner Membrane Component of the Escherichia coli Transporter

    PubMed Central

    Benedet, Mattia; Falchi, Federica A.; Puccio, Simone; Di Benedetto, Cristiano; Peano, Clelia; Polissi, Alessandra

    2016-01-01

    The lipopolysaccharide (LPS) transport (Lpt) system is responsible for transferring LPS from the periplasmic surface of the inner membrane (IM) to the outer leaflet of the outer membrane (OM), where it plays a crucial role in OM selective permeability. In E. coli seven essential proteins are assembled in an Lpt trans-envelope complex, which is conserved in γ-Proteobacteria. LptBFG constitute the IM ABC transporter, LptDE form the OM translocon for final LPS delivery, whereas LptC, an IM-anchored protein with a periplasmic domain, interacts with the IM ABC transporter, the periplasmic protein LptA, and LPS. Although essential, LptC can tolerate several mutations and its role in LPS transport is unclear. To get insights into the functional role of LptC in the Lpt machine we searched for viable mutants lacking LptC by applying a strong double selection for lptC deletion mutants. Genome sequencing of viable ΔlptC mutants revealed single amino acid substitutions at a unique position in the predicted large periplasmic domain of the IM component LptF (LptFSupC). In complementation tests, lptFSupC mutants suppress lethality of both ΔlptC and lptC conditional expression mutants. Our data show that mutations in a specific residue of the predicted LptF periplasmic domain can compensate the lack of the essential protein LptC, implicate such LptF domain in the formation of the periplasmic bridge between the IM and OM complexes, and suggest that LptC may have evolved to improve the performance of an ancestral six-component Lpt machine. PMID:27529623

  10. LPT. EBOR reactor vessel in TAN 646. Pressure vessel head ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. EBOR reactor vessel in TAN 646. Pressure vessel head being installed in vault. Refueling port extension (right) and control rod nozzles (center). Camera facing northwest. Photographer: Comiskey. Date: January 20, 1965. INEEL negative no. 65-241 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  11. Numerical study of improving aerodynamic performance of low solidity LPT cascade through increasing trailing edge thickness

    NASA Astrophysics Data System (ADS)

    Li, Chao; Yan, Peigang; Wang, Xiangfeng; Han, Wanjin; Wang, Qingchao

    2016-08-01

    This paper presents a new idea to reduce the solidity of low-pressure turbine (LPT) blade cascades, while remain the structural integrity of LPT blade. Aerodynamic performance of a low solidity LPT cascade was improved by increasing blade trailing edge thickness (TET). The solidity of the LPT cascade blade can be reduced by about 12.5% through increasing the TET of the blade without a significant drop in energy efficiency. For the low solidity LPT cascade, increasing the TET can decrease energy loss by 23.30% and increase the flow turning angle by 1.86% for Reynolds number (Re) of 25,000 and freestream turbulence intensities (FSTI) of 2.35%. The flow control mechanism governing behavior around the trailing edge of an LPT cascade is also presented. The results show that appropriate TET is important for the optimal design of high-lift load LPT blade cascades.

  12. Solution Structure and Dynamics of LptE from Pseudomonas aeruginosa.

    PubMed

    Moehle, Kerstin; Kocherla, Harsha; Bacsa, Bernadett; Jurt, Simon; Zerbe, Katja; Robinson, John A; Zerbe, Oliver

    2016-05-31

    LptE is an outer membrane (OM) lipoprotein found in Gram-negative bacteria, where it forms a complex with the β-barrel lipopolysaccharide (LPS) transporter LptD. The LptD/E complex plays a key role in OM biogenesis, by translocating newly synthesized LPS molecules from the periplasm into the external leaflet of the asymmetric OM during cell growth. The LptD/E complex in Pseudomonas aeruginosa (Pa) is a target for macrocyclic β-hairpin-shaped peptidomimetic antibiotics, which inhibit the transport of LPS to the cell surface. So far, the three-dimensional structure of the Pa LptD/E complex and the mode of interaction with these antibiotics are unknown. Here, we report the solution structure of a Pa LptE derivative lacking the N-terminal lipid membrane anchor, determined by multidimensional solution nuclear magnetic resonance (NMR) spectroscopy. The structure reveals a central five-stranded β-sheet against which pack a long C-terminal and a short N-terminal α-helix, as found in homologues of LptE from other Gram-negative bacteria. One unique feature is an extended C-terminal helix in Pa LptE, which in a model of the Pa LptD/E complex appears to be long enough to contact the periplasmic domain of LptD. Chemical shift mapping experiments suggest only weak interactions occur between LptE and the oligosaccharide chains of LPS. The NMR structure of Pa LptE will be valuable for more detailed structural studies of the LptD/E complex from P. aeruginosa. PMID:27166502

  13. PREFACE: 3rd International Congress on Mechanical Metrology (CIMMEC2014)

    NASA Astrophysics Data System (ADS)

    2015-10-01

    From October 14th to 16th 2014, The Brazilian National Institute of Metrology, Quality, and Technology (Inmetro) and the Brazilian Society of Metrology (SBM) organized the 3rd International Congress on Mechanical Metrology (3rd CIMMEC). The 3rd CIMMEC was held in the city of Gramado, Rio Grande do Sul, Brazil. Anticipating the interest and enthusiasm of the technical-scientific community, the Organizing Institutions invite people and organizations to participate in this important congress, reiterating the commitment to organize an event according to highest international standards. This event has been conceived to integrate people and organizations from Brazil and abroad in the discussion of advanced themes in metrology. Manufacturers and dealers of measuring equipment and standards, as well as of auxiliary accessories and bibliographic material, had the chance to promote their products and services in stands at the Fair, which has taken place alongside the Congress. The 3rd CIMMEC consisted of five Keynote Speeches and 116 regular papers. Among the regular papers, the 25 most outstanding ones, comprising a high quality content on Mechanical Metrology, were selected to be published in this issue of Journal of Physics: Conference Series. It is our great pleasure to present this volume of Journal of Physics: Conference Series to the scientific community to promote further research in Mechanical Metrology and related areas. We believe that this volume will be both an excellent source of scientific material in the fast evolving fields that were covered by CIMMEC 2014.

  14. National--Alliance for Arts Education; JDR 3rd Fund

    ERIC Educational Resources Information Center

    Rogers, Forbes W.; Bloom, Kathryn

    1978-01-01

    The Alliance for Arts Education is an educational project embracing organizations and individuals at the national, state, and local levels with a mutual commitment to the arts as an integral part of the educational process. The JDR 3rd Fund provides consultant and technical services and, through coordination of the League of Cities for the Arts in…

  15. Structural and Functional Characterization of the LPS Transporter LptDE from Gram-Negative Pathogens.

    PubMed

    Botos, Istvan; Majdalani, Nadim; Mayclin, Stephen J; McCarthy, Jennifer Gehret; Lundquist, Karl; Wojtowicz, Damian; Barnard, Travis J; Gumbart, James C; Buchanan, Susan K

    2016-06-01

    Incorporation of lipopolysaccharide (LPS) into the outer membrane of Gram-negative bacteria is essential for viability, and is accomplished by a two-protein complex called LptDE. We solved crystal structures of the core LptDE complexes from Yersinia pestis, Klebsiella pneumoniae, Pseudomonas aeruginosa, and a full-length structure of the K. pneumoniae LptDE complex. Our structures adopt the same plug and 26-strand β-barrel architecture found recently for the Shigella flexneri and Salmonella typhimurium LptDE structures, illustrating a conserved fold across the family. A comparison of the only two full-length structures, SfLptDE and our KpLptDE, reveals a 21° rotation of the LptD N-terminal domain that may impart flexibility on the trans-envelope LptCAD scaffold. Utilizing mutagenesis coupled to an in vivo functional assay and molecular dynamics simulations, we demonstrate the critical role of Pro231 and Pro246 in the function of the LptD lateral gate that allows partitioning of LPS into the outer membrane. PMID:27161977

  16. 75 FR 55313 - Record of Decision (ROD) for Conversion of the 3rd Armored Cavalry Regiment (3rd ACR) to a...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-10

    ... Department of the Army Record of Decision (ROD) for Conversion of the 3rd Armored Cavalry Regiment (3rd ACR...: Notice of Availability (NOA). SUMMARY: The Department of the Army announces a ROD for conversion of the... conversion, the 3rd ACR will provide the Army with a force structure that has the flexibility to...

  17. Meeting report on the 3rd International Congress on Developmental Origins of Health and Disease (DOHaD)

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Developmental Origins of Health and Disease (DOHaD) focuses on the earliest stages of human development, and provides a novel paradigm to complement other strategies for lifelong prevention of common chronic health conditions. The 3rd International Congress on DOHaD, held in 2005, retained the most ...

  18. 3rd latin american and Caribbean congress on health economics.

    PubMed

    Pérez Izquierdo, Victoria; Alvarez Muñiz, Manuel

    2009-02-01

    The 3rd Latin American and Caribbean Congress on Health Economics took place at Havana Convention Center from 28th to 31st October 2008. The conference was an excellent opportunity for the exchange of personal encounters regarding health economics and its related disciplines from the perspectives of research, teaching and management. Specialists from mostly Latin American countries attended the event. High-ranking specialists from other countries highlighted the importance and popularity of the conference. A total of 313 delegates from 23 countries were present at the congress, 160 of whom were Cuban. PMID:19371176

  19. Precipitation Model Validation in 3rd Generation Aeroturbine Disc Alloys

    NASA Technical Reports Server (NTRS)

    Olson, G. B.; Jou, H.-J.; Jung, J.; Sebastian, J. T.; Misra, A.; Locci, I.; Hull, D.

    2008-01-01

    In support of application of the DARPA-AIM methodology to the accelerated hybrid thermal process optimization of 3rd generation aeroturbine disc alloys with quantified uncertainty, equilibrium and diffusion couple experiments have identified available fundamental thermodynamic and mobility databases of sufficient accuracy. Using coherent interfacial energies quantified by Single-Sensor DTA nucleation undercooling measurements, PrecipiCalc(TM) simulations of nonisothermal precipitation in both supersolvus and subsolvus treated samples show good agreement with measured gamma particle sizes and compositions. Observed longterm isothermal coarsening behavior defines requirements for further refinement of elastic misfit energy and treatment of the parallel evolution of incoherent precipitation at grain boundaries.

  20. Detection and clinical evolution of scrapie in sheep by 3rd eyelid biopsy.

    PubMed

    Vargas, Francisco; Luján, Lluís; Bolea, Rosa; Monleón, Eva; Martín-Burriel, Inmaculada; Fernández, Antonio; De Blas, Ignacio; Badiola, Juan José

    2006-01-01

    The goal of this article was to characterize the clinical evolution of scrapie in naturally affected sheep. Eighteen sheep with scrapie diagnosed by examination of 3rd eyelid biopsy and 12 control ewes were studied throughout the duration of their disease. Diagnosis was confirmed postmortem by histopathologic, immunohistochemical, and Western blot analysis of nervous tissue. Complete clinical examinations were performed every 2 weeks for each animal, of which 3 clinical examinations per animal are reported. Those clinical signs that showed a significant frequency within the corresponding clinical examination were considered representative of each stage of the disease (ie, early, middle, and late). The representative clinical signs for the early stage were hypoesthesia in the limbs, alteration of mental status, and a body condition score <3. Remarkably, hypoesthesia in the limbs was one of the 1st signs appearing during the early clinical stage in the affected animals, even before the appearance of other signs. For the middle stage, representative signs were the same as those for the early stage, together with hyporreflexia in the limbs, cardiac arrhythmia, pruritus/wool loss, and the appearance of the nibbling reflex. Representative clinical signs for the late stage were the same as those for the early and middle stage, together with head tremors, hyperexcitability to external stimuli, ataxia or gait abnormalities, and teeth grinding. On the basis of these results, we propose the calculation of an objective clinical index that allows the differentiation among clinical stages and that could be useful for further studies. The usefulness of 3rd eyelid lymphoid tissue biopsies for sequential clinical studies in naturally scrapie-affected sheep is demonstrated. PMID:16496940

  1. Designing a 3rd generation, authenticatable attribute measurement system

    SciTech Connect

    Thron, Jonathan; Karpius, Peter; Santi, Peter; Smith, Morag; Vo, Duc; Williams, Richard

    2009-01-01

    Attribute measurement systems (AMS) are designed to measure potentially sensitive items containing Special Nuclear Materials to determine if the items possess attributes which fall within an agreed-upon range. Such systems could be used in a treaty to inspect and verify the identity of items in storage without revealing any sensitive information associated with the item. An AMS needs to satisfy two constraints: the host party needs to be sure that none of their sensitive information is released, while the inspecting party wants to have confidence that the limited amount of information they see accurately reflects the properties of the item being measured. The former involves 'certifying' the system and the latter 'authenticating' it. Previous work into designing and building AMS systems have focused more on the questions of certifiability than on the questions of authentication - although a few approaches have been investigated. The next step is to build a 3rd generation AMS which (1) makes the appropriate measurements, (2) can be certified, and (3) can be authenticated (the three generations). This paper will discuss the ideas, options, and process of producing a design for a 3rd generation AMS.

  2. Microstructure Modeling of 3rd Generation Disk Alloys

    NASA Technical Reports Server (NTRS)

    Jou, Herng-Jeng

    2010-01-01

    The objective of this program is to model, validate, and predict the precipitation microstructure evolution, using PrecipiCalc (QuesTek Innovations LLC) software, for 3rd generation Ni-based gas turbine disc superalloys during processing and service, with a set of logical and consistent experiments and characterizations. Furthermore, within this program, the originally research-oriented microstructure simulation tool will be further improved and implemented to be a useful and user-friendly engineering tool. In this report, the key accomplishment achieved during the second year (2008) of the program is summarized. The activities of this year include final selection of multicomponent thermodynamics and mobility databases, precipitate surface energy determination from nucleation experiment, multiscale comparison of predicted versus measured intragrain precipitation microstructure in quench samples showing good agreement, isothermal coarsening experiment and interaction of grain boundary and intergrain precipitates, primary microstructure of subsolvus treatment, and finally the software implementation plan for the third year of the project. In the following year, the calibrated models and simulation tools will be validated against an independently developed experimental data set, with actual disc heat treatment process conditions. Furthermore, software integration and implementation will be developed to provide material engineers valuable information in order to optimize the processing of the 3rd generation gas turbine disc alloys.

  3. 3rd grade English language learners making sense of sound

    NASA Astrophysics Data System (ADS)

    Suarez, Enrique; Otero, Valerie

    2013-01-01

    Despite the extensive body of research that supports scientific inquiry and argumentation as cornerstones of physics learning, these strategies continue to be virtually absent in most classrooms, especially those that involve students who are learning English as a second language. This study presents results from an investigation of 3rd grade students' discourse about how length and tension affect the sound produced by a string. These students came from a variety of language backgrounds, and all were learning English as a second language. Our results demonstrate varying levels, and uses, of experiential, imaginative, and mechanistic reasoning strategies. Using specific examples from students' discourse, we will demonstrate some of the productive aspects of working within multiple language frameworks for making sense of physics. Conjectures will be made about how to utilize physics as a context for English Language Learners to further conceptual understanding, while developing their competence in the English language.

  4. Results from the UK 3rd generation programme: Albion

    NASA Astrophysics Data System (ADS)

    McEwen, R. K.; Axcell, C.; Knowles, P.; Hoade, K. P.; Wilson, M.; Dennis, P. N. J.; Backhouse, P.; Gordon, N. T.

    2008-10-01

    Following the development of 1st Generation systems in the 1970s, thermal imaging has been in service with the UK armed forces for over 25 years and has proven itself to be a battle winning technology. More recently the wider accessibility to similar technologies within opposing forces has reduced the military advantage provided by these 1st Generation systems and a clear requirement has been identified by the UK MOD for thermal imaging sensors providing increased detection, recognition and identification (DRI) ranges together with a simplified logistical deployment burden and reduced through-life costs. In late 2005, the UK MOD initiated a programme known as "Albion" to develop high performance 3rd Generation single waveband infrared detectors to meet this requirement. At the same time, under a separate programme supporting higher risk technology, a dual waveband infrared detector was also developed. The development phase of the Albion programme has now been completed and prototype detectors are now available and have been integrated into demonstration thermal imaging cameras. The Albion programme has now progressed into the second phase, incorporating both single and dual waveband devices, focussing on low rate initial production (LRIP) and qualification of the devices for military applications. All of the detectors have been fabricated using cadmium mercury telluride material (CMT), grown by metal organic vapour phase epitaxy (MOVPE) on low cost, gallium arsenide (GaAs) substrates and bump bonded to the silicon read out circuit (ROIC). This paper discusses the design features of the 3rd Generation detectors developed in the UK together with the results obtained from the prototype devices both in the laboratory and when integrated into field deployable thermal imaging cameras.

  5. LptA Assembles into Rod-Like Oligomers Involving Disorder-to-Order Transitions

    NASA Astrophysics Data System (ADS)

    Santambrogio, Carlo; Sperandeo, Paola; Villa, Riccardo; Sobott, Frank; Polissi, Alessandra; Grandori, Rita

    2013-10-01

    LptA is a periplasmic protein involved in the transport of lipopolysaccharide (LPS) from the inner membrane (IM) to the outer membrane (OM) of Gram-negative bacteria. Growing evidence supports a model in which LptA assembles into oligomers, forming a physical bridge connecting IM and OM. This work investigates assembly and architecture of LptA oligomers. Circular dichroism and "native" electrospray-ionization ion-mobility mass spectrometry (ESI-IM-MS) are employed to test concentration dependence of LptA structural features and to analyze the morphology of higher-order aggregates. The results show that LptA progressively assembles into rod-like oligomers without fixed stoichiometry, and grows by an n + 1 mechanism up to at least the pentamer. The oligomerization process induces disorder-to-order transitions in the polypeptide chain. Comparison with crystallographic and computational data suggests that these conformational changes likely involve short disordered regions at the N- and C-termini of monomeric LptA. The protein response to thermal denaturation displays strong concentration dependence, indicating that oligomerization increases protein stability. LptA conformational stability can also be enhanced by in vitro LPS binding. The genesis of these fibrillar structures could be relevant for the correct transport of LPS across the bacterial periplasm.

  6. LPT. Shield test facility (TAN645) interior. Mechanical equipment room with ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-645) interior. Mechanical equipment room with airwasher and refrigeration compressor. Photographer: Jack L. Anderson. Date: February 20, 1959. INEEL negative no. 59-855 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  7. LPT. Shield test facility (TAN645) interior. Mechanical equipment room with ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-645) interior. Mechanical equipment room with switchgear and control boards. Photographer: Jack L. Anderson. Date: February 20, 1959. INEEL negative no. 59-858 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  8. LPT. Shield test facility (TAN646) interior. Addition of third steam ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-646) interior. Addition of third steam generator. Burner end. Camera facing southwest. Photographer: Comiskey. Date: January 20, 1965. INEEL negative no. 65-242 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  9. LPT. EBOR (TAN646) reactor vault. Concrete blocks for reactor shielding ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. EBOR (TAN-646) reactor vault. Concrete blocks for reactor shielding going into shield test facility pool. Photographer: Comiskey. Date: February 19, 1965. INEEL negative no. 65-933 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  10. Differential contribution of specific working memory components to mathematics achievement in 2nd and 3rd graders.

    PubMed

    Meyer, M L; Salimpoor, V N; Wu, S S; Geary, D C; Menon, V

    2010-04-01

    The contribution of the three core components of working memory (WM) to the development of mathematical skills in young children is poorly understood. The relation between specific WM components and Numerical Operations, which emphasize computation and fact retrieval, and Mathematical Reasoning, which emphasizes verbal problem solving abilities in 48 2nd and 50 3rd graders was assessed using standardized WM and mathematical achievement measures. For 2nd graders, the central executive and phonological components predicted Mathematical Reasoning skills; whereas the visuo-spatial component predicted both Mathematical Reasoning and Numerical Operations skills in 3rd graders. This pattern suggests that the central executive and phonological loop facilitate performance during early stages of mathematical learning whereas visuo-spatial representations play an increasingly important role during later stages. We propose that these changes reflect a shift from prefrontal to parietal cortical functions during mathematical skill acquisition. Implications for learning and individual differences are discussed. PMID:21660238

  11. Structural and functional studies of conserved nucleotide-binding protein LptB in lipopolysaccharide transport

    SciTech Connect

    Wang, Zhongshan; Xiang, Quanju; Zhu, Xiaofeng; Dong, Haohao; He, Chuan; Wang, Haiyan; Zhang, Yizheng; Wang, Wenjian; Dong, Changjiang

    2014-09-26

    Highlights: • Determination of the structure of the wild-type LptB in complex with ATP and Mg{sup 2+}. • Demonstrated that ATP binding residues are essential for LptB’s ATPase activity and LPS transport. • Dimerization is required for the LptB’s function and LPS transport. • Revealed relationship between activity of the LptB and the vitality of E. coli cells. - Abstract: Lipopolysaccharide (LPS) is the main component of the outer membrane of Gram-negative bacteria, which plays an essential role in protecting the bacteria from harsh conditions and antibiotics. LPS molecules are transported from the inner membrane to the outer membrane by seven LPS transport proteins. LptB is vital in hydrolyzing ATP to provide energy for LPS transport, however this mechanism is not very clear. Here we report wild-type LptB crystal structure in complex with ATP and Mg{sup 2+}, which reveals that its structure is conserved with other nucleotide-binding proteins (NBD). Structural, functional and electron microscopic studies demonstrated that the ATP binding residues, including K42 and T43, are crucial for LptB’s ATPase activity, LPS transport and the vitality of Escherichia coli cells with the exceptions of H195A and Q85A; the H195A mutation does not lower its ATPase activity but impairs LPS transport, and Q85A does not alter ATPase activity but causes cell death. Our data also suggest that two protomers of LptB have to work together for ATP hydrolysis and LPS transport. These results have significant impacts in understanding the LPS transport mechanism and developing new antibiotics.

  12. PREFACE: 3rd International Conference on Hadron Physics (TROIA'11)

    NASA Astrophysics Data System (ADS)

    Erkol, Güray; Küçükarslan, Ayşe; Özpineci, Altuğ

    2012-03-01

    The 3rd International Conference on Hadron Physics, TROIA'11 was held at Canakkale, Turkey on 22-25 August 2011. Ozyegin University, Middle East Technical University, Canakkale Onsekiz Mart University and HadronPhysics2 Consortium sponsored the conference. Its aim was to bring together the experts and young scientists working on experimental and theoretical hadron physics. About 60 participants from 12 countries attended the conference. The topics covered included: Chiral Perturbation Theory QCD Sum Rules Effective Field Theory Exotic Hadrons Hadron Properties from Lattice QCD Experimental Results and Future Perspectives Hadronic Distribution Amplitudes The conference presentations were organized such that the morning sessions contained invited talks and the afternoon sessions were devoted to contributed talks and poster presentations. The speakers of the invited talks were: D Melikhov, M Nielsen, M Oka, E Oset, S Scherer, T T Takahashi and R Wanke. The conference venue was a resort hotel near Canakkale. As a social program, a guided full-day excursion to the excavation site of the ancient town of Troia and Assos was organized. We believe that this conference provided a medium for young scientists and experts in the field to effectively communicate and share ideas. We would like to express our sincere thanks to all participants for their contributions and stimulating discussions. We are also grateful to the Scientific Secretary, Kadir Utku Can, and all other members of the Organizing Committee for their patience and efforts. 13 February 2012 The Editors Güray Erkol Ayşe Küçükarslan Altuğ Özpineci Conference photograph

  13. PREFACE: 3rd International Meeting on Silicene (IMS-3)

    NASA Astrophysics Data System (ADS)

    Kara, Abdelkader; Enriquez, Hanna; Lemaire, Jean Louis; Oughaddou, Hamid

    2014-03-01

    . Historical summary Every two years, the STARM (science, technologie avanc\\'ee et recherche pour la Mediterran\\'ee, http://www.starm.emcmre.org/) society is organizing an international conference entitled Euro-Mediterranean Conference on Materials and Renewable Energies (EMCMRE, http://www.emcmre.org/) in countries across the Mediterranean Sea. It is in this framework that an international meeting dedicated to silicene is organized simultaneously since 2010: 1st International Meeting of Silicene (IMS-1), Safi, Morocco, 2010 2nd International Meeting of Silicene (IMS-2), Marrakech, Morocco, 2011 3rd International Meeting of Silicene (IMS-3), Istres-Marseille, France, 2013 Conference pictures are available in the PDF

  14. PREFACE: 3rd International Symposium ''Optics and its Applications''

    NASA Astrophysics Data System (ADS)

    Calvo, M. L.; Dolganova, I. N.; Gevorgyan, N.; Guzman, A.; Papoyan, A.; Sarkisyan, H.; Yurchenko, S.

    2016-01-01

    The SPIE.FOCUS Armenia: 3rd International Symposium ''Optics and its Applications'' (OPTICS-2015) http://rau.am/optics2015/ was held in Yerevan, Armenia, in the period October 1 - 5, 2015. The symposium was organized by the International Society for Optics and Photonics (SPIE), the Armenian SPIE student chapter with collaboration of the Armenian TC of ICO, the Russian-Armenian University (RAU), the Institute for Physical Research of National Academy of Sciences of Armenia (IPR of NAS), the Greek-Armenian industrial company LT-PYRKAL, and the Yerevan State University (YSU). The Symposium was co-organized by the SPIE & OSA student chapters of BMSTU, the Armenian OSA student chapter, and the SPIE student chapters of Lund University and Wroclaw University of Technology. The symposium OPTICS-2015 was dedicated to the International Year of Light and Light-Based Technologies. OPTICS-2015 was devoted to modern topics and optical technologies such as: optical properties of nanostructures, silicon photonics, quantum optics, singular optics & its applications, laser spectroscopy, strong field optics, biomedical optics, nonlinear & ultrafast optics, photonics & fiber optics, and mathematical methods in optics. OPTICS-2015 was attended by 100 scientists and students representing 17 countries: Armenia, China, Czech Republic, France, Georgia, Germany, India, Iran, Italy, Latvia, Mexico, Poland, Russia, Saudi Arabia, Sweden, Ukraine, and USA. Such a broad international community confirmed the important mission of science to be a uniting force between different countries, religions, and nations. We hope that OPTICS-2015 inspired and motivated students and young scientists to work in optics and in science in general. The present volume of Journal of Physics: Conference Series includes proceedings of the symposium covering various aspects of modern problems in optics. We are grateful to all people who were involved in the organization process. We gratefully acknowledge support from

  15. An Evidence-Based Approach to Estimating the National and State Costs of PreK-3rd. FCD Policy Brief Advancing PK-3rd. No.10

    ERIC Educational Resources Information Center

    Picus, Lawrence O.; Odden, Allan; Goetz, Michael

    2009-01-01

    This study estimates the costs of providing a high-quality PreK-3rd education approach in all 50 states plus the District of Columbia. Relying on an Evidence-Based approach to school finance adequacy, it identifies the staffing resources needed to offer high-quality integrated PreK-3rd programs and then estimates the costs of those resources. By…

  16. PREFACE: 3rd International Congress on Ceramics (ICC3)

    NASA Astrophysics Data System (ADS)

    Niihara, Koichi; Ohji, Tatsuki; Sakka, Yoshio

    2011-10-01

    Early in 2005, the American Ceramic Society, the European Ceramic Society and the Ceramic Society of Japan announced a collaborative effort to provide leadership for the global ceramics community that would facilitate the use of ceramic and glass materials. That effort resulted in an agreement to organize a new biennial series of the International Congress on Ceramics, convened by the International Ceramic Federation (ICF). In order to share ideas and visions of the future for ceramic and glass materials, the 1st International Congress on Ceramics (ICC1) was held in Canada, 2006, under the organization of the American Ceramic Society, and the 2nd Congress (ICC2) was held in Italy, 2008, hosted by the European Ceramic Society. Organized by the Ceramic Society of Japan, the 3rd Congress (ICC3) was held in Osaka, Japan, 14-18 November 2010. Incorporating the 23rd Fall Meeting of the Ceramic Society of Japan and the 20th Iketani Conference, ICC3 was also co-organized by the Iketani Science and Technology Foundation, and was endorsed and supported by ICF, Asia-Oceania Ceramic Federation (AOCF) as well as many other organizations. Following the style of the previous two successful Congresses, the program was designed to advance ceramic and glass technologies to the next generation through discussion of the most recent advances and future perspectives, and to engage the worldwide ceramics community in a collective effort to expand the use of these materials in both conventional as well as new and exciting applications. ICC3 consisted of 22 voluntarily organized symposia in the most topical and essential themes of ceramic and glass materials, including Characterization, design and processing technologies Electro, magnetic and optical ceramics and devices Energy and environment related ceramics and systems Bio-ceramics and bio-technologies Ceramics for advanced industry and safety society Innovation in traditional ceramics It also contained the Plenary Session and the

  17. 80. GENERAL VIEW TO NORTH ON 3RD AVENUE EL AT ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    80. GENERAL VIEW TO NORTH ON 3RD AVENUE EL AT GUN HILL STATION. 7TH AVENUE EL EXPRESS IS VISIBLE ABOVE THE 3RD AVENUE EL WHICH JOINED ONTO THE SAME STRUCTURE AT GUN HILL ROAD. NOTE: GUN HILL ROAD IS THE NORTH TERMINUS OF THE 3RD AVENUE ELEVATED. TRAINS DID NOT CARRY PASSENGERS BEYOND THIS POINT, ALTHOUGH THE 3RD AVENUE TRACK DID EXTEND FURTHER NORTH FOR SWITCHING PURPOSES AND INTO THE YARDS. - Interborough Rapid Transit Company, Third Avenue Elevated Line, Borough of the Bronx, New York County, NY

  18. [3rd Hungarian Breast Cancer Consensus Conference - Radiotherapy Guidelines].

    PubMed

    Polgár, Csaba; Kahán, Zsuzsanna; Csejtei, András; Gábor, Gabriella; Landherr, László; Mangel, László; Mayer, Árpád; Fodor, János

    2016-09-01

    The radiotherapy expert panel revised and updated the radiotherapy (RT) guidelines accepted in 2009 at the 2nd Hungarian Breast Cancer Consensus Conference based on new scientific evidence. Radiotherapy of the conserved breast is indicated in ductal carcinoma in situ (St. 0), as RT decreases the risk of local recurrence by 60%. In early stage (St. I-II) invasive breast cancer RT remains a standard treatment following breast conserving surgery. However, in elderly (≥70 years) patients with stage I, hormone receptor positive tumour hormonal therapy without RT can be considered. Hypofractionated (15×2.67 Gy) whole breast irradiation and for selected cases accelerated partial breast irradiation are validated treatment alternatives of conventional (25×2 Gy) whole breast irradiation. Following mastectomy RT significantly decreases the risk of locoregional recurrence and improves overall survival of patients having 1 to 3 (pN1a) or ≥4 (pN2a, pN3a) positive axillary lymph nodes. In selected cases of patients with 1 to 2 positive sentinel lymph nodes axillary dissection can be omitted and substituted with axillary RT. After neoadjuvant chemotherapy (NAC) followed by breast conserving surgery whole breast irradiation is mandatory, while after NAC followed by mastectomy locoregional RT should be given in cases of initial stage III-IV and ypN1 axillary status. PMID:27579722

  19. LPT. Shield test facility (TAN646) interior. Pool room nearly complete. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-646) interior. Pool room nearly complete. Fifty-ton bridge crane is ready for operation. Water fills foreground pool. Photographer: M. Holmes. Date: June 23, 1959. INEEL negative no. 59-3263 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  20. LPT. Low power test (TAN641) interior. Heating and ventilating pneumatic ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Low power test (TAN-641) interior. Heating and ventilating pneumatic and electrical control panel. Contract nearly complete. Photographer: Jack L. Anderson. Date: December 19, 1957. INEEL negative no. 57-6198 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  1. LPT. Low power test control building (TAN641) interior. Camera facing ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Low power test control building (TAN-641) interior. Camera facing west. Office area. (Open) door to special source vault at center of view. INEEL negative no. HD-40-4-1 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  2. LPT. Low power test (TAN641) interior. Camera is inside special ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Low power test (TAN-641) interior. Camera is inside special source vault and facing southeast. Interior grill door is closed; outer steel door is open. Photographer: Jack L. Anderson. Date: December 19, 1957. INEEL negative no. 57-6197 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  3. LPT. EBOR (TAN646) interior. Camera is facing north and down ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. EBOR (TAN-646) interior. Camera is facing north and down into reactor vault. View shows portion of the lead shutdown shield, pressure vessel thimbles, and refueling ports mounted on pressure vessel head. Concrete shielding below. Photographer: Farmer. Date: May 24, 1965. INEEL negative no. 65-2739 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  4. LPT. Low power test (TAN641) interior of mechanical equipment room. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Low power test (TAN-641) interior of mechanical equipment room. Air compressors in left foreground. Evaporate condenser in right background. Construction 93% complete. Photographer: Jack L. Anderson. Date: October 23, 1957. INEEL negative no. 57-5340 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  5. LPT. Low power test cell in TAN640. Interior of north ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Low power test cell in TAN-640. Interior of north cell. Camera faces southwest. Corner shows south and west walls. Mezzanine provided access to experiments. INEEL negative no. HD-40-2-1 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  6. LPT. Shield test facility test building interior (TAN646). Camera points ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility test building interior (TAN-646). Camera points down into interior of north pool. Equipment on wall is electronical bus used for post-1970 experiment. Personnel ladder at right. INEEL negative no. HD-40-9-1 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  7. LPT. Low power test (TAN640) interior. Basement level. Camera facing ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Low power test (TAN-640) interior. Basement level. Camera facing north. Cable trays and conduit cross tunnel between critical experiment cell and critical experiment control room. Construction 93% complete. Photographer: Jack L. Anderson. Date: October 23, 1957. INEEL negative no. 57-5339 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  8. LPT. EBOR interior. Inside room B105. Camera facing northwest from ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. EBOR interior. Inside room B105. Camera facing northwest from southeast corner of room. Typical view of sample tube panels. Photographer: Comiskey. Date: Fabruary 19, 1965. INEEL negative no. 65-934 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  9. LPT. Shield test facility (TAN646). Sections and details of water ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-646). Sections and details of water management areas. Ralph M. Parsons 1229-17 ANP/GE-6-646-P-3. April 1957. Approved by INEEL Classification Office for public release. INEEL index code no. 037-0646-51-693-107388 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  10. LPT. EBOR (TAN646). Floor plan for new helium management wing. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. EBOR (TAN-646). Floor plan for new helium management wing. Detail of sample vault and basement switch room. Kaiser engineers EBOR/GA-646-A-101. Date: May 1963. INEEL index code no. 037-0646-00-486-119115 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  11. LPT. Shield test facility (TAN646) interior. Construction worker applies caulking ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-646) interior. Construction worker applies caulking compound to joint between stainless steel weir and concrete. Photographer: Jack L. Anderson. Date: March 6, 1959. INEEL negative no. 59-1099 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  12. LPT. Shield test facility (TAN645) interior remodel for EBOR. Room ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-645) interior remodel for EBOR. Room 122 complete. Camera facing west. Photographer: Page Comiskey. Date: ca. August 20, 1965. INEEL negative no. 65-4330 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  13. LPT. Shield test facility (TAN645) interior remodel for EBOR. Room ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-645) interior remodel for EBOR. Room 124 complete, camera facing north. Photographer: Page Comiskey. Date: ca. August 20, 1965. INEEL negative no. 65-4331 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  14. LPT. Low power assembly and test building (TAN640) south facade. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Low power assembly and test building (TAN-640) south facade. Camera facing north. Note one-story pumice block corridor, which provided inside access between control building (at left edge of view) and test cell. INEEL negative no. HD-40-1-2 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  15. LPT. Shield test facility (TAN645) interior. Boiler room shows one ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-645) interior. Boiler room shows one boiler, diesel electric stand unit, and related equipment. Pumice block walls. Photographer: Jack L. Anderson. Date: January 19, 1959. INEEL negative no. 59-286 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  16. LPT. Shield test facility (TAN646) exterior, as modified for EBOR. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-646) exterior, as modified for EBOR. Camera facing northeast. Heat exchange fans, helium storage tanks, and completed EBOR perimeter road. Photographer: Page Comisky. Date: ca. August 20, 1965. INEEL negative no. 65-4328 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  17. LPT. Low power test control building (TAN641) east facade. Sign ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Low power test control building (TAN-641) east facade. Sign says "Energy and Systems Technology Laboratory, INEL" (Post-ANP-use). Camera facing west. INEEL negative no. HD-40-3-2 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  18. LPT. Shield test control building (TAN645), north facade. Camera facing ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test control building (TAN-645), north facade. Camera facing south. Obsolete sign dating from post-1970 program says "Energy and Systems Technology Experimental Facility, INEL." INEEL negative no. HD-40-5-4 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  19. LPT. Shield test facility (TAN646) interior. Water treatment room contains ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-646) interior. Water treatment room contains water softeners, deionizers, and display panel. Note metal ceiling and walls. Photographer: Jack L. Anderson. Date: February 20, 1959. INEEL negative no. 59-856 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  20. LPT. EBOR (TAN646) interior, installing reactor in STF pool ("vault"). ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. EBOR (TAN-646) interior, installing reactor in STF pool ("vault"). Pressure vessel shows core barrel and outlet nozzle (next to man below) to inner duct weld, which is prepared and in position for stress relieving. Camera facing southeast. Photographer: Comiskey. Date: January 20, 1965. INEEL negative no. 65-239 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  1. LPT. Low power assembly and test building (TAN640). Camera facing ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Low power assembly and test building (TAN-640). Camera facing west. Rollup doors to each test cell face east. Concrete walls poured in place. Apparatus at right of view was part of a post-ANP program. INEEL negative no. HD-40-1-1 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  2. LPT. EBOR (TAN646) reactor vessel, flow distribution tank. Outlet nozzle ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. EBOR (TAN-646) reactor vessel, flow distribution tank. Outlet nozzle on side of vessel will be connected to coolant duct. Photographer: Lowin. Date: January 20, 1965. INEEL negative no. 65-237 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  3. LPT. Shield test facility (TAN645 and 646). Calibration lab shield ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-645 and -646). Calibration lab shield door. Ralph M. Parsons 1229-17 ANP/GE-6-645-MS-1. April 1957. Approved by INEEL Classification Office for public release. INEEL index code no. 037-0645-40-693-107369 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  4. LPT. Low power test (TAN640) interior of cell 102. Camera ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Low power test (TAN-640) interior of cell 102. Camera looking west toward rear of cell. Five-ton bridge crane (Moffett, 10,000 lb.) and banks of lights at top of cell. Photographer: Jack L. Anderson. Date: December 19, 1957. INEEL negative no. 57-6200 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  5. LPT. Shield test facility assembly and test building (TAN646), south ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility assembly and test building (TAN-646), south end of EBOR helium wing. Camera facing north. Monorail protrudes from upper-level door. Rust marks on concrete wall are from stack. Metal shed is post-1970 addition. INEEL negative no. HD-40-8-1 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  6. 19. MILL NO. 1, 3rd FLOOR, CEILING TRACKING WITH AIR ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    19. MILL NO. 1, 3rd FLOOR, CEILING TRACKING WITH AIR CLEANER (BLEW DUST/LINT DOWNWARD WHILE TRAVELING ON TRACK OVER MILL MACHINERY). - Prattville Manufacturing Company, Number One, 242 South Court Street, Prattville, Autauga County, AL

  7. 1. WEST SIDE AND ENTRY, FROM ACROSS 3RD STREET, LOOKING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. WEST SIDE AND ENTRY, FROM ACROSS 3RD STREET, LOOKING EAST. - Oakland Naval Supply Center, Administration Building-Dental Annex-Dispensary, Between E & F Streets, East of Third Street, Oakland, Alameda County, CA

  8. 19. OFFSHORE VIEW OF 3RD TEE, LOOKING NORTHWEST, SHOWING SOUTHEAST ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    19. OFFSHORE VIEW OF 3RD TEE, LOOKING NORTHWEST, SHOWING SOUTHEAST SIDE OF TACKLE BOX IN FOREGROUND - Huntington Beach Municipal Pier, Pacific Coast Highway at Main Street, Huntington Beach, Orange County, CA

  9. 15. OFFSHORE VIEW OF PIER, LOOKING EASTNORTHEAST, 3RD TEE, SHOWING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    15. OFFSHORE VIEW OF PIER, LOOKING EAST-NORTHEAST, 3RD TEE, SHOWING RESTROOMS IN FOREGROUND WITH PUMPHOUSE AND TACKLE BOX BEHIND - Huntington Beach Municipal Pier, Pacific Coast Highway at Main Street, Huntington Beach, Orange County, CA

  10. 3rd International Conference on Turbulent Mixing and Beyond

    NASA Astrophysics Data System (ADS)

    Abarzhi, Snezhana I.; Gauthier, Serge; Keane, Christopher J.; Niemela, Joseph J.

    2013-07-01

    National Academies of Sciences and Engineering, and including researchers at experienced and early stages of their careers from leading scientific institutions in academia, national laboratories, corporations and industry, from developed and developing countries across five continents. The success of TMB-2011 consisted from the successful work of the conference participants, who were responsible professionals caring for the quality of their research and sharing their scientific vision. The level of presentations was high, and 205 presentations included about 50 invited lectures, nearly 70 oral talks (3500 min of talks in total), some 90 posters and one round table. The special course on 'Turbulence and Waves' was organized at TMB-2011 with the support of the US Office of Naval Research Global, and included nearly 40 lectures and talks (960 minutes of talks in total). TMB-2011 covered 16 different topics, maintaining the scope and the interdisciplinary character of the meeting and at the same time keeping the focus on a fundamental scientific problem of non-equilibrium processes and on the conference objectives. The topics included: • Canonical turbulent and turbulent mixing: invariant, scaling, spectral properties, scalar transports, convection. • Wall-bounded flows: structure and fundamentals, non-canonical turbulent boundary layers, including unsteady and transitional flows, supersonic and hypersonic flows, shock-boundary layer interactions. • Non-equilibrium processes: unsteady, multiphase and shock-driven turbulent flows, anisotropic non-local dynamics, connection of continuous description at macro-scales to kinetic processes at atomistic scales. • Interfacial dynamics: the instabilities of Rayleigh-Taylor, Kelvin-Helmholtz, Richtmyer-Meshkov, Landau-Darrieus, Saffmann-Taylor. • High energy density physics: inertial confinement and heavy-ion fusion, Z-pinches, light-material and laser-plasma interaction, non-equilibrium heat transfer. • Material science

  11. Survey of K-3rd-Grade Teachers' Knowledge of Ear Infections and Willingness to Participate in Prevention Programs

    ERIC Educational Resources Information Center

    Danhauer, Jeffrey L.; Johnson, Carole E.; Caudle, Abby T.

    2011-01-01

    Purpose: Ear infections are prevalent in kindergarten through 3rd-grade (K-3rd) children and can affect their performance at school. Chewing gum, when administered by parents and teachers, can help prevent ear infections in children. This pilot study surveyed K-3rd-grade teachers in the Santa Barbara School Districts to assess their knowledge…

  12. Enhanced Design of Turbo-jet LPT by Separation Control Using Phased Plasma Actuators

    NASA Technical Reports Server (NTRS)

    Ashpis, David (Technical Monitor); Corke, Thomas C.; Thomas, Flint O.

    2003-01-01

    This work deals with the documentation and control of flow separation that occurs over turbine blades in the low-pressure turbine stage at low Reynolds numbers that exist at high altitude cruise. We utilize a specially constructed linear cascade that is designed to study the flow field over a generic LPT cascade consisting of Pratt & Whitney 'Pak B' shaped blades. This facility was constructed under a previous one-year NASA Glenn RC initiative. The center blade in the cascade is instrumented to measure the surface pressure coefficient distribution. Optical access allows two-component LDV measurement for boundary layer profiles. Experimental conditions have been chosen to give a range of chord Reynolds numbers from 10 to 100K, and a range of free-stream turbulence levels from u'/U(sub infinity)= 0.08 to 3 percent. The surface pressure measurements were used to define a region of separation and reattachment that depend on the free-stream conditions. The location of separation was found to be relatively insensitive to the experimental conditions. However, reattachment location was very sensitive to the turbulence level and Reynolds number. Excellent agreement was found between the measured pressure distributions and predictions from Euler and RANS simulations. Two-component LDV measurements are presently underway to document the mean and fluctuating velocity components in the boundary layer over the center blade for the range of experimental conditions. The fabrication of the plasma actuator is underway. These are designed to produce either streamwise vortices, or a downstream-directed wall jet. A precursor experiment for the former approach was performed with an array of vortex generators placed just upstream of the separation line. These led to reattachment except for the lowest Reynolds number. Progress has also been made on the proposed concept for a laterally moving wake. This involved constructing a smaller wind tunnel and molding an array of symmetric airfoils

  13. Radiographic findings on 3rd molars removed in 20-year-old men.

    PubMed

    Rajasuo, Ari; Peltola, Jaakko; Ventä, Irja; Murtomaa, Heikki

    2003-10-01

    In this study we assess radiographic findings characteristic of mandibular 3rd molars that had required either routine or surgical extraction. X-ray findings relating to acute pericoronitis were also examined. The material was collected by investigating patient records and rotational panoramic radiographs of 20-year-old Finnish male conscripts (n = 738) treated during military service because of 3rd-molar-related problems. The follicle around the crown of mandibular 3rd molars with acute pericoronitis was enlarged in 19% of cases and in 13% of chronic symptom-free pericoronitis cases (not statistically significant difference). Mandibular 3rd molars extracted surgically were more often mesially inclined than those extracted routinely (61% vs. 23%; P < 0.001), partially or totally intrabony impacted (92% vs. 66%; P < 0.001) and deep situated (on average 4.2 mm vs. 2.5 mm under the occlusal plane). Surgical extraction was also associated with the roots completely developed [92% vs. 84% of the teeth routinely extracted, odds ratio (OR) 2.6, 95% confidence interval (CI) 1.2-5.5] and with the absence of radiographic pericoronitis [around 27% vs. 39% of the teeth routinely extracted (OR 0.5, 95% CI 0.3-0.8)]. In 86% of cases the space between 2nd molar and ramus of the mandible was narrower than the 3rd molar extracted surgically, whereas this was 62% in routine extraction cases (P < 0.001). We conclude that there are some typical 3rd-molar findings in rotational panoramic radiographs that show a need for surgical extraction. PMID:14763776

  14. LPT. Chlorination building (TAN643) and water well pumphouse (TAN644). Plans, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Chlorination building (TAN-643) and water well pumphouse (TAN-644). Plans, elevations, sections, and details. Ralph M. Parsons 1229-12 ANP/GE-7-643-A-S-H&V-1. November 1956. Approved by INEEL Classification Office for public release. INEEL index code no. 038-0643/0644-00-693-107307 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  15. Integrated testing of the Thales LPT9510 pulse tube cooler and the iris LCCE electronics

    NASA Astrophysics Data System (ADS)

    Johnson, Dean L.; Rodriguez, Jose I.; Carroll, Brian A.; Bustamante, John G.; Kirkconnell, Carl S.; Luong, Thomas T.; Murphy, J. B.; Haley, Michael F.

    2014-01-01

    The Jet Propulsion Laboratory (JPL) has identified the Thales LPT9510 pulse tube cryocooler as a candidate low cost cryocooler to provide active cooling on future cost-capped scientific missions. The commercially available cooler can provide refrigeration in excess of 2 W at 100K for 60W of power. JPL purchased the LPT9510 cooler for thermal and dynamic performance characterization, and has initiated the flight qualification of the existing cooler design to satisfy near-term JPL needs for this cooler. The LPT9510 has been thermally tested over the heat reject temperature range of 0C to +40C during characterization testing. The cooler was placed on a force dynamometer to measure the selfgenerated vibration of the cooler. Iris Technology has provided JPL with a brass board version of the Low Cost Cryocooler Electronics (LCCE) to drive the Thales cooler during characterization testing. The LCCE provides precision closed-loop temperature control and embodies extensive protection circuitry for handling and operational robustness; other features such as exported vibration mitigation and low frequency input current filtering are envisioned as options that future flight versions may or may not include based upon the mission requirements. JPL has also chosen to partner with Iris Technology for the development of electronics suitable for future flight applications. Iris Technology is building a set of radiation-hard, flight-design electronics to deliver to the Air Force Research Laboratory (AFRL). Test results of the thermal, dynamic and EMC testing of the integrated Thales LPT9510 cooler and Iris LCCE electronics is presented here.

  16. LPT. Low power test (TAN640 and 641) floor plan. Cells ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Low power test (TAN-640 and -641) floor plan. Cells 101 and 102, control rooms, shielded counting room, generator room, list of room numbers and names. Door details. Ralph M. Parsons 1229-12 ANP/GE-7-640-A-1. November 1956. Approved by INEEL Classification Office for public release. INEEL index code no. 038-0640-00-693-107274 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  17. Integrated testing of the Thales LPT9510 pulse tube cooler and the iris LCCE electronics

    SciTech Connect

    Johnson, Dean L.; Rodriguez, Jose I.; Carroll, Brian A.; Bustamante, John G.; Kirkconnell, Carl S.; Luong, Thomas T.; Murphy, J. B.; Haley, Michael F.

    2014-01-29

    The Jet Propulsion Laboratory (JPL) has identified the Thales LPT9510 pulse tube cryocooler as a candidate low cost cryocooler to provide active cooling on future cost-capped scientific missions. The commercially available cooler can provide refrigeration in excess of 2 W at 100K for 60W of power. JPL purchased the LPT9510 cooler for thermal and dynamic performance characterization, and has initiated the flight qualification of the existing cooler design to satisfy near-term JPL needs for this cooler. The LPT9510 has been thermally tested over the heat reject temperature range of 0C to +40C during characterization testing. The cooler was placed on a force dynamometer to measure the selfgenerated vibration of the cooler. Iris Technology has provided JPL with a brass board version of the Low Cost Cryocooler Electronics (LCCE) to drive the Thales cooler during characterization testing. The LCCE provides precision closed-loop temperature control and embodies extensive protection circuitry for handling and operational robustness; other features such as exported vibration mitigation and low frequency input current filtering are envisioned as options that future flight versions may or may not include based upon the mission requirements. JPL has also chosen to partner with Iris Technology for the development of electronics suitable for future flight applications. Iris Technology is building a set of radiation-hard, flight-design electronics to deliver to the Air Force Research Laboratory (AFRL). Test results of the thermal, dynamic and EMC testing of the integrated Thales LPT9510 cooler and Iris LCCE electronics is presented here.

  18. LPT. Shield test facility (TAN645 and 646). Sections show relationships ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-645 and -646). Sections show relationships among control rooms, coupling station, counting rooms, pools, equipment rooms, data room and other areas. Ralph M. Parsons 1229-17 ANP/GE-6-645-A-4. April 1957. Approved by INEEL Classification Office for public release. INEEL index code no. 037-0645/0646-00-693-107350 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  19. LPT. Shield test facility (TAN645 and 646). Elevations show three ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-645 and -646). Elevations show three types of siding: Asbestos cement, pumice block, concrete. Ralph M. Parsons 1229-17 ANP/GE-6-6445-A-3. April 1957. Approved by INEEL Classification Office for public release. INEEL index code no. 037-06445/0646-00-693-107349 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  20. LPT. Shield test facility (TAN646). Floor plan for water treatment ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility (TAN-646). Floor plan for water treatment room on west facade, tank and filter locations in basement along service tunnel and in coupling station. Ralph M. Parsons 1229-17 ANP/GE-6-646-P-2. April 1957. INEEL Index code no. 037-0645/0646-51-693-107387 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  1. LPT. Aerial of low power test (TAN640 and 641) and ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Aerial of low power test (TAN-640 and -641) and shield test (TAN-645 and -646) facilities. Camera facing north west. Low power test facility at right. Shield test facility at left. Flight engine test area in background at center left of view. Administrative and A&M areas at right. Photographer: Lowin. Date: February 24, 1965. INEEL negative no. 65-991 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  2. LPT. Aerial of low power test facility (TAN640 and 641) ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Aerial of low power test facility (TAN-640 and -641) and shield test facility (TAN-645 and -646). Camera facing south. Low power reactor cells at left, then one-story control building; diagonal fence; shield test control building, then (high-bay) pool room. In foreground are electrical pad, water tanks and guard house. Photographer: Lowin. Date: February 24, 1965. INEEL negative no. 65-987 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  3. LPT. Shield test facility assembly and test building (TAN646). East ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Shield test facility assembly and test building (TAN-646). East facade of ebor helium wing addition. Camera facing west. Note asbestos-cement siding on stair enclosure and upper-level. Concrete siding at lower level. Metal stack. Monorail protrudes from upper level of south wall at left of view. INEEL negative no. HD-40-7-4 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  4. Using Food as a Tool to Teach Science to 3rd Grade Students in Appalachian Ohio

    ERIC Educational Resources Information Center

    Duffrin, Melani W.; Hovland, Jana; Carraway-Stage, Virginia; McLeod, Sara; Duffrin, Christopher; Phillips, Sharon; Rivera, David; Saum, Diana; Johanson, George; Graham, Annette; Lee, Tammy; Bosse, Michael; Berryman, Darlene

    2010-01-01

    The Food, Math, and Science Teaching Enhancement Resource (FoodMASTER) Initiative is a compilation of programs aimed at using food as a tool to teach mathematics and science. In 2007 to 2008, a foods curriculum developed by professionals in nutrition and education was implemented in 10 3rd-grade classrooms in Appalachian Ohio; teachers in these…

  5. PreK-3rd: What Is the Price Tag? Policy to Action Brief. No. 2

    ERIC Educational Resources Information Center

    Shore, Rima

    2009-01-01

    In an era of intense fiscal pressures, educators are focusing on those investments most likely to lift student achievement. They are also trying to make more strategic use of existing resources. To achieve these goals, a growing number of policymakers are considering integrated PreK-3rd approaches. Increasingly, they are recognizing that the first…

  6. Patient protection at risk in IEC 60601-1 3rd edition.

    PubMed

    Dybdahl, K

    2009-09-01

    Engineers developing medical electrical equipment in accordance with IEC 60601-1 3rd edition are in immediate need of short- and long-term solutions to avoid potentially hazardous designs as a result of misinterpretation of the requirements. Several options are described to ensure consistency and safety of devices. PMID:19852179

  7. Evaluation of the "Respect Not Risk" Firearm Safety Lesson for 3rd-Graders

    ERIC Educational Resources Information Center

    Liller, Karen D.; Perrin, Karen; Nearns, Jodi; Pesce, Karen; Crane, Nancy B.; Gonzalez, Robin R.

    2003-01-01

    The purpose of this study was to evaluate the MORE HEALTH "Respect Not Risk" Firearm Safety Lesson for 3rd-graders in Pinellas County, Florida. Six schools representative of various socioeconomic levels were selected as the test sites. Qualitative and quantitative data were collected. A total of 433 matched pretests/posttests were used to…

  8. 75 FR 34450 - Filing Dates for the Indiana Special Election in the 3rd Congressional District

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-17

    ... From the Federal Register Online via the Government Publishing Office FEDERAL ELECTION COMMISSION Filing Dates for the Indiana Special Election in the 3rd Congressional District AGENCY: Federal Election Commission. ACTION: Notice of filing dates for special election. SUMMARY: Indiana has scheduled a...

  9. Prediction of High School Dropout or Graduation from 3rd Grade Data.

    ERIC Educational Resources Information Center

    Lloyd, Dee Norman; Bleach, Gail

    Measures of background characteristics, school performance, and tested achievement were analyzed for four race-by-sex samples of 3rd graders who were known to have later become high school dropouts or graduates. Results showed that as early as five to eight years before leaving school, dropouts differed significantly from graduates in age, tested…

  10. AL State Profile. Alabama: Alabama High School Graduation Exam (AHSGE), 3rd Edition

    ERIC Educational Resources Information Center

    Center on Education Policy, 2010

    2010-01-01

    This paper provides information about Alabama High School Graduation Exam, 3rd Edition, a comprehensive standards-based exam. The purpose of the exam is to: (1) Provide schools with student academic diagnostic information; (2) Determine prospective high school graduates' mastery of the state curriculum; (3) Increase alignment of local curriculum…

  11. 16. 3RD FLOOR, J.M. LEHMANN CO. FIVEROLL TOILET SOAP MILL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    16. 3RD FLOOR, J.M. LEHMANN CO. FIVE-ROLL TOILET SOAP MILL INSTALLED 1950, TO WEST; BUCKET CONVEYOR AT RIGHT MOVED WASTE FROM 2ND FLOOR SOAP PRESSES TO 5TH FLOOR RE-MANUFACTURE - Colgate & Company Jersey City Plant, Building No. B-14, 54-58 Grand Street, Jersey City, Hudson County, NJ

  12. Linking Learning: The PreK-3rd Path to School Success

    ERIC Educational Resources Information Center

    Advocates for Children of New Jersey, 2010

    2010-01-01

    Giving children high-quality preschool is the first step in the journey to school success. The next steps--kindergarten through 3rd grade--are equally important. Advocates for Children of New Jersey (ACNJ) is working on several fronts to help school districts across the state build strong early learning programs, which can significantly improve…

  13. 78. VIEW OF 3RD TEE, TAKEN FROM SOUTHEAST SIDE OF ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    78. VIEW OF 3RD TEE, TAKEN FROM SOUTHEAST SIDE OF PIER, FACING SOUTHWEST, SHOWING NORTHEAST SIDE OF THE TACKLE BOX (LEFT), SOUTHEAST SIDE AND NORTHEAST FRONT OF PUMPHOUSE (RIGHT), AND RESTROOMS IN BACKGROUND - Huntington Beach Municipal Pier, Pacific Coast Highway at Main Street, Huntington Beach, Orange County, CA

  14. Correlates and Phenomenology of 1st and 3rd Person Memories

    PubMed Central

    Sutin, Angelina R.; Robins, Richard W.

    2010-01-01

    The present research addressed fundamental questions about the visual perspective of autobiographical memories: Are stable personality characteristics associated with visual perspective? Does visual perspective influence the memory's phenomenological qualities? Participants in Study 1 (N = 1,684) completed individual-difference measures and indicated the perspective from which they generally retrieve memories. Participants in Study 2 (N = 706) retrieved a memory from their natural or manipulated perspective, rated its phenomenology, and completed the same individual-difference measures. Dissociation and anxiety were associated with 3rd person retrieval style; the Big Five personality traits were primarily unrelated to perspective. Compared to 3rd person memories, naturally-occurring 1st person memories were higher on Vividness, Coherence, Accessibility, Sensory Detail, Emotional Intensity, and Time Perspective and lower on Distancing; manipulating perspective eliminated these differences. Visual perspective is associated with clinically-relevant constructs and, although associated with the memory's phenomenology, perspective does not shape it. PMID:20665336

  15. Conference report: the 3rd Global CRO Council for Bioanalysis at the International Reid Bioanalytical Forum.

    PubMed

    Breda, Massimo; Garofolo, Fabio; Caturla, Maria Cruz; Couerbe, Philippe; Maltas, John; White, Peter; Struwe, Petra; Sangster, Timothy; Riches, Suzanne; Hillier, Jim; Garofolo, Wei; Zimmerman, Thomas; Pawula, Maria; Collins, Eileen; Schoutsen, Dick; Wieling, Jaap; Green, Rachel; Houghton, Richard; Jeanbaptiste, Bernard; Claassen, Quinton; Harter, Tammy; Seymour, Mark

    2011-12-01

    The 3rd Global CRO Council Closed Forum was held on the 3rd and 4th July 2011 in Guildford, United Kingdom, in conjunction with the 19th International Reid Bioanalytical Forum. In attendance were 21 senior-level representatives from 19 CROs on behalf of nine European countries and, for many of the attendees, this occasion was the first time that they had participated in a GCC meeting. Therefore, this closed forum was an opportunity to increase awareness of the aim of the GCC and how it works, share information about bioanalytical regulations and audit findings from different agencies, their policies and procedures and also to discuss some topics of interest and aim to develop ideas and provide recommendations for bioanalytical practices at future GCC meetings in Europe. PMID:22185271

  16. 1st Central and Eastern European Proteomic Conference and 3rd Czech Proteomic Conference.

