Science.gov

Sample records for 6m specification package

  1. Safety analysis report for packaging: the ORNL DOT specification 6M - special form package

    SciTech Connect

    Schaich, R.W.

    1982-07-01

    The ORNL DOT Specification 6M - Special Form Package was fabricated at the Oak Ridge Nation al Laboratory (ORNL) for the transport of Type B solid non-fissile radioactive materials in special form. The package was evaluated on the basis of tests performed by the Dow Chemical Company, Rocky Flats Division, on the DOT-6M container and special form tests performed on a variety of stainless steel capsules at ORNL by Operations Division personnel. The results of these evaluations demonstrate that the package is in compliance with the applicable regulations for the transport of Type B quantities in special form of non-fissile radioactive materials.

  2. AUTHORIZING THE DOT SPECIFICATION 6M PACKAGING FOR CONTINUED USE AT THE SAVANNAH RIVER SITE

    SciTech Connect

    Watkins, R.; Loftin, B.; Hoang, D.

    2010-03-04

    The U.S. Department of Transportation (DOT) Specification 6M packaging was in extensive use for more than 40 years for in-commerce shipments of Type B quantities of fissile and radioactive material (RAM) across the USA, among the Department of Energy (DOE) laboratories, and between facilities in the DOE production complex. In January 2004, the DOT Research and Special Programs Administration (RSPA) Agency issued a final rule in the Federal Register to ammend requirements in the Hazardous Materials Regulations (HMR) pertaining to the transportation of radioactive materials. The final rule became effective on October 1, 2004. One of those changes discontinued the use of the DOT specification 6M, along with other DOT specification packagings, on October 1, 2008. A main driver for the change was due to the fact that 6M specification packagings were not supported by a Safety Analysis Report for Packagings (SARP) that was compliant with Title 10 of the Code of Federal Regulations (CFR) Part 71 (10 CFR 71). The regulatory rules for the discontinued use have been edited in Title 49 of the CFR Parts 100-185, 2004 edition and thereafter. Prior to October 1, 2008, the use of the 6M within the boundaries of the Savannah River Site (SRS), called an onsite transfer, was governed by an onsite transportation document that referenced 49 CFR Parts 100-185. SRS had to develop an Onsite Safety Assessment (OSA) which was independent of 49 CFR in order to justify the continued use of the DOT Specification 6M for the transfer of radioactive material (RAM) at the SRS after October 1, 2008. This paper will discuss the methodology for and difficulties associated with authorizing the DOT Specification 6M Packaging for continued use at the Savannah River Site.

  3. Safety analysis report for packaging: the ORNL DOT specification 6M - tritium trap package. [Tritium absorbed as solid uranium tritide in depleted uranium trap

    SciTech Connect

    DeVore, J.R.

    1984-04-01

    The ORNL DOT Specification 6M--Tritium Trap Package was fabricated at the Oak Ridge National Laboratory (ORNL) for the transport of Type B quantities of tritium as solid uranium tritide. The package was evaluated on the basis of tests performed by the Dow Chemical Company, Rocky Flats Division, on the DOT-6M container, a drop test performed by the ORNL Operations Division, and International Atomic Energy Agency (IAEA) approvals on a similar tritium transport container. The results of these evaluations demonstrate that the package is in compliance with the applicable regulations for the transport of Type B quantities of tritium. 4 references, 8 figures.

  4. Operational guidance for using DOT-6M/2R packaging

    SciTech Connect

    Kelly, D.L.; Hummer, J.H.

    1994-03-01

    The purpose of this paper is to describe a new US Department of Energy (DOE), Transportation Management Division task to create a US Department of Transportation (DOT) Specification 6M/2R packaging configuration user`s guide. The need for a user`s guide was identified because the DOT-6M/2R packaging configuration is widely used by DOE site contractors, and DOE receives many questions about the approved packaging configurations. Currently, two DOE organizations have the authority to approve new DOT-6M/2R configurations. For Defense Programs, the Transportation and Packaging Safety Division (EH-332) administers the program. For Environmental Restoration and Waste Management, the Transportation Management Division (EM-261) administers the program.

  5. A review of the safety features of 6M packagings for DOE programs

    SciTech Connect

    Not Available

    1988-12-01

    This report, prepared by a US Department of Energy (DOE) Task Force and organized for clarity into two-page modules, argues that the US Department of Transportation (DOT) Specification-6M packagings (hereafter referred to as 6M packaging, or simply 6M) merit continued DOE use and, if necessary, DOE certification. This report is designed to address the specific requirements of a Safety Analysis Report for Packaging (SARP). While not a SARP, this report constitutes a compilation of all available documentation on 6M packagings. The authors individually, and the Task Force collectively, believe their investigation provides justification for the continued use of 6M packagings because they meet criteria for quality assurance and for safety under normal and accident conditions as defined by the US Nuclear Regulatory Commission (NRC) regulations. This report may be used by DOE managers to assist in deliberations on future requirements for 6M packagings as they are required to support DOE programs. For the purpose of ready evaluation, this report includes categorical topics found in Nuclear Regulatory Guide 7.9, the topical guideline for SARPs. The format, however, will (it is hoped) pleasantly surprise customary reader expectations. For, while maintaining categorical headings and subheadings found in SARPs as a skeleton, the Task Force chose to adopt the document design principles developed by Hughes Aircraft in the 1960s, ''Sequential Thematic Organization of Publications'' (STOP). 37 figs.

  6. Gas leak characteristics of inner packaging components used in the D0T-Spec 6M container

    SciTech Connect

    Taylor, J.M.

    1985-09-01

    A test program was conducted by Pacific Northwest Laboratory to determine the gas leak characteristics of metal food pack cans and 2R vessels used to package radioactive material in a D0T 6M specification container. It can be concluded from the tests performed that the inner packaging components (2R vessel, metal product cans) used with a 6M container can be sealed so that they will be gas tight (<10/sup -5/ cc/sec) under elevated temperature and pressure and impact conditions. To maintain gas tight seals under accident conditions, the metal cans must be sealed with a properly adjusted can-sealing machine; the threads of the 2R vessel must be luted with a sealing compound such as a silicone rubber compound; and the metal cans must be protected inside the 2R vessel with spacer plates and impact absorbers. 4 refs., 37 figs.

  7. Radioactive particulate release associated with the DOT specification 6M container under hypothetical accident conditions

    SciTech Connect

    Taylor, J.M.; Raney, P.J.

    1986-02-01

    A testing program was conducted to determine the leakage of depleted uranium dioxide powder (DUO) from the inner containment components of the US Department of Transportation's (DOT) specification 6M container under hypothetical accident conditions. Depleted uranium dioxide was selected as a surrogate for plutonium oxide because of the similarities in the powder characteristics, density and particle size, and because of the special handling and special facilities required for plutonium oxide. The DUO was packaged inside food pack cans in three different configurations inside the 2R vessel of the 6M container. The amount of DUO powder leakage ranged from none detectable (<2 x 10/sup -7/ g) to a high of 1 x 10/sup -3/ g. The combination of gravity, vibration and pressure produced the highest leakage of DUO. Containers that had hermetic seals (leak rates <6 x 10/sup -4/ atm cc/min) did not leak any detectable amount (<2 x 10/sup -7/ g) of DUO under the test conditions. Impact forces had no effect on the leakage of particles with the packaging configurations used. 23 refs., 24 figs., 3 tabs.

  8. Hypothetical accident conditions, free drop and thermal tests: Specification 6M

    SciTech Connect

    Blankenship, R.W.

    1980-05-01

    The 30 gallon Specification 6M shipping container with rolled-top food pack cans as inner containers is evaluated under conditions required by 10 CFR 71.42. One kilogram of depleted uranium as UO/sub 2/ was packaged in each of the inner containers. After completion of a free drop test and a simulated thermal test, the maximum observed leakage of UO/sub 2/ for the following week was 3.2 ..mu..g. This leakage is well below the allowable leakage per week for most plutonium isotopic mixtures. Using the examples provided, any plutonium isotopic mixture can be easily compared with the allowable leakage per week. Test conditions and results are reported.

  9. 16 CFR 1702.12 - Packaging specifications.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Packaging specifications. 1702.12 Section 1702.12 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION POISON PREVENTION PACKAGING ACT OF 1970 REGULATIONS PETITIONS FOR EXEMPTIONS FROM POISON PREVENTION PACKAGING ACT REQUIREMENTS; PETITION...

  10. 16 CFR 1702.12 - Packaging specifications.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Packaging specifications. 1702.12 Section 1702.12 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION POISON PREVENTION PACKAGING ACT OF 1970 REGULATIONS PETITIONS FOR EXEMPTIONS FROM POISON PREVENTION PACKAGING ACT REQUIREMENTS; PETITION...

  11. 16 CFR 1702.12 - Packaging specifications.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Packaging specifications. 1702.12 Section 1702.12 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION POISON PREVENTION PACKAGING ACT OF 1970 REGULATIONS PETITIONS FOR EXEMPTIONS FROM POISON PREVENTION PACKAGING ACT REQUIREMENTS; PETITION...

  12. 16 CFR 1702.12 - Packaging specifications.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Packaging specifications. 1702.12 Section 1702.12 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION POISON PREVENTION PACKAGING ACT OF 1970 REGULATIONS PETITIONS FOR EXEMPTIONS FROM POISON PREVENTION PACKAGING ACT REQUIREMENTS; PETITION...

  13. 16 CFR 1702.12 - Packaging specifications.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Packaging specifications. 1702.12 Section 1702.12 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION POISON PREVENTION PACKAGING ACT OF 1970 REGULATIONS PETITIONS FOR EXEMPTIONS FROM POISON PREVENTION PACKAGING ACT REQUIREMENTS; PETITION...

  14. Engineered waste-package-system design specification

    SciTech Connect

    Not Available

    1983-05-01

    This report documents the waste package performance requirements and geologic and waste form data bases used in developing the conceptual designs for waste packages for salt, tuff, and basalt geologies. The data base reflects the latest geotechnical information on the geologic media of interest. The parameters or characteristics specified primarily cover spent fuel, defense high-level waste, and commercial high-level waste forms. The specification documents the direction taken during the conceptual design activity. A separate design specification will be developed prior to the start of the preliminary design activity.

  15. 78 FR 44894 - Specifications for Packagings

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-25

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Part 178 Specifications for Packagings CFR Correction 0 In Title 49 of the Code of Federal Regulations, Parts 178 to 199, revised as of October 1,...

  16. 49 CFR 173.62 - Specific packaging requirements for explosives.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Specific packaging requirements for explosives... SHIPPERS-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Definitions, Classification and Packaging for Class 1 § 173.62 Specific packaging requirements for explosives. (a) Except as provided in § 173.7...

  17. 76 FR 30551 - Specifications for Packagings

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-26

    ... where the packaging is manufactured and each location where the design qualification tests are conducted...; (6) Description of the packaging design type (e.g. dimensions, materials, closures, thickness, etc... requirements. * * * * * (l) Record retention. Following each design qualification test and each periodic...

  18. PRIDE Surveillance Projects Data Packaging Project Information Package Specification Version 1.1

    SciTech Connect

    Kelleher, D. M.; Shipp, R. L.; Mason, J. D.

    2010-08-31

    Information Package Specification version 1.1 describes an XML document format called an information package that can be used to store information in information management systems and other information archives. An information package consists of package information, the context required to understand and use that information, package metadata that describes the information, and XML signatures that protect the information. The information package described in this specification was designed to store Department of Energy (DOE) and National Nuclear Security Administration (NNSA) information and includes the metadata required for that information: a unique package identifier, information marking that conforms to DOE and NNSA requirements, and access control metadata. It is an implementation of the Open Archival Information System (OAIS) Reference Model archival information package tailored to meet NNSA information storage requirements and designed to be used in the computing environments at the Y-12 National Security Complex and at other NNSA sites.

  19. PRIDE Surveillance Projects Data Packaging Project, Information Package Specification Version 1.0

    SciTech Connect

    Kelleher, D.M.; Shipp, R. L.; Mason, J. D.

    2009-09-28

    This document contains a specification for a standard XML document format called an information package that can be used to store information and the context required to understand and use that information in information management systems and other types of information archives. An information package consists of packaged information, a set of information metadata that describes the packaged information, and an XML signature that protects the packaged information. The information package described in this specification was designed to be used to store Department of Energy (DOE) and National Nuclear Security Administration (NNSA) information and includes the metadata required for that information: a unique package identifier, information marking that conforms to DOE and NNSA requirements, and access control metadata. Information package metadata can also include information search terms, package history, and notes. Packaged information can be text content, binary content, and the contents of files and other containers. A single information package can contain multiple types of information. All content not in a text form compatible with XML must be in a text encoding such as base64. Package information is protected by a digital XML signature that can be used to determine whether the information has changed since it was signed and to identify the source of the information. This specification has been tested but has not been used to create production information packages. The authors expect that gaps and unclear requirements in this specification will be identified as this specification is used to create information packages and as information stored in information packages is used. The authors expect to issue revised versions of this specification as needed to address these issues.

  20. Safety-analysis report for packaging: the ORNL DOT specification 20WC-5 - special form packaging

    SciTech Connect

    Schaich, R.W.

    1983-03-01

    The ORNL DOT Specification 20WC-5 - Special Form Packaging was fabricated at the Oak Ridge National Laboratory (ORNL) for the transport of large quantities of solid non-fissile radioactive materials in special form. the package was evaluated on the basis of tests performed at Sandia National Laboratories, Albuquerque, New Mexico (formerly Sandia Corporation), on an identical fire and impact shield and special form tests performed on a variety of stainless steel capsules at ORNL by Operations Division personnel. The results of these evaluations demonstrate that the package is in compliance with the applicable regulations for the transport of large quantities of non-fissile radioactive materials in special form. 7 figures.

  1. 49 CFR 178.350 - Specification 7A; general packaging, Type A.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Specification 7A; general packaging, Type A. 178... FOR PACKAGINGS Specifications for Packagings for Class 7 (Radioactive) Materials § 178.350 Specification 7A; general packaging, Type A. (a) Each packaging must meet all applicable requirements of...

  2. 49 CFR 178.350 - Specification 7A; general packaging, Type A.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Specification 7A; general packaging, Type A. 178... FOR PACKAGINGS Specifications for Packagings for Class 7 (Radioactive) Materials § 178.350 Specification 7A; general packaging, Type A. (a) Each packaging must meet all applicable requirements of...

  3. 49 CFR 178.350 - Specification 7A; general packaging, Type A.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Specification 7A; general packaging, Type A. 178... FOR PACKAGINGS Specifications for Packagings for Class 7 (Radioactive) Materials § 178.350 Specification 7A; general packaging, Type A. (a) Each packaging must meet all applicable requirements of...

  4. 77 FR 67678 - Content Specifications and Shielding Evaluations for Type B Transportation Packages

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-11-13

    ... COMMISSION Content Specifications and Shielding Evaluations for Type B Transportation Packages AGENCY... Regulatory Issue Summary (RIS) 2012-XX, ``Content Specifications and Shielding Evaluations for Type B... Plan for Transport Packages for Radioactive Material,'' for the review of content specifications...

  5. 49 CFR 178.350 - Specification 7A; general packaging, Type A.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Specification 7A; general packaging, Type A. 178... Specification 7A; general packaging, Type A. (a) Each packaging must meet all applicable requirements of subpart... of §§ 173.403, 173.410, 173.412, 173.415 and 173.465 of this subchapter for Type A packaging....

  6. System specification for the plutonium stabilization and packaging system

    SciTech Connect

    1996-07-01

    This document describes functional design requirements for the Plutonium Stabilization and Packaging System (Pu SPS), as required by DOE contract DE-AC03-96SF20948 through contract modification 9 for equipment in Building 707 at Rocky Flats Environmental Technology Site (RFETS).

  7. 49 CFR 173.62 - Specific packaging requirements for explosives.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... paper, multiwall, water resistantplastics woven plastics Receptacles fibreboard metal plastics wood... wood, sift-proof Sheets paper, water resistant paper, waxed plastics woven plastics (5H1/2/3).paper.... PARTICULAR PACKING REQUIREMENTS OR EXCEPTIONS:1. The Intermediate packagings must be filled with...

  8. Towards Data Repository Interoperability: The Data Conservancy Data Packaging Specification

    NASA Astrophysics Data System (ADS)

    DiLauro, T.; Duerr, R.; Thessen, A. E.; Rippin, M.; Pralle, B.; Choudhury, G. S.

    2013-12-01

    A modern data archive must support a variety of functions and services for a broad set of stakeholders over a variety of content. Data producers need to deposit this content; data consumers need to find and access it; journal publishers need to link to and from it; funders need to ensure that it is protected and its value enhanced; research institutions need to track it; and the archive itself needs to manage and preserve it. But there is not an optimal information model that supports all of these tasks. The attributes needed to manage format transformations for long-term preservation are different from, for example, those needed to understand provenance relationships among the various entities modeled in the archive. Exposing all possible properties to every function burdens users and makes it difficult to maintain a separation of concerns among the functional components. The Data Conservancy Software (DCS) manages these overlapping information needs by defining strict interfaces between components and providing mappers between the layers of the architecture. Still, work remains to make deposit more intuitive. Currently, depositing content into a DCS instance requires either very simple objects (e.g., one file equals one data item), significant manual effort, or detailed knowledge of DCS-internal data model serializations. And if one were to deposit that content into another type of archive, it would be necessary to repeat this effort. To allow data producers and consumers to interact with data in a more natural manner, the Data Conservancy[1] is developing a packaging approach that eases this burden and allows a semantic overlay atop the directory/folder and file metaphor that is more familiar. The standards-based packaging scheme augments the payload and validation capabilities of Bagit[2] with the relationship and resource description capabilities of the Open Archives Initiative (OAI) Object Reuse and Exchange (ORE)[3] model. In the absence of the ORE resource

  9. The OFP-6M transport jet

    NASA Technical Reports Server (NTRS)

    Alexander, Kelly; Heneghan, Brian; Holmes, Joules; Hughes, Bret; Kettering, Mark; Wells, Jennifer; Whelan, Todd

    1994-01-01

    This report presents a preliminary design of a commercial jet transport that meets the criteria of the Request For Proposal presented by the American Institute of Aeronautics and Astronauts (AIAA). The proposal requires an innovative design of a low cost domestic commercial transport that will reduce operating costs for airline companies while still meeting present and future requirements of the Federal Aviation Regulations for this type of aircraft. Specifications for the design include a mixed class, 153 passenger aircraft, traveling a range of 3000 nm. The intent of the project is to identify factors that reduce cost and to design within the limits of these constraints. The project includes techniques or options that incorporate new technologies but do not override practicality, alternative design approaches, and a comparison between the new design and current aircraft in its class. The OFP-6M is an alternative design approach to the conventional commercial transport jet and is geared towards customer satisfaction through efficiency and reliability. The goals of the OFP-6M transport design are to provide original, sensible, and practical solutions by combining essential preliminary design factors with growing technology. The design focus of the OFP-6M reduces costs by simplifying systems where significant weight or maintenance savings can be achieved, and by integrating advanced technology for improved performance. Key aspects of the OFP-6M design are efficient use of materials like composites, and efficient advanced ducted high bypass turbofan engines. The high bypass engines lower fuel consumption and aid in reducing costs and meeting future noise emission restrictions. Composites are used for most structural components, including flooring and wing box. Although composites are an emerging technology and presently, a high maintenance material, they can be cost effective and an alternative to aluminum structures when correct manufacturing and design strategies

  10. 78 FR 26090 - Content Specifications and Shielding Evaluations for Type B Transportation Packages

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-03

    ... this RIS as a draft for public comment on November 13, 2012 (77 FR 67678), for a 45-day comment period... COMMISSION Content Specifications and Shielding Evaluations for Type B Transportation Packages AGENCY... Regulatory Commission (NRC) is issuing Regulatory Issue Summary (RIS) 2013-04, ``Content Specifications...

  11. Test and evaluation document for DOT Specification 7A type A packaging. Volume 1

    SciTech Connect

    Kelly, D L

    1997-08-04

    The US Department of Energy (DOE) has been conducting, through several of its operating contractors, an evaluation and testing program to qualify Type A radioactive material packagings per US Department of Transportation (DOT) Specification 7A (DOT-7A) of the Code of Federal Regulations (CFR), Title 49, Part 178 (49 CFR 178). This document summarizes the evaluation and testing performed for all of the packagings successfully qualified in this program. This document supersedes DOE Evaluation Document for DOT-7A Type A Packaging (Edling 1987), originally issued in 1987 by Monsanto Research Corporation Mound Laboratory (MLM), Miamisburg, Ohio, for the Department of Energy, Security Evaluation Program (I)P-4. Mound Laboratory issued four revisions to the document between November 1988 and December 1989. In September 1989, the program was transferred to Westinghouse Hanford Company (Westinghouse Hanford) in Richland, Washington. One additional revision was issued in March 1990 by Westinghouse Hanford. This revision reflects the earlier material and incorporates a number of changes. Evaluation and testing activities on 1208 three DOT-7A Program Dockets resulted in the qualification of three new packaging configurations, which are incorporated herein and summarized. This document presents approximately 300 different packagings that have been determined to meet the requirements for a DOT-7A, type A packaging per 49 CFR 178.350.

  12. Genetics of Critical Contacts and Clashes in the DNA Packaging Specificities of Bacteriophages λ and 21

    PubMed Central

    Sippy, Jean; Patel, Priyal; Vahanian, Nicole; Sippy, Rachel; Feiss, Michael

    2016-01-01

    The cos sites in λ and 21 chromosomes contain binding sites that recruit terminase to initiate DNA packaging. The small subunits of terminase, gpNu1 (λ) and gp1 (21), have winged helix-turn-helix DNA binding domains, where the recognition helixes differ in four of nine residues. To initiate packaging, the small subunit binds three R sequences in the cosB subsite. λ and 21 cannot package each other's DNA, due to recognition helix and R sequence differences. In λ and 21 cosBs, two bp, tri1 and tri2, are conserved in the R sequences yet differ between the phages; they are proposed to play a role in phage-specific packaging by λ and 21. Genetic experiments done with mixed and matched terminase and cosB alleles show packaging specificity depends on favorable contacts and clashes. These interactions indicate that the recognition helixes orient with residues 20 and 24 proximal to tri2 and tri1, respectively. PMID:25543962

  13. An RNA Domain Imparts Specificity and Selectivity to a Viral DNA Packaging Motor

    PubMed Central

    Zhao, Wei; Jardine, Paul J.

    2015-01-01

    ABSTRACT During assembly, double-stranded DNA viruses, including bacteriophages and herpesviruses, utilize a powerful molecular motor to package their genomic DNA into a preformed viral capsid. An integral component of the packaging motor in the Bacillus subtilis bacteriophage ϕ29 is a viral genome-encoded pentameric ring of RNA (prohead RNA [pRNA]). pRNA is a 174-base transcript comprised of two domains, domains I and II. Early studies initially isolated a 120-base form (domain I only) that retains high biological activity in vitro; hence, no function could be assigned to domain II. Here we define a role for this domain in the packaging process. DNA packaging using restriction digests of ϕ29 DNA showed that motors with the 174-base pRNA supported the correct polarity of DNA packaging, selectively packaging the DNA left end. In contrast, motors containing the 120-base pRNA had compromised specificity, packaging both left- and right-end fragments. The presence of domain II also provides selectivity in competition assays with genomes from related phages. Furthermore, motors with the 174-base pRNA were restrictive, in that they packaged only one DNA fragment into the head, whereas motors with the 120-base pRNA packaged several fragments into the head, indicating multiple initiation events. These results show that domain II imparts specificity and stringency to the motor during the packaging initiation events that precede DNA translocation. Heteromeric rings of pRNA demonstrated that one or two copies of domain II were sufficient to impart this selectivity/stringency. Although ϕ29 differs from other double-stranded DNA phages in having an RNA motor component, the function provided by pRNA is carried on the motor protein components in other phages. IMPORTANCE During virus assembly, genome packaging involves the delivery of newly synthesized viral nucleic acid into a protein shell. In the double-stranded DNA phages and herpesviruses, this is accomplished by a powerful

  14. Simple and Conditional Discrimination and Specific Reinforcement in Teaching Reading: An Intervention Package

    ERIC Educational Resources Information Center

    Zaine, Isabela; Domeniconi, Camila; de Rose, Julio C.

    2014-01-01

    This study evaluated an intervention package combining simple and conditional discrimination training and specific reinforcement for each stimulus class in teaching reading of simple words to individuals with intellectual disabilities. In conditional discrimination training, participants matched printed words and pictures to the recorded sounds…

  15. Test and evaluation document for DOT Specification 7A Type A Packaging. Revision 3

    SciTech Connect

    1996-01-30

    The US Department of Energy (DOE) has been conducting, through several of its operating contractors, an evaluation and testing program to qualify Type A radioactive material packagings per US Department of Transportation (DOT) Specification 7A (DOT-7A) of the Code of Federal Regulations (CFR), Title 49, Part 178 (49 CFR 178). The program is currently administered by the DOE, Office of Facility Safety Analysis, DOE/EH-32, at DOE-Headquarters (DOE-HQ) in Germantown, Maryland. This document summarizes the evaluation and testing performed for all of the packagings successfully qualified in this program.

  16. DEVELOPMENT OF BURN TEST SPECIFICATIONS FOR FIRE PROTECTION MATERIALS IN RAM PACKAGES

    SciTech Connect

    Gupta, N.

    2010-03-03

    The regulations in 10 CFR 71 require that the radioactive material (RAM) packages must be able to withstand specific fire conditions given in 10 CFR 71.73 during Hypothetical Accident Conditions (HAC). This requirement is normally satisfied by extensive testing of full scale test specimens under required test conditions. Since fire test planning and execution is expensive and only provides a single snapshot into a package performance, every effort is made to minimize testing and supplement tests with results from computational thermal models. However, the accuracy of such thermal models depends heavily on the thermal properties of the fire insulating materials that are rarely available at the regulatory fire temperatures. To the best of authors knowledge no test standards exist that could be used to test the insulating materials and derive their thermal properties for the RAM package design. This paper presents a review of the existing industry fire testing standards and proposes testing methods that could serve as a standardized specification for testing fire insulating materials for use in RAM packages.

  17. Specificity of Rous sarcoma virus nucleocapsid protein in genomic RNA packaging.

    PubMed Central

    Dupraz, P; Spahr, P F

    1992-01-01

    Site-directed mutagenesis has shown that the nucleocapsid (NC) protein of Rous sarcoma virus (RSV) is required for packaging and dimerization of viral RNA. However, it has not been possible to demonstrate, in vivo or in vitro, specific binding of viral RNA sequences by NC. To determine whether specific packaging of viral RNA is mediated by NC in vivo, we have constructed RSV mutants carrying sequences of Moloney murine leukemia virus (MoMuLV). Either the NC coding region alone, the psi RNA packaging sequence, or both the NC and psi sequences of MoMuLV were substituted for the corresponding regions of a full-length RSV clone to yield chimeric plasmid pAPrcMNC, pAPrc psi M, or pAPrcM psi M, respectively. In addition, a mutant of RSV in which the NC is completely deleted was tested as a control. Upon transfection, each of the chimeric mutants produced viral particles containing processed core proteins but were noninfectious. Thus, MoMuLV NC can replace RSV NC functionally in the assembly and release of mature virions but not in infectivity. Surprisingly, the full-deletion mutant showed a strong block in virus release, suggesting that NC is involved in virus assembly. Mutant PrcMNC packaged 50- to 100-fold less RSV RNA than did the wild type; in cotransfection experiments, MoMuLV RNA was preferentially packaged. This result suggests that the specific recognition of viral RNA during virus assembly involves, at least in part, the NC protein. Images PMID:1378506

  18. Design of compact freeform lens for application specific Light-Emitting Diode packaging.

    PubMed

    Wang, Kai; Chen, Fei; Liu, Zongyuan; Luo, Xiaobing; Liu, Sheng

    2010-01-18

    Application specific LED packaging (ASLP) is an emerging technology for high performance LED lighting. We introduced a practical design method of compact freeform lens for extended sources used in ASLP. A new ASLP for road lighting was successfully obtained by integrating a polycarbonate compact freeform lens of small form factor with traditional LED packaging. Optical performance of the ASLP was investigated by both numerical simulation based on Monte Carlo ray tracing method and experiments. Results demonstrated that, comparing with traditional LED module integrated with secondary optics, the ASLP had advantages of much smaller size in volume (approximately 1/8), higher system lumen efficiency (approximately 8.1%), lower cost and more convenience for customers to design and assembly, enabling possible much wider applications of LED for general road lighting. Tolerance analyses were also conducted. Installation errors of horizontal and vertical deviations had more effects on the shape and uniformity of radiation pattern compared with rotational deviation. The tolerances of horizontal, vertical and rotational deviations of this lens were 0.11 mm, 0.14 mm and 2.4 degrees respectively, which were acceptable in engineering. PMID:20173861

  19. System specification/system design document comment review: Plutonium Stabilization and Packaging System. Notes of conference

    SciTech Connect

    1996-07-01

    A meeting was held between DOE personnel and the BNFL team to review the proposed resolutions to DOE comments on the initial issue of the system specification and system design document for the Plutonium Stabilization and Packaging System. The objectives of this project are to design, fabricate, install, and start up a glovebox system for the safe repackaging of plutonium oxide and metal, with a requirement of a 50-year storage period. The areas discussed at the meeting were: nitrogen in can; moisture instrumentation; glovebox atmosphere; can marking-bar coding; weld quality; NFPA-101 references; inner can swabbing; ultimate storage environment; throughput; convenience can screw-top design; furnace/trays; authorization basis; compactor safety; schedule for DOE review actions; fire protection; criticality safety; applicable standards; approach to MC and A; homogeneous oxide; resistance welder power; and tray overfill. Revised resolutions were drafted and are presented.

  20. DNA Packaging Specificity of Bacteriophage N15 with an Excursion into the Genetics of a Cohesive End Mismatch

    PubMed Central

    Feiss, Michael; Young Min, Jea; Sultana, Sawsan; Patel, Priyal; Sippy, Jean

    2015-01-01

    During DNA replication by the λ-like bacteriophages, immature concatemeric DNA is produced by rolling circle replication. The concatemers are processed into mature chromosomes with cohesive ends, and packaged into prohead shells, during virion assembly. Cohesive ends are generated by the viral enzyme terminase, which introduces staggered nicks at cos, an approx. 200 bp-long sequence containing subsites cosQ, cosN and cosB. Interactions of cos subsites of immature concatemeric DNA with terminase orchestrate DNA processing and packaging. To initiate DNA packaging, terminase interacts with cosB and nicks cosN. The cohesive ends of N15 DNA differ from those of λ at 2/12 positions. Genetic experiments show that phages with chromosomes containing mismatched cohesive ends are functional. In at least some infections, the cohesive end mismatch persists through cyclization and replication, so that progeny phages of both allelic types are produced in the infected cell. N15 possesses an asymmetric packaging specificity: N15 DNA is not packaged by phages λ or 21, but surprisingly, N15-specific terminase packages λ DNA. Implications for genetic interactions among λ-like bacteriophages are discussed. PMID:26633301

  1. Specificity of neomycin analogues bound to the packaging region of human immunodeficiency virus type 1 RNA.

    PubMed

    McPike, Mark P; Goodisman, Jerry; Dabrowiak, James C

    2004-04-15

    -neo must be directed away from the binding pocket when these analogues are bivalently bound to RNA. This study showed how variations in the structure of aminoglycosides lead to different binding specificity to part of the packaging region of HIV-1. Such knowledge will be important in design of drugs to target this region. PMID:15051052

  2. Disruption of Specific RNA-RNA Interactions in a Double-Stranded RNA Virus Inhibits Genome Packaging and Virus Infectivity.

    PubMed

    Fajardo, Teodoro; Sung, Po-Yu; Roy, Polly

    2015-12-01

    Bluetongue virus (BTV) causes hemorrhagic disease in economically important livestock. The BTV genome is organized into ten discrete double-stranded RNA molecules (S1-S10) which have been suggested to follow a sequential packaging pathway from smallest to largest segment during virus capsid assembly. To substantiate and extend these studies, we have investigated the RNA sorting and packaging mechanisms with a new experimental approach using inhibitory oligonucleotides. Putative packaging signals present in the 3'untranslated regions of BTV segments were targeted by a number of nuclease resistant oligoribonucleotides (ORNs) and their effects on virus replication in cell culture were assessed. ORNs complementary to the 3' UTR of BTV RNAs significantly inhibited virus replication without affecting protein synthesis. Same ORNs were found to inhibit complex formation when added to a novel RNA-RNA interaction assay which measured the formation of supramolecular complexes between and among different RNA segments. ORNs targeting the 3'UTR of BTV segment 10, the smallest RNA segment, were shown to be the most potent and deletions or substitution mutations of the targeted sequences diminished the RNA complexes and abolished the recovery of viable viruses using reverse genetics. Cell-free capsid assembly/RNA packaging assay also confirmed that the inhibitory ORNs could interfere with RNA packaging and further substitution mutations within the putative RNA packaging sequence have identified the recognition sequence concerned. Exchange of 3'UTR between segments have further demonstrated that RNA recognition was segment specific, most likely acting as part of the secondary structure of the entire genomic segment. Our data confirm that genome packaging in this segmented dsRNA virus occurs via the formation of supramolecular complexes formed by the interaction of specific sequences located in the 3' UTRs. Additionally, the inhibition of packaging in-trans with inhibitory ORNs

  3. Disruption of Specific RNA-RNA Interactions in a Double-Stranded RNA Virus Inhibits Genome Packaging and Virus Infectivity

    PubMed Central

    Fajardo, Teodoro; Sung, Po-Yu; Roy, Polly

    2015-01-01

    Bluetongue virus (BTV) causes hemorrhagic disease in economically important livestock. The BTV genome is organized into ten discrete double-stranded RNA molecules (S1-S10) which have been suggested to follow a sequential packaging pathway from smallest to largest segment during virus capsid assembly. To substantiate and extend these studies, we have investigated the RNA sorting and packaging mechanisms with a new experimental approach using inhibitory oligonucleotides. Putative packaging signals present in the 3’untranslated regions of BTV segments were targeted by a number of nuclease resistant oligoribonucleotides (ORNs) and their effects on virus replication in cell culture were assessed. ORNs complementary to the 3’ UTR of BTV RNAs significantly inhibited virus replication without affecting protein synthesis. Same ORNs were found to inhibit complex formation when added to a novel RNA-RNA interaction assay which measured the formation of supramolecular complexes between and among different RNA segments. ORNs targeting the 3’UTR of BTV segment 10, the smallest RNA segment, were shown to be the most potent and deletions or substitution mutations of the targeted sequences diminished the RNA complexes and abolished the recovery of viable viruses using reverse genetics. Cell-free capsid assembly/RNA packaging assay also confirmed that the inhibitory ORNs could interfere with RNA packaging and further substitution mutations within the putative RNA packaging sequence have identified the recognition sequence concerned. Exchange of 3’UTR between segments have further demonstrated that RNA recognition was segment specific, most likely acting as part of the secondary structure of the entire genomic segment. Our data confirm that genome packaging in this segmented dsRNA virus occurs via the formation of supramolecular complexes formed by the interaction of specific sequences located in the 3’ UTRs. Additionally, the inhibition of packaging in-trans with inhibitory

  4. Image dissector control and data system, part 1. [instrument packages and equipment specifications

    NASA Technical Reports Server (NTRS)

    1974-01-01

    A general description of the image dissector control and data system is presented along with detailed design information, operating instructions, and maintenance and trouble-shooting procedures for the four instrumentation packages. The four instrumentation packages include a 90 inch telescope, a simplified telescope module for use on the 90 inch or other telescopes, a photographic plate scanner module which permits the scanning of astronomical photographic plates in the laboratory, and the lunar experiment package module.

  5. Review: placenta-specific microRNAs in exosomes - good things come in nano-packages.

    PubMed

    Ouyang, Y; Mouillet, J-F; Coyne, C B; Sadovsky, Y

    2014-02-01

    MicroRNAs (miRNAs) are small noncoding RNA gene products that commonly regulate mRNA expression by repression of translation and/or transcript decay. Whereas common and unique types of miRNAs are expressed by the placenta during pregnancy, the functions of most placental miRNA species are unknown. In addition to their intracellular silencing function, miRNAs are also released to the extracellular space and systemic circulation, where they can potentially target cells to regulate mRNA and protein expression, providing a non-hormonal means of intercellular communication that contributes to tissue homeostasis and disease pathophysiology. This review centers on extracellular miRNAs that originate in trophoblasts and that could mediate crosstalk between the feto-placental unit and the mother during pregnancy. We specifically detail the function of miRNAs from the primate-specific chromosome 19 miRNA cluster. These miRNAs are highly expressed in human placentas and in the serum of pregnant women. They are also packaged into extracellular vesicles of diverse sizes, including exosomes, and endow non-trophoblastic cells with resistance to a variety of viruses. PMID:24280233

  6. Power Extension Package (PEP) system definition extension, orbital service module systems analysis study. Volume 4: PEP functional specification

    NASA Technical Reports Server (NTRS)

    1979-01-01

    The functional, performance, design, and test requirements for the Orbiter power extension package and its associated ground support equipment are defined. Both government and nongovernment standards and specifications are cited for the following subsystems: electrical power, structural/mechanical, avionics, and thermal control. Quality control assurance provisions and preparation for delivery are also discussed.

  7. Power Extension Package (PEP) system definition extension, orbital service module systems analysis study. Volume 5: PEP environmental specification

    NASA Technical Reports Server (NTRS)

    1979-01-01

    This specification establishes the natural and induced environments to which the power extension package may be exposed during ground operations and space operations with the shuttle system. Space induced environments are applicable at the Orbiter attach point interface location. All probable environments are systematically listed according to each ground and mission phase.

  8. Retrovirus-Specific Differences in Matrix and Nucleocapsid Protein-Nucleic Acid Interactions: Implications for Genomic RNA Packaging

    PubMed Central

    Sun, Meng; Grigsby, Iwen F.; Gorelick, Robert J.; Mansky, Louis M.

    2014-01-01

    Retroviral RNA encapsidation involves a recognition event between genomic RNA (gRNA) and one or more domains in Gag. In HIV-1, the nucleocapsid (NC) domain is involved in gRNA packaging and displays robust nucleic acid (NA) binding and chaperone functions. In comparison, NC of human T-cell leukemia virus type 1 (HTLV-1), a deltaretrovirus, displays weaker NA binding and chaperone activity. Mutation of conserved charged residues in the deltaretrovirus bovine leukemia virus (BLV) matrix (MA) and NC domains affects virus replication and gRNA packaging efficiency. Based on these observations, we hypothesized that the MA domain may generally contribute to NA binding and genome encapsidation in deltaretroviruses. Here, we examined the interaction between HTLV-2 and HIV-1 MA proteins and various NAs in vitro. HTLV-2 MA displays higher NA binding affinity and better chaperone activity than HIV-1 MA. HTLV-2 MA also binds NAs with higher affinity than HTLV-2 NC and displays more robust chaperone function. Mutation of two basic residues in HTLV-2 MA α-helix II, previously implicated in BLV gRNA packaging, reduces NA binding affinity. HTLV-2 MA binds with high affinity and specificity to RNA derived from the putative packaging signal of HTLV-2 relative to nonspecific NA. Furthermore, an HIV-1 MA triple mutant designed to mimic the basic character of HTLV-2 MA α-helix II dramatically improves binding affinity and chaperone activity of HIV-1 MA in vitro and restores RNA packaging to a ΔNC HIV-1 variant in cell-based assays. Taken together, these results are consistent with a role for deltaretrovirus MA proteins in viral RNA packaging. PMID:24227839

  9. 49 CFR 171.23 - Requirements for specific materials and packagings transported under the ICAO Technical...

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... oxygen service conform to the requirements of this paragraph, except when the cylinder is used for...-belt pretensioners meeting the criteria for a Division 1.4G material. (3) Chemical oxygen generators. Chemical oxygen generators must be approved, classed, described, packaged, and transported in...

  10. Conceptual waste package interim product specifications and data requirements for disposal of borosilicate glass defense high-level waste forms in salt geologic repositories

    SciTech Connect

    Not Available

    1983-06-01

    The conceptual waste package interim product specifications and data requirements presented are applicable specifically to the normal borosilicate glass product of the Defense Waste Processing Facility (DWPF). They provide preliminary numerical values for the defense high-level waste form parameters and properties identified in the waste form performance specification for geologic isolation in salt repositories. Subject areas treated include containment and isolation, operational period safety, criticality control, waste form/production canister identification, and waste package performance testing requirements. This document was generated for use in the development of conceptual waste package designs in salt. It will be revised as additional data, analyses, and regulatory requirements become available.

  11. Sequence Determinants for DNA Packaging Specificity in the S. aureus Pathogenicity Island SaPI1

    PubMed Central

    Bento, Joana C; Lane, Kristin D; Read, Erik K; Cerca, Nuno; Christie, Gail E

    2014-01-01

    The SaPIs and their relatives are a family of genomic islands that exploit helper phages for high frequency horizontal transfer. One of the mechanisms used by SaPIs to accomplish this molecular piracy is the redirection of the helper phage DNA packaging machinery. SaPIs encode a small terminase subunit that can be substituted for that of the phage. In this study we have determined the initial packaging cleavage sites for helper phage 80α which uses the phage-encoded small terminase subunit, and for SaPI1, which uses the SaPI-encoded small terminase subunit. We have identified a 19 nt SaPI1 sequence that is necessary and sufficient to allow high frequency 80α transduction of a plasmid by a terminase carrying the SaPI1-encoded small subunit. We also show that the hybrid enzyme with the SaPI1 small terminase subunit is capable of generalized transduction. PMID:24365721

  12. Sequence determinants for DNA packaging specificity in the S. aureus pathogenicity island SaPI1.

    PubMed

    Bento, Joana C; Lane, Kristin D; Read, Erik K; Cerca, Nuno; Christie, Gail E

    2014-01-01

    The SaPIs and their relatives are a family of genomic islands that exploit helper phages for high frequency horizontal transfer. One of the mechanisms used by SaPIs to accomplish this molecular piracy is the redirection of the helper phage DNA packaging machinery. SaPIs encode a small terminase subunit that can be substituted for that of the phage. In this study we have determined the initial packaging cleavage sites for helper phage 80α, which uses the phage-encoded small terminase subunit, and for SaPI1, which uses the SaPI-encoded small terminase subunit. We have identified a 19nt SaPI1 sequence that is necessary and sufficient to allow high frequency 80α transduction of a plasmid by a terminase carrying the SaPI1-encoded small subunit. We also show that the hybrid enzyme with the SaPI1 small terminase subunit is capable of generalized transduction. PMID:24365721

  13. Differential Control of Interleukin-6 mRNA Levels by Cellular Distribution of YB-1

    PubMed Central

    Kang, Sujin; Lee, Taeyun A.; Ra, Eun A.; Lee, Eunhye; Choi, Hyun jin; Lee, Sungwook; Park, Boyoun

    2014-01-01

    Cytokine production is essential for innate and adaptive immunity against microbial invaders and must be tightly controlled. Cytokine messenger RNA (mRNA) is in constant flux between the nucleus and the cytoplasm and in transcription, splicing, or decay; such processes must be tightly controlled. Here, we report a novel function of Y-box-binding protein 1 (YB-1) in modulating interleukin-6 (IL-6) mRNA levels in a cell type-specific manner. In lipopolysaccharide (LPS)-stimulated macrophages, YB-1 interacts with IL-6 mRNA and actively transports it to the extracellular space by YB-1-enriched vesicles, resulting in the proper maintenance of intracellular IL-6 mRNA levels. YB-1 secretion occurs in a cell type-specific manner. Whereas macrophages actively secret YB-1, dendritic cells maintain it predominantly in the cytoplasm even in response to LPS. Intracellular YB-1 has the distinct function of regulating IL-6 mRNA stability in dendritic cells. Moreover, because LPS differentially regulates the expression of histone deacetylase 6 (HDAC6) in macrophages and dendritic cells, this stimulus might control YB-1 acetylation differentially in both cell types. Taken together, these results suggest a unique feature of YB-1 in controlling intracellular IL-6 mRNA levels in a cell type-specific manner, thereby leading to functions that are dependent on the extracellular and intracellular distribution of YB-1. PMID:25398005

  14. Changes in the specific migration characteristics of packaging-food simulant combinations caused by ionizing radiation: Effect of food simulant

    NASA Astrophysics Data System (ADS)

    Zygoura, Panagiota D.; Paleologos, Evangelos K.; Kontominas, Michael G.

    2011-08-01

    The primary objective of the present study was to evaluate the extent to which the affinity of the surrounding medium for the migrant, as well as the packaging material, affects the specific migration characteristics of the latter. For this purpose, migration tests were conducted with vinylidene chloride copolymer (PVDC/PVC) in contact with the EU specified solvents simulating all food types: namely, distilled water, 3% w/v acetic acid, 10% v/v ethanol and isooctane. Migration testing was carried out at 40 °C for 10 days for the aqueous simulants, and at 20 °C for 2 days for the fatty food simulant (EC, 1997; EEC, 1993). In addition, food-grade saran film was subjected to ionizing radiation treatment with a [60Co] source at doses equal to 5, 15 and 25 kGy. Acetyl tributyl citrate (ATBC) plasticizer levels were monitored as a function of time for untreated, as well as gamma-irradiated packaging material, with a secondary objective to investigate the effect of ionizing radiation on polymer/migrant/surrounding medium interactions. Depending on the food simulant, determination of the analyte was performed by either direct gas chromatographic analysis, or surfactant (Triton X-114) mediated extraction followed by gas chromatographic-flame ionization detection (GC-FID). ATBC concentrations determined in aqueous and fatty food simulants were 0.216-0.497 and 5.0-5.9 mg/L, respectively. Therefore, the most efficient extracting medium of plasticizers in vinyl chloride copolymers is the non-polar isooctane. Moreover, an extremely high rate of ATBC migration into isooctane during the early stages of contact was observed. The above observation verifies the aggressiveness of isooctane towards plastic packaging materials. Amongst the aqueous food simulants tested, the 10% ethanol solution demonstrated the highest migration levels. Gamma-irradiation enhanced ATBC migration; specific migration levels increased with increasing contact time and radiation dose. This was expected

  15. General specifications for the development of a USL NASA PC R and D statistical analysis support package

    NASA Technical Reports Server (NTRS)

    Dominick, Wayne D. (Editor); Bassari, Jinous; Triantafyllopoulos, Spiros

    1984-01-01

    The University of Southwestern Louisiana (USL) NASA PC R and D statistical analysis support package is designed to be a three-level package to allow statistical analysis for a variety of applications within the USL Data Base Management System (DBMS) contract work. The design addresses usage of the statistical facilities as a library package, as an interactive statistical analysis system, and as a batch processing package.

  16. Development of a functional cell-based assay that probes the specific interaction between influenza A virus NP and its packaging signal sequence RNA.

    PubMed

    Woo, Jiwon; Yu, Kyung Lee; Lee, Sun Hee; You, Ji Chang

    2015-02-01

    Although cis-acting packaging signal RNA sequences for the influenza virus NP encoding vRNA have been identified recently though genetic studies, little is known about the interaction between NP and the vRNA packaging signals either in vivo or in vitro. Here, we provide evidence that NP is able to interact specifically with the vRNA packaging sequence RNA within living cells and that the specific RNA binding activity of NP in vivo requires both the N-terminal and central region of the protein. This assay established would be a valuable tool for further detailed studies of the NP-packaging signal RNA interaction in living cells. PMID:25559349

  17. 49 CFR 173.8 - Exceptions for non-specification packagings used in intrastate transportation.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... and parts 178 and 180 of this subchapter, a non-specification metal tank permanently secured to a... used to transport a flammable cryogenic liquid, hazardous substance, hazardous waste, or a marine...) or (c) of this section, conform to all requirements in part 180 (except for § 180.405(g)) of...

  18. THERMAL UPGRADING OF 9977 RADIOACTIVE MATERIAL (RAM) TYPE B PACKAGE

    SciTech Connect

    Gupta, N.; Abramczyk, G.

    2012-03-26

    The 9977 package is a radioactive material package that was originally certified to ship Heat Sources and RTG contents up to 19 watts and it is now being reviewed to significantly expand its contents in support of additional DOE missions. Thermal upgrading will be accomplished by employing stacked 3013 containers, a 3013 aluminum spacer and an external aluminum sleeve for enhanced heat transfer. The 7th Addendum to the original 9977 package Safety Basis Report describing these modifications is under review for the DOE certification. The analyses described in this paper show that this well-designed and conservatively analyzed package can be upgraded to carry contents with decay heat up to 38 watts with some simple design modifications. The Model 9977 package has been designed as a replacement for the Department of Transportation (DOT) Fissile Specification 6M package. The 9977 package is a very versatile Type B package which is certified to transport and store a wide spectrum of radioactive materials. The package was analyzed quite conservatively to increase its usefulness and store different payload configurations. Its versatility is evident from several daughter packages such as the 9978 and H1700, and several addendums where the payloads have been modified to suit the Shipper's needs without additional testing.

  19. EARLY TESTS OF DRUM TYPE PACKAGINGS - THE LEWALLEN REPORT

    SciTech Connect

    Smith, A.

    2010-07-29

    The need for robust packagings for radioactive materials (RAM) was recognized from the earliest days of the nuclear industry. The U.S. Department of Energy (DOE) Rocky Flats Plant developed a packaging for shipment of Pu in the early 1960's, which became the U.S. Department of Transportation (DOT) 6M specification package. The design concepts were employed in other early packagings. Extensive tests of these at Savannah River Laboratory (now Savannah River National Laboratory) were performed in 1969 and 1970. The results of these tests were reported in 'Drum and Board-Type Insulation Overpacks of Shipping Packages for Radioactive Materials', by E. E. Lewallen. The Lewallen Report was foundational to design of subsequent drum type RAM packaging. This paper summarizes this important early study of drum type packagings. The Lewallen Report demonstrated the ability packagings employing drum and insulation board overpacks and engineered containment vessels to meet the Type B package requirements. Because of the results of the Lewallen Report, package designers showed high concern for thermal protection of 'Celotex'. Subsequent packages addressed this by following strategies like those recommended by Lewallen and by internal metal shields and supplemental, encapsulated insulation disks, as in 9975. The guidance provide by the Lewallen Report was employed in design of a large number of drum size packagings over the following three decades. With the increased public concern over transportation of radioactive materials and recognition of the need for larger margins of safety, more sophisticated and complex packages have been developed and have replaced the simple packagings developed under the Lewallen Report paradigm.

  20. Definition of Small Gram Quantity Contents for Type B Radioactive Material Transportation Packages: Activity-Based Content Limitations

    SciTech Connect

    Sitaraman, S; Kim, S; Biswas, D; Hafner, R; Anderson, B

    2010-10-27

    Since the 1960's, the Department of Transportation Specification (DOT Spec) 6M packages have been used extensively for transportation of Type B quantities of radioactive materials between Department of Energy (DOE) facilities, laboratories, and productions sites. However, due to the advancement of packaging technology, the aging of the 6M packages, and variability in the quality of the packages, the DOT implemented a phased elimination of the 6M specification packages (and other DOT Spec packages) in favor of packages certified to meet federal performance requirements. DOT issued the final rule in the Federal Register on October 1, 2004 requiring that use of the DOT Specification 6M be discontinued as of October 1, 2008. A main driver for the change was the fact that the 6M specification packagings were not supported by a Safety Analysis Report for Packaging (SARP) that was compliant with Title 10 of the Code of Federal Regulations part 71 (10 CFR 71). Therefore, materials that would have historically been shipped in 6M packages are being identified as contents in Type B (and sometimes Type A fissile) package applications and addenda that are to be certified under the requirements of 10 CFR 71. The requirements in 10 CFR 71 include that the Safety Analysis Report for Packaging (SARP) must identify the maximum radioactivity of radioactive constituents and maximum quantities of fissile constituents (10 CFR 71.33(b)(1) and 10 CFR 71.33(b)(2)), and that the application (i.e., SARP submittal or SARP addendum) demonstrates that the external dose rate (due to the maximum radioactivity of radioactive constituents and maximum quantities of fissile constituents) on the surface of the packaging (i.e., package and contents) not exceed 200 mrem/hr (10 CFR 71.35(a), 10 CFR 71.47(a)). It has been proposed that a 'Small Gram Quantity' of radioactive material be defined, such that, when loaded in a transportation package, the dose rates at external points of an unshielded packaging

  1. Refurbishment and modification of existing protective shipping packages (for 30-inch UF{sub 6} cylinders) per USDOT specification No. USA-DOT-21PF-1A

    SciTech Connect

    Housholder, W.R.

