Science.gov

Sample records for 6th regular inspection

  1. Regularization approach for tomosynthesis X-ray inspection

    SciTech Connect

    Tigkos, Konstantinos; Hassler, Ulf; Holub, Wolfgang; Woerlein, Norbert; Rehak, Markus

    2014-02-18

    X-ray inspection is intended to be used as an escalation technique for inspection of carbon fiber reinforced plastics (CFRP) in aerospace applications, especially in case of unclear indications from ultrasonic or other NDT modalities. Due to their large dimensions, most aerospace components cannot be scanned by conventional computed tomography. In such cases, X-ray Laminography may be applied, allowing a pseudo 3D slice-by-slice reconstruction of the sample with Tomosynthesis. However, due to the limited angle acquisition geometry, reconstruction artifacts arise, especially at surfaces parallel to the imaging plane. To regularize the Tomosynthesis approach, we propose an additional prescan of the object to detect outer sample surfaces. We recommend the use of contrasted markers which are temporarily attached to the sample surfaces. The depth position of the markers is then derived from that prescan. As long as the sample surface remains simple, few markers are required to fit the respective object surfaces. The knowledge about this surface may then be used to regularize the final Tomosynthesis reconstruction, performed with markerless projections. Eventually, it can also serve as prior information for an ART reconstruction or to register a CAD model of the sample. The presented work is carried out within the European FP7 project QUICOM. We demonstrate the proposed approach within a simulation study applying an acquisition geometry suited for CFRP part inspection. A practical verification of the approach is planned later in the project.

  2. Automatic optical inspection of regular grid patterns with an inspection camera used below the Shannon-Nyquist criterion for optical resolution

    NASA Astrophysics Data System (ADS)

    Ferreira, Flávio P.; Forte, Paulo M. F.; Felgueiras, Paulo E. R.; Bret, Boris P. J.; Belsley, Michael S.; Nunes-Pereira, Eduardo J.

    2017-02-01

    An Automatic Optical Inspection (AOI) system for optical inspection of imaging devices used in automotive industry using an inspecting optics of lower spatial resolution than the device under inspection is described. This system is robust and with no moving parts. The cycle time is small. Its main advantage is that it is capable of detecting and quantifying defects in regular patterns, working below the Shannon-Nyquist criterion for optical resolution, using a single low resolution image sensor. It is easily scalable, which is an important advantage in industrial applications, since the same inspecting sensor can be reused for increasingly higher spatial resolutions of the devices to be inspected. The optical inspection is implemented with a notch multi-band Fourier filter, making the procedure especially fitted for regular patterns, like the ones that can be produced in image displays and Head Up Displays (HUDs). The regular patterns are used in production line only, for inspection purposes. For image displays, functional defects are detected at the level of a sub-image display grid element unit. Functional defects are the ones impairing the function of the display, and are preferred in AOI to the direct geometric imaging, since those are the ones directly related with the end-user experience. The shift in emphasis from geometric imaging to functional imaging is critical, since it is this that allows quantitative inspection, below Shannon-Nyquist. For HUDs, the functional detect detection addresses defects resulting from the combined effect of the image display and the image forming optics.

  3. 6th International Microbeam Workshop

    SciTech Connect

    Dr Kevin M. Prise

    2004-01-01

    The extended abstracts which are submitted here present a summary of the proceedings of the 6th International Workshop/12th LH Gray Workshop: Microbeam Probes of Cellular Radiation Response, held at St. Catherine's College, University of Oxford, UK on March, 29th-31st, 2003. In 1993 the 4th LH Gray Workshop entitled ''Microbeam Probes of Cellular Radiation Response'' was held at the Gray Cancer Institute in Northwood. This was organized by Prof BD Michael, Dr M. Folkard and Dr KM Prise and brought together 40 participants interested in developing and applying new microbeam technology to problems in radiation biology (1). The workshop was an undoubted success and has spawned a series of subsequent workshops every two years. In the past, these workshops have been highly successful in bringing together groups interested in developing and applying micro-irradiation techniques to the study of cell and tissue damage by ionizing radiations. Following the first microbeam workshop, there has been a rapid growth in the number of centres developing radiobiology microbeams, or planning to do so and there are currently 15-20 worldwide. Much of the recent research using microbeams has used them to study low-dose effects and ''non-targeted'' responses such bystander effects, genomic instability and adaptive responses. The goal of the 6th workshop was to build on our knowledge of the development of microbeam approaches and the application to radiation biology in the future with the meeting stretching over a 3 day period. Over 80 participants reviewed the current state of radiobiology microbeam research worldwide and reported on new technological developments both in the fields of physics and biology.

  4. The 6th FDR prize

    NASA Astrophysics Data System (ADS)

    Funakoshi, Mitsuaki

    2013-06-01

    From the 58 papers published in 2012 in Fluid Dynamics Research, the following paper has been selected for the sixth FDR prize: The finite-difference lattice Boltzmann method and its application in computational aero-acoustics by Michihisa Tsutahara (Professor Emeritus, Kobe University, Japan), published in volume 44 (August 2012) 045507. This is a review paper of the author's recent work on the finite-difference lattice Boltzmann method (FDLBM). In this paper, the author introduces a modified FDLBM and its application to aero-acoustics. To solve the discrete Bhatnager, Gross and Krook equation for simulating fluid flow, the FDLBM applies a stable finite-difference scheme on a curvilinear coordinate system, whereas the ordinary lattice Boltzmann method uses regular lattices. It is known that for the lattice Boltzmann methods, there is difficulty in simulating high Mach number compressible flows in principle. To alleviate this, the author proposed the modified FDLBM, expanding the flexibility of setting time increments. With this FDLBM, the author has shown that it is possible to simulate compressible flows efficiently around complex bluff bodies and with complex aero-acoustic behaviour. The author summarizes all those works, including studies only available in Japanese up to now, in this review paper. After discussing the details of the FDLBM proposed by the author, example results of simulating the Aeolian tone generated from a circular cylinder at the Mach number M = 0.7 are shown. Then, the scheme is expanded for moving bodies by combining with the Arbitrary Lagrangian Eulerian formulation. Using this moving mesh scheme, the author shows the simulation results of the very strong sound pressure generated by a high-speed train in a tunnel. For issues of sound propagation in compressible two-phase flows whose density ratio is high, the two-particle model is introduced. Also, techniques to reduce noise generation from the flow velocity and pressure at gas

  5. 6th Amino Acid Assessment Workshop

    USDA-ARS?s Scientific Manuscript database

    The focus of the 6th workshop is on lysine, arginine, and related amino acids. Functions, metabolic pathways, clinical uses, and upper tolerance intakes are emphasized in the articles that follow. Lysine is arguably the most deficient amino acid in the food supply of countries where poverty exists, ...

  6. Kids & Family Reading Report™. 6th Edition

    ERIC Educational Resources Information Center

    Scholastic Inc., 2017

    2017-01-01

    This report presents the 6th Edition of Scholastic's biannual study of children's and parents' attitudes and behaviors about reading. The latest research touches on: (1) Reading Books for Fun; (2) Reading Aloud; (3) Summer Reading; and (4) Favorite Children's Books. This research provides both reasons to celebrate as well as a strong motivation to…

  7. PREFACE: 6th Liquid Matter Conference

    NASA Astrophysics Data System (ADS)

    Dijkstra, Marjolein; van Roij, René; Vroege, Gert Jan; Lekkerkerker, Henk; Frenkel, Daan

    2005-11-01

    This special issue of Journal of Physics: Condensed Matter contains the Proceedings of the 6th Liquid Matter Conference held in Utrecht, The Netherlands, 2-6 July 2005. The three-yearly Liquid Matter Conference is organized by the Liquids Section of the Condensed Matter Division of the European Physical Society. This series of meetings began in Lyon in 1990. The most recent meeting was held in 2003 in Konstanz. The aim of the Liquid Matter Conferences is to bring together scientists working on the liquid state of matter. This rapidly growing field includes the physics, chemistry, biology and chemical engineering of liquid matter as well as various applied research areas. In fact, the Utrecht meeting had, for the first time, a special session devoted to Fundamental Challenges in Applied Liquid Physics and Microfluidics. The Utrecht meeting had 760 registered participants from four continents. An important event at this meeting was the award of the First Liquid Matter Prize of the European Physical Society to Professor Jean-Pierre Hansen FRS, of Cambridge University. In addition to a plenary speech by the recipient of the Liquid Matter Prize, the scientific programme consisted of 10 plenary lectures, 117 symposia talks, 25 of which were keynote lectures and some 650 poster contributions. The meeting also hosted a one-day symposium of the Division of Liquids and Interfaces of the Chemical Sciences division of NWO. This special issue of Journal of Physics: Condensed Matter contains 61 of the oral communications. Liquid state physics is at the interface of many fields of research. As a consequence, many of the attendants come from adjacent fields and find in the Liquid Matter Conference a forum to meet experts from other areas of research. This aspect of the Liquid Matter Conference makes it an exciting meeting as it not only offers the participants an up-to-date picture of the status of research into the liquid state of matter, but it also allows them to establish new

  8. 6th International Immunoglobulin Symposium: poster presentations.

    PubMed

    Fernandez-Cruz, E; Kaveri, S V; Peter, H-H; Durandy, A; Cantoni, N; Quinti, I; Sorensen, R; Bussel, J B; Danieli, M G; Winkelmann, A; Bayry, J; Käsermann, F; Späth, P; Helbert, M; Salama, A; van Schaik, I N; Yuki, N

    2009-12-01

    The posters presented at the 6th International Immunoglobulin Symposium covered a wide range of fields and included both basic science and clinical research. From the abstracts accepted for poster presentation, 12 abstracts were selected for oral presentations in three parallel sessions on immunodeficiencies, autoimmunity and basic research. The immunodeficiency presentations dealt with novel, rare class-switch recombination (CSR) deficiencies, attenuation of adverse events following IVIg treatment, association of immunoglobulin (Ig)G trough levels and protection against acute infection in patients with X-linked agammaglobulinaemia (XLA) and common variable immunodeficiency (CVID), and the reduction of class-switched memory B cells in patients with specific antibody deficiency (SAD). The impact of intravenous immunoglobulin on fetal alloimmune thrombocytopenia, pregnancy and postpartum-related relapses in multiple sclerosis and refractory myositis, as well as experiences with subcutaneous immunoglobulin in patients with multi-focal motor neuropathy, were the topics presented in the autoimmunity session. The interaction of dendritic cell (DC)-SIGN and alpha2,6-sialylated IgG Fc and its impact on human DCs, the enrichment of sialylated IgG in plasma-derived IgG, as wells as prion surveillance and monitoring of anti-measles titres in immunoglobulin products, were covered in the basic science session. In summary, the presentations illustrated the breadth of immunoglobulin therapy usage and highlighted the progress that is being made in diverse areas of basic and clinical research, extending our understanding of the mechanisms of immunoglobulin action and contributing to improved patient care.

  9. 6th International Conference on Emerging Zoonoses.

    PubMed

    Kahn, R E; Morozov, I; Feldmann, H; Richt, J A

    2012-09-01

    The 6th International Conference on Emerging Zoonoses, held at Cancun, Mexico, 24-27 February 2011, offered 84 participants from 18 countries, a snapshot of current research in numerous zoonoses caused by viruses, bacteria or prions. Co-chaired by Professors Heinz Feldmann and Jürgen Richt, the conference explored 10 topics: (i) The ecology of emerging zoonotic diseases; (ii) The role of wildlife in emerging zoonoses; (iii) Cross-species transmission of zoonotic pathogens; (iv) Emerging and neglected influenza viruses; (v) Haemorrhagic fever viruses; (vi) Emerging bacterial diseases; (vii) Outbreak responses to zoonotic diseases; (viii) Food-borne zoonotic diseases; (ix) Prion diseases; and (x) Modelling and prediction of emergence of zoonoses. Human medicine, veterinary medicine and environmental challenges are viewed as a unity, which must be considered under the umbrella of 'One Health'. Several presentations attempted to integrate the insights gained from field data with mathematical models in the search for effective control measures of specific zoonoses. The overriding objective of the research presentations was to create, improve and use the tools essential to address the risk of contagions in a globalized society. In seeking to fulfil this objective, a three-step approach has often been applied: (i) use cultured cells, model and natural animal hosts and human clinical models to study infection; (ii) combine traditional histopathological and biochemical approaches with functional genomics, proteomics and computational biology; and (iii) obtain signatures of virulence and insights into mechanisms of host defense response, immune evasion and pathogenesis. This meeting review summarizes 39 of the conference presentations and mentions briefly the 16 articles in this Special Supplement, most of which were presented at the conference in earlier versions. The full affiliations of all presenters and many colleagues have been included to facilitate further inquiries

  10. 6th International Meshing Roundtable '97

    SciTech Connect

    White, D.

    1997-09-01

    The goal of the 6th International Meshing Roundtable is to bring together researchers and developers from industry, academia, and government labs in a stimulating, open environment for the exchange of technical information related to the meshing process. In the pas~ the Roundtable has enjoyed significant participation born each of these groups from a wide variety of countries. The Roundtable will consist of technical presentations from contributed papers and abstracts, two invited speakers, and two invited panels of experts discussing topics related to the development and use of automatic mesh generation tools. In addition, this year we will feature a "Bring Your Best Mesh" competition and poster session to encourage discussion and participation from a wide variety of mesh generation tool users. The schedule and evening social events are designed to provide numerous opportunities for informal dialog. A proceedings will be published by Sandia National Laboratories and distributed at the Roundtable. In addition, papers of exceptionally high quaIity will be submitted to a special issue of the International Journal of Computational Geometry and Applications. Papers and one page abstracts were sought that present original results on the meshing process. Potential topics include but are got limited to: Unstructured triangular and tetrahedral mesh generation Unstructured quadrilateral and hexahedral mesh generation Automated blocking and structured mesh generation Mixed element meshing Surface mesh generation Geometry decomposition and clean-up techniques Geometry modification techniques related to meshing Adaptive mesh refinement and mesh quality control Mesh visualization Special purpose meshing algorithms for particular applications Theoretical or novel ideas with practical potential Technical presentations from industrial researchers.

  11. 6th Annual European Antibody Congress 2010

    PubMed Central

    2011-01-01

    The 6th European Antibody Congress (EAC), organized by Terrapinn Ltd., was held in Geneva, Switzerland, which was also the location of the 4th and 5th EAC.1,2 As was the case in 2008 and 2009, the EAC was again the largest antibody congress held in Europe, drawing nearly 250 delegates in 2010. Numerous pharmaceutical and biopharmaceutical companies active in the field of therapeutic antibody development were represented, as were start-up and academic organizations and representatives from the US Food and Drug Administration (FDA). The global trends in antibody research and development were discussed, including success stories of recent marketing authorizations of golimumab (Simponi®) and canakinumab (Ilaris®) by Johnson & Johnson and Novartis, respectively, updates on antibodies in late clinical development (obinutuzumab/GA101, farletuzumab/MORAb-003 and itolizumab/T1 h, by Glycart/Roche, Morphotek and Biocon, respectively) and success rates for this fast-expanding class of therapeutics (Tufts Center for the Study of Drug Development). Case studies covering clinical progress of girentuximab (Wilex), evaluation of panobacumab (Kenta Biotech), characterization of therapeutic antibody candidates by protein microarrays (Protagen), antibody-drug conjugates (sanofi-aventis, ImmunoGen, Seattle Genetics, Wyeth/Pfizer), radio-immunoconjugates (Bayer Schering Pharma, Université de Nantes) and new scaffolds (Ablynx, AdAlta, Domantis/GlaxoSmithKline, Fresenius, Molecular Partners, Pieris, Scil Proteins, Pfizer, University of Zurich) were presented. Major antibody structural improvements were showcased, including the latest selection engineering of the best isotypes (Abbott, Pfizer, Pierre Fabre), hinge domain (Pierre Fabre), dual antibodies (Abbott), IgG-like bispecific antibodies (Biogen Idec), antibody epitope mapping case studies (Eli Lilly), insights in FcγRII receptor (University of Cambridge), as well as novel tools for antibody fragmentation (Genovis). Improvements

  12. PREFACE: 6th EEIGM International Conference on Advanced Materials Research

    NASA Astrophysics Data System (ADS)

    Horwat, David; Ayadi, Zoubir; Jamart, Brigitte

    2012-02-01

    The 6th EEIGM Conference on Advanced Materials Research (AMR 2011) was held at the European School of Materials Engineering (EEIGM) on the 7-8 November 2011 in Nancy, France. This biennial conference organized by the EEIGM is a wonderful opportunity for all scientists involved in the EEIGM programme, in the 'Erasmus Mundus' Advanced Materials Science and Engineering Master programme (AMASE) and the 'Erasmus Mundus' Doctoral Programme in Materials Science and Engineering (DocMASE), to present their research in the various fields of Materials Science and Engineering. This conference is also open to other universities who have strong links with the EEIGM and provides a forum for the exchange of ideas, co-operation and future orientations by means of regular presentations, posters and a round-table discussion. This edition of the conference included a round-table discussion on composite materials within the Interreg IVA project '+Composite'. Following the publication of the proceedings of AMR 2009 in Volume 5 of this journal, it is with great pleasure that we present this selection of articles to the readers of IOP Conference Series: Materials Science and Engineering. Once again it represents the interdisciplinary nature of Materials Science and Engineering, covering basic and applicative research on organic and composite materials, metallic materials and ceramics, and characterization methods. The editors are indebted to all the reviewers for reviewing the papers at very short notice. Special thanks are offered to the sponsors of the conference including EEIGM-Université de Lorraine, AMASE, DocMASE, Grand Nancy, Ville de Nancy, Region Lorraine, Fédération Jacques Villermaux, Conseil Général de Meurthe et Moselle, Casden and '+Composite'. Zoubir Ayadi, David Horwat and Brigitte Jamart

  13. Student Solutions Manual to accompany Physics, 6th Edition

    NASA Astrophysics Data System (ADS)

    Cutnell, John D.; Johnson, Kenneth W.

    2003-07-01

    Work more effectively and check solutions as you go along with the text! Written by the authors, this indispensable Student Solutions Manual provides complete worked-out solutions to 25% of the end-of-chapter problems in Cutnell & Johnson's Physics, 6th Edition. These problems are specifically indicated in the text. For the 6th Edition of their best-selling Physics, the authors have added both print and online material to encourage readers to engage in the material more interactively. Physics research clearly shows that active learning is much more effective than passive learning. The 6th edition helps readers understand the interrelationships among basic physics concepts and how they fit together to describe our physical world. Throughout the text, the authors emphasize the relevance of physics to our everyday lives.

  14. The 6th International Earth Science Olympiad: A Student Perspective

    ERIC Educational Resources Information Center

    Barlett, Luke; Cathro, Darcy; Mellow, Maddi; Tate, Clara

    2014-01-01

    In October 2012, two students from the Australian Science and Mathematics School and two from Yankalilla Area School were selected to travel to Olavarria, Argentina in order to compete in the 6th International Earth Science Olympiad (IESO). It was an opportunity for individuals with a passion for Earth science to come together from 17 countries to…

  15. Environmental Problem Perception of 6th Grade Students

    ERIC Educational Resources Information Center

    Genc, Murat; Genc, Tulin; Ergenc, Mustafa; Erkuz, Neslihan

    2016-01-01

    This study aims to examine and compare the 6th grade students' perception of environmental issues through different techniques. For this purpose, we have tried to establish the students' perception of environmental issues by studying the pictures they drew and the written texts they wrote. In this study, where we have conducted with 62 students in…

  16. The 6th International Earth Science Olympiad: A Student Perspective

    ERIC Educational Resources Information Center

    Barlett, Luke; Cathro, Darcy; Mellow, Maddi; Tate, Clara

    2014-01-01

    In October 2012, two students from the Australian Science and Mathematics School and two from Yankalilla Area School were selected to travel to Olavarria, Argentina in order to compete in the 6th International Earth Science Olympiad (IESO). It was an opportunity for individuals with a passion for Earth science to come together from 17 countries to…

  17. Working Together for Student Achievement. 6th Biennial Joint Report

    ERIC Educational Resources Information Center

    Washington State Board of Education, 2016

    2016-01-01

    The Washington State Board of Education (SBE) and the Professional Educator Standards Board (PESB) submitted this 6th biennial joint report to the Governor, Legislative Education Committees, and Superintendent of Public Instruction. The report outlines the collaborative work of the Boards, highlights accomplishments, and provides goals and…

  18. PREFACE: The 6th Nordic Meeting on Nuclear Physics

    NASA Astrophysics Data System (ADS)

    Løvhøiden, G.; Thorsteinsen, T. F.; Vaagen, J. S.

    1990-01-01

    After an unintended time gap of five years, the series of regular Nordic meetings on nuclear physics was continued with the 6th Nordic Meeting, August 10-15, 1989. The site was Utgarden in the outskirts of Kopervik, the administration center for the Saga island of Karmøy on the west-coast of Norway. Utgarden, a "peoples high-school'' with a kitchen, housing facility and a neighboring modern gymnasium with fine lecture halls, proved to be an inexpensive and adequate site for the meeting. From the time of the Vikings, the sound between Karmøyy and the mainland has been a vital part of the way to the north. Mobility and international orientation is still a signature of an area where today essential parts of Norway's oil- and metal industry are located. The conference program included a session on nuclear physics in industry and society, with contributed talks from a number of companies and technology/research institutions, which also sponsored the meeting. Lunch visits to Hydro's aluminium plant on Karmøy or alternatively to Statoil's gas terminal on the mainland, were included in the program. The scientific program gives a cross section of nuclear physics activities in which researchers from the Nordic countries are involved nowadays. The spectrum is rich, and the emphasis has shifted to higher energies than was the case five years ago. We appreciate the possibility to present this overview in a separate volume of Physica Scripta. The present issue covers nearly all the talks given at the meeting. The order deviates, however, somewhat from that of the conference program. The organizing committee tried to encourage in various ways the participation of young physicists; this effort was truely rewarded. The young participants put their imprint on the activities in the lecture halls and even more on the soccer arena. The meeting was sponsored by The University of Bergen, The Nordic Accelerator Committee, NORDITA, The Norwegian Research Council for Science and the

  19. Conference Report: The 6th International Symposium on Waterborne Pathogens

    EPA Pesticide Factsheets

    A review of current literature on the occurrence of waterborne pathogens in DW systems.This dataset is associated with the following publication:Rochelle, P., P. Klonicki, G. DiGiovanni, V. Hill, Y. Akagi, and E. Villegas. Conference Report: The 6th International Symposium on Waterborne Pathogens ISWP 2015. JOURNAL OF THE AMERICAN WATER WORKS ASSOCIATION. American Water Works Association, Denver, CO, USA, 107(10): 24-32, (2015).

  20. Workshop report for the AIAA 6th Aeroacoustics Conference

    NASA Astrophysics Data System (ADS)

    Tam, C. K. W.

    1981-12-01

    Summaries are given of the workshops conducted at the AIAA 6th Aeroacoustics Conference, each summary having been prepared 9y the workshop chairman. The six workshops are: jet noise, duct acoustics, turbomachinery noise, aircraft interior noise, airframe and propulsive lift noise, and propeller and helicopter noise. It is noted that the primary purpose of the workshops is to provide a forum where new ideas and concepts can be openly discussed and controversies freely debated.

  1. Benign recurrent abducens (6th) nerve palsy in two children.

    PubMed

    Knapp, Christopher M; Gottlob, Irene

    2004-03-01

    Benign recurrent abducens (6th) nerve palsy is rare. We found 23 cases in children reported in the literature; however, many of these cases followed immunization or were associated with viral illness. Here we report two cases of recurrent abducens nerve palsy with no obvious etiology. The diagnosis should be considered in any child who experiences abducens nerve palsy in the absence of any underlying pathology or precipitating factors.

  2. Low Dimensional Dynamics in the Crayfish 6th Ganglion

    NASA Astrophysics Data System (ADS)

    Pei, Xing; Moss, Frank

    1996-03-01

    Finding low dimensional dynamical behavior in biological preparations has received much attention. Neurons are, however, subject to random processes, or "noise". Thus specific dynamical behavior is evidenced by well defined signatures embedded in noisy data files(D. Pierson and F. Moss Phys. Rev. Lett. 75, 2124 (1995)). We report the results of a statistical search for unstable periodic orbits in the periodically stimulated 6th ganglion of the crayfish Procambarus clarkii. Electrophysiological recordings from the caudal photoreceptor neuron within the ganglion provide the data. We discuss the results in terms of the cyclic theory of chaos.

  3. 6th ESO/OHP Summer School in Astrophysical Observations

    NASA Astrophysics Data System (ADS)

    Véron, M.-P.; Meylan, G.

