Science.gov

Sample records for 4pi barium fluoride

  1. DANCE : a 4[pi] barium fluoride detector for measuring neutron capture on unstable nuclei /.

    SciTech Connect

    Ullmann, J. L.; Haight, Robert C.; Hunt, L. F.; Reifarth, R.; Rundberg, R. S.; Bredeweg, T. A.; Fowler, Malcolm M.; Miller, G. G.; Heil, M.; Käppeler, F.; Chamberlin, E. P.

    2002-01-01

    Measurements of neutron capture on unstable nuclei are important for studies of s-process nucleosynthesis, nuclear waste transmutation, and stewardship science. A 160-element, 4{pi} barium fluoride detector array, and associated neutron flight path, is being constructed to make capture measurements at the moderated neutron spallation source at LANSCE. Measurements can be made on as little as 1 mg of sample material over energies from near thermal to near 100 keV. The design of the DANCE array is described and neutron flux measurements from flight path commissioning are shown. The array is expected to be complete by the end of 2002.

  2. Effects of light exposure on irradiated barium fluoride crystals

    SciTech Connect

    Wuest, C.R.; Mauger, G.J.

    1993-04-20

    Small barium fluoride crystals have been irradiated using cobalt-60 gamma rays under various illumination conditions to establish the effect of photo-bleaching of the radiation-induced color centers. This paper describes results of a few different experiments conducted at LLNL over the past few weeks.

  3. Prospects for the ORNL/TAMU Barium Fluoride Array

    NASA Astrophysics Data System (ADS)

    Townsend, Austin; McIntosh, Alan; Youngs, Mike; Mosby, Shea; Varner, Robert

    2016-09-01

    Understanding the symmetry energy in the nuclear equation of state is essential to understanding properties such as the structure of a neutron star or its gravitational collapse, leading to supernovae. It has been suggested that to better constrain the symmetry energy one can use the bremmstrahlung gamma rays emitted from the hot, dense nuclear matter in the early stages of heavy ion collisions. These gamma rays have the potential to provide a cleaner probe than the more traditional hadronic probes. To measure these bremmstrahlung photons, barium fluoride scintillation crystals were chosen for their ability to detect photons across a large energy range and for their inherent pulse shape discrimination properties. This summer, the detectors of the TAMU/ORNL barium fluoride array were tested in preparation for such an experiment. Signals from each detector were recorded individually for cosmic rays and radioactive source events. The full waveforms were digitized with flash ADCs. A selected set of detectors was assembled and tested with beam from the K500 cyclotron. With this in-beam data, waveform integration parameters may be optimized. Results from the testing of these detectors with flash digitizers will be presented. Department of Energy, National Science Foundation, Cyclotron Institute.

  4. The first barium tin(II) bromide fluoride

    NASA Astrophysics Data System (ADS)

    Dénès, Georges; Merazig, Hocine; Muntasar, Abdualhafeed; Porterfield, Robyn

    2014-04-01

    In an effort to prepare barium tin(II) bromide fluorides for the first time, possibly similar to the chloride fluorides obtained earlier in our laboratory, precipitation reactions were carried out by mixing aqueous solutions of SnF2 and of BaBr2.2H2O. In contrast with the chloride fluoride system, a single powdered phase was obtained throughout the SnF2 - BaBr2 system, with the yield being maximum at X ≈ 0.25, where X is the molar fraction of barium bromide in the reaction mixture. Phase identification with the JCPDS database failed to produce a match, confirming that a new phase had been produced. The exact chemical composition of the new compound has not been obtained yet. Based on the X value for the maximum yield, the Sn/Ba ratio is likely to be 3/1 or 2/1. The Mössbauer spectrum at ambient conditions shows that bonding to tin(II) is covalent, therefore with the tin lone pair being stereoactive. The Mössbauer parameters ( δ = 3.68 mm/s, Δ = 0.99 mm/s) are similar to those of SnBrF and of Sn2BrF5, thereby showing that tin is bonded to both fluorine and bromine. The larger isomer shift and lower quadrupole splitting than in tin(II) fluorides show that the stereoactivity of the tin lone pair is lower than in the fluorides. The Mössbauer parameters fit well the linear correlation of the quadrupole splitting versus the isomer shift" that has been shown to be present in other series of tin(II) compounds. The linear decrease on this correlation shows that the contribution of non-spherical orbitals ( p and d) to the lone pair is a much larger contributor to the quadrupole splitting than lattice distortions. The structure is likely made of Ba2+ cations and tin(II) fluoride bromide polyatomic anions, with covalent bonding withinthe anions.

  5. Neutron beam test of barium fluoride crystal for dark matter direct detection

    NASA Astrophysics Data System (ADS)

    Guo, C.; Ma, X. H.; Wang, Z. M.; Bao, J.; Dai, C. J.; Guan, M. Y.; Liu, J. C.; Li, Z. H.; Ren, J.; Ruan, X. C.; Yang, C. G.; Yu, Z. Y.; Zhong, W. L.

    2016-10-01

    In order to test the capabilities of Barium Fluoride (BaF2) crystal for dark matter direct detection, nuclear recoils are studied with mono-energetic neutron beam. The energy spectra of nuclear recoils, quenching factors for elastic scattering neutrons and discrimination capability between neutron inelastic scattering events and γ events are obtained for various recoil energies of the F content in BaF2.

  6. Effect of chloride incorporation on the crystallization of zirconium-barium-lanthanum-aluminum fluoride glass

    NASA Technical Reports Server (NTRS)

    Neilson, G. F.; Smith, G. L.; Weinberg, M. C.

    1985-01-01

    One aspect of the influence of preparation procedure on the crystallization behavior of a zirconium-barium-lanthanum-aluminum fluoride glass was studied. The crystallization pattern of this glass may be affected by the chlorine concentration within it. In particular, when such glasses are heated at low temperatures, the alpha-Ba-Zr-F6 crystalline phase forms only in those glasses which contain chloride.

  7. [Using barium fluoride fine particles as stationary phase for TLC/FTIR analysis].

    PubMed

    Liu, Xi; Pan, Qing-hua; Ding, Jie; Zhu, Qing; He, An-qi; Yue, Shi-juan; Li, Xiao-pei; Hu, Li-ping; Xia, Jin-ming; Liu, Cui-ge; Wei, Yong-ju; Yu, Jiang; Yang, Zhan-lan; Zhu, Xi; Xu, Yi-zhuang; Wu, Jin-guang

    2011-07-01

    In situ TLC/FTIR technique has tremendous potential in the analysis of complex mixtures. However, the progress in this technique was quite slow. The reason is that conventional stationary phase such as silica gel etc. has strong absorption in FTIR spectrum and thus brings about severe interference in the detection of samples. To solve the problem, the authors propose to use barium fluoride fine particles as stationary phase of TLC plate. The reasons are as follows: Barium fluoride wafer has been extensively used as infrared window in FTIR experiments and it has no absorbance in an IR region between 4 000 and 800 cm'. As a matter of fact, the atomic mass of barium and fluoride is quite large, thus the normal vibration of BaF2 lattice is limited in far-IR region and low frequency part of mid-IR region. Therefore, the interference caused by IR absorption of stationary phase can be resolved if BaF2 is used as stationary phase of TLC plate. Moreover, BaF2 is quite stable and insolvable in water and most organic solvents and it will not be dissolved by mobile phase or react with samples in TLC separation. Additionally, decreasing the particle size of BaF2 is very important in TLC/FTIR analysis technique. The reason is two-fold: First, decreasing the particle size of stationary phase is helpful to improving the efficiency of separation by TLC plate; second, decreasing the size of BaFz particle can improve the quality of FTIR spectra by alleviating the problem of light scattering. By optimizing the synthetic conditions, fine particles of barium fluoride were obtained. SEM results indicate that the size of the BaF2 particles is around 500 nm. FTIR spectrum of the BaF2 particles shows that no absorption of impurity was observed. Moreover, the elevation of baseline caused by light scattering is insignificant. The authors have developed a new technique named "settlement volatilization method" to prepare TLC plate without polymeric adhesive that may bring about significant

  8. Hydrothermal synthesis, characterization and up/down-conversion luminescence of barium rare earth fluoride nanocrystals

    SciTech Connect

    Jia, Li-Ping; Zhang, Qiang; Yan, Bing

    2014-07-01

    Graphical abstract: Lanthanide ions doped bare earth rare earth fluoride nanocrystals are synthesized by hydrothermal technology and characterized. The down/up-conversion luminescence of them are discussed. - Highlights: • Mixed hydrothermal system H{sub 2}O–OA (EDA)–O-A(LO-A) is used for synthesis. • Barium rare earth fluoride nanocrystals are synthesized comprehensively. • Luminescence for down-conversion and up-conversion are obtained for these systems. - Abstract: Mixed hydrothermal system H{sub 2}O–OA (EDA)–O-A(LO-A) is developed to synthesize barium rare earth fluorides nanocrystals (OA = oleylamine, EDA = ethylenediamine, O-A = oleic acid and LO-A = linoleic acid). They are presented as BaREF{sub 5} (RE = Ce, Pr, Nd, Eu, Gd, Tb, Dy, Y, Tm, Lu) and Ba{sub 2}REF{sub 7} (RE = La, Sm, Ho, Er, Yb). The influence of reaction parameters (rare earth species, hydrothermal system and temperature) is checked on the phase and shape evolution of the fluoride nanocrystals. It is found that reaction time and temperature of these nanocrystals using EDA (180 °C, 6 h) is lower than those of them using OA (220 °C, 10 h). The photoluminescence properties of these fluorides activated by some rare earth ions (Nd{sup 3+}, Eu{sup 3+}, Tb{sup 3+}) are studied, and especially up-conversion luminescence of the four fluoride nanocrystal systems (Ba{sub 2}LaF{sub 7}:Yb, Tm(Er), Ba{sub 2}REF{sub 7}:Yb, Tm(Er) (RE = Gd, Y, Lu)) is observed.

  9. Cascaded Brillouin lasing in monolithic barium fluoride whispering gallery mode resonators

    SciTech Connect

    Lin, Guoping Diallo, Souleymane; Saleh, Khaldoun; Martinenghi, Romain; Beugnot, Jean-Charles; Sylvestre, Thibaut; Chembo, Yanne K.

    2014-12-08

    We report the observation of stimulated Brillouin scattering and lasing at 1550 nm in barium fluoride (BaF{sub 2}) crystal. Brillouin lasing was achieved with ultra-high quality (Q) factor monolithic whispering gallery mode mm-size disk resonators. Overmoded resonators were specifically used to provide cavity resonances for both the pump and all Brillouin Stokes waves. Single and multiple Brillouin Stokes radiations with frequency shift ranging from 8.2 GHz up to 49 GHz have been generated through cascaded Brillouin lasing. BaF{sub 2} resonator-based Brillouin lasing can find potential applications for high-coherence lasers and microwave photonics.

  10. Barium fluoride whispering-gallery-mode disk-resonator with one billion quality-factor.

    PubMed

    Lin, Guoping; Diallo, Souleymane; Henriet, Rémi; Jacquot, Maxime; Chembo, Yanne K

    2014-10-15

    We demonstrate a monolithic optical whispering-gallery-mode resonator fabricated with barium fluoride (BaF₂) with an ultra-high quality (Q) factor above 10⁹ at 1550 nm, and measured with both the linewidth and cavity-ring-down methods. Vertical scanning optical profilometry shows that the root mean square surface roughness of 2 nm is achieved for our mm-size disk. To the best of our knowledge, we show for the first time that one billion Q-factor is achievable by precision polishing in relatively soft crystals with mohs hardness of 3. We show that complex thermo-optical dynamics can take place in these resonators. Beside usual applications in nonlinear optics and microwave photonics, high-energy particle scintillation detection utilizing monolithic BaF₂ resonators potentially becomes feasible.

  11. Water Atomization of Barium Fluoride: Calcium Fluoride for Enhanced Flow Characteristics of PS304 Feedstock Powder Blend

    NASA Technical Reports Server (NTRS)

    Stanford, Malcolm K.; DellaCorte, Christopher

    2003-01-01

    PS304 is a plasma spray deposited solid lubricant coating with feedstock composed of NiCr, Cr2O3, Ag, and BaF2-CaF2 powders. The effects of rounded BaF2-CaF2 particles on the gravity-fed flow characteristics of PS304 feedstock have been investigated. The BaF2-CaF2 powder was fabricated by water atomization using four sets of process parameters. Each of these powders was then characterized by microscopy and classified by screening to obtain 45 to 106 micron particles and added incrementally from 0 to 10 wt% to the other constituents of the PS304 feedstock, namely nichrome, chromia, and silver powders. The relationship between feedstock flow rate, measured with the Hall flowmeter, and concentration of fluorides was found to be linear in each case. The slopes of the lines were between those of the linear relationships previously reported using angular and spherical fluorides and were closer to the relationship predicted using the rule of mixtures. The results offer a fluoride fabrication technique potentially more cost-effective than gas atomization processes or traditional comminution processes.

  12. The kinetics of fluoride sorption by zeolite: Effects of cadmium, barium and manganese

    NASA Astrophysics Data System (ADS)

    Cai, Qianqian; Turner, Brett D.; Sheng, Daichao; Sloan, Scott

    2015-06-01

    Industrial wastewaters often consist of a complex chemical cocktail with treatment of target contaminants complicated by adverse chemical reactions. The impact of metal ions (Cd2 +, Ba2 + and Mn2 +) on the kinetics of fluoride removal from solution by natural zeolite was investigated. In order to better understand the kinetics, the pseudo-second order (PSO), Hill (Hill 4 and Hill 5) and intra-particle diffusion (IPD) models were applied. Model fitting was compared using the Akaike Information Criterion (AIC) and the Schwarz Bayesian Information Criterion (BIC). The Hill models (Hill 4 and Hill 5) were found to be superior in describing the fluoride removal processes due to the sigmoidal nature of the kinetics. Results indicate that the presence of Mn (100 mg L- 1) and Cd (100 mg L- 1) respectively increases the rate of fluoride sorption by a factor of 28.3 and 10.9, the maximum sorption capacity is increased by 2.2 and 1.7. The presence of Ba (100 mg L- 1) initially inhibited fluoride removal and very poor fits were obtained for all models. Fitting was best described with a biphasic sigmoidal model with the degree of inhibition decreasing with increasing temperature suggesting that at least two processes are involved with fluoride sorption onto natural zeolite in the presence of Ba.

  13. The kinetics of fluoride sorption by zeolite: Effects of cadmium, barium and manganese.

    PubMed

    Cai, Qianqian; Turner, Brett D; Sheng, Daichao; Sloan, Scott

    2015-01-01

    Industrial wastewaters often consist of a complex chemical cocktail with treatment of target contaminants complicated by adverse chemical reactions. The impact of metal ions (Cd(2+), Ba(2+) and Mn(2+)) on the kinetics of fluoride removal from solution by natural zeolite was investigated. In order to better understand the kinetics, the pseudo-second order (PSO), Hill (Hill 4 and Hill 5) and intra-particle diffusion (IPD) models were applied. Model fitting was compared using the Akaike Information Criterion (AIC) and the Schwarz Bayesian Information Criterion (BIC). The Hill models (Hill 4 and Hill 5) were found to be superior in describing the fluoride removal processes due to the sigmoidal nature of the kinetics. Results indicate that the presence of Mn (100 mg L(-1)) and Cd (100 mg L(-1)) respectively increases the rate of fluoride sorption by a factor of ~28.3 and ~10.9, the maximum sorption capacity is increased by ~2.2 and ~1.7. The presence of Ba (100 mg L(-1)) initially inhibited fluoride removal and very poor fits were obtained for all models. Fitting was best described with a biphasic sigmoidal model with the degree of inhibition decreasing with increasing temperature suggesting that at least two processes are involved with fluoride sorption onto natural zeolite in the presence of Ba.

  14. 4Pi-RESOLFT nanoscopy

    PubMed Central

    Böhm, Ulrike; Hell, Stefan W.; Schmidt, Roman

    2016-01-01

    By enlarging the aperture along the optic axis, the coherent utilization of opposing objective lenses (4Pi arrangement) has the potential to offer the sharpest and most light-efficient point-spread-functions in three-dimensional (3D) far-field fluorescence nanoscopy. However, to obtain unambiguous images, the signal has to be discriminated against contributions from lobes above and below the focal plane, which has tentatively limited 4Pi arrangements to imaging samples with controllable optical conditions. Here we apply the 4Pi scheme to RESOLFT nanoscopy using two-photon absorption for the on-switching of fluorescent proteins. We show that in this combination, the lobes are so low that low-light level, 3D nanoscale imaging of living cells becomes possible. Our method thus offers robust access to densely packed, axially extended cellular regions that have been notoriously difficult to super-resolve. Our approach also entails a fluorescence read-out scheme that translates molecular sensitivity to local off-switching rates into improved signal-to-noise ratio and resolution. PMID:26833381

  15. Enhanced dielectric properties of poly(vinylidene fluoride) composites filled with nano iron oxide-deposited barium titanate hybrid particles

    PubMed Central

    Zhang, Changhai; Chi, Qingguo; Dong, Jiufeng; Cui, Yang; Wang, Xuan; Liu, Lizhu; Lei, Qingquan

    2016-01-01

    We report enhancement of the dielectric permittivity of poly(vinylidene fluoride) (PVDF) generated by depositing magnetic iron oxide (Fe3O4) nanoparticles on the surface of barium titanate (BT) to fabricate BT–Fe3O4/PVDF composites. This process introduced an external magnetic field and the influences of external magnetic field on dielectric properties of composites were investigated systematically. The composites subjected to magnetic field treatment for 30 min at 60 °C exhibited the largest dielectric permittivity (385 at 100 Hz) when the BT–Fe3O4 concentration is approximately 33 vol.%. The BT–Fe3O4 suppressed the formation of a conducting path in the composite and induced low dielectric loss (0.3) and low conductivity (4.12 × 10−9 S/cm) in the composite. Series-parallel model suggested that the enhanced dielectric permittivity of BT–Fe3O4/PVDF composites should arise from the ultrahigh permittivity of BT–Fe3O4 hybrid particles. However, the experimental results of the BT–Fe3O4/PVDF composites treated by magnetic field agree with percolation theory, which indicates that the enhanced dielectric properties of the BT–Fe3O4/PVDF composites originate from the interfacial polarization induced by the external magnetic field. This work provides a simple and effective way for preparing nanocomposites with enhanced dielectric properties for use in the electronics industry. PMID:27633958

  16. Enhanced dielectric properties of poly(vinylidene fluoride) composites filled with nano iron oxide-deposited barium titanate hybrid particles

    NASA Astrophysics Data System (ADS)

    Zhang, Changhai; Chi, Qingguo; Dong, Jiufeng; Cui, Yang; Wang, Xuan; Liu, Lizhu; Lei, Qingquan

    2016-09-01

    We report enhancement of the dielectric permittivity of poly(vinylidene fluoride) (PVDF) generated by depositing magnetic iron oxide (Fe3O4) nanoparticles on the surface of barium titanate (BT) to fabricate BT–Fe3O4/PVDF composites. This process introduced an external magnetic field and the influences of external magnetic field on dielectric properties of composites were investigated systematically. The composites subjected to magnetic field treatment for 30 min at 60 °C exhibited the largest dielectric permittivity (385 at 100 Hz) when the BT–Fe3O4 concentration is approximately 33 vol.%. The BT–Fe3O4 suppressed the formation of a conducting path in the composite and induced low dielectric loss (0.3) and low conductivity (4.12 × 10‑9 S/cm) in the composite. Series-parallel model suggested that the enhanced dielectric permittivity of BT–Fe3O4/PVDF composites should arise from the ultrahigh permittivity of BT–Fe3O4 hybrid particles. However, the experimental results of the BT–Fe3O4/PVDF composites treated by magnetic field agree with percolation theory, which indicates that the enhanced dielectric properties of the BT–Fe3O4/PVDF composites originate from the interfacial polarization induced by the external magnetic field. This work provides a simple and effective way for preparing nanocomposites with enhanced dielectric properties for use in the electronics industry.

  17. Enhanced dielectric properties of poly(vinylidene fluoride) composites filled with nano iron oxide-deposited barium titanate hybrid particles.

    PubMed

    Zhang, Changhai; Chi, Qingguo; Dong, Jiufeng; Cui, Yang; Wang, Xuan; Liu, Lizhu; Lei, Qingquan

    2016-09-16

    We report enhancement of the dielectric permittivity of poly(vinylidene fluoride) (PVDF) generated by depositing magnetic iron oxide (Fe3O4) nanoparticles on the surface of barium titanate (BT) to fabricate BT-Fe3O4/PVDF composites. This process introduced an external magnetic field and the influences of external magnetic field on dielectric properties of composites were investigated systematically. The composites subjected to magnetic field treatment for 30 min at 60 °C exhibited the largest dielectric permittivity (385 at 100 Hz) when the BT-Fe3O4 concentration is approximately 33 vol.%. The BT-Fe3O4 suppressed the formation of a conducting path in the composite and induced low dielectric loss (0.3) and low conductivity (4.12 × 10(-9) S/cm) in the composite. Series-parallel model suggested that the enhanced dielectric permittivity of BT-Fe3O4/PVDF composites should arise from the ultrahigh permittivity of BT-Fe3O4 hybrid particles. However, the experimental results of the BT-Fe3O4/PVDF composites treated by magnetic field agree with percolation theory, which indicates that the enhanced dielectric properties of the BT-Fe3O4/PVDF composites originate from the interfacial polarization induced by the external magnetic field. This work provides a simple and effective way for preparing nanocomposites with enhanced dielectric properties for use in the electronics industry.

  18. [The assessment of health exposure resulted from barium, boron, and fluoride intake from therapeutic waters available for resident people in water abstraction points of health resorts].

    PubMed

    Drobnik, Michał; Latour, Teresa; Sziwa, Danuta

    2010-01-01

    Estimated were chemical composition and the exploitation of therapeutic mineral waters from 139 intakes placed in 24 health resorts in Sudety and Karpaty regions. In 20 from 29 intakes available for resident people are found potentially toxic components of natural origin. There are compounds of barium, boron and fluoride of concentration exceeded the limits determined for water open for general use. Upon exposure HQ index quantity there were assessed health risk for the group of resident people resulting from long-lasting (10, 20, 30 and 70 years) consumption of definite water quantity. Certified is a high probability of appearance of undesirable health effects for people drinking permanently (over 30 years) mineral waters especially of boron or fluoride content.

  19. Divalent fluoride doped cerium fluoride scintillator

    DOEpatents

    Anderson, David F.; Sparrow, Robert W.

    1991-01-01

    The use of divalent fluoride dopants in scintillator materials comprising cerium fluoride is disclosed. The preferred divalent fluoride dopants are calcium fluoride, strontium fluoride, and barium fluoride. The preferred amount of divalent fluoride dopant is less than about two percent by weight of the total scintillator. Cerium fluoride scintillator crystals grown with the addition of a divalent fluoride have exhibited better transmissions and higher light outputs than crystals grown without the addition of such dopants. These scintillators are useful in radiation detection and monitoring applications, and are particularly well suited for high-rate applications such as positron emission tomography (PET).

  20. The Diogene 4 pi detector at Saturne

    NASA Technical Reports Server (NTRS)

    Alard, J. P.; Arnold, J.; Augerat, J.; Babinet, R.; Bastid, N.; Brochard, F.; Costilhes, J. P.; Crouau, M.; De Marco, N.; Drouet, M.; Dupieux, P.; Fanet, H.; Fodor, Z.; Fraysse, L.; Girard, J.; Gorodetzky, P.; Gosset, J.; Laspalles, C.; Lemaire, M. C.; L'Hote, D.; Lucas, B.; Montarou, G.; Papineau, A.; Parizet, M. J.; Schimmerling, W.

    1987-01-01

    Diogene, an electronic 4 pi detector, has been built and installed at the Saturne synchrotron in Saclay. The forward angular range (0 degree-6 degrees) is covered by 48 time-of-flight scintillator telescopes that provide charge identification. The trajectories of fragments emitted at larger angles are recorded in a cylindrical 0.4-m3 Pictorial Drift Chamber (PDC) surrounding the target. The PDC is inside a 1-T magnetic field; the axis of the PDC cylinder and the magnetic field are parallel to the beam. Good identification has been obtained for both positive and negative pi mesons and for hydrogen and helium isotopes. Multiplicities in relativistic nucleus-nucleus reactions up to 40 have been detected, limited mainly by the present electronics.

  1. The Diogene 4 pi detector at Saturne.

    PubMed

    Alard, J P; Arnold, J; Augerat, J; Babinet, R; Bastid, N; Brochard, F; Costilhes, J P; Crouau, M; De Marco, N; Drouet, M; Dupieux, P; Fanet, H; Fodor, Z; Fraysse, L; Girard, J; Gorodetzky, P; Gosset, J; Laspalles, C; Lemaire, M C; L'Hôte, D; Lucas, B; Montarou, G; Papineau, A; Parizet, M J; Schimmerling, W

    1987-01-01

    Diogene, an electronic 4 pi detector, has been built and installed at the Saturne synchrotron in Saclay. The forward angular range (0 degree-6 degrees) is covered by 48 time-of-flight scintillator telescopes that provide charge identification. The trajectories of fragments emitted at larger angles are recorded in a cylindrical 0.4-m3 Pictorial Drift Chamber (PDC) surrounding the target. The PDC is inside a 1-T magnetic field; the axis of the PDC cylinder and the magnetic field are parallel to the beam. Good identification has been obtained for both positive and negative pi mesons and for hydrogen and helium isotopes. Multiplicities in relativistic nucleus-nucleus reactions up to 40 have been detected, limited mainly by the present electronics.

  2. Barium enema

    MedlinePlus

    Lower gastrointestinal series; Lower GI series; Colorectal cancer - lower GI series; Colorectal cancer - barium enema; Crohn disease - lower GI series; Crohn disease - barium enema; Intestinal blockage - lower GI series; Intestinal blockage - ...

  3. HREXI prototype for 4piXIO

    NASA Astrophysics Data System (ADS)

    Grindlay, Jonathan

    We propose to complete our development of the High Resolution Energetic X-ray Imager (HREXI) and to build and test a full Engineering Model of a detector and telescope system for a 12U Cubesat that will be proposed for a test flight. This will enable a future SMEX (or MIDEX) proposal for a 4piXIO mission: a constellation of Cubesats (or Smallsats) that would dramatically increase the sensitivity, source location precision and especially number of Gamma Ray Bursts (GRBs) to explore the Early Universe. Over the past two years of our current APRA grant, we have developed the world's first (to our knowledge) readout of a high-level imaging detector that is entirely three dimensional so that imaging detectors can then be tiled in close-packed arrays of arbitrary total area. This important new technology is achieved by replacing the external lateral readout of an ASIC, which reads out data from (for example) a 2 x 2 cm imaging detector through "wire bonds" to external circuits in the same plane but beyond the detector, with a vertical readout through the ASIC itself to external circuits directly below. This new technology greatly simplifies the assembly of the large area, tiled arrays of such detectors and their readout ASICs used for coded aperture wide-field telescopes that are uniquely able to discover and study X-ray (and low energy gamma-ray) transients and bursts that are key to understanding the physics and evolution of black holes. The first actual fabrication of such 3D-readout of close-tiled HREXI imaging detectors is underway and will be demonstrated in this third and final year of the current APRA grant. This proposal takes the HREXI detector concept a major step further. By incorporating this technology into the design and fabrication of a complete Engineering Model of a HREXI detector and coded aperture telescope that would fit, with comfortable margins, in a 12U Cubesat, it opens the way for a future low-cost constellation of 25 such 12U Cubesats to

  4. Search for the CP forbidden decay eta-->4pi(0)

    PubMed

    Prakhov; Tippens; Allgower; Bekrenev; Berger; Briscoe; Clajus; Comfort; Craig; Grosnick; Huber; Isenhower; Knecht; Koetke; Koulbardis; Kozlenko; Kruglov; Kycia; Lolos; Lopatin; Manley; Marusic; Manweiler; McDonald; Nefkens; Olmsted

    2000-05-22

    We report the first determination of the upper limit for the branching ratio of the CP forbidden decay eta-->4pi(0). No events were observed in a sample of 3.0x10(7) eta decays. The experiment was performed with the Crystal Ball multiphoton spectrometer installed in a separated pi(-) beam at the AGS (Alternating Gradient Synchrotron). At the 90% confidence limit, B(eta-->4pi(0))

  5. Barium Sulfate

    MedlinePlus

    ... uses a computer to put together x-ray images to create cross-sectional or three dimensional pictures of the inside of the body). Barium sulfate is in a class of medications called radiopaque contrast media. It works by coating the esophagus, stomach, or ...

  6. Barium cyanide

    Integrated Risk Information System (IRIS)

    Barium cyanide ; CASRN 542 - 62 - 1 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic Ef

  7. 4Pi-SHG imaging of mammalian myofibrillar structures

    NASA Astrophysics Data System (ADS)

    Vogel, Martin; Hahn, Dorothea; Schürmann, Sebastian; Lang, Marion; Wegner, Frederic v.; Friedrich, Oliver; Engelhardt, Johann; Hell, Stefan W.; Fink, Rainer H.

    2006-02-01

    Intrinsic Second Harmonic Generation (SHG) signals obtained from the motor protein myosin are of particular interest for 3D-imaging of living muscle cells. In addition, the new and powerful tool of 4Pi microscopy allows to markedly enhance the optical resolution of microscopy as well as the sensitivity for small objects because of the high peak intensities due to the interference pattern created in the focus. In the present study, we report, to our knowledge for the first time, measurements of intrinsic SHG signals under 4Pi conditions of type A. These measurements on mammalian myofibrilar structures are combined with very high resolution 4Pi fluorescence data obtained from the same preparations. We have chosen myofibrillar preparations of isolated mammalian muscle fibers as they (i) possess a regular repetitive pattern of actin and myosin filaments within sarcomers 2 to 3 μm in length, (ii) consist of single myofibrils of small total diameter of approximately 1 μm and (iii) are ideally suited to study the biomedically important process of force generation via calcium regulated motor protein interactions. Myofibrillar preparations were obtained from murine skeletal and heart muscle by using a combined chemical and mechanical fractionation1 (Both et al. 2004, JBO 9(5):882-892). BODIPY FL phallacidin has been used to fluorescently label the actin filaments. The experiments were carried out with a Leica SP2 multi photon microscope modified for 4Pi measurements using a Ti:Sa laser tuned to 850-900 nm. SHG as well as fluorescence photons were detected confocally by a counting APD detector. The approach taken our study provides new 3D-data for the analysis and simulation of the important process of excitation-contraction coupling under normal physiological as well as under pathophysiological conditions.

  8. Optical properties of Cr3+ and Nd3+ in singly- and doubly-doped barium-indium-gallium-based fluoride glass investigated by time-resolved laser spectroscopy

    NASA Astrophysics Data System (ADS)

    Elejalde, M. J.; Balda, R.; Fernández, J.; Macho, E.; Adam, J. L.

    1992-09-01

    The optical properties of Cr3+-, Nd3+-, and Cr3+:Nd3+-doped fluoride glass (30BaF2-18InF3-12GaF3-20ZnF2-10YF3-6ThF4-4ZrF4) have been investigated in the 4.2-300-K temperature range at several concentrations by using steady-state and time-resolved laser spectroscopy. The luminescence of trivalent chromium in singly-doped glass shows a strong thermal quenching and can be analyzed on the basis of two broad statistical site distributions. The luminescence quenching of the 4F3/2-->4I11/2 laser transition of Nd3+ in singly-doped glass has been studied by investigating the thermal and concentration dependence of lifetimes. A T3 dependence for the nonradiative Nd3+-Nd3+ relaxation has been found in the 15-100-K temperature range at high Nd3+ concentrations, which is in agreement with a two-site nonresonant process. Cr3+-to-Nd3+ radiative and nonradiative energy transfer in codoped glass has been demonstrated from the emission spectra and the decrease of Cr3+ fluorescence lifetimes. The comparison between the time-resolved emission spectra of Cr3+ singly-doped and codoped samples indicates a very rapid Cr3+-->Nd3+ energy-transfer process with a lower limit of 107 s-1. The nonradiative Cr3+-->Nd3+ energy transfer is consistent with an electric-dipole-electric-dipole interaction mechanism. The transfer efficiency corrected for Nd3+-Nd3+ self-quenching is in agreement with the measured Nd3+ luminescence transferred by Cr3+ donors.

  9. A 4. pi. tracking TPC magnetic spectrometer for RHIC

    SciTech Connect

    Danby, G.; Eiseman, S.E.; Etkin, A.; Foley, K.J.; Hackenburg, R.W.; Longacre, R.S.; Love, W.A.; Morris, T.W.; Platner, E.D.; Saulys, A.C.; Van Dijk, J.H. ); Lindenbaum, S.J. City Coll., New York, NY ); Chan, C.S.; Kramer, M.A.; Zhao, K. ); Biswas, N.; Kenney, P.; Piekarz, J. (Notre Dame Univ

    1990-01-01

    The primary physics objective of the 4{pi} TPC magnetic spectrometer proposal is to search for the Quark-Gluon Plasma. In previous workshops we have discussed what the possible hadronic signatures of such a state of matter would be. Succinctly, the QGP is a direct prediction of non-perturbative QCD. Therefore the question of the existence of this new state of matter bears directly on the validity of non-perturbative QCD. However, since non-perturbative QCD has never been established, it is apparent that what may await us is a host of new phenomena that will go beyond the standard model.

  10. Barium uranyl diphosphonates

    SciTech Connect

    Nelson, Anna-Gay D.; Alekseev, Evgeny V.; Ewing, Rodney C.; Albrecht-Schmitt, Thomas E.

    2012-08-15

    Three Ba{sup 2+}/UO{sub 2}{sup 2+} methylenediphosphonates have been prepared from mild hydrothermal treatment of uranium trioxide, methylendiphosphonic acid (C1P2) with barium hydroxide octahydrate, barium iodate monohydrate, and small aliquots of HF at 200 Degree-Sign C. These compounds, Ba[UO{sub 2}[CH{sub 2}(PO{sub 3}){sub 2}]{center_dot}1.4H{sub 2}O (Ba-1), Ba{sub 3}[(UO{sub 2}){sub 4}(CH{sub 2}(PO{sub 3}){sub 2}){sub 2}F{sub 6}]{center_dot}6H{sub 2}O (Ba-2), and Ba{sub 2}[(UO{sub 2}){sub 2}(CH{sub 2}(PO{sub 3}){sub 2})F{sub 4}]{center_dot}5.75H{sub 2}O (Ba-3) all adopt layered structures based upon linear uranyl groups and disphosphonate molecules. Ba-2 and Ba-3 are similar in that they both have UO{sub 5}F{sub 2} pentagonal bipyramids that are bridged and chelated by the diphosphonate moiety into a two-dimensional zigzag anionic sheet (Ba-2) and a one-dimensional ribbon anionic chain (Ba-3). Ba-1, has a single crystallographically unique uranium metal center where the C1P2 ligand solely bridges to form [UO{sub 2}[CH{sub 2}(PO{sub 3}){sub 2}]{sup 2-} sheets. The interlayer space of the structures is occupied by Ba{sup 2+}, which, along with the fluoride ion, mediates the structure formed and maintains overall charge balance. - Graphical abstract: Illustration of the stacking of the layers in Ba{sub 3}[(UO{sub 2}){sub 4}(CH{sub 2}(PO{sub 3}){sub 2}){sub 2})F{sub 6}]{center_dot}6H{sub 2}O viewed along the c-axis. The structure is constructed from UO{sub 7} pentagonal bipyramidal units, U(1)O{sub 7}=gray, U(2)O{sub 7}=yellow, barium=blue, phosphorus=magenta, fluorine=green, oxygen=red, carbon=black, and hydrogen=light peach. Highlights: Black-Right-Pointing-Pointer The polymerization of the UO{sub 2}{sup 2+} sites to form uranyl dimers leads to structural variations in compounds. Black-Right-Pointing-Pointer Barium cations stitch uranyl diphosphonate anionic layers together, and help mediate structure formation. Black-Right-Pointing-Pointer HF acts as both a

  11. Manipulation of resonant metallic nanoparticle using 4Pi focusing system.

    PubMed

    Wang, Xiaoyan; Rui, Guanghao; Gong, Liping; Gu, Bing; Cui, Yiping

    2016-10-17

    Metallic nanoparticles have fascinated scientists for over a century and are now heavily utilized in biomedical sciences and engineering. Due to its noncontact and holding nature, optical trapping is suitable to be combined with various applications to manipulate metallic nanoparticles. However, stable trapping of resonant metallic nanoparticles remains challenging due to the strong axial scattering force and severe optical heating effect. In this work, we propose novel optical tweezers constructed around a 4Pi focusing system that is capable of manipulating metallic nanoparticles even under the resonant condition. By properly modulating the spatial distribution of the illumination and adjusting the focusing condition, specific numbers of spherical spots with controllable locations can be generated in the focal region, providing multiple probes to interrogate the sample properties. Besides, stable three-dimensional optical trapping can be formed since the axial scattering force is canceled by the counter-propagating light. The greatly enhanced optical force arising from the extremely high focusing efficiency of the 4Pi focusing system enables to avoid the overheating effect by reducing the input power without destroying the mechanical stability. Moreover, complex motion trajectory of the metallic nanoparticles can be realized via introducing specific phase modulation to the illumination sequentially. The technique demonstrated in this work may open up new avenues for optical manipulation and their applications in various scientific fields.

  12. Fluoridated Water

    MedlinePlus

    ... Genetics Services Directory Cancer Prevention Overview Research Fluoridated Water On This Page What is fluoride, and where is it found? What is water fluoridation? When did water fluoridation begin in the ...

  13. Fluoridation Basics

    MedlinePlus

    ... Water Fluoridation Journal Articles for Community Water Fluoridation Water Fluoridation Basics Recommend on Facebook Tweet Share Compartir ... because of tooth decay. History of Fluoride in Water In the 1930s, scientists examined the relationship between ...

  14. 4. pi. data of relativistic nuclear collisions. [Plastic ball

    SciTech Connect

    Gutbrod, H.H.; Gustafsson, H.A.; Kolb, B.

    1983-05-01

    During the past two years, complete events of relativistic nuclear collisions are being studied with the Plastic Ball, the first electronic nonmagnetic particle-identifying 4..pi.. spectrometer. It is well suited to handle the large multiplicities in these reactions and allows collection of data at a rate sufficient to make further software selections to look at rare events. The analysis of the data follows various lines covering topics like thermalization, stopping or transparency, cluster-production mechanism (--can it tell entropy), search for collective flow through various global analyzing methods that allow determination of the scattering plane, projectile fragmentation (--is there a bounce-off), pion distribution, two-particle correlations: Hanbury-Brown Twiss, and excited nuclear states (--nucleosynthesis at the freezeout point or from chemical equilibrium). We will cover in this contribution only two subjects: stopping and thermalization and cluster production.

  15. VizieR Online Data Catalog: HI4PI spectra and column density maps (HI4PI team+, 2016)

    NASA Astrophysics Data System (ADS)

    Hi4PI Collaboration; Ben Bekhti, N.; Floeer, L.; Keller, R.; Kerp, J.; Lenz, D.; Winkel, B.; Bailin, J.; Calabretta, M. R.; Dedes, L.; Ford, H. A.; Gibson, B. K.; Haud, U.; Janowiecki, S.; Kalberla, P. M. W.; Lockman, F. J.; McClure-Griffiths, N. M.; Murphy, T.; Nakanishi, H.; Pisano, D. J.; Staveley-Smith, L.

    2016-09-01

    The HI4PI data release comprises 21-cm neutral atomic hydrogen data of the Milky Way (-600km/s0°; -470km/s4PI covers the full 4-pi sky. Spectral data is provided in three forms: (1) Standard FITS data cubes, for the full sky in both, Equatorial (J2000) and Galactic coordinates, each in four different map projections, AIT, CAR, MOL, and SFL; see world-coordinate-system, WCS, references: Greisen & Calabretta, 2002A&A...395.1061G, Calabretta & Greisen, 2002A&A...395.1077C, Greisen et al., 2006A&A...446..747G (2) Smaller FITS data cubes, each having a size of about 20x20 sq.deg. For convenience, we provide four different map projections, CAR, SFL, SIN, and TAN (again see WCS references). Note, size in longitude is 20° in absolute coordinates for CAR projection, and 20° true-angular size for SFL, SIN, and TAN projections. Again, Equatorial and Galactic coordinate systems are provided. (3) FITS binary tables containing lists of spectra sampled on a HealPIX grid (nside=1024, Galactic coordinates, Ring indexing scheme, Gorski et al., 2005ApJ...622..759G). To make handling of the data easier, the table is split into smaller files. Each of these contains spectra belonging to one of the 192 base/parent pixels of the nside=4 pixelization. For convenience, the binary tables also contain EQ2000 and Galactic coordinate positions for each individual spectrum, as well as the associated HealPIX index. Furthermore, we provide the full-sky HI column density distribution, both, in a (1) HealPIX-grid binary table (nside=1024, Galactic coordinates, Ring indexing scheme), and (2) Standard FITS 2D images in four map projections, AIT, CAR, MOL, and SFL. Various velocity intervals were applied to calculate NHI. Equatorial and Galactic coordinate systems are provided. (16 data files).

  16. Radiation damage in barium fluoride detector materials

    SciTech Connect

    Levey, P.W.; Kierstead, J.A.; Woody, C.L.

    1988-01-01

    To develop radiation hard detectors, particularly for high energy physics studies, radiation damage is being studied in BaF/sub 2/, both undoped and doped with La, Ce, Nd, Eu, Gd and Tm. Some dopants reduce radiation damage. In La doped BaF/sub 2/ they reduce the unwanted long lifetime luminescence which interferes with the short-lived fluorescence used to detect particles. Radiation induced coloring is being studied with facilities for making optical measurements before, during and after irradiation with /sup 60/C0 gamma rays. Doses of 10/sup 6/ rad, or less, create only ionization induced charge transfer effects since lattice atom displacement damage is negligible at these doses. All crystals studied exhibit color center formation, between approximately 200 and 800 nm, during irradiation and color center decay after irradiation. Thus only measurements made during irradiation show the total absorption present in a radiation field. Both undoped and La doped BaF/sub 2/ develop damage at minimum detectable levels in the UV---which is important for particle detectors. For particle detector applications these studies must be extended to high dose irradiations with particles energetic enough to cause lattice atom displacement damage. In principle, the reduction in damage provided by dopants could apply to other applications requiring radiation damage resistant materials.

  17. BARIUM RECOVERY PROCESS

    DOEpatents

    Blanco, R.E.

    1959-07-21

    A method of separating barium from nuclear fission products is described. In accordance with the invention, barium may be recovered from an acidic solution of neutron-irradiated fissionable material by carrying ihe barium cut of solution as a sulfate with lead as a carrier and then dissolving the barium-containing precipitate in an aqueous solution of an aliphatic diamine chelating reagent. The barium values together with certain other metallic values present in the diamine solution are then absorbed onto a cation exchange resin and the barium is selectively eluted from the resin bed with concentrated nitric acid.

  18. Zirconium fluoride glass - Surface crystals formed by reaction with water

    NASA Technical Reports Server (NTRS)

    Doremus, R. H.; Bansal, N. P.; Bradner, T.; Murphy, D.

    1984-01-01

    The hydrated surfaces of a zirconium barium fluoride glass, which has potential for application in optical fibers and other optical elements, were observed by scanning electron microscopy. Crystalline zirconium fluoride was identified by analysis of X-ray diffraction patterns of the surface crystals and found to be the main constituent of the surface material. It was also found that hydrated zirconium fluorides form only in highly acidic fluoride solutions. It is possible that the zirconium fluoride crystals form directly on the glass surface as a result of its depletion of other ions. The solubility of zirconium fluoride is suggested to be probably much lower than that of barium fluoride (0.16 g/100 cu cm at 18 C). Dissolution was determined to be the predominant process in the initial stages of the reaction of the glass with water. Penetration of water into the glass has little effect.

  19. Barium enema (image)

    MedlinePlus

    A barium enema is performed to examine the walls of the colon. During the procedure, a well lubricated enema tube is inserted gently into the rectum. The barium, a radiopaque (shows up on X-ray) contrast ...

  20. Optimal Fluoridation

    PubMed Central

    Lee, John R.

    1975-01-01

    Optimal fluoridation has been defined as that fluoride exposure which confers maximal cariostasis with minimal toxicity and its values have been previously determined to be 0.5 to 1 mg per day for infants and 1 to 1.5 mg per day for an average child. Total fluoride ingestion and urine excretion were studied in Marin County, California, children in 1973 before municipal water fluoridation. Results showed fluoride exposure to be higher than anticipated and fulfilled previously accepted criteria for optimal fluoridation. Present and future water fluoridation plans need to be reevaluated in light of total environmental fluoride exposure. PMID:1130041

  1. Carbide-fluoride-silver self-lubricating composite

    NASA Technical Reports Server (NTRS)

    Sliney, Harold E. (Inventor)

    1987-01-01

    A self-lubricating, friction and wear reducing composite material is described for use over a wide temperature spectrum from cryogenic temperature to about 900 C in a chemically reactive environment comprising silver, barium fluoride/calcium fluoride eutectic, and metal bonded chromium carbide.

  2. Carbide/fluoride/silver self-lubricating composite

    NASA Technical Reports Server (NTRS)

    Sliney, Harold E. (Inventor)

    1988-01-01

    A self-lubricating, friction and wear reducing composite material for use over a wide temperature spectrum from cryogenic temperature to about 900.degree. C. in a chemically reactive environment comprising silver, barium fluoride/calcium fluoride eutectic, and metal bonded chromium carbide.

  3. Fluoride laser crystals: old and new

    NASA Astrophysics Data System (ADS)

    Jenssen, Hans P.; Cassanho, Arlete

    2006-02-01

    The development of oxide and fluoride materials as gain materials of choice for solid state lasers ranges from early materials such as Calcium Fluoride and Calcium Tungstate crystals to the now ubiquitous Nd hosts YLF, YAG and Vanadate. Among Tunable laser materials, MgF II - an early favorite, gave way to superior oxides such as Alexandrite and Ti:Sapphire only to be followed by development of still newer tunable fluoride media, notably, fluoride colquiriites such as Cr-doped LiSAF and LiCaF. Newer fluoride crystals, such as Barium Yttrium Fluoride BaY II F 8 (BYF), KY 3F 10 (KYF) and the tunable Cr doped LiCaGaF 6 are attractive laser materials, but their growth has not been optimized. Key advantages of two of these new crystals are discussed. Crystal growth results for BYF and Cr:LiCaGaF 6 as well as some material characterization are presented.

  4. Systemic fluoride.

    PubMed

    Sampaio, Fábio Correia; Levy, Steven Marc

    2011-01-01

    There is substantial evidence that fluoride, through different applications and formulas, works to control caries development. The first observations of fluoride's effects on dental caries were linked to fluoride naturally present in the drinking water, and then from controlled water fluoridation programs. Other systemic methods to deliver fluoride were later suggested, including dietary fluoride supplements such as salt and milk. These systemic methods are now being questioned due to the fact that many studies have indicated that fluoride's action relies mainly on its post-eruptive effect from topical contact with the tooth structure. It is known that even the methods of delivering fluoride known as 'systemic' act mainly through a topical effect when they are in contact with the teeth. The effectiveness of water fluoridation in many geographic areas is lower than in previous eras due to the widespread use of other fluoride modalities. Nevertheless, this evidence should not be interpreted as an indication that systemic methods are no longer relevant ways to deliver fluoride on an individual basis or for collective health programs. Caution must be taken to avoid excess ingestion of fluoride when prescribing dietary fluoride supplements for children in order to minimize the risk of dental fluorosis, particularly if there are other relevant sources of fluoride intake - such as drinking water, salt or milk and/or dentifrice. Safe and effective doses of fluoride can be achieved when combining topical and systemic methods.

  5. Dentifrice Fluoride

    NASA Astrophysics Data System (ADS)

    Rakita, Philip E.

    2004-05-01

    The effectiveness of the fluoride ion in lowering the incidence of dental caries is a major factor in the field of dental health. Observations and research studies in the first half of the 20th century have lead to the widespread adoption of fluoridated water and the use of inorganic fluoride compounds in oral care products, such as toothpaste and dental rinses. This article provides a brief review of the types of compounds used and the chemistry involved.

  6. Barium bright and heavy

    NASA Astrophysics Data System (ADS)

    Fromm, Katharina M.

    2013-02-01

    Katharina M. Fromm relates how barium and its ores went from a magical, glowing species that attracted witches and alchemists to components in a variety of compounds that are key parts of modern life.

  7. 4Pi fluorescence detection and 3D particle localization with a single objective

    PubMed Central

    Schnitzbauer, J.; McGorty, R.; Huang, B.

    2013-01-01

    Coherent detection through two opposing objectives (4Pi configuration) improves the precision of three-dimensional (3D) single-molecule localization substantially along the axial direction, but suffers from instrument complexity and maintenance difficulty. To address these issues, we have realized 4Pi fluorescence detection by sandwiching the sample between the objective and a mirror, and create interference of direct incidence and mirror-reflected signal at the camera with a spatial light modulator. Multifocal imaging using this single-objective mirror interference scheme offers improvement in the axial localization similar to the traditional 4Pi method. We have also devised several PSF engineering schemes to enable 3D localization with a single emitter image, offering better axial precision than normal single-objective localization methods such as astigmatic imaging. PMID:24105517

  8. 4Pi microscopy of type A with 1-photon excitation in biological fluorescence imaging

    NASA Astrophysics Data System (ADS)

    Lang, Marion; Müller, Tobias; Engelhardt, Johann; Hell, Stefan W.

    2007-03-01

    We demonstrate that oil immersion lenses with a semi-aperture angle ≥ 74° enable 4Pi confocal fluorescence microscopy of type A with 1 photon excitation. The axial sidelobes amount to < 50 % of the main diffraction maximum, implying that lobe induced artifacts can be removed from the image data. The advancement reported herein enables a relative inexpensive implementation of 4Pi microscopy, providing axially superresolved 3D-imaging in transparent samples. As an example, we show dual-color 4Pi images of double stained Golgi stacks in a mammalian cell with 110 nm axial resolution. The resolution can be further enhanced to values slightly below 100 nm by image deconvolution.

  9. Optimized Photorefractive Barium Titanate

    DTIC Science & Technology

    1992-03-11

    potassium dihydrogen phosphate (KDP), 6 and barium sodium niobate Ba2 NaNbsO%1 ,7 were examined. Unfortu- nately, the high optical intensities required for...Phys. Lett., 15, 210 (1969) 14. J. J. Amodei. D. L. Staebler. and A. W. Stephens, "Holographic Storage in Doped Barium Sodium Niobate ". Appl. Phys...equipped with precise computer control of the pulling and rotation system. The cylindrical furnace was found to be susceptible to cracking due to

  10. Bottled Water and Fluoride

    MedlinePlus

    ... Fluoridation Journal Articles for Community Water Fluoridation Bottled Water Recommend on Facebook Tweet Share Compartir Consumers drink ... questions about bottled water and fluoride. Does bottled water contain fluoride? Bottled water products may contain fluoride, ...

  11. A review of 4/pi/ /hacek C/erenkov ring imaging detectors

    SciTech Connect

    Leith, D.W.G.S

    1989-06-01

    The design choices for 4/pi/ ring imaging /hacek C/erenkov counters -- both those of principle and those of practice -- are reviewed. The progress in construction and the performance of the devices being built for DELPHI and SLD are discussed. 13 refs., 22 figs.

  12. Observed Barium Emission Rates

    NASA Technical Reports Server (NTRS)

    Stenbaek-Nielsen, H. C.; Wescott, E. M.; Hallinan, T. J.

    1993-01-01

    The barium releases from the CRRES satellite have provided an opportunity for verifying theoretically calculated barium ion and neutral emission rates. Spectra of the five Caribbean releases in the summer of 1991 were taken with a spectrograph on board a U.S. Air Force jet aircraft. Because the line of sight release densities are not known, only relative rates could be obtained. The observed relative rates agree well with the theoretically calculated rates and, together with other observations, confirm the earlier detailed theoretical emission rates. The calculated emission rates can thus with good accuracy be used with photometric observations. It has been postulated that charge exchange between neutral barium and oxygen ions represents a significant source for ionization. If so. it should be associated with emissions at 4957.15 A and 5013.00 A, but these emissions were not detected.

  13. Barium and Compounds

    Integrated Risk Information System (IRIS)

    EPA / 635 / R - 05 / 001 www.epa.gov / iris TOXICOLOGICAL REVIEW OF BARIUM AND COMPOUNDS ( CAS No . 7440 - 39 - 3 ) In Support of Summary Information on the Integrated Risk Information System ( IRIS ) March 1998 Minor revisions January 1999 Reference dose revised June 2005 U.S . Environmental Protec

  14. HI4PI: A full-sky H I survey based on EBHIS and GASS

    NASA Astrophysics Data System (ADS)

    HI4PI Collaboration; Ben Bekhti, N.; Flöer, L.; Keller, R.; Kerp, J.; Lenz, D.; Winkel, B.; Bailin, J.; Calabretta, M. R.; Dedes, L.; Ford, H. A.; Gibson, B. K.; Haud, U.; Janowiecki, S.; Kalberla, P. M. W.; Lockman, F. J.; McClure-Griffiths, N. M.; Murphy, T.; Nakanishi, H.; Pisano, D. J.; Staveley-Smith, L.

    2016-10-01

    Context. Measurement of the Galactic neutral atomic hydrogen (H I) column density, NH I, and brightness temperatures, TB, is of high scientific value for a broad range of astrophysical disciplines. In the past two decades, one of the most-used legacy H I datasets has been the Leiden/Argentine/Bonn Survey (LAB). Aims: We release the H I 4π survey (HI4PI), an all-sky database of Galactic H I, which supersedes the LAB survey. Methods: The HI4PI survey is based on data from the recently completed first coverage of the Effelsberg-Bonn H I Survey (EBHIS) and from the third revision of the Galactic All-Sky Survey (GASS). EBHIS and GASS share similar angular resolution and match well in sensitivity. Combined, they are ideally suited to be a successor to LAB. Results: The new HI4PI survey outperforms the LAB in angular resolution (ϑFWHM = 16´´.2) and sensitivity (σrms = 43 mK). Moreover, it has full spatial sampling and thus overcomes a major drawback of LAB, which severely undersamples the sky. We publish all-sky column density maps of the neutral atomic hydrogen in the Milky Way, along with full spectroscopic data, in several map projections including HEALPix. HI4PI datasets are only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (http://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/594/A116

  15. Containerless processing of fluoride glass

    NASA Technical Reports Server (NTRS)

    Doremus, Robert H.

    1990-01-01

    Ground-based experiments on glass formation, crystallization, surface tension, vaporization, and chemical durability of a zirconium-barium-lanthanum (ZBL) fluoride glass are summarized. In a container large, columnar grains grew out from the container-glass interface during cooling. The main crystalline phase was alpha BaZrF6. A ZBL glass sphere was levitated acoustically during Shuttle flight STS-11. The glass was melted and then cooled while being levitated (containerless). Crystallization in the recovered sample was very fine and mainly beta BaZr2F10, showing the influence of the container on the nucleation and microstructure of crystallization in the glass. Glass formation should be easier for a containerless glass than in a container.

  16. Fluoride absorption: independence from plasma fluoride levels

    SciTech Connect

    Whitford, G.M.; Williams, J.L.

    1986-04-01

    The concept that there are physiologic mechanisms to homeostatically regulate plasma fluoride concentrations has been supported by results in the literature suggesting an inverse relationship between plasma fluoride levels and the absorption of the ion from the gastrointestinal tract of the rat. The validity of the relationship was questioned because of possible problems in the experimental design. The present work used four different methods to evaluate the effect of plasma fluoride levels on the absorption of the ion in rats: (i) the percentage of the daily fluoride intake that was excreted in the urine; (ii) the concentration of fluoride in femur epiphyses; (iii) the net areas under the time-plasma fluoride concentration curves after intragastric fluoride doses; and (iv) the residual amounts or fluoride in the gastrointestinal tracts after the intragastric fluoride doses. None of these methods indicated that plasma fluoride levels influence the rate or the degree or fluoride absorption. It was concluded that, unless extremely high plasma fluoride levels are involved (pharmacologic or toxic doses), the absorption of the ion is independent of plasma levels. The results provide further evidence that plasma fluoride concentrations are not homeostatically regulated.

  17. On Barium Oxide Solubility in Barium-Containing Chloride Melts

    NASA Astrophysics Data System (ADS)

    Nikolaeva, Elena V.; Zakiryanova, Irina D.; Bovet, Andrey L.; Korzun, Iraida V.

    2016-08-01

    Oxide solubility in chloride melts depends on temperature and composition of molten solvent. The solubility of barium oxide in the solvents with barium chloride content is essentially higher than that in molten alkali chlorides. Spectral data demonstrate the existence of oxychloride ionic groupings in such melts. This work presents the results of the BaO solubility in two molten BaCl2-NaCl systems with different barium chloride content. The received data together with earlier published results revealed the main regularities of BaO solubility in molten BaO-BaCl2-MCl systems.

  18. Search for tau- ---> 4pi- 3pi+ (pi0) nu/tau Decays

    SciTech Connect

    Ter-Antonian, R.; Kass, R.; Allmendinger, T.; Hast, C.; /SLAC

    2005-06-21

    A search for the decay of the {tau} lepton to seven charged pions and at most one {pi}{sup 0} was performed using the BABAR detector at the PEP-II e{sup +}e{sup -} collider. The analysis uses data recorded on and near the {Upsilon}(4S) resonance between 1999 and 2003, a total of 124.3 fb{sup -1}. They observe 7 events with an expected background of 11.9 {+-} 2.2 events and calculate a preliminary upper limit of BR({tau}{sup -} {yields} 4{pi}{sup -} 3{pi}{sup +}({pi}{sup 0}){nu}{sub {tau}}) < 2.7 x 10{sup -7} at 90% CL. This is a significant improvement over the previous limit established by the CLEO Collaboration.

  19. Hydrothermally synthesized barium fluoride nanocubes for thermoluminescence dosimetry

    NASA Astrophysics Data System (ADS)

    Bhadane, Mahesh S.; Dahiwale, S. S.; Bhoraskar, V. N.; Dhole, S. D.

    2016-05-01

    In this work, we report a hydrothermally synthesized Dy doped BaF2 (BaF2:Dy) nanocubes and its Thermoluminescence studies. The synthesized BaF2:Dy samples was found to posses FCC structure and having average size ~ 60-70 nm, as revealed through X-Ray Diffraction. Cubical morphology having size ~90 nm was observed from TEM analysis. The 60Co γ- ray irradiated BaF2:Dy TL dosimetric experiments shows a pre-dominant single glow peak at 153 °C, indicating a single level trap present as a metastable state. Furthermore, BaF2:Dy nanophosphor shows a sharp linear response from 10 Gy to 3 kGy, thus it can be applicable as a gamma dosimeter.

  20. Abundance analysis of barium and mild barium stars

    NASA Astrophysics Data System (ADS)

    Smiljanic, R.; Porto de Mello, G. F.; da Silva, L.

    2007-06-01

    Aims:We compare and discuss abundances and trends in normal giants, mild barium, and barium stars, searching for differences and similarities between barium and mild barium stars that could help shed some light on the origin of these similar objects. Also, we search for nucleosynthetic effects possibly related to the s-process that were observed in the literature for elements like Cu in other types of s-process enriched stars. Methods: High signal to noise, high resolution spectra were obtained for a sample of normal, mild barium, and barium giants. Atmospheric parameters were determined from the Fe i and Fe ii lines. Abundances for Na, Mg, Al, Si, Ca, Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Sr, Y, Zr, Ba, La, Ce, Nd, Sm, Eu, and Gd, were determined from equivalent widths and model atmospheres in a differential analysis, with the red giant ɛ Vir as the standard star. Results: The different levels of s-process overabundances of barium and mild barium stars were earlier suggested to be related to the stellar metallicity. Contrary to this suggestion, we found in this work no evidence of barium and mild barium having a different range in metallicity. However, comparing the ratio of abundances of heavy to light s-process elements, we found some evidence that they do not share the same neutron exposure parameter. The exact mechanism controlling this difference is still not clear. As a by-product of this analysis we identify two normal red giants misclassified as mild barium stars. The relevance of this finding is discussed. Concerning the suggested nucleosynthetic effects possibly related to the s-process, for elements like Cu, Mn, V and Sc, we found no evidence for an anomalous behavior in any of the s-process enriched stars analyzed here. However, further work is still needed since a clear [Cu/Fe] vs. [Ba/Fe] anticorrelation exists for other s-process enriched objects. Observations collected at ESO, La Silla, Chile, within the ON/ESO agreements. Tables 8-10 are only

  1. CH Stars and Barium Stars

    NASA Astrophysics Data System (ADS)

    Bond, H.; Sion, E.; Murdin, P.