    PubMed

    Kovarova, Hana; Gadher, Suresh Jivan; Archakov, Alexander

    2008-02-01

    The 1st Central and Eastern European Proteomic Conference was organized together with the 3rd Czech Proteomic Conference in the TOP Hotel, Prague in the Czech Republic from the 29th to the 31st October, 2007. The aim was to strengthen links with scientists from Central and Eastern Europe including Russia, which until now have been weak or nonexistent, and to highlight the emergence of excellent proteomic studies from various countries, which until now were not visible. PMID:18282121

  17. Higher order modes of a 3rd harmonic cavity with an increased end-cup iris

    SciTech Connect

    T. Khabibouline; N. Solyak; R. Wanzenberg

    2003-05-19

    The cavity design for a 3rd harmonic cavity for the TTF 2 photoinjector has been revised to increase the coupling between the main coupler and the cavity cells. The iris radius of the end cup of the cavity has been increased to accomplish a better coupling. The basic rf-parameters and the higher order modes of the modified design are summarized in this report.

  18. What is FirstSchool? Issues in PreK-3rd Education. Number One

    ERIC Educational Resources Information Center

    Ritchie, Sharon; Maxwell, Kelly; Clifford, Richard

    2009-01-01

    FirstSchool is part of a national PreK-3rd movement of schools, districts, educators and universities seeking to improve how children from ages 3 to 8 learn and develop in schools. While these different projects use a variety of names, all are working to connect high-quality PreK programs with high-quality elementary schools. FirstSchool is…

  19. 13. Photocopy of 1920 drawing titled: BUILDING 78, 3RD FLOOR ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    13. Photocopy of 1920 drawing titled: BUILDING 78, 3RD FLOOR BALCONY AND FIRE ESCAPES, including plans for skylight and North Elevation. HABS photograph is an 8x10' contact print made from a high contrast negative of an enlargement made from microfiche. Original is in the collection of Department of Public Works, Puget Sound Naval Shipyard, Bremerton, WA. - Puget Sound Naval Shipyard, Administration Building, Farragut Avenue, Bremerton, Kitsap County, WA

  20. Insights from the 3rd World Congress on Integrated Computational Materials Engineering

    NASA Astrophysics Data System (ADS)

    Howe, D.; Goodlet, B.; Weaver, J.; Spanos, G.

    2016-05-01

    The 3rd World Congress on Integrated Computational Materials Engineering (ICME) was a forum for presenting the "state-of-the-art" in the ICME discipline, as well as for charting a path for future community efforts. The event concluded with in an interactive panel-led discussion that addressed such topics as integrating efforts between experimental and computational scientists, uncertainty quantification, and identifying the greatest challenges for future workforce preparation. This article is a summary of this discussion and the thoughts presented.

  1. CLINICAL ASSESSMENT OF THE 1/3rd RADIUS USING A NEW DESKTOP ULTRASONIC BONE DENSITOMETER

    PubMed Central

    Stein, Emily M.; Rosete, Fernando; Young, Polly; Kamanda-Kosseh, Mafo; McMahon, Donald J.; Luo, Gangming; Kaufman, Jonathan J.; Shane, Elizabeth; Siffert, Robert S.

    2012-01-01

    The objectives of this study were to evaluate the capability of a novel ultrasound device to clinically estimate bone mineral density (BMD) at the 1/3rd radius. The device rests on a desktop and is portable, and permits real-time evaluation of the radial BMD. The device measures two (2) net time delay (NTD) parameters, NTDDW and NTDCW. NTDDW is defined as the difference between the transit time of an ultrasound pulse to travel through soft-tissue, cortex and medullary cavity, and the transit time through soft tissue only of equal overall distance. NTDCW is defined as the difference between the transit time of an ultrasound pulse to travel through soft-tissue and cortex only, and the transit time through soft tissue only again of equal overall distance. The square root of the product of these two parameters is a measure of the radial BMD at the 1/3rd location as measured by dual-energy x-ray absorptiometry (DXA). A clinical IRB-approved study measured ultrasonically sixty adults at the 1/3rd radius. BMD was also measured at the same anatomical site and time using DXA. A linear regression using NTD produced a linear correlation coefficient of 0.93 (P<0.001). These results are consistent with previously reported simulation and in vitro studies. In conclusion, although x-ray methods are effective in bone mass assessment, osteoporosis remains one of the largest undiagnosed and under-diagnosed diseases in the world today. The research described here should enable significant expansion of diagnosis and monitoring of osteoporosis through a desktop device that ultrasonically assesses bone mass at the 1/3rd radius. PMID:23312957

  2. 3rd Workshop on Semantic Ambient Media Experience (SAME) - In Conjunction with AmI-2010

    NASA Astrophysics Data System (ADS)

    Lugmayr, Artur; Stockleben, Bjoern; Kaario, Juha; Pogorelc, Bogdan; Risse, Thomas

    The SAME workshop takes place for the 3rd time in 2010, and it's theme in this year was creating the business value-creation, vision, media theories and technology for ambient media. SAME differs from other workshops due to its interactive and creative touch and going beyond simple powerpoint presentations. Several results will be published by AMEA - the AMbient Media Association (www.ambientmediaassociation.org.

  3. The Goodrich 3rd generation DB-110 system: successful flight test on the F-16 aircraft

    NASA Astrophysics Data System (ADS)

    Lange, Davis; Iyengar, Mrinal; Maver, Larry; Dyer, Gavin; Francis, John

    2007-04-01

    The 3rd Generation Goodrich DB-110 system provides users with a three (3) field-of-view high performance Airborne Reconnaissance capability that incorporates a dual-band day and nighttime imaging sensor, a real time recording and a real time data transmission capability to support long range, medium range, and short range standoff and over-flight mission scenarios, all within a single pod. Goodrich developed their 3rd Generation Airborne Reconnaissance Pod for operation on a range of aircraft types including F-16, F-15, F-18, Euro-fighter and older aircraft such as the F-4, F-111, Mirage and Tornado. This system upgrades the existing, operationally proven, 2nd generation DB-110 design with enhancements in sensor resolution, flight envelope and other performance improvements. Goodrich recently flight tested their 3rd Generation Reconnaissance System on a Block 52 F-16 aircraft with first flight success and excellent results. This paper presents key highlights of the system and presents imaging results from flight test.

  4. Recent advances on developing 3rd generation enzyme electrode for biosensor applications.

    PubMed

    Das, Priyanki; Das, Madhuri; Chinnadayyala, Somasekhar R; Singha, Irom Manoj; Goswami, Pranab

    2016-05-15

    The electrochemical biosensor with enzyme as biorecognition element is traditionally pursued as an attractive research topic owing to their high commercial perspective in healthcare and environmental sectors. The research interest on the subject is sharply increased since the beginning of 21st century primarily, due to the concomitant increase in knowledge in the field of material science. The remarkable effects of many advance materials such as, conductive polymers and nanomaterials, were acknowledged in the developing efficient 3rd generation enzyme bioelectrodes which offer superior selectivity, sensitivity, reagent less detection, and label free fabrication of biosensors. The present review article compiles the major knowledge surfaced on the subject since its inception incorporating the key review and experimental papers published during the last decade which extensively cover the development on the redox enzyme based 3rd generation electrochemical biosensors. The tenet involved in the function of these direct electrochemistry based enzyme electrodes, their characterizations and various strategies reported so far for their development such as, nanofabrication, polymer based and reconstitution approaches are elucidated. In addition, the possible challenges and the future prospects in the development of efficient biosensors following this direct electrochemistry based principle are discussed. A comparative account on the design strategies and critical performance factors involved in the 3rd generation biosensors among some selected prominent works published on the subject during last decade have also been included in a tabular form for ready reference to the readers. PMID:26735873

  5. LPT. Plot plan and site layout. Includes shield test pool/EBOR ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Plot plan and site layout. Includes shield test pool/EBOR facility. (TAN-645 and -646) low power test building (TAN-640 and -641), water storage tanks, guard house (TAN-642), pump house (TAN-644), driveways, well, chlorination building (TAN-643), septic system. Ralph M. Parsons 1229-12 ANP/GE-7-102. November 1956. Approved by INEEL Classification Office for public release. INEEL index code no. 038-0102-00-693-107261 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  6. LPT. Elevations of low power test building (TAN640 and 641). ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    LPT. Elevations of low power test building (TAN-640 and -641). West and south elevations show stepped shield wall. South and east elevations show pumice block passageway on south side. Reactor cell walls are concrete. One-story parts are pumice block. Metal rollup doors. Ralph M. Parsons 1229-12 ANP/GE-7-640-A-2. November 1956. Approved by INEEL Classification Office for public release. INEEL index code no. 038-0640-00-693-107275 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  7. Predictions of misruns using three-phase coupled mold-filling and solidification simulations in low pressure turbine (LPT) blades

    NASA Astrophysics Data System (ADS)

    Jana, S.; Kättlitz, O.; Hediger, F.; Jakumeit, J.; Aguilar, J.

    2012-07-01

    New alloy developments such as γ-TiAl aim at weight reduction and improvement of performance capabilities of aircraft engines. A drawback of TiAl is its low fluidity, which easily leads to misruns during the casting process. In this work a three-phase mold filling and solidification simulation methodology has been established and validated against casting trials. It uses the finite-volume method and arbitrary polyhedral control volumes to solve the governing equations. A High-Resolution Interface-Capturing (HRIC) scheme has been established as state-of-the-art for modeling multiphase flows with sharp interfaces using the so called Volume-of-Fluid (VOF) model. This multiphase model has been extended to casting processes to predict velocity, pressure and temperature distribution for all three phases, namely the gas, melt and solidified phase. Since LPT blades for aircraft engine applications are of widely differing in geometry with less than 1 mm thickness at the trailing edges, the effect of surface tension and wetting angle is dominant in these wall-bounded flows during the filling stage. These effects can only be calculated correctly if the interface between the phases is sharp and mesh quality is high. For the later automatically generated body-fitted polyhedral meshes with thin prism layers are used. In addition resistance of the dendrite network to melt flow must be adequately modeled. Here, an additional source term in the momentum equation based on Kozeny-Carman relation for permeability estimation is used. A detailed analysis of filling and solidification is presented to study the performance of the simulation method.

  8. NURSING EMERGING. ANA Nursing: Scope and Standards of Practice, (2015) 3rd Edition.

    PubMed

    Mariano, Carla

    2016-04-01

    AHNA Past-President Carla Mariano recently had the privilege of serving on the American Nurses Association's (ANA) Nursing Scope and Standards Revision Workgroup. Representing the specialty practice of holistic nursing, Carla's presence within this workgroup contributed greatly to the inclusion of holistic principles and values throughout the new 2015 Nursing: Scope and Standards of Practice, 3rd edition, the foundational document that informs and guides professional nursing practice within the United States. This is a significant step forward for holistic nursing and an indicator of our growing influence as specialty practice. PMID:27305802

  9. Preface to Special Topic: Invited Papers of the 3rd International Conference on Ultrafast Structural Dynamics

    PubMed Central

    Johnson, S. L.

    2016-01-01

    The ability to visualize the real-time dynamics of atomic, magnetic, and electronic structure is widely recognized in many fields as a key element underpinning many important processes in chemistry, materials science, and biology. The need for an improved understanding of such processes becomes acute as energy conversion processes on fast time scales become increasingly relevant to problems in science and technology. This special issue, containing invited papers from participants at the 3rd International Conference on Ultrafast Structural Dynamics held June 10–12, 2015 in Zurich, Switzerland, discusses several recent developments in this area. PMID:27191008

  10. Preface to Special Topic: Invited Papers of the 3rd International Conference on Ultrafast Structural Dynamics.

    PubMed

    Johnson, S L

    2016-03-01

    The ability to visualize the real-time dynamics of atomic, magnetic, and electronic structure is widely recognized in many fields as a key element underpinning many important processes in chemistry, materials science, and biology. The need for an improved understanding of such processes becomes acute as energy conversion processes on fast time scales become increasingly relevant to problems in science and technology. This special issue, containing invited papers from participants at the 3rd International Conference on Ultrafast Structural Dynamics held June 10-12, 2015 in Zurich, Switzerland, discusses several recent developments in this area. PMID:27191008

  11. Overview of the 3rd isirv-Antiviral Group Conference – advances in clinical management

    PubMed Central

    Hurt, Aeron C; Hui, David S; Hay, Alan; Hayden, Frederick G

    2015-01-01

    This review highlights the main points which emerged from the presentations and discussions at the 3rd isirv-Antiviral Group Conference - advances in clinical management. The conference covered emerging and potentially pandemic influenza viruses and discussed novel/pre-licensure therapeutics and currently approved antivirals and vaccines for the control of influenza. Current data on approved and novel treatments for non-influenza respiratory viruses such as MERS-CoV, respiratory syncytial virus (RSV) and rhinoviruses and the challenges of treating immunocompromised patients with respiratory infections was highlighted. PMID:25399715

  12. Treatment of 3rd molar-induced periodontal defects with guided tissue regeneration.

    PubMed

    Oxford, G E; Quintero, G; Stuller, C B; Gher, M E

    1997-07-01

    Recent reports provide evidence of increased attachment levels when using guided tissue regeneration (GTR) techniques for the treatment of periodontal defects. Periodontal defects frequently occur at the distal aspect of mandibular 2nd molars which are next to mesioangular impacted 3rd molars that have oral communication. The purpose of this study was to determine whether the use of GTR can enhance probing attachment levels (PALs) following extraction of mesioangular impacted third molars. 12 patients with bilateral soft tissue impacted mandibular 3rd molars entered this split mouth study. After extractions, the previously exposed distal root surface of the 2nd molars were debrided. The defects on the randomly selected experimental sites were covered with expanded polytetraflouro-ethylene (e-PTFE) membrane and the tissue was replaced to cover the membrane. Membranes were removed after 6 weeks. Control sites were treated identically except no membrane was placed. GI, P1I, PD, PAL and BOP records were obtained at 0, 3 and 6 months. The use of barrier material did not provide statistically-significant differences in PAL when comparing experimental versus control sites. Nevertheless, PAL gain was consistently greater at 3 and 6 months when GTR techniques were used in sites with deep impactions. PMID:9226386

  13. Using food as a tool to teach science to 3rd grade students in Appalachian Ohio

    PubMed Central

    Duffrin, Melani W.; Hovland, Jana; Carraway-Stage, Virginia; McLeod, Sara; Duffrin, Christopher; Phillips, Sharon; Rivera, David; Saum, Diana; Johanson, George; Graham, Annette; Lee, Tammy; Bosse, Michael; Berryman, Darlene

    2010-01-01

    The Food, Math, and Science Teaching Enhancement Resource (FoodMASTER) Initiative is a compilation of programs aimed at using food as a tool to teach mathematics and science. In 2007–2008, a foods curriculum developed by professionals in nutrition and education was implemented in 10 3rd-grade classrooms in Appalachian Ohio; teachers in these classrooms implemented 45 hands-on foods activities that covered 10 food topics. Subjects included measurement; food safety; vegetables; fruits; milk and cheese; meat, poultry, and fish; eggs; fats; grains; and meal management. Students in four other classrooms served as the control group. Mainstream 3rd-grade students were targeted because of their receptiveness to the subject matter, science standards for upper elementary grades, and testing that the students would undergo in 4th grade. Teachers and students alike reported that the hands-on FoodMASTER curriculum experience was worthwhile and enjoyable. Our initial classroom observation indicated that the majority of students, girls and boys included, were very excited about the activities, became increasingly interested in the subject matter of food, and were able to conduct scientific observations. PMID:20975982

  14. Altered differential hemocyte count in 3rd instar larvae of Drosophila melanogaster as a response to chronic exposure of Acephate

    PubMed Central

    Rajak, Prem; Dutta, Moumita

    2015-01-01

    Acephate, an organophosphate (OP) pesticide, was used to investigate the effects of its chronic exposure on hemocyte abundance in a non-target dipteran insect Drosophila melanogaster. For this purpose, six graded concentrations ranging from 1 to 6 μg/ml were selected, which are below the reported residual values (up to 14 μg/ml) of the chemical. 1st instar larvae were fed with these concentrations up to the 3rd instar stage and accordingly hemolymph smears from these larvae were prepared for differential hemocyte count. Three types of cells are found in Drosophila hemolymph, namely, plasmatocytes, lamellocytes and crystal cells. Plasmatocyte count was found to decrease with successive increase in treatment concentrations. Crystal cells showed an increasing trend in their number. Though the number of lamellocytes was very low, a bimodal response was noticed. Lamellocyte number was found to increase with the initial three concentrations, followed by a dose dependent reduction in their number. As hemocytes are directly linked to the immune system of fruit flies, fluctuations in normal titer of these cells may affect insect immunity. Hemocytes share homologies in their origin and mode of action with the immune cells of higher organisms including man. Thus the present findings suggest that immune cells of humans and other organisms may be affected adversely under chronic exposure to Acephate. PMID:27486365

  15. To keep the catch – that is the question: a personal account of the 3rd Annual EULAR Congress, Stockholm

    PubMed Central

    Wollheim, Frank A

    2002-01-01

    The 3rd Annual EULAR Congress, held in Stockholm on 12–15 June 2002, had a turnout of 8300 delegates, almost identical to last year's record attendance level in Prague. The venue was close to ideal, allowing ample space for poster sessions in the exhibition hall. The manned poster sessions were well attended, even on the last day of the Congress. The numerous invited speakers represented the world's elite, allowing the staging of excellent state-of-the-art podium sessions. The aim of attracting the young scientific community was partly achieved, but individual delegates' dependence on industry sponsorship poses potential problems. The organization was a big improvement compared to that of the two previous congresses. Approximately 1800 abstracts were submitted, an increase of 50%, resulting in a higher quality of accepted abstracts. The satellite symposia held every morning and late afternoon were well attended; thus, industry exposure of new products, both in podium sessions and at the exhibitions, was well accommodated. The Annual EULAR Congress consolidates its position as one of the two most important annual congresses of rheumatology, but EULAR economy and commercial aspects are still too dominant in relation to science. PMID:12223107

  16. PREFACE: 3rd International Symposium on Functional Materials 2009 (ISFM 2009) 3rd International Symposium on Functional Materials 2009 (ISFM 2009)

    NASA Astrophysics Data System (ADS)

    Kiwon, Kim; Li, Lu; Taehyun, Nam; Jouhyeon, Ahn

    2010-05-01

    The 3rd International Symposium on Functional Materials 2009 (ISFM 2009) and its preconference, Advances in Functional Materials 2009 (AFM 2009), were successfully held in the Republic of Korea from 15-18 June 2009 and in the People's Republic of China from 8-12 June 2009, respectively. The two conferences attracted over 300 oral and poster presentations from over 12 countries including Australia, Canada, China, Germany, Japan, India, Israel, Korea, The Netherlands, Thailand, the UK and the USA. In the two conferences, eight keynote lectures were delivered by S Miyazaki, S A Akbar, D J Singh, C Suryanarayana, M~Greenblatt, H Zhang, T Sato and J Ding. This topical issue of Physica Scripta contains papers presented at the ISFM 2009 and AFM 2009. Keyan Li from Dalian University, People's Republic of China, presents some empirical formulae to estimate the elastic moduli of rocksalt-, zincblende- and chalcopyrite-structured crystals, on the basis of electronegativities of bonded atoms in the crystallographic frame. Min-Jung Kim from Hanyang University, Korea, reports on the preparation and characterization of carboxyl functionalization of magnetite nanoparticles for oligonucleotide immobilization. F Yan from the National University of Singapore studies the fabrication of Bi(Fe0.5Sc0.5)O3-PbTiO3 (BSF-PT) thin films by pulsed laser deposition, and the enhanced magnetic moment with respect to BiFeO3-PbTiO3. Dong-Gil Lee from Pusan National University, Korea, reports on the sterilization of enteropathogenic Escherichia coli using nanofiber TiO2 films prepared by the electrostatic spray method. Sang-Eun Park from the Korea Institute of Science and Technology reports on the study of encapsulated Fe3O4 nanoparticles with a silica thin layer with a reversible capacity of about 363 mAhg-1. Other researchers report on many other exiting achievements in the fields of ferromagnetic materials, magneto-optical materials, thermoelectric materials, shape memory materials, fuel-cell and

  17. PREFACE: 3rd International Conference of Mechanical Engineering Research (ICMER 2015)

    NASA Astrophysics Data System (ADS)

    Mamat, Riazalman; Rahman, Mustafizur; Mohd. Zuki Nik Mohamed, Nik; Che Ghani, Saiful Anwar; Harun, Wan Sharuzi Wan

    2015-12-01

    The 3rd ICMER2015 is the continuity of the NCMER2010. The year 2010 represents a significant milestone in the history for Faculty of Mechanical Engineering, Universiti Malaysia Pahang (UMP) Malaysia with the organization of the first and second national level conferences (1st and 2nd NCMER) at UMP on May 26-27 and Dec 3-4 2010. The Faculty then changed the name from National Conference on Mechanical Engineering Research (NCMER) to International Conference on Mechanical Engineering Research (ICMER) in 2011 and this year, 2015 is our 3rd ICMER. These proceedings contain the selected scientific manuscripts submitted to the conference. It is with great pleasure to welcome you to the "International Conference on Mechanical Engineering Research (ICMER2015)" that is held at Zenith Hotel, Kuantan, Malaysia. The call for papers attracted submissions of over two hundred abstracts from twelve different countries including Japan, Iran, China, Kuwait, Indonesia, Norway, Philippines, Morocco, Germany, UAE and more. The scientific papers published in these proceedings have been revised and approved by the technical committee of the 3rd ICMER2015. All of the papers exhibit clear, concise, and precise expositions that appeal to a broad international readership interested in mechanical engineering, combustion, metallurgy, materials science as well as in manufacturing and biomechanics. The reports present original ideas or results of general significance supported by clear reasoning and compelling evidence, and employ methods, theories and practices relevant to the research. The authors clearly state the questions and the significance of their research to theory and practice, describe how the research contributes to new knowledge, and provide tables and figures that meaningfully add to the narrative. In this edition of ICMER representatives attending are from academia, industry, governmental and private sectors. The plenary and invited speakers will present, discuss, promote and

  18. Defining a new vision for the retinoblastoma gene: report from the 3rd International Rb Meeting.

    PubMed

    Rubin, Seth M; Sage, Julien

    2013-01-01

    The retinoblastoma tumor suppressor (Rb) pathway is mutated in most, if not all human tumors. In the G0/G1 phase, Rb and its family members p107 and p130 inhibit the E2F family of transcription factors. In response to mitogenic signals, Cyclin-dependent kinases (CDKs) phosphorylate Rb family members, which results in the disruption of complexes between Rb and E2F family members and in the transcription of genes essential for S phase progression. Beyond this role in early cell cycle decisions, Rb family members regulate DNA replication and mitosis, chromatin structure, metabolism, cellular differentiation, and cell death. While the RB pathway has been extensively studied in the past three decades, new investigations continue to provide novel insights into basic mechanisms of cancer development and, beyond cancer, help better understand fundamental cellular processes, from plants to mammals. This meeting report summarizes research presented at the recently held 3rd International Rb Meeting. PMID:24257515

  19. Defining a new vision for the retinoblastoma gene: report from the 3rd International Rb Meeting

    PubMed Central

    2013-01-01

    The retinoblastoma tumor suppressor (Rb) pathway is mutated in most, if not all human tumors. In the G0/G1 phase, Rb and its family members p107 and p130 inhibit the E2F family of transcription factors. In response to mitogenic signals, Cyclin-dependent kinases (CDKs) phosphorylate Rb family members, which results in the disruption of complexes between Rb and E2F family members and in the transcription of genes essential for S phase progression. Beyond this role in early cell cycle decisions, Rb family members regulate DNA replication and mitosis, chromatin structure, metabolism, cellular differentiation, and cell death. While the RB pathway has been extensively studied in the past three decades, new investigations continue to provide novel insights into basic mechanisms of cancer development and, beyond cancer, help better understand fundamental cellular processes, from plants to mammals. This meeting report summarizes research presented at the recently held 3rd International Rb Meeting. PMID:24257515

  20. Dental health in antique population of Vinkovci - Cibalae in Croatia (3rd-5th century).

    PubMed

    Peko, Dunja; Vodanović, Marin

    2016-08-01

    Roman city Cibalae (Vinkovci) - the birthplace of Roman emperors Valentinian I and Valens was a very well developed urban ares in the late antique what was evidenced by numerous archaeological findings. The aim of this paper is to get insight in dental health of antique population of Cibalae. One hundred individuals with 2041 teeth dated to 3rd - 5th century AD have been analyzed for caries, antemortem tooth loss, periapical diseases and tooth wear. Prevalence of antemortem tooth loss was 4.3% in males, 5.2% in females. Prevalence of caries per tooth was 8.4% in males, 7.0% in females. Compared to other Croatian antique sites, ancient inhabitants of Roman Cibalae had rather good dental health with low caries prevalence and no gender differences. Statistically significant difference was found between males in females in the prevalence of periapical lesions and degree of tooth wear. Periapical lesions were found only in males. PMID:27598951

  1. Evaluation of the "Respect Not Risk" firearm safety lesson for 3rd-graders.

    PubMed

    Liller, Karen D; Perrin, Karen; Nearns, Jodi; Pesce, Karen; Crane, Nancy B; Gonzalez, Robin R

    2003-12-01

    The purpose of this study was to evaluate the MORE HEALTH "Respect Not Risk" Firearm Safety Lesson for 3rd-graders in Pinellas County, Florida. Six schools representative of various socioeconomic levels were selected as the test sites. Qualitative and quantitative data were collected. A total of 433 matched pretests/posttests were used to determine the effectiveness of the class in increasing student knowledge about firearm safety. The results revealed a significant increase in the mean scores on the posttest compared with the pretest. Qualitative findings showed the lesson was positively received by both students and teachers, and 65% of responding students reported discussing the lesson with family members. School nurses are encouraged to take a leading role in promoting firearm injury prevention to students. PMID:14622039

  2. Passive solar progress: a simplified guide to the 3rd national passive solar conference

    SciTech Connect

    Miller, H.; Howell, Y.; Richards, D.

    1980-10-01

    Some of the concepts and practices that have come to be known as passive solar heating and cooling are introduced, and a current picture of the field is presented. Much of the material presented is derived from papers given at the 3rd National Passive Solar Conference held in San Jose, California in January 1979 and sponsored by the US Department of Energy. Extracts and data from these papers have been integrated in the text with explanatory and descriptive material. In this way, it is attempted to present technical information in an introductory context. Topics include design considerations, passive and hybrid systems and applications, sizing methods and performance prediction, and implementation issues. A glossary is included. (WHK)

  3. John D. Rockefeller 3rd, statesman and founder of the Population Council.

    PubMed

    Dunlop, J

    2000-01-01

    This article presents a profile of John D. Rockefeller 3rd, statesman and founder of the Population Council. It is noted that Rockefeller took a broad view of population control as a means to address poverty and economic development rather than as an end in itself. In 1952 he initiated the convocation of the Conference on Population Problems held in Williamsburg, Virginia. The discussion focused on food supply, industrial development, depletion of natural resources, and political instability resulting from unchecked population growth. In 1967, Rockefeller initiated, lobbied for, and finally achieved a World Leaders' Statement signed by 30 heads of state including US President Lyndon Johnson. The document drew attention to population growth as a world problem and engendered political support for family planning as a solution. After 3 years the Commission on Population Growth and the American Future was established, and Rockefeller was made its chairman. Several issues were debated, including more safer fertility control and the legalization of abortion. PMID:12349764

  4. Experimental measurements in a highly loaded low pressure turbine stage

    NASA Astrophysics Data System (ADS)

    Schmitz, John Thomas

    The performance and detailed flow physics of a transonic, low-pressure turbine (LPT) stage with design Zw=1.35, DeltahT/ U2 = 2.8, φ = 0.78, and eta = 90.5% has been investigated experimentally. Recent developments in boundary layer transition modeling were utilized in the aerodynamic design of the stage. Measurements were acquired in a recently developed, high-speed turbine facility constructed to investigate the effects that Reynolds number, nozzle exit flow, freestream turbulence, vane-blade spacing, and rim seal flows have on the loss generating mechanisms of a highly loaded LPT stage. Flow control techniques were applied at the stage inlet with the intent of reducing a source of stage losses. A research dissertation designed to provide understanding of the loss mechanisms that reduce the effectiveness of the Notre Dame Highly Loaded Turbine Stage 01 (ND-HiLT01) is described.

  5. Transient Growth Theory Prediction of Optimal Placing of Passive and Active Flow Control Devices for Separation Delay in LPT Airfoils

    NASA Technical Reports Server (NTRS)

    Tumin, Anatoli; Ashpis, David E.

    2003-01-01

    An analysis of the non-modal growth of perturbations in a boundary layer in the presence of a streamwise pressure gradient is presented. The analysis is based on PSE equations for an incompressible fluid. Examples with Falkner-Skan profiles indicate that a favorable pressure gradient decreases the non-modal growth while an unfavorable pressure gradient leads to an increase of the amplification. It is suggested that the transient growth mechanism be utilized to choose optimal parameters of tripping elements on a low-pressure turbine (LPT) airfoil. As an example, a boundary layer flow with a streamwise pressure gradient corresponding to the pressure distribution over a LPT airfoil is considered. It is shown that there is an optimal spacing of the tripping elements and that the transient growth effect depends on the starting point. At very low Reynolds numbers, there is a possibility to enhance the transient energy growth by means of wall cooling.

  6. The 3^rd International Conference on Women in Physics: Global Perspectives, Common Concerns, Worldwide Views

    NASA Astrophysics Data System (ADS)

    Zastavker, Yevgeniya V.

    2009-03-01

    The 3^rd International Conference on Women in Physics (ICWIP), held in Seoul, Korea, in October 2008, brought together 300 participants from 57 countries, including a diverse 22-member U.S. Delegation, for a 3-day summit of stimulating discussions, thought-provoking presentations, inspirational posters, and networking. Held under the auspices of the Working Group on Women in Physics of the International Union of Pure and Applied Physics (IUPAP), this meeting built on the successes of the 1^st (Paris, 2002) and 2^nd (Rio de Janeiro, 2005) Conferences and further clarified the importance of diversifying the field of physics worldwide. Although considerable progress has been made since 2002, it was clear that the global scientific workforce is still under-utilizing a large percentage of the available female talent pool. If human society is to benefit to its fullest from various contributions that the field of physics can offer in addressing global issues of economic crisis, energy, environment, water, health, poverty, and hunger, women of all races and nationalities need to become fully included and engaged in the national and international physical community. To address these and many other issues, the ICWIP unanimously approved a five-part resolution to IUPAP recommending actions to promote the recruitment, retention, and advancement of women in physics and related fields.

  7. Effects of notetaking instruction on 3rd grade student's science learning and notetaking behavior

    NASA Astrophysics Data System (ADS)

    Lee, Pai-Lin

    The research examined effects of notetaking instruction on elementary-aged students' ability to recall science information and notetaking behavior. Classes of 3rd grade students were randomly assigned to three treatment conditions, strategic notetaking, partial strategic notetaking, and control, for 4 training sessions. The effects of the notetaking instruction were measured by their performances on a test on science information taught during the training, a long-term free recall of the information, and number of information units recalled with or without cues. Students' prior science achievement was used to group students into two levels (high vs. low) and functioned as another independent variable in analysis. Results indicated significant treatment effect on cued and non-cued recall of the information units in favor of the strategy instruction groups. Students with higher prior achievement in science performed better on cued recall and long-term free recall of information. The results suggest that students as young as at the third grade can be instructed to develop the ability of notetaking that promotes their learning.

  8. Resurgence of duckweed research and applications: report from the 3rd International Duckweed Conference.

    PubMed

    Appenroth, Klaus-J; Sree, K Sowjanya; Fakhoorian, Tamra; Lam, Eric

    2015-12-01

    Duckweed, flowering plants in the Lemnaceae family, comprises the smallest angiosperms in the plant kingdom. They have some of the fastest biomass accumulation rates reported to date for plants and have the demonstrated ability to thrive on wastewater rich in dissolved organic compounds and thus could help to remediated polluted water resources and prevents eutrophication. With a high quality genome sequence now available and increased commercial interest worldwide to develop duckweed biomass for renewables such as protein and fuel, the 3rd International Duckweed Conference convened at Kyoto, Japan, in July of 2015, to update the community of duckweed researchers and developers on the progress in the field. In addition to sharing results and ideas, the conference also provided ample opportunities for new-comers as well as established workers in the field to network and create new aliances. We hope this meeting summary will also help to disseminate the key advances and observations that have been presented in this conference to the broader plant biology community in order to encourage increased cross-fertilization of ideas and technologies. PMID:26506824

  9. Measuring the cascade rate in anisotropic turbulence through 3rd order structure functions.

    NASA Astrophysics Data System (ADS)

    Verdini, Andrea; Landi, Simone; Hellinger, Petr

    2014-05-01

    We employ the Von-Karman-Howart-Yaglom-Politano-Poquet (KHYPP)law, to compute the cascade rate by means of 3rd order structure functions in homogeneous, forced, DNS at high resolution. We consider first the isotropic case (no guide field) and verify that the cascade rate is consistent with the dissipation rate. Then we consider an anisotropic case (with guide field) for which the isotropic KHYPP law does not apply. We compute the parallel and perpendicular cascade rates and find that the latter basically accounts for the total dissipation rate, as expected for anisotropic turbulence. Also, the cascade rate derived from the isotropic law is found to be a good approximation for the total cascade rate. Recent works have shown that the hypothesis of stationary turbulence must be probably relaxed in the solar wind. We present preliminary results on the measure of the cascade rate in the expanding solar wind, obtained with DNS of MHD turbulence in the expanding box model. Such model incorporates the basic physic of expansion thus inducing anisotropies driven by both the magnetic field and expansion, along with an energy decrease due to the conservation of linear invariants (angular momentum and magnetic flux). The correction due to non-stationary conditions is found to be important and to become negligible only at small scales, thus suggesting that solar wind measurements over- estimate the actual cascade rate.

  10. Visual, Critical, and Scientific Thinking Dispositions in a 3rd Grade Science Classroom

    NASA Astrophysics Data System (ADS)

    Foss, Stacy

    Many American students leave school without the required 21st century critical thinking skills. This qualitative case study, based on the theoretical concepts of Facione, Arheim, and Vygotsky, explored the development of thinking dispositions through the arts in science on the development of scientific thinking skills when used as a conceptual thinking routine in a rural 3rd grade classroom. Research questions examined the disposition to think critically through the arts in science and focused on the perceptions and experiences of 25 students with the Visual Thinking Strategy (VTS) process. Data were collected from classroom observations (n = 10), student interviews (n = 25), teacher interviews ( n = 1), a focus group discussion (n = 3), and artifacts of student work (n = 25); these data included perceptions of VTS, school culture, and classroom characteristics. An inductive analysis of qualitative data resulted in several emergent themes regarding disposition development and students generating questions while increasing affective motivation. The most prevalent dispositions were open-mindedness, the truth-seeking disposition, the analytical disposition, and the systematicity disposition. The findings about the teachers indicated that VTS questions in science supported "gradual release of responsibility", the internalization of process skills and vocabulary, and argumentation. This case study offers descriptive research that links visual arts inquiry and the development of critical thinking dispositions in science at the elementary level. A science curriculum could be developed, that emphasizes the development of thinking dispositions through the arts in science, which in turn, could impact the professional development of teachers and learning outcomes for students.

  11. SESAME, A 3rd Generation Synchrotron Light Source for the Middle East

    SciTech Connect

    Einfeld, D.; Hasnain, S.S.; Sayers, Z.; Schopper, H.; Winick, H.; Al-Dmour, E.

    2004-05-12

    Developed under the auspices of UNESCO, SESAME (Synchrotron-light for Experimental Science and Applications in the Middle East) will be a major international research centre in the Middle East and Mediterranean region. On 6th of January 2003, the official foundation of SESAME took place. The facility is located in Allan, Jordan, 30 km North-West of Amman. As of August 2003 the Founding Members are Bahrain, Egypt, Iran, Israel, Jordan, Pakistan, Palestine, Turkey and United Arabic Emirates, representing a population of over 300 million. SESAME will be a 2.5 GeV 3rd Generation light source (emittance 24.6 nm.rad, circumference {approx}125m). About 40% of the circumference is available for insertion devices (average length 2.75m) in 13 straight sections. Beam lines are up to 36m. The site and a building are provided by Jordan. Construction started in August 2003. The scientific program will start with up to 6 beam lines: MAD Protein Crystallography, SAXS and WAXS for polymers and proteins, Powder Diffraction for material science, UV/VUV/SXR Photoelectron Spectroscopy and Photoabsorption Spectroscopy, IR Spectroscopy, and EXAFS.

  12. Albion: cost-effective 3rd generation high-performance thermal imaging in the UK

    NASA Astrophysics Data System (ADS)

    McEwen, R. K.; Lupton, M.; Lawrence, M.; Knowles, P.; Wilson, M.; Dennis, P. N. J.; Gordon, N. T.; Lees, D. J.; Parsons, J. F.

    2006-09-01

    The first generation of high performance thermal imaging sensors in the UK was based on two axis opto-mechanical scanning systems and small (4-16 element) arrays of the SPRITE detector, developed during the 1970s. Almost two decades later, a 2nd Generation system, STAIRS C was introduced, based on single axis scanning and a long linear array of approximately 3000 elements. This paper addresses the development of the UK's 3rd Generation High Performance Thermal Imaging sensor systems, under a programme known as "Albion". Three new high performance detectors, manufactured in cadmium mercury telluride, operating in both MWIR and LWIR, providing high resolution and sensitivities without need for opto-mechanical scanning systems will be described. The CMT material is grown by MOVPE on low cost substrates and bump bonded to the silicon read out circuit (ROIC). All three detectors are designed to fit with existing standard Integrated Detector Cooling Assemblies (IDCAs). The two largest detectors will be integrated with field demonstrator cameras providing MWIR and LWIR solutions that can rapidly be tailored to specific military requirements. The remaining detector will be a LWIR device with a smart ROIC, facilitating integration times much longer than can typically be achieved with focal plane arrays and consequently yield very high thermal sensitivity. This device will be demonstrated in a lab based camera system.

  13. Albion: the UK 3rd generation high-performance thermal imaging programme

    NASA Astrophysics Data System (ADS)

    McEwen, R. K.; Lupton, M.; Lawrence, M.; Knowles, P.; Wilson, M.; Dennis, P. N. J.; Gordon, N. T.; Lees, D. J.; Parsons, J. F.

    2007-04-01

    The first generation of high performance thermal imaging sensors in the UK was based on two axis opto-mechanical scanning systems and small (4-16 element) arrays of the SPRITE detector, developed during the 1970s. Almost two decades later, a 2nd Generation system, STAIRS C was introduced, based on single axis scanning and a long linear array of approximately 3000 elements. The UK has now begun the industrialisation of 3 rd Generation High Performance Thermal Imaging under a programme known as "Albion". Three new high performance cadmium mercury telluride arrays are being manufactured. The CMT material is grown by MOVPE on low cost substrates and bump bonded to the silicon read out circuit (ROIC). To maintain low production costs, all three detectors are designed to fit with existing standard Integrated Detector Cooling Assemblies (IDCAs). The two largest focal planes are conventional devices operating in the MWIR and LWIR spectral bands. A smaller format LWIR device is also described which has a smart ROIC, enabling much longer stare times than are feasible with conventional pixel circuits, thus achieving very high sensitivity. A new reference surface technology for thermal imaging sensors is described, based on Negative Luminescence (NL), which offers several advantages over conventional peltier references, improving the quality of the Non-Uniformity Correction (NUC) algorithms.

  14. SESAME-A 3rd Generation Synchrotron Light Source for the Middle East

    NASA Astrophysics Data System (ADS)

    Winick, Herman

    2010-02-01

    Developed under the auspices of UNESCO and modeled on CERN, SESAME (Synchrotron-light for Experimental Science and Applications in the Middle East) is an international research center in construction in Jordan. It will enable world class research by scientists from the region, reversing the brain drain. It will also build bridges between diverse societies, contributing to a culture of peace through international cooperation in science. The centerpiece is a synchrotron light source originating from BESSY I, a gift by Germany. The upgraded machine, a 2.5 GeV 3rd Generation Light Source (133m circumference, 26nm-rad emittance and 12 places for insertion devices), will provide light from infra-red to hard X-rays, offering excellent opportunities to train local scientists and attract those working abroad to return. The SESAME Council meets twice each year and presently has nine Members (Bahrain, Cyprus, Egypt, Iran, Israel, Jordan, Pakistan, Palestinian Authority, Turkey). Members have responsibility for the project and provide the annual operations budget (1.5M US dollars in 2009, expected to rise to about 5M when operation starts in 2012-13). Jordan provided the site, building, and infrastructure. A staff of 20 is installing the 0.8 GeV BESSY I injection system. The facility will have the capacity to serve 30 or more experiments operating simultaneously. See www.sesame.org.jo )

  15. Report from the 3rd AIDS Impact Conference: culture, community, empowerment.

    PubMed

    Aggleton, P

    1997-10-01

    Presentations made at the 3rd AIDS Impact Conferences in June 1997 in Melbourne, Australia are summarized. The presentations focused on the importance of local beliefs, practices, and sexual cultures as factors that impact HIV risk. The three dominant themes of this conference were a concern for community, an emphasis on culture, and empowerment for the most vulnerable groups. Speakers illustrated the importance of culture as a factor in the form, context, and meaning of sex among young men and women in Thailand, Australia, Italy, Cambodia, and the United States. Studies conducted in correctional facilities illustrate how the culture of sex and substance use can intensify the HIV risk. Papers examined the sexual revolution in China and the experiences of indigenous people in Brazil, Australia, and New Zealand. The presentations also highlighted drug use cultures among gay men in Australian and German cities and introduced new research methodologies for the analysis of these processes and issues. The closing presentation considered the politics of HIV and their relationship to national and international processes of negative societal responses to HIV diseases. PMID:11364796

  16. PREFACE: 3rd International Conference on Manufacturing, Optimization, Industrial and Material Engineering (MOIME 2015)

    NASA Astrophysics Data System (ADS)

    Lumban Gaol, Ford; Webb, Jeff; Ding, Jun

    2015-05-01

    The 3rd International Conference on Manufacturing, Optimization, Industrial and Material Engineering (MOIME 2015) was held at the Sheraton Kuta, Bali, Indonesia, from 28 - 29 March 2015. The MOIME 2015 conference is aimed to bring together researchers, engineers and scientists in the domain of interest from around the world. MOIME 2015 is placed on promoting interaction between the theoretical, experimental, and applied communities, so that a high level exchange is achieved in new and emerging areas within Material Engineering, Industrial Engineering and all areas that relate to Optimization. We would like to express our sincere gratitude to all in the Technical Program Committee who have reviewed the papers and developed a very interesting Conference Program, as well as the invited and plenary speakers. This year, we received 99 papers and after rigorous review, 24 papers were accepted. The participants come from eight countries. There were four parallel sessions and two invited speakers. It is an honour to present this volume of IOP Conference Series: Materials Science and Engineering (MSE) and we deeply thank the authors for their enthusiastic and high-grade contributions. Finally, we would like to thank the conference chairmen, the members of the steering committee, the organizing committee, the organizing secretariat and the financial support from the conference sponsors that allowed the success of MOIME 2015. The Editors of the MOIME 2015 Proceedings Dr. Ford Lumban Gaol Jeff Webb, Ph.D Prof. Jun DING, Ph.D

  17. Effect of 3rd-degree gravity harmonics and Earth perturbations on lunar artificial satellite orbits

    NASA Astrophysics Data System (ADS)

    Tzirti, S.; Tsiganis, K.; Varvoglis, H.

    2010-12-01

    In a previous work we studied the effects of (I) the J 2 and C 22 terms of the lunar potential and (II) the rotation of the primary on the critical inclination orbits of artificial satellites. Here, we show that, when 3rd-degree gravity harmonics are taken into account, the long-term orbital behavior and stability are strongly affected, especially for a non-rotating central body, where chaotic or collision orbits dominate the phase space. In the rotating case these phenomena are strongly weakened and the motion is mostly regular. When the averaged effect of the Earth’s perturbation is added, chaotic regions appear again for some inclination ranges. These are more important for higher values of semi-major axes. We compute the main families of periodic orbits, which are shown to emanate from the ‘frozen eccentricity’ and ‘critical inclination’ solutions of the axisymmetric problem (‘ J 2 + J 3’). Although the geometrical properties of the orbits are not preserved, we find that the variations in e, I and g can be quite small, so that they can be of practical importance to mission planning.

  18. Measurement and correction of the 3rd order resonance in the Tevatron

    SciTech Connect

    Schmidt, F.; Alexahin, Y.; Lebedev, V.; Still, D.; Valishev, A.; /Fermilab

    2006-06-01

    At Fermilab Tevatron BPM system has been recently upgraded resulting much better accuracy of beam position measurements and improvements of data acquisition for turn-by-turn measurements. That allows one to record the beam position at each turn for 8000 turns for all BPMs (118 in each plane) with accuracy of about 10-20 {micro}m. In the last decade a harmonic analysis tool has been developed at CERN that allows relating each FFT line derived from the BPM data with a particular non-linear resonance in the machine. In fact, one can even detect the longitudinal position of the sources of these resonances. Experiments have been performed at the Tevatron in which beams have been kicked to various amplitudes to analyze the 3rd order resonance. It was possible to address this rather large resonance to some regular machine sextupoles. An alternative sextupole scheme allowed the suppression of this resonance by a good factor of 2. Lastly, the experimental data are compared with model calculations.

  19. New half-film method for measuring Al2O3 film MTF of 3rd generation image intensifier

    NASA Astrophysics Data System (ADS)

    Cheng, Yaojin; Shi, Feng; Bai, Xiaofeng; Zhu, Yufeng; Yan, Lei; Liu, Feng; Li, Min

    2012-10-01

    In 3rd generation image intensifier, Al2O3 film on the input of MCP is a serious influence factor on device MTF due to its electron scattering process. There are no reportes about how to measure the MTF of Al2O3 film. In this paper a new Half-film comparssion test method is creatively established for determing the film MTF, which overcomes the difficulty of measuring super thin film less than a few nm. In this way, the MTF curves of 10nm Al2O3 film can be accurately obtained. The measurement results show that 10nm Al2O3 film obviously decay the MTF performance of the 3rd generation image intensifier and take an important role in the improvement work of 3rd generation image intensifier MTF and resolution performances.

  20. The Power of PreK-3rd: How a Small Foundation Helped Push Washington State to the Forefront of the PreK-3rd Movement. FCD Case Study

    ERIC Educational Resources Information Center

    Nyhan, Paul

    2011-01-01

    The New School Foundation was not born from a commission, legislative mandate, research project, think tank, or even the mind of a leading education scholar. One of Washington state's pioneering PreK-3rd initiatives began as the brainchild of a wealthy Seattle businessman, Stuart Sloan, 20 years ago. The New School Foundation and its ideas were…

  1. 3rd hand smoking; heterogeneous oxidation of nicotine and secondary aerosol formation in the indoor environment

    NASA Astrophysics Data System (ADS)

    Petrick, Lauren; Dubowski, Yael

    2010-05-01

    Tobacco smoking is well known as a significant source of primary indoor air pollutants. However, only recently has it been recognized that the impact of Tobacco smoking may continue even after the cigarette has been extinguished (i.e., third hand smoke) due to the effect of indoor surfaces. These surfaces may affect the fate of tobacco smoke in the form of secondary reactions and pollutants, including secondary organic aerosol (SOA) formation. Fourier Transform Infrared spectrometry with Attenuated Total Reflection (FTIR-ATR) in tandem with a Scanning Mobility Particle Sizing (SMPS) system was used to monitor the ozonation of cellulose sorbed nicotine and resulting SOA formation. SOA formation began at onset of ozone introduction ([O3] = 60 ± 5 ppb) with a size distribution of dp ≤ 25 nm, and was determined to be a result of heterogeneous reaction (opposed to homogeneous). SOA yield from reacted surface nicotine was on the order of 10 %. Simultaneous to SOA monitoring, FTIR-ATR spectra showed surface changes in the nicotine film as the reaction progressed, revealing a pseudo first-order surface reaction rate of 0.0026 ± 0.0008 min-1. Identified surface oxidation products included: cotinine, myosmine, methylnicotinamide and nicotyrine. Surface reaction rate was found to be partially inhibited at high relative humidity. Given the toxicity of some of the identified products (e.g., cotinine has shown potential mutagenicity and teratogenicity) and that small particles may contribute to adverse health effects, the present study indicates that exposure to 3rd hand smoke ozonation products may pose additional health risks.

  2. Catalysis in the 3rd Dimension: How Organic Molecules May be Formed

    NASA Technical Reports Server (NTRS)

    Freund, Friedemann; DeVincenzi, D. (Technical Monitor)

    2001-01-01

    Catalysis is often little more than a word to phenomenologically describe the fact that a reaction follows a pat1 that leads to products of an unexpected kind or of unexpected yield. Low activation energy barriers for intermediates are recognized as the most likely cause why a system deviates from the thermodynamic pull towards minimizing its free energy and ends up in a metastable state. Seldom is the mechanism known. This i: particularly true for heterogeneous catalysis under hydrothermal conditions with minerals as catalysts. It is commonly assumed that catalytic action takes place across solid-fluid interfaces and that, on the atomic level, interfaces are just 2-dimensional contacts. This makes it difficult to understand, for instance, the assembly of long-chain carboxylic (fatty) acids. 3y studying single crystals that grew from a melt in the presence of H2O and CO2, we can show: (1) that numerals take up the fluid components into solid solution, (2) that some-thing happens converting them to -educedH and C, (3) that C atoms segregate into dislocations and tie C-C bonds. The products are medium-to-long chain Cn protomolecules, with some C-H attached, pre-assembled in the dislocations. Upon solvent extraction, these proto-molecules turn into carboxylic and dicarboxylic acids. This observation suggests that, in a very elementary step, catalysis under hydrothermal conditions leading to fatty acids involves the pre-assembly of Cn entities in the interface that is not 2-D but extends into the 3rd dimension, with dislocations as synthesis sites.

  3. PREFACE: 3rd International Youth Conference "Interdisciplinary Problems of Nanotechnology, Biomedicine and Nanotoxicology" (Nanobiotech 2015)

    NASA Astrophysics Data System (ADS)

    Refsnes, Magne, Prof; Gusev, Alexander, Dr; Godymchuk, Anna, Dr; Bogdan, Anna

    2015-11-01

    The 3rd International Youth Conference "Interdisciplinary Problems of Nanotechnology, Biomedicine and Nanotoxicology" (Nanobiotech2015) was held on 21-22 May 2015 in Tambov, Russia, and was jointly organized by Tambov Derzhavin State University (Russia), the Norwegian Institute of Public Health (Norway), the National University of Science and Technology MISiS (Russia), Tomsk Polytechnic University (Russia) and Tomsk State University. The conference gathered experienced and young researchers, post-docs and students, working in the fieldof nanotechnologies, nanomedicine, nano(eco)toxicology and risk assessment of nanomaterials, in order to facilitate the aggregation and sharing of interests and results for better collaboration and visibility of activity. The goal of Nanobiotech2015 was to bring researchers and practitioners together to share the latest knowledge on nanotechnology-specific risks to occupational and environmental health and assessing how to reduce these potential risks. The main objective of the conference is to identify, systematize and solve current scientific problems inthe sphere of nanobiotechnologies, nanomedicine and nanotoxicology, in order to join forces todetermine prospective areas and compose working groups of interested co-workers for carrying out interdisciplinary research projects. The topics of Nanobiotech2015 were: (1) Nanotechnologies in pharmaceutics and medicine; (2) Sources and mechanisms of nanoparticle release into the environment; (3) Ecological and biological effects of nanoparticles; (4) (Eco)toxicology of nanomaterials; (5) Methods for detection of nanoparticles in the environment and in biological objects; and (6) Physico-chemical properties of nanoparticles in the environment. We want to thank the Organizing Committee, the universities and sponsors supporting the conference,and everyone who contributed to the organization of this meeting, for their contribution towards the conference and for their contributions to these

  4. [3rd generation's TKI in lung cancer non-small cell EGFR-mutated having acquired a secondary T790M resistance].

    PubMed

    Brosseau, Solenn; Viala, Marie; Varga, Andréa; Planchard, David; Besse, Benjamin; Soria, Jean-Charles

    2015-09-01

    Activating EGFR mutations discovery and efficacy of 1st generation tyrosine kinase inhibitors (TKI), such as erlotinib or gefitinib, inaugurated the beginning of personalized medicine in the treatment of EGFR-mutated non-small cell lung cancer (NSCLC). However, all patients showed a tumor progression of 10 to 16 months after the onset of TKI therapy related to molecular resistance mechanisms as T790M mutation. Till now, patients suffering from EGFR-mutated NSCLC with acquired resistance have conventional treatment options. Two new 3rd generations' TKI, AZD9291 and rociletinib, are currently being studied in phases 1-3 studies. Preliminary results show relevant therapeutic properties in patients with T790M mutated-EGFR NSCLC. This review aims to highlight these new molecules, their effectiveness and their clinical toxicities in the treatment of advanced stages of NSCLC expressing the T790M mutation. PMID:26235419

  5. Test Review: C. Keith Conners "Conners 3rd Edition" Toronto, Ontario, Canada--Multi-Health Systems, 2008

    ERIC Educational Resources Information Center

    Kao, Grace S.; Thomas, Hillary M.

    2010-01-01

    "Conners 3rd Edition" is the most updated version of a series of measures for assessing attention deficit hyperactivity disorder (ADHD) and common comorbid problems/disorders in children and adolescents ranging from 6 to 18 years of age. Related problems that the test helps assess include executive dysfunction, learning problems, aggression, and…

  6. Exemplary Institute. Proceedings of the Annual Conference (3rd, Albuquerque, New Mexico, February 22-24, 1998).

    ERIC Educational Resources Information Center

    Native American Scholarship Fund, Inc., Albuquerque, NM.

    This proceedings contains presentations and workshop summaries from the 3rd Annual Exemplary Institute for educators of Native American students. Presentations include: "Quality in Learning: Romancing the Journey" (quality management at Mount Edgecumbe High School, Alaska) (Todd Bergman); "Creating a School-wide Literacy Climate" (Sig Boloz); "How…

  7. Constancy and Variability: Dialogic Literacy Events as Sites for Improvisation in Two 3rd-Grade Classrooms

    ERIC Educational Resources Information Center

    Jordan, Michelle E.; Santori, Diane

    2015-01-01

    This multisite study investigates dialogic literacy events that revolved around narrative and informational texts in two 3rd-grade classrooms. The authors offer a metaphor of musical improvisation to contemplate dialogic literacy events as part of the repertoire of teaching and learning experiences. In literacy learning, where there is much…

  8. 3rd Annual PIALA Conference Saipan--Collecting, Preserving & Sharing Information in Micronesia. Conference Proceedings. October 13-15, 1993.

    ERIC Educational Resources Information Center

    Edmundson, Margaret, Ed.

    1993-01-01

    This PIALA 1993 Proceedings contains many of the papers presented at the 3rd annual conference of the Pacific Islands Association of Libraries and Archives. This publication is the first time papers from this Micronesian regional library and archives conference have ever been published. The conference addressed various topics of interest to…

  9. Predicting 3rd Grade and 10th Grade FCAT Success for 2007-08. Research Brief. Volume 0702

    ERIC Educational Resources Information Center

    Froman, Terry; Rubiera, Vilma

    2008-01-01

    For the past few years the Florida School Code has set the Florida Comprehensive Assessment Test (FCAT) performance requirements for promotion of 3rd graders and graduation for 10 graders. Grade 3 students who do not score at level 2 or higher on the FCAT SSS Reading must be retained unless exempted for special circumstances. Grade 10 students…

  10. Predicting 3rd Grade and 10th Grade FCAT Success for 2006-07. Research Brief. Volume 0601

    ERIC Educational Resources Information Center

    Froman, Terry; Rubiera, Vilma

    2006-01-01

    For the past few years the Florida School Code has set the Florida Comprehensive Assessment Test (FCAT) performance requirements for promotion of 3rd graders and graduation for 10th graders. Grade 3 students who do not score at level 2 or higher on the FCAT SSS Reading must be retained unless exempted for special circumstances. Grade 10 students…

  11. The Lived Experiences of 3rd Generation and beyond U.S.-Born Mexican Heritage College Students: A Qualitative Study

    ERIC Educational Resources Information Center

    Galvan, Richard

    2011-01-01

    The purpose of this study was to describe the psychosocial and identity challenges of 3rd generation and beyond U.S.-born (3GAB-USB) Mexican heritage college students. Alvarez (1973) has written about the psychosocial impact "hybridity" can have on a U.S.- born (USB) Mexican individual who incorporates two distinct cultures (American and Mexican)…

  12. Iowa Acceleration Scale Manual: A Guide for Whole-Grade Acceleration K-8. (3rd Edition, Manual)

    ERIC Educational Resources Information Center

    Assouline, Susan G.; Colangelo, Nicholas; Lupkowski-Shoplik, Ann; Forstadt, Leslie; Lipscomb, Jonathon

    2009-01-01

    Feedback from years of nationwide use has resulted in a 3rd Edition of this unique, systematic, and objective guide to considering and implementing academic acceleration. Developed and tested by the Belin-Blank Center at the University of Iowa, the IAS ensures that acceleration decisions are systematic, thoughtful, well reasoned, and defensible.…

  13. Visual Arts Teaching in Kindergarten through 3rd-Grade Classrooms in the UAE: Teacher Profiles, Perceptions, and Practices

    ERIC Educational Resources Information Center

    Buldu, Mehmet; Shaban, Mohamed S.

    2010-01-01

    This study portrayed a picture of kindergarten through 3rd-grade teachers who teach visual arts, their perceptions of the value of visual arts, their visual arts teaching practices, visual arts experiences provided to young learners in school, and major factors and/or influences that affect their teaching of visual arts. The sample for this study…

  14. Iron metabolism in African American women during the 2nd and 3rd trimester of a high-risk pregnancy

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Objective: To examine iron metabolism during the 2nd and 3rd trimester in African American women classified as a high-risk pregnancy. Design: Longitudinal. Setting: Large, university-based, urban Midwestern medical center. Participants: Convenience sample of 47 African American women classified a...