    1998-09-01

    The 6th ESO/OHP Summer School was hosted again at the Observatoire de Haute-Provence (OHP) from 15 to 25 July 1998. The school, held only every second years, selects 18 of Europe's most promising young doctoral students in astronomy. Courses of lectures, observations, and analysis form the intellectual menu which is aimed at teaching the process of extracting astrophysically digestible results from the photons harvested at the telescopes, such as the ESO VLT, whose four telescopes will become available to the community in turn during the next few years.

  4. 6th Japan Bioanalysis Forum Symposium: challenge of regulated bioanalysis.

    PubMed

    Igarashi, Harue

    2015-01-01

    Biomarker measurement and LC-MS analysis of large molecule pharmaceuticals (LM-MS) are becoming increasingly important in pharmaceutical development, although they are not included in the existing bioanalytical method validation guidelines in Japan. The 6th Japan Bioanalysis Forum symposium presented challenges regarding biomarkers and LM-MS, as well as the current circumstances for regulated bioanalysis, by inviting speakers from Japan, the USA, European Union and Asia-pacific. Japan Bioanalysis Forum discussion groups also presented their outcomes and openly discussed these with the attendees - over 200 dedicated individuals from industry, regulatory agencies and academia. The symposium successfully reinforced the idea that fit-for-purpose approaches are necessary, and that science should drive any judgments and actions throughout drug development.

  5. 6th National Occupational Injury Research Symposium: Advancing Occupational Injury Research Through Integration and Partnership.

    PubMed

    Castillo, Dawn N; Schuler, Christine R; Menéndez, Cammie Chaumont

    2017-02-01

    The National Occupational Injury Research Symposium (NOIRS) is the only regularly held forum exclusively dedicated to occupational injury research and prevention. The 2015 conference theme, advancing occupational injury research through integration and partnership, shaped the conference and is reflected in articles selected for this special issue. The 6th NOIRS, held May 19-21, 2015, brought together more than 250 researchers, occupational safety practitioners and students to share and discuss occupational injury research. Articles in this special issue highlight some of the research presented at the conference, reflect multiple scientific disciplines and approaches, cover a breadth of occupational injury causes and worker populations, and provide examples of research advanced by partnerships. The next NOIRS, tentatively scheduled for 2018, will build upon the theme of integration and partnership as well as feedback from conference attendees. Published by Elsevier Ltd.

  6. 6th Global College of Neuroprotection and Neuroregeneration, annual meeting.

    PubMed

    Sharma, Hari Shanker; Sharma, Aruna

    2009-07-01

    The 6th Global College of Neuroprotection and Neuroregeneration (GCNN) and 5th Society for Study on Neuroplasticity and Neuroregeneration (SSNN) conference was held jointly in the Hilton Hotel, Vienna, Austria, 1-4 March 2009. This was the second annual joint conference of the two societies and it was highly successful from a scientific point of view, as it saw a gathering of the top basic and clinical scientists whose research is currently at the cutting edge of neuroscience. This conference saw 86 invited lectures from carefully selected leading scientists from around the world, along with 56 posters of young scientists researching of a focal theme. Over the 3 days, in 32 sessions, new developments in neuroprotection and new ways to enhance neuroregeneration were discussed intensively among more than 600 delegates. In addition, approximately 40 representatives of drug companies, five representatives from scientific publishers and 14 representatives from scientific instruments and supplies-related industries also actively participated in this huge neuroscience event. The GCNN and SSNN conference achieved a new milestone in scientific success in Vienna and established an excellent new working collaboration among the participants in a pleasant, enriched environment with several social gatherings.

  7. Fundamentals of Physics, 6th Edition Enhanced Problems Version

    NASA Astrophysics Data System (ADS)

    Halliday, David; Resnick, Robert; Walker, Jearl

    2002-04-01

    No other text on the market today can match the success of Halliday, Resnick and Walker's Fundamentals of Physics. This text continues to outperform the competition year after year, and the new edition will be no exception. Intended for Calculus-based Physics courses, the 6th edition of this extraordinary text is a major redesign of the best-selling 5th edition, which still maintains many of the elements that led to its enormous success. Jearl Walker adds his unique style to this edition with the addition of new problems designed to capture, and keep, students' attention. Nearly all changes are based on suggestions from instructors and students using the 5th edition, from reviewer comments, and from research done on the process of learning. The primary goal of this text is to provide students with a solid understanding of fundamental physics concepts, and to help them apply this conceptual understanding to quantitative problem solving. The principal goal of Halliday-Resnick-Walker is to provide instructors with a tool by which they can teach students how to effectively read scientific material and successfully reason through scientific questions. To sharpen this tool, the Enhanced Problems Version of the sixth edition of Fundamentals of Physics contains over 1000 new, high-quality problems that require thought and reasoning rather than simplistic plugging of data into formulas.

  8. Proceedings of the 6th European VLBI Network Symposium

    NASA Astrophysics Data System (ADS)

    Ros, Eduardo; Porcas, Richard W.; Lobanov, Andrei P.; Zensus, J. Anton

    This volume contains the papers presented at the 6th Symposium of the European VLBI Network, held in Bonn on 25-28 June 2002. The initial aim of these biennial gatherings of European VLBI practitioners was to review in a timely manner new results and technical developments related to Very Long Baseline Interferometry. Now, however, interest and participation in the EVN Symposia reaches far beyond Europe, reflecting the fact that scientific research and development programs are carried out to a high degree in international and often truly global collaborations. More than 120 scientists from around the world registered for participation in the Symposium. The Symposium was hosted by the Max-Planck-Institut für Radioastronomie and was held at the Gustav Stresemann Institut. In addition to the scientific sessions and poster presentations, the program included an EVN Users Meeting, an MPIfR versus Rest-of-the-World football match (highly appropriate given the competing World Cup event!), a visit to the MPIfR's 100m radio telescope in Effelsberg, and a Conference Dinner held in the nearby old walled town of Bad Müunstereifel. To maximize the usefulness of these proceedings (and possibly as a daring precedent) the Editors decided to demand the written versions of talks and posters and to complete the editorial work before the meeting, and to deliver the book to the participants at the beginning of the Symposium. We thank the authors for their cooperation in delivering publication-ready electronic manuscripts and for meeting the strict deadlines. It is highly gratifying that only a handful of the 100 presentations are not represented in this volume. The editors have made minor changes to some of the contributions in order to improve readability, and take responsibility for any errors arising from these changes. Besides the authors, many individuals have contributed to the preparation of the meeting and its proceedings. In addition to many members of the MPIfR staff, we

  9. The role and modulation of CCR6+ Th17 cell populations in rheumatoid arthritis.

    PubMed

    Paulissen, Sandra M J; van Hamburg, Jan Piet; Dankers, Wendy; Lubberts, Erik

    2015-07-01

    The IL-17A producing T-helper-17 (Th17) cell population plays a major role in rheumatoid arthritis (RA) pathogenesis and has gained wide interest as treatment target. IL-17A expressing Th cells are characterized by the expression of the chemokine receptor CCR6 and the transcription factor RORC. In RA, CCR6+ Th cells were identified in peripheral blood, synovial fluid and inflamed synovial tissue. CCR6+ Th cells might drive the progression of an early inflammation towards a persistent arthritis. The CCR6+ Th cell population is heterogeneous and several subpopulations can be distinguished, including Th17, Th22, Th17.1 (also called non-classic Th1 cells), and unclassified or intermediate populations. Interestingly, some of these populations produce low levels of IL-17A but are still very pathogenic. Furthermore, the CCR6+ Th cells phenotype is unstable and plasticity exists between CCR6+ Th cells and T-regulatory (Treg) cells and within the CCR6+ Th cell subpopulations. In this review, characteristics of the different CCR6+ Th cell populations, their plasticity, and their potential impact on rheumatoid arthritis are discussed. Moreover, current approaches to target CCR6+ Th cells and future directions of research to find specific CCR6+ Th cell targets in the treatment of patients with RA and other CCR6+ Th cell mediated autoimmune diseases are highlighted.

  10. Significant changes in the 6th edition of FACT-JACIE standards affecting apheresis facilities.

    PubMed

    Schwartz, Joseph

    2017-02-01

    FACT-JACIE cellular therapy standards are being revised every 3years and currently in their 6th edition. Significant changes in the 6th edition of the standards that affect apheresis facilities participating in cellular therapy product collections are presented.

  11. 169. GENERAL VIEW DOWN 6TH AVE. VIEW TO SOUTHWEST DOWN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    169. GENERAL VIEW DOWN 6TH AVE. VIEW TO SOUTHWEST DOWN 6TH AVE. SHOWING FROM LEFT TO RIGHT, BUILDING 8 (HOSPITAL) WITH PART OF ONE OF ITS 1-STORY WARD WINGS, AND THE 3 ORIGINAL DORMITORY WINGS OF BUILDING 9 (BOQ). - Quonset Point Naval Air Station, Roger Williams Way, North Kingstown, Washington County, RI

  12. PREFACE: The 6th International Symposium on Measurement Techniques for Multiphase Flows

    NASA Astrophysics Data System (ADS)

    Okamoto, Koji; Murai, Yuichi

    2009-02-01

    Research on multi-phase flows is very important for industrial applications, including power stations, vehicles, engines, food processing, and so on. Also, from the environmental viewpoint, multi-phase flows need to be investigated to overcome global warming. Multi-phase flows originally have non-linear features because they are multi-phased. The interaction between the phases plays a very interesting role in the flows. The non-linear interaction causes the multi-phase flows to be very difficult to understand phenomena. The International Symposium on Measurement Techniques for Multi-phase Flows (ISMTMF) is a unique symposium. The target of the symposium is to exchange the state-of-the-art knowledge on the measurement techniques for non-linear multi-phase flows. Measurement technique is the key technology to understanding non-linear phenomena. The ISMTMF began in 1995 in Nanjing, China. The symposium has continuously been held every two or three years. The ISMTMF-2008 was held in Okinawa, Japan as the 6th symposium of ISMTMF on 15-17 December 2008. Okinawa has a long history as the Ryukyus Kingdom. China and Japan have had cultural and economic exchanges through Okinawa for more than 1000 years. Please enjoy Okinawa and experience its history to enhance our international communication. The present symposium was attended by 124 participants, the program included 107 contributions with 5 plenary lectures, 2 keynote lectures, and 100 oral regular paper presentations. The topics include, besides the ordinary measurement techniques for multiphase flows, acoustic and electric sensors, bubbles and microbubbles, computed tomography, gas-liquid interface, laser-imaging and PIV, oil/coal/drop and spray, solid and powder, spectral and multi-physics. This volume includes the presented papers at ISMTMF-2008. In addition to this volume, ten selected papers will be published in a special issue of Measurement Science and Technology. We would like to express special thanks to all

  13. Conference summary: 6th International conference on hyperons, charm, and beauty hadrons (BEACH04)

    SciTech Connect

    Butler, Joel N.; /Fermilab

    2004-12-01

    The 6th International Conference on Hyperons, Charm, and Beauty Hadrons (BEACH04) treated us to a wonderful array of new results. Here the author attempts to summarize the talks and discuss the conference highlights.

  14. 3. BUILDING 522, EAST SIDE, FROM ACROSS 6TH STREET AT ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. BUILDING 522, EAST SIDE, FROM ACROSS 6TH STREET AT ITS INTERSECTION WITH G STREET, LOOKING NORTHWEST. - Oakland Naval Supply Center, Aeronautical Materials Storehouses, Between E & G Streets, between Fourth & Sixth Streets, Oakland, Alameda County, CA

  15. PREFACE: 6th International Workshop on Pseudo-Hermitian Hamiltonians in Quantum Physics

    NASA Astrophysics Data System (ADS)

    Fring, Andreas; Jones, Hugh; Znojil, Miloslav

    2008-06-01

    Attempts to understand the quantum mechanics of non-Hermitian Hamiltonian systems can be traced back to the early days, one example being Heisenberg's endeavour to formulate a consistent model involving an indefinite metric. Over the years non-Hermitian Hamiltonians whose spectra were believed to be real have appeared from time to time in the literature, for instance in the study of strong interactions at high energies via Regge models, in condensed matter physics in the context of the XXZ-spin chain, in interacting boson models in nuclear physics, in integrable quantum field theories as Toda field theories with complex coupling constants, and also very recently in a field theoretical scenario in the quantization procedure of strings on an AdS5 x S5 background. Concrete experimental realizations of these types of systems in the form of optical lattices have been proposed in 2007. In the area of mathematical physics similar non-systematic results appeared sporadically over the years. However, intensive and more systematic investigation of these types of non- Hermitian Hamiltonians with real eigenvalue spectra only began about ten years ago, when the surprising discovery was made that a large class of one-particle systems perturbed by a simple non-Hermitian potential term possesses a real energy spectrum. Since then regular international workshops devoted to this theme have taken place. This special issue is centred around the 6th International Workshop on Pseudo-Hermitian Hamiltonians in Quantum Physics held in July 2007 at City University London. All the contributions contain significant new results or alternatively provide a survey of the state of the art of the subject or a critical assessment of the present understanding of the topic and a discussion of open problems. Original contributions from non-participants were also invited. Meanwhile many interesting results have been obtained and consensus has been reached on various central conceptual issues in the

  16. Curriculum Reform Movements and Science Textbooks: A Retrospective Examination of 6th Grade Science Textbooks

    ERIC Educational Resources Information Center

    Alpaslan, Muhammet Mustafa; Yalvac, Bugrahan; Loving, Cathleen C.

    2015-01-01

    Over 50 years, two major reform efforts in science education took place. The purpose of the present study is to explore how the educational reforms were reflected in nine 6th grade science textbooks published in 1975, in 1985 and in 1997 in terms of (a) the materials used, (b) the contexts to which the electricity concept was related, (c) the type…

  17. An Analysis of Writing Dispositions of 6th Grade Students in Terms of Different Variables

    ERIC Educational Resources Information Center

    Tabak, Gurkan; Topuzkanamis, Ersoy

    2014-01-01

    This research was conducted with an aim to analyze the writing dispositions of the 6th grade students in terms of different variables. The research was carried out based on the descriptive survey model. The participants of the research are composed of a total of 672 students as 342 male students and 330 female students from Ankara, Balikesir,…

  18. Summary of the National Technicians' Conference ASE/NSLC York--5/6th July 2012

    ERIC Educational Resources Information Center

    Bostock, Julia, Comp.

    2012-01-01

    This article presents a summary of the National Technicians' Conference ASE/NSLC York from July 5th to July 6th 2012. Approximately 160 technicians attended the Conference on both days. The programme included workshops and lectures and was repeated on the Friday, so that technicians who stayed for both days were able to take part in a variety of…

  19. International Conference on Vocational Guidance (6th, Hyogo, Japan, November 2-4, 1988). Final Report.

    ERIC Educational Resources Information Center

    Ashiya Univ., Hyogo (Japan).

    This conference report contains the following papers: "Keynote Address" (Fukuyama); "Predictions Regarding the Nature and Significance of Vocational Guidance during the 21st Century in the United States" (Hoyt); "The Changing Workforce and Vocational Guidance" (Inaba); "The 6th International Conference on…

  20. Curriculum Reform Movements and Science Textbooks: A Retrospective Examination of 6th Grade Science Textbooks

    ERIC Educational Resources Information Center

    Alpaslan, Muhammet Mustafa; Yalvac, Bugrahan; Loving, Cathleen C.

    2015-01-01

    Over 50 years, two major reform efforts in science education took place. The purpose of the present study is to explore how the educational reforms were reflected in nine 6th grade science textbooks published in 1975, in 1985 and in 1997 in terms of (a) the materials used, (b) the contexts to which the electricity concept was related, (c) the type…

  1. The Roles of School Readiness and Poverty-Related Risk for 6th Grade Outcomes

    PubMed Central

    Pressler, Emily; Raver, C. Cybele; Friedman-Krauss, Allison H.; Roy, Amanda

    2016-01-01

    Low-income students are at increased risk for grade retention and suspension, which dampens their chances of high school graduation, college attendance, and future success. Drawing from a sample of 357 children and their families who participated in the Chicago School Readiness Project, we examine whether greater exposure to cumulative poverty-related risk from preschool through 5th grade is associated with greater risk of student retention and suspension in 6th grade. Logistic regression results indicate that exposure to higher levels of cumulative risk across the elementary school years is associated with students’ increased risk of retention in 6th grade, even after controlling for child school readiness skills and other covariates. Importantly, findings of the association between average cumulative risk exposure and student suspension are more complex; the role of poverty-related risk is reduced to non-significance once early indicators of child school readiness and other covariates are included in regression models. While, children’s early externalizing behavior prior to kindergarten places children at greater risk of suspension 7 years later, children’s higher levels of internalizing behaviors and early math skills are associated with significantly decreased risk of suspension in the 6th grade. Together, findings from the study suggest the complex ways that both early school readiness and subsequent exposure to poverty-related risk may both serve as compelling predictors of children’s likelihood of “staying on track” academically in the 6th grade. PMID:27867447

  2. Sneak Preview of Berkeley Lab's Science at the Theatre on June 6th, 2011

    ScienceCinema

    Sanii, Babak

    2016-07-12

    Babak Sanii provides a sneak preview of Berkeley Lab's next Science at the Theater Event: Big Thinking: The Power of Nanoscience. Berkeley Lab scientists reveal how nanoscience will bring us cleaner energy, faster computers, and improved medicine. Berkeley Repertory Theatre on June 6th, 2011

  3. Parental Stress with Homeschooling K-6th Grade Children in a South Florida District

    ERIC Educational Resources Information Center

    Myers, Jennifer A.

    2017-01-01

    Parental Stress With Homeschooling K-6th Grade Children in a South Florida District. Jennifer A. Myers, 2015: Applied Dissertation, Nova Southeastern University, Abraham S. Fischler College of Education. ERIC Descriptors: Homeschooling, Stress, Stress Management, Coping This applied dissertation study was designed to inform and advance knowledge…

  4. The Roles of School Readiness and Poverty-Related Risk for 6(th) Grade Outcomes.

    PubMed

    Pressler, Emily; Raver, C Cybele; Friedman-Krauss, Allison H; Roy, Amanda

    2016-01-01

    Low-income students are at increased risk for grade retention and suspension, which dampens their chances of high school graduation, college attendance, and future success. Drawing from a sample of 357 children and their families who participated in the Chicago School Readiness Project, we examine whether greater exposure to cumulative poverty-related risk from preschool through 5(th) grade is associated with greater risk of student retention and suspension in 6(th) grade. Logistic regression results indicate that exposure to higher levels of cumulative risk across the elementary school years is associated with students' increased risk of retention in 6(th) grade, even after controlling for child school readiness skills and other covariates. Importantly, findings of the association between average cumulative risk exposure and student suspension are more complex; the role of poverty-related risk is reduced to non-significance once early indicators of child school readiness and other covariates are included in regression models. While, children's early externalizing behavior prior to kindergarten places children at greater risk of suspension 7 years later, children's higher levels of internalizing behaviors and early math skills are associated with significantly decreased risk of suspension in the 6(th) grade. Together, findings from the study suggest the complex ways that both early school readiness and subsequent exposure to poverty-related risk may both serve as compelling predictors of children's likelihood of "staying on track" academically in the 6(th) grade.

  5. Sneak Preview of Berkeley Lab's Science at the Theatre on June 6th, 2011

    SciTech Connect

    Sanii, Babak

    2011-01-01

    Babak Sanii provides a sneak preview of Berkeley Lab's next Science at the Theater Event: Big Thinking: The Power of Nanoscience. Berkeley Lab scientists reveal how nanoscience will bring us cleaner energy, faster computers, and improved medicine. Berkeley Repertory Theatre on June 6th, 2011

  6. Parental Stress with Homeschooling K-6th Grade Children in a South Florida District

    ERIC Educational Resources Information Center

    Myers, Jennifer A.

    2017-01-01

    Parental Stress With Homeschooling K-6th Grade Children in a South Florida District. Jennifer A. Myers, 2015: Applied Dissertation, Nova Southeastern University, Abraham S. Fischler College of Education. ERIC Descriptors: Homeschooling, Stress, Stress Management, Coping This applied dissertation study was designed to inform and advance knowledge…

  7. Multiwavelength observations of XTE J1859+226 on 1999, November 6th

    NASA Astrophysics Data System (ADS)

    Haswell, C. A.; Chaty, S.; Norton, A. J.; Chen, W.; Hynes, R. I.

    1999-11-01

    Further simultaneous HST and RXTE observations (visit #3) of the new X-ray transient XTE J1859+226 are scheduled for November 6th 1999 19:37 - 22:22 UT. Coordinated multi-wavelength observations (simultaneous, near-simultaneous, and following the evolution over days/weeks) would be extremely helpful. If you can observe simultaneously with HST and/or RXTE, high time-resolution data (< 10 seconds) will be particularly useful.

  8. Prevalence of Elevated Blood Pressure in Hispanic versus Non-Hispanic 6th Graders

    ERIC Educational Resources Information Center

    Tarlton, Patricia A.

    2007-01-01

    Blood pressure screening was conducted on 4,311 (Hispanic n = 763 [17.7%], White n = 2,566 [59.5%], African American n = 610 [14.1%], Asian n = 136 [3.2%], Multiracial n = 231 [5.4%], and Native American n = 5 [0.1%]) 6th-grade students enrolled in Seminole County, Florida, Public Schools from August to December 2005. Prevalence of obesity was 21%…

  9. Prevalence of Elevated Blood Pressure in Hispanic versus Non-Hispanic 6th Graders

    ERIC Educational Resources Information Center

    Tarlton, Patricia A.

    2007-01-01

    Blood pressure screening was conducted on 4,311 (Hispanic n = 763 [17.7%], White n = 2,566 [59.5%], African American n = 610 [14.1%], Asian n = 136 [3.2%], Multiracial n = 231 [5.4%], and Native American n = 5 [0.1%]) 6th-grade students enrolled in Seminole County, Florida, Public Schools from August to December 2005. Prevalence of obesity was 21%…

  10. Improving Recruiting of the 6th Recruiting Brigade Through Statistical Analysis and Efficiency Measures

    DTIC Science & Technology

    2014-12-01

    Spanish Chinese Tagalog Thai Vietnamese Korean Portuguese Recruiters w/ Secondary Language TOTAL Ratio BN Regions 6F2- SAN GABRIEL VL 30 5 1 1 0 0...predominate poses a. unique challenge for the 6th REC BDE. This research explores statistically the effect that recmiters with additional language ability...have on improving recmiting. Also, it examines how significant it would be to allocate recruiters with secondary languages in areas where those

  11. Recurrent 6th nerve palsy in a child following different live attenuated vaccines: case report

    PubMed Central

    2012-01-01

    Background Recurrent benign 6th nerve palsy in the paediatric age group is uncommon, but has been described following viral and bacterial infections. It has also been temporally associated with immunization, but has not been previously described following two different live attenuated vaccines. Case presentation A case is presented of a 12 month old Caucasian boy with recurrent benign 6th nerve palsy following measles-mumps-rubella and varicella vaccines, given on separate occasions with complete recovery following each episode. No alternate underlying etiology was identified despite extensive investigations and review. Conclusions The majority of benign 6th nerve palsies do not have a sinister cause and have an excellent prognosis, with recovery expected in most cases. The exact pathophysiology is unknown, although hypotheses including autoimmune mechanisms and direct viral invasion could explain the pathophysiology behind immunization related nerve palsies. It is important to rule out other aetiologies with thorough history, physical examination and investigations. There is limited information in the literature regarding the safety of a repeat dose of a live vaccine in this setting. Future immunizations should be considered on a case-by-case basis. PMID:22545865

  12. Improving 6th Grade Climate Literacy using New Media (CLINM) and Teacher Professional Development

    NASA Astrophysics Data System (ADS)

    Smith, G.; Schmidt, C.; Metzger, E. P.; Cordero, E. C.

