Science.gov

Sample records for 640x480 image details

  1. 17 μm pixel 640 x 480 microbolometer FPA development at BAE Systems

    NASA Astrophysics Data System (ADS)

    Blackwell, Richard J.; Bach, Tuyet; O'Donnell, Dan; Geneczko, Jeannie; Joswick, Michael

    2007-04-01

    BAE Systems has developed an advanced 640 x 480 focal plane array (FPA) with a 17 μm pixel pitch. Sensitivity of <= 50 mK was demonstrated and the FPAs were used in imaging demonstrations. Successful scaling of BAE Systems' patented single contact per pixel, single-level microbolometer process to 17 μm pitch provides a path toward next generation microbolometer imaging systems.

  2. DRS U6000 640x480 VOx uncooled IR focal plane

    NASA Astrophysics Data System (ADS)

    Howard, Philip E.; Clarke, John E.; Ionescu, Adrian C.; Li, Chuan C.; Stevens, John C.

    2002-08-01

    DRS (formerly Boeing) has completed the development and demonstration of a 25-micron pixel size 640x480 VOx microbolometer uncooled IR focal plane product, the U6000. The U6000 incorporates several advanced features to enhance its performance and functional capabilities. A parallel six- bit Smart-Sensor data bus provides external command and data interface capability between the sensor and the focal plane. This includes on chip 6-bit pixel offset correction, detector bias selection and regulation, programmable signal gain, interlaced and non-interlaced output video format selection, signal integration time selection and input referred global offset selection capabilities. The U6000 also includes a high resolution on-chip temperature measurement that is incorporated into the single channel output video during horizontal blanking. This paper describes the U6000's functional capabilities, and provides U6000 functional validation and performance data.

  3. 320x240 and 640x480 UFPAs for TWS and DVE applications

    NASA Astrophysics Data System (ADS)

    Han, C. J.; Rawlings, Richard; Sweeney, Mike; Whicker, Steve; Peysha, Doug; Clarke, J. Elwood; Sullivan, Bill; Li, Chuan; Howard, Phillip

    2005-05-01

    DRS Technologies has designed and delivered Thermal Weapon Site (TWS) and Driver's Viewer Enhancer (DVE) system using its U3500 (320x240) and U6000 (640x480) 1-mil detector arrays. The detectors are modified to enhance its manufacturability, thermal time constant, package life time, and its reliability under shock and vibration to meet TWS and DVE requirements. The U6000 array operates at 30 Hz frame rate with NETD less than 50 mK normalized to F/1.0 optics. At a saving to the system weight and power, these arrays operate from -40°C to +65°C without the aid of a TE cooler. This is accomplished through a combination of sensor calibration and smart ROIC architecture.

  4. 640 x 480 pixel uncooled infrared FPA with SOI diode detectors

    NASA Astrophysics Data System (ADS)

    Ueno, Masashi; Kosasayama, Yasuhiro; Sugino, Takaki; Nakaki, Yoshiyuki; Fujii, Yoshio; Inoue, Hiromoto; Kama, Keisuke; Seto, Toshiki; Takeda, Munehisa; Kimata, Masafumi

    2005-05-01

    This paper describes the structure and performance of a 25-micron pitch 640 x 480 pixel uncooled infrared focal plane array (IR FPA) with silicon-on-insulator (SOI) diode detectors. The uncooled IR FPA is a thermal type FPA that has a temperature sensor of single crystal PN junction diodes formed in an SOI layer. In the conventional pixel structure, the temperature sensor and two support legs for thermal isolation are made in the lower level of the pixel, and an IR absorbing structure is made in the upper pixel level to cover almost the entire pixel area. The IR absorption utilizes IR reflections from the lower level. Since the reflection from the support leg portions is not perfect due to the slits in the metal reflector, the reflection becomes smaller as the support leg section increases in reduced pixel pitches. In order to achieve high thermal isolation and high IR absorption simultaneously, we have developed a new pixel structure that has an independent IR reflector between the lower and upper levels. The structure assures perfect IR reflection and thus improves IR absorption. The FPA shows a noise equivalent temperature difference (NETD) of 40 mK (f/1.0) and a responsivity non-uniformity of less than 0.9%. The good uniformity is due to the high uniformity of the electrical characteristics of SOI diodes made of single crystal silicon (Si). We have confirmed that the SOI diodes architecture is suitable for large format uncooled IR FPAs.

  5. Design, fabrication and testing of 17um pitch 640x480 uncooled infrared focal plane array detector

    NASA Astrophysics Data System (ADS)

    Jiang, Lijun; Liu, Haitao; Chi, Jiguang; Qian, Liangshan; Pan, Feng; Liu, Xiang

    2015-10-01

    Uncooled infrared focal plane array (UIRFPA) detectors are widely used in industrial thermography cameras, night vision goggles, thermal weapon sights, as well as automotive night vision systems. To meet the market requirement for smaller pixel pitch and higher resolution, we have developed a 17um pitch 640x480 UIRFPA detector. The detector is based on amorphous silicon (a-Si) microbolometer technology, the readout integrated circuit (ROIC) is designed and manufactured with 0.35um standard CMOS technology on 8 inch wafer, the microbolometer is fabricated monolithically on the ROIC using an unique surface micromachining process developed inside the company, the fabricated detector is vacuum packaged with hermetic metal package and tested. In this paper we present the design, fabrication and testing of the 17um 640x480 detector. The design trade-off of the detector ROIC and pixel micro-bridge structure will be discussed, by comparison the calculation and simulation to the testing results. The novel surface micromachining process using silicon sacrificial layer will be presented, which is more compatible with the CMOS process than the traditional process with polyimide sacrificial layer, and resulted in good processing stability and high fabrication yield. The performance of the detector is tested, with temperature equivalent temperature difference (NETD) less than 60mK at F/1 aperture, operability better than 99.5%. The results demonstrate that the detector can meet the requirements of most thermography and night vision applications.

  6. Uncooled thermal imaging sensor and application advances

    NASA Astrophysics Data System (ADS)

    Norton, Peter W.; Cox, Stephen; Murphy, Bob; Grealish, Kevin; Joswick, Mike; Denley, Brian; Feda, Frank; Elmali, Loriann; Kohin, Margaret

    2006-05-01

    BAE Systems continues to advance the technology and performance of microbolometer-based thermal imaging modules and systems. 640x480 digital uncooled infrared focal plane arrays are in full production, illustrated by recent production line test data for two thousand focal plane arrays. This paper presents a snapshot of microbolometer technology at BAE Systems and an overview of two of the most important thermal imaging sensor programs currently in production: a family of thermal weapons sights for the United States Army and a thermal imager for the remote weapons station on the Stryker vehicle.

  7. Most Detailed Image of the Crab Nebula

    NASA Technical Reports Server (NTRS)

    2005-01-01

    This new Hubble image -- one among the largest ever produced with the Earth-orbiting observatory -- shows the most detailed view so far of the entire Crab Nebula ever made. The Crab is arguably the single most interesting object, as well as one of the most studied, in all of astronomy. The image is the largest image ever taken with Hubble's WFPC2 workhorse camera.

    The Crab Nebula is one of the most intricately structured and highly dynamical objects ever observed. The new Hubble image of the Crab was assembled from 24 individual exposures taken with the NASA/ESA Hubble Space Telescope and is the highest resolution image of the entire Crab Nebula ever made.

  8. HUBBLE CAPTURES DETAILED IMAGE OF URANUS' ATMOSPHERE

    NASA Technical Reports Server (NTRS)

    2002-01-01

    Hubble Space Telescope has peered deep into Uranus' atmosphere to see clear and hazy layers created by a mixture of gases. Using infrared filters, Hubble captured detailed features of three layers of Uranus' atmosphere. Hubble's images are different from the ones taken by the Voyager 2 spacecraft, which flew by Uranus 10 years ago. Those images - not taken in infrared light - showed a greenish-blue disk with very little detail. The infrared image allows astronomers to probe the structure of Uranus' atmosphere, which consists of mostly hydrogen with traces of methane. The red around the planet's edge represents a very thin haze at a high altitude. The haze is so thin that it can only be seen by looking at the edges of the disk, and is similar to looking at the edge of a soap bubble. The yellow near the bottom of Uranus is another hazy layer. The deepest layer, the blue near the top of Uranus, shows a clearer atmosphere. Image processing has been used to brighten the rings around Uranus so that astronomers can study their structure. In reality, the rings are as dark as black lava or charcoal. This false color picture was assembled from several exposures taken July 3, 1995 by the Wide Field Planetary Camera-2. CREDIT: Erich Karkoschka (University of Arizona Lunar and Planetary Lab) and NASA

  9. Hubble Captures Detailed Image of Uranus' Atmosphere

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Hubble Space Telescope has peered deep into Uranus' atmosphere to see clear and hazy layers created by a mixture of gases. Using infrared filters, Hubble captured detailed features of three layers of Uranus' atmosphere.

    Hubble's images are different from the ones taken by the Voyager 2 spacecraft, which flew by Uranus 10 years ago. Those images - not taken in infrared light - showed a greenish-blue disk with very little detail.

    The infrared image allows astronomers to probe the structure of Uranus' atmosphere, which consists of mostly hydrogen with traces of methane. The red around the planet's edge represents a very thin haze at a high altitude. The haze is so thin that it can only be seen by looking at the edges of the disk, and is similar to looking at the edge of a soap bubble. The yellow near the bottom of Uranus is another hazy layer. The deepest layer, the blue near the top of Uranus, shows a clearer atmosphere.

    Image processing has been used to brighten the rings around Uranus so that astronomers can study their structure. In reality, the rings are as dark as black lava or charcoal.

    This false color picture was assembled from several exposures taken July 3, 1995 by the Wide Field Planetary Camera-2.

    The Wide Field/Planetary Camera 2 was developed by the Jet Propulsion Laboratory and managed by the Goddard Spaced Flight Center for NASA's Office of Space Science.

    This image and other images and data received from the Hubble Space Telescope are posted on the World Wide Web on the Space Telescope Science Institute home page at URL http://oposite.stsci.edu/pubinfo/

  10. Research on the Hotel Image Based on the Detail Service

    NASA Astrophysics Data System (ADS)

    Li, Ban; Shenghua, Zheng; He, Yi

    Detail service management, initially developed as marketing programs to enhance customer loyalty, has now become an important part of customer relation strategy. This paper analyzes the critical factors of detail service and its influence on the hotel image. We establish the theoretical model of influencing factors on hotel image and propose corresponding hypotheses. We use applying statistical method to test and verify the above-mentioned hypotheses. This paper provides a foundation for further study of detail service design and planning issues.

  11. 13. LOOKING NORTH FROM THE SOUTH, A DETAIL IMAGE OF ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    13. LOOKING NORTH FROM THE SOUTH, A DETAIL IMAGE OF THE BRONZE DEDICATION PLAQUE, LOCATED ON THE NORTH INSIDE PARAPET. A TWIN PLAQUE ON THE SOUTHWEST PARAPET. - Seventh Street Bridge, Spanning Haw Creek at Seventh Street, Columbus, Bartholomew County, IN

  12. System design of the CRISM (compact reconnaissance imaging spectrometer for Mars) hyperspectral imager

    NASA Astrophysics Data System (ADS)

    Silverglate, Peter R.; Fort, Dennis E.

    2004-01-01

    CRISM (Compact Reconnaissance Imaging Spectrometer for Mars) is a hyperspectral imager that will be launched on the MRO (Mars Reconnaissance Orbiter) in August 2005. The MRO will circle Mars in a polar orbit at a nominal altitude of 325 km. The CRISM spectral range spans the ultraviolet (UV) to the mid-wave infrared (MWIR), 400 nm to 4050 nm. The instrument utilizes a Ritchey-Chretien telescope with a 2.06º field of view (FOV) to focus light on the entrance slit of a dual spectrometer. Within the spectrometer light is split by a dichroic into VNIR (visible-near infrared) (λ <= 1.05 μm) and IR (infrared) (λ >= 1.05 μm) beams. Each beam is directed into a separate modified Offner spectrometer that focuses a spectrally dispersed image of the slit onto a two dimensional focal plane (FP). The IR FP is a 640 x 480 HgCdTe area array; the VNIR FP is a 640 x 480 silicon photodiode area array. The spectral image is contiguously sampled with a 6.55 nm spectral spacing and an instantaneous field of view of 60 μradians. The orbital motion of the MRO pushbroom scans the spectrometer slit across the Martian surface, allowing the planet to be mapped in 558 spectral bands. There are four major mapping modes: A quick initial multi-spectral mapping of a major portion of the Martian surface in 59 selected spectral bands at a spatial resolution of 600 μradians (10:1 binning); an extended multi-spectral mapping of the entire Martian surface in 59 selected spectral bands at a spatial resolution of 300 μradians (5:1 binning); a high resolution Target Mode, performing hyperspectral mapping of selected targets of interest at full spatial and spectral resolution; and an atmospheric Emission Phase Function (EPF) mode for atmospheric study and correction at full spectral resolution at a spatial resolution of 300 μradians (5:1 binning). The instrument is gimbaled to allow scanning over +/-60° for the EPF and Target modes. The scanning also permits orbital motion compensation, enabling

  13. System design of the CRISM (compact reconnaissance imaging spectrometer for Mars) hyperspectral imager

    NASA Astrophysics Data System (ADS)

    Silverglate, Peter R.; Fort, Dennis E.

    2003-12-01

    CRISM (Compact Reconnaissance Imaging Spectrometer for Mars) is a hyperspectral imager that will be launched on the MRO (Mars Reconnaissance Orbiter) in August 2005. The MRO will circle Mars in a polar orbit at a nominal altitude of 325 km. The CRISM spectral range spans the ultraviolet (UV) to the mid-wave infrared (MWIR), 400 nm to 4050 nm. The instrument utilizes a Ritchey-Chretien telescope with a 2.06º field of view (FOV) to focus light on the entrance slit of a dual spectrometer. Within the spectrometer light is split by a dichroic into VNIR (visible-near infrared) (λ <= 1.05 μm) and IR (infrared) (λ >= 1.05 μm) beams. Each beam is directed into a separate modified Offner spectrometer that focuses a spectrally dispersed image of the slit onto a two dimensional focal plane (FP). The IR FP is a 640 x 480 HgCdTe area array; the VNIR FP is a 640 x 480 silicon photodiode area array. The spectral image is contiguously sampled with a 6.55 nm spectral spacing and an instantaneous field of view of 60 μradians. The orbital motion of the MRO pushbroom scans the spectrometer slit across the Martian surface, allowing the planet to be mapped in 558 spectral bands. There are four major mapping modes: A quick initial multi-spectral mapping of a major portion of the Martian surface in 59 selected spectral bands at a spatial resolution of 600 μradians (10:1 binning); an extended multi-spectral mapping of the entire Martian surface in 59 selected spectral bands at a spatial resolution of 300 μradians (5:1 binning); a high resolution Target Mode, performing hyperspectral mapping of selected targets of interest at full spatial and spectral resolution; and an atmospheric Emission Phase Function (EPF) mode for atmospheric study and correction at full spectral resolution at a spatial resolution of 300 μradians (5:1 binning). The instrument is gimbaled to allow scanning over +/-60° for the EPF and Target modes. The scanning also permits orbital motion compensation, enabling

  14. Detail enhancement of blurred infrared images based on frequency extrapolation

    NASA Astrophysics Data System (ADS)

    Xu, Fuyuan; Zeng, Deguo; Zhang, Jun; Zheng, Ziyang; Wei, Fei; Wang, Tiedan

    2016-05-01

    A novel algorithm for enhancing the details of the blurred infrared images based on frequency extrapolation has been raised in this paper. Unlike other researchers' work, this algorithm mainly focuses on how to predict the higher frequency information based on the Laplacian pyramid separation of the blurred image. This algorithm uses the first level of the high frequency component of the pyramid of the blurred image to reverse-generate a higher, non-existing frequency component, and adds back to the histogram equalized input blurred image. A simple nonlinear operator is used to analyze the extracted first level high frequency component of the pyramid. Two critical parameters are participated in the calculation known as the clipping parameter C and the scaling parameter S. The detailed analysis of how these two parameters work during the procedure is figure demonstrated in this paper. The blurred image will become clear, and the detail will be enhanced due to the added higher frequency information. This algorithm has the advantages of computational simplicity and great performance, and it can definitely be deployed in the real-time industrial applications. We have done lots of experiments and gave illustrations of the algorithm's performance in this paper to convince its effectiveness.

  15. Hyperspectral imaging with a liquid crystal polarization interferometer.

    PubMed

    Hegyi, Alex; Martini, Joerg

    2015-11-01

    A novel hyperspectral imaging system has been developed that takes advantage of the tunable path delay between orthogonal polarization states of a liquid crystal variable retarder. The liquid crystal is placed in the optical path of an imaging system and the path delay between the polarization states is varied, causing an interferogram to be generated simultaneously at each pixel. A data set consisting of a series of images is recorded while varying the path delay; Fourier transforming the data set with respect to the path delay yields the hyperspectral data-cube. The concept is demonstrated with a prototype imager consisting of a liquid crystal variable retarder integrated into a commercial 640x480 pixel CMOS camera. The prototype can acquire a full hyperspectral data-cube in 0.4 s, and is sensitive to light over a 400 nm to 1100 nm range with a dispersion-dependent spectral resolution of 450 cm(-1) to 660 cm(-1). Similar to Fourier transform spectroscopy, the imager is spatially and spectrally multiplexed and therefore achieves high optical throughput. Additionally, the common-path nature of the polarization interferometer yields a vibration-insensitive device. Our concept allows for the spectral resolution, imaging speed, and spatial resolution to be traded off in software to optimally address a given application. The simplicity, compactness, potential low cost, and software adaptability of the device may enable a disruptive class of hyperspectral imaging systems with a broad range of applications. PMID:26561143

  16. Design of a fiber optic image transmission link

    NASA Astrophysics Data System (ADS)

    Redd, Justin D.

    1991-12-01

    An original design is presented for a fiber optic based digital image transmission link operating at a serial bit rate of 250 Mbits/Second. The link is designed as an integral part of an airborne infrared imaging system with particular emphasis on avoiding problems associated with aircraft electromagnetic interference (EMI). Unique features include simplicity (single PC board transmitter and receiver), low power, low cost (under $3,000), and use of the latest off-the-shelf components (including the Gazelle GA9011/GA9012 HOT ROD chip set). Theoretical modeling is used to predict a bit error rate of better than 10 to the minus 15th power, while actual measurements include transmission of over 10 to 13th power bits without any errors (measured bit error rate of at least 10 to the minus 13th power). Test results also show that the link is capable of transmitting 640 x 480 pixel (12 bits per pixel) images with no significant image degradation.

  17. A texture-based architecture for face detection in IR images on an FPGA

    NASA Astrophysics Data System (ADS)

    Vergara, Marcelo; Wolf, Alejandro; Figueroa, Miguel

    2014-10-01

    This paper presents a digital architecture for face detection on infrared (IR) images. We use Local Binary Patterns (LBP) to build a feature vector for each pixel, which represents the texture of the image in a vicinity of that pixel. We use a Support Vector Machine (SVM), trained with 306 images of 51 different subjects, to recognize human face textures. Finally, we group the classified pixels into rectangular boxes enclosing the faces using an algorithm for connected components. These boxes can then be used to track, count, or identify faces in a scene, for example. We implemented our architecture on a Xilinx XC6SLX45 FPGA and tested it on 306 IR images of 51 subjects, different from the data used to train the SVM. The circuit correctly identifies 100% of the faces in the images, and reports 4.5% of false positives. We also tested the system on a set of IR video streams featuring multiple faces per image, with varied poses and backgrounds, and obtained a hit rate of 94.5%, with 7.2% false positives. The circuit uses less than 25% of the logic resources available on the FPGA, and can process 313 640x480-pixel images per second with a 100MHz clock, while consuming 266mW of power.

  18. Segmenting texts from outdoor images taken by mobile phones using color features

    NASA Astrophysics Data System (ADS)

    Liu, Zongyi; Zhou, Hanning

    2011-01-01

    Recognizing texts from images taken by mobile phones with low resolution has wide applications. It has been shown that a good image binarization can substantially improve the performances of OCR engines. In this paper, we present a framework to segment texts from outdoor images taken by mobile phones using color features. The framework consists of three steps: (i) the initial process including image enhancement, binarization and noise filtering, where we binarize the input images in each RGB channel, and apply component level noise filtering; (ii) grouping components into blocks using color features, where we compute the component similarities by dynamically adjusting the weights of RGB channels, and merge groups hierachically, and (iii) blocks selection, where we use the run-length features and choose the Support Vector Machine (SVM) as the classifier. We tested the algorithm using 13 outdoor images taken by an old-style LG-64693 mobile phone with 640x480 resolution. We compared the segmentation results with Tsar's algorithm, a state-of-the-art camera text detection algorithm, and show that our algorithm is more robust, particularly in terms of the false alarm rates. In addition, we also evaluated the impacts of our algorithm on the Abbyy's FineReader, one of the most popular commercial OCR engines in the market.

  19. Imaging polarimetry in the LWIR with microgrid polarimeters

    NASA Astrophysics Data System (ADS)

    Tyo, J. S.

    2010-06-01

    Microgrid polarimeters have emerged over the past decade as a viable tool for performing real-time, highly accurate polarimetric imagery. A microgrid polarimeter operates by integrating a focal plane array (FPA) with an array of micropolarizing optics. Mircrogrids have the advantage of being relatively compact, rugged, and inherently spatiotemporally aligned. However, they have the single disadvantage that the various polarization measurements that go into estimating the Stokes parameters at a particular pixel are actually coming from separate locations in the field. Hence, a microgrid polarimeter performs best where there is no image information, obviating the need for an imaging polarimeter! Recently we have been working with a LWIR microgrid polarimeter at the College of Optical Sciences. Our instrument is a DRS Sensors & Targeting Systems 640 x 480 HgCdTe FPA with linear polarizers at 0°, 45°, 90°, and 135° [1]. In this paper we will review our recent results that derive methods for artifact-free reconstruction of band limited imagery.

  20. Digital image fusion systems: color imaging and low-light targets

    NASA Astrophysics Data System (ADS)

    Estrera, Joseph P.

    2009-05-01

    This paper presents digital image fusion (enhanced A+B) systems in color imaging and low light target applications. This paper will discuss first the digital sensors that are utilized in the noted image fusion applications which is a 1900x1086 (high definition format) CMOS imager coupled to a Generation III image intensifier for the visible/near infrared (NIR) digital sensor and 320x240 or 640x480 uncooled microbolometer thermal imager for the long wavelength infrared (LWIR) digital sensor. Performance metrics for these digital imaging sensors will be presented. The digital image fusion (enhanced A+B) process will be presented in context of early fused night vision systems such as the digital image fused system (DIFS) and the digital enhanced night vision goggle and later, the long range digitally fused night vision sighting system. Next, this paper will discuss the effects of user display color in a dual color digital image fusion system. Dual color image fusion schemes such as Green/Red, Cyan/Yellow, and White/Blue for image intensifier and thermal infrared sensor color representation, respectively, are discussed. Finally, this paper will present digitally fused imagery and image analysis of long distance targets in low light from these digital fused systems. The result of this image analysis with enhanced A+B digital image fusion systems is that maximum contrast and spatial resolution is achieved in a digital fusion mode as compared to individual sensor modalities in low light, long distance imaging applications. Paper has been cleared by DoD/OSR for Public Release under Ref: 08-S-2183 on August 8, 2008.

  1. Stereoscopic uncooled thermal imaging with autostereoscopic 3D flat-screen display in military driving enhancement systems

    NASA Astrophysics Data System (ADS)

    Haan, H.; Münzberg, M.; Schwarzkopf, U.; de la Barré, R.; Jurk, S.; Duckstein, B.

    2012-06-01

    Thermal cameras are widely used in driver vision enhancement systems. However, in pathless terrain, driving becomes challenging without having a stereoscopic perception. Stereoscopic imaging is a well-known technique already for a long time with understood physical and physiological parameters. Recently, a commercial hype has been observed, especially in display techniques. The commercial market is already flooded with systems based on goggle-aided 3D-viewing techniques. However, their use is limited for military applications since goggles are not accepted by military users for several reasons. The proposed uncooled thermal imaging stereoscopic camera with a geometrical resolution of 640x480 pixel perfectly fits to the autostereoscopic display with a 1280x768 pixels. An eye tracker detects the position of the observer's eyes and computes the pixel positions for the left and the right eye. The pixels of the flat panel are located directly behind a slanted lenticular screen and the computed thermal images are projected into the left and the right eye of the observer. This allows a stereoscopic perception of the thermal image without any viewing aids. The complete system including camera and display is ruggedized. The paper discusses the interface and performance requirements for the thermal imager as well as for the display.

  2. Cloud Imagers Offer New Details on Earth's Health

    NASA Technical Reports Server (NTRS)

    2009-01-01

    A stunning red sunset or purple sunrise is an aesthetic treat with a scientific explanation: The colors are a direct result of the absorption or reflectance of solar radiation by atmospheric aerosols, minute particles (either solid or liquid) in the Earth s atmosphere that occur both naturally and because of human activity. At the beginning or end of the day, the Sun s rays travel farther through the atmosphere to reach an observer s eyes and more green and yellow light is scattered, making the Sun appear red. Sunset and sunrise are especially colorful when the concentration of atmospheric particles is high. This ability of aerosols to absorb and reflect sunlight is not just pretty; it also determines the amount of radiation and heat that reaches the Earth s surface, and can profoundly affect climate. In the atmosphere, aerosols are also important as nuclei for the condensation of water droplets and ice crystals. Clouds with fewer aerosols cannot form as many water droplets (called cloud particles), and consequently, do not scatter light well. In this case, more sunlight reaches the Earth s surface. When aerosol levels in clouds are high, however, more nucleation points can form small liquid water droplets. These smaller cloud particles can reflect up to 90 percent of visible radiation to space, keeping the heat from ever reaching Earth s surface. The tendency for these particles to absorb or reflect the Sun s energy - called extinction by astronomers - depends on a number of factors, including chemical composition and the humidity and temperature in the surrounding air; because cloud particles are so small, they are affected quickly by minute changes in the atmosphere. Because of this sensitivity, atmospheric scientists study cloud particles to anticipate patterns and shifts in climate. Until recently, NASA s study of atmospheric aerosols and cloud particles has been focused primarily on satellite images, which, while granting large-scale atmospheric analysis

  3. A new imaging technique on strength and phase of pulsatile tissue-motion in brightness-mode ultrasonogram

    NASA Astrophysics Data System (ADS)

    Fukuzawa, Masayuki; Yamada, Masayoshi; Nakamori, Nobuyuki; Kitsunezuka, Yoshiki

    2007-03-01

    A new imaging technique has been developed for observing both strength and phase of pulsatile tissue-motion in a movie of brightness-mode ultrasonogram. The pulsatile tissue-motion is determined by evaluating the heartbeat-frequency component in Fourier transform of a series of pixel value as a function of time at each pixel in a movie of ultrasonogram (640x480pixels/frame, 8bit/pixel, 33ms/frame) taken by a conventional ultrasonograph apparatus (ATL HDI5000). In order to visualize both the strength and the phase of the pulsatile tissue-motion, we propose a pulsatile-phase image that is obtained by superimposition of color gradation proportional to the motion phase on the original ultrasonogram only at which the motion strength exceeds a proper threshold. The pulsatile-phase image obtained from a cranial ultrasonogram of normal neonate clearly reveals that the motion region gives good agreement with the anatomical shape and position of the middle cerebral artery and the corpus callosum. The motion phase is fluctuated with the shape of arteries revealing local obstruction of blood flow. The pulsatile-phase images in the neonates with asphyxia at birth reveal decreases of the motion region and increases of the phase fluctuation due to the weakness and local disturbance of blood flow, which is useful for pediatric diagnosis.

  4. Interaction of image noise, spatial resolution, and low contrast fine detail preservation in digital image processing

    NASA Astrophysics Data System (ADS)

    Artmann, Uwe; Wueller, Dietmar

    2009-01-01

    We present a method to improve the validity of noise and resolution measurements on digital cameras. If non-linear adaptive noise reduction is part of the signal processing in the camera, the measurement results for image noise and spatial resolution can be good, while the image quality is low due to the loss of fine details and a watercolor like appearance of the image. To improve the correlation between objective measurement and subjective image quality we propose to supplement the standard test methods with an additional measurement of the texture preserving capabilities of the camera. The proposed method uses a test target showing white Gaussian noise. The camera under test reproduces this target and the image is analyzed. We propose to use the kurtosis of the derivative of the image as a metric for the texture preservation of the camera. Kurtosis is a statistical measure for the closeness of a distribution compared to the Gaussian distribution. It can be shown, that the distribution of digital values in the derivative of the image showing the chart becomes the more leptokurtic (increased kurtosis) the stronger the noise reduction has an impact on the image.

  5. DETAILED DECOMPOSITION OF GALAXY IMAGES. II. BEYOND AXISYMMETRIC MODELS

    SciTech Connect

    Peng, Chien Y.; Ho, Luis C.; Impey, Chris D.; Rix, Hans-Walter E-mail: lho@obs.carnegiescience.ed E-mail: rix@mpia-hd.mpg.d

    2010-06-15

    We present a two-dimensional (2D) fitting algorithm (GALFIT, ver. 3) with new capabilities to study the structural components of galaxies and other astronomical objects in digital images. Our technique improves on previous 2D fitting algorithms by allowing for irregular, curved, logarithmic and power-law spirals, ring, and truncated shapes in otherwise traditional parametric functions like the Sersic, Moffat, King, Ferrer, etc., profiles. One can mix and match these new shape features freely, with or without constraints, and apply them to an arbitrary number of model components of numerous profile types, so as to produce realistic-looking galaxy model images. Yet, despite the potential for extreme complexity, the meaning of the key parameters like the Sersic index, effective radius, or luminosity remains intuitive and essentially unchanged. The new features have an interesting potential for use to quantify the degree of asymmetry of galaxies, to quantify low surface brightness tidal features beneath and beyond luminous galaxies, to allow more realistic decompositions of galaxy subcomponents in the presence of strong rings and spiral arms, and to enable ways to gauge the uncertainties when decomposing galaxy subcomponents. We illustrate these new features by way of several case studies that display various levels of complexity.

  6. Hundred metre virtual telescope captures unique detailed colour image

    NASA Astrophysics Data System (ADS)

    2009-02-01

    A team of French astronomers has captured one of the sharpest colour images ever made. They observed the star T Leporis, which appears, on the sky, as small as a two-storey house on the Moon [1]. The image was taken with ESO's Very Large Telescope Interferometer (VLTI), emulating a virtual telescope about 100 metres across and reveals a spherical molecular shell around an aged star. ESO PR Photo 06a/09 The star T Leporis as seen with VLTI ESO PR Photo 06b/09 The star T Leporis to scale ESO PR Photo 06c/09 A virtual 100-metre telescope ESO PR Photo 06d/09 The orbit of Theta1 Orionis C ESO PR Video 06a/09 Zoom-in onto T Leporis "This is one of the first images made using near-infrared interferometry," says lead author Jean-Baptiste Le Bouquin. Interferometry is a technique that combines the light from several telescopes, resulting in a vision as sharp as that of a giant telescope with a diameter equal to the largest separation between the telescopes used. Achieving this requires the VLTI system components to be positioned to an accuracy of a fraction of a micrometre over about 100 metres and maintained so throughout the observations -- a formidable technical challenge. When doing interferometry, astronomers must often content themselves with fringes, the characteristic pattern of dark and bright lines produced when two beams of light combine, from which they can model the physical properties of the object studied. But, if an object is observed on several runs with different combinations and configurations of telescopes, it is possible to put these results together to reconstruct an image of the object. This is what has now been done with ESO's VLTI, using the 1.8-metre Auxiliary Telescopes. "We were able to construct an amazing image, and reveal the onion-like structure of the atmosphere of a giant star at a late stage of its life for the first time," says Antoine Mérand, member of the team. "Numerical models and indirect data have allowed us to imagine the

  7. Tomographic brain imaging with nucleolar detail and automatic cell counting

    PubMed Central

    Hieber, Simone E.; Bikis, Christos; Khimchenko, Anna; Schweighauser, Gabriel; Hench, Jürgen; Chicherova, Natalia; Schulz, Georg; Müller, Bert

    2016-01-01

    Brain tissue evaluation is essential for gaining in-depth insight into its diseases and disorders. Imaging the human brain in three dimensions has always been a challenge on the cell level. In vivo methods lack spatial resolution, and optical microscopy has a limited penetration depth. Herein, we show that hard X-ray phase tomography can visualise a volume of up to 43 mm3 of human post mortem or biopsy brain samples, by demonstrating the method on the cerebellum. We automatically identified 5,000 Purkinje cells with an error of less than 5% at their layer and determined the local surface density to 165 cells per mm2 on average. Moreover, we highlight that three-dimensional data allows for the segmentation of sub-cellular structures, including dendritic tree and Purkinje cell nucleoli, without dedicated staining. The method suggests that automatic cell feature quantification of human tissues is feasible in phase tomograms obtained with isotropic resolution in a label-free manner. PMID:27581254

  8. Tomographic brain imaging with nucleolar detail and automatic cell counting.

    PubMed

    Hieber, Simone E; Bikis, Christos; Khimchenko, Anna; Schweighauser, Gabriel; Hench, Jürgen; Chicherova, Natalia; Schulz, Georg; Müller, Bert

    2016-01-01

    Brain tissue evaluation is essential for gaining in-depth insight into its diseases and disorders. Imaging the human brain in three dimensions has always been a challenge on the cell level. In vivo methods lack spatial resolution, and optical microscopy has a limited penetration depth. Herein, we show that hard X-ray phase tomography can visualise a volume of up to 43 mm(3) of human post mortem or biopsy brain samples, by demonstrating the method on the cerebellum. We automatically identified 5,000 Purkinje cells with an error of less than 5% at their layer and determined the local surface density to 165 cells per mm(2) on average. Moreover, we highlight that three-dimensional data allows for the segmentation of sub-cellular structures, including dendritic tree and Purkinje cell nucleoli, without dedicated staining. The method suggests that automatic cell feature quantification of human tissues is feasible in phase tomograms obtained with isotropic resolution in a label-free manner. PMID:27581254

  9. Super Resolution Reconstruction Based on Adaptive Detail Enhancement for ZY-3 Satellite Images

    NASA Astrophysics Data System (ADS)

    Zhu, Hong; Song, Weidong; Tan, Hai; Wang, Jingxue; Jia, Di

    2016-06-01

    Super-resolution reconstruction of sequence remote sensing image is a technology which handles multiple low-resolution satellite remote sensing images with complementary information and obtains one or more high resolution images. The cores of the technology are high precision matching between images and high detail information extraction and fusion. In this paper puts forward a new image super resolution model frame which can adaptive multi-scale enhance the details of reconstructed image. First, the sequence images were decomposed into a detail layer containing the detail information and a smooth layer containing the large scale edge information by bilateral filter. Then, a texture detail enhancement function was constructed to promote the magnitude of the medium and small details. Next, the non-redundant information of the super reconstruction was obtained by differential processing of the detail layer, and the initial super resolution construction result was achieved by interpolating fusion of non-redundant information and the smooth layer. At last, the final reconstruction image was acquired by executing a local optimization model on the initial constructed image. Experiments on ZY-3 satellite images of same phase and different phase show that the proposed method can both improve the information entropy and the image details evaluation standard comparing with the interpolation method, traditional TV algorithm and MAP algorithm, which indicate that our method can obviously highlight image details and contains more ground texture information. A large number of experiment results reveal that the proposed method is robust and universal for different kinds of ZY-3 satellite images.

  10. Gaussian mixture model-based gradient field reconstruction for infrared image detail enhancement and denoising

    NASA Astrophysics Data System (ADS)

    Zhao, Fan; Zhao, Jian; Zhao, Wenda; Qu, Feng

    2016-05-01

    Infrared images are characterized by low signal-to-noise ratio and low contrast. Therefore, the edge details are easily immerged in the background and noise, making it much difficult to achieve infrared image edge detail enhancement and denoising. This article proposes a novel method of Gaussian mixture model-based gradient field reconstruction, which enhances image edge details while suppressing noise. First, by analyzing the gradient histogram of noisy infrared image, Gaussian mixture model is adopted to simulate the distribution of the gradient histogram, and divides the image information into three parts corresponding to faint details, noise and the edges of clear targets, respectively. Then, the piecewise function is constructed based on the characteristics of the image to increase gradients of faint details and suppress gradients of noise. Finally, anisotropic diffusion constraint is added while visualizing enhanced image from the transformed gradient field to further suppress noise. The experimental results show that the method possesses unique advantage of effectively enhancing infrared image edge details and suppressing noise as well, compared with the existing methods. In addition, it can be used to effectively enhance other types of images such as the visible and medical images.

  11. Novel image detail enhancement technology for high dynamic range infrared detector

    NASA Astrophysics Data System (ADS)

    Liu, Ning; Zhu, Caigao

    2014-11-01

    In this paper, we propose a novel image detail enhancement technology which is well solved the problem of how to suppress the noise and enhance the detail at the same time of the infrared image. This technology is based on the layer separation idea. In nowadays, this idea is studied by many researchers, and many detail enhancement algorithms have been come up through this idea such as the bilateral filter for detail enhancement. According to our research, these algorithms although have the advantages of enhancing the detail without enhancing the noise, they also have the disadvantages of massive calculation, low speed and the worst is the gradient flipping effect which cause the enhanced image distorted. Our solution is based on the Guided Image Filter (GIF) to deal the separated detail layer of an image. The gradient flipping effect will be greatly suppressed with the priority that the GIF is a linear filter. Which means that the processed image will become much closer to the original image. We determine an adaptive weighting coefficient as the filter kernel. After that, we compress the base component into the display range by our modified histogram projection and enhance the detail component using the gain mask of the filter weighting coefficient. At last, we recombine the two parts and quantize the result to 8-bit domain. Experimental verification and detailed realization have been provided in this paper. We also have done significant comparison between our method and the proposed algorithm to show the superiority of our algorithm.

  12. High dynamic range infrared images detail enhancement based on local edge preserving filter

    NASA Astrophysics Data System (ADS)

    Song, Qiong; Wang, Yuehuan; Bai, Kun

    2016-07-01

    In the field of infrared (IR) image processing, displaying a high dynamic range (HDR) image on a low dynamic range display equipment with a natural visual effect, clear details on local areas and less artifacts is an important issue. In this paper, we present a new approach to display HDR IR images with contrast enhancement. First, the local edge-preserving filter (LEPF) is utilized to separate the image into a base layer and detail layer(s). After the filtering procedure, we use an adaptive Gamma transformation to adjust the gray distribution of the base layer, and stretch the detail layer based on a human visual effect principle. Then, we recombine the detail layer and base layer to obtain the enhance output. Finally, we adjust the luminance of output by applying multiple exposure fusion method. The experimental results demonstrate that our proposed method can provide a significant performance in terms of enhancing details and less artifacts than the state of the arts.

  13. Infrared image detail enhancement approach based on improved joint bilateral filter

    NASA Astrophysics Data System (ADS)

    Liu, Ning; Chen, Xiaohong

    2016-07-01

    In this paper, we proposed a new infrared image detail enhancement approach. This approach could not only achieve the goal of enhancing the digital detail, but also make the processed image much closer to the real situation. Inspired by the joint-bilateral filter, two adjacent images were utilized to calculate the kernel functions in order to distinguish the detail information from the raw image. We also designed a new kernel function to modify the joint-bilateral filter and to eliminate the gradient reversal artifacts caused by the non-linear filtering. The new kernel is based on an adaptive emerge coefficient to realize the detail layer determination. The detail information was modified by the adaptive emerge coefficient along with two key parameters to realize the detail enhancement. Finally, we combined the processed detail layer with the base layer and rearrange the high dynamic image into monitor-suited low dynamic range to achieve better visual effect. Numerical calculation showed that this new technology has the best value compare to the previous research in detail enhancement. Figures and data flowcharts were demonstrated in the paper.

  14. Research of detecting details and features of infrared polarization imaging experiment

    NASA Astrophysics Data System (ADS)

    Yang, Fan; Liu, Xiao-cheng; Wang, Ji-zhong

    2013-09-01

    Along with modern infrared camouflage technique developed, it is hard to distinguish target and background by using traditional infrared intensity imaging in general because infrared feature of target and background are tending to consistent. To address this issue, a thought that utilizes infrared polarization imaging technique to detect target is proposed in this paper based on analyzing of the principle of infrared polarization imaging. The experiments are carried out for detecting of infrared low-contrast target imaging. Comparing with the infrared intensity images, the average gradient of the infrared polarization image has been improved 155% and the contrast of target and background has been improved 120% in infrared polarization images. The effective experimental data and imaging law between infrared polarization images and infrared intensity images are obtained that, the technology of infrared polarization imaging can detect details of infrared target more clearly than the infrared intensity imaging, and it can obviously increase the contrast between target and background. Therefore, it is more helpful to detecting details and features of target.

  15. Selectively detail-enhanced fusion of differently exposed images with moving objects.

    PubMed

    Li, Zhengguo; Zheng, Jinghong; Zhu, Zijian; Wu, Shiqian

    2014-10-01

    In this paper, we introduce an exposure fusion scheme for differently exposed images with moving objects. The proposed scheme comprises a ghost removal algorithm in a low dynamic range domain and a selectively detail-enhanced exposure fusion algorithm. The proposed ghost removal algorithm includes a bidirectional normalization-based method for the detection of nonconsistent pixels and a two-round hybrid method for the correction of nonconsistent pixels. Our detail-enhanced exposure fusion algorithm includes a content adaptive bilateral filter, which extracts fine details from all the corrected images simultaneously in gradient domain. The final image is synthesized by selectively adding the extracted fine details to an intermediate image that is generated by fusing all the corrected images via an existing multiscale algorithm. The proposed exposure fusion algorithm allows fine details to be exaggerated while existing exposure fusion algorithms do not provide such an option. The proposed scheme usually outperforms existing exposure fusion schemes when there are moving objects in real scenes. In addition, the proposed ghost removal algorithm is simpler than existing ghost removal algorithms and is suitable for mobile devices with limited computational resource. PMID:25148667

  16. Application of high-resolution stereo satellite images to detailed landslide hazard assessment

    NASA Astrophysics Data System (ADS)

    Nichol, Janet E.; Shaker, Ahmed; Wong, Man-Sing

    2006-06-01

    This study investigates and demonstrates the state of the art in remote sensing techniques for detailed landslide hazard assessment applicable to large areas. Since the most common methods of landslide hazard assessment using simple inventories and weighted overlays are heavily dependent on three-dimensional terrain visualization and analysis, stereo satellite images from the IKONOS Very High Resolution (VHR) sensor are used for this study. The DEMs created from IKONOS stereo images appear to be much more accurate and sensitive to micro-scale terrain features than a DEM created from digital contour data with a 2 m contour interval. Pan-sharpened stereo IKONOS images permit interpretation of recent landslides as small as 2-3 m in width as well as relict landslides older than 50 years. A cost-benefit analysis comparing stereo air photo interpretation with stereo satellite image interpretation suggests that stereo satellite imagery is usually more cost-effective for detailed landslide hazard assessment over large areas.

  17. Investigating the visual inspection subjectivity on the contrast-detail evaluation in digital mammography images

    NASA Astrophysics Data System (ADS)

    Sousa, Maria A. Z.; Medeiros, Regina B.; Schiabel, Homero

    2014-03-01

    A major difficulty in the interpretation of mammographic images is the low contrast and, in the case of early detection of breast cancer, the reduced size of the features of malignancy on findings such as microcalcifications. Furthermore, image assessment is subject to significant reliance of the capacity of observation of the expert that will perform it, compromising the final diagnosis accuracy. Thinking about this aspect, this study evaluated the subjectivity of visual inspection to assess the contrast-detail in mammographic images. For this, we compared the human readings of images generated with the CDMAM phantom performed by four observers, enabling to determining a threshold of contrast visibility in each diameter disks present in the phantom. These thresholds were compared graphically and by statistical measures allowing us to build a strategy for use of contrast and detail (dimensions) as parameters of quality in mammography.

  18. Low-cost microsensors program

    NASA Astrophysics Data System (ADS)

    Anderson, John S.; Bradley, Daryl; Chen, Chungte W.; Chin, Richard; Hegg, Ronald G.; Kennedy, Adam; Murphy, Daniel F.; Ray, Michael; Wyles, Richard; Brown, James C.; Newsome, Gwendolyn W.

    2002-07-01

    The Low Cost Microsensors (LCMS) Program recently demonstrated state-of-the-art imagery in a long-range infrared (IR) sensor built upon an uncooled vanadium oxide (VOx) 640 X 480 format focal plane array (FPA) engine. The 640 X 480 sensor is applicable to long-range surveillance and targeting missions. The intent of this DUS&T effort is to further reduce the cost, weight, and power of uncooled IR sensors, and to increase the capability of these sensors, thereby expanding their applicability to military and commercial markets never before addressed by thermal imaging.

  19. Maia X-ray fluorescence imaging: Capturing detail in complex natural samples

    NASA Astrophysics Data System (ADS)

    Ryan, C. G.; Siddons, D. P.; Kirkham, R.; Li, Z. Y.; de Jonge, M. D.; Paterson, D. J.; Kuczewski, A.; Howard, D. L.; Dunn, P. A.; Falkenberg, G.; Boesenberg, U.; De Geronimo, G.; Fisher, L. A.; Halfpenny, A.; Lintern, M. J.; Lombi, E.; Dyl, K. A.; Jensen, M.; Moorhead, G. F.; Cleverley, J. S.; Hough, R. M.; Godel, B.; Barnes, S. J.; James, S. A.; Spiers, K. M.; Alfeld, M.; Wellenreuther, G.; Vukmanovic, Z.; Borg, S.

    2014-04-01

    Motivated by the challenge of capturing complex hierarchical chemical detail in natural material from a wide range of applications, the Maia detector array and integrated realtime processor have been developed to acquire X-ray fluorescence images using X-ray Fluorescence Microscopy (XFM). Maia has been deployed initially at the XFM beamline at the Australian Synchrotron and more recently, demonstrating improvements in energy resolution, at the P06 beamline at Petra III in Germany. Maia captures fine detail in element images beyond 100 M pixels. It combines a large solid-angle annular energy-dispersive 384 detector array, stage encoder and flux counter inputs and dedicated FPGA-based real-time event processor with embedded spectral deconvolution. This enables high definition imaging and enhanced trace element sensitivity to capture complex trace element textures and place them in a detailed spatial context. Maia hardware and software methods provide per pixel correction for dwell, beam flux variation, dead-time and pileup, as well as off-line parallel processing for enhanced throughput. Methods have been developed for real-time display of deconvoluted SXRF element images, depth mapping of rare particles and the acquisition of 3D datasets for fluorescence tomography and XANES imaging using a spectral deconvolution method that tracks beam energy variation.

  20. CRISM (Compact Reconnaissance Imaging Spectrometer for Mars) on MRO (Mars Reconnaissance Orbiter)

    NASA Astrophysics Data System (ADS)

    Murchie, Scott L.; Arvidson, Raymond E.; Bedini, Peter; Beisser, K.; Bibring, Jean-Pierre; Bishop, J.; Boldt, John D.; Choo, Tech H.; Clancy, R. Todd; Darlington, Edward H.; Des Marais, D.; Espiritu, R.; Fasold, Melissa J.; Fort, Dennis; Green, Richard N.; Guinness, E.; Hayes, John R.; Hash, C.; Heffernan, Kevin J.; Hemmler, J.; Heyler, Gene A.; Humm, David C.; Hutchison, J.; Izenberg, Noam R.; Lee, Robert E.; Lees, Jeffrey J.; Lohr, David A.; Malaret, Erick R.; Martin, T.; Morris, Richard V.; Mustard, John F.; Rhodes, Edgar A.; Robinson, Mark S.; Roush, Ted L.; Schaefer, Edward D.; Seagrave, Gordon G.; Silverglate, Peter R.; Slavney, S.; Smith, Mark F.; Strohbehn, Kim; Taylor, Howard W.; Thompson, Patrick L.; Tossman, Barry E.

    2004-12-01

    CRISM (Compact Reconnaissance Imaging Spectrometer for Mars) is a hyperspectral imager that will be launched on the MRO (Mars Reconnaissance Orbiter) spacecraft in August 2005. MRO"s objectives are to recover climate science originally to have been conducted on the Mars Climate Orbiter (MCO), to identify and characterize sites of possible aqueous activity to which future landed missions may be sent, and to characterize the composition, geology, and stratigraphy of Martian surface deposits. MRO will operate from a sun-synchronous, near-circular (255x320 km altitude), near-polar orbit with a mean local solar time of 3 PM. CRISM"s spectral range spans the ultraviolet (UV) to the mid-wave infrared (MWIR), 383 nm to 3960 nm. The instrument utilizes a Ritchey-Chretien telescope with a 2.12° field-of-view (FOV) to focus light on the entrance slit of a dual spectrometer. Within the spectrometer, light is split by a dichroic into VNIR (visible-near-infrared, 383-1071 nm) and IR (infrared, 988-3960 nm) beams. Each beam is directed into a separate modified Offner spectrometer that focuses a spectrally dispersed image of the slit onto a two dimensional focal plane (FP). The IR FP is a 640 x 480 HgCdTe area array; the VNIR FP is a 640 x 480 silicon photodiode area array. The spectral image is contiguously sampled with a 6.6 nm spectral spacing and an instantaneous field of view of 61.5 μradians. The Optical Sensor Unit (OSU) can be gimbaled to take out along-track smear, allowing long integration times that afford high signal-to-noise ratio (SNR) at high spectral and spatial resolution. The scan motor and encoder are controlled by a separately housed Gimbal Motor Electronics (GME) unit. A Data Processing Unit (DPU) provides power, command and control, and data editing and compression. CRISM acquires three major types of observations of the Martian surface and atmosphere. In Multispectral Mapping Mode, with the gimbal pointed at planet nadir, data are collected at frame rates

  1. A patch-based cross masking model for natural images with detail loss and additive defects

    NASA Astrophysics Data System (ADS)

    Liu, Yucheng; Allebach, Jan P.

