Science.gov

Sample records for 440f steel rollers

  1. Wear of Steel and Ti6Al4V Rollers in Vacuum

    NASA Technical Reports Server (NTRS)

    Krantz, Timothy L.; Shareef, Iqbal

    2012-01-01

    This investigation was prompted by results of a qualification test of a mechanism to be used for the James Webb Space Telescope. Post-test inspections of the qualification test article revealed some loose wear debris and wear of the steel rollers and the mating Ti6Al4V surfaces. An engineering assessment of the design and observations from the tested qualification unit suggested that roller misalignment was a controlling factor. The wear phenomena were investigated using dedicated laboratory experiments. Tests were done using a vacuum roller rig for a range of roller misalignment angles. The wear in these tests was mainly adhesive wear. The measured wear rates were highly correlated to the misalignment angle. For all tests with some roller misalignment, the steel rollers lost mass while the titanium rollers gained mass indicating strong adhesion of the steel with the titanium alloy. Inspection of the rollers revealed that the adhesive wear was a two-way process as titanium alloy was found on the steel rollers and vice versa. The qualification test unit made use of 440F steel rollers in the annealed condition. Both annealed 440F steel rollers and hardened 440C rollers were tested in the vacuum roller rig to investigate possibility to reduce wear rates and the risk of loose debris formation. The 440F and 440C rollers had differing wear behaviors with significantly lesser wear rates for the 440C. For the test condition of zero roller misalignment, the adhesive wear rates were very low, but still some loose debris was formed

  2. Experimental Investigation of Forces Produced by Misaligned Steel Rollers

    NASA Technical Reports Server (NTRS)

    Krantz, Timothy; DellaCorte, Christopher; Dube, Michael

    2010-01-01

    The International Space Station Solar Alpha Rotary Joint (SARJ) uses a roller-based mechanism for positioning of the solar arrays. The forces and moments that develop at the roller interfaces are influenced by the design including the kinematic constraints and the lubrication condition. To help understand the SARJ operation, a set of dedicated experiments were completed using roller pairs. Of primary interest was to measure the axial force directed along the axis of rotation of the roller as a function of shaft misalignment. The conditions studied included dry and clean surfaces; one surface plated by a gold film, and greased surfaces. For the case of a bare 440C roller against a nitrided 15-5 roller without lubrication, the axial force can be as great as 0.4 times the normal load for a shaft angle of 0.5 degree. Such a magnitude of force on a roller in the SARJ mechanism would cause roller tipping and contact pressures much greater than anticipated by the designers. For the case of a bare 440C roller against a nitrided 15-5 roller with grease lubrication, the axial force does not exceed about 0.15 times the normal load even for the largest misalignment angles tested. Gold films provided good lubrication for the short duration testing reported herein. Grease lubrication limited the magnitude of the axial force to even smaller magnitudes than was achieved with the gold films. The experiments demonstrate the critical role of good lubrication for the SARJ mechanism.

  3. Experimental Investigation of Forces Produced by Misaligned Steel Rollers

    NASA Technical Reports Server (NTRS)

    Krantz, Timothy; DellaCorte, Christopher; Dube, Michael

    2010-01-01

    The International Space Station (ISS) Solar Alpha Rotary Joint (SARJ) uses a roller-based mechanism for positioning of the solar arrays. The forces and moments that develop at the roller interfaces are influenced by the design including the kinematic constraints and the lubrication condition. To help understand the SARJ operation, a set of dedicated experiments were completed using roller pairs. Of primary interest was to measure the axial force directed along the axis of rotation of the roller as a function of shaft misalignment. The conditions studied included dry and clean surfaces; one surface plated by a gold film, and greased surfaces. For the case of a bare 440C roller against a nitrided 15-5 roller without lubrication, the axial force can be as great as 0.4 times the normal load for a shaft angle of 0.5 deg. Such a magnitude of force on a roller in the SARJ mechanism would cause roller tipping and contact pressures much greater than anticipated by the designers. For the case of a bare 440C roller against a nitrided 15-5 roller with grease lubrication, the axial force does not exceed about 0.15 times the normal load even for the largest misalignment angles tested. Gold films provided good lubrication for the short duration testing reported herein. Grease lubrication limited the magnitude of the axial force to even smaller magnitudes than was achieved with the gold films. The experiments demonstrate the critical role of good lubrication for the SARJ mechanism.

  4. Adhesive Wear of Rollers in Vacuum

    NASA Technical Reports Server (NTRS)

    Shaeef, Iqbal; Krantz, Timothy L.

    2012-01-01

    This work was done to support NASA's James Webb Space Telescope that is equipped with a Near Infrared Camera and Spectrograph and Micro Shutter Assembly (MSA). A MSA mechanism's qualification test in cryogenic vacuum at 30deg K for 96K cycles resulted in roller wear and formation of some debris. Lab tests in vacuum were conducted at NASA Glenn Research Center (GRC) to understand the wear of Ti6Al4V mated with 440F steel rollers. Misalignment angle was found to have the most significant effect on debris formation. At misalignment angle of 1.4deg, significant amount of wear debris were formed within 50,000 cycles. Very few wear particles were found for a zero misalignment angle, and the total wear was small even after 367,000 cycles. The mode of wear in all the tests was attributed to adhesion, which was clearly evident from video records as well as the plate-like amalgamated debris material from both rollers. The adhesive wear rate was found to be approximately proportional to the misalignment angle. The wear is a two-way phenomenon, and the mixing of both roller materials in wear debris was confirmed by x-ray fluorescence (XRF) and EDX spectra. While there was a net loss of mass from the steel rollers, XRF and energy dispersive x-ray (EDX) spectra showed peaks of Ti on steel rollers, and peaks of Fe on Ti rollers. These results are useful for designers in terms of maintaining appropriate tolerances to avoid misalignment of rolling elements and the resulting severe wear

  5. New steels and methods for induction hardening of bearing rings and rollers

    SciTech Connect

    Ouchakov, B.K.; Shepeljakovsky, K.Z.

    1998-12-31

    The new method of through-surface hardening (TSH) of bearing rings and rollers was developed and used in Russia and former USSR. The principles of the method include the use of special steels of low or controlled hardenability, through-the-section induction of furnace heating and intense quenching of the parts by water stream in special devices. Due to the low hardenability of applied steels, the bearing rings and rollers have high-strength martensitic surface layer, combined with a core strengthened with a troostite and sorbite structure. High compressive residual stresses are formed in the martensitic surface layers. For a long time TSH has been successfully used for inner rings of bearings for railway car boxes, large rings and rollers of bearings for cement furnaces and rolling mills. Recently TSH was used for hollow rollers of railway bearings. For bearing rings made of SAE 52100 type high-carbon, chromium-alloyed steel a new method of low-deformation hardening was developed. The method is based on self-calibration of the rings during the quenching process and is intended for through hardening by induction heating and quenching by rapidly moved water stream.

  6. Rolling Contact Fatigue Life of Steel Rollers Treated by Cavitation Peening and Shot Peening

    NASA Astrophysics Data System (ADS)

    Seki, Masanori; Soyama, Hitoshi; Kobayashi, Yuji; Gowa, Daisuke; Fujii, Masahiro

    The purpose of this study is to investigate the influence of peening on the rolling contact fatigue (RCF) life of steel rollers. First, steel rollers were treated by three types of peenings to ensure the same surface roughness of peened rollers. One is the cavitation peening (CP) used a cavitating jet in water with an injection pressure of 30 MPa, and the others are the fine particle peening (FPP) with a shot diameter of 0.1 mm and the normal shot peening (NSP) with a shot diameter of 0.3 mm. The surface hardness and the surface compressive residual stress of the steel rollers were increased by all the peenings. In particular, they were most increased by the FPP. On the other hand, the work-hardened depth due to the CP and the NSP was larger than that due to the FPP. As a result of the RCF tests, the RCF lives of the steel rollers were improved by all the peenings, and they were most improved by the NSP. Judging from the pmax - N curves and the [A(σy/√3 HV)]max - N curves, the improvement in RCF lives due to the FPP depended heavily on the increase in surface hardness due to that, and the effects of the CP and the NSP on the RCF were equivalent under the same surface roughness and the same surface hardness. It follows from these that the surface treatment condition should be selected according to the rolling contact conditions and the failure modes of machine elements.

  7. Comparison of Roller Burnishing Method with Other Hole Surface Finishing Processes Applied on AISI 304 Austenitic Stainless Steel

    NASA Astrophysics Data System (ADS)

    Akkurt, Adnan

    2011-08-01

    Component surface quality and selection of the optimum material are the main factors determining the performance of components used in machine manufacturing. The level of hole surface quality can be evaluated by the measurements regarding surface roughness, micro-hardness, and cylindricity. In this study, data had been obtained for different hole drilling methods. The characteristics of materials obtained after applications were compared for different hole-finishing processes to identify best hole drilling method. AISI 304 austenitic stainless steel material was used. Surface finishing of holes were performed using drilling, turning, reaming, grinding, honing, and roller burnishing methods. The results of the study show that the roller burnishing method gives the best results for mechanical, metallurgical properties, and hole surface quality of the material. On the other hand, the worst characteristics were obtained in the drilling method.

  8. Study on stable and meta-stable carbides in a high speed steel for rollers during tempering processes

    NASA Astrophysics Data System (ADS)

    Guo, Jing; Qu, Hong-wei; Liu, Li-gang; Sun, Yan-liang; Zhang, Yue; Yang, Qing-xiang

    2013-02-01

    A high speed steel (HSS) was studied for rollers in this work. The steel was quenched at 1150°C and tempered at 520°C. The phase structures of the steel were determined by X-ray diffraction (XRD), and the hardness of specimens was measured. The volume fraction of carbides was counted by Image-Pro Plus software. The typical microstructures were observed by field emission scanning electron microscope (FESEM). Stable and meta-stable carbides were deduced by removing the existing phases one by one in the Fe-C equilibrium calculation. It is found that the precipitated carbides are bulk-like MC, long stripe-like M2C, fishbone-like M6C, and daisy-like M7C3 during the tempering process. The stable carbides are MC and M6C, but the meta-stable ones are M2C, M7C3, and M3C.

  9. Roller Coasters!

    ERIC Educational Resources Information Center

    Ansberry, Karen; Morgan, Emily

    2008-01-01

    Students of all ages are fascinated by the ups, downs, loops, and twists of roller coaster rides! What they may not realize is that there is a lot of science involved in making a roller coaster work. This month's column puts students in the shoes of a roller coaster designer as they work in teams to create their own roller coasters. (Contains 1…

  10. Effect of Roller Geometry on Roller Bearing Load-Life Relation

    NASA Technical Reports Server (NTRS)

    Oswald, Fred B.; Zaretsky, Erwin V.; Poplawski, Joseph V.

    2015-01-01

    Cylindrical roller bearings typically employ roller profile modification to equalize load distribution, minimize stress concentration at roller ends and allow for a small amount of misalignment. The 1947 Lundberg-Palmgren analysis reported an inverse fourth power relation between load and life for roller bearings with line contact. In 1952, Lundberg and Palmgren changed their load-life exponent to 10/3 for roller bearings, assuming mixed line and point contact. The effect of roller-crown profile was reanalyzed in this paper to determine the actual load-life relation for modified roller profiles. For uncrowned rollers (line contact), the load-life exponent is p = 4, in agreement with the 1947 Lundberg-Palmgren value but crowning reduces the value of the exponent, p. The lives of modern roller bearings made from vacuum-processed steels significantly exceed those predicted by the Lundberg-Palmgren theory. The Zaretsky rolling-element bearing life model of 1996 produces a load-life exponent of p = 5 for flat rollers, which is more consistent with test data. For the Zaretsky model with fully crowned rollers p = 4.3. For an aerospace profile and chamfered rollers, p = 4.6. Using the 1952 Lundberg-Palmgren value p = 10/3, the value incorporated in ANSI/ABMA and ISO bearing standards, can create significant life calculation errors for roller bearings.

  11. Roller skewing measurements in cylindrical roller bearings

    NASA Technical Reports Server (NTRS)

    Nypan, L. J.

    1981-01-01

    Measurements of roller skewing in a 118 mm bore roller bearing operating at shaft speeds to 12,000 rpm are reported. High speed motion pictures of a modified roller were taken through a derotation prism to record skewing as the roller moved through loaded and unloaded regions of the bearing. Subsequent frame by frame measurement of the photographic film provided information on roller skewing. Radial and tangential skew amplitudes of 0.4 to 0.5 degrees were observed with 0.5 degree misalignment.

  12. Rotary roller of no. 2 seamless line in bays 19 ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Rotary roller of no. 2 seamless line in bays 19 and 20 of the main pipe mill building looking north. - U.S. Steel National Tube Works, Main Pipe Mill Building, Along Monongahela River, McKeesport, Allegheny County, PA

  13. Rollerized timing lifter

    SciTech Connect

    Rhodes, G.E.

    1988-05-03

    A rollerized timing lifter assembly is described comprising: a first tubular roller body sleeve having a top end and a bottom end; a roller; means for mounting the roller on the bottom end of the first tubular roller body sleeve; the first tubular roller body sleeve having an oil collecting channel and an oil feed port hole extending through the first tubular roller body sleeve; a second tubular body with a top end and a closed bottom end that is placed within the first tubular roller body sleeve and engaged telescopically a shoulder at near bottom of the first tubular roller body sleeve; the second tubular body having an external collecting channel positioned around the second tubular body and a second port hole to admit oil through the second tubular body; a hollow cylindrical plunger axially slideable in the second tubular body and enclosing a pressure chamber in the lower end of the second tubular body; a port in the plunger communicating with the first and second mentioned ports to admit oil into the plunger; and a valve in the plunger opening into the pressure chamber and means for receiveably capturing the bottom end of a push rod in a top end of the plunger.

  14. 14. UPPER SHOES, FIXED SHOES, ROLLER SHOES, CENTER WEB, AND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. UPPER SHOES, FIXED SHOES, ROLLER SHOES, CENTER WEB, AND ROLLER BED PLATES. (Also includes a sheet index and a schedule of parts). American Bridge Company, Ambridge Plant No. 5, sheet no. 4, dated April 7, 1928, order no. F5073. For U.S. Steel Products Company, Pacific Coast Depot, order no. SF578. For Southern Pacific Company, order no. 8873-P-28746. various scales. - Napa River Railroad Bridge, Spanning Napa River, east of Soscol Avenue, Napa, Napa County, CA

  15. Worm drive detail, roller hoist mechanism, rolling crest roller gate ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Worm drive detail, roller hoist mechanism, rolling crest roller gate - plan and sections - Grand Valley Diversion Dam, Half a mile north of intersection of I-70 & Colorado State Route 65, Cameo, Mesa County, CO

  16. EVALUATING A FIBERGLASS ROLLER COVERING ON A ROLLER GIN STAND

    Technology Transfer Automated Retrieval System (TEKTRAN)

    An experimental roller covering, made from woven fiberglass, was tested on a roller gin stand to evaluate its ginning performance and effect on fiber quality. The experimental roller covering was much more aggressive than the standard covering; it ginned at twice the rate (2.4 vs. 1.2 bales per hour...

  17. The World's Best Roller Coasters.

    ERIC Educational Resources Information Center

    Jones, T. Griffith; Jones, Linda Cronin

    1995-01-01

    Constructing model roller coasters is a great way for students to explore concepts related to energy and motion. Describes making a model roller coaster with 4th grade students. Students learn about different forms of energy and answer their own questions about roller coasters. (NB)

  18. Variable loading roller

    DOEpatents

    Williams, D.M.

    1988-01-21

    An automatic loading roller for transmitting torque in traction drive devices in manipulator arm joints includes a two-part camming device having a first cam portion rotatable in place on a shaft by an input torque and a second cam portion coaxially rotatable and translatable having a rotating drive surface thereon for engaging the driven surface of an output roller with a resultant force proportional to the torque transmitted. Complementary helical grooves in the respective cam portions interconnected through ball bearings interacting with those grooves effect the rotation and translation of the second cam portion in response to rotation of the first. 14 figs.

  19. Variable loading roller

    DOEpatents

    Williams, Daniel M.

    1989-01-01

    An automatic loading roller for transmitting torque in traction drive devices in manipulator arm joints includes a two-part camming device having a first cam portion rotatable in place on a shaft by an input torque and a second cam portion coaxially rotatable and translatable having a rotating drive surface thereon for engaging the driven surface of an output roller with a resultant force proportional to the torque transmitted. Complementary helical grooves on the respective cam portions interconnected through ball bearings interacting with those grooves effect the rotation and translation of the second cam portion in response to rotation of the first.

  20. Kinematic correction for roller skewing

    NASA Technical Reports Server (NTRS)

    Savage, M.; Loewenthal, S. H.

    1980-01-01

    A theory of kinematic stabilization of rolling cylinders is developed for high-speed cylindrical roller bearings. This stabilization requires race and roller crowning to product changes in the rolling geometry as the roller shifts axially. These changes put a reverse skew in the rolling elements by changing the rolling taper. Twelve basic possible bearing modifications are identified in this paper. Four have single transverse convex curvature in the rollers while eight have rollers with compound transverse curvature composed of a central cylindrical band of constant radius surrounded by symmetric bands with both slope and transverse curvature.

  1. Roller Coaster Science.

    ERIC Educational Resources Information Center

    Sumners, Carolyn; Jones, Howard L.

    1983-01-01

    Discusses the science of roller coasters, relating gravity, potential/kinetic energy, inertia, and centripetal force to the various parts of the ride, providing tips on linking classroom discussions to field trips. Includes sample student activity sheet and source for additional units using amusement park rides/playground activities to teach…

  2. Rotary roller mandrel of no. 2 seamless line in bays ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Rotary roller mandrel of no. 2 seamless line in bays 19 and 20 of the main pipe mill building looking south. - U.S. Steel National Tube Works, Main Pipe Mill Building, Along Monongahela River, McKeesport, Allegheny County, PA

  3. EVALUATION OF A LOW FRICTION - HIGH EFFICIENCY ROLLER BEARING ENGINE

    SciTech Connect

    Kolarik, Robert V. II; Shattuck, Charles W.; Copper, Anthony P.

    2009-06-30

    This Low Friction (High Efficiency Roller Bearing) Engine (LFE) report presents the work done by The Timken Company to conduct a technology demonstration of the benefits of replacing hydrodynamic bearings with roller bearings in the crankshaft and camshaft assemblies of an internal combustion engine for the purpose of collecting data sufficient to prove merit. The engines in the present study have been more extensively converted to roller bearings than any previous studies (40 needle roller bearings per engine) to gain understanding of the full potential of application of bearing technology. The project plan called for comparative testing of a production vehicle which was already respected for having demonstrated low engine friction levels with a rollerized version of that engine. Testing was to include industry standard tests for friction, emissions and fuel efficiency conducted on instrumented dynamometers. Additional tests for fuel efficiency, cold start resistance and other measures of performance were to be made in the actual vehicle. Comparative measurements of noise, vibration and harshness (NVH), were planned, although any work to mitigate the suspected higher NVH level in the rollerized engine was beyond the scope of this project. Timken selected the Toyota Avalon with a 3.5L V-6 engine as the test vehicle. In an attempt to minimize cost and fabrication time, a ‘made-from’ approach was proposed in which as many parts as possible would be used or modified from production parts to create the rollerized engine. Timken commissioned its test partner, FEV Engine Technology, to do a feasibility study in which they confirmed that using such an approach was possible to meet the required dimensional restrictions and tolerances. In designing the roller bearing systems for the crank and cam trains, Timken utilized as many production engine parts as possible. The crankshafts were produced from production line forgings, which use Timken steel, modified with special

  4. Roller Cam Positioners

    SciTech Connect

    Bowden, Gordon B.

    2010-12-07

    Roller Cam Positioners could support the LCLS undulator sections allowing micron sized alignment adjustment of each undulator in 5 degrees of freedom. The supports are kinematic with the number of degrees of freedom matched to the number of constraints. Ton loads are supported on simple ball bearings. Motion is intrinsically bounded. Positioning mechanisms are based on pure rolling motion with sub-micron hysteresis and micron resolution. This note describes a general purpose positioning mechanism suitable for undulator support.

  5. Roller belleville spring damper

    SciTech Connect

    Hebel, J.B.

    1981-07-07

    A double acting damper for use in rotary drilling includes a splined tubular telescopic joint and employs plural paralleled stacks of double acting series stacked roller belleville spring washers in an annular pocket between the inner and outer tubular members of the joint. The springs, spline and telescopic bearings are in an oil filled volume sealed from the outside by a pressure seal at the lower end of the damper and a floating seal at the upper end. Electric and magnetic means are provided to check on the condition and quantity of the lubricant.

  6. Temperature distribution and scuffing of tapered roller bearing

    NASA Astrophysics Data System (ADS)

    Wang, Ailin; Wang, Jiugen

    2014-11-01

    In the field of aerospace, high-speed trains and automobile, etc, analysis of temperature filed and scuffing failure of tapered roller bearings are more important than ever, and the scuffing failure of elements of such rolling bearings under heavy load and high speed still cannot be effectively predicted yet. A simplified model of tapered roller bearings consisted of one inner raceway, one outer raceway and a tapered roller was established, in which the interaction of several heat sources is ignored. The contact mechanics model, temperature model and model of scuffing failure are synthesized, and the corresponding computer programs are developed to analyze the effects of bearings parameters, different material and operational conditions on thermal performance of bearings, and temperature distribution and the possibility of surface scuffing are obtained. The results show that load, speed, thermal conductivity and tapered roller materials influence temperature rise and scuffing failure of bearings. Ceramic material of tapered roller results in the decrease of scuffing possibility of bearings to a high extent than the conventional rolling bearing steel. Compared with bulk temperature, flash temperature on the surfaces of bearing elements has a little influence on maximum temperature rise of bearing elements. For the rolling bearings operated under high speed and heavy load, this paper proposes a method which can accurately calculate the possibility of scuffing failure of rolling bearings.

  7. Roller coaster-induced barotrauma.

    PubMed

    Al-Khudari, Samer; Loochtan, Michael; Yaremchuk, Kathleen

    2011-03-01

    We present the case of a 24-year-old male who presented to the otolaryngology clinic for otalgia and aural fullness after riding a roller coaster. We present his clinical course and outcome and briefly discuss the mechanism of injury and otologic barotrauma. Roller coasters have been reported as the cause of many different types of injuries, but this is the first reported case of otologic barotrauma. As the engineering for roller coasters continues to advance in terms of increasing speed, otolaryngologists need to be aware of a new etiology of otologic barotrauma. PMID:21344425

  8. Tolerance Design of Logarithmic Roller Profiles in Cylindrical Roller Bearings

    NASA Astrophysics Data System (ADS)

    Fujiwara, Hiroki; Yamauchi, Kazuto

    A logarithmic profile is essentially optimal crowning geometry for rolling machine elements such as bearing rollers and raceways. Although some design methods of the profile have been proposed, they do not refer to the tolerance of the geometry required in engineering applications and in production. This paper shows how to define the tolerance range associated with the optimum roller profile, previously suggested by one of the authors. The overall tolerance is reasonably defined by giving the reduced amount of roller radius at three points so that the von Mises equivalent stress will not exceed a specified limit, where the point locations are not measured from the roller end but from the intersection of the crowning and the chamfer. For the purpose of design usefulness, the tolerance expression is offered in dimensionless form.

  9. Roller conveyor for a glass furnace

    SciTech Connect

    Ford, J.; Canfield, D.M.

    1986-08-26

    A furnace is described for heat treatment of glass including annealing, heat strengthening, tempering and bending of glass which comprises: a housing defining an elongated furnace chamber having an inlet and an outlet; a roller conveyor between the inlet and the outlet and including respective rows of stub rollers disposed along each longitudinal side of the housing flanking a path between the inlet and the outlet, a lower row of deflecting rollers below one of the rows of stub rollers with the rollers of the lower row being positioned between the stub rollers of the one row, a drive belt being looped over each stub roller of the one row and under each roller of the lower row therebetween, the stub rollers each being provided with at least one band of a heat resistant elastomeric material coating at least a portion of the surface thereof; fused silica support rollers spanning the conveyor with each support roller exclusively upon the respective bands of two stub rollers on each side of the housing, the bands being positioned relative to the belt so as to hold the fused silica support rollers out of engagement with the respective belt; means for driving the belt to oscillate glass objects carried by the support rollers back and forth in the housing; and an array of infrared heaters mounted in the housing at least above the conveyor.

  10. Elasto-plastic contact between rollers

    NASA Astrophysics Data System (ADS)

    Chu, Kunliang; Li, Penghui

    1991-12-01

    Knowledge of the three-dimensional contact stress between roller and rolling road for a strain- hardening material in an elasto-plastic state is limited, to say the least. Mathematical analyses of stress for this problem meet with extreme difficulties. Therefore, experimental approaches are desirable. The experimental elasto-plastic stress analysis method proposed by A. R. Hunter is extended in this investigation. The model material is epoxy resin, which exhibits a frozen nonlinear effective stress-strain behavior similar to that of bearing steel when subjected to a thermal cycle whose maximum temperature is significantly less than the critical temperature of the material. This effective stress-strain curve and an effective birefringence- stress curve were obtained by subjecting uniaxial tensile specimens to constant stress and the appropriate thermal cycle. Then the model was subjected to the same thermal cycle and a uniform distributed load that would develop a plastic zone. The stress distributions on the contact surface and the plastic-zone expansion law were obtained from photomechanical analysis of the slices removed from the model. Several important conclusions were summed up that would greatly improve the roller bearing design.

  11. Principle of reflecting measurement system for roller wear and software simulation

    NASA Astrophysics Data System (ADS)

    Zheng, Longjiang; Wang, Kai; Guo, Yuan; Wang, Yutian

    2006-11-01

    Roller plays an important role in rolling mill. However, the effective surface of roller is limited. After long time working, the surface of roller will wear. The roller wear will result in difficult controlling of shape and thickness of steel board. Further more, it can lead to the decline of product quality. So the measurement of roller wear is very urgent for rolling mill to ensure their product quality. In this paper, a measurement method for roller wear is introduced in detail. This method offers advantages of sensitivity, immediate response, electromagnetic interference, simplicity and non-contact. It can detect in the atrocious condition on-line and examine roller wear precisely and real time. It is an effective method at low cost instance. The basic principle of this system is optical reflection principle. In the paper, after explaining the principle of this measurement system, an error compensation algorithm is exactly calculated to improve accuracy of this measurement system. This algorithm is brought out to offset the shift of measurement track. And a simulation-software program is compiled with Microsoft Visual Basic 6.0 based on this principle. By using this simulation-software, the date of I/O signal for this system is gained. And the signal verse is automatically drawn in this software.

  12. Effect of Roller Profile on Cylindrical Roller Bearing Life Prediction

    NASA Technical Reports Server (NTRS)

    Poplawski, Joseph V.; Zaretsky, Erwin V.; Peters, Steven M.

    2000-01-01

    Four roller profiles used in cylindrical roller bearing design and manufacture were analyzed using both a closed form solution and finite element analysis (FEA) for stress and life. The roller profiles analyzed were flat, tapered end, aerospace, and fully crowned loaded against a flat raceway. Four rolling-element bearing life models were chosen for this analysis and compared. These were those of Weibull, Lundberg and Palmgren, Ioannides and Harris, and Zaretsky. The flat roller profile without edge loading has the longest predicted life. However, edge loading can reduce life by as much as 98 percent. The end tapered profile produced the highest lives but not significantly different than the aerospace profile. The fully crowned profile produces the lowest lives. The resultant predicted life at each stress condition not only depends on the life equation used but also on the Weibull slope assumed. For Weibull slopes of 1.5 and 2, both Lundberg-Palmgren and Iaonnides-Harris equations predict lower lives than the ANSI/ABMAJISO standards. Based upon the Hertz stresses for line contact, the accepted load-life exponent of 10/3 results in a maximum Hertz stress-life exponent equal to 6.6. This value is inconsistent with that experienced in the field.

  13. Stopping a Roller Coaster Train

    ERIC Educational Resources Information Center

    Pendrill, Ann-Marie; Karlsteen, Magnus; Rodjegard, Henrik

    2012-01-01

    A roller coaster ride comes to an end. Magnets on the train induce eddy currents in the braking fins, giving a smooth rise in braking force as the remaining kinetic energy is absorbed by the brakes and converted to thermal energy. In this paper an IR camera was used to monitor the temperature of the first braking fin, before, during and after the…

  14. Free-roller versus fixed-roller fixtures in flexure testing of advanced ceramic materials

    SciTech Connect

    Choi, S.R.; Salem, J.A.

    1996-12-31

    The error associated with strength measurements made with fixed-roller and V-grooved roller fixtures was studied with a variety of roller and fixture material combinations. Both the fixed-roller and the V-grooved fixtures yielded an error in stress of about 4 to 7 %. They also exhibited an appreciable amount of load strain hysteresis. Dynamic fatigue testing of 96 wt % alumina verified the error: the fatigue strength was overestimated by 7 to 9 % for the fixed-roller configuration. The source of error is exclusively attributed to friction between the rollers and the specimen surface, as verified by previous investigators.

  15. 8. DETAIL VIEW OF HEADHOUSE/PIER, SHOWING ROLLER GATE, ROLLER TRACK, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    8. DETAIL VIEW OF HEADHOUSE/PIER, SHOWING ROLLER GATE, ROLLER TRACK, CHAIN, GATE HEATER AND DAM BRIDGE, LOOKING WEST - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 4, Alma, Buffalo County, WI

  16. Effect of Silicon Nitride Balls and Rollers on Rolling Bearing Life

    NASA Technical Reports Server (NTRS)

    Zaretsky, Erwin V.; Vlcek, Brian L.; Hendricks, Robert C.

    2005-01-01

    Three decades have passed since the introduction of silicon nitride rollers and balls into conventional rolling-element bearings. For a given applied load, the contact (Hertz) stress in a hybrid bearing will be higher than an all-steel rolling-element bearing. The silicon nitride rolling-element life as well as the lives of the steel races were used to determine the resultant bearing life of both hybrid and all-steel bearings. Life factors were determined and reported for hybrid bearings. Under nominal operating speeds, the resultant calculated lives of the deep-groove, angular-contact, and cylindrical roller hybrid bearings with races made of post-1960 bearing steel increased by factors of 3.7, 3.2, and 5.5, respectively, from those calculated using the Lundberg-Palmgren equations. An all-steel bearing under the same load will have a longer life than the equivalent hybrid bearing under the same conditions. Under these conditions, hybrid bearings are predicted to have a lower fatigue life than all-steel bearings by 58 percent for deep-groove bearings, 41 percent for angular-contact bearings, and 28 percent for cylindrical roller bearings.

  17. Nanocrystalline, superhard, ductile ceramic coatings for roller-cone bit bearings

    SciTech Connect

    Namavar, F.; Colter, P.; Karimy, H.

    1997-12-31

    The established method for construction of roller bits utilizes carburized steel, frequently with inserted metal bearing surfaces. This construction provides the necessary surface hardness while maintaining other desirable properties in the core. Protective coatings are a logical development where enhanced hardness, wear resistance, corrosion resistance, and surface properties are required. The wear properties of geothermal roller-cone bit bearings could be further improved by application of protective ceramic hard coatings consisting of nanometer-sized crystallites. Nanocrystalline protective coatings provide the required combination of hardness and toughness which has not been available thus far using traditional ceramics having larger grains. Increased durability of roller-cone bit bearings will ultimately reduce the cost of drilling geothermal wells through increased durability.

  18. Influence of Roller Burnishing Parameters on Depletion of Plasticity Reserve

    NASA Astrophysics Data System (ADS)

    Blumenstein, V. Yu; Petrenko, K. P.

    2016-04-01

    Roller burnishing process considerably increases surface quality and service life of machine parts. Efficiency of roller burnishing rises greatly when technological inheritance (TI) is taken into account. Research results of degree of plasticity reserve depletion (DPRD) while roller burnishing are presented. Results obtained made it possible to establish mechanisms of strain accumulation and plasticity reserve depletion according to roller burnishing parameters.

  19. 36 CFR 13.916 - Use of roller skates, skateboards, roller skis, in-line skates, and similar devices.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 36 Parks, Forests, and Public Property 1 2011-07-01 2011-07-01 false Use of roller skates, skateboards, roller skis, in-line skates, and similar devices. 13.916 Section 13.916 Parks, Forests, and..., skateboards, roller skis, in-line skates, and similar devices. The use of roller skates, skateboards,...

  20. 36 CFR 13.916 - Use of roller skates, skateboards, roller skis, in-line skates, and similar devices.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 36 Parks, Forests, and Public Property 1 2012-07-01 2012-07-01 false Use of roller skates, skateboards, roller skis, in-line skates, and similar devices. 13.916 Section 13.916 Parks, Forests, and..., skateboards, roller skis, in-line skates, and similar devices. The use of roller skates, skateboards,...

  1. 36 CFR 13.916 - Use of roller skates, skateboards, roller skis, in-line skates, and similar devices.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 36 Parks, Forests, and Public Property 1 2013-07-01 2013-07-01 false Use of roller skates, skateboards, roller skis, in-line skates, and similar devices. 13.916 Section 13.916 Parks, Forests, and..., skateboards, roller skis, in-line skates, and similar devices. The use of roller skates, skateboards,...

  2. 36 CFR 13.916 - Use of roller skates, skateboards, roller skis, in-line skates, and similar devices.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 36 Parks, Forests, and Public Property 1 2014-07-01 2014-07-01 false Use of roller skates, skateboards, roller skis, in-line skates, and similar devices. 13.916 Section 13.916 Parks, Forests, and..., skateboards, roller skis, in-line skates, and similar devices. The use of roller skates, skateboards,...

  3. Screw-released roller brake

    NASA Technical Reports Server (NTRS)

    Vranish, John M. (Inventor)

    1999-01-01

    A screw-released roller brake including an input drive assembly, an output drive assembly, a plurality of locking sprags, a mechanical tripper nut for unlocking the sprags, and a casing therefor. The sprags consist of three dimensional (3-D) sprag members having pairs of contact surface regions which engage respective pairs of contact surface regions included in angular grooves or slots formed in the casing and the output drive assembly. The sprags operate to lock the output drive assembly to the casing to prevent rotation thereof in an idle mode of operation. In a drive mode of operation, the tripper is either self actuated or motor driven and is translated linearly up and down against a spline and at the limit of its travel rotates the sprags which unlock while coupling the input drive assembly to the output drive assembly so as to impart a turning motion thereto in either a clockwise or counterclockwise direction.

  4. STEEL TRUSS TENSION RING SUPPORTING DOME ROOF. TENSION RING COVERED ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    STEEL TRUSS TENSION RING SUPPORTING DOME ROOF. TENSION RING COVERED BY ARCHITECTURAL FINISH. TENSION RING ROLLER SUPPORT AT COLUMN OBSCURED BY COLUMN COVERINGS. - Houston Astrodome, 8400 Kirby Drive, Houston, Harris County, TX

  5. Unique slider bed eliminates problematic idler rollers

    SciTech Connect

    Not Available

    1988-01-01

    Solidur Plastic's impact slide bed is an innovative solution to problems with idler rollers. The unit provides increased conveyor efficiency and prolonged belt life. It also reduces costly downtime and maintenance needs by eliminating typical idler and conveyor belting problems.

  6. Kidney Stone? Try a Roller Coaster Ride

    MedlinePlus

    ... Space Mountain roller coasters at Orlando's Walt Disney World -- seems to support that view. In the study, Wartinger's group used 3D printing to create a clear silicone model of a kidney that contained urine, plus three ...

  7. Pulmonary hemorrhage resulting from roller coaster.

    PubMed

    Yin, Ming; Tian, Qing; Shen, Hong

    2011-03-01

    Roller coasters are probably one of the more popular rides at amusement parks around the world, and there are few reported injuries. We report a case of symmetric diffuse upper lobe hemorrhage resulting from roller coaster in a previously healthy woman. The clinical course, management, and etiology of her case are discussed; and the literature is reviewed. To our knowledge, pulmonary hemorrhage in this setting has not yet been described. PMID:20825914

  8. Improved oil-off survivability of tapered roller bearings

    NASA Technical Reports Server (NTRS)

    Kreider, Gary E.; Lee, Peter W.

    1987-01-01

    The aim of this program is to improve the oil-off survivability of a tapered roller bearing when applied to a helicopter transmission, since the tapered bearing has shown a performance advantage in this application. However, the critical roller end-rib conjunction is vulnerable to damage in an oil-off condition. Three powdered metal materials were selected to use as the rib material for oil-off evaluation. These were: M2 steel to a 65% density, CBS 1000M 65% density, and CBS 1000M 75% density. The bearing styles tested were ribbed cone (inner race) and ribbed cup (outer race). Carburized solid CBS 600 was also used as a ribbed material for comparison of oil-off results. The tests were conducted at six speeds from 4000 rpm (0.26 million DN) through 37000 rpm (2.4 million DN).The ribbed cup style bearing achieved longer lives than the ribbed cone style. A standard bearing lasted only 10 minutes at 4000 rpm; however, the 30-min oil-off goal was achieved through 11000 rpm using the survivable ribbed cup bearing. The oil-off lives at 37000 rpm were less than 10 seconds. The grinding of the powder metal materials and surface preparation to achieve an open porosity is extremely critical to the oil-off performance of the powder metal component.

  9. Environmental impact studies of Chrome rollers used by cotton roller ginning industries and design and development of pollution free chromeless RCF rollers.

    PubMed

    Singh, Gurdeep; Iyer, G Vijayan

    2004-01-01

    This study focuses on environmental chromium contamination and pollution caused by the use of Chrome Composite Leather-Clad (CCLC) rollers commonly used in cotton roller ginning industries and attempts to eliminate this problem by providing eco-friendly chrome-less rollers.

  10. On Calculation Methods and Results for Straight Cylindrical Roller Bearing Deflection, Stiffness, and Stress

    NASA Technical Reports Server (NTRS)

    Krantz, Timothy L.

    2011-01-01

    The purpose of this study was to assess some calculation methods for quantifying the relationships of bearing geometry, material properties, load, deflection, stiffness, and stress. The scope of the work was limited to two-dimensional modeling of straight cylindrical roller bearings. Preparations for studies of dynamic response of bearings with damaged surfaces motivated this work. Studies were selected to exercise and build confidence in the numerical tools. Three calculation methods were used in this work. Two of the methods were numerical solutions of the Hertz contact approach. The third method used was a combined finite element surface integral method. Example calculations were done for a single roller loaded between an inner and outer raceway for code verification. Next, a bearing with 13 rollers and all-steel construction was used as an example to do additional code verification, including an assessment of the leading order of accuracy of the finite element and surface integral method. Results from that study show that the method is at least first-order accurate. Those results also show that the contact grid refinement has a more significant influence on precision as compared to the finite element grid refinement. To explore the influence of material properties, the 13-roller bearing was modeled as made from Nitinol 60, a material with very different properties from steel and showing some potential for bearing applications. The codes were exercised to compare contact areas and stress levels for steel and Nitinol 60 bearings operating at equivalent power density. As a step toward modeling the dynamic response of bearings having surface damage, static analyses were completed to simulate a bearing with a spall or similar damage.

  11. 12. DETAIL VIEW OF CIRCULAR BRONZE ROLLER GATE POSITION GAUGE, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    12. DETAIL VIEW OF CIRCULAR BRONZE ROLLER GATE POSITION GAUGE, ROLLER GATE PIER HOUSE, TYPE 2A, DAM - Mississippi River 9-Foot Channel Project, Lock & Dam No. 11, Upper Mississippi River, Dubuque, Dubuque County, IA

  12. 49 CFR 215.115 - Defective roller bearing.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Defective roller bearing. 215.115 Section 215.115... § 215.115 Defective roller bearing. (a) A railroad may not place or continue in service a car, if the car has— (1) A roller bearing that shows signs of having been overheated as evidenced by—...

  13. 49 CFR 215.115 - Defective roller bearing.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Defective roller bearing. 215.115 Section 215.115... § 215.115 Defective roller bearing. (a) A railroad may not place or continue in service a car, if the car has— (1) A roller bearing that shows signs of having been overheated as evidenced by—...

  14. 49 CFR 215.117 - Defective roller bearing adapter.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Defective roller bearing adapter. 215.117 Section... Suspension System § 215.117 Defective roller bearing adapter. A railroad may not place or continue in service a car, if the car has a roller bearing adapter that is— (a) Cracked or broken; (b) Not in its...

  15. 49 CFR 215.117 - Defective roller bearing adapter.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Defective roller bearing adapter. 215.117 Section... Suspension System § 215.117 Defective roller bearing adapter. A railroad may not place or continue in service a car, if the car has a roller bearing adapter that is— (a) Cracked or broken; (b) Not in its...

  16. 49 CFR 230.103 - Tender roller bearing journal boxes.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Tender roller bearing journal boxes. 230.103 Section 230.103 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD... Locomotives and Tenders Running Gear § 230.103 Tender roller bearing journal boxes. Tender roller...

  17. 49 CFR 230.103 - Tender roller bearing journal boxes.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Tender roller bearing journal boxes. 230.103 Section 230.103 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD... Locomotives and Tenders Running Gear § 230.103 Tender roller bearing journal boxes. Tender roller...

  18. 49 CFR 230.103 - Tender roller bearing journal boxes.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Tender roller bearing journal boxes. 230.103 Section 230.103 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD... Locomotives and Tenders Running Gear § 230.103 Tender roller bearing journal boxes. Tender roller...

  19. 49 CFR 230.103 - Tender roller bearing journal boxes.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Tender roller bearing journal boxes. 230.103 Section 230.103 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD... Locomotives and Tenders Running Gear § 230.103 Tender roller bearing journal boxes. Tender roller...

  20. 49 CFR 215.117 - Defective roller bearing adapter.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Defective roller bearing adapter. 215.117 Section... Suspension System § 215.117 Defective roller bearing adapter. A railroad may not place or continue in service a car, if the car has a roller bearing adapter that is— (a) Cracked or broken; (b) Not in its...

  1. 49 CFR 215.115 - Defective roller bearing.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Defective roller bearing. 215.115 Section 215.115... § 215.115 Defective roller bearing. (a) A railroad may not place or continue in service a car, if the car has— (1) A roller bearing that shows signs of having been overheated as evidenced by—...

  2. 49 CFR 215.115 - Defective roller bearing.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Defective roller bearing. 215.115 Section 215.115... § 215.115 Defective roller bearing. (a) A railroad may not place or continue in service a car, if the car has— (1) A roller bearing that shows signs of having been overheated as evidenced by—...

  3. 49 CFR 215.115 - Defective roller bearing.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Defective roller bearing. 215.115 Section 215.115... § 215.115 Defective roller bearing. (a) A railroad may not place or continue in service a car, if the car has— (1) A roller bearing that shows signs of having been overheated as evidenced by—...

  4. 49 CFR 215.117 - Defective roller bearing adapter.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Defective roller bearing adapter. 215.117 Section... Suspension System § 215.117 Defective roller bearing adapter. A railroad may not place or continue in service a car, if the car has a roller bearing adapter that is— (a) Cracked or broken; (b) Not in its...

  5. 49 CFR 215.117 - Defective roller bearing adapter.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Defective roller bearing adapter. 215.117 Section... Suspension System § 215.117 Defective roller bearing adapter. A railroad may not place or continue in service a car, if the car has a roller bearing adapter that is— (a) Cracked or broken; (b) Not in its...

  6. 49 CFR 230.103 - Tender roller bearing journal boxes.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Tender roller bearing journal boxes. 230.103... Locomotives and Tenders Running Gear § 230.103 Tender roller bearing journal boxes. Tender roller bearing journal boxes shall be maintained in a safe and suitable condition....

  7. 29 CFR 1918.63 - Chutes, gravity conveyors and rollers.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 7 2011-07-01 2011-07-01 false Chutes, gravity conveyors and rollers. 1918.63 Section 1918... Equipment Other Than Ship's Gear § 1918.63 Chutes, gravity conveyors and rollers. (a) Chutes shall be of... and gravity conveyor roller sections shall be firmly placed and secured to prevent...

  8. 29 CFR 1918.63 - Chutes, gravity conveyors and rollers.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 7 2014-07-01 2014-07-01 false Chutes, gravity conveyors and rollers. 1918.63 Section 1918... Equipment Other Than Ship's Gear § 1918.63 Chutes, gravity conveyors and rollers. (a) Chutes shall be of... and gravity conveyor roller sections shall be firmly placed and secured to prevent...

  9. 29 CFR 1918.63 - Chutes, gravity conveyors and rollers.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Chutes, gravity conveyors and rollers. 1918.63 Section 1918... Equipment Other Than Ship's Gear § 1918.63 Chutes, gravity conveyors and rollers. (a) Chutes shall be of... and gravity conveyor roller sections shall be firmly placed and secured to prevent...

  10. 29 CFR 1918.63 - Chutes, gravity conveyors and rollers.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 7 2012-07-01 2012-07-01 false Chutes, gravity conveyors and rollers. 1918.63 Section 1918... Equipment Other Than Ship's Gear § 1918.63 Chutes, gravity conveyors and rollers. (a) Chutes shall be of... and gravity conveyor roller sections shall be firmly placed and secured to prevent...

  11. 28. Photocopy of Crown Roller Mill illustration; originally published in ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    28. Photocopy of Crown Roller Mill illustration; originally published in The Crown Roller Mill, Northwestern Miller 9 (May 21, 1880): 321; SHOWING WEST SIDE, LOOKING EAST - Crown Roller Mill, 105 Fifth Avenue, South, West Side Milling District, Minneapolis, Hennepin County, MN

  12. Magnetostrictive Roller-Drive Stepping Motor

    NASA Technical Reports Server (NTRS)

    Vranish, John M.

    1993-01-01

    Proposed motor based on magnetostrictive effect provides stepped angular motion with angular increments of order of 100 microradians. Driven to repeat stepping cycle rapidly enough to achieve maximum speed of about 20 rpm, provides torque an order of magnitude greater than electric motors, and brakes itself when power turned off. Magnetostrictive rods in electromagnet coils push against drive plate, causing it to rotate slightly. This slight rotation jams conical rollers between cam surfaces on outer drive ring and split drum, so rollers transmit rotation to drum. Suitable for precise, high-torque, fail-safe-braking, direct drive of robot joint, without bulk and weight of additional brake mechanism and gear train.

  13. Large-bore tapered-roller bearing performance and endurance to 2.4 million DN

    NASA Technical Reports Server (NTRS)

    Parker, R. J.

    1983-01-01

    The operating characteristics and experimental life estimates for 120.65 mm bore tapered roller bearings of two designs under combined radial and thrust loads were determined. A modified standard bearing design was tested at speeds up to 15,000 rpm. A computer optimized, high speed design was tested at speeds up to 20,000 rpm. Both designs were tested at a combined load of 26,700 N (6000 lb) radial load and and 53,400 N (12,000 lb) thrust load. Advanced helicopter transmissions which require the higher-speed capability of tapered-roller bearings also require higher temperature capability (ref. 2). Thus, materials with temperature capabilities higher than the conventional carburizing steels are required.

  14. Designing Drops, Loops, and Hills: The Physics behind Roller Coaster Design

    NASA Astrophysics Data System (ADS)

    Christiana, Katharyn; Ilie, Carolina

    2013-03-01

    Almost everyone has seen a roller coaster at one time in their life. They range in type from old wooden coasters from decades passes to modern machines made of steel that allow you to stand up while riding. The basic physics behind these machines is relatively simple, but in the modern world we strive to design bigger and better machines that push the human body and the laws of physics to their limits. But how do the designers of these rides maintain the balance between making riders feel like they're on the brink of death while keeping them completely safe? The answer can be found in basic physics and mechanical engineering. This is a part of the honors thesis that focuses on the mechanical principles applied in roller coaster design. The theoretical part of the thesis will be complemented by a full small scale ride design.

  15. Remote Sensing Characteristics of Wave Breaking Rollers

    NASA Astrophysics Data System (ADS)

    Haller, M. C.; Catalan, P.

    2006-12-01

    The wave roller has a primary influence on the balances of mass and momentum in the surf zone (e.g. Svendsen, 1984; Dally and Brown, 1995; Ruessink et al., 2001). In addition, the roller area and its angle of inclination on the wave front are important quantities governing the dissipation rates in breaking waves (e.g Madsen et al., 1997). Yet, there have been very few measurements published of individual breaking wave roller geometries in shallow water. A number of investigators have focused on observations of the initial jet-like motion at the onset of breaking before the establishment of the wave roller (e.g. Basco, 1985; Jansen, 1986), while Govender et al. (2002) provide observations of wave roller vertical cross-sections and angles of inclination for a pair of laboratory wave conditions. Nonetheless, presently very little is known about the growth, evolution, and decay of this aerated region of white water as it propagates through the surf zone; mostly due to the inherent difficulties in making the relevant observations. The present work is focused on analyzing observations of the time and space scales of individual shallow water breaking wave rollers as derived from remote sensing systems. Using a high-resolution video system in a large-scale laboratory facility, we have obtained detailed measurements of the growth and evolution of the wave breaking roller. In addition, by synchronizing the remote video with in-situ wave gages, we are able to directly relate the video intensity signal to the underlying wave shape. Results indicate that the horizontal length scale of breaking wave rollers differs significantly from the previous observations of Duncan (1981), which has been a traditional basis for roller model parameterizations. The overall approach to the video analysis is new in the sense that we concentrate on individual breaking waves, as opposed to the more commonly used time-exposure technique. In addition, a new parameter of interest, denoted Imax, is

  16. Help for the Steel Industry

    NASA Technical Reports Server (NTRS)

    1991-01-01

    A collaboration between NASA Lewis Research Center (LRC) and Gladwin Engineering resulted in the adaptation of aerospace high temperature metal technology to the continuous casting of steel. The continuous process is more efficient because it takes less time and labor. A high temperature material, once used on the X-15 research plane, was applied to metal rollers by a LRC developed spraying technique. Lewis Research Center also supplied mold prototype of metal composites, reducing erosion and promoting thermal conductivity. Rollers that previously cracked due to thermal fatigue, lasted longer. Gladwin's sales have increased, and additional NASA-developed innovations are anticipated.

  17. Roller compaction of moist pharmaceutical powders.

    PubMed

    Wu, C-Y; Hung, W-L; Miguélez-Morán, A M; Gururajan, B; Seville, J P K

    2010-05-31

    The compression behaviour of powders during roller compaction is dominated by a number of factors, such as process conditions (roll speed, roll gap, feeding mechanisms and feeding speed) and powder properties (particle size, shape, moisture content). The moisture content affects the powder properties, such as the flowability and cohesion, but it is not clear how the moisture content will influence the powder compression behaviour during roller compaction. In this study, the effect of moisture contents on roller compaction behaviour of microcrystalline cellulose (MCC, Avicel PH102) was investigated experimentally. MCC samples of different moisture contents were prepared by mixing as-received MCC powder with different amount of water that was sprayed onto the powder bed being agitated in a rotary mixer. The flowability of these samples were evaluated in terms of the poured angle of repose and flow functions. The moist powders were then compacted using the instrumented roller compactor developed at the University of Birmingham. The flow and compression behaviour during roller compaction and the properties of produced ribbons were examined. It has been found that, as the moisture content increases, the flowability of moist MCC powders decreases and the powder becomes more cohesive. As a consequence of non-uniform flow of powder into the compaction zone induced by the friction between powder and side cheek plates, all produced ribbons have a higher density in the middle and lower densities at the edges. For the ribbons made of powders with high moisture contents, different hydration states across the ribbon width were also identified from SEM images. Moreover, it was interesting to find that these ribbons were split into two halves. This is attributed to the reduction in the mechanical strength of moist powder compacts with high moisture contents produced at high compression pressures.

  18. Roller compaction of moist pharmaceutical powders.

    PubMed

    Wu, C-Y; Hung, W-L; Miguélez-Morán, A M; Gururajan, B; Seville, J P K

    2010-05-31

    The compression behaviour of powders during roller compaction is dominated by a number of factors, such as process conditions (roll speed, roll gap, feeding mechanisms and feeding speed) and powder properties (particle size, shape, moisture content). The moisture content affects the powder properties, such as the flowability and cohesion, but it is not clear how the moisture content will influence the powder compression behaviour during roller compaction. In this study, the effect of moisture contents on roller compaction behaviour of microcrystalline cellulose (MCC, Avicel PH102) was investigated experimentally. MCC samples of different moisture contents were prepared by mixing as-received MCC powder with different amount of water that was sprayed onto the powder bed being agitated in a rotary mixer. The flowability of these samples were evaluated in terms of the poured angle of repose and flow functions. The moist powders were then compacted using the instrumented roller compactor developed at the University of Birmingham. The flow and compression behaviour during roller compaction and the properties of produced ribbons were examined. It has been found that, as the moisture content increases, the flowability of moist MCC powders decreases and the powder becomes more cohesive. As a consequence of non-uniform flow of powder into the compaction zone induced by the friction between powder and side cheek plates, all produced ribbons have a higher density in the middle and lower densities at the edges. For the ribbons made of powders with high moisture contents, different hydration states across the ribbon width were also identified from SEM images. Moreover, it was interesting to find that these ribbons were split into two halves. This is attributed to the reduction in the mechanical strength of moist powder compacts with high moisture contents produced at high compression pressures. PMID:20176096

  19. Effect of roller shapes on strip buckling in a continuous annealing furnace

    NASA Astrophysics Data System (ADS)

    Yang, Jing; Tang, Di; Su, Lan; Jiang, Hai-Tao; Yang, Quan

    2011-06-01

    The effect of roller shapes on strip buckling in a continuous annealing furnace was focused on. The tensile stress distribution, the transverse compressive stress, and the critical buckling stress of the strip were studied by the finite element method (FEM) when the flat roller, crown roller, single taper roller, and double taper roller were used, respectively. Simulation results show that strip buckling is most likely to occur with the crown roller, then the double taper roller, and finally the single taper roller. Also, strip buckling can not occur when the flat roller is used. Considering strip snaking, the single taper roller and double taper roller are suggested in the continuous annealing furnace. The double taper roller with a better strip snaking-prevention ability should be applied in the sections with high strip temperature, and the single taper roller with a better buckling-prevention ability should be used in the sections with low strip temperature.

  20. Feasibility study of a discrete bearing/roller drive rotary joint for the space station

    NASA Technical Reports Server (NTRS)

    Loewenthal, S. H.; Schuller, F. T.

    1986-01-01

    The most critical mechanism on board the proposed space station is the continously rotating joint which must accurately align the solar power units with the sun during earth orbit. The feasibility of a multiple, discrete bearing supported joint driven by a self-loading, pinch drive actuator was investigated for this application. This concept appears to offer greater protection against catastrophic jamming, less sensitivity to adverse thermal gradients, greater accessibility to inorbit servicing or replacement and greater adaptability to very large (5 m) truss members than to more conventional continuous support bearing/gear reducer joints. Analytical trade studies performed herein establish that a discrete cam roller bearing support system having eight hangers around a continuous ring would provide sufficient radial and bending stiffness to prevent any degradation in the fundamental frequencies of the solar wing structure. Furthermore, it appears that the pinch roller drive mechanism can be readily sized to meet or exceed system performance and service life requirements. Wear life estimates based on experimental data for a steel roller coated with an advanced polyimide film show a continuous service life more than two orders of magnitude greater than required for this application.

  1. Rollers smell the fear of nestlings.

    PubMed

    Parejo, D; Amo, L; Rodríguez, J; Avilés, J M

    2012-08-23

    Many animals react to danger by producing chemical cues that can be smelled by others, which is called the smell of fear. Some bird species produce chemical compounds when threatened, such as nestlings of the Eurasian roller Coracias garrulus that vomit an odorous orange liquid when scared in their nests. Here, we experimentally explore the possibility that parents were informed about recent predation attempts at their nests through the olfaction of this vomit. Parents of nests treated with nestling vomit delayed their entrance to nests and decreased their provisioning rate in comparison with parents of nests treated with an odorous control. These results demonstrate that adult rollers are able to smell the fear of offspring and show for the first time in birds that a scent produced during an interspecific challenge has a role in an intraspecific communication scenario.

  2. Interference Fit Life Factors for Roller Bearings

    NASA Technical Reports Server (NTRS)

    Oswald, Fred B.; Zaretsky, Erwin V.; Poplawski, Joseph V.

    2008-01-01

    The effect of hoop stresses in reducing cylindrical roller bearing fatigue life was determined for various classes of inner ring interference fit. Calculations were performed for up to seven interference fit classes for each of ten bearing sizes. Each fit was taken at tightest, average and loosest values within the fit class for RBEC-5 tolerance, thus requiring 486 separate analyses. The hoop stresses were superimposed on the Hertzian principal stresses created by the applied radial load to calculate roller bearing fatigue life. The method was developed through a series of equations to calculate the life reduction for cylindrical roller bearings based on interference fit. All calculated lives are for zero initial bearing internal clearance. Any reduction in bearing clearance due to interference fit was compensated by increasing the initial (unmounted) clearance. Results are presented as tables and charts of life factors for bearings with light, moderate and heavy loads and interference fits ranging from extremely light to extremely heavy and for bearing accuracy class RBEC 5 (ISO class 5). Interference fits on the inner bearing ring of a cylindrical roller bearing can significantly reduce bearing fatigue life. In general, life factors are smaller (lower life) for bearings running under light load where the unfactored life is highest. The various bearing series within a particular bore size had almost identical interference fit life factors for a particular fit. The tightest fit at the high end of the RBEC-5 tolerance band defined in ANSI/ABMA shaft fit tables produces a life factor of approximately 0.40 for an inner-race maximum Hertz stress of 1200 MPa (175 ksi) and a life factor of 0.60 for an inner-race maximum Hertz stress of 2200 MPa (320 ksi). Interference fits also impact the maximum Hertz stress-life relation.

  3. Kinematic stability of roller pairs in free rolling contact

    NASA Technical Reports Server (NTRS)

    Savage, M.; Loewenthal, S. H.

    1976-01-01

    A set of generalized stability equations was developed for roller pairs in free rolling contact. A symmetric, dual contact model was used. Four possible external contact profiles that possess continuous contacting surfaces were studied. It was found that kinematic stability would be insured if the larger radius of transverse curvature, in absolute value, and the smaller rolling radius both exist on the roller that has the apex of its conical surface outboard of its main body. The stability criteria developed are considered to be useful for assessing axial restraint requirements for a variety of roller mechanisms and in the selection of roller contact geometry for traction drive devices.