    2012-12-01

    The NASA-funded project, Improving 6th Grade Climate Literacy using New Media (CLINM), is designed to improve the climate literacy of California's 450,000 6th-grade students through teacher professional development that presents climate change as an engaging context for teaching earth science standards. The project fosters experience-based interaction among learners and encourages expressive creativity and idea-exchange via the web and social media. The heart of the CLINM project is the development of an online educator-friendly experience that provides content expert-reviewed, teacher-tested, standards-based educational resources, classroom activities and lessons that make meaningful connections to NASA data and images as well as new media tools (videos, web, and phone applications) based on the Green Ninja, a climate-action superhero who fights global warming by inspiring personal action (www.greenninja.info). In this session, we will discuss this approach to professional development and share a collection of teacher-tested CLINM resources. CLINM resources are grounded in earth system science; classroom activities and lessons engage students in exploration of connections between natural systems and human systems with a particular focus on how climate change relates to everyone's need for food, water, and energy. CLINM uses a team-based approach to resource development, and partners faculty in San José State University's (SJSU) colleges of Science, Education, and Humanities and the Arts with 6th-grade teachers from local school districts, a scientist from NASA Ames Research Center and climate change education projects at Stanford University, the University of Nebraska at Lincoln, and the University of Idaho. Climate scientists and other content experts identify relevant concepts and work with science educators to develop and/or refine classroom activities to elucidate those concepts; activities are piloted in pre-service science methods courses at SJSU and in

  13. Bone Lose of the Ancient Mediterranean lumbar vertebrae : Iasos, 6th century ad.

    NASA Astrophysics Data System (ADS)

    Kaya, Serdar; Solmaz, Ilker; Ilıca, A. Turan; Karaçalıoğlu, Özgür; Damla Yılmaz, Nalan; Başoğlu, Okşan; Kılıc, Selim; Izci, Yusuf

    Evaluation of bone mineral density (BMD) of the ancient peoples has received great interest by anthropologists. The aims of this study are to investigate the lumbar vertebrae of the Iasos people during the Byzantine period, in order to determine the prevalence of bone loss and to interpret dietary conditions of ancient Mediterranean populations. Lumbar vertebrae belonging to twenty eight skeletons of the 6th c AD were analyzed by radiographs and dual energy X-ray absorptiometry. The BMD values for each biologic sex and age group were compared. The correlation between the BMD and radiological features was also analyzed. The mean BMD was 0.940 g/cm2. BMD was decreased by aging in both sexes, but it was not significant. Osteopenia was found in 11 (39%) and osteoporosis in 4 (14.3%) out 28 vertebrae. The BMD was normal in 13 (46%) out of 28 vertebrae. Osteopenia was present in 7 (38%) of 18 male vertebrae and 4 (40%) of 10 female vertebrae. The spine score was high in the male group and there was a strong positive correlation between the BMD and spine score for both sexes. This study revealed that the BMD decreased by aging and that osteopenia was a problem in both sexes of the Iasos people during the 6th c AD. There was no correlation between the BMD and radiological features for age groups and biological sexes.

  14. Periodontal treatment need of the 6th-grade Jordanian pupils.

    PubMed

    Hamasha, A A; Albashaireh, Z

    2006-05-01

    The purpose of this study was to assess the periodontal treatment needs of 6th-grade Jordanian pupils aged 12 years old. Forty-eight classes teaching 6th-grade pupils were randomly selected from the six education zones in Irbid region, Jordan. The data were collected during interviews and clinical examinations using the Community Periodontal Index of Treatment Needs (CPITN) criteria. The findings revealed that 27.5% of the examined pupils had healthy periodontium, 22.9% showed gingival bleeding on probing but no calculus, and 31.4% had calculus deposits. Pockets in the 4-5 mm range were found in 17.6% and those in the>6 mm range in 0.6% of the pupils. Healthy periodontium was found in 2.9 sextants, whereas 2.7 sextants showed gingival bleeding and calculus. Periodontal pockets were demonstrated in less than 0.4 sextants. Periodontal therapy was not required for 27.5% of the pupils. The rest of the pupils (72.5%), however, needed oral hygiene improvement, and of these 50% required professional calculus removal. This study indicated that about 73% of the sample needed oral hygiene instructions and motivation, 50% needed professional scaling, and 0.6% needed periodontal therapy. The data of this study establish a baseline data, which may help in planning dental services and initiating further research.

  15. Uranium groundwater anomalies and L'Aquila earthquake, 6th April 2009 (Italy).

    PubMed

    Plastino, Wolfango; Povinec, Pavel P; De Luca, Gaetano; Doglioni, Carlo; Nisi, Stefano; Ioannucci, Luca; Balata, Marco; Laubenstein, Matthias; Bella, Francesco; Coccia, Eugenio

    2010-01-01

    Monitoring of chemical and physical groundwater parameters has been carried out worldwide in seismogenic areas with the aim to test possible correlations between their spatial and temporal variations and strain processes. Uranium (U) groundwater anomalies were observed during the preparation phases of the recent L'Aquila earthquake of 6th April 2009 in the cataclastic rocks near the overthrust fault crossing the deep underground Gran Sasso National Laboratory. The results suggest that U may be used as a potential strain indicator of geodynamic processes occurring before the seismic swarm and the main earthquake shock. Moreover, this justifies the different radon patterns before and after the main shock: the radon releases during and after the earthquake are much than more during the preparatory period because the process does not include only the microfracturing induced by stress-strain activation, but also radon increases accompanying groundwater U anomalies.

  16. Summary of the 6th asia-pacific transport working group (APTWG) meeting

    NASA Astrophysics Data System (ADS)

    Jhang, Hogun; Ghim, Y.-c.; Wang, Zheng-Xiong; Kwon, J. M.; Tamura, N.

    2017-08-01

    This report summarizes the contributions to, and discussions at, the 6th Asia-Pacific Transport Working Group (APTWG) meeting, held on 21-25 June 2016 at Korea University, Seoul, Republic of Korea. The objective of the meeting was to develop an integrated understanding of transport phenomena in magnetically confined plasmas. To accomplish this objective, four technical working groups were organized under the headings: (1) turbulence suppression and transport bifurcation, (2) effect of magnetic topology on transport and magnetohydrodynamics-turbulence interaction, (3) nonlocality and non-diffusive transport, and (4) Energetic particles and particle/impurity transport. A summary is also given of the three plenary review talks on impurity transport, the magnetohydrodynamics relaxation process in reversed field pinch, and recent experimental and modelling results on the quiescent H-mode operation.

  17. Statistical Analysis of CFD Solutions from the 6th AIAA CFD Drag Prediction Workshop

    NASA Technical Reports Server (NTRS)

    Derlaga, Joseph M.; Morrison, Joseph H.

    2017-01-01

    A graphical framework is used for statistical analysis of the results from an extensive N- version test of a collection of Reynolds-averaged Navier-Stokes computational uid dynam- ics codes. The solutions were obtained by code developers and users from North America, Europe, Asia, and South America using both common and custom grid sequencees as well as multiple turbulence models for the June 2016 6th AIAA CFD Drag Prediction Workshop sponsored by the AIAA Applied Aerodynamics Technical Committee. The aerodynamic con guration for this workshop was the Common Research Model subsonic transport wing- body previously used for both the 4th and 5th Drag Prediction Workshops. This work continues the statistical analysis begun in the earlier workshops and compares the results from the grid convergence study of the most recent workshop with previous workshops.

  18. Rapid landscape change in 6th century northern Jordan: interdisciplinary geoarchaeological perspectives

    NASA Astrophysics Data System (ADS)

    Lucke, Bernhard

    2016-04-01

    Landscapes of the ancient fertile crescent are considered affected by soil degradation as result of long-term farming since the Neolithic, and impressive ruins of antiquity led to assumptions that their abandonment must have been conntected with reduced agricultural productivity. In this context, a valley fill near the site of Abila of the Decapolis in northern Jordan was apparently deposited largely during the 6th century AD, and provides evidence for a rapid and intense landscape change during the Late Byzantine period. However, an interdisciplinary case study of land use, soil development, and sediments found that the valley fill cannot be connected with large-scale soil erosion in the vicinity of the site. On the one hand, this is indicated by the distribution of soil development and archaeological material as marker of past land use activity in the past, which suggests that the best soils were and still are used intensively. On the other hand, the sediments seem to point to the occurrence of climatic extremes such as heavy floods, the occurrence of soil creep after water saturation, but also a significant shift to aridity which may have triggered socio-economic changes of subsistence strategies from agriculture to pastoralism. The dates of sediments which are available so far indicate that the climatic change seemingly occurred rapidly within approximately 100 years during the late 6th and early 7th century AD, possibly connected with the "year without sun" or 'Mystery Veil' which the Byzantine historian Procopius described in the year 536 AD. Modern analogies of the Pinatubo eruption in 1991 let it seem possible that a volcanic event, perhaps the outbreak of the Ilopango volcano, was connected with these environmental turbulences. Such events cannot be understood by isolated studies: without a broad interdisciplinary framework, single archives are prone to misinterpretation, and our understanding of the environmental history of Abila is still very limited.

  19. An integrated exploration model for Council Run field analogs: Regional geology and seismic stratigraphy of Devonian 6th Elk sandstones

    SciTech Connect

    Kelleher, G.; Johnson, R. )

    1991-08-01

    A geologic study of the Devonian Lock Haven 6th Elk formation along the structural front of Pennsylvania and Maryland suggest that present-day structures were active at the time of deposition. These structures barred deposition to the west and helped to localize sands in a northeast-southwest fairway. The 6th Elk sandstones occur in two major depositional lobes (located in Centre and Somerset counties in Pennsylvania, and Garret County, Maryland) and were deposited on a shallow-marine shelf by turbidity currents and later modified by storm-generated currents. Deposition of 6th Elk sands may also have been influenced by cross-strike discontinuities. A seismic study of the Council Run field aids in subsurface identification of the 6th Elk. A high-amplitude seismic anomaly across the Council Run field is correlated with increasing san thickness. Two dimensional modeling suggests that the seismic response is extremely sensitive to specific acquisition and processing techniques including filter and phase variability. Additional attribute analysis integrates the seismic data with the forward models. This results in a predictive method for potentially identifying 6th Elk sandstone development from seismic data. Applying the results of the seismic modeling at Council Run field to a seismic grid across the previously defined 6th Elk depositional fairway has identified many exploratory prospects in Lycoming and Bradford counties, Pennsylvania. This area coincides with the site of a third, previously documented, Upper Devonian depositional lobe.

  20. FOREWORD: 6th International Conference on Pumps and Fans with Compressors and Wind Turbines (ICPF2013)

    NASA Astrophysics Data System (ADS)

    Wu, Yulin; Wang, Zhengwei; Yuan, Shouqi; Shi, Weidong; Liu, Shuhong; Luo, Xingqi; Wang, Fujun

    2013-12-01

    The 6th International Conference on Pumps and Fans with Compressors and Wind Turbines (ICPF 2013) was held in Beijing, China, 19-22 September 2013, which was jointly organized by Tsinghua University and Jiangsu University. The co-organizers were Zhejiang University, Zhejiang Sci-Tech University, The State Key Laboratory of Hydroscience and Engineering, The State Key Laboratory of Automotive Safety and Energy and Beijing International Science and Technology Cooperation Base for CO2 Utilization and Reduction. The sponsor of the conference was Concepts NREC. The First International Conference on Pumps and Systems (May 1992), the Second International Conference on Pumps and Fans (October 1995), the Third International Conference on Pumps and Fans (October 1998), and the Fourth International Conference on Pumps and Fans (26-29 August 2002) were all held in Beijing and were organized by the late famous Chinese professor on fluid machinery and engineering, Professor Zuyan Mei of Tsinghua University. The conference was interrupted by the death of Professor Mei in 2003. In order to commemorate Professor Mei, the organizing committee of ICPF decided to continue organizing the conference series. The Fifth Conference on Pumps and Systems (2010 ICPF) took place in Hangzhou, Zhejiang Province, China, 18-21 October 2010, and it was jointly organized by Zhejiang University and Tsinghua University. With the development of renewable energy and new energy in China and in the world, some small types of compressor and some types of pump, as well as wind turbines are developing very fast; therefore the ICPF2013 conference included compressors and wind turbines. The theme of the conference was the application of renewable energy of pumps, compressors, fans and blowers. The content of the conference was the basic study, design and experimental study of compressors, fans, blowers and pumps; the CFD application on pumps and fans, their transient behavior, unsteady flows and multi-phase flow

  1. Latina girls' identities-in-practice in 6th grade science

    NASA Astrophysics Data System (ADS)

    Tan, Edna

    Inequalities and achievement gaps in science education among students from different racial and socioeconomic backgrounds as well as between genders in the United States are due to not just access to resources, but also to the incongruence between identities of school science with identities salient to minority students. Minority girls are especially portrayed to be estranged from prototypical school science Discourse, often characterized as white, middle class, and masculine. This dissertation, based on a two-year ethnographic study in an urban middle school in New York City, describes the authoring of novel identities-in-practice of minority girls in a 6th grade science classroom. The findings indicate that minority girls draw from out-of-school identities salient to them to author novel identities-in-practice in the various figured worlds of the 6th grade science classroom. Through taking such authorial stances, minority girls exhibit agency in negotiating for wider boundaries in their school science participation and broker for hybrid spaces of school science where the school science Discourse was destabilized and challenged to be more inclusive of everyday funds of knowledge and Discourses important to the students. The findings also highlight the dialectic relationship between an individual students' learning and participation and the school science community-of-practice and the implications such a relationship has on the learning of both individual students and the collective community-of-practice. From year one findings, curricular adaptations were enacted, with teacher and student input, on lessons centering on food and nutrition. The adapted curriculum specifically solicited for nontraditional funds of knowledge and Discourse from students and were grounded strongly in relevance to students' out of school lives. The hybrid spaces collectively brokered for by the community-of-practice were transformed in three ways: physically, politically, and

  2. 1/6TH SCALE STRIP EFFLUENT FEED TANK-MIXING RESULTS USING MCU SOLVENT

    SciTech Connect

    Hansen, E

    2006-02-01

    The purpose of this task was to determine if mixing was an issue for the entrainment and dispersion of the Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU) solvent in the Defense Waste Processing Facility (DWPF) Strip Effluent Feed Tank (SEFT). The MCU strip effluent stream containing the Cs removed during salt processing will be transferred to the DWPF for immobilization in HLW glass. In lab-scale DWPF chemical process cell testing, mixing of the solvent in the dilute nitric acid solution proved problematic, and the Savannah River National Laboratory (SRNL) was requested to perform scaled SEFT mixing tests to evaluate whether the problem was symptomatic of the lab-scale set-up or of the solvent. The solvent levels tested were 228 and 235 ppm, which represented levels near the estimated DWPF solvent limit of 239 ppm in 0.001M HNO{sub 3} solution. The 239 ppm limit was calculated by Norato in X-CLC-S-00141. The general approach for the mixing investigation was to: (1) Investigate the use of fluorescent dyes to aid in observing the mixing behavior. Evaluate and compare the physical properties of the fluorescent dyed MCU solvents to the baseline Oak Ridge CSSX solvent. Based on the data, use the dyed MCU solvent that best approximates the physical properties. (2) Use approximately a 1/6th linear scale of the SEFT to replicate the internal configuration for DWPF mixing. (3) Determine agitator speed(s) for scaled testing based on the DWPF SEFT mixing speed. (4) Perform mixing tests using the 1/6th SEFT and determine any mixing issues (entrainment/dispersion, accumulation, adhesion) through visual observations and by pulling samples to assess uniformity. The mixing tests used MCU solvent fabricated at SRNL blended with Risk Reactor DFSB-K43 fluorescent dye. This dyed SRNL MCU solvent had equivalent physical properties important to mixing as compared to the Oak Ridge baseline solvent, blended easily with the MCU solvent, and provided an excellent visual aid.

  3. PREFACE: 6th International Workshop on Multi-Rate Processes and Hysteresis (MURPHYS2012)

    NASA Astrophysics Data System (ADS)

    Dimian, Mihai; Rachinskii, Dmitrii

    2015-02-01

    The International Workshop on Multi-Rate Processes and Hysteresis (MURPHYS) conference series focuses on multiple scale systems, singular perturbation problems, phase transitions and hysteresis phenomena occurring in physical, biological, chemical, economical, engineering and information systems. The 6th edition was hosted by Stefan cel Mare University in the city of Suceava located in the beautiful multicultural land of Bukovina, Romania, from May 21 to 24, 2012. This continued the series of biennial multidisciplinary conferences organized in Cork, Ireland from 2002 to 2008 and in Pécs, Hungary in 2010. The MURPHYS 2012 Workshop brought together more than 50 researchers in hysteresis and multi-scale phenomena from the United State of America, the United Kingdom, France, Germany, Italy, Ireland, Czech Republic, Hungary, Greece, Ukraine, and Romania. Participants shared and discussed new developments of analytical techniques and numerical methods along with a variety of their applications in various areas, including material sciences, electrical and electronics engineering, mechanical engineering and civil structures, biological and eco-systems, economics and finance. The Workshop was sponsored by the European Social Fund through Sectoral Operational Program Human Resources 2007-2013 (PRO-DOCT) and Stefan cel Mare University, Suceava. The Organizing Committee was co-chaired by Mihai Dimian from Stefan cel Mare University, Suceava (Romania), Amalia Ivanyi from the University of Pecs (Hungary), and Dmitrii Rachinskii from the University College Cork (Ireland). All papers published in this volume of Journal of Physics: Conference Series have been peer reviewed through processes administered by the Editors. Reviews were conducted by expert referees to the professional and scientific standards expected of a proceedings journal published by IOP Publishing. The Guest Editors wish to place on record their sincere gratitude to Miss Sarah Toms for the assistance she provided

  4. Laboratory accreditation and inspection.

    PubMed

    Rauch, Carol A; Nichols, James H

    2007-12-01

    Clinical laboratories perform diagnostic testing in a highly regulated environment in which federal, state, and private accreditation agencies monitor the quality of testing processes. These agencies vary in the focus and stringency of their requirements, and differences exist among states. Continued accreditation requires regular inspection to assure quality of test results for physicians, insurers, and, ultimately, the patients being tested. Preparation for inspection requires understanding of the unique accreditation requirements for each institution, establishment of quality assurance and quality improvement oversight, and communication of each staff member's role in delivering quality test results for patient care.

  5. In vitro Comparative Evaluation of Tensile Bond Strength of 6(th), 7(th) and 8(th) Generation Dentin Bonding Agents.

    PubMed

    Kamble, Suresh S; Kandasamy, Baburajan; Thillaigovindan, Ranjani; Goyal, Nitin Kumar; Talukdar, Pratim; Seal, Mukut

    2015-05-01

    Newer dentin bonding agents were developed to improve the quality of composite restoration and to reduce time consumption in its application. The aim of the present study was to evaluate tensile bond strength of 6(th), 7(th) and 8(th) generation bonding agents by in vitro method. Selected 60 permanent teeth were assigned into 20 in each group (Group I: 6(th) generation bonding agent-Adper SE plus 3M ESPE, Group II: 7(th) generation bonding agent-G-Bond GC Corp Japan and Group III: 8(th) generation dentin adhesives-FuturaBond, DC, Voco, Germany). With high-speed diamond disc, coronal dentin was exposed, and selected dentin bonding agents were applied, followed by composite restoration. All samples were saved in saline for 24 h and tensile bond strength testing was done using a universal testing machine. The obtained data were tabulated and statistically analyzed using ANOVA test. The tensile bond strength readings for 6(th) generation bonding agent was 32.2465, for 7(th) generation was 31.6734, and for 8(th)-generation dentine bonding agent was 34.74431. The highest tensile bond strength was seen in 8(th) generation bonding agent compared to 6(th) and 7(th) generation bonding agents. From the present study it can be conclude that 8(th) generation dentine adhesive (Futura DC, Voco, Germany) resulted in highest tensile bond strength compared to 6(th) (Adper SE plus, 3M ESPE) and 7(th) generation (G-Bond) dentin bonding agents.

  6. Genetics of multifactorial disorders: proceedings of the 6th Pan Arab Human Genetics Conference.

    PubMed

    Nair, Pratibha; Bizzari, Sami; Rajah, Nirmal; Assaf, Nada; Al-Ali, Mahmoud Taleb; Hamzeh, Abdul Rezzak

    2016-04-20

    The 6th Pan Arab Human Genetics Conference (PAHGC), "Genetics of Multifactorial Disorders" was organized by the Center for Arab Genomic Studies (http://www.cags.org.ae) in Dubai, United Arab Emirates from 21 to 23 January, 2016. The PAHGCs are held biennially to provide a common platform to bring together regional and international geneticists to share their knowledge and to discuss common issues. Over 800 delegates attended the first 2 days of the conference and these came from various medical and scientific backgrounds. They consisted of geneticists, molecular biologists, medical practitioners, postdoctoral researchers, technical staff (e.g., nurses and lab technicians) and medical students from 35 countries around the world. On the 3rd day, a one-day workshop on "Genetic Counseling" was delivered to 26 participants. The conference focused on four major topics, namely, diabetes, genetics of neurodevelopmental disorders, congenital anomalies and cancer genetics. Personalized medicine was a recurrent theme in most of the research presented at the conference, as was the application of novel molecular findings in clinical settings. This report discusses a summary of the presentations from the meeting.

  7. Prevention and Treatment of Cancer: Hypes and Hopes 6th International Translational Cancer Research Conference.

    PubMed

    Patel, Prabhudas; Vora, Hemangini; Aggarwal, Bharat B; Gandhi, Varsha; Mehta, Kapil; Pathak, Sen

    2016-09-01

    Cancer is primarily an "old-age" disease that has an "age-old" history. The overall incidence of cancer is much higher in Western countries, but is rapidly growing in Eastern countries perhaps due to change in life-style. Almost three million studies published to date indicate that cancer is a hyperproliferative disorder that arises from dysregulation of multiple cell signaling pathways. The cancer genome landscape indicates that approximately 140 genes and 12 cell signaling pathways drive almost all cancers. "Targeted therapy," a buzz word in cancer treatment for the past two decades, has provided antibodies, as well as small-molecule inhibitors. These therapies have been successful only in few instances. However, in most cases, minor increase in overall survival has been reported at the cost of huge expense. An alternative strategy is to prevent cancer or to diagnose and treat the disease at an early stage to gain survival benefits. Such interventions are also cost-effective. To address some of these issues, the 6th International Translational Cancer Research Conference was held during February 4-7th, 2016, in Ahmedabad, Gujarat, India; the homeland of Mahatma Gandhi. This conference was focused on utilizing multidisciplinary approaches for prevention and early treatment that would likely simultaneously or sequentially target many key pathways. Several distinguished speakers were invited from around the world. This article highlights primary features of this conference.

  8. Leather material found on a 6th B.C. Chinese bronze sword: A technical study

    NASA Astrophysics Data System (ADS)

    Luo, Wugan; Si, Yi; Wang, Hongmin; Qin, Ying; Huang, Fengchun; Wang, Changsui

    2011-09-01

    During July to November, 2006, an important archaeological excavation was conducted in Yun country, Hubei province, southern China. Chinese archaeologists found some remnant of leather materials, covered with red pigments, on a 6th century B.C. Chinese bronze sword. To understand the technology/ies that may have been utilized for manufacturing the leathers, a combined of Raman spectroscopy, FT-IR and XRF was thus applied to the remnant of leather materials. Raman analyses showed that red pigment on the leather was cinnabar (HgS). FT-IR and XRF analyses indicated that the content of some elements, such as Ca (existing as CaCO 3) and Fe (existing as Fe 2O 3), were much higher than those in the surrounding grave soil. The results inferred an application of lime depilation and retting, and the Fe-Al compound salt as tanning agent. And it was furthermore implicated that the Fe-Al salt tanning technique had been developed in the middle and late Spring and Autumn Period of China.

  9. Prevalence of elevated blood pressure in Hispanic versus non-Hispanic 6th graders.

    PubMed

    Tarlton, Patricia A

    2007-02-01

    Blood pressure screening was conducted on 4,311 (Hispanic n = 763 [17.7%], White n = 2,566 [59.5%], African American n = 610 [14.1%], Asian n = 136 [3.2%], Multiracial n = 231 [5.4%], and Native American n = 5 [0.1%]) 6th-grade students enrolled in Seminole County, Florida, Public Schools from August to December 2005. Prevalence of obesity was 21% for the overall population, with Hispanics n = 218 (28.6%) having a greater prevalence than non-Hispanics n = 630 (19.0%). Following a second screening, overall prevalence of elevated blood pressure was 1.9%, with Hispanics at 2.6% versus 1.6% for non-Hispanics. This was found to be significant when Hispanics were further compared to the White population. However, when adjusted for obesity, elevated blood pressure was not significant for Hispanics. Results confirm the presence of elevated blood pressure and obesity in all population groups, with an elevated risk for both among the Hispanic population.

  10. Consensus report from the 6th International forum for liver MRI using gadoxetic acid.

    PubMed

    Sirlin, Claude B; Hussain, Hero K; Jonas, Eduard; Kanematsu, Masayuki; Min Lee, Jeong; Merkle, Elmar M; Peck-Radosavljevic, Markus; Reeder, Scott B; Ricke, Jens; Sakamoto, Michiie

    2014-09-01

    As the utility of liver-specific magnetic resonance imaging (MRI) increases, it is pertinent to optimize and expand protocols to improve accuracy and foster evolution of techniques; in turn, positive impacts should be seen in patient management. This article reports on the latest expert thinking and current evidence in the field of liver-specific MRI, as discussed at the 6(th) International Forum for Liver MRI, which was held in Vancouver, Canada in September 2012. Topics discussed at this forum described the use of gadoxetic acid-enhanced MRI for the assessment of liver function at the segmental level; to increase accuracy in the diagnosis of liver metastases; to overcome current challenges in patients with cirrhosis, including management of arterial hypo-/isovascular, hepatobiliary phase hypointense nodules; and the data which would be required in order to recommend the use of this modality in hepatocellular carcinoma management guidelines. Growing evidence suggests that gadoxetic acid-enhanced MRI can help to improve the management of patients with a number of different liver disorders; however, more data are needed in some areas, and there may be a case for developing an interpretation guideline for gadoxetic acid-enhanced MRI findings to aid standardization. © 2013 Wiley Periodicals, Inc.

