Science.gov

Sample records for 55-gallon steel drums

  1. Metal loss characterization in 55-gallon drum steel by the magnetic flux leakage method

    SciTech Connect

    Hockey, R.; Riechers, D.; Duncan, D.

    1995-12-31

    A technique, using Magnetic Flux Leakage (MFL), has been developed for imaging corrosion damage in real-time on the inner surface of sealed 55-gallon drums. An experimental study and theoretical background are presented showing the sensitivity of an MFL technique for detecting and imaging both general and localized corrosion on the inner surface of sealed 55-gallon drums, inspected from the outer surface. Measurements resulting from studies on natural corrosion and machined defects in 55-gallon drum steel will be discussed. Image processing techniques applied to scan data show metal loss in 2-D gray scale images. This work suggests an approach to designing a real-time, full-coverage, 55-gallon drum inspection system to characterize drum wall thickness for comparison over time to determine corrosion rate.

  2. Criticality Safety Controls for 55-Gallon Drums with a Mass Limit of 200 grams Pu-239

    SciTech Connect

    Chou, P

    2011-12-14

    The following 200-gram Pu drum criticality safety controls are applicable to RHWM drum storage operations: (1) Mass (Fissile/Pu) - each 55-gallon drum or its equivalent shall be limited to 200 gram Pu or Pu equivalent; (2) Moderation - Hydrogen materials with a hydrogen density greater than that (0.133 g H/cc) of polyethylene and paraffin are not allowed and hydrogen materials with a hydrogen density no greater than that of polyethylene and paraffin are allowed with unlimited amounts; (3) Interaction - a spacing of 30-inches (76 cm) is required between arrays and 200-gram Pu drums shall be placed in arrays for 200-gram Pu drums only (no mingling of 200-gram Pu drums with other drums not meeting the drum controls associated with the 200-gram limit); (4) Reflection - no beryllium and carbon/graphite (other than the 50-gram waiver amount) is allowed, (note that Nat-U exceeding the waiver amount is allowed when its U-235 content is included in the fissile mass limit of 200 grams); and (5) Geometry - drum geometry, only 55-gallon drum or its equivalent shall be used and array geometry, 55-gallon drums are allowed for 2-high stacking. Steel waste boxes may be stacked 3-high if constraint.

  3. CSER 96-027: storage of cemented plutonium residue containers in 55 gallon drums

    SciTech Connect

    Watson, W.T.

    1997-01-20

    A nuclear criticality safety analysis has been performed for the storage of residual plutonium cementation containers, produced at the Plutonium Finishing Plant, in 55 gallon drums. This CSER increases the limit of total plutonium stored in each 55 gallon drum from 100 to 200 grams.

  4. Fire testing of 55 gallon metal waste drums for dry waste storage

    SciTech Connect

    Hasegawa, H.K.; Staggs, K.J.; Doughty, S.M.

    1993-07-01

    The primary goal of this test program was to conduct a series of fire test to provide information on the fire performance of 55 gallon metal waste drums used for solid waste disposal at Department Of Energy (DOE) facilities. This program was limited in focus to three different types of 55 gallon drums, one radiant heat source, and one specific fire size. The initial test was a single empty 55 gallon drum exposed to a standard ASTME-119 time temperature curve for over 10 minutes. The full scale tests involved metal drums exposed to a 6{prime} diameter flammable liquid fire for a prescribed period of time. The drums contained simulated dry waste materials of primarily class A combustibles. The test results showed that a conventional 55 gallon drum with a 1in. bung would blow its lid consistently.

  5. Design and fabrication of 55-gallon drum shuffler standards

    SciTech Connect

    Long, S.M.; Hsue, F.; Hoth, C.; Fernandez, R.; Bjork, C.; Sprinkle, J.

    1994-08-01

    To analyze waste with varying levels of nuclear material, suitable standards are needed to calibrate analytical instrumentation. At the Los Alamos Plutonium Facility, the authors have designed and fabricated a single drum standard for a passive-active neutron counter (shuffler). The standard is modified simply by adding or subtracting plutonium of uranium cylinders to adapt to a range of nuclear material. The plutonium or uranium oxide was placed into small cylindrical containers (1-in. diameter by 5-in. long) and diluted with diatomaceous earth. The cylinders were welded closed and removed from the glove box environment without any external contamination. The containers were leak tested and then placed on a segmented gamma scanner to assure homogeneous distribution of the nuclear material. The cylinders are now placed into the drum to achieve the needed ranges for calibration of the instruments.

  6. Nondestructive testing methods for 55-gallon, waste storage drums

    SciTech Connect

    Ferris, R.H.; Hildebrand, B.P.; Hockey, R.L.; Riechers, D.M.; Spanner, J.C.; Duncan, D.R.

    1993-06-01

    The Westinghouse Hanford Company (WHC) authorized Pacific Northwest Laboratory (PNL) to conduct a feasibility study to identify promising nondestructive testing (NDT) methods for detecting general and localized (both pitting and pinhole) corrosion in the 55-gal drums that are used to store solid waste materials at the Hanford Site. This document presents results obtained during a literature survey, identifies the relevant reference materials that were reviewed, provides a technical description of the methods that were evaluated, describes the laboratory tests that were conducted and their results, identifies the most promising candidate methods along with the rationale for these selections, and includes a work plan for recommended follow-on activities. This report contains a brief overview and technical description for each of the following NDT methods: magnetic testing techniques; eddy current testing; shearography; ultrasonic testing; radiographic computed tomography; thermography; and leak testing with acoustic detection.

  7. JUSTIFICATION FOR A LIMIT OF 15 PERCENT HYDROGEN IN A 55 GALLON DRUM

    SciTech Connect

    MARUSICH, R.M.

    2007-01-04

    The concentration of 15% hydrogen in air in a waste drum is used as the concentration at which the drum remains intact in the case of a deflagration. The following describes what could happen to the drum if 15% hydrogen or more in air were ignited. Table 2 of the Savannah River report WSRC-TR-90-165 ''TRU Drum Hydrogen Explosion Tests'' provides the results of tests performed in 55-gallon drums filled with hydrogen and air mixtures. The hydrogen-air mixtures were ignited by a hot-wire igniter. The results of the tests are shown in Table 1. They concluded that drums can withstand deflagration involving hydrogen concentration up to 15% hydrogen. Testing was performed at Idaho Falls and documented in a letter from RH Beers, Waste Technology Programs Division, EG&G Idaho, to CP Gertz, Radioactive Waste Technology Branch, DOE dated Sept. 29, 1983. In these tests, 55-gallon drums were filled with hydrogen-air mixtures which were ignited. The results in Table 2.2 showed that ignition for drums containing 11% and 14% hydrogen, the drum lid remained on the drum. Ignition in drum with 30% hydrogen resulted in lid loss. It is concluded from the results of these two tests that, for uncorroded drums, a 15% hydrogen in air mixture will not result in loss of drum integrity (i.e., lid remains on, walls remain intact). The drum walls however, may be thinned due to corrosion. The effect of the deflagration on thinner walls is assessed next. Assume a 15% hydrogen in air mixture exists in a drum. The pressure assuming adiabatic isochoric complete combustion (AICC) conditions is 69 psig (using the same deflagration pressure calculation method as in HNF-19492, ''Revised Hydrogen Deflagration Analysis which got 82 psig for 20% hydrogen in air).

  8. Nuclear Criticality Safety Calculational Analysis for Fissile Mass Limits and Spacing Requirements for 55 - Gallon Waste Drums

    SciTech Connect

    Davis, Thomas C.; Hesse, David J.; Tayloe, Jr., Robert W.

    1994-05-01

    A nuclear criticality safety analysis was performed to determine the fissile mass limits and spacing requirements for the storage of 55-gallon waste drums at the Portsmouth Gaseous Diffusion Plant (PORTS).

  9. CSER 00-006 Storage of Plutonium Residue Containers in 55 Gallon Drums at the PFP

    SciTech Connect

    DOBBIN, K.D.

    2000-05-24

    This criticality safety evaluation report (CSER) provides the required limit set and controls for safe transit and storage of these drums in the 234-5Z Building at the PFP. A mass limit of 200 g of plutonium or fissile equivalent per drum is acceptable

  10. Techniques for improving shuffler assay results for 55-gallon waste drums

    SciTech Connect

    Rinard, P.M.; Prettyman, T.H.; Stuenkel, D.

    1994-08-01

    Accurate assays of the fissile contents in waste drums are needed to ensure the most proper and economical handling and disposal of the waste. An improvement of accuracy will mean fewer drums disposed as transuranic waste when they really contain low-level waste, saving both money and burial sites. Shufflers are used for assaying waste drums and are very accurate with nonmoderating matrices (such as iron). In the active mode they count delayed neutrons released after fissions are induced by irradiation neutrons from a {sup 252}Cf source. However, as the hydrogen density from matrices such as paper or gloves increases, the accuracy can suffer without proper attention. The neutron transport and fission probabilities change with the hydrogen density, causing the neutron count rate to vary with the position of the fissile material within the drum. The magnitude of this variation grows with the hydrogen density.

  11. Results of the gamma-neutron mapper performance test on 55-gallon drums at the RWMC

    SciTech Connect

    Gehrke, R.J.; Lawrence, R.S.; Roybal, L.G.; Svoboda, J.M.; Harker, D.J.; Thompson, D.N.; Carpenter, M.V.; Josten, N.E.

    1995-07-01

    The primary purpose of the gamma-neutron mapper (G@) is to provide accurate and quantitative spatial information of the gamma-ray and neutron radiation fields as a function of position about the excavation of a radioactive waste site. The GNM is designed to operate remotely and can be delivered to any point on an excavation by the robotic gantry crane developed by the dig-face project at the Idaho National Engineering Laboratory (INEL). It can also be easily adapted to other delivery systems. The GNM can be deployed over a waste site at a predetermined scan rate and has sufficient accuracy to identify and quantify radioactive contaminants of importance. The results reported herein are from a performance test conducted at the Transuranic Storage Area, Building 628, of the Radioactive Waste Management Complex located at the INEL. This building is an active interim-storage area for 55-gal drums of transuranic waste from the Department of Energy`s Rocky Flats Plant. The performance test consisted of scanning a stack of drums five high by five wide. Prior to the test, radiation fields were measured by a health physicist at the center of the drums and ranged from 0.5 mR/h to 35 mR/h. Scans of the drums using the GNM were taken at standoff distances from the vertical drum stack of 15 cm, 30 cm, 45 cm, and 90 cm. Data were acquired at scan speeds of 7.5 cm/s and 15 cm/s. The results of these scans and a comparison of these results with the manifests of these drums are compared and discussed.

  12. Criticality Safety Analysis on the Mixed Be, Nat-U, and C (Graphite) Reflectors in 55-Gallon Waste Drums and Their Equivalents for HWM Applications

    SciTech Connect

    Chou, P

    2011-12-14

    The objective of this analysis is to develop and establish the technical basis on the criticality safety controls for the storage of mixed beryllium (Be), natural uranium (Nat-U), and carbon (C)/graphite reflectors in 55-gallon waste containers and/or their equivalents in Hazardous Waste Management (HWM) facilities. Based on the criticality safety limits and controls outlined in Section 3.0, the operations involving the use of mixed-reflector drums satisfy the double-contingency principle as required by DOE Order 420.1 and are therefore criticality safe. The mixed-reflector mass limit is 120 grams for each 55-gallon drum or its equivalent. a reflector waiver of 50 grams is allowed for Be, Nat-U, or C/graphite combined. The waived reflectors may be excluded from the reflector mass calculations when determining if a drum is compliant. The mixed-reflector drums are allowed to mix with the typical 55-gallon one-reflector drums with a Pu mass limit of 120 grams. The fissile mass limit for the mixed-reflector container is 65 grams of Pu equivalent each. The corresponding reflector mass limits are 300 grams of Be, and/or 100 kilograms of Nat-U, and/or 110 kilograms of C/graphite for each container. All other unaffected control parameters for the one-reflector containers remain in effect for the mixed-reflector drums. For instance, Superior moderators, such as TrimSol, Superla white mineral oil No. 9, paraffin, and polyethylene, are allowed in unlimited quantities. Hydrogenous materials with a hydrogen density greater than 0.133 gram/cc are not allowed. Also, an isolation separation of no less than 76.2 cm (30-inch) is required between a mixed array and any other array. Waste containers in the action of being transported are exempted from this 76.2-cm (30-inch) separation requirement. All deviations from the CS controls and mass limits listed in Section 3.0 will require individual criticality safety analyses on a case-by-case basis for each of them to confirm their

  13. ORNL testing of DOT specification 17H drums (55-gallon) for compliance with DOT specifications for Type A packaging

    SciTech Connect

    Baldwin, J.S.; Lasher, L.C.; Van Cleve, J.E. Jr.; Van Hoesen, S.D.

    1986-07-01

    Oak Ridge National Laboratory (ORNL) proposes using Department of Transportation (DOT) specification 17H drums (55-gal) for transporting low-level waste (LLW) to Oak Ridge Gaseous Diffusion Plant (ORGDP) for interim storage. This container type was tested and found to be in compliance with DOT specifications for Type A packaging.

  14. Impact and structural analysis of the INEL 55 gallon recycled shielded storage container

    SciTech Connect

    Richins, W.D.

    1996-07-01

    The INEL Recycled Shielded Storage Containers (RSSC) are designed primarily for the transportation and storage of mixed RH-TRU solid waste using recycled, potentially contaminated lead and stainless steel construction materials. Two versions of the RSSC have been developed accommodating either 30 or 55 gallon drums. This report addresses the structural qualification of the 55 gallon version of the RSSC to DOT 7A Type A requirements. The controlling qualification test is a 4 ft drop onto a rigid surface. During and after this test, the container contents must remain within the container and shielding must not be reduced. The container is also designed to withstand stacking, internal pressure, lifting loads, tiedown failure, penetration, and a range of temperatures. Nonlinear dynamic finite element analyses were performed using a range of material properties. Loads in the major connections and strains in the stainless steel and lead were monitored as a function of time during impact analyses for three simulated drop orientations. Initial results were used to develop the final design. For the final design, the stainless steel and lead have maximum strains well below ultimate levels except at an impact corner where additional deformation is acceptable. The predicted loads in the connections indicate that some yielding will occur but the containment and shielding will remain intact. The results presented here provide assurance that the container will pass the DOT 7A Type A drop tests as well as the other structural requirements.

  15. Magnetic properties of unrusted steel drums from laboratory and field-magnetic measurements

    SciTech Connect

    Ravat, D.

    1996-09-01

    Detection and precise location of buried ferromagnetic objects and estimation of the type and quantity of the objects are becoming increasingly important in environmental investigations worldwide. If laboratory-derived magnetizations were used to model steel drums, the models would under-estimate the resulting magnetic anomalies considerably and, in turn, would overestimate the number of buried drums at an environmental investigation site. Apparent bulk magnetization values for unrusted vertically oriented 55 and 30 gallon drums have been calculated (i.e., the values corrected for the effect of shape demagnetization of the drums). These range from {approximately}90 to {approximately}125 SI units for volume susceptibility and from {approximately} 325 to {approximately} 2,750 A/m for remanent magnetization (based on eight 55 gallon and four 30 gallon drums). Further deviations in these values could arise from the and thickness of the steel and variations in manufacturing conditions affecting magnetizations. From the point of view of modeling the drums, at most source-to-observation distances applicable to environmental investigations, the equivalent source method is able to approximate the observed anomalies of steel drums better than the 3-D modeling method. With two years of rusting, magnetic anomalies of some of the drums have reduced, while in other drums they have slightly increased. The overall magnetic changes caused by rusting appear to be more complex than anticipated, at least in the initial phase of rusting.

  16. African Drum and Steel Pan Ensembles.

    ERIC Educational Resources Information Center

    Sunkett, Mark E.

    2000-01-01

    Discusses how to develop both African drum and steel pan ensembles providing information on teacher preparation, instrument choice, beginning the ensemble, and lesson planning. Includes additional information for the drum ensembles. Lists references and instructional materials, sources of drums and pans, and common note layout/range for steel pan…

  17. FAILURE ANALYSIS: WASTEWATER DRUM BULGING

    SciTech Connect

    Vormelker, P

    2008-09-15

    A 55 gallon wastewater drum lid was found to be bulged during storage in a remote area. Drum samples were obtained for analysis. The interior surface of these samples revealed blistering and holes in the epoxy phenolic drum liner and corrosion of the carbon steel drum. It is suspected that osmotic pressure drove permeation of the water through the epoxy phenolic coating which was weakened from exposure to low pH water. The coating failed at locations throughout the drum interior. Subsequent corrosion of the carbon steel released hydrogen which pressurized the drum causing deformation of the drum lid. Additional samples from other wastewater drums on the same pallet were also evaluated and limited corrosion was visible on the interior surfaces. It is suspected that, with time, the corrosion would have advanced to cause pressurization of these sealed drums.

  18. Ellie Mannette: Master of the Steel Drum.

    ERIC Educational Resources Information Center

    Svaline, J. Marc

    2001-01-01

    Presents an interview with Elliot ("Ellie") Mannette who has played a major role in the development and application of steel drums. States that he has spent most of his life designing and teaching the steel drums. Covers interview topics and background information on Mannette. (CMK)

  19. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Standards for steel drums. 178.504 Section 178.504...-bulk Performance-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2...

  20. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Standards for steel drums. 178.504 Section 178.504...-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for a removable...

  1. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Standards for steel drums. 178.504 Section 178.504...-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for a removable...

  2. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Standards for steel drums. 178.504 Section 178.504...-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for a removable...

  3. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Standards for steel drums. 178.504 Section 178.504...-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for a removable...

  4. L AREA WASTEWATER STORAGE DRUM EVALUATION

    SciTech Connect

    Vormelker, P; Cynthia Foreman, C; Zane Nelson, Z; David Hathcock, D; Dennis Vinson, D

    2007-11-30

    This report documents the determination of the cause of pressurization that led to bulging deformation of a 55 gallon wastewater drum stored in L-Area. Drum samples were sent to SRNL for evaluation. The interior surface of these samples revealed blistering and holes in the epoxy phenolic drum liner and corrosion of the carbon steel drum. It is suspected that osmotic pressure drove permeation of the water through the epoxy phenolic coating which was weakened from exposure to low pH water. The coating failed at locations throughout the drum interior. Subsequent corrosion of the carbon steel released hydrogen which pressurized the drum causing deformation of the drum lid. Additional samples from other wastewater drums on the same pallet were also evaluated and limited corrosion was visible on the interior surfaces. It is suspected that, with time, the corrosion would have advanced to cause pressurization of these sealed drums.

  5. Safety analysis report for packaging (onsite) steel drum

    SciTech Connect

    McCormick, W.A.

    1998-09-29

    This Safety Analysis Report for Packaging (SARP) provides the analyses and evaluations necessary to demonstrate that the steel drum packaging system meets the transportation safety requirements of HNF-PRO-154, Responsibilities and Procedures for all Hazardous Material Shipments, for an onsite packaging containing Type B quantities of solid and liquid radioactive materials. The basic component of the steel drum packaging system is the 208 L (55-gal) steel drum.

  6. Waste drum refurbishment

    SciTech Connect

    Whitmill, L.J.

    1996-10-18

    Low-carbon steel, radioactive waste containers (55-gallon drums) are experiencing degradation due to moisture and temperature fluctuations. With thousands of these containers currently in use; drum refurbishment becomes a significant issue for the taxpayer and stockholders. This drum refurbishment is a non-intrusive, portable process costing between 1/2 and 1/25 the cost of repackaging, depending on the severity of degradation. At the INEL alone, there are an estimated 9,000 drums earmarked for repackaging. Refurbishing drums rather than repackaging can save up to $45,000,000 at the INEL. Based on current but ever changing WIPP Waste Acceptance Criteria (WAC), this drum refurbishment process will restore drums to a WIPP acceptable condition plus; drums with up to 40% thinning o the wall can be refurbished to meet performance test requirements for DOT 7A Type A packaging. A refurbished drum provides a tough, corrosion resistant, waterproof container with longer storage life and an additional containment barrier. Drums are coated with a high-pressure spray copolymer material approximately .045 inches thick. Increase in internal drum temperature can be held to less than 15 F. Application can be performed hands-on or the equipment is readily adaptable and controllable for remote operations. The material dries to touch in seconds, is fully cured in 48 hours and has a service temperature of {minus}60 to 500 F. Drums can be coated with little or no surface preparation. This research was performed on drums however research results indicate the coating is very versatile and compatible with most any material and geometry. It could be used to provide abrasion resistance, corrosion protection and waterproofing to almost anything.

  7. Hot air drum evaporator

    DOEpatents

    Black, Roger L.

    1981-01-01

    An evaporation system for aqueous radioactive waste uses standard 30 and 55 gallon drums. Waste solutions form cascading water sprays as they pass over a number of trays arranged in a vertical stack within a drum. Hot dry air is circulated radially of the drum through the water sprays thereby removing water vapor. The system is encased in concrete to prevent exposure to radioactivity. The use of standard 30 and 55 gallon drums permits an inexpensive compact modular design that is readily disposable, thus eliminating maintenance and radiation build-up problems encountered with conventional evaporation systems.

  8. 49 CFR 178.506 - Standards for metal drums other than steel or aluminum.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Standards for metal drums other than steel or... drums other than steel or aluminum. (a) The following are the identification codes for metal drums other than steel or aluminum: (1) 1N1 for a non-removable head metal drum; and (2) 1N2 for a removable...

  9. 49 CFR 178.506 - Standards for metal drums other than steel or aluminum.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Standards for metal drums other than steel or... drums other than steel or aluminum. (a) The following are the identification codes for metal drums other than steel or aluminum: (1) 1N1 for a non-removable head metal drum; and (2) 1N2 for a removable...

  10. 49 CFR 178.506 - Standards for metal drums other than steel or aluminum.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Standards for metal drums other than steel or... drums other than steel or aluminum. (a) The following are the identification codes for metal drums other than steel or aluminum: (1) 1N1 for a non-removable head metal drum; and (2) 1N2 for a removable...

  11. DEGRADATION EVALUATION OF HEAVY WATER DRUMS AND TANKS

    SciTech Connect

    Mickalonis, J.; Vormelker, P.

    2009-07-31

    Heavy water with varying chemistries is currently being stored in over 6700 drums in L- and K-areas and in seven tanks in L-, K-, and C-areas. A detailed evaluation of the potential degradation of the drums and tanks, specific to their design and service conditions, has been performed to support the demonstration of their integrity throughout the desired storage period. The 55-gallon drums are of several designs with Type 304 stainless steel as the material of construction. The tanks have capacities ranging from 8000 to 45600 gallons and are made of Type 304 stainless steel. The drums and tanks were designed and fabricated to national regulations, codes and standards per procurement specifications for the Savannah River Site. The drums have had approximately 25 leakage failures over their 50+ years of use with the last drum failure occurring in 2003. The tanks have experienced no leaks to date. The failures in the drums have occurred principally near the bottom weld, which attaches the bottom to the drum sidewall. Failures have occurred by pitting, crevice and stress corrosion cracking and are attributable, in part, to the presence of chloride ions in the heavy water. Probable degradation mechanisms for the continued storage of heavy water were evaluated that could lead to future failures in the drum or tanks. This evaluation will be used to support establishment of an inspection plan which will include susceptible locations, methods, and frequencies for the drums and tanks to avoid future leakage failures.

  12. 49 CFR 178.506 - Standards for metal drums other than steel or aluminum.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Standards for metal drums other than steel or... SPECIFICATIONS FOR PACKAGINGS Non-bulk Performance-Oriented Packaging Standards § 178.506 Standards for metal drums other than steel or aluminum. (a) The following are the identification codes for metal drums...

  13. 49 CFR 178.506 - Standards for metal drums other than steel or aluminum.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Standards for metal drums other than steel or...) SPECIFICATIONS FOR PACKAGINGS Non-bulk Performance-Oriented Packaging Standards § 178.506 Standards for metal drums other than steel or aluminum. (a) The following are the identification codes for metal drums...

  14. Hot air drum evaporator. [Patent application

    DOEpatents

    Black, R.L.

    1980-11-12

    An evaporation system for aqueous radioactive waste uses standard 30 and 55 gallon drums. Waste solutions form cascading water sprays as they pass over a number of trays arranged in a vertical stack within a drum. Hot dry air is circulated radially of the drum through the water sprays thereby removing water vapor. The system is encased in concrete to prevent exposure to radioactivity. The use of standard 30 and 55 gallon drums permits an inexpensive compact modular design that is readily disposable, thus eliminating maintenance and radiation build-up problems encountered with conventional evaporation systems.

  15. One-trip drum operating instruction

    SciTech Connect

    Ruff, D.T.

    1994-10-01

    The one trip system is a bagless transfer system for egress of waste from gloveboxes into 55 gallon one-trip drums. The contents of this document give an overview of the assembly, loading, and handling of the one-trip drum for use in the WRAP-1 plant.

  16. Multi-Cultural Awareness Project, the Organization and Implementation of a "World Steel Drum Ensemble".

    ERIC Educational Resources Information Center

    Lawson, Stanley G.

    This proposal describes the organization and implementation of a "World Steel Drum Ensemble" as a strategy to solve the problems of low minority academic achievement, high minority discipline incidents, and minority isolationism. The drum ensemble studied and performed music from Caribbean, Hispanic, and African heritages in a middle…

  17. Criticality evaluation for the storage of converter plates in drums

    SciTech Connect

    Hu, J.P.; Rorer, D.C.; Liu, H.B.

    1993-12-31

    A criticality safety evaluation was performed to support the temporary storage of 20%-enriched uranium converter plates for future use in the Brookhaven Medical Research Reactor (BMRR). A total of twelve such plates each containing approximately one kilogram of the {sup 235}U will be stored in DOT-certified 6M-drums, which have the same dimensions as standard 55-gallon drums except that they are twice as high (178.5cm). Each drum contains a Celotex liner surrounding a central 12.7cm-dia steel pipe. The plates have a nominal size of 0.3cm{times}l0.5cm{times}l25.7cm and fit inside the steel pipe, which extends 130cm in the axial direction. Because the accommodation of twelve plates in one drum is physically possible and more economical, this option for plate storage would be recommended provided that the criticality safety limit is not exceeded. In this paper, the neutron multiplication K{sub eff} in drums is calculated using the Monte Carlo Neutron and Photon Transport code (MCNP). For conservatism, several different configurations which could result.in the most reactive conditions for K{sub eff} have been examined. As part of the effort to optimize the arrangement of plates in drums, a second group of the MCNP calculations is performed using twelve plates evenly contained within two drums placed immediately adjacent to each other model again simulates the most reactive conditions for K{sub eff} estimations.

  18. 49 CFR Appendix C to Part 178 - Nominal and Minimum Thicknesses of Steel Drums and Jerricans

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Nominal and Minimum Thicknesses of Steel Drums and Jerricans C Appendix C to Part 178 Transportation Other Regulations Relating to Transportation (Continued...) SPECIFICATIONS FOR PACKAGINGS Pt. 178, App. C Appendix C to Part 178—Nominal and Minimum Thicknesses of...

  19. 49 CFR Appendix C to Part 178 - Nominal and Minimum Thicknesses of Steel Drums and Jerricans

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Nominal and Minimum Thicknesses of Steel Drums and Jerricans C Appendix C to Part 178 Transportation Other Regulations Relating to Transportation (Continued...) SPECIFICATIONS FOR PACKAGINGS Pt. 178, App. C Appendix C to Part 178—Nominal and Minimum Thicknesses of...

  20. 49 CFR Appendix C to Part 178 - Nominal and Minimum Thicknesses of Steel Drums and Jerricans

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Nominal and Minimum Thicknesses of Steel Drums and Jerricans C Appendix C to Part 178 Transportation Other Regulations Relating to Transportation (Continued...) SPECIFICATIONS FOR PACKAGINGS Pt. 178, App. C Appendix C to Part 178—Nominal and Minimum Thicknesses of...

  1. 49 CFR Appendix C to Part 178 - Nominal and Minimum Thicknesses of Steel Drums and Jerricans

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Nominal and Minimum Thicknesses of Steel Drums and Jerricans C Appendix C to Part 178 Transportation Other Regulations Relating to Transportation PIPELINE AND... SPECIFICATIONS FOR PACKAGINGS Pt. 178, App. C Appendix C to Part 178—Nominal and Minimum Thicknesses of...

  2. 49 CFR Appendix C to Part 178 - Nominal and Minimum Thicknesses of Steel Drums and Jerricans

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Nominal and Minimum Thicknesses of Steel Drums and Jerricans C Appendix C to Part 178 Transportation Other Regulations Relating to Transportation (Continued...) SPECIFICATIONS FOR PACKAGINGS Pt. 178, App. C Appendix C to Part 178—Nominal and Minimum Thicknesses of...

  3. Corrosion susceptibility of steel drums to be used as containers for intermediate level nuclear waste

    NASA Astrophysics Data System (ADS)

    Farina, S.; Schulz Rodriguez, F.; Duffó, G.

    2013-07-01

    The present work is a study of the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins contaminated with different types and concentrations of aggressive species. A special type of specimen was manufactured to simulate the cemented ion-exchange resins in the drum. The evolution of the corrosion potential and the corrosion rate of the steel, as well as the electrical resistivity of the matrix were monitored over a time period of 900 days. The aggressive species studied were chloride ions (the main ionic species of concern) and sulphate ions (produced during radiolysis of the cationic exchange-resins after cementation). The work was complemented with an analysis of the corrosion products formed on the steel in each condition, as well as the morphology of the corrosion products. When applying the results obtained in the present work to estimate the corrosion depth of the steel drumscontaining the cemented radioactive waste after a period of 300 years (foreseen durability of the Intermediate Level Radioactive Waste facility in Argentina) , it is found that in the most unfavourable case (high chloride contamination), the corrosion penetration will be considerably lower than the thickness of the wall of the steel drums.

  4. Inspection, testing, and operating requiremens for the packaging and shipping of uranium trioxide in 55-gallon Department of Transportation (DOT) Specification 6M shipping packagings

    SciTech Connect

    Toomer, D.V.

    1991-06-01

    This document identifies the inspection, testing and operating requirements for the packaging, loading, and shipping of uranium trioxide (UO{sub 3}) in 55-gallon DOT Specification 6M shipping packagings from the Idaho Chemical Processing Plant (ICPP). Compliance with this document assures established controls for the purchasing, packaging, loading, and shipping of DOT Specification 6M shipping packagings are maintained in strict accordance with applicable Code of Federal Regulations (CFRs) and Department of Energy (DOE) Orders. 7 refs., 3 figs., 1 tab.

  5. Stainless steel recycle FY94 progress report

    SciTech Connect

    Imrich, K.J.

    1994-10-28

    The Materials Technology Section (MTS) of the Savannah River Technology Center (SRTC) was asked to demonstrate the practicality of recycling previously contaminated stainless steel components such as reactor heat exchanger heads, process water piping and slug buckets into 208 liters (55 gallon) drums and 2.8 cubic meter (100 ft{sup 3}) storage boxes. Radioactively contaminated stainless steel scrap will be sent to several industrial partners where it will be melted, decontaminated/cast into ingots, and rolled into plate and sheet and fabricated into the drums and boxes. As part of this recycle initiative, MTS was requested to demonstrate that radioactively contaminated Type 304L stainless steel could be remelted and cast to meet the applicable ASTM specification for fabrication of drums and boxes. In addition, MTS was requested to develop the technical basis of melt decontamination and establish practicality of using this approach for value added products. The findings presented in this investigation lead to the following conclusions: recycle of 18 wt% Cr-8 wt% Ni alloy can be achieved by melting Type 304 stainless steel in a air vacuum induction furnace; limited melt decontamination of the contaminated stainless steel was achieved, surface contamination was removed by standard decontamination techniques; carbon uptake in the as-cast ingots resulted from the graphite susceptor used in this experiment and is unavoidable with this furnace configuration. A new furnace optimized for melting stainless steel has been installed and is currently being tested for use in this program.

  6. THERMAL PERFORMANCE ANALYSIS FOR WSB DRUM

    SciTech Connect

    Lee, S

    2008-06-26

    The Nuclear Nonproliferation Programs Design Authority is in the design stage of the Waste Solidification Building (WSB) for the treatment and solidification of the radioactive liquid waste streams generated by the Pit Disassembly and Conversion Facility (PDCF) and Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF). The waste streams will be mixed with a cementitious dry mix in a 55-gallon waste container. Savannah River National Laboratory (SRNL) has been performing the testing and evaluations to support technical decisions for the WSB. Engineering Modeling & Simulation Group was requested to evaluate the thermal performance of the 55-gallon drum containing hydration heat source associated with the current baseline cement waste form. A transient axi-symmetric heat transfer model for the drum partially filled with waste form cement has been developed and heat transfer calculations performed for the baseline design configurations. For this case, 65 percent of the drum volume was assumed to be filled with the waste form, which has transient hydration heat source, as one of the baseline conditions. A series of modeling calculations has been performed using a computational heat transfer approach. The baseline modeling results show that the time to reach the maximum temperature of the 65 percent filled drum is about 32 hours when a 43 C initial cement temperature is assumed to be cooled by natural convection with 27 C external air. In addition, the results computed by the present model were compared with analytical solutions. The modeling results will be benchmarked against the prototypic test results. The verified model will be used for the evaluation of the thermal performance for the WSB drum.

  7. Evaluation of residue drum storage safety risks

    SciTech Connect

    Conner, W.V.

    1994-06-17

    A study was conducted to determine if any potential safety problems exist in the residue drum backlog at the Rocky Flats Plant. Plutonium residues stored in 55-gallon drums were packaged for short-term storage until the residues could be processed for plutonium recovery. These residues have now been determined by the Department of Energy to be waste materials, and the residues will remain in storage until plans for disposal of the material can be developed. The packaging configurations which were safe for short-term storage may not be safe for long-term storage. Interviews with Rocky Flats personnel involved with packaging the residues reveal that more than one packaging configuration was used for some of the residues. A tabulation of packaging configurations was developed based on the information obtained from the interviews. A number of potential safety problems were identified during this study, including hydrogen generation from some residues and residue packaging materials, contamination containment loss, metal residue packaging container corrosion, and pyrophoric plutonium compound formation. Risk factors were developed for evaluating the risk potential of the various residue categories, and the residues in storage at Rocky Flats were ranked by risk potential. Preliminary drum head space gas sampling studies have demonstrated the potential for formation of flammable hydrogen-oxygen mixtures in some residue drums.

  8. Analysis, scale modeling, and full-scale tests of low-level nuclear-waste-drum response to accident environments

    SciTech Connect

    Huerta, M.; Lamoreaux, G.H.; Romesberg, L.E.; Yoshimura, H.R.; Joseph, B.J.; May, R.A.

    1983-01-01

    This report describes extensive full-scale and scale-model testing of 55-gallon drums used for shipping low-level radioactive waste materials. The tests conducted include static crush, single-can impact tests, and side impact tests of eight stacked drums. Static crush forces were measured and crush energies calculated. The tests were performed in full-, quarter-, and eighth-scale with different types of waste materials. The full-scale drums were modeled with standard food product cans. The response of the containers is reported in terms of drum deformations and lid behavior. The results of the scale model tests are correlated to the results of the full-scale drums. Two computer techniques for calculating the response of drum stacks are presented. 83 figures, 9 tables.

  9. Hanford contact-handled transuranic drum retrieval project planning document

    SciTech Connect

    DEMITER, J.A.

    1998-11-17

    The Hanford Site is one of several US Department of Energy (DOE) sites throughout the US that has generated and stored transuranic (TRU) wastes. The wastes were primarily placed in 55-gallon drums, stacked in trenches, and covered with soil. In 1970, the Nuclear Regulatory Commission ordered that TRU wastes be segregated from other radioactive wastes and placed in retrievable storage until such time that the waste could be sent to a geologic repository and permanently disposed. Retrievable storage also defined container storage life by specifying that a container must be retrievable as a contamination-free container for 20 years. Hanford stored approximately 37,400 TRU containers in 20-year retrievable storage from 1970 to 1988. The Hanford TRU wastes placed in 20-year retrievable storage are considered disposed under existing Resource Conservation and Recovery Act (RCRA) regulations since they were placed in storage prior to September 1988. The majority of containers were 55-gallon drums, but 20-year retrievable storage includes several TRU wastes covered with soil in different storage methods.

  10. Screening and Spectral Summing of LANL Empty Waste Drums - 13226

    SciTech Connect

    Gruetzmacher, Kathleen M.; Bustos, Roland M.; Ferran, Scott G.; Gallegos, Lucas E.; Lucero, Randy P.

    2013-07-01

    Empty 55-gallon drums that formerly held transuranic (TRU) waste (often over-packed in 85- gallon drums) are generated at LANL and require radiological characterization for disposition. These drums are typically measured and analyzed individually using high purity germanium (HPGe) gamma detectors. This approach can be resource and time intensive. For a project requiring several hundred drums to be characterized in a short time frame, an alternative approach was developed. The approach utilizes a combination of field screening and spectral summing that was required to be technically defensible and meet the Nevada Nuclear Security Site (NNSS) Waste Acceptance Criteria (WAC). In the screening phase of the operation, the drums were counted for 300 seconds (compared to 600 seconds for the typical approach) and checked against Low Level (LL)/TRU thresholds established for each drum configuration and detector. Multiple TRU nuclides and multiple gamma rays for each nuclide were evaluated using an automated spreadsheet utility that can process data from up to 42 drums at a time. Screening results were reviewed by an expert analyst to confirm the field LL/TRU determination. The spectral summing analysis technique combines spectral data (channel-by-channel) associated with a group of individual waste containers producing a composite spectrum. The grouped drums must meet specific similarity criteria. Another automated spreadsheet utility was used to spectral sum data from an unlimited number of similar drums grouped together. The composite spectrum represents a virtual combined drum for the group of drums and was analyzed using the SNAP{sup TM}/Radioassay Data Sheet (RDS)/Batch Data Report (BDR) method. The activity results for a composite virtual drum were divided equally amongst the individual drums to generate characterization results for each individual drum in the group. An initial batch of approximately 500 drums were measured and analyzed in less than 2 months in 2011

  11. Mechanical Modeling of a WIPP Drum Under Pressure

    SciTech Connect

    Smith, Jeffrey A.

    2014-11-25

    Mechanical modeling was undertaken to support the Waste Isolation Pilot Plant (WIPP) technical assessment team (TAT) investigating the February 14th 2014 event where there was a radiological release at the WIPP. The initial goal of the modeling was to examine if a mechanical model could inform the team about the event. The intention was to have a model that could test scenarios with respect to the rate of pressurization. It was expected that the deformation and failure (inability of the drum to contain any pressure) would vary according to the pressurization rate. As the work progressed there was also interest in using the mechanical analysis of the drum to investigate what would happen if a drum pressurized when it was located under a standard waste package. Specifically, would the deformation be detectable from camera views within the room. A finite element model of a WIPP 55-gallon drum was developed that used all hex elements. Analyses were conducted using the explicit transient dynamics module of Sierra/SM to explore potential pressurization scenarios of the drum. Theses analysis show similar deformation patterns to documented pressurization tests of drums in the literature. The calculated failure pressures from previous tests documented in the literature vary from as little as 16 psi to 320 psi. In addition, previous testing documented in the literature shows drums bulging but not failing at pressures ranging from 69 to 138 psi. The analyses performed for this study found the drums failing at pressures ranging from 35 psi to 75 psi. When the drums are pressurized quickly (in 0.01 seconds) there is significant deformation to the lid. At lower pressurization rates the deformation of the lid is considerably less, yet the lids will still open from the pressure. The analyses demonstrate the influence of pressurization rate on deformation and opening pressure of the drums. Analyses conducted with a substantial mass on top of the closed drum demonstrate that the

  12. Degradation of transuranic waste drums in underground storage at the Hanford Site

    SciTech Connect

    Duncan, D.R.

    1996-05-07

    In situ inspections were performed on tarp-covered 55-gallon drums of transuranic (TRU) waste stored underground at the Hanford Site. These inspections were part of a task to characterize TRU drums for extent of corrosion degradation and uncertainty in TRU designation (inaccuracy in earlier assay determinations may have led to drums that actually were low-level waste to be termed TRU), and to attempt to correlate accuracy of existing records with actual drum contents. Two separate storage trench sites were investigated; a total of 90 drums were inspected with ultrasonic techniques and 104 additional drums were visually inspected. A high-humidity environment in the underground storage trenches had been reported in earlier investigations and was expected to result in substantial corrosion degradation. However, corrosion was much less than expected. Only a small percentage of drums had significant corrosion (with one breach) and the maximum rate was estimated at 0.051 mm/yr (2 mils/yr). The corrosion time of underground exposure was 14 to 15 years. These inspection results should be applicable to other similar environments (this applicability should be restricted to arid climates such as the Hanford Site) where drums are stored underground but shielded from direct soil contact by a tarp or other means. Soil contact would lead to more rapid corrosion.

  13. Degradation of transuranic waste drums in underground storage at the Hanford Site

    SciTech Connect

    Duncan, D.R.; Demiter, J.A.; DeRosa, D.C.

    1996-12-31

    In situ inspections were performed on tarp-covered 55-gallon drums of transuranic (TRU) waste stored underground at the Hanford Site. These inspections were part of a task to characterize TRU drums for extent of corrosion degradation and uncertainty in TRU designation (inaccuracy in earlier assay determinations may have led to drums that actually were low-level waste to be termed TRU), and to attempt to correlate accuracy of existing records with actual drum contents. Two separate storage trench sites were investigated; a total of 90 drums were inspected with ultrasonic techniques and 104 additional drums were visually inspected. A high-humidity environment in the underground storage trenches had been reported in earlier investigations and was expected to result in substantial corrosion degradation. However, corrosion was much less than expected. Only a small percentage of drums had significant corrosion (with one breach) and the maximum rate was estimated at 0.051 mm/yr (2 mils/yr). The corrosion time of underground exposure was 14 to 15 years. These inspection results should be applicable to other similar environments (this applicability should be restricted to arid climates such as the Hanford Site) where drums are stored underground but shielded from direct soil contact by a tarp or other means. Soil contact would lead to more rapid corrosion.

  14. Elevated drum testing Phase 1 test plan

    SciTech Connect

    McBeath, R.S.; Meeuwsen, P.V.

    1994-09-01

    An important part of the Hanford environmental mission is the packaging, transportation, and storage of solid radioactive wastes in metal drums. Presently storage drums are placed four to a wooden pallet with the drums banded to each other. Palletized drums are stacked three units high in pre-engineered steel structures in the 200 Area of the Hanford site. Permitted storage space is expensive to construct, maintain, and operate. Storage capacity is increased if additional drum can be stacked within existing facilities and a cost savings over new construction realized. The purpose of this plan is to outline the testing required to provide the safety criteria for elevated (i.e., tiers of four high) drum storage. The major safety concern with elevated drum storage is the danger of a significant fire in the storage facility. The major fire load within the storage facilities is combustible material contained in the drums. If a seismic event, fork lift accident, or other credible incident were to cause drum failure or lid separation, combustible material could be available for fuel. To increase the initial burn in the facilities, the drums must spill their combustible contents, making them free for ignition. If it can be shown that there is not sufficient damage to the drums to allow for release of their solid contents, then the data used for safety documentation will be re-examined. Preliminary tests conducted in the configurations detailed in this test plan have shown that drums maintain their integrity; that is the drum covers remain attached and the drums do not breach. These tests will be conducted by Westinghouse Hanford Company, Equipment Development organization, who is the designated DOE Center of Excellence to conduct drop tests for Department of Transportation (DOT) certification of DOE designed packages and containers.

  15. Response to requests by FMF and DWPF concerning disposal of FMF saltstone drums in Z-Area vaults

    SciTech Connect

    Langton, C.A.; Cook, J.R.

    1989-07-25

    Disposal of FMF saltstone in 55 gallon drums in the Z-Area Industrial Waste Landfill requires modification of the landfill permit. Approximately 5000 drums of FMF saltstone are currently stored on SC DHEC-permitted concrete storage pads adjacent to the burial ground. At a meeting with DWPF, FMF, and EPS on July 18, 1989, IWT agreed to supply the following information: (1) Consequence of disposal of CCA (Cu, Cr, As) treated wood pallets in the Z-Area vaults. (Four drums of FMF saltstone are currently banded to each pallet.) (2) Consequence of placing partially filled FMF drums in the Z-Area vaults. (3) Formulation for clean grout back-fill. Grout will be emplaced around and over the drums, thereby isolating them from environment (rainwater) prior to vault capping. (4) Maximum loading of FMF saltstone drums in the Z-Area vaults. (5) Consequence of void volume in drums, in clean grout, or both on groundwater modeling results. This document is a response to the above requests.

  16. Results for the Independent Sampling and Analysis of Used Oil Drums at the Impact Services Facility in Oak Ridge, TN

    SciTech Connect

    2013-04-25

    The U.S. Department of Energy (DOE) requested that Oak Ridge Associated Universities (ORAU), via the Oak Ridge Institute for Science and Education (ORISE) contract, perform independent sampling and analysis of used oils contained within eight 55 gallon drums stored at the former IMPACT Services facility, located at the East Tennessee Technology Park in Oak Ridge, Tennessee. These drums were originally delivered by LATA Sharp Remediation Services (LSRS) to IMPACT Services on January 11, 2011 as part of the Bldg. K-33 demolition project, and the drums plus contents should have been processed as non-hazardous non-radiological waste by IMPACT Services. LSRS received a certificate of destruction on August 29, 2012 (LSRS 2012a). However, IMPACT Services declared bankruptcy and abandoned the site later in 2012, and eight of the original eleven K-33 drums are currently stored at the facility. The content of these drums is the subject of this investigation. The original drum contents were sampled by LSRS in 2010 and analyzed for gross alpha, gross beta, and polychlorinated biphenyls (PCBs), using both compositing and grab sampling techniques. The objective of this 2013 sample and analysis effort was to duplicate, to the extent possible, the 2010 sampling and analysis event to support final disposition decisions. Part of that decision process includes either verifying or refuting the assertion that oils that are currently stored in drums at the IMPACT Services facility originated from Bldg. K-33 equipment.

  17. Field test results for radioactive waste drum characterization with Waste Inspection Tomography (WIT)

    SciTech Connect

    Bernardi, R.T.

    1997-11-01

    This paper summarizes the design, fabrication, factory testing, evaluation and demonstration of waste inspection tomography (WIT). WIT consists of a self-sufficient, mobile semi-trailer for Non-Destructive Evaluation and Non-Destructive Assay (NDE/NDA) characterization of nuclear waste drums using X-ray and gamma-ray tomographic techniques. The 23-month WIT Phase I initial test results include 2 MeV Digital Radiography (DR), Computed Tomography (CT), Anger camera imaging, Single Photon Emission Computed Tomography (SPECT), Gamma-Ray Spectroscopy, Collimated Gamma Scanning (CGS), and Active and Passive Computed Tomography (A&PCT) using a 1.4 mCi source of {sup 166}Ho. These techniques were initially demonstrated on a 55-gallon phantom drum with three simulated waste matrices of combustibles, heterogeneous metals, and cement using check sources of gamma active isotopes. Waste matrix identification, isotopic identification, and attenuation-corrected gamma activity determination were all demonstrated nondestructively and noninvasively. Preliminary field tests results with nuclear waste drums are summarized. WIT has inspected drums with 0 to 20 grams plutonium 239. The minimum measured was 0.131 gram plutonium 239 in cement. 8 figs.

  18. HYDROGEN GENERATION FROM SLUDGE SAMPLE BOTTLES CAUSED BY RADIOLYSIS AND CHEMISTRY WITH CONCETNRATION DETERMINATION IN A STANDARD WASTE BOX (SWB) OR DRUM FOR TRANSPORT

    SciTech Connect

    RILEY DL; BRIDGES AE; EDWARDS WS

    2010-03-30

    A volume of 600 mL of sludge, in 4.1 L sample bottles (Appendix 7.6), will be placed in either a Super Pig (Ref. 1) or Piglet (Ref. 2, 3) based on shielding requirements (Ref. 4). Two Super Pigs will be placed in a Standard Waste Box (SWB, Ref. 5), as their weight exceeds the capacity of a drum; two Piglets will be placed in a 55-gallon drum (shown in Appendix 7.2). The generation of hydrogen gas through oxidation/corrosion of uranium metal by its reaction with water will be determined and combined with the hydrogen produced by radiolysis. The hydrogen concentration in the 55-gallon drum and SWB will be calculated to show that the lower flammability limit of 5% hydrogen is not reached. The inner layers (i.e., sample bottle, bag and shielded pig) in the SWB and drum will be evaluated to assure no pressurization occurs as the hydrogen vents from the inner containers (e.g., shielded pigs, etc.). The reaction of uranium metal with anoxic liquid water is highly exothermic; the heat of reaction will be combined with the source term decay heat, calculated from Radcalc, to show that the drum and SWB package heat load limits are satisfied. This analysis does five things: (1) Estimates the H{sub 2} generation from the reaction of uranium metal with water; (2) Estimates the H{sub 2} generation from radiolysis (using Radcalc 4.1); (3) Combines both H{sub 2} generation amounts, from Items 1 and 2, and determines the percent concentration of H{sub 2} in the interior of an SWB with two Super Pigs, and the interior of a 55-gallon drum with two Piglets; (4) From the combined gas generation rate, shows that the pressure at internal layers is minimal; and (5) Calculates the maximum thermal load of the package, both from radioactive decay of the source and daughter products as calculated/reported by Radcalc 4.1, and from the exothermic reaction of uranium metal with water.

  19. 49. EASTERN VIEW OF DORROLIVER VACUUM DRUM FILTER ASSEMBLY IN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    49. EASTERN VIEW OF DORR-OLIVER VACUUM DRUM FILTER ASSEMBLY IN THE FILTER CAKE HOUSE. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

  20. Determining site-specific drum loading criteria for storing combustible {sup 238}Pu waste

    SciTech Connect

    Marshall, R.S.; Callis, E.L.; Cappis, J.H.; Espinoza, J.M.; Foltyn, E.M.; Reich, B.T.; Smith, M.C.

    1994-02-01

    Waste containing hydrogenous-combustible material contaminated with {sup 238}Pu can generate hydrogen gas at appreciable rates through alpha radiolysis. To ensure safe transportation of WIPP drums, the limit for {sup 238}Pu-combustible waste published in the WIPP TRUPACT-11 CONTENT (TRUCON) CODES is 21 milliwafts per 55 gallon drum. This corresponds to about 45 milligrams of {sup 238}PuO{sub 2} used for satellite heat source-electrical generators. The Los Alamos waste storage site adopted a {sup 238}Pu waste storage criteria based on these TRCUCON codes. However, reviews of the content in drums of combustible waste generated during heat source assembly at Los Alamos showed the amount of {sup 238}Pu is typically much greater than 45 milligrams. It is not feasible to appreciably reduce Los Alamos {sup 238}Pu waste drum loadings without significantly increasing waste volumes or introducing unsafe practices. To address this concern, a series of studies were implemented to evaluate the applicability of the TRUCON limits for storage of this specific waste. Addressed in these evaluations were determination of the hydrogen generation rate, hydrogen diffusion rates through confinement layers and vent filters, and packaging requirements specific to Los Alamos generated {sup 238}Pu contaminated combustible waste. These studies also showed that the multiple-layer packaging practices in use at Los Alamos could be relaxed without significantly increasing the risk of contamination. Based on a model developed to predict H{sub 2} concentrations in packages and drum headspace, the site specific effective hydrogen generation rate, and hydrogen-diffusion values, and revising the waste packaging practices, we were able to raise the safe loading limit for {sup 238}Pu waste drums for on site storage to the gram levels typical of currently generated {sup 238}Pu waste.

  1. Fire protection guide for solid waste metal drum storage

    SciTech Connect

    Bucci, H.M.

    1996-09-16

    This guide provides a method to assess potential fire development in drum storage facilities. The mechanism of fire propagation/spread through stored drum arrays is a complex process. It involves flame heat transfer, transient conduction,convection, and radiation between drums (stored in an array configuration). There are several phenomena which may occur when drums are exposed to fire. The most dramatic is violent lid failure which results in total lid removal. When a drum loses its lid due to fire exposure, some or all of the contents may be ejected from the drum, and both the ejected combustible material and the combustible contents remaining within the container will burn. The scope of this guide is limited to storage arrays of steel drums containing combustible (primarily Class A) and noncombustible contents. Class B combustibles may be included in small amounts as free liquid within the solid waste contents.Storage arrays, which are anticipated in this guide, include single or multi-tier palletized (steel or wood pallets) drums,high rack storage of drums, and stacked arrays of drums where plywood sheets are used between tiers. The purpose of this guide is to describe a simple methodology that estimates the consequences of a fire in drum storage arrays. The extent of fire development and the resulting heat release rates can be estimated. Release fractions applicable to this type of storage are not addressed, and the transport of contaminants away from the source is not addressed. However, such assessments require the amount of combustible material consumed and the surface area of this burning material. The methods included in this guide do provide this information.

  2. Acceptable Knowledge Summary Report for Waste Stream: SR-T001-221F-HET/Drums

    SciTech Connect

    Lunsford, G.F.

    1999-08-23

    Since beginning operations in 1954, the Department of Energy's Savannah River Site FB-Line conducted atomic energy defense activities consistent with the listing in Section 10101(3) of the Nuclear Waste Policy Act of 1982. The facility mission was to process and convert dilute plutonium solution into highly purified weapons grade plutonium metal. As a result of various activities conducted in support of the mission (e.g., operation, maintenance, repair, clean up, and facility modifications), the facility generated transuranic waste. This document, along with referenced supporting documents, provides a defensible and auditable record of acceptable knowledge for one of the waste streams from the FB-Line. The waste was packaged in 55-gallon drums, then shipped to the transuranic waste storage facility in ''E'' area of the Savannah River Site. This acceptable knowledge report includes information relating to the facility's history, configuration,equipment, process operations, and waste management practices.

  3. Drum lid removal tool

    DOEpatents

    Pella, Bernard M.; Smith, Philip D.

    2010-08-24

    A tool for removing the lid of a metal drum wherein the lid is clamped over the drum rim without protruding edges, the tool having an elongated handle with a blade carried by an angularly positioned holder affixed to the midsection of the handle, the blade being of selected width to slice between lid lip and the drum rim and, when the blade is so positioned, upward motion of the blade handle will cause the blade to pry the lip from the rim and allow the lid to be removed.

  4. Design of benign matrix drums for the non-destructive assay performance demonstration program for the National TRU Program

    SciTech Connect

    Becker, G.K.

    1996-09-01

    Regulatory compliance programs associated with the Department of Energy (DOE) Waste Isolation Pilot Plant (WIPP) Transuranic (TRU) Waste Characterization Program (the Program) require the collection of waste characterization data of known quality to support repository performance assessment, permitting, and associated activities. Blind audit samples, referred to as PDP (performance demonstration program) samples, are devices used in the NDA PDP program to acquire waste NDA system performance data per defined measurement routines. As defined under the current NDA PDP Program Plan, a PDP sample consists of a DOT 17C 55-gallon PDP matrix drum configured with insertable radioactive standards, working reference materials (WRMs). The particular manner in which the matrix drum and PDP standard(s) are combined is a function of the waste NDA system performance test objectives of a given cycle. The scope of this document is confined to the design of the PDP drum radioactive standard internal support structure, the matrix type and the as installed configuration. The term benign is used to designate a matrix possessing properties which are nominally non-interfering to waste NDA measurement techniques. Measurement interference sources are technique specific but include attributes such as: high matrix density, heterogeneous matrix distributions, matrix compositions containing high moderator/high Z element concentrations, etc. To the extent practicable the matrix drum design should not unduly bias one NDA modality over another due to the manner in which the matrix drum configuration manifests itself to the measurement system. To this end the PDP matrix drum configuration and composition detailed below is driven primarily by the intent to minimize the incorporation of matrix attributes known to interfere with fundamental waste NDA modalities, i.e. neutron and gamma based techniques.