  4. Eco-friendly rubberized cotton fabric roller for ginning machines.

    PubMed

    Iyer, G V

    2007-01-01

    This article discusses the pollution caused by chrome composite leather-clad (CCLC) rollers commonly used in cotton roller ginning mills and suggests an alternative roller material. CCLC rollers contain about 18,000 to 36,000 mg/kg (ppm) total chromium in trivalent and hexavalent forms, which are toxic to human health and carcinogenic. When seed-cotton is processed in double roller (DR) ginning machines, the lint is contaminated with chromium, and chromium particles are carried into the spun yarns and cotton by-products. Specifically, due to persistent rubbing of the leather-clad roller over the stationary knife during the ginning process, the lint is contaminated with about 140 to 1990 ppm of chromium, and the spun yarns and cotton by-products contain about 100 to 200 ppm, far in excess of the standard limit of 0.1 ppm. Gin and mill workers are directly exposed to this carcinogenic substance. To offset this problem, pollution-free rubberized cotton fabric (RCF) rollers have been fabricated and tested in roller gins. The RCF roller covering is made of multiple layers of fabric bonded together using a white rubber compound, which has a surface finish conducive to high ginning efficiency. This eliminates chromium contamination and pollution during the ginning process. On the basis of the design and development of various test rollers and subsequent evaluation studies, the performance of pollution-free RCF rollers has been demonstrated with reference to their commercial benefit and eco-friendliness in cotton ginning mills.

  5. Sensing roller for in-process thickness measurement

    DOEpatents

    Novak, J.L.

    1996-07-16

    An apparatus and method are disclosed for processing materials by sensing roller, in which the sensing roller has a plurality of conductive rings (electrodes) separated by rings of dielectric material. Sensing capacitances or impedances between the electrodes provides information on thicknesses of the materials being processed, location of wires therein, and other like characteristics of the materials. 6 figs.

  6. Sensing roller for in-process thickness measurement

    DOEpatents

    Novak, James L.

    1996-01-01

    An apparatus and method for processing materials by sensing roller, in which the sensing roller has a plurality of conductive rings (electrodes) separated by rings of dielectric material. Sensing capacitances or impedances between the electrodes provides information on thicknesses of the materials being processed, location of wires therein, and other like characteristics of the materials.

  7. Head motions while riding roller coasters: implications for brain injury.

    PubMed

    Pfister, Bryan J; Chickola, Larry; Smith, Douglas H

    2009-12-01

    The risk of traumatic brain injury (TBI) while riding roller coasters has received substantial attention. Case reports of TBI around the time of riding roller coasters have led many medical professionals to assert that the high gravitational forces (G-forces) induced by roller coasters pose a significant TBI risk. Head injury research, however, has shown that G-forces alone cannot predict TBI. Established head injury criterions and procedures were employed to compare the potential of TBI between daily activities and roller coaster riding. Three-dimensional head motions were measured during 3 different roller coaster rides, a pillow fight, and car crash simulations. Data was analyzed and compared with published data, using similar analyses of head motions. An 8.05 m/s car crash lead to the largest head injury criterion measure of 28.1 and head impact power of 3.41, over 6 times larger than the roller coaster rides of 4.1 and 0.36. Notably, the linear and rotational components of head acceleration during roller coaster rides were milder than those induced by many common activities. As such, there appears to be an extremely low risk of TBI due to the head motions induced by roller coaster rides. PMID:19901817

  8. On the Stability of a Bicycle on Rollers

    ERIC Educational Resources Information Center

    Cleary, Patricia A.; Mohazzabi, Pirooz

    2011-01-01

    Riding a bicycle on the newest form of indoor training, rollers, presents a unique experiment on bicycle stability. The stability factors eliminated by riding on rollers are discussed in terms of refined handling and control of the centre of mass on a bicycle. This paper is intended for undergraduate physics majors as well as any other general…

  9. Head motions while riding roller coasters: Implications for brain injury

    PubMed Central

    Chickola, Larry; Smith, Douglas H.

    2009-01-01

    The risk of traumatic brain injury (TBI) while riding roller coasters has received substantial attention. Case reports of TBI around the time of riding roller coasters have led many medical professionals to assert that the high gravitational forces (G-forces) induced by roller coasters pose a significant TBI risk. Head injury research, however, has shown that G-forces alone cannot predict TBI. Established head injury criterions and procedures were employed to compare the potential of TBI between daily activities and roller coaster riding. Three dimensional head motions were measured during three different roller coaster rides, a pillow fight, and car crash simulations. Data was analyzed and compared to published data using similar analyses of head motions. An 8.05m/s car crash lead to the largest head injury criterion measure (HIC15) of 28.1 and head impact factor (HIP) of 3.41, over six times larger than the roller coaster rides of 4.1 and 0.36. Notably, the linear and rotational components of head acceleration during roller coaster rides were milder than those induced by many common activities. As such, there appears to be an extremely low risk of TBI due to the head motions induced by roller coaster rides. PMID:19901817

  10. Roller coaster related fatalities, United States, 1994–2004

    PubMed Central

    Pelletier, A; Gilchrist, J

    2005-01-01

    Objective: To determine the number of fatalities related to roller coasters and examine factors common to multiple incidents. Methods: A case was defined as the death of a person, which was associated with a roller coaster in the United States between 15 May 1994 and 14 May 2004. Cases were identified from four data sources: (1) Consumer Product Safety Commission, (2) Lexis-Nexis, (3) Medline, and (4) Saferparks. Results: Forty people, ranging in age from 7 to 77 years, were killed in 39 separate incidents. Twenty nine (73%) deaths occurred among roller coaster patrons. Eleven fatalities resulted from external causes related to injuries from falls or collisions. Eighteen people died from medical conditions that might have been caused or exacerbated by riding a roller coaster; 15 were the result of intracranial hemorrhages or cardiac problems. Eleven (28%) deaths involved employees; all were caused by injuries. Conclusions: Approximately four deaths annually in the United States are associated with roller coasters. Prevention of roller coaster fatalities is dependent on establishing an effective surveillance system for amusement ride injuries, engineering rides to better protect both patrons and employees, improving training and supervision of employees regarding safety precautions, and posting cautionary notices near roller coasters for people with specified medical conditions. Further research is needed on roller coaster related deaths resulting from intracranial hemorrhages and cardiac problems. PMID:16203841

  11. Neurologic complication after a roller coaster ride.

    PubMed

    Sa Leitao, Davi; Mendonca, Dercio; Iyer, Harish; Kao, Cheng-Kai

    2012-01-01

    Neurologic complications after roller coaster rides are uncommon but potentially catastrophic. Physicians should have a high index of suspicion and prompt appropriate investigation. A 22-year-old healthy African American man presented with a 2-day history of constant occipital headache associated with vertigo, nausea, vomiting, and ambulatory dysfunction. Physical examination showed gait ataxia, slight dysmetria, and vertical nystagmus. Magnetic resonance imaging (MRI) of the brain showed early subacute ischemic infarct in the right cerebellum in the distribution of the right posterior inferior cerebellar artery. Magnetic resonance angiography of the neck showed focal dissection of the right vertebral artery at C1 through C2 level. On subsequent questioning, the patient recollected riding a roller coaster 2 weeks before the onset of symptoms. Anticoagulation with heparin was started, and the patient was bridged to oral warfarin. After a 5-day uneventful hospital course, symptoms improved and patient was discharged on oral anticoagulation. Cervicocephalic arterial dissections after roller coaster rides are rarely described in literature. The acceleration and abrupt changes of direction might lead to indirect trauma that is applied to mobile portions of the cervicocephalic arteries leading to intimal tears. Magnetic resonance angiography combined with axial T1-weighted cervical MRI is preferred because it is a high-sensitive, noninvasive test. The rationale for the use of anticoagulants or antiplatelets in patients with cervicocephalic arterial dissection is to prevent early recurrence and infarction. However, a meta-analysis failed to show significant difference in the rates of disability or death between both groups. Therefore, the decision for medical treatment should be made in a case-by-case basis. PMID:20980120

  12. Lateral Stability Simulation of a Rail Truck on Roller Rig

    NASA Astrophysics Data System (ADS)

    Dukkipati, Rao V.

    The development of experimental facilities for rail vehicle testing is being complemented by analytic studies. The purpose of this effort has been to gain insight into the dynamics of rail vehicles in order to guide development of the Roller Rigs and to establish an analytic framework for the design and interpretation of tests to be conducted on Roller Rigs. The work described here represents initial efforts towards meeting these objectives. Generic linear models were developed of a freight car (with a characteristic North American three-piece truck) on tangent track. The models were developed using the generalized multi body dynamics software MEDYNA. Predictions were made of the theoretical linear model hunting (lateral stability) characteristics of the freight car, i. e., the critical speeds and frequencies, for five different configurations: (a) freight car on track, (b) the freight car's front truck on the roller stand and its rear truck on track, (c) freight car on the roller rig, (d) a single truck on track, and (e) single truck on the roller stand. These were compared with the Association of American Railroads' field test data for an 80-ton hopper car equipped with A-3 ride control trucks. Agreement was reached among all the analytical models, with all models indicating a range of hunting speeds of 2% from the highest to lowest. The largest discrepancy, approximately 6%, was indicated between the models and the field test data. Parametric study results using linear model of freight truck on the roller rig show that (a) increasing roller radius increases critical speed (b) increasing the wheel initial cone angle will decrease the hunting speed (c) increasing the roller cant increases hunting speed (d) decrowning of the wheelset on the rollers will not effect the hunting speed but induces longitudinal destabilizing horizontal forces at the contact and (e) lozenging of wheelset on the rollers induces a yaw moment and the hunting speed decreases with increasing

  13. 36 CFR 13.916 - Use of roller skates, skateboards, roller skis, in-line skates, and similar devices.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Regulations-Denali National Park and Preserve General Provisions § 13.916 Use of roller skates... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Use of roller...

  14. 21 CFR 870.4370 - Roller-type cardiopulmonary bypass blood pump.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Roller-type cardiopulmonary bypass blood pump. 870... Roller-type cardiopulmonary bypass blood pump. (a) Identification. A roller-type cardiopulmonary bypass blood pump is a device that uses a revolving roller mechanism to pump the blood through...

  15. 21 CFR 870.4370 - Roller-type cardiopulmonary bypass blood pump.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Roller-type cardiopulmonary bypass blood pump. 870... Roller-type cardiopulmonary bypass blood pump. (a) Identification. A roller-type cardiopulmonary bypass blood pump is a device that uses a revolving roller mechanism to pump the blood through...

  16. 21 CFR 870.4370 - Roller-type cardiopulmonary bypass blood pump.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Roller-type cardiopulmonary bypass blood pump. 870... Roller-type cardiopulmonary bypass blood pump. (a) Identification. A roller-type cardiopulmonary bypass blood pump is a device that uses a revolving roller mechanism to pump the blood through...

  17. 21 CFR 870.4370 - Roller-type cardiopulmonary bypass blood pump.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Roller-type cardiopulmonary bypass blood pump. 870... Roller-type cardiopulmonary bypass blood pump. (a) Identification. A roller-type cardiopulmonary bypass blood pump is a device that uses a revolving roller mechanism to pump the blood through...

  18. System for automatically aligning a support roller system under a rotating body

    DOEpatents

    Singletary, B.H.

    1982-07-21

    Two support rings on a rotatable drum respectively engage conically tapered end surfaces of support rollers mounted on pivot universally relative to its axis of rotation and translate therealong. Rotation of the drum on differential conical support roller diameters causes pivotal steering and axial translation of support roller until roller is centered on support rings.

  19. System for automatically aligning a support roller system under a rotating body

    DOEpatents

    Singletary, B. Huston

    1983-01-01

    Two support rings on a rotatable drum respectively engage conically tapered nd surfaces of support rollers mounted on pivot universally relative to its axis of rotation and translate therealong. Rotation of the drum on differential conical support roller diameters causes pivotal steering and axial translation of support roller until roller is centered on support rings.

  20. Dragline roller track improvement. Volume I. Evaluation of low hardness dragline track materials in rolling contact. Final report, September 30, 1976-July 30, 1980

    SciTech Connect

    Dunfee, J.; Leonard, L.; Rumbarger, J.

    1980-01-01

    The Franklin Research Center (FRC), a Division of the Franklin Institute, was contracted by the Bureau of Mines to improve walking dragline roller tracks. The contract was subsequently transferred to the Department of Energy. The period from September 1977 to September 1978 covered laboratory rolling contact rig tests to evaluate typical low hardness dragline track materials. The results of this work are covered by DOE/ET/9121-1 Final Report, Volume I. The period from September 1978 to July 1980 covered field measurements of dragline roller circle loadings. The results of this work are covered by DOE/ET/9121-2 Final Report, Volume II. The laboratory rolling contact rig test results indicate that forged vacuum degassed air melt steel materials are recommended over air-melt cast materials for rollers and tracks. The steels tested exhibited good freedom from sensitivity to stress raisers like brinell marks and small holes or discontinuities (Volume I). The largest unknown in a recommended method for life testing roller tracks is the condition of the upper rotating frame structure and the lower tub supporting structure.

  1. Development of small bore, high speed tapered roller bearing

    NASA Technical Reports Server (NTRS)

    Morrison, F. R.; Gassel, S. S.; Bovenkerk, R. L.

    1981-01-01

    The performance of four rolling bearing configurations for use on the input pinion shaft of a proposed commercial helicopter transmission was evaluated. The performance characteristics of a high speed tapered roller bearing operating under conditions comparable to those existing at this input pinion shaft were defined. The tapered roller bearing shaft support configuration was developed for the gearbox using commercially available bearing designings. The configuration was optimized and interactive thermomechanically system analyzed. Automotive pinion quality tapered roller bearings were found to be reliable under load and speed conditions in excess of those anticipated in the helicopter transmission. However, it is indicated that the elastohydrodynamic lubricant films are inadequate.

  2. Chronic subdural haematoma after riding a roller coaster.

    PubMed

    Yamakami, Iwao; Mine, Seiichiro; Yamaura, Akira; Fukutake, Toshio

    2005-01-01

    We report a 20-year-old man who developed a chronic subdural haematoma (CSDH) after riding a "giant" roller coaster. The patient had a past history of a subdural hygroma, diagnosed six weeks after a motorcycle accident. Three months after this accident, he rode on a roller coaster, but suffered no direct head trauma during the ride. Three weeks later, he developed a CSDH requiring surgical evacuation. Roller coaster riding, associated with high velocities and extreme acceleration/deceleration forces is a modern cause of CSDH in the young, which may be increasing due to ever-faster rides. PMID:15639420

  3. 30. Elevator no. 3: top floor, rollers for southeast conveyor ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    30. Elevator no. 3: top floor, rollers for southeast conveyor belt flanked by top openings of grain bins, with tripper in background, facing northeast - Washburn Crosby Company Elevators No. 2 & 3, 900 & 1000 Second Avenue, South, Minneapolis, Hennepin County, MN

  4. 29. Elevator no. 3: top floor, conveyor belt rollers for ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    29. Elevator no. 3: top floor, conveyor belt rollers for belt to gangway (in background) connecting with elevator no. 2, facing northwest - Washburn Crosby Company Elevators No. 2 & 3, 900 & 1000 Second Avenue, South, Minneapolis, Hennepin County, MN

  5. 7. DETAIL VIEW OF DAM, SHOWING ROLLER GATES, GATE PIERS, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    7. DETAIL VIEW OF DAM, SHOWING ROLLER GATES, GATE PIERS, HEADHOUSES AND DAM BRIDGE, LOOKING NORTHWEST, UPSTREAM - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 9, Lynxville, Crawford County, WI

  6. 26. VIEW OF ROLLER GATE BULKHEADS AND BULKHEAD CARS IN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    26. VIEW OF ROLLER GATE BULKHEADS AND BULKHEAD CARS IN STORAGE YARD, WITH DAM BRIDGE OVERHEAD, LOOKING SOUTHEAST - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 9, Lynxville, Crawford County, WI

  7. 5. DETAIL VIEW OF DAM, SHOWING ROLLER AND TAINTER GATES, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    5. DETAIL VIEW OF DAM, SHOWING ROLLER AND TAINTER GATES, GATE PIERS, HEADHOUSES AND DAM BRIDGE, LOOKING NORTHWEST, UPSTREAM - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 9, Lynxville, Crawford County, WI

  8. Engine testing of ceramic cam-roller followers. Final report

    SciTech Connect

    Kalish, Y.

    1992-04-01

    For several years, DDC has been developing monolithic ceramic heat engine components. One of the components, developed for an application in our state-of-the-art on-highway, heavy-duty diesel engine, the Series 60, is a silicon nitride cam-roller follower. Prior to starting this program, each valve train component in the Series 60 was considered for conversion to a ceramic material. Many advantages and disadvantages (benefits and risks) were considered. From this effort, one component was selected, the cam-roller follower. Using a system design approach, a ceramic cam-roller follower offered functional improvement at a reasonable cost. The purpose of the project was to inspect and test 100 domestically produced silicon nitride cam-roller followers built to the requirements of the DDC series 60 engine.

  9. Engine testing of ceramic cam-roller followers

    SciTech Connect

    Kalish, Y. )

    1992-04-01

    For several years, DDC has been developing monolithic ceramic heat engine components. One of the components, developed for an application in our state-of-the-art on-highway, heavy-duty diesel engine, the Series 60, is a silicon nitride cam-roller follower. Prior to starting this program, each valve train component in the Series 60 was considered for conversion to a ceramic material. Many advantages and disadvantages (benefits and risks) were considered. From this effort, one component was selected, the cam-roller follower. Using a system design approach, a ceramic cam-roller follower offered functional improvement at a reasonable cost. The purpose of the project was to inspect and test 100 domestically produced silicon nitride cam-roller followers built to the requirements of the DDC series 60 engine.

  10. 14. INTERIOR VIEW OF HEADHOUSE, SHOWING ROLLER GATE GAUGE AND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. INTERIOR VIEW OF HEADHOUSE, SHOWING ROLLER GATE GAUGE AND WHEEL GEAR, LOOKING SOUTHEAST - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 8, On Mississippi River near Houston County, MN, Genoa, Vernon County, WI

  11. Design and Realization Of Roller Mill Control System

    NASA Astrophysics Data System (ADS)

    Wang, QianHong; Zhang, Qiang; Bai, XiaoLi; Yu, HongLiang

    a Distributed Control System(DCS) of cement raw materials is presented for the vertical roller mill by the application of ABB's IndustrialIT. The results demonstrate the practical application of the system's utility and effectiveness and reliability.

  12. 25. VIEW OF ROLLER GATE BULKHEADS, WITH BULKHEAD CARS AND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    25. VIEW OF ROLLER GATE BULKHEADS, WITH BULKHEAD CARS AND TRACKS IN STORAGE YARD, WITH DAM BRIDGE OVERHEAD, LOOKING EAST - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 4, Alma, Buffalo County, WI

  13. 3. DETAIL VIEW OF DAM, SHOWING ROLLER AND TAINTER GATES, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. DETAIL VIEW OF DAM, SHOWING ROLLER AND TAINTER GATES, GATE PIERS, HEADHOUSES AND DAM BRIDGES, LOOKING SOUTH, DOWNSTREAM - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 4, Alma, Buffalo County, WI

  14. 17. Detail showing roller nest for vertical strut sitting atop ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    17. Detail showing roller nest for vertical strut sitting atop granite pier cap. View to southwest. - Selby Avenue Bridge, Spanning Short Line Railways track at Selby Avenue between Hamline & Snelling Avenues, Saint Paul, Ramsey County, MN

  15. GENERAL VIEW OF EAST SIDE LOOKING WEST, ROLLER DAM AND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    GENERAL VIEW OF EAST SIDE LOOKING WEST, ROLLER DAM AND RURAL ELECTRICAL FACILITY IN FOREGROUND AND CURRENT HIGHWAY 151 BRIDGE IN BACKGROUND. - Wapsipinicon River Bridge, Spanning Wapsipinicon River at former State Highway 151, Anamosa, Jones County, IA

  16. 15. VIEW OF NORTHWEST BEARING SEAT WITH EXPANSION ROLLERS ON ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    15. VIEW OF NORTHWEST BEARING SEAT WITH EXPANSION ROLLERS ON NORTHERN PIER; FACING SOUTHEAST. - Walker Bridge, Spanning Klamath River and connecting Highway 96 and Walker Road, Klamath River, Siskiyou County, CA

  17. 18. VIEW OF ROLLER LEVELER USED TO STRAIGHTEN AND FLATTEN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    18. VIEW OF ROLLER LEVELER USED TO STRAIGHTEN AND FLATTEN METAL SHEETS. (7/2/86) - Rocky Flats Plant, Uranium Rolling & Forming Operations, Southeast section of plant, southeast quadrant of intersection of Central Avenue & Eighth Street, Golden, Jefferson County, CO

  18. 26. Detail view of drum girder with rollers below, resting ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    26. Detail view of drum girder with rollers below, resting on fixed turntable upon masonry center pier. Swing drive shaft (vertical) is turned by level gear of horizontal shaft (protruding through machine room wall), which turns pinion gear toothed to fixed turntable rack below rollers. (Nov. 25, 1988) - University Heights Bridge, Spanning Harlem River at 207th Street & West Harlem Road, New York County, NY

  19. A study on rheological characteristics of roller milled fenugreek fractions.

    PubMed

    Sakhare, Suresh D; Inamdar, Aashitosh A; Prabhasankar, P

    2016-01-01

    Fenugreek seeds were fractionated by roller milling to get various fractions. The roller milled fractions and whole fenugreek flour (WFF) were evaluated for the flow behavior and time-dependent flow properties using a rotational viscometer at the temperatures of 10-60 (0)C. The samples subjected to a programmed shear rate increase linearly from 0 to 300 s(-1) in 3 min and successive decrease linearly shear rate from 300 s(-1) to 0 in 3 min. The roller milled fractions and WFF paste exhibited non-Newtonian pseudoplastic behavior. Difference in hysteresis loop area was observed among the roller milled fractions and WFF, being more noticeable at lower temperatures. Power law and Casson models were used to predict flow properties of samples. The power law model described well the flow behavior of the roller milled fractions and WFF at temperatures tested. Except flour (FL) fraction, consistency coefficient, m, increased with the temperature both in the forward and backward measurements. The roller milled fractions and WFF exhibited rheopectic behavior that increased viscosity with increasing the shear speed and the temperature. For all the sample tested, initial shear stress increased with increase in shear rate and temperature. PMID:26787961

  20. Spherical roller bearing analysis. SKF computer program SPHERBEAN. Volume 1: Analysis

    NASA Technical Reports Server (NTRS)

    Kleckner, R. J.; Pirvics, J.

    1980-01-01

    The models and associated mathematics used within the SPHERBEAN computer program for prediction of the thermomechanical performance characteristics of high speed lubricated double row spherical roller bearings are presented. The analysis allows six degrees of freedom for each roller and three for each half of an optionally split cage. Roller skew, free lubricant, inertial loads, appropriate elastic and friction forces, and flexible outer ring are considered. Roller quasidynamic equilibrium is calculated for a bearing with up to 30 rollers per row, and distinct roller and flange geometries are specifiable. The user is referred to the material contained here for formulation assumptions and algorithm detail.

  1. Holland Roller Windmill: investigation and demonstration of principles. Final report

    SciTech Connect

    Holland, R. Jr.

    1981-06-01

    A horizontal axis wind power machine using a radially positioned spinning cylindrical roller was investigated and a demonstration machine was constructed and operated in the natural wind. Earlier wind machines using the Magnus rotor were reviewed, such as the Flettner Rotor Windmill and the Madaras Rotor Power Plant. Wind tunnel tests and analyses were made. Analyses were made of gyroscopic bending moments on the roller and centrifugal hinge moments acting on the freely hinged trailer. Analyses of applied structural air loads were made of the conventional torsionally restrained airfoil type blade compared to the unconventional blade consisting of roller and free trailer. Criteria for stress analysis of trailer blades were developed. Exploratory wind tunnel tests were made of the downwash patterns around Magnus rotors. The power required to spin them was measured. Combined spinning and whirling of a model horizontal axis roller machine was demonstrated. Tests of blade type models were run. Sections for roller mill blades, consisting of power driven spinning roller and a series of trailers of varying sizes and shapes, were tested. Reynolds number effects on section performance were studied, and broadly suitable types of roller trailer combinations were determined below the critical and above the critical Reynolds. A design was synthesized for a single bladed demonstrator machine, including stress analysis, detail design, construction and assembly. The demonstrator operated satisfactorily in the natural wind. Results indicate that major benefits of this type of machine are virtual elimination of stresses due to gusts and strong winds, and marked reduction of cost per unit of swept disk area.

  2. Innovative Design to Prevent Reversal of Roller Blood Pump Rotation in the Event of Electromechanical Failure: An Easy Solution to a Devastating Problem

    PubMed Central

    Skoletsky, Jennifer S.; White, Brian T.; Austin, Jon W.

    2007-01-01

    Abstract: Despite the advanced technologies of battery back-up for heart-lung consoles and the availability of system-wide generators, electromechanical failure is still occurring. Several heartlung machine manufacturers still provide unsafe handcranking devices to use in the case of an emergency while using a roller blood pump. A new design has been engineered to eliminate safety and quality issues for the perfusionist and the patient when the need for handcranking presents itself. A ratchet-style handcranking device was fabricated by means of a steel plate with adjustable pins. The adjustable pins allow for use with different models of the Cobe, Stockert, and Jostra heart-lung consoles, which contain roller pumps with 180° roller heads. Additional modifications such as a 1:2 transmission and fluorescent markers are also used in the design. This innovative design is an improvement in safety compared with the current handcrank provided by Cobe, Stockert, and Jostra. With this modified handcranking device, accidental reverse rotation of the roller pump head cannot occur. Fluorescent markers will improve visualization of the pump head in low-light situations. The ergonomic design improves efficiency by reducing fatigue. Most importantly, a “safe” safety device will replace the current design provided by these manufacturers, thus improving the quality of care by health care providers. PMID:17672191

  3. Innovative design to prevent reversal of roller blood pump rotation in the event of electromechanical failure: an easy solution to a devastating problem.

    PubMed

    Skoletsky, Jennifer S; White, Brian T; Austin, Jon W

    2007-06-01

    Despite the advanced technologies of battery back-up for heart-lung consoles and the availability of system-wide generators, electromechanical failure is still occurring. Several heart-lung machine manufacturers still provide unsafe handcranking devices to use in the case of an emergency while using a roller blood pump. A new design has been engineered to eliminate safety and quality issues for the perfusionist and the patient when the need for handcranking presents itself. A ratchet-style handcranking device was fabricated by means of a steel plate with adjustable pins. The adjustable pins allow for use with different models of the Cobe, Stockert, and Jostra heart-lung consoles, which contain roller pumps with 1800 roller heads. Additional modifications such as a 1:2 transmission and fluorescent markers are also used in the design. This innovative design is an improvement in safety compared with the current handcrank provided by Cobe, Stockert, and Jostra. With this modified handcranking device, accidental reverse rotation of the roller pump head cannot occur. Fluorescent markers will improve visualization of the pump head in low-light situations. The ergonomic design improves efficiency by reducing fatigue. Most importantly, a "safe" safety device will replace the current design provided by these manufacturers, thus improving the quality of care by health care providers.

  4. 48 CFR 225.7009 - Restriction on ball and roller bearings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Restriction on ball and roller bearings. 225.7009 Section 225.7009 Federal Acquisition Regulations System DEFENSE ACQUISITION... roller bearings....

  5. 48 CFR 225.7009 - Restriction on ball and roller bearings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Restriction on ball and roller bearings. 225.7009 Section 225.7009 Federal Acquisition Regulations System DEFENSE ACQUISITION... roller bearings....

  6. 48 CFR 225.7009 - Restriction on ball and roller bearings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Restriction on ball and roller bearings. 225.7009 Section 225.7009 Federal Acquisition Regulations System DEFENSE ACQUISITION... roller bearings....

  7. 48 CFR 225.7009 - Restriction on ball and roller bearings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 3 2014-10-01 2014-10-01 false Restriction on ball and roller bearings. 225.7009 Section 225.7009 Federal Acquisition Regulations System DEFENSE ACQUISITION... roller bearings....

  8. 48 CFR 225.7009 - Restriction on ball and roller bearings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Restriction on ball and roller bearings. 225.7009 Section 225.7009 Federal Acquisition Regulations System DEFENSE ACQUISITION... roller bearings....

  9. Pressure pulsation in roller pumps: a validated lumped parameter model.

    PubMed

    Moscato, Francesco; Colacino, Francesco M; Arabia, Maurizio; Danieli, Guido A

    2008-11-01

    During open-heart surgery roller pumps are often used to keep the circulation of blood through the patient body. They present numerous key features, but they suffer from several limitations: (a) they normally deliver uncontrolled pulsatile inlet and outlet pressure; (b) blood damage appears to be more than that encountered with centrifugal pumps. A lumped parameter mathematical model of a roller pump (Sarns 7000, Terumo CVS, Ann Arbor, MI, USA) was developed to dynamically simulate pressures at the pump inlet and outlet in order to clarify the uncontrolled pulsation mechanism. Inlet and outlet pressures obtained by the mathematical model have been compared with those measured in various operating conditions: different rollers' rotating speed, different tube occlusion rates, and different clamping degree at the pump inlet and outlet. Model results agree with measured pressure waveforms, whose oscillations are generated by the tube compression/release mechanism during the rollers' engaging and disengaging phases. Average Euclidean Error (AEE) was 20mmHg and 33mmHg for inlet and outlet pressure estimates, respectively. The normalized AEE never exceeded 0.16. The developed model can be exploited for designing roller pumps with improved performances aimed at reducing the undesired pressure pulsation.

  10. Evaluation of Wear between Pin and Bush in Roller Chain

    NASA Astrophysics Data System (ADS)

    Noguchi, Shoji; Yoshiba, Hideaki; Nakayama, Satoshi; Kanada, Tohru

    A roller chain is a typical machine element used in bicycles, motorcycles and many other devices for power transmission. The life of a roller chain is determined by elongation. As a rule of thumb, a chain begins to skip cogs on the sprocket wheel when the percentage of elongation reaches approximately 3%. Mechanical wear between pins and bushes causes elongation of the roller chain. However, research on the evaluation of wear of the roller chain is rare and the achievement is unstated. We describe the following initiatives in the study of wear between pins and bushes of a roller chain: (1) development of a wear tester using only two chain links, (2) establishment of a specific evaluation method using a roundness tester, and (3) causal explanation of non-uniform wear using the finite-element method (FEM). The experimental results show that pins and bushes are not in contact at the centerline, and that wear occurs exclusively at the tips of the pins owing to the bending deformation under the condition of tensile load.

  11. Net efficiency of roller skiing with a diagonal stride.

    PubMed

    Nakai, Akira; Ito, Akira

    2011-02-01

    The aims of this study were: (a) to determine net efficiency during roller skiing with a diagonal stride at various speeds; (b) to assess the development of net efficiency across speeds; and (c) to examine the characteristics of efficiency in diagonal roller skiing. Two-dimensional kinematics and oxygen uptake were determined in eight male collegiate cross-country ski athletes who roller skied with the diagonal stride at various speeds on a level track. Net efficiency was calculated from rates of internal and external work and net energy expenditure. Individual net efficiency ranged from 17.7% to 52.1%. Net efficiency in the entire group of athletes increased with increasing speed, reached a maximum value of 37.3% at 3.68 m · s(-1), before slowly decreasing. These findings indicate that roller skiing with the diagonal stride at high speed is a highly efficient movement and that an optimal speed exists at which net efficiency can be maximally enhanced in diagonal roller skiing.

  12. 48 CFR 252.225-7016 - Restriction on acquisition of ball and roller bearings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... of ball and roller bearings. 252.225-7016 Section 252.225-7016 Federal Acquisition Regulations System... and roller bearings. As prescribed in 225.7009-5, use the following clause: RESTRICTION ON ACQUISITION OF BALL AND ROLLER BEARINGS (JUN 2011) (a) Definitions. As used in this clause— (1) Bearing...

  13. 48 CFR 252.225-7016 - Restriction on acquisition of ball and roller bearings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... of ball and roller bearings. 252.225-7016 Section 252.225-7016 Federal Acquisition Regulations System... and roller bearings. As prescribed in 225.7009-5, use the following clause: Restriction on Acquisition of Ball and Roller Bearings (MAR 2006) (a) Definitions. As used in this clause' (1)...

  14. 48 CFR 252.225-7016 - Restriction on acquisition of ball and roller bearings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... of ball and roller bearings. 252.225-7016 Section 252.225-7016 Federal Acquisition Regulations System... and roller bearings. As prescribed in 225.7009-5, use the following clause: Restriction on Acquisition of Ball and Roller Bearings (JUN 2011) (a) Definitions. As used in this clause— (1) Bearing...

  15. 48 CFR 252.225-7016 - Restriction on acquisition of ball and roller bearings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... of ball and roller bearings. 252.225-7016 Section 252.225-7016 Federal Acquisition Regulations System... and roller bearings. As prescribed in 225.7009-5, use the following clause: Restriction on Acquisition of Ball and Roller Bearings (JUN 2011) (a) Definitions. As used in this clause— (1) Bearing...

  16. 48 CFR 252.225-7016 - Restriction on acquisition of ball and roller bearings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... of ball and roller bearings. 252.225-7016 Section 252.225-7016 Federal Acquisition Regulations System... and roller bearings. As prescribed in 225.7009-5, use the following clause: Restriction on Acquisition of Ball and Roller Bearings (JUN 2011) (a) Definitions. As used in this clause— (1) Bearing...

  17. 21 CFR 870.4370 - Roller-type cardiopulmonary bypass blood pump.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Roller-type cardiopulmonary bypass blood pump. 870... Roller-type cardiopulmonary bypass blood pump. (a) Identification. A roller-type cardiopulmonary bypass... cardiopulmonary bypass circuit during bypass surgery. (b) Classification. Class II (performance standards)....

  18. Evolution of a Hybrid Roller Cone/PDC core bit

    SciTech Connect

    Pettitt, R.; Laney, R.; George, D.; Clemens, G.

    1980-01-01

    The development of the hot dry rock (HDR) geothermal resource, as presently being accomplished by the Los Alamos Scientific Laboratory (LASL), requires that sufficient quantities of good quality core be obtained at a reasonable cost. The use of roller cone core bits, with tungsten carbide inserts, was initiated by the Deep Sea Drilling Program. These bits were modified for continental drilling in deep, hot, granitic rock for the LASL HDR Geothermal Site at Fenton Hill, New Mexico in 1974. After the advent of monocrystalline diamond Stratapax pads, a prototype hybrid roller cone/Stratapax core bit was fabricated by Smith Tool, and tested at Fenton Hill in 1978. During the drilling for a deeper HDR reservoir system in 1979 and 1980, six of the latest generation of these bits, now called Hybrid Roller Cone/Polycrystalline Diamond Cutter (PDC) core bits, were successfully used in granitic rock at depths below 11,000 ft.

  19. Analysis of roller hemming process for a vehicle tailgate closure

    NASA Astrophysics Data System (ADS)

    Gürgen, Selim; Gökler, Mustafa İlhan; Darendeliler, Haluk; Çelikkaya, Çetin Cengiz; Erden, Kemal

    2013-05-01

    Hemming is a sheet metal joining process which is widely used for vehicle closures. As the latest hemming process type, the roller hemming process uses industrial robots therefore; main advantage of the process is achieved as flexibility with improved product quality. Trial and error method is the general approach to design the process in the industry due to limited know-how in the roller hemming. However, due to advantages of the process, the recent studies have also been focused on numerical simulations. In this study, the roller hemming process of the tailgate of a vehicle has been investigated by using the finite element method. The points of interest are selected as cycle time reduction and reducing the undesired wrinkling formation in the process. In the current roller hemming process of the tailgate, three stages including two pre-hemming and one final hemming stages are being applied. For the cycle time reduction, simulations have been performed to complete the hemming process in two stages. Effects of the roller geometry and the bending angle pairs have been investigated. The hemming process with two stages has been shown numerically to be applicable by considering the final geometry of the product and the maximum stress and strain values occurred during the process. The wrinkling formation is reduced by using a roller with larger diameter in the simulations. Then, verifications of the simulations have been done by implementing of the process. As a result of the study, approximately 33% reduction in the cycle time and 50% increase in the productivity of the tailgate have been successfully achieved in addition to reduction in the wrinkling formation during the pre-hemming stage.

  20. Dropping a particle out of a roller coaster

    NASA Astrophysics Data System (ADS)

    Mungan, Carl E.; Lipscombe, Trevor C.

    2014-07-01

    A rider in a roller coaster lets go of a particle such as a small marble. How far does the marble travel horizontally from the point of release before hitting the ground, assuming the speed of the roller coaster is determined by conservation of mechanical energy starting from the highest hill up which it was pulled? Where should the marble be released along the track if one wishes to maximize the range of the marble? These questions constitute interesting variations on conventional problems in two-dimensional kinematics, appropriate for an undergraduate course in classical mechanics. Exploration of various shapes of tracks could form interesting student projects for numerical or experimental investigation.

  1. Rollers in low-head dams - Challenges and solutions

    NASA Astrophysics Data System (ADS)

    Zamankhan, Piroz

    2012-12-01

    Low-head dams exist in many rivers for the purposes of diverting water for open-channel irrigation and providing power plants with cooling water. Flow over low-head dams is quite complex and dangerous rollers often develop down-stream that tend to trap and submerge floating objects. This paper presents an analysis of the problem based on physical and computational fluid dynamics (CFD) modeling and the result of this analysis in the form of design suggestions intended to diminish the hazards associated with rollers.

  2. TUBE FLANGING APPARATUS HAVING SPIRAL CAM ACTUATED FLANGING ROLLERS

    DOEpatents

    Bellarts, H.J.

    1958-06-24

    A tube flaring apparatus designed to roll flawless uniform flanges on tube ends suitable for use in a Van Stone joint is described. Tapered rollers are mounted on gear segnnents and placed in the end of the tube. The assembly is rotated axially within the tube, and periodically the gear segments are moved by a worm gear so as to force the rollers radially against the tube wall until eventually a perfect 90 d flange is formed on the tube. All flanges formed by this machine are uniform, stronger, and have fewer possibilities for leaks than conventional methods heretofore used.

  3. Roller-gear drives for robotic manipulators design, fabrication and test

    NASA Technical Reports Server (NTRS)

    Anderson, William J.; Shipitalo, William

    1991-01-01

    Two single axis planetary roller-gear drives and a two axis roller-gear drive with dual inputs were designed for use as robotic transmissions. Each of the single axis drives is a two planet row, four planet arrangement with spur gears and compressively loaded cylindrical rollers acting in parallel. The two axis drive employs bevel gears and cone rollers acting in parallel. The rollers serve a dual function: they remove backlash from the system, and they transmit torque when the gears are not fully engaged.

  4. 26. Elevator no. 2: floor 4, rollers for south conveyor ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    26. Elevator no. 2: floor 4, rollers for south conveyor belt, showing top openings of grain bins on floor, with bin number on ceiling above, facing east - Washburn Crosby Company Elevators No. 2 & 3, 900 & 1000 Second Avenue, South, Minneapolis, Hennepin County, MN

  5. 24. Elevator no. 2: floor 4, turnhead distributor and rollers ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    24. Elevator no. 2: floor 4, turnhead distributor and rollers for south conveyor belt; east and south walls of control room (floor 5) in background; facing northeast - Washburn Crosby Company Elevators No. 2 & 3, 900 & 1000 Second Avenue, South, Minneapolis, Hennepin County, MN

  6. Tapered Roller Bearing Damage Detection Using Decision Fusion Analysis

    NASA Technical Reports Server (NTRS)

    Dempsey, Paula J.; Kreider, Gary; Fichter, Thomas

    2006-01-01

    A diagnostic tool was developed for detecting fatigue damage of tapered roller bearings. Tapered roller bearings are used in helicopter transmissions and have potential for use in high bypass advanced gas turbine aircraft engines. A diagnostic tool was developed and evaluated experimentally by collecting oil debris data from failure progression tests conducted using health monitoring hardware. Failure progression tests were performed with tapered roller bearings under simulated engine load conditions. Tests were performed on one healthy bearing and three pre-damaged bearings. During each test, data from an on-line, in-line, inductance type oil debris sensor and three accelerometers were monitored and recorded for the occurrence of bearing failure. The bearing was removed and inspected periodically for damage progression throughout testing. Using data fusion techniques, two different monitoring technologies, oil debris analysis and vibration, were integrated into a health monitoring system for detecting bearing surface fatigue pitting damage. The data fusion diagnostic tool was evaluated during bearing failure progression tests under simulated engine load conditions. This integrated system showed improved detection of fatigue damage and health assessment of the tapered roller bearings as compared to using individual health monitoring technologies.

  7. New seed-cotton reclaimer for high speed roller gins

    Technology Transfer Automated Retrieval System (TEKTRAN)

    An experimental laboratory prototype reclaimer is being developed by the USDA-ARS in cooperation with Lummus Corporation. The objective of the project is to develop a seed-cotton reclaimer for high speed roller ginning that has a higher operational capacity and reduced seed loss in comparison to cur...

  8. View of east side with large sliding door, rollers, and ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of east side with large sliding door, rollers, and tracks to large x-ray room - U.S. Naval Base, Pearl Harbor, Industrial X-Ray Building, Off Sixth Street, adjacent to and south of Facility No. 11, Pearl City, Honolulu County, HI

  9. 16. Detail showing roller nest between granite pier cap and ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    16. Detail showing roller nest between granite pier cap and moveable end of truss at east end of main spans. View to southeast. - Selby Avenue Bridge, Spanning Short Line Railways track at Selby Avenue between Hamline & Snelling Avenues, Saint Paul, Ramsey County, MN

  10. The Physics of the Roller Coaster: Learning Physics through Simulation.

    ERIC Educational Resources Information Center

    Hannum, Wallace

    2001-01-01

    This instructional design blends a structured learning environment (the physics lesson) with an engaging, playful, simulated environment (roller coaster construction), putting into operation ideas from both cognitive and constructivist theories. Two instructional models are used: a general design model for creating instruction and a lesson design…

  11. 9. VIEW OF MOLTEN SALT BATH EQUIPMENT AND ROLLER PRESSES ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    9. VIEW OF MOLTEN SALT BATH EQUIPMENT AND ROLLER PRESSES BEING INSTALLED ON THE WEST SIDE (SIDE B) OF BUILDING 883. SIDE B OF BUILDING 883 WAS USED TO PROCESS ENRICHED URANIUM FROM 1957-66. (1/23/57) - Rocky Flats Plant, Uranium Rolling & Forming Operations, Southeast section of plant, southeast quadrant of intersection of Central Avenue & Eighth Street, Golden, Jefferson County, CO

  12. Bead Roller, at right, used for preparing flume sheeting (still ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Bead Roller, at right, used for preparing flume sheeting (still in use, 2004); on left is a pipe cutter. Facing southeast - Childs-Irving Hydroelectric Project, Childs System, Childs Powerhouse, Forest Service Road 708/502, Camp Verde, Yavapai County, AZ

  13. Measurement of transferable chemical residue from nylon carpet using the California roller and a new mega-California roller.

    PubMed

    Williams, Ryan L; Bernard, Craig E; Dyk, Melinda Bigelow; Ross, John H; Krieger, Robert I

    2008-11-01

    Human chemical exposures resulting from transfer of surface deposition on indoor nylon carpets may be estimated by measuring transferable residues (mu g chemical/cm2 carpet). A weighted roller developed at California Department of Food and Agriculture (CDFA) has been extensively used to sample transferable residue for estimates of human exposure in risk characterization. A modified roller has been developed to evaluate the influence of pressure on transferable chemical residue since weight and force (or pressure, kg/m2) may vary person-to-person and activity-to-activity. A 30.5 cm diameter roller was used to apply 60 to 2100 kg/m2 to bracket pressures exerted by humans on a flat nylon-carpeted surface. Measurements of transferable cyfluthrin residues were made after 1, 7, and 21 days. Total Soxhlet extractable cyfluthrin residues were relatively constant during the test period. Residue transferability decreased during the study period. Modest increases in the transferability of surface residues were observed over the broad range of pressures applied by the modified roller.

  14. Study of rolling element dynamic interactions with separators and raceway paths: Roller to separator contact forces and cage to shaft speed ratios in roller bearings

    NASA Technical Reports Server (NTRS)

    Nypan, L. J.

    1978-01-01

    Cage to roller force measurements, cage to shaft forces, and cage to shaft speed ratios are reported for 115 and 118mm bore roller bearings operating at speeds of 4,000, 8,000, and 12,000 rpm under loads ranging from 360 to 6670 N (80 to 1500 lb).

  15. A scaled roller test rig for high-speed vehicles

    NASA Astrophysics Data System (ADS)

    Allotta, Benedetto; Pugi, Luca; Malvezzi, Monica; Bartolini, Fabio; Cangioli, Francesco

    2010-12-01

    Scaled roller rigs are quite widespread among railway research centres, and several examples are described in the literature. Due to their low costs and ease of use compared with full-scale counterparts, these types of rigs are used for a wide range of studies concerning dynamical stability, comfort, mechatronic subsystem and wear. Furthermore, scaled roller rigs can be a powerful education tool for railway engineering students. In this paper, the design and the main features of the scaled rolled rig that will be installed in the Mechatronics and Dynamic Modeling Laboratory of the University of Florence located in Pistoia, Italy, are described. The main feature of the proposed rig will be the simulation of degraded adhesion conditions. This feature is very important for hardware-in-the loop testing of many safety relevant on-board subsystems like wheel slide protection systems, traction and stability controls, odometry and automatic train protection and control.

  16. Student investigations of the forces in a roller coaster loop

    NASA Astrophysics Data System (ADS)

    Pendrill, Ann-Marie

    2013-11-01

    How does the experience of a riding in a roller coaster loop depend on your position in the train? This question has been investigated by first year engineering physics students by using multiple representations of force and motion. Theoretical considerations for a circular loop show that the differences between the forces on a rider in the front, middle or back of the train depend on the ratio between train length and radius of the loop, which can be estimated from a photograph. Numerical computations complement the analysis of a video clip, accelerometer data, and measurements of the time needed for the train to move over the highest point. A roller coaster ride gives striking examples of Newton's laws applied to your own body, and demonstrates that the experience depends on the vector character of velocity and acceleration.

  17. Flow and roller array interaction at low Reynolds numbers

    NASA Astrophysics Data System (ADS)

    Sheikh, Zubair M.; Wang, Lipo; Zhang, Qiang

    2016-06-01

    Differing from the conventional no-slip wall boundary condition, the moving surface may have strong influences on the flow structures and the flow physics. Such effects are potentially important and useful for flow control. In this paper we analyze the two-dimensional flow over a roller array with different spacing and rotating speeds at the low Reynolds numbers. The numerical results indicate that the pressure drag and the friction drag of the rollers are strongly dependent on flowing and geometric parameters. Physically, surface motion can induce the viscous traction stream, which leads to very important effects, such as the so called impingement block and traction stream flush. These interesting findings may help to better understand the fluid dynamics for the general moving boundary cases.

  18. Pin and roller attachment system for ceramic blades

    DOEpatents

    Shaffer, J.E.

    1995-07-25

    In a turbine, a plurality of blades are attached to a turbine wheel by way of a plurality of joints which form a rolling contact between the blades and the turbine wheel. Each joint includes a pin and a pair of rollers to provide rolling contact between the pin and an adjacent pair of blades. Because of this rolling contact, high stress scuffing between the blades and the turbine wheel reduced, thereby inhibiting catastrophic failure of the blade joints. 3 figs.

  19. Pin and roller attachment system for ceramic blades

    DOEpatents

    Shaffer, James E.

    1995-01-01

    In a turbine, a plurality of blades are attached to a turbine wheel by way of a plurality of joints which form a rolling contact between the blades and the turbine wheel. Each joint includes a pin and a pair of rollers to provide rolling contact between the pin and an adjacent pair of blades. Because of this rolling contact, high stress scuffing between the blades and the turbine wheel reduced, thereby inhibiting catastrophic failure of the blade joints.

  20. Interference-Fit Life Factors for Roller Bearings

    NASA Technical Reports Server (NTRS)

    Oswald, Fred B.; Zaretsky, Erwin V.; Poplawski, Joseph V.

    2009-01-01

    The effect of hoop stresses in reducing cylindrical roller bearing fatigue life was determined for various classes of inner-ring interference fit. Calculations were performed for up to 7 fit classes for each of 10 bearing sizes. The hoop stresses were superimposed on the Hertzian principal stresses created by the applied radial load to calculate roller bearing fatigue life. A method was developed through a series of equations to calculate the life reduction for cylindrical roller bearings. All calculated lives are for zero initial internal clearance. Any reduction in bearing clearance due to interference fit would be compensated by increasing the initial (unmounted) clearance. Results are presented as tables and charts of life factors for bearings with light, moderate, and heavy loads and interference fits ranging from extremely light to extremely heavy for bearing accuracy class RBEC-5 (ISO class 5). Interference fits on the inner ring of a cylindrical roller bearing can significantly reduce bearing fatigue life. In general, life factors are smaller (lower life) for bearings running under light load where the unfactored life is highest. The various bearing series within a particular bore size had almost identical interference-fit life factors for a particular fit. The tightest fit at the high end of the tolerance band produces a life factor of approximately 0.40 for an inner-race maximum Hertz stress of 1200 MPa (175 ksi) and a life factor of 0.60 for an inner-race maximum Hertz stress of 2200 MPa (320 ksi). Interference fits also impact the maximum Hertz stress-life relation.

  1. Salmonella transfer during pilot plant scale washing and roller conveying of tomatoes.

    PubMed

    Wang, Haiqiang; Ryser, Elliot T

    2014-03-01

    Salmonella transfer during washing and roller conveying of inoculated tomatoes was quantified using a pilot scale tomato packing line equipped with plastic, foam, or brush rollers. Red round tomatoes (2.3 kg) were dip inoculated with Salmonella enterica serovar Typhimurium LT2 (avirulent) (4 log CFU/g), air dried for 2 h, and then washed in sanitizer-free water for 2 min. Inoculated tomatoes were then passed single file over a 1.5-m conveyor equipped with plastic, foam, or brush rollers followed by 25 previously washed uninoculated tomatoes. Tomato samples were collected after 2 min of both washing and roller conveying, with all 25 uninoculated tomatoes collected individually after conveying. Roller surface samples were collected before and after conveying the uninoculated tomatoes. Both tomato and surface samples were quantitatively examined for Salmonella by direct plating or membrane filtration using xylose lysine Tergitol 4 agar. Regardless of the roller type, Salmonella populations on inoculated tomatoes did not significantly (P < 0.05) decrease during contact with the roller conveyors. After conveying uninoculated tomatoes over contaminated foam rollers, 96% of the 25 tomatoes were cross-contaminated with Salmonella at >100 CFU per tomato. With plastic rollers, 24 and 76% of tomatoes were cross-contaminated with Salmonella at 10 to 100 and 1 to 10 CFU per tomato, respectively. In contrast, only 8% of 25 tomatoes were cross-contaminated with brush rollers with Salmonella populations of 1 to 10 CFU per tomato. Overall, cross-contamination was greatest with foam, followed by plastic and brush rollers (P < 0.05). Adding peroxyacetic acid or chlorine to the wash water significantly decreased cross-contamination during tomato conveying, with chlorine less effective in controlling Salmonella on foam compared with plastic and brush rollers. PMID:24674428

  2. Salmonella transfer during pilot plant scale washing and roller conveying of tomatoes.

    PubMed

    Wang, Haiqiang; Ryser, Elliot T

    2014-03-01

    Salmonella transfer during washing and roller conveying of inoculated tomatoes was quantified using a pilot scale tomato packing line equipped with plastic, foam, or brush rollers. Red round tomatoes (2.3 kg) were dip inoculated with Salmonella enterica serovar Typhimurium LT2 (avirulent) (4 log CFU/g), air dried for 2 h, and then washed in sanitizer-free water for 2 min. Inoculated tomatoes were then passed single file over a 1.5-m conveyor equipped with plastic, foam, or brush rollers followed by 25 previously washed uninoculated tomatoes. Tomato samples were collected after 2 min of both washing and roller conveying, with all 25 uninoculated tomatoes collected individually after conveying. Roller surface samples were collected before and after conveying the uninoculated tomatoes. Both tomato and surface samples were quantitatively examined for Salmonella by direct plating or membrane filtration using xylose lysine Tergitol 4 agar. Regardless of the roller type, Salmonella populations on inoculated tomatoes did not significantly (P < 0.05) decrease during contact with the roller conveyors. After conveying uninoculated tomatoes over contaminated foam rollers, 96% of the 25 tomatoes were cross-contaminated with Salmonella at >100 CFU per tomato. With plastic rollers, 24 and 76% of tomatoes were cross-contaminated with Salmonella at 10 to 100 and 1 to 10 CFU per tomato, respectively. In contrast, only 8% of 25 tomatoes were cross-contaminated with brush rollers with Salmonella populations of 1 to 10 CFU per tomato. Overall, cross-contamination was greatest with foam, followed by plastic and brush rollers (P < 0.05). Adding peroxyacetic acid or chlorine to the wash water significantly decreased cross-contamination during tomato conveying, with chlorine less effective in controlling Salmonella on foam compared with plastic and brush rollers.

  3. Roller compaction: Effect of relative humidity of lactose powder.

    PubMed

    Omar, Chalak S; Dhenge, Ranjit M; Palzer, Stefan; Hounslow, Michael J; Salman, Agba D

    2016-09-01

    The effect of storage at different relative humidity conditions, for various types of lactose, on roller compaction behaviour was investigated. Three types of lactose were used in this study: anhydrous lactose (SuperTab21AN), spray dried lactose (SuperTab11SD) and α-lactose monohydrate 200M. These powders differ in their amorphous contents, due to different manufacturing processes. The powders were stored in a climatic chamber at different relative humidity values ranging from 10% to 80% RH. It was found that the roller compaction behaviour and ribbon properties were different for powders conditioned to different relative humidities. The amount of fines produced, which is undesirable in roller compaction, was found to be different at different relative humidity. The minimum amount of fines produced was found to be for powders conditioned at 20-40% RH. The maximum amount of fines was produced for powders conditioned at 80% RH. This was attributed to the decrease in powder flowability, as indicated by the flow function coefficient ffc and the angle of repose. Particle Image Velocimetry (PIV) was also applied to determine the velocity of primary particles during ribbon production, and it was found that the velocity of the powder during the roller compaction decreased with powders stored at high RH. This resulted in less powder being present in the compaction zone at the edges of the rollers, which resulted in ribbons with a smaller overall width. The relative humidity for the storage of powders has shown to have minimal effect on the ribbon tensile strength at low RH conditions (10-20%). The lowest tensile strength of ribbons produced from lactose 200M and SD was for powders conditioned at 80% RH, whereas, ribbons produced from lactose 21AN at the same condition of 80% RH showed the highest tensile strength. The storage RH range 20-40% was found to be an optimum condition for roll compacting three lactose powders, as it resulted in a minimum amount of fines in the

  4. Roller compaction: Effect of relative humidity of lactose powder.

    PubMed

    Omar, Chalak S; Dhenge, Ranjit M; Palzer, Stefan; Hounslow, Michael J; Salman, Agba D

    2016-09-01

    The effect of storage at different relative humidity conditions, for various types of lactose, on roller compaction behaviour was investigated. Three types of lactose were used in this study: anhydrous lactose (SuperTab21AN), spray dried lactose (SuperTab11SD) and α-lactose monohydrate 200M. These powders differ in their amorphous contents, due to different manufacturing processes. The powders were stored in a climatic chamber at different relative humidity values ranging from 10% to 80% RH. It was found that the roller compaction behaviour and ribbon properties were different for powders conditioned to different relative humidities. The amount of fines produced, which is undesirable in roller compaction, was found to be different at different relative humidity. The minimum amount of fines produced was found to be for powders conditioned at 20-40% RH. The maximum amount of fines was produced for powders conditioned at 80% RH. This was attributed to the decrease in powder flowability, as indicated by the flow function coefficient ffc and the angle of repose. Particle Image Velocimetry (PIV) was also applied to determine the velocity of primary particles during ribbon production, and it was found that the velocity of the powder during the roller compaction decreased with powders stored at high RH. This resulted in less powder being present in the compaction zone at the edges of the rollers, which resulted in ribbons with a smaller overall width. The relative humidity for the storage of powders has shown to have minimal effect on the ribbon tensile strength at low RH conditions (10-20%). The lowest tensile strength of ribbons produced from lactose 200M and SD was for powders conditioned at 80% RH, whereas, ribbons produced from lactose 21AN at the same condition of 80% RH showed the highest tensile strength. The storage RH range 20-40% was found to be an optimum condition for roll compacting three lactose powders, as it resulted in a minimum amount of fines in the

  5. 4. DETAIL VIEW (SIDE A) OF HANDMADE STEEL BOX ASSOCIATED ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. DETAIL VIEW (SIDE A) OF HANDMADE STEEL BOX ASSOCIATED WITH THE DEPLETED URANIUM ALLOY DEVELOPMENT AND COMPONENT FABRICATION PROCESS. THE BOX WAS USED TO TRANSFER HEATED BLOCKS OF METAL (SHOWN IN THE OPENED DOOR) FROM THE MOLTEN SALT BATH TO THE ROLLER LINES. (4/28/62) - Rocky Flats Plant, Uranium Rolling & Forming Operations, Southeast section of plant, southeast quadrant of intersection of Central Avenue & Eighth Street, Golden, Jefferson County, CO

  6. Aspects of geometric calculation of the planetary gear train with intermediate rollers. Part 1

    NASA Astrophysics Data System (ADS)

    I-Kan, An; Il'In, A. S.; Lazurkevich, A. V.

    2016-04-01

    The paper presents the geometric calculation of the planetary gear train with intermediate rollers, where the number of intermediate rollers is greater or less than that of the teeth in the annular gear by one, the profile surface of the annular gear teeth being the same. The gear ratio is changed by both a value and a sign.