  11. The relationship between snack intake and its availability of 4th-6th graders in Taiwan.

    PubMed

    Hang, Chi-Ming; Lin, Wei; Yang, Hsiao-Chi; Pan, Wen-Harn

    2007-01-01

    The purpose of this study was to examine the relationship between the snack intake and snack availability of elementary school children. Data analyzed were from 722 4th to 6th graders' food availability and food intake questionnaires collected in the Nutrition and Health Survey in Taiwan Elementary School Children 2001-2002. The snacks commonly eaten were divided into two groups. Healthy snacks included dairy products, 100% fruit juice and fresh fruits. Unhealthy snacks included high fat/sugar snacks, cookies, candy, carbonated/sugared beverages and fast food. Structural equating modeling was used to test the models that describe the availability and intake of two snack groups. Results indicated that parents' intake and children's preference were major predictors of children intake of both healthy and unhealthy snacks. Other than that, the intake of unhealthy snacks was positively associated with "purchase by children themselves" but not the intake of healthy snacks, which was influenced predominantly by "present in home". The results support the perception that a positive family food environment is important for improving children's diet quality. To build a healthy family food environment, parents have to not only provide healthy snacks but also limit the unhealthy snacks in home. In addition to that, the role modeling of parents as eating healthy snacks instead of unhealthy snacks themselves may help children to develop similar behaviors.

  12. FOREWORD: 6th International Symposium on Electronic Beam Ion Sources and their Applications

    NASA Astrophysics Data System (ADS)

    Liljeby, L.

    1997-01-01

    The 6th International Symposium on Electron Beam Ion sources and their Applications was held at the Manne Siegbahn Laboratory at Stockholm University, June 20-23, 1994. A symposium in this series is held every three years. The next one will be organised by Professor Reinhard Becker at the J. W. Goethe University in Frankfurt am Main, Germany. The Stockholm symposium had a total of 65 participants from 9 countries. 43 oral presentations were given and 7 posters were exhibited. For the first time in this series the proceedings have been refereed. The symposium was given generous support by the Marcus Wallbenberg Foundation for International Co-operation in Science, a support mainly used for inviting delegates from Russia and students. The organisation of the symposium was led by Dr. Carl Johan Herrlander. His efficiency, organising skill and never ending attention to all the aspects of the symposium were of the utmost importance for carrying it through. We deeply regret that the proceedings have been very much delayed. Physica Scripta has no part in causing the delay which is solely a result of my inability to enforce deadlines. We think though that the contents still is of interest in particular as a full documentation of the conference.

  13. Leather material found on a 6th B.C. Chinese bronze sword: a technical study.

    PubMed

    Luo, Wugan; Si, Yi; Wang, Hongmin; Qin, Ying; Huang, Fengchun; Wang, Changsui

    2011-09-01

    During July to November, 2006, an important archaeological excavation was conducted in Yun country, Hubei province, southern China. Chinese archaeologists found some remnant of leather materials, covered with red pigments, on a 6th century B.C. Chinese bronze sword. To understand the technology/ies that may have been utilized for manufacturing the leathers, a combined of Raman spectroscopy, FT-IR and XRF was thus applied to the remnant of leather materials. Raman analyses showed that red pigment on the leather was cinnabar (HgS). FT-IR and XRF analyses indicated that the content of some elements, such as Ca (existing as CaCO3) and Fe (existing as Fe2O3), were much higher than those in the surrounding grave soil. The results inferred an application of lime depilation and retting, and the Fe-Al compound salt as tanning agent. And it was furthermore implicated that the Fe-Al salt tanning technique had been developed in the middle and late Spring and Autumn Period of China.

  14. Summary of the 6th Annual Bladder Cancer Think Tank: new directions in urologic research.

    PubMed

    Svatek, Robert S; Rosenberg, Jonathan E; Galsky, Matthew D; Lee, Cheryl T; Latini, David M; Bochner, Bernard H; Weizer, Alon Z; Apolo, Andrea B; Sridhar, Srikala S; Kamat, Ashish M; Hansel, Donna; Flaig, Thomas W; Smith, Norm D; Lotan, Yair

    2013-10-01

    The 6th Annual Bladder Cancer Think Tank brought together a multidisciplinary group of clinicians, researchers, and representatives from the National Cancer Institute and Industry in an effort to advance bladder cancer research efforts. This year's meeting comprised panel discussions and research involving 5 separate working groups, including the Survivorship, Clinical Trials, Standardization of Care, Data Mining, and Translational Science working groups. In this manuscript, the accomplishments and objectives of the working groups are summarized. Notable efforts include: (1) the development of a survivorship care plan for early and late-stage bladder cancer; (2) the development of consensus criteria for eligibility and endpoints for bladder cancer clinical trials; (3) an improved understanding of current practice patterns regarding the use of perioperative chemotherapy in an effort to standardize care; (4) creation of a comprehensive handbook to assist researchers with developing bladder cancer databases; and (5) identification of response to therapy of high-grade non muscle invasive disease through a collaborative exchange of expertise and resources.

  15. Proceedings of the 6th US/German Workshop on Salt Repository Research, Design, and Operation

    SciTech Connect

    Hansen, Francis D.; Walter Steininger; Wilhelm Bollingerfehr

    2016-01-11

    The 6th US/German Workshop on Salt Repository Research, Design, and Operation was held in Dresden. Germany on September 7-9, 2015. Over seventy participants helped advance the technical basis for salt disposal of radioactive waste. The number of collaborative efforts continues to grow and to produce useful documentation, as well as to define the state of the art for research areas. These Proceedings are divided into Chapters, and a list of authors is included in the Acknowledgement Section. Also in this document are the Technical Agenda, List of Participants, Biographical Information, Abstracts, and Presentations. Proceedings of all workshops and other pertinent information are posted on websites hosted by Sandia National Laboratories and the Nuclear Energy Agency Salt Club. The US/German workshops provide continuity for long-term research, summarize and publish status of mature areas, and develop appropriate research by consensus in a workshop environment. As before, major areas and findings are highlighted, which constitute topical Chapters in these Proceedings. In total, the scientific breadth is substantial and while not all subject matter is elaborated into chapter format, all presentations and abstracts are published in this document. In the following Proceedings, six selected topics are developed in detail.

  16. Synopsis of the 6th Walker's Cay Colloquium on Cancer Vaccines and Immunotherapy.

    PubMed

    Kast, W Martin; Levitsky, Hyam; Marincola, Francesco M

    2004-06-22

    The 6th annual Cancer Vaccines and Immunotherapy Colloquium at Walker's Cay was held under the auspices of the Albert B. Sabin Vaccine Institute on March 10-13, 2004. The Colloquium consisted of a select group of 34 scientists representing academia, biotechnology and pharmaceutical industry. The main goal of this gathering was to promote in a peaceful and comfortable environment exchanges between basic and clinical science. The secondary benefit was to inspire novel bench to bedside ventures and at the same time provide feed back about promising and/or disappointing clinical results that could help re-frame some scientific question or guide the design of future trials. Several topics were covered that included tumor antigen discovery and validation, platforms for vaccine development, tolerance, immune suppression and tumor escape mechanisms, adoptive T cell therapy and dendritic cell-based therapies, clinical trials and assessment of response. Here we report salient points raised by speakers or by the audience during animated discussion that followed each individual presentation.

  17. PREFACE: The 6th European Conference on Applied Superconductivity (EUCAS 2003)

    NASA Astrophysics Data System (ADS)

    Vaglio, Ruggero; Donaldson, Gordon

    2004-05-01

    This special issue of Superconductor Science and Technology contains papers presented at the 6th European Conference on Applied Superconductivity (EUCAS), which was held in Sorrento, Italy, 14--18 September 2003. This important biennial event followed previous successful meetings held in Gottingen, Germany; Edinburgh, Scotland; Eindhoven, the Netherlands; Sitges (Barcelona), Spain; and Copenhagen, Denmark. Following tradition, this EUCAS conference focused on the role of superconductivity in bridging various aspects of research with a variety of concrete advanced applications. EUCAS 2003 attracted about 1000 participants from all around the world with large participation from non-European countries. This conference benefited the worldwide superconductivity community tremendously as scientists operating internationally were able to share their knowledge and experience with one another. We are grateful to all those who submitted papers to the Conference Proceedings, which will be published in an Institute of Physics Conference Series, and also to those who contributed to this special issue. Unfortunately we could not consider every one of the large number of papers submitted to this issue and we express our regret to those whose work could not be included.

  18. PREFACE: 6th Workshop on Infrared Spectroscopy and Microscopy with Accelerator-Based Sources (WIRMS11)

    NASA Astrophysics Data System (ADS)

    Lupi, Stefano; Perucchi, Andrea

    2012-05-01

    This volume of Journal of Physics: Conference Series is dedicated to a subset of papers related to the work presented at the 6th edition of the international Workshop on Infrared Spectroscopy and Microscopy with Accelerator-Based Sources (WIRMS), held in Trieste, Italy, September 4-8 2011. Previous editions of the conference were held in Porquerolles (France), Lake Tahoe (USA), Rathen (Germany), Awaji (Japan), and Banff (Canada). This edition was organized and chaired by Stefano Lupi (Roma La Sapienza) and co-chaired by Andrea Perucchi (Elettra), with the support of the Italian Synchrotron Light Laboratory ELETTRA, which was honored to host the WIRMS workshop in its tenth anniversary. The 6th WIRMS edition addressed several different topics, ranging from biochemistry to strongly correlated materials, from geology to conservation science, and from forensics to the study of cometary dusts. Representatives from the infrared scientific programs at synchrotron light sources and free-electron-laser facilities. This edition was attended by 88 participants, including representatives from the infrared scientific programs at synchrotron light sources and free-electron-laser facilities, who enjoyed the stimulating scientific presentations, several detailed discussions, and the beautiful weather and scenery of the Trieste gulf. Participants came from 16 different nations and four continents, including many young scientists, six of which were supported by the organizers. There were 45 scientific talks divided in 11 sessions: Facilities, Microspectroscopy (I, II, III), Time-Resolved Spectroscopies, Extreme Conditions, Condensed Matter, Near-Field, Imaging, THz Techniques and High-Resolution Spectroscopy. 37 posters were also presented at two very lively evening poster sessions. We would like to use the opportunity of writing this preface to thank all the participants of the workshop for the very high level of their scientific contribution and for the very friendly atmosphere

  19. [Myocardial perfusion scintigraphy 2012 in Germany. Results of the 6th Query].

    PubMed

    Lindner, O; Burchert, W; Schäfers, M; Schaefer, W

    2014-01-01

    The working group Cardiovascular Nuclear Medicine of the German Society of Nuclear Medicine presents the results of the 6th survey on myocardial perfusion scintigraphy (MPS) of the reporting year 2012. 278 questionnaires (177 private practices (PP), 78 hospitals (HO), 23 university hospitals (UH)) were evaluated. MPS of 105,941 patients were reported. 95% [2005 = 80%] of MPS studies were conducted with (99m)Tc perfusion radiopharmaceuticals and only 5% with 201Tl. 79% [2009 = 76%] of the MPS were performed in PP, 15% [2009 = 17%] in HO, and 6% [2009 = 7%] in UH. Data from 108 centres which participated in all surveys from 2005 to 2012 showed an increase in MPS numbers of 4.0% (PP +6.1%, HO +18.2%, UH -18.3%). 29% of all participants (27% of PP, 31% of HO, and 26% of UH) noticed no change and 26% of all participants (28% of PP, 17% of HO and 35% of UH) an increase in their MPS requests since the 2009 query. The type of stress was pharmacological in 39% [2009 = 31%]. Of these 61% with adenosine (39% with exercise), 22% with regadenoson (51% with exercise), 14% with dipyridamole (60% with exercise), and 3% with dobutamine. Gated SPECT was performed in 73% [2009 = 56%] of all rest, in 70% [2009 = 56%] of all stress and in 67% [47%] of all stress and rest MPS. Only 36% [2009 = 33%] of the centres performed a quantification of all their studies with scores, whereas 41% [2009 = 52%] did not apply any quantification. 60% [2009 = 49%] of the MPS were requested by ambulatory care cardiologists. The survey on MPS in Germany reveals a good conformity of imaging procedures with the current guideline. A positive development in MPS practice and referral can be stated. However, there is still some potential of MPS processing considering the quantitative perfusion analysis.

  20. 32 CFR 1662.5 - Inspection, copying, and obtaining copies.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... SYSTEM FREEDOM OF INFORMATION ACT (FOIA) PROCEDURES § 1662.5 Inspection, copying, and obtaining copies... may make an appointment to inspect or copy the materials requested during regular business hours by...

  1. Meeting on Optical Engineering, 6th, Tel Aviv, Israel, Dec. 19-21, 1988, Proceedings

    SciTech Connect

    Finkler, R.; Shamir, J.

    1989-01-01

    Optical engineering papers are presented, covering topics such as IR detectors, noncontact measurement and inspection, physical optics applications, interferometric testing, design and recording of holographic optic elements, IR targets and backgrounds, optical design for the IR, and applications of interferometry and holography. Other topics include positioning systems, optical fibers, optical system design and fabrication, image processing and visual perception, thin films, and waveguides. Additional subjects include astronomical imaging, electrooptical devices, atmospheric turbulence, IR radiometry, lasers and intracavity design, random atmospheric phenomena, solar concentrators, simulation of atmospheric properties, and the design of optical systems for solar applications.

  2. New archeointensity data from French Early Medieval pottery production (6th-10th century AD). Tracing 1500 years of geomagnetic field intensity variations in Western Europe

    NASA Astrophysics Data System (ADS)

    Genevey, Agnès; Gallet, Yves; Jesset, Sébastien; Thébault, Erwan; Bouillon, Jérôme; Lefèvre, Annie; Le Goff, Maxime

    2016-08-01

    Nineteen new archeointensity results were obtained from the analysis of groups of French pottery fragments dated to the Early Middle Ages (6th to 10th centuries AD). They are from several medieval ceramic production sites, excavated mainly in Saran (Central France), and their precise dating was established based on typo-chronological characteristics. Intensity measurements were performed using the Triaxe protocol, which takes into account the effects on the intensity determinations of both thermoremanent magnetization anisotropy and cooling rate. Intensity analyses were also carried out on modern pottery produced at Saran during an experimental firing. The results show very good agreement with the geomagnetic field intensity directly measured inside and around the kiln, thus reasserting the reliability of the Triaxe protocol and the relevance of the quality criteria used. They further demonstrate the potential of the Saran pottery production for archeomagnetism. The new archeointensity results allow a precise and coherent description of the geomagnetic field intensity variations in Western Europe during the Early Medieval period, which was until now poorly documented. They show a significant increase in intensity during the 6th century AD, high intensity values from the 7th to the 9th century, with a minimum of small amplitude at the transition between the 7th and the 8th centuries and finally an important decrease until the beginning of the 11th century. Together with published intensity results available within a radius of 700 km around Paris, the new data were used to compute a master curve of the Western European geomagnetic intensity variations over the past 1500 years. This curve clearly exhibits five intensity maxima: at the transition between the 6th and 7th century AD, at the middle of the 9th century, during the 12th century, in the second part of the 14th century and at the very beginning of the 17th century AD. Some of these peaks are smoothed, or

  3. Environmental Attitudes of the 6th Grade Students from Rural and Urban Areas: A Case Study for Ankara

    ERIC Educational Resources Information Center

    Tuncer, Gaye; Sungur, Semra; Tekkaya, Ceren; Ertepinar, Hamide

    2004-01-01

    This study investigated environmental attitude of 6th grade students living in rural and urban areas in Ankara. Hundred and thirty-eight students were selected from four schools located in these areas. A 45-item questionnaire consisting of four dimensions was used to measure students' environmental attitude. Results of the study revealed that,…

  4. Story Telling: Research and Action to Improve 6th Grade Students' Views about Certain Aspects of Nature of Science

    ERIC Educational Resources Information Center

    Kahraman, Feray; Karatas, Faik Özgür

    2015-01-01

    This study is a four-week section of ongoing attempts that aim to improve 6th grade students' understandings of the nature of science. The study was carried out in a sixth grade science and technology class at a rural middle school with 15 students on the basis of action research methodology. During the study, four different stories based on the…

  5. Examining Students' Views on the Nature of Science: Results from Korean 6th, 8th, and 10th Graders

    ERIC Educational Resources Information Center

    Kang, Sukjin; Scharmann, Lawrence C.; Noh, Taehee

    2005-01-01

    In this study, students' views on the nature of science (NOS) were investigated with the use of a large-scale survey. An empirically derived multiple-choice format questionnaire was administered to 1702 Korean 6th, 8th, and 10th graders. The questionnaire consisted of five items that respectively examined students' views on five constructs…

  6. A Critical Analysis of Academic & Recreational Reading Motivation and Its Correlation to Reading FCAT Performance for 6th Grade Students

    ERIC Educational Resources Information Center

    DiBella, Karen S.

    2014-01-01

    The purpose of this study was to measure the motivation for academic and recreational reading of 6th grade students in a middle school located in southwest Florida using the Elementary Reading Attitude Survey (ERAS). In this mixed methods study, motivation for both types of reading were measured, individual demographics of the population, such as…

  7. The Effects of a Traditional and Technology-Based After-School Program on 6th Grade Student's Mathematics Skills

    ERIC Educational Resources Information Center

    Hu, Xiangen; Craig, Scotty D.; Bargagliotti, Anna E.; Graesser, Arthur C.; Okwumabua, Theresa; Anderson, Celia; Cheney, Kyle R.; Sterbinsky, Allan

    2012-01-01

    This study investigated the effectiveness of the Assessment and LEarning in Knowledge Spaces (ALEKS) system as a method of strategic intervention in after-school settings to improve the mathematical skills of struggling 6th grade students. Students were randomly assigned to after-school classrooms in which they either worked with ALEKS to improve…

  8. Assessment of 6th Grade Elementary School Students, Their Parents' and Branch Teachers' Perspective on Physical Education Classes

    ERIC Educational Resources Information Center

    Boyraz, Sirin; Ozbar, Nurper; Yetgin, Meral Kucuk; Koksalan, Burke

    2015-01-01

    A total of 437 volunteers including 54 teachers, 218 6th grade students and 102 parents from Beykoz Elementary Schools participated in this study to understand the perspectives of students, families and teachers on Physical Education classes. The perspectives of students, families and teachers of other branches are identified by survey method.…

  9. Story Telling: Research and Action to Improve 6th Grade Students' Views about Certain Aspects of Nature of Science

    ERIC Educational Resources Information Center

    Kahraman, Feray; Karatas, Faik Özgür

    2015-01-01

    This study is a four-week section of ongoing attempts that aim to improve 6th grade students' understandings of the nature of science. The study was carried out in a sixth grade science and technology class at a rural middle school with 15 students on the basis of action research methodology. During the study, four different stories based on the…

  10. A Critical Analysis of Academic & Recreational Reading Motivation and Its Correlation to Reading FCAT Performance for 6th Grade Students

    ERIC Educational Resources Information Center

    DiBella, Karen S.

    2014-01-01

    The purpose of this study was to measure the motivation for academic and recreational reading of 6th grade students in a middle school located in southwest Florida using the Elementary Reading Attitude Survey (ERAS). In this mixed methods study, motivation for both types of reading were measured, individual demographics of the population, such as…

  11. Primary School English Teachers' Perceptions of the English Language Curriculum of 6th, 7th and 8th Grades

    ERIC Educational Resources Information Center

    Ersen Yanik, Asli

    2008-01-01

    This study aims to investigate how the teachers who have different background characteristics perceive the goals and content of the English language curriculum implemented at the 6th, 7th and 8th grades of public primary schools. The study was conducted during the 2004-2005 school year with 368 English teachers selected from the seven regions of…

  12. Gender Representations in the Illustrations of the 6th Grade Language Textbook Used in Greek Elementary School

    ERIC Educational Resources Information Center

    Karintzaidis, Nikolaos; Christodoulou, Anastasia; Kyridis, Argyris; Vamvakidou, Ifigeneia

    2016-01-01

    This study explores the way in which the two sexes are presented in education and particularly in the illustration of the language textbook used in the 6th Grade of Greek elementary school. In a society where gender equality is constitutionally enshrined and displayed as an educational policy objective, it attempts to examine if school textbook…

  13. From Cooks to Carpenters: Measuring - A Saleable Work Skill. Occupation Simulation Packet. Grades 5th-6th.

    ERIC Educational Resources Information Center

    Kennedy, Helena

    This teacher's guide contains simulated work experiences for 5th and 6th grade students using the isolated skill concept - measuring. Teacher instructions include objectives, evaluation, and sequence of activities. The guide contains pre-tests and post-tests with instructions and answer keys. Three pre-skill activities are suggested, such as…

  14. An Early Warning System: Predicting 10th Grade FCAT Success from 6th Grade FCAT Performance. Research Brief. Volume 0711

    ERIC Educational Resources Information Center

    Froman, Terry; Brown, Shelly; Lapadula, Maria

    2008-01-01

    This Research Brief presents a method for predicting 10th grade Florida Comprehensive Assessment Test (FCAT) success from 6th grade FCAT performance. A simple equation provides the most probable single score prediction, and give-or-take error margins define high and low probability zones for expected 10th grade scores. In addition, a double-entry…

  15. Assessment of 6th Grade Elementary School Students, Their Parents' and Branch Teachers' Perspective on Physical Education Classes

    ERIC Educational Resources Information Center

    Boyraz, Sirin; Ozbar, Nurper; Yetgin, Meral Kucuk; Koksalan, Burke

    2015-01-01

    A total of 437 volunteers including 54 teachers, 218 6th grade students and 102 parents from Beykoz Elementary Schools participated in this study to understand the perspectives of students, families and teachers on Physical Education classes. The perspectives of students, families and teachers of other branches are identified by survey method.…

  16. 6th Annual European Antibody Congress 2010: November 29-December 1, 2010, Geneva, Switzerland.

    PubMed

    Beck, Alain; Wurch, Thierry; Reichert, Janice M

    2011-01-01

    The 6th European Antibody Congress (EAC), organized by Terrapinn Ltd., was held in Geneva, Switzerland, which was also the location of the 4th and 5th EAC. As was the case in 2008 and 2009, the EAC was again the largest antibody congress held in Europe, drawing nearly 250 delegates in 2010. Numerous pharmaceutical and biopharmaceutical companies active in the field of therapeutic antibody development were represented, as were start-up and academic organizations and representatives from the US Food and Drug Administration FDA. The global trends in antibody research and development were discussed, including success stories of recent marketing authorizations of golimumab (Simponi®) and canakinumab (Ilaris®) by Johnson & Johnson and Novartis, respectively, updates on antibodies in late clinical development (obinutuzumab/GA101, farletuzumab/MORAb-003 and itolizumab/T1 h, by Glycart/Roche, Morphotek and Biocon, respectively) and success rates for this fast-expanding class of therapeutics (Tufts Center for the Study of Drug Development). Case studies covering clinical progress of girentuximab (Wilex), evaluation of panobacumab (Kenta Biotech), characterization of therapeutic antibody candidates by protein microarrays (Protagen), antibody-drug conjugates (sanofi-aventis, ImmunoGen, Seattle Genetics, Wyeth/Pfizer), radio-immunoconjugates (Bayer Schering Pharma, Université de Nantes) and new scaffolds (Ablynx, AdAlta, Domantis/GlaxoSmithKline, Fresenius, Molecular Partners, Pieris, Scil Proteins, Pfizer, University of Zurich) were presented. Major antibody structural improvements were showcased, including the latest selection engineering of the best isotypes (Abbott, Pfizer, Pierre Fabre), hinge domain (Pierre Fabre), dual antibodies (Abbott), IgG-like bispecific antibodies (Biogen Idec), antibody epitope mapping case studies (Eli Lilly), insights in FcγRII receptor (University of Cambridge), as well as novel tools for antibody fragmentation (Genovis). Improvements of

  17. Storm Peak Laboratory 5th-6th Grade Climate and Weather Program

    NASA Astrophysics Data System (ADS)

    McCubbin, I. B.; Hallar, A. G.

    2008-12-01

    science. At the end of the day each student has a data sheet with measurements recorded from 5 locations of different elevations to take back to the classroom. Following the field trip, SPL scientists and educators visit the school for a follow-up to help children grasp concepts, represent their data set collected in graphical formats, answer questions, and evaluate students" learning. Currently, approximately 250 students annually participate in the SPL 5th and 6th grade climate education program.