  5. Thermal sensing for characterizing the contents of waste storage drums

    NASA Technical Reports Server (NTRS)

    Philpot, W. D.; Philipson, W. R.

    1985-01-01

    The present investigation is concerned with the feasibility to employ remote sensing for the characterization of the contents of liquid chemical waste storage drums. Philipson et al. (1981) had found that, when the air temperature is changing rapidly, differences in the thermal inertia of the drum contents can lead to detectable differences in the skin temperature of the drums. Thus, postsunset, airborne thermal remote sensing could potentially provide some level of discrimination among chemical storage drums. Discrimination should be possible among steel drums filled largely with: (1) aqueous solvents, (2) organic solvents, or (3) clay packing materials. The response of a drum filled with clay packing materials should be similar to that of an empty drum. The reported study had the objective to verify the theoretical findings, taking into account the use of a hand-held infrared radiometer. It was found that under the proper conditions the temperature differences among drums with the three different types of contents will be significant and consistent.

  6. Impact of Different Standard Type A7A Drum Closure-Ring Practices on Gasket Contraction and Bolt Closure Distance– 15621

    SciTech Connect

    Ketusky, Edward; Blanton, Paul; Bobbitt, John H.

    2015-03-11

    The Department of Energy, the Savannah River National Laboratory, several manufacturers of specification drums, and the United States Department of Transportation (DOT) are collaborating in the development of a guidance document for DOE contractors and vendors who wish to qualify containers to DOT 7A Type A requirements. Currently, the effort is focused on DOT 7A Type A 208-liter (55-gallons) drums with a standard 12-gauge bolted closure ring. The U.S. requirements, contained in Title 49, Part 178.350 “Specification 7A; general packaging, Type A specifies a competent authority review of the packaging is not required for the transport of (Class 7) radioactive material containing less than Type A quantities of radioactive material. For Type AF drums, a 4 ft. regulatory free drop must be performed, such that the drum “suffers maximum damage.” Although the actual orientation is not defined by the specification, recent studies suggest that maximum damage would result from a shallow angle top impact, where kinetic energy is transferred to the lid, ultimately causing heavy damage to the lid, or even worse, causing the lid to come off. Since each vendor develops closure recommendations/procedures for the drums they manufacture, key parameters applied to drums during closing vary based on vendor. As part of the initial phase of the collaboration, the impact of the closure variants on the ability of the drum to suffer maximum damage is investigated. Specifically, closure testing is performed varying: 1) the amount of torque applied to the closure ring bolt; and, 2) stress relief protocol, including: a) weight of hammer; and, b) orientation that the hammer hits the closure ring. After closure, the amount of drum lid gasket contraction and the distance that the closure bolt moves through the closure ring is measured.

  7. Final environmental assessment: TRU waste drum staging building, Technical Area 55, Los Alamos National Laboratory

    SciTech Connect

    1996-02-09

    Much of the US Department of Energy`s (DOE`s) research on plutonium metallurgy and plutonium processing is performed at Los Alamos National Laboratory (LANL), in Los Alamos, New Mexico. LANL`s main facility for plutonium research is the Plutonium Facility, also referred to as Technical Area 55 (TA-55). The main laboratory building for plutonium work within the Plutonium Facility (TA-55) is the Plutonium Facility Building 4, or PF-4. This Environmental Assessment (EA) analyzes the potential environmental effects that would be expected to occur if DOE were to stage sealed containers of transuranic (TRU) and TRU mixed waste in a support building at the Plutonium Facility (TA-55) that is adjacent to PF-4. At present, the waste containers are staged in the basement of PF-4. The proposed project is to convert an existing support structure (Building 185), a prefabricated metal building on a concrete foundation, and operate it as a temporary staging facility for sealed containers of solid TRU and TRU mixed waste. The TRU and TRU mixed wastes would be contained in sealed 55-gallon drums and standard waste boxes as they await approval to be transported to TA-54. The containers would then be transported to a longer term TRU waste storage area at TA-54. The TRU wastes are generated from plutonium operations carried out in PF-4. The drum staging building would also be used to store and prepare for use new, empty TRU waste containers.

  8. Rotating drum filter

    DOEpatents

    Anson, Donald

    1990-01-01

    A perforated drum (10) rotates in a coaxial cylindrical housing (18) having three circumferential ports (19,22,23), and an axial outlet (24) at one end. The axis (11) is horizontal. A fibrous filter medium (20) is fed through a port (19) on or near the top of the housing (81) by a distributing mechanism (36) which lays a uniform mat (26) of the desired thickness onto the rotating drum (10). This mat (26) is carried by the drum (10) to a second port (23) through which dirty fluid (13) enters. The fluid (13) passes through the filter (26) and the cleaned stream (16) exits through the open end (15) of the drum (10) and the axial port (24) in the housing (18). The dirty filter material (20) is carried on to a third port (22) near the bottom of the housing (18) and drops into a receiver (31) from which it is continuously removed, cleaned (30), and returned (32) to the charging port (36) at the top. To support the filter mat, the perforated cylinder may carry a series of tines (40), shaped blades (41), or pockets, so that the mat (26) will not fall from the drum (10) prematurely. To minimize risk of mat failure, the fluid inlet port (23) may be located above the horizontal centerline (11).

  9. Degradation of transuranic waste drums in underground storage

    SciTech Connect

    Duncan, D.; DeRosa, D.C.; Demiter, J.A.

    1995-12-31

    The Hanford site is one of several U.S. Department of Energy locations that has transuranic radioactive Waste in storage, resulting from nuclear weapons material production. Transuranic waste has extremely long-lived radionuclides requiring great care in management; such waste is slated for eventual disposal in the Waste Isolation Pilot Plant in New Mexico. Most of this waste is stored in 208-{ell} (55-gal) drums below ground. At the Hanford site 37 641 drums are stored in several trenches. The drums were stacked up to five high with plywood sheeting between the layers and on top of the stacks. Plastic tarps were used to cover the drums and the plywood, with several feet of earth backfilled on top of the plastic. A fraction of the drums ({approximately}20%) were covered only with earth, not with plywood and plastic. The drums are either painted low-carbon steel or galvanized low-carbon steel. They have been placed in storage from 1970 to 1988, resulting in between 7 and 25 yr of storage. The environment is either soil or air atmosphere. The air atmosphere environment also includes, for some drum surfaces, contact with the underside of the tarp. The temperature of the air atmosphere is relatively uniform. Year-round measurements have not been taken, but available data suggest that the temperature span should be from {approximately} 10 to 30{degrees}C (50 to 86{degrees}F). Humidity in underground storage module mock-ups has been measured at nearly 90% during testing in the summer months. Subsequent tests have shown that the humidity probably drops to 50 to 60% during other seasons. This report describes results of a project to inspect the condition of the waste drums.

  10. Neutron Screening Measurements of 110 gallon drums at T Plant

    SciTech Connect

    Mozhayev, Andrey V.; Hilliard, James R.; Berg, Randal K.

    2011-01-14

    The Pacific Northwest National Laboratory (PNNL) Nondestructive Assay (NDA) Service Center was contracted to develop and demonstrate a simple and inexpensive method of assaying 110 gallon drums at the Hanford Site’s T-Plant. The drums contained pucks of crushed old drums used for storage of transuranic (TRU) waste. The drums were to be assayed to determine if they meet the criteria for TRU or Low Level Waste (LLW). Because of the dense matrix (crushed steel drums) gamma measurement techniques were excluded and a mobile, configurable neutron system, consisting of four sequentially connected slab detectors was chosen to be used for this application. An optimum measurement configuration was determined through multiple test measurements with californium source. Based on these measurements the initial calibration of the system was performed applying the isotopic composition for aged weapon-grade plutonium. A series of background and blank puck drum measurements allowed estimating detection limits for both total (singles) and coincidence (doubles) counting techniques. It was found that even conservative estimates for minimum detection concentration using singles count rate were lower than the essential threshold of 100 nCi/g. Whereas the detection limit of coincidence counting appeared to be about as twice as high of the threshold. A series of measurements intended to verify the technique and revise the initial calibration obtained were performed at the Waste Receiving and Processing (WRAP) facility with plutonium standards. Standards with a total mass of 0.3 g of plutonium (which is estimated to be equivalent of 100 nCi/g for net waste weight of 300 kg) loaded in the test puck drum were clearly detected. The following measurements of higher plutonium loadings verified the calibration factors obtained in the initial exercise. The revised and established calibration factors were also confirmed within established uncertainties by additional measurements of plutonium

  11. Clamshell closure for metal drum

    SciTech Connect

    Blanton, Paul S

    2014-09-30

    Closure ring to retain a lid in contact with a metal drum in central C-section conforming to the contact area between a lid and the rim of a drum and further having a radially inwardly directed flange and a vertically downwardly directed flange attached to the opposite ends of the C-section. The additional flanges reinforce the top of the drum by reducing deformation when the drum is dropped and maintain the lid in contact with the drum. The invention is particularly valuable in transportation and storage of fissile material.

  12. Characterization of In-Drum Drying Products

    SciTech Connect

    Kroselj, V.; Jankovic, M.; Skanata, D.; Medakovic, S.; Harapin, D.; Hertl, B.

    2006-07-01

    A few years ago Krsko NPP decided to introduce In-Drum Drying technology for treatment and conditioning of evaporator concentrates and spent ion resins. The main reason to employ this technology was the need for waste volume reduction and experience with vermiculite-cement solidification that proved inadequate for Krsko NPP. Use of In-Drum Drying technology was encouraged by good experience in the field at some German and Spanish NPP's. In the paper, solidification techniques in vermiculite-cement matrix and In-Drum Drying System are described briefly. The resulting waste forms (so called solidification and dryer products) and containers that are used for interim storage of these wastes are described as well. A comparison of the drying versus solidification technology is performed and advantages as well as disadvantages are underlined. Experience gained during seven years of system operation has shown that crying technology resulted in volume reduction by factor of 20 for evaporator concentrates, and by factor of 5 for spent ion resin. Special consideration is paid to the characterization of dryer products. For evaporator concentrates the resulting waste form is a solid salt block with up to 5% bound water. It is packaged in stainless steel drums (net volume of 200 l) with bolted lids and lifting rings. The fluidized spent ion resins (primary and blow-down) are sluiced into the spent resin drying tank. The resin is dewatered and dried by electrical jacket heaters. The resulting waste (i.e. fine granulates) is directly discharged into a shielded stainless steel drum with bolted lid and lifting rings. Characterization of both waste forms has been performed in accordance with recommendations given in Characterization of Radioactive Waste Forms and Packages issued by International Atomic Energy Agency, 1997. This means that radiological, chemical, physical, mechanical, biological and thermal properties of the waste form has been taken into consideration. In the paper

  13. Drum cutter mining machine

    SciTech Connect

    Oberste-beulmann, K.; Schupphaus, H.

    1980-02-19

    A drum cutter mining machine includes a machine frame with a winch having a drive wheel to engage a rack or chain which extends along the path of travel by the mining machine to propel the machine along a mine face. The mining machine is made up of discrete units which include a machine body and machine housings joined to opposite sides of the machine body. The winch is either coupled through a drive train with a feed drive motor or coupled to the drive motor for cutter drums. The machine housings each support a pivot shaft coupled by an arm to a drum cutter. One of these housings includes a removable end cover and a recess adapted to receive a support housing for a spur gear system used to transmit torque from a feed drive motor to a reduction gear system which is, in turn, coupled to the drive wheel of the winch. In one embodiment, a removable end cover on the machine housing provides access to the feed drive motor. The feed drive motor is arranged so that the rotational axis of its drive output shaft extends transversely to the stow side of the machine frame. In another embodiment, the reduction gear system is arranged at one side of the pivot shaft for the cutter drum while the drive motor therefor is arranged at the other side of the pivot shaft and coupled thereto through the spur gear system. In a further embodiment, the reduction gear system is disposed between the feed motor and the pivot shaft.

  14. Superior Barrel & Drum, Elk Township, New Jersey

    EPA Pesticide Factsheets

    The Superior Barrel and Drum Superfund site is a 5.5-acre property located in Elk Township, Gloucester County, New Jersey. Superior Barrel and Drum is listed as a drum reconditioning business. These facilities typically clean and recondition metal

  15. WDC - Advanced system for characterization of {alpha}-bearing waste in 200 l and 400 l drums: performances and lessons learned from the first industrial measurement campaigns

    SciTech Connect

    Libens, A.; Vandorpe, M.; Cuchet, J.M.

    2007-07-01

    The Waste Drum Characterization installation was originally developed for the assay of alpha-bearing waste in standard 200 1 (55 gallons) drums during the dismantling operations of the Siemens mixed-oxide (MOX) facility in Hanau (Germany). That installation was validated and qualified by the German authorities, its main performances being: - Counting efficiency for coincident neutrons: approx. 1%; Lowest Limit of Detection (LLD): 75 mg {sup 240}Pu{sub eq}; Pu content per drum: up to 100 g tot. (35 g {sup 240}Pu{sub eq}) - Measurement duration: approx. 20 minutes. The success of this system, a passive neutron coincidence counter combined with a high resolution gamma spectrometer, led to the radiological characterization and qualification of about 1,700 drums during the period 2001 - 2004. In 2005, after completion of the dismantling operations of the Siemens MOX facility, Tecnubel took over the WDC installation which could be used in the frame of the future dismantling of the Belgonucleaire's MOX plant in Dessel (Belgium), which can be comparable to the Siemen's one. This second (and new) life for the WDC means that it must be rigorously retested and validated against the Belgian authorities requirements. Furthermore, and additionally to the future use in the Belgonucleaire's facility, Tecnubel was faced with new challenges, namely: Assay of 400 l drums together with the 200 l packages; Determination of the real LLD taking into account the background in different Belgian nuclear facilities, the determination of a value of {approx}5 mg {sup 240}Pu{sub eq} being an objective; - Assay of mixed alpha/beta-gamma wastes; Transportability of the WDC from one plant to another; Assistance to different nuclear operators for the licensing of the WDC for their own waste types. This paper describes the installation itself and its performances, presents the difficulties encountered during the new challenge and the results of the performed revalidation tests; it gives the

  16. Anisotropy in rotating drums

    NASA Astrophysics Data System (ADS)

    Povall, Timothy; McBride, Andrew; Govender, Indresan

    2015-11-01

    An anisotropic relationship between the stress and the strain rate has been observed in two-dimensional simulations of rotating drums. The objective of this work is to investigate the structure of the constitutive relation using three-dimensional discrete-element-method simulations of a rotating drum containing identical rigid spheres for a range of rotational speeds. Anisotropy is quantified from the alignment of the stress and strain rate tensors, with the strain rate computed using a least-squares fit. It is shown that in certain regions there is a strong anisotropic relationship, regardless of the speed of rotation. The effective friction coefficient is examined in order to determine the phase space in which the μ (I) rheology is valid. Lastly, a depth-averaged approach through the flowing layer is employed to determine the relationship between the velocity tangential to the equilibrium surface and the height of the flowing layer. A power-law relationship that approaches linear at high speeds is observed. Supported by NRF/DST Scarce Skills (South Africa).

  17. Miniature rotating transmissive optical drum scanner

    NASA Technical Reports Server (NTRS)

    Lewis, Robert (Inventor); Parrington, Lawrence (Inventor); Rutberg, Michael (Inventor)

    2013-01-01

    A miniature rotating transmissive optical scanner system employs a drum of small size having an interior defined by a circumferential wall rotatable on a drum axis, an optical element positioned within the interior of the drum, and a light-transmissive lens aperture provided at an angular position in the circumferential wall of the drum for scanning a light beam to or from the optical element in the drum along a beam azimuth angle as the drum is rotated. The miniature optical drum scanner configuration obtains a wide scanning field-of-view (FOV) and large effective aperture is achieved within a physically small size.

  18. Drum inspection robots: Application development

    SciTech Connect

    Hazen, F.B.; Warner, R.D.

    1996-02-01

    Throughout the Department of Energy (DOE), drums containing mixed and low level stored waste are inspected, as mandated by the Resource Conservation and Recovery Act (RCRA) and other regulations. The inspections are intended to prevent leaks by finding corrosion long before the drums are breached. The DOE Office of Science and Technology (OST) has sponsored efforts towards the development of robotic drum inspectors. This emerging application for mobile and remote sensing has broad applicability for DOE and commercial waste storage areas. Three full scale robot prototypes have been under development, and another project has prototyped a novel technique to analyze robotically collected drum images. In general, the robots consist of a mobile, self-navigating base vehicle, outfitted with sensor packages so that rust and other corrosion cues can be automatically identified. They promise the potential to lower radiation dose and operator effort required, while improving diligence, consistency, and documentation.

  19. Drum tie-down apparatus

    DOEpatents

    Morse, H.E.

    A drum tie-down apparatus for securing drum-like containers in an upright position to a floor or platform of a transportation vehicle having spaced apart cargo tie-down points. The apparatus comprises a pair of cylindrical, hollow tube segments horizontally oriented and engageable with a drum lid adjacent opposite rim edges, flexible strap segments for connecting upper and lower central portions of the tube segments together across the drum lid and a pair of elongated flexible tie-down segments, one extending horizontally through each of the tube segments, the ends thereof being attached to said spaced apart tie-down points such that end portions of the pair of tie-down segments extend downwardly and radially outwardly from the tube segments to the tie-down points.

  20. Drum tie-down apparatus

    DOEpatents

    Morse, Harvey E.

    1984-01-01

    A drum tie-down apparatus for securing drum-like containers in an upright position to a floor or platform of a transportation vehicle having spaced apart cargo tie-down points. The apparatus comprises a pair of cylindrical, hollow tube segments horizontally oriented and engageable with a drum lid adjacent opposite rim edges, flexible strap segments for connecting upper and lower central portions of the tube segments together across the drum lid and a pair of elongated flexible tie-down segments, one extending horizontally through each of the tube segments, the ends thereof being attached to said spaced apart tie-down points such that end portions of the pair of tie-down segments extend downwardly and radially outwardly from the tube segments to the tie-down points.

  1. Acceptable Knowledge Summary Report for Waste Stream: SR-T001-221F-HET/Drums

    SciTech Connect

    Lunsford, G.F.

    1998-10-26

    Since beginning operations in 1954, the Savannah River Site FB-Line produced Weapons Grade Plutonium for the United States National Defense Program. The facility mission was mainly to process dilute plutonium solution received from the 221-F Canyon into highly purified plutonium metal. As a result of various activities (maintenance, repair, clean up, etc.) in support of the mission, the facility generated a transuranic heterogeneous debris waste stream. Prior to January 25, 1990, the waste stream was considered suspect mixed transuranic waste (based on potential for inclusion of F-Listed solvent rags/wipes) and is not included in this characterization. Beginning January 25, 1990, Savannah River Site began segregation of rags and wipes containing F-Listed solvents thus creating a mixed transuranic waste stream and a non-mixed transuranic waste stream. This characterization addresses the non-mixed transuranic waste stream packaged in 55-gallon drums after January 25, 1990.Characterization of the waste stream was achieved using knowledge of process operations, facility safety basis documentation, facility specific waste management procedures and storage / disposal records. The report is fully responsive to the requirements of Section 4.0 "Acceptable Knowledge" from the WIPP Transuranic Waste Characterization Quality Assurance Plan, CAO-94-1010, and provides a sound, (and auditable) characterization that satisfies the WIPP criteria for Acceptable Knowledge.

  2. Hand-Drumming to Build Community: The Story of the Whittier Drum Project

    ERIC Educational Resources Information Center

    Stone, Nathan Neil

    2005-01-01

    In this article the author shares the story of the Whittier Drum Project and how it succeeded. The Whittier Drum Project has brought the community together through the talents of youth and their dedication to drumming, and has used drumming to link professionals to their own communities. The author adapted the model to meet the therapeutic needs…

  3. Vapor generator steam drum spray head

    DOEpatents

    Fasnacht, Jr., Floyd A.

    1978-07-18

    A typical embodiment of the invention provides a combination feedwater and "cooldown" water spray head that is centrally disposed in the lower portion of a nuclear power plant steam drum. This structure not only discharges the feedwater in the hottest part of the steam drum, but also increases the time required for the feedwater to reach the steam drum shell, thereby further increasing the feedwater temperature before it contacts the shell surface, thus reducing thermal shock to the steam drum structure.

  4. MCNP Modeling Results for Location of Buried TRU Waste Drums

    NASA Astrophysics Data System (ADS)

    Steinman, D. K.; Schweitzer, J. S.

    2006-05-01

    In the 1960's, fifty-five gallon drums of TRU waste were buried in shallow pits on remote U.S. Government facilities such as the Idaho National Engineering Laboratory (now split into the Idaho National Laboratory and the Idaho Completion Project [ICP]). Subsequently, it was decided to remove the drums and the material that was in them from the burial pits and send the material to the Waste Isolation Pilot Plant in New Mexico. Several technologies have been tried to locate the drums non-intrusively with enough precision to minimize the chance for material to be spread into the environment. One of these technologies is the placement of steel probe holes in the pits into which wireline logging probes can be lowered to measure properties and concentrations of material surrounding the probe holes for evidence of TRU material. There is also a concern that large quantities of volatile organic compounds (VOC) are also present that would contaminate the environment during removal. In 2001, the Idaho National Engineering and Environmental Laboratory (INEEL) built two pulsed neutron wireline logging tools to measure TRU and VOC around the probe holes. The tools are the Prompt Fission Neutron (PFN) and the Pulsed Neutron Gamma (PNG), respectively. They were tested experimentally in surrogate test holes in 2003. The work reported here estimates the performance of the tools using Monte-Carlo modelling prior to field deployment. A MCNP model was constructed by INEEL personnel. It was modified by the authors to assess the ability of the tools to predict quantitatively the position and concentration of TRU and VOC materials disposed around the probe holes. The model was used to simulate the tools scanning the probe holes vertically in five centimetre increments. A drum was included in the model that could be placed near the probe hole and at other locations out to forty-five centimetres from the probe-hole in five centimetre increments. Scans were performed with no chlorine in the

  5. 5. MOTOR/WINCH DRUM ASSEMBLY FOR OXYGEN LANCE HOISTING RIG ON ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    5. MOTOR/WINCH DRUM ASSEMBLY FOR OXYGEN LANCE HOISTING RIG ON THE WEIGHING FLOOR OF THE FURNACE AISLE IN THE BOP SHOP LOOKING SOUTHEAST. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

  6. Re-evaluation of the 1995 Hanford Large Scale Drum Fire Test Results

    SciTech Connect

    Yang, J M

    2007-05-02

    A large-scale drum performance test was conducted at the Hanford Site in June 1995, in which over one hundred (100) 55-gal drums in each of two storage configurations were subjected to severe fuel pool fires. The two storage configurations in the test were pallet storage and rack storage. The description and results of the large-scale drum test at the Hanford Site were reported in WHC-SD-WM-TRP-246, ''Solid Waste Drum Array Fire Performance,'' Rev. 0, 1995. This was one of the main references used to develop the analytical methodology to predict drum failures in WHC-SD-SQA-ANAL-501, 'Fire Protection Guide for Waste Drum Storage Array,'' September 1996. Three drum failure modes were observed from the test reported in WHC-SD-WM-TRP-246. They consisted of seal failure, lid warping, and catastrophic lid ejection. There was no discernible failure criterion that distinguished one failure mode from another. Hence, all three failure modes were treated equally for the purpose of determining the number of failed drums. General observations from the results of the test are as follows: {lg_bullet} Trash expulsion was negligible. {lg_bullet} Flame impingement was identified as the main cause for failure. {lg_bullet} The range of drum temperatures at failure was 600 C to 800 C. This is above the yield strength temperature for steel, approximately 540 C (1,000 F). {lg_bullet} The critical heat flux required for failure is above 45 kW/m{sup 2}. {lg_bullet} Fire propagation from one drum to the next was not observed. The statistical evaluation of the test results using, for example, the student's t-distribution, will demonstrate that the failure criteria for TRU waste drums currently employed at nuclear facilities are very conservative relative to the large-scale test results. Hence, the safety analysis utilizing the general criteria described in the five bullets above will lead to a technically robust and defensible product that bounds the potential consequences from postulated

  7. Fort Drum Miscellaneous Building Survey

    DTIC Science & Technology

    2008-02-01

    ER D C/ CE R L SR -0 8 -2 Fort Drum Miscellaneous Building Survey Adam Smith and Sunny Stone February 2008 C on st ru ct io n E n...Miscellaneous Building Survey Adam Smith and Sunny Stone Construction Engineering Research Laboratory United States Army Engineer Research and...CERL). The CERL Project Manager was Mr. Adam Smith . Dr. Christopher White is Chief, CEERD-CN-C, and Dr. John Bandy is Chief, CEERD-CN. The Director

  8. 49 CFR 178.508 - Standards for fiber drums.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Standards for fiber drums. 178.508 Section 178.508...-Oriented Packaging Standards § 178.508 Standards for fiber drums. (a) The identification code for a fiber drum is 1G. (b) Construction requirements for fiber drums are as follows: (1) The body of the drum...

  9. Rolling, Sliding and Mixing of a 2D Granular Media in a Thin Vertical Drum

    NASA Astrophysics Data System (ADS)

    Kolsky, Daniel; Galbreath, Ashford; Olafsen, Jeffrey S.

    2000-11-01

    Even for a relatively small number of particles, interactions of collision and friction complicate the understanding of the dynamics in granular flows. A rich assortment of interesting dynamics is exhibited in a 2D experiment of stainless steel disks contained in a rotating, thin, vertical drum. Analysis of high-speed and high-resolution photography reveals various distributions of translational and rotational kinetic energy within the granular flow as the number of particles in the drum is increased. A detailed examination of the collective behavior in this experiment is important for understanding mixing in granular flows.

  10. 30 CFR 77.1436 - Drum end attachment.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Hoisting Wire Ropes § 77.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached... professional engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope...

  11. 30 CFR 77.1436 - Drum end attachment.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Hoisting Wire Ropes § 77.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached... professional engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope...

  12. 30 CFR 77.1436 - Drum end attachment.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Hoisting Wire Ropes § 77.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached... professional engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope...

  13. 30 CFR 77.1436 - Drum end attachment.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Hoisting Wire Ropes § 77.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached... professional engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope...

  14. 30 CFR 77.1436 - Drum end attachment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Hoisting Wire Ropes § 77.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached... professional engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope...

  15. 13. Detail view of drum screen short shaft gears, journal ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    13. Detail view of drum screen short shaft gears, journal bearing, rotation drive chain, upper sprocket gear, and drum screen edge in background, facing southeast (downstream) from drum screen cover. - Congdon Canal, Fish Screen, Naches River, Yakima, Yakima County, WA

  16. Fort Drum integrated resource assessment

    SciTech Connect

    Dixon, D.R.; Armstrong, P.R.; Brodrick, J.R.; Daellenbach, K.K.; Di Massa, F.V.; Keller, J.M.; Richman, E.E.; Sullivan, G.P.; Wahlstrom, R.R.

    1992-12-01

    The US Army Forces Command (FORSCOM) has tasked the Pacific Northwest Laboratory (PNL) as the lead laboratory supporting the US Department of Energy (DOE) Federal Energy Management Program's mission to identify, evaluate, and assist in acquiring all cost-effective energy projects at Fort Drum. This is a model program PNL is designing for federal customers served by the Niagara Mohawk Power Company. It will identify and evaluate all electric and fossil fuel cost-effective energy projects; develop a schedule at each installation for project acquisition considering project type, size, timing, and capital requirements, as well as energy and dollar savings; and secure 100% of the financing required to implement electric energy efficiency projects from Niagara Mohawk and have Niagara Mohawk procure the necessary contractors to perform detailed audits and install the technologies. This report documents the assessment of baseline energy use at one of Niagara Mohawk's primary federal facilities, the FORSCOM Fort Drum facility located near Watertown, New York. It is a companion report to Volume 1, the Executive Summary, and Volume 3, the Resource Assessment. This analysis examines the characteristics of electric, gas, oil, propane, coal, and purchased thermal capacity use for fiscal year (FY) 1990. It records energy-use intensities for the facilities at Fort Drum by building type and energy end use. It also breaks down building energy consumption by fuel type, energy end use, and building type. A complete energy consumption reconciliation is presented that includes the accounting of all energy use among buildings, utilities, central systems, and applicable losses.

  17. Hand-drumming to build community: the story of the Whittier Drum Project.

    PubMed

    Stone, Nathan Neil

    2005-01-01

    Over the years, the author participated in drum circles and classes in Denver, Fort Collins, and Boulder, Colorado. He noticed that drumming made him feel grounded and at peace. Drumming is very accessible, not like playing the piano or violin. Simple rhythms can be taught to people with no drumming experience very quickly and an ensemble rhythm created with a group in one sitting. Drumming turned out to be a highly effective way to engage with young people not only to address their individual spirits but to join with others to create a community.

  18. Drum plug piercing and sampling device and method

    DOEpatents

    Counts, Kevin T.

    2011-04-26

    An apparatus and method for piercing a drum plug of a drum in order to sample and/or vent gases that may accumulate in a space of the drum is provided. The drum is not damaged and can be reused since the pierced drum plug can be subsequently replaced. The apparatus includes a frame that is configured for engagement with the drum. A cylinder actuated by a fluid is mounted to the frame. A piercer is placed into communication with the cylinder so that actuation of the cylinder causes the piercer to move in a linear direction so that the piercer may puncture the drum plug of the drum.

  19. Comparison of Conventional Sprocket Drum and Sprocket Drum with Modified Design

    NASA Astrophysics Data System (ADS)

    Sobota, Piotr

    2016-09-01

    Seats in conventional sprocket drums are symmetrical. Due to the set general direction of sprocket drum revolutions resulting from the direction of rock transport, the wear of the seat bottoms and teeth flanks may be reduced by introducing the asymmetry of the profile of the sprocket drum seats. The proposed modification of sprocket drum seats' profile consists of inclining the seat bottom towards the expected direction of the basic drum revolutions. The work compares the loads on the seats and teeth of a conventional drum with its profile conforming to the standard to a modified drum with an asymmetric profile of seats. For the general direction of sprocket drum revolutions, the maximum values of all forces are higher for a standard drum than for a modified drum. The profile asymmetry substantially shortens the friction path of the horizontal link front torus on the seat bottom and relative total friction work on the seat bottom and lessens the occurrence probability of the slide of the horizontal link rear torus on the tooth flank. The modification of the profile causes also the asymmetric wear of link joints. The total relative friction work is considerably reduced in the front joint as compared to a conventional drum, and the total relative friction work in the rear joint is increasing at the same time.

  20. Environmental policy -- A leaking drum?

    SciTech Connect

    Bishop, J.

    1995-07-01

    Twenty years ago, the US had virtually no overall environmental policy. Since then, one has evolved as a result of accumulated legislation, much of which was crafted in reaction to specific events, typically real or potential disasters. The familiar names of Love Canal, Times Beach, Bhopal and others are the symbolic anchor points of that evolution, which yielded Superfund, the Resource Conservation and Recovery Act, the Superfund Amendments and Reauthorization Act, and other environmental statutes. The laws in each case were developed in response to particular environmental and health issues--clean water for drinking and recreation, unpolluted air, safe production of chemicals and chemical-based products. The result was a growing body of environmental legislation that eventually became an accumulate of requirements lacking internal consistency or coherence. Because policymaking followed, rather than guided, legislative actions, the policy itself became inconsistent and sometimes illogical. Like a drum that gradually and indiscriminately is filled with a mixture of mutually reactive chemicals, environmental policy increasingly became a volatile source of concern for those industries in whose midst it had been placed. Lately, there is growing consensus that the drum not only has been overfilled, it also is leaking.

  1. FIFTY-FIVE GALLON DRUM STANDARD STUDY

    SciTech Connect

    PUIGH RJ

    2009-05-14

    Fifty-five gallon drums are routinely used within the U.S. for the storage and eventual disposal of fissionable materials as Transuranic or low-level waste. To support these operations, criticality safety evaluations are required. A questionnaire was developed and sent to selected Endusers at Hanford, Idaho National Laboratory, Lawrence Livermore National Laboratory, Oak Ridge and the Savannah River Site to solicit current practices. This questionnaire was used to gather information on the kinds of fissionable materials packaged into drums, the models used in performing criticality safety evaluations in support of operations involving these drums, and the limits and controls established for the handling and storage of these drums. The completed questionnaires were reviewed and clarifications solicited through individual communications with each Enduser to obtain more complete and consistent responses. All five sites have similar drum operations involving thousands to tens of thousands of fissionable material waste drums. The primary sources for these drums are legacy (prior operations) and decontamination and decommissioning wastes at all sites except Lawrence Livermore National Laboratory. The results from this survey and our review are discussed in this paper.

  2. Energy expenditure in rock/pop drumming.

    PubMed

    De La Rue, S E; Draper, S B; Potter, C R; Smith, M S

    2013-10-01

    Despite the vigorous nature of rock/pop drumming, there are no precise data on the energy expenditure of this activity. The aim of this study was to quantify the energy cost of rock/pop drumming. Fourteen male drummers (mean±SD; age 27±8 yrs.) completed an incremental drumming test to establish the relationship between energy expenditure and heart rate for this activity and a ramped cycle ergometer test to exhaustion as a criterion measure for peak values (oxygen uptake and heart rate). During live concert performance heart rate was continuously measured and used to estimate energy expenditure (from the energy expenditure vs. heart rate data derived from the drumming test). During concert performance, estimated energy expenditure (mean±SD) was 623±168 kcal.h⁻¹ (8.1±2.2 METs) during performances of 38.6±15.6 min, and drummers achieved a peak heart rate of 186±16 b.min⁻¹. During the drumming test participants attained 78.7±8.3% of the cycle ergometer peak oxygen uptake. Rock/pop drumming represents a relatively high-intensity form of physical activity and as such involves significant energy expenditure. Rock/pop drumming should be considered as a viable alternative to more traditional forms of physical activity.

  3. 29 CFR 1915.173 - Drums and containers.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Drums and containers. 1915.173 Section 1915.173 Labor... Vessels, Drums and Containers, Other Than Ship's Equipment § 1915.173 Drums and containers. (a) Shipping drums and containers shall not be pressurized to remove their contents. (b) A temporarily...

  4. 49 CFR 178.508 - Standards for fiber drums.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Standards for fiber drums. 178.508 Section 178.508...-bulk Performance-Oriented Packaging Standards § 178.508 Standards for fiber drums. (a) The identification code for a fiber drum is 1G. (b) Construction requirements for fiber drums are as follows: (1)...

  5. 49 CFR 178.505 - Standards for aluminum drums.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Standards for aluminum drums. 178.505 Section 178...-bulk Performance-Oriented Packaging Standards § 178.505 Standards for aluminum drums. (a) The following are the identification codes for aluminum drums: (1) 1B1 for a non-removable head aluminum drum;...

  6. 49 CFR 178.505 - Standards for aluminum drums.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Standards for aluminum drums. 178.505 Section 178...-bulk Performance-Oriented Packaging Standards § 178.505 Standards for aluminum drums. (a) The following are the identification codes for aluminum drums: (1) 1B1 for a non-removable head aluminum drum;...

  7. 49 CFR 178.505 - Standards for aluminum drums.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Standards for aluminum drums. 178.505 Section 178...-bulk Performance-Oriented Packaging Standards § 178.505 Standards for aluminum drums. (a) The following are the identification codes for aluminum drums: (1) 1B1 for a non-removable head aluminum drum;...

  8. 49 CFR 178.505 - Standards for aluminum drums.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Standards for aluminum drums. 178.505 Section 178...-bulk Performance-Oriented Packaging Standards § 178.505 Standards for aluminum drums. (a) The following are the identification codes for aluminum drums: (1) 1B1 for a non-removable head aluminum drum;...

  9. 52. EXTERIOR DETAIL VIEW OF A SPARE DRUM FOR A ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    52. EXTERIOR DETAIL VIEW OF A SPARE DRUM FOR A FRENIER PUMP. THE CHARCOAL HOUSE IS IN THE BACKGROUND AND THE DRUM LEANING AGAINST THE EAST SIDE OF THE MILL ANNEX. NOTE THE WELDS IN THE DRUM, THEY DELINEATE THE SPIRAL LEADING TO THE CENTER OF THE DRUM. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

  10. Over-Pressurized Drums: Their Causes and Mitigation

    SciTech Connect

    Simmons, Fred; Kuntamukkula, Murty; Quigley, David; Robertson, Janeen; Freshwater, David

    2009-07-10

    Having to contend with bulging or over-pressurized drums is, unfortunately, a common event for people storing chemicals and chemical wastes. (Figure 1) The Department of Energy alone reported over 120 incidents of bulging drums between 1992 and 1999 (1). Bulging drums can be caused by many different mechanisms, represent a number of significant hazards and can be tricky to mitigate. In this article, we will discuss reasons or mechanisms by which drums can become over-pressurized, recognition of the hazards associated with and mitigation of over-pressurized drums, and methods that can be used to prevent drum over-pressurization from ever occurring. Drum pressurization can represent a significant safety hazard. Unless recognized and properly mitigated, improperly manipulated pressurized drums can result in employee exposure, employee injury, and environmental contamination. Therefore, recognition of when a drum is pressurized and knowledge of pressurized drum mitigation techniques is essential.

  11. Information Gathering Document 0321-1437-30-R-OG

    SciTech Connect

    Hollister, R

    2009-07-15

    Fines and turnings from machining depleted uranium (Dep-U), natural uranium (Nat-U), and Thorium-232, and stainless steel and aluminum. This IGO allows only small, oxidizable pieces of Dep-U/Nat-U/Th-232, with regulated metal contaminants below regulatory limits. Fines and turnings will be in 30 gallon vented drums immersed in mineral oil. The 30 gallon drums will be overpacked in 55 gallon vented drums. The waste will be stored on site until sent for stabilization & disposal with approved TSOFs.

  12. Fuzzy control of a boiler steam drum

    SciTech Connect

    Mayer, K.; Crockett, W.K.

    1995-10-01

    The authors controlled the inlet water flow to a dynamic model of a steam drum using fuzzy logic. The drum level varied little with step inputs in steam flow. The fuzzy logic controller performed at least as well as a well-tuned traditional PI (which is notoriously difficult to tune). Using plant data in the model provided further evidence that fuzzy logic control gave excellent results. The drum level is a function of inlet water, steam production, and blowdown. To compensate for upsets caused by steam production, independent variables used in the fuzzy controller were drum level and change in drum level. The dependent variable was the change required in the inlet flow. By modeling a 175,000 lb/hr Riley-Stoker boiler, they determined the universe of discourse for each of the three variables. Three triangular and two trapezoidal membership functions characterize each of these universes. The knowledge of experts provided the fuzzy associative memory (FAM) for the variables. The authors modeled the complete dynamic system using Tutsim (Tutsim Products, 200 California Ave., Palo Alto, CA 94306).

  13. Chimpanzee drumming: a spontaneous performance with characteristics of human musical drumming.

    PubMed

    Dufour, Valérie; Poulin, Nicolas; Charlotte Curé; Sterck, Elisabeth H M

    2015-06-17

    Despite the quintessential role that music plays in human societies by enabling us to release and share emotions with others, traces of its evolutionary origins in other species remain scarce. Drumming like humans whilst producing music is practically unheard of in our most closely related species, the great apes. Although beating on tree roots and body parts does occur in these species, it has, musically speaking, little in common with human drumming. Researchers suggest that for manual beating in great apes to be compared to human drumming, it should at least be structurally even, a necessary quality to elicit entrainment (beat induction in others). Here we report an episode of spontaneous drumming by a captive chimpanzee that approaches the structural and contextual characteristics usually found in musical drumming. This drumming differs from most beating episodes reported in this species by its unusual duration, the lack of any obvious context, and rhythmical properties that include long-lasting and dynamically changing rhythms, but also evenness and leisureliness. This performance is probably the first evidence that our capacity to drum is shared with our closest relatives.

  14. Chimpanzee drumming: a spontaneous performance with characteristics of human musical drumming

    PubMed Central

    Dufour, Valérie; Poulin, Nicolas; Charlotte Curé; Sterck, Elisabeth H. M.

    2015-01-01

    Despite the quintessential role that music plays in human societies by enabling us to release and share emotions with others, traces of its evolutionary origins in other species remain scarce. Drumming like humans whilst producing music is practically unheard of in our most closely related species, the great apes. Although beating on tree roots and body parts does occur in these species, it has, musically speaking, little in common with human drumming. Researchers suggest that for manual beating in great apes to be compared to human drumming, it should at least be structurally even, a necessary quality to elicit entrainment (beat induction in others). Here we report an episode of spontaneous drumming by a captive chimpanzee that approaches the structural and contextual characteristics usually found in musical drumming. This drumming differs from most beating episodes reported in this species by its unusual duration, the lack of any obvious context, and rhythmical properties that include long-lasting and dynamically changing rhythms, but also evenness and leisureliness. This performance is probably the first evidence that our capacity to drum is shared with our closest relatives. PMID:26080900

  15. 6. DETAIL OF THE BRAKE SHOE ON THE EAST DRUM ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    6. DETAIL OF THE BRAKE SHOE ON THE EAST DRUM AT THE STEWARD MINE, LOOKING EAST. THE EAST DRUM WAS UNDER SHOT, THE WEST OVERSHOT - Butte Mineyards, Stewart Mine, Intersection of Main & Woolman Streets, Butte, Silver Bow County, MT

  16. Nondestructive testing of waste drum integrity

    SciTech Connect

    Jackson, C.N. Jr.

    1983-01-01

    Nondestructive techniques have been investigated to evaluate the structural integrity of low-level transuranic waste drums that have been buried in the ground for up to 15 years. Measurements of artificially corroded samples evaluated suitability, accuracy and rapidity with which commercially available instruments and transducers could perform the examination. Several available instruments have thickness measuring capability and probably could be tailored with a relatively minor amount of effort for precise measurement of the relatively thin wall thickness of a drum or bin. The ultrasonic method was shown capable of providing precise measurement of wall thickness for most critical areas of a drum. Some data were lost due to dents, rust, seams and labels. However, this work characterized the capability of the technique, and it can now be assessed against the need as repository requirements are more completely identified.

  17. TRU Drum Headspace Gas Analysis System

    SciTech Connect

    Collins, S.

    1998-10-27

    The Savannah River Site (SRS) has approximately 10,000 Transuranic (TRU) waste drums whose final disposition is the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico. Each drum, prior to shipment to WIPP, must be inspected and tested to certify that is meets the WIPP requirements for acceptance. One, of many requirements, is the analysis of the TRU drum vapor space for hydrogen, methane, and volatile organic compounds (VOCs). The DOE Carlsbad Area Office has published two documents specifying the analytical methodologies and the quality assurance requirements for analyzing TRU drum vapor space.The Savannah River Technology Center (SRTC) was contracted by the Solid Waste Division of SRS to specify, assemble, and test a system that would satisfy the WIPP requirements for drum headspace gas analysis. Since no single vendor supplies a complete system, analytical instrumentation and supporting components were integrated into a configuration that performed that required analyses. This required both software and hardware design and modifications. The major goal of the design team was to integrate commercially available instrumentation and equipment into a seamless production process. The final output of the process is an analytical report formatted to the specifications outlined in the WIPP Quality Assurance Program Plan (QAPP). SRTC has assembled the necessary analytical instrumentation and installed it in a mobile trailer to perform the TRU drum vapor space analyses. This mobile trailer had previously housed instrumentation for reactor tank inspections. As a cost savings it was decided to renovate and install the instrumentation in this trailer to eliminate the need of building or modifying permanent structures. This also allows for portability to meet future analytical needs on or off site.This task was divided into three sub tasks: headspace gas sampling, gas analysis and system component integration, and sample canister cleaning. The following sections

  18. Final evaluation report for Westinghouse Hanford Company, WRAP-1,208 liter waste drum, docket 94-35-7A, type A packaging

    SciTech Connect

    Kelly, D.L., Westinghouse Hanford

    1996-06-12

    This report documents the U.S. Department of Transportation Specification 7A Type A (DOT-7A) compliance test results of the Westinghouse Hanford Company, Waste Receiving and Processing Facility, Module 1 (WRAP-1) Drum. The WRAP-1 Drum was tested for DOE-HQ in August 1994, by Los Alamos National Laboratory, under docket number 94-35-7A. Additionally, comparison and evaluation of the approved, as-tested packaging configuration was performed by WHC in September 1995. The WRAP-1 Drum was evaluated against the performance of the DOT-17C, 208 1 (55-gal) steel drums tested and evaluated under dockets 89-13-7A/90-18-7A and 94-37-7A.

  19. 30 CFR 75.1436 - Drum end attachment.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Hoisting and Mantrips Wire Ropes § 75.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one... full turns of wire rope shall be on the drum when the rope is extended to its maximum working length....

  20. 30 CFR 56.19026 - Drum end attachment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Personnel Hoisting Wire Ropes § 56.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1... engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope is extended...

  1. 30 CFR 57.19026 - Drum end attachment.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Wire Ropes § 57.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1... engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope is extended...

  2. 30 CFR 75.1436 - Drum end attachment.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Hoisting and Mantrips Wire Ropes § 75.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one... full turns of wire rope shall be on the drum when the rope is extended to its maximum working length....

  3. 30 CFR 57.19026 - Drum end attachment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Wire Ropes § 57.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1... engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope is extended...

  4. 30 CFR 56.19026 - Drum end attachment.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Personnel Hoisting Wire Ropes § 56.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1... engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope is extended...

  5. 30 CFR 57.19026 - Drum end attachment.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Wire Ropes § 57.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1... engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope is extended...

  6. 30 CFR 75.1436 - Drum end attachment.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Hoisting and Mantrips Wire Ropes § 75.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one... full turns of wire rope shall be on the drum when the rope is extended to its maximum working length....

  7. 30 CFR 75.1436 - Drum end attachment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Hoisting and Mantrips Wire Ropes § 75.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one... full turns of wire rope shall be on the drum when the rope is extended to its maximum working length....

  8. 30 CFR 56.19026 - Drum end attachment.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Personnel Hoisting Wire Ropes § 56.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1... engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope is extended...

  9. 30 CFR 75.1436 - Drum end attachment.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Hoisting and Mantrips Wire Ropes § 75.1436 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1) Securely by clips after making one... full turns of wire rope shall be on the drum when the rope is extended to its maximum working length....

  10. 30 CFR 56.19026 - Drum end attachment.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Personnel Hoisting Wire Ropes § 56.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1... engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope is extended...

  11. 30 CFR 56.19026 - Drum end attachment.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Personnel Hoisting Wire Ropes § 56.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1... engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope is extended...

  12. 30 CFR 57.19026 - Drum end attachment.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Wire Ropes § 57.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1... engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope is extended...

  13. 30 CFR 57.19026 - Drum end attachment.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Wire Ropes § 57.19026 Drum end attachment. (a) For drum end attachment, wire rope shall be attached— (1... engineer. (b) A minimum of three full turns of wire rope shall be on the drum when the rope is extended...

  14. 21 CFR 886.4230 - Ophthalmic knife test drum.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Ophthalmic knife test drum. 886.4230 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4230 Ophthalmic knife test drum. (a) Identification. An ophthalmic knife test drum is a device intended to test the keenness of ophthalmic...

  15. 21 CFR 886.4230 - Ophthalmic knife test drum.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Ophthalmic knife test drum. 886.4230 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4230 Ophthalmic knife test drum. (a) Identification. An ophthalmic knife test drum is a device intended to test the keenness of ophthalmic...

  16. 21 CFR 886.4230 - Ophthalmic knife test drum.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Ophthalmic knife test drum. 886.4230 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4230 Ophthalmic knife test drum. (a) Identification. An ophthalmic knife test drum is a device intended to test the keenness of ophthalmic...

  17. 21 CFR 886.4230 - Ophthalmic knife test drum.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ophthalmic knife test drum. 886.4230 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4230 Ophthalmic knife test drum. (a) Identification. An ophthalmic knife test drum is a device intended to test the keenness of ophthalmic...

  18. 21 CFR 886.4230 - Ophthalmic knife test drum.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Ophthalmic knife test drum. 886.4230 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4230 Ophthalmic knife test drum. (a) Identification. An ophthalmic knife test drum is a device intended to test the keenness of ophthalmic...

  19. Unsteady-state VOC transport in vented waste drums

    SciTech Connect

    Liekhus, K.J.; Gresham, G.L.; Peterson, E.S.; Rae, C.; Hotz, N.J.; Connolly, M.J.

    1993-08-01

    A model of unsteady-state volatile organic compound (VOC) transport in a vented waste drum has been developed. Model predictions of the VOC concentration in the innermost layer of confinement and the drum headspace are compared to measurements in lab-scale simulated waste drums.

  20. 49 CFR 178.505 - Standards for aluminum drums.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Standards for aluminum drums. 178.505 Section 178... PACKAGINGS Non-bulk Performance-Oriented Packaging Standards § 178.505 Standards for aluminum drums. (a) The following are the identification codes for aluminum drums: (1) 1B1 for a non-removable head aluminum...

  1. Microsatellite primers for red drum (Sciaenops ocellatus)

    Technology Transfer Automated Retrieval System (TEKTRAN)

    In this note, we document polymerase-chain-reaction (PCR) primer pairs for 101, nuclear-encoded microsatellites designed and developed from a red drum (Sciaenops ocellatus) genomic library. The 101 microsatellites (Genbank Accession Numbers EU015882-EU015982) were amplified successfully and used to...

  2. Potential VOC Deflagrations in a Vented TRU Drum

    SciTech Connect

    Mukesh, GUPTA

    2005-04-07

    The objective of the analysis is to examine the potential for lid ejection from a vented transuranic (TRU) waste drum due to pressure buildup caused by the deflagration of hydrogen and volatile organic compounds (VOCs) inside the drum. In this analysis, the AICC pressure for a stoichiometric mixture of VOCs is calculated and then compared against the experimental peak pressure of stoichiometric combustion of propane and hexane in a combustion chamber. The experimental peak pressures of propane and hexane are about 12 percent lower than the calculated AICC pressure. Additional losses in the drum are calculated due to venting of the gases, drum bulging, waste compaction, and heat losses from the presence of waste in the drum. After accounting for these losses, the final pressures are compared to the minimum observed pressure that ejects the lid from a TRU drum. The ejection pressure of 105 psig is derived from data that was recorded for a series of tests where hydrogen-air mixtures were ignited inside sealed TRU drums. Since the calculated pressures are below the minimum lid ejection pressure, none of the VOCs and the hydrogen (up to 4 percent) mixtures present in the TRU waste drum is expected to cause lid ejection if ignited. The analysis of potential VOC deflagrations in a vented TRU drum can be applied across the DOE-Complex since TRU waste is stored in drums throughout the complex.

  3. Simulating Lahars Using A Rotating Drum

    NASA Astrophysics Data System (ADS)

    Neather, Adam; Lube, Gert; Jones, Jim; Cronin, Shane

    2014-05-01

    A large (0.5 m in diameter, 0.15 m wide) rotating drum is used to investigate the erosion and deposition mechanics of lahars. To systematically simulate the conditions occurring in natural mass flows our experimental setup differs from the common rotating drum employed in industrial/engineering studies. Natural materials with their typical friction properties are used, as opposed to the frequently employed spherical glass beads; the drum is completely water-proof, so solid/air and solid/liquid mixtures can be investigated; the drum velocity and acceleration can be precisely controlled using a software interface to a micro-controller, allowing for the study of steady, unsteady and intermediate flow regimes. The drum has a toughened glass door, allowing high-resolution, high-speed video recording of the material inside. Vector maps of the velocities involved in the flows are obtained using particle image velocimetry (PIV). The changes in velocity direction and/or magnitude are used to locate the primary internal boundaries between layers of opposite flow direction, as well as secondary interfaces between shear layers. A range of variables can be measured: thickness and number of layers; the curvature of the free surface; frequency of avalanching; position of the centre of mass of the material; and the velocity profiles of the flowing material. Experiments to date have focussed on dry materials, and have had a fill factor of approximately 0.3. Combining these measured variables allows us to derive additional data of interest, such as mass and momentum flux. It is these fluxes that we propose will allow insight into the erosion/deposition mechanics of a lahar. A number of conclusions can be drawn to date. A primary interface separates flowing and passive region (this interface has been identified in previous studies). As well as the primary interface, the flowing layer separates into individual shear layers, with individual erosion/deposition and flow histories. This

  4. Size limitation on zebra mussels consumed by freshwater drum may preclude the effectiveness of drum as a biological controller

    USGS Publications Warehouse

    French, John R. P.; Love, Joy G.

    1995-01-01

    The septa lengths of bivalve shells were used to estimate shell lengths of the largest zebra mussels (Dreissena polymorpha) crushed and consumed by freshwater drum (Aplodinotus grunniens) to determine if size limitation could preclude the effectiveness of drum as a biological controller of the zebra mussel. We examined gut samples of drum (273 to 542 mm long) collected from western Lake Erie in 1991, found the largest mussel (shell length = 21.4 mm) in the 11th largest drum (TL = 405 mm), and observed a reduction of mussel size in larger drum. The lack of a relationship between mussel size and drum size for larger specimens suggests that either drum prefer smaller mussels or the gape between the upper and lower pharyngeal teeth restricts drum feeding to zebra mussels of limited size. Although drum may reduce zebra mussel populations, because of the apparent size limitation of prey it is unlikely that drum would be fully effective as a biological controller; thus, this fish should not be introduced beyond its native range for that purpose.

  5. Active Drumming Experience Increases Infants’ Sensitivity to Audiovisual Synchrony during Observed Drumming Actions

    PubMed Central

    Timmers, Renee; Hunnius, Sabine

    2015-01-01

    In the current study, we examined the role of active experience on sensitivity to multisensory synchrony in six-month-old infants in a musical context. In the first of two experiments, we trained infants to produce a novel multimodal effect (i.e., a drum beat) and assessed the effects of this training, relative to no training, on their later perception of the synchrony between audio and visual presentation of the drumming action. In a second experiment, we then contrasted this active experience with the observation of drumming in order to test whether observation of the audiovisual effect was as effective for sensitivity to multimodal synchrony as active experience. Our results indicated that active experience provided a unique benefit above and beyond observational experience, providing insights on the embodied roots of (early) music perception and cognition. PMID:26111226

  6. Active Drumming Experience Increases Infants' Sensitivity to Audiovisual Synchrony during Observed Drumming Actions.

    PubMed

    Gerson, Sarah A; Schiavio, Andrea; Timmers, Renee; Hunnius, Sabine

    2015-01-01

    In the current study, we examined the role of active experience on sensitivity to multisensory synchrony in six-month-old infants in a musical context. In the first of two experiments, we trained infants to produce a novel multimodal effect (i.e., a drum beat) and assessed the effects of this training, relative to no training, on their later perception of the synchrony between audio and visual presentation of the drumming action. In a second experiment, we then contrasted this active experience with the observation of drumming in order to test whether observation of the audiovisual effect was as effective for sensitivity to multimodal synchrony as active experience. Our results indicated that active experience provided a unique benefit above and beyond observational experience, providing insights on the embodied roots of (early) music perception and cognition.