  7. Textile processing improvements due to high speed roller ginning of upland cotton

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Selective breeding has improved upland cotton fiber properties. Processing capacities of new high-speed roller ginning technology approach that of saw ginning. Spinning mills are interested in mill performance data comparing new upland cultivars processed by both saw and roller ginning. Four dive...

  8. Comparison of high-speed roller and saw ginning on Texas high plains cotton

    Technology Transfer Automated Retrieval System (TEKTRAN)

    New high-quality cotton cultivars have been adopted in the Southern High Plains recently and, as a result, interest has grown in finding harvest and ginning practices that better preserve fiber quality. Advancements in roller ginning technology have increased the ginning rate of some roller gins to ...

  9. Fatigue performance and equations of roller compacted concrete with fly ash

    SciTech Connect

    Sun, W.; Liu, J.; Qin, H.; Zhang, Y.; Jin, Z.; Qian, M.

    1998-02-01

    In this paper, the influence of fly ash on the fatigue performance of roller compacted concrete was studied. The fatigue equations of roller compacted concrete without and with fly ash, which can be used for designing pavement, are proposed through the method of the regressive analysis, and compared with that of the same grade common concrete pavement.

  10. Instantaneous fault frequencies estimation in roller bearings via wavelet structures

    NASA Astrophysics Data System (ADS)

    Rodopoulos, Konstantinos I.; Antoniadis, Ioannis A.

    2016-11-01

    The main target of the current paper is the effective application of the method proposed in "Antoniadis et al. (2014) [17], in roller bearings under variable speed. For this reason, roller bearing model with slip and real data coming from a test rig has been used. The method extracts useful information from a complicated signal where the overlap among the harmonics can raise up to 30%. According to the proposed method, a set of wavelet transforms of the signal is first obtained, using a structure of Complex Shifted Morlet Wavelets. The center frequencies and the bandwidths of the individual wavelets, as well as the number of wavelets used, are associated with the characteristic fault frequency and its harmonic components. In this way, a set of complex signals result in the time domain, equal to the number of the wavelets used. Then, the instantaneous frequencies of the signals are estimated by applying an appropriate subspace algorithm (as for e.g. ESPRIT), to the entire set of the resulting complex wavelet transforms, exploiting the corresponding subspace rotational invariance property of this set of complex signals. The iterative procedure brings up accurate results from complicated signals, separating the fault associated signal components. Also, the spectrograms of the processed signals confirm the ability to match excited areas with specific faults.

  11. Transient dynamic analysis of high-speed lightly loaded cylindrical roller bearings. 2: Computer program and results

    NASA Technical Reports Server (NTRS)

    Conry, T. F.; Goglia, P. R.

    1981-01-01

    The governing differential equations of motion for a high speed cylindrical roller bearing are programmed for numerical solution and plotted output. This computer program has the capability of performing a two dimensional or three dimensional simulation. Two numerical solutions of the governing differential equations were obtained to simulate the motion of a roller bearing, one for the two dimensional equations of motion and one for the three dimensional equations of motion. Computer generated plots were obtained and present such data as roller/cage interaction forces, roller/race traction forces, roller/race relative slip velocities and cage angular speed over a nondimensional time equivalent to 1.2 revolutions of the inner race. Roller axial displacement, roller skew angle, and skew moment are also plotted for the three dimensional solution. The trajectory of the cage center is plotted for both the two dimensional and three dimensional solutions.

  12. Space Shuttle Orbiter Atlantis Liquid Oxygen Prevalve Detent Roller Cracking Investigation

    NASA Technical Reports Server (NTRS)

    Holleman, Elizabeth; Eddleman, David; Richard, James; Jacobs, Rebecca

    2008-01-01

    During routine inspections of the Space Shuttle's Main Propulsion System (MPS) Liquid Oxygen (LO2) pre-valve, the mechanism provided to maintain the valve in the open position was found cracked. The mechanism is a Vespel roller held against the valve visor by a stack of Belleville springs. The roller has been found cracked 3 times. All three instances were in the same valve in the same location. There are 6 pre-valves on each orbiter, and only one has exhibited this problem. Every-flight inspections were instituted and the rollers were found to be cracked after only one flight. Engineers at Marshall Space Flight Center, Johnson Space Center and Kennedy Space Center worked together to determine a solution. There were several possible contributors to the failure: a mis-aligned visor, an out of specification edge with a sharp radius, an out of specification tolerance stack up of a Belleville spring stack that caused un-predicted loads on the Vespel SP-21 roller, and a dimple machined into the side of the roller to indicate LO2 compatibility that created a stress riser. The detent assembly was removed and replaced with parts that were on the low-side of the tolerance stack up to eliminate the potential for high loads on the detent roller. After one flight, the roller was inspected and showed fewer signs of wear and no cracks.

  13. Space Shuttle Orbiter Atlantis Liquid Oxygen Pre-Valve Detent Roller Cracking Investigation

    NASA Technical Reports Server (NTRS)

    Holleman, Elizabeth; Eddleman, David; Jacobs, Rebecca; Richard, James

    2008-01-01

    During routine inspections of the Space Shuttle s Main Propulsion System Liquid Oxygen (LO2) pre-valve, the mechanism provided to maintain the valve in the open position was found cracked. The mechanism is a Vespel roller held against the valve visor by a stack of Belleville springs. The roller has been found cracked 3 times. All three instances were in the same valve in the same location. There are 6 pre-valves on each orbiter, and only one has exhibited this problem. Every-flight inspections were instituted and the rollers were found to be cracked after only one flight. Engineers at Marshall Space Flight Center, Johnson Space Center, and Kennedy Space Center worked together to determine a solution. There were several possible contributors to the failure: a misaligned visor, an out-of-specification edge with a sharp radius, an out-of-specification tolerance stack up of a Belleville spring stack that caused un-predicted loads on the Vespel SP-21 roller, and a dimple machined into the side of the roller to indicate LO2 compatibility that created a stress riser. The detent assembly was removed and replaced with parts that were on the low side of the tolerance stack up to eliminate the potential for high loads on the detent roller. After one flight, the roller was inspected and showed fewer signs of wear and no cracks.

  14. Elevated Temperature Fracture Toughness and Fatigue Testing of Steels for Geothermal Applications

    SciTech Connect

    Cutler, R.A.; Goodman, E.C.; Hendrickson, R.R.

    1981-10-01

    Conventional drill bit steels exhibit increased wear and decreased toughness when run at elevated temperatures in geothermal wells. Bits are therefore run at lower speeds and lighter loads, resulting in lower penetration rates for geothermal drilling than for conventional rock drilling. Carpenter EX-00053, Timken CBS 600, Timken CBS 1000M and Vasco X-2M steels with improved hot hardness (improved wear resistance), were tested in conjunction with the steels used for cones (AISI 4829, 3915 and EX55) in conventional roller cones and lugs (AISI 8620, 9315 and EX55) in conventional roller cone rock bits. Short-rod fracture toughness measurements were made on each of these steels between room temperature and 400{degree}C. Fatigue crack resistance was determined at 300{degree}C for high-temperature steels and at room temperature for conventional steels. Scanning electron microscopy analyses of the fractured short-rod specimens were correlated with observed crack behavior from the test records. Materials testing results are discussed and steel selections made for improved geothermal bits. Carpenter EX-00053 and Timken CBS 1000M steels meet all design requirements for use in stabilizers, lugs and cones at temperatures to 400{degree}C. It is recommended that EX-00053 and CBS 1000M be manufactured for geothermal drilling at the Geysers site. [DJE 2005

  15. Softening Behavior of Hardness and Surface Fatigue of Rolling-Sliding Contact in the Case of Developed Alloy Steels

    NASA Astrophysics Data System (ADS)

    Redda, Daniel Tilahun; Nakanishi, Tsutomu; Deng, Gang

    To get high performance, downsizing and weight saving of the power transmission systems, the improvement of machine elements has been required. In this study, case-carburized gear materials for a high load-carrying capacity were developed. Low-alloyed steels with 1%Cr-0.2%Mo, 1%Cr-0.2%Mo-1%Si and 1%Cr-0.2%Mo-2%Ni (Cr-Mo steel, Cr-Mo-Si steel and Cr-Mo-Ni steel) were melted in a hypoxia vacuum. Test rollers were made of the developed steels, and they were carburized (Type A and Type B), hardened and tempered. Heating retention tests were carried out to investigate the softening behavior of hardness at high heating temperatures in the case of the developed steels. Roller tests were conducted under the rolling-sliding contact and high-load conditions to study the surface fatigue of the developed steels. From the obtained test results, it was found that the softening behavior of surface hardness at high temperatures in the cases of Cr-Mo-Si steel (Type A) and Cr-Mo-Ni steel (Type B) is lower than that in the cases of Cr-Mo steel (Type A) and Cr-Mo steel (Type B). In the cases of Cr-Mo-Si steel (A) and Cr-Mo-Ni steel (B), micro- and small-pitting area ratios are smaller and large-pitting life is longer than those in the cases of Cr-Mo steel(A) and Cr-Mo steel(B) under the same carburizing treatment method and high-load conditions. Furthermore, the relationship between the softening behavior of surface hardness on the heating pattern and the surface fatigue on the rolling-sliding contact of the developed alloy steels was clarified.

  16. Roller Bearing Health Monitoring Using CPLE Frequency Analysis Method

    NASA Technical Reports Server (NTRS)

    Jong, Jen-Yi; Jones, Jess H.

    2007-01-01

    This paper describes a unique vibration signature analysis technique Coherence Phase Line Enhancer (CPLE) Frequency Analysis - for roller bearing health monitoring. Defects of roller bearing (e.g. wear, foreign debris, crack in bearing supporting structure, etc.) can cause small bearing characteristic frequency shifts due to minor changes in bearing geometry. Such frequency shifts are often too small to detect by the conventional Power Spectral Density (PSD) due to its frequency bandwidth limitation. This Coherent Phase Line Enhancer technology has been evolving over the last few years and has culminated in the introduction of a new and novel frequency spectrum which is fully described in this paper. This CPLE technology uses a "key phasor" or speed probe as a preprocessor for this analysis. With the aid of this key phasor, this CPLE technology can develop a two dimensional frequency spectrum that preserves both amplitude and phase that is not normally obtained using conventional frequency analysis. This two-dimensional frequency transformation results in several newly defined spectral functions; i. e. CPLE-PSD, CPLE-Coherence and the CPLE-Frequency. This paper uses this CPLE frequency analysis to detect subtle, low level bearing related signals in the High Pressure Fuel Pump (HPFP) of the Space Shuttle Main Engine (SSME). For many rotating machinery applications, a key phasor is an essential measurement that is used in the detection of bearing related signatures. There are times however, when a key phasor is not available; i. e. during flight of any of the SSME turbopumps or on the SSME High Pressure Oxygen Turbopump (HPOTP) where no speed probe is present. In this case, the CPLE analysis approach can still be achieved using a novel Pseudo Key Phasor (PKP) technique to reconstruct a 1/Rev PKP signal directly from external vibration measurements. This paper develops this Pseudo Key Phasor technique and applies it to the SSME vibration data.

  17. The effect of primary loading on fatigue life of cylindrical roller bearings

    NASA Astrophysics Data System (ADS)

    Crețu, S. S.

    2016-08-01

    Experimental and theoretical works shown that if a roller-raceway rolling contact is loaded in the elastic-plastic domain then, after the first rolling cycles, the material elastically shakedowns to a slightly modified axial profile and stable compressive residual stresses. Fatigue life tests carried out on four groups of NJ206 cylindrical roller bearings pointed out the superiority of the bearings groups that primary supported a few cycles of rolling loading in the elastic-plastic domain. An elastic-perfect plastic analysis was performed to reveal the role played by the roller's crowning geometry, operating clearance, misalignment angle and operating loads on contact pressures distributions achieved between each roller and the corresponding inner and outer raceways. The modified reference rating lives, evaluated using the lamina technique, exposed a good agreement with the values provided by fatigue life tests.

  18. Strategies to simulate wheel-rail adhesion in degraded conditions using a roller-rig

    NASA Astrophysics Data System (ADS)

    Bosso, N.; Gugliotta, A.; Zampieri, N.

    2015-05-01

    Railway vehicles adopt mechatronic devices to maximize the traction/braking effort. These systems often use complex algorithms that require long experimental validation tests on track. The possibility to perform the same tests on a roller-rig gives the opportunity to simplify the validation activity, under safe conditions, and to reduce the costs. The main challenge is to be able to reproduce the same adhesion conditions on a roller-rig with respect to the track, especially in degraded conditions. First, the paper shows experiments performed to reproduce degraded adhesion on a conventional roller-rig for a single wheelset. Then, an innovative roller-rig is proposed in order to reproduce the effect of the passage of several wheelsets on the track.

  19. Acute effects of self-myofascial release using a foam roller on arterial function.

    PubMed

    Okamoto, Takanobu; Masuhara, Mitsuhiko; Ikuta, Komei

    2014-01-01

    Flexibility is associated with arterial distensibility. Many individuals involved in sport, exercise, and/or fitness perform self-myofascial release (SMR) using a foam roller, which restores muscles, tendons, ligaments, fascia, and/or soft-tissue extensibility. However, the effect of SMR on arterial stiffness and vascular endothelial function using a foam roller is unknown. This study investigates the acute effect of SMR using a foam roller on arterial stiffness and vascular endothelial function. Ten healthy young adults performed SMR and control (CON) trials on separate days in a randomized controlled crossover fashion. Brachial-ankle pulse wave velocity (baPWV), blood pressure, heart rate, and plasma nitric oxide (NO) concentration were measured before and 30 minutes after both SMR and CON trials. The participants performed SMR of the adductor, hamstrings, quadriceps, iliotibial band, and trapezius. Pressure was self-adjusted during myofascial release by applying body weight to the roller and using the hands and feet to offset weight as required. The roller was placed under the target tissue area, and the body was moved back and forth across the roller. In the CON trial, SMR was not performed. The baPWV significantly decreased (from 1,202 ± 105 to 1,074 ± 110 cm·s-1) and the plasma NO concentration significantly increased (from 20.4 ± 6.9 to 34.4 ± 17.2 μmol·L-1) after SMR using a foam roller (both p < 0.05), but neither significantly differed after CON trials. These results indicate that SMR using a foam roller reduces arterial stiffness and improves vascular endothelial function.

  20. Acute effects of self-myofascial release using a foam roller on arterial function.

    PubMed

    Okamoto, Takanobu; Masuhara, Mitsuhiko; Ikuta, Komei

    2014-01-01

    Flexibility is associated with arterial distensibility. Many individuals involved in sport, exercise, and/or fitness perform self-myofascial release (SMR) using a foam roller, which restores muscles, tendons, ligaments, fascia, and/or soft-tissue extensibility. However, the effect of SMR on arterial stiffness and vascular endothelial function using a foam roller is unknown. This study investigates the acute effect of SMR using a foam roller on arterial stiffness and vascular endothelial function. Ten healthy young adults performed SMR and control (CON) trials on separate days in a randomized controlled crossover fashion. Brachial-ankle pulse wave velocity (baPWV), blood pressure, heart rate, and plasma nitric oxide (NO) concentration were measured before and 30 minutes after both SMR and CON trials. The participants performed SMR of the adductor, hamstrings, quadriceps, iliotibial band, and trapezius. Pressure was self-adjusted during myofascial release by applying body weight to the roller and using the hands and feet to offset weight as required. The roller was placed under the target tissue area, and the body was moved back and forth across the roller. In the CON trial, SMR was not performed. The baPWV significantly decreased (from 1,202 ± 105 to 1,074 ± 110 cm·s-1) and the plasma NO concentration significantly increased (from 20.4 ± 6.9 to 34.4 ± 17.2 μmol·L-1) after SMR using a foam roller (both p < 0.05), but neither significantly differed after CON trials. These results indicate that SMR using a foam roller reduces arterial stiffness and improves vascular endothelial function. PMID:23575360

  1. Bilateral vertebral artery dissection possibly precipitated in delayed fashion as a result of roller coaster rides.

    PubMed

    Schneck, Michael; Simionescu, Monica; Bijari, Armita

    2008-01-01

    A 34-year-old woman presented with a 5-month history of persistent vertigo after multiple roller coaster rides, followed by neck pain for 1 month and then 2 weeks of blurred vision related to diplopia. She was ultimately found to have bilateral cervical vertebral artery dissection. The images are described and the literature is reviewed regarding late diagnosis of vertebral dissection and prior cases of roller coaster-associated dissection. PMID:18190821

  2. Stress Analysis of a New Disk-Type Variable Torque Slipping Clutch with Skewed Rollers

    NASA Astrophysics Data System (ADS)

    Feng, Ming; Ono, Kyosuke; Mimura, Kenji

    In this paper a new disk type of the variable torque slipping clutch with skewed rollers (VTSCSR) is presented and investigated both theoretically and experimentally. It is comprised of two flat disks, a number of skewed cylindrical rollers, and a cage. The slipping torque is produced by the skewed rollers rolling and slipping between the two disks. Based on the integral equation of the Boussinesq solution, the contact pressures are numerically calculated under the condition that the nonlinear equilibrium equations of the clutch elements are satisfied. By considering both pressure and friction, the components of subsurface stress are calculated from the integration of the Mindlin's subsurface stress equations of concentrated force. A numerical solver is then successfully developed by which the characteristics of the disk-type VTSCSR, including the torque capacity, angular velocities of the roller and cage, contact pressure and von Mises stress, etc, are calculated and illustrated for the typical designs. The influences on the distribution of the von Mises stress by applying various types of profiled rollers to the disk-type VTSCSR are also discussed. It has been found that the full crown with two arcs profiled roller can approximately give rise to the axially uniform distribution of the von Mises stress and therefore satisfies the design principle of the average damage of materials. In addition, the preliminary experiment was done in order to show the feasibility of this design idea and to verify the theoretical torque capacity.

  3. Armed Rollers: Does Nestling’s Vomit Function as a Defence against Predators?

    PubMed Central

    Parejo, Deseada; Avilés, Jesús M.; Peña, Aránzazu; Sánchez, Lourdes; Ruano, Francisca; Zamora-Muñoz, Carmen; Martín-Vivaldi, Manuel

    2013-01-01

    Chemical defences against predators are widespread in the animal kingdom although have been seldom reported in birds. Here, we investigate the possibility that the orange liquid that nestlings of an insectivorous bird, the Eurasian roller (Coracias garrulus), expel when scared at their nests acts as a chemical defence against predators. We studied the diet of nestling rollers and vomit origin, its chemical composition and deterrent effect on a mammal generalist predator. We also hypothesized that nestling rollers, as their main prey (i.e. grasshoppers) do from plants, could sequester chemicals from their prey for their use. Grasshoppers, that also regurgitate when facing to a threat, store the harmful substances used by plants to defend themselves against herbivores. We found that nestling rollers only vomit after being grasped and moved. The production of vomit depended on food consumption and the vomit contained two deterrent chemicals (hydroxycinnamic and hydroxybenzoic acids) stored by grasshoppers and used by plants to diminish herbivory, suggesting that they originate from the rollers’ prey. Finally, we showed for the first time that the oral secretion of a vertebrate had a deterrent effect on a model predator because vomit of nestling rollers made meat distasteful to dogs. These results support the idea that the vomit of nestling rollers is a chemical defence against predators. PMID:23874791

  4. Measurement and characterization of three-dimensional microstructures on precision roller surfaces

    NASA Astrophysics Data System (ADS)

    Kong, L. B.; Cheung, C. F.; Lee, W. B.; To, S.; Ren, M. J.

    2016-01-01

    Precision roller with microstructures is the key tooling component in the precision embossing by roller process such as Roll-to-Roll to manufacture optical plastic plates or films with three dimensional (3D)-microstructures. Measurement and analysis of 3D-microstructures on a precision roller is essential before the embossing process is being undertaken to ensure the quality of the embossed surfaces. Different from 3D-microstructures on a planar surface, it is difficult to measure and characterize the 3D-microstructures on the cylindrical surface of a precision roller due to the geometrical complexity of such integrated surfaces such as V-groove microstructures on a cylindrical surface. This paper presents a study of method and algorithms for the measurement and characterization of 3D-microstructures on a precision roller surface. A feature-based characterization method (FBCM) is proposed to analyze the V-groove microstructures. In this method, a normal template is generated based on the design specifications, and the measured data is fitted with the feature points. Hence alignment and matching of the measured data to the normal template based on the derived feature points are undertaken. After that the V-groove is characterized by some feature parameters such as pitch, depth, angle of the V-grooves. The method also provides an approach for the analysis of burs generated during the machining of Vgroove microstructures. A precision roller with V-groove microstructures has been machined by a Four-axis ultraprecision machine and the machined surface is measured by a contact measuring instrument. The measured data are then characterized and analyzed by the proposed FBCM. The results are presented and discussed, and they indicate the dominant and regular machining errors that are involved in the machining of the V-groove microstructures on roller surfaces.

  5. New roller pump disposable provides safety and simplifies occlusion setting.

    PubMed

    Lee-Sensiba, K; Azzaretto, N; Carolina, C; DiCarmine, N; Hymowitz, D; Kay, S; Kooker, K; Salogub, M; Wong, E; Tamari, Y

    1997-03-01

    A new disposable insert for the arterial roller pump, the Better-Header, provides safety and functionality beyond what standard tubing provides. It automatically limits pump outlet pressure to a level determined by the user and provides a self-contained, simple means to set pump occlusion. The Better-Header consists of a Starling-like pressure relief valve connected across standard header tubing. As long as arterial line pressure at the pump outlet remains below a set limit, the valve is closed. If line pressure approaches the pressure limit, the valve opens, preventing overpressurization by shunting blood from pump outlet to inlet. The Better-Header can also be used to set occlusion by the "dynamic method" to obtain nonocclusive settings. The Better-Header was evaluated in the lab for its pressure-flow characteristics. Even when the arterial line was completely clamped at a pump flow of 7 L/min, line pressure was limited to a safe level and all circuit connections were preserved. The Better-Header has been used successfully at North Shore University Hospital in over 500 clinical cases covering a wide range of patients and procedures. In several instances, the user was alerted to high pressure situations by fluid flow through the valve and by an audible alarm, allowing rapid correction of the source of pressure. Compared to the standard setup, the Better-Header maintains outlet pressure within safe, user-settable limits, and permits consistent, nonocclusive settings with predictable retrograde flow.

  6. Modeling Oxygen Uptake during V1 Treadmill Roller Skiing

    PubMed Central

    BOWEN, ROBERT S.; JENSEN, RANDALL L.; RYAN, JENNIFER M.; WATTS, PHILLIP B.

    2009-01-01

    The use of regression equations to predict oxygen uptake in relation to speed, grade, power output, and anthropometric characteristics is common in cardiac rehabilitation and athlete fitness testing. Research has suggested that sport specific testing improves the reliability of the test methodology and is appropriate for the development of effective training programs. This study focused on the development of a cross-country skiing specific predictor of maximal oxygen uptake based on treadmill speed, treadmill grade, gender, and body mass. This project simulated snow skiing on a large research treadmill using roller skis. A small sample size (N = 34) warranted the use of bootstrapping techniques and multiple regression analysis to develop a cross-country skiing specific model of oxygen uptake. The stability of each bootstrapped sample was confirmed via a cross-validation procedure. The equation of best resolve was: VO2 = −4.534 + 0.223(G) + 0.061(BM) + 0.139(TG) + 0.016(TS) in which G = Gender, BM = Body Mass, TG = Treadmill Grade, TS = Treadmill Speed. The resultant model can be used to design training programs, develop athlete fitness testing or research protocols, and to predict maximal oxygen uptake when sophisticated metabolic measurement equipment is unavailable. PMID:27182311

  7. Roller coaster-associated subarachnoid hemorrhage--report of 2 cases.

    PubMed

    Rutsch, Sebastian; Niesen, Wolf-Dirk; Meckel, Stephan; Reinhard, Matthias

    2012-04-15

    The most common neurological injuries associated with roller coaster rides are subdural hematoma and cervical artery dissection. We report two cases of roller-coaster associated subarachnoid hemorrhage (SAH). A 40-year-old healthy man developed a strong, holocephalic headache during a roller coaster ride. SAH Hunt & Hess grade II and Fisher grade 3 was diagnosed. An underlying aneurysm of the anterior communicating artery was successfully treated with coil embolization. A 41-year-old female (smoker, otherwise healthy) experienced a sudden, strong headache and diplopia during a roller coaster ride. A perimesencephalic SAH (Hunt & Hess grade II, Fisher grade 3) was disclosed by a CT scan. No aneurysm was detected on angiography. Both patients were discharged without neurological disability. In conclusion, SAH is a rare but relevant differential diagnosis in cases of acute headache during roller coaster rides. Both aneurysmal and non-aneurysmal perimesencephalic SAH can occur. A combination of mechanical factors and excessive blood pressure rises in vulnerable persons is discussed. PMID:22177088

  8. Oxygen mass transfer and scale-up studies in baffled roller bioreactors.

    PubMed

    Nikakhtari, H; Song, W; Nemati, M; Hill, G A

    2014-02-01

    Oxygen mass transfer was studied in conventional, bead mill and baffled roller bioreactors. Using central composite rotational design, impacts of size, rotation speed and working volume on the oxygen mass transfer were evaluated. Baffled roller bioreactor outperformed its conventional and bead mill counterparts, with the highest k(L)a obtained in these configurations being 0.58, 0.19, 0.41 min(-1), respectively. Performances of the bead mill and baffled roller bioreactor were only comparable when a high bead loading (40%) was applied. Regardless of configuration increase in rotation speed and decrease in working volume improved the oxygen mass transfer rate. Increase in size led to enhanced mass transfer and higher k(L)a in baffled roller bioreactor (0.49 min(-1) for 2.2 L and 1.31 min(-1) for 55 L bioreactors). Finally, the experimentally determined k(L)a in the baffled roller bioreactors of different sizes fit reasonably well to an empirical correlation describing the k(L)a in terms of dimensionless numbers.

  9. Improving the granule strength of roller-compacted ibuprofen sodium for hot-melt coating processing.

    PubMed

    Lopes, Diogo Gomes; Garsuch, Verena; Becker, Karin; Paudel, Amrit; Stehr, Michael; Zimmer, Andreas; Salar-Behzadi, Sharareh

    2016-08-20

    Solvent-free hot-melt coating processing is a novel and cost-efficient approach to manufacturing taste-masked multiparticulate systems. However, most API powders are fine and cohesive and not processable by hot-melt coating. The aim of this study was to produce dense and abrasion-resistant granules with high drug content (>80%) via roller compaction for hot-melt coating process optimization. The selected API was ibuprofen sodium dihydrate, a salt of ibuprofen with improved bioavailability and poor intrinsic compactibility. The formulation and roller compaction process were developed for the production of granules with 94%w/w of API and low friability (∼30%), using sorbitol and isomalt as excipients. The strong bonding mechanism relied on powder jamming prior to the rollers and was investigated via scanning electron microscopy, differential scanning calorimetry and small and wide angle X-ray scattering. It was shown that sorbitol crystals are solubilized during roller compaction and recrystallize as sorbitol hydrate, acting as strong solid bridges. The robustness of the roller compaction process and the re-compaction of fines were investigated. A statistical design of experiments was conducted to evaluate the hot-melt coating process for taste masking of ibuprofen sodium granules. Taste masking required coating ratios higher than 40%w/w of granule batch, emphasizing the need for high-drug-content and abrasion-resistant granules.

  10. Unified compaction curve model for tensile strength of tablets made by roller compaction and direct compression.

    PubMed

    Farber, Leon; Hapgood, Karen P; Michaels, James N; Fu, Xi-Young; Meyer, Robert; Johnson, Mary-Ann; Li, Feng

    2008-01-01

    A model that describes the relationship between roller-compaction conditions and tablet strength is proposed. The model assumes that compaction is cumulative during roller compaction and subsequent granule compaction, and compact strength (ribbon and tablet) is generated irreversibly as if strength is controlled by plastic deformation of primary particles only. Roller-compaction is treated as a compaction step where the macroscopic ribbon strength is subsequently destroyed in milling. This loss in strength is irreversible and tablets compressed from the resulting granulation are weaker than those compressed by direct compression at the same compression force. Roller-compacted ribbons were produced at a range of roll forces for three formulations and subsequently milled and compacted into tablets. Once the total compaction history is taken in account, the compaction behavior of the uncompacted blends and the roller-compacted granules ultimately follow a single master compaction curve--a unified compaction curve (UCC). The model successfully described the compaction behavior of DC grade starch and formulations of lactose monohydrate with 50% or more microcrystalline cellulose, and may be more generally applicable to systems containing significant proportions of any plastically deforming material, including MCC and starch. PMID:17689211

  11. Towards the development of a work index for the Roller Press

    SciTech Connect

    Klymowsky, I.B.; Liu, J.

    1997-11-01

    This paper details the development of a functional work index that characterises the relationship between the energy that is imparted by a Roller Press into materials, against the resultant size reduction achieved. Such a Roller Press work index is necessary for this new grinding technology to differentiate it from Bond`s grinding work index, and to clear up confusion that arises with such comparison to Bond. The energy usage in a Roller Press does not follow Bond`s {open_quotes}Third Theory of Comminution{close_quotes} but rather Rittinger`s theory of new surface creation. The relationships for such a work index have been developed from the viewpoint of an equipment manufacturer with the hope that they will be of assistance to the minerals industry in the design of grinding circuits incorporating Roller Press comminution. The work index contains modification factors that reflects the effect of oversize, fines, moisture, closed-circuit operation and roll surface characteristics on the energy verses size reduction relationship. It has evolved from the results obtained from testing of a wide range of ore and mineral types that include bauxite, coal, kimberlite, limestone, iron and chrome ores, base metal and gold ores. The results show that even for such a diverse range of materials, they all demonstrate similarities of behaviour when comminuted in a Roller Press.

  12. Improving the granule strength of roller-compacted ibuprofen sodium for hot-melt coating processing.

    PubMed

    Lopes, Diogo Gomes; Garsuch, Verena; Becker, Karin; Paudel, Amrit; Stehr, Michael; Zimmer, Andreas; Salar-Behzadi, Sharareh

    2016-08-20

    Solvent-free hot-melt coating processing is a novel and cost-efficient approach to manufacturing taste-masked multiparticulate systems. However, most API powders are fine and cohesive and not processable by hot-melt coating. The aim of this study was to produce dense and abrasion-resistant granules with high drug content (>80%) via roller compaction for hot-melt coating process optimization. The selected API was ibuprofen sodium dihydrate, a salt of ibuprofen with improved bioavailability and poor intrinsic compactibility. The formulation and roller compaction process were developed for the production of granules with 94%w/w of API and low friability (∼30%), using sorbitol and isomalt as excipients. The strong bonding mechanism relied on powder jamming prior to the rollers and was investigated via scanning electron microscopy, differential scanning calorimetry and small and wide angle X-ray scattering. It was shown that sorbitol crystals are solubilized during roller compaction and recrystallize as sorbitol hydrate, acting as strong solid bridges. The robustness of the roller compaction process and the re-compaction of fines were investigated. A statistical design of experiments was conducted to evaluate the hot-melt coating process for taste masking of ibuprofen sodium granules. Taste masking required coating ratios higher than 40%w/w of granule batch, emphasizing the need for high-drug-content and abrasion-resistant granules. PMID:27346416

  13. Effect of Roller Profile on Cylindrical Roller Bearing Life Prediction. Part 1; Comparison of Bearing Life Theories

    NASA Technical Reports Server (NTRS)

    Poplawski, Joseph V.; Peters, Steven M.; Zaretsky, Erwin V.

    2001-01-01

    Four rolling-element bearing life theories were chosen for analysis and compared for a simple roller-race geometry model. The life theories were those of Weibull; Lundberg and Palmgren; Ioannides and Harris; and Zaretsky. The analysis without a fatigue limit of Ioannides and Harris is identical to the Lundberg and Palmgren analysis, and the Weibull analysis is similar to that of Zaretsky if the exponents are chosen to be identical. The resultant predicted life a each stress condition not only depends on the life equation used but also on the Weibull slope assumed. The least variation in predicted life with Weibull slope comes with the Zaretsky equation. Except for a Weibull slope of 1.11, at which the Weibull equation predicts the highest lives, the highest lives are predicted for the Zaretsky equation. For Weibull slopes of 1.5 and 2, both the Lundherg-Palmgren and Ioannides-Harris (where tau(sub u) = 0) equations predict lower lives than the ANSI/ABMA/ISO standard. Based upon the Hertz stresses for line contact, the accepted load-life exponent of 10/3 results in a maximum Hertz stress-life exponent equal to 6.6. This value is inconsistent with that experienced in the field. The assumption of as shear stress fatigue limit tau(sub u) results in Hertz stress-life exponents greater than are experimentally verifiable.

  14. The factors influencing urinary arsenic excretion and metabolism of workers in steel and iron smelting foundry.

    PubMed

    Shuhua, Xi; Qingshan, Sun; Fei, Wang; Shengnan, Liu; Ling, Yan; Lin, Zhang; Yingli, Song; Nan, Yan; Guifan, Sun

    2014-01-01

    In order to evaluate the degree of arsenic (As) exposure and the factors influencing urinary As excretion and metabolism, 192 workers from a steel and iron smelting plant, with different type of work in production such as roller, steel smelting, iron smelting and metallic charge preparation, were recruited. Information about characteristics of each subject was obtained by questionnaire and inorganic As (iAs), monomethylarsonic acid (MMA), dimethylarsinic acid (DMA) in urine were determined. The results showed that steel smelters had significantly higher concentrations of DMA and total As (TAs) than rollers and metallic charge preparation workers, and iron and steel smelters had a higher value of primary methylation index and lower proportion of the iAs (iAs%) than rollers and metallic charge preparation workers. In steel smelters, urinary As level exceeded the biological exposure index (BEI) limit for urinary As of 35 μg/l by 65.52%, and higher than metallic charge preparation workers (35.14%). The individuals consumed seafood in recent 3 days had a higher TAs than the individuals without seafood consumption. Multivariate logistic regression analysis showed that different jobs, taken Chinese medicine of bezoar and seafood consumption in recent 3 days were significantly associated with urinary TAs exceeded BEI limit value 35 μg/l. Our results suggest that workers in steel and iron smelting plant had a lower level of As exposure, and seafood consumption and taking Chinese medicine of bezoar also could increase the risk of urinary TAs exceeded BEI limit value.

  15. 76 FR 6397 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-02-04

    ... China, 52 FR 22667 (June 15, 1987) (``Order''). On December 23, 2010, pursuant to section 751(a)(2)(B)(i... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the... shipper review (``NSR'') of the antidumping duty order on tapered roller bearings (``TRBs'') from...

  16. 76 FR 45777 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-01

    ... China, 52 FR 22667 (June 15, 1987) (``Order''). On June 30, 2011, pursuant to section 751(a)(2)(B)(i) of... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the... review (``NSR'') of the antidumping duty order on tapered roller bearings (``TRBs'') from the...

  17. 77 FR 45588 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-01

    ... Republic of China, 52 FR 22667 (June 15, 1987) (``Order''). \\2\\ See 19 CFR 351.214(d). In its submission... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the... on tapered roller bearings from the People's Republic of China (``PRC'') meets the statutory...

  18. 77 FR 45587 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, from the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-01

    ... Republic of China, 52 FR 22667 (June 15, 1987) (``Order''). \\2\\ See 19 CFR 351.214(d). In its submission... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, from the... on tapered roller bearings (``TRBs'') from the People's Republic of China (``PRC'') meets...

  19. [Improvement of dissolution test using micro-controlled roller pump].

    PubMed

    Nagai, Noriaki; Konishi, Nahoko; Nitta, Tadahisa; Taga, Atsushi; Ito, Yoshimasa

    2012-01-01

    The dissolution test is a core performance test in pharmaceutical development and quality control of solid drug products. The conventional HPLC dissolution method (batch-sampling method) involves many steps including the filtration, collection and replenishment of sample solutions. We previously reported a dissolution test that involved microdialysis methods (microdialysis-HPLC method) and allowed many steps to be omitted. However, the recovery rate of theophylline by the microdialysis-HPLC method was lower, and the decrease in the flow rate through the dialysis probe caused variation between each tablet. In this study, we have attempted to improve the dissolution test by using a precise micro-controlled roller pump and microfiltering probe (microfiltering-HPLC method). Sustained release preparations of Theodur (100 mg) were used, and the test solutions used were water, buffer at pH 1.2 and pH 6.8, and pH 6.8-buffer containing 0.1-1% polysorbate 80 or sodium lauryl sulfate. In all test solutions, the microfiltering-HPLC method was able to accomplish continuous sampling of sample solutions, and the recovery rate of theophylline was over 90%. The dissolution behavior by the microfiltering-HPLC method tends to reflect the pharmaceutical design in comparison with the batch-sampling method, and the standard deviations by the microfiltering-HPLC are lower than with the batch-sampling method. In addition, the microfiltering-HPLC method allows many steps to be omitted, such as the filtration, collection and replenishment of sample solutions. These findings provide significant information that can be used in the pharmaceutical development and quality assessment of solid drug products.

  20. Lubrication of high-speed, large bore tapered-roller bearings

    NASA Technical Reports Server (NTRS)

    Parker, R. J.; Signer, H. R.

    1977-01-01

    The performance of 120.65-mm- (4.75-in.-) bore tapered-roller bearings was investigated at shaft speeds up to 15,000 rpm (18,000 DN). Temperature distribution and bearing heat generation were determined as a function of shaft speed, radial and thrust loads, lubricant flow rate, and lubricant inlet temperature. Lubricant was supplied either by jets or by a combination of holes through the cone directly to the cone-rib contact and jets at the roller small-end side. Cone-rib lubrication significantly improved high-speed tapered-roller bearing performance, yielding lower cone-face temperatures and lower power loss and allowing lower lubricant flow rates for a given speed condition. Bearing temperatures increased with increased shaft speed and decreased with increased lubricant flow rate. Bearing power loss increased with increased shaft speed and increased lubricant flow rate.

  1. Fully-automated roller bottle handling system for large scale culture of mammalian cells.

    PubMed

    Kunitake, R; Suzuki, A; Ichihashi, H; Matsuda, S; Hirai, O; Morimoto, K

    1997-01-20

    A fully automatic and continuous cell culture system based on roller bottles is described in this paper. The system includes a culture rack storage station for storing a large number of roller bottles filled with culture medium and inoculated with mammalian cells, mass-handling facility for extracting completed cultures from the roller bottles, and replacing the culture medium. The various component units of the system were controlled either by a general-purpose programmable logic controller or a dedicated controller. The system provided four subsequent operation modes: cell inoculation, medium change, harvesting, and medium change. The operator could easily select and change the appropriate mode from outside of the aseptic area. The development of the system made large-scale production of mammalian cells, and manufacturing and stabilization of high quality products such as erythropoietin possible under total aseptic control, and opened up the door for industrial production of physiologically active substances as pharmaceutical drugs by mammalian cell culture.

  2. Computational and experimental investigation of flow and particle settling in a roller bottle bioreactor.

    PubMed

    Muzzio, F J; Unger, D R; Liu, M; Bramble, J; Searles, J; Fahnestock, P

    1999-04-20

    It is shown that cell settling is a key factor affecting the performance of roller bottle bioreactors. The two-dimensional cross-sectional flow at the center of a roller bottle is simulated using a finite difference method, and the settling behavior of cells is simulated using particle dynamics algorithms and validated experimentally using fluorescent particles. The settling behavior of particles in the roller bottle flow is studied using both steady and time dependent rotation rates. Under steady flow conditions the flow is divided into two regions: one where the particles settle to the wall and one where the particles remain suspended indefinitely. The relative size of these two regions depends on the ratio of the settling velocity to the rotation rate of the bottle. For unsteady flows generated by periodic changes of the bottle rotation direction, the settling of cells is accelerated significantly, leading to complete deposition in just a few turns of the bottle. PMID:10099595

  3. Roller-style electrostatic printing of prepatterned few-layer-graphenes

    NASA Astrophysics Data System (ADS)

    Liang, Xiaogan; Giacometti, Valentina; Ismach, Ariel; Harteneck, Bruce D.; Olynick, Deirdre L.; Cabrini, Stefano

    2010-01-01

    Electrostatic exfoliation of patterned few-layer-graphenes was demonstrated using a method compatible with high throughput roll-to-roll manufacturing. A patterned graphite template was placed on a roller and used to exfoliate patterned graphene on a planar substrate. The exfoliated graphene features were subsequently characterized by Raman spectroscopy. In comparison with previously demonstrated planar electrostatic exfoliation approach, the roller-style method can create a narrower distribution of thickness of few-layer-graphenes, which is attributed to the combinational action of tangential rolling friction and electrostatic forces. This roller-style electrostatic printing technique could be applied for roll-to-roll manufacturing of graphene-based devices in the future.

  4. A method for testing railway wheel sets on a full-scale roller rig

    NASA Astrophysics Data System (ADS)

    Liu, Binbin; Bruni, Stefano

    2015-09-01

    Full-scale roller rigs for tests on a single axle enable the investigation of several dynamics and durability problems related with the design and operation of the railway rolling stock. In order to exploit the best potential of this test equipment, appropriate test procedures need to be defined, particularly in terms of actuators' references, to make sure that meaningful wheel -rail contact conditions can be reproduced. The aim of this paper is to propose a new methodology to define the forces to be generated by the actuators in the rig in order to best reproduce the behaviour of a wheel set and especially the wheel -rail contact forces in a running condition of interest as obtained either from multi-body system (MBS) simulation or from on-track measurements. The method is supported by the use of a mathematical model of the roller rig and uses an iterative correction scheme, comparing the time histories of the contact force components from the roller rig test as predicted by the mathematical model to a set of target contact force time histories. Two methods are introduced, the first one considering a standard arrangement of the roller rig, the second one assuming that a differential gear is introduced in the rig, allowing different rolling speeds of the two rollers. Results are presented showing that the deviation of the roller rig test results from the considered targets can be kept within low tolerances (1% approximately) as far as the vertical and lateral contact forces on both wheels are concerned. For the longitudinal forces, larger deviations are obtained except in the case where a differential gear is introduced.

  5. An investigation into the impact of magnesium stearate on powder feeding during roller compaction.

    PubMed

    Dawes, Jason; Gamble, John F; Greenwood, Richard; Robbins, Phil; Tobyn, Mike

    2012-01-01

    A systematic evaluation on the effect of magnesium stearate on the transmission of a placebo formulation from the hopper to the rolls during screw fed roller compaction has been carried out. It is demonstrated that, for a system with two 'knurled' rollers, addition of 0.5% w/w magnesium stearate can lead to a significant increase in ribbon mass throughput, with a consequential increase in roll gap, compared to an unlubricated formulation (manufactured at equivalent process conditions). However, this effect is reduced if one of the rollers is smooth. Roller compaction of a lubricated formulation using two smooth rollers was found to be ineffective due to a reduction in friction at the powder/roll interface, i.e. powder was not drawn through the rollers leading to a blockage in the feeding system. An increase in ribbon mass throughput could also be achieved if the equipment surfaces were pre-lubricated. However this increase was found to be temporary suggesting that the residual magnesium stearate layer was removed from the equipment surfaces. Powder sticking to the equipment surfaces, which is common during pharmaceutical manufacturing, was prevented if magnesium stearate was present either in the blend, or at the roll surface. It is further demonstrated that the influence of the hopper stirrer, which is primarily used to prevent bridge formation in the hopper and help draw powder more evenly into the auger chamber, can lead to further mixing of the formulation, and could therefore affect a change in the lubricity of the carefully blended input material.

  6. Coal grinding by roller grinding mills for pulverized coal injection in blast furnaces

    SciTech Connect

    Kasseck, K.; Salewski, G.

    1995-10-01

    Roller grinding mills are increasingly being used for producing the pulverized coal required for injection into blast furnaces, an accepted technology worldwide for lowering coke consumption in blast furnaces. Coal is currently being injected into blast furnaces at the rate of 80 to 200 kg/tonne of hot metal which results in a coke savings of 72 to 180 kg/tonne of hot metal. The pulverized coal for coal injection is produced in coal grinding and drying plants currently having a capacity from 15 to 240 tonnes/hr. The grinding plant with Loesche roller grinding mills at the Ilva steelworks, Taranto, Italy, that is described, illustrates design concepts and operation.

  7. High speed cylindrical roller bearing analysis, SKF computer program CYBEAN. Volume 2: User's manual

    NASA Technical Reports Server (NTRS)

    Kleckner, R. J.; Pirvics, J.

    1978-01-01

    The CYBEAN (Cylindrical Bearing Analysis) was created to detail radially loaded, aligned and misaligned cylindrical roller bearing performance under a variety of operating conditions. Emphasis was placed on detailing the effects of high speed, preload and system thermal coupling. Roller tilt, skew, radial, circumferential and axial displacement as well as flange contact were considered. Variable housing and flexible out-of-round outer ring geometries, and both steady state and time transient temperature calculations were enabled. The complete range of elastohydrodynamic contact considerations, employing full and partial film conditions were treated in the computation of raceway and flange contacts. Input and output architectures containing guidelines for use and a sample execution are detailed.

  8. Roller-Massager Application to the Quadriceps and Knee-Joint Range of Motion and Neuromuscular Efficiency During a Lunge

    PubMed Central

    Bradbury-Squires, David J.; Noftall, Jennifer C.; Sullivan, Kathleen M.; Behm, David G.; Power, Kevin E.; Button, Duane C.

    2015-01-01

    Context: Roller massagers are used as a recovery and rehabilitative tool to initiate muscle relaxation and improve range of motion (ROM) and muscular performance. However, research demonstrating such effects is lacking. Objective: To determine the effects of applying a roller massager for 20 and 60 seconds on knee-joint ROM and dynamic muscular performance. Design: Randomized controlled clinical trial. Setting: University laboratory. Patients or Other Participants: Ten recreationally active men (age = 26.6 ± 5.2 years, height = 175.3 ± 4.3 cm, mass = 84.4 ± 8.8 kg). Intervention(s): Participants performed 3 randomized experimental conditions separated by 24 to 48 hours. In condition 1 (5 repetitions of 20 seconds) and condition 2 (5 repetitions of 60 seconds), they applied a roller massager to the quadriceps muscles. Condition 3 served as a control condition in which participants sat quietly. Main Outcome Measure(s): Visual analog pain scale, electromyography (EMG) of the vastus lateralis (VL) and biceps femoris during roller massage and lunge, and knee-joint ROM. Results: We found no differences in pain between the 20-second and 60-second roller-massager conditions. During 60 seconds of roller massage, pain was 13.5% (5.7 ± 0.70) and 20.6% (6.2 ± 0.70) greater at 40 seconds and 60 seconds, respectively, than at 20 seconds (P < .05). During roller massage, VL and biceps femoris root mean square (RMS) EMG was 8% and 7%, respectively, of RMS EMG recorded during maximal voluntary isometric contraction. Knee-joint ROM was 10% and 16% greater in the 20-second and 60-second roller-massager conditions, respectively, than the control condition (P < .05). Finally, average lunge VL RMS EMG decreased as roller-massage time increased (P < .05). Conclusions: Roller massage was painful and induced muscle activity, but it increased knee-joint ROM and neuromuscular efficiency during a lunge. PMID:25415414

  9. 77 FR 16859 - Tapered Roller Bearings From China; Scheduling of a Full Five-Year Review

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-22

    ... that a full review pursuant to section 751(c)(5) of the Act should proceed (76 FR 72213, November 22... amended. The amendments took effect on November 7, 2011. See 76 FR 61937 (Oct. 6, 2011) and the newly... COMMISSION Tapered Roller Bearings From China; Scheduling of a Full Five- Year Review AGENCY: United...

  10. 77 FR 12326 - Tapered Roller Bearings From China; Scheduling of a Full Five-Year Review

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-29

    ... to section 751(c)(5) of the Act should proceed (76 FR 72213, November 22, 2011). A record of the... amendments took effect on November 7, 2011. See 76 FR 61937 (Oct. 6, 2011) and the newly revised Commission's... COMMISSION Tapered Roller Bearings From China; Scheduling of a Full Five- Year Review AGENCY: United...

  11. A study on the fabrication of main scale of linear encoder using continuous roller imprint method

    NASA Astrophysics Data System (ADS)

    Fan, Shanjin; Shi, Yongsheng; Yin, Lei; Feng, Long; Liu, Hongzhong

    2013-10-01

    Linear encoder composed of main and index scales has an extensive application in the field of modern precision measurement. The main scale is the key component of linear encoder as measuring basis. In this article, the continuous roller imprint technology is applied to the manufacturing of the main scale, this method can realize the high efficiency and low cost manufacturing of the ultra-long main scale. By means of the plastic deformation of the soft metal film substrate, the grating microstructure on the surface of the cylinder mold is replicated to the soft metal film substrate directly. Through the high precision control of continuous rotational motion of the mold, ultra-long high precision grating microstructure is obtained. This paper mainly discusses the manufacturing process of the high precision cylinder mold and the effects of the roller imprint pressure and roller rotation speed on the imprint replication quality. The above process parameters were optimized to manufacture the high quality main scale. At last, the reading test of a linear encoder contains the main scale made by the above method was conducted to evaluate its measurement accuracy, the result demonstrated the feasibility of the continuous roller imprint method.

  12. Investigation of Tapered Roller Bearing Damage Detection Using Oil Debris Analysis

    NASA Technical Reports Server (NTRS)

    Dempsey, Paula J.; Krieder, Gary; Fichter, Thomas

    2006-01-01

    A diagnostic tool was developed for detecting fatigue damage to tapered roller bearings. Tapered roller bearings are used in helicopter transmissions and have potential for use in high bypass advanced gas turbine aircraft engines. This diagnostic tool was developed and evaluated experimentally by collecting oil debris data from failure progression tests performed by The Timken Company in their Tapered Roller Bearing Health Monitoring Test Rig. Failure progression tests were performed under simulated engine load conditions. Tests were performed on one healthy bearing and three predamaged bearings. During each test, data from an on-line, in-line, inductance type oil debris sensor was monitored and recorded for the occurrence of debris generated during failure of the bearing. The bearing was removed periodically for inspection throughout the failure progression tests. Results indicate the accumulated oil debris mass is a good predictor of damage on tapered roller bearings. The use of a fuzzy logic model to enable an easily interpreted diagnostic metric was proposed and demonstrated.

  13. Design study of a continuously variable roller cone traction CVT for electric vehicles

    NASA Technical Reports Server (NTRS)

    Mccoin, D. K.; Walker, R. D.

    1980-01-01

    Continuously variable ratio transmissions (CVT) featuring cone and roller traction elements and computerized controls are studied. The CVT meets or exceeds all requirements set forth in the design criteria. Further, a scalability analysis indicates the basic concept is applicable to lower and higher power units, with upward scaling for increased power being more readily accomplished.

  14. The Dynamics of Plant Closings: An Extended Emotional Roller Coaster Ride.

    ERIC Educational Resources Information Center

    Hurst, Joe B.; Shepard, John W.

    1986-01-01

    Millions of United States' workers are unemployed, many of them dislocated from their jobs and careers by extended layoffs, drastic manpower reductions, and plant closings. Describes a model of the emotional roller coaster ride taken by employees displaced by a plant closing and suggests approaches to helping them and their families. (Author/ABB)

  15. "Roller coaster maneuver via lateral orbital approach" for reduction of isolated zygomatic arch fractures.

    PubMed

    Pilanci, Ozgur; Basaran, Karaca; Datli, Asli; Kuvat, Samet Vasfi

    2013-11-01

    Numerous techniques have been reported for the reduction of zygomatic arch fractures. In this article, we aimed to describe a technique we named as "roller coaster maneuver via lateral orbital approach" to closed reduction of the isolated-type zygomatic arch fractures. Surgical outcomes of 14 patients treated with this method were outlined. PMID:24220411

  16. The Comfortable Roller Coaster--on the Shape of Tracks with a Constant Normal Force

    ERIC Educational Resources Information Center

    Nordmark, Arne B.; Essen, Hanno

    2010-01-01

    A particle that moves along a smooth track in a vertical plane is influenced by two forces: gravity and normal force. The force experienced by roller coaster riders is the normal force, so a natural question to ask is, what shape of the track gives a normal force of constant magnitude? Here we solve this problem. It turns out that the solution is…

  17. One City, Two Worlds, and Yet...: New York from "Roller Skates" to "Stevie."

    ERIC Educational Resources Information Center

    Hendrickson, Linnea

    1998-01-01

    Explores Ruth Sawyer's "Roller Skates" and John Steptoe's "Stevie"--two very different works linked by common themes and settings. Concludes that these works portray children exploring the variety and richness of life in New York City of the 1890s and of the 1960s, and that both emphasize the importance of love, family, and reaching out to others.…

  18. High speed cylindrical roller bearing analysis. SKF computer program CYBEAN. Volume 2: User's manual

    NASA Technical Reports Server (NTRS)

    Dyba, G. J.; Kleckner, R. J.

    1981-01-01

    CYBEAN (CYlindrical BEaring ANalysis) was created to detail radially loaded, aligned and misaligned cylindrical roller bearing performance under a variety of operating conditions. Emphasis was placed on detailing the effects of high speed, preload and system thermal coupling. Roller tilt, skew, radial, circumferential and axial displacement as well as flange contact were considered. Variable housing and flexible out-of-round outer ring geometries, and both steady state and time transient temperature calculations were enabled. The complete range of elastohydrodynamic contact considerations, employing full and partial film conditions were treated in the computation of raceway and flange contacts. The practical and correct implementation of CYBEAN is discussed. The capability to execute the program at four different levels of complexity was included. In addition, the program was updated to properly direct roller-to-raceway contact load vectors automatically in those cases where roller or ring profiles have small radii of curvature. Input and output architectures containing guidelines for use and two sample executions are detailed.

  19. Spherical roller bearing analysis. SKF computer program SPHERBEAN. Volume 2: User's manual

    NASA Technical Reports Server (NTRS)

    Kleckner, R. J.; Dyba, G. J.

    1980-01-01

    The user's guide for the SPHERBEAN computer program for prediction of the thermomechanical performance characteristics of high speed lubricated double row spherical roller bearings is presented. The material presented is structured to guide the user in the practical and correct implementation of SPHERBEAN. Input and output, guidelines for program use, and sample executions are detailed.

  20. Daylighting performance evaluation of a bottom-up motorized roller shade

    SciTech Connect

    Kapsis, K.; Athienitis, A.K.; Zmeureanu, R.G.; Tzempelikos, A.

    2010-12-15

    This paper presents an experimental and simulation study for quantifying the daylighting performance of bottom-up roller shades installed in office spaces. The bottom-up shade is a motorized roller shade that opens from top to bottom operating in the opposite direction of a conventional roller shade, so as to cover the bottom part of the window, while allowing daylight to enter from the top part of the window, reaching deeper into the room. A daylighting simulation model, validated with full-scale experiments, was developed in order to establish correlations between the shade position, outdoor illuminance and work plane illuminance for different outdoor conditions. Then, a shading control algorithm was developed for application in any location and orientation. The validated model was employed for a sensitivity analysis of the impact of shade optical properties and control on the potential energy savings due to the use of daylighting. The results showed that Daylight Autonomy for the bottom-up shade is 8-58% higher compared to a conventional roller shade, with a difference of 46% further away from the facade, where the use of electric lighting is needed most of the time. The potential reduction in energy consumption for lighting is 21-41%. (author)

  1. High Speed Cylindrical Roller Bearing Analysis, SKF Computer Program CYBEAN. Volume 1: Analysis

    NASA Technical Reports Server (NTRS)

    Kleckner, R. J.; Pirvics, J.

    1978-01-01

    The CYBEAN (CYlindrical BEaring ANalysis) program was created to detail radially loaded, aligned and misaligned Cylindrical roller bearing performance under a variety of operating conditions. The models and associated mathematics used within CYBEAN are described. The user is referred to the material for formulation assumptions and algorithm detail.