  15. FOREWORD: 3rd Symposium on Large TPCs for Low Energy Event Detection

    NASA Astrophysics Data System (ADS)

    Irastorza, Igor G.; Colas, Paul; Gorodetzky, Phillippe

    2007-05-01

    organization of the Symposium was made possible by the contribution of the members of the organizating Committee and International Advisory Committee. I want to thank in particular the session chairmen, G. Wormser, S. Katsanevas, J. Timmermans, S. Andriamonje, G. Chardin, T. Ebisuzaki, J.-E. Augustin and E. Delagnes for their contribution to the smooth running of the workshop. The symposium was free of fees and was made possible thanks to the financial support from DAPNIA-CEA and IN2P3-CNRS, the two major French research organizations that are gratefully acknowledged. Finally I want to thank the speakers for the high quality of their talks and all participants for coming to Paris and actively contributing in the meeting. The symposium was dedicated to the memory of Mike Ronan who left us a few months before. Mike was organizing in Berkeley a similar series of TPC workshops. David Nygren reviewed Mike Ronan's contribution to physics and especially to the development of new TPCs. Ioannis Giomataris Chair of the Organizing Committee International Advisory Committee Bouchez J. jacques.bouchez@cea.frNygren D-R. DRNygren@lbl.gov Charpak G. charpak@emse.frPaschos E. paschos@physik.uni-dortmund.de Collar J. collar@uchicago.eduShipsey I. shipsey@physics.purdue.edu Garwin R. RSA@watson.ibm.comSinclair D. D.sinclair@physics.carleton.ca Iliopoulos J. ilio@lpt.ens.frSpiro M. mspiro@admin.in2p3.fr Katsanevas S. katsan@admin.in2p3.frSpooner N. n.spooner@sheffield.ac.uk Mansoulié B. bruno.mansoulie@cea.frVergados J-D. vergados@cc.uoi.gr Morales J. jmorales@unizar.esVignaud D. vignaud@cdf.in2p3.fr Local Organizing Committee Busto J. busto@cppm.in2p3.frGiomataris I. ioa@hep.saclay.cea.fr (chairman) Colas P. paul.colas@cea.frGorodetzky Ph. philippe.gorodetzky@cern.ch Coudray Lydia (secretary)Irastorza I.G. Igor.Irastorza@cern.ch Fauvel Patricia (secretary)Vuilleumier J-L. jean-Luc.vuilleumier@unine.ch

  16. Does 3rd Age + 3rd World = 3rd Class?

    ERIC Educational Resources Information Center

    Tout, Ken

    1992-01-01

    Demographic changes, migration, and industrialization are having drastic effects on older adults in developing nations. Local programs such as Pro Vida in Colombia, supported by Help Age International, rely on the support of volunteers to improve the quality of life for elderly people. (SK)

  17. PREFACE: 3rd International Workshop on Statistical Physics and Mathematics for Complex Systems (SPMCS 2012)

    NASA Astrophysics Data System (ADS)

    Tayurskii, Dmitrii; Abe, Sumiyoshi; Alexandre Wang, Q.

    2012-11-01

    The 3rd International Workshop on Statistical Physics and Mathematics for Complex Systems (SPMCS2012) was held between 25-30 August at Kazan (Volga Region) Federal University, Kazan, Russian Federation. This workshop was jointly organized by Kazan Federal University and Institut Supérieur des Matériaux et Mécaniques Avancées (ISMANS), France. The series of SPMCS workshops was created in 2008 with the aim to be an interdisciplinary incubator for the worldwide exchange of innovative ideas and information about the latest results. The first workshop was held at ISMANS, Le Mans (France) in 2008, and the third at Huazhong Normal University, Wuhan (China) in 2010. At SPMCS2012, we wished to bring together a broad community of researchers from the different branches of the rapidly developing complexity science to discuss the fundamental theoretical challenges (geometry/topology, number theory, statistical physics, dynamical systems, etc) as well as experimental and applied aspects of many practical problems (condensed matter, disordered systems, financial markets, chemistry, biology, geoscience, etc). The program of SPMCS2012 was prepared based on three categories: (i) physical and mathematical studies (quantum mechanics, generalized nonequilibrium thermodynamics, nonlinear dynamics, condensed matter physics, nanoscience); (ii) natural complex systems (physical, geophysical, chemical and biological); (iii) social, economical, political agent systems and man-made complex systems. The conference attracted 64 participants from 10 countries. There were 10 invited lectures, 12 invited talks and 28 regular oral talks in the morning and afternoon sessions. The book of Abstracts is available from the conference website (http://www.ksu.ru/conf/spmcs2012/?id=3). A round table was also held, the topic of which was 'Recent and Anticipated Future Progress in Science of Complexity', discussing a variety of questions and opinions important for the understanding of the concept of

  18. Building monument materials during the 3rd-4rd millennium (Portugal)

    NASA Astrophysics Data System (ADS)

    Moita, Patricia; Pedro, Jorge; Boaventura, Rui; Mataloto, Rui; Maximo, Jaime; Almeida, Luís; Nogueira, Pedro

    2014-05-01

    Dolmens are the most conspicuous remains of the populations of the 4th and first half of 3rd millennia BCE. These tombs are impressive not only for their monumentality, but also because of the socioeconomic investment they represent for those Neolithic communities, namely from the Central-South of Portugal, who built them. Although dolmens have been studied for their funerary content and typologies, an interdisciplinary approach toward the geological characterization and sourcing of stones used in these constructions has not received enough attention from researchers. With MEGAGEO project a multidisciplinary group of geologist and archaeologists intends to assess the relationship between the distribution of dolmens in Central-South Portugal, their source materials, and the geological landscape. GIS will map the information gathered and will be used to analyse these relationships. The selection of the areas, with distinctive geologies (limestone vs granite), will allow to verify if human patterns of behaviour regarding the selection of megaliths are similar or different regionally. Geologically the first target area (Freixo, Alentejo) is dominated by a small intrusion of gabbro mingled/mixed within a granodioritic intrusion both related with variscan orogeny. Granodiorite exhibit several enclaves of igneous and metamorphic nature attesting the interaction between both igneous rocks as well with enclosing gneisses. Despite Alentejo region have a reduced number of outcrops the granodiorite provides rounded to tabular metric blocks. The gabbro is very coarse grained, sometimes with a cumulate texture, and their fracturing and weathering provide very fresh tabular blocks. The five studied dolmens (Quinta do Freixo #1 to #5) are implanted in a large granodioritic intrusion, around the gabbroic rocks, within an area of approximately 9km2. The medium grained granodiorite is ubiquity in all the dolmens slabs and occasionally it can be observed features of mixing and

  19. SESAME — A 3rd Generation Synchrotron Light Source for the Middle East

    NASA Astrophysics Data System (ADS)

    Å°lkü, Dinçer; Rahighi, Javad; Winick, Herman

    2007-01-01

    SESAME (Synchrotron-light for Experimental Science and Applications in the Middle East) will be the Middle East's first international research center. It is a cooperative venture by the scientists and governments of the region with founding members Bahrain, Egypt, Israel, Jordan, Pakistan, Palestine Authority, and Turkey. Iran is in the process of finalizing its formal membership. Other countries (Cyprus, Morocco, and the United Arab Emirates) are also expected to join. The permanent Council of member states has full responsibility for the project. Members provide the annual operating budget. Observer countries are Germany, Greece, Italy, Kuwait, Portugal, Russian Federation, Sweden, the UK, and the US. SESAME is being developed under the umbrella of UNESCO. Jordan was selected as the building site. SESAME will offer excellent opportunities for training of Middle East scientists and attract those working abroad to consider returning. SESAME will be a 2.5GeV 3rd Generation light source (emittance 26nm-rad, circumference ˜133m), providing excellent performance for structural molecular biology, molecular environmental science, surface and interface science, microelectromechanical devices, x-ray imaging, archaeological microanalysis, and materials characterization. It will cover a broad spectral range from the infrared to hard x-rays and will have 12 straight sections for insertion devices (average length 2.75m). The injector will be the BESSY I 0.8 GeV booster synchrotron which has been given as a gift from Germany. Four committees advise the Council and assist in developing the technical design, beam lines, user community, and scientific Program. The SESAME building, now in construction with funds and a site provided by Jordan, is scheduled for completion in late 2006 after which the BESSY I injector will be installed. First stored beam in the new 2.5 GeV ring is planned for 2009 with six initial beamlines planned. Some beamlines will be built by member countries

  20. SESAME - A 3rd Generation Synchrotron Light Source for the Middle East

    NASA Astrophysics Data System (ADS)

    U˝Lkü, Dinçer; Rahighi, Javad; Winick, Herman

    2007-01-01

    SESAME (Synchrotron-light for Experimental Science and Applications in the Middle East) will be the Middle East's first international research center. It is a cooperative venture by the scientists and governments of the region with founding members Bahrain, Egypt, Israel, Jordan, Pakistan, Palestine Authority, and Turkey. Iran is in the process of finalizing its formal membership. Other countries (Cyprus, Morocco, and the United Arab Emirates) are also expected to join. The permanent Council of member states has full responsibility for the project. Members provide the annual operating budget. Observer countries are Germany, Greece, Italy, Kuwait, Portugal, Russian Federation, Sweden, the UK, and the US. SESAME is being developed under the umbrella of UNESCO. Jordan was selected as the building site. SESAME will offer excellent opportunities for training of Middle East scientists and attract those working abroad to consider returning. SESAME will be a 2.5GeV 3rd Generation light source (emittance 26nm-rad, circumference ~133m), providing excellent performance for structural molecular biology, molecular environmental science, surface and interface science, microelectromechanical devices, x-ray imaging, archaeological microanalysis, and materials characterization. It will cover a broad spectral range from the infrared to hard x-rays and will have 12 straight sections for insertion devices (average length 2.75m). The injector will be the BESSY I 0.8 GeV booster synchrotron which has been given as a gift from Germany. Four committees advise the Council and assist in developing the technical design, beam lines, user community, and scientific Program. The SESAME building, now in construction with funds and a site provided by Jordan, is scheduled for completion in late 2006 after which the BESSY I injector will be installed. First stored beam in the new 2.5 GeV ring is planned for 2009 with six initial beamlines planned. Some beamlines will be built by member countries

  1. Essential surgery: key messages from Disease Control Priorities, 3rd edition.

    PubMed

    Mock, Charles N; Donkor, Peter; Gawande, Atul; Jamison, Dean T; Kruk, Margaret E; Debas, Haile T

    2015-05-30

    The World Bank will publish the nine volumes of Disease Control Priorities, 3rd edition, in 2015-16. Volume 1--Essential Surgery--identifies 44 surgical procedures as essential on the basis that they address substantial needs, are cost effective, and are feasible to implement. This report summarises and critically assesses the volume's five key findings. First, provision of essential surgical procedures would avert about 1·5 million deaths a year, or 6-7% of all avertable deaths in low-income and middle-income countries. Second, essential surgical procedures rank among the most cost effective of all health interventions. The surgical platform of the first-level hospital delivers 28 of the 44 essential procedures, making investment in this platform also highly cost effective. Third, measures to expand access to surgery, such as task sharing, have been shown to be safe and effective while countries make long-term investments in building surgical and anaesthesia workforces. Because emergency procedures constitute 23 of the 28 procedures provided at first-level hospitals, expansion of access requires that such facilities be widely geographically diffused. Fourth, substantial disparities remain in the safety of surgical care, driven by high perioperative mortality rates including anaesthesia-related deaths in low-income and middle-income countries. Feasible measures, such as WHO's Surgical Safety Checklist, have led to improvements in safety and quality. Fifth, the large burden of surgical disorders, cost-effectiveness of essential surgery, and strong public demand for surgical services suggest that universal coverage of essential surgery should be financed early on the path to universal health coverage. We point to estimates that full coverage of the component of universal coverage of essential surgery applicable to first-level hospitals would require just over US$3 billion annually of additional spending and yield a benefit-cost ratio of more than 10:1. It would

  2. ic-cmtp3: 3rd International Conference on Competitive Materials and Technology Processes

    NASA Astrophysics Data System (ADS)

    2016-04-01

    Competitiveness is one of the most important factors in our lives and it plays a key role in the efficiency both of organizations and societies. The more scientifically advanced and prepared organizations develop more competitive materials with better physical, chemical, and biological properties, and the leading companies apply more competitive equipment and technological processes. The aims of the 3rd International Conference on Competitive Materials and Technology Processes (ic-cmtp3), and the 1st International Symposium on Innovative Carbons and Carbon Based Materials (is-icbm1) and the 1st International Symposium on Innovative Construction Materials (is-icm1) organized alongside are the following: —Promote new methods and results of scientific research in the fields of material, biological, environmental and technological sciences; —Exchange information between the theoretical and applied sciences as well as technical and technological implementations; —Promote communication and collaboration between the scientists, researchers and engineers of different nations, countries and continents. Among the major fields of interest are advanced and innovative materials with competitive characteristics, including mechanical, physical, chemical, biological, medical and thermal, properties and extreme dynamic strength. Their crystalline, nano - and micro-structures, phase transformations as well as details of their technological processes, tests and measurements are also in the focus of the ic-cmtp3 conference and the is-scbm1 and is-icm1 symposia. Multidisciplinary applications of material science and the technological problems encountered in sectors like ceramics, glasses, thin films, aerospace, automotive and marine industries, electronics, energy, construction materials, medicine, biosciences and environmental sciences are of particular interest. In accordance with the program of the ic-cmtp3 conference and is-icbm1 and is-icm1 symposia we have received more

  3. SESAME - A 3rd Generation Synchrotron Light Source for the Middle East

    SciTech Connect

    Ulkue, Dincer; Rahighi, Javad; Winick, Herman

    2007-01-19

    SESAME (Synchrotron-light for Experimental Science and Applications in the Middle East) will be the Middle East's first international research center. It is a cooperative venture by the scientists and governments of the region with founding members Bahrain, Egypt, Israel, Jordan, Pakistan, Palestine Authority, and Turkey. Iran is in the process of finalizing its formal membership. Other countries (Cyprus, Morocco, and the United Arab Emirates) are also expected to join. The permanent Council of member states has full responsibility for the project. Members provide the annual operating budget. Observer countries are Germany, Greece, Italy, Kuwait, Portugal, Russian Federation, Sweden, the UK, and the US. SESAME is being developed under the umbrella of UNESCO. Jordan was selected as the building site. SESAME will offer excellent opportunities for training of Middle East scientists and attract those working abroad to consider returning. SESAME will be a 2.5GeV 3rd Generation light source (emittance 26nm-rad, circumference {approx}133m), providing excellent performance for structural molecular biology, molecular environmental science, surface and interface science, microelectromechanical devices, x-ray imaging, archaeological microanalysis, and materials characterization. It will cover a broad spectral range from the infrared to hard x-rays and will have 12 straight sections for insertion devices (average length 2.75m). The injector will be the BESSY I 0.8 GeV booster synchrotron which has been given as a gift from Germany. Four committees advise the Council and assist in developing the technical design, beam lines, user community, and scientific Program. The SESAME building, now in construction with funds and a site provided by Jordan, is scheduled for completion in late 2006 after which the BESSY I injector will be installed. First stored beam in the new 2.5 GeV ring is planned for 2009 with six initial beamlines planned. Some beamlines will be built by member

  4. PREFACE: 3rd International Workshop on "State of the Art in Nuclear Cluster Physics"

    NASA Astrophysics Data System (ADS)

    Yamada, Taiichi; Kanada-En'yo, Yoshiko

    2014-12-01

    The 3rd International Workshop on "State of the Art in Nuclear Cluster Physics"(SOTANCP3) was held at KGU Kannai Media Center, Kanto Gakuin University, Yokohama, Japan, from May 26 to 30, 2014. Yokohama is the second largest city in Japan, about 25 km southeast of Tokyo. The first workshop of the series was held in Strasbourg, France, in 2008 and the second one was in Brussels, Belgium, in 2010. The purpose of SOTANCP3 was to discuss the present status and future perspectives of the nuclear cluster physics. The following nine topics were selected in order to cover most of the scientific programme and highlight an area where new ideas have emerged over recent years: (1) Cluster structures and many-body correlations in stable and unstable nuclei (2) Clustering aspects of nuclear reactions and resonances (3) Alpha condensates and analogy with condensed matter approaches (4) Role of tensor force in cluster physics and ab initio approaches (5) Clustering in hypernuclei (6) Nuclear fission, superheavy nuclei, and cluster decay (7) Cluster physics and nuclear astrophysics (8) Clustering in nuclear matter and neutron stars (9) Clustering in hadron and atomic physics There were 122 participants, including 53 from 17 foreign countries. In addition to invited talks, we had many talks selected from contributed papers. There were plenary, parallel, and poster sessions. Poster contributions were also presented as four-minute talks in parallel sessions. This proceedings contains the papers presented in invited and selected talks together with those presented in poster sessions. We would like to express our gratitude to the members of the International Advisory Committee and those of the Organizing Committee for their efforts which made this workshop successful. In particular we would like to present our great thanks to Drs. Y. Funaki, W. Horiuchi, N. Itagaki, M. Kimura, T. Myo, and T. Yoshida. We would like also to thank the following organizations for their sponsors: RCNP

  5. A global drought climatology for the 3rd edition of the World Atlas of Desertification (WAD)

    NASA Astrophysics Data System (ADS)

    Spinoni, Jonathan; Carrao, Hugo; Naumann, Gustavo; Antofie, Tiberiu; Barbosa, Paulo; Vogt, Jürgen

    2013-04-01

    A new version of the World Atlas of Desertification (WAD) is being compiled in the framework of cooperation between the Joint Research Centre (JRC) of the European Commission and the United Nations Environment Programme (UNEP). This initiative aims at mapping the global land degradation and desertification, as well as introducing the reader with complex interactions of geo-physical, socio-economic, and political aspects that affect the environmental sustainability. Recurrent extreme events resulting from climate change, such as more severe droughts, combined with non-adapted land use practices can affect the resilience of ecosystems tipping them into a less productive state. Thus, to describe the effects of climatological hazards on land degradation and desertification processes, we computed a World drought climatology that will be part of the 3rd edition of the WAD and will replace and update to 2010 the results presented in the 2nd edition in 1997. This paper presents the methodology used to compute three parameters included in the WAD drought climatology, i.e. drought frequency, intensity and duration, and discusses their spatio-temporal patterns both at global and continental scales. Because drought is mainly driven and triggered by a rainfall deficit, we chose the Standardized Precipitation Index (SPI) as the drought indicator to estimate our climatological parameters. The SPI is a statistical precipitation-based drought indicator widely used in drought-related studies. We calculated the SPI on three different accumulation periods: 3 months (SPI-3), 6 months (SPI-6), and 12 months (SPI-12), in order to take into account meteorological, agricultural, and hydrological drought-related features. Each quantity has been calculated on a monthly basis using the baseline period between January 1951 and December 2010. As data input, we used the Full Data Reanalysis Version 6.0 (0.5˚x0.5˚) of gridded monthly precipitation provided by the Global Precipitation

  6. PREFACE: 3rd International Workshop on Materials Analysis and Processing in Magnetic Fields (MAP3)

    NASA Astrophysics Data System (ADS)

    Sakka, Yoshio; Hirota, Noriyuki; Horii, Shigeru; Ando, Tsutomu

    2009-07-01

    The 3rd International Workshop on Materials Analysis and Processing in Materials Fields (MAP3) was held on 14-16 May 2008 at the University of Tokyo, Japan. The first was held in March 2004 at the National High Magnetic Field Laboratory in Tallahassee, USA. Two years later the second took place in Grenoble, France. MAP3 was held at The University of Tokyo International Symposium, and jointly with MANA Workshop on Materials Processing by External Stimulation, and JSPS CORE Program of Construction of the World Center on Electromagnetic Processing of Materials. At the end of MAP3 it was decided that the next MAP4 will be held in Atlanta, USA in 2010. Processing in magnetic fields is a rapidly expanding research area with a wide range of promising applications in materials science. MAP3 focused on the magnetic field interactions involved in the study and processing of materials in all disciplines ranging from physics to chemistry and biology: Magnetic field effects on chemical, physical, and biological phenomena Magnetic field effects on electrochemical phenomena Magnetic field effects on thermodynamic phenomena Magnetic field effects on hydrodynamic phenomena Magnetic field effects on crystal growth Magnetic processing of materials Diamagnetic levitation Magneto-Archimedes effect Spin chemistry Application of magnetic fields to analytical chemistry Magnetic orientation Control of structure by magnetic fields Magnetic separation and purification Magnetic field-induced phase transitions Materials properties in high magnetic fields Development of NMR and MRI Medical application of magnetic fields Novel magnetic phenomena Physical property measurement by Magnetic fields High magnetic field generation> MAP3 consisted of 84 presentations including 16 invited talks. This volume of Journal of Physics: Conference Series contains the proceeding of MAP3 with 34 papers that provide a scientific record of the topics covered by the conference with the special topics (13 papers) in

  7. PREFACE: 3rd Workshop on Theory, Modelling and Computational Methods for Semiconductors (TMCSIII)

    NASA Astrophysics Data System (ADS)

    Califano, Marco; Migliorato, Max; Probert, Matt

    2012-05-01

    These conference proceedings contain the written papers of the contributions presented at the 3rd International Conference on Theory, Modelling and Computational Methods for Semiconductor materials and nanostructures. The conference was held at the School of Electronic and Electrical Engineering, University of Leeds, Leeds, UK on 18-20 January 2012. The previous conferences in this series took place in 2010 at St William's College, York and in 2008 at the University of Manchester, UK. The development of high-speed computer architectures is finally allowing the routine use of accurate methods for calculating the structural, thermodynamic, vibrational, optical and electronic properties of semiconductors and their hetero- and nano-structures. The scope of this conference embraces modelling, theory and the use of sophisticated computational tools in semiconductor science and technology, where there is substantial potential for time-saving in R&D. Theoretical approaches represented in this meeting included: Density Functional Theory, Tight Binding, Semiempirical Pseudopotential Methods, Effective Mass Models, Empirical Potential Methods and Multiscale Approaches. Topics included, but were not limited to: Optical and Transport Properties of Quantum Nanostructures including Colloids and Nanotubes, Plasmonics, Magnetic Semiconductors, Graphene, Lasers, Photonic Structures, Photovoltaic and Electronic Devices. This workshop ran for three days, with the objective of bringing together UK and international leading experts in the theoretical modelling of Group IV, III-V and II-VI semiconductors, as well as students, postdocs and early-career researchers. The first day focused on providing an introduction and overview of this vast field, aimed particularly at students, with several lectures given by recognised experts in various theoretical approaches. The following two days showcased some of the best theoretical research carried out in the UK in this field, with several

  8. FOREWORD: 3rd International Workshop on New Computational Methods for Inverse Problems (NCMIP 2013)

    NASA Astrophysics Data System (ADS)

    Blanc-Féraud, Laure; Joubert, Pierre-Yves

    2013-10-01

    Conference logo This volume of Journal of Physics: Conference Series is dedicated to the scientific contributions presented during the 3rd International Workshop on New Computational Methods for Inverse Problems, NCMIP 2013 (http://www.farman.ens-cachan.fr/NCMIP_2013.html). This workshop took place at Ecole Normale Supérieure de Cachan, in Cachan, France, on 22 May 2013, at the initiative of Institut Farman. The prior editions of NCMIP also took place in Cachan, France, firstly within the scope of the ValueTools Conference, in May 2011 (http://www.ncmip.org/2011/), and secondly at the initiative of Institut Farman, in May 2012 (http://www.farman.ens-cachan.fr/NCMIP_2012.html). The NCMIP Workshop focused on recent advances in the resolution of inverse problems. Indeed inverse problems appear in numerous scientific areas such as geophysics, biological and medical imaging, material and structure characterization, electrical, mechanical and civil engineering, and finances. The resolution of inverse problems consists of estimating the parameters of the observed system or structure from data collected by an instrumental sensing or imaging device. Its success firstly requires the collection of relevant observation data. It also requires accurate models describing the physical interactions between the instrumental device and the observed system, as well as the intrinsic properties of the solution itself. Finally, it requires the design of robust, accurate and efficient inversion algorithms. Advanced sensor arrays and imaging devices provide high rate and high volume data; in this context, the efficient resolution of the inverse problem requires the joint development of new models and inversion methods, taking computational and implementation aspects into account. During this one-day workshop, researchers had the opportunity to bring to light and share new techniques and results in the field of inverse problems. The topics of the workshop were: algorithms and computational

  9. Mechanical design and engineering of the 3.9 GHZ, 3rd harmonic SRF system at Fermilab

    SciTech Connect

    Don Mitchell et al.

    2004-08-05

    The mechanical development of the 3.9 GHz, 3rd Harmonic SRF System is summarized to include: the development of a full scale copper prototype cavity structure; the design of the niobium 3 cell and niobium 9 cell structures; the design of the helium vessel and cryostat; the HOM coupler design; and a preliminary look at the main coupler design. The manufacturing processes for forming, rolling, and e-beam welding the HOM coupler, cavity cells, and end tubes are also described. Due to the exotic materials and manufacturing processes used in this type of device, a cost estimate for the material and fabrication is provided. The 3rd harmonic design is organized via a web-based data management approach.

  10. The effect of surgical technique on lingual nerve damage during lower 3rd molar removal by dental students.

    PubMed

    Robinson, P P; Loescher, A R; Smith, K G

    1999-05-01

    We have previously shown that avoidance of lingual flap retraction with a Howarth periosteal elevator during lower 3rd molar removal, reduces the incidence of lingual nerve damage. In that study, the surgery was undertaken by qualified staff and we have now assessed the effect of revising the method taught to our junior undergraduate dental students. We evaluated the outcome of surgery undertaken by 2 consecutive years of students, each group being taught 1 of the 2 methods. A total of 200 patients requiring lower 3rd molar removal under local anaesthesia were included in the study. In year 1, the surgery included elevation of a lingual flap and insertion of a Howarth elevator adjacent to the lingual plate; in year 2 this part of the procedure was avoided by using a purely buccal approach. There were no significant differences between the levels of tooth eruption and types of impaction of the teeth removed in each year. Lingual sensory disturbance occurred in 3 patients in the 'flap' group (3.3%) and in 1 patient (0.9%) in the 'no flap' group. As this incidence is not significantly different in the 2 groups (P < 0.4), we conclude that avoidance of lingual retraction by students undertaking lower 3rd molar removal does not appear to place the lingual nerve at greater risk. In view of the results of our previous study, we therefore advocate this method for use in undergraduate dental education. PMID:10530161

  11. Macroscale and Microscale Organic Experiments, 3rd Edition (by Kenneth L. Williamson)

    NASA Astrophysics Data System (ADS)

    Keeffe, Reviewed By James

    1999-11-01

    suggested semiempirical computations. Other new texts, for example that by Pavia et al. (3rd ed., 1999), take computation even further. New features in the third edition include reduction of the macroscale experimental quantities to amounts compatible with 14/20 standard-taper glassware. Additionally, there are some useful and characteristically clever equipment adaptations for microfiltration and gas phase IR spectra, a few new or updated experiments, replacement of all IR spectra by Fourier transform spectra, and routine use of 250-MHz 1H NMR spectra. Two-dimensional NMR spectroscopy is briefly discussed but not further encountered. One new feature which looks promising is called "Surfing the Web". Pertinent Web site addresses dot the book, but it would be useful if these were indexed as a group. The brief but up-to-date chapter on searching the literature includes addresses and some advice on accessing commercial databases. Regarding the lab course itself, two useful addresses are http://ull.chemistry.uakron.edu/organic_lab/ and Williamson's own site (under construction as I write), http://www.mtholyoke.edu/courses/kwilliam/microscale.shtml, where pictures of techniques and other support information will interest teachers and students alike. Williamson has always been responsive to users of his texts, and will probably be quick to incorporate new information and improved techniques at this site. There are a few areas where improvement can still be made. The chapter on IR spectroscopy, although revised, does not contain an extensive, conventional table of characteristic group frequencies. All our instructors supplement the text with standard tables. We also find the section on organic qualitative analysis to be limited and mildly difficult to use. Students must do a lot of page turning, back and forth, to find some of the tests and recipes needed. At SFSU more than half of our second-semester lab is given over to organic qual, and no single lab text except that of Pasto

  12. FOREWORD: 3rd International Workshop on New Computational Methods for Inverse Problems (NCMIP 2013)

    NASA Astrophysics Data System (ADS)

    Blanc-Féraud, Laure; Joubert, Pierre-Yves

    2013-10-01

    Conference logo This volume of Journal of Physics: Conference Series is dedicated to the scientific contributions presented during the 3rd International Workshop on New Computational Methods for Inverse Problems, NCMIP 2013 (http://www.farman.ens-cachan.fr/NCMIP_2013.html). This workshop took place at Ecole Normale Supérieure de Cachan, in Cachan, France, on 22 May 2013, at the initiative of Institut Farman. The prior editions of NCMIP also took place in Cachan, France, firstly within the scope of the ValueTools Conference, in May 2011 (http://www.ncmip.org/2011/), and secondly at the initiative of Institut Farman, in May 2012 (http://www.farman.ens-cachan.fr/NCMIP_2012.html). The NCMIP Workshop focused on recent advances in the resolution of inverse problems. Indeed inverse problems appear in numerous scientific areas such as geophysics, biological and medical imaging, material and structure characterization, electrical, mechanical and civil engineering, and finances. The resolution of inverse problems consists of estimating the parameters of the observed system or structure from data collected by an instrumental sensing or imaging device. Its success firstly requires the collection of relevant observation data. It also requires accurate models describing the physical interactions between the instrumental device and the observed system, as well as the intrinsic properties of the solution itself. Finally, it requires the design of robust, accurate and efficient inversion algorithms. Advanced sensor arrays and imaging devices provide high rate and high volume data; in this context, the efficient resolution of the inverse problem requires the joint development of new models and inversion methods, taking computational and implementation aspects into account. During this one-day workshop, researchers had the opportunity to bring to light and share new techniques and results in the field of inverse problems. The topics of the workshop were: algorithms and computational

  13. Characterization of an Acinetobacter baumannii lptD Deletion Strain: Permeability Defects and Response to Inhibition of Lipopolysaccharide and Fatty Acid Biosynthesis

    PubMed Central

    Bojkovic, Jade; Richie, Daryl L.; Six, David A.; Rath, Christopher M.; Sawyer, William S.; Hu, Qijun

    2015-01-01

    ABSTRACT Lipid A on the Gram-negative outer membrane (OM) is synthesized in the cytoplasm by the Lpx pathway and translocated to the OM by the Lpt pathway. Some Acinetobacter baumannii strains can tolerate the complete loss of lipopolysaccharide (LPS) resulting from the inactivation of early LPS pathway genes such as lpxC. Here, we characterized a mutant deleted for lptD, which encodes an OM protein that mediates the final translocation of fully synthesized LPS to the OM. Cells lacking lptD had a growth defect comparable to that of an lpxC deletion mutant under the growth conditions tested but were more sensitive to hydrophobic antibiotics, revealing a more significant impact on cell permeability from impaired LPS translocation than from the loss of LPS synthesis. Consistent with this, ATP leakage and N-phenyl-1-naphthylamine (NPN) fluorescence assays indicated a more severe impact of lptD deletion than of lpxC deletion on inner and outer membrane permeability, respectively. Targeted liquid chromatography-mass spectrometry (LCMS) analysis of LPS intermediates from UDP-3-O-R-3-hydroxylauroyl-N-acetyl-α-d-glucosamine through lipid IVA showed that the loss of LptD caused an accumulation of lipid IVA. This suggested that pathway intermediate accumulation or mislocalization caused by the blockage of later LPS pathway steps impacts envelope integrity. Supporting this notion, chemical inhibition of lipid A precursor enzymes, including LpxC and FabB/F, in the lptD deletion strain partially rescued growth and permeability defects. IMPORTANCE New antibiotics to treat Gram-negative bacterial infections are urgently needed. Inhibition of LPS biosynthesis is attractive because this would impact viability and cell permeability. Therefore, a better understanding of this pathway is important, especially in strains such as A. baumannii ATCC 19606, where LPS biosynthesis is not essential in vitro. We show that ATCC 19606 also survives the loss of the final translocation of LPS into

  14. Influence of solar eclipse of November 3rd, 2013 on the total ozone column over Badajoz, Spain

    NASA Astrophysics Data System (ADS)

    Mateos, D.; Antón, M.; Vaquero, J. M.

    2014-05-01

    The hybrid eclipse of November 3rd, 2013 was observed as partial with a magnitude equal to 0.126 from Badajoz (38° 53‧ N, 6° 58‧ W). The evolution of the total ozone column (TOC) values for 4 h was monitored using a Solar Light Microtops-II manual sun-photometer. Before the eclipse, TOC remained invariable ~280 Dobson Units (DU) for one hour and a half. Once the eclipse was started, a clear decrease in TOC occurred. After the eclipse maximum (with TOC=273 DU), a rapid TOC recovery was observed. When the eclipse was over, TOC came back to values ~280 DU.

  15. Quantitative metabolic profiles of 2nd and 3rd trimester human amniotic fluid using 1H HR-MAS spectroscopy

    PubMed Central

    Cohn, Brad R.; Zhao, Shoujun; Kornak, John; Zhang, Vickie Y.; Iman, Rahwa; Kurhanewicz, John; Vahidi, Kiarash; Yu, Jingwei; Caughey, Aaron B.; Swanson, Mark G.

    2016-01-01

    Object To establish and compare normative metabolite concentrations in 2nd and 3rd trimester human amniotic fluid samples in an effort to reveal metabolic biomarkers of fetal health and development. Materials and methods Twenty-one metabolite concentrations were compared between 2nd (15–27 weeks gestation, N = 23) and 3rd (29–39 weeks gestation, N = 27) trimester amniotic fluid samples using 1H high resolution magic angle spinning (HR-MAS) spectroscopy. Data were acquired using the electronic reference to access in vivo concentrations method and quantified using a modified semi-parametric quantum estimation algorithm modified for high-resolution ex vivo data. Results Sixteen of 21 metabolite concentrations differed significantly between 2nd and 3rd trimester groups. Betaine (0.00846±0.00206 mmol/kg vs. 0.0133±0.0058 mmol/kg, P <0.002) and creatinine (0.0124±0.0058 mmol/kg vs. 0.247±0.011 mmol/kg, P <0.001) concentrations increased significantly, while glucose (5.96±1.66 mmol/kg vs. 2.41±1.69 mmol/kg, P <0.001), citrate (0.740±0.217 mmol/kg vs. 0.399±0.137 mmol/kg, P <0.001), pyruvate (0.0659±0.0103 mmol/kg vs. 0.0299±0.286 mmol/kg, P <0.001), and numerous amino acid (e.g. alanine, glutamate, isoleucine, leucine, lysine, and valine) concentrations decreased significantly with advancing gestation. A stepwise multiple linear regression model applied to 50 samples showed that gestational age can be accurately predicted using combinations of alanine, glucose and creatinine concentrations. Conclusion These results provide key normative data for 2nd and 3rd trimester amniotic fluid metabolite concentrations and provide the foundation for future development of magnetic resonance spectroscopy (MRS) biomarkers to evaluate fetal health and development. PMID:19779747

  16. PREFACE: 3rd Iberian Meeting on Aerosol Science and Technology (RICTA 2015)

    NASA Astrophysics Data System (ADS)

    Orza, J. A. G.; Costa, M. J.

    2015-12-01

    The Third Iberian Meeting on Aerosol Science and Technology (RICTA 2015) was held in the city of Elche (province of Alicante, Spain) from 29 June to 1 July 2015, at Centro de Congresos Ciutat d'Elx. This event was organized and hosted by the Statistical and Computational Physics Laboratory (SCOLAb) of Universidad Miguel Hernández under the auspices of AECyTA, the Spanish Association for Aerosol Science and Technology Research. As in previous editions, the participation of young researchers was especially welcome, with the organization of the VI Summer School on Aerosol Science and Technology and awards for the best poster and PhD thesis, in recognition of outstanding research or presentations focusing on aerosols, during the early stage of their scientific career. RICTA 2015 aims to present the latest research and advances on the field of aerosols, as well as fostering interaction among the Portuguese and Spanish communities. The meeting gathered over 70 participants from 7 different countries, covering a wide range of aerosol science and technology. It included invited lectures, keynote talks, and several specialized sessions on different issues related to atmospheric aerosols, radiation, instrumentation, fundamental aerosol science, bioaerosols and health effects. The editors would like to express their sincere gratitude to all the participants, in particular, those who contributed to this special issue by submitting their papers to convey the current science discussed at RICTA 2015. In this special issue a series of peer-reviewed papers that cover a wide range of topics are presented: aerosol formation, emission, as well as aerosol composition in terms of physical and optical properties, spatial/temporal distribution of aerosol parameters, aerosol modeling and atmospheric effects, as well as instrumentation devoted to aerosol measurements. Finally, we also thank the referees for their valuable revision of these papers.

  17. Analysis and design of a 3rd order velocity-controlled closed-loop for MEMS vibratory gyroscopes.

    PubMed

    Wu, Huan-ming; Yang, Hai-gang; Yin, Tao; Jiao, Ji-wei

    2013-01-01

    The time-average method currently available is limited to analyzing the specific performance of the automatic gain control-proportional and integral (AGC-PI) based velocity-controlled closed-loop in a micro-electro-mechanical systems (MEMS) vibratory gyroscope, since it is hard to solve nonlinear functions in the time domain when the control loop reaches to 3rd order. In this paper, we propose a linearization design approach to overcome this limitation by establishing a 3rd order linear model of the control loop and transferring the analysis to the frequency domain. Order reduction is applied on the built linear model's transfer function by constructing a zero-pole doublet, and therefore mathematical expression of each control loop's performance specification is obtained. Then an optimization methodology is summarized, which reveals that a robust, stable and swift control loop can be achieved by carefully selecting the system parameters following a priority order. Closed-loop drive circuits are designed and implemented using 0.35 μm complementary metal oxide semiconductor (CMOS) process, and experiments carried out on a gyroscope prototype verify the optimization methodology that an optimized stability of the control loop can be achieved by constructing the zero-pole doublet, and disturbance rejection capability (D.R.C) of the control loop can be improved by increasing the integral term. PMID:24051522

  18. Poly(2-oxazoline) based micelles with high capacity for 3rd generation taxoids: preparation, in vitro and in vivo evaluation.

    PubMed

    He, Zhijian; Schulz, Anita; Wan, Xiaomeng; Seitz, Joshua; Bludau, Herdis; Alakhova, Daria Y; Darr, David B; Perou, Charles M; Jordan, Rainer; Ojima, Iwao; Kabanov, Alexander V; Luxenhofer, Robert

    2015-06-28

    The clinically and commercially successful taxanes, paclitaxel and docetaxel suffer from two major drawbacks, namely their very low aqueous solubility and the risk of developing resistance. Here, we present a method that overcomes both drawbacks in a very simple manner. We formulated 3rd generation taxoids, able to avoid common drug resistance mechanisms with doubly amphiphilic poly(2-oxazoline)s (POx), a safe and highly efficient polymer for the formulation of extremely hydrophobic drugs. We found excellent solubilization of different 3rd generation taxoids irrespective of the drug's chemical structures with essentially quantitative drug loading and final drug to polymer ratios around unity. The small, highly loaded micelles with a hydrodynamic diameter of less than 100nm are excellently suited for parenteral administration. Moreover, a selected formulation with the taxoid SB-T-1214 is about one to two orders of magnitude more active in vitro than paclitaxel in the multidrug resistant breast cancer cell line LCC6-MDR. In contrast, in wild-type LCC6, no difference was observed. Using a q4d×4 dosing regimen, we also found that POx/SB-T-1214 significantly inhibits the growth of LCC6-MDR orthotropic tumors, outperforming commercial paclitaxel drug Taxol and Cremophor EL formulated SB-T-1214. PMID:25725361

  19. Analysis and Design of a 3rd Order Velocity-Controlled Closed-Loop for MEMS Vibratory Gyroscopes

    PubMed Central

    Wu, Huan-ming; Yang, Hai-gang; Yin, Tao; Jiao, Ji-wei

    2013-01-01

    The time-average method currently available is limited to analyzing the specific performance of the automatic gain control-proportional and integral (AGC-PI) based velocity-controlled closed-loop in a micro-electro-mechanical systems (MEMS) vibratory gyroscope, since it is hard to solve nonlinear functions in the time domain when the control loop reaches to 3rd order. In this paper, we propose a linearization design approach to overcome this limitation by establishing a 3rd order linear model of the control loop and transferring the analysis to the frequency domain. Order reduction is applied on the built linear model's transfer function by constructing a zero-pole doublet, and therefore mathematical expression of each control loop's performance specification is obtained. Then an optimization methodology is summarized, which reveals that a robust, stable and swift control loop can be achieved by carefully selecting the system parameters following a priority order. Closed-loop drive circuits are designed and implemented using 0.35 μm complementary metal oxide semiconductor (CMOS) process, and experiments carried out on a gyroscope prototype verify the optimization methodology that an optimized stability of the control loop can be achieved by constructing the zero-pole doublet, and disturbance rejection capability (D.R.C) of the control loop can be improved by increasing the integral term. PMID:24051522

  20. Phosphoethanolamine Transferase LptA in Haemophilus ducreyi Modifies Lipid A and Contributes to Human Defensin Resistance In Vitro

    PubMed Central

    Trombley, Michael P.; Post, Deborah M. B.; Rinker, Sherri D.; Reinders, Lorri M.; Fortney, Kate R.; Zwickl, Beth W.; Janowicz, Diane M.; Baye, Fitsum M.; Katz, Barry P.; Spinola, Stanley M.; Bauer, Margaret E.

    2015-01-01

    Haemophilus ducreyi resists the cytotoxic effects of human antimicrobial peptides (APs), including α-defensins, β-defensins, and the cathelicidin LL-37. Resistance to LL-37, mediated by the sensitive to antimicrobial peptide (Sap) transporter, is required for H. ducreyi virulence in humans. Cationic APs are attracted to the negatively charged bacterial cell surface. In other gram-negative bacteria, modification of lipopolysaccharide or lipooligosaccharide (LOS) by the addition of positively charged moieties, such as phosphoethanolamine (PEA), confers AP resistance by means of electrostatic repulsion. H. ducreyi LOS has PEA modifications at two sites, and we identified three genes (lptA, ptdA, and ptdB) in H. ducreyi with homology to a family of bacterial PEA transferases. We generated non-polar, unmarked mutants with deletions in one, two, or all three putative PEA transferase genes. The triple mutant was significantly more susceptible to both α- and β-defensins; complementation of all three genes restored parental levels of AP resistance. Deletion of all three PEA transferase genes also resulted in a significant increase in the negativity of the mutant cell surface. Mass spectrometric analysis revealed that LptA was required for PEA modification of lipid A; PtdA and PtdB did not affect PEA modification of LOS. In human inoculation experiments, the triple mutant was as virulent as its parent strain. While this is the first identified mechanism of resistance to α-defensins in H. ducreyi, our in vivo data suggest that resistance to cathelicidin LL-37 may be more important than defensin resistance to H. ducreyi pathogenesis. PMID:25902140

  1. PREFACE: The 3rd ISESCO International Workshop and Conference On Nanotechnology 2012 (IWCN2012)

    NASA Astrophysics Data System (ADS)

    Umar, Akrajas Ali; Yahaya, Muhammad; Mat Salleh, Muhamad

    2013-04-01

    unwavering support dedicated by all the referees. Their tireless work has helped guarantee the high scientific level of this series. Many thanks are also addressed to the ISESCO, COMSATS, MASS, UKM and FST for their financial support. Logistics support provided by IMEN and MNA is also much appreciated. We realized that this volume would never have materialized without the hard work of Ms Siti Khatijah Md Saad who helped the editorial secretariat in many ways communicating with the authors and reviewers and checking and typesetting the papers in the final stage. Finally, great appreciation is addressed to all who have worked hard and given support ensuring that the conference was a success. Editors Associate Professor Dr Akrajas Ali Umar Professor Dr Muhamad Mat Salleh Professor Dato' Dr Muhammad Yahaya IWCN 2012 Organizing Committee International Advisory Board Professor Dato' Dr Muhammad Yahaya (UKM, Malaysia) Dr Faiq Bilal (ISESCO, Morocco) Professor Dr Michael Graetzel (Switzerland) Professor Dr Muhamad Rasat (Malaysia) Prof Dr Masbah R T Siregar (Indonesia) Associate Professor Dr Munetaka Oyama (Japan) Professor Dr Ismat Shah (USA) Professor Dr Muhamad Mat Salleh (Malaysia) Chairman Associate Professor Dr Mohammad Kassim Co-Chairman Dr Mohammad Hafizuddin Haji Jumali Secretary Dr Lorna Jeffry Minggu Treasurer Dr Sharina Abu Hanifah Committee Members Associate Professor Dr Mohd Azmi Abd Hamid Associate Professor Dr Akrajas Ali Umar Dr Zahari Ibarahim Dr Rozidawati Awang Dr Farah Hannan Anuar Secretariat Dr Khuzaimah Mohd Firdauz Ismail Izura Izzuddin Nor Huwaida Janil Jamil Siti Khatijah Md Saad Noor Razinah Rahmat Mark Lee Wun Fui Ng Kim Hang Lee Thian Khoon Law Kung Pui Choong Yan Yi

  2. Evaluation of VIDAS UP Listeria assay (LPT) for the detection of Listeria in a variety of foods and environmental surfaces: First Action 2013.10.

    PubMed

    Crowley, Erin; Bird, Patrick; Flannery, Jonathan; Benzinger, M Joseph; Fisher, Kiel; Boyle, Megan; Huffman, Travis; Bastin, Ben; Bedinghaus, Paige; Judd, William; Hoang, Thao; Agin, James; Goins, David; Johnson, Ronald L

    2014-01-01

    The VIDAS UP Listeria (LPT) is an automated rapid screening enzyme phage-ligand based assay for the detection of Listeria species in human food products and environmental samples. The VIDAS LPT method was compared in a multi-laboratory collaborative study to AOAC Official Method 993.12 Listeria monocytogenes in Milk and Dairy Products reference method following current AOAC guidelines. A total of 14 laboratories participated, representing government and industry, throughout the United States. One matrix, queso fresco (soft Mexican cheese), was analyzed using two different test portion sizes, 25 and 125 g. Samples representing each test portion size were artificially contaminated with Listeria species at three levels, an uninoculated control level [0 colony-forming units (CFU)/test portion], a low-inoculum level (0.2-2 CFU/test portion), and a high-inoculum level (2-5 CFU/test portion). For this evaluation, 1800 unpaired replicate test portions were analyzed by either the VIDAS LPT or AOAC 993.12. Each inoculation level was analyzed using the Probability of Detection (POD) statistical model. For the low-level inoculated test portions, difference in collaborator POD (dLPOD) values of 0.01, (-0.10, 0.13), with 95% confidence intervals, were obtained for both 25 and 125 g test portions. The range of the confidence intervals for dLPOD values for both the 25 and 125 g test portions contains the point 0.0 indicating no statistically significant difference in the number of positive samples detected between the VIDAS LPT and the AOAC methods. In addition to Oxford agar, VIDAS LPT test portions were confirmed using Agar Listeria Ottavani and Agosti (ALOA), a proprietary chromogenic agar for the identification and differentiation of L. monocytogenes and Listeria species. No differences were observed between the two selective agars. The VIDAS LPT method, with the optional ALOA agar confirmation method, was adopted as Official First Action status for the detection of Listeria

  3. Use of 2nd and 3rd Level Correlation Analysis for Studying Degradation in Polycrystalline Thin-Film Solar Cells

    SciTech Connect

    Albin, D. S.; del Cueto, J. A.; Demtsu, S. H.; Bansal, S.

    2011-03-01

    The correlation of stress-induced changes in the performance of laboratory-made CdTe solar cells with various 2nd and 3rd level metrics is discussed. The overall behavior of aggregated data showing how cell efficiency changes as a function of open-circuit voltage (Voc), short-circuit current density (Jsc), and fill factor (FF) is explained using a two-diode, PSpice model in which degradation is simulated by systematically changing model parameters. FF shows the highest correlation with performance during stress, and is subsequently shown to be most affected by shunt resistance, recombination and in some cases voltage-dependent collection. Large decreases in Jsc as well as increasing rates of Voc degradation are related to voltage-dependent collection effects and catastrophic shunting respectively. Large decreases in Voc in the absence of catastrophic shunting are attributed to increased recombination. The relevance of capacitance-derived data correlated with both Voc and FF is discussed.

  4. THE 3rd SCHIZOPHRENIA INTERNATIONAL RESEARCH SOCIETY CONFERENCE, 14-18 APRIL 2012, FLORENCE, ITALY: SUMMARIES OF ORAL SESSIONS

    PubMed Central

    Abbs, Brandon; Achalia, Rashmin M; Adelufosi, Adegoke O; Aktener, Ahmet Yiğit; Beveridge, Natalie J; Bhakta, Savita G; Blackman, Rachael K; Bora, Emre; Byun, MS; Cabanis, Maurice; Carrion, Ricardo; Castellani, Christina A; Chow, Tze Jen; Dmitrzak-Weglarz, M; Gayer-Anderson, Charlotte; Gomes, Felipe V; Haut, Kristen; Hori, Hiroaki; Kantrowitz, Joshua T; Kishimoto, Taishiro; Lee, Frankie HF; Lin, Ashleigh; Palaniyappan, Lena; Quan, Meina; Rubio, Maria D; Ruiz de Azúa, Sonia; Sahoo, Saddichha; Strauss, Gregory P; Szczepankiewicz, Aleksandra; Thompson, Andrew D; Trotta, Antonella; Tully, Laura M; Uchida, Hiroyuki; Velthorst, Eva; Young, Jared W; O’Shea, Anne; DeLisi, Lynn E.

    2013-01-01

    The 3rd Schizophrenia International Research Society Conference was held in Florence, Italy, April 14-18, 2012.and this year had as its emphasis, “The Globalization of Research”. Student travel awardees served as rapporteurs for each oral session and focused their summaries on the most significant findings that emerged and the discussions that followed. The following report is a composite of these summaries. We hope that it will provide an overview for those who were present, but could not participate in all sessions, and those who did not have the opportunity to attend, but who would be interested in an update on current investigations ongoing in the field of schizophrenia research. PMID:22910407

  5. An Investigation of the Relationship Between Retention in First Grade and Performance on High Stakes Tests in 3rd Grade

    PubMed Central

    Hughes, Jan N.; Chen, Qi; Thoemmes, Felix; Kwok, Oi-man

    2010-01-01

    The association between grade retention in first grade and passing the third grade state accountability tests, the Texas Assessment of Knowledge and Skills (TAKS) reading and math, was investigated in a sample of 769 students who were recruited into the study when they were in first grade. Of these 769 students, 165 were retained in first grade and 604 were promoted. Using propensity matching, we created five imputed datasets (average N=321) in which promoted and retained students were matched on 67 comprehensive covariates. Using GEE models, we obtained the association between retention and passing the 3rd grade TAKS reading and math tests. The positive association between retention and math scores was significant while the association was marginally significant for reading scores. PMID:20628547

  6. 76 FR 16526 - Airworthiness Directives; Pratt & Whitney JT8D-209, -217, -217A, -217C, and -219 Series Turbofan...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-24

    ... perform the 3rd and 4th stage LPT blade inspection, and 1.5 work-hours per engine to replace the LPT-to.... Less than 5 LB-IN (0.565 N.m)........ One or more Remove engine from service within 20 hours TIS since... than 10 LB-IN (1.130 N.m) but Seven or more Remove engine from service greater than or equal to 5...

  7. Early Acute Antibody-Mediated Rejection of a Negative Flow Crossmatch 3rd Kidney Transplant with Exclusive Disparity at HLA-DP

    PubMed Central

    Mierzejewska, Beata; Schroder, Paul M.; Baum, Caitlin E.; Blair, Annette; Smith, Connie; Duquesnoy, Rene J.; Marrari, Marilyn; Gohara, Amira; Malhotra, Deepak; Kaw, Dinkar; Liwski, Robert; Rees, Michael A.; Stepkowski, Stanislaw

    2014-01-01

    Donor-specific alloantibodies (DSA) to HLA-DP may cause antibody-mediated rejection (AMR), especially in re-transplants. We describe the immunization history of a patient who received 3 kidney transplants; the 3rd kidney was completely matched except at DPA1 and DPB1. Prior to the 3rd transplant, single antigen bead analysis (SAB) showed DSA reactivity against DPA1 shared by the 1st and 3rd donors, but B and T flow crossmatch (FXM) results were negative. Within 11 days the 3rd transplant underwent acute C4d+ AMR which coincided with the presence of complement (C1q)-binding IgG1 DSA against donor DPA1 and DPB1. Using HLAMatchmaker and SAB, we provide evidence that eplet (epitope) spreading on DPA1 and eplet sharing on differing DPB1 alleles of the 1st and 3rd transplants was associated with AMR. Since weak DSA to DPA1/DPB1 may induce acute AMR with negative FXM, donor DPA1/DPB1 high resolution typing should be considered in sensitized patients with DP-directed DSA. PMID:24755353

  8. Mutant Alleles of lptD Increase the Permeability of Pseudomonas aeruginosa and Define Determinants of Intrinsic Resistance to Antibiotics

    PubMed Central

    Grabowicz, Marcin

    2015-01-01

    Gram-negative bacteria provide a particular challenge to antibacterial drug discovery due to their cell envelope structure. Compound entry is impeded by the lipopolysaccharide (LPS) of the outer membrane (OM), and those molecules that overcome this barrier are often expelled by multidrug efflux pumps. Understanding how efflux and permeability affect the ability of a compound to reach its target is paramount to translating in vitro biochemical potency to cellular bioactivity. Herein, a suite of Pseudomonas aeruginosa strains were constructed in either a wild-type or efflux-null background in which mutations were engineered in LptD, the final protein involved in LPS transport to the OM. These mutants were demonstrated to be defective in LPS transport, resulting in compromised barrier function. Using isogenic strain sets harboring these newly created alleles, we were able to define the contributions of permeability and efflux to the intrinsic resistance of P. aeruginosa to a variety of antibiotics. These strains will be useful in the design and optimization of future antibiotics against Gram-negative pathogens. PMID:26596941

  9. [The Original Formulation for Toso-shu (Tusujiu), Created by the 3rd Century Chinese Physician, Hua Tuo].

    PubMed

    Mouri, Chika; Mikage, Masayuki

    2015-01-01

    The original formulation for "Tusujiu," which Japanese people still consume on the morning of January 1st, was created by Hua Tuo, but has not been studied in detail. The book Huatuo Shenyi Bizhuan, found in 1918, describes a concoction, "Biyijiu," that shows great similarity to the current Tusujiu; the ingredients for Biyijiu being rhubarb, atractylodes rhizome, cinnamon bark, platycodon root, zanthoxylum fruit, processed aconite root and smilax rhizome. The procedures for preparing and drinking it are to "pound the ingredients and then put them into a silk bag dyed with madder. During the daytime of the last day of the year, hang the bag in a well to soften the powder. Take the bag out early in the morning of the next day, the first day of the year. Heat the bag in fermented liquor until simmering. Drink the liquid with all family members, doing so while facing east. If one person drinks it, there will be no disease in the family. If the whole family drinks it, there will be no disease in their neighborhood in an area of one square 'li'. In this study, to determine the original formulation for Tusujiu, we examined a number of ancient medical texts from the 3rd to the 13th century that discuss Biyijiu and Tusujiu. As a result, we concluded that "Biyijiu" is likely to be the original formulation developed by Hua Tuo. PMID:26427101

  10. Organizational Support for the 3rd Summer Institute on Complex Plasmas, July 30 – August 8, 2012

    SciTech Connect

    Lopez, Jose L.

    2012-07-01

    This grant provided partial funds for American graduate students to attend the 3rd Graduate Summer Institute on Complex Plasmas, which was held from July 30 to August 8, 2012 at Seton Hall University in South Orange, New Jersey. The Graduate Summer Institute is a topical series of instructional workshops held bi-annually on the emerging field of complex plasmas that is jointly organized through a collaboration between American and German-European Union plasmas researchers. This specialized program brings together many of the world's leading researchers in the specialized area of complex plasmas, who freely provide instructional lectures and tutorials on the most recent research and discoveries done in this branch of plasma science. The partial funds provided by this grant helped support the travel and accommodation expenses of the participating American students and tutorial instructors. Partial funds further supported the travel and accommodation of three renown American plasma researchers that provided educational tutorials to the thirty-eight participating students from the United States, Europe, and Asia. The organized program afforded a unique opportunity for the participating American graduate students to learn about and engage more deeply in an area of plasma science that is not studied in any of the graduate educational curriculums provided by universities in the United States of America. The educational experience offered by this program provided the necessary knowledge needed by future American plasma researchers to keep the national plasma research effort on the cutting-edge and keep the national plasma community as a global leader.