  7. VOC transport in vented drums containing simulated waste sludge

    SciTech Connect

    Liekhus, K.J.; Gresham, G.L.; Rae, C.; Connolly, M.J.

    1994-02-01

    A model is developed to estimate the volatile organic compound (VOC) concentration in the headspace of the innermost layer of confinement in a lab-scale vented waste drum containing simulated waste sludge. The VOC transport model estimates the concentration using the measured VOC concentration beneath the drum lid and model parameters defined or estimated from process knowledge of drum contents and waste drum configuration. Model parameters include the VOC diffusion characteristic across the filter vent, VOC diffusivity in air, size of opening in the drum liner lid, the type and number of layers of polymer bags surrounding the waste, VOC permeability across the polymer, and the permeable surface area of the polymer bags. Comparison of model and experimental results indicates that the model can accurately estimate VOC concentration in the headspace of the innermost layer of confinement. The model may be useful in estimating the VOC concentration in actual waste drums.

  8. Remote radioactive waste drum inspection with an autonomous mobile robot

    SciTech Connect

    Heckendorn, F.M.; Ward, C.R.; Wagner, D.G.

    1992-01-01

    An autonomous mobile robot is being developed to perform remote surveillance and inspection task on large numbers of stored radioactive waste drums. The robot will be self guided through narrow storage aisles and record the visual image of each viewable drum for subsequent off line analysis and archiving. The system will remove the personnel from potential exposure to radiation, perform the require inspections, and improve the ability to assess the long term trends in drum conditions.

  9. Remote radioactive waste drum inspection with an autonomous mobile robot

    SciTech Connect

    Heckendorn, F.M.; Ward, C.R.; Wagner, D.G.

    1992-11-01

    An autonomous mobile robot is being developed to perform remote surveillance and inspection task on large numbers of stored radioactive waste drums. The robot will be self guided through narrow storage aisles and record the visual image of each viewable drum for subsequent off line analysis and archiving. The system will remove the personnel from potential exposure to radiation, perform the require inspections, and improve the ability to assess the long term trends in drum conditions.

  10. Simultaneous Thermal Analysis of WIPP and LANL Waste Drum Samples: A Preliminary Report

    SciTech Connect

    Wayne, David M.

    2015-10-19

    On Friday, February 14, 2014, an incident in P7R7 of the WIPP underground repository released radioactive material into the environment. The direct cause of the event was a breached transuranic (TRU) waste container, subsequently identified as Drum 68660. Photographic and other evidence indicates that the breach of 68660 was caused by an exothermic event. Subsequent investigations (Britt, 2015; Clark and Funk, 2015; Wilson et al., 2015; Clark, 2015) indicate that the combination of nitrate salts, pH neutralizing chemicals, and organic-based adsorbent represented a potentially energetic mixture. The materials inside the breached steel drum consisted of remediated, 30- to 40-year old, Pu processing wastes from LANL. The contents were processed and repackaged in 2014. Processing activities at LANL included: 1) neutralization of acidic liquid contents, 2) sorption of the neutralized liquid, and 3) mixing of acidic nitrate salts with an absorber to meet waste acceptance criteria. The contents of 68660 and its sibling, 68685, were derived from the same parent drum, S855793. Drum S855793 originally contained ten plastic bags of acidic nitrate salts, and four bags of mixed nitrate and oxalate salts generated in 1985 by Pu recovery operations. These salts were predominantly oxalic acid, hydrated nitrate salts of Mg, Ca, and Fe, anhydrous Na(NO3), and minor amounts of anhydrous and hydrous nitrate salts of Pb, Al, K, Cr, and Ni. Other major components include sorbed water, nitric acid, dissolved nitrates, an absorbent (Swheat Scoop®) and a neutralizer (KolorSafe®). The contents of 68660 are described in greater detail in Appendix E of Wilson et al. (2015)

  11. Frequent Questions About EPA's Mercury Lamp Drum-Top Crusher Study

    EPA Pesticide Factsheets

    Frequent Questions such as Why did we do the Mercury Lamp Drum-Top Crusher Study?, Should drum-top crushers (DTCs) be used in the management of fluorescent lamps?, Are drum-top crushers (DTCs) safe to use?

  12. Reference drums used in calibration of a plastic scintillation counter in a 4π counting geometry.

    PubMed

    Yeh, Chin-Hsien; Yuan, Ming-Chen

    2016-03-01

    In this study, two kinds of reference drums were developed. One type was constructed with nine layers of large-area sources filled with different materials having five different densities. The other type of reference drums was constructed with nine rod sources filled with the same materials of different densities. The efficiency calibration of a plastic scintillation counter in 4π counting geometry using these two kinds of drums showed that rod-source drums resulted in higher counting efficiency than layered source drums. The counting rates obtained from rod-source drums were closer to those obtained from a standard drum with water solution than counting rates from drums with layered sources. The results of this study recommend to use reference drums with rod-sources to compensate the drawbacks of standard drums with water solution of not being able to adjust the density of material. The proposed reference drums improve the accuracy of radioactivity analysis for waste drums of different densities.

  13. Cookoff Modeling of a WIPP waste drum (68660)

    SciTech Connect

    Hobbs, Michael L.

    2014-11-24

    A waste drum located 2150 feet underground may have been the root cause of a radiation leak on February 14, 2014. Information provided to the WIPP Technical Assessment Team (TAT) was used to describe the approximate content of the drum, which included an organic cat litter (Swheat Scoop®, or Swheat) composed of 100% wheat products. The drum also contained various nitrate salts, oxalic acid, and a nitric acid solution that was neutralized with triethanolamine (TEA). CTH-TIGER was used with the approximate drum contents to specify the products for an exothermic reaction for the drum. If an inorganic adsorbent such as zeolite had been used in lieu of the kitty litter, the overall reaction would have been endothermic. Dilution with a zeolite adsorbent might be a useful method to remediate drums containing organic kitty litter. SIERRA THERMAL was used to calculate the pressurization and ignition of the drum. A baseline simulation of drum 68660 was performed by assuming a background heat source of 0.5-10 W of unknown origin. The 0.5 W source could be representative of heat generated by radioactive decay. The drum ignited after about 70 days. Gas generation at ignition was predicted to be 300-500 psig with a sealed drum (no vent). At ignition, the wall temperature increases modestly by about 1°C, demonstrating that heating would not be apparent prior to ignition. The ignition location was predicted to be about 0.43 meters above the bottom center portion of the drum. At ignition only 3-5 kg (out of 71.6 kg total) has been converted into gas, indicating that most of the material remained available for post-ignition reaction.

  14. 29 CFR 1915.173 - Drums and containers.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... vessels, drums and containers containing toxic or flammable liquids or gases shall not be stored or used where they are subject to open flame, hot metal, or other sources of artificial heat. (d) Unless pressure vessels, drums and containers of 30 gallon capacity or over containing flammable or toxic...

  15. Mobile drum crusher prevents pollution, cuts disposal costs

    SciTech Connect

    Vasseur, J.C. )

    1994-12-01

    Sfanid Renov' Cuves, of Goussainville, France, has developed an alternative to stockpiling potentially dangerous used drums. Quick Futs (''quick barrels'') is a mobile unit that neutralizes metal drums and packaging materials. The onsite treatment system saves customers money on drum processing and transportation costs. The per-ton cost of delivering drums containing chemical residues to a disposal center is substantially higher than the cost of delivering only the residues in bulk or tank trucks, and takes more time. The Quick Futs system cleans drums under high pressure, crushes them, and pumps out and recovers residual chemicals and rinse water before shipping the drums to an approved center for final destruction. As a stationary unit, the Quick Futs system can be used to process empty drums daily, avoiding the need to store used drums in an area that could be used for a more productive purpose. Quick Futs is designed to meet safety requirements for explosion-proof equipment in refineries. As a mobile unit, Quick Futs offers the advantages of the stationary unit and provides added peace of mind for those who see the unit on a customer's premises. The process is especially valuable for companies whose packaging materials cannot be reused.

  16. Impact of drum storage on criticality accident alarm systems

    SciTech Connect

    Finfrock, S.; Watson, T.; Byrd, J.; Miles, B.; Wilkinson, A.

    1997-12-01

    The changing mission from production to decommissioning that is taking place at many U.S. Department of Energy sites is producing an ever-increasing inventory of waste drums. These drums typically contain low-level radioactive waste and, in some cases, significant amounts of fissile materials. Such drums must be handled with all of the care necessary for radioactive materials and, where fissile materials are present, criticality safety controls. As the number of drums increases, the question inevitably arises as to where to store them. Old process buildings present one solution to that question. These buildings are typically large, designed to handle radioactive and fissile materials, and largely unused under the current mission and, as such, would seem ideal candidates for at least short-term storage of waste drums. When undergoing such a major change in mission, however, the building`s nuclear safety systems need to be reevaluated to ensure that they are appropriate for the new activity. One such system that must be evaluated is the building`s criticality accident alarm system (AAS). This system is designed to detect criticality accidents and is generally required anywhere that a criticality accident is credible. If drums are to be stored in a facility where a CAAS is required (either because of other activities in the building or because of the contents of the drums themselves), then those drums must be shown not to prevent the CAAS from functioning as designed.

  17. 49 CFR 178.508 - Standards for fiber drums.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Standards for fiber drums. 178.508 Section 178.508 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY...-Oriented Packaging Standards § 178.508 Standards for fiber drums. (a) The identification code for a...

  18. 49 CFR 178.508 - Standards for fiber drums.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Standards for fiber drums. 178.508 Section 178.508 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY...-Oriented Packaging Standards § 178.508 Standards for fiber drums. (a) The identification code for a...

  19. Drum ring removal/installation tool

    DOEpatents

    Andrade, William Andrew

    2006-11-14

    A handheld tool, or a pair of such tools, such as for use in removing/installing a bolt-type clamping ring on a container barrel/drum, where the clamping ring has a pair of clamping ends each with a throughbore. Each tool has an elongated handle and an elongated lever arm transversely connected to one end of the handle. The lever arm is capable of being inserted into the throughbore of a selected clamping end and leveraged with the handle to exert a first moment on the selected clamping end. Each tool also has a second lever arm, such as a socket with an open-ended slot, which is suspended alongside the first lever arm. The second lever arm is capable of engaging the selected clamping end and being leveraged with the handle to exert a second moment which is orthogonal to the first moment. In this manner, the first and second moments operate to hold the selected clamping end fixed relative to the tool so that the selected clamping end may be controlled with the handle. The pair of clamping ends may also be simultaneously and independently controlled with the use of two handles/tools so as to contort the geometry of the drum clamping ring and enable its removal/installation.

  20. Drum dispersion equation for Littrow-type prism spectrometers.

    PubMed

    Sidran, M; Stalzer, H J; Hauptman, M H

    1966-07-01

    A simple analytic procedure has been developed for calibrating the wavelength drum of a Littrow-type prism spectrometer. Only three measured drum readings are required to specify the drum calibration over a broad wavelength range (uv to ir) with an accuracy of the order of the instrumental accuracy. This procedure can be applied to different prism materials for which measurements of refractive index have been performed. It is based on an approximate expression, derived from geometrical optics, relating the drum reading D(lambda) to the calculated refractive index n(lambda): D= A - B(a(2) - n(2))((1/2)). The index n(lambda) is calculated from the appropriate parametric equation. The temperature for the n(lambda) values need not be exactly that of the prism temperature during measurements. This expression was investigated for wavelengths in the range 0.3 micro to 2.25 micro using a sodium chloride prism. Computed drum positions D agreed with measured drum positions to within experimental error. Unknown wavelengths were computed from their measured drum positions to within the accuracy of the measurements.

  1. 49 CFR 178.508 - Standards for fiber drums.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... laminated together and may include one or more protective layers of bitumen, waxed kraft paper, metal foil... paper, metal foil, plastic material, or similar material. (3) The body and heads of the drum and...

  2. View of furnace feeding into the drum type coffee dryer ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of furnace feeding into the drum type coffee dryer on second floor of structure, view towards southeast - Santaella Coffee Processing Site, Highway 139, Kilometer 10.6, Maraguez, Ponce Municipio, PR

  3. The Play as Novel: Reappropriating Brecht's "Drums in the Night."

    ERIC Educational Resources Information Center

    Pollock, Della

    1988-01-01

    Applies Mikhail Bakhtin's theory of the novel to Bertolt Brecht's "Drums in the Night" to illuminate the play's dialogic structure and alienation value, and reappropriate its prerevolutionary dimensions for contemporary use. (MM)

  4. Slit Logs and Sacred Cows: The History of the Drum.

    ERIC Educational Resources Information Center

    Music Educators Journal, 1979

    1979-01-01

    The evolution of the drum is presented in both pictures and prose, from its beginning in Africa and the Far Eastern world to its introduction to the Western world where it is now fully accepted as a serious instrument. (KC)

  5. 49 CFR 178.507 - Standards for plywood drums.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ....507 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS SPECIFICATIONS FOR... effectiveness of the drum for the purpose intended. A material other than plywood, of at least...

  6. 4. DETAIL OF ELEVATOR DRUM AND DRIVE. Hot Springs ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. DETAIL OF ELEVATOR DRUM AND DRIVE. - Hot Springs National Park, Bathhouse Row, Fordyce Bathhouse: Mechanical & Piping Systems, State Highway 7, 1 mile north of U.S. Highway 70, Hot Springs, Garland County, AR

  7. 49 CFR 178.507 - Standards for plywood drums.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR PACKAGINGS Non..., with their grains crosswise. (3) The body and heads of the drum and their joints must be of a...

  8. View of main hoist wire rope drum and brakes, open ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of main hoist wire rope drum and brakes, open contact boards are in view at the far right wall - Puget Sound Naval Shipyard, Portal Gantry Crane No. 42, Pier 5, Farragut Avenue, Bremerton, Kitsap County, WA

  9. 49 CFR 178.507 - Standards for plywood drums.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ..., lids must be lined with kraft paper or some other equivalent material which must be securely fastened to the lid and extend to the outside along its full circumference. (5) Maximum capacity of drum:...

  10. 49 CFR 178.507 - Standards for plywood drums.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ..., lids must be lined with kraft paper or some other equivalent material which must be securely fastened to the lid and extend to the outside along its full circumference. (5) Maximum capacity of drum:...

  11. 49 CFR 178.507 - Standards for plywood drums.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ..., lids must be lined with kraft paper or some other equivalent material which must be securely fastened to the lid and extend to the outside along its full circumference. (5) Maximum capacity of drum:...

  12. 1. OBLIQUE VIEW OF HOIST, SHOWING CABLE DRUM, WOODEN BRAKE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. OBLIQUE VIEW OF HOIST, SHOWING CABLE DRUM, WOODEN BRAKE SHOES AND BRAKE HANDLE, LOOKING NORTH - Buffalo Coal Mine, Vulcan Cable Hoist, Wishbone Hill, Southeast end, near Moose Creek, Sutton, Matanuska-Susitna Borough, AK

  13. 2. OBLIQUE VIEW OF HOIST, SHOWING CABLE DRUM, WOODEN BRAKE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    2. OBLIQUE VIEW OF HOIST, SHOWING CABLE DRUM, WOODEN BRAKE SHOES, BRAKE HANDLE, AND REDUCTION GEARS, LOOKING SOUTHWEST - Buffalo Coal Mine, Vulcan Cable Hoist, Wishbone Hill, Southeast end, near Moose Creek, Sutton, Matanuska-Susitna Borough, AK

  14. American Recovery and Reinvestment Act Projects - Fort Drum, New York

    DTIC Science & Technology

    2010-06-21

    Army Corps of Engineers Figure 2. Solar Walls Installed on a Maintenance Shop at Fort Drum Source: IEA Energy Conservation in Buildings and...a $1.6 million Energy Conservation Investment Program project to rehabilitate and install solar walls in Fort Drum maintenance shops. What We...contracted for, and began execution of Recovery Act projects for constructing a child development center and rehabilitating and installing solar

  15. The correlation between acoustic and magnetic properties in the long working metal boiler drum with the parameters of the electron microscope

    NASA Astrophysics Data System (ADS)

    Ababkov, Nikolai; Smirnov, Alexander

    2016-01-01

    The present paper presents comparative analysis of measurement results of acoustic and magnetic properties in long working metal of boiler drums and the results obtained by methods of electronic microscopy. The structure of the metal sample from the fracture zone to the base metal (metal working sample long) and the center of the base metal before welding (weld metal sample) was investigated by electron microscopy. Studies performed by spectral acoustic, magnetic noise and electron microscopic methods were conducted on the same plots and the same samples of long working and weld metal of high-pressure boiler drums. The analysis of research results showed high sensitivity of spectral-acoustic and magnetic-noise methods to definition changes of microstructure parameters. Practical application of spectral-acoustic and magnetic noise NDT method is possible for the detection of irregularities and changes in structural and phase state of the long working and weld metal of boiler drums, made of a special molybdenum steel (such as 20M). The above technique can be used to evaluate the structure and physical-mechanical properties of the long working metal of boiler drums in the energy sector.

  16. The correlation between acoustic and magnetic properties in the long working metal boiler drum with the parameters of the electron microscope

    SciTech Connect

    Ababkov, Nikolai Smirnov, Alexander

    2016-01-15

    The present paper presents comparative analysis of measurement results of acoustic and magnetic properties in long working metal of boiler drums and the results obtained by methods of electronic microscopy. The structure of the metal sample from the fracture zone to the base metal (metal working sample long) and the center of the base metal before welding (weld metal sample) was investigated by electron microscopy. Studies performed by spectral acoustic, magnetic noise and electron microscopic methods were conducted on the same plots and the same samples of long working and weld metal of high-pressure boiler drums. The analysis of research results showed high sensitivity of spectral-acoustic and magnetic-noise methods to definition changes of microstructure parameters. Practical application of spectral-acoustic and magnetic noise NDT method is possible for the detection of irregularities and changes in structural and phase state of the long working and weld metal of boiler drums, made of a special molybdenum steel (such as 20M). The above technique can be used to evaluate the structure and physical-mechanical properties of the long working metal of boiler drums in the energy sector.

  17. Nuclear criticality safety for drums at Babcock and Wilcox

    SciTech Connect

    Alcorn, F.M.

    1997-12-01

    The Babcock and Wilcox Company (B&W) operates a nuclear fuel facility in Lynchburg, Virginia, processing uranium over the full range of possible enrichments (depleted to 97.65 wt% {sup 235}U). Nuclear fuel is produced for defense programs and for various research and test reactors worldwide. The facility has a uranium recovery operation that handles scrap produced at B&W as well as scrap from other U.S. Department of Energy sites. B&W also has a down-blending operation that is currently completing the down-blending of the fully enriched Project Sapphire Uranium to commercial-grade fuel (4 Wt% {sup 235}U). The facility generates approximately two hundred 55-gal drums of radioactive waste each month. Just a few years ago the number of waste drums on-site stood at {approximately}5000; however, through an aggressive waste reduction program, this number has been reduced to {approximately}2000. B&W strives to avoid storing uranium scrap in 55-gal drums; however, there are approximately sixty-four 55-gal drums of scrap on-site. Scrap is that material from which the uranium is recovered because of financial, contractual, or regulatory considerations; waste is that material destined for disposal. Whether waste or scrap, nuclear criticality safety is of paramount concern in the handling, processing, and storing of uranium-bearing drums at B&W. Any shipment complies with applicable U.S. Nuclear Regulatory Commission and U.S. Department of Transportation regulations.

  18. 3M heavy duty roto peen: Baseline report; Summary

    SciTech Connect

    1997-07-31

    The roto peen scaler allows for the selective removal of concrete substrates. The peen is a tungsten carbide shot brazed to a hardened steel rivet that is supported by a heavy duty flexible flap. The peens are coupled with a commercially available piece of equipment that is used to scabble or remove the concrete. The scabbled debris is then collected into 55 gallon drums by means of a vacuum system. The safety and health evaluation during the human factors assessment focused on two main areas: noise and dust.

  19. 77 FR 24200 - American Drum & Pallet, Memphis, Shelby County, TN; Notice of Settlement

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-23

    ...-04- 2012-3770 or Site name American Drum & Pallet Superfund Site by one of the following methods: www... settlement for reimbursement of past response costs concerning the American Drum and Pallet Superfund...

  20. Red drum Sciaenops ocellatus mortalities associated with Streptococcus iniae infection.

    PubMed

    Eldar, A; Perl, S; Frelier, P F; Bercovier, H

    1999-05-12

    We isolated for the first time Streptococcus iniae strains associated with diseased marine fish. Diseased red drum Sciaenops ocellatus were lethargic, and presented external signs (exophthalmia and loss of orientation) resembling those of freshwater fish infected by S. iniae. Skin lesions, extending to a necrotizing myositis, were typical of S. iniae infection of red drum. Histopathological findings indicate that S. iniae infection in red drum produces a chronic disease with systemic involvement characterized by multiple necrotic foci. Molecular epidemiology (RFLP [restriction fragment length polymorphism] ribotyping) revealed that 2 different ribotypes were involved in a single outbreak. The first is the EcoRI 'Israeli' trout and tilapine ribotype (Hind III type a strains), while the second is the EcoRI 'American' ribotype (Hind III type b strains), typical of tilapines farmed in Texas and Idaho.

  1. Tread drum for animals. [having an electrical shock station

    NASA Technical Reports Server (NTRS)

    Howard, W. H. (Inventor)

    1978-01-01

    A device for exercising animals such as primates is described, which includes a cylindrical housing mounted for rotation about a horizontal axis of revolution and has a cylindrical treadway portion on which the animal treads while the drum is rotated by means of a motorized drive. The treadway portion of the drum includes an electrode structure with sectors being independently energizable by means of a commutator and source of potential so that an electrical shock station is created behind a running-in-place station on the moving treadway. In this manner, if the animal should fall behind its running-in-place station, it may be shocked by treading on the energized electrode structure. One end of the tread drum comprises a transparent wall for unobstructed viewing of the animal being exercised.

  2. Dietary choline requirement of juvenile red drum (Sciaenops ocellatus).

    PubMed

    Craig, S R; Gatlin, D M

    1996-06-01

    A 6-wk feeding experiment was conducted to determine the maximal dietary choline requirement of juvenile red drum (Sciaenops ocellatus). Diets were formulated to provide 35 g crude protein/ 100 g dry weight from solvent-extracted lyophilized red drum muscle and an amino acid premix. This premix provided methionine precisely at the minimum requirement determined for red drum so that potential synthesis of choline from methionine would be limited. Menhaden oil and dextrin were added to all diets to provide 13.8 kJ metabolizable energy/g diet as estimated by physiological fuel values. The diets were supplemented with choline chloride to provide 0, 250, 500, 750, 1000 and 1500 mg choline/kg diet. Each diet was fed to triplicate groups of red drum initially averaging 5.5 g/fish in a closed, recirculating system consisting of 110-L glass aquaria. Dietary choline concentration significantly (P < 0.05) affected weight gain, feed efficiency, total lipid in liver and plasma, as well as plasma cholesterol ester, triglyceride, cholesterol and phosphatidylcholine concentrations. Least-squares regression of these responses yielded requirements ranging from 330 to 676 mg choline/kg diet. Based on weight gain data, a maximal requirement estimate (+/- SEM) of 588 (+/- 35) mg choline/kg diet was established. Red drum appear to differ from other animals in regard to the response of total lipid in liver because fish fed choline-deficient diets had reduced liver lipid rather than lipid accumulation. Cultured red drum normally store high levels of lipid in the liver.

  3. Cascade generalized predictive control strategy for boiler drum level.

    PubMed

    Xu, Min; Li, Shaoyuan; Cai, Wenjian

    2005-07-01

    This paper proposes a cascade model predictive control scheme for boiler drum level control. By employing generalized predictive control structures for both inner and outer loops, measured and unmeasured disturbances can be effectively rejected, and drum level at constant load is maintained. In addition, nonminimum phase characteristic and system constraints in both loops can be handled effectively by generalized predictive control algorithms. Simulation results are provided to show that cascade generalized predictive control results in better performance than that of well tuned cascade proportional integral differential controllers. The algorithm has also been implemented to control a 75-MW boiler plant, and the results show an improvement over conventional control schemes.

  4. Renewable Energy Opportunities at Fort Drum, New York

    SciTech Connect

    Brown, Scott A.; Orrell, Alice C.; Solana, Amy E.; Williamson, Jennifer L.; Hand, James R.; Russo, Bryan J.; Weimar, Mark R.; Rowley, Steven; Nesse, Ronald J.

    2010-10-20

    This document provides an overview of renewable resource potential at Fort Drum, based primarily upon analysis of secondary data sources supplemented with limited on-site evaluations. This effort focuses on grid-connected generation of electricity from renewable energy sources and also on ground source heat pumps for heating and cooling buildings. The effort was funded by the U.S. Army Installation Management Command (IMCOM) as follow-on to the 2005 Department of Defense (DoD) Renewables Assessment. The site visit to Fort Drum took place on May 4 and 5, 2010.

  5. Payload Specific Evaluation for Concrete Lined Drums in the Standard Waste Box

    SciTech Connect

    JOHNSON, P.G.

    2002-07-11

    Building 327 uses concrete-lined drums for handling waste generated from deactivation activities. This payload-specific evaluation assesses the shipment of these concrete-lined drums, as well as future drums, in the Standard Waste Box, certified Type A.

  6. 49 CFR 178.509 - Standards for plastic drums and jerricans.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Standards for plastic drums and jerricans. 178.509... PACKAGINGS Non-bulk Performance-Oriented Packaging Standards § 178.509 Standards for plastic drums and jerricans. (a) The following are identification codes for plastic drums and jerricans: (1) 1H1 for a...

  7. 49 CFR 178.509 - Standards for plastic drums and jerricans.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Standards for plastic drums and jerricans. 178.509... PACKAGINGS Non-bulk Performance-Oriented Packaging Standards § 178.509 Standards for plastic drums and jerricans. (a) The following are identification codes for plastic drums and jerricans: (1) 1H1 for a...

  8. 49 CFR 178.509 - Standards for plastic drums and jerricans.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Standards for plastic drums and jerricans. 178.509... PACKAGINGS Non-bulk Performance-Oriented Packaging Standards § 178.509 Standards for plastic drums and jerricans. (a) The following are identification codes for plastic drums and jerricans: (1) 1H1 for a...

  9. 49 CFR 178.509 - Standards for plastic drums and jerricans.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Standards for plastic drums and jerricans. 178.509... PACKAGINGS Non-bulk Performance-Oriented Packaging Standards § 178.509 Standards for plastic drums and jerricans. (a) The following are identification codes for plastic drums and jerricans: (1) 1H1 for a...

  10. 49 CFR 178.509 - Standards for plastic drums and jerricans.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Standards for plastic drums and jerricans. 178.509... FOR PACKAGINGS Non-bulk Performance-Oriented Packaging Standards § 178.509 Standards for plastic drums and jerricans. (a) The following are identification codes for plastic drums and jerricans: (1) 1H1...

  11. The Oral Tradition in the Sankofa Drum and Dance Ensemble: Student Perceptions

    ERIC Educational Resources Information Center

    Hess, Juliet

    2009-01-01

    The Sankofa Drum and Dance Ensemble is a Ghanaian drum and dance ensemble that focusses on music in the Ewe tradition. It is based in an elementary school in the Greater Toronto Area and consists of students in Grade 4 through Grade 8. Students in the ensemble study Ghanaian traditional Ewe drumming and dancing in the oral tradition. Nine students…

  12. Analytical and experimental evaluation of solid waste drum fire performance volumes I and II

    SciTech Connect

    Hecker, C.F.,; Rhodes, B.T.; Beitel, J.J.; Gottuk, D.T.; Beyler, C.L.; Rosenbaum, E.R.,

    1995-04-28

    Fire hazards associated with drum storage of radioactively contaminated wastes are a major concern in DOE facilities design for long term storage of solid wastes in drums. These facilities include drums stored in pallet arrays and in rack storage systems. This report details testing in this area

  13. Nondestructive assay of curium-contaminated transuranic waste drums

    NASA Astrophysics Data System (ADS)

    Foster, Lynn A.

    1999-01-01

    At the Plutonium Facility at Los Alamos National Laboratory, a series of non-destructive assays were performed on five transuranic waste drums containing non-actinide scrap metal that was potentially contaminated with weapons grade plutonium and trace quantities of curium. Typically, waste drums containing metal matrices are assayed for plutonium content using passive neutron coincidence counting techniques. The presence of trace quantities of 244Cm prevents this type of analysis because of the strong coincidence signal created by spontaneous fission of 244Cm. To discrimination between the plutonium and curium materials in the matrix, an active neutron measurement technique was used. A californium shuffler designed for measurement of uranium bearing materials was calibrated for plutonium in the active mode. The waste drums were then assayed for plutonium content in the shuffler using the active-mode calibration, which is relatively insensitive to the 244Cm contamination. The curium contamination levels were estimated from the difference between the active-mode measurement in the shuffler and a passive assay in a neutron coincidence counter. Far field gamma-ray measurements were made to identify additional radioactive contaminants and to corroborate the plutonium measurement results obtained from the active-mode assay. This report describes in detail the measurement process used for characterization of these waste drums. The measurement results and the estimated uncertainty will be presented.

  14. The Way of the Drum: When Earth Becomes Heart.

    ERIC Educational Resources Information Center

    Antone, Grafton; Turchetti, Lois Provost

    Two Native people describe their respective journeys to healing, journeys that involved the rediscovery of language and culture. In Part I, "Healing the Tears of Yesterday by the Drum Today: The Oneida Language Is a Healing Medicine" (Grafton Antone), the first narrator taught the Oneida language to adult students at a community center.…

  15. Small-Scale Experiments.10-gallon drum experiment summary

    SciTech Connect

    Rosenberg, David M.

    2015-02-05

    A series of sub-scale (10-gallon) drum experiments were conducted to characterize the reactivity, heat generation, and gas generation of mixtures of chemicals believed to be present in the drum (68660) known to have breached in association with the radiation release event at the Waste Isolation Pilot Plant (WIPP) on February 14, 2014, at a scale expected to be large enough to replicate the environment in that drum but small enough to be practical, safe, and cost effective. These tests were not intended to replicate all the properties of drum 68660 or the event that led to its breach, or to validate a particular hypothesis of the release event. They were intended to observe, in a controlled environment and with suitable diagnostics, the behavior of simple mixtures of chemicals in order to determine if they could support reactivity that could result in ignition or if some other ingredient or event would be necessary. There is a significant amount of uncertainty into the exact composition of the barrel; a limited sub-set of known components was identified, reviewed with Technical Assessment Team (TAT) members, and used in these tests. This set of experiments was intended to provide a framework to postulate realistic, data-supported hypotheses for processes that occur in a “68660-like” configuration, not definitively prove what actually occurred in 68660.

  16. Dynamics of Axial Separation in Long Rotating Drums

    SciTech Connect

    Aranson, I.S.; Tsimring, L.S.

    1999-06-01

    We propose a continuum description for the axial separation of granular materials in a long rotating drum. The model, operating with two local variables, concentration difference and the dynamic angle of repose, describes both initial transient traveling wave dynamics and long-term segregation of the binary mixture. Segregation proceeds through ultraslow logarithmic coarsening. {copyright} {ital 1999} {ital The American Physical Society}

  17. DRUMS: a human disease related unique gene mutation search engine.

    PubMed

    Li, Zuofeng; Liu, Xingnan; Wen, Jingran; Xu, Ye; Zhao, Xin; Li, Xuan; Liu, Lei; Zhang, Xiaoyan

    2011-10-01

    With the completion of the human genome project and the development of new methods for gene variant detection, the integration of mutation data and its phenotypic consequences has become more important than ever. Among all available resources, locus-specific databases (LSDBs) curate one or more specific genes' mutation data along with high-quality phenotypes. Although some genotype-phenotype data from LSDB have been integrated into central databases little effort has been made to integrate all these data by a search engine approach. In this work, we have developed disease related unique gene mutation search engine (DRUMS), a search engine for human disease related unique gene mutation as a convenient tool for biologists or physicians to retrieve gene variant and related phenotype information. Gene variant and phenotype information were stored in a gene-centred relational database. Moreover, the relationships between mutations and diseases were indexed by the uniform resource identifier from LSDB, or another central database. By querying DRUMS, users can access the most popular mutation databases under one interface. DRUMS could be treated as a domain specific search engine. By using web crawling, indexing, and searching technologies, it provides a competitively efficient interface for searching and retrieving mutation data and their relationships to diseases. The present system is freely accessible at http://www.scbit.org/glif/new/drums/index.html.

  18. 29 CFR 1926.553 - Base-mounted drum hoists.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... located within easy reach of the operator's station. (3) Electric motor operated hoists shall be provided... 29 Labor 8 2010-07-01 2010-07-01 false Base-mounted drum hoists. 1926.553 Section 1926.553 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Cranes, Derricks, Hoists, Elevators, and...

  19. 29 CFR 1926.553 - Base-mounted drum hoists.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... located within easy reach of the operator's station. (3) Electric motor operated hoists shall be provided... 29 Labor 8 2011-07-01 2011-07-01 false Base-mounted drum hoists. 1926.553 Section 1926.553 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Helicopters, Hoists, Elevators, and...

  20. Flow Straightener for a Rotating-Drum Liquid Separator

    NASA Technical Reports Server (NTRS)

    O'Coin, James R.; Converse, David G.; Rethke, Donald W.

    2004-01-01

    A flow straightener has been incorporated into a rotary liquid separator that originally comprised an inlet tube, a shroud plate, an impeller, an inner drum, an outer drum, a housing, a pitot tube, and a hollow shaft motor. As a consequence of the original geometry of the impeller, shroud, inner drum, and hollow shaft, swirl was created in the airflow inside the hollow shaft during operation. The swirl speed was large enough to cause a significant pressure drop. The flow straightener consists of vanes on the back side of the shroud plate. These vanes compartmentalize the inside of the inner drum in such a way as to break up the flow path and thereby stop the air from swirling; as a result, the air enters the hollow shaft with a predominantly axial velocity instead of a swirl. Tests of the rotary liquid separator at an airflow rate of 10 cu ft/min (0.0047 cu m/s) revealed that the dynamic pressure drop was 8 in. of water (approx.=2 kPa) in the absence of the flow straightener and was reduced to 1 in. of water (approx.=0.25 kPa) in the presence of the flow straightener.

  1. Comparative Analysis of Cherenkov Light Detectors in an Oil Drum

    NASA Astrophysics Data System (ADS)

    Niduaza, Rexavalmar; Wedel, Zachary; Castro, Juan; Zavala, Favian; Fan, Sewan; Fatuzzo, Laura

    2014-03-01

    The multi-pixel photon counters (MPPC) has been used in a number of research development in astro-particle physics and particle physics. In an effort to further implement the MPPC detector, we constructed a modular experimental setup using a 16-inch tall acrylic cylinder filled with distilled water as the light producing medium to determine its feasibility as a possible detector for weak Cherenkov light. We have since progressed towards utilizing an oil drum (approximately 30 gallons) as our light-tight container replacing our prototype. In this talk, we would discuss the results regarding our investigation utilizing 1-inch and 3-inch photo-multiplier tubes (PMTs) in an oil drum as we did for our prototype. We would also present our experimental findings comparing our prototype and our oil drum setup using PMTs in coincidence with the MPPC coupled with wavelength-shifting fibers that are submerged in distilled water inside the oil drum vessel. Department of Education grant nymber P031S90007.

  2. Middle School Drum Ensemble: An Unlikely Experience in Classroom Democracy

    ERIC Educational Resources Information Center

    Barbre, James

    2013-01-01

    Though music has a long and successful history within education, it is often one of the first sacrificial lambs when school budgets tighten. Over the course of an academic year, a documentary film sought to tell the story of an American middle school drum ensemble. The context of this group provided an ideal way to examine the nature of student…

  3. Non-Destructive Assay of Curium Contaminated Transuranic Waste Drums

    SciTech Connect

    Foster, L.A.

    1998-11-01

    At the Plutonium Facility at Los Alamos National Laboratory, a series of non-destructive assays were performed on five transuranic waste (TRU) drums containing non-plutonium scrap metal that was potentially contaminated with weapons grade plutonium and trace quantities of curium. Typically, waste drums containing metal matrices are assayed for plutonium content using passive neutron coincidence counting techniques. The presence of trace quantities of Cm-244 prevents this type of analysis because of the strong coincidence signal created by spontaneous fission of Cm-244. To discriminate between the plutonium and curium materials present, an active neutron measurement technique was used. A Cf shuffler designed for measurement of uranium bearing materials was calibrated for plutonium in the active mode. The waste drums were then assayed for plutonium content in the shuffler using the active-mode calibration. The curium contamination levels were estimated from the difference between the active-mode measurement in the shuffler and a passive assay in a neutron coincidence counter. Far field gamma-ray measurements were made to identify additional radioactive contaminants and to corroborate the plutonium measurement results obtained from the active-mode assay. This report describes in detail the measurement process used for characterization of these waste drums. The measurement results and the estimated uncertainty will be presented.

  4. 4. VIEW TO SOUTHWEST OF SOUTH SIDE OF CENTER DRUM, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. VIEW TO SOUTHWEST OF SOUTH SIDE OF CENTER DRUM, ONE BULL SHAFT AND GEARS, BULL RING AND ROLLERS, AND TOP OF PIER III. WILLBRIDGE AND PORTLAND WEST HILLS IN BACKGROUND. - Burlington Northern Railroad Bridge, Spanning Willamette River at River Mile 6.9, Portland, Multnomah County, OR

  5. 14. BULL SHAFT, BULL RING AND PINION, AND DRUM. TOP ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. BULL SHAFT, BULL RING AND PINION, AND DRUM. TOP OF PIER III, GRANITE COPING, AND PLAIN CONCRETE PIER BELOW. DETAILS OF WEST PIER PROTECTION FRAMING AT PIER. WILLBRIDGE IN BACKGROUND. - Burlington Northern Railroad Bridge, Spanning Willamette River at River Mile 6.9, Portland, Multnomah County, OR

  6. 7 CFR 1434.8 - Containers and drums.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... REGULATIONS FOR HONEY § 1434.8 Containers and drums. (a)(1) To be eligible for assistance under this part, honey must be packed in: (i) CCC-approved, 5-gallon plastic containers; (ii) 5-gallon metal containers... Intermediate Bulk Containers (IBC's). (2) Honey stored in plastic containers must be determined safe and...

  7. 7 CFR 1434.8 - Containers and drums.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... REGULATIONS FOR HONEY § 1434.8 Containers and drums. (a)(1) To be eligible for assistance under this part, honey must be packed in: (i) CCC-approved, 5-gallon plastic containers; (ii) 5-gallon metal containers... Intermediate Bulk Containers (IBC's). (2) Honey stored in plastic containers must be determined safe and...

  8. Development of Interpersonal Coordination between Peers during a Drumming Task

    ERIC Educational Resources Information Center

    Endedijk, Hinke M.; Ramenzoni, Veronica C. O.; Cox, Ralf F. A.; Cillessen, Antonius H. N.; Bekkering, Harold; Hunnius, Sabine

    2015-01-01

    During social interaction, the behavior of interacting partners becomes coordinated. Although interpersonal coordination is well-studied in adults, relatively little is known about its development. In this project we explored how 2-, 3-, and 4-year-old children spontaneously coordinated their drumming with a peer. Results showed that all children…

  9. Velocity Profiles in a Rotating Drum: The Effects of Cohesion

    NASA Astrophysics Data System (ADS)

    Brewster, Robert C.; Silbert, Leonardo E.; Grest, Gary S.; Levine, Alex J.

    2007-03-01

    The dynamics of granular media in a rotating drum is important in a wide range of applications in industry associated with mixing granular materials. The rotating drum also serves as a standard experimental geometry to observe continuous avalanching in the laboratory. We study the effect of interparticle cohesion on the velocity field of the rotating drum using large scale granular dynamics simulations. Such cohesion is easily introduced in the system by a wetting fluid that forms menisci at interparticle contacts. Previously, we have examined the effect of interparticle cohesion in gravity driven chute flows, and have shown that the cohesion has a dramatic effect on the granular rheology. For strong enough cohesion, these forces generate a coherently moving plug at the free surface. In this talk, we examine the velocity profile in the rotating drum geometry in this plug-flow regime. We compare our results for angle of the pile in the continuous flow regime to the experiments of Nowak et al. [Nature Physics, 1 (2005)] and we examine the stress and velocity profile within the pile as well.

  10. 29 CFR 1926.553 - Base-mounted drum hoists.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 8 2014-07-01 2014-07-01 false Base-mounted drum hoists. 1926.553 Section 1926.553 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Helicopters, Hoists, Elevators, and...

  11. 29 CFR 1926.553 - Base-mounted drum hoists.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 8 2012-07-01 2012-07-01 false Base-mounted drum hoists. 1926.553 Section 1926.553 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Helicopters, Hoists, Elevators, and...

  12. 29 CFR 1926.553 - Base-mounted drum hoists.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 29 Labor 8 2013-07-01 2013-07-01 false Base-mounted drum hoists. 1926.553 Section 1926.553 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Helicopters, Hoists, Elevators, and...

  13. Occupational hygiene in a Finnish drum composting plant.

    PubMed

    Tolvanen, Outi; Nykänen, Jenni; Nivukoski, Ulla; Himanen, Marina; Veijanen, Anja; Hänninen, Kari

    2005-01-01

    Bioaerosols (microbes, dust and endotoxins) and volatile organic compounds (VOCs) were determined in the working air of a drum composting plant treating source-separated catering waste. Different composting activities at the Oulu drum composting plant take place in their own units separated by modular design and constructions. Important implication of this is that the control room is a relatively clean working environment and the risk of exposure to harmful factors is low. However, the number of viable airborne microbes was high both in the biowaste receiving hall and in the drum composting hall. The concentration (geometric average) of total microbes was 21.8 million pcs/m3 in the biowaste receiving hall, 13.9 million pcs/m3 in the drum composting hall, and just 1.4 million pcs/m3 in the control room. Endotoxin concentrations were high in the biowaste receiving hall and in the drum composting hall. The average (arithmetic) endotoxin concentration was over the threshold value of 200 EU/m3 in both measurement locations. In all working areas, the average (arithmetic) dust concentrations were in a low range of 0.6-0.7 mg/m3, being below the Finnish threshold value of 5 mg/m3. In the receiving hall and drum composting hall, the concentrations of airborne microbes and endotoxins may rise to levels hazardous to health during prolonged exposure. It is advisable to use a respirator mask (class P3) in these areas. Detected volatile organic compounds were typical compounds of composting plants: carboxylic acids and their esters, alcohols, ketones, aldehydes, and terpenes. Concentrations of VOCs were much lower than the Finnish threshold limit values (Finnish TLVs), many of the quantified compounds exceeded their threshold odour concentrations (TOCs). Primary health effects due VOCs were not presumable at these concentrations but unpleasant odours may cause secondary symptoms such as nausea and hypersensitivity reactions. This situation is typical of composting plants where

  14. EARLY TESTS OF DRUM TYPE PACKAGINGS - THE LEWALLEN REPORT

    SciTech Connect

    Smith, A.

    2010-07-29

    The need for robust packagings for radioactive materials (RAM) was recognized from the earliest days of the nuclear industry. The U.S. Department of Energy (DOE) Rocky Flats Plant developed a packaging for shipment of Pu in the early 1960's, which became the U.S. Department of Transportation (DOT) 6M specification package. The design concepts were employed in other early packagings. Extensive tests of these at Savannah River Laboratory (now Savannah River National Laboratory) were performed in 1969 and 1970. The results of these tests were reported in 'Drum and Board-Type Insulation Overpacks of Shipping Packages for Radioactive Materials', by E. E. Lewallen. The Lewallen Report was foundational to design of subsequent drum type RAM packaging. This paper summarizes this important early study of drum type packagings. The Lewallen Report demonstrated the ability packagings employing drum and insulation board overpacks and engineered containment vessels to meet the Type B package requirements. Because of the results of the Lewallen Report, package designers showed high concern for thermal protection of 'Celotex'. Subsequent packages addressed this by following strategies like those recommended by Lewallen and by internal metal shields and supplemental, encapsulated insulation disks, as in 9975. The guidance provide by the Lewallen Report was employed in design of a large number of drum size packagings over the following three decades. With the increased public concern over transportation of radioactive materials and recognition of the need for larger margins of safety, more sophisticated and complex packages have been developed and have replaced the simple packagings developed under the Lewallen Report paradigm.

  15. 7 CFR 160.201 - Fees generally for field inspection and certification of naval stores and drum containers of rosin.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... and incidental certification as to class, condition and weight). (i) In drums (see Note 1) per drum—$1... certified at any plant during any calendar month is equivalent to a total of 2,400 or more drums (counting five bags as equivalent to one drum), the fee shall be computed at the rate of $1.01 per drum and...

  16. CMR Shuffler System: Passive Mode Calibration and Certification Report

    SciTech Connect

    Frame, Katherine C.; Gomez, Cipriano D.; Salazar, William R.; Mayo, Douglas R.; Vigil, Georgiana M.; Crooks, William J.; Stange, Sy

    2012-07-20

    Los Alamos National Laboratory has a number of spherical confinement vessels (CVs) remaining from tests involving nuclear materials. These vessels have an inner diameter of 6 feet with 1 to 2 inch thick steel walls. The goal of the Confinement Vessel Disposition (CVD) project is to remove debris and reduce contamination inside the vessels. As debris is removed from the vessels, material will be placed in waste drums. Far-field gamma ray assay will be used to determine when a drum is nearing a {sup 239}Pu equivalent mass of less than 200 g. The drum will then be assayed using a waste drum shuffler operated in passive mode using a neutron coincidence counting method for accountability. This report focuses on the testing and calibration of the CMR waste drum shuffler in passive mode operation. Initial testing was performed to confirm previously accepted measurement parameters. The system was then calibrated using a set of weapons grade Pu (WGPu, {sup 239}Pu > 93%) oxide standards placed inside a 55 gallon drum. The calibration data ranges from Pu mass of 0.5 g to 188.9 g. The CMR waste drum shuffler has been tested and calibrated in passive mode in preparation for safeguards accountability measurements of waste drums containing material removed from CVs for the CVD project.

  17. Pipe overpack container for trasuranic waste storage and shipment

    DOEpatents

    Geinitz, Richard R.; Thorp, Donald T.; Rivera, Michael A.

    1999-01-01

    A Pipe Overpack Container for transuranic waste storage and shipment. The system consists of a vented pipe component which is positioned in a vented, insulated 55 gallon steel drum. Both the vented pipe component and the insulated drum are capable of being secured to prevent the contents from leaving the vessel. The vented pipe component is constructed of 1/4 inch stainless steel to provide radiation shielding. Thus, allowing shipment having high Americium-241 content. Several Pipe Overpack Containers are then positioned in a type B, Nuclear Regulatory Commission (NRC) approved, container. In the current embodiment, a TRUPACT-II container was employed and a maximum of fourteen Pipe Overpack Containers were placed in the TRUPACT-II. The combination received NRC approval for the shipment and storage of transuranic waste.

  18. Essential fatty acid requirement of juvenile red drum (Sciaenops ocellatus).

    PubMed

    Lochmann, R T; Gatlin, D M

    1993-10-01

    Feeding experiments and laboratory analyses were conducted to establish the essential fatty acid (EFA) requirement of red drum (Sciaenops ocellatus). Juvenile red drum were maintained in aquaria containing brackish water (5 ± 2‰ total dissolved solids) for two 6-week experiments. Semipurified diets contained a total of 70% lipid consisting of different combinations of tristearin [predominantly 18:0] and the following fatty acid ethyl esters: oleate, linoleate, linolenate, and a mixture of highly unsaturated fatty acids (HUFA) containing approximately 60% eicosapentaenoate plus docosahexaenoate. EFA-deficient diets (containing only tristearin or oleate) rapidly reduced fish growth and feed efficiency, and increased mortality. Fin erosion and a "shock syndrome" also occurred in association with EFA deficiency. Of the diets containing fatty acid ethyl esters, those with 0.5-1% (n-3) HUFA (0.3-0.6% eicosapentaenoate plus docosahexaenoate) promoted the best growth, survival, and feed efficiency; however, the control diet containing 7% menhaden fish oil provided the best performance. Excess (n-3) HUFA suppressed fish weight gain; suppression became evident at 1.5% (n-3) HUFA, and was pronounced at 2.5%. Fatty acid compositions of whole-body, muscle and liver tissues from red drum fed the various diets generally reflected dietary fatty acids, but modifications of these patterns also were evident. Levels of saturated fatty acids appeared to be regulated independent of diet. In fish fed EFA-deficient diets (containing only tristearin or oleate), monoenes increased and (n-3) HUFA were preferentially conserved in polar lipid fractions. Eicosatrienoic acid [20:3(n-9)] was not elevated in EFA-deficient red drum, apparently due to their limited ability to transform fatty acids. Red drum exhibited some limited ability to elongate and desaturate linoleic acid [18:2(n-6)] and linolenic acid [18:3(n-3)]; however, metabolism of 18:3(n-3) did not generally result in increased

  19. Closure report for Building 875 sump encased in concrete

    SciTech Connect

    Montemayor, W.

    1991-08-01

    This report will document the post-closure activities for the 875-R1U1 Waste-Solvent Underground Storage Tank located at Lawrence Livermore National Laboratory (LLNL), Site 300. The aforementioned tank waspreviously identified and registered with the California Water Resources Control Board as 875-31R. The underground tank system consists of a 55-gallon steel drum encased in concrete. The underground tank was used to collect dripping and spillage from the above-concrete drum rack storage area. The closure of this underground tank was permitted as Tank Identification No. 39-1945-21 by W.R. Snavely of SJCPHS-EHS. The last tank test, performed on February 1988, showed that the underground tank was leak tight. On May 1988, the sludge at the bottom of the tank was removed and disposed of as hazardous waste. The residual 1.5 inches of oily water in the tank was removed and the tank was washed with soap and water on December 11, 1989. The rinsate and residual sludge was disposed of as hazardous waste. The empty tank and the encasing concrete were extracted from the ground on November 5, 1990. No underground piping was associated with the removal of this underground tank since the tank was used to collect the dripping and spillage from the above-concrete drum rack. Three soil samples were collected in split tubes from approximately 1 foot below the bottom of the tank. The soil samples were collected and analyzed for Total Petroleum Hydrocarbon (TPH)-Gasoline, TPH-Diesel, Total Extractable Petroleum, Benzene, Toluene, Xylene, Ethyl Benzene, Tetraethyl Lead, Metals, Polychlorinated Biphenyls (PCB), and Ethylene Dibromide. Results indicated that the underground tank was leak tight. The concrete encasing was removed from the 55-gallon tank and disposed of as a municipal waste. The 55-gallon tank is currently stored at the Hazardous Waste Storage Area located in Lawrence Livermore National Laboratory, Livermore, California and is waiting as a hazardous waste.

  20. Gill morphometry of the red drum, Sciaenops ocellatus.

    PubMed

    Don Stevens, E

    1992-08-01

    The structure and morphometry of the gills of the marine teleost, red drum, have been studied. The present analysis of gas exchange area of fish gills is one of the most intensive and the results are compared to less intense averaging methods. Based on the gill area estimates, red drum falls into the category of a fish of intermediate activity. Its gill clearly has an exchange area less than that of the tunas, but is slightly greater than that of trout or bass. The three components that contribute to total exchange area (filament length, lamellar density, and area of individual lamellae) are not all greater in species with a greater total exchange area. The best correlate is total filament length.

  1. Low tension graphene drums for electromechanical pressure sensing

    NASA Astrophysics Data System (ADS)

    Patel, Raj N.; Mathew, John P.; Borah, Abhinandan; Deshmukh, Mandar M.

    2016-03-01

    We present a process to fabricate electromechanical pressure sensors using multilayer graphene in a sealed drum geometry. The drum resonators are fabricated on insulating sapphire substrates with a local back gate for direct radio frequency ({\\text{}}{{rf}}) actuation and detection of the mechanical modes. Using this scheme, we show the detection and electrostatic tuning of multiple resonant modes of the membrane up to 200 MHz. The geometry of the device also helps in attaining low tensile stress in the membrane, thereby giving high gate tunability (∼1 MHz/V) of the resonator modes. We study the resonant frequency shifts in the presence of helium gas and demonstrate a sensing capability of 1 Torr pressure in a cryogenic environment.

  2. A MODULAR STORE FOR DRUMS OF RADIOACTIVE WASTE

    SciTech Connect

    Sims, J.; Holden, G.

    2003-02-27

    Currently, the United Kingdom has no facility for the disposal of any waste above the low level category, indicating that all intermediate and high level waste, apart from spent fuel, has to be stored on the site of origin. To meet this storage requirement, nuclear sites are resorting to converting existing buildings or contemplating the construction of dedicated facilities, resulting in considerable cost implications. These financing aspects not only concern the construction strategy but also impinge on the ultimate decommissioning costs associated with each particular nuclear site. This paper reports on an investigation to apply the commercially available interlocking hollow block system to the design of a store for drums of radioactive waste. This block system can be quickly, and cost effectively, erected and filled with a choice of dense material. Later, the store can be dismantled with a minimum of disposable radioactive waste and the complete facility re - erected at another location if required, considerably reducing both capital construction and decommissioning costs. The investigation also encompassed a detailed review of the equipment required to place the drums of waste into the store, resulting in a scheme for a remotely operated vehicle that did not rely on umbilical control cables. The drum handler design included for 100% redundancy of all functions, meaning that whichever component failed, the handler was always recoverable to effect the necessary repair. The ultimate aim of the waste drum store review was to produce a facility that was as safe as a conventionally constructed unit, but at a lower overall building and decommissioning cost.

  3. 26. Detail view of drum girder with rollers below, resting ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    26. Detail view of drum girder with rollers below, resting on fixed turntable upon masonry center pier. Swing drive shaft (vertical) is turned by level gear of horizontal shaft (protruding through machine room wall), which turns pinion gear toothed to fixed turntable rack below rollers. (Nov. 25, 1988) - University Heights Bridge, Spanning Harlem River at 207th Street & West Harlem Road, New York County, NY

  4. Gas generation results and venting study for transuranic waste drums

    SciTech Connect

    Kazanjian, A.R.; Arnold, P.M.; Simmons, W.C.; D'Amico, E.L.

    1985-09-23

    Sixteen waste drums, containing six categories of plutonium-contaminated waste, were monitored for venting and gas generation for six months. The venting devices tested appeared adequate to relieve pressure and prevent hydrogen accumulation. Most of the gas generation, primarily H2 and CO2, was due to radiolytic decomposition of the hydrogenous wastes. Comparison of the gas yields with those obtained previously in laboratory tests showed very reasonable agreement with few exceptions.

  5. Contamination control aspects of attaching waste drums to the WIPP Waste Characterization Chamber

    SciTech Connect

    Rubick, L.M.; Burke, L.L.

    1998-12-31

    Argonne National Laboratory West (ANL-W) is verifying the characterization and repackaging of contact-handled transuranic (CH-TRU) mixed waste in support of the Waste Isolation Pilot Program (WIPP) project located in Carlsbad, New Mexico. The WIPP Waste Characterization Chamber (WCC) was designed to allow opening of transuranic waste drums for this process. The WCC became operational in March of 1994 and has characterized approximately 240 drums of transuranic waste. The waste drums are internally contaminated with high levels of transuranic radionuclides. Attaching and detaching drums to the glove box posed serious contamination control problems. Prior to characterizing waste, several drum attachment techniques and materials were evaluated. An inexpensive HEPA filter molded into the bagging material helps with venting during detachment. The current techniques and procedures used to attach and detach transuranic waste drums to the WCC are described.