    2015-03-01

    Visual masking is an effect that contents of the image reduce the detectability of a given target signal hidden in the image. The effect of visual masking has found its application in numerous image processing and vision tasks. In the past few decades, numerous research has been conducted on visual masking based on models optimized for artificial targets placed upon unnatural masks. Over the years, there is a tendency to apply masking model to predict natural image quality and detection threshold of distortion presented in natural images. However, to our knowledge few studies have been conducted to understand the generalizability of masking model to different types of distortion presented in natural images. In this work, we measure the ability of natural image patches in masking three different types of distortion, and analyse the performance of conventional gain control model in predicting the distortion detection threshold. We then propose a new masking model, where detail loss and additive defects are modeled in two parallel vision channels and interact with each other via a cross masking mechanism. We show that the proposed cross masking model has better adaptability to various image structures and distortions in natural scenes.

  2. New Details of the Human Corneal Limbus Revealed With Second Harmonic Generation Imaging

    PubMed Central

    Park, Choul Yong; Lee, Jimmy K.; Zhang, Cheng; Chuck, Roy S.

    2015-01-01

    Purpose To report novel findings of the human corneal limbus by using second harmonic generation (SHG) imaging. Methods Corneal limbus was imaged by using an inverted two-photon excitation fluorescence microscope. Laser (Ti:Sapphire) was tuned at 850 nm for two-photon excitation. Backscatter signals of SHG and autofluorescence (AF) were collected through a 425/30-nm emission filter and a 525/45-emission filter, respectively. Multiple, consecutive, and overlapping image stacks (z-stack) were acquired for the corneal limbal area. Results Two novel collagen structures were revealed by SHG imaging at the limbus: an anterior limbal cribriform layer and presumed anchoring fibers. Anterior limbal cribriform layer is an intertwined reticular collagen architecture just beneath the limbal epithelial niche and is located between the peripheral cornea and Tenon's/scleral tissue. Autofluorescence imaging revealed high vascularity in this structure. Central to the anterior limbal cribriform layer, radial strands of collagen were found to connect the peripheral cornea to the limbus. These presumed anchoring fibers have both collagen and elastin and were found more extensively in the superficial layers than deep layer and were absent in very deep limbus near Schlemm's canal. Conclusions By using SHG imaging, new details of the collagen architecture of human corneal limbal area were elucidated. High resolution images with volumetric analysis revealed two novel collagen structures. PMID:26393473

  3. On Detailed Contrast of Biomedical Object in X-ray Dark-Field Imaging

    SciTech Connect

    Shimao, Daisuke; Mori, Koichi; Sugiyama, Hiroshi; Kunisada, Toshiyuki; Hyodo, Kazuyuki; Ando, Masami

    2007-01-19

    Over the past 10 years, refraction-based X-ray imaging has been studied together with a perspective view to clinical application. X-ray Dark-Field Imaging that utilizes a Laue geometry analyzer has recently been proposed and has the proven ability to depict articular cartilage in an intact human finger. In the current study, we researched detailed image contrast using X-ray Dark-Field Imaging by observing the edge contrast of an acrylic rod as a simple case, and found differences in image contrast between the right and left edges of the rod. This effect could cause undesirable contrast in the thin articular cartilage on the head of the phalanx. To avoid overlapping with this contrast at the articular cartilage, which would lead to a wrong diagnosis, we suggest that a joint surface on which articular cartilage is located should be aligned in the same sense as the scattering vector of the Laue case analyzer crystal. Defects of articular cartilage were successfully detected under this condition. When utilized under appropriate imaging conditions, X-ray Dark-Field Imaging will be a powerful tool for the diagnosis of arthropathy, as minute changes in articular cartilage may be early-stage features of this disease.

  4. MIDA: A Multimodal Imaging-Based Detailed Anatomical Model of the Human Head and Neck

    PubMed Central

    Iacono, Maria Ida; Neufeld, Esra; Akinnagbe, Esther; Bower, Kelsey; Wolf, Johanna; Vogiatzis Oikonomidis, Ioannis; Sharma, Deepika; Lloyd, Bryn; Wilm, Bertram J.; Wyss, Michael; Pruessmann, Klaas P.; Jakab, Andras; Makris, Nikos; Cohen, Ethan D.; Kuster, Niels; Kainz, Wolfgang; Angelone, Leonardo M.

    2015-01-01

    Computational modeling and simulations are increasingly being used to complement experimental testing for analysis of safety and efficacy of medical devices. Multiple voxel- and surface-based whole- and partial-body models have been proposed in the literature, typically with spatial resolution in the range of 1–2 mm and with 10–50 different tissue types resolved. We have developed a multimodal imaging-based detailed anatomical model of the human head and neck, named “MIDA”. The model was obtained by integrating three different magnetic resonance imaging (MRI) modalities, the parameters of which were tailored to enhance the signals of specific tissues: i) structural T1- and T2-weighted MRIs; a specific heavily T2-weighted MRI slab with high nerve contrast optimized to enhance the structures of the ear and eye; ii) magnetic resonance angiography (MRA) data to image the vasculature, and iii) diffusion tensor imaging (DTI) to obtain information on anisotropy and fiber orientation. The unique multimodal high-resolution approach allowed resolving 153 structures, including several distinct muscles, bones and skull layers, arteries and veins, nerves, as well as salivary glands. The model offers also a detailed characterization of eyes, ears, and deep brain structures. A special automatic atlas-based segmentation procedure was adopted to include a detailed map of the nuclei of the thalamus and midbrain into the head model. The suitability of the model to simulations involving different numerical methods, discretization approaches, as well as DTI-based tensorial electrical conductivity, was examined in a case-study, in which the electric field was generated by transcranial alternating current stimulation. The voxel- and the surface-based versions of the models are freely available to the scientific community. PMID:25901747

  5. The extreme UV imager of solar orbiter: from detailed design to flight model

    NASA Astrophysics Data System (ADS)

    Halain, J.-P.; Rochus, P.; Renotte, E.; Auchère, F.; Berghmans, D.; Harra, L.; Schühle, U.; Schmutz, W.; Zhukov, A.; Aznar Cuadrado, R.; Delmotte, F.; Dumesnil, C.; Gyo, M.; Kennedy, T.; Mercier, R.; Verbeeck, F.; Thome, M.; Heerlein, K.; Hermans, A.; Jacques, L.; Mazzoli, A.; Meining, S.; Rossi, L.; Tandy, J.; Smith, P.; Winter, B.

    2014-07-01

    The Extreme Ultraviolet Imager (EUI) on-board the Solar Orbiter mission will provide full-sun and high-resolution image sequences of the solar atmosphere at selected spectral emission lines in the extreme and vacuum ultraviolet. After the breadboarding and prototyping activities that focused on key technologies, the EUI project has completed the design phase and has started the final manufacturing of the instrument and its validation. The EUI instrument has successfully passed its Critical Design Review (CDR). The process validated the detailed design of the Optical Bench unit and of its sub-units (entrance baffles, doors, mirrors, camera, and filter wheel mechanisms), and of the Electronic Box unit. In the same timeframe, the Structural and Thermal Model (STM) test campaign of the two units have been achieved, and allowed to correlate the associated mathematical models. The lessons learned from STM and the detailed design served as input to release the manufacturing of the Qualification Model (QM) and of the Flight Model (FM). The QM will serve to qualify the instrument units and sub-units, in advance of the FM acceptance tests and final on-ground calibration.

  6. Noise removal and real-time detail enhancement of high-dynamic-range infrared images with time consistency

    NASA Astrophysics Data System (ADS)

    Garcia, Frederic; Schockaert, Cedric; Mirbach, Bruno

    2015-04-01

    This paper presents a noise removal and image detail enhancement method that accounts for the limitations on human's perception to effectively visualize high-dynamic-range (HDR) infrared (IR) images. In order to represent real world scenes, IR images use to be represented by a HDR that generally exceeds the working range of common display devices (8 bits). Therefore, an effective HDR mapping without losing the perceptibility of details is needed. To do so, we introduce the use of two guided filters (GF) to generate an accurate base and detail image component. A plausibility mask is also generated from the combination of the linear coefficients that result from each GF; an indicator of the spatial detail that enables to identify those regions that are prominent to present noise in the detail image component. Finally, we filter the working range of the HDR along time to avoid global brightness fluctuations in the final 8 bit data representation, which results from combining both detail and base image components using a local adaptive gamma correction (LAGC). The last has been designed according to the human vision characteristics. The experimental evaluation shows that the proposed approach significantly enhances image details in addition to improving the contrast of the entire image. Finally, the high performance of the proposed approach makes it suitable for real word applications.

  7. Processing of Uav Based Range Imaging Data to Generate Detailed Elevation Models of Complex Natural Structures

    NASA Astrophysics Data System (ADS)

    Kohoutek, T. K.; Eisenbeiss, H.

    2012-07-01

    Unmanned Aerial Vehicles (UAVs) are more and more used in civil areas like geomatics. Autonomous navigated platforms have a great flexibility in flying and manoeuvring in complex environments to collect remote sensing data. In contrast to standard technologies such as aerial manned platforms (airplanes and helicopters) UAVs are able to fly closer to the object and in small-scale areas of high-risk situations such as landslides, volcano and earthquake areas and floodplains. Thus, UAVs are sometimes the only practical alternative in areas where access is difficult and where no manned aircraft is available or even no flight permission is given. Furthermore, compared to terrestrial platforms, UAVs are not limited to specific view directions and could overcome occlusions from trees, houses and terrain structures. Equipped with image sensors and/or laser scanners they are able to provide elevation models, rectified images, textured 3D-models and maps. In this paper we will describe a UAV platform, which can carry a range imaging (RIM) camera including power supply and data storage for the detailed mapping and monitoring of complex structures, such as alpine riverbed areas. The UAV platform NEO from Swiss UAV was equipped with the RIM camera CamCube 2.0 by PMD Technologies GmbH to capture the surface structures. Its navigation system includes an autopilot. To validate the UAV-trajectory a 360° prism was installed and tracked by a total station. Within the paper a workflow for the processing of UAV-RIM data is proposed, which is based on the processing of differential GNSS data in combination with the acquired range images. Subsequently, the obtained results for the trajectory are compared and verified with a track of a UAV (Falcon 8, Ascending Technologies) carried out with a total station simultaneously to the GNSS data acquisition. The results showed that the UAV's position using differential GNSS could be determined in the centimetre to the decimetre level. The RIM

  8. Detailed imaging of flowing structures at depth using microseismicity: a tool for site investigation?

    NASA Astrophysics Data System (ADS)

    Pytharouli, S.; Lunn, R. J.; Shipton, Z. K.

    2011-12-01

    Field evidence shows that faults and fractures can act as focused pathways or barriers for fluid migration. This is an important property for modern engineering problems, e.g., CO2 sequestration, geological radioactive waste disposal, geothermal energy exploitation, land reclamation and remediation. For such applications the detailed characterization of the location, orientation and hydraulic properties of existing fractures is necessary. These investigations are expensive, requiring the hire of expensive equipment (excavator or drill rigs), which incur standing charges when not in use. In addition, they only provide information for discrete sample 'windows'. Non-intrusive methods have the ability to gather information across an entire area. Methods including electrical resistivity/conductivity and ground penetrating radar (GRP), have been used as tools for site investigations. Their imaging ability is often restricted due to unfavourable on-site conditions e.g. GRP is not useful in cases where a layer of clay or reinforced concrete is present. Our research has shown that high quality seismic data can be successfully used in the detailed imaging of sub-surface structures at depth; using induced microseismicity data recorded beneath the Açu reservoir in Brazil we identified orientations and values of average permeability of open shear fractures at depths up to 2.5km. Could microseismicity also provide information on the fracture width in terms of stress drops? First results from numerical simulations showed that higher stress drop values correspond to narrower fractures. These results were consistent with geological field observations. This study highlights the great potential of using microseismicity data as a supplementary tool for site investigation. Individual large-scale shear fractures in large rock volumes cannot currently be identified by any other geophysical dataset. The resolution of the method is restricted by the detection threshold of the local

  9. Multiparameter double hole contrast detail phantom: Ability to detect image displacement due to off position anode stem

    NASA Astrophysics Data System (ADS)

    Pauzi, Nur Farahana; Majid, Zafri Azran Abdul; Sapuan, Abdul Halim; Azemin, Mohd Zulfaezal Che; Junet, Laila Kalidah

    2015-04-01

    Contrast Detail phantom is a quality control tool to analyze the performance of imaging devices. Currently, its function is solely to evaluate the contrast detail characteristic of imaging system. It consists of drilled hole which gives effect to the penetration of x-ray beam divergence to pass through the base of each hole. This effect will lead to false appearance of image from its original location but it does not being visualized in the radiograph. In this study, a new design of Contrast Detail phantom's hole which consists of double hole construction has been developed. It can detect the image displacement which is due to off position of anode stem from its original location. The double hole differs from previous milled hole, whereby it consists of combination of different hole diameters. Small hole diameter (3 mm) is positioned on top of larger hole diameter (10 mm). The thickness of double hole acrylic blocks is 13 mm. Result revealed` that, Multiparameter Double Hole Contrast Detail phantom can visualize the shifted flaw image quality produced by x-ray machine due to improper position of the anode stem which is attached to rotor and stator. The effective focal spot of x-ray beam also has been shifted from the center of collimator as a result of off-position anode stem. As a conclusion, the new design of double hole Contrast Detail phantom able to measure those parameters in a well manner.

  10. Multiparameter double hole contrast detail phantom: Ability to detect image displacement due to off position anode stem

    SciTech Connect

    Pauzi, Nur Farahana; Majid, Zafri Azran Abdul; Sapuan, Abdul Halim; Junet, Laila Kalidah; Azemin, Mohd Zulfaezal Che

    2015-04-24

    Contrast Detail phantom is a quality control tool to analyze the performance of imaging devices. Currently, its function is solely to evaluate the contrast detail characteristic of imaging system. It consists of drilled hole which gives effect to the penetration of x-ray beam divergence to pass through the base of each hole. This effect will lead to false appearance of image from its original location but it does not being visualized in the radiograph. In this study, a new design of Contrast Detail phantom’s hole which consists of double hole construction has been developed. It can detect the image displacement which is due to off position of anode stem from its original location. The double hole differs from previous milled hole, whereby it consists of combination of different hole diameters. Small hole diameter (3 mm) is positioned on top of larger hole diameter (10 mm). The thickness of double hole acrylic blocks is 13 mm. Result revealed that Multiparameter Double Hole Contrast Detail phantom can visualize the shifted flaw image quality produced by x-ray machine due to improper position of the anode stem which is attached to rotor and stator. The effective focal spot of x-ray beam also has been shifted from the center of collimator as a result of off-position anode stem. As a conclusion, the new design of double hole Contrast Detail phantom able to measure those parameters in a well manner.

  11. Assessment of Invasive Breast Cancer Heterogeneity Using Whole-Tumor Magnetic Resonance Imaging Texture Analysis: Correlations With Detailed Pathological Findings.

    PubMed

    Ko, Eun Sook; Kim, Jae-Hun; Lim, Yaeji; Han, Boo-Kyung; Cho, Eun Yoon; Nam, Seok Jin

    2016-01-01

    There is no study that investigates the potential correlation between the heterogeneity obtained from texture analysis of medical images and the heterogeneity observed from histopathological findings. We investigated whether texture analysis of magnetic resonance images correlates with histopathological findings.Seventy-five patients with estrogen receptor positive invasive ductal carcinoma who underwent preoperative breast magnetic resonance imaging (MRI) were included. Tumor entropy and uniformity were determined on T2- and contrast-enhanced T1-weighted subtraction images under different filter levels. Two pathologists evaluated the detailed histopathological findings of the tumors including tumor cellularity, dominant stroma type, central scar, histologic grade, extensive intraductal component (EIC), and lymphovascular invasion. Entropy and uniformity values on both T2- and contrast-enhanced T1-weighted subtraction images were compared with detailed pathological findings.In a multivariate analysis, entropy significantly increased only on unfiltered T2-weighted images (P = 0.013). Tumor cellularity and predominant stroma did not affect the uniformity or entropy on both T2- and contrast-enhanced T1-weighted subtraction images. High histologic grades showed increased uniformity and decreased entropy on contrast-enhanced T1-weighted subtraction images, whereas the opposite tendency was observed on T2-weighted images. Invasive ductal carcinoma with an EIC or lymphovascular invasion only affected the contrast-enhanced T1-weighted subtraction images, through increased uniformity and decreased entropy. The best uniformity results were recorded on T2- and contrast-enhanced T1-weighted subtraction images at a filter level of 0.5. Entropy showed the best results at a filter level of 0.5 on contrast-enhanced T1-weighted subtraction images. However, on T2-weighted images, an ideal model was achieved on unfiltered images.MRI texture analysis correlated with pathological

  12. The level of detail required in a deformable phantom to accurately perform quality assurance of deformable image registration

    NASA Astrophysics Data System (ADS)

    Saenz, Daniel L.; Kim, Hojin; Chen, Josephine; Stathakis, Sotirios; Kirby, Neil

    2016-09-01

    The primary purpose of the study was to determine how detailed deformable image registration (DIR) phantoms need to adequately simulate human anatomy and accurately assess the quality of DIR algorithms. In particular, how many distinct tissues are required in a phantom to simulate complex human anatomy? Pelvis and head-and-neck patient CT images were used for this study as virtual phantoms. Two data sets from each site were analyzed. The virtual phantoms were warped to create two pairs consisting of undeformed and deformed images. Otsu’s method was employed to create additional segmented image pairs of n distinct soft tissue CT number ranges (fat, muscle, etc). A realistic noise image was added to each image. Deformations were applied in MIM Software (MIM) and Velocity deformable multi-pass (DMP) and compared with the known warping. Images with more simulated tissue levels exhibit more contrast, enabling more accurate results. Deformation error (magnitude of the vector difference between known and predicted deformation) was used as a metric to evaluate how many CT number gray levels are needed for a phantom to serve as a realistic patient proxy. Stabilization of the mean deformation error was reached by three soft tissue levels for Velocity DMP and MIM, though MIM exhibited a persisting difference in accuracy between the discrete images and the unprocessed image pair. A minimum detail of three levels allows a realistic patient proxy for use with Velocity and MIM deformation algorithms.

  13. The level of detail required in a deformable phantom to accurately perform quality assurance of deformable image registration.

    PubMed

    Saenz, Daniel L; Kim, Hojin; Chen, Josephine; Stathakis, Sotirios; Kirby, Neil

    2016-09-01

    The primary purpose of the study was to determine how detailed deformable image registration (DIR) phantoms need to adequately simulate human anatomy and accurately assess the quality of DIR algorithms. In particular, how many distinct tissues are required in a phantom to simulate complex human anatomy? Pelvis and head-and-neck patient CT images were used for this study as virtual phantoms. Two data sets from each site were analyzed. The virtual phantoms were warped to create two pairs consisting of undeformed and deformed images. Otsu's method was employed to create additional segmented image pairs of n distinct soft tissue CT number ranges (fat, muscle, etc). A realistic noise image was added to each image. Deformations were applied in MIM Software (MIM) and Velocity deformable multi-pass (DMP) and compared with the known warping. Images with more simulated tissue levels exhibit more contrast, enabling more accurate results. Deformation error (magnitude of the vector difference between known and predicted deformation) was used as a metric to evaluate how many CT number gray levels are needed for a phantom to serve as a realistic patient proxy. Stabilization of the mean deformation error was reached by three soft tissue levels for Velocity DMP and MIM, though MIM exhibited a persisting difference in accuracy between the discrete images and the unprocessed image pair. A minimum detail of three levels allows a realistic patient proxy for use with Velocity and MIM deformation algorithms. PMID:27494827

  14. Enceladus Close Up: New Details Recovered from Cassini ISS Boresight-Drag Images

    NASA Astrophysics Data System (ADS)

    Helfenstein, Paul; Thomas, P. C.; Veverka, J.

    2013-10-01

    Among the many Cassini ISS (Imaging Science Subsystem) images of Enceladus are a few severely-underexposed, motion-blurred images that were acquired on “boresight-drag” events on the closest flybys. During boresight-drags, ISS is statically aimed at a point that intercepts the predicted path of Enceladus’ across the sky. The ISS Narrow angle (NAC) and Wide Angle (WAC) cameras are repeatedly triggered together in hope of serendipitously capturing a close-up “BOTSIM” image-pair of the body as it passes. Because the events are so fast, the surface footprints and lighting geometry cannot be predicted in advance - a cascade of images are just quickly shuttered at the minimum 5 msec exposure. On each of four boresight-drags, surface images were captured. However, the two most recent (image-pair W/N1669812043 in November 2010 and W/N1713106405 in April 2012, respectively) were poorly illuminated -- three of four images only in Saturnshine. Despite their poor signal quality, they are rare images of Enceladus’ surface obtained with spatial resolutions better than a few meters/pixel. Careful use of Fourier filtering and spatial reconstruction techniques was needed to eliminate image noise and residual electronic banding that was not removed during routine radiometric calibration of the images. Fourier motion debluring techniques were then applied to correct for significant motion smear. Images W/N1669812043 (55.1°N, 20.2°W) are in old cratered terrain, inside a prominent 23 km sized impact crater along the rise of its updomed floor. They show a system of parallel ~250m wide mesas trending around the dome’s circumference. Smooth detritus inundates mesas and valleys near the dome summit and the mesa surfaces are otherwise mantled with regolith that is finely cratered down to the ~2 m/pixel NAC resolution limit. W/N1713106405 (66.9°S, 29.5°W) show the chaotically fractured margin of the active South Polar Terrain - an area divided by parallel ridges and

  15. Integration of Point Clouds Originated from Laser Scaner and Photogrammetric Images for Visualization of Complex Details of Historical Buildings

    NASA Astrophysics Data System (ADS)

    Altuntas, C.

    2015-02-01

    Three-dimensional (3D) models of historical buildings are created for documentation and virtual realization of them. Laser scanning and photogrammetry are extensively used to perform for these aims. The selection of the method that will be used in threedimensional modelling study depends on the scale and shape of the object, and also applicability of the method. Laser scanners are high cost instruments. However, the cameras are low cost instruments. The off-the-shelf cameras are used for taking the photogrammetric images. The camera is imaging the object details by carrying on hand while the laser scanner makes ground based measurement. Laser scanner collect high density spatial data in a short time from the measurement area. On the other hand, image based 3D (IB3D) measurement uses images to create 3D point cloud data. The image matching and the creation of the point cloud can be done automatically. Historical buildings include more complex details. Thus, all details cannot be measured by terrestrial laser scanner (TLS) due to the blocking the details with each others. Especially, the artefacts which have complex shapes cannot be measured in full details. They cause occlusion on the point cloud model. However it is possible to record photogrammetric images and creation IB3D point cloud for these areas. Thus the occlusion free 3D model is created by the integration of point clouds originated from the TLS and photogrammetric images. In this study, usability of laser scanning in conjunction with image based modelling for creation occlusion free three-dimensional point cloud model of historical building was evaluated. The IB3D point cloud was created in the areas that could not been measured by TLS. Then laser scanning and IB3D point clouds were integrated in the common coordinate system. The registration point clouds were performed with the iterative closest point (ICP) and georeferencing methods. Accuracy of the registration was evaluated by convergency and its

  16. Large-scale aerial images capture details of invasive plant populations

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Satellite and aerial remote sensing have been successfully used to measure invasive weed infestations over very large areas, but have limited resolution. Ground-based methods have provided detailed measurements of invasive weeds, but can measure only limited areas. Here we test a novel approach th...

  17. FAST TRACK COMMUNICATION Far-field x-ray phase contrast imaging has no detailed information on the object

    NASA Astrophysics Data System (ADS)

    Kohn, V. G.; Argunova, T. S.; Je, J. H.

    2010-11-01

    We show that x-ray phase contrast images of some objects with a small cross-section diameter d satisfy a condition for a far-field approximation d Lt r1 where r1 = (λz)1/2, λ is the x-ray wavelength, z is the distance from the object to the detector. In this case the size of the image does not match the size of the object contrary to the edge detection technique. Moreover, the structure of the central fringes of the image is universal, i.e. it is independent of the object cross-section structure. Therefore, these images have no detailed information on the object.

  18. Contextual consistency facilitates long-term memory of perceptual detail in barely seen images.

    PubMed

    Gronau, Nurit; Shachar, Meytal

    2015-08-01

    It is long known that contextual information affects memory for an object's identity (e.g., its basic level category), yet it is unclear whether schematic knowledge additionally enhances memory for the precise visual appearance of an item. Here we investigated memory for visual detail of merely glimpsed objects. Participants viewed pairs of contextually related and unrelated stimuli, presented for an extremely brief duration (24 ms, masked). They then performed a forced-choice memory-recognition test for the precise perceptual appearance of 1 of 2 objects within each pair (i.e., the "memory-target" item). In 3 experiments, we show that memory-target stimuli originally appearing within contextually related pairs are remembered better than targets appearing within unrelated pairs. These effects are obtained whether the target is presented at test with its counterpart pair object (i.e., when reiterating the original context at encoding) or whether the target is presented alone, implying that the contextual consistency effects are mediated predominantly by processes occurring during stimulus encoding, rather than during stimulus retrieval. Furthermore, visual detail encoding is improved whether object relations involve implied action or not, suggesting that, contrary to some prior suggestions, action is not a necessary component for object-to-object associative "grouping" processes. Our findings suggest that during a brief glimpse, but not under long viewing conditions, contextual associations may play a critical role in reducing stimulus competition for attention selection and in facilitating rapid encoding of sensory details. Theoretical implications with respect to classic frame theories are discussed. (PsycINFO Database Record PMID:26010591

  19. A method for detailed analysis of the structure of mast cell secretory granules by negative contrast imaging

    PubMed Central

    Tanaka, Shotaro; Takakuwa, Yuichi

    2016-01-01

    Secretory granules (SGs) in mast cells contain various molecules that elicit allergy symptoms and are generally considered therapeutic targets. However, the biogenesis, maintenance, regulation, and recycling of these granules remain controversial, mainly due to the lack of suitable live-cell imaging methods. In this study, we applied negative contrast imaging with soluble green fluorescent protein (GFP) expressed in the cytoplasm as a method to validate structural information of mast cell SGs. We evaluated the accuracy of the method in detail, and we demonstrated that it can be used for quantitative analysis. Using this technique, secretory granules, the nucleus, mitochondria, and the cell body were visualized in individual RBL-2H3 mast cells without any influence. When combined with conventional multicolor fluorescence imaging, visualization of SG-associated proteins and SG–SG fusion was achieved. Moreover, 3D images were constructed based on this method, and detailed information on the number, size, and shape of individual SGs was obtained. We found that cell volume was correlated with SG number. In summary, the technique provides valuable and unique data, and will therefore advance SG research. PMID:26997316

  20. Detailed study of scratch drive actuator characteristics using high-speed imaging

    NASA Astrophysics Data System (ADS)

    Li, Lijie; Brown, James G.; Uttamchandani, Deepak G.

    2001-10-01

    Microactuators are one of the key components in MEMS and Microsystems technology, and various designs have been realized through different fabrication processes. One type of microactuator commonly used is the scratch drive actuator (SDA) that is frequently fabricated by surface micromachining processes. An experimental investigation has been conducted on the characteristics of SDAs fabricated using the Cronos Microsystems MUMPs process. The motivation is to compare the response of SDAs located on the same die, and SDAs located on the different dies from the same fabrication batch. A high-speed imaging camera has been used to precisely determine important SDA characteristics such as step size, velocity, maximum velocity, and acceleration over long travel distance. These measurements are important from a repeatability point of view, and in order to fully exploit the potential of the SDA as a precise positioning mechanism. 2- and 3-stage SDAs have been designed and fabricated for these experiments. Typical step sizes varying from 7 nm at a driving voltage of 60 V to 23 nm at 290 V have been obtained.

  1. Detailed Tremor Migration Styles in Guerrero, Mexico Imaged with Cross-station Cross-correlations

    NASA Astrophysics Data System (ADS)

    Peng, Y.; Rubin, A. M.

    2015-12-01

    Tremor occurred downdip of the area that slipped the most during the 2006 slow slip event (SSE) in Guerrero, Mexico, as opposed to Cascadia, where tremor locations and rupture zones of SSEs largely overlap. Here we obtain high resolution tremor locations by applying cross-station cross-correlations [Armbruster et al., 2014] to seismic data from the Meso-America Subduction Experiment deployment. A few 3-station detectors are adopted to capture detailed deformation styles in the tremor "transient zone" and the downdip "sweet spot" as defined in Frank et al., 2014. Similar to Cascadia, tremor activities in our study region were comprised mostly of short tremor bursts lasting minutes to hours. Many of these bursts show clear migration patterns with propagation velocities of hundreds of km/day, comparable to those in Cascadia. However, the propagation of the main tremor front was often not in a simple unilateral fashion. Before the 2006 SSE, we observe 4 large tremor episodes during which both the transient zone and the sweet spot participated, consistent with previous findings [Frank et al., 2014]. The transient zone usually became active a few days after the sweet spot. We find many along-dip migrations with recurrence intervals of about a half day within a region about 10 km along strike and 35 km along dip in the sweet spot, suggesting possible tidal modulation, after the main front moved beyond this region. These migrations appear not to originate at the main front, in contrast to tremor migrations from a few km to tens of km across observed in Cascadia [Rubin and Armbruster, 2013; Peng et al., 2015; Peng and Rubin, submitted], but possibly similar to Shikoku, Japan [Shelly et al., 2007]. We do not observe obvious half-day periodicity for the migrations farther downdip within the sweet spot. During the SSE, the recurrence interval of tremor episodes decreased significantly in both the transient zone and the sweet spot, with that of the former being much shorter

  2. Quantitative assessment of hyperspectral imaging in detection of plasmonic nanoparticles: a modified contrast-detail analysis approach

    NASA Astrophysics Data System (ADS)

    Wang, Jianting; Chen, Yu; Pfefer, T. Joshua

    2016-03-01

    Hyperspectral reflectance imaging (HRI) is an emerging imaging modality being applied for clinical indications such as tissue oximetry, and cancer detection based on endogenous biological constituents including plasmonic nanoparticles. However, there is currently a lack of standardized test methods for objective, quantitative evaluation of HRI system performance. Contrast-detail analysis (CDA) is a phantom-based test method commonly used to evaluate medical imaging devices (e.g., mammography systems) in terms of their lower detection limit. We investigated a modified CDA (mCDA) method to quantify the detectability of gold nanoparticles by HRI systems. Silicone-based turbid phantoms containing micro-fluidic channels were developed for the mCDA tests. Polydimethylsiloxane (PDMS) phantom materials were doped with chromophores and scatterers to achieve biologically relevant optical properties (OPs). Molds were used to produce cylindrical channels of diameters 0.3 to 1.65 mm and depths of 0.2 mm inside the phantoms. Channels were filled with a mixture of hemoglobin and concentrations of gold nanorods (GNR) and measured with our HRI system. The contrast of GNRs was solved with a spectral unmixing algorithm from the reflectance spectra. The lowest detectable concentration was determined as a function of inclusion size and depth and plotted as modified contrast detail curve (mCDC). mCDCs were used to compare the detectabilities of the HRI system with different data processing algorithms. It is demonstrated that our mCDA test method involving turbid microchannel phantoms can help to elucidate the combined performance of imaging devices and plasmonic nanoparticle contrast agents. This approach may be useful for performing clinical trial standardization and device re-calibration, thus ensuring quality control and clinical performance.

  3. Recent improvements and developments in uncooled systems at BAE SYSTEMS North America

    NASA Astrophysics Data System (ADS)

    Backer, Brian S.; Butler, Neal R.; Kohin, Margaret; Gurnee, Mark N.; Whitwam, Jason T.; Breen, Tom

    2002-08-01

    BAE SYSTEMS has designed and developed MicroIR microbolometer focal plane arrays (FPAs) in three formats (160x120, 320x240, and 640x480) and with two different pixel sizes (46micrometers and 28micrometers ). In addition to successfully demonstrating these FPA technologies, BAE SYSTEMS has produced and delivered thousands of 320x240 (46micrometers pixel) imaging modules and camera cores for military, thermography, firefighting, security and numerous other applications throughout the world. Recently, BAE SYSTEMS has started production deliveries of 160x120 (46micrometers ) systems, demonstrated 320x240 and 640x480 second-generation (28micrometers ) imaging, and demonstrated second-generation thermoelectric cooler-less operation. This paper discusses these recent accomplishments and, when possible, provides quantitative NETD and performance data for our newly developed FPAs and systems. Video will be shown to demonstrate sensor performance capabilities.

  4. Advances in uncooled systems applications

    NASA Astrophysics Data System (ADS)

    Anderson, John S.; Bradley, Daryl; Chen, Chungte W.; Chin, Richard; Gonzalez, H.; Hegg, Ronald G.; Kostrzewa, K.; Le Pere, C.; Ton, S.; Kennedy, Adam; Murphy, Daniel F.; Ray, Michael; Wyles, Richard; Miller, James E.; Newsome, Gwendolyn W.

    2003-09-01

    The Low Cost Microsensors (LCMS) Program recently demonstrated state-of-the-art imagery in a long-range infrared (IR) sensor built upon an uncooled vanadium oxide (VOx) 640 x 480 format focal plane array (FPA) engine. The 640 x 480 sensor is applicable to long-range surveillance and targeting missions. The intent of this DUS&T effort was to further reduce the cost, weight, and power of uncooled IR sensors, and to increase the capability of these sensors, thereby expanding their applicability to military and commercial markets never before addressed by thermal imaging. In addition, the Advanced Uncooled Thermal Imaging Sensors (AUTIS) Program extended this development to light-weight, compact unmanned aerial vehicle (UAV) applications.

  5. Advances in uncooled technology at BAE SYSTEMS

    NASA Astrophysics Data System (ADS)

    Backer, Brian S.; Kohin, Margaret; Leary, Arthur R.; Blackwell, Richard J.; Rumbaugh, Roy N.

    2003-09-01

    BAE SYSTEMS has made tremendous progress in uncooled technology and systems in the last year. In this paper we present performance results and imagery from our latest 640x480 and 320x240 small pixel focal plane arrays. Both were produced using submicron lithography and have achieved our lowest NETDs to date. Testing of the 320x240 devices has shown TNETDs of 30mK at F/1. Video imagery from our 640 x 480 uncooled camera installed in a POINTER Unattended Aerial Vehicle is also shown. In addition, we introduce our newest commercial imaging camera core, the SCC500 and show its vastly improved characteristics. Lastly, plans for future advancements are outlined.

  6. Combining Seismic Arrays to Image Detailed Rupture Properties of Large Earthquakes: Evidence for Frequent Triggering of Multiple Faults

    NASA Astrophysics Data System (ADS)

    Ishii, M.; Kiser, E.

    2010-12-01

    Imaging detailed rupture characteristics using the back-projection method, which time-reverses waveforms to their source, has become feasible in recent years due to the availability of data from large aperture arrays with dense station coverage. In contrast to conventional techniques, this method can quickly and indiscriminately provide the spatio-temporal details of rupture propagation. Though many studies have utilized the back-projection method with a single regional array, the limited azimuthal coverage often leads to skewed resolution. In this study, we enhance the imaging power by combining data from two arrays, i.e., the Transportable Array (TA) in the United States and the High Sensitivity Seismographic Network (Hi-net) in Japan. This approach suppresses artifacts and achieves good lateral resolution by improving distance and azimuthal coverage while maintaining waveform coherence. We investigate four large events using this method: the August 15, 2007 Pisco, Peru earthquake, the September 12, 2007 Southern Sumatra earthquake, the September 29, 2009 Samoa Islands earthquake, and the February 27, 2010 Maule, Chile earthquake. In every case, except the Samoa Islands event, the distance of one of the arrays from the epicenter requires us to use the direct P wave and core phases in the back-projection. One of the common features of the rupture characteristics obtained from the back-projection analysis is spatio-temporal rupture discontinuities, or discrete subevents. Both the size of the gaps and the timing between subevents suggest that multiple segments are involved during giant earthquakes, and that they trigger slip on other faults. For example, the 2009 Samoa Islands event began with a rupture propagating north for about 15 seconds followed by a much larger rupture that originated 30 km northwest of the terminus of the first event and propagated back toward the southeast. The involvement of multiple rupture segments with different slip characteristics

  7. Psychophysical evaluation of the image quality of a dynamic flat-panel digital x-ray image detector using the threshold contrast detail detectability (TCDD) technique

    NASA Astrophysics Data System (ADS)

    Davies, Andrew G.; Cowen, Arnold R.; Bruijns, Tom J. C.

    1999-05-01

    We are currently in an era of active development of the digital X-ray imaging detectors that will serve the radiological communities in the new millennium. The rigorous comparative physical evaluations of such devices are therefore becoming increasingly important from both the technical and clinical perspectives. The authors have been actively involved in the evaluation of a clinical demonstration version of a flat-panel dynamic digital X-ray image detector (or FDXD). Results of objective physical evaluation of this device have been presented elsewhere at this conference. The imaging performance of FDXD under radiographic exposure conditions have been previously reported, and in this paper a psychophysical evaluation of the FDXD detector operating under continuous fluoroscopic conditions is presented. The evaluation technique employed was the threshold contrast detail detectability (TCDD) technique, which enables image quality to be measured on devices operating in the clinical environment. This approach addresses image quality in the context of both the image acquisition and display processes, and uses human observers to measure performance. The Leeds test objects TO[10] and TO[10+] were used to obtain comparative measurements of performance on the FDXD and two digital spot fluorography (DSF) systems, one utilizing a Plumbicon camera and the other a state of the art CCD camera. Measurements were taken at a range of detector entrance exposure rates, namely 6, 12, 25 and 50 (mu) R/s. In order to facilitate comparisons between the systems, all fluoroscopic image processing such as noise reduction algorithms, were disabled during the experiments. At the highest dose rate FDXD significantly outperformed the DSF comparison systems in the TCDD comparisons. At 25 and 12 (mu) R/s all three-systems performed in an equivalent manner and at the lowest exposure rate FDXD was inferior to the two DSF systems. At standard fluoroscopic exposures, FDXD performed in an equivalent

  8. Prehospital digital photography and automated image transmission in an emergency medical service – an ancillary retrospective analysis of a prospective controlled trial

    PubMed Central

    2013-01-01

    Background Still picture transmission was performed using a telemedicine system in an Emergency Medical Service (EMS) during a prospective, controlled trial. In this ancillary, retrospective study the quality and content of the transmitted pictures and the possible influences of this application on prehospital time requirements were investigated. Methods A digital camera was used with a telemedicine system enabling encrypted audio and data transmission between an ambulance and a remotely located physician. By default, images were compressed (jpeg, 640 x 480 pixels). On occasion, this compression was deactivated (3648 x 2736 pixels). Two independent investigators assessed all transmitted pictures according to predefined criteria. In cases of different ratings, a third investigator had final decision competence. Patient characteristics and time intervals were extracted from the EMS protocol sheets and dispatch centre reports. Results Overall 314 pictures (mean 2.77 ± 2.42 pictures/mission) were transmitted during 113 missions (group 1). Pictures were not taken for 151 missions (group 2). Regarding picture quality, the content of 240 (76.4%) pictures was clearly identifiable; 45 (14.3%) pictures were considered “limited quality” and 29 (9.2%) pictures were deemed “not useful” due to not/hardly identifiable content. For pictures with file compression (n = 84 missions) and without (n = 17 missions), the content was clearly identifiable in 74% and 97% of the pictures, respectively (p = 0.003). Medical reports (n = 98, 32.8%), medication lists (n = 49, 16.4%) and 12-lead ECGs (n = 28, 9.4%) were most frequently photographed. The patient characteristics of group 1 vs. 2 were as follows: median age – 72.5 vs. 56.5 years, p = 0.001; frequency of acute coronary syndrome – 24/113 vs. 15/151, p = 0.014. The NACA scores and gender distribution were comparable. Median on-scene times were longer with picture transmission (26 vs. 22

  9. Detailed Decomposition of Galaxy Images II: Fitting Spiral Arms, Bars, and Non-axisymmetric Structures in GALFIT 3.0

    NASA Astrophysics Data System (ADS)

    Peng, Chien Y.; Ho, L. C.; Impey, C. D.; Rix, H. W.

    2007-12-01

    The technique of fitting galaxy light profiles with analytic functions (e.g. de Vaucouleurs, exponential), also known as parametric fitting, has been a useful tool for studying galaxy structure and evolution. It is often used to quantify global properties of galaxies such as luminosity, size, ellipticity, and profile shape in a self-consistent manner. It also allows one to deblend multiple components of a galaxy, e.g. bulge/disk/bar/AGN, or to separate overlapping galaxies in a rigorous and robust way. However, the traditional method of fitting galaxies relies on using ellipsoid models, which is sometimes criticized to argue in favor of non-parametric techniques. In this study, we show that two dimensional image fitting is not fundamentally restricted to using axisymmetric ellipsoid shapes. By breaking from axisymmetry parametrically through the use of Fourier modes, one can better quantify the degree of galaxy irregularity in an intuitive and well-motivated manner. We also introduce a technique that allows one to fit spiral structures in late-type galaxies through the use of coordinate rotation. By comparing with more realistic models now possible, we find that the traditional use of simple ellipsoid models is robust even on irregular and spiral galaxies, because single component fits are by nature large scale averages. However, when it comes to quantifying sub-components of a galaxy, sometimes it is necessary to model structures in detail, such as when performing bulge-to-disk decomposition of galaxies with strong spiral arms, or quantifying the symmetry due to bright (e.g. bulge) and faint (e.g. disk) galaxy sub-components separately. These new techniques are implemented in GALFIT 3.0 (http://www.ociw.edu/ peng/work/galfit/galfit.html ). CYP gratefully acknowledges support from the Plaskett Fellowship (NRC-HIA) and the Institute/Giacconi Fellowship (STScI) programs.

  10. Real-time visualization of low contrast targets from high-dynamic range infrared images based on temporal digital detail enhancement filter

    NASA Astrophysics Data System (ADS)

    Garcia, Frederic; Schockaert, Cedric; Mirbach, Bruno

    2015-11-01

    An image detail enhancement method to effectively visualize low contrast targets in high-dynamic range (HDR) infrared (IR) images is presented regardless of the dynamic range width. In general, high temperature dynamics from real-world scenes used to be encoded in a 12 or 14 bits IR image. However, the limitations of the human visual perception, from which no more than 128 shades of gray are distinguishable, and the 8-bit working range of common display devices make necessary an effective 12/14 bits HDR mapping into the 8-bit data representation. To do so, we propose to independently treat the base and detail image components that result from splitting the IR image using two dedicated guided filters. We also introduce a plausibility mask from which those regions that are prominent to present noise are accurately defined to be explicitly tackled to avoid noise amplification. The final 8-bit data representation results from the combination of the processed detail and base image components and its mapping to the 8-bit domain using an adaptive histogram-based projection approach. The limits of the histogram are accommodated through time in order to avoid global brightness fluctuations between frames. The experimental evaluation shows that the proposed noise-aware approach preserves low contrast details with an overall contrast enhancement of the image. A comparison with widely used HDR mapping approaches and runtime analysis is also provided. Furthermore, the proposed mathematical formulation enables a real-time adjustment of the global contrast and brightness, letting the operator adapt to the visualization display device without nondesirable artifacts.

  11. Functional hyperspectral imaging captures subtle details of cell metabolism in olfactory neurosphere cells, disease-specific models of neurodegenerative disorders.

    PubMed

    Gosnell, Martin E; Anwer, Ayad G; Cassano, Juan C; Sue, Carolyn M; Goldys, Ewa M

    2016-01-01

    Hyperspectral imaging uses spectral and spatial image information for target detection and classification. In this work hyperspectral autofluorescence imaging was applied to patient olfactory neurosphere-derived cells, a cell model of a human metabolic disease MELAS (mitochondrial myopathy, encephalomyopathy, lactic acidosis, stroke-like syndrome). By using an endogenous source of contrast subtle metabolic variations have been detected between living cells in their full morphological context which made it possible to distinguish healthy from diseased cells before and after therapy. Cellular maps of native fluorophores, flavins, bound and free NADH and retinoids unveiled subtle metabolic signatures and helped uncover significant cell subpopulations, in particular a subpopulation with compromised mitochondrial function. Taken together, our results demonstrate that multispectral spectral imaging provides a new non-invasive method to investigate neurodegenerative and other disease models, and it paves the way for novel cellular characterisation in health, disease and during treatment, with proper account of intrinsic cellular heterogeneity. PMID:26431992

  12. Devilish Details

    NASA Technical Reports Server (NTRS)

    2005-01-01

    23 September 2005 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows a small, springtime dust devil creating a dark streak on the plains of Argyre. The small, bright dot is the dust devil. Many other dark streaks on the plains indicate the areas where other dust devils had passed within the past several weeks before this July 2005 image was acquired.

    Location near: 44.6oS, 40.3oW Image width: width: 3 km (1.9 mi) Illumination from: upper left Season: Southern Spring

  13. Details of Glaucomatous Damage Are Better Seen on OCT En Face Images Than on OCT Retinal Nerve Fiber Layer Thickness Maps

    PubMed Central

    Hood, Donald C.; Fortune, Brad; Mavrommatis, Maria A.; Reynaud, Juan; Ramachandran, Rithambara; Ritch, Robert; Rosen, Richard B.; Muhammad, Hassan; Dubra, Alfredo; Chui, Toco Y. P.

    2015-01-01

    Purpose High-resolution images of glaucomatous damage to the retinal nerve fiber layer (RNFL) were obtained with an adaptive optics-scanning light ophthalmoscope (AO-SLO) and used as a basis for comparisons between en face slab images and thickness maps derived from optical coherence tomography (OCT) scans. Methods Wide-field (9 × 12 mm) cube scans were obtained with swept-source OCT (DRI-OCT) from six eyes of six patients. All eyes had a deep defect near fixation as seen on a 10-2 visual field test. Optical coherence tomography en face images, based on the average reflectance intensity, were generated (ATL 3D-Suite) from 52-μm slabs just below the vitreal border of the inner limiting membrane. The RNFL thickness maps were generated from the same OCT data. Both were compared with the AO-SLO peripapillary images that were previously obtained. Results On AO-SLO images, three eyes showed small regions of preserved and/or missing RNFL bundles within the affected region. Details in these regions were seen on the OCT en face images but not on the RNFL thickness maps. In addition, in the healthier hemi-retinas of two eyes, there were darker, arcuate-shaped regions on en face images that corresponded to abnormalities seen on AO-SLO. These were not seen on RNFL thickness maps. Conclusions Details of local glaucomatous damage, missing or easily overlooked on traditional OCT RNFL thickness analysis used in clinical OCT reports, were seen on OCT en face images based on the average reflectance intensity. While more work is needed, it is likely that en face slab imaging has a role in the clinical management of glaucoma. PMID:26426403

  14. High-resolution single-molecule recognition imaging of the molecular details of ricin-aptamer interaction

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The molecular details of DNA aptamer-ricin interactions were investigated. The toxic protein ricin molecules were immobilized on Au(111) surface using N-hydroxysuccinimide (NHS) ester to specifically react with lysine residues located on the ricin B chains. A single ricin molecule was visualized in ...

  15. Dynamism & Detail

    ERIC Educational Resources Information Center

    Flannery, Maura C.

    2004-01-01

    New material discovered in the study of cell research is presented for the benefit of biology teachers. Huge amounts of data are being generated in fields like cellular dynamics, and it is felt that people's understanding of the cell is becoming much more complex and detailed.

  16. Resolving the surface details on Venus in the balloon- or lander-borne images with a computer modeling method

    NASA Astrophysics Data System (ADS)

    Ekonomov, A. P.

    2015-04-01

    Due to the presence of opaque clouds at high altitudes, it is difficult to survey the surface of Venus in the optical spectral range. At the same time, in the under-cloud layer, there are transparency windows at the wavelengths λ = 1.08, 0.85, and 0.65 μm. At these wavelengths, the gaseous absorption (in the whole atmosphere rather than only in the under-cloud layer) is weaker, and the atmospheric transparency is mainly determined by the scattering on molecules. The paper presents the results of the Monte-Carlo computer modeling of the imaging of the surface from a balloon or a lander. It has been shown that the imaging from the lower boundary of the clouds is possible.

  17. Use of MODIS satellite images for detailed lake morphometry: Application to basins with large water level fluctuations

    NASA Astrophysics Data System (ADS)

    Ovakoglou, George; Alexandridis, Thomas K.; Crisman, Thomas L.; Skoulikaris, Charalampos; Vergos, George S.

    2016-09-01

    Lake morphometry is essential for managing water resources and limnetic ecosystems. For reservoirs that receive high sediment loads, frequent morphometric mapping is necessary to define both the effective life of the reservoir and its water storage capacity for irrigation, power generation, flood control and domestic water supply. The current study presents a methodology for updating the digital depth model (DDM) of lakes and reservoirs with wide intra and interannual fluctuations of water levels using satellite remote sensing. A time series of Terra MODIS satellite images was used to map shorelines formed during the annual water level change cycle, and were validated with concurrent Landsat ETM+ satellite images. The shorelines were connected with in-situ observation of water levels and were treated as elevation contours to produce the DDM using spatial interpolation. The accuracy of the digitized shorelines is within the mapping accuracy of the satellite images, while the resulting DDM is validated using in-situ elevation measurements. Two versions of the DDM were produced to assess the influence of seasonal water fluctuation. Finally, the methodology was applied to Lake Kerkini (Greece) to produce an updated DDM, which was compared with the last available bathymetric survey (1991) and revealed changes in sediment distribution within the lake.

  18. Evaluation of lunar rocks and soils for resource utilization: Detailed image analysis of raw materials and beneficiated products

    NASA Technical Reports Server (NTRS)

    Taylor, Lawrence A.; Chambers, John G.; Patchen, Allan; Jerde, Eric A.; Mckay, David S.; Graf, John; Oder, Robin R.