    2000-11-01

    The classical barium (or `Ba II') stars are RED GIANT STARS whose spectra show strong absorption lines of barium, strontium and certain other heavy elements, as well as strong features due to carbon molecules. Together with the related class of CH stars, the Ba II stars were crucial in establishing the existence of neutron-capture reactions in stellar interiors that are responsible for the synt...

  2. Barium light source method and apparatus

    NASA Technical Reports Server (NTRS)

    Curry, John J. (Inventor); MacDonagh-Dumler, Jeffrey (Inventor); Anderson, Heidi M. (Inventor); Lawler, James E. (Inventor)

    2002-01-01

    Visible light emission is obtained from a plasma containing elemental barium including neutral barium atoms and barium ion species. Neutral barium provides a strong green light emission in the center of the visible spectrum with a highly efficient conversion of electrical energy into visible light. By the selective excitation of barium ionic species, emission of visible light at longer and shorter wavelengths can be obtained simultaneously with the green emission from neutral barium, effectively providing light that is visually perceived as white. A discharge vessel contains the elemental barium and a buffer gas fill therein, and a discharge inducer is utilized to induce a desired discharge temperature and barium vapor pressure therein to produce from the barium vapor a visible light emission. The discharge can be induced utilizing a glow discharge between electrodes in the discharge vessel as well as by inductively or capacitively coupling RF energy into the plasma within the discharge vessel.

  3. Solvothermal synthesis and characterization of two inorganic-organic hybrid materials based on barium.

    PubMed

    Abdollahian, Yashar; Hauser, Jesse L; Rogow, David L; Oliver, Allen G; Oliver, Scott R J

    2012-10-28

    Two metal-organic frameworks containing barium were synthesized hydrothermally and investigated for their catalytic properties. Ba(2)F(2)[O(3)SC(2)H(4)SO(3)] has barium fluoride layers linked by organic 1,2-ethanedisulfonate molecules. Ba[O(3)SC(2)H(4)SO(3)] has discrete barium centers arranged in layers and connected covalently by ethanedisulfonate bridges. Thermogravimetric analysis showed that Ba(2)F(2)[O(3)SC(2)H(4)SO(3)] is stable to ca. 325 °C and Ba[O(3)SC(2)H(4)SO(3)] to ca. 375 °C. These materials expand the metal-organic frameworks available for group II metals bound to organodisulfonate linkers and are potentially useful for a range of heterogeneous acid catalysis reactions.

  4. Aberration control in 4Pi nanoscopy: definitions, properties, and applications (Conference Presentation)

    NASA Astrophysics Data System (ADS)

    Hao, Xiang; Allgeyer, Edward S.; Velasco, Mary Grace M.; Booth, Martin J.; Bewersdorf, Joerg

    2016-03-01

    The development of fluorescence microscopy, which allows live-cell imaging with high labeling specificity, has made the visualization of cellular architecture routine. However, for centuries, the spatial resolution of optical microscopy was fundamentally limited by diffraction. The past two decades have seen a revolution in far-field optical nanoscopy (or "super-resolution" microscopy). The best 3D resolution is achieved by optical nanoscopes like the isoSTED or the iPALM/4Pi-SMS, which utilize two opposing objective lenses in a coherent manner. These system are, however, also more complex and the required interference conditions demand precise aberration control. Our research involves developing novel adaptive optics techniques that enable high spatial and temporal resolution imaging for biological applications. In this talk, we will discuss how adaptive optics can enhance dual-objective lens nanoscopes. We will demonstrate how adaptive optics devices provide unprecedented freedom to manipulate the light field in isoSTED nanoscopy, allow to realize automatic beam alignment, suppress the inherent side-lobes of the point-spread function, and dynamically compensate for sample-induced aberrations. We will present both the theoretical groundwork and the experimental confirmations.

  5. The data acquisition and control system for the 4{pi} detector CHIMERA

    SciTech Connect

    Aiello, S.; Anzalone, A.; Cardella, G.

    1998-08-01

    CHIMERA (Charged Heavy Ions Mass and Energy Resolving Array), a new 4{pi} detector for charged particles is under development at various sites of the Istituto Nazionale di Fisica Nucleare. This paper describes the new data acquisition system built to handle the signals coming out from the detector with a rate up to 1 kHz on almost 5000 electronic channels. The required average throughput for the system is in the order of the 1 MB/s. The used converters allow double-range conversion on 15 bits, in less than 50 {micro}s for all the 64 channels. The FDL link connects the different VME 9U crates performing a programmable hardware readout with a rate up to 100 MB/s. It uses a fast hardware protocol (Sparse Data Scan) to read the data buffers and send them to a FIC 8243 CPU board. A FIC 8243 dual-processor board forwards data (through Ethernet) to the analysis station (266 Mhz Digital AlphaStation or Sun Sparcstation). A DLT (Digital Linear Tape) unit connected to analysis station is used to store data. The new data acquisition system has been tested under beam conditions at the Laboratorio Nazionale del Sud (Catania, Italy) and at GANIL (Caen, France).

  6. A Comparison of 2pi and 4pi Photometric Testing of Directional and Omnidirectional Sources in an Integrating Sphere

    SciTech Connect

    Richman, Eric E.; Merzouk, Massine B.

    2014-06-12

    A Comparison of 2pi and 4pi Photometric Testing of Directional and Omnidirectional Sources in an Integrating Sphere. These data will help determine if differences in methods should be addresed in test methods specifically for LED products but applicable to other technologies as well

  7. Fluoride and Water (For Parents)

    MedlinePlus

    ... Your 1- to 2-Year-Old Fluoride and Water KidsHealth > For Parents > Fluoride and Water A A ... to 19-year-olds continue Fluoride and the Water Supply For more than 60 years, water fluoridation ...

  8. Fluoride and Water (For Parents)

    MedlinePlus

    ... Your 1- to 2-Year-Old Fluoride and Water KidsHealth > For Parents > Fluoride and Water Print A ... to 19-year-olds continue Fluoride and the Water Supply For more than 60 years, water fluoridation ...

  9. Interaction between Barium Oxide and Barium Containing Chloride Melt

    NASA Astrophysics Data System (ADS)

    Nikolaeva, Elena V.; Zakiryanova, Irina D.; Korzun, Iraida V.; Bovet, Andrey L.; Antonov, Boris D.

    2015-05-01

    Thermal analysis was applied to determine the liquidus temperatures in the NaCl-KCl-BaCl2-BaO system, with BaO concentration varied from 0 to 6 mole%. The temperature dependence of the BaO solubility in the NaCl-KCl-BaCl2 eutectic melt was investigated; the thermodynamic parameters of BaO dissolution were calculated. The caloric effects of melting of the NaCl-KCl-BaCl2 eutectic with barium oxide and barium oxychloride additions were studied. The type, morphology, and composition of oxychloride ionic groupings in the melt were determined in situ using Raman spectroscopy.

  10. 75 FR 33824 - Barium Chloride From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-15

    ... COMMISSION Barium Chloride From China Determination On the basis of the record\\1\\ developed in the subject... order on barium chloride from China would be likely to lead to continuation or recurrence of material... Barium Chloride from China: Investigation No. 731-TA-149 (Third Review). By order of the...

  11. How Does Fluoride Work?

    MedlinePlus

    ... Work? A A A There's fluoride in your toothpaste and even in your water. But how does ... enamel from plaque and sugars. By using fluoride toothpaste, for instance, everyone can enjoy some cavity protection. ...

  12. Structural features of alkali and barium aluminofluorophosphate glasses studied by IR spectroscopy

    SciTech Connect

    Urusovskaya, L.N.; Smirnova, E.V.

    1995-03-01

    IR reflection spectra of the Al(PO{sub 3}){sub 3}-MeF{sub x} glasses (Me=Li, Na, K, Ba) with the maximum content of fluoride varied for each specific glass within certain concentration limits are considered. Analysis of the spectra for glasses obtained upon variation in the content of alkali metal fluoride introduced into these glasses has demonstrated that the increase in the MeF{sub x} content leads to breaking the chain groupings and forming the [PO{sub 3}F]{sup 2-} groups, whereas the rise in concentration of barium fluoride in the Al(PO{sub 3}){sub 3}-BaF{sub 2} glasses brings about the stabilization of the chain structures.

  13. High index fluoride materials for 193nm immersion lithography

    NASA Astrophysics Data System (ADS)

    Nawata, T.; Inui, Y.; Masada, I.; Nishijima, E.; Satoh, H.; Fukuda, T.

    2006-03-01

    We tried to investigate various kinds of metal fluoride materials which have higher gravity than CaF II and cubic crystal system, and we found out barium lithium fluoride (BaLiF 3) and potassium yttrium fluoride (KY 3F 10) as candidates for the last lens material. We have developed unique Czochralski (CZ) machines and techniques for the growth of large calcium fluoride single crystals. And we applied these technologies to the growth of fluoride high index materials. We have succeeded to grow the large BaLiF 3 single crystal with 120mm in diameter and a KY 3F 10 single crystal, and measured their basic properties such as refractive index, VUV transmittance, birefringence, and so on. As a result of our basic research, we found out that BaLiF 3 single crystal is transparent at VUV region, and the refractive index at 193nm is 1.64, and KY 3F 10 single crystal has the index of 1.59 at the wavelength of 193nm which is slightly higher than fused silica. We expect that these fluoride high index materials are useful for the last lens material of the next generation immersion lithography.

  14. Study of Nuclei far From Stability by Using the CHIMERA 4{pi} Detector and Radioactive Beams at LNS

    SciTech Connect

    Cardella, G.; De Filippo, E.; Pagano, A.; Papa, M.; Pirrone, S.; Verde, G.; Amorini, F.; Anzalone, A.; Maiolino, C.; Auditore, L.; Loria, D.; Trifiro, A.; Trimarchi, M.; Cavallaro, S.; Lombardo, I.; Porto, F.; Rizzo, F.; Russotto, P.; Chatterjee, M. B.; Geraci, E.

    2009-08-26

    At LNS are available radioactive beams at tandem and intermediate energies provided respectively by the EXCYT and by the fragmentation FRIBS facilities. Using these beams, and the 4{pi} detector CHIMERA, we want to study excitation and decay of resonances in light exotic nuclei populated with pick-up stripping and other reaction mechanisms. Some preliminary results obtained with stable and unstable beams are reported.

  15. Barium hexaferrite (M-phase) exhibiting superstructure

    SciTech Connect

    Ganapathi, L.; Gopalakrishnan, J.; Rao, C.N.R.

    1984-05-01

    Barium hexaferrite (M-phase) prepared by the flux method is found to exhibit a ..sqrt..3a x ..sqrt..3a superstructure similar to barium hexaaluminate. Morgan and Shaw as well as Iyi et al have recently reported the formation of a barium-rich phase of barium hexaaluminate possessing a ..sqrt..3a x ..sqrt..3a superstructure of the magnetoplumbite structure. In view of the similarities between the layer structures of ..beta..-aluminas and the corresponding ferrites the authors have been carrying out electron microscopic investigations of potassium ..beta..-alumina and BaA1/sub 12/O/sub 19/ along with ferrites of similar compositions. They have obtained electron diffraction patterns of barium hexaaluminate identical to those obtained by Morgan and Shaw and Iyi et al, but more interestingly, they have found a phase of barium hexaferrite (M-phase) exhibiting the ..sqrt..3a x ..sqrt..3a superstructure.

  16. Fluoride and Oral Health.

    PubMed

    O'Mullane, D M; Baez, R J; Jones, S; Lennon, M A; Petersen, P E; Rugg-Gunn, A J; Whelton, H; Whitford, G M

    2016-06-01

    The discovery during the first half of the 20th century of the link between natural fluoride, adjusted fluoride levels in drinking water and reduced dental caries prevalence proved to be a stimulus for worldwide on-going research into the role of fluoride in improving oral health. Epidemiological studies of fluoridation programmes have confirmed their safety and their effectiveness in controlling dental caries. Major advances in our knowledge of how fluoride impacts the caries process have led to the development, assessment of effectiveness and promotion of other fluoride vehicles including salt, milk, tablets, toothpaste, gels and varnishes. In 1993, the World Health Organization convened an Expert Committee to provide authoritative information on the role of fluorides in the promotion of oral health throughout the world (WHO TRS 846, 1994). This present publication is a revision of the original 1994 document, again using the expertise of researchers from the extensive fields of knowledge required to successfully implement complex interventions such as the use of fluorides to improve dental and oral health. Financial support for research into the development of these new fluoride strategies has come from many sources including government health departments as well as international and national grant agencies. In addition, the unique role which industry has played in the development, formulation, assessment of effectiveness and promotion of the various fluoride vehicles and strategies is noteworthy. This updated version of 'Fluoride and Oral Health' has adopted an evidence-based approach to its commentary on the different fluoride vehicles and strategies and also to its recommendations. In this regard, full account is taken of the many recent systematic reviews published in peer reviewed literature.

  17. The problem of the barium stars

    NASA Technical Reports Server (NTRS)

    Bohm-Vitense, E.; Nemec, J.; Proffitt, C.

    1984-01-01

    Ultraviolet observations of barium stars and other cool stars with peculiar element abundances are reported. Those observations attempted to find hot white dwarf companions. Among six real barium stars studied, only Zeta Cap was found to have a white dwarf companion. Among seven mild, or marginal, barium stars studied, at least three were found to have hot subluminous companions. It is likely that all of them have white dwarf companions.

  18. Barium Depletion in Hollow Cathode Emitters

    NASA Technical Reports Server (NTRS)

    Polk, James E.; Capece, Angela M.; Mikellides, Ioannis G.; Katz, Ira

    2009-01-01

    The effect of tungsten erosion, transport and redeposition on the operation of dispenser hollow cathodes was investigated in detailed examinations of the discharge cathode inserts from an 8200 hour and a 30,352 hour ion engine wear test. Erosion and subsequent re-deposition of tungsten in the electron emission zone at the downstream end of the insert reduces the porosity of the tungsten matrix, preventing the ow of barium from the interior. This inhibits the interfacial reactions of the barium-calcium-aluminate impregnant with the tungsten in the pores. A numerical model of barium transport in the internal xenon discharge plasma shows that the barium required to reduce the work function in the emission zone can be supplied from upstream through the gas phase. Barium that flows out of the pores of the tungsten insert is rapidly ionized in the xenon discharge and pushed back to the emitter surface by the electric field and drag from the xenon ion flow. This barium ion flux is sufficient to maintain a barium surface coverage at the downstream end greater than 0.6, even if local barium production at that point is inhibited by tungsten deposits. The model also shows that the neutral barium pressure exceeds the equilibrium vapor pressure of the impregnant decomposition reaction over much of the insert length, so the reactions are suppressed. Only a small region upstream of the zone blocked by tungsten deposits is active and supplies the required barium. These results indicate that hollow cathode failure models based on barium depletion rates in vacuum dispenser cathodes are very conservative.

  19. Fluorides and non-fluoride remineralization systems.

    PubMed

    Amaechi, Bennett T; van Loveren, Cor

    2013-01-01

    Caries develops when the equilibrium between de- and remineralization is unbalanced favoring demineralization. De- and remineralization occur depending on the degree of saturation of the interstitial fluids with respect to the tooth mineral. This equilibrium is positively influenced when fluoride, calcium and phosphate ions are added favoring remineralization. In addition, when fluoride is present, it will be incorporated into the newly formed mineral which is then less soluble. Toothpastes may contain fluoride and calcium ions separately or together in various compounds (remineralization systems) and may therefore reduce demineralization and promote remineralization. Formulating all these compounds in one paste may be challenging due to possible premature calcium-fluoride interactions and the low solubility of CaF2. There is a large amount of clinical evidence supporting the potent caries preventive effect of fluoride toothpastes indisputably. The amount of clinical evidence of the effectiveness of the other remineralization systems is far less convincing. Evidence is lacking for head to head comparisons of the various remineralization systems.

  20. Calcium fluoride window mounting

    NASA Astrophysics Data System (ADS)

    Berger, D. Douglas

    1982-10-01

    A technique has been developed for joining a large calcium fluoride crystal to a stainless-steel flange by means of a silver transition ring. The process involves both vacuum brazing using a copper-silver alloy and air brazing using silver chloride. This paper describes the procedure used in fabricating a high-vacuum leak-tight calcium fluoride window assembly.

  1. PRODUCTION OF THORIUM FLUORIDE

    DOEpatents

    Zachariasen, W.H.

    1959-08-11

    A process is presented for producing anhydrous thorium fluoride comprising the step of contacting a saturated aqueous solution of thorium nitrate with an aqueous solution of hydrofluoric acid having a concentration of about 45 to 50% by weight at a temperature above 70 deg C whereby anhydrous thorium fluoride precipitates.

  2. Processing science of barium titanate

    NASA Astrophysics Data System (ADS)

    Aygun, Seymen Murat

    Barium titanate and barium strontium titanate thin films were deposited on base metal foils via chemical solution deposition and radio frequency magnetron sputtering. The films were processed at elevated temperatures for densification and crystallization. Two unifying research goals underpin all experiments: (1) To improve our fundamental understanding of complex oxide processing science, and (2) to translate those improvements into materials with superior structural and electrical properties. The relationships linking dielectric response, grain size, and thermal budget for sputtered barium strontium titanate were illustrated. (Ba 0.6Sr0.4)TiO3 films were sputtered on nickel foils at temperatures ranging between 100-400°C. After the top electrode deposition, the films were co-fired at 900°C for densification and crystallization. The dielectric properties were observed to improve with increasing sputter temperature reaching a permittivity of 1800, a tunability of 10:1, and a loss tangent of less than 0.015 for the sample sputtered at 400°C. The data can be understood using a brick wall model incorporating a high permittivity grain interior with low permittivity grain boundary. However, this high permittivity value was achieved at a grain size of 80 nm, which is typically associated with strong suppression of the dielectric response. These results clearly show that conventional models that parameterize permittivity with crystal diameter or film thickness alone are insufficiently sophisticated. Better models are needed that incorporate the influence of microstructure and crystal structure. This thesis next explores the ability to tune microstructure and properties of chemically solution deposited BaTiO3 thin films by modulation of heat treatment thermal profiles and firing atmosphere composition. Barium titanate films were deposited on copper foils using hybrid-chelate chemistries. An in-situ gas analysis process was developed to probe the organic removal and the

  3. Indium fluoride glass fibers

    NASA Astrophysics Data System (ADS)

    Saad, Mohammed

    2012-03-01

    Fluoride glasses are the only material that transmit light from ultraviolet to mid-infrared and can be drawn into industrial optical fibers. The mechanical and optical properties of new indium fluoride glass fibers have been investigated. Multimode fiber 190 microns, has very high mechanical strength greater than 100 kpsi and optical loss as low as 45 dB/km between 2 and 4 microns. Unlike chalcogenide glass fibers, indium fluoride fiber has a wide transmission window from 0.3 to 5.5 microns without any absorption peak. Indium fluoride glass fibers are the technology of choice for all application requiring transmission up to 5 micron such as infrared contour measure (IRCM) and chemical sensing. Furthermore, Indium fluoride glasses have low phonon energy and can be heavily doped and co-doped whit rare-earth elements. Therefore they are very promising candidates for infrared fiber lasers.

  4. Barium granuloma of the transverse colon.

    PubMed Central

    McKee, P. H.; Cameron, C. H.

    1978-01-01

    A case of barium sulphate granuloma of the transverse colon following gunshot wounds to the abdomen has been described. Scanning electron microscopy with electron probe microanalysis was used to confirm the presence of barium sulphate and the absence of lead or other elements related to the gunshot wounds. Images Fig. 1 Fig. 2 Fig. 3 Fig. 4 PMID:740599

  5. Casting of Halide and Fluoride Alloys for Laser Windows

    DTIC Science & Technology

    1974-07-15

    mechanism leads to an inverse square root dependence of fracture strength on grain size. Since CaF2, SrFp and BaFp all exhibit at least microplastic ...flaws or microplasticity is the strength limiting factor is not known. 4.2.2 Solid-solution strengthening 4.2.2. 1 General If fracture in these...Temperature Microplasticity in SrF2 Single Crystals, " J. Appl. Phys. 41_(4) 1871 (1970). 12. T.S. Liu and C.H. Li, " Plasticity of Barium Fluoride

  6. Fluoride glass starting materials - Characterization and effects of thermal treatment

    NASA Technical Reports Server (NTRS)

    Chen, William; Dunn, Bruce; Shlichta, Paul; Neilson, George F.; Weinberg, Michael C.

    1987-01-01

    The production of heavy metal fluoride (HMF) glasses, and the effects of thermal treatments on the HMF glasses are investigated. ZrF4, BaF2, AlF3, LaF3, and NaF were utilized in the synthesis of zirconium-barium-lanthanum-aluminum-sodium fluoride glass. The purity of these starting materials, in particular ZrF4, is evaluated using XRD analysis. The data reveal that low temperature heating of ZrF4-H2O is effective in removing the water of hydration, but causes the production of ZrF4 and oxyfluorides; however, dehydration followed by sublimation results in the production of monoclinic ZrFe without water or oxyfluoride contaminants.

  7. Fluoride in diet

    MedlinePlus

    ... broken through the gums have changes in the enamel that covers the teeth. Faint white lines or ... regarding fluoride intake from reconstituted infant formula and enamel fluorosis: a report of the American Dental Association ...

  8. Other Fluoride Products

    MedlinePlus

    ... relatively infrequent, generally at 3 to 12–month intervals, fluoride gel poses little risk for dental fluorosis, ... many hours. Varnishes must be reapplied at regular intervals with at least 2 applications per year required ...

  9. How Does Fluoride Work?

    MedlinePlus

    ... Fluoride is a natural element found in the earth's crust as well as in water and air. ... Activity: Teeth What Are Dentures? Contact Us Print Resources Send to a Friend Permissions Guidelines About KidsHealth ...

  10. Radium/Barium Waste Project

    SciTech Connect

    McDowell, Allen K.; Ellefson, Mark D.; McDonald, Kent M.

    2015-06-25

    The treatment, shipping, and disposal of a highly radioactive radium/barium waste stream have presented a complex set of challenges requiring several years of effort. The project illustrates the difficulty and high cost of managing even small quantities of highly radioactive Resource Conservation and Recovery Act (RCRA)-regulated waste. Pacific Northwest National Laboratory (PNNL) research activities produced a Type B quantity of radium chloride low-level mixed waste (LLMW) in a number of small vials in a facility hot cell. The resulting waste management project involved a mock-up RCRA stabilization treatment, a failed in-cell treatment, a second, alternative RCRA treatment approach, coordinated regulatory variances and authorizations, alternative transportation authorizations, additional disposal facility approvals, and a final radiological stabilization process.

  11. Process for converting magnesium fluoride to calcium fluoride

    DOEpatents

    Kreuzmann, A.B.; Palmer, D.A.

    1984-12-21

    This invention is a process for the conversion of magnesium fluoride to calcium fluoride whereby magnesium fluoride is decomposed by heating in the presence of calcium carbonate, calcium oxide or calcium hydroxide. Magnesium fluoride is a by-product of the reduction of uranium tetrafluoride to form uranium metal and has no known commercial use, thus its production creates a significant storage problem. The advantage of this invention is that the quality of calcium fluoride produced is sufficient to be used in the industrial manufacture of anhydrous hydrogen fluoride, steel mill flux or ceramic applications.

  12. The future of water fluoridation and other systemic fluorides.

    PubMed

    Horowitz, H S

    1990-02-01

    School and community water fluoridation, salt fluoridation, and use of dietary fluoride supplements have abundant scientific support as effective caries-preventive methods. Because caries has declined greatly in many developed countries from use of topical fluorides, the absolute caries reduction will be considerably smaller when systemic fluoride methods are implemented now than it was 20 to 40 years ago. For countries with most of the population living in cities with communal water supplies, community fluoridation is the most logical approach from the standpoints of cost-effectiveness and total caries-preventive impact. In countries with a mostly rural population without central water supplies, salt fluoridation is more practical. Dietary fluoride supplements can be recommended only for regions where neither water fluoridation nor salt fluoridation is possible, or as a temporary measure. Although divergent views exist concerning the relative caries-preventive effects of pre-eruptive and post-eruptive fluoride administration, the effectiveness of systemic fluoride methods for preventing dental caries remains unchallenged. Persuasive scientific and public health arguments exist to justify implementing and sustaining their use. The future of these methods will be influenced by the findings of new clinical and epidemiological research. Social, political, economic, and educational factors will be of equal, if not greater, importance. Perceptions of the current severity of dental caries as a health problem and of risks associated with preventing the problem may affect the future uses of systemic fluorides more than will recommendations of scientists.

  13. 75 FR 20625 - Barium Chloride From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-20

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Barium Chloride From China AGENCY: United States International Trade Commission. ACTION: Revised schedule for the subject review. DATES: Effective Date: April 9, 2010. FOR FURTHER INFORMATION CONTACT:...

  14. Acute barium nitrate intoxication treated by hemodialysis.

    PubMed

    Bahlmann, H; Lindwall, R; Persson, H

    2005-01-01

    A 22-year-old male was admitted to hospital with diarrhea and vomiting, cardiac arrhythmias, severe hypokalemia and gradual onset of muscular weakness. A potassium infusion was started, but for several hours serum potassium remained low. Evidence of toxic ingestion was initially lacking. When it became clear -- after a considerable delay -- that the patient had ingested barium nitrate, hemodialysis was started. This resulted in rapid clinical improvement with correction of hypokalemia and restored muscular function. Intoxication with barium causes hypokalemia, arrhythmias, muscular weakness and paralysis, often requiring respiratory support. This patient presented with symptoms typical of severe barium intoxication, non-responsive to potassium supplementation. There are few published reports on the use of hemodialysis in barium poisoning. This case confirms the possible benefit of hemodialysis in severe cases, where potassium supplementation alone is insufficient.

  15. Barium Isotopes in Single Presolar Grains

    NASA Technical Reports Server (NTRS)

    Pellin, M. J.; Davis, A. M.; Savina, M. R.; Kashiv, Y.; Clayton, R. N.; Lewis, R. S.; Amari, S.

    2001-01-01

    Barium isotopic compositions of single presolar grains were measured by laser ablation laser resonant ionization mass spectrometry and the implications of the data for stellar processes are discussed. Additional information is contained in the original extended abstract.

  16. Fluoride content of infant foods.

    PubMed

    Steele, Jaime L; Martinez-Mier, E Angeles; Sanders, Brian J; Jones, James E; Jackson, Richard D; Soto-Rojas, Armando E; Tomlin, Angela M; Eckert, George J

    2014-01-01

    Excessive fluoride consumption during the first 2 years of life is associated with an increased risk of dental fluorosis. Estimates of fluoride intake from various sources may aid in determining a child's risk for developing fluorosis. This study sought to assess the fluoride content of commercially available foods for infants, and to guide dentists who are advising parents of young children about fluoride intake. Three samples each of 20 different foods (including fruits and vegetables, as well as chicken, turkey, beef/ham, and vegetarian dinners) from 3 manufacturers were analyzed (in duplicate) for their fluoride content. Among the 360 samples tested, fluoride concentration ranged from 0.007-4.13 μg fluoride/g food. All foods tested had detectable amounts of fluoride. Chicken products had the highest mean levels of fluoride, followed by turkey products. Consuming >1 serving per day of the high fluoride concentration products in this study would place children over the recommended daily fluoride intake. Fluoride from infant foods should be taken into account when determining total daily fluoride intake.

  17. Permeability and fluoride release of lining materials containing amine fluorides.

    PubMed

    Nordbö, H; Eriksen, H M

    1976-11-01

    The addition of amine fluorides to a copal recin (Copalite) and a chlorine caoutchouc varnish (Pergut S-40) has been studied. The permeability of Copalite films was only slightly increased whereas the excellent film-forming qualities of Pergut S-40 were destroyed by the addition of fluorides. A high fluoride release was found initially from test films of the materials but within 2-3 weeks a decrease to very low fluoride levels was observed.

  18. Thermochemical hydrogen production via a cycle using barium and sulfur - Reaction between barium sulfide and water

    NASA Technical Reports Server (NTRS)

    Ota, K.; Conger, W. L.

    1977-01-01

    The reaction between barium sulfide and water, a reaction found in several sulfur based thermochemical cycles, was investigated kinetically at 653-866 C. Gaseous products were hydrogen and hydrogen sulfide. The rate determining step for hydrogen formation was a surface reaction between barium sulfide and water. An expression was derived for the rate of hydrogen formation.

  19. Sulphate removal from sodium sulphate-rich brine and recovery of barium as a barium salt mixture.

    PubMed

    Vadapalli, Viswanath R K; Zvimba, John N; Mulopo, Jean; Motaung, Solly

    2013-01-01

    Sulphate removal from sodium sulphate-rich brine using barium hydroxide and recovery of the barium salts has been investigated. The sodium sulphate-rich brine treated with different dosages of barium hydroxide to precipitate barium sulphate showed sulphate removal from 13.5 g/L to less than 400 mg/L over 60 min using a barium to sulphate molar ratio of 1.1. The thermal conversion of precipitated barium sulphate to barium sulphide achieved a conversion yield of 85% using coal as both a reducing agent and an energy source. The recovery of a pure mixture of barium salts from barium sulphide, which involved dissolution of barium sulphide and reaction with ammonium hydroxide resulted in recovery of a mixture of barium carbonate (62%) and barium hydroxide (38%), which is a critical input raw material for barium salts based acid mine drainage (AMD) desalination technologies. Under alkaline conditions of this barium salt mixture recovery process, ammonia gas is given off, while hydrogen sulfide is retained in solution as bisulfide species, and this provides basis for ammonium hydroxide separation and recovery for reuse, with hydrogen sulfide also recoverable for further industrial applications such as sulfur production by subsequent stripping.

  20. MOLTEN FLUORIDE NUCLEAR REACTOR FUEL

    DOEpatents

    Barton, C.J.; Grimes, W.R.

    1960-01-01

    Molten-salt reactor fuel compositions consisting of mixtures of fluoride salts are reported. In its broadest form, the composition contains an alkali fluoride such as sodium fluoride, zirconium tetrafluoride, and a uranium fluoride, the latter being the tetrafluoride or trifluoride or a mixture of the two. An outstanding property of these fuel compositions is a high coeffieient of thermal expansion which provides a negative temperature coefficient of reactivity in reactors in which they are used.

  1. Chemical abundances and kinematics of barium stars

    NASA Astrophysics Data System (ADS)

    de Castro, D. B.; Pereira, C. B.; Roig, F.; Jilinski, E.; Drake, N. A.; Chavero, C.; Sales Silva, J. V.

    2016-07-01

    In this paper, we present an homogeneous analysis of photospheric abundances based on high-resolution spectroscopy of a sample of 182 barium stars and candidates. We determined atmospheric parameters, spectroscopic distances, stellar masses, ages, luminosities and scaleheight, radial velocities, abundances of the Na, Al, α-elements, iron-peak elements, and s-process elements Y, Zr, La, Ce, and Nd. We employed the local thermodynamic equilibrium model atmospheres of Kurucz and the spectral analysis code MOOG. We found that the metallicities, the temperatures and the surface gravities for barium stars cannot be represented by a single Gaussian distribution. The abundances of α-elements and iron peak elements are similar to those of field giants with the same metallicity. Sodium presents some degree of enrichment in more evolved stars that could be attributed to the NeNa cycle. As expected, the barium stars show overabundance of the elements created by the s-process. By measuring the mean heavy-element abundance pattern as given by the ratio [s/Fe], we found that the barium stars present several degrees of enrichment. We also obtained the [hs/ls] ratio by measuring the photospheric abundances of the Ba-peak and the Zr-peak elements. Our results indicated that the [s/Fe] and the [hs/ls] ratios are strongly anticorrelated with the metallicity. Our kinematical analysis showed that 90 per cent of the barium stars belong to the thin disc population. Based on their luminosities, none of the barium stars are luminous enough to be an asymptotic giant branch star, nor to become self-enriched in the s-process elements. Finally, we determined that the barium stars also follow an age-metallicity relation.

  2. Constraining the oceanic barium cycle with stable barium isotopes

    NASA Astrophysics Data System (ADS)

    Cao, Zhimian; Siebert, Christopher; Hathorne, Ed C.; Dai, Minhan; Frank, Martin

    2016-01-01

    The distribution of barium (Ba) concentrations in seawater resembles that of nutrients and Ba has been widely used as a proxy of paleoproductivity. However, the exact mechanisms controlling the nutrient-like behavior, and thus the fundamentals of Ba chemistry in the ocean, have not been fully resolved. Here we present a set of full water column dissolved Ba (DBa) isotope (δ137BaDBa) profiles from the South China Sea and the East China Sea that receives large freshwater inputs from the Changjiang (Yangtze River). We find pronounced and systematic horizontal and depth dependent δ137BaDBa gradients. Beyond the river influence characterized by generally light signatures (0.0 to + 0.3 ‰), the δ137BaDBa values in the upper water column are significantly higher (+ 0.9 ‰) than those in the deep waters (+ 0.5 ‰). Moreover, δ137BaDBa signatures are essentially constant in the entire upper 100 m, in which dissolved silicon isotopes are fractionated during diatom growth resulting in the heaviest isotopic compositions in the very surface waters. Combined with the decoupling of DBa concentrations and δ137BaDBa from the concentrations of nitrate and phosphate this implies that the apparent nutrient-like fractionation of Ba isotopes in seawater is primarily induced by preferential adsorption of the lighter isotopes onto biogenic particles rather than by biological utilization. The subsurface δ137BaDBa distribution is dominated by water mass mixing. The application of stable Ba isotopes as a proxy for nutrient cycling should therefore be considered with caution and both biological and physical processes need to be considered. Clearly, however, Ba isotopes show great potential as a new tracer for land-sea interactions and ocean mixing processes.

  3. Small molecule fluoride toxicity agonists.

    PubMed

    Nelson, James W; Plummer, Mark S; Blount, Kenneth F; Ames, Tyler D; Breaker, Ronald R

    2015-04-23

    Fluoride is a ubiquitous anion that inhibits a wide variety of metabolic processes. Here, we report the identification of a series of compounds that enhance fluoride toxicity in Escherichia coli and Streptococcus mutans. These molecules were isolated by using a high-throughput screen (HTS) for compounds that increase intracellular fluoride levels as determined via a fluoride riboswitch reporter fusion construct. A series of derivatives were synthesized to examine structure-activity relationships, leading to the identification of compounds with improved activity. Thus, we demonstrate that small molecule fluoride toxicity agonists can be identified by HTS from existing chemical libraries by exploiting a natural fluoride riboswitch. In addition, our findings suggest that some molecules might be further optimized to function as binary antibacterial agents when combined with fluoride.

  4. Small Molecule Fluoride Toxicity Agonists

    PubMed Central

    Nelson1, James W.; Plummer, Mark S.; Blount, Kenneth F.; Ames, Tyler D.; Breaker, Ronald R.

    2015-01-01

    SUMMARY Fluoride is a ubiquitous anion that inhibits a wide variety of metabolic processes. Here we report the identification of a series of compounds that enhance fluoride toxicity in Escherichia coli and Streptococcus mutans. These molecules were isolated by using a high-throughput screen (HTS) for compounds that increase intracellular fluoride levels as determined via a fluoride riboswitch-reporter fusion construct. A series of derivatives were synthesized to examine structure-activity relationships, leading to the identification of compounds with improved activity. Thus, we demonstrate that small molecule fluoride toxicity agonists can be identified by HTS from existing chemical libraries by exploiting a natural fluoride riboswitch. In addition, our findings suggest that some molecules might be further optimized to function as binary antibacterial agents when combined with fluoride. PMID:25910244

  5. Heavy Metal Fluoride Glasses.

    DTIC Science & Technology

    1987-04-01

    relatively low refractive Indices in the visible range of about 1.5-1.9 and fairly good chemical resistance towards water and weak acids. Their...particularly interesting to compare with crystalline fluorides (Refs. 25, 37) such as 7800 spinel-type Li2NiF4 ; 7700 rutile-type NiF2 ; 7500 perovskite-type

  6. Ferrimyoglobin-Fluoride.

    ERIC Educational Resources Information Center

    Russo, Steven O.; Hanania, George I. H.

    1990-01-01

    Described is an experiment which is designed to investigate the reaction of the protein ferrimyoglobin with fluoride. The activity uses readily available apparatus and the technique of optical absorbance for measurement of concentrations. Experimental design, procedures, and treatment of the equilibrium data are detailed. (CW)

  7. Fluorine (soluble fluoride)

    Integrated Risk Information System (IRIS)

    Fluorine ( soluble fluoride ) ; CASRN 7782 - 41 - 4 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for No

  8. Barium iodide single-crystal scintillator detectors

    NASA Astrophysics Data System (ADS)

    Cherepy, Nerine J.; Hull, Giulia; Niedermayr, Thomas R.; Drobshoff, Alexander; Payne, Stephen A.; Roy, Utpal N.; Cui, Yunlong; Bhattacharaya, Ajanta; Harrison, Melissa; Guo, Mingsheng; Groza, Michael; Burger, Arnold

    2007-09-01

    We find that the high-Z crystal Barium Iodide is readily growable by the Bridgman growth technique and is less prone to crack compared to Lanthanum Halides. We have grown Barium Iodide crystals: undoped, doped with Ce 3+, and doped with Eu 2+. Radioluminescence spectra and time-resolved decay were measured. BaI II(Eu) exhibits luminescence from both Eu 2+ at 420 nm (~450 ns decay), and a broad band at 550 nm (~3 μs decay) that we assign to a trapped exciton. The 550 nm luminescence decreases relative to the Eu 2+ luminescence when the Barium Iodide is zone refined prior to crystal growth. We also describe the performance of BaI II(Eu) crystals in experimental scintillator detectors.

  9. Improved spectrophotometric analysis of barium styphnate

    SciTech Connect

    Brown, N E; Blasi, J A

    1983-01-01

    A spectrophotometric procedure to determine the purity of barium styphnate monohydrate based upon the absorbance of the styphnate ion at 326 and 413.3 nm has been developed. The purity is determined by comparing the absorbance of the styphnate ion in barium styphnate and in styphnic acid. Our investigation has shown that the molar absorptivity and lambda maxima of the styphnate ion are quite pH dependent; therefore, the pH is buffered to 6.8 to 7.0 with ammonium acetate. Under these conditions the molar absorptivity is 1.6 x 10/sup 4/ L/mol-cm. Analyses following the procedure in the Navy specification WS13444A using water were found to give low molar absorptivities (1.3 x 10/sup 4/ L/mol-cm) for the styphnic acid calibration resulting in erroneous values for barium styphnate purity.

  10. Surface treatment of barium gallogermanate laser glass

    NASA Astrophysics Data System (ADS)

    Yang, Gang; Qian, Qi; Yang, Zhongmin

    2011-01-01

    The surface of barium gallogermanate glass is modified through HCl solution etching to remove the surface defects and contaminations. The etching process and mechanism for barium gallogermanate glass in hydrochloric acid are investigated, and its optimum conditions are determined. However, the HCl etching induces the insoluble etch product containing minute crystal particles on glass surface. By heating BGG glass at the optical fiber drawing temperature, the deposited surface layer turned to be amorphous again and results in the increase of the transmittance of glass. The results indicated that the HCl etching combined with subsequent high-temperature heat treatment is an effective approach to improve the surface quality of barium gallogermanate glass, which would reduce the optical loss of the final optical fiber.

  11. Mapping of fluoride endemic areas and assessment of fluoride exposure.

    PubMed

    Viswanathan, Gopalan; Jaswanth, A; Gopalakrishnan, S; Siva ilango, S

    2009-02-15

    The prevalence of fluorosis is mainly due to the consumption of more fluoride through drinking water. It is necessary to find out the fluoride endemic areas to adopt remedial measures to the people on the risk of fluorosis. The objectives of this study are to estimate the fluoride exposure through drinking water from people of different age group and to elucidate the fluoride endemic areas through mapping. Assessment of fluoride exposure was achieved through the estimation fluoride level in drinking water using fluoride ion selective electrode method. Google earth and isopleth technique were used for mapping of fluoride endemic areas. From the study it was observed that Nilakottai block of Dindigul district in Tamil Nadu is highly fluoride endemic. About 88% of the villages in this block have fluoride level more than the prescribed permissible limit in drinking water. Exposure of fluoride among different age groups was calculated in this block, which comprises 32 villages. The maximum estimated exposure doses were 0.19 mg/kg/day for infants, 0.17 mg/kg/day for children and 0.10 mg/kg/day for adults. When compared with adequate intake of minimal safe level exposure dose of 0.01 mg/kg/day for infants and 0.05 mg/kg/day for other age groups, a health risk due to fluorosis to the people in Nilakottai block has become evident. From the results, the people in Nilakottai block are advised to consume drinking water with fluoride level less than 1 mg/l. It has been recommended to the government authorities to take serious steps to supply drinking water with low fluoride concern for the fluorosis affected villages.

  12. Kinetics of photoplasma of dense barium vapour

    SciTech Connect

    Kosarev, N I

    2015-03-31

    Barium vapour ionisation under laser photoexcitation of the resonance line at a wavelength of λ = 553.5 nm is studied numerically. Seed electrons, arising due to the associative ionisation of atoms, gain energy in superelastic collisions and lead to electron avalanche ionisation of the medium. The influence of radiative transfer in a cylindrical gas volume on the excitation kinetics of barium atoms, absorption dynamics of laser radiation and oscillation of ionisation-brightening wave under competition between ionising and quenching collisions of electrons with excited atoms is studied. (interaction of laser radiation with matter)

  13. Health Effects Associated with Water Fluoridation.

    ERIC Educational Resources Information Center

    Richmond, Virginia L.

    1979-01-01

    Discussion is presented concerning fluoridation of water supplies. Correlation between fluoride in drinking water and improved dental health is reviewed. Relationship is expressed between fluoridation and reduced tooth decay. Use of fluoride in treating skeletal disorders is discussed. Author advocates fluoridating water supplies. (SA)

  14. Magnesium fluoride recovery method

    DOEpatents

    Gay, Richard L.; McKenzie, Donald E.

    1989-01-01

    A method of obtaining magnesium fluoride substantially free from radioactive uranium from a slag containing the same and having a radioactivity level of at least about 7000 pCi/gm. The slag is ground to a particle size of about 200 microns or less. The ground slag is contacted with an acid under certain prescribed conditions to produce a liquid product and a particulate solid product. The particulate solid product is separated from the liquid and treated at least two more times with acid to produce a solid residue consisting essentially of magnesium fluoride substantially free of uranium and having a residual radioactivity level of less than about 1000 pCi/gm. In accordance with a particularly preferred embodiment of the invention a catalyst and an oxidizing agent are used during the acid treatment and preferably the acid is sulfuric acid having a strength of about 1.0 Normal.

  15. 75 FR 19657 - Barium Chloride From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-15

    ... Chloride From China AGENCY: United States International Trade Commission. ACTION: Notice of Commission... China. SUMMARY: The Commission hereby gives notice that it will proceed with a full review pursuant to... antidumping duty order on barium chloride from China would be likely to lead to continuation or recurrence...

  16. Barium Transport Process in Impregnated Dispenser Cathodes.

    DTIC Science & Technology

    1982-01-25

    Distribution of Autoelectronic Emission from Single Crystal Metal Points. II. The Adsorption, Migration and Evaporation of Thorium, Barium, and Sodium on...1966, Alkaline Earth Tungstate : Equilibrium Instability in the M-W-O Systems, J. Am. Ceram. Soc. 49, p. 385. 26 LABORAT)RY OPIRATI JS The Labratory

  17. [Water fluoridation and public health].

    PubMed

    Barak, Shlomo

    2003-11-01

    Fluoridation in Israel was first mooted in 1973 and finally incorporated into law in November 2002 obligating the Ministry of Health to add fluoride to the nation's water supply. Epidemiology studies in the USA have shown that the addition of one part per million of fluoride to the drinking water reduced the caries rate of children's teeth by 50% to 60% with no side effects. Both the WHO in 1994 and the American Surgeon General's report of 2000 declared that fluoridation of drinking water was the safest and most efficient way of preventing dental caries in all age groups and populations. Opposition to fluoridation has arisen from "antifluoridation" groups who object to the "pollution" of drinking water by the addition of chemicals and mass medication in violation of the "Patient's Rights" law and the Basic Law of Human Dignity and Liberty. A higher prevalence of hip fractures in elderly osteoporotic women and osteosarcoma in teenagers has been reported in areas where excess fluoride exists in the drinking water. However, none of the many independent professional committees reviewing the negative aspects of fluoridation have found any scientific evidence associating fluoridation with any ill-effects or health problems. In Israel, where dental treatment is not included in the basket of Health Services, fluoridation is the most efficient and cheapest way of reducing dental disease, especially for the poorer members of the population.

  18. Water fluoridation and osteoporotic fracture.

    PubMed

    Hillier, S; Inskip, H; Coggon, D; Cooper, C

    1996-09-01

    Osteoporotic fractures constitute a major public health problem. These fractures typically occur at the hip, spine and distal forearm. Their pathogenesis is heterogeneous, with contributions from both bone strength and trauma. Water fluoridation has been widely proposed for its dental health benefits, but concerns have been raised about the balance of skeletal risks and benefits of this measure. Fluoride has potent effects on bone cell function, bone structure and bone strength. These effects are mediated by the incorporation of fluoride ions in bone crystals to form fluoroapatite, and through an increase in osteoblast activity. It is believed that a minimum serum fluoride level of 100 ng/ml must be achieved before osteoblasts will be stimulated. Serum levels associated with drinking water fluoridated to 1 ppm are usually several times lower than this value, but may reach this threshold at concentrations of 4 ppm in the drinking water. Animal studies suggest no effect of low-level (0-3 ppm) fluoride intake on bone strength, but a possible decrease at higher levels. Sodium fluoride has been used to treat established osteoporosis for nearly 30 years. Recent trials of this agent, prescribed at high doses, have suggested that despite a marked increase in bone mineral density, there is no concomitant reduction in vertebral fracture incidence. Furthermore, the increase in bone density at the lumbar spine may be achieved at the expense of bone mineral in the peripheral cortical skeleton. As a consequence, high dose sodium fluoride (80 mg daily) is not currently used to treat osteoporosis. At lower doses, recent trials have suggested a beneficial effect on both bone density and fracture. The majority of epidemiological evidence regarding the effect of fluoridated drinking water on hip fracture incidence is based on ecological comparisons. Although one Finnish study suggested that hip fracture rates in a town with fluoridated water were lower than those in a matching town

  19. Drinking water fluoridation and bone.

    PubMed

    Allolio, B; Lehmann, R

    1999-01-01

    Drinking water fluoridation has an established role in the prevention of dental caries, but may also positively or negatively affect bone. In bone fluoride is incorporated into hydroxylapatite to form the less soluble fluoroapatite. In higher concentrations fluoride stimulates osteoblast activity leading to an increase in cancellous bone mass. As optimal drinking water fluoridation (1 mg/l) is widely used, it is of great interest, whether long-term exposition to artificial water fluoridation has any impact on bone strength, bone mass, and -- most importantly -- fracture rate. Animal studies suggest a biphasic pattern of the effect of drinking water fluoridation on bone strength with a peak strength at a bone fluoride content of 1200 ppm followed by a decline at higher concentrations eventually leading to impaired bone quality. These changes are not paralleled by changes in bone mass suggesting that fluoride concentrations remain below the threshold level required for activation of osteoblast activity. Accordingly, in most epidemiological studies in humans bone mass was not altered by optimal drinking water fluoridation. In contrast, studies on the effect on hip fracture rate gave conflicting results ranging from an increased fracture incidence to no effect, and to a decreased fracture rate. As only ecological studies have been performed, they may be biased by unknown confounding factors -- the so-called ecological fallacy. However, the combined results of these studies indicate that any increase or decrease in fracture rate is likely to be small. It has been calculated that appropriately designed cohort studies to solve the problem require a sample size of >400,000 subjects. Such studies will not be performed in the foreseeable future. Future investigations in humans should, therefore, concentrate on the effect of long-term drinking water fluoridation on bone fluoride content and bone strength.

  20. Fluoride Content in Alcoholic Drinks.

    PubMed

    Goschorska, Marta; Gutowska, Izabela; Baranowska-Bosiacka, Irena; Rać, Monika Ewa; Chlubek, Dariusz

    2016-06-01

    The aim of the study was to determine the role of alcoholic drinks as a potential source of dietary fluoride by means of measuring fluoride levels in selected alcoholic drinks available on the Polish market that are also diverse in terms of the percentage content of ethanol. The study was conducted on 48 types of drinks with low, medium, and high alcohol content available on the Polish market and offered by various manufacturers, both Polish and foreign. Fluoride concentrations in individual samples were measured by potentiometric method with a fluoride ion-selective electrode. The highest fluoride levels were determined in the lowest percentage drinks (less than 10 % v/v ethanol), with the lowest fluoride levels observed in the highest percentage drinks (above 40 % v/v ethanol). In terms of types of alcoholic drinks, the highest fluoride levels were determined in beers and wines, while the lowest levels were observed in vodkas. These data confirm the fact that alcoholic beverages need to be considered as a significant source of fluoride delivered into the body.

  1. WET FLUORIDE SEPARATION METHOD

    DOEpatents

    Seaborg, G.T.; Gofman, J.W.; Stoughton, R.W.

    1958-11-25

    The separation of U/sup 233/ from thorium, protactinium, and fission products present in neutron-irradiated thorium is accomplished by dissolving the irradiated materials in aqueous nitric acid, adding either a soluble fluoride, iodate, phosphate, or oxalate to precipltate the thorium, separating the precipltate from the solution, and then precipitating uranlum and protactinium by alkalizing the solution. The uranium and protactinium precipitate is removcd from the solution and dissolved in nitric acid. The uranyl nitrate may then be extracted from the acid solution by means of ether, and the protactinium recovered from the aqueous phase.

  2. Caries management with fluoride agents.

    PubMed

    Lam, Anty; Chu, C H

    2012-11-01

    Dental caries is the single most common, chronic oral disease of childhood. It is progressive and cumulative, and becomes more complex over time. The Surgeon General's Report on Oral Health revealed that more than 51 million school hours are lost each year as a result of dental problems. Contemporary caries management philosophy has changed from the traditional surgical approach to a medical model that emphasizes prevention. Among various strategies for caries prevention or reduction, fluoride therapy has been highly promoted. Various in-office and over-the-counter fluoride products are available for caries prevention. Dental professionals should identify and assess the caries risk level of patients and optimize the use of fluorides in caries management. Since multiple sources of fluoride exposure exist, a coordinated approach to fluoride delivery is essential.

  3. A detailed analysis of five barium stars

    NASA Astrophysics Data System (ADS)

    Kovacs, N.

    1985-09-01

    A model-atmosphere analysis of five barium stars is carried out, and a previous analysis of two others extended. The sample comprises types Ba 1, Ba 2, Ba 3, and Ba 5. High-resolution Reticon spectra recorded with the ESO Coude Echelle Spectrometer serve to determine abundances relative to the sun for typically 16 elements. The use of Reticon spectra improves the accuracy compared to previous analyses. Enhancements of s-process elements relative to iron by factors of 2 (HD 139195) to 30 (HD 92626) are found; neutron exposures span at least the range tau of about 0.06-0.6/mb. In the more extreme barium stars the C/O ratio is enhanced with respect to normal red giants by a factor 2.5 to 30.

  4. The radiative lifetimes of O+2(a4[Pi]u, v) and NO+(a3[summation operator]+, v) revisited

    NASA Astrophysics Data System (ADS)

    Marx, R.; Fenistein, S.; Mauclaire, G.; Lemaire, J.; Heninger, M.

    1994-03-01

    The spin-forbidden radiative decays of metastable O+2(a4[Pi]u, v) and NO+(a3[summation operator]+, v) have been reinvestigated using our recently improved tirple cell FT-ICR spectrometer. The monitor ion technique was used to probe the first excited state of O+2(a4[Pi]u) and NO+(a3[summation operator]+). A radiative lifetime of (55 ± 7) ms has been found for O2+(a4[Pi]u) with Ar and CO2 as monitor gases. For NO+(a3[summation operator]+) we found (680+91-87) ms with CO2 (proving v [greater-or-equal, slanted] 0) and (516-62+65) ms with Ar (probing v [greater-or-equal, slanted] 1) respectively as monitor gases. For such long lifetimes it is mandatory to take into account collisional deactivation processes occurring in the relaxation cell even for pressures below 10-8 Torr. In order to correct the observed lifetimes, background gas pressure and rate constants have been carefully determined. For O+2, a double exponential decay due to the metastable state and to high vibrational levels of the ground state has been observed. As a consequence the experimental lifetimes depend on the observation time window explaining most of the differences with the previous published results. For NO+(a3[summation operator]+) the present lifetime is in good agreement with the results of Kuo. [C.H. Kuo, T. Wyttenbach, C.G. Beggs, P.R. Kemper and M.T. Bowers, J. Chem. Phys., 92 (1990) 4849] and with the recent theoretical calculations.

  5. Barium hexaferrite suspensions for electrophoretic deposition.

    PubMed

    Ovtar, Simona; Lisjak, Darja; Drofenik, Miha

    2009-09-15

    In this investigation we have looked at the preparation of barium hexaferrite suspensions, with the stability of the magnetic barium hexaferrite particles being increased by the addition of a surfactant, dodecylbenzylsulfonic acid (DBSA). The influence of the solubility DBSA in different solvents and its adsorption onto the surfaces of particles with different sizes were determined from zeta-potential measurements. The most suitable and stable suspensions of barium hexaferrite particles, regardless of their sizes, were obtained in 1-butanol, and these were then used for a subsequent electrophoretic deposition. The microstructures of the deposits were examined with electron microscopy. The thickness and density of the deposits as a function of the electric field, the zeta-potential, the particle size, and the separation distance between the electrodes were investigated. The thickness of the deposits was found to increase with the increasing zeta-potential of the suspension and with the increasing separation distance between the electrodes. Denser deposits were obtained from the suspensions of smaller particles that had narrower particle size distributions.

  6. Digital coincidence counting (DCC) and its use in the corrections for out-of-channel gamma events in 4pi beta-gamma coincidence counting.

    PubMed

    Keightle, J D; Watt, G C

    2002-01-01

    The digital coincidence counting system developed by NPL and ANSTO is briefly described along with its benefits in the data collection and processing for the 4pi beta-gamma coincidence counting technique of radionuclide standardization. One of these benefits is the automatic detection of and correction for out-of-channel coincidences in the Computer Discrimination method. Where the criteria for the use of the Cox-Isham/Smith correction formulae for dead times and resolving times are not met, a generalized approximation based on the work of Campion is suggested.

  7. The Detector for Advanced Neutron Capture Experiments: A 4{pi} BaF2 Detector for Neutron Capture Measurements at LANSCE

    SciTech Connect

    Ullmann, J.L.; Esch, E.-I.; Haight, R.C.; Hunt, L.; O'Donnell, J.M.; Reifarth, R.; Agvaanluvsan, U.; Alpizar, A.; Hatarik, R.; Bond, E.M.; Bredeweg, T.A.; Kronenberg, A.; Rundberg, R.S.; Vieira, D.J.; Wilhelmy, J.B.; Folden, C.M.; Hoffman, D.C.; Greife, U.; Schwantes, J.M.; Strottman, D.D.

    2005-05-24

    The Detector for Advanced Neutron Capture Experiments (DANCE) is a 162-element 4{pi} BaF2 array designed to make neutron capture cross-section measurements on rare or radioactive targets with masses as little as one milligram. Accurate capture cross sections are needed in many research areas, including stellar nucleosynthesis, advanced nuclear fuel cycles, waste transmutation, and other applied programs. These cross sections are difficult to calculate accurately and must be measured. The design and initial performance results of DANCE is discussed.

  8. Determination of Stability Constants of Hydrogen and Aluminum Fluorides with a Fluoride-Selective Electrode

    SciTech Connect

    Baumann, E.W.

    2003-01-06

    The ability to directly determine free fluoride ion concentration (or mean activity) simplifies gathering and interpretation of experimental data for studies of metal complexes. In this work, the new lanthanum fluoride electrode was used to measure free fluoride ion in an investigation of the hydrogen-fluoride and aluminum-fluoride systems in NH4NO3.

  9. Urinary Fluoride Concentration in Children with Disabilities Following Long-Term Fluoride Tablet Ingestion

    ERIC Educational Resources Information Center

    Liu, Hsiu-Yueh; Chen, Jung-Ren; Hung, Hsin-Chia; Hsiao, Szu-Yu; Huang, Shun-Te; Chen, Hong-Sen

    2011-01-01

    Urine is the most commonly utilized biomarker for fluoride excretion in public health and epidemiological studies. Approximately 30-50% of fluoride is excreted from urine in children. Urinary fluoride excretion reflects the total fluoride intake from multiple sources. After administering fluoride tablets to children with disabilities, urinary…

  10. Synthesis and Crystallization Behavior of Fluoride Glasses

    DTIC Science & Technology

    1989-08-22

    metal fluoride glasses. Exploration of synthesis conditions for converting precursors to multicomponent oxide gels for conversion to heavy metal fluoride...glasses. Exploration of chemistries and conditions for converting multicomponent oxide gels to heavy metal fluoride glasses. Exploration of...chemical approaches to passivating the surfaces of heavy metal fluoride glasses. Exploration of the possibility of developing a computer model to describe

  11. 49 CFR 173.163 - Hydrogen fluoride.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Hydrogen fluoride. 173.163 Section 173.163... Hydrogen fluoride. (a) Hydrogen fluoride (hydrofluoric acid, anhydrous) must be packaged as follows: (1) In... filling ratio of 0.84. (b) A cylinder removed from hydrogen fluoride service must be condemned...

  12. 49 CFR 173.163 - Hydrogen fluoride.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Hydrogen fluoride. 173.163 Section 173.163... Hydrogen fluoride. (a) Hydrogen fluoride (hydrofluoric acid, anhydrous) must be packaged as follows: (1) In... filling ratio of 0.84. (b) A cylinder removed from hydrogen fluoride service must be condemned...

  13. 49 CFR 173.163 - Hydrogen fluoride.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Hydrogen fluoride. 173.163 Section 173.163... Hydrogen fluoride. (a) Hydrogen fluoride (hydrofluoric acid, anhydrous) must be packaged as follows: (1) In... filling ratio of 0.84. (b) A cylinder removed from hydrogen fluoride service must be condemned...

  14. 49 CFR 173.163 - Hydrogen fluoride.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Hydrogen fluoride. 173.163 Section 173.163... Hydrogen fluoride. (a) Hydrogen fluoride (hydrofluoric acid, anhydrous) must be packaged as follows: (1) In... filling ratio of 0.84. (b) A cylinder removed from hydrogen fluoride service must be condemned...

  15. 49 CFR 173.163 - Hydrogen fluoride.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Hydrogen fluoride. 173.163 Section 173.163... Hydrogen fluoride. (a) Hydrogen fluoride (hydrofluoric acid, anhydrous) must be packaged as follows: (1) In... filling ratio of 0.84. (b) A cylinder removed from hydrogen fluoride service must be condemned...

  16. Creating unstable velocity-space distributions with barium injections

    NASA Technical Reports Server (NTRS)

    Pongratz, M. B.

    1983-01-01

    Ion velocity-space distributions resulting from barium injections from orbiting spacecraft and shaped charges are discussed. Active experiments confirm that anomalous ionization processes may operate, but photoionization accounts for the production of the bulk of the barium ions. Pitch-angle diffusion and/or velocity-space diffusion may occur, but observations of barium ions moving upwards against gravity suggests that the ions retain a significant enough fraction of their initial perpendicular velocity to provide a mirror force. The barium ion plasmas should have a range of Alfven Mach numbers and plasma betas. Because the initial conditions can be predicted these active experiments should permit testing plasma instability hypotheses.

  17. Lanthanide doped strontium-barium cesium halide scintillators

    DOEpatents

    Bizarri, Gregory; Bourret-Courchesne, Edith; Derenzo, Stephen E.; Borade, Ramesh B.; Gundiah, Gautam; Yan, Zewu; Hanrahan, Stephen M.; Chaudhry, Anurag; Canning, Andrew

    2015-06-09

    The present invention provides for a composition comprising an inorganic scintillator comprising an optionally lanthanide-doped strontium-barium, optionally cesium, halide, useful for detecting nuclear material.