  11. Evaluation of a model of dissertation supervision for 3rd year B.Sc. undergraduate nursing students.

    PubMed

    Scholefield, Donna; Cox, Georgina

    2016-03-01

    All English universities now offer an all degree undergraduate nursing programme. Many currently use an individual supervision model to support final year dissertation students, but with increased numbers and limited resources new models of supervision are needed. This study evaluated a mixed (group and individual) model of dissertation supervision to determine its effectiveness for a large group of undergraduate nursing students. A sample of 3rd year students and their supervisors were selected from one large university. An evaluation survey was conducted using anonymous internet-based questionnaires and focus groups. The data was analysed using Survey Monkey, SPSS and thematic analysis. A 51% (n = 56/110) response rate (students) and 65% (n = 24/37) for supervisors was obtained. The majority of students and supervisors were satisfied with the new model. There was a mixed response to the group workshops and supervision groups. Three themes emerged from the qualitative data: engaging with the process, motivation to supervise and valuing the process. The supervision process is a struggle but both parties gained considerably from going through the process. In conclusion, a mixed model of supervision together with a range of other learning resources can be an effective approach in supporting students through the dissertation process. PMID:26700648

  12. The 3rd Canadian Symposium on Hepatitis C Virus: expanding care in the interferon-free era.

    PubMed

    MacParland, Sonya A; Bilodeau, Marc; Grebely, Jason; Bruneau, Julie; Cooper, Curtis; Klein, Marina; Sagan, Selena; Choucha, Norma; Balfour, Louise; Bialystok, Frank; Krajden, Mel; Raven, Jennifer; Roberts, Eve; Russell, Rodney; Houghton, Michael; Tyrrell, D Lorne; Feld, Jordan J

    2014-10-01

    Hepatitis C virus (HCV) currently infects approximately 250,000 individuals in Canada and causes more years of life lost than any other infectious disease in the country. In August 2011, new therapies were approved by Health Canada that have achieved higher response rates among those treated, but are poorly tolerated. By 2014⁄2015, short-course, well-tolerated treatments with cure rates >95% will be available. However, treatment uptake is poor due to structural, financial, geographical, cultural and social barriers. As such, 'Barriers to access to HCV care in Canada' is a crucial topic that must be addressed to decrease HCV disease burden and potentially eliminate HCV in Canada. Understanding how to better care for HCV-infected individuals requires integration across multiple disciplines including researchers, clinical services and policy makers to address the major populations affected by HCV including people who inject drugs, baby boomers, immigrants and Aboriginal and⁄or First Nations people. In 2012, the National CIHR Research Training Program in Hepatitis C organized the 1st Canadian Symposium on Hepatitis C Virus (CSHCV) in Montreal, Quebec. The 2nd CSHCV was held in 2013 in Victoria, British Columbia. Both symposia were highly successful, attracting leading international faculty with excellent attendance leading to dialogue and knowledge translation among attendees of diverse backgrounds. The current article summarizes the 3rd CSHCV, held February 2014, in Toronto, Ontario. PMID:25314353

  13. The 3rd Canadian Symposium on Hepatitis C Virus: Expanding care in the interferon-free era

    PubMed Central

    MacParland, Sonya A; Bilodeau, Marc; Grebely, Jason; Bruneau, Julie; Cooper, Curtis; Klein, Marina; Sagan, Selena M; Choucha, Norma; Balfour, Louise; Bialystok, Frank; Krajden, Mel; Raven, Jennifer; Roberts, Eve; Russell, Rodney; Houghton, Michael; Tyrrell, D Lorne; Feld, Jordan J

    2014-01-01

    Hepatitis C virus (HCV) currently infects approximately 250,000 individuals in Canada and causes more years of life lost than any other infectious disease in the country. In August 2011, new therapies were approved by Health Canada that have achieved higher response rates among those treated, but are poorly tolerated. By 2014/2015, short-course, well-tolerated treatments with cure rates >95% will be available. However, treatment uptake is poor due to structural, financial, geographical, cultural and social barriers. As such, ‘Barriers to access to HCV care in Canada’ is a crucial topic that must be addressed to decrease HCV disease burden and potentially eliminate HCV in Canada. Understanding how to better care for HCV-infected individuals requires integration across multiple disciplines including researchers, clinical services and policy makers to address the major populations affected by HCV including people who inject drugs, baby boomers, immigrants and Aboriginal and/or First Nations people. In 2012, the National CIHR Research Training Program in Hepatitis C organized the 1st Canadian Symposium on Hepatitis C Virus (CSHCV) in Montreal, Quebec. The 2nd CSHCV was held in 2013 in Victoria, British Columbia. Both symposia were highly successful, attracting leading international faculty with excellent attendance leading to dialogue and knowledge translation among attendees of diverse backgrounds. The current article summarizes the 3rd CSHCV, held February 2014, in Toronto, Ontario. PMID:25314353

  14. 3rd Quarter Transportation Report FY 2014: Radioactive Waste Shipments to and from the Nevada National Security Site (NNSS)

    SciTech Connect

    Gregory, Louis

    2014-09-20

    This report satisfies the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO) commitment to prepare a quarterly summary report of radioactive waste shipments to the Nevada National Security Site (NNSS) Radioactive Waste Management Complex (RWMC) at Area 5. There were no shipments sent for offsite treatment and returned to the NNSS this quarter. This report summarizes the 3rd quarter of Fiscal Year (FY) 2014 low-level radioactive waste (LLW) and mixed low-level radioactive waste (MLLW) shipments. This report also includes annual summaries for FY 2014 in Tables 4 and 5. Tabular summaries are provided which include the following: Sources of and carriers for LLW and MLLW shipments to and from the NNSS; Number and external volume of LLW and MLLW shipments; Highway routes used by carriers; and Incident/accident data applicable to LLW and MLLW shipments. In this report shipments are accounted for upon arrival at the NNSS, while disposal volumes are accounted for upon waste burial. The disposal volumes presented in this report do not include minor volumes of non-radioactive materials that were approved for disposal. Volume reports showing cubic feet generated using the Low-Level Waste Information System may vary slightly due to differing rounding conventions.

  15. Effects of using relaxation breathing training to reduce music performance anxiety in 3rd to 6th graders.

    PubMed

    Su, Yu-Huei; Luh, Jer-Junn; Chen, Hsin-I; Lin, Chao-Chen; Liao, Miin-Jiun; Chen, Heng-Shuen

    2010-06-01

    The current study examined the effects of applying relaxation breathing training (RBT) as a means to reduce music performance anxiety (MPA) in young, talented musicians. A group of 59 young musicians from 3rd to 6th grade participated in this study, and all of them started RBT twice a week for 2 months prior to the examination. Four tests--2 mos, 1 mos, half an hour and 5 min before the examination--were conducted to examine the level of MPA after the application of RBT. Results show that the degree of MPA 5 min before the trial was lower than the degree of performance anxiety half an hour before the jury (t = -3.683, p < 0.01), which indicated that the RBT was associated with a decrease in MPA. Although a series of RBT exercises was applied, results indicated that when approaching the date of examination, the degree of performance anxiety still increased and reached its maximum half an hour before the jury. The recommendation for future studies is to combine the application of RBT with other methods to expand its effect in reducing MPA. PMID:20795337

  16. InAs/GaSb type II superlattices for advanced 2nd and 3rd generation detectors

    NASA Astrophysics Data System (ADS)

    Walther, Martin; Rehm, Robert; Schmitz, Johannes; Fleissner, Joachim; Rutz, Frank; Kirste, Lutz; Scheibner, Ralf; Wendler, Joachim; Ziegler, Johann

    2010-01-01

    InAs/GaSb short-period superlattices (SL) based on GaSb, InAs and AlSb have proven their great potential for high performance infrared detectors. Lots of interest is currently focused on the development of short-period InAs/GaSb SLs for advanced 2nd and 3rd generation infrared detectors between 3 - 30 μm. For the fabrication of mono- and bispectral thermal imaging systems in the mid-wavelength infrared region (MWIR) a manufacturable technology for high responsivity thermal imaging systems has been developed. InAs/GaSb short-period superlattices can be fabricated with up to 1000 periods in the intrinsic region without revealing diffusion limited behavior. This enables the fabrication of InAs/GaSb SL camera systems with high responsivity comparable to state of the art CdHgTe and InSb detectors. The material system is also ideally suited for the fabrication of dual-color MWIR/MWIR InAs/GaSb SL camera systems with high quantum efficiency for missile approach warning systems with simultaneous and spatially coincident detection in both spectral channels.

  17. Analysis of time-variant quadratic phase couplings in the tracé alternant EEG by recursive estimation of 3rd-order time-frequency distributions.

    PubMed

    Helbig, Marko; Schwab, Karin; Leistritz, Lutz; Eiselt, Michael; Witte, Herbert

    2006-10-15

    The quantification of transient quadratic phase couplings (QPC) by means of time-variant bispectral analysis is a useful approach to explain several interrelations between signal components. A generalized recursive estimation approach for 3rd-order time-frequency distributions (3rd-order TFD) is introduced. Based on 3rd-order TFD, time-variant estimations of biamplitude (BA), bicoherence (BC) and phase bicoherence (PBC) can be derived. Different smoothing windows and local moment functions for an optimization of the estimation properties are investigated and compared. The methods are applied to signal simulations and EEG signals, and it can be shown that the new time-variant bispectral analysis results in a reliable quantification of QPC in the tracé alternant EEG of healthy neonates. PMID:16737739

  18. PREFACE: Special section featuring selected papers from the 3rd International Workshop on Numerical Modelling of High Temperature Superconductors Special section featuring selected papers from the 3rd International Workshop on Numerical Modelling of High Temperature Superconductors

    NASA Astrophysics Data System (ADS)

    Granados, Xavier; Sánchez, Àlvar; López-López, Josep

    2012-10-01

    The development of superconducting applications and superconducting engineering requires the support of consistent tools which can provide models for obtaining a good understanding of the behaviour of the systems and predict novel features. These models aim to compute the behaviour of the superconducting systems, design superconducting devices and systems, and understand and test the behavior of the superconducting parts. 50 years ago, in 1962, Charles Bean provided the superconducting community with a model efficient enough to allow the computation of the response of a superconductor to external magnetic fields and currents flowing through in an understandable way: the so called critical-state model. Since then, in addition to the pioneering critical-state approach, other tools have been devised for designing operative superconducting systems, allowing integration of the superconducting design in nearly standard electromagnetic computer-aided design systems by modelling the superconducting parts with consideration of time-dependent processes. In April 2012, Barcelona hosted the 3rd International Workshop on Numerical Modelling of High Temperature Superconductors (HTS), the third in a series of workshops started in Lausanne in 2010 and followed by Cambridge in 2011. The workshop reflected the state-of-the-art and the new initiatives of HTS modelling, considering mathematical, physical and technological aspects within a wide and interdisciplinary scope. Superconductor Science and Technology is now publishing a selection of papers from the workshop which have been selected for their high quality. The selection comprises seven papers covering mathematical, physical and technological topics which contribute to an improvement in the development of procedures, understanding of phenomena and development of applications. We hope that they provide a perspective on the relevance and growth that the modelling of HTS superconductors has achieved in the past 25 years.

  19. When should orthostatic blood pressure changes be evaluated in elderly: 1st, 3rd or 5th minute?

    PubMed

    Soysal, Pinar; Aydin, Ali Ekrem; Koc Okudur, Saadet; Isik, Ahmet Turan

    2016-01-01

    Detection of orthostatic hypotension (OH) is very important in geriatric practice, since OH is associated with mortality, ischemic stroke, falls, cognitive failure and depression. It was aimed to determine the most appropriate time for measuring blood pressure in transition from supine to upright position in order to diagnose OH in elderly. Comprehensive geriatric assessment (CGA) including Head up Tilt Table (HUT) test was performed in 407 geriatric patients. Orthostatic changes were assessed separately for the 1st, 3rd and 5th minutes (HUT1, HUT3 and HUT5, respectively) taking the data in supine position as the basis. The mean age, recurrent falls, presence of dementia and Parkinson's disease, number of drugs, alpha-blocker and anti-dementia drug use, and fasting blood glucose levels were significantly higher in the patients with versus without OH; whereas, albumin and 25-hydroxy vitamin D levels were significantly lower (p<0.05). However, different from HUT3 and HUT5, Charlson Comorbidity Index and the prevalence of diabetes mellitus were higher, the use of antidiabetics, antipsychotics, benzodiazepine, opioid and levodopa were more common (p<0.05). Statistical significance of the number of drugs and fasting blood glucose level was prominent in HUT1 as compared to HUT3 (p<0.01, p<0.05). Comparison of the patients that had OH only in HUT1, HUT3or HUT5 revealed no difference in terms of CGA parameters. These results suggests that orthostatic blood pressure changes determined at the 1st minute might be more important for geriatric practice. Moreover, 1st minute measurement might be more convenient in the elderly as it requires shorter time in practice. PMID:27077324

  20. Electrocradiographic Qrs Axis, Q Wave and T-wave Changes in 2nd and 3rd Trimester of Normal Pregnancy

    PubMed Central

    S., Chandrasekharappa; Brid, S.V

    2014-01-01

    Background: Pregnancy although a physiological phenomena affects all the functions of the maternal body and brings about remarkable changes in the cardiovascular system. The cardiovascular changes and many of the physiological adaptations of normal pregnancy alter the physical findings thus, sometimes misleading the diagnosis of heart disease. Pregnancy also brings about various changes in the electrocardiogram, further confusing with that of heart disease. This study is undertaken to highlight the effect of normal pregnancy on the QRS axis, Q wave and T-wave of the Electrocardiogram and thereby helps us to distinguish it from that of pathological changes. Objectives: To study the effect of normal pregnancy on the QRS axis, Q wave and T-wave in the electrocardiogram and to compare with that of normal non pregnant women. Materials and Methods: Fifty normal pregnant women in 2nd and 3rd trimester each between 20– 35 y of age and 50 normal non pregnant women of the same age group were selected for the study. A 12 lead ECG was recorded by using ECG machine with special emphasis on QRS axis, Q wave and T-wave changes and all the parameters were analysed. Results: The ECG changes observed in our study include, deviation of QRS axis towards left as pregnancy advanced, significant increased incidence of occurrence of prominent Q waves in lead II, III and avF in pregnant group (p < 0.05 ) and, T-wave abnormalities like flat and inverted T-waves in lead III, V1 – V3 were more frequent in pregnant group ( p<0.05 ) than in non pregnant group. Conclusion:Normal pregnancy brings about various changes in ECG. These changes during pregnancy should be interpretated with caution by the physicians. It is necessary to understand the normal physiological changes which in turn help us in better management of those with cardiac disease. PMID:25386425

  1. Implications of Technology for Teaching and Learning. Annual Professional Education Seminar of Central States Colleges and Universities (3rd, November, 1967).

    ERIC Educational Resources Information Center

    Woodruff, Asahel; Froyen, Len

    This report of the proceedings of the 3rd Annual Professional Education Seminar of the Central States Colleges and Universities centers upon the implications of technology for teaching and learning and contains addresses delivered, including "Some Concerns Related to Technology in Education," by Len Froyen; and "Implications of Technology for…

  2. The Relationship between Perceived and Ideal Body Size and Body Mass Index in 3rd-Grade Low Socioeconomic Hispanic Children

    ERIC Educational Resources Information Center

    Fisher, Allison; Lange, Mary Anne; Young-Cureton, Virginia; Canham, Daryl

    2005-01-01

    Very little is known about body satisfaction among minority children. This study examined the relationship between perceived and actual body size and Body Mass Index among 43 low-socioeconomic Hispanic 3rd-graders. Researchers measured participants' Body Mass Index; students self-reported Perceived Ideal Self Image and Perceived Actual Self Image…

  3. Midwest Child-Parent Center (CPC) PreK-3rd Grade School Reform Model: Impacts on Child and Family Outcomes over Time

    ERIC Educational Resources Information Center

    Gaylor, Erika; Spiker, Donna; Wei, Xin; Lease, Erin; Reynolds, Arthur

    2015-01-01

    This presentation reports on the goals and preliminary outcomes of the Child-Parent Centers (CPC) Expansion Project, which is a PreK to 3rd grade school reform model aimed at improving the short- and long-term outcomes of participating children and families. The model provides continuous education and family support services to schools serving a…

  4. PREFACE: 3rd International Conference on Science & Engineering in Mathematics, Chemistry and Physics 2015 (ScieTech 2015)

    NASA Astrophysics Data System (ADS)

    Gaol, F. L.

    2015-06-01

    The 3rd International Conference on Science & Engineering in Mathematics, Chemistry and Physics 2015 (ScieTech 2015), was held at The Westin Resort Nusa Dua, Bali on 31 January - 1 February 2015. The ScieTech 2015 conference is aimed to bring together researchers, engineers and scientists from around the world. ScieTech 2015 is placed on promoting interaction between the theoretical, experimental, and applied communities, so that a high level exchange is achieved in new and emerging areas within mathematics, chemistry and physics. As we already know that science and technology have brought tremendous benefits for human civilization. People are becoming healthier, wealthier, better educated, more peaceful, increasingly connected, and living longer. Of course, science and technology provide many answers to global challenges, but we will face more complex problems in the next decade due to increasing world population, limitation of energy, and climate change. Therefore, researchers should be more active in conducting research that enables collaboration between one and the others. Interdisciplinary cooperation is absolutely necessary in order to create a smart system for solving the global problems. We need a global and general long-term view of the future with long-range goals for solving complex problems in next decade. Therefore the conference was held to be a forum for researchers from different disciplines to start collaborating and conducting research that provides a solution to the global issues. The theme of ScieTech 2015 was ''The interdisciplinary Application between Mathematics, Chemistry and Physics to enhance the Quality of Life''. We would like to express our sincere gratitude to all in the Technical Program Committee who have reviewed the papers and developed a very interesting conference program as well as the invited and plenary speakers. This year, we received 197 papers and after rigorous review, 59 papers were accepted. The participants came from 19

  5. Effect on Physical Activity of a Randomized Afterschool Intervention for Inner City Children in 3rd to 5th Grade

    PubMed Central

    Crouter, Scott E.; de Ferranti, Sarah D.; Whiteley, Jessica; Steltz, Sarah K.; Osganian, Stavroula K.; Feldman, Henry A.; Hayman, Laura L.

    2015-01-01

    Background Less than 45% of U.S. children meet the 60 min.d-1 physical activity (PA) guideline. Structured after-school PA programing is one approach to help increase activity levels. This study aimed to evaluate the feasibility and short-term impact of a supervised after-school PA and nutrition education program on activity levels. Methods Forty-two 3rd-5th graders from an inner-city school in Boston, MA were randomly assigned to a 10-wk after-school program of either: 1) weekly nutrition education, or 2) weekly nutrition education plus supervised PA 3 d.wk-1 at a community-based center. At baseline and follow-up, PA was measured using accelerometry and fitness (VO2max) was estimated using the PACER 15-m shuttle run. Additional measures obtained were non-fasting finger stick total cholesterol (TC) and glucose levels, waist circumference (WC), body mass index (BMI), percent body fat (%BF), and blood pressure (BP). Values are presented as mean±SE, unless noted otherwise. Results Thirty-six participants completed the study (mean±SD; age 9.7±0.9 years). Participants attended >80% of the sessions. After adjusting for accelerometer wear time and other design factors, light and moderate-to-vigorous PA (MVPA) increased in the nutrition+PA group (+21.5±14.5 and +8.6±8.0 min.d-1, respectively) and decreased in the nutrition only group (-35.2±16.3 and -16.0±9.0 min.d-1, respectively); mean difference between groups of 56.8±21.7 min.d-1 (light PA, p = 0.01) and 24.5±12.0 min.d-1 (MVPA, p = 0.04). Time spent in sedentary behaviors declined in the nutrition+PA group (-14.8±20.7 min.d-1) and increased in the nutrition only group (+55.4±23.2 min.d-1); mean difference between groups of -70.2±30.9 min.d-1 (p = 0.02). Neither group showed changes in TC, BP, WC, %BF, BMI percentile, or fitness (p>0.05). Conclusions The supervised afterschool community-based nutrition and PA program was well accepted and had high attendance. The changes in light PA and MVPA has potential

  6. PREFACE: 3rd International Conference on Geological, Geographical, Aerospace and Earth Science 2015 (AeroEarth 2015)

    NASA Astrophysics Data System (ADS)

    Gaol, F. L.

    2016-02-01

    The 3rd International Conferences on Geological, Geographical, Aerospaces and Earth Sciences 2015 (AeroEarth 2015), was held at The DoubleTree Hilton, Jakarta, Indonesia during 26 - 27 September 2015. The 1st AeoroEarth was held succefully in Jakarta in 2013. The success continued to The 2nd AeroEarth 2014 that was held in Kuta Bali, Indonesia. The publications were published by EES IOP in http://iopscience.iop.org/1755-1315/19/1 and http://iopscience.iop.org/1755-1315/23/1 respectively. The AeroEarth 2015 conference aims to bring together researchers, engineers and scientists from around the world. Through research and development, Earth's scientists have the power to preserve the planet's different resource domains by providing expert opinion and information about the forces which make life possible on Earth. The theme of AeroEarth 2015 is ''Earth and Aerospace Sciences : Challenges and Opportunities'' Earth provides resources and the exact conditions to make life possible. However, with the advent of technology and industrialization, the Earth's resources are being pushed to the brink of depletion. Non-sustainable industrial practices are not only endangering the supply of the Earth's natural resources, but are also putting burden on life itself by bringing about pollution and climate change. A major role of earth science scholars is to examine the delicate balance between the Earth's resources and the growing demands of industrialization. Through research and development, earth scientists have the power to preserve the planet's different resource domains by providing expert opinion and information about the forces which make life possible on Earth. We would like to express our sincere gratitude to all in the Technical Program Committee who have reviewed the papers and developed a very interesting Conference Program as well as the invited and plenary speakers. This year, we received 78 papers and after rigorous review, 18 papers were accepted. The participants

  7. [Use of imaging methods in the current screening, diagnostics and treatment of breast cancer - Professional guidelines. 3rd Breast Cancer Consensus Meeting].

    PubMed

    Forrai, Gábor; Ambrózay, Éva; Bidlek, Mária; Borbély, Katalin; Kovács, Eszter; Lengyel, Zsolt; Ormándi, Katalin; Péntek, Zoltán; Riedl, Erika; Sebõ, Éva; Szabó, Éva

    2016-09-01

    Breast radiologists and nuclear medical specialists have refreshed their previous statement text during the 3rd Hungarian Breast Cancer Consensus Meeting. They suggest taking into consideration this actual protocol for the screening, diagnostics and treatment of breast tumors, from now on. This recommendation includes the description of the newest technologies, the recent results of scientific research, as well as the role of imaging methods in the therapeutic processes and the follow-up. Suggestions for improvement of the Hungarian current practice and other related issues as forensic medicine, media connections, regulations, and reimbursement are also detailed. The statement text has been cross-checked with the related medical disciplines. PMID:27579719

  8. [Damage-loss relationships and integrated control of 3rd instar larvae of Actias selene nigpoana Felder in planting area of Cornus officinalis Sieb. et Zucc].

    PubMed

    Chen, S; Wang, C; Zhang, Q; Cheng, X

    1997-08-01

    In the present paper, the damage-loss model of Actias selene ningpoana to Cornus officinalis was tested and the results indicated that the yield loss rates obeyed the equation Y = 100 - EXP(4.6042 - 0.0315X). The economic threshold of the 2hd and 3rd instar larvae of A. selene nigpoana was then determined as 22 and 8 insects per tree respecitively. Suggestions for integrated control have been made based on the research of activities of A. selene ningpoana in the forest. PMID:11038910

  9. TIES for Dummies 3rd Edition (Technology Identification, Evaluation, and Selection) Basic how to's to implement the TIES method

    NASA Technical Reports Server (NTRS)

    Kirby, Michelle R.

    2002-01-01

    The TIES method is a forecasting environment whereby the decision-maker has the ability to easily assess and trade-off the impact of various technologies without sophisticated and time-consuming mathematical formulations. TIES provides a methodical approach where technically feasible alternatives can be identified with accuracy and speed to reduce design cycle time, and subsequently, life cycle costs, and was achieved through the use of various probabilistic methods, such as Response Surface Methodology and Monte Carlo Simulations. Furthermore, structured and systematic techniques are utilized from other fields to identify possible concepts and evaluation criteria by which comparisons can be made. This objective is achieved by employing the use of Morphological Matrices and Multi-Attribute Decision Making techniques. Through the execution of each step, a family of design alternatives for a given set of customer requirements can be identified and assessed subjectively or objectively. This methodology allows for more information (knowledge) to be brought into the earlier phases of the design process and will have direct implications on the affordability of the system. The increased knowledge allows for optimum allocation of company resources and quantitative justification for program decisions. Finally, the TIES method provided novel results and quantitative justification to facilitate decision making in the early stages of design so as to produce affordable and quality products.

  10. Efficacy of a 3rd generation high-throughput sequencing platform for analyses of 16S rRNA genes from environmental samples.

    PubMed

    Mosher, Jennifer J; Bernberg, Erin L; Shevchenko, Olga; Kan, Jinjun; Kaplan, Louis A

    2013-11-01

    Longer sequences of the bacterial 16S rRNA gene could provide greater phylogenetic and taxonomic resolutions and advance knowledge of population dynamics within complex natural communities. We assessed the accuracy of a Pacific Biosciences (PacBio) single molecule, real time (SMRT) sequencing based on DNA polymerization, a promising 3rd generation high-throughput technique, and compared this to the 2nd generation Roche 454 pyrosequencing platform. Amplicons of the 16S rRNA gene from a known isolate, Shewanella oneidensis MR1, and environmental samples from two streambed habitats, rocks and sediments, and a riparian zone soil, were analyzed. On the PacBio we analyzed ~500 bp amplicons that covered the V1-V3 regions and the full 1500 bp amplicons of the V1-V9 regions. On the Roche 454 we analyzed the ~500 bp amplicons. Error rates associated with the isolate were lowest with the Roche 454 method (2%), increased by more than 2-fold for the 500 bp amplicons with the PacBio SMRT chip (4-5%), and by more than 8-fold for the full gene with the PacBio SMRT chip (17-18%). Higher error rates with the PacBio SMRT chip artificially inflated estimates of richness and lowered estimates of coverage for environmental samples. The 3rd generation sequencing technology we evaluated does not provide greater phylogenetic and taxonomic resolutions for studies of microbial ecology. PMID:23999276

  11. Effect of non-erupted 3rd molars on distal roots and supporting structures of approximal teeth. A radiographic survey of 202 cases.

    PubMed

    Nemcovsky, C E; Libfeld, H; Zubery, Y

    1996-09-01

    Root resorption of 2nd molars in proximity to non-erupted 3rd molars has been widely reported. The purpose of this study was to determine the prevalence of root resorption in second molars adjacent to non-erupted third molars. Its association to age and gender of the patient, location and inclination of the non-erupted third molar and to distal bone support of the 2nd molars was analyzed. A radiographic survey of 202 periapical radiographs taken in patients with clinically missing third molars was conducted. 3 examiners independently evaluated the radiographs and only those cases where at least 2 observers agreed were included in this report. Statistical analysis was performed on 186 radiographs. Associations were analyzed with the Pearson chi 2 test. Radiographic evidence of root resorption was found in 45 2nd molars (24.2%) of which 12 (6.5%) showed moderate to complete root resorption. Non-erupted tooth apical position and mesio-inclination of 60 degrees or more relative to the distal root of the second molar were significantly associated with root resorption (p = 0.01368 and p = 0.0194, respectively). Resorption was positively associated with age of patient (p = 0.00606). These results may support early extraction of impacted 3rd molars especially in cases with a mesio-angulation of 60 degrees or more and an apical location in proximity to the distal root of the 2nd molar. PMID:8891930

  12. Future perspectives in melanoma research: meeting report from the "Melanoma Bridge": Napoli, December 3rd-6th 2014.

    PubMed

    Ascierto, Paolo A; Atkins, Michael; Bifulco, Carlo; Botti, Gerardo; Cochran, Alistair; Davies, Michael; Demaria, Sandra; Dummer, Reinhard; Ferrone, Soldano; Formenti, Silvia; Gajewski, Thomas F; Garbe, Claus; Khleif, Samir; Kiessling, Rolf; Lo, Roger; Lorigan, Paul; Arthur, Grant Mc; Masucci, Giuseppe; Melero, Ignacio; Mihm, Martin; Palmieri, Giuseppe; Parmiani, Giorgio; Puzanov, Igor; Romero, Pedro; Schilling, Bastian; Seliger, Barbara; Stroncek, David; Taube, Janis; Tomei, Sara; Zarour, Hassane M; Testori, Alessandro; Wang, Ena; Galon, Jérôme; Ciliberto, Gennaro; Mozzillo, Nicola; Marincola, Francesco M; Thurin, Magdalena

    2015-01-01

    survival rates have also been observed with immune-targeted therapy for patients with metastatic melanoma. Immune-modulating antibodies came to the forefront with anti-CTLA-4, programmed cell death-1 (PD-1) and PD-1 ligand 1 (PD-L1) pathway blocking antibodies that result in durable responses in a subset of melanoma patients. Agents targeting other immune inhibitory (e.g., Tim-3) or immune stimulating (e.g., CD137) receptors and other approaches such as adoptive cell transfer demonstrate clinical benefit in patients with melanoma as well. These agents are being studied in combination with targeted therapies in attempt to produce longer-term responses than those more typically seen with targeted therapy. Other combinations with cytotoxic chemotherapy and inhibitors of angiogenesis are changing the evolving landscape of therapeutic options and are being evaluated to prevent or delay resistance and to further improve survival rates for this patient population. This meeting's specific focus was on advances in combination of targeted therapy and immunotherapy. Both combination targeted therapy approaches and different immunotherapies were discussed. Similarly to the previous meetings, the importance of biomarkers for clinical application as markers for diagnosis, prognosis and prediction of treatment response was an integral part of the meeting. The overall emphasis on biomarkers supports novel concepts toward integrating biomarkers into contemporary clinical management of patients with melanoma across the entire spectrum of disease stage. Translation of the knowledge gained from the biology of tumor microenvironment across different tumors represents a bridge to impact on prognosis and response to therapy in melanoma. PMID:26619946

  13. Deuterium beam acceleration with 3rd harmonic ion cyclotron resonance heating in Joint European Torus: Sawtooth stabilization and Alfvén eigenmodes

    NASA Astrophysics Data System (ADS)

    Gassner, T.; Schoepf, K.; Sharapov, S. E.; Kiptily, V. G.; Pinches, S. D.; Hellesen, C.; Eriksson, J.; JET-EFDA contributors

    2012-03-01

    Experiments on accelerating NBI-produced deuterium (D) beam ions from their injection energy of ˜110 keV up to the MeV energy range with 3rd harmonic ion cyclotron resonance heating were performed on the Joint European Torus [P. H. Rebut and B. E. Keen, Fusion Technol. 11, 13 (1987)]. A renewed set of nuclear diagnostics was used for analysing fast D ions during sawtooth stabilization, monster sawtooth crashes, and during excitation of Alfvén eigenmodes (AEs) residing inside the q = 1 radius. The measurements and modeling of the fast ions with the nonlinear HAGIS code [S. D. Pinches et al., Comput. Phys. Commun. 111, 133 (1998)] show that monster sawtooth crashes are strongly facilitated by the AE-induced re-distribution of the fast D ions from inside the q = 1 radius to the plasma edge.

  14. [Pathological diagnosis, work-up and reporting of breast cancer. Recommendations of the 3rd Hungarian Consensus Conference on Breast Cancer].

    PubMed

    Cserni, Gábor; Kulka, Janina; Francz, Monika; Járay, Balázs; Kálmán, Endre; Kovács, Ilona; Krenács, Tibor; Udvarhelyi, Nóra; Vass, László

    2016-09-01

    There have been relevant changes in the diagnosis and treatment of breast cancer to implement the updating of the 2010 recommendations made during the 2nd national consensus conference on the disease. Following a wide interdisciplinary consultation, the present recommendations have been finalized after their public discussion at the 3rd Hungarian Consensus Conference on Breast Cancer. The recommendations cover non-operative and intraoperative diagnostics, the work-up of operative specimens, the determination of prognostic and predictive markers and the content of the cytology and histology reports. Furthermore, it touches some special issues such as the current status of multigene molecular markers, the role of pathologists in clinical trials and prerequisites for their involvement, some relevant points about the future. PMID:27579721

  15. From challenges to solutions. European Bioanalysis Forum 3rd Annual Open Symposium, Hesperia Towers, Barcelona, Spain, 1-3 December 2010.

    PubMed

    Abbott, Richard W; Gordon, Ben; van Amsterdam, Peter; Lausecker, Berthold; Brudny-Kloeppel, Margarete; Smeraglia, John; Romero, Fernando; Globig, Susanne; Golob, Michaela; Knutsson, Magnus; Herling, Christian; Vieser, Eva; Timmerman, Philip

    2011-04-01

    The European Bioanalysis Forum is a bioanalytical nonprofit organization comprised of European pharmaceutical companies (27 members to date) and currently expanding to include CROs as well. The European Bioanalysis Forum provides a broad European bioanalytical network for the discussion of scientific, technological and regulatory topics of bioanalytical interest. The 3rd Annual Open Symposium was again much anticipated after the two previous successful meetings. The symposium included sessions on thinking outside the 'commodity' box, bioanalytical challenges with blood, global harmonization, assay platforms, dried blood spots, immunogenicity, matrix effects, anomalous results, biomarkers and two plenary technology sessions hosted by the Platinum sponsors. Experts and key opinion leaders were invited as guest speakers. A total of 424 delegates registered from 113 companies representing a large percentage of the European bioanalytical community. In addition to 48 oral presentations, 88 posters were presented and there was a vendor exposition of 40 companies. PMID:21510756

  16. Reflections: Surgical Education-the Times they are a-Changin': Lessons Learned from the 3rd MAYMET-ESO Joint Meeting.

    PubMed

    Tarkowski, Radoslaw; Vetto, John T

    2015-09-01

    Technical skills are not sufficient for successful surgical care. Non-technical skills such as team work, decision-making in cancer treatment, communication with the patient, ethical challenges, situation awareness, and communication in the operating room are mandatory for favorable outcomes. Although formally taught in other high-demand disciplines, such skills were traditionally rarely discussed in surgical oncology. The 3rd MAYMET-ESO Joint Meeting "Professionalism for Breast Surgeons" held in Istanbul, Turkey, 5 October 2013 was dedicated to the development of non-technical skills in the everyday activity of breast surgeons. We briefly discuss information from this very interesting and inspiring educational event and how it relates to more recent changes in surgical oncology education. PMID:25903052

  17. Adaptive and Effortful Control and Academic Self-efficacy Beliefs on Achievement: A Longitudinal Study of 1st through 3rd Graders

    PubMed Central

    Liew, Jeffrey; McTigue, Erin; Barrois, Lisa; Hughes, Jan

    2009-01-01

    The linkages between self-regulatory processes and achievement were examined across three years in 733 children beginning at 1st grade (M = 6.57 years, SD = .39 at 1st grade) who were identified as lower achieving in literacy. Accounting for consistencies in measures (from one year prior) and for influences of child’s age, gender, IQ, ethnicity and economic adversity on achievement, results indicate that adaptive/effortful control at 1st grade contributed to both academic self-efficacy beliefs at 2nd grade, and reading (but not math) achievement at 3rd grade. Although academic self-efficacy did not partially mediate the linkage between adaptive/effortful control and achievement, academic self-efficacy beliefs were positively correlated with reading and math. Results support the notion that early efforts to promote children’s self-regulatory skills would enhance future academic self-beliefs and achievement, particularly in literacy. PMID:19169387

  18. Limbic system development underlies the emergence of classical fear conditioning during the 3rd and 4th weeks of life in the rat

    PubMed Central

    Deal, Alex L.; Erickson, Kristen J.; Shiers, Stephanie I.; Burman, Michael A.

    2016-01-01

    Classical fear conditioning creates an association between an aversive stimulus and a neutral stimulus. Although the requisite neural circuitry is well understood in mature organisms, the development of these circuits is less well studied. The current experiments examine the ontogeny of fear conditioning and relate it to neuronal activation assessed through immediate early gene (IEG) expression in the amygdala, hippocampus, perirhinal cortex, and hypothalamus of periweanling rats. Rat pups were fear conditioned, or not, during the 3rd or 4th weeks of life. Neuronal activation was assessed by quantifying expression of FBJ osteosarcoma oncogene (FOS) using immunohistochemistry (IHC) in Experiment 1. Fos and early growth response gene-1 (EGR1) expression was assessed using qRT-PCR in Experiment 2. Behavioral data confirm that both auditory and contextual fear continue to emerge between PD 17 and 24. The IEG expression data are highly consistent with these behavioral results. IHC results demonstrate significantly more FOS protein expression in the basal amygdala of fear conditioned PD 23 subjects compared to control subjects, but no significant difference at PD 17. qRT-PCR results suggest specific activation of the amygdala only in older subjects during auditory fear expression. A similar effect of age and conditioning status was also observed in the perirhinal cortex during both contextual and auditory fear expression. Overall, the development of fear conditioning occurring between the 3rd and 4th weeks of life appears to be at least partly attributable to changes in activation of the amygdala and perirhinal cortex during fear conditioning or expression. PMID:26820587

  19. Knowledge and institutional requirements to promote land degradation neutrality in drylands - An analysis of the outcomes of the 3rd UNCCD scientific conference

    NASA Astrophysics Data System (ADS)

    Akhtar-Schuster, Mariam; Safriel, Uriel; Abraham, Elena; de Vente, Joris; Essahli, Wafa; Escadafal, Richard; Stringer, Lindsay

    2015-04-01

    Achieving land degradation neutrality (LDN) through sustainable land management (SLM) targets the maintenance or restoration of the productivity of land, and therefore has to include decision-makers, knowledge generators and knowledge holders at the different relevant geographic scales. In order to enhance the implementation of the Convention, the Conference of the Parties (COP) of the United Nations Convention to Combat Desertification therefore decided that each future session of its Committee on Science and Technology (CST) would be organized in a predominantly scientific and technical conference-style format. This contribution will outline the major outcomes of UNCCD's 3rd scientific conference that will be held in Cancún, Mexico, from 9 to 12 March 2015, on addressing desertification, land degradation and drought issues (DLDD) for poverty reduction and sustainable development. The conference follows an exceptional new round table conference format that will allow the various stakeholders to discuss scientific as well as the contribution of traditional knowledge and practices in combating land degradation. This format should provide two-way communication and enable deeper insight into the availability and contribution of all forms of knowledge for achieving LDN through the assessment of: • the vulnerability of lands to DLDD and climate change and the adaptive capacities of socio-ecosystems; • best examples of adapted, knowledge-based practices and technologies; • monitoring and assessment methods to evaluate the effectiveness of adaptation practices and technologies. The outcomes of UNCCD's 3rd scientific conference will serve as a basis for discussing: • contributions of science to diagnose the status of land; • research gaps that need to be addressed to achieve LDN for poverty reduction; • additional institutional requirements to optimally bridge knowledge generation, knowledge maintenance and knowledge implementation at the science

  20. Veterinary Microbiology, 3rd Edition

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Veterinary Microbiology, Third Edition is organized into four sections and begins with an updated and expanded introductory section on infectious disease pathogenesis, diagnosis and clinical management. The second section covers bacterial and fungal pathogens, and the third section describes viral d...

  1. Landman's encyclopedia. 3rd edition

    SciTech Connect

    Hankinson, R.L.; Hankinson, R.L. Jr.

    1987-01-01

    This book discusses the guidelines for petroleum landmen and includes the new documents: partial assignment of oil, gas, and mineral lease, net profits agreement, net profit interest, ratification agreements, an additional farmout agreement form, gas balancing agreement, shut-in gas royalty, oil, gas, and mineral lease form (Exxon lease), extension agreement, Pugh clause, assignment form of lease and equipment, losses addendum for operating agreements, boundary agreement, change of lease description forms. Also included is a cross-listing of the document numbers used in this book with those used in the popular software database.

  2. A Kinesthetic Learning Approach to Earth Science for 3rd and 4th Grade Students on the Pajarito Plateau, Los Alamos, NM

    NASA Astrophysics Data System (ADS)

    Wershow, H. N.; Green, M.; Stocker, A.; Staires, D.

    2010-12-01

    Current efforts towards Earth Science literacy in New Mexico are guided by the New Mexico Science Benchmarks [1]. We are geoscience professionals in Los Alamos, NM who believe there is an important role for non-traditional educators utilizing innovative teaching methods. We propose to further Earth Science literacy for local 3rd and 4th grade students using a kinesthetic learning approach, with the goal of fostering an interactive relationship between the students and their geologic environment. We will be working in partnership with the Pajarito Environmental Education Center (PEEC), which teaches the natural heritage of the Pajarito Plateau to 3rd and 4th grade students from the surrounding area, as well as the Family YMCA’s Adventure Programs Director. The Pajarito Plateau provides a remarkable geologic classroom because minimal structural features complicate the stratigraphy and dramatic volcanic and erosional processes are plainly on display and easily accessible. Our methodology consists of two approaches. First, we will build an interpretive display of the local geology at PEEC that will highlight prominent rock formations and geologic processes seen on a daily basis. It will include a simplified stratigraphic section with field specimens and a map linked to each specimen’s location to encourage further exploration. Second, we will develop and implement a kinesthetic curriculum for an exploratory field class. Active engagement with geologic phenomena will take place in many forms, such as a scavenger hunt for precipitated crystals in the vesicles of basalt flows and a search for progressively smaller rhyodacite clasts scattered along an actively eroding canyon. We believe students will be more receptive to origin explanations when they possess a piece of the story. Students will be provided with field books to make drawings of geologic features. This will encourage independent assessment of phenomena and introduce the skill of scientific observation. We

  3. The perceptions of professional soccer players on the risk of injury from competition and training on natural grass and 3rd generation artificial turf

    PubMed Central

    2014-01-01

    Background The purpose of this study was to describe professional soccer players’ perceptions towards injuries, physical recovery and the effect of surface related factors on injury resulting from soccer participation on 3rd generation artificial turf (FT) compared to natural grass (NG). Methods Information was collected through a questionnaire that was completed by 99 professional soccer players from 6 teams competing in Major League Soccer (MLS) during the 2011 season. Results The majority (93% and 95%) of the players reported that playing surface type and quality influenced the risk of sustaining an injury. Players believed that playing and training on FT increased the risk of sustaining a non-contact injury as opposed to a contact injury. The players identified three surface related risk factors on FT, which they related to injuries and greater recovery times: 1) Greater surface stiffness 2) Greater surface friction 3) Larger metabolic cost to playing on artificial grounds. Overall, 94% of the players chose FT as the surface most likely to increase the risk of sustaining an injury. Conclusions Players believe that the risk of injury differs according to surface type, and that FT is associated with an increased risk of non-contact injury. Future studies should be designed prospectively to systematically track the perceptions of groups of professional players training and competing on FT and NG. PMID:24581229

  4. Sunphotometric Measurement of Columnar H2O and Aerosol Optical Depth During the 3rd Water Vapor IOP in Fall 2000 at the SGP ARM Site

    NASA Technical Reports Server (NTRS)

    Schmid, B; Eilers, J. A.; McIntosh, D. M.; Longo, K.; Livingston, J. M.; Redemann, J.; Russell, P. B.; Braun, J.; Rocken, C.; Hipskind, R. Stephen (Technical Monitor)

    2001-01-01

    We conducted ground-based measurements with the Ames Airborne Tracking 6-channel Sunphotometer (AATS-6) during the 3rd Water Vapor IOP (WVIOP3), September 18 - October 8, 2000 at the SGP ARM site. For this deployment our primary result was columnar water vapor (CWV) obtained from continuous solar transmittance measurements in the 0.94-micron band. In addition, we simultaneously measured aerosol optical depth (AOD) at 380, 450, 525, 864 and 1020 nm. During the IOP, preliminary results of CWV and AOD were displayed in real-time. The result files were made available to other investigators by noon of the next day. During WVIOP3 those data were shown on the daily intercomparison plots on the IOP web-site. Our preliminary results for CWV fell within the spread of values obtained from other techniques. After conclusion of WVIOP3, AATS-6 was shipped directly to Mauna Loa, Hawaii for post-mission calibration. The updated calibration, a cloud screening technique for AOD, along with other mostly cosmetic changes were applied to the WVIOP3 data set and released as version 0.1. The resulting changes in CWV are small, the changes in AOD and Angstrom parameter are more noticeable. Data version 0.1 was successfully submitted to the ARM External Data Center. In the poster we will show data examples for both CWV and AOD. We will also compare our CWV results with those obtained from a GPS (Global Positioning System) slant path method.

  5. Stable Isotope and Trace Element Studies on Gladiators and Contemporary Romans from Ephesus (Turkey, 2nd and 3rd Ct. AD) - Implications for Differences in Diet

    PubMed Central

    Lösch, Sandra; Moghaddam, Negahnaz; Grossschmidt, Karl; Risser, Daniele U.; Kanz, Fabian

    2014-01-01

    The gladiator cemetery discovered in Ephesus (Turkey) in 1993 dates to the 2nd and 3rd century AD. The aim of this study is to reconstruct diverse diet, social stratification, and migration of the inhabitants of Roman Ephesus and the distinct group of gladiators. Stable carbon, nitrogen, and sulphur isotope analysis were applied, and inorganic bone elements (strontium, calcium) were determined. In total, 53 individuals, including 22 gladiators, were analysed. All individuals consumed C3 plants like wheat and barley as staple food. A few individuals show indication of consumption of C4 plants. The δ13C values of one female from the gladiator cemetery and one gladiator differ from all other individuals. Their δ34S values indicate that they probably migrated from another geographical region or consumed different foods. The δ15N values are relatively low in comparison to other sites from Roman times. A probable cause for the depletion of 15N in Ephesus could be the frequent consumption of legumes. The Sr/Ca-ratios of the gladiators were significantly higher than the values of the contemporary Roman inhabitants. Since the Sr/Ca-ratio reflects the main Ca-supplier in the diet, the elevated values of the gladiators might suggest a frequent use of a plant ash beverage, as mentioned in ancient texts. PMID:25333366

  6. Evidence of human-induced morphodynamic changes along the Campania coastal areas (southern Italy) since the 3rd-4th cent. AD

    NASA Astrophysics Data System (ADS)

    Russo Ermolli, Elda; Romano, Paola; Liuzza, Viviana; Amato, Vincenzo; Ruello, Maria Rosaria; Di Donato, Valentino

    2014-05-01

    Campania has always offered suitable climatic and physiographic conditions for human settlements since prehistoric times. In particular, many Graeco-Roman towns developed along its coasts starting from the 7th-6th cent. BC. In the last decade, geoarchaelogical surveys have been carried out in the archaeological excavations of Neapolis, Paestum and Elea-Velia allowing the main steps of the landscape evolution around these towns to be defined in detail. The greek town of Neapolis rose in the late 6th cent. BC [1] on a terrace overlooking a low-relief rocky coast surrounded by volcanic hills. Port activities developed in a protected bay facing the town from the 4th-2nd cent. BC up to the 4th cent. AD, as testified by the discovery of structures and shipwrecks [2, 3, 4]. Starting from the 3rd cent. AD a spit bar formed at the bay entrance causing the progressive establishment of a lagoon which was gradually filled up by alluvial inputs and completely closed in the 5th cent. AD. During the same period, episodes of increased alluvial inputs were also recorded further west along the coast, where a narrow sandy beach formed at the cliff toe. The greek town of Poseidonia, renamed Paestum by the Romans, was founded in the 540 BC on a travertine terrace facing the sandy littoral of a prograding coastal plain [5]. In front of the main town door, a coastal lagoon developed thanks to the growth of a dune ridge and was probably used for harbor activities [5]. After this period the shoreline shifted seawards, another dune ridge formed and the back-ridge depression was filled with fluvial-marshy deposits, slowly drying up. Phases of travertine deposition, which characterized the SE sector of the plain all along the Holocene, were recorded in the northern and southern quarters of the town in historical times and were connected to the abandonment of the town in the early Medieval times. The greek colony of Elea-Velia was located on top of a siliciclastic promontory where the ruins of

  7. Stellar Occultations by Large TNOs on 2012: The February 3rd by (208996) 2003 AZ84, and the February 17th by (50000) Quaoar

    NASA Astrophysics Data System (ADS)

    Braga Ribas, Felipe; Sicardy, B.; Ortiz, J. L.; Duffard, R.; Camargo, J. I. B.; Lecacheux, J.; Colas, F.; Vachier, F.; Tanga, P.; Sposetti, S.; Brosch, N.; Kaspi, S.; Manulis, I.; Baug, T.; Chandrasekhar, T.; Ganesh, S.; Jain, J.; Mohan, V.; Sharma, A.; Garcia-Lozano, R.; Klotz, A.; Frappa, E.; Jehin, E.; Assafin, M.; Vieira Martins, R.; Behrend, R.; Roques, F.; Widemann, T.; Morales, N.; Thirouin, A.; Mahasena, P.; Benkhaldoun, Z.; Daassou, A.; Rinner, C.; Ofek, E. O.

    2012-10-01

    On February 2012, two stellar occultation's by large Trans-neptunian Objects (TNO's) were observed by our group. On the 3rd, an event by (208996) 2003 AZ84 was recorded from Mont Abu Observatory and IUCAA Girawali Observatory in India and from Weizmann Observatory in Israel. On the 17th, a stellar occultation by (50000) Quaoar was observed from south France and Switzerland. Both occultations are the second observed by our group for each object, and will be used to improve the results obtained on the previous events. The occultation by 2003 AZ84 is the first multi-chord event recorded for this object. From the single chord event on January 8th 2011, Braga-Ribas et al. 2011 obtained a lower limit of 573 +/- 21 km. From the 2012 occultation the longest chord has a size of 662 +/- 50 km. The other chords will permit to determine the size and shape of the TNO, and derive other physical parameters, such as the geometric albedo. The Quaoar occultation was observed from south of France (Observatoire de la Côte d'Azur, TAROT telescope and Valensole) and from Gnosca, Switzerland. Unfortunately, all three sites in France are almost at the same Quaoar's latitude, so in practice, we have two chords that can be used to fit Quaoar's limb. The resulting fit will be compared with the results obtained by Braga-Ribas et al. 2011. Braga-Ribas F., Sicardy B., et al. 2011, EPSC-DPS2011, 1060.Ribas F., Sicardy B., et al. 2011, EPSC-DPS2011, 1060.

  8. Medical school curriculum characteristics associated with intentions and frequency of tobacco dependence treatment among 3rd year U.S. medical students

    PubMed Central

    Hayes, Rashelle B.; Geller, Alan C.; Crawford, Sybil L.; Jolicoeur, Denise; Churchill, Linda C.; Okuyemi, Kola; David, Sean P.; Adams, Michael; Waugh, Jonathan; Allen, Sharon S.; Leone, Frank T.; Fauver, Randy; Leung, Katherine; Liu, Qin; Ockene, Judith K.

    2015-01-01

    Objective Physicians play a critical role in addressing tobacco dependence, yet report limited training. Tobacco dependence treatment curricula for medical students could improve performance in this area. This study identified student and medical school tobacco treatment curricula characteristics associated with intentions and use of the 5As for tobacco treatment among 3rd year U.S. medical students. Methods Third year medical students (N=1065, 49.3% male) from 10 U.S. medical schools completed a survey in 2009-2010 assessing student characteristics, including demographics, tobacco treatment knowledge, and self-efficacy. Tobacco curricula characteristics assessed included amount and type of classroom instruction, frequency of tobacco treatment observation, instruction, and perception of preceptors as role models. Results Greater tobacco treatment knowledge, self-efficacy, and curriculum-specific variables were associated with 5A intentions, while younger age, tobacco treatment self-efficacy, intentions, and each curriculum-specific variable was associated with greater 5A behaviors. When controlling for important student variables, greater frequency of receiving 5A instruction (OR = 1.07; 95%CI 1.01-1.12) and perception of preceptors as excellent role models in tobacco treatment (OR = 1.35; 95%CI 1.04-1.75) were significant curriculum predictors of 5A intentions. Greater 5A instruction (B = .06 (.03); p< .05) and observation of tobacco treatment (B= .35 (.02); p< .001) were significant curriculum predictors of greater 5A behaviors. Conclusions Greater exposure to tobacco treatment teaching during medical school is associated with both greater intentions to use and practice tobacco 5As. Clerkship preceptors, or those physicians who provide training to medical students, may be particularly influential when they personally model and instruct students in tobacco dependence treatment. PMID:25572623

  9. US Marine 3rd Tank Battalion lubrication evaluation under hot ambient temperatures at Twenty-Nine Palms, California. Interim report, April-September 1988

    SciTech Connect

    Butler, W.E.; Owens, E.C.; Frame, E.A.; Bowen, T.C.

    1988-09-01

    Military Specification MIL-L-2104D, Lubricating Oil, Internal Combustion Engines, Tactical Service, was released 1 April 1983. This specification included a multiviscosity OE/HDO-15/40 oil and eliminated a previously authorized OE/HDO-50 oil. The manufacturer of the AVDS-1790 series engines used in M60 battle tanks and M88 tank retrievers raised raised concerns about warranty coverage. The U.S. Marine Corps indicated that the use of the authorized 15W-40 grade oil did not offer sufficient lubrication for the engines and also resulted in M60 final drive leaks. As a result of these concerns, the U.S. Army Belvoir Research, Development and Engineering Center (Belvoir RDE Center) authorized an oil comparison test that, by agreement with the U.S. Marine Corps, would be conducted at the U.S. Marine Corps Air-Ground Combat Center (USMCAGCC) at Twenty-Nine Palms, CA using the U.S. Marine 3rd Tank Battalion (3DTKBn). The test vehicles of A Company, 3DTKBn were charged with regular issue 50-grade oil in the engine, 10-grade oil in the transmission, and 50-grade oil in the M60 final drives. B Company's test vehicles were charged with 15W-40 grade oil in the engines, transmissions, and M60 final drives. C Company's test vehicles were charged with 40-grade oil in the engines, 10-grade oil in the transmissions, and 50-grade oil in the final drives. Results from this 4-month test indicated no discernible differences in engine or transmission operating temperatures, engine oil pressures, or M60 final drive leaks.

  10. Non-destructive measurement of demineralization and remineralization in the occlusal pits and fissures of extracted 3rd molars with PS-OCT

    NASA Astrophysics Data System (ADS)

    Lee, Chulsung; Hsu, Dennis J.; Le, Michael H.; Darling, Cynthia L.; Fried, Daniel

    2009-02-01

    Previous studies have demonstrated that Polarization Sensitive Optical Coherence Tomography (PS-OCT) can be used to image the remineralization of early artificial caries lesion on smooth enamel surfaces of human and bovine teeth. However, most new dental decay is found in the pits and fissures of the occlusal surfaces of posterior dentition and it is in these high risk areas where the performance of new caries imaging devices need to be investigated. The purpose of this study was to demonstrate that PS-OCT can be used to measure the subsequent remineralization of artificial lesions produced in the pits and fissures of extracted 3rd molars. A PS-OCT system operating at 1310-nm was used to acquire polarization resolved images of occlusal surfaces exposed to a demineralizing solution at pH-4.5 followed by a fluoride containing remineralizing solution at pH-7.0 containing 2-ppm fluoride. The integrated reflectivity was calculated to a depth of 200-µm in the entire lesion area using an automated image processing algorithm. Although a well-defined surface zone was clearly resolved in only a few of the samples that underwent remineralization, the PS-OCT measurements indicated a significant (p<0.05) reduction in the integrated reflectivity between the severity of the lesions that were exposed to the remineralization solution and those that were not. The lesion depth and mineral loss were also measured with polarized light microscopy and transverse microradiography after sectioning the teeth. These results show that PS-OCT can be used to non-destructively monitor the remineralization potential of anti-caries agents in the important pits and fissures of the occlusal surface.

  11. A novel amperometric alcohol biosensor developed in a 3rd generation bioelectrode platform using peroxidase coupled ferrocene activated alcohol oxidase as biorecognition system.

    PubMed

    Chinnadayyala, Somasekhar R; Kakoti, Ankana; Santhosh, Mallesh; Goswami, Pranab

    2014-05-15

    Alcohol oxidase (AOx) with a two-fold increase in efficiency (Kcat/Km) was achieved by physical entrapment of the activator ferrocene in the protein matrix through a simple microwave based partial unfolding technique and was used to develop a 3rd generation biosensor for improved detection of alcohol in liquid samples. The ferrocene molecules were stably entrapped in the AOx protein matrix in a molar ratio of ~3:1 through electrostatic interaction with the Trp residues involved in the functional activity of the enzyme as demonstrated by advanced analytical techniques. The sensor was fabricated by immobilizing ferrocene entrapped alcohol oxidase (FcAOx) and sol-gel chitosan film coated horseradish peroxidase (HRP) on a multi-walled carbon nanotube (MWCNT) modified glassy carbon electrode through layer-by-layer technique. The bioelectrode reactions involved the formation of H2O2 by FcAOx biocatalysis of substrate alcohol followed by HRP-catalyzed reduction of the liberated H2O2 through MWCNT supported direct electron transfer mechanism. The amperometric biosensor exhibited a linear response to alcohol in the range of 5.0 × 10(-6) to 30 × 10(-4)mol L(-1) with a detection limit of 2.3 × 10(-6) mol L(-1), and a sensitivity of 150 µA mM(-1) cm(-2). The biosensor response was steady for 28 successive measurements completed in a period of 5h and retained ~90% of the original response even after four weeks when stored at 4 °C. The biosensor was successfully applied for the determination of alcohol in commercial samples and its performance was validated by comparing with the data obtained by GC analyses of the samples. PMID:24368229

  12. Metabolic engineering of E.coli for the production of a precursor to artemisinin, an anti-malarial drug [Chapter 25 in Manual of Industrial Microbiology and Biotechnology, 3rd edition

    SciTech Connect

    Petzold, Christopher; Keasling, Jay

    2011-07-18

    This document is Chapter 25 in the Manual of Industrial Microbiology and Biotechnology, 3rd edition. Topics covered include: Incorporation of Amorpha-4,11-Diene Biosynthetic Pathway into E. coli; Amorpha-4,11-Diene Pathway Optimization; "-Omics" Analyses for Increased Amorpha-4,11-Diene Production; Biosynthetic Oxidation of Amorpha-4,11-Diene.

  13. ICOM2012: 3rd International Conference on the Physics of Optical Materials and Devices (Belgrade, Serbia, 2-6 September 2012)

    NASA Astrophysics Data System (ADS)

    Dramićanin, Miroslav D.; Antić, Željka; Viana, Bruno

    2013-11-01

    The 3rd International Conference on the Physics of Optical Materials and Devices (ICOM2012) was held in Belgrade (Serbia) from 2 to 6 September 2012 (figure 1). The conference was organized by the Vinča Institute of Nuclear Sciences, University of Belgrade (Serbia) and the Laboratoire de Chimie de la Matière Condensée de Paris (France), and supported by the Ministry of Education, Science and Technological Development of the Republic of Serbia and Optical Society of America. ICOM2012 was a follow-up to the two previous, successful ICOM conferences held in Herceg Novi in 2006 and 2009. The conference aimed at providing a forum for scientists in optical materials to debate on: • Luminescent materials and nanomaterials • Hybrid optical materials (organic/inorganic) • Characterization techniques of optical materials • Luminescence mechanisms and energy transfers • Theory and modeling of optical processes • Ultrafast-laser processing of materials • Optical sensors • Medical imaging • Advanced optical materials in photovoltaics and biophotonics • Photothermal and photoacoustic spectroscopy and phenomena The conference stressed the value of a fundamental scientific understanding of optical materials. A particular accent was put on wide band-gap materials in crystalline, glass and nanocrystalline forms. The applications mainly involved lasers, scintillators and phosphors. Rare earth and transition metal ions introduced as dopants in various hosts were considered, and their impact on the optical properties were detailed in several presentations. This volume contains selected contributions of speakers and participants of the ICOM2012 conference. The conference provided a unique opportunity for about 200 scientists from 32 countries to discuss recent progress in the field of optical materials. During the three and half days, 21 invited talks and 52 contributed lectures were given, with a special event in memory of our dear colleague Professor Dr Tsoltan

  14. [Cold agglutinin disease -  no response to glucocorticoids and rituximab, what treatment is best for the 3rd line of therapy? Case report and review of the literature].