    1993-01-01

    The rocks and soils of the Moon will be the raw materials for fuels and construction needs at a lunar base. This includes sources of materials for the generation of hydrogen, oxygen, metals, and other potential construction materials. For most of the bulk material needs, the regolith, and its less than 1 cm fraction, the soil, will suffice. But for specific mineral resources, it may be necessary to concentrate minerals from rocks or soils, and it is not always obvious which is the more appropriate feedstock. Besides an appreciation of site geology, the mineralogy and petrography of local rocks and soils is important for consideration of the resources which can provide feedstocks of ilmenite, glass, agglutinates, anorthite, etc. In such studies, it is very time-consuming and practically impossible to correlate particle counts (the traditional method of characterizing lunar soil petrography) with accurate modal analyses and with mineral associations in multi-mineralic grains. But x ray digital imaging, using x rays characteristic of each element, makes all this possible and much more (e.g., size and shape analysis). An application of beneficiation image analysis, in use in our lab (Oxford Instr. EDS and Cameca SX-50 EMP), was demonstrated to study mineral liberation from lunar rocks and soils. Results of x ray image analysis are presented.

  19. Crosswell Seismic Amplitude-Versus-Offset for Detailed Imaging of Facies and Fluid Distribution within Carbonate Oil Reservoirs

    SciTech Connect

    Wayne Pennington; Mohamed Ibrahim; Roger Turpening; Sean Trisch; Josh Richardson; Carol Asiala; Walid Mabrouk

    2008-09-30

    Crosswell seismic surveys were conducted at two fields in northern Michigan. One of these, Springdale, included two monitor wells that are located external to the reef, and the other, Coldspring, employed two production wells within the reef. The Springdale wells extended to much greater depths than the reef, and imaging was conducted from above and from beneath the reef. The resulting seismic images provide the best views of pinnacle Niagaran reefs obtained to date. The tops of the reservoirs can be clearly distinguished, and their lateral extent or dipping edges can be observed along the profile. Reflecting events internal to the reef are evident; some of them are fairly continuous across the reef and others are discontinuous. Inversion of the seismic data indicates which events represent zones of higher porosity and which are lower porosity or even anhydrite plugged. The full stacked image includes angles that are beyond critical for many of the interfaces, and some reflections are visible only for a small range of angles, presumably near their critical angle. Stacking these angles in provides an opportunity for these events to be seen on the stacked image, where otherwise they would have been unrecognized. For inversion, however, the complexity associated with phase changes beyond critical can lead to poor results, and elastic inversion of partial angle stacks may be best conducted with restrictions to angles less than critical. Strong apparent attenuation of signals occurs when seismic ray paths pass through the upper part of the Springdale reservoir; this may be due to intrinsic attenuation and/or scattering of events due to the locally strongly varying gas saturation and extremely low fluid pressures. Signal-to-noise limitations become evident far from the source well in the Coldspring study, probably because the raw data were strongly affected by tube-wave noise generated by flow through the perforation of the receiver well. The seismic images obtained, and

  20. Detailed in situ laser calibration of the infrared imaging video bolometer for the JT-60U tokamak

    SciTech Connect

    Parchamy, H.; Peterson, B. J.; Konoshima, S.; Hayashi, H.; Seo, D. C.; Ashikawa, N

    2006-10-15

    The infrared imaging video bolometer (IRVB) in JT-60U includes a single graphite-coated gold foil with an effective area of 9x7 cm{sup 2} and a thickness of 2.5 {mu}m. The thermal images of the foil resulting from the plasma radiation are provided by an IR camera. The calibration technique of the IRVB gives confidence in the absolute levels of the measured values of the plasma radiation. The in situ calibration is carried out in order to obtain local foil properties such as the thermal diffusivity {kappa} and the product of the thermal conductivity k and the thickness t{sub f} of the foil. These quantities are necessary for solving the two-dimensional heat diffusion equation of the foil which is used in the experiments. These parameters are determined by comparing the measured temperature profiles (for kt{sub f}) and their decays (for {kappa}) with the corresponding results of a finite element model using the measured HeNe laser power profile as a known radiation power source. The infrared camera (Indigo/Omega) is calibrated by fitting the temperature rise of a heated plate to the resulting camera data using the Stefan-Boltzmann law.

  1. Academic detailing.

    PubMed

    Shankar, P R; Jha, N; Piryani, R M; Bajracharya, O; Shrestha, R; Thapa, H S

    2010-01-01

    There are a number of sources available to prescribers to stay up to date about medicines. Prescribers in rural areas in developing countries however, may not able to access some of them. Interventions to improve prescribing can be educational, managerial, and regulatory or use a mix of strategies. Detailing by the pharmaceutical industry is widespread. Academic detailing (AD) has been classically seen as a form of continuing medical education in which a trained health professional such as a physician or pharmacist visits physicians in their offices to provide evidence-based information. Face-to-face sessions, preferably on an individual basis, clear educational and behavioural objectives, establishing credibility with respect to objectivity, stimulating physician interaction, use of concise graphic educational materials, highlighting key messages, and when possible, providing positive reinforcement of improved practices in follow-up visits can increase success of AD initiatives. AD is common in developed countries and certain examples have been cited in this review. In developing countries the authors have come across reports of AD in Pakistan, Sudan, Argentina and Uruguay, Bihar state in India, Zambia, Cuba, Indonesia and Mexico. AD had a consistent, small but potentially significant impact on prescribing practices. AD has much less resources at its command compared to the efforts by the industry. Steps have to be taken to formally start AD in Nepal and there may be specific hindering factors similar to those in other developing nations. PMID:21209521

  2. Impact of more detailed categorization of shrinkage or progression ratio at initial imaging response after sorafenib treatment in advanced hepatocellular carcinoma patients

    PubMed Central

    Wada, Yoshiyuki; Takami, Yuko; Tateishi, Masaki; Ryu, Tomoki; Mikagi, Kazuhiro; Saitsu, Hideki

    2015-01-01

    Background Sorafenib therapy improves survival in unresectable hepatocellular carcinoma (HCC) patients without an objective response. The present study investigated whether the initial imaging response might be a prognostic indicator after administration of sorafenib therapy in HCC patients. Patients and methods This retrospective study reviewed unresectable HCC patients undergoing sorafenib therapy. Patients evaluated without complete response, partial response (PR), or progressive disease (PD) at the initial imaging response evaluation by modified Response Evaluation Criteria in Solid Tumors were divided into three groups according to more detailed categorization of the shrinkage/progression ratio in initial imaging response. A comparison of progression-free and overall survival among these groups was performed. Results Of the 43 non-PR non-PD patients with target lesions, ten (23.3%) exhibited mild response (MR; −30% to −5%), 14 (32.6%) exhibited no change (NC; −5% to +5%), and 19 (44.2%) exhibited mild-PD (MPD; +5% to +20%). There was no statistical difference in progression-free or overall survival between MR and NC patients. The median progression-free survivals in NC+MR and mild-PD patients were 15.0 and 5.3 months, respectively (P<0.01), and the median survival times were 31.9 and 17.1 months, respectively (P<0.001). In multivariate analysis, etiology (hepatitis C virus) and initial imaging response (MR+NC) was identified as an independently good prognostic factor. Conclusion More detailed categorization of shrinkage or progression at the initial imaging response evaluation may be a useful marker for predicting sorafenib treatment outcomes in HCC patients. If the initial imaging response is not progression but stability, sorafenib may have a survival benefit. PMID:26586953

  3. Computed tomography:the details.

    SciTech Connect

    Doerry, Armin Walter

    2007-07-01

    Computed Tomography (CT) is a well established technique, particularly in medical imaging, but also applied in Synthetic Aperture Radar (SAR) imaging. Basic CT imaging via back-projection is treated in many texts, but often with insufficient detail to appreciate subtleties such as the role of non-uniform sampling densities. Herein are given some details often neglected in many texts.

  4. Characterizing accuracy of total hemoglobin recovery using contrast-detail analysis in 3D image-guided near infrared spectroscopy with the boundary element method

    PubMed Central

    Ghadyani, Hamid R.; Srinivasan, Subhadra; Pogue, Brian W.; Paulsen, Keith D.

    2010-01-01

    The quantification of total hemoglobin concentration (HbT) obtained from multi-modality image-guided near infrared spectroscopy (IG-NIRS) was characterized using the boundary element method (BEM) for 3D image reconstruction. Multi-modality IG-NIRS systems use a priori information to guide the reconstruction process. While this has been shown to improve resolution, the effect on quantitative accuracy is unclear. Here, through systematic contrast-detail analysis, the fidelity of IG-NIRS in quantifying HbT was examined using 3D simulations. These simulations show that HbT could be recovered for medium sized (20mm in 100mm total diameter) spherical inclusions with an average error of 15%, for the physiologically relevant situation of 2:1 or higher contrast between background and inclusion. Using partial 3D volume meshes to reduce the ill-posed nature of the image reconstruction, inclusions as small as 14mm could be accurately quantified with less than 15% error, for contrasts of 1.5 or higher. This suggests that 3D IG-NIRS provides quantitatively accurate results for sizes seen early in treatment cycle of patients undergoing neoadjuvant chemotherapy when the tumors are larger than 30mm. PMID:20720975

  5. Uncooled VOx thermal imaging systems at BAE Systems

    NASA Astrophysics Data System (ADS)

    Blackwell, Richard; Lacroix, Daniel; Bach, Tuyet; Ishii, Jonathan; Hyland, Sandra; Geneczko, Jeannie; Chan, Sherman; Sujlana, Balwinder; Joswick, Mike

    2008-04-01

    BAE Systems has advanced its 17 μm pitch LWIR 640 x 480 microbolometer technology with improvements in pixel performance and introduction of a new 17 μm pitch ROIC. We have fabricated, characterized, and demonstrated high-yielding 17 μm pitch FPAs using our new ROIC, and have successfully demonstrated them at the system level. This new technology builds on our 28 μm FPA production experience and implements our high-performance single-level microbolometer process at 17 μm pitch. We present initial results and imagery. These 17 μm FPAs have exceptional performance and provide the path to next generation microbolometer applications.

  6. Detailed modeling and laser-induced fluorescence imaging of nitric oxide in a NH(i)-seeded non-premixed methane/air flame

    SciTech Connect

    Bell, John B.; Day, Marcus S.; Grcar, Joseph F.; Bessler, Wolfgang G.; Schulz, Christof; Glarborg, Peter; Jensen, Anker D.

    2001-12-14

    In this paper we study the formation of NO in laminar, nitrogen diluted methane diffusion flames that are seeded with ammonia in the fuel stream. We have performed numerical simulations with detailed chemistry as well as laser-induced fluorescence imaging measurements for a range of ammonia injection rates. For comparison with the experimental data, synthetic LIF images are calculated based on the numerical data accounting for temperature and fluorescence quenching effects. We demonstrate good agreement between measurements and computations. The LIF corrections inferred from the simulation are then used to calculate absolute NO mole fractions from the measured signal.The NO formation in both doped and undoped flames occurs in the flame sheet. In the undoped flame, four different mechanisms including thermal and prompt NO appear to contribute to NO formation. As the NH3 seeding level increases, fuel-NO becomes the dominant mechanism and N2 shifts from being a net reactant to being a net product. Nitric oxide in the undoped flame as well as in the core region of the doped flames are underpredicted by the model; we attribute this mainly to inaccuracies in the NO recycling chemistry on the fuel-rich side of the flame sheet.

  7. Performance improvements for VOx microbolometer FPAs

    NASA Astrophysics Data System (ADS)

    Murphy, Daniel F.; Ray, Michael; Wyles, Jessica; Asbrock, James F.; Hewitt, C.; Wyles, Richard; Gordon, Eli; Sessler, T.; Kennedy, Adam; Baur, Stefan T.; Van Lue, David; Anderson, Steven; Chin, Richard; Gonzales, H.; Le Pere, C.; Ton, S.; Kostrzewa, Thomas

    2004-08-01

    Raytheon is producing high-quality 320 x 240 microbolometer FPAs with 25 μm pitch pixels. The 320 x 240 FPAs have a sensitivity that is comparable to microbolometer FPAs with 50 μm pixels. Typical NETD values for these FPAs are <50mK with an f/1 aperture and operating at 30 Hz frame rates. Pixel operability is greater than 99.9% on most FPAs, and uncorrected responsivity nonuniformity is less than 4% (sigma/mean). These 25 μm microbolometer detectors also have a relatively fast thermal time constant of approximately 10 msec. These arrays have produced excellent image quality, and are currently fielded in a variety of demonstration systems. The pixel size reduction facilitates a significant FPA cost reduction since the number of die printed on a wafer can be increased, and also has enabled the development of a large-format 640 x 480 FPA array. Raytheon is producing these arrays with excellent sensitivity and typical NETD values of <50mK with an f/1 aperture and operating at 30 Hz frame rates. These arrays have excellent operability and image quality. Several dual FOV prototype 640 x 480 systems have been delivered under the LCMS and UAV programs. RVS has developed a flexible uncooled front end (UFE) electronics that will serve as the basis for the camera engine systems using 320 x 240 arrays. RVS has developed a 640 x 480 Common Uncooled Engine (CUE) which is intended for small pixel, high performance applications. The CUE is the ideal cornerstone for ground and airborne systems, multi-mode sensor, weapon sight or seeker architectures, and commercial surveillance.

  8. Cydonia Region - detail

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Detail cut out of PIA01235, Mars Orbiter Camera (MOC) image of a 4.42 by 82.94 km area of the Cydonia Region. The left image is raw, the right has been filtered and contrast enhanced.

    Orbit: 220

    Range: 444.21 km

    Resolution: 4.32 m/pixel

    Emission angle: 44.66 degrees

    Incidence angle: 64.96 degrees

    Phase angle: 61.97 degrees

    Scan rate: 0.1 degree/sec

    Start time: periapsis + 375 sec

    Sequence submitted to JPL: Sat 04/04/98 15:15 PST

    Image acquired by MOC: Sun 04/05/98 00:39:37 PST

    Data retrieved from JPL: Mon 04/06/98 09:05 PDT

  9. South Polar Details

    NASA Technical Reports Server (NTRS)

    2005-01-01

    22 September 2005 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows details among some of the eroded layer outcrops of the martian south polar region. Much of the south polar region of Mars is covered by a thick unit of layered material. For decades, the layers have been assumed to consist of a mixture of dust and ice, but it is equally possible that the materials are sedimentary rocks. This image was captured during southern spring, at a time when some of the surface was still covered by seasonal carbon dioxide (CO2) frost.

    Location near: 86.5oS, 116.6oW Image width: width: 3 km (1.9 mi) Illumination from: upper left Season: Southern Spring

  10. Magnetic resonance imaging reveals detailed spatial and temporal distribution of iron-based nanoparticles transported through water-saturated porous media.

    PubMed

    Cuny, Laure; Herrling, Maria Pia; Guthausen, Gisela; Horn, Harald; Delay, Markus

    2015-11-01

    The application of engineered nanoparticles (ENP) such as iron-based ENP in environmental systems or in the human body inevitably raises the question of their mobility. This also includes aspects of product optimization and assessment of their environmental fate. Therefore, the key aim was to investigate the mobility of iron-based ENP in water-saturated porous media. Laboratory-scale transport experiments were conducted using columns packed with quartz sand as model solid phase. Different superparamagnetic iron oxide nanoparticles (SPION) were selected to study the influence of primary particle size (d(P)=20 nm and 80 nm) and surface functionalization (plain, -COOH and -NH2 groups) on particle mobility. In particular, the influence of natural organic matter (NOM) on the transport and retention behaviour of SPION was investigated. In our approach, a combination of conventional breakthrough curve (BTC) analysis and magnetic resonance imaging (MRI) to non-invasively and non-destructively visualize the SPION inside the column was applied. Particle surface properties (surface functionalization and resulting zeta potential) had a major influence while their primary particle size turned out to be less relevant. In particular, the mobility of SPION was significantly increased in the presence of NOM due to the sorption of NOM onto the particle surface resulting in a more negative zeta potential. MRI provided detailed spatially resolved information complementary to the quantitative BTC results. The approach can be transferred to other porous systems and contributes to a better understanding of particle transport in environmental porous media and porous media in technical applications. PMID:26335945

  11. Magnetic resonance imaging reveals detailed spatial and temporal distribution of iron-based nanoparticles transported through water-saturated porous media

    NASA Astrophysics Data System (ADS)

    Cuny, Laure; Herrling, Maria Pia; Guthausen, Gisela; Horn, Harald; Delay, Markus

    2015-11-01

    The application of engineered nanoparticles (ENP) such as iron-based ENP in environmental systems or in the human body inevitably raises the question of their mobility. This also includes aspects of product optimization and assessment of their environmental fate. Therefore, the key aim was to investigate the mobility of iron-based ENP in water-saturated porous media. Laboratory-scale transport experiments were conducted using columns packed with quartz sand as model solid phase. Different superparamagnetic iron oxide nanoparticles (SPION) were selected to study the influence of primary particle size (dP = 20 nm and 80 nm) and surface functionalization (plain, -COOH and -NH2 groups) on particle mobility. In particular, the influence of natural organic matter (NOM) on the transport and retention behaviour of SPION was investigated. In our approach, a combination of conventional breakthrough curve (BTC) analysis and magnetic resonance imaging (MRI) to non-invasively and non-destructively visualize the SPION inside the column was applied. Particle surface properties (surface functionalization and resulting zeta potential) had a major influence while their primary particle size turned out to be less relevant. In particular, the mobility of SPION was significantly increased in the presence of NOM due to the sorption of NOM onto the particle surface resulting in a more negative zeta potential. MRI provided detailed spatially resolved information complementary to the quantitative BTC results. The approach can be transferred to other porous systems and contributes to a better understanding of particle transport in environmental porous media and porous media in technical applications.

  12. Detail of Triton

    NASA Technical Reports Server (NTRS)

    1998-01-01

    This color photo of Neptune's large satellite Triton was obtained on Aug. 24 1989 at a range of 530,000 kilometers (330,000 miles). The resolution is about 10 kilometers (6.2 miles), sufficient to begin to show topographic detail. The image was made from pictures taken through the green, violet and ultraviolet filters. In this technique, regions that are highly reflective in the ultraviolet appear blue in color. In reality, there is no part of Triton that would appear blue to the eye. The bright southern hemisphere of Triton, which fills most of this frame, is generally pink in tone as is the even brighter equatorial band. The darker regions north of the equator also tend to be pink or reddish in color. JPL manages the Voyager project for NASA's Office of Space Science, Washington, DC.

  13. Pin-hole array production and detailed data analysis for advanced single-shot X-ray imaging of laboratory plasmas

    NASA Astrophysics Data System (ADS)

    Levato, T.; Labate, L.; Pathak, N. C.; Cecchetti, C.; Koester, P.; Di Fabrizio, E.; Delogu, P.; Giulietti, A.; Giulietti, D.; Gizzi, L. A.

    2010-11-01

    Laser produced plasmas offer the unique opportunity to investigate physical mechanisms working at extremely high field in pulsed regime [1] (Gizzi et al., 2009). Future large scale infrastructure like HiPER and ELI may open new frontiers of knowledge in this way. Technologies needed for improving diagnostic in this field have a strong impact on a wide range of multi-disciplinary applications as for compact plasma-based accelerators [1,2] (Gizzi et al., 2009; Betti et al., 2009) laser fusion oriented experiments, three-dimensional microscopy and lithography. As an example the X-ray imaging, being a powerful diagnostic tool for deep investigation on different variety of laser produced plasma, has obtained a grooving effort in recent years. Large scale facilities working in single-pulse regime for laser fusion oriented experiments have evidenced the necessity to obtain spectrally resolved X-ray images of produced plasmas in a single shot. By combining the charge coupled devices (CCD) based single-photon detection technique with a pin-hole array (PHA) a new diagnostic technique was developed, as shown in recent experiments related to the European HiPER project [3] (Labate et al., 2009). Here we qualitatively describe the PHA production process on a heavy metal substrate by means of SEM images that show an internal diameter on the micrometer scale and an aspect ratio of about 20. The characterization of the X-ray contrast up to 90 keV is presented. The data analysis of the X-ray photons interaction on CCD, for spectrum reconstruction up to high energy, is described [4] (Levato et al., 2008).

  14. A DETAILED GRAVITATIONAL LENS MODEL BASED ON SUBMILLIMETER ARRAY AND KECK ADAPTIVE OPTICS IMAGING OF A HERSCHEL-ATLAS SUBMILLIMETER GALAXY AT z = 4.243 {sup ,} {sup ,}

    SciTech Connect

    Bussmann, R. S.; Gurwell, M. A.; Fu Hai; Cooray, A.; Smith, D. J. B.; Bonfield, D.; Dunne, L.; Dye, S.; Eales, S.; Auld, R.; Baes, M.; Fritz, J.; Baker, A. J.; Cava, A.; Clements, D. L.; Dariush, A.; Coppin, K.; Dannerbauer, H.; De Zotti, G.; Hopwood, R.; and others

    2012-09-10

    We present high-spatial resolution imaging obtained with the Submillimeter Array (SMA) at 880 {mu}m and the Keck adaptive optics (AO) system at the K{sub S}-band of a gravitationally lensed submillimeter galaxy (SMG) at z = 4.243 discovered in the Herschel Astrophysical Terahertz Large Area Survey. The SMA data (angular resolution Almost-Equal-To 0.''6) resolve the dust emission into multiple lensed images, while the Keck AO K{sub S}-band data (angular resolution Almost-Equal-To 0.''1) resolve the lens into a pair of galaxies separated by 0.''3. We present an optical spectrum of the foreground lens obtained with the Gemini-South telescope that provides a lens redshift of z{sub lens} = 0.595 {+-} 0.005. We develop and apply a new lens modeling technique in the visibility plane that shows that the SMG is magnified by a factor of {mu} = 4.1 {+-} 0.2 and has an intrinsic infrared (IR) luminosity of L{sub IR} = (2.1 {+-} 0.2) Multiplication-Sign 10{sup 13} L{sub Sun }. We measure a half-light radius of the background source of r{sub s} = 4.4 {+-} 0.5 kpc which implies an IR luminosity surface density of {Sigma}{sub IR} (3.4 {+-} 0.9) Multiplication-Sign 10{sup 11} L{sub Sun} kpc{sup -2}, a value that is typical of z > 2 SMGs but significantly lower than IR luminous galaxies at z {approx} 0. The two lens galaxies are compact (r{sub lens} Almost-Equal-To 0.9 kpc) early-types with Einstein radii of {theta}{sub E1} 0.57 {+-} 0.01 and {theta}{sub E2} = 0.40 {+-} 0.01 that imply masses of M{sub lens1} = (7.4 {+-} 0.5) Multiplication-Sign 10{sup 10} M{sub Sun} and M{sub lens2} = (3.7 {+-} 0.3) Multiplication-Sign 10{sup 10} M{sub Sun }. The two lensing galaxies are likely about to undergo a dissipationless merger, and the mass and size of the resultant system should be similar to other early-type galaxies at z {approx} 0.6. This work highlights the importance of high spatial resolution imaging in developing models of strongly lensed galaxies discovered by Herschel.

  15. Third-generation imaging sensor system concepts

    NASA Astrophysics Data System (ADS)

    Reago, Donald A.; Horn, Stuart B.; Campbell, James, Jr.; Vollmerhausen, Richard H.

    1999-07-01

    Second generation forward looking infrared sensors, based on either parallel scanning, long wave (8 - 12 um) time delay and integration HgCdTe detectors or mid wave (3 - 5 um), medium format staring (640 X 480 pixels) InSb detectors, are being fielded. The science and technology community is now turning its attention toward the definition of a future third generation of FLIR sensors, based on emerging research and development efforts. Modeled third generation sensor performance demonstrates a significant improvement in performance over second generation, resulting in enhanced lethality and survivability on the future battlefield. In this paper we present the current thinking on what third generation sensors systems will be and the resulting requirements for third generation focal plane array detectors. Three classes of sensors have been identified. The high performance sensor will contain a megapixel or larger array with at least two colors. Higher operating temperatures will also be the goal here so that power and weight can be reduced. A high performance uncooled sensor is also envisioned that will perform somewhere between first and second generation cooled detectors, but at significantly lower cost, weight, and power. The final third generation sensor is a very low cost micro sensor. This sensor can open up a whole new IR market because of its small size, weight, and cost. Future unattended throwaway sensors, micro UAVs, and helmet mounted IR cameras will be the result of this new class.

  16. Rossby-wave driven stirring of the UTLS - a detailed view on the intricately layered structure by the 3-D imaging limb-sounder GLORIA

    NASA Astrophysics Data System (ADS)

    Ungermann, J.; Friedl-Vallon, F.; Hoepfner, M.; Oelhaf, H.; Preusse, P.; Riese, M.

    2014-12-01

    The Gimballed Limb Radiance Imager of the Atmosphere (GLORIA) is a new instrument that combines a classical Fourier transform spectrometer (FTS) with a 2-D detector array. Imaging allows the spatial sampling to be improved by up to an order of magnitude when compared to a limb scanning instrument. GLORIA is designed to operate on various high altitude research platforms. The instrument is a joint development of the German Helmholtz Large Research Facilities Karlsruhe Institute of Technology (KIT) and Research Centre Juelich (FZJ). GLORIA builds upon the heritage of KIT and FZJ in developing and operating IR limb sounders (MIPAS, CRISTA). In Summer 2012, GLORIA was an integral part of the first large missions for the German research aircraft HALO dedicated to atmospheric research, TACTS and ESMVAL. The data span latitudes from 80°N to 65°S and include several tomographic flight patterns that allow the 3-D reconstruction of observed air masses. We provide an overview of the heterogeneous structure of the upper troposphere/lower stratosphere (UTLS) as observed over Europe. Retrieved water vapor and ozone are used to identify the tropospheric or stratospheric character of air masses and can thus be used to visualize the multi-species 2-D (and partly 3-D) chemical structure of the UTLS. A highly intricate structure is found consisting often of fine-scale layers extending only several hundred meters in the vertical. These horizontally large-scale structures are thus below the typical vertical resolution of current chemistry climate models. Trajectory studies reveal the origin of the filaments to be Rossby wave-breaking events over the Pacific and Atlantic that cause tropical air stemming from the general area of the Asian monsoon to be mixed across the jet-stream into the subtropical lowermost stratosphere. These results demonstrate a rich spatial structure of the UTLS region at the subtropical jet, where the tropopause break is perturbed by breaking Rossby waves. The

  17. It's time for a crisper image of the Face of the Earth: Landsat and climate time series for massive land cover & climate change mapping at detailed resolution.

    NASA Astrophysics Data System (ADS)

    Pons, Xavier; Miquel, Ninyerola; Oscar, González-Guerrero; Cristina, Cea; Pere, Serra; Alaitz, Zabala; Lluís, Pesquer; Ivette, Serral; Joan, Masó; Cristina, Domingo; Maria, Serra Josep; Jordi, Cristóbal; Chris, Hain; Martha, Anderson; Juanjo, Vidal

    2014-05-01

    Combining climate dynamics and land cover at a relative coarse resolution allows a very interesting approach to global studies, because in many cases these studies are based on a quite high temporal resolution, but they may be limited in large areas like the Mediterranean. However, the current availability of long time series of Landsat imagery and spatially detailed surface climate models allow thinking on global databases improving the results of mapping in areas with a complex history of landscape dynamics, characterized by fragmentation, or areas where relief creates intricate climate patterns that can be hardly monitored or modeled at coarse spatial resolutions. DinaCliVe (supported by the Spanish Government and ERDF, and by the Catalan Government, under grants CGL2012-33927 and SGR2009-1511) is the name of the project that aims analyzing land cover and land use dynamics as well as vegetation stress, with a particular emphasis on droughts, and the role that climate variation may have had in such phenomena. To meet this objective is proposed to design a massive database from long time series of Landsat land cover products (grouped in quinquennia) and monthly climate records (in situ climate data) for the Iberian Peninsula (582,000 km2). The whole area encompasses 47 Landsat WRS2 scenes (Landsat 4 to 8 missions, from path 197 to 202 and from rows 30 to 34), and 52 Landsat WRS1 scenes (for the previous Landsat missions, 212 to 221 and 30 to 34). Therefore, a mean of 49.5 Landsat scenes, 8 quinquennia per scene and a about 6 dates per quinquennium , from 1975 to present, produces around 2376 sets resulting in 30 m x 30 m spatial resolution maps. Each set is composed by highly coherent geometric and radiometric multispectral and multitemporal (to account for phenology) imagery as well as vegetation and wetness indexes, and several derived topographic information (about 10 Tbyte of data). Furthermore, on the basis on a previous work: the Digital Climatic Atlas of

  18. Imaging Magma Under St. Helens (iMUSH): Details of passive-source seismic deployment and preliminary 3-D velocity structure

    NASA Astrophysics Data System (ADS)

    Ulberg, C. W.; Creager, K. C.; Moran, S. C.; Abers, G. A.; Denlinger, R. P.; Hotovec-Ellis, A. J.; Vidale, J. E.; Kiser, E.; Levander, A.; Schultz, A.

    2014-12-01

    The imaging Magma Under St. Helens (iMUSH) experiment aims to delineate the extent of the magmatic system beneath Mount St. Helens (MSH) in Washington State. The experiment involves active- and passive-source seismology, magnetotellurics, and geochemistry/petrology. Seventy passive-source broadband seismometers were deployed in a 100-km-diameter array centered on MSH, with an average spacing of 10 km, and a planned duration of two years. The deployment over two weeks in June 2014 involved a group of 18 people split into 6 teams. Approximately half of the seismic stations have aircell batteries and/or pole-mounted solar panels in order to maintain power through deep snow at higher elevations during the winter months. Data will be retrieved 2-4 times a year throughout the duration of the experiment. The first service run performed in mid-July 2014 had a 98.4% data recovery. This is one of the largest wide-aperture two-dimensional arrays covering a volcano anywhere. The active-source portion of the experiment successfully set off 23 shots in late-July 2014. These were recorded clearly at permanent stations run by the Pacific Northwest Seismic Network up to 200 km away, and are expected to be well-recorded on many of the 70 broadband seismometers in addition to the 2500 Reftek "Texans" deployed temporarily for this purpose. For the 2-4 weeks of broadband data collected in July, local earthquakes down to magnitude 0 are recorded across the array, with clear P- and S- arrivals. Earthquakes of this size occur daily within 50 km of MSH. We are keeping a careful catalog of all activity in the region for the duration of the iMUSH experiment. We will pick P- and S-wave travel times at the 70 broadband stations from local earthquakes and active shots, for available data from between June and October 2014. We will also use a tomographic code (Preston et al, 2003, Science) to invert the travel times to obtain preliminary earthquake location and 3-D velocity structure.

  19. Revealing Small-Scale Details

    NASA Astrophysics Data System (ADS)

    Crawford, Ken

    Astrophotographers face amazing challenges in their pursuit of acquiring high quality data and then turn that data into beautiful images that viewers admire. We carefully set up our imaging systems with amazing precision so each exposure contains well focused sharp sub frames. For every exposure there exist a myriad of variables that can work against us to potentially degrade the details of the celestial objects we record. Some of these variables are within our control and some are not. Even the variables beyond our control can often be compensated for by processing adjustments for maximizing the potential of our images. My goal is to share some of the methods I have found useful in recovering those elements that bring clarity to our pictures.

  20. Detail One Half of Wood Truss, Detail One Quarter Plan ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail One Half of Wood Truss, Detail One Quarter Plan of Floor Beams & Bottom Truss Cord, Detail at A Plan, Detail at B Plan - Covered Bridge, Spanning Darby Creek, North Lewisburg, Champaign County, OH

  1. Chord Splicing & Joining Detail; Chord & CrossBracing Joint Details; ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Chord Splicing & Joining Detail; Chord & Cross-Bracing Joint Details; Cross Bracing Center Joint Detail; Chord & Diagonal Joint Detail - Vermont Covered Bridge, Highland Park, spanning Kokomo Creek at West end of Deffenbaugh Street (moved to), Kokomo, Howard County, IN

  2. Arch & Chord Joint Detail; Crossbracing Center Joint Detail; Chord, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Arch & Chord Joint Detail; Crossbracing Center Joint Detail; Chord, Panel Post, Tie & Diagonal Brace Joint Detail; Chord, Panel Post, Tie & Crossbracing Joint Detail - Dunlapsville Covered Bridge, Spanning East Fork Whitewater River, Dunlapsville, Union County, IN

  3. LF460 detail design

    NASA Technical Reports Server (NTRS)

    1971-01-01

    This is the final technical report documenting the detail design of the LF460, and advanced turbotip lift fan intended for application with the YJ97-GE-100 turbojet jet generator to a V/STOL transport research aircraft. Primary objective of the design was to achieve a low noise level while maintaining the high thrust/weight ratio capability of a high pressure ratio lift fan. Report covers design requirements and summarizes activities and final results in the areas of aerodynamic and mechanical design, component and system performance, acoustic features and final noise predictions.

  4. Details of meiosis

    SciTech Connect

    1993-12-31

    Chapter 18, discusses the details of meiosis, beginning with the structure and number of chiasmata, i.e., the cytological term for two homologous chromosomes forming a bivalent which begin to repel each other until they are held together only at the point of crossing-over. The synaptonemal complex which consists of two lateral elements which contain protein and RNA is also discussed. The chapter concludes with a description of meiosis in polyploids, human meiosis, and the behavior of X and Y chromosomes. 28 refs., 8 figs.

  5. Detailed Debunking of Denial

    NASA Astrophysics Data System (ADS)

    Enting, I. G.; Abraham, J. P.

    2012-12-01

    The disinformation campaign against climate science has been compared to a guerilla war whose tactics undermine the traditional checks and balances of science. One comprehensive approach has to been produce archives of generic responses such as the websites of RealClimate and SkepticalScience. We review our experiences with an alternative approach of detailed responses to a small number of high profile cases. Our particular examples were Professor Ian Plimer and Christopher Monckton, the Third Viscount Monckton of Brenchley, each of whom has been taken seriously by political leaders in our respective countries. We relate our experiences to comparable examples such as John Mashey's analysis of the Wegman report and the formal complaints about Lomborg's "Skeptical Environmentalist" and Durkin's "Great Global Warming Swindle". Our two approaches used contrasting approaches: an on-line video of a lecture vs an evolving compendium of misrepresentations. Additionally our approaches differed in the emphasis. The analysis of Monckton concentrated on the misrepresentation of the science, while the analysis of Plimer concentrated on departures from accepted scientific practice: fabrication of data, misrepresentation of cited sources and unattributed use of the work of others. Benefits of an evolving compendium were the ability to incorporate contributions from members of the public who had identified additional errors and the scope for addressing new aspects as they came to public attention. `Detailed debunking' gives non-specialists a reference point for distinguishing non-science when engaging in public debate.

  6. Horizontal Cross Bracing Detail, Vertical Cross Bracing Detail, Horizontal Cross ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Horizontal Cross Bracing Detail, Vertical Cross Bracing Detail, Horizontal Cross Bracing Joint, Vertical Cross Bracing End Detail - Ceylon Covered Bridge, Limberlost Park, spanning Wabash River at County Road 900 South, Geneva, Adams County, IN

  7. Crowdsourcing detailed flood data

    NASA Astrophysics Data System (ADS)

    Walliman, Nicholas; Ogden, Ray; Amouzad*, Shahrzhad

    2015-04-01

    Over the last decade the average annual loss across the European Union due to flooding has been 4.5bn Euros, but increasingly intense rainfall, as well as population growth, urbanisation and the rising costs of asset replacements, may see this rise to 23bn Euros a year by 2050. Equally disturbing are the profound social costs to individuals, families and communities which in addition to loss of lives include: loss of livelihoods, decreased purchasing and production power, relocation and migration, adverse psychosocial effects, and hindrance of economic growth and development. Flood prediction, management and defence strategies rely on the availability of accurate information and flood modelling. Whilst automated data gathering (by measurement and satellite) of the extent of flooding is already advanced it is least reliable in urban and physically complex geographies where often the need for precise estimation is most acute. Crowdsourced data of actual flood events is a potentially critical component of this allowing improved accuracy in situations and identifying the effects of local landscape and topography where the height of a simple kerb, or discontinuity in a boundary wall can have profound importance. Mobile 'App' based data acquisition using crowdsourcing in critical areas can combine camera records with GPS positional data and time, as well as descriptive data relating to the event. This will automatically produce a dataset, managed in ArcView GIS, with the potential for follow up calls to get more information through structured scripts for each strand. Through this local residents can provide highly detailed information that can be reflected in sophisticated flood protection models and be core to framing urban resilience strategies and optimising the effectiveness of investment. This paper will describe this pioneering approach that will develop flood event data in support of systems that will advance existing approaches such as developed in the in the UK

  8. roof truss detail, historic strap hinge detail Chopawamsic Recreational ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    roof truss detail, historic strap hinge detail - Chopawamsic Recreational Demonstration Area - Cabin Camp 1, Main Arts and Crafts Lodge, Prince William Forest Park, Triangle, Prince William County, VA

  9. double hung window details, hall window details, entrance door profiles ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    double hung window details, hall window details, entrance door profiles - Chopawamsic Recreational Demonstration Area - Cabin Camp 1, Help's Quarters, Prince William Forest Park, Triangle, Prince William County, VA

  10. Reply to the discussion by Pinyol et al. (2016) on Gutiérrez et al. (2015) "Large landslides associated with a diapiric fold in Canelles Reservoir (Spanish Pyrenees): Detailed geological-geomorphological mapping, trenching and electrical resistivity imaging"

    NASA Astrophysics Data System (ADS)

    Gutiérrez, Francisco; Linares, Rogelio; Roqué, Carles; Zarroca, Mario; Carbonel, Domingo; Rosell, Joan; Gutiérrez, Mateo

    2016-06-01

    Gutiérrez et al. (2015) in their paper published in Geomorphology document for the first time five large landslides (L1, L2, L3, L5, L6) in the Canelles Reservoir (Spanish Pyrenees) on the basis of detailed geomorphological-geological mapping. They also analyse a large 40 × 106 m3 translational landslide reactivated in 2006 by a severe decline in the reservoir water level (L4 or Canelles landslide). This landslide was discovered because a 1.1 km long fissure-scarp less than 0.5 m in width and height developed along the head of the landslide. The investigation concerning the Canelles landslide included the construction of site-specific stratigraphic columns, detailed mapping, electrical resistivity imaging, and trenching in the upper part of the landslide. The retrodeformation analysis of the trench log together with radiocarbon dates revealed two displacement events older and larger in magnitude than the 2006 event. Those episodes occurred in the 6th to 7th Centuries and in 1262-1679 yr AD, the latter one probably triggered by the 1373 Ribagorza earthquake (Mw 6.2). Based on these new data, Gutiérrez et al. (2015) discuss the hypothesis proposed in a previous paper by Pinyol et al. (2012) on the kinematic behaviour of the Canelles landslide. Pinyol et al. (2012), based on a thermo-hydro-mechanical numerical model that assumes dilation in the sliding surface induced by frictional heating under undrained conditions, predict a catastrophic reactivation. They forecast that at 35 s after the initiation of the movement, the landslide would reach a displacement of 250 m and a speed of 16 m s- 1, capable of generating an impulse-water wave (tsunami). Pinyol et al. (2016) address three issues in their discussion on Gutiérrez et al. (2015): (1) the geological model used; (2) the validity of the prediction of an extremely rapid reactivation; (3) the effectiveness of the corrective measures proposed. They also add a section with additional comments.

  11. Eros details enhanced by computer processing

    NASA Technical Reports Server (NTRS)

    2000-01-01

    The NEAR camera's ability to show details of Eros's surface is limited by the spacecraft's distance from the asteroid. That is, the closer the spacecraft is to the surface, the more that details are visible. However mission scientists regularly use computer processing to squeeze an extra measure of information from returned data. In a technique known as 'superresolution', many images of the same scene acquired at very, very slightly different camera pointing are carefully overlain and processed to bright out details even smaller than would normally be visible. In this rendition constructed out of 20 image frames acquired Feb. 12, 2000, the images have first been enhanced ('high-pass filtered') to accentuate small-scale details. Superresolution was then used to bring out features below the normal ability of the camera to resolve.

    Built and managed by The Johns Hopkins University Applied Physics Laboratory, Laurel, Maryland, NEAR was the first spacecraft launched in NASA's Discovery Program of low-cost, small-scale planetary missions. See the NEAR web page at http://near.jhuapl.edu for more details.

  12. Motion analysis of artery pulsation in neonatal cranial ultrasonogram

    NASA Astrophysics Data System (ADS)

    Fukuzawa, Masayuki; Kubo, Hiroki; Kitsunezuka, Yoshiki; Yamada, Masayoshi

    1999-05-01

    Using an optical-flow technique, we have quantitatively analyzed tissue motion due to artery pulsation accompanied with blood flow in a neonatal cranial ultrasonogram. The tissue motion vector was successfully calculated at each pixel in a series of echo images (32 frames, 640 X 480 pixels/frame, 8 bits/pixel, 33 ms/frame) taken in the brightness mode by using an ultrasound probe of 5.0 MHz. The optical-flow technique used was a gradient method combined with local optimization for 3 X 3 neighbors. From 2D mappings of tissue motion vectors and their time-sequence variations, it was found that the tissue motion due to artery pulsation revealed periodic to-and-fro motion synchronized with heartbeat (300 - 500 ms), clearly distinguishing from unwanted non-periodic motion due to the sway of neonatal head during diagnosis.

  13. Amorphous silicon based large format uncooled FPA microbolometer technology

    NASA Astrophysics Data System (ADS)

    Schimert, T.; Brady, J.; Fagan, T.; Taylor, M.; McCardel, W.; Gooch, R.; Ajmera, S.; Hanson, C.; Syllaios, A. J.

    2008-04-01

    This paper presents recent developments in next generation microbolometer Focal Plane Array (FPA) technology at L-3 Communications Infrared Products (L-3 CIP). Infrared detector technology at L-3 CIP is based on hydrogenated amorphous silicon (a-Si:H) and amorphous silicon germanium(a-SiGe:H). Large format high performance, fast, and compact IR FPAs are enabled by a low thermal mass pixel design; favorable material properties; an advanced ROIC design; and wafer level packaging. Currently at L-3 CIP, 17 micron pixel FPA array technology including 320x240, 640 x 480 and 1024 x768 arrays is under development. Applications of these FPAs range from low power microsensors to high resolution near-megapixel imager systems.

  14. Low-cost microsensors program

    NASA Astrophysics Data System (ADS)

    Anderson, John S.; Bradley, Daryl; Chen, Chungte W.; Chin, Richard; Jurgelewicz, K.; Radford, William A.; Kennedy, Adam; Murphy, Daniel F.; Ray, Michael; Wyles, Richard; Brown, James C.; Newsome, Gwendolyn W.

    2001-10-01

    The objectives of the Low Cost Microsensors (LCMS) Program are twofold. The first is to develop and deliver a long-range infrared (IR) sensor built upon an uncooled vanadium oxide (VOx) 640 X 512 format focal plane array (FPA) engine. The second is to develop an expendable microsensor built upon a VOx 160 X 128 format FPA engine. The 640 X 480 sensor is applicable to long-range surveillance and targeting missions and is a reusable asset. The 160 X 120 sensor is designed for applications where miniaturization is required as well as low cost and low power. The 160 X 120 is also intended for expendable military applications. The intent of this DUS&T effort is to further reduce the cost, weight, and power of uncooled IR sensors, and to increase the capability of these sensors, thereby expanding their applicability to military and commercial markets never before addressed by thermal imaging.

  15. Dual-monitor deterministic hardware for visual stimuli generation in neuroscience experiments.

    PubMed

    Gazziro, Mario; Almeida, Lirio

    2010-01-01

    This article describes the development of a dual-monitor visual stimulus generator that is used in neuroscience experiments with invertebrates such as flies. The experiment consists in the visualization of two fixed images that are displaced horizontally according to the stimulus data. The system was developed using off-the-shelf FPGA kits and it is capable of displaying 640x480 pixels with 256 intensity levels at 200 frames per second (FPS) on each monitor. A Raster plot of the experiment with the superimposed stimuli was generated as the result of this work. A novel architecture was developed, using the same DOT Clock for both monitors, and its implementation generates a perfect synchronism in both devices. PMID:21096378

  16. Detail, Scandia Hotel, view to southwest showing details of balloon ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail, Scandia Hotel, view to southwest showing details of balloon framing, including full two-story studs notched to carry girts supporting second story floor joists (210mm lens) - Scandia Hotel, 225 First Street, Eureka, Humboldt County, CA

  17. 56. DETAIL OF SOUTH SIDE OF WINDING SHEAVES: Detail of ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    56. DETAIL OF SOUTH SIDE OF WINDING SHEAVES: Detail of south side of the winding sheaves. These sheaves drive the California Street cable. - San Francisco Cable Railway, Washington & Mason Streets, San Francisco, San Francisco County, CA

  18. Detail view of ornamental lighting detail of southwest corner of ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail view of ornamental lighting detail of southwest corner of Sixth Street Bridge. Looking northeast - Sixth Street Bridge, Spanning 101 Freeway at Sixth Street, Los Angeles, Los Angeles County, CA

  19. Detail of pumps in troughs, detail of truss attachment ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail of pumps in troughs, detail of truss - attachment to the wall - as well as the troughs themselves. Interior of the main hatchery building, view to the east. - Prairie Creek Fish Hatchery, Hwy. 101, Orick, Humboldt County, CA

  20. 22. PIER NO. IV DETAIL, WITH DETAIL OF SOUTHWEST PORTAL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    22. PIER NO. IV DETAIL, WITH DETAIL OF SOUTHWEST PORTAL AND SOUTHEAST WEB OF THROUGH TRUSS; VIEW TO NORTH - Nebraska City Bridge, Spanning Missouri River near Highway 2 between Nebraska & Iowa, Nebraska City, Otoe County, NE

  1. Influences on physicians' adoption of electronic detailing (e-detailing).

    PubMed

    Alkhateeb, Fadi M; Doucette, William R

    2009-01-01

    E-detailing means using digital technology: internet, video conferencing and interactive voice response. There are two types of e-detailing: interactive (virtual) and video. Currently, little is known about what factors influence physicians' adoption of e-detailing. The objectives of this study were to test a model of physicians' adoption of e-detailing and to describe physicians using e-detailing. A mail survey was sent to a random sample of 2000 physicians practicing in Iowa. Binomial logistic regression was used to test the model of influences on physician adoption of e-detailing. On the basis of Rogers' model of adoption, the independent variables included relative advantage, compatibility, complexity, peer influence, attitudes, years in practice, presence of restrictive access to traditional detailing, type of specialty, academic affiliation, type of practice setting and control variables. A total of 671 responses were received giving a response rate of 34.7%. A total of 141 physicians (21.0%) reported using of e-detailing. The overall adoption model for using either type of e-detailing was found to be significant. Relative advantage, peer influence, attitudes, type of specialty, presence of restrictive access and years of practice had significant influences on physician adoption of e-detailing. The model of adoption of innovation is useful to explain physicians' adoption of e-detailing. PMID:19306198

  2. An Innovative Unmanned System for Advanced Environmental Monitoring: Design and Development

    NASA Astrophysics Data System (ADS)

    Marsella, Ennio; Giordano, Laura; Evangelista, Lorenza; Iengo, Antonio; di Filippo, Alessandro; Coppola, Aniello

    2015-04-01

    wind conditions, and a capability to survey an area of up to 5x5 square kilometers. The UAV payload consists of three different types of sensors: a laser scanner, a thermal-camera and an integrated camera reflex with gimbal. The laser scanner has 10 mm survey-grade accuracy and a field of view up to 330°. The thermal-camera has a resolution 640x480 pixels and a thermal sensitivity <20 mK (at 30 °C), while the reflex is a 22.3 Megapixel full-frame sensor. In addition to the common applications, such as generating mapping, charting, and geodesy products, the system allows performing real-time survey and monitoring of different natural risk under dangerous condition. The system is, also, address to environmental risk monitoring and prevention, industrial activity and emergency interventions related to environmental crises (i.e. oil spills).

  3. 13. DETAIL VIEW OF BRIDGE, LOOKING SOUTH FROM ROADWAY. DETAIL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    13. DETAIL VIEW OF BRIDGE, LOOKING SOUTH FROM ROADWAY. DETAIL VIEW OF THE PIERS AND LIGHTING FIXTURES ON THE COLORADO STREET BRIDGE. THIS VIEW SHOWS A PORTION OF THE BRIDGE ALONG THE SOUTH SIDE OF THE ROADWAY. EACH FIXTURE ALSO ORIGINALLY HAD FOUR ADDITIONAL GLOBES, WHICH EXTENDED FROM THE COLUMN BELOW THE MAIN GLOBE. THE 'REFUGE' SEATING AREAS ARE ORIGINAL, WHILE THE RAILING IS A LATER ADDITION. - Colorado Street Bridge, Spanning Arroyo Seco at Colorado Boulevard, Pasadena, Los Angeles County, CA

  4. 23. CREWS' BERTHING, SHOWING DETAIL OF INTERIOR LOCKING MECHANISM ON ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    23. CREWS' BERTHING, SHOWING DETAIL OF INTERIOR LOCKING MECHANISM ON HATCH DOOR (INTERIOR SIDE OF DOOR IN IMAGE 22). - U.S. Coast Guard Cutter WHITE HEATH, USGS Integrated Support Command Boston, 427 Commercial Street, Boston, Suffolk County, MA

  5. 17. DETAIL VIEW OF PORT SIDE ENGINE, BATTERIES, AND FUEL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    17. DETAIL VIEW OF PORT SIDE ENGINE, BATTERIES, AND FUEL TANK; INTERIOR OF SHIP'S HEAD SHOWN IN LEFT OF IMAGE - Pilot Schooner "Alabama", Moored in harbor at Vineyard Haven, Vineyard Haven, Dukes County, MA

  6. Hi-C: A Detailed View of the Sun

    NASA Video Gallery

    This 10-second movie includes imagery collected from the Atmospheric Imaging Assembly instrument flying on NASA's Solar Dynamics Observatory and Hi-C. Hi-C’s resolution is five times more detaile...

  7. 24. INTERIOR DETAIL FROM THE SOUTH END OF THE DELIVERY ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    24. INTERIOR DETAIL FROM THE SOUTH END OF THE DELIVERY (RECEIVING LEVEL. THE DETAIL SHOWS THE WINDING DRUM AND REVERSING CLUTCH FOR THE TRAMWAY ORE CAR, AND AN ORE CHUTE IN THE FLOOR) FOREGROUND BOTTOM LEFT OF THE IMAGE). - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

  8. NOSS Altimeter Detailed Algorithm specifications

    NASA Technical Reports Server (NTRS)

    Hancock, D. W.; Mcmillan, J. D.