  18. Fluoride-induced chronic renal failure.

    PubMed

    Lantz, O; Jouvin, M H; De Vernejoul, M C; Druet, P

    1987-08-01

    Renal fluoride toxicity in human beings is difficult to assess in the literature. Although experimental studies and research on methoxyflurane toxicity have shown frank renal damage, observations of renal insufficiency related to chronic fluoride exposure are scarce. We report a case of fluoride intoxication related to potomania of Vichy water, a highly mineralized water containing 8.5 mg/L of fluoride. Features of fluoride osteosclerosis were prominent and end-stage renal failure was present. The young age of the patient, the long duration of high fluoride intake, and the absence of other cause of renal insufficiency suggest a causal relationship between fluoride intoxication and renal failure.

  19. Spectral Diversity Crystalline Fluoride Lasers,

    DTIC Science & Technology

    1981-01-01

    2 4.-. i1.34 I R TUNABLE Table IX XeF Pumoe TM3 +: YLF :1 .Tm:YLF exhibits nearly ideal parameters for high energy operation aa3x10-20cm 2 ESAT 0cm e...host crystal, lithium yttrium fluoride, LiYF*4 ( YLF )" 1..0 Introductin Within the realm of crystalline laser materials,. the class of fluorides...on the host crystal, lithium yttrium fluoride, LiYF4 - often shortened as YLF . Tables I and 12 show the mechanical, thermal, and optical properties

  20. Strontium-90 fluoride data sheet

    SciTech Connect

    Fullam, H.T.

    1981-06-01

    This report is a compilation of available data and appropriate literature references on the properties of strontium-90 fluoride and nonradioactive strontium fluoride. The objective of the document is to compile in a single source pertinent data to assist potential users in the development, licensing, and use of /sup 90/SrF/sub 2/-fueled radioisotope heat sources for terrestrial power conversion and thermal applications. The report is an update of the Strontium-90 Fluoride Data Sheet (BNWL-2284) originally issued in April 1977.

  1. Molten fluoride fuel salt chemistry

    SciTech Connect

    Toth, L.M.; Del Cul, G.D.; Dai, S.; Metcalf, D.H.

    1994-09-01

    The chemistry of molten fluorides is traced from their development as fuels in the Molten Salt Reactor Experiment with important factors in their selection being discussed. Key chemical characteristics such as solubility, redox behavior, and chemical activity are explained as they relate to the behavior of molten fluoride fuel systems. Fission product behavior is described along with processing experience. Development requirements for fitting the current state of the chemistry to modern nuclear fuel system are described. It is concluded that while much is known about molten fluoride behavior, processing and recycle of the fuel components is a necessary factor if future systems are to be established.

  2. [Study on the vacuum ultraviolet transmittance of barium fluoride crystals at different temperature].

    PubMed

    Peng, Ru-Yi; Fu, Li-Ping; Tao, Ye

    2014-03-01

    Two VUV-grade BaF2 windows with 0.5 mm-thick and 1 mm-thick respectively were selected to study the transmittance variety with the temperature. The results show that the cutoff wavelength of BaF2 crystals will shift towards the long wave with the increase in temperature. In a certain temperature range, BaF2 crystals can depress 130.4 nm radiation well, and also has a high transmittance at 135.6 nm. Compared with the reported method in which SrF2 crystals can be applied to suppress 130.4 nm stray light by heating, BaF2 crystal can inhibit the 130. 4 nm emission line completely, and thus reduce the power consumption of the device at the same time. This indicates that BaF2 crystals can play an important role in the ionosphere optical remote sensing detection.

  3. Evaluation of wavelength shifters for spectral separation of barium fluoride emissions

    SciTech Connect

    DeVol, Timothy A.

    1993-01-01

    BaF2 has the advantage over other scintillators, when comparing radiation hardness, scintillation decay time, and fast scintillation yield. Since the fast BaF2 emissions have peak wavelengths of 220, 195, and 170 nm, a wavelength shifter (WLS) is needed. Organic fluors were evaluated as WLS components. Results indicate that spectral separation using WLS is possible, but not to the extent desired; other techniques must be used also. Alternative scintillators, such as CeF3, should be investigated.

  4. Fluorination utilizing thermodynamically unstable fluorides and fluoride salts thereof

    DOEpatents

    Bartlett, Neil; Whalen, J. Marc; Chacon, Lisa

    2000-12-12

    A method for fluorinating a carbon compound or cationic carbon compound utilizes a fluorination agent selected from thermodynamically unstable nickel fluorides and salts thereof in liquid anhydrous hydrogen fluoride. The desired carbon compound or cationic organic compound to undergo fluorination is selected and reacted with the fluorination agent by contacting the selected organic or cationic organic compound and the chosen fluorination agent in a reaction vessel for a desired reaction time period at room temperature or less.

  5. Binding and leakage of barium in alginate microbeads.

    PubMed

    Mørch, Yrr A; Qi, Meirigeng; Gundersen, Per Ole M; Formo, Kjetil; Lacik, Igor; Skjåk-Braek, Gudmund; Oberholzer, Jose; Strand, Berit L

    2012-11-01

    Microbeads of alginate crosslinked with Ca(2+) and/or Ba(2+) are popular matrices in cell-based therapy. The aim of this study was to quantify the binding of barium in alginate microbeads and its leakage under in vitro and accumulation under in vivo conditions. Low concentrations of barium (1 mM) in combination with calcium (50 mM) and high concentrations of barium (20 mM) in gelling solutions were used for preparation of microbeads made of high-G and high-M alginates. High-G microbeads accumulated barium from gelling solution and contained higher concentrations of divalent ions for both low- and high-Ba exposure compared with high-G microbeads exposed to calcium solely and to high-M microbeads for all gelling conditions. Although most of the unbound divalent ions were removed during the wash and culture steps, leakage of barium was still detected during storage. Barium accumulation in blood and femur bone of mice implanted with high-G beads was found to be dose-dependent. Estimated barium leakage relevant to transplantation to diabetic patients with islets in alginate microbeads showed that the leakage was 2.5 times lower than the tolerable intake value given by WHO for high-G microbeads made using low barium concentration. The similar estimate gave 1.5 times higher than is the tolerable intake value for the high-G microbeads made using high barium concentration. To reduce the risk of barium accumulation that may be of safety concern, the microbeads made of high-G alginate gelled with a combination of calcium and low concentration of barium ions is recommended for islet transplantation.

  6. A new perspective on metals and other contaminants in fluoridation chemicals*

    PubMed Central

    Mullenix, Phyllis J

    2014-01-01

    Background: Fluoride additives contain metal contaminants that must be diluted to meet drinking water regulations. However, each raw additive batch supplied to water facilities does not come labeled with concentrations per contaminant. This omission distorts exposure profiles and the risks associated with accidents and routine use. Objectives: This study provides an independent determination of the metal content of raw fluoride products. Methods: Metal concentrations were analyzed in three hydrofluorosilicic acid (HFS) and four sodium fluoride (NaF) samples using inductively coupled plasma-atomic emission spectrometry. Arsenic levels were confirmed using graphite furnace atomic absorption analysis. Results: Results show that metal content varies with batch, and all HFS samples contained arsenic (4.9–56.0 ppm) or arsenic in addition to lead (10.3 ppm). Two NaF samples contained barium (13.3–18.0 ppm) instead. All HFS (212–415 ppm) and NaF (3312–3630 ppm) additives contained a surprising amount of aluminum. Conclusions: Such contaminant content creates a regulatory blind spot that jeopardizes any safe use of fluoride additives. PMID:24999851

  7. Do Fluoride Ions Protect Teeth?

    ERIC Educational Resources Information Center

    Parkin, Christopher

    1998-01-01

    Begins with the procedure and results from an investigation on the effect of fluoride on the reaction between eggshell (substitute teeth) and dilute ethanoic acid. Describes an elegantly modified and improvised apparatus. (DDR)

  8. Fluoride glass: Crystallization, surface tension

    NASA Technical Reports Server (NTRS)

    Doremus, R. H.

    1988-01-01

    Fluoride glass was levitated acoustically in the ACES apparatus on STS-11, and the recovered sample had a different microstructure from samples cooled in a container. Further experiments on levitated samples of fluoride glass are proposed. These include nucleation, crystallization, melting observations, measurement of surface tension of molten glass, and observation of bubbles in the glass. Ground experiments are required on sample preparation, outgassing, and surface reactions. The results should help in the development and evaluation of containerless processing, especially of glass, in the development of a contaminent-free method of measuring surface tensions of melts, in extending knowledge of gas and bubble behavior in fluoride glasses, and in increasing insight into the processing and properties of fluoride glasses.

  9. 40 CFR 721.10011 - Barium calcium manganese strontium oxide.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Barium calcium manganese strontium... Specific Chemical Substances § 721.10011 Barium calcium manganese strontium oxide. (a) Chemical substance... manganese strontium oxide (PMN P-00-1124; CAS No. 359427-90-0) is subject to reporting under this...

  10. 40 CFR 721.10011 - Barium calcium manganese strontium oxide.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Barium calcium manganese strontium... Specific Chemical Substances § 721.10011 Barium calcium manganese strontium oxide. (a) Chemical substance... manganese strontium oxide (PMN P-00-1124; CAS No. 359427-90-0) is subject to reporting under this...

  11. 40 CFR 721.10011 - Barium calcium manganese strontium oxide.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Barium calcium manganese strontium... Specific Chemical Substances § 721.10011 Barium calcium manganese strontium oxide. (a) Chemical substance... manganese strontium oxide (PMN P-00-1124; CAS No. 359427-90-0) is subject to reporting under this...

  12. 40 CFR 721.10011 - Barium calcium manganese strontium oxide.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Barium calcium manganese strontium... Specific Chemical Substances § 721.10011 Barium calcium manganese strontium oxide. (a) Chemical substance... manganese strontium oxide (PMN P-00-1124; CAS No. 359427-90-0) is subject to reporting under this...

  13. 40 CFR 721.10011 - Barium calcium manganese strontium oxide.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Barium calcium manganese strontium... Specific Chemical Substances § 721.10011 Barium calcium manganese strontium oxide. (a) Chemical substance... manganese strontium oxide (PMN P-00-1124; CAS No. 359427-90-0) is subject to reporting under this...

  14. Europium-doped barium bromide iodide

    SciTech Connect

    Gundiah, Gautam; Hanrahan, Stephen M.; Hollander, Fredrick J.; Bourret-Courchesne, Edith D.

    2009-10-21

    Single crystals of Ba0.96Eu0.04BrI (barium europium bromide iodide) were grown by the Bridgman technique. The title compound adopts the ordered PbCl2 structure [Braekken (1932). Z. Kristallogr. 83, 222-282]. All atoms occupy the fourfold special positions (4c, site symmetry m) of the space group Pnma with a statistical distribution of Ba and Eu. They lie on the mirror planes, perpendicular to the b axis at y = +-0.25. Each cation is coordinated by nine anions in a tricapped trigonal prismatic arrangement.

  15. Short-cavity squeezing in barium

    NASA Technical Reports Server (NTRS)

    Hope, D. M.; Bachor, H-A.; Manson, P. J.; Mcclelland, D. E.

    1992-01-01

    Broadband phase sensitive noise and squeezing were experimentally observed in a system of barium atoms interacting with a single mode of a short optical cavity. Squeezing of 13 +/- 3 percent was observed. A maximum possible squeezing of 45 +/- 8 percent could be inferred for out experimental conditions, after correction for measured loss factors. Noise reductions below the quantum limit were found over a range of detection frequencies 60-170 MHz and were best for high cavity transmission and large optical depths. The amount of squeezing observed is consistent with theoretical predictions from a full quantum statistical model of the system.

  16. Vacancy ordering in reduced barium titanate

    NASA Astrophysics Data System (ADS)

    Woodward, David I.; Reaney, Ian M.; Yang, Gaiying Y.; Dickey, Elizabeth C.; Randall, Clive A.

    2004-06-01

    A crystal structure is proposed for reduced barium titanate, BaTiO3-δ, δ≈0.33, formed during the degradation of Ni-BaTiO3 X7R multilayer ceramic capacitors. High-resolution transmission electron microscopy and selected-area electron diffraction have been used in combination with computer simulations to show that oxygen vacancies accrete on every third pseudocubic {111} plane, resulting in a cell with space group P3m1. Additionally, from electron energy loss spectroscopy, it is proposed that Ti4+ is reduced to Ti3+ as a mechanism of charge compensation within oxygen-deficient octahedra.

  17. Barium appendicitis: A single institution review in Japan

    PubMed Central

    Katagiri, Hideki; Lefor, Alan Kawarai; Kubota, Tadao; Mizokami, Ken

    2016-01-01

    AIM To review clinical experience with barium appendicitis at a single institution. METHODS A retrospective review of patients admitted with a diagnosis of acute appendicitis, from January 1, 2013 to December 31, 2015 was performed. Age, gender, computed tomography (CT) scan findings if available, past history of barium studies, pathology, and the presence of perforation or the development of complications were reviewed. If the CT scan revealed high density material in the appendix, the maximum CT scan radiodensity of the material is measured in Hounsfield units (HU). Barium appendicitis is defined as: (1) patients diagnosed with acute appendicitis; (2) the patient has a history of a prior barium study; and (3) the CT scan shows high density material in the appendix. Patients who meet all three criteria are considered to have barium appendicitis. RESULTS In total, 396 patients were admitted with the diagnosis of acute appendicitis in the study period. Of these, 12 patients (3.0%) met the definition of barium appendicitis. Of these 12 patients, the median CT scan radiodensity of material in the appendix was 10000.8 HU, ranging from 3066 to 23423 HU (± 6288.2). In contrast, the median CT scan radiodensity of fecaliths in the appendix, excluding patients with barium appendicitis, was 393.1 HU, ranging from 98 to 2151 HU (± 382.0). The CT scan radiodensity of material in the appendices of patients with barium appendicitis was significantly higher than in patients with nonbarium fecaliths (P < 0.01). CONCLUSION Barium appendicitis is not rare in Japan. Measurement of the CT scan radiodensity of material in the appendix may differentiate barium appendicitis from routine appendicitis. PMID:27721929

  18. Barium sulfate aspiration: Severe chemical pneumonia induced by a massive reflux of contrast medium during small bowel barium enema.

    PubMed

    Zhang, Lin; Yang, Yi; Zhang, Ji; Zhou, Xiaowei; Dong, Hongmei; Zhou, Yiwu

    2015-08-01

    Barium contrast radiography is a conventional procedure aimed at revealing lesions of the alimentary tract using barium sulfate on X-ray irradiation. Although it is widely used in clinics, adverse effects and complications are observed, such as anaphylaxis, granuloma, fecalithes, abdomen-leaking, embolism, bacterial contamination, and aspiration. We report a case of death due to a massive barium sulfate aspiration resulted from an air-barium double contrast enema radiography. A 25-year-old female patient was hospitalized with symptoms of abdominal distention, nausea, vomiting and diarrhea for three days. A progressive respiratory distress presented only 1h after a small bowel air-barium double contrast enema. The patient died 11h later. The result of autopsy revealed the cause of death to be severe chemical pneumonitis induced by gastric fluid which was aspirated into her lungs. Barium sulfate is generally recognized to be chemically inert for the respiratory system, but a mixture of barium sulfate with gastric contents is fatal. Here we intend to suggest that, when determining the potential cause of death, medical examiners should consider a patient's status quo as well as the possible adverse effects and complications caused by the barium sulfate preparation during gastrointestinal radiography.

  19. Barium toxicity effects in soybean plants.

    PubMed

    Suwa, Ryuichi; Jayachandran, Krish; Nguyen, Nguyen Tran; Boulenouar, Abdellah; Fujita, Kounosuke; Saneoka, Hirofumi

    2008-10-01

    Barium (Ba)-induced phytotoxicity at 100, 1000, or 5000 microM Ba in soybean plants (Glycine max) was investigated under hydroponic culture conditions. Soybean growth and leaf photosynthetic activity were significantly inhibited by all three levels of Ba treatments. In the case of photosynthetic activity, 5000 microM Ba treatment shutdown stomatal opening and perturbed carbon fixation metabolism and translocation. However, 100 and 1000 microM Ba treatments shut down stomatal opening and inhibited carbon fixation, but without perturbation of leaf carbon fixation-related metabolism. Potassium (K) absorption by soybean roots was also reduced in all three Ba treatments. This decreased K absorption reduced K localization at guard cells. Barium accumulation in guard cells also inhibited K transport from epidermal cells to guard cells. This lack of K in guard cells resulted in stomatal closure. As a result of inhibition of K transport into guard cells and stomatal shutdown, photosynthetic activity and plant productivity were inhibited. Our experiment indicates that Ba has phytotoxic effects on soybean plants by inhibiting photosynthesis.

  20. Chronic fluoride toxicity: dental fluorosis.

    PubMed

    Denbesten, Pamela; Li, Wu

    2011-01-01

    Dental fluorosis occurs as a result of excess fluoride ingestion during tooth formation. Enamel fluorosis and primary dentin fluorosis can only occur when teeth are forming, and therefore fluoride exposure (as it relates to dental fluorosis) occurs during childhood. In the permanent dentition, this would begin with the lower incisors, which complete mineralization at approximately 2-3 years of age, and end after mineralization of the third molars. The white opaque appearance of fluorosed enamel is caused by a hypomineralized enamel subsurface. With more severe dental fluorosis, pitting and a loss of the enamel surface occurs, leading to secondary staining (appearing as a brown color). Many of the changes caused by fluoride are related to cell/matrix interactions as the teeth are forming. At the early maturation stage, the relative quantity of amelogenin protein is increased in fluorosed enamel in a dose-related manner. This appears to result from a delay in the removal of amelogenins as the enamel matures. In vitro, when fluoride is incorporated into the mineral, more protein binds to the forming mineral, and protein removal by proteinases is delayed. This suggests that altered protein/mineral interactions are in part responsible for retention of amelogenins and the resultant hypomineralization that occurs in fluorosed enamel. Fluoride also appears to enhance mineral precipitation in forming teeth, resulting in hypermineralized bands of enamel, which are then followed by hypomineralized bands. Enhanced mineral precipitation with local increases in matrix acidity may affect maturation stage ameloblast modulation, potentially explaining the dose-related decrease in cycles of ameloblast modulation from ruffle-ended to smooth-ended cells that occur with fluoride exposure in rodents. Specific cellular effects of fluoride have been implicated, but more research is needed to determine which of these changes are relevant to the formation of fluorosed teeth. As further

  1. Acute toxicity of ingested fluoride.

    PubMed

    Whitford, Gary Milton

    2011-01-01

    This chapter discusses the characteristics and treatment of acute fluoride toxicity as well as the most common sources of overexposure, the doses that cause acute toxicity, and factors that can influence the clinical outcome. Cases of serious systemic toxicity and fatalities due to acute exposures are now rare, but overexposures causing toxic signs and symptoms are not. The clinical course of systemic toxicity from ingested fluoride begins with gastric signs and symptoms, and can develop with alarming rapidity. Treatment involves minimizing absorption by administering a solution containing calcium, monitoring and managing plasma calcium and potassium concentrations, acid-base status, and supporting vital functions. Approximately 30,000 calls to US poison control centers concerning acute exposures in children are made each year, most of which involve temporary gastrointestinal effects, but others require medical treatment. The most common sources of acute overexposures today are dental products - particularly dentifrices because of their relatively high fluoride concentrations, pleasant flavors, and their presence in non-secure locations in most homes. For example, ingestion of only 1.8 ounces of a standard fluoridated dentifrice (900-1,100 mg/kg) by a 10-kg child delivers enough fluoride to reach the 'probably toxic dose' (5 mg/kg body weight). Factors that may influence the clinical course of an overexposure include the chemical compound (e.g. NaF, MFP, etc.), the age and acid-base status of the individual, and the elapsed time between exposure and the initiation of treatment. While fluoride has well-established beneficial dental effects and cases of serious toxicity are now rare, the potential for toxicity requires that fluoride-containing materials be handled and stored with the respect they deserve.

  2. Chronic Fluoride Toxicity: Dental Fluorosis

    PubMed Central

    DenBesten, Pamela; Li, Wu

    2012-01-01

    Dental fluorosis occurs as a result of excess fluoride ingestion during tooth formation. Enamel fluorosis and primary dentin fluorosis can only occur when teeth are forming, and therefore fluoride exposure (as it relates to dental fluorosis) occurs during childhood. In the permanent dentition, this would begin with the lower incisors, which complete mineralization at approximately 2–3 years of age, and end after mineralization of the third molars. The white opaque appearance of fluorosed enamel is caused by a hypomineralized enamel subsurface; with more severe dental fluorosis, pitting and a loss of the enamel surface occurs, leading to secondary staining (appearing as a brown color). Many of the changes caused by fluoride are related to cell/matrix/mineral interactions as the teeth are forming. At the early maturation stage, the relative quantity of amelogenin protein is increased in fluorosed enamel in a dose-related manner. This appears to result from a delay in the removal of amelogenins as the enamel matures. In vitro, when fluoride is incorporated into the mineral, more protein binds to the forming mineral, and protein removal by proteinases is delayed. This suggests that altered protein/mineral interactions are in part responsible for retention of amelogenins and the resultant hypomineralization that occurs in fluorosed enamel. Fluoride also appears to enhance mineral precipitation in forming teeth, resulting in hypermineralized bands of enamel, which are then followed by hypomineralized bands. Enhanced mineral precipitation with local increases in matrix acidity may affect maturation stage ameloblast modulation, potentially explaining the doserelated decrease in cycles of ameloblast modulation from ruffleended to smooth-ended cells that occur with fluoride exposure in rodents. Specific cellular effects of fluoride have been implicated, but more research is needed to determine which of these changes are relevant to the formation of fluorosed teeth. As

  3. Do all barium stars have a white dwarf companion?

    NASA Technical Reports Server (NTRS)

    Dominy, J. F.; Lambert, D. L.

    1983-01-01

    International Ultraviolet Explorer short-wavelength, low-dispersion spectra were analyzed for four barium, two mild barium, and one R-type carbon star in order to test the hypothesis that the barium and related giants are produced by mass transfer from a companion now present as a white dwarf. An earlier tentative identification of a white dwarf companion to the mild barium star Zeta Cyg is confirmed. For the other stars, no ultraviolet excess attributable to a white dwarf is seen. Limits are set on the bolometric magnitude and age of a possible white dwarf companion. Since the barium stars do not have obvious progenitors among main-sequence and subgiant stars, mass transfer must be presumed to occur when the mass-gaining star is already on the giant branch. This restriction, and the white dwarf's minimum age, which is greater than 8 x 10 to the 8th yr, determined for several stars, effectively eliminates the hypothesis that mass transfer from an asymptotic giant branch star creates a barium star. Speculations are presented on alternative methods of producing a barium star in a binary system.

  4. Microstructure and magnetism in barium strontium titanate (BSTO)-barium hexaferrite (BaM) multilayers

    SciTech Connect

    Frey, N.A.; Heindl, R.; Srinath, S.; Srikanth, H. . E-mail: sharihar@cas.usf.edu; Dudney, N.J.

    2005-08-11

    High quality multilayers of barium ferrite (BaM) and barium strontium titanate (BSTO) were grown in optimized conditions on thermally oxidized Si(1 0 0) and Al{sub 2}O{sub 3} substrates using magnetron sputtering. As-grown films were amorphous and different annealing procedures were explored to stabilize crystalline phases. BSTO and BaM phases were identified using X-ray diffraction and cross-sectional scanning electron micrographs showed sharp interfaces between BSTO and BaM layers. Magnetic hysteresis loops obtained at various temperatures and field orientations showed a large coercivity ({approx}2500 Oe) consistent with the hard magnetic hexaferrite component. Hysteresis loops also revealed the distinct influence of magnetocrystalline and shape anisotropies at different temperature ranges.

  5. [Natural fluorides. The distinction between technically produced and naturally occurring fluorides in caries prophylaxis].

    PubMed

    Newesely, H

    1977-06-01

    In the controversial discussion of the bio-availability of fluoride in caries prophylaxis by fluoridation, fluorides coming from the geochemical circulation to the biochemical circulation are sometimes differentiated from synthetic fluorides introduced into fluoride medication. The question as to whether such a differentiation is essential can be answered from the physical-chemical point of view. This requires a wide field of scientific research starting with geochemistry and the knowledge of fluoride deposits, sedimentology, hydrology, technology of inorganic and organic fluorine compounds, thermodynamics of dissolved fluorides, up to biocrystallography and biochemistry of fluorine.

  6. Proton conductivity of potassium doped barium zirconates

    SciTech Connect

    Xu Xiaoxiang; Tao Shanwen; Irvine, John T.S.

    2010-01-15

    Potassium doped barium zirconates have been synthesized by solid state reactions. It was found that the solubility limit of potassium on A-sites is between 5% and 10%. Introducing extra potassium leads to the formation of second phase or YSZ impurities. The water uptake of barium zirconates was increased even with 5% doping of potassium at the A-site. The sintering conditions and conductivity can be improved significantly by adding 1 wt% ZnO during material synthesis. The maximum solubility for yttrium at B-sites is around 15 at% after introducing 1 wt% zinc. The conductivity of Ba{sub 0.95}K{sub 0.05}Zr{sub 0.85}Y{sub 0.11}Zn{sub 0.04}O{sub 3-{delta}} at 600 deg. C is 2.2x10{sup -3} S/cm in wet 5% H{sub 2}. The activation energies for bulk and grain boundary are 0.29(2), 0.79(2) eV in wet 5% H{sub 2} and 0.31(1), 0.74(3) eV in dry 5% H{sub 2}. A power density of 7.7 mW/cm{sup 2} at 718 deg. C was observed when a 1 mm thick Ba{sub 0.95}K{sub 0.05}Zr{sub 0.85}Y{sub 0.11}Zn{sub 0.04}O{sub 3-{delta}} pellet was used as electrolyte and platinum electrodes. - Graphical abstract: Potassium doped barium zirconates have been synthesized by solid state reactions. It was found that the solubility limit of potassium on A-sites is between 5% and 10 %. The sintering conditions and conductivity can be improved significantly by adding 1 wt% ZnO during material synthesis. Five percent doping of potassium at A-site can double the total conductivity.

  7. High-fluoride groundwater.

    PubMed

    Rao, N Subba

    2011-05-01

    Fluoride (F(-)) is essential for normal bone growth, but its higher concentration in the drinking water poses great health problems and fluorosis is common in many parts of India. The present paper deals with the aim of establishment of facts of the chemical characteristics responsible for the higher concentration of F(-) in the groundwater, after understanding the chemical behavior of F(-) in relation to pH, total alkalinity (TA), total hardness (TH), carbonate hardness (CH), non-carbonate hardness (NCH), and excess alkalinity (EA) in the groundwater observed from the known areas of endemic fluorosis zones of Andhra Pradesh that have abundant sources of F(-)-bearing minerals of the Precambrians. The chemical data of the groundwater shows that the pH increases with increase F(-); the concentration of TH is more than the concentration of TA at low F(-) groundwater, the resulting water is represented by NCH; the TH has less concentration compared to TA at high F(-) groundwater, causing the water that is characterized by EA; and the water of both low and high concentrations of F(-) has CH. As a result, the F(-) has a positive relation with pH and TA, and a negative relation with TH. The operating mechanism derived from these observations is that the F(-) is released from the source into the groundwater by geochemical reactions and that the groundwater in its flowpath is subjected to evapotranspiration due to the influence of dry climate, which accelerates a precipitation of CaCO(3) and a reduction of TH, and thereby a dissolution of F(-). Furthermore, the EA in the water activates the alkalinity in the areas of alkaline soils, leading to enrichment of F(-). Therefore, the alkaline condition, with high pH and EA, and low TH, is a more conducive environment for the higher concentration of F(-) in the groundwater.

  8. Microcratering in Polyvinylidene Fluoride

    NASA Astrophysics Data System (ADS)

    Shu, Anthony John

    Dust is defined as macroparticles as small as a few molecules up to several micrometers in diameter. In the context of space exploration, it was originally seen only as a technical obstacle to applications; dust can damage instrument surfaces, coat mating surfaces preventing proper seals, and impair or obstruct measurements. Because of the ubiquity of dust in the solar system and its role in the origin of planets and other bodies, the study of dust and related phenomena has evolved to a scientific subdiscipline which can provide us insight into the origins and evolution of our solar system. In order to facilitate this, a hypervelocity dust accelerator has been built at the University of Colorado at Boulder and is being used to probe impact phenomena, dust mitigation techniques, dust detection techniques, and more. One such dust detector is a Polyvinylidene Fluoride (PVDF) dust detector. The PVDF dust detector is very lightweight and consumes little power. Due to these properties, PVDF detectors can potentially be used on any spacecraft to gain information on the local dust environment. It is not fully understood how this PVDF dust detector signal is generated, so at present can only be used as a dust counter. In this thesis I discuss the importance of the study of dust phenomena, describe the accelerator experiment, and describe a study conducted to determine the underlying physical principles of PVDF dust detectors. This included measuring crater size scaling laws, measuring the detailed shape of craters, and applying this data to simulations of the signals being generated by PVDF detectors.

  9. A high-altitude barium radial injection experiment

    NASA Technical Reports Server (NTRS)

    Wescott, E. M.; Stenbaek-Nielsen, H. C.; Hallinan, T. J.; Deehr, C. S.; Romick, G. J.; Olson, J. V.; Roederer, J. G.; Sydora, R.

    1980-01-01

    A rocket launched from Poker Flat, Alaska, carried a new type of high-explosive barium shaped charge to 571 km, where detonation injected a thin disk of barium vapor with high velocity nearly perpendicular to the magnetic field. The TV images of the injection are spectacular, revealing three major regimes of expanding plasma which showed early instabilities in the neutral gas. The most unusual effect of the injection is a peculiar rayed barium-ion structure lying in the injection plane and centered on a 5 km 'black hole' surrounding the injection point. Preliminary electrostatic computer simulations show a similar rayed development.

  10. Fluoride Glass Fibres For Telecommunications

    NASA Astrophysics Data System (ADS)

    Maze, Gwenael; Cardin, Vincent; Poulain, Marcel

    1983-09-01

    Zirconium fluoride glasses are the best known and the most stable beryllium-free glasses. They offer numerous potential uses for I.R.-transmitting fibres and ultra-long repeaterless optical wave-guides. Various problems arise in the manufacturing of fluoride glass fibres, essentially because of the steep viscosity profile and the devitrification phenomena. This paper discusses the processes for manufacturing step-index preforms and for drawing fibres. Optical quality preforms have been obtained and fibres have been drawn over more than 1 km. A spectral loss measurement system has been constructed using fluoride glass optical components. Several curves showing the optical attenuation versus wavelength are presented and discussed. These fibres are now available for optical transmission in infra-red systems.

  11. Anhydrous hydrogen fluoride electrolyte battery. [Patent application

    DOEpatents

    Not Available

    1972-06-26

    It is an object of the invention to provide a primary cell or battery using ammonium fluoride--anhydrous hydrogen fluoride electrolyte having improved current and power production capabilities at low temperatures. It is operable at temperatures substantially above the boiling point of hydrogen fluoride. (GRA)

  12. A Manual for Rural School Fluoridation.

    ERIC Educational Resources Information Center

    Sprouse, Larman W.; Brooks, John

    The product of a 1972 Dental Health Branch contract with the U.S. Public Health Service, this manual is designed to aid in the development of school fluoridation programs and presents: background information on general concepts relating to the action of fluoride on teeth; discussions dealing with community and school fluoridation studies; and the…

  13. The Effect of Fluoride in Osteoporosis.

    ERIC Educational Resources Information Center

    Hedlund, L. R.; Gallagher, J. C.

    1987-01-01

    This article discusses the effect of fluoride on bone tissue and the possible role of fluoride in the treatment of osteoporosis. At present, fluoride treatment should be restricted to clinical trials until its risks and benefits have been further evaluated. (Author/MT)

  14. Barium carbonate catalysis of carbon gasification

    SciTech Connect

    Ersolmaz, C.; Falconer, J.L.

    1985-01-01

    The interaction of barium carbonate with carbon black was studied to understand catalyzed CO/sub 2/ gasification of carbon. Temperature-programmed reaction with isotopic labeling of the carbonate and the carbon showed that carbon dramatically accelerated with rate of BaCO/sub 3/ decomposition to form BaO and CO/sub 2/, which rapidly gasified carbon to form CO. Pure BaCO/sub 3/ was observed to exchange carbon dioxide with the gas-phase, and the exchange rate was significantly increased by carbon at higher temperatures, due to formation of a carbon-carbonate complex. The interaction of BaCO/sub 3/ and C to form a complex occurred well below gasification temperatures, and BaCO/sub 3/ did not decompose until after gasification began and the gas phase CO/sub 2/ concentration was low.

  15. A triangular heterometallic siloxide containing barium

    SciTech Connect

    Coan, P.S.; Streib, W.E.; Caulton, K.G. )

    1991-12-25

    Reaction of KOSiPh[sub 3] with Ba[sub 3](OSiPh[sub 3])[sub 6](THF) in THF displaces barium from the triangular reagent to yield a colorless solid. Recrystallization in the presence of MeOC[sub 2]H[sub 4]OMe(DME) yields KBa[sub 2](OSiPh[sub 3])[sub 5](DME)[sub 2], characterized by [sup 1]H and [sup 29]Si NMR spectroscopy and X-ray diffraction. The molecule contains a triangular KBa[sub 2]([mu][sub 3]-OSiPh[sub 3])[sub 2]([mu][sub 2]-OSiPh[sub 3])[sub 3] core with [eta][sup 1] and [eta][sup 2]-DME ligation on each barium. The benzene-soluble molecule is fluxional in solution at both the OSiPh[sub 3] and the DME groups. At -70C in CH[sub 2]Cl[sub 2]/C[sub 6]D[sub 6], both [eta][sup 1]-DME/[eta][sup 2]-DME site exchange and intramolecular siloxide migration have been slowed, and the spectra are in agreement with retention of the solid-state structure in solution. Crystallographic data for KBa[sub 2](OSiPh[sub 3])[sub 5](DME)[sub 2] (-159C): a = 15.474 (3) [angstrom], b = 26.466 (6) [angstrom], c = 23.783 (5) [angstrom], [beta] = 99.80 (1)[degree] with Z = 4 in space group P2[sub 1]/n.

  16. METHOD OF PREPARING METAL FLUORIDES

    DOEpatents

    Katz, J.J.; Sheft, I.

    1959-08-11

    A method is presented for preparing the halides of elements which are relatively non-reactive with halogenating agents. The method involves reacting a mixture of an oxygen containing salt of a difficulty halogenated metal with an oxygen containing salt of an easily halogenated metal with a halogenating agent. Accordingly plutonium tetrafluoride is produced by reacting a mixture of plutonium dioxide and uranium octaoxide with bromine trifluoride. The reaction proceeds smoothly at moderate temperatures and the resulting plutonium trifluoride may be readily separated from many impurities which form volatile fluorides by volatilizing these volatile fluorides from the reaction chamber.

  17. Calculated emission rates for barium releases in space

    NASA Technical Reports Server (NTRS)

    Stenbaek-Nielsen, H. C.

    1989-01-01

    The optical emissions from barium releases in space are caused by resonance and fluorescent scattering of sunlight. Emission rates for the dominant ion and neutral lines are calculated assuming the release to be optically thin and the barium to be in radiative equilibrium with the solar radiation. The solar spectrum has deep Fraunhofer absorption lines at the primary barium ion resonances. A velocity component toward or away from the sun will Doppler shift the emission lines relative to the absorption lines and the emission rates will increase many-fold over the rest value. The Doppler brightening is important in shaped charge or satellite releases where the barium is injected at high velocities. Emission rates as a function of velocity are calculated for the 4554, 4934, 5854, 6142 and 6497 A ion emission lines and the dominant neutral line at 5535 A. Results are presented for injection parallel to the ambient magnetic field, B, and for injection at an angle to B.

  18. Upper gastrointestinal barium evaluation of duodenal pathology: A pictorial review

    PubMed Central

    Gupta, Pankaj; Debi, Uma; Sinha, Saroj Kant; Prasad, Kaushal Kishor

    2014-01-01

    Like other parts of the gastrointestinal tract (GIT), duodenum is subject to a variety of lesions both congenital and acquired. However, unlike other parts of the GIT viz. esophagus, rest of the small intestine and large intestine, barium evaluation of duodenal lesions is technically more challenging and hence not frequently reported. With significant advances in computed tomography technology, a thorough evaluation including intraluminal, mural and extramural is feasible in a single non-invasive examination. Notwithstanding, barium evaluation still remains the initial and sometimes the only imaging study in several parts of the world. Hence, a thorough acquaintance with the morphology of various duodenal lesions on upper gastrointestinal barium examination is essential in guiding further evaluation. We reviewed our experience with various common and uncommon barium findings in duodenal abnormalities. PMID:25170399

  19. Study of the photovoltaic effect in thin film barium titanate

    NASA Technical Reports Server (NTRS)

    Grannemann, W. W.; Dharmadhikari, V. S.

    1983-01-01

    The feasibility of making non-volatile digital memory devices of barium titanate, BaTiO3, that are integrated onto a silicon substrate with the required ferroelectric film produced by processing, compatible with silicon technology was examined.

  20. Synthesis, photoluminescence and magnetic properties of barium vanadate nanoflowers

    SciTech Connect

    Xu, Jing; Hu, Chenguo; Xi, Yi; Peng, Chen; Wan, Buyong; He, Xiaoshan

    2011-06-15

    Graphical abstract: The flower-shaped barium vanadate was obtained for the first time. The photoluminescence and magnetic properties of the barium vanadate nanoflowers were investigated at room temperature. Research highlights: {yields} In the paper, the flower-shaped barium vanadate were obtained for the first time. The CHM method used here is new and simple for preparation of barium vanadate. {yields} The photoluminescence and magnetic properties of the barium vanadate nanoflowers were investigated at room temperature. The strong bluish-green emission was observed. {yields} The ferromagnetic behavior of the barium vanadate nanoflowers was found with saturation magnetization of about 83.50 x 10{sup -3} emu/g, coercivity of 18.89 Oe and remnant magnetization of 4.63 x 10{sup -3} emu/g. {yields} The mechanisms of PL and magnetic property of barium vanadate nanoflowers have been discussed. -- Abstract: The flower-shaped barium vanadate has been obtained by the composite hydroxide mediated (CHM) method from V{sub 2}O{sub 5} and BaCl{sub 2} at 200 {sup o}C for 13 h. XRD and XPS spectrum of the as-synthesized sample indicate it is hexagonal Ba{sub 3}V{sub 2}O{sub 8} with small amount of Ba{sub 3}VO{sub 4.8} coexistence. Scan electron microscope and transmission electron microscope display that the flower-shaped crystals are composed of nanosheets with thickness of {approx}20 nm. The UV-visible spectrum shows that the barium vanadate sample has two optical gaps (3.85 eV and 3.12 eV). Photoluminescence spectrum of the barium vanadate flowers exhibits a visible light emission centered at 492 and 525 nm which might be attributed to VO{sub 4} tetrahedron with T{sub d} symmetry in Ba{sub 3}V{sub 2}O{sub 8}. The ferromagnetic behavior of the barium vanadate nanoflowers has been found with saturation magnetization of about 83.50 x 10{sup -3} emu/g, coercivity of 18.89 Oe and remnant magnetization of 4.63 x 10{sup -3} emu/g, which is mainly due to the presence of a non

  1. A search for technetium (Tc II) in barium stars

    NASA Technical Reports Server (NTRS)

    Little-Marenin, Irene R.; Little, Stephen J.

    1987-01-01

    The authors searched without success for the lines of Tc II at 2647.02, 2610.00 and 2543.24 A in IUE spectra of the barium stars HR 5058, Omicron Vir, and Zeta Cap. The lack of Tc II implies that the observed s-process enhancements were produced more than half a million years ago and supports the suggestion that the spectral peculiarities of barium stars are probably related to the binary nature of the stars.

  2. 'Skidding' of the CRRES G-9 barium release

    NASA Technical Reports Server (NTRS)

    Huba, J. D.; Mitchell, H. G.; Fedder, J. A.; Bernhardt, P. A.

    1992-01-01

    A simulation study and experimental data of the CRRES G-9 ionospheric barium release are presented. The simulation study is based on a 2D electrostatic code that incorporates time-dependent coupling to the background plasma. It is shown that the densest portion of the barium ion cloud 'skids' about 15 km within the first three seconds following the release, consistent with the optical data analyses.

  3. Total fluoride intake and excretion in children up to 4 years of age living in fluoridated and non-fluoridated areas.

    PubMed

    Zohoori, F V; Buzalaf, M A R; Cardoso, C A B; Olympio, K P K; Levy, F M; Grizzo, L T; Mangueira, D F B; Sampaio, F C; Maguire, A

    2013-10-01

    Fractional fluoride retention is important during the early years of life when considering the risk of development of dental fluorosis. This study aimed to measure fractional fluoride retention in young children. The objectives were to investigate the relationships between fractional fluoride retention and total daily fluoride intake, age, and body mass index (BMI). Twenty-nine healthy children, up to 4 yr of age, participated; 14 lived in a fluoridated area (0.64 μg ml(-1) of fluoride in drinking water) and 15 lived in a non-fluoridated area (0.04 μg ml(-1) of fluoride in drinking water). The total daily fluoride intake of each child was calculated from the daily dietary fluoride intake and toothpaste ingestion (if fluoride toothpaste was used). Total daily fluoride excretion was measured by collecting voided urine and faeces over a 24-h period, and fractional fluoride retention was calculated by dividing the amount of fluoride retained in the body (total daily fluoride intake minus total daily fluoride excretion) by the total daily fluoride intake. Nine children were excluded from data analysis because of suspected invalid samples. Mean (range) fractional fluoride retention for the remaining 20 children was 0.61 (0.06-0.98). There were no statistically significant correlations between fractional fluoride retention and either age or BMI. However, fractional fluoride retention was correlated with total daily fluoride intake: fractional fluoride retention = 1 - exp (-C × total daily fluoride intake), where C = 28.75 (95% CI = 19.75-37.75). The wide variation in fluoride retention in young children could have important implications when recommendations for fluoride use are being considered.

  4. The role of fluoride in erosion therapy.

    PubMed

    Huysmans, Marie-Charlotte; Young, Alix; Ganss, Carolina

    2014-01-01

    The role of fluoride in erosion therapy has long been questioned. However, recent research has yielded positive results. In this chapter, an overview of the literature is provided regarding the application of fluorides in the prevention and treatment of erosion and erosive wear. The results are presented and discussed for different fluoride sources such as monovalent and polyvalent fluorides, and for different vehicles such as toothpastes, solutions and rinses, as well as varnishes and gels. It is concluded that fluoride applications are very likely to be of use in the preventive treatment of erosive wear. Most promising are high-concentration, acidic formulations and the polyvalent fluoride sources, with the best evidence available for stannous fluoride. However, the evidence base for clinical effectiveness is still small.

  5. Special Report: Fluoridation of Water.

    ERIC Educational Resources Information Center

    Hileman, Bette

    1988-01-01

    Reviews the controversy regarding water fluoridation in the United States during the last 50 years. Discusses the current status; benefits; and health risks including skeletal fluorosis, kidney disease, hypersensitivity, mutagenic effects, birth defects, and cancer. Presents statistics and anecdotal accounts. (CW)

  6. Electron Collisions with Hydrogen Fluoride

    NASA Astrophysics Data System (ADS)

    Itikawa, Yukikazu

    2017-03-01

    Cross section data are reviewed for electron collisions with hydrogen fluoride. Collision processes considered are total scattering, elastic scattering, excitations of rotational, vibrational, and electronic states, ionization, and dissociative electron attachment. After a survey of the literature, recommended values of the cross sections are determined, as far as possible.

  7. Fissure seal or fluoride varnish?

    PubMed

    Deery, Christopher

    2016-09-01

    Data sourcesCochrane Oral Health Group Trials Register, the Cochrane Central Register of Controlled Trials (CENTRAL), Medline, Embase, the US National Institutes of Health Trials Register and the World Health Organization (WHO) Clinical Trials Registry PlatformStudy selectionRandomised controlled trials (RCTs) with at least 12 months follow-up, in which fissure sealants, or fissure sealants together with fluoride varnishes, were compared with fluoride varnishes alone for preventing caries in occlusal surfaces of permanent teeth of children and adolescents.Data extraction and synthesisTwo reviewers independently screened search results, extracted data and assessed risk of bias of included studies. Studies were grouped and analysed on the basis of sealant material type (resin-based sealant and glass ionomer-based sealant, glass ionomer and resin-modified glass ionomer) and different follow-up periods. Odds ratio were calculated for caries or no caries on occlusal surfaces of permanent molar teeth. Mean differences were calculated for continuous outcomes and data. Evidence quality was assessed using GRADE (Grades of Recommendation, Assessment, Development and Evaluation) methods.ResultsEight RCTs involving a total of 1747 children aged five to ten years of age were included. Three trials compared resin-based fissure sealant versus fluoride varnish. Results from two studies (358 children) after two years were combined. Sealants prevented more caries, pooled odds ratio (OR) = 0.69 (95%CI; 0.50 to 0.94). One trial with follow-up at four and nine years found that the caries-preventive benefit for sealants was maintained, with 26% of sealed teeth and 55.8% of varnished teeth having developed caries at nine years. Evidence for glass-ionomer sealants was of low quality. One split-mouth trial analysing 92 children at two-year follow-up found a significant difference in favour of resin-based fissure sealant together with fluoride varnish compared with fluoride varnish only (OR

  8. Fluoride in groundwater: toxicological exposure and remedies.

    PubMed

    Jha, S K; Singh, R K; Damodaran, T; Mishra, V K; Sharma, D K; Rai, Deepak

    2013-01-01

    Fluoride is a chemical element that is found most frequently in groundwater and has become one of the most important toxicological environmental hazards globally. The occurrence of fluoride in groundwater is due to weathering and leaching of fluoride-bearing minerals from rocks and sediments. Fluoride when ingested in small quantities (<0.5 mg/L) is beneficial in promoting dental health by reducing dental caries, whereas higher concentrations (>1.5 mg/L) may cause fluorosis. It is estimated that about 200 million people, from among 25 nations the world over, may suffer from fluorosis and the causes have been ascribed to fluoride contamination in groundwater including India. High fluoride occurrence in groundwaters is expected from sodium bicarbonate-type water, which is calcium deficient. The alkalinity of water also helps in mobilizing fluoride from fluorite (CaF2). Fluoride exposure in humans is related to (1) fluoride concentration in drinking water, (2) duration of consumption, and (3) climate of the area. In hotter climates where water consumption is greater, exposure doses of fluoride need to be modified based on mean fluoride intake. Various cost-effective and simple procedures for water defluoridation techniques are already known, but the benefits of such techniques have not reached the rural affected population due to limitations. Therefore, there is a need to develop workable strategies to provide fluoride-safe drinking water to rural communities. The study investigated the geochemistry and occurrence of fluoride and its contamination in groundwater, human exposure, various adverse health effects, and possible remedial measures from fluoride toxicity effects.

  9. Results on search for a QGP with a TPC magnetic spectrometer at AGS and plans for an approx 4. pi. TPC magnetic spectrometer at RHIC

    SciTech Connect

    Lindenbaum, S.J. City Univ. of New York, NY )

    1991-01-01

    In the first part of this paper a search for a Quark-Gluon Plasma (QGP) with a TPC Magnetic Spectrometer at AGS by the BNL/CCNY/Johns Hopkins/Rice (E-810) Collaboration is discussed. At AGS energies the expected increase in baryon density is near maximum. If a QGP is formed even rarely this approach provides a sensitive method for its detection. We have found some interesting phenomena including strangeness enhancement, multi-{Lambda} and K{sub s}{sup 0} events and an increased slope for {pi}{sup {minus}} (corresponding to a reduced temperature) in the usual temperature plot for p{sub {perpendicular}} < 0.2 GeV/c. We plan to increase the statistics with the 14.5 GeV/c {times} A Si ions on targets from light to heavy and then to continue the program with incident Au ions. In Part 2 we discuss the BNL/CCNY/Notre Dame/Rice proposal for an {approx} 4{pi} TPC Magnetic Spectrometer for RHIC which we believe will be a sensitive probe for hadronic QGP signals, and also capable of observing departures from QCD should they occur. 8 refs., 12 figs.

  10. Determining the optimal fluoride concentration in drinking water for fluoride endemic regions in South India.

    PubMed

    Viswanathan, Gopalan; Jaswanth, A; Gopalakrishnan, S; Siva Ilango, S; Aditya, G

    2009-10-01

    Fluoride ion in drinking water is known for both beneficial and detrimental effects on health. The prevalence of fluorosis is mainly due to the intake of large quantities of fluoride through drinking water owing to more than 90% bioavailability. The objective of this study is to predict optimal fluoride level in drinking water for fluoride endemic regions by comprising the levels of fluoride and other water quality parameters in drinking water, prevalence of fluorosis, fluoride intake through water, food and beverages such as tea and coffee and also considering the progressive accumulation of fluoride in animal bones, by comparing with non fluoride endemic areas comprise of the same geological features with the aid of regression analysis. Result of this study shows that increase of fluoride level above 1.33 mg/l in drinking water increases the community fluorosis index (CFI) value more than 0.6, an optimum index value above which fluorosis is considered to be a public health problem. Regression plot between water fluoride and bone fluoride levels indicates that, every increase of 0.5mg/l unit of water fluoride level increases the bone fluoride level of 52 mg/kg unit within 2 to 3 years. Furthermore, the consumption of drinking water containing more than 0.65 mg/l of fluoride can raise the total fluoride intake per day more than 4 mg, which is the optimum fluoride dose level recommended for adults by the Agency for Toxic Substances and Disease Registry. From the result, the people in fluoride endemic areas in South India are advised to consume drinking water with fluoride level within the limit of 0.5 to 0.65 mg/l to avoid further fluorosis risk.

  11. Global affordability of fluoride toothpaste

    PubMed Central

    Goldman, Ann S; Yee, Robert; Holmgren, Christopher J; Benzian, Habib

    2008-01-01

    Objective Dental caries remains the most common disease worldwide and the use of fluoride toothpaste is a most effective preventive public health measure to prevent it. Changes in diets following globalization contribute to the development of dental caries in emerging economies. The aim of this paper is to compare the cost and relative affordability of fluoride toothpaste in high-, middle- and low-income countries. The hypothesis is that fluoride toothpaste is not equally affordable in high-, middle- and low-income countries. Methods Data on consumer prices of fluoride toothpastes were obtained from a self-completion questionnaire from 48 countries. The cost of fluoride toothpaste in high-, middle- and low-income countries was compared and related to annual household expenditure as well as to days of work needed to purchase the average annual usage of toothpaste per head. Results The general trend seems to be that the proportion of household expenditure required to purchase the annual dosage of toothpaste increases as the country's per capita household expenditure decreases. While in the UK for the poorest 30% of the population only 0.037 days of household expenditure is needed to purchase the annual average dosage (182.5 g) of the lowest cost toothpaste, 10.75 days are needed in Kenya. The proportion of annual household expenditure ranged from 0.02% in the UK to 4% in Zambia to buy the annual average amount of lowest cost toothpaste per head. Conclusion Significant inequalities in the affordability of this essential preventive care product indicate the necessity for action to make it more affordable. Various measures to improve affordability based on experiences from essential pharmaceuticals are proposed. PMID:18554382

  12. Dynamics of Fluoride Bioavailability in the Biofilms of Different Oral Surfaces after Amine Fluoride and Sodium Fluoride Application

    PubMed Central

    Naumova, Ella A.; Dickten, Christoph; Jung, Rico; Krauss, Florian; Rübesamen, Henrik; Schmütsch, Katharina; Sandulescu, Tudor; Zimmer, Stefan; Arnold, Wolfgang H.

    2016-01-01

    It was the aim of this study to investigate differences in fluoride bioavailability in different oral areas after the application of amine fluoride (AmF) and sodium fluoride (NaF). The null hypothesis suggested no differences in the fluoride bioavailability. The tongue coating was removed and biofilm samples from the palate, oral floor and cheeks were collected. All subjects brushed their teeth with toothpaste containing AmF or NaF. Specimens were collected before, as well as immediately after and at 30 and 120 minutes after tooth brushing. The fluoride concentration was determined. The area under the curve was calculated for each location and compared statistically. In the tongue coating, fluoride concentration increased faster after NaF application than after AmF application. After 30 minutes, the fluoride concentration decreased and remained stable until 120 minutes after AmF application and returned to baseline after NaF application. The difference between the baseline and the endpoint measurements was statistically significant. The fluoride concentration in the tongue coating remained at a higher level compared with the baseline for up to 120 minutes post-brushing. This may indicate that the tongue coating is a major reservoir for fluoride bioavailability. The results also indicate an unequal fluoride distribution in the oral cavity. PMID:26727989

  13. Anastomotic stenosis of the descending colon caused by barium granuloma formation following barium peritonitis: report of a case.

    PubMed

    Kitajima, Toshihiro; Tomizawa, Kenji; Hanaoka, Yutaka; Toda, Shigeo; Matoba, Shuichiro; Kuroyanagi, Hiroya; Oota, Yasunori

    2014-11-01

    Anastomotic stricture reportedly often recurs following barium peritonitis, regardless of whether the anastomotic diameter is initially sufficient. However, the causes of repetitive stricture have not been clarified. We report a case that suggests the pathophysiology of recurrent anastomotic strictures following barium peritonitis. The patient was a 39-year-old Japanese man with idiopathic perforation of the descending colon after undergoing an upper gastrointestinal barium contrast study. After emergency peritoneal lavage and diverting colostomy, created using the perforated region, the patient recovered uneventfully and 3 months later, the colostomy was closed and the perforated colon was resected. However, 7 months after colostomy closure, abdominal distention gradually developed, and colonoscopy revealed an anastomotic stricture. The patient was referred to our hospital where he underwent resection of the anastomotic stricture. The surgical specimen exhibited barium granulomas not only in the subserosa of the entire specimen, but also in the submucosa and lamina propria localized in the anastomotic site. These findings suggest that barium was embedded in the submucosa and lamina propria with manipulation of the stapled anastomosis and that the barium trapped in the anastomotic site caused persistent inflammation, resulting in an anastomotic stricture.

  14. Barium determination in gastric contents, blood and urine by inductively coupled plasma mass spectrometry in the case of oral barium chloride poisoning.

    PubMed

    Łukasik-Głębocka, Magdalena; Sommerfeld, Karina; Hanć, Anetta; Grzegorowski, Adam; Barałkiewicz, Danuta; Gaca, Michał; Zielińska-Psuja, Barbara

    2014-01-01

    A serious case of barium intoxication from suicidal ingestion is reported. Oral barium chloride poisoning with hypokalemia, neuromuscular and cardiac toxicity, treated with intravenous potassium supplementation and hemodialysis, was confirmed by the determination of barium concentrations in gastric contents, blood, serum and urine using the inductively coupled plasma mass spectrometry method. Barium concentrations in the analyzed specimens were 20.45 µg/L in serum, 150 µg/L in blood, 10,500 µg/L in urine and 63,500 µg/L in gastric contents. Results were compared with barium levels obtained from a non-intoxicated person.

  15. 21 CFR 177.2510 - Polyvinylidene fluoride resins.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Polyvinylidene fluoride resins. 177.2510 Section... Repeated Use § 177.2510 Polyvinylidene fluoride resins. Polyvinylidene fluoride resins may be safely used... fluoride resins consist of basic resins produced by the polymerization of vinylidene fluoride. (b)...

  16. Focus on Fluorides: Update on the Use of Fluoride for the Prevention of Dental Caries

    PubMed Central

    Carey, Clifton M.

    2014-01-01

    Declarative Title: Improving the efficacy of fluoride therapies reduces dental caries and lowers fluoride exposure. Background Fluoride is delivered to the teeth systemically or topically to aid in the prevention of dental caries. Systemic fluoride from ingested sources is in blood serum and can be deposited only in teeth that are forming in children. Topical fluoride is from sources such as community water, processed foods, beverages, toothpastes, mouthrinses, gels, foams, and varnishes. The United States Centers for Disease Control and Prevention (CDC) and the American Dental Association (ADA) have proposed changes in their long standing recommendations for the amount of fluoride in community drinking water in response to concerns about an increasing incidence of dental fluorosis in children. Current research is focused on the development of strategies to improve fluoride efficacy. The purpose of this update is to inform the reader about new research and policies related to the use of fluoride for the prevention of dental caries. Methods Reviews of the current research and recent evidence based systematic reviews on the topics of fluoride are presented. Topics discussed include: updates on community water fluoridation research and policies; available fluoride in dentifrices; fluoride varnish compositions, use, and recommendations; and other fluoride containing dental products. This update provides insights into current research and discusses proposed policy changes for the use of fluoride for the prevention of dental caries. Conclusions The dental profession is adjusting their recommendations for fluoride use based on current observations of the halo effect and subsequent outcomes. The research community is focused on improving the efficacy of fluoride therapies thus reducing dental caries and lowering the amount of fluoride required for efficacy. PMID:24929594

  17. Eukaryotic resistance to fluoride toxicity mediated by a widespread family of fluoride export proteins.

    PubMed

    Li, Sanshu; Smith, Kathryn D; Davis, Jared H; Gordon, Patricia B; Breaker, Ronald R; Strobel, Scott A

    2013-11-19

    Fluorine is an abundant element and is toxic to organisms from bacteria to humans, but the mechanisms by which eukaryotes resist fluoride toxicity are unknown. The Escherichia coli gene crcB was recently shown to be regulated by a fluoride-responsive riboswitch, implicating it in fluoride response. There are >8,000 crcB homologs across all domains of life, indicating that it has an important role in biology. Here we demonstrate that eukaryotic homologs [renamed FEX (fluoride exporter)] function in fluoride export. FEX KOs in three eukaryotic model organisms, Neurospora crassa, Saccharomyces cerevisiae, and Candida albicans, are highly sensitized to fluoride (>200-fold) but not to other halides. Some of these KO strains are unable to grow in fluoride concentrations found in tap water. Using the radioactive isotope of fluoride, (18)F, we developed an assay to measure the intracellular fluoride concentration and show that the FEX deletion strains accumulate fluoride in excess of the external concentration, providing direct evidence of FEX function in fluoride efflux. In addition, they are more sensitive to lower pH in the presence of fluoride. These results demonstrate that eukaryotic FEX genes encode a previously unrecognized class of fluoride exporter necessary for survival in standard environmental conditions.

  18. High H- ionic conductivity in barium hydride

    NASA Astrophysics Data System (ADS)

    Verbraeken, Maarten C.; Cheung, Chaksum; Suard, Emmanuelle; Irvine, John T. S.

    2015-01-01

    With hydrogen being seen as a key renewable energy vector, the search for materials exhibiting fast hydrogen transport becomes ever more important. Not only do hydrogen storage materials require high mobility of hydrogen in the solid state, but the efficiency of electrochemical devices is also largely determined by fast ionic transport. Although the heavy alkaline-earth hydrides are of limited interest for their hydrogen storage potential, owing to low gravimetric densities, their ionic nature may prove useful in new electrochemical applications, especially as an ionically conducting electrolyte material. Here we show that barium hydride shows fast pure ionic transport of hydride ions (H-) in the high-temperature, high-symmetry phase. Although some conductivity studies have been reported on related materials previously, the nature of the charge carriers has not been determined. BaH2 gives rise to hydride ion conductivity of 0.2 S cm-1 at 630 °C. This is an order of magnitude larger than that of state-of-the-art proton-conducting perovskites or oxide ion conductors at this temperature. These results suggest that the alkaline-earth hydrides form an important new family of materials, with potential use in a number of applications, such as separation membranes, electrochemical reactors and so on.

  19. High pressure FAST of nanocrystalline barium titanate

    DOE PAGES

    Fraga, Martin B.; Delplanque, Jean -Pierre; Yang, Nancy; ...

    2016-06-01

    Here, this work studies the microstructural evolution of nanocrystalline (<1 µm) barium titanate (BaTiO3), and presents high pressure in field-assisted sintering (FAST) as a robust methodology to obtain >100 nm BaTiO3 compacts. Using FAST, two commercial ~50 nm powders were consolidated into compacts of varying densities and grain sizes. Microstructural inhomogeneities were investigated for each case, and an interpretation is developed using a modified Monte Carlo Potts (MCP) simulation. Two recurrent microstructural inhomogeneities are highlighted, heterogeneous grain growth and low-density regions, both ubiqutously present in all samples to varying degrees. In the worst cases, HGG presents an area coverage ofmore » 52%. Because HGG is sporadic but homogenous throughout a sample, the catalyst (e.g., the local segregation of species) must be, correspondingly, distributed in a homogenous manner. MCP demonstrates that in such a case, a large distance between nucleating abnormal grains is required—otherwise abnormal grains prematurely impinge on each other, and their size is not distinguishable from that of normal grains. Compacts sintered with a pressure of 300 MPa and temperatures of 900 °C, were 99.5% dense and had a grain size of 90±24 nm. These are unprecedented results for commercial BaTiO3 powders or any starting powder of 50 nm particle size—other authors have used 16 nm lab-produced powder to obtain similar results.« less

  20. High pressure FAST of nanocrystalline barium titanate

    SciTech Connect

    Fraga, Martin B.; Delplanque, Jean -Pierre; Yang, Nancy; Lavernia, Enrique J.; Monson, Todd C.