    1991-12-31

    This paper addresses the refurbishment procedures for existing shipping containers for 30-inch diameter UF{sub 6} cylinders in accordance with DOT Specification 21PF-1 and the criteria used to determine rejection when such packages are unsuitable for refurbishment.

  2. 0.6-M Antennae for the Amiba Interferometry Array

    NASA Astrophysics Data System (ADS)

    Koch, P.; Raffin, P. A.; Proty Wu, J.-H.; et al.

    2006-10-01

    The Array for Microwave Background Anisotropy (AMiBA) is a hexapod telescope for astronomy. The fully steerable platform can accommodate up to 19 dishes. We present the design, simulation, manufacturing and performance verification for the 0.6m Cassegrain antennae. The primary and secondary mirrors are carbon fiber sandwich structures, manufactured by CoTec Inc., in Taichung, Taiwan. They are aluminium coated with a final surface rms of 20-30 and 10 μm, respectively. Simulated load conditions for the mirrors show maximum rms surface errors of less than 10 μm. The measured antenna beam pattern confirms the expected performance.

  3. THERMAL TESTING OF PROTOTYPE GENERAL PURPOSE FISSILE PACKAGES USING A FURNACE

    SciTech Connect

    Smith, A; Lawrence Gelder, L; Paul Blanton, P

    2007-02-16

    The 9977/9978 General Purpose Fissile Package (GPFP) was designed by SRNL to replace the DOT 6M Specification Package and ship Plutonium and Uranium metals and oxides. Urethane foam was used for the overpack to ensure the package would withstand the 10CFR71.73(c)(2) crush test, which is a severe test for drum-type packages. In addition, it was necessary to confirm that the urethane foam configuration provided adequate thermal protection for the containment vessel during the subsequent 10CFR71.73(c)(4) thermal test. Development tests were performed on early prototype test specimens of different diameter overpacks and a range of urethane foam densities. The thermal test was performed using an industrial furnace. Test results were used to optimize the selection of package diameter and foam density, and provided the basis for design enhancements incorporated into the final package design.

  4. KATE-140 and MKF-6M space cameras

    NASA Astrophysics Data System (ADS)

    Kuchumov, V.

    1982-07-01

    The KATE-140 large-format topographic camera made it possible to obtain photographs suitable for precision photographic-survey processing. It has a field of vision of 85 deg which makes it possible for a single frame to contain an image of a 450x450-km segment of the Earth's surface from orbital altitude. Precise measurement of the linear dimensions of objects and their mutual positions can be carried out on the photographs. Moreover, the camera's high resolution meets imagery-interpretation requirements. A guidance device provides for both single and strip photographs with a given interval. A punching machine is used to separate the strips. Before being used on the Salyut-6 station, the other fixed camera, the MKF-6M, underwent thorough testing onboard the Soyuz-22 spacecraft. The multispectral MKF-6M camera is designed to obtain information about the spectral characteristics of natural objects in order to increase the reliability of their interpretation. It has six spectral channels, four of which encompass the visible spectra and two of which are in the near-infrared.

  5. EVALUATION OF RADIOLYSIS INDUCED HYDROGEN GENERATION IN DOT 6M DRUMS FROM INTEC

    SciTech Connect

    Vinson, D

    2007-06-18

    Three DOT 6M 30-gallon drums are scheduled to be shipped from the Idaho Nuclear Technology Engineering Center (INTEC) at the Idaho National Laboratory (INL) to L-Area at the Savannah River Site (SRS). These three drums contain radioactive materials that resulted from the material recovery effort following a small explosion that had occurred in the Idaho Chemical Processing Plant (ICPP) hot chemistry laboratory (HCL). In support of the shipment and subsequent storage of the three DOT 6M drums, an evaluation of the potential for molecular hydrogen production in the drums has been completed and documented herein. The potential sources of hydrogen evaluated in the current report include radiolytic decomposition of polymeric materials in the DOT 6M drums No.3031 and No.3598 and the radiolytic decomposition of water in drum No.20102. No other potential sources have been identified based upon reported drum contents and packaging configuration. A parametric approach was used to evaluate the maximum quantity of molecular hydrogen that can be expected to evolve in two DOT 6M 30-gallon drums in support of receipt and subsequent interim storage prior to canyon processing. These drums are two of three drums scheduled for shipment from INTEC to SRS as part of the decommissioning effort of the INTEC facility. The three DOT 6M drums will be received at L-Area in SRS and stored for up to 13-years prior to final disposition at HB-Line in 2020. Results of the current analysis do not include parametric analysis of drum No.20102 containing 114/133 SAL (salvage) which contains UO{sub 3} powder. This drum has not been identified as containing polymeric materials and a conservative calculation indicates that the maximum gross molecular hydrogen production due to the radiolysis of adsorbed moisture would yield a production rate of 5.1-cm{sup 3}/yr, driven primarily by the large surface are to volume ratio of the oxide powder. The remaining two drums, No.3031 and No.3598 contain polymer

  6. Control and operation of the 1.6 m New Solar Telescope in Big Bear

    NASA Astrophysics Data System (ADS)

    Varsik, J.; Plymate, C.; Goode, P.; Kosovichev, A.; Cao, W.; Coulter, R.; Ahn, K.; Gorceix, N.; Shumko, S.

    2014-08-01

    The 1.6m New Solar Telescope (NST) has developed a modern and comprehensive suite of instruments which allow high resolution observations of the Sun. The current instrument package comprises diffraction limited imaging, spectroscopic and polarimetric instruments covering the wavelength range from 0.4 to 5.0 microns. The instruments include broadband imaging, visible and near-infrared scanning Fabry-Perot interferometers, an imaging spectropolarimeter, a fast visible-light imaging spectrograph, and a unique new scanning cryogenic infrared spectrometer/spectropolarimeter that is nearing completion. Most instruments are operated with a 308 subaperture adaptive optics system, while the thermal-IR spectrometer has a correlation tracker. This paper reports on the current observational programs and operational performance of the telescope and instrumentation. The current control, data processing, and archiving systems are also briefly discussed.

  7. Packaging of electronic modules

    NASA Technical Reports Server (NTRS)

    Katzin, L.

    1966-01-01

    Study of design approaches that are taken toward optimizing the packaging of electronic modules with respect to size, shape, component orientation, interconnections, and structural support. The study does not present a solution to specific packaging problems, but rather the factors to be considered to achieve optimum packaging designs.

  8. Polarimetry of major Uranian moons at the 6-m telescope

    NASA Astrophysics Data System (ADS)

    Afanasiev, V. L.; Rosenbush, V. K.; Kiselev, N. N.

    2014-04-01

    We present the results of polarimetric observations of the icymoons of Uranus (Ariel, Titania, Oberon, and Umbriel) performed at the 6-m BTA telescope of the SAO RAS with the SCORPIO-2 focal reducer within the phase angle range of . The parameters of the negative polarization branch (referred to the scattering plane) are obtained in the V filter: for Ariel the maximum branch depth of P min ≈ -1.4% is reached at the phase angle of α min ≈ 1°; for Titania P min ≈ -1.2%, ; for Oberon P min ≈ -1.1%, . For Umbriel the polarization minimum was not reached: for the last measurement point at , polarization amounts to -1.7%. The declining P min and shifting αmin towards larger phase angles correlate with a decrease of the geometric albedo of the Uranian moons. There is no longitudinal dependence of polarization for the moons within the observational errors which indicates a similarity in the physical properties of the leading and trailing hemispheres. The phase-angle dependences of polarization for the major moons of Uranus are quite close to those observed in the group of small trans-Neptunian objects (Ixion, Huya, Varuna, 1999 DE9, etc.), which are characterized by a large gradient of negative polarization, about -1% per degree in the phase-angle range of.

  9. The development of culture-specific health education packages to increase case-finding of leprosy in Sarawak.

    PubMed

    Chen, P C; Sim, H C

    1986-09-01

    For any health education to succeed, the people's perception of the disease, their beliefs and cultural practices are of utmost importance as these have tremendous influence on their acceptance of new ideas. It is therefore essential to develop appropriate health education packages based on the understanding of the traditional and socio-cultural belief systems of the people. Thus on the basis of anthropological studies, health education packages were developed for the leprosy control programme in Sarawak, aimed at both adults and children. Newspaper articles, cartoon tape-slides, cartoon story books as well as posters were developed for both Chinese as well as other groups such as Malays, Ibans and Kayans. These were field tested and are now used in the Rejang Valley of Sarawak. PMID:3563610

  10. Circularly permuted viral pRNA active and specific in the packaging of bacteriophage phi 29 DNA.

    PubMed

    Zhang, C; Trottier, M; Guo, P

    1995-03-10

    A viral-encoded 120-base pRNA has been shown to have an essential role in the packaging of bacteriophage phi 29 DNA. The finding that both the 5'- and 3'-termini of the pRNA are proximate and crucial for biological function (C. Zhang, C. Lee, and P. Guo, 1994, Virology, 201, 77-85) prompted investigation of the activity of circularly permuted pRNAs (cpRNA) and of the expandability and essentiality of bases extending from the termini. A 117-base pRNA with a deletion of three bases downstream of the proximal terminus was active in DNA packaging. Concatemeric DNAs containing two tandem pRNA genes separated by a short or a long loop sequence were constructed. The cpRNAs from these DNA templates were transcribed in vitro and shown to be active in phi 29 DNA packaging, with activity comparable to the parental (noncircularly permuted) pRNA, indicating that neither of the loops tested affected the activity and folding of the cpRNA. As few as four bases were sufficient to serve as a loop for the terminal 180 degree turn, and a loop as long as 27 bases did not affect the cpRNA structure and function. Eight cpRNAs were constructed to assess the effect of openings within the wild-type pRNA structure. Opening of the bulge at residue 38 did not affect cpRNA activity, but opening the bulge at residue 55 greatly reduced it. Although the sequence of the 5',3'-terminal loop was not important for the folding and activity of the cpRNA, the activities of cpRNAs with openings at individual bulges or hairpins were different, indicating that each region plays a different role in pRNA folding and function. Our results indicate that it is possible to generate active circularly permuted pRNA by assigning internal sites of the pRNA as new 3'- and 5'-termini. The creation of new variable ends makes the labeling of internal bases of the pRNA molecule possible and will facilitate the analysis of pRNA secondary and tertiary structure. PMID:7533964

  11. Design and Criticality Considerations for 9977 and 9978 Shipping Packages

    SciTech Connect

    Reed, R; Biswas, D; Abramczyk, G

    2008-11-25

    Savannah River National Laboratory (SRNL) has developed two new, Type B, state-of-the-art, general purpose, fissile material Shipping Packages, designated 9977 and 9978, as replacements for the U.S. DOT specification 6M container, phased out in September 30, 2008 due to non-compliance with current requirements 10CFR71 regulation. The packages accommodate plutonium, uranium and other special nuclear materials in bulk quantities and in many forms with capabilities exceeding those of the 6M. These packages provide a high degree of single containment and comply with 10CFR71, Department of Energy (DOE) Order 460.1B, DOE Order 460.2, and 10CFR20 (As Low As Reasonably Achievable (ALARA)). Allowed package contents were determined accounting for nuclear criticality, radiation shielding, and decay heat rate. The Criticality Safety Index (CSI) for the package is 1.0. The package utilizes passive cooling to maintain internal temperatures within limits. Radiation shielding analyses have established the contents for which the packages can be shipped under non-exclusive use in the Safe-Secure Trailer or under exclusive use. The packages are designed to ship radioactive contents in several configurations; Radioisotope Thermoelectric Generators (RTGs), nested food-pack cans, site specific containers, and DOE-STD-3013 containers. Each shipping package includes a 35-gallon stainless steel outer drum, insulation, a drum liner, and a single containment vessel (CV). The 9977 includes a 6-inch ID CV while the 9978 includes a 5-inch ID CV. One inch of Fiberfrax{reg_sign} insulation is wrapped around and attached to the sides and bottom of the liner. The volume between the Fiberfrax{reg_sign} and the drum wall is filled with polyurethane foam. Top and bottom aluminum Load Distribution Fixtures (LDFs) within the drum liner cavity, above and below the CV, center the CV in the liner, stiffen the package radially, and distribute loads away from the CV. The 6CV fits directly into the LDFs while

  12. Productivity Techniques and Quality Aspects in the Criticality Safety Evaluation of Y-12 Type-B Fissile Material Packages

    SciTech Connect

    DeClue, J. F.

    2011-06-28

    The inventory of certified Type-B fissile material packages consists of ten performance-based packages for offsite transportation purposes, serving transportation programs at the Y-12 National Security Complex. The containment vessels range from 5 to 19 in. in diameter and from 17 to 58 in. in height. The drum assembly external to the containment vessel ranges from 18 to 34 in. in diameter and from 26 to 71 in. in height. The weight of the packaging (drum assembly and containment vessel) ranges from 239 to 1550 lb. The older DT-nn series of Cellotex-based packages are being phased-out and replaced by a new generation of Kaolite-based ('Y-12 patented insulation') packages capable of withstanding the dynamic crush test 10 CFR 71.73(c)(2). Three replacement packages are in various stages of development; two are in use. The U.S. Department of Transportation (DOT) 6M specification package, which does not conform to the U.S. Nuclear Regulatory Commission requirements for Type-B packages, is no longer authorized for service on public roads. The ES-3100 shipping package is an example of a Kaolite-based Type-B fissile material package developed as a replacement package for the DOT 6M. With expanded utility, the ES-3100 is designed and licensed for transporting highly enriched uranium and plutonium materials on public roads. The ES-3100 provides added capability for air transport of up to 7-kg quantities of uranium material. This paper presents the productivity techniques and quality aspects in the criticality safety evaluation of Y-12 packages using the ES-3100 as an example.

  13. Queue observing at the Observatoire du Mont-Mégantic 1.6-m telescope

    NASA Astrophysics Data System (ADS)

    Artigau, Étienne; Lamontagne, Robert; Doyon, René; Malo, Lison

    2010-07-01

    Queue planning of observation and service observing are generally seen as specific to large, world-class, astronomical observatories that draw proposal from a large community. One of the common grievance, justified or not, against queue planning and service observing is the fear of training a generation of astronomers without hands-on observing experience. At the Observatoire du Mont-Mégantic (OMM) 1.6-m telescope, we are developing a student-run service observing program. Queue planning and service observing are used as training tools to expose students to a variety of scientific project and instruments beyond what they would normally use for their own research project. The queue mode at the OMM specifically targets relatively shallow observations that can be completed in less than a few hours and are too short to justify a multi-night classical observing run.

  14. The use of duplex-specific nuclease in ribosome profiling and a user-friendly software package for Ribo-seq data analysis

    PubMed Central

    Chung, Betty Y.; Hardcastle, Thomas J.; Jones, Joshua D.; Irigoyen, Nerea; Firth, Andrew E.; Baulcombe, David C.; Brierley, Ian

    2015-01-01

    Ribosome profiling is a technique that permits genome-wide, quantitative analysis of translation and has found broad application in recent years. Here we describe a modified profiling protocol and software package designed to benefit more broadly the translation community in terms of simplicity and utility. The protocol, applicable to diverse organisms, including organelles, is based largely on previously published profiling methodologies, but uses duplex-specific nuclease (DSN) as a convenient, species-independent way to reduce rRNA contamination. We show that DSN-based depletion compares favorably with other commonly used rRNA depletion strategies and introduces little bias. The profiling protocol typically produces high levels of triplet periodicity, facilitating the detection of coding sequences, including upstream, downstream, and overlapping open reading frames (ORFs) and an alternative ribosome conformation evident during termination of protein synthesis. In addition, we provide a software package that presents a set of methods for parsing ribosomal profiling data from multiple samples, aligning reads to coding sequences, inferring alternative ORFs, and plotting average and transcript-specific aspects of the data. Methods are also provided for extracting the data in a form suitable for differential analysis of translation and translational efficiency. PMID:26286745

  15. The use of duplex-specific nuclease in ribosome profiling and a user-friendly software package for Ribo-seq data analysis.

    PubMed

    Chung, Betty Y; Hardcastle, Thomas J; Jones, Joshua D; Irigoyen, Nerea; Firth, Andrew E; Baulcombe, David C; Brierley, Ian

    2015-10-01

    Ribosome profiling is a technique that permits genome-wide, quantitative analysis of translation and has found broad application in recent years. Here we describe a modified profiling protocol and software package designed to benefit more broadly the translation community in terms of simplicity and utility. The protocol, applicable to diverse organisms, including organelles, is based largely on previously published profiling methodologies, but uses duplex-specific nuclease (DSN) as a convenient, species-independent way to reduce rRNA contamination. We show that DSN-based depletion compares favorably with other commonly used rRNA depletion strategies and introduces little bias. The profiling protocol typically produces high levels of triplet periodicity, facilitating the detection of coding sequences, including upstream, downstream, and overlapping open reading frames (ORFs) and an alternative ribosome conformation evident during termination of protein synthesis. In addition, we provide a software package that presents a set of methods for parsing ribosomal profiling data from multiple samples, aligning reads to coding sequences, inferring alternative ORFs, and plotting average and transcript-specific aspects of the data. Methods are also provided for extracting the data in a form suitable for differential analysis of translation and translational efficiency. PMID:26286745

  16. Milestone Report for High NA Optics Development International Sematech Project L1TH 112 Milestone4a: Specification Package for the Polished Mirror Substrate M1

    SciTech Connect

    Taylor, J.S.; Hale, L.

    1999-10-08

    The key task in initiating the fabrication of mirror substrates for the new High NA Camera is in preparing the specification package that details the substrate geometry and the specifications for the optical surface. This specification package has been completed for substrate M1, and the vendor has begun optical fabrication. In addition, mounting hardware has been designed and fabricated, and substrates have been bonded to the kinematic mounts. The design of the secondary substrate, M2, is underway, but will depend upon details of the PO Box actuation system and space constraints. Sufficient details of the M2 design to enable the vendor to procure material will be determined during October, while the final details of the mounting surfaces will be completed prior to the end of Q4 1999. The geometry of the Ml substrate is compatible with our planned approach for fixturing the optic within the PO Box and within metrology tools. The completion of this specification package required detailed consideration of: the mounting approach within the PO Box, degrees of actuation required for PO Box alignment, space constraints imposed by the vendor's metrology, requirements for LLNL metrology, and datum definitions needed for mechanical assembly of the PO Box. In addition, each of the degrees of freedom of the substrate has been properly constrained, and shown to be sufficiently insensitive to disturbance forces for minimizing deformation. An approach to fixturing has been adopted that extends beyond the approach taken for the Engineering Test Stand (ETS). For the ETS, each substrate, including spares, has dedicated mounting hardware that is used exclusively for each element. In exchange for a reduced risk of mounting-induced deformation, this incurred substantial expense and precluded optics from using interchangeable tooling. For the current High NA camera, we have adopted an approach that employs interchangeable mounting hardware that can be used for any of the substrates

  17. Site-specific cleavage/packaging of herpes simplex virus DNA and the selective maturation of nucleocapsids containing full-length viral DNA

    PubMed Central

    Vlazny, Donald A.; Kwong, Ann; Frenkel, Niza

    1982-01-01

    Defective genomes present in serially passaged herpes simplex virus (HSV) stocks have been shown to consist of tandemly arranged repeat units containing limited sets of the standard virus DNA sequences. Invariably, the HSV defective genomes terminate with the right (S component) terminus of HSV DNA. Because the oligomeric forms can arise from a single repeat unit, it has been concluded that the defective genomes arise by a rolling circle mechanism of replication. We now report on our studies of defective genomes packaged in viral capsids accumulating in the nuclei and in mature virions (enveloped capsids) translocated into the cytoplasm of cells infected with serially passaged virus. These studies have revealed that, upon electrophoresis in agarose gels, the defective genomes prepared from cytoplasmic virions comigrated with nondefective standard virus DNA (Mr 100 × 106). In contrast, DNA prepared from capsids accumulating in nuclei consisted of both full-length defective virus DNA molecules and smaller DNA molecules of discrete sizes, ranging in Mr from 5.5 to 100 × 106. These smaller DNA species were shown to consist of different integral numbers (from 1 to approximately 18) of defective genome repeat units and to terminate with sequences corresponding to the right terminal sequences of HSV DNA. We conclude on the basis of these studies that (i) sequences from the right end of standard virus DNA contain a recognition signal for the cleavage and packaging of concatemeric viral DNA, (ii) the sequence-specific cleavage is either a prerequisite for or occurs during the entry of viral DNA into capsid structures, and (iii) DNA molecules significantly shorter than full-length standard viral DNA can become encapsidated within nuclear capsids provided they contain the cleavage/packaging signal. However, capsids containing DNA molecules significantly shorter than standard virus DNA are not translocated into the cytoplasm. Images PMID:6280181

  18. Fabric phase sorptive extraction: An innovative sample preparation approach applied to the analysis of specific migration from food packaging.

    PubMed

    Aznar, M; Alfaro, P; Nerin, C; Kabir, A; Furton, K G

    2016-09-14

    Additives added to food packaging materials can migrate to food in contact with them during storage and shelf life. A novel simple, fast and sensitive analyte extraction method based on fabric phase sorptive extraction (FPSE), followed by analysis using ultra-high performance liquid chromatography and mass spectrometry detection (UPLC-MS) was applied to the analysis of 18 common non-volatile plastic additives. Three FPSE media coated with different sol-gel sorbents characterized with different polarities including sol-gel poly(dimethylsiloxane), sol-gel poly(ethylene glycol) and sol-gel poly(tetrahydrofuran) were studied. All three FPSE media showed very satisfactory results. In general, compounds with low logP values seemed to have higher enrichment factors (EFs), especially with poly(tetrahydrofuran) and poly(ethylene glycol) media. For compounds with high logP values, the use of sol-gel poly(dimethylsiloxane) improved the enrichment capacity. Sample preparation time was optimized at 20 min for sample extraction and 10 min for solvent desorption. Acetonitrile was selected as desorption solvent since recoveries were over 70% for 13 out of 18 selected compounds in all FPSE media. The best extraction recovery values were obtained when compounds were dissolved in aqueous acetic acid solution (3%), where 17 out of 18 compounds showed improvement in their signal intensity after FPSE extraction and 10 obtained enrichment factors above 3 for all the tested FPSE media. When FPSE extracts were concentrated under nitrogen, 11 out of 18 compounds reached EFs values above 100. PMID:27566344

  19. Battery packaging - Technology review

    SciTech Connect

    Maiser, Eric

    2014-06-16

    This paper gives a brief overview of battery packaging concepts, their specific advantages and drawbacks, as well as the importance of packaging for performance and cost. Production processes, scaling and automation are discussed in detail to reveal opportunities for cost reduction. Module standardization as an additional path to drive down cost is introduced. A comparison to electronics and photovoltaics production shows 'lessons learned' in those related industries and how they can accelerate learning curves in battery production.

  20. Battery packaging - Technology review

    NASA Astrophysics Data System (ADS)

    Maiser, Eric

    2014-06-01

    This paper gives a brief overview of battery packaging concepts, their specific advantages and drawbacks, as well as the importance of packaging for performance and cost. Production processes, scaling and automation are discussed in detail to reveal opportunities for cost reduction. Module standardization as an additional path to drive down cost is introduced. A comparison to electronics and photovoltaics production shows "lessons learned" in those related industries and how they can accelerate learning curves in battery production.

  1. Scoring Package

    National Institute of Standards and Technology Data Gateway

    NIST Scoring Package (PC database for purchase)   The NIST Scoring Package (Special Database 1) is a reference implementation of the draft Standard Method for Evaluating the Performance of Systems Intended to Recognize Hand-printed Characters from Image Data Scanned from Forms.

  2. 7 CFR 58.626 - Packaging equipment.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Packaging equipment. 58.626 Section 58.626 Agriculture....626 Packaging equipment. Packaging equipment designed to mechanically fill and close single service... Standards for Equipment for Packaging Frozen Desserts and Cottage Cheese. Quality Specifications for...

  3. 7 CFR 58.626 - Packaging equipment.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Packaging equipment. 58.626 Section 58.626 Agriculture....626 Packaging equipment. Packaging equipment designed to mechanically fill and close single service... Standards for Equipment for Packaging Frozen Desserts and Cottage Cheese. Quality Specifications for...

  4. 7 CFR 58.626 - Packaging equipment.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Packaging equipment. 58.626 Section 58.626 Agriculture....626 Packaging equipment. Packaging equipment designed to mechanically fill and close single service... Standards for Equipment for Packaging Frozen Desserts and Cottage Cheese. Quality Specifications for...

  5. SU-C-201-06: Utility of Quantitative 3D SPECT/CT Imaging in Patient Specific Internal Dosimetry of 153-Samarium with GATE Monte Carlo Package

    SciTech Connect

    Fallahpoor, M; Abbasi, M; Sen, A; Parach, A; Kalantari, F

    2015-06-15

    Purpose: Patient-specific 3-dimensional (3D) internal dosimetry in targeted radionuclide therapy is essential for efficient treatment. Two major steps to achieve reliable results are: 1) generating quantitative 3D images of radionuclide distribution and attenuation coefficients and 2) using a reliable method for dose calculation based on activity and attenuation map. In this research, internal dosimetry for 153-Samarium (153-Sm) was done by SPECT-CT images coupled GATE Monte Carlo package for internal dosimetry. Methods: A 50 years old woman with bone metastases from breast cancer was prescribed 153-Sm treatment (Gamma: 103keV and beta: 0.81MeV). A SPECT/CT scan was performed with the Siemens Simbia-T scanner. SPECT and CT images were registered using default registration software. SPECT quantification was achieved by compensating for all image degrading factors including body attenuation, Compton scattering and collimator-detector response (CDR). Triple energy window method was used to estimate and eliminate the scattered photons. Iterative ordered-subsets expectation maximization (OSEM) with correction for attenuation and distance-dependent CDR was used for image reconstruction. Bilinear energy mapping is used to convert Hounsfield units in CT image to attenuation map. Organ borders were defined by the itk-SNAP toolkit segmentation on CT image. GATE was then used for internal dose calculation. The Specific Absorbed Fractions (SAFs) and S-values were reported as MIRD schema. Results: The results showed that the largest SAFs and S-values are in osseous organs as expected. S-value for lung is the highest after spine that can be important in 153-Sm therapy. Conclusion: We presented the utility of SPECT-CT images and Monte Carlo for patient-specific dosimetry as a reliable and accurate method. It has several advantages over template-based methods or simplified dose estimation methods. With advent of high speed computers, Monte Carlo can be used for treatment planning

  6. The 3,6 m Indo-Belgian Devasthal Optical Telescope: the hydrostatic azimuth bearing

    NASA Astrophysics Data System (ADS)

    de Ville, Jonathan; Piérard, Maxime; Bastin, Christian

    2012-09-01

    AMOS SA has been awarded of the contract for the design, manufacturing, assembly, tests and on site installation (Devasthal, Nainital in central Himalayan region) of the 3.6 m Indo-Belgian Devasthal Optical Telescope (IDOT). The telescope has a Ritchey-Chrétien optical configuration with a Cassegrain focus equipped with one axial port and two side ports. The primary mirror is a meniscus active mirror. The mount is an Alt-Az type with for the azimuth axis a 5 m diameter hydrostatic track. This paper presents the solution adopted by AMOS to meet the specific requirements for the azimuth axis. The track is designed to be able to control the positioning of the telescope around the azimuth axis with an accuracy of 0.05 arc second for all tracking configurations. The challenge came from this tight accuracy with a mass in rotation weighting 125 tons. The azimuth track was mounted and tested in AMOS workshop; the tests and performances are also discussed.

  7. Packaging Materials

    NASA Astrophysics Data System (ADS)

    Frear, Darrel

    This chapter is a high-level overview of the materials used in an electronic package including: metals used as conductors in the package, ceramics and glasses used as dielectrics or insulators and polymers used as insulators and, in a composite form, as conductors. There is a need for new materials to meet the ever-changing requirements for high-speed digital and radio-frequency (RF) applications. There are different requirements for digital and RF packages that translate into the need for unique materials for each application. The interconnect and dielectric (insulating) requirements are presented for each application and the relevant materials properties and characteristics are discussed. The fundamental materials characteristics are: dielectric constant, dielectric loss, thermal and electric conductivity, resistivity, moisture absorption, glass-transition temperature, strength, time-dependent deformation (creep), and fracture toughness. The materials characteristics and properties are dependant on how they are processed to form the electronic package so the fundamentals of electronic packaging processes are discussed including wirebonding, solder interconnects, flip-chip interconnects, underfill for flip chip and overmolding. The relevant materials properties are given along with requirements (including environmentally friendly Pb-free packages) that require new materials to be developed to meet future electronics needs for both digital and RF applications.

  8. A Ribonucleoprotein Complex Protects the Interleukin-6 mRNA from Degradation by Distinct Herpesviral Endonucleases

    PubMed Central

    Muller, Mandy; Hutin, Stephanie; Marigold, Oliver; Li, Kathy H.; Burlingame, Al; Glaunsinger, Britt A.

    2015-01-01

    During lytic Kaposi’s sarcoma-associated herpesvirus (KSHV) infection, the viral endonuclease SOX promotes widespread degradation of cytoplasmic messenger RNA (mRNA). However, select mRNAs escape SOX-induced cleavage and remain robustly expressed. Prominent among these is interleukin-6 (IL-6), a growth factor important for survival of KSHV infected B cells. IL-6 escape is notable because it contains a sequence within its 3’ untranslated region (UTR) that can confer protection when transferred to a SOX-targeted mRNA, and thus overrides the endonuclease targeting mechanism. Here, we pursued how this protective RNA element functions to maintain mRNA stability. Using affinity purification and mass spectrometry, we identified a set of proteins that associate specifically with the protective element. Although multiple proteins contributed to the escape mechanism, depletion of nucleolin (NCL) most severely impacted protection. NCL was re-localized out of the nucleolus during lytic KSHV infection, and its presence in the cytoplasm was required for protection. After loading onto the IL-6 3’ UTR, NCL differentially bound to the translation initiation factor eIF4H. Disrupting this interaction, or depleting eIF4H, reinstated SOX targeting of the RNA, suggesting that interactions between proteins bound to distant regions of the mRNA are important for escape. Finally, we found that the IL-6 3’ UTR was also protected against mRNA degradation by the vhs endonuclease encoded by herpes simplex virus, despite the fact that its mechanism of mRNA targeting is distinct from SOX. These findings highlight how a multitude of RNA-protein interactions can impact endonuclease targeting, and identify new features underlying the regulation of the IL-6 mRNA. PMID:25965334

  9. A ribonucleoprotein complex protects the interleukin-6 mRNA from degradation by distinct herpesviral endonucleases.

    PubMed

    Muller, Mandy; Hutin, Stephanie; Marigold, Oliver; Li, Kathy H; Burlingame, Al; Glaunsinger, Britt A

    2015-05-01

    During lytic Kaposi's sarcoma-associated herpesvirus (KSHV) infection, the viral endonuclease SOX promotes widespread degradation of cytoplasmic messenger RNA (mRNA). However, select mRNAs escape SOX-induced cleavage and remain robustly expressed. Prominent among these is interleukin-6 (IL-6), a growth factor important for survival of KSHV infected B cells. IL-6 escape is notable because it contains a sequence within its 3' untranslated region (UTR) that can confer protection when transferred to a SOX-targeted mRNA, and thus overrides the endonuclease targeting mechanism. Here, we pursued how this protective RNA element functions to maintain mRNA stability. Using affinity purification and mass spectrometry, we identified a set of proteins that associate specifically with the protective element. Although multiple proteins contributed to the escape mechanism, depletion of nucleolin (NCL) most severely impacted protection. NCL was re-localized out of the nucleolus during lytic KSHV infection, and its presence in the cytoplasm was required for protection. After loading onto the IL-6 3' UTR, NCL differentially bound to the translation initiation factor eIF4H. Disrupting this interaction, or depleting eIF4H, reinstated SOX targeting of the RNA, suggesting that interactions between proteins bound to distant regions of the mRNA are important for escape. Finally, we found that the IL-6 3' UTR was also protected against mRNA degradation by the vhs endonuclease encoded by herpes simplex virus, despite the fact that its mechanism of mRNA targeting is distinct from SOX. These findings highlight how a multitude of RNA-protein interactions can impact endonuclease targeting, and identify new features underlying the regulation of the IL-6 mRNA. PMID:25965334

  10. Hanford Site radioactive hazardous materials packaging directory

    SciTech Connect

    McCarthy, T.L.

    1995-12-01

    The Hanford Site Radioactive Hazardous Materials Packaging Directory (RHMPD) provides information concerning packagings owned or routinely leased by Westinghouse Hanford Company (WHC) for offsite shipments or onsite transfers of hazardous materials. Specific information is provided for selected packagings including the following: general description; approval documents/specifications (Certificates of Compliance and Safety Analysis Reports for Packaging); technical information (drawing numbers and dimensions); approved contents; areas of operation; and general information. Packaging Operations & Development (PO&D) maintains the RHMPD and may be contacted for additional information or assistance in obtaining referenced documentation or assistance concerning packaging selection, availability, and usage.

  11. Bonding and magnetism in nanosized graphene molecules: Singlet states of zigzag edged hexangulenes C6m2H6m(m =2,3,…,10)

    NASA Astrophysics Data System (ADS)

    Philpott, Michael R.; Kawazoe, Yoshiyuki

    2009-12-01

    A novel molecular phenomenon is predicted on the basis of trends identified in an ab initio density functional theory study of the electronic and geometric structure of the hexagonal shaped zigzag edged graphene hydrocarbon molecules C6m2H6m(m =2,…,10). Electrons in the interior organize to form a graphene core that grows with edge size m. Electrons in the highest occupied molecular orbital levels, localized primarily on the perimeter carbons, polarize the interior atoms with a intensity that decays rapidly with distance from the perimeter. Three distinctive bond length patterns emerge: (i) a central graphene core that grows with size m; (ii) shape-similar transverse and radial bond length patterns on interior rows close to the edges; and (iii) quinoidal bonds radiating from each apex that link adjacent edges. Concomitant with these changes are: (i) a monotonic decrease in atomic charge from center to perimeter and (ii) relegation of spin in diradical states to the outer atomic rows of the bipartite lattice.

  12. Bonding and magnetism in nanosized graphene molecules: Singlet states of zigzag edged hexangulenes C(6m(2) )H(6m)(m=2,3,...,10).

    PubMed

    Philpott, Michael R; Kawazoe, Yoshiyuki

    2009-12-01

    A novel molecular phenomenon is predicted on the basis of trends identified in an ab initio density functional theory study of the electronic and geometric structure of the hexagonal shaped zigzag edged graphene hydrocarbon molecules C(6m(2) )H(6m)(m=2,...,10). Electrons in the interior organize to form a graphene core that grows with edge size m. Electrons in the highest occupied molecular orbital levels, localized primarily on the perimeter carbons, polarize the interior atoms with a intensity that decays rapidly with distance from the perimeter. Three distinctive bond length patterns emerge: (i) a central graphene core that grows with size m; (ii) shape-similar transverse and radial bond length patterns on interior rows close to the edges; and (iii) quinoidal bonds radiating from each apex that link adjacent edges. Concomitant with these changes are: (i) a monotonic decrease in atomic charge from center to perimeter and (ii) relegation of spin in diradical states to the outer atomic rows of the bipartite lattice. PMID:19968359

  13. Green Packaging Management of Logistics Enterprises

    NASA Astrophysics Data System (ADS)

    Zhang, Guirong; Zhao, Zongjian

    From the connotation of green logistics management, we discuss the principles of green packaging, and from the two levels of government and enterprises, we put forward a specific management strategy. The management of green packaging can be directly and indirectly promoted by laws, regulations, taxation, institutional and other measures. The government can also promote new investment to the development of green packaging materials, and establish specialized institutions to identify new packaging materials, standardization of packaging must also be accomplished through the power of the government. Business units of large scale through the packaging and container-based to reduce the use of packaging materials, develop and use green packaging materials and easy recycling packaging materials for proper packaging.

  14. Individualized Learning Package about Etching.

    ERIC Educational Resources Information Center

    Sauer, Michael J.

    An individualized learning package provides step-by-step instruction in the fundamentals of the etching process. Thirteen specific behavioral objectives are listed. A pretest, consisting of matching 15 etching terms with their definitions, is provided along with an answer key. The remainder of the learning package teaches the 13 steps of the…

  15. Hazardous materials package performance regulations

    SciTech Connect

    Russell, N. A.; Glass, R. E.; McClure, J. D.; Finley, N. C.

    1991-01-01

    This paper discusses a hazardous materials Hazmat Packaging Performance Evaluation (HPPE) project being conducted at Sandia National Laboratories for the US Department of Transportation Research Special Programs Administration (DOT-RSPA) to look at the subset of bulk packagings that are larger than 2000 gallons. The objectives of this project are to evaluate current hazmat specification packagings and develop supporting documentation for determining performance requirements for packagings in excess of 2000 gallons that transport hazardous materials that have been classified as extremely toxic by inhalation (METBI).

  16. 49 CFR 178.915 - General Large Packaging standards.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false General Large Packaging standards. 178.915 Section... MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR PACKAGINGS Large Packagings Standards § 178.915 General Large Packaging standards. (a) Each Large Packaging must...

  17. 49 CFR 178.915 - General Large Packaging standards.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false General Large Packaging standards. 178.915 Section... MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR PACKAGINGS Large Packagings Standards § 178.915 General Large Packaging standards. (a) Each Large Packaging must...

  18. 49 CFR 178.915 - General Large Packaging standards.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false General Large Packaging standards. 178.915 Section... MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR PACKAGINGS Large Packagings Standards § 178.915 General Large Packaging standards. (a) Each Large Packaging must...

  19. 49 CFR 178.915 - General Large Packaging standards.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false General Large Packaging standards. 178.915 Section... MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR PACKAGINGS Large Packagings Standards § 178.915 General Large Packaging standards. (a) Each Large Packaging must...

  20. System packager strategies

    SciTech Connect

    Hennagir, T.

    1995-03-01

    Advances in combined equipment technologies, the ability to supply fuel flexibility and new financial support structures are helping power systems packagers meet a diverse series of client and project needs. Systems packagers continue to capture orders for various size power plants around the globe. A competitive buyer`s market remains the order of the day. In cogeneration markets, clients continue to search for efficiency rather than specific output for inside-the-fence projects. Letter-perfect service remains a requisite as successful suppliers strive to meet customers` ever-changing needs for thermal and power applications.

  1. Packaging signals in alphaviruses.

    PubMed

    Frolova, E; Frolov, I; Schlesinger, S

    1997-01-01

    Alphaviruses synthesize large amounts of both genomic and subgenomic RNA in infected cells, but usually only the genomic RNA is packaged. This implies the existence of an encapsidation or packaging signal which would be responsible for selectivity. Previously, we had identified a region of the Sindbis virus genome that interacts specifically with the viral capsid protein. This 132-nucleotide (nt) fragment lies within the coding region of the nsP1 gene (nt 945 to 1076). We proposed that the 132-mer is important for capsid recognition and initiates the formation of the viral nucleocapsid. To study the encapsidation of Sindbis virus RNAs in infected cells, we designed a new assay that uses the self-replicating Sindbis virus genomes (replicons) which lack the viral structural protein genes and contain heterologous sequences under the control of the subgenomic RNA promoter. These replicons can be packaged into viral particles by using defective helper RNAs that contain the structural protein genes (P. Bredenbeek, I. Frolov, C. M. Rice, and S. Schlesinger, J. Virol. 67:6439-6446, 1993). Insertion of the 132-mer into the subgenomic RNA significantly increased the packaging of this RNA into viral particles. We have used this assay and defective helpers that contain the structural protein genes of Ross River virus (RRV) to investigate the location of the encapsidation signal in the RRV genome. Our results show that there are several fragments that could act as packaging signals. They are all located in a different region of the genome than the signal for the Sindbis virus genome. For RRV, the strongest packaging signal lies between nt 2761 and 3062 in the nsP2 gene. This is the same region that was proposed to contain the packaging signal for Semliki Forest virus genomic RNA. PMID:8985344

  2. Packaged Food

    NASA Technical Reports Server (NTRS)

    1976-01-01

    After studies found that many elderly persons don't eat adequately because they can't afford to, they have limited mobility, or they just don't bother, Innovated Foods, Inc. and JSC developed shelf-stable foods processed and packaged for home preparation with minimum effort. Various food-processing techniques and delivery systems are under study and freeze dried foods originally used for space flight are being marketed. (See 77N76140)

  3. 49 CFR 178.3 - Marking of packagings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Marking of packagings. 178.3 Section 178.3... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR PACKAGINGS § 178.3 Marking of packagings. (a) Each packaging represented as manufactured to a DOT specification or a UN standard must...

  4. 49 CFR 178.3 - Marking of packagings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Marking of packagings. 178.3 Section 178.3... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR PACKAGINGS § 178.3 Marking of packagings. (a) Each packaging represented as manufactured to a DOT specification or a UN standard must...

  5. 49 CFR 178.3 - Marking of packagings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Marking of packagings. 178.3 Section 178.3... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS SPECIFICATIONS FOR PACKAGINGS § 178.3 Marking of packagings. (a) Each packaging represented as manufactured to a DOT specification or...

  6. Effects of high Z probe on plasma behavior in HT-6M tokamak

    NASA Astrophysics Data System (ADS)

    Li, J.; Gong, X.; Luo, L.; Yin, F. X.; Noda, N.; Wan, B.; Xu, W.; Gao, X.; Yin, F.; Jiang, J. G.; Wu, Z.; Zhao, J. Y.; Wu, M.; Liu, S.; Han, Y.

    1997-02-01

    Molybdenum and tungsten probes have been tested in HT-6M tokamak under various discharge conditions aiming to find out the conditions in which high Z PFC can be used without serious degradation of core plasma performance. In normal OH discharges, the degradation of core plasma performance was found only when the probe was inserted beyond 3.0 cm inside the last closed flux surface (LCFS). The plasma performance did not change with positive biasing to the probe, whereas central Te degraded during negative biasing of -100 V. The insertion of the Mo probe to 1.5 cm inside the LCFS made a change in the threshold power of the L-H transition in EOH discharges. These results suggest a certain operation range of the H-mode in the EOH discharge with the Mo probe in HT-6M.

  7. Enclosure design for the ARIES 3.6m optical telescope

    NASA Astrophysics Data System (ADS)

    Pandey, A. K.; Shukla, Vishal; Bangia, Tarun; Raskar, R. D.; Kulkarni, R. R.; Ghanti, A. S.

    2012-09-01

    A 3.6-m, f/9 optical telescope is planned to be installed at Devasthal, India (Latitude:29° 21' 40'' N, Longitude: 79° 41' 04'' E, Altitude: 2450 m above msl). The telescope has Cassegrain focus and alt-azimuth mount. The design of the telescope enclosure and the auxiliary building includes a fixed base enclosure, a telescope pier, a rotating dome structure, an auxiliary building, ventilation and component handling systems. The design is optimized for thermal, mechanical, structural, as well as for telescope installation and maintenance requirements. The design aims to provide seeing limited images within the telescope enclosure. This paper presents design of the 3.6m telescope enclosure.

  8. Construction of 3.6m ARIES telescope enclosure with eccentric pier at Devasthal, Nainital

    NASA Astrophysics Data System (ADS)

    Bangia, Tarun

    Space optimized enclosure with eccentric pier for 3.6m ARIES telescope presents construction challenges at the unique observing site of Devasthal, Nainital, India. Enclosure comprises of about 16.5m diameter and 14m high insulated steel framed cylindrical dome rotating on a 14m high stationery dome supporting structure and a 24m × 12m extension structure building for accommodating aluminizing plant and ventilation system etc. Great deal of manual and mechanical excavation was carried out at the rocky site using rock breaking and JCB machines. Foundation bolts for columns of dome supporting structure and extension structure building were grouted after alignment with total station. A 7m diameter hollow cylindrical pier isolated from other structures and 1.85m eccentric with dome center designed due to space limitation at site is being casted for mounting 150 MT mass of the largest 3.6m telescope in the country. A 7m diameter template was fabricated for 3.6m pier top. Most of enclosure components are manufactured and tested in works before assembly/erection at site. Dome drive was tested with dummy loads using VVVF drive with 6 drive and 12 idler wheel assemblies at works to simulate dome weight and smooth operation before erection at site. A 4.2m wide motorized windscreen is being manufactured with a special grade synthetic fabric to withstand wind speed up to 15m/s.

  9. The Major Human Immunodeficiency Virus Type 2 (HIV-2) Packaging Signal Is Present on All HIV-2 RNA Species: Cotranslational RNA Encapsidation and Limitation of Gag Protein Confer Specificity

    PubMed Central

    Griffin, Stephen D. C.; Allen, Jane F.; Lever, Andrew M. L.

    2001-01-01

    Deletion of a region of the human immunodeficiency virus type 2 (HIV-2) 5′ leader RNA reduces genomic RNA encapsidation to about 5% that of wild-type virus with no defect in viral protein production but severely limits virus spread in Jurkat T cells, indicating that this region contains a major cis-acting encapsidation signal, or psi (Ψ). Being upstream of the major splice donor, it is present on all viral transcripts. We have shown that HIV-2 selects its genomic RNA for encapsidation cotranslationally, rendering wild-type HIV-2 unable to encapsidate vector RNAs in trans . Virus with Ψ deleted, however, encapsidates an HIV-2 vector, demonstrating competition for Gag protein. HIV-2 overcomes the lack of packaging signal location specificity by two novel mechanisms, cotranslational packaging and competition for limiting Gag polyprotein. PMID:11711596

  10. Radioactive material packaging performance testing

    SciTech Connect

    Romano, T.

    1992-06-01

    In an effort to provide uniform packaging of hazardous material on an international level, recommendations for the transport of dangerous goods have been developed by the United Nations. These recommendations are performance oriented and contrast with a large number of packaging specifications in the US Department of Transportation's hazard materials regulations. This dual system presents problems when international shipments enter the US Department of Transportation's system. Faced with the question of continuing a dual system or aligning with the international system, the Research and Special Programs Administration of the US Department of Transportation responded with Docket HM-181. This began the transition toward the international transportation system. Following close behind is Docket HM-169A, which addressed low specific activity radioactive material packaging. This paper will discuss the differences between performance-oriented and specification packaging, the transition toward performance-oriented packaging by the US Department of Transportation, and performance-oriented testing of radioactive material packaging by Westinghouse Hanford Company. Dockets HM-181 and HM-169A will be discussed along with Type A (low activity) and Type B (high activity) radioactive material packaging evaluations.

  11. Radioactive material packaging performance testing

    SciTech Connect

    Romano, T.

    1992-06-01

    In an effort to provide uniform packaging of hazardous material on an international level, recommendations for the transport of dangerous goods have been developed by the United Nations. These recommendations are performance oriented and contrast with a large number of packaging specifications in the US Department of Transportation`s hazard materials regulations. This dual system presents problems when international shipments enter the US Department of Transportation`s system. Faced with the question of continuing a dual system or aligning with the international system, the Research and Special Programs Administration of the US Department of Transportation responded with Docket HM-181. This began the transition toward the international transportation system. Following close behind is Docket HM-169A, which addressed low specific activity radioactive material packaging. This paper will discuss the differences between performance-oriented and specification packaging, the transition toward performance-oriented packaging by the US Department of Transportation, and performance-oriented testing of radioactive material packaging by Westinghouse Hanford Company. Dockets HM-181 and HM-169A will be discussed along with Type A (low activity) and Type B (high activity) radioactive material packaging evaluations.

  12. Reflective Packaging

    NASA Technical Reports Server (NTRS)

    1994-01-01

    The aluminized polymer film used in spacecraft as a radiation barrier to protect both astronauts and delicate instruments has led to a number of spinoff applications. Among them are aluminized shipping bags, food cart covers and medical bags. Radiant Technologies purchases component materials and assembles a barrier made of layers of aluminized foil. The packaging reflects outside heat away from the product inside the container. The company is developing new aluminized lines, express mailers, large shipping bags, gel packs and insulated panels for the building industry.

  13. Nanocomposite Sensors for Food Packaging

    NASA Astrophysics Data System (ADS)

    Avella, Maurizio; Errico, Maria Emanuela; Gentile, Gennaro; Volpe, Maria Grazia

    Nowadays nanotechnologies applied to the food packaging sector find always more applications due to a wide range of benefits that they can offer, such as improved barrier properties, improved mechanical performance, antimicrobial properties and so on. Recently many researches are addressed to the set up of new food packaging materials, in which polymer nanocomposites incorporate nanosensors, developing the so-called "smart" packaging. Some examples of nanocomposite sensors specifically realised for the food packaging industry are reported. The second part of this work deals with the preparation and characterisation of two new polymer-based nanocomposite systems that can be used as food packaging materials. Particularly the results concerning the following systems are illustrated: isotactic polypropylene (iPP) filled with CaCO3 nanoparticles and polycaprolactone (PCL) filled with SiO2 nanoparticles.

  14. Romanian experience on packaging testing

    SciTech Connect

    Vieru, G.

    2007-07-01

    With more than twenty years ago, the Institute for Nuclear Research Pitesti (INR), through its Reliability and Testing Laboratory, was licensed by the Romanian Nuclear Regulatory Body- CNCAN and to carry out qualification tests [1] for packages intended to be used for the transport and storage of radioactive materials. Radioactive materials, generated by Romanian nuclear facilities [2] are packaged in accordance with national [3] and the IAEA's Regulations [1,6] for a safe transport to the disposal center. Subjecting these packages to the normal and simulating test conditions accomplish the evaluation and certification in order to prove the package technical performances. The paper describes the qualification tests for type A and B packages used for transport and storage of radioactive materials, during a period of 20 years of experience. Testing is used to substantiate assumption in analytical models and to demonstrate package structural response. The Romanian test facilities [1,3,6] are used to simulate the required qualification tests and have been developed at INR Pitesti, the main supplier of type A packages used for transport and storage of low radioactive wastes in Romania. The testing programme will continue to be a strong option to support future package development, to perform a broad range of verification and certification tests on radioactive material packages or component sections, such as packages used for transport of radioactive sources to be used for industrial or medical purposes [2,8]. The paper describes and contain illustrations showing some of the various tests packages which have been performed during certain periods and how they relate to normal conditions and minor mishaps during transport. Quality assurance and quality controls measures taken in order to meet technical specification provided by the design there are also presented and commented. (authors)

  15. Praxis I/O package

    SciTech Connect

    Holloway, F.W.; Sherman, T.A.