  6. Waste drum gas generation sampling program at Rocky Flats during FY 1989

    SciTech Connect

    Roggenthen, D.K.; Nieweg, R.G.

    1990-10-01

    Rocky Flats Plant transuranic waste drums were sampled for gas composition. Glass, metal, graphite, and solidified inorganic sludge transuranic waste forms were sampled. A vacuum system was used to sample each layer of containment inside a waste drum, including individual waste bags. G values were calculated for the waste drums. G(H{sub 2}) was below 0.6 and G(Total) was below 1.3 for all waste forms discussed in this report. 5 refs., 3 figs., 3 tabs.

  7. Characterization of void volume VOC concentration in vented TRU waste drums. Final report

    SciTech Connect

    Liekhus, K.J.

    1995-08-01

    A test program has been conducted at the Idaho National Engineering Laboratory to demonstrate that the concentration of volatile organic compounds within the innermost layer of confinement in a vented waste drum can be estimated using a model incorporating diffusion and permeation transport principles and limited waste drum sampling data. This final report summarizes the experimental measurements and model predictions for transuranic waste drums containing solidified sludges and solid waste.

  8. Pharyngeal teeth of the freshwater drum (Aplodinotus grunniens) a predator of the zebra mussel (Dreissena polymorpha)

    USGS Publications Warehouse

    French, John R. P.

    1997-01-01

    The morphology of pharyngeal teeth of freshwater drum (Aplodinotus grunniens) was studied to determine changes that occur during growth of drum that may relate to consumption of zebra mussel (Dreissena polymorpha) by larger fish. Pharyngeal teeth were of three types. Cardiform teeth were replaced by villiform teeth, which were replaced by molariform teeth as the size class of drum increased. Molariform teeth comprised over 85% of total surface area of dentition in fish 265 mm long.

  9. Analysis of upper arm muscle activation using surface electromyography signals during drum playing

    PubMed Central

    Chong, Hyun Ju; Kwon, Chun-Ki; Kang, Hyun-Joo; Kim, Soo Ji

    2016-01-01

    This study measured surface electromyography of the biceps brachii and triceps brachii during repeated drum playing with and without a drumstick to better understand activation of the upper arm muscles and inform the use of instrument playing for motor rehabilitation. A total of 40 healthy college students participated in this study. All participants were asked to strike a drum with their hand and with a drumstick at three different levels of stroke: soft, medium, and strong. The stroke order was randomly assigned to participants. A sound level meter was used to record the intensity of the drum playing. Surface electromyography signals were recorded at every hit during drum playing both with and without the drumstick in each of the three stroke conditions. The results demonstrated that the highest muscle activation was observed in both biceps brachii and triceps brachii with strong drum playing with and without the drumstick. A two-way repeated measures analysis of variance showed that there was a significant main effect for stroke intensity in muscle activation and produced sound level. While higher activation of the triceps brachii was observed for drum playing without a drumstick, no significant differences were found between the biceps brachii and sound level. This study demonstrated via surface electromyography data that greater muscle activation of the biceps brachii and triceps brachii does not occur with the use of drumsticks in drum playing. With the drum sound controlled, drum playing by hand can be an effective therapeutic intervention for the upper arm muscles. PMID:27419114

  10. Modeling unsteady-state VOC transport in simulated waste drums. Revision 1

    SciTech Connect

    Liekhus, K.J.; Gresham, G.L.; Peterson, E.S.; Rae, C.; Hotz, N.J.; Connolly, M.J.

    1994-01-01

    This report is a revision of an EG&G Idaho informal report originally titled Modeling VOC Transport in Simulated Waste Drums. A volatile organic compound (VOC) transport model has been developed to describe unsteady-state VOC permeation and diffusion within a waste drum. Model equations account for three primary mechanisms for VOC transport from a void volume within the drum. These mechanisms are VOC permeation across a polymer boundary, VOC diffusion across an opening in a volume boundary, and VOC solubilization in a polymer boundary. A series of lab-scale experiments was performed in which the VOC concentration was measured in simulated waste drums under different conditions. A lab-scale simulated waste drum consisted of a sized-down 55-gal metal drum containing a modified rigid polyethylene drum liner. Four polyethylene bags were sealed inside a large polyethylene bag, supported by a wire cage, and placed inside the drum liner. The small bags were filled with VOC-air gas mixture and the VOC concentration was measured throughout the drum over a period of time. Test variables included the type of VOC-air gas mixtures introduced into the small bags, the small bag closure type, and the presence or absence of a variable external heat source. Model results were calculated for those trials where the permeability had been measured.

  11. EVALUATION OF RADIOLYSIS INDUCED HYDROGEN GENERATION IN DOT 6M DRUMS FROM INTEC

    SciTech Connect

    Vinson, D

    2007-06-18

    Three DOT 6M 30-gallon drums are scheduled to be shipped from the Idaho Nuclear Technology Engineering Center (INTEC) at the Idaho National Laboratory (INL) to L-Area at the Savannah River Site (SRS). These three drums contain radioactive materials that resulted from the material recovery effort following a small explosion that had occurred in the Idaho Chemical Processing Plant (ICPP) hot chemistry laboratory (HCL). In support of the shipment and subsequent storage of the three DOT 6M drums, an evaluation of the potential for molecular hydrogen production in the drums has been completed and documented herein. The potential sources of hydrogen evaluated in the current report include radiolytic decomposition of polymeric materials in the DOT 6M drums No.3031 and No.3598 and the radiolytic decomposition of water in drum No.20102. No other potential sources have been identified based upon reported drum contents and packaging configuration. A parametric approach was used to evaluate the maximum quantity of molecular hydrogen that can be expected to evolve in two DOT 6M 30-gallon drums in support of receipt and subsequent interim storage prior to canyon processing. These drums are two of three drums scheduled for shipment from INTEC to SRS as part of the decommissioning effort of the INTEC facility. The three DOT 6M drums will be received at L-Area in SRS and stored for up to 13-years prior to final disposition at HB-Line in 2020. Results of the current analysis do not include parametric analysis of drum No.20102 containing 114/133 SAL (salvage) which contains UO{sub 3} powder. This drum has not been identified as containing polymeric materials and a conservative calculation indicates that the maximum gross molecular hydrogen production due to the radiolysis of adsorbed moisture would yield a production rate of 5.1-cm{sup 3}/yr, driven primarily by the large surface are to volume ratio of the oxide powder. The remaining two drums, No.3031 and No.3598 contain polymer

  12. RESULTS OF ANALYSIS OF NGS CONCENTRATE DRUM SAMPLES [Next Generation Solvent

    SciTech Connect

    Peters, T.; Williams, M.

    2013-09-13

    Savannah River National Laboratory (SRNL) prepared two drums (50 gallons each in Drum#2 and Drum#4) of NGS-MCU (Next Generation Solvent-Modular CSSX Unit) concentrate for future use at MCU in downblending the BOBCalixC6 based solvent to produce NGS-MCU solvent. Samples of each drum were sent for analysis. The results of all the analyses indicate that the blend concentrate is of the correct composition and should produce a blended solvent at MCU of the desired formulation.

  13. Fort Drum integrated resource assessment. Volume 2, Baseline detail

    SciTech Connect

    Dixon, D.R.; Armstrong, P.R.; Brodrick, J.R.; Daellenbach, K.K.; Di Massa, F.V.; Keller, J.M.; Richman, E.E.; Sullivan, G.P.; Wahlstrom, R.R.

    1992-12-01

    The US Army Forces Command (FORSCOM) has tasked the Pacific Northwest Laboratory (PNL) as the lead laboratory supporting the US Department of Energy (DOE) Federal Energy Management Program`s mission to identify, evaluate, and assist in acquiring all cost-effective energy projects at Fort Drum. This is a model program PNL is designing for federal customers served by the Niagara Mohawk Power Company. It will identify and evaluate all electric and fossil fuel cost-effective energy projects; develop a schedule at each installation for project acquisition considering project type, size, timing, and capital requirements, as well as energy and dollar savings; and secure 100% of the financing required to implement electric energy efficiency projects from Niagara Mohawk and have Niagara Mohawk procure the necessary contractors to perform detailed audits and install the technologies. This report documents the assessment of baseline energy use at one of Niagara Mohawk`s primary federal facilities, the FORSCOM Fort Drum facility located near Watertown, New York. It is a companion report to Volume 1, the Executive Summary, and Volume 3, the Resource Assessment. This analysis examines the characteristics of electric, gas, oil, propane, coal, and purchased thermal capacity use for fiscal year (FY) 1990. It records energy-use intensities for the facilities at Fort Drum by building type and energy end use. It also breaks down building energy consumption by fuel type, energy end use, and building type. A complete energy consumption reconciliation is presented that includes the accounting of all energy use among buildings, utilities, central systems, and applicable losses.

  14. Thermal Neutron Die-Way-Time Studies for P and DGNAA of Radioactive Waste Drums at the MEDINA Facility

    SciTech Connect

    Mildenberger, Frank; Mauerhofer, Eric

    2015-07-01

    In Germany, radioactive waste with negligible heat production has to pass through a process of quality checking in order to check its conformance with national regulations prior to its transport, intermediate storage and final disposal. Additionally to its radioactive components, the waste may contain non-radioactive chemically toxic substances that can adversely affect human health and pollute the environment, especially the ground water. After an adequate decay time, the waste radioactivity will become harmless but the non-radioactive substances will persist over time. In principle, these hazardous substances may be quantified from traceability and quality controls performed during the production of the waste packages. As a consequence, a research and development program was initiated in 2007 with the aim to develop a nondestructive analytical technique for radioactive waste packages based on prompt and delayed gamma neutron activation analysis (P and DGNAA) employing a DT-neutron generator in pulsed mode. In a preliminary study it was experimentally demonstrated that P and DGNAA is suitable to determine the chemical composition of large samples. In 2010 a facility called MEDINA (Multi Element Detection based on Instrumental Neutron Activation) was developed for the qualitative and quantitative determination of nonradioactive, toxic elements and substances in 200-l steel drums. The determination of hazardous substances and elements is generally achieved measuring the prompt gamma-rays induced by thermal neutrons. Additional information about the composition of the waste matrix could be derived measuring the delayed gamma-rays from short life activation products. However a sensitive detection of these delayed gamma-rays requires that thermal neutrons have almost vanished. Therefore, the thermal neutron die-away-time has to be known in order to achieve an optimal discrimination between prompt and delayed gamma-ray spectra acquisition. Measurements Thermal neutron

  15. A Mini-Atlas of Ear-drum Pathology

    PubMed Central

    Hawke, Michael; Kwok, Peter

    1987-01-01

    The authors provide a number of ear-drum pictures and identify and discuss diseases affecting the external ear canal, the tympanic membrane and middle ear. They also deal with the removal of foreign bodies from the external canal, perforation of the tympanic membrane, and the use of an artificial ventilation tube. ImagesFig. 1Fig. 2Fig. 3Fig. 4Fig. 5Fig. 6Fig. 7Fig. 8Fig. 9Fig. 10Fig. 11Fig. 12Fig. 13Fig. 14Fig. 15Fig. 16Fig. 17Fig. 18 PMID:21263886

  16. Habitat Suitability Index Models: Larval and juvenile red drum

    USGS Publications Warehouse

    Buckley, Jack

    1984-01-01

    A review and synthesis of existing information were used to develop a habitat model for larval and juvenile red drum. The model is scaled to produce an index of habitat suitability between 0 (unsuitable habitat) and 1 (optimally suitable habitat) for estuarine areas along the Gulf of Mexico and Atlantic coasts. Habitat suitability indices are designed for use with habitat evaluation procedures developed by the U.S. Fish and Wildlife Service. Guidelines for model application and techniques for estimating model variables are provided.

  17. An autonomous mobil robot to perform waste drum inspections

    SciTech Connect

    Peterson, K.D.; Ward, C.R.

    1994-03-01

    A mobile robot is being developed by the Savannah River Technology Center (SRTC) Robotics Group of Westinghouse Savannah River company (WSRC) to perform mandated inspections of waste drums stored in warehouse facilities. The system will reduce personnel exposure and create accurate, high quality documentation to ensure regulatory compliance. Development work is being coordinated among several DOE, academic and commercial entities in accordance with DOE`s technology transfer initiative. The prototype system was demonstrated in November of 1993. A system is now being developed for field trails at the Fernald site.

  18. Color image digitization and analysis for drum inspection

    SciTech Connect

    Muller, R.C.; Armstrong, G.A.; Burks, B.L.; Kress, R.L.; Heckendorn, F.M.; Ward, C.R.

    1993-05-01

    A rust inspection system that uses color analysis to find rust spots on drums has been developed. The system is composed of high-resolution color video equipment that permits the inspection of rust spots on the order of 0.25 cm (0.1-in.) in diameter. Because of the modular nature of the system design, the use of open systems software (X11, etc.), the inspection system can be easily integrated into other environmental restoration and waste management programs. The inspection system represents an excellent platform for the integration of other color inspection and color image processing algorithms.

  19. Macroencapsulation development at Pantex

    SciTech Connect

    Yokum, J.S.

    1995-12-31

    The Pantex Plant is developing an innovative skid-mounted macroencapsulation technology (called a mobile treatment unit, MTU) that will economically dispose low-level radioactive mixed waste debris. Pantex`s macroencapuslation technology spin-welds a polyethylene top onto a polyethylene receiver to form a jacket that encapsulates a fifty-five (55) gallon steel drum of compacted low-level radioactive and mixed waste debris. The annulus formed by the fifty-five gallon drum and the polyethylene jacket is filled with a material (either foam or grout) to eliminate voids in the final waste form. The US EPA verified that the use of a polyethylene jacket constitutes macroencapsulation in a letter to Chemical Waste Management, Inc., dated September 19, 1995. The EPA letter stipulated that this treatment technology should not be used for D008, radioactive lead solids, and that the final waste form should be structurally sound and resistant to degradation.

  20. APPLICATION OF NONSPHERICAL FISSILE CONFIGURATION IN WASTE CONTAINERS AT SRS

    SciTech Connect

    Eghbali, D; Michelle Abney, M

    2007-01-03

    Transuranic (TRU) solid waste that has been generated as a result of the production of nuclear material for the United States defense program at the Savannah River Site (SRS) has been stored in more than 30,000 55-gallon drums and carbon steel boxes since 1953. Nearly two thirds of those containers have been processed and shipped to the Waste Isolation Pilot Plant. Among the containers assayed so far, the results indicate several drums with fissile inventories significantly higher (600-1000 fissile grams equivalent (FGE) {sup 239}Pu) than their original assigned values. While part of this discrepancy can be attributed to the past limited assay capabilities, human errors are believed to be the primary contributor. This paper summarizes the application of nonspherical fissile material configuration in waste containers, resulting in less restrictive mass and spacing limits, increased storage capacity, and several administrative controls for handling and storage of waste containers being modified without compromising safety.

  1. PROBABILISTIC ASSESSMENT OF A CRITICALITY IN A WASTE CONTAINER AT SRS

    SciTech Connect

    Eghbali, D

    2006-12-26

    Transuranic solid waste that has been generated as a result of the production of nuclear material for the United States defense program at the Savannah River Site (SRS) has been stored in more than 30,000 55-gallon drums and various size carbon steel boxes since 1953. Nearly two thirds of those containers have been processed and shipped to the Waste Isolation Pilot Plant. Among the containers assayed so far, the results indicate several drums with fissile inventories significantly higher (600-1000 grams {sup 239}Pu) than their original assigned values. While part of this discrepancy can be attributed to the past limited assay capabilities, human errors are believed to be the primary contributor. This paper summarizes an assessment of the probability of occurrence of a criticality accident during handling of the remaining transuranic waste containers at SRS.

  2. Nondestructive Analysis of MET-5 Drum at TA35 Building 2 A-Wing Vault.

    SciTech Connect

    Desimone, David J.; Vo, Duc Ta

    2016-11-03

    Measurements using a mechanically cooled portable high purity germanium HPGe Ortec detective were taken of a type B drum Serial number R-1157 to determine if any radioactive material was inside. The Drum, R-1157, spectrum was analyzed using PeakEasy 4.84 and a visual look at the spectrum showed background radiation.

  3. Improvement of Algorithms for Pressure Maintenance Systems in Drum-Separators of RBMK-1000 Reactors

    SciTech Connect

    Aleksakov, A. N. Yankovskiy, K. I.; Dunaev, V. I.; Kushbasov, A. N.

    2015-05-15

    The main tasks and challenges for pressure regulation in the drum-separators of RBMK-1000 reactors are described. New approaches to constructing algorithms for pressure control in drum-separators by electro-hydraulic turbine control systems are discussed. Results are provided from tests of the operation of modernized pressure regulators during fast transients with reductions in reactor power.

  4. 40 CFR 417.180 - Applicability; description of the manufacture of drum dried detergents subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... manufacture of drum dried detergents subcategory. 417.180 Section 417.180 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Drum Dried Detergents Subcategory § 417.180...

  5. 40 CFR 417.180 - Applicability; description of the manufacture of drum dried detergents subcategory.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... manufacture of drum dried detergents subcategory. 417.180 Section 417.180 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Drum Dried Detergents Subcategory § 417.180...

  6. 40 CFR 417.180 - Applicability; description of the manufacture of drum dried detergents subcategory.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... manufacture of drum dried detergents subcategory. 417.180 Section 417.180 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Drum Dried Detergents Subcategory § 417.180...

  7. 40 CFR 417.180 - Applicability; description of the manufacture of drum dried detergents subcategory.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... manufacture of drum dried detergents subcategory. 417.180 Section 417.180 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Drum Dried Detergents Subcategory § 417.180...

  8. 40 CFR 417.180 - Applicability; description of the manufacture of drum dried detergents subcategory.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... manufacture of drum dried detergents subcategory. 417.180 Section 417.180 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SOAP AND DETERGENT MANUFACTURING POINT SOURCE CATEGORY Manufacture of Drum Dried Detergents Subcategory § 417.180...

  9. Electric-stepping-motor tests for a control-drum actuator of a nuclear reactor

    NASA Technical Reports Server (NTRS)

    Kieffer, A. W.

    1972-01-01

    Experimental tests were conducted on two stepping motors for application as reactor control-drum actuators. Various control-drum loads with frictional resistances ranging from approximately zero to 40 N-m and inertias ranging from zero to 0.424 kg-sq m were tested.

  10. 77 FR 8255 - Constitution Road Drum Superfund Site, Atlanta, Dekalb County, GA; Notice of Settlement

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-14

    ... Response, Compensation and Liability Act (CERCLA), the United States Environmental Protection Agency has entered into a settlement for past response costs concerning the Constitution Road Drum Superfund Site... AGENCY Constitution Road Drum Superfund Site, Atlanta, Dekalb County, GA; Notice of Settlement...

  11. 77 FR 2981 - Constitution Road Drum Superfund Site; Atlanta, Dekalb County, GA; Notice of Settlement

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-20

    ... Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), the United States Environmental Protection Agency has entered into a settlement for past response costs concerning the Constitution Road Drum... AGENCY Constitution Road Drum Superfund Site; Atlanta, Dekalb County, GA; Notice of Settlement...

  12. Monkey drumming reveals common networks for perceiving vocal and nonvocal communication sounds.

    PubMed

    Remedios, Ryan; Logothetis, Nikos K; Kayser, Christoph

    2009-10-20

    Salient sounds such as those created by drumming can serve as means of nonvocal acoustic communication in addition to vocal sounds. Despite the ubiquity of drumming across human cultures, its origins and the brain regions specialized in processing such signals remain unexplored. Here, we report that an important animal model for vocal communication, the macaque monkey, also displays drumming behavior, and we exploit this finding to show that vocal and nonvocal communication sounds are represented by overlapping networks in the brain's temporal lobe. Observing social macaque groups, we found that these animals use artificial objects to produce salient periodic sounds, similar to acoustic gestures. Behavioral tests confirmed that these drumming sounds attract the attention of listening monkeys similarly as conspecific vocalizations. Furthermore, in a preferential looking experiment, drumming sounds influenced the way monkeys viewed their conspecifics, suggesting that drumming serves as a multimodal signal of social dominance. Finally, by using high-resolution functional imaging we identified those brain regions preferentially activated by drumming sounds or by vocalizations and found that the representations of both these communication sounds overlap in caudal auditory cortex and the amygdala. The similar behavioral responses to drumming and vocal sounds, and their shared neural representation, suggest a common origin of primate vocal and nonvocal communication systems and support the notion of a gestural origin of speech and music.

  13. Bringing Carnaval Drum and Dance Traditions into 4-H Programming for Latino Youth

    ERIC Educational Resources Information Center

    Conklin-Ginop, Evelyn; Braverman, Marc T.; Caruso, Robyn; Bone, Dennis

    2011-01-01

    4-H Bloco Drum and Dance is an afterschool program that teaches adolescents drumming, dancing, and theater arts in the rich traditions of Brazilian Carnaval. Teens learn to express themselves in a variety of modalities and perform at community events. The program was developed by a community coalition that included 4-H, other youth programs, and…

  14. The effect of zebra mussel consumption on growth of freshwater drum in Lake Erie

    USGS Publications Warehouse

    French, John R. P.; Bur, Michael T.

    1996-01-01

    We examined food habits and scale annuli of freshwater drum (Aplodinotus grunniens) from western Lake Erie to determine whether increasing predation on zebra mussels (Dreissena polymorpha) had affected growth of freshwater drum. The volume of zebra mussels in drum guts was greater in older fish. Growth of age classes 3–4, which consumed few zebra mussels, was greater in the most productive year for zebra mussels, July 1990–August 1991, than in three prior years. The total lengths of 5-year-old drum changed little. The mean total length of 6-year-old females has declined since the zebra mussel invaded Lake Erie, even through mussels comprised more than two-thirds of gut samples in these fish. These studies suggest that zebra mussels may not benefit freshwater drum when serving as a staple in the diet. PDF

  15. Handling 78,000 drums of mixed-waste sludge

    SciTech Connect

    Berry, J.B.; Harrington, E.S.; Mattus, A.J.

    1991-01-01

    The Oak Ridge Gaseous Diffusion Plant (now known as the Oak Ridge K-25 Site) closed two mixed-waste surface impoundments by removing the sludge and contaminated pond-bottom clay and attempting to process it into durable, nonleachable, concrete monoliths. Interim, controlled, above-ground storage included delisting the stabilized sludge from hazardous to nonhazardous and disposing of the delisted monoliths as Class 1 radioactive waste. Because of schedule constraints and process design and control deficiencies, {approximately}46,000 drums of material in various stages of solidification and {approximately}32,000 barrels of unprocessed sludge are stored. The abandoned treatment facility still contains {approximately}16,000 gal of raw sludge. Such storage of mixed waste does not comply with the Resource Conservation and Recovery Act (RCRA) guidelines. This paper describes actions that are under way to bring the storage of {approximately}78,000 drums of mixed waste into compliance with RCRA. Remediation of this problem by treatment to meet regulatory requirements is the focus of the discussion. 3 refs., 2 figs., 4 tabs.

  16. The granular mixing in a slurry rotating drum

    NASA Astrophysics Data System (ADS)

    Liao, C. C.; Hsiau, S. S.

    2010-03-01

    The mixing dynamics of granular materials immersed in a liquid was experimentally studied in a quasi-2D rotating drum. A DV (SONY DCR-TRV900 NTSC) motion corder analyzer was used to record the motions of granular materials. The effects of interstitial fluid viscosity and filling degree on the mixing index, mixing rate constant, and dynamic repose angle in the rotating drum were investigated and discussed in this paper. The experimental results show that the interstitial fluid viscosity has almost not influence on the final stable mixing index but has significantly effects on the mixing rate constant and dynamic repose angle in slurry granular flows. The results show that the mixing rate and dynamic repose angle increase with increasing the interstitial fluid viscosity. The results also indicate that the filling degree plays an important role in mixing dynamics in slurry granular flows. The mixing rate constant is demonstrated to be decreased with increasing the filling degree. The dynamic repose angle is not altered by the filling degree. Finally, we find that the dynamic repose angle and the mixing rate constant increase slightly at high Stokes number and increase dramatically at low Stokes number with decreasing Stokes number.

  17. Rotary drum composting of vegetable waste and tree leaves.

    PubMed

    Kalamdhad, Ajay S; Singh, Yatish K; Ali, Muntjeer; Khwairakpam, Meena; Kazmi, A A

    2009-12-01

    High rate composting studies on institutional waste, i.e. vegetable wastes, tree leaves, etc., were conducted on a demonstration-scale (3.5 m(3)) rotary drum composter by evaluating changes in some physico-chemical and biological parameters. During composting, higher temperature (60-70 degrees C) at inlet zone and (50-60 degrees C) at middle zone were achieved which resulted in high degradation in the drum. As a result, all parameters including TOC, C/N ratio, CO(2) evolution and coliforms were decreased significantly within few days of composting. Within a week period, quality compost with total nitrogen (2.6%) and final total phosphorus (6 g/kg) was achieved; but relatively higher final values of fecal coliforms and CO(2) evolution, suggested further maturation. Thus, two conventional composting methods namely windrow (M1) and vermicomposting (M2) tried for maturation of primary stabilized compost. By examining these methods, it was suggested that M2 was found suitable in delivering fine grained, better quality matured compost within 20 days of maturation period.

  18. Validation testing of radioactive waste drum filter vents

    SciTech Connect

    Weber, L.D.; Rahimi, R.S.; Edling, D.

    1997-08-01

    The minimum requirements for Drum Filter Vents (DFVs) can be met by demonstrating conformance with the Waste Isolation Pilot Plant (WIPP) Trupact II Safety Assessment Report (SAR), and conformance with U.S. Federal shipping regulations 49 CFR 178.350, DOT Spec 7A, for Type A packages. These together address a number of safety related performance parameters such as hydrogen diffusivity, flow related pressure drop, filtration efficiency and, separately, mechanical stability and the ability to prevent liquid water in-leakage. In order to make all metal DFV technology (including metallic filter medium) available to DOE sites, Pall launched a product development program to validate an all metal design to meet these requirements. Numerous problems experienced by DOE sites in the past came to light during this development program. They led us to explore enhancements to DFV design and performance testing addressing these difficulties and concerns. The result is a patented all metal DFV certified to all applicable regulatory requirements, which for the first time solves operational and health safety problems reported by DOE site personnel but not addressed by previous DFV`s. The new technology facilitates operations (such as manual, automated and semi-automated drum handling/redrumming), sampling, on-site storage, and shipping. At the same time, it upgrades filtration efficiency in configurations documented to maintain filter efficiency following mechanical stress. 2 refs., 2 figs., 10 tabs.

  19. 76 FR 44912 - Callaway and Son Drum Service Superfund Site; Lake Alfred, Polk County, FL; Notice of Settlement

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-27

    .... Submit your comments by Site name Callaway and Son Drum Service Superfund Site by one of the following...] Callaway and Son Drum Service Superfund Site; Lake Alfred, Polk County, FL; Notice of Settlement AGENCY... concerning the Callaway and son Drum Service Superfund Site located in Lake Alfred, Polk County, Florida...

  20. 40 CFR 265.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... hazardous waste in overpacked drums (lab packs). 265.316 Section 265.316 Protection of Environment... small containers of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste in overpacked drums (lab packs) may be placed in a landfill if the following requirements are met:...

  1. 40 CFR 264.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... hazardous waste in overpacked drums (lab packs). 264.316 Section 264.316 Protection of Environment... of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste in overpacked drums (lab packs) may be placed in a landfill if the following requirements are met: (a) Hazardous...

  2. 40 CFR 264.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... hazardous waste in overpacked drums (lab packs). 264.316 Section 264.316 Protection of Environment... of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste in overpacked drums (lab packs) may be placed in a landfill if the following requirements are met: (a) Hazardous...

  3. 40 CFR 265.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... hazardous waste in overpacked drums (lab packs). 265.316 Section 265.316 Protection of Environment... small containers of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste in overpacked drums (lab packs) may be placed in a landfill if the following requirements are met:...

  4. 40 CFR 265.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... hazardous waste in overpacked drums (lab packs). 265.316 Section 265.316 Protection of Environment... small containers of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste in overpacked drums (lab packs) may be placed in a landfill if the following requirements are met:...

  5. 40 CFR 264.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... hazardous waste in overpacked drums (lab packs). 264.316 Section 264.316 Protection of Environment... of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste in overpacked drums (lab packs) may be placed in a landfill if the following requirements are met: (a) Hazardous...

  6. 40 CFR 264.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... hazardous waste in overpacked drums (lab packs). 264.316 Section 264.316 Protection of Environment... of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste in overpacked drums (lab packs) may be placed in a landfill if the following requirements are met: (a) Hazardous...

  7. 40 CFR 265.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... hazardous waste in overpacked drums (lab packs). 265.316 Section 265.316 Protection of Environment... small containers of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste in overpacked drums (lab packs) may be placed in a landfill if the following requirements are met:...

  8. Granular flow in a rotating drum: Experiments and theory

    NASA Astrophysics Data System (ADS)

    Hung, C. Y.; Stark, C. P.; Capart, H.; Li, L.; Smith, B.; Grinspun, E.

    2015-12-01

    Erosion at the base of a debris flow fundamentally controls how large the flow will become and how far it will travel. Experimental observations of this important phenomenon are rather limited, and this lack has led theoretical treatments to making ad hoc assumptions about the basal process. In light of this, we carried out a combination of laboratory experiments and theoretical analysis of granular flow in a rotating drum, a canonical example of steady grain motion in which entrainment rates can be precisely controlled. Our main result is that basal sediment is entrained as the velocity profile adjusts to imbalance in the flow of kinetic energy.Our experimental apparatus consisted of a 40cm-diameter drum, 4cm-deep, half-filled with 2.3mm grains. Rotation rates varied from 1-70 rpm. We varied the effective scale by varying effective gravity from 1g to 70g on a geotechnical centrifuge. The field of grain motion was recorded using high-speed video and mapped using particle tracking velocimetry. In tandem we developed a depth-averaged theory using balance equations for mass, momentum and kinetic energy. We assumed a linearized GDR Midi granular rheology [da Cruz, 2005] and a Coulomb friction law along the sidewalls [Jop et al., 2005]. A scaling analysis of our equations yields a dimensionless "entrainment number" En, which neatly parametrizes the flow geometry in the drum for a wide range of variables, e.g., rotation rate and effective gravity. At low En, the flow profile is planar and kinetic energy is balanced locally in the flow layer. At high En, the flow profile is sigmoidal (yin-yang shaped) and the kinetic energy is dominated by longitudinal, streamwise transfer. We observe different scaling behavior under each of these flow regimes, e.g., between En and kinetic energy, surface slope and flow depth. Our theory correctly predicts their scaling exponents and the value of En at which the regime transition takes place. We are also able to make corrections for

  9. Variation in movement patterns of red drum (Sciaenops ocellatus) inferred from conventional tagging and ultrasonic telemetry

    USGS Publications Warehouse

    Bacheler, N.M.; Paramore, L.M.; Burdick, S.M.; Buckel, J.A.; Hightower, J.E.

    2009-01-01

    We used 25 years of conventional tagging data (n=6173 recoveries) and 3 years of ultrasonic telemetry data (n=105 transmitters deployed) to examine movement rates and directional preferences of four age classes of red drum (Sciaenops ocellatus) in estuarine and coastal waters of North Carolina. Movement rates of conventionally tagged red drum were dependent on the age, region, and season of tagging. Age-1 and age-2 red drum tagged along the coast generally moved along the coast, whereas fish tagged in oligohaline waters far from the coast were primarily recovered in coastal regions in fall months. Adult (age-4+) red drum moved from overwintering grounds on the continental shelf through inlets into Pamlico Sound in spring and summer months and departed in fall. Few tagged red drum were recovered in adjacent states (0.6% of all recoveries); however, some adult red drum migrated seasonally from overwintering grounds in coastal North Carolina northward to Virginia in spring, returning in fall. Age-2 transmittertracked red drum displayed seasonal emigration from a small tributary, but upstream and downstream movements within the tributary were correlated with fluctuating salinity regimes and not season. Large-scale conventional tagging and ultrasonic telemetry programs can provide valuable insights into the complex movement patterns of estuarine fish.

  10. Passive neutron design study for 200-L waste drums

    SciTech Connect

    Menlove, H.O.; Beddingfield, D.B.; Pickrell, M.M.

    1997-09-01

    We have developed a passive neutron counter for the measurement of plutonium in 200-L drums of scrap and waste. The counter incorporates high efficiency for the multiplicity counting in addition to the traditional coincidence counting. The {sup 252}Cf add-a-source feature is used to provide an accurate assay over a wide range of waste matrix materials. The room background neutron rate is reduced by using 30 cm of external polyethylene shielding and the cosmic-ray background is reduced by statistical filtering techniques. Monte Carlo Code calculations were used to determine the optimum detector design, including the gas pressure, size, number, and placement of the {sup 3}He tubes in the moderator. Various moderators, including polyethylene, plastics, teflon, and graphite, were evaluated to obtain the maximum efficiency and minimum detectable mass of plutonium.

  11. The Telescope Array Middle Drum fluorescence detector simulation on GPUs

    NASA Astrophysics Data System (ADS)

    Abu-Zayyad, Tareq; Telescope-Array Collaboration

    2014-06-01

    In recent years, the Graphics Processing Unit (GPU) has been recognized and widely used as an accelerator for many scientific calculations. In general, problems amenable to parallelization are ones that benefit most from the use of GPUs. The Monte Carlo simulation of fluorescence detector response to air showers presents many opportunities for parallelization. In this paper we report on a Monte Carlo program used for the simulation of the Telescope Array Fluorescence Detector located at the Middle Drum site which uses GPU acceleration. All of the physics simulation from shower development, light production and atmospheric attenuation, as well as, the realistic detector optics and electronics simulations are done on the GPU. A detailed description of the code implementation is given, and results on the accuracy and performance of the simulation are presented as well. Improvements in computational throughput in excess of 50× are reported and the accuracy of the results is on par with the CPU implementation of the simulation.

  12. Continuum theory of axial segregation in a long rotating drum

    SciTech Connect

    Aranson, I.S.; Vinokur, V.M.; Tsimring, L.S.

    1999-08-01

    We develop a continuum description for the axial segregation of granular materials in a long rotating drum based on the dynamics of the thin near-surface granular flow coupled to bulk flow. The equations of motion are reduced to the one-dimensional system for two local variables only, the concentration difference and the dynamic angle of repose, or the average slope of the free surface. The parameters of the system are established from comparison with experimental data. The resulting system describes both initial transient traveling wave dynamics and the formation of quasi-stationary bands of segregated materials. A long-term evolution proceeds through slow logarithmic coarsening of the band structure which is analogous to the spinoidal decomposition described by the Cahn-Hilliard equation. {copyright} {ital 1999} {ital The American Physical Society}

  13. Time domain simulation and sound synthesis for the snare drum.

    PubMed

    Bilbao, Stefan

    2012-01-01

    The snare drum is a complex system, relying on the interaction of multiple components: the drumheads, or membranes, a set of snares, the surrounding acoustic field and an internal cavity. Because these components are multidimensional, and due to a strong distributed non-linearity (the snare interaction), many techniques used frequently in physical modeling synthesis applications, such as digital waveguides and modal methods are difficult to apply. In this article, finite difference time domain techniques are applied to a full 3D system, and various features of interest, such as the coupling between membranes, and the interaction between the membranes and the snares, are examined in detail. Also discussed are various numerical features, such as spurious splitting of degenerate modes and bandwidth limitation, and estimates of computational complexity are provided. Sound examples are presented.

  14. Analysis of natural gas supply strategies at Fort Drum

    SciTech Connect

    Stucky, D.J.; Shankle, S.A.; Anderson, D.M.

    1992-07-01

    This analysis investigates strategies for Fort Drum to acquire a reliable natural gas supply while reducing its gas supply costs. The purpose of this study is to recommend an optimal supply mix based on the life-cycle costs of each strategy analyzed. In particular, this study is intended to provide initial guidance as to whether or not the building and operating of a propane-air mixing station is a feasible alternative to the current gas acquisition strategy. The analysis proceeded by defining the components of supply (gas purchase, gas transport, supplemental fuel supply); identifying alternative options for each supply component; constructing gas supply strategies from different combinations of the options available for each supply component and calculating the life-cycle costs of each supply strategy under a set of different scenarios reflecting the uncertainty of future events.

  15. MULTIPLE INPUT BINARY ADDER EMPLOYING MAGNETIC DRUM DIGITAL COMPUTING APPARATUS

    DOEpatents

    Cooke-Yarborough, E.H.

    1960-12-01

    A digital computing apparatus is described for adding a plurality of multi-digit binary numbers. The apparatus comprises a rotating magnetic drum, a recording head, first and second reading heads disposed adjacent to the first and second recording tracks, and a series of timing signals recorded on the first track. A series of N groups of digit-representing signals is delivered to the recording head at time intervals corresponding to the timing signals, each group consisting of digits of the same significance in the numbers, and the signal series is recorded on the second track of the drum in synchronism with the timing signals on the first track. The multistage registers are stepped cyclically through all positions, and each of the multistage registers is coupled to the control lead of a separate gate circuit to open the corresponding gate at only one selected position in each cycle. One of the gates has its input coupled to the bistable element to receive the sum digit, and the output lead of this gate is coupled to the recording device. The inputs of the other gates receive the digits to be added from the second reading head, and the outputs of these gates are coupled to the adding register. A phase-setting pulse source is connected to each of the multistage registers individually to step the multistage registers to different initial positions in the cycle, and the phase-setting pulse source is actuated each N time interval to shift a sum digit to the bistable element, where the multistage register coupled to bistable element is operated by the phase- setting pulse source to that position in its cycle N steps before opening the first gate, so that this gate opens in synchronism with each of the shifts to pass the sum digits to the recording head.

  16. A genetic linkage map of red drum, Sciaenops ocellatus.

    PubMed

    Portnoy, D S; Renshaw, M A; Hollenbeck, C M; Gold, J R

    2010-12-01

    Second-generation, sex-specific genetic linkage maps were generated for the economically important estuarine-dependent marine fish Sciaenops ocellatus (red drum). The maps were based on F(1) progeny from each of two single-pair mating families. A total of 237 nuclear-encoded microsatellite markers were mapped to 25 linkage groups. The female map contained 226 markers, with a total length of 1270.9 centiMorgans (cM) and an average inter-marker interval of 6.53 cM; the male map contained 201 markers, with a total length of 1122.9 cM and an average inter-marker interval of 6.03 cM. The overall recombination rate was approximately equal in the two sexes (♀:♂=1.03:1). Recombination rates in a number of linkage intervals, however, differed significantly between the same sex in both families and between sexes within families. The former occurred in 2.4% of mapped intervals, while the latter occurred in 51.2% of mapped intervals. Sex-specific recombination rates varied within chromosomes, with regions of both female-biased and male-biased recombination. Original clones from which the microsatellite markers were generated were compared with genome sequence data for the spotted green puffer, Tetraodon nigroviridis; a total of 43 matches were located in 17 of 21 chromosomes of T. nigroviridis, while seven matches were in unknown portions of the T. nigroviridis genome. The map for red drum provides a new, useful tool for aquaculture, population genetics, and comparative genomics of this economically important marine species.

  17. Aircraft Steels

    DTIC Science & Technology

    2009-02-19

    NAWCADPAX/TR-2009/ 12 AIRCRAFT STEELS by E. U. Lee R. Taylor C. Lei H. C. Sanders 19 February 2009...MARYLAND NAWCADPAX/TR-2009/ 12 19 February 2009 AIRCRAFT STEELS by E. U. Lee R. Taylor C. Lei H. C. Sanders...Prescribed by ANSI Std. Z39-18 NAWCADPAX/TR-2009/ 12 ii SUMMARY Five high strength and four stainless steels have been studied, identifying their

  18. Plasma Glucose Levels for Red Drum Sciaenops Ocellatus in a Florida Estuarine Fisheries Reserve

    NASA Technical Reports Server (NTRS)

    Bourtis, Carla M.; Francis-Floyd, Ruth; Boggs, Ashley S P.; Reyier, Eric A.; Stolen, Eric D.; Yanong, Roy P.; Guillette, Louis J., Jr.

    2015-01-01

    Despite the significant value of the southeastern United States' red drum (Sciaenops ocellatus) fishery, there is a lack of clinical blood chemistry data. This was the first study to assess plasma glucose values as an indicator of stress response to evaluate variation and the effect of reproductive activity for wild adult red drum in Florida. Red drum (n=126) were collected from NASA's Kennedy Space Center waters during three reproductive periods in 2011. Samples were obtained from the branchial vessels of the gill arch. Plasma glucose levels were significantly different among reproductive periods, with the highest mean values recorded during the spawning period, September- October (38.23 mg / dL +/- 10.0). The glucose range was 17 - 69 mg / dL. Glucose values were lower during all three periods than previous values recorded for cultured or captive red drum studies. This may indicate that fish from this population were under less stress than other populations previously sampled.

  19. Specialist bees collect Asteraceae pollen by distinctive abdominal drumming (Osmia) or brushing (Melissodes, Svastra)

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Four species of western US Osmia (Cephalosmia) bees that are Asteraceae specialists (oligoleges) were observed to employ a heretofore unappreciated, stereotypical means of collecting pollen, abdominal drumming, to gather pollen from 19 flowering species representing nine tribes of Asteraceae. Abdom...

  20. Characterization of waste drums using nonintrusive active and passive computed tomography

    SciTech Connect

    Roberson, G.P.; Martz, H.E.; Decman, D.J.; Camp, D.C.; Azevedo, S.G.; Keto, E.R.

    1994-08-01

    We have developed a data acquisition scanner for gamma-ray nondestructive assay (NDA) active and passive computed tomography (A&PCT) along with associated computational techniques for image reconstruction, analysis, and display. We are using this scanner to acquire data sets of mock-waste drums at Lawrence Livermore National Laboratory (LLNIL). In this paper, we discuss some issues associated with gamma-ray spectroscopy assay, NDA imaging, describe the design and construction of an NDA drum scanner and report on code development for image reconstruction. We also present representative A&PCT assay results of well characterized mock-waste drums. These preliminary results suggest that A&PCT imaging can be used to produce accurate absolute assays of radioactivity in real-waste drums.

  1. Identification of the fast and thermal neutron characteristics of transuranic waste drums

    SciTech Connect

    Storm, B.H. Jr.; Bramblett, R.L.; Hensley, C.

    1997-11-01

    Fissile and spontaneously fissioning material in transuranic waste drums can be most sensitively assayed using an active and passive neutron assay system such as the Active Passive Neutron Examination and Assay. Both the active and the passive assays are distorted by the presence of the waste matrix and containerization. For accurate assaying, this distortion must be characterized and accounted for. An External Matrix Probe technique has been developed that accomplishes this task. Correlations between in-drum neutron flux measurements and monitors in the Active Passive Neutron Examination and Assay chamber with various matrix materials provide a non-invasive means of predicting the thermal neutron flux in waste drums. Similarly, measures of the transmission of fast neutrons emitted from sources in the drum. Results obtained using the Lockheed Martin Specialty Components Active Passive Neutron Examination and Assay system are discussed. 12 figs., 1 tab.

  2. Compulsive Drumming Induced by Dopamine Agonists in Parkinson’s Disease: Another Aspect of Punding

    PubMed Central

    Vitale, Carmine; Trojano, Luigi; Barone, Paolo; Errico, Domenico; Agosti, Valeria; Sorrentino, Giuseppe; Grossi, Dario; Santangelo, Gabriella

    2013-01-01

    We report the case of a man affected by Parkinson’s disease who developed an unusual, severe, repetitive behavior characterized by an irrepressible need to drum and beat percussion instruments following to the introduction of pramipexole. This compulsive behavior was not associated to a pattern of chronic inappropriate overuse of dopaminergic medication or other psychiatric symptoms. Sharing many features with other repetitive behaviors, compulsive drumming might be considered a distinct manifestation of punding in Parkinson’s disease. PMID:23242361

  3. Mercury concentrations in red drum, Sciaenops ocellatus, from estuarine and offshore waters of Florida.

    PubMed

    Adams, Douglas H; Onorato, Gregory V

    2005-03-01

    Dorsal muscle tissue from 712 red drum, Sciaenops ocellatus, from Florida waters were analyzed for total mercury content. Mercury levels detected in these red drum varied but in most study areas were usually lower than regulatory threshold guidelines. Total mercury levels in individual fish from all study areas ranged from 0.020 to 3.6 ppm (wet weight). Total mercury levels detected in red drum from the Florida Keys-Florida Bay area were often higher than those in fish from all other estuarine study areas. Positive relationships between total mercury levels and fish size (length and weight) and fish age were observed in most Florida study areas, indicating that mercury levels tend to increase over time as red drum grow. The majority of large, mature red drum examined contained mercury levels greater than the 0.5-ppm threshold level set by the Florida Department of Health (DOH). Approximately 94% of all adult red drum from offshore waters adjacent to Tampa Bay contained mercury levels greater than or equal to the 0.5-ppm threshold level, and 64% contained levels greater than or equal to the DOH 1.5-ppm "no consumption" level. All fish from this area with mercury levels greater than 1.5 ppm were large individuals (670 mm SL). Eight percent of legal-size red drum from Florida waters contained total mercury levels greater than or equal to the 0.5-ppm threshold level. The majority (52%) of these legal-size fish greater than or equal to 0.5 ppm were from the Florida Keys-Florida Bay area. In the Florida recreational fishery, the current maximum size limit for this species is an effective filter that prevents humans from consuming those red drum with the greatest likelihood of containing high mercury levels.

  4. Predation of the zebra mussel (Dreissena polymorpha) by freshwater drum in western Lake Erie

    USGS Publications Warehouse

    French, John R. P.; Bur, Michael T.; Nalepa, Thomas F.; Schloesser, Donald W.

    1992-01-01

    Environmental and economic problems associated with the colonization of zebra mussels (Dreissena polymorpha) in western Lake Erie created a need to investigate control mechanisms. Predation by fishes is one potential means of control, but predation on zebra mussels by native fishes in Lake Erie is unknown. The freshwater drum (Aplodinotus grunniens) is the most likely fish predator since it is the only fish with pharyngeal teeth capable of crushing mollusk shells. In 1990, freshwater drum were collected in western Lake Erie from 9 sites near rocky reefs and 13 sites with silt or sand bottoms, and gut contents were examined. Predation on zebra mussels increased as drum size increased. Small drum (200-249 mm in length) fed mainly on dipterans, amphipods, and small fish; small zebra mussels (375 mm in length) fed almost exclusively on zebra mussels (seasons and locations combined). The smallest drum capable of crushing zebra mussel shells was 265 mm. Since freshwater drum over 375 mm feed heavily on zebra mussels, they may become a possible biological control mechanism for mussels in portions of North America.

  5. Reconstruction of the isotope activity content of heterogeneous nuclear waste drums.

    PubMed

    Krings, Thomas; Mauerhofer, Eric

    2012-07-01

    Radioactive waste must be characterized in order to verify its conformance with national regulations for intermediate storage or its disposal. Segmented gamma scanning (SGS) is a most widely applied non-destructive analytical technique for the characterization of radioactive waste drums. The isotope specific activity content is generally calculated assuming a homogeneous matrix and activity distribution for each measured drum segment. However, real radioactive waste drums exhibit non-uniform isotope and density distributions most affecting the reliability and accuracy of activities reconstruction in SGS. The presence of internal shielding structures in the waste drum contributes generally to a strong underestimation of the activity and this in particular for radioactive sources emitting low energy gamma-rays independently of their spatial distribution. In this work we present an improved method to quantify the activity of spatially concentrated gamma-emitting isotopes (point sources or hot spots) in heterogeneous waste drums with internal shielding structures. The isotope activity is reconstructed by numerical simulations and fits of the angular dependent count rate distribution recorded during the drum rotation in SGS using an analytical expression derived from a geometric model. First results of the improved method and enhancements of this method are shown and are compared to each other as well as to the conventional method which assumes a homogeneous matrix and activity distribution. It is shown that the new model improves the accuracy and the reliability of the activity reconstruction in SGS and that the presented algorithm is suitable with respect to the framework requirement of industrial application.

  6. Rotary drum composting of different organic waste mixtures.

    PubMed

    Kalamdhad, Ajay S; Kazmi, Absar A

    2009-03-01

    The effects of three different mixtures of organic waste on composting in a rotary drum were examined by measuring changes in physico-chemical and biological parameters. It was observed that the time courses of the three mixtures: run A (grass cuttings, vegetable waste and food waste), run B (cattle manure, vegetable waste and sawdust) and run C (cattle manure, food waste, vegetable waste, paper waste and sawdust) were quite diverse. Run B, with initial C/N ratio 22 and containing a large proportion of cattle manure produced high quality and mature compost within 20 days. It showed a final total nitrogen (2.1%), final total phosphorus 3.52 g kg(-1), final total organic carbon (TOC) (24.8%) and final moisture content (44%). At the end of 20 days, higher degradation led to final chemical oxygen demand (COD) (454 mg L(- 1)), biochemical oxygen demand (BOD) (107 mg L(- 1)), fecal coliform (1.2 x 10(2) bacteria g(- 1)), fecal streptococci (85 bacteria g(-1)) and low electrical conductivity (1.658 dS m(-1)), respectively. Furthermore, run C with initial C/N ratio of 30 and containing a larger amount of food and vegetable waste produced good quality compost and resulted in 4.34% total nitrogen and 2.42% total phosphorus after 20 days, but, it had higher final fecal coliform 2.5 x 10(4) bacteria g( -1), fecal streptococci 2.1 x 10(4) bacteria g(-1), high TOC and NH(4)-N and a BOD/COD ratio of 0.63, which rendered it hygienically unsafe and immature. Finally, run A with initial C/N ratio of 15 showed a higher amount of EC (4.84 dS m(-1)), NH(4)-N, BOD/COD ratio of 0.4 with 15% nitrogen loss, which indicated an unstable product even after 20 days of composting. Therefore, it was found that rotary drum composting of a combination of cattle manure, vegetable waste and sawdust resulted in a primary stabilized compost within 20 days of composting.

  7. Evaluation of an Innovative Sand Filter for Small System Drinking Water Treatment

    EPA Science Inventory

    Results of evaluation of an innovative sand filter that uses the concepts of both slow and rapid sand filtration are presented in this article. The system uses a low-cost “Drum Sand Filter” (DSF) that consists of a 55-gallon drum filled with layers of sand of varying size. A low-...

  8. Computed tomography of human joints and radioactive waste drums

    SciTech Connect

    Martz, Harry E.; Roberson, G. Patrick; Hollerbach, Karin; Logan, Clinton M.; Ashby, Elaine; Bernardi, Richard

    1999-12-02

    X- and gamma-ray imaging techniques in nondestructive evaluation (NDE) and assay (NDA) have seen increasing use in an array of industrial, environmental, military, and medical applications. Much of this growth in recent years is attributed to the rapid development of computed tomography (CT) and the use of NDE throughout the life-cycle of a product. Two diverse examples of CT are discussed, 1.) Our computational approach to normal joint kinematics and prosthetic joint analysis offers an opportunity to evaluate and improve prosthetic human joint replacements before they are manufactured or surgically implanted. Computed tomography data from scanned joints are segmented, resulting in the identification of bone and other tissues of interest, with emphasis on the articular surfaces. 2.) We are developing NDE and NDA techniques to analyze closed waste drums accurately and quantitatively. Active and passive computed tomography (A and PCT) is a comprehensive and accurate gamma-ray NDA method that can identify all detectable radioisotopes present in a container and measure their radioactivity.

  9. Limitation of tritium outgassing from tritiated solid waste drums

    SciTech Connect

    Liger, K.; Trabuc, P.; Lefebvre, X.; Troulay, M.; Perrais, C.

    2015-03-15

    In the framework of the development of fusion thermonuclear reactors, tritiated solid waste is foreseen and will have to be managed. The management of tritiated waste implies limitations in terms of activity and tritium degassing. The degassing tritium can be under the form of tritiated hydrogen, tritiated water and, in some specific cases, negligible amount of tritiated volatile organic compound. Hence, considering the major forms of degassing tritium, CEA has developed a mixed-compound dedicated to tritium trapping in drums. Based on several experiments, the foreseen mixed compound is composed of MnO{sub 2}, Ag{sub 2}O, Pt and molecular sieve, the three first species having the ability to convert tritiated hydrogen into tritiated water and the last one acting as a trap for tritiated water. To assess the performance of the trapping mixture, experimental tests were performed at room temperature on tritiated dust composed of beryllium and carbon. It was shown that the metallic oxides mixture used for tritiated hydrogen conversion is efficient and that tritiated water adsorption was limited due to an inefficient regeneration of the molecular sieve prior to its use. Apart from this point, the tritium release from waste was reduced by a factor of 5.5, which can be improved up to 87 if the adsorption step is efficient.

  10. Computed tomography of human joints and radioactive waste drums

    SciTech Connect

    Ashby, E; Bernardi, R; Hollerbach, K; Logan, C; Martz, H; Roberson, G P

    1999-06-01

    X- and gamma-ray imaging techniques in nondestructive evaluation (NDE) and assay (NDA) have been increasing use in an array of industrial, environmental, military, and medical applications. Much of this growth in recent years is attributed to the rapid development of computed tomography (CT) and the use of NDE throughout the life-cycle of a product. Two diverse examples of CT are discussed. (1) The computational approach to normal joint kinematics and prosthetic joint analysis offers an opportunity to evaluate and improve prosthetic human joint replacements before they are manufactured or surgically implanted. Computed tomography data from scanned joints are segmented, resulting in the identification of bone and other tissues of interest, with emphasis on the articular surfaces. (2) They are developing NDE and NDE techniques to analyze closed waste drums accurately and quantitatively. Active and passive computed tomography (A and PCT) is a comprehensive and accurate gamma-ray NDA method that can identify all detectable radioisotopes present in a container and measure their radioactivity.

  11. Species Profiles. Life Histories and Environmental Requirements of Coastal Fishes and Invertebrates (Gulf of Mexico). RED DRUM.

    DTIC Science & Technology

    1985-06-01

    RANGE MORPHOLOGY/IDENTIFICATION AIDS Scientific name ............ Sciaenops The red drum has 11 spines on the ocellatus (Linnaeus) dorsal fin (the 11th...34 prepared to assist in environmental impact assessment. The red drum ( Sciaenops k- .. ocellatus ) is an estuarine dependent species. It spends its...oescriptors Estuaries Growth Fishes Feeding .. Idetrf..rs/Ole. .Ended Tamn-, Red drum Habitat requirements Sciaenops ocellatus Spawning Temperature

  12. Method for producing H.sub.2 using a rotating drum reactor with a pulse jet heat source

    DOEpatents

    Paulson, Leland E.

    1990-01-01

    A method of producing hydrogen by an endothermic steam-carbon reaction using a rotating drum reactor and a pulse jet combustor. The pulse jet combustor uses coal dust as a fuel to provide reaction temperatures of 1300.degree. to 1400.degree. F. Low-rank coal, water, limestone and catalyst are fed into the drum reactor where they are heated, tumbled and reacted. Part of the reaction product from the rotating drum reactor is hydrogen which can be utilized in suitable devices.

  13. Source Test Report for the 205 Delayed Coking Unit Drum 205-1201 and Drum 205-1202 Depressurization Vents (Marathon Petroleum Company LLC)

    EPA Pesticide Factsheets

    The 2010 Source Test was performed during the atmospheric depressurization step of the delayed coking process prior to the removal of petroleum coke from the coke drum. The 205 DCU was operated under a variety of conditions during the 2010 Source Test.