    2016-06-01

    Here, this work studies the microstructural evolution of nanocrystalline (<1 µm) barium titanate (BaTiO3), and presents high pressure in field-assisted sintering (FAST) as a robust methodology to obtain >100 nm BaTiO3 compacts. Using FAST, two commercial ~50 nm powders were consolidated into compacts of varying densities and grain sizes. Microstructural inhomogeneities were investigated for each case, and an interpretation is developed using a modified Monte Carlo Potts (MCP) simulation. Two recurrent microstructural inhomogeneities are highlighted, heterogeneous grain growth and low-density regions, both ubiqutously present in all samples to varying degrees. In the worst cases, HGG presents an area coverage of 52%. Because HGG is sporadic but homogenous throughout a sample, the catalyst (e.g., the local segregation of species) must be, correspondingly, distributed in a homogenous manner. MCP demonstrates that in such a case, a large distance between nucleating abnormal grains is required—otherwise abnormal grains prematurely impinge on each other, and their size is not distinguishable from that of normal grains. Compacts sintered with a pressure of 300 MPa and temperatures of 900 °C, were 99.5% dense and had a grain size of 90±24 nm. These are unprecedented results for commercial BaTiO3 powders or any starting powder of 50 nm particle size—other authors have used 16 nm lab-produced powder to obtain similar results.

  1. Salivary fluoride levels after use of high-fluoride dentifrice.

    PubMed

    Vale, Glauber Campos; Cruz, Priscila Figueiredo; Bohn, Ana Clarissa Cavalcante Elvas; de Moura, Marcoeli Silva

    2015-01-01

    The aim of the study was to evaluate salivary fluoride (F) availability after toothbrushing with a high-F dentifrice. Twelve adult volunteers took part in this crossover and blind study. F concentration in saliva was determined after brushing with a high-F dentifrice (5000 µg F/g) or with a conventional F concentration dentifrice (1100 µg F/g) followed by a 15 mL distilled water rinse. Samples of nonstimulated saliva were collected on the following times: before (baseline), and immediately after spit (time = 0) and after 1, 2, 3, 4, 5, 10, 15, 20, 30, 45, 60, 90, and 120 min. F analysis was performed with a fluoride-sensitive electrode and the area under curve of F salivary concentration × time (µg F/mL × min(-1)) was calculated. At baseline, no significant difference was found among dentifrices (P > 0.05). After brushing, both dentifrices caused an elevated fluoride level in saliva; however salivary F concentration was significantly higher at all times, when high-F dentifrice was used (P < 0.01). Even after 120 min, salivary F concentration was still higher than the baseline values for both dentifrices (P < 0.001). High-F dentifrice enhanced the bioavailability of salivary F, being an option for caries management in patients with high caries risk.

  2. DISSOLUTION OF LANTHANUM FLUORIDE PRECIPITATES

    DOEpatents

    Fries, B.A.

    1959-11-10

    A plutonium separatory ore concentration procedure involving the use of a fluoride type of carrier is presented. An improvement is given in the derivation step in the process for plutonium recovery by carrier precipitation of plutonium values from solution with a lanthanum fluoride carrier precipitate and subsequent derivation from the resulting plutonium bearing carrier precipitate of an aqueous acidic plutonium-containing solution. The carrier precipitate is contacted with a concentrated aqueous solution of potassium carbonate to effect dissolution therein of at least a part of the precipitate, including the plutonium values. Any remaining precipitate is separated from the resulting solution and dissolves in an aqueous solution containing at least 20% by weight of potassium carbonate. The reacting solutions are combined, and an alkali metal hydroxide added to a concentration of at least 2N to precipitate lanthanum hydroxide concomitantly carrying plutonium values.

  3. Silicon oxidation in fluoride solutions

    NASA Technical Reports Server (NTRS)

    Sancier, K. M.; Kapur, V.

    1980-01-01

    Silicon is produced in a NaF, Na2SiF6, and Na matrix when SiF4 is reduced by metallic sodium. Hydrogen is evolved during acid leaching to separate the silicon from the accompanying reaction products, NaF and Na2SiF6. The hydrogen evolution reaction was studied under conditions simulating leaching conditions by making suspensions of the dry silicon powder in aqueous fluoride solutions. The mechanism for the hydrogen evolution is discussed in terms of spontaneous oxidation of silicon resulting from the cooperative effects of (1) elemental sodium in the silicon that reacts with water to remove a protective silica layer, leaving clean reactive silicon, and (2) fluoride in solution that complexes with the oxidized silicon in solution and retards formation of a protective hydrous oxide gel.

  4. Acceleration of barium ions near 8000 km above an aurora

    NASA Technical Reports Server (NTRS)

    Stenbaek-Nielsen, H. C.; Hallinan, T. J.; Wescott, E. M.; Foeppl, H.

    1984-01-01

    A barium shaped charge, named Limerick, was released from a rocket launched from Poker Flat Research Range, Alaska, on March 30, 1982, at 1033 UT. The release took place in a small auroral breakup. The jet of ionized barium reached an altitude of 8100 km 14.5 min after release, indicating that there were no parallel electric fields below this altitude. At 8100 km the jet appeared to stop. Analysis shows that the barium at this altitude was effectively removed from the tip. It is concluded that the barium was actually accelerated upward, resulting in a large decrease in the line-of-sight density and hence the optical intensity. The parallel electric potential in the acceleration region must have been greater than 1 kV over an altitude interval of less than 200 km. The acceleration region, although presumably auroral in origin, did not seem to be related to individual auroral structures, but appeared to be a large-scale horizontal structure. The perpendicular electric field below, as deduced from the drift of the barium, was temporally and spatially very uniform and showed no variation related to individual auroral structures passing through.

  5. Preparation of barium hexaferrite powders using oxidized steel scales waste

    NASA Astrophysics Data System (ADS)

    Septiani, Ardita; Idayanti, Novrita; Kristiantoro, Tony

    2016-02-01

    Research on preparation of barium hexaferrite powders has been done using Hot Strip Mill scales as raw materials. Hot Strip Mill scales are oxidized steel scales waste from steel industrial process. The method used for preparing the barium hexaferrite powders was solid state reaction method. Oxidized steel scales were milled using ball mill for 10 hours, then screened through a 250 mesh sieve to obtain powders with maximum size of 63 µm. Powders were roasted at 600°C temperature for 4 hours to obtain hematite (Fe2O3) phase. Roasted powders were then mixed with barium carbonate, and were subsequently milled for 16 hours. After mixing, powders were calcined with an increasing rate of 10°C/min and maintained at 1100°C for 3 hours. Calcination process was performed to acquire barium hexaferrite phase. X-ray Diffraction (XRD) characterization in conjunction with RIR analysis showed that 85 wt. % of barium hexaferrite is formed. The magnetic properties of powders were characterized using Permagraph. It is found the value of remanent induction is 1.09 kG, coercivity of 2.043 kOe, and the maximum energy product of 0.25 MGOe.

  6. FLUORIDATION CHEMISTRY: EQUILIBRIA AND KINETICS OF FLUORIDE AND FLUORO-COMPLEXES

    EPA Science Inventory

    The most common fluoridating agents used by major American waterworks are hexafluorosilicic acid (H2SiF6) and sodium hexxafluorosilicate (Na2SiF6). According to the 1992 Water Fluoridation Census where 10,002 utilities responded affirmatively to fluoridating their water, 59
    % ...

  7. Compressive strength, fluoride release and recharge of fluoride-releasing materials.

    PubMed

    Xu, Xiaoming; Burgess, John O

    2003-06-01

    The compressive strength, fluoride releases and recharge profiles of 15 commercial fluoride-releasing restorative materials have been studied. The materials include glass ionomers (Fuji IX, Ketac Molar, Ketac Silver, and Miracle Mix), resin-modified glass ionomers (Fuji II LC Improved, Photac-Fil, and Vitremer), compomers (Compoglass, Dyract AP, F2000, and Hytac) and composite resins (Ariston pHc, Solitaire, Surefil and Tetric Ceram). A negative linear correlation was found between the compressive strength and fluoride release (r(2)=0.7741), i.e., restorative materials with high fluoride release have lower mechanical properties. The fluoride-releasing ability can be partially regenerated or recharged by using a topical fluoride agent. In general, materials with higher initial fluoride release have higher recharge capability (r(2)=0.7088). Five equations have been used in curve fitting to describe the cumulative fluoride release from different materials. The equation [F](c)=[F](I)(1-e(-bt))+betat best describes the cumulative fluoride release for most glass ionomers, resin-modified glass ionomers, and some high fluoride-releasing compomers and composites, whereas [F](c)=[F](I)/(t(1/2)+t)+alphat best describes the cumulative fluoride release for most compomers and composite resins. The clinic applications of different fluoride-releasing materials have also been discussed.

  8. PRECIPITATION OF URANIUM PEROXIDE OF LOW FLUORIDE CONTENT FROM SOLUTIONS CONTAINING FLUORIDES

    DOEpatents

    King, E.J.; Clark, H.M.

    1958-08-12

    S>A method is described for the preparation of fluoride free uraniunn peroxide precipitates, even though the solution from which the precipitation is made is contaminated with fluorides. This is accomplished by add ing aluminum ions to the solution, where they complex any fluoride present and prevent its precipitation with the uramum peroxide.

  9. Rocket having barium release system to create ion clouds in the upper atmosphere

    NASA Technical Reports Server (NTRS)

    Lewis, B. W.; Stokes, C. S.; Smith, E. W.; Murphy, W. J. (Inventor)

    1974-01-01

    A chemical system for releasing a good yield of free barium atoms and barium ions to create ion clouds in the upper atmosphere and interplanetary space for the study of the geophysical properties of the medium is presented.

  10. Barium Depletion in the NSTAR Discharge Cathode After 30,000 Hours of Operation

    NASA Technical Reports Server (NTRS)

    Polk, James E.; Capece, Angela M.; Mikellides, Ioannis G.; Katz, Ira

    2010-01-01

    Dispenser hollow cathodes rely on a consumable supply of barium released by impregnant materials in the pores of a tungsten matrix to maintain a low work function surface. Examinations of cathode inserts from long duration ion engine tests show deposits of tungsten at the downstream end that appear to block the flow of barium from the interior. In addition, a numerical model of barium transport in the insert plasma indicates that the barium partial pressure in the insert may exceed the equilibrium vapor pressure of the dominant barium-producing reaction, and it was postulated previously that this would suppress barium loss in the upstream part of the insert. New measurements of the depth of barium depletion from a cathode insert operated for 30,352 hours reveal that barium loss is confined to a narrow region near the downstream end, confirming this hypothesis.

  11. Topical use of fluorides for caries control.

    PubMed

    Pessan, Juliano Pelim; Toumba, Kyriacos Jack; Buzalaf, Marília Afonso Rabelo

    2011-01-01

    Since the early findings on the protective effects of fluoride present in drinking water upon caries incidence and prevalence, intensive research has been conducted in order to determine the benefits, safety, as well as the cost-effectiveness of other modalities of fluoride delivery. The present chapter reviews the various forms of topical fluoride use - professionally and self-applied - with special emphasis on clinical efficacy and possible side effects. The most widely used forms of fluoride delivery have been subject of several systematic reviews, providing strong evidence supporting the use of dentifrices, gels, varnishes and mouth rinses for the control of caries progression. Dentifrices with fluoride concentrations of 1,000 ppm and above have been shown to be clinically effective in caries prevention when compared to a placebo treatment, but the evidence regarding formulations with 450-550 ppm is still subject of debate. Therefore, the recommendation for low-fluoride dentifrice use must take into account both risks and benefits. The evidence for the combined use of two modalities of fluoride application in comparison to a single modality is still inconsistent, implying that more studies with adequate methodology are needed to determine the real benefits of each method. Considering the currently available evidence and risk-benefit aspects, it seems justifiable to recommend the use of fluoridated dentifrices to individuals of all ages, and additional fluoride therapy should also be targeted towards individuals at high caries risk.

  12. Barium Levels in Soils and Centella asiatica

    PubMed Central

    Ong, Ghim Hock; Yap, Chee Kong; Mahmood, Maziah; Tan, Soon Guan; Hamzah, Suhaimi

    2013-01-01

    In this study, Centella asiatica and surface soils were collected from 12 sampling sites in Peninsular Malaysia, and the barium (Ba) concentrations were determined. The Ba concentration [μg/g dry weight (dw)] was 63.72 to 382.01 μg/g in soils while in C. asiatica, Ba concentrations ranged from 5.05 to 21.88 μg/g for roots, 3.31 to 11.22 μg/g for leaves and 2.37 to 6.14 μg/g for stems. In C. asiatica, Ba accumulation was found to be the highest in roots followed by leaves and stems. The correlation coefficients (r) of Ba between plants and soils were found to be significantly positively correlated, with the highest correlation being between roots-soils (r=0.922, p<005), followed by leaves-soils (r=0.890, p<005) and stems-soils (r=0.848, p<005). This indicates that these three parts of C. asiatica are good biomonitors of Ba pollution. For the transplantation study, four sites were selected as unpolluted [(Universiti Putra Malaysia (UPM)], semi-polluted (Seri Kembangan and Balakong) and polluted sites (Juru). Based on the transplantation study under experimental field and laboratory conditions, Ba concentrations in C. asiatica were significantly (p<0.05) higher after three weeks of exposure at Seri Kembangan, Balakong and Juru. Thus, these experimental findings confirm that the leaves, stems and roots of C. asiatica can reflect the Ba levels in the soils where this plant is found. Three weeks after back transplantation to clean soils, the Ba levels in C. asiatica were still higher than the initial Ba level even though Ba elimination occurred. In conclusion, the leaves, stems and roots of C. asiatica are good biomonitors of Ba pollution. PMID:24575242

  13. Selectivity in biomineralization of barium and strontium.

    PubMed

    Krejci, Minna R; Wasserman, Brian; Finney, Lydia; McNulty, Ian; Legnini, Daniel; Vogt, Stefan; Joester, Derk

    2011-11-01

    The desmid green alga Closterium moniliferum belongs to a small number of organisms that form barite (BaSO(4)) or celestite (SrSO(4)) biominerals. The ability to sequester Sr in the presence of an excess of Ca is of considerable interest for the remediation of (90)Sr from the environment and nuclear waste. While most cells dynamically regulate the concentration of the second messenger Ca(2+) in the cytosol and various organelles, transport proteins rarely discriminate strongly between Ca, Sr, and Ba. Herein, we investigate how these ions are trafficked in C. moniliferum and how precipitation of (Ba,Sr)SO(4) crystals occurs in the terminal vacuoles. Towards this goal, we simultaneously visualize intracellular dynamics of multiple elements using X-ray fluorescence microscopy (XFM) of cryo-fixed/freeze-dried samples. We correlate the resulting elemental maps with ultrastructural information gleaned from freeze-fracture cryo-SEM of frozen-hydrated cells and use micro X-ray absorption near edge structure (micro-XANES) to determine sulfur speciation. We find that the kinetics of Sr uptake and efflux depend on external Ca concentrations, and Sr, Ba, and Ca show similar intracellular localization. A highly ion-selective cross-membrane transport step is not evident. Based on elevated levels of sulfate detected in the terminal vacuoles, we propose a "sulfate trap" model, where the presence of dissolved barium leads to preferential precipitation of (Ba,Sr)SO(4) due to its low solubility relative to SrSO(4) and CaSO(4). Engineering the sulfate concentration in the vacuole may thus be the most direct way to increase the Sr sequestered per cell, an important consideration in using desmids for phytoremediation of (90)Sr.

  14. Interfacial reactions and microstructure of BaTiO 3 films prepared using fluoride precursor method

    NASA Astrophysics Data System (ADS)

    Fujihara, Shinobu; Schneller, Theodor; Waser, Rainer

    2004-01-01

    Interfacial reactions of BaF 2 and TiO 2 were investigated in preparing BaTiO 3 thin films using a fluoride precursor method. Trifluoroacetate solutions were prepared from barium acetate, titanium tetraisopropoxide (TTIP), and trifluoroacetic acid (TFA, CF 3COOH) with additives such as water and acetylacetone. The solutions were deposited on platinized Si wafers by spin-coating, were pyrolysed at 400 °C in air and were finally heated typically at 700 °C in a water vapor atmosphere. The perovskite BaTiO 3 phase was obtained although a small portion of BaF 2 remained unreacted. Thus, the films were characterized as the mixture of BaTiO 3, BaF 2, and amorphous TiO 2. Influence of the solution chemistry on the phase evolution and microstructure was examined in order to discuss the reaction pathway of the perovskite phase.

  15. Electro-optical polycrystalline barium lanthanum titanium niobate

    SciTech Connect

    Mehrotra, A.K.

    1991-02-19

    This patent describes a transparent electro-optic article. It comprises: of a barium lanthanum titanium niobate wherein substantially all grains are of a grain size between about 2 and about 20 micron, the article has a pore volume of less than about 1 percent, and the article has a grain size of between about 2 and about 20 microns. This patent also describes a method of forming transparent electro-optical barium lanthanum titanium niobate. It comprises: providing particles of barium carbonate, lanthanum oxide, titanium oxide, and niobium oxide, calcining the particles, sintering the calcined particles at a temperature of between about 1200{degrees} C and 1300{degrees} C. and a vacuum of between about 10{sup {minus}3} and 10{sup {minus}4} torr while under pressure to form a sintered mass, cooling the sintered mass, slicing the mass to form wafers, heating the wafers in an oxidizing atmosphere.

  16. Multiphoton laser ionization for energy conversion in barium vapor

    NASA Astrophysics Data System (ADS)

    Makdisi, Y.; Kokaj, J.; Afrousheh, K.; Mathew, J.; Nair, R.; Pichler, G.

    2013-03-01

    We have studied the ion detection of barium atoms in special heated ovens with a tungsten rod in the middle of the stainless steel tube. The tungsten rod was heated indirectly by the oven body heaters. A bias voltage between the cell body and the tungsten rod of 9 V was used to collect electrons, after the barium ions had been created. However, we could collect the electrons even without the bias voltage, although with ten times less efficiency. We studied the conditions for the successful bias-less thermionic signal detection using excimer/dye laser two-photon excitation of Rydberg states below and above the first ionization limit (two-photon wavelength at 475.79 nm). We employed a hot-pipe oven and heat-pipe oven (with inserted mesh) in order to generate different barium vapor distributions inside the oven. The thermionic signal increased by a factor of two under heat-pipe oven conditions.

  17. Prompt ionization in the CRIT II barium releases

    NASA Astrophysics Data System (ADS)

    Torbert, R. B.; Kletzing, C. A.; Liou, K.; Rau, D.

    1992-05-01

    Observations of electron and ion distributions inside a fast neutral barium jet in the ionosphere show significant fluxes within 4 km of release, presumably related to beam plasma instability processes involved in the Critical Ionization Velocity (CIV) effect. Electron fluxes exceeding 5 x 10 exp 12/sq cm-str-sec-keV were responsible for ionizing both the streaming barium and ambient oxygen. Resulting ion fluxes seem to be consistent with 1-2 percent ionization of the fast barium, as reported by optical observations, although the extended spatial distribution of the optically observed ions is difficult to reconcile with the in situ observations. When the perpendicular velocity of the neutrals falls below critical values, these processes shut off. Although these observations resemble the earlier Porcupine experimental results (Haerendel, 1982), theoretical understanding of the differences between these data and that of earlier negative experiments is still lacking.

  18. Barium-borate-flyash glasses: As radiation shielding materials

    NASA Astrophysics Data System (ADS)

    Singh, Sukhpal; Kumar, Ashok; Singh, Devinder; Thind, Kulwant Singh; Mudahar, Gurmel S.

    2008-01-01

    The attenuation coefficients of barium-borate-flyash glasses have been measured for γ-ray photon energies of 356, 662, 1173 and 1332 keV using narrow beam transmission geometry. The photon beam was highly collimated and overall scatter acceptance angle was less than 3°. Our results have an uncertainty of less than 3%. These coefficients were then used to obtain the values of mean free path (mfp), effective atomic number and electron density. Good agreements have been observed between experimental and theoretical values of these parameters. From the studies of the obtained results it is reported here that from the shielding point of view the barium-borate-flyash glasses are better shields to γ-radiations in comparison to the standard radiation shielding concretes and also to the ordinary barium-borate glasses.

  19. Long-term in vitro fluoride release and rerelease from orthodontic bonding materials containing fluoride.

    PubMed

    Cohen, Warren J; Wiltshire, William A; Dawes, Colin; Lavelle, Chris L B

    2003-11-01

    The purpose of this study was to compare in vitro long-term (30 month) fluoride release and rerelease rates (after fluoride exposure) from 3 orthodontic bonding materials containing fluoride and 1 without fluoride. Ten samples of each material (Python, TP Orthodontics, LaPorte, Ind; Assure, Reliance Orthodontic Products, Itasca, Ill; Fuji Ortho LC, GC America, Alsip, Ill; and Transbond XT, 3M Unitek, Monrovia, Calif) were fabricated and stored in deionized distilled water at 37 degrees C. Five samples had fluoride-release rates measured at days 546, 637, 730, 821, and 913 after initial fabrication, and 5 samples were exposed to fluoride (Nupro 2% NaF gel, Dentsply Canada, Woodbridge, Ontario, Canada) for 4 minutes at day 535 and had measurements taken on days 546, 548, 552, 575, 637, 730, 821, and 913. To prevent cumulative measurements, the storage solutions were changed 24 hours before measurement. Statistically significant differences were found in fluoride-release rates (P <.0001), with Fuji Ortho LC releasing the most fluoride, followed by Python and Assure at all time points in the nonfluoride exposed group. In the fluoride-exposed group, there were significant differences in fluoride release (P <.0001), with Fuji Ortho LC releasing the most fluoride. A "burst-effect" pattern of fluoride release was seen after fluoride exposure for all materials. It was concluded that Fuji Ortho LC, Assure, and Python might have sufficient long-term fluoride-release rates to reduce white spot formation, and all are recommended as suitable fluoride-releasing orthodontic bonding materials.

  20. Phenotypic and behavioral defects caused by barium exposure in nematode Caenorhabditis elegans.

    PubMed

    Wang, D-Y; Wang, Y

    2008-04-01

    To examine the possible phenotypic defects from barium exposure, a model organism, Caenorhabditis elegans, was chosen to analyze the multiple toxicities in barium-exposed animals. Endpoints of life span, body size, brood size, generation time, head thrash, and body bend were selected for the assessment of barium toxicity. High concentrations (75 microM and 200 microM) of barium exposure caused severe life-span defects. Body sizes of exposed animals were markedly reduced compared to the controls, and high concentrations of barium exposure (75 microM and 200 microM) caused the appearance of vulva abnormality. In addition, barium exposure resulted in severe defects in reproductive capacity and reproductive speed. Body bends and head thrashes were also severely impaired after barium exposure. Furthermore, the stress responses to barium exposure suggest severe barium toxicity. The observed severe locomotion behavior and life-span defects in nematodes might be largely due to the deposition of barium toxicity in the muscle and intestine systems, respectively. Our data suggest that barium exposure could cause multiple biological defects by affecting the life span, development, reproduction, and locomotion behaviors. These multiple biological defects provide a new evaluation system to monitor the toxicity from barium exposure.

  1. Volatile Barium Beta-Diketonate Polyether Adducts. Synthesis, Characterization and Metalorganic Chemical Vapor Deposition

    DTIC Science & Technology

    1991-05-31

    Volatile Barium 13- Diketonate Polyether Adducts.... Synthesis , Characterization and Metalorganic Chemical Vapor Deposition by Robin A. Gardiner...has been approved for public release and sale: its distribution is unlimited. Volatile, Barium B- Diketonate Polyether Adducts. Synthesis ...NO. NO. INO. ACCESSION NO. Arlington, VA 22217 II 11. TITLE (include Security Classification) Volatile Barium B- Diketonate Polyether Adducts

  2. 40 CFR 721.10010 - Barium manganese oxide (BaMnO3).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Barium manganese oxide (BaMnO3). 721... Substances § 721.10010 Barium manganese oxide (BaMnO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as barium manganese oxide (BaMnO3) (PMN...

  3. 40 CFR 721.10010 - Barium manganese oxide (BaMnO3).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Barium manganese oxide (BaMnO3). 721... Substances § 721.10010 Barium manganese oxide (BaMnO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as barium manganese oxide (BaMnO3) (PMN...

  4. 40 CFR 721.10010 - Barium manganese oxide (BaMnO3).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Barium manganese oxide (BaMnO3). 721... Substances § 721.10010 Barium manganese oxide (BaMnO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as barium manganese oxide (BaMnO3) (PMN...

  5. 40 CFR 721.10010 - Barium manganese oxide (BaMnO3).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Barium manganese oxide (BaMnO3). 721... Substances § 721.10010 Barium manganese oxide (BaMnO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as barium manganese oxide (BaMnO3) (PMN...

  6. Measurement of Elastic Modulus of Alumina and Barium Strontium Titanate Wafers Produced by Tape Casting Method

    DTIC Science & Technology

    2014-02-01

    UNCLASSIFIED AD-E403 481 Technical Report ARMET-TR-12039 MEASUREMENT OF ELASTIC MODULUS OF ALUMINA AND BARIUM STRONTIUM ...DATES COVERED (From – To) 4. TITLE AND SUBTITLE MEASUREMENT OF ELASTIC MODULUS OF ALUMINA AND BARIUM STRONTIUM TITANATE WAFERS PRODUCED BY...configuration testing method. Samples of barium strontium titanate (BST) were made using a regular powder pressing, sintering, pelletizing, and

  7. Compact pulse forming line using barium titanate ceramic material

    NASA Astrophysics Data System (ADS)

    Kumar Sharma, Surender; Deb, P.; Shukla, R.; Prabaharan, T.; Shyam, A.

    2011-11-01

    Ceramic material has very high relative permittivity, so compact pulse forming line can be made using these materials. Barium titanate (BaTiO3) has a relative permittivity of 1200 so it is used for making compact pulse forming line (PFL). Barium titanate also has piezoelectric effects so it cracks during high voltages discharges due to stresses developed in it. Barium titanate is mixed with rubber which absorbs the piezoelectric stresses when the PFL is charged and regain its original shape after the discharge. A composite mixture of barium titanate with the neoprene rubber is prepared. The relative permittivity of the composite mixture is measured to be 85. A coaxial pulse forming line of inner diameter 120 mm, outer diameter 240 mm, and length 350 mm is made and the composite mixture of barium titanate and neoprene rubber is filled between the inner and outer cylinders. The PFL is charged up to 120 kV and discharged into 5 Ω load. The voltage pulse of 70 kV, 21 ns is measured across the load. The conventional PFL is made up of oil or plastics dielectrics with the relative permittivity of 2-10 [D. R. Linde, CRC Handbook of Chemistry and Physics, 90th ed. (CRC, 2009); Xia et al., Rev. Sci. Instrum. 79, 086113 (2008); Yang et al., Rev. Sci. Instrum. 81, 43303 (2010)], which increases the length of PFL. We have reported the compactness in length achieved due to increase in relative permittivity of composite mixture by adding barium titanate in neoprene rubber.

  8. Fluorescent sensing of fluoride in cellular system.

    PubMed

    Jiao, Yang; Zhu, Baocun; Chen, Jihua; Duan, Xiaohong

    2015-01-01

    Fluoride ions have the important roles in a lot of physiological activities related with biological and medical system, such as water fluoridation, caries treatment, and bone disease treatment. Great efforts have been made to develop new methods and strategies for F(-) detection in the past decades. Traditional methods for the detection of F(-) including ion chromatography, ion-selective electrodes, and spectroscopic techniques have the limitations in the biomedicine research. The fluorescent probes for F(-) are very promising that overcome some drawbacks of traditional fluoride detection methods. These probes exhibit high selectivity, high sensitivity as well as quick response to the detection of fluoride anions. The review commences with a brief description of photophysical mechanisms for fluorescent probes for fluoride, including photo induced electron transfer (PET), intramolecular charge transfer (ICT), fluorescence resonance energy transfer (FRET), and excited-state intramolecular proton transfer (ESIPT). Followed by a discussion about common dyes for fluorescent fluoride probes, such as anthracene, naphalimide, pyrene, BODIPY, fluorescein, rhodamine, resorufin, coumarin, cyanine, and near-infrared (NIR) dyes. We divide the fluorescent probes for fluoride in cellular application systems into nine groups, for example, type of hydrogen bonds, type of cleavage of Si-O bonds, type of Si-O bond cleavage and cylization reactions, etc. We also review the recent reported carriers in the delivery of fluorescent fluoride probes. Seventy-four typical fluorescent fluoride probes are listed and compared in detail, including quantum yield, reaction medium, excitation and emission wavelengths, linear detection range, selectivity for F(-), mechanism, and analytical applications. Finally, we discuss the future challenges of the application of fluorescent fluoride probes in cellular system and in vivo. We wish that more and more excellent fluorescent fluoride probes will be

  9. Fluorescent Sensing of Fluoride in Cellular System

    PubMed Central

    Jiao, Yang; Zhu, Baocun; Chen, Jihua; Duan, Xiaohong

    2015-01-01

    Fluoride ions have the important roles in a lot of physiological activities related with biological and medical system, such as water fluoridation, caries treatment, and bone disease treatment. Great efforts have been made to develop new methods and strategies for F- detection in the past decades. Traditional methods for the detection of F- including ion chromatography, ion-selective electrodes, and spectroscopic techniques have the limitations in the biomedicine research. The fluorescent probes for F- are very promising that overcome some drawbacks of traditional fluoride detection methods. These probes exhibit high selectivity, high sensitivity as well as quick response to the detection of fluoride anions. The review commences with a brief description of photophysical mechanisms for fluorescent probes for fluoride, including photo induced electron transfer (PET), intramolecular charge transfer (ICT), fluorescence resonance energy transfer (FRET), and excited-state intramolecular proton transfer (ESIPT). Followed by a discussion about common dyes for fluorescent fluoride probes, such as anthracene, naphalimide, pyrene, BODIPY, fluorescein, rhodamine, resorufin, coumarin, cyanine, and near-infrared (NIR) dyes. We divide the fluorescent probes for fluoride in cellular application systems into nine groups, for example, type of hydrogen bonds, type of cleavage of Si-O bonds, type of Si-O bond cleavage and cylization reactions, etc. We also review the recent reported carriers in the delivery of fluorescent fluoride probes. Seventy-four typical fluorescent fluoride probes are listed and compared in detail, including quantum yield, reaction medium, excitation and emission wavelengths, linear detection range, selectivity for F-, mechanism, and analytical applications. Finally, we discuss the future challenges of the application of fluorescent fluoride probes in cellular system and in vivo. We wish that more and more excellent fluorescent fluoride probes will be developed

  10. Ionization and expansion of barium clouds in the ionosphere

    NASA Technical Reports Server (NTRS)

    Ma, T.-Z.; Schunk, R. W.

    1993-01-01

    A recently envelope 3D model is used here to study the motion of the barium clouds released in the ionosphere, including the ionization stage. The ionization and the expansion of the barium clouds and the interaction between the clouds and the background ions are investigated using three simulations: a cloud without a directional velocity, a cloud with an initial velocity of 5 km/s across the B field, and a cloud with initial velocity components of 2 km/s both along and across the B field.

  11. Study of the photovoltaic effect in thin film barium titanate

    NASA Technical Reports Server (NTRS)

    Grannemann, W. W.; Dharmadhikari, V. S.

    1981-01-01

    The photoelectric effect in structures consisting of metal deposited barium titanate film silicon is described. A radio frequency sputtering technique is used to deposit ferroelectric barium titantate films on silicon and quartz. Film properties are measured and correlated with the photoelectric effect characteristics of the films. It was found that to obtain good quality pin hole free films, it is necessary to reduce the substrate temperature during the last part of the deposition. The switching ability of the device with internal applied voltage is improved when applied with a ferroelectric memory device.

  12. Methods for producing monodispersed particles of barium titanate

    DOEpatents

    Hu, Zhong-Cheng

    2001-01-01

    The present invention is a low-temperature controlled method for producing high-quality, ultrafine monodispersed nanocrystalline microsphere powders of barium titanate and other pure or composite oxide materials having particles ranging from nanosized to micronsized particles. The method of the subject invention comprises a two-stage process. The first stage produces high quality monodispersed hydrous titania microsphere particles prepared by homogeneous precipitation via dielectric tuning in alcohol-water mixed solutions of inorganic salts. Titanium tetrachloride is used as an inorganic salt precursor material. The second stage converts the pure hydrous titania microsphere particles into crystalline barium titanate microsphere powders via low-temperature, hydrothermal reactions.

  13. Ferroelastic domains in lead-free barium zirconate titanate - barium calcium titanate piezoceramics

    NASA Astrophysics Data System (ADS)

    Ehmke, Matthias Claudius

    Piezoelectricity was first discovered by Pierre and Jaque Curie in the year 1880. Nowadays, piezoelectric materials are used in many application such as high voltage generation in gas igniters, actuation in micro-positioning devices, generation and detection of acoustic waves, emitters and receivers for sonar technology, ultrasonic cleaning, ultrasound medical therapy, and micropumps for ink-jet printers. The most commonly used piezoelectric material since the 1950's is the solid solution system lead zirconate titanate (PZT) that offers high piezoelectric performance under a large range of operating conditions. However, the toxicity of lead requires the replacement of PZT. The studied lead-free alternatives are commonly based on potassium sodium niobate (KNN) and bismuth sodium titanate (BNT), and more recently zirconium and calcium substituted barium titanate (BZT-BCT). The BZT-BCT system exhibits large piezoelectric coefficients that can exceed even those of most PZT compositions under certain conditions. Piezoelectricity was first discovered by Pierre and Jaque Curie in the year 1880. Nowadays, piezoelectric materials are used in many application such as high voltage generation in gas igniters, actuation in micro-positioning devices, generation and detection of acoustic waves, emitters and receivers for sonar technology, ultrasonic cleaning, ultrasound medical therapy, and micropumps for ink-jet printers. The most commonly used piezoelectric material since the 1950's is the solid solution system lead zirconate titanate (PZT) that offers high piezoelectric performance under a large range of operating conditions. However, the toxicity of lead requires the replacement of PZT. The studied lead-free alternatives are commonly based on potassium sodium niobate (KNN) and bismuth sodium titanate (BNT), and more recently zirconium and calcium substituted barium titanate (BZT-BCT). The BZT-BCT system exhibits large piezoelectric coefficients that can exceed even those of

  14. Comparative Evaluation of Longevity of Fluoride Release From three Different Fluoride Varnishes – An Invitro Study

    PubMed Central

    Roshan, NM; Poornima, P; Nagaveni, NB; Neena, IE; Bharath, KP

    2016-01-01

    Introduction Fluoride varnishes play a pivotal role in inhibition of dental caries by increasing remineralization. Aim To determine the longevity of fluoride release from 3 different fluoride varnishes over a period of time through salivary fluoride estimation. Materials and Methods Twenty four extracted human deciduous anterior teeth were divided into four groups, i.e., ClinproTM XT, Flouritop SR, Flourprotector and Control group. Fluoride varnishes were applied on 3mm x 3mm window on labial surface of the teeth and then the teeth were immersed and stored in artificial saliva. The concentration of fluoride in ppm was measured after 1 week, 1 month, 3 months and 6 months. Fluoride release at each time interval for different groups was statistically analyzed using ANOVA and Post Hoc Tukey’s test. Results Although all the fluoride varnishes released fluoride, with greatest release observed during 1st week by Fluoritop SR (66.92±16.30ppm), ClinproTM XT Varnish released consistently and substantially more fluoride than Fluoritop SR and Fluorprotector during 6 months analysis (p<0.05). Fluorprotector showed the lowest rate of F release among all the groups compared. Conclusion Over a period of 6 months ClinproTM XT Varnish released consistently and substantially more fluoride than other tested products. PMID:27656559

  15. Differences in loosely bound fluoride formation and anticaries effect of resin-based fluoride varnishes.

    PubMed

    Maas, Jorge R S; Junior, Italo M Faraco; Lodi, Carolina S; Delbem, Alberto C B

    2013-05-01

    OBJECTIVE.  Our in vitro study evaluated calcium fluoride formation in enamel and the anticaries effect of seven resin-based varnishes under cariogenic challenge. METHODS.  Enamel blocks were subjected to pH cycling. The experimental groups received fluoride varnish application, the positive control received topical fluoride gel treatment, and the negative control did not receive any treatment. The pH cycling surface hardness (SH1 ) and integrated loss of subsurface hardness (ΔKHN) were then determined. We measured the amount of fluoride released into the demineralizing and remineralizing (DE-RE) solutions used in pH cycling. The fluoride concentration in the enamel was determined 24 h after application of the products as loosely bound fluoride and firmly bound fluoride. RESULTS.  Higher deposits of loosely bound fluoride were observed for Duofluorid, followed by Biophat. For Duraphat, Bifluorid, Duraflur, and Duofluorid, no difference was observed in the SH1 and ΔKHN values, with the lowest mineral loss compared to the other groups. The Bifluorid and Duofluorid groups released high fluoride amounts into the DE-RE, and statistically significant difference was noted between them. CONCLUSIONS.  The anticaries effect showed no correlation with higher deposited fluoride amounts, resin type, or fluoride source.

  16. Fluoride intake and its safety among heavy tea drinkers in a British fluoridated city.

    PubMed

    Jenkins, G N

    1991-01-01

    Tea-drinking in very young children has been studied in a British city. The results suggested that the fluoride in tea would, in some cases, be sufficient to influence caries. Clinical findings to some extent supported this. The main purpose of the investigation reported here was to determine maximum possible fluoride intake in adults who were heavy tea drinkers in a fluoridated city and relate it to toxic thresholds. Heavy tea drinkers were traced through Health Visitors and voluntary organizations and the volumes and fluoride concentrations of their drinks were measured. Even the highest intake found (9 mg) is below the probable intake in Bartlett, Texas (8 ppm of fluoride), in relation to which no undesirable symptoms have been reported (Leone et al. 1954). This confirms the safety of fluoridation. The effects on fluoride concentration of evaporating soft and hard fluoride-containing waters to small bulk were compared. The results showed ceilings of 3 ppm of fluoride in hard water and about 14 ppm in soft water, much higher than the levels expected on the basis of the usually stated solubility of CaF2 (16 or 8 ppm of fluoride). However, under normal household conditions, it is most unlikely that dangerous levels of fluoride would be ingested from boiled water.

  17. Review on fluoride, with special emphasis on calcium fluoride mechanisms in caries prevention.

    PubMed

    ten Cate, J M

    1997-10-01

    Low concentrations of fluoride have a beneficial effect on enamel and dentin de- and remineralization. After fluoride treatments, such as topical applications, rinses or dentifrices, salivary fluoride concentrations decrease exponentially in a biphasic manner to very low concentrations within a few hours. For treatments to be effective over periods longer than the brushing and the following salivary clearance, fluoride needs to be deposited and slowly released. Calcium fluoride (or like) deposits act in such a way, owing to a surface covering of phosphate and/or proteins, which makes the CaF2 less soluble under in vivo conditions than in a pure form in inorganic solutions. Moreover, due to the phosphate groups on the surface of the calcium fluoride globules, fluoride is assumed to be released with decreasing pH when the phosphate groups are protonated in the dental plaque.

  18. Biomonitoring Equivalents for interpretation of urinary fluoride.

    PubMed

    Aylward, L L; Hays, S M; Vezina, A; Deveau, M; St-Amand, A; Nong, A

    2015-06-01

    Exposure to fluoride is widespread due to its natural occurrence in the environment and addition to drinking water and dental products for the prevention of dental caries. The potential health risks of excess fluoride exposure include aesthetically unacceptable dental fluorosis (tooth mottling) and increased skeletal fragility. Numerous organizations have conducted risk assessments and set guidance values to represent maximum recommended exposure levels as well as recommended adequate intake levels based on potential public health benefits of fluoride exposure. Biomonitoring Equivalents (BEs) are estimates of the average biomarker concentrations corresponding to such exposure guidance values. The literature on daily urinary fluoride excretion rates as a function of daily fluoride exposure was reviewed and BE values corresponding to the available US and Canadian exposure guidance values were derived for fluoride in urine. The derived BE values range from 1.1 to 2.1mg/L (1.2-2.5μg/g creatinine). Concentrations of fluoride in single urinary spot samples from individuals, even under exposure conditions consistent with the exposure guidance values, may vary from the predicted average concentrations by several-fold due to within- and across-individual variation in urinary flow and creatinine excretion rates and due to the rapid elimination kinetics of fluoride. Thus, the BE values are most appropriately applied to screen population central tendency estimates for biomarker concentrations rather than interpretation of individual spot sample concentrations.

  19. Fluoride effects: the two faces of janus.

    PubMed

    Gazzano, E; Bergandi, L; Riganti, C; Aldieri, E; Doublier, S; Costamagna, C; Bosia, A; Ghigo, D

    2010-01-01

    The behavior of fluoride ions in the human organism is a classic example of double-edged sword. On the one hand the daily supplementation with fluoride is undoubtedly an important preventing factor in protecting teeth from caries, and, as an important mitogenic stimulus for osteoblasts, it may enhance mineral deposition in bone, but on the other hand fluoride, above a threshold concentration, has been demonstrated to be toxic. We present here a brief review of fluoride metabolism and exposure, its use in caries prevention and its effects on bone, followed by an updating about the main hypotheses concerning its mechanism of action and toxicity. The effects of fluoride have been related mainly to its ability to evoke the activation of G proteins and the inhibition of phosphotyrosine phosphatases, leading to an intracellular increase of tyrosine phosphorylation and activation of the mitogen-activated protein kinase pathway, and its capacity to cause generation of reactive oxygen species. We present also a unifying hypothesis accounting for these apparently different effects, although the available experimental models and conditions are highly variable in the literature. A lot of experiments still need to be performed to clarify the positive and negative effects of fluoride. Finding the mechanisms accounting for fluoride toxicity is an important point: indeed, the use of fluoride has been proposed in the preparation of new biomaterials to be inserted in the bone, in order to improve their stable and safe integration.

  20. Method of making porous ceramic fluoride

    DOEpatents

    Reiner, Robert H.; Holcombe, Cressie E.

    1990-01-01

    A process for making a porous ceramic composite where fumed silica particles are coated with a nitrate, preferably aluminum nitrate. Next the nitrate is converted to an oxide and formed into a desired configuration. This configuration is heated to convert the oxide to an oxide silicate which is then react with HF, resulting in the fluoride ceramic, preferably aluminum fluoride.

  1. Growth of hollow nickel fluoride whiskers

    SciTech Connect

    Petrov, S. V.; Orekhov, Yu. F.; Fedorov, P. P.

    2009-07-15

    Hollow nickel fluoride whiskers have been obtained by condensation from the vapor phase onto a platinum substrate in a flow of hydrogen fluoride. Crystals up to 5 mm in length have a square cross section with a 300 {+-} 30-{mu}m side. The wall thickness is 85 {+-} 20 {mu}m.

  2. Xenon fluoride solutions effective as fluorinating agents

    NASA Technical Reports Server (NTRS)

    Hyman, H. H.; Quarterman, L. A.; Sheft, I.

    1967-01-01

    Solutions of xenon fluorides in anhydrous hydrogen fluoride have few disruptive effects and leave a residue consisting of gaseous xenon, which can be recovered and refluorinated. This mild agent can be used with materials which normally must be fluorinated with fluorine alone at high temperatures.

  3. Discovery of Interstellar Hydrogen Fluoride

    NASA Technical Reports Server (NTRS)

    Neufeld, David A.; Zmuidzinas, Jonas; Schilke, Peter; Phillips, Thomas G.

    1997-01-01

    We report the first detection of interstellar hydrogen fluoride. Using the Long Wavelength Spectrometer of the Infrared Space Observatory (ISO), we have detected the 121.6973 micron J = 2-1 line of HF in absorption toward the far-infrared continuum source Sagittarius B2. The detection is statistically significant at the 13 sigma level. On the basis of our model for the excitation of HF in Sgr B2, the observed line equivalent width of 1.0 nm implies a hydrogen fluoride abundance of approximately 3 x 10(exp -10) relative to H2. If the elemental abundance of fluorine in Sgr B2 is the same as that in the solar system, then HF accounts for approximately 2% of the total number of fluorine nuclei. We expect hydrogen fluoride to be the dominant reservoir of gas-phase fluorine in Sgr B2, because it is formed rapidly in exothermic reactions of atomic fluorine with either water or molecular hydrogen; thus, the measured HF abundance suggests a substantial depletion of fluorine onto dust grains. Similar conclusions regarding depletion have previously been reached for the case of chlorine in dense interstellar clouds. We also find evidence at a lower level of statistical significance (approximately 5 sigma) for an emission feature at the expected position of the 4(sub 32)-4(sub 23) 121.7219 micron line of water. The emission-line equivalent width of 0.5 nm for the water feature is consistent with the water abundance of 5 x 10(exp -6) relative to H2 that has been inferred previously from observations of the hot core of Sgr B2.

  4. Discovery of Interstellar Hydrogen Fluoride

    NASA Technical Reports Server (NTRS)

    Neufeld, David A.; Zmuidzinas, Jonas; Schilke, Peter; Phillips, Thomas G.

    1997-01-01

    We report the first detection of interstellar hydrogen fluoride. Using the Long Wavelength Spectrometer of the Infrared Space Observatory (ISO), we have detected the 121.6973 micron J = 2-1 line of HF in absorption toward the far-infrared continuum source Sagittarius B2. The detection is statistically significant at the 13 sigma level. On the basis of our model for the excitation of HF in Sgr B2, the observed line equivalent width of 1.0 nm implies a hydrogen fluoride abundance of about 3 x 10 (exp -10) relative to H, If the elemental abundance of fluorine in Sgr B2 is the same as that in the solar system, then HF accounts for about 2% of the total number of fluorine nuclei. We expect hydrogen fluoride to be the dominant reservoir of gas-phase fluorine in Sgr B2, because it is formed rapidly in exothermic reactions of atomic fluorine with either water or molecular hydrogen; thus, the measured HF abundance suggests a substantial depletion of fluorine onto dust grains. Similar conclusions regarding depletion have previously been reached for the case of chlorine in dense interstellar clouds. We also find evidence at a lower level of statistical significance (about 5 sigma) for an emission feature at the expected position of the 4(sub 32)-4(sub 23) 121.7219 micron line of water. The emission-line equivalent width of 0.5 mm for the water feature is consistent with the water abundance of 5 x 10(exp -6) relative to H, that has been inferred previously from observations of the hot core of Sgr B2.

  5. Effects of daily fluoride exposures on fluoride release by glass ionomer-based restoratives.

    PubMed

    Freedman, Rick; Diefenderfer, Kim E

    2003-01-01

    It is well documented that glass ionomer cements absorb and release fluoride following single fluoride exposures. This study examined fluoride release among three glass ionomer-based restorative materials following multiple daily exposures to three topical fluoride regimens. Using a Delrin mold, 32 cylindrical specimens, each of a glass ionomer (Ketac-Fil), resin-modified glass ionomer (Photac-Fil) and polyacid-modified resin (Dyract AP) were created. Each specimen was subjected to one of four daily treatments (n = 8): (1) no fluoride treatment (control); (2) application of a fluoride dentifrice (1000 ppm) for one minute once daily; (3) application of the same dentifrice for one minute twice daily; (4) the same regimen as (3), plus immersion in a 0.05% sodium fluoride (NaF) mouth rinse (225 ppm) for one minute immediately following the second dentifrice application. Each specimen was suspended in a polyethylene test tube containing 1.0 ml demineralizing solution (pH 4.3) at 37 degrees C for six hours, then transferred to a new test tube containing 1.0 ml remineralizing solution (pH 7.0) at 37 degrees C for 18 hours. Fluoride treatments were completed at the time of transfer daily for seven days. Media solutions were buffered with equal volumes of TISAB II; fluoride levels were measured using a digital ion analyzer and fluoride electrode. Fluoride release decreased significantly from Day 1 to Day 3 for all materials regardless of fluoride treatment (Repeated Measures ANOVA, Tukey HSD, p < 0.05). All specimens released significantly more fluoride in demineralizing solution than in remineralizing solution. For Days 2-7, Treatment 4 produced greater fluoride release than both the control and Treatment 2 for all three materials (p < 0.05); For each material, the fluoride release produced by Treatments 3 and 4 was statistically similar on most days throughout the study. By Day 7, Photac-Fil demonstrated both the greatest total fluoride release and the greatest

  6. Manufacture and properties of fluoride cement

    NASA Astrophysics Data System (ADS)

    Malata-Chirwa, Charles David

    This research work aimed at characterising composition, hydration and physical properties of fluoride cement, by studying samples of the cement obtained from Malawi, and comparing them to ordinary Portland cement. By confirming the suitable characteristics of fluoride cement through this work, the results of the research work provide a good basis for the wider adoption of fluoride cement as an alternative to ordinary Portland cement, especially in developing economies. Numerous accounts have been cited regarding the production and use of fluoride cement. Since there have not been conclusive agreement as to its properties, this study was limited to the theories of successful incorporation of fluoride compounds in the manufacture of fluoride cement. Hence, the properties and characteristics reported in this study relate to the cement currently manufactured in Malawi, and, on a comparative basis only, to that manufactured in other parts of the world. Samples of the fluoride cement used in the study were obtained by synthetic manufacture of the cement using common raw materials for the manufacture of fluoride cement that is limestone, silica sand, and fluorspar. These samples were subjected to several comparative tests used to characterise cements including examination under x-ray diffractometer, scanning electron microscopy and tests for setting time and compressive strength. Under similar laboratory conditions, it was possible to prove that fluoride cement hardens more rapidly than ordinary Portland cement. Also observed during the experimental work is that fluoride cement develops higher compressive strengths than ordinary Portland cement. The hardening and setting times are significantly different between the two cements. Also the nature of the hydration products, that is the microstructural development is significantly different in the two cements. The differences brought about between the two cements are because of the presence of fluorine during the clinkering

  7. Status of barium studies in the present era of oncology: Are they a history?

    PubMed Central

    Mahajan, Abhishek; Desai, Subash; Sable, Nilesh Pandurang; Thakur, Meenakshi Haresh

    2016-01-01

    With the advent of the modern imaging technologies, the present era of oncology is seeing steady decline in requests for barium studies due to the many reasons. It is prudent to mention here, that, barium examinations cannot be made obsolete! Our aim to preserve the age old technique of barium studies not only to keep it going on but also for the betterment and appropriate management of the patient. Our goal is not to “save” barium studies simply to keep this technology alive, per se, but rather to preserve barium radiology for the quality in patient care. PMID:28144086

  8. Stabilization of arsenic- and barium-rich glass manufacturing waste

    SciTech Connect

    Fuessle, R.W.; Taylor, M.A.

    2000-03-01

    Effective solidification/stabilization (S/S) of arsenic- and barium-containing D004/D005 waste was accomplished by using a binder of cement with 40% class C fly ash and either ferrous sulfate or ferric sulfate as an additive. Addition of iron salts improves arsenic solidification/stabilization (S/S). Barium may be encapsulated within the stabilized matrix as barium sulfate. Recommended mole ratios for iron/arsenic and barium/sulfate are at least 6 and 1.2, respectively. A binder/waste ratio of 0.15 is volume efficient, but the mix design must be carefully controlled to achieve adequate S/S. In practice, the heterogeneity of waste and large-scale mix operations may preclude close control of reagent dosages, so a binder/waste ratio of 0.40 is preferable. Ferrous sulfate additive is preferable for arsenic S/S because it is effective over a wider range of mix designs and over a long-term curing period. Toxicity characteristic leaching procedure results degraded with long curing time for some mix designs with ferric sulfate additive.

  9. Heavy ion recoil spectrometry of barium strontium titanate films

    NASA Astrophysics Data System (ADS)

    Stannard, W. B.; Johnston, P. N.; Walker, S. R.; Bubb, I. F.; Scott, J. F.; Cohen, D. D.; Dytlewski, N.; Martin, J. W.

    1995-05-01

    Thin films of barium strontium titanate have been analysed using heavy ion recoil spectrometry with 77 and 98 MeV 127I ions at the new heavy ion recoil facility at ANSTO, Lucas Heights. New calibration procedures have been developed for quantitative analysis. Energy spectra for each of the elements present reveal interdiffusion that was not previously known.

  10. Synthesis of phase pure praseodymium barium copper iron oxide.

    PubMed

    Konne, Joshua L; Davis, Sean A; Glatzel, Stefan; Hall, Simon R

    2013-06-18

    The control of crystallization of praseodymium barium copper iron oxide, an intermediate temperature solid oxide fuel cell cathode material, has been demonstrated for the first time using a biotemplated sol-gel synthesis technique. The results obtained showed significant improvement in purity, synthesis time, surface area and simplicity over that previously reported.

  11. PROPOSED ORAL REFERENCE DOSE (RFD) FOR BARIUM AND COMPOUNDS

    EPA Science Inventory

    The Integrated Risk Information System (IRIS) is a database of EPA's consensus opinion of the human health effects that may result from exposure to various substances found in the environment. A Toxicological Review and IRIS Summary were prepared for barium and compounds in 1998 ...

  12. Dynamics of a barium release in the magnetospheric tail

    NASA Technical Reports Server (NTRS)

    Mende, S. B.; Swenson, G. R.; Geller, S. P.; Doolittle, J. H.; Haerendel, G.

    1989-01-01

    The late time behavior of the May 13, 1985 magnetotail barium cloud is examined. The bulk dynamics of the cloud are studied based on triangulated data and data from Fabry-Perot Doppler velocity measurements. The changes in cloud morphology in relation to the in situ measurements made by the Ion Release Module satellite are discussed.

  13. SEPARATION OF BARIUM VALUES FROM URANYL NITRATE SOLUTIONS

    DOEpatents

    Tompkins, E.R.

    1959-02-24

    The separation of radioactive barium values from a uranyl nitrate solution of neutron-irradiated uranium is described. The 10 to 20% uranyl nitrate solution is passed through a flrst column of a cation exchange resin under conditions favoring the adsorption of barium and certain other cations. The loaded resin is first washed with dilute sulfuric acid to remove a portion of the other cations, and then wash with a citric acid solution at pH of 5 to 7 to recover the barium along with a lesser amount of the other cations. The PH of the resulting eluate is adjusted to about 2.3 to 3.5 and diluted prior to passing through a smaller second column of exchange resin. The loaded resin is first washed with a citric acid solution at a pH of 3 to elute undesired cations and then with citric acid solution at a pH of 6 to eluts the barium, which is substantially free of undesired cations.

  14. Dose audit and evaluation of work practices during barium procedures using digital radiography techniques.

    PubMed

    Livingstone, Roshan S; Augustine, Philomina; Aparna, I; Raj, D Victor

    2004-10-01

    Effective dose and organ doses during barium procedures performed using digital radiography machines were estimated and the related work practices were evaluated. Measured values of dose area product (DAP) were used for the calculation of effective doses. One hundred and thirty eight patients undergoing barium procedures were included in the study. The use of additional 0.2 mm copper filter during barium procedures effectively reduced patient doses. The effective dose during barium swallow procedure varied from 0.03 mSv to 3.5 mSv; during barium meal it varied from 0.18 mSv to 2.62 mSv; and during barium enema it varied from 0.56 mSv to 4.24 mSv. Dose auditing was done on the basis of patient doses, imaging techniques and image quality. Selection of optimized exposure factors imparted lower dose to patients during barium procedures.

  15. Dental fluorosis and skeletal fluoride content as biomarkers of excess fluoride exposure in marsupials.

    PubMed

    Death, Clare; Coulson, Graeme; Kierdorf, Uwe; Kierdorf, Horst; Morris, William K; Hufschmid, Jasmin

    2015-11-15

    Particulate and gaseous fluoride emissions contaminate vegetation near fluoride-emitting industries, potentially impacting herbivorous wildlife in neighboring areas. Dental fluorosis has been associated with consumption of fluoride-contaminated foliage by juvenile livestock and wildlife in Europe and North America. For the first time, we explored the epidemiology and comparative pathology of dental fluorosis in Australian marsupials residing near an aluminium smelter. Six species (Macropus giganteus, Macropus rufogriseus, Wallabia bicolor, Phascolarctos cinereus, Trichosurus vulpecula, Pseudocheirus peregrinus) demonstrated significantly higher bone fluoride levels in the high (n=161 individuals), compared to the low (n=67 individuals), fluoride areas (p<0.001). Necropsy examinations of all six species from the high-fluoride area near the smelter revealed dental lesions considered characteristic of dental fluorosis in eutherian mammals. Within the high-fluoride area, 67% of individuals across the six species showed dental enamel lesions, compared to 3% in the low-fluoride areas. Molars that erupted before weaning were significantly less likely to display pathological lesions than those developing later, and molars in the posterior portion of the dental arcade were more severely fluorotic than anterior molars in all six species. The severity of dental lesions was positively associated with increasing bone fluoride levels in all species, revealing a potential biomarker of excess fluoride exposure.

  16. Preliminary study of the CRRES magnetospheric barium releases

    NASA Technical Reports Server (NTRS)

    Huba, J. D.; Bernhardt, P. A.; Lyon, J. G.

    1992-01-01

    Preliminary theoretical and computational analyses of the Combined Release and Radiation Effects Satellite (CRRES) magnetospheric barium releases are presented. The focus of the studies is on the evolution of the diamagnetic cavity which is formed by the barium ions as they expand outward, and on the structuring of the density and magnetic field during the expansion phase of the releases. Two sets of simulation studies are discussed. The first set is based upon a 2D ideal MHD code and provides estimates of the time and length scales associated with the formation and collapse of the diamagnetic cavity. The second set uses a nonideal MHD code; specifically, the Hall term is included. This additional term is critical to the dynamics of sub-Alfvenic plasma expansions, such as the CRRES barium releases, because it leads to instability of the expanding plasma. Detailed simulations of the G4 and G10 releases were performed. In both cases the expanding plasma rapidly structured: the G4 release structured at time t less than about 3 s and developed scale sizes of about 1-2 km, while the G10 release structured at time t less than about 22 s and developed scale sizes of about 10-15 km. It is also found that the diamagnetic cavity size is reduced from those obtained from the ideal MHD results because of the structure. On the other hand, the structuring allows the formation of plasma blobs which appear to free stream across the magnetic field; thus, the barium plasma can propagate to larger distances traverse to the magnetic field than the case where no structuring occurs. Finally, a new normal mode of the system was discovered which may be excited at the leading edge of the expanding barium plasma.

  17. 21 CFR 872.6870 - Disposable fluoride tray.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Disposable fluoride tray. 872.6870 Section 872...) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6870 Disposable fluoride tray. (a) Identification. A disposable fluoride tray is a device made of styrofoam intended to apply fluoride topically...

  18. 21 CFR 872.6870 - Disposable fluoride tray.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Disposable fluoride tray. 872.6870 Section 872...) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6870 Disposable fluoride tray. (a) Identification. A disposable fluoride tray is a device made of styrofoam intended to apply fluoride topically...

  19. 21 CFR 872.6870 - Disposable fluoride tray.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Disposable fluoride tray. 872.6870 Section 872...) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6870 Disposable fluoride tray. (a) Identification. A disposable fluoride tray is a device made of styrofoam intended to apply fluoride topically...

  20. Fluoridation and Defluoridation. Training Module 2.230.2.77.

    ERIC Educational Resources Information Center

    McMullen, L. D.

    This document is an instructional module package prepared in objective form for use by an instructor familiar with fluoridation and fluoride feeding equipment. Enclosed are objectives, an instructor guide, student handouts and transparency masters. The module considers the principles and purposes of fluoridation, methods of feeding fluoride,…

  1. Fluoride Programs in the School Setting: Preventive Dental Health.

    ERIC Educational Resources Information Center

    Rebich, Theodore, Jr.; And Others

    1982-01-01

    Two types of school-based programs that increase students' use of fluoride for preventive dental health are described. In fluoride mouthrinse programs, teachers give their students a fluoride solution once a week in a paper cup. In areas where the level of fluoride in the water supply is insufficient, the flouride tablet program is used. (JN)

  2. Physiologic conditions affect toxicity of ingested industrial fluoride.

    PubMed

    Sauerheber, Richard

    2013-01-01

    The effects of calcium ion and broad pH ranges on free fluoride ion aqueous concentrations were measured directly and computed theoretically. Solubility calculations indicate that blood fluoride concentrations that occur in lethal poisonings would decrease calcium below prevailing levels. Acute lethal poisoning and also many of the chronic effects of fluoride involve alterations in the chemical activity of calcium by the fluoride ion. Natural calcium fluoride with low solubility and toxicity from ingestion is distinct from fully soluble toxic industrial fluorides. The toxicity of fluoride is determined by environmental conditions and the positive cations present. At a pH typical of gastric juice, fluoride is largely protonated as hydrofluoric acid HF. Industrial fluoride ingested from treated water enters saliva at levels too low to affect dental caries. Blood levels during lifelong consumption can harm heart, bone, brain, and even developing teeth enamel. The widespread policy known as water fluoridation is discussed in light of these findings.