  18. Proceedings from the 6th Annual University of Calgary Leaders in Medicine Research Symposium.

    PubMed

    Roberts, Jodie I; Beatty, Jennifer K; Peplowski, Michael A; Keough, Michael B; Yipp, Bryan G; Hollenberg, Morley D; Beck, Paul L

    2015-12-04

    On November 14, 2014, the Leaders in Medicine (LIM) program at the Cumming School of Medicine, University of Calgary hosted its 6th Annual Research Symposium. Dr. Danuta Skowronski, Epidemiology Lead for Influenza and Emerging Respiratory Pathogens at the British Columbia Centre for Disease Control (BCCDC), was the keynote speaker and presented a lecture entitled "Rapid response research during emerging public health crises: influenza and reflections from the five year anniversary of the 2009 pandemic". The LIM symposium provides a forum for both LIM and non-LIM medical students to present their research work, either as an oral or poster presentation. There were a total of six oral presentations and 77 posters presented. 
The oral presentations included: Swathi Damaraju, "The role of cell communication and 3D Cell-Matrix environment in a stem cell-based tissue engineering strategy for bone repair"; Menglin Yang, "The proteolytic activity of Nepenthes pitcher fluid as a therapeutic for the treatment of celiac disease"; Amelia Kellar, "Monitoring pediatric inflammatory bowel disease - a retrospective analysis of transabdominal ultrasound"; Monica M. Faria-Crowder, "The design and application of a molecular profiling strategy to identify polymicrobial acute sepsis infections"; Waleed Rahmani, "Hair follicle dermal stem cells regenerate the dermal sheath, repopulate the dermal papilla and modulate hair type"; and, Laura Palmer, "A novel role for amyloid beta protein during hypoxia/ischemia". 
The article on the University of Calgary Leaders in Medicine Program, "A Prescription that Addresses the Decline of Basic Science Education in Medical School," in a previous issue of CIM (2014 37(5):E292) provides more details on the program. Briefly, the LIM Research Symposium has the following objectives: (1) to showcase the impressive variety of projects undertaken by students in the LIM Program as well as University of Calgary medical students; (2) to encourage medical

  19. In vitro Comparative Evaluation of Tensile Bond Strength of 6th, 7th and 8th Generation Dentin Bonding Agents

    PubMed Central

    Kamble, Suresh S; Kandasamy, Baburajan; Thillaigovindan, Ranjani; Goyal, Nitin Kumar; Talukdar, Pratim; Seal, Mukut

    2015-01-01

    Background: Newer dentin bonding agents were developed to improve the quality of composite restoration and to reduce time consumption in its application. The aim of the present study was to evaluate tensile bond strength of 6th, 7th and 8th generation bonding agents by in vitro method. Materials and Methods: Selected 60 permanent teeth were assigned into 20 in each group (Group I: 6th generation bonding agent-Adper SE plus 3M ESPE, Group II: 7th generation bonding agent-G-Bond GC Corp Japan and Group III: 8th generation dentin adhesives-FuturaBond, DC, Voco, Germany). With high-speed diamond disc, coronal dentin was exposed, and selected dentin bonding agents were applied, followed by composite restoration. All samples were saved in saline for 24 h and tensile bond strength testing was done using a universal testing machine. The obtained data were tabulated and statistically analyzed using ANOVA test. Results: The tensile bond strength readings for 6th generation bonding agent was 32.2465, for 7th generation was 31.6734, and for 8th-generation dentine bonding agent was 34.74431. The highest tensile bond strength was seen in 8th generation bonding agent compared to 6th and 7th generation bonding agents. Conclusion: From the present study it can be conclude that 8th generation dentine adhesive (Futura DC, Voco, Germany) resulted in highest tensile bond strength compared to 6th (Adper SE plus, 3M ESPE) and 7th generation (G-Bond) dentin bonding agents. PMID:26028901

  20. Why are urban Indian 6th graders using more tobacco than 8th graders? Findings from Project MYTRI

    PubMed Central

    Stigler, M H; Perry, C L; Arora, M

    2006-01-01

    Objective To investigate why urban Indian 6th graders may be using more tobacco than urban Indian 8th graders. Design Cross‐sectional survey of students conducted in the summer of 2004, as the baseline evaluation tool for a group‐randomised tobacco prevention intervention trial (Project MYTRI). Mixed‐effects regression models were used to (1) examine the relationship between 15 psychosocial risk factors and current use of any tobacco, by grade; and (2) examine differences in psychosocial risk factors, by grade. Setting Thirty‐two private (high socioeconomic status (SES)) and government (low‐mid SES) schools in two large cities in India (Delhi and Chennai). Subjects Students in the 6th and 8th grade in these schools (n  =  11642). Among these, 50.6% resided in Delhi (v Chennai), 61.4% attended a government school (v a private school), 52.9% were enrolled in 6th grade (v 8th), and 54.9% were male (v female). Main outcome measure Current (past 30 day) use of any tobacco, including chewing tobacco (for example, gutkha), bidis, or cigarettes. Result Almost all psychosocial factors were significantly related to tobacco use, for students in both grades. Some of the strongest correlates included social susceptibility to and social norms about use. Exposure to tobacco advertising was a strong correlate of tobacco use for 6th graders, but not for 8th graders. Sixth graders scored lower than 8th graders on almost all factors, indicating higher risk. Conclusions The “risk profile” of 6th graders suggests they would be vulnerable to use and to begin using tobacco, as well as to outside influences that may encourage use. PMID:16723678

  1. Aircraft engine inspection

    SciTech Connect

    Burkel, R.H. )

    1990-08-01

    The inspection of new and in-service parts such as compressor blades is integral to the operations of engine manufacturers and operators alike. Subject to cracking from high temperatures and stresses, these blades must be inspected for minute cracks and surface-connected porosity at regular periods, during their entire service life. Conventional manual fluorescent penetrant inspection (FPI) is the generally accepted method for detecting these surface flaws. However, results can vary substantially, depending on the inspector's skill, experience, and human error factors. The USAF has initiated development of an integrated blade inspection system that calls for automated X-ray and infrared blade inspection systems, which have been developed along with automated FPI. Further developments have allowed all of the processing steps to be handled automatically and has led to replication of the human inspector's process of both scanning the part and evaluating any discrepancies. Finally, success with advanced FPI systems is leading to research for a larger automated system which would be capable of detecting surface flaws in larger engine parts, such as turbofan disks, compressors, and turbines.

  2. The 6th International Conference on Computer Science and Computational Mathematics (ICCSCM 2017)

    NASA Astrophysics Data System (ADS)

    2017-09-01

    The ICCSCM 2017 (The 6th International Conference on Computer Science and Computational Mathematics) has aimed to provide a platform to discuss computer science and mathematics related issues including Algebraic Geometry, Algebraic Topology, Approximation Theory, Calculus of Variations, Category Theory; Homological Algebra, Coding Theory, Combinatorics, Control Theory, Cryptology, Geometry, Difference and Functional Equations, Discrete Mathematics, Dynamical Systems and Ergodic Theory, Field Theory and Polynomials, Fluid Mechanics and Solid Mechanics, Fourier Analysis, Functional Analysis, Functions of a Complex Variable, Fuzzy Mathematics, Game Theory, General Algebraic Systems, Graph Theory, Group Theory and Generalizations, Image Processing, Signal Processing and Tomography, Information Fusion, Integral Equations, Lattices, Algebraic Structures, Linear and Multilinear Algebra; Matrix Theory, Mathematical Biology and Other Natural Sciences, Mathematical Economics and Financial Mathematics, Mathematical Physics, Measure Theory and Integration, Neutrosophic Mathematics, Number Theory, Numerical Analysis, Operations Research, Optimization, Operator Theory, Ordinary and Partial Differential Equations, Potential Theory, Real Functions, Rings and Algebras, Statistical Mechanics, Structure Of Matter, Topological Groups, Wavelets and Wavelet Transforms, 3G/4G Network Evolutions, Ad-Hoc, Mobile, Wireless Networks and Mobile Computing, Agent Computing & Multi-Agents Systems, All topics related Image/Signal Processing, Any topics related Computer Networks, Any topics related ISO SC-27 and SC- 17 standards, Any topics related PKI(Public Key Intrastructures), Artifial Intelligences(A.I.) & Pattern/Image Recognitions, Authentication/Authorization Issues, Biometric authentication and algorithms, CDMA/GSM Communication Protocols, Combinatorics, Graph Theory, and Analysis of Algorithms, Cryptography and Foundation of Computer Security, Data Base(D.B.) Management & Information

  3. PREFACE: 6th Vacuum and Surface Sciences Conference of Asia and Australia (VASSCAA-6)

    NASA Astrophysics Data System (ADS)

    Ahsan Bhatti, Javaid; Hussain, Talib; Khan, Wakil

    2013-06-01

    The Vacuum and Surface Sciences Conference of Asia and Australia (VASSCAA) conference series has been organized to create a new forum in Asia and Australia to discuss vacuum, surface and related sciences, techniques and applications. The conference series is officially endorsed by the International Union for Vacuum Science, Technique and Application (IUVSTA). The International Steering Committee of VASSCAA is comprised of Vacuum Societies in seven countries: Australia, China, India, Iran, Japan, South Korea and Pakistan. VASSCAA-1 was organized by the Vacuum Society of Japan in 1999 in Tokyo, Japan. VASSCAA-2 was held in 2002 in Hong Kong, VASSCAA-3 in Singapore in 2005. VASSCAA-4 was held in Matsue, Japan in 2008 and VASSCAA-5 in 2010 in Beijing, China. The 6th Vacuum and Surface Sciences Conference of Asia and Australia (VASSCAA-6) was held from 9-13 October 2012 in the beautiful city of Islamabad, Pakistan. The venue of the conference was the Pak-China Friendship Centre, Islamabad. More than six hundred local delgates and around seventy delegates from different countries participated in this mega event. These delegates included scientists, researchers, engineers, professors, plant operators, designers, vendors, industrialists, businessmen and students from various research organizations, technical institutions, universities, industries and companies from Pakistan and abroad. The focal point of the event was to enhance cooperation between Pakistan and the international community in the fields of vacuum, surface science and other applied technologies. At VASSCAA-6 85 oral presentations were delivered by local and foreign speakers. These were divided into different sessions according to their fields. A poster session was organized at which over 70 researchers and students displayed their posters. The best three posters won prizes. In parallel to the main conference sessions four technical short courses were held. The participants showed keen interest in all these

  4. The Efficiency of Cluster Method in Improving the Creative Writing Skill of 6th Grade Students of Primary School

    ERIC Educational Resources Information Center

    Sahbaz, Namik Kemal; Duran, Gozde

    2011-01-01

    The aim of this research is to search the effect of the cluster method on the creative writing skill of 6th grade students. In this paper, the students of 6-A, studying at Ulas Primary School in 2010-2011 academic year, were divided into two groups as experiment and control. Taking into consideration the various variants, pre-test and last-test…

  5. The Efficiency of Cluster Method in Improving the Creative Writing Skill of 6th Grade Students of Primary School

    ERIC Educational Resources Information Center

    Sahbaz, Namik Kemal; Duran, Gozde

    2011-01-01

    The aim of this research is to search the effect of the cluster method on the creative writing skill of 6th grade students. In this paper, the students of 6-A, studying at Ulas Primary School in 2010-2011 academic year, were divided into two groups as experiment and control. Taking into consideration the various variants, pre-test and last-test…

  6. [Anniversary of FSI "The 6th Central Military Clinical Hospital of the Ministry of Defense of Russian Federation"].

    PubMed

    Budko, A A; Ovechkin, I G

    2009-08-01

    The 6th Central Military Clinical Hospital of the Ministry of Defense of Russian Federation celebrates the 20th anniversary in September of 2009. The hospital is one of the greatest and well-known in the world specialized science-practical rehabilitation centers, equipped by original and unique methods, based on modern knowledge-intensive technologies. It permits resolve the most difficult tasks of reconstructive treatment of military service men of Russian Army.

  7. Possible role of nitric oxide in the protective effect of resveratrol in 5/6th nephrectomized rats.

    PubMed

    Chander, Vikas; Chopra, Kanwaljit

    2006-06-15

    Nitric oxide (NO) plays an important role in the modulation of glomerular disease. The renal protective effect of resveratrol (RVT), a polyphenolic phytoalexin, was investigated in the 5/6th nephrectomized rats. Resveratrol (5 mg/kg, PO) was administered for 12 weeks to 5/6th nephrectomized (NX) rats together with and without nitro L-arginine methyl ester (L-NAME) (10 mg/kg, IP). We evaluated the effect of these agents on proteinuria, hypertension, renal function, glomerulosclerosis, and urinary excretion of nitric oxide metabolites. 5/6th NX resulted in elevation in systolic blood pressure (SBP), reduced the urinary excretion of NO metabolites, increased urinary protein excretion, and deranged renal function and glomerulosclerosis. Treatment of animals with resveratrol significantly attenuated the increase in SBP, preserved the normal renal function, reduced the urinary protein excretion, increased the urinary excretion of NO metabolites, and prevented the glomerulosclerosis. Co-administration of animals with L-NAME along with resveratrol prevented the protection observed with resveratrol. These findings indicate that resveratrol exerts its protective effect in 5/6 NX rats through a nitric oxide pathway.

  8. Comparison of staging between the old (6th edition) and new (7th edition) TNM classifications in advanced gastric cancer.

    PubMed

    Kikuchi, Shiro; Futawatari, Nobue; Sakuramoto, Shinichi; Katada, Natsuya; Yamashita, Keishi; Shibata, Tomotaka; Nemoto, Masayuki; Watanabe, Masahiko

    2011-06-01

    The aims of the present study were to compare staging between the old (6th edition) and new (7th edition) TNM classifications, and to evaluate the prognostic impact of extended lymph node dissection according to the new nodal staging in advanced gastric cancer. A total of 609 patients with advanced gastric cancer who had undergone curative gastric resection combined with extended lymph node dissection were enrolled in the present study. Survival curves were analyzed according to staging based on the TNM 6th and 7th editions and the Japanese Classification of Gastric Carcinoma (JCGC) 14th edition. The 5-year survival rates and the consecutive stage survival with no significant differences were: IB 88%; II 74%; IIIA 53%; IIIB 39%; and IV 18% (IIIA vs. IIIB, p=0.1307) by the TNM 6th edition; IB 94%; IIA 85%; IIB 71%; IIIA 68%; IIIB 48%; IIIC 23%; and IV 13%; (IIB vs. IIIA, p=0.7665; IIIC vs. IV, p=0.4156) by the TNM 7th and JCGC 14th editions; N0 85%; N1 70%; N2 46%; N3 18%; and M1 13%; (N3 vs. M1, p=0.8640) by the TNM 6th edition; and N0 85%; N1 80%; N2 61%; N3a 46%; N3b 18%; and M1 13%; (N0 vs. N1, p=0.2735; N2 vs. N3a, p=0.0663; N3b vs. M1, p=0.8640) by the TNM 7th and JCGC 14th editions. The new classification according to the TNM 7th and the JCGC 14th editions does not always seem to be superior to the TNM 6th edition for the prognostic stratification of stages in patients who undergo curative resection for advanced gastric cancer. An extended lymph node dissection may be effective for N0-N3a, but not for N3b and M1 stages classified according to the new TNM 7th and JCGC 14th editions.

  9. PREFACE: 6th International Conference on Inverse Problems in Engineering: Theory and Practice

    NASA Astrophysics Data System (ADS)

    Bonnet, Marc

    2008-07-01

    The 6th International Conference on Inverse Problems in Engineering: Theory and Practice (ICIPE 2008) belongs to a successful series of conferences held up to now following a three-year cycle. Previous conferences took place in Palm Coast, Florida, USA (1993), Le Croisic, France (1996), Port Ludlow, Washington, USA (1999), Angra dos Reis, Brazil (2002), and Cambridge, UK (2005). The conference has its roots on the informal seminars organized by Professor J V Beck at Michigan State University, which were initiated in 1987. The organization of this Conference, which took place in Dourdan (Paris) France, 15-19 June 2008, was made possible through a joint effort by four research departments from four different universities: LEMTA (Laboratoire de Mécanique Théorique et Appliquée, Nancy-Université) LMS (Laboratoire de Mécanique des Solides, Ecole Polytechnique, Paris) LMAC (Laboratoire de Mathématiques Appliquées, UTC Compiègne) LTN (Laboratoire de Thermocinétique, Université de Nantes) It received support from three organizations: SFT (Société Française de Thermique: French Heat Transfer Association) ACSM (Association Calcul de Structures et Simulation : Computational Structural Mechanics Association) GdR Ondes - CNRS (`Waves' Network, French National Center for Scientific Research) The objective of the conference was to provide the opportunity for interaction and cross-fertilization between designers of inverse methods and practitioners. The delegates came from very different fields, such as applied mathematics, heat transfer, solid mechanics, tomography.... Consequently the sessions were organised along mostly methodological topics in order to facilitate interaction among participants who might not meet otherwise. The present proceedings, published in the Journal of Physics: Conference Series, gathers the four plenary invited lectures and the full-length versions of 103 presentations. The latter have been reviewed by the scientific committee (see

  10. [Patterns of drinking alcohol tobacco smoking among 6th year students of the faculty of medicine in Białstok].

    PubMed

    Bielska, Dorota; Kurpas, Donata; Ołtarzewska, Alicja; Piotrowska-Depta, Maria; Gomółka, Ewa; Wojtal, Mariola; Florek, Ewa

    2014-01-01

    Alcohol and tobacco are legal, easily available addictive substances. There are no universal criteria of safe alcohol consumption but some scientific studies have allowed for determination of consumption levels helpful in evaluation of the pattern of drinking and evoking readiness to limit the amount of consumed alcohol. The aim of the work was to evaluate and compare the knowledge of 6th year students of the Faculty of Medicine of the Medical University of Biatystok in the academic years 2011/12 and 2012/13 concerning the effects of alcohol abuse, as well as to determine their drinking patterns and tobacco smoking structure. The study material was collected by means of anonymous voluntary surveys carried out before classes concerning the issues of addictions within the framework of family medicine subject block. 356 students took part in the study: 226 (63.5%) women and 130 (36.5%) men (p<0.000). 4.86% of the respondents displayed a high level of knowledge on the harmfulness of alcohol abuse; 63.43% had an average level of knowledge and 31.71% - a low one. 51,32% women and 62,3% men drank alcohol in a hazardous way. A relation was found between a low level of knowledge and the amount of alcohol consumed on a typical drinking day (rS=-0.15, p=0.03) as well as between a low level of knowledge and hazardous drinking (rS=-0.13, p=0.03). Among the respondents, 18,58% women and 14,63% men smoked cigarettes regularly. Those who are 6th year students in the academic year 2012/13 usually had started smoking within the first three years of study at the Medical University and drank greater amounts of alcohol on a typical drinking day than students surveyed in the 2011/12 year. A correlation was found between tobacco smoking and a greater frequency of getting drunk occasionally (rS=-0.18, p=0.002) among students of both years. Insufficient knowledge on the effects of alcohol abuse and smoking coexist with a higher risk of drinking alcohol.

  11. Childbirth in the Greek island of Chois in the 6th century B.C., 1780, and 1914.

    PubMed

    Argenti, P

    1944-01-01

    Terracottas from the 6th century B.C.; a description of a delivery written in 1780; and a description of a labor chair used until 1914 give an historical picture of childbirth on the Greek island of Chios. The terracottas establish the fact that women were delivered in an upright perpendicular position in classical times. The upright labor chair seems to have continued in use until 1914. Midwives have historically at deliveries. In Chios, doctors seem to have taken over from midwives only around 1914.

  12. Wood - An Innovative Component of High-tech Products? 6th Wädenswil Day of Chemistry 2014.

    PubMed

    Heinzelmann, Elsbeth

    2014-10-01

    Wood is a multifunctional renewable material that could replace oil-based and other non-renewable resources in many applications. In the Swiss National Science Foundation project NFP 66, entitled 'Wood as a resource', researchers are attempting to find ways to use wood more efficiently in the future. The 6th Wädenswil Day of Chemistry, which was organised by the Institute of Chemistry and Biological Chemistry at Zurich University of Applied Sciences in Wädenswil, gave an overview of the innovative activities currently being undertaken in this field.

  13. International Methane Hydrate Research and Development Workshop (6th) held in Bergen, Norway on May 13-15, 2008

    DTIC Science & Technology

    2009-07-22

    due to methane hydrate dissociation 0 0.2 0.4 0.6 0.8 1 1200 1100 1000 900 800 700 600 500 400 300 200 100 0 D ep th (m ete r f ro m K el ly b us...Naval Research Laboratory Washington, DC 20375-5320 NRL/MR/6110--09- 9143 6th International Methane Hydrate Research and Development Workshop July 22...Prescribed by ANSI Std. Z39.18 Public reporting burden for this collection of information is estimated to average 1 hour per response, including the time for

  14. Ofsted Inspected

    ERIC Educational Resources Information Center

    Coffield, Frank

    2009-01-01

    One of the most radical actions one can take is to describe, without exaggeration or bias, exactly what is happening. The author has been reading the "Handbook for the inspection of further education and skills from September 2009." The Office for Standards in Education, Children's Services and Skills' (Ofsted's) new handbook promises a "fresh…

  15. OSHA Inspections

    DTIC Science & Technology

    2000-01-01

    Under the Occupational Safety and Health Act of 1970 (the Act), the Occupational Safety and Health Administration (OSHA) is authorized to conduct... occupational safety and health field and who are trained in OSHA standards and in the recognition of safety and health hazards. Similarly, states with...their own occupational safety and health programs conduct inspection using qualified state compliance safety and health officers.

  16. What predicts the selection of nursing as a career choice in 5th and 6th year school students?

    PubMed

    Neilson, Gavin R; Jones, Martyn C

    2012-07-01

    Demand for nursing care, and nurses, is growing in the United Kingdom given an increasingly ageing patient population with long-term co-morbidities. An ageing nursing workforce and fewer school leavers entering nursing are key barriers to student nurse recruitment. This paper aims to identify the socio-demographic and correlates nursing as a career choice in 5th and 6th year school students. This cross-sectional descriptive study gathered self-administered questionnaires from a total cohort of 5th and 6th year school students (n=1059) in one educational authority in Scotland. A response rate of 100% was achieved, with 702 students expressing a career choice. Some 71.7% (n=503) of students providing a full data set would never consider nursing, even if they obtained poor grades. Only 28.3% (n=199) would ever consider nursing. Students cited nursing as a career choice if they were female, of average to below average academic ability/achievement, expressed a positive attitude to nursing as a degree subject which was shared by their career guidance teacher. Each additional higher reduced the likelihood of nursing as a career choice by 22%. Nursing is an unpopular career choice amongst school students. Strategies are required to improve the occupational image of nursing in secondary education. Copyright © 2011 Elsevier Ltd. All rights reserved.

  17. Effect of an intervention program on the reading comprehension processes and strategies in 5th and 6th grade students.

    PubMed

    Gayo, Elena; Deaño, Manuel; Conde, Ángeles; Ribeiro, Iolanda; Cadime, Irene; Alfonso, Sonia

    2014-01-01

    Various investigations have revealed that the promotion of cognitive and metacognitive strategies can improve reading comprehension and that when readers receive this type of instruction, they can use monitoring processes and regulation strategies adequately. The goal of this work is to analyze the effects of strategic and metacognitive instruction on reading comprehension processes and strategies, using the "Aprender a Comprender" [Learning to Understand] program. Instruction was carried out in the classroom by two teachers during six months. Ninety-four students participated, 49 from 5th grade and 45 from 6th grade. A pretest-intervention-posttest-follow-up design was used with a comparison group by grade. The analysis of variance shows an impact of the intervention and its differential maintenance in each grade. The 5th-grade intervention group scored higher than the comparison group in the reading comprehension test, both at posttest and at follow-up. The 6th-grade intervention group scored higher than the comparison group in the Planning scale, both at posttest and at follow-up. Textual strategy instruction favors reading comprehension and the progressive development of planning, which is necessary for supervision and regulation, and its effects are maintained over time.