    PubMed

    Adam, Z; Pejchalová, A; Chlupová, G; Ríhová, L; Pour, L; Krejčí, M; Cervinek, L; Král, Z; Mayer, J

    2013-09-01

    in about one  half of treated patients and the remission duration median after rituximab administration is 11 months. A combination of rituximab with fludarabin was more effective, though more toxic; this combination, in a clinical study, led to 75% of patients responding to treatment, including 20% experiencing complete remission. The treatment response median reached over 66 months. In a small study (10 patients) an increase in the amount of rituximab administrations from 4 to 8 led to a treatment response in 6 patients in whom administration of 4 doses of rituximab had no response. When treating Waldenström macroglobulinemia, effectiveness of the following drugs and their combinations was proven: rituximab, chlorambucil, cyclophosphamide, fludarabin, bortezomib, lenalidomid, bendamustin and alemtuzumab. The same drugs and treatment procedures are used for the treatment of the cold agglutinin disease as for Waldenström macroglobulinemia. Successful treatment with vortezomibem, combinations of rituximab + bendamustin, rituximab + cyclophosphamide or rituximab + fludarabin + cyclophosphamide, were recorded in the form of a description as regards the cold agglutinin disease treatment. An important benefit is also shown through treatment with the monoclonal antibody antiC5, eculizumab, which is otherwise used for the treatment of paroxysmal nocturnal haemoglobinuria. Eculizumab blocks the C5 element of the component and thus stops haemolysis in a patient with cold agglutinin disease. As cold agglutinin disease is very rare, there are only a few clinical studies and when treating this rare disease we have no other option than to take into account the information contained in the descriptions of the particular cases of cold agglutinin disease and the experience of Waldenström macroglobulinemia disease treatment. The discussion seeks to solve the issue regarding what 3rd line treatment option to use in the described patient. PMID:24073955

  15. Joint conference of iMEC 2015 (2nd International Manufacturing Engineering Conference & APCOMS 2015 (3rd Asia-Pacific Conference on Manufacturing Systems)

    NASA Astrophysics Data System (ADS)

    2016-02-01

    The iMEC 2015 is the second International Manufacturing Engineering Conference organized by the Faculty of Manufacturing, Universiti Malaysia Pahang (UMP), held from 12-14th November 2015 in Kuala Lumpur, Malaysia, with a theme "Materials, Manufacturing and Systems for Tomorrow". For the first time, iMEC is organized together with 3rd Asia- Pacific Conference on Manufacturing System (APCOMS 2015) which owned by Fakulti Teknologi Industri, Institut Teknologi Bandung (ITB), Indonesia. This is an extended collaboration between UMP and ITB to intensify knowledge sharing and experiences between higher learning institutions. This conference (iMEC & APCOMS 2015) is a platform for knowledge exchange and the growth of ideas, particularly in manufacturing engineering. The conference aims to bring researchers, academics, scientists, students, engineers and practitioners from around the world together to present their latest findings, ideas, developments and applications related to manufacturing engineering and other related research areas. With rapid advancements in manufacturing engineering, iMEC is an appropriate medium for the associated community to keep pace with the changes. In 2015, the conference theme is “Materials, Manufacturing and Systems for Tomorrow” which reflects the acceleration of knowledge and technology in global manufacturing. The papers in these proceedings are examples of the work presented at the conference. They represent the tip of the iceberg, as the conference attracted over 200 abstracts from Malaysia, Indonesia, Japan, United Kingdom, Australia, India, Bangladesh, South Africa, Turkey and Morocco and 151 full papers were accepted in these proceedings. The conference was run in four parallel sessions with 160 presenters sharing their latest finding in the areas of manufacturing process, systems, advanced materials and automation. The first keynote presentation was given by Prof. B. S. Murthy (IIT, Madras) on "Nanomaterials with Exceptional

  16. Rosse, 3rd Earl of [William Parsons, Lord Rosse, Lord Oxmantown] (1800-67) and Rosse, 4th Earl of [Laurence Parsons, Lord Rosse, Lord Oxmantown] (1840-1908)

    NASA Astrophysics Data System (ADS)

    Murdin, P.

    2000-11-01

    Irish astronomer and landowner, the 3rd Lord Rosse was educated at Trinity College, Dublin and Oxford as a mathematician. He became interested in astronomy and made at the family castle in Birr a 36 in reflector with the same design as William Herschel's (see HERSCEL FAMILY). Mapped the Moon, and observed nebulae with the intent to resolve them into stars. He developed the technology at Birr Cast...

  17. Image Quality of 3rd Generation Spiral Cranial Dual-Source CT in Combination with an Advanced Model Iterative Reconstruction Technique: A Prospective Intra-Individual Comparison Study to Standard Sequential Cranial CT Using Identical Radiation Dose

    PubMed Central

    Wenz, Holger; Maros, Máté E.; Meyer, Mathias; Förster, Alex; Haubenreisser, Holger; Kurth, Stefan; Schoenberg, Stefan O.; Flohr, Thomas; Leidecker, Christianne; Groden, Christoph; Scharf, Johann; Henzler, Thomas

    2015-01-01

    Objectives To prospectively intra-individually compare image quality of a 3rd generation Dual-Source-CT (DSCT) spiral cranial CT (cCT) to a sequential 4-slice Multi-Slice-CT (MSCT) while maintaining identical intra-individual radiation dose levels. Methods 35 patients, who had a non-contrast enhanced sequential cCT examination on a 4-slice MDCT within the past 12 months, underwent a spiral cCT scan on a 3rd generation DSCT. CTDIvol identical to initial 4-slice MDCT was applied. Data was reconstructed using filtered backward projection (FBP) and 3rd-generation iterative reconstruction (IR) algorithm at 5 different IR strength levels. Two neuroradiologists independently evaluated subjective image quality using a 4-point Likert-scale and objective image quality was assessed in white matter and nucleus caudatus with signal-to-noise ratios (SNR) being subsequently calculated. Results Subjective image quality of all spiral cCT datasets was rated significantly higher compared to the 4-slice MDCT sequential acquisitions (p<0.05). Mean SNR was significantly higher in all spiral compared to sequential cCT datasets with mean SNR improvement of 61.65% (p*Bonferroni0.05<0.0024). Subjective image quality improved with increasing IR levels. Conclusion Combination of 3rd-generation DSCT spiral cCT with an advanced model IR technique significantly improves subjective and objective image quality compared to a standard sequential cCT acquisition acquired at identical dose levels. PMID:26288186

  18. A novel mutation in Prph2, a gene regulated by Nr2e3, causes retinal degeneration and outer segment defects similar to Nr2e3rd7/rd7 retinas

    PubMed Central

    Nystuen, Arne M.; Sachs, Andrew J.; Yuan, Yang; Heuermann, Laura; Haider, Neena B.

    2014-01-01

    The nmf193 mutant was generated by a large-scale ENU mutagenesis screen and originally described as having a dominantly inherited phenotype characterized by fundus abnormalities. We determined that nmf193 mice exhibit outer segment defects and progressive retinal degeneration. Clinical examination revealed retinal spotting apparent at 6 weeks of age. Histological analysis of homozygous mutant mice at 6 weeks indicated an absence of outer segments (OS) and a 50% reduction of photoreceptor cells which progressed to complete loss of photoreceptors by 10 months. Mice heterozygous for the nmf193 mutation had a less severe phenotype of shortened outer segments at 2 months with progressive loss of photoreceptor cells to 50% by 10 months. A positional cloning approach using a DNA pooling strategy was performed to identify the causative mutation in nmf193 mice. The nmf193 mutation linked to chromosome 17 and fine mapped to an interval containing the peripherin/rds (Prph2) gene. Mutation analysis identified a single base change in Prph2 that causes aberrant splicing between exon 1 and 2. Interestingly, a comparative histological analysis demonstrated that Prph2nmf193/+ mutants have similar photoreceptor degeneration to that of Nr2e3rd7/rd7. We show that Prph2 mRNA and protein levels are reduced in the Nr2e3rd7/rd7 mutant compared to control littermates. Further, chromatin immunoprecipitation analysis shows that Prph2 is a direct target of NR2E3. In addition, the down-regulation of Prph2 gene expression is similar in both the Nr2e3rd7/rd7 and Prph2nmf193/+ mutants suggesting that the reduction of Prph2 may contribute to the degenerative pathology seen in Nr2e3rd7/rd7. PMID:18763016

  19. Stage-based mortality of grassland grasshoppers (Acrididae) from wandering spider (Lycosidae) predation

    NASA Astrophysics Data System (ADS)

    Oedekoven, Mark A.; Joern, Anthony

    1998-12-01

    Mortality rates in insects, including grasshoppers (Acrididae), are often stage- or size-specific. We estimated stage-specific mortality rates for three common grasshopper species from a Nebraska (USA) sandhills grassland ( Ageneotettix deorum, Melanoplus sanguinipes and Phoetaliotes nebrascensis), and partitioned the impact due to wandering spider predation from remaining sources. Survivorship was estimated for multiple developmental stages (3rd instar through adult) under experimental conditions that either prevented or permitted predation from free-living, wandering spiders (primarily Schizocosa species). Total stage-specific mortality, including spider predation, examined over the period of single stages was greatest for the youngest stages (91% for 3rd instar, 73% for 4th instar, 63.5% for 5th instar and 30.4% for adults). For the developmental stages considered and averaged for all species, the contribution to total mortality from spider predation over the 10-d period (approximately the length of a developmental stage) ranged from 17% for 3rd instar nymphs to 23% for 4th and 5th instars, and an undetectable level for adults. While spiders may depress grasshopper numbers, contributions from spider predation to grasshopper population dynamics are uncertain.

  20. Effects of Deep Water Source-Sink Terms in 3rd generation Wave Model SWAN using different wind data in Black Sea

    NASA Astrophysics Data System (ADS)

    Kirezci, Cagil; Ozyurt Tarakcioglu, Gulizar

    2016-04-01

    Coastal development in Black Sea has increased in recent years. Therefore, careful monitoring of the storms and verification of numerical tools with reliable data has become important. Previous studies by Kirezci and Ozyurt (2015) investigated extreme events in Black Sea using different wind datasets (NCEP's CFSR and ECMWF's operational datasets) and different numerical tools (SWAN and Wavewatch III). These studies showed that significant effect to results is caused by the deep water source-sink terms (wave growth by wind, deep water dissipation of wave energy (whitecapping) and deep water non-linear wave-wave interactions). According to Timmermans(2015), uncertainty about wind forcing and the process of nonlinear wave-wave interactions are found to be dominant in numerical wave modelling. Therefore, in this study deep water source and sink term solution approaches of 3rd generation numerical tool (SWAN model) are tested, validated and compared using the selected extreme storms in Black Sea. 45 different storms and storm like events observed in Black Sea between years 1994-1999 are selected to use in the models. The storm selection depends on the instrumental wave data (significant wave heights, mean wave period and mean wave direction) obtained in NATO-TU Waves project by the deep water buoy measurements at Hopa, Sinop, Gelendzhik, and wind data (mean and peak wind speeds, storm durations) of the regarding events. 2 different wave growth by wind with the corresponding deep water dissipation terms and 3 different wave -wave interaction terms of SWAN model are used in this study. Wave growth by wind consist of two parts, linear growth which is explained by Cavaleri and Malanotte-Rizzoli(1981),and dominant exponential growth. There are two methods in SWAN model for exponential growth of wave, first one by Snyder et al. (1981), rescaled in terms of friction velocity by Komen et. al (1984) which is derived using driving wind speed at 10m elevation with related drag

  1. Effects of Deep Water Source-Sink Terms in 3rd generation Wave Model SWAN using different wind data in Black Sea

    NASA Astrophysics Data System (ADS)

    Kirezci, Cagil; Ozyurt Tarakcioglu, Gulizar

    2016-04-01

    Coastal development in Black Sea has increased in recent years. Therefore, careful monitoring of the storms and verification of numerical tools with reliable data has become important. Previous studies by Kirezci and Ozyurt (2015) investigated extreme events in Black Sea using different wind datasets (NCEP's CFSR and ECMWF's operational datasets) and different numerical tools (SWAN and Wavewatch III). These studies showed that significant effect to results is caused by the deep water source-sink terms (wave growth by wind, deep water dissipation of wave energy (whitecapping) and deep water non-linear wave-wave interactions). According to Timmermans(2015), uncertainty about wind forcing and the process of nonlinear wave-wave interactions are found to be dominant in numerical wave modelling. Therefore, in this study deep water source and sink term solution approaches of 3rd generation numerical tool (SWAN model) are tested, validated and compared using the selected extreme storms in Black Sea. 45 different storms and storm like events observed in Black Sea between years 1994-1999 are selected to use in the models. The storm selection depends on the instrumental wave data (significant wave heights, mean wave period and mean wave direction) obtained in NATO-TU Waves project by the deep water buoy measurements at Hopa, Sinop, Gelendzhik, and wind data (mean and peak wind speeds, storm durations) of the regarding events. 2 different wave growth by wind with the corresponding deep water dissipation terms and 3 different wave -wave interaction terms of SWAN model are used in this study. Wave growth by wind consist of two parts, linear growth which is explained by Cavaleri and Malanotte-Rizzoli(1981),and dominant exponential growth. There are two methods in SWAN model for exponential growth of wave, first one by Snyder et al. (1981), rescaled in terms of friction velocity by Komen et. al (1984) which is derived using driving wind speed at 10m elevation with related drag

  2. [Study on the age-hardenable silver alloy (3 rd report). III. On the ageing process of dental Ag-Pd-Cu-Au alloy (author's transl)].

    PubMed

    Ota, M; Hisatsune, K; Yamane, M

    1975-05-01

    The precipitation hardening process of a dental silver base alloy, Ag-28 Pd-10 Cu-12 wt % Au, was studied by means of X-ray diffraction, hardness measurement and metallographic observations. After solution treatment at 900 degrees C for 30 min, specimens were subjected to anisothermal annealing at the rate of 1 degrees C/min. PdCu ordered phase and alpha2 solid solution (Ag rich phase) precipitated hetelogeneously at the grain boundaries and then grew up into each grain. Drastic increase in hardness was recognized with the spread of nodular region. Electron microscopic observation of these precipitates showed very fine lamellar structure. It is concluded that the age hardening of this alloy could be attributed to this grain boundary precipitation and the softening at the overaged stage to the second grain boundary reaction which produced very coarse lamellar structure. PMID:1058263

  3. Stage design

    DOEpatents

    Shacter, J.

    1975-12-01

    A method is described of cycling gases through a plurality of diffusion stages comprising the steps of admitting the diffused gases from a first diffusion stage into an axial compressor, simultaneously admitting the undiffused gases from a second diffusion stage into an intermediate pressure zone of said compressor corresponding in pressure to the pressure of said undiffused gases, and then admitting the resulting compressed mixture of diffused and undiffused gases into a third diffusion stage.

  4. The ENCCA-WP7/EuroSarc/EEC/PROVABES/EURAMOS 3rd European Bone Sarcoma Networking Meeting/Joint Workshop of EU Bone Sarcoma Translational Research Networks; Vienna, Austria, September 24-25, 2015. Workshop Report.

    PubMed

    Kager, Leo; Whelan, Jeremy; Dirksen, Uta; Hassan, Bass; Anninga, Jakob; Bennister, Lindsey; Bovée, Judith V M G; Brennan, Bernadette; Broto, Javier M; Brugières, Laurence; Cleton-Jansen, Anne-Marie; Copland, Christopher; Dutour, Aurélie; Fagioli, Franca; Ferrari, Stefano; Fiocco, Marta; Fleuren, Emmy; Gaspar, Nathalie; Gelderblom, Hans; Gerrand, Craig; Gerß, Joachim; Gonzato, Ornella; van der Graaf, Winette; Hecker-Nolting, Stefanie; Herrero-Martín, David; Klco-Brosius, Stephanie; Kovar, Heinrich; Ladenstein, Ruth; Lancia, Carlo; LeDeley, Marie-Cecile; McCabe, Martin G; Metzler, Markus; Myklebost, Ola; Nathrath, Michaela; Picci, Piero; Potratz, Jenny; Redini, Françoise; Richter, Günther H S; Reinke, Denise; Rutkowski, Piotr; Scotlandi, Katia; Strauss, Sandra; Thomas, David; Tirado, Oscar M; Tirode, Franck; Vassal, Gilles; Bielack, Stefan S

    2016-01-01

    This report summarizes the results of the 3rd Joint ENCCA-WP7, EuroSarc, EEC, PROVABES, and EURAMOS European Bone Sarcoma Network Meeting, which was held at the Children's Cancer Research Institute in Vienna, Austria on September 24-25, 2015. The joint bone sarcoma network meetings bring together European bone sarcoma researchers to present and discuss current knowledge on bone sarcoma biology, genetics, immunology, as well as results from preclinical investigations and clinical trials, to generate novel hypotheses for collaborative biological and clinical investigations. The ultimate goal is to further improve therapy and outcome in patients with bone sarcomas. PMID:27315524

  5. PREFACE: MEM05: The 3rd International Workshop on Mechano-Electromagnetic Properties of Composite Superconductors (Kyoto, Japan, 17 20 July 2005)

    NASA Astrophysics Data System (ADS)

    Osamura, Kozo; Hampshire, Damian

    2005-12-01

    One of the important challenges facing the international scientific community at the beginning of the third millennium is how to manage the world's energy resources properly. Superconductivity will provide one of the strategies employed to avoid an energy crisis. Of course the ITER Fusion Tokomak that is to be built in France provides an exciting focus for the whole superconductivity community. In parallel, we can expect that other key technologies for superconductivity such as large capacity transmission cables, energy storage systems, and generators and motors will have a real impact in technologically advanced countries. There is broadly a consensus that the prototype stage for high-current high-field superconducting applications is largely completed, and the required performance has been demonstrated. However, before we move to full industrialization of large-scale superconducting technologies, feasibility studies suggest there are two types of problem that remain. The first is the development of high performance and low cost materials which are fully optimized in terms of critical current, low ac loss and high strength. The second is the establishment of optimal procedures for system design accompanying scale up. As the system design is dependent on material development, there is a critical need to study the key issues for developing high performance superconducting materials. Under the activities of the NEDO Grant Project (Applied Superconductivity), MEM05 was organized by Professor Osamura (Kyoto University), Professor Itoh (NIMS), Professor Hojo (Kyoto University) and Professor Matsumoto (Kyoto University) and held in Kyoto, Japan. The focus for the workshop was the elimination of grain boundary weak links, the creation of strong flux pinning sites, the optimal arrangement of filaments and barriers for reducing ac losses, and the design of high strength strain tolerant composite conductors. Five subsessions were held at MEM05. • Mechanical properties of

  6. Third Stage

    NASA Video Gallery

    Once the third stage finishes its work, Kepler will have sufficient energy to leave the gravitational pull of Earth and go into orbit around the Sun, trailing behind Earth and slowly drifting away ...

  7. Comprehensive risk reduction in patients with atrial fibrillation: emerging diagnostic and therapeutic options--a report from the 3rd Atrial Fibrillation Competence NETwork/European Heart Rhythm Association consensus conference.

    PubMed

    Kirchhof, Paulus; Lip, Gregory Y H; Van Gelder, Isabelle C; Bax, Jeroen; Hylek, Elaine; Kaab, Stefan; Schotten, Ulrich; Wegscheider, Karl; Boriani, Giuseppe; Brandes, Axel; Ezekowitz, Michael; Diener, Hans; Haegeli, Laurent; Heidbuchel, Hein; Lane, Deirdre; Mont, Luis; Willems, Stephan; Dorian, Paul; Aunes-Jansson, Maria; Blomstrom-Lundqvist, Carina; Borentain, Maria; Breitenstein, Stefanie; Brueckmann, Martina; Cater, Nilo; Clemens, Andreas; Dobrev, Dobromir; Dubner, Sergio; Edvardsson, Nils G; Friberg, Leif; Goette, Andreas; Gulizia, Michele; Hatala, Robert; Horwood, Jenny; Szumowski, Lukas; Kappenberger, Lukas; Kautzner, Josef; Leute, Angelika; Lobban, Trudie; Meyer, Ralf; Millerhagen, Jay; Morgan, John; Muenzel, Felix; Nabauer, Michael; Baertels, Christoph; Oeff, Michael; Paar, Dieter; Polifka, Juergen; Ravens, Ursula; Rosin, Ludger; Stegink, W; Steinbeck, Gerhard; Vardas, Panos; Vincent, Alphons; Walter, Maureen; Breithardt, Günter; Camm, A John

    2012-01-01

    While management of atrial fibrillation (AF) patients is improved by guideline-conform application of anticoagulant therapy, rate control, rhythm control, and therapy of accompanying heart disease, the morbidity and mortality associated with AF remain unacceptably high. This paper describes the proceedings of the 3rd Atrial Fibrillation NETwork (AFNET)/European Heart Rhythm Association (EHRA) consensus conference that convened over 60 scientists and representatives from industry to jointly discuss emerging therapeutic and diagnostic improvements to achieve better management of AF patients. The paper covers four chapters: (i) risk factors and risk markers for AF; (ii) pathophysiological classification of AF; (iii) relevance of monitored AF duration for AF-related outcomes; and (iv) perspectives and needs for implementing better antithrombotic therapy. Relevant published literature for each section is covered, and suggestions for the improvement of management in each area are put forward. Combined, the propositions formulate a perspective to implement comprehensive management in AF. PMID:21791573

  8. Comprehensive risk reduction in patients with atrial fibrillation: emerging diagnostic and therapeutic options—a report from the 3rd Atrial Fibrillation Competence NETwork/European Heart Rhythm Association consensus conference

    PubMed Central

    Kirchhof, Paulus; Lip, Gregory Y.H.; Van Gelder, Isabelle C.; Bax, Jeroen; Hylek, Elaine; Kaab, Stefan; Schotten, Ulrich; Wegscheider, Karl; Boriani, Giuseppe; Brandes, Axel; Ezekowitz, Michael; Diener, Hans; Haegeli, Laurent; Heidbuchel, Hein; Lane, Deirdre; Mont, Luis; Willems, Stephan; Dorian, Paul; Aunes-Jansson, Maria; Blomstrom-Lundqvist, Carina; Borentain, Maria; Breitenstein, Stefanie; Brueckmann, Martina; Cater, Nilo; Clemens, Andreas; Dobrev, Dobromir; Dubner, Sergio; Edvardsson, Nils G.; Friberg, Leif; Goette, Andreas; Gulizia, Michele; Hatala, Robert; Horwood, Jenny; Szumowski, Lukas; Kappenberger, Lukas; Kautzner, Josef; Leute, Angelika; Lobban, Trudie; Meyer, Ralf; Millerhagen, Jay; Morgan, John; Muenzel, Felix; Nabauer, Michael; Baertels, Christoph; Oeff, Michael; Paar, Dieter; Polifka, Juergen; Ravens, Ursula; Rosin, Ludger; Stegink, W.; Steinbeck, Gerhard; Vardas, Panos; Vincent, Alphons; Walter, Maureen; Breithardt, Günter; Camm, A. John

    2012-01-01

    While management of atrial fibrillation (AF) patients is improved by guideline-conform application of anticoagulant therapy, rate control, rhythm control, and therapy of accompanying heart disease, the morbidity and mortality associated with AF remain unacceptably high. This paper describes the proceedings of the 3rd Atrial Fibrillation NETwork (AFNET)/European Heart Rhythm Association (EHRA) consensus conference that convened over 60 scientists and representatives from industry to jointly discuss emerging therapeutic and diagnostic improvements to achieve better management of AF patients. The paper covers four chapters: (i) risk factors and risk markers for AF; (ii) pathophysiological classification of AF; (iii) relevance of monitored AF duration for AF-related outcomes; and (iv) perspectives and needs for implementing better antithrombotic therapy. Relevant published literature for each section is covered, and suggestions for the improvement of management in each area are put forward. Combined, the propositions formulate a perspective to implement comprehensive management in AF. PMID:21791573

  9. Lucky guess or knowledge: a cross-sectional study using the Bland and Altman analysis to compare confidence-based testing of pharmacological knowledge in 3rd and 5th year medical students.

    PubMed

    Kampmeyer, Daniela; Matthes, Jan; Herzig, Stefan

    2015-05-01

    Multiple-choice-questions are common in medical examinations, but guessing biases assessment results. Confidence-based-testing (CBT) integrates indicated confidence levels. It has been suggested that correctness of and confidence in an answer together indicate knowledge levels thus determining the quality of a resulting decision. We used a CBT approach to investigate whether decision quality improves during undergraduate medical education. 3rd- and 5th-year students attended formative multiple-choice exams on pharmacological issues. Students were asked to indicate their confidence in a given answer. Correctness of answers was scored binary (1-correct; 0-wrong) and confidence levels were transformed to an ordinal scale (guess: 0; rather unsure: 0.33; rather sure: 0.66; very sure: 1). 5th-year students gave more correct answers (73 ± 16 vs. 49 ± 13 %, p < 0.05) and were on average more confident regarding the correctness of their answers (0.61 ± 0.18 vs. 0.46 ± 0.13, p < 0.05). Correlation of these parameters was stronger for 5th-year students (r = 0.81 vs. r = 0.52), but agreement of confidence and correctness ('centration') was lower. By combining the Bland-and-Altman approach with categories of decision-quality we found that 5th-year students were more likely to be 'well-informed' (41 vs. 5 %), while more 3rd-students were 'uninformed' (24 vs. 76 %). Despite a good correlation of exam results and confidence in given answers increased knowledge might be accompanied by a more critical view at the own abilities. Combining the statistical Bland-and-Altman analysis with a theoretical approach to decision-quality, more advanced students are expected to apply correct beliefs, while their younger fellows are rather at risk to hesitate or to act amiss. PMID:25103688

  10. Real-World Use of 3rd Line Therapy for Multiple Myeloma in Austria: An Austrian Myeloma Registry (AMR) Analysis of the Therapeutic Landscape and Clinical Outcomes prior to the Use of Next Generation Myeloma Therapeutics

    PubMed Central

    Willenbacher, Ella; Weger, Roman; Rochau, Ursula; Siebert, Uwe; Willenbacher, Wolfgang

    2016-01-01

    Objective Clinical trials demonstrate improving survival in patients with multiple myeloma (MM) after treatment. However, it is unclear whether increased survival translates to a similar benefit in a real world setting. Methods We analyzed the overall survival of 347 multiple myeloma patients in Austria by means of a national registry (AMR), focused on results from 3rd and later lines of therapy. This benchmark was chosen to define a baseline prior to the broad application of upcoming 2nd generation drugs (carfilzomib, pomalidomide). Results Projected 10 years survival for patients with MM in Austria is estimated to be 56% in patients diagnosed in between the years 2011–2014, 21% in patients with a diagnosis made between 2000–2005, and 39% in those with a diagnosis made between 2006–2010). For the same intervals a significant increase in the use of both bortezomib, lenalidomide and thalidomide—so called IMiDs (from 2005 onwards) and their simultaneous use in combination therapies (from 2010 onwards) could be shown. The use of autologous transplantation (ASCT) remained more or less constant at ~ 35% of patients in the 1st line setting over the whole period, comparing well to international practice patterns, while the use of 2nd line ASCT increased from 5.5% to 18.7% of patients. Patients in 3rd or later line treatment (n = 105), showed that even in relapsed and refractory disease median survival was 27 months with a considerable proportion of long-term survivors (~20%). Conclusion & Perspective With the expected emergence of additional active anti-myeloma compounds, we aim to assess survival in patients with relapsed and refractory MM. PMID:26937956

  11. Fundamentals of nuclear pharmacy, 3rd Ed

    SciTech Connect

    Saha, G.B. )

    1992-01-01

    This book is a standard text/reference of nuclear pharmacy. New sections in the Third Edition include: instruments used for radiation detection and measurement; disposal of radioactive materials; clinical uses of all new and existing radiopharmaceuticals; 99m Tc and 123I-labeled radiopharmaceuticals, as well as radiolabeled leukocytes, platelets, and antibodies; and up-to-date descriptions of the latest FDA regulations.

  12. Cerebral computed tomography, 3rd Edition

    SciTech Connect

    Weisberg, L.; Nice, C.

    1988-01-01

    This book is an introduction to the utilization of computed tomography in evaluating patients with intracranial and orbital disorders. It features clinical correlations and provides an overview of general principles, performance, and normal anatomy of CT. It covers evaluation of specific neurologic signs and symptoms, including stroke, metastatic disease, increased intracranial pressure, head injury, pediatric conditions, and more.

  13. Towards a hydrogen economy. 3rd ed.

    SciTech Connect

    2006-07-15

    The report is a study of the movement towards using hydrogen as a key energy carrier in the future. It takes a look at the current state of hydrogen and addresses the infrastructure requirements needed to make the hydrogen economy a reality. The report offers a detailed look at the move to a hydrogen economy by: Identifying the current status of hydrogen production and use; Discussing the key business drivers of the move towards hydrogen; Discussing the barriers to implementation that stand in the way of a transition; Providing a critical look at whether the hydrogen economy can succeed; Describing the options that exist for a hydrogen infrastructure; Identifying the key government initiatives making the hydrogen economy a reality; Providing company-by-company profiles of automobile manufacturer efforts to develop and commercialize hydrogen vehicles; and Providing profiles of key hydrogen infrastructure manufacturers.

  14. Teaching Visually Impaired Children. 3rd Edition

    ERIC Educational Resources Information Center

    Bishop, Virginia E.

    2004-01-01

    In this exceptional new third edition, the author has retained much of the practical "how to" approach of the previous editions, but adds depth in two dimensions: learning theory and the educational process. This book is "so comprehensive in scope and complete in detail that it would be the most likely recommended" (from the foreword by Dr.…

  15. A Beginning. Revised 3rd Edition.

    ERIC Educational Resources Information Center

    Healy, Mary K.; Root, Phyllis

    This document contains a selection of materials focusing on man acting to know, preserve, and improve his environment. The booklet is divided into three parts. Part one presents a listing of objectives. They reflect a need for all to become aware of the problems that plague our environment. Furthermore, they indicate that the ecological…

  16. Coal mine ground control. 3rd ed.

    SciTech Connect

    Peng, S.S.

    2008-09-15

    The third edition not only completely revises and updates the original subject areas, but also is broadened to include a number of new topics such as high horizontal stresses, computer modeling, and highwall stability. The subject areas covered in this book define the current field of coal mine ground control, except for the recently emerging topic of mine seals and some conventional subjects such as coal/rock cutting and impoundment dams. It contains 1,134 references from all published sources, and archived since 1876.

  17. Elementary Science Guide -- 3rd Grade.

    ERIC Educational Resources Information Center

    Wieland, Anne; And Others

    Presented is a resource book to be used with instructional kits for elementary school science students, grade 3. The individual units at this grade level are based on curriculum which has been developed by the National Science Foundation in the 1960s and revised to meet student and teacher identified needs in Anchorage, Alaska. Six units are…

  18. Presenting the 3rd edition of WRB

    NASA Astrophysics Data System (ADS)

    Schad, Peter

    2014-05-01

    The third edition of the international soil classification system "World Reference Base for Soil Resources" (WRB) will be presented during der 20th World Congress of Soil Science, Jeju, Korea, June 9-12. The second edition was published in 2006 and the first in 1998, which, in turn, was based on the Legends of the FAO Soil Map of the World. Now, after eight years of experience with the second edition, time was due for a revision. The major changes are: 1. The second edition had two different qualifier sequences for naming soils (IUSS Working Group WRB, 2006, update 2007) and for creating map legends (Guidelines for creating small-scale map legends using the WRB; IUSS Working Group WRB, 2010). The third edition has one sequence for both. The qualifiers for every Reference Soil Group are subdivided into a small number of main qualifiers that are ranked and a larger number of additional qualifiers that are not ranked and given in an alphabetical order. The name of a pedon must comprise all applying qualifiers. The name of a map unit comprises a specified small number of main qualifiers, depending on scale, whereas all other qualifiers are optional. 2. For some soils, problems have been reported. Albeluvisols are difficult to detect in the field and cover only small surfaces. They have been replaced by Retisols, which have a broader definition that is easier to identify in the field. 3. The use of some diagnostics was difficult. Examples are: The argic horizon had too low limit values, so we had much more soils with argic horizons than justified. The definitions of the cambic horizon and the gleyic and stagnic properties were not precise enough. Organic material, mollic and umbric horizons had an unnecessary complicated definition. 4. Some changes in the key to the Reference Soil Groups seemed to be justified. Fluvisols were moved further down, Durisols and Gypsisols switched their position, also Arenosols and Cambisols. The soils with an argic horizon were brought into a new sequence. 5. The umbrella function of WRB aims to allow the allocation of soil classes existing in a national classification system within the WRB. Characteristics that in a national system are regarded to be important must be considered in WRB - not necessarily at the highest level, but at least somewhere. The third edition of WRB allows a better accommodation of soil types, e.g., of the Australian and the Brazilian system. 6. Some environments or even ecoregions had not been well represented in WRB. The third edition allows a better accommodation of soils of ultra-continental permafrost regions, acid-sulphate soils and Technosols. 7. How to explain complicated sets of characteristics? For the third edition, efforts were made to give better structured definitions that can be more easily grasped. The editors of the third edition are convinced that the new WRB allows a more precise classification of soils including both, a better naming of pedons and a better elaboration of soil map legends.

  19. The Physics of Glaciers, 3rd Edition

    NASA Astrophysics Data System (ADS)

    Bahr, David

    At one time or another, who among us has not marveled at the beauty of the snow and ice-covered Alps, or admired the tenacity of polar explorers and the adventurous spirits of climbers on the glacier-clad summits of the high Himalaya? The fascination of distant ice covered expanses has enlisted more than a few recruits into the ranks of glaciologists, but many, if not most, of today's students of glaciology are a slightly less romantic and more mathematical lot, attracted by the quantitative world of physics and the applied sciences of polar climatology, ice mechanics, and snow hydrology.Once a relatively quiet branch of geophysics filled with venturesome climbers capable of reaching the objects of their study, glaciology is now a field that is fueled by a rapid influx of talent, technology, and new ideas due to the increasingly acknowledged relationships between global climate, sea level, and ice sheets. While the understanding of glacier processes has seen significant progress, as a result there is also a sense of being overwhelmed by the voluminous and sometimes speculative theories and field observations associated with an expanding discipline.

  20. The 3rd International Microgravity Combustion Workshop

    NASA Technical Reports Server (NTRS)

    Ross, Howard D. (Compiler)

    1995-01-01

    This Conference Publication contains 71 papers presented at the Third International Microgravity Combustion Workshop held in Cleveland, Ohio, from April 11 to 13, 1995. The purpose of the workshop was twofold: to exchange information about the progress and promise of combustion science in microgravity and to provide a forum to discuss which areas in microgravity combustion science need to be expanded profitably and which should be included in upcoming NASA Research Announcements (NRA).

  1. Radiation Therapy Physics, 3rd Edition

    NASA Astrophysics Data System (ADS)

    Hendee, William R.; Ibbott, Geoffrey S.; Hendee, Eric G.

    2004-08-01

    The Third Edition of Radiation Therapy Physics addresses in concise fashion the fundamental diagnostic radiologic physics principles as well as their clinical implications. Along with coverage of the concepts and applications for the radiation treatment of cancer patients, the authors have included reviews of the most up-to-date instrumentation and critical historical links. The text includes coverage of imaging in therapy planning and surveillance, calibration protocols, and precision radiation therapy, as well as discussion of relevant regulation and compliance activities. It contains an updated and expanded section on computer applications in radiation therapy and electron beam therapy, and features enhanced user-friendliness and visual appeal with a new, easy-to-follow format, including sidebars and a larger trim size. With its user-friendly presentation and broad, comprehensive coverage of radiotherapy physics, this Third Edition doubles as a medical text and handy professional reference.

  2. Clear air handbook. 3rd edition

    SciTech Connect

    Brownell, F.W.

    1998-07-01

    The Clean Air Act is the most complex piece of environmental legislation ever enacted, and it is constantly evolving. Regulatory proceedings to implement the act and especially the 1990 amendments are ongoing. Further amendments to the act are being considered by Congress. In addition to developing new rules, EPA also continues to supplement existing rules with guidance documents and policy statements--materials critical to evaluating your company's compliance obligations. This book not only continues to provide a broad overview of all the complex regulatory requirements but also brings you up-to-date on all of the most recent developments. Chapters covered include The Federal-State Partnership; The 1990 Amendments; Air Quality Regulations, State Implementation Plans, and the Non-Attainment Program; Control Technology Regulation; Operating and Pre-Construction Permitting Programs; Acid Deposition Control Program; Hazardous Air Pollutants; Regulation of Mobile Sources of Air Pollution; Stratospheric Ozone Protection; Enforcement and Judicial Review; and Current Regulatory and Legislative Trends.

  3. Library Research Workbook. 3rd Edition, Revised.

    ERIC Educational Resources Information Center

    Hitchings, Donna, Ed.; And Others

    Designed to be used in an English course at the University of Houston, this library skills workbook includes lessons and multiple-choice exercises on the following topics: (1) a floor plan of the main university library; (2) catalog records; (3) catalog access points; (4) using the catalogs; (5) locating books; (6) encyclopedias; (7) dictionaries;…

  4. Peace Corps. 3rd Annual Report.

    ERIC Educational Resources Information Center

    Peace Corps, Washington, DC.

    Projects, operations, and future plans are covered in this annual report for the third year of the Peace Corps. An introduction comments on returning volunteers and presents regional maps with tables for Latin America, Africa, Near East and South Asia, and Far East. Section 1 contains letters and reports from volunteers in Peru, Ivory Coast,…

  5. Stage-specific quercetin sulfation in the gut of Mythimna separata larvae (Lepidoptera: Noctuidae).

    PubMed

    Aboshi, Takako; Ishida, Masahiro; Matsushita, Kaori; Hirano, Yunosuke; Nishida, Ritsuo; Mori, Naoki

    2014-01-01

    The metabolism of quercetin was investigated in Mythimna separata larvae. Quercetin 4'-O-sulfate was mainly identified in the frass when 6th instar larvae were fed artificial diets containing 1% quercetin. In the case of the 3rd instar larvae, a larger amount of quercetin was detected in the frass. M. separata larvae had different metabolic strategies for quercetin at different developmental stages. PMID:25036481

  6. Results of treatment of patients with second- to third-stage breast cancer by combination of low-level laser therapy (LLLT) and surgery: ten-year experience

    NASA Astrophysics Data System (ADS)

    Mikhailov, V. A.; Denisov, I. N.; Frank, George A.; Voltchenko, N. N.

    2000-06-01

    Laser therapy with semiconductor laser was performed on 41 patients with 2nd-3rd stage breast cancer. LLLT was used before surgery and in postoperative during 2 years. LLLT decreased postoperative complications by 15.3 percent and decreased duration of limphorrhea. 86.9 percent of patients with 2nd stage breast cancer survived 10 years after LLLT treatment. For patients with III stage breast cancer treated by LLLT the rate was 83.3 percent. 82.6 percent of patients with 2nd stage treated by LLLT had no recurrences in 10 years period. 77.7 percent of patients with 3RD stage treated by LLLT had no recurrences for the same period of time.

  7. Stage Posts

    ERIC Educational Resources Information Center

    Soulsby, Jim

    2004-01-01

    Uncertainty about identity and the future is occurring at a stage of life when people do question what they have achieved and what they still want to achieve. The notion of midlife crisis has been in existence for some time but recently its occurrence has coincided with opportunities to take early retirement or redundancy. This has meant that the…

  8. Assessing change in diet and biological affinity between the 4th and 3rd millennia cal BCE in the Portuguese Estremadura: a preliminary dental comparison of Feteira II and Bolores.

    PubMed

    Horwath, B C; Waterman, A J; Lillios, K T; Irish, J D

    2014-04-01

    Although the social and political changes accompanying the transition from the Neolithic through Copper Age, between the 4th and 3rd millennia cal BCE, in southwestern Iberia are reasonably well understood, much less is known about whether population movements and dietary changes accompanied these transformations. To address this question, human dental remains from the Middle through Late Neolithic site of Feteira II (3600-2900 cal BCE) and the Late Neolithic site of Bolores (2800-2600 cal BCE) in the Portuguese Estremadura were used to examine diet (microwear) and affinity (dental non-metrics). Microwear features were not found to be significantly different between Feteira II and Bolores, suggesting that the emergence of social complexity during this period did not result in large-scale changes in subsistence practices during the period of use at these sites. Using the Arizona State University Dental Anthropology System and supporting statistics, no significant difference between the samples from Feteira II and Bolores was observed, suggesting that no population replacement occurred between the Middle Neolithic and Late Neolithic/Copper Age. However, at Bolores there is some indication that there may have been demographic exchanges between southern Iberian and North African populations during the Late Neolithic/Copper Age. PMID:24642202

  9. Costs, affordability, and feasibility of an essential package of cancer control interventions in low-income and middle-income countries: key messages from Disease Control Priorities, 3rd edition.

    PubMed

    Gelband, Hellen; Sankaranarayanan, Rengaswamy; Gauvreau, Cindy L; Horton, Susan; Anderson, Benjamin O; Bray, Freddie; Cleary, James; Dare, Anna J; Denny, Lynette; Gospodarowicz, Mary K; Gupta, Sumit; Howard, Scott C; Jaffray, David A; Knaul, Felicia; Levin, Carol; Rabeneck, Linda; Rajaraman, Preetha; Sullivan, Terrence; Trimble, Edward L; Jha, Prabhat

    2016-05-21

    Investments in cancer control--prevention, detection, diagnosis, surgery, other treatment, and palliative care--are increasingly needed in low-income and particularly in middle-income countries, where most of the world's cancer deaths occur without treatment or palliation. To help countries expand locally appropriate services, Cancer (the third volume of nine in Disease Control Priorities, 3rd edition) developed an essential package of potentially cost-effective measures for countries to consider and adapt. Interventions included in the package are: prevention of tobacco-related cancer and virus-related liver and cervical cancers; diagnosis and treatment of early breast cancer, cervical cancer, and selected childhood cancers; and widespread availability of palliative care, including opioids. These interventions would cost an additional US$20 billion per year worldwide, constituting 3% of total public spending on health in low-income and middle-income countries. With implementation of an appropriately tailored package, most countries could substantially reduce suffering and premature death from cancer before 2030, with even greater improvements in later decades. PMID:26578033

  10. Current practice of epidemiology in Africa: highlights of the 3rd conference of the African epidemiological association and 1st conference of the Cameroon society of epidemiology, Yaoundé, Cameroon, 2014

    PubMed Central

    Nkwescheu, Armand Seraphin; Fokam, Joseph; Tchendjou, Patrice; Nji, Akindeh; Ngouakam, Hermann; Andre, Bita Fouda; Joelle, Sobngwi; Uzochukwu, Benjamin; Akinroye, Kingsley; Mbacham, Wilfred; Colizzi, Vittorio; Leke, Rose; Victora, Cesar

    2015-01-01

    As the study of disease occurrence and health indicators in human populations, Epidemiology is a dynamic field that evolves with time and geographical context. In order to update African health workers on current epidemiological practices and to draw awareness of early career epidemiologists on concepts and opportunities in the field, the 3rd African Epidemiology Association and the 1st Cameroon Society of Epidemiology Conference was organized in June 2-6, 2014 at the Yaoundé Mont Febe Hotel, in Cameroon. Under the theme«Practice of Epidemiology in Africa: Stakes, Challenges and Perspectives», the conference attracted close to five hundred guest and participants from all continents. The two main programs were the pre-conference course for capacity building of African Early Career epidemiologists, and the conference itself, providing a forum for scientific exchanges on recent epidemiological concepts, encouraging the use of epidemiological methods in studying large disease burden and neglected tropical diseases; and highlighting existing opportunities. PMID:26523191

  11. Report on the 3'rd scientific meeting of the "Verein zur Förderung des Wissenschaftlichen Nachwuchses in der Neurologie" (NEUROWIND e.V.) held in Motzen, Germany, Nov. 4'th - Nov. 6'th, 2011

    PubMed Central

    2012-01-01

    From November 4th- 6th 2011, the 3rd NEUROWIND e.V. meeting was held in Motzen, Brandenburg, Germany. Like in the previous years, the meeting provided an excellent platform for scientific exchange and the presentation of innovative projects for young colleagues in the fields of neurovascular research, neuroinflammation and neurodegeneration. As kick-off to the scientific sessions, Reinhard Hohlfeld, Head of the Institute for Clinical Neuroimmunology in Munich, gave an illustrious overview on the many fascinations of neuroimmunologic research. A particular highlight on the second day of the meeting was the award of the 1'st NEUROWIND e.V. prize for young academics in the field of experimental neurology. This award is posted for young colleagues under the age of 35 with a significant achievement in the field of neurovascular research, neuroinflammation or neurodegeneration and comprises an amount of 20.000 Euro, founded by Merck Serono GmbH, Darmstadt. Germany. The first prize was awarded to Ivana Nikic from Martin Kerschensteiner's group in Munich for her brilliant work on a reversible form of axon damage in experimental autoimmune encephalomyelitis and multiple sclerosis, published in Nature Medicine in 2011. This first prize award ceremony was a great incentive for the next call for proposals now upcoming in 2012. PMID:22360825

  12. Stages of Anal Cancer

    MedlinePlus

    ... following stages are used for anal cancer: Stage 0 (Carcinoma in Situ) In stage 0 , abnormal cells ... or check-ups. Treatment Options by Stage Stage 0 (Carcinoma in Situ) Treatment of stage 0 is ...

  13. Activation of the IGF1R pathway potentially mediates acquired resistance to mutant-selective 3rd-generation EGF receptor tyrosine kinase inhibitors in advanced non-small cell lung cancer.

    PubMed

    Park, Ji Hyun; Choi, Yun Jung; Kim, Seon Ye; Lee, Jung-Eun; Sung, Ki Jung; Park, Sojung; Kim, Woo Sung; Song, Joon Seon; Choi, Chang-Min; Sung, Young Hoon; Rho, Jin Kyung; Lee, Jae Cheol

    2016-04-19

    Mutant-selective, 3rd-generation EGFR-TKIs were recently developed to control lung cancer cells harboring T790M-mediated resistance. However, the development of resistance to these novel drugs seems inevitable. Thus, we investigated the mechanism of acquired resistance to the mutant-selective EGFR-TKI WZ4002. We established five WZ4002-resistant cells, derived from cells harboring both EGFR and T790M mutations by long-term exposure to increasing doses of WZ4002. Compared with the parental cells, all resistant cells showed 10-100-folds higher resistance to WZ4002, as well as cross-resistance to other mutant-selective inhibitors. Among them, three resistant cells (HCC827/WR, PC-9/WR and H1975/WR) showed dependency on EGFR signaling, but two other cells (PC-9/GR/WR and PC-9/ER/WR) were not. Notably, insulin-like growth factor-1 receptor (IGF1R) was aberrantly activated in PC-9/GR/WR cells in phospho-receptor tyrosine kinase array, consistently accompanied by loss of IGF binding protein-3 (IGFBP3). Down-regulation of IGF1R by shRNA, as well as inhibition of IGF1R activity either by AG-1024 (a small molecule IGF1R inhibitor) or BI 836845 (a monoclonal anti-IGF1/2 blocking antibody), restored the sensitivity to WZ4002 both in vitro and xenograft. Taken together, these results suggest that activation of the IGF1R pathway associated with IGFBP3 loss can induce an acquired resistance to the mutant-selective EGFR-TKI, WZ4002. Therefore, a combined therapy of IGF1R inhibitors and mutant-selective EGFR-TKIs might be a viable treatment strategy for overcoming acquired resistance. PMID:26980747

  14. Activation of the IGF1R pathway potentially mediates acquired resistance to mutant-selective 3rd-generation EGF receptor tyrosine kinase inhibitors in advanced non-small cell lung cancer

    PubMed Central

    Park, Ji Hyun; Choi, Yun Jung; Kim, Seon Ye; Lee, Jung-Eun; Sung, Ki Jung; Park, Sojung; Kim, Woo Sung; Song, Joon Seon; Choi, Chang-Min; Sung, Young Hoon; Rho, Jin Kyung; Lee, Jae Cheol

    2016-01-01

    Mutant-selective, 3rd-generation EGFR-TKIs were recently developed to control lung cancer cells harboring T790M-mediated resistance. However, the development of resistance to these novel drugs seems inevitable. Thus, we investigated the mechanism of acquired resistance to the mutant-selective EGFR-TKI WZ4002. We established five WZ4002-resistant cells, derived from cells harboring both EGFR and T790M mutations by long-term exposure to increasing doses of WZ4002. Compared with the parental cells, all resistant cells showed 10–100-folds higher resistance to WZ4002, as well as cross-resistance to other mutant-selective inhibitors. Among them, three resistant cells (HCC827/WR, PC-9/WR and H1975/WR) showed dependency on EGFR signaling, but two other cells (PC-9/GR/WR and PC-9/ER/WR) were not. Notably, insulin-like growth factor-1 receptor (IGF1R) was aberrantly activated in PC-9/GR/WR cells in phospho-receptor tyrosine kinase array, consistently accompanied by loss of IGF binding protein-3 (IGFBP3). Down-regulation of IGF1R by shRNA, as well as inhibition of IGF1R activity either by AG-1024 (a small molecule IGF1R inhibitor) or BI 836845 (a monoclonal anti-IGF1/2 blocking antibody), restored the sensitivity to WZ4002 both in vitro and xenograft. Taken together, these results suggest that activation of the IGF1R pathway associated with IGFBP3 loss can induce an acquired resistance to the mutant-selective EGFR-TKI, WZ4002. Therefore, a combined therapy of IGF1R inhibitors and mutant-selective EGFR-TKIs might be a viable treatment strategy for overcoming acquired resistance. PMID:26980747

  15. Evaluation of the effect of a 3rd GnRH injection administered six days after the 2nd GnRH injection of Ovsynch on the reproductive performance of Japanese black cows

    PubMed Central

    Gaja, Abdurraouf Omar; Hamana, Katsumi; Kojima, Toshiyuki

    2008-01-01

    This study was designed to evaluate the reproductive performance of Japanese black cows following the 3rd injection of gonadotropin releasing hormone (GnRH) analogue administered concurrently with Ovsynch-based treatment on day 6 (day 1 = the day of ovulation). In Experiment 1, 12 cows were allocated into three groups: a control group that was subjected to Ovsynch treatment and then injected with a placebo on day 6; group 1 (Ovsynch + GnRH), which was subjected to Ovsynch treatment and was injected with GnRH analogue on day 6, and group 2 (Ovsynch + controlled internal drug-release (CIDR) + GnRH), which received Ovsynch-CIDR treatment and was injected with GnRH analogue on day 6. Blood collection and ultrasonographic observation of the ovaries were conducted daily. Both treatments induced the formation of an accessory corpus luteum and significantly increased the cross-sectional area of the luteal tissue when compared to the control. However, plasma progesterone (P4) was significantly higher in the treatment groups than in the control group on days 11, 12, 17 and 18 in the group 1 and from day 10 to 21 in the group 2. In Experiment 2, 41 cows were assigned to the same three groups described above and then artificially inseminated on day 1. The pregnancy rates on day 45 did not differ among groups. In conclusion, administration of GnRH analogue on day 6 following Ovsynch-based treatment did not improve the reproductive performance of Japanese black cows, even though the P4 concentration was higher in groups that received the GnRH. PMID:18716447

  16. Structural development of human brain white matter from mid-fetal to perinatal stage

    NASA Astrophysics Data System (ADS)

    Ouyang, Austin; Yu, Qiaowen; Mishra, Virendra; Chalak, Lina; Jeon, Tina; Sivarajan, Muraleedharan; Jackson, Greg; Rollins, Nancy; Liu, Shuwei; Huang, Hao

    2015-03-01

    The structures of developing human brain white matter (WM) tracts can be effectively quantified by DTI-derived metrics, including fractional anisotropy (FA), mean, axial and radial diffusivity (MD, AD and RD). However, dynamics of WM microstructure during very early developmental period from mid-fetal to perinatal stage is unknown. It is difficult to accurately measure microstructural properties of these WM tracts due to severe contamination from cerebrospinal fluid (CSF). In this study, high resolution DTI of fetal brains at mid-fetal stage (20 weeks of gestation or 20wg), 19 brains in the middle of 3rd trimester (35wg) and 17 brains around term (40wg) were acquired. We established first population-averaged DTI templates at these three time points and extracted WM skeleton. 16 major WM tracts in limbic, projection, commissural and association tract groups were traced with DTI tractography in native space. The WM skeleton in the template space was inversely transformed back to the native space for measuring core WM microstructures of each individual tract. Continuous microstructural enhancement and volumetric increase of WM tracts were found from 20wg to 40wg. The microstructural enhancement from FA measurement is decelerated in late 3rd trimester compared to mid-fetal to middle 3rd trimester, while volumetric increase of prefrontal WM tracts is accelerated. The microstructural enhancement from 35wg to 40wg is heterogeneous among different tract groups with microstructures of association tracts undergoing most dramatic change. Besides decreases of RD indicating active myelination, the decrease of AD for most WM tracts during late 3rd trimester suggests axonal packing process.

  17. Stages and Behaviors

    MedlinePlus

    ... Stage Caregiving Middle-Stage Caregiving Late-Stage Caregiving Behaviors Aggression & Anger Anxiety & Agitation Depression Hallucinations Memory Loss & ... Legal Documents alz.org » Caregiver Center » Stages and Behaviors Text size: A A A Stages / Behaviors As ...

  18. Comparative analysis of flower volatiles from nine citrus at three blooming stages.

    PubMed

    Azam, Muhammad; Song, Min; Fan, Fangjuan; Zhang, Bo; Xu, Yaying; Xu, Changjie; Chen, Kunsong

    2013-01-01

    Volatiles from flowers at three blooming stages of nine citrus cultivars were analyzed by headspace-solid phase microextraction (HS-SPME)-GC-MS. Up to 110 volatiles were detected, with 42 tentatively identified from citrus flowers for the first time. Highest amounts of volatiles were present in fully opened flowers of most citrus, except for pomelos. All cultivars were characterized by a high percentage of either oxygenated monoterpenes or monoterpene hydrocarbons, and the presence of a high percentage of nitrogen containing compounds was also observed. Flower volatiles varied qualitatively and quantitatively among citrus types during blooming. Limonene was the most abundant flower volatile only in citrons; α-citral and β-citral ranked 2nd and 3rd only for Bergamot, and unopened flowers of Ponkan had a higher amount of linalool and β-pinene while much lower amount of γ-terpinene and p-cymene than Satsuma. Taking the average of all cultivars, linalool and limonene were the top two volatiles for all blooming stages; β-pinene ranked 3rd in unopened flowers, while indole ranked 3rd for half opened and fully opened flower volatiles. As flowers bloomed, methyl anthranilate increased while 2-hexenal and p-cymene decreased. In some cases, a volatile could be high in both unopened and fully opened flowers but low in half opened ones. Through multivariate analysis, the nine citrus cultivars were clustered into three groups, consistent with the three true citrus types. Furthermore, an influence of blooming stages on clustering was observed, especially with hybrids Satsuma and Huyou. Altogether, it was suggested that flower volatiles can be suitable markers for revealing the genetic relationships between citrus cultivars but the same blooming stage needs to be strictly controlled. PMID:24232454

  19. Comparative Analysis of Flower Volatiles from Nine Citrus at Three Blooming Stages

    PubMed Central

    Azam, Muhammad; Song, Min; Fan, Fangjuan; Zhang, Bo; Xu, Yaying; Xu, Changjie; Chen, Kunsong

    2013-01-01

    Volatiles from flowers at three blooming stages of nine citrus cultivars were analyzed by headspace-solid phase microextraction (HS-SPME)-GC-MS. Up to 110 volatiles were detected, with 42 tentatively identified from citrus flowers for the first time. Highest amounts of volatiles were present in fully opened flowers of most citrus, except for pomelos. All cultivars were characterized by a high percentage of either oxygenated monoterpenes or monoterpene hydrocarbons, and the presence of a high percentage of nitrogen containing compounds was also observed. Flower volatiles varied qualitatively and quantitatively among citrus types during blooming. Limonene was the most abundant flower volatile only in citrons; α-citral and β-citral ranked 2nd and 3rd only for Bergamot, and unopened flowers of Ponkan had a higher amount of linalool and β-pinene while much lower amount of γ-terpinene and p-cymene than Satsuma. Taking the average of all cultivars, linalool and limonene were the top two volatiles for all blooming stages; β-pinene ranked 3rd in unopened flowers, while indole ranked 3rd for half opened and fully opened flower volatiles. As flowers bloomed, methyl anthranilate increased while 2-hexenal and p-cymene decreased. In some cases, a volatile could be high in both unopened and fully opened flowers but low in half opened ones. Through multivariate analysis, the nine citrus cultivars were clustered into three groups, consistent with the three true citrus types. Furthermore, an influence of blooming stages on clustering was observed, especially with hybrids Satsuma and Huyou. Altogether, it was suggested that flower volatiles can be suitable markers for revealing the genetic relationships between citrus cultivars but the same blooming stage needs to be strictly controlled. PMID:24232454

  20. Second Stage Separation

    NASA Video Gallery

    When the second stage burn is complete, the spacecraft and third stage are spun up to 55 rpm to stabilize the third stage during its short firing. The second stage is then jettisoned and the third ...

  1. Detection of Gnathostoma spinigerum Third-Stage Larvae in Snakeheads Purchased from a Central Part of Myanmar

    PubMed Central

    Jung, Bong-Kwang; Lee, Jin-Ju; Pyo, Kyoung-Ho; Kim, Hyeong-Jin; Jeong, Hoo-Gn; Yoon, Cheong-Ha; Lee, Soon-Hyung; Shin, Eun-Hee

    2008-01-01

    To examine the infection status of freshwater fish with Gnathostoma spp. larvae in Myanmar, we purchased 15 snakeheads, Channa striatus, from a local market in a suburban area of Naypyidaw, the new capital city. Two larval gnathostomes were collected using an artificial digestion technique, and observed by a light microscope and a scanning electron microscope. The size of an intact larva was 2.65 mm long and 0.32 mm wide. The characteristic morphology of the larvae included the presence of a long esophagus (0.80 mm long), 2 pairs of cervical sacs (0.43 mm long), and a characteristic head bulb with 4 rows of hooklets. The number of hooklets in the 1st, 2nd, 3rd, and 4th row was 45, 48, 50, and 52, respectively. Based on these morphological characters, the larvae were identified as the advanced 3rd-stage larvae of Gnathostoma spinigerum. This is the first report of detection of G. spinigerum 3rd-stage larvae in the central part of Myanmar. Our study suggests that intake of raw meat of snakehead fish in Myanmar may result in human gnathostomiasis. PMID:19127338

  2. The insecticidal activity of Eucalyptus globulus oil on the development of Musca domestica third stage larvae.

    PubMed

    Abdel Halim, Azza S; Morsy, Tosson A

    2005-08-01

    The insecticidal activity of Eucalyptus globulus oil (Camphor oil) against the larval maturation and adult emergency of the house-fly, Musca domestica 3rd stage was evaluated under controlled laboratory conditions. Concentrations of 100%, 70%, 50% 25%, 5%, 2%, 1%, 0.9 % and 0.7% showed 100% larval mortality rate. At concentrations of 0.5%, 0.3%, 0.2% and 0.1% the larval mortality rate was 90%. On the other hand, the developed pupae did not emerge to adults. Eucalyptus globulus oil is safe, cheap and widely used in Medicine. So, it is recommended to be use in controlling larvae of M. domestica. PMID:16083072

  3. Pancreatic Cancer Stage 3

    MedlinePlus

    ... historical Searches are case-insensitive Pancreatic Cancer Stage 3 Add to My Pictures View /Download : Small: 720x576 ... Large: 3000x2400 View Download Title: Pancreatic Cancer Stage 3 Description: Stage III pancreatic cancer; drawing shows cancer ...

  4. Comparison of serum creatinine, cystatin C, and neutrophil gelatinase-associated lipocalin for acute kidney injury occurrence according to risk, injury, failure, loss, and end-stage criteria classification system in early after living kidney donation.