    1988-04-07

    The Praxis language specification, like Algol and Ada, does not specify any I/O statements. The intent was to provide a standard I/O package as a companion to the compiler. This would allow the user to substitute, or supplement, the I/O package, as needed, for specialized applications. Like Algol, however, Praxis provided only limited (text) I/O for several years. Ada, in contrast, provided a comprehensive standard I/O package from its inception. Digital Equipment Corporation's (DEC's) implementation of Ada, on their VAX family of computers, further supplemented this package with other packages which exploit the I/O facilities available under the VMS operating system. The Praxis I/O package described in this document has been modeled after DEC's implementation of Ada and provides a similar set of I/O facilities. Currently, the I/O package is supported only under VAX/VMS. The design of the package, however, is essentially independent of any operating system (with the exception of the module COMMAND IO). The VAX/VMS version of the I/O package fully exploits the vast I/O facilities which are provided under VAX/VMS and makes them directly available to the Praxis programmer. The design, prototype implementation, and draft documentation of the Praxis I/O Package was done by Tim Sherman as part of a University project in computer science. Subsequent work by both Tim and Fred Holloway lead to a more complete implementation, testing and development of example programs, and inclusion of the package into the Praxis compilers as their principal interface to RMS and VMS.

  16. EMCCD SPECKLE INTERFEROMETRY WITH THE 6 m TELESCOPE: ASTROMETRIC MEASUREMENTS, DIFFERENTIAL PHOTOMETRY, AND ORBITS

    SciTech Connect

    Docobo, Jose A.; Tamazian, Vakhtang S.; Melikian, Norair D. E-mail: vakhtang.tamazian@usc.e E-mail: nmelikia@bao.sci.a

    2010-10-15

    Results of the EMCCD-based speckle interferometric observations and differential photometry for 46 visual binaries obtained in 2007 June and July with the 6 m telescope of the Special Astrophysical Observatory (Russia) are presented. First preliminary orbits for COU 401, COU 1281, and COU 1037 as well as improved orbits for CHR 137, COU 100, COU 1136, COU 798, CHR 51, CHR 55, COU 315, COU 206, and ADS 13961, along with their dynamical mass estimates, are reported. On the basis of dynamical parallax information, first distance estimates for COU 100, COU 1136, COU 798, COU 206, and COU 1037 are calculated.

  17. Zn/gelled 6 M KOH/O 2 zinc-air battery

    NASA Astrophysics Data System (ADS)

    Mohamad, A. A.

    The gel electrolyte for the zinc-air cell was prepared by mixing hydroponics gel with a 6 M potassium hydroxide aqueous solution. The self-discharge of cells was characterized by measuring the open-circuit voltage. The effect of a discharge rate of 50 mA constant current on cell voltage and plateau hour, as well as the voltage-current and current density-power density were measured and analysed. The electrode degradation after discharge cycling was characterized by structural and surface methods. The oxidation of the electrode surface further blocked the utilization of the Zn anode and was identified as a cause for the failure of the cell.

  18. High-resolution fibre-fed spectrograph for the 6-m telescope. Polarimetric unit

    NASA Astrophysics Data System (ADS)

    Kukushkin, D. E.; Sazonenko, D. A.; Bakholdin, A. V.; Yushkin, M. V.; Bychkov, V. D.

    2016-04-01

    We report the computation of the design of a polarimetric unit for the optical scheme of the fiberfed high-resolution spectrograph for the 6-m Russian telescope.We discuss a variant of its integration into the design of conversion optics at the input of the fiber path if the instrument and estimate the efficiency of the entire pre-fiber optical system. The luminous efficiency of the assembly is equal to 80 and 90% when operated in the polarimetry and normal spectroscopic modes, respectively.We estimate the lower limit for the distorting instrumental effects of the polarimetric unit.

  19. Structural Testing of a 6m Hypersonic Inflatable Aerodynamic Decelerator System

    NASA Technical Reports Server (NTRS)

    Swanson, G. T.; Kazemba, C. D.; Johnson, R. K.; Hughes, S. J.; Calomino, A. M.

    2015-01-01

    NASA is developing low ballistic coefficient technologies to support the Nations long-term goal of landing humans on Mars. Current entry, decent, and landing technologies are not practical for this class of payloads due to geometric constraints dictated by current and future launch vehicle fairing limitations. Hypersonic Inflatable Aerodynamic Decelerators (HIADs) are being developed to circumvent this limitation and are now considered a leading technology to enable landing of heavy payloads on Mars. At the beginning of 2014, a 6m diameter HIAD inflatable structure with an integrated flexible thermal protection system (TPS) was subjected to a static load test series to verify its structural performance under flight-relevant loads. The inflatable structure was constructed into a 60 degree sphere-cone configuration using nine inflatable torus segments composed of fiber-reinforced thin films. The inflatable tori were joined together using adhesives and high-strength textile woven structural straps. These straps help distribute the load throughout the inflatable structure. The 6m flexible TPS was constructed using multiple layers of high performance materials that are designed to protect the inflatable structure from heat loads that would be seen in flight during atmospheric entry. A custom test fixture was constructed to perform the static load test series. The fixture consisted of a round structural tub with enough height and width to allow for displacement of the HIAD test article as loads were applied. The bottom of the tub rim had an airtight seal with the floor. The rigid centerbody of the HIAD was mounted to a pedestal in the center of the structural tub. Using an impermeable membrane draped over the HIAD test article, an airtight seal was created with the top rim of the static load tub. This seal allowed partial vacuum to be pulled beneath the HIAD resulting in a uniform static pressure load applied to the outer surface. Using this technique, the test article

  20. Spectral monitoring of NGC 4151 and 3C 390.3 at the 6 m telescope.

    NASA Astrophysics Data System (ADS)

    Shapovalova, A. I.; Burenkov, A. N.; Bochkarev, N. G.

    The results of spectral monitoring of the Seyfert galaxies NGC 4151 (1986 - 96) and 3C 390.3 (1995 - 96) obtained at the 6 m telescope are presented. The behaviour of the broad component profiles of Hβ and continuum is studied. Quasisimultaneous variations of the fluxes in the blue and red wings of Hβ in both galaxies are detected, which is indicative of the absence of considerable radial motions in BLR. The authors confirm the obtained by Veilleux and Zheng (1991) sinusoidal dependence with a period of ≡10 years for the ratios of the observed fluxes of the blue and red wings of Hβ in 3C 390.3 spectra.

  1. Progress in the 1.6 m New Solar Telescope in Big Bear

    NASA Astrophysics Data System (ADS)

    Goode, Philip R.; NST Team

    2006-06-01

    Progress in building the NST (New Solar Telescope) will be reported. The NST is a 1.6 m clear aperture, off-axis solar telescope. The telescope is scheduled to see first light at Big Bear Solar Observatory (BBSO) in April 2007, and is a joint effort of BBSO, the University of Hawaii, the Korea Astronomy & Space Science Institute and the University of Arizona.The telescope is off-axis to optimize low-contrast imaging, and will have a 3 arcminute field of view. Figuring and testing the figure of the large off-axis primary mirror presented unique problems. The NST (New Solar Telescope) will have wavefront sensor controlled, real-time active optics, and its light will feed BBSO's adaptive optics system, which in turn feeds infrared and visible light Fabry-Perot based polarimeters, as well as a real-time image processing system utilizing parallel processing.The NST replaces the current 0.6 m solar telescope at BBSO, and required a new, larger, vented dome with new thermal and telescope control systems.The complementary value of the telescope for upcoming space missions, such as SOLAR-B, STEREO and SDO will be discussed.

  2. DEVELOPMENT AND TESTING OF THE BLANTON CLAMSHELL CLOSUREFOR USE ON RADIOACTIVE MATERIAL PACKAGING DRUMS

    SciTech Connect

    Blanton, P

    2007-10-18

    This paper provides a brief history of the U.S. Type B 6M specification container, its introduction into U.S. Code of federal regulations and its scheduled elimination three decades later. The paper also presents development, testing and deployment by the Department of Energy (DOE) of an enhanced drum closure called the 'Blanton Clamshell' (patent pending) that was designed to replace the standard open-head C-ring closure for the 55- and 85-gallon drums described in the 6M specification to extend their safe use. Nuclear Filter Technology has the Exclusive License for Clamshell production. Drum packages utilizing the standard C-ring closure have been a main-stay for over a half of a century in the national and international nuclear industry for shipping radioactive materials and will remain so in the foreseeable future. Drum package use in the U.S. increased heavily in the 1950's with development of the Weapons Complex and subsequently the commercial nuclear reactor industry.

  3. High density packaging technology ultra thin package & new tab package

    NASA Astrophysics Data System (ADS)

    Nakagawa, Osamu; Shimamoto, Haruo; Ueda, Tetsuya; Shimomura, Kou; Hata, Tsutomu; Tachikawa, Toru; Fukushima, Jiro; Banjo, Toshinobu; Yamamoto, Isamu

    1989-09-01

    As electronic devices become more highly integrated, the demand for small, high pin count packages has been increasing. We have developed two new types of IC packages in response to this demand. One is an ultra thin small outline package (TSOP) which has been reduced in size from the standard SOP and the other, which uses Tape Automated Bonding (TAB) technology, is a super thin, high pin count TAB in cap (T.I.C.) package. In this paper, we present these packages and their features along with the technologies used to improve package reliability and TAB. Thin packages are vulnerable to high humidity exposure, especially after heat shock.1 The following items were therefore investigated in order to improve humidity resistance: (1) The molding compound thermal stress, (2) Water absorption into the molding compound and its effect on package cracking during solder dipping, (3) Chip attach pad area and its affect on package cracking, (4) Adhesion between molding resin and chip attach pad and its affect on humidity resistance. With the improvements made as a result of these investigations, the reliability of the new thin packages is similar to that of the standard thicker plastic packages.

  4. The Ettention software package.

    PubMed

    Dahmen, Tim; Marsalek, Lukas; Marniok, Nico; Turoňová, Beata; Bogachev, Sviatoslav; Trampert, Patrick; Nickels, Stefan; Slusallek, Philipp

    2016-02-01

    We present a novel software package for the problem "reconstruction from projections" in electron microscopy. The Ettention framework consists of a set of modular building-blocks for tomographic reconstruction algorithms. The well-known block iterative reconstruction method based on Kaczmarz algorithm is implemented using these building-blocks, including adaptations specific to electron tomography. Ettention simultaneously features (1) a modular, object-oriented software design, (2) optimized access to high-performance computing (HPC) platforms such as graphic processing units (GPU) or many-core architectures like Xeon Phi, and (3) accessibility to microscopy end-users via integration in the IMOD package and eTomo user interface. We also provide developers with a clean and well-structured application programming interface (API) that allows for extending the software easily and thus makes it an ideal platform for algorithmic research while hiding most of the technical details of high-performance computing. PMID:26686659

  5. 7 CFR 993.501 - Consumer package of prunes.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 8 2012-01-01 2012-01-01 false Consumer package of prunes. 993.501 Section 993.501... CALIFORNIA Pack Specification as to Size Definitions § 993.501 Consumer package of prunes. Consumer package of prunes means consumer package as defined in § 993.22. Effective Date Note: At 70 FR 30613, May...

  6. 7 CFR 993.501 - Consumer package of prunes.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 8 2014-01-01 2014-01-01 false Consumer package of prunes. 993.501 Section 993.501... CALIFORNIA Pack Specification as to Size Definitions § 993.501 Consumer package of prunes. Consumer package of prunes means consumer package as defined in § 993.22. Effective Date Note: At 70 FR 30613, May...

  7. 7 CFR 993.501 - Consumer package of prunes.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 8 2011-01-01 2011-01-01 false Consumer package of prunes. 993.501 Section 993.501... CALIFORNIA Pack Specification as to Size Definitions § 993.501 Consumer package of prunes. Consumer package of prunes means consumer package as defined in § 993.22. Effective Date Note: At 70 FR 30613, May...

  8. 7 CFR 993.501 - Consumer package of prunes.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 8 2013-01-01 2013-01-01 false Consumer package of prunes. 993.501 Section 993.501... CALIFORNIA Pack Specification as to Size Definitions § 993.501 Consumer package of prunes. Consumer package of prunes means consumer package as defined in § 993.22. Effective Date Note: At 70 FR 30613, May...

  9. 7 CFR 58.151 - Packaging and repackaging.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Packaging and repackaging. 58.151 Section 58.151... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Packaging and General Identification § 58.151 Packaging and repackaging. (a) Packaging dairy products or cutting and repackaging...

  10. 7 CFR 993.501 - Consumer package of prunes.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Consumer package of prunes. 993.501 Section 993.501... CALIFORNIA Pack Specification as to Size Definitions § 993.501 Consumer package of prunes. Consumer package of prunes means consumer package as defined in § 993.22. Effective Date Note: At 70 FR 30613, May...

  11. 7 CFR 58.151 - Packaging and repackaging.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Packaging and repackaging. 58.151 Section 58.151... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Packaging and General Identification § 58.151 Packaging and repackaging. (a) Packaging dairy products or cutting and repackaging...

  12. 7 CFR 58.151 - Packaging and repackaging.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Packaging and repackaging. 58.151 Section 58.151... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Packaging and General Identification § 58.151 Packaging and repackaging. (a) Packaging dairy products or cutting and repackaging...

  13. 7 CFR 58.151 - Packaging and repackaging.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Packaging and repackaging. 58.151 Section 58.151... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Packaging and General Identification § 58.151 Packaging and repackaging. (a) Packaging dairy products or cutting and repackaging...

  14. 49 CFR 178.503 - Marking of packagings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Marking of packagings. 178.503 Section 178.503... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR PACKAGINGS Non-bulk Performance-Oriented Packaging Standards § 178.503 Marking of packagings. (a) A manufacturer must mark every...

  15. 7 CFR 58.151 - Packaging and repackaging.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Packaging and repackaging. 58.151 Section 58.151... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Packaging and General Identification § 58.151 Packaging and repackaging. (a) Packaging dairy products or cutting and repackaging...

  16. Influence of Wind Buffeting on the 3.6 m Telescope

    NASA Astrophysics Data System (ADS)

    Griffin, S.; Haar, S.; Walker, E.; Whiting, A.; Williams, S.

    2013-09-01

    Unsteady wind loading is the largest dynamic loading on most large ground telescopes. The maximum operational windspeed not only sets requirements on the wind load rejection performance of the mount control system but also is a significant driver for tracker error rejection. In addition, turbulence due to the wind contributes to wavefront distortion. With the recent interest in daylight imaging, introduction of a baffle that reduces background light during the day may further accentuate wind loading on the 3.6 m telescope. The initial daylight configuration of the telescope has been to operate without a baffle and to use operational constraints to avoid angles close to the sun. This configuration offers reasonable daylight performance but is susceptible to stray light that limits achievable signal-to-noise ratio. Also under test is a unique baffled configuration where the telescope is shrouded to increase target signal-to-noise ratio. Traditional baffles increase jitter and wind loading due to increased exposed area to the wind and increase wavefront distortion due to thermal gradients introduced by the baffle. The 3.6 m telescope baffle has been designed out of an opaque fabric to limit the negative impacts on jitter and wavefront distortion while increasing signal-to-noise ratio for daylight imaging. The intent of the design is to limit high frequency transmission of wind loading by the relatively compliant fabric and to allow some circulation using the fabric's porosity to limit thermal gradients. The fabric design also facilitates the extension to a deployable design, since it is relatively easy to deploy and stow compared to a traditional approach. This paper will present analytical results predicting jitter and mount control performance with and without the baffle as well as signal-to-noise ratio predictions with and without the baffle. The jitter results will use measured wind loading in conjunction with a system line-of-sight model for performance

  17. Science packages

    NASA Astrophysics Data System (ADS)

    1997-01-01

    Primary science teachers in Scotland have a new updating method at their disposal with the launch of a package of CDi (Compact Discs Interactive) materials developed by the BBC and the Scottish Office. These were a response to the claim that many primary teachers felt they had been inadequately trained in science and lacked the confidence to teach it properly. Consequently they felt the need for more in-service training to equip them with the personal understanding required. The pack contains five disks and a printed user's guide divided up as follows: disk 1 Investigations; disk 2 Developing understanding; disks 3,4,5 Primary Science staff development videos. It was produced by the Scottish Interactive Technology Centre (Moray House Institute) and is available from BBC Education at £149.99 including VAT. Free Internet distribution of science education materials has also begun as part of the Global Schoolhouse (GSH) scheme. The US National Science Teachers' Association (NSTA) and Microsoft Corporation are making available field-tested comprehensive curriculum material including 'Micro-units' on more than 80 topics in biology, chemistry, earth and space science and physics. The latter are the work of the Scope, Sequence and Coordination of High School Science project, which can be found at http://www.gsh.org/NSTA_SSandC/. More information on NSTA can be obtained from its Web site at http://www.nsta.org.

  18. The 3,6 m Indo-Belgian Devasthal Optical Telescope: general description

    NASA Astrophysics Data System (ADS)

    Ninane, Nathalie; Flebus, Carlo; Kumar, Brijesh

    2012-09-01

    AMOS SA has been awarded of the contract for the design, manufacturing, assembly, tests and on site installation (Devasthal, Nainital in central Himalayan region) of the 3.6 m Indo-Belgian Devasthal Optical Telescope (IDOT). The telescope has Ritchey-Chrétien optical configuration with one axial and two side Cassegrain ports. The meniscus primary mirror is active and it is supported by pneumatic actuators. The azimuth axis system is equipped with hydrostatic bearing. The telescope was completely assembled and tested in AMOS workshop. This step is completed and successful. The telescope is now ready for shipment to Nainital. This paper describes the telescope and summarizes the test results performed at AMOS to demonstrate that the telescope satisfies the main system requirements.

  19. Mechanical characteristics of alloy AMg6M in broad temperature and strain-rate ranges

    SciTech Connect

    Krashchenko, V.P.; Dvoeglazov, G.A.; Ermolaev, G.V.; Rudnitskii, N.P.

    1986-02-01

    The authors study the mechanical properties of an aluminum-magnesium alloy in broad ranges of temperature and strain rate, and the change in hardness and dynamic modulus of elasticity in relation to temperature. The material chosen for study was alloy AMg6M. The heat treating process is described. The experimental data obtained on Micro-6, UVT-2, and UP-7 units is shown graphically. It is apparent that an increase in temperature is accompanied by a decrease in hardness, elastic modulus, and strength in general. Models are obtained and additional tests of specimens at the strain rate 3.3 X 10/sup -2/ sec/sup -1/ and different temperatures are conducted. The dependences must be calculated using all possible models, and the lowest resulting value must be chosen.

  20. Drop Simulation of 6M Drum with Locking-Ring Closure and Liquid Contents

    SciTech Connect

    Wu, T

    2006-04-17

    This paper presents the dynamic simulation of the 6M drum with a locking-ring type closure subjected to a 4.9-foot drop. The drum is filled with water to 98 percent of overflow capacity. A three dimensional finite-element model consisting of metallic, liquid and rubber gasket components is used in the simulation. The water is represented by a hydrodynamic material model in which the material's volume strength is determined by an equation of state. The explicit numerical method based on the theory of wave propagation is used to determine the combined structural response to the torque load for tightening the locking-ring closure and to the impact load due to the drop.

  1. The 1.6 m New Solar Telescope (NST) in Big Bear

    NASA Astrophysics Data System (ADS)

    Cao, W.

    2012-12-01

    The 1.6 m clear aperture, off-axis New Solar Telescope (NST) is in regular operation in Big Bear Solar Observatory. The NST is the first facility-class solar telescope built in the U.S. in a generation. The NST provides high resolution and high sensitivity observations of the solar photosphere and chromosphere in the visible and near infrared (NIR). A high order adaptive optics system delivers corrected light to an ensemble of state-of-the-art scientific instruments in the coude laboratory including the Broad-band Filter Imagers (BFIs), NIR Imaging Spectro-polarimeter (NIRIS), Visible Imaging Spectro-polarimeter (VIS) and Fast Imaging Solar Spectrograph (FISS). Some early scientific results from the NST will be presented, followed by a progress report on NST instrument development projects, as well as upgrades to existing instruments.

  2. The 1.6 m off-axis New Solar Telescope (NST) in Big Bear

    NASA Astrophysics Data System (ADS)

    Goode, Philip R.; Cao, Wenda

    2012-09-01

    The 1.6-m New Solar Telescope (NST) has been used to observe the Sun for more than three years with ever increasing capabilities as its commissioning phase winds down. The NST is the first facility-class solar telescope built in the U.S. in a generation, and it has an off-axis design as is planned for the 4 m Advanced Technology Solar Telescope. Lessons learned will be discussed. Current NST post-focus instrumentation includes adaptive optics (AO) feeding photometric and near-IR polarimetric sytems, as well as an imaging spectrograph. On-going instrumentation projects will be sketched, including Multi-Conjugate AO (MCAO), next generation (dual Fabry- Perot) visible light and near-IR polarimeters and a fully cryogenic spectrograph. Finally, recent observational results illustrating the high resolution capabilities of the NST will be shown.

  3. The EMCCD-based speckle interferometer of the BTA 6-m telescope: Description and first results

    NASA Astrophysics Data System (ADS)

    Maksimov, A. F.; Balega, Yu. Yu.; Dyachenko, V. V.; Malogolovets, E. V.; Rastegaev, D. A.; Semernikov, E. A.

    2009-07-01

    The description is given for the speckle interferometer of the BTA 6-m telescope of the SAO RAS based on a new detector with an electron multiplication CCD. The main components of the instrument are microscope objectives, interference filters and atmospheric dispersion correction prisms. The PhotonMAX-512B CCD camera using a back-illuminated CCD97 allows up to 20 speckle images (with 512×512 pix resolution) per second storage on the hard drive. Due to high quantum efficiency (93% in the maximum at 550 nm), and high transmission of its optical elements, the new camera can be used for diffraction-limited (0.02″) image reconstruction of 15 m stars under good seeing conditions. The main advantages of the new system over the previous generation BTA speckle interferometer are examined.

  4. Active optics correction forces for the VST 2.6m primary mirror

    NASA Astrophysics Data System (ADS)

    Schipani, P.; Perrotta, F.; Marty, L.

    2006-06-01

    In active optics systems obviously a fundamental role is played be the choice of polynomials to describe the primary mirror deformations. The well known Zernike polynomials are widely used because of their immediate interpretation in terms of optical aberrations. Nevertheless in an active optics correction system context, the choice of the so called "minimum energy modes" as the polynomials to represent the mechanical deformations is best justified by their derivation from mechanical properties. This is the approach followed for the 2.6m primary mirror of the VST telescope, to be hosted on top of the Cerro Paranal ESO observatory. The calibration forces to compensate a given amount of each aberration mode are computed and discussed.

  5. Structure and wear resistance of R6M5 steel based coatings

    NASA Astrophysics Data System (ADS)

    Gnyusov, S. F.; Ignatov, A. A.; Durakov, V. G.

    2010-08-01

    Features of the structure of R6M5 steel based coatings obtained by multiscan electron-beam fusion of a hardening composition in vacuum have been studied. It is established that the carbide subsystem of the hardened layer is characterized by a multimodal distribution of carbide particles with d 1 = 3.8 μm, d 2 = 0.65 μm, and d 3 < 0.25 μm. The volume fraction of M6C secondary carbide and retained matrix austenite can be controlled within broad limits by varying thermal parameters of the electron-beam fusion. An increase in the retained austenite fraction in the coating leads to improved wear resistance due to the γ → α' marten-site transformation during friction and the presence of dispersed secondary carbides inside the matrix grains.

  6. Construction and Test of 3.6 m Nb3Sn Racetrack Coils for LARP

    SciTech Connect

    Wanderer, P.; Ambrosio, G.; Anerella, M.; Barzi, E.; Bossert, R.; Caspi, S.; Cheng, D. W.; Cozzolino, J.; Dietderich, D.R.; Escallier, J.; Feher, S.; Ferracin, P.; Ganetis, G.; Ghosh, A. K.; Gupta, R. C.; Hafalia,, A. R.; Hannaford, C. R.; Joshi, P.; Kovach, P.; Lietzke, A. F.; Lizarazo, J.; Louie, W.; Marone, A.; McInturff, A.D.; Muratore, J.; Nobrega, F.; Sabbi, G.; Schmalzle, J.; Thomas, R.; Turrioni, D.

    2008-06-01

    Development of high-performance Nb{sub 3}Sn quadrupoles is one of the major goals of the LHC Accelerator Research Program (LARP). As part of this program, long racetrack magnets were made in order to check the fabrication steps for long Nb{sub 3}Sn coils, that the changes in coil length that take place during reaction and cooldown are correctly accounted for in the quadrupole design, and the use of a long aluminum shell for the support structure. This paper reports the construction of the first long Nb{sub 3}Sn magnet with racetrack coils 3.6 m long. The magnet reached a nominal 'plateau' at 9596 A after five quenches. This is about 90% of the estimated conductor limit. The peak field in the coils at this current was 11 T.

  7. Improved Ohmic confinement induced by multipulse turbulent heating in the Hefei Tokamak-6M

    NASA Astrophysics Data System (ADS)

    Xu, Yuhong; Yu, Chang-Xuan; Luo, J. R.; Mao, J. S.; Liu, B. H.; Li, J. G.; Liang, Y. F.; Jie, Y. X.; Wu, Z. W.

    1998-06-01

    The improved Ohmic confinement phase (H-mode) has been observed during the turbulent heating (TH) pulse on the Hefei Tokamak-6M (HT-6M) [World Survey of Activities in Controlled Fusion Research, Nuclear Fusion Special Supplement (International Atomic Energy Agency, Vienna, 1991), p. 190]. The electron temperature and density profiles become steeper, and a more negative radial electric field Er well is developed across the normal Ohmic phase (L-mode) to H-mode transition, at the plasma edge. The edge toroidal and poloidal velocities υφ and υθ and the main ion pressure gradient ∇Pi are substantially enhanced after the TH pulse. It is found that across the transition, υθ, υφ and ∇Pi all play significant roles for regulating the Er profile, and the negative well shape of Er in the H-mode is dominantly maintained by the poloidal rotation. The time evolution indicates that prior to the transition υθ plays a key role in inducing the rapid variations of the Er and its shear. The density fluctuation suppression is independent of the sign of the Er shear(Er') and Er curvature (Er″) and consistent with the theoretical models of Shaing et al. and Zhang and Mahajan, while the Er″ sign has an appreciable effect on the suppression of the plasma potential fluctuations. This fact reveals that the dependence of these two fluctuation suppressions on the Er shear are different, suggesting that the existing L→H transition theories which consider only a single fluctuating field should be improved.

  8. THERMAL TESTING OF 9977 GENERAL PURPOSE FISSILE PACKAGE USING A POOL FIRE

    SciTech Connect

    Smith, A; Cecil May, C; Lawrence Gelder, L; Glenn Abramczyk, G

    2007-02-15

    The 9977/9978 General Purpose Fissile Package (GPFP), has been designed as a cost-effective, user-friendly replacement for the DOT 6M Specification Package for transporting Plutonium and Uranium metals and oxides. To ensure the capability of the 9977 GPFP to withstand the regulatory crush test, urethane foam was chosen for the impact absorbing overpack. As part of the package development it was necessary to confirm that the urethane foam overpack would provide the required protection for the containment vessel during the thermal test portion of the Hypothetical Accident Conditions Sequential Tests. Development tests of early prototypes were performed, using a furnace. Based on the results of the development tests, detailed design enhancements were incorporated into the final design. Examples of the definitive 9977 design configuration were subjected to an all-engulfing pool fire test, as part of the HAC Sequential Tests, to support the application for certification. Testing has confirmed the package's ability to withstand the HAC thermal tests.

  9. 49 CFR 173.24a - Additional general requirements for non-bulk packagings and packages.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Group I packaging may be used for a Packing Group II material with a specific gravity not exceeding the... criteria can still be met with the higher specific gravity material; (ii) A Packing Group I packaging may be used for a Packing Group III material with a specific gravity not exceeding the greater of 2.7,...

  10. RH Packaging Program Guidance

    SciTech Connect

    Washington TRU Solutions, LLC

    2003-08-25

    -for-word steps in th is document, in sequence, including Notes and cautions. Site specific information may be included as necessary. The document, and revisions, must then be submitted to CBFO at sitedocuments@wipp.ws for approval. A copy of the approval letter from CBFO shall be available for audit purposes. Users may develop site-specific procedures addressing preoperational activities, quality assurance (QA), hoisting and rigging, and radiation health physics to be used with the instructions contained in this document. Users may recommend changes to this document by submitting their recommendations (in writing) to the WIPP M&O Contractor RH Packaging Maintenance Engineer for evaluation. If approved, the change(s) will be incorporated into this document for use by ALL users. Before first use and every 12 months after, user sites will be audited to this document to ensure compliance. They will also be audited within one year from the effective date of revisions to this document.

  11. Software packager user's guide

    NASA Technical Reports Server (NTRS)

    Callahan, John R.

    1995-01-01

    Software integration is a growing area of concern for many programmers and software managers because the need to build new programs quickly from existing components is greater than ever. This includes building versions of software products for multiple hardware platforms and operating systems, building programs from components written in different languages, and building systems from components that must execute on different machines in a distributed network. The goal of software integration is to make building new programs from existing components more seamless -- programmers should pay minimal attention to the underlying configuration issues involved. Libraries of reusable components and classes are important tools but only partial solutions to software development problems. Even though software components may have compatible interfaces, there may be other reasons, such as differences between execution environments, why they cannot be integrated. Often, components must be adapted or reimplemented to fit into another application because of implementation differences -- they are implemented in different programming languages, dependent on different operating system resources, or must execute on different physical machines. The software packager is a tool that allows programmers to deal with interfaces between software components and ignore complex integration details. The packager takes modular descriptions of the structure of a software system written in the package specification language and produces an integration program in the form of a makefile. If complex integration tools are needed to integrate a set of components, such as remote procedure call stubs, their use is implied by the packager automatically and stub generation tools are invoked in the corresponding makefile. The programmer deals only with the components themselves and not the details of how to build the system on any given platform.

  12. Evaluating the impact of scoring parameters on the structure of intra-specific genetic variation using RawGeno, an R package for automating AFLP scoring

    PubMed Central

    Arrigo, Nils; Tuszynski, Jarek W; Ehrich, Dorothee; Gerdes, Tommy; Alvarez, Nadir

    2009-01-01

    files to user-defined working binary matrices. RawGeno was implemented in an R CRAN package (with an user-friendly GUI) and can be found at . PMID:19171029

  13. Aristos Optimization Package

    2007-03-01

    Aristos is a Trilinos package for nonlinear continuous optimization, based on full-space sequential quadratic programming (SQP) methods. Aristos is specifically designed for the solution of large-scale constrained optimization problems in which the linearized constraint equations require iterative (i.e. inexact) linear solver techniques. Aristos' unique feature is an efficient handling of inexactness in linear system solves. Aristos currently supports the solution of equality-constrained convex and nonconvex optimization problems. It has been used successfully in the areamore » of PDE-constrained optimization, for the solution of nonlinear optimal control, optimal design, and inverse problems.« less

  14. Packaging Theory.

    ERIC Educational Resources Information Center

    Williams, Jeffrey

    1994-01-01

    Considers the recent flood of anthologies of literary criticism and theory as exemplifications of the confluence of pedagogical concerns, economics of publishing, and other historical factors. Looks specifically at how these anthologies present theory. Cites problems with their formatting theory and proposes alternative ways of organizing theory…

  15. First Results from 1.6 m Off-Axis Solar Telescope in Big Bear (Invited)

    NASA Astrophysics Data System (ADS)

    Goode, P. R.

    2009-12-01

    In early 2009 at Big Bear Solar Observatory, first light science observations were made with BBSO's NST (New Solar Telescope), which has a 1.6m clear aperture (0.06” resolution at 500 nm). After a brief introduction to some of the lessons learned in making the telescope, first light observations in TiO, Halpha, G-Band and 1.56 micron lines will be introduced with detailed results presented in other talks in this session, including joint observations with Hinode and other satellites. The NST has an off-axis Gregorian configuration consisting of a parabolic primary, heat-stop, elliptical secondary and diagonal flats. The focal ratio of the primary mirror is f/2.4, and the final ratio is f/50. The working wavelength range covers from 0.4 to 1.7 microns in the Coude Lab beneath the telescope and all wavelengths including the far infrared at the Nasmyth focus on the dome floor. Plans for the on-going commissioning phase will be sketched.

  16. Half sandwich structures of MCF6- (M = Ag and Au): An experimental and theoretical study

    NASA Astrophysics Data System (ADS)

    Sun, Zhang; Tang, Zichao; Gao, Zhen

    2013-01-01

    The metal-hexafluorobenzene anionic complexes of [MC6F6]- (M = Ag and Au) were produced from the reactions between metal cluster generated by laser ablation and the hexafluorobenzene seeded in argon carrier gas, and were studied by photoelectron spectroscopy (PES) and density functional theory (DFT). The adiabatic electron affinities (EAs) of these corresponding complexes are measured from the experimental PE spectra at 193 nm photon energy. Also, the calculated EAs and the calculated density of states (DOS) spectra of these complexes in the ground state are conducted, which are in good agreement with their experimental PE spectra. The most possible structures of the anions [AgC6F6]- and [AuC6F6]- are the half-sandwich structures with C6v symmetry, in which the metal atom is above the center of the C6F6 plane. Furthermore, the molecular orbital (MO) analysis of these species indicates that the additional electron of the anions binds on the metal.

  17. Imaging polarimetry of distant comets at the 6-m BTA telescope of the SAO RAS

    NASA Astrophysics Data System (ADS)

    Ivanova, Oleksandra; Afanasiev, Viktor; Rosenbush, Vera; Kiselev, Nikolai

    2016-07-01

    Results of the recent polarimetric observations of distant comets C/2013 V4 (Catalina), C/2014 A4 (SONEAR), C/2010 S1 (LINEAR), C/2010 R1 (LINEAR), and 29P/Schwassmann-Wachmann 1 are presented together with analysis of their photometry and spectroscopy. Observations were carried out at the 6-m telescope BTA of the SAO RAS with the multi-mode focal reducer SCORPIO-2 from 2011 to 2015. Comets were observed in the range of heliocentric distances from 4.2 to 7.0 AU and phase angles from 4.9 to 9.4 degrees. The maps of intensity and linear polarization over the coma are derived. The comets observed show a considerable activity at heliocentric distances far exceeding a zone of water sublimation. Molecular emissions were only detected in the spectra of comet 29P/Schwassmann-Wachmann 1. The linear polarization of distant comets with a high level of activity is the first ever measured at the heliocentric distances larger than 5 AU. The degree of linear polarization (from -2 to -3.7%) for these comets is significantly higher (in absolute value) than the typical value of the whole coma polarization (about -1.5 %) at the minimum of negative polarization branch for close to the Sun comets.

  18. Continuous synthesis process of hexagonal nanoplates of P6m ordered mesoporous silica.

    PubMed

    Jammaer, Jasper; van Erp, Titus S; Aerts, Alexander; Kirschhock, Christine E A; Martens, Johan A

    2011-08-31

    Hexagonally ordered mesoporous silica coined COK-12 was synthesized in a continuous process by combining streams of sodium silicate and citric acid/sodium citrate buffered solution of (ethylene oxide)(20)-(propylene oxide)(70)-(ethylene oxide)(20) triblock copolymer (Pluronic P123) from separate reservoirs. COK-12 precipitated spontaneously upon combining both streams at nearly neutral pH and ambient temperature. Stable intermediates of the COK-12 formation process could be prepared by limiting sodium silicate addition. Investigation of these intermediates using small-angle X-ray scattering revealed COK-12 formed via an assembly process departing from spherical uncharged core-shell P123-silica micelles. The sterical stabilization of these micelles decreased upon accumulation of silicate oligomers in their shell. Aggregation of the spherical micelles led to cylindrical micelles, which aligned and adopted the final hexagonal organization. This unprecedentedly fast formation of P6m ordered mesoporous silica was caused by two factors in the synthesis medium: the neutral pH favoring uncharged silicate oligomers and the high salt concentration promoting hydrophobic interactions with surfactant micelles leading to silica accumulation in the PEO shell. The easy continuous synthesis process is convenient for large-scale production. The platelet particle morphology with short and identical internal channels will be advantageous for many applications such as pore replication, nanotube or fiber growth, catalytic functionalization, drug delivery, film and sensor development, and in nano dyes as well as for investigation of pore diffusion phenomena. PMID:21790195

  19. ARS-Media – A new public domain software package for the calculation of media recipes based on ion-specific constraints.

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Understanding the ion-specific effects of the mineral elements is a central theme of biology because these ions are fundamental to the composition and maintenance of life. However, experiments concerned with determining ionspecific effects are generally performed with salt, as opposed to ion, manip...

  20. Results of magnetic field measurements of CP-stars performed with the 6-m telescope. III. Observations in 2009

    NASA Astrophysics Data System (ADS)

    Romanyuk, I. I.; Semenko, E. A.; Kudryavtsev, D. O.; Moiseevaa, A. V.

    2016-07-01

    We present the results of measuring longitudinal magnetic fields ( B e ), rotation velocities ( v e sin i), and radial velocities ( V r ) of 44 stars observed with the Main Stellar Spectrograph (MSS) of the 6-m BTA telescope of the Special Astrophysical Observatory in 2009. For the first time, magnetic fields were detected for the stars HD5441, HD199180, HD225627, and BD+00° 4535. We show that for the same stars, the longitudinal fields B e measured from the H β hydrogen line core and from metal lines can differ by 10% and up to a factor of 2-3. Except in rare cases, magnetic fields measured from the metal lines are stronger. We believe that this phenomenon is of a physical nature and depends on the magnetic field topology and the physical conditions inside a specific star. Observations of standard stars without magnetic fields confirm the absence of systematic errors capable of introducing distortions into the longitudinal-field measurement results. In this work we comment on the results for each of the stars.

  1. Prevention policies addressing packaging and packaging waste: Some emerging trends.

    PubMed

    Tencati, Antonio; Pogutz, Stefano; Moda, Beatrice; Brambilla, Matteo; Cacia, Claudia

    2016-10-01

    Packaging waste is a major issue in several countries. Representing in industrialized countries around 30-35% of municipal solid waste yearly generated, this waste stream has steadily grown over the years even if, especially in Europe, specific recycling and recovery targets have been fixed. Therefore, an increasing attention starts to be devoted to prevention measures and interventions. Filling a gap in the current literature, this explorative paper is a first attempt to map the increasingly important phenomenon of prevention policies in the packaging sector. Through a theoretical sampling, 11 countries/states (7 in and 4 outside Europe) have been selected and analyzed by gathering and studying primary and secondary data. Results show evidence of three specific trends in packaging waste prevention policies: fostering the adoption of measures directed at improving packaging design and production through an extensive use of the life cycle assessment; raising the awareness of final consumers by increasing the accountability of firms; promoting collaborative efforts along the packaging supply chains. PMID:27372152

  2. Packaging for logistical support

    NASA Astrophysics Data System (ADS)

    Twede, Diana; Hughes, Harold

    Logistical packaging is conducted to furnish protection, utility, and communication for elements of a logistical system. Once the functional requirements of space logistical support packaging have been identified, decision-makers have a reasonable basis on which to compare package alternatives. Flexible packages may be found, for example, to provide adequate protection and superior utility to that of rigid packages requiring greater storage and postuse waste volumes.

  3. Challenges in the Packaging of MEMS

    SciTech Connect

    Malshe, A.P.; Singh, S.B.; Eaton, W.P.; O'Neal, C.; Brown, W.D.; Miller, W.M.

    1999-03-26

    The packaging of Micro-Electro-Mechanical Systems (MEMS) is a field of great importance to anyone using or manufacturing sensors, consumer products, or military applications. Currently much work has been done in the design and fabrication of MEMS devices but insufficient research and few publications have been completed on the packaging of these devices. This is despite the fact that packaging is a very large percentage of the total cost of MEMS devices. The main difference between IC packaging and MEMS packaging is that MEMS packaging is almost always application specific and greatly affected by its environment and packaging techniques such as die handling, die attach processes, and lid sealing. Many of these aspects are directly related to the materials used in the packaging processes. MEMS devices that are functional in wafer form can be rendered inoperable after packaging. MEMS dies must be handled only from the chip sides so features on the top surface are not damaged. This eliminates most current die pick-and-place fixtures. Die attach materials are key to MEMS packaging. Using hard die attach solders can create high stresses in the MEMS devices, which can affect their operation greatly. Low-stress epoxies can be high-outgassing, which can also affect device performance. Also, a low modulus die attach can allow the die to move during ultrasonic wirebonding resulting to low wirebond strength. Another source of residual stress is the lid sealing process. Most MEMS based sensors and devices require a hermetically sealed package. This can be done by parallel seam welding the package lid, but at the cost of further induced stress on the die. Another issue of MEMS packaging is the media compatibility of the packaged device. MEMS unlike ICS often interface with their environment, which could be high pressure or corrosive. The main conclusion we can draw about MEMS packaging is that the package affects the performance and reliability of the MEMS devices. There is a

  4. Natural biopolimers in organic food packaging

    NASA Astrophysics Data System (ADS)

    Wieczynska, Justyna; Cavoski, Ivana; Chami, Ziad Al; Mondelli, Donato; Di Donato, Paola; Di Terlizzi, Biagio

    2014-05-01

    Concerns on environmental and waste problems caused by use of non-biodegradable and non-renewable based plastic packaging have caused an increase interest in developing biodegradable packaging using renewable natural biopolymers. Recently, different types of biopolymers like starch, cellulose, chitosan, casein, whey protein, collagen, egg white, soybean protein, corn zein, gelatin and wheat gluten have attracted considerable attention as potential food packaging materials. Recyclable or biodegradable packaging material in organic processing standards is preferable where possible but specific principles of packaging are not precisely defined and standards have to be assessed. There is evidence that consumers of organic products have specific expectations not only with respect to quality characteristics of processed food but also in social and environmental aspects of food production. Growing consumer sophistication is leading to a proliferation in food eco-label like carbon footprint. Biopolymers based packaging for organic products can help to create a green industry. Moreover, biopolymers can be appropriate materials for the development of an active surfaces designed to deliver incorporated natural antimicrobials into environment surrounding packaged food. Active packaging is an innovative mode of packaging in which the product and the environment interact to prolong shelf life or enhance safety or sensory properties, while maintaining the quality of the product. The work will discuss the various techniques that have been used for development of an active antimicrobial biodegradable packaging materials focusing on a recent findings in research studies. With the current focus on exploring a new generation of biopolymer-based food packaging materials with possible applications in organic food packaging. Keywords: organic food, active packaging, biopolymers , green technology

  5. Scientific instrumentation for the 1.6 m New Solar Telescope in Big Bear

    NASA Astrophysics Data System (ADS)

    Cao, W.; Gorceix, N.; Coulter, R.; Ahn, K.; Rimmele, T. R.; Goode, P. R.

    2010-06-01

    The NST (New Solar Telescope), a 1.6 m clear aperture, off-axis telescope, is in its commissioning phase at Big Bear Solar Observatory (BBSO). It will be the most capable, largest aperture solar telescope in the US until the 4 m ATST (Advanced Technology Solar Telescope) comes on-line late in the next decade. The NST will be outfitted with state-of-the-art scientific instruments at the Nasmyth focus on the telescope floor and in the Coudé Lab beneath the telescope. At the Nasmyth focus, several filtergraphs already in routine operation have offered high spatial resolution photometry in TiO 706 nm, H\\alpha 656 nm, G-band 430 nm and the near infrared (NIR), with the aid of a correlation tracker and image reconstruction system. Also, a Cryogenic Infrared Spectrograph (CYRA) is being developed to supply high signal-to-noise-ratio spectrometry and polarimetry spanning 1.0 to 5.0 μm. The Coudé Lab instrumentation will include Adaptive Optics (AO), InfraRed Imaging Magnetograph (IRIM), Visible Imaging Magnetograph (VIM), and Fast Imaging Solar Spectrograph (FISS). A 308 sub-aperture (349-actuator deformable mirror) AO system will enable nearly diffraction limited observations over the NST's principal operating wavelengths from 0.4 μm through 1.7 μm. IRIM and VIM are Fabry-Pérot based narrow-band tunable filters, which provide high resolution two-dimensional spectroscopic and polarimetric imaging in the NIR and visible respectively. FISS is a collaboration between BBSO and Seoul National University focussing on chromosphere dynamics. This paper reports the up-to-date progress on these instruments including an overview of each instrument and details of the current state of design, integration, calibration and setup/testing on the NST.

  6. 1.6 m Off-Axis Solar Telescope at Big Bear Solar Observatory

    NASA Astrophysics Data System (ADS)

    Goode, P. R.; BBSO/NJIT Team; Mees Solar Obs./U. Hawaii Team

    2003-05-01

    New Jersey Institute of Technology (NJIT), in collaboration with the University of Hawaii (UH), is upgrading Big Bear Solar Observatory (BBSO) by replacing its principal, 65 cm aperture telescope with a modern, off-axis 1.6 m clear aperture instrument from a 1.7 m blank. The new telescope offers a significant incremental improvement in ground-based infrared and high angular resolution capabilities, and enhances our continuing program to understand photospheric magneto-convection and chromospheric dynamics. These are the drivers for what is broadly called space weather -- an important problem, which impacts human technologies and life on earth. This New Solar Telescope (NST) will use the existing BBSO pedestal, pier and observatory building, which will be modified to accept the larger open telescope structure. It will be operated together with our 10 inch (for larger field-of-view vector magnetograms, Ca II K and Hα observations) and Singer-Link (full disk Hα , Ca II K and white light) synoptic telescopes. The NST optical and software control design will be similar to the existing SOLARC (UH) and the planned Advanced Technology Solar Telescope (ATST) facility led by the National Solar Observatory (NSO) -- all three are off-axis designs. The highest resolution solar telescopes currently operating are in the sub-meter class, and have diffraction limits which allow them to resolve features larger than 100 km in size on the sun. They are often photon-starved in the study of dynamic events because of the competing need for diffraction limited spatial resolution, short exposure times to minimize seeing effects, and high spectral resolution to resolve line profiles. Thus, understanding many significant and dynamic solar phenomena remains tantalizingly close, but just beyond our grasp. Research supported in part by NASA grant NAG5-12782 and NSF grant ATM-0086999.

  7. 1.6 M Solar Telescope in Big Bear -- The NST

    NASA Astrophysics Data System (ADS)

    Goode, Philip R.; Denker, Carsten J.; Didkovsky, Leonid I.; Kuhn, J. R.; Wang, Haimin

    2003-06-01

    New Jersey Institute of Technology (NJIT), in collaboration with the University of Hawaii (UH), is upgrading Big Bear Solar Observatory (BBSO) by replacing its principal, 65 cm aperture telescope with a modern, off-axis 1.6 m clear aperture instrument from a 1.7 m blank. The new telescope offers a significant incremental improvement in ground-based infrared and high angular resolution capabilities, and enhances our continuing program to understand photospheric magneto-convection and chromospheric dynamics. These are the drivers for what is broadly called space weather -- an important problem, which impacts human technologies and life on earth. This New Solar Telescope (NST) will use the existing BBSO pedestal, pier and observatory building, which will be modified to accept the larger open telescope structure. It will be operated together with our 10 inch (for larger field-of-view vector magnetograms, Ca II K and Hα observations) and Singer-Link (full disk Hα, Ca II K and white light) synoptic telescopes. The NST optical and software control design will be similar to the existing SOLARC (UH) and the planned Advanced Technology Solar Telescope (ATST) facility led by the National Solar Observatory (NSO) -- all three are off-axis designs. The NST will be available to guest observers and will continue BBSO's open data policy. The polishing of the primary will be done in partnership with the University of Arizona Mirror Lab, where their proof-of-concept for figuring 8 m pieces of 20 m nighttime telescopes will be the NST's primary mirror. We plan for the NST's first light in late 2005. This new telescope will be the largest aperture solar telescope, and the largest aperture off-axis telescope, located in one of the best observing sites. It will enable new, cutting edge science. The scientific results will be extremely important to space weather and global climate change research.

  8. Detection of an intergalactic meteor particle with the 6-m telescope

    NASA Astrophysics Data System (ADS)

    Afanasiev, V. L.; Kalenichenko, V. V.; Karachentsev, I. D.

    2007-12-01

    On July 28, 2006 the 6-m telescope of the Special Astrophysical Observatory of the Russian Academy of Sciences recorded the spectrum of a faint meteor. We confidently identify the lines of FeI and MgI, OI, NI and molecular-nitrogen (N2) bands. The entry velocity of the meteor body into the Earth’s atmosphere estimated from radial velocity is equal to 300 km/s. The body was several tens of a millimeter in size, like chondrules in carbon chondrites. The radiant of the meteor trajectory coincides with the sky position of the apex of the motion of the Solar system toward the centroid of the Local Group of galaxies. Observations of faint sporadic meteors with FAVOR TV CCD camera confirmed the radiant at a higher than 96% confidence level. We conclude that this meteor particle is likely to be of extragalactic origin. The following important questions remain open: (1) How metal-rich dust particles came to be in the extragalactic space? (2) Why are the sizes of extragalactic particles larger by two orders of magnitude (and their masses greater by six orders of magnitude) than common interstellar dust grains in our Galaxy? (3) If extragalactic dust surrounds galaxies in the form of dust (or gas-and-dust) aureoles, can such formations now be observed using other observational techniques (IR observations aboard Spitzer satellite, etc.)? (4) If inhomogeneous extragalactic dust medium with the parameters mentioned above actually exists, does it show up in the form of irregularities on the cosmic microwave background (WMAP etc.)?

  9. 76 FR 23749 - Intelligent Mail Package Barcode (IMpb) Implementation for Commercial Parcels

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-28

    ... 111 Intelligent Mail Package Barcode (IMpb) Implementation for Commercial Parcels AGENCY: Postal... currently enhancing its operational capability to allow for the scanning of Intelligent Mail package..., payment, and reporting. Intelligent Mail package barcodes also include specific ``mail class...

  10. Antimicrobial food packaging in meat industry.

    PubMed

    Quintavalla, Stefania; Vicini, Loredana

    2002-11-01

    Antimicrobial packaging, an active packaging concept, can be considered an extremely challenging technology that could have a significant impact on shelf-life extension and food safety of meat and meat products. Use of antimicrobial substances can control the microbial population and target specific microorganisms to provide higher safety and quality products. Many classes of antimicrobial compounds have been evaluated in film structures, both synthetic polymers and edible films: organic acids and their salts, enzymes, bacteriocins, and miscellaneous compounds such as triclosan, silver zeolites, and fungicides. The characteristics of some antimicrobial packaging systems are reviewed in this article. The regulatory status of antimicrobial packaging in EU is also examined. PMID:22061613

  11. Challenges in the Packaging of MEMS

    SciTech Connect

    BROWN, WILLIAM D.; EATON, WILLIAM P.; MALSHE, AJAY P.; MILLER, WILLIAM M.; O'NEAL, CHAD; SINGH, SUSHILA B.

    1999-09-24

    Microelectromechanical Systems (MEMS) packaging is much different from conventional integrated circuit (IC) packaging. Many MEMS devices must interface to the environment in order to perform their intended function, and the package must be able to facilitate access with the environment while protecting the device. The package must also not interfere with or impede the operation of the MEMS device. The die attachment material should be low stress, and low outgassing, while also minimizing stress relaxation overtime which can lead to scale factor shifts in sensor devices. The fabrication processes used in creating the devices must be compatible with each other, and not result in damage to the devices. Many devices are application specific requiring custom packages that are not commercially available. Devices may also need media compatible packages that can protect the devices from harsh environments in which the MEMS device may operate. Techniques are being developed to handle, process, and package the devices such that high yields of functional packaged parts will result. Currently, many of the processing steps are potentially harmful to MEMS devices and negatively affect yield. It is the objective of this paper to review and discuss packaging challenges that exist for MEMS systems and to expose these issues to new audiences from the integrated circuit packaging community.

  12. Packaging for Food Service

    NASA Technical Reports Server (NTRS)

    Stilwell, E. J.