  18. Digestive disease management in Japan: a report on the 6th diagnostic pathology summer fest in 2012.

    PubMed

    Ichikawa, Kazuhito; Fujimori, Takahiro; Moriya, Takuya; Ochiai, Atsushi; Yoshinaga, Shigetaka; Kushima, Ryouji; Nagahama, Ryuji; Ohkura, Yasuo; Tanaka, Shinji; Ajioka, Yoichi; Hirata, Ichiro; Tanaka, Masanori; Hoshihara, Yoshio; Kinoshita, Yoshikazu; Sasano, Hironobu; Iwashita, Akinori; Tomita, Shigeki; Hirota, Seiichi; Yao, Takashi; Fujii, Shigehiko; Matsuda, Takahisa; Ueno, Hideki; Ishikawa, Yuichi; Takubo, Kaiyo; Fukushima, Noriyoshi; Sugai, Tamotsu; Iwafuchi, Mitsuya; Imura, Jhoji; Manabe, Toshiaki; Fukayama, Masahisa

    2013-01-01

    The 6th Diagnostic Pathology Summer Fest, held in Tokyo on August 25-26, 2012, opened its gates for everyone in the medical profession. Basic pathology training can contribute to the improvement of algorithms for diagnosis and treatment. The 6th Summer Fest with the theme 'Pathology and Clinical Treatment of Gastrointestinal Diseases' was held at the Ito International Research Center, The University of Tokyo. On August 25, 'Treatment of Early Gastrointestinal Cancer and New Guidelines' was discussed in the first session, followed by 'Biopsy Diagnosis of Digestive Tract: Key Points of Pathological Diagnosis for Inflammation and Their Clinical Significance' in the second session. On August 26, cases were discussed in the third session, and issues on pathological diagnosis and classification of neuroendorcrine tumor in the fourth session. The summaries of speeches and discussions are introduced along with the statements of each speaker. This meeting was not a formal evidence-based consensus conference, and 20 experts gave talks on their areas of specialty. Discussion was focused on how the management strategy should be standardized on the algorithm of patient care. © 2013 S. Karger AG, Basel.

  19. Substance use and youth violence. A study among 6th to 10th grade Israeli school children.

    PubMed

    Molcho, Michal; Harel, Yossi; Dina, Lache O

    2004-01-01

    This study examined the co-morbidity of substance use and violence among a representative sample of 8,394 6th-10th grade Israeli students. A representative national self report sample of 8,394 students in 6th through 10th grade. Measures included smoking, alcohol consumption, and illicit drug use, predicting involvement in bullying, injury during a fight and weapon-carrying in the past 30 days. We found across all grades, genders and ethnicities, daily smoking, use of hard drugs, history of drunkenness and binge drinking were the best predictors of violent behavior. Involvement in such behaviors put girls in higher risk for violent behaviors compared with boys. We concluded that use of substances immensely increased the odds of involvement in violent behavior, and this association was extremely strong for Arab girls. The study suggested that although girls were less frequently involved in substance use, the girls who did were at much higher risk for involvement in youth violence.

  20. Is the onset of the 6th century 'dark age' in Maya history related to explosive volcanism?

    NASA Astrophysics Data System (ADS)

    Nooren, Kees; Hoek, Wim Z.; Van der Plicht, Hans; Sigl, Michael; Galop, Didier; Torrescano-Valle, Nuria; Islebe, Gerald; Huizinga, Annika; Winkels, Tim; Middelkoop, Hans; Van Bergen, Manfred

    2016-04-01

    Maya societies in Southern Mexico, Guatemala and Belize experienced a 'dark age' during the second half of the 6th century. This period, also known as the 'Maya Hiatus', is characterized by cultural downturn, political instability and abandonment of many sites in the Central Maya Lowlands. Many theories have been postulated to explain the occurrence of this 'dark age' in Maya history. A possible key role of a large volcanic eruption in the onset of this 'dark age' will be discussed. Volcanic deposits recovered from the sedimentary archive of lake Tuspán and the Usumacinta-Grijalva delta were studied in detail and the combination of multiple dating techniques allowed the reconstruction of the timing of a large 6th century eruption. Volcanic glass shards were fingerprinted to indicate the source volcano and high resolution pollen records were constructed to indicate the environmental impact of the eruption. Results are compared with available archaeological data and causality with the disruption of Maya civilization will be evaluated.

  1. IR and py/GC/MS examination of amber relics excavated from 6th century royal tomb in Korean Peninsula

    NASA Astrophysics Data System (ADS)

    Park, Jongseo; Yun, Eunyoung; Kang, Hyungtae; Ahn, Jooyoung; Kim, Gyuho

    2016-08-01

    Relics of amber were excavated from King Muryeong's tomb constructed in the 6th century on the Korean peninsula. To estimate the provenance, FTIR (Fourier transform infrared spectroscopy) and py/GC/MS (pyrolysis/gas chromatography/mass spectrometry) analysis were utilized. The reference Baltic amber sample was also analyzed with the same method for comparison. The relics were confirmed to be amber from the FTIR analysis where an absorption band near 1150 cm- 1, characteristic one in Baltic amber, was also observed. In py/GC/MS analysis, pyrolyzed products like butanedioic acid and dehydroabietic acid, known constituents of amber, were observed. In addition, D-fenchyl alcohol, camphor, borneol and butanedioic acid, typical constituents of Baltic amber, were observed in some samples. From this, it appears that some of relics were made from Baltic amber and that Baltic amber was transported to the Korean peninsula in the time of tomb construction.

  2. 6th Annual Midwest Conference for Undergraduate Women in Physics, January 18-20, 2013, Urbana, Illinois

    SciTech Connect

    Pitts, Kevin T.

    2016-04-28

    This document is the program for the 6th Annual Midwest Conference for Undergraduate Women in Physics, which was held at the University of Illinois at Urbana-Champaign on January 18-20, 2013. The goals of the conference were to foster a culture in which undergraduate women are encouraged and supported to pursue, and also to succeed in, higher education in physics; to provide career information to students in physics and related fields; to give women the resources, motivation, and confidence to apply to graduate school and successfully complete a Ph.D. program in Physics; to provide information and dispel misconceptions about the application process for graduate school and the diverse employment opportunities in physics and related fields, enabling women to make more informed decisions about their goals and attain them; and to connect female physics students with successful female physicists to whom they can relate and who can act as inspirational role models and mentors.

  3. Publication of Proceedings for the 6th Workshop on High Energy Density and High Power RF (RF 2003)

    SciTech Connect

    Victor L. Granatstein

    2004-08-08

    The 6th Workshop on High Energy Density and High Power RF (RF 2003) was held from June 22 to June 26 at the Coolfont Resort and Conference Center in Berkeley Springs, West Virginia. The Workshop was hosted by the Institute for Research in Electronics and Applied Physics (IREAP) of the University of Maryland, College Park and by the Naval Research Laboratory, Washington DC. As its name implies this was the sixth in a series of biennial workshops devoted to exchanging information and ideas on high power microwave sources and components. The applications addressed included particle accelerators, radar, HPM, space exploration, neutron sources and plasma heating and current driven in controlled thermonuclear fusion research. This Final Report includes a brief description of the RF 2003 Workshop and the distribution of the published proceedings.

  4. 6th COSTAM/SFRR (ASEAN/Malaysia) International Workshop on Micronutrients, Oxidative Stress, and the Environment.

    PubMed

    Nesaretnam, Kalanithi; Sies, Helmut

    2006-01-01

    The 6(th) COSTAM/SFRR (ASEAN/Malaysia) workshop, "Micronutrients, Oxidative Stress, and the Environment," was held from June 29 to July 2 at Holiday Inn Damai Beach Resort in Kuching, Sarawak. Two hundred twenty participants from 17 countries presented recent advances on natural antioxidants in the area of oxidative stress and molecular aspects of nutrition. Natural products and research are an important program in academic institutions and are experiencing unprecedented interest and growth by the scientific community and public health authorities. Progress is being driven by better understanding of the molecular mechanisms of the relation between oxidative stress and micronutrient action. The gathering of scientists from around the world was fruitful, and we hope that future work will be developed by the formal and informal interactions that took place in this beautiful tropical setting.

  5. Restaurant inspection frequency and food safety compliance.

    PubMed

    Newbold, K Bruce; McKeary, Marie; Hart, Robert; Hall, Robert

    2008-11-01

    Although food premises are regularly inspected, little information is available on the effect of inspections on compliance records, particularly with respect to the impact of the frequency of inspection on compliance. The following presents the outcome of a study designed to assess the impact of increased inspection frequency on compliance measures in Hamilton, Ontario, in the absence of any other changes to food handler/safety programs or legislation. High-risk food inspection premises were randomly assigned three, four, or five inspections per year. Results indicate that no statistical difference existed in outcome measures based on frequency of inspection. When premises were grouped based on the average time between inspections, premises with greater time between inspections scored better compliance measures relative to premises that were inspected more frequently. The study was also unique for the level of consultation and collaboration sought from the public health inspectors (PHIs) assigned to the Food Safety Program. Their knowledge and experience with respect to the critical variables associated with compliance were a complementary component to the literature review conducted by the research team.

  6. [PICS: pharmaceutical inspection cooperation scheme].

    PubMed

    Morénas, J

    2009-01-01

    The pharmaceutical inspection cooperation scheme (PICS) is a structure containing 34 participating authorities located worldwide (October 2008). It has been created in 1995 on the basis of the pharmaceutical inspection convention (PIC) settled by the European free trade association (EFTA) in1970. This scheme has different goals as to be an international recognised body in the field of good manufacturing practices (GMP), for training inspectors (by the way of an annual seminar and experts circles related notably to active pharmaceutical ingredients [API], quality risk management, computerized systems, useful for the writing of inspection's aide-memoires). PICS is also leading to high standards for GMP inspectorates (through regular crossed audits) and being a room for exchanges on technical matters between inspectors but also between inspectors and pharmaceutical industry.

  7. Photometric and Spectroscopic Footprint Corrections in the Sloan Digital Sky Survey’s 6th Data Release

    NASA Astrophysics Data System (ADS)

    Specian, Mike A.; Szalay, Alex S.

    2016-04-01

    We identify and correct numerous errors within the photometric and spectroscopic footprints (SFs) of the Sloan Digital Sky Survey’s (SDSS) 6th data release (DR6). Within the SDSS’s boundaries hundreds of millions of objects have been detected. Yet we present evidence that the boundaries themselves contain a significant number of mistakes that are being revealed for the first time within this paper. Left unaddressed, these can introduce systematic biases into galaxy clustering statistics. Using the DR6 Main Galaxy Sample (MGS) targets as tracers, we reveal inconsistencies between the photometric and SF definitions provided in the Catalog Archive Server (CAS), and the measurements of targets therein. First, we find that 19.7 deg2 of the DR6 photometric footprint are devoid of MGS targets. In volumes of radii 7 {h}-1 {Mpc}, this can cause errors in the expected number of galaxies to exceed 60%. Second, we identify seven areas that were erroneously included or excluded from the SF. Moreover, the tiling algorithm that positioned spectroscopic fibers during and between DRs caused many areas along the edge of the SF to be significantly undersampled relative to the footprint’s interior. Through our corrections, we increase the completeness 2.2% by trimming 3.6% of the area from the existing SF. The sum total of these efforts has generated the most accurate description of the SDSS DR6 footprints ever created.

  8. A randomized controlled trial on the effects of yoga on stress reactivity in 6th grade students.

    PubMed

    Hagins, Marshall; Haden, Sara C; Daly, Leslie A

    2013-01-01

    There is an increasing interest in developing school programs that improve the ability of children to cope with psychosocial stress. Yoga may be an appropriate intervention as it has demonstrated improvements in the ability of children to manage psychosocial stress. Yoga is thought to improve the control of reactivity to stress via the regulation of the autonomic nervous system. The current study examined the effects of yoga compared to a physical education class on physiological response (blood pressure (BP) and heart rate (HR)) to behavioral stressor tasks (mental arithmetic and mirror tracing tasks). Data analysis of BP and HR was performed using a 2 × 2 × 4 repeated measures ANOVA (time × group × stressor time points). 30 (17 male) 6th graders participated in the study. Yoga did not provide significant differences in stress reactivity compared to a physical education class (group × time: systolic (F(1,28) = .538, P = .470); diastolic (F(1,28) = .1.061, P = .312); HR (F(1,28) = .401, P = .532)). The lack of significant differences may be due to the yoga intervention failing to focus on stress management and/or the stressor tasks not adequately capturing attenuation of stressor response.

  9. Yersinia pestis DNA from skeletal remains from the 6(th) century AD reveals insights into Justinianic Plague.

    PubMed

    Harbeck, Michaela; Seifert, Lisa; Hänsch, Stephanie; Wagner, David M; Birdsell, Dawn; Parise, Katy L; Wiechmann, Ingrid; Grupe, Gisela; Thomas, Astrid; Keim, Paul; Zöller, Lothar; Bramanti, Barbara; Riehm, Julia M; Scholz, Holger C

    2013-01-01

    Yersinia pestis, the etiologic agent of the disease plague, has been implicated in three historical pandemics. These include the third pandemic of the 19(th) and 20(th) centuries, during which plague was spread around the world, and the second pandemic of the 14(th)-17(th) centuries, which included the infamous epidemic known as the Black Death. Previous studies have confirmed that Y. pestis caused these two more recent pandemics. However, a highly spirited debate still continues as to whether Y. pestis caused the so-called Justinianic Plague of the 6(th)-8(th) centuries AD. By analyzing ancient DNA in two independent ancient DNA laboratories, we confirmed unambiguously the presence of Y. pestis DNA in human skeletal remains from an Early Medieval cemetery. In addition, we narrowed the phylogenetic position of the responsible strain down to major branch 0 on the Y. pestis phylogeny, specifically between nodes N03 and N05. Our findings confirm that Y. pestis was responsible for the Justinianic Plague, which should end the controversy regarding the etiology of this pandemic. The first genotype of a Y. pestis strain that caused the Late Antique plague provides important information about the history of the plague bacillus and suggests that the first pandemic also originated in Asia, similar to the other two plague pandemics.

  10. Bond Strength of 5th, 6th and 7th Generation Bonding Agents to Intracanal Dentin of Primary Teeth

    PubMed Central

    Afshar, Hossein; Baradaran Nakhjavani, Yahya; Rahro Taban, Sedighe; Baniameri, Zahra; Nahvi, Azam

    2015-01-01

    Objectives: This in-vitro study sought to assess the push-out bond strength of a total etch and 2 self-etch bonding systems to intracanal dentin of primary anterior teeth (PAT). Materials and Methods: Thirty-six primary anterior teeth were randomly divided into 3 groups of 5th generation (Single Bond 2), 6th generation (Clearfil SE) and 7th generation (Single Bond Universal) bonding agents. The canal orifice was restored with composite resin and the push-out test was carried out to assess the bond strength. After applying the push-out load, specimens were evaluated under a light microscope at 40X magnification. One-way ANOVA and log-rank test on Kaplan-Meier curves were applied for the comparison of bond strength among the 3 groups. Results: The mean± standard deviation (SD) bond strength was 13.6±5.33 MPa for Single Bond 2, 13.85±5.86 MPa for Clearfil SE and 12.28±5.24 MPa for Single Bond Universal. The differences in bond strength among the 3 groups were not statistically significant (P>0.05). Conclusion: All three bonding agents are recommended for use with composite posts in PAT. However, due to high technical sensitivity of the Total Etch system, single or two-step self etch systems may be preferred for uncooperative children. PMID:26056518

  11. Ethical, legal, and social aspects of farm animal cloning in the 6th Framework Programme for Research.

    PubMed

    Claxton, John; Sachez, Elena; Matthiessen-Guyader, Line

    2004-01-01

    Cloned livestock have potential importance in the provision of improved medicine as well as in the development of livestock production. The public is, however, increasingly concerned about the social and ethical consequences of these advances in knowledge and techniques. There is unevenness throughout Europe in different Member States' attitudes to research into livestock cloning. Although there is EU legislation controlling the use of animals for research purposes, there is no legislation specifically governing cloning in livestock production. The main EU reference is the 9th Opinion of the European Group on Ethics, which states "Cloning of farm animals may prove to be of medical and agricultural as well as economic benefit. It is acceptable only when the aims and methods are ethically justified and when carried out under ethical conditions." The ethical justification includes the avoidance of suffering, the use of the 3Rs principle and a lack of better alternatives. The Commission addresses these issues in the 6th Framework Programme by promoting the integration of ethical, legal and social aspects in all proposals where they are relevant, by fostering ethical awareness and foresight in the proposals, by encouraging public dialogue, and by supporting specific actions to promote the debate. Research must respect fundamental ethical principles, including animal welfare requirements.

  12. Compact Multifunction Inspection Head

    NASA Technical Reports Server (NTRS)

    Volpe, Richard A.; Ivlev, Robert; Ohm, Timothy

    1995-01-01

    Multiple-sensor inspection head designed to be mounted at tip of robot arm for performing multiple automated and/or remotely controlled inspection functions. Inspection head houses optoelectronic sensors, electrochemical sensor, sources of illumination, and parallel-jaw gripper.

  13. Highlights from the 6th Annual University of Calgary Leaders in Medicine Research Symposium and the Keynote Address by Dr. Danuta Skowronski.

    PubMed

    Roberts, Jodie I; Beatty, Jennifer K; Peplowski, Michael A; Keough, Michael B; Yipp, Bryan G; Hollenberg, Morley D; Beck, Paul L

    2015-12-04

    The Leaders in Medicine (LIM) Program at the University of Calgary hosted its 6th Annual Research Symposium on November 14, 2014, showcasing the quality and breadth of work performed by students at the Cumming School of Medicine. Participation at this year's event was our most successful to date, with a total of six oral and 77 poster presentations during the afternoon symposium. For a detailed description of the work presented at the symposium, please see the Proceedings from the 6th Annual University of Calgary Leaders in Medicine Research Symposium published in this issue of Clinical and Investigative Medicine.

  14. Iterated fractional Tikhonov regularization

    NASA Astrophysics Data System (ADS)

    Bianchi, Davide; Buccini, Alessandro; Donatelli, Marco; Serra-Capizzano, Stefano

    2015-05-01

    Fractional Tikhonov regularization methods have been recently proposed to reduce the oversmoothing property of the Tikhonov regularization in standard form, in order to preserve the details of the approximated solution. Their regularization and convergence properties have been previously investigated showing that they are of optimal order. This paper provides saturation and converse results on their convergence rates. Using the same iterative refinement strategy of iterated Tikhonov regularization, new iterated fractional Tikhonov regularization methods are introduced. We show that these iterated methods are of optimal order and overcome the previous saturation results. Furthermore, nonstationary iterated fractional Tikhonov regularization methods are investigated, establishing their convergence rate under general conditions on the iteration parameters. Numerical results confirm the effectiveness of the proposed regularization iterations.

  15. American Council on Rural Special Education (ACRES) Conference Proceedings (6th, Tucson, Arizona, April 22-25, 1986).

    ERIC Educational Resources Information Center

    American Council on Rural Special Education.

    This proceedings contains summaries, handouts, or full papers of presentations. Sample titles and presentors include the following: "Project S.E.R.T. Special Education Training for Regular Educators of Native-Americans" (C. Foster); "Effect of Inservice Education Models on Team Problem-Solving" (K. Bunch and A. Bunch); "Handicapped Preschoolers in…

  16. Breakfast patterns among low-income, ethnically-diverse 4th-6th grade children in an urban area

    PubMed Central

    2014-01-01

    Background Increasing school breakfast participation has been advocated as a method to prevent childhood obesity. However, little is known about children’s breakfast patterns outside of school (e.g., home, corner store). Policies that increase school breakfast participation without an understanding of children’s breakfast habits outside of school may result in children consuming multiple breakfasts and may undermine efforts to prevent obesity. The aim of the current study was to describe morning food and drink consumption patterns among low-income, urban children and their associations with relative weight. Methods A cross-sectional analysis was conducted of data obtained from 651 4th-6th graders (51.7% female, 61.2% African American, 10.7 years) in 2012. Students completed surveys at school that included all foods eaten and their locations that morning. Height and weight were measured by trained research staff. Results On the day surveyed, 12.4% of youth reported not eating breakfast, 49.8% reported eating one breakfast, 25.5% reported eating two breakfasts, and 12.3% reported eating three or more breakfasts. The number of breakfasts consumed and BMI percentile showed a significant curvilinear relationship, with higher mean BMI percentiles observed among children who did not consume any breakfast and those who consumed ≥ 3 breakfasts. Sixth graders were significantly less likely to have consumed breakfast compared to younger children. A greater proportion of obese youth had no breakfast (18.0%) compared to healthy weight (10.1%) and overweight youth (10.7%, p = .01). Conclusions When promoting school breakfast, policies will need to be mindful of both over- and under-consumption to effectively address childhood obesity and food insecurity. Clinical trial registration NCT01924130 from http://clinicaltrials.gov/. PMID:24928474

  17. CfDS 2006: the 6th European Dark-Skies Symposium, Portsmouth, 2006 September 15-16

    NASA Astrophysics Data System (ADS)

    Mizon, R.

    2006-12-01

    The BAA's Campaign for Dark Skies took its turn in 2006 to stage the 6th European Dark-Skies Symposium, similar events having been held in previous years in Switzerland, Germany, France and Belgium. The event was the best attended to date, with more than 150 delegates from eleven European countries, the USA and even South Africa. Between sessions, delegates were given a tour of the night skies of the world in the South Downs Planetarium, where Dr John Mason simulated the effects of light pollution. This was followed by a visit to the Clanfield Observatory, courtesy of the Hampshire Astronomical Group, later in the evening, where the real night sky and a little real light pollution (!) were observed. The whole event was kindly sponsored by the BAA and Abacus Lighting Ltd. A principal aim of the two-day symposium was to advise planners and other decision-makers, and those who make, choose and install lighting, about the legal and moral issues surrounding light pollution. It is not, of course, the Campaign's intention to ban lighting, but to ensure that where outdoor lighting is required, it is designed and installed correctly, thereby causing little or no nuisance and reducing energy costs. These non-astronomical aspects were very much to the fore on the first day of the conference, which was opened by one of CfDS' best allies in Parliament, Lembit Opik MP. Mr Opik expressed his delight at seeing so many delegates, and confirmed his continuing support for the initiatives CfDS pursues within Parliament: for example its discussions with DEFRA on the subject of the proposed planning directive (PPS 23) on light pollution

  18. [The IASLC lung cancer staging project. Comparing the current 6(th) TNM edition with the proposed 7(th) edition].

    PubMed

    Carvalho, Lina; Cardoso, Edgar; Nunes, Henrique; Baptista, Victor; Gomes, Ana; Couceiro, Patrícia

    2009-01-01

    The future 7th edition of TNM classification for lung cancer will be published in 2009 and comprises the IASLC recommendations for TNM parameters. The general staging of lung cancer includes the new parameters: reclassification of tumours larger than 7 cm from T2 to T3; extra tumoral nodules will change their category to T3, T4 and M1 when in the same, ipsilateral or contralateral lobe, respectively; pleural effusion will be M1a. With these alterations, cases staged as IB - T2b N0 M0 will be IIA, cases staged IIB - T2a N1 M0 will be IIA and cases IIIB- T4 N0- -1 M0 will be IIIA. The 7(th) TNM edition recommendations were applied to 203 broncho -pulmonary carcinomas, concerning epidermoid carcinomas (83) and adenocarcinomas (120) registered in the archive of the Serviço de Anatomia Patológica of the Hospitais da Universidade de Coimbra - Portugal, previously submitted to surgical resection and lymph node excision. The following alterations will be kept as the application of the future 7(th) TNM edition: 20 cases in stage IB will move to stage IIA (17) and stage IIB (3); 18 cases will change from stage IIB to stage IIA (17) and 1 case to stage IIIA; 2 cases from stage IIIB will move to stage IV; 6 cases in stage IV will move to stage IIIA (5) and 1 case to stage IIIB. In this translational adaptation from 6th to 7th TNM staging, 51 out of the 203 analysed cases change their staging, corresponding to 25.1%.

  19. The preparatory phase of the April 6th 2009, Mw 6.3, L’Aquila earthquake: Seismological observations

    NASA Astrophysics Data System (ADS)

    Lucente, F. P.; de Gori, P.; Margheriti, L.; Piccinini, D.; Dibona, M.; Chiarabba, C.; Piana Agostinetti, N.

    2009-12-01

    Few decades ago, the dilatancy-diffusion hypothesis held great promise as a physical basis for developing earthquakes prediction techniques, but the potential never become reality, as the result of too few observations consistent with the theory. One of the main problems has been the lack of detailed monitoring records of small earthquakes swarms spatio-temporally close to the incoming major earthquakes. In fact, the recognition of dilatancy-related effects requires the use of very dense network of three-component seismographs, which, in turn, implies the a-priori knowledge of major earthquakes location, i.e., actually a paradox. The deterministic prediction of earthquakes remains a long time, hard task to accomplish. Nevertheless, for seismologists, the understanding of the processes that preside over the earthquakes nucleation and the mechanics of faulting represents a big step toward the ability to predict earthquakes. Here we describe a set of seismological observations done on the foreshock sequence that preceded the April 6th 2009, Mw 6.3, L’Aquila earthquake. In this occasion, the dense configuration of the seismic network in the area gave us the unique opportunity for a detailed reconstruction of the preparatory phase of the main shock. We show that measurable precursory effects, as changes of the seismic waves velocity and of the anisotropic parameters in the crust, occurred before the main shock. From our observations we infer that fluids play a key role in the fault failure process, and, most significantly, that the elastic properties of the rock volume surrounding the main shock nucleation area undergo a dramatic change about a week before the main shock occurrence.