  2. The Roller-Coaster of Experiences: Becoming the Parent of a Deaf Child

    ERIC Educational Resources Information Center

    Bosteels, Sigrid; Van Hove, Geert; Vandenbroeck, Michel

    2012-01-01

    When early testing indicates a hearing loss, parents find themselves on a roller-coaster of experiences leaving little time or space for reflection. This study is based on interviews with families in the Flemish region of Belgium, one of the earliest in the world to introduce universal neonatal screening for hearing loss. Starting from a…

  3. Acceleration in One, Two, and Three Dimensions in Launched Roller Coasters

    ERIC Educational Resources Information Center

    Pendrill, Ann-Marie

    2008-01-01

    During a roller coaster ride, the body experiences acceleration in three dimensions. An accelerometer can measure and provide a graph of the forces on the body during different parts of a ride. To couple the experience of the body to pictures of the ride and an analysis of data can contribute to a deeper understanding of Newton's laws. This…

  4. Knee joint position sense of roller hockey players: a comparative study.

    PubMed

    Venâncio, João; Lopes, Diogo; Lourenço, Joaquim; Ribeiro, Fernando

    2016-06-01

    This study aimed to compare knee joint position sense of roller hockey players with an age-matched group of non-athletes. Forty-three male participants voluntarily participated in this cross-sectional study: 21 roller hockey players (mean age: 23.2 ± 4.2 years old, mean weight: 81.8 ± 9.8 kg, mean height: 180.5 ± 4.1 cm) and 22 age-matched non-athletes (mean age: 23.7 ± 3.9 years old, mean weight: 85.0 ± 6.2 kg, mean height: 181.5 ± 5.0 cm). Knee joint position sense of the dominant limb was evaluated using a technique of open-kinetic chain and active knee positioning. Joint position sense was reported using absolute, relative and variable angular errors. The main results indicated that the group of roller hockey players showed significantly lower absolute (2.4 ± 1.2º vs. 6.5 ± 3.2º, p ≤ 0.001) and relative (1.7 ± 2.1º vs. 5.8 ± 4.4º, p ≤ 0.001) angular errors in comparison with the non-athletes group. In conclusion, the results from this present study suggest that proprioceptive acuity, assessed by measuring joint position sense, is increased in roller hockey players. The enhanced proprioception of the roller hockey players could contribute to injury prevention and improved performance during sporting activities. PMID:27111126

  5. Nest ecology of blood parasites in the European roller and its ectoparasitic carnid fly.

    PubMed

    Václav, Radovan; Betáková, Tatiana; Švančarová, Petra; Pérez-Serrano, Jorge; Criado-Fornelio, Ángel; Škorvanová, Lucia; Valera, Francisco

    2016-06-01

    Haemosporidian parasites are considered the most important vector-borne parasites. However, vector identity and ecology is unknown for most such host-vector-parasite systems. In this study, we employ microscopic and molecular analyses to examine haemosporidian prevalence in a migratory, cavity-nesting bird, European roller Coracias garrulus, and its nidicolous blood-feeding ectoparasite Carnus hemapterus. This system is unique in that the ectoparasite is confined to a near-closed environment, in contrast to the free-wandering system of haematophagous dipterans such as mosquitoes. Blood film analysis confirms previous works in that Haemoproteus parasites are widely prevalent in adult rollers and belong to a single species, Haemoproteus coraciae. Leucocytozoon sp. and Trypanosoma sp. also are detected in adult rollers at low intensities with this technique. By means of molecular analysis, we report for the first time Plasmodium sp. presence in C. garrulus. Based on PCR results, Plasmodium parasites are relatively less prevalent than Haemoproteus parasites (20% vs. 31%) in rollers. In contrast, haemosporidian prevalences show the opposite trend for Carnus flies: Plasmodium sp. occurrence (62%) clearly predominates over that of Haemoproteus sp. (5%). A comparison between roller and Carnus samples reveals a significantly higher prevalence of Plasmodium sp. in Carnus samples. Insect survey and phylogenetic analysis suggest Culicoides flies as Haemoproteus sp. vectors, which appear to readily transmit the parasite in southern Spain. This study does not find support for Carnus flies to serve as biological or mechanical vectors of haemosporidians. In spite of this, nidicolous blood-feeding ectoparasites, such as carnid flies, appear as a suitable model for studies on the occurrence and temporal dynamics of avian haemosporidians such as Plasmodium sp. present at low intensities. PMID:26993083

  6. Technical development of double-clad process for thin strip casting of carbon steel

    SciTech Connect

    Brown, H.L.; Forkel, C.E.; Knudson, D.L.

    1984-08-01

    This report documents the technical development for a patent disclosure of a double-clad process for the continuous casting of thin-strip carbon steel. The fundamental idea of the disclosure is to form a product strip by depositing molten steel between two, cooled, clad strips of the same material. The claimed benefits include: (a) the conservation of energy in steel making through the elimination of soaking pits and reheat cycles, and (b) an improved surface on both sides of the as-cast product such that it will be suitable for direct feed to a cold-reduction mill. However, the process as conceived is not necessarily limited to the casting of carbon steel, but may be also applied to other metals and alloys. The work is described under three headings as follows. Preliminary Considerations and Scoping Analysis presents the basic idea of the double-clad, thin-strip casting process; the energy conservation potential; scoping heat transfer calculations for the casting process; and independent review of this work. Thermal Analysis for Roller Configuration of Double-Clad Process, presents the development, results, and independent review of a finite-element thermal analysis for the casting process as originally conceived (using only chilled rollers in direct contact with the clad material of the product strip). Further Considerations for Belt Configuration of Double-Clad Process deals with a modified equipment design which interposes two product support belts, one on each side of the product, between the clad strip and the rollers. In addition to the process description, this section presents the preliminary mechanical calculations for the endless metal belts and the work scope and results for the computer model revision and thermal analysis for the modified concept.

  7. Fire ants protect mealybugs against their natural enemies by utilizing the leaf shelters constructed by the leaf roller Sylepta derogata.

    PubMed

    Zhou, Aiming; Zeng, Ling; Lu, Yongyue; Xu, Yijuan; Liang, Guangwen

    2012-01-01

    The importance of mutualism is receiving more attention in community ecology. In this study, the fire ant Solenopsis invicta was found to take advantage of the shelters constructed by the leaf roller Sylepta derogata to protect mealybugs (Phenacoccus solenopsis) against their natural enemies. This protective effect of fire ant tending on the survival of mealybugs in shelters was observed when enemies and leaf rollers were simultaneously present. Specifically, fire ants moved the mealybugs inside the shelters produced by S. derogata on enemy-infested plants. Compared with that in plants without ants, the survival of mealybugs in shelters in the presence of natural enemies in plants with ants markedly improved. Both the protection of ants and the shelters provided by leaf rollers did not affect the survival of mealybugs in the absence of enemies in plants. Ants and leaf rollers significantly improved the survival of mealybugs in predator-infested plants, whereas no such improvement was observed in parasitoid-infested ones.

  8. Acute, fatal Sarcocystis calchasi-associated hepatitis in Roller pigeons (Columbia livia f. dom.) at Philadelphia Zoo

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Four Roller pigeons (Columba livia f. dom.) at the Philadelphia Zoo died suddenly. Necropsy examination revealed macroscopic hepatitis. Microscopically, the predominant lesions were in liver, characterized with necrosis and mixed cell inflammatory response. Sarcocystis calchasi-like schizonts and fr...

  9. Effect of Internal Clearance on Load Distribution and Life of Radially Loaded Ball and Roller Bearings

    NASA Technical Reports Server (NTRS)

    Oswald, Fred B.; Zaretsky, Erwin V.; Poplawski, Joseph V.

    2012-01-01

    The effect of internal clearance on radially loaded deepgroove ball and cylindrical roller bearing load distribution and fatigue life was determined for four clearance groups defined in the bearing standards. The analysis was extended to negative clearance (interference) conditions to produce a curve of life factor versus internal clearance. Rolling-element loads can be optimized and bearing life maximized for a small negative operating clearance. Life declines gradually with positive clearance and rapidly with increasing negative clearance. Relationships were found between bearing life and internal clearance as a function of ball or roller diameter, adjusted for load. Results are presented as life factors for radially loaded bearings independent of bearing size or applied load. In addition, a modified Stribeck Equation is presented that relates the maximum rolling-element load to internal bearing clearance.

  10. Pervasive liquid metal based direct writing electronics with roller-ball pen

    SciTech Connect

    Zheng, Yi; Zhang, Qin; Liu, Jing

    2013-11-15

    A roller-ball pen enabled direct writing electronics via room temperature liquid metal ink was proposed. With the rolling to print mechanism, the metallic inks were smoothly written on flexible polymer substrate to form conductive tracks and electronic devices. The contact angle analyzer and scanning electron microscope were implemented to disclose several unique inner properties of the obtained electronics. An ever high writing resolution with line width and thickness as 200 μm and 80 μm, respectively was realized. Further, with the administration of external writing pressure, GaIn{sub 24.5} droplets embody increasing wettability on polymer which demonstrates the pervasive adaptability of the roller-ball pen electronics.

  11. Micromagnetic simulation of thermal ripple in thin films: ``Roller-coaster'' visualization

    NASA Astrophysics Data System (ADS)

    Feng, Xuebing; Visscher, P. B.; Apalkov, D. M.

    2003-05-01

    We present simulations of pulse-induced magnetization-rotation experiments in Permalloy. These lead to temporary domain formation ("thermal ripple") and help to explain the time dependence of experimental results. To understand and visualize the motion, we find it very useful to exploit a mathematical isomorphism of this problem (in the limit Ms≫Hpulse) to the problem of a massive particle on a circular track ("roller coaster"). The height (gravitational potential energy) of this track is proportional to the Stoner-Wohlfarth energy. The fact that the resulting "precession" is really oscillation in a plane, and the fact that this oscillation overshoots the minimum-energy configuration (the inertia effect) are much more intuitive in the roller coaster picture than in the conventional "M precesses about the effective field" picture. Animated simulations of this behavior are available on the web (http://bama.ua.edu/˜visscher/mumag/).

  12. Resolution of sudden sensorineural hearing loss following a roller coaster ride.

    PubMed

    Kumar, Aman; Sinha, Amrita; Al-Waa, Ahmad M

    2011-07-01

    We report a case of sudden unilateral sensorineural hearing loss of sudden onset during an aeroplane flight, which completely resolved during a roller coaster ride at Alton Towers theme park. A review of the literature concerning sudden idiopathic sensorineural hearing loss and spontaneous resolution are discussed. Initially, pure-tone audiometry showed a profound sensorineural hearing loss in the right ear and mild sensorineural hearing loss in the left ear (of note, the hearing was normal prior to the episode). Following resolution of the patient's symptoms during a roller coaster ride, pure-tone audiometry showed normal hearing thresholds in both ears. Sudden sensorineural hearing loss is a symptom of cochlear injury and the mechanism of the patient's symptoms was attributed to a patent cochlear aqueduct. PMID:22754856

  13. Pervasive liquid metal based direct writing electronics with roller-ball pen

    NASA Astrophysics Data System (ADS)

    Zheng, Yi; Zhang, Qin; Liu, Jing

    2013-11-01

    A roller-ball pen enabled direct writing electronics via room temperature liquid metal ink was proposed. With the rolling to print mechanism, the metallic inks were smoothly written on flexible polymer substrate to form conductive tracks and electronic devices. The contact angle analyzer and scanning electron microscope were implemented to disclose several unique inner properties of the obtained electronics. An ever high writing resolution with line width and thickness as 200 μm and 80 μm, respectively was realized. Further, with the administration of external writing pressure, GaIn24.5 droplets embody increasing wettability on polymer which demonstrates the pervasive adaptability of the roller-ball pen electronics.

  14. Statistical model and control of a ring-and-roller type grinding mill

    SciTech Connect

    Cho, S.

    1992-01-01

    This project explores the use of a ring-and-roller grinding mill for fine grinding or pulverizing. Since the efficiency of this system is low, small improvements in product throughput or energy consumption can result in substantial economic improvements. To better understand this system, experiments were conducted for limestone and cement clinker. From these experiments models were formulated for product throughput, energy consumption and product size distribution. A control loop was implemented to reduce the effect of non-uniform feeding. Steady-state interactions were analyzed using the Relative Gain Array (RGA) method. Next, a multi-input and multi-output (MIMO) control system was designed using the Inverse Nyquist Array (INA) method to remove variable interactions. The robustness of this controller was explored. Finally, a self-tuning PI controller was designed using the pole placement method to improve system performance. The results of this study provide models for implementation on ring-and-roller grinding mills.

  15. Resolution of sudden sensorineural hearing loss following a roller coaster ride.

    PubMed

    Kumar, Aman; Sinha, Amrita; Al-Waa, Ahmad M

    2011-07-01

    We report a case of sudden unilateral sensorineural hearing loss of sudden onset during an aeroplane flight, which completely resolved during a roller coaster ride at Alton Towers theme park. A review of the literature concerning sudden idiopathic sensorineural hearing loss and spontaneous resolution are discussed. Initially, pure-tone audiometry showed a profound sensorineural hearing loss in the right ear and mild sensorineural hearing loss in the left ear (of note, the hearing was normal prior to the episode). Following resolution of the patient's symptoms during a roller coaster ride, pure-tone audiometry showed normal hearing thresholds in both ears. Sudden sensorineural hearing loss is a symptom of cochlear injury and the mechanism of the patient's symptoms was attributed to a patent cochlear aqueduct.

  16. A roller-like bird (Coracii) from the Early Eocene of Denmark

    PubMed Central

    Bourdon, Estelle; Kristoffersen, Anette V.; Bonde, Niels

    2016-01-01

    The fossil record of crown group birds (Neornithes) prior to the Cretaceous-Paleogene boundary is scarce and fragmentary. Early Cenozoic bird fossils are more abundant, but are typically disarticulated and/or flattened. Here we report the oldest roller (Coracii), Septencoracias morsensis gen. et sp. nov. (Primobucconidae), based on a new specimen from the Early Eocene (about 54 million years ago) Fur Formation of Denmark. The new fossil is a nearly complete, three-dimensionally preserved and articulated skeleton. It lies at the lower end of the size range for extant rollers. Salient diagnostic features of Septencoracias relative to other Coracii include the proportionally larger skull and the small, ovoid and dorsally positioned narial openings. Our discovery adds to the evidence that the Coracii had a widespread northern hemisphere distribution in the Eocene. Septencoracias is the oldest substantial record of the Picocoraciae and provides a reliable calibration point for molecular phylogenetic studies. PMID:27670387

  17. Acceleration in one, two, and three dimensions in launched roller coasters

    NASA Astrophysics Data System (ADS)

    Pendrill, Ann-Marie

    2008-09-01

    During a roller coaster ride, the body experiences acceleration in three dimensions. An accelerometer can measure and provide a graph of the forces on the body during different parts of a ride. To couple the experience of the body to pictures of the ride and an analysis of data can contribute to a deeper understanding of Newton's laws. This article considers the physics of launched roller coasters. Measurements were performed with a three-dimensional co-moving accelerometer. An analysis is presented of the forces in the different ride elements of the Kanonen in Göteborg and the Speed Monster in Oslo, which both include loops and offer rich examples of force and acceleration in all dimensions.

  18. Compressed sensing of roller bearing fault based on multiple down-sampling strategy

    NASA Astrophysics Data System (ADS)

    Wang, Huaqing; Ke, Yanliang; Luo, Ganggang; Tang, Gang

    2016-02-01

    Roller bearings are essential components of rotating machinery and are often exposed to complex operating conditions, which can easily lead to their failures. Thus, to ensure normal production and the safety of machine operators, it is essential to detect the failures as soon as possible. However, it is a major challenge to maintain a balance between detection efficiency and big data acquisition given the limitations of sampling theory. To overcome these limitations, we try to preserve the information pertaining to roller bearing failures using a sampling rate far below the Nyquist sampling rate, which can ease the pressure generated by the large-scale data. The big data of a faulty roller bearing’s vibration signals is firstly reduced by a down-sample strategy while preserving the fault features by selecting peaks to represent the data segments in time domain. However, a problem arises in that the fault features may be weaker than before, since the noise may be mistaken for the peaks when the noise is stronger than the vibration signals, which makes the fault features unable to be extracted by commonly-used envelope analysis. Here we employ compressive sensing theory to overcome this problem, which can make a signal enhancement and reduce the sample sizes further. Moreover, it is capable of detecting fault features from a small number of samples based on orthogonal matching pursuit approach, which can overcome the shortcomings of the multiple down-sample algorithm. Experimental results validate the effectiveness of the proposed technique in detecting roller bearing faults.

  19. Dynamic and thermal analysis of high speed tapered roller bearings under combined loading

    NASA Technical Reports Server (NTRS)

    Crecelius, W. J.; Milke, D. R.

    1973-01-01

    The development of a computer program capable of predicting the thermal and kinetic performance of high-speed tapered roller bearings operating with fluid lubrication under applied axial, radial and moment loading (five degrees of freedom) is detailed. Various methods of applying lubrication can be considered as well as changes in bearing internal geometry which occur as the bearing is brought to operating speeds, loads and temperatures.

  20. Rereading "The Jack-Roller:" Hidden Histories in Sociology and Social Work

    ERIC Educational Resources Information Center

    Shaw, Ian

    2009-01-01

    I revisit one of the iconic Chicago School studies, Clifford Shaw's "The Jack-Roller". A naive reading of Shaw's book leaves the reader with a sense of having been inducted into a melange of what we now know as "sociology" and "social work," but which to Shaw seems a coherent stance. I suggest that this is close to the heart of how things were,…

  1. Optimization of Spherical Roller Bearing Design Using Artificial Bee Colony Algorithm and Grid Search Method

    NASA Astrophysics Data System (ADS)

    Tiwari, Rajiv; Waghole, Vikas

    2015-07-01

    Bearing standards impose restrictions on the internal geometry of spherical roller bearings. Geometrical and strength constraints conditions have been formulated for the optimization of bearing design. The long fatigue life is one of the most important criteria in the optimum design of bearing. The life is directly proportional to the dynamic capacity; hence, the objective function has been chosen as the maximization of dynamic capacity. The effect of speed and static loads acting on the bearing are also taken into account. Design variables for the bearing include five geometrical parameters: the roller diameter, the roller length, the bearing pitch diameter, the number of rollers, and the contact angle. There are a few design constraint parameters which are also included in the optimization, the bounds of which are obtained by initial runs of the optimization. The optimization program is made to run for different values of these design constraint parameters and a range of the parameters is obtained for which the objective function has a higher value. The artificial bee colony algorithm (ABCA) has been used to solve the constrained optimized problem and the optimum design is compared with the one obtained from the grid search method (GSM), both operating independently. Both the ABCA and the GSM have been finally combined together to reach the global optimum point. A constraint violation study has also been carried out to give priority to the constraint having greater possibility of violations. Optimized bearing designs show a better performance parameter with those specified in bearing catalogs. The sensitivity analysis of bearing parameters has also been carried out to see the effect of manufacturing tolerance on the objective function.

  2. Calculated and experimental data for a 118-mm bore roller bearing to 3 million DN

    NASA Technical Reports Server (NTRS)

    Coe, H. H.; Schuller, F. T.

    1980-01-01

    The operating characteristics for 118 mm bore cylindrical roller bearing are examined using the computer program CYBEAN. The predicted results of inner and outer-race temperatures and heat transferred to the lubricant generally compared well with experimental data for shaft speeds to 3 million DN (25,000 rpm), radial loads to 8900 N (2000 lb), and total lubricant flow rates to 0.0102 cu m/min (2.7 gal/min).

  3. Clinical use of centrifugal pumps and the roller pump in open heart surgery: a comparative evaluation.

    PubMed

    Yoshikai, M; Hamada, M; Takarabe, K; Okazaki, Y; Ito, T

    1996-06-01

    Centrifugal pumps have been used widely as the main pump in open heart surgery to reduce damage to blood elements and to reduce the activation of the coagulation system. The purpose of this study was the evaluation and comparison of the effects of two types of centrifugal pumps and of one type of roller pump on blood elements, the coagulation system, complements, and immunoglobulins. Two types of centrifugal pumps (Lifestream; St. Jude Medical, Chelmsford, Massachusetts; and BP-80: Medtronic, BioMedicus, Inc., Eden Prairie, Minnesota, U.S.A.) and one roller pump (Mera Co.) were used separately as the main pump for cardiopulmonary bypass (CPB) in 29 patients. Platelet counts, lactate dehydrogenase, antithrombin III, thrombin-antithrombin complex (TAT), complements (C3, C4, and CH50) and immunoglobulins G, A, and M values were measured before and after CPB and compared. Values, except those for TAT, showed no significant difference among the three groups. The TAT values increased less in each of the centrifugal pump groups than in the roller pump group. This finding suggests that thrombin synthesis might be suppressed by the use of a centrifugal pump.

  4. Evaluation of a high-torque backlash-free roller actuator

    NASA Technical Reports Server (NTRS)

    Steinetz, Bruce M.; Rohn, Douglas A.; Anderson, William

    1986-01-01

    The results are presented of a test program that evaluated the stiffness, accuracy, torque ripple, frictional losses, and torque holding capability of a 16:1 ratio, 430 N-m (320 ft-lb) planetary roller drive for a potential space vehicle actuator application. The drive's planet roller supporting structure and bearings were found to be the largest contributors to overall drive compliance, accounting for more than half of the total. In comparison, the traction roller contacts themselves contributed only 9 percent of the drive's compliance based on an experimentally verified stiffness model. The drive exhibited no backlash although 8 arc sec of hysteresis deflection were recorded due to microcreep within the contact under torque load. Because of these load-dependent displacements, some form of feedback control would be required for arc second positioning applications. Torque ripple tests showed the drive to be extremely smooth, actually providing some damping of input torsional oscillations. The drive also demonstrated the ability to hold static torque with drifts of 7 arc sec or less over a 24 hr period at 35 percent of full load.

  5. Roller and Centrifugal Pumps: A Retrospective Comparison of Bleeding Complications in Extracorporeal Membrane Oxygenation.

    PubMed

    Halaweish, Ihab; Cole, Adam; Cooley, Elaine; Lynch, William R; Haft, Jonathan W

    2015-01-01

    Centrifugal pumps are increasingly used for extracorporeal membrane oxygenation (ECMO) rather than roller pumps. However, shear forces induced by these types of continuousflow pumps are associated with acquired von Willebrand factor deficiency and bleeding complications. This study was undertaken to compare adverse bleeding complications with the use of centrifugal and roller pumps in patients on prolonged ECMO support. The records of all adult ECMO patients from June 2002 to 2013 were retrospectively reviewed using the University of Michigan Health System database and the Extracorporeal Life Support Organization registry, focusing on patients supported for at least 5 days. Ninety-five ECMO patients met criteria for inclusion (48 roller vs. 47 centrifugal pump). Indications included pulmonary (79%), cardiac (15%), and extracorporeal cardiopulmonary resuscitation (6%), without significant difference between the two groups. Despite lower heparin anticoagulation (10.9 vs. 13.7 IU/kg/hr) with centrifugal pumps, there was a higher incidence of nonsurgical bleeding (gastrointestinal, pulmonary, and neurological) in centrifugal pump patients (26.1 vs. 9.0 events/1,000 patient-days, p = 0.024). In conclusion, in our historical comparison, despite reduced anticoagulation, ECMO support using centrifugal pumps was associated with a higher incidence of nonsurgical bleeding. The mechanisms behind this are multifactorial and require further investigation.

  6. Delta efficiency of uphill roller skiing with the double pole and diagonal stride techniques.

    PubMed

    Hoffman, M D; Clifford, P S; Watts, P B; O'Hagan, K P; Mittelstadt, S W

    1995-12-01

    Delta efficiencies for uphill roller skiing with the double pole (DP) and diagonal stride (DS) techniques were determined among 4 female and 4 male cross-country ski racers in order to examine for differences between techniques and between the sexes. Each skier roller-skied on a motorized ski-treadmill at 1.7% and 7.1% grades with both techniques at 2 to 4 different speeds. Steady-state oxygen uptake values were used to calculate the differences in metabolic requirements for roller skiing at the 2 grades (delta E). The differences in external work rates between the 2 grades (delta W) were calculated from the work rates for overcoming rolling resistance and elevating the transported mass against gravity. Delta efficiencies (delta W/ delta E) ranged from 14 to 36%, were significantly greater (p < 0.001) for DS than DP, and showed a significant (p < 0.01) velocity effect for DS. Delta efficiencies were 27% greater (p < 0.05) for the women compared with the men for DP, and significant (p < 0.05) correlations were found between efficiency for DP and body mass. This suggests that the higher efficiency with DP for female skiers is at least partially due to their lower body mass.

  7. Forces and mechanical energy fluctuations during diagonal stride roller skiing; running on wheels?

    PubMed

    Kehler, Alyse L; Hajkova, Eliska; Holmberg, Hans-Christer; Kram, Rodger

    2014-11-01

    Mechanical energy can be conserved during terrestrial locomotion in two ways: the inverted pendulum mechanism for walking and the spring-mass mechanism for running. Here, we investigated whether diagonal stride cross-country roller skiing (DIA) utilizes similar mechanisms. Based on previous studies, we hypothesized that running and DIA would share similar phase relationships and magnitudes of kinetic energy (KE), and gravitational potential energy (GPE) fluctuations, indicating elastic energy storage and return, as if roller skiing is like 'running on wheels'. Experienced skiers (N=9) walked and ran at 1.25 and 3 m s(-1), respectively, and roller skied with DIA at both speeds on a level dual-belt treadmill that recorded perpendicular and parallel forces. We calculated the KE and GPE of the center of mass from the force recordings. As expected, the KE and GPE fluctuated with an out-of-phase pattern during walking and an in-phase pattern during running. Unlike walking, during DIA, the KE and GPE fluctuations were in phase, as they are in running. However, during the glide phase, KE was dissipated as frictional heat and could not be stored elastically in the tendons, as in running. Elastic energy storage and return epitomize running and thus we reject our hypothesis. Diagonal stride cross-country skiing is a biomechanically unique movement that only superficially resembles walking or running.

  8. Design and Operating Characteristics of High-Speed, Small-Bore Cylindrical-Roller Bearings

    NASA Technical Reports Server (NTRS)

    Pinel, Stanley, I.; Signer, Hans R.; Zaretsky, Erwin V.

    2000-01-01

    The computer program SHABERTH was used to analyze 35-mm-bore cylindrical roller bearings designed and manufactured for high-speed turbomachinery applications. Parametric tests of the bearings were conducted on a high-speed, high-temperature bearing tester and the results were compared with the computer predictions. Bearings with a channeled inner ring were lubricated through the inner ring, while bearings with a channeled outer ring were lubricated with oil jets. Tests were run with and without outer-ring cooling. The predicted bearing life decreased with increasing speed because of increased contact stresses caused by centrifugal load. Lower temperatures, less roller skidding, and lower power losses were obtained with channeled inner rings. Power losses calculated by the SHABERTH computer program correlated reasonably well with the test results. The Parker formula for XCAV (used in SHABERTH as a measure of oil volume in the bearing cavity) needed to be adjusted to reflect the prevailing operating conditions. The XCAV formula will need to be further refined to reflect roller bearing lubrication, ring design, cage design, and location of the cage-controlling land.

  9. Elevated-temperature fracture toughness and fatigue testing of steels for geothermal applications. Annual progress report

    SciTech Connect

    Cutler, R.A.; Goodman, E.C.; Guest, R.V.; Hendrickson, R.R.; Leslie, W.C.

    1980-11-01

    Conventional drill bit steels exhibit increased wear and decreased toughness when run at elevated temperatures in geothermal wells. Bits are therefore run at lower speeds and lighter loads, resulting in lower penetration rates for geothermal wells than for conventional rock drilling. Carpenter EX-00053, Timken CBS 600, Timken CBS 1000M and Vasco X-2M, steels with improved hot hardness (improved wear resistance), were tested in conjunction with the steels used for cones (AISI 4820 and 9315) and lugs (AISI 8620 and 9315) in conventional roller cone rock bits. Shortrod fracture toughness measurements were made on each of these steels between room temperature and 400/sup 0/C. Fatigue crack resistance was determined at 300/sup 0/C for high-temperature steels and at room temperature for conventional steels. Scanning electron microscopy analyses of the fractured short-rod specimens were correlated with observed crack behavior from the test records. Test results are discussed, recommendations made for further testing and preliminary steel selections made for improved geothermal bits.

  10. A Numerical Algorithm for Determining the Contact Stress of Circular Crowned Roller Compressed between Two Flat Plates

    NASA Astrophysics Data System (ADS)

    Horng, Thin-Lin

    The main purpose of this paper is to explore a numerical algorithm for determining the contact stress when a circular crowned roller is compressed between two plates. To start with, the deformation curve on a plate surface will be derived by using the contact mechanical model. Then, the contact stress distribution along the roller which occurs on the plate surface is divided into three parts: from the center of contact to the edge, the edge and apart from the contact line. The first part is calculated by the elastic contact theorem for the contact subjected to nominal stress between non-crowned parts of roller and plates, the second part is obtained by the classical Hertzian contact solution for the contact between crowned parts of roller and plates, and the third part is simulated as exponential decay. In order to overcome the defect of the half space theorem, in which a plate with infinite thickness is assumed initially, a weighting method is introduced to find the contact stress of the plate with finite thickness. Comparisons with various finite element results indicate that the algorithm for estimating the contact stress of a circular crowned roller compressed between two plates derived in this paper can be a reasonably accurate when a heavy displacement load is applied. This is because the contact area is large under a heavy load, and the effect of stress concentration is smaller in comparison with the case under a light load.

  11. Fabrication of a roller type PDMS stamp using SU-8 concave molds and its application for roll contact printing

    NASA Astrophysics Data System (ADS)

    Park, Jongho; Kim, Beomjoon

    2016-03-01

    Continuous fabrication of micropatterns at low-cost is attracting attention in various applications within industrial fields. To meet such demands, we have demonstrated a roll contact printing technique, using roller type polydimethylsiloxane (PDMS) stamps with roll-to-flat and roll-to-roll stages. Roller type PDMS stamps for roll contact printing were fabricated using a custom-made metal support and SU-8 microstructures fabricated on concave substrates as a mold. The molding/casting method which we developed here provided faster and easier fabrication than conventional methods for roller type stamps. Next, roll contact printing was performed using fabricated roller type PDMS stamps with roll-to-flat and roll-to-roll stages. Patterns with minimum widths of 3 μm and 2.1 μm were continuously fabricated for each stage, respectively. In addition, the relationship between applied pressures and dimensional changes of roll contact printed patterns was investigated. Finally, we confirmed that roll contact printing and the new fabrication method for roller stamps presented in this study demonstrated the feasibility for industrial applications.

  12. A new computational fluid dynamics method for in-depth investigation of flow dynamics in roller pump systems.

    PubMed

    Zhou, Xiaoming; Liang, Xin M; Zhao, Gang; Su, Youchao; Wang, Yang

    2014-07-01

    Roller pumps are commonly used in circulatory assist devices to deliver blood, but the inherent high mechanical stresses (especially wall shear stress) may cause considerable damage to cells. Conventional experimental approaches to evaluate and reduce device-induced cell damage require considerable effort and resources. In this work, we describe the use of a new computational fluid dynamics method to more effectively study roller pump systems. A generalized parametric model for the fluid field in a typical roller pump system is presented first, and analytical formulations of the moving boundary are then derived. Based on the model and formulations, the dynamic geometry and mesh of the fluid field can be updated automatically according to the time-dependent roller positions. The described method successfully simulated the pulsing flow generated by the pump, offering a convenient way to visualize the inherent flow pattern and to assess shear-induced cell damage. Moreover, the highly reconfigurable model and the semiautomated simulation process extend the usefulness of the presented method to a wider range of applications. Comparison studies were conducted, and valuable indications about the detailed effects of structural parameters and operational conditions on the produced wall shear stress were obtained. Given the good consistency between the simulated results and the existing experimental data, the presented method displays promising potential to more effectively guide the development of improved roller pump systems which produce less mechanical damage to cells.

  13. Corrective action decision document for the Roller Coaster Lagoons and North Disposal Trench (Corrective Action Unit Number 404)

    SciTech Connect

    1997-03-26

    The North Disposal Trench, located north of the eastern most lagoon, was installed in 1963 to receive solid waste and construction debris from the Operation Roller Coaster man camp. Subsequent to Operation Roller Coaster, the trench continued to receive construction debris and range cleanup debris (including ordnance) from Sandia National Laboratories and other operators. A small hydrocarbon spill occurred during Voluntary Corrective Action (VCA) activities (VCA Spill Area) at an area associated with the North Disposal Trench Corrective Action Site (CAS). Remediation activities at this site were conducted in 1995. A corrective action investigation was conducted in September of 1996 following the Corrective Action Investigation Plan (CAIP); the detailed results of that investigation are presented in Appendix A. The Roller Coaster Lagoons and North Disposal Trench are located at the Tonopah Test Range (TTR), a part of the Nellis Air Force Range, which is approximately 225 kilometers (140 miles) northwest of Las Vegas, Nevada, by air.

  14. Analysis of crack propagation in roller bearings using the boundary integral equation method - A mixed-mode loading problem

    NASA Technical Reports Server (NTRS)

    Ghosn, L. J.

    1988-01-01

    Crack propagation in a rotating inner raceway of a high-speed roller bearing is analyzed using the boundary integral method. The model consists of an edge plate under plane strain condition upon which varying Hertzian stress fields are superimposed. A multidomain boundary integral equation using quadratic elements was written to determine the stress intensity factors KI and KII at the crack tip for various roller positions. The multidomain formulation allows the two faces of the crack to be modeled in two different subregions, making it possible to analyze crack closure when the roller is positioned on or close to the crack line. KI and KII stress intensity factors along any direction were computed. These calculations permit determination of crack growth direction along which the average KI times the alternating KI is maximum.

  15. A mathematical model describing the solid conveying and melting behavior of planetary roller extruders

    NASA Astrophysics Data System (ADS)

    Rudloff, J.; Lang, M.; Kretschmer, K.; Heidemeyer, P.; Bastian, M.; Koch, M.

    2014-05-01

    Due to increased quality requirements and the trend to cost reduction by process optimization, the modeling of plastic processing by means of simulation software becomes more and more important to predict process behavior. Most tools are based on a physical analysis of the process conditions and a reflection of those in a mathematical model, either based on FE methods or an approach to approximation or complete analytical models. First models were published for planetary roller extruders. However, these models deal primarily with the melt conveying behavior and have not yet been developed for the melting process which in many cases is critical to address homogenization features of such machines in the melt phase. This paper presents an approach to calculate the melting degree along the barrel of a planetary roller extruder. Therefore, models that are used to describe the melting process of single and twin screw extruders are adjusted to the conditions in the planetary roller extruder. At first the relevant process was divided in the three steps solid conveying, melting initiation and melting propagation. The solid conveying is described by the Archimedes solid conveying model. In order to estimate the melting initiation the solid particles temperature increase was used for partial filled sections. Further, it was assumed that the melting cannot start later than at the point where the extruder flow channels are fully filled for the first time. The melting propagation was described by a modified disperse melting model. The developed models were implemented into a simulation tool. The models were verified by experimental investigations. A comparison between simulated results and experimental data shows a good agreement.

  16. Anaerobic threshold assessment through the ventilatory method during roller-ski skating testing: right or wrong?

    PubMed

    Fabre, Nicolas; Bortolan, Lorenzo; Pellegrini, Barbara; Zerbini, Livio; Mourot, Laurent; Schena, Federico

    2012-02-01

    This study aimed at questioning the validity of the ventilatory method to determine the anaerobic threshold (respiratory compensation point [RCP]) during an incremental roller-ski skating test to exhaustion. Nine elite crosscountry skiers were evaluated. The skiers carried out an incremental roller-ski test on a treadmill with the V2 skating technique. Ventilatory parameters were continuously collected breath by breath, thanks to a portable gas exchange measurement system. Poling signal was obtained using instrumented ski poles. For each stage, ventilatory and poling signals were synchronized and averaged. The poor coefficient of interobserver reliability for the time at RCP confirmed the great difficulty felt by the 3 blinded reviewers for the RCP determination. Moreover, the reviewer agreed with the impossibility of determining RCP in 4 of the 9 skiers. There was no significant difference between breathing frequency (Bf) and poling frequency (Pf) during the last 8 stages. However, it seems that the differences observed during the first stages arose from the use of either a strictly 1:1 or a 1:2 Bf to Pf ratio when the exercise intensity was still moderate. So, even if there were significant differences between the frequencies, the Bf was strictly subordinate to the Pf during the entire test. In the same way, the normalized tidal volume and peak poling forces curves were superposable. These findings showed that when the upper body is mainly involved in the propulsion, the determinants of the ventilation are strictly dependent on the poling pattern during an incremental test to exhaustion. Thus, during roller-ski skating, the determination of RCP must be used cautiously because too much depending on mechanical factors.

  17. Serum ferritin and serum iron changes after cross-country and roller ski endurance races.

    PubMed

    Pattini, A; Schena, F; Guidi, G C

    1990-01-01

    We have studied the variations induced in iron status parameters by four endurance races of different lengths. A comprehensive group of 48 healthy, non-iron deficient, endurance athletes were evaluated before and after four different cross-country and roller ski races: I = Skirollonga, roller ski race for individuals (n = 10), mean duration (MD) = 1 h 48 min; II = Marcialonga, cross-country ski race for individuals (n = 9) MD = 3 h 10 min; III = 12-h of Caldonazzo (Trento-Italy) roller ski relay race (n = 13) MD = 12 h; IV = 24-h of Pinzolo (Trento-Italy) cross-country ski relay race (n = 16) MD = 24 h. In the relays the MD includes both exercise and recovery times. Blood samples were taken before and after every race for the determination of the following haematological parameters: red blood count, haemoglobin, and packed cell volume, serum iron concentration [SI], serum ferritin concentration [FERR] and total iron binding capacity (TIBC). The results showed a constant significant increase of [FERR] after the races (+44.9% in I, +50.5% in II, +51.2% in III and +36.5% in IV, P less than 0.01) while [SI] increased only in the first two races (+28.2% in I and +19.7% in II, P less than 0.01) and showed a remarkable decrease in the longer races (-46.1% in III and -39% in IV, P less than 0.01). The TIBC increased in all the races (except II) to the same extent (range 10%-12%).(ABSTRACT TRUNCATED AT 250 WORDS)

  18. Lubrication and Cooling Studies of Cylindrical-Roller Bearings at High Speeds

    NASA Technical Reports Server (NTRS)

    Macks, E Fred; Nemeth, Zolton N

    1952-01-01

    The results of an experimental investigation of the effect of oil inlet distribution and oil inlet temperature on the inner and outer-race temperatures of 75-millimeter-bore (size 215) cylindrical-roller inner-race-riding cage-type bearings are reported. A radial-load test rig was used over a range of dn values (product of the bearing bore in mm and the shaft speed in r.p.m) from 0.3 x 10(5) to 1.2 x 10(6) and static radial loads from 7 to 1113 pounds.

  19. Corrective Action Investigation Plan: Roller Coaster Lagoons and North Disposal Trench, Tonopah Test Range, Revision 1

    SciTech Connect

    IT Corporation, Las Vegas, NV

    1996-06-27

    1.1 Purpose The purpose of this investigation is to collect data to confirm the presence or absence of contamination, evaluate the potential for contaminant migration, and select appropriate closure methods for these sites. The potential closure methods for these sites involve either clean closure, closure in place, or no further action. 1.2 Scope The scope of this investigation includes collecting surface and subsurface soil samples at the Roller Coaster Lagoons; and collecting surface soil samples at the North Disposal Trench and the small spill area associated with the Voluntary Cotiective Action (VCA) that was conducted in 1995.

  20. How to apply life adjustment factors for ball and roller bearings.

    NASA Technical Reports Server (NTRS)

    Crecelius, W. J., Jr.; Harris, T. A.; Moyer, C. A.; Parker, R. J.; Zaretsky, E. V.; Sherlock, J. J.

    1972-01-01

    Practical problems applicable to the selection, design, and lubrication of rolling-element bearings are presented and discussed. The solutions to these problems are based upon the new ASME Engineering Design Guide - Life Adjustment Factors for Ball and Roller Bearings. Design and selection criteria are based upon materials and processing factors such as melting practice, metalworking, and heat treatment. Environmental factors considered include bearing misalignment and speed. Selection of a lubricant is based upon elastohydrodynamic lubrication principles in addition to lubricant type and chemistry.

  1. Physics and roller coasters-The Blue Streak at Cedar Point

    NASA Astrophysics Data System (ADS)

    Speers, Robert R.

    1991-06-01

    The use of a roller coaster for external classroom studies of kinematics, forces, dynamics, and energy conservation is discussed. Experimental accelerometer measurements of the vertical forces acting on riders of the Blue Streak at Cedar Point in Sandusky, Ohio are presented. Theoretically, the track profile is used to calculate/predict the vertical forces acting on a rider at the hilltops, valley bottoms, and several other points of interest along the track. Finally the experimental results and theoretical predictions are compared in the context of a rider's experiences.

  2. Profiled Roller Stress/Fatigue Life Analysis Methodology and Establishment of an Appropriate Stress/Life Exponent

    NASA Technical Reports Server (NTRS)

    1997-01-01

    The objective of this work was to determine the three dimensional volumetric stress field, surface pressure distribution and actual contact area between a 0.50" square roller with different crown profiles and a flat raceway surface using Finite Element Analysis. The 3-dimensional stress field data was used in conjunction with several bearing fatigue life theories to extract appropriate values for stress-life exponents. Also, results of the FEA runs were used to evaluate the laminated roller model presently used for stress and life prediction.

  3. Automatic Identification of Subtechniques in Skating-Style Roller Skiing Using Inertial Sensors.

    PubMed

    Sakurai, Yoshihisa; Fujita, Zenya; Ishige, Yusuke

    2016-01-01

    This study aims to develop and validate an automated system for identifying skating-style cross-country subtechniques using inertial sensors. In the first experiment, the performance of a male cross-country skier was used to develop an automated identification system. In the second, eight male and seven female college cross-country skiers participated to validate the developed identification system. Each subject wore inertial sensors on both wrists and both roller skis, and a small video camera on a backpack. All subjects skied through a 3450 m roller ski course using a skating style at their maximum speed. The adopted subtechniques were identified by the automated method based on the data obtained from the sensors, as well as by visual observations from a video recording of the same ski run. The system correctly identified 6418 subtechniques from a total of 6768 cycles, which indicates an accuracy of 94.8%. The precisions of the automatic system for identifying the V1R, V1L, V2R, V2L, V2AR, and V2AL subtechniques were 87.6%, 87.0%, 97.5%, 97.8%, 92.1%, and 92.0%, respectively. Most incorrect identification cases occurred during a subtechnique identification that included a transition and turn event. Identification accuracy can be improved by separately identifying transition and turn events. This system could be used to evaluate each skier's subtechniques in course conditions. PMID:27049388

  4. Performance of Integrated Systems of Automated Roller Shade Systems and Daylight Responsive Dimming Systems

    SciTech Connect

    Park, Byoung-Chul; Choi, An-Seop; Jeong, Jae-Weon; Lee, Eleanor S.

    2010-07-08

    Daylight responsive dimming systems have been used in few buildings to date because they require improvements to improve reliability. The key underlying factor contributing to poor performance is the variability of the ratio of the photosensor signal to daylight workplane illuminance in accordance with sun position, sky condition, and fenestration condition. Therefore, this paper describes the integrated systems between automated roller shade systems and daylight responsive dimming systems with an improved closed-loop proportional control algorithm, and the relative performance of the integrated systems and single systems. The concept of the improved closed-loop proportional control algorithm for the integrated systems is to predict the varying correlation of photosensor signal to daylight workplane illuminance according to roller shade height and sky conditions for improvement of the system accuracy. In this study, the performance of the integrated systems with two improved closed-loop proportional control algorithms was compared with that of the current (modified) closed-loop proportional control algorithm. In the results, the average maintenance percentage and the average discrepancies of the target illuminance, as well as the average time under 90percent of target illuminance for the integrated systems significantly improved in comparison with the current closed-loop proportional control algorithm for daylight responsive dimming systems as a single system.

  5. Underdetermined Blind Source Separation with Variational Mode Decomposition for Compound Roller Bearing Fault Signals.

    PubMed

    Tang, Gang; Luo, Ganggang; Zhang, Weihua; Yang, Caijin; Wang, Huaqing

    2016-01-01

    In the condition monitoring of roller bearings, the measured signals are often compounded due to the unknown multi-vibration sources and complex transfer paths. Moreover, the sensors are limited in particular locations and numbers. Thus, this is a problem of underdetermined blind source separation for the vibration sources estimation, which makes it difficult to extract fault features exactly by ordinary methods in running tests. To improve the effectiveness of compound fault diagnosis in roller bearings, the present paper proposes a new method to solve the underdetermined problem and to extract fault features based on variational mode decomposition. In order to surmount the shortcomings of inadequate signals collected through limited sensors, a vibration signal is firstly decomposed into a number of band-limited intrinsic mode functions by variational mode decomposition. Then, the demodulated signal with the Hilbert transform of these multi-channel functions is used as the input matrix for independent component analysis. Finally, the compound faults are separated effectively by carrying out independent component analysis, which enables the fault features to be extracted more easily and identified more clearly. Experimental results validate the effectiveness of the proposed method in compound fault separation, and a comparison experiment shows that the proposed method has higher adaptability and practicability in separating strong noise signals than the commonly-used ensemble empirical mode decomposition method. PMID:27322268

  6. Automatic Identification of Subtechniques in Skating-Style Roller Skiing Using Inertial Sensors

    PubMed Central

    Sakurai, Yoshihisa; Fujita, Zenya; Ishige, Yusuke

    2016-01-01

    This study aims to develop and validate an automated system for identifying skating-style cross-country subtechniques using inertial sensors. In the first experiment, the performance of a male cross-country skier was used to develop an automated identification system. In the second, eight male and seven female college cross-country skiers participated to validate the developed identification system. Each subject wore inertial sensors on both wrists and both roller skis, and a small video camera on a backpack. All subjects skied through a 3450 m roller ski course using a skating style at their maximum speed. The adopted subtechniques were identified by the automated method based on the data obtained from the sensors, as well as by visual observations from a video recording of the same ski run. The system correctly identified 6418 subtechniques from a total of 6768 cycles, which indicates an accuracy of 94.8%. The precisions of the automatic system for identifying the V1R, V1L, V2R, V2L, V2AR, and V2AL subtechniques were 87.6%, 87.0%, 97.5%, 97.8%, 92.1%, and 92.0%, respectively. Most incorrect identification cases occurred during a subtechnique identification that included a transition and turn event. Identification accuracy can be improved by separately identifying transition and turn events. This system could be used to evaluate each skier’s subtechniques in course conditions. PMID:27049388

  7. Fault Detection of Roller-Bearings Using Signal Processing and Optimization Algorithms

    PubMed Central

    Kwak, Dae-Ho; Lee, Dong-Han; Ahn, Jong-Hyo; Koh, Bong-Hwan

    2014-01-01

    This study presents a fault detection of roller bearings through signal processing and optimization techniques. After the occurrence of scratch-type defects on the inner race of bearings, variations of kurtosis values are investigated in terms of two different data processing techniques: minimum entropy deconvolution (MED), and the Teager-Kaiser Energy Operator (TKEO). MED and the TKEO are employed to qualitatively enhance the discrimination of defect-induced repeating peaks on bearing vibration data with measurement noise. Given the perspective of the execution sequence of MED and the TKEO, the study found that the kurtosis sensitivity towards a defect on bearings could be highly improved. Also, the vibration signal from both healthy and damaged bearings is decomposed into multiple intrinsic mode functions (IMFs), through empirical mode decomposition (EMD). The weight vectors of IMFs become design variables for a genetic algorithm (GA). The weights of each IMF can be optimized through the genetic algorithm, to enhance the sensitivity of kurtosis on damaged bearing signals. Experimental results show that the EMD-GA approach successfully improved the resolution of detectability between a roller bearing with defect, and an intact system. PMID:24368701

  8. The effects of the arm swing on biomechanical and physiological aspects of roller ski skating.

    PubMed

    Hegge, Ann Magdalen; Ettema, Gertjan; de Koning, Jos J; Rognstad, Asgeir Bakken; Hoset, Martin; Sandbakk, Øyvind

    2014-08-01

    This study analyzed the biomechanical and physiological effects of the arm swing in roller ski skating, and compared leg-skating (i.e. ski skating without poles) using a pronounced arm swing (SWING) with leg-skating using locked arms (LOCKED). Sixteen elite male cross-country skiers performed submaximal stages at 10, 15 and 20kmh(-1) on a 2% inclined treadmill in the two techniques. SWING demonstrated higher peak push-off forces and a higher force impulse at all speeds, but a longer cycle length only at the highest speed (all P<.05), indicating a lower force effectiveness with SWING at the two lowest speeds. Additionally, the flexion-extension movement in the lower limbs was more pronounced for SWING. Oxygen uptake was higher for SWING at the two lowest speeds (both P<.05) without any differences in blood lactate. At the highest speed, oxygen uptake did not differ between SWING and LOCKED, but the RER, blood lactate and ventilation were lower with SWING (all P<.05). Taken together, these results demonstrate that utilizing the arm swing in roller ski skating increases the ski forces and aerobic energy cost at low and moderate speeds, whereas the greater forces at high speed lead to a longer cycle length and smaller anaerobic contribution.

  9. Automatic Identification of Subtechniques in Skating-Style Roller Skiing Using Inertial Sensors.

    PubMed

    Sakurai, Yoshihisa; Fujita, Zenya; Ishige, Yusuke

    2016-04-02

    This study aims to develop and validate an automated system for identifying skating-style cross-country subtechniques using inertial sensors. In the first experiment, the performance of a male cross-country skier was used to develop an automated identification system. In the second, eight male and seven female college cross-country skiers participated to validate the developed identification system. Each subject wore inertial sensors on both wrists and both roller skis, and a small video camera on a backpack. All subjects skied through a 3450 m roller ski course using a skating style at their maximum speed. The adopted subtechniques were identified by the automated method based on the data obtained from the sensors, as well as by visual observations from a video recording of the same ski run. The system correctly identified 6418 subtechniques from a total of 6768 cycles, which indicates an accuracy of 94.8%. The precisions of the automatic system for identifying the V1R, V1L, V2R, V2L, V2AR, and V2AL subtechniques were 87.6%, 87.0%, 97.5%, 97.8%, 92.1%, and 92.0%, respectively. Most incorrect identification cases occurred during a subtechnique identification that included a transition and turn event. Identification accuracy can be improved by separately identifying transition and turn events. This system could be used to evaluate each skier's subtechniques in course conditions.

  10. Underdetermined Blind Source Separation with Variational Mode Decomposition for Compound Roller Bearing Fault Signals.

    PubMed

    Tang, Gang; Luo, Ganggang; Zhang, Weihua; Yang, Caijin; Wang, Huaqing

    2016-06-16

    In the condition monitoring of roller bearings, the measured signals are often compounded due to the unknown multi-vibration sources and complex transfer paths. Moreover, the sensors are limited in particular locations and numbers. Thus, this is a problem of underdetermined blind source separation for the vibration sources estimation, which makes it difficult to extract fault features exactly by ordinary methods in running tests. To improve the effectiveness of compound fault diagnosis in roller bearings, the present paper proposes a new method to solve the underdetermined problem and to extract fault features based on variational mode decomposition. In order to surmount the shortcomings of inadequate signals collected through limited sensors, a vibration signal is firstly decomposed into a number of band-limited intrinsic mode functions by variational mode decomposition. Then, the demodulated signal with the Hilbert transform of these multi-channel functions is used as the input matrix for independent component analysis. Finally, the compound faults are separated effectively by carrying out independent component analysis, which enables the fault features to be extracted more easily and identified more clearly. Experimental results validate the effectiveness of the proposed method in compound fault separation, and a comparison experiment shows that the proposed method has higher adaptability and practicability in separating strong noise signals than the commonly-used ensemble empirical mode decomposition method.

  11. A Sparsity-Promoted Decomposition for Compressed Fault Diagnosis of Roller Bearings

    PubMed Central

    Wang, Huaqing; Ke, Yanliang; Song, Liuyang; Tang, Gang; Chen, Peng

    2016-01-01

    The traditional approaches for condition monitoring of roller bearings are almost always achieved under Shannon sampling theorem conditions, leading to a big-data problem. The compressed sensing (CS) theory provides a new solution to the big-data problem. However, the vibration signals are insufficiently sparse and it is difficult to achieve sparsity using the conventional techniques, which impedes the application of CS theory. Therefore, it is of great significance to promote the sparsity when applying the CS theory to fault diagnosis of roller bearings. To increase the sparsity of vibration signals, a sparsity-promoted method called the tunable Q-factor wavelet transform based on decomposing the analyzed signals into transient impact components and high oscillation components is utilized in this work. The former become sparser than the raw signals with noise eliminated, whereas the latter include noise. Thus, the decomposed transient impact components replace the original signals for analysis. The CS theory is applied to extract the fault features without complete reconstruction, which means that the reconstruction can be completed when the components with interested frequencies are detected and the fault diagnosis can be achieved during the reconstruction procedure. The application cases prove that the CS theory assisted by the tunable Q-factor wavelet transform can successfully extract the fault features from the compressed samples. PMID:27657063

  12. Underdetermined Blind Source Separation with Variational Mode Decomposition for Compound Roller Bearing Fault Signals

    PubMed Central

    Tang, Gang; Luo, Ganggang; Zhang, Weihua; Yang, Caijin; Wang, Huaqing

    2016-01-01

    In the condition monitoring of roller bearings, the measured signals are often compounded due to the unknown multi-vibration sources and complex transfer paths. Moreover, the sensors are limited in particular locations and numbers. Thus, this is a problem of underdetermined blind source separation for the vibration sources estimation, which makes it difficult to extract fault features exactly by ordinary methods in running tests. To improve the effectiveness of compound fault diagnosis in roller bearings, the present paper proposes a new method to solve the underdetermined problem and to extract fault features based on variational mode decomposition. In order to surmount the shortcomings of inadequate signals collected through limited sensors, a vibration signal is firstly decomposed into a number of band-limited intrinsic mode functions by variational mode decomposition. Then, the demodulated signal with the Hilbert transform of these multi-channel functions is used as the input matrix for independent component analysis. Finally, the compound faults are separated effectively by carrying out independent component analysis, which enables the fault features to be extracted more easily and identified more clearly. Experimental results validate the effectiveness of the proposed method in compound fault separation, and a comparison experiment shows that the proposed method has higher adaptability and practicability in separating strong noise signals than the commonly-used ensemble empirical mode decomposition method. PMID:27322268

  13. Compressive Sensing of Roller Bearing Faults via Harmonic Detection from Under-Sampled Vibration Signals.

    PubMed

    Tang, Gang; Hou, Wei; Wang, Huaqing; Luo, Ganggang; Ma, Jianwei

    2015-10-09

    The Shannon sampling principle requires substantial amounts of data to ensure the accuracy of on-line monitoring of roller bearing fault signals. Challenges are often encountered as a result of the cumbersome data monitoring, thus a novel method focused on compressed vibration signals for detecting roller bearing faults is developed in this study. Considering that harmonics often represent the fault characteristic frequencies in vibration signals, a compressive sensing frame of characteristic harmonics is proposed to detect bearing faults. A compressed vibration signal is first acquired from a sensing matrix with information preserved through a well-designed sampling strategy. A reconstruction process of the under-sampled vibration signal is then pursued as attempts are conducted to detect the characteristic harmonics from sparse measurements through a compressive matching pursuit strategy. In the proposed method bearing fault features depend on the existence of characteristic harmonics, as typically detected directly from compressed data far before reconstruction completion. The process of sampling and detection may then be performed simultaneously without complete recovery of the under-sampled signals. The effectiveness of the proposed method is validated by simulations and experiments.

  14. 76 FR 43262 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-20

    ...: Initiation of Antidumping Duty New Shipper Review, 76 FR 6397 (February 4, 2011). On June 17, 2011, the... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the... (``NSR'') of Xiang Yang Automobile Bearing Co., Ltd. (``ZXY'').\\1\\ We gave interested parties...

  15. 76 FR 72213 - Tapered Roller Bearings From China; Notice of Commission determination To Conduct a Full Five...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-22

    ... part 201), and part 207, subparts A, D, E, and F (19 CFR part 207), as amended, 76 FR 61937 (October 6... responses to its notice of institution (76 FR 45853, August 1, 2011) were adequate.\\2\\ A record of the... COMMISSION Tapered Roller Bearings From China; Notice of Commission determination To Conduct a Full...

  16. 78 FR 45912 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-30

    ... the People's Republic of China, 52 FR 22667 (June 15, 1987). \\2\\ See Antidumping or Countervailing Duty Order, Finding, or Suspended Investigation; Opportunity to Request Administrative Review, 78 FR... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From...

  17. 77 FR 52682 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-30

    ... (Third Review), USITC Publication 4343 (August 2012), and Tapered Roller Bearings From China, 77 FR 50716... Act of 1930, as amended (``Act'').\\1\\ \\1\\ See Initiation of Five-Year (``Sunset'') Review, 76 FR 45778... Antidumping Duty Order, 76 FR 76143 (December 6, 2011). On July 31, 2012, the ITC determined, pursuant...

  18. 78 FR 38943 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-28

    ... Parts Thereof, Finished or Unfinished, From the People's Republic of China, 52 FR 22667 (June 15, 1987... Antidumping Duty Order, 62 FR 6189 (Feb. 11, 1997). Effective August 1, 2012, the majority shareholder of SGBC... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From...

  19. Preliminary list of the leaf-roller moths (Insecta: Lepidoptera: Tortricidae) of Virginia with comments on spatial and temporal distribution

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Based on the examination of 3,457 pinned specimens, we document 263 species of leaf-roller moths (Lepidoptera: Tortricidae) from the Commonwealth of Virginia. The vast majority of specimens examined are from five unrelated efforts: a survey of George Washington Memorial Parkway National Park, Fairfa...

  20. A powered roller/crimper for walk-behind tractors to terminate cover crops in conservation agriculture

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Roller/crimper implements have been used in large conservation farming systems to terminate cover crops near maturity and flatten them down to create a mulch through which cash crops can be planted directly into the cover residue. On small farms, tractors are usually small and less powerful relative...

  1. Silk gland gene expression during larval-pupal transitionin the cotton leaf roller Sylepta derogate (Lepidoptera: pyralidae)

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The cotton leaf roller, Sylepta derogata, is a silk-producing insect pest. While young larvae feed on the underside of leaves, the older ones roll cotton leaves and feed on the leaf edges, which defoliates cotton plants. The larvae produce silk to stabilize the rolled leaf and to balloon from used t...

  2. Corrective action plan for CAU No. 404: Roller Coaster Sewage Lagoons and North Disposal Trench, Tonopah Test Range

    SciTech Connect

    1997-07-01

    This Corrective Action Plan (CAP) provides the selected corrective action alternative and proposes the closure implementation methodology for the Roller Coaster Sewage Lagoons and North Disposal Trench Corrective Action Unit (CAU) No. 404. The site is located on the Tonopah Test Range. CAU 404 consists of two Corrective Action Sites (CAS): the Roller Coaster Lagoons (CAS No TA-03-001-TA-RC) and the North Disposal Trench (CAS No TA-21-001-TA-RC). A site map of the lagoons and trench is provided. The Roller Coaster Sewage Lagoons are comprised of two unlined lagoons that received liquid sanitary waste in 1963 from the Operation Roller Coaster Man Camp and debris from subsequent construction and range cleanup activities. The North Disposal Trench was excavated in approximately 1963 and received solid waste and debris from the man camp and subsequent construction and range cleanup activities. A small hydrocarbon spill occurred during the 1995 Voluntary Corrective Action (VCA) activities in an area associated with the North Disposal Trench CAS.

  3. 76 FR 76143 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-06

    ... Republic of China, 52 FR 22667 (June 15, 1987), as amended, Tapered Roller Bearings From the People's... Order in Accordance With Decision Upon Remand, 55 FR 6669 (Feb. 26, 1990) (``Order''). As a result of...'') Review, 76 FR 45778, 45779 (August 1, 2011) (``Sunset Initiation''). On August 16, 2011, the...