  3. Physiologic Conditions Affect Toxicity of Ingested Industrial Fluoride

    PubMed Central

    Sauerheber, Richard

    2013-01-01

    The effects of calcium ion and broad pH ranges on free fluoride ion aqueous concentrations were measured directly and computed theoretically. Solubility calculations indicate that blood fluoride concentrations that occur in lethal poisonings would decrease calcium below prevailing levels. Acute lethal poisoning and also many of the chronic effects of fluoride involve alterations in the chemical activity of calcium by the fluoride ion. Natural calcium fluoride with low solubility and toxicity from ingestion is distinct from fully soluble toxic industrial fluorides. The toxicity of fluoride is determined by environmental conditions and the positive cations present. At a pH typical of gastric juice, fluoride is largely protonated as hydrofluoric acid HF. Industrial fluoride ingested from treated water enters saliva at levels too low to affect dental caries. Blood levels during lifelong consumption can harm heart, bone, brain, and even developing teeth enamel. The widespread policy known as water fluoridation is discussed in light of these findings. PMID:23840230

  4. Fluoride Plus Functionalized β-TCP

    PubMed Central

    Karlinsey, R.L.; Pfarrer, A.M.

    2012-01-01

    With more than 50 years of clinical success, fluoride serves as the gold standard agent for preventing tooth decay. In particular, the action of fluoride facilitates saliva-driven remineralization of demineralized enamel and alters solubility beneficially. Still, tooth decay remains problematic, and one way to address it may be through the development of new mineralizing agents. Laboratory and clinical studies have demonstrated that the combination of fluoride and functionalized β-tricalcium phosphate (fTCP) produces stronger, more acid-resistant mineral relative to fluoride, native β-TCP, or fTCP alone. In contrast to other calcium-based approaches that seem to rely on high levels of calcium and phosphate to drive remineralization, fTCP is a low-dose system designed to fit within existing topical fluoride preparations. The functionalization of β-TCP with organic and/or inorganic molecules provides a barrier that prevents premature fluoride-calcium interactions and aids in mineralization when applied via common preparations and procedures. While additional clinical studies are warranted, supplementing with fTCP to enhance fluoride-based nucleation activity, with subsequent remineralization driven by dietary and salivary calcium and phosphate, appears to be a promising approach. PMID:22899679

  5. Current status of fluoride volatility method development

    SciTech Connect

    Uhlir, J.; Marecek, M.; Skarohlid, J.

    2013-07-01

    The Fluoride Volatility Method is based on a separation process, which comes out from the specific property of uranium, neptunium and plutonium to form volatile hexafluorides whereas most of fission products (mainly lanthanides) and higher transplutonium elements (americium, curium) present in irradiated fuel form nonvolatile tri-fluorides. Fluoride Volatility Method itself is based on direct fluorination of the spent fuel, but before the fluorination step, the removal of cladding material and subsequent transformation of the fuel into a powdered form with a suitable grain size have to be done. The fluorination is made with fluorine gas in a flame fluorination reactor, where the volatile fluorides (mostly UF{sub 6}) are separated from the non-volatile ones (trivalent minor actinides and majority of fission products). The subsequent operations necessary for partitioning of volatile fluorides are the condensation and evaporation of volatile fluorides, the thermal decomposition of PuF{sub 6} and the finally distillation and sorption used for the purification of uranium product. The Fluoride Volatility Method is considered to be a promising advanced pyrochemical reprocessing technology, which can mainly be used for the reprocessing of oxide spent fuels coming from future GEN IV fast reactors.

  6. 76 FR 37129 - Determination That SODIUM FLUORIDE F 18 (Sodium Fluoride F-18) Injection, 10 to 200 Millicuries...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-24

    ... HUMAN SERVICES Food and Drug Administration Determination That SODIUM FLUORIDE F 18 (Sodium Fluoride F... Drug Administration (FDA) has determined that SODIUM FLUORIDE F 18 (sodium fluoride F-18) injection, 10... effectiveness. This determination will allow FDA to approve abbreviated new drug applications (ANDAs) for...

  7. Fluoride

    MedlinePlus

    ... straight from the bottle or mixed with cereal, fruit juice, or other foods. Use a dropper or an ... mouth, chewed, or added to drinking water or fruit juice. Tablets also may be added to water for ...

  8. Fluoride Retention following the Professional Topical Application of 2% Neutral Sodium Fluoride Foam

    PubMed Central

    Song, Wenqun; Toda, Shinji; Komiyama, Eri; Komiyama, Karin; Arakawa, Yuki; He, Dawei; Arakawa, Hirohisa

    2011-01-01

    The objective of the present research was to determine the appropriate amount of fluoride to use professional topical application and the residual amounts of fluoride in the oral cavity using a 2% neutral sodium fluoride (NaF) foam with a dedicated tray. Using dentition study models, a method for determining the appropriate amount of NaF foam was investigated. In eight adult subjects, the appropriate amount of NaF foam, the concentration of fluoride in the saliva following professional topical application, and the amount of residual fluoride in the oral cavity following professional topical application was examined. The results indicated that the appropriate amount of NaF foam was approximately 0.8 g, the amount of residual fluoride in the oral cavity was approximately 25% of the amount of foam used. PMID:21754931

  9. Design Manual: Removal of Fluoride from Drinking Water ...

    EPA Pesticide Factsheets

    This document is an updated version of the Design Manual: Removal of Fluoride from Drinking Water Supplies by Activated Alumina (Rubel, 1984). The manual is an in-depth presentation of the steps required to design and operate a fluoride removal plant using activated alumina (AA), which is a reliable and cost-effective process for treating excess fluoride from drinking water supplies. Design Manual on removing fluoride from drinking water to support the fluoride MCL - manual

  10. PROCESS FOR TREATING VOLATILE METAL FLUORIDES

    DOEpatents

    Rudge, A.J.; Lowe, A.J.

    1957-10-01

    This patent relates to the purification of uranium hexafluoride, made by reacting the metal or its tetrafluoride with fluorine, from the frequently contained traces of hydrofluoric acid. According to the present process, UF/sub 6/ containing as an impurity a small amount of hydrofluoric acid, is treated to remove such impurity by contact with an anhydrous alkali metal fluoride such as sodium fluoride. In this way a non-volatile complex containing hydrofluoric acid and the alkali metal fluoride is formed, and the volatile UF /sub 6/ may then be removed by distillation.

  11. High density fluoride glass calorimeter

    NASA Astrophysics Data System (ADS)

    Xie, Q.; Scheltzbaum, J.; Akgun, U.

    2014-04-01

    The unprecedented radiation levels in current Large Hadron Collider runs, and plans to even increase the luminosity creates a need for new detector technologies to be investigated. Quartz plates to replace the plastic scintillators in current LHC calorimeters have been proposed in recent reports. Quartz based Cherenkov calorimeters can solve the radiation damage problem, however light production and transfer have proven to be challenging. This report summarizes the results from a computational study on the performance of a high-density glass calorimeter. High-density, scintillating, fluoride glass, CHG3, was used as the active material. This glass has been developed specifically for hadron collider experiments, and is known for fast response time, in addition to high light yield. Here, the details of a Geant4 model for a sampling calorimeter prototype with 20 layers, and its hadronic as well as electromagnetic performances are reported.

  12. REDUCTION OF FLUORIDE TO METAL

    DOEpatents

    Carlson, O.N.; Schmidt, F.A.; Spedding, F.H.

    1960-08-30

    A process is given for making yttrium metal by reducing yttrium fluoride with calcium plus magnesium. Calcium is added in an excess of from 10 to 20% and magnesium in a quantity to yield a magnesium--yttrium alloy containing from 12 to 25% magnesium when the reaction mass is heated in an inert atmosphere at from 900 to 1106 deg C, but preferably above the melting point of the alloy. Calcium chloride may be added so as to obtain a less viscous slag containing from 30 to 60% calcium chloride. After removal of the slag the alloy is vacuum-heated at about 1100 deg C for volatilization of the magnesium and calcium.

  13. Effects of treatment with sodium fluoride and subsequent starvation on fluoride content of earthworms

    SciTech Connect

    Walton, K.C.

    1987-01-01

    The two experiments described here originated during a long-term investigation into the occurrence and movement of pollutant fluoride in a terrestrial ecosystem. Moles (Talpa europaea) whose diet consist largely of various species of earthworm Lumbricidae, are one of the species under investigation. Bone fluoride in moles was found to be higher, on average, than in foxes or small rodents. Moles probably acquire fluoride from their earthworm diet. Earthworms do not have any readily identifiable tissue in which to store large amounts of fluoride but, for their size, they have a considerable amount of soil in their gut, up oto 20% of their dry weight. Preliminary measurements of fluoride in whole earthworms suggested that observed levels could probably be accounted for by fluoride bound in the mineral part of contained soil and released during preparatory ashing. Two experiments to investigate this situation are described; here their aims were: to expose earthworms kept in soil to different concentrations of sodium fluoride; to measure resulting fluoride in earthworms when soil was removed from their gut by starvation for varying periods of time; and to compare amounts of fluoride in whole starved earthworms with those in starved earthworms from which remaining soil had also been physically removed by dissection and washing.

  14. Daily Fluoride Intake from Iranian Green Tea: Evaluation of Various Flavorings on Fluoride Release

    PubMed Central

    Maleki, Afshin; Daraei, Hiua; Mohammadi, Elham; Zandi, Shiva; Teymouri, Pari; Mahvi, Amir Hossien; Gharibi, Fardin

    2016-01-01

    With increased awareness of the health benefits of the compounds in green tea, especially polyphenols, its consumption is rising. The main purpose of this study is to determine the effect of different additives on the released fluoride into tea liquor and also daily fluoride intake. The concentrations of fluoride, nitrate, sulfate, and chloride were measured in 15 different flavored green teas (Refah-Lahijan). The fluoride and other anion concentrations were measured by ion chromatography method. The data were analyzed with Statistical Package for the Social Sciences version 16.0. The results showed that the minimum and maximum concentrations of fluoride in the green tea infusions were 0.162 mg/L (cinnamon-flavored green tea) and 3.29 mg/L (bagged peach-flavored green tea), respectively. The mean concentration of fluoride in the green tea leaves was 52 mg/kg, and approximately 89% of the fluoride was released from the green tea leaves into the infusions after brewing. The fluoride concentrations varied significantly among the examined green teas (P < 0.05). However, the additives had no significant effect on the fluoride release into the infusions (P > 0.05). Finally, drinking of the studied green teas cannot make a significant contribution to the daily dietary intake of F for consumers. PMID:27042093

  15. Daily Fluoride Intake from Iranian Green Tea: Evaluation of Various Flavorings on Fluoride Release.

    PubMed

    Maleki, Afshin; Daraei, Hiua; Mohammadi, Elham; Zandi, Shiva; Teymouri, Pari; Mahvi, Amir Hossien; Gharibi, Fardin

    2016-01-01

    With increased awareness of the health benefits of the compounds in green tea, especially polyphenols, its consumption is rising. The main purpose of this study is to determine the effect of different additives on the released fluoride into tea liquor and also daily fluoride intake. The concentrations of fluoride, nitrate, sulfate, and chloride were measured in 15 different flavored green teas (Refah-Lahijan). The fluoride and other anion concentrations were measured by ion chromatography method. The data were analyzed with Statistical Package for the Social Sciences version 16.0. The results showed that the minimum and maximum concentrations of fluoride in the green tea infusions were 0.162 mg/L (cinnamon-flavored green tea) and 3.29 mg/L (bagged peach-flavored green tea), respectively. The mean concentration of fluoride in the green tea leaves was 52 mg/kg, and approximately 89% of the fluoride was released from the green tea leaves into the infusions after brewing. The fluoride concentrations varied significantly among the examined green teas (P < 0.05). However, the additives had no significant effect on the fluoride release into the infusions (P > 0.05). Finally, drinking of the studied green teas cannot make a significant contribution to the daily dietary intake of F for consumers.

  16. Materials corrosion in molten lithium fluoride-sodium fluoride-potassium fluoride eutectic salt

    NASA Astrophysics Data System (ADS)

    Olson, Luke Christopher

    Static corrosion studies were undertaken to determine the compatibility of several candidate high temperature materials for a heat transfer loop in a molten alkali fluoride eutectic salt, LiF-NaF-KF: 46.5-11.5-42 mol % (commonly referred to as FLiNaK), as well as a molten chloride near eutectic salt, KCl-MgCl2: 68-32 mol %. Several high temperature alloys: Hastelloy-N, Hastelloy-X, Haynes-230, Inconel-617, and Incoloy-800H, Nb-1Zr, a nearly pure Ni alloy Ni-201, and a C/SiSiC ceramic were exposed to molten FLiNaK at 850°C for 500 h in sealed graphite crucibles under an argon cover gas. Corrosion occurred predominantly from dealloying of Cr from the Cr bearing alloys, an effect that was particularly pronounced at the grain boundaries. Corrosion was noted to occur from selective attack of the Si phase in the C/SiSiC ceramic. Alloy weight-loss/area due to molten fluoride salt exposure correlated with the initial Cr-content of the alloys, and was consistent with the Cr-content measured in the salts after corrosion tests. The alloys' weight-loss/area was also found to correlate to the concentration of carbon present in the nominally 20% Cr containing alloys, due to the formation of chromium carbide phases at the grain boundaries. The corrosion mechanisms for the chloride based salt were found to be similar to those observed in FLiNaK, but the chemical attack was found to be less aggressive. Sulfamate Ni electroplating and Mo plasma spraying of Fe-Ni-Cr alloy coupons was investigated to mitigate Cr dissolution. A chemical vapor deposited pyrolytic carbon and SiC coating was also investigated to protect the C/SiSiC composites. Results indicate that Ni-plating has the potential to provide protection against alloy corrosion in molten fluoride salts. Furthermore, the presence of a chromium-oxide interlayer at the interface of the Ni-plating and alloy substrate can further improve the efficacy of the Ni-plating. The pyrolytic carbon and SiC coating on the C/SiSiC composites

  17. Design, testing, fabrication and launch support of a liquid chemical barium release payload (utilizing the liquid fluorine-barium salt/hydrazine system)

    NASA Technical Reports Server (NTRS)

    Stokes, C. S.; Smith, E. W.; Murphy, W. J.

    1972-01-01

    A payload was designed which included a cryogenic oxidizer tank, a fuel tank, and burner section. Release of 30 lb of chemicals was planned to occur in 2 seconds at the optimum oxidizer to fuel ratio. The chemicals consisted of 17 lb of liquid fluorine oxidizer and 13 lb of hydrazine-barium salt fuel mixture. The fuel mixture was 17% barium chloride, 16% barium nitrate, and 67% hydrazine, and contained 2.6 lb of available barium. Two significant problem areas were resolved during the program: explosive valve development and burner operation. The release payload was flight tested, from Wallops Island, Virginia. The release took place at an altitude of approximately 260 km. The release produced a luminous cloud which expanded very rapidly, disappearing to the human eye in about 20 seconds. Barium ion concentration slowly increased over a wide area of sky until measurements were discontinued at sunrise (about 30 minutes).

  18. Surface studies of barium and barium oxide on tungsten and its application to understanding the mechanism of operation of an impregnated tungsten cathode

    NASA Technical Reports Server (NTRS)

    Forman, R.

    1976-01-01

    Surface studies have been made of multilayer and monolayer films of barium and barium oxide on a tungsten substrate. The purpose of the investigation was to synthesize the surface conditions that exist on an activated impregnated tungsten cathode and obtain a better understanding of the mechanism of operation of such cathodes. The techniques employed in these measurements were Auger spectroscopy and work-function measurements. The results of this study show that the surface of an impregnated cathode is identical to that observed for a synthesized monolayer or partial monolayer of barium on oxidized tungsten by evaluating Auger spectra and work-function measurements. Data obtained from desorption studies of barium monolayers on a tungsten substrate in conjunction with Auger and work-function results have been interpreted to show that throughout most of its life an impreganated cathode has a partial monolayer, rather than a monolayer, of barium on its surface.

  19. Materials processing apparatus development for fluoride glass

    NASA Technical Reports Server (NTRS)

    Smith, Guy A.; Kosten, Sue; Workman, Gary L.

    1994-01-01

    Fluoride glasses have great potential for optical fiber communications due to the high transmittance when no microcrystallites occur during drawing operations. This work has developed apparatus to test the occurrence of microcrystallites during recrystallization in reduced gravity on the KC-135. The apparatus allows fluoride glass fiber, such as ZBLAN, to be melted and recrystallized during both the low and high g portions the parabolic flight.

  20. Barium titanate nanoparticles: promising multitasking vectors in nanomedicine

    NASA Astrophysics Data System (ADS)

    Graziana Genchi, Giada; Marino, Attilio; Rocca, Antonella; Mattoli, Virgilio; Ciofani, Gianni

    2016-06-01

    Ceramic materials based on perovskite-like oxides have traditionally been the object of intense interest for their applicability in electrical and electronic devices. Due to its high dielectric constant and piezoelectric features, barium titanate (BaTiO3) is probably one of the most studied compounds of this family. Recently, an increasing number of studies have been focused on the exploitation of barium titanate nanoparticles (BTNPs) in the biomedical field, owing to the high biocompatibility of BTNPs and their peculiar non-linear optical properties that have encouraged their use as nanocarriers for drug delivery and as label-free imaging probes. In this review, we summarize all the recent findings about these ‘smart’ nanoparticles, including the latest, most promising potential as nanotransducers for cell stimulation.

  1. Redox processes in highly yttrium-doped barium titanate

    NASA Astrophysics Data System (ADS)

    Belous, Anatolii; V'yunov, Oleg; Kovalenko, Leonid; Makovec, Darko

    2005-05-01

    The changes of microstructure occurring during oxidation of the reduced form of yttrium-doped barium titanate (BaYxrad Ti1-x4+Tix3+O) have been studied. Samples were sintered under reduction conditions at P=10 Pa and oxidized by annealing at high temperatures (1150 and 1350 °C) in air. Depending on yttrium concentration, the oxidation of the reduced form of the yttrium-doped BaTiO 3 caused precipitation of the phase Ba 6Ti 17O 40 or the phases Ba 6Ti 17O 40 and Y 2Ti 2O 7. The precipitates had well-defined orientational relationships with the perovskite matrix. Oxidation of the reduced form of doped barium titanate results in formation of the phase BaYxrad Ti1-x/44+(VTi⁗)O responsible for increase in the resistance of outer grain layers, which lie between grain boundaries and grain.

  2. Numerical simulation of a radially injected barium cloud

    NASA Technical Reports Server (NTRS)

    Swift, D. W.; Wescott, E. M.

    1981-01-01

    Electrostatic two-dimensional numerical simulations of a radially symmetric barium injection experiment demonstrate that ions created by solar UV irradiation are electrostatically bound to the electrons which remain tied to the field lines on which they are created. Two possible instabilities are identified, but neither of them causes the barium plasma cloud to polarize in a way that would permit the plasma to keep up with the neutrals. In a second model, the velocity of the neutrals is allowed to be a function of the azimuthal angle. Here, a portion of the cloud does polarize in a way that allows a portion of the plasma to detach and move outward at the approximate speed of the neutrals. No rapid detachment is found when only the density of the neutrals is given an azimuthal asymmetry.

  3. Observations and theory of the AMPTE magnetotail barium releases

    NASA Technical Reports Server (NTRS)

    Bernhardt, P. A.; Roussel-Dupre, R. A.; Pongratz, M. B.; Haerendel, G.; Valenzuela, A.

    1987-01-01

    The barium releases in the magnetotail during the Active Magnetospheric Particle Tracer Explorers (AMPTE) operation were monitored by ground-based imagers and by instruments on the Ion Release Module. After each release, the data show the formation of a structured diamagnetic cavity. The cavity grows until the dynamic pressure of the expanding ions balances the magnetic pressure on its surface. The magnetic field inside the cavity is zero. The barium ions collect on the surface of the cavity, producing a shell. Plasma irregularities form along magnetic field lines draped over the surface of the cavity. The scale size of the irregularities is nearly equal to the thickness of the shell. The evolution and structuring of the diamagnetic cavity are modeled using magnetohydrodynamics theory.

  4. The Skylab barium plasma injection experiments. I - Convection observations

    NASA Technical Reports Server (NTRS)

    Wescott, E. M.; Stenbaek-Nielsen, H. C.; Davis, T. N.; Peek, H. M.

    1976-01-01

    Two barium-plasma injection experiments were carried out during magnetically active periods in conjunction with the Skylab 3 mission. The high-explosive shaped charges were launched near dawn on November 27 and December 4, 1973, UT. In both cases, the AE index was near 400 gammas, and extensive pulsating auroras covered the sky. The first experiment, Skylab Alpha, occurred in the waning phase of a 1000-gamma substorm, and the second, Skylab Beta, occurred in the expansive phase of an 800-gamma substorm. In both, the convection was generally magnetically eastward, with 100-km-level electric fields near 40 mV/m. However, in the Alpha experiment the observed orientation of the barium flux tube fit theoretical field lines having no parallel current, but the Beta flux-tube orientation indicated a substantial upward parallel sheet current.

  5. Study of the photovoltaic effect in thin film barium titanate

    NASA Technical Reports Server (NTRS)

    Grannemann, W. W.; Dharmadhikari, V. S.

    1982-01-01

    Ferroelectric films of barium titanate were synthesized on silicon and quartz substrates, and the photoelectric effect in the structure consisting of metal deposited ferroelectric barium titanate film silicon was studied. A photovoltage with polarity that depends on the direction of the remanent polarization was observed. The deposition of BaTiO3 on silicon and fused quartz substrates was accomplished by an rf sputtering technique. A series of experiments to study the growth of ferroelectric BaTiO3 films on single crystal silicon and fused quartz substrates were conducted. The ferroelectric character in these films was found on the basis of evidence from the polarization electric field hysteresis loops, capacitance voltage and capacitance temperature techniques and from X-ray diffraction studies.

  6. NASA/Max Planck Institute Barium Ion Cloud Project.

    NASA Technical Reports Server (NTRS)

    Brence, W. A.; Carr, R. E.; Gerlach, J. C.; Neuss, H.

    1973-01-01

    NASA and the Max Planck Institute for Extraterrestrial Physics (MPE), Munich, Germany, conducted a cooperative experiment involving the release and study of a barium cloud at 31,500 km altitude near the equatorial plane. The release was made near local magnetic midnight on Sept. 21, 1971. The MPE-built spacecraft contained a canister of 16 kg of Ba CuO mixture, a two-axis magnetometer, and other payload instrumentation. The objectives of the experiment were to investigate the interaction of the ionized barium cloud with the ambient medium and to deduce the properties of electric fields in the proximity of the release. An overview of the project is given to briefly summarize the organization, responsibilities, objectives, instrumentation, and operational aspects of the project.

  7. Dielectric function for doped graphene layer with barium titanate

    NASA Astrophysics Data System (ADS)

    Martinez Ramos, Manuel; Garces Garcia, Eric; Magana, Fernado; Vazquez Fonseca, Gerardo Jorge

    2015-03-01

    The aim of our study is to calculate the dielectric function for a system formed with a graphene layer doped with barium titanate. Density functional theory, within the local density approximation, plane-waves and pseudopotentials scheme as implemented in Quantum Espresso suite of programs was used. We considered 128 carbon atoms with a barium titanate cluster of 11 molecules as unit cell with periodic conditions. The geometry optimization is achieved. Optimization of structural configuration is performed by relaxation of all atomic positions to minimize their total energies. Band structure, density of states and linear optical response (the imaginary part of dielectric tensor) were calculated. We thank Dirección General de Asuntos del Personal Académico de la Universidad Nacional Autónoma de México, partial financial support by Grant IN-106514 and we also thank Miztli Super-Computing center the technical assistance.

  8. Drinking water quality and fluoride concentration.

    PubMed

    Frazão, Paulo; Peres, Marco A; Cury, Jaime A

    2011-10-01

    This paper aimed to analyze the fluoride concentration in drinking water, taking into account the balance between the benefits and risks to health, in order to produce scientific backing for the updating of the Brazilian legislation. Systematic reviews studies, official documents and meteorological data were examined. The temperatures in Brazilian state capitals indicate that fluoride levels should be between 0.6 and 0.9 mg F/l in order to prevent dental caries. Natural fluoride concentration of 1.5 mg F/l is tolerated for consumption in Brazil if there is no technology with an acceptable cost-benefit ratio for adjusting/removing the excess. Daily intake of water with a fluoride concentration > 0.9 mg F/l presents a risk to the dentition among children under the age of eight years, and consumers should be explicitly informed of this risk. In view of the expansion of the Brazilian water fluoridation program to regions with a typically tropical climate, Ordinance 635/75 relating to fluoride added to the public water supply should be revised.

  9. Topical laser application enhances enamel fluoride uptake and tribological properties.

    PubMed

    Jeng, Y-R; Lin, T-T; Huang, J-S; Peng, S-R; Shieh, D-B

    2013-07-01

    Topical fluoride treatment prevents dental caries. However, the resulting calcium-fluoride-like deposits are soft and have poor wear resistance; therefore, frequent treatment is required. Lasers quickly heat surfaces and can be made portable and suitable for oral remedies. We examined the morphology, nanohardness, elastic modulus, nanowear, and fluoride uptake of fluoride-treated enamel followed by CO2 laser irradiation for 5 and 10 sec, respectively. We found that laser treatments significantly increased the mechanical properties of the calcium-fluoride-like deposits. The wear resistance of the calcium-fluoride-like deposits improved about 34% after laser irradiation for 5 sec and about 40% following irradiation for 10 sec. We also found that laser treatments increased fluoride uptake by at least 23%. Overall, laser treatment significantly improved fluoride incorporation into dental tissue and the wear resistance of the protective calcium-fluoride layer.

  10. Synthesis and characterization of barium ferrite–silica nanocomposites

    SciTech Connect

    Aguilar-González, M.A.; Mendoza-Suárez, G.; Padmasree, K.P.

    2013-10-15

    In this work, we prepared barium ferrite-silica (BaM-SiO{sub 2}) nanocomposites of different molar ratios by high-energy ball milling, followed by heat-treatment at different temperatures. The microstructure, morphology and magnetic properties were characterized for different synthesis conditions by using X-ray diffraction (XRD), scanning electron microscopy (SEM) and vibrating sample magnetometry (VSM). The results indicate that 15 h of milling was enough to avoid the generation of hematite phase and to get a good dispersion of barium ferrite particles in the ceramic matrix. For milling periods beyond 15 h and heat treatment above 900 °C, the XRD patterns showed the presence of hematite phase caused by the decomposition of BaM. The agglomerate size observed through SEM analysis was around 150 nm with a good BaM dispersion into the SiO{sub 2} matrix. The highest saturation magnetization (Ms) value obtained was 43 emu/g and the corresponding coercivity (Hc) value of 3.4 kOe for the composition 60BaM-40SiO{sub 2} milled for 15 h and heat treated at 900 °C. This coercivity value is acceptable for the application in magnetic recording media. Highlights: • Barium ferrite–silica nanocomposites were prepared by high energy ball milling. • Optimal processing time is 15 h milling and heat treatment at 900 °C. • This is enough to avoid the generation of hematite phase. • Obtain good dispersion of barium ferrite particles in the ceramic matrix • Above this processing time shows the presence of increased amount of hematite.

  11. Barium borohydride chlorides: synthesis, crystal structures and thermal properties.

    PubMed

    Grube, Elisabeth; Olesen, Cathrine H; Ravnsbæk, Dorthe B; Jensen, Torben R

    2016-05-10

    Here we report the synthesis, mechanism of formation, characterization and thermal decomposition of new barium borohydride chlorides prepared by mechanochemistry and thermal treatment of MBH4-BaCl2, M = Li, Na or K in ratios 1 : 1 and 1 : 2. Initially, orthorhombic barium chloride, o-BaCl2 transforms into o-Ba(BH4)xCl2-x, x ∼ 0.15. Excess LiBH4 leads to continued anion substitution and a phase transformation into hexagonal barium borohydride chloride h-Ba(BH4)xCl2-x, which accommodates higher amounts of borohydride, possibly x ∼ 0.85 and resembles h-BaCl2. Thus, two solid solutions are in equilibrium during mechano-chemical treatment of LiBH4-BaCl2 (1 : 1) whereas LiBH4-BaCl2 (2 : 1) converts to h-Ba(BH4)0.85Cl1.15. Upon thermal treatment at T > ∼200 °C, h-Ba(BH4)0.85Cl1.15 transforms into another orthorhombic barium borohydride chloride compound, o-Ba(BH4)0.85Cl1.15, which is structurally similar to o-BaBr2. The samples with M = Na and K have lower reactivity and form o-Ba(BH4)xCl2-x, x ∼ 0.1 and a solid solution of sodium chloride dissolved in solid sodium borohydride, Na(BH4)1-xClx, x = 0.07. The new compounds and reaction mechanisms are investigated by in situ synchrotron radiation powder X-ray diffraction (SR-PXD), Fourier transform infrared spectroscopy (FT-IR) and simultaneous thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), mass spectroscopy (MS) and temperature programmed photographic analysis (TPPA).

  12. Complex Impedance Studies of Optically Excited Strontium Barium Niobate

    DTIC Science & Technology

    2007-11-02

    has a tetragonal tungsten - bronze structure. The unit cell for this structure, illustrated below in Fig. 2.1, consists of ten oxygen octahedra joined...4 Kittel, pp. 373-374. 5 P. B. Jamieson, et al, “Ferroelectric Tungsten Bronze -Type Crystal Structures. I. Barium Strontium Niobate...Oxford, 1987). 2. C. Kittel, Introduction to Solid State Physics, (Wiley, New York, 1986). 3. P. B. Jamieson, et al, “Ferroelectric Tungsten

  13. Barium isotopes in chondritic meteorites: implications for planetary reservoir models.

    PubMed

    Ranen, Michael C; Jacobsen, Stein B

    2006-11-03

    High-precision barium isotope measurements yielded differences of up to 25 parts per million in the 137Ba/136Ba ratio and 60 parts per million in the 138Ba/136Ba ratio between chondrites and Earth. These differences probably arose from incomplete mixing of nucleosynthetic material in the solar nebula. Chondritic meteorites have a slight excess of supernova-derived material as compared to Earth, demonstrating that the solar nebula was not perfectly homogenized upon formation.

  14. Acute barium intoxication following ingestion of soap water solution.

    PubMed

    Joshi, Nandita; Sharma, Chhavi Sarabpreert; Sai; Sharma, Jai Prakash

    2012-10-01

    We present a rare case in which a young girl ingested a solution of a hair-removing soap. The ingestion resulted in profound hypokalemia and severe acidosis leading to flaccid paralysis, respiratory arrest and ventricular arrhythmias. Ultimately the patient made complete recovery. The soapwas found to contain barium sulfide. The degree of paralysis and acidosis appeared to be directly related to serum potassium levels.

  15. Acute barium intoxication following ingestion of soap water solution

    PubMed Central

    Joshi, Nandita; Sharma, Chhavi Sarabpreert; Sai; Sharma, Jai Prakash

    2012-01-01

    We present a rare case in which a young girl ingested a solution of a hair-removing soap. The ingestion resulted in profound hypokalemia and severe acidosis leading to flaccid paralysis, respiratory arrest and ventricular arrhythmias. Ultimately the patient made complete recovery. The soapwas found to contain barium sulfide. The degree of paralysis and acidosis appeared to be directly related to serum potassium levels. PMID:23559738

  16. Barium hexaferrite based on the waste products from electroplating processes

    SciTech Connect

    Vlasov, A.S.; Stepanchikova, I.G.; Makarov, S.V.; Zaitsev, V.A.; Danilov, A.S.

    1987-11-01

    The authors assess the possibility of simultaneously treating and using waste electroplating slurries containing large amounts of iron hydroxides for obtaining barium hexaferrite ceramics. Differential thermal analysis was employed to determine the processing and recovery parameters and the resulting hexaferrites were tested, mechanically and by x-ray diffraction, for their mechanical and magnetic properties as well as for their phase composition and structure. The consequences of the process on pollution abatement are also evaluated.

  17. Texture and Microstructural Development in Gelcast Barium Hexaferrite

    SciTech Connect

    Hovis, David B.; Faber, Katherine T.; Kenik, Edward A

    2008-01-01

    The development of texture in barium hexaferrite by templated grain growth was studied as a function of the Fe2O3/BaCO3 ratio, B2O3 additions in the starting materials, and sintering temperature. A magnetic field was used to orient the template particles during the gelcasting process. Excess BaCO3 resulted in abnormal grain growth and maximized texture, while B2O3 additions promoted coarsening, but no abnormal grain growth.

  18. The effective use of fluorides in public health.

    PubMed Central

    Jones, Sheila; Burt, Brian A.; Petersen, Poul Erik; Lennon, Michael A.

    2005-01-01

    Dental caries remain a public health problem for many developing countries and for underprivileged populations in developed countries. This paper outlines the historical development of public health approaches to the use of fluoride and comments on their effectiveness. Early research and development was concerned with waterborne fluorides, both naturally occurring and added, and their effects on the prevalence and incidence of dental caries and dental fluorosis. In the latter half of the 20th century, the focus of research was on fluoride toothpastes and mouth rinses. More recently, systematic reviews summarizing these extensive databases have indicated that water fluoridation and fluoride toothpastes both substantially reduce the prevalence and incidence of dental caries. We present four case studies that illustrate the use of fluoride in modern public health practice, focusing on: recent water fluoridation schemes in California, USA; salt fluoridation in Jamaica; milk fluoridation in Chile; and the development of "affordable" fluoride toothpastes in Indonesia. Common themes are the concern to reduce demands for compliance with fluoride regimes that rely upon action by individuals and their families, and the issue of cost. We recommend that a community should use no more than one systemic fluoride (i.e. water or salt or milk fluoridation) combined with the use of fluoride toothpastes, and that the prevalence of dental fluorosis should be monitored in order to detect increases in or higher-than-acceptable levels. PMID:16211158

  19. Life Model of Hollow Cathodes Using a Barium Calcium Aluminate Impregnated Tungsten Emitter

    NASA Technical Reports Server (NTRS)

    Kovaleski, S. D.; Burke, Tom (Technical Monitor)

    2001-01-01

    Hollow cathodes with barium calcium aluminate impregnated tungsten emitters for thermionic emission are widely used in electric propulsion. These high current, low power cathodes are employed in ion thrusters, Hall thrusters, and on the International Space Station in plasma contactors. The requirements on hollow cathode life are growing more stringent with the increasing use of electric propulsion technology. The life limiting mechanism that determines the entitlement lifetime of a barium impregnated thermionic emission cathode is the evolution and transport of barium away from the emitter surface. A model is being developed to study the process of barium transport and loss from the emitter insert in hollow cathodes. The model accounts for the production of barium through analysis of the relevant impregnate chemistry. Transport of barium through the approximately static gas is also being treated. Finally, the effect of temperature gradients within the cathode are considered.

  20. Toward remote ion-ion entanglement with barium

    NASA Astrophysics Data System (ADS)

    Noel, Thomas W.; Auchter, Carolyn; Chou, Chen-Kuan; Blinov, Boris B.

    2015-03-01

    We present work toward remote entanglement of barium ions in traps separated by a few meters. A new version of an ion trap specialized for remote entanglement is introduced. The new trap allows for highly efficient collection of ion fluorescence while simultaneously minimizing ion micromotion and aligning the trap position precisely to the focus of an in-vacuum parabolic mirror by using a set of bias electrodes and a piezoelectric micro-positioning system. The success rate of the remote entanglement procedure depends strongly on the efficiency with which ion fluorescence can be coupled into an optical fiber. Characterization of our system in terms of ion fluorescence collection and fiber coupling efficiency is presented. Results demonstrating entanglement between a single barium ion and single spontaneously emitted photons are shown. The entanglement fidelity of the ion-photon state is measured to be 0.84(1) and a CHSH Bell signal of 2.303(36) finds violation of the CHSH version of the Bell inequality by over eight standard deviations. Barium's relatively long wavelength transitions make it an ideal candidate for our longer term goal of remote entanglement of ions separated by a kilometer or more. Such long distance remote entanglement should allow for a loophole-free verification of the violation of the Bell inequality.

  1. Barium as a potential indicator of phosphorus in agricultural runoff.

    PubMed

    Ahlgren, Joakim; Djodjic, Faruk; Wallin, Mats

    2012-01-01

    In many catchments, anthropogenic input of contaminants, and in particular phosphorus (P), into surface water is a mixture of agricultural and sewage runoff. Knowledge about the relative contribution from each of these sources is vital for mitigation of major environmental problems such as eutrophication. In this study, we investigated whether the distribution of trace elements in surface waters can be used to trace the contamination source. Water from three groups of streams was investigated: streams influenced only by agricultural runoff, streams influenced mainly by sewage runoff, and reference streams. Samples were collected at different flow regimes and times of year and analyzed for 62 elements using ICP-MS. Our results show that there are significant differences between the anthropogenic sources affecting the streams in terms of total element composition and individual elements, indicating that the method has the potential to trace anthropogenic impact on surface waters. The elements that show significant differences between sources are strontium (p < 0.001), calcium (p < 0.004), potassium (p < 0.001), magnesium (p < 0.001), boron (p < 0.001), rhodium (p = 0.001), and barium (p < 0.001). According to this study, barium shows the greatest potential as a tracer for an individual source of anthropogenic input to surface waters. We observed a strong relationship between barium and total P in the investigated samples (R(2) = 0.78), which could potentially be used to apportion anthropogenic sources of P and thereby facilitate targeting of mitigation practices.

  2. The Tordo 1 polar cusp barium plasma injection experiment

    NASA Technical Reports Server (NTRS)

    Wescott, E. M.; Stenbaek-Nielsen, H. C.; Davis, T. N.; Jeffries, R. A.; Roach, W. H.

    1978-01-01

    In January 1975, two barium plasma injection experiments were carried out with rockets launched into the upper atmosphere where field lines from the dayside cusp region intersect the ionosphere. The Tordo 1 experiment took place near the beginning of a worldwide magnetic storm. It became a polar cap experiment almost immediately as convection perpendicular to the magnetic field moved the fluorescent plasma jet away from the cusp across the polar cap in an antisunward direction. Convection across the polar cap with an average velocity of more than 1 km/s was observed for nearly 40 min until the barium flux tubes encountered large electron fields associated with a poleward bulge of the auroral oval near Greenland. Prior to the encounter with the aurora near Greenland there is evidence of upward acceleration of the barium ions while they were in the polar cap. The three-dimensional observations of the plasma orientation and motion give an insight into convection from the cusp region across the polar cap, the orientation of the polar cap magnetic field lines out to several earth radii, the causes of polar cap magnetic perturbations, and parallel acceleration processes.

  3. Barium thiolates and selenolates: syntheses and structural principles.

    PubMed

    Ruhlandt-Senge, K; Englich, U

    2000-11-17

    The synthesis and structural characterization of a family of barium thiolates and selenolates is described. The thiolates were synthesized by metallation of thiols, the selenolates by reductive insertion of the metal into the selenium-selenium bond of diorganodiselenides. Both reaction sequences were carried out by using barium metal dissolved in ammonia; this afforded barium thiolates and selenolates in good yield and purity. The structural principles displayed in the target compounds span a wide range of solid-state formulations, including monomeric and dimeric species, and separated ion triples, namely [Ba(thf)4(SMes*)2] (1; Mes* = 2,4,6-tBU3C6H2), [Ba(thf)4(SeMes*)2] (2), [Ba([18]crown-6)(hmpa)2][(SeMes*)2] (3), the dimeric [(Ba(py)3(thf)(SeTrip)2)2] (4; py = pyridine, Trip = 2,4.6-iPr3C6H2), and [Ba([18]crown-6)(SeTrip)2] (5). The full range of association modes is completed by [Ba([18]crown-6)(hmpa)SMes*][SMes*] (6) communicated earlier by this group. In the solid state, this compound displays an intermediate ion coordination mode: one anion is bound to the metal, while the second one is unassociated. Together these compounds provide structural information about all three different association modes for alkaline earth metal derivatives. This collection of structural data allows important conclusions about the influence of solvation and ligation on structural trends.

  4. Atomic force microscopy studies of twins in yttrium-doped barium titanate

    NASA Astrophysics Data System (ADS)

    Gheno, Simoni Maria; Hasegawa, Haroldo Lhou; Filho, Pedro Iris Paulin

    2006-11-01

    Barium titanate is the main constituent of PTC materials and their electric properties are sensitive to microstructure and defects, in atomic scale, that are significantly affected by processing parameters. The microstructure of barium titanate doped with yttrium was investigated using topographic images obtained by AFM in contact mode. The AFM images of barium titanate doped with yttrium showed the effect of large grains with double twins at different (1 1 1) planes.

  5. Fluoride - is it capable of fighting old and new dental diseases? An overview of existing fluoride compounds and their clinical applications.

    PubMed

    Brambilla, E

    2001-01-01

    Since researchers first became aware of the anticaries action of fluoride, they have been investigating the effect of this preventive agent in inhibiting or arresting caries development. Many forms of systemic or topical fluoride have been studied and tested for clinical application. Water, salt, milk fluoridation and the use of fluoride supplements were introduced for systemic fluoridation mainly using sodium fluoride. Solutions, gels, toothpastes and rinses of sodium fluoride, stannous fluoride, amine fluorides, acidulated phosphate fluoride and monofluorophosphate were used for topical fluoridation. More recently nonaqueous fluoride varnishes in an alcoholic solution of natural resins and difluorosilane agents in a polyurethane matrix were introduced. Although all of these fluoridation methods have a caries-preventive action, these benefits and the ease of application is variable. As fluoride is a key component of oral health promotion a coordinated approach on a community and individual basis seems to be needed to maximize the cost-benefit ratio of prevention.

  6. Radiation losses in microwave Ku region by conducting pyrrole/barium titanate and barium hexaferrite based nanocomposites

    NASA Astrophysics Data System (ADS)

    Kaur, Talwinder; Kumar, Sachin; Narang, S. B.; Srivastava, A. K.

    2016-12-01

    Nanocomposites of substituted barium hexaferrite and barium titanate embedded in a polymer were synthesized via emulsion polymerization. The study was performed by using X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy, electron spin resonance spectroscopy, a vibrating sample magnetometer and a vector network analyzer. It is found that maximum radiation loss occur at 16.09 GHz (-14.23 dB) frequency owing to the combined effect of conducting polymer, suitable dielectric and magnetic material. This suggests that prepared material is suitable for radiation losses. Micro structural study reveals the presence of all the phases of the compounds comprises composite. Benzene ring absorption band (at 1183 cm-1) in FT-IR spectra illustrates the presence of polymer. Surface morphology reveals the presence of array of particles encapsulated by the polymer.

  7. Electric field tunable 60 GHz ferromagnetic resonance response in barium ferrite-barium strontium titanate multiferroic heterostructures

    NASA Astrophysics Data System (ADS)

    Song, Young-Yeal; Das, Jaydip; Krivosik, Pavol; Mo, Nan; Patton, Carl E.

    2009-05-01

    A magnetic-ferroelectric film heterostructure with a large electric field tuning of the ferromagnetic resonance (FMR) mode was fabricated. Pulse laser deposited 30 nm thick Pt electrodes and 3 μm thick barium strontium titanate films on Nb-doped strontium titanate substrates were capped with an unbonded 200 μm thick single crystal in-plane c-axis barium hexaferrite slab. The structure gives a 60 GHz FMR frequency shift of 16 MHz at a bias of 29 V, for an average response of 0.55 MHz/V. The maximum incremental tuning response at 29 V was 1.3 MHz/V. This is a hundredfold improvement over previous results.

  8. Hydrogen fluoride and deuterium fluoride lasers. Citations from the International Aerospace Abstracts data base

    NASA Technical Reports Server (NTRS)

    Mauk, S. C.

    1980-01-01

    Research cited from the international literature adresses various aspects of hydrogen fluoride and deuterium fluoride lasers. Topics covered include flows, laser outputs, molecular relaxation, molecular rotation, energy conversion efficiency, reaction kinetics, and laser materials. Continous wave and pulsed laser are considered. This updated bibliography contains 283 citations, 53 of which are new additions to the previous edition.

  9. Fluoride release and recharge abilities of contemporary fluoride-containing restorative materials and dental adhesives.

    PubMed

    Dionysopoulos, Dimitrios; Koliniotou-Koumpia, Eugenia; Helvatzoglou-Antoniades, Maria; Kotsanos, Nikolaos

    2013-01-01

    The aim of this study was to evaluate the fluoride release of five fluoride-releasing restorative materials and three dental adhesives, before and after NaF solution treatment. Five restorative materials (Fuji IX GP, GC Corp.; Ketac N100, 3M ESPE; Dyract Extra, Dentsply; Beautifil II, Shofu Inc.; Wave, SDI) and three dental adhesives (Stae, SDI; Fluorobond II - Shofu Inc.; Prime & Bond NT, Dentsply) were investigated before and after NaF solution treatment. A fluoride ion-selective electrode was to measure fluoride concentrations. During the 86-day period before NaF solution treatment, Fuji IX GP released the highest amount of fluoride among the restorative materials while Prime & Bond NT was the highest among the dental adhesives. After NaF solution treatment, Fuji IX GP again ranked the highest in fluoride release among the restorative materials while Fluorobond II ranked the highest among dental adhesives. It was concluded that the compositions and setting mechanisms of fluoride-containing dental materials influenced their fluoride release and recharge abilities.

  10. Molecular structures of (3-aminopropyl)trialkoxysilane on hydroxylated barium titanate nanoparticle surfaces induced by different solvents and their effect on electrical properties of barium titanate based polymer nanocomposites

    NASA Astrophysics Data System (ADS)

    Fan, Yanyan; Wang, Guanyao; Huang, Xingyi; Bu, Jing; Sun, Xiaojin; Jiang, Pingkai

    2016-02-01

    Surface modification of nanoparticles by grafting silane coupling agents has proven to be a significant approach to improve the interfacial compatibility between inorganic filler and polymer matrix. However, the impact of grafted silane molecular structure after the nanoparticle surface modification, induced by the utilized solvents and the silane alkoxy groups, on the electrical properties of the corresponding nanocomposites, has been seldom investigated. Herein, the silanization on the surface of hydroxylated barium titanate (BT-OH) nanoparticles was introduced by using two kinds of trialkoxysilane, 3-aminopropyltriethoxysilane (AMEO) and 3-aminopropyltrimethoxysilane (AMMO), with different solvents (toluene and ethanol), respectively. Solid-state 13C, 29Si nuclear magnetic resonance (NMR) spectroscopy and high-resolution X-ray photoelectron spectroscopy (XPS) were employed to validate the structure differences of alkoxysilane attachment to the nanoparticles. The effect of alkoxysilane structure attached to the nanoparticle surface on the dielectric properties of the BT based poly(vinylidene fluoride) (PVDF) nanocomposites were investigated. The results reveal that the solvents used for BT nanoparticle surface modification exhibit a significant effect on the breakdown strength of the nanocomposites. Nevertheless, the alkoxy groups of silane show a marginal influence on the dielectric properties of the nanocomposites. These research results provide important insights into the fabrication of advanced polymer nanocomposites for dielectric applications.

  11. Widespread genetic switches and toxicity resistance proteins for fluoride.

    PubMed

    Baker, Jenny L; Sudarsan, Narasimhan; Weinberg, Zasha; Roth, Adam; Stockbridge, Randy B; Breaker, Ronald R

    2012-01-13

    Most riboswitches are metabolite-binding RNA structures located in bacterial messenger RNAs where they control gene expression. We have discovered a riboswitch class in many bacterial and archaeal species whose members are selectively triggered by fluoride but reject other small anions, including chloride. These fluoride riboswitches activate expression of genes that encode putative fluoride transporters, enzymes that are known to be inhibited by fluoride, and additional proteins of unknown function. Our findings indicate that most organisms are naturally exposed to toxic levels of fluoride and that many species use fluoride-sensing RNAs to control the expression of proteins that alleviate the deleterious effects of this anion.

  12. A comparative assessment of fluoride concentration available in saliva using daily prescribed topical fluoride agents

    PubMed Central

    Talwar, Manjit; Tewari, Amrit; Chawla, H. S.; Sachdev, Vinod

    2016-01-01

    Objective: To assess the availability of fluoride concentration in saliva following the use of fluoride mouthrinse and dentifrice. Materials and Methods: The experiment was carried out in 7–15 year-old school children of Chandigarh (n = 90). The children were nonfluoride users. Baseline saliva samples were collected. The subjects were exposed to two test agents, i.e., fluoride mouthrinse (0.05%, 225 ppm F) and dentifrice (1000 ppm F) for 7 days and on the day 8, saliva samples were collected over a 20 hrs period. Wash out period of 31/2 months was there before the subjects were exposed to the second test agent. Fluoride in saliva was estimated using fluoride ion-specific electrode. Written informed consent was taken. Statistical Analysis: Kolmogorov–Smirnov test was applied to test the normality of the variables. Mann–Whitney U-test was used to compare the fluoride concentration available in saliva at respective time intervals subsequent to use of the two test agents. Results: Fluoride concentration was elevated in saliva compared to baseline for both the test agents. Fluoride mouthrinse (0.05% sodium fluoride [NaF]) and dentifrice (1000 ppm monofluorophosphate [MFP]) showed a biphasic clearance. Peak in saliva occurred at 15 mins postuse. Night-time use resulted in higher concentration of fluoride in saliva compared to baseline. There was statistically significantly higher fluoride concentration available in saliva for the dentifrice at 5 hrs, 10 hrs, and 20 hrs postuse (P < 0.05). Conclusion: Subsequent to the use of NaF (0.05%) daily mouthrinse and MFP dentifrice (1000 ppm) the fluoride concentration in saliva remained elevated to a level of 0.12 ppm for mouthrinse and 0.14 ppm for dentifrice compared to baseline (0.03 ppm) up to 20 hrs postuse. The therapeutic window though not yet established but suggested is 0.1–1 ppm for prevention of demineralization, indicating that daily use of fluoride mouthrinse and dentifrice provides fluoride concentration in

  13. Sponge-associated bacteria mineralize arsenic and barium on intracellular vesicles

    PubMed Central

    Keren, Ray; Mayzel, Boaz; Lavy, Adi; Polishchuk, Iryna; Levy, Davide; Fakra, Sirine C.; Pokroy, Boaz; Ilan, Micha

    2017-01-01

    Arsenic and barium are ubiquitous environmental toxins that accumulate in higher trophic-level organisms. Whereas metazoans have detoxifying organs to cope with toxic metals, sponges lack organs but harbour a symbiotic microbiome performing various functions. Here we examine the potential roles of microorganisms in arsenic and barium cycles in the sponge Theonella swinhoei, known to accumulate high levels of these metals. We show that a single sponge symbiotic bacterium, Entotheonella sp., constitutes the arsenic- and barium-accumulating entity within the host. These bacteria mineralize both arsenic and barium on intracellular vesicles. Our results indicate that Entotheonella sp. may act as a detoxifying organ for its host. PMID:28233852

  14. Mechanism of Electrophilic Fluorination with Pd(IV): Fluoride Capture and Subsequent Oxidative Fluoride Transfer†, ‡

    PubMed Central

    Brandt, Jochen R.; Lee, Eunsung; Boursalian, Gregory B.

    2013-01-01

    Electrophilic fluorinating reagents derived from fluoride are desirable for the synthesis of 18F-labeled molecules for positron emission tomography (PET). Here, we study the mechanism by which a Pd(IV)-complex captures fluoride and subsequently transfers it to nucleophiles. The intermediate Pd(IV)-F is formed with high rates even at the nano- to micromolar fluoride concentrations typical for radiosyntheses with 18F due to fast formation of an outer-sphere complex between fluoride and Pd(IV). The subsequent fluorine transfer from the Pd(IV)-F complex is proposed to proceed through an unusual SET/fluoride transfer/SET mechanism. The findings detailed in this manuscript provide a theoretical foundation suitable for addressing a more general approach for electrophilic fluorination with high specific activity 18F PET imaging. PMID:24376910

  15. Effects of Systemic Fluoride and in vitro Fluoride Treatment on Enamel Crystals

    PubMed Central

    Chen, H.; Czajka-Jakubowska, A.; Spencer, N.J.; Mansfield, J.F.; Robinson, C.; Clarkson, B.H.

    2008-01-01

    Systemically administered fluoride at a concentration of 75 ppm increases the surface roughness of developing enamel crystals in rats, which may be significant in advancing our understanding of the biological mechanism of fluorosis. Thus, the aim of this study was to investigate whether the increased surface roughness may be a result of surface restructuring by the direct action of fluoride at the crystal surface. We examined the fluoride dose-dependent roughening of enamel crystal surfaces in vivo, in the rat, and whether this roughening could be mimicked by the in vitro treatment of rat enamel crystals with neutral pH fluoride solutions. Our results showed that enamel crystal surface roughness increased after treatment with increasing fluoride ion concentrations, whether applied in vitro or administered systemically. This suggests a mechanism, alongside others, for the increased surface roughness of crystals in fluorotic enamel. PMID:17062747

  16. Influence of the method of fluoride administration on toxicity and fluoride concentrations in Japanese quail

    USGS Publications Warehouse

    Fleming, W.J.; Schuler, C.A.

    1988-01-01

    Young Japanese quail (Coturnix japonica) were administered NaF for 16 d either in their diet or by esophageal intubation. Based on the total fluoride ion (Emg F-) intake over the l6-d experimental period, fluoride administered by intubation was at least six times more toxic than that fed in the diet. Dietary concentrations of 1,000 ppm F- (Emg F- for 16 d = approx. 144) produced no mortality, whereas intubated doses produced 73% or greater mortality in all groups administered 54 mg F- /kg/d or more (Emg F- for 16 d _ approx. 23 mg). GraphIc companson of the regression of log F- ppm in femurs/mg F- intake showed that fluoride levels in the femurs of quail administered fluoride by intubation were higher than in those administered fluoride in the diet.

  17. Should the drinking water of Truro, Nova Scotia, be fluoridated? Water fluoridation in the 1990s.

    PubMed

    Ismail, A I; Shoveller, J; Langille, D; MacInnis, W A; McNally, M

    1993-06-01

    An epidemiological assessment of differences in caries and fluorosis prevalences between children in Truro (< 0.1 ppm) and Kentville (fluoridated at 1.1 ppm in 1991), Nova Scotia, Canada, was completed in 1991. Out of a total of 429 children, in grades 5 and 6, in the two towns in 1991, 219 (51%) were examined. Parents answered a self-administered questionnaire investigating the sources of drinking water used by the children since birth, residence history, use of fluoride supplements, dentifrices, and other fluoride products during the first 6 yr of the life. The examination criteria differentiated between non-cavitated and cavitated carious lesions. Dental fluorosis was measured using the TSIF index. Examiner agreement was excellent. Of the children examined, 80 (36.5%) drank water (fluoridated or non-fluoridated) from municipal water systems during the first 6 yr of life. The children were assigned into five groups based upon residence history and exposure to fluoridated water during the first 6 yr of life. The percentage difference in mean DMFS scores between children in the fluoridated and non-fluoridated groups is 17% (delta DMFS1 = 0.7) when non-cavitated carious lesions are included and 39% (delta DMFS2 = 1.1) when they are excluded. The differences are not statistically significant. The significant risk factors associated with the DMFS1 and DMFS2 scores identified by a stepwise multiple regression analysis are: education level of the father, gender, and number of years of reported use of toothpaste during the first 6 yr of life. Dental fluorosis (mainly TSIF score of 1) was present in 41.5% and 69.2% of the children in the non-fluoridated and fluoridated groups, respectively.(ABSTRACT TRUNCATED AT 250 WORDS)

  18. Radiation effects in fluoride glasses

    NASA Astrophysics Data System (ADS)

    Tanimura, K.; Sibley, W. A.; Suscavage, M.; Drexhage, M.

    1985-12-01

    Radiation-induced defects in Zr-based fluoride glasses have been characterized using optical absorption and electron spin resonance (ESR) techniques. The optical absorption bands due to interstitial fluorine atoms, the F2(-), FC1(-), C12(-) centers, and Zr(3+) centers have been identified by correlating optical absorption and ESR measurements. Polarized bleaching experiments indicate that the hole-type centers, and the Zr(3+) centers have anisotropic defect configurations. X-ray excitation at 14 K generates a broad, asymmetric emission band at 337 nm (3.68 eV), which is assigned to a localized-excited state similar to that for self-trapped excitons in halide crystals. The intensity of the X-ray induced emission provides further evidence that radiolysis defect production occurs in this material. The optical tail of the radiation-induced Zr(3+) absorption affects infrared transmission. Evidence is presented that the CC14 reactive-atmosphere process introduces a significant amount of Cl(-) (about 5 percent) in the glass.

  19. New Autoinductive Cascade for the Optical Sensing of Fluoride: Application in the Detection of Phosphoryl Fluoride Nerve Agents.

    PubMed

    Sun, Xiaolong; Dahlhauser, Samuel D; Anslyn, Eric V

    2017-04-05

    A new autoinductive cascade employing benzoyl fluoride as a latent source of fluoride is reported for signal amplification and optical detection of fluoride. The autoinduction leads to a maximum 4-fold signal enhancement for each fluoride generated, as well as a self-propagating cycle that generates three fluorophores for each single fluoride released. A two-step integrated protocol creates a more rapid autoinductive cascade than previously reported, as well as a highly sensitive diagnostic assay for the ultratrace quantitation of a phosphoryl fluoride nerve agent surrogate.

  20. The Northland fluoridation advocacy programme: an evaluation.

    PubMed

    Gowda, Sunitha; Thomas, David R

    2008-12-01

    On 20 July 2006, the Far North District Council resolved to fluoridate Kaitaia and Kaikohe. This was the first such initiative by any Territorial Local Authority (TLA) in New Zealand for 23 years, and resulted from a fluoridation advocacy programme. This paper describes the programme implementation, assesses its consistency with the principles of the Treaty of Waitangi, and critically examines the collaboration between the fluoride advocate and the key stakeholders. Process evaluation identified three main categories of programme implementation: policy advocacy, community action projects, and media advocacy. The collaboration of iwi, Maori health providers and the community suggests that the programme was consistent with the principles (partnership, participation and protection) ofthe Treaty ofWaitangi. Media advocacy played an important role in reflecting and engaging community views on fluoridation, and it influenced decision-making by the Far North District Council. The simultaneous, combined 'top-down and bottom-up' approach was an effective and successful strategy for fluoridation advocacy in the community. Less integrated approaches implemented on their own (such as the 'top down' approach in Whangarei and the 'bottom-up' approach in Dargaville) were not effective.

  1. Emissions of fluorides from welding processes.

    PubMed

    Szewczyńska, Małgorzata; Pągowska, Emilia; Pyrzyńska, Krystyna

    2015-11-01

    The levels of fluoride airborne particulates emitted from welding processes were investigated. They were sampled with the patented IOM Sampler, developed by J. H. Vincent and D. Mark at the Institute of Occupational Medicine (IOM), personal inhalable sampler for simultaneous collection of the inhalable and respirable size fractions. Ion chromatography with conductometric detection was used for quantitative analysis. The efficiency of fluoride extraction from the cellulose filter of the IOM sampler was examined using the standard sample of urban air particle matter SRM-1648a. The best results for extraction were obtained when water and the anionic surfactant N-Cetyl-N-N-N-trimethylammonium bromide (CTAB) were used in an ultrasonic bath. The limits of detection and quantification for the whole procedure were 8μg/L and 24μg/L, respectively. The linear range of calibration was 0.01-10mg/L, which corresponds to 0.0001-0.1mg of fluorides per m(3) in collection of a 20L air sample. The concentration of fluorides in the respirable fraction of collected air samples was in the range of 0.20-1.82mg/m(3), while the inhalable fraction contained 0.23-1.96mg/m(3) of fluorides during an eight-hour working day in the welding room.