    1985-01-01

    Most of the key areas of concern in packaging the three principle food forms for the space station were covered. It can be generally concluded that there are no significant voids in packaging materials availability or in current packaging technology. However, it must also be concluded that the process by which packaging decisions are made for the space station feeding program will be very synergistic. Packaging selection will depend heavily on the preparation mechanics, the preferred presentation and the achievable disposal systems. It will be important that packaging be considered as an integral part of each decision as these systems are developed.

  13. Waste Package Lifting Calculation

    SciTech Connect

    H. Marr

    2000-05-11

    The objective of this calculation is to evaluate the structural response of the waste package during the horizontal and vertical lifting operations in order to support the waste package lifting feature design. The scope of this calculation includes the evaluation of the 21 PWR UCF (pressurized water reactor uncanistered fuel) waste package, naval waste package, 5 DHLW/DOE SNF (defense high-level waste/Department of Energy spent nuclear fuel)--short waste package, and 44 BWR (boiling water reactor) UCF waste package. Procedure AP-3.12Q, Revision 0, ICN 0, calculations, is used to develop and document this calculation.

  14. Lessons learned during Type A Packaging testing

    SciTech Connect

    O`Brien, J.H.; Kelly, D.L.

    1995-11-01

    For the past 6 years, the US Department of Energy (DOE) Office of Facility Safety Analysis (EH-32) has contracted Westinghouse Hanford Company (WHC) to conduct compliance testing on DOE Type A packagings. The packagings are tested for compliance with the U.S. Department of Transportation (DOT) Specification 7A, general packaging, Type A requirements. The DOE has shared the Type A packaging information throughout the nuclear materials transportation community. During testing, there have been recurring areas of packaging design that resulted in testing delays and/or initial failure. The lessons learned during the testing are considered a valuable resource. DOE requested that WHC share this resource. By sharing what is and can be encountered during packaging testing, individuals will hopefully avoid past mistakes.

  15. Scientific Instruments of 1.6 m New Solar Telescope in Big Bear

    NASA Astrophysics Data System (ADS)

    Cao, W.

    2009-12-01

    The NST (New Solar Telescope) is in its commissioning phase at Big Bear Solar Observatory (BBSO). It will be the most capable, largest aperture solar telescope in the US until the 4 m ATST (Advanced Technology Solar Telescope) comes on-line in the middle of the next decade. The NST will be outfitted with state-of-the-art post-focus instrumentations at the Nasmyth focus on the dome floor and in the Coude Lab beneath the telescope. At the Nasmyth focus, several filter-based systems already in routine operation offer high spatial resolution photometry in TiO 704 nm, Hα 656 nm, G-band 430 nm and near infrared 1.56 μm & 2.2 μm, with the assistance of local correlation tracking and image reconstruction. As well, a Cryogenic InfraRed Spectrograph (CIRS) is being developed to supply high signal-to-noise-ratio spectrometry and polarimetry spanning 1.0 to 5.0 μm. The Coudé-lab instrumentations will include Adaptive Optics system (AO), InfraRed Imaging Magnetograph (IRIM), Visible Imaging Magnetograph (VIM), Real-time Image Reconstruction System (RIRS), and Fast Imaging Solar Spectrograph (FISS) -- most of these instruments operated on the old 0.6 m BBSO telescope. AO is being upgraded to a 308 sub-aperture (349-actuator Deformable Mirror) AO system that will enable diffraction limited observations over the NST's principal operating wavelengths from 0.4 through 1.7 μm. IRIM and VIM are Fabry-Pérot based narrow-band tunable filter, which provide high resolution two-dimensional spectroscopic and polarimetric imaging in the near infrared and visible respectively. Using a 32-node parallel computing system, RIRS is capable of performing real-time image reconstruction with one image every minute. FISS is a collaboration between BBSO and Seoul National University to focus on chromosphere dynamics. Key tasks including optical design, hardware/software integration and subsequent setup/testing on the NST, will be presented here. Some preliminary observation results in the near

  16. Packaging - Materials review

    NASA Astrophysics Data System (ADS)

    Herrmann, Matthias

    2014-06-01

    Nowadays, a large number of different electrochemical energy storage systems are known. In the last two decades the development was strongly driven by a continuously growing market of portable electronic devices (e.g. cellular phones, lap top computers, camcorders, cameras, tools). Current intensive efforts are under way to develop systems for automotive industry within the framework of electrically propelled mobility (e.g. hybrid electric vehicles, plug-in hybrid electric vehicles, full electric vehicles) and also for the energy storage market (e.g. electrical grid stability, renewable energies). Besides the different systems (cell chemistries), electrochemical cells and batteries were developed and are offered in many shapes, sizes and designs, in order to meet performance and design requirements of the widespread applications. Proper packaging is thereby one important technological step for designing optimum, reliable and safe batteries for operation. In this contribution, current packaging approaches of cells and batteries together with the corresponding materials are discussed. The focus is laid on rechargeable systems for industrial applications (i.e. alkaline systems, lithium-ion, lead-acid). In principle, four different cell types (shapes) can be identified - button, cylindrical, prismatic and pouch. Cell size can be either in accordance with international (e.g. International Electrotechnical Commission, IEC) or other standards or can meet application-specific dimensions. Since cell housing or container, terminals and, if necessary, safety installations as inactive (non-reactive) materials reduce energy density of the battery, the development of low-weight packages is a challenging task. In addition to that, other requirements have to be fulfilled: mechanical stability and durability, sealing (e.g. high permeation barrier against humidity for lithium-ion technology), high packing efficiency, possible installation of safety devices (current interrupt device

  17. Packaging - Materials review

    SciTech Connect

    Herrmann, Matthias

    2014-06-16

    Nowadays, a large number of different electrochemical energy storage systems are known. In the last two decades the development was strongly driven by a continuously growing market of portable electronic devices (e.g. cellular phones, lap top computers, camcorders, cameras, tools). Current intensive efforts are under way to develop systems for automotive industry within the framework of electrically propelled mobility (e.g. hybrid electric vehicles, plug-in hybrid electric vehicles, full electric vehicles) and also for the energy storage market (e.g. electrical grid stability, renewable energies). Besides the different systems (cell chemistries), electrochemical cells and batteries were developed and are offered in many shapes, sizes and designs, in order to meet performance and design requirements of the widespread applications. Proper packaging is thereby one important technological step for designing optimum, reliable and safe batteries for operation. In this contribution, current packaging approaches of cells and batteries together with the corresponding materials are discussed. The focus is laid on rechargeable systems for industrial applications (i.e. alkaline systems, lithium-ion, lead-acid). In principle, four different cell types (shapes) can be identified - button, cylindrical, prismatic and pouch. Cell size can be either in accordance with international (e.g. International Electrotechnical Commission, IEC) or other standards or can meet application-specific dimensions. Since cell housing or container, terminals and, if necessary, safety installations as inactive (non-reactive) materials reduce energy density of the battery, the development of low-weight packages is a challenging task. In addition to that, other requirements have to be fulfilled: mechanical stability and durability, sealing (e.g. high permeation barrier against humidity for lithium-ion technology), high packing efficiency, possible installation of safety devices (current interrupt device

  18. SAM -- A Spectral Extraction Package

    NASA Astrophysics Data System (ADS)

    Lewis, J. R.

    In this note a description is given of SAM, a package written at RGO for the extraction of spectra from two dimensional data frames. The need to extract spectra from two dimensional frames in an optimal manner (e.g. one in which the signal to noise ratio was maximised) was the primary reason for the writing of the package. The programs were originally written with FOS, ISIS and IDS in mind, but contain nothing which is instrument specific and hence should be applicable to any two dimensional spectral data frame.

  19. CH Packaging Operations Manual

    SciTech Connect

    Washington TRU Solutions LLC

    2005-06-13

    This procedure provides instructions for assembling the CH Packaging Drum payload assembly, Standard Waste Box (SWB) assembly, Abnormal Operations and ICV and OCV Preshipment Leakage Rate Tests on the packaging seals, using a nondestructive Helium (He) Leak Test.

  20. Comparative Packaging Study

    NASA Technical Reports Server (NTRS)

    Perchonok, Michele; Antonini, David

    2008-01-01

    This viewgraph presentation describes a comparative packaging study for use on long duration space missions. The topics include: 1) Purpose; 2) Deliverables; 3) Food Sample Selection; 4) Experimental Design Matrix; 5) Permeation Rate Comparison; and 6) Packaging Material Information.

  1. KMTNET: A Network of 1.6 m Wide-Field Optical Telescopes Installed at Three Southern Observatories

    NASA Astrophysics Data System (ADS)

    Kim, Seung-Lee; Lee, Chung-Uk; Park, Byeong-Gon; Kim, Dong-Jin; Cha, Sang-Mok; Lee, Yongseok; Han, Cheongho; Chun, Moo-Young; Yuk, Insoo

    2016-02-01

    The Korea Microlensing Telescope Network (KMTNet) is a wide-field photometric system installed by the Korea Astronomy and Space Science Institute (KASI). Here, we present the overall technical specifications of the KMTNet observation system, test observation results, data transfer and image processing procedure, and finally, the KMTNet science programs. The system consists of three 1.6 m wide-field optical telescopes equipped with mosaic CCD cameras of 18k by 18k pixels. Each telescope provides a 2.0 by 2.0 square degree field of view. We have finished installing all three telescopes and cameras sequentially at the Cerro-Tololo Inter-American Observatory (CTIO) in Chile, the South African Astronomical Observatory (SAAO) in South Africa, and the Siding Spring Observatory (SSO) in Australia. This network of telescopes, which is spread over three different continents at a similar latitude of about -30 degrees, enables 24-hour continuous monitoring of targets observable in the Southern Hemisphere. The test observations showed good image quality that meets the seeing requirement of less than 1.0 arcsec in I-band. All of the observation data are transferred to the KMTNet data center at KASI via the international network communication and are processed with the KMTNet data pipeline. The primary scientific goal of the KMTNet is to discover numerous extrasolar planets toward the Galactic bulge by using the gravitational microlensing technique, especially earth-mass planets in the habitable zone. During the non-bulge season, the system is used for wide-field photometric survey science on supernovae, asteroids, and external galaxies.

  2. ATLAS software packaging

    NASA Astrophysics Data System (ADS)

    Rybkin, Grigory

    2012-12-01

    Software packaging is indispensable part of build and prerequisite for deployment processes. Full ATLAS software stack consists of TDAQ, HLT, and Offline software. These software groups depend on some 80 external software packages. We present tools, package PackDist, developed and used to package all this software except for TDAQ project. PackDist is based on and driven by CMT, ATLAS software configuration and build tool, and consists of shell and Python scripts. The packaging unit used is CMT project. Each CMT project is packaged as several packages—platform dependent (one per platform available), source code excluding header files, other platform independent files, documentation, and debug information packages (the last two being built optionally). Packaging can be done recursively to package all the dependencies. The whole set of packages for one software release, distribution kit, also includes configuration packages and contains some 120 packages for one platform. Also packaged are physics analysis projects (currently 6) used by particular physics groups on top of the full release. The tools provide an installation test for the full distribution kit. Packaging is done in two formats for use with the Pacman and RPM package managers. The tools are functional on the platforms supported by ATLAS—GNU/Linux and Mac OS X. The packaged software is used for software deployment on all ATLAS computing resources from the detector and trigger computing farms, collaboration laboratories computing centres, grid sites, to physicist laptops, and CERN VMFS and covers the use cases of running all applications as well as of software development.

  3. Modular avionics packaging standardization

    NASA Astrophysics Data System (ADS)

    Austin, M.; McNichols, J. K.

    The Modular Avionics Packaging (MAP) Program for packaging future military avionics systems with the objective of improving reliability, maintainability, and supportability, and reducing equipment life cycle costs is addressed. The basic MAP packaging concepts called the Standard Avionics Module, the Standard Enclosure, and the Integrated Rack are summarized, and the benefits of modular avionics packaging, including low risk design, technology independence with common functions, improved maintainability and life cycle costs are discussed. Progress made in MAP is briefly reviewed.

  4. CCD polarimetry of distant comets with the 6-m telescope at SAO RAN

    NASA Astrophysics Data System (ADS)

    Ivanova, A.; Dlugach, J.; Afanasiev, V.; Reshetnyk, V.; Korsun, P.

    2014-07-01

    Usually, polarimetric measurements are used to study the physical properties of comets approaching the Sun. Since the dust in distant comets differs from the dust in short-period comets, the study of polarization of the distant comets is very important for the investigation of their physical properties. However, little is known about the dust properties in the cometary coma as well as about the cometary nuclei at large heliocentric distances. So far, there are no comets studied with polarimetric techniques at heliocentric distances more than 4 au. We have started a comprehensive program of polarimetric, photometric, and spectral investigations of active distant comets (or without noticeable activity) with the focal reducer SCORPIO attached in the prime focus of the 6-m telescope BTA (Special Astrophysical Observatory, Russia). We performed broad-band polarimetry and long-slit spectroscopy of comets C/2011 S1 (LINEAR) and C/2010 R1 (LINEAR) in the visible wavelength range. The data were obtained on November 12, 2012, at the phase angle of 10.4°, when the comet C/2011 S1 (LINEAR) was at the heliocentric distance of 6 au, and, on February 6, 2013, at the phase angle of 9.1°, when the comet C/2010 R1 (LINEAR) was at the heliocentric distance of 5.9 au, respectively. The data on the degree of linear polarization of the distant comets C/2011 S1 (LINEAR) and C/2010 R1 (LINEAR) are the first ever obtained at such large heliocentric distances. We present the results and preliminary analysis of imaging polarimetric observations of comets C/2011 S1 (LINEAR) and C/2010 R1 (LINEAR). These comets show considerable levels of activity not only within the zone of water sublimation (up to 3 au), but also at heliocentric distances far exceeding this limit. Molecular emissions are not detected in the observed cometary spectra. The cometary comae display a degree of linear polarization of about -2% and -2.2%, respectively. This value is significantly higher, in absolute terms, than

  5. Trends in Food Packaging.

    ERIC Educational Resources Information Center

    Ott, Dana B.

    1988-01-01

    This article discusses developments in food packaging, processing, and preservation techniques in terms of packaging materials, technologies, consumer benefits, and current and potential food product applications. Covers implications due to consumer life-style changes, cost-effectiveness of packaging materials, and the ecological impact of…

  6. Binary star speckle measurements during 1992-1997 from the SAO 6-m and 1-m telescopes in Zelenchuk

    NASA Astrophysics Data System (ADS)

    Balega, I. I.; Balega, Y. Y.; Maksimov, A. F.; Pluzhnik, E. A.; Shkhagosheva, Z. U.; Vasyuk, V. A.

    1999-12-01

    We present the results of speckle interferometric measurements of binary stars made with the television photon-counting camera at the 6-m Big Azimuthal Telescope (BTA) and 1-m telescope of the Special Astrophysical Observatory (SAO) between August 1992 and May 1997. The data contain 89 observations of 62 star systems on the large telescope and 21 on the smaller one. For the 6-m aperture 18 systems remained unresolved. The measured angular separation ranged from 39 mas, two times above the BTA diffraction limit, to 1593 mas.

  7. Balloon gondola diagnostics package

    NASA Technical Reports Server (NTRS)

    Cantor, K. M.

    1986-01-01

    In order to define a new gondola structural specification and to quantify the balloon termination environment, NASA developed a balloon gondola diagnostics package (GDP). This addition to the balloon flight train is comprised of a large array of electronic sensors employed to define the forces and accelerations imposed on a gondola during the termination event. These sensors include the following: a load cell, a three-axis accelerometer, two three-axis rate gyros, two magnetometers, and a two axis inclinometer. A transceiver couple allows the data to be telemetered across any in-line rotator to the gondola-mounted memory system. The GDP is commanded 'ON' just prior to parachute deployment in order to record the entire event.

  8. 49 CFR 173.415 - Authorized Type A packages.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... evaluation or comparative data showing that the construction methods, packaging design, and materials of... standards for fissile materials in 10 CFR part 71 and is used in accordance with § 173.471. (c) Any Type B(U... packaging. Each offeror of a Specification 7A package must maintain on file for at least one year after...

  9. 49 CFR 178.910 - Marking of Large Packagings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Marking of Large Packagings. 178.910 Section 178.910 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR PACKAGINGS Large Packagings Standards § 178.910 Marking...

  10. 49 CFR 178.910 - Marking of Large Packagings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR PACKAGINGS... packaging symbol as illustrated in § 178.503(e)(1)(i). For metal Large Packagings on which the marking is stamped or embossed, the capital letters “UN” may be applied instead of the symbol; (ii) The code...

  11. 49 CFR 178.910 - Marking of Large Packagings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR PACKAGINGS... in § 178.503(e)(1)(ii), the United Nations packaging symbol as illustrated in § 178.503(e)(1)(i). For... applied instead of the symbol; (ii) The code number designating the Large Packaging design type...

  12. Health Instruction Packages: Specific Nursing Skills.

    ERIC Educational Resources Information Center

    Bates, Clarice; And Others

    Text, illustrations, and exercises are utilized in a set of five learning modules designed to instruct nursing students in a variety of clinical skills. The first module, "Down the Tube: Insertion of a Nasogastric Tube" by Clarice Bates, describes materials and procedures used to insert a nasogastric tube through the nose and esophagus and into…

  13. Development of the fully digital dc speed regulation system in 8-mX6-m wind tunnel

    NASA Astrophysics Data System (ADS)

    Li, Dexiang; Ye, Jicheng; You, Xi; Zhang, Xiande

    2000-05-01

    The old analog system of speed regulation of 8 m X 6 m wind tunnel has been successfully reformed recently. The new system realized fully digital control on 2600 kW DC motor, through rebuilding two sets of 485 V and 30 A speed regulation equipment used in controlling large power thyristor rectifier of 2-stage serial.

  14. Proton beam of 2 MeV 1.6 mA on a tandem accelerator with vacuum insulation

    NASA Astrophysics Data System (ADS)

    Kasatov, D.; Kuznetsov, A.; Makarov, A.; Shchudlo, I.; Sorokin, I.; Taskaev, S.

    2014-12-01

    A source of epithermal neutrons based on a tandem accelerator with vacuum insulation for boron neutron capture therapy of malignant tumors was proposed and constructed. Stationary proton beam with 2 MeV energy, 1.6 mA current, 0.1% energy monochromaticity and 0.5% current stability has just been obtained.

  15. 49 CFR 173.24a - Additional general requirements for non-bulk packagings and packages.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ...) Refrigerants, such as dry ice or liquid nitrogen, as authorized under the HMR; (ii) Anticoagulants used to... packaging containing liquid hazardous materials must be packed so that closures on inner packagings are... with a liquid hazardous material only when the specific gravity of the material does not exceed...

  16. 49 CFR 173.24a - Additional general requirements for non-bulk packagings and packages.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ...) Refrigerants, such as dry ice or liquid nitrogen, as authorized under the HMR; (ii) Anticoagulants used to... packaging containing liquid hazardous materials must be packed so that closures on inner packagings are... with a liquid hazardous material only when the specific gravity of the material does not exceed...

  17. 49 CFR 173.24a - Additional general requirements for non-bulk packagings and packages.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ...) Refrigerants, such as dry ice or liquid nitrogen, as authorized under the HMR; (ii) Anticoagulants used to... packaging containing liquid hazardous materials must be packed so that closures on inner packagings are... with a liquid hazardous material only when the specific gravity of the material does not exceed...

  18. 49 CFR 173.24a - Additional general requirements for non-bulk packagings and packages.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ...) Refrigerants, such as dry ice or liquid nitrogen, as authorized under the HMR; (ii) Anticoagulants used to... packaging containing liquid hazardous materials must be packed so that closures on inner packagings are... with a liquid hazardous material only when the specific gravity of the material does not exceed...

  19. Thermal analysis of the 10-gallon and the 55-gallon DOT-6M containers with thermal boundary conditions corresponding to 10CFR71 normal transport and accident conditions

    SciTech Connect

    Sanchez, L.C.; Longenbaugh, R.S.; Moss, M.; Haseman, G.M.; Fowler, W.E.; Roth, E.P.

    1988-03-01

    This report describes the heat transfer analysis of the 10-gallon and 55-gallon 6M containers. The analysis was performed with boundary conditions corresponding to a normal transport condition and a hypothetical accident condition. Computational results indicated that the insulation material in the 6M containers will adequately protect the payload region of the 6M containers. 26 refs., 26 figs., 8 tabs.

  20. High density modular avionics packaging

    NASA Astrophysics Data System (ADS)

    Poradish, F.

    Requirements and design configurations for high density modular avionics packaging are examined, with particular attention given to new hardware trends, the design of high-density standard modules (HDSM's), and HDSM requirements. The discussion of the HDSM's covers thermal management, system testability, power supply, and performance specifications. The general design of an integrated HDSM demonstration system currently under construction is briefly described, and some test data are presented.

  1. Smart packaging for photonics

    SciTech Connect

    Smith, J.H.; Carson, R.F.; Sullivan, C.T.; McClellan, G.; Palmer, D.W.

    1997-09-01

    Unlike silicon microelectronics, photonics packaging has proven to be low yield and expensive. One approach to make photonics packaging practical for low cost applications is the use of {open_quotes}smart{close_quotes} packages. {open_quotes}Smart{close_quotes} in this context means the ability of the package to actuate a mechanical change based on either a measurement taken by the package itself or by an input signal based on an external measurement. One avenue of smart photonics packaging, the use of polysilicon micromechanical devices integrated with photonic waveguides, was investigated in this research (LDRD 3505.340). The integration of optical components with polysilicon surface micromechanical actuation mechanisms shows significant promise for signal switching, fiber alignment, and optical sensing applications. The optical and stress properties of the oxides and nitrides considered for optical waveguides and how they are integrated with micromechanical devices were investigated.

  2. Packaged die heater

    SciTech Connect

    Spielberger, Richard; Ohme, Bruce Walker; Jensen, Ronald J.

    2011-06-21

    A heater for heating packaged die for burn-in and heat testing is described. The heater may be a ceramic-type heater with a metal filament. The heater may be incorporated into the integrated circuit package as an additional ceramic layer of the package, or may be an external heater placed in contact with the package to heat the die. Many different types of integrated circuit packages may be accommodated. The method provides increased energy efficiency for heating the die while reducing temperature stresses on testing equipment. The method allows the use of multiple heaters to heat die to different temperatures. Faulty die may be heated to weaken die attach material to facilitate removal of the die. The heater filament or a separate temperature thermistor located in the package may be used to accurately measure die temperature.

  3. Stratimikos Wrapper Package

    2006-08-22

    Stratimikos is a small package of C++ wrappers for linear solver and preconditioning functionality exposed through Thyra interfaces. This package makes is possible to aggregate all of the general linear solver capability from the packages Amesos, AztecOO, Belos, lfpack, ML and others into a simple to use, parameter-list driven, interface to linear solvers. This initial version of Stratimikos contains just one utility class for building linear solvrs and preconditioners out of Epetra-based linear operators.

  4. Teaching Old Packaging New Tricks - 12593

    SciTech Connect

    England, Jeffery L.; Shuler, James M.

    2012-07-01

    Waste disposition campaigns have been an industry and government focus area since the mid- 1970's. With increased focus on this issue, and a lot of hard work, most waste packaging and transportation issues have been addressed. The material has been successfully shipped and dis-positioned. DOE has successfully de-inventoried materials from multiple sites to meet material consolidation, footprint reduction, nonproliferation, and regulatory obligations with cost savings from reduced maintenance and regulatory compliance. There has been a wide range of certified shipping packagings for the transportation of hazardous materials to meet most of the waste needs. The remaining materials are problematic, generally low volume, and do not meet the certified content of the existing inventory of packaging. Designing, testing and certifying new packaging designs can be a long and expensive process and for small volumes of material it is cost prohibitive. One very cost effective option is to lease and use a certified packaging to overpack waste containers. There are many robust certified packagings available with the capability to envelope the waste content. The capability to use inner containers, inside the current fleet of certified casks or packaging, to address specific content problems of additional shielding (e.g., U-233) or containment (e.g., sodium bonded nuclear material) has successfully expanded the capability for timely cost effective shipment of unique contents. This option has been used successfully in the NAC-LWT, T-3 and other packagings. (authors)

  5. Cigarette package design: opportunities for disease prevention

    PubMed Central

    DiFranza, JR; Clark, DM; Pollay, RW

    2003-01-01

    Objective To learn how cigarette packages are designed and to determine to what extent cigarette packages are designed to target children. Methods A computer search was made of all Internet websites that post tobacco industry documents using the search terms: packaging, package design, package study, box design, logo, trademark and design study. All documents were retrieved electronically and analyzed by the first author for recurrent themes. Data Synthesis Cigarette manufacturers devote a great deal of attention and expense to package design because it is central to their efforts to create brand images. Colors, graphic elements, proportioning, texture, materials and typography are tested and used in various combinations to create the desired product and user images. Designs help to create the perceived product attributes and project a personality image of the user with the intent of fulfilling the psychological needs of the targeted type of smoker. The communication of these images and attributes is conducted through conscious and subliminal processes. Extensive testing is conducted using a variety of qualitative and quantitative research techniques. Conclusion The promotion of tobacco products through appealing imagery cannot be stopped without regulating the package design. The same marketing research techniques used by the tobacco companies can be used to design generic packaging and more effective warning labels targeted at specific consumers. PMID:19570250

  6. Cigarette package design: opportunities for disease prevention

    PubMed Central

    DiFranza, JR; Clark, DM; Pollay, RW

    2003-01-01

    Objective To learn how cigarette packages are designed and to determine to what extent cigarette packages are designed to target children. Methods A computer search was made of all Internet websites that post tobacco industry documents using the search terms: packaging, package design, package study, box design, logo, trademark and design study. All documents were retrieved electronically and analyzed by the first author for recurrent themes. Data Synthesis Cigarette manufacturers devote a great deal of attention and expense to package design because it is central to their efforts to create brand images. Colors, graphic elements, proportioning, texture, materials and typography are tested and used in various combinations to create the desired product and user images. Designs help to create the perceived product attributes and project a personality image of the user with the intent of fulfilling the psychological needs of the targeted type of smoker. The communication of these images and attributes is conducted through conscious and subliminal processes. Extensive testing is conducted using a variety of qualitative and quantitative research techniques. Conclusion The promotion of tobacco products through appealing imagery cannot be stopped without regulating the package design. The same marketing research techniques used by the tobacco companies can be used to design generic packaging and more effective warning labels targeted at specific consumers.

  7. The ZOOM minimization package

    SciTech Connect

    Fischler, Mark S.; Sachs, D.; /Fermilab

    2004-11-01

    A new object-oriented Minimization package is available for distribution in the same manner as CLHEP. This package, designed for use in HEP applications, has all the capabilities of Minuit, but is a re-write from scratch, adhering to modern C++ design principles. A primary goal of this package is extensibility in several directions, so that its capabilities can be kept fresh with as little maintenance effort as possible. This package is distinguished by the priority that was assigned to C++ design issues, and the focus on producing an extensible system that will resist becoming obsolete.

  8. Requirements for food packaged in polymeric films.

    PubMed

    Rizvi, S S

    1981-01-01

    The requirements of barrier properties of packaging materials against environmental factors vary with food products. The chemical, physical, and biological mechanisms of food deterioration due to environmental factors, vital properties required in packaging materials, and developments in progress and future trends to maintain the required standard of food quality have been critically reviewed. Theoretical and experimental results for a variety of food products in relation to the properties of the packaging materials are discussed. Methods of prediction of food stability and their industrial applications are also emphasized by specific examples. PMID:7011684

  9. Flat conductor cable for electrical packaging

    NASA Technical Reports Server (NTRS)

    Angele, W.

    1972-01-01

    Flat conductor cable (FCC) is relatively new, highly promising means for electrical packaging and system integration. FCC offers numerous desirable traits (weight, volume and cost savings, flexibility, high reliability, predictable and repeatable electrical characteristics) which make it extremely attractive as a packaging medium. FCC, today, finds wide application in everything from integration of lunar equipment to the packaging of electronics in nuclear submarines. Described are cable construction and means of termination, applicable specifications and standards, and total FCC systems. A list of additional sources of data is also included for more intensive study.

  10. Decrease in transient receptor potential melastatin 6 mRNA stability caused by rapamycin in renal tubular epithelial cells.

    PubMed

    Ikari, Akira; Sanada, Ayumi; Sawada, Hayato; Okude, Chiaki; Tonegawa, Chie; Sugatani, Junko

    2011-06-01

    Rapamycin, an inhibitor of mammalian target of rapamycin (mTOR), is used in treatments for transplantation and cancer. Rapamycin causes hypomagnesemia, although precisely how has not been examined. Here, we investigated the effect of rapamycin on the expression of transient receptor potential melastatin 6 (TRPM6), a Mg2+ channel. Rapamycin and LY-294002, an inhibitor of phosphatidilinositol-3 kinase (PI3K) located upstream of mTOR, inhibited epidermal growth factor (EGF)-induced expression of the TRPM6 protein without affecting TRPM7 expression in rat renal NRK-52E epithelial cells. Both rapamycin and LY-294002 decreased EGF-induced Mg2+ influx. U0126, a MEK inhibitor, inhibited EGF-induced increases in c-Fos, p-ERK, and TRPM6 levels. In contrast, neither rapamycin nor LY-294002 inhibited EGF-induced increases in p-ERK and c-Fos levels. EGF increased p-Akt level, an effect inhibited by LY-294002 and 1L-6-hydroxymethyl-chiro-inositol2-[(R)-2-O-methyl-3-O-octadecylcarbonate] (Akt inhibitor). Akt inhibitor decreased TRPM6 level similar to rapamycin and LY-294002. These results suggest that a PI3K/Akt/mTOR pathway is involved in the regulation of TRPM6 expression. Rapamycin inhibited the EGF-induced increase in TRPM6 mRNA but did not inhibit human TRPM6 promoter activity. In the presence of actinomycin D, a transcriptional inhibitor, rapamycin accelerated the decrease in TRPM6 mRNA. Rapamycin decreased the expression and activity of a luciferase linked with the 3'-untranslated region of human TRPM6 mRNA. These results suggest that TRPM6 expression is up-regulated by a PI3K/Akt/mTOR pathway and rapamycin reduces TRPM6 mRNA stability, resulting in a decrease in the reabsorption of Mg2+. PMID:21073857

  11. Electrocatalytic Reduction of CO2 by Group 6 M(CO)6 Species without "Non-Innocent" Ligands.

    PubMed

    Grice, Kyle A; Saucedo, Cesar

    2016-06-20

    To understand the electrocatalytic CO2 reduction of metal carbonyl complexes without "non-innocent" ligands, the electrochemical responses of group 6 M(CO)6 (M = Cr, Mo, or W) and group 7 M2(CO)10 (M = Mn or Re) complexes were examined under Ar and CO2 at a glassy carbon electrode. All of the complexes showed changes in their cyclic voltammograms under CO2. The group 6 hexacarbonyl species show a significant increase in current under CO2 during metal-based reduction, corresponding to catalytic reduction of CO2. Bulk electrolysis experiments with Mo(CO)6 showed that CO was the primary product. The group 7 dimers showed very little change during metal-based reduction, but return oxidation responses disappeared, indicative of a chemical reaction after exposure to CO2 without catalysis. Addition of H2O, a proton source, to the solutions under CO2 decreased the catalytic current of the group 6 carbonyls and had no effect on the responses of the group 7 carbonyls. The group 6 M(CO)6 species are notable in that that they are effective catalysts without the need for an added "non-innocent" ligand such as 2,2'-bipyridine. PMID:27227447

  12. WASTE PACKAGE TRANSPORTER DESIGN

    SciTech Connect

    D.C. Weddle; R. Novotny; J. Cron

    1998-09-23

    The purpose of this Design Analysis is to develop preliminary design of the waste package transporter used for waste package (WP) transport and related functions in the subsurface repository. This analysis refines the conceptual design that was started in Phase I of the Viability Assessment. This analysis supports the development of a reliable emplacement concept and a retrieval concept for license application design. The scope of this analysis includes the following activities: (1) Assess features of the transporter design and evaluate alternative design solutions for mechanical components. (2) Develop mechanical equipment details for the transporter. (3) Prepare a preliminary structural evaluation for the transporter. (4) Identify and recommend the equipment design for waste package transport and related functions. (5) Investigate transport equipment interface tolerances. This analysis supports the development of the waste package transporter for the transport, emplacement, and retrieval of packaged radioactive waste forms in the subsurface repository. Once the waste containers are closed and accepted, the packaged radioactive waste forms are termed waste packages (WP). This terminology was finalized as this analysis neared completion; therefore, the term disposal container is used in several references (i.e., the System Description Document (SDD)) (Ref. 5.6). In this analysis and the applicable reference documents, the term ''disposal container'' is synonymous with ''waste package''.

  13. Developing Large CAI Packages.

    ERIC Educational Resources Information Center

    Reed, Mary Jac M.; Smith, Lynn H.

    1983-01-01

    When developing large computer-assisted instructional (CAI) courseware packages, it is suggested that there be more attentive planning to the overall package design before actual lesson development is begun. This process has been simplified by modifying the systems approach used to develop single CAI lessons, followed by planning for the…

  14. NRF TRIGA packaging

    SciTech Connect

    Clements, M.D.

    1995-11-01

    Training Reactor Isotopes, General Atomics (TRIGA{reg_sign}) Reactors are in use at four US Department of Energy (DOE) complex facilities and at least 23 university, commercial, or government facilities. The development of the Neutron Radiography Facility (NRF) TRIGA packaging system began in October 1993. The Hanford Site NRF is being shut down and requires an operationally user-friendly transportation and storage packaging system for removal of the TRIGA fuel elements. The NRF TRIGA packaging system is designed to remotely remove the fuel from the reactor and transport the fuel to interim storage (up to 50 years) on the Hanford Site. The packaging system consists of a cask and an overpack. The overpack is used only for transport and is not necessary for storage. Based upon the cask`s small size and light weight, small TRIGA reactors will find it versatile for numerous refueling and fuel storage needs. The NRF TRIGA packaging design also provides the basis for developing a certifiable and economical packaging system for other TRIGA reactor facilities. The small size of the NRF TRIGA cask also accommodates placing the cask into a larger certified packaging for offsite transport. The Westinghouse Hanford Company NRF TRIGA packaging, as described herein can serve other DOE sites for their onsite use, and the design can be adapted to serve university reactor facilities, handling a variety of fuel payloads.

  15. The West: Curriculum Package.

    ERIC Educational Resources Information Center

    Public Broadcasting Service, Alexandria, VA.

    This document consists of the printed components only of a PBS curriculum package intended to be used with the 9-videotape PBS documentary series entitled "The West." The complete curriculum package includes a teacher's guide, lesson plans, a student guide, audio tapes, a video index, and promotional poster. The teacher's guide and lesson plans…

  16. Modular electronics packaging system

    NASA Technical Reports Server (NTRS)

    Hunter, Don J. (Inventor)

    2001-01-01

    A modular electronics packaging system includes multiple packaging slices that are mounted horizontally to a base structure. The slices interlock to provide added structural support. Each packaging slice includes a rigid and thermally conductive housing having four side walls that together form a cavity to house an electronic circuit. The chamber is enclosed on one end by an end wall, or web, that isolates the electronic circuit from a circuit in an adjacent packaging slice. The web also provides a thermal path between the electronic circuit and the base structure. Each slice also includes a mounting bracket that connects the packaging slice to the base structure. Four guide pins protrude from the slice into four corresponding receptacles in an adjacent slice. A locking element, such as a set screw, protrudes into each receptacle and interlocks with the corresponding guide pin. A conduit is formed in the slice to allow electrical connection to the electronic circuit.

  17. [Organoleptic analysis of food packaging].

    PubMed

    Stelmach, Agnieszka; Cwiek-Ludwicka, Kazimiera

    2006-01-01

    The basic rules for the organoleptic analysis of food contact materials and food packaging and the criteria of their assessment was presented. According to the EU legislation food contact materials can not release their constituents into the food in quantities that can be harmful for the consumers and/or can change the organoleptic characteristics of food. Conformity of food contact materials and food packaging with the regulation for overall and specific migration and organoleptic characteristics should be shown by their performance in relevant tests. The standardised method for the organoleptic analysis of the food contact materials does not exist in the UE. Member States use the own methods published as national standards. For sensory analysis of foreign taste and odour Poland uses the triangle method according to Polish Standard PN-87/O-79114. Some countries use Robinson test according to German Standard DIN 10955. These two tests are basing on the same principle. Food contact materials and food packaging, which give negative results in sensory analysis can not be used in direct contact with food, even though all testing parameters in overall and specific migration were fulfil the requirements for the permissible limits. PMID:17713198

  18. Packaging Concerns/Techniques for Large Devices

    NASA Technical Reports Server (NTRS)

    Sampson, Michael J.

    2009-01-01

    This slide presentation reviews packaging challenges and options for electronic parts. The presentation includes information about non-hermetic packages, space challenges for packaging and complex package variations.

  19. TSF Interface Package

    SciTech Connect

    2004-03-01

    A collection of packages of classes for interfacing to sparse and dense matrices, vectors and graphs, and to linear operators. TSF (via TSFCore, TSFCoreUtils and TSFExtended) provides the application programmer interface to any number of solvers, linear algebra libraries and preconditioner packages, providing also a sophisticated technique for combining multiple packages to solve a single problem. TSF provides a collection of abstract base classes that define the interfaces to abstract vector, matrix and linear soerator objects. By using abstract interfaces, users of TSF are not limiting themselves to any one concrete library and can in fact easily combine multiple libraries to solve a single problem.

  20. Seawater Chemistry Package

    2005-11-23

    SeaChem Seawater Chemistry package provides routines to calculate pH, carbonate chemistry, density, and other quantities for seawater, based on the latest community standards. The chemistry is adapted from fortran routines provided by the OCMIP3/NOCES project, details of which are available at http://www.ipsl.jussieu.fr/OCMIP/. The SeaChem package can generate Fortran subroutines as well as Python wrappers for those routines. Thus the same code can be used by Python or Fortran analysis packages and Fortran ocean models alike.

  1. Optoelectronic packaging: A review

    SciTech Connect

    Carson, R.F.

    1993-09-01

    Optoelectronics and photonics hold great potential for high data-rate communication and computing. Wide using in computing applications was limited first by device technologies and now suffers due to the need for high-precision, mass-produced packaging. The use of phontons as a medium of communication and control implies a unique set of packaging constraints that was not present in traditional telecommunications applications. The state-of-the-art in optoelectronic packaging is now driven by microelectric techniques that have potential for low cost and high volume manufacturing.

  2. Spectral investigation of a group of new cataclysmic variables from the first Byurakan survey with the 6-m telescope

    SciTech Connect

    Kopylov, I.M.; Lipovetskii, V.A.; Somov, N.N.; Somova, T.A.; Stepanyan, D.A.

    1988-09-01

    The paper gives the results of preliminary spectral investigations made with the 6-m telescope for seven stellar objects identified in the First Byurakan Survey (FBS) on the basis of the ultraviolet excess in their spectra. We have classified six of these seven stars as cataclysmic variables. The objects are divided into subclasses: three are dwarf novas, one is a recurrent nova, and two are novalike. One of the stars, FBS 1031 + 590, is, on the basis of all features of the spectrum and the nature of its variability, a polar. Finding charts and samples of spectral scans of the stars are given.

  3. Impact of spin-orbit coupling on the magnetism of Sr3MIrO6 (M = Ni, Co)

    PubMed Central

    Ou, Xuedong; Wu, Hua

    2014-01-01

    Iridates are of current great interest for their entangled spin-orbital state and possibly exotic properties. In this work, using density functional calculations, we have demonstrated that the hexagonal spin-chain materials Sr3MIrO6 (M = Ni, Co) are an iridate system in which the spin-orbit coupling (SOC) tunes the magnetic and electronic properties. The significant SOC alters the orbital state, the exchange pathway, and thus the magnetic structure. This work clarifies the nature and the origin of the intra-chain antiferromagnetism of Sr3MIrO6 and well accounts for the most recent experiments. PMID:24714376

  4. The effect of nuclear reaction rates and convective mixing on the evolution of a 6M{sub ȯ} star

    SciTech Connect

    Halabi, Ghina M.

    2014-05-09

    We present the evolution of a 6M{sub ȯ} star, of solar-like initial metallicity, and investigate the effects of key nuclear reaction rates, as well as the treatment of the convective mixing on its evolution along the Cepheid instability strip. In particular, we study the effect of recent estimates of the {sup 14}N(p,γ){sup 15}O reaction on the formation and extension of the blue loop during core helium burning. We also investigate the effects induced on this blue loop by the adoption of non-standard convective mixing prescriptions, as well as the implications of modifying the Mixing Length Theory.

  5. Completion of the Radioactive Materials Packaging Handbook

    SciTech Connect

    Shappert, L.B.

    1998-02-01

    The Radioactive Materials Packaging Handbook: Design, Operation and Maintenance, which will serve as a replacement for the Cask Designers Guide (Shappert, 1970), has now been completed and submitted to the Oak Ridge National Laboratory (ORNL) electronics publishing group for layout and printing; it is scheduled to be printed in late spring 1998. The Handbook, written by experts in their particular fields, is a compilation of technical chapters that address the design aspects of a package intended for transporting radioactive material in normal commerce; it was prepared under the direction of M. E. Wangler of the US Department of Energy (DOE) and is intended to provide a wealth of technical guidance that will give designers a better understanding of the regulatory approval process, preferences of regulators on specific aspects of package design, and the types of analyses that should be considered when designing a package to carry radioactive materials.

  6. Packaging for Posterity.

    ERIC Educational Resources Information Center

    Sias, Jim

    1990-01-01

    A project in which students designed environmentally responsible food packaging is described. The problem definition; research on topics such as waste paper, plastic, metal, glass, incineration, recycling, and consumer preferences; and the presentation design are provided. (KR)

  7. Packaging films for electronic and space-related hardware

    NASA Astrophysics Data System (ADS)

    Shon, E. M.; Hamberg, O.

    1985-08-01

    Flexible packaging films are used to bag and/or wrap precision cleaned electronic or space hardware to protect them from environmental degradation during shipping and storage. Selection of packaging films depends on a knowledge of product requirements and packaging film characteristics. The literature presently available on protective packaging films has been updated to include new materials and to amplify space-related applications. Presently available packaging film materials are compared for their various characteristics: electrostatic discharge (ESD) control, flame retardancy, water vapor transmission rate, particulate shedding, molecular contamination, and transparency. The tradeoff between product requirements and the characteristics of the packaging films available are discussed. Selection considerations are given for the application of specific materials of space hardware-related applications. Applications for intimate, environmental, and electrostatic protective packaging are discussed.

  8. Waste Package Program

    SciTech Connect

    Culbreth, W.; Ladkany, S.

    1991-07-21

    This was a progress report on the research program of waste packages at the University of Nevada, Las Vegas. The report has the overviews of what the program has done from January 1991 to June 1991, such as task assignments for personnel, equipment acquisitions, and staff meetings and travels on behalf of the project. Also, included was an abstract on the structural analysis of the waste package container design. (MB)

  9. CH Packaging Program Guidance

    SciTech Connect

    Washington TRU Solutions LLC

    2002-03-04

    The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT Shipping Package, and directly related components. This document complies with the minimum requirements as specified in TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event there is a conflict between this document and the SARP or C of C, the SARP and/or C of C shall govern. C of Cs state: ''each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.'' They further state: ''each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.'' Chapter 9.0 of the SAR P charges the WIPP Management and Operation (M&O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with 10 CFR 71.11. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. This document details the instructions to be followed to operate, maintain, and test the TRUPACT-II and HalfPACT packaging. The intent of these instructions is to standardize these operations. All users will follow these instructions or equivalent instructions that assure operations are safe and meet the requirements of the SARPs.

  10. The ENSDF Java Package

    SciTech Connect

    Sonzogni, A.A.

    2005-05-24

    A package of computer codes has been developed to process and display nuclear structure and decay data stored in the ENSDF (Evaluated Nuclear Structure Data File) library. The codes were written in an object-oriented fashion using the java language. This allows for an easy implementation across multiple platforms as well as deployment on web pages. The structure of the different java classes that make up the package is discussed as well as several different implementations.

  11. Electronic Packaging Techniques

    NASA Technical Reports Server (NTRS)

    1979-01-01

    A characteristic of aerospace system design is that equipment size and weight must always be kept to a minimum, even in small components such as electronic packages. The dictates of spacecraft design have spawned a number of high-density packaging techniques, among them methods of connecting circuits in printed wiring boards by processes called stitchbond welding and parallel gap welding. These processes help designers compress more components into less space; they also afford weight savings and lower production costs.

  12. CH Packaging Program Guidance

    SciTech Connect

    Washington TRU Solutions LLC

    2003-04-30

    The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: ''each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.'' They further state: ''each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.'' Chapter 9.0 of the SARP charges the WIPP management and operating (M&O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with 10 CFR 71.11. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. This document provides the instructions to be followed to operate, maintain, and test the TRUPACT-II and HalfPACT packaging. The intent of these instructions is to standardize operations. All users will follow these instructions or equivalent instructions that assure operations are safe and meet the requirements of the SARPs.

  13. Extension of ship accident analysis to multiple-package shipments

    SciTech Connect

    Mills, G.S.; Neuhauser, K.S.

    1997-11-01

    Severe ship accidents and the probability of radioactive material release from spent reactor fuel casks were investigated previously. Other forms of RAM, e.g., plutonium oxide powder, may be shipped in large numbers of packagings rather than in one to a few casks. These smaller, more numerous packagings are typically placed in ISO containers for ease of handling, and several ISO containers may be placed in one of several holds of a cargo ship. In such cases, the size of a radioactive release resulting from a severe collision with another ship is determined not by the likelihood of compromising a single, robust package but by the probability that a certain fraction of 10`s or 100`s of individual packagings is compromised. The previous analysis involved a statistical estimation of the frequency of accidents which would result in damage to a cask located in one of seven cargo holds in a collision with another ship. The results were obtained in the form of probabilities (frequencies) of accidents of increasing severity and of release fractions for each level of severity. This paper describes an extension of the same general method in which the multiple packages are assumed to be compacted by an intruding ship`s bow until there is no free space in the hold. At such a point, the remaining energy of the colliding ship is assumed to be dissipated by progressively crushing the RAM packagings and the probability of a particular fraction of package failures is estimated by adaptation of the statistical method used previously. The parameters of a common, well characterized packaging, the 6M with 2R inner containment vessel, were employed as an illustrative example of this analysis method. However, the method is readily applicable to other packagings for which crush strengths have been measured or can be estimated with satisfactory confidence.

  14. Comparative Packaging Study

    NASA Technical Reports Server (NTRS)

    Perchonok, Michele H.; Oziomek, Thomas V.

    2009-01-01

    Future long duration manned space flights beyond low earth orbit will require the food system to remain safe, acceptable and nutritious. Development of high barrier food packaging will enable this requirement by preventing the ingress and egress of gases and moisture. New high barrier food packaging materials have been identified through a trade study. Practical application of this packaging material within a shelf life test will allow for better determination of whether this material will allow the food system to meet given requirements after the package has undergone processing. The reason to conduct shelf life testing, using a variety of packaging materials, stems from the need to preserve food used for mission durations of several years. Chemical reactions that take place during longer durations may decrease food quality to a point where crew physical or psychological well-being is compromised. This can result in a reduction or loss of mission success. The rate of chemical reactions, including oxidative rancidity and staling, can be controlled by limiting the reactants, reducing the amount of energy available to drive the reaction, and minimizing the amount of water available. Water not only acts as a media for microbial growth, but also as a reactant and means by which two reactants may come into contact with each other. The objective of this study is to evaluate three packaging materials for potential use in long duration space exploration missions.

  15. RH Packaging Program Guidance

    SciTech Connect

    Washington TRU Solutions LLC

    2008-01-12

    The purpose of this program guidance document is to provide the technical requirements for use, operation, inspection, and maintenance of the RH-TRU 72-B Waste Shipping Package (also known as the "RH-TRU 72-B cask") and directly related components. This document complies with the requirements as specified in the RH-TRU 72-B Safety Analysis Report for Packaging (SARP), and Nuclear Regulatory Commission (NRC) Certificate of Compliance (C of C) 9212. If there is a conflict between this document and the SARP and/or C of C, the C of C shall govern. The C of C states: "...each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application." It further states: "...each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application." Chapter 9.0 of the SARP tasks the Waste Isolation Pilot Plant (WIPP) Management and Operating (M&O) Contractor with assuring the packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) §71.8, "Deliberate Misconduct." Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, "Packaging and Transportation of Radioactive Material," certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21, "Reporting of Defects and Noncompliance," regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a

  16. RH Packaging Program Guidance

    SciTech Connect

    Washington TRU Solutions LLC

    2006-11-07

    The purpose of this program guidance document is to provide the technical requirements for use, operation, inspection, and maintenance of the RH-TRU 72-B Waste Shipping Package and directly related components. This document complies with the requirements as specified in the RH-TRU 72-B Safety Analysis Report for Packaging (SARP), and Nuclear Regulatory Commission (NRC) Certificate of Compliance (C of C) 9212. If there is a conflict between this document and the SARP and/or C of C, the C of C shall govern. The C of C states: "...each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application." It further states: "...each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application." Chapter 9.0 of the SARP tasks the Waste Isolation Pilot Plant (WIPP) Management and Operating (M&O) Contractor with assuring the packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with 10 Code of Federal Regulations (CFR) §71.8, "Deliberate Misconduct." Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. In accordance with 10 CFR Part 71, "Packaging and Transportation of Radioactive Material," certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21, "Reporting of Defects and Noncompliance," regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to

  17. CH Packaging Program Guidance

    SciTech Connect

    None, None

    2009-06-01

    The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: "each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application." They further state: "each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application." Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant (WIPP) management and operating (M&O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) §71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required. In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations are

  18. CH Packaging Program Guidance

    SciTech Connect

    None, None

    2008-09-11

    The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: "each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the pplication." They further state: "each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application." Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant (WIPP) management and operating (M&O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) §71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required. In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations are

  19. EQ6 Calculations for Chemical Degradation of Navy Waste Packages

    SciTech Connect

    S. LeStrange

    1999-11-15

    The Monitored Geologic Repository Waste Package Operations of the Civilian Radioactive Waste Management System Management & Operating Contractor (CRWMS M&O) performed calculations to provide input for disposal of spent nuclear fuel (SNF) from the Navy (Refs. 1 and 2). The Navy SNF has been considered for disposal at the potential Yucca Mountain site. For some waste packages, the containment may breach (Ref. 3), allowing the influx of water. Water in the waste package may moderate neutrons, increasing the likelihood of a criticality event within the waste package. The water may gradually leach the fissile components and neutron absorbers out of the waste package. In addition, the accumulation of silica (SiO{sub 2}) in the waste package over time may further affect the neutronics of the system. This study presents calculations of the long-term geochemical behavior of waste packages containing the Enhanced Design Alternative (EDA) II inner shell, Navy canister, and basket components. The calculations do not include the Navy SNF in the waste package. The specific study objectives were to determine the chemical composition of the water and the quantity of silicon (Si) and other solid corrosion products in the waste package during the first million years after the waste package is breached. The results of this calculation will be used to ensure that the type and amount of criticality control material used in the waste package design will prevent criticality.

  20. CH Packaging Program Guidance

    SciTech Connect

    Washington TRU Solutions LLC

    2005-02-28

    The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: "each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application." They further state: "each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application." Chapter 9.0 of the SARP charges the Waste Isolation Pilot Plant (WIPP) management and operating (M&O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) §71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.