    1982-01-01

    The details of the algorithms and data sets required for satellite radar altimeter data processing are documented in a form suitable for (1) development of the benchmark software and (2) coding the operational software. The algorithms reported in detail are those established for altimeter processing. The algorithms which required some additional development before documenting for production were only scoped. The algorithms are divided into two levels of processing. The first level converts the data to engineering units and applies corrections for instrument variations. The second level provides geophysical measurements derived from altimeter parameters for oceanographic users.

  9. Image

    2007-08-31

    The computer side of the IMAGE project consists of a collection of Perl scripts that perform a variety of tasks; scripts are available to insert, update and delete data from the underlying Oracle database, download data from NCBI's Genbank and other sources, and generate data files for download by interested parties. Web scripts make up the tracking interface, and various tools available on the project web-site (image.llnl.gov) that provide a search interface to the database.

  10. Seductive Details in Multimedia Messages

    ERIC Educational Resources Information Center

    Rey, Gunter Daniel

    2011-01-01

    The seductive detail principle asserts that people learn more deeply from a multimedia presentation when interesting but irrelevant adjuncts are excluded rather than included. However, critics could argue that studies about this principle contain methodological problems. The recent experiment attempts to overcome these problems. Students (N = 108)…

  11. Images.

    ERIC Educational Resources Information Center

    Barr, Catherine, Ed.

    1997-01-01

    The theme of this month's issue is "Images"--from early paintings and statuary to computer-generated design. Resources on the theme include Web sites, CD-ROMs and software, videos, books, and others. A page of reproducible activities is also provided. Features include photojournalism, inspirational Web sites, art history, pop art, and myths. (AEF)

  12. Aircraft empennage structural detail design

    NASA Technical Reports Server (NTRS)

    Meholic, Greg; Brown, Rhonda; Hall, Melissa; Harvey, Robert; Singer, Michael; Tella, Gustavo

    1993-01-01

    This project involved the detailed design of the aft fuselage and empennage structure, vertical stabilizer, rudder, horizontal stabilizer, and elevator for the Triton primary flight trainer. The main design goals under consideration were to illustrate the integration of the control systems devices used in the tail surfaces and their necessary structural supports as well as the elevator trim, navigational lighting system, electrical systems, tail-located ground tie, and fuselage/cabin interface structure. Accommodations for maintenance, lubrication, adjustment, and repairability were devised. Weight, fabrication, and (sub)assembly goals were addressed. All designs were in accordance with the FAR Part 23 stipulations for a normal category aircraft.

  13. Detailed mechanism of benzene oxidation

    NASA Technical Reports Server (NTRS)

    Bittker, David A.

    1987-01-01

    A detailed quantitative mechanism for the oxidation of benzene in both argon and nitrogen diluted systems is presented. Computed ignition delay time for argon diluted mixtures are in satisfactory agreement with experimental results for a wide range of initial conditions. An experimental temperature versus time profile for a nitrogen diluted oxidation was accurately matched and several concentration profiles were matched qualitatively. Application of sensitivity analysis has given approximate rate constant expressions for the two dominant heat release reactions, the oxidation of C6H5 and C5H5 radicals by molecular oxygen.

  14. "Influence Method". Detailed mathematical description

    NASA Astrophysics Data System (ADS)

    Rios, I. J.; Mayer, R. E.

    2015-07-01

    A new method for the absolute determination of nuclear particle flux in the absence of known detector efficiency, the "Influence Method", was recently published (I.J. Rios and R.E. Mayer, Nuclear Instruments & Methods in Physics Research A 775 (2015) 99-104). The method defines an estimator for the population and another estimator for the efficiency. In this article we present a detailed mathematical description which yields the conditions for its application, the probability distributions of the estimators and their characteristic parameters. An analysis of the different cases leads to expressions of the estimators and their uncertainties.

  15. A Generalized Detailed Balance Relation

    NASA Astrophysics Data System (ADS)

    Ruelle, David

    2016-06-01

    Given a system M in a thermal bath we obtain a generalized detailed balance relation for the ratio r=π _τ (K→ J)/π _τ (J→ K) of the transition probabilities M:J→ K and M:K→ J in time τ . We assume an active bath, containing solute molecules in metastable states. These molecules may react with M and the transition J→ K occurs through different channels α involving different reactions with the bath. We find that r=sum p^α r^α , where p^α is the probability that channel α occurs, and r^α depends on the amount of heat (more precisely enthalpy) released to the bath in channel α.

  16. Detailed fuel spray analysis techniques

    NASA Technical Reports Server (NTRS)

    Mularz, E. J.; Bosque, M. A.; Humenik, F. M.

    1983-01-01

    Detailed fuel spray analyses are a necessary input to the analytical modeling of the complex mixing and combustion processes which occur in advanced combustor systems. It is anticipated that by controlling fuel-air reaction conditions, combustor temperatures can be better controlled, leading to improved combustion system durability. Thus, a research program is underway to demonstrate the capability to measure liquid droplet size, velocity, and number density throughout a fuel spray and to utilize this measurement technique in laboratory benchmark experiments. The research activities from two contracts and one grant are described with results to data. The experiment to characterize fuel sprays is also described. These experiments and data should be useful for application to and validation of turbulent flow modeling to improve the design systems of future advanced technology engines.

  17. A Generalized Detailed Balance Relation

    NASA Astrophysics Data System (ADS)

    Ruelle, David

    2016-08-01

    Given a system M in a thermal bath we obtain a generalized detailed balance relation for the ratio r=π _τ (K→ J)/π _τ (J→ K) of the transition probabilities M:J→ K and M:K→ J in time τ . We assume an active bath, containing solute molecules in metastable states. These molecules may react with M and the transition J→ K occurs through different channels α involving different reactions with the bath. We find that r=sum p^α r^α , where p^α is the probability that channel α occurs, and r^α depends on the amount of heat (more precisely enthalpy) released to the bath in channel α.

  18. Morphological details in bloodstain particles.

    PubMed

    De Wael, K; Lepot, L

    2015-01-01

    During the commission of crimes blood can be transferred to the clothing of the offender or on other crime related objects. Bloodstain particles are sub-millimetre sized flakes that are lost from dried bloodstains. The nature of these red particles is easily confirmed using spectroscopic methods. In casework, bloodstain particles showing highly detailed morphological features were observed. These provided a rationale for a series of experiments described in this work. It was found that the "largest" particles are shed from blood deposited on polyester and polyamide woven fabrics. No particles are lost from the stains made on absorbent fabrics and from those made on knitted fabrics. The morphological features observed in bloodstain particles can provide important information on the substrates from which they were lost. PMID:25437904

  19. Optomechanical details in injection-molded assemblies

    NASA Astrophysics Data System (ADS)

    Hebert, Raymond T.

    1995-12-01

    With the advent of low-cost electro-optic components such as LEDs, laser diodes and CCD imaging devices, the cost and performance demands now fall upon the optical subsystems in order to achieve realistic marketing targets for many emerging commercial and consumer products. One of the many benefits of injection-molded plastic optics is the diversity of features that are available to the design team. Once designed and incorporated into the tooling, many features are virtually free in high-volume production. These features can include mechanical details as well as optical functions. Registration features can be included for precisely positioning optical elements to one another or to other assemblies such as printed circuit boards or housings. Snaps, compression features, spring-loading elements, standoffs, self-tapping screws or ultrasonically weldable features can greatly facilitate ease of assembly.

  20. Thirty Meter Telescope Detailed Science Case: 2015

    NASA Astrophysics Data System (ADS)

    Skidmore, Warren; TMT International Science Development Teams; Science Advisory Committee, TMT

    2015-12-01

    The TMT Detailed Science Case describes the transformational science that the Thirty Meter Telescope will enable. Planned to begin science operations in 2024, TMT will open up opportunities for revolutionary discoveries in essentially every field of astronomy, astrophysics and cosmology, seeing much fainter objects much more clearly than existing telescopes. Per this capability, TMT's science agenda fills all of space and time, from nearby comets and asteroids, to exoplanets, to the most distant galaxies, and all the way back to the very first sources of light in the universe. More than 150 astronomers from within the TMT partnership and beyond offered input in compiling the new 2015 Detailed Science Case. The contributing astronomers represent the entire TMT partnership, including the California Institute of Technology (Caltech), the Indian Institute of Astrophysics (IIA), the National Astronomical Observatories of the Chinese Academy of Sciences (NAOC), the National Astronomical Observatory of Japan (NAOJ), the University of California, the Association of Canadian Universities for Research in Astronomy (ACURA) and US associate partner, the Association of Universities for Research in Astronomy (AURA). Cover image: artist's rendition of the TMT International Observatory on Mauna Kea opening in the late evening before beginning operations.

  1. Study of the detail content of Apollo orbital photography

    NASA Technical Reports Server (NTRS)

    Kinzly, R. E.

    1974-01-01

    The development and application of image evaluation methods for assessing the detail content of Apollo orbital photography was demonstrated. Edge analysis using shadow to sunlight edges interior to craters was successfully used to evaluate the fine detail content of Apollo 15, 16, and 17 imagery. A method for evaluating tone quality was developed using a gain factor as a function of object contrast and average exposure level that can be related to object detectability.

  2. The fine details of evolution.

    PubMed

    Laskowski, Roman A; Thornton, Janet M; Sternberg, Michael J E

    2009-08-01

    Charles Darwin's theory of evolution was based on studies of biology at the species level. In the time since his death, studies at the molecular level have confirmed his ideas about the kinship of all life on Earth and have provided a wealth of detail about the evolutionary relationships between different species and a deeper understanding of the finer workings of natural selection. We now have a wealth of data, including the genome sequences of a wide range of organisms, an even larger number of protein sequences, a significant knowledge of the three-dimensional structures of proteins, DNA and other biological molecules, and a huge body of information about the operation of these molecules as systems in the molecular machinery of all living things. This issue of Biochemical Society Transactions contains papers from oral presentations given at a Biochemical Society Focused Meeting to commemorate the 200th Anniversary of Charles Darwin's birth, held on 26-27 January 2009 at the Wellcome Trust Conference Centre, Cambridge. The talks reported on some of the insights into evolution which have been obtained from the study of protein sequences, structures and systems. PMID:19614583

  3. Image tubes

    SciTech Connect

    Csorba, I.P.

    1985-01-01

    This text provides a wealth of valuable, hard-to-find data on electron optics, imaging, and image intensification systems. The author explains details of image tube theory, design, construction, and components. He includes material on the design and operation of camera tubes, power components, and secondary electron emitters, as well as data on photomultiplier tubes and electron guns.

  4. The Finer Details: Climate Modeling

    NASA Technical Reports Server (NTRS)

    2000-01-01

    If you want to know whether you will need sunscreen or an umbrella for tomorrow's picnic, you can simply read the local weather report. However, if you are calculating the impact of gas combustion on global temperatures, or anticipating next year's rainfall levels to set water conservation policy, you must conduct a more comprehensive investigation. Such complex matters require long-range modeling techniques that predict broad trends in climate development rather than day-to-day details. Climate models are built from equations that calculate the progression of weather-related conditions over time. Based on the laws of physics, climate model equations have been developed to predict a number of environmental factors, for example: 1. Amount of solar radiation that hits the Earth. 2. Varying proportions of gases that make up the air. 3. Temperature at the Earth's surface. 4. Circulation of ocean and wind currents. 5. Development of cloud cover. Numerical modeling of the climate can improve our understanding of both the past and, the future. A model can confirm the accuracy of environmental measurements taken. in, the past and can even fill in gaps in those records. In addition, by quantifying the relationship between different aspects of climate, scientists can estimate how a future change in one aspect may alter the rest of the world. For example, could an increase in the temperature of the Pacific Ocean somehow set off a drought on the other side of the world? A computer simulation could lead to an answer for this and other questions. Quantifying the chaotic, nonlinear activities that shape our climate is no easy matter. You cannot run these simulations on your desktop computer and expect results by the time you have finished checking your morning e-mail. Efficient and accurate climate modeling requires powerful computers that can process billions of mathematical calculations in a single second. The NCCS exists to provide this degree of vast computing capability.

  5. Detailed Seismic Reflection Images of the Central American Volcanic Arc

    NASA Astrophysics Data System (ADS)

    McIntosh, K. D.; Fulthorpe, C. S.

    2005-12-01

    New high-resolution seismic reflection profiles across the Central American volcanic arc (CAVA) reveal an asymmetric deformation pattern with large-scale folding and uplift of basinal strata in the forearc contrasted by intrusive bodies, normal faults, and possible strikes-slip faults in the backarc. Since Miocene times the CAVA has migrated seaward, apparently impinging on the Sandino forearc basin and creating or modifying the low-lying Nicaragua depression, which contains the backarc and much of the arc. However the structural nature of the depression and its possible relationship to forearc sliver movement is poorly known. In November-December 2004 we recorded a large, high-resolution, seismic reflection dataset largely on the Pacific shelf (forearc) area of Central America, extending from NW Costa Rica to the SE edge of El Salvador's territorial waters. We seized an opportunity to study the nature of the CAVA by recording data into the Gulf of Fonseca, a large embayment at the intersection of Nicaragua, Honduras, and El Salvador. With 3 GI airguns and a 2100 m streamer we recorded data with typical penetration of 2-3 seconds in the Sandino basin and frequency content of ~10-250 Hz (at shallow levels). Penetration was limited over the arc summit with high velocity volcanic rocks encountered at depths as shallow as a few hundred meters. To the NE the edge of the Nicaragua depression occurs abruptly; our data show a well-developed sedimentary basin 1.5-3 km thick separated by numerous steeply-dipping faults. The broadband signal and good penetration of this dataset will help us determine the chronology of arc development in this position and the styles of deformation in the forearc, arc, and backarc areas. In turn, this will help us understand the regional tectonic and stratigraphic development of this margin due to the profound affects of the arc.

  6. 47. DETAIL OF ORIGINAL VANE ASSEMBLY AND TWO WHEEL SECTIONS ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    47. DETAIL OF ORIGINAL VANE ASSEMBLY AND TWO WHEEL SECTIONS FROM ELI WINDMILLS, THE VANE SHEET BEARING STENCILED PAINTED INSCRIPTION, 'KREGEL WINDMILL CO. ELI NEBRASKA CITY, NEB.' VISIBLE IN THE IMAGE ARE BOTH SIDES OF THE WHEEL SECTIONS, SHOWING THE METHOD OF BLADE MOUNTING FOR ELI WINDMILLS. - Kregel Windmill Company Factory, 1416 Central Avenue, Nebraska City, Otoe County, NE

  7. 22. FROM CREW'S BERTHING, LOOKING TOWARDS STERN, SHOWING DETAIL OF ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    22. FROM CREW'S BERTHING, LOOKING TOWARDS STERN, SHOWING DETAIL OF INTERIOR LICKING MECHANISM OF HATCH DOOR OPENING TO FANTAIL (INTERIOR SIDE OF DOOR IN IMAGE 22). - U.S. Coast Guard Cutter WHITE LUPINE, U.S. Coast Guard Station Rockland, east end of Tillson Avenue, Rockland, Knox County, ME

  8. 7. A DETAIL, TAKEN FROM THE EAST END OF THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    7. A DETAIL, TAKEN FROM THE EAST END OF THE BRIDGE. THIS IMAGE SHOWS THE MODERN, EDGE-LAID 2" X 4" DIMENSIONED LUMBER AS DECKING. - Freedom Bridge, Spanning West Fork of White River at County Road 590 South, Freedom, Owen County, IN

  9. 4. Credit BG. Detail view of pair of Clayton steam ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. Credit BG. Detail view of pair of Clayton steam generators. Left part of image shows front, right part shows back. Generators were removed from 4280/E-81 for shipment to a new owner. - Jet Propulsion Laboratory Edwards Facility, Test Stand D, Steam Generator Plant, Edwards Air Force Base, Boron, Kern County, CA

  10. Detail of north side of Test Stand 'A' base, showing ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail of north side of Test Stand 'A' base, showing tanks for distilled water (left), fuel (center), and gaseous nitrogen (right). Other tanks present for tests were removed before this image was taken. - Jet Propulsion Laboratory Edwards Facility, Test Stand A, Edwards Air Force Base, Boron, Kern County, CA

  11. Hangar no. 2 perspective detail view of west doors. Note ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Hangar no. 2 perspective detail view of west doors. Note door tracks in underside of upper door structure. Darkening at top of image due to lens vignetting. Looking 78 w. - Marine Corps Air Station Tustin, Southern Lighter Than Air Ship Hangar, Near intersection of Windmill Road & Johnson Street, Tustin, Orange County, CA

  12. Software For Drawing Design Details Concurrently

    NASA Technical Reports Server (NTRS)

    Crosby, Dewey C., III

    1990-01-01

    Software system containing five computer-aided-design programs enables more than one designer to work on same part or assembly at same time. Reduces time necessary to produce design by implementing concept of parallel or concurrent detailing, in which all detail drawings documenting three-dimensional model of part or assembly produced simultaneously, rather than sequentially. Keeps various detail drawings consistent with each other and with overall design by distributing changes in each detail to all other affected details.

  13. Fine Details of the Icy Surface of Ganymede

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Dramatic view of fine details in ice hills and valleys in an unnamed region on Jupiter's moon Ganymede. North is to the top of the picture and the sun illuminates the surface from the left. The finest details that can be discerned in this picture are only 11 meters across (similar to the size of an average house) some 2000 times better than previous images of this region. The bright areas in the left hand version are the sides of hills facing the sun; the dark areas are shadows. In the right hand version the processing has been changed to bring out details in the shadowed regions that are illuminated by the bright hillsides. The brightness of some of the hillsides is so high that the picture elements 'spill over' down the columns of the picture. The image was taken on June 28, 1996 from a distance of about 1000 kilometers. The Jet Propulsion Laboratory, Pasadena, CA manages the mission for NASA's Office of Space Science, Washington, DC. This image and other images and data received from Galileo are posted on the World Wide Web, on the Galileo mission home page at URL http://galileo.jpl.nasa.gov. Background information and educational context for the images can be found at URL http://www.jpl.nasa.gov/galileo/sepo

  14. Cornice Detail of Rake, Cornice Detail of Eave, Wood DoubleHung ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Cornice Detail of Rake, Cornice Detail of Eave, Wood Double-Hung Window Details, Wood Door Details - Boxley Grist Mill, Boxley vicinity on State Route 43, Buffalo National River, Ponca, Newton County, AR

  15. Field-based study of volcanic ash via visible and thermal high-speed imaging of explosive eruptions

    NASA Astrophysics Data System (ADS)

    Tournigand, Pierre-Yves; Taddeucci, Jacopo; Scarlato, Piergiorgio; Gaudin, Damien; Del Bello, Elisabetta

    2015-04-01

    Subaerial explosive volcanic activity ejects a mixture of gas-ash-pyroclasts in the atmosphere. Parameterizing the physical processes responsible for ash injection and plume dynamics is crucial to constrain numerical models and forecasts of potentially hazardous ash dispersal events. In this study we present preliminary results from a new method based on visible and thermal high-speed video processing from Strombolian and Vulcanian explosions. High-speed videos were recorded by a Optronis CR600x2 camera (1280x1024 pixels definition, 500 Hz frame rate) for the visible and by a FLIR SC655 (640x480 pixels definition, 50 Hz frame rate) for the thermal. Qualitatively, different dynamics of ash injection and dispersal can be identified. High speed cameras allow us to observe all the different phases during volcanic plume dispersion with a very good time resolution. Multiple features were already observed about volcanic plumes, but this tool give a better accuracy to our observations and allow us to better define previously observed features and to be able to identify new ones. Quantitatively before using our videos a pre-processing is needed which aim is to isolate the plume from the background by using different types of filters without altering the data, to allow us to use automated procedures to track volcanic plumes. In this study we extract data from these videos (plume height, velocity, temperature, mass, volume,...) using different software tools. Doing this allow us to be able to define and constrain main parameters and processes in function of the observed volcano and explosion type, but also to find correlations between parameters and establish empirical relations. We define range of values for each parameter and their respective impact on plume dynamics and stability, to be able to obtain characteristic fields of values for each case and link it to explosions type and evolution.

  16. 5 CFR 532.411 - Details.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Details. 532.411 Section 532.411 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PREVAILING RATE SYSTEMS Pay Administration § 532.411 Details. An appropriated fund employee detailed to a position other than the position...

  17. 49 CFR 176.102 - Supervisory detail.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Supervisory detail. 176.102 Section 176.102... Requirements for Class 1 (Explosive) Materials § 176.102 Supervisory detail. (a) Except as provided in paragraph (c) of this section, the COTP may assign a USCG supervisory detail to any vessel to supervise...

  18. Detailed Globes Enhance Education and Recreation

    NASA Technical Reports Server (NTRS)

    2007-01-01

    Orbis World Globes creates inflatable globes-Earthballs-in many sizes that depict Earth as it is seen from space, complete with atmospheric cloud cover. Orbis designs and produces the most visually authentic replicas of Earth ever created, and NASA took notice of Orbis globes and employed a 16-inch diameter EarthBall for an educational film it made aboard the STS-45 shuttle mission. Orbis later collaborated with NASA to create two 16-foot diameter world globes for display at the 2002 Olympic Winter Games in Salt Lake City, using more detailed satellite imagery. The satellite image now printed on all Orbis globes displays 1-kilometer resolution and is 21,600 by 43,200 pixels in size, and Orbis globes are otherwise meteorologically accurate, though the cloud cover has been slightly reduced in order for most of the landforms to be visible. Orbis also developed the exclusive NightGlow Cities feature, enabling EarthBalls to display the world's cities as they appear as the Earth revolves from daylight into night. Orbis inflatable globes are available in sizes from 1 to 100 feet in diameter, with the most common being the standard 16-inch and 1-meter diameter EarthBalls. Applications include educational uses from preschools to universities, games, and for a variety of display purposes at conferences, trade shows, festivals, concerts, and parades. A 16-foot diameter Orbis globe was exhibited at the United Nations' World Urban Forum, in Vancouver, Canada; the Space 2006 conference, in San Jose, California; and the X-Prize Cup Personal Spaceflight Exposition in Las Cruces, New Mexico.

  19. Detail view of the interior of the flight deck looking ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail view of the interior of the flight deck looking forward showing the overhead control panels. Note that the flight deck windows have protective covers over them in this view. This images can be digitally stitched with image HAER No. TX-116-A-19 to expand the view to include the Commander and Pilot positions during ascent and reentry and landing. This view was taken in the Orbiter Processing Facility at the Kennedy Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

  20. Expanded applications for high performance VOx microbolometer FPAs

    NASA Astrophysics Data System (ADS)

    Murphy, D.; Ray, M.; Kennedy, A.; Wyles, J.; Hewitt, C.; Wyles, R.; Gordon, E.; Sessler, T.; Baur, S.; Van Lue, D.; Anderson, S.; Chin, R.; Gonzalez, H.; Le Pere, C.; Ton, S.; Kostrzewa, T.

    2005-05-01

    RVS is producing high-quality microbolometer FPAs with 25 μm pixels. We have developed formats in both 320 x 240 and 640 x 480 array formats. These FPAs have demonstrated sensitivities that are comparable to microbolometer FPAs with 50 μm pixels with the best measured NETD value for these FPAs now <25mK with an f/1 aperture and operating at 30 Hz frame rates. Pixel operability is greater than 99.9% on most FPAs, and uncorrected responsivity nonuniformity is less than 3% (sigma/mean). These 25 μm microbolometer detectors also have a relatively fast thermal time constant of approximately 10 msec. These arrays have produced excellent image quality, and are currently fielded in a variety of systems. We will report on our latest performance data and IR captive flight test imagery. We will also show data on 25μm arrays that have been designed for faster time constants (5 msec), while maintaining high performance. RVS is also developing a 320 x 240 50μm mid-wave responding FPA. We will review the MWIR sensitivity improvements with this array and provide IR imagery. RVS is developing a 640 x 480 25μm uncooled FPA for a countermine detection application using a two-band assembly designed to be sensitive in both the Restrahlen and Thermal spectral bands. We will provide IR image data on these arrays. RVS has made a significant breakthrough in the development of a 640 x 512 array with a unit cell size of 20 μm x 20 μm, and performance approaching that of the 25μm arrays. The successful development of this array is the first step in achieving mega-pixel formats. This FPA is designed to ultimately achieve performance near the temperature fluxuation limited NETD (<20mK, f/1, 30 Hz). We will show updated performance and imagery on these arrays, which is currently being measured at <45mK, f/1, 30 Hz.

  1. Resolution and sensitivity improvements for VOx microbolometer FPAs

    NASA Astrophysics Data System (ADS)

    Murphy, Daniel F.; Kennedy, Adam; Ray, Michael; Wyles, Richard; Wyles, Jessica; Asbrock, James F.; Hewitt, C.; Van Lue, David; Sessler, T.; Anderson, John S.; Bradley, Daryl; Chin, Richard; Gonzales, H.; Le Pere, C.; Kostrzewa, Thomas

    2003-09-01

    Raytheon Vision Systems (RVS) has achieved a significant technical breakthrough in uncooled FPAs by reducing the pixel size by a factor of two while maintaining state-of-the-art sensitivity. Raytheon is producing high-quality 320 x 240 microbolometer FPAs with 25 μm pitch pixels. The 320 x 240 FPAs have a sensitivity that is comparable to microbolometer FPAs with 50 μm pixels. The array average NETD value for these FPAs is about 30 mK with an f/1 aperture and operating at 30 Hz frame rates. Pixel operability is greater than 99% on most FPAs, and uncorrected responsivity nonuniformity is less than 4% (sigma/mean). These 25 μm microbolometer detectors also have a relatively fast thermal time constant of approximately 10 msec. This state-of-the-art performance has been achieved as a result of an advanced micro machining fabrication process, which allows maximization of both the thermal isolation and the optical fill-factor. These arrays have produced excellent image quality, and are currently fielded in demonstration systems. The reduction in pixel size offers several potential benefits for IR systems. For a given system resolution (IFOV) requirement, the 25 μm pxiels allow a factor of two reduction in both the focal length and aperture size of the sensor optics. These FPAs are applicable to wide-field-of-view, long-range surveillance and targeting missions. The pixel size reduction facilitates a significant FPA cost reduction since the number of die printed on a wafer can be increased, and also has enabled the development of a large-format 640 x 480 FPA array. Raytheon is producing these arrays with very good sensitivity. These arrays have excellent operability and image quality. Several dual FOV prototype systems have been delivered under the LCMS and UAV programs, and are under evaluation at NVESD. Raytheon Vision Systems (RVS) has developed a flexible uncooled front end (UFE) electronics that will serve as the basis for camera engine systems using 320 x 240

  2. 17. A closeup detail, looking east from the northeast corner ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    17. A close-up detail, looking east from the northeast corner of the roadbed. This image shows the concrete commemorative inscription which is let into the inside of the eastern balustrade at the north end of the bridge. The name of one of the county commissioners has been chiselled out of the inscription. The parting fault between the parapet and its coping is evident. - Vigo County Bridge No. 139, Spanning Sugar Creek at Seventy-fourth Place, Terre Haute, Vigo County, IN

  3. Detail view of the port side of the payload bay ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail view of the port side of the payload bay of the Orbiter Discovery. This view shows Remote Manipulator System, Canadarm, sensors in the center of the image and a close-up view of a small segment of the orbiter's radiator panel. This photograph was taken in the Orbiter Processing Facility at the Kennedy Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

  4. Detail view of the underside of a elevon on the ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail view of the underside of a elevon on the port side wing of the Orbiter Discovery. Note the wear and replacement patterns of the High-temperature Reusable Surface Insulation tiles. This image was taken inside of the Orbiter Processing Facility at Kennedy Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

  5. Clinical professional governance for detailed clinical models.

    PubMed

    Goossen, William; Goossen-Baremans, Anneke

    2013-01-01

    This chapter describes the need for Detailed Clinical Models for contemporary Electronic Health Systems, data exchange and data reuse. It starts with an explanation of the components related to Detailed Clinical Models with a brief summary of knowledge representation, including terminologies representing clinic relevant "things" in the real world, and information models that abstract these in order to let computers process data about these things. Next, Detailed Clinical Models are defined and their purpose is described. It builds on existing developments around the world and accumulates in current work to create a technical specification at the level of the International Standards Organization. The core components of properly expressed Detailed Clinical Models are illustrated, including clinical knowledge and context, data element specification, code bindings to terminologies and meta-information about authors, versioning among others. Detailed Clinical Models to date are heavily based on user requirements and specify the conceptual and logical levels of modelling. It is not precise enough for specific implementations, which requires an additional step. However, this allows Detailed Clinical Models to serve as specifications for many different kinds of implementations. Examples of Detailed Clinical Models are presented both in text and in Unified Modelling Language. Detailed Clinical Models can be positioned in health information architectures, where they serve at the most detailed granular level. The chapter ends with examples of projects that create and deploy Detailed Clinical Models. All have in common that they can often reuse materials from earlier projects, and that strict governance of these models is essential to use them safely in health care information and communication technology. Clinical validation is one point of such governance, and model testing another. The Plan Do Check Act cycle can be applied for governance of Detailed Clinical Models

  6. Imaging Biomarkers or Biomarker Imaging?

    PubMed Central

    Mitterhauser, Markus; Wadsak, Wolfgang

    2014-01-01

    Since biomarker imaging is traditionally understood as imaging of molecular probes, we highly recommend to avoid any confusion with the previously defined term “imaging biomarkers” and, therefore, only use “molecular probe imaging (MPI)” in that context. Molecular probes (MPs) comprise all kinds of molecules administered to an organism which inherently carry a signalling moiety. This review highlights the basic concepts and differences of molecular probe imaging using specific biomarkers. In particular, PET radiopharmaceuticals are discussed in more detail. Specific radiochemical and radiopharmacological aspects as well as some legal issues are presented. PMID:24967536

  7. 18 CFR 401.122 - Supplementary details.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Supplementary details. 401.122 Section 401.122 Conservation of Power and Water Resources DELAWARE RIVER BASIN COMMISSION ADMINISTRATIVE MANUAL RULES OF PRACTICE AND PROCEDURE General Provisions § 401.122 Supplementary details....

  8. 24. 'HANGAR SHEDS ELEVATIONS DETAILS; ARCHITECTURAL PLANS ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    24. 'HANGAR SHEDS - ELEVATIONS - DETAILS; ARCHITECTURAL PLANS - PLANT AREA; MODIFICATION CENTER NO. 1, DAGGETT, CALIFORNIA.' Partial elevations, and details of sliding doors and ventilator flaps, as built. Contract no. W509 Eng. 2743; File no. 555/81, revision B, dated April 6, 1943. No sheet number. - Barstow-Daggett Airport, Hangar Shed No. 4, 39500 National Trails Highway, Daggett, San Bernardino County, CA

  9. 5 CFR 317.903 - Details.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ..., detail means the temporary assignment of an SES member to another position (within or outside of the SES) or the temporary assignment of a non-SES member to an SES position, with the expectation that the... agency may not detail an SES employee to unclassified duties for more than 240 days. (3) An agency...

  10. Graphics hardware accelerated panorama builder for mobile phones

    NASA Astrophysics Data System (ADS)

    Bordallo López, Miguel; Hannuksela, Jari; Silvén, Olli; Vehviläinen, Markku

    2009-02-01

    Modern mobile communication devices frequently contain built-in cameras allowing users to capture highresolution still images, but at the same time the imaging applications are facing both usability and throughput bottlenecks. The difficulties in taking ad hoc pictures of printed paper documents with multi-megapixel cellular phone cameras on a common business use case, illustrate these problems for anyone. The result can be examined only after several seconds, and is often blurry, so a new picture is needed, although the view-finder image had looked good. The process can be a frustrating one with waits and the user not being able to predict the quality beforehand. The problems can be traced to the processor speed and camera resolution mismatch, and application interactivity demands. In this context we analyze building mosaic images of printed documents from frames selected from VGA resolution (640x480 pixel) video. High interactivity is achieved by providing real-time feedback on the quality, while simultaneously guiding the user actions. The graphics processing unit of the mobile device can be used to speed up the reconstruction computations. To demonstrate the viability of the concept, we present an interactive document scanning application implemented on a Nokia N95 mobile phone.

  11. Real-time color/shape-based traffic signs acquisition and recognition system

    NASA Astrophysics Data System (ADS)

    Saponara, Sergio

    2013-02-01

    A real-time system is proposed to acquire from an automotive fish-eye CMOS camera the traffic signs, and provide their automatic recognition on the vehicle network. Differently from the state-of-the-art, in this work color-detection is addressed exploiting the HSI color space which is robust to lighting changes. Hence the first stage of the processing system implements fish-eye correction and RGB to HSI transformation. After color-based detection a noise deletion step is implemented and then, for the classification, a template-based correlation method is adopted to identify potential traffic signs, of different shapes, from acquired images. Starting from a segmented-image a matching with templates of the searched signs is carried out using a distance transform. These templates are organized hierarchically to reduce the number of operations and hence easing real-time processing for several types of traffic signs. Finally, for the recognition of the specific traffic sign, a technique based on extraction of signs characteristics and thresholding is adopted. Implemented on DSP platform the system recognizes traffic signs in less than 150 ms at a distance of about 15 meters from 640x480-pixel acquired images. Tests carried out with hundreds of images show a detection and recognition rate of about 93%.

  12. Evaluate depth of field limits of fixed focus lens arrangements in thermal infrared

    NASA Astrophysics Data System (ADS)

    Schuster, Norbert

    2016-05-01

    More and more modern thermal imaging systems use uncooled detectors. High volume applications work with detectors that have a reduced pixel count (typically between 200x150 and 640x480). This reduces the usefulness of modern image treatment procedures such as wave front coding. On the other hand, uncooled detectors demand lenses with fast fnumbers, near f/1.0, which reduces the expected Depth of Field (DoF). What are the limits on resolution if the target changes distance to the camera system? The desire to implement lens arrangements without a focusing mechanism demands a deeper quantification of the DoF problem. A new approach avoids the classic "accepted image blur circle" and quantifies the expected DoF by the Through Focus MTF of the lens. This function is defined for a certain spatial frequency that provides a straightforward relation to the pixel pitch of imaging device. A certain minimum MTF-level is necessary so that the complete thermal imaging system can realize its basic functions, such as recognition or detection of specified targets. Very often, this technical tradeoff is approved with a certain lens. But what is the impact of changing the lens for one with a different focal length? Narrow field lenses, which give more details of targets in longer distances, tighten the DoF problem. A first orientation is given by the hyperfocal distance. It depends in a square relation on the focal length and in a linear relation on the through focus MTF of the lens. The analysis of these relations shows the contradicting requirements between higher thermal and spatial resolution, faster f-number and desired DoF. Furthermore, the hyperfocal distance defines the DoF-borders. Their relation between is such as the first order imaging formulas. A calculation methodology will be presented to transfer DoF-results from an approved combination lens and camera to another lens in combination with the initial camera. Necessary input for this prediction is the accepted DoF of

  13. 25. 'HANGAR SHEDS TRUSSES DETAILS; ARCHITECTURAL PLANS ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    25. 'HANGAR SHEDS - TRUSSES - DETAILS; ARCHITECTURAL PLANS - PLANT AREA; MODIFICATION CENTER NO. 1, DAGGETT, CALIFORNIA.' Sections and details of trusses, ironwork, and joints, as modified to show ridge joint detail. As built. This blueline also shows the fire suppression system, added in orange pencil for 'Project 13: Bldgs. T-30, T-50, T-70, T-90' at a later, unspecified date. Contract no. W509 Eng. 2743; File no. 555/84, revision B, dated August 24, 1942. No sheet number. - Barstow-Daggett Airport, Hangar Shed No. 4, 39500 National Trails Highway, Daggett, San Bernardino County, CA

  14. POSITIVE EMOTIONS ENHANCE RECALL OF PERIPHERAL DETAILS

    PubMed Central

    Talarico, Jennifer M.; Berntsen, Dorthe; Rubin, David C.

    2011-01-01

    Emotional arousal and negative affect enhance recall of central aspects of an event. However, the role of discrete emotions in selective memory processing is understudied. Undergraduates were asked to recall and rate autobiographical memories of eight emotional events. Details of each memory were rated as central or peripheral to the event. Significance of the event, vividness, reliving and other aspects of remembering were also rated for each event. Positive affect enhanced recall of peripheral details. Furthermore, the impairment of peripheral recall was greatest in memories of anger, not of fear. Reliving the experience at retrieval was negatively correlated with recall of peripheral details for some emotions (e.g., anger) but not others (e.g., fear), irrespective of similarities in affect and intensity. Within individuals, recall of peripheral details was correlated with less belief in the memory’s accuracy and more likelihood to recall the memory from one’s own eyes (i.e., a field perspective). PMID:21359127

  15. Global detailed geoid computation and model analysis

    NASA Technical Reports Server (NTRS)

    Marsh, J. G.; Vincent, S.

    1974-01-01

    Comparisons and analyses were carried out through the use of detailed gravimetric geoids which we have computed by combining models with a set of 26,000 1 deg x 1 deg mean free air gravity anomalies. The accuracy of the detailed gravimetric geoid computed using the most recent Goddard earth model (GEM-6) in conjunction with the set of 1 deg x 1 deg mean free air gravity anomalies is assessed at + or - 2 meters on the continents of North America, Europe, and Australia, 2 to 5 meters in the Northeast Pacific and North Atlantic areas, and 5 to 10 meters in other areas where surface gravity data are sparse. The R.M.S. differences between this detailed geoid and the detailed geoids computed using the other satellite gravity fields in conjuction with same set of surface data range from 3 to 7 meters.

  16. Principle of Detailed Balance in Kinetics

    ERIC Educational Resources Information Center

    Alberty, Robert A.

    2004-01-01

    The effects of the detailed balance on chemical kinetics on the chemical monomolecular triangle reactions are illustrated. A simple experiment that illustrates oscillations, limit cycles, bifurcations and noise are illustrated along with the oscillating reactions.

  17. Experimental study of an uncooled microbolometer array for thermal mapping and spectroscopy of asteroids

    NASA Astrophysics Data System (ADS)

    Brageot, E.; Groussin, O.; Lamy, P.; Reynaud, J.-L.

    2014-12-01

    We report on the experimental study of the imaging and spectroscopic capabilities of an uncooled microbolometer array for space missions to small bodies in the inner solar system. The selected Nano640E T M device manufactured by the ULIS company (Grenoble, France) has a format of 640x480 pixels and can measure temperatures down to at least 255 K, the lower limit reached in our tests. It has a Noise Equivalent Temperature Difference (NETD) of 40.9 ±4.5 mK (300 K, F/0.86) and the capability to produce excellent, radiometrically calibrated images with an error of the order of 1 to 5 K depending upon the number of calibration sources. Using a set of neutral density filters, we determined the signal-to-noise ratio (SNR) of a spectrum acquired by the detector, as a function of the scene temperature, wavelength and spectral resolution. Considering an asteroid at 1 AU from the Sun, an optical system at F/0.86, a spectral resolution of 0.3 μm and a scene temperature of >350 K, the resulting spectrum has sufficient SNR to properly identify the main mineralogical emission features. Our results show that uncooled microbolometer arrays are very promising to acquire calibrated thermal images and mid-infrared (8-14 μm) spectra of the surface of small bodies in the inner solar system.

  18. Developments in uncooled IR technology at BAE SYSTEMS

    NASA Astrophysics Data System (ADS)

    Gurnee, Mark N.; Kohin, Margaret; Blackwell, Richard J.; Butler, Neal R.; Whitwam, Jason T.; Backer, Brian S.; Leary, Arthur R.; Nielson, Thomas

    2001-10-01

    Uncooled microbolometer thermal imaging sensor technology has begun to successfully address military, government and commercial applications in the real world. BAE SYSTEMS, located in Lexington MA, has been involved in the design and development of uncooled IR technology since the early 1980s. Our current MicroIRTM products are based on vanadium oxide (VOx) microbolometers. Thousands of uncooled microbolometer thermal imaging sensors are now being produced and sold annually. A the same time, applied research and development on the technology continues to improve the basic products and make them suitable for new applications. In this paper we report on the status and improvements achieved in the MicroIRTM product line, based on 320 X 240 element and 160 X 120 element FPA's with 46 μm pixel pitch. Other near term MicroIRTM products include 320 X 240 and 640 X 480 FPA's with 28 micrometers pixel pitch and measured sensitivities below 50 mK. In the systems area we discuss development and testing of a Light Thermal Weapon Sight (LTWS) for the U.S. Army, being developed by BAE SYSTEMS in partnership with Thales, based upon our uncooled MicroIRTM focal plane arrays (FPA) and systems. The LTWS prototypes were based upon our Standard Imaging Module SIM200, which employs our LAM2C, 320 X 240 element, microbolometer FPA. Finally we discuss the 480 X 640 element FPA and its application to the Heavy Thermal Weapon Sight application.

  19. Particle displacement tracking applied to air flows

    NASA Technical Reports Server (NTRS)

    Wernet, Mark P.

    1991-01-01

    Electronic Particle Image Velocimeter (PIV) techniques offer many advantages over conventional photographic PIV methods such as fast turn around times and simplified data reduction. A new all electronic PIV technique was developed which can measure high speed gas velocities. The Particle Displacement Tracking (PDT) technique employs a single cw laser, small seed particles (1 micron), and a single intensified, gated CCD array frame camera to provide a simple and fast method of obtaining two-dimensional velocity vector maps with unambiguous direction determination. Use of a single CCD camera eliminates registration difficulties encountered when multiple cameras are used to obtain velocity magnitude and direction information. An 80386 PC equipped with a large memory buffer frame-grabber board provides all of the data acquisition and data reduction operations. No array processors of other numerical processing hardware are required. Full video resolution (640x480 pixel) is maintained in the acquired images, providing high resolution video frames of the recorded particle images. The time between data acquisition to display of the velocity vector map is less than 40 sec. The new electronic PDT technique is demonstrated on an air nozzle flow with velocities less than 150 m/s.

  20. Interior building details of Building C, Room C203: detail decorative ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Interior building details of Building C, Room C-203: detail decorative radiator and four-over-four windows; southwesterly view - San Quentin State Prison, Building 22, Point San Quentin, San Quentin, Marin County, CA

  1. Making detailed predictions makes (some) predictions worse

    NASA Astrophysics Data System (ADS)

    Kelly, Theresa F.

    In this paper, we investigate whether making detailed predictions about an event makes other predictions worse. Across 19 experiments, 10,895 participants, and 415,960 predictions about 724 professional sports games, we find that people who made detailed predictions about sporting events (e.g., how many hits each baseball team would get) made worse predictions about more general outcomes (e.g., which team would win). We rule out that this effect is caused by inattention or fatigue, thinking too hard, or a differential reliance on holistic information about the teams. Instead, we find that thinking about game-relevant details before predicting winning teams causes people to give less weight to predictive information, presumably because predicting details makes information that is relatively useless for predicting the winning team more readily accessible in memory and therefore incorporated into forecasts. Furthermore, we show that this differential use of information can be used to predict what kinds of games will and will not be susceptible to the negative effect of making detailed predictions.

  2. Three-dimensional shape construction of pulsatile tissue from ultrasonic movies for assistance of clinical diagnosis

    NASA Astrophysics Data System (ADS)

    Fukuzawa, Masayuki; Kawaguchi, Hikari; Yamada, Masayoshi; Nakamori, Nobuyuki; Kitsunezuka, Yoshiki

    2010-02-01

    Three-dimensional shape of pulsatile tissue due to blood flow, which is one of key diagnostic features in ischemia, has been constructed from 2D ultrasonic movies for assisting clinical diagnosis. The 2D ultrasonic movies (640x480pixels/frame, 8bits/pixel, 33ms/frame) were taken with a conventional ultrasonic apparatus and an ultrasonic probe, while measuring the probe orientations with a compact tilt-sensor. The 2D images of pulsatile strength were obtained from each 2D ultrasonic movie by evaluating a heartbeat-frequency component calculated by Fourier transform of a series of pixel values sampled at each pixel. The 2D pulsatile images were projected into a 3D domain to obtain a 3D grid of pulsatile strength according to the probe orientations. The 3D shape of pulsatile tissue was constructed by determining the iso-surfaces of appropriate strength in the 3D grid. The shapes of pulsatile tissue examined in neonatal crania clearly represented the 3D structures of several arteries such as middle cerebral artery, which is useful for diagnosis of ischemic diseases. Since our technique is based on feature extraction in tissue dynamics, it is also useful for homogeneous tissue, for which conventional 3D ultrasonogram is unsuitable due to unclear tissue boundary.

  3. An obstacle detection system using binocular stereo fisheye lenses for planetary rover navigation

    NASA Astrophysics Data System (ADS)

    Liu, L.; Jia, J.; Li, L.

    In this paper we present an implementation of an obstacle detection system using binocular stereo fisheye lenses for planetary rover navigation The fisheye lenses can improve image acquisition efficiency and handle minimal clearance recovery problem because they provide a large field of view However the fisheye lens introduces significant distortion in the image and this will make it much more difficult to find a one-to-one correspondence In addition we have to improve the system accuracy and efficiency for robot navigation To compute dense depth maps accurately in real time the following five key issues are considered 1 using lookup tables for a tradeoff between time and space in fisheye distortion correction and correspondence matching 2 using an improved incremental calculation scheme for algorithmic optimization 3 multimedia instruction set MMX implementation 4 consistency check to remove wrong stereo matching problems suffering from occlusions or mismatches 5 constraints of the recovery space To realize obstacle detection robustly we use the following three steps 1 extracting the ground plane parameters using Randomized Hough Transform 2 filtering the ground and background 3 locating the obstacles by using connected region detection Experimental results show the system can run at 3 2fps in 2 0GHz PC with 640X480 pixels

  4. Further advances in autostereoscopic technology at Dimension Technologies Inc.

    NASA Astrophysics Data System (ADS)

    Eichenlaub, Jesse B.

    1992-06-01

    Dimension Technologies is currently one of three companies offering autostereoscopic displays for sale and one of several which are actively pursuing advances to the technology. We have devised a new autostereoscopic imaging technique which possesses several advantages over previously explored methods. We are currently manufacturing autostereoscopic displays based on this technology, as well as vigorously pursuing research and development toward more advanced displays. During the past year, DTI has made major strides in advancing its LCD based autostereoscopic display technology. DTI has developed a color product -- a stand alone 640 X 480 flat panel LCD based 3-D display capable of accepting input from IBM PC and Apple MAC computers or TV cameras, and capable of changing from 3-D mode to 2-D mode with the flip of a switch. DTI is working on development of a prototype second generation color product that will provide autostereoscopic 3-D while allowing each eye to see the full resolution of the liquid crystal display. And development is also underway on a proof-of-concept display which produces hologram-like look-around images visible from a wide viewing angle, again while allowing the observer to see the full resolution of the display from all locations. Development of a high resolution prototype display of this type has begun.

  5. Low-SWaP shutterless uncooled video core by SCD

    NASA Astrophysics Data System (ADS)

    Mizrahi, U.; Yuval, S.; Hirsh, Y.; Sinai, Y.; Lury, Y.; Gridish, Y.; Syrel, N.; Shamay, Y.; Meshorer, R.; Iosevich, R.; Horesh, S. L.

    2015-06-01

    Over the last decade SCD has established a "state of the art" VOx μ-Bolometer product line. The market demands for low SWaP (Size, Weight and Power) uncooled engines is steadily growing, where low SWaP is especially critical in battery-operated applications such as goggles and Thermal Weapon Sights (TWS). In this approach, SCD has developed a low-SWaP, shutter-less uncooled video core, with a foot-print of 31x31mm and sub Watt power consumption. The video core contains a temperature calibrated, High Sensitivity (HS) 640x480 17μm pitch detector (NETD <= 32mK @ 30Hz, F/1), packaged in a new TEC-less ceramic package (26x23mm). The video core contains superior image processing algorithms including: local and global Dynamic Range Compression (DRC), and spatial and temporal de-noising algorithms providing low NETD and stable and low Residual Non Uniformity (RNU) video image.

  6. 4. TROJAN MILL, DETAIL OF CRUDE ORE BINS FROM NORTH, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. TROJAN MILL, DETAIL OF CRUDE ORE BINS FROM NORTH, c. 1912. SHOWS TIMBER FRAMING UNDER CONSTRUCTION FOR EAST AND WEST CRUDE ORE BINS AT PREVIOUS LOCATION OF CRUSHER HOUSE, AND SNOW SHED PRESENT OVER SOUTH CRUDE ORE BIN WITH PHASE CHANGE IN SNOW SHED CONSTRUCTION INDICATED AT EAST END OF EAST CRUDE ORE BIN. THIS PHOTOGRAPH IS THE FIRST IMAGE OF THE MACHINE SHOP, UPPER LEFT CORNER. CREDIT JW. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

  7. Detail in architecture: Between arts & crafts

    NASA Astrophysics Data System (ADS)

    Dulencin, Juraj

    2016-06-01

    Architectural detail represents an important part of architecture. Not only can it be used as an identifier of a specific building but at the same time enhances the experience of the realized project. Within it lie the signs of a great architect and clues to understanding his or her way of thinking. It is therefore the central topic of a seminar offered to architecture students at the Brno University of Technology. During the course of the semester-long class the students acquaint themselves with atypical architectural details of domestic and international architects by learning to read them, understand them and subsequently draw them by creating architectural blueprints. In other words, by general analysis of a detail the students learn theoretical thinking of its architect who, depending on the nature of the design, had to incorporate a variety of techniques and crafts. Students apply this analytical part to their own architectural detail design. The methodology of the seminar consists of experiential learning by project management and is complemented by a series of lectures discussing a diversity of details as well as materials and technologies required to implement it. The architectural detail design is also part of students' bachelors thesis, therefore, the realistic nature of their blueprints can be verified in the production process of its physical counterpart. Based on their own documentation the students choose the most suitable manufacturing process whether it is supplied by a specific technology or a craftsman. Students actively participate in the production and correct their design proposals in real scale with the actual material. A student, as a future architect, stands somewhere between a client and an artisan, materializes his or her idea and adjusts the manufacturing process so that the final detail fulfills aesthetic consistency and is in harmony with its initial concept. One of the very important aspects of the design is its economic cost, an

  8. Details Of Collision-Avoidance Study

    NASA Technical Reports Server (NTRS)

    Chappell, Sheryl L.; Billings, Charles E.; Olsen, M. Christine; Scott, Barry C.; Tuttell, Robert J.; Kozon, Thomas E.