  2. A review of the health impacts of barium from natural and anthropogenic exposure.

    PubMed

    Kravchenko, Julia; Darrah, Thomas H; Miller, Richard K; Lyerly, H Kim; Vengosh, Avner

    2014-08-01

    There is an increasing public awareness of the relatively new and expanded industrial barium uses which are potential sources of human exposure (e.g., a shale gas development that causes an increased awareness of environmental exposures to barium). However, absorption of barium in exposed humans and a full spectrum of its health effects, especially among chronically exposed to moderate and low doses of barium populations, remain unclear. We suggest a systematic literature review (from 1875 to 2014) on environmental distribution of barium, its bioaccumulation, and potential and proven health impacts (in animal models and humans) to provide the information that can be used for optimization of future experimental and epidemiological studies and developing of mitigative and preventive strategies to minimize negative health effects in exposed populations. The potential health effects of barium exposure are largely based on animal studies, while epidemiological data for humans, specifically for chronic low-level exposures, are sparse. The reported health effects include cardiovascular and kidney diseases, metabolic, neurological, and mental disorders. Age, race, dietary patterns, behavioral risks (e.g., smoking), use of medications (those that interfere with absorbed barium in human organism), and specific physiological status (e.g., pregnancy) can modify barium effects on human health. Identifying, evaluating, and predicting the health effects of chronic low-level and moderate-level barium exposures in humans is challenging: Future research is needed to develop an understanding of barium bioaccumulation in order to mitigate its potential health impacts in various exposured populations. Further, while occupationally exposed at-risk populations exist, it is also important to identify potentially vulnerable subgroups among non-occupationally exposed populations (e.g., elderly, pregnant women, children) who are at higher risk of barium exposure from drinking water and food.

  3. Removing Fluoride Ions with Continously Fed Activated Alumina.

    ERIC Educational Resources Information Center

    Wu, Yeun C.; Itemaking, Isara Cholapranee

    1979-01-01

    Discussed is the mathematical basis for determining fluoride removal during water treatment with activated alumina. The study indicates that decreasing particle size decreases the pore diffusion effect and increases fluoride removal. (AS)

  4. Gramicidin D enhances the antibacterial activity of fluoride.

    PubMed

    Nelson, James W; Zhou, Zhiyuan; Breaker, Ronald R

    2014-07-01

    Fluoride is a toxic anion found in many natural environments. One of the major bacterial defenses against fluoride is the cell envelope, which limits passage of the membrane-impermeant fluoride anion. Accordingly, compounds that enhance the permeability of bacterial membranes to fluoride should also enhance fluoride toxicity. In this study, we demonstrate that the pore-forming antibiotic gramicidin D increases fluoride uptake in Bacillus subtilis and that the antibacterial activity of this compound is potentiated by fluoride. Polymyxin B, another membrane-targeting antibiotic with a different mechanism of action, shows no such improvement. These results, along with previous findings, indicate that certain compounds that destabilize bacterial cell envelopes can enhance the toxicity of fluoride.

  5. Global water fluoridation: what is holding us back?

    PubMed

    Botchey, Sally-Ann; Ouyang, Jing; Vivekanantham, Sayinthen

    2015-01-01

    Artificial water fluoridation was introduced more than 60 y ago as a public health intervention to control dental caries. Despite wide recommendations for its use from the World Health Organization (WHO) and studies showing the benefits of water fluoridation, many countries have opted out. Currently, only 25 countries, including the United Kingdom, the United States, and Australia have schemes for artificial water fluoridation. The issues faced in efforts to promote the global uptake of water fluoridation and the factors that affect the decision to implement it are unique in both developed and developing countries and must be explored. This article addresses the benefits and challenges of artificial water fluoridation. Further, it tackles the complexities faced with uptake of water fluoridation globally, such as ethical and political controversies and the use of alternative fluoride therapies. Potential future strategies to encourage the uptake of artificial water fluoridation are also discussed.

  6. The effects of sodium fluoride and stannous fluoride on the surface roughness of intraoral magnet systems.

    PubMed

    Obatake, R M; Collard, S M; Martin, J; Ladd, G D

    1991-10-01

    Four types of intraoral magnets used for retention of overdentures and maxillofacial prostheses were exposed in vitro to SnF2 and NaF to determine the effects of fluoride rinses on surface roughness. The surface roughness (Ra) was measured, after simulated 1, 2, and 5 years' clinical exposure to fluoride (31, 62, and 155 hours). The mean change in Ra was calculated for each period of simulated exposure to fluoride for each magnet type. Two-way ANOVA was used to compare mean change in Ra between magnets within fluorides, and between fluorides within magnets. Paired t tests were used to compare mean change in Ra within fluorides within magnets. The mean change in Ra increased for all magnets after simulated 1, 2, and 5 years of exposure to SnF2 and NaF (p less than 0.03). Using the change in Ra as an indicator for corrosion, PdCo encapsulated SmCo5 magnets and their keepers demonstrated the least corrosion with either fluoride.

  7. Method for the analysis of total fluoride in fluoride-releasing dental varnishes.

    PubMed

    Carey, C M; Coleman, S S

    2014-01-01

    Today's fluoride-releasing varnishes (F-varnish) contain a wide variety of ingredients which present analytical challenges for measuring their total fluoride content. This study reports improved methods to measure fluoride content in F-varnishes. Six different commercially available F-varnishes that contain difluorosilane (0.1% F) or NaF (2.26% F) alone or in combination with calcium-phosphates were analyzed. In a vial, 1-3 drops (0.05-0.15 g) of varnish product was dispensed, dissolved in chloroform, equilibrated in TISAB and analyzed via fluoride ion-selective electrode. The average weight percentage of fluoride for all F-varnishes containing NaF ranged from 2.03 to 2.24% F, which is within 90% of the declared label concentration of 2.26% F. Analysis of the difluorosilane-containing product required an additional hydrolysis step. ANOVA found no significant difference between the 5% NaF varnishes at p < 0.05. This method for fluoride analysis yields reliable and reproducible results and can be used for a wide variety of F-varnishes. The standard uncertainty for this method is ±4%. This method may become the basis for national and international standards that ensure the F-varnish products used in clinical practice have the fluoride content declared in the product literature.

  8. Method for the Analysis of Total Fluoride in Fluoride-Releasing Dental Varnishes

    PubMed Central

    Carey, C.M.; Coleman, S.S.

    2016-01-01

    Today’s fluoride-releasing varnishes (F-varnish) contain a wide variety of ingredients which present analytical challenges for measuring their total fluoride content. This study reports improved methods to measure fluoride content in F-varnishes. Six different commercially available F-varnishes that contain difluorosilane (0.1% F) or NaF (2.26% F) alone or in combination with calcium-phosphates were analyzed. In a vial, 1–3 drops (0.05–0.15 g) of varnish product was dispensed, dissolved in chloroform, equilibrated in TISAB and analyzed via fluoride ion-selective electrode. The average weight percentage of fluoride for all F-varnishes containing NaF ranged from 2.03 to 2.24% F, which is within 90% of the declared label concentration of 2.26% F. Analysis of the difluorosilane-containing product required an additional hydrolysis step. ANOVA found no significant difference between the 5% NaF varnishes at p < 0.05. This method for fluoride analysis yields reliable and reproducible results and can be used for a wide variety of F-varnishes. The standard uncertainty for this method is ±4%. This method may become the basis for national and international standards that ensure the F-varnish products used in clinical practice have the fluoride content declared in the product literature. PMID:24557443

  9. Estimated fluoride doses from toothpastes should be based on total soluble fluoride.

    PubMed

    Oliveira, Maria José L; Martins, Carolina C; Paiva, Saul M; Tenuta, Livia M A; Cury, Jaime A

    2013-11-01

    The fluoride dose ingested by young children may be overestimated if based on levels of total fluoride (TF) rather than levels of bioavailable fluoride (total soluble fluoride-TSF) in toothpaste. The aim of the present study was to compare doses of fluoride intake based on TF and TSF. Fluoride intake in 158 Brazilian children aged three and four years was determined after tooth brushing with their usual toothpaste (either family toothpaste (n = 80) or children's toothpaste (n = 78)). The estimated dose (mg F/day/Kg of body weight) of TF or TSF ingested was calculated from the chemical analysis of the toothpastes. Although the ingested dose of TF from the family toothpastes was higher than that from the children's toothpastes (0.074 ± 0.007 and 0.039 ± 0.003 mg F/day/Kg, respectively; p < 0.05), no difference between types of toothpaste was found regarding the ingested dose based on TSF (0.039 ± 0.005 and 0.039 ± 0.005 mg F/day/Kg, respectively; p > 0.05). The fluoride dose ingested by children from toothpastes may be overestimated if based on the TF of the product. This finding suggests that the ingested dose should be calculated based on TSF. Dose of TSF ingested by children is similar whether family or children's toothpaste is used.

  10. A study of fluoride groundwater occurrence in Nathenje, Lilongwe, Malawi

    NASA Astrophysics Data System (ADS)

    Msonda, K. W. M.; Masamba, W. R. L.; Fabiano, E.

    A study was carried out to determine fluoride concentration in groundwaters of Nathenje area situated in Lilongwe District in the central region of Malawi. Water samples were collected from 176 boreholes and shallow wells during different months in 2001 and 2002. Samples were then analysed for fluoride by using a fluoride electrode and an ion selective meter. The results showed that fluoride concentrations for the rainy season varied from <0.5 to 6.98 ± 0.01 mg/l with 52.9% of the boreholes above the World Health Organisation (WHO) maximum permissible limit of 1.5 mg/l. Fluoride concentrations for dry season ranged from <0.5 to 7.02 ± 0.02 mg/l with 50.8% of boreholes above 1.5 mg/l. Fluoride concentrations for the two seasons were significantly different from each other ( p < 0.05). Fluoride data was used to produce a fluoride distribution map. From the map, it was observed that fluoride concentrations in this area followed a pattern. The central part of Nathenje had high fluoride concentration of between 2 and 7.02 mg/l and these high fluoride values seemed to extend eastwards beyond the boundary of the study area. However, the southern and western parts had <1 mg/l of fluoride. The high groundwater fluoride values seem to be associated with the weathered basement complex containing biotite that is a probable source of fluoride. The other suspected sources of fluoride in Nathenje groundwater could be due to the dissolution of hornblende, fluorite and amphibole, which are reported to occur in rocks and soils in this area. There was evidence of dental fluorosis in areas where the fluoride concentration was high.

  11. Fluoridation Status of U. S. Army Conus Installations

    DTIC Science & Technology

    1993-09-30

    optimal levels of fluoridation in order to derive maximum effectiveness and to prevent the development of dental fluorosis . ൜. DISTRIBUTION...of fluoridation in order to derive maximum effectiveness and to prevent the development of dental fluorosis . iv Background Water fluoridation has been...dental fluorosis . Although this report only informs the commanders on fluoride concentrations for a specific date, it should constitute the first step

  12. FLUORIDE: A REVIEW OF USE AND EFFECTS ON HEALTH

    PubMed Central

    Kanduti, Domen; Sterbenk, Petra; Artnik, Barbara

    2016-01-01

    Introduction: Appropriate oral health care is fundamental for any individual’s health. Dental caries is still one of the major public health problems. The most effective way of caries prevention is the use of fluoride. Aim: The aim of our research was to review the literature about fluoride toxicity and to inform physicians, dentists and public health specialists whether fluoride use is expedient and safe. Methods: Data we used in our review were systematically searched and collected from web pages and documents published from different international institutions. Results: Fluoride occurs naturally in our environment but we consume it in small amounts. Exposure can occur through dietary intake, respiration and fluoride supplements. The most important factor for fluoride presence in alimentation is fluoridated water. Methods, which led to greater fluoride exposure and lowered caries prevalence, are considered to be one of the greatest accomplishments in the 20th century`s public dental health. During pregnancy, the placenta acts as a barrier. The fluoride, therefore, crosses the placenta in low concentrations. Fluoride can be transmitted through the plasma into the mother’s milk; however, the concentration is low. The most important action of fluoride is topical, when it is present in the saliva in the appropriate concentration. The most important effect of fluoride on caries incidence is through its role in the process of remineralization and demineralization of tooth enamel. Acute toxicity can occur after ingesting one or more doses of fluoride over a short time period which then leads to poisoning. Today, poisoning is mainly due to unsupervised ingestion of products for dental and oral hygiene and over-fluoridated water. Conclusion: Even though fluoride can be toxic in extremely high concentrations, it`s topical use is safe. The European Academy of Paediatric Dentistry (EAPD) recommends a preventive topical use of fluoride supplements because of their

  13. METHOD FOR DISSOLVING LANTHANUM FLUORIDE CARRIER FOR PLUTONIUM

    DOEpatents

    Koshland, D.E. Jr.; Willard, J.E.

    1961-08-01

    A method is described for dissolving lanthanum fluoride precipitates which is applicable to lanthanum fluoride carrier precipitation processes for recovery of plutonium values from aqueous solutions. The lanthanum fluoride precipitate is contacted with an aqueous acidic solution containing dissolved zirconium in the tetravalent oxidation state. The presence of the zirconium increases the lanthanum fluoride dissolved and makes any tetravalent plutonium present more readily oxidizable to the hexavalent state. (AEC)

  14. Pharmacokinetics of fluoride in toddlers after application of 5% sodium fluoride dental varnish.

    PubMed

    Milgrom, Peter; Taves, Donald M; Kim, Amy S; Watson, Gene E; Horst, Jeremy A

    2014-09-01

    The prevalence of dental caries (tooth decay) among preschool children is increasing, driven partially by an earlier age of onset of carious lesions. The American Academy of Pediatrics recommends application of 5% sodium fluoride varnish at intervals increasing with caries risk status, as soon as teeth are present. However, the varnishes are marketed for treatment of tooth sensitivity and are regulated as medical devices rather than approved by the US Food and Drug Administration for prevention of dental caries (tooth decay). The objective of this research is to examine the safety of use in toddlers by characterizing the absorption and distribution profile of a currently marketed fluoride varnish. We measured urinary fluoride for 5 hours after application of fluoride varnish to teeth in 6 toddlers aged 12 to 15 months. Baseline levels were measured on a separate day. The urine was extracted from disposable diapers, measured by rapid diffusion, and extrapolated to plasma levels. The mean estimated plasma fluoride concentration was 13 μg/L (SD, 9 μg/L) during the baseline visit and 21 μg/L (SD, 8 μg/L) during the 5 hours after treatment. Mean estimated peak plasma fluoride after treatment was 57 μg/L (SD, 22 μg/L), and 20 μg/kg (SD, 4 μg/L) was retained on average. Retained fluoride was 253 times lower than the acute toxic dose of 5 mg/kg. Mean plasma fluoride after placement of varnish was within an SD of control levels. Occasional application of fluoride varnish following American Academy of Pediatrics guidance is safe for toddlers.

  15. Changes in plaque fluoride levels by school-based fluoride rinsing and tablet programs in Bangladesh.

    PubMed

    Hossain, Abu Nasir Mohammad Nazmul; Sampaio, Fabio Correia; von der Fehr, Frithjof Ramm; Arneberg, Pål

    2003-02-01

    The aim of this study was to evaluate the effects of school-based fluoride rinsing and tablet programs on plaque fluoride levels. A total of 42 children (8-9 years) were selected from two neighboring schools in Dhaka, Bangladesh. After caries recordings, vestibular plaque samples from the maxillary central incisors and mandibular first molars were collected and frozen on day 0 (baseline). The subjects of one school (rinsing group, n = 15) rinsed with 0.05% NaF, while those from the other school (tablet group, n = 16) used a 0.5 mg F tablet on the 5 school days during a 3-week period. The surfaces were sampled on the first and last school day every week. The fluoride and protein contents of each sample were analyzed using micro-techniques. The median plaque fluoride levels were 9.1 ppm at baseline in the rinsing group and 2.5 ppm in the tablet group (P < 0.05). This difference could in part be related to reported fluoride toothpaste usage. After 4 days on the fluoride programs, plaque fluoride levels in the rinsing group increased to 27.3, 24.5 and 14.2 ppm in the 3 consecutive weeks. The corresponding values after tablet usage were 8.0, 6.5 and 7.1 ppm, respectively. After 3 days without fluoride during the weekends, levels declined towards baseline values in both groups. Hence, the plaque fluoride levels in 8 to 9-year-old Bangladeshi children were increased by both rinsing and tablet programs, but the effect was not detectable 3 days later.

  16. Fluoride in drinking water and its removal.

    PubMed

    Meenakshi; Maheshwari, R C

    2006-09-01

    Excessive fluoride concentrations have been reported in groundwaters of more than 20 developed and developing countries including India where 19 states are facing acute fluorosis problems. Various technologies are being used to remove fluoride from water but still the problem has not been rooted out. In this paper, a broad overview of the available technologies for fluoride removal and advantages and limitations of each one have been presented based on literature survey and the experiments conducted in the laboratory with several processes. It has been concluded that the selection of treatment process should be site specific as per local needs and prevailing conditions as each technology has some limitations and no one process can serve the purpose in diverse conditions.

  17. 21 CFR 177.2510 - Polyvinylidene fluoride resins.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Polyvinylidene fluoride resins. 177.2510 Section... as Components of Articles Intended for Repeated Use § 177.2510 Polyvinylidene fluoride resins. Polyvinylidene fluoride resins may be safely used as articles or components of articles intended for repeated...

  18. 40 CFR 60.242 - Standard for fluorides.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for fluorides. 60.242 Section... Industry: Granular Triple Superphosphate Storage Facilities § 60.242 Standard for fluorides. (a) On and... atmosphere from any affected facility any gases which contain total fluorides in excess of 0.25...

  19. 40 CFR 60.232 - Standard for fluorides.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for fluorides. 60.232 Section... Industry: Triple Superphosphate Plants § 60.232 Standard for fluorides. On and after the date on which the... gases which contain total fluorides in excess of 100 g/megagram (Mg) of equivalent P2O5 feed (0.20...

  20. 40 CFR 60.212 - Standard for fluorides.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for fluorides. 60.212 Section... Industry: Superphosphoric Acid Plants § 60.212 Standard for fluorides. (a) On and after the date on which... facility any gases which contain total fluorides in excess of 5.0 g/megagram (Mg) of equivalent P2O5...

  1. 21 CFR 177.2510 - Polyvinylidene fluoride resins.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Polyvinylidene fluoride resins. 177.2510 Section... as Components of Articles Intended for Repeated Use § 177.2510 Polyvinylidene fluoride resins. Polyvinylidene fluoride resins may be safely used as articles or components of articles intended for repeated...

  2. 40 CFR 60.232 - Standard for fluorides.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for fluorides. 60.232 Section... Industry: Triple Superphosphate Plants § 60.232 Standard for fluorides. On and after the date on which the... gases which contain total fluorides in excess of 100 g/megagram (Mg) of equivalent P2O5 feed (0.20...

  3. Fluoride concentration from dental sealants: a randomized clinical trial.

    PubMed

    Campus, G; Carta, G; Cagetti, M G; Bossù, M; Sale, S; Cocco, F; Conti, G; Nardone, M; Sanna, G; Strohmenger, L; Lingström, P

    2013-07-01

    A randomized clinical trial was performed in schoolchildren (6-7 yrs) to evaluate fluoride concentration in interproximal fluid after the placement of 3 different sealants. The sample consisted of 2,776 children randomly divided: 926 in the high-viscosity Glass-ionomer Cement group (GIC group), 923 in the fluoride Resin-based group (fluoride-RB group), and 927 in the no-fluoride Resin-based group (RB group). In total, 2,640 children completed the trial. Sealants were applied following manufacturer's instructions. Interproximal fluid samples were collected at baseline and 2, 7, and 21 days after application of sealants, by insertion of a standardized paperpoint into the interproximal mesial space of the sealed tooth for 15 seconds. Fluoride concentration was evaluated by means of a fluoride ion-selective electrode. At 2 days after sealant application, fluoride concentration was significantly higher in GIC and fluoride-RB groups compared with that in the RB group (p < .01). Mean fluoride concentrations after 7 days were 2.54 (SE 0.68) ppm, 0.85 (SE 0.26) ppm, and 0.53 (SE 0.11) ppm for the three groups, respectively. After 21 days, fluoride concentration in the GIC group remained higher than that in the other two groups. High-viscosity GIC sealants increased the fluoride concentrations in interproximal fluid more than did a Resin-based sealant containing fluoride.

  4. 21 CFR 177.2510 - Polyvinylidene fluoride resins.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Polyvinylidene fluoride resins. 177.2510 Section... as Components of Articles Intended for Repeated Use § 177.2510 Polyvinylidene fluoride resins. Polyvinylidene fluoride resins may be safely used as articles or components of articles intended for repeated...

  5. 21 CFR 177.2510 - Polyvinylidene fluoride resins.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Polyvinylidene fluoride resins. 177.2510 Section... as Components of Articles Intended for Repeated Use § 177.2510 Polyvinylidene fluoride resins. Polyvinylidene fluoride resins may be safely used as articles or components of articles intended for repeated...

  6. 40 CFR 60.212 - Standard for fluorides.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for fluorides. 60.212 Section... Industry: Superphosphoric Acid Plants § 60.212 Standard for fluorides. (a) On and after the date on which... facility any gases which contain total fluorides in excess of 5.0 g/megagram (Mg) of equivalent P2O5...

  7. Health effects of fluoride pollution caused by coal burning.

    PubMed

    Ando, M; Tadano, M; Yamamoto, S; Tamura, K; Asanuma, S; Watanabe, T; Kondo, T; Sakurai, S; Ji, R; Liang, C; Chen, X; Hong, Z; Cao, S

    2001-04-23

    Recently a huge amount of fluoride in coal has been released into indoor environments by the combustion of coal and fluoride pollution seems to be increasing in some rural areas in China. Combustion of coal and coal bricks is the primary source of gaseous and aerosol fluoride and these forms of fluoride can easily enter exposed food products and the human respiratory tract. Major human fluoride exposure was caused by consumption of fluoride contaminated food, such as corn, chilies and potatoes. For each diagnostic syndrome of dental fluorosis, a log-normal distribution was observed on the logarithm of urinary fluoride concentration in students in China. Urinary fluoride content was found to be a primary health indicator of the prevalence of dental fluorosis in the community. In the fluorosis areas, osteosclerosis in skeletal fluorosis patients was observed with a high prevalence. A biochemical marker of bone resorption, urinary deoxypyridinoline content was much higher in residents in China than in residents in Japan. It was suggested that bone resorption was stimulated to a greater extent in residents in China and fluoride may stimulate both bone resorption and bone formation. Renal function especially glomerular filtration rate was very sensitive to fluoride exposure. Inorganic phosphate concentrations in urine were significantly lower in the residents in fluorosis areas in China than in non-fluorosis area in China and Japan. Since airborne fluoride from the combustion of coal pollutes extensively both the living environment and food, it is necessary to reduce fluoride pollution caused by coal burning.

  8. COMPLEX FLUORIDES OF PLUTONIUM AND AN ALKALI METAL

    DOEpatents

    Seaborg, G.T.

    1960-08-01

    A method is given for precipitating alkali metal plutonium fluorides. such as KPuF/sub 5/, KPu/sub 2/F/sub 9/, NaPuF/sub 5/, and RbPuF/sub 5/, from an aqueous plutonium(IV) solution by adding hydrogen fluoride and alkali-metal- fluoride.

  9. Resin-modified glass ionomer cements: fluoride release and uptake.

    PubMed

    Forsten, L

    1995-08-01

    The aim was to study the short- and long-term fluoride release from resin-modified glass ionomer cements (GIC). The aim was also to determine the effect of fluoride treatment of 9-month-old specimens, consistency of the mix, and pH of the environment on the fluoride release. GIC test specimens were continually exposed to running water, and the fluoride release was measured periodically by storing the specimens in 5 ml deionized water for 1 week and measuring the fluoride content of the solution. After 24 h, 1 month, 9 months, and 11 months in running water four of the six resin-modified GICs released as much as or more fluoride than the auto-curing GIC tested for comparison. Fluoride treatment after 9 months also increased the fluoride release of these four brands, as was the case with the conventional GIC. At 24 h and 1 month two of the resin-modified GICs released smaller amounts of fluoride than the other materials, and the fluoride treatment used on those had no or only a minimal effect. Thin consistency of a mix resulted in higher fluoride release for one resin-modified material than a thick mix. Low pH increased the fluoride release for all materials.

  10. Lack of effect of drinking water barium on cardiovascular risk factors.

    PubMed

    Wones, R G; Stadler, B L; Frohman, L A

    1990-04-01

    Higher cardiovascular mortality has been associated in a single epidemiological study with higher levels of barium in drinking water. The purpose of this study was to determine whether drinking water barium at levels found in some U.S. communities alters the known risk factors for cardiovascular disease. Eleven healthy men completed a 10-week dose-response protocol in which diet was controlled (600 mg cholesterol; 40% fat, 40% carbohydrate, 20% protein; sodium and potassium controlled at the subject's pre-protocol estimated intake). Other aspects of the subjects' lifestyles known to affect cardiac risk factors were controlled, and the barium content (as barium chloride) of the drinking water (1.5 L/day) was varied from 0 (first 2 weeks), to 5 ppm (next 4 weeks), to 10 ppm (last 4 weeks). Multiple blood and urine samples, morning and evening blood pressure measurements, and 48-hr electrocardiographic monitoring were performed at each dose of barium. There were no changes in morning or evening systolic or diastolic blood pressures, plasma cholesterol or lipoprotein or apolipoprotein levels, serum potassium or glucose levels, or urine catecholamine levels. There were no arrhythmias related to barium exposure detected on continuous electrocardiographic monitoring. A trend was seen toward increased total serum calcium levels with exposure to barium, which was of borderline statistical significance and of doubtful clinical significance. In summary, drinking water barium at levels of 5 and 10 ppm did not appear to affect any of the known modifiable cardiovascular risk factors.

  11. Boron Carbide as a Barium-Free Green Light Emitter and Burn Rate Modifier in Pyrotechnics

    DTIC Science & Technology

    2011-05-09

    ABSTRACT A pyrotechnic with green-light emission for both military use and civilian fireworks has been developed without the need to use barium or...material, when combined with a suitable oxidizer, may serve as an alternative in replacing barium in commercial green light emitting fireworks . In summary

  12. Replacement of SR 4990 by Barium Styphnate in the Mk 24 Actuator

    DTIC Science & Technology

    the SR-4990 in the Mk 24 Actuator. Experimental work was performed with barium styphnate , lead mononitroresorcinate, and two manufactured powders...Candidate materials were first screened using a pressure bomb. Final testing was performed in the Mk 24 Actuator design. Test results showed that of the four candidates, barium styphnate is the best material for the Actuator Mk 24.

  13. On the nature of striae in strontium barium niobate

    NASA Astrophysics Data System (ADS)

    Monchamp, R. R.; Mihalik, G. B.; Franks, L. A.

    1994-08-01

    Strontium barium niobate crystals were grown by the Czochralski technique. These crystals were 15-20 mm in diameter and 25 to 75 mm long. Two types of striae, designated as coarse and fine, were characterized. The coarse striae are optically dense and are spaced by 100 to 500 microns apart; the fine striae are optically less dense and spaced 5-50 microns apart. The origins of the striae are attributed to thermal fluctuations in the melt related to the control system and to rotation of the growing crystal in non-isothermal radial gradients. Analysis of the crystals indicated that the coarse striae may contain increased concentrations of sodium.

  14. Dielectric behavior of barium modified strontium bismuth titanate ceramic

    NASA Astrophysics Data System (ADS)

    Nayak, P.; Badapanda, T.; Anwar, S.; Panigrahi, S.

    2014-04-01

    Barium Modified Strontium Bismuth Titanate(SBT) ceramic with general formula Sr1-xBaxBi4Ti4O15 is prepared by solid state reaction route. The structural analysis of the ceramics was done by X-ray diffraction technique. The X-ray patterns show that all the compositions are of single phase with orthorhombic structure. The temperature dependent dielectric behavior shows that the transition temperature decreases with Ba content but the maximum dielectric constant increases. The decreases of the transition with increase in Ba2+ ion, may be due to the decrease of orthorhombicity by the incorporation of Ba2+ ion in SBT lattice.

  15. The barium ion jet experiments of the Porcupine project

    NASA Astrophysics Data System (ADS)

    Haerendel, G.

    1980-06-01

    The injection of a barium plasma from a sounding rocket by the shaped charge technique offers several possibilities that cannot be achieved by conventional releases. This is due to high initial velocities of the atoms of up to 14 km/sec. Most of the the applications are related to the great heights that the ions can reach, but some depend directly on the initial momentum. Typical applications are: tracing at high altitudes, modifications, and alternate Ionization processes. Project Porcupine contributions in this field are summarized.

  16. Enhanced flexoelectricity through residual ferroelectricity in barium strontium titanate

    SciTech Connect

    Garten, Lauren M. Trolier-McKinstry, Susan

    2015-03-07

    Residual ferroelectricity is observed in barium strontium titanate ceramics over 30 °C above the global phase transition temperature, in the same temperature range in which anomalously large flexoelectric coefficients are reported. The application of a strain gradient leads to strain gradient-induced poling or flexoelectric poling. This was observed by the development of a remanent polarization in flexoelectric measurements, an induced d{sub 33} piezoelectric response even after the strain gradient was removed, and the production of an internal bias of 9 kV m{sup −1}. It is concluded that residual ferroelectric response considerably enhances the observed flexoelectric response.

  17. Strain engineered barium strontium titanate for tunable thin film resonators

    SciTech Connect

    Khassaf, H.; Khakpash, N.; Sun, F.; Sbrockey, N. M.; Tompa, G. S.; Kalkur, T. S.; Alpay, S. P.

    2014-05-19

    Piezoelectric properties of epitaxial (001) barium strontium titanate (BST) films are computed as functions of composition, misfit strain, and temperature using a non-linear thermodynamic model. Results show that through adjusting in-plane strains, a highly adaptive rhombohedral ferroelectric phase can be stabilized at room temperature with outstanding piezoelectric response exceeding those of lead based piezoceramics. Furthermore, by adjusting the composition and the in-plane misfit, an electrically tunable piezoelectric response can be obtained in the paraelectric state. These findings indicate that strain engineered BST films can be utilized in the development of electrically tunable and switchable surface and bulk acoustic wave resonators.

  18. Co,Ti,Mn-precipitated barium hexaferrite powders

    SciTech Connect

    Michalikova, M.; Gruskova, A.; Vicen, R.; Lipka, J.; Slama, J.

    1994-03-01

    Barium ferrites substituted Co, Ti, Mn, produced by the citrate method have been studied. The substitution x in BaCo{sub x}Ti{sub x}Mn{sub y}Fe{sub 12{minus}2x{minus}y}O{sub 19} has been varied from 0.2--2.0 i./f.u. and the substitution of Mn y = 0.1 i./f.u.. Magnetic parameters were measured by the vibration magnetometer. The mechanism of hexagonal structure formation has been checked by Moessbauer spectroscopy.

  19. Graphite Fluoride Fiber Composites For Heat Sinking

    NASA Technical Reports Server (NTRS)

    Hung, Ching-Cheh; Long, Martin; Stahl, Mark

    1989-01-01

    Graphite fluoride fiber/polymer composite materials consist of graphite fluoride fibers in epoxy, polytetrafluoroethylene, or polyimide resin. Combines high electrical resistivity with high thermal conductivity and solves heat-transfer problems of many electrical systems. Commercially available in powder form, for use as dry lubricant or cathode material in lithium batteries. Produced by direct fluorination of graphite powder at temperature of 400 to 650 degree C. Applications include printed-circuit boards for high-density power electronics, insulators for magnetic-field cores like those found in alternators and transformers, substrates for thin-film resistors, and electrical-protection layers in aircraft de-icers.

  20. Evidence against barium in the mushroom Trogia venenata as a cause of sudden unexpected deaths in Yunnan, China.

    PubMed

    Zhang, Ying; Li, Yanchun; Wu, Gang; Feng, Bang; Yoell, Shanze; Yu, Zefen; Zhang, Keqin; Xu, Jianping

    2012-12-01

    This study examined barium concentrations in the mushroom Trogia venenata, the leading culprit for sudden unexpected deaths in Yunnan, southwest China. We found that barium concentrations in T. venenata from Yunnan were low and comparable to other foods, inconsistent with barium concentrations in this mushroom as a significant contributor to these deaths.

  1. Reconstructing temporal variation of fluoride uptake in eastern grey kangaroos (Macropus giganteus) from a high-fluoride area by analysis of fluoride distribution in dentine.

    PubMed

    Kierdorf, Horst; Rhede, Dieter; Death, Clare; Hufschmid, Jasmin; Kierdorf, Uwe

    2016-04-01

    Trace element profiling in the incrementally formed dentine of mammalian teeth can be applied to reconstruct temporal variation of incorporation of these elements into the tissue. Using an electron microprobe, this study analysed fluoride distribution in dentine of first and third mandibular molars of free-ranging eastern grey kangaroos inhabiting a high-fluoride area, to assess temporal variation in fluoride uptake of the animals. Fluoride content in the early-formed dentine of first molars was significantly lower than in the late-formed dentine of these teeth, and was also lower than in both, the early and the late-formed dentine of third molars. As early dentine formation in M1 takes place prior to weaning, this finding indicates a lower dentinal fluoride uptake during the pre-weaning compared to the post-weaning period. This is hypothetically attributed to the action of a partial barrier to fluoride transfer from blood to milk in lactating females and a low bioavailability of fluoride ingested together with milk. Another factor contributing to lower plasma fluoride levels in juveniles compared to adults is the rapid clearance of fluoride from blood plasma in the former due to their intense skeletal growth. The combined action of these mechanisms is considered to explain why in kangaroos from high-fluoride areas, the (early-formed) first molars are not affected by dental fluorosis while the (later-formed) third and fourth molars regularly exhibit marked to severe fluorotic lesions.

  2. Evaluation of gastrointestinal tract transit times using barium-impregnated polyethylene spheres and barium sulfate suspension in a domestic pigeon (Columba livia) model.

    PubMed

    Bloch, Rebecca A; Cronin, Kimberly; Hoover, John P; Pechman, Robert D; Payton, Mark E

    2010-03-01

    Barium impregnated polyethylene spheres (BIPS) are used in small animal medicine as an alternative to barium sulfate for radiographic studies of the gastrointestinal tract. To determine the usefulness of BIPS as an alternative to barium suspension in measuring gastrointestinal (GI) transit time for avian species, ventrodorsal radiographs were used to follow the passage of BIPS and 30% barium sulfate suspension through the GI tracts of domestic pigeons (Columba livia). Gastrointestinal transit times of thirty 1.5-mm BIPS administered in moistened gelatin capsules and 30% barium sulfate suspension gavaged into the crop were compared in 6 pigeons. Although the barium suspension passed out of the GI tract of all pigeons within 24 hours, the 1.5-mm BIPS remained in the ventriculus for 368.0 +/- 176.8 hours and did not clear the GI tract for 424.0 +/- 204.6 hours. Although the times for passage of BIPS and 30% barium sulfate suspension from the crop into the ventriculus were not significantly different (P = .14), the times for passage of BIPS from the ventriculus into the large intestine-cloaca and for clearance from the GI tract of the pigeons were significantly longer (P < .001) than for the 30% barium sulfate suspension. From the results of this study, we conclude that BIPS are not useful for radiographically evaluating GI transit times in pigeons and are unlikely to be useful in other avian species that have a muscular ventriculus. BIPS may or may not be useful for evaluating GI transit times in species that lack a muscular ventriculus.

  3. [Chemical form changes of exogenous water solution fluoride and bioavailability in tea garden soil].

    PubMed

    Cai, Hui-Mei; Peng, Chuan-Yi; Chen, Jing; Hou, Ru-Yan; Wan, Xiao-Chun

    2013-11-01

    Pot experiments and the sequential extraction method were conducted to study the chemical form changes of exogenous water solution fluoride in tea garden soil and their contribution to fluoride accumulation of tea plant. The results showed that the background concentration of all chemical forms of fluoride had little changes with time treatment, which was in a relatively stable state. The exogenous water solution fluoride adding to the soils was rapidly transformed to other fractions. Under the 10 mg x kg(-1) fluoride treatment, the concentration of water solution fluoride increased firstly and then decreased with time treatment, the concentration of organic matter fluoride and Fe/Mn oxides fluoride decreased, the concentration of exchangeable fluoride was not different before and after the treatment (P > 0.05), and the concentration of residual fluoride was in a relatively stable state; under the 200 mg x kg(-1) fluoride treatment, the concentration of water solution fluoride, Fe/Mn oxides fluoride and organic matter fluoride decreased with time treatment, the concentration of exchangeable fluoride increased firstly and then decreased, showed no difference before and after the treatment (P > 0.05), and the concentration of residual fluoride increased, with some differences compared with 10 mg x kg(-1) fluoride treatment. The concentration of total fluoride in root, stem and leaf had significant differences under 0-10 mg x kg(-1) fluoride treatment (P < 0.05), while showed no difference from 10 to 100 mg x kg(-1) fluoride treatment (P > 0.05). Step regression analysis suggested the contribution of all chemical forms of fluoride to the concentration of water solution fluoride and total fluoride of root, stem and leaf had some differences, there was a remarkable regression relationship among the content of total fluoride in leaf and water solution fluoride, organic matter fluoride, Fe/Mn oxides fluoride and residual fluoride in soil, however, no significant

  4. Synthesis of complex fluorides for optical applications

    NASA Astrophysics Data System (ADS)

    Stepleton, Seth Eugene

    Large single crystals of alkali metal fluorides are desirable for many reasons. Fluoride laser crystals have a wide transmission range and on account of their low phonon energies, many efficient laser emissions have been obtained from 285 nm to 4.34 microm.1,2 Inorganic fluoride single crystals feature large bandgaps, very wide optical transmittance ranges from vacuum-ultraviolet (VUV) to mid-IR wavelength regions, lower refractive indices than those of oxides, and typically lower phonon energies (which drastically reduce multiphonon relaxation rates of rare earth ions).3 The main goal of this work was to investigate the hydrothermal synthesis of alkali metal fluorides. Melt techniques have been used thoroughly to research a variety of fluoride systems and showed many phases that were inaccessible due to incongruent melting or phase stability. The existence of these phases was shown but never characterized or grown as a crystalline material. Solution growth in supercritical water was an ideal way to attempt the synthesis of novel compounds and phases. New synthetic routes to known phases and compounds also arose as a part of this work. Optically clear colorless crystals of K2BeF4 were synthesized up to 2 mm in size, and showed no phase transitions up to 1029 K, which suggests paraelectricitys at room temperature, contradicting previous reports.4 Attempts to incorporate a rare earth ion into the fluoroberyllate lattice proved unsuccessful however reactions between beryllium fluoride and lanthanide fluorides could be exploited as a synthetic route to single crystal rare earth fluorides. Hydrothermal reactions with KF produced crystals of three different phases: hexagonal KY2F7, trigonal KYF4 and orthorhombic K2YF5. All were optically clear, colorless crystals, with the K2YF5 crystals growing the largest. This compound is beneficial due to its application as a radiation dosimeter and laser host. 5,6 Optical quality colorless crystals of RbY2F7 and CsY2F7 up to 4 mm in

  5. Tungsten and Barium Transport in the Internal Plasma of Hollow Cathodes

    NASA Technical Reports Server (NTRS)

    Polk, James E.; Mikellides, Ioannis G.; Katz, Ira; Capece, Angela M.

    2008-01-01

    The effect of tungsten erosion, transport and redeposition on the operation of dispenser hollow cathodes was investigated in detailed examinations of the discharge cathode inserts from an 8200 hour and a 30,352 hour ion engine wear test. Erosion and subsequent re-deposition of tungsten in the electron emission zone at the downstream end of the insert reduces the porosity of the tungsten matrix, preventing the flow of barium from the interior. This inhibits the interfacial reactions of the barium-calcium-aluminate impregnant with the tungsten in the pores. A numerical model of barium transport in the internal xenon discharge plasma shows that the barium required to reduce the work function in the emission zone can be supplied from upstream through the gas phase. Barium that flows out of the pores of the tungsten insert is rapidly ionized in the xenon discharge and pushedback to the emitter surface by the electric field and drag from the xenon ion flow. Thisbarium ion flux is sufficient to maintain a barium surface coverage at the downstream endgreater than 0.6, even if local barium production at that point is inhibited by tungsten deposits. The model also shows that the neutral barium pressure exceeds the equilibrium vapor pressure of the impregnant decomposition reaction over much of the insert length,so the reactions are suppressed. Only a small region upstream of the zone blocked by tungsten deposits is active and supplies the required barium. These results indicate that hollowcathode failure models based on barium depletion rates in vacuum dispenser cathodes are very conservative.

  6. Fluoride release from restorative materials.

    PubMed

    Basso, Gabriela Romanini; Della Bona, Alvaro; Gobbi, Delton Luiz; Cecchetti, Dileta

    2011-01-01

    The aim of this study was to evaluate in vitro fluoride (F) release from 4 restorative materials (3M ESPE): Ketak Molar Easymix [KME - conventional glass ionomer cement (GIC)]; Rely-X luting 2 [RL2 - resin-modified GIC (RMGIC)]; Vitremer (VIT- RMGIC); and Filtek Z250 [Z250 - negative control]. Disc-shaped specimens were fabricated according to the manufacturer's instructions and placed into 10 mL of reverse osmosis water at 37°C until the analyses were done using a liquid membrane for selective F ion electrode (Orion 710). F release was evaluated every 6 h in the first day and thereafter daily during 28 days (d). The results were analyzed statistically by two-way ANOVA and Tukey's test (α=0.05). Mean F release and standard deviation values (in ppm) were: KME: 6 h- 0.34 ± 0.04; 24 h- 1.22 ± 0.30; 7 d- 0.29 ± 0.09; 14 d- 0.20 ± 0.04; 28 d- 0.16 ± 0.01; RL2: 6 h- 2.46 ± 0.48; 24 h-12.33 ± 2.93; 7 d- 1.37 ± 0.38; 14 d- 0.80 ± 0.13; 28 d- 0.80 ± 0.21; VIT: 6 h- 0.98 ± 0.35; 24 h- 4.35 ± 1.22; 7 d- 0.66 ± 0.23; 14 d- 0.40 ± 0.07; 28 d- 0.39 ± 0.08; Z250: 6 h- 0.029 ± 0.001; 24 h- 0.024 ± 0.009; 7 d- 0.023 ± 0.004; 14 d- 0.025 ± 0.001; 28 d- 0.028 ± 0.001. RL2 RMGIC released more F than the other materials in all periods. The greatest release of F occurred in the first 24 h.

  7. An exclusive fluoride receptor: Fluoride-induced proton transfer to a quinoline-based thiourea

    PubMed Central

    Basaran, Ismet; Khansari, Maryam Emami; Pramanik, Avijit; Wong, Bryan M.; Hossain, Alamgir

    2014-01-01

    A new quinoline-based tripodal thiourea has been synthesized, which exclusively binds fluoride anion in DMSO, showing no affinity for other anions including, chloride, bromide, iodide, perchlorate, nitrate and hydrogen sulfate. As investigated by 1H NMR, the receptor forms both 1:1 and 1:2 complex yielding the binding constants of 2.32(3) (in log β1) and 4.39(4) (in log β2), respectively; where quinoline groups are protonated by the fluoride-induced proton transfer from the solution to the host molecule. The 1:2 binding is due to the interactions of one fluoride with NH binding sites of urea sites and another fluoride with secondary +NH binding sites within the tripodal pocket. The formation of both 1:1 and 1:2 complexes has been confirmed by the theoretical calculations based on density functional theory (DFT). PMID:24753636

  8. Some electronic and magnetic properties of Fluoride ion in Fluoride structure nanocrystals

    NASA Astrophysics Data System (ADS)

    Imtani, Ali Nasir

    2012-01-01

    We have investigated the effects of the environment potential around Fluoride ion on some important electronic and magnetic properties such as dipole polarisability, moment of oscillator strengths S(k) and magnetic susceptibility. The theoretical procedure is based on the variational-perturbation theory with two parameter trial functions incorporated in an ionic model. We estimate these properties in four cases for Fluoride ion; free ion, ion under different potentials, ion in the crystals and ion in nanocrystal, CdF2, CaF2, PbF2, SrF2 and BaF2. Our results indicate that these properties vary with ion environments and the free state of Fluoride ion has higher values and there is linearity behaviour of these properties with lattice constant. For Fluoride ion in nanocrystal, we have found that there is an extra parameter that can also affect the dipole polarisability, the number of ions in the structure.

  9. Red blood cell glucose metabolism in human chronic fluoride toxicity

    SciTech Connect

    Saralakumari, D.; Rao, P.R. )

    1991-12-01

    Fluoride is a well known inhibitor of many enzyme systems in vitro. The most widely studied classic example of fluoride inhibition is its potent inhibition of glycolysis, specifically its action on the enzyme enolase. Despite the plethora of in vitro studies on the effects of fluoride on the enzyme activity, there is a paucity of information concerning the in vivo metabolic lesions caused by the chronic toxic doses of fluoride in humans. The present study has been undertaken with a view to assess the changes in glucose metabolism and related enzymes in erythrocytes of humans consuming toxic doses of fluoride for prolonged periods.

  10. PROCESS FOR THE PRODUCTION OF AMMONIUM URANIUM FLUORIDE

    DOEpatents

    Ellis, A.S.; Mooney, R.B.

    1953-08-25

    This patent relates to the preparation of ammonium uranium fluoride. The process comprises adding a water soluble fluoride to an aqueous solution of a uranous compound containing an ammonium salt, and isolating the resulting precipitate. This patent relates to the manufacture of uranium tetnafluoride from ammonium uranium fluoride, NH/sub 4/UF/sub 5/. Uranium tetrafluoride is prepared by heating the ammonium uranium fluoride to a temperature at which dissociation occurs with liberation of ammonium fluoride. Preferably the process is carried out under reduced pressure, or in a current of an inert gas.

  11. Fluorides - mode of action and recommendations for use.

    PubMed

    Lussi, Adrian; Hellwig, Elmar; Klimek, Joachim

    2012-01-01

    Various authors have shown that the caries decline in the industrialized countries during recent decades is based on the use of fluorides, of which local fluoride application in the form of fluoridated toothpastes is of primary importance. The caries-protective potential of fluorapatite is quite low; in contrast, dissolved fluorides in the vicinity of enamel are effective both in promoting remineralization and inhibiting demineralization. Considering the fact that the caries decline occurred at the same time that local fluoridation measures became widely used, the conclusion seems justified that regular application of F⁻ can inhibit caries.

  12. Fluoride geochemistry of thermal waters in Yellowstone National Park: I. Aqueous fluoride speciation

    USGS Publications Warehouse

    Deng, Y.; Nordstrom, D.K.; Blaine, McCleskey R.

    2011-01-01

    Thermal water samples from Yellowstone National Park (YNP) have a wide range of pH (1-10), temperature, and high concentrations of fluoride (up to 50mg/l). High fluoride concentrations are found in waters with field pH higher than 6 (except those in Crater Hills) and temperatures higher than 50??C based on data from more than 750 water samples covering most thermal areas in YNP from 1975 to 2008. In this study, more than 140 water samples from YNP collected in 2006-2009 were analyzed for free-fluoride activity by ion-selective electrode (ISE) method as an independent check on the reliability of fluoride speciation calculations. The free to total fluoride concentration ratio ranged from <1% at low pH values to >99% at high pH. The wide range in fluoride activity can be explained by strong complexing with H+ and Al3+ under acidic conditions and lack of complexing under basic conditions. Differences between the free-fluoride activities calculated with the WATEQ4F code and those measured by ISE were within 0.3-30% for more than 90% of samples at or above 10-6 molar, providing corroboration for chemical speciation models for a wide range of pH and chemistry of YNP thermal waters. Calculated speciation results show that free fluoride, F-, and major complexes (HF(aq)0, AlF2+, AlF2+ and AlF30) account for more than 95% of total fluoride. Occasionally, some complex species like AlF4-, FeF2+, FeF2+, MgF+ and BF2(OH)2- may comprise 1-10% when the concentrations of the appropriate components are high. According to the simulation results by PHREEQC and calculated results, the ratio of main fluoride species to total fluoride varies as a function of pH and the concentrations and ratios of F and Al. ?? 2011.

  13. Barium titanate core – gold shell nanoparticles for hyperthermia treatments

    PubMed Central

    FarrokhTakin, Elmira; Ciofani, Gianni; Puleo, Gian Luigi; de Vito, Giuseppe; Filippeschi, Carlo; Mazzolai, Barbara; Piazza, Vincenzo; Mattoli, Virgilio

    2013-01-01

    The development of new tools and devices to aid in treating cancer is a hot topic in biomedical research. The practice of using heat (hyperthermia) to treat cancerous lesions has a long history dating back to ancient Greece. With deeper knowledge of the factors that cause cancer and the transmissive window of cells and tissues in the near-infrared region of the electromagnetic spectrum, hyperthermia applications have been able to incorporate the use of lasers. Photothermal therapy has been introduced as a selective and noninvasive treatment for cancer, in which exogenous photothermal agents are exploited to achieve the selective destruction of cancer cells. In this manuscript, we propose applications of barium titanate core–gold shell nanoparticles for hyperthermia treatment against cancer cells. We explored the effect of increasing concentrations of these nanoshells (0–100 μg/mL) on human neuroblastoma SH-SY5Y cells, testing the internalization and intrinsic toxicity and validating the hyperthermic functionality of the particles through near infrared (NIR) laser-induced thermoablation experiments. No significant changes were observed in cell viability up to nanoparticle concentrations of 50 μg/mL. Experiments upon stimulation with an NIR laser revealed the ability of the nanoshells to destroy human neuroblastoma cells. On the basis of these findings, barium titanate core–gold shell nanoparticles resulted in being suitable for hyperthermia treatment, and our results represent a promising first step for subsequent investigations on their applicability in clinical practice. PMID:23847415

  14. Monte Carlo calculations of the microstructure of barium ferrite dispersions

    NASA Astrophysics Data System (ADS)

    Walmsley, N. S.; Coverdale, G. N.; Chantrell, R. W.; Parker, D. A.; Bissell, P. R.

    1998-07-01

    A Monte Carlo (MC) model has been developed to investigate the influences of the volume packing fraction and applied field on the equilibrium microstructure of a dispersion of barium ferrite particles. We accounted for magnetostatic interaction effects by using a surface charge model which allows the calculation of the energy term required for the Metropolis-type MC algorithm. In addition to single particle moves, the model employs a clustering algorithm, based on particle proximity, in order to take into account the cooperative behaviour of the particles bound by magnetostatic energy. The stacks which are thought to be characteristic of barium ferrite systems are an example of this type of binding. Our study provides strong evidence, in agreement with experiment, for the formation of stacks both in the zero field and in the applied field equilibrium configurations. The simulation also predicts, by considering the effects of the packing density, that the dispersion properties are strongly affected by the mobility of these stacks. The equilibrium particle configurations have been investigated using a correlation function and visualized by computer graphics. The magnetic behaviour has been investigated by calculation of the magnetization curve.

  15. Brillouin function characteristics for La-Co substituted barium hexaferrites

    NASA Astrophysics Data System (ADS)

    Wu, Chuanjian; Yu, Zhong; Yang, Yan; Sun, Ke; Guo, Rongdi; Jiang, Xiaona; Lan, Zhongwen

    2015-09-01

    La-Co substituted barium hexaferrites with the chemical formula of Ba1-xLaxFe12-xCoxO19 (x = 0.0, 0.1, 0.3, and 0.5), prepared by a conventional ceramic method, were systematically investigated by Raman spectra, X-ray photoelectron spectroscopy, Rietveld refinement of X-ray diffraction patterns, and vibrating sample magnetometer. The result manifests that all the compounds are crystallized in magnetoplumbite hexagonal structure. Trivalent cobalt ions prevailingly occupy the 2a, 4f1, and 12k sites. According to Néel model of collinear-spin ferrimagnetism, the molecular-field coefficients ωbf2, ωkf1, ωaf1, ωkf2, and ωbk of La-Co substituted barium hexaferrites have been calculated using the nonlinear fitting method, and the magnetic moment of five sublattices (2a, 2b, 4f1, 4f2, and 12k) versus temperature T has been also investigated. The fitting results are coincided well with the experimental data. Moreover, with the increase of La-Co substitution amount x, the molecular-field coefficients ωbf2 and ωaf1 decrease constantly, while the molecular-field coefficients ωkf1, ωkf2, and ωbk show a slight change.

  16. Synthesis of Barium Titanate Using Deep Eutectic Solvents.

    PubMed

    Boston, Rebecca; Foeller, Philip Y; Sinclair, Derek C; Reaney, Ian M

    2017-01-03

    Novel synthetic routes to prepare functional oxides at lower temperatures are an increasingly important area of research. Many of these synthetic routes, however, use water as the solvent and rely on dissolution of the precursors, precluding their use with, for example, titanates. Here we present a low-cost solvent system as a means to rapidly create phase-pure ferroelectric barium titanate using a choline chloride-malonic acid deep eutectic solvent. This solvent is compatible with alkoxide precursors and allows for the rapid synthesis of nanoscale barium titanate powders at 950 °C. The phase and morphology were determined, along with investigation of the synthetic pathway, with the reaction proceeding via BaCl2 and TiO2 intermediates. The powders were also used to create sintered ceramics, which exhibit a permittivity maximum corresponding to a tetragonal-cubic transition at 112 °C, as opposed to the more conventional temperature of ∼120 °C. The lower-than-expected value for the ferro- to para-electric phase transition is likely due to undetectable levels of contaminants.

  17. Plasma waves associated with the first AMPTE magnetotail barium release

    NASA Technical Reports Server (NTRS)

    Gurnett, D. A.; Anderson, R. R.; Bernhardt, P. A.; Luehr, H.; Haerendel, G.

    1986-01-01

    Plasma waves observed during the March 21, 1985, AMPTE magnetotail barium release are described. Electron plasma oscillations provided local measurements of the plasma density during both the expansion and decay phases. Immediately after the explosion, the electron density reached a peak of about 400,000/cu cm, and then started decreasing approximately as t to the -2.4 as the cloud expanded. About 6 minutes after the explosion, the electron density suddenly began to increase, reached a secondary peak of about 240/cu cm, and then slowly decayed down to the preevent level over a period of about 15 minutes. The density increase is believed to be caused by the collapse of the ion cloud into the diamagnetic cavity created by the initial expansion. The plasma wave intensities observed during the entire event were quite low. In the diamagnetic cavity, electrostatic emissions were observed near the barium ion plasma frequency, and in another band at lower frequencies. A broadband burst of electrostatic noise was also observed at the boundary of the diamagnetic cavity. Except for electron plasma oscillations, no significant wave activity was observed outside of the diamagnetic cavity.

  18. Structural and optical study of tellurite-barium glasses

    NASA Astrophysics Data System (ADS)

    Grelowska, I.; Reben, M.; Burtan, B.; Sitarz, M.; Cisowski, J.; Yousef, El Sayed; Knapik, A.; Dudek, M.

    2016-12-01

    The goal of this work was to determine the effect of barium oxide on the structural, thermal and optical properties of the TeO2-BaO-Na2O (TBN) and TeO2-BaO-WO3 (TBW) glass systems. Raman spectra allow relating the glass structure and vibration properties (i.e. vibrational frequencies and Raman intensities) with the glass composition. Raman spectra show the presence of TeO4 and TeO3+1/TeO3 units that conform with the glass matrix. Differential thermal analysis DTA, XRD measurements have been considered in term of BaO addition. The spectral dependence of ellipsometric angles of the tellurite-barium glass has been studied. The optical measurements were conducted on Woollam M2000 spectroscopic ellipsometer in spectral range of 190-1700 nm. The reflectance and transmittance measurements have been done on spectrophotometer Perkin Elmer, Lambda 900 in the range of 200-2500 nm (UV-VIS-NIR). From the transmittance spectrum, the energy gap was determined.

  19. Appropriate uses of fluorides for children: guidelines from the Canadian Workshop on the Evaluation of Current Recommendations Concerning Fluorides.

    PubMed Central

    Clark, D C

    1993-01-01

    OBJECTIVE: To prevent fluorosis caused by excessive fluoride ingestion by revising recommendations for fluoride intake by children. OPTIONS: Limiting fluoride ingestion from fluoridated water, fluoride supplements and fluoride dentifrices. OUTCOMES: Reduction in the prevalence of dental fluorosis and continued prevention of dental caries. EVIDENCE: Before the workshop, experts prepared comprehensive literature reviews of fluoride therapies, fluoride ingestion and the prevalence and causes of dental fluorosis. The papers, which were peer-reviewed, revised and circulated to the workshop participants, formed the basis of the workshop discussions. VALUES: Recommendations to limit fluoride intake were vigorously debated before being adopted as the consensus opinion of the workshop group. BENEFITS, HARMS AND COSTS: Decrease in the prevalence of dental fluorosis with continuing preventive effects of fluoride use. The only significant cost would be in preparing new, low-concentration fluoride products for distribution. RECOMMENDATIONS: Fluoride supplementation should be limited to children 3 years of age and older in areas where there is less than 0.3 ppm of fluoride in the water supply. Children in all areas should use only a "pea-sized" amount of fluoride dentifrice no more than twice daily under the supervision of an adult. VALIDATION: These recommendations are almost identical to changes to recommendations for the use of fluoride supplements recently proposed by a group of European countries. SPONSORS: The workshop was organized by Dr. D. Christopher Clark, of the University of British Columbia, and Drs. Hardy Limeback and Ralph C. Burgess, of the University of Toronto, and funded by Proctor and Gamble Inc., Toronto, the Medical Research Council of Canada and Health Canada (formerly the Department of National Health and Welfare). The recommendations were formally adopted by the Canadian Dental Association in April 1993. PMID:8261348

  20. Fluoride Content of Bottled Drinking Water in Chennai, Tamilnadu

    PubMed Central

    Ravi, Karunya; Rajapandian, K.; Gurunathan, Deepa

    2015-01-01

    Context The optimum level of fluoride in drinking water is 0.7 to 1.2 ppm. Decreased fluoride concentration leads to increased risk of caries and increased concentration can lead to dental or skeletal fluorosis. One crore liters of water is supplied to Chennai and surrounding areas through pouches and bottles which carters about one third of city population. Aim The aim of this study is to determine the fluoride concentration in top 10 bottled waters in Chennai and to check the accuracy of their labelling. Materials and Methods Top selling bottled waters, 6 multinational and 4 Non- multinational brands were selected for the study. Three different batches of each brand were purchased. The labels of the bottled were removed after collecting the details regarding fluoride content. All the bottles were numbered and sent for fluoride content analysis using SPADNS calorimetric method. Results All the brands and batches which were analysed for the study had less than optimal fluoride content and there is a significant variation in fluoride concentration of each brand and among different batches of same brand bottled waters. The range of fluoride level in tested samples was between 0.27 to 0.59. Only one brand’s label had information regarding the fluoride content. Conclusion Standardization of fluoride levels in bottled waters and labelling of fluoride content should become mandatory. PMID:26557612

  1. Liquid-Phase Processing of Barium Titanate Thin Films

    NASA Astrophysics Data System (ADS)

    Harris, David Thomas

    Processing of thin films introduces strict limits on the thermal budget due to substrate stability and thermal expansion mismatch stresses. Barium titanate serves as a model system for the difficulty in producing high quality thin films because of sensitivity to stress, scale, and crystal quality. Thermal budget restriction leads to reduced crystal quality, density, and grain growth, depressing ferroelectric and nonlinear dielectric properties. Processing of barium titanate is typically performed at temperatures hundreds of degrees above compatibility with metalized substrates. In particular integration with silicon and other low thermal expansion substrates is desirable for reductions in costs and wider availability of technologies. In bulk metal and ceramic systems, sintering behavior has been encouraged by the addition of a liquid forming second phase, improving kinetics and promoting densification and grain growth at lower temperatures. This approach is also widespread in the multilayer ceramic capacitor industry. However only limited exploration of flux processing with refractory thin films has been performed despite offering improved dielectric properties for barium titanate films at lower temperatures. This dissertation explores physical vapor deposition of barium titanate thin films with addition of liquid forming fluxes. Flux systems studied include BaO-B2O3, Bi2O3-BaB2O 4, BaO-V2O5, CuO-BaO-B2O3, and BaO-B2O3 modified by Al, Si, V, and Li. Additions of BaO-B2O3 leads to densification and an increase in average grain size from 50 nm to over 300 nm after annealing at 900 °C. The ability to tune permittivity of the material improved from 20% to 70%. Development of high quality films enables engineering of ferroelectric phase stability using residual thermal expansion mismatch in polycrystalline films. The observed shifts to TC match thermodynamic calculations, expected strain from the thermal expansion coefficients, as well as x-ray diffract measurements

  2. Estimated Fluoride Doses from Toothpastes Should be Based on Total Soluble Fluoride

    PubMed Central

    Oliveira, Maria José L.; Martins, Carolina C.; Paiva, Saul M.; Tenuta, Livia M. A.; Cury, Jaime A.