  1. Food Packaging Materials

    NASA Technical Reports Server (NTRS)

    1978-01-01

    The photos show a few of the food products packaged in Alure, a metallized plastic material developed and manufactured by St. Regis Paper Company's Flexible Packaging Division, Dallas, Texas. The material incorporates a metallized film originally developed for space applications. Among the suppliers of the film to St. Regis is King-Seeley Thermos Company, Winchester, Ma'ssachusetts. Initially used by NASA as a signal-bouncing reflective coating for the Echo 1 communications satellite, the film was developed by a company later absorbed by King-Seeley. The metallized film was also used as insulating material for components of a number of other spacecraft. St. Regis developed Alure to meet a multiple packaging material need: good eye appeal, product protection for long periods and the ability to be used successfully on a wide variety of food packaging equipment. When the cost of aluminum foil skyrocketed, packagers sought substitute metallized materials but experiments with a number of them uncovered problems; some were too expensive, some did not adequately protect the product, some were difficult for the machinery to handle. Alure offers a solution. St. Regis created Alure by sandwiching the metallized film between layers of plastics. The resulting laminated metallized material has the superior eye appeal of foil but is less expensive and more easily machined. Alure effectively blocks out light, moisture and oxygen and therefore gives the packaged food long shelf life. A major packaging firm conducted its own tests of the material and confirmed the advantages of machinability and shelf life, adding that it runs faster on machines than materials used in the past and it decreases product waste; the net effect is increased productivity.

  2. Food packages for Space Shuttle

    NASA Technical Reports Server (NTRS)

    Fohey, M. F.; Sauer, R. L.; Westover, J. B.; Rockafeller, E. F.

    1978-01-01

    The paper reviews food packaging techniques used in space flight missions and describes the system developed for the Space Shuttle. Attention is directed to bite-size food cubes used in Gemini, Gemini rehydratable food packages, Apollo spoon-bowl rehydratable packages, thermostabilized flex pouch for Apollo, tear-top commercial food cans used in Skylab, polyethylene beverage containers, Skylab rehydratable food package, Space Shuttle food package configuration, duck-bill septum rehydration device, and a drinking/dispensing nozzle for Space Shuttle liquids. Constraints and testing of packaging is considered, a comparison of food package materials is presented, and typical Shuttle foods and beverages are listed.

  3. Detecting small holes in packages

    DOEpatents

    Kronberg, James W.; Cadieux, James R.

    1996-01-01

    A package containing a tracer gas, and a method for determining the presence of a hole in the package by sensing the presence of the gas outside the package. The preferred tracer gas, especially for food packaging, is sulfur hexafluoride. A quantity of the gas is added to the package and the package is closed. The concentration of the gas in the atmosphere outside the package is measured and compared to a predetermined value of the concentration of the gas in the absence of the package. A measured concentration greater than the predetermined value indicates the presence of a hole in the package. Measuring may be done in a chamber having a lower pressure than that in the package.

  4. Detecting small holes in packages

    DOEpatents

    Kronberg, J.W.; Cadieux, J.R.

    1996-03-19

    A package containing a tracer gas, and a method for determining the presence of a hole in the package by sensing the presence of the gas outside the package are disclosed. The preferred tracer gas, especially for food packaging, is sulfur hexafluoride. A quantity of the gas is added to the package and the package is closed. The concentration of the gas in the atmosphere outside the package is measured and compared to a predetermined value of the concentration of the gas in the absence of the package. A measured concentration greater than the predetermined value indicates the presence of a hole in the package. Measuring may be done in a chamber having a lower pressure than that in the package. 3 figs.

  5. Witnessing magnetic twist with high-resolution observation from the 1.6-m New Solar Telescope.

    PubMed

    Wang, Haimin; Cao, Wenda; Liu, Chang; Xu, Yan; Liu, Rui; Zeng, Zhicheng; Chae, Jongchul; Ji, Haisheng

    2015-01-01

    Magnetic flux ropes are highly twisted, current-carrying magnetic fields. They are crucial for the instability of plasma involved in solar eruptions, which may lead to adverse space weather effects. Here we present observations of a flaring using the highest resolution chromospheric images from the 1.6-m New Solar Telescope at Big Bear Solar Observatory, supplemented by a magnetic field extrapolation model. A set of loops initially appear to peel off from an overall inverse S-shaped flux bundle, and then develop into a multi-stranded twisted flux rope, producing a two-ribbon flare. We show evidence that the flux rope is embedded in sheared arcades and becomes unstable following the enhancement of its twists. The subsequent motion of the flux rope is confined due to the strong strapping effect of the overlying field. These results provide a first opportunity to witness the detailed structure and evolution of flux ropes in the low solar atmosphere. PMID:25919706

  6. Quantitative Measurements of the Daytime Near Infrared Sky Brightness at the AEOS 3.6 m Telescope

    NASA Astrophysics Data System (ADS)

    Hart, M.; Jefferies, S.; Hope, D.; Nagy, J.; Williams, S.

    2014-09-01

    We report daytime sky brightness measurements recorded in the near infrared from the 3.6 m AEOS telescope. Measurements were made at various positions in the sky and separation angles from the sun. The detector was an InGaAs focal plane array in a FLIR SC6000 camera, with images taken through a 50 nm wide filter centered at 1250 nm as well as without any optical filter. The brightness measurements have been calibrated by reference to observations of a photometric standard star in the same bands. We discuss how these new results are motivated by the selection of optimal techniques for high-resolution imaging of satellites from the AEOS telescope.

  7. A growth mechanism of porous film formed on Al in 0.6 M oxalic acid electrolyte.

    PubMed

    Han, Seong Ho; Kim, Hyoung Chan

    2012-04-01

    Understanding of mechanism of porous film formation is of fundamental importance for anodizing in general because, the onset of pore initiation terminates the barrier film growth process over the macroscopic metal surface. Several mechanisms have been proposed to explain pore formation. They include direct injection of aluminum ions into electrolyte and a field-assisted dissolution mechanism. High-resolution scanning electron microscopy of anodized surfaces and direct TEM of ion beam thinned films and ultrarmicrotomed film sections have been employed to gain further insight into the mechanism of initial porous film growth in 0.6 M oxalic acid. From detailed examination of the behavior of the xenon-tagged layer in the film during pore initiation and development in oxalic acid, the film structure of the barrier layer is found to be unstable during pore initiation and the instability of the film structure is possibly related to the field-assisted structure modification process. PMID:22849190

  8. Ultra-narrow Negative Flare Front Observed in Helium-10830 Å Using the 1.6 m New Solar Telescope

    NASA Astrophysics Data System (ADS)

    Xu, Yan; Cao, Wenda; Ding, Mingde; Kleint, Lucia; Su, Jiangtao; Liu, Chang; Ji, Haisheng; Chae, Jongchul; Jing, Ju; Cho, Kyuhyoun; Cho, Kyungsuk; Gary, Dale; Wang, Haimin

    2016-03-01

    Solar flares are sudden flashes of brightness on the Sun and are often associated with coronal mass ejections and solar energetic particles that have adverse effects on the near-Earth environment. By definition, flares are usually referred to as bright features resulting from excess emission. Using the newly commissioned 1.6 m New Solar Telescope at Big Bear Solar Observatory, we show a striking “negative” flare with a narrow but unambiguous “dark” moving front observed in He i 10830 Å, which is as narrow as 340 km and is associated with distinct spectral characteristics in Hα and Mg ii lines. Theoretically, such negative contrast in He i 10830 Å can be produced under special circumstances by nonthermal electron collisions or photoionization followed by recombination. Our discovery, made possible due to unprecedented spatial resolution, confirms the presence of the required plasma conditions and provides unique information in understanding the energy release and radiative transfer in astronomical objects.

  9. Design and Fabrication of a Supporting Structure for 3.6m Long Nb3Sn Racetrack Coils

    SciTech Connect

    Ambrosio, G.; Anerella, M.; Barzi, E.; Caspi, Shlomo; Cheng, Daniel; Dietderich, Daniel; Gourlay, Steve; Hafalia, A. Ray; Hannaford, Charles; Lietzke, Alan; Nobrega, A.R.; Sabbi, GianLuca; Schmalzle, J.; Wanderer, R. J; Zlobin, A.V.; Ferracin, P.

    2007-06-01

    As part of the LHC Accelerator Research Program (LARP), three US national laboratories (BNL, FNAL, and LBNL) are currently engaged in the development of superconducting magnets for the LHC Interaction Regions (IR) beyond the current design. As a first step towards the development of long Nb{sub 3}Sn quadrupole magnets, a 3.6 m long structure, based on the LBNL Subscale Common-Coil Magnet design, will be fabricated, assembled, and tested with aluminum-plate 'dummy coils'. The structure features an aluminum shell pre-tensioned over iron yokes using pressurized bladders and locking keys (bladder and key technology). Pre-load homogeneity and mechanical responses are monitored with pressure sensitive films and strain gauges mounted on the aluminum shell and the dummy coils. The details of the design and fabrication are presented and discussed, and the expected mechanical behavior is analyzed with finite element models.

  10. Ultra-Narrow Negative Flare Front Observed in Helium-10830 Å Using the1.6m New Solar Telescope

    NASA Astrophysics Data System (ADS)

    Xu, Yan; Cao, Wenda; Ding, Mingde; Kleint, Lucia; Su, Jiangtao; Liu, Chang; Ji, Haisheng; Chae, Jongchul; Jing, Ju; Cho, Kyuhyoun; Cho, Kyung-Suk; Gary, Dale E.; Wang, Haimin

    2016-05-01

    Solar flares are sudden flashes of brightness on the Sun and are often associated with coronal mass ejections and solar energetic particles that have adverse effects on the near-Earth environment. By definition, flares are usually referred to as bright features resulting from excess emission. Using the newly commissioned 1.6-m New Solar Telescope at Big Bear Solar Observatory, we show a striking “negative” flare with a narrow but unambiguous “dark” moving front observed in He I 10830 Å, which is as narrow as 340 km and is associated with distinct spectral characteristics in Hα and Mg II lines. Theoretically, such negative contrast in He I 10830 Å can be produced under special circumstances by nonthermal electron collisions or photoionization followed by recombination. Our discovery, made possible due to unprecedented spatial resolution, confirms the presence of the required plasma conditions and provides unique information in understanding the energy release and radiative transfer in solar flares.

  11. Witnessing magnetic twist with high-resolution observation from the 1.6-m New Solar Telescope

    PubMed Central

    Wang, Haimin; Cao, Wenda; Liu, Chang; Xu, Yan; Liu, Rui; Zeng, Zhicheng; Chae, Jongchul; Ji, Haisheng

    2015-01-01

    Magnetic flux ropes are highly twisted, current-carrying magnetic fields. They are crucial for the instability of plasma involved in solar eruptions, which may lead to adverse space weather effects. Here we present observations of a flaring using the highest resolution chromospheric images from the 1.6-m New Solar Telescope at Big Bear Solar Observatory, supplemented by a magnetic field extrapolation model. A set of loops initially appear to peel off from an overall inverse S-shaped flux bundle, and then develop into a multi-stranded twisted flux rope, producing a two-ribbon flare. We show evidence that the flux rope is embedded in sheared arcades and becomes unstable following the enhancement of its twists. The subsequent motion of the flux rope is confined due to the strong strapping effect of the overlying field. These results provide a first opportunity to witness the detailed structure and evolution of flux ropes in the low solar atmosphere. PMID:25919706

  12. Applications of Nanomaterials in Food Packaging.

    PubMed

    Bumbudsanpharoke, Nattinee; Choi, Jungwook; Ko, Seonghyuk

    2015-09-01

    Nanomaterials have drawn great interest in recent years due to their extraordinary properties that make them advantageous in food packaging applications. Specifically, nanoparticles can impart significant barrier properties, as well as mechanical, optical, catalytic, and antimicrobial properties into packaging. Silver nanoparticles (AgNPs) and nanoclay account for the majority of the nano-enabled food packaging on the market, while others, such as nano-zinc oxide (ZnO) and titanium, share less of the current market. In current food packaging, these nanomaterials are primarily used to impart antimicrobial function and to improve barrier properties, thereby extending the shelf life and freshness of packaged food. On the other hand, there is growing concern about the migration of nanomaterials from food contact materials to foodstuffs and its associated potential risks. Indeed, insufficient data about environmental and human safety assessments of migration and exposure of nanomaterials are hindering their market growth. To overcome this barrier, the public believes that legislation from government agencies is critical. This review provides an overview of the characteristics and functions of major nanomaterials that are commonly applied to food packaging, including available and near- future products. Migration research, safety issues, and public concerns are also discussed. PMID:26716190

  13. CH Packaging Program Guidance

    SciTech Connect

    None, None

    2006-04-25

    The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package TransporterModel II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: "each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application." They further state: "each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application." Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant| (WIPP) management and operating (M&O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations(CFR) §71.8. Any time a user suspects or has indications that the conditions ofapproval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations are

  14. CH Packaging Program Guidance

    SciTech Connect

    None, None

    2007-12-13

    The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: "each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application." They further state: "each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application." Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant (WIPP) management and operating (M&O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) §71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations are

  15. Geometric Modeling, Radiation Simulation, Rendering, Analysis Package

    1995-01-17

    RADIANCE is intended to aid lighting designers and architects by predicting the light levels and appearance of a space prior to construction. The package includes programs for modeling and translating scene geometry, luminaire data and material properties, all of which are needed as input to the simulation. The lighting simulation itself uses ray tracing techniques to compute radiance values (ie. the quantity of light passing through a specific point in a specific direction), which aremore » typically arranged to form a photographic quality image. The resulting image may be analyzed, displayed and manipulated within the package, and converted to other popular image file formats for export to other packages, facilitating the production of hard copy output.« less

  16. TSF Interface Package

    2004-03-01

    A collection of packages of classes for interfacing to sparse and dense matrices, vectors and graphs, and to linear operators. TSF (via TSFCore, TSFCoreUtils and TSFExtended) provides the application programmer interface to any number of solvers, linear algebra libraries and preconditioner packages, providing also a sophisticated technique for combining multiple packages to solve a single problem. TSF provides a collection of abstract base classes that define the interfaces to abstract vector, matrix and linear soeratormore » objects. By using abstract interfaces, users of TSF are not limiting themselves to any one concrete library and can in fact easily combine multiple libraries to solve a single problem.« less

  17. Determination of Fire Enviroment in Stacked Cargo Containers with Radioactive Materials Packages

    SciTech Connect

    Arviso, M.; Bobbe, J.G.; Dukart, R.D.; Koski, J.A.

    1999-05-01

    Results from a Fire Test with a three-by-three stack of standard 6 m long International Standards Organization shipping containers containing combustible fuels and empty radioactive materials packages are reported and discussed. The stack is intended to simulate fire conditions that could occur during on-deck stowage on container cargo ships. The fire is initated by locating the container stack adjacent to a 9.8 x 6 m pool fire. Temperatures of both cargoes (empty and simulated radioactive materials packages) and containers are recorded and reported. Observations on the duration, intensity and spread of the fire are discussed. Based on the results, models for simulation of fire exposure of radioactive materials packages in such fires are suggested.

  18. Packaging Concerns and Techniques for Large Devices: Challenges for Complex Electronics

    NASA Technical Reports Server (NTRS)

    LaBel, Kenneth A.; Sampson, Michael J.

    2010-01-01

    NASA is going to have to accept the use of non-hermetic packages for complex devices. There are a large number of packaging options available. Space application subjects the packages to stresses that they were probably not designed for (vacuum for instance). NASA has to find a way of having assurance in the integrity of the packages. There are manufacturers interested in qualifying non-hermetic packages to MIL-PRF-38535 Class V. Government space users are agreed that Class V should be for hermetic packages only. NASA is working on a new Class for non-hermetic packages for M38535 Appendix B, "Class Y". Testing for package integrity will be required but can be package specific as described by a Package Integrity Test Plan. The plan is developed by the manufacturer and approved by DSCC and government space.

  19. SPHINX experimenters information package

    SciTech Connect

    Zarick, T.A.

    1996-08-01

    This information package was prepared for both new and experienced users of the SPHINX (Short Pulse High Intensity Nanosecond X-radiator) flash X-Ray facility. It was compiled to help facilitate experiment design and preparation for both the experimenter(s) and the SPHINX operational staff. The major areas covered include: Recording Systems Capabilities,Recording System Cable Plant, Physical Dimensions of SPHINX and the SPHINX Test cell, SPHINX Operating Parameters and Modes, Dose Rate Map, Experiment Safety Approval Form, and a Feedback Questionnaire. This package will be updated as the SPHINX facilities and capabilities are enhanced.

  20. Waste Package Component Design Methodology Report

    SciTech Connect

    D.C. Mecham

    2004-07-12

    requirements of the YMP. Four waste package configurations have been selected to illustrate the application of the methodology during the licensing process. These four configurations are the 21-pressurized water reactor absorber plate waste package (21-PWRAP), the 44-boiling water reactor waste package (44-BWR), the 5 defense high-level radioactive waste (HLW) DOE spent nuclear fuel (SNF) codisposal short waste package (5-DHLWDOE SNF Short), and the naval canistered SNF long waste package (Naval SNF Long). Design work for the other six waste packages will be completed at a later date using the same design methodology. These include the 24-boiling water reactor waste package (24-BWR), the 21-pressurized water reactor control rod waste package (21-PWRCR), the 12-pressurized water reactor waste package (12-PWR), the 5 defense HLW DOE SNF codisposal long waste package (5-DHLWDOE SNF Long), the 2 defense HLW DOE SNF codisposal waste package (2-MC012-DHLW), and the naval canistered SNF short waste package (Naval SNF Short). This report is only part of the complete design description. Other reports related to the design include the design reports, the waste package system description documents, manufacturing specifications, and numerous documents for the many detailed calculations. The relationships between this report and other design documents are shown in Figure 1.

  1. Shipment of Small Quantities of Unspecified Radioactive Material in Chalfant Packagings

    SciTech Connect

    Smith, Allen; Abramczyk, Glenn; Nathan, Steven; Bellamy, Steve

    2009-06-12

    In the post 6M era, radioactive materials package users are faced with the disciplined operations associated with use of Certified Type B packagings. Many DOE, commercial and academic programs have a requirement to ship and/or store small masses of poorly characterized or unspecified radioactive material. For quantities which are small enough to be fissile exempt and have low radiation levels, the materials could be transported in a package which provides the required containment level. Because their Chalfant type containment vessels meet the highest standard of containment (helium leak-tight), the 9975, 9977, and 9978 are capable of transporting any of these contents. The issues associated with certification of a high-integrity, general purpose package for shipping small quantities of unspecified radioactive material are discussed and certification of the packages for this mission is recommended.

  2. Lunar Dust Analysis Package - LDAP

    NASA Astrophysics Data System (ADS)

    Chalkley, S. A.; Richter, L.; Goepel, M.; Sovago, M.; Pike, W. T.; Yang, S.; Rodenburg, J.; Claus, D.

    2012-09-01

    identification of other ejecta in the vicinity of the Lander. • Atomic (Magnetic) Force Microscope - providing nano-scale measurement of the fine particles and presence of nanophase Fe which is potentially toxic to humans • Lenseless Microscope, a novel, low mass technology based on combining diffraction patterns derived from a laser illumination of the sample to give high resolution 3D images of the regolith presented. In this paper we cover the high level science requirements and explain how this has driven the overall package design as well as the specific payload features. The complex sample handling system which allows the co-located payloads to share rego-lith samples and be able to make physical measure-ment in the sub micron scale. The use of micro-machining and MEMS technology is covered. The paper also discusses the harsh environmental conditions at the Lunar South Pole and the impact this has on the operation and survivability of an externally mounted package. The expected performance of the whole package, including the use of LIBS under lunar vacuum conditions is also presented.

  3. Antimicrobial seafood packaging: a review.

    PubMed

    Singh, Suman; Ho Lee, Myung; Park, Lnsik; Shin, Yangjai; Lee, Youn Suk

    2016-06-01

    Microorganisms are the major cause of spoilage in most seafood products; however, only few microbes, called the specific spoilage organisms (SSOs), contribute to the offensive off-flavors associated with seafood spoilage. In food, microbial degradation manifests itself as spoilage, or changes in the sensory properties of a food product, rendering it unsuitable for human consumption. The use of antimicrobial substances can control the general microflora as well as specific microorganisms related to spoilage to provide products with higher safety and better quality. Many antimicrobial compounds have been evaluated in film structures for use in seafood, especially organic acids and their salts, enzymes, bacteriocins; some studies have considered inorganic compounds such as AgSiO2, zinc oxide, silver zeolite, and titanium oxide. The characteristics of some organic antimicrobial packaging systems for seafood and their antimicrobial efficiency in film structures are reviewed in this article. PMID:27478206

  4. Aircraft sensor analysis package system description

    NASA Technical Reports Server (NTRS)

    Forman, M. L.

    1977-01-01

    An overview of the capabilities of the Aircraft Sensor Analysis Package (ASAP) is presented. The approach is non-technical, and several output products are illustrated. The major features of the system are described in more detail than is found in the User's Guide to a potential user, or to a user looking for a specific capability to be incorporated in another system.

  5. The Library Skills Learning Package: An Evaluation.

    ERIC Educational Resources Information Center

    Jenkins, Kathleen H.

    This study evaluated the effectiveness of the Library Skills Learning Package, a printed, self-contained instructional program consisting of explanations and procedures for use of specific library resources and exercises which require the student to use a source in order to answer the questions. It was tested in a special communications class…

  6. AN ADA NAMELIST PACKAGE

    NASA Technical Reports Server (NTRS)

    Klumpp, A. R.

    1994-01-01

    The Ada Namelist Package, developed for the Ada programming language, enables a calling program to read and write FORTRAN-style namelist files. A namelist file consists of any number of assignment statements in any order. Features of the Ada Namelist Package are: the handling of any combination of user-defined types; the ability to read vectors, matrices, and slices of vectors and matrices; the handling of mismatches between variables in the namelist file and those in the programmed list of namelist variables; and the ability to avoid searching the entire input file for each variable. The principle user benefits of this software are the following: the ability to write namelist-readable files, the ability to detect most file errors in the initialization phase, a package organization that reduces the number of instantiated units to a few packages rather than to many subprograms, a reduced number of restrictions, and an increased execution speed. The Ada Namelist reads data from an input file into variables declared within a user program. It then writes data from the user program to an output file, printer, or display. The input file contains a sequence of assignment statements in arbitrary order. The output is in namelist-readable form. There is a one-to-one correspondence between namelist I/O statements executed in the user program and variables read or written. Nevertheless, in the input file, mismatches are allowed between assignment statements in the file and the namelist read procedure statements in the user program. The Ada Namelist Package itself is non-generic. However, it has a group of nested generic packages following the nongeneric opening portion. The opening portion declares a variety of useraccessible constants, variables and subprograms. The subprograms are procedures for initializing namelists for reading, reading and writing strings. The subprograms are also functions for analyzing the content of the current dataset and diagnosing errors. Two nested

  7. 49 CFR 173.206 - Packaging requirements for chlorosilanes.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... are authorized: Outer packagings: Steel drum: 1A2 Plastic drum: 1H2 Plywood drum: 1D Fiber drum: 1G... transportation by passenger aircraft, the following single packagings are authorized: Steel drum: 1A1 Steel jerrican: 3A1 Plastic receptacle in steel drum: 6HA1 Cylinders (for liquids in PG I), specification or...

  8. 49 CFR 173.206 - Packaging requirements for chlorosilanes.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... are authorized: Outer packagings: Steel drum: 1A2 Plastic drum: 1H2 Plywood drum: 1D Fiber drum: 1G... transportation by passenger aircraft, the following single packagings are authorized: Steel drum: 1A1 Steel jerrican: 3A1 Plastic receptacle in steel drum: 6HA1 Cylinders (for liquids in PG I), specification or...

  9. 49 CFR 173.206 - Packaging requirements for chlorosilanes.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... are authorized: Outer packagings: Steel drum: 1A2 Plastic drum: 1H2 Plywood drum: 1D Fiber drum: 1G... transportation by passenger aircraft, the following single packagings are authorized: Steel drum: 1A1 Steel jerrican: 3A1 Plastic receptacle in steel drum: 6HA1 Cylinders (for liquids in PG I), specification or...

  10. 49 CFR 173.206 - Packaging requirements for chlorosilanes.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... are authorized: Outer packagings: Steel drum: 1A2 Plastic drum: 1H2 Plywood drum: 1D Fiber drum: 1G... transportation by passenger aircraft, the following single packagings are authorized: Steel drum: 1A1 Steel jerrican: 3A1 Plastic receptacle in steel drum: 6HA1 Cylinders (for liquids in PG I), specification or...

  11. Perovskite LaPbMSbO{sub 6} (M=Co, Ni): Structural distortion, magnetic and dielectric properties

    SciTech Connect

    Bai, Yijia; Han, Lin; Liu, Xiaojuan; Deng, Xiaolong; Wu, Xiaojie; Yao, Chuangang; Liang, Qingshuang; Meng, Junling; Meng, Jian

    2014-09-15

    The B-site ordered double perovskite oxides LaPbMSbO{sub 6} (M=Co, Ni) have been synthesized via the modified Sol–Gel precursor two-step route. Rietveld refinements reveal strong abnormal structural distortion and BO{sub 6} octahedral deformation appearing along the ab plane. Owing to the cooperative Jahn–Teller effect of Co{sup 2+} and Pb{sup 2+} ions, the Co-related compound exhibits almost complete Co{sup 2+}–Sb{sup 5+} order. For magnetic properties, spin-canted antiferromagnetic state with high extent of magnetic frustration is confirmed. The Ni-related compound presents heavier magnetic frustration for introducing tiny disorder on site occupation accompanied with valence state and further enhancing the complexity of magnetic competition. Dielectric measurements present a considerable temperature dependent dielectric relaxation with great dc-like loss feature in the LaPbCoSbO{sub 6}. For LaPbNiSbO{sub 6}, however, the permittivity with low dielectric loss is shown to be insensitive to either temperature or frequency. The corresponding electronic active energy manifests that the weakly bounded 3d-electron is prone to hop in a more distorted Co–Sb sublattice. - Graphical abstract: XRD Rietveld refinement result of LaPbCoSbO{sub 6} presented a large BO{sub 6} octahedral distortion along the ab plane. Based upon the variations from Co–O–Sb bond angles, a fierce competition from many extended magnetic coupling routes (M–O–O–M) would induce a considerably large magnetic frustration and electron hopping restriction. - Highlights: • Highly ordered LaPbMSbO{sub 6} (M=Co, Ni) were synthesized. • Abnormal structural distortion appeared in the ab plane. • Strong magnetic frustration was confirmed via M{sup 2+}–O–O–M{sup 2+} route. • Dielectric measurements presented a large difference between Co and Ni samples. • 3d-electronic structure determines lattice distortion and physical properties.

  12. BALLISTICS TESTING OF THE 9977 SHIPPING PACKAGE FOR STORAGE APPLICATIONS

    SciTech Connect

    Loftin, B.; Abramczyk, G.; Koenig, R.

    2012-06-06

    Radioactive materials are stored in a variety of locations throughout the DOE complex. At the Savannah River Site (SRS), materials are stored within dedicated facilities. Each of those facilities has a documented safety analysis (DSA) that describes accidents that the facility and the materials within it may encounter. Facilities at the SRS are planning on utilizing the certified Model 9977 Shipping Package as a long term storage package and one of these facilities required ballistics testing. Specifically, in order to meet the facility DSA, the radioactive materials (RAM) must be contained within the storage package after impact by a .223 caliber round. In order to qualify the Model 9977 Shipping Package for storage in this location, the package had to be tested under these conditions. Over the past two years, the Model 9977 Shipping Package has been subjected to a series of ballistics tests. The purpose of the testing was to determine if the 9977 would be suitable for use as a storage package at a Savannah River Site facility. The facility requirements are that the package must not release any of its contents following the impact in its most vulnerable location by a .223 caliber round. A package, assembled to meet all of the design requirements for a certified 9977 shipping configuration and using simulated contents, was tested at the Savannah River Site in March of 2011. The testing was completed and the package was examined. The results of the testing and examination are presented in this paper.

  13. TYPE A FISSILE PACKAGING FOR AIR TRANSPORT PROJECT OVERVIEW

    SciTech Connect

    Eberl, K.; Blanton, P.

    2013-10-11

    This paper presents the project status of the Model 9980, a new Type A fissile packaging for use in air transport. The Savannah River National Laboratory (SRNL) developed this new packaging to be a light weight (<150-lb), drum-style package and prepared a Safety Analysis for Packaging (SARP) for submission to the DOE/EM. The package design incorporates unique features and engineered materials specifically designed to minimize packaging weight and to be in compliance with 10CFR71 requirements. Prototypes were fabricated and tested to evaluate the design when subjected to Normal Conditions of Transport (NCT) and Hypothetical Accident Conditions (HAC). An overview of the design details, results of the regulatory testing, and lessons learned from the prototype fabrication for the 9980 will be presented.

  14. Printer Graphics Package

    NASA Technical Reports Server (NTRS)

    Blanchard, D. C.

    1986-01-01

    Printer Graphics Package (PGP) is tool for making two-dimensional symbolic plots on line printer. PGP created to support development of Heads-Up Display (HUD) simulation. Standard symbols defined with HUD in mind. Available symbols include circle, triangle, quadrangle, window, line, numbers, and text. Additional symbols easily added or built up from available symbols.

  15. Electro-Microfluidic Packaging

    NASA Astrophysics Data System (ADS)

    Benavides, G. L.; Galambos, P. C.

    2002-06-01

    There are many examples of electro-microfluidic products that require cost effective packaging solutions. Industry has responded to a demand for products such as drop ejectors, chemical sensors, and biological sensors. Drop ejectors have consumer applications such as ink jet printing and scientific applications such as patterning self-assembled monolayers or ejecting picoliters of expensive analytes/reagents for chemical analysis. Drop ejectors can be used to perform chemical analysis, combinatorial chemistry, drug manufacture, drug discovery, drug delivery, and DNA sequencing. Chemical and biological micro-sensors can sniff the ambient environment for traces of dangerous materials such as explosives, toxins, or pathogens. Other biological sensors can be used to improve world health by providing timely diagnostics and applying corrective measures to the human body. Electro-microfluidic packaging can easily represent over fifty percent of the product cost and, as with Integrated Circuits (IC), the industry should evolve to standard packaging solutions. Standard packaging schemes will minimize cost and bring products to market sooner.

  16. Radioactive waste disposal package

    DOEpatents

    Lampe, Robert F.

    1986-11-04

    A radioactive waste disposal package comprising a canister for containing vitrified radioactive waste material and a sealed outer shell encapsulating the canister. A solid block of filler material is supported in said shell and convertible into a liquid state for flow into the space between the canister and outer shell and subsequently hardened to form a solid, impervious layer occupying such space.

  17. Radioactive waste disposal package

    DOEpatents

    Lampe, Robert F.

    1986-01-01

    A radioactive waste disposal package comprising a canister for containing vitrified radioactive waste material and a sealed outer shell encapsulating the canister. A solid block of filler material is supported in said shell and convertible into a liquid state for flow into the space between the canister and outer shell and subsequently hardened to form a solid, impervious layer occupying such space.

  18. CH Packaging Maintenance Manual

    SciTech Connect

    Washington TRU Solutions

    2002-01-02

    This procedure provides instructions for performing inner containment vessel (ICV) and outer containment vessel (OCV) maintenance and periodic leakage rate testing on the following packaging seals and corresponding seal surfaces using a nondestructive helium (He) leak test. In addition, this procedure provides instructions for performing ICV and OCV structural pressure tests.

  19. Project Information Packages Kit.

    ERIC Educational Resources Information Center

    RMC Research Corp., Mountain View, CA.

    Presented are an overview booklet, a project selection guide, and six Project Information Packages (PIPs) for six exemplary projects serving underachieving students in grades k through 9. The overview booklet outlines the PIP projects and includes a chart of major project features. A project selection guide reviews the PIP history, PIP contents,…

  20. Jpetra Kernel Package

    SciTech Connect

    Heroux, Michael A.

    2004-03-01

    A package of classes for constructing and using distributed sparse and dense matrices, vectors and graphs, written in Java. Jpetra is intended to provide the foundation for basic matrix and vector operations for Java developers. Jpetra provides distributed memory operations via an abstract parallel machine interface. The most common implementation of this interface will be Java sockets.

  1. Waste disposal package

    DOEpatents

    Smith, M.J.

    1985-06-19

    This is a claim for a waste disposal package including an inner or primary canister for containing hazardous and/or radioactive wastes. The primary canister is encapsulated by an outer or secondary barrier formed of a porous ceramic material to control ingress of water to the canister and the release rate of wastes upon breach on the canister. 4 figs.

  2. Automatic Differentiation Package

    2007-03-01

    Sacado is an automatic differentiation package for C++ codes using operator overloading and C++ templating. Sacado provide forward, reverse, and Taylor polynomial automatic differentiation classes and utilities for incorporating these classes into C++ codes. Users can compute derivatives of computations arising in engineering and scientific applications, including nonlinear equation solving, time integration, sensitivity analysis, stability analysis, optimization and uncertainity quantification.

  3. Package for fragile objects

    DOEpatents

    Burgeson, Duane A.

    1977-01-01

    A package for fragile objects such as radioactive fusion pellets of micron size shipped in mounted condition or unmounted condition with a frangible inner container which is supported in a second inner container which in turn is supported in a final outer container, the second inner container having recesses for supporting alternate design inner containers.

  4. Metric Education Evaluation Package.

    ERIC Educational Resources Information Center

    Kansky, Bob; And Others

    This document was developed out of a need for a complete, carefully designed set of evaluation instruments and procedures that might be applied in metric inservice programs across the nation. Components of this package were prepared in such a way as to permit local adaptation to the evaluation of a broad spectrum of metric education activities.…

  5. High Efficiency Integrated Package

    SciTech Connect

    Ibbetson, James

    2013-09-15

    Solid-state lighting based on LEDs has emerged as a superior alternative to inefficient conventional lighting, particularly incandescent. LED lighting can lead to 80 percent energy savings; can last 50,000 hours – 2-50 times longer than most bulbs; and contains no toxic lead or mercury. However, to enable mass adoption, particularly at the consumer level, the cost of LED luminaires must be reduced by an order of magnitude while achieving superior efficiency, light quality and lifetime. To become viable, energy-efficient replacement solutions must deliver system efficacies of ≥ 100 lumens per watt (LPW) with excellent color rendering (CRI > 85) at a cost that enables payback cycles of two years or less for commercial applications. This development will enable significant site energy savings as it targets commercial and retail lighting applications that are most sensitive to the lifetime operating costs with their extended operating hours per day. If costs are reduced substantially, dramatic energy savings can be realized by replacing incandescent lighting in the residential market as well. In light of these challenges, Cree proposed to develop a multi-chip integrated LED package with an output of > 1000 lumens of warm white light operating at an efficacy of at least 128 LPW with a CRI > 85. This product will serve as the light engine for replacement lamps and luminaires. At the end of the proposed program, this integrated package was to be used in a proof-of-concept lamp prototype to demonstrate the component’s viability in a common form factor. During this project Cree SBTC developed an efficient, compact warm-white LED package with an integrated remote color down-converter. Via a combination of intensive optical, electrical, and thermal optimization, a package design was obtained that met nearly all project goals. This package emitted 1295 lm under instant-on, room-temperature testing conditions, with an efficacy of 128.4 lm/W at a color temperature of ~2873

  6. Development and tests of interferometry facility in 6-m diameter radiometer thermal vacuum chamber in Tsukuba Space Center

    NASA Astrophysics Data System (ADS)

    Suganuma, Masahiro; Katayama, Haruyoshi; Naitoh, Masataka; Imai, Tadashi; Miyamoto, Masashi; Maruyama, Kenta; Kaneda, Hidehiro; Tange, Yoshio; Nakagawa, Takao

    2010-07-01

    We present a test of optical metrology for 800-mm spaceborne optics in the 6-m radiometer thermal vacuum chamber at JAXA's Tsukuba Space Center of JAXA. Under the framework of the JAXA's large-optics study program for astronomy and Earth observations, we developed a test bench for interferometric metrology of large optics with an auto-collimation method in the chamber. The optical system was aligned in a horizontal light-axis configuration within the facility limit to handle a 3.5-m aperture telescope like SPICA. A high-speed interferometer was contained in an aluminum and titanmade pressure vessel, which was mounted on the five-axis stage. We tested the 800-mm lightweight C/SiC optics using a 900-mm diameter flat mirror. Alignment changes in tilts of about ten arcseconds were observed as pressure went down from 1 atm to vacuum. After we re-aligned the interferometer and flat mirror, the wavefronts through the optics under vacuum were observed to increase in astigmatism aberration by 0.07λRMS at λ=633nm from under atmosphere, which might be caused by a deformation in the test optics or flat mirror.

  7. Unprecedented Fine Structure of a Solar Flare Revealed by the 1.6~m New Solar Telescope

    NASA Astrophysics Data System (ADS)

    Jing, Ju; Xu, Yan; Cao, Wenda; Liu, Chang; Gary, Dale E.; Wang, Haimin

    2016-05-01

    Solar flares signify the sudden release of magnetic energy and are sources of so called space weather. The fine structures (below 500 km) of flares are rarely observed and are accessible to only a few instruments world-wide. Here we present observation of a solar flare using exceptionally high resolution images from the 1.6~m New Solar Telescope (NST) equipped with high order adaptive optics at Big Bear Solar Observatory (BBSO). The observation reveals the process of the flare in unprecedented detail, including the flare ribbon propagating across the sunspots, coronal rain (made of condensing plasma) streaming down along the post-flare loops, and the chromosphere's response to the impact of coronal rain, showing fine-scale brightenings at the footpoints of the falling plasma. Taking advantage of the resolving power of the NST, we measure the cross-sectional widths of flare ribbons, post-flare loops and footpoint brighenings, which generally lie in the range of 80-200 km, well below the resolution of most current instruments used for flare studies. Confining the scale of such fine structure provides an essential piece of information in modeling the energy transport mechanism of flares, which is an important issue in solar and plasma physics.

  8. Assembly and Test of a Support Structure for 3.6 m Long Nb3Sn Racetrack Coils

    SciTech Connect

    Ambrosio, G.; Anerella, M.; Caspi, S.; Cheng, D.W.; Felice, H.; Hafalia, A.R.; Hannaford, C.R.; Lietzke, A.F.; Lizarazo, J.; Muratore, J.; Sabbi, G.L.; Schmalzle, J.; Thomas, R.; Wanderer, P.J.; Ferracin, P.

    2008-06-01

    The LHC Accelerator Research Program (LARP) is currently developing 4 m long Nb{sub 3}Sn quadrupole magnets for a possible upgrade of the LHC Interaction Regions (IR). In order to provide a reliable test bed for the fabrication and test of long Nb{sub 3}Sn coils, LARP has started the development of the long racetrack magnet LRS01. The magnet is composed of two 3.6 m long racetrack coils contained in a support structure based on an aluminum shell pre-tensioned with water-pressurized bladders and interference keys. For the phase-one test of the assembly procedure and loading operation, the structure was pre-stressed at room temperature and cooled down to 77 K with instrumented, solid aluminum 'dummy coils'. Mechanical behavior and stress homogeneity were monitored with strain gauges mounted on the shell and the dummy coils. The dummy coils were replaced with reacted and impregnated Nb{sub 3}Sn coils in a second assembly procedure, followed by cool-down to 4.5 K and powered magnet test. This paper report on the assembly and loading procedures of the support structure as well as the comparison between strain gauge data and 3D model predictions.

  9. Unprecedented Fine Structure of a Solar Flare Revealed by the 1.6 m New Solar Telescope.

    PubMed

    Jing, Ju; Xu, Yan; Cao, Wenda; Liu, Chang; Gary, Dale; Wang, Haimin

    2016-01-01

    Solar flares signify the sudden release of magnetic energy and are sources of so called space weather. The fine structures (below 500 km) of flares are rarely observed and are accessible to only a few instruments world-wide. Here we present observation of a solar flare using exceptionally high resolution images from the 1.6 m New Solar Telescope (NST) equipped with high order adaptive optics at Big Bear Solar Observatory (BBSO). The observation reveals the process of the flare in unprecedented detail, including the flare ribbon propagating across the sunspots, coronal rain (made of condensing plasma) streaming down along the post-flare loops, and the chromosphere's response to the impact of coronal rain, showing fine-scale brightenings at the footpoints of the falling plasma. Taking advantage of the resolving power of the NST, we measure the cross-sectional widths of flare ribbons, post-flare loops and footpoint brighenings, which generally lie in the range of 80-200 km, well below the resolution of most current instruments used for flare studies. Confining the scale of such fine structure provides an essential piece of information in modeling the energy transport mechanism of flares, which is an important issue in solar and plasma physics. PMID:27071459

  10. Ultra high tip speed (670.6 m/sec) fan stage with composite rotor: Aerodynamic and mechanical design

    NASA Technical Reports Server (NTRS)

    Halle, J. E.; Burger, G. D.; Dundas, R. E.

    1977-01-01

    A highly loaded, single-stage compressor having a tip speed of 670.6 m/sec was designed for the purpose of investigating very high tip speeds and high aerodynamic loadings to obtain high stage pressure ratios at acceptable levels of efficiency. The design pressure ratio is 2.8 at an adiabatic efficiency of 84.4%. Corrected design flow is 83.4 kg/sec; corrected design speed is 15,200 rpm; and rotor inlet tip diameter is 0.853 m. The rotor uses multiple-circular-arc airfoils from 0 to 15% span, precompression airfoils assuming single, strong oblique shocks from 21 to 43% span, and precompression airfoils assuming multiple oblique shocks from 52% span to the tip. Because of the high tip speeds, the rotor blades are designed to be fabricated of composite materials. Two composite materials were investigated: Courtaulds HTS graphite fiber in a Kerimid 601 polyimide matrix and the same fibers in a PMR polyimide matrix. In addition to providing a description of the aerodynamic and mechanical design of the 670.0 m/sec fan, discussion is presented of the results of structural tests of blades fabricated with both types of matrices.

  11. Packaging design criteria for the Hanford Ecorok Packaging

    SciTech Connect

    Mercado, M.S.

    1996-01-19

    The Hanford Ecorok Packaging (HEP) will be used to ship contaminated water purification filters from K Basins to the Central Waste Complex. This packaging design criteria documents the design of the HEP, its intended use, and the transportation safety criteria it is required to meet. This information will serve as a basis for the safety analysis report for packaging.

  12. MEMS performance challenges: packaging and shock tests

    NASA Astrophysics Data System (ADS)

    Chang, Jiyoung; Yang, Chen; Zhang, Bin; Lin, Liwei

    2011-06-01

    This paper describes recent advances in the MEMS performance challenges with emphases on packaging and shock tests. In the packaging area, metal to metal bonding processes have been developed to overcome limitations of the glass frit bonding by means of two specific methods: (1) pre-reflow of solder for enhanced bonding adhesion, and (2) the insertion of thin metal layer between parent metal bonding materials. In the shock test area, multiscale analysis for a MEMS package system has been developed with experimental verifications to investigate dynamic responses under drop-shock tests. Structural deformation and stress distribution data are extracted and predicted for device fracture and in-operation stiction analyses for micro mechanical components in various MEMS sensors, including accelerometers and gyroscopes.

  13. RADIOACTIVE MATERIAL PACKAGING TORQUE REQUIREMENTS COMPLIANCE

    SciTech Connect

    Watkins, R.; Leduc, D.

    2011-03-24

    Shipping containers used to transport radioactive material (RAM) in commerce employ a variety of closure mechanisms. Often, these closure mechanisms require a specific amount of torque be applied to a bolt, nut or other threaded fastener. It is important that the required preload is achieved so that the package testing and analysis is not invalidated for the purpose of protecting the public. Torque compliance is a means of ensuring closure preload, is a major factor in accomplishing the package functions of confinement/containment, sub-criticality, and shielding. This paper will address the importance of applying proper torque to package closures, discuss torque value nomenclature, and present one methodology to ensure torque compliance is achieved.

  14. RF packaging for space applications

    NASA Astrophysics Data System (ADS)

    Drevon, C.; Monfraix, P.; Paillard, M.; Schaffauser, C.; Vendier, O.

    2002-12-01

    Alcatel Space has been working in the field of RF hybrids for a long time. This paper presents the evolution of microwave packaging, up to 40 GHz, towards more and more miniaturisation. RF packaging presents challenging trade-offs between electrical performances and manufacturability, the higher the frequency; the more these two parameters are intertwined. An important step in the field of miniaturisation was the use, beginning of 90's, of MMICs based on GaAs - Gallium Arsenide - and micropackages, following by the introduction of mixed LF/MMwave MCM. Now a good choice could be made between those MCMs and advanced micropackages. The next evolution is the use of flip-chip interconnection to minimise the length of RF connections. In term of bonding reliability, the results give values over more than five times the limits from the standards, even after 500 thermal cycles. The association of power flip-chip which high thermal conductive substrates like Aluminum Nitride - could give at least 40% reduction in the Rth for an amplifier with MMIC mounted flip-chip with emitter bumps. The glob-top technology is not yet used for higher frequencies (i.e. some or some tens of GHz). However, the results presented in this paper show that glob-top are compatible with GaAs MMICs working up to 12 GHz. With some specific design rules, the right encapsulant and the associated processes, there are little degradations of the electrical performances of a Low Level Amplifier working at 10.7 - 12.7 GHz. This has been also checked after thermal cycles.Another emergent technology with MEMS - MicroElectroMechanical Systems - could be used soon for space application, especially for very small switches with low losses. This will be made only if they could be encapsulated with an adapted packaging and if the reliability is full demonstrated following space criteria. Now, those different technologies could be associated with other miniaturization new concepts adapted to the microwave needs, such

  15. RNA Encapsidation and Packaging in the Phleboviruses

    PubMed Central

    Hornak, Katherine E.; Lanchy, Jean-Marc; Lodmell, J. Stephen

    2016-01-01

    The Bunyaviridae represents the largest family of segmented RNA viruses, which infect a staggering diversity of plants, animals, and insects. Within the family Bunyaviridae, the Phlebovirus genus includes several important human and animal pathogens, including Rift Valley fever virus (RVFV), severe fever with thrombocytopenia syndrome virus (SFTSV), Uukuniemi virus (UUKV), and the sandfly fever viruses. The phleboviruses have small tripartite RNA genomes that encode a repertoire of 5–7 proteins. These few proteins accomplish the daunting task of recognizing and specifically packaging a tri-segment complement of viral genomic RNA in the midst of an abundance of host components. The critical nucleation events that eventually lead to virion production begin early on in the host cytoplasm as the first strands of nascent viral RNA (vRNA) are synthesized. The interaction between the vRNA and the viral nucleocapsid (N) protein effectively protects and masks the RNA from the host, and also forms the ribonucleoprotein (RNP) architecture that mediates downstream interactions and drives virion formation. Although the mechanism by which all three genomic counterparts are selectively co-packaged is not completely understood, we are beginning to understand the hierarchy of interactions that begins with N-RNA packaging and culminates in RNP packaging into new virus particles. In this review we focus on recent progress that highlights the molecular basis of RNA genome packaging in the phleboviruses. PMID:27428993

  16. RNA Encapsidation and Packaging in the Phleboviruses.

    PubMed

    Hornak, Katherine E; Lanchy, Jean-Marc; Lodmell, J Stephen

    2016-01-01

    The Bunyaviridae represents the largest family of segmented RNA viruses, which infect a staggering diversity of plants, animals, and insects. Within the family Bunyaviridae, the Phlebovirus genus includes several important human and animal pathogens, including Rift Valley fever virus (RVFV), severe fever with thrombocytopenia syndrome virus (SFTSV), Uukuniemi virus (UUKV), and the sandfly fever viruses. The phleboviruses have small tripartite RNA genomes that encode a repertoire of 5-7 proteins. These few proteins accomplish the daunting task of recognizing and specifically packaging a tri-segment complement of viral genomic RNA in the midst of an abundance of host components. The critical nucleation events that eventually lead to virion production begin early on in the host cytoplasm as the first strands of nascent viral RNA (vRNA) are synthesized. The interaction between the vRNA and the viral nucleocapsid (N) protein effectively protects and masks the RNA from the host, and also forms the ribonucleoprotein (RNP) architecture that mediates downstream interactions and drives virion formation. Although the mechanism by which all three genomic counterparts are selectively co-packaged is not completely understood, we are beginning to understand the hierarchy of interactions that begins with N-RNA packaging and culminates in RNP packaging into new virus particles. In this review we focus on recent progress that highlights the molecular basis of RNA genome packaging in the phleboviruses. PMID:27428993

  17. Double Perovskite Anode Materials Sr2MMoO6 (M = Co, Ni) for Solid-Oxide Fuel Cells

    SciTech Connect

    Huang, Y.; Liang, G; Croft, M; Lehtimaki, M; Karppinen, M; Goodenough, J

    2009-01-01

    Double-perovskites Sr2MMoO6 (M = Co, Ni) have been investigated as anode materials for a solid oxide fuel cell. At room temperature, both Sr2CoMoO6 and Sr2NiMoO6 are tetragonal (I4/m). X-ray absorption spectroscopy confirmed the presence of Co2+/Mo6+ and Ni2+/Mo6+ pairs in the oxygen-stoichiometric compounds. The samples contain a limited concentration of oxygen vacancies in the reducing atmospheres at an anode. Reoxidation is facile below 600 C; they become antiferromagnetic at low temperatures TN = 37 and 80 K for M = Co and Ni, respectively. As an anode with a 300 em thick La0.8Sr0.2Ga0.83Mg0.17O2.815 electrolyte and SrFe0.2Co0.8O3-d as a cathode, Sr2CoMoO6 exhibited maximum power densities of 735 mW/cm2 in H2 and 527 mW/cm2 in wet CH4 at 800 C; Sr2NiMoO6 shows a notable power output only in dry CH4. The high performance of Sr2CoMoO6 in wet CH4 may be due to its catalytic effect on steam reforming of methane, but some degradation of the structure that occurred in CH4 obscures identification of the catalytic reaction processes at the surface. However, the stronger octahedral-site preference of Ni2+ versus Co2+ can account for the lower performance of the M = Ni anode.

  18. Expression of interleukin 6 receptors and interleukin 6 mRNA by bovine leukaemia virus-induced tumour cells.

    PubMed

    Droogmans, L; Cludts, I; Cleuter, Y; Kerkhofs, P; Adam, E; Willems, L; Kettmann, R; Burny, A

    1994-11-01

    Bovine leukaemia virus (BLV) is the aetiologic agent of bovine leucosis. The virus induces malignancies of the B-cell lineage (leukaemia/lymphoma). The role played by interleukin 6 (IL-6) in the BLV-induced leukemogenesis process was evaluated. Six cell lines derived from BLV-induced tumours were tested for the expression of IL-6 receptors. Two cell lines (LB155 and YR2) display 250-300 receptor per cell (kd = 1.7 10(-10) M and 1.4 10(-10) M, respectively) whereas the other four (LB159, LB167, YR1 and M51) do not display detectable amounts of receptors. Very low (if any) expression of IL-6 receptors has been found in the case of the B lymphocytes of animals in persistent lymphocytosis (PL). Despite the presence of IL-6 receptors on the surface of LB155 and YR2 cells, no influence of exogenous IL-6 on their growth has been observed. Northern analyses indicated the presence of IL-6 transcripts only in the case of mRNA isolated from LB155 cells. Since this cell line also expresses receptors for the cytokine, an autocrine loop may exist in these cells. Experiments in which bovine and bovine epithelial cell lines were transfected with a plasmid containing the bovine IL-6 promoter controlling the expression of the reporter cat gene failed to indicate any influence of the viral transactivator p34tax on the activity of this promoter. We conclude that IL-6 receptors and IL-6 mRNA can be found in some BLV-induced tumours, but this does not correlate with viral expression in BLV-induced leukaemia/lymphoma. PMID:7893972

  19. KMTNet: a network of 1.6-m wide field optical telescopes installed at three southern observatories

    NASA Astrophysics Data System (ADS)

    Lee, Chung-Uk; Kim, Seung-Lee; Cha, Sang-Mok; Lee, Yongseok; Kim, Dong-Jin; Park, Byeong-Gon; Lee, Dong-Joo; Koo, Jae-Rim; Hong, Kyeongsoo; Lee, Jae Woo; Ryu, Yoon-Hyun; Lim, Beomdu; Lim, Jin-Sun; Gho, Seung-Won; Kim, Min-Jun

    2015-08-01

    Korea Astronomy and Space Science Institute (KASI) have installed three identical 1.6-m telescopes, called Korea Microlensing Telescope Network (KMTNet), which cover 2 x 2 degree field of view with the plate scale of 0.4 arcsec/pixel at three observatories - CTIO, SSO and SAAO in southern hemisphere. The uniqueness of the system is the uninterupted 24-hour monitoring with a wide field optics in southern hemisphere. The telescope adopts prime focus using a parabolic mirror and four spherical flattening lenses. The structural design and driving systems are modified from the degin of 2MASS telescope. The one piece filter-shutter assembly has a sliding shutter and four 310-mm square filters. Each observation system produces a 680MB size image file at site and the images are transfered to KASI data center using the Global Ring Network for Advanced Application Development (GLORIAD) network with the band width of 50Mbps in average. The main science goal of the KMTNet is to discover Earth like extra solar planet using the microlensing technique during bulge season, and 50% of the total observation time is allocated for the science program solely. The other telescope times are allocated for pre-selected seven science programs during non-bulge season. From the test observation, we verify that the most important two requirements are satisfied: 10 arcsec in RMS for the pointing accuracy and 1 arcsec of delivered image quality in I-band. In this presentation, we introduce finally installed system at each observatory and its observational performance obtained from the test observation.