    PubMed

    Hekmat, Reza; Mohebi, Mahmood

    2016-01-01

    To evaluate the kidney function after living kidney donation, we measured serum creatinine (SCr), cystatin C, and neutrophil gelatinase-associated lipocalin (NGAL) of 42 living donors before uninephrectomy and in three immediate days after it. We also evaluated the prevalence of the occurrence of the different stages of acute kidney injury (AKI) classified according to risk, injury, failure, loss, and end-stage (RIFLE) criteria, and accuracy of each of these three biomarkers for predicting them were evaluated. Significant serum NGAL (s-NGAL) changes were limited to the 1 st day after donation, whereas SCr and cystatin C changes continued to the third day after donation. s-NGAL level in the 1 st day and serum cystatin C in the 3 rd day after donation, respectively, had the largest area under curve and best sensitivity and specificity for Stage 1 (risk) AKI prediction. During the immediate three days after donation, about half of patients suffered from AKI; mostly Stage 1 (injury). The sequence of the emergence of s-NGAL and s-cystatin C in the 1 st and 3 rd days as biomarkers with highest accuracy and power for RIFLE criteria defined AKI stage discrimination in our study was comparable to previous studies. We conclude that our study suggests that AKI was best detected in the 1 st day after uninephrectomy by the s-NGAL levels, whereas cystatin C was the best in the 3 rd day after donation for detection of AKI. PMID:27424680

  5. Cervical Cancer Stage IIIB

    MedlinePlus

    ... Cancer Stage IIIB Description: Stage IIIB cervical cancer; drawing shows cancer in the cervix, the vagina, and ... that connect the kidneys to the bladder). The drawing shows the ureter on the right blocked by ...

  6. Breast cancer staging

    MedlinePlus

    ... this page: //medlineplus.gov/ency/patientinstructions/000911.htm Breast cancer staging To use the sharing features on this ... Once your health care team knows you have breast cancer , they will do more tests to stage it. ...

  7. Cervical Cancer Stage IVB

    MedlinePlus

    ... of the body, such as the lymph nodes, lung, liver, intestine, or bone. Stage IVB cervical cancer. Topics/Categories: Anatomy -- Gynecologic Cancer Types -- Cervical Cancer Staging Type: Color, Medical Illustration Source: National Cancer Institute ...

  8. Lunar Module Ascent Stage

    NASA Technical Reports Server (NTRS)

    1969-01-01

    The Lunar Module 'Spider' ascent stage is photographed from the Command/Service Module on the fifth day of the Apollo 9 earth-orbital mission. The Lunar Module's descent stage had already been jettisoned.

  9. Stages of Adolescence

    MedlinePlus

    ... Español Text Size Email Print Share Stages of Adolescence Page Content Article Body Adolescence, these years from puberty to adulthood, may be roughly divided into three stages: early adolescence, generally ages eleven to fourteen; middle adolescence, ages ...

  10. Current systems: Upper stages

    NASA Technical Reports Server (NTRS)

    Gunn, Charles R.

    1991-01-01

    The United States orbital transfer vehicles are presented: PAM-D (Payload Assist Module); PAM-D2; IUS (Inertial Upper Stage); and TOS (Transfer Orbit Stage). This presentation is represented by viewgraphs.

  11. Beyond Erikson's Eight Stages.

    ERIC Educational Resources Information Center

    Whitney, Ruth

    1979-01-01

    Erik Erikson has described eight stages of the healthy personality. This essay offers a revised version of the eight stages. Although most individuals develop through the eight stages, each is personally unique because patterns of fluctuation between safety and growth differ from one individual to another. (Author)

  12. Cervical Cancer Stage IA

    MedlinePlus

    ... historical Searches are case-insensitive Cervical Cancer Stage IA Add to My Pictures View /Download : Small: 720x576 ... Large: 3000x2400 View Download Title: Cervical Cancer Stage IA Description: Stage IA1 and IA2 cervical cancer; drawing ...

  13. Ovarian Cancer Stage IV

    MedlinePlus

    ... hyphen, e.g. -historical Searches are case-insensitive Ovarian Cancer Stage IV Add to My Pictures View /Download : ... 1200x1335 View Download Large: 2400x2670 View Download Title: Ovarian Cancer Stage IV Description: Drawing of stage IV shows ...

  14. Ovarian Cancer Stage IIIC

    MedlinePlus

    ... hyphen, e.g. -historical Searches are case-insensitive Ovarian Cancer Stage IIIC Add to My Pictures View /Download : ... 1530x1350 View Download Large: 3060x2700 View Download Title: Ovarian Cancer Stage IIIC Description: Drawing of stage IIIC shows ...

  15. Ovarian Cancer Stage II

    MedlinePlus

    ... hyphen, e.g. -historical Searches are case-insensitive Ovarian Cancer Stage II Add to My Pictures View /Download : ... 1650x675 View Download Large: 3300x1350 View Download Title: Ovarian Cancer Stage II Description: Three-panel drawing of stage ...

  16. Ovarian Cancer Stage I

    MedlinePlus

    ... hyphen, e.g. -historical Searches are case-insensitive Ovarian Cancer Stage I Add to My Pictures View /Download : ... 1650x675 View Download Large: 3300x1350 View Download Title: Ovarian Cancer Stage I Description: Three-panel drawing of stage ...

  17. Cetuximab, Cisplatin, and Radiation Therapy in Treating Patients With Stage IB, Stage II, Stage III, or Stage IVA Cervical Cancer

    ClinicalTrials.gov

    2014-12-29

    Cervical Adenocarcinoma; Cervical Adenosquamous Carcinoma; Cervical Small Cell Carcinoma; Cervical Squamous Cell Carcinoma; Stage IB Cervical Cancer; Stage IIA Cervical Cancer; Stage IIB Cervical Cancer; Stage III Cervical Cancer; Stage IVA Cervical Cancer

  18. Two stage catalytic combustor

    NASA Technical Reports Server (NTRS)

    Alvin, Mary Anne (Inventor); Bachovchin, Dennis (Inventor); Smeltzer, Eugene E. (Inventor); Lippert, Thomas E. (Inventor); Bruck, Gerald J. (Inventor)

    2010-01-01

    A catalytic combustor (14) includes a first catalytic stage (30), a second catalytic stage (40), and an oxidation completion stage (49). The first catalytic stage receives an oxidizer (e.g., 20) and a fuel (26) and discharges a partially oxidized fuel/oxidizer mixture (36). The second catalytic stage receives the partially oxidized fuel/oxidizer mixture and further oxidizes the mixture. The second catalytic stage may include a passageway (47) for conducting a bypass portion (46) of the mixture past a catalyst (e.g., 41) disposed therein. The second catalytic stage may have an outlet temperature elevated sufficiently to complete oxidation of the mixture without using a separate ignition source. The oxidation completion stage is disposed downstream of the second catalytic stage and may recombine the bypass portion with a catalyst exposed portion (48) of the mixture and complete oxidation of the mixture. The second catalytic stage may also include a reticulated foam support (50), a honeycomb support, a tube support or a plate support.

  19. Staged electrostatic precipitator

    DOEpatents

    Miller, Stanley J.; Almlie, Jay C.; Zhuang, Ye

    2016-03-01

    A device includes a chamber having an air inlet and an air outlet. The device includes a plurality of stages including at least a first stage adjacent a second stage. The plurality of stages are disposed in the chamber and each stage has a plurality of discharge electrodes disposed in an interior region and is bounded by an upstream baffle on an end proximate the air inlet and bounded by a downstream baffle on an end proximate the air outlet. Each stage has at least one sidewall between the upstream baffle and the downstream baffle. The sidewall is configured as a collection electrode and has a plurality of apertures disposed along a length between the upstream baffle and the downstream baffle. The upstream baffle of the first stage is positioned in staggered alignment relative to the upstream baffle of the second stage and the downstream baffle of the first stage are positioned in staggered alignment relative to the downstream baffle of the second stage.

  20. Staging of hepatocellular carcinoma.

    PubMed

    Duseja, Ajay

    2014-08-01

    Hepatocellular carcinoma (HCC) is different from other malignancies because the prognosis in HCC is not only dependent upon the tumor stage but also on the liver function impairment due to accompanying cirrhosis liver. Various other staging systems used in HCC include the European systems [French staging system, Barcelona Clinic Liver Cancer (BCLC) staging system and the cancer of the liver Italian program (CLIP)] and Asian systems [Okuda staging system, Japan integrated Staging (JIS), Tokyo score and Chinese University Prognostic Index (CUPI)]. Out of all the staging systems used in HCC, Barcelona Clinic Liver Cancer (BCLC) staging system is probably the best because it takes in to account the tumor status (defined by tumor size and number, presence of vascular invasion and extrahepatic spread), liver function (defined either by the Child-Pugh's class) and general health status of the patient (defined by the ECOG classification and the presence of symptoms). Since most of the extrahepatic spread in HCC occurs to lymph nodes, lungs and bones, the assessment can be done with either PET/CT or a combination of CT (Chest and abdomen) and a bone scan. This article describes the various staging systems used in HCC, guides choosing a staging system particularly in the Indian context and the assessment of extra-hepatic spread in HCC. PMID:25755615

  1. Multiple stage railgun

    SciTech Connect

    Aaland, K.; Hawke, R.S.; Scudder, J.K.

    1982-08-10

    A multiple stage magnetic railgun accelerator for accelerating a projectile by movement of a plasma arc along the rails. The railgun is divided into a plurality of successive rail stages which are sequentially energized by separate energy sources as the projectile moves through the bore of the railgun. Propagation of energy from an energized rail stage back towards the breech end of the railgun can be prevented by connection of the energy sources to the rails through isolation diodes. Propagation of energy from an energized rail stage back towards the breech end of the railgun can also be prevented by dividing the rails into electrically isolated rail sections. In such case means are used to extinguish the arc at the end of each energized stage and a fuse or laser device is used to initiate a new plasma arc in the next energized rail stage.

  2. Two-stage Supercharging

    NASA Technical Reports Server (NTRS)

    Buck, Richard S

    1941-01-01

    The arrangement of the parts and the installation and control problems of the two-stage mechanically driven superchargers for aircraft engines are discussed. Unless an entirely new form of supercharging is developed, there will be a definite need for a two-stage centrifugal supercharger. It is shown that the two-stage mechanically driven supercharger itself is a comparatively simple device; the complications arise from the addition of inter-coolers and controls.

  3. Design and predicted performance of the 3-stage ADR for the Soft-X-ray Spectrometer instrument on Astro-H

    NASA Astrophysics Data System (ADS)

    Shirron, Peter J.; Kimball, Mark O.; James, Bryan L.; Wegel, Donald C.; Martinez, Raul M.; Faulkner, Richard L.; Neubauer, Larry; Sansebastian, Marcelino

    2012-04-01

    The Japanese Astro-H mission will include the Soft X-ray Spectrometer (SXS) instrument provided by NASA/GSFC. The SXS will perform imaging spectroscopy in the soft X-ray band using a 6 × 6 array of silicon microcalorimeters operated at 50 mK. The detectors will be cooled by a 3-stage adiabatic demagnetization refrigerator (ADR). The configuration allows the ADR to operate with both a 1.3 K superfluid helium bath and a 4.5 K cryocooler as its heat sink. Initially, when liquid helium is present, the two coldest stages of the ADR will operate in a single-shot mode to cool the detectors from 1.3 K. During this phase of the mission, the 3rd stage may be used to reduce the net heat load on the liquid helium and extend its lifetime. When the liquid is depleted, the 2nd and 3rd stages will operate in a continuous mode to maintain the helium tank at about 1.3 K, allowing continued operation of the 1st stage (in a single-shot mode) and hence the SXS instrument. This paper describes the design and operating modes of the ADR, as well as details of critical components.

  4. MK2206 in Treating Patients With Stage I, Stage II, or Stage III Breast Cancer

    ClinicalTrials.gov

    2015-03-16

    Estrogen Receptor Negative; Estrogen Receptor Positive; HER2/Neu Negative; HER2/Neu Positive; Progesterone Receptor Negative; Progesterone Receptor Positive; Stage IA Breast Cancer; Stage IB Breast Cancer; Stage IIA Breast Cancer; Stage IIB Breast Cancer; Stage IIIA Breast Cancer; Stage IIIB Breast Cancer; Stage IIIC Breast Cancer; Triple-Negative Breast Carcinoma

  5. "High Stage" Organizing.

    ERIC Educational Resources Information Center

    Torbert, William R.

    Although a psychological theory of stages of transformation in human development currently exists, organizational researchers have yet to elaborate and test any theory of organizational transformation of comparable elegance. According to the organizational stage theory being developed since 1974 by William Torbert, bureaucratic organization, which…

  6. The 1991 3rd NASA Symposium on VLSI Design

    NASA Technical Reports Server (NTRS)

    Maki, Gary K.

    1991-01-01

    Papers from the symposium are presented from the following sessions: (1) featured presentations 1; (2) very large scale integration (VLSI) circuit design; (3) VLSI architecture 1; (4) featured presentations 2; (5) neural networks; (6) VLSI architectures 2; (7) featured presentations 3; (8) verification 1; (9) analog design; (10) verification 2; (11) design innovations 1; (12) asynchronous design; and (13) design innovations 2.

  7. The radiology of joint disease. 3rd Ed

    SciTech Connect

    Forrester, D.M.; Brown, J.C.

    1987-01-01

    The book is a systematic radiographic approach to the arthritides. Part one deals with hand abnormalities ''to facilitate the teaching of basic principles and to dramatize the differences between radiographic features of various arthritides,'' as stated in the forward of the first edition. Part two, ''Arthritis from Head to Foot,'' illustrates the same diseases as they affect other joints. The ABCs (alignment, bone mineralization, cartilage space, soft tissue) approach is followed throughout the book. For example, reflex sympathetic dystrophy syndrome is dealt with in six different locations, and metatarsal stress fractures are mentioned in a chapter on erosions in rheumatoid arthritis.

  8. Mathematics in Early Years Education. 3rd Edition

    ERIC Educational Resources Information Center

    Montague-Smith, Ann; Price, Alison

    2012-01-01

    This third edition of the best-selling "Mathematics in Nursery Education" provides an accessible introduction to the teaching of mathematics in the early years. Covering all areas of mathematics learning--number and counting, calculation, pattern, shape, measures and data handling--it summarises the research findings and underlying key concepts…

  9. The Philosophic Process in Physical Education. 3rd Edition.

    ERIC Educational Resources Information Center

    Harper, William A.; And Others

    This book on the process of philosophic thought as it relates to physical education is divided into four parts. The first part, "Philosophy as Action," aims to help the student to develop and refine his ability to philosophize, to direct reasoned beliefs toward a goal, to see that reasoned beliefs derive from thinking, to avoid error and dangers…

  10. Intelec 81, International Telecommunications Energy Conference, 3rd, 1981

    SciTech Connect

    Anon

    1981-01-01

    This conference proceedings contains 60 papers. Thirteen papers are indexed separately. Topics covered include: microprocessors for telecommunications power; distribution and economics; energy conservation and building environment; batteries; inverters; solar and wind power systems; uninterruptable power supplies; DC:DC converters; AC standby systems; reliability; and, DC power plant and rectifiers.

  11. Explanatory Supplement to the Astronomical Almanac (3rd Edition)

    NASA Astrophysics Data System (ADS)

    Urban, Sean E.; Seidelmann, P. K.

    2014-01-01

    Publications and software from the the Astronomical Applications Department of the US Naval Observatory (USNO) are used throughout the world, not only in the Department of Defense for safe navigation, but by many people including other navigators, astronomers, aerospace engineers, and geodesists. Products such as The Nautical Almanac, The Astronomical Almanac, and the Multiyear Interactive Computer Almanac (MICA) are regarded as international standards. To maintain credibility, it is imperative that the methodologies employed and the data used are well documented. "The Explanatory Supplement to the Astronomical Almanac" (hereafter, "The ES") is a major source of such documentation. It is a comprehensive reference book on positional astronomy, covering the theories and algorithms used to produce The Astronomical Almanac, an annual publication produced jointly by the Nautical Almanac Office of USNO and Her Majesty's Nautical Almanac Office (HMNAO). The first edition of The ES appeared in 1961, and the second followed in 1992. Several major changes have taken place in fundamental astronomy since the second edition was published. Advances in radio observations allowed the celestial reference frame to be tied to extragalactic radio sources, thus the International Celestial Reference System replaced the FK5 system. The success of ESA's Hipparcos satellite dramatically altered observational astrometry. Improvements in Earth orientation observations lead to new precession and nutation theories. Additionally, a new positional paradigm, no longer tied to the ecliptic and equinox, was accepted. Largely because of these changes, staff at USNO and HMNAO decided the time was right for the next edition of The ES. The third edition is now available; it is a complete revision of the 1992 book. Along with subjects covered in the previous two editions, the book also contains descriptions of the major advancements in positional astronomy over the last 20 years, some of which are described above. Extensive references to online information are given. This paper will discuss this latest edition of the Explanatory Supplement.

  12. Donations Increase for 3rd Year in a Row

    ERIC Educational Resources Information Center

    Strout, Erin

    2007-01-01

    This article talks about a report on fund-raising campaign done by universities and colleges to support their educational programs. According to the "Voluntary Support of Education" annual report released by the Council for Aid to Education, alumni and other individual donors gave just more than half of the total amount raised. The country's…

  13. [3rd Hungarian Breast Cancer Consensus Conference - Surgery Guidelines].

    PubMed

    Lázár, György; Bursics, Attila; Farsang, Zoltán; Harsányi, László; Kósa, Csaba; Maráz, Róbert; Mátrai, Zoltán; Paszt, Attila; Pavlovics, Gábor; Tamás, Róbert

    2016-09-01

    Therapy for breast cancer today is characterised by ever more precise diagnostic methods and ever more effective oncological treatments, a trend which will certainly continue in the future. Breast preservation and the application of oncoplastic principles are increasingly popular. A sentinel lymph node biopsy in the surgical treatment of the axilla is primary, with the indication for axillary block dissection (ABD) narrowing and radiation therapy becoming an alternative to ABD in certain cases. This publication summarises our recommendations on the surgical treatment of breast cancer based on the content of the 2nd Breast Cancer Consensus Conference and considering the latest international studies and professional recommendations. PMID:27579720

  14. International directory of electric utilities, 3rd Edition

    SciTech Connect

    Not Available

    1991-01-01

    The book covers 162 countries in Europe, Asia, Africa, Middle East, and Latin America. It contains hundreds of names of key utility executives, utility addresses, plus telephone, fax, and telex numbers. Power plant construction plants, new T D facilities and lines, names of major plants plus their locations, capacity, fuels, type of generation, etc. are included. It also includes listing of international engineering consultants and key executives, translations of key technical terms, and maps showing key facilities for all countries.

  15. Iowa Family Day Care Handbook. 3rd Edition.

    ERIC Educational Resources Information Center

    Holt, Bess Gene; Karas, Shirley C.

    The purposes of this handbook are (1) to help individuals who are thinking about becoming family day care providers decide whether the profession is appropriate for themselves and their families, and (2) to present ideas for setting up and maintaining a family day care home that provides high quality service to families, a developmental learning…

  16. Textbook of Child and Adolescent Psychiatry. 3rd Edition.

    ERIC Educational Resources Information Center

    Wiener, Jerry M.; Dulcan, Mina K.

    The third edition of this textbook continues its tradition of integrating clinical wisdom and scientific research to improve patient care and advocacy for children and families. Each of the 56 chapters presents a summary of a core topic, blending clinical experience with evidence-based practices in assessment and treatment. Divided into 10 parts,…

  17. The Development of TAFE in Australia. 3rd Edition.

    ERIC Educational Resources Information Center

    Goozee, Gillian

    This document traces the development of Australia's technical and further education (TAFE) system, which offers a wide range of courses providing education and training for employment at the operative, trade, and paraprofessional levels, as well as general education and literacy programs. The following are among the topics discussed: (1) general…

  18. EMSL Quarterly Highlights Report: FY 2008, 3rd Quarter

    SciTech Connect

    Showalter, Mary Ann

    2008-09-16

    The EMSL Quarterly Highlights Report covers the science, staff and user recognition, and publication activities that occurred during the 1st quarter (October 2007 - December 2007) of Fiscal Year 2008.

  19. Structures for the 3rd Generation Reusable Concept Vehicle

    NASA Technical Reports Server (NTRS)

    Hrinda, Glenn A.

    2001-01-01

    A major goal of NASA is to create an advance space transportation system that provides a safe, affordable highway through the air and into space. The long-term plans are to reduce the risk of crew loss to 1 in 1,000,000 missions and reduce the cost of Low-Earth Orbit by a factor of 100 from today's costs. A third generation reusable concept vehicle (RCV) was developed to assess technologies required to meet NASA's space access goals. The vehicle will launch from Cape Kennedy carrying a 25,000 lb. payload to the International Space Station (ISS). The system is an air breathing launch vehicle (ABLV) hypersonic lifting body with rockets and uses triple point hydrogen and liquid oxygen propellant. The focus of this paper is on the structural concepts and analysis methods used in developing the third generation reusable launch vehicle (RLV). Member sizes, concepts and material selections will be discussed as well as analysis methods used in optimizing the structure. Analysis based on the HyperSizer structural sizing software will be discussed. Design trades required to optimize structural weight will be presented.

  20. Microstructure Modeling of 3rd Generation Disk Alloy

    NASA Technical Reports Server (NTRS)

    Jou, Herng-Jeng

    2008-01-01

    The objective of this initiative, funded by NASA's Aviation Safety Program, is to model, validate, and predict, with high fidelity, the microstructural evolution of third-generation high-refractory Ni-based disc superalloys during heat treating and service conditions. This initiative is a natural extension of the DARPA-AIM (Accelerated Insertion of Materials) initiative with GE/Pratt-Whitney and with other process simulation tools. Strong collaboration with the NASA Glenn Research Center (GRC) is a key component of this initiative and the focus of this program is on industrially relevant disk alloys and heat treatment processes identified by GRC. Employing QuesTek s Computational Materials Dynamics technology and PrecipiCalc precipitation simulator, physics-based models are being used to achieve high predictive accuracy and precision. Combining these models with experimental data and probabilistic analysis, "virtual alloy design" can be performed. The predicted microstructures can be optimized to promote desirable features and concurrently eliminate nondesirable phases that can limit the reliability and durability of the alloys. The well-calibrated and well-integrated software tools that are being applied under the proposed program will help gas turbine disk alloy manufacturers, processing facilities, and NASA, to efficiently and effectively improve the performance of current and future disk materials.

  1. Business planning for scientists and engineers [3rd edition

    SciTech Connect

    Servo, Jenny C.

    1999-09-01

    This combination text/workbook is intended for use by scientists or engineers actively engaged in developing a product or technology to commercial production. The 'how' of planning is a central theme with special emphasis on development of operational plans and strategic thinking.

  2. Rentz's Student Affairs Practice in Higher Education. 3rd Edition

    ERIC Educational Resources Information Center

    MacKinnon, Fiona J. D.

    2004-01-01

    Students in the field, as well as experienced practitioners and administrators, will herein find an up-to-date and in-depth study of the major student affairs functions of a comprehensive campus program. Within its covers, the graduate student will find chapters describing everything the person new to student affairs needs to know about the major…

  3. Performance Plan: Progress Report, 3rd Quarter Fiscal Year 2000.

    ERIC Educational Resources Information Center

    Department of Education, Washington, DC. Student Financial Assistance.

    The U.S. Department of Education Student Financial Assistance (SFA) outlines its three major objectives for fiscal year 2000 in its progress report. The objectives are: 1)customer satisfaction; 2) reduction in the overall cost of delivering student aid; and 3) employee satisfaction. Several new capabilities were added to the Direct Loan servicing…

  4. Proceedings of the 3rd Annual SCOLE Workshop

    NASA Technical Reports Server (NTRS)

    Taylor, Lawrence W., Jr. (Compiler)

    1987-01-01

    Topics addressed include: modeling and controlling the Spacecraft Control Laboratory Experiment (SCOLE) configurations; slewing maneuvers; mathematical models; vibration damping; gravitational effects; structural dynamics; finite element method; distributed parameter system; on-line pulse control; stability augmentation; and stochastic processes.

  5. Growth and mineral nutrition of field crops 3rd Edition

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Green revolution technology of last century led to increased production. The green revolution, however, did not link farming system sustainability to food system sustainability as a whole. In recent years the rate of food-grain production has been lower than the rate of population growth. This will ...

  6. 3rd Miami international conference on alternative energy sources

    SciTech Connect

    Nejat Veziroglu, T.

    1980-01-01

    The conference includes sessions on solar energy, ocean thermal energy, wind energy, hydro power, nuclear breeders and nuclear fusion, synthetic fuels from coal or wastes, hydrogen production and uses, formulation of workable policies on energy use and energy conservation, heat and energy storage, and energy education. The volume of the proceedings presents the papers and lectures in condensed format grouped by subject under forty-two sessions for 319 presentations.

  7. Ectopic 3rd Molar Tooth in the Maxillary Antrum

    PubMed Central

    Bello, Seidu A.; Oketade, Ifeoluwa O.; Osunde, Otasowie D.

    2014-01-01

    Location of ectopic tooth in a nondentate area like the maxillary antrum is rare. A 17-year-old boy, with one year history of recurrent right facial swelling and radiographic finding of a maxillary third molar tooth located at the posterior wall of the maxillary antrum, is presented. Under endotracheal intubation, the tooth was extracted through a Caldwell-Luc antrostomy approach and patient had an uneventful recovery and has been symptom free for eight months. Ectopic tooth in the maxillary antrum is rare and is commonest with maxillary third molar. It may be symptomless but is more commonly associated with inflammatory symptoms. The treatment of choice is surgical excision which is mostly carried out with Caldwell-Luc approach, even though endoscopic approach is being reported. PMID:25132999

  8. Thermal radiation heat transfer (3rd revised and enlarged edition)

    NASA Astrophysics Data System (ADS)

    Siegel, Robert; Howell, John R.

    This book first reviews the overall aspects and background information related to thermal radiation heat transfer and incorporates new general information, advances in analytical and computational techniques, and new reference material. Coverage focuses on radiation from opaque surfaces, radiation interchange between various types of surfaces enclosing a vacuum or transparent medium, and radiation including the effects of partially transmitting media, such as combustion gases, soot, or windows. Boundary conditions and multiple layers are discussed with information on radiation in materials with nonunity refractive indices.

  9. PREFACE: 3rd International Workshop on Infrared Plasma Spectroscopy

    NASA Astrophysics Data System (ADS)

    Davies, P. B.; Röpcke, Jürgen; Hempel, Frank

    2009-07-01

    This volume containsd a selection of papers from the third Infrared Plasma Spectroscopy (IPS) Workshop held in Greifswald, Germany in July 2008. Although not all the contributions have been written up in time for the deadline for this volume, nevertheless the 12 contributions presented here give a fair representation of the conference topics. The conference comprised four different types of contribution. Firstly, four invited lectures focussed on the prime areas of interest. Secondly, eight shorter contributed talks, grouped as closely as possible with the appropriate invited lecture. These contributed talks covered topics in both pure and applied infrared plasma spectroscopy. A feature of the two previous IPS conferences has been a contribution from commercial organisations namely those involved in manufacturing devices, detectors and spectrometers. This group of participants formed the third part of the conference programme and gave five oral presentations covering topics like QCL and detector/detection developments and novel spectrometer designs. The fourth contributing group comprised 27 poster presentations. It should be mentioned that some of the latter were poster versions of contributed talks. The conference was remarkable for the wide spread of topics covered in a relatively small meeting, consisting of 44 participants. The participants were made up of 34 scientists from within Europe and 4 from the rest of the world. It is interesting to reflect on changes that have occurred since the previous meeting just a year earlier. Two clear developments which have occurred are the emergence of Quantum Cascade Lasers (QCL) and their use in Cavity Ring Down (CRD) spectroscopy. A major shift from cw lead salt diode lasers to cw and pulsed QCL in both pure and applied projects now seems to be well under way. The topics covered in the earlier conferences focussed more on applying infrared spectroscopy to plasma monitoring and control. When choosing the topics to cover the scientific committee felt that this time it would be useful to emphasise new spectroscopic developments as well as covering applications. This might serve as a guide as to where the subject of infrared spectroscopy in combination with plasma sources might be heading in the future i.e. to emphasize pure infrared spectroscopy developments. The first invited lecture (G Guelachvili and N Picque) and the last invited lecture (F K Tittel, Y Bakhirkin, R Curl, A Kosterev, R Lewicki, D Thomasz and S So) were chosen to set the scene and realise this objective. The second (R Engeln, R Zijlmans, S Welzel, O Gabriel, J-P van Helden, J Röpcke and D Schram) and third (X Aubert, C Lazzaroni, D Marinov, O Guaitella, S Welzel, A Pipa, J Röpcke and A Rousseau) invited talks focussed on the application of the IR laser techniques with particular emphasis on the role of surfaces in plasmas and the relevance of plasma surface interactions. Surface plasma interactions did not feature strongly in the two earlier meetings and so this topic too, along with the emphasis on novel infrared spectroscopy techniques, represents a new direction for the conference. Paul B Davies and Jürgen Röpcke International Scientific Committee P B Davies, Cambridge, UK: Chair J Röpcke, Greifswald, Germany: Co-Chair R Engeln, Eindhoven, Netherlands G Hancock, Oxford, U K M Hori, Nagoya, Japan H Linnartz, Leiden, Netherlands R Martini, New York, USA J Meichsner, Greifswald, Germany A Rousseau, Paris, France Local Organizing Committee J Röpcke (INP: Chair) F Hempel (INP: Secretary) J Meichsner (IfP, University of Greifswald) N Lang (INP) L Glawe (INP) C Krcka (INP) B Lindemann (INP) Conference photograph

  10. Parent Involvement in 3rd Grade Special Education

    ERIC Educational Resources Information Center

    Batt, Christine

    2011-01-01

    The focus of this study was to investigate how parent involvement impacts student motivation in third grade special education. The study was conducted at Allen Elementary in Genoa, Ohio during the spring of 2011. After reviewing recent literature, it acknowledges the importance of parent participation on student academic education, the effects of…

  11. Mechanical engineers' handbook, energy and power. 3rd ed.

    SciTech Connect

    Myer Kutz

    2005-12-15

    In addition to chapters on thermophysical properties of fluids, fundamentals of fluid mechanics, thermodynamics, heat transfer, combustion, and furnaces, Book 4 of the Handbook features coverage of both conventional (gaseous and liquid fuels, coal, and nuclear) and alternative (solar, geothermal, and fuel cells) energy sources, plus chapters on power machinery, refrigeration and cryogenics, environmental issues, and thermal systems optimization. Much of the material in this book is new or extensively revised, including coverage of such topics as: Heat pipes; Wind turbines; Fuel cells; Thermal systems optimization; Combustion; Fans, blowers, compressors, and pumps; Indoor environmental control; and Fluid power. Chapters of particular interest are: Combustion by Eric Eddings; Furnaces by Carroll Cone; Gaseous fuels by Richard J. Reed; Coals, lignite, peat by James Keppeler; and Air pollution-control technologies by C.A. Miller.

  12. 3rd International Conference on Turbulent Mixing and Beyond

    NASA Astrophysics Data System (ADS)

    Abarzhi, Snezhana I.; Gauthier, Serge; Keane, Christopher J.; Niemela, Joseph J.

    2013-07-01

    1. Introduction 'Turbulent Mixing and Beyond' (TMB) is the programme established for scientists, by scientists. It is merit-based, and is shaped by requirements of academic credentials, and novelty and quality of information. The goals of this programme are to expose the generic problem of non-equilibrium turbulent processes to a wide scientific community, to promote the development of new ideas in tackling the fundamental aspects of the problem, to assist in application of novel approaches in a broad range of phenomena, in which the turbulent processes occur, and to have a potential impact on technology. The programme was founded in 2007 with the support of the international scientific community and of the US National Science Foundation, the US Air Force Office of the Scientific Research and its European Office for Research and Development in the UK, the UNESCO-IAEA International Centre for Theoretical Physics in Italy, the Commissariat l'Energie Atomique in France, the US Department of Energy and the Department of Energy National Laboratories, the Institute for Laser Engineering in Japan, and the University of Chicago in the USA. The International Conference on Turbulent Mixing and Beyond provides opportunities to bring together researchers from the areas, which include but are not limited to, fluid dynamics, plasmas, high energy density physics, astrophysics, material science, combustion, atmospheric and earth sciences, nonlinear and statistical physics, applied mathematics, probability and statistics, data processing and computations, optics and communications, and to have their attention focused on the long-standing formidable task of non-equilibrium turbulent processes. 2. Non-equilibrium turbulent processes Non-equilibrium turbulent processes play a key role in a wide variety of phenomena, ranging from astrophysical to atomistic scales, under either high or low energy density conditions. Inertial confinement and magnetic fusion, light-matter interaction and non-equilibrium heat transfer, strong shocks and explosions, material transformation under high strain rate, supernovae and accretion discs, stellar non-Boussinesq and magneto-convection, planetary interiors and mantle-lithosphere tectonics, premixed and non-premixed combustion, non-canonical wall-bounded flows, hypersonic and supersonic boundary layers, dynamics of atmosphere and oceanography, are just a few examples to list. A grip on non-equilibrium turbulent processes is crucial for cutting-edge technology such as laser micro-machining, nano-electronics, free-space optical telecommunications and for industrial applications in the areas of aeronautics and aerodynamics. Non-equilibrium turbulent processes are anisotropic, non-local, multi-scale and multi-phase, and often are driven by shocks or acceleration. Their scaling, spectral and invariant properties differ substantially from those of classical Kolmogorov turbulence. At atomistic and meso-scales, the non-equilibrium dynamics depart dramatically from a standard scenario given by Gibbs statistic ensemble average and quasi-static Boltzmann equation. The singular aspect and the similarity of the non-equilibrium dynamics at macroscopic scales are interplayed with the fundamental properties of the Euler and compressible Navier-Stokes equations and with the problem sensitivity to the boundary conditions at discontinuities. The state-of-the-art numerical simulations of multi-phase flows suggest new methods for predictive modelling of the multi-scale non-equilibrium dynamics in fluids and plasmas, for error estimates and uncertainty quantifications, as well as for novel data assimilation techniques. 3. International Conference 'Turbulent Mixing and Beyond' The First and Second International Conferences on Turbulent Mixing and Beyond found that: (i) TMB-related problems have in common a set of outstanding research issues; (ii) their solution has a potential to significantly advance a variety of disciplines in science, technology and mathematics; (iii) TMB participants conduct highly innovative research and their

  13. Ectopic 3rd molar tooth in the maxillary antrum.

    PubMed

    Bello, Seidu A; Oketade, Ifeoluwa O; Osunde, Otasowie D

    2014-01-01

    Location of ectopic tooth in a nondentate area like the maxillary antrum is rare. A 17-year-old boy, with one year history of recurrent right facial swelling and radiographic finding of a maxillary third molar tooth located at the posterior wall of the maxillary antrum, is presented. Under endotracheal intubation, the tooth was extracted through a Caldwell-Luc antrostomy approach and patient had an uneventful recovery and has been symptom free for eight months. Ectopic tooth in the maxillary antrum is rare and is commonest with maxillary third molar. It may be symptomless but is more commonly associated with inflammatory symptoms. The treatment of choice is surgical excision which is mostly carried out with Caldwell-Luc approach, even though endoscopic approach is being reported. PMID:25132999

  14. Smith Newton Vehicle Performance Evaluation - 3rd Quarter 2012 (Brochure)

    SciTech Connect

    Not Available

    2013-03-01

    The Fleet Test and Evaluation Team at the U.S. Department of Energy's National Renewable Energy Laboratory is evaluating and documenting the performance of electric and plug-in hybrid electric drive systems in medium-duty trucks across the nation. Through this project, Smith Electric Vehicles will build and deploy 500 all-electric medium-duty trucks. The trucks will be deployed in diverse climates across the country.

  15. Legal Concepts in Sport: A Primer. 3rd Edition

    ERIC Educational Resources Information Center

    Carpenter, Linda Jean

    2008-01-01

    When most people think of legal issues in sport, they think about negligence. However, most professionals will face a much broader range of issues. For instance, topics such as sexual harassment, corporal punishment, drug testing, transportation, and hazing are all of special importance today. Also anti-discrimination laws and the concepts…

  16. Experimental Chaos - Proceedings of the 3rd Conference

    NASA Astrophysics Data System (ADS)

    Harrison, Robert G.; Lu, Weiping; Ditto, William; Pecora, Lou; Spano, Mark; Vohra, Sandeep

    1996-10-01

    The Table of Contents for the full book PDF is as follows: * Preface * Spatiotemporal Chaos and Patterns * Scale Segregation via Formation of Domains in a Nonlinear Optical System * Laser Dynamics as Hydrodynamics * Spatiotemporal Dynamics of Human Epileptic Seizures * Experimental Transition to Chaos in a Quasi 1D Chain of Oscillators * Measuring Coupling in Spatiotemporal Dynamical Systems * Chaos in Vortex Breakdown * Dynamical Analysis * Radial Basis Function Modelling and Prediction of Time Series * Nonlinear Phenomena in Polyrhythmic Hand Movements * Using Models to Diagnose, Test and Control Chaotic Systems * New Real-Time Analysis of Time Series Data with Physical Wavelets * Control and Synchronization * Measuring and Controlling Chaotic Dynamics in a Slugging Fluidized Bed * Control of Chaos in a Laser with Feedback * Synchronization and Chaotic Diode Resonators * Control of Chaos by Continuous-time Feedback with Delay * A Framework for Communication using Chaos Sychronization * Control of Chaos in Switching Circuits * Astrophysics, Meteorology and Oceanography * Solar-Wind-Magnetospheric Dynamics via Satellite Data * Nonlinear Dynamics of the Solar Atmosphere * Fractal Dimension of Scalar and Vector Variables from Turbulence Measurements in the Atmospheric Surface Layer * Mechanics * Escape and Overturning: Subtle Transient Behavior in Nonlinear Mechanical Models * Organising Centres in the Dynamics of Parametrically Excited Double Pendulums * Intermittent Behaviour in a Heating System Driven by Phase Transitions * Hydrodynamics * Size Segregation in Couette Flow of Granular Material * Routes to Chaos in Rotational Taylor-Couette Flow * Experimental Study of the Laminar-Turbulent Transition in an Open Flow System * Chemistry * Order and Chaos in Excitable Media under External Forcing * A Chemical Wave Propagation with Accelerating Speed Accompanied by Hydrodynamic Flow * Optics * Instabilities in Semiconductor Lasers with Optical Injection * Spatio-Temporal Dynamics of a Bimode CO2 Laser with Saturable Absorber * Chaotic Homoclinic Phenomena in Opto-Thermal Devices * Observation and Characterisation of Low-Frequency Chaos in Semiconductor Lasers with External Feedback * Condensed Matter * The Application of Nonlinear Dynamics in the Study of Ferroelectric Materials * Cellular Convection in a Small Aspect Ratio Liquid Crystal Device * Driven Spin-Wave Dynamics in YIG Films * Quantum Chaology in Quartz * Small Signal Amplification Caused by Nonlinear Properties of Ferroelectrics * Composite Materials Evolved from Chaos * Electronics and Circuits * Controlling a Chaotic Array of Pulse-Coupled Fitzhugh-Nagumo Circuits * Experimental Observation of On-Off Intermittency * Phase Lock-In of Chaotic Relaxation Oscillators * Biology and Medicine * Singular Value Decomposition and Circuit Structure in Invertebrate Ganglia * Nonlinear Forecasting of Spike Trains from Neurons of a Mollusc * Ultradian Rhythm in the Sensitive Plants: Chaos or Coloured Noise? * Chaos and the Crayfish Sixth Ganglion * Hardware Coupled Nonlinear Oscillators as a Model of Retina

  17. In Search of a Future. 3rd Edition, November 1976.

    ERIC Educational Resources Information Center

    Fulham, Stanley A.

    Describing the increasing numbers of Canada Natives who must reconcile the conflict arising from the economic necessity to migrate and the emotional necessity to stay in Manitoba's rural areas, this book identifies the following problems facing the rural to urban Canada Native migrant: lack of adequate housing; lack of finances; deficiency in…

  18. Prediction of Grade of Dropout from 3rd Grade Data.

    ERIC Educational Resources Information Center

    Lloyd, Dee Norman; Bleach, Gail

    Measures of background characteristics, school performance, and test achievement were analyzed for four race-by-sex samples of third graders who were known to have later become high school dropouts. In each sample, age in the third grade, course marks, and standardized achievement scores were found to be significantly related to the grade in which…

  19. Curriculum Based Assessment: A Primer. 3rd Edition

    ERIC Educational Resources Information Center

    Hargis, Charles H.

    2004-01-01

    The use of curriculum based assessment (CBA) to ensure learning disabled and low achieving students adequate educational opportunity remains the focus in this direct and comprehensive third edition. The additions to this edition are in the way of providing detail and explanation in the context of current and emerging issues in educational…

  20. Hospitals, nursing homes turn to 3rd-party financing

    SciTech Connect

    Slaff, J.

    1982-07-05

    Experience is teaching the administrators of hospitals and nursing homes how to make better arrangements for third-party financing of energy-management systems. Accustomed to health-insurance reimbursement for health-care costs, hospitals have lacked incentives for conservation. Plans now used most by hospitals and health-care facilities involve third-party arrangements where: (1) an equipment vendor installs equipment and takes a share of the energy-cost savings; or (2) energy-services firms both install capital-intensive equipment and implement a variety of low-cost conservation measures, again for a percentage of the savings. Although most users think these arrangements are satisfactory, they advise a preliminary low-cost audit and participation in a basic energy-management seminar before employing an energy-services firm. Accurate baseline energy-consumption data should be developed in order to evaluate results, and assurance is needed that staff members understand the accounting formulas. Also recommended are independent audits after installation and attention to the legal clauses in contracts. (DCK)

  1. [Neurology in the "3rd Reich" and consequences].

    PubMed

    Peiffer, J

    1998-08-01

    This review of German neurology during the Nazi era mentions first the significance of Jewish neurologists for the history of the specialty, and the irreplaceable loss that their expulsion from Germany represented. A brief discussion of the scientific accomplishments of German neurologists during this time is followed by a description of violations of ethical principles, exemplified by the human experiments of G. Schaltenbrand. The spirit of the age exerted a malevolent influence. PMID:9757428

  2. Basic imaging in congenital heart disease. 3rd Ed

    SciTech Connect

    Swischuk, L.E.; Sapire, D.W.

    1986-01-01

    The book retains its previous format with chapters on embryology, plain film interpretation, classification of pulmonary vascular patterns, cardiac malpositions and vascular anomalies, and illustrative cases. The book is organized with an abundance of illustrative figures, diagrams, and image reproductions. These include plain chest radiographs, angiograms, echocardiograms, and MR images. The authors present the pathophysiology and imaging of congenital heart lesions.

  3. Studies on Metadiscourse Since the 3rd Millennium

    ERIC Educational Resources Information Center

    Wei, Jing; Li, Yan; Zhou, Ting; Gong, Zhiwei

    2016-01-01

    Metadiscourse refer to linguistic resources that are used to refer to the act and the context of writing about some subject matter. Study of metadiscourse provides a gateway for understanding interactional features of texts or speech, looking beyond the ideational dimension of texts at how writers characterize the world and function…

  4. Pet Care Teaching Unit: 1st-3rd Grades.

    ERIC Educational Resources Information Center

    Peninsula Humane Society, San Mateo, CA.

    Activities in this unit are designed to familiarize primary grade students with the responsibilities involved in pet ownership. Teaching plans are provided for a total of 12 lessons involving social studies, language arts, math, and health sciences. Activities adaptable for readers and non-readers focus on pet overpopulation, care of pets when…

  5. Discipline with Dignity, 3rd Edition: New Challenges, New Solutions

    ERIC Educational Resources Information Center

    Curwin, Richard L.; Mendler, Allen N.; Mendler, Brian D.

    2008-01-01

    Since 1988, this landmark publication has given thousands of teachers timeless advice on not only how to prevent and solve discipline problems but also how to teach discipline as an affirming approach that promotes respect for self and others. Now this expanded 20th Anniversary Edition extends the authors' wisdom to new principles for coping with…

  6. Deployment simulation for 3rd generation solar array GSR3

    NASA Astrophysics Data System (ADS)

    Verne, C.; Rouchon, M.

    1989-01-01

    Deployment tests for different solar arrays are described. The Spacebus solar array deployment is tested in two dimensions. The Spot 4 array deployment is tested in three dimensions. A mock-up deployment test on an air cushion is compared to results obtained using simulation software. The third generation solar array concept equipped with Adele hinges is compared to previous solar array models. The need for greater accuracy and reliability in the deployment analysis of these third generation solar arrays is stressed.

  7. NS&T Management Observations - 3rd Quarter

    SciTech Connect

    David Gianotto

    2014-07-01

    The INL Management Observation Program (MOP) is designed to improve managers and supervisors understanding of work being performed by employees and the barriers impacting their success. The MOP also increases workers understanding of managements’ expectations as they relate to safety, security, quality, and work performance. Management observations are designed to improve the relationship and trust between employees and managers through increased engagement and interactions between managers and researchers in the field. As part of continuous improvement, NS&T management took initiative to focus on the participation and quality of observations in FY 14. This quarterly report is intended to (a) summarize the participation and quality of management’s observations, (b) assess observations for commonalities or trends related to facility or process barriers impacting research, and (c) provide feedback and make recommendations for improvements NS&T’s MOP.

  8. Resource Guide to Careers in Toxicology, 3rd Edition.

    ERIC Educational Resources Information Center

    Society of Toxicology, Reston, VA.

    This resource guide was prepared by the Tox 90's Educational Issues Task Force of the Society of Toxicology. The introduction provides information on the Society of Toxicology and financial support for graduate students in toxicology. Other sections include career opportunities in toxicology, academic and postdoctoral programs in toxicology, and…

  9. Low efficiency gratings for 3rd harmonic diagnostics applications

    SciTech Connect

    Britten, J.A.; Boyd, R.D.; Perry, M.D.; Shore, B.W.; Thomas, I.M.

    1995-08-09

    The baseline design of the National Ignition Facility (NIF) calls for sampling gratings to provide third-harmonic energy diagnostics in the highly constrained area of the target chamber. These 40 {times} 4O cm transmission gratings are to diffract at (order +1) nominally 0.3% of the incident 351 run light at a small angle on to a focusing mirror and into a calorimeter. The design calls for a plane grating of 500 lines/mm, and approximately 30 run deep, etched into a fused silica focusing lens and subsequently overcoated with a solgel anti reflective coating. Gratings of similar aperture and feature size have been produced for other applications by ion etching processes, but, in an effort to reduce substantially the cost of such optics, we are studying the feasibility of making these gratings by wet chemical etching techniques. Experimentation with high-quality fused silica substrates on 5 and 15 cm. scale has led to a wet etching process which can meet the design goals and which offers no significant scaleup barriers to full sized optics. The grating is produced by holographic exposure and a series of processing steps using only a photoresist mask and a final hydrofluoric acid etch. Gratings on 15 cm diameter test substrates exhibit absolute diffraction efficiencies from 0.2--0.4% with a standard deviation of about 15% of the mean over the full aperture. The efficiency variation is due to variation in linewidth caused by spatial nonuniformities in exposure energy. Uniformity improvements can be realized by using a smaller, more uniform portion of the exposure beam and exposing for longer times. The laser damage threshold for these gratings has been measured at LLNL and found to be identical to that of the fused silica substrate.

  10. IVHM for the 3rd Generation RLV Program: Technology Development

    NASA Technical Reports Server (NTRS)

    Kahle, Bill

    2000-01-01

    The objective behind the Integrated Vehicle Health Management (IVHM) project is to develop and integrate the technologies which can provide a continuous, intelligent, and adaptive health state of a vehicle and use this information to improve safety and reduce costs of operations. Technological areas discussed include: developing, validating, and transfering next generation IVHM technologies to near term industry and government reusable launch systems; focus NASA on the next generation and highly advanced sensor and software technologies; and validating IVHM systems engineering design process for future programs.

  11. Ethnic Orange County: An Ethnic Resources Directory. 3rd Edition.

    ERIC Educational Resources Information Center

    Garcia-Ayvens, Francisco, Comp.

    Designed to assist libraries and other agencies in their efforts to provide current referral services to local groups and agencies serving minority populations, this directory reflects the diverse nature of Orange County's population and identifies resources to help support their basic needs. Limited to the four largest minority groups (Asian…

  12. [Infant Mortality in Argentina: reducibility criteria, 3rd review].

    PubMed

    Finkelstein, Juliana Zoe; Duhau, Mariana; Abeyá Gilardon, Enrique; Ferrario, Claudia; Speranza, Ana; Asciutto, Carolina; Marconi, Élida; Guevel, Carlos; Fernández, María de las Mercedes; Martínez, María Laura; Santoro, Adrián; Loiacono, Karina; Lomuto, Celia

    2015-08-01

    The infant mortality rate is an indicator of quality of life, development, and quality and accessibility of health care. Improvements in science, technology and better access to health care have contributed to a major decrease in the infant mortality rate in Argentina. Since the 1980s, infant deaths have been classified based on the opportunities for reducibility yielded by scientific knowledge and available technologies, in order to obtain a basis for the monitoring and implementation of health policies. The last review of this classification was in 2011. In 2012, a total of 5,541 neonatal deaths (less than 28 days of life) were registered and, under this new classification, over 61% were reducible mainly by the improvement of perinatal health care and adequate and timely treatment of the at-risk newborn. In 2012, a total of 2,686 post-neonatal deaths (from 28 days of life to a year) were registered and, under this new classification, over 66.8% were reducible by improving prevention strategies and providing adequate and timely treatment. This new analysis demonstrates the need to improve the opportunity, accessibility and quality of perinatal care starting at pregnancy, guaranteeing quality care at delivery and reinforcing prevention and timely treatment of common diseases in childhood over the first year of life. PMID:26172012

  13. Developmental Surface and Phonological Dysgraphia in German 3rd Graders

    ERIC Educational Resources Information Center

    Cholewa, Jurgen; Mantey, Stefanie; Heber, Stefanie; Hollweg, Wibke

    2010-01-01

    The investigation of developmental reading and spelling disorders within the framework provided by cognitive neuropsychology has yielded interesting results for several alphabetic orthographies, for example English, Italian, and French. However, this approach has not attracted much attention in German speaking countries up to now. The following…

  14. Centaur upper stage

    NASA Astrophysics Data System (ADS)

    Groesbeck, W.

    An account is given of the design features of the LOX/LH2-fueled Centaur upper stage engine and fuel cryotankage, in order to serve as a basis for understanding the Main Engine Cut Off (MECO) system instituted. MECO follows the instant of spacecraft separation from the upper stage. The planetary launch program during 1966-1978 involved 23 Centaur launches and led to no upper stage reentry; LEO missions for HEAO and OAO satellite lofting in 1963-1979 involved nine Centaur launches and led to five reentries. GEO satellite launches in 1969-1986 saw 32 launches and three known reentries.

  15. Prostate cancer staging

    MedlinePlus

    ... effects of treatment The chance that treatment can cure your cancer or help you in other ways With stage ... III prostate cancer, the main goal is to cure the cancer by treating it and keeping it from coming ...

  16. Stages of Pancreatic Cancer

    MedlinePlus

    ... cancer) cells form in the tissues of the pancreas. The pancreas is a gland about 6 inches ... spleen , and bile ducts . Tests that examine the pancreas are used to detect (find), diagnose, and stage ...

  17. Stages of Pregnancy

    MedlinePlus

    ... your baby in these three stages. First trimester (week 1-week 12) First trimester See how your baby is ... is each pregnancy. Return to top Second trimester (week 13-week 28) Second trimester See how your ...

  18. Cryogenic Propulsion Stage

    NASA Technical Reports Server (NTRS)

    Jones, David

    2011-01-01

    The CPS is an in-space cryogenic propulsive stage based largely on state of the practice design for launch vehicle upper stages. However, unlike conventional propulsive stages, it also contains power generation and thermal control systems to limit the loss of liquid hydrogen and oxygen due to boil-off during extended in-space storage. The CPS provides the necessary (Delta)V for rapid transfer of in-space elements to their destinations or staging points (i.e., E-M L1). The CPS is designed around a block upgrade strategy to provide maximum mission/architecture flexibility. Block 1 CPS: Short duration flight times (hours), passive cryo fluid management. Block 2 CPS: Long duration flight times (days/weeks/months), active and passive cryo fluid management.

  19. Staging Airliner Service

    NASA Technical Reports Server (NTRS)

    Hahn, Andrew S.

    2007-01-01

    There is a general consensus building that historically high fuel prices and greater public awareness of the emissions that result from burning fuel are going to be long-term concerns for those who design, build, and operate airliners. The possibility of saving both fuel and reducing emissions has rekindled interest in breaking very long-range airline flights into multiple stages or even adopting in-flight refueling. It is likely that staging will result in lower fuel burn, and recent published reports have suggested that the savings are substantial, particularly if the airliner is designed from the outset for this kind of operation. Given that staging runs against the design and operation historical trend, this result begs for further attention. This paper will examine the staging question, examining both analytic and numeric performance estimation methodologies to quantify the likely amount of fuel savings that can be expected and the resulting design impacts on the airliner.

  20. Understanding cancer staging

    MedlinePlus

    ... the body. The spread of cancer is called metastasis . Cancer staging is used to help describe the ... cancer has spread to nearby lymph nodes (N) Metastasis (M) , or if and how much the cancer ...

  1. Bioimpedance Spectroscopy in Detecting Lower-Extremity Lymphedema in Patients With Stage I, Stage II, Stage III, or Stage IV Vulvar Cancer Undergoing Surgery and Lymphadenectomy

    ClinicalTrials.gov

    2016-02-09

    Lymphedema; Perioperative/Postoperative Complications; Stage IA Vulvar Cancer; Stage IB Vulvar Cancer; Stage II Vulvar Cancer; Stage IIIA Vulvar Cancer; Stage IIIB Vulvar Cancer; Stage IIIC Vulvar Cancer; Stage IVA Vulvar Cancer; Stage IVB Vulvar Cancer

  2. Precision adjustable stage

    DOEpatents

    Cutburth, Ronald W.; Silva, Leonard L.

    1988-01-01

    An improved mounting stage of the type used for the detection of laser beams is disclosed. A stage center block is mounted on each of two opposite sides by a pair of spaced ball bearing tracks which provide stability as well as simplicity. The use of the spaced ball bearing pairs in conjunction with an adjustment screw which also provides support eliminates extraneous stabilization components and permits maximization of the area of the center block laser transmission hole.

  3. Multiple stage railgun

    DOEpatents

    Hawke, Ronald S.; Scudder, Jonathan K.; Aaland, Kristian

    1982-01-01

    A multiple stage magnetic railgun accelerator (10) for accelerating a projectile (15) by movement of a plasma arc (13) along the rails (11,12). The railgun (10) is divided into a plurality of successive rail stages (10a-n) which are sequentially energized by separate energy sources (14a-n) as the projectile (15) moves through the bore (17) of the railgun (10). Propagation of energy from an energized rail stage back towards the breech end (29) of the railgun (10) can be prevented by connection of the energy sources (14a-n) to the rails (11,12) through isolation diodes (34a-n). Propagation of energy from an energized rail stage back towards the breech end of the railgun can also be prevented by dividing the rails (11,12) into electrically isolated rail sections (11a-n, 12a-n). In such case means (55a-n) are used to extinguish the arc at the end of each energized stage and a fuse (31) or laser device (61) is used to initiate a new plasma arc in the next energized rail stage.

  4. Chemotherapy Toxicity On Quality of Life in Older Patients With Stage I, Stage II, Stage III, or Stage IV Ovarian Epithelial, Primary Peritoneal Cavity, or Fallopian Tube Cancer

    ClinicalTrials.gov

    2016-02-09

    Stage I Ovarian Cancer; Stage IA Fallopian Tube Cancer; Stage IB Fallopian Tube Cancer; Stage IC Fallopian Tube Cancer; Stage II Ovarian Cancer; Stage IIA Fallopian Tube Cancer; Stage IIB Fallopian Tube Cancer; Stage IIC Fallopian Tube Cancer; Stage III Ovarian Cancer; Stage III Primary Peritoneal Cancer; Stage IIIA Fallopian Tube Cancer; Stage IIIB Fallopian Tube Cancer; Stage IIIC Fallopian Tube Cancer; Stage IV Fallopian Tube Cancer; Stage IV Ovarian Cancer; Stage IV Primary Peritoneal Cancer

  5. Principles of Melanoma Staging.

    PubMed

    Boland, Genevieve M; Gershenwald, Jeffrey E

    2016-01-01

    Although now commonplace in contemporary cancer care, the systematic approach to classification of disease-specific cancers into a formalized staging system is a relatively modern concept. Overall, the goals of cancer staging are to characterize the status of cancer at a specific moment in time, risk stratify, facilitate prognostication, and inform clinical decision making. The revisions to the American Joint Committee on Cancer (AJCC) melanoma staging system over time reflect changes in our understanding of the biology of the disease. Since the 1st edition, where tumor thickness was defined anatomically by its relationship to the reticular or papillary dermis (Clark level) as well as tumor thickness (Breslow thickness), there have been significant strides in our use of clinicopathological variables to stratify low- versus high-risk patients. Management of the regional nodal basin has also changed dramatically over time, impacted by techniques such as lymphatic mapping and sentinel lymph node biopsy (SLNB) and changes in pathological evaluation of the regional lymph nodes. Additionally, stratification of distant metastases has evolved as survival outcomes have been shown to vary based upon anatomic site of metastases and serum lactate dehydrogenase levels. The variables in use in the current (7th edition) AJCC staging system are surrogate markers of biology with validated impact of survival outcomes. Going forward, it is likely that these and additional clinicopathological factors will be integrated with molecular and other correlates of melanoma tumor biology to further refine and personalize melanoma staging. PMID:26601861

  6. New School Stages for Old.

    ERIC Educational Resources Information Center

    Miller, James Hull

    A new and dynamic approach to auditorium stage design is presented. Contents include--(1) modified proscenium stage plan--a definition, (2) benefits of a modified proscenium stage plan, and (3) details of a modified proscenium stage plan--basic concepts, a typical layout, projection systems, and scenic design for space stage. (RH)

  7. 2-Stage Classification Modeling

    1994-11-01

    CIRCUIT2.4 is used to design optimum two-stage classification configurations and operating conditions for energy conservation. It permits simulation of five basic grinding-classification circuits, including one single-stage and four two-stage classification arrangements. Hydrocyclones, spiral classifiers, and sieve band screens can be simulated, and the user may choose the combination of devices for the flowsheet simulation. In addition, the user may select from four classification modeling methods to achieve the goals of a simulation project using themore » most familiar concepts. Circuit performance is modeled based on classification parameters or equipment operating conditions. A modular approach was taken in designing the program, which allows future addition of other models with relatively minor changes.« less

  8. Adaptation of the Ages and Stages Questionnaire for Remote Aboriginal Australia.

    PubMed

    D'Aprano, Anita; Silburn, Sven; Johnston, Vanessa; Robinson, Gary; Oberklaid, Frank; Squires, Jane

    2016-04-01

    A key challenge to providing quality developmental care in remote Aboriginal primary health care (PHC) centers has been the absence of culturally appropriate developmental screening instruments. This study focused on the cross-cultural adaptation of the Ages and Stages Questionnaires, 3rd edition (ASQ-3), with careful attention to language and culture. We aimed to adapt the ASQ-3 for use with remote dwelling Australian Aboriginal children, and to investigate the cultural appropriateness and feasibility of the adapted ASQ-3 for use in this context. We undertook a qualitative study in two remote Australian Aboriginal communities, using a six-step collaborative adaptation process. Aboriginal Health Workers (AHWs) were trained to use the adapted ASQ-3, and follow-up interviews examined participants' views of the cultural acceptability and usefulness of the adapted instrument. The adapted ASQ-3 was found to have high face validity and to be culturally acceptable and relevant to parents, AHWs, and early childhood development experts. PMID:25488936

  9. Evaluation of body weight, body mass index, and body fat percentage changes in early stages of fixed orthodontic therapy

    PubMed Central

    Sandeep, K. Sai; Singaraju, Gowri Sankar; Reddy, V. Karunakar; Mandava, Prasad; Bhavikati, Venkata N.; Reddy, Rohit

    2016-01-01

    Aim: The aim of this study was to evaluate and compare the changes in body weight, body mass index (BMI), and body fat percentage (BFP) during the initial stages of fixed orthodontic treatment. Materials and Methods: The sample for this observational prospective study included 68 individuals with fixed orthodontic appliance in the age group of 18–25 years of both the sexes (25 males and 43 females). The control group consisted of 60 individuals (24 males and 36 females). The weight, BMI, and BFP were measured using a Body Composition Monitor at three points of time “T1” initial; “T2” after 1 month; and “T2” after 3 months. The results were tabulated and analyzed with the Statistical Package for the Social Sciences software. The mean changes between different parameters in both the study and control groups and between males and females in the study group was compared by using two-tailed unpaired student's t-test. The statistical significance is set atP ≤ 0.05. Results: There was an overall decrease in the body weight, BMI, and BFP after 1 month in the study cohort, which was statistically significant compared to the control group (P < 0.0001). This was followed by an increase in the parameters after the end of the 3rd month. Comparison of the parameters between the study and control group at the start of the treatment and at the end of the 3rd month had no statistical significance. There was a marked variation in the changes of these parameters between males and females of the study group, which is statistically significant (<0.0001). Conclusion: There is a definite reduction in the weight, BMP, and BMI at the end of the first month followed by a gain of weight, but not at the initial point by the end of the 3rd month. PMID:27583224

  10. Stage cementing apparatus

    SciTech Connect

    Blamford, D.M.; Easter, J.H.