  14. Utilizing Drumming for American Indians/Alaska Natives with Substance Use Disorders: A Focus Group Study

    PubMed Central

    Dickerson, Daniel; Robichaud, Francis; Teruya, Cheryl; Nagaran, Kathleen; Hser, Yih-Ing

    2013-01-01

    Background Drumming has been utilized among American Indian/Alaska Native (AI/AN) tribes for centuries to promote healing and self-expression. Drum-Assisted Recovery Therapy for Native Americans (DARTNA), currently under development, is a substance abuse treatment utilizing drumming as a core component. Objectives Focus groups were conducted to assist in the development of the DARTNA protocol. Feedback obtained from these focus groups will inform a subsequent pretest of DARTNA and an empirical study analyzing its effectiveness. Methods Three focus groups were conducted among AIs/ANs with substance use disorders (n = 6), substance abuse treatment providers (n = 8), and a community advisory board (n = 4) to solicit feedback prior to a pretest of the DARTNA protocol. Results Overall, participants indicated that DARTNA could be beneficial for AIs/ANs with substance use disorders. Four overarching conceptual themes emerged across the focus groups: (1) benefits of drumming, (2) importance of a culture-based focus, (3) addressing gender roles in drumming activities, and (4) providing a foundation of common AI/AN traditions. Conclusions The DARTNA protocol is a potentially beneficial and culturally appropriate substance abuse treatment strategy for AIs/ANs. In order to optimize the potential benefits of a substance abuse treatment protocol utilizing drumming for AIs/ANs, adequate attention to tribal diversity and gender roles is needed. Scientific Significance Due to the shortage of substance abuse treatments utilizing traditional healing activities for AIs/ANs, including drumming, results from this study provide an opportunity to develop an intervention that may meet the unique treatment needs of AIs/ANs. PMID:22931086

  15. Dietary arginine requirement of juvenile red drum (Sciaenops ocellatus) based on weight gain and feed efficiency.

    PubMed

    Barziza, D E; Buentello, J A; Gatlin, D M

    2000-07-01

    Increasing aquacultural production of red drum (Sciaenops ocellatus) has prompted the determination of many of this species' nutritional requirements. However, limited information is available concerning its amino acid requirements, especially for arginine. Therefore, a feeding trial was conducted with juvenile red drum to determine their quantitative dietary requirement for arginine. Experimental diets contained 35 g crude protein/100 g from red drum muscle and crystalline amino acids. Incremental levels of arginine were added to the diets in place of a mixture of glycine and aspartic acid to maintain all diets isonitrogenous. All diets were fed in triplicate to juvenile red drum for 7 wk. Graded levels of arginine significantly (P < 0.05) affected weight gain, feed efficiency, protein efficiency ratio (PER) and plasma arginine levels of the fish. Based on least-squares regression of feed efficiency and PER data, the minimum requirement (+/- SEM) of red drum for arginine was estimated at 1.44 (+/- 0.15) and 1.48 (+/- 0.12) g/100 g diet (4.11 and 4.23 g/100 g dietary protein), respectively. The arginine requirements estimated from weight gain data were 1.75 (+/- 0.18) g/100 g diet or 5.0 g/100 g dietary protein. These values are similar to those reported for other carnivorous fish species.

  16. A computer model of gas generation and transport within TRU waste drums

    SciTech Connect

    Smith, F.G. III

    1988-06-01

    A computer model has been developed to predict radiolytic gas generation and transport within Transuranic (TRU) waste drums and surrounding enclosures. Gas generation from the radiolytic decomposition of organic material contaminated with plutonium is modeled and the concentrations of gas throughout the waste drum and enclosures are determined using a diffusional transport model. The model accurately reproduces experimentally measured gas concentrations. With polyethylene waste in unvented drums, the model predicts that the concentration of hydrogen gas can exceed 4 mole percent (lower flammable limit) with only about 5 curies of plutonium. If the drum liner is punctured and an unrestricted 0.75-in. carbon composite filter vent is installed in the drum lid, the plutonium loading can be increased to 240 Ci without generating flammable gas mixtures. Larger diameter filters can be used to increase the curie loading. The model has been used to show that shipments of 1000 Ci of plutonium-238 contaminated waste from Savannah River to the WIPP site are feasible using the TRUPACT shipping container. 10 refs., 17 figs., 6 tabs.

  17. Numerical Studies on Time-Varying Stiffness of Disk-Drum Type Rotor with Bolt Loosening

    NASA Astrophysics Data System (ADS)

    Qin, Zhaoye; Chu, Fulei

    2015-07-01

    Disk-drum type rotors are widely used in industry for their high stiffness and low weight properties. In disk-drum type rotors, the adjacent disks and drums are commonly connected by bolted joints. Those rotating joint interfaces are subjected to numerous combinations of loads during normal operation, where loosening of the connecting bolts might occur. The bolt loosening will change the local stiffness of the rotor, which in turn affect the rotor dynamics and even result in structural failures. In this paper, the local stiffness of a disk- drum rotor with bolt loosening is investigated numerically. A three-dimensional (3D) finite element (FE) model for the bolted disk-drum joint is established in ANSYS, where the bolt loosening is simulated by reducing the preloads of certain bolts, and removing those bolts as the limiting case. Simulations are performed on the FE model to evaluate the joint behaviour under static loads. Periodic variations of the joint deflections with respect to the rotation angle of the shaft are obtained, which implies the appearance of the time-varying local stiffness in the rotor system. The studies in this paper help accurate prediction of the rotor dynamics and early detection of bolt loosening.

  18. Nuclear waste calorimeter for very large drums with 385 litres sample volume

    SciTech Connect

    Jossens, G.; Mathonat, C.; Bachelet, F.

    2015-03-15

    Calorimetry is a very precise and well adapted tool for the classification of drums containing nuclear waste material depending on their level of activities (low, medium, high). A new calorimeter has been developed by SETARAM Instrumentation and the CEA Valduc in France. This new calorimeter is designed for drums having a volume bigger than 100 liters. It guarantees high operator safety by optimizing drum handling and air circulation for cooling, and optimized software for direct measurement of the quantity of nuclear material. The LVC1380 calorimeter makes it possible to work over the range 10 to 3000 mW, which corresponds to approximately 0.03 to 10 g of tritium or 3 to 955 g of {sup 241}Pu in a volume up to 385 liters. This calorimeter is based on the heat flow measurement using Peltier elements which surround the drum in the 3 dimensions and therefore measure all the heat coming from the radioactive stuff whatever its position inside the drum. Calorimeter's insulating layers constitute a thermal barrier designed to filter disturbances until they represent less than 0.001 Celsius degrees and to eliminate long term disturbances associated, for example, with laboratory temperature variations between day and night. A calibration device based on Joule effect has also been designed. Measurement time has been optimized but remains long compared with other methods of measurement such as gamma spectrometry but its main asset is to have a good accuracy for low level activities.

  19. Hazards Associated with Legacy Nitrate Salt Waste Drums Managed under the Container Isolation Plan

    SciTech Connect

    Funk, David John; Clark, David Lewis

    2015-01-07

    At present, there are 29 drums of nitrate waste salts (oxidizers with potentially acidic liquid bearing RCRA characteristics D001 and D002) that are awaiting processing, specifically to eliminate these characteristics and to allow for ultimate disposition at WIPP. As a result of the Feb. 14th, 2014 drum breach at WIPP, and the subsequent identification of the breached drum as a product ofLANL TRU waste disposition on May 15th, 2014, these 29 containers were moved into the Perrnacon in Dome 231 at TA-54 Area G, as part of the New Mexico Environment Department (NMED) approved container isolation plan. The plan is designed to mitigate hazards associated with the nitrate salt bearing waste stream. The purpose of this document is to articulate the hazards associated with un-remediated nitrate salts while in storage at LANL. These hazards are distinctly different from the Swheat-remediated nitrate salt bearing drums, and this document is intended to support the request to remove the un-remediated drums from management under the container isolation plan. Plans to remediate and/or treat both of these waste types are being developed separately, and are beyond the scope of this document.

  20. Ringlike spin segregation of binary mixtures in a high-velocity rotating drum

    NASA Astrophysics Data System (ADS)

    Decai, Huang; Ming, Lu; Gang, Sun; Yaodong, Feng; Min, Sun; Haiping, Wu; Kaiming, Deng

    2012-03-01

    This study presents molecular dynamics simulations on the segregation of binary mixtures in a high-velocity rotating drum. Depending on the ratio between the particle radius and density, similarities to the Brazil-nut effect and its reverse form are shown in the ringlike spin segregation patterns in radial direction. The smaller and heavier particles accumulated toward the drum wall, whereas the bigger and lighter particles accumulated toward the drum center. The effects of particle radius and density on the segregation states were quantified and the phase diagram of segregation in the ρb/ρs - rb/rs space was plotted. The observed phenomena can be explained by the combined percolation and the buoyancy effects.

  1. Lanthanide nano-drums: a new class of molecular nanoparticles for potential biomedical applications.

    PubMed

    Jones, Richard A; Gnanam, Annie J; Arambula, Jonathan F; Jones, Jessica N; Swaminathan, Jagannath; Yang, Xiaoping; Schipper, Desmond; Hall, Justin W; DePue, Lauren J; Dieye, Yakhya; Vadivelu, Jamuna; Chandler, Don J; Marcotte, Edward M; Sessler, Jonathan L; Ehrlich, Lauren I R; Brown, Katherine A

    2014-01-01

    We are developing a new class of lanthanide-based self-assembling molecular nanoparticles as potential reporter molecules for imaging, and as multi-functional nanoprobes or nanosensors in diagnostic systems. These lanthanide "nano-drums" are homogeneous 4d-4f clusters approximately 25 to 30 Å in diameter that can emit from the visible to near-infrared (NIR) wavelengths. Here, we present syntheses, crystal structures, photophysical properties, and comparative cytotoxicity data for six nano-drums containing either Eu, Tb, Lu, Er, Yb or Ho. Imaging capabilities of these nano-drums are demonstrated using epifluorescence, total internal reflection fluorescence (TIRF), and two-photon microscopy. We discuss how these molecular nanoparticles can to be adapted for a range of assays, particularly by taking advantage of functionalization strategies with chemical moieties to enable conjugation to protein or nucleic acids.

  2. Measurement of VOC permeability of polymer bags and VOC solubility in polyethylene drum liner

    SciTech Connect

    Liekhus, K.J.; Peterson, E.S.

    1995-03-01

    A test program conducted at the Idaho National Engineering Laboratory (INEL) investigated the use of a transport model to estimate the volatile organic compound (VOC) concentration in the void volume of a waste drum. Unsteady-state VOC transport model equations account for VOC permeation of polymer bags, VOC diffusion across openings in layers of confinement, and VOC solubility in a polyethylene drum liner. In support of this program, the VOC permeability of polymer bags and VOC equilibrium concentration in a polyethylene drum liner were measured for nine VOCs. The VOCs used in experiments were dichloromethane, carbon tetrachloride, cyclohexane, toluene, 1,1,1-trichloroethane, methanol, 1,1,2-trichloro-1,2,2-trifluoroethane (Freon-113), trichloroethylene, and p-xylene. The experimental results of these measurements as well as a method of estimating both parameters in the absence of experimental data are described in this report.

  3. Drumming as a Medium to Promote Emotional and Social Functioning of Children in Middle Childhood in Residential Care

    ERIC Educational Resources Information Center

    Flores, Kim; van Niekerk, Caroline; le Roux, Liana

    2016-01-01

    This study explores the potential of drumming to enhance emotional and social functioning of children in residential care. Fifteen children (aged 7-12) from a child and youth care centre in South Africa attended four months of weekly drumming sessions. Gestalt theory principles informed the workshops' theoretical foundation and interpretation of…

  4. An ABC of Drumming: Children's Narratives about Beat, Rhythm and Groove in a Primary Classroom

    ERIC Educational Resources Information Center

    Mackinlay, Elizabeth

    2014-01-01

    In this paper, I use a bricolage of arts-based research and writing practices to explore narratives by Grade 4 children about their experiences in a drumming circle called "Bam Bam" as represented in a text they created with me called An ABC of drumming. The term "narrative" is used here in a contemporary sense to…

  5. Hazardous Waste Characterization Survey of Unknown Drums at the 21st Tactical Fighter Wing, Elmendorf and Shemya Air Force Bases, and Galena and King Salmon Airports, Alaska

    DTIC Science & Technology

    1991-12-01

    identified by the base bioenvironmental engineer. 2 DISCUSSION Method The field work consisted of two tasks: screening all drums for waste oil and sampling...drums. At Elmendorf AFB the waste oil drums were marked to be processed through a recycle program by an Armstrong Laboratory contractor. For Shemya, the...constant Artic winds. At Galena the drums were physically moved to an adjacent waste oil storage area for use as fuel in waste oil burners being

  6. Short-term physiological responses of wild and hatchery-produced red drum during angling

    USGS Publications Warehouse

    Gallman, E.A.; Isely, J.J.; Tomasso, J.R.; Smith, T.I.J.

    1999-01-01

    Serum cortisol concentrations, plasma glucose concentrations, plasma lactate concentrations, and plasma osmolalities increased in red drum Sciaenops ocellatus (26.0-65.5 cm total length) during angling in estuarine waters (17-33 g/L salinity, 21-31??C). Angling time varied from as fast as possible (10 s) to the point when fish ceased resisting (up to 350 s). The increases in the physiological characteristics were similar in wild and hatchery-produced fish. This study indicates that hatchery-produced red drum may be used in catch-and-release studies to simulate the responses of wild fish.

  7. Analysis of a boron-carbide-drum-controlled critical reactor experiment

    NASA Technical Reports Server (NTRS)

    Mayo, W. T.

    1972-01-01

    In order to validate methods and cross sections used in the neutronic design of compact fast-spectrum reactors for generating electric power in space, an analysis of a boron-carbide-drum-controlled critical reactor was made. For this reactor the transport analysis gave generally satisfactory results. The calculated multiplication factor for the most detailed calculation was only 0.7-percent Delta k too high. Calculated reactivity worth of the control drums was $11.61 compared to measurements of $11.58 by the inverse kinetics methods and $11.98 by the inverse counting method. Calculated radial and axial power distributions were in good agreement with experiment.

  8. Natural mortality rates of freshwater drum larvae in the Missouri River

    SciTech Connect

    Cada, G.F.; Hergenrader, G.L.

    1980-09-01

    Instantaneous total mortality rates for planktonic larval freshwater drums (Aplodinotus grunniens) in a channelized stretch of the Missouri River were estimated from analyses of cumulative catch curves. Mortality rates, which ranged from 0.11 to 0.21 per day, were significantly greater in 1976 than in 1974. Basing our interpretation on the underrepresentation of eggs and early larvae in the channelized river samples, we hypothesize that favorable environments upstream represent a more significant source of recruitment of larvae to the freshwater drum population than the channelized river.

  9. Synchronized drumming enhances activity in the caudate and facilitates prosocial commitment--if the rhythm comes easily.

    PubMed

    Kokal, Idil; Engel, Annerose; Kirschner, Sebastian; Keysers, Christian

    2011-01-01

    Why does chanting, drumming or dancing together make people feel united? Here we investigate the neural mechanisms underlying interpersonal synchrony and its subsequent effects on prosocial behavior among synchronized individuals. We hypothesized that areas of the brain associated with the processing of reward would be active when individuals experience synchrony during drumming, and that these reward signals would increase prosocial behavior toward this synchronous drum partner. 18 female non-musicians were scanned with functional magnetic resonance imaging while they drummed a rhythm, in alternating blocks, with two different experimenters: one drumming in-synchrony and the other out-of-synchrony relative to the participant. In the last scanning part, which served as the experimental manipulation for the following prosocial behavioral test, one of the experimenters drummed with one half of the participants in-synchrony and with the other out-of-synchrony. After scanning, this experimenter "accidentally" dropped eight pencils, and the number of pencils collected by the participants was used as a measure of prosocial commitment. Results revealed that participants who mastered the novel rhythm easily before scanning showed increased activity in the caudate during synchronous drumming. The same area also responded to monetary reward in a localizer task with the same participants. The activity in the caudate during experiencing synchronous drumming also predicted the number of pencils the participants later collected to help the synchronous experimenter of the manipulation run. In addition, participants collected more pencils to help the experimenter when she had drummed in-synchrony than out-of-synchrony during the manipulation run. By showing an overlap in activated areas during synchronized drumming and monetary reward, our findings suggest that interpersonal synchrony is related to the brain's reward system.

  10. Russian Containers for Transportation of Solid Radioactive Waste

    SciTech Connect

    Petrushenko, V. G.; Baal, E. P.; Tsvetkov, D. Y.; Korb, V. R.; Nikitin, V. S.; Mikheev, A. A.; Griffith, A.; Schwab, P.; Nazarian, A.

    2002-02-28

    The Russian Shipyard ''Zvyozdochka'' has designed a new container for transportation and storage of solid radioactive wastes. The PST1A-6 container is cylindrical shaped and it can hold seven standard 200-liter (55-gallon) drums. The steel wall thickness is 6 mm, which is much greater than standard U.S. containers. These containers are fully certified to the Russian GOST requirements, which are basically identical to U.S. and IAEA standards for Type A containers. They can be transported by truck, rail, barge, ship, or aircraft and they can be stacked in 6 layers in storage facilities. The first user of the PST1A-6 containers is the Northern Fleet of the Russian Navy, under a program sponsored jointly by the U.S. DoD and DOE. This paper will describe the container design and show how the first 400 containers were fabricated and certified.

  11. Structural Acoustic UXO Detection and Identification in Marine Environments - Interim Report for SERDP MR-2103 Follow-On

    DTIC Science & Technology

    2015-07-30

    seven include the rock (T2), the 55 gallon water filled drum (T3), the 5:1 aspect telephone pole section (T5), the panel (T10 or CP), the 2:1 aspect...telephone pole section (T15), the cement block (T18), and the tire (T19). The proud and buried targets in the target field are listed and labelled in...N1 5inch Rocket nose-up 60o T2 Rock T15 2:1 Aspect Phone Pole Section N2 5inch Rocket nose-up 30o T3 55 Gallon Filled Drum T17 2 ft Aluminum Cylinder

  12. The Extraordinary Nature of Barney's Drumming: A Complementary Study of Ordinary Noise Making in Chimpanzees

    PubMed Central

    Dufour, Valérie; Pasquaretta, Cristian; Gayet, Pierre; Sterck, Elisabeth H. M.

    2017-01-01

    In a previous study (Dufour et al., 2015) we reported the unusual characteristics of the drumming performance of a chimpanzee named Barney. His sound production, several sequences of repeated drumming on an up-turned plastic barrel, shared features typical for human musical drumming: it was rhythmical, decontextualized, and well controlled by the chimpanzee. This type of performance raises questions about the origins of our musicality. Here we recorded spontaneously occurring events of sound production with objects in Barney's colony. First we collected data on the duration of sound making. Here we examined whether (i) the context in which objects were used for sound production, (ii) the sex of the producer, (iii) the medium, and (iv) the technique used for sound production had any effect on the duration of sound making. Interestingly, duration of drumming differed across contexts, sex, and techniques. Then we filmed as many events as possible to increase our chances of recording sequences that would be musically similar to Barney's performance in the original study. We filmed several long productions that were rhythmically interesting. However, none fully met the criteria of musical sound production, as previously reported for Barney. PMID:28154521

  13. 49 CFR 393.47 - Brake actuators, slack adjusters, linings/pads and drums/rotors.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 5 2010-10-01 2010-10-01 false Brake actuators, slack adjusters, linings/pads and..., slack adjusters, linings/pads and drums/rotors. (a) General requirements. Brake components must be... be the same. (d) Linings and pads. The thickness of the brake linings or pads shall meet...

  14. 77 FR 47840 - American Drum and Pallet Company Site; Memphis, Shelby County, Tennessee; Notice of settlement

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-10

    ... the settlement are available from Ms. Paula V. Painter. Submit your comments by Site name American... AGENCY American Drum and Pallet Company Site; Memphis, Shelby County, Tennessee; Notice of settlement... Company Superfund Site located in Memphis, Shelby County, Tennessee. DATES: The Agency will...

  15. PCR primer pairs for 100 microsatellites in red drum (Sciaenops ocellatus)

    Technology Transfer Automated Retrieval System (TEKTRAN)

    One hundred nuclear-encoded microsatellites from a genomic DNA library of red drum (Sciaenops ocellatus) were isolated and characterized. Eight of the microsatellites had tetra-nucleotide motifs, while 92 had di-nucleotide motifs. The average number of alleles at the 100 microsatellites among a sa...

  16. Process and formulation effects on solar thermal drum dried prune pomace

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The processing of dried plums into prune juice and concentrate yields prune pomace as a coproduct; the pomace could potentially be utilized as a food ingredient but requires stabilization for long-term storage. Drum drying is one method that could be used to dry and stabilize prune pomace, and a dru...

  17. Drums and Poems: An Intervention Promoting Empathic Connection and Literacy in Children

    ERIC Educational Resources Information Center

    Sassen, Georgia

    2012-01-01

    Expressive therapies can be used with groups of children to increase empathy and reduce bullying and violence. When educators feel pressured to focus on standardized tests and basic skills, there is little attention and time for such programs. Drums and Poems is an intervention that counselors and teachers can use to address these problems by…

  18. The Extraordinary Nature of Barney's Drumming: A Complementary Study of Ordinary Noise Making in Chimpanzees.

    PubMed

    Dufour, Valérie; Pasquaretta, Cristian; Gayet, Pierre; Sterck, Elisabeth H M

    2017-01-01

    In a previous study (Dufour et al., 2015) we reported the unusual characteristics of the drumming performance of a chimpanzee named Barney. His sound production, several sequences of repeated drumming on an up-turned plastic barrel, shared features typical for human musical drumming: it was rhythmical, decontextualized, and well controlled by the chimpanzee. This type of performance raises questions about the origins of our musicality. Here we recorded spontaneously occurring events of sound production with objects in Barney's colony. First we collected data on the duration of sound making. Here we examined whether (i) the context in which objects were used for sound production, (ii) the sex of the producer, (iii) the medium, and (iv) the technique used for sound production had any effect on the duration of sound making. Interestingly, duration of drumming differed across contexts, sex, and techniques. Then we filmed as many events as possible to increase our chances of recording sequences that would be musically similar to Barney's performance in the original study. We filmed several long productions that were rhythmically interesting. However, none fully met the criteria of musical sound production, as previously reported for Barney.

  19. Low-head recirculating aquaculture system for juvenile red drum production

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The USDA Agricultural Research Service and the Center for Aquaculture and Stock Enhancement at Harbor Branch Oceanographic Institute-FAU (HBOI-FAU) are collaborating to evaluate low-head recirculating aquaculture system designs to intensively produce red drum juveniles as part of the Florida Fish an...

  20. Dyadic Drumming across the Lifespan Reveals a Zone of Proximal Development in Children

    ERIC Educational Resources Information Center

    Kleinspehn-Ammerlahn, Anna; Riediger, Michaela; Schmiedek, Florian; von Oertzen, Timo; Li, Shu-Chen; Lindenberger, Ulman

    2011-01-01

    Many social interactions require the synchronization--be it automatically or intentionally--of one's own behavior with that of others. Using a dyadic drumming paradigm, the authors delineate lifespan differences in interpersonal action synchronization (IAS). Younger children, older children, younger adults, and older adults in same- and mixed-age…

  1. DEVELOPMENT AND TESTING OF THE BLANTON CLAMSHELL CLOSUREFOR USE ON RADIOACTIVE MATERIAL PACKAGING DRUMS

    SciTech Connect

    Blanton, P

    2007-10-18

    This paper provides a brief history of the U.S. Type B 6M specification container, its introduction into U.S. Code of federal regulations and its scheduled elimination three decades later. The paper also presents development, testing and deployment by the Department of Energy (DOE) of an enhanced drum closure called the 'Blanton Clamshell' (patent pending) that was designed to replace the standard open-head C-ring closure for the 55- and 85-gallon drums described in the 6M specification to extend their safe use. Nuclear Filter Technology has the Exclusive License for Clamshell production. Drum packages utilizing the standard C-ring closure have been a main-stay for over a half of a century in the national and international nuclear industry for shipping radioactive materials and will remain so in the foreseeable future. Drum package use in the U.S. increased heavily in the 1950's with development of the Weapons Complex and subsequently the commercial nuclear reactor industry.

  2. A UK comparison for measurements of low levels of gamma-emitters in waste drums.

    PubMed

    Dean, Julian

    2009-05-01

    Much of the work of the UK nuclear industry is now concerned with decommissioning many of the existing power stations and other facilities. An important aspect of this work is the accurate measurement of low levels of radioactivity in waste forms such as building materials in order that these materials can be assigned to the correct waste streams. This has led to a call for suitable standards and reference materials, and the specific needs of UK users were identified at an NPL workshop in 2005. One of the highest priorities was for 'soft waste' spiked with gamma-emitters in a 200 L drum format, with an activity concentration of just under 0.4 Bq g(-1). In response, NPL prepared a single reference drum meeting this specification. The low density was achieved by loading the drum with plastic bottles, each partially loaded with ion-exchange resin. The resin in each bottle had been previously spiked with a mixture of (241)Am, (137)Cs and (60)Co, all traceable to national standards. The drum would be used primarily as the basis of a comparison exercise, but feedback on its usefulness as a calibration standard would also be sought. The drum was measured by 17 radioassay groups at 15 UK sites. The monitors used were mostly commercial gamma-spectrometry systems designed to accommodate waste drums. Some groups measured the drum on more than one monitor and some used more than one efficiency calibration. Many of the groups used mathematical modelling to derive their efficiencies. The results of the exercise were discussed at a second NPL workshop (2007), after which the participants were allowed to submit supplementary or replacement results (with reasons for any changes clearly stated). In total, 88 results were submitted. A total of 51 results were in agreement with the NPL values; of the remaining results, 24 were explained by the participants concerned (or were revised to provide supplementary values), but the other 13 results were either clearly discrepant or

  3. ANALYSIS OF AVAILABLE HYDROGEN DATA & ACCUMULATION OF HYDROGEN IN UNVENTED TRANSURANIC (TRU) DRUMS

    SciTech Connect

    DAYLEY, L

    2004-06-24

    This document provides a response to the second action required in the approval for the Justification for Continued Operations (JCO) Assay and Shipment of Transuranic (TRU) Waste Containers in 218-W-4C. The Waste Management Project continues to make progress toward shipping certified TRU waste to the Waste Isolation Pilot Plant (WIPP). As the existing inventory of TRU waste in the Central Waste Complex (CWC) storage buildings is shipped, and the uncovered inventory is removed from the trenches and prepared for shipment from the Hanford Site, the covered inventory of suspect TRU wastes must be retrieved and prepared for processing for shipment to WIPP. Accumulation of hydrogen in unvented TRU waste containers is a concern due to the possibility of explosive mixtures of hydrogen and oxygen. The frequency and consequence of these gas mixtures resulting in an explosion must be addressed. The purpose of this study is to recommend an approach and schedule for venting TRU waste containers in the low-level burial ground (LLBG) trenches in conjunction with TRU Retrieval Project activities. This study provides a detailed analysis of the expected probability of hydrogen gas accumulation in significant quantities in unvented drums. Hydrogen gas accumulation in TRU drums is presented and evaluated in the following three categories: Hydrogen concentrations less than 5 vol%; Hydrogen between 5-15 vol%; and Hydrogen concentrations above 15 vol%. This analysis is based on complex-wide experience with TRU waste drums, available experimental data, and evaluations of storage conditions. Data reviewed in this report includes experience from the Idaho National Environmental Engineering Laboratories (INEEL), Savannah River Site (SRS), Los Alamos National Laboratories (LANL), Oak Ridge National Laboratories, (ORNL), Rocky Flats sites, Matrix Depletion Program and the National Transportation and Packaging Program. Based on this analysis, as well as an assessment of the probability and

  4. Decreased sexual signalling reveals reduced viability in small populations of the drumming wolf spider Hygrolycosa rubrofasciata.

    PubMed Central

    Ahtiainen, Jari J.; Alatalo, Rauno V.; Mappes, Johanna; Vertainen, Laura

    2004-01-01

    One of the important goals in conservation biology is to determine reliable indicators of population viability. Sexual traits have been suggested to indicate population extinction risk, because they may be related to viability through condition dependence. Moreover, condition-dependent sexual traits may be more sensitive indicators of population viability than early life-history traits, because deleterious fitness effects of inbreeding tend to be expressed mainly at the end of the species' life history. However, empirical evidence of the significance of sexual behaviour for population viability is missing. In this study, we examined two male sexual traits and survival in 39 different-sized and isolated natural populations of the wolf spider, Hygrolycosa rubrofasciata. We also used several traits to estimate female reproductive success in 25 populations of H. rubrofasciata. According to previous studies, H. rubrofasciata males have a costly and condition-dependent acoustic signal, courtship drumming, which is the target of female choice. Males with a high drumming rate have considerably higher viability than males with a low drumming rate, and females that mate with the more actively drumming males gain genetic benefits in terms of increased offspring viability. Our results show that males in small populations had both lower survival and lower drumming rate than males in larger populations. However, we did not find any evidence for a decline in important early life-history traits (offspring number, hatching success or offspring body mass) or female body mass in small populations. Our results have two important messages for conservation biology. First, they show that sexual traits can be used as sensitive indicators of population viability. Second, the indirect benefits of female choice in terms of good genes might partially compensate for the reduction of viability in declining populations. Also, our results support the view that deleterious effects of small

  5. Granular avalanches in a two-dimensional rotating drum with imposed vertical vibration

    NASA Astrophysics Data System (ADS)

    Amon, Daniel L.; Niculescu, Tatiana; Utter, Brian C.

    2013-07-01

    We present statistics on granular avalanches in a rotating drum with and without imposed vertical vibration. The experiment consists of a quasi-two-dimensional, vertical drum containing pentagonal particles and rotated at a constant angular velocity. The drum rests on an electromagnetic shaker to allow vibration of the assembly as it rotates. We measure time series of the slope of the interface and find that the critical angle for slope failure θc and the resulting angle of repose θr are broadly distributed with an approximate power-law distribution of avalanches θc-θr for large avalanches. The faceted pentagonal grains used lead to significant interlocking with critical and repose angles (θc≈45∘ and θr≈39∘) larger than experiments using spherical grains, even with vibration, and avalanche magnitudes correlated with the prior build-up and anti-correlated with the prior avalanche. We find that the stability of the assembly increases with small vibrations and is destabilized at vibration amplitudes above a dimensionless acceleration (peak acceleration divided by acceleration due to gravity) of Γ=0.2. We also study history dependence of the avalanches by periodically oscillating the drum to compare the initial avalanche upon reversal of shear to steady-state distributions for avalanches during continuous rotation. We observe history dependence as an initial decrease in critical angle upon reversal of the drum rotation direction, indicating that a texture is induced to resist continued shear such that the surface is weaker to reversals in shear direction. Memory of this history is removed by sufficient external vibration (Γ≥0.8), which leads to compaction and relaxation of the surface layer grains responsible for avalanching dynamics, as initial and steady-state avalanche distributions become indistinguishable.

  6. Granular avalanches in a two-dimensional rotating drum with imposed vertical vibration.

    PubMed

    Amon, Daniel L; Niculescu, Tatiana; Utter, Brian C

    2013-07-01

    We present statistics on granular avalanches in a rotating drum with and without imposed vertical vibration. The experiment consists of a quasi-two-dimensional, vertical drum containing pentagonal particles and rotated at a constant angular velocity. The drum rests on an electromagnetic shaker to allow vibration of the assembly as it rotates. We measure time series of the slope of the interface and find that the critical angle for slope failure θ(c) and the resulting angle of repose θ(r) are broadly distributed with an approximate power-law distribution of avalanches θ(c)-θ(r) for large avalanches. The faceted pentagonal grains used lead to significant interlocking with critical and repose angles (θ(c)≈45° and θ(r)≈39°) larger than experiments using spherical grains, even with vibration, and avalanche magnitudes correlated with the prior build-up and anti-correlated with the prior avalanche. We find that the stability of the assembly increases with small vibrations and is destabilized at vibration amplitudes above a dimensionless acceleration (peak acceleration divided by acceleration due to gravity) of Γ=0.2. We also study history dependence of the avalanches by periodically oscillating the drum to compare the initial avalanche upon reversal of shear to steady-state distributions for avalanches during continuous rotation. We observe history dependence as an initial decrease in critical angle upon reversal of the drum rotation direction, indicating that a texture is induced to resist continued shear such that the surface is weaker to reversals in shear direction. Memory of this history is removed by sufficient external vibration (Γ≥0.8), which leads to compaction and relaxation of the surface layer grains responsible for avalanching dynamics, as initial and steady-state avalanche distributions become indistinguishable.

  7. Decreased sexual signalling reveals reduced viability in small populations of the drumming wolf spider Hygrolycosa rubrofasciata.

    PubMed

    Ahtiainen, Jari J; Alatalo, Rauno V; Mappes, Johanna; Vertainen, Laura

    2004-09-07

    One of the important goals in conservation biology is to determine reliable indicators of population viability. Sexual traits have been suggested to indicate population extinction risk, because they may be related to viability through condition dependence. Moreover, condition-dependent sexual traits may be more sensitive indicators of population viability than early life-history traits, because deleterious fitness effects of inbreeding tend to be expressed mainly at the end of the species' life history. However, empirical evidence of the significance of sexual behaviour for population viability is missing. In this study, we examined two male sexual traits and survival in 39 different-sized and isolated natural populations of the wolf spider, Hygrolycosa rubrofasciata. We also used several traits to estimate female reproductive success in 25 populations of H. rubrofasciata. According to previous studies, H. rubrofasciata males have a costly and condition-dependent acoustic signal, courtship drumming, which is the target of female choice. Males with a high drumming rate have considerably higher viability than males with a low drumming rate, and females that mate with the more actively drumming males gain genetic benefits in terms of increased offspring viability. Our results show that males in small populations had both lower survival and lower drumming rate than males in larger populations. However, we did not find any evidence for a decline in important early life-history traits (offspring number, hatching success or offspring body mass) or female body mass in small populations. Our results have two important messages for conservation biology. First, they show that sexual traits can be used as sensitive indicators of population viability. Second, the indirect benefits of female choice in terms of good genes might partially compensate for the reduction of viability in declining populations. Also, our results support the view that deleterious effects of small

  8. Steel Rattler

    NASA Astrophysics Data System (ADS)

    Trudo, Robert A.; Stotts, Larry G.

    1997-07-01

    Steel Rattler is a multi-phased project to determine the feasibility of using commercial off-the-shelf components in an advanced acoustic/seismic unattended ground sensor. This project is supported by the Defense Intelligence Agency through Sandia National Laboratories as the lead development agency. Steel Rattler uses advanced acoustic and seismic detection algorithms to categorize and identify various heavy vehicles down to the number of cylinders in the engine. This detection is accomplished with the capabilities of new, high-speed digital signal processors which analyze both acoustic and seismic data. The resulting analysis is compared against an onboard library of known vehicles and a statistical match is determined. An integrated thermal imager is also employed to capture digital thermal images for subsequent compression and transmission. Information acquired by Steel Rattler in the field is transmitted in small packets by a built-in low-power satellite communication system. The ground station receivers distribute the coded information to multiple analysis sites where the information is reassembled into coherent messages and images.

  9. Method of production H/sub 2/ using a rotating drum reactor with a pulse jet heat source

    DOEpatents

    Paulson, L.E.

    1988-05-13

    A method of producing hydrogen by an endothermic steam-carbon reaction using a rotating drum reactor and a pulse jet combustor. The pulse jet combustor uses coal dust as a fuel to provide reaction temperatures of 1300/degree/ to 1400/degree/F. Low-rank coal, water, limestone and catalyst are fed into the drum reactor where they are heated, tumbled and reacted. Part of the reaction product from the rotating drum reactor is hydrogen which can be utilized in suitable devices. 1 fig.

  10. Use of cold-bonded, waste oxide briquettes at U.S. Steel Mon Valley BOP shop

    SciTech Connect

    DiCaprio, V.; Howell, K.; Harris, R.; Toner, T.C.

    1995-09-01

    In attempts to avoid the escalated costs and environmental concerns associated with taking waste oxide materials to a landfill, National Recovery Systems Inc., in conjunction with US Steel, built a waste oxide briquetting facility at the USS Mon Valley works (Edgar Thomson plant) to recycle various sludges and scales. The waste oxide briquette is currently a blend of BOP classifier sludge, BOP filter drum sludge, casterscale and hot strip mill scale. In addition to the landfill cost avoidance, the waste oxide briquette is also a low cast, steel scrap supplement. This paper describes the production of the waste oxide briquette and the use of the recycled material at the Edgar Thomson BOP shop.

  11. Species profiles: life histories and environmental requirements of coastal fishes and invertebrates (Gulf of Mexico). Red drum. [Sciaenops ocellatus

    SciTech Connect

    Reagan, R.E.

    1985-06-01

    The red drum (Sciaenops ocellatus) is an estuarine dependent species. It spends its entire life in estuaries or nearshore coastal waters of the Gulf of Mexico. Red drum spawn from mid-August to November; peak spawning is from mid-September through October. Larvae and juveniles remain in estuaries and adults live along the coast and in passes. Commercial landings in Louisiana (1971-81) ranged from 723,700 to 2,212,500 lb. Texas closed commercial fishing in 1979. In most Gulf States, the sport catch usually exceeds commercial landings. There are few data on population dynamics of the species. Larval and juvenile red drum eat primarily invertebrates; adults feed on fish, shrimp, and crabs. Red drum tolerate a wide range of temperatures (2/sup 0/ to 37.5/sup 0/C) and salinities (0.14 to 50 ppt). 47 refs., 2 figs., 10 tabs.

  12. Metrological tests of a 200 L calibration source for HPGE detector systems for assay of radioactive waste drums.

    PubMed

    Boshkova, T; Mitev, K

    2016-03-01

    In this work we present test procedures, approval criteria and results from two metrological inspections of a certified large volume (152)Eu source (drum about 200L) intended for calibration of HPGe gamma assay systems used for activity measurement of radioactive waste drums. The aim of the inspections was to prove the stability of the calibration source during its working life. The large volume source was designed and produced in 2007. It consists of 448 identical sealed radioactive sources (modules) apportioned in 32 transparent plastic tubes which were placed in a wooden matrix which filled the drum. During the inspections the modules were subjected to tests for verification of their certified characteristics. The results show a perfect compliance with the NIST basic guidelines for the properties of a radioactive certified reference material (CRM) and demonstrate the stability of the large volume CRM-drum after 7 years of operation.

  13. The design of a mechanical referencing system for the rear drum of the Longwall Shearer Coal Miner

    NASA Technical Reports Server (NTRS)

    Jones, E. W.; Yang, T. C. H.

    1981-01-01

    The design of two systems which reference the position of a longwall shearer coal miner to the mine roof of the present cut and of the last cut are presented. This system is part of an automation system that will guide the rear cutting drum in such a manner that the total depth of cut remains constant even though the front drum may be following an undulating roof profile. The rear drum referencing mechanism continually monitors the distance from the mine roof to the floor for the present cut. This system provides a signal to control a constant depth of cut. The last cut follower mechanism continually monitors the distance from the mine roof of the prior cut to the cutting drum. This latter system provides a signal to minimize the step height in the roof between cuts. The dynamic response of this hydraulic-pneumatic and mechanical system is analyzed to determine accumulator size and precharge pressure.

  14. Motion sickness and gastric myoelectric activity as a function of speed of rotation of a circular vection drum

    NASA Technical Reports Server (NTRS)

    Hu, Senqi; Stern, Robert M.; Vasey, Michael W.; Koch, Kenneth L.

    1989-01-01

    Motion sickness symptoms and electrogastrograms (EGGs) were obtained from 60 healthy subjects while they viewed an optokinetic drum rotated at one of four speeds: 15, 30, 60 or 90 deg/s. All subjects experienced vection, illusory self-motion. Motion sickness symptoms increased as drums speed increased up to 60 deg/s. Power, spectral intensity, of the EGG at the tachygastria frequencies (4-9 cpm) was calculated at each drum rotation speed. The correlation between the motion sickness symptoms and the power at 4-9 cpm was significant. Thus, drum rotation speed influenced the spectral power of the EGG at 4-9 cpm, tachygastria, and the intensity of motion sickness symptoms.

  15. Safety evaluation for packaging (onsite) for concrete-shielded RHTRU waste drum for the 327 postirradiation testing laboratory

    SciTech Connect

    Adkins, H.E.

    1996-10-29

    This safety evaluation for packaging authorizes onsite transport of Type B quantities of radioactive material in the Concrete- Shielded Remote-Handled Transuranic Waste (RH TRU) Drum per WHC-CM-2-14, Hazardous Material Packaging and Shipping. The drum will be used for transport of 327 Building legacy waste from the 300 Area to the Transuranic Waste Storage and Assay Facility in the 200 West Area and on to a Solid Waste Storage Facility, also in the 200 Area.

  16. Safety evaluation for packaging (onsite) for the concrete-shielded RH TRU drum for the 327 Postirradiation Testing Laboratory

    SciTech Connect

    Smith, R.J.

    1998-03-31

    This safety evaluation for packaging authorizes onsite transport of Type B quantities of radioactive material in the Concrete Shielded Remote-Handled Transuranic Waste (RH TRU) Drum per HNF-PRO-154, Responsibilities and Procedures for all Hazardous Material Shipments. The drum will be used for transport of 327 Building legacy waste from the 300 Area to a solid waste storage facility on the Hanford Site.

  17. PERMANENT GENETIC RESOURCES: PCR primers for 100 microsatellites in red drum (Sciaenops ocellatus).

    PubMed

    Karlsson, Sten; Renshaw, Mark A; Rexroad Iii, Caird E; Gold, John R

    2008-03-01

    One hundred nuclear-encoded microsatellites from a genomic library of red drum (Sciaenops ocellatus) were isolated and characterized. Eight microsatellites had tetranucleotide motifs; 92 had dinucleotide motifs. The average number of alleles per microsatellite (sample of 22-24 fish) was 17.7 (range = 2-30); gene diversity averaged 0.796 (range = 0.227-1.000). Following Bonferroni correction, genotype frequencies at 90 microsatellites did not deviate significantly from Hardy-Weinberg equilibrium expectations. Occurrence of null alleles was inferred at 15 microsatellites; alleles differing by only a single base were observed at 11 microsatellites. The microsatellites developed should prove useful for population-genetic studies of 'wild' red drum and in construction of a genetic map.

  18. Ecological performance of red drum (Sciaenops ocellatus) larvae exposed to environmental levels of the insecticide malathion.

    PubMed

    Del Carmen Alvarez, Maria; Fuiman, Lee A

    2006-05-01

    Malathion is a highly soluble organophosphate insecticide that is widely used in agriculture and mosquito eradication campaigns. Fish species, such as red drum (Sciaenops ocellatus), that use seagrass beds as nursery areas could be affected by runoff waters contaminated with malathion. We exposed red drum larvae at the size they reach in estuarine nursery areas to environmentally realistic and sublethal levels of malathion (0, 1, and 10 microg/L). We evaluated the effects of such exposure on ecologically significant behaviors (routine swimming and predator evasion), growth, and resting metabolism. Malathion exposure to relatively low but ecologically realistic concentrations did not affect routine behavior, escape behavior, resting metabolic rate, or growth, indicating that reported environmental levels may be safe for young fishes. However, a recent substantial increase in the use of malathion may elevate surface-water concentrations to levels above those tested in the present study.

  19. Analysis Methodologies and Ameliorative Techniques for Mitigation of the Risk in Churches with Drum Domes

    NASA Astrophysics Data System (ADS)

    Zingone, Gaetano; Calogero, Cucchiara; Licata, Vincenzo

    2008-07-01

    The present work fits into the interesting theme of seismic prevention for protection of the monumental patrimony made up of churches with drum domes. Specifically, with respect to a church in the historic area of Catania, chosen as a monument exemplifying the typology examined, the seismic behavior is analyzed in the linear field using modern dynamic identification techniques. The dynamically identified computational model arrived at made it possible to identify the macro-element most at risk, the dome-drum system. With respect to this system the behavior in the nonlinear field is analyzed through dynamic tests on large-scale models in the presence of various types of improving reinforcement. The results are used to appraise the ameliorative contribution afforded by each of them and to choose the most suitable type of reinforcement, optimizing the stiffness/ductility ratio of the system.

  20. Optimal efficiency vector control of induction motor drive system for drum washing machine

    NASA Astrophysics Data System (ADS)

    Lee, Won Cheol; Yu, Jae Sung; Jang, Bong An; Won, Chung Yuen

    2005-12-01

    In home appliances, electric energy is optimally controlled by using power electronics technology, creating a comfortable environment in terms of energy saving, low sound generation, and reduced time consumption. Usually simplicity and robustness make the three phase induction motor attractive for use in domestic appliance, including washing machines. Two main types of domestic washing machine have evolved. We focus on efficiency of the front loading machine favored in Europe, which has a horizontal drum axis. This paper presents the control algorithm for optimal efficiency drives of an induction motor for drum washing machine. This system uses a simple model of the induction motor that include equations of the iron losses. The proposed optimal efficiency control algorithm calculates commands of the reference torque and flux currents for the flux oriented control of the induction motor. The proposed algorithm is verified through digital simulation.

  1. Effects of pre-exposures to a rotating optokinetic drum on adaptation to motion sickness

    NASA Technical Reports Server (NTRS)

    Hu, Senqi; Stern, Robert M.; Koch, Kenneth L.

    1991-01-01

    The effects of two different preexposure procedures on the adaptation to motion-sickness-causing rotation motion in a rotating optokinetic drum were investigated in three groups of human subjects. The first (control) group had a standard 16-min exposure in a drum rotating at 60 deg/sec, with no preexposure. The second (incremental exposure) group had two separated 4-min preexposure periods, at 15 deg/min and 30 deg/min, immediately prior to the standard 16-min exposure. The third (abrupt exposure) group had the same preexposure but with the second rotation at 60 deg/min, followed by the standard exposure. It was found that subjects in the incremental exposure group had significantly fewer motion sickness symptoms during the standard rotation period than did the subjects in the other two groups.

  2. Analog of the Kutateladze crisis and uplifting water formation in drum boiler

    SciTech Connect

    Shreiber, I.

    1995-07-01

    The paper deals with a model for the formation of a vapor bubble cavitation zone within a water layer due to a rarefied wave propagating in a drum boiler circulation circuit. The water in the layer is close to the saturation line (subheated). Models are presented for vapor cavitation zone development, pressure field formation and the phenomenon of swelling. The specific feature of the cavitation problem is the multiply reflected rarefied wave at the bottom and the formation of the most intensive cavitation zone near the bottom. The coalescing and floating bubbles can uplift the water layer and create an emergency situation in the control of the drum. The phenomenon is similar to the Kutateladze crisis for boiling liquid near a wall. The control system of the power station must take into account the danger of such uplifting.

  3. Multisensory integration of drumming actions: musical expertise affects perceived audiovisual asynchrony.

    PubMed

    Petrini, Karin; Dahl, Sofia; Rocchesso, Davide; Waadeland, Carl Haakon; Avanzini, Federico; Puce, Aina; Pollick, Frank E

    2009-09-01

    We investigated the effect of musical expertise on sensitivity to asynchrony for drumming point-light displays, which varied in their physical characteristics (Experiment 1) or in their degree of audiovisual congruency (Experiment 2). In Experiment 1, 21 repetitions of three tempos x three accents x nine audiovisual delays were presented to four jazz drummers and four novices. In Experiment 2, ten repetitions of two audiovisual incongruency conditions x nine audiovisual delays were presented to 13 drummers and 13 novices. Participants gave forced-choice judgments of audiovisual synchrony. The results of Experiment 1 show an enhancement in experts' ability to detect asynchrony, especially for slower drumming tempos. In Experiment 2 an increase in sensitivity to asynchrony was found for incongruent stimuli; this increase, however, is attributable only to the novice group. Altogether the results indicated that through musical practice we learn to ignore variations in stimulus characteristics that otherwise would affect our multisensory integration processes.

  4. a Study on the Squeal of a Drum Brake which has Shoes of Non-Uniform Cross-Section

    NASA Astrophysics Data System (ADS)

    LEE, J. M.; YOO, S. W.; KIM, J. H.; AHN, C. G.

    2001-03-01

    A stability analysis of a drum brake, which has shoes of non-uniform cross-section, is performed to find a simple and effective method of reducing the squeal of the drum brake by partially changing the shapes of the shoes. The squeal is considered as a noise induced by the self-excited vibration of the drum brake which makes the brake unstable. Shoes of non-uniform cross-section are often used for the drum brake of current passenger cars to reduce the squeal. However, the influence of this non-uniformity upon the squeal has not been analyzed theoretically. In this study, the drum and the shoes are assumed as a uniform ring and non-uniform arches, respectively, for modelling the brake. For a reasonable method of modelling, the vibration characteristics of the brake and their relations to the squeal are discussed based on the results of modal tests. The influences of brake design parameters upon the squeal are investigated, and a minor change of the cross-section is proposed to reduce the squeal. The effect of the minor change is verified through noise dynamometer tests. In addition, the effect of asymmetry of the drum, which can be built by mass addition, is presented.

  5. Characterization of hepatic low-K(m) outer-ring deiodination in red drum (Sciaenops ocellatus).

    PubMed

    VanPutte, C L; MacKenzie, D S; Eales, J G

    2001-03-01

    The more biologically active thyroid hormone 3,5,3'-triiodothyronine (T(3)), is primarily derived from peripheral deiodination of thyroxine (T(4)). We characterized hepatic deiodination for a commercially important, warm water teleost fish, the red drum (Sciaenops ocellatus). Low K(m) outer-ring deiodination (ORD) activity was determined by production of free iodide ((125)I) upon incubation of hepatic microsomes with radiolabeled T(4). HPLC analysis demonstrated that (125)I, and T(3) were produced in equal amounts, thereby validating 125I as a measure of T(3) production. A small amount of 3,3',5'-triiodothyronine (reverse T(3)) was also produced by inner-ring deiodination. Production of (125)I was linear over a range of 0--100 microg protein/ml and for incubations of 30 min--4 h. Maximal ORD activity was measured at pH 6.6, 50 mM dithiothreitol (DTT) and an incubation temperature of 20 degrees C. Double reciprocal plots demonstrated that the average apparent K(m) was 5.1 nM and the average V(max) was 3.7 pmol T(4) converted/h per mg protein. ORD was not inhibited by propylthiouracil but was 50% inhibited by 90 microM of iodoacetic acid and 7 microM of gold thioglucose. The substrate analog preference was T(4) = tetraiodoacetic acid = reverse T(3) > triiodoacetic acid > T(3). In relation to other tissues, ORD for liver>gill>intestine>kidney. Similar hepatic deiodination activity was present in adult wild, aquacultured and laboratory-reared red drum, but in adult wild red drum the optimum temperature was higher. Red drum hepatic low-K(m) deiodination activity appears to most closely resemble rainbow trout hepatic and mammalian Type II deiodination. Evidence of inner-ring T(4) deiodination suggests a more active hepatic iodothyronine catabolic pathway than in other teleost species.

  6. Flow rate testing of valves used with the 500 gallon collapsible drum

    NASA Astrophysics Data System (ADS)

    Perdue, William D.

    1992-04-01

    This report covers the test and evaluation of four couplings/valves used with the 500-gallon collapsible drum: the existing poppet valve, a new redesigned poppet valve, a Carter refuel/defuel valve that works in conjunction with the single point refueling nozzle, and a Kamvalok dry-break coupling valve. The purpose of this testing was to determine maximum flow capability of each valve design and identify any new characteristics that may impact performance of the FARE system.

  7. Study of Asphaltic Concrete Produced in Dryer Drum Mixers for Airport Pavements.

    DTIC Science & Technology

    1976-10-01

    STWDARDS-163- w S 4 -- , ,a, i I Report No-c FAA-RD-76-165 STUDY OF ASPHALTIC CONCRETE PRODUCED IN DRYER DRUM MIXERS FOR AIRPORT PAVEMENTS 0 E. T...PREFACE This study was supported by the Systems Research and Development Service of the Federal Aviation Administration. This is a final report presenting...the asphaltic concrete . In September, 1976 the Alaskan Region of FAA reported that the runway pavement had transverse thermal cracks approximately 200

  8. 49 CFR 393.47 - Brake actuators, slack adjusters, linings/pads and drums/rotors.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... steering axle of a truck, truck-tractor or bus shall not be less than 4.8 mm (3/16 inch) at the shoe center for a shoe with a continuous strip of lining; less than 6.4 mm (1/4 inch) at the shoe center for a shoe with two pads; or worn to the wear indicator if the lining is so marked, for air drum brakes....

  9. 49 CFR 393.47 - Brake actuators, slack adjusters, linings/pads and drums/rotors.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... steering axle of a truck, truck-tractor or bus shall not be less than 4.8 mm (3/16 inch) at the shoe center for a shoe with a continuous strip of lining; less than 6.4 mm (1/4 inch) at the shoe center for a shoe with two pads; or worn to the wear indicator if the lining is so marked, for air drum brakes....

  10. 49 CFR 393.47 - Brake actuators, slack adjusters, linings/pads and drums/rotors.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... steering axle of a truck, truck-tractor or bus shall not be less than 4.8 mm (3/16 inch) at the shoe center for a shoe with a continuous strip of lining; less than 6.4 mm (1/4 inch) at the shoe center for a shoe with two pads; or worn to the wear indicator if the lining is so marked, for air drum brakes....

  11. 49 CFR 393.47 - Brake actuators, slack adjusters, linings/pads and drums/rotors.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... steering axle of a truck, truck-tractor or bus shall not be less than 4.8 mm (3/16 inch) at the shoe center for a shoe with a continuous strip of lining; less than 6.4 mm (1/4 inch) at the shoe center for a shoe with two pads; or worn to the wear indicator if the lining is so marked, for air drum brakes....

  12. Supertough Stainless Bearing Steel

    NASA Technical Reports Server (NTRS)

    Olson, Gregory B.

    1995-01-01

    Composition and processing of supertough stainless bearing steel designed with help of computer-aided thermodynamic modeling. Fracture toughness and hardness of steel exceeds those of other bearing steels like 440C stainless bearing steel. Developed for service in fuel and oxidizer turbopumps on Space Shuttle main engine. Because of strength and toughness, also proves useful in other applications like gears and surgical knives.

  13. Performance test of a gamma/neutron mapper on stored TRU waste drums at the RWMC

    SciTech Connect

    Gehrke, R.J.; Josten, N.E.; Lawrence, R.S.

    1995-12-01

    The results from a performance test of a {gamma}- and neutron-radiation measurement instrument used to provide two-dimensional radiation field maps are reported. The performance test was conducted at the Transuranic Storage Area of the Radioactive Waste Management Complex (RWMC) where interim storage is provided for 55-gal. drums of TRU waste from the Department of Energy`s Rocky Flats Plant. The performance test consisted of scanning drums stacked five high and five wide to identify high radiation areas and possible discrepancies with the waste manifest. Scans were taken at standoff distances of 15 cm, 30 cm, 45 cm and 90 cm. Data were acquired at scan speeds of 7.5 cm/s and 15 cm/s. The results of these scans are presented as one, two and three dimensional contour plots of the radiation fields. A comparison of these results with manifests of these drums are compared and discussed. While the T-radiation fields as measured by the Health Physicist and by the radiation maps are in general in agreement, the TRU content as given in the manifest did not often correlate with the neutron map.