  20. Sustainable Library Development Training Package

    ERIC Educational Resources Information Center

    Peace Corps, 2012

    2012-01-01

    This Sustainable Library Development Training Package supports Peace Corps' Focus In/Train Up strategy, which was implemented following the 2010 Comprehensive Agency Assessment. Sustainable Library Development is a technical training package in Peace Corps programming within the Education sector. The training package addresses the Volunteer…

  1. SAT Packages--An Update.

    ERIC Educational Resources Information Center

    Staples, Betsy

    1985-01-01

    Describes software packages used to help prepare for the Scholastic Aptitude Test, considering features that the packages have in common as well as unique features that each package has. Also lists and ranks the products and their features in a chart (indicating system requirements and current cost). (JN)

  2. Anticounterfeit packaging technologies.

    PubMed

    Shah, Ruchir Y; Prajapati, Prajesh N; Agrawal, Y K

    2010-10-01

    Packaging is the coordinated system that encloses and protects the dosage form. Counterfeit drugs are the major cause of morbidity, mortality, and failure of public interest in the healthcare system. High price and well-known brands make the pharma market most vulnerable, which accounts for top priority cardiovascular, obesity, and antihyperlipidemic drugs and drugs like sildenafil. Packaging includes overt and covert technologies like barcodes, holograms, sealing tapes, and radio frequency identification devices to preserve the integrity of the pharmaceutical product. But till date all the available techniques are synthetic and although provide considerable protection against counterfeiting, have certain limitations which can be overcome by the application of natural approaches and utilization of the principles of nanotechnology. PMID:22247875

  3. Anticounterfeit packaging technologies

    PubMed Central

    Shah, Ruchir Y.; Prajapati, Prajesh N.; Agrawal, Y. K.

    2010-01-01

    Packaging is the coordinated system that encloses and protects the dosage form. Counterfeit drugs are the major cause of morbidity, mortality, and failure of public interest in the healthcare system. High price and well-known brands make the pharma market most vulnerable, which accounts for top priority cardiovascular, obesity, and antihyperlipidemic drugs and drugs like sildenafil. Packaging includes overt and covert technologies like barcodes, holograms, sealing tapes, and radio frequency identification devices to preserve the integrity of the pharmaceutical product. But till date all the available techniques are synthetic and although provide considerable protection against counterfeiting, have certain limitations which can be overcome by the application of natural approaches and utilization of the principles of nanotechnology. PMID:22247875

  4. KAPPA -- Kernel Application Package

    NASA Astrophysics Data System (ADS)

    Currie, Malcolm J.; Berry, David. S.

    KAPPA is an applications package comprising about 180 general-purpose commands for image processing, data visualisation, and manipulation of the standard Starlink data format---the NDF. It is intended to work in conjunction with Starlink's various specialised packages. In addition to the NDF, KAPPA can also process data in other formats by using the `on-the-fly' conversion scheme. Many commands can process data arrays of arbitrary dimension, and others work on both spectra and images. KAPPA operates from both the UNIX C-shell and the ICL command language. This document describes how to use KAPPA and its features. There is some description of techniques too, including a section on writing scripts. This document includes several tutorials and is illustrated with numerous examples. The bulk of this document comprises detailed descriptions of each command as well as classified and alphabetical summaries.

  5. Design package for programmable controller and hydronic subsystem

    NASA Technical Reports Server (NTRS)

    1979-01-01

    Information used in the evaluation of design of Sunkeeper Control's electronic controllers and hydronic packages is discussed. This information includes system performance specifications, a design data brochure, drawings, and qualification and acceptance test procedures.

  6. Installation package for a solar-heating system

    NASA Technical Reports Server (NTRS)

    1980-01-01

    Package consists of installation, operation and maintenance manuals for four commercial solar energy subsystems, including flat plate solar collector pebble bed thermal-storage. Manual gives design information, sizing data, specification drawings, and other material for subsystem.

  7. Aquaculture information package

    SciTech Connect

    Boyd, T.; Rafferty, K.

    1998-08-01

    This package of information is intended to provide background information to developers of geothermal aquaculture projects. The material is divided into eight sections and includes information on market and price information for typical species, aquaculture water quality issues, typical species culture information, pond heat loss calculations, an aquaculture glossary, regional and university aquaculture offices and state aquaculture permit requirements. A bibliography containing 68 references is also included.

  8. Navy packaging standardization thrusts

    NASA Astrophysics Data System (ADS)

    Kidwell, J. R.

    1982-11-01

    Standardization is a concept that is basic to our world today. The idea of reducing costs through the economics of mass production is an easy one to grasp. Henry Ford started the process of large scale standardization in this country with the Detroit production lines for his automobiles. In the process additional benefits accrued, such as improved reliability through design maturity, off-the-shelf repair parts, faster repair time, and a resultant lower cost of ownership (lower life-cycle cost). The need to attain standardization benefits with military equipments exists now. Defense budgets, although recently increased, are not going to permit us to continue the tremendous investment required to maintain even the status quo and develop new hardware at the same time. Needed are more reliable, maintainable, testable hardware in the Fleet. It is imperative to recognize the obsolescence problems created by the use of high technology devices in our equipments, and find ways to combat these shortfalls. The Navy has two packaging standardization programs that will be addressed in this paper; the Standard Electronic Modules and the Modular Avionics Packaging programs. Following a brief overview of the salient features of each program, the packaging technology aspects of the program will be addressed, and developmental areas currently being investigated will be identified.

  9. Documentation and verification required for type A packaging use

    SciTech Connect

    O`Brien, J.H.

    1997-07-30

    This document furnishes knowledge and methods for verifying compliance with the U.S. Department of Transportation (DOT) packaging requirements for shipping Type A quantities of radioactive material. The primary emphasis is on the requirements identified in 49 CFR 173.415(a), which states, ``Each offeror of a Specification 7A package must maintain on file for at least one year after the shipment, and shall provide to DOT on request, complete documentation of tests and an engineering evaluation of comparative data showing that the construction methods, packaging design, and materials of construction comply with that specification.`` This guidance document uses a checklist to show compliance.

  10. 78 FR 19007 - Certain Products Having Laminated Packaging, Laminated Packaging, and Components Thereof...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-28

    ... COMMISSION Certain Products Having Laminated Packaging, Laminated Packaging, and Components Thereof.... 1337, on behalf of Lamina Packaging Innovations LLC of Longview, Texas. An amended complaint was filed... importation of certain products having laminated packaging, laminated packaging, and components thereof...

  11. 78 FR 13083 - Products Having Laminated Packaging, Laminated Packaging, and Components Thereof; Notice of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-02-26

    ... COMMISSION Products Having Laminated Packaging, Laminated Packaging, and Components Thereof; Notice of... Commission has received a complaint entitled Products Having Laminated ] Packaging, Laminated Packaging, and... filed on behalf of Lamina Packaging Innovations LLC on February 20, 2013. The complaint...

  12. Plutonium stabilization and packaging system

    SciTech Connect

    1996-05-01

    This document describes the functional design of the Plutonium Stabilization and Packaging System (Pu SPS). The objective of this system is to stabilize and package plutonium metals and oxides of greater than 50% wt, as well as other selected isotopes, in accordance with the requirements of the DOE standard for safe storage of these materials for 50 years. This system will support completion of stabilization and packaging campaigns of the inventory at a number of affected sites before the year 2002. The package will be standard for all sites and will provide a minimum of two uncontaminated, organics free confinement barriers for the packaged material.

  13. CFD modeling to improve safe and efficient distribution of chlorine dioxide gas for packaging fresh produce

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The efficiency of the packaging system in inactivating food borne pathogens and prolonging the shelf life of fresh-cut produce is influenced by the design of the package apart from material and atmospheric conditions. Three different designs were considered to determine a specific package design ens...

  14. 21 CFR 355.20 - Packaging conditions.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... (toothpastes and tooth powders) packages shall not contain more than 276 milligrams (mg) total fluorine per... packages shall not contain more than 120 mg total fluorine per package. (3) Exception. Package...

  15. 21 CFR 355.20 - Packaging conditions.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... (toothpastes and tooth powders) packages shall not contain more than 276 milligrams (mg) total fluorine per... packages shall not contain more than 120 mg total fluorine per package. (3) Exception. Package...

  16. 21 CFR 355.20 - Packaging conditions.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... (toothpastes and tooth powders) packages shall not contain more than 276 milligrams (mg) total fluorine per... packages shall not contain more than 120 mg total fluorine per package. (3) Exception. Package...

  17. 21 CFR 355.20 - Packaging conditions.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... (toothpastes and tooth powders) packages shall not contain more than 276 milligrams (mg) total fluorine per... packages shall not contain more than 120 mg total fluorine per package. (3) Exception. Package...

  18. Optimal segmentation and packaging process

    DOEpatents

    Kostelnik, Kevin M.; Meservey, Richard H.; Landon, Mark D.

    1999-01-01

    A process for improving packaging efficiency uses three dimensional, computer simulated models with various optimization algorithms to determine the optimal segmentation process and packaging configurations based on constraints including container limitations. The present invention is applied to a process for decontaminating, decommissioning (D&D), and remediating a nuclear facility involving the segmentation and packaging of contaminated items in waste containers in order to minimize the number of cuts, maximize packaging density, and reduce worker radiation exposure. A three-dimensional, computer simulated, facility model of the contaminated items are created. The contaminated items are differentiated. The optimal location, orientation and sequence of the segmentation and packaging of the contaminated items is determined using the simulated model, the algorithms, and various constraints including container limitations. The cut locations and orientations are transposed to the simulated model. The contaminated items are actually segmented and packaged. The segmentation and packaging may be simulated beforehand. In addition, the contaminated items may be cataloged and recorded.

  19. FABRICATION AND DEPLOYMENT OF THE 9979 TYPE AF RADIOACTIVE WASTE PACKAGING FOR THE DEPARTMENT OF ENERGY

    SciTech Connect

    Blanton, P.; Eberl, K.

    2013-10-10

    This paper summarizes the development, testing, and certification of the 9979 Type A Fissile Packaging that replaces the UN1A2 Specification Shipping Package eliminated from Department of Transportation (DOT) 49 CFR 173. The DOT Specification Package was used for many decades by the U.S. nuclear industry as a fissile waste container until its removal as an authorized container by DOT. This paper will discuss stream lining procurement of high volume radioactive material packaging manufacturing, such as the 9979, to minimize packaging production costs without sacrificing Quality Assurance. The authorized content envelope (combustible and non-combustible) as well as planned content envelope expansion will be discussed.

  20. The Kull IMC package

    SciTech Connect

    Gentile, N A; Keen,N; Rathkopf, J

    1998-10-01

    We describe the Kull IMC package, and Implicit Monte Carlo Program written for use in A and X division radiation hydro codes. The Kull IMC has been extensively tested. Written in C++ and using genericity via the template feature to allow easy integration into different codes, the Kull IMC currently runs coupled radiation hydrodynamic problems in 2 different 3D codes. A stand-alone version also exists, which has been parallelized with mesh replication. This version has been run on up to 384 processors on ASCI Blue Pacific.

  1. Safety Analysis Report for packaging (onsite) steel waste package

    SciTech Connect

    BOEHNKE, W.M.

    2000-07-13

    The steel waste package is used primarily for the shipment of remote-handled radioactive waste from the 324 Building to the 200 Area for interim storage. The steel waste package is authorized for shipment of transuranic isotopes. The maximum allowable radioactive material that is authorized is 500,000 Ci. This exceeds the highway route controlled quantity (3,000 A{sub 2}s) and is a type B packaging.

  2. Isolation and identification of bacteria from paperboard food packaging

    PubMed Central

    Mashhadi Mohammadzadeh-Vazifeh, Mojtaba; Khajeh-Nasiri, Shamsolmoluk; Hashemi, Shabnam; Fakhari, Javad

    2015-01-01

    Background and Objectives: Paper and paperboard packaging play an important role in safety and quality of food products. Common bacteria of paper and paperboard food packaging could grow due to specific conditions included humidity, temperature and major nutrition to contaminate the food. The purpose of this research was to investigate numbers and the types of bacteria in the food packaging paperboard. Materials and Methods: The surface and the depth of the each paperboard sample were examined by the dimension of one cm2 and one gram. The paperboard samples were randomly collected from popular confectionaries and fast food restaurants in Tehran, Iran. Results: The results indicated the range of 0.2×103 to >1.0×105 cfu/1g bacterial contamination in paperboard food packaging. Also, most detected bacteria were from spore forming and family Bacillaceae. Conclusion: The bioburden paperboard used for food packaging showed high contamination rate more than standard acceptance level. PMID:26719786

  3. Modular vaccine packaging increases packing efficiency

    PubMed Central

    Norman, Bryan A.; Rajgopal, Jayant; Lim, Jung; Gorham, Katrin; Haidari, Leila; Brown, Shawn T.; Lee, Bruce Y.

    2015-01-01

    Background Within a typical vaccine supply chain, vaccines are packaged into individual cylindrical vials (each containing one or more doses) that are bundled together in rectangular “inner packs” for transport via even larger groupings such as cold boxes and vaccine carriers. The variability of vaccine inner pack and vial size may hinder efficient vaccine distribution because it constrains packing of cold boxes and vaccine carriers to quantities that are often inappropriate or suboptimal in the context of country-specific vaccination guidelines. Methods We developed in Microsoft Excel (Microsoft Corp., Redmond, WA) a spreadsheet model that evaluated the impact of different packing schemes for the Benin routine regimen plus the introduction of the Rotarix vaccine. Specifically, we used the model to compare the current packing scheme to that of a proposed modular packing scheme. Results Conventional packing of a Dometic RCW25 that aims to maximize fully-immunized children (FICs) results in 123 FICs and a packing efficiency of 81.93% compared to a maximum of 155 FICs and 94.1% efficiency for an alternative modular packaging system. Conclusions Our analysis suggests that modular packaging systems could offer significant advantages over conventional vaccine packaging systems with respect to space efficiency and potential FICs, when they are stored in standard vaccine carrying devices. This allows for more vaccines to be stored within the same volume while also simplifying the procedures used by field workers to pack storage devices. Ultimately, modular packaging systems could be a simple way to help increase vaccine coverage worldwide. PMID:25957666

  4. Japan's electronic packaging technologies

    NASA Technical Reports Server (NTRS)

    Tummala, Rao R.; Pecht, Michael

    1995-01-01

    The JTEC panel found Japan to have significant leadership over the United States in the strategic area of electronic packaging. Many technologies and products once considered the 'heart and soul' of U.S. industry have been lost over the past decades to Japan and other Asian countries. The loss of consumer electronics technologies and products is the most notable of these losses, because electronics is the United States' largest employment sector and is critical for growth businesses in consumer products, computers, automobiles, aerospace, and telecommunications. In the past there was a distinction between consumer and industrial product technologies. While Japan concentrated on the consumer market, the United States dominated the industrial sector. No such distinction is anticipated in the future; the consumer-oriented technologies Japan has dominated are expected to characterize both domains. The future of U.S. competitiveness will, therefore, depend on the ability of the United States to rebuild its technological capabilities in the area of portable electronic packaging.

  5. CH Packaging Operations Manual

    SciTech Connect

    None, None

    2009-05-27

    This document provides the user with instructions for assembling a payload. All the steps in Subsections 1.2, Preparing 55-Gallon Drum Payload Assembly; 1.3, Preparing "Short" 85-Gallon Drum Payload Assembly (TRUPACT-II and HalfPACT); 1.4, Preparing "Tall" 85-Gallon Drum Payload Assembly (HalfPACT only); 1.5, Preparing 100-Gallon Drum Payload Assembly; 1.6, Preparing Shielded Container Payload Assembly; 1.7, Preparing SWB Payload Assembly; and 1.8, Preparing TDOP Payload Assembly, must be completed, but may be performed in any order as long as radiological control steps are not bypassed. Transport trailer operations, package loading and unloading from transport trailers, hoisting and rigging activities such as ACGLF operations, equipment checkout and shutdown, and component inspection activities must be performed, but may be performed in any order and in parallel with other activities as long as radiological control steps are not bypassed. Steps involving OCA/ICV lid removal/installation and payload removal/loading may be performed in parallel if there are multiple operators working on the same packaging. Steps involving removal/installation of OCV/ICV upper and lower main O-rings must be performed in sequence, except as noted.

  6. Tamper indicating packaging

    SciTech Connect

    Baumann, M.J.; Bartberger, J.C.; Welch, T.D.

    1994-08-01

    Protecting sensitive items from undetected tampering in an unattended environment is crucial to the success of non-proliferation efforts relying on the verification of critical activities. Tamper Indicating Packaging (TIP) technologies are applied to containers, packages, and equipment that require an indication of a tamper attempt. Examples include: the transportation and storage of nuclear material, the operation and shipment of surveillance equipment and monitoring sensors, and the retail storage of medicine and food products. The spectrum of adversarial tampering ranges from attempted concealment of a pin-hole sized penetration to the complete container replacement, which would involve counterfeiting efforts of various degrees. Sandia National Laboratories (SNL) has developed a technology base for advanced TIP materials, sensors, designs, and processes which can be adapted to various future monitoring systems. The purpose of this technology base is to investigate potential new technologies, and to perform basic research of advanced technologies. This paper will describe the theory of TIP technologies and recent investigations of TIP technologies at SNL.

  7. Japan's electronic packaging technologies

    NASA Astrophysics Data System (ADS)

    Tummala, Rao R.; Pecht, Michael

    1995-02-01

    The JTEC panel found Japan to have significant leadership over the United States in the strategic area of electronic packaging. Many technologies and products once considered the 'heart and soul' of U.S. industry have been lost over the past decades to Japan and other Asian countries. The loss of consumer electronics technologies and products is the most notable of these losses, because electronics is the United States' largest employment sector and is critical for growth businesses in consumer products, computers, automobiles, aerospace, and telecommunications. In the past there was a distinction between consumer and industrial product technologies. While Japan concentrated on the consumer market, the United States dominated the industrial sector. No such distinction is anticipated in the future; the consumer-oriented technologies Japan has dominated are expected to characterize both domains. The future of U.S. competitiveness will, therefore, depend on the ability of the United States to rebuild its technological capabilities in the area of portable electronic packaging.

  8. CH Packaging Operations Manual

    SciTech Connect

    None, None

    2008-09-11

    This document provides the user with instructions for assembling a payload. All the steps in Subsections 1.2, Preparing 55-Gallon Drum Payload Assembly; 1.3, Preparing "Short" 85-Gallon Drum Payload Assembly (TRUPACT-II and HalfPACT); 1.4, Preparing "Tall" 85-gallon Drum Payload Assembly (HalfPACT only); 1.5, Preparing 100-Gallon Drum Payload Assembly; 1.6, Preparing SWB Payload Assembly; and 1.7, Preparing TDOP Payload Assembly, must be completed, but may be performed in any order as long as radiological control steps are not bypassed. Transport trailer operations, package loading and unloading from transport trailers, hoisting and rigging activities such as ACGLF operations, equipment checkout and shutdown, and component inspection activities must be performed, but may be performed in any order and in parallel with other activities as long as radiological control steps are not bypassed. Steps involving OCA/ICV lid removal/installation and payload removal/loading may be performed in parallel if there are multiple operators working on the same packaging. Steps involving removal/installation of OCV/ICV upper and lower main O-rings must be performed in sequence.

  9. Food choice: the battle between package, taste and consumption situation.

    PubMed

    Gutjar, Swetlana; de Graaf, Cees; Palascha, Aikaterini; Jager, Gerry

    2014-09-01

    The present study compared how intrinsic (sensory) and extrinsic (packaging) product properties influence actual food choice in combination with the concept of product appropriateness in a specific consumption context. Food choice of seven test products was measured in three breakfast sessions within a simulated cafeteria setting with subsequent product consumption. Test products were five breakfast drinks and two dessert products considered as inappropriate for breakfast. One hundred and three participants took part in a blind taste session, after which they chose one out of the seven foods to consume for breakfast. In a second session (familiar package session), the same participants based their choice on the package of the seven foods they tasted in the first session. An additional group of 65 participants took part in a third naïve package session, where they chose just on the basis of package without being previously exposed to the foods. Results showed that food choices in the naïve package session were guided by the package that labelled the products as "breakfast product". Food choices in the blind session were strongly correlated (r = 0.8) with the liking of the products. Food choice in the "familiar package session" lay between the blind and naïve package session. It is concluded that food choice in a simulated cafeteria setting is guided by extrinsic (package) as well as intrinsic (sensory) properties and both can act as a cue for product appropriateness given a specific consumption context. Depending on the salience of either intrinsic or extrinsic properties during the choice moment their impact on choice is stronger. PMID:24845783

  10. Space station power semiconductor package

    NASA Technical Reports Server (NTRS)

    Balodis, Vilnis; Berman, Albert; Devance, Darrell; Ludlow, Gerry; Wagner, Lee

    1987-01-01

    A package of high-power switching semiconductors for the space station have been designed and fabricated. The package includes a high-voltage (600 volts) high current (50 amps) NPN Fast Switching Power Transistor and a high-voltage (1200 volts), high-current (50 amps) Fast Recovery Diode. The package features an isolated collector for the transistors and an isolated anode for the diode. Beryllia is used as the isolation material resulting in a thermal resistance for both devices of .2 degrees per watt. Additional features include a hermetical seal for long life -- greater than 10 years in a space environment. Also, the package design resulted in a low electrical energy loss with the reduction of eddy currents, stray inductances, circuit inductance, and capacitance. The required package design and device parameters have been achieved. Test results for the transistor and diode utilizing the space station package is given.

  11. Module 13: Bulk Packaging Shipments by Highway

    SciTech Connect

    Przybylski, J.L.

    1994-07-01

    The Hazardous Materials Modular Training Program provides participating United States Department of Energy (DOE) sites with a basic, yet comprehensive, hazardous materials transportation training program for use onsite. This program may be used to assist individual program entities to satisfy the general awareness, safety training, and function specific training requirements addressed in Code of Federal Regulation (CFR), Title 49, Part 172, Subpart H -- ``Training.`` Module 13 -- Bulk Packaging Shipments by Highway is a supplement to the Basic Hazardous Materials Workshop. Module 13 -- Bulk Packaging Shipments by Highway focuses on bulk shipments of hazardous materials by highway mode, which have additional or unique requirements beyond those addressed in the ten module core program. Attendance in this course of instruction should be limited to those individuals with work experience in transporting hazardous materials utilizing bulk packagings and who have completed the Basic Hazardous Materials Workshop or an equivalent. Participants will become familiar with the rules and regulations governing the transportation by highway of hazardous materials in bulk packagings and will demonstrate the application of these requirements through work projects and examination.

  12. Packaging investigation of optoelectronic devices

    NASA Astrophysics Data System (ADS)

    Zhike, Zhang; Yu, Liu; Jianguo, Liu; Ninghua, Zhu

    2015-10-01

    Compared with microelectronic packaging, optoelectronic packaging as a new packaging type has been developed rapidly and it will play an essential role in optical communication. In this paper, we try to summarize the development history, research status, technology issues and future prospects, and hope to provide a meaningful reference. Project supported by the National High Technology Research and Development Program of China (Nos. 2013AA014201, 2013AA014203) and the National Natural Science Foundation of China (Nos. 61177080, 61335004, 61275031).

  13. IN-PACKAGE CHEMISTRY ABSTRACTION

    SciTech Connect

    E. Thomas

    2005-07-14

    This report was developed in accordance with the requirements in ''Technical Work Plan for Postclosure Waste Form Modeling'' (BSC 2005 [DIRS 173246]). The purpose of the in-package chemistry model is to predict the bulk chemistry inside of a breached waste package and to provide simplified expressions of that chemistry as a function of time after breach to Total Systems Performance Assessment for the License Application (TSPA-LA). The scope of this report is to describe the development and validation of the in-package chemistry model. The in-package model is a combination of two models, a batch reactor model, which uses the EQ3/6 geochemistry-modeling tool, and a surface complexation model, which is applied to the results of the batch reactor model. The batch reactor model considers chemical interactions of water with the waste package materials, and the waste form for commercial spent nuclear fuel (CSNF) waste packages and codisposed (CDSP) waste packages containing high-level waste glass (HLWG) and DOE spent fuel. The surface complexation model includes the impact of fluid-surface interactions (i.e., surface complexation) on the resulting fluid composition. The model examines two types of water influx: (1) the condensation of water vapor diffusing into the waste package, and (2) seepage water entering the waste package as a liquid from the drift. (1) Vapor-Influx Case: The condensation of vapor onto the waste package internals is simulated as pure H{sub 2}O and enters at a rate determined by the water vapor pressure for representative temperature and relative humidity conditions. (2) Liquid-Influx Case: The water entering a waste package from the drift is simulated as typical groundwater and enters at a rate determined by the amount of seepage available to flow through openings in a breached waste package.

  14. Development of an Air Transport Type A Fissile Package

    SciTech Connect

    Blanton, P.; Ebert, K.

    2011-07-13

    This paper presents the summary of testing by the Savannah River National Laboratory (SRNL) to support development of a light weight (<140 lbs) air transport qualified Type A Fissile Packaging. The package design incorporates features and materials specifically designed to minimize packaging weight. The light weight package is being designed to provide confinement to the contents when subjected to the normal and hypothetical conditions required of an air transportable Type A Fissile radioactive material shipping package. The objective of these tests was to provide design input to the final design for the LORX Type A Fissile Air Transport Packaging when subjected to the performance requirements of the drop, crush and puncture probe test of 10CFR71. The post test evaluation of the prototype packages indicates that all of the tested designs would satisfactorily confine the content within the packaging. The differences in the performance of the prototypes varied significantly depending on the core materials and their relative densities. Information gathered from these tests is being used to develop the final design for the Department of Homeland Security.

  15. Corrosion model validation in high level nuclear package research

    SciTech Connect

    McNeil, M.B.; Moody, J.B.

    1993-12-31

    The strategies for waste package (WP) performance validation will be based on site specific geologic and hydrogeochemical information plus models which can be used to predict potential WP lifetimes. The development and application of such models will include the evaluation of natural analogues (NA). These analogues are needed to resolve issues related to the validation of models. Natural analogues have not had extensive use or widespread acceptance in the area of waste package failure prediction. This lack of acceptance is due to the anticipated choice of alloys for waste package containers. Few of these alloys are similar to naturally occurring metals, and the proposed HLW repositories are in general in geologic settings not very similar to those in which naturally occurring metals are generally found. Natural and archaeological analogues can be used, however, in analysis of possible waste package failures as a means of testing proposed models for failure. In fact, the analogues are the only available mechanisms for testing models of long-term waste package behavior. A strategy is outlined for incorporating natural and archaeological analogue studies into waste package research, and examples are discussed. The natural/archaeological analogous approach which appears most promising is to use archaeological and mineral samples to develop an understanding of the identities and rates of the mineral alteration reactions at or near the surface of the package, improving present capability for estimating the lifetimes of metallic waste package containers.

  16. About the ZOOM minimization package

    SciTech Connect

    Fischler, M.; Sachs, D.; /Fermilab

    2004-11-01

    A new object-oriented Minimization package is available for distribution in the same manner as CLHEP. This package, designed for use in HEP applications, has all the capabilities of Minuit, but is a re-write from scratch, adhering to modern C++ design principles. A primary goal of this package is extensibility in several directions, so that its capabilities can be kept fresh with as little maintenance effort as possible. This package is distinguished by the priority that was assigned to C++ design issues, and the focus on producing an extensible system that will resist becoming obsolete.

  17. Naval Waste Package Design Report

    SciTech Connect

    M.M. Lewis

    2004-03-15

    A design methodology for the waste packages and ancillary components, viz., the emplacement pallets and drip shields, has been developed to provide designs that satisfy the safety and operational requirements of the Yucca Mountain Project. This methodology is described in the ''Waste Package Design Methodology Report'' Mecham 2004 [DIRS 166168]. To demonstrate the practicability of this design methodology, four waste package design configurations have been selected to illustrate the application of the methodology. These four design configurations are the 21-pressurized water reactor (PWR) Absorber Plate waste package, the 44-boiling water reactor (BWR) waste package, the 5-defense high-level waste (DHLW)/United States (U.S.) Department of Energy (DOE) spent nuclear fuel (SNF) Co-disposal Short waste package, and the Naval Canistered SNF Long waste package. Also included in this demonstration is the emplacement pallet and continuous drip shield. The purpose of this report is to document how that design methodology has been applied to the waste package design configurations intended to accommodate naval canistered SNF. This demonstrates that the design methodology can be applied successfully to this waste package design configuration and support the License Application for construction of the repository.

  18. Anhydrous Ammonia Training Module. Trainer's Package. Participant's Package.

    ERIC Educational Resources Information Center

    Beaudin, Bart; And Others

    This document contains a trainer's and a participant's package for teaching employees on site safe handling procedures for working with anhydrous ammonia, especially on farms. The trainer's package includes the following: a description of the module; a competency; objectives; suggested instructional aids; a training outline (or lesson plan) for…

  19. Packaging Design Criteria for the Steel Waste Package

    SciTech Connect

    BOEHNKE, W.M.

    2000-10-19

    This packaging design criteria provides the criteria for the design, fabrication, safety evaluation, and use of the steel waste package (SWP) to transport remote-handled waste and special-case waste from the 324 facility to Central Waste Complex (CWC) for interim storage.

  20. Package Up Your Troubles--An Introduction to Package Libraries

    ERIC Educational Resources Information Center

    Frank, Colin

    1978-01-01

    Discusses a "package deal" library--a prefabricated building including interior furnishing--in terms of costs, fitness for purpose, and interior design, i.e., shelving, flooring, heating, lighting, and humidity. Advantages and disadvantages of the package library are also considered. (Author/MBR)

  1. Technical Review Report for the Mound 1KW Package Safety Analysis Report for Packaging Addendum No. 1, through Revision b

    SciTech Connect

    DiSabatino, A; West, M; Hafner, R; Russell, E

    2007-10-04

    This Technical Review Report (TRR) documents the review, performed by the Lawrence Livermore National Laboratory (LLNL) staff, at the request of the U.S. Department of Energy (DOE), on the 'Mound 1KW Package Safety Analysis Report for Packaging, Addendum No. 1, Revision b', dated May 2007 (Addendum 1). The Mound 1KW Package is certified by DOE Certificate of Compliance (CoC) number USA/9516/B(U)F-85 for the transportation of Type B quantities of plutonium heat source material. The safety analysis of the package is documented in the 'Safety Analysis Report for Packaging (SARP) for the Mound 1KW Package' (i.e., the Mound 1KW SARP, or the SARP). Addendum 1 incorporates a new fueled capsule assembly payload. The following changes have been made to add this payload: (1) The primary containment vessel (PCV) will be of the same design, but will increase in height to 11.16 in.; (2) A new graphite support block will be added to support up to three fueled capsule assemblies per package; (3) The cutting groove height on the secondary containment vessel (SCV) will be heightened to accommodate the taller PCV; and (4) A 3.38 in. high graphite filler block will be placed on top of the PCV. All other packaging features, as described in the Mound 1KW SARP [3], remain unchanged. This report documents the LLNL review of Addendum 1[1]. The specific review for each SARP Chapter is documented herein.

  2. Intelligent Design of Vehicle Package Using Ontology and Casebased Reasoning

    NASA Astrophysics Data System (ADS)

    Jin, Xiaoping; Mao, Enrong; Cheng, Bo

    The similarity of varied vehicle package is a critical design feature that affects method selection, optimized design and driver performance. However there is limited understanding of what constitutes similarity in package design and limited computer-based support to identify this feature in a layout model. This paper contributes a case-based framework for representing and reasoning about layout similarity that builds on domain-specific ontological modeling and case-based reasoning techniques. Validation study of the system provides evidence that the framework is general and enables a more efficient package layout design process.

  3. Hydropower computerized reconnaissance package, version 2.0

    NASA Astrophysics Data System (ADS)

    Broadus, C. R.

    1981-04-01

    The package is a computerized preliminary engineering and economic study package for small hydroelectric projects which consists of three programs. One engineering program evaluates the flow characteristics of a site and determines the energy generated for various turbine configurations and two economic programs provide two levels of economic studies depending upon the amount of site-specific information available. An Apple II computer is utilized to provide a quick-turnaround capability. The models and methods used in the HCR package are described and information is provided on program application, sample run sessions, program outputs, and listings of the main programs.

  4. Technology transfer package on seismic base isolation - Volume III

    SciTech Connect

    1995-02-14

    This Technology Transfer Package provides some detailed information for the U.S. Department of Energy (DOE) and its contractors about seismic base isolation. Intended users of this three-volume package are DOE Design and Safety Engineers as well as DOE Facility Managers who are responsible for reducing the effects of natural phenomena hazards (NPH), specifically earthquakes, on their facilities. The package was developed as part of DOE's efforts to study and implement techniques for protecting lives and property from the effects of natural phenomena and to support the International Decade for Natural Disaster Reduction. Volume III contains supporting materials not included in Volumes I and II.

  5. Extending the utility of a radioactive material package

    SciTech Connect

    Abramczyk, G.; Nathan, S.; Loftin, B.; Bellamy, S.

    2015-06-04

    Once a package has been certified for the transportation of DOT Hazard Class 7 – Radioactive Material in compliance with the requirements of 10 CFR 71, it is often most economical to extend its utility through the addition of content-specific configuration control features or the addition of shielding materials. The SRNL Model 9977 Package’s authorization was expanded from its original single to twenty contents in this manner; and most recently, the 9977 was evaluated for a high-gamma source content. This paper discusses the need for and the proposed shielding modifications to the package for extending the utility of the package for this purpose.

  6. Piecewise Cubic Interpolation Package

    1982-04-23

    PCHIP (Piecewise Cubic Interpolation Package) is a set of subroutines for piecewise cubic Hermite interpolation of data. It features software to produce a monotone and "visually pleasing" interpolant to monotone data. Such an interpolant may be more reasonable than a cubic spline if the data contain both 'steep' and 'flat' sections. Interpolation of cumulative probability distribution functions is another application. In PCHIP, all piecewise cubic functions are represented in cubic Hermite form; that is, f(x)more » is determined by its values f(i) and derivatives d(i) at the breakpoints x(i), i=1(1)N. PCHIP contains three routines - PCHIM, PCHIC, and PCHSP to determine derivative values, six routines - CHFEV, PCHFE, CHFDV, PCHFD, PCHID, and PCHIA to evaluate, differentiate, or integrate the resulting cubic Hermite function, and one routine to check for monotonicity. A FORTRAN 77 version and SLATEC version of PCHIP are included.« less

  7. Thyra Abstract Interface Package

    2005-09-01

    Thrya primarily defines a set of abstract C++ class interfaces needed for the development of abstract numerical atgorithms (ANAs) such as iterative linear solvers, transient solvers all the way up to optimization. At the foundation of these interfaces are abstract C++ classes for vectors, vector spaces, linear operators and multi-vectors. Also included in the Thyra package is C++ code for creating concrete vector, vector space, linear operator, and multi-vector subclasses as well as other utilitiesmore » to aid in the development of ANAs. Currently, very general and efficient concrete subclass implementations exist for serial and SPMD in-core vectors and multi-vectors. Code also currently exists for testing objects and providing composite objects such as product vectors.« less

  8. Meros Preconditioner Package

    2004-04-01

    Meros uses the compositional, aggregation, and overload operator capabilities of TSF to provide an object-oriented package providing segregated/block preconditioners for linear systems related to fully-coupled Navier-Stokes problems. This class of preconditioners exploits the special properties of these problems to segregate the equations and use multi-level preconditioners (through ML) on the matrix sub-blocks. Several preconditioners are provided, including the Fp and BFB preconditioners of Kay & Loghin and Silvester, Elman, Kay & Wathen. The overall performancemore » and scalability of these preconditioners approaches that of multigrid for certain types of problems. Meros also provides more traditional pressure projection methods including SIMPLE and SIMPLEC.« less

  9. Tritium waste package

    DOEpatents

    Rossmassler, R.; Ciebiera, L.; Tulipano, F.J.; Vinson, S.; Walters, R.T.

    1995-11-07

    A containment and waste package system for processing and shipping tritium oxide waste received from a process gas includes an outer drum and an inner drum containing a disposable molecular sieve bed (DMSB) seated within the outer drum. The DMSB includes an inlet diffuser assembly, an outlet diffuser assembly, and a hydrogen catalytic recombiner. The DMSB absorbs tritium oxide from the process gas and converts it to a solid form so that the tritium is contained during shipment to a disposal site. The DMSB is filled with type 4A molecular sieve pellets capable of adsorbing up to 1000 curies of tritium. The recombiner contains a sufficient amount of catalyst to cause any hydrogen and oxygen present in the process gas to recombine to form water vapor, which is then adsorbed onto the DMSB. 1 fig.

  10. Pliris Solver Package

    SciTech Connect

    Kotulski, Joseph D.; Womble, David E.; Greenberg, David; Driessen, Brian

    2004-03-01

    PLIRIS is an object-oriented solver built on top of a previous matrix solver used in a number of application codes. Puns solves a linear system directly via LU factorization with partial pivoting. The user provides the linear system in terms of Epetra Objects including a matrix and right-hand-sides. The user can then factor the matrix and perform the forward and back solve at a later time or solve for multiple right-hand-sides at once. This package is used when dense matrices are obtained in the problem formulation. These dense matrices occur whenever boundary element techniques are chosen for the solution procedure. This has been used in electromagnetics for both static and frequency domain problems.

  11. The LISA Technology Package

    NASA Technical Reports Server (NTRS)

    Livas, Jeff

    2009-01-01

    The LISA Technology Package (LTP) is the payload of the European Space Agency's LISA Pathfinder mission. LISA Pathfinder was instigated to test, in a flight environment, the critical technologies required by LISA; namely, the inertial sensing subsystem and associated control laws and micro-Newton thrusters required to place a macroscopic test mass in pure free-fall. The UP is in the late stages of development -- all subsystems are currently either in the final stages of manufacture or in test. Available flight units are being integrated into the real-time testbeds for system verification tests. This poster will describe the UP and its subsystems, give the current status of the hardware and test campaign, and outline the future milestones leading to the UP delivery.

  12. Tritium waste package

    DOEpatents

    Rossmassler, Rich; Ciebiera, Lloyd; Tulipano, Francis J.; Vinson, Sylvester; Walters, R. Thomas

    1995-01-01

    A containment and waste package system for processing and shipping tritium xide waste received from a process gas includes an outer drum and an inner drum containing a disposable molecular sieve bed (DMSB) seated within outer drum. The DMSB includes an inlet diffuser assembly, an outlet diffuser assembly, and a hydrogen catalytic recombiner. The DMSB absorbs tritium oxide from the process gas and converts it to a solid form so that the tritium is contained during shipment to a disposal site. The DMSB is filled with type 4A molecular sieve pellets capable of adsorbing up to 1000 curies of tritium. The recombiner contains a sufficient amount of catalyst to cause any hydrogen add oxygen present in the process gas to recombine to form water vapor, which is then adsorbed onto the DMSB.

  13. Tpetra Kernel Package

    2004-03-01

    A package of classes for constructing and using distributed sparse and dense matrices, vectors and graphs. Templated on the scalar and ordinal types so that any valid floating-point type, as well as any valid integer type can be used with these classes. Other non-standard types, such as 3-by-3 matrices for the scalar type and mod-based integers for ordinal types, can also be used. Tpetra is intended to provide the foundation for basic matrix and vectormore » operations for the next generation of Trilinos preconditioners and solvers, It can be considered as the follow-on to Epetra. Tpetra provides distributed memory operations via an abstract parallel machine interface, The most common implementation of this interface will be MPI.« less

  14. The LISA Technology Package

    NASA Astrophysics Data System (ADS)

    Livas, Jeffrey C.; LISA Pathfinder Science Working Team

    2010-01-01

    The LISA Technology Package (LTP) is the payload of the European Space Agency's LISA Pathfinder mission. LISA Pathfinder was instigated to test, in a flight environment, the critical technologies required by LISA; namely, the inertial sensing subsystem and associated control laws and micro-Newton thrusters required to place a macroscopic test mass in pure free-fall. The LTP is in the late stages of development - all subsystems are currently either in the final stages of manufacture or in test. Available flight units are being integrated into the real-time testbeds for system verification tests. This poster will describe the LTP and its subsystems, give the current status of the hardware and test campaign, and outline the future milestones leading to the LTP delivery.

  15. The LISA Technology Package

    NASA Astrophysics Data System (ADS)

    McNamara, Paul

    The LISA Technology Package (LTP) is the payload of the European Space Agency's LISA Pathfinder mission. LISA Pathfinder was instigated to test, in a flight environment, the critical technologies required by LISA; namely, the inertial sensing subsystem and associated control laws and micro-Newton thrusters required to place a macroscopic test mass in pure free-fall. The LTP is in the late stages of development -all subsystems are currently either in the final stages of manufacture or in test. Available flight units are being integrated into the real-time testbeds for system verification tests. This poster will describe the LTP and its subsystems, give the current status of the hardware and test campaigns, and outline the future milestones leading to the LTP delivery.

  16. Anasazi Block Eigensolvers Package

    2004-03-01

    ANASAZI is an extensible and interoperable framework for large-scale eigenvalue algorithms. The motivation for this framework is to provide a generic interface to a collection of algorithms for solving large-scale eigenvalue problems. ANASAZI is interoperable because both the matrix and vectors (defining the eigenspace) are considered to be opaque objects---only knowledge of the matrix and vectors via elementary operations is necessary. An implementation of Anasazi is accomplished via the use of interfaces. One of themore » goals of ANASAZI is to allow the user the flexibility to specify the data representation for the matrix and vectors and so leverage any existing software investment. The algorithms that will be included in package are Krylov-based and preconditioned eigensolvers.« less

  17. Waste package environment studies. FY 1984 annual report.

    SciTech Connect

    Pederson, L.R.; Gray, W.J.; Hodges, F.N.; McVay, G.L.; Moore, D.A.; Rai, D.; Schramke, J.A.

    1986-03-01

    Tests were conducted by Pacific Northwest Laboratory in FY 1984 to examine the influence of heat and radiation on the chemical environment of a high-level nuclear waste package in a repository in salt and to determine the solubility of key radionuclides in site-specific brines. These tests are part of an ongoing effort by the Waste Package Program, whose objective is to help develop a data base on package components and system interactions necessary to qualify a nuclear waste package for geologic disposal. Specifically, tests performed in FY 1984 involved alpha and gamma radiolysis of brines, americium solubility in brines, the influence of heat and radiation on rock salt, and the influence of temperature on brine chemistry.

  18. DOT-7A Type A packaging design guide

    SciTech Connect

    Kelly, D.L.

    1995-01-23

    The purpose of this Design Guide is to provide instruction for designing a U.S. Department of Transportation Specification 7A (DOT-7A) Type A packaging. Another purpose for this Design Guide is to support the evaluation and testing activities that are performed on new designs by a U.S. Department of Energy (DOE) test facility. This evaluation and testing program is called the DOT-7A Program. When an applicant has determined that a DOT-7A packaging is needed and not commercially available, a design may be created according to this document. The design should include a packaging drawing, specifications, analysis report, operating instructions, and a Packaging Qualification Checklist; all of which should be forwarded to a DOE/HQ approved test facility for evaluation and testing. This report is being submitted through the Engineering Documentation System so that it may be used for reference and information purposes.

  19. Chip packaging technique

    NASA Technical Reports Server (NTRS)

    Jayaraj, Kumaraswamy (Inventor); Noll, Thomas E. (Inventor); Lockwood, Harry F. (Inventor)

    2001-01-01

    A hermetically sealed package for at least one semiconductor chip is provided which is formed of a substrate having electrical interconnects thereon to which the semiconductor chips are selectively bonded, and a lid which preferably functions as a heat sink, with a hermetic seal being formed around the chips between the substrate and the heat sink. The substrate is either formed of or includes a layer of a thermoplastic material having low moisture permeability which material is preferably a liquid crystal polymer (LCP) and is a multiaxially oriented LCP material for preferred embodiments. Where the lid is a heat sink, the heat sink is formed of a material having high thermal conductivity and preferably a coefficient of thermal expansion which substantially matches that of the chip. A hermetic bond is formed between the side of each chip opposite that connected to the substrate and the heat sink. The thermal bond between the substrate and the lid/heat sink may be a pinched seal or may be provided, for example by an LCP frame which is hermetically bonded or sealed on one side to the substrate and on the other side to the lid/heat sink. The chips may operate in the RF or microwave bands with suitable interconnects on the substrate and the chips may also include optical components with optical fibers being sealed into the substrate and aligned with corresponding optical components to transmit light in at least one direction. A plurality of packages may be physically and electrically connected together in a stack to form a 3D array.

  20. Electro-Microfluidic Packaging

    SciTech Connect

    BENAVIDES, GILBERT L.; GALAMBOS, PAUL C.

    2002-06-01

    Electro-microfluidics is experiencing explosive growth in new product developments. There are many commercial applications for electro-microfluidic devices such as chemical sensors, biological sensors, and drop ejectors for both printing and chemical analysis. The number of silicon surface micromachined electro-microfluidic products is likely to increase. Manufacturing efficiency and integration of microfluidics with electronics will become important. Surface micromachined microfluidic devices are manufactured with the same tools as IC's (integrated circuits) and their fabrication can be incorporated into the IC fabrication process. In order to realize applications for devices must be developed. An Electro-Microfluidic Dual In-line Package (EMDIP{trademark}) was developed surface micromachined electro-microfluidic devices, a practical method for getting fluid into these to be a standard solution that allows for both the electrical and the fluidic connections needed to operate a great variety of electro-microfluidic devices. The EMDIP{trademark} includes a fan-out manifold that, on one side, mates directly with the 200 micron diameter Bosch etched holes found on the device, and, on the other side, mates to lager 1 mm diameter holes. To minimize cost the EMDIP{trademark} can be injection molded in a great variety of thermoplastics which also serve to optimize fluid compatibility. The EMDIP{trademark} plugs directly into a fluidic printed wiring board using a standard dual in-line package pattern for the electrical connections and having a grid of multiple 1 mm diameter fluidic connections to mate to the underside of the EMDIP{trademark}.

  1. 44-BWR WASTE PACKAGE LOADING CURVE EVALUATION

    SciTech Connect

    J.M. Scaglione

    2004-08-25

    The objective of this calculation is to evaluate the required minimum burnup as a function of initial boiling water reactor (BWR) assembly enrichment that would permit loading of spent nuclear fuel into the 44 BWR waste package configuration as provided in Attachment IV. This calculation is an application of the methodology presented in ''Disposal Criticality Analysis Methodology Topical Report'' (YMP 2003). The scope of this calculation covers a range of enrichments from 0 through 5.0 weight percent (wt%) U-235, and a burnup range of 0 through 40 GWd/MTU. This activity supports the validation of the use of burnup credit for commercial spent nuclear fuel applications. The intended use of these results will be in establishing BWR waste package configuration loading specifications. Limitations of this evaluation are as follows: (1) The results are based on burnup credit for actinides and selected fission products as proposed in YMP (2003, Table 3-1) and referred to as the ''Principal Isotopes''. Any change to the isotope listing will have a direct impact on the results of this report. (2) The results of 100 percent of the current BWR projected waste stream being able to be disposed of in the 44-BWR waste package with Ni-Gd Alloy absorber plates is contingent upon the referenced waste stream being sufficiently similar to the waste stream received for disposal. (3) The results are based on 1.5 wt% Gd in the Ni-Gd Alloy material and having no tuff inside the waste package. If the Gd loading is reduced or a process to introduce tuff inside the waste package is defined, then this report would need to be reevaluated based on the alternative materials.

  2. A Method for Determining Optimal Residential Energy Efficiency Packages

    SciTech Connect

    Polly, B.; Gestwick, M.; Bianchi, M.; Anderson, R.; Horowitz, S.; Christensen, C.; Judkoff, R.

    2011-04-01

    This report describes an analysis method for determining optimal residential energy efficiency retrofit packages and, as an illustrative example, applies the analysis method to a 1960s-era home in eight U.S. cities covering a range of International Energy Conservation Code (IECC) climate regions. The method uses an optimization scheme that considers average energy use (determined from building energy simulations) and equivalent annual cost to recommend optimal retrofit packages specific to the building, occupants, and location.

  3. Tracheal overexpression of IL-1β, IRAK-1 and TRAF-6 mRNA in obese-asthmatic male Wistar rats

    PubMed Central

    Aslani, Mohammad Reza; Keyhanmanesh, Rana; Khamaneh, Amir Mehdi; Abbasi, Mehran Mesgari; Fallahi, Maryam; Alipour, Mohammad Reza

    2016-01-01

    Objective(s): Human and animal studies have shown a close relationship between obesity and asthma severity. Here, we examined the effects of diet-induced obesity (DIO) on the expression levels of IL-1β, IRAK-1 and TRAF-6 mRNA in male Wistar rats tracheal after sensitization with ovalbumin (OVA). Materials and Methods: Twenty male Wistar rats divided to four groups, included, control group with normal diet (C+ND), OVA-sensitized group with normal diet (S+ND), control group with high-fat diet (C+HFD), and OVA-sensitized group with high-fat diet (S+HFD). All animals fed for 8 weeks with standard pelts or high-fat diet, and then were sensitized and challenged with OVA or saline for another 4 weeks with designed regimens. At the end of study, trachea isolated and examined for expression levels of IL-1β, IRAK-1 and TRAF-6 mRNA with RT-PCR method. Results: Diet-induced obesity groups developed increased weight, obesity indexes and lipid profiles (P<0.05 to P<0.001). The expression levels of IL-1β mRNA in OVA-sensitization groups (S+ND and S+HFD) showed a significantly increased when compared with control group. Also in S+HFD group, expression level of TRAF-6 mRNA was higher than other groups (P<0.001). IRAK-1 expression level was high in S+HFD compared with control group.IL-1β and TRAF-6 mRNA correlated positively with obesity indexes. Conclusion: The results showed that DIO causes overexpression of IL-1β, IRAK-1 and TRAF-6 mRNA in an experimental model of asthma. Our results suggested that in obese-asthmatic conditions locally production and activation of pro-inflammatory agents can be increased. These findings showed that possible mechanism for obesity-asthma relationships. PMID:27279977

  4. DEVELOPMENT OF A NEW TYPE A(F)RADIOACTIVE MATERIAL PACKAGING FOR THE DEPARTMENT OF ENERGY

    SciTech Connect

    Blanton, P.; Eberl, K.