  4. Ultrahigh carbon steels, Damascus steels, and superplasticity

    SciTech Connect

    Sherby, O.D.; Wadsworth, J.

    1997-04-01

    The processing properties of ultrahigh carbon steels (UHCSs) have been studied at Stanford University over the past twenty years. These studies have shown that such steels (1 to 2.1% C) can be made superplastic at elevated temperature and can have remarkable mechanical properties at room temperature. It was the investigation of these UHCSs that eventually brought us to study the myths, magic, and metallurgy of ancient Damascus steels, which in fact, were also ultrahigh carbon steels. These steels were made in India as castings, known as wootz, possibly as far back as the time of Alexander the Great. The best swords are believed to have been forged in Persia from Indian wootz. This paper centers on recent work on superplastic UHCSs and on their relation to Damascus steels. 32 refs., 6 figs.

  5. Excellent durability of DLC film on carburized steel (JIS-SCr420) under a stress of 3.0 GPa

    NASA Astrophysics Data System (ADS)

    Yakabe, F.; Jinbo, Y.; Kumagai, M.; Horiuchi, T.; Kuwahara, H.; Ochiai, S.

    2008-03-01

    To improve durability of transmission gears, Diamond Like Carbon (DLC) film coated on roller was estimated as well as TiN film. These films were coated on JIS-SCr420 steel, which was carburized, quenched, and tempered. DLC and TiN films were deposited by PCVD and PVD process, respectively. These surface modified rollers were estimated by usual metallurgical methods (observation of microstructure by optical microscope, SEM, and TEM, measurement of hardness by Vickers hardness tester and nano-indentator), measurement of friction coefficient by ball-on-disk in dry atmosphere, analysis of carbon by Raman spectroscopy and hydrogen by EDRA, and lifetime of pitting by the roller-pitting test. The hardness values were 21 GPa and 26 GPa, the elasticity coefficients were 192 GPa and 336 GPa, the friction coefficients were 0.1~0.15 and 0.5~0.6 for DLC and TiN films, respectively. The present DLC was a typical DLC called as hydrogenated amorphous carbon (a-C: H). The hydrogen content was about 20 %. The surface fatigue resistance of DLC-coated specimen had 100 times longer life than that the carburized and quenched one even under Hertzian contact stress of 3.0 GPa. TiN coated specimen was failed at 3.0 GPa by 5.17·105 cycles despite that the strength of the surface of the substrate was reduced due to the exposure at higher temperature in the coating process than the temperature for tempering.

  6. Automated Identification and Evaluation of Subtechniques in Classical-Style Roller Skiing

    PubMed Central

    Sakurai, Yoshihisa; Fujita, Zenya; Ishige, Yusuke

    2014-01-01

    The aims of the present study were (1) the development of an automated system for identifying classical-style ski subtechniques using angular rate sensors, and (2) the determination of the relationships among skiing velocity, ski course conditions, and ski subtechniques using a global navigation satellite system (GNSS) and the developed automated identification system. In the first experiment, the performance of a male cross-country skier was used to develop an automated system for identifying classical-style ski subtechniques. In the second one, the performances of five male and five female college cross-country skiers were used to validate the developed identification system. Each subject wore inertial sensors on both wrists and both roller skis, a small video camera on the helmet, and a GNSS receiver. All subjects skied a 6,900-m roller ski course using the classical-style at their maximum speed. The adopted subtechniques were identified by the automated method based on the data obtained from the sensors, and also by visual count from a video recording of the same ski run. The results showed that the automated identification method could be definitively used to recognize various subtechniques. Specifically, the system correctly identified 9,307 subtechnique cycles out of a total of 9,444 counted visually, which indicated an accuracy of 98.5%. We also measured the skiing velocity and the course slope using the GNSS module. The data was then used to determine the subtechnique distributions as a function of the inclination and skiing velocity. It was observed that male and female skiers selected double poling below 6.7° and 5.5° uphill, respectively. In addition, male and female skiers selected diagonal stride above 0.7° and 2.5° uphill, and below 5.4 m/s and 4.5 m/s velocity, respectively. These results implied that the subtechnique distribution plot could be used to analyze the technical characteristics of each skier. Key Points The automatic identification

  7. Automated identification and evaluation of subtechniques in classical-style roller skiing.

    PubMed

    Sakurai, Yoshihisa; Fujita, Zenya; Ishige, Yusuke

    2014-09-01

    The aims of the present study were (1) the development of an automated system for identifying classical-style ski subtechniques using angular rate sensors, and (2) the determination of the relationships among skiing velocity, ski course conditions, and ski subtechniques using a global navigation satellite system (GNSS) and the developed automated identification system. In the first experiment, the performance of a male cross-country skier was used to develop an automated system for identifying classical-style ski subtechniques. In the second one, the performances of five male and five female college cross-country skiers were used to validate the developed identification system. Each subject wore inertial sensors on both wrists and both roller skis, a small video camera on the helmet, and a GNSS receiver. All subjects skied a 6,900-m roller ski course using the classical-style at their maximum speed. The adopted subtechniques were identified by the automated method based on the data obtained from the sensors, and also by visual count from a video recording of the same ski run. The results showed that the automated identification method could be definitively used to recognize various subtechniques. Specifically, the system correctly identified 9,307 subtechnique cycles out of a total of 9,444 counted visually, which indicated an accuracy of 98.5%. We also measured the skiing velocity and the course slope using the GNSS module. The data was then used to determine the subtechnique distributions as a function of the inclination and skiing velocity. It was observed that male and female skiers selected double poling below 6.7° and 5.5° uphill, respectively. In addition, male and female skiers selected diagonal stride above 0.7° and 2.5° uphill, and below 5.4 m/s and 4.5 m/s velocity, respectively. These results implied that the subtechnique distribution plot could be used to analyze the technical characteristics of each skier. Key PointsThe automatic identification

  8. Love at first fright: partner salience moderates roller-coaster-induced excitation transfer.

    PubMed

    Meston, Cindy M; Frohlich, Penny F

    2003-12-01

    This study examined the effects of residual nervous system arousal on perceptions of sexual attraction. Researchers approached individuals (males, n = 165; females, n = 135) at amusement parks as they were either waiting to begin or as they had just gotten off a roller-coaster ride. Participants were shown a photograph of an average attractive, opposite-gendered individual and asked to rate the individual on attractiveness and dating desirability. Participants were also asked to rate their seatmates' levels of attractiveness. Consistent with the predictions of excitation transfer theory, for males and females riding with a nonromantic partner, ratings of attractiveness and dating desirability toward the photographed individual were higher among persons exiting than entering the ride. Among persons riding with a romantic partner, there were no significant differences in attractiveness or dating desirability ratings between persons entering and exiting the ride. The findings are discussed in terms of the potential moderator effects of a salient romantic partner on excitation transfer. PMID:14574097

  9. The roller coaster flight strategy of bar-headed geese conserves energy during Himalayan migrations.

    PubMed

    Bishop, C M; Spivey, R J; Hawkes, L A; Batbayar, N; Chua, B; Frappell, P B; Milsom, W K; Natsagdorj, T; Newman, S H; Scott, G R; Takekawa, J Y; Wikelski, M; Butler, P J

    2015-01-16

    The physiological and biomechanical requirements of flight at high altitude have been the subject of much interest. Here, we uncover a steep relation between heart rate and wingbeat frequency (raised to the exponent 3.5) and estimated metabolic power and wingbeat frequency (exponent 7) of migratory bar-headed geese. Flight costs increase more rapidly than anticipated as air density declines, which overturns prevailing expectations that this species should maintain high-altitude flight when traversing the Himalayas. Instead, a "roller coaster" strategy, of tracking the underlying terrain and discarding large altitude gains only to recoup them later in the flight with occasional benefits from orographic lift, is shown to be energetically advantageous for flights over the Himalayas. PMID:25593180

  10. Performance tests with a 4.75 inch bore tapered-roller bearings at high speeds

    NASA Technical Reports Server (NTRS)

    Signer, H. R.; Pinel, S. I.

    1977-01-01

    The tapered-roller bearings were tested at speeds to 15,000 rpm which results in a cone-rib tangential velocity of 130 m/sec. (25,500 ft/min). Lubrication was applied either by jets or directly to the cone-rib, augmented with jets. Additional test parameters included thrust loads to 53,400 N (12,000 lbs), radial loads to 26,700 N (6,000 lbs), lubricant flow rates from 1.9 x 0.000 to 15.1 x 0.001 cubic meter/min. (0.5 to 4.0 gpm), and lubricant inlet temperatures of 350 K and 364 K (170 F and 195 F). Temperature distribution, separator speed, and drive-motor power demand were determined as functions of these test parameters.

  11. Is It More Thrilling to Ride at the Front or the Back of a Roller Coaster?

    NASA Astrophysics Data System (ADS)

    Alberghi, Stefano; Foschi, Alessandro; Pezzi, Giovanni; Ortolani, Fabio

    2007-12-01

    An activity called "Project Physics, a Classroom Without Walls" was started during the spring of 2003 at the amusement park in Mirabilandia (Italy). Many thousands of students from Italian middle and high schools are today participating in the initiative. Under the guidance of trained tutors, they perform physics experiments on some of the attractions at the park such as the roller coaster, the Ferris wheel, and the launch towers. The students involved in the experiments can enjoy learning how to observe reality through the eyes of a scientist and to apply classroom concepts to real situations. They discuss the sensations experienced on the rides, perform measurements with traditional and computer-interfaced instruments, analyze collected data, and discuss the results in an open-air physics laboratory. This paper describes the results of one such activity.

  12. Numerical simulation for double-roller rolling process with deep-cylinder ring

    NASA Astrophysics Data System (ADS)

    Dong-sheng, Qian; Jun, Guo; Lin, Hua

    2013-05-01

    Deep-cylinder rings, as the key mechanical parts of heavy energy equipment, have wide application in nuclear reaction pressure vessels, oil hydrogenation reactors and coal liquefaction devices. Double-roller rolling (DRR) is a new rotary plastic forming technology for deep-cylinder ring manufacturing, which has the advantageous of low energy and material consumption, high efficiency, good quality and large processing range, comparing to the conventional processing technology of free forging. In this paper, a numerical simulation investigation on DRR process of deep-cylinder ring is carried out based on ABAQUS FE software. A 3D coupled thermo-mechanical FE model is developed, the forming feasibility and basic deformation laws in the rolling process is analyzed. The results can provide a scientific guidance for the process design and optimization of the DRR with deep-cylinder ring.

  13. Edge coating apparatus with movable roller applicator for solar cell substrates

    SciTech Connect

    Pavani, Luca; Abas, Emmanuel

    2012-12-04

    A non-contact edge coating apparatus includes an applicator for applying a coating material on an edge of a solar cell substrate and a control system configured to drive the applicator. The control system may drive the applicator along an axis to maintain a distance with an edge of the substrate as the substrate is rotated to have the edge coated with a coating material. The applicator may include a recessed portion into which the edge of the substrate is received for edge coating. For example, the applicator may be a roller with a groove. Coating material may be introduced into the groove for application onto the edge of the substrate. A variety of coating materials may be employed with the apparatus including hot melt ink and UV curable plating resist.

  14. Roller coasters without differential equations—a Newtonian approach to constrained motion

    NASA Astrophysics Data System (ADS)

    Müller, Rainer

    2010-07-01

    Within the context of Newton's equation, we present a simple approach to the constrained motion of a body forced to move along a specified trajectory. Because the formalism uses a local frame of reference, it is simpler than other methods, making more complicated geometries accessible. No Lagrangian multipliers are necessary to determine the constraining forces. Although the method is able to deal with friction, it becomes particularly simple for conservative systems. We give an analytic expression for the constraining force for any two-dimensional frictionless trajectory that can be written in the form y = f(x). The approach is illustrated with examples from roller coaster physics, e.g. the camelback or the clothoid loop. It is possible to find analytic expressions for the constraining force in both cases.

  15. Hot roller embossing system equipped with a temperature margin-based controller

    SciTech Connect

    Kim, Seyoung Son, Youngsu; Lee, Sunghee; Ham, Sangyong; Kim, Byungin

    2014-08-15

    A temperature control system was proposed for hot roller embossing. The roll surface was heated using induction coils and cooled with a circulating chilled water system. The temperature of the roll surface was precisely controlled by a temperature margin-based control algorithm that we developed. Implementation of the control system reduced deviations in the roll surface temperature to less than ±2 °C. The tight temperature control and the ability to rapidly increase and decrease the roll temperature will allow optimum operating parameters to be developed quickly. The temperature margin-based controller could also be used to optimize the time course of electrical power and shorten the cooling time by choosing an appropriate temperature margin, possibly for limited power consumption. The chiller-equipped heating roll with the proposed control algorithm is expected to decrease the time needed to determine the optimal embossing process.

  16. The roller coaster flight strategy of bar-headed geese conserves energy during Himalayan migrations

    USGS Publications Warehouse

    Bishop, C.M.; Spivey, R.J.; Hawkes, L. A.; Batbayar, N.; Chua, B.; Frappell, P.B.; Milsom, W.K.; Natsagdorj, T.; Newman, S.H.; Scott, G.R.; Takekawa, John Y.; Wikelski, Martin; Butler, Patrick J.

    2015-01-01

    The physiological and biomechanical requirements of flight at high altitude have been the subject of much interest. Here, we uncover a steep relation between heart rate and wingbeat frequency (raised to the exponent 3.5) and estimated metabolic power and wingbeat frequency (exponent 7) of migratory bar-headed geese. Flight costs increase more rapidly than anticipated as air density declines, which overturns prevailing expectations that this species should maintain high-altitude flight when traversing the Himalayas. Instead, a "roller coaster" strategy, of tracking the underlying terrain and discarding large altitude gains only to recoup them later in the flight with occasional benefits from orographic lift, is shown to be energetically advantageous for flights over the Himalayas.

  17. Roller compaction: Effect of morphology and amorphous content of lactose powder on product quality.

    PubMed

    Omar, Chalak S; Dhenge, Ranjit M; Osborne, James D; Althaus, Tim O; Palzer, Stefan; Hounslow, Michael J; Salman, Agba D

    2015-12-30

    The effect of morphology and amorphous content, of three types of lactose, on the properties of ribbon produced using roller compaction was investigated. The three types of lactose powders were; anhydrous SuperTab21AN, α-lactose monohydrate 200 M, and spray dried lactose SuperTab11SD. The morphology of the primary particles was identified using scanning electron microscopy (SEM) and the powder amorphous content was quantified using NIR technique. SEM images showed that 21AN and SD are agglomerated type of lactose whereas the 200 M is a non-agglomerated type. During ribbon production, an online thermal imaging technique was used to monitor the surface temperature of the ribbon. It was found that the morphology and the amorphous content of lactose powders have significant effects on the roller compaction behaviour and on ribbon properties. The agglomerated types of lactose produced ribbon with higher surface temperature and tensile strength, larger fragment size, lower porosity and lesser fines percentages than the non-agglomerated type of lactose. The lactose powder with the highest amorphous content showed to result in a better binding ability between the primary particles. This type of lactose produced ribbons with the highest temperature and tensile strength, and the lowest porosity and amount of fines in the product. It also produced ribbon with more smooth surfaces in comparison to the other two types of lactose. It was noticed that there is a relationship between the surface temperature of the ribbon during production and the tensile strength of the ribbon; the higher the temperature of the ribbon during production the higher the tensile strength of the ribbon. PMID:26117279

  18. Disentangling migratory routes and wintering grounds of Iberian near-threatened European Rollers Coracias garrulus.

    PubMed

    Rodríguez-Ruiz, Juan; de la Puente, Javier; Parejo, Deseada; Valera, Francisco; Calero-Torralbo, Miguel A; Reyes-González, José M; Zajková, Zuzana; Bermejo, Ana; Avilés, Jesús M

    2014-01-01

    Long-distance migrants are suffering drastic declines in the last decades. Causes beneath this problem are complex due to the wide spatial and temporal scale involved. We aim to reveal migratory routes, stopover areas, wintering grounds, and migratory strategies for the most southwestern populations of the near-threatened European Roller Coracias garrulus in order to identify conservation key areas for the non-breeding stage of this species. To this end, we used tracking data from seven satellite transmitters fitted to birds breeding in different populations throughout the Iberian Peninsula and four geolocators fitted to individuals in a southeastern Iberian population. Precise satellite data were used to describe daily activity patterns and speed in relation to the main regions crossed during the migration. Individuals from the most southwestern Iberian populations made a detour towards the Atlantic African coast whereas those from northeastern populations followed a straight north-to-south route. We identified important stopover areas in the Sahel belt, mainly in the surroundings of the Lake Chad, and wintering grounds on southwestern Africa farther west than previously reported for the species. Concerning the migratory strategy, satellite data revealed: 1) a mainly nocturnal flying activity, 2) that migration speed depended on the type of crossed habitat, with higher average speed while crossing the desert; and 3) that the migration was slower and lasted longer in autumn than in spring. The studied populations showed weak migratory connectivity, suggesting the confluence of birds from a wide range of breeding grounds in a restricted wintering area. Therefore, we suggest to target on defining precisely key areas for this species and identifying specific threats in them in order to develop an appropriate global conservation programme for the European Roller.

  19. Effects of Occupational Tobacco Exposure on Foetal Growth, among Beedi Rollers in Coastal Karnataka

    PubMed Central

    Subba, Sonu H; Yamini

    2014-01-01

    Introduction: Though there is ample evidence on adverse effects of tobacco exposure caused by smoking during pregnancy on foetal outcomes, there is lack of studies done on the effects of exposure caused by transdermal absorption, as is seen among beedi rolling women. Therefore, this study was planned, to assess the effect of maternal exposure to tobacco, in the form of beedi-rolling, on the birth weight and other neonatal anthropometric measurements. Materials and Methods: A cross sectional study with controls was conducted, with 102 beedi rollers forming the study group and an equal number of matched controls (control group) (total 204). Data was collected by using a pre-tested questionnaire and anthropometric examinations of the neonates were carried out within 48 hours of their births. Results: Mean birth weight of the newborns was 2.66 (SD=0.32) among those who were born to beedi rolling women and it was 2.63 (SD=0.38) kg among the control group. Crown heel length was 48.09 centimeters (SD=1.93) in the study group and it was 48.12 cm (SD=1.92) in the control group. Beedi rolling beyond the 7th month of gestation and for more than six hours per day was associated with a small but insignificant decline in birth weight and crown heel length. Conclusion: Beedi-rolling was found to be relatively safe during pregnancy but it could produce adverse effects if it was continued into the third trimester and for longer durations. This study can make the beedi rollers as well as their employers aware of harmful over-exposure to beedi rolling and help them in preventing it. PMID:24995197

  20. Disentangling Migratory Routes and Wintering Grounds of Iberian Near-Threatened European Rollers Coracias garrulus

    PubMed Central

    Rodríguez-Ruiz, Juan; de la Puente, Javier; Parejo, Deseada; Valera, Francisco; Calero-Torralbo, Miguel A.; Reyes-González, José M.; Zajková, Zuzana; Bermejo, Ana; Avilés, Jesús M.

    2014-01-01

    Long-distance migrants are suffering drastic declines in the last decades. Causes beneath this problem are complex due to the wide spatial and temporal scale involved. We aim to reveal migratory routes, stopover areas, wintering grounds, and migratory strategies for the most southwestern populations of the near-threatened European Roller Coracias garrulus in order to identify conservation key areas for the non-breeding stage of this species. To this end, we used tracking data from seven satellite transmitters fitted to birds breeding in different populations throughout the Iberian Peninsula and four geolocators fitted to individuals in a southeastern Iberian population. Precise satellite data were used to describe daily activity patterns and speed in relation to the main regions crossed during the migration. Individuals from the most southwestern Iberian populations made a detour towards the Atlantic African coast whereas those from northeastern populations followed a straight north-to-south route. We identified important stopover areas in the Sahel belt, mainly in the surroundings of the Lake Chad, and wintering grounds on southwestern Africa farther west than previously reported for the species. Concerning the migratory strategy, satellite data revealed: 1) a mainly nocturnal flying activity, 2) that migration speed depended on the type of crossed habitat, with higher average speed while crossing the desert; and 3) that the migration was slower and lasted longer in autumn than in spring. The studied populations showed weak migratory connectivity, suggesting the confluence of birds from a wide range of breeding grounds in a restricted wintering area. Therefore, we suggest to target on defining precisely key areas for this species and identifying specific threats in them in order to develop an appropriate global conservation programme for the European Roller. PMID:25551212

  1. Roller compaction: Effect of morphology and amorphous content of lactose powder on product quality.

    PubMed

    Omar, Chalak S; Dhenge, Ranjit M; Osborne, James D; Althaus, Tim O; Palzer, Stefan; Hounslow, Michael J; Salman, Agba D

    2015-12-30

    The effect of morphology and amorphous content, of three types of lactose, on the properties of ribbon produced using roller compaction was investigated. The three types of lactose powders were; anhydrous SuperTab21AN, α-lactose monohydrate 200 M, and spray dried lactose SuperTab11SD. The morphology of the primary particles was identified using scanning electron microscopy (SEM) and the powder amorphous content was quantified using NIR technique. SEM images showed that 21AN and SD are agglomerated type of lactose whereas the 200 M is a non-agglomerated type. During ribbon production, an online thermal imaging technique was used to monitor the surface temperature of the ribbon. It was found that the morphology and the amorphous content of lactose powders have significant effects on the roller compaction behaviour and on ribbon properties. The agglomerated types of lactose produced ribbon with higher surface temperature and tensile strength, larger fragment size, lower porosity and lesser fines percentages than the non-agglomerated type of lactose. The lactose powder with the highest amorphous content showed to result in a better binding ability between the primary particles. This type of lactose produced ribbons with the highest temperature and tensile strength, and the lowest porosity and amount of fines in the product. It also produced ribbon with more smooth surfaces in comparison to the other two types of lactose. It was noticed that there is a relationship between the surface temperature of the ribbon during production and the tensile strength of the ribbon; the higher the temperature of the ribbon during production the higher the tensile strength of the ribbon.

  2. Kinematic and dynamic modeling and approximate analysis of a roller chain drive

    NASA Astrophysics Data System (ADS)

    Fuglede, Niels; Thomsen, Jon Juel

    2016-03-01

    A simple roller chain drive consisting of two sprockets connected by tight chain spans is investigated. First, a kinematic model is presented which include both spans and sprockets. An approach for calculating the chain wrapping length is presented, which also allows for the exact calculation of sprocket center positions for a given chain length. The kinematic analysis demonstrates that the total length of the chain wrapped around the sprockets generally varies during one tooth period. Analytical predictions for the wrapping length are compared to multibody simulation results and show very good agreement. It is thereby demonstrated that chain drives with tight chain spans must include compliant components to function. Second, a dynamic model is presented which includes the two spans and the driven sprocket. Assuming the presence of a stationary operating state, the presented dynamic model allows for analytical studies of the coupled motion of the chain spans and driven sprocket. Parametric excitation of the spans come from sprocket angular displacements, and the driven sprocket acts as a boundary which can be compliant in the axial direction. External transverse excitation of the spans comes from polygonal action, and is treated through kinematic forcing at the moving string boundaries. Perturbation analysis of the model is carried out using the method of multiple scales. Results show a multitude of internal and external resonance conditions, and some examples are presented of both decoupled and coupled motion. Together, the kinematic and dynamic model are aimed toward providing a framework for conducting and understanding both numerical, and experimental investigations of roller chain drive dynamics.

  3. Comminuting irradiated ferritic steel

    DOEpatents

    Bauer, Roger E.; Straalsund, Jerry L.; Chin, Bryan A.

    1985-01-01

    Disclosed is a method of comminuting irradiated ferritic steel by placing the steel in a solution of a compound selected from the group consisting of sulfamic acid, bisulfate, and mixtures thereof. The ferritic steel is used as cladding on nuclear fuel rods or other irradiated components.

  4. The steel scrap age.

    PubMed

    Pauliuk, Stefan; Milford, Rachel L; Müller, Daniel B; Allwood, Julian M

    2013-04-01

    Steel production accounts for 25% of industrial carbon emissions. Long-term forecasts of steel demand and scrap supply are needed to develop strategies for how the steel industry could respond to industrialization and urbanization in the developing world while simultaneously reducing its environmental impact, and in particular, its carbon footprint. We developed a dynamic stock model to estimate future final demand for steel and the available scrap for 10 world regions. Based on evidence from developed countries, we assumed that per capita in-use stocks will saturate eventually. We determined the response of the entire steel cycle to stock saturation, in particular the future split between primary and secondary steel production. During the 21st century, steel demand may peak in the developed world, China, the Middle East, Latin America, and India. As China completes its industrialization, global primary steel production may peak between 2020 and 2030 and decline thereafter. We developed a capacity model to show how extensive trade of finished steel could prolong the lifetime of the Chinese steelmaking assets. Secondary steel production will more than double by 2050, and it may surpass primary production between 2050 and 2060: the late 21st century can become the steel scrap age.

  5. The steel scrap age.

    PubMed

    Pauliuk, Stefan; Milford, Rachel L; Müller, Daniel B; Allwood, Julian M

    2013-04-01

    Steel production accounts for 25% of industrial carbon emissions. Long-term forecasts of steel demand and scrap supply are needed to develop strategies for how the steel industry could respond to industrialization and urbanization in the developing world while simultaneously reducing its environmental impact, and in particular, its carbon footprint. We developed a dynamic stock model to estimate future final demand for steel and the available scrap for 10 world regions. Based on evidence from developed countries, we assumed that per capita in-use stocks will saturate eventually. We determined the response of the entire steel cycle to stock saturation, in particular the future split between primary and secondary steel production. During the 21st century, steel demand may peak in the developed world, China, the Middle East, Latin America, and India. As China completes its industrialization, global primary steel production may peak between 2020 and 2030 and decline thereafter. We developed a capacity model to show how extensive trade of finished steel could prolong the lifetime of the Chinese steelmaking assets. Secondary steel production will more than double by 2050, and it may surpass primary production between 2050 and 2060: the late 21st century can become the steel scrap age. PMID:23442209

  6. Methods of forming steel

    DOEpatents

    Branagan, Daniel J.; Burch, Joseph V.

    2001-01-01

    In one aspect, the invention encompasses a method of forming a steel. A metallic glass is formed and at least a portion of the glass is converted to a crystalline steel material having a nanocrystalline scale grain size. In another aspect, the invention encompasses another method of forming a steel. A molten alloy is formed and cooled the alloy at a rate which forms a metallic glass. The metallic glass is devitrified to convert the glass to a crystalline steel material having a nanocrystalline scale grain size. In yet another aspect, the invention encompasses another method of forming a steel. A first metallic glass steel substrate is provided, and a molten alloy is formed over the first metallic glass steel substrate to heat and devitrify at least some of the underlying metallic glass of the substrate.

  7. Visualization and prediction of porosity in roller compacted ribbons with near-infrared chemical imaging (NIR-CI).

    PubMed

    Khorasani, M; Amigo, J M; Sonnergaard, J; Olsen, P; Bertelsen, P; Rantanen, J

    2015-05-10

    The porosity of roller compacted ribbon is recognized as an important critical quality attribute which has a huge impact on the final product quality. The purpose of this study was to investigate the use of near-infrared chemical imaging (NIR-CI) for porosity estimation of ribbons produced at different roll pressures. Two off-line methods were utilized as reference methods. The relatively fast method (oil absorption) was comparable with the more time-consuming mercury intrusion method (R(2)=0.98). Therefore, the oil method was selected as the reference off line method. It was confirmed by both reference methods that ribbons compressed at a higher pressure resulted in a lower mean porosity. Using NIR-CI in combination with multivariate data analysis it was possible to visualize and predict the porosity distribution of the ribbons. This approach is considered important for process monitoring and control of continuously operating roller compaction line. PMID:25746502

  8. The use of fluvial and marine sediments in the formulation of roller compacted concrete for use in pavements.

    PubMed

    Zdiri, M; Abriakb, N E; Ben Ouezdoua, M; Neji, J

    2009-07-01

    In the manufacture of Roller Compacted Concrete (RCC) used for pavement materials, various types of aggregates are used, such as crushed and rolled limestone or siliceous aggregates. The main objective is always to reach the maximum compactness to achieve higher mechanical performances. In the present work, fluvial and marine sediments, resulting from the dredging of harbours and rivers, were introduced as aggregates in the preparation of RCC for pavement construction, with a view to improving the mechanical strength of the RCC. This study included a granulometric, mineralogical and chemical characterization of the aggregates. The work also contains a mechanical characterization of the resulting material. The objective of the study was to find a resistant RCC, by developing materials such as sediments that are often classified as a waste and where their storage is harmful to the environment. The mechanical strengths obtained showed the profitability of using a Roller Compacted Concrete containing sediments.

  9. Spherical roller bearing analysis. SKF computer program SPHERBEAN. Volume 3: Program correlation with full scale hardware tests

    NASA Technical Reports Server (NTRS)

    Kleckner, R. J.; Rosenlieb, J. W.; Dyba, G.

    1980-01-01

    The results of a series of full scale hardware tests comparing predictions of the SPHERBEAN computer program with measured data are presented. The SPHERBEAN program predicts the thermomechanical performance characteristics of high speed lubricated double row spherical roller bearings. The degree of correlation between performance predicted by SPHERBEAN and measured data is demonstrated. Experimental and calculated performance data is compared over a range in speed up to 19,400 rpm (0.8 MDN) under pure radial, pure axial, and combined loads.

  10. Model Investigations on the Stability of the Steel-Slag Interface in Continuous-Casting Process

    NASA Astrophysics Data System (ADS)

    Hagemann, René; Schwarze, Rüdiger; Heller, Hans P.; Scheller, Piotr R.

    2013-02-01

    In the continuous-casting mold, the mold powder in contact with the liquid steel surface forms a liquid slag layer. The flow along the steel-slag interface generates shear stress at the interface, waves, and leads to fingerlike protrusions of liquid slag into steel. Reaching a critical flow velocity and thereby shear stress, the protrusions can disintegrate into slag droplets following the flow in the liquid steel pool. These entrained droplets can form finally nonmetallic inclusions in steel material, cause defects in the final product, and therefore, should be avoided. In the current work, the stability of a liquid-liquid interface without mass transfer between phases was investigated in cold model study using a single-roller driven flow in oil-water systems with various oil properties. Applying the similarity theory, two dimensionless numbers were identified, viz. capillary number Ca and the ratio of kinematic viscosities ν 1/ ν 2, which are suitable to describe the force balance for the problem treated. The critical values of the dimensionless capillary number Ca* marking the start of lighter phase entrainment into the heavier fluid, are determined over a wide range of fluid properties. The dimensionless number ν 1/ ν 2 was defined as the ratio of kinematic viscosities of the lighter phase ν 1 and heavier phase ν 2. The ratios of kinematic viscosities of different steel-slag systems were calculated using measured thermophysical properties. With the knowledge of thermophysical properties of steel-slag systems, Ca* for slag entrainment as a function of v 1/ v 2 is derived. Assuming no reaction between the phases and no interfacial flow, slag entrainment should not occur under the usual casting conditions.

  11. ROLLER COASTER RETINOPATHY: CASE REPORT OF SYMPTOMATIC BILATERAL INTRARETINAL HEMORRHAGES AFTER SHAKING INJURY IN AN OTHERWISE HEALTHY ADULT

    PubMed Central

    Patel, Yogin P.; Saraf, Steven S.; Desai, Uday R.

    2016-01-01

    Purpose: Traumatic head injuries not involving the eye have been known to cause retinal injury through multiple mechanisms. Abusive head trauma remains the prototypical example. We propose to demonstrate the first case of bilateral multiple retinal hemorrhages in a young healthy adult related to riding multiple theme park roller coasters. Methods: The patient was evaluated with a complete ophthalmic examination including dilated extended ophthalmoscopy, fluorescein angiography, optical coherence tomography, and fundus photography. Results: The patient was found to have a bilateral symptomatic macular retinopathy characterized by multiple intraretinal hemorrhages. Given the lack of other systemic findings and negative medical workup, her signs and symptoms were thought to be attributed to the same day attendance of a theme park and riding of multiple roller coasters. Conclusion: Theme park roller coasters, as well as other attractions, may affect the eye at the vitreoretinal interface. This type of acceleration–deceleration injury should be considered in the differential of an adolescent or adult patient with retinal hemorrhage in the absence of other pathologic processes to explain clinical findings. PMID:26630245

  12. An Analysis of US Emergency Department Visits From Falls From Skiing, Snowboarding, Skateboarding, Roller-Skating, and Using Nonmotorized Scooters.

    PubMed

    Nathanson, Brian H; Ribeiro, Kara; Henneman, Philip L

    2016-07-01

    We analyzed the US incidence of emergency department (ED) visits and hospitalizations for falls from skiing, snowboarding, skateboarding, roller-skating, and nonmotorized scooters in 2011. The outcome was hospital admission from the ED. The primary analysis compared pediatric patients aged 1 to 17 years to adults aged 18 to 44 years. The analysis used ICD-9 E-codes E885.0 to E885.4 using discharge data from the Nationwide Emergency Department Sample, Healthcare Cost and Utilization Project, Agency for Healthcare Research and Quality. Approximately 214 000 ED visits met study criteria. Skiing injuries had the highest percentage of hospitalizations (3.30% in pediatric patients and 6.65% in adults 18-44 years old). Skateboard and snowboard injuries were more likely to require hospitalization than roller skating injuries in pediatric patients (odds ratio = 2.42; 95% CI = 2.14-2.75 and odds ratio = 1.83; 95% CI =1.55-2.15, respectively). In contrast, skateboard and snowboard injuries were less severe than roller-skating injuries in adults.

  13. Isocyanate Exposure Below Analytical Detection When a Paint Brush and Roller Are Used to Apply Moisture-Cure Polyurethane Paint.

    PubMed

    Reeb-Whitaker, Carolyn K; Schoonover, Todd M

    2016-05-01

    Isocyanate exposure is known to be hazardous when polyurethane paints are applied with a spray gun, but less is known of exposure when paint is applied with a paint brush and roller. Concentrations of 1,6-hexamethylene diisocyanate (HDI) monomer and three HDI polymers were assessed when two moisture-cure polyurethane paints containing 31-35% isocyanates were applied with a paint roller and brush. Short-term 15-min samples were taken during paint application in an indoor test environment with no ventilation (n= 12); in an outdoor test environment (n= 11); and in an outdoor in-situ assessment (n= 22). The outdoor in-situ assessment involved the painting of a bus shelter and light poles at a public transit station over two night shifts. All isocyanate samples were below analytical detection. The analytical limits of detection for HDI monomer, HDI biuret, HDI isocyanurate, and HDI uretdione were 0.005, 0.84, 0.87, and 0.88 µg, respectively. The finding that isocyanate concentrations were below detection is attributed to the use of paint roller and brush which minimize paint aerosolization and the paint formulation itself which contained <1% of volatile HDI monomer.

  14. Isocyanate Exposure Below Analytical Detection When a Paint Brush and Roller Are Used to Apply Moisture-Cure Polyurethane Paint.

    PubMed

    Reeb-Whitaker, Carolyn K; Schoonover, Todd M

    2016-05-01

    Isocyanate exposure is known to be hazardous when polyurethane paints are applied with a spray gun, but less is known of exposure when paint is applied with a paint brush and roller. Concentrations of 1,6-hexamethylene diisocyanate (HDI) monomer and three HDI polymers were assessed when two moisture-cure polyurethane paints containing 31-35% isocyanates were applied with a paint roller and brush. Short-term 15-min samples were taken during paint application in an indoor test environment with no ventilation (n= 12); in an outdoor test environment (n= 11); and in an outdoor in-situ assessment (n= 22). The outdoor in-situ assessment involved the painting of a bus shelter and light poles at a public transit station over two night shifts. All isocyanate samples were below analytical detection. The analytical limits of detection for HDI monomer, HDI biuret, HDI isocyanurate, and HDI uretdione were 0.005, 0.84, 0.87, and 0.88 µg, respectively. The finding that isocyanate concentrations were below detection is attributed to the use of paint roller and brush which minimize paint aerosolization and the paint formulation itself which contained <1% of volatile HDI monomer. PMID:26833099

  15. Instrumented roll technology for the design space development of roller compaction process.

    PubMed

    Nesarikar, Vishwas V; Vatsaraj, Nipa; Patel, Chandrakant; Early, William; Pandey, Preetanshu; Sprockel, Omar; Gao, Zhihui; Jerzewski, Robert; Miller, Ronald; Levin, Michael

    2012-04-15

    Instrumented roll technology on Alexanderwerk WP120 roller compactor was developed and utilized successfully for the measurement of normal stress on ribbon during the process. The effects of process parameters such as roll speed (4-12 rpm), feed screw speed (19-53 rpm), and hydraulic roll pressure (40-70 bar) on normal stress and ribbon density were studied using placebo and active pre-blends. The placebo blend consisted of 1:1 ratio of microcrystalline cellulose PH102 and anhydrous lactose with sodium croscarmellose, colloidal silicon dioxide, and magnesium stearate. The active pre-blends were prepared using various combinations of one active ingredient (3-17%, w/w) and lubricant (0.1-0.9%, w/w) levels with remaining excipients same as placebo. Three force transducers (load cells) were installed linearly along the width of the roll, equidistant from each other with one transducer located in the center. Normal stress values recorded by side sensors and were lower than normal stress values recorded by middle sensor and showed greater variability than middle sensor. Normal stress was found to be directly proportional to hydraulic pressure and inversely to screw to roll speed ratio. For active pre-blends, normal stress was also a function of compressibility. For placebo pre-blends, ribbon density increased as normal stress increased. For active pre-blends, in addition to normal stress, ribbon density was also a function of gap. Models developed using placebo were found to predict ribbon densities of active blends with good accuracy and the prediction error decreased as the drug concentration of active blend decreased. Effective angle of internal friction and compressibility properties of active pre blend may be used as key indicators for predicting ribbon densities of active blend using placebo ribbon density model. Feasibility of on-line prediction of ribbon density during roller compaction was demonstrated using porosity-pressure data of pre-blend and normal stress

  16. Instrumented roll technology for the design space development of roller compaction process.

    PubMed

    Nesarikar, Vishwas V; Vatsaraj, Nipa; Patel, Chandrakant; Early, William; Pandey, Preetanshu; Sprockel, Omar; Gao, Zhihui; Jerzewski, Robert; Miller, Ronald; Levin, Michael

    2012-04-15

    Instrumented roll technology on Alexanderwerk WP120 roller compactor was developed and utilized successfully for the measurement of normal stress on ribbon during the process. The effects of process parameters such as roll speed (4-12 rpm), feed screw speed (19-53 rpm), and hydraulic roll pressure (40-70 bar) on normal stress and ribbon density were studied using placebo and active pre-blends. The placebo blend consisted of 1:1 ratio of microcrystalline cellulose PH102 and anhydrous lactose with sodium croscarmellose, colloidal silicon dioxide, and magnesium stearate. The active pre-blends were prepared using various combinations of one active ingredient (3-17%, w/w) and lubricant (0.1-0.9%, w/w) levels with remaining excipients same as placebo. Three force transducers (load cells) were installed linearly along the width of the roll, equidistant from each other with one transducer located in the center. Normal stress values recorded by side sensors and were lower than normal stress values recorded by middle sensor and showed greater variability than middle sensor. Normal stress was found to be directly proportional to hydraulic pressure and inversely to screw to roll speed ratio. For active pre-blends, normal stress was also a function of compressibility. For placebo pre-blends, ribbon density increased as normal stress increased. For active pre-blends, in addition to normal stress, ribbon density was also a function of gap. Models developed using placebo were found to predict ribbon densities of active blends with good accuracy and the prediction error decreased as the drug concentration of active blend decreased. Effective angle of internal friction and compressibility properties of active pre blend may be used as key indicators for predicting ribbon densities of active blend using placebo ribbon density model. Feasibility of on-line prediction of ribbon density during roller compaction was demonstrated using porosity-pressure data of pre-blend and normal stress

  17. Evaluation of HL-20 roller pump and Rotaflow centrifugal pump on perfusion quality and gaseous microemboli delivery.

    PubMed

    Yee, Stella; Qiu, Feng; Su, Xiaowei; Rider, Alan; Kunselman, Allen R; Guan, Yulong; Undar, Akif

    2010-11-01

    The purpose of this study was to compare the HL-20 roller pump (Jostra USA, Austin, TX, USA) and Rotaflow centrifugal pump (Jostra USA) on hemodynamic energy production and gaseous microemboli (GME) delivery in a simulated neonatal cardiopulmonary bypass (CPB) circuit under nonpulsatile perfusion. This study employed a simulated model of the pediatric CPB including a Jostra HL-20 heart-lung machine (or a Rotaflow centrifugal pump), a Capiox BabyRX05 oxygenator (Terumo Corporation, Tokyo, Japan), a Capiox pediatric arterial filter (Terumo Corporation), and ¼-inch tubing. The total volume of the experimental system was 700mL (500mL for the circuit and 200mL for the pseudo neonatal patient). The hematocrit was maintained at 30% using human blood. At the beginning of each trial, a 5mL bolus of air was injected into the venous line. Both GME data and pressure values were recorded at postpump and postoxygenator sites. All the experiments were conducted under nonpulsatile perfusion at three flow rates (500, 750, and 1000mL/min) and three blood temperatures (35, 30, and 25°C). As n=6 for each setup, a total of 108 trials were done. The total number of GME increased as temperature decreased from 35°C to 25°C in the trials using the HL-20 roller pump while the opposite effect occurred when using the Rotaflow centrifugal pump. At a given temperature, total GME counts increased with increasing flow rates for both pumps. Results indicated the Rotaflow centrifugal pump delivered significantly fewer microemboli compared to the HL-20 roller pump, especially under high flow rates. Less than 10% of total microemboli were larger than 40µm in size and the majority of GME were in the 0-20µm class in all trials. Postpump total hemodynamic energy (THE) increased with increasing flow rates and decreasing temperatures in both circuits using these two pumps. The HL-20 roller pump delivered more THE than the Rotaflow centrifugal pump at all tested flow rates and temperature conditions

  18. Roller Testing to Mimic Damage of the ISS SARJ Ring and Durability Test to Simulate Fifteen Years of SARJ Operation Using the Damaged Surface

    NASA Technical Reports Server (NTRS)

    Krantz, Timothy L.; Elchert, Justin P.; DellaCorte, Christopher; Dube, Michael J.

    2016-01-01

    The International Space Station's starboard Solar Alpha Rotary Joint (SARJ) experienced a breakdown of the joint's race ring surface. The starboard SARJ mechanism was cleaned and lubricated with grease. To provide some guidance on the expected behavior of the damaged SARJ ring with continued operations, experiments were conducted using rollers and a vacuum roller test rig. The approach of the experimental work involved three main steps: (1) initiate damage using conditions representative of the SARJ with inadequate lubrication; (2) propagate the damage by operating the test rollers without lubrication; and (3) assess the durability of the roller by testing to simulate the equivalent of 15 years of SARJ operation on the damaged surface assuming adequate grease lubrication. During the rig testing, additional and/or replacement grease was introduced at regular intervals to maintain good lubrication in the rig. The damage to the nitride layer continued even after application of grease. The grease lubrication proved to be effective for limiting the value of the axial force that can be developed. Limiting the axial force on the SARJ mechanism is important since the larger the axial force the more concentrated the load pressure becomes on the blend-radius location on the SARJ roller. After the testing simulating 15 years of SARJ operations, the wear depths were the order of 0.2 mm for the nitrided 15-5 roller and the order of 0.06 mm for the mating 440C roller. Metallographic inspections were done to search for indications of impending fatigue or other fracture indications that might eventually propagate and cause structural failure. There were no indications or features found that could eventually compromise structural integrity.

  19. Conductor load bearing roller for a gas-insulated transmission line having a corrugated outer conductor

    DOEpatents

    Fischer, William H.; Yoon, Kue H.

    1984-04-10

    A gas-insulated transmission line includes a corrugated outer conductor, an inner conductor disposed within and insulated from the outer conductor by means of support insulators and an insulating gas, and a transport device for supporting and permitting movement of the inner conductor/insulating support assembly axially along the corrugated outer conductor without radial displacement. The transport device includes two movable contacts, such as skids or rollers, supported on a common pivot lever, the pivot lever being rotatably disposed about a pivot lever axis, which pivot lever axis is in turn disposed on the periphery of a support insulator or particle trap if one is used. The movable contacts are separated axially a distance equal to the axial distance between the peaks and valleys of the corrugations of the outer conductor and separated radially a distance equal to the radial distance between the peaks and valleys of the corrugations of the outer conductor. The transport device has the pivot lever axis disposed perpendicular to the direction of travel of the inner conductor/insulating support assembly.

  20. Roller Coaster Scanning reveals spontaneous triggering of dendritic spikes in CA1 interneurons.

    PubMed

    Katona, Gergely; Kaszás, Attila; Turi, Gergely F; Hájos, Norbert; Tamás, Gábor; Vizi, E Sylvester; Rózsa, Balázs

    2011-02-01

    Inhibitory interneurons are considered to be the controlling units of neural networks, despite their sparse number and unique morphological characteristics compared with excitatory pyramidal cells. Although pyramidal cell dendrites have been shown to display local regenerative events--dendritic spikes (dSpikes)--evoked by artificially patterned stimulation of synaptic inputs, no such studies exist for interneurons or for spontaneous events. In addition, imaging techniques have yet to attain the required spatial and temporal resolution for the detection of spontaneously occurring events that trigger dSpikes. Here we describe a high-resolution 3D two-photon laser scanning method (Roller Coaster Scanning) capable of imaging long dendritic segments resolving individual spines and inputs with a temporal resolution of a few milliseconds. By using this technique, we found that local, NMDA receptor-dependent dSpikes can be observed in hippocampal CA1 stratum radiatum interneurons during spontaneous network activities in vitro. These NMDA spikes appear when approximately 10 spatially clustered inputs arrive synchronously and trigger supralinear integration in dynamic interaction zones. In contrast to the one-to-one relationship between computational subunits and dendritic branches described in pyramidal cells, here we show that interneurons have relatively small (∼14 μm) sliding interaction zones. Our data suggest a unique principle as to how interneurons integrate synaptic information by local dSpikes. PMID:21224413

  1. Biocompatible enzymatic roller pens for direct writing of biocatalytic materials: "do-it-yourself" electrochemical biosensors.

    PubMed

    Bandodkar, Amay J; Jia, Wenzhao; Ramírez, Julian; Wang, Joseph

    2015-06-01

    The development of enzymatic-ink-based roller pens for direct drawing of biocatalytic sensors, in general, and for realizing renewable glucose sensor strips, in particular, is described. The resulting enzymatic-ink pen allows facile fabrication of high-quality inexpensive electrochemical biosensors of any design by the user on a wide variety of surfaces having complex textures with minimal user training. Unlike prefabricated sensors, this approach empowers the end user with the ability of "on-demand" and "on-site" designing and fabricating of biocatalytic sensors to suit their specific requirement. The resulting devices are thus referred to as "do-it-yourself" sensors. The bio-active pens produce highly reproducible biocatalytic traces with minimal edge roughness. The composition of the new enzymatic inks has been optimized for ensuring good biocatalytic activity, electrical conductivity, biocompati-bility, reproducible writing, and surface adherence. The resulting inks are characterized using spectroscopic, viscometric, electrochemical, thermal and microscopic techniques. Applicability to renewable blood glucose testing, epidermal glucose monitoring, and on-leaf phenol detection are demonstrated in connection to glucose oxidase and tyrosinase-based carbon inks. The "do-it-yourself" renewable glucose sensor strips offer a "fresh," reproducible, low-cost biocatalytic sensor surface for each blood test. The ability to directly draw biocatalytic conducting traces even on unconventional surfaces opens up new avenues in various sensing applications in low-resource settings and holds great promise for diverse healthcare, environmental, and defense domains. PMID:25721554

  2. Application of statistics filter method and clustering analysis in fault diagnosis of roller bearings

    NASA Astrophysics Data System (ADS)

    Song, L. Y.; Wang, H. Q.; Gao, J. J.; Yang, J. F.; Liu, W. B.; Chen, P.

    2012-05-01

    Condition diagnosis of roller bearings depends largely on the feature analysis of vibration signals. Spectrum statistics filter (SSF) method could adaptively reduce the noise. This method is based on hypothesis testing in the frequency domain to eliminate the identical component between the reference signal and the primary signal. This paper presents a statistical parameter namely similarity factor to evaluate the filtering performance. The performance of the method is compared with the classical method, band pass filter (BPF). Results show that statistics filter is preferable to BPF in vibration signal processing. Moreover, the significance level awould be optimized by genetic algorithms. However, it is very difficult to identify fault states only from time domain waveform or frequency spectrum when the effect of the noise is so strong or fault feature is not obvious. Pattern recognition is then applied to fault diagnosis in this study through system clustering method. This paper processes experiment rig data that after statistics filter, and the accuracy of clustering analysis increases substantially.

  3. Maximum margin classification based on flexible convex hulls for fault diagnosis of roller bearings

    NASA Astrophysics Data System (ADS)

    Zeng, Ming; Yang, Yu; Zheng, Jinde; Cheng, Junsheng

    2016-01-01

    A maximum margin classification based on flexible convex hulls (MMC-FCH) is proposed and applied to fault diagnosis of roller bearings. In this method, the class region of each sample set is approximated by a flexible convex hull of its training samples, and then an optimal separating hyper-plane that maximizes the geometric margin between flexible convex hulls is constructed by solving a closest pair of points problem. By using the kernel trick, MMC-FCH can be extended to nonlinear cases. In addition, multi-class classification problems can be processed by constructing binary pairwise classifiers as in support vector machine (SVM). Actually, the classical SVM also can be regarded as a maximum margin classification based on convex hulls (MMC-CH), which approximates each class region with a convex hull. The convex hull is a special case of the flexible convex hull. To train a MMC-FCH classifier, time-domain and frequency-domain statistical parameters are extracted not only from raw vibration signals but also from the resulting intrinsic mode functions (IMFs) by performing empirical mode decomposition (EMD) on the raw signals, and then the distance evaluation technique (DET) is used to select salient features from the whole statistical features. The experiments on bearing datasets show that the proposed method can reliably recognize different bearing faults.

  4. Determination of the Nip Angle in Roller Compactors With Serrated Rolls.

    PubMed

    Tan, Bernice Mei Jin; Chan, Lai Wah; Heng, Paul Wan Sia

    2016-06-01

    In roller compaction, the nip angle defines the critical transition interface between the slip and nip regions which is used to model material densification behavior and the properties of compacted ribbons. Current methods to determine the nip angle require either sophisticated instrumentation on smooth rolls or input parameters that are difficult to obtain experimentally. In this study, a practical method to determine nip angles for serrated rolls was developed based on mass balance considerations established around the nip region. Experimental input relating to roll geometry, powder density, and mass output from the compactor were required and they could be obtained reliably. The calculated nip angles were validated against those obtained from physical measurements during actual roll compaction. These nip angles were in agreement for various powder formulations containing plastic and brittle materials. The nip angles ranged from 4° to 12° and decreased significantly when the proportion of brittle material increased. Nip angles were also calculated using the widely used Johanson model. However, wall friction measurement on serrated roll surfaces could be impractical. The Johanson model-derived nip angles could differ by 3°-8° just by altering the roughness of the reference wall and this had compromised their reliability. PMID:27238494

  5. Biocompatible enzymatic roller pens for direct writing of biocatalytic materials: "do-it-yourself" electrochemical biosensors.

    PubMed

    Bandodkar, Amay J; Jia, Wenzhao; Ramírez, Julian; Wang, Joseph

    2015-06-01

    The development of enzymatic-ink-based roller pens for direct drawing of biocatalytic sensors, in general, and for realizing renewable glucose sensor strips, in particular, is described. The resulting enzymatic-ink pen allows facile fabrication of high-quality inexpensive electrochemical biosensors of any design by the user on a wide variety of surfaces having complex textures with minimal user training. Unlike prefabricated sensors, this approach empowers the end user with the ability of "on-demand" and "on-site" designing and fabricating of biocatalytic sensors to suit their specific requirement. The resulting devices are thus referred to as "do-it-yourself" sensors. The bio-active pens produce highly reproducible biocatalytic traces with minimal edge roughness. The composition of the new enzymatic inks has been optimized for ensuring good biocatalytic activity, electrical conductivity, biocompati-bility, reproducible writing, and surface adherence. The resulting inks are characterized using spectroscopic, viscometric, electrochemical, thermal and microscopic techniques. Applicability to renewable blood glucose testing, epidermal glucose monitoring, and on-leaf phenol detection are demonstrated in connection to glucose oxidase and tyrosinase-based carbon inks. The "do-it-yourself" renewable glucose sensor strips offer a "fresh," reproducible, low-cost biocatalytic sensor surface for each blood test. The ability to directly draw biocatalytic conducting traces even on unconventional surfaces opens up new avenues in various sensing applications in low-resource settings and holds great promise for diverse healthcare, environmental, and defense domains.

  6. Latest experiences and developments of coal grinding plants with roller grinding mills

    SciTech Connect

    Salewski, G.

    1996-12-31

    LOESCHE GmbH has for decades been involved in the research and development of coal processing plants with roller grinding mills. By intensive research work the engineers and technicians at LOESCHE GmbH, Duesseldorf, have successfully provided new coal processing technologies for the varied needs of industry. One of the first PCI Plants in Europe was equipped in 1985 by LOESCHE with two central coal grinding plants for the ironmaking plant at Dillingen, Germany. These two plants use hot stove waste gas in conjunction with blast furnace gas fired in a hot gas generator, as a heat source for coal drying. Further plant configurations have been developed and put into operation. Experience with self-inerted grinding plants (i.e., plants that do not make use of hot and dry waste gases) has been gained for various applications, such as coal gasification, liquefaction and pulverized coal injection into blast furnaces. In this paper experience and development of self-inerted, foreign-inerted and air-operated plants will be discussed.

  7. Pediatric ECMO outcomes: comparison of centrifugal versus roller blood pumps using propensity score matching.

    PubMed

    Barrett, Cindy S; Jaggers, James J; Cook, E Francis; Graham, Dionne A; Yarlagadda, Vasmi V; Teele, Sarah A; Almond, Christopher S; Bratton, Susan L; Seeger, John D; Dalton, Heidi J; Rycus, Peter T; Laussen, Peter C; Thiagarajan, Ravi R

    2013-01-01

    Centrifugal blood pumps are being increasingly utilized in children supported with extracorporeal membrane oxygenation (ECMO). Our aim was to determine if survival and ECMO-related morbidities in children supported with venoarterial (VA) ECMO differed by blood pump type.Children aged less than 18 years who underwent VA ECMO support from 2007 to 2009 and reported to the Extracorporeal Life Support Organization registry were propensity score matched (Greedy 1:1 matching) using pre-ECMO characteristics.A total of 2,656 (centrifugal = 2,231, roller = 425) patients were identified and 548 patients (274 per pump type) were included in the propensity score-matched cohort. Children supported with centrifugal pumps had increased odds of hemolysis (odds ratio [OR], 4.03 95% confidence interval [CI], 2.37-6.87), hyperbilirubinemia (OR, 5.48; 95% CI, 2.62-11.49), need for inotropic support during ECMO (OR, 1.54; 95% CI, 1.09-2.17), metabolic alkalosis (blood pH > 7.6) during ECMO (OR, 3.13; 95% CI, 1.49-6.54), and acute renal failure (OR, 1.61; 95% CI, 1.10-2.39). Survival to hospital discharge did not differ by pump type.In a propensity score-matched cohort of pediatric ECMO patients, children supported with centrifugal pumps had increased odds of ECMO-related complications. There was no difference in survival between groups.

  8. Field drilling tests on improved geothermal unsealed roller-cone bits. Final report

    SciTech Connect

    Hendrickson, R.R.; Jones, A.H.; Winzenried, R.W.; Maish, A.B.

    1980-05-01

    The development and field testing of a 222 mm (8-3/4 inch) unsealed, insert type, medium hard formation, high-temperature bit are described. Increased performance was gained by substituting improved materials in critical bit components. These materials were selected on bases of their high temperature properties, machinability and heat treatment response. Program objectives required that both machining and heat treating could be accomplished with existing rock bit production equipment. Six of the experimental bits were subjected to air drilling at 240/sup 0/C (460/sup 0/F) in Franciscan graywacke at the Geysers (California). Performances compared directly to conventional bits indicate that in-gage drilling time was increased by 70%. All bits at the Geysers are subjected to reaming out-of-gage hole prior to drilling. Under these conditions the experimental bits showed a 30% increase in usable hole drilled, compared with the conventional bits. The materials selected improved roller wear by 200%, friction per wear by 150%, and lug wear by 150%. These tests indicate a potential well cost savings of 4 to 8%. Savings of 12% are considered possible with drilling procedures optimized for the experimental bits.

  9. Modern Steel Framed Schools.

    ERIC Educational Resources Information Center

    American Inst. of Steel Construction, Inc., New York, NY.

    In view of the cost of structural framing for school buildings, ten steel-framed schools are examined to review the economical advantages of steel for school construction. These schools do not resemble each other in size, shape, arrangement or unit cost; some are original in concept and architecture, and others are conservative. Cost and…

  10. Steel Industry Wastes.

    ERIC Educational Resources Information Center

    Schmidtke, N. W.; Averill, D. W.

    1978-01-01

    Presents a literature review of wastes from steel industry, covering publications of 1976-77. This review covers: (1) coke production; (2) iron and steel production; (3) rolling operations; and (4) surface treatment. A list of 133 references is also presented. (NM)

  11. The Steel Band.

    ERIC Educational Resources Information Center

    Weil, Bruce

    1996-01-01

    Describes studying the steel drum, an import from Trinidad, as an instrument of intellectual growth. Describes how developing a steel drum band provided Montessori middle school students the opportunity to experience some important feelings necessary to emotional growth during this difficult age: competence, usefulness, independence, and…

  12. Comparison of the centrifugal and roller pump in elective coronary artery bypass surgery--a prospective, randomized study with special emphasis upon platelet activation.