  14. Carbon decomposition by inoculating Phanerochaete chrysosporium during drum composting of agricultural waste.

    PubMed

    Varma, V Sudharsan; Ramu, Kamma; Kalamdhad, Ajay S

    2015-05-01

    The effect of Phanerochaete chrysosporium inoculation during drum composting of agricultural waste was performed at different composting stages. Three trials were carried out with (5:4:1) combination of vegetable waste, cattle manure, and sawdust along with 10 kg of dried leaves with a total mass of 100 kg in a 550 L rotary drum composter. Trial 1 was a control without inoculation of fungus, while trial 2 was inoculated during the initial day (0th day of composting), and trial 3 was inoculated after the thermophilic phase, i.e., on the 8th day of composting period. The inoculation of fungus increased the volatile solids reduction by 1.45-fold in trial 2 and 1.7-fold in trial 3 as compared to trial 1 without any fungal inoculation. Total Kjeldahl Nitrogen (TKN) was observed with 2.31, 2.62, and 2.59% in trials 1, 2, and 3, respectively, at the end of 20 days of composting period. Hence, it can be concluded that inoculation of white-rot fungus increased the decomposition rate of agricultural waste within shorter time in drum composting. However, inoculation after the thermophilic phase was found more effective than inoculation during initial days of composting for producing more stabilized and nutrient-rich compost.

  15. Cardiac function and survival are affected by crude oil in larval red drum, Sciaenops ocellatus.

    PubMed

    Khursigara, Alexis J; Perrichon, Prescilla; Martinez Bautista, Naim; Burggren, Warren W; Esbaugh, Andrew J

    2017-02-01

    Following exposure to weathered and non-weathered oil, lethal and sub-lethal impacts on red drum larvae were assessed using survival, morphological, and cardiotoxicity assays. The LC50 for red drum ranged from 14.6 (10.3-20.9) to 21.3 (19.1-23.8) μgl(-1) ΣPAH with no effect of exposure timing during the pre-hatch window or oil weathering. Similarly, morphological deformities showed dose responses in the low ppb range. Cardiac output showed similar sensitivity resulting in a major 70% reduction after exposure to 2.6μgl(-1) ΣPAH. This cardiac failure was driven by reduced stroke volume rather than bradycardia, meaning that in some species, cardiac function is more sensitive than previously thought. After the Deepwater Horizon oil spill, much of this type of work has primarily focused on pelagic species with little known about fast developing estuarine species. These results demonstrate similarity sensitivity of the red drum as their pelagic counter parts, and more importantly, that cardiac function is dramatically reduced in concert with pericardial edema.

  16. Use of comparative genomics to develop EST-SSRs for red drum (Sciaenops ocellatus).

    PubMed

    Hollenbeck, Christopher M; Portnoy, David S; Gold, John R

    2012-12-01

    Microsatellites physically linked to expressed sequence tags (EST-SSRs) are an important resource for linkage mapping and comparative genomics, and data mining in publicly available EST databases is a common strategy for EST-SSR discovery. At present, many species lack species-specific EST sequence data needed for the efficient characterization of EST-SSRs. This paper describes the discovery and development of EST-SSRs for red drum (Sciaenops ocellatus), an estuarine-dependent sciaenid species of economic importance in the USA and elsewhere, using a phylogenetically informed, comparative genomics approach to primer design. The approach entailed comparing existing genomic resources from species closely allied phylogenetically to red drum, with resources from more distantly related outgroup species. By taking into account the degree to which flanking regions are conserved across taxa, the efficiency of PCR primer design was increased greatly. The amplification success rate for primers designed for red drum was 100 % when using EST libraries from confamilial species and 92 % when using an EST library from a species in the same suborder. The primers developed also amplified EST-SSRs in a wide range of perciform fishes, suggesting potential use in comparative genomics. This study demonstrates that EST-SSRs can be efficiently developed for an organism when limited species-specific data are available by exploiting genomic resources from well-studied species, even those at extended phylogenetic distances.

  17. Linkage Mapping and Comparative Genomics of Red Drum (Sciaenops ocellatus) Using Next-Generation Sequencing.

    PubMed

    Hollenbeck, Christopher M; Portnoy, David S; Wetzel, Dana; Sherwood, Tracy A; Samollow, Paul B; Gold, John R

    2017-03-10

    Developments in next-generation sequencing allow genotyping of thousands of genetic markers across hundreds of individuals in a cost-effective manner. Because of this, it is now possible to rapidly produce dense genetic linkage maps for nonmodel species. Here, we report a dense genetic linkage map for red drum, a marine fish species of considerable economic importance in the southeastern United States and elsewhere. We used a prior microsatellite-based linkage map as a framework and incorporated 1794 haplotyped contigs derived from high-throughput, reduced representation DNA sequencing to produce a linkage map containing 1794 haplotyped restriction-site associated DNA (RAD) contigs, 437 anonymous microsatellites, and 44 expressed sequence-tag-linked microsatellites (EST-SSRs). A total of 274 candidate genes, identified from transcripts from a preliminary hydrocarbon exposure study, were localized to specific chromosomes, using a shared synteny approach. The linkage map will be a useful resource for red drum commercial and restoration aquaculture, and for better understanding and managing populations of red drum in the wild.

  18. Linkage Mapping and Comparative Genomics of Red Drum (Sciaenops ocellatus) Using Next-Generation Sequencing

    PubMed Central

    Hollenbeck, Christopher M.; Portnoy, David S.; Wetzel, Dana; Sherwood, Tracy A.; Samollow, Paul B.; Gold, John R.

    2017-01-01

    Developments in next-generation sequencing allow genotyping of thousands of genetic markers across hundreds of individuals in a cost-effective manner. Because of this, it is now possible to rapidly produce dense genetic linkage maps for nonmodel species. Here, we report a dense genetic linkage map for red drum, a marine fish species of considerable economic importance in the southeastern United States and elsewhere. We used a prior microsatellite-based linkage map as a framework and incorporated 1794 haplotyped contigs derived from high-throughput, reduced representation DNA sequencing to produce a linkage map containing 1794 haplotyped restriction-site associated DNA (RAD) contigs, 437 anonymous microsatellites, and 44 expressed sequence-tag-linked microsatellites (EST-SSRs). A total of 274 candidate genes, identified from transcripts from a preliminary hydrocarbon exposure study, were localized to specific chromosomes, using a shared synteny approach. The linkage map will be a useful resource for red drum commercial and restoration aquaculture, and for better understanding and managing populations of red drum in the wild. PMID:28122951

  19. DEM simulation of particle mixing for optimizing the overcoating drum in HTR fuel fabrication

    NASA Astrophysics Data System (ADS)

    Liu, Malin; Lu, Zhengming; Liu, Bing; Shao, Youlin

    2013-06-01

    The rotating drum was used for overcoating coated fuel particles in HTR fuel fabrication process. All the coated particles should be adhered to equal amount of graphite powder, which means that the particle should be mixed quickly in both radial and axial directions. This paper investigated the particle flow dynamics and mixing behavior in different regimes using the discrete element method (DEM). By varying the rotation speed, different flow regimes such as slumping, rolling, cascading, cataracting, centrifuging were produced. The mixing entropy based on radial and axial grid was introduced to describe the radial and axial mixing behaviors. From simulation results, it was found that the radial mixing can be achieved in the cascading regime more quickly than the slumping, rolling and centrifuging regimes, but the traditional rotating drum without internal components can not achieve the requirements of axial mixing and should be improved. Three different structures of internal components are proposed and simulated. The new V-shaped deflectors were found to achieve a quick axial mixing behavior and uniform axial distribution in the rotating drum based on simulation results. At last, the superiority was validated by experimental results, and the new V-shaped deflectors were used in the industrial production of the overcoating coated fuel particles in HTR fuel fabrication process.

  20. Growth, reproduction, mortality, distribution, and biomass of freshwater drum in Lake Erie

    USGS Publications Warehouse

    Bur, Michael T.

    1984-01-01

    Predominant age-groups in the Lake Erie freshwater drum Aplodinotus grunnienspopulation were 3, 4, and 5 as determined from gill net, trap net, bottom trawl, and midwater trawl samples. Age and growth calculations indicated that females grew faster than males. However, the length-weight relation did not differ between sexes and was described by the equation: log W = −5.4383 + 3.1987 log L. Some males became sexually mature at age 2 and all were mature by age 6. Females matured 1 year later than males. Three sizes of eggs were present in ovaries; the average total number was 127,000 per female for 20 females over a length range of 270 to 478 mm. Seasonal analysis of the ovary-body weight ratio indicated that spawning extended from June to August. A total annual mortality rate of 49% for drum aged 4 through 11 was derived from catch-curve analysis. Freshwater drum were widely distributed throughout Lake Erie in 1977–1979, the greatest concentration being in the western basin. They moved into warm, shallow water (less than 10 m deep) during summer, and returned to deeper water in late fall. Summer biomass estimates for the western basin, based on systematic surveys with bottom trawls, were 9,545 t in 1977 and 2,333 t in 1978.

  1. Weld repair of carbon-moly coke drums without postweld heat treatment

    SciTech Connect

    Moore, D.E.

    1996-06-01

    Investigations to evaluate weld repair of C-{1/2}Mo coke drums without postweld heat treatment (PWHT) are discussed in this paper. These investigations showed that shielded metal-arc welding (SMAW) without PWHT produced heat-affected zones (HAZ) and weld deposits with Charpy V-notch (CVN) impact toughness that exceeded the toughness of ex-service plate material. PWHT de-embrittles strain age-embrittled ex-service plate material. However, warming of drums to 200 F before putting in feed compensates for the omission of the de-embrittling PWHT. Additional testing showed that the de-embrittling PWHT did not significantly improve the fatigue properties of the ex-service plate material. As-welded SMAW repairs were found to be feasible for coke drums, and repairs have now been in service successfully for up to 2 years. The as-welded SMAW repairs were qualified on the basis of a 300 F preheat using small diameter electrodes for the first pass followed by larger diameter electrodes to temper the HAZ of the first pass. A half-bead technique was not used. Heat input is not precisely controlled as would be required for controlled deposition welding. Following the implementation of SMAW repairs without PWHT, the author extended the work to include as-welded repairs with automatic gas metal-arc welding (GMAW).

  2. Demand-side management implementation and verification at Fort Drum, New York

    SciTech Connect

    Armstrong, P.R.; Dixon, D.R.; Richman, E.E.; Rowley, S.E.

    1994-12-01

    Through the Facility Energy Decision Screening (FEDS) process, the US Army Forces Command (FORSCOM) has identified present value savings of nearly $47 million in cost-effective energy conservation measures (ECMs) at Fort Drum, New York. With associated costs of more than $16 million (1992 $), the measures provide a net present value of $30.6 million for all identified projects. By implementing all cost-effective ECMs, Fort Drum can reduce its annual energy use by more than 230,000 MBtu (11% of its fossil energy consumption) and more than 27,000 MWh (32% of its electric energy consumption). The annual cost of energy services will decrease by $2.8 million (20%) at current energy rates. The servicing utility (Niagara Mohawk Power Corporation) has informally agreed to finance and implement cost-effective ECMs and to participate in the verification of energy savings. Verification baselining is under way; implementation of retrofit projects is expected to begin in late 1994. The utility-administered financing and contracting arrangements and the alternative federal programs for implementing the projects are described. The verification protocols and sampling plans for audit, indirect, and direct measurement levels of verification and the responsibilities of Fort Drum, the utility, the energy service companies (ESCOs), and Pacific Northwest Laboratory (PNL) in the verification process are also presented. A preliminary weather-normalized model of baseline energy consumption has been developed based on a full year`s metered data.

  3. Salt Composition Derived from Veazey Composition by Thermodynamic Modeling and Predicted Composition of Drum Contents

    SciTech Connect

    Weisbrod, Kirk Ryan; Veirs, Douglas Kirk; Funk, David John; Clark, David Lewis

    2016-03-11

    This report describes the derivation of the salt composition from the Veazey salt stream analysis. It also provides an estimate of the proportions of the kitty litter, nitrate salt and neutralizer that was contained in drum 68660. While the actinide content of waste streams was judiciously followed in the 1980s in TA-55, no record of the salt composition could be found. Consequently, a salt waste stream produced from 1992 to 1994 and reported by Gerry Veazey provided the basis for this study. While chemical analysis of the waste stream was highly variable, an average analysis provided input to the Stream Analyzer software to calculate a composition for a concentrated solid nitrate salt and liquid waste stream. The calculation predicted the gas / condensed phase compositions as well as solid salt / saturated liquid compositions. The derived composition provides an estimate of the nitrate feedstream to WIPP for which kinetic measurements can be made. The ratio of salt to Swheat in drum 68660 contents was estimated through an overall mass balance on the parent and sibling drums. The RTR video provided independent confirmation concerning the volume of the mixture. The solid salt layer contains the majority of the salt at a ratio with Swheat that potentially could become exothermic.

  4. Motion sickness severity and physiological correlates during repeated exposures to a rotating optokinetic drum

    NASA Technical Reports Server (NTRS)

    Hu, Senqi; Grant, Wanda F.; Stern, Robert M.; Koch, Kenneth L.

    1991-01-01

    Fifty-two subjects were exposed to a rotating optokinetic drum. Ten of these subjects who became motion sick during the first session completed two additional sessions. Subjects' symptoms of motion sickness, perception of self-motion, electrogastrograms (EGGs), heart rate, mean successive differences of R-R intervals (RRI), and skin conductance were recorded for each session. The results from the first session indicated that the development of motion sickness was accompanied by increased EGG 4-9 cpm activity (gastric tachyarrhythmia), decreased mean succesive differences of RRI, increased skin conductance levels, and increased self-motion perception. The results from the subjects who had three repeated sessions showed that 4-9 cpm EGG activity, skin conductance levels, perception of self-motion, and symptoms of motion sickness all increased significantly during the drum rotation period of the first session, but increased significantly less during the following sessions. Mean successive differences of RRI decreased significantly during the drum rotation period for the first session, but decreased significantly less during the following sessions. Results show that the development of motion sickness is accompanied by an increase in gastric tachyarrhythmia, and an increase in sympathetic activity and a decrease in parasympathetic activity, and that adaptation to motion sickness is accompanied by the recovery of autonomic nervous system balance.

  5. Application of remote Raman screening to processing of mixed wastes in drums

    SciTech Connect

    Crawford, B.A.; Jewett, J.R.; Parker, K.E.; Petersen, C.A.

    1993-02-01

    Disposal of transuranic and low-level drum waste involves decisions based on transportation restrictions, Waste Isolation Pilot Project - Waste Acceptance Criteria, and regulation resulting from the Resource Conservation and Recovery Act of 1976 and the Washington State Department of Ecology. To support the decisions made concerning final disposition of these wastes, characterization protocols must be established that ultimately aid in defining the environmental impact. Under current methods, Intensive and expensive laboratory analyses are requested to support these decisions. Alternative screening analyses have been investigated to support characterization and reduce costs and sample turn-around times. One promising screening technique involves application of remote Raman spectroscopy for identification of unknown salts, sludges, and solids in wastes. Raman spectroscopy when used with real-time radiography and visual documentation expands the information base available for making real-time decisions for treatment of diverse drummed radioactive solid waste in a waste processing facility. Fourier Transform Raman spectroscopy has been successfully employed to identify oxidizing reagent waste solutions disposed on vermiculite. In addition, it has been proven that low concentrations of material in binary salt mixtures can be detected by using fiber optic remote Fourier Transform Raman spectroscopy. Development of an extensive solid waste libraryis a key element in the deployment of this technology in the process environment of solid waste drums and barrels.

  6. Combined discrete particle and continuum model predicting solid-state fermentation in a drum fermentor.

    PubMed

    Schutyser, M A I; Briels, W J; Boom, R M; Rinzema, A

    2004-05-20

    The development of mathematical models facilitates industrial (large-scale) application of solid-state fermentation (SSF). In this study, a two-phase model of a drum fermentor is developed that consists of a discrete particle model (solid phase) and a continuum model (gas phase). The continuum model describes the distribution of air in the bed injected via an aeration pipe. The discrete particle model describes the solid phase. In previous work, mixing during SSF was predicted with the discrete particle model, although mixing simulations were not carried out in the current work. Heat and mass transfer between the two phases and biomass growth were implemented in the two-phase model. Validation experiments were conducted in a 28-dm3 drum fermentor. In this fermentor, sufficient aeration was provided to control the temperatures near the optimum value for growth during the first 45-50 hours. Several simulations were also conducted for different fermentor scales. Forced aeration via a single pipe in the drum fermentors did not provide homogeneous cooling in the substrate bed. Due to large temperature gradients, biomass yield decreased severely with increasing size of the fermentor. Improvement of air distribution would be required to avoid the need for frequent mixing events, during which growth is hampered. From these results, it was concluded that the two-phase model developed is a powerful tool to investigate design and scale-up of aerated (mixed) SSF fermentors.

  7. Effects of somatolactin on melanosome aggregation in the melanophores of red drum (Sciaenops ocellatus) scales.

    PubMed

    Zhu, Y; Thomas, P

    1997-01-01

    The effects of purified red drum somatolactin on pigment movement in red drum scales were studied in vitro and in vivo. The integument became pale within 2 min following an intramuscular injection of somatolactin (1 nmol/g body weight) in fish held in a black-background aquarium, and gradually regained its black coloration during the subsequent 30 min. No melanosome aggregation was observed in fish injected with vehicle or somatolactin over the dose range of 10(-9)-10(2) pmol/g. Melanosomes in the melanophores of scales were completely aggregated within 10 min of incubation with 1 microM somatolactin in vitro. The effect of somatolactin on melanosome aggregation was dose-dependent. Somatolactin caused only partial aggregation at a concentration of 500 nM and 250 nM somatolactin had little or no effect. Somatolactin caused melanosome aggregation in both innervated and denervated melanophores. Aggregated melanosomes which had been preincubated with somatolactin dispersed within 30 min after rinsing with a physiological buffer. No melanosome aggregation was observed in scales incubated with 10 nM-1 microM of red drum prolactin (PRL), red drum growth hormone (GH), ovine PRL, or recombinant tuna GH. These results indicate that the action of somatolactin on melanosome movement is direct, specific, reversible, and is probably mediated by a specific somatolactin receptor on the melanophores. Melanin-concentrating hormone (MCH) and norepinephrine (NE) also induced melanosome aggregation in scales at a low concentration of 10 nM. Addition of 1 microM alpha-melanophore-stimulating hormone (alpha-MSH) following preincubation of scales with 1 microM somatolactin, 10 nM MCH, or 10 nM NE resulted in partial dispersion of the melanosomes. These results suggest that melanosome migration in red drum scales is under multiple hormonal control. Although a direct action of somatolactin on melanosome aggregation is demonstrated in this study, its physiological role in the regulation of

  8. Analysis of heat conduction in a drum brake system of the wheeled armored personnel carriers

    NASA Astrophysics Data System (ADS)

    Puncioiu, A. M.; Truta, M.; Vedinas, I.; Marinescu, M.; Vinturis, V.

    2015-11-01

    This paper is an integrated study performed over the Braking System of the Wheeled Armored Personnel Carriers. It mainly aims to analyze the heat transfer process which is present in almost any industrial and natural process. The vehicle drum brake systems can generate extremely high temperatures under high but short duration braking loads or under relatively light but continuous braking. For the proper conduct of the special vehicles mission in rough terrain, we are talking about, on one hand, the importance of the possibility of immobilization and retaining position and, on the other hand, during the braking process, the importance movement stability and reversibility or reversibility, to an encounter with an obstacle. Heat transfer processes influence the performance of the braking system. In the braking phase, kinetic energy transforms into thermal energy resulting in intense heating and high temperature states of analyzed vehicle wheels. In the present work a finite element model for the temperature distribution in a brake drum is developed, by employing commercial finite element software, ANSYS. These structural and thermal FEA models will simulate entire braking event. The heat generated during braking causes distortion which modifies thermoelastic contact pressure distribution drum-shoe interface. In order to capture the effect of heat, a transient thermal analysis is performed in order to predict the temperature distribution transitional brake components. Drum brakes are checked both mechanical and thermal. These tests aim to establish their sustainability in terms of wear and the variation coefficient of friction between the friction surfaces with increasing temperature. Modeling using simulation programs led eventually to the establishment of actual thermal load of the mechanism of brake components. It was drawn the efficiency characteristic by plotting the coefficient of effectiveness relative to the coefficient of friction shoe-drum. Thus induced

  9. Cholecystokinin: molecular cloning and immunohistochemical localization in the gastrointestinal tract of larval red drum, Sciaenops ocellatus (L.).

    PubMed

    Webb, Kenneth A; Khan, Izhar A; Nunez, B Scott; Rønnestad, Ivar; Holt, G Joan

    2010-03-01

    The current study sought to clarify the role of cholecystokinin (CCK) in the digestion of larval red drum (Sciaenops ocellatus) in order to better characterize the processes limiting the utilization of microparticulate diets at first feeding. The red drum CCK cDNA, isolated from adult anterior intestine and pyloric caeca, contains a 414 base pair (bp) open reading frame encoding a deduced amino acid sequence of 138 residues which is highly similar to preprocholecystokinin from other vertebrates. The mature CCK octapeptide has the same amino acid sequence as that found in mammals and in Atlantic herring (Clupea harengus). Tissue distribution analysis of adult and juvenile red drum using primers specific for red drum CCK mRNA revealed bright bands in samples from the brain, pyloric caeca, anterior intestine, and gonad with fainter bands seen in all other tissues. Immunohistochemical analysis of larval red drum showed that CCK-immunoreactive (CCK-IR) cells were present as early as 3 days post hatch (DPH) in some fish and were present in all fish by 6 DPH. CCK-IR cells were found in the anterior midgut in early larvae and had spread to the first bend of the gut by day 6. In older larvae (18+ DPH), CCK-IR cells were found in large numbers in the anterior intestine and in the developing pyloric caeca. The sequence and distribution of CCK mRNA along with the presence of CCK-IR cells in early red drum larvae suggest that CCK is present and may be capable of regulating pancreatic secretion in early red drum larvae.

  10. Ultrahigh carbon steels, Damascus steels, and superplasticity

    SciTech Connect

    Sherby, O.D.; Wadsworth, J.

    1997-04-01

    The processing properties of ultrahigh carbon steels (UHCSs) have been studied at Stanford University over the past twenty years. These studies have shown that such steels (1 to 2.1% C) can be made superplastic at elevated temperature and can have remarkable mechanical properties at room temperature. It was the investigation of these UHCSs that eventually brought us to study the myths, magic, and metallurgy of ancient Damascus steels, which in fact, were also ultrahigh carbon steels. These steels were made in India as castings, known as wootz, possibly as far back as the time of Alexander the Great. The best swords are believed to have been forged in Persia from Indian wootz. This paper centers on recent work on superplastic UHCSs and on their relation to Damascus steels. 32 refs., 6 figs.

  11. Corrosion of low-carbon steel under environmental conditions at Hanford: Two-year soil corrosion test results

    SciTech Connect

    Anantatmula, R.P.; Divine, J.R.

    1995-11-01

    At the Hanford Site, located in southeastern Washington state, nuclear production reactors were operated from 1944 to 1970. The handling and processing of radioactive nuclear fuels produced a large volume of low-level nuclear wastes, chemical wastes, and a combination of the two (mixed wastes). These materials have historically been packaged in US Department of Transportation (DOT) approved drums made from low-carbon steel, then handled in one of three ways: (A) Before 1970, the drums were buried in the dry desert soil. It was assumed that chemical and radionuclide mobility would be low and that the isolated, government-owned site would provide sufficient protection for employees and the public. (B) After 1970, the drums containing long-lived transuranic radionuclides were protected from premature failure by stacking them in an ordered array on an asphalt concrete pad in the bottom of a burial trench. The array was then covered with a large, 0.28-mm- (011-in.-) thick polyethylene tarp and the trench was backfilled with 1.3 m (4 ft) of soil cover. This burial method is referred to as soil-shielded burial . Other configurations were also employed but the soil-shielded burial method contains most of the transuranic drums. (C) Since 1987, US Department of Energy sites have complied with the Resource Conservation and Recovery Act of 1976 (RCRA) regulations. These regulations require mixed waste drums to be stored in RCRA compliant large metal sheds with provisions for monitoring. These sheds are provided with forced ventilation but are not heated or cooled.

  12. An analysis of thermionic space nuclear reactor power system: II. Merits of using safety drums for backup control

    SciTech Connect

    El-Genk, M.S.; Huimin Xue )

    1993-01-10

    An analysis is performed to investigate the merits of using the TOPAZ-II safety drums for a backup control to prevent a reactivity excursion, stabilize the reactor, and achieve steady-state power operation, following a severe hypothetical reactivity initiated accident (RIA). Such an RIA is assumed to occur during the system start-up in orbit due to a malfunction of the drive mechanism of the control drums, causing the nine drums to accidentally rotate the full 180[degree] outward. Results show that an immediate, inward rotation of the three safety drums to an angle of 80[degree] will shutdown the reactor, however, a delay time of 10 s will not only prevents a reactivity excursion, but also enables operating the reactor at a steady-state thermal power of about 33.3 kW (0.9 kW per TFE). Conversely, when the immediate rotation of the safety drums is to a larger angle of 100[degree], a steady-state operation at about 37 kW can be achieved, but a delay of 10 s causes a reactivity excursion and overheating of the TFEs. It is therefor concluded that, should the drive mechanism be modified to enable rotating the safety drums for TOPAZ-II reactor at variable speeds of and below 22.5[degree]/s, the three safety drums could be used successfully for a backup control, following an RIA. However, since the reactivity worth of the three safety drums is only $2.0, the maximum steady-state electric power achievable for the system is limited to approximately 0.25 kW, at which the fission power is about 37 kW and the emitter temperature is approximaely 1500 K. To alleviate such a limitation and enable operation at nominal design conditions (fission power of about 107 kW or a system's total electric power of 5.6 kW), the reactivity worth of the safety drums would have to be increased by at least $0.24.

  13. Habitat-related predation on juvenile wild-caught and hatchery-reared red drum Sciaenops ocellatus (Linnaeus).

    PubMed

    Stunz, G W.; Minello, T J.

    2001-05-31

    We examined the patterns of habitat-specific mortality for newly settled red drum (Sciaenops ocellatus) using an experimental mesocosm approach. Experiments were designed to analyze prey vulnerability and fish rearing-type (wild-caught or hatchery-reared) in estuarine habitats of varying structural complexity including marsh (Spartina alterniflora Loisel), oyster reef (Crassostrea virginica Gmelin), seagrass (Halodule wrightii Aschers), and nonvegetated sand bottom. We used two different predators, pinfish (Lagodon rhomboides Linnaeus) and spotted seatrout (Cynoscion nebulosus Cuvier). For both predators, vulnerability of wild-caught red drum was significantly lower in structurally complex habitats such as seagrass and oyster reef; the highest vulnerability was associated with the nonvegetated bottom. This habitat effect was not apparent for hatchery-reared prey. In trials using a combination of both rearing-types, there was no significant habitat effect on prey selection, but hatchery-reared red drum suffered higher overall mortality than wild-caught fish from pinfish predators. In these trials, spotted seatrout did not select for either prey type. Differences we observed in prey vulnerability were likely caused by behavioral differences between wild-caught and hatchery-reared red drum. Our results reinforce the conclusion that structural complexity in estuarine habitats increases survival of newly settled fishes. Our data also suggest that hatchery-reared red drum may be more vulnerable to predation than natural fishes, and that survival of stocked fish may be enhanced through habitat-related behavior modification.

  14. Avalanche dynamics of granular materials under the slumping regime in a rotating drum as revealed by speckle visibility spectroscopy.

    PubMed

    Yang, H; Li, R; Kong, P; Sun, Q C; Biggs, M J; Zivkovic, V

    2015-04-01

    We used speckle visibility spectroscopy to measure the time-resolved dynamcis of avalanching down the inclined surface of a granular material in a half-full rotating drum operating in the slumping regime. The distribution of the avalanche period, t(d), rest time between them, t(r), and peak particle velocity fluctuation, δv(p)(2), are all normally distributed. While the distributions of the two times at the top and bottom of the free surface are very similar, the particle velocity fluctuation is greater at the bottom of the free surface than at the top. The rest time is observed to be inversely related to the drum speed. Combining this with the relation of t(r) and the difference of the upper and lower angle of repose for the granular material, Δθ, we find that the latter decreases linearly with increasing rotational speed. We also observe that t(d) increases in a linear fashion with the drum speed. Using the relation of t(r) and the distance that particles have to move during an avalanche, we further find that a new scaling relation of the mean number of avalanches required to traverse the free surface with drum speed. We find that the slumping frequency increases with the rotating speed before becoming constant in the slumping-to-rolling transition region. Finally, we find that the average peak of the fluctuation speed of the avalanche, δv(p)(2), increases linearly with the drum speed.

  15. Avalanche dynamics of granular materials under the slumping regime in a rotating drum as revealed by speckle visibility spectroscopy

    NASA Astrophysics Data System (ADS)

    Yang, H.; Li, R.; Kong, P.; Sun, Q. C.; Biggs, M. J.; Zivkovic, V.

    2015-04-01

    We used speckle visibility spectroscopy to measure the time-resolved dynamcis of avalanching down the inclined surface of a granular material in a half-full rotating drum operating in the slumping regime. The distribution of the avalanche period, td, rest time between them, tr, and peak particle velocity fluctuation, δ vp2 , are all normally distributed. While the distributions of the two times at the top and bottom of the free surface are very similar, the particle velocity fluctuation is greater at the bottom of the free surface than at the top. The rest time is observed to be inversely related to the drum speed. Combining this with the relation of tr and the difference of the upper and lower angle of repose for the granular material, Δ θ , we find that the latter decreases linearly with increasing rotational speed. We also observe that td increases in a linear fashion with the drum speed. Using the relation of tr and the distance that particles have to move during an avalanche, we further find that a new scaling relation of the mean number of avalanches required to traverse the free surface with drum speed. We find that the slumping frequency increases with the rotating speed before becoming constant in the slumping-to-rolling transition region. Finally, we find that the average peak of the fluctuation speed of the avalanche, δ vp2 , increases linearly with the drum speed.

  16. Lawrence Livermore National Laboratory Experience Using 30-Gallon Drum Neutron Multiplicity Counter for Measuring Plutonium-Bearing Salts

    SciTech Connect

    Dearborn, D M; Keeton, S C

    2004-06-22

    Lawrence Livermore National Laboratory (LLNL) has been performing accountability measurements of plutonium (Pu) -bearing items with the 30-gallon drum neutron multiplicity counter (NMC) since August 1998. A previous paper focused on the LLNL experience with Pu-bearing oxide and metal items. This paper expands on the LLNL experience with Pu-bearing salts containing low masses of Pu. All Pu-bearing salts used in this study were measured using calorimetry and gamma isotopic analyses (Cal/Iso) as well as the 30-gallon drum NMC. The Cal/Iso values were treated as being the true measure of Pu content because of the inherent high accuracy of the Cal/Iso technique, even at low masses of Pu, when measured over a sufficient period of time. Unfortunately, the long time period required to achieve high accuracy from Cal/Iso can impact other required accountability measurements. The 30-gallon drum NMC is a much quicker system for making accountability measurements of a Pu-bearing salt and might be a desirable tradeoff. The accuracy of 30-gallon drum NMC measurements of Pu-bearing salts, relative to that of Cal/Iso, is presented in relation to the mass range and alpha associated with each item. Conclusions drawn from the use of the 30-gallon drum NMC for accountability measurements of salts are also included.

  17. The Impact of Group Drumming on Social-Emotional Behavior in Low-Income Children

    PubMed Central

    Ho, Ping; Tsao, Jennie C. I.; Bloch, Lian; Zeltzer, Lonnie K.

    2011-01-01

    Low-income youth experience social-emotional problems linked to chronic stress that are exacerbated by lack of access to care. Drumming is a non-verbal, universal activity that builds upon a collectivistic aspect of diverse cultures and does not bear the stigma of therapy. A pretest-post-test non-equivalent control group design was used to assess the effects of 12 weeks of school counselor-led drumming on social-emotional behavior in two fifth-grade intervention classrooms versus two standard education control classrooms. The weekly intervention integrated rhythmic and group counseling activities to build skills, such as emotion management, focus and listening. The Teacher's Report Form was used to assess each of 101 participants (n = 54 experimental, n = 47 control, 90% Latino, 53.5% female, mean age 10.5 years, range 10–12 years). There was 100% retention. ANOVA testing showed that intervention classrooms improved significantly compared to the control group in broad-band scales (total problems (P < .01), internalizing problems (P < .02)), narrow-band syndrome scales (withdrawn/depression (P < .02), attention problems (P < .01), inattention subscale (P < .001)), Diagnostic and Statistical Manual of Mental Disorders-oriented scales (anxiety problems (P < .01), attention deficit/hyperactivity problems (P < .01), inattention subscale (P < .001), oppositional defiant problems (P < .03)), and other scales (post-traumatic stress problems (P < .01), sluggish cognitive tempo (P < .001)). Participation in group drumming led to significant improvements in multiple domains of social-emotional behavior. This sustainable intervention can foster positive youth development and increase student-counselor interaction. These findings underscore the potential value of the arts as a therapeutic tool. PMID:21660091

  18. Fielded ATM network for the Air National Guard Global Yankee Fort Drum exercise

    NASA Astrophysics Data System (ADS)

    Kaminski, Robert L.; Hague, Daniel; Maciag, Chester

    1996-06-01

    This paper will review the deployment, demonstration, and test of an Asynchronous Transfer Mode (ATM) network to support the Air National Guard `Global Yankee' field exercise held at Fort Drum, New York. The network provided forty five (45) megabit per second (mbps) ATM connections between the Air Operations Center (AOC) and Forward Operating Location (FOL) located at Fort Drum, the State University of New York (SUNY) Health Science Center located in Syracuse, New York and Rome Laboratory located in Rome, New York. Connections were made with both fiber and free space equipment. The fiber connections used were part of the existing ATM New York Network (NYNet) between Rome Lab, SUNY Health Science Center and NYNEX Corporation. This network was extended to Watertown, New York by NYNEX to provide connectivity to Fort Drum. The free space links were provided by commercial DS-3 (45 mbps) radios, and 2 to 6 mbps Troposcatter Satellite Support Radios (TSSRs). This paper will also discuss significant digital Command, Control, Communications and Intelligence enhancements to the battlefield provided by the deployed ATM network. For example, videoconferencing and shared workspace capability was demonstrated over the AOC-to-FOL TSSR link, enabling remote intelligence briefings, pilot Battle Damage Assessment, and Search and Rescue coordination. Remote Medical Diagnostics videoconferencing with MRI high resolution digital imagery was demonstrated between the FOL, AOC, and SUNY Health Science Center. Finally, the network provided connectivity between the AOC and the Joint Surveillance System (JSS) radar's located at Griffiss Air Force BAse. The JSS data combined with the Rome Lab developed Radar Analysis Program provided AOC personnel with air picture areas of interest.

  19. Identification and molecular analysis of a ferritin subunit from red drum (Sciaenops ocellatus).

    PubMed

    Hu, Yong-hua; Zheng, Wen-jiang; Sun, Li

    2010-04-01

    Ferritin is a conserved iron binding protein existing ubiquitously in prokaryotes and eukaryotes. In this study, the gene encoding a ferritin M subunit homologue (SoFer1) was cloned from red drum (Sciaenops ocellatus) and analyzed at expression and functional levels. The open reading frame of SoFer1 is 531 bp and preceded by a 5'-untranslated region that contains a putative Iron Regulatory Element (IRE) preserved in many ferritins. The deduced amino acid sequence of SoFer1 possesses both the ferroxidase center of mammalian H ferritin and the iron nucleation site of mammalian L ferritin. Expression of SoFer1 was tissue specific and responded positively to experimental challenges with Gram-positive and Gram-negative fish pathogens. Treatment of red drum liver cells with iron, copper, and oxidant significantly upregulated the expression of SoFer1 in time-dependent manners. To further examine the potential role of SoFer1 in antioxidation, red drum liver cells transfected transiently with SoFer1 were prepared. Compared to control cells, SoFer1 transfectants exhibited reduced production of reactive oxygen species following H(2)O(2) challenge. Finally, to examine the iron binding potential of SoFer1, SoFer1 was expressed in and purified from Escherichia coli as a recombinant protein. Iron-chelating analysis showed that purified recombinant SoFer1 was capable of iron binding. Taken together, these results suggest that SoFer1 is likely to be a functional ferritin involved in iron sequestration, host immune defence against bacterial infection, and antioxidation.

  20. Osmoregulation and branchial plasticity after acute freshwater transfer in red drum, Sciaenops ocellatus.

    PubMed

    Watson, Caroline J; Nordi, Wiolene M; Esbaugh, Andrew J

    2014-12-01

    Red drum, Sciaenops ocellatus, is an estuarine-dependent fish species commonly found in the Gulf of Mexico and along the coast of the southeastern United States. This economically important species has demonstrated freshwater tolerance; however, the physiological mechanisms and costs related to freshwater exposure remain poorly understood. The current study therefore investigated the physiological response of red drum using an acute freshwater transfer protocol. Plasma osmolality, Cl⁻, Mg²⁺ and Ca²⁺ were all significantly reduced by 24h post-transfer; Cl⁻ and Mg²⁺ recovered to control levels by 7days post-transfer. No effect of transfer was observed on muscle water content; however, muscle Cl⁻ was significantly reduced. Interestingly, plasma and muscle Na⁺ content was unaffected by freshwater transfer. Intestinal fluid was absent by 24h post-transfer indicating cessation of drinking. Branchial gene expression analysis showed that both CFTR and NKCC1 exhibited significant down-regulation at 8 and 24h post-transfer, respectively, although transfer had no impact on NHE2, NHE3 or Na⁺, K⁺ ATPase (NKA) activity. These general findings are supported by immunohistochemical analysis, which revealed no apparent NKCC containing cells in the gills at 7days post transfer while NKA cells localization was unaffected. The results of the current study suggest that red drum can effectively regulate Na⁺ balance upon freshwater exposure using already present Na⁺ uptake pathways while also down-regulating ion excretion mechanisms.

  1. Dietary nucleotides influence immune responses and intestinal morphology of red drum Sciaenops ocellatus.

    PubMed

    Cheng, Zhenyan; Buentello, Alejandro; Gatlin, Delbert M

    2011-01-01

    Dietary nucleotides have been shown to benefit many physiological and nutritional functions in higher vertebrates and fish. Therefore, a 6-week feeding trial was conducted to evaluate the effects of graded levels of a commercial nucleotide product on growth performance, immune responses and intestinal morphology of juvenile red drum (initial average weight of 7.1g). The basal diet was formulated to contain 40% protein, 10% lipid and a digestible energy level of 3.5 kcal g(-1). Two levels of nucleotide (Ascogen P(®), 0.5% and 1% of diet) were added to the basal diet with menhaden fishmeal and menhaden oil adjusted to provide isonitrogenous and isolipidic diets. Nucleotide supplementation tended to improve weight gain and survival of red drum, but not at a significant level. Neutrophil oxidative radical anion production and serum lysozyme activity tended to be higher for fish fed diets supplemented with nucleotide, while extracellular superoxide anion production of head kidney macrophages from fish fed diets with 1% nucleotide was significantly (P<0.05) increased, although no significant differences were observed between fish fed 0.5% nucleotide diet and the basal diet. Nucleotide supplementation significantly (P<0.05) increased fold height in the proximal intestine, and enterocyte height in the pyloric caeca, proximal and distal enteric sections. A significantly (P<0.05) higher microvilli height was observed in all evaluated enteric sections of fish fed with diets supplemented with nucleotides. It is therefore possible to use dietary nucleotides supplementation to significantly enhance the intestinal structure of red drum. Likewise, nucleotides in the diet may improve some components of the non-specific immune response of this sciaenid fish.

  2. Dietary effects on thyroid hormones in the red drum, Sciaenops ocellatus.

    PubMed

    Mackenzie, D S; Moon, H Y; Gatlin, D M; Perez, L R

    1993-07-01

    Juvenile red drum (Sciaenops ocellatus) were cultured at 25°C on a variety of diets and blood sampled over eight weeks to examine the relationship between growth and plasma thyroid hormone levels. Maximum growth rates were achieved on formulated experimental diets and a simulated natural shrimp diet. Associated with these maximal rates was a significant increase in triidothyronine (T3), but no consistent change in thyroxine (T4). Reduced rations of diets resulted in low growth rates associated with significantly lowered levels of T3 but not T4. To determine whether weight gain could be increased by application of exogeneous hormone, diets were supplemented with T3 or T4 at 2, 10, and 50 mg hormone/kg diet. Significantly elevated T3 was induced by supplementation with 10 and 50 mg T3/kg diet, although there were no indications of an anabolic effect of T3 incorporation, and 50 mg T3/kg diet was in fact associated with decreased weight gain. Incorporation of T4 into diets had no effect on growth or T3, and had effects on T4 which were small and inconsistent, indicating that T4 may not be effectively absorbed from the gut. No difference was found in response to hormone feeding between low (6 ppt) or high (35 ppt) water salinity. T3 levels thus appear to closely parallel growth in fish on unsupplemented diets, whereas T4 which were small and manipulation. Supplementation with T3 is not an effective means of stimulating growth in red drum fed optimum diets. Whereas thyroid hormones may function to regulate intermediary metabolism in red drum, elevated endogenous thyroid hormone levels appear adequate to supply tissue needs during juvenile growth in culture.

  3. The impact of group drumming on social-emotional behavior in low-income children.

    PubMed

    Ho, Ping; Tsao, Jennie C I; Bloch, Lian; Zeltzer, Lonnie K

    2011-01-01

    Low-income youth experience social-emotional problems linked to chronic stress that are exacerbated by lack of access to care. Drumming is a non-verbal, universal activity that builds upon a collectivistic aspect of diverse cultures and does not bear the stigma of therapy. A pretest-post-test non-equivalent control group design was used to assess the effects of 12 weeks of school counselor-led drumming on social-emotional behavior in two fifth-grade intervention classrooms versus two standard education control classrooms. The weekly intervention integrated rhythmic and group counseling activities to build skills, such as emotion management, focus and listening. The Teacher's Report Form was used to assess each of 101 participants (n = 54 experimental, n = 47 control, 90% Latino, 53.5% female, mean age 10.5 years, range 10-12 years). There was 100% retention. ANOVA testing showed that intervention classrooms improved significantly compared to the control group in broad-band scales (total problems (P < .01), internalizing problems (P < .02)), narrow-band syndrome scales (withdrawn/depression (P < .02), attention problems (P < .01), inattention subscale (P < .001)), Diagnostic and Statistical Manual of Mental Disorders-oriented scales (anxiety problems (P < .01), attention deficit/hyperactivity problems (P < .01), inattention subscale (P < .001), oppositional defiant problems (P < .03)), and other scales (post-traumatic stress problems (P < .01), sluggish cognitive tempo (P < .001)). Participation in group drumming led to significant improvements in multiple domains of social-emotional behavior. This sustainable intervention can foster positive youth development and increase student-counselor interaction. These findings underscore the potential value of the arts as a therapeutic tool.

  4. Evaluation of Ocimum americanum essential oil as an additive in red drum (Sciaenops ocellatus) diets.

    PubMed

    Sutili, Fernando J; Velasquez, Alejandro; Pinheiro, Carlos G; Heinzmann, Berta M; Gatlin, Delbert M; Baldisserotto, Bernardo

    2016-09-01

    This study evaluated productive parameters, whole-body composition, non-specific immune responses and pH and microbiota of digestive tract contents of red drum (Sciaenops ocellatus) fed diets supplemented with Ocimum americanum essential oil (OAEO) (0 - control, 0.25, 0.5, 1.0 and 2.0 g/kg diet). After 7 weeks no significant differences in productive parameters and whole-body composition were observed. Plasma and intestinal lysozyme measurements and pH of the stomach and intestine (6 h after feeding) did not show significant differences among groups. Intestinal microbial community in fish fed the basal and OAEO diets (all concentrations) were identical. However, red drum fed the diet with OAEO at 1.0 g/kg had significantly increased intraperitoneal fat deposition and stomach pH (2 h after feeding) and decreased superoxide ion production (NBT-test) compared to the control group. Hemolytic activity of the complement system increased in fish fed diets containing OAEO. Red blood cells from fish fed the lowest OAEO concentration (0.25 g/kg) showed significant lower fragility in erythrocyte osmotic fragility assay, but fish fed 0.5 and 1.0 g/kg showed significant higher erythrocyte fragility. Lysozyme measurement in the supernatant of stomach content was significantly higher in fish fed the diet supplemented at 0.5 g/kg. Based on these various results, OAEO at different supplementation levels did not influence growth performance and intestinal microbial community; however, the EO added to the diet showed effects on immunological responses of red drum.

  5. Evidence for metal poisoning in acute deaths of large red drum (Scianeops ocellata)

    SciTech Connect

    Cardeihac, P.T.; Simpson, C.F.; White, F.H.; Thompson, N.P.; Carr, W.E.

    1981-12-01

    Two of the approximately 100 large, mature, red drum found dead or dying in Florida's Indian River and Mosquito Lagoon were examined. Determinations were made of serum electrolyte concentrations, total proteins, albumins, globulins, creatinine values, and enzyme activity. Concentrations of copper, zinc, arsenic, chromium, cadmium, mercury, lead, and selenium were determined by atomic aborption. The outstanding histological lesions were found in the gills of a moribund specimen. Results indicate that the acute episode was triggered by ingestion of copper, zinc, and arsenic. However, cadmium, mercury and chromium may have been contributory by binding with metallothionein and thus lowering tolerance to metal poisoning. (JMT)

  6. Radionuclide measurement proficiency testing for SNAP using NPL waste drum standards.

    PubMed

    Miller, T J

    2010-12-01

    AWE has participated in two rounds of radionuclide measurement proficiency testing using 200 l waste drum standards prepared by the National Physical Laboratory (NPL). The results achieved, using the SNAP (spectral non-destructive assay platform) system, were generally within a few per cent of the true activities and gave confidence in the ability to allocate wastes to the correct categories in accordance with national legislation. This is important for reasons of public safety and also for minimisation of the amount of RSA (Radioactive Substances Act) Exempt material categorised as LLW (low level waste) as the UK's LLW storage capacity diminishes.

  7. DRUMS: Disk Repository with Update Management and Select option for high throughput sequencing data

    PubMed Central

    2014-01-01

    Background New technologies for analyzing biological samples, like next generation sequencing, are producing a growing amount of data together with quality scores. Moreover, software tools (e.g., for mapping sequence reads), calculating transcription factor binding probabilities, estimating epigenetic modification enriched regions or determining single nucleotide polymorphism increase this amount of position-specific DNA-related data even further. Hence, requesting data becomes challenging and expensive and is often implemented using specialised hardware. In addition, picking specific data as fast as possible becomes increasingly important in many fields of science. The general problem of handling big data sets was addressed by developing specialized databases like HBase, HyperTable or Cassandra. However, these database solutions require also specialized or distributed hardware leading to expensive investments. To the best of our knowledge, there is no database capable of (i) storing billions of position-specific DNA-related records, (ii) performing fast and resource saving requests, and (iii) running on a single standard computer hardware. Results Here, we present DRUMS (Disk Repository with Update Management and Select option), satisfying demands (i)-(iii). It tackles the weaknesses of traditional databases while handling position-specific DNA-related data in an efficient manner. DRUMS is capable of storing up to billions of records. Moreover, it focuses on optimizing relating single lookups as range request, which are needed permanently for computations in bioinformatics. To validate the power of DRUMS, we compare it to the widely used MySQL database. The test setting considers two biological data sets. We use standard desktop hardware as test environment. Conclusions DRUMS outperforms MySQL in writing and reading records by a factor of two up to a factor of 10000. Furthermore, it can work with significantly larger data sets. Our work focuses on mid-sized data

  8. Drum-Assisted Recovery Therapy for Native Americans (DARTNA): results from a pretest and focus groups.

    PubMed

    Dickerson, Daniel L; Venner, Kamilla L; Duran, Bonnie; Annon, Jeffrey J; Hale, Benjamin; Funmaker, George

    2014-01-01

    Drum-Assisted Recovery Therapy for Native Americans (DARTNA) is a substance abuse treatment intervention for American Indians/Alaska Natives (AI/ANs). This article provides results from 1) an initial pretest of DARTNA provided to 10 AI/AN patients with histories of substance use disorders, and 2) three subsequent focus groups conducted among AI/AN DARTNA pretest participants, substance abuse treatment providers, and the DARTNA Community Advisory Board. These research activities were conducted to finalize the DARTNA treatment manual; participants also provided helpful feedback which will assist toward this goal. Results suggest that DARTNA may be beneficial for AI/ANs with substance use problems.

  9. Geophysical logging at the Cristex Drum National Priorities List Superfund Site near Oxford, North Carolina

    USGS Publications Warehouse

    Antolino, Dominick J.

    2017-01-01

    The collection of borehole geophysical logs data was conducted by the U.S. Geological Survey South Atlantic Water Science Center in the vicinity of the Cristex Drum National Priorities List Superfund Site near Oxford, North Carolina, during January through March 2016. In an effort to assist the U.S. Environmental Protection Agency in the development of a conceptual groundwater model for the assessment of current contaminant distribution and future migration of contaminants, borehole geophysical log and image data collection, which included the delineation of more than 150 subsurface features (primarily fracture orientations) in 3 open borehole wells.

  10. Electrically integrated SU-8 clamped graphene drum resonators for strain engineering

    NASA Astrophysics Data System (ADS)

    Lee, Sunwoo; Chen, Changyao; Deshpande, Vikram V.; Lee, Gwan-Hyoung; Lee, Ilkyu; Lekas, Michael; Gondarenko, Alexander; Yu, Young-Jun; Shepard, Kenneth; Kim, Philip; Hone, James

    2013-04-01

    Graphene mechanical resonators are the ultimate two-dimensional nanoelectromechanical systems (NEMS) with applications in sensing and signal processing. While initial devices have shown promising results, an ideal graphene NEMS resonator should be strain engineered, clamped at the edge without trapping gas underneath, and electrically integratable. In this Letter, we demonstrate fabrication and direct electrical measurement of circular SU-8 polymer-clamped chemical vapor deposition graphene drum resonators. The clamping increases device yield and responsivity, while providing a cleaner resonance spectrum from eliminated edge modes. Furthermore, the clamping induces a large strain in the resonator, increasing its resonant frequency.

  11. Euler-like modelling of dense granular flows: application to a rotating drum

    NASA Astrophysics Data System (ADS)

    Bonamy, D.; Chavanis, P.-H.; Cortet, P.-P.; Daviaud, F.; Dubrulle, B.; Renouf, M.

    2009-04-01

    General conservation equations are derived for 2D dense granular flows from the Euler equation within the Boussinesq approximation. In steady flows, the 2D fields of granular temperature, vorticity and stream function are shown to be encoded in two scalar functions only. We checked such prediction on steady surface flows in a rotating drum simulated through the Non-Smooth Contact Dynamics method even though granular flows are dissipative and therefore not necessarily compatible with Euler equation. Finally, we briefly discuss some possible ways to predict theoretically these two functions using statistical mechanics.

  12. ARROW-PAK Macroencapsulation. Innovative Technology Summary Report

    SciTech Connect

    2002-04-01

    An ARROW-PAK is a high density polyethylene (HDPE) tube, about 21 feet long and 30 inches wide. Each ARROW-PAK can hold the equivalent of 21 55-gallon drums of mixed waste debris. Each tube is fused to HDPE endcaps using localized heating and high pressure contact. The sleeves and encaps form a tube for macroencapsulating mixed waste debris. The ARROW-PAK may achieve a mixed waste debris volume one-fourth that of the conventional macroencapsulation approach. The mixed waste debris is loaded into 55-gallon drums. Once filled a 'supercompactor' crushes the drums into 12-inch thick pucks. Three pucks can be loaded into a standard 85-gallon metal drum known as an 'overpack'. Seven overpacks fit into each ARROW-PAK.

  13. Superfund Record of Decision (EPA Region 2): Tabernacle Drum Dump, New Jersey (first remedial action), June 1988. Final report

    SciTech Connect

    Not Available

    1988-06-30

    The Tabernacle Drum Dump site is a one-acre facility located in Tabernacle Township, Burlington County, New Jersey. Drum-disposal activities, which resulted in contamination by hazardous substances, occurred on a 2,000 sq ft area portion of the site. During 1976 and 1977, the Atlantic Disposal Services (ADS), disposed of approximately 200 fifty-five gallon drums, twenty gallon containers, and five gallon paint cans, which were stored at the site from 1977 to 1984. Deterioration and leakage of some containers resulted in visible soil contamination and ultimately ground-water contamination. The principal threat posed at the site is potential ingestion of ground water including VOCs. Remedial actions for this site are discussed.

  14. Welding Rustproof Steels

    NASA Technical Reports Server (NTRS)

    Hoffmann, W

    1929-01-01

    The following experimental results will perhaps increase the knowledge of the process of welding rustproof steels. The experiments were made with two chrome-steel sheets and with two chrome-steel-nickel sheets having the composition shown in Table I.

  15. Comminuting irradiated ferritic steel

    DOEpatents

    Bauer, Roger E.; Straalsund, Jerry L.; Chin, Bryan A.

    1985-01-01

    Disclosed is a method of comminuting irradiated ferritic steel by placing the steel in a solution of a compound selected from the group consisting of sulfamic acid, bisulfate, and mixtures thereof. The ferritic steel is used as cladding on nuclear fuel rods or other irradiated components.

  16. In vitro effects of plant essential oils on non-specific immune parameters of red drum, Sciaenops ocellatus L.

    PubMed

    Sutili, F J; Gatlin, D M; Rossi, W; Heinzmann, B M; Baldisserotto, B

    2016-12-01

    Phytochemicals such as plant essential oils (EOs) have been reported to favour various activities in the innate immune system of fish. Thus, the aim of this study was to verify the in vitro effect of three different plant EOs (Ocimum americanum, Cymbopogon flexuosus and Melaleuca alternifolia) on non-specific immune parameters and erythrocyte osmotic fragility of red drum, Sciaenops ocellatus. Concentrations of each plant EO evaluated in preparations of head-kidney macrophages, blood leucocytes and blood plasma were as follows: 0.0 (control), 1.0, 2.0, 4.0, 8.0, and 16.0 μg/ml. Red drum head-kidney macrophages significantly increased extracellular superoxide anion production when exposed (20 h) to O. americanum EO (1.0-8.0 μg/ml) and C. flexuosus EO (2.0 and 4.0 μg/ml). The respiratory burst of blood leucocytes (NBT test) significantly increased in all concentrations when compared to the respective control group, for all EOs. At the highest concentration (16.0 μg/ml), C. flexuosus EO significantly inhibited the haemolytic activity of complement system in red drum blood after 1 h exposure. None of the tested concentrations significantly altered plasma lysozyme activity or erythrocyte osmotic fragility after exposing (1 h) red drum whole blood to each EO. This study demonstrated that these plant EOs are capable of triggering superoxide anion production in red drum leucocytes (head-kidney macrophages and/or blood leucocytes). In vivo studies are warranted to address their potential as immunostimulants in the diet of red drum and other aquacultured species.