    2008-09-14

    In a coordinated effort, the Department of Transportation (DOT) and Nuclear Regulatory Commission (NRC) proposed the elimination of the Specification Packaging from 49 CFR 173.[1] In accordance with the Federal Register, issued on October 1, 2004, new fabrication of Specification Packages would no longer be authorized. In accordance with the NRC final rulemaking published January 26, 2004, Specification Packagings are mandated by law to be removed from service no later than October 1, 2008. This coordinated effort and resulting rulemaking initiated a planned phase out of Specification Type B and Type A fissile (F) material transportation packages within the Department of Energy (DOE) and its subcontractors. One of the Specification Packages affected by this regulatory change is the UN1A2 Specification Package, per DOT 49 CFR 173.417(a)(6). To maintain continuing shipments of DOE materials currently transported in UN1A2 Specification Package after the existing authorization expires, a replacement Type A(F) material packaging design is under development by the Savannah River National Laboratory. This paper presents a summary of the prototype design effort and testing of the new Type A(F) Package development for the DOE. This paper discusses the progress made in the development of a Type A Fissile Packaging to replace the expiring 49 CFR UN1A2 Specification Fissile Package. The Specification Package was mostly a single-use waste disposal container. The design requirements and authorized radioactive material contents of the UN1A2 Specification Package were defined in 49 CFR. A UN1A2 Specification Package was authorized to ship up to 350 grams of U-235 in any enrichment and in any non-pyrophoric form. The design was specified as a 55-gallon 1A2 drum overpack with a body constructed from 18 gauge steel with a 16 gauge drum lid. Drum closure was specified as a standard 12-gauge ring closure. The inner product container size was not specified but was listed as any

  5. The Macro - TIPS Course Package.

    ERIC Educational Resources Information Center

    Heriot-Watt Univ., Edinburgh (Scotland). Esmee Fairbairn Economics Research Centre.

    The TIPS (Teaching Information Processing System) Course Package was designed to be used with the Macro-Games Course Package (SO 011 930) in order to train college students to apply the tools of economic analysis to current problems. TIPS is used to provide feedback and individualized assignments to students, as well as information about the…

  6. Solar water heater design package

    NASA Technical Reports Server (NTRS)

    1981-01-01

    Package describes commercial domestic-hot-water heater with roof or rack mounted solar collectors. System is adjustable to pre-existing gas or electric hot-water house units. Design package includes drawings, description of automatic control logic, evaluation measurements, possible design variations, list of materials and installation tools, and trouble-shooting guide and manual.

  7. Packaging Software Assets for Reuse

    NASA Astrophysics Data System (ADS)

    Mattmann, C. A.; Marshall, J. J.; Downs, R. R.

    2010-12-01

    The reuse of existing software assets such as code, architecture, libraries, and modules in current software and systems development projects can provide many benefits, including reduced costs, in time and effort, and increased reliability. Many reusable assets are currently available in various online catalogs and repositories, usually broken down by disciplines such as programming language (Ibiblio for Maven/Java developers, PyPI for Python developers, CPAN for Perl developers, etc.). The way these assets are packaged for distribution can play a role in their reuse - an asset that is packaged simply and logically is typically easier to understand, install, and use, thereby increasing its reusability. A well-packaged asset has advantages in being more reusable and thus more likely to provide benefits through its reuse. This presentation will discuss various aspects of software asset packaging and how they can affect the reusability of the assets. The characteristics of well-packaged software will be described. A software packaging domain model will be introduced, and some existing packaging approaches examined. An example case study of a Reuse Enablement System (RES), currently being created by near-term Earth science decadal survey missions, will provide information about the use of the domain model. Awareness of these factors will help software developers package their reusable assets so that they can provide the most benefits for software reuse.

  8. Chemical Energy: A Learning Package.

    ERIC Educational Resources Information Center

    Cohen, Ita; Ben-Zvi, Ruth

    1982-01-01

    A comprehensive teaching/learning chemical energy package was developed to overcome conceptual/experimental difficulties and time required for calculation of enthalpy changes. The package consists of five types of activities occuring in repeated cycles: group activities, laboratory experiments, inquiry questionnaires, teacher-led class…

  9. Status of PERST-5 package

    SciTech Connect

    Gomin, E. A.; Gurevich, M. I.; Kalugin, M. A.; Lazarenko, A. P.; Pryanichnikov, A. V. Sidorenko, V. D.; Druzhinin, V. E.; Zhirnov, A. P.; Rozhdestvenskiy, I. M.

    2012-12-15

    The methods and algorithms used in the PERST-5 package are described. This package is part of the MCU-5 code and is intended for neutron-physical calculation of the cells and parts of nuclear reactors using a generalized method of first collision probabilities.

  10. Status of PERST-5 package

    NASA Astrophysics Data System (ADS)

    Gomin, E. A.; Gurevich, M. I.; Kalugin, M. A.; Lazarenko, A. P.; Pryanichnikov, A. V.; Sidorenko, V. D.; Druzhinin, V. E.; Zhirnov, A. P.; Rozhdestvenskiy, I. M.

    2012-12-01

    The methods and algorithms used in the PERST-5 package are described. This package is part of the MCU-5 code and is intended for neutron-physical calculation of the cells and parts of nuclear reactors using a generalized method of first collision probabilities.

  11. Oral Hygiene. Learning Activity Package.

    ERIC Educational Resources Information Center

    Hime, Kirsten

    This learning activity package on oral hygiene is one of a series of 12 titles developed for use in health occupations education programs. Materials in the package include objectives, a list of materials needed, a list of definitions, information sheets, reviews (self evaluations) of portions of the content, and answers to reviews. These topics…

  12. Floriculture. Selected Learning Activity Packages.

    ERIC Educational Resources Information Center

    Clemson Univ., SC. Vocational Education Media Center.

    This series of learning activity packages is based on a catalog of performance objectives, criterion-referenced measures, and performance guides for gardening/groundskeeping developed by the Vocational Education Consortium of States (V-TECS). Learning activity packages are presented in four areas: (1) preparation of soils and planting media, (2)…

  13. Sterility of packaged implant components.

    PubMed

    Worthington, Philip

    2005-01-01

    Several implant components in their original glass vial and peel-back packages were subjected to sterility testing to determine whether the contents remained sterile after the expiration date marked on the package had passed. The results from a university microbiology laboratory showed that the contents remained sterile for 6 to 11 years after the expiration dates. PMID:15973959

  14. Effects of mixed waste simulants on transportation packaging plastic components

    SciTech Connect

    Nigrey, P.J.; Dickens, T.G.

    1994-12-31

    The purpose of hazardous and radioactive materials packaging is to, enable these materials to be transported without posing a threat to the health or property of the general public. To achieve this aim, regulations have been written establishing general design requirements for such packagings. While no regulations have been written specifically for mixed waste packaging, regulations for the constituents of mixed wastes, i.e., hazardous and radioactive substances, have been codified. The design requirements for both hazardous and radioactive materials packaging specify packaging compatibility, i.e., that the materials of the packaging and any contents be chemically compatible with each other. Furthermore, Type A and Type B packaging design requirements stipulate that there be no significant chemical, galvanic, or other reaction between the materials and contents of the package. Based on these requirements, a Chemical Compatibility Testing Program was developed in the Transportation Systems Department at Sandia National Laboratories (SNL). The program, supported by the US Department of Energy`s (DOE) Transportation Management Division, EM-261 provides the means to assure any regulatory body that the issue of packaging material compatibility towards hazardous and radioactive materials has been addressed. In this paper, we describe the general elements of the testing program and the experimental results of the screening tests. The implications of the results of this testing are discussed in the general context of packaging development. Additionally, we present the results of the first phase of this experimental program. This phase involved the screening of five candidate liner and six seal materials against four simulant mixed wastes.

  15. 49 CFR 173.411 - Industrial packagings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Industrial packagings. 173.411 Section 173.411... SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.411 Industrial packagings. (a) General. Each industrial packaging must comply with the requirements of this section which specifies packaging tests,...

  16. 49 CFR 173.411 - Industrial packagings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Industrial packagings. 173.411 Section 173.411... SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.411 Industrial packagings. (a) General. Each industrial packaging must comply with the requirements of this section which specifies packaging tests,...

  17. 49 CFR 173.411 - Industrial packagings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Industrial packagings. 173.411 Section 173.411... SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.411 Industrial packagings. (a) General. Each industrial packaging must comply with the requirements of this section which specifies packaging tests,...

  18. 49 CFR 173.411 - Industrial packages.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Industrial packages. 173.411 Section 173.411... SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.411 Industrial packages. (a) General. Each industrial package must comply with the requirements of this section which specifies package tests,...

  19. 49 CFR 173.411 - Industrial packagings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Industrial packagings. 173.411 Section 173.411... SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.411 Industrial packagings. (a) General. Each industrial packaging must comply with the requirements of this section which specifies packaging tests,...

  20. 10 CFR 71.33 - Package description.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Package description. 71.33 Section 71.33 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Application for Package Approval § 71.33 Package description. The application must include a description of the proposed package in sufficient detail to identify...

  1. 10 CFR 71.33 - Package description.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Package description. 71.33 Section 71.33 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Application for Package Approval § 71.33 Package description. The application must include a description of the proposed package in sufficient detail to identify...

  2. 19 CFR 191.13 - Packaging materials.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Packaging materials. 191.13 Section 191.13 Customs... (CONTINUED) DRAWBACK General Provisions § 191.13 Packaging materials. (a) Imported packaging material... packaging material when used to package or repackage merchandise or articles exported or destroyed...

  3. 49 CFR 173.63 - Packaging exceptions.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Packaging exceptions. 173.63 Section 173.63... SHIPMENTS AND PACKAGINGS Definitions, Classification and Packaging for Class 1 § 173.63 Packaging exceptions...) Cartridges, power devices which are used to project fastening devices. (2) Packaging for Cartridges,...

  4. 19 CFR 191.13 - Packaging materials.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 19 Customs Duties 2 2011-04-01 2011-04-01 false Packaging materials. 191.13 Section 191.13 Customs... (CONTINUED) DRAWBACK General Provisions § 191.13 Packaging materials. (a) Imported packaging material... packaging material when used to package or repackage merchandise or articles exported or destroyed...

  5. 19 CFR 191.13 - Packaging materials.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 19 Customs Duties 2 2012-04-01 2012-04-01 false Packaging materials. 191.13 Section 191.13 Customs... (CONTINUED) DRAWBACK General Provisions § 191.13 Packaging materials. (a) Imported packaging material... packaging material when used to package or repackage merchandise or articles exported or destroyed...

  6. 49 CFR 173.63 - Packaging exceptions.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Packaging exceptions. 173.63 Section 173.63... SHIPMENTS AND PACKAGINGS Definitions, Classification and Packaging for Class 1 § 173.63 Packaging exceptions... fastening devices). (2) Packaging for Cartridges, small arms, Cartridges for tools, blank, Cases,...

  7. 19 CFR 191.13 - Packaging materials.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 19 Customs Duties 2 2013-04-01 2013-04-01 false Packaging materials. 191.13 Section 191.13 Customs... (CONTINUED) DRAWBACK General Provisions § 191.13 Packaging materials. (a) Imported packaging material... packaging material when used to package or repackage merchandise or articles exported or destroyed...

  8. 49 CFR 173.63 - Packaging exceptions.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Packaging exceptions. 173.63 Section 173.63... SHIPMENTS AND PACKAGINGS Definitions, Classification and Packaging for Class 1 § 173.63 Packaging exceptions...) Cartridges, power devices which are used to project fastening devices. (2) Packaging for Cartridges,...

  9. 19 CFR 191.13 - Packaging materials.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 19 Customs Duties 2 2014-04-01 2014-04-01 false Packaging materials. 191.13 Section 191.13 Customs... (CONTINUED) DRAWBACK General Provisions § 191.13 Packaging materials. (a) Imported packaging material... packaging material when used to package or repackage merchandise or articles exported or destroyed...

  10. 49 CFR 173.63 - Packaging exceptions.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Packaging exceptions. 173.63 Section 173.63... SHIPMENTS AND PACKAGINGS Definitions, Classification and Packaging for Class 1 § 173.63 Packaging exceptions... which are used to project fastening devices. (2) Packaging for cartridges, small arms, and...

  11. Modular optimization code package: MOZAIK

    NASA Astrophysics Data System (ADS)

    Bekar, Kursat B.

    This dissertation addresses the development of a modular optimization code package, MOZAIK, for geometric shape optimization problems in nuclear engineering applications. MOZAIK's first mission, determining the optimal shape of the D2O moderator tank for the current and new beam tube configurations for the Penn State Breazeale Reactor's (PSBR) beam port facility, is used to demonstrate its capabilities and test its performance. MOZAIK was designed as a modular optimization sequence including three primary independent modules: the initializer, the physics and the optimizer, each having a specific task. By using fixed interface blocks among the modules, the code attains its two most important characteristics: generic form and modularity. The benefit of this modular structure is that the contents of the modules can be switched depending on the requirements of accuracy, computational efficiency, or compatibility with the other modules. Oak Ridge National Laboratory's discrete ordinates transport code TORT was selected as the transport solver in the physics module of MOZAIK, and two different optimizers, Min-max and Genetic Algorithms (GA), were implemented in the optimizer module of the code package. A distributed memory parallelism was also applied to MOZAIK via MPI (Message Passing Interface) to execute the physics module concurrently on a number of processors for various states in the same search. Moreover, dynamic scheduling was enabled to enhance load balance among the processors while running MOZAIK's physics module thus improving the parallel speedup and efficiency. In this way, the total computation time consumed by the physics module is reduced by a factor close to M, where M is the number of processors. This capability also encourages the use of MOZAIK for shape optimization problems in nuclear applications because many traditional codes related to radiation transport do not have parallel execution capability. A set of computational models based on the

  12. Regulation of mitochondrial translation of the ATP8/ATP6 mRNA by Smt1p

    PubMed Central

    Rak, Malgorzata; Su, Chen Hsien; Xu, Jonathan Tong; Azpiroz, Ricardo; Singh, Angela Mohan; Tzagoloff, Alexander

    2016-01-01

    Expression of the mitochondrially encoded ATP6 and ATP8 genes is translationally regulated by F1 ATPase. We report a translational repressor (Smt1p) of the ATP6/8 mRNA that, when mutated, restores translation of the encoded Atp6p and Atp8p subunits of the ATP synthase. Heterozygous smt1 mutants fail to rescue the translation defect, indicating that the mutations are recessive. Smt1p is an intrinsic inner membrane protein, which, based on its sedimentation, has a native size twice that of the monomer. Affinity purification of tagged Smt1p followed by reverse transcription of the associated RNA and PCR amplification of the resultant cDNA with gene-specific primers demonstrated the presence in mitochondria of Smt1p-ATP8/ATP6 and Smt1p-COB mRNA complexes. These results indicate that Smt1p is likely to be involved in translational regulation of both mRNAs. Applying Occam’s principle, we favor a mechanistic model in which translation of the ATP8/ATP6 bicistronic mRNA is coupled to the availability of F1 for subsequent assembly of the Atp6p and Atp8p products into the ATP synthase. The mechanism of this regulatory pathway is proposed to entail a displacement of the repressor from the translationally mute Smt1-ATP8/ATP6 complex by F1, thereby permitting the Atp22p activator to interact with and promote translation of the mRNA. PMID:26823015

  13. Amesos Solver Package

    2004-03-01

    Amesos is the Direct Sparse Solver Package in Trilinos. The goal of Amesos is to make AX=S as easy as it sounds, at least for direct methods. Amesos provides interfaces to a number of third party sparse direct solvers, including SuperLU, SuperLU MPI, DSCPACK, UMFPACK and KLU. Amesos provides a common object oriented interface to the best sparse direct solvers in the world. A sparse direct solver solves for x in Ax = b. wheremore » A is a matrix and x and b are vectors (or multi-vectors). A sparse direct solver flrst factors A into trinagular matrices L and U such that A = LU via gaussian elimination and then solves LU x = b. Switching amongst solvers in Amesos roquires a change to a single parameter. Yet, no solver needs to be linked it, unless it is used. All conversions between the matrices provided by the user and the format required by the underlying solver is performed by Amesos. As new sparse direct solvers are created, they will be incorporated into Amesos, allowing the user to simpty link with the new solver, change a single parameter in the calling sequence, and use the new solver. Amesos allows users to specify whether the matrix has changed. Amesos can be used anywhere that any sparse direct solver is needed.« less

  14. Nuclear waste packaging facility

    SciTech Connect

    Mallory, C.W.; Watts, R.E.; Paladino, J.B.; Razor, J.E.; Lilley, A.W.; Winston, S.J.; Stricklin, B.C.

    1987-07-21

    A nuclear waste packaging facility comprising: (a) a first section substantially surrounded by radiation shielding, including means for remotely handling waste delivered to the first section and for placing the waste into a disposal module; (b) a second section substantially surrounded by radiation shielding, including means for handling a deformable container bearing waste delivered to the second section, the handling means including a compactor and means for placing the waste bearing deformable container into the compactor, the compactor capable of applying a compacting force to the waste bearing containers sufficient to inelastically deform the waste and container, and means for delivering the deformed waste bearing containers to a disposal module; (c) a module transportation and loading section disposed between the first and second sections including a means for handling empty modules delivered to the facility and for loading the empty modules on the transport means; the transport means moving empty disposal modules to the first section and empty disposal modules to the second section for locating empty modules in a position for loading with nuclear waste, and (d) a grouting station comprising means for pouring grout into the waste bearing disposal module, and a capping station comprising means for placing a lid onto the waste bearing grout-filled disposal module to completely encapsulate the waste.

  15. The CDF software package

    NASA Technical Reports Server (NTRS)

    Wilson, C. E.

    1986-01-01

    The concepts that are fundamental to the new Common Data Format are outlined. With Pilot Climate Data System (PCDS) Version 4.0, the Common Data Format (CDF) will supersede the Climate Data File (also CDF) or earlier versions. This new format incorporates generalizations in both design and terminology that make it applicable to multidisciplinary data sets. Furthermore, the new CDF will be made available to programmers as a software package that shields them from the low-level details of file formats. The CDF interface routines create an abstract conceptual environment for the scientific programmer. The principle concept for visualizing a CDF is known as the basic grid. A basic grid is an n-dimensional block by means of which a CDF is constructed. The size of the block may vary from one CDF to another, but is consistent within any individual CDF. Thus, the basic grid serves as a fundamental uniform building block for a CDF. The number of grid dimensions and the size of each dimension are chosen by the scientist/programmer to represent the patterns by which data are structured. The uniform grid structure appears to the programmer to be propagated into each record for each variable. The CDF stores a variable value for each lattice point of the grid for each record. These data values are inserted and retrieved simply by specifying the variable's identifier, a record number, and the indices that specify the lattice point of interest.

  16. Particle Environment Package (PEP)

    NASA Astrophysics Data System (ADS)

    Barabash, S.; Wurz, P.; Brandt, P.; Wieser, M.; Holmström, M.; Futaana, Y.; Stenberg, G.; Nilsson, H.; Eriksson, A.; Tulej, M.; Vorburger, A.; Thomas, N.; Paranicas, C.; Mitchell, D. G.; Ho, G.; Mauk, B. H.; Haggerty, D.; Westlake, J. H.; Fränz, M.; Krupp, N.; Roussos, E.; Kallio, E.; Schmidt, W.; Szego, K.; Szalai, S.; Khurana, Krishan; Jia, Xianzhe; Paty, C.; Wimmer-Schweingruber, R. F.; Heber, B.; Kazushi, Asamura; Grande, M.; Lammer, H.; Zhang, T.; McKenna-Lawlor, S.; Krimigis, S. M.; Sarris, Th.; Grodent, D.

    2013-09-01

    Particle Environment Package (PEP) is a suite of particle sensors proposed for the ESA JUICE mission. PEP includes sensors for the comprehensive measurements of electrons, ions, energetic neutrals, and neutral gas. PEP covers over nine decades of energy <0.001 eV to >1 MeV with full angular coverage. Combining remote global imaging via energetic neutral atoms (ENAs) with in-situ measurements, PEP addresses all scientific objectives of the JUICE mission relevant to particle measurements. PEP will seek answers for four overarching science questions: How does the corotating magnetosphere of Jupiter interact with complex and diverse environment of Ganymede? How does the rapidly rotating magnetosphere of Jupiter interact with seemingly inert Callisto? What are the governing mechanisms and their global impact of release of material into the Jupiter magnetosphere from Europa and Io? How do internal and solar wind drivers cause such energetic, time variable and multi-scale phenomena in the steadily rotating giant magnetosphere of Jupiter? We discuss the suite's sensor basic design, performance, radiation mitigation principles and demonstrate how the suite fully addresses its scientific objectives.

  17. Amesos Solver Package

    SciTech Connect

    Stanley, Vendall S.; Heroux, Michael A.; Hoekstra, Robert J.; Sala, Marzio

    2004-03-01

    Amesos is the Direct Sparse Solver Package in Trilinos. The goal of Amesos is to make AX=S as easy as it sounds, at least for direct methods. Amesos provides interfaces to a number of third party sparse direct solvers, including SuperLU, SuperLU MPI, DSCPACK, UMFPACK and KLU. Amesos provides a common object oriented interface to the best sparse direct solvers in the world. A sparse direct solver solves for x in Ax = b. where A is a matrix and x and b are vectors (or multi-vectors). A sparse direct solver flrst factors A into trinagular matrices L and U such that A = LU via gaussian elimination and then solves LU x = b. Switching amongst solvers in Amesos roquires a change to a single parameter. Yet, no solver needs to be linked it, unless it is used. All conversions between the matrices provided by the user and the format required by the underlying solver is performed by Amesos. As new sparse direct solvers are created, they will be incorporated into Amesos, allowing the user to simpty link with the new solver, change a single parameter in the calling sequence, and use the new solver. Amesos allows users to specify whether the matrix has changed. Amesos can be used anywhere that any sparse direct solver is needed.

  18. Packaging Considerations for Biopreservation

    PubMed Central

    Woods, Erik J.; Thirumala, Sreedhar

    2011-01-01

    Summary The packaging system chosen for biopreservation is critical for many reasons. An ideal biopreservation container system must provide for closure integrity, sample stability and ready access to the preserved material. This means the system needs to be hermetically sealed to ensure integrity of the specimen is maintained throughout processing, storage and distribution; the system must remain stable over long periods of time as many biobanked samples may be stored indefinitely; and functionally closed access systems must be used to avoid contamination upon sample withdraw. This study reviews the suitability of a new commercially available vial configuration container utilizing blood bag style closure and access systems that can be hermetically sealed and remain stable through cryopreservation and biobanking procedures. This vial based systems allow for current good manufacturing/tissue practice (cGTP) requirements during processing of samples and may provide the benefit of ease of delivery by a care giver. In this study, the CellSeal® closed system cryovial was evaluated and compared to standard screw cap vials. The CellSeal system was evaluated for durability, closure integrity through transportation and maintenance of functional viability of a cryopreserved mesenchymal stem cell model. The results of this initial proof-of-concept study indicated that the CellSeal vials are highly suitable for biopreservation and biobanking, and provide a suitable container system for clinical and commercial cell therapy products frozen in small volumes. PMID:21566715

  19. Non-Destructive Testing for Control of Radioactive Waste Package

    NASA Astrophysics Data System (ADS)

    Plumeri, S.; Carrel, F.

    2015-10-01

    Characterization and control of radioactive waste packages are important issues in the management of a radioactive waste repository. Therefore, Andra performs quality control inspection on radwaste package before disposal to ensure the compliance of the radwast characteristics with Andra waste disposal specifications and to check the consistency between Andra measurements results and producer declared properties. Objectives of this quality control are: assessment and improvement of producer radwaste packages quality mastery, guarantee of the radwaste disposal safety, maintain of the public confidence. To control radiological characteristics of radwaste package, non-destructive passive methods (gamma spectrometry and neutrons counting) are commonly used. These passive methods may not be sufficient, for instance to control the mass of fissile material contained inside radwaste package. This is particularly true for large concrete hull of heterogeneous radwaste containing several actinides mixed with fission products like 137Cs. Non-destructive active methods, like measurement of photofission delayed neutrons, allow to quantify the global mass of actinides and is a promising method to quantify mass of fissile material. Andra has performed different non-destructive measurements on concrete intermediate-level short lived nuclear waste (ILW-SL) package to control its nuclear material content. These tests have allowed Andra to have a first evaluation of the performance of photofission delayed neutron measurement and to identify development needed to have a reliable method, especially for fissile material mass control in intermediate-level long lived waste package.

  20. Thermal analysis of Perforated Metal Air Transportable Package (PMATP) prototype.

    SciTech Connect

    Oneto, Robert; Levine, Howard; Mould, John; Pierce, Jim Dwight

    2003-08-01

    Sandia National Laboratories (SNL) has designed a crash-resistant container, the Perforated Metal Air Transportable Package (PMATP), capable of surviving a worst-case plane crash, including both impact and subsequent fire, for the air transport of plutonium. This report presents thermal analyses of the full-scale PMATP in its undamaged (pre-test) condition and in bounding post-accident states. The goal of these thermal simulations was to evaluate the performance of the package in a worst-case post-crash fire. The full-scale package is approximately 1.6 m long by 0.8 m diameter. The thermal analyses were performed with the FLEX finite element code. This analysis clearly predicts that the PMATP provides acceptable thermal response characteristics, both for the post-accident fire of a one-hour duration and the after-fire heat-soak condition. All predicted temperatures for the primary containment vessel are well within design limits for safety.

  1. In-Package Chemistry Abstraction

    SciTech Connect

    E. Thomas

    2004-11-09

    This report was developed in accordance with the requirements in ''Technical Work Plan for: Regulatory Integration Modeling and Analysis of the Waste Form and Waste Package'' (BSC 2004 [DIRS 171583]). The purpose of the in-package chemistry model is to predict the bulk chemistry inside of a breached waste package and to provide simplified expressions of that chemistry as function of time after breach to Total Systems Performance Assessment for the License Application (TSPA-LA). The scope of this report is to describe the development and validation of the in-package chemistry model. The in-package model is a combination of two models, a batch reactor model that uses the EQ3/6 geochemistry-modeling tool, and a surface complexation model that is applied to the results of the batch reactor model. The batch reactor model considers chemical interactions of water with the waste package materials and the waste form for commercial spent nuclear fuel (CSNF) waste packages and codisposed waste packages that contain both high-level waste glass (HLWG) and DOE spent fuel. The surface complexation model includes the impact of fluid-surface interactions (i.e., surface complexation) on the resulting fluid composition. The model examines two types of water influx: (1) the condensation of water vapor that diffuses into the waste package, and (2) seepage water that enters the waste package from the drift as a liquid. (1) Vapor Influx Case: The condensation of vapor onto the waste package internals is simulated as pure H2O and enters at a rate determined by the water vapor pressure for representative temperature and relative humidity conditions. (2) Water Influx Case: The water entering a waste package from the drift is simulated as typical groundwater and enters at a rate determined by the amount of seepage available to flow through openings in a breached waste package. TSPA-LA uses the vapor influx case for the nominal scenario for simulations where the waste package has been

  2. Optimal segmentation and packaging process

    DOEpatents

    Kostelnik, K.M.; Meservey, R.H.; Landon, M.D.

    1999-08-10

    A process for improving packaging efficiency uses three dimensional, computer simulated models with various optimization algorithms to determine the optimal segmentation process and packaging configurations based on constraints including container limitations. The present invention is applied to a process for decontaminating, decommissioning (D and D), and remediating a nuclear facility involving the segmentation and packaging of contaminated items in waste containers in order to minimize the number of cuts, maximize packaging density, and reduce worker radiation exposure. A three-dimensional, computer simulated, facility model of the contaminated items are created. The contaminated items are differentiated. The optimal location, orientation and sequence of the segmentation and packaging of the contaminated items is determined using the simulated model, the algorithms, and various constraints including container limitations. The cut locations and orientations are transposed to the simulated model. The contaminated items are actually segmented and packaged. The segmentation and packaging may be simulated beforehand. In addition, the contaminated items may be cataloged and recorded. 3 figs.

  3. Laser Welding in Electronic Packaging

    NASA Technical Reports Server (NTRS)

    2000-01-01

    The laser has proven its worth in numerous high reliability electronic packaging applications ranging from medical to missile electronics. In particular, the pulsed YAG laser is an extremely flexible and versatile too] capable of hermetically sealing microelectronics packages containing sensitive components without damaging them. This paper presents an overview of details that must be considered for successful use of laser welding when addressing electronic package sealing. These include; metallurgical considerations such as alloy and plating selection, weld joint configuration, design of optics, use of protective gases and control of thermal distortions. The primary limitations on use of laser welding electronic for packaging applications are economic ones. The laser itself is a relatively costly device when compared to competing welding equipment. Further, the cost of consumables and repairs can be significant. These facts have relegated laser welding to use only where it presents a distinct quality or reliability advantages over other techniques of electronic package sealing. Because of the unique noncontact and low heat inputs characteristics of laser welding, it is an ideal candidate for sealing electronic packages containing MEMS devices (microelectromechanical systems). This paper addresses how the unique advantages of the pulsed YAG laser can be used to simplify MEMS packaging and deliver a product of improved quality.

  4. Naval Waste Package Design Sensitivity

    SciTech Connect

    T. Schmitt

    2006-12-13

    The purpose of this calculation is to determine the sensitivity of the structural response of the Naval waste packages to varying inner cavity dimensions when subjected to a comer drop and tip-over from elevated surface. This calculation will also determine the sensitivity of the structural response of the Naval waste packages to the upper bound of the naval canister masses. The scope of this document is limited to reporting the calculation results in terms of through-wall stress intensities in the outer corrosion barrier. This calculation is intended for use in support of the preliminary design activities for the license application design of the Naval waste package. It examines the effects of small changes between the naval canister and the inner vessel, and in these dimensions, the Naval Long waste package and Naval Short waste package are similar. Therefore, only the Naval Long waste package is used in this calculation and is based on the proposed potential designs presented by the drawings and sketches in References 2.1.10 to 2.1.17 and 2.1.20. All conclusions are valid for both the Naval Long and Naval Short waste packages.

  5. Safety evaluation for packaging (onsite) concrete-lined waste packaging

    SciTech Connect

    Romano, T.

    1997-09-25

    The Pacific Northwest National Laboratory developed a package to ship Type A, non-transuranic, fissile excepted quantities of liquid or solid radioactive material and radioactive mixed waste to the Central Waste Complex for storage on the Hanford Site.

  6. Packaging of solid state devices

    DOEpatents

    Glidden, Steven C.; Sanders, Howard D.

    2006-01-03

    A package for one or more solid state devices in a single module that allows for operation at high voltage, high current, or both high voltage and high current. Low thermal resistance between the solid state devices and an exterior of the package and matched coefficient of thermal expansion between the solid state devices and the materials used in packaging enables high power operation. The solid state devices are soldered between two layers of ceramic with metal traces that interconnect the devices and external contacts. This approach provides a simple method for assembling and encapsulating high power solid state devices.

  7. The cell proliferation kinetics of the EMT6/M/AC mouse tumour at four volumes during unperturbed growth in vivo.

    PubMed

    Watson, J V

    1976-03-01

    The cell proliferation kinetics of the EMT6/M/AC mouse tumour were determined at four different volumes between 1-5 mm3 and 175 mm3. The decrease in the growth rate between these volumes are mainly due to a decrease in the rate constant for cell production. A small increase in the rate constant for cell loss occurred, but this was thought to be insignificant. The cell loss factor increased from 40% at 1-5 mm3 to over 70% in the 175 mm3 tumours. An increase in the median cell cycle time, from 14-1 hr to 18-5 hr was also found between these same volumes. Results obtained for the NCTC fibrosarcoma and the R-1 rhabdo-myosarcoms indicate that there may be a threshold volume in these sarcomas below which little or no cell loss takes place. This was not found in the EMT6/M/AC tumour. PMID:1260835

  8. Density Functional Study of the magnetic structure on spin frustrated MnSb2 S 4 and Sr2 MOsO 6 (M = Cu, Ni)

    NASA Astrophysics Data System (ADS)

    Tian, Chuan; Lee, Changhoon; Kan, Erjun; Wu, Fang; Whangbo, Mike

    2011-03-01

    We explored the electronic structures of two spin-frustrated magnetic systems monoclinic MnSb 2 S4 and Sr 2 MOs O6 (M = Cu, Ni) on the basis of first principles DFT calculations. The spin exchanges of MnSb 2 S4 are frustrated within each Mn S4 chain and between adjacent Mn S4 chains, which explains the observed helical spin order of MnSb 2 S4 . We predict that MnSb 2 S4 is multiferroic with ferroelectric polarization of ~ 14 μ C/ m 2 along the chain direction, and a field-induced reversal of the ferroelectric polarization occurs by reversing the direction of the helical spin rotation. The ordered double perovskites Sr 2 MOs O6 (M = Cu, Ni), reported to be half-metallic, are found to be magnetic insulators. The magnetic structures of Sr 2 MOs O6 were probed by evaluating their spin exchanges.

  9. Optical Set-Up and Design for Solar Multi-conjugate Adaptive Optics at the 1.6m New Solar Telescope, Big Bear Solar Observatory

    NASA Astrophysics Data System (ADS)

    Moretto, Gil; Langlois, Maud; Goode, Philip; Gorceix, Nicolas; Shumko, Sergey

    2013-12-01

    The Sun is an ideal target for the development and application of Multi-Conjugate Adaptive Optics (MCAO). A solar MCAO system is being developed by the Big Bear Solar Observatory, for the 1.6m New Solar Observatory, with the purpose of extending the corrected science field of view to 1.00Arcmin. A preliminary optical set-up, design and optical performance for such a system is presented and discussed here.

  10. LONG TERM AGING AND SURVEILLANCE OF 9975 PACKAGE COMPONENTS

    SciTech Connect

    Hoffman, E.; Skidmore, E.; Daugherty, W.; Dunn, K.

    2009-11-10

    The mission of the 9975 package, originally designed only for transportation of radioactive materials, has been broadened to include storage at the Savannah River Site. Two components of this package, namely the containment vessel O-rings and fiberboard overpack, require continued integrity assessment under the storage conditions. The performance of the components over time is being evaluated using accelerated-aging studies. Compression stress relaxation (CSR) and leak testing are being used to measure the performance of O-rings. The performance of the fiberboard is being evaluated using compression strength, thermal conductivity, specific heat capacity and other physical properties. Models developed from the data collected provide an initial prediction of service life for the two components, and support the conclusion that normal service conditions will not degrade the performance of the package beyond specified functional requirements for the first assessment interval. Increased confidence in this conclusion is derived from field surveillance data and destructive evaluation of packages removed from storage.

  11. Book of Knowledge (BOK) for NASA Electronic Packaging Roadmap

    NASA Technical Reports Server (NTRS)

    Ghaffarian, Reza

    2015-01-01

    The objective of this document is to update the NASA roadmap on packaging technologies (initially released in 2007) and to present the current trends toward further reducing size and increasing functionality. Due to the breadth of work being performed in the area of microelectronics packaging, this report presents only a number of key packaging technologies detailed in three industry roadmaps for conventional microelectronics and a more recently introduced roadmap for organic and printed electronics applications. The topics for each category were down-selected by reviewing the 2012 reports of the International Technology Roadmap for Semiconductor (ITRS), the 2013 roadmap reports of the International Electronics Manufacturing Initiative (iNEMI), the 2013 roadmap of association connecting electronics industry (IPC), the Organic Printed Electronics Association (OE-A). The report also summarizes the results of numerous articles and websites specifically discussing the trends in microelectronics packaging technologies.

  12. RNA secondary structures of the bacteriophage phi6 packaging regions.

    PubMed Central

    Pirttimaa, M J; Bamford, D H

    2000-01-01

    Bacteriophage phi6 genome consists of three segments of double-stranded RNA. During maturation, single-stranded copies of these segments are packaged into preformed polymerase complex particles. Only phi6 RNA is packaged, and each particle contains only one copy of each segment. An in vitro packaging and replication assay has been developed for phi6, and the packaging signals (pac sites) have been mapped to the 5' ends of the RNA segments. In this study, we propose secondary structure models for the pac sites of phi6 single-stranded RNA segments. Our models accommodate data from structure-specific chemical modifications, free energy minimizations, and phylogenetic comparisons. Previously reported pac site deletion studies are also discussed. Each pac site possesses a unique architecture, that, however, contains common structural elements. PMID:10864045

  13. Conservation of a Packaging Signal and the Viral Genome RNA Packaging Mechanism in Alphavirus Evolution ▿

    PubMed Central

    Kim, Dal Young; Firth, Andrew E.; Atasheva, Svetlana; Frolova, Elena I.; Frolov, Ilya

    2011-01-01

    Alphaviruses are a group of small, enveloped viruses which are widely distributed on all continents. In infected cells, alphaviruses display remarkable specificity in RNA packaging by encapsidating only their genomic RNA while avoiding packaging of the more abundant viral subgenomic (SG), cellular messenger and transfer RNAs into released virions. In this work, we demonstrate that in spite of evolution in geographically isolated areas and accumulation of considerable diversity in the nonstructural and structural genes, many alphaviruses belonging to different serocomplexes harbor RNA packaging signals (PSs) which contain the same structural and functional elements. Their characteristic features are as follows. (i) Sindbis, eastern, western, and Venezuelan equine encephalitis and most likely many other alphaviruses, except those belonging to the Semliki Forest virus (SFV) clade, have PSs which can be recognized by the capsid proteins of heterologous alphaviruses. (ii) The PS consists of 4 to 6 stem-loop RNA structures bearing conserved GGG sequences located at the base of the loop. These short motifs are integral elements of the PS and can function even in the artificially designed PS. (iii) Mutagenesis of the entire PS or simply the GGG sequences has strong negative effects on viral genome packaging and leads to release of viral particles containing mostly SG RNAs. (iv) Packaging of RNA appears to be determined to some extent by the number of GGG-containing stem-loops, and more than one stem-loop is required for efficient RNA encapsidation. (v) Viruses of the SFV clade are the exception to the general rule. They contain PSs in the nsP2 gene, but their capsid protein retains the ability to use the nsP1-specific PS of other alphaviruses. These new discoveries regarding alphavirus PS structure and function provide an opportunity for the development of virus variants, which are irreversibly attenuated in terms of production of infectious virus but release high levels

  14. Solar Control design package

    NASA Technical Reports Server (NTRS)

    1978-01-01

    Information used in the evaluation of design of Solar Control's solar heating and cooling system controller and the Solarstat is given. Some of the information includes system performance specifications, design data brochures, and detailed design drawings.

  15. Large area LED package

    NASA Astrophysics Data System (ADS)

    Goullon, L.; Jordan, R.; Braun, T.; Bauer, J.; Becker, F.; Hutter, M.; Schneider-Ramelow, M.; Lang, K.-D.

    2015-03-01

    Solid state lighting using LED-dies is a rapidly growing market. LED-dies with the needed increasing luminous flux per chip area produce a lot of heat. Therefore an appropriate thermal management is required for general lighting with LEDdies. One way to avoid overheating and shorter lifetime is the use of many small LED-dies on a large area heat sink (down to 70 μm edge length), so that heat can spread into a large area while at the same time light also appears on a larger area. The handling with such small LED-dies is very difficult because they are too small to be picked with common equipment. Therefore a new concept called collective transfer bonding using a temporary carrier chip was developed. A further benefit of this new technology is the high precision assembly as well as the plane parallel assembly of the LED-dies which is necessary for wire bonding. It has been shown that hundred functional LED-dies were transferred and soldered at the same time. After the assembly a cost effective established PCB-technology was applied to produce a large-area light source consisting of many small LED-dies and electrically connected on a PCB-substrate. The top contacts of the LED-dies were realized by laminating an adhesive copper sheet followed by LDI structuring as known from PCB-via-technology. This assembly can be completed by adding converting and light forming optical elements. In summary two technologies based on standard SMD and PCB technology have been developed for panel level LED packaging up to 610x 457 mm2 area size.

  16. Identification and characterization of a coronavirus packaging signal.

    PubMed Central

    Fosmire, J A; Hwang, K; Makino, S

    1992-01-01

    Previously, a mouse hepatitis virus (MHV) genomic sequence necessary for defective interfering (DI) RNA packaging into MHV particles (packaging signal) was mapped to within a region of 1,480 nucleotides in the MHV polymerase gene by comparison of two DI RNAs. One of these, DIssF, is 3.6 kb in size and exhibits efficient packaging, whereas the other, DIssE, which is 2.3 kb, does not. For more precise mapping, a series of mutant DIssF RNAs with deletions within this 1,480-nucleotide region were constructed. After transfection of in vitro-synthesized mutant DI RNA in MHV-infected cells, the virus product was passaged several times. The efficiency of DI RNA packaging into MHV virions was then estimated by viral homologous interference activity and by analysis of intracellular virus-specific RNAs and virion RNA. The results indicated that an area of 190 nucleotides was necessary for packaging. A computer-generated secondary structural analysis of the A59 and JHM strains of MHV demonstrated that within this 190-nucleotide region a stable stem-loop of 69 nucleotides was common between the two viruses. A DIssE-derived DI DNA which had these 69 nucleotides inserted into the DIssE sequence demonstrated efficient DI RNA packaging. Site-directed mutagenic analysis showed that of these 69 nucleotides, the minimum sequence of the packaging signal was 61 nucleotides and that destruction of the secondary structure abolished packaging ability. These studies demonstrated that an MHV packaging signal was present within the 61 nucleotides, which are located on MHV genomic RNA 1,381 to 1,441 nucleotides upstream of the 3' end of gene 1. Images PMID:1316465

  17. General Corrosion and Localized Corrosion of Waste Package Outer Barrier

    SciTech Connect

    K.G. Mon

    2004-10-01

    The waste package design for the License Application is a double-wall waste package underneath a protective drip shield (BSC 2004 [DIRS 168489]; BSC 2004 [DIRS 169480]). The purpose and scope of this model report is to document models for general and localized corrosion of the waste package outer barrier (WPOB) to be used in evaluating waste package performance. The WPOB is constructed of Alloy 22 (UNS N06022), a highly corrosion-resistant nickel-based alloy. The inner vessel of the waste package is constructed of Stainless Steel Type 316 (UNS S31600). Before it fails, the Alloy 22 WPOB protects the Stainless Steel Type 316 inner vessel from exposure to the external environment and any significant degradation. The Stainless Steel Type 316 inner vessel provides structural stability to the thinner Alloy 22 WPOB. Although the waste package inner vessel would also provide some performance for waste containment and potentially decrease the rate of radionuclide transport after WPOB breach before it fails, the potential performance of the inner vessel is far less than that of the more corrosion-resistant Alloy 22 WPOB. For this reason, the corrosion performance of the waste package inner vessel is conservatively ignored in this report and the total system performance assessment for the license application (TSPA-LA). Treatment of seismic and igneous events and their consequences on waste package outer barrier performance are not specifically discussed in this report, although the general and localized corrosion models developed in this report are suitable for use in these scenarios. The localized corrosion processes considered in this report are pitting corrosion and crevice corrosion. Stress corrosion cracking is discussed in ''Stress Corrosion Cracking of the Drip Shield, the Waste Package Outer Barrier, and the Stainless Steel Structural Material'' (BSC 2004 [DIRS 169985]).

  18. PACKAGING CERTIFICATION PROGRAM METHODOLOGY FOR DETERMINING DOSE RATES FOR SMALL GRAM QUANTITIES IN SHIPPING PACKAGINGS

    SciTech Connect

    Nathan, S.; Loftin, B.; Abramczyk, G.; Bellamy, S.

    2012-05-09

    The Small Gram Quantity (SGQ) concept is based on the understanding that small amounts of hazardous materials, in this case radioactive materials (RAM), are significantly less hazardous than large amounts of the same materials. This paper describes a methodology designed to estimate an SGQ for several neutron and gamma emitting isotopes that can be shipped in a package compliant with 10 CFR Part 71 external radiation level limits regulations. These regulations require packaging for the shipment of radioactive materials, under both normal and accident conditions, to perform the essential functions of material containment, subcriticality, and maintain external radiation levels within the specified limits. By placing the contents in a helium leak-tight containment vessel, and limiting the mass to ensure subcriticality, the first two essential functions are readily met. Some isotopes emit sufficiently strong photon radiation that small amounts of material can yield a large dose rate outside the package. Quantifying the dose rate for a proposed content is a challenging issue for the SGQ approach. It is essential to quantify external radiation levels from several common gamma and neutron sources that can be safely placed in a specific packaging, to ensure compliance with federal regulations. The Packaging Certification Program (PCP) Methodology for Determining Dose Rate for Small Gram Quantities in Shipping Packagings provides bounding shielding calculations that define mass limits compliant with 10 CFR 71.47 for a set of proposed SGQ isotopes. The approach is based on energy superposition with dose response calculated for a set of spectral groups for a baseline physical packaging configuration. The methodology includes using the MCNP radiation transport code to evaluate a family of neutron and photon spectral groups using the 9977 shipping package and its associated shielded containers as the base case. This results in a set of multipliers for 'dose per particle' for

  19. 49 CFR 173.242 - Bulk packagings for certain medium hazard liquids and solids, including solids with dual hazards.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Hazardous Materials Table for a specific hazardous material; and marine portable tanks conforming to 46 CFR..., Packaging Group II materials must conform to the following: (1) Minimum design pressure. Each tank must have... Packaging for Hazardous Materials Other Than Class 1 and Class 7 § 173.242 Bulk packagings for...

  20. Polylactide nanocomposites for packaging materials: A review

    NASA Astrophysics Data System (ADS)

    Widiastuti, Indah

    2016-02-01

    This review aims at highlighting on an attempt for improving the properties of polylactide (PLA) as packaging material by application of nanocomposite technology. PLA is attracting considerable interest because of more eco-friendliness from its origin as contrast to the petrochemical-based polymers and its biodegradability. Despite possessing good mechanical and optical properties, deterioration of the material properties in PLA materials during their service time could occur after prolonged exposure to humidity and high temperature condition. Limited gas barrier is another drawback of PLA material that should be overcome to satisfy the requirement for packaging application. To further extend the range of mechanical and thermal properties achievable, several attempts have been made in modifying the material such as blending with other polymers, use of plasticizing material and development of PLA nanocomposites. Nanocomposite is a fairly new type of composite that has emerged in which the reinforcing filler has nanometer scale dimensions (at least one dimension of the filler is less than 100 nm). In this review, the critical properties of PLA as packaging materials and its degradation mechanism are presented. This paper discusses the current effort and key research challenges in the development of nanocomposites based on biodegradable polymer matrices and nano-fillers. The PLA layered silicate nanocomposites where the filler platelets can be dispersed in the polymer at the nanometer scale owing to the specific filler surface modification, frequently exhibits remarkable improvements of mechanical strength, gas barrier and thermal stability.

  1. High Frequency Electronic Packaging Technology

    NASA Technical Reports Server (NTRS)

    Herman, M.; Lowry, L.; Lee, K.; Kolawa, E.; Tulintseff, A.; Shalkhauser, K.; Whitaker, J.; Piket-May, M.

    1994-01-01

    Commercial and government communication, radar, and information systems face the challenge of cost and mass reduction via the application of advanced packaging technology. A majority of both government and industry support has been focused on low frequency digital electronics.

  2. Spack: the Supercomputing Package Manager

    2013-11-09

    The HPC software ecosystem is growing larger and more complex, but software distribution mechanisms have not kept up with this trend. Tools, Libraries, and applications need to run on multiple platforms and build with multiple compliers. Increasingly, packages leverage common software components, and building any one component requires building all of its dependencies. In HPC environments, ABI-incompatible interfaces (likeMPI), binary-incompatible compilers, and cross-compiled environments converge to make the build process a combinatoric nightmare. This obstaclemore » deters many users from adopting useful tools, and others waste countless hours building and rebuilding tools. Many package managers exist to solve these problems for typical desktop environments, but none suits the unique needs of supercomputing facilities or users. To address these problems, we have Spack, a package manager that eases the task of managing software for end-users, across multiple platforms, package versions, compilers, and ABI incompatibilities.« less

  3. Spack: the Supercomputing Package Manager

    SciTech Connect

    Gamblin, T.

    2013-11-09

    The HPC software ecosystem is growing larger and more complex, but software distribution mechanisms have not kept up with this trend. Tools, Libraries, and applications need to run on multiple platforms and build with multiple compliers. Increasingly, packages leverage common software components, and building any one component requires building all of its dependencies. In HPC environments, ABI-incompatible interfaces (likeMPI), binary-incompatible compilers, and cross-compiled environments converge to make the build process a combinatoric nightmare. This obstacle deters many users from adopting useful tools, and others waste countless hours building and rebuilding tools. Many package managers exist to solve these problems for typical desktop environments, but none suits the unique needs of supercomputing facilities or users. To address these problems, we have Spack, a package manager that eases the task of managing software for end-users, across multiple platforms, package versions, compilers, and ABI incompatibilities.

  4. New Packaging for Amplifier Slabs

    SciTech Connect

    Riley, M.; Thorsness, C.; Suratwala, T.; Steele, R.; Rogowski, G.

    2015-03-18

    The following memo provides a discussion and detailed procedure for a new finished amplifier slab shipping and storage container. The new package is designed to maintain an environment of <5% RH to minimize weathering.

  5. Packaging Review Guide for Reviewing Safety Analysis Reports for Packagings

    SciTech Connect

    DiSabatino, A; Biswas, D; DeMicco, M; Fisher, L E; Hafner, R; Haslam, J; Mok, G; Patel, C; Russell, E

    2007-04-12

    This Packaging Review Guide (PRG) provides guidance for Department of Energy (DOE) review and approval of packagings to transport fissile and Type B quantities of radioactive material. It fulfills, in part, the requirements of DOE Order 460.1B for the Headquarters Certifying Official to establish standards and to provide guidance for the preparation of Safety Analysis Reports for Packagings (SARPs). This PRG is intended for use by the Headquarters Certifying Official and his or her review staff, DOE Secretarial offices, operations/field offices, and applicants for DOE packaging approval. This PRG is generally organized at the section level in a format similar to that recommended in Regulatory Guide 7.9 (RG 7.9). One notable exception is the addition of Section 9 (Quality Assurance), which is not included as a separate chapter in RG 7.9. Within each section, this PRG addresses the technical and regulatory bases for the review, the manner in which the review is accomplished, and findings that are generally applicable for a package that meets the approval standards. This Packaging Review Guide (PRG) provides guidance for DOE review and approval of packagings to transport fissile and Type B quantities of radioactive material. It fulfills, in part, the requirements of DOE O 460.1B for the Headquarters Certifying Official to establish standards and to provide guidance for the preparation of Safety Analysis Reports for Packagings (SARPs). This PRG is intended for use by the Headquarters Certifying Official and his review staff, DOE Secretarial offices, operations/field offices, and applicants for DOE packaging approval. The primary objectives of this PRG are to: (1) Summarize the regulatory requirements for package approval; (2) Describe the technical review procedures by which DOE determines that these requirements have been satisfied; (3) Establish and maintain the quality and uniformity of reviews; (4) Define the base from which to evaluate proposed changes in scope

  6. Qualification and Reliability for MEMS and IC Packages

    NASA Technical Reports Server (NTRS)

    Ghaffarian, Reza

    2004-01-01

    Advanced IC electronic packages are moving toward miniaturization from two key different approaches, front and back-end processes, each with their own challenges. Successful use of more of the back-end process front-end, e.g. microelectromechanical systems (MEMS) Wafer Level Package (WLP), enable reducing size and cost. Use of direct flip chip die is the most efficient approach if and when the issues of know good die and board/assembly are resolved. Wafer level package solve the issue of known good die by enabling package test, but it has its own limitation, e.g., the I/O limitation, additional cost, and reliability. From the back-end approach, system-in-a-package (SIAP/SIP) development is a response to an increasing demand for package and die integration of different functions into one unit to reduce size and cost and improve functionality. MEMS add another challenging dimension to electronic packaging since they include moving mechanical elements. Conventional qualification and reliability need to be modified and expanded in most cases in order to detect new unknown failures. This paper will review four standards that already released or being developed that specifically address the issues on qualification and reliability of assembled packages. Exposures to thermal cycles, monotonic bend test, mechanical shock and drop are covered in these specifications. Finally, mechanical and thermal cycle qualification data generated for MEMS accelerometer will be presented. The MEMS was an element of an inertial measurement unit (IMU) qualified for NASA Mars Exploration Rovers (MERs), Spirit and Opportunity that successfully is currently roaring the Martian surface

  7. CompHEP/SUSY package

    NASA Astrophysics Data System (ADS)

    Semenov, A.