    1988-06-21

    A stage cementing apparatus for selectively passing cement from the interior passage of a casing to the annulus between the exterior of the casing and borehole, the casing having an upper portion and a lower portion, is described comprising: a barrel secured to the upper portion of the casing; a mandrel secured to the lower portion of the casing, and a stage cementing tool having a generally cylindrical configuration adapted for attachment to the lower end of the barrel about a portion of the mandrel.

  11. Staged fluidized bed

    DOEpatents

    Mallon, R.G.

    1983-05-13

    The invention relates to oil shale retorting and more particularly to staged fluidized bed oil shale retorting. Method and apparatus are disclosed for narrowing the distribution of residence times of any size particle and equalizing the residence times of large and small particles in fluidized beds. Particles are moved up one fluidized column and down a second fluidized column with the relative heights selected to equalize residence times of large and small particles. Additional pairs of columns are staged to narrow the distribution of residence times and provide complete processing of the material.

  12. End-Stage.

    ERIC Educational Resources Information Center

    Moua, Mai Neng

    2001-01-01

    Through her reflections on dealing with dialysis for end-stage renal disease and awaiting a kidney transplant, the author presents insights into how her experience was shaped by the physical, emotional, and multicultural forces she faced. Among the issues discussed are her ambivalent feelings between pursuing a regular lifestyle and receiving…

  13. "Stage 40" Handbook.

    ERIC Educational Resources Information Center

    Mill River Union High School, North Clarendon, VT.

    The policies, purposes, and guidelines of "Stage 40," an educational repertory company for students, are presented in this paper, which also explains how the company functions. The paper discusses the company's history, the relationship between the company and academics, and the responsibilities of a company member. Letters by the board members…

  14. The Scribble Stage

    ERIC Educational Resources Information Center

    Douglas, Katherine

    2012-01-01

    The term "Scribble Stage" highlights how first efforts appear in student independent work. Age does not correlate with "scribble" work as does experience; upper grade students and even adults will often approach new materials and techniques in an experimental manner as a means to become familiar with them. Everyone is a beginner at the things they…

  15. Stage a Water Show

    ERIC Educational Resources Information Center

    Frasier, Debra

    2008-01-01

    In the author's book titled "The Incredible Water Show," the characters from "Miss Alaineus: A Vocabulary Disaster" used an ocean of information to stage an inventive performance about the water cycle. In this article, the author relates how she turned the story into hands-on science teaching for real-life fifth-grade students. The author also…

  16. Pancreatic Cancer Stage 4

    MedlinePlus

    ... lung, liver, and peritoneal cavity. An inset shows cancer cells spreading from the pancreas, through the blood and lymph system, to another ... abdomen that contains the intestines, stomach, and liver). Cancer may also have spread to ... pancreas or to lymph nodes. Stage IV pancreatic cancer. ...

  17. Crescentic ramp turbine stage

    NASA Technical Reports Server (NTRS)

    Lee, Ching-Pang (Inventor); Tam, Anna (Inventor); Kirtley, Kevin Richard (Inventor); Lamson, Scott Henry (Inventor)

    2007-01-01

    A turbine stage includes a row of airfoils joined to corresponding platforms to define flow passages therebetween. Each airfoil includes opposite pressure and suction sides and extends in chord between opposite leading and trailing edges. Each platform includes a crescentic ramp increasing in height from the leading and trailing edges toward the midchord of the airfoil along the pressure side thereof.

  18. STS upper stage operations

    NASA Technical Reports Server (NTRS)

    Kitchens, M. D.; Schnyer, A. D.

    1977-01-01

    Several design/development and operational approaches for STS upper stages are being pursued to realize maximum operational and economic benefits upon the introduction of the STS in the 1980s. The paper focuses special attention on safety operations, launch site operations and on-orbit operations.

  19. Effects of gamma irradiation on different stages of mealybug Dysmicoccus neobrevipes (Hemiptera: Pseudococcidae)

    NASA Astrophysics Data System (ADS)

    The, Doan Thi; Khanh, Nguyen Thuy; Lang, Vo Thi Kim; Van Chung, Cao; An, Tran Thi Thien; Thi, Nguyen Hoang Hanh

    2012-01-01

    Utilization of phytosanitary irradiation as a potential treatment to disinfest agricultural commodities in trade has expanded rapidly in the recent years. Cobalt-60 gamma ray target doses of 100, 150, 200 and 250 Gy were used to irradiate immatures and adults of Dysmicoccus neobrevipes (Beardsley) (Hemiptera: Pseudococcidae) infesting dragon fruits to find the most tolerant stage and the most optimal dose range for quarantine treatment. In general, irradiation affected significantly all life stages of D. neobrevipes mortality and adult reproduction. The pattern of tolerance to irradiation in D. neobrevipes was 1st instars<2nd instars<3rd instarsstage. Based on obtained results after 21 days of irradiation, predicted doses for 100% mortality of each different development stage in the above mentioned pattern were 224.6, 241.3, 330.9 and 581.5 Gy, respectively. No survived female adult produced offspring at 200 and 250 Gy. Dose range between 200 and 250 Gy could be efficient to prevent the reproduction of this mealybug.

  20. A Multi-Stage Reverse Logistics Network Problem by Using Hybrid Priority-Based Genetic Algorithm

    NASA Astrophysics Data System (ADS)

    Lee, Jeong-Eun; Gen, Mitsuo; Rhee, Kyong-Gu

    Today remanufacturing problem is one of the most important problems regarding to the environmental aspects of the recovery of used products and materials. Therefore, the reverse logistics is gaining become power and great potential for winning consumers in a more competitive context in the future. This paper considers the multi-stage reverse Logistics Network Problem (m-rLNP) while minimizing the total cost, which involves reverse logistics shipping cost and fixed cost of opening the disassembly centers and processing centers. In this study, we first formulate the m-rLNP model as a three-stage logistics network model. Following for solving this problem, we propose a Genetic Algorithm pri (GA) with priority-based encoding method consisting of two stages, and introduce a new crossover operator called Weight Mapping Crossover (WMX). Additionally also a heuristic approach is applied in the 3rd stage to ship of materials from processing center to manufacturer. Finally numerical experiments with various scales of the m-rLNP models demonstrate the effectiveness and efficiency of our approach by comparing with the recent researches.

  1. MICE Staging and Status

    SciTech Connect

    Hanlet, Pierrick

    2010-03-30

    Ionization cooling will be a key technique for a high-intensity Neutrino Factory or Muon Collider. The Muon Ionization Cooling Experiment (MICE) is a high-precision, staged accelerator experiment being performed at Rutherford Appleton Laboratory in the UK. Its goal is the first demonstration, with 0.1% resolution, of the feasibility of reducing the transverse emittance of a beam of muons by ionization cooling in low-Z absorbers. MICE is being staged in the following steps: I. Creating and characterizing a beam of muons; II. Measuring their emittance; III. Systematic comparison of successive measurements; IV. Inserting absorber; V. Reaccelerating longitudinally; and VI. Complete '10%-cooling' test. Step I is currently in progress with Step II to commence next year; completion of Step VI is anticipated in approx2012.

  2. MICE Staging and Status

    NASA Astrophysics Data System (ADS)

    Hanlet, Pierrick

    2010-03-01

    Ionization cooling will be a key technique for a high-intensity Neutrino Factory or Muon Collider. The Muon Ionization Cooling Experiment (MICE) is a high-precision, staged accelerator experiment being performed at Rutherford Appleton Laboratory in the UK. Its goal is the first demonstration, with 0.1% resolution, of the feasibility of reducing the transverse emittance of a beam of muons by ionization cooling in low-Z absorbers. MICE is being staged in the following steps: I. Creating and characterizing a beam of muons; II. Measuring their emittance; III. Systematic comparison of successive measurements; IV. Inserting absorber; V. Reaccelerating longitudinally; and VI. Complete "10%-cooling" test. Step I is currently in progress with Step II to commence next year; completion of Step VI is anticipated in ˜2012.

  3. Staged Event Architecture

    2005-05-30

    Sea is a framework for a Staged Event Architecture, designed around non-blocking asynchronous communication facilities that are decoupled from the threading model chosen by any given application, Components for P networking and in-memory communication are provided. The Sea Java library encapsulates these concepts. Sea is used to easily build efficient and flexible low-level network clients and servers, and in particular as a basic communication substrate for Peer-to-Peer applications.

  4. Endometrial carcinoma stage I.

    PubMed

    Baram, A; Ron, I; Kupferminc, M; Inbar, M

    1997-01-01

    Standard staging and therapeutic approach to endometrial cancer involves lymph node sampling (LNS) at the time of total abdominal hysterectomy (TAH) and bilateral salpingo-oophorectomy (BSO). Lymphadenectomy prolongs time of surgery and increases the risk of morbidity; where other predictors are available, it may not contribute important supplementary information. 185/247 women with stage I endometrial carcinoma underwent the standard surgery while 62 underwent TAH+BSO. Recurrence and survival were monitored for a mean of 6.5 years and retrospectively reviewed: the rates for groups with and without known lymph node status were alike [13.5% (25/185) recurrence for the former and 12.9% (8/62) for the latter, and 5-year survival rates of 75.7% (140/185) for the former and 74.2 (46/62) for the latter]. Myometrial invasion and histological grade appeared to have been highly accurate predictors without lymph node information. Because information on histological grade is available early and is highly predictive, its use could be incorporated into a revised management algorithm for stage I endometrial cancer which would depend upon ensuring lymphadenectomy for women with low grade histopathology and omitting it for those with high grades on the grounds that no further information is necessary to act appropriately. PMID:21590195

  5. Rituximab and Oblimersen in Treating Patients With Stage II, Stage III, or Stage IV Follicular Non-Hodgkin's Lymphoma

    ClinicalTrials.gov

    2013-01-04

    Stage III Grade 1 Follicular Lymphoma; Stage III Grade 2 Follicular Lymphoma; Stage III Grade 3 Follicular Lymphoma; Stage IV Grade 1 Follicular Lymphoma; Stage IV Grade 2 Follicular Lymphoma; Stage IV Grade 3 Follicular Lymphoma

  6. Staged cascade fluidized bed combustor

    DOEpatents

    Cannon, Joseph N.; De Lucia, David E.; Jackson, William M.; Porter, James H.

    1984-01-01

    A fluid bed combustor comprising a plurality of fluidized bed stages interconnected by downcomers providing controlled solids transfer from stage to stage. Each stage is formed from a number of heat transfer tubes carried by a multiapertured web which passes fluidizing air to upper stages. The combustor cross section is tapered inwardly from the middle towards the top and bottom ends. Sorbent materials, as well as non-volatile solid fuels, are added to the top stages of the combustor, and volatile solid fuels are added at an intermediate stage.

  7. Treatment Options by Stage (Anal Cancer)

    MedlinePlus

    ... following stages are used for anal cancer: Stage 0 (Carcinoma in Situ) In stage 0 , abnormal cells ... or check-ups. Treatment Options by Stage Stage 0 (Carcinoma in Situ) Treatment of stage 0 is ...

  8. Chimpanzee sleep stages.

    NASA Technical Reports Server (NTRS)

    Freemon, F. R.; Mcnew, J. J.; Adey, W. R.

    1971-01-01

    The electroencephalogram and electro-oculogram of two unrestrained juvenile chimpanzees was monitored for 7 consecutive nights using telemetry methods. Of the sleeping time, 23% was spent in the rapid eye movement of REM type of sleep, whereas 8, 4, 15, and 10% were spent in non-REM stages 1 through 4, respectively. Seven to nine periods of REM sleep occurred per night. The average time from the beginning of one REM period to the beginning of the next was approximately 85 min.

  9. Nuclear Cryogenic Propulsion Stage

    NASA Technical Reports Server (NTRS)

    Houts, Michael G.; Borowski, S. K.; George, J. A.; Kim, T.; Emrich, W. J.; Hickman, R. R.; Broadway, J. W.; Gerrish, H. P.; Adams, R. B.

    2012-01-01

    The fundamental capability of Nuclear Thermal Propulsion (NTP) is game changing for space exploration. A first generation Nuclear Cryogenic Propulsion Stage (NCPS) based on NTP could provide high thrust at a specific impulse above 900 s, roughly double that of state of the art chemical engines. Characteristics of fission and NTP indicate that useful first generation systems will provide a foundation for future systems with extremely high performance. The role of the NCPS in the development of advanced nuclear propulsion systems could be analogous to the role of the DC-3 in the development of advanced aviation. Progress made under the NCPS project could help enable both advanced NTP and advanced NEP.

  10. Early Diagnosis and Staging.

    PubMed

    Lilja, H; Lilja, D R H

    1999-01-01

    This report reviews developments in the early diagnosis and staging of prostate cancer and updated on the incidence of postate cancer to discuss the pros and cons of population based screening. Refinements and reliability of various diagnosic procedures are described such as PSA testing, transrectal ultrasound, ratio beteen PSA-level and ultrasound measured prostate volume, rate of change of PSA-level, combination factor equations computed by neural network programs to predict likelihood of prostate cancer, artificial neural network analysis of subvisual transrectal ultrasound information, measurements of different PSA-forms of PSA (in particular percent free PSA), and glandular kallikrein 2. PMID:12496851

  11. Dual stage check valve

    NASA Technical Reports Server (NTRS)

    Whitten, D. E. (Inventor)

    1973-01-01

    A dual stage seat valve head arrangement is described which consists of a primary sealing point located between a fixed orifice seat and a valve poppet, and a secondary sealing point between an orifice poppet and a valve poppet. Upstream of the valve orifice is a flexible, convoluted metal diaphragm attached to the orifice poppet. Downstream of the valve orifice, a finger spring exerts a force against the valve poppet, tending to keep the valve in a closed position. The series arrangement of a double seat and poppet is able to tolerate small particle contamination while minimizing chatter by controlling throttling or metering across the secondary seat, thus preserving the primary sealing surface.

  12. Changes in Brain Function in Patients With Stage I, Stage II, Stage III, or Stage IV Ovarian, Primary Peritoneal, or Fallopian Tube Cancer Who Are Receiving Chemotherapy

    ClinicalTrials.gov

    2016-02-09

    Cognitive Side Effects of Cancer Therapy; Malignant Ovarian Epithelial Tumor; Malignant Ovarian Mixed Epithelial Tumor; Ovarian Brenner Tumor; Ovarian Carcinosarcoma; Ovarian Choriocarcinoma; Ovarian Clear Cell Cystadenocarcinoma; Ovarian Dysgerminoma; Ovarian Embryonal Carcinoma; Ovarian Endometrioid Adenocarcinoma; Ovarian Mixed Germ Cell Tumor; Ovarian Mucinous Cystadenocarcinoma; Ovarian Polyembryoma; Ovarian Sarcoma; Ovarian Serous Cystadenocarcinoma; Ovarian Teratoma; Ovarian Yolk Sac Tumor; Stage I Ovarian Cancer; Stage IA Fallopian Tube Cancer; Stage IA Ovarian Cancer; Stage IA Ovarian Germ Cell Tumor; Stage IB Fallopian Tube Cancer; Stage IB Ovarian Cancer; Stage IB Ovarian Germ Cell Tumor; Stage IC Fallopian Tube Cancer; Stage IC Ovarian Cancer; Stage IC Ovarian Germ Cell Tumor; Stage II Ovarian Cancer; Stage IIA Fallopian Tube Cancer; Stage IIA Ovarian Cancer; Stage IIA Ovarian Germ Cell Tumor; Stage IIB Fallopian Tube Cancer; Stage IIB Ovarian Cancer; Stage IIB Ovarian Germ Cell Tumor; Stage IIC Fallopian Tube Cancer; Stage IIC Ovarian Cancer; Stage IIC Ovarian Germ Cell Tumor; Stage IIIA Fallopian Tube Cancer; Stage IIIA Ovarian Cancer; Stage IIIA Ovarian Germ Cell Tumor; Stage IIIA Primary Peritoneal Cancer; Stage IIIB Fallopian Tube Cancer; Stage IIIB Ovarian Cancer; Stage IIIB Ovarian Germ Cell Tumor; Stage IIIB Primary Peritoneal Cancer; Stage IIIC Fallopian Tube Cancer; Stage IIIC Ovarian Cancer; Stage IIIC Ovarian Germ Cell Tumor; Stage IIIC Primary Peritoneal Cancer; Stage IV Fallopian Tube Cancer; Stage IV Ovarian Cancer; Stage IV Ovarian Germ Cell Tumor; Stage IV Primary Peritoneal Cancer; Undifferentiated Ovarian Carcinoma

  13. Design of a 3-stage ADR for the soft x-ray spectrometer instrument on the ASTRO-H mission

    NASA Astrophysics Data System (ADS)

    Shirron, Peter J.; Kimball, Mark O.; Wegel, Donald C.; Canavan, Edgar R.; Dipirro, Michael J.

    2010-07-01

    The Japanese Astro-H mission will include the Soft X-ray Spectrometer (SXS) instrument, whose 36-pixel detector array of ultra-sensitive x-ray microcalorimeters requires cooling to 50 mK. This will be accomplished using a 3-stage adiabatic demagnetization refrigerator (ADR). The design is dictated by the need to operate with full redundancy with both a superfluid helium dewar at 1.3 K or below, and with a 4.5 K Joule-Thomson (JT) cooler. The ADR is configured as a 2-stage unit that is located in a well in the helium tank, and a third stage that is mounted to the top of the helium tank. The third stage is directly connected through two heat switches to the JT cooler and the helium tank, and manages heat flow between the two. When liquid helium is present, the 2-stage ADR operates in a single-shot manner using the superfluid helium as a heat sink. The third stage may be used independently to reduce the time-average heat load on the liquid to extend its lifetime. When the liquid is depleted, the 2nd and 3rd stages operate as a continuous ADR to maintain the helium tank at as low a temperature as possible - expected to be 1.2 K - and the 1st stage cools from that temperature as a single-stage, single-shot ADR. The ADR's design and operating modes are discussed, along with test results of the prototype 3-stage ADR.

  14. Design of a 3-Stage ADR for the Soft X-Ray Spectrometer Instrument on the Astro-H Mission

    NASA Technical Reports Server (NTRS)

    Shirron, Peter J.; Kimball, Mark O.; Wegel, Donald C.; Canavan, Edgar R.; DiPirro, Michael J.

    2011-01-01

    The Japanese Astro-H mission will include the Soft X-ray Spectrometer (SXS) instrument, whose 36-pixel detector array of ultra-sensitive x-ray microcalorimeters requires cooling to 50 mK. This will be accomplished using a 3-stage adiabatic demagnetization refrigerator (ADR). The design is dictated by the need to operate with full redundancy with both a superfluid helium dewar at 1.3 K or below, and with a 4.5 K Joule-Thomson (JT) cooler. The ADR is configured as a 2-stage unit that is located in a well in the helium tank, and a third stage that is mounted to the top of the helium tank. The third stage is directly connected through two heat switches to the JT cooler and the helium tank, and manages heat flow between the two. When liquid helium is present, the 2-stage ADR operates in a single-shot manner using the superfluid helium as a heat sink. The third stage may be used independently to reduce the time-average heat load on the liquid to extend its lifetime. When the liquid is depleted, the 2nd and 3rd stages operate as a continuous ADR to maintain the helium tank at as low a temperature as possible - expected to be 1.2 K - and the 1st stage cools from that temperature as a single-stage, single-shot ADR. The ADR s design and operating modes are discussed, along with test results of the prototype 3-stage ADR.

  15. Upper stage technology evaluation studies

    NASA Technical Reports Server (NTRS)

    1972-01-01

    Studies to evaluate advanced technology relative to chemical upper stages and orbit-to-orbit stages are reported. The work described includes: development of LH2/LOX stage data, development of data to indicate stage sensitivity to engine tolerance, modified thermal routines to accommodate storable propellants, added stage geometries to computer program for monopropellant configurations, determination of the relative gain obtainable through improvement of stage mass fraction, future propulsion concepts, effect of ultrahigh chamber-pressure increases, and relative gains obtainable through improved mass fraction.

  16. EM localization for resonance frequency of pre-Cantor bar of higher stages

    NASA Astrophysics Data System (ADS)

    Kaino, K.; Obata, T.; Sonoda, J.; Kojo, J.

    2013-02-01

    Using the transmission-line theory, we investigate properties of wave propagation and resonance in a pre-Cantor multilayer called pre-Cantor bars whose interval is [0,L]. When the stage number n increases, the pre-Cantor bar will not transmit almost anywhere for ɛr2 > 1 where ɛr2 is the ratio of dielectric constants of two kinds of layers. For resonance frequencies of the n-th pre-Cantor bar, the largest amplitude of voltage at the midpoint of the bar, V(L/2), increases double-exponentially because of the inequality |V(L/2)|≤ɛr22n-2. For such a resonance frequency, the amplitude of the voltage at the midpoint of an interval [L/3k+1,2L/3k+1] is given by |V(L/2ṡ3k)|≤ɛr22n-k-2 where k = 1,2, ..., n - 1. Because the voltage |V(x)| is localized around x = L/2, the electro-magnetic wave (EM) localization occurs for the resonance frequencies of the pre-Cantor bar of the higher stages. Using a microstripline of the 3rd stage Cantor structure we will show that the measured transmission spectrum is consistent with the ideal one if the dissipation factor of the substrate is tan δ = 0.023 that is a typical value for the substrate of glassy epoxy resin in microwave frequencies.

  17. Pancreatic Cancer Stage 2B

    MedlinePlus

    ... 2B Description: Stage IIB pancreatic cancer; drawing shows cancer in the pancreas and in nearby lymph nodes. Also shown are the bile duct, pancreatic duct, and duodenum. Stage IIB pancreatic cancer. Cancer has spread to nearby lymph nodes and ...

  18. Pancreatic Cancer Stage 2A

    MedlinePlus

    ... 2A Description: Stage IIA pancreatic cancer; drawing shows cancer in the pancreas and duodenum. The bile duct and pancreatic duct are also shown. Stage IIA pancreatic cancer. Cancer has spread to nearby tissue and organs ...

  19. PREDICTING TURBINE STAGE PERFORMANCE

    NASA Technical Reports Server (NTRS)

    Boyle, R. J.

    1994-01-01

    This program was developed to predict turbine stage performance taking into account the effects of complex passage geometries. The method uses a quasi-3D inviscid-flow analysis iteratively coupled to calculated losses so that changes in losses result in changes in the flow distribution. In this manner the effects of both the geometry on the flow distribution and the flow distribution on losses are accounted for. The flow may be subsonic or shock-free transonic. The blade row may be fixed or rotating, and the blades may be twisted and leaned. This program has been applied to axial and radial turbines, and is helpful in the analysis of mixed flow machines. This program is a combination of the flow analysis programs MERIDL and TSONIC coupled to the boundary layer program BLAYER. The subsonic flow solution is obtained by a finite difference, stream function analysis. Transonic blade-to-blade solutions are obtained using information from the finite difference, stream function solution with a reduced flow factor. Upstream and downstream flow variables may vary from hub to shroud and provision is made to correct for loss of stagnation pressure. Boundary layer analyses are made to determine profile and end-wall friction losses. Empirical loss models are used to account for incidence, secondary flow, disc windage, and clearance losses. The total losses are then used to calculate stator, rotor, and stage efficiency. This program is written in FORTRAN IV for batch execution and has been implemented on an IBM 370/3033 under TSS with a central memory requirement of approximately 4.5 Megs of 8 bit bytes. This program was developed in 1985.

  20. Staged urethroplasty: indications and techniques.

    PubMed

    Secrest, Charles L

    2002-05-01

    There is still a place for staged urethroplasty. There are some indications for staged urethral reconstruction such as strictures associated with chronic inflammation, fistula, false passage, urethral stones, urethral diverticula, abscess, failed prior repair, complicated hypospadias, severe trauma, neurologic diseases, extensive BXO strictures and long strictures. Staging a urethroplasty should not be considered a step backwards rather instead we should learn from experience and realize there are some patients who are too complex to reconstruct in a single stage. PMID:12371236

  1. Ares First Stage Element Status

    NASA Technical Reports Server (NTRS)

    Tiller, Bruce K.

    2009-01-01

    This slide presentation summarizes the status of the various elements of the first stage of the Ares I vehicle. It includes views of the first stage in relation to the complete Ares rocket, details of the first stage, upgrades for the Ares, the Avionics system, and the thrust oscillation system. There are also pictures from the testing.

  2. Ares I First Stage Progress

    NASA Technical Reports Server (NTRS)

    Brasfield, Fred

    2009-01-01

    Building on the legacy of the Space Shuttle and other NASA space exploration initiatives, the propulsion for the Ares I First Stage will be a Shuttle derived reusable solid rocket motor. Significant progress has been made to date by the Ares First Stage Team. This brief status provides an update on the design and development of the Ares First Stage propulsion system.

  3. Stage Acquisition and Stage Use. An Appraisal of Stage Displacement Explanations of Variation in Moral Reasoning.

    ERIC Educational Resources Information Center

    Levine, Charles G.

    1979-01-01

    Evaluates the differing perspectives of Kohlberg and Turiel on moral reasoning. Both perspectives use stage displacement models to depict moral development and assume that as ontogenesis proceeds, the role played by earleir acquired moral stages becomes increasingly insignificant in comparison with the role played by more advanced stages. The…

  4. [Stage 1 testicular seminoma].

    PubMed

    Gross, E; Champetier, C; Pointreau, Y; Zaccariotto, A; Dubergé, T; Chauvet, B

    2010-11-01

    Testicular cancer is rare, representing only 1 % of malignant tumors, but the most common cancer in young men, 15 to 35 years. Adjuvant radiotherapy after orchidectomy in testicular seminoma stage I, reduces risk of relapse. It aims to eradicate micro-metastatic disease in lymph drainage territories. In the case of adjuvant radiotherapy, the relapse-free survival of 96 % with an overall survival of 98 % at 5 years. The irradiation volume is made up of lymph nodes paraaortic which it is possible to add the ipsilateral renal hilum to the testicular lesion. The current recommended dose is 20 Gy in 10 fractions and 2 weeks, usually delivered by two antero-posterior beams. The acute toxicities, mainly represented by nausea and diarrhea are usually quickly resolved to the end of irradiation. Regarding toxicities long-term, preservation of semen should be considered after surgery because of fear of infertility post-treatment. The risk of second cancer associated with exposure to ionizing radiation, albeit small, is especially important to consider these patients to significant life expectancy. Nevertheless, developments in radiotherapy techniques and lower doses and irradiated volumes can probably reduce this risk further. PMID:21129662

  5. Oblimersen Sodium and Combination Chemotherapy in Treating Patients With Newly Diagnosed Stage I, Stage II, Stage III, or Stage IV Diffuse Large B-Cell Lymphoma

    ClinicalTrials.gov

    2012-10-11

    Contiguous Stage II Adult Diffuse Large Cell Lymphoma; Noncontiguous Stage II Adult Diffuse Large Cell Lymphoma; Stage I Adult Diffuse Large Cell Lymphoma; Stage III Adult Diffuse Large Cell Lymphoma; Stage IV Adult Diffuse Large Cell Lymphoma

  6. Bevacizumab, Cisplatin, Radiation Therapy, and Fluorouracil in Treating Patients With Stage IIB, Stage III, Stage IVA, or Stage IVB Nasopharyngeal Cancer

    ClinicalTrials.gov

    2014-04-21

    Stage II Squamous Cell Carcinoma of the Nasopharynx; Stage III Lymphoepithelioma of the Nasopharynx; Stage III Squamous Cell Carcinoma of the Nasopharynx; Stage IV Lymphoepithelioma of the Nasopharynx; Stage IV Squamous Cell Carcinoma of the Nasopharynx

  7. Advanced two-stage compressor program design of inlet stage

    NASA Technical Reports Server (NTRS)

    Bryce, C. A.; Paine, C. J.; Mccutcheon, A. R. S.; Tu, R. K.; Perrone, G. L.

    1973-01-01

    The aerodynamic design of an inlet stage for a two-stage, 10/1 pressure ratio, 2 lb/sec flow rate compressor is discussed. Initially a performance comparison was conducted for an axial, mixed flow and centrifugal second stage. A modified mixed flow configuration with tandem rotors and tandem stators was selected for the inlet stage. The term conical flow compressor was coined to describe a particular type of mixed flow compressor configuration which utilizes axial flow type blading and an increase in radius to increase the work input potential. Design details of the conical flow compressor are described.

  8. Which Stage of ADPKD Is More Appropriate for Decortication? A Retrospective Study of 137 Patients from a Single Clinic

    PubMed Central

    Li, Ruipeng; Liu, Hailong; Kong, Xiangjie; Duan, Liujian; Qi, Jun

    2015-01-01

    Objective To study retrospectively the efficacy of decortication in patients with different stages of ADPKD and to determine which stage for decortication is more appropriate. Materials and Methods We analyzed 137 patients with ADPKD from 2001 to 2010. All patients were divided into three stages. A total of 70 patients underwent decortication, and we studied intraoperative indicators and postoperative indicators at 1 and 3 years follow-up. Results In 70 patients who underwent decortication, significant differences were observed in operative duration and bleeding volume between patients with stage I and II ADPKD (P<0.05), but no significant differences were observed in intestinal recovery time, pain medication dose, and the days of postoperative hospitalization (P > 0.05). The total complication occurrence rate was significantly different between them (P < 0.05). The serum creatinine (Scr) levels in patients with stage I ADPKD were within normal limits 1 and 3 years postoperatively and did not differ significantly (P > 0.05). Scr levels were significantly decreased in patients with stage II ADPKD in the 1st postoperative year (P < 0.05), but these were not significant differences in the 3rd postoperative year (P > 0.05). In the 1st postoperative year, VAS value, blood pressure and renal volume significantly differed (P < 0.05). However, no significant differences were observed 3 years later (P > 0.05). Conclusions Decortication in patients with stage I ADPKD can alleviate back pain symptoms and decrease blood pressure within 1 year, but the long-term efficacy is not ideal. Scr levels can be maintained within normal limits, suggesting that decortication does not lead to deterioration of renal function. For patients with stage II ADPKD, decortication can significantly improve renal function over the short term. However, after 3 years, renal function returns to the preoperative level, and surgical difficulties and complications also increase. PMID:25939015

  9. Multi-stage complex contagions.

    PubMed

    Melnik, Sergey; Ward, Jonathan A; Gleeson, James P; Porter, Mason A

    2013-03-01

    The spread of ideas across a social network can be studied using complex contagion models, in which agents are activated by contact with multiple activated neighbors. The investigation of complex contagions can provide crucial insights into social influence and behavior-adoption cascades on networks. In this paper, we introduce a model of a multi-stage complex contagion on networks. Agents at different stages-which could, for example, represent differing levels of support for a social movement or differing levels of commitment to a certain product or idea-exert different amounts of influence on their neighbors. We demonstrate that the presence of even one additional stage introduces novel dynamical behavior, including interplay between multiple cascades, which cannot occur in single-stage contagion models. We find that cascades-and hence collective action-can be driven not only by high-stage influencers but also by low-stage influencers. PMID:23556961

  10. Staged membrane oxidation reactor system

    DOEpatents

    Repasky, John Michael; Carolan, Michael Francis; Stein, VanEric Edward; Chen, Christopher Ming-Poh

    2014-05-20

    Ion transport membrane oxidation system comprising (a) two or more membrane oxidation stages, each stage comprising a reactant zone, an oxidant zone, one or more ion transport membranes separating the reactant zone from the oxidant zone, a reactant gas inlet region, a reactant gas outlet region, an oxidant gas inlet region, and an oxidant gas outlet region; (b) an interstage reactant gas flow path disposed between each pair of membrane oxidation stages and adapted to place the reactant gas outlet region of a first stage of the pair in flow communication with the reactant gas inlet region of a second stage of the pair; and (c) one or more reactant interstage feed gas lines, each line being in flow communication with any interstage reactant gas flow path or with the reactant zone of any membrane oxidation stage receiving interstage reactant gas.

  11. Staged membrane oxidation reactor system

    DOEpatents

    Repasky, John Michael; Carolan, Michael Francis; Stein, VanEric Edward; Chen, Christopher Ming-Poh

    2013-04-16

    Ion transport membrane oxidation system comprising (a) two or more membrane oxidation stages, each stage comprising a reactant zone, an oxidant zone, one or more ion transport membranes separating the reactant zone from the oxidant zone, a reactant gas inlet region, a reactant gas outlet region, an oxidant gas inlet region, and an oxidant gas outlet region; (b) an interstage reactant gas flow path disposed between each pair of membrane oxidation stages and adapted to place the reactant gas outlet region of a first stage of the pair in flow communication with the reactant gas inlet region of a second stage of the pair; and (c) one or more reactant interstage feed gas lines, each line being in flow communication with any interstage reactant gas flow path or with the reactant zone of any membrane oxidation stage receiving interstage reactant gas.

  12. Staged membrane oxidation reactor system

    DOEpatents

    Repasky, John Michael; Carolan, Michael Francis; Stein, VanEric Edward; Chen, Christopher Ming-Poh

    2012-09-11

    Ion transport membrane oxidation system comprising (a) two or more membrane oxidation stages, each stage comprising a reactant zone, an oxidant zone, one or more ion transport membranes separating the reactant zone from the oxidant zone, a reactant gas inlet region, a reactant gas outlet region, an oxidant gas inlet region, and an oxidant gas outlet region; (b) an interstage reactant gas flow path disposed between each pair of membrane oxidation stages and adapted to place the reactant gas outlet region of a first stage of the pair in flow communication with the reactant gas inlet region of a second stage of the pair; and (c) one or more reactant interstage feed gas lines, each line being in flow communication with any interstage reactant gas flow path or with the reactant zone of any membrane oxidation stage receiving interstage reactant gas.

  13. Staged Repository Development Programmes

    SciTech Connect

    Isaacs, T

    2003-10-01

    Programs to manage and ultimately dispose of high-level radioactive wastes are unique from scientific and technological as well as socio-political aspects. From a scientific and technological perspective, high-level radioactive wastes remain potentially hazardous for geological time periods-many millennia-and scientific and technological programs must be put in place that result in a system that provides high confidence that the wastes will be isolated from the accessible environment for these many thousands of years. Of course, ''proof'' in the classical sense is not possible at the outset, since the performance of the system can only be known with assurance, if ever, after the waste has been emplaced for those geological time periods. Adding to this challenge, many uncertainties exist in both the natural and engineered systems that are intended to isolate the wastes, and some of the uncertainties will remain regardless of the time and expense in attempting to characterize the system and assess its performance. What was perhaps underappreciated in the early days of waste management and repository program development were the unique and intense reactions that the institutional, political, and public bodies would have to repository program development, particularly in programs attempting to identify and then select sites for characterization, design, licensing, and ultimate development. Reactions in most nations were strong, focused, unrelenting, and often successful in hindering, derailing, and even stopping national repository programs. The reasons for such reactions and the measures to successfully respond to them are still evolving and continue to be the focus of many national program and political leaders. Adaptive Staging suggests an approach to repository program development that reflects the unique challenges associated with the disposal of high-level radioactive waste. The step-wise, incremental, learn-as-you-go approach is intended to maximize the

  14. Ares I Upper Stage Element

    NASA Technical Reports Server (NTRS)

    Chojnacki, Kent

    2009-01-01

    This slide presentation reviews the elements that make up the Ares I launch vehicle, with particular attention devoted to the upper stage of the vehicle. The upper stage elememnts, a lunar mission profile, and the upper stage objectives are reviewed. The work that Marshall Space Flight Center is doing is highlighted: work on the full scale welding process, the vertical milling machining, and the thermal protection system.

  15. Staging of neoplasms. Volume 7

    SciTech Connect

    Glazer, G.M.

    1986-01-01

    This book is divided into ten chapters. The first, an overview of the importance of staging, is followed by separate chapters on computed tomographic (CT) evaluation of lymph node metastases; metastatic disease to the thorax; staging of laryngeal, hypopharyngeal, esophageal, non-small cell lung, and renal carcinoma; and pediatric abdominal malignancies. CT staging of lymphomas is dealt with in a separate chapter. The final chapter summarizes initial experiences with staging of neoplasms by magnetic resonance (MR) imaging. Other neoplasms, such as pelvic, pancreatic, and gastrointestinal, are not discussed in depth. The book concludes with ten case studies, most of which deal with pelvic and gastrointestinal malignancies.

  16. Carboplatin and Paclitaxel With or Without Cisplatin and Radiation Therapy in Treating Patients With Stage I, Stage II, Stage III, or Stage IVA Endometrial Cancer

    ClinicalTrials.gov

    2016-02-09

    Endometrial Clear Cell Adenocarcinoma; Endometrial Serous Adenocarcinoma; Stage IA Uterine Corpus Cancer; Stage IB Uterine Corpus Cancer; Stage II Uterine Corpus Cancer; Stage IIIA Uterine Corpus Cancer; Stage IIIB Uterine Corpus Cancer; Stage IIIC Uterine Corpus Cancer; Stage IVA Uterine Corpus Cancer

  17. Second stage gasifier in staged gasification and integrated process

    DOEpatents

    Liu, Guohai; Vimalchand, Pannalal; Peng, Wan Wang

    2015-10-06

    A second stage gasification unit in a staged gasification integrated process flow scheme and operating methods are disclosed to gasify a wide range of low reactivity fuels. The inclusion of second stage gasification unit operating at high temperatures closer to ash fusion temperatures in the bed provides sufficient flexibility in unit configurations, operating conditions and methods to achieve an overall carbon conversion of over 95% for low reactivity materials such as bituminous and anthracite coals, petroleum residues and coke. The second stage gasification unit includes a stationary fluidized bed gasifier operating with a sufficiently turbulent bed of predefined inert bed material with lean char carbon content. The second stage gasifier fluidized bed is operated at relatively high temperatures up to 1400.degree. C. Steam and oxidant mixture can be injected to further increase the freeboard region operating temperature in the range of approximately from 50 to 100.degree. C. above the bed temperature.

  18. A Model of Moral Stages

    ERIC Educational Resources Information Center

    Reed, Don Collins

    2008-01-01

    The argument of this paper focuses on the relationship between cognitive structures and structures of interaction. It contends that there is still a place in moral development theory and research for a concept of moral stages. The thesis, in short, is that moral stages are not structures of thought. They are structures of action encoded in…

  19. Multiple stage miniature stepping motor

    DOEpatents

    Niven, William A.; Shikany, S. David; Shira, Michael L.

    1981-01-01

    A stepping motor comprising a plurality of stages which may be selectively activated to effect stepping movement of the motor, and which are mounted along a common rotor shaft to achieve considerable reduction in motor size and minimum diameter, whereby sequential activation of the stages results in successive rotor steps with direction being determined by the particular activating sequence followed.

  20. Lung Cancer Staging and Prognosis.

    PubMed

    Woodard, Gavitt A; Jones, Kirk D; Jablons, David M

    2016-01-01

    The seventh edition of the non-small cell lung cancer (NSCLC) TNM staging system was developed by the International Association for the Staging of Lung Cancer (IASLC) Lung Cancer Staging Project by a coordinated international effort to develop data-derived TNM classifications with significant survival differences. Based on these TNM groupings, current 5-year survival estimates in NSLCC range from 73 % in stage IA disease to 13 % in stage IV disease. TNM stage remains the most important prognostic factor in predicting recurrence rates and survival times, followed by tumor histologic grade, and patient sex, age, and performance status. Molecular prognostication in lung cancer is an exploding area of research where interest has moved beyond TNM stage and into individualized genetic tumor analysis with immunohistochemistry, microarray, and mutation profiles. However, despite intense research efforts and countless publications, no molecular prognostic marker has been adopted into clinical use since most fail in subsequent cross-validation with few exceptions. The recent interest in immunotherapy for NSCLC has identified new biomarkers with early evidence that suggests that PD-L1 is a predictive marker of a good response to new immunotherapy drugs but a poor prognostic indicator of overall survival. Future prognostication of outcomes in NSCLC will likely be based on a combination of TNM stage and molecular tumor profiling and yield more precise, individualized survival estimates and treatment algorithms. PMID:27535389

  1. Lernpunkt Deutsch--Stage 1.

    ERIC Educational Resources Information Center

    Theil, Elvira

    1997-01-01

    Evaluates the first stage of "Lernpunkt Deutsch," a new three-stage German course designed for upper elementary and early secondary school. Describes the publisher's package of materials and the appropriateness of the course, utility of the different package elements, format of the materials, and assesses whether the course provides pedagogically…

  2. Ares I Upper Stage Overview

    NASA Technical Reports Server (NTRS)

    Verhage, Marc

    2007-01-01

    The Upper Stage Element of NASA's Ares I Crew Launch Vehicle (CLV) is a "clean-sheet" approach that is being designed and developed in-house, with Element management at MSFC. The Upper Stage Element concept is a self-supporting cylindrical structure, approximately 84' long and 18' in diameter. While the First Stage Solid Rocket Booster (SRB) design has changed since the CLV inception, the Upper Stage Element design has remained essentially a clean-sheet design approach. A clean-sheet upper stage design does offer many advantages: a design for increased reliability; built-in evolvability to allow for commonality/growth without major redesign; incorporation of state-of-the-art materials and hardware; and incorporation of design, fabrication, and test techniques and processes to facilitate a more operable system.

  3. Multi-stage complex contagions

    NASA Astrophysics Data System (ADS)

    Melnik, Sergey; Ward, Jonathan A.; Gleeson, James P.; Porter, Mason A.

    2013-03-01

    The spread of ideas across a social network can be studied using complex contagion models, in which agents are activated by contact with multiple activated neighbors. The investigation of complex contagions can provide crucial insights into social influence and behavior-adoption cascades on networks. In this paper, we introduce a model of a multi-stage complex contagion on networks. Agents at different stages—which could, for example, represent differing levels of support for a social movement or differing levels of commitment to a certain product or idea—exert different amounts of influence on their neighbors. We demonstrate that the presence of even one additional stage introduces novel dynamical behavior, including interplay between multiple cascades, which cannot occur in single-stage contagion models. We find that cascades—and hence collective action—can be driven not only by high-stage influencers but also by low-stage influencers.

  4. Subminiature infrared detector translation stage

    NASA Technical Reports Server (NTRS)

    Bell, Alan D.

    1989-01-01

    This paper describes a precision subminiature three-axis translation stage used in the GOES Sounder to provide positional adjustment of 12 cooled infrared detectors. Four separate translation stages and detectors are packaged into a detector mechanism which has an overall size of 0.850 x 1.230 x 0.600 inches. Each translation stage is capable of + or - 0.015 inch motion in the X and Y axes and +0.050/-0.025 inch motion in the Z axis with a sensitivity of 0.0002 inches. The function of the detector translation stage allows real time detector signal peaking during Sounder alignment. The translation stage operates in a cryogenic environment under a 10 to the -6th torr vacuum.

  5. Stage measurement at gaging stations

    USGS Publications Warehouse

    Sauer, Vernon B.; Turnipseed, D. Phil

    2010-01-01

    Stream and reservoir stage are critical parameters in the computation of stream discharge and reservoir volume, respectively. In addition, a record of stream stage is useful in the design of structures that may be affected by stream elevation, as well as for the planning for various uses of flood plains. This report describes equipment and methodology for the observation, sensing, and recording of stage in streams and reservoirs. Although the U.S. Geological Survey (USGS) still uses the traditional, basic stilling-well float system as a predominant gaging station, modern electronic stage sensors and water-level recorders are now commonly used. Bubble gages coupled with nonsubmersible pressure transducers eliminate the need for stilling wells. Submersible pressure transducers have become common in use for the measurement of stage in both rivers and lakes. Furthermore, noncontact methods, such as radar, acoustic, and laser methods of sensing water levels, are being developed and tested, and in the case of radar, are commonly used for the measurement of stage. This report describes commonly used gaging-station structures, as well as the design and operation of gaging stations. Almost all of the equipment and instruments described in this report will meet the accuracy standard set by the USGS Office of Surface Water (OSW) for the measurement of stage for most applications, which is ?0.01 foot (ft) or 0.2 percent of the effective stage. Several telemetry systems are used to transmit stage data from the gaging station to the office, although satellite telemetry has become the standard. These telemetry systems provide near real-time stage data, as well as other information that alerts the hydrographer to extreme or abnormal events, and instrument malfunctions.

  6. Cognitive Development and Group Stages.

    ERIC Educational Resources Information Center

    Saidla, Debie D.

    1990-01-01

    Attempts to integrate Perry's (1970) scheme of the cognitive development of college students with a model of group development adapted by Waldo (1985) based on Tuckman's (1965) formulation of developmental group stages. (Author)

  7. Two stage liquefaction of coal

    DOEpatents

    Neuworth, Martin B.

    1981-01-01

    A two stage coal liquefaction process and apparatus comprising hydrogen donor solvent extracting, solvent deashing, and catalytic hydrocracking. Preferrably, the catalytic hydrocracking is performed in an ebullating bed hydrocracker.

  8. Neuroblastoma: diagnostic imaging and staging

    SciTech Connect

    Stark, D.D.; Moss, A.A.; Brasch, R.C.; deLorimier, A.A.; Albin, A.R.; London, D.A.; Gooding, C.A.

    1983-07-01

    Results of computed tomography (CT), scintigraphy, excretory urography, and other imaging tests used to diagnose and stage 38 cases of neuroblastoma prior to treatment were reviewed. Findings of these examinations were correlated with clinical data, laboratory data, results of biopsy, and surgical findings. CT was the most sensitive single test (100%) for the detection and delineation of the primary tumor. Calcifications that suggested the histologic diagnosis of neuroblastoma were present in 79% of the cases. Rim calcifications, the most specific pattern for neuroblastoma, were identified in 29% of all cases. CT alone accurately staged 82% of cases; when complemented by bone marrow biopsy, staging accuracy was 97%. CT alone was more accurate than any combination of imaging tests that excluded CT. An algorithm using CT is presented for the diagnosis and staging of neuroblastoma at reduced cost and with increased efficiency.

  9. Two stage to orbit design

    NASA Technical Reports Server (NTRS)

    1991-01-01

    A preliminary design of a two-stage to orbit vehicle was conducted with the requirements to carry a 10,000 pound payload into a 300 mile low-earth orbit using an airbreathing first stage, and to take off and land unassisted on a 15,000 foot runway. The goal of the design analysis was to produce the most efficient vehicle in size and weight which could accomplish the mission requirements. Initial parametric analysis indicated that the weight of the orbiter and the transonic performance of the system were the two parameters that had the largest impact on the design. The resulting system uses a turbofan ramjet powered first stage to propel a scramjet and rocket powered orbiter to the stage point of Mach 6 to 6.5 at an altitude of 90,000 ft.

  10. Evaluating the Stage Learning Hypothesis.

    ERIC Educational Resources Information Center

    Thomas, Hoben

    1980-01-01

    A procedure for evaluating the Genevan stage learning hypothesis is illustrated by analyzing Inhelder, Sinclair, and Bovet's guided learning experiments (in "Learning and the Development of Cognition." Cambridge: Harvard University Press, 1974). (Author/MP)

  11. Rehabilitation using single stage implants

    PubMed Central

    Mohamed, Jumshad B.; Sudarsan, Sabitha; Arun, K. V.; Shivakumar, B.

    2009-01-01

    Implant related prosthesis has become an integral part of rehabilitation of edentulous areas. Single stage implant placement has become popular because of its ease of use and fairly predictable results. In this paper, we present a series of cases of single stage implants being used to rehabilitate different clinical situations. All the implants placed have been successfully restored and followed up for up to one year. PMID:20376239

  12. Antemortem Prediction of Braak Stage.

    PubMed

    Carlson, Jesper O E; Gatz, Margaret; Pedersen, Nancy L; Graff, Caroline; Nennesmo, Inger; Lindström, Anna-Karin; Gerritsen, Lotte

    2015-11-01

    We examined the extent to which tauopathy distribution, as determined by Braak staging, might be predicted by various risk factors in older individuals. The Swedish Twin Registry provided extensive information on neuropsychological function, lifestyle, and cardiovascular risk factors of 128 patients for whom autopsy data including Braak staging were available. Logistic regression was used to develop a prognostic model that targeted discrimination between Braak stages 0 to II and III to VI. The analysis showed that Braak stages III to VI were significantly predicted by having 1 or more APOE ε4 alleles, older age, high total cholesterol, absence of diabetes and cardiovascular disease, and poorer scores on the Wechsler Adult Intelligence Score Information test, verbal fluency, and recognition memory but better verbal recall. The algorithm predicted Braak stages III to VI well (receiver-operating characteristic area under curve, 0.897; 95% confidence interval, 0.842-0.951). Using a cutoff of 50% risk or more, the sensitivity was 85%, the specificity was 70%, and the negative predictive value was 69%. This study demonstrates that tauopathy distribution can be accurately predicted using a combination of antemortem patient data. These results provide further insight into tauopathy development and AD-related disease mechanisms and suggest a prognostic model that predicts the spread of neurofibrillary tangles above the transentorhinal stage. PMID:26469248

  13. Staged regenerative sorption heat pump

    NASA Technical Reports Server (NTRS)

    Jones, Jack A. (Inventor)

    1995-01-01

    A regenerative adsorbent heat pump process and system for cooling and heating a space. A sorbent is confined in a plurality of compressors of which at least four are first stage and at least four are second stage. The first stage operates over a first pressure region and the second stage over a second pressure region which is higher than the first. Sorbate from the first stage enters the second stage. The sorbate loop includes a condenser, expansion valve, evaporator and the compressors. A single sorbate loop can be employed for single-temperature-control such as air conditioning and heating. Two sorbate loops can be used for two-temperature-control as in a refrigerator and freezer. The evaporator temperatures control the freezer and refrigerator temperatures. Alternatively the refrigerator temperature can be cooled by the freezer with one sorbate loop. A heat transfer fluid is circulated in a closed loop which includes a radiator and the compressors. Low temperature heat is exhausted by the radiator. High temperature heat is added to the heat transfer fluid entering the compressors which are desorbing vapor. Heat is transferred from compressors which are sorbing vapor to the heat transfer fluid, and from the heat transfer fluid to the compressors which are desorbing vapor. Each compressor is subjected to the following phases, heating to its highest temperature, cooling down from its highest temperature, cooling to its lowest temperature, and warming up from its lowest temperature. The phases are repeated to complete a cycle and regenerate heat.

  14. Crew Launch Vehicle Upper Stage

    NASA Technical Reports Server (NTRS)

    Davis, D. J.; Cook, J. R.

    2006-01-01

    The Agency s Crew Launch Vehicle (CLV) will be the first human rated space transportation system developed in the United States since the Space Shuttle. The CLV will utilize existing Shuttle heritage hardware and systems combined with a "clean sheet design" for the Upper Stage. The Upper Stage element will be designed and developed by a team of NASA engineers managed by the Marshall Space Flight Center (MSFC) in Huntsville, Alabama. The team will design the Upper Stage based on the Exploration Systems Architecture Study (ESAS) Team s point of departure conceptual design as illustrated in the figure below. This concept is a self-supporting cylindrical structure, approximately 1 15 feet long and 216 inches in diameter. While this "clean-sheet" upper stage design inherently carries more risk than utilizing a modified design, the approach also has many advantages. This paper will discuss the advantages and disadvantages of pursuing a "clean-sheet" design for the new CLV Upper Stage as well as describe in detail the overall design of the Upper Stage and its integration into NASA s CLV.

  15. Effects of temperature and host stage on the parasitization rate and offspring sex ratio of Aenasius bambawalei Hayat in Phenacoccus solenopsis Tinsley

    PubMed Central

    Zhang, Juan; Xia, Tianfeng

    2016-01-01

    Temperature and host stage are important factors that determine the successful development of parasitoids. Aenasius bambawalei Hayat (Hymenoptera: Encyrtidae) is a primary parasitoid of the newly invasive mealybug, Phenacoccus solenopsis Tinsley (Hemiptera: Pseudococcidae). The effects of temperature on the parasitic characteristics of A. bambawalei have seldom been investigated. In the study, we explored the effects of temperature, exposure time, and host stage on the parasitization rate and offspring sex ratio (female to male) of A. bambawalei under laboratory conditions. The laboratory results showed that the successful parasitization rate of A. bambawalei increased with higher temperatures and older host stages. When the parasitoids were exposed to 36 °C for 24 h, the parasitization rate of female adults (52%) was nearly two times that of 3rd instar nymphs. Additionally, heat stress duration and host stage resulted in an increase in the offspring sex ratio of A. bambawalei. When A. bambawalei was exposed to 36 °C for 24 h, the offspring sex ratio increased dramatically to 81.78% compared with those exposed for 12 h, and it increased to 45.34% compared with those exposed for 16 h. The offspring sex ratio was clearly higher when the host stage was an adult female mealybug Our findings provide important guidance for the mass rearing and field releases of A. bambawalei for the management of P. solenopsis in the future. PMID:26788437

  16. Staging or upper stage reignition for GEO missions

    NASA Astrophysics Data System (ADS)

    Duret, François

    2002-07-01

    Geostationary orbit will remain in the near and far future one of the most frequently used for several applications including, mainly, telecommunications. For the time being the GEO satcoms are injected by intermediate, heavy or super heavy class launch vehicles, LV, using quasi standard procedures: low altitude injection on a geostationary transfer orbit, ballistic phase of at least five and a half hour, followed by an apogee manoeuvre (or boost) to reach GEO. Apogee boost is most of the time provided by the propulsive system of the satellite, if this one uses liquid propellant in an integrated system performing final injection and house-keeping for the whole life (up to 15 years) of the satellite. The current launch vehicle features generally a cryogenic (LOX/LH2) or semi-cryogenic (LOX/Kerosene) upper stage having a better Isp than the Isp of the satellite propulsive system: The possibility to provide the apogee boost by the LV upper stage seems attractive. Another possibility is to put on the top of the upper stage an other small stage, or module having the function of kick-stage, as it was done earlier when solid propellant stages were used for this apogee manoeuvre. This presentation will describe the pros and cons of this various choices for single but also dual launches in GTO/GEO, and also will address future new injection scheme, providing new transportation services to satellites featuring advanced propulsive systems such as electric, plasmic or thermo-solar thrusters, requiring other transfer orbits like MEO, GTO+ and super GTO+.

  17. Two-Stage Centrifugal Fan

    NASA Technical Reports Server (NTRS)

    Converse, David

    2011-01-01

    Fan designs are often constrained by envelope, rotational speed, weight, and power. Aerodynamic performance and motor electrical performance are heavily influenced by rotational speed. The fan used in this work is at a practical limit for rotational speed due to motor performance characteristics, and there is no more space available in the packaging for a larger fan. The pressure rise requirements keep growing. The way to ordinarily accommodate a higher DP is to spin faster or grow the fan rotor diameter. The invention is to put two radially oriented stages on a single disk. Flow enters the first stage from the center; energy is imparted to the flow in the first stage blades, the flow is redirected some amount opposite to the direction of rotation in the fixed stators, and more energy is imparted to the flow in the second- stage blades. Without increasing either rotational speed or disk diameter, it is believed that as much as 50 percent more DP can be achieved with this design than with an ordinary, single-stage centrifugal design. This invention is useful primarily for fans having relatively low flow rates with relatively high pressure rise requirements.

  18. Stage Separation Performance Analysis Project

    NASA Technical Reports Server (NTRS)

    Chen, Yen-Sen; Zhang, Sijun; Liu, Jiwen; Wang, Ten-See

    2001-01-01

    Stage separation process is an important phenomenon in multi-stage launch vehicle operation. The transient flowfield coupled with the multi-body systems is a challenging problem in design analysis. The thermodynamics environment with burning propellants during the upper-stage engine start in the separation processes adds to the complexity of the-entire system. Understanding the underlying flow physics and vehicle dynamics during stage separation is required in designing a multi-stage launch vehicle with good flight performance. A computational fluid dynamics model with the capability to coupling transient multi-body dynamics systems will be a useful tool for simulating the effects of transient flowfield, plume/jet heating and vehicle dynamics. A computational model using generalize mesh system will be used as the basis of this development. The multi-body dynamics system will be solved, by integrating a system of six-degree-of-freedom equations of motion with high accuracy. Multi-body mesh system and their interactions will be modeled using parallel computing algorithms. Adaptive mesh refinement method will also be employed to enhance solution accuracy in the transient process.

  19. DIRECT COUPLED PROGRESSIVE STAGE PULSE COUNTER APPARATUS

    DOEpatents

    Kaufman, W.M.