  20. Inspection and Emotion

    ERIC Educational Resources Information Center

    Perryman, Jane

    2007-01-01

    In this paper I explore the emotional impact of inspection on the staff of a school in the two years between Ofsted inspections. Using data from one school undergoing inspection, I argue that the negative emotional impact of inspection of teachers goes beyond the oft-reported issues of stress and overwork. Teachers experience a loss of power and…

  1. The Hetu'u Global Network: Measuring the Distance to the Sun Using the June 5th/6th Transit of Venus

    ERIC Educational Resources Information Center

    Faherty, Jacqueline K.; Rodriguez, David R.; Miller, Scott T.

    2012-01-01

    In the spirit of historic astronomical endeavors, we invited school groups across the globe to collaborate in a solar distance measurement using the rare June 5/6th transit of Venus. In total, we recruited 19 school groups spread over 6 continents and 10 countries to participate in our Hetu'u Global Network. Applying the methods of French…

  2. The Hetu'u Global Network: Measuring the Distance to the Sun Using the June 5th/6th Transit of Venus

    ERIC Educational Resources Information Center

    Faherty, Jacqueline K.; Rodriguez, David R.; Miller, Scott T.

    2012-01-01

    In the spirit of historic astronomical endeavors, we invited school groups across the globe to collaborate in a solar distance measurement using the rare June 5/6th transit of Venus. In total, we recruited 19 school groups spread over 6 continents and 10 countries to participate in our Hetu'u Global Network. Applying the methods of French…

  3. The Effect of Listening Education Practices Organized by Active Learning Techniques on the Attitudes of 6th Grade Students towards Turkish Course

    ERIC Educational Resources Information Center

    Aytan, Talat

    2017-01-01

    In this study, it was aimed to determine the effect of listening education practices that organized by active learning techniques on the attitudes of 6th grade students towards Turkish course. The sample of the study conducted at a secondary school in the Black Sea region of Turkey consisted of twenty students--ten girls and ten boys. During…

  4. Trends in Substance Use among 6th-to 10th-Grade Students from 1998 to 2010: Findings from a National Probability Study

    ERIC Educational Resources Information Center

    Brooks-Russell, Ashley; Farhat, Tilda; Haynie, Denise; Simons-Morton, Bruce

    2014-01-01

    Of the handful of national studies tracking trends in adolescent substance use in the United States, only the Health Behavior in School-Aged Children (HBSC) study collects data from 6th through 10th graders. The purpose of this study was to examine trends from 1998 to 2010 (four time points) in the prevalence of tobacco, alcohol, and marijuana use…

  5. Highlights from the 6th International Society for Computational Biology Student Council Symposium at the 18th Annual International Conference on Intelligent Systems for Molecular Biology

    PubMed Central

    2010-01-01

    This meeting report gives an overview of the keynote lectures and a selection of the student oral and poster presentations at the 6th International Society for Computational Biology Student Council Symposium that was held as a precursor event to the annual international conference on Intelligent Systems for Molecular Biology (ISMB). The symposium was held in Boston, MA, USA on July 9th, 2010.

  6. Trends in Substance Use among 6th-to 10th-Grade Students from 1998 to 2010: Findings from a National Probability Study

    ERIC Educational Resources Information Center

    Brooks-Russell, Ashley; Farhat, Tilda; Haynie, Denise; Simons-Morton, Bruce

    2014-01-01

    Of the handful of national studies tracking trends in adolescent substance use in the United States, only the Health Behavior in School-Aged Children (HBSC) study collects data from 6th through 10th graders. The purpose of this study was to examine trends from 1998 to 2010 (four time points) in the prevalence of tobacco, alcohol, and marijuana use…

  7. The Effect of the Van Hiele Model Based Instruction on the Creative Thinking Levels of 6th Grade Primary School Students

    ERIC Educational Resources Information Center

    Erdogan, Tolga; Akkaya, Recai; Celebi Akkaya, Sibel

    2009-01-01

    The aim of this study is to determine the effect of the Van Hiele model based instruction process on the creative thinking levels of 6th grade primary school students. Pre test-post test matching control group quasi-experimental design was used in the study. Fifty five students enrolled in sixth grades during the 2005-2006 educational year formed…

  8. Proceedings of the Office of Special Education Programs' Annual Technical Assistance and Dissemination Meeting (6th, Washington, DC, January 16-18, 1996).

    ERIC Educational Resources Information Center

    Special Education Programs (ED/OSERS), Washington, DC.

    This document presents the proceedings for the Office of Special Education Programs' 6th Annual Technical Assistance and Dissemination Meeting held on January 16-18, 1996, in Washington, DC. Conference discussions centered around changing expectations for local and state education agencies and technical assistance and dissemination (TA&D)…

  9. Integration of physical activity and technology motion devices within a combined 5th and 6th grade science curriculum

    NASA Astrophysics Data System (ADS)

    Finn, Kevin Eugene

    Background: National recommendations to increase school-based physical activity and promote academic success advise incorporating movement into traditional classroom lessons. Classroom-based physical activities have favorable associations with indicators of cognitive functioning, academic behaviors, and academic achievement. Purpose: This study analyzed the Active Science framework, which incorporated school-based physical activity within interactive science classroom lessons. Specifically, the study measured the effects of the Active Science framework on student physical activity levels in the classroom, student learning of science inquiry skills and content knowledge, and student perceptions of physical activity and science. A secondary purpose was to evaluate the teachers' perceptions on the implementation of the framework. Subjects: Participants were 37 Hispanic girls (age=11.1 +/-0.8 yr) in mixed 5th/6th grade science classes in a private, urban middle school. Methods: Physical activity levels of the students during the Active Science framework were measured using pedometers and heart rate monitors. Pre- and post-tests were used to assess the levels of learning achieved by the students in science inquiry skills and content during the Active Science framework. Student perceptions and attitudes toward science and physical activity were measured during student focus groups and pre-post perception surveys. Lesson plan evaluations completed by the teachers and structured interviews provided data on implementation of the framework. Results: Physical activity results showed heart rate (146 +/-9 bpm); maximal heart rate (196 +/-10.6 bpm); time (35 +/-2.5 mins); steps (3050 +/-402.7); calories (99 +/-8.4 kcal); and distance (1.1 +/-0.2 miles) while performing the activity portion of the science lessons were consistent with national recommendations for accumulating school-based physical activity. Significant increases in science content and skills test scores with a 22

  10. Conference scene: Summary of the 6th Conference of the Romanian Association of Medical Laboratories with international participation.

    PubMed

    Carasevici, Eugen

    2011-10-01

    The Romanian Association of Medical Laboratories (RAML) conferences have acquired a reputation for standing out as the most prominent and efficient meetings in the national community of laboratory medicine, being a landmark of the development in this field in Romania and an active affiliation to international forums. This year, the conference setting was Piatra Neamt, in the northeast part of Romania, which produced a friendly and stimulating professional environment. As in previous years, leading experts in the fields of laboratory medicine attended the event. This year, we enjoyed the opportunity to have such distinguished guests as the members of the executive board of International Federation of Clinical Chemistry and Laboratory Medicine (IFCC); Graham Beastall, IFCC President; Päivi Hannele Laitinen, IFCC secretary; and Grazyna Sypniewska, IFCC Communication and Publication Division, and editor of the electronic journal of the IFCC. As usual, the conference program included all aspects of clinical laboratory activity, with a special focus on technology development, instrumentation and laboratory management. Fully aware of the fact that the complexity and depth of laboratory practice have undergone an impressive and rapid evolution, the specific goals of the event were to increase knowledge in the fundamentals of new molecular investigation, areas which show the tendency to become routine in our daily activity. In addition, laboratory management and the place of medical laboratories in the process of translational medicine were subjects of focus. The 6th Conference of the Romanian Association of Medical Laboratories was held from Wednesday 1st to Saturday 4th of June 2011. A total of 273 participants from all local branches of the Association attended. The scientific program included seven plenary sessions where 22 lectures and 18 short communications were delivered, and three poster sessions with 44 poster presentations. Session topics covered issues of

  11. Soma, food of the immortals according to the Bower Manuscript (Kashmir, 6th century A.D.).

    PubMed

    Leonti, Marco; Casu, Laura

    2014-08-08

    Food is medicine and vice versa. In Hindu and Ayurvedic medicine, and among human cultures of the Indian subcontinent in general, the perception of the food-medicine continuum is especially well established. The preparation of the exhilarating, gold-coloured Soma, Amrita or Ambrosia, the elixir and food of the 'immortals'-the Hindu pantheon-by the ancient Indo-Aryans, is described in the Rigveda in poetic hymns. Different theories regarding the botanical identity of Soma circulate, but no pharmacologically and historically convincing theory exists to date. We intend to contribute to the botanical, chemical and pharmacological characterisation of Soma through an analysis of two historical Amrita recipes recorded in the Bower Manuscript. The recipes are referred therein as panaceas (clarified butter) and also as a medicine to treat nervous diseases (oil), while no exhilarating properties are mentioned. Notwithstanding this, we hypothesise, that these recipes are related to the ca. 1800 years older Rigvedic Soma. We suppose that the psychoactive Soma ingredient(s) are among the components, possibly in smaller proportions, of the Amrita recipes preserved in the Bower Manuscript. The Bower Manuscript is a medical treatise recorded in the 6th century A.D. in Sanskrit on birch bark leaves, probably by Buddhist monks, and unearthed towards the end of the 19th century in Chinese Turkestan. We analysed two Amrita recipes from the Bower Manuscript, which was translated by Rudolf Hoernle into English during the early 20th century. A database search with the updated Latin binomials of the herbal ingredients was used to gather quantitative phytochemical and pharmacological information. Together, both Amrita recipes contain around 100 herbal ingredients. Psychoactive alkaloid containing species still important in Ayurvedic, Chinese and Thai medicine and mentioned in the recipe for 'Amrita-Prâsa clarified butter' and 'Amrita Oil' are: Tinospora cordifolia (Amrita, Guduchi), three

  12. Bone loss during partial weight bearing (1/6th gravity) is mitigated by resistance and aerobic exercise in mice

    NASA Astrophysics Data System (ADS)

    Boudreaux, R. D.; Metzger, C. E.; Macias, B. R.; Shirazi-Fard, Y.; Hogan, H. A.; Bloomfield, S. A.

    2014-06-01

    Astronauts on long duration missions continue to experience bone loss, as much as 1-2% each month, for up to 4.5 years after a mission. Mechanical loading of bone with exercise has been shown to increase bone formation, mass, and geometry. The aim of this study was to compare the efficacy of two exercise protocols during a period of reduced gravitational loading (1/6th body weight) in mice. Since muscle contractions via resistance exercise impart the largest physiological loads on the skeleton, we hypothesized that resistance training (via vertical tower climbing) would better protect against the deleterious musculoskeletal effects of reduced gravitational weight bearing when compared to endurance exercise (treadmill running). Young adult female BALB/cBYJ mice were randomly assigned to three groups: 1/6 g (G/6; n=6), 1/6 g with treadmill running (G/6+RUN; n=8), or 1/6 g with vertical tower climbing (G/6+CLB; n=9). Exercise was performed five times per week. Reduced weight bearing for 21 days was achieved through a novel harness suspension system. Treadmill velocity (12-20 m/min) and daily run time duration (32-51 min) increased incrementally throughout the study. Bone geometry and volumetric bone mineral density (vBMD) at proximal metaphysis and mid-diaphysis tibia were assessed by in vivo peripheral quantitative computed tomography (pQCT) on days 0 and 21 and standard dynamic histomorphometry was performed on undemineralized sections of the mid-diaphysis after tissue harvest. G/6 caused a significant decrease (P<0.001) in proximal tibia metaphysis total vBMD (-9.6%). These reductions of tibia metaphyseal vBMD in G/6 mice were mitigated in both G/6+RUN and G/6+CLB groups (P<0.05). After 21 days of G/6, we saw an absolute increase in tibia mid-diaphysis vBMD and in distal metaphysis femur vBMD in both G/6+RUN and G/6+CLB mice (P<0.05). Substantial increases in endocortical and periosteal mineralizing surface (MS/BS) at mid-diaphysis tibia in G/6+CLB demonstrate that

  13. Computer assisted instruction on "learning nutrition flags for deaf 5th grade and 6th grad students": effectiveness of instruction.

    PubMed

    Srisorachatr, Suwat; Huadong, Yotsinee; Hudthagosol, Chatrapa; Danthanavanich, Suksiri

    2013-12-01

    Deaf students are of a number of under privilege group for whom there are limited resources for their use, related to health including nutrition. The purpose of this research was to create computer-assisted instruction for "nutrition flags" for 5 and 6th grade students. The content of nutrition included the concept of a healthy balance diets and portion sizes of each food group. The content and pictures for computer-assisted instruction came from existing curriculum, and focused on nutritional content. The contents in this instruction were divided into three units according to students' learning capacity. The story boards were developed by staff including nutritionists, Thai sign language interpreters, and deaf students. Then, the contents and nutrition vocabulary were translated into Thai sign language. After recording the sign language on video, this material was merged with the contents and converted into a computer program. The computer assisted instruction was tested with students from Nakon Pathom School for the Deaf The first trial was conducted with three students, the second with five students, and the third with 15 students during the academic year 2009. The computer- assisted instruction was revised until it met the standard criteria of 80/80. Effectiveness testing was carried out with 36 students for five consecutive days. On the first day, the pre-test was completed, and on days 2-4, the students performed self-study and completed the exercises for units 1-3, with 50 minutes spent on each unit. The post-test was completed on the last day. The study was conducted during the 2010 academic year Data analysis was performed using the t-test. The results showed an effectiveness of 81.85/82.22, which was higher than the standard criteria of 80/80. The post-test average score was higher than the pre-test average score with a statistical significance level at p < 0.0001. Suggestions for instruction for the deaf are that the length of the instruction in each

  14. Additive Manufacturing Infrared Inspection

    NASA Technical Reports Server (NTRS)

    Gaddy, Darrell; Nettles, Mindy

    2015-01-01

    The Additive Manufacturing Infrared Inspection Task started the development of a real-time dimensional inspection technique and digital quality record for the additive manufacturing process using infrared camera imaging and processing techniques. This project will benefit additive manufacturing by providing real-time inspection of internal geometry that is not currently possible and reduce the time and cost of additive manufactured parts with automated real-time dimensional inspections which deletes post-production inspections.

  15. EUV blank inspection

    NASA Astrophysics Data System (ADS)

    Peters, J. H.; Tonk, C.; Spriegel, D.; Han, Hak-Seung; Cho, Wonil; Wurm, Stefan

    2008-04-01

    One of the major topics for the introduction of extreme ultraviolet (EUV) technology is the availability of defect-free masks. From the mask makers' perspective, the quality of the incoming blank material is one of the key ingredients impacting the yield of structured masks. Besides flatness and layer thickness uniformity, the number of defects determines the final quality of the mask delivered to the customer for printing. Defects within the layers of optical blanks have shown that they have a growing impact on the mask structuring process, well below the usual defect specifications of the blanks. It is expected that this finding will also hold true for material layers above the multi-layer. In addition to printing performance, EUV masks need to have a defect-free multi-layer. While this layer is easily accessible during blank production, mask makers usually acquire the complete blank stacks with or without the coated resist. Incoming blank inspection, therefore, must check the quality of the complete stack without destroying any of the functionality of these layers. Siemens and AMTC have jointly developed a blank inspection tool that has been installed in AMTC's Dresden facility and that allows the screening of an EUV blank under these boundary conditions. Previously, SEMATECH successfully installed an M7360 from Lasertec in its Mask Blank Development Center (MBDC) in Albany, NY, that shows much better sensitivity data than SEMATECH's earlier tool, the Lasertec M1350. This paper describes the early performance of the Siemens DF-40XP on programmed multi-layer defect blanks and regular blanks and compares it to that of the existing tools at the SEMATECH MBDC.

  16. In-service pressure vessel inspections

    NASA Astrophysics Data System (ADS)

    Fields, Marvin

    1998-03-01

    Eliminate any doubt that the vessel condition is suitable for continued operation through a planned inspection program that can mitigate or avoid failure of a pressure vessel due to corrosion or erosion. Proper inspection and documentation help you in identifying the problem and confirming the actual thickness leading to properly correcting deficiencies. Proper inspection is the antidote for any inspection program. Vessel life can be extended, risk can be minimized and unscheduled downtime can be prevented by implementing and managing your inspection program. A successful program includes maintaining accurate records, conducting inspections in regular intervals, and taking proper action on deficiencies. Therefore, you will know what you have and the condition of your equipment. Pressure vessel inspections can be classified into two general categories: surface inspection and volumetric inspection. Surface techniques for vessels include two of the commonest types: dye-penetrant and magnetic particle testing. Board qualified inspectors are required to perform these two tests. Volumetric techniques for vessels include three common types: ultrasonic testing, eddy current testing, and radiography. At Abbott the use of advanced NDE (non destructive examination) techniques, ultrasonic b-scan, has provided us with the proper tools to obtain the above objectives. We have been applying ultrasonic b-scan utilizing a pulse echo pitch catch technique to provide us with essential data on each of our pressure vessels. This reduces equipment downtime because the nondestructive examination usually takes place while our vessels are in service. As inspections take place we are able to view a real time image of the defective discontinuities on a video monitor. This ultrasonic b-scan technique is allowing us to perform fast accurate examinations covering up to 96% of the surface area of each pressure vessel.

  17. PREFACE: NC-AFM 2003: Proceedings of the 6th International Conference on Non-contact Atomic Force Microscopy

    NASA Astrophysics Data System (ADS)

    Reichling, Michael

    2004-02-01

    Direct nanoscale and atomic resolution imaging is a key issue in nanoscience and nanotechnology. The invention of the dynamic force microscope in the early 1990s was an important step forward in this direction as this instrument provides a universal tool for measuring the topography and many other physical and chemical properties of surfaces at the nanoscale. Operation in the so-called non-contact mode now allows direct atomic resolution imaging of electrically insulating surfaces and nanostructures which has been an unsolved problem during the first decade of nanotechnology. Today, we face a most rapid development of the technique and an extension of its capabilities far beyond imaging; atomically resolved force spectroscopy provides information about local binding properties and researchers now develop sophisticated schemes of force controlled atomic manipulation with the tip of the force microscope. Progress in the field of non-contact force microscopy is discussed at the annually held NC-AFM conferences that are part of a series started in 1998 with a meeting in Osaka, Japan. The 6th International Conference on Non-contact Atomic Force Microscopy took place in Dingle, Ireland, from 31 August to 3 September 2003 and this special issue is a compilation of the original publications of work presented at this meeting. The papers published here well reflect recent achievements, current trends and some of the challenging new directions in non-contact force microscopy that have been discussed during the most stimulating conference days in Dingle. Fundamental aspects of forces and dissipation relevant in imaging and spectroscopy have been covered by experimental and theoretical contributions yielding a more detailed understanding of tip--surface interaction in force microscopy. Novel and improved imaging and spectroscopy techniques have been introduced that either improve the performance of force microscopy or pave the way towards new functionalities and applications

  18. SB6.0: The 6th International meeting on Synthetic Biology, July 9-11, 2013

    SciTech Connect

    Kahl, Linda J.

    2015-04-23

    The Synthetic Biology conference series (SBx.0) is the preeminent academic meeting in synthetic biology. Organized by the BioBricks Foundation, the SBx.0 conference series brings together leading researchers, students, industry executives, and policy makers from around the world to share, consider, debate, and plan efforts to make biology easier to engineer. Historically held every two years, the SBx.0 conferences are held in alternating locations in the United States, Europe, and Asia to encourage global participation and collaboration so that the ramifications of synthetic biology research and development are most likely to be safe ethical, and beneficial. On 9-11 July 2013, the 6th installment of the synthetic biology conference series (SB6.0) was held on the campus of Imperial College London (http://sb6.biobricks.org). The SB6.0 conference was attended by over 700 people, and many more were able to participate via video digital conference (http://sb6.biobricks.org/digital-conference/). Over the course of three days, the SB6.0 conference agenda included plenary sessions, workshops, and poster presentations covering topics ranging from the infrastructure needs arising when “Systematic Engineering Meets Biological Complexity” and design-led considerations for “Connecting People and Technologies” to discussions on “Engineering Biology for New Materials,” “Assessing Risk and Managing Biocontainment,” and “New Directions for Energy and Sustainability.” The $10,150 grant awarded by the U.S. Department of Energy (DE-SC0010233) to the BioBricks Foundation was used to provide partial reimbursement for the travel expenses of leading researchers from the United States to speak at the SB6.0 conference. A total of $9,450 was used to reimburse U.S. speakers for actual expenses related to the SB6.0 conference, including airfare (economy or coach only), ground transportation, hotel, and registration fees. In addition, $700 of the grant was used to offset

  19. Dimensional Regularization is Generic

    NASA Astrophysics Data System (ADS)

    Fujikawa, Kazuo

    The absence of the quadratic divergence in the Higgs sector of the Standard Model in the dimensional regularization is usually regarded to be an exceptional property of a specific regularization. To understand what is going on in the dimensional regularization, we illustrate how to reproduce the results of the dimensional regularization for the λϕ4 theory in the more conventional regularization such as the higher derivative regularization; the basic postulate involved is that the quadratically divergent induced mass, which is independent of the scale change of the physical mass, is kinematical and unphysical. This is consistent with the derivation of the Callan-Symanzik equation, which is a comparison of two theories with slightly different masses, for the λϕ4 theory without encountering the quadratic divergence. In this sense the dimensional regularization may be said to be generic in a bottom-up approach starting with a successful low energy theory. We also define a modified version of the mass independent renormalization for a scalar field which leads to the homogeneous renormalization group equation. Implications of the present analysis on the Standard Model at high energies and the presence or absence of SUSY at LHC energies are briey discussed.

  20. Chemical Thermodynamics: Basic Theory and Methods, 6th Edition (by Irving M. Klotz and Robert M. Rosenberg)

    NASA Astrophysics Data System (ADS)

    Somer, Frank, Jr.

    2001-06-01

    It seems to me that this text is best suited to a first graduate course or an advanced undergraduate course in thermodynamics. I have used it in a master's-level course, where it was quite well received by the students. I also regularly refer my undergraduate physical chemistry students to this book when they ask for a more detailed discussion of certain topics than is given their "p-chem" text or are looking for some additional practice problems, and they seem to find it very accessible. This book does not assume any previous exposure to thermodynamics, and so could presumably be used for the relevant parts of an introductory course in physical chemistry. It is not quite as pedantic as the usual physical chemistry tomes, though, so in this case the instructor should be careful to provide adequate context for the excellent formal development provided in this text.

  1. Piping inspection instrument carriage

    SciTech Connect

    Zollinger, W.T.; Treanor, R.C.

    1993-09-20

    This invention is comprised of a pipe inspection instrument carriage for use with a pipe crawler or other locomotion means for performing internal inspections of piping surfaces. The carriage has a front leg assembly, a rear leg assembly and a central support connecting the two assemblies and for mounting an instrument arm having inspection instruments. The instrument arm has means mounted distally thereon for axially aligning the inspection instrumentation and means for extending the inspection instruments radially outward to operably position the inspection instruments on the piping interior. Also, the carriage has means for rotating the central support and the front leg assembly with respect to the rear leg assembly so that the inspection instruments azimuthally scan the piping interior. The instrument carriage allows performance of all piping inspection operations with a minimum of moving parts, thus decreasing the likelihood of performance failure.