    2003-04-01

    The CompHEP software package allows evaluation of cross-section and decays of elementary particles with a high level of automation. Arbitrary tree level processes can be calculated starting from the set of vertices prescribed by a given physical model. This article describes implementation of the Minimal Supersymmetric Standard Model in the CompHEP package. Several CompHEP/SUSY models can be found on the WWW page http://theory.sinp.msu.ru/~semenov/mssm.html.

  8. Watermarking spot colors in packaging

    NASA Astrophysics Data System (ADS)

    Reed, Alastair; Filler, TomáÅ.¡; Falkenstern, Kristyn; Bai, Yang

    2015-03-01

    In January 2014, Digimarc announced Digimarc® Barcode for the packaging industry to improve the check-out efficiency and customer experience for retailers. Digimarc Barcode is a machine readable code that carries the same information as a traditional Universal Product Code (UPC) and is introduced by adding a robust digital watermark to the package design. It is imperceptible to the human eye but can be read by a modern barcode scanner at the Point of Sale (POS) station. Compared to a traditional linear barcode, Digimarc Barcode covers the whole package with minimal impact on the graphic design. This significantly improves the Items per Minute (IPM) metric, which retailers use to track the checkout efficiency since it closely relates to their profitability. Increasing IPM by a few percent could lead to potential savings of millions of dollars for retailers, giving them a strong incentive to add the Digimarc Barcode to their packages. Testing performed by Digimarc showed increases in IPM of at least 33% using the Digimarc Barcode, compared to using a traditional barcode. A method of watermarking print ready image data used in the commercial packaging industry is described. A significant proportion of packages are printed using spot colors, therefore spot colors needs to be supported by an embedder for Digimarc Barcode. Digimarc Barcode supports the PANTONE spot color system, which is commonly used in the packaging industry. The Digimarc Barcode embedder allows a user to insert the UPC code in an image while minimizing perceptibility to the Human Visual System (HVS). The Digimarc Barcode is inserted in the printing ink domain, using an Adobe Photoshop plug-in as the last step before printing. Since Photoshop is an industry standard widely used by pre-press shops in the packaging industry, a Digimarc Barcode can be easily inserted and proofed.

  9. Rapid Active Sampling Package

    NASA Technical Reports Server (NTRS)

    Peters, Gregory

    2010-01-01

    A field-deployable, battery-powered Rapid Active Sampling Package (RASP), originally designed for sampling strong materials during lunar and planetary missions, shows strong utility for terrestrial geological use. The technology is proving to be simple and effective for sampling and processing materials of strength. Although this originally was intended for planetary and lunar applications, the RASP is very useful as a powered hand tool for geologists and the mining industry to quickly sample and process rocks in the field on Earth. The RASP allows geologists to surgically acquire samples of rock for later laboratory analysis. This tool, roughly the size of a wrench, allows the user to cut away swaths of weathering rinds, revealing pristine rock surfaces for observation and subsequent sampling with the same tool. RASPing deeper (.3.5 cm) exposes single rock strata in-situ. Where a geologist fs hammer can only expose unweathered layers of rock, the RASP can do the same, and then has the added ability to capture and process samples into powder with particle sizes less than 150 microns, making it easier for XRD/XRF (x-ray diffraction/x-ray fluorescence). The tool uses a rotating rasp bit (or two counter-rotating bits) that resides inside or above the catch container. The container has an open slot to allow the bit to extend outside the container and to allow cuttings to enter and be caught. When the slot and rasp bit are in contact with a substrate, the bit is plunged into it in a matter of seconds to reach pristine rock. A user in the field may sample a rock multiple times at multiple depths in minutes, instead of having to cut out huge, heavy rock samples for transport back to a lab for analysis. Because of the speed and accuracy of the RASP, hundreds of samples can be taken in one day. RASP-acquired samples are small and easily carried. A user can characterize more area in less time than by using conventional methods. The field-deployable RASP used a Ni

  10. SCAMPI: A code package for cross-section processing

    SciTech Connect

    Parks, C.V.; Petrie, L.M.; Bowman, S.M.; Broadhead, B.L.; Greene, N.M.; White, J.E.

    1996-04-01

    The SCAMPI code package consists of a set of SCALE and AMPX modules that have been assembled to facilitate user needs for preparation of problem-specific, multigroup cross-section libraries. The function of each module contained in the SCANTI code package is discussed, along with illustrations of their use in practical analyses. Ideas are presented for future work that can enable one-step processing from a fine-group, problem-independent library to a broad-group, problem-specific library ready for a shielding analysis.

  11. DOT-7A packaging test procedure

    SciTech Connect

    Kelly, D.L.

    1995-01-23

    This test procedure documents the steps involved with performance testing of Department of Transportation Specification 7A (DOT-7A) Type A packages. It includes description of the performance tests, the personnel involved, appropriate safety considerations, and the procedures to be followed while performing the tests. Westinghouse Hanford Company (WHC) is conducting the evaluation and testing discussed herein for the Department of Energy-Headquarters, Division of Quality Verification and Transportation Safety (EH-321). Please note that this report is not in WHC format. This report is being submitted through the Engineering Documentation System so that it may be used for reference and information purposes.

  12. Harsh-Environment Packaging for Downhole Gas and Oil Exploration

    SciTech Connect

    Shubhra Bansal; Junghyun Cho; Kevin Durocher; Chris Kapusta; Aaron Knobloch; David Shaddock; Harry Schoeller; Hua Xia

    2007-08-31

    This research into new packaging materials and methods for elevated temperatures and harsh environment electronics focused on gaining a basic understanding of current state-of-the-art in electronics packaging used in industry today, formulating the thermal-mechanical models of the material interactions and developing test structures to confirm these models. Discussions were initiated with the major General Electric (GE) businesses that currently sell into markets requiring high temperature electronics and packaging. They related the major modes of failure they encounter routinely and the hurdles needed to be overcome in order to improve the temperature specifications of these products. We consulted with our GE business partners about the reliability specifications and investigated specifications and guidelines that from IPC and the SAE body that is currently developing guidelines for electronics package reliability. Following this, a risk analysis was conducted for the program to identify the critical risks which need to be mitigated in order to demonstrate a flex-based packaging approach under these conditions. This process identified metal/polyimide adhesion, via reliability for flex substrates and high temperature interconnect as important technical areas for reliability improvement.

  13. The Affordance Template ROS Package for Robot Task Programming

    NASA Technical Reports Server (NTRS)

    Hart, Stephen; Dinh, Paul; Hambuchen, Kimberly

    2015-01-01

    This paper introduces the Affordance Template ROS package for quickly programming, adjusting, and executing robot applications in the ROS RViz environment. This package extends the capabilities of RViz interactive markers by allowing an operator to specify multiple end-effector waypoint locations and grasp poses in object-centric coordinate frames and to adjust these waypoints in order to meet the run-time demands of the task (specifically, object scale and location). The Affordance Template package stores task specifications in a robot-agnostic XML description format such that it is trivial to apply a template to a new robot. As such, the Affordance Template package provides a robot-generic ROS tool appropriate for building semi-autonomous, manipulation-based applications. Affordance Templates were developed by the NASA-JSC DARPA Robotics Challenge (DRC) team and have since successfully been deployed on multiple platforms including the NASA Valkyrie and Robonaut 2 humanoids, the University of Texas Dreamer robot and the Willow Garage PR2. In this paper, the specification and implementation of the affordance template package is introduced and demonstrated through examples for wheel (valve) turning, pick-and-place, and drill grasping, evincing its utility and flexibility for a wide variety of robot applications.

  14. 21 CFR 820.130 - Device packaging.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Device packaging. 820.130 Section 820.130 Food and... QUALITY SYSTEM REGULATION Labeling and Packaging Control § 820.130 Device packaging. Each manufacturer shall ensure that device packaging and shipping containers are designed and constructed to protect...

  15. Think INSIDE the Box: Package Engineering

    ERIC Educational Resources Information Center

    Snyder, Mark; Painter, Donna

    2014-01-01

    Most products people purchase, keep in their homes, and often discard, are typically packaged in some way. Packaging is so prevalent in daily lives that many of take it for granted. That is by design-the expectation of good packaging is that it exists for the sake of the product. The primary purposes of any package (to contain, inform, display,…

  16. 40 CFR 157.27 - Unit packaging.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Unit packaging. 157.27 Section 157.27 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS PACKAGING REQUIREMENTS FOR PESTICIDES AND DEVICES Child-Resistant Packaging § 157.27 Unit packaging. Pesticide...

  17. 49 CFR 173.29 - Empty packagings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Empty packagings. 173.29 Section 173.29... SHIPMENTS AND PACKAGINGS Preparation of Hazardous Materials for Transportation § 173.29 Empty packagings. (a) General. Except as otherwise provided in this section, an empty packaging containing only the residue of...

  18. 49 CFR 173.29 - Empty packagings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Empty packagings. 173.29 Section 173.29... SHIPMENTS AND PACKAGINGS Preparation of Hazardous Materials for Transportation § 173.29 Empty packagings. (a) General. Except as otherwise provided in this section, an empty packaging containing only the residue of...

  19. 21 CFR 820.130 - Device packaging.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Device packaging. 820.130 Section 820.130 Food and... QUALITY SYSTEM REGULATION Labeling and Packaging Control § 820.130 Device packaging. Each manufacturer shall ensure that device packaging and shipping containers are designed and constructed to protect...

  20. 40 CFR 157.27 - Unit packaging.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 25 2013-07-01 2013-07-01 false Unit packaging. 157.27 Section 157.27 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS PACKAGING REQUIREMENTS FOR PESTICIDES AND DEVICES Child-Resistant Packaging § 157.27 Unit packaging. Pesticide...

  1. 49 CFR 173.29 - Empty packagings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Empty packagings. 173.29 Section 173.29... SHIPMENTS AND PACKAGINGS Preparation of Hazardous Materials for Transportation § 173.29 Empty packagings. (a) General. Except as otherwise provided in this section, an empty packaging containing only the residue of...

  2. 40 CFR 157.27 - Unit packaging.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 24 2014-07-01 2014-07-01 false Unit packaging. 157.27 Section 157.27 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS PACKAGING REQUIREMENTS FOR PESTICIDES AND DEVICES Child-Resistant Packaging § 157.27 Unit packaging. Pesticide...

  3. 21 CFR 820.130 - Device packaging.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Device packaging. 820.130 Section 820.130 Food and... QUALITY SYSTEM REGULATION Labeling and Packaging Control § 820.130 Device packaging. Each manufacturer shall ensure that device packaging and shipping containers are designed and constructed to protect...

  4. 49 CFR 173.29 - Empty packagings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Empty packagings. 173.29 Section 173.29... SHIPMENTS AND PACKAGINGS Preparation of Hazardous Materials for Transportation § 173.29 Empty packagings. (a) General. Except as otherwise provided in this section, an empty packaging containing only the residue of...

  5. 40 CFR 157.27 - Unit packaging.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 25 2012-07-01 2012-07-01 false Unit packaging. 157.27 Section 157.27 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS PACKAGING REQUIREMENTS FOR PESTICIDES AND DEVICES Child-Resistant Packaging § 157.27 Unit packaging. Pesticide...

  6. 40 CFR 157.27 - Unit packaging.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Unit packaging. 157.27 Section 157.27 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS PACKAGING REQUIREMENTS FOR PESTICIDES AND DEVICES Child-Resistant Packaging § 157.27 Unit packaging. Pesticide...

  7. 49 CFR 173.29 - Empty packagings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Empty packagings. 173.29 Section 173.29... SHIPMENTS AND PACKAGINGS Preparation of Hazardous Materials for Transportation § 173.29 Empty packagings. (a) General. Except as otherwise provided in this section, an empty packaging containing only the residue of...

  8. Radioisotope thermoelectric generator transportation system safety analysis report for packaging. Volumes 1 and 2

    SciTech Connect

    Ferrell, P.C.

    1996-04-18

    This SARP describes the RTG Transportation System Package, a Type B(U) packaging system that is used to transport an RTG or similar payload. The payload, which is included in this SARP, is a generic, enveloping payload that specifically encompasses the General Purpose Heat Source (GPHS) RTG payload. The package consists of two independent containment systems mounted on a shock isolation transport skid and transported within an exclusive-use trailer.

  9. Material efficiency in Dutch packaging policy.

    PubMed

    Worrell, Ernst; van Sluisveld, Mariësse A E

    2013-03-13

    Packaging materials are one of the largest contributors to municipal solid waste generation. In this paper, we evaluate the material impacts of packaging policy in The Netherlands, focusing on the role of material efficiency (or waste prevention). Since 1991, five different policies have been implemented to reduce the environmental impact of packaging. The analysis shows that Dutch packaging policies helped to reduce the total packaging volume until 1999. After 2000, packaging consumption increased more rapidly than the baseline, suggesting that policy measures were not effective. Generally, we see limited attention to material efficiency to reduce packaging material use. For this purpose, we tried to gain more insight in recent activities on material efficiency, by building a database of packaging prevention initiatives. We identified 131 alterations to packaging implemented in the period 2005-2010, of which weight reduction was the predominant approach. More appropriate packaging policy is needed to increase the effectiveness of policies, with special attention to material efficiency. PMID:23359741

  10. Higher LPA2 and LPA6 mRNA Levels in Hepatocellular Carcinoma Are Associated with Poorer Differentiation, Microvascular Invasion and Earlier Recurrence with Higher Serum Autotaxin Levels.

    PubMed

    Enooku, Kenichiro; Uranbileg, Baasanjav; Ikeda, Hitoshi; Kurano, Makoto; Sato, Masaya; Kudo, Hiroki; Maki, Harufumi; Koike, Kazuhiko; Hasegawa, Kiyoshi; Kokudo, Norihiro; Yatomi, Yutaka

    2016-01-01

    Hepatocellular carcinoma (HCC) commonly develops in patients with liver fibrosis; in these patients, the blood levels of lysophosphatidic acid (LPA) and its generating enzyme autotaxin (ATX) increase with the liver fibrosis stage. We aimed to examine the potential relevance of ATX and LPA in HCC. Fifty-eight HCC patients who underwent surgical treatment were consecutively enrolled in the study. Among the LPA receptors in HCC, higher LPA2 mRNA levels correlated with poorer differentiation, and higher LPA6 mRNA levels correlated with microvascular invasion, which suggested a higher malignant potential of HCC with increased LPA2 and LPA6 expression. In patients with primary HCC, neither LPA2 nor LPA6 mRNA levels were associated with recurrence. However, when serum ATX levels were combined for analysis as a surrogate for plasma LPA levels, the cumulative intra-hepatic recurrence rate was higher in patients in whom both serum ATX levels and LPA2 or LPA6 mRNA levels were higher than the median. However, the mRNA level of phosphatidic acid-selective phospholipase A1ɑ, another LPA-generating enzyme, in HCC patients was not associated with pathological findings or recurrence, even in combination with the expression of LPA receptors. Higher LPA2 mRNA levels were associated with poorer differentiation, and higher LPA6 levels were associated with microvascular invasion in HCC; both became a risk factor for recurrence after surgical treatment when combined with increased serum ATX levels. ATX and LPA receptors merit consideration as therapeutic targets of HCC. PMID:27583415

  11. Temperature environment for 9975 packages stored in KAC

    SciTech Connect

    Daugherty, W. L.

    2015-09-10

    Plutonium materials are stored in the K Area Complex (KAC) in shipping packages, typically the 9975 shipping package. In order to estimate realistic degradation rates for components within the shipping package (i.e. the fiberboard overpack and O-ring seals), it is necessary to understand actual facility temperatures, which can vary daily and seasonally. Relevant facility temperature data available from several periods throughout its operating history have been reviewed. The annual average temperature within the Crane Maintenance Area has ranged from approximately 70 to 74 °F, although there is significant seasonal variation and lesser variation among different locations within the facility. The long-term average degradation rate for 9975 package components is very close to that expected if the component were to remain continually at the annual average temperature. This result remains valid for a wide range of activation energies (which describes the variation in degradation rate as the temperature changes), if the activation energy remains constant over the seasonal range of component temperatures. It is recommended that component degradation analyses and service life estimates incorporate these results. Specifically, it is proposed that future analyses assume an average facility ambient air temperature of 94 °F. This value is bounding for all packages, and includes margin for several factors such as increased temperatures within the storage arrays, the addition of more packages in the future, and future operational changes.

  12. Industrial packaging and assembly infrastructure for MOEMS

    NASA Astrophysics Data System (ADS)

    van Heeren, Henne

    2004-01-01

    , packaging and assembly is from nature application specific and solutions found are not always transferable from one product to another. But designers can often benefit from experience from other and general available technologies. A number of companies offer packaging and assembly services for MEMS/MST and this report give typical examples of those commercial services. The companies range from small start-ups, offering very specialized services, to large semiconductor packaging companies, having production lines for microsystem based products. Selecting the proper packaging method may tip the scales towards a product success or towards a product failure, while it nearly always present s a substantial part of the cost of the product. This is therefore is not a marginal concern, but a crucial part of the product design. The presentation will also address mayor trends and technologies. Finally, the article provides sufficient levels of classification and categorisation for various aspects for the technologies, in specific, and the industry, in general, to provide particularly useful insights into the activities and the developments in this market. With over 50 companies studied and assessed, it provides an up to date account of the state of this business and its future potential.

  13. Innovative and Improved Efficiency on the Design of a control System SOftware for CBSS 6m Radio Telescope using LabView in Nigeria

    NASA Astrophysics Data System (ADS)

    EKEOMA Opara, Fidelis

    2015-08-01

    Software has been provided for controlling the antenna and selection of sources in a 6m radio telescope. In this work the most challenging aspect is the maintainance of the pointing accuracy of the final structure with pointing tolerance of about 0.0003 or 1 arcsecond. Using LabView, the voltage through the I/Q is read with a DAQ virtual instrument. The values are then calculated with the dish at its zero position, hence the control system is fully implemented and tested to work at full efficiency.

  14. Design of a 0. 6-m bore wind-and-react 12-T, 6-kA, Nb sub 3 Sn magnet

    SciTech Connect

    della Corte, A.; Di Pietro, E.; Pasotti, G.; Sacchetti, N.; Spadoni, M. )

    1991-03-01

    This paper presents the design concepts of a Nb{sub 3}Sn wind-and-react (W/R) magnet, wound with a cable-in-conduit (CIC) conductor. The magnet is designed to operate at approximately 6 kA, generating a maximum field of 12 T over a 0.6-m bore. The design of the forced-flow-cooled cable-in-conduit conductor, the winding principles, the heat exchanger effect in the magnet, and the stress analysis on the coil and conductor are reported and discussed.

  15. Method for Determining Optimal Residential Energy Efficiency Retrofit Packages

    SciTech Connect

    Polly, B.; Gestwick, M.; Bianchi, M.; Anderson, R.; Horowitz, S.; Christensen, C.; Judkoff, R.

    2011-04-01

    Businesses, government agencies, consumers, policy makers, and utilities currently have limited access to occupant-, building-, and location-specific recommendations for optimal energy retrofit packages, as defined by estimated costs and energy savings. This report describes an analysis method for determining optimal residential energy efficiency retrofit packages and, as an illustrative example, applies the analysis method to a 1960s-era home in eight U.S. cities covering a range of International Energy Conservation Code (IECC) climate regions. The method uses an optimization scheme that considers average energy use (determined from building energy simulations) and equivalent annual cost to recommend optimal retrofit packages specific to the building, occupants, and location. Energy savings and incremental costs are calculated relative to a minimum upgrade reference scenario, which accounts for efficiency upgrades that would occur in the absence of a retrofit because of equipment wear-out and replacement with current minimum standards.

  16. 49 CFR 173.24 - General requirements for packagings and packages.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ..., packaging compatibility, etc. must be maintained for the minimum and maximum temperatures, changes in... increase of heat or pressure, significantly reduce the effectiveness of the packaging; (4) There will be no... packagings. A packaging is authorized for a hazardous material only if— (1) The packaging is prescribed...

  17. Package inspection using inverse diffraction

    NASA Astrophysics Data System (ADS)

    McAulay, Alastair D.

    2008-08-01

    More efficient cost-effective hand-held methods of inspecting packages without opening them are in demand for security. Recent new work in TeraHertz sources,1 millimeter waves, presents new possibilities. Millimeter waves pass through cardboard and styrofoam, common packing materials, and also pass through most materials except those with high conductivity like metals which block light and are easily spotted. Estimating refractive index along the path of the beam through the package from observations of the beam passing out of the package provides the necessary information to inspect the package and is a nonlinear problem. So we use a generalized linear inverse technique that we first developed for finding oil by reflection in geophysics.2 The computation assumes parallel slices in the packet of homogeneous material for which the refractive index is estimated. A beam is propagated through this model in a forward computation. The output is compared with the actual observations for the package and an update computed for the refractive indices. The loop is repeated until convergence. The approach can be modified for a reflection system or to include estimation of absorption.

  18. The reduction of packaging waste

    SciTech Connect

    Raney, E.A.; Hogan, J.J.; McCollom, M.L.; Meyer, R.J.

    1994-04-01

    Nationwide, packaging waste comprises approximately one-third of the waste disposed in sanitary landfills. the US Department of Energy (DOE) generated close to 90,000 metric tons of sanitary waste. With roughly one-third of that being packaging waste, approximately 30,000 metric tons are generated per year. The purpose of the Reduction of Packaging Waste project was to investigate opportunities to reduce this packaging waste through source reduction and recycling. The project was divided into three areas: procurement, onsite packaging and distribution, and recycling. Waste minimization opportunities were identified and investigated within each area, several of which were chosen for further study and small-scale testing at the Hanford Site. Test results, were compiled into five ``how-to`` recipes for implementation at other sites. The subject of the recipes are as follows: (1) Vendor Participation Program; (2) Reusable Containers System; (3) Shrink-wrap System -- Plastic and Corrugated Cardboard Waste Reduction; (4) Cardboard Recycling ; and (5) Wood Recycling.

  19. Reference waste package environment report

    SciTech Connect

    Glassley, W.E.

    1986-10-01

    One of three candidate repository sites for high-level radioactive waste packages is located at Yucca Mountain, Nevada, in rhyolitic tuff 700 to 1400 ft above the static water table. Calculations indicate that the package environment will experience a maximum temperature of {similar_to}230{sup 0}C at 9 years after emplacement. For the next 300 years the rock within 1 m of the waste packages will remain dehydrated. Preliminary results suggest that the waste package radiation field will have very little effect on the mechanical properties of the rock. Radiolysis products will have a negligible effect on the rock even after rehydration. Unfractured specimens of repository rock show no change in hydrologic characteristics during repeated dehydration-rehydration cycles. Fractured samples with initially high permeabilities show a striking permeability decrease during dehydration-rehydration cycling, which may be due to fracture healing via deposition of silica. Rock-water interaction studies demonstrate low and benign levels of anions and most cations. The development of sorptive secondary phases such as zeolites and clays suggests that anticipated rock-water interaction may produce beneficial changes in the package environment.

  20. The Assurance Challenges of Advanced Packaging Technologies for Electronics

    NASA Technical Reports Server (NTRS)

    Sampson, Michael J.

    2010-01-01

    Advances in microelectronic parts performance are driving towards finer feature sizes, three-dimensional geometries and ever-increasing number of transistor equivalents that are resulting in increased die sizes and interconnection (I/O) counts. The resultant packaging necessary to provide assemble-ability, environmental protection, testability and interconnection to the circuit board for the active die creates major challenges, particularly for space applications, Traditionally, NASA has used hermetically packaged microcircuits whenever available but the new demands make hermetic packaging less and less practical at the same time as more and more expensive, Some part types of great interest to NASA designers are currently only available in non-hermetic packaging. It is a far more complex quality and reliability assurance challenge to gain confidence in the long-term survivability and effectiveness of nonhermetic packages than for hermetic ones. Although they may provide more rugged environmental protection than the familiar Plastic Encapsulated Microcircuits (PEMs), the non-hermetic Ceramic Column Grid Array (CCGA) packages that are the focus of this presentation present a unique combination of challenges to assessing their suitability for spaceflight use. The presentation will discuss the bases for these challenges, some examples of the techniques proposed to mitigate them and a proposed approach to a US MIL specification Class for non-hermetic microcircuits suitable for space application, Class Y, to be incorporated into M. IL-PRF-38535. It has recently emerged that some major packaging suppliers are offering hermetic area array packages that may offer alternatives to the nonhermetic CCGA styles but have also got their own inspectability and testability issues which will be briefly discussed in the presentation,

  1. The Viral DNA Packaging Motor of Bacteriophage Lambda

    NASA Astrophysics Data System (ADS)

    Catalano, Carlos E.

    2007-03-01

    Terminase enzymes are common to both eukaryotic and prokaryotic double-stranded DNA viruses. These enzymes, which serve as molecular motors that selectively ``package'' viral DNA into a pre-formed procapsid structure, are among the most powerful biological motors characterized to date. Bacteriophage lambda terminase is a heteroligomer composed of gpA and gpNu1 subunits. The smaller gpNu1 subunit is required for specific recognition of viral DNA, a process that is modulated by ATP. The gpA subunit possesses site-specific nuclease and helicase activities that ``mature'' the viral genome prior to packaging. The subunit further possesses a DNA translocase activity that is central to the packaging motor complex. Discrete ATPase sites in gpA modulate the DNA maturation reactions and fuel the DNA packaging reaction. Kinetic characterization of lambda terminase indicates significant interaction between the multiple catalytic sites of the enzyme and has led to a minimal kinetic model describing the assembly of a catalytically-competent packaging motor complex. Biophysical studies demonstrate that purified lambda terminase forms a homogenous, heterotrimeric structure consisting of one gpA subunit in association with two gpNu1 proteins. Four heterotrimers further assemble into a ring-like structure of sufficient size to encircle duplex DNA. The ensemble of data suggests that the ring tetramer represents the biologically relevant, catalytically-competent motor complex responsible for genome processing and packaging reactions. We present a model for the functional DNA packaging motor complex that finds general utility in our global understanding of the enzymology of virus assembly.

  2. Implications of light energy on food quality and packaging selection.

    PubMed

    Duncan, Susan E; Chang, Hao-Hsun

    2012-01-01

    Light energy in the ultraviolet and visible light regions plays a critical role in overall food quality, leading to various degradation and oxidation reactions. Food degradation and oxidation result in the destruction of nutrients and bioactive compounds, the formation of off odors and flavors, the loss of food color, and the formation of toxic substances. Food compounds are sensitive to various light wavelengths. Understanding the effect that specific light wavelengths have on food compounds will allow the development of novel food packaging materials that block the most damaging light wavelengths to photostability of specific food compounds. Future research should focus more specifically on the effect of specific light wavelengths on the quality of specific food products, as there is limited published information on this particular topic. This information also can be directly related to the selection of food packaging materials to retain both high quality and visual clarity of food products exposed to light. PMID:23034114

  3. Review: nanocomposites in food packaging.

    PubMed

    Arora, Amit; Padua, G W

    2010-01-01

    The development of nanocomposites is a new strategy to improve physical properties of polymers, including mechanical strength, thermal stability, and gas barrier properties. The most promising nanoscale size fillers are montmorillonite and kaolinite clays. Graphite nanoplates are currently under study. In food packaging, a major emphasis is on the development of high barrier properties against the migration of oxygen, carbon dioxide, flavor compounds, and water vapor. Decreasing water vapor permeability is a critical issue in the development of biopolymers as sustainable packaging materials. The nanoscale plate morphology of clays and other fillers promotes the development of gas barrier properties. Several examples are cited. Challenges remain in increasing the compatibility between clays and polymers and reaching complete dispersion of nanoplates. Nanocomposites may advance the utilization of biopolymers in food packaging. PMID:20492194

  4. Mixed Oxide Fresh Fuel Package Auxiliary Equipment

    SciTech Connect

    Yapuncich, F.; Ross, A.; Clark, R.H.; Ammerman, D.

    2008-07-01

    The United States Department of Energy's National Nuclear Security Administration (NNSA) is overseeing the construction the Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF) on the Savannah River Site. The new facility, being constructed by NNSA's contractor Shaw AREVA MOX Services, will fabricate fuel assemblies utilizing surplus plutonium as feedstock. The fuel will be used in designated commercial nuclear reactors. The MOX Fresh Fuel Package (MFFP), which has recently been licensed by the Nuclear Regulatory Commission (NRC) as a type B package (USA/9295/B(U)F-96), will be utilized to transport the fabricated fuel assemblies from the MFFF to the nuclear reactors. It was necessary to develop auxiliary equipment that would be able to efficiently handle the high precision fuel assemblies. Also, the physical constraints of the MFFF and the nuclear power plants require that the equipment be capable of loading and unloading the fuel assemblies both vertically and horizontally. The ability to reconfigure the load/unload evolution builds in a large degree of flexibility for the MFFP for the handling of many types of both fuel and non fuel payloads. The design and analysis met various technical specifications including dynamic and static seismic criteria. The fabrication was completed by three major fabrication facilities within the United States. The testing was conducted by Sandia National Laboratories. The unique design specifications and successful testing sequences will be discussed. (authors)

  5. Structure and properties of dies obtained from scrap of 5KhNM and R6M5 steels by electroslag remelting

    SciTech Connect

    Timchenko, E.I.; Semenova, L.M.; Berezkin, Yu.A.; Zaitseva, I.D.

    1987-11-01

    It is known that in a number of cases cast dies of tool steels for hot working possess increased life. In the Lozovaya Forging and Machining Plant in electroslag remelting (ESR) of worn dies, a method is used making it possible to improve the quality of the cast blanks (dies) by additional alloying of them. A consumable composite electrode made of worn dies of 5KhNM steel reforged into bars and butt welded and scrap of R6M5 tool steel welded along the whole length of the main electrode in the form of a solid bar is used. Practically none of the chromium, molybdenum, tungsten, and vanadium additionally added in electroslag remelting burns off and therefore it is sufficient to add the expensive R6M5 steel scrap once. The improved characteristics of the steel are maintained in subsequent operations in the production chain. A comparative investigation was made of the character of the structure in the as-cast, annealed, hardened, and tempered conditions of 5KhNMVF steel produced by the above method and of 5KhNM steel produced by different methods.

  6. 49 CFR 173.62 - Specific packaging requirements for explosives.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... List of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and at... paper, kraft paper, waxed steel (4A).aluminum (4B). other metal (4N). natural wood, ordinary (4C1... resistant paper, waxed plastics Not necessary Bags.woven plastics (5H1/2/3). paper, multiwall,...

  7. Health Instruction Packages: Nursing--Specific Diseases and Disorders.

    ERIC Educational Resources Information Center

    Curran, Fern A.; And Others

    Text, illustrations, and exercises are utilized in this set of learning modules to instruct nurses and other health care professionals in the symptoms and treatment of common medical disorders. The first module, by Fern A. Curran, discusses the causes of decubitus ulcers (i.e., bedsores), the physical damage they can do, and methods of preventing…

  8. 49 CFR 173.62 - Specific packaging requirements for explosives.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... citations affecting § 173.62, see the List of CFR Sections Affected, which appears in the Finding Aids... development, quality control, or as a commercial sample. Explosive samples which are wetted or desensitized.... A jet perforating gun, charged, oil well may be transported under the following conditions:...

  9. 49 CFR 173.62 - Specific packaging requirements for explosives.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Federal Register citations affecting § 173.62, see the List of CFR Sections Affected, which appears in the..., quality control, or as a commercial sample. Explosive samples which are wetted or desensitized must be... or 1H2). plywood (1D). US 1 1. A jet perforating gun, charged, oil well may be transported under...

  10. An Arbitrary Precision Computation Package

    2003-06-14

    This package permits a scientist to perform computations using an arbitrarily high level of numeric precision (the equivalent of hundreds or even thousands of digits), by making only minor changes to conventional C++ or Fortran-90 soruce code. This software takes advantage of certain properties of IEEE floating-point arithmetic, together with advanced numeric algorithms, custom data types and operator overloading. Also included in this package is the "Experimental Mathematician's Toolkit", which incorporates many of these facilitiesmore » into an easy-to-use interactive program.« less

  11. GNS-12 Packaging design criteria

    SciTech Connect

    Clements, E.P., Westinghouse Hanford

    1996-07-24

    The purpose of this Packaging Design Criteria (PDC) is to provide criteria for the Safety Analysis Report for Packaging (SARP)(Onsite). The SARP provides the evaluation to demonstrate that the onsite transportation safety criteria are met for the transport and storage of the 324 Building vitrified encapsulated material in the GNS-12 cask. In this application, the approved PDC provides a formal set of standards for the payload requirements, and guidance for the current cask transport configuration and a revised storage seal and primary lid modification design.

  12. Truss Performance and Packaging Metrics

    NASA Technical Reports Server (NTRS)

    Mikulas, Martin M.; Collins, Timothy J.; Doggett, William; Dorsey, John; Watson, Judith

    2006-01-01

    In the present paper a set of performance metrics are derived from first principals to assess the efficiency of competing space truss structural concepts in terms of mass, stiffness, and strength, for designs that are constrained by packaging. The use of these performance metrics provides unique insight into the primary drivers for lowering structural mass and packaging volume as well as enabling quantitative concept performance evaluation and comparison. To demonstrate the use of these performance metrics, data for existing structural concepts are plotted and discussed. Structural performance data is presented for various mechanical deployable concepts, for erectable structures, and for rigidizable structures.

  13. Staphylococcal pathogenicity island DNA packaging system involving cos-site packaging and phage-encoded HNH endonucleases

    PubMed Central

    Quiles-Puchalt, Nuria; Carpena, Nuria; Alonso, Juan C.; Novick, Richard P.; Marina, Alberto; Penadés, José R.

    2014-01-01

    Staphylococcal pathogenicity islands (SaPIs) are the prototypical members of a widespread family of chromosomally located mobile genetic elements that contribute substantially to intra- and interspecies gene transfer, host adaptation, and virulence. The key feature of their mobility is the induction of SaPI excision and replication by certain helper phages and their efficient encapsidation into phage-like infectious particles. Most SaPIs use the headful packaging mechanism and encode small terminase subunit (TerS) homologs that recognize the SaPI-specific pac site and determine SaPI packaging specificity. Several of the known SaPIs do not encode a recognizable TerS homolog but are nevertheless packaged efficiently by helper phages and transferred at high frequencies. In this report, we have characterized one of the non–terS-coding SaPIs, SaPIbov5, and found that it uses two different, undescribed packaging strategies. SaPIbov5 is packaged in full-sized phage-like particles either by typical pac-type helper phages, or by cos-type phages—i.e., it has both pac and cos sites—a configuration that has not hitherto been described for any mobile element, phages included—and uses the two different phage-coded TerSs. To our knowledge, this is the first example of SaPI packaging by a cos phage, and in this, it resembles the P4 plasmid of Escherichia coli. Cos-site packaging in Staphylococcus aureus is additionally unique in that it requires the HNH nuclease, carried only by cos phages, in addition to the large terminase subunit, for cos-site cleavage and melting. PMID:24711396

  14. Package for integrated optic circuit and method

    DOEpatents

    Kravitz, S.H.; Hadley, G.R.; Warren, M.E.; Carson, R.F.; Armendariz, M.G.

    1998-08-04

    A structure and method are disclosed for packaging an integrated optic circuit. The package comprises a first wall having a plurality of microlenses formed therein to establish channels of optical communication with an integrated optic circuit within the package. A first registration pattern is provided on an inside surface of one of the walls of the package for alignment and attachment of the integrated optic circuit. The package in one embodiment may further comprise a fiber holder for aligning and attaching a plurality of optical fibers to the package and extending the channels of optical communication to the fibers outside the package. In another embodiment, a fiber holder may be used to hold the fibers and align the fibers to the package. The fiber holder may be detachably connected to the package. 6 figs.

  15. Package for integrated optic circuit and method

    DOEpatents

    Kravitz, Stanley H.; Hadley, G. Ronald; Warren, Mial E.; Carson, Richard F.; Armendariz, Marcelino G.

    1998-01-01

    A structure and method for packaging an integrated optic circuit. The package comprises a first wall having a plurality of microlenses formed therein to establish channels of optical communication with an integrated optic circuit within the package. A first registration pattern is provided on an inside surface of one of the walls of the package for alignment and attachment of the integrated optic circuit. The package in one embodiment may further comprise a fiber holder for aligning and attaching a plurality of optical fibers to the package and extending the channels of optical communication to the fibers outside the package. In another embodiment, a fiber holder may be used to hold the fibers and align the fibers to the package. The fiber holder may be detachably connected to the package.

  16. MEMS Packaging and Thermal Issues in Reliability

    NASA Astrophysics Data System (ADS)

    Cheng, Yu-Ting; Lin, Liwei

    The potential of MEMS/NEMS technologies has been viewed as a comparable or even bigger revolution than that of microelectronics. These scientific and engineering advancements in MEMS/NEMS could bring applications to reality previously unthinkable, from space systems, environmental instruments, to daily life appliances. As presented in previous chapters, the development of core MEMS/NEMS processes has already demonstrated a lot of commercial applications as well as future potentials with elaborated functionalities. However, a low cost and reliable package for the protection of these MEMS/NEMS products is still a very difficult task. Without addressing the packaging and reliability issues, no commercial products can be sold on the market. Packaging design and modeling, packaging material selection, packaging process integration, and packaging cost are main issues to be considered when developing a new MEMS packaging process. In this chapter, we will present the fundamentals of MEMS/NEMS packaging technology, including packaging processes, hermetic and vacuum encapsulations, thermal issues, packaging reliability, and future packaging trends. The future development of MEMS packaging will rely on the success of the implementation of several unique techniques, such as packaging design kits for system and circuit designer, low cost and high yield wafer level, chip-scale packaging techniques, effective testing techniques at the wafer-level to reduce overall testing costs; and reliable fabrication of an interposer [37.1] with vertical through-interconnects for device integrations.

  17. 49 CFR 173.415 - Authorized Type A packages.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... fissile materials in 10 CFR part 71 and is used in accordance with § 173.471. (c) Any Type B(U) or Type B... least one year after the latest shipment, and shall provide to DOT on request, complete documentation of... of a Specification 7A package must maintain on file for at least two years after the offeror's...

  18. 49 CFR 178.3 - Marking of packagings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... this part, with the name and address or symbol of the packaging manufacturer or, where specifically authorized, the symbol of the approval agency certifying compliance with a UN standard. Symbols, if...

  19. Health Care Reform: Designing the Standard Benefits Package.

    ERIC Educational Resources Information Center

    McArdle, Frank B.

    1994-01-01

    Considerations in designing a standard health care benefits package as a part of national health care reform are discussed. Specific features examined include deductibles, employer contributions, regional variations, cost management techniques such as managed care and higher copayments, annual out-of-pocket maximums, and lifetime benefit maximums.…

  20. Data aNd Computation Reordering package using temporal and spatial hypergraphs

    2004-08-01

    A package for experimentation with data and computation reordering algorithms. One can input various file formats representing sparse matrices, reorder data, and computation through the specification of command line parameters, and time benchmark computations that use the new data and computation ordering. The package includes existing reordering algorithms and new ones introduced by the authors based on the temporal and spatial locality hypergraph model.

  1. 49 CFR 178.925 - Standards for rigid plastic Large Packagings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... solids. Rigid plastic Large Packaging types are designated: (1) 50H rigid plastics. (2) (b) A rigid plastic Large Packaging must be manufactured from plastic material of known specifications and be of a... additives must be compatible with the contents and remain effective throughout the life of the plastic...

  2. Child-Resistant Packaging for E-Liquid: A Review of US State Legislation.

    PubMed

    Frey, Leslie T; Tilburg, William C

    2016-02-01

    A growing number of states have introduced or enacted legislation requiring child-resistant packaging for e-liquid containers; however, these laws involve varying terms, packaging standards, and enforcement provisions, raising concerns about their effectiveness. We evaluated bills against 4 benchmarks: broad product definitions that contemplate future developments in the market, citations to a specific packaging standard, stated penalties for violations, and express grants of authority to a state entity to enforce the packaging requirements. Our findings showed that 3 states meet all 4 benchmarks in their enacted legislation. We encourage states to consider these benchmarks when revising statutes or drafting future legislation. PMID:26691114

  3. Spent nuclear fuel project product specification

    SciTech Connect

    Pajunen, A.L.

    1998-01-30

    Product specifications are limits and controls established for each significant parameter that potentially affects safety and/or quality of the Spent Nuclear Fuel (SNF) packaged for transport to dry storage. The product specifications in this document cover the spent fuel packaged in MultiCanister Overpacks (MCOs) to be transported throughout the SNF Project. The SNF includes N Reactor fuel and single-pass reactor fuel. The FRS removes the SNF from the storage canisters, cleans it, and places it into baskets. The MCO loading system places the baskets into MCO/Cask assembly packages. These packages are then transferred to the Cold Vacuum Drying (CVD) Facility. After drying at the CVD Facility, the MCO cask packages are transferred to the Canister Storage Building (CSB), where the MCOs are removed from the casks, staged, inspected, sealed (by welding), and stored until a suitable permanent disposal option is implemented. The key criteria necessary to achieve these goals are documented in this specification.

  4. A Computerized Petroleum Geology Package.

    ERIC Educational Resources Information Center

    Moser, Louise E.

    1983-01-01

    Describes a package of computer programs developed to implement an oil exploration game that gives undergraduate students practical experience in applying theoretical principles of petroleum geology. The programs facilitate management of the game by the instructor and enhance the learning experience. (Author/MBR)

  5. COLDMON -- Cold File Analysis Package

    NASA Astrophysics Data System (ADS)

    Rawlinson, D. J.

    The COLDMON package has been written to allow system managers to identify those items of software that are not used (or used infrequently) on their systems. It consists of a few command procedures and a Fortran program to analyze the results. It makes use of the AUDIT facility and security ACLs in VMS.

  6. The Macro - Games Course Package.

    ERIC Educational Resources Information Center

    Heriot-Watt Univ., Edinburgh (Scotland). Esmee Fairbairn Economics Research Centre.

    Part of an Economic Education Series, the course package is designed to teach basic concepts and fundamental principles of macroeconomics and how they can be applied to various world problems. For use with college students, learning is gained through lectures, discussion, simulation games, programmed learning, and text. Time allotment is a 15-week…

  7. DATACUBE: A datacube manipulation package

    NASA Astrophysics Data System (ADS)

    Allan, Alasdair; Currie, Malcolm J.

    2014-05-01

    DATACUBE is a command-line package for manipulating and visualizing data cubes. It was designed for integral field spectroscopy but has been extended to be a generic data cube tool, used in particular for sub-millimeter data cubes from the James Clerk Maxwell Telescope. It is part of the Starlink software collection (ascl:1110.012).

  8. Food Nanotechnology: Food Packaging Applications

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Astonishing growth in the market for nanofoods is predicted in the future, from the current market of $2.6 billion to $20.4 billion in 2010. The market for nanotechnology in food packaging alone is expected to reach $360 million in 2008. In large part the impetus for this predicted growth is the e...

  9. Electronic Spreadsheet Packages for Microcomputers.

    ERIC Educational Resources Information Center

    Gibson, Larry M.

    1984-01-01

    Describes capabilities and advantages of spreadsheet software, including its ability to perform "what-if" analysis quickly and easily. Also noted are additional advantages; applications, including use in the library environment; history and development; new-generation spreadsheets; and enhanced packaging in the near future. A spreadsheet software…

  10. RAGG - R EPISODIC AGGREGATION PACKAGE

    EPA Science Inventory

    The RAGG package is an R implementation of the CMAQ episodic model aggregation method developed by Constella Group and the Environmental Protection Agency. RAGG is a tool to provide climatological seasonal and annual deposition of sulphur and nitrogen for multimedia management. ...

  11. Food Nanotechnology - Food Packaging Applications

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Astonishing growth in the market for nanofoods is predicted in the future, from the current market of $2.6 billion to $20.4 billion in 2010. The market for nanotechnology in food packaging alone is expected to reach $360 million in 2008. In large part, the impetus for this predicted growth is the ...

  12. Comparison of different LED Packages

    NASA Astrophysics Data System (ADS)

    Dieker, Henning; Miesner, Christian; Püttjer, Dirk; Bachl, Bernhard

    2007-09-01

    In this paper different technologies for LED packaging are compared, focusing on Chip on Board (COB) and SMD technology. The package technology which is used depends on the LED application. A critical fact in LED technology is the thermal management, especially for high brightness LED applications because the thermal management is important for reliability, lifetime and electrooptical performance of the LED module. To design certain and long life LED applications knowledge of the heat flow from LEDs to the complete application is required. High sophisticated FEM simulations are indispensable for modern development of high power LED applications. We compare simulations of various substrate materials and packaging technologies simulated using FLOTHERM software. Thereby different substrates such as standard FR4, ceramic and metal core printed circuit boards are considered. For the verification of the simulated results and the testing of manufactured modules, advanced measurement tools are required. We show different ways to experimentally characterize the thermal behavior of LED modules. The thermal path is determined by the transient thermal analysis using the MicReD T3Ster analyzer. Afterwards it will be compared to the conventional method using thermocouples. The heat distribution over the module is investigated by an IR-Camera. We demonstrate and compare simulation and measurement results of Chip-on-Board (COB) and Sub-Mounted Devices (SMD) technology. The results reveal that for different applications certain packages are ideal.

  13. Spent nuclear fuel project product specification

    SciTech Connect

    PAJUNEN, A.L.

    1999-02-25

    This document establishes the limits and controls for the significant parameters that could potentially affect the safety and/or quality of the Spent Nuclear Fuel (SNF) packaged for processing, transport, and storage. The product specifications in this document cover the SNF packaged in Multi-Canister Overpacks to be transported throughout the SNF Project.

  14. Spent Nuclear Fuel (SNF) Project Product Specification

    SciTech Connect

    PAJUNEN, A.L.

    2000-01-20

    This document establishes the limits and controls for the significant parameters that could potentially affect the safety and/or quality of the Spent Nuclear Fuel (SNF) packaged for processing, transport, and storage. The product specifications in this document cover the SNF packaged in Multi-Canister Overpacks to be transported throughout the SNF Project.

  15. 16 CFR 1702.11 - Product specifications.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Product specifications. 1702.11 Section 1702.11 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION POISON PREVENTION PACKAGING ACT OF 1970 REGULATIONS PETITIONS FOR EXEMPTIONS FROM POISON PREVENTION PACKAGING ACT REQUIREMENTS; PETITION...

  16. 16 CFR 1702.11 - Product specifications.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Product specifications. 1702.11 Section 1702.11 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION POISON PREVENTION PACKAGING ACT OF 1970 REGULATIONS PETITIONS FOR EXEMPTIONS FROM POISON PREVENTION PACKAGING ACT REQUIREMENTS; PETITION...

  17. 16 CFR 1702.11 - Product specifications.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Product specifications. 1702.11 Section 1702.11 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION POISON PREVENTION PACKAGING ACT OF 1970 REGULATIONS PETITIONS FOR EXEMPTIONS FROM POISON PREVENTION PACKAGING ACT REQUIREMENTS; PETITION...

  18. 16 CFR 1702.11 - Product specifications.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Product specifications. 1702.11 Section 1702.11 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION POISON PREVENTION PACKAGING ACT OF 1970 REGULATIONS PETITIONS FOR EXEMPTIONS FROM POISON PREVENTION PACKAGING ACT REQUIREMENTS; PETITION...

  19. Packaging Technology Developed for High-Temperature Silicon Carbide Microsystems

    NASA Technical Reports Server (NTRS)

    Chen, Liang-Yu; Hunter, Gary W.; Neudeck, Philip G.

    2001-01-01

    High-temperature electronics and sensors are necessary for harsh-environment space and aeronautical applications, such as sensors and electronics for space missions to the inner solar system, sensors for in situ combustion and emission monitoring, and electronics for combustion control for aeronautical and automotive engines. However, these devices cannot be used until they can be packaged in appropriate forms for specific applications. Suitable packaging technology for operation temperatures up to 500 C and beyond is not commercially available. Thus, the development of a systematic high-temperature packaging technology for SiC-based microsystems is essential for both in situ testing and commercializing high-temperature SiC sensors and electronics. In response to these needs, researchers at Glenn innovatively designed, fabricated, and assembled a new prototype electronic package for high-temperature electronic microsystems using ceramic substrates (aluminum nitride and aluminum oxide) and gold (Au) thick-film metallization. Packaging components include a ceramic packaging frame, thick-film metallization-based interconnection system, and a low electrical resistance SiC die-attachment scheme. Both the materials and fabrication process of the basic packaging components have been tested with an in-house-fabricated SiC semiconductor test chip in an oxidizing environment at temperatures from room temperature to 500 C for more than 1000 hr. These test results set lifetime records for both high-temperature electronic packaging and high-temperature electronic device testing. As required, the thick-film-based interconnection system demonstrated low (2.5 times of the room-temperature resistance of the Au conductor) and stable (decreased 3 percent in 1500 hr of continuous testing) electrical resistance at 500 C in an oxidizing environment. Also as required, the electrical isolation impedance between printed wires that were not electrically joined by a wire bond remained high

  20. A survey of packages for large linear systems

    SciTech Connect

    Wu, Kesheng; Milne, Brent

    2000-02-11

    This paper evaluates portable software packages for the iterative solution of very large sparse linear systems on parallel architectures. While we cannot hope to tell individual users which package will best suit their needs, we do hope that our systematic evaluation provides essential unbiased information about the packages and the evaluation process may serve as an example on how to evaluate these packages. The information contained here include feature comparisons, usability evaluations and performance characterizations. This review is primarily focused on self-contained packages that can be easily integrated into an existing program and are capable of computing solutions to very large sparse linear systems of equations. More specifically, it concentrates on portable parallel linear system solution packages that provide iterative solution schemes and related preconditioning schemes because iterative methods are more frequently used than competing schemes such as direct methods. The eight packages evaluated are: Aztec, BlockSolve,ISIS++, LINSOL, P-SPARSLIB, PARASOL, PETSc, and PINEAPL. Among the eight portable parallel iterative linear system solvers reviewed, we recommend PETSc and Aztec for most application programmers because they have well designed user interface, extensive documentation and very responsive user support. Both PETSc and Aztec are written in the C language and are callable from Fortran. For those users interested in using Fortran 90, PARASOL is a good alternative. ISIS++is a good alternative for those who prefer the C++ language. Both PARASOL and ISIS++ are relatively new and are continuously evolving. Thus their user interface may change. In general, those packages written in Fortran 77 are more cumbersome to use because the user may need to directly deal with a number of arrays of varying sizes. Languages like C++ and Fortran 90 offer more convenient data encapsulation mechanisms which make it easier to implement a clean and intuitive user