    1962-08-14

    A progressive electrical pulse counter circuit was designed for the counting of a chain of input pulses of random width and/or frequency. The circuit employs an odd and even pulse input line alternately connected to a series of directly connected bistable counting stages. Each bistable stage has two d-c operative states which stage, when in its rnrtial state, prevents the next succeeding stage from changing its condition when the latter stage is pulsed. Since only altennate stages are pulsed for each incoming pulse, only one stage will change its state for each input pulse thereby providing prog essive stage by stage counting. (AEC)

  20. 40 CFR 264.554 - Staging piles.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... existing permit (for example, RAP), closure plan, or order be modified to allow me to use a staging pile? (1) To modify a permit, other than a RAP, to incorporate a staging pile or staging pile operating... under § 270.42 of this chapter. (2) To modify a RAP to incorporate a staging pile or staging...

  1. 40 CFR 264.554 - Staging piles.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... existing permit (for example, RAP), closure plan, or order be modified to allow me to use a staging pile? (1) To modify a permit, other than a RAP, to incorporate a staging pile or staging pile operating... under § 270.42 of this chapter. (2) To modify a RAP to incorporate a staging pile or staging...

  2. 40 CFR 264.554 - Staging piles.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... existing permit (for example, RAP), closure plan, or order be modified to allow me to use a staging pile? (1) To modify a permit, other than a RAP, to incorporate a staging pile or staging pile operating... under § 270.42 of this chapter. (2) To modify a RAP to incorporate a staging pile or staging...

  3. 40 CFR 264.554 - Staging piles.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... existing permit (for example, RAP), closure plan, or order be modified to allow me to use a staging pile? (1) To modify a permit, other than a RAP, to incorporate a staging pile or staging pile operating... under § 270.42 of this chapter. (2) To modify a RAP to incorporate a staging pile or staging...

  4. Staged separation of craniopagus twins.

    PubMed

    Dunaway, David; Jeelani, N U Owase

    2015-10-01

    Craniopagus twins are rare and account for up to 6% of all conjoined twins. No hospital will encounter many such twins and the opportunity to develop expertise is limited. We have dealt with 2 such sets and illustrate our approach by reference to our most recent set. We believe that detailed imaging allows precise delineation of the anatomy and facilitates detailed planning of the surgery. When venous drainage from the 2 brains is connected, we believe that staged separation is preferable as gradual alteration of hemodynamics may be safer than a single-stage procedure. PMID:26382265

  5. Effect of low dose nicotinic acid on hyperphosphatemia in patients with end stage renal disease.

    PubMed

    Zahed, N S; Zamanifar, N; Nikbakht, H

    2016-01-01

    Hyperphosphatemia is a risk factor for ectopic calcification and coronary artery diseases in end stage renal diseases (ESRD). The aim of this study was to assess the effect of low-dose nicotinic acid on hyperphosphatemia in patients with ESRD. This randomized, double-blind clinical trial was done on 70 ESRD patients with serum phosphoure ≥5.5 mg/dl. Patients were randomly divided into two equal groups (n = 35) and the intervention group received niacin 25 mg/day as the initial dose. After 4 weeks, in patients who did not respond to treatment, niacin dose was increased up to 50 mg/dl. At the end of week 8, in case there was no treatment effect, the dose was raised to 100 mg/day. The appropriate response to treatment was defined as serum phosphorous level reductions <5.5 mg/dl. The age was 50.5 ± 14.3 years and duration of dialysis 5.1 ± 5.3 months. In the niacin group, mean phosphorus level decreased from 6.7 ± 0.84 mg/dl at the end of the 1(st) month to 5.8 ± 1.0 mg/dl at the end of the 2(nd) month and to 4.4 ± 1.4 mg/dl at the end of the 3(rd) month (P = 0.004). In the placebo group, mean phosphorus level increased from 6.5 ± 1.2 mg/dl to 7.2 ± 0.91 mg/dl at the end of the 3(rd) month (P = 0.006). In the niacin group, high density lipoprotein (HDL) increased significantly from 45.00 ± 14.9 to 47.2 ± 11.6 (P = 0.009). We conclude that niacin (100 mg/day) decreased phosphorus serum level and increased HDL serum level in patients on dialysis. PMID:27512294

  6. Effect of low dose nicotinic acid on hyperphosphatemia in patients with end stage renal disease

    PubMed Central

    Zahed, N. S.; Zamanifar, N.; Nikbakht, H.

    2016-01-01

    Hyperphosphatemia is a risk factor for ectopic calcification and coronary artery diseases in end stage renal diseases (ESRD). The aim of this study was to assess the effect of low-dose nicotinic acid on hyperphosphatemia in patients with ESRD. This randomized, double-blind clinical trial was done on 70 ESRD patients with serum phosphoure ≥5.5 mg/dl. Patients were randomly divided into two equal groups (n = 35) and the intervention group received niacin 25 mg/day as the initial dose. After 4 weeks, in patients who did not respond to treatment, niacin dose was increased up to 50 mg/dl. At the end of week 8, in case there was no treatment effect, the dose was raised to 100 mg/day. The appropriate response to treatment was defined as serum phosphorous level reductions <5.5 mg/dl. The age was 50.5 ± 14.3 years and duration of dialysis 5.1 ± 5.3 months. In the niacin group, mean phosphorus level decreased from 6.7 ± 0.84 mg/dl at the end of the 1st month to 5.8 ± 1.0 mg/dl at the end of the 2nd month and to 4.4 ± 1.4 mg/dl at the end of the 3rd month (P = 0.004). In the placebo group, mean phosphorus level increased from 6.5 ± 1.2 mg/dl to 7.2 ± 0.91 mg/dl at the end of the 3rd month (P = 0.006). In the niacin group, high density lipoprotein (HDL) increased significantly from 45.00 ± 14.9 to 47.2 ± 11.6 (P = 0.009). We conclude that niacin (100 mg/day) decreased phosphorus serum level and increased HDL serum level in patients on dialysis. PMID:27512294

  7. How Is Small Intestine Adenocarcinoma Staged?

    MedlinePlus

    ... small intestine adenocarcinoma, by stage How is small intestine adenocarcinoma staged? Staging is a process that tells ... distant m etastasis (M). T categories for small intestine adenocarcinoma T categories of small intestine cancer describe ...

  8. Screening for Breast Cancer: Staging and Treatment

    MedlinePlus

    ... page please turn JavaScript on. Feature: Screening For Breast Cancer Staging and Treatment Past Issues / Summer 2014 Table of Contents Staging The extent (stage) of breast cancer needs to be determined to help choose the ...

  9. Ares I Stage Separation Test

    NASA Technical Reports Server (NTRS)

    2007-01-01

    Under the goals of the Vision for Space Exploration, Ares I is a chief component of the cost-effective space transportation infrastructure being developed by NASA's Constellation Program. This transportation system will safely and reliably carry human explorers back to the moon, and then onward to Mars and other destinations in the solar system. The Ares I effort includes multiple project element teams at NASA centers and contract organizations around the nation, and is managed by the Exploration Launch Projects Office at NASA's Marshall Space Flight Center (MFSC). ATK Launch Systems near Brigham City, Utah, is the prime contractor for the first stage booster. ATK's subcontractor, United Space Alliance of Houston, is designing, developing and testing the parachutes at its facilities at NASA's Kennedy Space Center in Florida. NASA's Johnson Space Center in Houston hosts the Constellation Program and Orion Crew Capsule Project Office and provides test instrumentation and support personnel. Together, these teams are developing vehicle hardware, evolving proven technologies, and testing components and systems. Their work builds on powerful, reliable space shuttle propulsion elements and nearly a half-century of NASA space flight experience and technological advances. Ares I is an inline, two-stage rocket configuration topped by the Crew Exploration Vehicle, its service module, and a launch abort system. In this HD video image, an Ares I x-test involves the upper stage separating from the first stage. This particular test was conducted at the NASA Langley Research Center in July 2007. (Highest resolution available)

  10. All the World's a Stage

    ERIC Educational Resources Information Center

    Stanistreet, Paul

    2011-01-01

    Open Stages is Britain's biggest amateur theatre project, a hugely ambitious scheme to bring the professional and amateur theatre worlds together. It is a learning project but, as the Royal Shakespeare Company's Ian Wainwright tells this author, it is not only the amateurs who are learning. Wainwright states that the amateur and professional…

  11. Stage 2--Information Seeking Strategies

    ERIC Educational Resources Information Center

    Elsenberg, Michael B.

    2005-01-01

    A brief overview of one Big6 stage by Mike Eisenberg, followed by articles by two exemplary Big6 teachers, Barbara Jansen and Rob Darrow, offering practical uses of the Big6 in elementary and secondary situations is presented. The two-part nature of information seeking strategies that includes brainstorming and choosing is emphasized.

  12. The Beginning Stages of Reading.

    ERIC Educational Resources Information Center

    Wilkie, Fiona, Comp.

    Noting that in the beginning stages of reading it is helpful for children to be surrounded by the written word and to be read to by adults, this article offers brief encapsulations of and responses to five articles about beginning reading and reading readiness. The five articles are as follows: (1) "Three-Year-Olds in Their Reading Corner" by…

  13. Stages of neuronal network formation

    NASA Astrophysics Data System (ADS)

    Woiterski, Lydia; Claudepierre, Thomas; Luxenhofer, Robert; Jordan, Rainer; Käs, Josef A.

    2013-02-01

    Graph theoretical approaches have become a powerful tool for investigating the architecture and dynamics of complex networks. The topology of network graphs revealed small-world properties for very different real systems among these neuronal networks. In this study, we observed the early development of mouse retinal ganglion cell (RGC) networks in vitro using time-lapse video microscopy. By means of a time-resolved graph theoretical analysis of the connectivity, shortest path length and the edge length, we were able to discover the different stages during the network formation. Starting from single cells, at the first stage neurons connected to each other ending up in a network with maximum complexity. In the further course, we observed a simplification of the network which manifested in a change of relevant network parameters such as the minimization of the path length. Moreover, we found that RGC networks self-organized as small-world networks at both stages; however, the optimization occurred only in the second stage.

  14. Multi-stage flash degaser

    DOEpatents

    Rapier, P.M.

    1980-06-26

    A multi-stage flash degaser is incorporated in an energy conversion system having a direct-contact, binary-fluid heat exchanger to remove essentially all of the noncondensable gases from geothermal brine ahead of the direct-contact binary-fluid heat exchanger in order that the heat exchanger and a turbine and condenser of the system can operate at optimal efficiency.

  15. CRYOGENIC UPPER STAGE SYSTEM SAFETY

    NASA Technical Reports Server (NTRS)

    Smith, R. Kenneth; French, James V.; LaRue, Peter F.; Taylor, James L.; Pollard, Kathy (Technical Monitor)

    2005-01-01

    NASA s Exploration Initiative will require development of many new systems or systems of systems. One specific example is that safe, affordable, and reliable upper stage systems to place cargo and crew in stable low earth orbit are urgently required. In this paper, we examine the failure history of previous upper stages with liquid oxygen (LOX)/liquid hydrogen (LH2) propulsion systems. Launch data from 1964 until midyear 2005 are analyzed and presented. This data analysis covers upper stage systems from the Ariane, Centaur, H-IIA, Saturn, and Atlas in addition to other vehicles. Upper stage propulsion system elements have the highest impact on reliability. This paper discusses failure occurrence in all aspects of the operational phases (Le., initial burn, coast, restarts, and trends in failure rates over time). In an effort to understand the likelihood of future failures in flight, we present timelines of engine system failures relevant to initial flight histories. Some evidence suggests that propulsion system failures as a result of design problems occur shortly after initial development of the propulsion system; whereas failures because of manufacturing or assembly processing errors may occur during any phase of the system builds process, This paper also explores the detectability of historical failures. Observations from this review are used to ascertain the potential for increased upper stage reliability given investments in integrated system health management. Based on a clear understanding of the failure and success history of previous efforts by multiple space hardware development groups, the paper will investigate potential improvements that can be realized through application of system safety principles.

  16. Operation of staged membrane oxidation reactor systems

    DOEpatents

    Repasky, John Michael

    2012-10-16

    A method of operating a multi-stage ion transport membrane oxidation system. The method comprises providing a multi-stage ion transport membrane oxidation system with at least a first membrane oxidation stage and a second membrane oxidation stage, operating the ion transport membrane oxidation system at operating conditions including a characteristic temperature of the first membrane oxidation stage and a characteristic temperature of the second membrane oxidation stage; and controlling the production capacity and/or the product quality by changing the characteristic temperature of the first membrane oxidation stage and/or changing the characteristic temperature of the second membrane oxidation stage.

  17. PreK-3rd: Raising the Educational Performance of English Language Learners (ELLs). PreK-3rd Policy to Action Brief. No. Six

    ERIC Educational Resources Information Center

    Russakoff, Dale

    2011-01-01

    In 1974, the United States Supreme Court ruled in "Lau v. Nichols" that 1,800 Chinese-speaking children in the San Francisco public schools were entitled to English-language instruction or other support to help them understand what was happening in their classrooms. Thirty-six years later, state and local responsibilities to public school children…

  18. EDITORIAL: Photonica 2011: 3rd International School and Conference on Photonics Photonica 2011: 3rd International School and Conference on Photonics

    NASA Astrophysics Data System (ADS)

    Petrović, Jovana; Stepić, Milutin; Hadžievski, Ljupčo

    2012-04-01

    Photonics is a rapidly growing discipline of physics that investigates properties of light and its interaction with matter and develops devices based on these properties. Due to both the fundamental and applied nature of photonics research, it pervades many branches of modern technology: quantum mechanics, material science, electronics, telecommunications, biology, medicine, material processing, etc. The borders between these subjects are being erased, generating new research areas such as silicon photonics, biophotonics and quantum photonics. Diverse branches of photonics are united in a common effort to further miniaturize photonic devices, integrate them with existing technologies and develop new technologies. The International School and Conference on Photonics—Photonica—is a biennial forum for the education of young scientists, exchanging new knowledge and ideas, and fostering collaboration between scientists working in photonic science and technology. Conference topics cover a broad range of research activities in optical materials, metamaterials and plasmonics, nonlinear optics, lasers, laser spectroscopy, biophotonics, optoelectronics, optocommunications, photonic crystals, holography, quantum optics and related topics in atomic physics. The aim of the organizers is to provide a platform for discussing new developments, concepts and future trends of various disciplines of photonics by bringing together researchers from academia, government and industrial laboratories. The educational element of Photonica—a series of tutorials and keynote talks—enables students and young researchers to better understand the fundamentals and their use on a route to applications, and informs both young and experienced scientists of new directions of research. The introductory lectures that are directly related to the state-of-the-art are followed by presentations and discussions on recent results during oral and vibrant poster presentations. This Topical Issue is dedicated to Photonica 2011 held on 29 August-2 September 2011 in Belgrade, Serbia. The conference was attended by 144 participants from 27 countries who gave 132 oral and poster presentations and 24 lectures. The accompanying papers were peer reviewed and 82 were selected for publication. We take this opportunity to gratefully acknowledge the contribution of the reviewers to the quality of this issue. The papers are grouped in accordance with the conference topics, each section opening with an invited paper. The issue begins with papers dedicated to ultra-cold atomic systems that display coherent behaviour analogous to that of light. These well-controlled atomic systems are indispensible workhorses for experiments in quantum optics, which is the topic of the next section. Holography as a concept, measurement tool and technique for fabrication of periodic photonic structures is placed accordingly between fundamental and applied photonics. It is followed by reports on various photonic devices, their modelling and nonlinear phenomena. The progress in constructing these devices largely depends on artificial (composites, metamaterials) and natural optical materials and their processing. This Topical Issue is an original snapshot of the current research in photonics and by no means an extensive survey of the field. While the making of the former has been a challenging task, the compilation of the latter would be indomitable due to the rapid advances in and diversification of photonics research. In accordance with the aims of the conference itself, we hope that the results reported in this Topical Issue of Physica Scripta will serve to inform and to spark the imagination of scientists and engineers exploring or using the principles and products of photonics.

  19. Early stage of nanocrystal growth

    SciTech Connect

    2012-01-01

    Berkeley Lab researchers at the Molecular Foundry have elucidated important mechanisms behind oriented attachment, the phenomenon that drives biomineralization and the growth of nanocrystals. This electron microscopy movie shows the early stage of nanocrystal growth. Nanoparticles make transient contact at many points and orientations until their lattices are perfectly matched. The particles then make a sudden jump-to-contact to form attached aggregates. (Movie courtesy of Jim DeYoreo)

  20. Upper-Stage Flight Experiment

    NASA Technical Reports Server (NTRS)

    Anderson, W. E.; Boxwell, R.; Crockett, D. V.; Ross, R.; Lewis, T.; McNeal, C.; Verdarame, K.

    1999-01-01

    For propulsion applications that require that the propellants are storable for long periods, have a high density impulse, and are environmentally clean and non-toxic, the best choice is a combination of high-concentration hydrogen peroxide (High Test Peroxide, or HTP) and a liquid hydrocarbon (LHC) fuel. The HTP/LHC combination is suitable for low-cost launch vehicles, space taxi and space maneuvering vehicles, and kick stages. Orbital Sciences Corporation is under contract with the NASA Marshall Space Flight Center in cooperation with the Air Force Research Lab to design, develop and demonstrate a new low-cost liquid upper stage based on HTP and JP-8. The Upper Stage Flight Experiment (USFE) focuses on key technologies necessary to demonstrate the operation of an inherently simple propulsion system with an innovative, state-of-the-art structure. Two key low-cost vehicle elements will be demonstrated - a 10,000 lbf thrust engine and an integrated composite tank structure. The suborbital flight test of the USFE is scheduled for 2001. Preceding the flight tests are two major series of ground tests at NASA Stennis Space Center and a subscale tank development program to identify compatible composite materials and to verify their compatibility over long periods of time. The ground tests include a thrust chamber development test series and an integrated stage test. This paper summarizes the results from the first phase of the thrust chamber development tests and the results to date from the tank material compatibility tests. Engine and tank configurations that meet the goals of the program are described.

  1. Ares I Upper Stage Update

    NASA Technical Reports Server (NTRS)

    Davis, Daniel J.

    2010-01-01

    These presentation slides review the progress in the development of the Ares I upper stage. The development includes development of a manufacturing and processing assembly that will reduce the time required over 100 days, development of a weld tool that is a robotic tool that is the largest welder of its kind in the United States, development of avionics and software, and development of logisitics and operations systems.

  2. Multi-stage flash degaser

    DOEpatents

    Rapier, Pascal M.

    1982-01-01

    A multi-stage flash degaser (18) is incorporated in an energy conversion system (10) having a direct-contact, binary-fluid heat exchanger to remove essentially all of the noncondensable gases from geothermal brine ahead of the direct-contact binary-fluid heat exchanger (22) in order that the heat exchanger (22) and a turbine (48) and condenser (32) of the system (10) can operate at optimal efficiency.

  3. Commercializing the transfer orbit stage

    NASA Technical Reports Server (NTRS)

    Miller, M. W.

    1984-01-01

    Key milestones necessary to establish the transfer orbit stage are examined. The selection of the project concept and synthesis of the company are described followed by an analysis venture capability support and the selection of a major aerospace company as prime contractor. A landmark agreement with NASA sanctioned the commercial TOS concept and provided the critical support necessary to raise the next round of venture capital. Project management and customer commitments are also discussed.

  4. Stages of motor skill learning.

    PubMed

    Luft, Andreas R; Buitrago, Manuel M

    2005-12-01

    Successful learning of a motor skill requires repetitive training. Once the skill is mastered, it can be remembered for a long period of time. The durable memory makes motor skill learning an interesting paradigm for the study of learning and memory mechanisms. To gain better understanding, one scientific approach is to dissect the process into stages and to study these as well as their interactions. This article covers the growing evidence that motor skill learning advances through stages, in which different storage mechanisms predominate. The acquisition phase is characterized by fast (within session) and slow learning (between sessions). For a short period following the initial training sessions, the skill is labile to interference by other skills and by protein synthesis inhibition, indicating that consolidation processes occur during rest periods between training sessions. During training as well as rest periods, activation in different brain regions changes dynamically. Evidence for stages in motor skill learning is provided by experiments using behavioral, electrophysiological, functional imaging, and cellular/molecular methods. PMID:16385137

  5. PIRO concept: Staging of sepsis

    PubMed Central

    Rathour, S; Kumar, S; Hadda, V; Bhalla, A; Sharma, N; Varma, S

    2015-01-01

    Introduction: Sepsis is common presenting illness to the emergency services and one of the leading causes of hospital mortality. Researchers and clinicians have realized that the systemic inflammatory response syndrome concept for defining sepsis is less useful and lacks specificity. The predisposition, infection (or insult), response and organ dysfunction (PIRO) staging of sepsis similar to malignant diseases (TNM staging) might give better information. Materials and Methods: A prospective observational study was conducted in emergency medical services attached to medicine department of a tertiary care hospital in Northern India. Patients with age 18 years or more with proven sepsis were included in the first 24 hours of the diagnosis. Two hundred patients were recruited. Multivariate logistic regression analysis was done to assess the factors that predicted in-hospital mortality. Results: Two hundred patients with proven sepsis, admitted to the emergency medical services were analysed. Male preponderance was noted (M: F ratio = 1.6:1). Mean age of study cohort was 50.50 ± 16.30 years. Out of 200 patients, 116 (58%) had in-hospital mortality. In multivariate logistic regression analysis, the factors independently associated with in-hospital mortality for predisposition component of PIRO staging were age >70 years, chronic obstructive pulmonary disease, chronic liver disease, cancer and presence of foley's catheter; for infection/insult were pneumonia, urinary tract infection and meningitis/encephalitis; for response variable were tachypnea (respiratory rate >20/minute) and bandemia (band >5%). Organ dysfunction variables associated with hospital mortality were systolic blood pressure <90mm Hg, prolonged activated partial thromboplastin time, raised serum creatinine, partial pressure of oxygen in arterial blood/fraction of inspired oxygen (PaO2/FiO2) ratio <300, decreased urine output in first two hours of emergency presentation and Glasgow coma scale ≤9. Each

  6. Stages of change or changes of stage? Predicting transitions in transtheoretical model stages in relation to healthy food choice.

    PubMed

    Armitage, Christopher J; Sheeran, Paschal; Conner, Mark; Arden, Madelynne A

    2004-06-01

    Relatively little research has examined factors that account for transitions between transtheoretical model (TTM) stages of change. The present study (N = 787) used sociodemographic, TTM, and theory of planned behavior (TPB) variables, as well as theory-driven interventions to predict changes in stage. Longitudinal analyses revealed that sociodemographic, TPB, and 1 of the interventions predicted transitions between most stages of change. In fact, only progression from the preparation stage was not predictable. However, given that this change of stage marks the transition between cognition and actual behavior, the identification of variables that bridge this gap is crucial for the development of interventions to promote stage transitions. PMID:15279532

  7. Ares I Upper Stage Fabrication

    NASA Technical Reports Server (NTRS)

    2006-01-01

    Under the goals of the Vision for Space Exploration, Ares I is a chief component of the cost-effective space transportation infrastructure being developed by NASA's Constellation Program. This transportation system will safely and reliably carry human explorers back to the moon, and then onward to Mars and other destinations in the solar system. The Ares I effort includes multiple project element teams at NASA centers and contract organizations around the nation, and is managed by the Exploration Launch Projects Office at NASA's Marshall Space Flight Center (MFSC). ATK Launch Systems near Brigham City, Utah, is the prime contractor for the first stage booster. ATK's subcontractor, United Space Alliance of Houston, is designing, developing and testing the parachutes at its facilities at NASA's Kennedy Space Center in Florida. NASA's Johnson Space Center in Houston hosts the Constellation Program and Orion Crew Capsule Project Office and provides test instrumentation and support personnel. Together, these teams are developing vehicle hardware, evolving proven technologies, and testing components and systems. Their work builds on powerful, reliable space shuttle propulsion elements and nearly a half-century of NASA space flight experience and technological advances. Ares I is an inline, two-stage rocket configuration topped by the Crew Exploration Vehicle, its service module, and a launch abort system. This HD video image depicts a manufactured aluminum panel, that will fabricate the Ares I upper stage barrel, undergoing a confidence panel test. In this test, bent aluminum is stressed to breaking point and thoroughly examined. The panels are manufactured by AMRO Manufacturing located in El Monte, California. (Highest resolution available)

  8. Ares I Upper Stage Fabrication

    NASA Technical Reports Server (NTRS)

    2007-01-01

    Under the goals of the Vision for Space Exploration, Ares I is a chief component of the cost-effective space transportation infrastructure being developed by NASA's Constellation Program. This transportation system will safely and reliably carry human explorers back to the moon, and then onward to Mars and other destinations in the solar system. The Ares I effort includes multiple project element teams at NASA centers and contract organizations around the nation, and is managed by the Exploration Launch Projects Office at NASA's Marshall Space Flight Center (MFSC). ATK Launch Systems near Brigham City, Utah, is the prime contractor for the first stage booster. ATK's subcontractor, United Space Alliance of Houston, is designing, developing and testing the parachutes at its facilities at NASA's Kennedy Space Center in Florida. NASA's Johnson Space Center in Houston hosts the Constellation Program and Orion Crew Capsule Project Office and provides test instrumentation and support personnel. Together, these teams are developing vehicle hardware, evolving proven technologies, and testing components and systems. Their work builds on powerful, reliable space shuttle propulsion elements and nearly a half-century of NASA space flight experience and technological advances. Ares I is an inline, two-stage rocket configuration topped by the Crew Exploration Vehicle, its service module, and a launch abort system. In this HD video image, processes for upper stage barrel fabrication are talking place. The aluminum panels are manufacturing process demonstration articles that will undergo testing until perfected. The panels are built by AMRO Manufacturing located in El Monte, California. (Highest resolution available)

  9. Ares I Upper Stage Fabrication

    NASA Technical Reports Server (NTRS)

    2007-01-01

    Under the goals of the Vision for Space Exploration, Ares I is a chief component of the cost-effective space transportation infrastructure being developed by NASA's Constellation Program. This transportation system will safely and reliably carry human explorers back to the moon, and then onward to Mars and other destinations in the solar system. The Ares I effort includes multiple project element teams at NASA centers and contract organizations around the nation, and is managed by the Exploration Launch Projects Office at NASA's Marshall Space Flight Center (MFSC). ATK Launch Systems near Brigham City, Utah, is the prime contractor for the first stage booster. ATK's subcontractor, United Space Alliance of Houston, is designing, developing and testing the parachutes at its facilities at NASA's Kennedy Space Center in Florida. NASA's Johnson Space Center in Houston hosts the Constellation Program and Orion Crew Capsule Project Office and provides test instrumentation and support personnel. Together, these teams are developing vehicle hardware, evolving proven technologies, and testing components and systems. Their work builds on powerful, reliable space shuttle propulsion elements and nearly a half-century of NASA space flight experience and technological advances. Ares I is an inline, two-stage rocket configuration topped by the Crew Exploration Vehicle, its service module, and a launch abort system. This HD video image depicts a manufactured aluminum panel that will be used to fabricate the Ares I upper stage barrel, undergoing a confidence panel test. In this test, the bent aluminum is stressed to breaking point and thoroughly examined. The panels are manufactured by AMRO Manufacturing located in El Monte, California.

  10. Ares I Upper Stage Fabrication

    NASA Technical Reports Server (NTRS)

    2006-01-01

    Under the goals of the Vision for Space Exploration, Ares I is a chief component of the cost-effective space transportation infrastructure being developed by NASA's Constellation Program. This transportation system will safely and reliably carry human explorers back to the moon, and then onward to Mars and other destinations in the solar system. The Ares I effort includes multiple project element teams at NASA centers and contract organizations around the nation, and is managed by the Exploration Launch Projects Office at NASA's Marshall Space Flight Center (MFSC). ATK Launch Systems near Brigham City, Utah, is the prime contractor for the first stage booster. ATK's subcontractor, United Space Alliance of Houston, is designing, developing and testing the parachutes at its facilities at NASA's Kennedy Space Center in Florida. NASA's Johnson Space Center in Houston hosts the Constellation Program and Orion Crew Capsule Project Office and provides test instrumentation and support personnel. Together, these teams are developing vehicle hardware, evolving proven technologies, and testing components and systems. Their work builds on powerful, reliable space shuttle propulsion elements and nearly a half-century of NASA space flight experience and technological advances. Ares I is an inline, two-stage rocket configuration topped by the Crew Exploration Vehicle, its service module, and a launch abort system. In this HD video image, processes for upper stage barrel fabrication are talking place. The aluminum panels are manufacturing process demonstration articles that will undergo testing until perfected. The panels are built by AMRO Manufacturing located in El Monte, California. (Highest resolution Available)

  11. ARES I Upper Stage Fabrication

    NASA Technical Reports Server (NTRS)

    2007-01-01

    Under the goals of the Vision for Space Exploration, Ares I is a chief component of the cost-effective space transportation infrastructure being developed by NASA's Constellation Program. This transportation system will safely and reliably carry human explorers back to the moon, and then onward to Mars and other destinations in the solar system. The Ares I effort includes multiple project element teams at NASA centers and contract organizations around the nation, and is managed by the Exploration Launch Projects Office at NASA's Marshall Space Flight Center (MFSC). ATK Launch Systems near Brigham City, Utah, is the prime contractor for the first stage booster. ATK's subcontractor, United Space Alliance of Houston, is designing, developing and testing the parachutes at its facilities at NASA's Kennedy Space Center in Florida. NASA's Johnson Space Center in Houston hosts the Constellation Program and Orion Crew Capsule Project Office and provides test instrumentation and support personnel. Together, these teams are developing vehicle hardware, evolving proven technologies, and testing components and systems. Their work builds on powerful, reliable space shuttle propulsion elements and nearly a half-century of NASA space flight experience and technological advances. Ares I is an inline, two-stage rocket configuration topped by the Crew Exploration Vehicle, its service module, and a launch abort system. In this HD video image, processes for upper stage barrel fabrication are talking place. Aluminum panels are manufacturing process demonstration articles that will undergo testing until perfected. The panels are built by AMRO Manufacturing located in El Monte, California. (Largest resolution available)

  12. Ares I Upper Stage Fabrication

    NASA Technical Reports Server (NTRS)

    2006-01-01

    Under the goals of the Vision for Space Exploration, Ares I is a chief component of the cost-effective space transportation infrastructure being developed by NASA's Constellation Program. This transportation system will safely and reliably carry human explorers back to the moon, and then onward to Mars and other destinations in the solar system. The Ares I effort includes multiple project element teams at NASA centers and contract organizations around the nation, and is managed by the Exploration Launch Projects Office at NASA's Marshall Space Flight Center (MFSC). ATK Launch Systems near Brigham City, Utah, is the prime contractor for the first stage booster. ATK's subcontractor, United Space Alliance of Houston, is designing, developing and testing the parachutes at its facilities at NASA's Kennedy Space Center in Florida. NASA's Johnson Space Center in Houston hosts the Constellation Program and Orion Crew Capsule Project Office and provides test instrumentation and support personnel. Together, these teams are developing vehicle hardware, evolving proven technologies, and testing components and systems. Their work builds on powerful, reliable space shuttle propulsion elements and nearly a half-century of NASA space flight experience and technological advances. Ares I is an inline, two-stage rocket configuration topped by the Crew Exploration Vehicle, its service module, and a launch abort system. This HD video image depicts a manufactured aluminum panel that will be used to fabricate the Ares I upper stage barrel, undergoing a confidence panel test. In this test, the bent aluminum is stressed to breaking point and thoroughly examined. The panels are manufactured by AMRO Manufacturing located in El Monte, California. (Highest resolution available)

  13. Ares I Upper Stage Fabrication

    NASA Technical Reports Server (NTRS)

    2007-01-01

    Under the goals of the Vision for Space Exploration, Ares I is a chief component of the cost-effective space transportation infrastructure being developed by NASA's Constellation Program. This transportation system will safely and reliably carry human explorers back to the moon, and then onward to Mars and other destinations in the solar system. The Ares I effort includes multiple project element teams at NASA centers and contract organizations around the nation, and is managed by the Exploration Launch Projects Office at NASA's Marshall Space Flight Center (MFSC). ATK Launch Systems near Brigham City, Utah, is the prime contractor for the first stage booster. ATK's subcontractor, United Space Alliance of Houston, is designing, developing and testing the parachutes at its facilities at NASA's Kennedy Space Center in Florida. NASA's Johnson Space Center in Houston hosts the Constellation Program and Orion Crew Capsule Project Office and provides test instrumentation and support personnel. Together, these teams are developing vehicle hardware, evolving proven technologies, and testing components and systems. Their work builds on powerful, reliable space shuttle propulsion elements and nearly a half-century of NASA space flight experience and technological advances. Ares I is an inline, two-stage rocket configuration topped by the Crew Exploration Vehicle, its service module, and a launch abort system. This HD video image depicts a manufactured aluminum panel, that will fabricate the Ares I upper stage barrel, undergoing a confidence panel test. In this test, the bent aluminum is stressed to breaking point and thoroughly examined. The panels are manufactured by AMRO Manufacturing located in El Monte, California. (Highest resolution available)

  14. Ares I Upper Stage Fabrication

    NASA Technical Reports Server (NTRS)

    2007-01-01

    Under the goals of the Vision for Space Exploration, Ares I is a chief component of the cost-effective space transportation infrastructure being developed by NASA's Constellation Program. This transportation system will safely and reliably carry human explorers back to the moon, and then onward to Mars and other destinations in the solar system. The Ares I effort includes multiple project element teams at NASA centers and contract organizations around the nation, and is managed by the Exploration Launch Projects Office at NASA's Marshall Space Flight Center (MFSC). ATK Launch Systems near Brigham City, Utah, is the prime contractor for the first stage booster. ATK's subcontractor, United Space Alliance of Houston, is designing, developing and testing the parachutes at its facilities at NASA's Kennedy Space Center in Florida. NASA's Johnson Space Center in Houston hosts the Constellation Program and Orion Crew Capsule Project Office and provides test instrumentation and support personnel. Together, these teams are developing vehicle hardware, evolving proven technologies, and testing components and systems. Their work builds on powerful, reliable space shuttle propulsion elements and nearly a half-century of NASA space flight experience and technological advances. Ares I is an inline, two-stage rocket configuration topped by the Crew Exploration Vehicle, its service module, and a launch abort system. This HD video image depicts a manufactured panel that will be used for the Ares I upper stage barrel fabrication. The aluminum panels are manufacturing process demonstration articles that will undergo testing until perfected. The panels are built by AMRO Manufacturing located in El Monte, California. (Highest resolution available)

  15. Ares I Upper Stage Fabrication

    NASA Technical Reports Server (NTRS)

    2007-01-01

    Under the goals of the Vision for Space Exploration, Ares I is a chief component of the cost-effective space transportation infrastructure being developed by NASA's Constellation Program. This transportation system will safely and reliably carry human explorers back to the moon, and then onward to Mars and other destinations in the solar system. The Ares I effort includes multiple project element teams at NASA centers and contract organizations around the nation, and is managed by the Exploration Launch Projects Office at NASA's Marshall Space Flight Center (MFSC). ATK Launch Systems near Brigham City, Utah, is the prime contractor for the first stage booster. ATK's subcontractor, United Space Alliance of Houston, is designing, developing and testing the parachutes at its facilities at NASA's Kennedy Space Center in Florida. NASA's Johnson Space Center in Houston hosts the Constellation Program and Orion Crew Capsule Project Office and provides test instrumentation and support personnel. Together, these teams are developing vehicle hardware, evolving proven technologies, and testing components and systems. Their work builds on powerful, reliable space shuttle propulsion elements and nearly a half-century of NASA space flight experience and technological advances. Ares I is an inline, two-stage rocket configuration topped by the Crew Exploration Vehicle, its service module, and a launch abort system. This HD video image, depicts a manufactured aluminum panel, that will be used to fabricate the Ares I upper stage barrel, undergoing a confidence panel test. In this test, the bent aluminum is stressed to breaking point and thoroughly examined. The panels are manufactured by AMRO Manufacturing located in El Monte, California. (Highest resolution available)

  16. Ares I Upper Stage Fabrication

    NASA Technical Reports Server (NTRS)

    2007-01-01

    Under the goals of the Vision for Space Exploration, Ares I is a chief component of the cost-effective space transportation infrastructure being developed by NASA's Constellation Program. This transportation system will safely and reliably carry human explorers back to the moon, and then onward to Mars and other destinations in the solar system. The Ares I effort includes multiple project element teams at NASA centers and contract organizations around the nation, and is managed by the Exploration Launch Projects Office at NASA's Marshall Space Flight Center (MFSC). ATK Launch Systems near Brigham City, Utah, is the prime contractor for the first stage booster. ATK's subcontractor, United Space Alliance of Houston, is designing, developing and testing the parachutes at its facilities at NASA's Kennedy Space Center in Florida. NASA's Johnson Space Center in Houston hosts the Constellation Program and Orion Crew Capsule Project Office and provides test instrumentation and support personnel. Together, these teams are developing vehicle hardware, evolving proven technologies, and testing components and systems. Their work builds on powerful, reliable space shuttle propulsion elements and nearly a half-century of NASA space flight experience and technological advances. Ares I is an inline, two-stage rocket configuration topped by the Crew Exploration Vehicle, its service module, and a launch abort system. This HD video image depicts confidence testing of a manufactured aluminum panel that will fabricate the Ares I upper stage barrel. In this test, bent aluminum is stressed to breaking point and thoroughly examined. The panels are manufactured by AMRO Manufacturing located in El Monte, California. (Highest resolution available)

  17. Peer Tutoring and Clinical Stage: analysis of experience and potential applications in the First Level Degree Course in Nursing, section of Desenzano Del Garda.

    PubMed

    Lo Biondo, Paolo; Avino, Nicola; Podavini, Enrica; Prandelli, Matteo

    2015-01-01

    Among the various methods of learning and experience in the literature, the methodology of Peer Tutoring is particularly important for the formation of the student nurses. The Peer Tutoring identifies a model of cooperative learning, aiming to activate a spontaneous process to transfer knowledge, emotions and experiences from some members of a group to other members of equal status but with a difference in the knowledge and cognitive skills or relational. The First level degree course in Nursing, section of Desenzano del Garda (Brescia, Italy) has been applying a methodology that can be defined as Peer Tutoring for the last four years. The applicability of the method is based on the coupling of an expert student of the 3rd year of the course to a group of students from the 1st or 2nd year. The study has the main objective to analyze the experience in the branch of Desenzano del Garda and see if the learning method of the Peer Tutoring is valid within the context of clinical internship. The study, of descriptive-observational type, was conducted in the academic year 2013-2014. The samples in the research are two: the first sample consisted of 53 students in their first year of studies, 46 students of the 2nd year of the course and 30 students of the 3rd year of the course who attended the experience as tutoring students (students tutors), for a total of 129 students; the second sample consisted of 15 students of the 3rd year of the course who attended the experience of the Peer Tutoring applied to the Stage clinical students as tutors (students Tutor). The research allowed important information to be gathered regarding the utility and interventions to improve the quality of the project of Peer tutoring. Peer Tutoring is a learning methodology that works and that can be applied in learning pathways for nursing students. The training of students Tutor is a matter of considerable importance: in fact the students ask to be trained to respect the structure and functions

  18. Morphogenesis of early stage melanoma

    NASA Astrophysics Data System (ADS)

    Chatelain, Clément; Amar, Martine Ben

    2015-08-01

    Melanoma early detection is possible by simple skin examination and can insure a high survival probability when successful. However it requires efficient methods for identifying malignant lesions from common moles. This paper provides an overview first of the biological and physical mechanisms controlling melanoma early evolution, and then of the clinical tools available today for detecting melanoma in vivo at an early stage. It highlights the lack of diagnosis methods rationally linking macroscopic observables to the microscopic properties of the tissue, which define the malignancy of the tumor. The possible inputs of multiscale models for improving these methods are shortly discussed.

  19. Multiple angle single stage scrubber

    SciTech Connect

    Ostlie, L.

    1982-02-02

    A scrubber for cleansing flue gases is disclosed. The scrubber includes a housing which defines a channel. The channel includes a scrubber stage wherein vertically spaced rows of deflecting members of l-shaped cross-section are disposed. In a given row of deflecting members, a plurality of flow paths are defined between horizontally adjacent deflecting members. Each deflecting member has an upper arm and a lower arm. The lowermost edge of the lower arms of the deflecting members in one row are disposed between vertical projections from the uppermost edges of upper arms of deflecting members in a row below the last mentioned row.

  20. Single-stage Mars mission

    NASA Technical Reports Server (NTRS)

    1991-01-01

    President Bush established a three phase Space Exploration Initiative for the future of space exploration. The first phase is the design and construction of Space Station Freedom. The second phase is permanent lunar base. The last phase of the Initiative is the construction of a Mars outpost. The design presented is the concept of a single-stage Mars mission developed by the University of Minnesota Aerospace Design Course. The mission will last approximately 500 days including a 30-60 day stay on Mars.

  1. A simplified staging system based on the radiological findings in different stages of ochronotic spondyloarthropathy

    PubMed Central

    Jebaraj, Isaac; Chacko, Binita Riya; Chiramel, George Koshy; Matthai, Thomas; Parameswaran, Apurve

    2013-01-01

    This study describes a group of 26 patients with ochronotic spondyloarthropathy who were on regular treatment and follow-up at a tertiary level hospital and proposes a simplified staging system for ochronotic spondyloarthropathy based on radiographic findings seen in the thoracolumbar spine. This proposed classification makes it easy to identify the stage of the disease and start the appropriate management at an early stage. Four progressive stages are described: an inflammatory stage (stage 1), the stage of early discal calcification (stage 2), the stage of fibrous ankylosis (stage 3), and the stage of bony ankylosis (stage 4). To our knowledge, this is the largest reported series of radiological description of spinal ochronosis, and emphasizes the contribution of the spine radiograph in the diagnosis and staging of the disease. PMID:23986625

  2. Sleep stages, memory and learning.

    PubMed

    Dotto, L

    1996-04-15

    Learning and memory can be impaired by sleep loss during specific vulnerable "windows" for several days after new tasks have been learned. Different types of tasks are differentially vulnerable to the loss of different stages of sleep. Memory required to perform cognitive procedural tasks is affected by the loss of rapid-eye-movement (REM) sleep on the first night after learning occurs and again on the third night after learning. REM-sleep deprivation on the second night after learning does not produce memory deficits. Declarative memory, which is used for the recall of specific facts, is not similarly affected by REM-sleep loss. The learning of procedural motor tasks, including those required in many sports, is impaired by the loss of stage 2 sleep, which occurs primarily in the early hours of the morning. These findings have implications for the academic and athletic performance of students and for anyone whose work involves ongoing learning and demands high standards of performance. PMID:8612256

  3. Orbital debris from upper-stage breakup

    NASA Technical Reports Server (NTRS)

    Loftus, Joseph P., Jr. (Editor)

    1989-01-01

    The present conference on the effects of launch vehicle upper-stage breakup on the orbital debris scenario discusses an analysis of the SPOT 1 Ariane third stage, the explosive fragmentation of orbiting propellant tanks, albedo estimates for debris, Ariane-related debris in deep-space orbit, and the relationship of hypervelocity impacts to upper-stage breakups. Also discussed are the prospects for and the economics of the future removal of orbital debris, collision probabilities in GEO, current operational practices for Delta second stage breakup prevention, breakup-precluding modifications to the Ariane third stage, and the safing of the H-1 second stage after spacecraft separation.

  4. Two stage indirect evaporative cooling system

    DOEpatents

    Bourne, Richard C.; Lee, Brian E.; Callaway, Duncan

    2005-08-23

    A two stage indirect evaporative cooler that moves air from a blower mounted above the unit, vertically downward into dry air passages in an indirect stage and turns the air flow horizontally before leaving the indirect stage. After leaving the dry passages, a major air portion travels into the direct stage and the remainder of the air is induced by a pressure drop in the direct stage to turn 180.degree. and returns horizontally through wet passages in the indirect stage and out of the unit as exhaust air.

  5. Evaluation of aqueous and ethanol extract of bioactive medicinal plant, Cassia didymobotrya (Fresenius) Irwin & Barneby against immature stages of filarial vector, Culex quinquefasciatus Say (Diptera: Culicidae)

    PubMed Central

    Nagappan, Raja

    2012-01-01

    Objective To evaluate aqueous and ethanol extract of Cassia didymobotrya leaves against immature stages of Culex quinquefasciatus. Methods The mortality rate of immature mosquitoes was tested in wide and narrow range concentration of the plant extract based on WHO standard protocol. The wide range concentration tested in the present study was 10 000, 1 000, 100, 10 and 1 mg/L and narrow range concentration was 50, 100, 150, 200 and 250 mg/L. Results 2nd instar larvae exposed to 100 mg/L and above concentration of ethanol extract showed 100% mortality. Remaining stages such as 3rd, 4th and pupa, 100% mortality was observed at 1 000 mg/L and above concentration after 24 h exposure period. In aqueous extract all the stages 100% mortality was recorded at 1 000 mg/L and above concentration. In narrow range concentration 2nd instar larvae 100% mortality was observed at 150 mg/L and above concentration of ethanol extract. The remaining stages 100% mortality was recorded at 250 mg/L. In aqueous extract all the tested immature stages 100% mortality was observed at 250 mg/L concentration after 24 h exposure period. The results clearly indicate that the rate of mortality was based dose of the plant extract and stage of the mosquitoes. Conclusions From this study it is confirmed and concluded that Cassia didymobotrya is having active principle which is responsible for controlling Culex quinquefasciatus. The isolation of bioactive molecules and development of simple formulation technique is important for large scale implementation. PMID:23569999

  6. The Nuclear Cryogenic Propulsion Stage

    NASA Technical Reports Server (NTRS)

    Houts, Michael G.; Kim, Tony; Emrich, William J.; Hickman, Robert R.; Broadway, Jeramie W.; Gerrish, Harold P.; Doughty, Glen; Belvin, Anthony; Borowski, Stanley K.; Scott, John

    2014-01-01

    The fundamental capability of Nuclear Thermal Propulsion (NTP) is game changing for space exploration. A first generation Nuclear Cryogenic Propulsion Stage (NCPS) based on NTP could provide high thrust at a specific impulse above 900 s, roughly double that of state of the art chemical engines. Characteristics of fission and NTP indicate that useful first generation systems will provide a foundation for future systems with extremely high performance. The role of the NCPS in the development of advanced nuclear propulsion systems could be analogous to the role of the DC-3 in the development of advanced aviation. Progress made under the NCPS project could help enable both advanced NTP and advanced Nuclear Electric Propulsion (NEP). Nuclear propulsion can be affordable and viable compared to other propulsion systems and must overcome a biased public fear due to hyper-environmentalism and a false perception of radiation and explosion risk.

  7. The Nuclear Cryogenic Propulsion Stage

    NASA Technical Reports Server (NTRS)

    Houts, Michael G.; Kim, Tony; Emrich, William J.; Hickman, Robert R.; Broadway, Jeramie W.; Gerrish, Harold P.; Doughty, Glen; Belvin, Anthony; Borowski, Stanley K.; Scott, John

    2014-01-01

    The fundamental capability of Nuclear Thermal Propulsion (NTP) is game changing for space exploration. A first generation Nuclear Cryogenic Propulsion Stage (NCPS) based on NTP could provide high thrust at a specific impulse above 900 s, roughly double that of state of the art chemical engines. Characteristics of fission and NTP indicate that useful first generation systems will provide a foundation for future systems with extremely high performance. The role of the NCPS in the development of advanced nuclear propulsion systems could be analogous to the role of the DC-3 in the development of advanced aviation. Progres made under the NCPS project could help enable both advanced NTP and advanced Nuclear Electric Propulsion (NEP).

  8. Early stages of Ostwald ripening

    NASA Astrophysics Data System (ADS)

    Shneidman, Vitaly A.

    2013-07-01

    The Becker-Döring (BD) nucleation equation is known to predict a narrow double-exponential front (DEF) in the distribution of growing particles over sizes, which is due to early transient effects. When mass conservation is included, nucleation is eventually exhausted while independent growth is replaced by ripening. Despite the enormous difference in the associated time scales, and the resulting demand on numerics, within the generalized BD model the early DEF is shown to be crucial for the selection of the unique self-similar Lifshitz-Slyozov-Wagner asymptotic regime. Being preserved till the latest stages of growth, the DEF provides a universal part of the initial conditions for the ripening problem, regardless of the mass exchange mechanism between the nucleus and the matrix.

  9. Second Stage Turbine Bucket Airfoil.

    DOEpatents

    Xu, Liming; Ahmadi, Majid; Humanchuk, David John; Moretto, Nicholas; Delehanty, Richard Edward

    2003-05-06

    The second-stage buckets have airfoil profiles substantially in accordance with Cartesian coordinate values of X, Y and Z set forth in inches in Table I wherein Z is a perpendicular distance from a plane normal to a radius of the turbine centerline and containing the X and Y values with the Z value commencing at zero in the X, Y plane at the radially innermost aerodynamic section of the airfoil and X and Y are coordinate values defining the airfoil profile at each distance Z. The X, Y and Z values may be scaled as a function of the same constant or number to provide a scaled-up or scaled-down airfoil section for the bucket.

  10. Survival by Stage of Soft Tissue Sarcoma

    MedlinePlus

    ... Next Topic How are soft tissue sarcomas treated? Survival by stage of soft tissue sarcoma Survival rates ... observed, not relative survival): Stage 5-year observed survival rate I 90% II 81% III 56% IV ...

  11. Ares I Upper Stage Fabrication

    NASA Technical Reports Server (NTRS)

    2007-01-01

    Under the goals of the Vision for Space Exploration, Ares I is a chief component of the cost-effective space transportation infrastructure being developed by NASA's Constellation Program. This transportation system will safely and reliably carry human explorers back to the moon, and then onward to Mars and other destinations in the solar system. The Ares I effort includes multiple project element teams at NASA centers and contract organizations around the nation, and is managed by the Exploration Launch Projects Office at NASA's Marshall Space Flight Center (MFSC). ATK Launch Systems near Brigham City, Utah, is the prime contractor for the first stage booster. ATK's subcontractor, United Space Alliance of Houston, is designing, developing and testing the parachutes at its facilities at NASA's Kennedy Space Center in Florida. NASA's Johnson Space Center in Houston hosts the Constellation Program and Orion Crew Capsule Project Office and provides test instrumentation and support personnel. Together, these teams are developing vehicle hardware, evolving proven technologies, and testing components and systems. Their work builds on powerful, reliable space shuttle propulsion elements and nearly a half-century of NASA space flight experience and technological advances. Ares I is an inline, two-stage rocket configuration topped by the Crew Exploration Vehicle, its service module, and a launch abort system. This HD video image depicts the manufacturing of aluminum panels that will be used to form the Ares I barrel. The panels are manufacturing process demonstration articles that will undergo testing until perfected. The panels are built by AMRO Manufacturing located in El Monte, California. (Highest resolution available)

  12. Two-Stage Series-Resonant Inverter

    NASA Technical Reports Server (NTRS)

    Stuart, Thomas A.

    1994-01-01

    Two-stage inverter includes variable-frequency, voltage-regulating first stage and fixed-frequency second stage. Lightweight circuit provides regulated power and is invulnerable to output short circuits. Does not require large capacitor across ac bus, like parallel resonant designs. Particularly suitable for use in ac-power-distribution system of aircraft.

  13. Cisplatin and Paclitaxel in Treating Patients With Stage IIB, Stage IIC, Stage III, or Stage IV Ovarian Epithelial Cancer, Fallopian Tube Cancer, or Primary Peritoneal Cavity Cancer

    ClinicalTrials.gov

    2014-12-29

    Chemotherapeutic Agent Toxicity; Endometrial Adenocarcinoma; Fallopian Tube Carcinoma; Gastrointestinal Complication; Malignant Ovarian Mixed Epithelial Tumor; Neurotoxicity Syndrome; Ovarian Brenner Tumor; Ovarian Clear Cell Cystadenocarcinoma; Ovarian Mucinous Cystadenocarcinoma; Ovarian Serous Cystadenocarcinoma; Primary Peritoneal Carcinoma; Stage II Ovarian Cancer; Stage III Ovarian Cancer; Stage IV Ovarian Cancer; Undifferentiated Ovarian Carcinoma

  14. Paclitaxel and Carboplatin With or Without Bevacizumab in Treating Patients With Stage II, Stage III, or Stage IV Ovarian Epithelial Cancer, Primary Peritoneal Cancer, or Fallopian Tube Cancer

    ClinicalTrials.gov

    2015-12-21

    Fallopian Tube Endometrioid Adenocarcinoma; Fallopian Tube Mucinous Adenocarcinoma; Fallopian Tube Transitional Cell Carcinoma; Malignant Ovarian Mixed Epithelial Tumor; Ovarian Brenner Tumor; Ovarian Clear Cell Adenocarcinofibroma; Ovarian Endometrioid Adenocarcinoma; Ovarian Mucinous Adenocarcinoma; Ovarian Serous Adenocarcinoma; Ovarian Transitional Cell Carcinoma; Primary Peritoneal Serous Adenocarcinoma; Stage IIA Fallopian Tube Cancer; Stage IIA Ovarian Cancer; Stage IIB Fallopian Tube Cancer; Stage IIB Ovarian Cancer; Stage IIC Fallopian Tube Cancer; Stage IIC Ovarian Cancer; Stage IIIA Fallopian Tube Cancer; Stage IIIA Ovarian Cancer; Stage IIIA Primary Peritoneal Cancer; Stage IIIB Fallopian Tube Cancer; Stage IIIB Ovarian Cancer; Stage IIIB Primary Peritoneal Cancer; Stage IIIC Fallopian Tube Cancer; Stage IIIC Ovarian Cancer; Stage IIIC Primary Peritoneal Cancer; Stage IV Fallopian Tube Cancer; Stage IV Ovarian Cancer; Stage IV Primary Peritoneal Cancer; Undifferentiated Ovarian Carcinoma

  15. The Nuclear Cryogenic Propulsion Stage

    NASA Technical Reports Server (NTRS)

    Houts, Michael G.; Kim, Tony; Emrich, William J.; Hickman, Robert R.; Broadway, Jeramie W.; Gerrish, Harold P.; Belvin, Anthony D.; Borowski, Stanley K.; Scott, John H.

    2014-01-01

    Nuclear Thermal Propulsion (NTP) development efforts in the United States have demonstrated the technical viability and performance potential of NTP systems. For example, Project Rover (1955 - 1973) completed 22 high power rocket reactor tests. Peak performances included operating at an average hydrogen exhaust temperature of 2550 K and a peak fuel power density of 5200 MW/m3 (Pewee test), operating at a thrust of 930 kN (Phoebus-2A test), and operating for 62.7 minutes in a single burn (NRX-A6 test). Results from Project Rover indicated that an NTP system with a high thrust-to-weight ratio and a specific impulse greater than 900 s would be feasible. Excellent results were also obtained by the former Soviet Union. Although historical programs had promising results, many factors would affect the development of a 21st century nuclear thermal rocket (NTR). Test facilities built in the US during Project Rover no longer exist. However, advances in analytical techniques, the ability to utilize or adapt existing facilities and infrastructure, and the ability to develop a limited number of new test facilities may enable affordable development, qualification, and utilization of a Nuclear Cryogenic Propulsion Stage (NCPS). Bead-loaded graphite fuel was utilized throughout the Rover/NERVA program, and coated graphite composite fuel (tested in the Nuclear Furnace) and cermet fuel both show potential for even higher performance than that demonstrated in the Rover/NERVA engine tests.. NASA's NCPS project was initiated in October, 2011, with the goal of assessing the affordability and viability of an NCPS. FY 2014 activities are focused on fabrication and test (non-nuclear) of both coated graphite composite fuel elements and cermet fuel elements. Additional activities include developing a pre-conceptual design of the NCPS stage and evaluating affordable strategies for NCPS development, qualification, and utilization. NCPS stage designs are focused on supporting human Mars

  16. Three stage semelparous Leslie models.

    PubMed

    Cushing, J M

    2009-07-01

    oscillations (not necessarily periodic) with separated life-cycle stages, while weak interactions promote stable equilibration with overlapping life-cycle stages. Methods used include the theory of planar monotone maps, average Lyapunov functions, and bifurcation theory techniques. PMID:18777023

  17. Saturn V S-IC-T Stage

    NASA Technical Reports Server (NTRS)

    1964-01-01

    Pictured is the Saturn V S-IC-T stage (static testing stage) on a transporter showing its forward end in building 4705 at the Marshall Space Flight Center (MSFC). This stage underwent numerous static firings at the newly-built S-IC Static Test Stand at the MSFC west test area. The S-IC (first) stage used five F-1 engines that produced a total thrust of 7,500,000 pounds as each engine produced 1,500,000 pounds of thrust. The S-IC stage lifted the Saturn V vehicle and Apollo spacecraft from the launch pad.

  18. Saturn V S-IC-T Stage

    NASA Technical Reports Server (NTRS)

    1965-01-01

    Pictured is the Saturn V S-IC-T stage (static testing stage) being assembled in the horizontal assembly station at the Marshall Space Flight Center (MSFC), building 4705. This stage underwent numerous static firings at the newly-built S-IC Static Test Stand at the MSFC west test area. The S-IC (first) stage used five F-1 engines that produced a total thrust of 7,500,000 pounds as each engine produced 1,500,000 pounds of thrust. The S-IC stage lifted the Saturn V vehicle and Apollo spacecraft from the launch pad.

  19. Lenalidomide and Rituximab in Treating Patients With Previously Untreated Stage II, Stage III, or Stage IV Follicular Non-Hodgkin Lymphoma

    ClinicalTrials.gov

    2016-07-28

    Stage II Grade 1 Contiguous Follicular Lymphoma; Stage II Grade 1 Non-Contiguous Follicular Lymphoma; Stage II Grade 2 Contiguous Follicular Lymphoma; Stage II Grade 2 Non-Contiguous Follicular Lymphoma; Stage II Grade 3 Contiguous Follicular Lymphoma; Stage II Grade 3 Non-Contiguous Follicular Lymphoma; Stage III Grade 1 Follicular Lymphoma; Stage III Grade 2 Follicular Lymphoma; Stage III Grade 3 Follicular Lymphoma; Stage IV Grade 1 Follicular Lymphoma; Stage IV Grade 2 Follicular Lymphoma; Stage IV Grade 3 Follicular Lymphoma

  20. Staged direct injection diesel engine

    DOEpatents

    Baker, Quentin A.

    1985-01-01

    A diesel engine having staged injection for using lower cetane number fuels than No. 2 diesel fuel. The engine includes a main fuel injector and a pilot fuel injector. Pilot and main fuel may be the same fuel. The pilot injector injects from five to fifteen percent of the total fuel at timings from 20.degree. to 180.degree. BTDC depending upon the quantity of pilot fuel injected, the fuel cetane number and speed and load. The pilot fuel injector is directed toward the centerline of the diesel cylinder and at an angle toward the top of the piston, avoiding the walls of the cylinder. Stratification of the early injected pilot fuel is needed to reduce the fuel-air mixing rate, prevent loss of pilot fuel to quench zones, and keep the fuel-air mixture from becoming too fuel lean to become effective. In one embodiment, the pilot fuel injector includes a single hole for injection of the fuel and is directed at approximately 48.degree. below the head of the cylinder.