    1990-01-01

    Report provides background information on and detailed description of study of pilots' use of traffic-alert and collision-avoidance system (TCAS II) in simulated flights. Described in article, "Evaluation of an Aircraft-Collision-Avoidance System" (ARC-12367). Plans, forms, training narratives, scripts, questionnaires, and other information compiled.

  9. Occupation Competency Profile: Steel Detailer Program.

    ERIC Educational Resources Information Center

    Alberta Learning, Edmonton. Apprenticeship and Industry Training.

    This document presents information about the apprenticeship training program of Alberta, Canada, in general and the steel detailer program in particular. The first part of the document discusses the following items: Alberta's apprenticeship and industry training system; the apprenticeship and industry training committee structure; local…

  10. Details on the biography of Jerzy Neyman

    NASA Astrophysics Data System (ADS)

    Gaina, Alex

    2003-04-01

    Details on the biography of Jerzy Neyman (1894-1981) and a short outline of the native town Tighina in Basarabia (the Republic of Moldova) of the outstanding mathematician and statistician, astronomer, meteorologist, biologist, philosopher and sociologist, founder of the mathematical theory of selection has been given.

  11. 33 CFR 116.20 - Detailed investigation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., Bridge Administration Program determines that a Detailed Investigation should be conducted, the District Commander will initiate an investigation that addresses all of the pertinent data regarding the bridge... will discuss: the obstructive character of the bridge in question; the impact of that bridge...

  12. States Anxious to Get Details about Stimulus

    ERIC Educational Resources Information Center

    Hoff, David J.

    2009-01-01

    As Congress began debate last week over the size and scope of more than $120 billion in proposed emergency education aid, state leaders were anxiously awaiting the details so they could make specific plans to spend the economic-stimulus money. Governors, state legislators, and state schools chiefs have yet to learn what rules Congress will attach…

  13. Big Heads, Small Details and Autism

    ERIC Educational Resources Information Center

    White, Sarah; O'Reilly, Helen; Frith, Uta

    2009-01-01

    Autism is thought to be associated with a bias towards detail-focussed processing. While the cognitive basis remains controversial, one strong hypothesis is that there are high processing costs associated with changing from local into global processing. A possible neural mechanism underlying this processing style is abnormal neural connectivity;…

  14. Mars Polar Lander Site Surface Details

    NASA Technical Reports Server (NTRS)

    1999-01-01

    This picture is an enlargement of a portion of a MOC image taken in late July 1999, showing the onset of defrosting of the seasonal carbon dioxide frost cap (small, occasionally fan-shaped dark spots seen throughout this image). Two craters are seen in this image, a very rare occurrence on the south polar layered deposits. Shown for comparison at the same scale is a picture of Jack Murphy (now Qualcomm) Stadium in San Diego, California. Clearly visible in the inset is the baseball diamond and pitcher's mound; less clear but certainly visible are a number of automobiles (small light dots) in the parking lot west (to the left) of the stadium. The elevation of the sun in the Mars image is about 10o; the sunlight is coming from the bottom (north) in this image. The shadow of the rims of the craters can be used to determine their depths. The smaller crater in the bottom right corner is about 60 m (197 feet) across and 7 m (23 feet) deep; the large crater just below the inset is 175 m (574 feet) across and 17 m (56 feet) deep. Similar calculations for other features in the images indicate that much of the surface is smooth and flat. Relief is typically much less than 1-2 meters (3-7 feet) in height over areas of 10-15 meters across (33-49 feet).

    Malin Space Science Systems and the California Institute of Technology built the MOC using spare hardware from the Mars Observer mission. MSSS operates the camera from its facilities in San Diego, CA. The Jet Propulsion Laboratory's Mars Surveyor Operations Project operates the Mars Global Surveyor spacecraft with its industrial partner, Lockheed Martin Astronautics, from facilities in Pasadena, CA and Denver, CO.

  15. Large format VOx microbolometer UFPA development at ITC

    NASA Astrophysics Data System (ADS)

    Hay, Kenneth A.

    2006-08-01

    L-3 Communications InfraredVision Technology Corporation (ITC) has developed a high performance (25μm) 640x480 microbolometer Uncooled Focal Plane Array (UFPA). ITC offers this high-performance VO x microbolometer-based detector (ITC-2000) to camera manufacturers requiring a state-of-the-art uncooled infrared detector. The ITC-2000 has ten bits of on-chip NonUniformity Correction (NUC) to extend both dynamic range and sensitivity. A serial interface allows programmable gain and global offset to tailor output to the application. The sensor is capable of frame rates up to 30 Hz, non-interlaced. The output is differential to reject common-mode noise. Two temperature sensors are available on chip for monitoring temperature drift. A thermal electric stabilizer is provided in the detector package, if the camera manufacturer requires temperature stabilization. The lightweight package provides a mounting bracket capable of precision alignment to the focal plane array. The addition of the ITC-2000 large-format detector complements ITC's existing ITC-1000 series detector module that addresses both imaging and radiometric commercial-camera applications.

  16. Advancement in 17-micron pixel pitch uncooled focal plane arrays

    NASA Astrophysics Data System (ADS)

    Li, Chuan; Skidmore, George; Howard, Christopher; Clarke, Elwood; Han, C. J.

    2009-05-01

    This paper provides an update of 17 micron pixel pitch uncooled microbolometer development at DRS. Since the introduction of 17 micron pitch 640x480 focal plane arrays (FPAs) in 2006, significant progress has been made in sensor performance and manufacturing processes. The FPAs are now in initial production with an FPA noise equivalent temperature difference (NETD), detector thermal time constant, and pixel operability equivalent or better than that of the current 25 micron pixel pitch production FPAs. NETD improvement was achieved without compromising detector thermal response or thermal time constant by simultaneous reduction in bolometer heat capacity and thermal conductance. In addition, the DRS unique "umbrella" microbolometer cavities were optically tuned to optimize detector radiation absorption for specific spectral band applications. The 17 micron pixel pitch FPAs are currently being considered for the next generation soldier systems such as thermal weapon sights (TWS), vehicle driver vision enhancers (DVE), digitally fused enhanced night vision goggles (DENVG) and unmanned air vehicle (UAV) surveillance sensors, because of overall thermal imaging system size, weight and power advantages.

  17. High-resolution real-time 3D shape measurement on a portable device

    NASA Astrophysics Data System (ADS)

    Karpinsky, Nikolaus; Hoke, Morgan; Chen, Vincent; Zhang, Song

    2013-09-01

    Recent advances in technology have enabled the acquisition of high-resolution 3D models in real-time though the use of structured light scanning techniques. While these advances are impressive, they require large amounts of computing power, thus being limited to using large desktop computers with high end CPUs and sometimes GPUs. This is undesirable in making high-resolution real-time 3D scanners ubiquitous in our mobile lives. To address this issue, this work describes and demonstrates a real-time 3D scanning system that is realized on a mobile device, namely a laptop computer, which can achieve speeds of 20fps 3D at a resolution of 640x480 per frame. By utilizing a graphics processing unit (GPU) as a multipurpose parallel processor, along with a parallel phase shifting technique, we are able to realize the entire 3D processing pipeline in parallel. To mitigate high speed camera transfer problems, which typically require a dedicated frame grabber, we make use of USB 3.0 along with direct memory access (DMA) to transfer camera images to the GPU. To demonstrate the effectiveness of the technique, we experiment with the scanner on both static geometry of a statue and dynamic geometry of a deforming material sample in front of the system.

  18. A digital 25 µm pixel-pitch uncooled amorphous silicon TEC-less VGA IRFPA with massive parallel Sigma-Delta-ADC readout

    NASA Astrophysics Data System (ADS)

    Weiler, Dirk; Russ, Marco; Würfel, Daniel; Lerch, Renee; Yang, Pin; Bauer, Jochen; Vogt, Holger

    2010-04-01

    This paper presents an advanced 640 x 480 (VGA) IRFPA based on uncooled microbolometers with a pixel-pitch of 25μm developed by Fraunhofer-IMS. The IRFPA is designed for thermal imaging applications in the LWIR (8 .. 14μm) range with a full-frame frequency of 30 Hz and a high sensitivity with NETD < 100 mK @ f/1. A novel readout architecture which utilizes massively parallel on-chip Sigma-Delta-ADCs located under the microbolometer array results in a high performance digital readout. Sigma-Delta-ADCs are inherently linear. A high resolution of 16 bit for a secondorder Sigma-Delta-modulator followed by a third-order digital sinc-filter can be obtained. In addition to several thousand Sigma-Delta-ADCs the readout circuit consists of a configurable sequencer for controlling the readout clocking signals and a temperature sensor for measuring the temperature of the IRFPA. Since packaging is a significant part of IRFPA's price Fraunhofer-IMS uses a chip-scaled package consisting of an IR-transparent window with antireflection coating and a soldering frame for maintaining the vacuum. The IRFPAs are completely fabricated at Fraunhofer-IMS on 8" CMOS wafers with an additional surface micromachining process. In this paper the architecture of the readout electronics, the packaging, and the electro-optical performance characterization are presented.

  19. 256 x 256 hybrid HgCdTe infrared focal plane arrays

    NASA Astrophysics Data System (ADS)

    Bailey, Robert B.; Kozlowski, Lester J.; Chen, Jenkon; Bui, Duc Q.; Vural, Kadri

    1991-05-01

    Hybrid HgCdTe 256 x 256 focal plane arrays have been developed to meet the sensitivity, resolution, and field-of-view requirements of high-performance medium-wavelength infrared (MWIR) imaging systems. The detector arrays for these hybrids are fabricated on substrates that reduce or eliminate the thermal expansion mismatch to the silicon readout circuit. The readouts are foundry-processed CMOS switched-FET circuits that have charge capacities greater than 107 electrons and a single video output capable of 10-MHz data rates. The high quantum efficiency, tunable absorption wavelength, and broad operating temperature range of these large HgCdTe staring focal plane arrays give them significant advantages over competing sensors. The mature Producible Alternative to CdTe for Epitaxy-1 (PACE-1) technology, using sapphire detector substrates, has demonstrated 256 x 256 MWIR arrays with mean laboratory noise equivalent temperature difference (NETO) of 9 mK for a 4.9-micron cutoff wavelength, 40-micron pixel size, and 80-K operating temperature. RMS detector response nonuniformities are less than 4 percent, and pixel yields are greater than 99 percent. The newly developed PACE-3 process uses silicon for the detector substrate to eliminate completely the thermal mismatch with the silicon readout circuit. It has the potential for similar performance in even larger array sizes. A 640 x 480 hybrid array is under development.

  20. Large format and high sensitivity VO x μ-bolometer detectors at SCD

    NASA Astrophysics Data System (ADS)

    Mizrahi, U.; Bikov, L.; Giladi, A.; Adin, A.; Shiloah, N.; Malkinson, E.; Czyzewski, T.; Seter, D.; Amsterdam, A.; Sinai, Y.; Fraenkel, A.

    2007-04-01

    SCD has established an uncooled detector product line based on the high-end VO x μ-bolometer technology. The first PFA launched was BIRD384, a 384x288 (or 320x240) configurable format with 25μm pitch. Typical NETD values for these FPAs are below 50mK with an F/1 aperture and 60 Hz frame rate. The product exhibits superior image uniformity, stability and reduced power consumption, making it most suitable for a broad range of "high-end" military and commercial applications. In this paper we report on our progress in development of new products in accordance with SCD's uncooled products roadmap: 1. A "sensitive" version of BIRD384 with an improved NETD of ~ 30mK @ F/1, 60Hz frame rate. This performance is achieved by optimizing concurrently the membrane structure, pixel architecture and ROIC electronics. 2. An improved version of BIRD384 ROIC that supports 100/120Hz frame rate and high dynamic range ("Fire Man" option). 3. First data of the BIRD640 - a 640x480 array with 25μm pitch and NETD <= 50mK @ F/1, 60Hz frame rate.

  1. Design trade-offs in ADC architectures dedicated to uncooled focal plane arrays

    NASA Astrophysics Data System (ADS)

    Robert, P.; Dupont, B.; Pochic, D.

    2008-04-01

    This paper presents two different architectures for the design of Analog to Digital Converters specifically adapted to infrared bolometric image sensors. Indeed, the increasing demand for integrated functions in uncooled readout circuits leads to on-chip ADC design as an interface between the internal analog core and the digital processing electronics. However specifying an on-chip ADC dedicated to focal plane array raises many questions about its architecture and its performance requirements. We will show that two architecture approaches are needed to cover the different sensor features in terms of array size and frame speed. A monolithic 14 bits ADC with a pipeline architecture, and a column 13 bits ADC with an original dual-ramp architecture, will be described. Finally, we will show measurement results to confirm the monolithic ADC is suitable for small array, as 160 x 120 with low frame speed, while a column ADC is more compliant for higher array, as 640 x 480 with a 60 Hz frame speed or 1024 x 768 arrays.

  2. DETAILED STUDIES OF ELECTRON COOLING FRICTION FORCE.

    SciTech Connect

    FEDOTOV, A.V.; BRUHWILER, D.L.; ABELL, D.T.; SIDORIN, A.O.

    2005-09-18

    High-energy electron cooling for RHIC presents many unique features and challenges. An accurate estimate of the cooling times requires detailed simulation of the electron cooling process. The first step towards such calculations is to have an accurate description of the cooling force. Numerical simulations are being used to explore various features of the friction force which appear due to several effects, including the anisotropy of the electron distribution in velocity space and the effect of a strong solenoidal magnetic field. These aspects are being studied in detail using the VORFAL code, which explicitly resolves close binary collisions. Results are compared with available asymptotic and empirical formulas and also, using the BETACOOL code, with direct numerical integration of less approximate expressions over the specified electron distribution function.

  3. Bolivia-Brazil gas line route detailed

    SciTech Connect

    Not Available

    1992-05-11

    This paper reports that state oil companies of Brazil and Bolivia have signed an agreement outlining the route for a 2,270 km pipeline system to deliver natural gas from Bolivian fields to Southeast Brazil. The two sides currently are negotiating details about construction costs as well as contract volumes and prices. Capacity is projected at 283-565 MMcfd. No official details are available, but Roberto Y. Hukai, a director of the Sao Paulo engineering company Jaako Poyry/Technoplan, estimates transportation cost of the Bolivian gas at 90 cents/MMBTU. That would be competitive with the price of gas delivered to the Sao Paulo gas utility Comgas, he the. Brazil's Petroleos Brasileiro SA estimates construction of the pipeline on the Brazilian side alone with cost $1.2-1.4 billion. Bolivia's Yacimientos Petroliferos Fiscales Bolivianos (YPFB) is negotiating with private domestic and foreign investors for construction of the Bolivian portion of the project.

  4. Langevin dynamics neglecting detailed balance condition.

    PubMed

    Ohzeki, Masayuki; Ichiki, Akihisa

    2015-07-01

    An improved method for driving a system into a desired distribution, for example, the Gibbs-Boltzmann distribution, is proposed, which makes use of an artificial relaxation process. The standard techniques for achieving the Gibbs-Boltzmann distribution involve numerical simulations under the detailed balance condition. In contrast, in the present study we formulate the Langevin dynamics, for which the corresponding Fokker-Planck operator includes an asymmetric component violating the detailed balance condition. This leads to shifts in the eigenvalues and results in the acceleration of the relaxation toward the steady state. The numerical implementation demonstrates faster convergence and shorter correlation time, and the technique of biased event sampling, Nemoto-Sasa theory, further highlights the efficacy of our method. PMID:26274123

  5. Detailed Studies of Electron Cooling Friction Force

    SciTech Connect

    Fedotov, A. V.; Bruhwiler, D. L.; Abell, D. T.; Sidorin, A. O.

    2006-03-20

    High-energy electron cooling for RHIC presents many unique features and challenges. An accurate estimate of the cooling times requires detailed simulation of the electron cooling process. The first step towards such calculations is to have an accurate description of the cooling force. Numerical simulations are being used to explore various features of the friction force which appear due to several effects, including the anisotropy of the electron distribution in velocity space and the effect of a strong solenoidal magnetic field. These aspects are being studied in detail using the VORPAL code, which explicitly resolves close binary collisions. Results are compared with available asymptotic and empirical formulas and also, using the BETACOOL code, with direct numerical integration of less approximate expressions over the specified electron distribution function.

  6. Detailed Jet Dynamics in a Collapsing Bubble

    NASA Astrophysics Data System (ADS)

    Supponen, Outi; Obreschkow, Danail; Kobel, Philippe; Farhat, Mohamed

    2015-12-01

    We present detailed visualizations of the micro-jet forming inside an aspherically collapsing cavitation bubble near a free surface. The high-quality visualizations of large and strongly deformed bubbles disclose so far unseen features of the dynamics inside the bubble, such as a mushroom-like flattened jet-tip, crown formation and micro-droplets. We also find that jetting near a free surface reduces the collapse time relative to the Rayleigh time.

  7. Detailed scour measurements around a debris accumulation

    USGS Publications Warehouse

    Mueller, David S.; Parola, Arthur C.

    1998-01-01

    Detailed scour measurements were made at Farm-Market 2004 over the Brazos River near Lake Jackson, Tex. during flooding in October 1994. Woody debris accumulations on bents 6, 7, and 8 obstructed flow through the bridge, causing scour of the streambed. Measurements at the site included three-dimensional velocities, channel bathymetry, water-surface elevations, water-surface slope, and discharge. Channel geometry upstream from the bridge caused approach conditions to be nonuniform.

  8. Structural concepts and details for seismic design

    SciTech Connect

    Not Available

    1991-09-01

    This manual discusses building and building component behavior during earthquakes, and provides suggested details for seismic resistance which have shown by experience to provide adequate performance during earthquakes. Special design and construction practices are also described which, although they might be common in some high-seismic regions, may not be common in low and moderate seismic-hazard regions of the United States. Special attention is given to describing the level of detailing appropriate for each seismic region. The UBC seismic criteria for all seismic zones is carefully examined, and many examples of connection details are given. The general scope of discussion is limited to materials and construction types common to Department of Energy (DOE) sites. Although the manual is primarily written for professional engineers engaged in performing seismic-resistant design for DOE facilities, the first two chapters, plus the introductory sections of succeeding chapters, contain descriptions which are also directed toward project engineers who authorize, review, or supervise the design and construction of DOE facilities. 88 refs., 188 figs.

  9. A Look Inside: MRI Shows the Detail

    ERIC Educational Resources Information Center

    Gosman, Derek; Rose, Mary Annette

    2015-01-01

    Understanding the advantages, risks, and financial costs of medical technology is one way that technologically literate citizens can make better-informed decisions regarding their health and medical care. A cascade of advancements in medical imaging technologies (Ulmer & Jansen 2010) offers an exciting backdrop from which to help students…

  10. IMAGES, IMAGES, IMAGES

    SciTech Connect

    Marcus, A.

    1980-07-01

    The role of images of information (charts, diagrams, maps, and symbols) for effective presentation of facts and concepts is expanding dramatically because of advances in computer graphics technology, increasingly hetero-lingual, hetero-cultural world target populations of information providers, the urgent need to convey more efficiently vast amounts of information, the broadening population of (non-expert) computer users, the decrease of available time for reading texts and for decision making, and the general level of literacy. A coalition of visual performance experts, human engineering specialists, computer scientists, and graphic designers/artists is required to resolve human factors aspects of images of information. The need for, nature of, and benefits of interdisciplinary effort are discussed. The results of an interdisciplinary collaboration are demonstrated in a product for visualizing complex information about global energy interdependence. An invited panel will respond to the presentation.

  11. Continuous thermal infrared monitoring at Campi Flegrei and Vesuvius (Italy) by automated data processing: an effective surveillance tool of active volcanoes

    NASA Astrophysics Data System (ADS)

    Sansivero, Fabio; Vilardo, Giuseppe

    2014-05-01

    The INGV-Osservatorio Vesuviano Thermal Infrared Imagery Monitoring Network (TIIMNet) is made up of IR acquisition stations designed to continuously acquire IR scenes of diffuse degassing areas in the Neapolitan volcanic district. Every station consists of a RMS (Remote Monitoring Station) which manages the shooting functionalities of the IR camera and the connection to the surveillance Centre of INGV-Osservatorio Vesuviano in Naples. The first developed station was equipped with a NEC Thermo Tracer TS7302 IR camera (with 320x240 pixel FPA uncooled microbolometer); a newer one is equipped with a FLIR SC645 IR camera (with 640x480 pixel FPA uncooled microbolometer) and is supported by an in-house developed hardware which manages a fully real-time control of data acquisition and transfer procedures. As a whole, TIIMNet is composed of four permanent stations and three transportable ones. The first permanent NEC Station was installed at Vesuvius on July 2004 and dismissed on May 2007. A new permanent FLIR Station was set up on June 2011 and it acquires IR scenes from the inner SW slope of Vesuvius crater. In the Campi Flegrei caldera (Pozzuoli, Italy) a permanent NEC Station was operative at Solfatara since September 2004 and it acquired scenes of the major fumaroles area located on the SE inner slope at the intersection of two active, SW-NE and NW-SE main faults. A permanent FLIR Station has been installed at Solfatara on June 2013 and takes IR shots of a significant thermal anomaly on the Northern inner slope of the crater. At Pisciarelli locality, on the Solfatara NE outer slope, a transportable NEC Station was set up on October 2006 and dismissed on September 2013. It was abreast of a permanent FLIR Station on March 2013. Both stations stored IR scenes of the outer eastern flank of the Solfatara tuff-cone characterized by heavy water vapor and CO2 emissions close to an active NW-SE fault. IR scenes are acquired every night by the TIIMNet stations and in real time

  12. Revisiting the Seductive Details Effect in Multimedia Learning: Context-Dependency of Seductive Details

    ERIC Educational Resources Information Center

    Ozdemir, Devrim; Doolittle, Peter

    2015-01-01

    The purpose of this study was to investigate the effects of context-dependency of seductive details on recall and transfer in multimedia learning environments. Seductive details were interesting yet irrelevant sentences in the instructional text. Two experiments were conducted. The purpose of Experiment 1 was to identify context-dependent and…

  13. Towards a detailed soot model for internal combustion engines

    SciTech Connect

    Mosbach, Sebastian; Celnik, Matthew S.; Raj, Abhijeet; Kraft, Markus; Zhang, Hongzhi R.; Kubo, Shuichi; Kim, Kyoung-Oh

    2009-06-15

    In this work, we present a detailed model for the formation of soot in internal combustion engines describing not only bulk quantities such as soot mass, number density, volume fraction, and surface area but also the morphology and chemical composition of soot aggregates. The new model is based on the Stochastic Reactor Model (SRM) engine code, which uses detailed chemistry and takes into account convective heat transfer and turbulent mixing, and the soot formation is accounted for by SWEEP, a population balance solver based on a Monte Carlo method. In order to couple the gas-phase to the particulate phase, a detailed chemical kinetic mechanism describing the combustion of Primary Reference Fuels (PRFs) is extended to include small Polycyclic Aromatic Hydrocarbons (PAHs) such as pyrene, which function as soot precursor species for particle inception in the soot model. Apart from providing averaged quantities as functions of crank angle like soot mass, volume fraction, aggregate diameter, and the number of primary particles per aggregate for example, the integrated model also gives detailed information such as aggregate and primary particle size distribution functions. In addition, specifics about aggregate structure and composition, including C/H ratio and PAH ring count distributions, and images similar to those produced with Transmission Electron Microscopes (TEMs), can be obtained. The new model is applied to simulate an n-heptane fuelled Homogeneous Charge Compression Ignition (HCCI) engine which is operated at an equivalence ratio of 1.93. In-cylinder pressure and heat release predictions show satisfactory agreement with measurements. Furthermore, simulated aggregate size distributions as well as their time evolution are found to qualitatively agree with those obtained experimentally through snatch sampling. It is also observed both in the experiment as well as in the simulation that aggregates in the trapped residual gases play a vital role in the soot

  14. Optical versus radiographic magnification for fine-detail skeletal radiography.

    PubMed

    Genant, H K; Doi, K; Mall, J C

    1975-01-01

    Fine-detail radiographic techniques for peripheral skeletal imaging have gained wide clinical acceptance. In this study, the imaging properties and clinical applications of the optical magnification technique, which employs fine-grain industrial film and a large focal spot, are compared quantitatively and qualitatively with those of three slow screen-film techniques, namely, contact exposure with a large focal spot, 2 times radiographic magnification with a 0.3 mm focal spot, and 4 times radiographic magnification with a 50 mu focal spot. The modulation transfer functions (MTF's) of the recording systems and focal spots are obtained and film sensitometry performed. Clinical comparisons are made for patients with metabolic, arthritic, and neoplastic skeletal disorders. The results illustrate the superiority of the optical magnification technique over contact or 2 times magnification techniques using slow screen-film systems. If a microfocus tube is used, however, direct radiographic magnification may provide images comparable in resolution, noise and contrast to those made with the optical magnification technique, and at lower radiation exposure to the patient. PMID:46857

  15. Venus - Detailed mapping of Maxwell Montes region

    NASA Astrophysics Data System (ADS)

    Alexandrov, Yu. N.; Crymov, A. A.; Kotelnikov, V. A.; Petrov, G. M.; Rzhiga, O. N.; Sidorenko, A. I.; Sinilo, V. P.; Zakharov, A. I.; Akim, E. L.; Basilevski, A. T.; Kadnichanski, S. A.; Tjuflin, Yu. S.

    1986-03-01

    From October 1983 to July 1984, the north hemisphere of Venus, from latitude 30° to latitude 90°, was mapped by means of the radar imagers and altimeters of the spacecraft Venera 15 and Venera 16. This report presents the results of the radar mapping of the Maxwell Montes region, one of the most interesting features of Venus' surface. A radar mosaic map and contour map have been compiled.

  16. Venus: detailed mapping of maxwell montes region.

    PubMed

    Alexandrov, Y N; Crymov, A A; Kotelnikov, V A; Petrov, G M; Rzhiga, O N; Sidorenko, A I; Sinilo, V P; Zakharov, A I; Akim, E L; Basilevski, A T; Kadnichanski, S A; Tjuflin, Y S

    1986-03-14

    From October 1983 to July 1984, the north hemisphere of Venus, from latitude 30 degrees to latitude 90 degrees , was mapped by means of the radar imagers and altimeters of the spacecraft Venera 15 and Venera 16. This report presents the results of the radar mapping of the Maxwell Montes region, one of the most interesting features of Venus' surface. A radar mosaic map and contour map have been compiled. PMID:17839563

  17. Violation of detailed balance accelerates relaxation

    NASA Astrophysics Data System (ADS)

    Ichiki, Akihisa; Ohzeki, Masayuki

    2013-08-01

    Recent studies have experienced the acceleration of convergence in Markov chain Monte Carlo methods implemented by the systems without detailed balance condition (DBC). However, such advantage of the violation of DBC has not been confirmed in general. We investigate the effect of the absence of DBC on the convergence toward equilibrium. Surprisingly, it is shown that the DBC violation always makes the relaxation faster. Our result implies the existence of a kind of thermodynamic inequality that connects the nonequilibrium process relaxing toward steady state with the relaxation process which has the same probability distribution as its equilibrium state.

  18. A detailed phylogeny for the Methanomicrobiales

    NASA Technical Reports Server (NTRS)

    Rouviere, P.; Mandelco, L.; Winker, S.; Woese, C. R.

    1992-01-01

    The small subunit rRNA sequence of twenty archaea, members of the Methanomicrobiales, permits a detailed phylogenetic tree to be inferred for the group. The tree confirms earlier studies, based on far fewer sequences, in showing the group to be divided into two major clusters, temporarily designated the "methanosarcina" group and the "methanogenium" group. The tree also defines phylogenetic relationships within these two groups, which in some cases do not agree with the phylogenetic relationships implied by current taxonomic names--a problem most acute for the genus Methanogenium and its relatives. The present phylogenetic characterization provides the basis for a consistent taxonomic restructuring of this major methanogenic taxon.

  19. Instrumentation for detailed bridge-scour measurements

    USGS Publications Warehouse

    Landers, Mark N.; Mueller, David S.; Trent, Roy E.

    1993-01-01

    A portable instrumentation system is being developed to obtain channel bathymetry during floods for detailed bridge-scour measurements. Portable scour measuring systems have four components: sounding instrument, horizontal positioning instrument, deployment mechanisms, and data storage device. The sounding instrument will be a digital fathometer. Horizontal position will be measured using a range-azimuth based hydrographic survey system. The deployment mechanism designed for this system is a remote-controlled boat using a small waterplane area, twin-hull design. An on-board computer and radio will monitor the vessel instrumentation, record measured data, and telemeter data to shore.

  20. Details of extensive movements by Minnesota wolves

    USGS Publications Warehouse

    Merrill, S.B.; Mech, L.D.

    2000-01-01

    We used VHF, GPS, and satellite radiocollars to study details of long distance movements by four Minnesota wolves (Canis lupus). Number of locations during our tracking ranged from 14 to 274. Farthest distances reached ranged from 183-494 km, and minimum distances traveled (sums of line segments) ranged from 490-4251 km. Numbers of times wolves crossed state, provincial or interstate highways ranged from 1 to 215. All four of the wolves returned to or near their natal territories after up to 179 d and at least two left again.

  1. VLBA Movies Reveal New Details of Cosmic Jets

    NASA Astrophysics Data System (ADS)

    2008-01-01

    Astronomers have known for decades that supermassive black holes at the cores of galaxies can shoot out jets of subatomic particles at tremendous speeds. However, details about the physics of such jets, including how they are generated, how the high-speed flows are shaped into jets, and how fast the particles are moving, among many others, have remained elusive. An international team of researchers now is making an unprecedented long-term study of the motions of these giant jets, using the super-sharp imaging capabilities of the National Science Foundation's Very Long Baseline Array (VLBA). "We're making images of 200 galactic jets at regular intervals, tracking their motions and studying their magnetic-field properties. This is making major contributions to our understanding of such jets," said Matthew Lister, of Purdue University. MOJAVE Poster Click image for high-resolution file (11.9 MB) The research team has produced time-lapse movies of 100 of the jets, allowing measurement of the speed and direction of motion. "The results of these VLBA observations are going into a rich and still-growing set of data that is available to the entire astronomical research community as a tool for understanding the many unresolved questions we have about these jets," Lister said. The jet study is called MOJAVE -- Monitoring Of Jets in Active galactic nuclei with VLBA Experiments -- and began in 2002. It is a successor to an earlier VLBA study that regularly made images of nearly 200 jets from 1994 to 2002. The jets are powered by the gravitational energy of black holes containing hundreds of millions times more mass than the Sun. Black holes are concentrations of mass so dense that not even light can escape them. As these monsters draw material toward them, the material falls into a circular disk orbiting the black hole. The jets are propelled outward along the poles of the disk. The MOJAVE movies have given astronomers some surprises and also have spurred follow-on studies of

  2. Chord, Tie Bar & Crossbracing Joint Detail in Plan; Crossbracing ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Chord, Tie Bar & Crossbracing Joint Detail in Plan; Crossbracing Center Joint Detail in Plan; Chord Joining Detail in Plan & Elevation; Chord, Panel Post, Tie Bar, & Diagonal Brace Joint Detail; Crossbracing Center Joint Detail in Section; Chord, Panel Post, Tie Bar & Horizontal Brace Joint Detail - Narrows Bridge, Spanning Sugar Creek at Old County Road 280 East, Marshall, Parke County, IN

  3. Detailed balance of the Feynman micromotor

    NASA Astrophysics Data System (ADS)

    Abbott, Derek; Davis, Bruce R.; Parrondo, Juan M. R.

    1999-09-01

    One existing implication of micromotors is that they can be powered by rectifying non-equilibrium thermal fluctuations or mechanical vibrations via the so-called Feynman- micromotor. An example of mechanical rectification is found in the batteryless wristwatch. The original concept was described in as early as 1912 by Smoluchowski and was later revisited in 1963 by Feynman, in the context of rectifying thermal fluctuations to obtain useful motion. It has been shown that, although rectification is impossible at equilibrium, it is possible for the Feynman-micromotor to perform work under non-equilibrium conditions. These concepts can now be realized by MEMS technology and may have exciting implications in biomedicine - where the Feynman- micromotor can be used to power a smart pill, for example. Previously, Feynman's analysis of the motor's efficiency has been shown to be flawed by Parrondo and Espanol. We now show there are further problems in Feynman's treatment of detailed balance. In order to design and understand this device correctly, the equations of detailed balance must be found. Feynman's approach was to use probabilities based on energies and we show that this is problematic. In this paper, we demonstrate corrected equations using level crossing probabilities instead. A potential application of the Feynman-micromotor is a batteryless nanopump that consists of a small MEMS chip that adheres to the skin of a patient and dispense nanoliter quantities of medication. Either mechanical or thermal rectification via a Feynman- micromotor, as the power source, is open for possible investigation.

  4. Detailed Chemical Kinetic Modeling of Hydrazine Decomposition

    NASA Technical Reports Server (NTRS)

    Meagher, Nancy E.; Bates, Kami R.

    2000-01-01

    The purpose of this research project is to develop and validate a detailed chemical kinetic mechanism for gas-phase hydrazine decomposition. Hydrazine is used extensively in aerospace propulsion, and although liquid hydrazine is not considered detonable, many fuel handling systems create multiphase mixtures of fuels and fuel vapors during their operation. Therefore, a thorough knowledge of the decomposition chemistry of hydrazine under a variety of conditions can be of value in assessing potential operational hazards in hydrazine fuel systems. To gain such knowledge, a reasonable starting point is the development and validation of a detailed chemical kinetic mechanism for gas-phase hydrazine decomposition. A reasonably complete mechanism was published in 1996, however, many of the elementary steps included had outdated rate expressions and a thorough investigation of the behavior of the mechanism under a variety of conditions was not presented. The current work has included substantial revision of the previously published mechanism, along with a more extensive examination of the decomposition behavior of hydrazine. An attempt to validate the mechanism against the limited experimental data available has been made and was moderately successful. Further computational and experimental research into the chemistry of this fuel needs to be completed.

  5. A Detailed Chemical Kinetic Model for TNT

    SciTech Connect

    Pitz, W J; Westbrook, C K

    2005-01-13

    A detailed chemical kinetic mechanism for 2,4,6-tri-nitrotoluene (TNT) has been developed to explore problems of explosive performance and soot formation during the destruction of munitions. The TNT mechanism treats only gas-phase reactions. Reactions for the decomposition of TNT and for the consumption of intermediate products formed from TNT are assembled based on information from the literature and on current understanding of aromatic chemistry. Thermodynamic properties of intermediate and radical species are estimated by group additivity. Reaction paths are developed based on similar paths for aromatic hydrocarbons. Reaction-rate constant expressions are estimated from the literature and from analogous reactions where the rate constants are available. The detailed reaction mechanism for TNT is added to existing reaction mechanisms for RDX and for hydrocarbons. Computed results show the effect of oxygen concentration on the amount of soot precursors that are formed in the combustion of RDX and TNT mixtures in N{sub 2}/O{sub 2} mixtures.

  6. MAGNIFICENT DETAILS IN A DUSTY SPIRAL GALAXY

    NASA Technical Reports Server (NTRS)

    2002-01-01

    In 1995, the majestic spiral galaxy NGC 4414 was imaged by the Hubble Space Telescope as part of the HST Key Project on the Extragalactic Distance Scale. An international team of astronomers, led by Dr. Wendy Freedman of the Observatories of the Carnegie Institution of Washington, observed this galaxy on 13 different occasions over the course of two months. Images were obtained with Hubble's Wide Field Planetary Camera 2 (WFPC2) through three different color filters. Based on their discovery and careful brightness measurements of variable stars in NGC 4414, the Key Project astronomers were able to make an accurate determination of the distance to the galaxy. The resulting distance to NGC 4414, 19.1 megaparsecs or about 60 million light-years, along with similarly determined distances to other nearby galaxies, contributes to astronomers' overall knowledge of the rate of expansion of the universe. The Hubble constant (H0) is the ratio of how fast galaxies are moving away from us to their distance from us. This astronomical value is used to determine distances, sizes, and the intrinsic luminosities for many objects in our universe, and the age of the universe itself. Due to the large size of the galaxy compared to the WFPC2 detectors, only half of the galaxy observed was visible in the datasets collected by the Key Project astronomers in 1995. In 1999, the Hubble Heritage Team revisited NGC 4414 and completed its portrait by observing the other half with the same filters as were used in 1995. The end result is a stunning full-color look at the entire dusty spiral galaxy. The new Hubble picture shows that the central regions of this galaxy, as is typical of most spirals, contain primarily older, yellow and red stars. The outer spiral arms are considerably bluer due to ongoing formation of young, blue stars, the brightest of which can be seen individually at the high resolution provided by the Hubble camera. The arms are also very rich in clouds of interstellar dust

  7. Detailed Cloud Patterns in Martian Northern Hemisphere

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Cold and cloudy mornings; cool, hazy afternoons. High winds aloft and weather fronts moving slowly to the east. It is winter in the Martian northern hemisphere. One of the many reasons to study Mars is that, at times, its weather is very 'Earth-like.' At this time of the Martian year, clouds are abundant, especially in the morning and especially in the high northern latitudes. Clouds and fogs are also observed in low-lying areas farther to the south, in some lowlands they are as far south as the equator.

    The above color composite images, obtained by Mars Global Surveyor's camera on June 4, 1998, illustrate this Martian 'weather report.' Most of the thick, white clouds seen here occur north of latitude 35oN (roughly equivalent to Albuquerque NM, Memphis TN, and Charlotte, NC). Fog (seen as bright orange because it is lighter than the ground but some of the ground is still visible) occupies the lowest portions of the Kasei Valles outflow channel around 30oN and at 25oN.

    Several different types of cloud features are seen. The repetitious, wash-board pattern of parallel lines are 'gravity wave clouds'. These commonly form, in the lee--downwind side-- of topographic features such as mountain ranges (on Earth) or crater rims (on Mars), under very specific atmospheric conditions (low temperatures, high humidity, and high wind speeds). In this area, the wave clouds are lower in the atmosphere than some of the other clouds. These other clouds show attributes reflecting more the regional weather pattern, occasionally showing the characteristic 'slash' shape (southwest to northeast) of a weather front. These clouds probably contain mostly crystals of water ice but, depending on the temperature at high altitude (and more likely closer to the pole), some could also contain frozen carbon dioxide ('dry ice').

    MOC images 34501 (the red wide angle image) and 34502 (the blue wide angle image) were obtained on Mars Global Surveyor's 345th orbit about the planet

  8. Detailed assays conducted on Vietnamese crude oils

    SciTech Connect

    Du, P.Q. )

    1990-07-16

    More oil property data, in the form of recent crude oil assays, have been made available for two Vietnamese crude oils, Bach Ho (White Tiger) and Dai Hung (Big Bear). Crude oil data presented earlier gave limited properties of the crudes,which are from the Miocene formations. Further analyses have been conducted on Bach Ho crude from the Oligocene formations. Production from Oligocene is far more representative of the oils produced from the Bach Ho field and marketed worldwide. Currently, Bach Ho is the only producing field. Dai Hung is expected to be in production during the next few years. Bach Ho is currently producing at the rate of 20,000 b/d. That figure is projected to grow to 100,000 b/d by 1992 and to 120,000 b/d by 1995. Detailed assays of both crude oils are presented.

  9. Detailed mechanism for oxidation of benzene

    NASA Technical Reports Server (NTRS)

    Bittker, David A.

    1990-01-01

    A detailed mechanism for the oxidation of benzene is presented and used to compute experimentally obtained concentration profiles and ignition delay times over a wide range of equivalence ratio and temperature. The computed results agree qualitatively with all the experimental trends. Quantitative agreement is obtained with several of the composition profiles and for the temperature dependence of the ignition delay times. There are indications, however, that some important reactions are as yet undiscovered in this mechanism. Recent literature expressions have been used for the rate coefficients of most important reactions, except for some involving phenol. The discrepancy between the phenol pyrolysis rate coefficient used in this work and a recent literature expression remains to be explained.

  10. Report Details Solar Radiation Alert and Recommendations

    NASA Astrophysics Data System (ADS)

    Staedter, Tracy

    2006-06-01

    High-energy particles from the Sun and from regions beyond the solar system constantly bombard Earth. Thanks to the planet's atmosphere and magnetic field, comsic radiation is not a significant threat to those rooted on terra firma. But airline crew and passengers flying at high altitudes, or over the poles where the Earth's magnetic field provides no protection, are particularly vulnerable to unpredictable flares on the Sun's surface that launch streams of sub-atomic particles toward Earth. The report, ``Solar Radiation Alert System,'' published by the Federal Aviation Administration (FAA) and the Cooperative Institute for Research in Environmental Sciences (CIRES) at the University of Colorado, Boulder, in July 2005 (www.faa.gov/library/reports/medical/oamtechreports/2000s/media/0514.pdf) details in alert system designed to estimate the ionizing radiation at aircraft flight altitudes and, depending on the resulting dose rate, issue a warning.

  11. Picornavirus uncoating intermediate captured in atomic detail

    PubMed Central

    Ren, Jingshan; Wang, Xiangxi; Hu, Zhongyu; Gao, Qiang; Sun, Yao; Li, Xuemei; Porta, Claudine; Walter, Thomas S.; Gilbert, Robert J.; Zhao, Yuguang; Axford, Danny; Williams, Mark; McAuley, Katherine; Rowlands, David J.; Yin, Weidong; Wang, Junzhi; Stuart, David I.; Rao, Zihe; Fry, Elizabeth E.

    2013-01-01

    It remains largely mysterious how the genomes of non-enveloped eukaryotic viruses are transferred across a membrane into the host cell. Picornaviruses are simple models for such viruses, and initiate this uncoating process through particle expansion, which reveals channels through which internal capsid proteins and the viral genome presumably exit the particle, although this has not been clearly seen until now. Here we present the atomic structure of an uncoating intermediate for the major human picornavirus pathogen CAV16, which reveals VP1 partly extruded from the capsid, poised to embed in the host membrane. Together with previous low-resolution results, we are able to propose a detailed hypothesis for the ordered egress of the internal proteins, using two distinct sets of channels through the capsid, and suggest a structural link to the condensed RNA within the particle, which may be involved in triggering RNA release. PMID:23728514

  12. Capture barrier distributions: Some insights and details

    SciTech Connect

    Rowley, N.; Grar, N.; Trotta, M.

    2007-10-15

    The 'experimental barrier distribution' provides a parameter-free representation of experimental heavy-ion capture cross sections that highlights the effects of entrance-channel couplings. Its relation to the s-wave transmission is discussed, and in particular it is shown how the full capture cross section can be generated from an l=0 coupled-channels calculation. Furthermore, it is shown how this transmission can be simply exploited in calculations of quasifission and evaporation-residue cross sections. The system {sup 48}Ca+{sup 154}Sm is studied in detail. A calculation of the compound-nucleus spin distribution reveals a possible energy dependence of barrier weights due to polarization arising from target and projectile quadrupole phonon states; this effect also gives rise to an entrance-channel 'extra-push'.

  13. Imaging Atherosclerosis.

    PubMed

    Tarkin, Jason M; Dweck, Marc R; Evans, Nicholas R; Takx, Richard A P; Brown, Adam J; Tawakol, Ahmed; Fayad, Zahi A; Rudd, James H F

    2016-02-19

    Advances in atherosclerosis imaging technology and research have provided a range of diagnostic tools to characterize high-risk plaque in vivo; however, these important vascular imaging methods additionally promise great scientific and translational applications beyond this quest. When combined with conventional anatomic- and hemodynamic-based assessments of disease severity, cross-sectional multimodal imaging incorporating molecular probes and other novel noninvasive techniques can add detailed interrogation of plaque composition, activity, and overall disease burden. In the catheterization laboratory, intravascular imaging provides unparalleled access to the world beneath the plaque surface, allowing tissue characterization and measurement of cap thickness with micrometer spatial resolution. Atherosclerosis imaging captures key data that reveal snapshots into underlying biology, which can test our understanding of fundamental research questions and shape our approach toward patient management. Imaging can also be used to quantify response to therapeutic interventions and ultimately help predict cardiovascular risk. Although there are undeniable barriers to clinical translation, many of these hold-ups might soon be surpassed by rapidly evolving innovations to improve image acquisition, coregistration, motion correction, and reduce radiation exposure. This article provides a comprehensive review of current and experimental atherosclerosis imaging methods and their uses in research and potential for translation to the clinic. PMID:26892971

  14. Imaging Atherosclerosis

    PubMed Central

    Tarkin, Jason M.; Dweck, Marc R.; Evans, Nicholas R.; Takx, Richard A.P.; Brown, Adam J.; Tawakol, Ahmed; Fayad, Zahi A.

    2016-01-01

    Advances in atherosclerosis imaging technology and research have provided a range of diagnostic tools to characterize high-risk plaque in vivo; however, these important vascular imaging methods additionally promise great scientific and translational applications beyond this quest. When combined with conventional anatomic- and hemodynamic-based assessments of disease severity, cross-sectional multimodal imaging incorporating molecular probes and other novel noninvasive techniques can add detailed interrogation of plaque composition, activity, and overall disease burden. In the catheterization laboratory, intravascular imaging provides unparalleled access to the world beneath the plaque surface, allowing tissue characterization and measurement of cap thickness with micrometer spatial resolution. Atherosclerosis imaging captures key data that reveal snapshots into underlying biology, which can test our understanding of fundamental research questions and shape our approach toward patient management. Imaging can also be used to quantify response to therapeutic interventions and ultimately help predict cardiovascular risk. Although there are undeniable barriers to clinical translation, many of these hold-ups might soon be surpassed by rapidly evolving innovations to improve image acquisition, coregistration, motion correction, and reduce radiation exposure. This article provides a comprehensive review of current and experimental atherosclerosis imaging methods and their uses in research and potential for translation to the clinic. PMID:26892971

  15. Preference for Well-Balanced Saliency in Details Cropped from Photographs

    PubMed Central

    Abeln, Jonas; Fresz, Leonie; Amirshahi, Seyed Ali; McManus, I. Chris; Koch, Michael; Kreysa, Helene; Redies, Christoph

    2016-01-01

    Photographic cropping is the act of selecting part of a photograph to enhance its aesthetic appearance or visual impact. It is common practice with both professional (expert) and amateur (non-expert) photographers. In a psychometric study, McManus et al. (2011b) showed that participants cropped photographs confidently and reliably. Experts tended to select details from a wider range of positions than non-experts, but other croppers did not generally prefer details that were selected by experts. It remained unclear, however, on what grounds participants selected particular details from a photograph while avoiding other details. One of the factors contributing to cropping decision may be visual saliency. Indeed, various saliency-based computer algorithms are available for the automatic cropping of photographs. However, careful experimental studies on the relation between saliency and cropping are lacking to date. In the present study, we re-analyzed the data from the studies by McManus et al. (2011a,b), focusing on statistical image properties. We calculated saliency-based measures for details selected and details avoided during cropping. As expected, we found that selected details contain regions of higher saliency than avoided details on average. Moreover, the saliency center-of-mass was closer to the geometrical center in selected details than in avoided details. Results were confirmed in an eye tracking study with the same dataset of images. Interestingly, the observed regularities in cropping behavior were less pronounced for experts than for non-experts. In summary, our results suggest that, during cropping, participants tend to select salient regions and place them in an image composition that is well-balanced with respect to the distribution of saliency. Our study contributes to the knowledge of perceptual bottom-up features that are germane to aesthetic decisions in photography and their variability in non-experts and experts. PMID:26793086

  16. Shocking Detail of Superstar's Activity Revealed

    NASA Astrophysics Data System (ADS)

    1999-10-01

    NASA's Chandra X-ray Observatory has imaged Eta Carinae and revealed a hot inner core around this mysterious superstar. The new X-ray observation shows three distinct structures: an outer, horseshoe shaped ring about two light years in diameter, a hot inner core about 3 light months in diameter, and a hot central source less than a light month in diameter which may contain the superstar. All three structures are thought to represent shock waves produced by matter rushing away from the superstar at supersonic speeds. The temperature of the shock-heated gas ranges from 60 million degrees Celsius in the central regions to 3 million degrees Celsius on the outer structure. An earlier image of Eta Carinae by the Hubble Space Telescope revealed two spectacular bubbles of gas expanding in opposite directions away from a central bright region at speeds in excess of a million miles per hour. The inner region visible in the Chandra image has never been resolved before, and appears to be associated with a central disk of high velocity gas rushing out at much higher speeds perpendicular to the bipolar optical nebula. "It is not what I expected," said Dr. Fred Seward of the Harvard-Smithsonian Center for Astrophysics. "I expected to see a strong point source with a little diffuse emission cloud around it. Instead, we see just the opposite- a bright cloud of diffuse emission, and much less radiation from the center." "The Chandra image contains some puzzles for existing ideas of how a star can produce such hot and intense X-rays," agreed Prof. Kris Davidson of the University of Minnesota. "In the most popular theory, X-rays are made by colliding gas streams from two stars so close together that they'd look like a point source to us. But what happens to gas streams that escape to farther distances? The extended hot stuff in the middle of the new image gives demanding new conditions for any theory to meet." Eta Carinae is one of the most enigmatic and intriguing objects in our

  17. A detailed analysis of Mariner nine TV navigation data.

    NASA Technical Reports Server (NTRS)

    Breckenridge, W. G.; Acton, C. H., Jr.

    1972-01-01

    Mariner 9 data analysis showed a good performance of the Mars probe planetary approach navigation systems and a good agreement between measured and predicted probe-approach characteristics. It was found that all operations were completed on time and that the calibration of the instruments and the observation of a greater-than-planned number of stars resulted in a higher-than-expected measurement accuracy. The key instruments of the Mariner were TV cameras taking pictures of Phobos and Deimos against a background of stars, calibrated sun and star sensors, and a scan platform. The error models used for optical navigation system elements, the calibration of the scan platform and of the TV cameras, and the image detection and location techniques are discussed in detail.