  17. Intelligent Mobile Sensor System for drum inspection and monitoring -- Volume 1. Final report, October 1, 1993--April 22, 1995

    SciTech Connect

    1995-12-31

    The objective of the Intelligent Mobile Sensor System (IMSS) project is to develop an operational system for monitoring and inspection activities for waste storage facility operations at several DOE sites. Specifically, the product of this effort is a robotic device with enhanced intelligence and maneuverability capable of conducting routine inspection of stored waste drums. The device is capable of operating in the narrow free aisle space between rows of stacked drums. The system has an integrated sensor suite for problem-drum detection, and is linked to a site database both for inspection planning and for data correlation, updating, and report generation. The system is capable of departing on an assigned mission, collecting required data, recording which portions of its mission had to be aborted or modified due to environmental constraints, and reporting back when the mission is complete. Successful identification of more than 96% of drum defects has been demonstrated in a high fidelity waste storage facility mockup. Identified anomalies included rust spots, rust streaks, areas of corrosion, dents, and tilted drums. All drums were positively identified and correlated with the site database. This development effort is separated into three phases of which phase two is now complete. The first phase demonstrated an integrated system (maturity level IVa) for monitoring and inspection activities for waste storage facility operations. The second phase demonstrated a prototype system appropriate for operational use in an actual storage facility. The prototype provides an integrated design that considers operational requirements, hardware costs, maintenance, safety, and robustness. The final phase will demonstrate commercial viability using the prototype vehicle in a pilot waste operations and inspection project. This report summarizes the design and evaluation of the new IMSS Phase 2 system and vehicle.

  18. Feasibility study of 235U and 239Pu characterization in radioactive waste drums using neutron-induced fission delayed gamma rays

    NASA Astrophysics Data System (ADS)

    Nicol, T.; Pérot, B.; Carasco, C.; Brackx, E.; Mariani, A.; Passard, C.; Mauerhofer, E.; Collot, J.

    2016-10-01

    This paper reports a feasibility study of 235U and 239Pu characterization in 225 L bituminized waste drums or 200 L concrete waste drums, by detecting delayed fission gamma rays between the pulses of a deuterium-tritium neutron generator. The delayed gamma yields were first measured with bare samples of 235U and 239Pu in REGAIN, a facility dedicated to the assay of 118 L waste drums by Prompt Gamma Neutron Activation Analysis (PGNAA) at CEA Cadarache, France. Detectability in the waste drums is then assessed using the MCNPX model of MEDINA (Multi Element Detection based on Instrumental Neutron Activation), another PGNAA cell dedicated to 200 L drums at FZJ, Germany. For the bituminized waste drum, performances are severely hampered by the high gamma background due to 137Cs, which requires the use of collimator and shield to avoid electronics saturation, these elements being very penalizing for the detection of the weak delayed gamma signal. However, for lower activity concrete drums, detection limits range from 10 to 290 g of 235U or 239Pu, depending on the delayed gamma rays of interest. These detection limits have been determined by using MCNPX to calculate the delayed gamma useful signal, and by measuring the experimental gamma background in MEDINA with a 200 L concrete drum mock-up. The performances could be significantly improved by using a higher interrogating neutron emission and an optimized experimental setup, which would allow characterizing nuclear materials in a wide range of low and medium activity waste packages.

  19. Optimization of feed rates and rearing densities for production of advanced juvenile red drum in recirculating aquaculture systems for stock enhancement

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Saltwater sportfishing for red drum, Sciaenops ocellatus, is of immense importance to the recreational saltwater fishing industry from the Gulf of Mexico coastal states through Florida and along the Atlantic seaboard to Maryland and Delaware. Red drum are the second most sought after sportfish in th...

  20. Manufacture of PCDE Prepolymer

    DTIC Science & Technology

    1977-10-01

    gallon polyethylene drum where the aqueous phase and the product-bearing organic phase separate. The sulfuric acid stream is added for two purposes. First...storage. Aqueous waste from the 55-gallon product drums and from the top of the extraction columns is collected in a 350-gallon polyethylene tank. The waste...susceptible to corrosion because of the aqueous media in the reactor and the fact that for every mole of DFU formed two moles of HF are also formed. Equipment

  1. Final Environmental Assessment: For Okaloosa County Wastewater Treatment Facility Eglin Air Force Base, Florida

    DTIC Science & Technology

    2004-04-01

    oxygen levels and result in a detrimental condition known as eutrophication . Other potential impacts to surface waters include construction impacts...waste holding area (Law Engineering, 2001). The facility stored oil in 55-gallon waste oil drums. The waste oil drums were placed on concrete...County Water and Sewer in December 1999, which revealed no visual indication of oil spills on the ground surface at the previous CRD land area (Law

  2. Fault Diagnosis of Demountable Disk-Drum Aero-Engine Rotor Using Customized Multiwavelet Method

    PubMed Central

    Chen, Jinglong; Wang, Yu; He, Zhengjia; Wang, Xiaodong

    2015-01-01

    The demountable disk-drum aero-engine rotor is an important piece of equipment that greatly impacts the safe operation of aircraft. However, assembly looseness or crack fault has led to several unscheduled breakdowns and serious accidents. Thus, condition monitoring and fault diagnosis technique are required for identifying abnormal conditions. Customized ensemble multiwavelet method for aero-engine rotor condition identification, using measured vibration data, is developed in this paper. First, customized multiwavelet basis function with strong adaptivity is constructed via symmetric multiwavelet lifting scheme. Then vibration signal is processed by customized ensemble multiwavelet transform. Next, normalized information entropy of multiwavelet decomposition coefficients is computed to directly reflect and evaluate the condition. The proposed approach is first applied to fault detection of an experimental aero-engine rotor. Finally, the proposed approach is used in an engineering application, where it successfully identified the crack fault of a demountable disk-drum aero-engine rotor. The results show that the proposed method possesses excellent performance in fault detection of aero-engine rotor. Moreover, the robustness of the multiwavelet method against noise is also tested and verified by simulation and field experiments. PMID:26512668

  3. "Are you going to be Miss (or Mr) Africa?" Contesting masculinity in Drum magazine.

    PubMed

    Clowes, L

    2001-01-01

    Drum magazine was first published in March 1951. Like other magazines, it both reflected and shaped the society from which its audience emerged. During 1951, its audience, mainly urban black readers, was able to push the publication away from its original rural focus towards an urban emphasis. Town living, however, meant different things to different people. Thus, while readers were successful in shifting the focus of the magazine, they were less successful in influencing the way the publication presented urban life. This paper explores the struggle between readers, journalists and editors over the Miss Africa beauty contest announced at the beginning of 1952. Although the magazine reluctantly admitted men to the contest, it discriminated against male entrants in a variety of ways over the course of the year, and subsequent competitions barred male contestants entirely. Despite opposition from male readers who wished to be considered beautiful, the men of Drum were largely successful in asserting their own deeply gendered cultural vision of urban life.

  4. Effects of dietary thyroid hormones on the red drum (Sciaenops ocellatus).

    PubMed

    Moon, H L; Mackenzie, D S; Gatlin, D M

    1994-01-01

    Four separate 8-week feeding trials were conducted to assess the effects of supplementing semipurified diets with either triiodothyronine (T3) or thyroxine (T4) at 0, 2, 10, and 50 mg/kg on growth and body composition of juvenile red drum (Sciaenops ocellatus) held in artificial brackish water (6‰) and artificial seawater (32‰). At both levels of salinity, increasing doses of T3 resulted in fish with reduced weight gain, feed efficiency, condition factor (weight × 100/length(3)), and muscle ratio (muscle weight × 100/body weight), as well as a lighter body color. Significant (p < 0.05) effects of T3 on the proximate composition of whole body, liver, and muscle were variable, generally reflecting decreased lipid and protein storage in liver and muscle, respectively. The two highest doses of T3 given to seawater adapted fish increased survival. Dietary T4 supplementation had no distinctive effects on appearance, growth or proximate body composition. These results indicate that whereas T3 may function to regulate protein and lipid metabolism in red drum, dietary supplementation with T3 leads to a hyperthyroidism-induced catabolic state. The elevated endogenous thyroid hormone levels found in fish fed optimal diets may thus adequately supply tissue needs during juvenile growth.

  5. Fault Diagnosis of Demountable Disk-Drum Aero-Engine Rotor Using Customized Multiwavelet Method.

    PubMed

    Chen, Jinglong; Wang, Yu; He, Zhengjia; Wang, Xiaodong

    2015-10-23

    The demountable disk-drum aero-engine rotor is an important piece of equipment that greatly impacts the safe operation of aircraft. However, assembly looseness or crack fault has led to several unscheduled breakdowns and serious accidents. Thus, condition monitoring and fault diagnosis technique are required for identifying abnormal conditions. Customized ensemble multiwavelet method for aero-engine rotor condition identification, using measured vibration data, is developed in this paper. First, customized multiwavelet basis function with strong adaptivity is constructed via symmetric multiwavelet lifting scheme. Then vibration signal is processed by customized ensemble multiwavelet transform. Next, normalized information entropy of multiwavelet decomposition coefficients is computed to directly reflect and evaluate the condition. The proposed approach is first applied to fault detection of an experimental aero-engine rotor. Finally, the proposed approach is used in an engineering application, where it successfully identified the crack fault of a demountable disk-drum aero-engine rotor. The results show that the proposed method possesses excellent performance in fault detection of aero-engine rotor. Moreover, the robustness of the multiwavelet method against noise is also tested and verified by simulation and field experiments.

  6. Investigation of drum pressurization incident in the 331 Building, Room 175 on January 10, 1995

    SciTech Connect

    Pollari, R.A.

    1995-02-01

    On January 10, 1995, a pressurized drum incident occurred at the 331 Building, Room 175. On January 12, 1995, the Manager of the Life Sciences Center appointed members to an Investigation Board to investigate the incident (see Exhibit A). This incident was initially categorized as an Off-Normal Occurrence, but was later elevated to an Unusual Occurrence by the Occurrence Classifier. The scope of this investigation was to employ a formal method of root cause analysis, identify the methodology, and report the results of the analysis, fully explaining the technical elements of the causal sequence along with a description of the barriers that should have or could have prevented the occurrence. During the course of the investigation, the scene of the event was not accessible. Therefore, the investigation relied primarily on testimony from staff members directly involved and their management. In addition, other outside professionals were also consulted. The Investigation Board visited the previous location of the drum, 331A Building, Room 9; Room 173, which fronts room 175, was also visited. The Investigation Board reviewed selected documents, which are also listed.

  7. IMPROVING THERMAL PERFORMANCE OF RADIOACTIVE MATERIAL DRUM TYPEPACKAGES BY USING HEAT PIPES

    SciTech Connect

    Gupta, N

    2007-03-06

    This paper presents a feasibility study to improve thermal loading of existing radioactive material packages by using heat pipes. The concept could be used to channel heat in certain directions and dissipate to the environment. The concept is applied to a drum type package because the drum type packages are stored and transported in an upright position. This orientation is suitable for heat pipe operation that could facilitate the heat pipe implementation in the existing well proven package designs or in new designs where thermal loading is high. In this position, heat pipes utilize gravity very effectively to enhance heat flow in the upward direction Heat pipes have extremely high effective thermal conductivity that is several magnitudes higher than the most heat conducting metals. In addition, heat pipes are highly unidirectional so that the effective conductivity for heat transfer in the reverse direction is greatly reduced. The concept is applied to the 9977 package that is currently going through the DOE certification review. The paper presents computer simulations using typical off-the-shelf heat pipe available configurations and performance data for the 9977 package. A path forward is outlined for implementing the concepts for further study and prototype testing.

  8. Analytical Chemistry and Materials Characterization Results for Debris Recovered from Nitrate Salt Waste Drum S855793

    SciTech Connect

    Martinez, Patrick Thomas; Chamberlin, Rebecca M.; Schwartz, Daniel S.; Worley, Christopher Gordon; Garduno, Katherine; Lujan, Elmer J. W.; Borrego, Andres Patricio; Castro, Alonso; Colletti, Lisa Michelle; Fulwyler, James Brent; Holland, Charlotte S.; Keller, Russell C.; Klundt, Dylan James; Martinez, Alexander; Martin, Frances Louise; Montoya, Dennis Patrick; Myers, Steven Charles; Porterfield, Donivan R.; Schake, Ann Rene; Schappert, Michael Francis; Soderberg, Constance B.; Spencer, Khalil J.; Stanley, Floyd E.; Thomas, Mariam R.; Townsend, Lisa Ellen; Xu, Ning

    2015-09-16

    Solid debris was recovered from the previously-emptied nitrate salt waste drum S855793. The bulk sample was nondestructively assayed for radionuclides in its as-received condition. Three monoliths were selected for further characterization. Two of the monoliths, designated Specimen 1 and 3, consisted primarily of sodium nitrate and lead nitrate, with smaller amounts of lead nitrate oxalate and lead oxide by powder x-ray diffraction. The third monolith, Specimen 2, had a complex composition; lead carbonate was identified as the predominant component, and smaller amounts of nitrate, nitrite and carbonate salts of lead, magnesium and sodium were also identified. Microfocused x-ray fluorescence (MXRF) mapping showed that lead was ubiquitous throughout the cross-sections of Specimens 1 and 2, while heteroelements such as potassium, calcium, chromium, iron, and nickel were found in localized deposits. MXRF examination and destructive analysis of fragments of Specimen 3 showed elevated concentrations of iron, which were broadly distributed through the sample. With the exception of its high iron content and low carbon content, the chemical composition of Specimen 3 was within the ranges of values previously observed in four other nitrate salt samples recovered from emptied waste drums.

  9. Allozyme frequencies of freshwater drum and their association with water quality in the Ohio River

    SciTech Connect

    Gillespie, R.B.

    1994-12-31

    Frequencies of electrophoretically-detected allele variants (allozymes) in aquatic populations may act as biological indicators of contaminant-induced impacts. Selection against ``pollution-sensitive`` individuals ay cause significant changes in allele and genotype frequencies of allozymes in populations exposed to environmental contaminants. Freshwater drum (Aplodinotus grunniens) were collected from three sites in the Ohio River that varied in water quality. Cellulose acetate electrophoresis resolved three variable enzymes in freshwater drum. Frequencies of multiple-locus allozyme genotypes differed significantly among sites and were associated with differences in water quality in the Ohio River. The variation of multiple locus genotypes was positively associated with water quality. If allozyme variation is reliable, then fish populations exposed to poorer water quality may have less genetic variation than those inhabiting sites with better water quality. Associations between allozyme frequencies nd exposure to contaminants indicate that allozyme frequencies may be sensitive indicators for detecting contaminant-induced impacts in aquatic populations. If allozyme frequencies are reliable, monitoring them would allow researchers to assess genetic variability in aquatic populations where contaminated-induced effects are suspected.

  10. The steel scrap age.

    PubMed

    Pauliuk, Stefan; Milford, Rachel L; Müller, Daniel B; Allwood, Julian M

    2013-04-02

    Steel production accounts for 25% of industrial carbon emissions. Long-term forecasts of steel demand and scrap supply are needed to develop strategies for how the steel industry could respond to industrialization and urbanization in the developing world while simultaneously reducing its environmental impact, and in particular, its carbon footprint. We developed a dynamic stock model to estimate future final demand for steel and the available scrap for 10 world regions. Based on evidence from developed countries, we assumed that per capita in-use stocks will saturate eventually. We determined the response of the entire steel cycle to stock saturation, in particular the future split between primary and secondary steel production. During the 21st century, steel demand may peak in the developed world, China, the Middle East, Latin America, and India. As China completes its industrialization, global primary steel production may peak between 2020 and 2030 and decline thereafter. We developed a capacity model to show how extensive trade of finished steel could prolong the lifetime of the Chinese steelmaking assets. Secondary steel production will more than double by 2050, and it may surpass primary production between 2050 and 2060: the late 21st century can become the steel scrap age.

  11. Methods of forming steel

    DOEpatents

    Branagan, Daniel J.; Burch, Joseph V.

    2001-01-01

    In one aspect, the invention encompasses a method of forming a steel. A metallic glass is formed and at least a portion of the glass is converted to a crystalline steel material having a nanocrystalline scale grain size. In another aspect, the invention encompasses another method of forming a steel. A molten alloy is formed and cooled the alloy at a rate which forms a metallic glass. The metallic glass is devitrified to convert the glass to a crystalline steel material having a nanocrystalline scale grain size. In yet another aspect, the invention encompasses another method of forming a steel. A first metallic glass steel substrate is provided, and a molten alloy is formed over the first metallic glass steel substrate to heat and devitrify at least some of the underlying metallic glass of the substrate.

  12. Effects of light on plasma somatolactin levels in red drum (Sciaenops ocellatus).

    PubMed

    Zhu, Y; Thomas, P

    1998-07-01

    The effects of illumination on circulating somatolactin (SL) levels were studied in red drum sampled at various times during a 24-h light-dark cycle (l2L:l2D) and during a 24-h period of constant light. Plasma SL concentrations were low in red drum sampled during the light phase (0.6 +/- 0.05-1.1 +/- 0.2 ng/ml). The levels were significantly elevated during the early-dark phase (5.8 +/- 1.0 ng/ml) and declined during the late-dark phase (0.39 +/- 0.05 ng/ml). In contrast, plasma SL levels remained low. (0.4 +/- 0.1-1.3 +/- 0.4 ng/ml) in fish sampled through a 24-h constant light period following a 1-week exposure to the light-dark cycle. Circulating SL levels were also significantly elevated during the early-dark phase in fish maintained under a reversed light-dark cycle. The role of the eyes in mediation the SL response to light was evaluated by comparing circulating SL levels in optic-tract sectioned and enucleated fish with those of intact (control) fish. Plasma SL concentrations were significantly higher in optic-tract sectioned and enucleated fish (6.5 +/- 0.9-13.8 +/- 1.5 ng/ml) than in control fish (0.6 +/- 0.05-3.9 +/- 0.7 ng/ml) during both the early-dark phase and the early-light phase of the 24-h light-dark cycle. The absence of significant changes in plasma SL levels between the light and dark phases in optic-tract sectioned and enucleated fish appears to be due to a loss of light perception in these fish. Moreover, intact and sham-operated red drum maintained in constant darkness had dramatically increased plasma SL levels (18.8 +/- 2.0-24.8 +/- 1.8 ng/ml). The present results are consistent with our earlier findings that plasma SL levels are elevated in fish kept in constant darkness and in a dark-background tank (reduction in overall light levels) during the light phase. Taken together, these results suggest that plasma SL levels are elevated in red drum in the absence of light and in response to low illumination. Interestingly, the integument of the

  13. Criticality Safety Evaluations on the Use of 200-gram Pu Mass Limit for RHWM Waste Storage Operations

    SciTech Connect

    Chou, P

    2011-12-14

    This work establishes the criticality safety technical basis to increase the fissile mass limit from 120 grams to 200 grams for Type A 55-gallon drums and their equivalents. Current RHWM fissile mass limit is 120 grams Pu for Type A 55-gallon containers and their equivalent. In order to increase the Type A 55-gallon drum limit to 200 grams, a few additional criticality safety control requirements are needed on moderators, reflectors, and array controls to ensure that the 200-gram Pu drums remain criticality safe with inadvertent criticality remains incredible. The purpose of this work is to analyze the use of 200-gram Pu drum mass limit for waste storage operations in Radioactive and Hazardous Waste Management (RHWM) Facilities. In this evaluation, the criticality safety controls associated with the 200-gram Pu drums are established for the RHWM waste storage operations. With the implementation of these criticality safety controls, the 200-gram Pu waste drum storage operations are demonstrated to be criticality safe and meet the double-contingency-principle requirement per DOE O 420.1.

  14. 40 CFR 265.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    .... (e) Reactive waste, other than cyanide- or sulfide-bearing waste as defined in § 261.23(a)(5) of this... hazardous waste in overpacked drums (lab packs). 265.316 Section 265.316 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) INTERIM STATUS STANDARDS FOR OWNERS...

  15. 40 CFR 264.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... defined in § 260.10 of this chapter, must not be placed in the same outside container. (e) Reactive wastes... hazardous waste in overpacked drums (lab packs). 264.316 Section 264.316 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR OWNERS AND OPERATORS...

  16. Effects of the prebiotics GroBiotic-A and inulin on the intestinal microbiota of red drum, Sciaenops ocellatus

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Two separate feeding trials examined the effects of dietary supplementation of the prebiotics GroBiotic®-A and inulin on growth performance and gastrointestinal tract microbiota of the red drum Sciaenops ocellatus. In the first feeding trial, fishmeal-based diets without prebiotics or supplemented ...

  17. 7 CFR 160.201 - Fees generally for field inspection and certification of naval stores and drum containers of rosin.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Fees generally for field inspection and certification of naval stores and drum containers of rosin. 160.201 Section 160.201 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE...

  18. First Industrial Tests of a Matrix Monitor Correction for the Differential Die-away Technique of Historical Waste Drums

    SciTech Connect

    Antoni, Rodolphe; Passard, Christian; Perot, Bertrand; Grassi, Gabriele

    2015-07-01

    The fissile mass in radioactive waste drums filled with compacted metallic residues (spent fuel hulls and nozzles) produced at AREVA NC La Hague reprocessing plant is measured by neutron interrogation with the Differential Die-away measurement Technique (DDT). In the next years, old hulls and nozzles mixed with Ion-Exchange Resins will be measured. The ion-exchange resins increase neutron moderation in the matrix, compared to the waste measured in the current process. In this context, the Nuclear Measurement Laboratory (LMN) of CEA Cadarache has studied a matrix effect correction method, based on a drum monitor, namely a 3He proportional counter located inside the measurement cavity. After feasibility studies performed with LMN's PROMETHEE 6 laboratory measurement cell and with MCNPX simulations, this paper presents first experimental tests performed on the industrial ACC (hulls and nozzles compaction facility) measurement system. A calculation vs. experiment benchmark has been carried out by performing dedicated calibration measurements with a representative drum and {sup 235}U samples. The comparison between calculation and experiment shows a satisfactory agreement for the drum monitor. The final objective of this work is to confirm the reliability of the modeling approach and the industrial feasibility of the method, which will be implemented on the industrial station for the measurement of historical wastes. (authors)

  19. Fine cohesive powders in rotating drums: Transition from rigid-plastic flow to gas-fluidized regime

    NASA Astrophysics Data System (ADS)

    Castellanos, A.; Valverde, J. M.; Quintanilla, M. A.

    2002-06-01

    We investigate the dynamics of fine cohesive powders inside rotating drums. We show that these powders may be fluidized due to entrapment of ambient gas, and we determine the onset of fluidization. Experimental measurements on the bed expansion as a function of the rotation velocity have been performed. Drums of different diameters and fine powders of varying cohesiveness have been tested. We show that (i) fine powders transit directly from a rigid-plastic state to a gas-fluidized state in accordance with the flow regime boundaries predicted elsewhere [A. Castellanos et al., Phys. Rev. Lett. 82, 1156 (1999)], (ii) the onset of fluidization in the rotating drum is determined by the ratio of the powder kinetic energy per unit volume to its tensile strength, and (iii) once the powder is completely fluidized the average interstitial gas velocity increases proportionally to the rotation velocity. The last two results imply that the required velocity to fluidize a powder, ωR (ω angular velocity, R radius of the drum), must increase as the square root of its tensile strength, and this has been confirmed by independent measurements and estimations.

  20. Species profiles: life histories and environmental requirements of coastal fishes and invertebrates (Gulf of Mexico). Black drum. [Pogonias cromis

    SciTech Connect

    Sutter, F.C.; Waller, R.S.; McIlwain, T.D.

    1986-04-01

    Black drum are primarily an estuarine species. The time of black drum spawning depends on location. In Texas waters, heaviest spawning activity occurs during February and March near passes in open bays and estuaries, while in deeper Gulf waters they spawn from November to April. Larvae are transported into the estuarine environment where they grow to the juvenile stage, living in shallow, muddy waters, tolerating a wide range of environmental conditions. Black drum are commercially harvested by a variety of gears, with the majority of US landings taken in Gulf waters off Texas. They are also an important recreational species with more fish caught in the sport catch than harvested commercially. Young black drum feed on invertebrates and small fish, while adults consume mollusks and some decapods. Adults are found in salinities of 9 to 26 ppt and in water temperatures of 12 to 33/sup 0/C. Juveniles are taken over muddy bottoms and adults are usually found over sand or soft bottoms and over oyster reefs or clam shell.

  1. Proficiency test for non-destructive assay of 220 liter radioactive waste drums by gamma assay systems

    SciTech Connect

    Van Velzen, L.P.M.; Bruggeman, M.; Botte, J.

    2007-07-01

    The European Network of Testing Facilities for the Quality Checking of Radioactive Waste Packages (ENTRAP) initiated a feasibility study on how to organize in the most cost effective way an international proficiency tests for non-destructive, gamma-ray based, assay of 220 liter radioactive waste drums in the European Union at a regular time interval of 2 or 3 years. This feasibility study addresses all aspects of proficiency testing on radioactive waste packages including the design of a commonly accepted reference 220 liter drum. This design, based on the international response on a send out questionnaire, includes matrixes, radioactive sources; a solution to overcome the tedious and expensive international transport costs of real or even simulated waste packages, general cost estimation for the organization of, and the participation in the proficiency test. The proposed concept for the proficiency testing and the estimated costs are presented. The participation costs of the first proficiency test are mainly determined by the manufacturing of the non-radioactive 220 liter drum ({+-} 55%). Applied reference sources, transport of the drum and reference sources and participation costs in the proficiency test contribute each about {+-} 15%. (authors)

  2. Modification of whole flours of navy bean, pinto bean, black bean and chickpea by steam jet cooking and drum drying

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Whole bean flours of navy bean, pinto bean, black bean and chickpea were processed by excess steam jet cooking, drum drying, and milling to a state resembling the raw flours. Analysis of the structure and size of the particles, color, solubility and pasting characteristics, dietary fiber, and protei...

  3. Fluctuations of Hi-Hat Timing and Dynamics in a Virtuoso Drum Track of a Popular Music Recording

    PubMed Central

    Räsänen, Esa; Pulkkinen, Otto; Virtanen, Tuomas; Zollner, Manfred; Hennig, Holger

    2015-01-01

    Long-range correlated temporal fluctuations in the beats of musical rhythms are an inevitable consequence of human action. According to recent studies, such fluctuations also lead to a favored listening experience. The scaling laws of amplitude variations in rhythms, however, are widely unknown. Here we use highly sensitive onset detection and time series analysis to study the amplitude and temporal fluctuations of Jeff Porcaro’s one-handed hi-hat pattern in “I Keep Forgettin’”—one of the most renowned 16th note patterns in modern drumming. We show that fluctuations of hi-hat amplitudes and interbeat intervals (times between hits) have clear long-range correlations and short-range anticorrelations separated by a characteristic time scale. In addition, we detect subtle features in Porcaro’s drumming such as small drifts in the 16th note pulse and non-trivial periodic two-bar patterns in both hi-hat amplitudes and intervals. Through this investigation we introduce a step towards statistical studies of the 20th and 21st century music recordings in the framework of complex systems. Our analysis has direct applications to the development of drum machines and to drumming pedagogy. PMID:26039256

  4. CH Packaging Operations Manual

    SciTech Connect

    Washington TRU Solutions LLC

    2005-02-28

    This document provides the user with instructions for assembling a payload. All the steps in Subsections 1.2, Preparing 55-Gallon Drum Payload Assembly; 1.3, Preparing "Short" 85-Gallon Drum Payload Assembly (TRUPACT-II and HalfPACT); 1.4, Preparing "Tall" 85-Gallon Drum Payload Assembly (HalfPACT only); 1.5, Preparing 100-Gallon Drum Payload Assembly; 1.6, Preparing SWB Payload Assembly; and 1.7, Preparing TDOP Payload Assembly, must be completed, but may be performed in any order as long as radiological control steps are not bypassed.

  5. Pre-title I safety evaluation for the retrieval operations of transuranic waste drums in the Solid Waste Disposal Facility. Revision 2

    SciTech Connect

    Rabin, M.S.

    1992-08-01

    Phase I of the Transuranic (TRU) Waste Facility Line Item Project includes the retrieval and safe storage of the pad drums that are stored on TRU pads 2-6 in the Solid Waste Disposal Facility (SWDF). Drums containing TRU waste were placed on these pads as early as 1974. The pads, once filled, were mounded with soil. The retrieval activities will include the excavation of the soil, retrieval of the pad drums, placing the drums in overpacks (if necessary) and venting and purging the retrieved drums. Once the drums have been vented and purged, they will be transported to other pads within the SWDF or in a designated area until they are eventually treated as necessary for ultimate shipment to the Waste Isolation Pilot Plant in Carlsbad, New Mexico. This safety evaluation provides a bounding assessment of the radiological risk involved with the drum retrieval activities to the maximally exposed offsite individual and the co-located worker. The results of the analysis indicate that the risk to the maximally exposed offsite individual and the co-located worker using maximum frequencies and maximum consequences are within the acceptance criteria defined in WSRC Procedural Manual 9Q. The purpose of this evaluation is to demonstrate the incremental risk from the SWDF due to the retrieval activities for use as design input only. As design information becomes available, this evaluation can be revised to satisfy the safety analysis requirements of DOE Orders 4700 and 5480.23.

  6. Intelligent mobile sensor system for drum inspection and monitoring: Topical report, October 1, 1993--April 22, 1995

    SciTech Connect

    1997-04-01

    The objective of the Intelligent Mobile Sensor System (IMSS) project is to develop an operational system for monitoring and inspection activities for waste storage facility operations at several DOE sites. Specifically, the product of this effort is a robotic device with enhanced intelligence and maneuverability capable of conducting routine inspection of stored waste drums. The system has an integrated sensor suite for problem-drum detection, and is linked to a site database both for inspection planning and for data correlation, updating, and report generation. The system is capable of departing on an assigned mission, collecting required data, recording which portions of its mission had to be aborted or modified due to environmental constraints, and reporting back when the mission is complete. Successful identification of more than 96% of drum defects has been demonstrated in a high fidelity waste storage facility mockup. Identified anomalies included rust spots, rust streaks, areas of corrosion, dents, and tilted drums. All drums were positively identified and correlated with the site database. This development effort is separated into three phases of which phase two is now complete. The second phase demonstrated a prototype system appropriate for operational use in an actual storage facility. The prototype provides an integrated design that considers operational requirements, hardware costs, maintenance, safety, and robustness. The final phase will demonstrate commercial viability using the prototype vehicle in a pilot waste operations and inspection project. This report summarizes the design and evaluation of the new IMSS Phase 2 system and vehicle. Several parts of the IMSS Phase 1 Topical (Final) Report, which describes the requirements, design guidelines, and detailed design of the Phase 1 IMSS vehicle, are incorporated here, with modifications to reflect the changes in the design and the new elements added during the Phase 2 work.

  7. Intelligent Mobile Sensor System for drum inspection and monitoring -- Volume 2. Final report, October 1, 1993--April 22, 1995

    SciTech Connect

    1995-12-31

    The objective of the Intelligent Mobile Sensor System (IMSS) project was to develop an operational system for monitoring and inspection activities for waste storage facility operations at several DOE sites. Specifically, the product of this effort was a robotic device with enhanced intelligence and maneuverability capable of conducting routine inspection of stored waste drums. The system has an integrated sensor suite for problem-drum detection, and creates and maintains a site database both for inspection planning and for data correlation, updating, and report generation. The system is capable of departing on an assigned mission, collecting required data, recording which portions of its mission had to be aborted or modified due to environmental constraints, and reporting back when the mission is complete. Successful identification of more than 96% of drum defects has been demonstrated in a high fidelity waste storage facility mockup. Identified anomalies included rust spots, rust streaks, areas of corrosion, dents, and tilted drums. All drums were positively identified and correlated with the site database. This development effort was separated into three phases of which phase three is now complete. The first phase demonstrated an integrated system (maturity level IVa) for monitoring and inspection activities for waste storage facility operations. The second phase demonstrated a prototype system appropriate for operational use in an actual storage facility. The prototype employed an integrated design that considered operational requirements, hardware costs, maintenance, safety, and robustness. The final phase has demonstrated the commercial viability of the vehicle in operating waste storage facilities at Fernald, Ohio and the Idaho National Engineering Laboratory (INEL). This report summarizes the system upgrades performed in phase 3 and the evaluation of the IMSS Phase 3 system and vehicle.

  8. Intelligent mobile sensor system for drum inspection and monitoring: Phase 1. Topical report, October 1, 1992--June 8, 1993

    SciTech Connect

    Not Available

    1993-06-01

    The objective of this project was to develop an operational system for monitoring and inspection activities for waste storage facility operations at several DOE sites. Specifically, the product of this effort is a robotic device with enhanced intelligence and maneuverability capable of conducting routine inspection of stored waste drums. The device is capable of operating in narrow aisles and interpolating the free aisle space between rows of stacked drums. The system has an integrated sensor suite for leak detection, and is interfaced with a site database both for inspection planning and for data correlation, updating, and report generation. The system is capable of departing on an assigned mission, collecting required data, recording which positions of its mission had to be aborted or modified due to environmental constraints, and reporting back when the mission is complete. Successful identification of more than 90% of all drum defects has been demonstrated in a high fidelity waste storage facility mockup. Identified anomalies included rust spots, rust streaks, areas of corrosion, dents, and tilted drums. All drums were positively identified and correlated with the site database. This development effort is separated into three phases of which phase one is now complete. The first phase has demonstrated an integrated system for monitoring and inspection activities for waste storage facility operations. This demonstration system was quickly fielded and evaluated by leveraging technologies developed from previous NASA and DARPA contracts and internal research. The second phase will demonstrate a prototype system appropriate for operational use in an actual storage facility. The prototype provides an integrated design that considers operational requirements, hardware costs, maintenance, safety, and robustness. The final phase will demonstrate commercial viability using the prototype vehicle in a pilot waste operations and inspection project.

  9. Maraging Steel Machining Improvements

    DTIC Science & Technology

    2007-04-23

    APR 2007 2. REPORT TYPE Technical, Success Story 3. DATES COVERED 01-12-2006 to 23-04-2007 4. TITLE AND SUBTITLE Maraging Steel Machining...consumers of cobalt-strengthened maraging steel . An increase in production requires them to reduce the machining time of certain operations producing... maraging steel ; Success Stories 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT 1 18. NUMBER OF PAGES 1 19a. NAME OF RESPONSIBLE

  10. Eruptive history and petrology of Mount Drum volcano, Wrangell Mountains, Alaska

    USGS Publications Warehouse

    Richter, D.H.; Moll-Stalcup, E. J.; Miller, T.P.; Lanphere, M.A.; Dalrymple, G.B.; Smith, R.L.

    1994-01-01

    Mount Drum is one of the youngest volcanoes in the subduction-related Wrangell volcanic field (80x200 km) of southcentral Alaska. It lies at the northwest end of a series of large, andesite-dominated shield volcanoes that show a northwesterly progression of age from 26 Ma near the Alaska-Yukon border to about 0.2 Ma at Mount Drum. The volcano was constructed between 750 and 250 ka during at least two cycles of cone building and ring-dome emplacement and was partially destroyed by violent explosive activity probably after 250 ka. Cone lavas range from basaltic andesite to dacite in composition; ring-domes are dacite to rhyolite. The last constructional activity occured in the vicinity of Snider Peak, on the south flank of the volcano, where extensive dacite flows and a dacite dome erupted at about 250 ka. The climactic explosive eruption, that destroyed the top and a part of the south flank of the volcano, produced more than 7 km3 of proximal hot and cold avalanche deposits and distal mudflows. The Mount Drum rocks have medium-K, calc-alkaline affinities and are generally plagioclase phyric. Silica contents range from 55.8 to 74.0 wt%, with a compositional gap between 66.8 and 72.8 wt%. All the rocks are enriched in alkali elements and depleted in Ta relative to the LREE, typical of volcanic arc rocks, but have higher MgO contents at a given SiO2, than typical orogenic medium-K andesites. Strontium-isotope ratios vary from 0.70292 to 0.70353. The compositional range of Mount Drum lavas is best explained by a combination of diverse parental magmas, magma mixing, and fractionation. The small, but significant, range in 87Sr/86Sr ratios in the basaltic andesites and the wide range of incompatible-element ratios exhibited by the basaltic andesites and andesites suggests the presence of compositionally diverse parent magmas. The lavas show abundant petrographic evidence of magma mixing, such as bimodal phenocryst size, resorbed phenocrysts, reaction rims, and

  11. Composting domestic sewage sludge with natural zeolites in a rotary drum reactor.

    PubMed

    Villaseñor, J; Rodríguez, L; Fernández, F J

    2011-01-01

    This work aimed the influence of zeolites addition on a sludge-straw composting process using a pilot-scale rotary drum reactor. The type and concentration of three commercial natural zeolites were considered: a mordenite and two clinoptilolites (Klinolith and Zeocat). Mordenite caused the greatest carbon removal (58%), while the clinoptilolites halved losses of ammonium. All zeolites removed 100% of Ni, Cr, Pb, and significant amounts (more than 60%) of Cu, Zn and Hg. Zeocat displayed the greatest retention of ammonium and metals, and retention efficiencies increased as Zeocat concentration increased. The addition of 10% Zeocat produced compost compliant with Spanish regulations. Zeolites were separated from the final compost, and leaching studies suggested that zeolites leachates contained very low metals concentrations (<1 mg/kg). Thus, the final compost could be applied directly to soil, or metal-polluted zeolites could be separated from the compost prior to application. The different options have been discussed.

  12. Hypoxia tolerance decreases with body size in red drum Sciaenops ocellatus.

    PubMed

    Pan, Y K; Ern, R; Esbaugh, A J

    2016-08-01

    Mass-specific oxygen consumption rate, i.e. standard metabolic rate (Rs ) and critical oxygen tension (Pcrit ) of red drum Sciaenops ocellatus were measured and scaled over a 2500-fold range in mass (MF ; 0·26-686 g). Rs conformed to well established models (Rs  = 3·73·91 MF (-0·21) ; r(2)  = 0·86) while Pcrit increased over the size range (Pcrit  = 3·15 log10 MF  + 16·19; r(2)  = 0·44). This relationship may be ecologically advantageous as it would allow smaller S. ocellatus to better utilize hypoxic zones as habitat and refuge from predators.

  13. Quality enhancement in refrigerated red drum (Sciaenops ocellatus) fillets using chitosan coatings containing natural preservatives.

    PubMed

    Li, Tingting; Li, Jianrong; Hu, Wenzhong; Li, Xuepeng

    2013-06-01

    The present work was undertaken to examine the influence of grape seed extract (GS) and tea polyphenols (TP), as natural preservatives, combined with chitosan (Ch), on the quality of red drum (Sciaenops ocellatus) fillets during refrigerated storage. Two different treatments (Ch+GS and Ch+TP) and a control were prepared. The samples were stored (4 ± 1°C) for 20 days and the sampling was done at 0, 4, 8, 12, 16, 20 days. Microbiological, physicochemical and sensory attributes were periodically assessed. The results indicated that the two pretreatments could more effectively maintain quality and could extend the shelf life by 6-8 days compared with the control group during refrigerated storage.

  14. THERMAL EVALUATION OF DRUM TYPE RADIOACTIVE MATERIAL PACKAGING ARRAYS IN STORAGE

    SciTech Connect

    Gupta, N

    2009-04-27

    Drum type packages are routinely used to transport radioactive material (RAM) in the U.S. Department of Energy (DOE) complex. These packages are designed to meet the federal regulations described in 10 CFR 71.[1] In recent years, there has been a greater need to use these packagings to store the excess fissile material, especially plutonium for long term storage. While the design requirements for safe transportation of these packagings are well defined, the requirements for safe long term storage are not well established. Since the RAM contents in the packagings produce decay heat, it is important that they are stored carefully to prevent overheating of the containment vessel (CV) seals to prevent any leakage and the impact limiter to maintain the package structural integrity. This paper analyzes different storage arrays for a typical 9977 packaging for thermal considerations and makes recommendations for their safe storage under normal operating conditions.

  15. In-drum vitrification of transuranic waste sludge using microwave energy

    SciTech Connect

    Petersen, R.D.; Johnson, A.J.

    1989-01-01

    Microwave vitrification of transuranic (TRU) waste at the Rocky Flats nuclear weapons plant is being tested using actual TRU waste in a bench-scale system and simulated waste in a pilot system. In 1987, bench-scale testing was completed to determine the effectiveness of in-drum microwave vitrification of simulated precipitation sludge. The equipment used in the bench tests included a 6-kW, 2.45-GHz microwave generator, aluminum cavity, turntable, infrared (IR) thermometer, and screw feeder. Results similar to those achieved in bench-scale testing are reproducible using a 915-MHz microwave system in solidifying simulated TRU sludge. Nine samples have been processed to date. Also, preliminary results using actual TRU waste indicate that the actual waste will behave in a similar way to the surrogate waste used in the 2.45-GHz system. Work is ongoing to complete the TRU waste tests.

  16. Cochlear implant users move in time to the beat of drum music.

    PubMed

    Phillips-Silver, Jessica; Toiviainen, Petri; Gosselin, Nathalie; Turgeon, Christine; Lepore, Franco; Peretz, Isabelle

    2015-03-01

    Cochlear implant users show a profile of residual, yet poorly understood, musical abilities. An ability that has received little to no attention in this population is entrainment to a musical beat. We show for the first time that a heterogeneous group of cochlear implant users is able to find the beat and move their bodies in time to Latin Merengue music, especially when the music is presented in unpitched drum tones. These findings not only reveal a hidden capacity for feeling musical rhythm through the body in the deaf and hearing impaired population, but illuminate promising avenues for designing early childhood musical training that can engage implanted children in social musical activities with benefits potentially extending to non-musical domains.

  17. Characterization of a water pump for drum-type washing machine by vibration power approach

    NASA Astrophysics Data System (ADS)

    Heo, YongHwa; Kim, Kwang-joon

    2015-03-01

    Water pumps used in drum-type washing machines to save water are likely to make the washing process noisier than the one without those because the water pumps attached usually onto cabinet structure work as additional vibration and noise sources. In order to either counteract such vibration and noise problems by stiffness design of the cabinet structure or classify the water pumps from the view point of an acceptance test, characterization of the water pumps as excitation sources would be essential. In this paper, several methods to characterize a water pump as an excitation source are investigated. Measurements by traditional methods of blocked force and/or free velocity for a water pump of 35 W are presented. Two methods of vibration power suggested rather recently are reviewed. Then, another method of the vibration power is proposed. Estimations of the vibration power for the water pump operating on a beam structure are obtained and discussed comparatively.

  18. Spectroscopy of annular drums and quantum rings: Perturbative and nonperturbative results

    SciTech Connect

    Alvarado, Carlos; Amore, Paolo

    2011-06-15

    We obtain systematic approximations to the states (energies and wave functions) of quantum rings (annular drums) of arbitrary shape by conformally mapping the annular domain to a simply connected domain. Extending the general results of Amore [J. Math. Phys. 51, 052105 (2010)], we obtain an analytical formula for the spectrum of quantum ring of arbitrary shape: for the cases of a circular annulus and of an asymmetric annulus considered here this formula is remarkably simple and precise. We also obtain precise variational bounds for the ground state of different quantum rings. Finally, we extend the conformal collocation method of Amore [J. Math. Phys. 51, 052105 (2010); J. Phys. A 41, 265206 (2008)] to the class of problems considered here and calculate precise numerical solutions for a large number of states ({approx_equal}2000).

  19. Numerical simulation of two-dimensional steady granular flows in rotating drum: On surface flow rheology

    NASA Astrophysics Data System (ADS)

    Renouf, M.; Bonamy, D.; Dubois, F.; Alart, P.

    2005-10-01

    The rheology of two-dimensional steady surface flow of cohesionless cylinders in a rotating drum is investigated through nonsmooth contact dynamics simulations. Profiles of volume fraction, translational and angular velocity, rms velocity, strain rate, and stress tensor are measured at the midpoint along the length of the surface-flowing layer, where the flow is generally considered as steady and homogeneous. Analysis of these data and their interrelations suggest the local inertial number—defined as the ratio between local inertial forces and local confinement forces—to be the relevant dimensionless parameter to describe the transition from the quasistatic part of the packing to the flowing part at the surface of the heap. Variations of the components of the stress tensor as well as the ones of rms velocity as a function of the inertial number are analyzed within both the quasistatic and the flowing phases. Their implications are discussed.

  20. Eruptive history and petrology of Mount Drum volcano, Wrangell Mountains, Alaska

    NASA Astrophysics Data System (ADS)

    Richter, D. H.; Moll-Stalcup, E. J.; Miller, T. P.; Lanphere, M. A.; Dalrymple, G. B.; Smith, R. L.

    1994-03-01

    Mount Drum is one of the youngest volcanoes in the subduction-related Wrangell volcanic field (80×200 km) of southcentral Alaska. It lies at the northwest end of a series of large, andesite-dominated shield volcanoes that show a northwesterly progression of age from 26 Ma near the Alaska-Yukon border to about 0.2 Ma at Mount Drum. The volcano was constructed between 750 and 250 ka during at least two cycles of cone building and ring-dome emplacement and was partially destroyed by violent explosive activity probably after 250 ka. Cone lavas range from basaltic andesite to dacite in composition; ring-domes are dacite to rhyolite. The last constructional activity occurred in the vicinity of Snider Peak, on the south flank of the volcano, where extensive dacite flows and a dacite dome erupted at about 250 ka. The climactic explosive eruption, that destroyed the top and a part of the south flank of the volcano, produced more than 7 km3 of proximal hot and cold avalanche deposits and distal mudflows. The Mount Drum rocks have medium-K, calc-alkaline affinities and are generally plagioclase phyric. Silica contents range from 55.8 to 74.0 wt%, with a compositional gap between 66.8 and 72.8 wt%. All the rocks are enriched in alkali elements and depleted in Ta relative to the LREE, typical of volcanic arc rocks, but have higher MgO contents at a given SiO2, than typical orogenic medium-K andesites. Strontium-isotope ratios vary from 0.70292 to 0.70353. The compositional range of Mount Drum lavas is best explained by a combination of diverse parental magmas, magma mixing, and fractionation. The small, but significant, range in 87Sr/86Sr ratios in the basaltic andesites and the wide range of incompatible-element ratios exhibited by the basaltic andesites and andesites suggests the presence of compositionally diverse parent magmas. The lavas show abundant petrographic evidence of magma mixing, such as bimodal phenocryst size, resorbed phenocrysts, reaction rims, and

  1. Welding irradiated stainless steel

    SciTech Connect

    Kanne, W.R. Jr.; Chandler, G.T.; Nelson, D.Z.; Franco-Ferreira, E.A.

    1993-12-31

    Conventional welding processes produced severe underbead cracking in irradiated stainless steel containing 1 to 33 appm helium from n,a reactions. A shallow penetration overlay technique was successfully demonstrated for welding irradiated stainless steel. The technique was applied to irradiated 304 stainless steel that contained 10 appm helium. Surface cracking, present in conventional welds made on the same steel at the same and lower helium concentrations, was eliminated. Underbead cracking was minimal compared to conventional welding methods. However, cracking in the irradiated material was greater than in tritium charged and aged material at the same helium concentrations. The overlay technique provides a potential method for repair or modification of irradiated reactor materials.

  2. Cyclic mRNA expression of thyrotropin subunits and deiodinases in red drum, Sciaenops ocellatus.

    PubMed

    Jones, R A; Cohn, W B; Miller, T C; Jaques, J T; Mackenzie, D S

    2013-12-01

    The role of thyrotropin (thyroid-stimulating hormone, TSH) in driving peripheral thyroid function in non-mammalian species is still poorly understood. Thyroxine (T₄), the principal hormone released from the thyroid gland in response to TSH stimulation, circulates with a robust daily rhythm in the teleost fish the red drum. Previous research suggests that the red drum T₄ cycle is circadian in nature, driven by TSH secretion in the early photophase and inhibited by T₄ feedback in the early scotophase. To determine whether TSH is produced in a pattern consistent with feedback inhibition by this T₄ cycle, we used quantitative real time PCR (qPCR) to quantify the daily cycle of expression of the pituitary TSH subunits GSUα, and TSHβ. We found that TSH expression cycled inversely to, and 6-12 h out of phase with, the T₄ cycle, consistent with the hypothesis that TSH secretion drives the T₄ cycle. To examine the potential role of deiodinases in negative feedback regulation of this TSH cycle, we also utilized qPCR to assess the pituitary expression patterns of the TH activating enzyme outer-ring deiodinase (Dio2) and the TH deactivating enzyme inner-ring deiodinase (Dio3). Dio2 was not expressed with an obvious daily cycle, whereas Dio3 expression mirrored the expression of TSH. These results are consistent with circulating T₄ providing the negative feedback signal controlling both TSH production and Dio3 expression in the pituitary, and suggest that TH inactivation by inner ring deiodination is an important component of TSH negative feedback control.

  3. Negative feedback regulation of thyrotropin subunits and pituitary deiodinases in red drum, Sciaenops ocellatus.

    PubMed

    Jones, R A; Cohn, W B; Wilkes, A A; MacKenzie, D S

    2017-01-01

    Thyroxine (T4) undergoes dynamic daily cycles in the perciform fish the red drum, Sciaenops ocellatus, that are inversely timed to cycles of thyrotropin (TSH) subunit mRNA expression in the pituitary gland. We have proposed that these daily cycles are regulated by negative feedback of circulating T4 on expression of pituitary thyroid hormone deiodinase type 3 (Dio3), such that elevated circulating T4 results in diminished pituitary thyroid hormone catabolism and consequent increased negative feedback on expression of TSH subunits during the day. To determine whether thyroid hormones function to modulate expression of pituitary deiodinase enzymes we developed an immersion technique to administer physiological doses of T3 and T4in vivo. Immersion in T4 or T3 significantly inhibited the mRNA expression of the TSH α and β subunits from 4 to 66h of immersion. Pituitary Dio3 expression was significantly diminished by T3 and T4 at 22h. These results indicate that both T4 and T3 are capable of negative feedback regulation of TSH subunit expression in red drum at physiological concentrations and on a time scale consistent with the T4 daily cycle. Furthermore, thyroid hormones negatively regulate Dio3 expression in the pituitary in a manner suggesting that negative thyroxine feedback on Dio3 promotes the release of TSH subunits from TH inhibition and may be an important mechanism for generating daily thyroid hormone cycles. These results highlight a potentially important role for D3 in mediating thyroid hormone feedback on TSH expression, not previously described in other species.

  4. Simulation of rotary-drum and repose tests for frictional spheres and rigid sphere clusters

    SciTech Connect

    Walton, O.R.; Braun, R.L.

    1993-11-01

    The effects of rotation rate and interparticle friction on the bulk flow behavior in rotating horizontal cylinders are studied via particle-dynamic simulations. Assemblies of inelastic, frictional spheres and rigid sphere clusters are utilized, and rotation rates from quasistatic to centrifuging are examined. Flow phenomena explored include size segregation, avalanching, slumping and centrifuging. Simulated drum flows with two sizes of frictional spheres showed very rapid segregation of species perpendicular to the drum axis; however, simulations of up to 10 revolutions, utilizing periodic-boundary ends, did not exhibit the experimentally observed axial segregation into stripes. Angles of repose for uniform-sized spheres in slowly rotating cylinders varied from 13 to 31 degrees as the friction coefficient varied from 0.02 to 1.0. For simulated rotation rates higher than the threshold to obtain uniform flow conditions, the apparent angle of repose increases as the rotation rats increases, consistent with experiments. Also, simulations with rigid clusters of 4 spheres in a tetrahedral shape or 8 spheres in a cubical arrangement, demonstrate that particle shape strongly influences the repose angle. Simulations of cubical 8-sphere clusters, with a surface coefficient of friction of 0.1, produced apparent angles of repose exceeding 35 degrees, compared to 23 degrees for assemblies of single spheres interacting with the same force model parameters. Centrifuging flows at very high rotation rates exist as stationary beds moving exactly as the outer rotating wall. At somewhat slower speeds the granular bed remains in contact with the wall but exhibits surface sliding down the rising inner bed surface, moving a short distance on each revolution. At still slower speeds particles rain from the surface of the upper half of the rotating bed.

  5. Rotary Drum Separator and Pump for the Sabatier Carbon Dioxide Reduction System

    NASA Technical Reports Server (NTRS)

    Holder, Don; Fort, James; Barone, Michael; Murdoch, Karen

    2005-01-01

    A trade study conducted in 2001 selected a rotary disk separator as the best candidate to meet the requirements for an International Space Station (ISS) Carbon Dioxide Reduction Assembly (CRA). The selected technology must provide micro-gravity gasfliquid separation and pump the liquid from 10 psia at the gasfliquid interface to 18 psia at the wastewater bus storage tank. The rotary disk concept, which has pedigree in other systems currently being built for installation on the ISS, failed to achieve the required pumping head within the allotted power. The separator discussed in this paper is a new design that was tested to determine compliance with performance requirements in the CRA. The drum separator and pump @SP) design is similar to the Oxygen Generator Assembly (OGA) Rotary Separator Accumulator (RSA) in that it has a rotating assembly inside a stationary housing driven by a integral internal motor. The innovation of the DSP is the drum shaped rotating assembly that acts as the accumulator and also pumps the liquid at much less power than its predecessors. In the CRA application, the separator will rotate at slow speed while accumulating water. Once full, the separator will increase speed to generate sufficient head to pump the water to the wastewater bus. A proof-of- concept (POC) separator has been designed, fabricated and tested to assess the separation efficiency and pumping head of the design. This proof-of-concept item was flown aboard the KC135 to evaluate the effectiveness of the separator in a microgravity environment. This separator design has exceeded all of the performance requirements. The next step in the separator development is to integrate it into the Sabatier Carbon Dioxide Reduction System. This will be done with the Sabatier Engineering Development Unit at the Johnson Space Center.

  6. Bioinformatic comparisons and tissue expression of the neuronal nitric oxide synthase (nNOS) gene from the red drum (Sciaenops ocellatus).

    PubMed

    Zhou, Libin; Bai, Ru; Tian, Jianxiao; Liu, Xiaochun; Lu, Danqi; Zhu, Pei; Liu, Yun; Zeng, Lujiao; Luo, Wenna; Zhang, Yong; Wang, Anli

    2009-10-01

    The full length cDNA sequence for neuronal nitric oxide synthase (nNOS) gene from red drum (Sciaenops ocellatus) has been cloned, subjected to bioinformatic analysis, and examined for expression in different tissues. Red drum nNOS showed high identity to nNOS of mammals and other fish species. Notably, a unique 7-aa insertion was found in the important catalytic sites of the NO synthase domain, possibly affecting the function of red drum nNOS. Furthermore, this nNOS was expressed not only in brain but also in most of the internal organs including liver, intestine, spleen, head kidney and thymus.

  7. The calculation of quality indices of the water heat carrier and estimation of the condition of water chemistry of drum boilers

    NASA Astrophysics Data System (ADS)

    Larin, B. M.; Larin, A. B.; Kozyulina, E. V.; Kolegov, A. V.

    2012-07-01

    There is suggested a method for an indirect calculated identification of ionic impurities in water of drum boilers ( p b = 13.8 MPa) by means of measuring the electric conductivity of cooled samples (direct and H-cationized ones) of the feedwater and drum water. This paper reports the results of an industrial experiment carried out on the drum power boiler during the entire heating season. The possibility of evaluating the condition of the water chemistry, with plotting a phase diagram of the phosphate-based water chemistry and determining characteristic dependences, is shown.

  8. Gamma-ray spectrometry method used for radioactive waste drums characterization for final disposal at National Repository for Low and Intermediate Radioactive Waste--Baita, Romania.