    PubMed

    Andersen, Knut S; Nygreen, Else L; Grong, Ketil; Leirvaag, Beryl; Holmsen, Holm

    2003-12-01

    Objective--Evaluation of the centrifugal pump vs roller pump concerning effects upon platelet function, hemolysis and clinical outcome in elective coronary artery bypass surgery. Design--Thirty-four patients were randomized to centrifugal or roller pump. Platelet activation was studied by flow cytometry before, during and up to 3 days after bypass. Results--Duration of bypass, ischemic period, peripheral anastomoses, hospital stay and mortality did not differ. In roller pump patients, platelet aggregates increased by 250% between end of bypass and 3 h postoperatively (p < 0.001). A secondary, fivefold increase in number of platelet aggregates was found on the 3rd postoperative day (p < 0.001). In the centrifugal pump group, these changes were not significant. Hemolysis increased (20%) at end of bypass and 3 h postoperatively (p < 0.005), and decreased to preoperative levels the next day without group difference. Conclusion--Platelet aggregation was significantly increased in roller compared with centrifugal pump patients, indicating higher susceptibility to postoperative thrombotic complications with the roller pump. Otherwise, there was no clinical evidence for superiority of the centrifugal pump.

  13. Comparison of Performance of Experimental and Conventional Cage Designs and Materials for 75-millimeter-bore Cylindrical Roller Bearings at High Speed

    NASA Technical Reports Server (NTRS)

    Anderson, William J; Macks, E Fred; Nemeth, Zolton N

    1954-01-01

    The results of two investigations, one to determine the relative merits of four experimental and two conventional design 75-millimeter-bore (size 215) cylindrical roller bearings and one to determine the relative merits of nodular iron and bronze as cage materials for this size and type of bearing, are presented in this report. Nine test bearings were operated over a range of dn values (product of bearing bore in mm and shaft speed in r.p.m) from 0.3 x 10(6) to 2.3 x 20(6), radial loads for 7 to 1613 pounds, and oil flows from 2 to 8 pounds per minute with a single-jet circulatory oil feed. Of the six bearings used to evaluate designs, four were experimental types with outer-race-riding cages and inner-race-guided rollers, and two were conventional types, one with outer-race-guided rollers and cage and one with inner-race-guided rollers and cage. Each of these six test bearings was equipped with a different design cage made of nodular iron. The experimental combination of an outer-race-riding cage with a straight-through outer race and inner-race-guided rollers was found to give the best over-all performance based on limiting dn values and bearing temperatures.

  14. EAST ELEVATION, LTV STEEL (FORMERLY REPUBLIC STEEL), 8" BAR MILL, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    EAST ELEVATION, LTV STEEL (FORMERLY REPUBLIC STEEL), 8" BAR MILL, BUFFALO PLANT. VIEW LOOKING SOUTHWEST FROM ROLL SHOP. 8" BAR MILL DESIGNED AND BUILT BY DONNER STEEL CO. (PREDECESSOR OF REPUBLIC), 1919-1920. FOR DESCRIPTION OF ORIGINAL MILL SEE "IRON AGE", 116\\4 (23 JULY 1925): 201-204. - LTV Steel, 8-inch Bar Mill, Buffalo Plant, Buffalo, Erie County, NY

  15. Long-Life, Lightweight, Multi-Roller Traction Drives for Planetary Vehicle Surface Exploration

    NASA Technical Reports Server (NTRS)

    Klein, Richard C.; Fusaro, Robert L.; Dimofte, Florin

    2012-01-01

    NASA s initiative for Lunar and Martian exploration will require long lived, robust drive systems for manned vehicles that must operate in hostile environments. The operation of these mechanical drives will pose a problem because of the existing extreme operating conditions. Some of these extreme conditions include operating at a very high or very cold temperature, operating over a wide range of temperatures, operating in very dusty environments, operating in a very high radiation environment, and operating in possibly corrosive environments. Current drive systems use gears with various configurations of teeth. These gears must be lubricated with oil (or grease) and must have some sort of a lubricant resupply system. For drive systems, oil poses problems such as evaporation, becoming too viscous and eventually freezing at cold temperatures, being too thin to lubricate at high temperatures, being degraded by the radiation environment, being contaminated by the regolith (soil), and if vaporized (and not sealed), it will contaminate the regolith. Thus, it may not be advisable or even possible to use oil because of these limitations. An oil-less, compact traction vehicle drive is a drive designed for use in hostile environments like those that will be encountered on planetary surfaces. Initially, traction roller tests in vacuum were conducted to obtain traction and endurance data needed for designing the drives. From that data, a traction drive was designed that would fit into a prototype lunar rover vehicle, and this design data was used to construct several traction drives. These drives were then tested in air to determine their performance characteristics, and if any final corrections to the designs were necessary. A limitation with current speed reducer systems such as planetary gears and harmonic drives is the high-contact stresses that occur at tooth engagement and in the harmonic drive wave generator interface. These high stresses induce high wear of solid

  16. E2F Transcription Factors Control the Roller Coaster Ride of Cell Cycle Gene Expression.

    PubMed

    Thurlings, Ingrid; de Bruin, Alain

    2016-01-01

    Initially, the E2F transcription factor was discovered as a factor able to bind the adenovirus E2 promoter and activate viral genes. Afterwards it was shown that E2F also binds to promoters of nonviral genes such as C-MYC and DHFR, which were already known at that time to be important for cell growth and DNA metabolism, respectively. These findings provided the first clues that the E2F transcription factor might be an important regulator of the cell cycle. Since this initial discovery in 1987, several additional E2F family members have been identified, and more than 100 targets genes have been shown to be directly regulated by E2Fs, the majority of these are important for controlling the cell cycle. The progression of a cell through the cell cycle is accompanied with the increased expression of a specific set of genes during one phase of the cell cycle and the decrease of the same set of genes during a later phase of the cell cycle. This roller coaster ride, or oscillation, of gene expression is essential for the proper progression through the cell cycle to allow accurate DNA replication and cell division. The E2F transcription factors have been shown to be critical for the temporal expression of the oscillating cell cycle genes. This review will focus on how the oscillation of E2Fs and their targets is regulated by transcriptional, post-transcriptional and post-translational mechanism in mammals, yeast, flies, and worms. Furthermore, we will discuss the functional impact of E2Fs on the cell cycle progression and outline the consequences when E2F expression is disturbed. PMID:26254918

  17. GAD67-GFP+ Neurons in the Nucleus of Roller. II. Subthreshold and Firing Resonance Properties

    PubMed Central

    Berger, A. J.

    2011-01-01

    In the companion paper we show that GAD67-GFP+ (GFP+) inhibitory neurons located in the Nucleus of Roller of the mouse brain stem can be classified into two main groups (tonic and phasic) based on their firing patterns in responses to injected depolarizing current steps. In this study we examined the responses of GFP+ cells to fluctuating sinusoidal (“chirp”) current stimuli. Membrane impedance profiles in response to chirp stimulation showed that nearly all phasic cells exhibited subthreshold resonance, whereas the majority of tonic GFP+ cells were nonresonant. In general, subthreshold resonance was associated with a relatively fast passive membrane time constant and low input resistance. In response to suprathreshold chirp current stimulation at a holding potential just below spike threshold the majority of tonic GFP+ cells fired multiple action potentials per cycle at low input frequencies (<5 Hz) and either stopped firing or were not entrained by the chirp at higher input frequencies (= tonic low-pass cells). A smaller group of phasic GFP+ cells did not fire at low input frequency but were able to phase-lock 1:1 at intermediate chirp frequencies (= band-pass cells). Spike timing reliability was tested with repeated chirp stimuli and our results show that phasic cells were able to reliably fire when they phase-locked 1:1 over a relatively broad range of input frequencies. Most tonic low-pass cells showed low reliability and poor phase-locking ability. Computer modeling suggested that these different firing resonance properties among GFP+ cells are due to differences in passive and active membrane properties and spiking mechanisms. This heterogeneity of resonance properties might serve to selectively activate subgroups of interneurons. PMID:21047931

  18. Corrective Action Plan for Corrective Action Unit 407: Roller Coaster RADSAFE Area, Tonopah Test Range, Nevada

    SciTech Connect

    T. M. Fitzmaurice

    2000-05-01

    This Corrective Action Plan (CAP) has been prepared for the Roller Coaster RADSAFE Area Corrective Action Unit 407 in accordance with the Federal Facility and Consent Order (Nevada Division of Environmental Protection [NDEP] et al., 1996). This CAP provides the methodology for implementing the approved Corrective Action Alternative as listed in the Corrective Action Decision Document (U.S. Department of Energy, Nevada Operations Office, 1999). The RCRSA was used during May and June of 1963 to decontaminate vehicles, equipment, and personnel from the Clean Slate tests. The Constituents of Concern (COCs) identified during the site characterization include plutonium, uranium, and americium. No other COCS were identified. The following closure actions will be implemented under this plan: (1) Remove and dispose of surface soils which are over three times background for the area. Soils identified for removal will be disposed of at an approved disposal facility. Excavated areas will be backfilled with clean borrow soil fi-om a nearby location. (2) An engineered cover will be constructed over the waste disposal pit area where subsurface COCS will remain. (3) Upon completion of the closure and approval of the Closure Report by NDEP, administrative controls, use restrictions, and site postings will be used to prevent intrusive activities at the site. Barbed wire fencing will be installed along the perimeter of this unit. Post closure monitoring will consist of site inspections to determine the condition of the engineered cover. Any identified maintenance and repair requirements will be remedied within 90 working days of discovery and documented in writing at the time of repair. Results of all inspections/repairs for a given year will be addressed in a single report submitted annually to the NDEP.

  19. Closure Report for Corrective Action Unit 407: Roller Coaster RADSAFE Area, Tonopah Test Range, Nevada

    SciTech Connect

    T. M. Fitzmaurice

    2001-12-01

    This closure report (CR) provides documentation for the closure of the Roller Coaster RADSAFE Area (RCRSA) Corrective Action Unit (CAU) 407 identified in the Federal Facility Agreement and Consent Order (FFACO) (Nevada Division of Environmental Protection [NDEP] et al., 1996). CAU 407 is located at the Tonopah Test Range (TTR), Nevada. The TTR is approximately 225 kilometers (km) (140 miles [mi]) northwest of Las Vegas, Nevada (Figure 1). The RCRSA is located on the northeast comer of the intersection of Main Road and Browne's Lake Road, which is approximately 8 km (5 mi) south of Area 3 (Figure 1). The RCRSA was used during May and June of 1963 to decontaminate vehicles, equipment, and personnel from the Double Tracks and Clean Slate tests. Investigation of the RCRSA was conducted from June through November of 1998. A Corrective Action Decision Document (CADD) (U.S. Department of Energy, Nevada Operations Office [DOEN], 1999) was approved in October of 1999. The purpose of this CR is to: Document the closure activities as proposed in the Corrective Action Plan (CAP) (DOEM, 2000). Obtain a Notice of Completion from the NDEP. Recommend the movement of CAU 407 from Appendix III to Appendix IV of the FFACO. The following is the scope of the closure actions implemented for CAU 407: Removal and disposal of surface soils which were over three times background for the area. Soils identified for removal were disposed of at the Area 5 Radioactive Waste Management Site (RWMS) at the Nevada Test Site (NTS). Excavated areas were backfilled with clean borrow soil located near the site. A soil cover was constructed over the waste disposal pit area, where subsurface constituents of concern remain. The site was fenced and posted as an ''Underground Radioactive Material'' area.

  20. The physiological and biomechanical contributions of poling to roller ski skating.

    PubMed

    Sandbakk, Øyvind; Ettema, Gertjan; Holmberg, Hans-Christer

    2013-08-01

    Poling is considered to make a significant contribution to cross-country skiing with the skating technique. To better understand this contribution, the current investigation compared roller ski skating on a treadmill with the so-called G3 skating technique with (G3-P) and without poling (G3-NP). Seven male elite skiers performed 5-min submaximal tests at 8, 12, and 15 km h(-1), as well as an incremental test to exhaustion with both techniques on a 5 % incline. Ventilatory variables were assessed by open-circuit indirect calorimetry and three-dimensional kinematics analyzed using the Qualisys Pro Reflex system. G3-P was associated with approximately 15 % higher peak velocity and 10 % higher peak oxygen uptake than G3-NP in the incremental test (both P < 0.01). All ventilatory variables, as well as heart rate and blood lactate concentration were lower with G3-P as compared to G3-NP at 12 and 15 km h(-1) (all P < 0.01). Gross efficiency (i.e., the ratio of work rate to metabolic rate) at 12 km h(-1) was higher in G3-P (14.9 %) than G3-NP (13.5 %) (P < 0.01). Moreover, with G3-P cycle time and length were both 30 % longer, with correspondingly reduced cycle rates (all P < 0.01). In addition, the ski gliding and swing phases were longer and the angle between the skis smaller with G3-P (both P < 0.01), whereas the push-off time was independent of technique and velocity. Taken together, these results indicate that poling makes an important contribution to propulsion and velocity during ski skating, specifically by enhancing peak oxygen uptake, skiing efficiency and associated biomechanical variables.

  1. Evaluation of some compression aids in tableting of roller compacted swellable core drug layer.

    PubMed

    Golchert, D; Bines, E; Carmody, A

    2013-09-10

    Swellable core technology (SCT) represents a broadly applicable oral osmotic drug delivery platform for the controlled release of drugs. SCT tablets control drug delivery by using osmosis to regulate the influx of water into the tablet's core. The tablet consists of two layers; drug layer and sweller layer, with a semi-permeable membrane coating and delivery port located in the drug layer side of the tablet. The key component of SCT formulations is polyethylene oxide (PEO), which is typically wet granulated with organic solvents to prevent rapid gel hydration observed during contact with aqueous environments. However, the use of organic solvents has their own environmental and cost considerations which make this form of processing undesirable. To overcome this issue, dry granulation can be employed. However, PEO is a very plastic material and problems may be encountered during the tableting process, when work hardening occurs upon double compression. The addition of compression aids to the drug layer will help to increase the roll force when generating ribbons - reducing fines and segregation potential - while also reducing work hardening effects which impact tablet friability. The five compression aids used in this study were microcrystalline cellulose (MCC), xylitol, di-calcium phosphate (anhydrous), lactose monohydrate and starch. The work undertaken here studies the compression properties of the drug layer blends with different levels of the five compression aids as part of the formulation. Roller compaction properties are also varied to provide granules with differing solid fractions. The results of this study indicate that addition of microcrystalline cellulose in the formulation in levels between 10% and 30% significantly improve the tablet hardness at lower tablet compression forces. Further work is required to investigate the impact on dissolution. PMID:23796839

  2. Rolling-contact and wear resistance of hard coatings on bearing-steel substrates

    NASA Astrophysics Data System (ADS)

    Erdemir, A.

    1992-02-01

    Ever-increasing needs for high-performance ball- and roller-bearing components that can endure extreme applications have led to a growing interest in hard coatings for improved fatigue life and wear resistance. In particular, hard TiN and TiC coatings and, quite recently, diamond like carbon films have attracted much attention from manufacturers that produce bearing systems for both rolling- and sliding-contact applications. This paper presents an overview that highlights recent incremental progress in achieving improved fatigue and wear resistance in bearing steels through the use of hard coatings. Effects of coating adhesion, thickness, and morphology on fatigue and wear resistance of hard coatings are discussed in detail. Specific references are made to a few mechanistic models that correlate coating thickness and adhesion to improved fatigue life and wear resistance.

  3. Reducing Wear of Steel Rolling Against Ti6Al4V Operating in Vacuum

    NASA Technical Reports Server (NTRS)

    Krantz, Timothy L.

    2014-01-01

    This work was motivated by a qualification test of a mechanism for a space telescope. During the test undesired wear debris was formed. In this project alterative materials and coatings were tested with intent to reduce wear and debris when steel has a misaligned rolling contact against Ti6Al4V. Testing was done using a vacuum roller rig mimicking the mechanism's contact conditions. Ten configurations were tested. Most configurations resulted in significant debris. A sputtered 1-micrometer-thick nan-ocomposite molybdenum disulfide (MoS2) film provided the best wear protection. The best configuration made use of the MoS2 coating on both materials, and in preparing for sputtering the anodized Ti6Al4V working surface was smoothed using an ultrasonic process.

  4. Performance of large-bore tapered-roller bearings under combined radial and thrust load at shaft speeds to 15,000 rpm

    NASA Technical Reports Server (NTRS)

    Parker, R. J.; Signer, H. R.

    1977-01-01

    The performance of 120.65-mm bore tapered roller bearings was investigated at shaft speeds up to 15,000 rpm. Temperature distribution and bearing heat generation were determined as a function of shaft speed, radial and thrust loads, lubricant flow rate, and lubricant inlet temperature. Lubricant was supplied by either jets or by a combination of holes through the cone directly to the cone-rib contact and jets at the roller small-end side. Cone-rib lubrication significantly improved high-speed tapered-roller bearing performance, yielding lower cone-face temperatures and lower power loss and allowing lower lubricant flow rates for a given speed condition. Bearing temperatures increased with increased shaft speed and decreased with increased lubricant flow rate. Bearing power loss increased with increased shaft speed and increased lubricant flow rate.

  5. Nuclear transmutation in steels

    NASA Astrophysics Data System (ADS)

    Belozerova, A. R.; Shimanskii, G. A.; Belozerov, S. V.

    2009-05-01

    The investigations of the effects of nuclear transmutation in steels that are widely used in nuclear power and research reactors and in steels that are planned for the application in thermonuclear fusion plants, which are employed under the conditions of a prolonged action of neutron irradiation with different spectra, made it possible to study the effects of changes in the isotopic and chemical composition on the tendency of changes in the structural stability of these steels. For the computations of nuclear transmutation in steels, we used a program complex we have previously developed on the basis of algorithms for constructing branched block-type diagrams of nuclide transformations and for locally and globally optimizing these diagrams with the purpose of minimizing systematic errors in the calculation of nuclear transmutation. The dependences obtained were applied onto a Schaeffler diagram for steels used for structural elements of reactors. For the irradiation in fission reactors, we observed only a weak influence of the effects of nuclear transmutation in steels on their structural stability. On the contrary, in the case of irradiation with fusion neutrons, a strong influence of the effects of nuclear transmutation in steels on their structural stability has been noted.

  6. A "roller-wheel" Pt-containing small molecule that outperforms its polymer analogs in organic solar cells

    DOE PAGES

    He, Wenhan; Wu, Qin; Livshits, Maksim Y.; Dickie, Diane A.; Yang, Jianzhong; Quinnett, Rachel; Rack, Jeffrey R.; Qin, Yang

    2016-05-23

    A novel Pt-bisacetylide small molecule (Pt-SM) featuring “roller-wheel” geometry was synthesized and characterized. When compared with conventional Pt-containing polymers and small molecules having “dumbbell” shaped structures, Pt-SM displays enhanced crystallinity and intermolecular π–π interactions, as well as favorable panchromatic absorption behaviors. Furthermore, organic solar cells (OSCs) employing Pt-SM achieve power conversion efficiencies (PCEs) up to 5.9%, the highest reported so far for Pt-containing polymers and small molecules.

  7. Comparison of predicted and experimental performance of large-bore roller bearing operating to 3.0 million DN

    NASA Technical Reports Server (NTRS)

    Coe, H. H.; Huller, F. T.

    1980-01-01

    Bearing inner and outer race temperatures and the amount of heat transferred to the lubricant were calculated by using the computer program CYBEAN. The results obtained were compared with previously reported experimental data for a 118 mm bore roller bearing that operated at shaft speeds to 25,500 rpm, radial loads to 8,900 N (2000 lb), and total lubricant flow rates to 0.0102 cu m/min (2.7 gal/min). The calculated results compared well with the experimental data.

  8. Computer program for analysis of high speed, single row, angular contact, spherical roller bearing, SASHBEAN. Volume 1: User's guide

    NASA Technical Reports Server (NTRS)

    Aggarwal, Arun K.

    1993-01-01

    The computer program SASHBEAN (Sikorsky Aircraft Spherical Roller High Speed Bearing Analysis) analyzes and predicts the operating characteristics of a Single Row, Angular Contact, Spherical Roller Bearing (SRACSRB). The program runs on an IBM or IBM compatible personal computer, and for a given set of input data analyzes the bearing design for it's ring deflections (axial and radial), roller deflections, contact areas and stresses, induced axial thrust, rolling element and cage rotation speeds, lubrication parameters, fatigue lives, and amount of heat generated in the bearing. The dynamic loading of rollers due to centrifugal forces and gyroscopic moments, which becomes quite significant at high speeds, is fully considered in this analysis. For a known application and it's parameters, the program is also capable of performing steady-state and time-transient thermal analyses of the bearing system. The steady-state analysis capability allows the user to estimate the expected steady-state temperature map in and around the bearing under normal operating conditions. On the other hand, the transient analysis feature provides the user a means to simulate the 'lost lubricant' condition and predict a time-temperature history of various critical points in the system. The bearing's 'time-to-failure' estimate may also be made from this (transient) analysis by considering the bearing as failed when a certain temperature limit is reached in the bearing components. The program is fully interactive and allows the user to get started and access most of its features with a minimal of training. For the most part, the program is menu driven, and adequate help messages were provided to guide a new user through various menu options and data input screens. All input data, both for mechanical and thermal analyses, are read through graphical input screens, thereby eliminating any need of a separate text editor/word processor to edit/create data files. Provision is also available to select

  9. Acute, fatal Sarcocystis calchasi-associated hepatitis in Roller pigeons (Columba livia f. dom.) at Philadelphia Zoo.

    PubMed

    Trupkiewicz, J G; Calero-Bernal, R; Verma, S K; Mowery, J; Davison, S; Habecker, P; Georoff, T A; Ialeggio, D M; Dubey, J P

    2016-01-30

    Four Roller pigeons (Columba livia f. dom.) at the Philadelphia Zoo died suddenly. Necropsy examination revealed macroscopic hepatitis. Microscopically, the predominant lesions were in liver, characterized with necrosis and mixed cell inflammatory response. Sarcocystis calchasi-like schizonts and free merozoites were identified in liver. Transmission electron microscopy confirmed that schizonts were in hepatocytes. A few schizonts were in spleen. PCR using S. calchasi-specific primers confirmed the diagnosis. Neither lesions nor protozoa were found in brain and muscles. This is the first report of acute visceral S. calchasi-associated sarcocystosis in naturally infected avian hosts.

  10. Computer program for analysis of high speed, single row, angular contact, spherical roller bearing, SASHBEAN. Volume 1: User's guide

    NASA Astrophysics Data System (ADS)

    Aggarwal, Arun K.

    1993-09-01

    The computer program SASHBEAN (Sikorsky Aircraft Spherical Roller High Speed Bearing Analysis) analyzes and predicts the operating characteristics of a Single Row, Angular Contact, Spherical Roller Bearing (SRACSRB). The program runs on an IBM or IBM compatible personal computer, and for a given set of input data analyzes the bearing design for it's ring deflections (axial and radial), roller deflections, contact areas and stresses, induced axial thrust, rolling element and cage rotation speeds, lubrication parameters, fatigue lives, and amount of heat generated in the bearing. The dynamic loading of rollers due to centrifugal forces and gyroscopic moments, which becomes quite significant at high speeds, is fully considered in this analysis. For a known application and it's parameters, the program is also capable of performing steady-state and time-transient thermal analyses of the bearing system. The steady-state analysis capability allows the user to estimate the expected steady-state temperature map in and around the bearing under normal operating conditions. On the other hand, the transient analysis feature provides the user a means to simulate the 'lost lubricant' condition and predict a time-temperature history of various critical points in the system. The bearing's 'time-to-failure' estimate may also be made from this (transient) analysis by considering the bearing as failed when a certain temperature limit is reached in the bearing components. The program is fully interactive and allows the user to get started and access most of its features with a minimal of training. For the most part, the program is menu driven, and adequate help messages were provided to guide a new user through various menu options and data input screens. All input data, both for mechanical and thermal analyses, are read through graphical input screens, thereby eliminating any need of a separate text editor/word processor to edit/create data files. Provision is also available to select

  11. Effect of Bioregulators Isolated from Rat Liver and Blood Serum on the State of Murine Liver in Roller Organotypic Culture after CCl4-Induced Fibrosis.

    PubMed

    Nalobin, D S; Krasnov, M S; Alipkina, S I; Syrchina, M S; Yamskova, V P; Yamskov, I A

    2016-08-01

    We studied the protective effect of bioregulators isolated from the liver and blood serum of mammals under conditions of manifest fibrosis. Fibrosis was induced by CCl4 administration for 30 days and then, the liver was cultured in a roller organotypic culture for 30 days in the presence of bioregulators. Hepatoprotective effect of bioregulators was evaluated on histological sections of the liver at different terms of culturing. Experiments with roller organotypic culture of the liver isolated from animals with in vivo CCl4-induced fibrosis demonstrated the protective effect of bioregulator of the liver origin, while bioregulator isolated from the blood was ineffective. PMID:27590762

  12. Effect of Bioregulators Isolated from Rat Liver and Blood Serum on the State of Murine Liver in Roller Organotypic Culture after CCl4-Induced Fibrosis.

    PubMed

    Nalobin, D S; Krasnov, M S; Alipkina, S I; Syrchina, M S; Yamskova, V P; Yamskov, I A

    2016-08-01

    We studied the protective effect of bioregulators isolated from the liver and blood serum of mammals under conditions of manifest fibrosis. Fibrosis was induced by CCl4 administration for 30 days and then, the liver was cultured in a roller organotypic culture for 30 days in the presence of bioregulators. Hepatoprotective effect of bioregulators was evaluated on histological sections of the liver at different terms of culturing. Experiments with roller organotypic culture of the liver isolated from animals with in vivo CCl4-induced fibrosis demonstrated the protective effect of bioregulator of the liver origin, while bioregulator isolated from the blood was ineffective.

  13. Rolling-contact fatigue resistance of hard coatings on bearing steels.

    SciTech Connect

    Erdemir, A.

    1999-08-18

    Ball- and roller-bearings of the 21st Century are expected to perform better and last longer while operating under more stringent conditions than before. To meet these great expectations, researchers have been constantly exploring new bearing designs or refining existing ones, optimizing microstructure and chemistry of bearing materials, and alternatively, they have been considering the use of thin hard coatings for improved bearing performance and durability. Already, some laboratory tests have demonstrated that hard nitride, carbide (such as TiN, TiC, etc.) and diamondlike carbon (DLC) coatings can be very effective in prolonging the fatigue lives of bearing steels. This paper provides an overview of the recent developments in hard coatings for bearing applications. Previous studies have demonstrated that thin, hard coatings can effectively prolong the fatigue lives of bearing steel substrates. In particular, thinner hard coatings (i.e., 0.2 - 1 {micro}m thick) provide exceptional improvements in the fatigue lives of bearing steel substrates. In contrast, thicker hard coatings suffer micro fracture and delamination when tested under high contact stresses, hence are ineffective and may even have a negative effect on bearing life. Overall, it was concluded that thin hard coatings may offer new possibilities for bearing industry in meeting the performance and durability needs of the 21st Century.

  14. Internal grinding of high-speed steels: Shorter processing times with boron nitride grinding tools

    NASA Astrophysics Data System (ADS)

    Borse, D.

    Boron nitride grinding tools can be used to advantage for the grinding of high speed steel (HSS) with a high vanadium content. the abrasives available to date are of limited value because the HSS materials contain very hard carbides, grinding of which, and of vanadium carbide in particular, results in very rapid wear in silicon carbide or corundum grinding wheels. The hardness of these steels is usually 62 RC to 70 RC. Boron nitride grinding tools are advantageous for internal grinding of workpieces made of high speed steel for example, sockets, milling tool bores, cutting wheels and crushing rollers. To date, boron nitride grinding wheels or pencil grinders were bonded with synthetic resin. Consequently internal grinding is usually carried out as wet grinding. In the meantime grinding tools bonded with electrodeposited metal bonds (GSS) were developed and proved to be successful for internal grinding. The abrasive grains which are arranged in a single layer protrude freely from the electrobond. During grinding very little heat is generated, so that dry grinding is possible.

  15. Glass Stronger than Steel

    DOE R&D Accomplishments Database

    Yarris, Lynn

    2011-03-28

    A new type of damage-tolerant metallic glass, demonstrating a strength and toughness beyond that of steel or any other known material, has been developed and tested by a collaboration of researchers from Berkeley Lab and Caltech.

  16. Structural Amorphous Steels

    NASA Astrophysics Data System (ADS)

    Lu, Z. P.; Liu, C. T.; Thompson, J. R.; Porter, W. D.

    2004-06-01

    Recent advancement in bulk metallic glasses, whose properties are usually superior to their crystalline counterparts, has stimulated great interest in fabricating bulk amorphous steels. While a great deal of effort has been devoted to this field, the fabrication of structural amorphous steels with large cross sections has remained an alchemist’s dream because of the limited glass-forming ability (GFA) of these materials. Here we report the discovery of structural amorphous steels that can be cast into glasses with large cross-section sizes using conventional drop-casting methods. These new steels showed interesting physical, magnetic, and mechanical properties, along with high thermal stability. The underlying mechanisms for the superior GFA of these materials are discussed.

  17. Life after Steel

    ERIC Educational Resources Information Center

    Mangan, Katherine

    2013-01-01

    Bobby Curran grew up in a working-class neighborhood in Baltimore, finished high school, and followed his grandfather's steel-toed bootprints straight to Sparrows Point, a 3,000-acre sprawl of industry on the Chesapeake Bay. College was not part of the plan. A gritty but well-paying job at the RG Steel plant was Mr. Curran's ticket to a secure…

  18. Comparison of the standard roller pump and a pulsatile centrifugal pump for extracorporeal circulation during routine coronary artery bypass grafting.

    PubMed

    Driessen, J J; Fransen, G; Rondelez, L; Schelstraete, E; Gevaert, L

    1991-01-01

    The present prospective study compared the standard nonpulsatile twin roller pump with the Sarns centrifugal pump, in the pulsatile mode, as arterial pumps for extracorporeal circulation during coronary artery bypass grafting (CABG). The study was conducted in two consecutive groups of 25 patients receiving a standard anaesthetic and surgical protocol. The investigated parameters included haemodynamic profiles, oxygen exchange, blood gas and acid-base homeostasis, haematology, coagulation and complement consumption. With comparable settings for pump flow, gas flow and delivered oxygen concentrations, there was no difference between the groups in the main haemodynamic parameters during cardiopulmonary bypass (CPB). However, a tenfold lower dose of sodium nitroprusside was required to keep systemic vascular resistance within physiologic limits during CPB in the centrifugal group (C group) compared with the roller group (R group). During rewarming oxygen extraction was higher in the C group than in the R group. During the first eight hours after CPB no differences in haemodynamics, oxygenation parameters and pulmonary shunt between the groups were observed. During, as well as after, CPB there was no significant difference in blood gas and acid-base homeostasis between either group. Average postoperative blood loss via chest tubes, total transfusions of blood products, haemoglobin and coagulation did not differ between the two groups. However, the white blood cell count, corrected for changes in haematocrit, decreased during the early phase of CPB in the R group, but not in the C group.(ABSTRACT TRUNCATED AT 250 WORDS)

  19. Roller compaction of hydrophilic extended release tablets-combined effects of processing variables and drug/matrix former particle size.

    PubMed

    Heiman, Johanna; Tajarobi, Farhad; Gururajan, Bindhumadhavan; Juppo, Anne; Abrahmsén-Alami, Susanna

    2015-04-01

    The present study shows that roller compaction (RC) can successfully be used as a granulation method to prepare hydroxypropyl methylcellulose (HPMC)-based extended release matrix tablets containing a high drug load, both for materials deforming mainly by fragmentation (paracetamol) as for those having mainly plastic deformation (ibuprofen). The combined effect of RC process variables and composition on the manufacturability of HPMC tablets was investigated. Standard wet granulation grade HPMC was compared with a larger particle size direct compressible HPMC grade. Higher roll pressure was found to result in larger paracetamol granules and narrower granule particle size distributions, especially for formulations containing smaller size HPMC. However, for ibuprofen, no clear effect of roll pressure was observed. High roll pressure also resulted in denser ribbon and less bypass fines during RC. Loss of compactibility was observed for granules compared to powder blends, which was found to be related to differences in granule porosity and morphology. Using the large-sized HPMC grade did in some cases result in lower tensile strength tablets but had the advantage to improve the powder flow into the roller compactor. This work also indicates that when the HPMC level lies near the percolation threshold, significant changes can occur in the drug release rate due to changes in other factors (raw material characteristics and processing). PMID:25273028

  20. Roller compaction of hydrophilic extended release tablets-combined effects of processing variables and drug/matrix former particle size.

    PubMed

    Heiman, Johanna; Tajarobi, Farhad; Gururajan, Bindhumadhavan; Juppo, Anne; Abrahmsén-Alami, Susanna

    2015-04-01

    The present study shows that roller compaction (RC) can successfully be used as a granulation method to prepare hydroxypropyl methylcellulose (HPMC)-based extended release matrix tablets containing a high drug load, both for materials deforming mainly by fragmentation (paracetamol) as for those having mainly plastic deformation (ibuprofen). The combined effect of RC process variables and composition on the manufacturability of HPMC tablets was investigated. Standard wet granulation grade HPMC was compared with a larger particle size direct compressible HPMC grade. Higher roll pressure was found to result in larger paracetamol granules and narrower granule particle size distributions, especially for formulations containing smaller size HPMC. However, for ibuprofen, no clear effect of roll pressure was observed. High roll pressure also resulted in denser ribbon and less bypass fines during RC. Loss of compactibility was observed for granules compared to powder blends, which was found to be related to differences in granule porosity and morphology. Using the large-sized HPMC grade did in some cases result in lower tensile strength tablets but had the advantage to improve the powder flow into the roller compactor. This work also indicates that when the HPMC level lies near the percolation threshold, significant changes can occur in the drug release rate due to changes in other factors (raw material characteristics and processing).

  1. Waste product profile: Steel cans

    SciTech Connect

    Miller, C.

    1996-07-01

    Steel cans are made from tinplate steel, which is produced in basic oxygen furnaces. A thin layer of tin is applied to the can`s inner and outer surfaces to prevent rusting and protect food and beverage flavors. As a result, steel cans are often called tin cans. Steel mills are the largest market for steel cans. Integrated mills use the basic oxygen process to manufacture tinplate, appliances, car bodies, and steel framing. Electric arc furnaces use 100% scrap to produce steel shapes such as railroad ties and bridge spans. Electric arc furnaces are more geographically diverse and tend to have smaller capacities than basic oxygen furnaces. Detinners remove the tin from steel cans for resale to tin using industries. Continued decreases in the amount of tin used in steel cans has lessened the importance of this market. Foundries use scrap as a raw material in making castings and molds for industrial users.

  2. Articles comprising ferritic stainless steels

    DOEpatents

    Rakowski, James M.

    2016-06-28

    An article of manufacture comprises a ferritic stainless steel that includes a near-surface region depleted of silicon relative to a remainder of the ferritic stainless steel. The article has a reduced tendency to form an electrically resistive silica layer including silicon derived from the steel when the article is subjected to high temperature oxidizing conditions. The ferritic stainless steel is selected from the group comprising AISI Type 430 stainless steel, AISI Type 439 stainless steel, AISI Type 441 stainless steel, AISI Type 444 stainless steel, and E-BRITE.RTM. alloy, also known as UNS 44627 stainless steel. In certain embodiments, the article of manufacture is a fuel cell interconnect for a solid oxide fuel cell.

  3. Profiles in garbage: Steel cans

    SciTech Connect

    Miller, C.

    1998-02-01

    Steel mills are the largest market for steel cans. Integrated mills use the basic oxygen process to manufacture tinplate, appliances, car bodies, and steel framing. Electric arc furnaces use 100% scrap to produce steel shapes such as railroad ties and bridge spans. Electric arc furnaces are more geographically diverse and tend to have smaller capacities than basic oxygen furnaces. Detinners remove the tin from steel cans for resale to tin using industries. With less tin use in steel cans, the importance of the detinning market has declined substantially. Foundries use scrap as a raw material in making castings and molds for industrial users.

  4. Running on Empty: Schools Cope with the Roller-Coaster World of Cost Run-Ups and Budget Let-Downs

    ERIC Educational Resources Information Center

    LaFee, Scott

    2009-01-01

    Public education is like riding a roller-coaster, except that in education the thrill tends to come on the way up, when the economy is flying high, and funding is flush and the future feels as bracing as the wind rushing past. However, this is not one of those times. The economy seems to be almost in free fall. Optimism plummets with each…

  5. Computer program for analysis of high speed, single row, angular contact, spherical roller bearing, SASHBEAN. Volume 2: Mathematical formulation and analysis

    NASA Technical Reports Server (NTRS)

    Aggarwal, Arun K.

    1993-01-01

    Spherical roller bearings have typically been used in applications with speeds limited to about 5000 rpm and loads limited for operation at less than about 0.25 million DN. However, spherical roller bearings are now being designed for high load and high speed applications including aerospace applications. A computer program, SASHBEAN, was developed to provide an analytical tool to design, analyze, and predict the performance of high speed, single row, angular contact (including zero contact angle), spherical roller bearings. The material presented is the mathematical formulation and analytical methods used to develop computer program SASHBEAN. For a given set of operating conditions, the program calculates the bearings ring deflections (axial and radial), roller deflections, contact areas stresses, depth and magnitude of maximum shear stresses, axial thrust, rolling element and cage rotational speeds, lubrication parameters, fatigue lives, and rates of heat generation. Centrifugal forces and gyroscopic moments are fully considered. The program is also capable of performing steady-state and time-transient thermal analyses of the bearing system.

  6. View northwest, wharf A, sheet steel bulkhead, steel lift tower ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View northwest, wharf A, sheet steel bulkhead, steel lift tower - U.S. Coast Guard Sandy Hook Station, Western Docking Structure, West of intersection of Canfield Road & Hartshorne Drive, Highlands, Monmouth County, NJ

  7. Modeling of contact theories for the manipulation of biological micro/nanoparticles in the form of circular crowned rollers based on the atomic force microscope

    SciTech Connect

    Korayem, M. H.; Khaksar, H.; Taheri, M.

    2013-11-14

    This article has dealt with the development and modeling of various contact theories for biological nanoparticles shaped as cylinders and circular crowned rollers for application in the manipulation of different biological micro/nanoparticles based on Atomic Force Microscope. First, the effective contact forces were simulated, and their impact on contact mechanics simulation was investigated. In the next step, the Hertz contact model was simulated and compared for gold and DNA nanoparticles with the three types of spherical, cylindrical, and circular crowned roller type contact geometries. Then by reducing the length of the cylindrical section in the circular crowned roller geometry, the geometry of the body was made to approach that of a sphere, and the results were compared for DNA nanoparticles. To anticipatory validate the developed theories, the results of the cylindrical and the circular crowned roller contacts were compared with the results of the existing spherical contact simulations. Following the development of these contact models for the manipulation of various biological micro/nanoparticles, the cylindrical and the circular crowned roller type contact theories were modeled based on the theories of Lundberg, Dowson, Nikpur, Heoprich, and Hertz for the manipulation of biological micro/nanoparticles. Then, for a more accurate validation, the results obtained from the simulations were compared with those obtained by the finite element method and with the experimental results available in previous articles. The previous research works on the simulation of nanomanipulation have mainly investigated the contact theories used in the manipulation of spherical micro/nanoparticles. However since in real biomanipulation situations, biological micro/nanoparticles of more complex shapes need to be displaced in biological environments, this article therefore has modeled and compared, for the first time, different contact theories for use in the biomanipulation of

  8. Superclean steel development

    SciTech Connect

    Richman, R.H.; McNaughton, W.P. )

    1989-12-01

    The Electric Power Research Institute has actively encouraged and sponsored a number of research projects to develop a superclean 3.5NiCrMoV steel for low pressure turbine rotors. Such steel is highly resistant to temper embrittlement and will thus facilitate increased efficiency in electricity generation through the use of higher operating temperatures and improvements in design. The objective of this interim report was to integrate the results that have been generated to date worldwide in the pursuit of superclean steel. The report contains detailed findings that enable the interested utility to evaluate how the results affect utility decision making. A companion document has been written to summarize the findings from this technical report. The results indicate that steels with impurity contents typical of the superclean specification can be manufactured for production rotors with properties that equal or exceed those for conventional 3.5NiCrMoV rotors in every detail. Of particular interest are the results that the superclean steels appear to be virtually resistant to temper embrittlement to a temperature of 500 {degrees}C. 109 refs., 51 figs., 9 tabs.

  9. Brazing titanium to stainless steel

    NASA Technical Reports Server (NTRS)

    Batista, R. I.

    1980-01-01

    Titanium and stainless-steel members are usually joined mechanically for lack of any other effective method. New approach using different brazing alloy and plating steel member with nickel resolves problem. Process must be carried out in inert atmosphere.

  10. Continuous steel production and apparatus

    DOEpatents

    Peaslee, Kent D.; Peter, Jorg J.; Robertson, David G. C.; Thomas, Brian G.; Zhang, Lifeng

    2009-11-17

    A process for continuous refining of steel via multiple distinct reaction vessels for melting, oxidation, reduction, and refining for delivery of steel continuously to, for example, a tundish of a continuous caster system, and associated apparatus.

  11. A-3 steel work completed

    NASA Technical Reports Server (NTRS)

    2009-01-01

    Stennis Space Center engineers celebrated a key milestone in construction of the A-3 Test Stand on April 9 - completion of structural steel work. Workers with Lafayette (La.) Steel Erector Inc. placed the last structural steel beam atop the stand during a noon ceremony attended by more than 100 workers and guests.

  12. Microbial-Influenced Corrosion of Corten Steel Compared with Carbon Steel and Stainless Steel in Oily Wastewater by Pseudomonas aeruginosa

    NASA Astrophysics Data System (ADS)

    Mansouri, Hamidreza; Alavi, Seyed Abolhasan; Fotovat, Meysam

    2015-07-01

    The microbial corrosion behavior of three important steels (carbon steel, stainless steel, and Corten steel) was investigated in semi petroleum medium. This work was done in modified nutrient broth (2 g nutrient broth in 1 L oily wastewater) in the presence of Pseudomonas aeruginosa and mixed culture (as a biotic media) and an abiotic medium for 2 weeks. The behavior of corrosion was analyzed by spectrophotometric and electrochemical methods and at the end was confirmed by scanning electron microscopy. The results show that the degree of corrosion of Corten steel in mixed culture, unlike carbon steel and stainless steel, is less than P. aeruginosa inoculated medium because some bacteria affect Corten steel less than other steels. According to the experiments, carbon steel had less resistance than Corten steel and stainless steel. Furthermore, biofilm inhibits separated particles of those steels to spread to the medium; in other words, particles get trapped between biofilm and steel.

  13. Less platelet damage in the curved vane centrifugal pump: a comparative study with the roller pump in open heart surgery.

    PubMed

    Nishinaka, T; Nishida, H; Endo, M; Koyanagi, H

    1994-09-01

    The centrifugal pump with the curved vane (Lifestream Centrifugal Pump [LCP]) was applied to cardiopulmonary bypass (CPB) in 10 patients who underwent elective coronary artery bypass grafting. Serum hemoglobin levels, platelet counts, and serum beta-thromboglogulin (beta-TG) levels were measured during CPB. The results were compared with those for a comparative roller pump (RP) group (n = 10). There was no difference in CPB time between LCP (112 +/- 22 min) and RP (121 +/- 22 min) groups. Serum beta-TG levels (ng/ml) were lower in the LCP group than in the RP group (34 +/- 9 vs. 101 +/- 80, 5 min; 81 +/- 33 vs. 236 +/- 112, 30 min; 120 +/- 53 vs. 314 +/- 100, 60 min after initiation of CPB; p < 0.05). There were no significant differences in hemolysis and platelet depletion. The LCP showed excellent hemodynamic performance with less blood trauma in clinical application to open heart surgery.

  14. The influence of non-solvent addition on the independent and dependent parameters in roller electrospinning of polyurethane.

    PubMed

    Cengiz-Callioglu, Funda; Jirsak, Oldrich; Dayik, Mehmet

    2013-07-01

    This paper discusses the effects of 1,1,2,2 tetrachlorethylen (TCE) non-solvent addition on the independent (electrical conductivity, dielectric constant, surface tension and the theological properties of the solution etc.) and dependent parameters (number of Taylor cones per square meter (NTC/m2), spinning performance for one Taylor cone (SP/TC), total spinning performance (SP), fiber properties such as diameter, diameter uniformity, non-fibrous area) in roller electrospinning of polyurethane (PU). The same process parameters (voltage, distance of the electrodes, humidity, etc.) were applied for all solutions during the spinning process. According to the results, the effect of TCE non-solvent concentration on the dielectric constant, surface tension, rheological properties of the solution and also spinning performance was important statistically. Beside these results, TCE non-solvent concentration effects quality of fiber and nano web structure. Generally high fiber density, low non-fibrous percentage and uniform nanofibers were obtained from fiber morphology analyses.

  15. Quantitative fault analysis of roller bearings based on a novel matching pursuit method with a new step-impulse dictionary

    NASA Astrophysics Data System (ADS)

    Cui, Lingli; Wu, Na; Ma, Chunqing; Wang, Huaqing

    2016-02-01

    A novel matching pursuit method based on a new step-impulse dictionary to measure the size of a bearing's spall-like fault is presented in this study. Based on the seemingly double-impact theory and the rolling bearing fault mechanism, a theoretical model for the bearing fault with different spall-like fault sizes is developed and analyzed, and the seemingly double-impact characteristic of the bearing faults is explained. The first action that causes a bearing fault is due to the entry of the roller element into the spall-like fault which can be described as a step-like response. The second action is the exit of the roller element from the spall-like fault, which can be described as an impulse-like response. Based on the quantitative relationship between the time interval of the seemingly double-impact actions and the fault size, a novel matching pursuit method is proposed based on a new step-impulse dictionary. In addition, the quantitative matching pursuit algorithm is proposed for bearing fault diagnosis based on the new dictionary model. Finally, an atomic selection mechanism is proposed to improve the measurement accuracy of bearing fault size. The simulation results of this study indicate that the new matching pursuit method based on the new step-impulse dictionary can be reliably used to measure the sizes of bearing spall-like faults. The applications of this method to the fault signals of bearing outer-races measured at different speeds have shown that the proposed method can effectively measure a bearing's spall-like fault size.

  16. The influence of incline and speed on work rate, gross efficiency and kinematics of roller ski skating.

    PubMed

    Sandbakk, Øyvind; Ettema, Gertjan; Holmberg, Hans-Christer

    2012-08-01

    During competitions, elite cross-country skiers produce higher external work rates on uphill than on flat terrain. However, it is not presently known whether this reflects solely higher energy expenditure. Furthermore, the kinematic factors associated with these higher rates of uphill work have not yet been examined. Therefore, in the present investigation the work rate and associated kinematic parameters at similar metabolic rates during roller ski skating on flat and uphill terrains have been compared. Seven elite male skiers performed six 5-min sub-maximal exercise bouts at the same low, moderate and high metabolic rates on 2 and 8% inclines, while roller skiing on a treadmill employing the G3 skating technique. The work rate was calculated as work against gravity and friction, whereas the energetic equivalent of VO(2) was taken as the metabolic rate. Gross efficiency was defined as work rate divided by metabolic rate. Kinematic parameters were analyzed in three dimensions. At the same metabolic rate, the work rate, cycle rate, work per cycle and relative duration of propulsive phases during a cycle of movement were all higher on the 8% than on the 2% incline at all speeds (all P < 0.05). At similar work rates, gross efficiency was greater on the 8% incline (P < 0.05). In conclusion, these elite skiers consistently demonstrated higher work rates on the 8% incline. To achieve the higher work rates on the steeper incline, these elite skiers employed higher cycle rates and performed more work per cycle, in association with a longer relative propulsive phase.

  17. Braze alloy spreading on steel

    NASA Technical Reports Server (NTRS)

    Siewert, T. A.; Heine, R. W.; Lagally, M. G.

    1978-01-01

    Scanning electron microscopy (SEM) and Auger electron microscopy (AEM) were employed to observe elemental surface decomposition resulting from the brazing of a copper-treated steel. Two types of steel were used for the study, stainless steel (treated with a eutectic silver-copper alloy), and low-carbon steel (treated with pure copper). Attention is given to oxygen partial pressure during the processes; a low enough pressure (8 x 10 to the -5th torr) was found to totally inhibit the spreading of the filler material at a fixed heating cycle. With both types of steel, copper treatment enhanced even spreading at a decreased temperature.

  18. Sensitization of stainless steel

    NASA Technical Reports Server (NTRS)

    Nagy, James P.

    1990-01-01

    The objective of this experiment is to determine the corrosion rates of 18-8 stainless steels that have been sensitized at various temperatures and to show the application of phase diagrams. The laboratory instructor will assign each student a temperature, ranging from 550 C to 1050 C, to which the sample will be heated. Further details of the experimental procedure are detailed.

  19. A comprehensive dynamic model of double-row spherical roller bearing—Model development and case studies on surface defects, preloads, and radial clearance

    NASA Astrophysics Data System (ADS)

    Cao, M.; Xiao, J.

    2008-02-01

    Bearing excitation is one of the most important mechanical sources for vibration and noise generation in machine systems of a broad range of industries. Although extensively investigated, accurately predicting the vibration/acoustic behavior of bearings remains a challenging task because of its complicated nonlinear behaviors. While some ground work has been laid out on single-row deep-grooved ball (DGB) bearing, comprehensive modeling effort on spherical roller bearing (SRB) has yet to be carried out. This is mainly due to the facts that SRB system carries one more extra degree of freedom (DOF) on the moving race (could be either inner or outer race) and in general has more rolling elements compared with DGB. In this study, a comprehensive SRB excitation source model is developed. In addition to the vertical and horizontal displacements considered in previous investigations, the impacts of axial displacement/load are addressed by introducing the DOF in the axial shaft direction. Hence, instead of being treated as pre-assumed constants, the roller-inner/outer race contact angles are formulated as functions of the axial displacement of the moving race to reflect their dependence on the axial movement. The approach presented in this paper accounts for the point contacts between rollers and inner/outer races, as well as line contacts when the loads on individual rollers exceed the limit for point contact. A detailed contact-damping model reflecting the influences of the surface profiles and the speeds of the both contacting elements is developed and applied in the SRB model. Waviness of all the contact surfaces (including inner race, outer race, and rollers) is included and compared in this analysis. Extensive case studies are carried out to reveal the impacts of surface waviness, radial clearance, surface defects, and loading conditions on the force and displacement responses of the SRB system. System design guidelines are recommended based on the simulation results

  20. Comparison of High-Speed Operating Characteristics of Size 215 Cylindrical-Roller Bearings as Determined in Turbojet Engine and in Laboratory Test Rig

    NASA Technical Reports Server (NTRS)

    Macks, E Fred; Nemeth, Zolton N

    1951-01-01

    A comparison of the operating characteristics of 75-millimeter-bore (size 215) cylindrical-roller one-piece inner-race-riding cage-type bearings was made using a laboratory test rig and a turbojet engine. Cooling correlation parameters were determined by means of dimensional analysis, and the generalized results for both the inner- and outer-race bearing operating temperatures are compared for the laboratory test rig and the turbojet engine. Inner- and outer-race cooling-correlation curves were obtained for the turbojet-engine turbine-roller bearing with the same inner- and outer-race correlation parameters and exponents as those determined for the laboratory test-rig bearing. The inner- and outer-race turbine roller-bearing temperatures may be predicted from a single curve, regardless of variations in speed, load, oil flow, oil inlet temperature, oil inlet viscosity, oil-jet diameter or any combination of these parameters. The turbojet-engine turbine-roller-bearing inner-race temperatures were 30 to 60 F greater than the outer-race-maximum temperatures, the exact values depending on the operating condition and oil viscosity; these results are in contrast to the laboratory test-rig results where the inner-race temperatures were less than the outer-race-maximum temperatures. The turbojet-engine turbine-roller bearing, maximum outer-race circumferential temperature variation was approximately 30 F for each of the oils used. The effect of oil viscosity on inner- and outer-race turbojet-engine turbine-roller-bearing temperatures was found to be significant. With the lower viscosity oil (6x10(exp -7) reyns (4.9 centistokes) at 100 F; viscosity index, 83), the inner-race temperature was approximately 30 to 35 F less than with the higher viscosity oil (53x10(exp -7) reyns (42.8 centistokes) at 100 F; viscosity index, 150); whereas the outer-race-maximum temperatures were 12 to 28 F lower with the lower viscosity oil over the DN range investigated.

  1. Special steel production on common carbon steel production line

    NASA Astrophysics Data System (ADS)

    Pi, Huachun; Han, Jingtao; Hu, Haiping; Bian, Ruisheng; Kang, Jianjun; Xu, Manlin

    2004-06-01

    The equipment and technology of small bar tandem rolling line of Shijiazhuang Iron & Steel Co. in China has reached the 90's international advanced level in the 20th century, but products on the line are mostly of common carbon steel. Currently there are few steel plants in China to produce 45 steel bars for cold drawing, which is a kind of shortage product. Development of 45 steel for cold drawing has a wide market outlook in China. In this paper, continuous cooling transformation (CCT) curve of 45 steel for cold drawing used for rolling was set out first. According to the CCT curve, we determined some key temperature points such as Ac3 temperature and Ac1 temperature during the cooling procedure and discussed the precipitation microstructure at different cooling rate. Then by studying thermal treatment process of 45 steel bars for cold drawing, the influence of cooling time on microstructure was analyzed and the optimum cooling speed has been found. All results concluded from the above studies are the basis of regulating controlled cooling process of 45 steel bars for cold drawing. Finally, the feasible production process of 45 steel bars for cold drawing on common carbon steel production line combined with the field condition was recommended.

  2. Ferritic steel melt and FLiBe/steel experiment : melting ferritic steel.

    SciTech Connect

    Troncosa, Kenneth P.; Smith, Brandon M.; Tanaka, Tina Joan

    2004-11-01

    In preparation for developing a Z-pinch IFE power plant, the interaction of ferritic steel with the coolant, FLiBe, must be explored. Sandia National Laboratories Fusion Technology Department was asked to drop molten ferritic steel and FLiBe in a vacuum system and determine the gas byproducts and ability to recycle the steel. We tried various methods of resistive heating of ferritic steel using available power supplies and easily obtained heaters. Although we could melt the steel, we could not cause a drop to fall. This report describes the various experiments that were performed and includes some suggestions and materials needed to be successful. Although the steel was easily melted, it was not possible to drip the molten steel into a FLiBe pool Levitation melting of the drop is likely to be more successful.

  3. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  4. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  5. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  6. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  7. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  8. History of ultrahigh carbon steels

    SciTech Connect

    Wadsworth, J.; Sherby, O.D.

    1997-06-20

    The history and development of ultrahigh carbon steels (i.e., steels containing between 1 and 2.l percent C and now known as UHCS) are described. The early use of steel compositions containing carbon contents above the eutectoid level is found in ancient weapons from around the world. For example, both Damascus and Japanese sword steels are hypereutectoid steels. Their manufacture and processing is of interest in understanding the role of carbon content in the development of modern steels. Although sporadic examples of UHCS compositions are found in steels examined in the early part of this century, it was not until the mid-1970s that the modern study began. This study had its origin in the development of superplastic behavior in steels and the recognition that increasing the carbon content was of importance in developing that property. The compositions that were optimal for superplasticity involved the development of steels that contained higher carbon contents than conventional modern steels. It was discovered, however, that the room temperature properties of these compositions were of interest in their own right. Following this discovery, a period of intense work began on understanding their manufacture, processing, and properties for both superplastic forming and room temperature applications. The development of superplastic cast irons and iron carbides, as well as those of laminated composites containing UHCS, was an important part of this history.

  9. Respiratory status of stainless steel and mild steel welders.

    PubMed

    Kalliomäki, P L; Kalliomäki, K; Korhonen, O; Nordman, H; Rahkonen, E; Vaaranen, V

    1982-01-01

    Eighty-three full-time stainless steel and 29 mild steel welders from one shipyard were examined clinically, and their lung function was measured. The stainless steel welders had used both tungsten inert-gas (low-fume concentration) and manual metal-arc (MMA) (high-fume concentration) welding methods. The individual exposure of the welders was estimated based on the time spent doing MMA welding, the amount of retained contaminants in the lungs (magnetopulmography), and urinary chromium excretion. The results suggest that there is a greater prevalence of small airway disease among shipyard mild steel MMA welders than among stainless steel welders. Among the stainless steel welders the impairment of lung function parameters was associated with the MMA welding method. The type of welding, then, is important when the health hazards of welders are studied, and welders cannot be regarded as a single, homogeneous group. PMID:7100838

  10. Comparison of High-Speed Operating Characteristics of Size 215 Cylindrical-Roller Bearings as Determined in Turbojet Engine and in Laboratory Test Rig

    NASA Technical Reports Server (NTRS)

    Macks, E Fred; Nemeth, Zolton N

    1952-01-01

    A comparison of the operating characteristics of 75-millimeter-bore (size 215) cylindrical-roller one-piece inner-race-riding cage-type bearings was made by means of a laboratory test rig and a turbojet engine. Cooling correlation parameters were determined by means of dimensional analysis, and the generalized results for both the inner- and the outer-race bearing operating temperatures are computed for the laboratory test rig and the turbojet engine. A method is given that enables the designer to predict the inner- and outer-race turbine roller-bearing temperatures from single curves, regardless of variations in speed, load, oil flow, oil inlet temperature, oil inlet viscosity, oil-jet diameter, or any combination of these parameters.

  11. Characterisation of density distributions in roller-compacted ribbons using micro-indentation and X-ray micro-computed tomography.