    2013-01-01

    The fluoride dose ingested by young children may be overestimated if based on levels of total fluoride (TF) rather than levels of bioavailable fluoride (total soluble fluoride—TSF) in toothpaste. The aim of the present study was to compare doses of fluoride intake based on TF and TSF. Fluoride intake in 158 Brazilian children aged three and four years was determined after tooth brushing with their usual toothpaste (either family toothpaste (n = 80) or children’s toothpaste (n = 78)). The estimated dose (mg F/day/Kg of body weight) of TF or TSF ingested was calculated from the chemical analysis of the toothpastes. Although the ingested dose of TF from the family toothpastes was higher than that from the children’s toothpastes (0.074 ± 0.007 and 0.039 ± 0.003 mg F/day/Kg, respectively; p < 0.05), no difference between types of toothpaste was found regarding the ingested dose based on TSF (0.039 ± 0.005 and 0.039 ± 0.005 mg F/day/Kg, respectively; p > 0.05). The fluoride dose ingested by children from toothpastes may be overestimated if based on the TF of the product. This finding suggests that the ingested dose should be calculated based on TSF. Dose of TSF ingested by children is similar whether family or children’s toothpaste is used. PMID:24189183

  3. FLUORIDE CONTENT OF COMMERCIALLY AVAILABLE SOY MILK PRODUCTS IN THAILAND.

    PubMed

    Rirattanapong, Opas; Rirattanapong, Praphasri

    2016-01-01

    Abstract. In Thailand, the consumption of soy milk products is common but there is limited data about their fluoride content. The purpose of this study was to es- timate the fluoride content of soy milk products available in Thailand. Fluoride content was determined for 76 brands of soy milk using a F-ion-specific electrode. The fluoride concentrations ranged from 0.01 to 3.78 μg/ml. The fluoride content was not related to sugar content, soy bean content or the sterilization process. Among 3 brands of soy milk containing tea powder extract, the fluoride content was high (1.25 to 3.78 μg/ml). Most brands of soy milk tested in our study had fluoride content below the optimal daily intake but brands containing tea powder extract if consumed by children may increase their risk for fluorosis.

  4. [Fluoride emission from different soil minerals at high temperatures].

    PubMed

    Wu, W; Xie, Z; Xu, J; Liu, C

    2001-03-01

    The emission characteristics of fluoride pollutants from montmorillonite, kaolinite, vermiculite, geothite and allophane were studied to elucidate the mechanism of fluoride-releasing from soils during brick and tile making at high temperatures from 300 degrees C to 1000 degrees C. The rate of fluoride emission varied with temperature, mineral type, heating time, specific surface area and cations added to minerals. The escape of crystalline water resulting from crystal lattice collapse at a certain high temperature was found to affect the rate of fluoride emission. Calcium compounds could decrease fluoride emission rate from montmorillonite. At 800 degrees C, the rate of fluoride emission from Ca-treated montmorillonite decreased by 59.6% compared to untreated montmorillonite. The order for fluoride-fixing capacity of the 5 calcium compounds at 800 degrees C was as follows: CaCO3 > CaO > Ca3(PO4)2 > Ca(OH)2 > CaSO4.

  5. Palladium-catalyzed substitution of allylic fluorides.

    PubMed

    Hazari, Amaruka; Gouverneur, Véronique; Brown, John M

    2009-01-01

    As unusual substrates for the Tsuji-Trost allylation reaction, allylic fluorides are responsive to palladium-catalyzed substitution. Their activity towards this reaction fits in the series OCO(2)Me>OBz>F>OAc. The classic stereoretention mechanism that involves sequential inversions does not operate in this case. Several distinct cases are considered.

  6. Surface crystallization of a fluoride glass

    NASA Technical Reports Server (NTRS)

    Bansal, Narottam P.; Doremus, Robert H.

    1983-01-01

    Growth of crystals on the surface of a Zr-Ba-La fluoride glass was observed by optical and scanning electron microscopy. Small, dark crystal nucleated rapidly and grew to a size of about 10 microns; then they stopped growing, and wrinkled regions emerged, covering the entire crystal surface.

  7. Aqueous vinylidene fluoride polymer coating composition

    NASA Technical Reports Server (NTRS)

    Bartoszek, Edward J. (Inventor); Christofas, Alkis (Inventor)

    1978-01-01

    A water-based coating composition which may be air dried to form durable, fire resistant coatings includes dispersed vinylidene fluoride polymer particles, emulsified liquid epoxy resin and a dissolved emulsifying agent for said epoxy resin which agent is also capable of rapidly curing the epoxy resin upon removal of the water from the composition.

  8. Actinide measurements by AMS using fluoride matrices

    NASA Astrophysics Data System (ADS)

    Cornett, R. J.; Kazi, Z. H.; Zhao, X.-L.; Chartrand, M. G.; Charles, R. J.; Kieser, W. E.

    2015-10-01

    Actinides can be measured by alpha spectroscopy (AS), mass spectroscopy or accelerator mass spectrometry (AMS). We tested a simple method to separate Pu and Am isotopes from the sample matrix using a single extraction chromatography column. The actinides in the column eluent were then measured by AS or AMS using a fluoride target matrix. Pu and Am were coprecipitated with NdF3. The strongest AMS beams of Pu and Am were produced when there was a large excess of fluoride donor atoms in the target and the NdF3 precipitates were diluted about 6-8 fold with PbF2. The measured concentrations of 239,240Pu and 241Am agreed with the concentrations in standards of known activity and with two IAEA certified reference materials. Measurements of 239,240Pu and 241Am made at A.E. Lalonde AMS Laboratory agree, within their statistical uncertainty, with independent measurements made using the IsoTrace AMS system. This work demonstrated that fluoride targets can produce reliable beams of actinide anions and that the measurement of actinides using fluorides agree with published values in certified reference materials.

  9. Innovative Monitoring of Atmospheric Gaseous Hydrogen Fluoride

    PubMed Central

    Bonari, Alessandro; Pompilio, Ilenia; Monti, Alessandro; Arcangeli, Giulio

    2016-01-01

    Hydrogen fluoride (HF) is a basic raw material for a wide variety of industrial products, with a worldwide production capacity of more than three million metric tonnes. A novel method for determining particulate fluoride and gaseous hydrogen fluoride in air is presented herewith. Air was sampled using miniaturised 13 mm Swinnex two-stage filter holders in a medium-flow pumping system and through the absorption of particulate fluoride and HF vapours on cellulose ester filters uncoated or impregnated with sodium carbonate. Furthermore, filter desorption from the holders and the extraction of the pentafluorobenzyl ester derivative based on solid-phase microextraction were performed using an innovative robotic system installed on an xyz autosampler on-line with gas chromatography (GC)/mass spectrometry (MS). After generating atmospheres of a known concentration of gaseous HF, we evaluated the agreement between the results of our sampling method and those of the conventional preassembled 37 mm cassette (±8.10%; correlation coefficient: 0.90). In addition, precision (relative standard deviation for n = 10, 4.3%), sensitivity (0.2 μg/filter), and linearity (2.0–4000 μg/filter; correlation coefficient: 0.9913) were also evaluated. This procedure combines the efficiency of GC/MS systems with the high throughput (96 samples/day) and the quantitative accuracy of pentafluorobenzyl bromide on-sample derivatisation. PMID:27829835

  10. Water fluoridation in 40 Brazilian cities: 7 year analysis

    PubMed Central

    MOIMAZ, Suzely Adas Saliba; SALIBA, Nemre Adas; SALIBA, Orlando; SUMIDA, Doris Hissako; de SOUZA, Neila Paula; CHIBA, Fernando Yamamoto; GARBIN, Cléa Adas Saliba

    2013-01-01

    Objectives: Fluoride levels in the public water supplies of 40 Brazilian cities were analyzed and classified on the basis of risk/benefit balance. Material and Methods: Samples were collected monthly over a seven-year period from three sites for each water supply source. The samples were analyzed in duplicate in the laboratory of the Center for Research in Public Health - UNESP using an ion analyzer coupled to a fluoride-specific electrode. Results: A total of 19,533 samples were analyzed, of which 18,847 were artificially fluoridated and 686 were not artificially fluoridated. In samples from cities performing water fluoridation, 51.57% (n=9,720) had fluoride levels in the range of 0.55 to 0.84 mg F/L; 30.53% (n=5,754) were below 0.55 mg F/L and 17.90% (n=3,373) were above 0.84 mg F/L (maximum concentration=6.96 mg F/L). Most of the cities performing fluoridation that had a majority of samples with fluoride levels above the recommended parameter had deep wells and more than one source of water supply. There was some variability in the fluoride levels of samples from the same site and between collection sites in the same city. Conclusions: The majority of samples from cities performing fluoridation had fluoride levels within the range that provides the best combination of risks and benefits, minimizing the risk of dental fluorosis while preventing dental caries. The conduction of studies about water distribution systems is suggested in cities with high natural fluoride concentrations in order to optimize the use of natural fluoride for fluoridation costs and avoid the risk of dental fluorosis. PMID:23559106

  11. Barium zirconate-titanate/barium calcium-titanate ceramics via sol-gel process: novel high-energy-density capacitors

    NASA Astrophysics Data System (ADS)

    Sreenivas Puli, Venkata; Kumar, Ashok; Chrisey, Douglas B.; Tomozawa, M.; Scott, J. F.; Katiyar, Ram S.

    2011-10-01

    Lead-free barium zirconate-titanate/barium calcium-titanate, [(BaZr0.2Ti0.80)O3]1-x-[(Ba0.70Ca0.30)TiO3]x (x = 0.10, 0.15, 0.20) (BZT-BCT) ceramics with high dielectric constant, low dielectric loss and moderate electric breakdown field were prepared by the sol-gel synthesis technique. X-ray diffraction patterns revealed tetragonal crystal structure and this was further confirmed by Raman spectra. Well-behaved ferroelectric hysteresis loops and moderate polarizations (spontaneous polarization, Ps ~ 3-6 µC cm-2) were obtained in these BZT-BCT ceramics. Frequency-dependent dielectric spectra confirmed that ferroelectric diffuse phase transition (DPT) exists near room temperature. Scanning electron microscope images revealed monolithic grain growth in samples sintered at 1280 °C. 1000/ɛ versus (T) plots revealed ferroelectric DPT behaviour with estimated γ values of ~1.52, 1.51 and 1.88, respectively, for the studied BZT-BCT compositions. All three compositions showed packing-limited breakdown fields of ~47-73 kV cm-1 with an energy density of 0.05-0.6 J cm-3 for thick ceramics (>1 mm). Therefore these compositions might be useful in Y5V-type capacitor applications.

  12. Water fluoridation: a critical review of the physiological effects of ingested fluoride as a public health intervention.

    PubMed

    Peckham, Stephen; Awofeso, Niyi

    2014-01-01

    Fluorine is the world's 13th most abundant element and constitutes 0.08% of the Earth crust. It has the highest electronegativity of all elements. Fluoride is widely distributed in the environment, occurring in the air, soils, rocks, and water. Although fluoride is used industrially in a fluorine compound, the manufacture of ceramics, pesticides, aerosol propellants, refrigerants, glassware, and Teflon cookware, it is a generally unwanted byproduct of aluminium, fertilizer, and iron ore manufacture. The medicinal use of fluorides for the prevention of dental caries began in January 1945 when community water supplies in Grand Rapids, United States, were fluoridated to a level of 1 ppm as a dental caries prevention measure. However, water fluoridation remains a controversial public health measure. This paper reviews the human health effects of fluoride. The authors conclude that available evidence suggests that fluoride has a potential to cause major adverse human health problems, while having only a modest dental caries prevention effect. As part of efforts to reduce hazardous fluoride ingestion, the practice of artificial water fluoridation should be reconsidered globally, while industrial safety measures need to be tightened in order to reduce unethical discharge of fluoride compounds into the environment. Public health approaches for global dental caries reduction that do not involve systemic ingestion of fluoride are urgently needed.

  13. Water Fluoridation: A Critical Review of the Physiological Effects of Ingested Fluoride as a Public Health Intervention

    PubMed Central

    2014-01-01

    Fluorine is the world's 13th most abundant element and constitutes 0.08% of the Earth crust. It has the highest electronegativity of all elements. Fluoride is widely distributed in the environment, occurring in the air, soils, rocks, and water. Although fluoride is used industrially in a fluorine compound, the manufacture of ceramics, pesticides, aerosol propellants, refrigerants, glassware, and Teflon cookware, it is a generally unwanted byproduct of aluminium, fertilizer, and iron ore manufacture. The medicinal use of fluorides for the prevention of dental caries began in January 1945 when community water supplies in Grand Rapids, United States, were fluoridated to a level of 1 ppm as a dental caries prevention measure. However, water fluoridation remains a controversial public health measure. This paper reviews the human health effects of fluoride. The authors conclude that available evidence suggests that fluoride has a potential to cause major adverse human health problems, while having only a modest dental caries prevention effect. As part of efforts to reduce hazardous fluoride ingestion, the practice of artificial water fluoridation should be reconsidered globally, while industrial safety measures need to be tightened in order to reduce unethical discharge of fluoride compounds into the environment. Public health approaches for global dental caries reduction that do not involve systemic ingestion of fluoride are urgently needed. PMID:24719570

  14. Multiple inorganic toxic substances contaminating the groundwater of Myingyan Township, Myanmar: arsenic, manganese, fluoride, iron, and uranium.

    PubMed

    Bacquart, Thomas; Frisbie, Seth; Mitchell, Erika; Grigg, Laurie; Cole, Christopher; Small, Colleen; Sarkar, Bibudhendra

    2015-06-01

    In South Asia, the technological and societal shift from drinking surface water to groundwater has resulted in a great reduction of acute diseases due to water borne pathogens. However, arsenic and other naturally occurring inorganic toxic substances present in groundwater in the region have been linked to a variety of chronic diseases, including cancers, heart disease, and neurological problems. Due to the highly specific symptoms of chronic arsenic poisoning, arsenic was the first inorganic toxic substance to be noticed at unsafe levels in the groundwater of West Bengal, India and Bangladesh. Subsequently, other inorganic toxic substances, including manganese, uranium, and fluoride have been found at unsafe levels in groundwater in South Asia. While numerous drinking water wells throughout Myanmar have been tested for arsenic, relatively little is known about the concentrations of other inorganic toxic substances in Myanmar groundwater. In this study, we analyzed samples from 18 drinking water wells (12 in Myingyan City and 6 in nearby Tha Pyay Thar Village) and 2 locations in the Ayeyarwaddy River for arsenic, boron, barium, beryllium, cadmium, cobalt, chromium, copper, fluoride, iron, mercury, manganese, molybdenum, nickel, lead, antimony, selenium, thallium, uranium, vanadium, and zinc. Concentrations of arsenic, manganese, fluoride, iron, or uranium exceeded health-based reference values in most wells. In addition, any given well usually contained more than one toxic substance at unsafe concentrations. While water testing and well sharing could reduce health risks, none of the wells sampled provide water that is entirely safe with respect to inorganic toxic substances. It is imperative that users of these wells, and users of other wells that have not been tested for multiple inorganic toxic substances throughout the region, be informed of the need for drinking water testing and the health consequences of drinking water contaminated with inorganic toxic

  15. Fabrication and characterization of cerium-doped barium titanate inverse opal by sol-gel method

    SciTech Connect

    Jin Yi; Zhu Yihua Yang Xiaoling; Li Chunzhong; Zhou Jinghong

    2007-01-15

    Cerium-doped barium titanate inverted opal was synthesized from barium acetate contained cerous acetate and tetrabutyl titanate in the interstitial spaces of a polystyrene (PS) opal. This procedure involves infiltration of precursors into the interstices of the PS opal template followed by hydrolytic polycondensation of the precursors to amorphous barium titanate and removal of the PS opal by calcination. The morphologies of opal and inverse opal were characterized by scanning electron microscope (SEM). The pores were characterized by mercury intrusion porosimetry (MIP). X-ray photoelectron spectroscopy (XPS) investigation showed the doping structure of cerium, barium and titanium. And powder X-ray diffraction allows one to observe the influence of doping degree on the grain size. The lattice parameters, crystal size and lattice strain were calculated by the Rietveld refinement method. The synthesis of cerium-doped barium titanate inverted opals provides an opportunity to electrically and optically engineer the photonic band structure and the possibility of developing tunable three-dimensional photonic crystal devices. - Graphical abstract: Cerium-doped barium titanate inverted opal was synthesized from barium acetate acid contained cerous acetate and tetrabutyl titanate in the interstitial spaces of a PS opal, which involves infiltration of precursors into the interstices of the PS opal template and removal of the PS opal by calcination.

  16. Bio-based barium alginate film: Preparation, flame retardancy and thermal degradation behavior.

    PubMed

    Liu, Yun; Zhang, Chuan-Jie; Zhao, Jin-Chao; Guo, Yi; Zhu, Ping; Wang, De-Yi

    2016-03-30

    A bio-based barium alginate film was prepared via a facile ionic exchange and casting approach. Its flammability, thermal degradation and pyrolysis behaviors, thermal degradation mechanism were studied systemically by limiting oxygen index (LOI), vertical burning (UL-94), microscale combustion calorimetry (MCC), thermogravimetric analysis (TGA) coupled with Fourier transform infrared analysis (FTIR) and pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS). It showed that barium alginate film had much higher LOI value (52.0%) than that of sodium alginate film (24.5%). Moreover, barium alginate film passed the UL-94 V-0 rating, while the sodium alginate film showed no classification. Importantly, peak of heat release rate (PHRR) of barium alginate film in MCC test was much lower than that of sodium alginate film, suggested that introduction of barium ion into alginate film significantly decreased release of combustible gases. TG-FTIR and Py-GC-MS results indicated that barium alginate produced much less flammable products than that of sodium alginate in whole thermal degradation procedure. Finally, a possible degradation mechanism of barium alginate had been proposed.

  17. Magnetic properties of Ni substituted Y-type barium ferrite

    NASA Astrophysics Data System (ADS)

    Won, Mi Hee; Kim, Chul Sung

    2014-05-01

    Y-type barium hexaferrite is attractive material for various applications, such as high frequency antennas and RF devices, because of its interesting magnetic properties. Especially, Ni substituted Y- type hexaferrites have higher magnetic ordering temperature than other Y-type. We have investigated macroscopic and microscopic properties of Y-type barium hexaferrite. Ba2Co2-xNixFe12O22 (x = 0, 0.5, 1.0, 1.5, and 2.0) samples are prepared by solid-state reaction method and studied by X-ray diffraction (XRD), vibrating sample magnetometer, and Mössbauer spectroscopy, as well as a network analyzer for high frequency characteristics. The XRD pattern is analyzed by Rietveld refinement method and confirms the hexagonal structure with R-3m. The hysteresis curve shows ferrimagnetic behavior. Saturation magnetization (Ms) decreases with Ni contents. Ni2+, which preferentially occupies the octahedral site with up-spin sub-lattice, has smaller spin value S of 1 than Co2+ having S = 3/2. The zero-field-cooled (ZFC) measurement of Ba2Co1.5Ni0.5Fe12O22 shows that Curie and spin transition temperatures are found to be 718 K and 209 K, respectively. The Curie temperature TC is increased with Ni contents, while TS is decreased with Ni. The Mössbauer spectra were measured at various temperatures and fitted by using a least-squares method with six sextet of six Lorentzian lines for Fe sites, corresponding to the 3bVI, 6cIV*, 6cVI, 18hVI, 6cIV, and 3aIV sites at below TC. From Mössbauer measurements, we confirmed the spin state of Fe ion to be Fe3+ and obtained the isomer shift (δ), magnetic hyperfine field (Hhf), and the occupancy ratio of Fe ions at six sub-lattices. The complex permeability and permittivity are measured between 100 MHz and 4 GHz, suggesting that Y-type barium hexaferrite is promising for antenna applications in UHF band.

  18. Magnetic properties of Ni substituted Y-type barium ferrite

    SciTech Connect

    Won, Mi Hee; Kim, Chul Sung

    2014-05-07

    Y-type barium hexaferrite is attractive material for various applications, such as high frequency antennas and RF devices, because of its interesting magnetic properties. Especially, Ni substituted Y- type hexaferrites have higher magnetic ordering temperature than other Y-type. We have investigated macroscopic and microscopic properties of Y-type barium hexaferrite. Ba{sub 2}Co{sub 2−x}Ni{sub x}Fe{sub 12}O{sub 22} (x = 0, 0.5, 1.0, 1.5, and 2.0) samples are prepared by solid-state reaction method and studied by X-ray diffraction (XRD), vibrating sample magnetometer, and Mössbauer spectroscopy, as well as a network analyzer for high frequency characteristics. The XRD pattern is analyzed by Rietveld refinement method and confirms the hexagonal structure with R-3m. The hysteresis curve shows ferrimagnetic behavior. Saturation magnetization (M{sub s}) decreases with Ni contents. Ni{sup 2+}, which preferentially occupies the octahedral site with up-spin sub-lattice, has smaller spin value S of 1 than Co{sup 2+} having S = 3/2. The zero-field-cooled (ZFC) measurement of Ba{sub 2}Co{sub 1.5}Ni{sub 0.5}Fe{sub 12}O{sub 22} shows that Curie and spin transition temperatures are found to be 718 K and 209 K, respectively. The Curie temperature T{sub C} is increased with Ni contents, while T{sub S} is decreased with Ni. The Mössbauer spectra were measured at various temperatures and fitted by using a least-squares method with six sextet of six Lorentzian lines for Fe sites, corresponding to the 3b{sub VI}, 6c{sub IV}*, 6c{sub VI}, 18h{sub VI}, 6c{sub IV}, and 3a{sub IV} sites at below T{sub C}. From Mössbauer measurements, we confirmed the spin state of Fe ion to be Fe{sup 3+} and obtained the isomer shift (δ), magnetic hyperfine field (H{sub hf}), and the occupancy ratio of Fe ions at six sub-lattices. The complex permeability and permittivity are measured between 100 MHz and 4 GHz, suggesting that Y-type barium hexaferrite is promising for antenna

  19. [Elimination of fluoride in urine during fluoridation of salt and drinking water].

    PubMed

    Wespi, H J; Bürgi, W

    1982-07-17

    From 552 ambulatory gynecological patients in different parts of Switzerland the urinary excretion of fluorine was measured. The patients were classified into 4 groups according to origin: (1) 84 women were from the Canton Basel-Stadt. In this city water has been fluoridated since 1962; (2) 139 women from Canton Glarus. In this area a pilot study was under way using table and baker's salt, to both of which 250 mg F/kg had been added; (3) 128 women from Canton Aargau who were using a low dose fluoridated salt (90 mg F/kg); (4) 201 patients from Cantons Aargau and Tessin respectively who were consuming neither fluoridated water or salt acted as controls. Quantitation of ionized fluorine in urine was performed by means of the fluoride ion sensitive electrode in afternoon urine samples, thus eliminating the influence of sex difference and diurnal rhythm in fluorine excretion. The molar urinary fluorine concentration was related to the corresponding urinary creatinine concentration and expressed as mumol F per mmol creatinine. The fluoridation of salt or water was considered ideal when the excretion factor amounted to 6.29 mumol X mmol-1. The most important finding was that the Glarus females excrete higher levels of fluorine than the patients from Basel, though the difference was no significant. The fluoridation of salt with 90 mg F/kg is followed by an increase of the excretion factor from 2.58 to 3.65 mumol X mmol-1. It could also be demonstrated that in Canton Glarus, where salt with higher fluorine content is used, the excretion coefficient remains below the level believed to be toxic in the long run. It is concluded that salt fluoridation with 250 gm F/kg is safe. Furthermore, the excretion of fluorine in the control group seems to confirm that fluorine is a trace element of ubiquitous occurrence even excreted in urine of individuals who deliberately avoid fluorine as an additive to table salt or water.

  20. Dietary fluoride intake from infant and toddler formulas in Poland.

    PubMed

    Opydo-Szymaczek, Justyna; Opydo, Jadwiga

    2011-08-01

    Risk of enamel fluorosis associated with excessive fluoride intake during infancy and early childhood has been widely reported in literature. Results of several studies indicate that infant formula consumption, especially in the form of powdered concentrate, may appreciably increase children's fluoride exposure in optimally fluoridated communities. The aim of the study was to measure fluoride content of infant and toddler formulas available in Poland and to discuss implications of the results. Twenty nine brands of powdered formulas were evaluated. Analyzes were performed with the use of ionselective fluoride electrode (09-37 type) and a RAE 111 chloride-silver reference electrode (MARAT). Results revealed that concentration of fluoride in all products was low (mean 29.0 μg/100 g), and that the formula itself is not a significant source of fluoride exposure. However, when reconstituted with water containing more than 0.5 ppm of fluoride, starting formulas and follow-on formulas may provide a daily fluoride intake of above the suggested threshold for fluorosis. Thus, fully formula-fed infants consuming mother milk substitutes prepared with optimally fluoridated water may be at increased risk of dental fluorosis.

  1. Arsenic from community water fluoridation: quantifying the effect.

    PubMed

    Peterson, Emily; Shapiro, Howard; Li, Ye; Minnery, John G; Copes, Ray

    2016-04-01

    Community water fluoridation is a WHO recommended strategy to prevent dental carries. One debated concern is that hydrofluorosilicic acid, used to fluoridate water, contains arsenic and poses a health risk. This study was undertaken to determine if fluoridation contributes to arsenic in drinking water, to estimate the amount of additional arsenic associated with fluoridation, and compare this to the National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard and estimates from other researchers. Using surveillance data from Ontario drinking water systems, mixed effects linear regression was performed to examine the effect of fluoridation status on the difference in arsenic concentration between raw water and treated water samples. On average, drinking water treatment was found to reduce arsenic levels in water in both fluoridated and non-fluoridated systems by 0.2 μg/L. However, fluoridated systems were associated with an additional 0.078 μg/L (95% CI 0.021, 0.136) of arsenic in water when compared to non-fluoridated systems (P = 0.008) while controlling for raw water arsenic concentrations, types of treatment processes, and source water type. Our estimate is consistent with concentrations expected from other research and is less than 10% of the NSF/ANSI standard of 1 μg/L arsenic in water. This study provides further information to inform decision-making regarding community water fluoridation.

  2. Fluoride content of clay minerals and argillaceous earth materials

    USGS Publications Warehouse

    Thomas, J.; Glass, H.D.; White, W.A.; Trandel, R.M.

    1977-01-01

    A reliable method, utilizing a fluoride ion-selective electrode, is described for the determination of fluoride in clays and shales. Interference by aluminum and iron is minimal. The reproducibility of the method is about ??5% at different levels of fluoride concentration. Data are presented for various clay minerals and for the <2-??m fractions of marine and nonmarine clays and shales. Fluoride values range from 44 ppm (0.0044%) for nontronite from Colfax, WA, to 51,800 ppm (5.18%) for hectorite from Hector, CA. In general, clays formed under hydrothermal conditions are relatively high in fluoride content, provided the hydrothermal waters are high in fluoride content. Besides hectorite, dickite from Ouray, CO, was found to contain more than 50 times as much fluoride (6700 ppm) as highly crystalline geode kaolinite (125 ppm). The clay stratum immediately overlying a fluorite mineralized zone in southern Illinois was found to have a higher fluoride content than the same stratum in a nonmineralized zone approximately 1 mile away. Nonmarine shales in contact with Australian coals were found to be lower in fluoride content than were marine shales in contact with Illinois coals. It is believed that, in certain instances, peak shifts on DTA curves of similar clay minerals are the result of significant differences in their fluoride content. ?? 1977.

  3. A comparative study of fluoride release from two different sealants

    PubMed Central

    Ananda, Shimoga-Raju

    2014-01-01

    Objectives: The introduction of fluoride releasing sealants and glass ionomer cements as fissure sealants adds another dimension to prevention of pit and fissure caries. The ability of resin sealants and glass ionomer cements to release fluoride on a long term basis to the sealed enamel and the adjacent unsealed pit and fissure and cuspal incline enamel may allow for further reduction in pit and fissure caries experience for children. Hence, the study was conducted to compare the amount of fluoride release in the plaque after placing fluoride releasing pit and fissure sealants and glass ionomer fissure sealants used in Atraumatic Restorative Treatment (ART) approach. To compare the fluoride release of both the materials at the different time intervals. Material and Methods: A total of 60 school going children were included in this study. Before application of the sealants, baseline plaque fluoride levels were estimated from all the study subjects. After application of sealants again the same was estimated at an interval of 24 hour, 9 days, 2 weeks and 4 weeks. Results: The peak plaque fluoride levels were achieved at 24 hours after application of fissure sealants in all the groups. Conclusions: Within the limitation of the study, the present study indicated that fluoride releasing fissure sealants may act as a source of fluoride in plaque which will help in preventing pit and fissure and smooth surface caries in the tooth sealed with fissure sealants. Key words:Plaque fluoride, pit and fissures sealants, dental caries. PMID:25674315

  4. Effects of different kinds of fluorides on enolase and ATPase activity of a fluoride-sensitive and fluoride-resistant Streptococcus mutans strain.

    PubMed

    van Loveren, C; Hoogenkamp, M A; Deng, D M; ten Cate, J M

    2008-01-01

    Enolase and ATPase are sensitive to fluoride. It is unclear whether this sensitivity differs for F-sensitive and F-resistant cells or for different types of fluoride. Permeabilized cells of the fluoride-sensitive strain Streptococcus mutans C180-2 and its fluoride-resistant mutant strain C180-2 FR were preincubated at pH 7 or 4 with NaF, the amine fluorides Olaflur and Dectaflur and amine chloride controls. After preincubations, enolase and ATPase activities of the cells were assessed. Enolase activity was more inhibited after preincubation at pH 7 with NaF than with Olaflur. Amine chloride stimulated, although not with statistical significance, the enolase activity of both strains. After preincubation at pH 4 the enolases were strongly inactivated, but the fluoride-resistant strain's enolase to a lesser extent. The results suggested that amine acts to protect enolase activity against the detrimental low pH effect. Gene sequencing showed that the enolase genes of the fluoride-resistant and fluoride-sensitive strain were identical. ATPase activity was not reduced after NaF preincubation at either pH 7 or pH 4. The amine fluorides and their chloride controls in the preincubation mixture reduced the ATPase activity significantly at both pH values. In conclusion, our results showed that preincubation with amine fluoride did not inhibit enolase activity more effectively than NaF. The amine part of the molecule may protect enolase activity against preincubations at low pH. ATPase activity was not inhibited by NaF preincubation but was significantly inhibited after preincubation with amine fluorides and amine chlorides.

  5. Poly(vinylidene fluoride)-based flexible and lightweight materials for attenuating microwave radiations.

    PubMed

    Sharma, Maya; Singh, Mahander Pratap; Srivastava, Chandan; Madras, Giridhar; Bose, Suryasarathi

    2014-12-10

    Two unique materials were developed, like graphene oxide (GO) sheets covalently grafted on to barium titanate (BT) nanoparticles and cobalt nanowires (Co-NWs), to attenuate the electromagnetic (EM) radiations in poly(vinylidene fluoride) (PVDF)-based composites. The rationale behind using either a ferroelectric or a ferromagnetic material in combination with intrinsically conducting nanoparticles (multiwall carbon nanotubes, CNTs), is to induce both electrical and magnetic dipoles in the system. Two key properties, namely, enhanced dielectric constant and magnetic permeability, were determined. PVDF/BT-GO composites exhibited higher dielectric constant compared to PVDF/BT and PVDF/GO composites. Co-NWs, which were synthesized by electrodeposition, exhibited saturation magnetization (Ms) of 40 emu/g and coercivity (Hc) of 300 G. Three phase hybrid composites were prepared by mixing CNTs with either BT-GO or Co-NWs in PVDF by solution blending. These nanoparticles showed high electrical conductivity and significant attenuation of EM radiations both in the X-band and in the Ku-band frequency. In addition, BT-GO/CNT and Co-NWs/CNT particles also enhanced the thermal conductivity of PVDF by ca. 8.7- and 9.3-fold in striking contrast to neat PVDF. This study open new avenues to design flexible and lightweight electromagnetic interference shielding materials by careful selection of functional nanoparticles.

  6. Effects of flossing and rinsing with a fluoridated mouthwash after brushing with a fluoridated toothpaste on salivary fluoride clearance.

    PubMed

    Duckworth, R M; Horay, C; Huntington, E; Mehta, V

    2009-01-01

    The aims of this study were to test the hypothesis that flossing after brushing with a fluoridated toothpaste may lower salivary fluoride (F), and to evaluate the consequence of subsequent F mouthwash use. Twenty adults used 3 oral hygiene regimes in a randomised order: A, brushing with an NaF toothpaste; B, as A but followed by professional flossing; C, as B followed by rinsing with an NaF mouthwash. Saliva samples were collected up to 120 min after each regime and analysed for F. The mean area under the clearance curve value for regime C was statistically significantly greater than the corresponding values for A and B (p < 0.0001), which differed little. The regime that included the mouthwash may provide better anticaries protection.

  7. Strontium and barium iodide high light yield scintillators

    NASA Astrophysics Data System (ADS)

    Cherepy, Nerine J.; Hull, Giulia; Drobshoff, Alexander D.; Payne, Stephen A.; van Loef, Edgar; Wilson, Cody M.; Shah, Kanai S.; Roy, Utpal N.; Burger, Arnold; Boatner, Lynn A.; Choong, Woon-Seng; Moses, William W.

    2008-02-01

    Europium-doped strontium and barium iodide are found to be readily growable by the Bridgman method and to produce high scintillation light yields. SrI2(Eu ) emits into the Eu2+ band, centered at 435nm, with a decay time of 1.2μs and a light yield of ˜90000photons/MeV. It offers energy resolution better than 4% full width at half maximum at 662keV, and exhibits excellent light yield proportionality. BaI2(Eu ) produces >30000photons/MeV into the Eu2+ band at 420nm (<1μs decay). An additional broad impurity-mediated recombination band is present at 550nm (>3μs decay), unless high-purity feedstock is used.

  8. Barium titanate nanocomposite capacitor FY09 year end report.

    SciTech Connect

    Stevens, Tyler E.; DiAntonio, Christopher Brian; Yang, Pin; Chavez, Tom P.; Winter, Michael R.; Monson, Todd C.; Roesler, Alexander William; Fellows, Benjamin D.

    2009-11-01

    This late start RTBF project started the development of barium titanate (BTO)/glass nanocomposite capacitors for future and emerging energy storage applications. The long term goal of this work is to decrease the size, weight, and cost of ceramic capacitors while increasing their reliability. Ceramic-based nanocomposites have the potential to yield materials with enhanced permittivity, breakdown strength (BDS), and reduced strain, which can increase the energy density of capacitors and increase their shot life. Composites of BTO in glass will limit grain growth during device fabrication (preserving nanoparticle grain size and enhanced properties), resulting in devices with improved density, permittivity, BDS, and shot life. BTO will eliminate the issues associated with Pb toxicity and volatility as well as the variation in energy storage vs. temperature of PZT based devices. During the last six months of FY09 this work focused on developing syntheses for BTO nanoparticles and firing profiles for sintering BTO/glass composite capacitors.

  9. A buffer gas cooled beam of barium monohydride

    NASA Astrophysics Data System (ADS)

    Iwata, Geoffrey; Tarallo, Marco; Zelevinsky, Tanya

    2016-05-01

    Significant advances in direct laser cooling of diatomic molecules have opened up a wide array of molecular species to precision studies spanning many-body physics, quantum collisions and ultracold dissociation. We present a cryogenic beam source of barium monohydride (BaH), and study laser ablation of solid precursor targets as well as helium buffer gas cooling dynamics. Additionally, we cover progress towards a molecular magneto-optical trap, with spectroscopic studies of relevant cooling transitions in the B2 Σ <--X2 Σ manifold in laser ablated molecules, including resolution of hyperfine structure and precision measurements of the vibrational Frank-Condon factors. Finally, we examine the feasibility of photo dissociation of trapped BaH molecules to yield optically accessible samples of ultracold hydrogen.

  10. Calcium, Strontium and Barium Homogeneous Catalysts for Fine Chemicals Synthesis.

    PubMed

    Sarazin, Yann; Carpentier, Jean-François

    2016-12-01

    The large alkaline earths (Ae), calcium, strontium and barium, have in the past 15 years yielded a brand new generation of heteroleptic molecular catalysts for the production of fine chemicals. However, the integrity of these complexes is often plagued by ligand redistribution equilibria in solution. This personal account retraces the paths followed in our research group towards the design of stable heteroleptic alkalino-earth complexes, including the use of intramolecular noncovalent Ae···H-Si and Ae···F-C interactions. Their implementation as homogenous precatalysts for reactions such as the intramolecular and intermolecular hydroamination and hydrophosphination of activated alkenes, the hydrophosphonylation of ketones, and the dehydrogenative coupling of amines and hydrosilanes that enable the efficient and controlled formations of CP, CN, or SiN σ-bonds, is presented in a synthetic perspective that highlights their overall outstanding catalytic performance.

  11. Influence of Barium Hexaferrite on Magnetic Properties of Hydroxyapatite Ceramics.

    PubMed

    Jarupoom, P; Jaita, P

    2015-11-01

    Hydroxyapatite (HA) powders was derived from natural bovine bone by sequence of thermal processes. The barium hexaferrite (BF) find magnetic powders were added into HA powders in ratio of 1-3 vol.%. The HA-BF ceramics were prepared by a solid state reaction method and sintered at 1250 degrees C for 2 h. Effects of BF additive on structural, physical and magnetic properties of HA ceramics were investigated. X-ray diffraction revealed that all HA-BF samples showed a main phase of high purity hydroxyapatite [Ca10(PO4)6(OH)2] with calcium and phosphate molar ratio of 1.67. The addition of BF into HA inhibited grain growth and caused an improvement of mechanical properties. The M-H hysteresis loops also showed an improvement in magnetic behavior for higher content of BF. Moreover, in vitro bioactivity test indicated that the 2-3 vol.% sample may be suitable for biological applications.

  12. Spectroscopic study of Er:Sm doped barium fluorotellurite glass.

    PubMed

    Bahadur, A; Dwivedi, Y; Rai, S B

    2010-09-15

    In this paper, we report the physical and spectroscopic properties of Er(3+), Sm(3+) and Er(3+):Sm(3+) ions codoped barium fluorotellurite (BFT) glasses. Different Stokes and anti-Stokes emissions were observed under 532 nm and 976 nm laser excitations. Energy transfer from Er(3+) ion to Sm(3+) ion was confirmed on the basis of luminescence intensity variation and decay curve analysis in both the cases. Under green (532 nm) excitation emission intensity of Sm(3+) ion bands improves whereas on NIR (976 nm) excitation new emission bands of Sm(3+) ions were observed in Er:Sm codoped samples. Ion interactions and the different energy transfer parameters were also calculated.

  13. Dynamics of the CRRES barium releases in the magnetosphere

    NASA Technical Reports Server (NTRS)

    Fuselier, S. A.; Mende, S. B.; Geller, S. P.; Miller, M.; Hoffman, R. A.; Wygant, J. R.; Pongratz, M.; Meredith, N. P.; Anderson, R. R.

    1994-01-01

    The Combined Release and Radiation Effects Satellite (CRRES) G-2, G-3, and G-4 ionized and neutral barium cloud positions are triangulated from ground-based optical data. From the time history of the ionized cloud motion perpendicular to the magnetic field, the late time coupling of the ionized cloud with the collisionless ambient plasma in the magnetosphere is investigated for each of the releases. The coupling of the ionized clouds with the ambient medium is quantitatively consistent with predictions from theory in that the coupling time increases with increasing distance from the Earth. Quantitative comparison with simple theory for the couping time also yields reasonable agreement. Other effects not predicted by the theory are discussed in the context of the observations.

  14. Pulsating aurora induced by upper atmospheric barium releases

    NASA Technical Reports Server (NTRS)

    Deehr, C.; Romick, G.

    1977-01-01

    The paper reports the apparent generation of pulsating aurora by explosive releases of barium vapor near 250 km altitude. This effect occurred only when the explosions were in the path of precipitating electrons associated with the visible aurora. Each explosive charge was a standard 1.5 kg thermite mixture of Ba and CuO with an excess of Ba metal which was vaporized and dispersed by the thermite explosion. Traces of Sr, Na, and Li were added to some of the charges, and monitoring was achieved by ground-based spectrophotometric observations. On March 28, 1976, an increase in emission at 5577 A and at 4278 A was observed in association with the first two bursts, these emissions pulsating with roughly a 10 sec period for approximately 60 to 100 sec after the burst.

  15. Synthesis and optical study of barium magnesium aluminate blue phosphors

    SciTech Connect

    Jeet, Suninder Pandey, O. P.; Sharma, Manoj

    2015-05-15

    Europium doped barium magnesium aluminate (BaMgAl{sub 10}O{sub 17}:Eu{sup 2+}) phosphor was prepared via solution combustion method at 550°C using urea as a fuel. Morphological and optical properties of the prepared sample was studied by X-ray diffraction (XRD), Transmission electron microscopy (TEM) and Photoluminescence spectroscopy (PL). XRD result showed the formation of pure phase BaMgAl{sub 10}O{sub 17}(JCPDS 26-0163) along with an additional phase BaAl{sub 2}O{sub 4}(JCPDS 01-082-1350). TEM image indicated the formation of faceted particles with average particle size 40 nm. From PL spectra, a broad emission band obtained at about 450 nm attributes to 4f{sup 6} 5d → 4f{sup 7} transition of Eu{sup 2+} which lies in the blue region of the visible spectrum.

  16. Impact of vanadium ions in barium borate glass.

    PubMed

    Abdelghany, A M; Hammad, Ahmed H

    2015-02-25

    Combined optical and infrared spectral measurements of prepared barium borate glasses containing different concentrations of V2O5 were carried out. Vanadium containing glasses exhibit extended UV-visible (UV/Vis.) bands when compared with base binary borate glass. UV/Vis. spectrum shows the presence of an unsymmetrical strong UV broad band centered at 214 nm attributed to the presence of unavoidable trace iron impurities within the raw materials used for the preparation of such glass. The calculated direct and indirect optical band gaps are found to decrease with increasing the vanadium content (2.9:137 for indirect and 3.99:2.01 for direct transition). This change was discussed in terms of structural changes in the glass network. Infrared absorption spectra of the glasses reveal the appearance of both triangular and tetrahedral borate units. Electron spin resonance analyses indicate the presence of unpaired species in sufficient quantity to be identified and to confirm the spectral data.

  17. Impact of vanadium ions in barium borate glass

    NASA Astrophysics Data System (ADS)

    Abdelghany, A. M.; Hammad, Ahmed H.

    2015-02-01

    Combined optical and infrared spectral measurements of prepared barium borate glasses containing different concentrations of V2O5 were carried out. Vanadium containing glasses exhibit extended UV-visible (UV/Vis.) bands when compared with base binary borate glass. UV/Vis. spectrum shows the presence of an unsymmetrical strong UV broad band centered at 214 nm attributed to the presence of unavoidable trace iron impurities within the raw materials used for the preparation of such glass. The calculated direct and indirect optical band gaps are found to decrease with increasing the vanadium content (2.9:137 for indirect and 3.99:2.01 for direct transition). This change was discussed in terms of structural changes in the glass network. Infrared absorption spectra of the glasses reveal the appearance of both triangular and tetrahedral borate units. Electron spin resonance analyses indicate the presence of unpaired species in sufficient quantity to be identified and to confirm the spectral data.

  18. Niobium and rubidium in the barium star Zeta Capricorni

    NASA Astrophysics Data System (ADS)

    Smith, V. V.; Lambert, D. L.

    1984-03-01

    An abundance analysis of the elements Rb to Nb (relative to the G-giant standard ɛ Vir) has been carried out for the barium star ζ Cap using low-noise, high-resolution Digicon and Reticon spectra. Tech's (1971) low abundance of Nb in ζ Cap suggests that the s-process ceased less than about a million years ago. The authors' improved analysis finds a higher Nb abundance consistent with the complete decay of 93Zr to 93Nb; i.e., more than 3×106 years have elapsed since the principal phase of s-processing. The abundance of Rb suggests a neutron density of N(n) ≡ 107cm-3 for the s-process site at the close of s-processing.

  19. Dielectric behavior of barium modified strontium bismuth titanate ceramic

    SciTech Connect

    Nayak, P.; Badapanda, T.; Anwar, S.; Panigrahi, S.

    2014-04-24

    Barium Modified Strontium Bismuth Titanate(SBT) ceramic with general formula Sr1−xBaxBi4Ti4O15 is prepared by solid state reaction route. The structural analysis of the ceramics was done by X-ray diffraction technique. The X-ray patterns show that all the compositions are of single phase with orthorhombic structure. The temperature dependent dielectric behavior shows that the transition temperature decreases with Ba content but the maximum dielectric constant increases. The decreases of the transition with increase in Ba{sup 2+} ion, may be due to the decrease of orthorhombicity by the incorporation of Ba{sup 2+} ion in SBT lattice.

  20. Synthesis and optical study of barium magnesium aluminate blue phosphors

    NASA Astrophysics Data System (ADS)

    Jeet, Suninder; Sharma, Manoj; Pandey, O. P.

    2015-05-01

    Europium doped barium magnesium aluminate (BaMgAl10O17:Eu2+) phosphor was prepared via solution combustion method at 550°C using urea as a fuel. Morphological and optical properties of the prepared sample was studied by X-ray diffraction (XRD), Transmission electron microscopy (TEM) and Photoluminescence spectroscopy (PL). XRD result showed the formation of pure phase BaMgAl10O17(JCPDS 26-0163) along with an additional phase BaAl2O4(JCPDS 01-082-1350). TEM image indicated the formation of faceted particles with average particle size 40 nm. From PL spectra, a broad emission band obtained at about 450 nm attributes to 4f6 5d → 4f7 transition of Eu2+ which lies in the blue region of the visible spectrum.

  1. A new type of microphone using flexoelectric barium strontium titnate

    NASA Astrophysics Data System (ADS)

    Kwon, Seol ryung; Huang, Wenbin; Zhang, Shujun; Yuan, Fuh-Gwo; Jiang, Xiaoning

    2014-03-01

    A flexoelectric bridge-structured microphone using bulk barium strontium titanate (Ba0.65Sr0.35TiO3 or BST) ceramic was investigated in this study. The flexoelectric microphone was installed in an anechoic box and exposed to the sound pressure emitted from a loud speaker. Charge sensitivity of the flexoelectric microphone was measured and calibrated using a reference microphone. The 1.5 mm×768 μm×50 μm micro-machined bridge-structured flexoelectric microphone has a sensitivity of 0.92 pC/Pa, while its resonance frequency was calculated to be 98.67 kHz. The analytical and experimental results show that the flexoelectric microphone has both high sensitivity and broad bandwidth, indicating that flexoelectric microphones are potential candidates for many applications.

  2. Preparation and magnetic properties of barium hexaferrite nanorods

    SciTech Connect

    Mu Guohong Pan Xifeng; Chen Na; Gan Keke; Gu Mingyuan

    2008-06-03

    The barium hexaferrite nanorods were successfully prepared by sol-gel technique combined with polymethylmethacrylate as template. The crystal structure, morphology and magnetic properties of BaFe{sub 12}O{sub 19} with different shape were investigated with X-ray diffraction, field emission scanning electron microscope and vibrating sample magnetometry. The results show that diameters and lengths of magnetic nanorods are about 60 nm and 300 nm, respectively. The coercivity of rod-shaped BaFe{sub 12}O{sub 19} is increased to 5350 Oe, in comparison with 4800 Oe with plate-shape. The formation mechanism of BaFe{sub 12}O{sub 19} nanorods and reasons resulting in high coercivity are discussed.

  3. BD-21 3873: another yellow-symbiotic barium star.

    NASA Astrophysics Data System (ADS)

    Smith, V. V.; Cunha, K.; Jorissen, A.; Boffin, H. M. J.

    1997-08-01

    An abundance analysis of the yellow symbiotic system BD-21 3873 reveals it to be a metal-poor K-giant ([Fe/H]=-1.3) which is enriched in the heavy s-process elements. In that respect, this star appears to be a twin of AG Dra, another yellow symbiotic system analyzed in a previous paper (Smith et al., 1996A&A...315..179S). The heavy-element abundance distributions of AG Dra and BD-21 3873 are almost identical, and are best reproduced by a s-process with a neutron exposure parameter of 1.2-1.3mb^-1^ and a neutron density logN_n_=8.3 (as derived from the Rb/Zr ratio). These two systems thus link the symbiotic stars to the binary barium and CH stars which are also s-process enriched. These binary systems, which exhibit overabundances of the heavy elements, owe their abundance peculiarities to mass transfer from thermally-pulsing asymptotic giant branch stars, which have since evolved to become white-dwarf companions of the cool stars we now view as the chemically-peculiar primaries. The spectroscopic orbits of BD-21 3873 (derived from CORAVEL measurements) and AG Dra are similar to those of barium and CH stars. With an orbital period of 281.6d, BD-21 3873 is one of the closest systems in these families, and its light curve indeed suggests that variations due to reflection and ellipticity effects are present. The amplitude of the ellipsoidal variations indicates that the giant must be close to filling its Roche lobe. However, no acceptable solution simultaneously satisfies the constraints from the light curve, the orbital elements and the evolutionary tracks in the framework of the standard Roche lobe geometry. We suggest that this discrepancy may be resolved by taking into account the deformation of the Roche lobe caused by the force driving the large mass loss of the giant.

  4. Brillouin function characteristics for La-Co substituted barium hexaferrites

    SciTech Connect

    Wu, Chuanjian E-mail: ksun@uestc.edu.cn; Yu, Zhong; Sun, Ke E-mail: ksun@uestc.edu.cn; Guo, Rongdi; Jiang, Xiaona; Lan, Zhongwen; Yang, Yan

    2015-09-14

    La-Co substituted barium hexaferrites with the chemical formula of Ba{sub 1−x}La{sub x}Fe{sub 12−x}Co{sub x}O{sub 19} (x = 0.0, 0.1, 0.3, and 0.5), prepared by a conventional ceramic method, were systematically investigated by Raman spectra, X-ray photoelectron spectroscopy, Rietveld refinement of X-ray diffraction patterns, and vibrating sample magnetometer. The result manifests that all the compounds are crystallized in magnetoplumbite hexagonal structure. Trivalent cobalt ions prevailingly occupy the 2a, 4f{sub 1}, and 12k sites. According to Néel model of collinear-spin ferrimagnetism, the molecular-field coefficients ω{sub bf2}, ω{sub kf1}, ω{sub af1}, ω{sub kf2}, and ω{sub bk} of La-Co substituted barium hexaferrites have been calculated using the nonlinear fitting method, and the magnetic moment of five sublattices (2a, 2b, 4f{sub 1}, 4f{sub 2}, and 12k) versus temperature T has been also investigated. The fitting results are coincided well with the experimental data. Moreover, with the increase of La-Co substitution amount x, the molecular-field coefficients ω{sub bf2} and ω{sub af1} decrease constantly, while the molecular-field coefficients ω{sub kf1}, ω{sub kf2}, and ω{sub bk} show a slight change.

  5. Analysis of differentially expressed genes between fluoride-sensitive and fluoride-endurable individuals in midgut of silkworm, Bombyx mori.

    PubMed

    Qian, Heying; Li, Gang; He, Qingling; Zhang, Huaguang; Xu, Anying

    2016-08-15

    Fluoride tolerance is an economically important trait of silkworm. Near-isogenic lines (NILs) of the dominant endurance to fluoride (Def) gene in Bombyx mori has been constructed before. Here, we analyzed the gene expression profiles of midgut of fluoride-sensitive and fluoride-endurable individuals of Def NILs by using high-throughput Illumina sequencing technology and bioinformatics tools, and identified differentially expressed genes between these individuals. A total of 3,612,399 and 3,567,631 clean tags for the libraries of fluoride-endurable and fluoride-sensitive individuals were obtained, which corresponded to 32,933 and 43,976 distinct clean tags, respectively. Analysis of differentially expressed genes indicates that 241 genes are differentially expressed between the two libraries. Among the 241 genes, 30 are up-regulated and 211 are down-regulated in fluoride-endurable individuals. Pathway enrichment analysis demonstrates that genes related to ribosomes, pancreatic secretion, steroid biosynthesis, glutathione metabolism, steroid biosynthesis, and glycerolipid metabolism are down-regulated in fluoride-endurable individuals. qRT-PCR was conducted to confirm the results of the DGE. The present study analyzed differential expression of related genes and tried to find out whether the crucial genes were related to fluoride detoxification which might elucidate fluoride effect and provide a new way in the fluorosis research.

  6. Fluoride ion encapsulation by Mg[superscript 2+] ions and phosphates in a fluoride riboswitch

    SciTech Connect

    Ren, Aiming; Rajashankar, Kanagalaghatta R.; Patel, Dinshaw J.

    2012-06-26

    Significant advances in our understanding of RNA architecture, folding and recognition have emerged from structure-function studies on riboswitches, non-coding RNAs whose sensing domains bind small ligands and whose adjacent expression platforms contain RNA elements involved in the control of gene regulation. We now report on the ligand-bound structure of the Thermotoga petrophila fluoride riboswitch, which adopts a higher-order RNA architecture stabilized by pseudoknot and long-range reversed Watson-Crick and Hoogsteen A {sm_bullet} U pair formation. The bound fluoride ion is encapsulated within the junctional architecture, anchored in place through direct coordination to three Mg{sup 2+} ions, which in turn are octahedrally coordinated to water molecules and five inwardly pointing backbone phosphates. Our structure of the fluoride riboswitch in the bound state shows how RNA can form a binding pocket selective for fluoride, while discriminating against larger halide ions. The T. petrophila fluoride riboswitch probably functions in gene regulation through a transcription termination mechanism.

  7. Fluoride ion encapsulation by Mg2+ ions and phosphates in a fluoride riboswitch.

    PubMed

    Ren, Aiming; Rajashankar, Kanagalaghatta R; Patel, Dinshaw J

    2012-05-13

    Significant advances in our understanding of RNA architecture, folding and recognition have emerged from structure-function studies on riboswitches, non-coding RNAs whose sensing domains bind small ligands and whose adjacent expression platforms contain RNA elements involved in the control of gene regulation. We now report on the ligand-bound structure of the Thermotoga petrophila fluoride riboswitch, which adopts a higher-order RNA architecture stabilized by pseudoknot and long-range reversed Watson-Crick and Hoogsteen A•U pair formation. The bound fluoride ion is encapsulated within the junctional architecture, anchored in place through direct coordination to three Mg(2+) ions, which in turn are octahedrally coordinated to water molecules and five inwardly pointing backbone phosphates. Our structure of the fluoride riboswitch in the bound state shows how RNA can form a binding pocket selective for fluoride, while discriminating against larger halide ions. The T. petrophila fluoride riboswitch probably functions in gene regulation through a transcription termination mechanism.

  8. Method for decontamination of nickel-fluoride-coated nickel containing actinide-metal fluorides

    DOEpatents

    Windt, Norman F.; Williams, Joe L.

    1983-01-01

    The invention is a process for decontaminating particulate nickel contaminated with actinide-metal fluorides. In one aspect, the invention comprises contacting nickel-fluoride-coated nickel with gaseous ammonia at a temperature effecting nickel-catalyzed dissociation thereof and effecting hydrogen-reduction of the nickel fluoride. The resulting nickel is heated to form a melt and a slag and to effect transfer of actinide metals from the melt into the slag. The melt and slag are then separated. In another aspect, nickel containing nickel oxide and actinide metals is contacted with ammonia at a temperature effecting nickel-catalyzed dissociation to effect conversion of the nickel oxide to the metal. The resulting nickel is then melted and separated as described. In another aspect nickel-fluoride-coated nickel containing actinide-metal fluorides is contacted with both steam and ammonia. The resulting nickel then is melted and separated as described. The invention is characterized by higher nickel recovery, efficient use of ammonia, a substantial decrease in slag formation and fuming, and a valuable increase in the service life of the furnace liners used for melting.

  9. Influences of charcoal and bamboo charcoal amendment on soil-fluoride fractions and bioaccumulation of fluoride in tea plants.

    PubMed

    Gao, Hongjian; Zhang, Zhengzhu; Wan, Xiaochun

    2012-10-01

    High levels of fluoride in tea plants pose a potential health risk to humans who drink tea. It has been demonstrated that tea plant fluoride is closely related to the available fluoride in soil. But approaches that could be used to regulate the availability of fluoride in soil have been rarely seen. This study aims to investigate how the addition of charcoal and bamboo charcoal affected soil fluoride availability and bioaccumulation of fluoride in tea plants. In a microcosm experiment, tea plants were grown in the tea garden soil mixed with different amounts of charcoal and bamboo charcoal [that is, 0.5, 1.0, 2.5, and 5.0 % (w/w)]. Soil-fluoride fractions and fluoride accumulated in tea plants were determined using the sequential extraction and ion selective electrode method. Obtained results showed that both charcoal and bamboo charcoal additions significantly enhanced the concentrations of Fe/Mn oxide-bound fluoride, but significantly reduced the concentrations of water-soluble and exchangeable fluoride (p < 0.05) in soil. Charcoal and bamboo charcoal additions also significantly decreased the amounts of fluoride in tea roots and tea leaves (p < 0.05). However, the additions of charcoal and bamboo charcoal had no impacts on the tea quality, as indexed by the concentrations of polysaccharides, polyphenols, amino acids, and caffeine in tea leaves. These results suggested that application of charcoal and bamboo charcoal may provide a useful method to reduce the availability of fluoride in soil and the subsequent fluoride uptake by tea plants.

  10. Production of sintered porous metal fluoride pellets

    DOEpatents

    Anderson, L.W.; Stephenson, M.J.

    1973-12-25

    Porous pellets characterized by a moderately reactive crust and a softer core of higher reactivity are produced by forming agglomerates containing a metal fluoride powder and a selected amount ofwater. The metal fluoride is selected to be sinterable and essentially non-reactive with gaseous fluorinating agents. The agglomerates are contacted with a gaseous fluorinating agent under controlled conditions whereby the heat generated by localized reaction of the agent and water is limited to values effccting bonding by localized sintering. Porous pellets composed of cryolite (Na/sub 3/AlF/sub 6/) can be used to selectively remove trace quantities of niobium pentafluoride from a feed gas consisting predominantly of uranium hexafluoride. (Official Gazette)

  11. Necessity to review the Brazilian regulation about fluoride toothpastes

    PubMed Central

    Cury, Jaime Aparecido; Caldarelli, Pablo Guilherme; Tenuta, Livia Maria Andaló

    2015-01-01

    The aim of this study was to evaluate the adequacy of the Brazilian legislation about fluoride toothpaste. A search was conducted in LILACS, Medline and SciELO databases about the fluoride concentration found in Brazilians toothpastes, using descriptors on health. Publications since 1981 have shown that some Brazilian toothpastes are not able to maintain, during their expiration time, a minimum of 1,000 ppm F of soluble fluoride in the formulation. However, the Brazilian regulation (ANVISA, Resolution 79, August 28, 2000) only sets the maximum total fluoride (0.15%; 1,500 ppm F) that a toothpaste may contain but not the minimum concentration of soluble fluoride that it should contain to have anticaries potential, which according to systematic reviews should be 1,000 ppm F. Therefore, the Brazilian regulation on fluoride toothpastes needs to be revised to assure the efficacy of those products for caries control. PMID:26487295

  12. Risk assessment of fluoride exposure in drinking water of Tunisia.

    PubMed

    Guissouma, Wiem; Hakami, Othman; Al-Rajab, Abdul Jabbar; Tarhouni, Jamila

    2017-03-03

    The presence of fluoride in drinking water is known to reduce dental cavities among consumers, but an excessive intake of this anion might leads to dental and skeletal fluorosis. This study reports a complete survey of the fluoridated tap water taken from 100 water consumption points in Tunisia. The fluoride concentrations in tap water were between 0 and 2.4 mg L(-1). Risk assessment of Fluoride exposure was assessed depending on the age of consumers using a four-step method: hazard identification, toxicity reference values selection (TRVs), daily exposure assessment, and risk characterization. Our findings suggest that approximately 75% of the Tunisian population is at risk for dental decay, 25% have a potential dental fluorosis risk, and 20% might have a skeletal fluorosis risk according to the limits of fluoride in drinking water recommended by WHO. More investigations are recommended to assess the exposure risk of fluoride in other sources of drinking water such as bottled water.

  13. Distribution of fluoride in ground water of West Virginia

    USGS Publications Warehouse

    Mathes, M.V.; Waldron, M.C.

    1993-01-01

    This report describes the results of a study by the U.S. Geological Survey, in cooperation with the West Virginia Geological and Economic Survey, to evaluate the distribution of fluoride in ground water of West Virginia. Fluoride is a natural chemical constituent in domestic and public water supplies in West Virginia. Fluoride concentrations of about 1.0 milligram per liter in drinking water are beneficial to dental health. Concentrations greater than 2.0 milligrams per liter, however, could harm teeth and bones. Fluoride concentra- tions in ground water of West Virginia range from less than 0.1 to 12 milligrams per liter. Fluoride concentrations that exceed 2.0 milligrams per liter are found in wells drilled to all depths, wells drilled in all topographic settings, and wells drilled into most geologic units. Most fluoride concentrations that exceed 2.0 milligrams per liter are located at sites clustered in the northwestern part of the State.