  18. 39. CLOSE UP DETAIL OF THE FEEDER AND STAMP CONNECTION. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    39. CLOSE UP DETAIL OF THE FEEDER AND STAMP CONNECTION. THE STAMP AN MORTAR BOX ARE ON THE LEFT AND THE FEEDER WITH ITS FEEDER DISK IS ON THE RIGHT. NOTE THE COLLAR ON THE CENTER STAMP STEM (UPPER LEFT CORNER OF THE IMAGE) THAT ACTIVATES THE LEVER IN THE CENTER OF THE PHOTO. THE COLLAR IS POSITIONED SUCH THAT WHEN THE LEVEL OF THE MATERIAL REACHES A LOW POINT IN THE MORTAR BOX IT PUSHES DOWN ON THE LEVER WHICH IN TURN ACTIVATES THE AUTOMATIC FEEDER DRIVE MECHANISM WHICH THEM DELIVERS ORE INTO THE BACKSIDE OF THE MORTAR BOX. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

  19. Gigantic Cosmic Corkscrew Reveals New Details About Mysterious Microquasar

    NASA Astrophysics Data System (ADS)

    2004-10-01

    Making an extra effort to image a faint, gigantic corkscrew traced by fast protons and electrons shot out from a mysterious microquasar paid off for a pair of astrophysicists who gained new insights into the beast's inner workings and also resolved a longstanding dispute over the object's distance. Microquasar SS 433 VLA Image of Microquasar SS 433 CREDIT: Blundell & Bowler, NRAO/AUI/NSF (Click on Image for Larger Version) The astrophysicists used the National Science Foundation's Very Large Array (VLA) radio telescope to capture the faintest details yet seen in the plasma jets emerging from the microquasar SS 433, an object once dubbed the "enigma of the century." As a result, they have changed scientists' understanding of the jets and settled the controversy over its distance "beyond all reasonable doubt," they said. SS 433 is a neutron star or black hole orbited by a "normal" companion star. The powerful gravity of the neutron star or black hole draws material from the stellar wind of its companion into an accretion disk of material tightly circling the dense central object prior to being pulled onto it. This disk propels jets of fast protons and electrons outward from its poles at about a quarter of the speed of light. The disk in SS 433 wobbles like a child's top, causing its jets to trace a corkscrew in the sky every 162 days. The new VLA study indicates that the speed of the ejected particles varies over time, contrary to the traditional model for SS 433. "We found that the actual speed varies between 24 percent to 28 percent of light speed, as opposed to staying constant," said Katherine Blundell, of the University of Oxford in the United Kingdom. "Amazingly, the jets going in both directions change their speeds simultaneously, producing identical speeds in both directions at any given time," Blundell added. Blundell worked with Michael Bowler, also of Oxford. The scientists' findings have been accepted by the Astrophysical Journal Letters. SS 433 New VLA

  20. Study of the detail content of Apollo orbital photography

    NASA Technical Reports Server (NTRS)

    Kinzly, R. E.

    1972-01-01

    The results achieved during a study of the Detail Content of Apollo Orbital Photography are reported. The effect of residual motion smear or image reproduction processes upon the detail content of lunar surface imagery obtained from the orbiting command module are assessed. Data and conclusions obtained from the Apollo 8, 12, 14 and 15 missions are included. For the Apollo 8, 12 and 14 missions, the bracket-mounted Hasselblad camera had no mechanism internal to the camera for motion compensation. If the motion of the command module were left totally uncompensated, these photographs would exhibit a ground smear varying from 12 to 27 meters depending upon the focal length of the lens and the exposure time. During the photographic sequences motion compensation was attempted by firing the attitude control system of the spacecraft at a rate to compensate for the motion relative to the lunar surface. The residual smear occurring in selected frames of imagery was assessed using edge analyses methods to obtain and achieved modulation transfer function (MTF) which was compared to a baseline MTF.

  1. Description of Axial Detail for ROK Fuel

    SciTech Connect

    Trellue, Holly R; Galloway, Jack D

    2012-04-20

    For the purpose of NDA simulations of the ROK fuel assemblies, we have developed an axial burnup distribution to represent the pins themselves based on gamma scans of rods in the G23 assembly. For the purpose of modeling the G23 assembly (both at ORNL and LANL), the pin-by-pin burnup map as simulated by ROK is being assumed to represent the radial burnup distribution. However, both DA and NDA results indicate that this simulated estimate is not 100% correct. In particular, the burnup obtained from the axial gamma scan of 7 pins does not represent exactly the same 'average' pin burnup as the ROK simulation. Correction for this discrepancy is a goal of the well-characterized assembly task but will take time. For now, I have come up with a correlation for 26 axial points of the burnup as obtained by gamma scans of 7 different rods (C13, G01, G02, J11, K10, L02, and M04, neglecting K02 at this time) to the average burnup given by the simulation for each of the rods individually. The resulting fraction in each axial zone is then averaged for the 7 different rods so that it can represent every fuel pin in the assembly. The burnup in each of the 26 axial zones of rods in all ROK assemblies will then be directly adjusted using this fraction, which is given in Table 1. Note that the gamma scan data given by ROK for assembly G23 included a length of {approx}3686 mm, so the first 12 mm and the last 14 mm were ignored to give an actual rod length of {approx}366 cm. To represent assembly F02 in which no pin-by-pin burnup distribution is given by ROK, we must model it using infinitely-reflected geometry but can look at the effects of measuring in different axial zones by using intermediate burnup files (i.e. smaller burnups than 28 GWd/MTU) and determining which axial zone(s) each burnup represents. Details for assembly F02 are then given in Tables 2 and 3, which is given in Table 1 and has 44 total axial zones to represent the top meter in explicit detail in addition to the

  2. Image transfer protocol in progressively increasing resolution

    NASA Technical Reports Server (NTRS)

    Percival, Jeffrey W. (Inventor); White, Richard L. (Inventor)

    1999-01-01

    A method of transferring digital image data over a communication link transforms and orders the data so that, as data is received by a receiving station, a low detail version of the image is immediately generated with later transmissions of data providing progressively greater detail in this image. User instructions are accepted, limiting the ultimate resolution of the image or suspending enhancement of the image except in certain user defined regions. When a low detail image is requested followed by a request for a high detailed version of the same image, the originally transmitted data of the low resolution image is not discarded or retransmitted but used with later data to improve the originally transmitted image. Only a single copy of the transformed image need be retained by the transmitting device in order to satisfy requests for different amounts of image detail.

  3. Optoelectronic pH Meter: Further Details

    NASA Technical Reports Server (NTRS)

    Jeevarajan, Antony S.; Anderson, Mejody M.; Macatangay, Ariel V.

    2009-01-01

    A collection of documents provides further detailed information about an optoelectronic instrument that measures the pH of an aqueous cell-culture medium to within 0.1 unit in the range from 6.5 to 7.5. The instrument at an earlier stage of development was reported in Optoelectronic Instrument Monitors pH in a Culture Medium (MSC-23107), NASA Tech Briefs, Vol. 28, No. 9 (September 2004), page 4a. To recapitulate: The instrument includes a quartz cuvette through which the medium flows as it is circulated through a bioreactor. The medium contains some phenol red, which is an organic pH-indicator dye. The cuvette sits between a light source and a photodetector. [The light source in the earlier version comprised red (625 nm) and green (558 nm) light-emitting diodes (LEDs); the light source in the present version comprises a single green- (560 nm)-or-red (623 nm) LED.] The red and green are repeatedly flashed in alternation. The responses of the photodiode to the green and red are processed electronically to obtain the ratio between the amounts of green and red light transmitted through the medium. The optical absorbance of the phenol red in the green light varies as a known function of pH. Hence, the pH of the medium can be calculated from the aforesaid ratio.

  4. The ACPMAPS system: A detailed overview

    SciTech Connect

    Fischler, M.

    1992-07-01

    This paper describes the ACPMAPS computing system -- its purpose, its hardware architecture, how the system is used, and relevant programming paradigms and concepts. Features of the hardware and software will be discussed in some detail, both quantitative and qualitative. This should give some perspective as to the suitability of the ACPMAPS system for various classes of applications, and as to where this system stands in the spectrum of today`s supercomputers. The ACPMAPS project at Fermilab was initiated in 1987 as a collaborations between the Advanced Computer Program (now the Computer R&D department) and the lattice gauge physicists in the Theory department. ACPMAPS is an acronym for Advanced Computer Program Multiple Array Processor System -- this acronym is no longer accurate, but the name has stuck. Although research physics computations were done on ACPMAPS as early as 1989, the full-scale system was commissioned as a reliable physics tool in early 1991. The original ACPMAPS was a 5 Gflop (peak) system. An upgrade by a factor of ten in computer power and memory size, but substituting a new CPU board, will occur during early 1991 -- this is referred to as the new ACPMAPS Upgrade or 50 GF ACPMAPS. The appellation ACPMAPS II has also been applied to the upgrade; this is somewhat of a misnomer, since only one of five major components was changed.

  5. Detailed surveys of offshore Peru margin

    SciTech Connect

    Hussong, D.M.; Taylor, B.; Kulm, L.D.; Hilde, T.W.C.

    1986-07-01

    The complex and highly variable structure of the submarine continental margin of central Peru is revealed by geophysical surveys and geologic sampling completed in 1985. The surveys were conducted in preparation for deep scientific drilling to be undertaken by the Ocean Drilling Program in November-December 1986. More than 11,000 km/sup 2/ of sea floor were mapped using the SeaMARC II side-scan sonar and bathymetry system; 1500 km of multichannel seismic reflection profiles and 4000 km of single-channel seismic data were shot; and many coring, dredging, and heat-flow stations were obtained. The data permit construction of detailed three-dimensional geologic maps of the region. These maps show that the ancient metamorphic rocks of South America extend close to the trench axis and apparently have undergone a history of truncation and subsidence related to the subduction of the Nazca oceanic plate. Adjacent segments of the Peru forearc have dramatically different structure and appear to have had differing tectonic histories. The margin is disrupted by extensive (primarily tensional) faulting; the larger faults extend perpendicular to the strike of the trench and often serve as conduits for diapirs and mud volcanoes. Living chemosynthetic clams were dredged from 3800-m depth along one of these fault trends, suggesting that active fluid venting occurs at depth on the continental wall of the Peru Trench.

  6. Inverse sequential simulation: Performance and implementation details

    NASA Astrophysics Data System (ADS)

    Xu, Teng; Gómez-Hernández, J. Jaime

    2015-12-01

    For good groundwater flow and solute transport numerical modeling, it is important to characterize the formation properties. In this paper, we analyze the performance and important implementation details of a new approach for stochastic inverse modeling called inverse sequential simulation (iSS). This approach is capable of characterizing conductivity fields with heterogeneity patterns difficult to capture by standard multiGaussian-based inverse approaches. The method is based on the multivariate sequential simulation principle, but the covariances and cross-covariances used to compute the local conditional probability distributions are computed by simple co-kriging which are derived from an ensemble of conductivity and piezometric head fields, in a similar manner as the experimental covariances are computed in an ensemble Kalman filtering. A sensitivity analysis is performed on a synthetic aquifer regarding the number of members of the ensemble of realizations, the number of conditioning data, the number of piezometers at which piezometric heads are observed, and the number of nodes retained within the search neighborhood at the moment of computing the local conditional probabilities. The results show the importance of having a sufficiently large number of all of the mentioned parameters for the algorithm to characterize properly hydraulic conductivity fields with clear non-multiGaussian features.

  7. The ACPMAPS system: A detailed overview

    SciTech Connect

    Fischler, M.

    1992-01-01

    This paper describes the ACPMAPS computing system -- its purpose, its hardware architecture, how the system is used, and relevant programming paradigms and concepts. Features of the hardware and software will be discussed in some detail, both quantitative and qualitative. This should give some perspective as to the suitability of the ACPMAPS system for various classes of applications, and as to where this system stands in the spectrum of today's supercomputers. The ACPMAPS project at Fermilab was initiated in 1987 as a collaborations between the Advanced Computer Program (now the Computer R D department) and the lattice gauge physicists in the Theory department. ACPMAPS is an acronym for Advanced Computer Program Multiple Array Processor System -- this acronym is no longer accurate, but the name has stuck. Although research physics computations were done on ACPMAPS as early as 1989, the full-scale system was commissioned as a reliable physics tool in early 1991. The original ACPMAPS was a 5 Gflop (peak) system. An upgrade by a factor of ten in computer power and memory size, but substituting a new CPU board, will occur during early 1991 -- this is referred to as the new ACPMAPS Upgrade or 50 GF ACPMAPS. The appellation ACPMAPS II has also been applied to the upgrade; this is somewhat of a misnomer, since only one of five major components was changed.

  8. Detailed Chromospheric Activity Nature of KIC 9641031

    NASA Astrophysics Data System (ADS)

    Yoldaş, Ezgi; Dal, Hasan Ali

    2016-04-01

    This study depends on KIC 9641031 eclipsing binary with a chromospherically active component. There are three type variations, such as geometrical variations due to eclipses, sinusoidal variations due to the rotational modulations, and also flares, in the light curves. Taking into account results obtained from observations in the Kepler Mission Database, we discuss the details of chromospheric activity. The sinusoidal light variations due to rotational modulation and the flare events were modelled. 92 different data subsets separated using the analytic models were modelled separately to obtain the cool spot configuration. Acording to the model, there are two active regions separated by about 180° longitudinally between the latitudes of +50° and +100°. 240 flares, whose parameters were computed, were detected. Using these parameters, the OPEA model was derived, in which the Plateau value was found to be 1.232±0.069 s, and half-life parameter was found as 2291.7 s. The flare frequency N1 was found as 0.41632 h-1, while the flare frequency N2 was found as 0.00027. Considering these parameters together with the orbital period variations demonstrates that the period variations depend on chromospheric activity. Comparing the system with its analogue, the activity level of KIC 9641031 is remarkably lower than the others.

  9. Detailed sensory memory, sloppy working memory.

    PubMed

    Sligte, Ilja G; Vandenbroucke, Annelinde R E; Scholte, H Steven; Lamme, Victor A F

    2010-01-01

    Visual short-term memory (VSTM) enables us to actively maintain information in mind for a brief period of time after stimulus disappearance. According to recent studies, VSTM consists of three stages - iconic memory, fragile VSTM, and visual working memory - with increasingly stricter capacity limits and progressively longer lifetimes. Still, the resolution (or amount of visual detail) of each VSTM stage has remained unexplored and we test this in the present study. We presented people with a change detection task that measures the capacity of all three forms of VSTM, and we added an identification display after each change trial that required people to identify the "pre-change" object. Accurate change detection plus pre-change identification requires subjects to have a high-resolution representation of the "pre-change" object, whereas change detection or identification only can be based on the hunch that something has changed, without exactly knowing what was presented before. We observed that people maintained 6.1 objects in iconic memory, 4.6 objects in fragile VSTM, and 2.1 objects in visual working memory. Moreover, when people detected the change, they could also identify the pre-change object on 88% of the iconic memory trials, on 71% of the fragile VSTM trials and merely on 53% of the visual working memory trials. This suggests that people maintain many high-resolution representations in iconic memory and fragile VSTM, but only one high-resolution object representation in visual working memory. PMID:21897823

  10. Some articulatory details of emotional speech

    NASA Astrophysics Data System (ADS)

    Lee, Sungbok; Yildirim, Serdar; Bulut, Murtaza; Kazemzadeh, Abe; Narayanan, Shrikanth

    2005-09-01

    Differences in speech articulation among four emotion types, neutral, anger, sadness, and happiness are investigated by analyzing tongue tip, jaw, and lip movement data collected from one male and one female speaker of American English. The data were collected using an electromagnetic articulography (EMA) system while subjects produce simulated emotional speech. Pitch, root-mean-square (rms) energy and the first three formants were estimated for vowel segments. For both speakers, angry speech exhibited the largest rms energy and largest articulatory activity in terms of displacement range and movement speed. Happy speech is characterized by largest pitch variability. It has higher rms energy than neutral speech but articulatory activity is rather comparable to, or less than, neutral speech. That is, happy speech is more prominent in voicing activity than in articulation. Sad speech exhibits longest sentence duration and lower rms energy. However, its articulatory activity is no less than neutral speech. Interestingly, for the male speaker, articulation for vowels in sad speech is consistently more peripheral (i.e., more forwarded displacements) when compared to other emotions. However, this does not hold for female subject. These and other results will be discussed in detail with associated acoustics and perceived emotional qualities. [Work supported by NIH.

  11. Detailed Aerosol Characterization using Polarimetric Measurements

    NASA Astrophysics Data System (ADS)

    Hasekamp, Otto; di Noia, Antonio; Stap, Arjen; Rietjens, Jeroen; Smit, Martijn; van Harten, Gerard; Snik, Frans

    2016-04-01

    Anthropogenic aerosols are believed to cause the second most important anthropogenic forcing of climate change after greenhouse gases. In contrast to the climate effect of greenhouse gases, which is understood relatively well, the negative forcing (cooling effect) caused by aerosols represents the largest reported uncertainty in the most recent assessment of the International Panel on Climate Change (IPCC). To reduce the large uncertainty on the aerosol effects on cloud formation and climate, accurate satellite measurements of aerosol optical properties (optical thickness, single scattering albedo, phase function) and microphysical properties (size distribution, refractive index, shape) are essential. There is growing consensus in the aerosol remote sensing community that multi-angle measurements of intensity and polarization are essential to unambiguously determine all relevant aerosol properties. This presentations adresses the different aspects of polarimetric remote sensing of atmospheric aerosols, including retrieval algorithm development, validation, and data needs for climate and air quality applications. During past years, at SRON-Netherlands Instite for Space Research retrieval algorithms have been developed that make full use of the capabilities of polarimetric measurements. We will show results of detailed aerosol properties from ground-based- (groundSPEX), airborne- (NASA Research Scanning Polarimeter), and satellite (POLDER) measurements. Also we will discuss observational needs for future instrumentation in order to improve our understanding of the role of aerosols in climate change and air quality.

  12. Detailed Chemical Kinetic Modeling of Cyclohexane Oxidation

    SciTech Connect

    Silke, E J; Pitz, W J; Westbrook, C K; Ribaucour, M

    2006-11-10

    A detailed chemical kinetic mechanism has been developed and used to study the oxidation of cyclohexane at both low and high temperatures. Reaction rate constant rules are developed for the low temperature combustion of cyclohexane. These rules can be used for in chemical kinetic mechanisms for other cycloalkanes. Since cyclohexane produces only one type of cyclohexyl radical, much of the low temperature chemistry of cyclohexane is described in terms of one potential energy diagram showing the reaction of cyclohexyl radical + O{sub 2} through five, six and seven membered ring transition states. The direct elimination of cyclohexene and HO{sub 2} from RO{sub 2} is included in the treatment using a modified rate constant of Cavallotti et al. Published and unpublished data from the Lille rapid compression machine, as well as jet-stirred reactor data are used to validate the mechanism. The effect of heat loss is included in the simulations, an improvement on previous studies on cyclohexane. Calculations indicated that the production of 1,2-epoxycyclohexane observed in the experiments can not be simulated based on the current understanding of low temperature chemistry. Possible 'alternative' H-atom isomerizations leading to different products from the parent O{sub 2}QOOH radical were included in the low temperature chemical kinetic mechanism and were found to play a significant role.

  13. Details of tetrahedral anisotropic mesh adaptation

    NASA Astrophysics Data System (ADS)

    Jensen, Kristian Ejlebjerg; Gorman, Gerard

    2016-04-01

    We have implemented tetrahedral anisotropic mesh adaptation using the local operations of coarsening, swapping, refinement and smoothing in MATLAB without the use of any for- N loops, i.e. the script is fully vectorised. In the process of doing so, we have made three observations related to details of the implementation: 1. restricting refinement to a single edge split per element not only simplifies the code, it also improves mesh quality, 2. face to edge swapping is unnecessary, and 3. optimising for the Vassilevski functional tends to give a little higher value for the mean condition number functional than optimising for the condition number functional directly. These observations have been made for a uniform and a radial shock metric field, both starting from a structured mesh in a cube. Finally, we compare two coarsening techniques and demonstrate the importance of applying smoothing in the mesh adaptation loop. The results pertain to a unit cube geometry, but we also show the effect of corners and edges by applying the implementation in a spherical geometry.

  14. Detail-preserving construction of neonatal brain atlases in space-frequency domain.

    PubMed

    Zhang, Yuyao; Shi, Feng; Yap, Pew-Thian; Shen, Dinggang

    2016-06-01

    Brain atlases are commonly utilized in neuroimaging studies. However, most brain atlases are fuzzy and lack structural details, especially in the cortical regions. This is mainly caused by the image averaging process involved in atlas construction, which often smoothes out high-frequency contents that capture fine anatomical details. Brain atlas construction for neonatal images is even more challenging due to insufficient spatial resolution and low tissue contrast. In this paper, we propose a novel framework for detail-preserving construction of population-representative atlases. Our approach combines spatial and frequency information to better preserve image details. This is achieved by performing atlas construction in the space-frequency domain given by wavelet transform. In particular, sparse patch-based atlas construction is performed in all frequency subbands, and the results are combined to give a final atlas. For enhancing anatomical details, tissue probability maps are also used to guide atlas construction. Experimental results show that our approach can produce atlases with greater structural details than existing atlases. Hum Brain Mapp 37:2133-2150, 2016. © 2016 Wiley Periodicals, Inc. PMID:26987787

  15. Detailed slab and mantle structure beneath westernmost Mediterranean

    NASA Astrophysics Data System (ADS)

    Sun, D.; Miller, M. S.; Bezada, M. J.; Humphreys, E.

    2013-12-01

    The geological evolution of the westernmost Mediterranean holds an important piece of the puzzle of how whole western Mediterranean evolved due to the convergence of Africa with Eurasia. Detailed upper mantle seismological images are crucial to test two controversial ideas about the dynamic process of the westernmost Mediterranean during the Cenozoic: slab rollback and lithosphere delamination. Recent tomographic images based on the dense seismic network in Spain and northern Morocco reveal a high-resolution continuous high-velocity anomaly to the transition zone depth under the Alboran domain [Bezada and Humphreys, 2013], which was used to support the slab roll back hypothesis for the westernmost Mediterranean tectonic evolution. However, the slab shape, width, and sharpness of its edges are not well resolved. Furthermore, the deep 2010 earthquake beneath Granada, Spain suggests possible oceanic crust material existing at ~ 600 km depth, which cannot be resolved by current tomography models. The study of multipathing and waveform broadening around sharp features has proven an efficient way to study those features. Here, we use both P and S waveform data from the PICASSO array to produce a detailed image. For the deep Granada earthquake, high frequency second arrivals and long coda after the P and S arrivals are shown on stations in the Rif Mountains of Morocco. By fitting both SH and P waveform data, we suggest that a low-velocity layer (LVL, 2 km thickness, δVs = -10%), possibly old oceanic crust, sits on top of the slab. The seismic waves travel through the LVL as guided waves preserving their high frequency energy. The strength of the second arrivals are very sensitive to the relative location between the deep earthquake and the LVL, which indicates the 2010 deep earthquake was most-likely within the subducted oceanic crust. Using both teleseismic and regional data, we conclude that the width of the sub-vertical slab is ~150 km, which is sharper than the

  16. Ancillary-service details: Dynamic scheduling

    SciTech Connect

    Hirst, E.; Kirby, B.

    1997-01-01

    Dynamic scheduling (DS) is the electronic transfer from one control area to another of the time-varying electricity consumption associated with a load or the time-varying electricity production associated with a generator. Although electric utilities have been using this technique for at least two decades, its use is growing in popularity and importance. This growth is a consequence of the major changes under way in US bulk-power markets, in particular efforts to unbundle generation from transmission and to increase competition among generation providers. DS can promote competition and increase choices. It allows consumers to purchase certain services from entities outside their physical-host area and it allows generators to sell certain services to entities other than their physical host. These services include regulation (following minute-to-minute variations in load) and operating reserves, among others. Such an increase in the number of possible suppliers and customers should encourage innovation and reduce the costs and prices of providing electricity services. The purpose of the project reported here was to collect and analyze data on utility experiences with DS. Chapter 2 provides additional details and examples of the definitions of DS. Chapter 3 explains why DS might be an attractive service that customers and generators, as well as transmission providers, might wan to use. Chapter 4 presents some of the many current DS examples the authors uncovered in their interviews. Chapter 5 discusses the costs and cost-effectiveness of DS. Chapter 6 explains what they believe can and cannot be electronically moved from one control area to another, primarily in terms of the six ancillary services that FERC defined in Order 888. Chapter 7 discusses the need for additional research on DS.

  17. Detailed modelling of the 21-cm forest

    NASA Astrophysics Data System (ADS)

    Semelin, B.

    2016-01-01

    The 21-cm forest is a promising probe of the Epoch of Reionization. The local state of the intergalactic medium (IGM) is encoded in the spectrum of a background source (radio-loud quasars or gamma-ray burst afterglow) by absorption at the local 21-cm wavelength, resulting in a continuous and fluctuating absorption level. Small-scale structures (filaments and minihaloes) in the IGM are responsible for the strongest absorption features. The absorption can also be modulated on large scales by inhomogeneous heating and Wouthuysen-Field coupling. We present the results from a simulation that attempts to preserve the cosmological environment while resolving some of the small-scale structures (a few kpc resolution in a 50 h-1 Mpc box). The simulation couples the dynamics and the ionizing radiative transfer and includes X-ray and Lyman lines radiative transfer for a detailed physical modelling. As a result we find that soft X-ray self-shielding, Ly α self-shielding and shock heating all have an impact on the predicted values of the 21-cm optical depth of moderately overdense structures like filaments. A correct treatment of the peculiar velocities is also critical. Modelling these processes seems necessary for accurate predictions and can be done only at high enough resolution. As a result, based on our fiducial model, we estimate that LOFAR should be able to detect a few (strong) absorptions features in a frequency range of a few tens of MHz for a 20 mJy source located at z = 10, while the SKA would extract a large fraction of the absorption information for the same source.

  18. Rhinoscleroma: a detailed histopathological diagnostic insight

    PubMed Central

    Ahmed, Ahmed RH; El-badawy, Zeinab H; Mohamed, Ibrahim R; Abdelhameed, Waleed AM

    2015-01-01

    Rhinoscleroma (RS) is a chronic specific disease of nose and upper respiratory passages caused by Klebsiella rhinoscleromatis bacilli. It is endemic in Egypt and in sporadic areas worldwide. Diagnosis of RS depends on identification of the pathognomonic Mickulicz cells (MCs) which is most prominent during granulomatous phase but spares or absent during catarrhal or sclerotic phases of the disease. This study aimed to identify the potential diagnostic features of nasal RS when MCs are absent. Nasal biopsies from 125 patients complaining of chronic nasal symptoms were retrieved for this study; including 72 chronic non specific inflammatory lesions and 53 RS diagnosed by PAS and Geimsa stains. The detailed histological differences among the two groups were measured statistically. RS was frequently a bilateral disease (P < 0.05) of young age (P < 0.001) with a female predominance (P < 0.05) and usually associated with nasal crustations (P < 0.001). Five strong histological indicators of RS were specified by univariate binary logistic regression analyses including squamous metaplasia (OR 27.2, P < 0.0001), dominance of plasma cells (OR 12.75, P < 0.0001), Russell bodies (OR 8.83, P < 0.0001), neutrophiles (OR 3.7, P < 0.001) and absence of oesinophiles (OR 12.0, P < 0.0001). According to Multivariate analysis, the diagnostic features of RS in absence of MCs can be classified into major criteria including dominance of plasma cells infiltration and absence of oesinophiles and minor criteria including young age, female gender, bilateral nasal involvement, nasal crustation, squamous metaplasia, Russell bodies, and neutrophiles. The diagnostic model using the two major criteria confirmed or excluded RS in 84.3% of the investigated cases. PMID:26339415

  19. Chord, Horizontal Tie Bar & Crossbracing Joint Details; Crossbracing Center ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Chord, Horizontal Tie Bar & Crossbracing Joint Details; Crossbracing Center Joint Detail; Chord, Panel Posts, Braces & Counterbrace Joint Detail - Brownsville Covered Bridge, Spanning East Fork Whitewater River (moved to Eagle Creek Park, Indianapolis), Brownsville, Union County, IN

  20. 5 CFR 352.305 - Eligibility for detail.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... RIGHTS Detail and Transfer of Federal Employees to International Organizations § 352.305 Eligibility for detail. An employee is eligible for detail to an international organization with the rights provided...

  1. Brown Dwarfs: Discovery and Detailed Studies

    NASA Technical Reports Server (NTRS)

    Kulkarni, Shrinivas R.

    2001-01-01

    We obtained the optical and IR spectra of Gliese 229B and identified Cs, I, and CO features - as expected in theoretical models. Our optical IR spectrum showed that most of the refractory metals have condensed out of the atmosphere and the presence of Cs, I and CO shows evidence for disequilibrium chemistry. We reported orbital evidence for Gliese 229B. The HST measured optical magnitudes provide additional evidence for the absence of dust in the atmosphere of this cool object. The luminosity of brown dwarfs depend on their masses and ages and in order to interpret the results of the survey we have carried out an extensive Monte Carlo analysis. Our conclusion is that warm brown dwarfs are rare, as companions in the orbital period range beyond approximately 30 - 50 AU. The Palomer survey poses no constraint for brown dwarfs in planetary orbits similar to those of the outer planets. We have just started a program of imaging nearby stars with the newly commissioned AO system at Palomar and Keck and have already found a brown dwarf candidate.

  2. 11. Exterior detail view of northeast corner, showing stucco finish ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    11. Exterior detail view of northeast corner, showing stucco finish and woodwork details - American Railway Express Company Freight Building, 1060 Northeast Division Street, Bend, Deschutes County, OR

  3. Image Viewer using Digital Imaging and Communications in Medicine (DICOM)

    NASA Astrophysics Data System (ADS)

    Baraskar, Trupti N.

    2010-11-01

    Digital Imaging and Communications in Medicine is a standard for handling, storing, printing, and transmitting information in medical imaging. The National Electrical Manufacturers Association holds the copyright to this standard. It was developed by the DICOM Standards committee. The other image viewers cannot collectively store the image details as well as the patient's information. So the image may get separated from the details, but DICOM file format stores the patient's information and the image details. Main objective is to develop a DICOM image viewer. The image viewer will open .dcm i.e. DICOM image file and also will have additional features such as zoom in, zoom out, black and white inverter, magnifier, blur, B/W inverter, horizontal and vertical flipping, sharpening, contrast, brightness and .gif converter are incorporated.

  4. Magnetic resonance imaging

    SciTech Connect

    Elster, A.D.

    1986-01-01

    The author succeeds in making the physical phenomena of MR imaging quite comprehensible. The chapters on imaging sequences and parameters and the effects of pathologic conditions on MR images are written in a way that helps the beginner. MR artifacts are discussed in a special chapter. The atlas, which makes up 60% of the book; includes a detailed imaging guide with protocols concentrating mainly on the head, neck and brain. MR imaging of the chest is discussed as well as abdomen, pelvis and hips, and the spine, breast, and knee. The book ends with a list of MR equipment manufacturers, specifications of nine major commercial MR imagers, and a glossary of MR terminology.

  5. Head CT (image)

    MedlinePlus

    CT stands for computerized tomography. In this procedure, a thin X-ray beam is rotated around the ... D image of a section through the body. CT scans are very detailed and provide excellent information ...

  6. CT scan (image)

    MedlinePlus

    CT stands for computerized tomography. In this procedure, a thin X-ray beam is rotated around the ... D image of a section through the body. CT scans are very detailed and provide excellent information ...

  7. Space-Frequency Detail-Preserving Construction of Neonatal Brain Atlases

    PubMed Central

    Zhang, Yuyao; Shi, Feng; Yap, Pew-Thian; Shen, Dinggang

    2016-01-01

    Brain atlases are an integral component of neuroimaging studies. However, most brain atlases are fuzzy and lack structural details, especially in the cortical regions. In particular, neonatal brain atlases are especially challenging to construct due to the low spatial resolution and low tissue contrast. This is mainly caused by the image averaging process involved in atlas construction, often smoothing out high-frequency contents that indicate fine anatomical details. In this paper, we propose a novel framework for detail-preserving construction of atlases. Our approach combines space and frequency information to better preserve image details. This is achieved by performing reconstruction in the space-frequency domain given by wavelet transform. Sparse patch-based atlas reconstruction is performed in each frequency subband. Combining the results for all these subbands will then result in a refined atlas. Compared with existing atlases, experimental results indicate that our approach has the ability to build an atlas with more structural details, thus leading to better performance when used to normalize a group of testing neonatal images. PMID:27169138

  8. Panel Post & Diagonal Brace Joint Detail; Crossbracing Center Joint ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Panel Post & Diagonal Brace Joint Detail; Crossbracing Center Joint Detail; Chord, Panel Post, Tie Bar, & Diagonal Brace Joint Detail; Chord, Tie Bar, & Crossbracing Joint Detail - Medora Bridge, Spanning East Fork of White River at State Route 235, Medora, Jackson County, IN

  9. 5 CFR 2635.104 - Applicability to employees on detail.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false Applicability to employees on detail... Applicability to employees on detail. (a) Details to other agencies. Except as provided in paragraph (d) of this section, an employee on detail, including a uniformed officer on assignment, from his employing agency...

  10. 5 CFR 930.106 - Details in the competitive service.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Details in the competitive service. 930... Operators § 930.106 Details in the competitive service. An agency may detail an employee to an operator... details exceeding 30 days, the employee must meet all the requirements of § 930.105 and any applicable...

  11. Detail-Preserving and Content-Aware Variational Multi-View Stereo Reconstruction.

    PubMed

    Li, Zhaoxin; Wang, Kuanquan; Zuo, Wangmeng; Meng, Deyu; Zhang, Lei

    2016-02-01

    Accurate recovery of 3D geometrical surfaces from calibrated 2D multi-view images is a fundamental yet active research area in computer vision. Despite the steady progress in multi-view stereo (MVS) reconstruction, many existing methods are still limited in recovering fine-scale details and sharp features while suppressing noises, and may fail in reconstructing regions with less textures. To address these limitations, this paper presents a detail-preserving and content-aware variational (DCV) MVS method, which reconstructs the 3D surface by alternating between reprojection error minimization and mesh denoising. In reprojection error minimization, we propose a novel inter-image similarity measure, which is effective to preserve fine-scale details of the reconstructed surface and builds a connection between guided image filtering and image registration. In mesh denoising, we propose a content-aware ℓp-minimization algorithm by adaptively estimating the p value and regularization parameters. Compared with conventional isotropic mesh smoothing approaches, the proposed method is much more promising in suppressing noise while preserving sharp features. Experimental results on benchmark data sets demonstrate that our DCV method is capable of recovering more surface details, and obtains cleaner and more accurate reconstructions than the state-of-the-art methods. In particular, our method achieves the best results among all published methods on the Middlebury dino ring and dino sparse data sets in terms of both completeness and accuracy. PMID:26672037

  12. Detail-Preserving and Content-Aware Variational Multi-View Stereo Reconstruction

    NASA Astrophysics Data System (ADS)

    Li, Zhaoxin; Wang, Kuanquan; Zuo, Wangmeng; Meng, Deyu; Zhang, Lei

    2016-02-01

    Accurate recovery of 3D geometrical surfaces from calibrated 2D multi-view images is a fundamental yet active research area in computer vision. Despite the steady progress in multi-view stereo reconstruction, most existing methods are still limited in recovering fine-scale details and sharp features while suppressing noises, and may fail in reconstructing regions with few textures. To address these limitations, this paper presents a Detail-preserving and Content-aware Variational (DCV) multi-view stereo method, which reconstructs the 3D surface by alternating between reprojection error minimization and mesh denoising. In reprojection error minimization, we propose a novel inter-image similarity measure, which is effective to preserve fine-scale details of the reconstructed surface and builds a connection between guided image filtering and image registration. In mesh denoising, we propose a content-aware $\\ell_{p}$-minimization algorithm by adaptively estimating the $p$ value and regularization parameters based on the current input. It is much more promising in suppressing noise while preserving sharp features than conventional isotropic mesh smoothing. Experimental results on benchmark datasets demonstrate that our DCV method is capable of recovering more surface details, and obtains cleaner and more accurate reconstructions than state-of-the-art methods. In particular, our method achieves the best results among all published methods on the Middlebury dino ring and dino sparse ring datasets in terms of both completeness and accuracy.

  13. Conceptual Distinctiveness Supports Detailed Visual Long-Term Memory for Real-World Objects

    ERIC Educational Resources Information Center

    Konkle, Talia; Brady, Timothy F.; Alvarez, George A.; Oliva, Aude

    2010-01-01

    Humans have a massive capacity to store detailed information in visual long-term memory. The present studies explored the fidelity of these visual long-term memory representations and examined how conceptual and perceptual features of object categories support this capacity. Observers viewed 2,800 object images with a different number of exemplars…

  14. Impregnating unconsolidated pyroclastic sequences: A tool for detailed facies analysis

    NASA Astrophysics Data System (ADS)

    Klapper, Daniel; Kueppers, Ulrich; Castro, Jon M.; Pacheco, Jose M. R.; Dingwell, Donald B.

    2010-05-01

    -size distribution, componentry, and grain morphology in situ in a 2D-plane. In a first step, the sample surface has been scanned and analysed by means of image analysis software (Image J). After that, selected areas were investigated through thin section analysis. We were able to define depositional units in the (sub)-mm scale and the show the varying relative importance of 1) eruptive style, 2) transportation mode, and 3) the influence of wind and (air) humidity. The presented method is an easy and efficient tool for a detailed stratigraphic investigation of unconsolidated pyroclastic units.

  15. Impregnating unconsolidated pyroclastic sequences: A tool for detailed facies analysis

    NASA Astrophysics Data System (ADS)

    Klapper, D.; Kueppers, U.; Castro, J. M.

    2009-12-01

    -size distribution, componentry, and grain morphology in situ in a 2D-plane. In a first step, the sample surface has been scanned and analysed by means of image analysis software (Image J). After that, selected areas were investigated through thin section analysis. We were able to define depositional units in the (sub)-mm scale and the show the varying relative importance of 1) eruptive style, 2) transportation mode, and 3) the influence of wind and (air) humidity. The presented method is an easy and efficient tool for a detailed stratigraphic investigation of unconsolidated pyroclastic units.

  16. Detailed Design of the Heliophysics Event Knowledgebase (HEK)

    NASA Astrophysics Data System (ADS)

    Somani, Ankur; Seguin, R.; Timmons, R.; Freeland, S.; Hurlburt, N.; Kobashi, A.; Jaffey, A.

    2010-05-01

    We present the Heliophysics Event Registry (HER) and the Heliophysics Coverage Registry (HCR), which serve as two components of the Heliophysics Event Knowledgebase (HEK). Using standardized XML formats built upon the IVOA VOEvent specification, events can be ingested, stored, and later searched upon. Various web services and SolarSoft routines are available to aid in these functions. One source of events for the HEK is an automated Event Detection System (EDS) that continuously runs feature finding modules on SDO data. Modules are primarily supplied by the Smithsonian Astrophysical Observatory-led Feature Finding Team. The distributed system will keep up with SDO's data rate and issue space weather alerts in near-real time. Some modules will be run on all data while others are run in response to certain solar phenomena found by other modules in the system. Panorama is a software tool used for rapid visualization of large volumes of solar image data in multiple channels/wavelengths. With the EVACS front-end GUI tool, Panorama allows the user to, in real-time, change channel pixel scaling, weights, alignment, blending and colorization of the data. The user can also easily create WYSIWYG movies and launch the Annotator tool to describe events and features the user observes in the data. Panorama can also be used to drive clustered HiperSpace walls using the CGLX toolkit. The Event Viewer and Control Software (EVACS) provides a GUI that the user can search both the HER and HCR with. By specifying a start and end time and selecting the types of events and instruments that are of interest, EVACS will display the events on a full disk image of the sun while displaying more detailed information for the events. As mentioned, the user can also launch Panorama via EVACS.

  17. Contrast-detail evaluation and dose assessment of eight digital chest radiography systems in clinical practice.

    PubMed

    Veldkamp, Wouter J H; Kroft, Lucia J M; Boot, Mireille V; Mertens, Bart J A; Geleijns, Jacob

    2006-02-01

    The purpose of this study was to assess contrast-detail performance and effective dose of eight different digital chest radiography systems. Digital chest radiography systems from different manufacturers were included: one storage phosphor system, one selenium-coated drum system, and six direct readout systems including four thin-film transistor (TFT) systems and two charge-coupled device (CCD) systems. For measuring image quality, a contrast-detail test object was used in combination with a phantom that simulates the primary and scatter transmission through lung fields (LucAl). Six observers judged phantom images of each modality by soft-copy reading in a four-alternative-forced-choice experiment. The entrance dose was also measured, and the effective dose was calculated for an average patient. Contrast-detail curves were constructed from the observer data. The blocked two-way ANOVA test was used for statistical analysis. Significant difference in contrast-detail performance was found between the systems. Best contrast-detail performance was shown by a CCD system with slot-scan technology, and the selenium-coated drum system was compared to the other six systems (p values detail performance and effective dose levels were found between different digital chest radiography systems in clinical practice. PMID:16132918

  18. Visualized numerical assessment for near infrared diffuse optical tomography with contrast-and-size detail analysis

    NASA Astrophysics Data System (ADS)

    Chen, Liang-Yu; Pan, Min-Cheng; Pan, Min-Chun

    2013-01-01

    The purpose of this study is to propose an objective contrast-and-size detail (CSD) analysis for near infrared diffuse optical tomography (NIR DOT), of which the concept is derived from the subjective contrast detail (CD) analysis. We define a measure for numerical CSD analysis based on the resolution estimation of contrast and size. Following that, the contrast-and-size map of resolution can be calculated and displayed for each corresponding image in the map; furthermore, a CSD resolution curve can be plotted by calculating the average value of the projection corresponding to the physical quantity/axis (size or contrast). To provide some worked examples about the proposed CSD analysis evaluating the imaging performance of different reconstruction methods, Tikhonov regularization and edge-preserving regularization with different weighting functions were employed. Results suggested that using edge-preserving regularization with the generalized Lorentzian weighting function is the most attractive for the estimation of absorption-coefficient images.

  19. Introducing DeBRa: a detailed breast model for radiological studies

    NASA Astrophysics Data System (ADS)

    Ma, Andy K. W.; Gunn, Spencer; Darambara, Dimitra G.

    2009-07-01

    Currently, x-ray mammography is the method of choice in breast cancer screening programmes. As the mammography technology moves from 2D imaging modalities to 3D, conventional computational phantoms do not have sufficient detail to support the studies of these advanced imaging systems. Studies of these 3D imaging systems call for a realistic and sophisticated computational model of the breast. DeBRa (Detailed Breast model for Radiological studies) is the most advanced, detailed, 3D computational model of the breast developed recently for breast imaging studies. A DeBRa phantom can be constructed to model a compressed breast, as in film/screen, digital mammography and digital breast tomosynthesis studies, or a non-compressed breast as in positron emission mammography and breast CT studies. Both the cranial-caudal and mediolateral oblique views can be modelled. The anatomical details inside the phantom include the lactiferous duct system, the Cooper ligaments and the pectoral muscle. The fibroglandular tissues are also modelled realistically. In addition, abnormalities such as microcalcifications, irregular tumours and spiculated tumours are inserted into the phantom. Existing sophisticated breast models require specialized simulation codes. Unlike its predecessors, DeBRa has elemental compositions and densities incorporated into its voxels including those of the explicitly modelled anatomical structures and the noise-like fibroglandular tissues. The voxel dimensions are specified as needed by any study and the microcalcifications are embedded into the voxels so that the microcalcification sizes are not limited by the voxel dimensions. Therefore, DeBRa works with general-purpose Monte Carlo codes. Furthermore, general-purpose Monte Carlo codes allow different types of imaging modalities and detector characteristics to be simulated with ease. DeBRa is a versatile and multipurpose model specifically designed for both x-ray and γ-ray imaging studies.

  20. SeaWinds Global Coverage with Detail of Hurricane Floyd

    NASA Technical Reports Server (NTRS)

    1999-01-01

    The distribution of ocean surface winds over the Atlantic Ocean, based on September 1999 data from NASA's SeaWinds instrument on the QuikScat satellite, shows wind direction (white streamlines) at a resolution of 25 kilometers (15.5 miles), superimposed on the color image indicating wind speed.

    Over the ocean, the strong (seen in violet) trade winds blow steadily from the cooler subtropical oceans to warm waters just north of the equator. The air rises over these warm waters and sinks in the subtropics at the horse latitudes. Low wind speeds are indicated in blue. In the mid-latitudes, the high vorticity caused by the rotation of the Earth generates the spirals of weather systems. The North Atlantic is dominated by a high-pressure system, whose anti-cyclonic (clockwise) flow creates strong winds blowing parallel to the coast of Spain and Morocco. This creates strong ocean upwelling and cold temperature. Hurricane Floyd, with its high winds (yellow), is clearly visible west of the Bahamas. Tropical depression Gert is seen as it was forming in the tropical mid-Atlantic (as an anti-clockwise spiral); it later developed into a full-blown hurricane.

    Because the atmosphere is largely transparent to microwaves, SeaWinds is able to cover 93 percent of the global oceans, under both clear and cloudy conditions, in a single day, with the capability of a synoptic view of the ocean. The high resolution of the data also gives detailed description of small and intense weather systems, like Hurricane Floyd. The image in the insert is based on data specially produced at 12.5 kilometers (7.7 miles). In the insert, white arrows of wind vector are imposed on the color image of wind speed. The insert represents a 3-degree area occupied by Hurricane Floyd. After these data were acquired, Hurricane Floyd turned north. Its strength and proximity to the Atlantic coast of the U.S. caused the largest evacuation of citizens in U.S. history. Its landfall on September 16, 1999

  1. Evaluation of a software package for automated quality assessment of contrast detail images—comparison with subjective visual assessment

    NASA Astrophysics Data System (ADS)

    Pascoal, A.; Lawinski, C. P.; Honey, I.; Blake, P.

    2005-12-01

    Contrast detail analysis is commonly used to assess image quality (IQ) associated with diagnostic imaging systems. Applications include routine assessment of equipment performance and optimization studies. Most frequently, the evaluation of contrast detail images involves human observers visually detecting the threshold contrast detail combinations in the image. However, the subjective nature of human perception and the variations in the decision threshold pose limits to the minimum image quality variations detectable with reliability. Objective methods of assessment of image quality such as automated scoring have the potential to overcome the above limitations. A software package (CDRAD analyser) developed for automated scoring of images produced with the CDRAD test object was evaluated. Its performance to assess absolute and relative IQ was compared with that of an average observer. Results show that the software does not mimic the absolute performance of the average observer. The software proved more sensitive and was able to detect smaller low-contrast variations. The observer's performance was superior to the software's in the detection of smaller details. Both scoring methods showed frequent agreement in the detection of image quality variations resulting from changes in kVp and KERMAdetector, which indicates the potential to use the software CDRAD analyser for assessment of relative IQ.

  2. Magnetic resonance imaging

    SciTech Connect

    Stark, D.D.; Bradley, W.G. Jr.

    1988-01-01

    The authors present a review of magnetic resonance imaging. Many topics are explored from instrumentation, spectroscopy, blood flow and sodium imaging to detailed clinical applications such as the differential diagnosis of multiple sclerosis or adrenal adenoma. The emphasis throughout is on descriptions of normal multiplanar anatomy and pathology as displayed by MRI.

  3. Efficient eco-friendly inverted quantum dot sensitized solar cells† †Electronic supplementary information (ESI) available: TEM images of QDs, XPS spectra, UV-vis and PL spectra of the sensitized electrodes, details about photophysical characterization and IPCE spectra interpretation. See DOI: 10.1039/c5ta06769c Click here for additional data file.

    PubMed Central

    Park, Jinhyung; Sajjad, Muhammad T.; Jouneau, Pierre-Henri; Ruseckas, Arvydas; Faure-Vincent, Jérôme; Reiss, Peter

    2016-01-01

    Recent progress in quantum dot (QD) sensitized solar cells has demonstrated the possibility of low-cost and efficient photovoltaics. However, the standard device structure based on n-type materials often suffers from slow hole injection rate, which may lead to unbalanced charge transport. We have fabricated efficient p-type (inverted) QD sensitized cells, which combine the advantages of conventional QD cells with p-type dye sensitized configurations. Moreover, p-type QD sensitized cells can be used in highly promising tandem configurations with n-type ones. QDs without toxic Cd and Pb elements and with improved absorption and stability were successfully deposited onto mesoporous NiO electrode showing good coverage and penetration according to morphological analysis. Detailed photophysical charge transfer studies showed that high hole injection rates (108 s–1) observed in such systems are comparable with electron injection in conventional n-type QD assemblies. Inverted solar cells fabricated with various QDs demonstrate excellent power conversion efficiencies of up to 1.25%, which is 4 times higher than the best values for previous inverted QD sensitized cells. Attempts to passivate the surface of the QDs show that traditional methods of reduction of recombination in the QD sensitized cells are not applicable to the inverted architectures. PMID:27478616

  4. Stellar Imager

    NASA Technical Reports Server (NTRS)

    Carpenter, Kenneth

    2007-01-01

    The Stellar Imager (SI) is one of NASA's "Vision Missions" - concepts for future, space-based, strategic missions that could enormously increase our capabilities for observing the Cosmos. SI is designed as a UV/Optical Interferometer which will enable 0.1 milli-arcsecond (mas) spectral imaging of stellar surfaces and, via asteroseismology, stellar interiors and of the Universe in general. The ultra-sharp images of the Stellar Imager will revolutionize our view of many dynamic astrophysical processes by transforming point sources into extended sources, and snapshots into evolving views. SI, with a characteristic angular resolution of 0.1 milli-arcseconds at 2000 Angstroms, represents an advance in image detail of several hundred times over that provided by the Hubble Space Telescope. The Stellar Imager will zoom in on what today-with few exceptions - we only know as point sources, revealing processes never before seen, thus providing a tool as fundamental to astrophysics as the microscope is to the study of life on Earth. SI's science focuses on the role of magnetism in the Universe, particularly on magnetic activity on the surfaces of stars like the Sun. It's prime goal is to enable long-term forecasting of solar activity and the space weather that it drives, in support of the Living With a Star program in the Exploration Era. SI will also revolutionize our understanding of the formation of planetary systems, of the habitability and climatology of distant planets, and of many magneto-hydrodynamically controlled processes in the Universe. Stellar Imager is included as a "Flagship and Landmark Discovery Mission" in the 2005 Sun Solar System Connection (SSSC) Roadmap and as a candidate for a "Pathways to Life Observatory" in the Exploration of the Universe Division (EUD) Roadmap (May, 2005) and as such is a candidate mission for the 2025-2030 timeframe. An artist's drawing of the current "baseline" concept for SI is presented.