    PubMed

    Miguélez-Morán, Andres M; Wu, Chuan-Yu; Dong, Hanshan; Seville, Jonathan P K

    2009-05-01

    Roller compaction is one stage in a dry granulation process to produce free flowing granules. Its proper understanding is essential in optimising manufacturing efficiency and product quality. Roller compaction produces a compacted strip or "ribbon", which is then milled to produce granules. For a given milling condition, the density distribution in the ribbons determines the properties of the granules (particularly their size distribution and strength). Therefore, knowing the density distributions in the ribbons is very important in improving the effectiveness of the roller compaction process and the quality of the granules produced. In this paper, the density distribution in roller-compacted ribbons of microcrystalline cellulose (Avicel PH102) has been examined using three different techniques: (1) sectioning; (2) micro-indentation and (3) X-ray micro-computed tomography. It has been shown that with proper calibration all three techniques can essentially produce the same results, but with a different degree of resolution (scale of scrutiny). In addition, the influence of process conditions, such as roll gap, roll speed and the presence or absence of lubrication, on the ribbon density distributions has also been investigated. Flow into the press is often constrained by the presence of "cheek plates", which prevent lateral powder movement. In this type of arrangement, it is found that non-uniform powder feeding occurs in the compaction region, induced by the friction between the powder and the cheek plates; as a result, the densities in the middle of the ribbon width are generally higher than those close to the edges. It has also been shown that higher average ribbon densities are obtained when the roll gap, roll speed, or the friction between the powder and the side cheek plates is reduced.

  12. A hemodynamic evaluation of the Levitronix Pedivas centrifugal pump and Jostra Hl-20 roller pump under pulsatile and nonpulsatile perfusion in an infant CPB model.

    PubMed

    Ressler, Noel; Rider, Alan R; Kunselman, Allen R; Richardson, J Scott; Dasse, Kurt A; Wang, Shigang; Undar, Akif

    2009-01-01

    The hemodynamic comparison of the Jostra HL-20 and the Levitronix PediVAS blood pumps is the focus this study, where pressure-flow waveforms and hemodynamic energy values are analyzed in the confines of a pediatric cardiopulmonary bypass circuit.The pseudo pediatric patient was perfused with flow rates between 500 and 900 ml/min (100 ml/min increments) under pulsatile and nonpulsatile mode. The Levitronix continuous flow pump utilized a customized controller to engage in pulsatile perfusion with equivalent pulse settings to the Jostra HL-20 roller pump. Hemodynamic measurements and waveforms were recorded at the precannula location, while the mean arterial pressure was maintained at 40 mm Hg for each test. Glycerin water was used as the blood analog circuit perfusate. At each flow rate 24 trials were conducted yielding a total of 120 experiments (n=60 pulsatile and n=60 nonpulsatile).Under nonpulsatile perfusion the Jostra roller pump produced small values for surplus hemodynamic energy (SHE) due to its inherent pulsatility, while the Levitronix produced values of essentially zero for SHE. When switching to pulsatile perfusion, the SHE levels for both the Jostra and Levitronix pump made considerable increases. In comparing the two pumps under pulsatile perfusion, the Levitronix PediVAS produced significantly more surplus and total hemodynamic energy than did the Jostra roller pump each pump flow rate.The study suggests that the Levitronix PediVAS centrifugal pump has the capability of achieving quality pulsatile waveforms and delivering more SHE to the pseudo patient than the Jostra HL-20 roller pump. Further studies are warranted to investigate the Levitronix under bovine blood studies and with various pulsatile settings.

  13. Stainless Steel Permeability

    SciTech Connect

    Buchenauer, Dean A.; Karnesky, Richard A.

    2015-09-01

    An understanding of the behavior of hydrogen isotopes in materials is critical to predicting tritium transport in structural metals (at high pressure), estimating tritium losses during production (fission environment), and predicting in-vessel inventory for future fusion devices (plasma driven permeation). Current models often assume equilibrium diffusivity and solubility for a class of materials (e.g. stainless steels or aluminum alloys), neglecting trapping effects or, at best, considering a single population of trapping sites. Permeation and trapping studies of the particular castings and forgings enable greater confidence and reduced margins in the models. For FY15, we have continued our investigation of the role of ferrite in permeation for steels of interest to GTS, through measurements of the duplex steel 2507. We also initiated an investigation of the permeability in work hardened materials, to follow up on earlier observations of unusual permeability in a particular region of 304L forgings. Samples were prepared and characterized for ferrite content and coated with palladium to prevent oxidation. Issues with the poor reproducibility of measurements at low permeability were overcome, although the techniques in use are tedious. Funding through TPBAR and GTS were secured for a research grade quadrupole mass spectrometer (QMS) and replacement turbo pumps, which should improve the fidelity and throughput of measurements in FY16.

  14. Wind-Turbine Gear-Box Roller-Bearing Premature-Failure Caused by Grain-Boundary Hydrogen Embrittlement: A Multi-physics Computational Investigation

    NASA Astrophysics Data System (ADS)

    Grujicic, M.; Chenna, V.; Galgalikar, R.; Snipes, J. S.; Ramaswami, S.; Yavari, R.

    2014-11-01

    To help overcome the problem of horizontal-axis wind-turbine (HAWT) gear-box roller-bearing premature-failure, the root causes of this failure are currently being investigated using mainly laboratory and field-test experimental approaches. In the present work, an attempt is made to develop complementary computational methods and tools which can provide additional insight into the problem at hand (and do so with a substantially shorter turn-around time). Toward that end, a multi-physics computational framework has been developed which combines: (a) quantum-mechanical calculations of the grain-boundary hydrogen-embrittlement phenomenon and hydrogen bulk/grain-boundary diffusion (the two phenomena currently believed to be the main contributors to the roller-bearing premature-failure); (b) atomic-scale kinetic Monte Carlo-based calculations of the hydrogen-induced embrittling effect ahead of the advancing crack-tip; and (c) a finite-element analysis of the damage progression in, and the final failure of a prototypical HAWT gear-box roller-bearing inner raceway. Within this approach, the key quantities which must be calculated using each computational methodology are identified, as well as the quantities which must be exchanged between different computational analyses. The work demonstrates that the application of the present multi-physics computational framework enables prediction of the expected life of the most failure-prone HAWT gear-box bearing elements.

  15. Bilateral internal carotid artery and vertebral artery dissections with retinal artery occlusion after a roller coaster ride - case report and a review.

    PubMed

    Ozkan Arat, Yonca; Volpi, John; Arat, Anıl; Klucznik, Richard; Diaz, Orlando

    2011-01-01

    We present the first case of a woman with no significant medical history who developed dissections of bilateral carotid and bilateral vertebral arteries, as well as a retinal artery occlusion, after a roller coaster ride. A 35-year-old woman developed right-sided neck pain followed by a frontal headache immediately after a roller coaster ride. Five days after the incident, she developed complete loss of vision in her right eye for two hours. Subsequently, the vision improved but remained significantly decreased. On presentation, her visual acuity was 20/200 in the right and 20/20 in the left eye. Her fundus exam revealed retinal edema in the superotemporal retinal artery distribution without any visible emboli. Her neurological exam was otherwise normal. The cerebral angiogram showed bilateral internal carotid and vertebral artery dissections. The patient remained stable with conservative therapy without further worsening of vision or any new neurological deficits. Outcomes for cervicocephalic arterial dissection are usually favorable, but early diagnosis is critical for initiation of appropriate treatment of possible complications. Physicians must have a high index of suspicion for arterial dissection when patients note any headache, neck pain or vertigo triggered by violent motion after leisure activities such as roller coaster rides. PMID:21341139

  16. Process for dezincing galvanized steel

    DOEpatents

    Morgan, William A.; Dudek, Frederick J.; Daniels, Edward J.

    1998-01-01

    A process for removing zinc from galvanized steel. The galvanized steel is immersed in an electrolyte containing at least about 15% by weight of sodium or potassium hydroxide and having a temperature of at least about 75.degree. C. and the zinc is galvanically corroded from the surface of the galvanized steel. The material serving as the cathode is principally a material having a standard electrode potential which is intermediate of the standard electrode potentials of zinc and cadmium in the electrochemical series. The corrosion rate may be accelerated by (i) increasing the number density of corrosion sites in the galvanized steel by mechanically abrading or deforming the galvanized steel, (ii) heating the galvanized steel to form an alloy of zinc on the surface of the galvanized steel, (iii) mixing the galvanized steel with a material having a standard electrode potential which is intermediate of the standard electrode potentials of zinc and cadmium in the electrochemical series, or (iv) moving the galvanized steel relative to itself and to the electrolyte while immersed in the electrolyte.

  17. Process for dezincing galvanized steel

    DOEpatents

    Morgan, W.A.; Dudek, F.J.; Daniels, E.J.

    1998-07-14

    A process is described for removing zinc from galvanized steel. The galvanized steel is immersed in an electrolyte containing at least about 15% by weight of sodium or potassium hydroxide and having a temperature of at least about 75 C and the zinc is galvanically corroded from the surface of the galvanized steel. The material serving as the cathode is principally a material having a standard electrode potential which is intermediate of the standard electrode potentials of zinc and cadmium in the electrochemical series. The corrosion rate may be accelerated by (1) increasing the number density of corrosion sites in the galvanized steel by mechanically abrading or deforming the galvanized steel, (2) heating the galvanized steel to form an alloy of zinc on the surface of the galvanized steel, (3) mixing the galvanized steel with a material having a standard electrode potential which is intermediate of the standard electrode potentials of zinc and cadmium in the electrochemical series, or (4) moving the galvanized steel relative to itself and to the electrolyte while immersed in the electrolyte. 1 fig.

  18. Induction heat treatment of steel

    SciTech Connect

    Semiatin, S.L.; Stutz, D.E.

    1985-01-01

    This book discusses the induction heating. After reviewing heat treating operations for steel and the principles of the heat treatment of steel, an overview of induction heat treating is provided. Next, consideration is given to equipment and equipment selection, coil design, power requirements and temperature control. A discussion of surface and through hardening of steel is provided, including information on frequency and power selection and quenching apparatus. Tempering is considered, followed by information on control of residual stresses, cracking, temper brittleness and the important metallurgical and hardness differences between induction and furnace treated steel.

  19. High strength, tough alloy steel

    DOEpatents

    Thomas, Gareth; Rao, Bangaru V. N.

    1979-01-01

    A high strength, tough alloy steel is formed by heating the steel to a temperature in the austenite range (1000.degree.-1100.degree. C.) to form a homogeneous austenite phase and then cooling the steel to form a microstructure of uniformly dispersed dislocated martensite separated by continuous thin boundary films of stabilized retained austenite. The steel includes 0.2-0.35 weight % carbon, at least 1% and preferably 3-4.5% chromium, and at least one other substitutional alloying element, preferably manganese or nickel. The austenite film is stable to subsequent heat treatment as by tempering (below 300.degree. C.) and reforms to a stable film after austenite grain refinement.

  20. Evaluation of Nominal Contact Area and Contact Pressure Distribution in a Steel-Steel Interface by Means of Ultrasonic Techniques

    NASA Astrophysics Data System (ADS)

    Aymerich, Francesco; Pau, Massimiliano; Ginesu, Francesco

    Analysis of contact interfaces represents one of the most critical engineering problems and involves a huge number of practical applications such as roller bearings, tooth gears, wheel-rail interaction, electrical and thermal couplings, biomechanics etc. While theoretical and numerical approaches to the problem have been extensively studied over the years, only a few experimental techniques have been devised either to validate analytical results, or to infer information non invasively about the state of contact. From the late 1950s onwards, when a relationship was discovered between the amount of energy reflected or transmitted through the contact region and the characteristics of contact, researchers have been employing ultrasonic waves to inspect contact interfaces. Since then, many efforts have been directed towards improving the experimental technique and enhancing the theoretical understanding of ultrasonic waves propagation over an incomplete contact interface. In the light of these considerations, the application of a simple ‘pulse-echo' technique able to investigate the elastoplastic contact of a steel sphere-plate system is proposed in this paper. The main purpose of the analysis is to assess the reliability of the ultrasonic method as a useful tool for assessing a number of contact parameters such as size and shape of contact area, distribution of contact pressure and so on. Experimental data were compared with numerical results obtained using a Finite Element Model (FEM) code. Ultrasonic reflection data were in good agreement with calculated values, thus confirming the effectiveness of the ultrasonic technique as a fast, reliable and non-invasive method in evaluating contact parameters in loaded metallic interfaces.

  1. Non-binding conductor load bearing roller for a gas-insulated transmission line having a corrugated outer conductor

    DOEpatents

    Fischer, William H.

    1984-01-01

    A gas-insulated transmission line includes a corrugated outer conductor, an inner conductor disposed within and insulated from the outer conductor by means of support insulators and an insulating gas, and a non-binding transport device for supporting and permitting movement of the inner conductor/insulating support assembly axially along the corrugated outer conductor without radial displacement and for moving without binding along corrugations of any slope less than vertical. The transport device includes two movable contacts, such as skids or rollers, supported on a common pivot lever, the pivot lever being rotatably disposed about a pivot lever axis, which pivot lever axis is in turn disposed on the periphery of a support insulator or particle trap if one is used. The movable contacts are separated axially a distance equal to the axial distance between the peaks and valleys of the corrugations of the outer conductor and separated radially a distance equal to the radial distance between the peaks and valleys of the corrugations of the outer conductor. The transport device has the pivot lever axis disposed parallel to the motion of travel of the inner conductor/insulating support assembly.

  2. Non-binding conductor load bearing roller for a gas-insulated transmission line having a corrugated outer conductor

    SciTech Connect

    Fischer, W.H.

    1984-04-24

    A gas-insulated transmission line includes a corrugated outer conductor, an inner conductor disposed within and insulated from the outer conductor by means of support insulators and an insulating gas, and a non-binding transport device for supporting and permitting movement of the inner conductor/insulating support assembly axially along the corrugated outer conductor without radial displacement and for moving without binding along corrugations of any slope less than vertical. The transport device includes two movable contacts, such as skids or rollers, supported on a common pivot lever, the pivot lever being rotatably disposed about a pivot lever axis, which pivot lever axis is in turn disposed on the periphery of a support insulator or particle trap if one is used. The movable contacts are separated axially a distance equal to the axial distance between the peaks and valleys of the corrugations of the outer conductor and separated radially a distance equal to the radial distance between the peaks and valleys of the corrugations of the outer conductor. The transport device has the pivot lever axis disposed parallel to the motion of travel of the inner conductor/insulating support assembly. 7 figs.

  3. Biomechanical characteristics and speed adaptation during kick double poling on roller skis in elite cross-country skiers.

    PubMed

    Göpfert, Caroline; Holmberg, Hans-Christer; Stöggl, Thomas; Müller, Erich; Lindinger, Stefan Josef

    2013-06-01

    Recent developments in cross-country ski racing should promote the use of kick double poling. This technique, however, has not been the focus in athletes' training and has barely been investigated. The aims of the present study were to develop a function-based phase definition and to analyse speed adaptation mechanisms for kick double poling in elite cross-country skiers. Joint kinematics and pole/plantar forces were recorded in 10 athletes while performing kick double poling at three submaximal roller skiing speeds. A speed increase was associated with increases in cycle length and rate, while absolute poling and leg push-off durations shortened. Despite maintained impulses of force, the peak and average pole/leg forces increased. During double poling and leg push-off, ranges of motion of elbow flexion and extension increased (p < 0.05) and were maintained for hip/knee flexion and extension. Cycle length increase was correlated to increases in average poling force (r = 0.71) and arm swing time (r = 0.88; both p < 0.05). The main speed adaptation was achieved by changes in double poling technique; however, leg push-off showed high variability among elite skiers, thus illustrating important aspects for technique training.

  4. Blood lactate level responses and comparison with submaximal running and roller skiing in cross-country skiers.

    PubMed

    Cetin, Ebru; Bilgin, Ulviye; Schurmann, Banu Can; Yarim, Imdat; Dölek, Burcu Ertas

    2013-09-01

    The purpose of this study is to examine the effect of 30-minute duration submaximal running and roller skiing exercises, which are among the most important aerobic exercise models in cross-country skiers, on lactic acid levels. The study group comprised 6 female and 4 male athletes (age: 16.87 +/- 1.87 years, body height: 168.35 +/- 5.66 cm, body weight: 56.83 +/- 7.1 kg) who competed in cross-country skiing at national and international level. All athletes participated in the study voluntarily. Measurements were performed three times as basal (1st measurement), immediately after exercise (2nd measurement) and 5 minutes after finishing exercise (3rd measurement).Statistical analysis was conducted using SPSS (version 11.5). A significant increase (P < 0.01) in lactic acid levels was found for both 30-minute submaximal exercise types; however, this effect did not differ statistically between groups. Running exercises caused greater fatigue than skiing exercises, according to percentage values, but the difference in fatigue levels between exercise types was not statistically significant.

  5. Quantitative surface topography assessment of directly compressed and roller compacted tablet cores using photometric stereo image analysis.

    PubMed

    Allesø, Morten; Holm, Per; Carstensen, Jens Michael; Holm, René

    2016-05-25

    Surface topography, in the context of surface smoothness/roughness, was investigated by the use of an image analysis technique, MultiRay™, related to photometric stereo, on different tablet batches manufactured either by direct compression or roller compaction. In the present study, oblique illumination of the tablet (darkfield) was considered and the area of cracks and pores in the surface was used as a measure of tablet surface topography; the higher a value, the rougher the surface. The investigations demonstrated a high precision of the proposed technique, which was able to rapidly (within milliseconds) and quantitatively measure the obtained surface topography of the produced tablets. Compaction history, in the form of applied roll force and tablet punch pressure, was also reflected in the measured smoothness of the tablet surfaces. Generally it was found that a higher degree of plastic deformation of the microcrystalline cellulose resulted in a smoother tablet surface. This altogether demonstrated that the technique provides the pharmaceutical developer with a reliable, quantitative response parameter for visual appearance of solid dosage forms, which may be used for process and ultimately product optimization.

  6. Roller milled black gram (Phaseolus mungo) semolina and its influence on the quality characteristics of high protein pasta.

    PubMed

    Rajiv, Jyotsna; Milind; Inamdar, Aashitosh A; Sakhare, Suresh; Venkateswara Rao, G

    2015-04-01

    Black gram (Phaseolus mungo) was roller milled into semolina (BGS) and was substituted at 25, 50 and 75 % levels in vermicelli making in this investigation. There was an increase in ash and protein content as the inclusion of BGS in blends increased. The quality characteristics of pasta showed marginal increase in cooking loss up to 50 % level of BGS. The firmness value did not change much up to 50 % BGS in pasta. At 75 % level of BGS, the cooking loss and stickiness value were highest (6.10 % and 0. 90 N) whereas firmness value and overall quality score were lowest (4 N and 27.5/40) indicating that the pasta had mushy, indiscrete, sticky strands and had a prominent beany odour making it unacceptable. Hence 50 % BGS was considered optimum in vermicelli. The pasta made with 50 % BGS inclusion had a protein and dietary fiber content of 15.30 % and 8 % as against the control value of 11.30 and 4.20 % respectively. PMID:25829634

  7. The industrial ecology of steel

    SciTech Connect

    Considine, Timothy J.; Jablonowski, Christopher; Considine, Donita M.M.; Rao, Prasad G.

    2001-03-26

    This study performs an integrated assessment of new technology adoption in the steel industry. New coke, iron, and steel production technologies are discussed, and their economic and environmental characteristics are compared. Based upon detailed plant level data on cost and physical input-output relations by process, this study develops a simple mathematical optimization model of steel process choice. This model is then expanded to a life cycle context, accounting for environmental emissions generated during the production and transportation of energy and material inputs into steelmaking. This life-cycle optimization model provides a basis for evaluating the environmental impacts of existing and new iron and steel technologies. Five different plant configurations are examined, from conventional integrated steel production to completely scrap-based operations. Two cost criteria are used to evaluate technology choice: private and social cost, with the latter including the environmental damages associated with emissions. While scrap-based technologies clearly generate lower emissions in mass terms, their emissions of sulfur dioxide and nitrogen oxides are significantly higher. Using conventional damage cost estimates reported in the literature suggests that the social costs associated with scrap-based steel production are slightly higher than with integrated steel production. This suggests that adopting a life-cycle viewpoint can substantially affect environmental assessment of new technologies. Finally, this study also examines the impacts of carbon taxes on steel production costs and technology choice.

  8. Connections: Superplasticity, Damascus Steels, Laminated Steels, and Carbon Dating

    NASA Astrophysics Data System (ADS)

    Wadsworth, Jeffrey

    2016-09-01

    In this paper, a description is given of the connections that evolved from the initial development of a family of superplastic plain carbon steels that came to be known as Ultra-High Carbon Steels (UHCS). It was observed that their very high carbon contents were similar, if not identical, to those of Damascus steels. There followed a series of attempts to rediscover how the famous patterns found on Damascus steels blades were formed. At the same time, in order to improve the toughness at room temperature of the newly-developed UHCS, laminated composites were made of alternating layers of UHCS and mild steel (and subsequently other steels and other metals). This led to a study of ancient laminated composites, the motives for their manufacture, and the plausibility of some of the claims relating to the number of layers in the final blades. One apparently ancient laminated composite, recovered in 1837 from the great pyramid of Giza which was constructed in about 2750 B.C., stimulated a carbon dating study of ancient steels. The modern interest in "Bladesmithing" has connections back to many of these ancient weapons.

  9. Occupational Profiles in the European Steel Industry.

    ERIC Educational Resources Information Center

    Franz, Hans-Werner; And Others

    The steel industry in Europe has faced great changes, with resulting layoffs and restructuring. Now that the most basic changes seem to be over, it has become evident that the remaining steel industry requires more highly trained workers than was the case previously. Although steel maintenance employees were always highly skilled, steel production…

  10. Improving the toughness of ultrahigh strength steel

    SciTech Connect

    Soto, Koji

    2002-08-15

    The ideal structural steel combines high strength with high fracture toughness. This dissertation discusses the toughening mechanism of the Fe/Co/Ni/Cr/Mo/C steel, AerMet 100, which has the highest toughness/strength combination among all commercial ultrahigh strength steels. The possibility of improving the toughness of this steel was examined by considering several relevant factors.

  11. Irradiation effects in ferritic steels

    NASA Astrophysics Data System (ADS)

    Lechtenberg, Thomas

    1985-08-01

    Since 1979 the Alloy Development for Irradiation Performance (ADIP) task funded by the US Department of Energy has been studying the 2-12Cr class of ferritic steels to establish the feasibility of using them in fusion reactor first wall/breeding blanket (FW/B) applications. The advantages of ferritic steels include superior swelling resistance, low thermal stresses compared to austenitic stainless steels, attractive mechanical properties up to 600°C. and service histories exceeding 100 000 h. These steels are commonly used in a range of microstructural conditions which include ferritic, martensitic. tempered martensitic, bainitic etc. Throughout this paper where the term "ferritic" is used it should be taken to mean any of these microstructures. The ADIP task is studying several candidate alloy systems including 12Cr-1MoWV (HT-9), modified 9Cr-1MoVNb, and dual-phased steels such as EM-12 and 2 {1}/{4}Cr-Mo. These materials are ferromagnetic (FM), body centered cubic (bcc), and contain chromium additions between 2 and 12 wt% and molybdenum additions usually below 2%. The perceived issues associated with the application of this class of steel to fusion reactors are the increase in the ductile-brittle transition temperature (DBTT) with neutron damage, the compatibility of these steels with liquid metals and solid breeding materials, and their weldability. The ferromagnetic character of these steels can also be important in reactor design. It is the purpose of this paper to review the current understanding of these bcc steels and the effects of irradiation. The major points of discussion will be irradiation-induced or -enhanced dimensional changes such as swelling and creep, mechanical properties such as tensile strength and various measurements of toughness, and activation by neutron interactions with structural materials.

  12. Welding tritium exposed stainless steel

    SciTech Connect

    Kanne, W.R. Jr.

    1994-11-01

    Stainless steels that are exposed to tritium become unweldable by conventional methods due to buildup of decay helium within the metal matrix. With longer service lives expected for tritium containment systems, methods for welding on tritium exposed material will become important for repair or modification of the systems. Solid-state resistance welding and low-penetration overlay welding have been shown to mitigate helium embrittlement cracking in tritium exposed 304 stainless steel. These processes can also be used on stainless steel containing helium from neutron irradiation, such as occurs in nuclear reactors.

  13. Silk Gland Gene Expression during Larval-Pupal Transition in the Cotton Leaf Roller Sylepta derogata (Lepidoptera: Pyralidae).

    PubMed

    Su, Honghua; Cheng, Yuming; Wang, Zhongyang; Li, Zhong; Stanley, David; Yang, Yizhong

    2015-01-01

    The cotton leaf roller, Sylepta derogata, is a silk-producing insect pest. While young larvae feed on the underside of leaves, the older ones roll cotton leaves and feed on the leaf edges, which defoliates cotton plants. The larvae produce silk to stabilize the rolled leaf and to balloon from used to new leaves. Despite the significance of silk in the biology of pest insect species, there is virtually no information on the genes involved in their silk production. This is a substantial knowledge gap because some of these genes may be valuable targets for developing molecular pest management technologies. We addressed the gap by posing the hypothesis that silk gland gene expression changes during the transition from larvae to pupae. We tested our hypothesis using RNA-seq to investigate changes in silk gland gene expression at three developmental stages, 5th instar larvae (silk producing; 15,445,926 clean reads), prepupae (reduced silk producing; 13,758,154) and pupae (beyond silk producing; 16,787,792). We recorded 60,298 unigenes and mapped 50,158 (larvae), 48,415 (prepupae) and 46,623 (pupae) of them to the NCBI database. Most differentially expressed genes in the 5th instar larvae/prepupae libraries were relevant to nucleotide synthesis and maintenance of silk gland function. We identified down-regulated transcriptional factors and several genes involved in silk formation in the three libraries and verified the expression pattern of eight genes by qPCR. The developmental- and tissue-specific expression patterns of the fibroin light chain gene showed it was highly expressed during the larval silk-producing stage. We recorded highest expression of this gene in the larval silk gland, compared to other tissues, including midgut, hindgut, epidermis, Malpighian tubes, hemolymph and fat body. These data are a genetic resource to guide selection of key genes that may be targeted for in planta and other gene-silencing technologies for sustainable cotton agriculture.

  14. Methoprene influences reproduction and flight capacity in adults of the rice leaf roller, Cnaphalocrocis medinalis (Guenểe) (Lepidoptera: Pyralidae).

    PubMed

    Sun, Bei-Bei; Jiang, Xing-Fu; Zhang, Lei; Stanley, David Warren; Luo, Li-Zhi; Long, Wei

    2013-01-01

    Juvenile hormone (JH) influences many aspects of insect biology, including oogenesis-flight syndrome tradeoffs between migration and reproduction. Drawing on studies of many migratory insects, we posed the hypothesis that JH influences migratory capacity and oogenesis in the rice leaf roller, Cnaphalocrocis medinalis. We treated adults moths (days 1, 2 and 3 postemergence) with the JH analog (JHA), methoprene, and then recorded the influences of JHA treatments on reproduction. JHA treatment on day 1 postemergence, but not on the other days, shortened the preoviposition period, although JHA did not influence total fecundity, oviposition period, or longevity. We infer day 1 postemergence is the JH-sensitive stage to influence reproduction. Therefore, we treated moths on day 1 postemergence with JHA and recorded flight capacity, flight muscle mass, and triacylglycerol (TAG) accumulation. JHA treatments did not influence flight speed, but led to reductions in flight durations and flight distances. At day 3 posttreatment (PT), JHA-treated females flew shorter times and less distance than the controls; JHA-treated males, however, only flew shorter times than the controls. JHA treatments led to reductions in flight muscle mass in females at days 2-3 PT and reductions in TAG content in females at day 3 PT, but, these parameters were not influenced by JHA in males. These findings strongly support our hypothesis, from which we infer that JH is a major driver in C. medinalis oogenesis-flight syndrome tradeoffs. Our data also reveal a JH-sensitive stage in adulthood during which JH influences the oocyte-flight syndrome in C. medinalis.

  15. The role of incline, performance level, and gender on the gross mechanical efficiency of roller ski skating

    PubMed Central

    Sandbakk, Øyvind; Hegge, Ann Magdalen; Ettema, Gertjan

    2013-01-01

    The ability to efficiently utilize metabolic energy to produce work is a key factor for endurance performance. The present study investigated the effects of incline, performance level, and gender on the gross mechanical efficiency during roller ski skating. Thirty-one male and nineteen female elite cross-country skiers performed a 5-min submaximal session at approximately 75% of VO2peak on a 5% inclined treadmill using the G3 skating technique. Thereafter, a 5-min session on a 12% incline using the G2 skating technique was performed at a similar work rate. Gross efficiency was calculated as the external work rate against rolling friction and gravity divided by the metabolic rate using gas exchange. Performance level was determined by the amount of skating FIS points [the Federation of International Skiing (FIS) approved scoring system for ski racing] where fewer points indicate a higher performance level. Strong significant correlations between work rate and metabolic rate within both inclines and gender were revealed (r = −0.89 to 0.98 and P < 0.05 in all cases). Gross efficiency was higher at the steeper incline, both for men (17.1 ± 0.4 vs. 15.8 ± 0.5%, P < 0.05) and women (16.9 ± 0.5 vs. 15.7 ± 0.4%, P < 0.05), but without any gender differences being apparent. Significant correlations between gross efficiency and performance level were found for both inclines and genders (r = −0.65 to 0.81 and P < 0.05 in all cases). The current study demonstrated that cross-country skiers of both genders used less metabolic energy to perform the same amount of work at steeper inclines, and that the better ranked elite male and female skiers skied more efficiently. PMID:24155722

  16. Effect of overhead spray and brush roller treatment on the survival of Pectobacterium and Salmonella on tomato surfaces.

    PubMed

    Balaguero, Alina N; Sreedharan, Aswathy; Schneider, Keith R

    2015-01-01

    Overhead spray and brush roller (OSBR) treatment has been shown to remove significantly more Salmonella from tomato surfaces than flume treatment. However, OSBR is not widely used in tomato packing facilities compared with other commodities, and little is known about whether brushing causes microabrasions or other physical damage. Bacteria such as Pectobacterium, a soft rot-producing plant pathogen, and Salmonella, a human pathogen, show increased survival and growth on damaged tomato surfaces. This study evaluated whether OSBR treatment had a negative effect on the safety and/or marketability of tomatoes by examining its effect on Pectobacterium and Salmonella survival. Pectobacterium survival was evaluated on inoculated tomatoes that were OSBR treated with water or sanitizer (100 ppm of NaOCl, 5 ppm of ClO2, or 80 ppm of peracetic acid). A 15-s OSBR treatment using water or sanitizer achieved a 3-log CFU/ml reduction in Pectobacterium levels. Survival of Pectobacterium and Salmonella on OSBR-treated, untreated, and puncture-wounded tomatoes stored at 25°C and 75 to 85 % relative humidity for 7 days was also assessed. Both Pectobacterium and Salmonella populations declined rapidly on OSBR-treated and untreated tomatoes, indicating that brushing does not damage tomato fruit to the extent of promoting better pathogen survival. In contrast, the survival of both organisms was significantly (P ≤ 0.05) higher on artificially wounded fruit. These results indicate that OSBR treatment does not increase the survival and growth of Pectobacterium or Salmonella on tomato surfaces and that it is effective in reducing Pectobacterium levels on the surface of inoculated tomatoes. These results suggest that, if used properly, an OSBR system in packinghouses is effective in removing surface contamination and does not affect tomato quality or safety. PMID:25581177

  17. Corrective action investigation plan for the Roller Coaster RADSAFE Area, Corrective Action Unit 407, Tonopah Test Range, Nevada

    SciTech Connect

    1998-04-01

    This Corrective Action Investigation Plan (CAIP) has been developed in accordance with the Federal Facility Agreement and Consent Order (FFACO) that was agreed to by the US Department of Energy, Nevada Operations Office (DOE/NV); the State of Nevada Division of Environmental Protection (NDEP); and the US Department of Defense (FFACO, 1996). The CAIP is a document that provides or references all of the specific information for investigation activities associated with Corrective Action Units (CAUs) or Corrective Action Sites (CASs). According to the FFACO (1996), CASs are sites potentially requiring corrective action(s) and may include solid waste management units or individual disposal or release sites. CAUs consist of one or more CASs grouped together based on geography, technical similarity, or agency responsibility for the purpose of determining corrective actions. This CAIP contains the environmental sample collection objectives and the criteria for conducting site investigation activities at CAU No. 407, the Roller Coaster RADSAFE Area (RCRSA) which is located on the Tonopah Test Range (TTR). The TTR, included in the Nellis Air Force Range Complex, is approximately 255 km (140 mi) northwest of Las Vegas, Nevada. CAU No. 407 is comprised of only one CAS (TA-23-001-TARC). The RCRSA was used during May and June 1963 to decontaminate vehicles, equipment, and personnel from the Clean Slate tests. The surface and subsurface soils are likely to have been impacted by plutonium and other contaminants of potential concern (COPCs) associated with decontamination activities at this site. The purpose of the corrective action investigation described in this CAIP is to: identify the presence and nature of COPCs; determine the vertical and lateral extent of COPCs; and provide sufficient information and data to develop and evaluate appropriate corrective actions for the CAS.

  18. Advanced steel reheat furnace

    SciTech Connect

    Moyeda, D.; Sheldon, M.; Koppang, R.; Lanyi, M.; Li, X.; Eleazer, B.

    1997-10-01

    Energy and Environmental Research Corp. (EER) under a contract from the Department of Energy is pursuing the development and demonstration of an Advanced Steel Reheating Furnace. This paper reports the results of Phase 1, Research, which has evaluated an advanced furnace concept incorporating two proven and commercialized technologies previously applied to other high temperature combustion applications: EER`s gas reburn technology (GR) for post combustion NOx control; and Air Product`s oxy-fuel enrichment air (OEA) for improved flame heat transfer in the heating zones of the furnace. The combined technologies feature greater production throughput with associated furnace efficiency improvements; lowered NOx emissions; and better control over the furnace atmosphere, whether oxidizing or reducing, leading to better control over surface finish.

  19. 2169 steel waveform experiments.

    SciTech Connect

    Furnish, Michael David; Alexander, C. Scott; Reinhart, William Dodd; Brown, Justin L.

    2012-11-01

    In support of LLNL efforts to develop multiscale models of a variety of materials, we have performed a set of eight gas gun impact experiments on 2169 steel (21% Cr, 6% Ni, 9% Mn, balance predominantly Fe). These experiments provided carefully controlled shock, reshock and release velocimetry data, with initial shock stresses ranging from 10 to 50 GPa (particle velocities from 0.25 to 1.05 km/s). Both windowed and free-surface measurements were included in this experiment set to increase the utility of the data set, as were samples ranging in thickness from 1 to 5 mm. Target physical phenomena included the elastic/plastic transition (Hugoniot elastic limit), the Hugoniot, any phase transition phenomena, and the release path (windowed and free-surface). The Hugoniot was found to be nearly linear, with no indications of the Fe phase transition. Releases were non-hysteretic, and relatively consistent between 3- and 5-mmthick samples (the 3 mm samples giving slightly lower wavespeeds on release). Reshock tests with explosively welded impactors produced clean results; those with glue bonds showed transient releases prior to the arrival of the reshock, reducing their usefulness for deriving strength information. The free-surface samples, which were steps on a single piece of steel, showed lower wavespeeds for thin (1 mm) samples than for thicker (2 or 4 mm) samples. A configuration used for the last three shots allows release information to be determined from these free surface samples. The sample strength appears to increase with stress from ~1 GPa to ~ 3 GPa over this range, consistent with other recent work but about 40% above the Steinberg model.

  20. Microneedles rollers as a potential device to increase ALA diffusion and PpIX production: evaluations by wide-field fluorescence imaging and fluorescence spectroscopy

    NASA Astrophysics Data System (ADS)

    Gracielli Sousa, R. Phamilla; de Menezes, Priscila F. C.; Fujita, Alessandra K. L.; Requena, Michelle B.; Govone, Angelo Biassi; Escobar, André; de Nardi, Andrigo B.; Kurachi, Cristina; Bagnato, Vanderlei Salvador

    2014-03-01

    One of the limitations of topical photodynamic therapy (PDT) using 5-aminolevulinic acid (ALA) is the poor ability to penetrate biological barriers of skin and the recurrence rates in treatments. This study aimed to identify possible signs of increased diffusion of ALA-induced PpIX by fluorescence images and fluorescence spectroscopy. The research was done using in vivo porcine skin model. Before the cream application, microholes was performed with microneedles rollers in only one direction, afterward the ALA cream was applied at a 2.5cm2 area in triplicate and an occlusive dressing was placed. PpIX production was monitored using fluorescence spectroscopy collected at skin surface after 70, 100, 140, and 180 minutes of ALA incubation. About 100 fluorescence spectra of each treatment were collected, distributed by about five points for each site. Wide-field fluorescence imaging was made after 70, 90, and 170 minutes after treatment. The results obtained by imaging analysis indicated increase of the PpIX diffusion in the skin surface using the microneedles rollers (MNs) before ALA application. Circular regions of red fluorescence around the microholes were observed. In addition, the fluorescence spectra showed a greater intensity (2 times as many) in groups microneedles rollers associated. In conclusion, our data shown greater homogeneity and PpIX production in the groups pre-treated with microneedles indicating that the technique can be used to greater uniformity of PpIX production throughout the area to be treated reducing the chances of recurrent tumor as well as has potential for decreasing the time of therapy. (FUNDING SUPPORT:CAPES, CNPq and FAPESP)

  1. Near-infrared spectroscopic analysis of the breaking force of extended-release matrix tablets prepared by roller-compaction: influence of plasticizer levels and sintering temperature.

    PubMed

    Dave, Vivek S; Fahmy, Raafat M; Hoag, Stephen W

    2015-06-01

    The aim of this study was to investigate the feasibility of near-infrared (NIR) spectroscopy for the determination of the influence of sintering temperature and plasticizer levels on the breaking force of extended-release matrix tablets prepared via roller-compaction. Six formulations using theophylline as a model drug, Eudragit® RL PO or Eudragit® RS PO as a matrix former and three levels of TEC (triethyl citrate) as a plasticizer were prepared. The powder blend was roller compacted using a fixed roll-gap of 1.5 mm, feed screw speed to roller speed ratio of 5:1 and roll pressure of 4 MPa. The granules, after removing fines, were compacted into tablets on a Stokes B2 rotary tablet press at a compression force of 7 kN. The tablets were thermally treated at different temperatures (Room Temperature, 50, 75 and 100 °C) for 5 h. These tablets were scanned in reflectance mode in the wavelength range of 400-2500 nm and were evaluated for breaking force. Tablet breaking force significantly increased with increasing plasticizer levels and with increases in the sintering temperature. An increase in tablet hardness produced an upward shift (increase in absorbance) in the NIR spectra. The principle component analysis (PCA) of the spectra was able to distinguish samples with different plasticizer levels and sintering temperatures. In addition, a 9-factor partial least squares (PLS) regression model for tablets containing Eudragit® RL PO had an r(2) of 0.9797, a standard error of calibration of 0.6255 and a standard error of cross validation (SECV) of 0.7594. Similar analysis of tablets containing Eudragit® RS PO showed an r(2) of 0.9831, a standard error of calibration of 0.9711 and an SECV of 1.192.

  2. Investigation of the Phase Formation of AlSi-Coatings for Hot Stamping of Boron Alloyed Steel

    SciTech Connect

    Veit, R.; Kolleck, R.; Hofmann, H.; Sikora, S.

    2011-01-17

    Hot stamping of boron alloyed steel is gaining more and more importance for the production of high strength automotive body parts. Within hot stamping of quenchenable steels the blank is heated up to austenitization temperature, transferred to the tool, formed rapidly and quenched in the cooled tool. To avoid scale formation during the heating process of the blank, the sheet metal can be coated with an aluminium-silicum alloy. The meltimg temperature of this coating is below the austenitization temperature of the base material. This means, that a diffusion process between base material and coating has to take place during heating, leading to a higher melting temperature of the coating.In conventional heating devices, like roller hearth furnaces, the diffusion process is reached by relatively low heating rates. New technologies, like induction heating, reach very high heating rates and offer great potentials for the application in hot stamping. Till now it is not proofed, that this technology can be used with aluminum-silicon coated materials. This paper will present the results of comparative heating tests with a conventional furnace and an induction heating device. For different time/temperature-conditions the phase formation within the coating will be described.

  3. Investigation of the Phase Formation of AlSi-Coatings for Hot Stamping of Boron Alloyed Steel

    NASA Astrophysics Data System (ADS)

    Veit, R.; Hofmann, H.; Kolleck, R.; Sikora, S.

    2011-01-01

    Hot stamping of boron alloyed steel is gaining more and more importance for the production of high strength automotive body parts. Within hot stamping of quenchenable steels the blank is heated up to austenitization temperature, transferred to the tool, formed rapidly and quenched in the cooled tool. To avoid scale formation during the heating process of the blank, the sheet metal can be coated with an aluminium-silicum alloy. The meltimg temperature of this coating is below the austenitization temperature of the base material. This means, that a diffusion process between base material and coating has to take place during heating, leading to a higher melting temperature of the coating. In conventional heating devices, like roller hearth furnaces, the diffusion process is reached by relatively low heating rates. New technologies, like induction heating, reach very high heating rates and offer great potentials for the application in hot stamping. Till now it is not proofed, that this technology can be used with aluminum-silicon coated materials. This paper will present the results of comparative heating tests with a conventional furnace and an induction heating device. For different time/temperature-conditions the phase formation within the coating will be described.

  4. Corrosion of Steels in Steel Reinforced Concrete in Cassava Juice

    NASA Astrophysics Data System (ADS)

    Oluwadare, G. O.; Agbaje, O.

    The corrosion of two types of construction steels, ST60Mn and RST37-2♦, in a low cyanide concentration environment (cassava juice) and embedded in concrete had been studied. The ST60 Mn was found to be more corrosion resistant in both ordinary water and the cassava juice environment. The cyanide in cassava juice does not attack the steel but it provides an environment of lower pH around the steel in the concrete which leads to breakdown of the passivating film provided by hydroxyl ions from cement. Other factors such as the curing time of the concrete also affect the corrosion rates of the steel in the concrete. The corrosion rate of the steel directly exposed to cassava juice i.e., steel not embedded in concrete is about twice that in concrete. Long exposure of concrete structure to cassava processing effluent might result in deterioration of such structures. Careful attention should therefore be paid to disposal of cassava processing effluents, especially in a country like Nigeria where such processing is now on the increase.

  5. Great Lakes Steel -- PCI facility

    SciTech Connect

    Eichinger, F.T.; Dake, S.H.; Wagner, E.D.; Brown, G.S.

    1997-12-31

    This paper discusses the planning, design, and start-up of the 90 tph PCI facility for National Steel`s Great Lakes Steel Division in River Rouge, MI. This project is owned and operated by Edison Energy Services, and was implemented on a fast-track basis by Raytheon Engineers and Constructors, Babcock Material Handling, and Babcock and Wilcox. This paper presents important process issues, basic design criteria, an the challenges of engineering and building a state-of-the-art PCI facility in two existing plants. Pulverized coal is prepared at the River Rouge Power Plant of Detroit Edison, is pneumatically conveyed 6,000 feet to a storage silo at Great Lakes Steel, and is injected into three blast furnaces.

  6. Hydrogen embrittlement of structural steels.

    SciTech Connect

    Somerday, Brian P.

    2010-06-01

    Carbon-manganese steels are candidates for the structural materials in hydrogen gas pipelines, however it is well known that these steels are susceptible to hydrogen embrittlement. Decades of research and industrial experience have established that hydrogen embrittlement compromises the structural integrity of steel components. This experience has also helped identify the failure modes that can operate in hydrogen containment structures. As a result, there are tangible ideas for managing hydrogen embrittement in steels and quantifying safety margins for steel hydrogen containment structures. For example, fatigue crack growth aided by hydrogen embrittlement is a key failure mode for steel hydrogen containment structures subjected to pressure cycling. Applying appropriate structural integrity models coupled with measurement of relevant material properties allows quantification of safety margins against fatigue crack growth in hydrogen containment structures. Furthermore, application of these structural integrity models is aided by the development of micromechanics models, which provide important insights such as the hydrogen distribution near defects in steel structures. The principal objective of this project is to enable application of structural integrity models to steel hydrogen pipelines. The new American Society of Mechanical Engineers (ASME) B31.12 design code for hydrogen pipelines includes a fracture mechanics-based design option, which requires material property inputs such as the threshold for rapid cracking and fatigue crack growth rate under cyclic loading. Thus, one focus of this project is to measure the rapid-cracking thresholds and fatigue crack growth rates of line pipe steels in high-pressure hydrogen gas. These properties must be measured for the base materials but more importantly for the welds, which are likely to be most vulnerable to hydrogen embrittlement. The measured properties can be evaluated by predicting the performance of the pipeline

  7. Wear of steel by rubber

    NASA Technical Reports Server (NTRS)

    Gent, A. N.; Pulford, C. T. R.

    1978-01-01

    Wear of a steel blade used as a scraper to abrade rubber surfaces has been found to take place much more rapidly on a cis-polyisoprene (natural rubber) surface than on a cis-polybutadiene surface, and much more rapidly in an inert atmosphere than in air. These observations are attributed to the direct attack upon steel of free-radical species generated by mechanical rupture of elastomer molecules during abrasion.

  8. Fatigue handbook: Offshore steel structures

    SciTech Connect

    Almarnaess, A.

    1985-01-01

    The contents of this book are: Overview of Offshore Steel Structures; Loads on Ocean Structures; Fracture Mechanics As a Tool in Fatigue Analysis; Basic Fatigue Properties of Welded Joints; Significance of Defects; Improving the Fatigue Strength of Welded Joints; Effects of Marine Environment and Cathodic Protection on Fatigue of Structural Steels Fatigue of Tubular Joints; Unstable Fracture; Fatigue Life Calculations; and Fatigue in Building Codes Background and Applications.

  9. Development of New Stainless Steel

    SciTech Connect

    Robert F. Buck

    2005-08-30

    A new family of innovative martensitic stainless steels, 521-A, 521-B, and 521-C has been developed by Advanced Steel Technology, LLC (Trafford, PA) as high strength fastener (bolt) materials for use at moderate temperatures in turbine engines, including steam turbines, gas turbines, and aircraft engines. The primary objective of the development program was to create a martensitic stainless steel with high strength at moderate temperatures, and which could replace the expensive nickel-based superalloy IN 718 in some fasteners applications. A secondary objective was to replace conventional 12Cr steels such as AISI 422 used as blades, buckets and shafts that operate at intermediate temperatures in turbine engines with stronger steel. The composition of the new alloys was specifically designed to produce excellent mechanical properties while integrating heat treatment steps into production to reduce energy consumption during manufacturing. As a result, production costs and energy consumption during production of rolled bar products is significantly lower than conventional materials. Successful commercialization of the new alloys would permit the installed cost of certain turbine engines to be reduced without sacrificing high availability or operational flexibility, thereby enhancing the global competitiveness of U.S. turbine engine manufacturers. Moreover, the domestic specialty steel industry would also benefit through increased productivity and reduced operating costs, while increasing their share of the international market for turbine engine fasteners, blades, buckets and shafts.

  10. Hydrogen Permeation in Nanostructured Bainitic Steel

    NASA Astrophysics Data System (ADS)

    Kazum, Oluwole; Beladi, Hossein; Timokhina, Ilana B.; He, Yinghe; Bobby Kannan, M.

    2016-07-01

    Hydrogen permeation of nanostructured bainitic steel, produced at two different transformation temperatures, i.e., 473.15 K (200 °C) BS-200 and 623.15 K (350 °C) BS-350, was determined using Devanathan-Stachurski hydrogen permeation cell and compared with that of mild steel. Nanostructured bainitic steel showed lower effective diffusivity of hydrogen as compared to the mild steel. The BS-200 steel, which exhibited higher volume fraction of bainitic ferrite phase, showed lower effective diffusivity than BS-350 steel. The finer microstructural constituents (bainitic ferrite laths and retained austenite films) and higher dislocation density in the bainitic ferrite phase of BS-200 steel can be attributed to its lower effective diffusivity as compared to BS-350 steel and mild steel.

  11. Hydrogen Permeation in Nanostructured Bainitic Steel

    NASA Astrophysics Data System (ADS)

    Kazum, Oluwole; Beladi, Hossein; Timokhina, Ilana B.; He, Yinghe; Bobby Kannan, M.

    2016-10-01

    Hydrogen permeation of nanostructured bainitic steel, produced at two different transformation temperatures, i.e., 473.15 K (200 °C) BS-200 and 623.15 K (350 °C) BS-350, was determined using Devanathan-Stachurski hydrogen permeation cell and compared with that of mild steel. Nanostructured bainitic steel showed lower effective diffusivity of hydrogen as compared to the mild steel. The BS-200 steel, which exhibited higher volume fraction of bainitic ferrite phase, showed lower effective diffusivity than BS-350 steel. The finer microstructural constituents (bainitic ferrite laths and retained austenite films) and higher dislocation density in the bainitic ferrite phase of BS-200 steel can be attributed to its lower effective diffusivity as compared to BS-350 steel and mild steel.

  12. Fast fabrication of nano-structured anti-reflection layers for enhancement of solar cells performance using plasma sputtering and infrared assisted roller embossing techniques.

    PubMed

    Liu, Shih-Jung; Liao, Che-Ting

    2012-02-27

    This paper reports the continuous fabrication of dual-side nano-structured anti-reflection protective layer for performance enhancement of solar cells using plasma sputtering and infrared assisted roller embossing techniques. Nano-structures were first deposited onto the surface of glass substrates using the plasma sputtering technique. After electroforming, a nickel master mold containing nano-array of 30 nm was obtained. The mold was then attached to the surfaces of the two metallic rollers in an infrared assisted roll-to-roll embossing facility. The embossing facility was used to replicate the nano-structures onto 60 μm thick polyethylene terephthalate (PET) films in the experiments. The embossed films were characterized using UV-vis spectrophotometer, atomic force microscope (AFM), and scanning electron microscope (SEM); its total conversion efficiency for solar cells was also measured by a solar simulator. The experimental results showed that the fabricated films could effectively reduce the reflectance and increase the conversion efficiency of solar cells. The proposed method shows great potential for fast fabrication of the anti-reflection protective layer of solar cells due to its simplicity and versatility.

  13. Review on Cold-Formed Steel Connections

    PubMed Central

    Tan, Cher Siang; Mohammad, Shahrin; Md Tahir, Mahmood; Shek, Poi Ngian

    2014-01-01

    The concept of cold-formed light steel framing construction has been widespread after understanding its structural characteristics with massive research works over the years. Connection serves as one of the important elements for light steel framing in order to achieve its structural stability. Compared to hot-rolled steel sections, cold-formed steel connections perform dissimilarity due to the thin-walled behaviour. This paper aims to review current researches on cold-formed steel connections, particularly for screw connections, storage rack connections, welded connections, and bolted connections. The performance of these connections in the design of cold-formed steel structures is discussed. PMID:24688448

  14. Review on cold-formed steel connections.

    PubMed

    Lee, Yeong Huei; Tan, Cher Siang; Mohammad, Shahrin; Tahir, Mahmood Md; Shek, Poi Ngian

    2014-01-01

    The concept of cold-formed light steel framing construction has been widespread after understanding its structural characteristics with massive research works over the years. Connection serves as one of the important elements for light steel framing in order to achieve its structural stability. Compared to hot-rolled steel sections, cold-formed steel connections perform dissimilarity due to the thin-walled behaviour. This paper aims to review current researches on cold-formed steel connections, particularly for screw connections, storage rack connections, welded connections, and bolted connections. The performance of these connections in the design of cold-formed steel structures is discussed.

  15. Review on cold-formed steel connections.

    PubMed

    Lee, Yeong Huei; Tan, Cher Siang; Mohammad, Shahrin; Tahir, Mahmood Md; Shek, Poi Ngian

    2014-01-01

    The concept of cold-formed light steel framing construction has been widespread after understanding its structural characteristics with massive research works over the years. Connection serves as one of the important elements for light steel framing in order to achieve its structural stability. Compared to hot-rolled steel sections, cold-formed steel connections perform dissimilarity due to the thin-walled behaviour. This paper aims to review current researches on cold-formed steel connections, particularly for screw connections, storage rack connections, welded connections, and bolted connections. The performance of these connections in the design of cold-formed steel structures is discussed. PMID:24688448

  16. 38. Photocopy of photograph. STEEL PLANT, BOILERS UNDER CONSTRUCTION IN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    38. Photocopy of photograph. STEEL PLANT, BOILERS UNDER CONSTRUCTION IN BOILER PLANT LOCATED EAST OF MAIN STEEL PLANT, 1909. (From the Bethlehem Steel Corporation collection, Seattle, WA) - Irondale Iron & Steel Plant, Port Townsend, Jefferson County, WA

  17. Corrective Action Decision Document for Corrective Action Unit 407: Roller Coaster RADSAFE Area, Tonopah Test Range, Nevada

    SciTech Connect

    U.S. Department of Energy, Nevada Operations Office

    1999-09-24

    This Corrective Action Decision Document identifies and rationalizes the U.S. Department of Energy, Nevada Operations Office's selection of a recommended corrective action alternative (CAA) appropriate to facilitate the closure of Corrective Action Unit (CAU) 407, Roller Coaster RADSAFE Area (RCRSA), under the Federal Facility Agreement and Consent Order. Located on Tonopah Test Range (TTR), CAU 407 is located approximately 140 miles northwest of Las Vegas, Nevada, and five miles south of Area 3. The RCRSA was used during May and June of 1963 to decontaminate vehicles, equipment, and personnel from the Clean Slate tests. As a result of these operations, the surface and subsurface soils in the area have been impacted by plutonium and other contaminants of potential concern associated with decontamination activities. In June and July 1998, corrective action investigation activities were performed at CAU 407 (as outlined in the related Corrective Action Investigation Plan [CAIP]). The purpose of this investigation was to determine if any analytes were present at the site in concentrations above the preliminary action levels (PALs). The results indicated in the detection of plutonium above the PAL in samples taken from surface and subsurface soil within the exclusion zone, and uranium and americium detected above the PAL in samples taken from surface soil within the exclusion zone. No other COCs were identified above PALs specified in the CAIP. Based on this data, two corrective action objectives (CAOs) were defined: (1) to prevent or mitigate human exposure to surface and subsurface soil containing COCs, and (2) to prevent adverse impacts to groundwater quality. To accomplish these objectives, five CAAs were developed and evaluated. Based on the results of the detailed and comparative analysis of these alternatives, Alternative 3 (Partial Excavation, Disposal, and Administrative Controls With a Surface Cap) was chosen as the preferred alternative. This alternative was

  18. Silk Gland Gene Expression during Larval-Pupal Transition in the Cotton Leaf Roller Sylepta derogata (Lepidoptera: Pyralidae).

    PubMed

    Su, Honghua; Cheng, Yuming; Wang, Zhongyang; Li, Zhong; Stanley, David; Yang, Yizhong

    2015-01-01

    The cotton leaf roller, Sylepta derogata, is a silk-producing insect pest. While young larvae feed on the underside of leaves, the older ones roll cotton leaves and feed on the leaf edges, which defoliates cotton plants. The larvae produce silk to stabilize the rolled leaf and to balloon from used to new leaves. Despite the significance of silk in the biology of pest insect species, there is virtually no information on the genes involved in their silk production. This is a substantial knowledge gap because some of these genes may be valuable targets for developing molecular pest management technologies. We addressed the gap by posing the hypothesis that silk gland gene expression changes during the transition from larvae to pupae. We tested our hypothesis using RNA-seq to investigate changes in silk gland gene expression at three developmental stages, 5th instar larvae (silk producing; 15,445,926 clean reads), prepupae (reduced silk producing; 13,758,154) and pupae (beyond silk producing; 16,787,792). We recorded 60,298 unigenes and mapped 50,158 (larvae), 48,415 (prepupae) and 46,623 (pupae) of them to the NCBI database. Most differentially expressed genes in the 5th instar larvae/prepupae libraries were relevant to nucleotide synthesis and maintenance of silk gland function. We identified down-regulated transcriptional factors and several genes involved in silk formation in the three libraries and verified the expression pattern of eight genes by qPCR. The developmental- and tissue-specific expression patterns of the fibroin light chain gene showed it was highly expressed during the larval silk-producing stage. We recorded highest expression of this gene in the larval silk gland, compared to other tissues, including midgut, hindgut, epidermis, Malpighian tubes, hemolymph and fat body. These data are a genetic resource to guide selection of key genes that may be targeted for in planta and other gene-silencing technologies for sustainable cotton agriculture. PMID

  19. Determinants of a simulated cross-country skiing sprint competition using V2 skating technique on roller skis.

    PubMed

    Mikkola, Jussi; Laaksonen, Marko; Holmberg, Hans-Christer; Vesterinen, Ville; Nummela, Ari

    2010-04-01

    The present study investigated the performance-predicting factors of a simulated cross-country (XC) skiing sprint competition on roller skis, on a slow surface. Sixteen elite male XC skiers performed a simulated sprint competition (4 x 850 m heat with a 20-minute recovery) using V2 skating technique on an indoor tartan track. Heat velocities, oxygen consumption, and peak lactate were measured during or after the heats. Maximal skiing velocity was measured by performing a 30-m speed test. Explosive and maximal force production in the upper body was determined by bench press (BP). Subjects also performed maximal anaerobic skiing test (MAST) and the 2 x 2-km double poling (DP) test. The maximal velocity of MAST (VMAST) and velocities at 3 (V3), 5 (V5), 7 (V7) mmol.L lactate levels in MAST were determined. In the 2 x 2-km test, DP economy (VO2SUBDP) and maximal 2-km DP velocity (VDP2KM) were determined. The best single performance-predicting factors for the sprint performance were VDP2KM (r = 0.73, p < 0.01), V7 (r = 0.70, p < 0.01), and VO2SUBDP (r = -0.70, p < 0.01). Faster skiers in sprint simulation had a higher absolute VO2 (L.min) (p < 0.05-0.01) during sprint heats, and higher anaerobic skiing power (VMAST, p < 0.05) and better anaerobic skiing economy (V3, V5, V7, p < 0.05-0.001) than slower skiers. Faster skiers were also stronger in BP, with regard to both absolute (p < 0.01) and relative (p < 0.05) values. In addition, anaerobic characteristics seem to be of importance at the beginning of the XC skiing sprint competition, whereas the aerobic characteristics become more important as the XC skiing sprint competition progressed. This study indicates that sprint skiers should emphasize sport-specific upper body training, and training skiing economy at high speeds.