    PubMed

    Done, L; Tugulan, L C; Dragolici, F; Alexandru, C

    2014-05-01

    The Radioactive Waste Management Department from IFIN-HH, Bucharest, performs the conditioning of the institutional radioactive waste in concrete matrix, in 200 l drums with concrete shield, for final disposal at DNDR - Baita, Bihor county, in an old exhausted uranium mine. This paper presents a gamma-ray spectrometry method for the characterization of the radioactive waste drums' radionuclides content, for final disposal. In order to study the accuracy of the method, a similar concrete matrix with Portland cement in a 200 l drum was used.

  9. Use of polyethylene pellets in the design and construction of a storage safe, a transport vessel and a portable shield for californium-252

    SciTech Connect

    Sharma, S.

    1986-01-01

    A storage and shielding facility for 300 ..mu..g of Californium-252 sources was designed and constructed. Though the safe was in a permanent location, the fact that it consisted of a lead bucket surrounded by polyethylene pellets made it simple, movable and inexpensive. If need be, more quantities of Cf-252 could be added without altering the basic design and sacrificing the radiation protection guidelines. The measured radiation levels from 300 ..mu..g of stored Cf-252 in and around the storage vault were lower than the expected dose rates by a factor of 5. The measured radiation levels around the occupied environs of the facility were below the maximum permissible yearly dose of 500mrem for non-occupational workers. A transport vessel was designed and constructed to carry up to 50 ..mu..g of Californium-252 sources. It consisted of a standard 55 gallon steel drum on casters containing cylindrical lead shield surrounded by polyethylene pellets. The measured maximum surface dose rates on the drum and at one meter away were within the radiation protection guidelines and were less than the expected dose rates. A portable shield was designed and constructed to protect the body in afterloading operations and handling of the sources. It consisted of polyethylene pellets in an aluminum box and an attached 10 cm thick plexiglass eye shield. The simple design, with the ease of using polyethylene pellets can be extended to construct bedside shields.

  10. Coated 4340 Steel

    DTIC Science & Technology

    2013-08-26

    the effects of three coating systems on the mechanical property, fatigue, and...defined striations or striations-like features were formed in air, Figure A-13(b). On the other hand, intergranular cracking and formation of brittle...steel, in air. Their respective effects on the fatigue resistance of bare 4340 steel were similar in both of the employed environments, air and

  11. Steel Industry Wastes.

    ERIC Educational Resources Information Center

    Schmidtke, N. W.; Averill, D. W.

    1978-01-01

    Presents a literature review of wastes from steel industry, covering publications of 1976-77. This review covers: (1) coke production; (2) iron and steel production; (3) rolling operations; and (4) surface treatment. A list of 133 references is also presented. (NM)

  12. Machine Vision for Object Detection and Profiling in an Unstructured Environment

    SciTech Connect

    Walton, Miles Conley; Kinoshita, Robert Arthur

    2002-08-01

    The Handling and Sorting System for 55-Gallon Drums (HANDSS-55) is a DOE project to develop an automated method for retrieving items that are not acceptable at the Waste Isolation Pilot Plant (WIPP) from 55-gallon drums of low-level waste. The HANDSS-55 is a modular system that opens drums, sorts the waste, and then repackages the remaining waste in WIPP compliant barrels. The Sorting Station module relies on a non-contact measurement system to quickly provide a 3D profile of the sorting area. It then analyses the 3D profile and a color image to determine the position and orientation of an operator selected waste item. The item is then removed from the sorting area by a robotic arm. The use of both image and profile information for object determination provides a fast, effective method of finding and retrieving selected objects in the unstructured environment of the sorting module.

  13. Machine Vision for Object Detection and Profiling in an Unstructured Environment

    SciTech Connect

    Kinoshita, R.A.; Walton, M.C.

    2002-05-23

    The Handling and Sorting System for 55-Gallon Drums (HANDSS-55) is a DOE project to develop an automated method for retrieving items that are not acceptable at the Waste Isolation Pilot Plant (WIPP) from 55-gallon drums of low-level waste. The HANDSS-55 is a modular system that opens drums, sorts the waste, and then repackages the remaining waste in WIPP compliant barrels. The Sorting Station module relies on a non-contact measurement system to quickly provide a 3D profile of the sorting area. It then analyses the 3D profile and a color image to determine the position and orientation of an operator selected waste item. The item is then removed from the sorting area by a robotic arm. The use of both image and profile information for object determination provides a fast, effective method of finding and retrieving selected objects in the unstructured environment of the sorting module.

  14. EAST ELEVATION, LTV STEEL (FORMERLY REPUBLIC STEEL), 8" BAR MILL, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    EAST ELEVATION, LTV STEEL (FORMERLY REPUBLIC STEEL), 8" BAR MILL, BUFFALO PLANT. VIEW LOOKING SOUTHWEST FROM ROLL SHOP. 8" BAR MILL DESIGNED AND BUILT BY DONNER STEEL CO. (PREDECESSOR OF REPUBLIC), 1919-1920. FOR DESCRIPTION OF ORIGINAL MILL SEE "IRON AGE", 116\\4 (23 JULY 1925): 201-204. - LTV Steel, 8-inch Bar Mill, Buffalo Plant, Buffalo, Erie County, NY

  15. The drug-minded protein interaction database (DrumPID) for efficient target analysis and drug development.

    PubMed

    Kunz, Meik; Liang, Chunguang; Nilla, Santosh; Cecil, Alexander; Dandekar, Thomas

    2016-01-01

    The drug-minded protein interaction database (DrumPID) has been designed to provide fast, tailored information on drugs and their protein networks including indications, protein targets and side-targets. Starting queries include compound, target and protein interactions and organism-specific protein families. Furthermore, drug name, chemical structures and their SMILES notation, affected proteins (potential drug targets), organisms as well as diseases can be queried including various combinations and refinement of searches. Drugs and protein interactions are analyzed in detail with reference to protein structures and catalytic domains, related compound structures as well as potential targets in other organisms. DrumPID considers drug functionality, compound similarity, target structure, interactome analysis and organismic range for a compound, useful for drug development, predicting drug side-effects and structure-activity relationships.Database URL:http://drumpid.bioapps.biozentrum.uni-wuerzburg.de.

  16. The drug-minded protein interaction database (DrumPID) for efficient target analysis and drug development

    PubMed Central

    Kunz, Meik; Liang, Chunguang; Nilla, Santosh; Cecil, Alexander; Dandekar, Thomas

    2016-01-01

    The drug-minded protein interaction database (DrumPID) has been designed to provide fast, tailored information on drugs and their protein networks including indications, protein targets and side-targets. Starting queries include compound, target and protein interactions and organism-specific protein families. Furthermore, drug name, chemical structures and their SMILES notation, affected proteins (potential drug targets), organisms as well as diseases can be queried including various combinations and refinement of searches. Drugs and protein interactions are analyzed in detail with reference to protein structures and catalytic domains, related compound structures as well as potential targets in other organisms. DrumPID considers drug functionality, compound similarity, target structure, interactome analysis and organismic range for a compound, useful for drug development, predicting drug side-effects and structure–activity relationships. Database URL: http://drumpid.bioapps.biozentrum.uni-wuerzburg.de PMID:27055828

  17. Superfund Record of Decision (EPA Region 3): Harvey-Knott Drum site, New Castle County, Delaware, September 1985. Final report

    SciTech Connect

    Not Available

    1985-09-30

    The Harvey-Knott Drum Site is located in New Castle County, Delaware, approximately one-half mile east of the Maryland-Delaware border. The Harvey and Knotts Trucking, Inc., operated an open dump and burning ground on the site between 1963 and 1969. The facility accepted sanitary, municipal, and industrial wastes believed to be sludges, paint pigments, and solvents. Wastes were emptied onto the ground, into excavated trenches, or left in drums (some of which were buried). Some of these wastes were either burned as a means of reducing waste volume, or allowed to seep into the soil. Contamination of soil, surface water, and ground water has occurred as a result of disposal of these industrial wastes. The selected remedial action for this site is included.

  18. Reconstruction of the activity of point sources for the accurate characterization of nuclear waste drums by segmented gamma scanning.

    PubMed

    Krings, Thomas; Mauerhofer, Eric

    2011-06-01

    This work improves the reliability and accuracy in the reconstruction of the total isotope activity content in heterogeneous nuclear waste drums containing point sources. The method is based on χ(2)-fits of the angular dependent count rate distribution measured during a drum rotation in segmented gamma scanning. A new description of the analytical calculation of the angular count rate distribution is introduced based on a more precise model of the collimated detector. The new description is validated and compared to the old description using MCNP5 simulations of angular dependent count rate distributions of Co-60 and Cs-137 point sources. It is shown that the new model describes the angular dependent count rate distribution significantly more accurate compared to the old model. Hence, the reconstruction of the activity is more accurate and the errors are considerably reduced that lead to more reliable results. Furthermore, the results are compared to the conventional reconstruction method assuming a homogeneous matrix and activity distribution.

  19. Effects of Group Drumming Interventions on Anxiety, Depression, Social Resilience and Inflammatory Immune Response among Mental Health Service Users

    PubMed Central

    Fancourt, Daisy; Perkins, Rosie; Ascenso, Sara; Carvalho, Livia A.; Steptoe, Andrew; Williamon, Aaron

    2016-01-01

    Growing numbers of mental health organizations are developing community music-making interventions for service users; however, to date there has been little research into their efficacy or mechanisms of effect. This study was an exploratory examination of whether 10 weeks of group drumming could improve depression, anxiety and social resilience among service users compared with a non-music control group (with participants allocated to group by geographical location.) Significant improvements were found in the drumming group but not the control group: by week 6 there were decreases in depression (-2.14 SE 0.50 CI -3.16 to -1.11) and increases in social resilience (7.69 SE 2.00 CI 3.60 to 11.78), and by week 10 these had further improved (depression: -3.41 SE 0.62 CI -4.68 to -2.15; social resilience: 10.59 SE 1.78 CI 6.94 to 14.24) alongside significant improvements in anxiety (-2.21 SE 0.50 CI -3.24 to -1.19) and mental wellbeing (6.14 SE 0.92 CI 4.25 to 8.04). All significant changes were maintained at 3 months follow-up. Furthermore, it is now recognised that many mental health conditions are characterised by underlying inflammatory immune responses. Consequently, participants in the drumming group also provided saliva samples to test for cortisol and the cytokines interleukin (IL) 4, IL6, IL17, tumour necrosis factor alpha (TNFα), and monocyte chemoattractant protein (MCP) 1. Across the 10 weeks there was a shift away from a pro-inflammatory towards an anti-inflammatory immune profile. Consequently, this study demonstrates the psychological benefits of group drumming and also suggests underlying biological effects, supporting its therapeutic potential for mental health. Trial Registration: ClinicalTrials.gov NCT01906892 PMID:26974430

  20. Damascus steel ledeburite class

    NASA Astrophysics Data System (ADS)

    Sukhanov, D. A.; Arkhangelsky, L. B.; Plotnikova, N. V.

    2017-02-01

    Discovered that some of blades Damascus steel has an unusual nature of origin of the excess cementite, which different from the redundant phases of secondary cementite, cementite of ledeburite and primary cementite in iron-carbon alloys. It is revealed that the morphological features of separate particles of cementite in Damascus steels lies in the abnormal size of excess carbides having the shape of irregular prisms. Considered three hypotheses for the formation of excess cementite in the form of faceted prismatic of excess carbides. The first hypothesis is based on thermal fission of cementite of a few isolated grains. The second hypothesis is based on the process of fragmentation cementite during deformation to the separate the pieces. The third hypothesis is based on the transformation of metastable cementite in the stable of angular eutectic carbide. It is shown that the angular carbides are formed within the original metastable colony ledeburite, so they are called “eutectic carbide”. It is established that high-purity white cast iron is converted into of Damascus steel during isothermal soaking at the annealing. It was revealed that some of blades Damascus steel ledeburite class do not contain in its microstructure of crushed ledeburite. It is shown that the pattern of carbide heterogeneity of Damascus steel consists entirely of angular eutectic carbides. Believe that Damascus steel refers to non-heat-resistant steel of ledeburite class, which have similar structural characteristics with semi-heat-resistant die steel or heat-resistant high speed steel, differing from them only in the nature of excess carbide phase.

  1. The Underwater Recovery of Monumental Marble Column Drums from an Ancient Shipwreck at Kızılburun, Turkey

    NASA Astrophysics Data System (ADS)

    Carlson, Deborah N.

    2016-08-01

    In the first century B.C., a stone carrier sank off the Aegean coast of Turkey at Kızılburun transporting all the elements of a monumental marble column, including a single Doric capital and eight drums. The 60-tonne cargo lay at a depth of 45-48 m and was excavated in its entirety by the Institute of Nautical Archaeology at Texas A&M University between 2005 and 2011. Ongoing research has shown that the Doric column pieces in the Kızılburun cargo originated in the marble quarries on Proconnesus Island in the Sea of Marmara and were very likely heading for the Temple of Apollo at Claros when the ship sank just 50 km short of its destination. The complete recovery of the ship's cargo posed a unique set of methodological challenges involving lifting the multi-tonne marble drums without disturbing the delicate waterlogged wooden hull remains preserved beneath. This report summarizes the solutions developed over five seasons in order to rig, hoist, move, and ultimately raise to the surface eight large ancient marble column drums (as well as all the other marble artifacts in the cargo) from a depth of almost 50 m under water.

  2. Transient natural convection and conduction heat transfers on hot box of a coke drum in Pre-heating stage

    NASA Astrophysics Data System (ADS)

    Siahaan, A. S.; Ambarita, H.; Kawai, H.; Daimaruya, M.

    2017-01-01

    In an oil refinery unit, coke drum is subjected cyclic thermal stress and mechanical loads due to cyclic heating and cooling loads. Thus, the useful life of a coke drum is much shorter than other equipment. One of the most severe locations due to thermal stress is shell to skirt junction. Here, a hot box is proposed. In this study effectiveness of a hot box will be analyzed numerically. The addition of hot box (triangular cavity) was expected to generate natural convection, which will enhance heat transfer. As for the result show that heat flux conduction and natural convection have the same trend. The peak of conduction heat flux is 122 W/m2 and for natural convection is 12 W/m2. In the heating stage of coke drum cycle it found that the natural convection only provide approximately 10 % of heat transfer compare to conduction heat transfer. In this study it was proved that in the heating stage, the addition of triangular enclosure is less effective to enhance the heat transfer than previously thought.

  3. A nanogenerator as a self-powered sensor for measuring the vibration spectrum of a drum membrane.

    PubMed

    Yu, Aifang; Zhao, Yong; Jiang, Peng; Wang, Zhong Lin

    2013-02-08

    A nanogenerator (NG) is a device that converts vibration energy into electricity. Here, a flexible, small size and lightweight NG is successfully demonstrated as an active sensor for detecting the vibration spectrum of a drum membrane without the use of an external power source. The output current/voltage signal of the NG is a direct measure of the strain of the local vibrating drum membrane that contains rich informational content, such as, notably, the vibration frequency, vibration speed and vibration amplitude. In comparison to the laser vibrometer, which is excessively complex and expensive, this kind of small and low cost sensor based on an NG is also capable of detecting the local vibration frequency of a drum membrane accurately. A spatial arrangement of the NGs on the membrane can provide position-dependent vibration information on the surface. The measured frequency spectrum can be understood on the basis of the theoretically calculated vibration modes. This work expands the application of NGs and reveals the potential for developing sound wave detection, environmental/infrastructure monitoring and many more applications.

  4. Three dimensional reconstruction of activity profiles in 220 liters radioactive waste packages containing super-compacted 100 liters drums

    SciTech Connect

    Van Velzen, L.P.M.; Maes, J.

    2007-07-01

    The 3DRedact project's main objective is the development of a non-destructive assay (NDA) system that can replace emission computer tomography (ECT) and transmission computer tomography (TCT) for the routine characterization of decayed radioactive waste 220 liters drums. The existing fast NDA scan system has been extended with a transmission system that fulfils the requirements of fast scan measurements. The design parameters and engineering are described. As a consequence of this extension the analyze program HOLIS had to be updated, so that HOLIS can make full advantage of the transmission data generated by the analysis of a 220 liters waste drum, containing different super compacted drums. The achievements of the new HOLIS version are presented. As a first assessment, based on the presented tests results, the accuracy of the calculated coordinates of hotspots can be assessed for all coordinates {+-} 1 cm and for the activity of the hot-spot {+-} 5 %. These accuracies are within the predefined requirements e.g. coordinates uncertainty {+-} 2 cm and activity less than 10 %. Further, additional safety systems have been installed to improve a healthy and save working environment. (authors)

  5. Cobalt free maraging steel

    SciTech Connect

    Floreen, S.

    1984-04-17

    The subject invention is directed to ferrous-base alloys, particularly to a cobalt-free maraging steel of novel chemistry characterized by a desired combination of strength and toughness, notwithstanding that cobalt is non-essential.

  6. Structural Amorphous Steels

    NASA Astrophysics Data System (ADS)

    Lu, Z. P.; Liu, C. T.; Thompson, J. R.; Porter, W. D.

    2004-06-01

    Recent advancement in bulk metallic glasses, whose properties are usually superior to their crystalline counterparts, has stimulated great interest in fabricating bulk amorphous steels. While a great deal of effort has been devoted to this field, the fabrication of structural amorphous steels with large cross sections has remained an alchemist’s dream because of the limited glass-forming ability (GFA) of these materials. Here we report the discovery of structural amorphous steels that can be cast into glasses with large cross-section sizes using conventional drop-casting methods. These new steels showed interesting physical, magnetic, and mechanical properties, along with high thermal stability. The underlying mechanisms for the superior GFA of these materials are discussed.

  7. Glass Stronger than Steel

    DOE R&D Accomplishments Database

    Yarris, Lynn

    2011-03-28

    A new type of damage-tolerant metallic glass, demonstrating a strength and toughness beyond that of steel or any other known material, has been developed and tested by a collaboration of researchers from Berkeley Lab and Caltech.

  8. Production of elemental sulfur and bentonite clay granules in a rotary drum

    NASA Astrophysics Data System (ADS)

    Hamilton, Ian Wallace

    Biological oxidation of sulfur granules is a critical component in elemental sulfur fertilizers since it converts sulfur to plant available sulfate. The level of biological oxidation is, in turn, regulated by the size and surface area of the sulfur granules. The aim of this research was to produce coarse sulfur granules that disintegrate to the correct particle size for biological oxidation, as well as the correct size for ballistic distribution from a spreader. Thus the interaction between mineral powders such as serpentine rock was investigated to get a better understanding of how these types of minerals react at different size fractions in granulation. Sulfur granules were developed from mixtures of 10% sodium bentonite clay with molten elemental sulfur. This was accomplished by sprayed a mixture bentonite and elemental sulfur into a falling curtain of fine material powder within a rotating drum. When comparing the seed materials, the serpentine rock showed sufficiently lower electrostatic build-up than phosphate rock. Serpentine rock also appears to help facilitate the disintegration of the granules when they are exposed to water. The outcome of the research was that it is possible to make a granulated sulfur fertilizer that had the correct size fraction and disintegration characteristics suitable for agronomic use.

  9. Post-prandial changes in protein synthesis in red drum (Sciaenops ocellatus) larvae.

    PubMed

    McCarthy, Ian D; Fuiman, Lee A

    2011-06-01

    Protein synthesis is one of the major energy-consuming processes in all living organisms. Post-prandial changes in protein synthesis have been studied in a range of animal taxa but have been little studied in fish larvae. Using the flooding-dose method, we measured post-prandial changes in whole-body rates of protein synthesis in regularly fed red drum Sciaenops ocellatus (Linnaeus) larvae for 24-28 h following their daily meal. Fractional rates of protein synthesis increased from a baseline (pre-feeding) rate of 16% day(-1) to a post-prandial peak of 48% day(-1) ca. 8 h after feeding before declining to 12% day(-1) after 24-28 h. The overall mean daily rate of protein synthesis was calculated as 27% day(-1). Although suggested as energetically impossible in larval poikilotherms, our results show that rates in excess of 30% day(-1) can be attained by larval fishes for a few hours but are not sustained. The average daily energetic cost of protein synthesis was estimated as 34% of daily total oxygen consumption, ranging from 19% immediately before feeding to 61% during the post-prandial peak in protein synthesis. This suggests that during the post-prandial peak, protein synthesis will require a large proportion of the hourly energy production, which, given the limited metabolic scope in fish larvae, may limit the energy that could otherwise be allocated to other energy-costly functions, such as foraging and escape responses.

  10. Maternal diet and larval diet influence survival skills of larval red drum Sciaenops ocellatus.

    PubMed

    Perez, K O; Fuiman, L A

    2015-04-01

    Larval red drum Sciaenops ocellatus survival, turning rate, routine swimming speed, escape response latency and escape response distance were significantly correlated with essential fatty-acid (EFA) concentrations in eggs. Of the five traits that varied with egg EFA content, two (escape response latency and routine swimming speed) were significantly different when larvae were fed enriched diets compared with the low fatty-acid diet, indicating that the larval diet can compensate for some imbalances in egg composition. Turning rate during routine swimming and escape response distance, however, did not change when larvae predicted to have low performance (based on egg composition) were fed an enriched diet, indicating that these effects of egg composition may be irreversible. Escape response distances and survival rates of larvae predicted to perform well (based on egg composition) and fed highly enriched diets were lower than expected, suggesting that high levels of EFA intake can be detrimental. Altogether, these results suggest that both maternal diet, which is responsible for egg EFA composition, and larval diet may play a role in larval survivorship and recruitment.

  11. Implementation of advanced matrix corrections for active interrogation of waste drums using the CTEN instrument

    SciTech Connect

    Melton, S.; Estep, R.; Hollas, C.

    1998-12-31

    The combined thermal/epithermal neutron instrument (CTEN) was designed at Los Alamos to improve measurement accuracy and mitigate self shielding effects inherent in the differential dieaway technique (DDT). A major goal in this research effort has been the development of a calibration technique that incorporates recently developed matrix and self-shielding corrections using data generated from additional detectors and new acquisition techniques. A comprehensive data set containing both active and passive measurements was generated using 26 different matrices and comprising a total of 1,400 measurements. In all, 31 flux-and-matrix-dependent parameters, 24 positional parameters, two dieaway times, and a correlated ratio were determined from each of the over 1,400 measurements. A reduced list of matrix indicators, prioritized using the alternating conditional expectation (ACE) algorithm, was used to train a neural network using a generalized regression technique (GRNN) to determine matrix- and position-corrected calibration factors. This paper describes the experimental, analytical, and empirical techniques used to determine the corrected calibration factor for an unknown waste drum. Results from a range of cases are compared with those obtained using a mobile DDT instrument and traditional DDT algorithms.

  12. Simultaneous Production of Amyloglucosidase and Exo-Polygalacturonase by Aspergillus niger in a Rotating Drum Reactor.

    PubMed

    Colla, Eliane; Santos, Lucielen Oliveira; Deamici, Kricelle; Magagnin, Glênio; Vendruscolo, Mauricio; Costa, Jorge Alberto Vieira

    2017-02-01

    Simultaneous production of amyloglucosidase (AMG) and exo-polygalacturonase (exo-PG) was carried out by Aspergillus niger in substrate of defatted rice bran in a rotating drum bioreactor (RDB) and studied by a 3(1) × 2(2) factorial experimental design. Variables under study were A. niger strains (A. niger NRRL 3122 and A. niger t0005/007-2), types of inoculum (spore suspension and fermented bran), and types of inducer (starch, pectin, and a mix of both). Solid-state fermentation process (SSF) was conducted at 30 °C under 60-vvm aeration for 96 h in a pilot scale. Production of AMG and exo-PG was significantly affected by the fungal strain and the type of inoculum, but inducers did not trigger any significant effect, an evidence of the fact that these enzymes are constitutive. The maximum activity of exo-PG was 84 U gdm(-1) whereas the maximum yield of AMG was 886.25 U gdm(-1).

  13. A perturbative approach to the spectral zeta functions of strings, drums, and quantum billiards

    SciTech Connect

    Amore, Paolo

    2012-12-15

    We show that the spectral zeta functions of inhomogeneous strings and drums can be calculated using Rayleigh-Schroedinger perturbation theory. The inhomogeneities that can be treated with this method are small but otherwise arbitrary and include the previously studied case of a piecewise constant density. In two dimensions the method can be used to derive the spectral zeta function of a domain obtained from the small deformation of a square. We also obtain exact sum rules that are valid for arbitrary densities and that correspond to the values taken by the spectral zeta function at integer positive values; we have tested numerically these sum rules in specific examples. We show that the Dirichlet or Neumann Casimir energies of an inhomogeneous string, evaluated to first order in perturbation theory, contain in some cases an irremovable divergence, but that the combination of the two is always free of divergences. Finally, our calculation of the Casimir energies of a string with piecewise constant density and of two perfectly conducting concentric cylinders, of similar radius, reproduce the results previously published.

  14. Hearing shapes of few electrons quantum drums: A configuration-interaction study

    NASA Astrophysics Data System (ADS)

    Ţolea, F.; Ţolea, M.

    2015-02-01

    The - highly remarkable - existence of non-congruent yet vibrationally isospectral shapes has been first proved theoretically and then also tested experimentally - by using electromagnetic waves in cavities, vibrating smectic films or electrons in nanostructures. In this context, we address the question whether isospectrality holds if two or more electrons interact electrostatically, using the accurate configuration-interaction method, in a discrete representation of the Bilby and Hawk shapes. Isospectral pairs offer an unique possibility to test how identical sets of single-particle energies may combine differently in the few-electrons eigenmodes, due to different wave functions spatial distributions. Our results point towards the break down of isospectrality in the presence of interactions. Thus one should be able to "hear" the shapes of few electrons quantum drums. Interestingly however, for the analyzed two and three electrons cases, there exists an interaction strength (which can be tuned by changing the size of the shapes), for which the ground states energies of Bilby and Hawk coincide, but not the excited states as well. Wigner localization is studied and shown to occur at about the same size for both Bilby and Hawk shapes. Next, an exercise is proposed to use the two-electrons charge density of the Bilby and Hawk ground states in the phase extraction scheme as proposed by Moon et al. (2008). Results show that out-of-phase regions appear if the linear size of the shapes exceeds the Bohr radius as occupation of higher Slater determinants becomes significant.

  15. Tertiary volcanic rocks and uranium in the Thomas Range and northern Drum Mountains, Juab County, Utah

    USGS Publications Warehouse

    Lindsey, David A.

    1982-01-01

    The Thomas Range and northern Drum Mountains have a history of volcanism, faulting, and mineralization that began about 42 m.y. (million years) ago. Volcanic activity and mineralization in the area can be divided into three stages according to the time-related occurrence of rock types, trace-element associations, and chemical composition of mineral deposits. Compositions of volcanic rocks changed abruptly from rhyodacite-quartz latite (42-39 m.y. ago) to rhyolite (38-32 m.y. ago) to alkali rhyolite (21 and 6-7 m.y. ago); these stages correspond to periods of chalcophile and siderophile metal mineralization, no mineralization(?), and lithophile metal mineralization, respectively. Angular unconformities record episodes of cauldron collapse and block faulting between the stages of volcanic activity and mineralization. The youngest angular unconformity formed between 21 and 7 m.y. ago during basin-and-range faulting. Early rhyodacite-quartz latite volcanism from composite volcanoes and fissures produced flows, breccias, and ash-flow tuff of the Drum Mountains Rhyodacite and Mt. Laird Tuff. Eruption of the Mt. Laird Tuff about 39 m.y. ago from an area north of Joy townsite was accompanied by collapse of the Thomas caldera. Part of the roof of the magma chamber did not collapse, or the magma was resurgent, as is indicated by porphyry dikes and plugs in the Drum Mountains. Chalcophile and siderophile metal mineralization, resulting in deposits of copper, gold, and manganese, accompanied early volcanism. Te middle stage of volcanic activity was characterized by explosive eruption of rhyolitic ash-flow tuffs and collapse of the Dugway Valley cauldron. Eruption of the Joy Tuff 38 m.y. ago was accompanied by subsidence of this cauldron and was followed by collapse and sliding of Paleozoic rocks from the west wall of the cauldron. Landslides in The Dell were covered by the Dell Tuff, erupted 32 m.y. ago from an unknown source to the east. An ash flow of the Needles Range

  16. Investigation of Cherenkov Light in an Oil Drum with Cosmic Radiation

    NASA Astrophysics Data System (ADS)

    Wedel, Zachary; Niduaza, Rexavalmar; Castro, Juan; Zavala, Favian; Fan, Sewan; Fatuzzo, Laura

    2014-03-01

    Photomultiplier Tubes (PMTs) have been around for decades and have become well understood in their use as cosmic ray detectors. Multi-Pixel Photon Counters (MPPCs), on the other hand, are still being explored as more viable, cost-effective light detector for counting cosmic rays. To detect cosmic rays by the Cherenkov effect, we placed an acrylic cylinder, with wavelength-shifting fibers coiled around it and filled with distilled water, inside a light-tight box that was able to detect the weak light signals with PMTs (1 and 3 inch), an MPPC (3 mm × 3 mm), and with coincidence between different detectors. Additionally, we utilized an oil drum with approximate volume of 30 gallons as a light-tight vessel to conduct coincidence counts for detecting cosmic rays using the PMTs and MPPCs (3 mm × 3 mm and 1 mm × 1 mm). In this poster presentation, we would present our findings as a comparative analysis between the two different vessels and the efficiency thereof of the same to determine whether or not the MPPC is a viable instrument for detecting cosmic rays that produce Cherenkov light. Department of Education grant number P031S90007.

  17. Metabolic requirements of red drum, Sciaenops ocellatus, for protein and energy based on weight gain and body composition.

    PubMed

    McGoogan, B B; Gatlin, D M

    1998-01-01

    Precise formulation of diets that meet but do not greatly exceed nutritional requirements should assist in lowering feed costs for commercial aquaculture of red drum, Sciaenops ocellatus. In this study, protein and energy requirements of red drum for maintenance and maximum gain were determined by feeding a diet containing digestible protein (DP) at 36.5% and 14.2 kJ digestible energy (DE) per gram at various rates for 8 wk in two separate experiments. Changes in weight and whole-body energy and protein were measured and regressed against protein or energy fed using a nonlinear procedure. In the first experiment, juvenile fish [ approximately 3. 4 g initial body weight (BW)] were either starved or fed at one of the following g/(100 g BW.d): 0.5, 1, 2, 4, 6, or 8. The second experiment utilized larger red drum (approximately 5.5 g initial weight), fed 0.75, 1.5, 3, 5, 5.5, 6, 6.5 or 7 g/(100 g BW.d) to confirm and refine results from the first experiment. Based on maintenance of body weight in both experiments, red drum had a protein maintenance requirement of 1.5 and 2.5 g DP/(kg BW.d) whereas estimates based on maintenance of whole-body protein were 0.5 and 2.2 g DP/(kg BW.d). Energy requirements for maintenance of weight and body energy ranged from 58 to 93 and 92 to 97 kJ DE/(kg BW.d), respectively. Protein requirements for maximum weight gain and change in body protein ranged from 20 to 25 g DP/(kg BW.d), whereas energy requirements for maximum weight gain and whole-body deposition ranged from 776 to 958 and 914 to 985 kJ DE/(kg BW.d), respectively. These requirements for maintenance and maximum gain of red drum should assist in formulation of diets for a variety of desired feeding strategies.

  18. Joining Steel Armor - Intermix

    DTIC Science & Technology

    1979-03-01

    TARADCOM a d ki Lk A el B~ 0el RWET0 TECHNICAL REPORT NO. 12311 JOINING STEEL ARMOR - INTERMIX March 1979 U U * S* ’ "U .by B. . A.SCEV * U...authorized documents. O "if TECHNICAL REPORT NO. 12311 JOINING STEEL ARMOR - INTERMIX BY B. A. SCHEVO March 1979 AMS: 3197..6D.4329 TARADCOM ARMOR AND...Intermix Process ...... ........ 3 Test Procedures - Intermix Armor ........ ......... 4 Mock Hull ................. ..................... 5 Results

  19. Life after Steel

    ERIC Educational Resources Information Center

    Mangan, Katherine

    2013-01-01

    Bobby Curran grew up in a working-class neighborhood in Baltimore, finished high school, and followed his grandfather's steel-toed bootprints straight to Sparrows Point, a 3,000-acre sprawl of industry on the Chesapeake Bay. College was not part of the plan. A gritty but well-paying job at the RG Steel plant was Mr. Curran's ticket to a secure…

  20. Ferrium M54 Steel

    DTIC Science & Technology

    2015-03-18

    15 to 18% (reference 1). Beyond this range the alloy becomes more noble than steel and loses its sacrificial protection property . Therefore, Zn-14...for a 7075-T651 aluminum alloy , which was subjected to biaxial fatigue loading in 3.5% NaCl solution (reference 27). NAWCADPAX/TIM-2014/292...Edition, Properties and Selection: Iron, Steels, and High- Performance Alloys , ASM International, 1990, p. 395. 8. G. L. Spencer and D. J. Duquette

  1. Articles comprising ferritic stainless steels

    SciTech Connect

    Rakowski, James M.

    2016-06-28

    An article of manufacture comprises a ferritic stainless steel that includes a near-surface region depleted of silicon relative to a remainder of the ferritic stainless steel. The article has a reduced tendency to form an electrically resistive silica layer including silicon derived from the steel when the article is subjected to high temperature oxidizing conditions. The ferritic stainless steel is selected from the group comprising AISI Type 430 stainless steel, AISI Type 439 stainless steel, AISI Type 441 stainless steel, AISI Type 444 stainless steel, and E-BRITE.RTM. alloy, also known as UNS 44627 stainless steel. In certain embodiments, the article of manufacture is a fuel cell interconnect for a solid oxide fuel cell.

  2. A modified stepping-stone model of population structure in red drum, Sciaenops ocellatus (Sciaenidae), from the northern Gulf of Mexico.

    PubMed

    Gold, J R; Burridge, C P; Turner, T F

    2001-01-01

    Genetic studies of population or 'stock' structure in exploited marine fishes typically are designed to determine whether geographic boundaries useful for conservation and management planning are identifiable. Implicit in many such studies is the notion that subpopulations or stocks, if they exist, have fixed territories with little or no gene exchange between them. Herein, we review our long-term genetic studies of red drum (Sciaenops ocellatus), an estuarine-dependent sciaenid fish in the Gulf of Mexico and western Atlantic Ocean. Significant differences in frequencies of mitochondrial DNA haplotypes and of alleles at nuclear-encoded microsatellites occur among red drum sampled across the northern Gulf of Mexico. The spatial distribution of the genetic variation, however, follows a pattern of isolation-by-distance consistent with the hypothesis that gene flow occurs among subpopulations and is an inverse (and continuous) function of geographic distance. However, successful reproduction and recruitment of red drum depend on estuarine habitats that have geographically discrete boundaries. We hypothesize that population structure in red drum follows a modified one-dimensional, linear stepping-stone model where gene exchange occurs primarily (but not exclusively) between adjacent bays and estuaries distributed linearly along the coastline. Gene flow does occur among estuaries that are not adjacent but probabilities of gene exchange decrease as a function of geographic distance. Implications of our hypothesis are discussed in terms of inferences drawn from patterns of isolation-by-distance and relative to conservation and management of estuarine-dependent species like red drum. Based on estimates of the ratio of genetic effective population size and census size in red drum, observed patterns of gene flow in red drum may play a significant role in recruitment.

  3. Exploring Shamanic Journeying: Repetitive Drumming with Shamanic Instructions Induces Specific Subjective Experiences but No Larger Cortisol Decrease than Instrumental Meditation Music

    PubMed Central

    Gingras, Bruno; Pohler, Gerald; Fitch, W. Tecumseh

    2014-01-01

    Exposure to repetitive drumming combined with instructions for shamanic journeying has been associated with physiological and therapeutic effects, such as an increase in salivary immunoglobulin A. In order to assess whether the combination of repetitive drumming and shamanic instructions is specifically associated with these effects, we compared the effect of listening to either repetitive drumming or instrumental meditation music for 15 minutes on salivary cortisol concentration and on self-reported physiological and psychological states. For each musical style, two groups of participants were exposed to two conditions: instructions for shamanic journeying or relaxation instructions. A total of 39 participants (24 females) inexperienced in shamanic journeying completed the experiment. Salivary cortisol concentrations were measured before and after exposure to music. In addition, participants filled out a mood questionnaire before and after the experiment and completed a post experiment questionnaire on their experiences. A significant decrease in the concentration in salivary cortisol was observed across all musical styles and instructions, indicating that exposure to 15 minutes of either repetitive drumming or instrumental meditation music, while lying down, was sufficient to induce a decrease in cortisol levels. However, no differences were observed across conditions. Significant differences in reported emotional states and subjective experiences were observed between the groups. Notably, participants exposed to repetitive drumming combined with shamanic instructions reported experiencing heaviness, decreased heart rate, and dreamlike experiences significantly more often than participants exposed to repetitive drumming combined with relaxation instructions. Our findings suggest that the subjective effects specifically attributed to repetitive drumming and shamanic journeying may not be reflected in differential endocrine responses. PMID:24999623

  4. View northwest, wharf A, sheet steel bulkhead, steel lift tower ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View northwest, wharf A, sheet steel bulkhead, steel lift tower - U.S. Coast Guard Sandy Hook Station, Western Docking Structure, West of intersection of Canfield Road & Hartshorne Drive, Highlands, Monmouth County, NJ

  5. Characterization of 618-11 solid waste burial ground, disposed waste, and description of the waste generating facilities

    SciTech Connect

    Hladek, K.L.

    1997-10-07

    The 618-11 (Wye or 318-11) burial ground received transuranic (TRTJ) and mixed fission solid waste from March 9, 1962, through October 2, 1962. It was then closed for 11 months so additional burial facilities could be added. The burial ground was reopened on September 16, 1963, and continued operating until it was closed permanently on December 31, 1967. The burial ground received wastes from all of the 300 Area radioactive material handling facilities. The purpose of this document is to characterize the 618-11 solid waste burial ground by describing the site, burial practices, the disposed wastes, and the waste generating facilities. This document provides information showing that kilogram quantities of plutonium were disposed to the drum storage units and caissons, making them transuranic (TRU). Also, kilogram quantities of plutonium and other TRU wastes were disposed to the three trenches, which were previously thought to contain non-TRU wastes. The site burial facilities (trenches, caissons, and drum storage units) should be classified as TRU and the site plutonium inventory maintained at five kilograms. Other fissile wastes were also disposed to the site. Additionally, thousands of curies of mixed fission products were also disposed to the trenches, caissons, and drum storage units. Most of the fission products have decayed over several half-lives, and are at more tolerable levels. Of greater concern, because of their release potential, are TRU radionuclides, Pu-238, Pu-240, and Np-237. TRU radionuclides also included slightly enriched 0.95 and 1.25% U-231 from N-Reactor fuel, which add to the fissile content. The 618-11 burial ground is located approximately 100 meters due west of Washington Nuclear Plant No. 2. The burial ground consists of three trenches, approximately 900 feet long, 25 feet deep, and 50 feet wide, running east-west. The trenches constitute 75% of the site area. There are 50 drum storage units (five 55-gallon steel drums welded together

  6. Hyperventilation and blood acid-base balance in hypercapnia exposed red drum (Sciaenops ocellatus).

    PubMed

    Ern, Rasmus; Esbaugh, Andrew J

    2016-05-01

    Hyperventilation is a common response in fish exposed to elevated water CO2. It is believed to lessen the respiratory acidosis associated with hypercapnia by lowering arterial PCO2, but the contribution of hyperventilation to blood acid-base compensation has yet to be quantified. Hyperventilation may also increase the flux of irons across the gill epithelium and the cost of osmoregulation, owing to the osmo-respiratory compromise. Therefore, hypercapnia exposed fish may increase standard metabolic rate (SMR) leaving less energy for physiological functions such as foraging, migration, growth and reproduction. Here we show that gill ventilation, blood PCO2 and total blood [CO2] increased in red drum (Sciaenops ocellatus) exposed to 1000 and 5000 µatm water CO2, and that blood PCO2 and total blood [CO2] decrease in fish during hypoxia induced hyperventilation. Based on these results we estimate the ventilatory contributions to total acid-base compensation in 1000 and 5000 µatm water CO2. We find that S. ocellatus only utilize a portion of its ventilatory capacity to reduce the acid-base disturbance in 1000 µatm water CO2. SMR was unaffected by both salinity and hypercapnia exposure indicating that the cost of osmoregulation is small relative to SMR, and that the lack of increased ventilation in 1000 µatm water CO2 despite the capacity to do so is not due to an energetic tradeoff between acid-base balance and osmoregulation. Therefore, while ocean acidification may impact ventilatory parameters, there will be little impact on the overall energy budget of S. ocellatus.

  7. Comparison of Fenton's reagent and adsorption for treatment of industrial container and drum cleaning industry wastewater.

    PubMed

    Güneş, Elçin; Çifçi, Deniz İzlen; Çelik, Suna Özden

    2017-03-27

    The present study is aimed to explore the characterization of Industrial Container and Drum Cleaning (ICDC) industry wastewater and treatment alternatives of this wastewater using Fenton and adsorption processes. Wastewater derived from ICDC industry is usually treated by chemical coagulation and biological treatment in Turkey and then discharged in a centralized wastewater treatment facility. It is required that the wastewater COD is below 1500 mg/L to treat in a centralized wastewater treatment facility The wastewater samples characterized for parameters of pH, conductivity, COD, BOD5, TSS, NH3-N, TN, TOC, TP, Cd, Cr, Cu, Fe, Ni, Pb, Zn, Hg. Optimum conditions of adsorption and Fenton processes have been assessed in terms of COD removal. Initial COD values were quite high in the three of samples and were in the range of 11300-14200 mg/L. The optimum conditions were as follows for Fenton treatment; 35-40 g/L for H2O2, 2-5 g/L for Fe(2+) and 13-36 for H2O2/Fe(2+) molar ratio. The optimum conditions of PAC doses and contact times in adsorption studies were 20-30 g/L and 5-12 hours respectively. In terms of COD removal, the efficiency of the Fenton process was found to be about 91-97%, and the efficiency of the adsorption process was found to be 88-98%. COD, BOD5, TOC, TP, Cd, Cr, Cu, Fe, Ni, Pb, Zn and Hg removal efficiencies were compared for both Fenton and adsorption processes under optimum conditions for the three samples. The results suggest that these wastewaters are suitable for discharge to a centralized wastewater treatment plant.

  8. Heat and water transfer in a rotating drum containing solid substrate particles.

    PubMed

    Schutyser, M A I; Weber, F J; Briels, W J; Rinzema, A; Boom, R M

    2003-06-05

    In previous work we reported on the simulation of mixing behavior of a slowly rotating drum for solid-state fermentation (SSF) using a discrete particle model. In this investigation the discrete particle model is extended with heat and moisture transfer. Heat transfer is implemented in the model via interparticle contacts and the interparticle heat transfer coefficient is determined experimentally. The model is shown to accurately predict heat transfer and resulting temperature gradients in a mixed wheat grain bed. In addition to heat transfer, the addition and subsequent distribution of water in the substrate bed is also studied. The water is added to the bed via spray nozzles to overcome desiccation of the bed during evaporative cooling. The development of moisture profiles in the bed during spraying and mixing are studied experimentally with a water-soluble fluorescent tracer. Two processes that affect the water distribution are considered in the model: the intraparticle absorption process, and the interparticle transfer of free water. It is found that optimum distribution can be achieved when the free water present at the surface of the grains is quickly distributed in the bed, for example, by fast mixing. Alternatively, a short spraying period, followed by a period of mixing without water addition, can be applied. The discrete particle model developed is used successfully to examine the influence of process operation on the moisture distribution (e.g., fill level and rotation rate). It is concluded that the extended discrete particle model can be used as a powerful predictive tool to derive operating strategies and criteria for design and scale-up for mixed SSF and other processes with granular media.

  9. Superclean steel development

    SciTech Connect

    Richman, R.H.; McNaughton, W.P. )

    1989-12-01

    The Electric Power Research Institute has actively encouraged and sponsored a number of research projects to develop a superclean 3.5NiCrMoV steel for low pressure turbine rotors. Such steel is highly resistant to temper embrittlement and will thus facilitate increased efficiency in electricity generation through the use of higher operating temperatures and improvements in design. The objective of this interim report was to integrate the results that have been generated to date worldwide in the pursuit of superclean steel. The report contains detailed findings that enable the interested utility to evaluate how the results affect utility decision making. A companion document has been written to summarize the findings from this technical report. The results indicate that steels with impurity contents typical of the superclean specification can be manufactured for production rotors with properties that equal or exceed those for conventional 3.5NiCrMoV rotors in every detail. Of particular interest are the results that the superclean steels appear to be virtually resistant to temper embrittlement to a temperature of 500 {degrees}C. 109 refs., 51 figs., 9 tabs.

  10. Trends in steel technology. [Dual phase and HSLA steels

    SciTech Connect

    Not Available

    1980-01-01

    Dual phase steels, composite products, and microalloyed steels are making inroads in the automotive industry applications for bumpers, automotive parts, bodies, mechanical parts, suspension and steering equipment and truck bumpers. New steels are also used to support solar mirrors and cells, in corrosive environments in the oil and gas industry, fusion reactors, and pressure vessels in nuclear power plants. (FS)

  11. Quarter-scale modeling of room convergence effects on CH (contact-handled) TRU drum waste emplacements using WIPP (Waste Isolation Pilot Plant) reference design geometries

    SciTech Connect

    VandeKraats, J.

    1987-11-01

    This study investigates the effect of horizontal room convergence on CH waste packages emplaced in the WIPP Reference Design geometry (rooms 13 feet high by 33 feet wide, with minus 3/8 inch screened backfill emplaced over and around the waste packages) as a function of time. Based on two tests, predictions were made with regard to full-scale 6-packs emplaced in the Reference Design geometry. These are that load will be transmitted completely through the stack within the first five years after waste emplacement and all drums in all 6-packs will be affected; that virtually all drums will show some deformation eight years after emplacement; that some drums may breach before the eighth year after emplacement has elapsed; and that based on criteria developed during testing, it is predicted that 1% of the drums emplaced will be breached after 8 years and, after 15 years, approximately 12% of the drums are predicted to be breached. 8 refs., 41 figs., 3 tabs.

  12. Device for preventing damage to a submarine cable at the point where it leaves an equipment casing during passage round the cable drum and over the davit

    SciTech Connect

    Guazzo, L.; Vives, J.P.

    1984-11-06

    A device for preventing damage to a submarine cable at the point where it leaves an equipment casing during passage round the cable drum and over the davit, and consisting of a chocking member on each side of the casing surrounding the cable from its outlet from the casing to a point of contact of the cable with the drum, said chocking member being in the form of a body of revolution about the cable axis of generally pear-shaped configuration when unstressed and having a swollen part at the casing end, said chocking member occupying all the space between the cable and the drum when the cable is wound on the drum, the swollen part of the chocking member when unstressed having a radius at least equal to the distance between the cable and the drum at the outlet from the casing. The chocking member may be a sleeve of a strong and flexible material; it may also consist of a stack of elementary chocking members.

  13. Description of the U.S. Geological Survey`s slug-tests at the Hallam Nuclear Facility, July to November 1994

    SciTech Connect

    1995-01-19

    An aquifer test agreement between the US Department of Energy (USDOE) and the US Geological Survey (USGS) was set up to log and measure the aquifer response in two observation wells, IB and 4C at the Hallam Nuclear Facility, Hallam, Nebraska. Observation wells 1B and 4C are owned by the USDOE and were installed by HWS Technologies Inc. of Lincoln, Nebraska, in June 1993. These observation wells were measured monthly from September 1993 to August 1994 by using a graduated steel tape. The accuracy of these water-level measurements is approximately {plus_minus}0.02 foot. Also well 1B contained a submersible pressure transducer to record hourly water-level data during this same period. During access of the wells, personnel wear clean disposable latex gloves, a hard hat, and safety glasses. Directly following each measurement the steel-tape was rinsed with deionized water and the effluent was disposed of in a 55-gallon drum. For the aquifer tests, observation wells 1B and 4C had submersible pressure transducers installed to monitor water-level responses. These pressure transducers were connected to an electronic data logger (edl) to record the water levels, atmospheric pressure from a barometric pressure gauge, and rainfall data from a tipping-bucket rain gauge. The data recorded on each edl was downloaded onto a field computer during each site visit, processed in the field, and then stored on the USGS`s Data General workstations upon return to the District Office.

  14. Continuous steel production and apparatus

    DOEpatents

    Peaslee, Kent D.; Peter, Jorg J.; Robertson, David G. C.; Thomas, Brian G.; Zhang, Lifeng

    2009-11-17

    A process for continuous refining of steel via multiple distinct reaction vessels for melting, oxidation, reduction, and refining for delivery of steel continuously to, for example, a tundish of a continuous caster system, and associated apparatus.

  15. Stainless steel tanks

    SciTech Connect

    Hagen, T.

    1995-12-31

    There is currently no recognized code or standard for the design, fabrication and construction of atmospheric and low pressure stainless steel tanks. At the present time these tanks are being designed to individual specifications, manufacturers standards or utilizing other codes and standards that may not be entirely applicable. Recognizing the need, the American Petroleum Institute will be publishing a new appendix to the API STD 650 Standard which will cover stainless steel tanks. The new Appendix was put together by a Task Group of selected individuals from the API Subcommittee of Pressure Vessels and Tanks from the Committee on Refinery Equipment. This paper deals with the development and basis of the new appendix. The new appendix will provide a much needed standard to cover the material, design, fabrication, erection and testing requirements for vertical, cylindrical, austenitic stainless steel aboveground tanks in nonrefrigerated service.

  16. A-3 steel work completed

    NASA Technical Reports Server (NTRS)

    2009-01-01

    Stennis Space Center engineers celebrated a key milestone in construction of the A-3 Test Stand on April 9 - completion of structural steel work. Workers with Lafayette (La.) Steel Erector Inc. placed the last structural steel beam atop the stand during a noon ceremony attended by more than 100 workers and guests.

  17. Growth and protein metabolism in red drum (Sciaenops ocellatus) larvae exposed to environmental levels of atrazine and malathion.

    PubMed

    McCarthy, Ian D; Fuiman, Lee A

    2008-07-30

    Contaminant exposure can affect development, growth, and behaviour of fish larvae, but its effect on rates of protein synthesis and protein degradation are not known. The aim of the present study was to examine the effects of a single pulsed dose aqueous exposure to environmentally realistic levels of two contaminants, atrazine (0, 40 and 80 microgl(-1)) and malathion (0, 1 and 10 microgl(-1)), on growth and protein synthesis in red drum (Sciaenops ocellatus) larvae. Growth was assessed in terms of increase in length, weight, and protein content over an 8-day period following exposure. Rates of protein synthesis were measured by the flooding dose technique 2, 4, and 8 days after initial exposure to each contaminant by bathing larvae in seawater containing L-[2,6-(3)H] phenylalanine. Exposure to atrazine had no effect on larval growth in length, but caused marginally significant declines in growth in weight (P=0.05) and protein content (P=0.06). However, protein synthesis rates were significantly higher for atrazine-exposed larvae on days 4 (P=0.04) and 8 (P=0.01), suggesting an increase in rates of protein degradation. On day 8, the efficiency with which synthesised proteins contributed to growth was significantly lower (P=0.04) in atrazine-exposed larvae. In contrast, malathion had no significant effects on growth in length or protein content, but there were significant decreases in growth in weight over 8 days. The only other significant effect of malathion was an increase in protein synthesis on day 2 for treated larvae relative to controls. Previous work [Alvarez, M.C., Fuiman, L.A., 2005. Environmental levels of atrazine and its degradation products impair survival skills and growth of red drum larvae. Aquat. Toxicol. 74, 229-241] reported hyperactivity and increased metabolic rate in larval red drum exposed to atrazine, indicating a clear energetic cost. Our results further emphasise the energetic cost of atrazine exposure through elevated rates of protein

  18. Microbial-Influenced Corrosion of Corten Steel Compared with Carbon Steel and Stainless Steel in Oily Wastewater by Pseudomonas aeruginosa

    NASA Astrophysics Data System (ADS)

    Mansouri, Hamidreza; Alavi, Seyed Abolhasan; Fotovat, Meysam

    2015-07-01

    The microbial corrosion behavior of three important steels (carbon steel, stainless steel, and Corten steel) was investigated in semi petroleum medium. This work was done in modified nutrient broth (2 g nutrient broth in 1 L oily wastewater) in the presence of Pseudomonas aeruginosa and mixed culture (as a biotic media) and an abiotic medium for 2 weeks. The behavior of corrosion was analyzed by spectrophotometric and electrochemical methods and at the end was confirmed by scanning electron microscopy. The results show that the degree of corrosion of Corten steel in mixed culture, unlike carbon steel and stainless steel, is less than P. aeruginosa inoculated medium because some bacteria affect Corten steel less than other steels. According to the experiments, carbon steel had less resistance than Corten steel and stainless steel. Furthermore, biofilm inhibits separated particles of those steels to spread to the medium; in other words, particles get trapped between biofilm and steel.

  19. Temporal genetic variation of mitochondrial DNA and the female effective population size of red drum (Sciaenops ocellatus) in the northern Gulf of Mexico.

    PubMed

    1999-07-01

    We studied genetic drift of mitochondrial DNA (mtDNA) haplotype frequencies in a natural population of red drum (Sciaenops ocellatus) from the northern Gulf of Mexico (Gulf). The amount of genetic drift observed across temporally adjacent year classes (1986-89) was used to estimate variance effective (female) population size (Nef). Nef was estimated to be 14 308 and the ratio of female effective size to adult female census size was approximately 0.004, which is among the lowest value reported for vertebrate animals. Low effective size relative to census size among red drum in the northern Gulf may result from yearly fluctuations in the number of breeding females, high variance in female reproductive success, or both. Despite low genetic effective size relative to census size, the genetic effective population size of red drum in the northern Gulf appears sufficiently large to preclude potentially deleterious effects of inbreeding.

  20. A trade-off between sexual signalling and immune function in a natural population of the drumming wolf spider Hygrolycosa rubrofasciata.

    PubMed

    Ahtiainen, J J; Alatalo, R V; Kortet, R; Rantala, M J

    2005-07-01

    The field of ecological immunology is ultimately seeking to address the question 'Why is there variation in immune function?' Here, we provide experimental evidence that costs of ubiquitous sexual signals are a significant source of variation in immune function. In the mating season, males of the wolf spider Hygrolycosa rubrofasciata drum against dry leaves while wandering around the habitat searching for receptive females. According to a previous study, the male metabolic rate during the drumming increases 22-fold compared to the resting metabolic rate. In the present study, we examined whether investment in costly courtship drumming decreases male immune function in a wild population of H. rubrofasciata. We induced males to increase their drumming rate by introducing females in proximity. As estimates of male immune function, we used lytic activity and encapsulation rate. Lytic activity estimates the concentration of antimicrobial peptides in haemolymph, which have been shown to play an important role in defence against bacteria, viruses and fungi. Encapsulation is an important defence mechanism against nematodes and insect parasitoids, but it also plays a role in defence against viruses. Our results show that males with nonarbitrarily increased investment in drumming rate had considerably lower lytic activities than control males. Also, there was a tendency for males with nonarbitrarily increased investment in drumming rate to have lower encapsulation rates than control males. This study provides experimental evidence for the first time, to our knowledge, that there are direct immunological costs of sexual signalling in natural populations. Therefore, immunological costs of sexual signals may provide significant phenotypic variation to parasite-mediated sexual selection.