  14. Necessity to review the Brazilian regulation about fluoride toothpastes.

    PubMed

    Cury, Jaime Aparecido; Caldarelli, Pablo Guilherme; Tenuta, Livia Maria Andaló

    2015-01-01

    The aim of this study was to evaluate the adequacy of the Brazilian legislation about fluoride toothpaste. A search was conducted in LILACS, Medline and SciELO databases about the fluoride concentration found in Brazilians toothpastes, using descriptors on health. Publications since 1981 have shown that some Brazilian toothpastes are not able to maintain, during their expiration time, a minimum of 1,000 ppm F of soluble fluoride in the formulation. However, the Brazilian regulation (ANVISA, Resolution 79, August 28, 2000) only sets the maximum total fluoride (0.15%; 1,500 ppm F) that a toothpaste may contain but not the minimum concentration of soluble fluoride that it should contain to have anticaries potential, which according to systematic reviews should be 1,000 ppm F. Therefore, the Brazilian regulation on fluoride toothpastes needs to be revised to assure the efficacy of those products for caries control.

  15. Numberical simulation of the effects of radially injected barium plasma in the ionosphere

    NASA Technical Reports Server (NTRS)

    Swift, D. W.

    1985-01-01

    The morphology of the ion cloud in the radial shaped charge barium injection was studied. The shape of the ion cloud that remains after the explosive products and neutral barium clears away was examined. The ion cloud which has the configuration of a rimless wagon wheel is shown. The major features are the 2.5 km radius black hole in the center of the cloud, the surrounding ring of barium ion and the spokes of barium ionization radiating away from the center. The cloud shows no evolution after it emerges from the neutral debris and it is concluded that it is formed within 5 seconds of the event. A numerical model is used to calculate the motion of ions and electrons subject to the electrostatic and lorenz forces.

  16. Severe acute cholangitis after endoscopic sphincterotomy induced by barium examination: A case report.

    PubMed

    Zhang, Zhen-Hai; Wu, Ya-Guang; Qin, Cheng-Kun; Su, Zhong-Xue; Xu, Jian; Xian, Guo-Zhe; Wu, Shuo-Dong

    2012-10-21

    Endoscopic sphincterotomy (EST) is considered as a possible etiological factor for severe cholangitis. We herein report a case of severe cholangitis after endoscopic sphincterotomy induced by barium examination. An adult male patient presented with epigastric pain was diagnosed as having choledocholithiasis by ultrasonography. EST was performed and the stone was completely cleaned. Barium examination was done 3 d after EST and severe cholangitis appeared 4 h later. The patient was recovered after treated with tienam for 4 d. Barium examination may induce severe cholangitis in patients after EST, although rare, barium examination should be chosen cautiously. Cautions should be also used when EST is performed in patients younger than 50 years to avoid the damage to the sphincter of Oddi.

  17. 21 CFR 201.304 - Tannic acid and barium enema preparations.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... added to barium enemas to improve X-ray pictures. Tannic acid is capable of causing diminished liver... use in enemas. Tannic acid for rectal use to enhance X-ray visualization is regarded as a new...

  18. 21 CFR 201.304 - Tannic acid and barium enema preparations.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... added to barium enemas to improve X-ray pictures. Tannic acid is capable of causing diminished liver... use in enemas. Tannic acid for rectal use to enhance X-ray visualization is regarded as a new...

  19. 21 CFR 201.304 - Tannic acid and barium enema preparations.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... added to barium enemas to improve X-ray pictures. Tannic acid is capable of causing diminished liver... use in enemas. Tannic acid for rectal use to enhance X-ray visualization is regarded as a new...

  20. 21 CFR 201.304 - Tannic acid and barium enema preparations.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... added to barium enemas to improve X-ray pictures. Tannic acid is capable of causing diminished liver... use in enemas. Tannic acid for rectal use to enhance X-ray visualization is regarded as a new...

  1. 21 CFR 201.304 - Tannic acid and barium enema preparations.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... added to barium enemas to improve X-ray pictures. Tannic acid is capable of causing diminished liver... use in enemas. Tannic acid for rectal use to enhance X-ray visualization is regarded as a new...

  2. Comparison of flow-controlled calcium and barium carbonate precipitation patterns

    NASA Astrophysics Data System (ADS)

    Schuszter, G.; De Wit, A.

    2016-12-01

    Various precipitation patterns can be obtained in flow conditions when injecting a solution of sodium carbonate in a confined geometry initially filled with a solution of either barium or calcium chloride. We compare here the barium and calcium carbonate precipitate structures as a function of initial concentrations and injection flow rate. We show that, in some part of the parameter space, the patterns are similar and feature comparable properties indicating that barium and calcium behave similarly in the related flow-controlled precipitation conditions. For other values of parameters though, the precipitate structures are different indicating that the cohesive and microscopic properties of barium versus calcium carbonate are then important in shaping the pattern in flow conditions.

  3. 75 FR 36629 - Barium Chloride From the People's Republic of China: Continuation of Antidumping Duty Order

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-28

    ... China: Final Results of Expedited Third Sunset Review of Antidumping Duty Order, 74 FR 55814 (October 29... the order is barium chloride, a chemical compound having the formulas BaCl 2 or BaCl 2 - 2H 2...

  4. Bone scintigraphy in fluoride treated osteoporosis

    SciTech Connect

    Froelich, J.W.; Kleerekoper, M.; Parker, D.A.

    1985-05-01

    Quantitative bone scintigraphy was performed on 23 white females with post-menopausal osteoporosis and vertebral compression fractures. These patients were then entered into a randomized, double-blind clinical trial or sodium fluoride therapy (NaF=14, placebo=9) which included repeat bone scintigraphy every six months. Scintigraphic images were acquired for 500K counts per image over the total body with computer acquisition over the posterior thoracic and lumbar spine. Images were obtained on a wide field-of-view gamma camera two hours after injecting 15 mCi of Tc-99m MDP. Data analysis showed a significant reduction in the activity ratio of abnormal vertebral body to normal vertebral body in those patients treated with sodium fluoride (paired t-test p=0.0095). No significant change was observed in the control group of (p=0.142). These results suggest that sodium fluoride therapy promotes more rapid healing of osteoporotic vertebral fractures. They also demonstrate the utility of serial quantitative bone scintigraphy in assessing osteoporotic patients with vertebral compression fractures.

  5. Effects of a documented hydrogen fluoride leak

    SciTech Connect

    Feder, W.A.

    1985-01-01

    At about 6 a.m. on June 19, 1984, 1037 liters of pressurized HF liquid escaped from a storage tank through a 2 mm diameter hole. 48 hours after the leak was discovered and sealed, visible injury to vegetation was observed 2 miles downwind of the source in a tear drop pattern. Injury symptoms ranged from a slight browning of leaves and needles to death of twigs and leaves and needles. Poplar, white pine, spruce, oak, red maple and several herbaceous plant species were injured. Ragweed was not injured but sensitive fern was severely injured. Goldenrod was also injured but recovered within 3 weeks after exposure. White pine trees within 1/4 of a mile from the source were killed. Fluoride analysis of tissues from upwind and downwind trees and herbaceous plants revealed fluoride tissue levels ranging from 5 to 34,000 ppm. Examples of distance/concentration are given. Soils revealed fluoride levels of about 1 ppm at all locations.

  6. Uranyl fluoride luminescence in acidic aqueous solutions

    SciTech Connect

    Beitz, J.V.; Williams, C.W.

    1996-08-01

    Luminescence emission spectra and decay rates are reported for uranyl species in acidic aqueous solutions containing HF or added NaF. The longest luminescence lifetime, 0.269 {+-} 0.006 ms, was observed from uranyl in 1 M HF + 1 M HClO{sub 4} at 296 K and decreased with increasing temperature. Based on a luminescence dynamics model that assumes equilibrium among electronically excited uranyl fluoride species and free fluoride ion, this long lived uranyl luminescence in aqueous solution is attributed primarily to UO{sub 2}F{sub 2}. Studies on the effect of added LiNO{sub 3} or Na{sub 2}WO{sub 4}{center_dot}2H{sub 2}O showed relatively weak quenching of uranyl fluoride luminescence which suggests that high sensitivity determination of the UF{sub 6} content of WF{sub 6} gas should be feasible via uranyl luminescence analysis of hydrolyzed gas samples of impure WF{sub 6}.

  7. 40 CFR 60.202 - Standard for fluorides.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 6 2011-07-01 2011-07-01 false Standard for fluorides. 60.202 Section... Industry: Wet-Process Phosphoric Acid Plants § 60.202 Standard for fluorides. (a) On and after the date on... facility any gases which contain total fluorides in excess of 10.0 g/Mg of equivalent P2O5 feed (0.020...

  8. 40 CFR 60.202 - Standard for fluorides.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for fluorides. 60.202 Section... Industry: Wet-Process Phosphoric Acid Plants § 60.202 Standard for fluorides. (a) On and after the date on... facility any gases which contain total fluorides in excess of 10.0 g/Mg of equivalent P2O5 feed (0.020...

  9. Fluoride use in caries prevention in the primary care setting.

    PubMed

    Clark, Melinda B; Slayton, Rebecca L

    2014-09-01

    Dental caries remains the most common chronic disease of childhood in the United States. Caries is a largely preventable condition, and fluoride has proven effectiveness in the prevention of caries. The goals of this clinical report are to clarify the use of available fluoride modalities for caries prevention in the primary care setting and to assist pediatricians in using fluoride to achieve maximum protection against dental caries while minimizing the likelihood of enamel fluorosis.

  10. Inhibition of dentin demineralization by fluoride in vitro.

    PubMed

    ten Cate, J M; Damen, J J; Buijs, M J

    1998-01-01

    Compared with the knowledge accumulated on enamel-fluoride interactions, relatively little data is available regarding fluoride effects on dentin. This applies to both laboratory and clinical studies into the efficacy of fluoride schemes for the prevention of root surface caries. This study aimed to determine the effects of fluoride and pH on the demineralization of dentin, such as to provide information necessary to develop preventive programmes. Bovine dentin blocks were subjected to undersaturated calcium- and phosphate-containing solutions in the pH range 4.0-6.0 with fluoride added at concentrations between 0.5 and 10 ppm. Non-fluoride solutions served as controls. Mineral loss was assessed chemically and by transversal microradiography. Comparisons were made with similar studies on enamel demineralization. The results showed that demineralization of dentin depends on both pH and fluoride concentration in the demineralizing solution. Inhibition of demineralization that could be relevant from a clinical point of view was found at fluoride values 5-10 times the corresponding values for enamel. Also rapid depletion of fluoride from the solutions was observed, indicating the high uptake capacity of dentin for fluoride. Lesion depth depended on pH of the solution while the fluoride levels were associated with the surface layer, both in mineral content and depth. For dentin we propose a demineralization mechanism where acid penetrates rapidly into the tissue, presumably through the tubules, after which the released calcium and phosphate is partly trapped by the inward diffusing fluoride. This leads to the formation of a surface layer, which may even be hypermineralized compared to sound dentin.

  11. Kubelka-Munk optical properties of a barium sulfate white reflectance standard.

    PubMed

    Patterson, E M; Shelden, C E; Stockton, B H

    1977-03-01

    We have measured the Kubelka-Munk scattering and absorption coefficients for a barium sulfate white reflectance standard. These measurements have been based on measurements of the absolute reflectance for the particular barium sulfate samples whose scattering and absorption coefficients were measured. This method gives results that are different from earlier measurements; the differences are significant for measurements of the optical properties of atmospheric aerosols.

  12. Role of Barium Swallow in Diagnosing Clinically Significant Anastomotic Leak following Esophagectomy

    PubMed Central

    Roh, Simon; Iannettoni, Mark D.; Keech, John C.; Bashir, Mohammad; Gruber, Peter J.; Parekh, Kalpaj R.

    2016-01-01

    Background Barium swallow is performed following esophagectomy to evaluate the anastomosis for detection of leaks and to assess the emptying of the gastric conduit. The aim of this study was to evaluate the reliability of the barium swallow study in diagnosing anastomotic leaks following esophagectomy. Methods Patients who underwent esophagectomy from January 2000 to December 2013 at our institution were investigated. Barium swallow was routinely done between days 5–7 to detect a leak. These results were compared to clinically determined leaks (defined by neck wound infection requiring jejunal feeds and or parenteral nutrition) during the postoperative period. The sensitivity and specificity of barium swallow in diagnosing clinically significant anastomotic leaks was determined. Results A total of 395 esophagectomies were performed (mean age, 62.2 years). The indications for the esophagectomy were as follows: malignancy (n=320), high-grade dysplasia (n=14), perforation (n=27), benign stricture (n=7), achalasia (n=16), and other (n=11). A variety of techniques were used including transhiatal (n=351), McKeown (n=35), and Ivor Lewis (n=9) esophagectomies. Operative mortality was 2.8% (n=11). Three hundred and sixty-eight patients (93%) underwent barium swallow study after esophagectomy. Clinically significant anastomotic leak was identified in 36 patients (9.8%). Barium swallow was able to detect only 13/36 clinically significant leaks. The sensitivity of the swallow in diagnosing a leak was 36% and specificity was 97%. The positive and negative predictive values of barium swallow study in detecting leaks were 59% and 93%, respectively. Conclusion Barium swallow is an insensitive but specific test for detecting leaks at the cervical anastomotic site after esophagectomy. PMID:27066433

  13. Elevated Z line: a new sign of Barrett's esophagus on double-contrast barium esophagograms.

    PubMed

    Levine, Marc S; Ahmad, Nuzhat A; Rubesin, Stephen E

    2015-01-01

    We describe an elevated Z line as a new radiographic sign of Barrett's esophagus characterized by a transversely oriented, zigzagging, barium-etched line extending completely across the circumference of the midesophagus. An elevated Z line is rarely seen in other patients, so this finding should be highly suggestive of Barrett's esophagus on double-contrast barium esophagograms. If the patient is a potential candidate for surveillance, endoscopy and biopsy should be performed to confirm the presence of Barrett's esophagus.

  14. Comparison of the reflectance characteristics of polytetrafluoroethylene and barium sulfate paints

    NASA Technical Reports Server (NTRS)

    Butner, C. L.; Schutt, J. B.; Shai, M. C.

    1984-01-01

    Preliminary results are presented of the directional reflectance measurements taken on two tetrafluorethylene (TFE) paints formulated with silicone binders. Both paints are found to be more Lambertian than barium sulfate paint and pressed powder, although the pigment to binder ratios for barium sulfate and TFE paints are about 133 and 3.3 to 1, respectively. The TFE paints exhibit total visible reflectances above 90 percent and offer surfaces that are not significantly affected by water.

  15. Calculations of energy levels and lifetimes of low-lying states of barium and radium

    SciTech Connect

    Dzuba, V. A.; Ginges, J. S. M.

    2006-03-15

    We use the configuration-interaction method and many-body perturbation theory to perform accurate calculations of energy levels, transition amplitudes, and lifetimes of low-lying states of barium and radium. Calculations for radium are needed for the planning of measurements of parity- and time-invariance-violating effects which are strongly enhanced in this atom. Calculations for barium are used to control the accuracy of the calculations.

  16. Barium isotopes in Allende meteorite - Evidence against an extinct superheavy element

    NASA Technical Reports Server (NTRS)

    Lewis, R. S.; Anders, E.; Shimamura, T.; Lugmair, G. W.

    1983-01-01

    Carbon and chromite fractions from the Allende meteorite that contain isotopically anomalous xenon-131 to xenon-136 (carbonaceous chondrite fission or CCF xenon) at up to 5 x 10 to the 11th atoms per gram show no detectable isotopic anomalies in barium-130 to barium-138. This rules out the possibility that the CCF xenon was formed by in situ fission of an extinct superheavy element. Apparently the CCF xenon and its carbonaceous carrier are relics from stellar nucleosynthesis.

  17. Reviews of the environmental effects of pollutants. IX. Fluoride

    SciTech Connect

    Drury, J.S.; Ensminger, J.T.; Hammons, A.S.; Holleman, J.W.; Lewis, E.B.; Preston, E.L.; Shriner, C.R.; Towill, L.E.

    1980-09-01

    This study is a comprehensive, multidisciplinary review of the health and environmental effects of fluoride on microorganisms, plants, wild and domestic animals, and humans. More than 1000 references are cited. Human intake of fluoride is chiefly through the diet; drinking water is normally the largest single source. Low concentrations of fluoride in water (approximately 1 ppM) benefit mammalian systems, making bone and tooth apatite less soluble, but long-term ingestion of water containing more than 8 ppM fluoride causes fluorosis in humans. Fluoride salts are lethal to humans when ingested in doses of about 3 g or more. At concentrations normally encountered by the general public, fluoride is not teratogenic, mutagenic, or carcinogenic to humans, but chronic fluoride toxicosis of both livestock and wildlife is an important problem in many areas of the United States. The principal manifestations of chronic fluoride toxicosis in livestock are dental fluorosis, osteofluorosis, lameness, and impaired performance. Among domestic animals, dairy cattle are the most sensitive to excessive fluoride exposure.

  18. Cochrane reviews on the benefits/risks of fluoride toothpastes.

    PubMed

    Wong, M C M; Clarkson, J; Glenny, A-M; Lo, E C M; Marinho, V C C; Tsang, B W K; Walsh, T; Worthington, H V

    2011-05-01

    This concise review presents two Cochrane Reviews undertaken to determine: (1) the relative effectiveness of fluoride toothpastes of different concentrations in preventing dental caries in children and adolescents; and (2) the relationship between the use of topical fluorides in young children and their risk of developing dental fluorosis. To determine the relative effectiveness of fluoride toothpastes of different concentrations, we undertook a network meta-analysis utilizing both direct and indirect comparisons from randomized controlled trials (RCTs). The review examining fluorosis included evidence from experimental and observational studies. The findings of the reviews confirm the benefits of using fluoride toothpaste, when compared with placebo, in preventing caries in children and adolescents, but only significantly for fluoride concentrations of 1000 ppm and above. The relative caries-preventive effects of fluoride toothpastes of different concentrations increase with higher fluoride concentration. However, there is weak, unreliable evidence that starting the use of fluoride toothpaste in children under 12 months of age may be associated with an increased risk of fluorosis. The decision of what fluoride levels to use for children under 6 years should be balanced between the risk of developing dental caries and that of mild fluorosis.

  19. Effects of oral doses of fluoride on nestling European starlings

    USGS Publications Warehouse

    Fleming, W.J.; Grue, C.E.; Schuler, C.A.; Bunck, C.M.

    1987-01-01

    Nestling European starlings (Sturnus vulgaris), raised and fed by free-living adults, were given daily oral doses of either distilled water, 193 mg sodium as Na2CO3 per kg of body weight (sodium control group), or 6, 10, 13, 17,23, 30, 40, 80, 160 mg of the fluoride ion as NaF in distilled water per kg of body weight (mg/kg). Dosing began when nestlings were 24-48 hr old and continued for 16 days. The 24-hr LD50 of fluoride for day-old starlings was 50 mg/kg. The 16-day LD50 was 17 mg/kg. The sodium control group did not differ from the water control group with respect to any of the measured variables. Growth rates were significantly reduced in the 13 and 17 mg of fluoride/kg groups; weights of birds given higher dose levels were omitted from growth comparisons because of high, fluoride-induced mortality. Although pre-fledging weights for the 10, 13, and 17 mg of fluoride/kg groups averaged 3.6 to 8.6% less than controls at 17 days, this difference was not significant. Feather and bone growth of the fluoride and control groups were not different, except for keel length measured at 17 days of age which averaged less in the fluoride groups. Liver and spleen weights were not affected by fluoride treatments. No histological damage related to fluoride treatments was found in liver, spleen, or kidney. The logarithm of bone fluoride and magnesium concentration increased with the logarithm of increasing fluoride treatment levels and were significantly correlated with each other. Fluoride treatments had no effect on percent calcium or phosphorus in bone or plasma alkaline phosphatase activity. Oral doses of fluoride appear to be more toxic than equivalent dietary levels. Most birds probably acquire fluoride through their diet. Therefore, the results of the study may overestimate the potential effects of fluorides on songbirds living in fluoride-contaminated environments.

  20. Novel fluorogenic probe for fluoride ion based on the fluoride-induced cleavage of tert-butyldimethylsilyl ether

    NASA Astrophysics Data System (ADS)

    Yang, Xiao-Feng

    2007-06-01

    A highly sensitive and selective fluorogenic probe for fluoride ion, 4-methylumbelliferyl tert-butyldimethylsilyl ether (4-MUTBS), was designed and synthesized. 4-MUTBS was a weakly fluorescent compound and was synthesized via the one-step reaction of 4-MU with tert-butyldimethylsilyl chloride. Upon incubation with fluoride ion in acetone-water solution (7:3, v/v), the Si-O bond of 4-MUTBS was cleaved and highly fluorescent 4-methylumbelliferone (4-MU) was released, hence leading to the fluorescence increase of the reaction solution. The fluorescence increase is linearly with fluoride concentration in the range 50-8000 nmol l -1 with a detection limit of 19 nmol l -1 (3 σ). Because of the high affinity of silicon toward fluoride ion, the proposed probe shows excellent selectivity toward fluoride ion over other anions. The method has been successfully applied to the fluoride determination in toothpaste and tap water samples.

  1. Examination of Liquid Fluoride Salt Heat Transfer

    SciTech Connect

    Yoder Jr, Graydon L

    2014-01-01

    The need for high efficiency power conversion and energy transport systems is increasing as world energy use continues to increase, petroleum supplies decrease, and global warming concerns become more prevalent. There are few heat transport fluids capable of operating above about 600oC that do not require operation at extremely high pressures. Liquid fluoride salts are an exception to that limitation. Fluoride salts have very high boiling points, can operate at high temperatures and low pressures and have very good heat transfer properties. They have been proposed as coolants for next generation fission reactor systems, as coolants for fusion reactor blankets, and as thermal storage media for solar power systems. In each case, these salts are used to either extract or deliver heat through heat exchange equipment, and in order to design this equipment, liquid salt heat transfer must be predicted. This paper discusses the heat transfer characteristics of liquid fluoride salts. Historically, heat transfer in fluoride salts has been assumed to be consistent with that of conventional fluids (air, water, etc.), and correlations used for predicting heat transfer performance of all fluoride salts have been the same or similar to those used for water conventional fluids an, water, etc). A review of existing liquid salt heat transfer data is presented, summarized, and evaluated on a consistent basis. Less than 10 experimental data sets have been found in the literature, with varying degrees of experimental detail and measured parameters provided. The data has been digitized and a limited database has been assembled and compared to existing heat transfer correlations. Results vary as well, with some data sets following traditional correlations; in others the comparisons are less conclusive. This is especially the case for less common salt/materials combinations, and suggests that additional heat transfer data may be needed when using specific salt eutectics in heat transfer

  2. Comparison of Calcium and Barium Microcapsules as Scaffolds in the Development of Artificial Dermal Papillae

    PubMed Central

    Liu, Yang; Lin, Changmin; Zeng, Yang; Li, Haihong; Cai, Bozhi; Huang, Keng; Yuan, Yanping; Li, Yu

    2016-01-01

    This study aimed to develop and evaluate barium and calcium microcapsules as candidates for scaffolding in artificial dermal papilla. Dermal papilla cells (DPCs) were isolated and cultured by one-step collagenase treatment. The DPC-Ba and DPC-Ca microcapsules were prepared by using a specially designed, high-voltage, electric-field droplet generator. Selected microcapsules were assessed for long-term inductive properties with xenotransplantation into Sprague-Dawley rat ears. Both barium and calcium microcapsules maintained xenogenic dermal papilla cells in an immunoisolated environment and induced the formation of hair follicle structures. Calcium microcapsules showed better biocompatibility, permeability, and cell viability in comparison with barium microcapsules. Before 18 weeks, calcium microcapsules gathered together, with no substantial immune response. After 32 weeks, some microcapsules were near inflammatory cells and wrapped with fiber. A few large hair follicles were found. Control samples showed no marked changes at the implantation site. Barium microcapsules were superior to calcium microcapsules in structural and mechanical stability. The cells encapsulated in hydrogel barium microcapsules exhibited higher short-term viability. This study established a model to culture DPCs in 3D culture conditions. Barium microcapsules may be useful in short-term transplantation study. Calcium microcapsules may provide an effective scaffold for the development of artificial dermal papilla. PMID:27123456

  3. Comparison of Calcium and Barium Microcapsules as Scaffolds in the Development of Artificial Dermal Papillae.

    PubMed

    Liu, Yang; Lin, Changmin; Zeng, Yang; Li, Haihong; Cai, Bozhi; Huang, Keng; Yuan, Yanping; Li, Yu

    2016-01-01

    This study aimed to develop and evaluate barium and calcium microcapsules as candidates for scaffolding in artificial dermal papilla. Dermal papilla cells (DPCs) were isolated and cultured by one-step collagenase treatment. The DPC-Ba and DPC-Ca microcapsules were prepared by using a specially designed, high-voltage, electric-field droplet generator. Selected microcapsules were assessed for long-term inductive properties with xenotransplantation into Sprague-Dawley rat ears. Both barium and calcium microcapsules maintained xenogenic dermal papilla cells in an immunoisolated environment and induced the formation of hair follicle structures. Calcium microcapsules showed better biocompatibility, permeability, and cell viability in comparison with barium microcapsules. Before 18 weeks, calcium microcapsules gathered together, with no substantial immune response. After 32 weeks, some microcapsules were near inflammatory cells and wrapped with fiber. A few large hair follicles were found. Control samples showed no marked changes at the implantation site. Barium microcapsules were superior to calcium microcapsules in structural and mechanical stability. The cells encapsulated in hydrogel barium microcapsules exhibited higher short-term viability. This study established a model to culture DPCs in 3D culture conditions. Barium microcapsules may be useful in short-term transplantation study. Calcium microcapsules may provide an effective scaffold for the development of artificial dermal papilla.

  4. Barium swallow study in routine clinical practice: a prospective study in patients with chronic cough*,**

    PubMed Central

    Nin, Carlos Shuler; Marchiori, Edson; Irion, Klaus Loureiro; Paludo, Artur de Oliveira; Alves, Giordano Rafael Tronco; Hochhegger, Daniela Reis; Hochhegger, Bruno

    2013-01-01

    OBJECTIVE: To assess the routine use of barium swallow study in patients with chronic cough. METHODS: Between October of 2011 and March of 2012, 95 consecutive patients submitted to chest X-ray due to chronic cough (duration > 8 weeks) were included in the study. For study purposes, additional images were obtained immediately after the oral administration of 5 mL of a 5% barium sulfate suspension. Two radiologists systematically evaluated all of the images in order to identify any pathological changes. Fisher's exact test and the chi-square test for categorical data were used in the comparisons. RESULTS: The images taken immediately after barium swallow revealed significant pathological conditions that were potentially related to chronic cough in 12 (12.6%) of the 95 patients. These conditions, which included diaphragmatic hiatal hernia, esophageal neoplasm, achalasia, esophageal diverticulum, and abnormal esophageal dilatation, were not detected on the images taken without contrast. After appropriate treatment, the symptoms disappeared in 11 (91.6%) of the patients, whereas the treatment was ineffective in 1 (8.4%). We observed no complications related to barium swallow, such as contrast aspiration. CONCLUSIONS: Barium swallow improved the detection of significant radiographic findings related to chronic cough in 11.5% of patients. These initial findings suggest that the routine use of barium swallow can significantly increase the sensitivity of chest X-rays in the detection of chronic cough-related etiologies. PMID:24473762

  5. Thermal conversions of the yttrium-barium-copper salt of carboxylated cellulose and the synthesis of yttrium barium cuprate from it

    SciTech Connect

    Kaputskii, F.N.; Bashmakov, I.A.; Novikov, V.P.

    1994-09-20

    Thermal solid-phase conversions of the yttrium-barium-copper salt of tricarboxycellulose (TCC) with a 1-2-3 cation stoichiometry, respectively, have been considered. Yttrium barium cuprate is the end product of the thermal treatment of the triple salt. According to the data of X-ray analysis the onset of 1-2-3 phase formation is noticeable at 750-800{degrees}C. The temperature 875{degrees}C (with a duration of heating of 12 h) is sufficient for practically complete conversion of the Y-Ba-Cu salt of TCC into YBa{sub 2}Cu{sub 3}O{sub 7-{delta}}.

  6. A study to investigate fluoride contamination and fluoride exposure dose assessment in lateritic zones of West Bengal, India.

    PubMed

    Samal, Alok C; Bhattacharya, Piyal; Mallick, Anusaya; Ali, Md Motakabber; Pyne, Jagadish; Santra, Subhas C

    2015-04-01

    To assess the status of severity of fluoride contamination in lateritic Bankura and Purulia districts of West Bengal, concentrations of fluoride in different water sources and agricultural field soils were investigated. The fluoride content (mg/l) was observed to differ with aquifer depths: 0.19-0.47 in dug wells, 0.01-0.17 in shallow tube wells, and 0.07-1.6 in deep tube wells. Fluoride within the World Health Organization (WHO) prescribed range (1.0-1.5 mg/l) was estimated only in ~17% of the total collected water samples while ~67% showed <0.7 mg/l fluoride and thus may impede in the production and maintenance of healthy teeth and bones of the residents, especially children. Fluoride in water was found to be significantly correlated (r = 0.63) with pH. The exposure dose of fluoride (mg/kg/day) from drinking water in infants, children, and adults was estimated in the ranges 0.02-0.53, 0.01-0.24, and 0.01-0.14, respectively against the standard value of 0.05. A clear risk of dental fluorosis is apparent in infants and children of the study area. The fluoride in soil (55-399 mg/kg) was detected to be significantly correlated with the fluoride content in deep tube wells and soil pH (r = 0.56 and 0.71, respectively). The relationships of soil fluoride with total hardness and that with phosphate were not significant. There is a high possibility of bioaccumulation of fluoride from contaminated soil and water of the study area to cultivated crops. This will enhance the quantity of fluoride intake into human food chain in addition to drinking water pathway.

  7. Determination of Fluoride in Toothpaste Using an Ion-Selective Electrode

    ERIC Educational Resources Information Center

    Light, Truman S.; Cappuccino, Carleton C.

    1975-01-01

    Outlines the theory of chemical potentiometry, describes the experimental procedure for free fluoride determination, and presents sample data of fluoride concentration for various brands of toothpaste. (GS)

  8. Bioavailability of fluoride in drinking water: a human experimental study.

    PubMed

    Maguire, A; Zohouri, F V; Mathers, J C; Steen, I N; Hindmarch, P N; Moynihan, P J

    2005-11-01

    It has been suggested that systemic fluoride absorption from drinking water may be influenced by the type of fluoride compound in the water and by water hardness. Using a human double-blind cross-over trial, we conducted this study to measure c(max), T(max), and Area Under the Curve (AUC) for plasma F concentration against time, following the ingestion of naturally fluoridated hard and soft waters, artificially fluoridated hard and soft waters, and a reference water. Mean AUC over 0 to 8 hours was 1330, 1440, 1679, 1566, and 1328 ng F.min.mL(-1) for naturally fluoridated soft, naturally fluoridated hard, artificially fluoridated soft, artificially fluoridated hard, and reference waters, respectively, with no statistically significant differences among waters for AUC, c(max), or T(max). Any differences in fluoride bioavailability between drinking waters in which fluoride is present naturally or added artificially, or the waters are hard or soft, were small compared with large within- and between-subject variations in F absorption. Abbreviations used: F, fluoride; AUC, Area under the Curve for plasma F concentration against time; AUC(0-3), Area under the Curve for plasma F concentration against time for 0 to 3 hours following water ingestion; AUC(0-8), Area under the Curve for plasma F concentration against time for 0 to 8 hours following water ingestion; c(max), maximum plasma F concentration corrected for baseline plasma F and dose (i.e., F concentration of individual waters); T(max), time of c(max).

  9. Supramolecular curcumin-barium prodrugs for formulating with ceramic particles.

    PubMed

    Kamalasanan, Kaladhar; Anupriya; Deepa, M K; Sharma, Chandra P

    2014-10-01

    A simple and stable curcumin-ceramic combined formulation was developed with an aim to improve curcumin stability and release profile in the presence of reactive ceramic particles for potential dental and orthopedic applications. For that, curcumin was complexed with barium (Ba(2+)) to prepare curcumin-barium (BaCur) complex. Upon removal of the unbound curcumin and Ba(2+) by dialysis, a water-soluble BaCur complex was obtained. The complex was showing [M+1](+) peak at 10,000-20,000 with multiple fractionation peaks of MALDI-TOF-MS studies, showed that the complex was a supramolecular multimer. The (1)H NMR and FTIR studies revealed that, divalent Ba(2+) interacted predominantly through di-phenolic groups of curcumin to form an end-to-end complex resulted in supramolecular multimer. The overall crystallinity of the BaCur was lower than curcumin as per XRD analysis. The complexation of Ba(2+) to curcumin did not degrade curcumin as per HPLC studies. The fluorescence spectrum was blue shifted upon Ba(2+) complexation with curcumin. Monodisperse nanoparticles with size less than 200dnm was formed, out of the supramolecular complex upon dialysis, as per DLS, and upon loading into pluronic micelles the size was remaining in similar order of magnitude as per DLS and AFM studies. Stability of the curcumin was improved greater than 50% after complexation with Ba(2+) as per UV/Vis spectroscopy. Loading of the supramloecular nanoparticles into pluronic micelles had further improved the stability of curcumin to approx. 70% in water. These BaCur supramolecule nanoparticles can be considered as a new class of prodrugs with improved solubility and stability. Subsequently, ceramic nanoparticles with varying chemical composition were prepared for changing the material surface reactivity in terms of the increase in, degradability, surface pH and protein adsorption. Further, these ceramic particles were combined with curcumin prodrug formulations and optimized the curcumin release

  10. Defect Chemistry and Microstructure of Complex Perovskite Barium Zinc Niobate

    NASA Astrophysics Data System (ADS)

    Peng, Ping

    1991-02-01

    This dissertation presents a systematic study of the characterization of the phase transitions, microstructures, defects and transport properties of undoped and doped complex perovskite barium zinc niobate (BZN). Complex perovskite BZN is a paraelectric material while its parent material barium titanate is ferroelectric. With codoping of (Zn + 2Nb) into Ti site, BaTiO_3 shows three distinguished features. First, the Curie temperature is lowered; second, the three phase transitions (cubic-tetragonal-orthorhombic-rhombohedral) coalesce; and lastly, the transition becomes diffuse showing a typical 2nd order phase transition compared with 1st order in undoped BaTiO_3. Complex microchemical ordering is another characteristic of BZN. Stoichiometric BZN shows a mixture of two types of ordering schemes. 1:1, 1:2 ordered microdomains and the disordered matrix co-exist. The 1:1 type ordering involves an internal charge imbalance which inhibits the growth of 1:1 type of ordered microdomains. The 1:2 type ordering is consistent with the chemical composition of BZN. These ordering patterns can be modified by either adjustment of the Zn/Nb ratio or by doping. The defect structure of the stoichiometric BZN is closely related to that of BaTiO_3. Stoichiometric BZN is an insulator with wide band gap (~ 3.70 eV). Undoped BZN has a high oxygen vacancy concentration which comes from three possible sources, such as unavoidable acceptor impurities, due to their natural abundance, Zn/Nb ratio uncertainty due to processing limitations, and high temperature ZnO loss due to sintering process. The oxygen vacancy concentration for undoped BZN lays in the neighborhood of 1500 ppm (atm.). The compensation defects for various dopants have also been identified. Both electrons and holes conduct by a small polaron mechanism. Various thermodynamic parameters, such as enthalpies of oxidation and reduction, mass action constants for intrinsic electronic disorder, oxidation and reduction have been

  11. Active experiments in space in conjunction with Skylab. [barium plasma injection experiment and magnetic storm of March 7, 1972

    NASA Technical Reports Server (NTRS)

    Wescott, E. M.

    1974-01-01

    Two papers are presented which relate to the Skylab barium shaped charge experiments. The first describes the L=6.6 OOSIK barium plasma injection experiment and magnetic storm of March 7, 1972. Rocket payload, instrumentation, data reduction methods, geophysical environment at the time of the experiment, and results are given. The second paper presents the observation of an auroral Birkeland current which developed from the distortion of a barium plasma jet during the above experiment.

  12. A simple and colorimetric fluoride receptor and its fluoride-responsive organogel.

    PubMed

    Yu, Xudong; Li, Yajuan; Yin, Yaobing; Yu, Decai

    2012-08-01

    In this paper, a new p-nitrophenylhydrozine-based anion receptor 1 containing cholesterol group had been designed and synthesized. It could selectively recognize fluoride among different anions tested with color changes from pale yellow to red for visual detection. Simultaneously, it could gel in cyclohexane, and the gel was also fluoride-responsive. When treated with TBAF (tetra-n-butylammonium fluoride), the gel could undergo gel-sol transition accompanied by color, morphology and surface changes. The binding mechanism had been investigated by UV-vis and (1)HNMR (proton nuclear magnetic resonance spectra) titrations. From SEM (scanning electron microscope), SAXS (small-angle X-ray scattering), IR (Infrared Spectroscopy) and CA (contact angle) experiments, it was indicated that the addition of F(-) could destroy the molecule assembly of host 1 in the gel state, thus resulting in the gel-to-sol transition due to the binding site competition effect. To the best of our knowledge, this was the simplest fluoride-responsive organogel with high selectivity.

  13. CAN FLUORIDATION AFFECT LEAD (II) IN POTABLE WATER? HEXAFLUOROSILICATE AND FLUORIDE EQUILIBRIA IN AQUEOUS SOLUTION

    EPA Science Inventory

    Recent reports have attempted to show that fluoridating potable water is linked to increased levels of lead(II) in the blood. We examine these claims in light of the established science and critically evaluate their significance. The completeness of hexafluorosilicate hydrolysi...

  14. Method for decontamination of nickel-fluoride-coated nickel containing actinide-metal fluorides

    DOEpatents

    Windt, N.F.; Williams, J.L.

    In one aspect, the invention comprises contacting nickel-fluoride-coated nickel with gaseous ammonia at a temperature effecting nickel-catalyzed dissociation thereof and effecting hydrogen-reduction of the nickel fluoride. The resulting nickel is heated to form a melt and a slag and to effect transfer of actinide metals from the melt into the slag. The melt and slag are then separated. In another aspect, nickel contianing nickel oxide and actinide metals is contacted with ammonia at a temperature effecting nickel-catalyzed dissociation to effect conversion of the nickel oxide to the metal. The resulting nickel is then melted and separated as described. In another aspect nickel-fluoride-coated nickel containing actinide-metal fluorides is contacted with both steam and ammonia. The resulting nickel then is melted and separated as described. The invention is characterized by higher nickel recovery, efficient use of ammonia, a substantial decrease in slag formation and fuming, and a valuable increase in the service life of the furnace liners used for melting.

  15. Digital radiographic measurement of approximal caries progression in fluoridated and non-fluoridated areas of Rio de Janeiro, Brazil.

    PubMed

    Lawrence, H P; Benn, D K; Sheiham, A

    1997-12-01

    The effect of fluoridation on approximal caries progression was investigated using serial digitized bitewing images and conventional film images of 290 12-16-year-old schoolchildren who were lifetime residents of either Rio de Janeiro (a fluoridated area) or Mangaratiba and Angra dos Reis (non-fluoridated areas) in the state of Rio de Janeiro, Brazil. One examiner scored a maximum of 28 approximal surfaces of posterior teeth per subject using both methods. The intraexaminer reliability for rating lesion depth with digital images was comparable with that of the conventional bitewing films (namely, intraclass correlation of 0.99 and weighted Kappa scores of 0.82, respectively). Approximal surface D1S was 3.17 +/- 0.25 (sx) in fluoridated areas and 6.64 +/- 0.44 in non-fluoridated areas. After 1 year, the rate of caries progression in approximal surfaces was significantly lower in the fluoridated areas (0.54 +/- 0.14) as compared with the non-fluoridated areas (1.41 +/- 0.20) using Pitts' scoring system for conventional bitewing radiographs (P < 0.001). Similarly, the digital radiographic method was able to detect subtle differences in approximal caries progression in the enamel and the dentin (overall mean: 0.34 mm/year in fluoridated areas vs 0.49 mm/year in non-fluoridated areas, P < 0.05). The two radiographic methods were strongly correlated (rs = 0.7). Assuming a constant rate over time, these results indicate that lesion progression from the outer half of the enamel into the outer half of the dentin takes approximately 3-4 years in schoolchildren from the fluoridated areas compared to 2 1/2 years in the non-fluoridated areas.

  16. Preparation of thin film silver fluoride electrodes from constituent elements

    NASA Technical Reports Server (NTRS)

    Odonnell, P. M.

    1972-01-01

    The feasibility of preparing thin-film metal fluoride electrodes from the elemental constituents has been demonstrated. Silver fluoride cathodes were prepared by deposition of silver on a conducting graphite substrate followed by fluorination under controlled conditions using elemental fluorine. The resulting electrodes were of high purity, and the variables such as size, shape, and thickness were easily controlled.

  17. Pd-catalyzed C-H fluorination with nucleophilic fluoride.

    PubMed

    McMurtrey, Kate B; Racowski, Joy M; Sanford, Melanie S

    2012-08-17

    The palladium-catalyzed C-H fluorination of 8-methylquinoline derivatives with nucleophilic fluoride is reported. This transformation involves the use of AgF as the fluoride source in combination with a hypervalent iodine oxidant. Both the scope and mechanism of the reaction are discussed.

  18. Methods of controlling hydrogen fluoride pressure during chemical fabrication processes

    SciTech Connect

    Solovyov, Vyacheslav; Wiesmann, Harold

    2009-11-24

    The present invention is a method for producing a crystalline end-product. The method comprising exposing a fluoride-containing precursor to a hydrogen fluoride absorber under conditions suitable for the conversion of the precursor into the crystalline end-product.

  19. Fluoride Analysis. Training Module 5.200.2.77.

    ERIC Educational Resources Information Center

    Kirkwood Community Coll., Cedar Rapids, IA.

    This document is an instructional module package prepared in objective form for use by an instructor familiar with fluoride analysis procedures. Included are objectives, an instructor guide, student handouts, and a list of reference material. This module considers the determination of fluoride in water supplies using the SPANDS and electrode…

  20. A health risk assessment for fluoride in Central Europe.

    PubMed

    Fordyce, F M; Vrana, K; Zhovinsky, E; Povoroznuk, V; Toth, G; Hope, B C; Iljinsky, U; Baker, J

    2007-04-01

    Like many elements, fluorine (which generally occurs in nature as fluoride) is beneficial to human health in trace amounts, but can be toxic in excess. The links between low intakes of fluoride and dental protection are well known; however, fluoride is a powerful calcium-seeking element and can interfere with the calcified structure of bones and teeth in the human body at higher concentrations causing dental or skeletal fluorosis. One of the main exposure routes is via drinking water and the World Health Organisation currently sets water quality guidelines for the element. In Central Europe, groundwater resources that exceed the guideline value of 1.5 mg l-1 are widespread and effects on health of high fluoride in water have been reported. The aim of the current project was to develop a geographic information system (GIS) to aid the identification of areas where high-fluoride waters and fluorosis may be a problem; hence, where water treatment technologies should be targeted. The development of the GIS was based upon the collation and digitisation of existing information relevant to fluoride risk in Ukraine, Moldova, Hungary and Slovakia assembled for the first time in a readily accessible form. In addition, geochemistry and health studies to examine in more detail the relationships between high-fluoride drinking waters and health effects in the population were carried out in Moldova and Ukraine demonstrating dental fluorosis prevalence rates of 60-90% in adolescents consuming water containing 2-7 mg l-1 fluoride.

  1. Preparation of high purity copper fluoride by fluorinating copper hydroxyfluoride

    NASA Technical Reports Server (NTRS)

    King, R. B.; Lundquist, J. R.

    1969-01-01

    Copper fluoride containing no more than 50 ppm of any contaminating element was prepared by the fluorination of copper hydroxyfluoride. The impurity content was obtained by spark source mass spectrometry. High purity copper fluoride is needed as a cathode material for high energy density batteries.

  2. A Process for Making Bulk Heavy Metal Fluoride Glasses.

    DTIC Science & Technology

    This invention relates to the preparation of glasses, and, in particular, relates to the preparation of heavy metal fluoride glasses with...reproducible high optical qualities. Considerable effort has been expended to develop heavy metal fluoride glasses ( HMFG ) as a viable family of infrared

  3. THE EXCHANGE REACTION OF ACETYL FLUORIDE AND ACETYL HEXAFLUOROARSENATE,

    DTIC Science & Technology

    From the temperature dependence of the exchange rate of the methyl protons between acetyl fluoride and acetyl hexafluoroarsenate an Arrhenius...the reaction was found to be one-half order in acetyl hexafluoroarsenate and zero order in acetyl fluoride. (Author)

  4. Applications Of Graphite Fluoride Fibers In Outer Space

    NASA Technical Reports Server (NTRS)

    Hung, Ching-Cheng; Long, Martin; Dever, Therese

    1993-01-01

    Report characterizes graphite fluoride fibers made from commercially available graphitized carbon fibers and discusses some potential applications of graphite fluoride fibers in outer space. Applications include heat-sinking printed-circuit boards, solar concentrators, and absorption of radar waves. Other applications based on exploitation of increased resistance to degradation by atomic oxygen, present in low orbits around Earth.

  5. Fluoride analysis of human milk in remote areas of Thailand.

    PubMed

    Chuckpaiwong, S; Nakornchai, S; Surarit, R; Soo-ampon, S

    2000-09-01

    The objective of this study was to measure the fluoride content in human milk collected from mothers living in remote areas of Thailand and to correlate it with fluoride concentrations in drinking water and water for domestic use. Four to five ml of breast milk were sampled from mothers living in villages where schools under the jurisdiction of the Department of Border Patrol Police were located. The schools were sampled by Multiple Stratified Cluster Random Sampling. Fluoride was determined by microdiffusion method. Statistical analysis were made by ANOVA and LSD test. Correlation between fluoride content in milk and water was assessed by Kendall's tau-b. The mean fluoride concentration in breast milk was 0.017+/-0.02 ppm. There was no difference in breast milk fluoride concentration between regions (p=0.6). No correlation was found between breast milk fluoride content and fluoride concentrations in either drinking water or water for domestic use (r(tau) = -0.09, p = 0.32, r(tau) = -0.04, p = 0.65 respectively).

  6. Fluoride Release by Glass Ionomer Cements, Compomer and Giomer

    PubMed Central

    Mousavinasab, Sayed Mostafa; Meyers, Ian

    2009-01-01

    Background: To measure the amounts of fluoride released from fluoride-containing materials, four glass ionomer cements (Fuji IX, Fuji VII, Fuji IX Extra and Fuji II LC), a compomer (Dyract Extra) and a giomer (Beautifil) were used in this study. Methods: Twenty cylindrical specimens were prepared from each material. The amount of released fluoride was measured during the first week and on the days 14 and 21 by using specific fluoride electrode and an ionanalyzer. The results were statistically analyzed using analysis of variance (two-way ANOVA) and Tukey Kramer multiple comparison tests (p=0.05). Results: Significant differences were seen in fluoride release of different days and materials (p<0.05). The maximum cumulative fluoride release of days 1-7 was related to Fuji VII, followed by Fuji IX Extra, Fuji II LC, Fuji IX, Dyract Extra and Beautifil in descending order and this order remained the same until the 21st day. Conclusion: Fuji IX, Fuji VII, Fuji IX Extra, and Fuji II LC released higher amounts of fluoride compared to Beautifil and Dyract Extra in this study. It seems that the extent of the glass ionomer matrix plays an important role in determining the fluoride releasing ability of glass ionomer cement materials. PMID:21528035

  7. 21 CFR 175.270 - Poly(vinyl fluoride) resins.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... polymerization of vinyl fluoride. (b) The poly(vinyl fluoride) basic resins have an intrinsic viscosity of not... Dilute Solution Viscosity of Vinyl Chloride Polymers,” which is incorporated by reference. Copies may be... Solution Viscosity of Vinyl Chloride Polymers,” which is incorporated by reference; see paragraph (b)...

  8. 21 CFR 175.270 - Poly(vinyl fluoride) resins.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... polymerization of vinyl fluoride. (b) The poly(vinyl fluoride) basic resins have an intrinsic viscosity of not... Dilute Solution Viscosity of Vinyl Chloride Polymers,” which is incorporated by reference. Copies may be... Solution Viscosity of Vinyl Chloride Polymers,” which is incorporated by reference; see paragraph (b)...

  9. 21 CFR 175.270 - Poly(vinyl fluoride) resins.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... polymerization of vinyl fluoride. (b) The poly(vinyl fluoride) basic resins have an intrinsic viscosity of not... Dilute Solution Viscosity of Vinyl Chloride Polymers,” which is incorporated by reference. Copies may be... Solution Viscosity of Vinyl Chloride Polymers,” which is incorporated by reference; see paragraph (b)...

  10. 21 CFR 175.270 - Poly(vinyl fluoride) resins.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... polymerization of vinyl fluoride. (b) The poly(vinyl fluoride) basic resins have an intrinsic viscosity of not... Dilute Solution Viscosity of Vinyl Chloride Polymers,” which is incorporated by reference. Copies may be... Solution Viscosity of Vinyl Chloride Polymers,” which is incorporated by reference; see paragraph (b)...

  11. Abundance analysis of s-process enhanced barium stars

    NASA Astrophysics Data System (ADS)

    Mahanta, Upakul; Karinkuzhi, Drisya; Goswami, Aruna; Duorah, Kalpana

    2016-12-01

    Detailed chemical composition studies of stars with enhanced abundances of neutron-capture elements can provide observational constraints for neutron-capture nucleosynthesis studies and clues for understanding their contribution to the Galactic chemical enrichment. We present abundance results from high-resolution spectral analyses of a sample of four chemically peculiar stars characterized by s-process enhancement. High-resolution spectra (R ˜ 42 000) of these objects spanning a wavelength range from 4000 to 6800 Å are taken from the ELODIE archive. We have estimated the stellar atmospheric parameters, the effective temperature Teff, the surface gravity log g and metallicity [Fe/H] from local thermodynamic equilibrium analysis using model atmospheres. We report estimates of elemental abundances for several neutron-capture elements, Sr, Y, Zr, Ba, La, Ce, Pr, Nd, Sm, Eu and Dy. While HD 49641 and HD 58368 show [Ba/Fe] ≥ 1.16, the other two objects HD 119650 and HD 191010 are found to be mild barium stars with [Ba/Fe] ˜ 0.4. The derived abundances of the elements are interpreted on the basis of existing theories for understanding their origin and evolution.

  12. Thin film barium strontium titanate ferroelectric varactors for microwave applications

    NASA Astrophysics Data System (ADS)

    Yue, Hailing; Spatz, Devin; Wang, Shu; Shin, Eunsung; Subramanyam, Guru

    2015-11-01

    Analog phase shifters are investigated with a periodic structure that includes Barium Strontium Titanate ferroelectric thin film varactors in shunt or serial connection to the coplanar waveguide transmission line. The phase shift is achieved by applying a DC bias to the varactors and changing the reactance in the circuit. The goal of this paper is to characterize the shunt capacitive varactors regarding the voltage dependence of the capacitance, loss tangent, and insertion losses at different bias voltages. Quality factor analysis is also conducted taking the parasitic effects into account. Repeated measurements show that the capacitance of a single cell is tuned from 0.8pF to 0.2pF under a DC bias of 0-10V while the loss tangent is kept under 0.01 in the frequency range of 0-40GHz. Insertion loss is tuned from -4dB to less than -0.6dB from 0 to 10V with a Figure of Merit of 14 degrees/dB at 10GHz and the total quality factor of the unit cell is around 6.7 to 10 at 10GHz with matched port impedance. By cascading 10-25 single unit cells, the phase shift is expected to reach 360 degrees with minimum insertion loss.

  13. Barium oxide, calcium oxide, magnesia, and alkali oxide free glass

    DOEpatents

    Lu, Peizhen Kathy; Mahapatra, Manoj Kumar

    2013-09-24

    A glass composition consisting essentially of about 10-45 mole percent of SrO; about 35-75 mole percent SiO.sub.2; one or more compounds from the group of compounds consisting of La.sub.2O.sub.3, Al.sub.2O.sub.3, B.sub.2O.sub.3, and Ni; the La.sub.2O.sub.3 less than about 20 mole percent; the Al.sub.2O.sub.3 less than about 25 mole percent; the B.sub.2O.sub.3 less than about 15 mole percent; and the Ni less than about 5 mole percent. Preferably, the glass is substantially free of barium oxide, calcium oxide, magnesia, and alkali oxide. Preferably, the glass is used as a seal in a solid oxide fuel/electrolyzer cell (SOFC) stack. The SOFC stack comprises a plurality of SOFCs connected by one or more interconnect and manifold materials and sealed by the glass. Preferably, each SOFC comprises an anode, a cathode, and a solid electrolyte.

  14. Sintering and foaming of barium silicate glass powder compacts

    NASA Astrophysics Data System (ADS)

    Mueller, Ralf; Reinsch, Stefan; Agea-Blanco, Boris

    2016-10-01

    The manufacture of sintered glasses and glass-ceramics, glass matrix composites and glass-bounded ceramics or pastes is often affected by gas bubble formation. Against this background, we studied sintering and foaming of barium silicate glass powders used as SOFC sealants using different powder milling procedures. Sintering was measured by means of heating microscopy backed up by XPD, DTA, Vacuum Hot Extraction (VHE) and optical and electron microscopy. Foaming increased significantly as milling progressed. For moderately milled glass powders, subsequent storage in air could also promote foaming. Although the powder compacts were uniaxially pressed and sintered in air, the milling atmosphere sig¬ni¬ficantly affected foaming. The strength of this effect increased in the order Ar ? N2 < air < CO2. Conformingly, VHE studies revealed that the pores of foamed samples predominantly encapsulated CO2, even for powders milled in Ar and N2. Results of this study thus indicate that foaming is caused by carbonaceous species trapped on the glass powder surface. Foaming could be substantially reduced by milling in water and 10 wt% HCl.

  15. High-pressure phase transition observed in barium hydride

    NASA Astrophysics Data System (ADS)

    Smith, Jesse S.; Desgreniers, Serge; Tse, John S.; Klug, Dennis D.

    2007-08-01

    The pressure-dependent structural and vibrational properties of barium hydride have been studied up to 22 GPa at room temperature by means of powder x-ray diffraction, Raman spectroscopy, and first-principles calculations. At ambient conditions, BaH2 crystallizes in the cotunnite structure (Pnma). A reversible, first-order structural phase transition is observed at 1.6 GPa. The high-pressure phase can be indexed by a hexagonal unit cell with a proposed Ni2In structure (P63/mmc), with the Ba and H atoms in special positions. The experimental volume compression of the high-pressure phase yields an isothermal bulk modulus B0=24(1) GPa (B0' fixed at 4.13). This compares favorably with the results of the first-principles calculations, which reproduce the first-order nature of the transition. The relevance of these results is discussed in the contexts of metal hydrides in particular and ionic AX2(A =metal) compounds in general.

  16. Dielectric and Impedance Spectroscopy of Barium Bismuth Vanadate Ferroelectrics

    NASA Astrophysics Data System (ADS)

    Sutar, B. C.; Choudhary, R. N. P.; Das, Piyush R.

    2014-07-01

    Structural, micro-structural and electrical properties of barium bismuth vanadate Ba(Bi0.5V0.5)O3 ceramics were investigated. X-ray diffraction (XRD) analysis of the prepared material confirmed the formation of the compound with monoclinic crystal system. Scanning electron microscopy (SEM) of the compound exhibits well-defined grains that are uniformly distributed throughout the surface of the sample. Dielectric properties of the compound were studied as a function of temperature at different frequencies. An observation of dielectric anomaly at 295 °C is due to ferroelectric phase transition that was later confirmed by the appearance of hysteresis loop. Detailed studies of complex impedance spectroscopy have provided a better understanding of the relaxation process and correlations between the microstructure-electrical properties of the materials. The nature of frequency dependence of ac conductivity obeys the Debye power law. The dc conductivity, calculated from the ac conductivity spectrum, shows the negative temperature coefficient of resistance behavior similar to that of a semiconductor.

  17. Facile growth of barium oxide nanorods: structural and optical properties.

    PubMed

    Ahmad, Naushad; Wahab, Rizwan; Alam, Manawwer

    2014-07-01

    This paper reports a large-scale synthesis of barium oxide nanorods (BaO-NRs) by simple solution method at a very low-temperature of - 60 degrees C. The as-grown BaO-NRs were characterized in terms of their morphological, structural, compositional, optical and thermal properties. The morphological characterizations of as-synthesized nanorods were done by scanning electron microscopy (SEM) which confirmed that the synthesized products are rod shaped and grown in high density. The nanorods exhibits smooth and clean surfaces throughout their lengths. The crystalline property of the material was analyzed with X-ray diffraction pattern (XRD). The compositional and thermal properties of synthesized nanorods were observed via Fourier transform infrared (FTIR) spectroscopy and thermogravimetric analysis which confirmed that the synthesized nanorods are pure BaO and showed good thermal stability. The nanorods exhibited good optical properties as was confirmed from the room-temperature UV-vis spectroscopy. Finally, a plausible mechanism for the formation of BaO-NRs is also discussed in this paper.

  18. Beta Decay Studies of Short Lived Barium Isotopes

    NASA Astrophysics Data System (ADS)

    Bendall, Charles Skipwith

    The half-lives and relative intensities of several short lived neutron rich isotopes, with atomic numbers between 54 and 57, produced in the spontaneous fission of californium-252 were determined. This was accomplished from the study of the time variation of the K X-ray yields of these isotopes. A transport system which allowed us to study isotopes with half-lives less than 10 seconds was developed. Mass assignments were made by comparing the experimental values of the half-lives with known values. A beta K X-ray coincidence technique was used to obtain the barium beta spectrum in coincidence with lanthanum K X -rays. A Kurie plot was performed on the spectrum to determine the beta groups. The probable origin of each beta group was determined through a comparison of the relative intensities of the isotopes and beta groups. Four beta groups probably from the decay of Ba-145 were revealed. The end point energies of these beta groups are 3870 (+OR-) 432 keV, 2772 (+OR-) 112 keV, 1894 (+OR-) 58 keV, and 746 (+OR-) 38 keV. The three lowest energy groups have not been observed before.

  19. Two new barium sulfonates with pillared layered structures

    NASA Astrophysics Data System (ADS)

    Yang, Jin; Li, Li; Ma, Jian-Fang; Liu, Ying-Ying; Ma, Ji-Cheng

    2006-05-01

    The reactions of BaCl 2·2H 2O with NaHL a and K 3L b (H 2L a=4-hydroxybenzenesulfonic acid, H 3L b=4-hydroxy-5-nitro-1,3-benzenedisulfonic acid) gave two pillared layered coordination polymers: Ba(HL a)(Cl) 1 and KBaL b(H 2O) 32, respectively. The crystal structures were determined by X-ray diffraction method and refined by full-matrix least-squares methods to R=0.0509 and wR=0.1216 using 1455 reflections with I>2 σ( I) for 1; and R=0.0288 and wR=0.0727 using 2661 reflections with I>2 σ( I) for 2. The interesting feature of compound 1 is the coordination actions of chloride anions, which help to form the polymeric layers by bridging barium cations. In compound 2 the Lb3- anion acts as an unusual dodecadente ligand to form a coordination polymer with pillared layered structure.

  20. Two new barium sulfonates with pillared layered structures

    NASA Astrophysics Data System (ADS)

    Yang, Jin; Li, Li; Ma, Jian-Fang; Liu, Ying-Ying; Ma, Ji-Cheng

    2006-08-01

    The reactions of BaCl 2·2H 2O with NaHL a and K 3L b (H 2L a=4-hydroxybenzenesulfonic acid, H 3L b=4-hydroxy-5-nitro-1,3-benzenedisulfonic acid) gave two pillared layered coordination polymers: Ba(HL a)(Cl) 1 and KBaL b(H 2O) 32, respectively. The crystal structures were determined by X-ray diffraction method and refined by full-matrix least-squares methods to R=0.0509 and wR=0.1216 using 1455 reflections with I>2 σ( I) for 1; and R=0.0288 and wR=0.0727 using 2661 reflections with I>2 σ( I) for 2. The interesting feature of compound 1 is the coordination actions of chloride anions, which help to form the polymeric layers by bridging barium cations. In compound 2 the Lb3- anion acts as an unusual dodecadente ligand to form a coordination polymer with pillared layered structure.