  20. Silk Gland Gene Expression during Larval-Pupal Transition in the Cotton Leaf Roller Sylepta derogata (Lepidoptera: Pyralidae)

    PubMed Central

    Su, Honghua; Cheng, Yuming; Wang, Zhongyang; Li, Zhong; Stanley, David; Yang, Yizhong

    2015-01-01

    The cotton leaf roller, Sylepta derogata, is a silk-producing insect pest. While young larvae feed on the underside of leaves, the older ones roll cotton leaves and feed on the leaf edges, which defoliates cotton plants. The larvae produce silk to stabilize the rolled leaf and to balloon from used to new leaves. Despite the significance of silk in the biology of pest insect species, there is virtually no information on the genes involved in their silk production. This is a substantial knowledge gap because some of these genes may be valuable targets for developing molecular pest management technologies. We addressed the gap by posing the hypothesis that silk gland gene expression changes during the transition from larvae to pupae. We tested our hypothesis using RNA-seq to investigate changes in silk gland gene expression at three developmental stages, 5th instar larvae (silk producing; 15,445,926 clean reads), prepupae (reduced silk producing; 13,758,154) and pupae (beyond silk producing; 16,787,792). We recorded 60,298 unigenes and mapped 50,158 (larvae), 48,415 (prepupae) and 46,623 (pupae) of them to the NCBI database. Most differentially expressed genes in the 5th instar larvae/prepupae libraries were relevant to nucleotide synthesis and maintenance of silk gland function. We identified down-regulated transcriptional factors and several genes involved in silk formation in the three libraries and verified the expression pattern of eight genes by qPCR. The developmental- and tissue-specific expression patterns of the fibroin light chain gene showed it was highly expressed during the larval silk-producing stage. We recorded highest expression of this gene in the larval silk gland, compared to other tissues, including midgut, hindgut, epidermis, Malpighian tubes, hemolymph and fat body. These data are a genetic resource to guide selection of key genes that may be targeted for in planta and other gene-silencing technologies for sustainable cotton agriculture. PMID

  1. Centrifugal pump and roller pump in adult cardiac surgery: a meta-analysis of randomized controlled trials.

    PubMed

    Saczkowski, Richard; Maklin, Michelle; Mesana, Thierry; Boodhwani, Munir; Ruel, Marc

    2012-08-01

    Centrifugal pump (CP) and roller pump (RP) designs are the dominant main arterial pumps used in cardiopulmonary bypass (CPB). Trials reporting clinical outcome measures comparing CP and RP are controversial. Therefore, a meta-analysis was undertaken to evaluate clinical variables from randomized controlled trials (RCTs). Keyword searches were performed on Medline (1966-2011), EmBase (1980-2011), and CINAHL (1981-2011) for studies comparing RP and CP as the main arterial pump in adult CPB. Pooled fixed-effects estimates for dichotomous and continuous data were calculated as an odds ratio and weighted-mean difference, respectively. The P value was utilized to assess statistical significance (P < 0.05) between CP and RP groups. Eighteen RCTs met inclusion criteria, which represented 1868 patients (CP = 961, RP = 907). The prevailing operation was isolated coronary artery bypass graft surgery (CP = 88%, RP = 87%). Fixed-effects pooled estimates were performed for end-of-CPB (ECP) and postoperative day one (PDO) for platelet count (ECP: P = 0.51, PDO: P = 0.16), plasma free hemoglobin (ECP: P = 0.36, PDO: P = 0.24), white blood cell count (ECP: P = 0.21, PDO: P = 0.66), and hematocrit (ECP: P = 0.06, PDO: P = 0.51). No difference was demonstrated for postoperative blood loss (P = 0.65) or red blood cell transfusion (P = 0.71). Intensive care unit length of stay (P = 0.30), hospital length of stay (P = 0.33), and mortality (P = 0.91) were similar between the CP and RP groups. Neurologic outcomes were not amenable to pooled analysis; nevertheless, the results were inconclusive. There was no reported pump-related malfunction or mishap. The meta-analysis of RCTs comparing CP and RP in adult cardiac surgery suggests no significant difference for hematological variables, postoperative blood loss, transfusions, neurological outcomes, or mortality.

  2. Comparison of heart rate deflection and ventilatory threshold during a field cross-country roller-skiing test.

    PubMed

    Fabre, Nicolas; Passelergue, Philippe; Bouvard, Marc; Perrey, Stéphane

    2008-11-01

    This study was to assess whether the point of deflection from linearity of heart rate (HRd) could be an accurate predictor of ventilatory threshold (VT2) during a specific cross-country roller-skiing (RS) test. Ten well-trained cross-country skiers performed a maximal and incremental RS test in the field and a standardized maximal and incremental treadmill running (TR) test in the laboratory. Values of oxygen uptake (VO2) and heart rate (HR) were continuously recorded during all exercises by a portable breath-by-breath gas exchange measurement system and a wireless Polar monitoring system, respectively. The VT2 and HRd points were individually determined by visual analysis during RS. Maximal VO2 (VO2 max) and HR were higher (p < 0.05) during TR (67.1 +/- 7.3 ml x min(-1) x kg(-1) and 196.0 +/- 14.1 bpm, respectively) compared with RS (64.2 +/- 7.3 ml x min(-1) x kg(-1) and 191.5 +/- 13.1 bpm, respectively). However, a high correlation (r = 0.94, p < 0.01) between TR and VO2 max was observed. Paired t-tests showed no significant differences in HR (183.6 +/- 15.1 vs. 185.2 +/- 13.9 bpm) and VO2 (55.5 +/- 7.1 vs. 55.8 +/- 6.1 ml x min(-1) x kg(-1)) at intensities corresponding to HRd and VT2 during the RS test, respectively; Pearson product-moment correlation coefficients demonstrated significant relationships for HR at the HRd and VT2 points (r = 0.99, p < 0.001) as well as for VO2 (r = 0.95, p < 0.001). Our results indicate that the specific incremental RS test is effective in eliciting HRd in the field for all skiers and is an accurate predictor of VT2. These findings give very interesting practical applications to cross-country coaches and skiers to evaluate and control specific aerobic training loads.

  3. Anodized Steel Electrodes for Supercapacitors.

    PubMed

    Sagu, Jagdeep S; Wijayantha, K G Upul; Bohm, Mallika; Bohm, Siva; Kumar Rout, Tapan

    2016-03-01

    Steel was anodized in 10 M NaOH to enhance its surface texture and internal surface area for application as an electrode in supercapacitors. A mechanism was proposed for the anodization process. Field-emission gun scanning electron microscopy (FEGSEM) studies of anodized steel revealed that it contains a highly porous sponge like structure ideal for supercapacitor electrodes. X-ray photoelectron spectroscopy (XPS) measurements showed that the surface of the anodized steel was Fe2O3, whereas X-ray diffraction (XRD) measurements indicated that the bulk remained as metallic Fe. The supercapacitor performance of the anodized steel was tested in 1 M NaOH and a capacitance of 18 mF cm(-2) was obtained. Cyclic voltammetry measurements showed that there was a large psueudocapacitive contribution which was due to oxidation of Fe to Fe(OH)2 and then further oxidation to FeOOH, and the respective reduction of these species back to metallic Fe. These redox processes were found to be remarkably reversible as the electrode showed no loss in capacitance after 10000 cycles. The results demonstrate that anodization of steel is a suitable method to produce high-surface-area electrodes for supercapacitors with excellent cycling lifetime. PMID:26891093

  4. Anodized Steel Electrodes for Supercapacitors.

    PubMed

    Sagu, Jagdeep S; Wijayantha, K G Upul; Bohm, Mallika; Bohm, Siva; Kumar Rout, Tapan

    2016-03-01

    Steel was anodized in 10 M NaOH to enhance its surface texture and internal surface area for application as an electrode in supercapacitors. A mechanism was proposed for the anodization process. Field-emission gun scanning electron microscopy (FEGSEM) studies of anodized steel revealed that it contains a highly porous sponge like structure ideal for supercapacitor electrodes. X-ray photoelectron spectroscopy (XPS) measurements showed that the surface of the anodized steel was Fe2O3, whereas X-ray diffraction (XRD) measurements indicated that the bulk remained as metallic Fe. The supercapacitor performance of the anodized steel was tested in 1 M NaOH and a capacitance of 18 mF cm(-2) was obtained. Cyclic voltammetry measurements showed that there was a large psueudocapacitive contribution which was due to oxidation of Fe to Fe(OH)2 and then further oxidation to FeOOH, and the respective reduction of these species back to metallic Fe. These redox processes were found to be remarkably reversible as the electrode showed no loss in capacitance after 10000 cycles. The results demonstrate that anodization of steel is a suitable method to produce high-surface-area electrodes for supercapacitors with excellent cycling lifetime.

  5. Influence of ambient moisture on the compaction behavior of microcrystalline cellulose powder undergoing uni-axial compression and roller-compaction: a comparative study using near-infrared spectroscopy.

    PubMed

    Gupta, Abhay; Peck, Garnet E; Miller, Ronald W; Morris, Kenneth R

    2005-10-01

    This study evaluates the effect of variation in the ambient moisture on the compaction behavior of microcrystalline cellulose (MCC) powder. The study was conducted by comparing the physico-mechanical properties of, and the near infrared (NIR) spectra collected on, compacts prepared by roller compaction with those collected on simulated ribbons, that is, compacts prepared under uni-axial compression. Relative density, moisture content, tensile strength (TS), and Young modulus were used as key sample attributes for comparison. Samples prepared at constant roller compactor settings and feed mass showed constant density and a decrease in TS with increasing moisture content. Compacts prepared under uni-axial compression at constant pressure and compact mass showed the opposite effect, that is, density increased while TS remained almost constant with increasing moisture content. This suggests difference in the influence of moisture on the material under roller compaction, in which the roll gap (i.e., thickness and therefore density) remains almost constant, vs. under uni-axial compression, in which the thickness is free to change in response to the applied pressure. Key sample attributes were also related to the NIR spectra using multivariate data analysis by the partial least squares projection to latent structures (PLS). Good agreement was observed between the measured and the NIR-PLS predicted values for all key attributes for both, the roller compacted samples as well as the simulated ribbons.

  6. High-temperature brazing of stainless steel

    NASA Technical Reports Server (NTRS)

    Beuyukian, C. S.; Heisman, R. M.; Mitchell, M. J.

    1978-01-01

    Prevention of iron contamination of platens is eliminated by placing alumina/silica ceramic-fiber blankets between platens and carbon-steel plate. Carbon-steel plates provide rigidity and improve heat transfer.

  7. Steel erected at A-3 Test Stand

    NASA Technical Reports Server (NTRS)

    2008-01-01

    Workers erect the first fabricated steel girders to arrive at the A-3 Test Stand at Stennis Space Center. Steel work began at the construction site Oct. 29 and is scheduled to continue into next spring.

  8. Corrosion control of steel-reinforced concrete

    NASA Astrophysics Data System (ADS)

    Chung, D. D. L.

    2000-10-01

    The methods and materials for corrosion control of steel-reinforced concrete are reviewed. The methods are steel surface treatment, the use of admixtures in concrete, surface coating on concrete, and cathodic protection.

  9. ESF GROUND SUPPORT - STRUCTURAL STEEL ANALYSIS

    SciTech Connect

    T. Misiak

    1996-06-26

    The purpose and objective of this analysis are to expand the level of detail and confirm member sizes for steel sets included in the Ground Support Design Analysis, Reference 5.20. This analysis also provides bounding values and details and defines critical design attributes for alternative configurations of the steel set. One possible configuration for the steel set is presented. This analysis covers the steel set design for the Exploratory Studies Facility (ESF) entire Main Loop 25-foot diameter tunnel.

  10. Steel erected at A-3 Test Stand

    NASA Technical Reports Server (NTRS)

    2008-01-01

    Fabricated steel began arriving by truck Oct. 24 for construction of the A-3 Test Stand that will be used to test the engine for the nation's next generation of moon rockets. Within days workers from Lafayette Steel Erector Inc. began assembling the 16 steel stages needed on the foundation and footings poured in the previous year.

  11. Steeling and Resilience in Art Education

    ERIC Educational Resources Information Center

    Heise, Donalyn

    2014-01-01

    Steel is an incredibly strong alloy of iron and carbon. Due to its incredible strength and durability, this resilient material is commonly used for constructing buildings. The transitive verb "steeling" is defined in Miriam-Webster dictionary as "to fill with resolution or determination, as in, she 'steeled herself to face the…

  12. Metallography of maraging 350 steel

    SciTech Connect

    Hutson, S.M.; Merten, C.W.

    1987-01-01

    A technique for etching maraging 350 steel with Glyceregia is described. Surface activation procedures are integral to this technique. Microstructural features revealed by this technique are compared with those obtained with Kalling's reagent, Fry's reagent, and 5% Nital, three etchants commonly used to reveal microstructures of maraging steels. Features which may be simultaneously revealed using Glyceregia include prior austenite grain boundaries, martensitic structure, precipitates, titanium carbo-nitrides, and reverted austenite. The other etchants examined in this investigation typically reveal only a few of the microstructural features detailed above at any one time. 11 refs., 10 figs., 2 tabs.

  13. Teaching Steel Connections Using an Interactive Virtual Steel Sculpture

    ERIC Educational Resources Information Center

    Moaveni, Saeed; Chou, Karen C.

    2015-01-01

    Steel connections play important roles in the integrity of a structure, and many structural failures are attributed to connection failures. Connections are the glue that holds a structure together. The failures of the Hartford Coliseum in 1977, the Hyatt Regency Hotel in Kansas City in 1980, and the I-35W Bridge in Minneapolis in 2007 are all…

  14. Closure Report for Corrective Action Unit 404: Roller Coaster Sewage Lagoons and North Disposal Trench, Tonopah Test Range, Nevada with ROTC 1, Revision 0

    SciTech Connect

    Lynn Kidman

    1998-09-01

    This Closure Report provides the documentation for closure of the Roller Coaster Sewage Lagoons and North Disposal Trench Comective Action Unit (CAU) 404. CAU 404 consists of the Roller Coaster Sewage Lagoons (Corrective Action Site [CAS] TA-03-O01-TA-RC) and the North Disposal Trench (CAS TA-21-001-TA-RC). The site is located on the Tonopah Test Range, approximately 225 kilometers (km) (140 miles [mi]) northwest ofLas Vegas, Nevada. . The sewage lagoons received ~quid sanitary waste horn the Operation Roller Coaster Man Camp in 1963 and debris from subsequent range and construction cleanup activities. The debris and ordnance was subsequently removed and properly dispos~, however, pesticides were detected in soil samples born the bottom of the lagoons above the U,S. Environmental Protection Agency Region IX Prelimimuy Remediation Goals (EPA 1996). . The North Disposal Trench was excavated in 1963. Debris from the man camp and subsequent range and construction cleanup activities was placed in the trench. Investigation results indicated that no constituents of concern were detected in soil samples collected from the trench. Remedial alternative proposed in the Comctive Action Decision Document (CADD) fm the site was “Covering” (DOE, 1997a). The Nevada Division of”Enviromnental Protection (NDEP)-approved Correction Action Plan (CAP) proposed the “Covering” niethodology (1997b). The closure activities were completed in accorhce with the approwil CAP and consisted of baclctllling the sewage lagoons and disposal trench, constructing/planting an engineered/vegetative cover in the area of the sewage lagoons and dikposal trencQ installing a perimeter fence and signs, implementing restrictions on fi~e use, and preparing a Post-Closure Monitoring Plan. “ Since closure activities. for CAU 404 have been completed in accordance with the Nevada Division of Environmental Protection-approved CAP (DOE, 1997b) as documented in this Closure Report, the U.S. Department of

  15. A Mathematical Roller Derby.

    ERIC Educational Resources Information Center

    Drucker, Daniel

    1992-01-01

    Describes an experiment to determine which of four objects, hollow cylinders, solid cylinders, hollow balls, and solid balls, will reach the bottom of an inclined plane first when released simultaneously. Provides solutions to the problem and supplementary exercises. (MDH)

  16. Taming the Roller Coaster.

    PubMed

    Linden, Todd

    2016-01-01

    The Rural Health Care Leadership Conference offers the chance for executives and board members to network and gain insights from each other and expert presenters. And there's a bonus: It's in Phoenix in February. PMID:27509635

  17. Roller Coaster Math.

    ERIC Educational Resources Information Center

    Pritchard, Arvilla

    1992-01-01

    Presents number loop pattern activities and games designed to interest elementary students in mathematics and encourage computational skills. The activities work as games and cooperative activities and invite math exploration. (SM)

  18. The Therapeutic Roller Coaster

    PubMed Central

    CHU, JAMES A.

    1992-01-01

    Survivors of severe childhood abuse often encounter profound difficulties. In addition to posttraumatic and dissociative symptomatology, abuse survivors frequently have characterologic problems, particularly regarding self-care and maintaining relationships. Backgrounds of abuse, abandonment, and betrayal are often recapitulated and reenacted in therapy, making the therapeutic experience arduous and confusing for therapists and patients. Efforts must be directed at building an adequate psychotherapeutic foundation before undertaking exploration and abreaction of past traumatic experiences. This discussion sets out a model for treatment of childhood abuse survivors, describing stages of treatment and suggesting interventions. Common treatment dilemmas or "traps" are discussed, with recommendations for their resolution. PMID:22700116

  19. Superhard Nanocrystalline Homometallic Stainless Steel on Steel for Seamless Coatings

    NASA Technical Reports Server (NTRS)

    Tobin, Eric J.; Hafley, R. (Technical Monitor)

    2002-01-01

    The objective of this work is to deposit nanocrystalline stainless steel onto steel substrates (homometallic) for enhanced wear and corrosion resistance. Homometallic coatings provide superior adhesion, and it has been shown that ultrafine-grained materials exhibit the increased hardness and decreased permeability desired for protective coatings. Nanocrystals will be produced by controlling nucleation and growth and use of an ion beam during deposition by e-beam evaporation or sputtering. Phase I is depositing 31 6L nanocrystalline stainless steel onto 31 6L stainless steel substrates. These coatings exhibit hardnesses comparable to those normally obtained for ceramic coatings such ZrO2, and possess the superior adhesion of seamless, homometallic coatings. Hardening the surface with a similar material also enhances adhesion, by avoiding problems associated with thermal and lattice mismatch. So far we have deposited nanocrystalline homometallic 316L stainless steel coatings by varying the ions and the current density of the ion beams. For all deposition conditions we have produced smooth, uniform, superhard coatings. All coatings exhibit hardness of at least 200% harder than that of bulk materials. Our measurements indicate that there is a direct relationship between nanohardness and the current density of the ion beam. Stress measurements indicate that stress in the films is increasingly proportional to current density of the ion beam. TEM, XPS, and XRD results indicate that the coated layers consist of FCC structure nanocrystallites with a dimension of about 10 to 20 nm. The Ni and Mo concentration of these coating are lower than those of bulk 316L but the concentration of Cr is higher.

  20. Preformed posterior stainless steel crowns: an update.

    PubMed

    Croll, T P

    1999-02-01

    For almost 50 years, dentists have used stainless steel crowns for primary and permanent posterior teeth. No other type of restoration offers the convenience, low cost, durability, and reliability of such crowns when interim full-coronal coverage is required. Preformed stainless steel crowns have improved over the years. Better luting cements have been developed and different methods of crown manipulation have evolved. This article reviews stainless steel crown procedures for primary and permanent posterior teeth. Step-by-step placement of a primary molar stainless steel crown is documented and permanent molar stainless steel crown restoration is described. A method for repairing a worn-through crown also is reviewed.

  1. Advanced sheet steels for automotive applications

    NASA Astrophysics Data System (ADS)

    Fekete, James R.; Strugala, Donald C.; Yao, Zhicong

    1992-01-01

    Vacuum degassing has recently been used by sheet steel producers to improve their products' ductility and strength. Carbon contents can be reduced by an order of magnitude to less than 0.0030 wt.%. Through careful alloying and processing, a range of new steel products has been developed for the automotive industry. These products include interstitial-free, deep-drawing-quality steels; formable, high-strength, interstitial-free steels; and bake-hardenable steels. This article summarizes the chemistry and processing needed to produce these products.

  2. Imaging molten steel flow profiles

    NASA Astrophysics Data System (ADS)

    Binns, R.; Lyons, A. R. A.; Peyton, A. J.; Pritchard, W. D. N.

    2001-08-01

    Control of delivery of molten steel in continuous casting is critical in order to ensure stability of the meniscus and satisfactory mould flow patterns, which in turn are determinants of cleanness and surface quality of steel. Considerable effort has been expended over the last ten years on optimizing the design of the metal delivery system, particularly the pouring nozzle, in order to allow the consistent production of high quality steel at a high throughput. This paper looks forward to possible systems that are capable of tomographically imaging the distribution of molten steel flows in these applications. The paper will concentrate on the feasibility of using electromagnetic methods. The paper will present some initial results; an overview of the applied image reconstruction process will also be included. The paper will conclude with a discussion of possible future developments, such as the use of a tomographic or multi-frequency approach, future research on the reconstruction image procedures and the potential for visualization and flow measurement. There is a need for further research in this area and some priority areas for future work will be suggested.

  3. Precision machining of steel decahedrons

    NASA Technical Reports Server (NTRS)

    Abernathy, W. J.; Sealy, J. R.

    1972-01-01

    Production of highly accurate decahedron prisms from hardened stainless steel is discussed. Prism is used to check angular alignment of mounting pads of strapdown inertial guidance system. Accuracies obtainable using recommended process and details of operation are described. Photographic illustration of production device is included.

  4. 60 Years of duplex stainless steel applications

    SciTech Connect

    Olsson, J.; Liljas, M.

    1994-12-31

    In this paper the history of wrought duplex stainless steel development and applications is described. Ferritic-austenitic stainless steels were introduced only a few decades after stainless steels were developed. The paper gives details from the first duplex stainless steels in the 1930`s to the super duplex stainless steel development during the 1980`s. During the years much effort has been devoted to production and welding metallurgy as well as corrosion research of the duplex stainless steels. Therefore, duplex stainless steels are to-day established in a wide product range. Numerous important applications are exemplified. In most cases the selection of a duplex steel has been a result of the combination high strength excellent corrosion resistance. In the pulp and paper industry the most interesting use is as vessel material in digesters. For chemical process industry, the duplex steels are currently used in heat exchangers. The largest application of duplex steels exists in the oil and gas/offshore industry. Hundreds of kms of pipelines are installed and are still being installed. An increased use of duplex steels is foreseen in areas where the strength is of prime importance.

  5. STEFINS: a steel freezing integral simulation program

    SciTech Connect

    Frank, M.V.

    1980-09-01

    STEFINS (STEel Freezing INtegral Simulation) is a computer program for the calculation of the rate of solidification of molten steel on solid steel. Such computations arize when investigating core melt accidents in fast reactors. In principle this problem involves a coupled two-dimensional thermal and hydraulic approach. However, by physically reasonable assumptions a decoupled approach has been developed. The transient solidification of molten steel on a cold wall is solved in the direction normal to the molten steel flow and independent from the solution for the molten steel temperature and Nusselt number along the direction of flow. The solutions to the applicable energy equations have been programmed in cylindrical and slab geometries. Internal gamma heating of steel is included.

  6. Post-Closure Inspection Report for Corrective Action Unit 404: Roller Coaster Sewage Lagoons and North Disposal Trench Tonopah Test Range, Nevada, Calendar Year 2000

    SciTech Connect

    K. B. Campbell

    2001-06-01

    Post-closure monitoring requirements for the Roller Coaster Sewage Lagoons and North Disposal Trench (Corrective Action Unit [CAW 404]) (Figure 1) are described in Closure Report for Corrective Action Unit 404, Roller Coaster Sewage Lagoons and North Disposal Trench, Tonopah Test Range, Nevada, report number DOE/NV--187. The Closure Report (CR) was submitted to the Nevada Division of Environmental Protection (NDEP) on September 11, 1998. Permeability results of soils adjacent to the engineered cover and a request for closure of CAU 404 were transmitted to the NDEP on April 29, 1999. The CR (containing the Post-Closure Monitoring Plan) was approved by the NDEP on May 18, 1999. Post-closure monitoring at CAU 404 consists of the following: (1) Site inspections done twice a year to evaluate the condition of the unit; (2) Verification that the site is secure; (3) Notice of any subsidence or deficiencies that may compromise the integrity of the unit; (4) Remedy of any deficiencies within 90 days of discovery; and (5) Preparation and submittal of an annual report. Site inspections were conducted on June 19, 2000, and November 21, 2000. The site inspections were conducted after completion of the revegetation activities (October 30, 1997) and NDEP approval of the CR (May 18, 1999). All site inspections were conducted in accordance with the Post-Closure Monitoring Plan in the NDEP-approved CR. This report includes copies of inspection checklists, photographs, recommendations, and conclusions. The Post-Closure Inspection Checklists are found in Attachment A, a copy of the field notes is found in Attachment B, and copies of the inspection photographs are found in Attachment C.

  7. Comparative Structural Strength Research of Hardened Carbon Steel and Hot-Rolled Alloy Steel

    NASA Astrophysics Data System (ADS)

    Bogomolov, A. V.; Zhakupov, A. N.; Kanayev, A. T.; Sikach, I. A.; Tugumov, K. K.

    2016-08-01

    Experiments on quantitative evaluation of fatigue strength showed that St5ps and St5sp carbon steels with A400 strength class can be fully applied for erection of constructions and buildings having cyclical loads during operation. Study of corrosion resistance of hardened carbon steel in comparison with hot-rolled alloy steel consists in difference in structures and hence, difference in intensity of electric and chemical processes featuring presence of steel in concrete. Structure of St5sp steel with A400 strength class in surface area has significantly less corrosion rate than ferritic-perlitic structure of 35GS steel with A400 strength class.

  8. Steel project fact sheet: Steel reheating for further processing

    SciTech Connect

    1998-04-01

    Steel reheating is an energy-intensive process requiring uniform temperature distribution within reheating furnaces. Historically, recuperators have ben used to preheat combustion air, thereby conserving energy. More recent innovations include oxygen enrichment and the use of regenerative burners, which provide higher preheat air temperatures than recuperators. These processes have limitations such as equipment deterioration, decreasing energy efficiency over time, high maintenance costs, and increased NO{sub x} emissions with increased air preheat temperature, unless special equipment is used. Praxair, Inc., supplier of oxygen and other industrial gases to the steel industry, proposes to introduce an innovative oxy-fuel burner technology (using 100% oxygen) to the steel reheating industry. Oxy-fuel combustion reduces or eliminates nitrogen in combustion air and substantially reduces waste heat carried out with flue gas. Based on technology currently used in the glass, hazardous waste, and aluminum industries, Praxair has developed and patented low temperature, oxy-fuel burners that can be used in high temperature industrial furnaces where temperature uniformity is critical and extremely low NO{sub x} emissions are desired. The technical goal of the project is to demonstrate the use of oxy-fuel burners in a slab reheat furnace while reducing energy consumption by 45% and NO{sub x} emissions by 90% within the converted furnace zones. Successful implementation of this technology also will eliminate the need to periodically replace recuperators and install NO{sub x} removal equipment.

  9. Bond characteristics of steel fiber and deformed reinforcing steel bar embedded in steel fiber reinforced self-compacting concrete (SFRSCC)

    NASA Astrophysics Data System (ADS)

    Aslani, Farhad; Nejadi, Shami

    2012-09-01

    Steel fiber reinforced self-compacting concrete (SFRSCC) is a relatively new composite material which congregates the benefits of the self-compacting concrete (SCC) technology with the profits derived from the fiber addition to a brittle cementitious matrix. Steel fibers improve many of the properties of SCC elements including tensile strength, ductility, toughness, energy absorption capacity, fracture toughness and cracking. Although the available research regarding the influence of steel fibers on the properties of SFRSCC is limited, this paper investigates the bond characteristics between steel fiber and SCC firstly. Based on the available experimental results, the current analytical steel fiber pullout model (Dubey 1999) is modified by considering the different SCC properties and different fiber types (smooth, hooked) and inclination. In order to take into account the effect of fiber inclination in the pullout model, apparent shear strengths ( τ ( app)) and slip coefficient ( β) are incorporated to express the variation of pullout peak load and the augmentation of peak slip as the inclined angle increases. These variables are expressed as functions of the inclined angle ( ϕ). Furthurmore, steel-concrete composite floors, reinforced concrete floors supported by columns or walls and floors on an elastic foundations belong to the category of structural elements in which the conventional steel reinforcement can be partially replaced by the use of steel fibers. When discussing deformation capacity of structural elements or civil engineering structures manufactured using SFRSCC, one must be able to describe thoroughly both the behavior of the concrete matrix reinforced with steel fibers and the interaction between this composite matrix and discrete steel reinforcement of the conventional type. However, even though the knowledge on bond behavior is essential for evaluating the overall behavior of structural components containing reinforcement and steel fibers

  10. Bond characteristics of steel fiber and deformed reinforcing steel bar embedded in steel fiber reinforced self-compacting concrete (SFRSCC)

    NASA Astrophysics Data System (ADS)

    Aslani, Farhad; Nejadi, Shami

    2012-09-01

    Steel fiber reinforced self-compacting concrete (SFRSCC) is a relatively new composite material which congregates the benefits of the self-compacting concrete (SCC) technology with the profits derived from the fiber addition to a brittle cementitious matrix. Steel fibers improve many of the properties of SCC elements including tensile strength, ductility, toughness, energy absorption capacity, fracture toughness and cracking. Although the available research regarding the influence of steel fibers on the properties of SFRSCC is limited, this paper investigates the bond characteristics between steel fiber and SCC firstly. Based on the available experimental results, the current analytical steel fiber pullout model (Dubey 1999) is modified by considering the different SCC properties and different fiber types (smooth, hooked) and inclination. In order to take into account the effect of fiber inclination in the pullout model, apparent shear strengths (τ (app)) and slip coefficient (β) are incorporated to express the variation of pullout peak load and the augmentation of peak slip as the inclined angle increases. These variables are expressed as functions of the inclined angle (ϕ). Furthurmore, steel-concrete composite floors, reinforced concrete floors supported by columns or walls and floors on an elastic foundations belong to the category of structural elements in which the conventional steel reinforcement can be partially replaced by the use of steel fibers. When discussing deformation capacity of structural elements or civil engineering structures manufactured using SFRSCC, one must be able to describe thoroughly both the behavior of the concrete matrix reinforced with steel fibers and the interaction between this composite matrix and discrete steel reinforcement of the conventional type. However, even though the knowledge on bond behavior is essential for evaluating the overall behavior of structural components containing reinforcement and steel fibers

  11. A mortality study among mild steel and stainless steel welders.

    PubMed

    Moulin, J J; Wild, P; Haguenoer, J M; Faucon, D; De Gaudemaris, R; Mur, J M; Mereau, M; Gary, Y; Toamain, J P; Birembaut, Y

    1993-03-01

    A mortality study was carried out in conjunction with the European mortality study among welders coordinated by the International Agency for Research on Cancer (IARC). The study was aimed at assessing risks for lung cancer in relation to exposure to asbestos, welding fumes containing chromium and nickel, and tobacco smoke. The study included a cohort of 2721 welders and an internal comparison group of 6683 manual workers employed in 13 factories in France. The mortality of the two cohorts was studied from 1975 to 1988 by the historical prospective method. Job histories of welders were traced including welding processes used, metals welded, and proportion of worktime spent in welding. Data on smoking habits were collected from medical records. The observed number of deaths were compared with those expected (standardised mortality ratio (SMR)) based on national rates with adjustments for age, sex, and calendar time. The smoking habits of 87% of the whole study population were known. The distribution of welders and controls according to smoking was not statistically different. The overall mortality was slightly higher for welders (SMR = 1.02, 95% confidence interval (95% CI) 0.89-1.18) than for controls (SMR = 0.91, 95% CI 0.84-0.99). For lung cancer, the SMR was 1.24 (95% CI 0.75-1.94) for welders, whereas the corresponding value was lower for controls (SMR = 0.94, 95% CI 0.68-1.26). The SMR for lung cancer was 1.59 among non-shipyard mild steel welders (95% CI 0.73-3.02). This contrasted with the results for all stainless steel welders (SMR = 0.92, 95% CI 0.19-2.69), and for stainless steel welders predominantly exposed to chromium VI (SMR = 1.03, 95% CI 0.12-3.71). Moreover, SMRs for lung cancer for mild steel welders tended to increase with duration of exposure and time since first exposure, leading to significant excesses for duration > or = 20 years and latency > or = 20 years. Such a pattern was not found for stainless steel welders.

  12. A mortality study among mild steel and stainless steel welders.

    PubMed Central

    Moulin, J J; Wild, P; Haguenoer, J M; Faucon, D; De Gaudemaris, R; Mur, J M; Mereau, M; Gary, Y; Toamain, J P; Birembaut, Y

    1993-01-01

    A mortality study was carried out in conjunction with the European mortality study among welders coordinated by the International Agency for Research on Cancer (IARC). The study was aimed at assessing risks for lung cancer in relation to exposure to asbestos, welding fumes containing chromium and nickel, and tobacco smoke. The study included a cohort of 2721 welders and an internal comparison group of 6683 manual workers employed in 13 factories in France. The mortality of the two cohorts was studied from 1975 to 1988 by the historical prospective method. Job histories of welders were traced including welding processes used, metals welded, and proportion of worktime spent in welding. Data on smoking habits were collected from medical records. The observed number of deaths were compared with those expected (standardised mortality ratio (SMR)) based on national rates with adjustments for age, sex, and calendar time. The smoking habits of 87% of the whole study population were known. The distribution of welders and controls according to smoking was not statistically different. The overall mortality was slightly higher for welders (SMR = 1.02, 95% confidence interval (95% CI) 0.89-1.18) than for controls (SMR = 0.91, 95% CI 0.84-0.99). For lung cancer, the SMR was 1.24 (95% CI 0.75-1.94) for welders, whereas the corresponding value was lower for controls (SMR = 0.94, 95% CI 0.68-1.26). The SMR for lung cancer was 1.59 among non-shipyard mild steel welders (95% CI 0.73-3.02). This contrasted with the results for all stainless steel welders (SMR = 0.92, 95% CI 0.19-2.69), and for stainless steel welders predominantly exposed to chromium VI (SMR = 1.03, 95% CI 0.12-3.71). Moreover, SMRs for lung cancer for mild steel welders tended to increase with duration of exposure and time since first exposure, leading to significant excesses for duration > or = 20 years and latency > or = 20 years. Such a pattern was not found for stainless steel welders. PMID:8457490

  13. Longer Life for Steel Structures

    NASA Technical Reports Server (NTRS)

    1990-01-01

    IC 531 is a coating manufactured and marketed by Inorganic Coatings, Inc. The coating was developed by Goddard to protect structures at Kennedy Space Center. It is a high ratio potassium silicate formula. The coating is water based, nontoxic, and nonflammable. It generates no volatile organic compounds nor hazardous chemical waste, and bonds to steel in 30 minutes. At the present time, no one can say for sure how long IC 531's effective lifetime is. Some of the original Goddard test applications of 1976 are still going strong after lengthy exposure to the Sun, salt and moisture. Says IC in company literature: 'IC 531 offers virtually permanent protection for steel. We predict it will protect structures for well beyond 25 years. If necessary, it is infinitely maintainable; if damaged, it can easily be touched up with more IC 531.'

  14. Steel Industry Energy Bandwidth Study

    SciTech Connect

    none,

    2004-10-01

    ITP conducted a study on energy use and potential savings, or "bandwidth" study, in major steelmaking processes. Intended to provide a realistic estimate of the potential amount of energy that can be saved in an industrial process, the "bandwidth" refers to the difference between the amount of energy that would be consumed in a process using commercially available technology versus the minimum amount of energy needed to achieve those same results based on the 2nd law of thermodynamics. The Steel Industry Energy Bandwidth Study (PDF 133 KB) also estimates steel industry energy use in the year 2010, and uses that value as a basis for comparison against the minimum requirements. This energy savings opportunity for 2010 will aid focus on longer term R&D.

  15. Light microscopy of carbon steels

    SciTech Connect

    Samuels, L.E.

    1998-12-31

    Containing over 1,200 representative micrographs and the information and explanatory text that makes them really useful: composition, condition, etchant, and magnification, and more than 100 graphs and tables, this how to book not only gives everyday working examples, but also discusses the relationship between the constitution, metallurgy, and microstructure of various carbon steel products. Written by a renowned expert in metallography, this definitive work is a must for all those working in this area. Contents include: nomenclature of phases and constituents; phase transformations; low-carbon irons and steels; annealing and normalizing; spheroidization and graphitization; austenitization; transformation of austenite; tempering of martensite; welding; surface oxidation, decarburation; and oxidation scaling; glossary of terms; etching methods; conversion tables.

  16. Welding of high chromium steels

    NASA Technical Reports Server (NTRS)

    Miller, W B

    1928-01-01

    A brief description is given of different groups of high chromium steels (rustless iron and stainless steels) according to their composition and more generally accepted names. The welding procedure for a given group will be much the same regardless of the slight variations in chemical composition which may exist within a certain group. Information is given for the tensile properties (yield point and ultimate strength) of metal sheets and welds before and after annealing on coupons one and one-half inches wide. Since welds in rustless iron containing 16 to 18 percent chromium and 7 to 12 percent nickel show the best combination of strength and ductility in the 'as welded' or annealed condition, it is considered the best alloy to use for welded construction.

  17. Shock Hugoniot of 1215 steel

    NASA Astrophysics Data System (ADS)

    Brar, N. S.; Rosenberg, Z.

    1996-05-01

    1215 steel is almost pure iron with 0.1 percent or less carbon. Information pertaining to deformation of this material under shock loading is useful to simulate penetration of projectiles of different shapes, such as fragments or rods, in propellants storage containments made from almost pure iron. In this paper we present the dynamic response of 1215 steel to shock wave loading to 30 GPa. Manganin gauges were used to record the stress wave profiles in these experiments. The Hugoniot data in the stress-particle velocity plane was obtained to 30 GPa. Hugoniot elastic limit was found to be 1.37±0.05 GPa. Phase transformation (α-ɛ) takes place at about 13.2±0.2 GPa, which agrees with the value determined by Barker and Hollenbach using VISAR. Hugoniot does not show any softening at stresses below 13 GPa.

  18. Steel Industry Marginal Opportunity Analysis

    SciTech Connect

    none,

    2005-09-01

    The Steel Industry Marginal Opportunity Analysis (PDF 347 KB) identifies opportunities for developing advanced technologies and estimates both the necessary funding and the potential payoff. This analysis determines what portion of the energy bandwidth can be captured through the adoption of state-of-the-art technology and practices. R&D opportunities for addressing the remainder of the bandwidth are characterized and plotted on a marginal opportunity curve.

  19. A study of Damascus steel

    SciTech Connect

    Berge, P.

    1995-02-16

    The Damascus sword has been an article of fascination for many years to blade collectors and metallurgists alike. The blades were given their name by Europeans who encountered these blades which originated from Damascus, Syria. They are best known for the appearance of the blade face. Genuine Damascus blades show swirling patterns of alternating light and dark regions which are due to the microstructure of the steel. The microstructure consists of arrays of well rounded cementite patterns in a matrix of either pearlite, bainite, or martensite. When this structure is etched the matrix will turn dark leaving the cementite particles light. Although many blades were produced over the centuries, while some of the process is known the making of a genuine Damascus blade today is generally considered a lost art. Many scientists have studied the subject in an attempt to understand the complex process by which the clustered arrays of cementite particles develop in the steel blades. The most prominent theories to date are presented in the General Introduction to this thesis. The thesis is divided into four main parts. In the first part, four proposed mechanisms of cementite cluster sheet formation as they relate to the banding theory are introduced. Experiments to investigate these mechanisms are presented. In Part II, collaborative research focused on the methodology of the reconstructed process for making Damascus steel is presented. In the third part, a study into the graphitization of the reconstructed blades is presented. In Part IV, experimental attempts at producing Damascus steel ingots in the laboratory are presented.

  20. Steel Collet For Welding Electrodes

    NASA Technical Reports Server (NTRS)

    Gilbert, Jeffrey L.; Gutow, David A.; Burley, Richard K.; Fogul, Irving

    1992-01-01

    Improved steel collet holds electrode for tungsten inert-gas welding but allows quick and easy replacement. Also ensures reliable arc starting. Slip-on compression ring compresses tapered section of body of collet around inner end of welding electrode. Collet mounted in receptacle below stack of lenses and filters in coaxial-vision welding torch. Blind hole in collet protects outermost lens from damage by electrode.

  1. Nano-composite stainless steel

    DOEpatents

    Dehoff, Ryan R.; Blue, Craig A.; Peter, William H.; Chen, Wei; Aprigliano, Louis F.

    2015-07-14

    A composite stainless steel composition is composed essentially of, in terms of wt. % ranges: 25 to 28 Cr; 11 to 13 Ni; 7 to 8 W; 3.5 to 4 Mo; 3 to 3.5 B; 2 to 2.5 Mn; 1 to 1.5 Si; 0.3 to 1.7 C; up to 2 O; balance Fe. The composition has an austenitic matrix phase and a particulate, crystalline dispersed phase.

  2. Nickel: makes stainless steel strong

    USGS Publications Warehouse

    Boland, Maeve A.

    2012-01-01

    Nickel is a silvery-white metal that is used mainly to make stainless steel and other alloys stronger and better able to withstand extreme temperatures and corrosive environments. Nickel was first identified as a unique element in 1751 by Baron Axel Fredrik Cronstedt, a Swedish mineralogist and chemist. He originally called the element kupfernickel because it was found in rock that looked like copper (kupfer) ore and because miners thought that "bad spirits" (nickel) in the rock were making it difficult for them to extract copper from it. Approximately 80 percent of the primary (not recycled) nickel consumed in the United States in 2011 was used in alloys, such as stainless steel and superalloys. Because nickel increases an alloy's resistance to corrosion and its ability to withstand extreme temperatures, equipment and parts made of nickel-bearing alloys are often used in harsh environments, such as those in chemical plants, petroleum refineries, jet engines, power generation facilities, and offshore installations. Medical equipment, cookware, and cutlery are often made of stainless steel because it is easy to clean and sterilize. All U.S. circulating coins except the penny are made of alloys that contain nickel. Nickel alloys are increasingly being used in making rechargeable batteries for portable computers, power tools, and hybrid and electric vehicles. Nickel is also plated onto such items as bathroom fixtures to reduce corrosion and provide an attractive finish.

  3. Utilization of structural steel in buildings.

    PubMed

    Moynihan, Muiris C; Allwood, Julian M

    2014-08-01

    Over one-quarter of steel produced annually is used in the construction of buildings. Making this steel causes carbon dioxide emissions, which climate change experts recommend be reduced by half in the next 37 years. One option to achieve this is to design and build more efficiently, still delivering the same service from buildings but using less steel to do so. To estimate how much steel could be saved from this option, 23 steel-framed building designs are studied, sourced from leading UK engineering firms. The utilization of each beam is found and buildings are analysed to find patterns. The results for over 10 000 beams show that average utilization is below 50% of their capacity. The primary reason for this low value is 'rationalization'-providing extra material to reduce labour costs. By designing for minimum material rather than minimum cost, steel use in buildings could be drastically reduced, leading to an equivalent reduction in 'embodied' carbon emissions.

  4. A Method for Imaging Steel Bars Behind a Ferrous Steel Boundary

    NASA Astrophysics Data System (ADS)

    Fernandes, B.; Miller, G.; Zaid, M.; Gaydecki, P.

    2006-03-01

    A system for detecting steel objects behind ferrous steel boundaries is described. It may be used to image steel reinforcing bars in concrete, where a steel sheet exists between the bars and the surface. The sensor comprises a transmitter, receiver and a dummy coil, which cancels cross-talk and enhances the signal from the bars. It is possible to penetrate a 2mm thick sheet at 125 Hz and image 16 mm diameter bars placed underneath.

  5. The Structure and Mechanical Properties of Bridge Steel Weldings With Glass-Steel Liners

    NASA Astrophysics Data System (ADS)

    Muzalev, V. N.; Semukhin, B. S.; Danilov, V. I.

    2016-04-01

    A new technology is developed for welding multi-span bridge constructions. The mechanical properties and structure of the low-carbon bridge steel welds have been studied. The welding parameters and application of steel-glass liners provide for long-term service of steel constructions in conformity with the welding industry specifications.

  6. Welding Metallurgy and Weldability of Stainless Steels

    NASA Astrophysics Data System (ADS)

    Lippold, John C.; Kotecki, Damian J.

    2005-03-01

    Welding Metallurgy and Weldability of Stainless Steels, the first book in over twenty years to address welding metallurgy and weldability issues associated with stainless steel, offers the most up-to-date and comprehensive treatment of these topics currently available. The authors emphasize fundamental metallurgical principles governing microstructure evolution and property development of stainless steels, including martensistic, ferric, austenitic, duplex, and precipitation hardening grades. They present a logical and well-organized look at the history, evolution, and primary uses of each stainless steel, including detailed descriptions of the associated weldability issues.

  7. Research report: User's manual for computer program AT81y003 SHABERTH. Steady state and transient thermal analysis of a shaft bearing system including ball, cylindrical and tapered roller bearings

    NASA Technical Reports Server (NTRS)

    Hadden, G. B.; Kleckner, R. J.; Ragen, M. A.; Sheynin, L.

    1981-01-01

    The SHABERTH program is capable of simulating the thermomechanical performance of a load support system consisting of a flexible shaft supported by up to five rolling element bearings. Any combination of ball, cylindrical, and tapered roller bearings can be used to support the shaft. The user can select models in calculating lubricant film thickness and traction forces. The formulation of the cage pocket/rolling element interaction model was revised to improve solution numerical convergence characteristics.

  8. 37. Photocopy of photograph. STEEL PLANT, OPEN HOUSE INSIDE PLANT ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    37. Photocopy of photograph. STEEL PLANT, OPEN HOUSE INSIDE PLANT AT TIME OF ITS OPENING, 1910. (From the Bethlehem Steel Corporation Collection, Seattle, WA) - Irondale Iron & Steel Plant, Port Townsend, Jefferson County, WA

  9. 30. Photocopy of photograph. STEEL PLANT, OPEN HEARTH FURNACE CHARGING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    30. Photocopy of photograph. STEEL PLANT, OPEN HEARTH FURNACE CHARGING CREW, 1910. (From the Bethlehem Steel Corporation Colletion, Seattle, WA) - Irondale Iron & Steel Plant, Port Townsend, Jefferson County, WA

  10. North and west facades of crucible steel building; looking southeast ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    North and west facades of crucible steel building; looking southeast - Bethlehem Steel Corporation, South Bethlehem Works, Crucible Steel Plant, Along Lehigh River, North of Fourth Street, West of Minsi Trail Bridge, Bethlehem, Northampton County, PA

  11. Addendum to the Closure Report for Corrective Action Unit 404: Roller Coaster Lagoons and Trench, Tonopah Test Range, Nevada, Revision 0

    SciTech Connect

    Lynn Kidman

    2008-10-01

    This document constitutes an addendum to the September 1998, Closure Report for Corrective Action Unit 404: Roller Coaster Lagoons and Trench, Tonopah Test Range, Nevada as described in the document Recommendations and Justifications for Modifications for Use Restrictions Established under the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office Federal Facility Agreement and Consent Order (UR Modification document) dated February 2008. The UR Modification document was approved by NDEP on February 26, 2008. The approval of the UR Modification document constituted approval of each of the recommended UR modifications. In conformance with the UR Modification document, this addendum consists of: • This cover page that refers the reader to the UR Modification document for additional information • The cover and signature pages of the UR Modification document • The NDEP approval letter • The corresponding section of the UR Modification document This addendum provides the documentation justifying the cancellation of the URs for: • CAS TA-03-001-TARC Roller Coaster Lagoons • CAS TA-21-001-TARC Roller Coaster N. Disposal Trench These URs were established as part of Federal Facility Agreement and Consent Order (FFACO) corrective actions and were based on the presence of contaminants at concentrations greater than the action levels established at the time of the initial investigation (FFACO, 1996; as amended August 2006). Since these URs were established, practices and procedures relating to the implementation of risk-based corrective actions (RBCA) have changed. Therefore, these URs were re-evaluated against the current RBCA criteria as defined in the Industrial Sites Project Establishment of Final Action Levels (NNSA/NSO, 2006c). This re-evaluation consisted of comparing the original data (used to define the need for the URs) to risk-based final action levels (FALs) developed using the current Industrial Sites RBCA process. The

  12. 77 FR 30589 - SteelRiver Infrastructure Partners LP, SteelRiver Infrastructure Associates LLC, SteelRiver...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-05-23

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF TRANSPORTATION Surface Transportation Board SteelRiver Infrastructure Partners LP, SteelRiver Infrastructure Associates..., referring to Docket No. FD 35622 must be filed with the Surface Transportation Board, 395 E Street...

  13. Post-Closure Inspection Report for Corrective Action Unit 404: Roller Coaster Lagoons and Trench Tonopah Test Range, Nevada, Calendar Year 2001

    SciTech Connect

    K. B. Campbell

    2002-01-01

    Post-closure monitoring requirements for the Roller Coaster Lagoons and Trench (Corrective Action Unit [CAU] 404) (Figure 1) are described in Closure Report for Corrective Action Unit 404. Roller Coaster Sewage Lagoons and North Disposal Trench. Tonopah Test Range. Nevada, report number DOE/NV--187, September 1998. The Closure Report (CR) was submitted to the Nevada Division of Environmental Protection (NDEP) on September 11, 1998. Permeability results of soils adjacent to the engineered cover and a request for closure of CAU 404 were transmitted to the NDEP on April 29, 1999. The CR (containing the Post-Closure Monitoring Plan) was approved by the NDEP on May 18, 1999. As stated in Section 5.0 of the NDEP-approved CRY post-closure monitoring at CAU 404 consists of the following: (1) Visual site inspections done twice a year to evaluate the condition of the cover and plant development. (2) Verification that the site is secure and condition of the fence and posted warning signs. (3) Notice of any subsidence, erosion, unauthorized excavation, etc., deficiencies that may compromise the integrity of the unit. (4) Remedy of any deficiencies within 90 days of discovery. (5) Preparation and submittal of an annual report. In addition to the above activities, vegetative monitoring of the cover (a plant census) will be done in the first, third and fifth year following revegetation. (Vegetative monitoring will done in fiscal year 2001, and the results reported in the 2002 Post-Closure Inspection Report.) Site inspections were conducted on May 16, 2001, and November 6, 2001. The site inspections were conducted after completion of the revegetation activities (October 30, 1997) and NDEP approval of the CR (May 18, 1999). All site inspections were conducted in accordance with the Post-Closure Monitoring Plan in the NDEP-approved CR. This report includes copies of inspection checklists, photographs, recommendations, and conclusions. The Post-Closure Inspection Checklists are found

  14. Corrosion behaviour of galvanized steel and electroplating steel in aqueous solution: AC impedance study and XPS

    NASA Astrophysics Data System (ADS)

    Lebrini, M.; Fontaine, G.; Gengembre, L.; Traisnel, M.; Lerasle, O.; Genet, N.

    2008-08-01

    The efficiency of a new triazole derivative, namely, 2-{(2-hydroxyethyl)[(4-methyl-1 H-1,2,3-benzotriazol-1-yl)methyl]amino}ethanol (TTA) has been studied for corrosion inhibition of galvanized steel and electroplating steel in aqueous solution. Corrosion inhibition was studied using electrochemical impedance spectroscopy (EIS). These studies have shown that TTA was a very good inhibitor. Data obtained from EIS show a frequency distribution and therefore a modelling element with frequency dispersion behaviour, a constant phase element (CPE) has been used. The corrosion behaviour of galvanized steel and electroplating steel in aqueous solution was also investigated in the presence of 4-methyl-1 H-benzotriazole (TTA unsubstituted) by EIS. These studies have shown that the ability of the molecule to adsorb on the steel surface was dependent on the group in triazole ring substituent. X-ray photoelectron spectroscopy surface analysis with TTA shows that it chemisorbed on surface of galvanized steel and electroplating steel.

  15. Corrosion Behavior of IF Steel in Various Media and Its Comparison with Mild Steel

    NASA Astrophysics Data System (ADS)

    Singh, G. P.; Moon, A. P.; Sengupta, S.; Deo, G.; Sangal, S.; Mondal, K.

    2015-05-01

    The present work discusses corrosion behavior of an interstitial-free (IF) steel in 0.6 M NaCl, 1 M NaOH, and 1 M HCl solutions, and its comparison with mild steel (MS). Dynamics polarization and AC Impedance Spectroscopy explain different polarization behaviors of the steel samples. All the steels were exposed to open atmosphere for 100 days, and to 0.6 M NaCl salt fog for 30 days. Scanning electron microscopy, x-ray diffraction, and Raman and Fourier Transformed Infrared Spectroscopy were used to characterize microstructure of the steels, rust constituents, and morphologies. Corrosion behavior of the steels has close relation with the morphology and constituents of the rusts. It has been observed that the corrosion in the IF and MS steels is uniform in nature.

  16. Evaluation of Steel Cleanliness in a Steel Deoxidized Using Al

    NASA Astrophysics Data System (ADS)

    Castro-Cedeño, Edgar-Ivan; Herrera-Trejo, Martín; Castro-Román, Manuel; Castro-Uresti, Fabián; López-Cornejo, Monserrat

    2016-06-01

    The effect of magnesium in the aluminum used as a deoxidizer on the cleanliness of steel was studied throughout a steelmaking route for the production of thin slabs. Two deoxidizers with different Mg contents were used. The Mg content of a "typical" deoxidizer was ~0.5 wt pct Mg, whereas that for an alternative deoxidizer was ~2 wt pct Mg. The inclusion population at different stages of the steelmaking process was characterized in terms of chemical composition, number, and size distribution. The inclusion modification path shows that the solid Al2O3 and Al2O3-MgO inclusions formed in the early stage of the steel ladle treatment are modified into Al2O3-MgO-CaO liquid and MgO-Al2O3-liquid inclusions. Although some slight differences were observed in the ladle furnace samples, the chemical composition of inclusions was similar in the samples taken at the mold of the continuous casting, regardless of the deoxidizer used. Gumbel, generalized extreme value (GEV), and generalized Pareto (GP) distributions were used for the description of the size distribution. The GEV and GP distributions resulted in proper distributions to describe the evolution of size distribution throughout the steelmaking process. Furthermore, no statistically significant differences between inclusion size distributions resulting from the use of either deoxidizer were found.

  17. [Initial stages of steel biocorrosion].

    PubMed

    Zhigletsova, S K; Rodin, V B; Kobelev, V S; Aleksandrova, N V; Rasulova, G E; Kholodenko, V P

    2000-01-01

    Initial stages of corrosion of mild steel induced by Klebsiela rhinoscleromatis BO2 were studied in various media. The effect of the microorganism was detected 8-10 h after inoculation. The number of viable cells were virtually unchanged within one month in all media, but the corrosive activity of the strain decreased. The corrosive activity of microorganisms can be determined by spectrophotometry even only after incubation for 24 h. At a low level of organic substrate, even strong colonization with microorganisms does not inevitably result in a significant damage to metals.

  18. Chromizing of 3Cr Steel

    SciTech Connect

    Ravi, Vilupanur; Harrison, Bradley; Koch, Jordan; Ly, Alexander; Schissler, Andrew; Pint, Bruce A; Haynes, James A

    2011-01-01

    Grade 315 steel (Fe-2.9 Cr-1.7 W-0.7 Mo-0.3 Mn-0.3 Si-0.2 V-0.1 Ni-0.13 C-0.01 N) was chromized by the halide-activated pack cementation (HAPC) process. Key process parameters, i.e., coating temperatures and pack compositions, were investigated. Ammonium chloride-activated packs in the 700-1000 C range produced coatings nominally in the 1-8 {micro}m range, as determined by optical and scanning electron microscopy (SEM). Coatings applied in the 900-1000 C temperature range resulted in Cr-rich coatings. The predominant phase in the coating was identified as Cr23C6 by X-ray diffraction. In addition, the presence of chromium nitride, Cr2N, was observed in the coating. The power generation industry is faced with an ever-increasing demand for energy while simultaneously having to reduce carbon emissions. These goals can be facilitated by increasing plant efficiency through the use of higher operating temperatures and pressures. Traditional construction materials, e.g., the ferritic Grade 22 high strength low alloy steel, are limited to operations below {approx} 550 C. Therefore, new materials are required for future plants designed to operate up to 650 C and possibly higher. These new materials need to have improved tensile strength, ductility, toughness, corrosion resistance, and creep properties at elevated temperatures. Oak Ridge National Laboratory (ORNL) is investigating the oxidation and creep behavior of various coatings on Grade 315 steel (Fe-2.9 Cr-1.7 W-0.7 Mo-0.3 Mn-0.3 Si-0.2 V-0.1 Ni-0.13 C-0.01 N), a super-bainitic steel developed for superior creep properties. Thin, chemical vapor-deposited (CVD) aluminide coatings were used to compensate for the reduced corrosion and oxidation resistance that resulted from the low chromium content of the alloy. However, the aluminized Grade 315 alloys performed less-than-favorably under conditions relevant to fossil boilers, leading to the conclusion that higher chromium contents are required for the formation of

  19. Weldability charts for constructional steels

    NASA Astrophysics Data System (ADS)

    Ion, J. C.; Ashby, M. F.

    2012-02-01

    The weldability of materials is still a poorly understood concept; a quantitative assessment remains elusive. The variables associated with welding are reduced here into two groups - processing parameters and material properties - from which two characteristic indices are defined and used as the basis of weldability charts. For the case of constructional steels, a carbon equivalent characterises both heat affected zone hardenability and the maximum hardness developed after solid state phase transformations. The welding process is characterised by its energy input. A mathematical model is used to establish relationships between the indices, which are displayed on charts as contours of microstructure and hardness.

  20. METHOD FOR JOINING ALUMINUM TO STAINLESS STEEL

    DOEpatents

    Lemon, L.C.

    1960-05-24

    Aluminum may be joined to stainless steel without the use of flux by tinning the aluminum with a tin solder containing 1% silver and 1% lead, tinning the stainless steel with a 50% lead 50% tin solder, and then sweating the tinned surfaces together.