  5. 18. DETAIL OF SHAFT COLLAR AND CAGE GUIDES. VIEW LOOKING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    18. DETAIL OF SHAFT COLLAR AND CAGE GUIDES. VIEW LOOKING SOUTH INCLUDES DETAIL OF RIVETED STEEL CONSTRUCTION OF HEADFRAME. - Butte Mineyards, Stewart Mine, Intersection of Main & Woolman Streets, Butte, Silver Bow County, MT

  6. Photocopy of "sheet 4 of 8" showing window details, door ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Photocopy of "sheet 4 of 8" showing window details, door sill detail, vertical wall sections, and cross sections thru front, side and rear elevations. - Badger Mountain Lookout, .125 mile northwest of Badger Mountain summit, East Wenatchee, Douglas County, WA

  7. 9. South abutment, detail of collapsed east wing wall; also ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    9. South abutment, detail of collapsed east wing wall; also detail of bottom lateral bracing and stringers; looking southeast - Dodd Ford Bridge, County Road 147 Spanning Blue Earth River, Amboy, Blue Earth County, MN

  8. 3. East side, details of north half of east web; ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. East side, details of north half of east web; also details of roadway, railing and overhead bracing; looking northeast - Dodd Ford Bridge, County Road 147 Spanning Blue Earth River, Amboy, Blue Earth County, MN

  9. PHOTOCOPY OF A 1942 ARCHITECTURAL DRAWING TITLED: "STANDARD DETAILS. DOOR ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    PHOTOCOPY OF A 1942 ARCHITECTURAL DRAWING TITLED: "STANDARD DETAILS. DOOR TYPES & DETAILS." OCTOBER 31, 1942. - Madigan Hospital, Standard & Combination Wards, Bounded by Wilson & McKinley Avenues & Garfield & Lincoln Streets, Tacoma, Pierce County, WA

  10. PHOTOCOPY OF A 1942 ARCHITECTURAL DRAWING TITLED: "STANDARD DETAILS, SOLARIUM ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    PHOTOCOPY OF A 1942 ARCHITECTURAL DRAWING TITLED: "STANDARD DETAILS, SOLARIUM DETAILS." OCTOBER 31, 1942. - Madigan Hospital, Standard & Combination Wards, Bounded by Wilson & McKinley Avenues & Garfield & Lincoln Streets, Tacoma, Pierce County, WA

  11. 23. DETAILS, INCLUDING PIER PLAN AND SECTION AND PLACEMENT OF ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    23. DETAILS, INCLUDING PIER PLAN AND SECTION AND PLACEMENT OF REINFORCING STEEL, DETAIL OF RAILING, FLOOR SYSTEM REINFORCEMENT. February 4, 1922 - Chili Bar Bridge, Spanning South Fork of American River at State Highway 193, Placerville, El Dorado County, CA

  12. Lock 1 (Savannah River Lock), Elevation of North Wall, Detail ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Lock 1 (Savannah River Lock), Elevation of North Wall, Detail of Wall Foundation, Detail of Gate Pocket - Savannah & Ogeechee Barge Canal, Between Ogeechee & Savannah Rivers, Savannah, Chatham County, GA

  13. 9. VIEW TO NORTHEAST. DETAIL, OBLIQUE VIEW OF WEST APPROACH ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    9. VIEW TO NORTHEAST. DETAIL, OBLIQUE VIEW OF WEST APPROACH SPAN. NOTE PIN CONNECTIONS, UNDERSIDE DETAILS, SHADOW PATTERN CAST BY STEEL OPEN GRATE DECK. - Gianella Bridge, Spanning Sacramento River at State Highway 32, Hamilton City, Glenn County, CA

  14. 6. HOUSE NO. 2. DETAIL AT EAST END OF FRONT ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    6. HOUSE NO. 2. DETAIL AT EAST END OF FRONT SHOWING SIDING AND ROOF-WALL JUNCTURE DETAILS. VIEW TO SOUTHWEST. - Holter Hydroelectric Facility, House No. 2, End of Holter Dam Road, Wolf Creek, Lewis and Clark County, MT

  15. 3. Detail of north loading dock area showing column, insulated ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. Detail of north loading dock area showing column, insulated doors, and detail of underside of canopy - Fort Hood, World War II Temporary Buildings, Cold Storage Building, Seventeenth Street, Killeen, Bell County, TX

  16. Morning view, brick post detail; view also shows dimensional wallconstruction ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Morning view, brick post detail; view also shows dimensional wall-construction detail. North wall, with the camera facing northwest. - Beaufort National Cemetery, Wall, 1601 Boundary Street, Beaufort, Beaufort County, SC

  17. Introduction: Imaging in reproduction.

    PubMed

    Sella, Tamar; Laufer, Neri

    2016-06-01

    The authors of this Views and Reviews outline in detail the indispensable role of imaging tools-ultrasound, computed tomography, and magnetic resonance imaging-in the diagnosis and treatment of female and male factor infertility. Equipment producing diagnostic images, coupled with ever-increasing computing power, will pave the way for novel functional dynamic studies that will expand the understanding of reproductive processes and their management. PMID:27117374

  18. Apple Image Processing Educator

    NASA Technical Reports Server (NTRS)

    Gunther, F. J.

    1981-01-01

    A software system design is proposed and demonstrated with pilot-project software. The system permits the Apple II microcomputer to be used for personalized computer-assisted instruction in the digital image processing of LANDSAT images. The programs provide data input, menu selection, graphic and hard-copy displays, and both general and detailed instructions. The pilot-project results are considered to be successful indicators of the capabilities and limits of microcomputers for digital image processing education.

  19. First-Generation Hybrid Compact Compton Imager

    SciTech Connect

    Cunningham, M; Burks, M; Chivers, D; Cork, C; Fabris, L; Gunter, D; Krings, T; Lange, D; Hull, E; Mihailescu, L; Nelson, K; Niedermayr, T; Protic, D; Valentine, J; Vetter, K; Wright, D

    2005-11-07

    At Lawrence Livermore National Laboratory, we are pursuing the development of a gamma-ray imaging system using the Compton effect. We have built our first generation hybrid Compton imaging system, and we have conducted initial calibration and image measurements using this system. In this paper, we present the details of the hybrid Compton imaging system and initial calibration and image measurements.

  20. Parallel MR Imaging

    PubMed Central

    Deshmane, Anagha; Gulani, Vikas; Griswold, Mark A.; Seiberlich, Nicole

    2015-01-01

    Parallel imaging is a robust method for accelerating the acquisition of magnetic resonance imaging (MRI) data, and has made possible many new applications of MR imaging. Parallel imaging works by acquiring a reduced amount of k-space data with an array of receiver coils. These undersampled data can be acquired more quickly, but the undersampling leads to aliased images. One of several parallel imaging algorithms can then be used to reconstruct artifact-free images from either the aliased images (SENSE-type reconstruction) or from the under-sampled data (GRAPPA-type reconstruction). The advantages of parallel imaging in a clinical setting include faster image acquisition, which can be used, for instance, to shorten breath-hold times resulting in fewer motion-corrupted examinations. In this article the basic concepts behind parallel imaging are introduced. The relationship between undersampling and aliasing is discussed and two commonly used parallel imaging methods, SENSE and GRAPPA, are explained in detail. Examples of artifacts arising from parallel imaging are shown and ways to detect and mitigate these artifacts are described. Finally, several current applications of parallel imaging are presented and recent advancements and promising research in parallel imaging are briefly reviewed. PMID:22696125

  1. 5 CFR 370.104 - Length of details.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Length of details. 370.104 Section 370.104 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS INFORMATION TECHNOLOGY EXCHANGE PROGRAM § 370.104 Length of details. (a) Details may be for a period of between 3...

  2. 46 CFR 24.20-1 - Marine engineering details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Marine engineering details. 24.20-1 Section 24.20-1... Engineering Requirements § 24.20-1 Marine engineering details. (a) All marine engineering details relative to... 40 feet in length will be found in subchapter F (Marine Engineering) of this chapter....

  3. 46 CFR 70.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Electrical engineering details. 70.25-1 Section 70.25-1... General Electrical Engineering Requirements § 70.25-1 Electrical engineering details. All electrical engineering details and installations shall be designed and installed in accordance with subchapter...

  4. 46 CFR 188.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Electrical engineering details. 188.25-1 Section 188.25... GENERAL PROVISIONS General Electrical Engineering Requirements § 188.25-1 Electrical engineering details. (a) The electrical engineering details shall be in accordance with subchapter J...

  5. 46 CFR 90.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Electrical engineering details. 90.25-1 Section 90.25-1... PROVISIONS General Electrical Engineering Requirements § 90.25-1 Electrical engineering details. (a) All electrical engineering details and installations shall be designed and installed in accordance...

  6. 46 CFR 188.20-1 - Marine engineering details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Marine engineering details. 188.20-1 Section 188.20-1... PROVISIONS General Marine Engineering Requirements § 188.20-1 Marine engineering details. (a) The marine engineering details shall be in accordance with Subchapter F (Marine Engineering) of this chapter....

  7. 46 CFR 90.20-1 - Marine engineering details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Marine engineering details. 90.20-1 Section 90.20-1... PROVISIONS General Marine Engineering Requirements § 90.20-1 Marine engineering details. (a) All marine engineering details such as piping, valves, fittings, boilers, pressure vessels, etc., and their...

  8. 14 CFR 29.685 - Control system details.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Control system details. 29.685 Section 29.685 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Control Systems § 29.685 Control system details. (a) Each detail of...

  9. 5 CFR 352.905 - Employees on detail.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 5 Administrative Personnel 1 2013-01-01 2013-01-01 false Employees on detail. 352.905 Section 352.905 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS REEMPLOYMENT RIGHTS Reemployment Rights After Service With the Panama Canal Commission § 352.905 Employees on detail. (a) An employee detailed to the Commission...

  10. Brief Review on Details in Educational Management and Teaching

    ERIC Educational Resources Information Center

    Liang, Yuqin

    2009-01-01

    In reality, quite lots of details are frequently neglected intentionally or unintentionally. Usually, failure is accumulated when one is careless, while success is also accumulated by several details. We human beings often have the exclamation of "Success owing to details, and failure too". We should, from time to time, alarm or remind…

  11. 34 CFR 5.16 - Deletion of identifying details.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 34 Education 1 2010-07-01 2010-07-01 false Deletion of identifying details. 5.16 Section 5.16... details. Whenever any final opinion, order, or other materials required to be made available pursuant to... other identifying details will constitute a clearly unwarranted invasion of personal privacy, the...

  12. 14 CFR 25.685 - Control system details.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Control system details. 25.685 Section 25.685 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... system details. (a) Each detail of each control system must be designed and installed to prevent...

  13. 14 CFR 23.685 - Control system details.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Control system details. 23.685 Section 23.685 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT... Control Systems § 23.685 Control system details. (a) Each detail of each control system must be...

  14. 44 CFR 5.27 - Deletion of identifying details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... details. 5.27 Section 5.27 Emergency Management and Assistance FEDERAL EMERGENCY MANAGEMENT AGENCY... identifying details. To the extent required to prevent a clearly unwarranted invasion of personal privacy, FEMA may delete identifying details when making available or publishing an opinion, statement of...

  15. 46 CFR 32.45-1 - Installation and details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Installation and details. 32.45-1 Section 32.45-1... REQUIREMENTS Electrical Installations § 32.45-1 Installation and details. The installation of all electrical engineering or interior communications systems, together with the details of design, construction,...

  16. 49 CFR 7.6 - Deletion of identifying detail.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 1 2010-10-01 2010-10-01 false Deletion of identifying detail. 7.6 Section 7.6... To Be Made Public by DOT § 7.6 Deletion of identifying detail. Whenever it is determined to be necessary to prevent a clearly unwarranted invasion of personal privacy, identifying details will be...

  17. 46 CFR 90.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Electrical engineering details. 90.25-1 Section 90.25-1... PROVISIONS General Electrical Engineering Requirements § 90.25-1 Electrical engineering details. (a) All electrical engineering details and installations shall be designed and installed in accordance...

  18. 46 CFR 24.20-1 - Marine engineering details.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 1 2014-10-01 2014-10-01 false Marine engineering details. 24.20-1 Section 24.20-1... Engineering Requirements § 24.20-1 Marine engineering details. All marine engineering details relative to the... in length will be found in subchapter F (Marine Engineering) of this chapter....

  19. 46 CFR 24.20-1 - Marine engineering details.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 1 2011-10-01 2011-10-01 false Marine engineering details. 24.20-1 Section 24.20-1... Engineering Requirements § 24.20-1 Marine engineering details. (a) All marine engineering details relative to... 40 feet in length will be found in subchapter F (Marine Engineering) of this chapter....

  20. 46 CFR 70.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 3 2011-10-01 2011-10-01 false Electrical engineering details. 70.25-1 Section 70.25-1... General Electrical Engineering Requirements § 70.25-1 Electrical engineering details. All electrical engineering details and installations shall be designed and installed in accordance with subchapter...

  1. 46 CFR 90.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Electrical engineering details. 90.25-1 Section 90.25-1... PROVISIONS General Electrical Engineering Requirements § 90.25-1 Electrical engineering details. (a) All electrical engineering details and installations shall be designed and installed in accordance...

  2. 46 CFR 90.20-1 - Marine engineering details.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Marine engineering details. 90.20-1 Section 90.20-1... PROVISIONS General Marine Engineering Requirements § 90.20-1 Marine engineering details. (a) All marine engineering details such as piping, valves, fittings, boilers, pressure vessels, etc., and their...

  3. 46 CFR 188.20-1 - Marine engineering details.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 7 2011-10-01 2011-10-01 false Marine engineering details. 188.20-1 Section 188.20-1... PROVISIONS General Marine Engineering Requirements § 188.20-1 Marine engineering details. (a) The marine engineering details shall be in accordance with Subchapter F (Marine Engineering) of this chapter....

  4. 46 CFR 70.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 3 2012-10-01 2012-10-01 false Electrical engineering details. 70.25-1 Section 70.25-1... General Electrical Engineering Requirements § 70.25-1 Electrical engineering details. All electrical engineering details and installations shall be designed and installed in accordance with subchapter...

  5. 46 CFR 188.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 7 2012-10-01 2012-10-01 false Electrical engineering details. 188.25-1 Section 188.25... GENERAL PROVISIONS General Electrical Engineering Requirements § 188.25-1 Electrical engineering details. (a) The electrical engineering details shall be in accordance with subchapter J...

  6. 46 CFR 188.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 7 2011-10-01 2011-10-01 false Electrical engineering details. 188.25-1 Section 188.25... GENERAL PROVISIONS General Electrical Engineering Requirements § 188.25-1 Electrical engineering details. (a) The electrical engineering details shall be in accordance with subchapter J...

  7. 46 CFR 188.20-1 - Marine engineering details.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 7 2013-10-01 2013-10-01 false Marine engineering details. 188.20-1 Section 188.20-1... PROVISIONS General Marine Engineering Requirements § 188.20-1 Marine engineering details. (a) The marine engineering details shall be in accordance with Subchapter F (Marine Engineering) of this chapter....

  8. 46 CFR 24.20-1 - Marine engineering details.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 1 2013-10-01 2013-10-01 false Marine engineering details. 24.20-1 Section 24.20-1... Engineering Requirements § 24.20-1 Marine engineering details. All marine engineering details relative to the... in length will be found in subchapter F (Marine Engineering) of this chapter....

  9. 46 CFR 90.20-1 - Marine engineering details.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Marine engineering details. 90.20-1 Section 90.20-1... PROVISIONS General Marine Engineering Requirements § 90.20-1 Marine engineering details. (a) All marine engineering details such as piping, valves, fittings, boilers, pressure vessels, etc., and their...

  10. 46 CFR 188.20-1 - Marine engineering details.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 7 2012-10-01 2012-10-01 false Marine engineering details. 188.20-1 Section 188.20-1... PROVISIONS General Marine Engineering Requirements § 188.20-1 Marine engineering details. (a) The marine engineering details shall be in accordance with Subchapter F (Marine Engineering) of this chapter....

  11. 46 CFR 90.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Electrical engineering details. 90.25-1 Section 90.25-1... PROVISIONS General Electrical Engineering Requirements § 90.25-1 Electrical engineering details. (a) All electrical engineering details and installations shall be designed and installed in accordance...

  12. 46 CFR 90.20-1 - Marine engineering details.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Marine engineering details. 90.20-1 Section 90.20-1... PROVISIONS General Marine Engineering Requirements § 90.20-1 Marine engineering details. (a) All marine engineering details such as piping, valves, fittings, boilers, pressure vessels, etc., and their...

  13. 46 CFR 70.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 3 2014-10-01 2014-10-01 false Electrical engineering details. 70.25-1 Section 70.25-1... General Electrical Engineering Requirements § 70.25-1 Electrical engineering details. All electrical engineering details and installations shall be designed and installed in accordance with subchapter...

  14. 46 CFR 188.20-1 - Marine engineering details.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 7 2014-10-01 2014-10-01 false Marine engineering details. 188.20-1 Section 188.20-1... PROVISIONS General Marine Engineering Requirements § 188.20-1 Marine engineering details. (a) The marine engineering details shall be in accordance with Subchapter F (Marine Engineering) of this chapter....

  15. 46 CFR 188.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 7 2013-10-01 2013-10-01 false Electrical engineering details. 188.25-1 Section 188.25... GENERAL PROVISIONS General Electrical Engineering Requirements § 188.25-1 Electrical engineering details. (a) The electrical engineering details shall be in accordance with subchapter J...

  16. 46 CFR 70.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 3 2013-10-01 2013-10-01 false Electrical engineering details. 70.25-1 Section 70.25-1... General Electrical Engineering Requirements § 70.25-1 Electrical engineering details. All electrical engineering details and installations shall be designed and installed in accordance with subchapter...

  17. 46 CFR 188.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 7 2014-10-01 2014-10-01 false Electrical engineering details. 188.25-1 Section 188.25... GENERAL PROVISIONS General Electrical Engineering Requirements § 188.25-1 Electrical engineering details. (a) The electrical engineering details shall be in accordance with subchapter J...

  18. 46 CFR 24.20-1 - Marine engineering details.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 1 2012-10-01 2012-10-01 false Marine engineering details. 24.20-1 Section 24.20-1... Engineering Requirements § 24.20-1 Marine engineering details. All marine engineering details relative to the... in length will be found in subchapter F (Marine Engineering) of this chapter....

  19. 46 CFR 90.25-1 - Electrical engineering details.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Electrical engineering details. 90.25-1 Section 90.25-1... PROVISIONS General Electrical Engineering Requirements § 90.25-1 Electrical engineering details. (a) All electrical engineering details and installations shall be designed and installed in accordance...

  20. 46 CFR 90.20-1 - Marine engineering details.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Marine engineering details. 90.20-1 Section 90.20-1... PROVISIONS General Marine Engineering Requirements § 90.20-1 Marine engineering details. (a) All marine engineering details such as piping, valves, fittings, boilers, pressure vessels, etc., and their...

  1. Lightning climatology in the Congo Basin: detailed analysis

    NASA Astrophysics Data System (ADS)

    Soula, Serge; Kigotsi, Jean; Georgis, Jean-François; Barthe, Christelle

    2016-04-01

    The lightning climatology of the Congo Basin including several countries of Central Africa is analyzed in detail for the first time. It is based on World Wide Lightning Location Network (WWLLN) data for the period from 2005 to 2013. A comparison of these data with the Lightning Imaging Sensor (LIS) data for the same period shows the WWLLN detection efficiency (DE) in the region increases from about 1.70 % in the beginning of the period to 5.90 % in 2013, relative to LIS data, but not uniformly over the whole 2750 km × 2750 km area. Both the annual flash density and the number of stormy days show sharp maximum values localized in eastern of Democratic Republic of Congo (DRC) and west of Kivu Lake, regardless of the reference year and the period of the year. These maxima reach 12.86 fl km-2 and 189 days, respectively, in 2013, and correspond with a very active region located at the rear of the Virunga mountain range characterised with summits that can reach 3000 m. The presence of this range plays a role in the thunderstorm development along the year. The estimation of this local maximum of the lightning density by taking into account the DE, leads to a value consistent with that of the global climatology by Christian et al. (2003) and other authors. Thus, a mean maximum value of about 157 fl km-2 y-1 is found for the annual lightning density. The zonal distribution of the lightning flashes exhibits a maximum between 1°S and 2°S and about 56 % of the flashes located below the equator in the 10°S - 10°N interval. The diurnal evolution of the flash rate has a maximum between 1400 and 1700 UTC, according to the reference year, in agreement with previous works in other regions of the world.

  2. Interpretation of 2d and 3d Building Details on Facades and Roofs

    NASA Astrophysics Data System (ADS)

    Meixner, P.; Leberl, F.; Brédif, M.

    2011-04-01

    Current Internet-inspired mapping data are in the form of street maps, orthophotos, 3D models or street-side images and serve to support mostly search and navigation. Yet the only mapping data that currently can really be searched are the street maps via their addresses and coordinates. The orthophotos, 3D models and street-side images represent predominantly "eye candy" with little added value to the Internet-user. We are interested in characterizing the elements of the urban space from imagery. In this paper we discuss the use of street side imagery and aerial imagery to develop descriptions of urban spaces, initially of building facades and roofs. We present methods (a) to segment facades using high-overlap street side facade images, (b) to map facades and facade details from vertical aerial images, and (c) to characterize roofs by their type and details, also from aerial photography. This paper describes a method of roof segmentation with the goal of assigning each roof to a specific architectural style. Questions of the use of the attic space, or the placement of solar panels, are of interest. It is of interest that roofs have recently been mapped using LiDAR point clouds. We demonstrate that aerial images are a useful and economical alternative to LiDAR for the characterization of building roofs, and that they also contain very valuable information about facades.

  3. Use of MEMs and optical sensors for closed loop heliostat control

    NASA Astrophysics Data System (ADS)

    Harper, Paul Julian; Dreijer, Janto; Malan, Karel; Larmuth, James; Gauche, Paul

    2016-05-01

    The Helio 100 project at STERG (Stellenbosch Solar Thermal Research Group) aims to help reduce the cost of Concentrated Solar Thermal plants by deploying large numbers of small (1x2 m) low cost heliostats. One of the methods employed to reduce the cost of the heliostat field is to have a field that requires no site preparation (grading, leveling, vegetation clearance) and no expensive foundations or concrete pouring for each individual heliostat base. This implies that the heliostat pod frames and vertical mounts might be slightly out of vertical, and the normal method of dead reckoning using accurately surveyed and aligned heliostat bases cannot be used. This paper describes a combination of MEMs and optical sensors on the back of the heliostat, that together with a simple machine learning approach, give accurate and reproducible azimuth and elevation information for the heliostat plane. Initial experiments were done with an android phone mounted on the back of a heliostat as it was a readily available platform combining accelerometers' and camera into one programmable package. It was found quite easy to determine the pointing angle of the heliostat to within 1 milliradian using the rear facing camera and correlating known heliostat angles with target image features on the ground. We also tested the accuracy at various image resolutions by halving the image size successively till the feature detection failed. This showed that even a VGA (640x480) resolution image could give mean errors of 1.5 milliradian. The optical technique is exceedingly simple and does not use any camera calibration, angular reconstruction or knowledge of heliostat drive geometry. We also tested the ability of the 3d accelerometers to determine angle, but this was coarser than the camera and only accurate to around 10 milliradians.

  4. Recovering and preventing loss of detailed memory: differential rates of forgetting for detail types in episodic memory.

    PubMed

    Sekeres, Melanie J; Bonasia, Kyra; St-Laurent, Marie; Pishdadian, Sara; Winocur, Gordon; Grady, Cheryl; Moscovitch, Morris

    2016-02-01

    Episodic memories undergo qualitative changes with time, but little is known about how different aspects of memory are affected. Different types of information in a memory, such as perceptual detail, and central themes, may be lost at different rates. In patients with medial temporal lobe damage, memory for perceptual details is severely impaired, while memory for central details is relatively spared. Given the sensitivity of memory to loss of details, the present study sought to investigate factors that mediate the forgetting of different types of information from naturalistic episodic memories in young healthy adults. The study investigated (1) time-dependent loss of "central" and "peripheral" details from episodic memories, (2) the effectiveness of cuing with reminders to reinstate memory details, and (3) the role of retrieval in preventing forgetting. Over the course of 7 d, memory for naturalistic events (film clips) underwent a time-dependent loss of peripheral details, while memory for central details (the core or gist of events) showed significantly less loss. Giving brief reminders of the clips just before retrieval reinstated memory for peripheral details, suggesting that loss of details is not always permanent, and may reflect both a storage and retrieval deficit. Furthermore, retrieving a memory shortly after it was encoded prevented loss of both central and peripheral details, thereby promoting retention over time. We consider the implications of these results for behavioral and neurobiological models of retention and forgetting. PMID:26773100

  5. Detailed description of the Mayo/IBM PACS

    NASA Astrophysics Data System (ADS)

    Gehring, Dale G.; Persons, Kenneth R.; Rothman, Melvyn L.; Salutz, James R.; Morin, Richard L.

    1991-07-01

    The Mayo Clinic and IBM/Rochester have jointly developed a picture archiving system (PACS) for use with Mayo's MRI and Neuro-CT imaging modalities. The system was developed to replace the imaging system's vendor-supplied magnetic tape archiving capability. The system consists of seven MR imagers and nine CT scanners, each interfaced to the PACS via IBM Personal System/2(tm) (PS/2) computers, which act as gateways from the imaging modality to the PACS network. The PAC system operates on the token-ring component of Mayo's city-wide local area network. Also on the PACS network are four optical storage subsystems used for image archival, three optical subsystems used for image retrieval, an IBM Application System/400(tm) (AS/400) computer used for database management and multiple PS/2-based image display systems and their image servers.

  6. Details of insect wing design and deformation enhance aerodynamic function and flight efficiency.

    PubMed

    Young, John; Walker, Simon M; Bomphrey, Richard J; Taylor, Graham K; Thomas, Adrian L R

    2009-09-18

    Insect wings are complex structures that deform dramatically in flight. We analyzed the aerodynamic consequences of wing deformation in locusts using a three-dimensional computational fluid dynamics simulation based on detailed wing kinematics. We validated the simulation against smoke visualizations and digital particle image velocimetry on real locusts. We then used the validated model to explore the effects of wing topography and deformation, first by removing camber while keeping the same time-varying twist distribution, and second by removing camber and spanwise twist. The full-fidelity model achieved greater power economy than the uncambered model, which performed better than the untwisted model, showing that the details of insect wing topography and deformation are important aerodynamically. Such details are likely to be important in engineering applications of flapping flight. PMID:19762645

  7. Detailed model of the thorax as a volume conductor based on the visible human man data.

    PubMed

    Kauppinen, P; Hyttinen, J; Heinonen, T; Malmivuo, J

    1998-01-01

    A large number of computerized conductivity models of the human thorax have been created to study bioelectric phenomena in human beings. Devised models have varied greatly in the level of anatomical detail incorporated thus restricting the accuracy and validity of conducted simulations. This paper introduces a highly detailed anatomically accurate three-dimensional computer model of the conductive anatomy of the human thorax for calculating electric fields generated by equivalent bioelectric sources and different externally applied sources. The anatomy of the devised model is based on high resolution colour cryosection images of the US National Library of Medicine's Visible Human Man data set and is comprised of more anatomical detail than prior computer models. The model is based on the finite difference method and is readily applicable for the analysis of a wide range of biomedical field problems, such as electrocardiography, impedance cardiography, tissue stimulations, and especially, in development of measurement systems. PMID:9667039

  8. Detail of proscenium opening. San bernardino Valley Union Junior College, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail of proscenium opening. San bernardino Valley Union Junior College, Auditorium Building. Details of corbels and soffit; lettering detail for frieze. G. Stanley Wilson, Architect, A.I.A., Riverside, California. Sheet W.P.A. 2, job no. 692. Scale 3/4 inch to the foot. May 18, 1937. (no state stamp. - San Bernardino Valley College, Auditorium, 701 South Mount Vernon Avenue, San Bernardino, San Bernardino County, CA

  9. High throughput, detailed, cell-specific neuroanatomy of dendritic spines using microinjection and confocal microscopy

    PubMed Central

    Dumitriu, Dani; Rodriguez, Alfredo; Morrison, John H.

    2012-01-01

    Morphological features such as size, shape and density of dendritic spines have been shown to reflect important synaptic functional attributes and potential for plasticity. Here we describe in detail a protocol for obtaining detailed morphometric analysis of spines using microinjection of fluorescent dyes, high resolution confocal microscopy, deconvolution and image analysis using NeuronStudio. Recent technical advancements include better preservation of tissue resulting in prolonged ability to microinject, and algorithmic improvements that compensate for the residual Z-smear inherent in all optical imaging. Confocal imaging parameters were probed systematically for the identification of both optimal resolution as well as highest efficiency. When combined, our methods yield size and density measurements comparable to serial section transmission electron microscopy in a fraction of the time. An experiment containing 3 experimental groups with 8 subjects in each can take as little as one month if optimized for speed, or approximately 4 to 5 months if the highest resolution and morphometric detail is sought. PMID:21886104

  10. Detail of arched windows on north elevation; camera facing southwest. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail of arched windows on north elevation; camera facing southwest. - Mare Island Naval Shipyard, Smithery, California Avenue, west side at California Avenue & Eighth Street, Vallejo, Solano County, CA

  11. DETAIL VIEW OF SOUTH FRONT DOORS, FACING NORTHEAST. Douglas ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DETAIL VIEW OF SOUTH FRONT DOORS, FACING NORTHEAST. - Douglas Aircraft Company Long Beach Plant, Aircraft Wing & Fuselage Assembly Building, 3855 Lakewood Boulevard, Long Beach, Los Angeles County, CA

  12. 18. Detail of stonework, north side, immediately west of western ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    18. Detail of stonework, north side, immediately west of western abutment reinforcing, facing south. - Dubbs Bridge, Spinnerstown Road (State Route 2031) spanning Hosensack Creek, Dillingerville, Lehigh County, PA

  13. 93. TOWER STAIRHALL, SOUTH WALL, WEST TABERNACLE FRAME. DETAIL OF ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    93. TOWER STAIRHALL, SOUTH WALL, WEST TABERNACLE FRAME. DETAIL OF DOG EAR AND TRUSS (BRACKET) - Independence Hall Complex, Independence Hall, 500 Chestnut Street, Philadelphia, Philadelphia County, PA

  14. DETAIL VIEW, SOUTH PORTICO, CENTER DOOR OPENING CONTAINING FRENCH WINDOWS. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DETAIL VIEW, SOUTH PORTICO, CENTER DOOR OPENING CONTAINING FRENCH WINDOWS. (NOTE THE INCISED STUCCO MIMICKING ASHLAR STONE COURSING - The Woodlands, 4000 Woodlands Avenue, Philadelphia, Philadelphia County, PA

  15. 1. PLAN, ELEVATIONS, SECTION, DETAIL (Surviving portion of facade incorporated ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. PLAN, ELEVATIONS, SECTION, DETAIL (Surviving portion of facade incorporated into Pan Am Building, Strandgade) - Strandgade (House), Corner of Strand Street & Queen's Cross Street, Christiansted, St. Croix, VI

  16. Historic American Buildings Survey Marc Blair Photographer, summer 1966 DETAIL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Historic American Buildings Survey Marc Blair Photographer, summer 1966 DETAIL of SOUTH ELEVATION - Grace Protestant Episcopal Church, 1041 Wisconsin Avenue Northwest, Washington, District of Columbia, DC

  17. 37. Attic, south wall, detail of radiator Veterans Administration ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    37. Attic, south wall, detail of radiator - Veterans Administration Center, Officers Duplex Quarters, 5302 East Kellogg (Legal Address); 5500 East Kellogg (Common Address), Wichita, Sedgwick County, KS

  18. Marguerite Arnet Residence, exterior window detail, looking north. Adam ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Marguerite Arnet Residence, exterior window detail, looking north. - Adam & Bessie Arnet Homestead, Marguerite Arnet Residence, 560 feet northeast of Adam & Bessie Arnet Residence, Model, Las Animas County, CO

  19. Marguerite Arnet Residence, exterior door detail, looking north. Adam ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Marguerite Arnet Residence, exterior door detail, looking north. - Adam & Bessie Arnet Homestead, Marguerite Arnet Residence, 560 feet northeast of Adam & Bessie Arnet Residence, Model, Las Animas County, CO

  20. DETAIL OF PLAQUE WITH ADDITIONAL DESIGN AND CONSTRUCTION INFORMATION, SOUTHEAST ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DETAIL OF PLAQUE WITH ADDITIONAL DESIGN AND CONSTRUCTION INFORMATION, SOUTHEAST ABUTMENT - Connecticut Avenue Bridge, Spans Rock Creek & Potomac Parkway at Connecticut Avenue, Washington, District of Columbia, DC

  1. 63. INTERIOR VIEW, DETAIL, HEAD HOUSE, GROUND FLOOR, BARLOW ROOM, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    63. INTERIOR VIEW, DETAIL, HEAD HOUSE, GROUND FLOOR, BARLOW ROOM, CARVED LINOLEUM WALL PANEL FLANKING THE ENTRANCE, LOOKING WEST - Timberline Lodge, Timberline Trail, Government Camp, Clackamas County, OR

  2. 64. INTERIOR VIEW, DETAIL, HEAD HOUSE, GROUND FLOOR, BARLOW ROOM, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    64. INTERIOR VIEW, DETAIL, HEAD HOUSE, GROUND FLOOR, BARLOW ROOM, CARVED LINOLEUM WALL PANEL FLANKING THE ENTRANCE, LOOKING WEST - Timberline Lodge, Timberline Trail, Government Camp, Clackamas County, OR

  3. MEMORIAL TO SOLDIERS WHO DIED FOR THIS COUNTRY (OBELISK), DETAIL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    MEMORIAL TO SOLDIERS WHO DIED FOR THIS COUNTRY (OBELISK), DETAIL SHOWING INSCRIPTION ON FRONT ELEVATION. VIEW TO NORTHEAST. - Leavenworth National Cemetery, 150 Muncie Road, Leavenworth, Leavenworth County, KS

  4. A new debate for Turkish physicians: e-detailing.

    PubMed

    Ventura, Keti; Baybars, Miray; Dedeoglu, Ayla Ozhan

    2012-01-01

    The study presents an empirical analysis of the attitudes of Turkish physicians towards e-detailing practices compared to face-to-face detailing. The findings reveal that although physicians have positive attitudes toward e-detailing, on some points they are still undecided and/or have doubts. The structural model revealed that affect, convenience, and informative content influence their attitude in a positive manner, whereas the personal interaction was found to be a negative factor. Physicians' age and frequency of calls received from representatives are moderators. The present study can be seen as an addition to pharmaceutical marketing, an underresearched study field in Turkey, and e-detailing particularly. PMID:23210675

  5. 17. DETAIL OF BUILDER'S PLAQUE, LOOKING NORTH. Philadelphia & ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    17. DETAIL OF BUILDER'S PLAQUE, LOOKING NORTH. - Philadelphia & Reading Railroad, Wissahickon Creek Viaduct, Spanning Wissahickon Creek, north of Ridge Avenue Bridge, Philadelphia, Philadelphia County, PA

  6. 16. DETAIL OF SMALL ARCHES AT SOUTH END, FROM WEST. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    16. DETAIL OF SMALL ARCHES AT SOUTH END, FROM WEST. - Philadelphia & Reading Railroad, Wissahickon Creek Viaduct, Spanning Wissahickon Creek, north of Ridge Avenue Bridge, Philadelphia, Philadelphia County, PA

  7. 15. DETAIL OF SMALL ARCHES AT SOUTH END, FROM WEST. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    15. DETAIL OF SMALL ARCHES AT SOUTH END, FROM WEST. - Philadelphia & Reading Railroad, Wissahickon Creek Viaduct, Spanning Wissahickon Creek, north of Ridge Avenue Bridge, Philadelphia, Philadelphia County, PA

  8. 7. VIEW NORTHWEST, DETAIL VERTICAL SUPPORT SYSTEM, STRINGER, CONNECTIONS AND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    7. VIEW NORTHWEST, DETAIL VERTICAL SUPPORT SYSTEM, STRINGER, CONNECTIONS AND TRAFFIC DECK - Hagerstown Road Bridge, Spanning Little Cotoctin Creek at Old Hagerstown Road, Middletown, Frederick County, MD

  9. 6. DETAIL OF CORNICE, ROOF AND WINDOWS, VIEW TO SOUTHEAST ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    6. DETAIL OF CORNICE, ROOF AND WINDOWS, VIEW TO SOUTHEAST - Providence Sewage Treatment System, Ernest Street Pumping Station, Boiler House, Ernest Street & Allens Avenue, Providence, Providence County, RI

  10. INTERIOR SECOND FLOOR EAST ENGINEERING DESIGN AREA DETAIL VIEW, FACING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    INTERIOR SECOND FLOOR EAST ENGINEERING DESIGN AREA DETAIL VIEW, FACING NORTH. - NASA Industrial Plant, Systems Integration & Checkout Facility, 12214 Lakewood Boulevard, Downey, Los Angeles County, CA

  11. 11. VIEW NORTHEAST, DETAIL OF BRIDGE BEARING AT SOUTHEAST CORNER, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    11. VIEW NORTHEAST, DETAIL OF BRIDGE BEARING AT SOUTHEAST CORNER, SHOWING WELDED REINFORCEMENT - Perkins Corner Bridge, Spanning Willimantic River at Flanders & Cider Mill Roads, Coventry, Tolland County, CT

  12. Interior view, detail of the staircase to show the burnished ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Interior view, detail of the staircase to show the burnished aluminum and brass balustrade - Departmental Auditorium, Constitution Avenue between Twelfth and Fourteenth Streets, Washington, District of Columbia, DC

  13. 18. DETAIL OF ORIGINAL INTERIOR DOOR AND HARDWARE A. C. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    18. DETAIL OF ORIGINAL INTERIOR DOOR AND HARDWARE A. C. Eschete, photographer, September 24, 1977 - Bagatelle Plantation, East River Road (moved to Iberville Parish), Donaldsonville, Ascension Parish, LA

  14. 18. DETAIL, INSPECTION PIT Delaware, Lackawanna & Western Railroad ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    18. DETAIL, INSPECTION PIT - Delaware, Lackawanna & Western Railroad Freight & Rail Yard, Multiple Unit Light Inspection Shed, New Jersey Transit Hoboken Terminal Rail Yard, Hoboken, Hudson County, NJ

  15. 22. DETAIL, WOOD BLOCK FLOOR Delaware, Lackawanna & Western ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    22. DETAIL, WOOD BLOCK FLOOR - Delaware, Lackawanna & Western Railroad Freight & Rail Yard, Multiple Unit Light Inspection Shed, New Jersey Transit Hoboken Terminal Rail Yard, Hoboken, Hudson County, NJ

  16. 12. DETAIL, TYPICAL WINDOW BAY Delaware, Lackawanna & Western ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    12. DETAIL, TYPICAL WINDOW BAY - Delaware, Lackawanna & Western Railroad Freight & Rail Yard, Multiple Unit Light Inspection Shed, New Jersey Transit Hoboken Terminal Rail Yard, Hoboken, Hudson County, NJ

  17. 19. DETAIL, OVERHEAD CATWALK Delaware, Lackawanna & Western Railroad ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    19. DETAIL, OVERHEAD CATWALK - Delaware, Lackawanna & Western Railroad Freight & Rail Yard, Multiple Unit Light Inspection Shed, New Jersey Transit Hoboken Terminal Rail Yard, Hoboken, Hudson County, NJ

  18. Interior detail of dispatch boards in main hall, facing west ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Interior detail of dispatch boards in main hall, facing west - International Longshoremen's & Warehousemen's Union Hall, Naval Civil Engineering Laboratory, Port Hueneme Road, Port Hueneme, Ventura County, CA

  19. 9. DETAIL VIEW OF SPANDREL WALL AT ABUTMENT AND INTERSECTION ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    9. DETAIL VIEW OF SPANDREL WALL AT ABUTMENT AND INTERSECTION WITH FOUNDATION OF ADJOINING BUILDING - Sanderson Avenue Bridge, Sanderson Avenue spanning Lackawanna River, Scranton, Lackawanna County, PA

  20. 21. DETAIL VIEW OF MARSICAL WORKS CONDENSERS INCLUDING QUICKSILVER COLLECTION ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    21. DETAIL VIEW OF MARSICAL WORKS CONDENSERS INCLUDING QUICKSILVER COLLECTION CHANNEL AND COLLECTION BOX, CENTER FOREGROUND, LOOKING SOUTH, SOUTHEAST. - Mariscal Quicksilver Mine & Reduction Works, Terlingua, Brewster County, TX

  1. 29. Detail view north showing amperage and voltage meters, operator's ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    29. Detail view north showing amperage and voltage meters, operator's room, west operator's house. - Yellow Mill Bridge, Spanning Yellow Mill Channel at Stratford Avenue, Bridgeport, Fairfield County, CT

  2. TENANT HOUSE, WINDOW DETAIL, NORTH FRONT, LOOKING SOUTH Irvine ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    TENANT HOUSE, WINDOW DETAIL, NORTH FRONT, LOOKING SOUTH - Irvine Ranch Agricultural Headquarters, Carillo Tenant House, Southwest of Intersection of San Diego & Santa Ana Freeways, Irvine, Orange County, CA

  3. Detail view to show northwestern section of the building with ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail view to show northwestern section of the building with its modified mansard roof - Internal Revenue Service Headquarters Building, 1111 Constitution Avenue Northwest, Washington, District of Columbia, DC

  4. Detail of main entrance; camera facing southwest. Mare Island ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail of main entrance; camera facing southwest. - Mare Island Naval Shipyard, Hospital Headquarters, Johnson Lane, west side at intersection of Johnson Lane & Cossey Street, Vallejo, Solano County, CA

  5. 9. DETAIL, NORTH FRONT, CENTRAL (TALLEST) TOWER, FROM THE NORTHWEST ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    9. DETAIL, NORTH FRONT, CENTRAL (TALLEST) TOWER, FROM THE NORTHWEST - Smithsonian Institution Building, 1000 Jefferson Drive, between Ninth & Twelfth Streets, Southwest, Washington, District of Columbia, DC

  6. 7. DETAIL, NORTH FRONT, EASTERN PORTION OF MAIN BLOCK, WINDOWS ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    7. DETAIL, NORTH FRONT, EASTERN PORTION OF MAIN BLOCK, WINDOWS - Smithsonian Institution Building, 1000 Jefferson Drive, between Ninth & Twelfth Streets, Southwest, Washington, District of Columbia, DC

  7. Interior detail of tower space; camera facing southwest. Mare ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Interior detail of tower space; camera facing southwest. - Mare Island Naval Shipyard, Defense Electronics Equipment Operating Center, I Street, terminus west of Cedar Avenue, Vallejo, Solano County, CA

  8. 20. INTERIOR, OPERATOR'S HOUSE, OPERATING EQUIPMENT, DETAIL New York, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    20. INTERIOR, OPERATOR'S HOUSE, OPERATING EQUIPMENT, DETAIL - New York, New Haven & Hartford Railroad, Groton Bridge, Spanning Thames River between New London & Groton, New London, New London County, CT

  9. INTERIOR FIRST FLOOR WEST CENTRAL ELEVATOR LOBBY DETAIL VIEW, FACING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    INTERIOR FIRST FLOOR WEST CENTRAL ELEVATOR LOBBY DETAIL VIEW, FACING SOUTHEAST. - NASA Industrial Plant, Systems Integration & Checkout Facility, 12214 Lakewood Boulevard, Downey, Los Angeles County, CA

  10. 19. DETAIL VIEW OF LATERAL BRACING, NORTH ELEVATION, LOOKING NORTHWEST ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    19. DETAIL VIEW OF LATERAL BRACING, NORTH ELEVATION, LOOKING NORTHWEST - Mystic River Drawbridge No. 7, Spanning Mystic River at Boston & Maine Railroad Eastern Route, Somerville, Middlesex County, MA

  11. 2. DETAIL VIEW OF MIDDLE ARCH SPAN, LOOKING NORTHWEST. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    2. DETAIL VIEW OF MIDDLE ARCH SPAN, LOOKING NORTHWEST. - Cumberland & Pennsylvania Railroad, Wills Creek Bridge, Spanning Wills Creek 587 feet West of Eckhart Junction, Cumberland, Allegany County, MD

  12. 3. Historic American Buildings Survey, 1966, INTERIOR, DETAIL, ENCLOSED STAIRCASE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. Historic American Buildings Survey, 1966, INTERIOR, DETAIL, ENCLOSED STAIRCASE AND TIN SHEETING. - Sig Sautelle Circus Training House, South Main Street (State Route 11), Homer, Cortland County, NY

  13. Detail of door on southeast elevation. View to northwest ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail of door on southeast elevation. View to northwest - Flint Creek Hydroelectric Project, Powerhouse, Approximately 3 miles southeast of Porters Corner on Powerhouse Road, Philipsburg, Granite County, MT

  14. 7. DETAIL, WINDOWS AND SAFETY LADDER AT RECEIVING DEPARTMENT, NORTH ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    7. DETAIL, WINDOWS AND SAFETY LADDER AT RECEIVING DEPARTMENT, NORTH SIDE, NEAR WEST END. - United Engineering Company Shipyard, Inspection & Repair Shops, 2900 Main Street, Alameda, Alameda County, CA

  15. 10. Detail, northerly spans, west side, showing deterioration; note spalls, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    10. Detail, northerly spans, west side, showing deterioration; note spalls, cracks, and efflorescence; view to southeast. - Fordway Bridge, Spanning Concord River at Pollard Street, Billerica, Middlesex County, MA

  16. Detail of window on south elevation; camera facing north. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail of window on south elevation; camera facing north. - Mare Island Naval Shipyard, Ordnance Warehouse, Blake Avenue, northeast corner of Blake Avenue & Railroad Avenue, Vallejo, Solano County, CA

  17. Interior detail of structural elements section; camera facing east. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Interior detail of structural elements section; camera facing east. - Mare Island Naval Shipyard, Supply Building, Walnut Avenue, southeast corner of Walnut Avenue & Fifth Street, Vallejo, Solano County, CA

  18. 7. SOUTHEAST REAR DETAIL, SHOWING WINDOWS. VIEW TO NORTHWEST. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    7. SOUTHEAST REAR DETAIL, SHOWING WINDOWS. VIEW TO NORTHWEST. - Commercial & Industrial Buildings, Key City Electric Street Railroad, Powerhouse & Storage Barn, Eighth & Washington Streets, Dubuque, Dubuque County, IA

  19. Current status of the laser diode array projector technology

    NASA Astrophysics Data System (ADS)

    Beasley, D. Brett; Saylor, Daniel A.

    1998-07-01

    This paper describes recent developments and the current status of the Laser Diode Array Projector (LDAP) Technology. The LDAP is a state-of-the-art dynamic infrared scene projector system capable of generating high resolution in-band infrared imagery at high frame rates. Three LDAPs are now operational at the U.S. Army Aviation and Missile Command's (AMCOM) Missile Research, Development, and Engineering Center (MRDEC). These projectors have been used to support multiple Hardware-in-the-Loop test entries of various seeker configurations. Seeker configurations tested include an InSb 256 X $256 focal-plane array (FPA), an InSb 512 X 512 FPA, a PtSi 640 X 480 FPA, a PtSi 256 X 256 FPA, an uncooled 320 X 240 microbolometer FPA, and two dual field- of-view (FOV) seekers. Several improvements in the projector technology have been made since we last reported in 1997. The format size has been increased to 544 X 544, and 672 X 512, and it has been proven that the LDAP can be synchronized without a signal from the unit-under test (UUT). The control software has been enhanced to provide 'point and click' control for setup, calibration, image display, image capture, and data analysis. In addition, the first long-wave infrared (LWIR) LDAP is now operational, as well as a dual field of view LDAP which can change its FOV within 0.25 seconds. The projector is interfaced to a Silicon Graphics scene generation computer which is capable of real-time 3-D scene generation. Sample images generated with the projector and captured by an InSb FPA sensor are included in the text.

  20. Imaging of MELAS.

    PubMed

    Malhotra, Konark; Liebeskind, David S

    2016-09-01

    Mitochondrial diseases are multisystem disorders that frequently involve the central nervous system. The clinical presentation of these disorders may be challenging to differentiate from cerebrovascular disorders. Various imaging techniques are now available that provide a wide range of imaging modalities during initial clinical evaluation and throughout the disease course. Recent technological advancements have introduced advanced neuroimaging modalities that provide detailed information of metabolic disorders at the tissue level. Imaging findings, though diverse, usually have characteristic features that support differentiating these disorders from vascular syndromes. This article provides an overview of various neuroimaging modalities available along with the advent of new imaging techniques being utilized in these disorders. PMID:27477183

  1. Ideas and Details: A Guide to College Writing. Third Edition.

    ERIC Educational Resources Information Center

    Bauman, M. Garrett

    The goal of this guidebook is to help writers activate their brains to stir up more and better ideas and details. The guide's thesis is that "good writing combines fresh ideas energized by vivid details." Chapters 1, 2, and 3 are devoted to providing thinking options for writers. Chapters 4 and 5 discuss options for paragraphing and organization.…

  2. 46 CFR 77.03-1 - Installation and details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... MISCELLANEOUS SYSTEMS AND EQUIPMENT Marine Engineering Systems § 77.03-1 Installation and details. (a) The installation of all systems of a marine engineering nature, together with the details of design, construction... this chapter. Systems of this type include the following: Steering systems. Power for going...

  3. 46 CFR 77.03-1 - Installation and details.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... MISCELLANEOUS SYSTEMS AND EQUIPMENT Marine Engineering Systems § 77.03-1 Installation and details. (a) The installation of all systems of a marine engineering nature, together with the details of design, construction... this chapter. Systems of this type include the following: Steering systems. Power for going...

  4. 46 CFR 77.03-1 - Installation and details.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... MISCELLANEOUS SYSTEMS AND EQUIPMENT Marine Engineering Systems § 77.03-1 Installation and details. (a) The installation of all systems of a marine engineering nature, together with the details of design, construction... this chapter. Systems of this type include the following: Steering systems. Power for going...

  5. 46 CFR 77.03-1 - Installation and details.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... MISCELLANEOUS SYSTEMS AND EQUIPMENT Marine Engineering Systems § 77.03-1 Installation and details. (a) The installation of all systems of a marine engineering nature, together with the details of design, construction... this chapter. Systems of this type include the following: Steering systems. Power for going...

  6. 46 CFR 77.03-1 - Installation and details.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... MISCELLANEOUS SYSTEMS AND EQUIPMENT Marine Engineering Systems § 77.03-1 Installation and details. (a) The installation of all systems of a marine engineering nature, together with the details of design, construction... this chapter. Systems of this type include the following: Steering systems. Power for going...

  7. 3. Detail of airplane tail protruding out of hangar doors, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. Detail of airplane tail protruding out of hangar doors, dock no. 491. Detail of canvas gasket allowing doors to close tightly around fuselage. View to north. - Offutt Air Force Base, Looking Glass Airborne Command Post, Nose Docks, On either side of Hangar Access Apron at Northwest end of Project Looking Glass Historic District, Bellevue, Sarpy County, NE

  8. 17. DETAIL OF INTERIOR AND EXTERIOR WALL CONSTRUCTION, VIEW TOWARD ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    17. DETAIL OF INTERIOR AND EXTERIOR WALL CONSTRUCTION, VIEW TOWARD NORTHEAST CORNER, THIRD BAY Showing insulated exterior wall at right; asphalt felt on interior separation wall at left; sill beam, stud, and concrete foundation detailing of interior wall. - U.S. Military Academy, Ice House, Mills Road at Howze Place, West Point, Orange County, NY

  9. 46 CFR 56.75-25 - Detail requirements.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 2 2014-10-01 2014-10-01 false Detail requirements. 56.75-25 Section 56.75-25 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Brazing § 56.75-25 Detail requirements. (a) Pipe may be fabricated by brazing when the temperature to which such connections may be...

  10. 46 CFR 113.30-25 - Detailed requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Detailed requirements. 113.30-25 Section 113.30-25 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING COMMUNICATION AND ALARM SYSTEMS AND EQUIPMENT Internal Communications § 113.30-25 Detailed requirements. (a) Multiple stations must be able to communicate at the...

  11. The Seductive Details Effect in Technology-Delivered Instruction

    ERIC Educational Resources Information Center

    Towler, Annette; Kraiger, Kurt; Sitzmann, Traci; Van Overberghe, Courtney; Cruz, Jaime; Ronen, Eyal; Stewart, David

    2008-01-01

    Seductive details are highly interesting information tangential to course objectives. The inclusion of seductive details generally harms performance on recall tests, but few studies have used multimedia training or investigated effects on performance on recognition tests or transfer tasks. We conducted two studies using computer-based training,…

  12. 5 CFR 370.107 - Details to small business concerns.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Details to small business concerns. 370.107 Section 370.107 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS INFORMATION TECHNOLOGY EXCHANGE PROGRAM § 370.107 Details to small business concerns. (a) The head of...

  13. 40 CFR 35.917-4 - Planning scope and detail.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Planning scope and detail. 35.917-4 Section 35.917-4 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works-Clean Water Act § 35.917-4 Planning scope and detail. (a) Initially,...

  14. 27 CFR 19.732 - Details of daily records.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Details of daily records. 19.732 Section 19.732 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS DISTILLED SPIRITS PLANTS Records and Reports Records § 19.732 Details of daily records. The daily...

  15. 46 CFR 195.03-1 - Installation and details.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 7 2013-10-01 2013-10-01 false Installation and details. 195.03-1 Section 195.03-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Marine Engineering Systems § 195.03-1 Installation and details. (a) The installation of all systems...

  16. 46 CFR 195.03-1 - Installation and details.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 7 2012-10-01 2012-10-01 false Installation and details. 195.03-1 Section 195.03-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Marine Engineering Systems § 195.03-1 Installation and details. (a) The installation of all systems...

  17. The Consequences of Including Seductive Details during Lecture

    ERIC Educational Resources Information Center

    Harp, Shannon F.; Maslich, Amy A.

    2005-01-01

    When text passages include seductive details (i.e., interesting, tangentially related adjuncts that are irrelevant to the lesson), students perform worse on recall (Garner, Gillingham, & White, 1989) and problem-solving tests (Harp & Mayer, 1997, 1998) than students reading the same material without seductive details. To determine whether…

  18. Processing and Recall of Seductive Details in Scientific Text

    ERIC Educational Resources Information Center

    Lehman, Stephen; Schraw, Gregory; McCrudden, Matthew T.; Hartley, Kendall

    2007-01-01

    This study examined how seductive details affect on-line processing of a technical, scientific text. In Experiment 1, each sentence from the experimental text was rated for interest and importance. Participants rated seductive details as being more interesting but less important than main ideas. In Experiment 2, we examined the effect of seductive…

  19. Detail view of the west end of the bridge, from ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail view of the west end of the bridge, from the south side, looking northwest, showing construction and masonry details - Beartooth Highway, Little Bear Creek Bridge No. 2, Spanning Little Bear Creek on U.S. Highway 212 at Milepost 29.0, Cody, Park County, WY

  20. Detail view of the west end of the bridge, from ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail view of the west end of the bridge, from the north side, looking south, showing the construction and masonry details - Beartooth Highway, Little Bear Creek Bridge No. 1, Spanning Little Bear Creek on U.S. Highway 212 at Milepost 28.2, Cody, Park County, WY

  1. Detail view of the west end of the bridge, from ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail view of the west end of the bridge, from the south side, looking north, showing construction and masonry details - Beartooth Highway, Little Bear Creek Bridge No. 2, Spanning Little Bear Creek on U.S. Highway 212 at Milepost 29.0, Cody, Park County, WY

  2. Detail view of the bridge, from the south side, looking ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail view of the bridge, from the south side, looking north, showing construction and masonry details - Beartooth Highway, Little Bear Creek Bridge No. 2, Spanning Little Bear Creek on U.S. Highway 212 at Milepost 29.0, Cody, Park County, WY

  3. Detail view of the east end of the bridge, from ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail view of the east end of the bridge, from the north side, looking south, showing construction and masonry details - Beartooth Highway, Little Bear Creek Bridge No. 2, Spanning Little Bear Creek on U.S. Highway 212 at Milepost 29.0, Cody, Park County, WY

  4. 46 CFR 70.20-1 - Marine engineering details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Marine engineering details. 70.20-1 Section 70.20-1... General Marine Engineering Requirements § 70.20-1 Marine engineering details. All marine engineering... subchapter F (Marine Engineering) of this chapter....

  5. 10. Photocopy detail of blueprint (original blueprint located at the ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    10. Photocopy detail of blueprint (original blueprint located at the Nevada State Historical Society in Reno); Crushing Plant (Feature 19) type. CONSULTING ENGINEER'S OFFICE, INTERNATIONAL SMELTING & REFINING CO.,'COPPER CANYON LEASE CRUSHING PLANT FOUNDATION & DETAILS,' JULY 2, 1941. - Copper Canyon Camp of the International Smelting & Refining Company, Crushing Plant, Copper Canyon, Battle Mountain, Lander County, NV

  6. 30 CFR 18.60 - Detailed inspection of components.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Detailed inspection of components. 18.60 Section 18.60 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC MOTOR-DRIVEN MINE EQUIPMENT AND ACCESSORIES Inspections and Tests § 18.60 Detailed inspection...

  7. 46 CFR 56.75-30 - Pipe joining details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Pipe joining details. 56.75-30 Section 56.75-30 Shipping... APPURTENANCES Brazing § 56.75-30 Pipe joining details. (a) Silver brazing. (1) Circumferential pipe joints may...) Copper-alloy brazing. (1) Copper-alloy brazing may be employed to join pipe, valves, and...

  8. 46 CFR 195.03-1 - Installation and details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Marine Engineering Systems § 195.03-1 Installation and details. (a) The installation of all systems of a marine engineering nature, together with the details of... (Marine Engineering) of this chapter. Systems of this type include the following: Steering Systems....

  9. South entrance, plan, section, & detail. San Bernardino Valley Union ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    South entrance, plan, section, & detail. San Bernardino Valley Union Junior College, Science Building. Detailed drawings of tile work, wrought iron, and art stone, Howard E. Jones, Architect, San Bernardino, California. Sheet 6, job no. 311. Scale 1.2 inch to the foot. February 15, 1927. - San Bernardino Valley College, Life Science Building, 701 South Mount Vernon Avenue, San Bernardino, San Bernardino County, CA

  10. 5 CFR 352.306 - Length of details.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Length of details. 352.306 Section 352.306 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS REEMPLOYMENT RIGHTS Detail and Transfer of Federal Employees to International Organizations § 352.306 Length...

  11. 46 CFR 113.37-10 - Detailed requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Detailed requirements. 113.37-10 Section 113.37-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING COMMUNICATION AND ALARM SYSTEMS AND EQUIPMENT Shaft Speed and Thrust Indicators § 113.37-10 Detailed requirements. (a) Each indicator must be independent of...

  12. 27. Old Crosscut Canal, Details for Drop Structures at Van ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    27. Old Crosscut Canal, Details for Drop Structures at Van Buren Street and McDowell Road, Wingwall Footing Plan and Pipe Detail, February 1975. Source: City of Phoenix Engineering Department. - Old Crosscut Canal, North Side of Salt River, Phoenix, Maricopa County, AZ

  13. 5 CFR 370.107 - Details to small business concerns.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 5 Administrative Personnel 1 2014-01-01 2014-01-01 false Details to small business concerns. 370.107 Section 370.107 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS INFORMATION TECHNOLOGY EXCHANGE PROGRAM § 370.107 Details to small business concerns. (a) The head of...

  14. 5 CFR 370.107 - Details to small business concerns.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 5 Administrative Personnel 1 2013-01-01 2013-01-01 false Details to small business concerns. 370.107 Section 370.107 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS INFORMATION TECHNOLOGY EXCHANGE PROGRAM § 370.107 Details to small business concerns. (a) The head of each agency must take such actions as may...

  15. 5 CFR 370.107 - Details to small business concerns.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 5 Administrative Personnel 1 2012-01-01 2012-01-01 false Details to small business concerns. 370.107 Section 370.107 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS INFORMATION TECHNOLOGY EXCHANGE PROGRAM § 370.107 Details to small business concerns. (a) The head of...

  16. Space Telecommunications Radio System (STRS) Architecture, Tutorial Part 2 - Detailed

    NASA Technical Reports Server (NTRS)

    Handler, Louis

    2014-01-01

    The STRS architecture detail presentation presents each requirement in the STRS Architecture Standard with some examples and supporting information. The purpose is to give a platform provider, application provider, or application integrator a better, more detailed understanding of the STRS Architecture Standard and its use.

  17. 5 CFR 352.903 - Effecting a detail or transfer.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 5 Administrative Personnel 1 2013-01-01 2013-01-01 false Effecting a detail or transfer. 352.903 Section 352.903 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS REEMPLOYMENT RIGHTS Reemployment Rights After Service With the Panama Canal Commission § 352.903 Effecting a detail or transfer. (a) Authority to...

  18. 10. Photocopy of Miscellaneous Details drawing showing door, window, louvre, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    10. Photocopy of Miscellaneous Details drawing showing door, window, louvre, stairway, roof and other detailing (from the BPA Engineering Vault, Drawing C13-J2-342-D1, Sheet 4, 13 March 1939) - Bonneville Power Administration South Bank Substation, I-84, South of Bonneville Dam Powerhouse, Bonneville, Multnomah County, OR

  19. 169. ARAIV Miscellaneous site details, including contaminated waste tank pit, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    169. ARA-IV Miscellaneous site details, including contaminated waste tank pit, fence detail, marker posts, berm, and "Caution radiation hazard" sign. Norman Engineering Company 961-area/ML-1-1-501-3. Date: March 1960. Ineel index code no. 066-0501-00-613-102795. - Idaho National Engineering Laboratory, Army Reactors Experimental Area, Scoville, Butte County, ID

  20. Detail view of portal and storefront entrance at First Street ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail view of portal and storefront entrance at First Street facade. Note flush recessed panels above transom lights; a historic photograph portrays elaborate detail in these exterior panels. Beginning on inscription "Post Office Arcade" appears at right; this panel is covered by a sign reading "Collier Arcade" on the Broadway facade - Post Office Arcade, 2118 First Street, Fort Myers, Lee County, FL

  1. Initial detailed designs for intermediate photovoltaic systems: Office building

    NASA Astrophysics Data System (ADS)

    Herz, J.; Obrien, G.

    1982-07-01

    A detailed design is presented for a 140 kW ground mounted flat plate array photovoltaic system to serve a three story office building. The design is analyzed for performance and economics. Building architectural features and load demands are defined. Photovoltaic array, electrical system design, and system installation are discussed, along with alternative design choices. Specifications and installation details are included.

  2. Initial detailed designs for intermediate photovoltaic systems: Branch bank

    NASA Astrophysics Data System (ADS)

    Obrien, G.; Herz, J.

    1981-12-01

    The first of four detailed PV system designs for intermediate applications with a peak electrical load of 20 to 500 kW is presented. The initial design for a 6 kW direct roof mount, fixed tilt, flat plate array is analyzed for performance and economics. A drawing set, specifications, and installation details are included for procurement and construction bids.

  3. 35. DETAILS AND SECTIONS OF FUEL ELEMENT SUPPORT PLATFORM, FUEL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    35. DETAILS AND SECTIONS OF FUEL ELEMENT SUPPORT PLATFORM, FUEL ELEMENT HOLDER, TRIP MECHANISM COVER, AND OTHER DETAILS. F.C. TORKELSON DRAWING NUMBER 842-ARVFS-701-S-3. INEL INDEX CODE NUMBER: 075 0701 60 851 151977. - Idaho National Engineering Laboratory, Advanced Reentry Vehicle Fusing System, Scoville, Butte County, ID

  4. 5 CFR 370.107 - Details to small business concerns.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 5 Administrative Personnel 1 2011-01-01 2011-01-01 false Details to small business concerns. 370... INFORMATION TECHNOLOGY EXCHANGE PROGRAM § 370.107 Details to small business concerns. (a) The head of each... organizations in each calendar year, at least 20 percent are to small business concerns, in accordance with 5...

  5. 46 CFR 42.13-40 - Details of marking.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Details of marking. 42.13-40 Section 42.13-40 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES DOMESTIC AND FOREIGN VOYAGES BY SEA General Rules for Determining Load Lines § 42.13-40 Details of marking. (a) The ring, lines and...

  6. 46 CFR 70.20-1 - Marine engineering details.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 3 2013-10-01 2013-10-01 false Marine engineering details. 70.20-1 Section 70.20-1... General Marine Engineering Requirements § 70.20-1 Marine engineering details. All marine engineering... subchapter F (Marine Engineering) of this chapter....

  7. 46 CFR 70.20-1 - Marine engineering details.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 3 2012-10-01 2012-10-01 false Marine engineering details. 70.20-1 Section 70.20-1... General Marine Engineering Requirements § 70.20-1 Marine engineering details. All marine engineering... subchapter F (Marine Engineering) of this chapter....

  8. 46 CFR 70.20-1 - Marine engineering details.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 3 2011-10-01 2011-10-01 false Marine engineering details. 70.20-1 Section 70.20-1... General Marine Engineering Requirements § 70.20-1 Marine engineering details. All marine engineering... subchapter F (Marine Engineering) of this chapter....

  9. 46 CFR 70.20-1 - Marine engineering details.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 3 2014-10-01 2014-10-01 false Marine engineering details. 70.20-1 Section 70.20-1... General Marine Engineering Requirements § 70.20-1 Marine engineering details. All marine engineering... subchapter F (Marine Engineering) of this chapter....

  10. Monte Carlo simulation of the effect of focal spot size on contrast-detail detectability.

    PubMed

    Poletti, John; McLean, Donald

    2012-03-01

    A contrast-detail experiment was simulated using Monte Carlo methods, to test the hypothesis that quantum limitations lead to an optimum minimum focal spot size below which no further improvement in image quality may be obtained. The simulation included a variable X-ray tube focal spot size, patient equivalent water phantom, X-ray couch, automatic exposure control, anti-scatter grid and indirect digital radiography detector. A number of simplifications were necessary in order to limit the calculation time to 8 days per image. Four images were produced for each focal spot size and these were scored by eight experienced observers. The contrast-detail curves were found to improve monotonically as focal spot size was reduced, with the best images produced by a point source. This contradicts the hypothesis of quantum limitation of focal spot size. We conclude that further work is required on the optimization of focal spot size. To assist with this, a new definition of system detective quantum efficiency is suggested, that includes the focal spot modulation transfer function, but does not include scattered radiation from the patient. PMID:22143903

  11. OBSERVATIONS OF DETAILED STRUCTURE IN THE SOLAR WIND AT 1 AU WITH STEREO/HI-2

    SciTech Connect

    DeForest, C. E.; Howard, T. A.; Tappin, S. J. E-mail: howard@boulder.swri.edu

    2011-09-01

    We present images of solar wind electron density structures at distances of 1 AU, extracted from the STEREO/HI-2 data. Collecting the images requires separating the Thomson-scattered signal from the other background/foreground sources that are 10{sup 3} times brighter. Using a combination of techniques, we are able to generate calibrated imaging data of the solar wind with sensitivity of a few x 10{sup -17} B{sub sun}, compared to the background signal of a few x 10{sup -13} B{sub sun}, using only the STEREO/HI-2 Level 1 data as input. These images reveal detailed spatial structure in coronal mass ejections (CMEs) and the solar wind at projected solar distances in excess of 1 AU, at the instrumental motion-blur resolution limit of 1{sup 0}-3{sup 0}. CME features visible in the newly reprocessed data from 2008 December include leading-edge pileup, interior voids, filamentary structure, and rear cusps. 'Quiet' solar wind features include V-shaped structures centered on the heliospheric current sheet, plasmoids, and 'puffs' that correspond to the density fluctuations observed in situ. We compare many of these structures with in situ features detected near 1 AU. The reprocessed data demonstrate that it is possible to perform detailed structural analyses of heliospheric features with visible light imagery, at distances from the Sun of at least 1 AU.

  12. Broken detailed balance at mesoscopic scales in active biological systems.

    PubMed

    Battle, Christopher; Broedersz, Chase P; Fakhri, Nikta; Geyer, Veikko F; Howard, Jonathon; Schmidt, Christoph F; MacKintosh, Fred C

    2016-04-29

    Systems in thermodynamic equilibrium are not only characterized by time-independent macroscopic properties, but also satisfy the principle of detailed balance in the transitions between microscopic configurations. Living systems function out of equilibrium and are characterized by directed fluxes through chemical states, which violate detailed balance at the molecular scale. Here we introduce a method to probe for broken detailed balance and demonstrate how such nonequilibrium dynamics are manifest at the mesosopic scale. The periodic beating of an isolated flagellum from Chlamydomonas reinhardtii exhibits probability flux in the phase space of shapes. With a model, we show how the breaking of detailed balance can also be quantified in stationary, nonequilibrium stochastic systems in the absence of periodic motion. We further demonstrate such broken detailed balance in the nonperiodic fluctuations of primary cilia of epithelial cells. Our analysis provides a general tool to identify nonequilibrium dynamics in cells and tissues. PMID:27126047

  13. Detail of Ganymede's Uruk Sulcus Region as Viewed by Galileo and Voyager

    NASA Technical Reports Server (NTRS)

    1996-01-01

    View of the region of Ganymede's Uruk Sulcus placed on a lower resolution Voyager view taken 17 years earlier. North is to the top of the picture and the sun illuminates the surface from almost overhead in the Galileo view. The finest details that can be discerned in the Galileo picture are about 80 meters across. The four boxes outlined in white show the extent of Galileo's initial look at this area. The Jet Propulsion Laboratory, Pasadena, CA manages the mission for NASA's Office of Space Science, Washington, DC. This image and other images and data received from Galileo are posted on the World Wide Web, on the Galileo mission home page at URL http://galileo.jpl.nasa.gov. Background information and educational context for the images can be found at URL http://www.jpl.nasa.gov/galileo/sepo

  14. Contrast to Noise Ratio and Contrast Detail Analysis in Mammography:A Monte Carlo Study

    NASA Astrophysics Data System (ADS)

    Metaxas, V.; Delis, H.; Kalogeropoulou, C.; Zampakis, P.; Panayiotakis, G.

    2015-09-01

    The mammographic spectrum is one of the major factors affecting image quality in mammography. In this study, a Monte Carlo (MC) simulation model was used to evaluate image quality characteristics of various mammographic spectra. The anode/filter combinations evaluated, were those traditionally used in mammography, for tube voltages between 26 and 30 kVp. The imaging performance was investigated in terms of Contrast to Noise Ratio (CNR) and Contrast Detail (CD) analysis, by involving human observers, utilizing a mathematical CD phantom. Soft spectra provided the best characteristics in terms of both CNR and CD scores, while tube voltage had a limited effect. W-anode spectra filtered with k-edge filters demonstrated an improved performance, that sometimes was better compared to softer x-ray spectra, produced by Mo or Rh anode. Regarding the filter material, k-edge filters showed superior performance compared to Al filters.

  15. Detailed Northern Anatolian Fault Zone crustal structure from receiver functions

    NASA Astrophysics Data System (ADS)

    Cornwell, D. G.; Kahraman, M.; Thompson, D. A.; Houseman, G. A.; Rost, S.; Turkelli, N.; Teoman, U.; Altuncu Poyraz, S.; Gülen, L.; Utkucu, M.

    2013-12-01

    locations at either of the NAFZ fault branches. We observe first-order differences in crustal structure between the crustal blocks that are separated by the faults. Each crustal block also contains regions of strong anisotropy at various depths that will be analyzed further with the full seismological dataset and compared to petrofabric analyses of exhumed fault segments. We will compare our results with other seismological imaging techniques to attempt to resolve the distribution of fault zone deformation with respect to depth. This information will be useful to other complementary Faultlab techniques that will add a detailed insight into the fault structure and dynamics of the NAFZ and contribute more broadly into ongoing research into major strike-slip fault zones.

  16. Passive athermalization of doublets in 8-13 micron waveband

    NASA Astrophysics Data System (ADS)

    Schuster, Norbert

    2014-10-01

    Passive athermalization of lenses has become a key-technology for automotive and other outdoor applications using modern uncooled 25, 17 and 12 micron pixel pitch bolometer arrays. Typical pixel counts for thermal imaging are 384x288 (qVGA), 640x480 (VGA), and 1024x768 (XGA). Two lens arrangements (called Doublets) represent a cost effective way to satisfy resolution requirements of these detectors with F-numbers 1.4 or faster. Thermal drift of index of refraction and the geometrical changes (in lenses and housing) versus temperature defocus the initial image plane from the detector plane. The passive athermalization restricts this drop of spatial resolution in a wide temperature range (typically -40°C…+80°C) to an acceptable value without any additional external refocus. In particular, lenses with long focal lengths and high apertures claim athermalization. A careful choice of lens and housing materials and a sophistical dimensioning lead to three different principles of passivation: The Passive Mechanical Athermalization (PMA) shifts the complete lens cell, the Passive Optical and Mechanical Athermalization (POMA) shifts only one lens inside the housing, the Passive Optical Athermalization (POA) works without any mechanism. All three principles will be demonstrated for a typical narrow-field lens (HFOV about 12°) with high aperture (aperture based F-number 1.3) for the actual uncooled reference detector (17micron VGA). Six design examples using different combinations of lens materials show the impact on spatial lens resolution, on overall length, and on weight. First order relations are discussed. They give some hints for optimization solutions. Pros and cons of different passive athermalization principles are evaluated in regards of housing design, availability of materials and costing. Examples with a convergent GASIR®1-lens in front distinguish by best resolution, short overall length, and lowest weight.

  17. Characterization of InGaAs-based cameras for astronomical applications using a new VIS-NIR-SWIR detector test bench

    NASA Astrophysics Data System (ADS)

    Schindler, Karsten; Wolf, Jürgen; Krabbe, Alfred

    2014-07-01

    A new test bench for detector and camera characterization in the visible and near-infrared spectral range between 350 -2500 nm has been setup at the Max Planck Institute for Solar System Research (MPS). The detector under study is illuminated by an integrating sphere that is fed by a Czerny-Turner monochromator with quasi-monochromatic light. A quartz tungsten halogen lamp is used as a light source for the monochromator. Si- and InGaAs-based photodiodes have been calibrated against secondary reference standards at PTB (Germany), NPL (UK) and NRC (Canada) for precise spectral flux measurements. The test bench allows measurements of fundamental detector properties such as linearity of response, conversion gain, full well capacity, quantum efficiency (QE), fixed pattern noise and pixel response non-uniformity. The article will focus on the commissioning of the test bench and subsequent performance evaluation and characterization of a commercial camera system with a 640 x 480 InGaAs-detector, sensitive between 900 to 1650 nm. The study aimed at the potential use of InGaAs cameras in ground-based and airborne astronomical observations or as target acquisition and tracking cameras in the NIR supporting infrared observations at longer wavelengths, e.g. on SOFIA. An intended future application of the test bench in combination with an appropriate test dewar is the characterization of focal plane assemblies for imaging spectrometers on spacecraft missions, such as the VIS-SWIR channel of MAJIS, the Moons and Jupiter Imaging Spectrometer aboard JUICE (Jupiter Icy Moons Explorer).

  18. Dynamic Isosurface Extraction and Level-of-Detail in Voxel Space

    SciTech Connect

    Lamphere, P.B.; Linebarger, J.M.

    1999-03-01

    A new visualization representation is described, which dramatically improves interactivity for scientific visualizations of structured grid data sets by creating isosurfaces at interactive speeds and with dynamically changeable levels-of-detail (LOD). This representation enables greater interactivity by allowing an analyst to dynamically specify both the desired isosurface threshold and required level-of-detail to be used while rendering the image. A scientist can therefore view very large isosurfaces at interactive speeds (with a low level-of-detail), but has the full data set always available for analysis. The key idea is that various levels-of-detail are represented as differently sized hexahedral virtual voxels, which are stored in a three-dimensional binary tree, or kd-tree; thus the level-of-detail representation is done in voxel space instead of the traditional approach which relies on surface or geometry space decimations. Utilizing the voxel space is an essential step to moving from a post-processing visualization paradigm to a quantitative, real-time paradigm. This algorithm has been implemented as an integral component of the EIGEN/VR project at Sandia National Laboratories, which provides a rich environment for scientists to interactively explore and visualize the results of very large-scale simulations performed on massively parallel supercomputers.

  19. Detailed Velocity and Density models of the Cascadia Subduction Zone from Prestack Full-Waveform Inversion

    NASA Astrophysics Data System (ADS)

    Fortin, W.; Holbrook, W. S.; Mallick, S.; Everson, E. D.; Tobin, H. J.; Keranen, K. M.

    2014-12-01

    Understanding the geologic composition of the Cascadia Subduction Zone (CSZ) is critically important in assessing seismic hazards in the Pacific Northwest. Despite being a potential earthquake and tsunami threat to millions of people, key details of the structure and fault mechanisms remain poorly understood in the CSZ. In particular, the position and character of the subduction interface remains elusive due to its relative aseismicity and low seismic reflectivity, making imaging difficult for both passive and active source methods. Modern active-source reflection seismic data acquired as part of the COAST project in 2012 provide an opportunity to study the transition from the Cascadia basin, across the deformation front, and into the accretionary prism. Coupled with advances in seismic inversion methods, this new data allow us to produce detailed velocity models of the CSZ and accurate pre-stack depth migrations for studying geologic structure. While still computationally expensive, current computing clusters can perform seismic inversions at resolutions that match that of the seismic image itself. Here we present pre-stack full waveform inversions of the central seismic line of the COAST survey offshore Washington state. The resultant velocity model is produced by inversion at every CMP location, 6.25 m laterally, with vertical resolution of 0.2 times the dominant seismic frequency. We report a good average correlation value above 0.8 across the entire seismic line, determined by comparing synthetic gathers to the real pre-stack gathers. These detailed velocity models, both Vp and Vs, along with the density model, are a necessary step toward a detailed porosity cross section to be used to determine the role of fluids in the CSZ. Additionally, the P-velocity model is used to produce a pre-stack depth migration image of the CSZ.

  20. Investigating the Interaction of Graphic Organizers and Seductive Details: Can a Graphic Organizer Mitigate the Seductive-Details Effect?

    ERIC Educational Resources Information Center

    Rowland-Bryant, Emily; Skinner, Christopher H.; Skinner, Amy L.; Saudargas, Richard; Robinson, Daniel H.; Kirk, Emily R.

    2009-01-01

    The interaction between seductive details (SD) and a graphic organizer (GO) was investigated. Undergraduate students (n = 207) read a target-material passage about Freud's psychosexual stages. Depending on condition, the participants also read a biographical paragraph (SD-only), viewed a graphic organizer that linked the seductive details to the…

  1. Recovering and Preventing Loss of Detailed Memory: Differential Rates of Forgetting for Detail Types in Episodic Memory

    ERIC Educational Resources Information Center

    Sekeres, Melanie J.; Bonasia, Kyra; St-Laurent, Marie; Pishdadian, Sara; Winocur, Gordon; Grady, Cheryl; Moscovitch, Morris

    2016-01-01

    Episodic memories undergo qualitative changes with time, but little is known about how different aspects of memory are affected. Different types of information in a memory, such as perceptual detail, and central themes, may be lost at different rates. In patients with medial temporal lobe damage, memory for perceptual details is severely impaired,…

  2. Slot scanning versus antiscatter grid in digital mammography: comparison of low-contrast performance using contrast-detail measurement

    NASA Astrophysics Data System (ADS)

    Lai, Chao-Jen; Shaw, Chris C.; Geiser, William; Kappadath, Srinivas C.; Liu, Xinming; Wang, TianPeng; Tu, Shu-Ju; Altunbas, Mustafa C.

    2004-05-01

    Slot scanning imaging techniques allow for effective scatter rejection without attenuating primary x-rays. The use of these techniques should generate better image quality for the same mean glandular dose (MGD) or a similar image quality for a lower MGD as compared to imaging techniques using an anti-scatter grid. In this study, we compared a slot scanning digital mammography system (SenoScan, Fisher Imaging Systems, Denver, CO) to a full-field digital mammography (FFDM) system used in conjunction with a 5:1 anti-scatter grid (SenoGraphe 2000D, General Electric Medical Systems, Milwaukee, WI). Images of a contrast-detail phantom (University Hospital Nijmegen, The Netherlands) were reviewed to measure the contrast-detail curves for both systems. These curves were measured at 100%, 71%, 49% and 33% of the reference mean glandular dose (MGD), as determined by photo-timing, for the Fisher system and 100% for the GE system. Soft-copy reading was performed on review workstations provided by the manufacturers. The correct observation ratios (CORs) were also computed and used to compare the performance of the two systems. The results showed that, based on the contrast-detail curves, the performance of the Fisher images, acquired at 100% and 71% of the reference MGD, was comparable to the GE images at 100% of the reference MGD. The CORs for Fisher images were 0.463 and 0.444 at 100% and 71% of the reference MGD, respectively, compared to 0.453 for the GE images at 100% of the reference MGD.

  3. The 2006 lava dome eruption of Merapi Volcano (Indonesia): Detailed analysis using MODIS TIR

    NASA Astrophysics Data System (ADS)

    Carr, Brett B.; Clarke, Amanda B.; Vanderkluysen, Loÿc

    2016-02-01

    Merapi is one of Indonesia's most active and dangerous volcanoes. Prior to the 2010 VEI 4 eruption, activity at Merapi during the 20th century was characterized by the growth and collapse of a series of lava domes. Periods of very slow growth were punctuated by short episodes of increased eruption rates characterized by dome collapse-generated pyroclastic density currents (PDCs). An eruptive event of this type occurred in May-June, 2006. For effusive eruptions such as this, detailed extrusion rate records are important for understanding the processes driving the eruption and the hazards presented by the eruption. We use thermal infrared (TIR) images from the Moderate Resolution Imaging Spectrometer (MODIS) instrument on NASA's Aqua and Terra satellites to estimate extrusion rates at Merapi Volcano during the 2006 eruption using the method of Harris and Ripepe (2007). We compile a set of 75 nighttime MODIS images of the eruptive period to produce a detailed time series of thermal radiance and extrusion rate that reveal multiple phases of the 2006 eruption. These data closely correspond to the published ground-based observational record and improve observation density and detail during the eruption sequence. Furthermore, additional analysis of radiance values for thermal anomalies in Band 21 (λ = 3.959 μm) of MODIS images results in a new framework for detecting different styles of activity. We successfully discriminate among slow dome growth, rapid dome growth, and PDC-producing dome collapse. We also demonstrate a positive correlation between PDC frequency and extrusion rate, and provide evidence that extrusion rate can increase in response to external events such as dome collapses or tectonic earthquakes. This study represents a new method of documenting volcanic activity that can be applied to other similar volcanic systems.

  4. Detailed black hole state counting in loop quantum gravity

    SciTech Connect

    Agullo, Ivan; Barbero G, J. Fernando; Borja, Enrique F.; Diaz-Polo, Jacobo; Villasenor, Eduardo J. S.

    2010-10-15

    We give a complete and detailed description of the computation of black hole entropy in loop quantum gravity by employing the most recently introduced number-theoretic and combinatorial methods. The use of these techniques allows us to perform a detailed analysis of the precise structure of the entropy spectrum for small black holes, showing some relevant features that were not discernible in previous computations. The ability to manipulate and understand the spectrum up to the level of detail that we describe in the paper is a crucial step toward obtaining the behavior of entropy in the asymptotic (large horizon area) regime.

  5. A detailed gravimetric geoid from North America to Eurasia

    NASA Technical Reports Server (NTRS)

    Vincent, S. F.; Strange, W. E.; Marsh, J. G.

    1972-01-01

    A detailed gravimetric geoid of the United States, North Atlantic, and Eurasia, which was computed from a combination of satellite derived and surface gravity data, is presented. The precision of this detailed geoid is + or - 2 to + or - 3 m in the continents but may be in the range of 5 to 7 m in those areas where data is sparse. Comparisons of the detailed gravimetric geoid with results of Rapp, Fischer, and Rice for the United States, Bomford in Europe, and Heiskanen and Fischer in India are presented. Comparisons are also presented with geoid heights from satellite solutions for geocentric station coordinates in North America, the Caribbean, and Europe.

  6. Large Terrain Continuous Level of Detail 3D Visualization Tool

    NASA Technical Reports Server (NTRS)

    Myint, Steven; Jain, Abhinandan

    2012-01-01

    This software solved the problem of displaying terrains that are usually too large to be displayed on standard workstations in real time. The software can visualize terrain data sets composed of billions of vertices, and can display these data sets at greater than 30 frames per second. The Large Terrain Continuous Level of Detail 3D Visualization Tool allows large terrains, which can be composed of billions of vertices, to be visualized in real time. It utilizes a continuous level of detail technique called clipmapping to support this. It offloads much of the work involved in breaking up the terrain into levels of details onto the GPU (graphics processing unit) for faster processing.

  7. Chandra and XMM View Galaxy Groups: New Details from Sharper Images

    NASA Astrophysics Data System (ADS)

    Vrtilek, J. M.; Ponman, T. J.; O'Sullivan, E. J.; David, L. P.; Harris, D. E.; Forman, W.; Jones, C.; Lane, W. M.; Kassim, N. E.

    2004-08-01

    Groups and poor clusters are the locus of most galaxies in the present-day Universe and the building blocks from which clusters form. They accordingly occupy a significant place in the continuum of structure between isolated galaxies and rich clusters. Owing to the lower temperature of their intracluster gas, X-ray emission from groups produces strong lines from a broader range of elements than do hotter clusters. Here we show results from an examination of several X-ray bright groups, mostly from the Hickson, AWM, and MKW lists, relevant to issues of current interest in the study of both groups and clusters: the distribution of heavy elements, the presence and nature of X-ray cavities and their relation to radio observations, the presence of cooling cores, and X-ray signatures of recent galaxy interactions. This work was supported in part by NASA grants GO2-3186X and GO4-5154X.

  8. Diagnostic imaging of infertility

    SciTech Connect

    Winfield, A.C.; Wentz, A.C.

    1987-01-01

    This text presents a review of all the imaging modalities available in the diagnosis of infertility. This book integrates the perspectives of experts in ob/gyn, radiology, reproductive endocrinology, and urology. It's a one-of-a-kind ''how to'' guide to hysterosalpinography and infertility evaluation, providing complete clinical information on the techniques, pitfalls, problems encountered and differential diagnosis. Detailed descriptions accompany numerous high-quality illustrations to help correlate findings and give meaning to the radiographic and ultrasound images.

  9. Cardiac imaging in adults

    SciTech Connect

    Jaffe, C.C.

    1987-01-01

    This book approaches adult cardiac disease from the correlative imaging perspective. It includes chest X-rays and angiographs, 2-dimensional echocardiograms with explanatory diagrams for clarity, plus details on digital radiology, nuclear medicine techniques, CT and MRI. It also covers the normal heart, valvular heart disease, myocardial disease, pericardial disease, bacterial endocarditis, aortic aneurysm, cardiac tumors, and congenital heart disease of the adult. It points out those aspects where one imaging technique has significant superiority.

  10. Meteorological image processing applications

    NASA Technical Reports Server (NTRS)

    Bracken, P. A.; Dalton, J. T.; Hasler, A. F.; Adler, R. F.

    1979-01-01

    Meteorologists at NASA's Goddard Space Flight Center are conducting an extensive program of research in weather and climate related phenomena. This paper focuses on meteorological image processing applications directed toward gaining a detailed understanding of severe weather phenomena. In addition, the paper discusses the ground data handling and image processing systems used at the Goddard Space Flight Center to support severe weather research activities and describes three specific meteorological studies which utilized these facilities.

  11. VLA's Sharpened Vision Shows Details of Still-Forming Star

    NASA Astrophysics Data System (ADS)

    2001-01-01

    Using a new observing capability of the National Science Foundation's Very Large Array (VLA) radio telescope, astronomers have discovered a solar-system-sized disk of gas and dust feeding material onto a young star with 8 to 10 times the mass of the Sun. This is the first time an inner "accretion disk" has been seen around such a massive star. The VLA images also revealed the inner portion of an energetic outflow of material powered by the accretion disk. Artist's conception "Disks and outflows in young stars increase dramatically in mass and energy as the mass of the young star increases. We don't know if the same process is at work in all young stars or how the disks can both power an outflow that extends more than 15 light-years and also start the process of forming planets," said Debra Shepherd, of the National Radio Astronomy Observatory (NRAO) in Socorro, New Mexico. "By studying the birth of massive young stars, we're pushing the limits of our understanding and trying to learn if there are critical differences between the outflows from high and low mass young stars," she added Shepherd and Mark Claussen, also from the NRAO in Socorro, and Stan Kurtz of the National Autonomous University in Mexico, presented their findings today at the American Astronomical Society's meeting in San Diego, CA. The scientists made the discovery using the VLA connected by a newly- operational fiber-optic link to one of the radio-telescope antennas of the NSF's Very Long Baseline Array (VLBA), located at Pie Town, NM, 32 miles away from the VLA. Linking the VLA to the Pie Town antenna almost doubled the resolving power, or ability to see fine detail, available to the astronomers. "We could not have seen these structures without using the Pie Town antenna connected to the VLA," said Claussen. Work on the VLA-Pie Town fiber-optic link, financed by the NSF and Associated Universities, Inc., which operates NRAO for the NSF, began in late 1997. The linked facilities first were

  12. 3. DETAIL VIEW OF DIRECT DRIVE STERLING 'DOLPHIN T' MODEL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. DETAIL VIEW OF DIRECT DRIVE STERLING 'DOLPHIN T' MODEL 4 CYLINDER, GASOLINE TRACTOR-TYPE ENGINE WITH FALKBIBBY FLEXIBLE COUPLING - Central Railroad of New Jersey, Newark Bay Lift Bridge, Spanning Newark Bay, Newark, Essex County, NJ

  13. Facility 596, detail of ramp from below, with replacement sheetpile ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Facility 596, detail of ramp from below, with replacement sheet-pile dolphin on right and southernmost dolphins in background. - U.S. Naval Base, Pearl Harbor, Ferry Landing Type, Halawa Landing on Ford Island, Pearl City, Honolulu County, HI

  14. 8. DETAIL VIEW OF INCLINED OUTLET GATE WHEEL, LOOKING EAST ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    8. DETAIL VIEW OF INCLINED OUTLET GATE WHEEL, LOOKING EAST - High Mountain Dams in Upalco Unit, Kidney Lake Dam, Ashley National Forest, 4.7 miles North of Miners Gulch Campground, Mountain Home, Duchesne County, UT

  15. 8. Detail of underside of bridge deck, from the southern ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    8. Detail of underside of bridge deck, from the southern end looking toward north-northwest. - Bridge No. 4800, Spanning Minnesota River on Trunk Highway 4 between Brown & Nicollet Counties, Sleepy Eye, Brown County, MN

  16. 214. Frank Deras Jr., Photographer May 1998 DETAIL VIEW OF ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    214. Frank Deras Jr., Photographer May 1998 DETAIL VIEW OF STRAND SHOES, EYE BARS, AND CONCRETE ABUTMENT IN YERBA BUENA ANCHORAGE, FACING SOUTHEAST. - San Francisco Oakland Bay Bridge, Spanning San Francisco Bay, San Francisco, San Francisco County, CA

  17. 265. Dennis Hill, Photographer April 1998 DETAIL VIEW OF TENSION ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    265. Dennis Hill, Photographer April 1998 DETAIL VIEW OF TENSION EYE BARS AT CANTILEVER TRUSS, FACING SOUTHWEST. - San Francisco Oakland Bay Bridge, Spanning San Francisco Bay, San Francisco, San Francisco County, CA

  18. 10. Detail of truss located on top the northeast pier, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    10. Detail of truss located on top the northeast pier, looking southwest. - Bridge No. 4800, Spanning Minnesota River on Trunk Highway 4 between Brown & Nicollet Counties, Sleepy Eye, Brown County, MN

  19. 266. Dennis Hill, Photographer June 1998 DETAIL VIEW OF TENSION ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    266. Dennis Hill, Photographer June 1998 DETAIL VIEW OF TENSION EYE BARS AND COMPRESSION MEMBERS ABOVE UPPER DECK, FACING SOUTHEAST. - San Francisco Oakland Bay Bridge, Spanning San Francisco Bay, San Francisco, San Francisco County, CA

  20. DETAIL VIEW OF THE ROCKET TRANSFER CART. NOTE THE VALVE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DETAIL VIEW OF THE ROCKET TRANSFER CART. NOTE THE VALVE BOX IN THE FOREGROUND RIGHT WITH AN EYE WASH FAUCET PROJECTING OUT. - Marshall Space Flight Center, Redstone Rocket (Missile) Test Stand, Dodd Road, Huntsville, Madison County, AL

  1. 10. DETAIL OF JUNCTION BETWEEN LOWER CHORD, VERTICAL LACED CHANNEL, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    10. DETAIL OF JUNCTION BETWEEN LOWER CHORD, VERTICAL LACED CHANNEL, FLOOR BEAM, EYE BAR, AND U-BOLT. WEST ABUTMENT. - River Road Bridge, Spanning Spring Creek in Spring Creek Township, Hallton, Elk County, PA

  2. DETAIL VIEW, OXEYE WINDOW, SOUTH WALL OF SOUTH GARRET. THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DETAIL VIEW, OX-EYE WINDOW, SOUTH WALL OF SOUTH GARRET. THE MUNTIN PATTERN USED IN THIS WINDOW WAS REFERRED TO AS “GOTHIC” IN THE EIGHTEENTH CENTURY - The Woodlands, 4000 Woodlands Avenue, Philadelphia, Philadelphia County, PA

  3. 9. Detail of truss work on southwesternmost span, looking northnortheast ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    9. Detail of truss work on southwesternmost span, looking north-northeast - Bridge No. 4800, Spanning Minnesota River on Trunk Highway 4 between Brown & Nicollet Counties, Sleepy Eye, Brown County, MN

  4. 10. NORTHEAST CORNER CONSTRUCTION DETAIL, VIEW OF SIDEWALK. TAMARACK BRIDGE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    10. NORTHEAST CORNER CONSTRUCTION DETAIL, VIEW OF SIDEWALK. TAMARACK BRIDGE IN LEFT REAR. - Cascade Creek Bridge, Spanning Cascade Creek on New Big Oak Flat Road, Yosemite Village, Mariposa County, CA

  5. 8. DETAIL VIEW, LOOKING NORTHEAST, SHOWING OUTRIGGERS FOR LATERAL BRACING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    8. DETAIL VIEW, LOOKING NORTHEAST, SHOWING OUTRIGGERS FOR LATERAL BRACING FOR TRUSSES AND BOTTOM CHORD CONNECTIONS. - White Bowstring Arch Truss Bridge, Spanning Yellow Creek at Cemetery Drive (Riverside Drive), Poland, Mahoning County, OH

  6. 5. DETAIL VIEW OF TWO PANEL POINTS OF TRUSS, SHOWING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    5. DETAIL VIEW OF TWO PANEL POINTS OF TRUSS, SHOWING OVAL, TUBULAR UPPER CHORD MEMBER, VERTICALS, DIAGONALS, AND LOWER CHORD. - White Bowstring Arch Truss Bridge, Spanning Yellow Creek at Cemetery Drive (Riverside Drive), Poland, Mahoning County, OH

  7. 4. DETAIL VIEW OF STONE MASONRY, WING WALL AND WHAT ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. DETAIL VIEW OF STONE MASONRY, WING WALL AND WHAT REMAINS OF ORIGINAL WALKWAY RAILING. - Main Street Parker Pony Truss Bridge, Main Street (Route 170) spanning Yellow Creek, Poland, Mahoning County, OH

  8. DETAIL VIEW OF SINGLE PANEL POINTS TAKEN FROM BRIDGE DECK, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DETAIL VIEW OF SINGLE PANEL POINTS TAKEN FROM BRIDGE DECK, SHOWING CONNECTION BETWEEN VERTICAL AND UPPER CHORD MEMBER - White Bowstring Arch Truss Bridge, Spanning Yellow Creek at Cemetery Drive (Riverside Drive), Poland, Mahoning County, OH

  9. 9. DETAIL OF UNITEDTOD TWINTANDEM STEAM ENGINE, SHOWING HIGHPRESSURE CYLINDER ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    9. DETAIL OF UNITED-TOD TWIN-TANDEM STEAM ENGINE, SHOWING HIGH-PRESSURE CYLINDER AND EXTENSION OF HOUSING. - Republic Iron & Steel Company, Youngstown Works, Blooming Mill & Blooming Mill Engines, North of Poland Avenue, Youngstown, Mahoning County, OH

  10. 6. DETAIL VIEW OF SINGLE PANEL POINTS TAKEN FROM BRIDGE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    6. DETAIL VIEW OF SINGLE PANEL POINTS TAKEN FROM BRIDGE DECK, SHOWING CONNECTION BETWEEN VERTICAL AND UPPER CHORD MEMBER. - White Bowstring Arch Truss Bridge, Spanning Yellow Creek at Cemetery Drive (Riverside Drive), Poland, Mahoning County, OH

  11. 46 CFR 195.05-1 - Installation and details.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... interior communication nature, together with the details of design, construction, and installation shall be... of this type include the following: Ship's Service Generating Systems. Ship's Service Power... Lighting and Power Systems. Electric Lifeboat Winch Systems. Electric Steering Gear and Steering...

  12. 46 CFR 195.05-1 - Installation and details.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... interior communication nature, together with the details of design, construction, and installation shall be... of this type include the following: Ship's Service Generating Systems. Ship's Service Power... Lighting and Power Systems. Electric Lifeboat Winch Systems. Electric Steering Gear and Steering...

  13. 46 CFR 96.05-1 - Installation and details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... interior communication nature, together with the details of design, construction, and installation, shall.... Systems of this type include the following: Ship's service generating systems. Ship's service power... lighting and power systems. Electric lifeboat winch systems. Electric steering gear and steering...

  14. 46 CFR 77.05-1 - Installation and details.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... communications nature, together with the details of design, construction, and installation, shall be in... type include the following: Ship's service generating systems. Ship's service power distribution... and power systems. Electric lifeboat winch systems. Electric steering gear and steering...

  15. 46 CFR 77.05-1 - Installation and details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... communications nature, together with the details of design, construction, and installation, shall be in... type include the following: Ship's service generating systems. Ship's service power distribution... and power systems. Electric lifeboat winch systems. Electric steering gear and steering...

  16. 46 CFR 195.05-1 - Installation and details.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... interior communication nature, together with the details of design, construction, and installation shall be... of this type include the following: Ship's Service Generating Systems. Ship's Service Power... Lighting and Power Systems. Electric Lifeboat Winch Systems. Electric Steering Gear and Steering...

  17. 46 CFR 96.05-1 - Installation and details.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... interior communication nature, together with the details of design, construction, and installation, shall.... Systems of this type include the following: Ship's service generating systems. Ship's service power... lighting and power systems. Electric lifeboat winch systems. Electric steering gear and steering...

  18. 46 CFR 77.05-1 - Installation and details.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... communications nature, together with the details of design, construction, and installation, shall be in... type include the following: Ship's service generating systems. Ship's service power distribution... and power systems. Electric lifeboat winch systems. Electric steering gear and steering...

  19. 46 CFR 195.05-1 - Installation and details.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... interior communication nature, together with the details of design, construction, and installation shall be... of this type include the following: Ship's Service Generating Systems. Ship's Service Power... Lighting and Power Systems. Electric Lifeboat Winch Systems. Electric Steering Gear and Steering...

  20. 46 CFR 96.05-1 - Installation and details.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... interior communication nature, together with the details of design, construction, and installation, shall.... Systems of this type include the following: Ship's service generating systems. Ship's service power... lighting and power systems. Electric lifeboat winch systems. Electric steering gear and steering...