  2. PREFACE: MEM11: The 6th International Workshop on Mechanical-Electromagnetic Properties of Composite Superconductors (Okinawa, Japan, 5-7 December 2011) MEM11: The 6th International Workshop on Mechanical-Electromagnetic Properties of Composite Superconductors (Okinawa, Japan, 5-7 December 2011)

    NASA Astrophysics Data System (ADS)

    Awaji, Satoshi; Osamura, Kozo; Hampshire, Damian

    2012-05-01

    The effect of stress and strain on the electromagnetic properties of superconducting composite conductors is one of the key issues for the practical application of superconductivity. To discuss these subjects thoroughly, the International Workshop on Mechanical-Electromagnetic Properties of Composite Superconductors (MEM) has been held regularly since 2001. The 6th workshop (MEM11) was held in Okinawa, Japan in 2011, which was the centennial of the discovery of superconductivity by Professor Kamerlingh Onnes, as well as the 25th anniversary of the discovery of high temperature superconductors (HTS). Although it was originally planned that MEM11 be held in Mito, the workshop venue was changed because of the serious disaster in the north of Japan on 11 March 2011. Sixty five scientists participated in this specialized workshop. Fifty six papers were presented in the following six sessions: (1) Intrinsic strain effects on low temperature superconductors (LTS) and HTS, (2) The International Thermonuclear Experimental Reactor (ITER), (3) Strain evaluation by quantum beams, (4) Flux pinning properties of HTS, (5) Standardization and the Versailles Project on Advanced Materials and Standards (VAMAS) and (6) High field magnets. Several large topics were presented and discussed at the workshop: the important progress in methods for non-invasive measurements of the local strain exerted on the superconducting components in superconducting wires and cables using quantum beam techniques. This approach provides powerful tools for investigating the effect of strain in composite superconductors; the intrinsic strain effects in LTS and HTS in the reversible strain region. Recently, it has become easier to determine quantitatively the strain dependence of critical current when the local strain is measured directly, and the mechanical and electromagnetic properties of the superconductors used in the ITER tokamak. This was a major topic at the workshop since the superconducting

  3. Prognostic Discrepancy of the 6th and 7th UICC N Classification for Lymph Node Staging in Gastric Cancer Patients after Curative Resection

    PubMed Central

    Oh, Sung Jin; Suh, Byoung Jo; Park, Jong Kwon; Oh, Sung Don; Yu, Hang Jong

    2017-01-01

    Background The validity of N classification of the 7th edition of the American Joint Committee on Cancer/Union Internationale contre le Cancer (AJCC/UICC) tumor-node-metastasis (TNM) staging system is still under debate. The purpose of this study was to evaluate the prognostic efficacy of the 7th edition of the AJCC/UICC TNM staging system (focusing on N stage), in comparison with the 6th edition, at a single Eastern institution. Methods We analyzed 1,435 patients with gastric cancer who underwent curative resection performed from September 1998 to August 2003 at the Memorial Jin-Pok Kim Korea Gastric Cancer Center. We analyzed the survival rate of the patients according to the AJCC/UICC 6th and 7th editions, and compared each stage, focusing on N stage. Results Significant differences in the 5-year survival rates were observed between the 6th and the 7th AJCC/UICC staging system. In the 6th edition staging system, the Kaplan-Meier curves discriminated each N stage significantly. In contrast, there was no difference in terms of survival curves for N stage according to the 7th edition, especially between N1 and N2: the Kaplan-Meier plots of survival curves between N1 (77.0%) and N2 (78.1%) stages overlapped significantly (p < 0.05). Conclusion Although the 7th UICC staging system is a more detailed and sophisticated system in the T category, there was no prognostic significance between the pN1 and pN2 stages according to our data. Therefore, we suggest establishing a new UICC staging system taking into consideration the application of the N stage. PMID:28203165

  4. The Earth Microbiome Project: Meeting report of the “1st EMP meeting on sample selection and acquisition” at Argonne National Laboratory October 6th 2010.

    PubMed Central

    Gilbert, Jack A.; Meyer, Folker; Jansson, Janet; Gordon, Jeff; Pace, Norman; Tiedje, James; Ley, Ruth; Fierer, Noah; Field, Dawn; Kyrpides, Nikos; Glöckner, Frank-Oliver; Klenk, Hans-Peter; Wommack, K. Eric; Glass, Elizabeth; Docherty, Kathryn; Gallery, Rachel; Stevens, Rick; Knight, Rob

    2010-01-01

    This report details the outcome the first meeting of the Earth Microbiome Project to discuss sample selection and acquisition. The meeting, held at the Argonne National Laboratory on Wednesday October 6th 2010, focused on discussion of how to prioritize environmental samples for sequencing and metagenomic analysis as part of the global effort of the EMP to systematically determine the functional and phylogenetic diversity of microbial communities across the world. PMID:21304728

  5. Update on the U.S. Army TARDEC Power and Energy P&E SIL Program: Progress since the 6th AECV (June 2005 to Present)

    DTIC Science & Technology

    2007-06-01

    energy dissipaters were installed and the diagnostics and data acquisition system was upgraded. Since one of the two traction motor- dyno pairs was...ion system identical to one installed in HERMIT. New energy dissipaters were installed and the diagnostics and data acquisition system was upgraded...UPDATE ON THE U.S. ARMY TARDEC POWER AND ENERGY P&E SIL PROGRAM Progress since the 6th AECV (June 2005 to Present) Nancy Saxon*, Eugene

  6. Development of Inspection and Investigation Techniques to Prepare Debris Flow in Urban Areas

    NASA Astrophysics Data System (ADS)

    Seong, Joo-Hyun; Jung, Min-Hyeong; Park, Kyung-Han; An, Jai-Wook; Kim, Jiseong

    2017-04-01

    Due to the urban development, various facilities are located in mountainous areas near the city, and the damage to the occurrence of the debris flow is increasing in the urban area. However, quantitative inspection and investigation techniques are not sufficient for preparing debris flow in the urban area around the world. Therefore, in this study, we developed the debris flow inspection and investigation techniques, which are suitable for urban characteristics, regarding the soil hazard prevention and restoration in urban area. First, the inspection and investigation system is divided into the daily occurrence and the occurrence of the soil hazard event, and the inspection / investigation flow chart were developed based on the kind of inspection and correspondence required for each situation. The types of inspections applied in this study were determined as daily inspection, regular inspections, special emergency inspection, damage emergency inspection and In-depth safety inspection. The management agency, term of inspection, objects to be inspected, and contents of inspection work were presented according to type of each inspection. The daily inspection routinely checks for signs of collapse and conditions of facilities in urban areas which show vulnerability for soil hazard and that are conducted from the management agency. In the case of regular inspection, an expert for soil hazards regularly conducts detailed visual surveys on mountainous areas, steep slopes, prevention facilities and adjacent facilities in vulnerable areas. On the other hand, it was decided that the emergency inspection is carried out in the event of the occurrence of vulnerable element or soil hazards. Acknowledgement This study was conducted with the research iund support by the constructiontechnology research project of the Ministry of Land, Infrastructure and Transport (project number 16SCIP-B069989-04)

  7. Advancements in Underwater Inspection

    DTIC Science & Technology

    1989-05-01

    Guard. For example, the Underwater Survey in Lieu of Dry Dock program, mobile offshore drilling unit (MODU) underwater hull inspection, tension leg...could be used to perform various types of underwater inspection on tension leg platform (TLP) tendons and templates. Understanding inspection...intervention (Ref. 6). This technique has application to the inspection of the mooring chains and terminations on floating facilities, and tension leg

  8. Archeomagnetic Intensity Variations During the 6th Millennium BC in the Middle East: New Data from Yarim Tepe II (Northern Iraq)

    NASA Astrophysics Data System (ADS)

    Akimova, S.; Gallet, Y.; Amirov, S.

    2015-12-01

    During the seventies, Soviet archeologists conducted in Northern Iraq excavations of several ancient settlements dated from the Pottery Late Neolithic period (7th and 6th millennia BC). A very large collection of artifacts unearthed from these sites, in particular several thousands of well-documented pottery fragments, is now stored at the Archeological Institute in Moscow. We collected a time-sequential series of groups of potsherds from the multilayered settlement called Yarim Tepe II dated to the Halaf period (6th millennium BC). Each group comprises a minimum of 3 potsherds (up to 10) found within a same archeological layer, typically a thickness of about 20 cm. Altogether, the fragment groups encompass the entire 7-m thick stratigraphic sequence of Yarim Tepe II. We will present our first archeointensity results obtained using the experimental protocol developed for the Triaxe magnetometer, taking into account the effects of both the thermoremanent magnetization (TRM) anisotropy and the cooling rate dependence on TRM acquisition. The new data help to better constrain the geomagnetic field intensity variations in the Middle East during the 6th millennium BC. Thanks to the comparison with other datasets from Bulgaria and Syria, the new archeointensity results provide evidence for the occurrence of very rapid geomagnetic field intensity variations around 5500 BC.

  9. Electronic Inspection of Beef

    NASA Technical Reports Server (NTRS)

    Anselmo, Victor J.; Gammell, Paul M.; Clark, Jerry

    1987-01-01

    Two proposed methods for grading beef quality based on inspection by electronic equipment: one method uses television camera to generate image of a cut of beef as customer sees it; other uses ultrasonics to inspect live animal or unsliced carcasses. Both methods show promise for automated meat inspection.

  10. Software Formal Inspections Guidebook

    NASA Technical Reports Server (NTRS)

    1993-01-01

    The Software Formal Inspections Guidebook is designed to support the inspection process of software developed by and for NASA. This document provides information on how to implement a recommended and proven method for conducting formal inspections of NASA software. This Guidebook is a companion document to NASA Standard 2202-93, Software Formal Inspections Standard, approved April 1993, which provides the rules, procedures, and specific requirements for conducting software formal inspections. Application of the Formal Inspections Standard is optional to NASA program or project management. In cases where program or project management decide to use the formal inspections method, this Guidebook provides additional information on how to establish and implement the process. The goal of the formal inspections process as documented in the above-mentioned Standard and this Guidebook is to provide a framework and model for an inspection process that will enable the detection and elimination of defects as early as possible in the software life cycle. An ancillary aspect of the formal inspection process incorporates the collection and analysis of inspection data to effect continual improvement in the inspection process and the quality of the software subjected to the process.

  11. Electronic Inspection of Beef

    NASA Technical Reports Server (NTRS)

    Anselmo, Victor J.; Gammell, Paul M.; Clark, Jerry

    1987-01-01

    Two proposed methods for grading beef quality based on inspection by electronic equipment: one method uses television camera to generate image of a cut of beef as customer sees it; other uses ultrasonics to inspect live animal or unsliced carcasses. Both methods show promise for automated meat inspection.

  12. Information and communication technology: students' health education in 1st- to 6th-grade South Korea elementary schools.

    PubMed

    Lee, Eunjoo; Park, Hyejin; Whyte, James; Jeong, Eunhoe

    2013-09-01

    The purposes of this study were to (1) identify school nurses' awareness of information and communication technology (ICT) use in students' health education and (2) explore the barriers or reasons for the adoption of ICT in school nursing practice, while (3) presenting strategies to speed ICT diffusion and dissemination into practice. For data collection, 209 primary school nurses in K province of Korea were selected and e-mailed the questionnaires. Collected data were analyzed as frequency, percentages, and chi-square tests. The major reasons to adopt ICT were increasing school nurses' confidence in providing health education and improving teaching methods using diverse multimedia. The major barriers to utilization of ICT were lack of time for preparation of educational materials, lack of software availability, and lack of computer skills of school nurses and students. Several strategies were suggested to speed the diffusion of ICT into students' health education, such as integrating a health education course into regular curriculum. It is important to identify barriers and reasons for adoption of ICT in school nursing. In addition, strategies should be emphasized that result in more rapid diffusion of these technologies in school nursing practice. © 2013, American School Health Association.

  13. Software Formal Inspections Standard

    NASA Technical Reports Server (NTRS)

    1993-01-01

    This Software Formal Inspections Standard (hereinafter referred to as Standard) is applicable to NASA software. This Standard defines the requirements that shall be fulfilled by the software formal inspections process whenever this process is specified for NASA software. The objective of this Standard is to define the requirements for a process that inspects software products to detect and eliminate defects as early as possible in the software life cycle. The process also provides for the collection and analysis of inspection data to improve the inspection process as well as the quality of the software.

  14. School nurse inspections improve handwashing supplies.

    PubMed

    Ramos, Mary M; Schrader, Ronald; Trujillo, Rebecca; Blea, Mary; Greenberg, Cynthia

    2011-06-01

    Handwashing in the school setting is important for infectious disease control, yet maintaining adequate handwashing supplies is often made difficult by lack of funds, limited staff time, and student vandalism. This study measured the availability of handwashing supplies for students in New Mexico public schools and determined the impact of scheduled school nurse inspections on the availability of handwashing supplies. Participating school districts in New Mexico were matched by size and randomized into intervention and control groups. Baseline inspections were conducted in November 2008 followed by 2 subsequent bimonthly inspections. For each student bathroom, the presence or absence of soap and either paper towels or hand dryers was indicated on an inspection checklist. The intervention group reported findings to the New Mexico Department of Health (NMDOH) and to school administrative and custodial staff requesting that any identified problems be addressed. The control group reported inspection findings to the NMDOH only. Descriptive analyses were conducted to determine the proportion of bathrooms with soap and either paper towels or hand dryers. Comparisons were made between the intervention schools and the control schools at baseline and during the intervention period. The intervention group had significantly higher probability of bathrooms being supplied with soap (p < .05) and paper towels/hand dryers (p < .02) during the intervention period. Regularly scheduled school nurse inspections of hand hygiene supplies, with reporting to appropriate school officials, can improve the availability of handwashing supplies for students. © 2011, American School Health Association.

  15. School Nurse Inspections Improve Handwashing Supplies

    PubMed Central

    Ramos, Mary M.; Schrader, Ronald; Trujillo, Rebecca; Blea, Mary; Greenberg, Cynthia

    2013-01-01

    BACKGROUND Handwashing in the school setting is important for infectious disease control, yet maintaining adequate handwashing supplies is often made difficult by lack of funds, limited staff time, and student vandalism. This study measured the availability of handwashing supplies for students in New Mexico public schools and determined the impact of scheduled school nurse inspections on the availability of handwashing supplies. METHODS Participating school districts in New Mexico were matched by size and randomized into intervention and control groups. Baseline inspections were conducted in November 2008 followed by 2 subsequent bimonthly inspections. For each student bathroom, the presence or absence of soap and either paper towels or hand dryers was indicated on an inspection checklist. The intervention group reported findings to the New Mexico Department of Health (NMDOH) and to school administrative and custodial staff requesting that any identified problems be addressed. The control group reported inspection findings to the NMDOH only. Descriptive analyses were conducted to determine the proportion of bathrooms with soap and either paper towels or hand dryers. Comparisons were made between the intervention schools and the control schools at baseline and during the intervention period. RESULTS The intervention group had significantly higher probability of bathrooms being supplied with soap (p < .05) and paper towels/hand dryers (p < .02) during the intervention period. CONCLUSIONS Regularly scheduled school nurse inspections of hand hygiene supplies, with reporting to appropriate school officials, can improve the availability of handwashing supplies for students. PMID:21592131

  16. [Execution and quality of attention paid to medical doctoral theses at the faculty of medicine at the University of Würzburg as seen by the doctoral candidates in their 5th and 6th year of study].

    PubMed

    Diez, C; Arkenau, C; Meyer-Wentrup, F

    2002-07-01

    The significance of a doctoral thesis in medicine has been discussed controversially among medical students and faculty members. We examined in a brief but comprehensive study how medical students evaluate their research activities and whether or not alternative thesis models should be implemented. A questionnaire comprising 50 questions was evaluated from 160 5th and 6th year medical students at the University of Wuerzburg. Almost two-thirds of our interviewees started working on a thesis project at the beginning of the 4th year of study. 59 % of our participants reported to have neglected the regular study and 56 % said to have prolonged the regular study due to the work on a thesis. Despite considerable variation, the median time spent weekly on a thesis project was 10 hours, independent of where the students worked. The median grade of satisfaction during the whole thesis was rated at 6.5 as assessed on an analogous scale from 1-10 (very satisfied). The research results from 94 students contributed to 164 articles (already published or in press) and the results of 110 students were presented at scientific meetings. Only 50 % of our interviewees were pleased with their published output and the importance of student research activities for the overall German biomedical research was rated 4.4 as assessed on an analogous scale from 1-10 (very important). 70 % of our interviewees preferred defined research periods and 47 % would apply for dual-degree research programmes. The scientific significance of a MD thesis in comparison to a PhD thesis was rated at 2.1 on an analogous scale from 1-5 (5 = equally significant). The current German research model might be modified and defined research periods and dual-degree research programmes as a one possible alternative should be considered.

  17. Sparsity regularized image reconstruction

    NASA Astrophysics Data System (ADS)

    Hero, Alfred

    2015-03-01

    Most image reconstruction problems are under-determined: there are far more pixels to be resolved than there are measurements available. This means that the image space has more degrees of freedom than the measurement space. To make headway in such under-determined image reconstruction problems one must either incorporate domain knowledge or regularize. Domain knowledge restricts the size of the image space while regularization introduces bias, e.g., by forcing the reconstructed image to be smooth or have limited support. Both approaches are equivalent and can be interpreted as making the image sparse in some domain. This paper will provide a selective overview of some of the principal methods of sparsity regularized image reconstruction.

  18. Regular phantom black holes.

    PubMed

    Bronnikov, K A; Fabris, J C

    2006-06-30

    We study self-gravitating, static, spherically symmetric phantom scalar fields with arbitrary potentials (favored by cosmological observations) and single out 16 classes of possible regular configurations with flat, de Sitter, and anti-de Sitter asymptotics. Among them are traversable wormholes, bouncing Kantowski-Sachs (KS) cosmologies, and asymptotically flat black holes (BHs). A regular BH has a Schwarzschild-like causal structure, but the singularity is replaced by a de Sitter infinity, giving a hypothetic BH explorer a chance to survive. It also looks possible that our Universe has originated in a phantom-dominated collapse in another universe, with KS expansion and isotropization after crossing the horizon. Explicit examples of regular solutions are built and discussed. Possible generalizations include k-essence type scalar fields (with a potential) and scalar-tensor gravity.

  19. Regularized Structural Equation Modeling.

    PubMed

    Jacobucci, Ross; Grimm, Kevin J; McArdle, John J

    A new method is proposed that extends the use of regularization in both lasso and ridge regression to structural equation models. The method is termed regularized structural equation modeling (RegSEM). RegSEM penalizes specific parameters in structural equation models, with the goal of creating easier to understand and simpler models. Although regularization has gained wide adoption in regression, very little has transferred to models with latent variables. By adding penalties to specific parameters in a structural equation model, researchers have a high level of flexibility in reducing model complexity, overcoming poor fitting models, and the creation of models that are more likely to generalize to new samples. The proposed method was evaluated through a simulation study, two illustrative examples involving a measurement model, and one empirical example involving the structural part of the model to demonstrate RegSEM's utility.

  20. Development of the EURITRACK tagged neutron inspection system

    NASA Astrophysics Data System (ADS)

    Perot, B.; Carasco, C.; Bernard, S.; Mariani, A.; Szabo, J.-L.; Mercier, E.; Sannie, G.; Viesti, G.; Nebbia, G.; Pesente, S.; Lunardon, M.; Moretto, S.; Fabris, D.; Zenoni, A.; Bonomi, G.; Donzella, A.; Fontana, A.; Boghen, G.; Valkovic, V.; Sudac, D.; Moszynski, M.; Batsch, T.; Gierlik, M.; Woski, D.; Klamra, W.; Isaksson, P.; Le Tourneur, P.; Lhuissier, M.; Colonna, A.; Tintori, C.; Peerani, P.; Sequeira, V.; Salvato, M.

    2007-08-01

    The EURopean Illicit TRAfficing Countermeasures Kit (EURITRACK) project is part of the 6th European Union Framework Program. It aims at developing a Tagged Neutron Inspection System (TNIS) to detect illicit materials, such as explosives and narcotics, in cargo containers. Fast neutron induced reactions produce specific gamma-rays used to determine the chemical composition of the inspected material. The associated particle technique is employed to precisely locate the interaction points of the neutrons. A new deuterium-tritium neutron generator has been developed, including a pixelized alpha particle detector. The TNIS also comprises high-efficiency fast neutron and gamma-ray detectors, a dedicated front-end electronics and an integrated software to entirely drive the system and automatically process the data. Most components have been integrated during last months at Institute Ruder Boskovic, in Zagreb, Croatia. An overview of the TNIS and of its preliminary performances is presented.

  1. Synchronization of Regular Automata

    NASA Astrophysics Data System (ADS)

    Caucal, Didier

    Functional graph grammars are finite devices which generate the class of regular automata. We recall the notion of synchronization by grammars, and for any given grammar we consider the class of languages recognized by automata generated by all its synchronized grammars. The synchronization is an automaton-related notion: all grammars generating the same automaton synchronize the same languages. When the synchronizing automaton is unambiguous, the class of its synchronized languages forms an effective boolean algebra lying between the classes of regular languages and unambiguous context-free languages. We additionally provide sufficient conditions for such classes to be closed under concatenation and its iteration.

  2. Manifold Regularized Reinforcement Learning.

    PubMed

    Li, Hongliang; Liu, Derong; Wang, Ding

    2017-01-27

    This paper introduces a novel manifold regularized reinforcement learning scheme for continuous Markov decision processes. Smooth feature representations for value function approximation can be automatically learned using the unsupervised manifold regularization method. The learned features are data-driven, and can be adapted to the geometry of the state space. Furthermore, the scheme provides a direct basis representation extension for novel samples during policy learning and control. The performance of the proposed scheme is evaluated on two benchmark control tasks, i.e., the inverted pendulum and the energy storage problem. Simulation results illustrate the concepts of the proposed scheme and show that it can obtain excellent performance.

  3. Geometry of spinor regularization

    NASA Technical Reports Server (NTRS)

    Hestenes, D.; Lounesto, P.

    1983-01-01

    The Kustaanheimo theory of spinor regularization is given a new formulation in terms of geometric algebra. The Kustaanheimo-Stiefel matrix and its subsidiary condition are put in a spinor form directly related to the geometry of the orbit in physical space. A physically significant alternative to the KS subsidiary condition is discussed. Derivations are carried out without using coordinates.

  4. Seeking a Regularity.

    ERIC Educational Resources Information Center

    Sokol, William

    This autoinstructional unit deals with the phenomena of regularity in chemical behavior. The prerequisites suggested are two other autoinstructional lessons (Experiments 1 and 2) identified in the Del Mod System as SE 018 020 and SE 018 023. The equipment needed is listed and 45 minutes is the suggested time allotment. The Student Guide includes…

  5. 6th Annual Symposium on Self-Monitoring of Blood Glucose (SMBG) Applications and Beyond, April 25–27, 2013, Riga, Latvia

    PubMed Central

    Schlaeger, Christof; Hinzmann, Rolf

    2013-01-01

    Abstract International experts in the fields of diabetes, diabetes technology, endocrinology, and pediatrics gathered for the 6th Annual Symposium on Self-Monitoring of Blood Glucose (SMBG) Applications and beyond. The aim of this meeting was to continue setting up a global network of experts in this field and provide an international platform for exchange of ideas to improve life for people with diabetes. The 2013 meeting comprised a comprehensive scientific program, parallel interactive workshops, and two keynote lectures. All these discussions were intended to help identify gaps and areas where further scientific work and clinical studies are warranted. PMID:24074038

  6. 4H-Chromene-based anticancer agents towards multi-drug resistant HL60/MX2 human leukemia: SAR at the 4th and 6th positions.

    PubMed

    Puppala, Manohar; Zhao, Xinghua; Casemore, Denise; Zhou, Bo; Aridoss, Gopalakrishnan; Narayanapillai, Sreekanth; Xing, Chengguo

    2016-03-15

    4H-Chromene-based compounds, for example, CXL017, CXL035, and CXL055, have a unique anticancer potential that they selectively kill multi-drug resistant cancer cells. Reported herein is the extended structure-activity relationship (SAR) study, focusing on the ester functional group at the 4th position and the conformation at the 6th position. Sharp SARs were observed at both positions with respect to cellular cytotoxic potency and selectivity between the parental HL60 and the multi-drug resistant HL60/MX2 cells. These results provide critical guidance for future medicinal optimization. Copyright © 2016. Published by Elsevier Ltd.

  7. 6(th) Annual Symposium on Self-Monitoring of Blood Glucose (SMBG) applications and beyond, April 25-27, 2013, Riga, Latvia.

    PubMed

    Alzaid, Aus; Schlaeger, Christof; Hinzmann, Rolf

    2013-12-01

    International experts in the fields of diabetes, diabetes technology, endocrinology, and pediatrics gathered for the 6(th) Annual Symposium on Self-Monitoring of Blood Glucose (SMBG) Applications and beyond. The aim of this meeting was to continue setting up a global network of experts in this field and provide an international platform for exchange of ideas to improve life for people with diabetes. The 2013 meeting comprised a comprehensive scientific program, parallel interactive workshops, and two keynote lectures. All these discussions were intended to help identify gaps and areas where further scientific work and clinical studies are warranted.

  8. Optical fiber inspection system

    DOEpatents

    Moore, Francis W.

    1987-01-01

    A remote optical inspection system including an inspection head. The inspection head has a passageway through which pellets or other objects are passed. A window is provided along the passageway through which light is beamed against the objects being inspected. A plurality of lens assemblies are arranged about the window so that reflected light can be gathered and transferred to a plurality of coherent optical fiber light guides. The light guides transfer the light images to a television or other image transducer which converts the optical images into a representative electronic signal. The electronic signal can then be displayed on a signal viewer such as a television monitor for inspection by a person. A staging means can be used to support the objects for viewing through the window. Routing means can be used to direct inspected objects into appropriate exit passages for accepted or rejected objects. The inspected objects are advantageously fed in a singular manner to the staging means and routing means. The inspection system is advantageously used in an enclosure when toxic or hazardous materials are being inspected.

  9. Optical fiber inspection system

    DOEpatents

    Moore, F.W.

    1985-04-05

    A remote optical inspection system including an inspection head. The inspection head has a passageway through which pellets or other objects are passed. A window is provided along the passageway through which light is beamed against the objects being inspected. A plurality of lens assemblies are arranged about the window so that reflected light can be gathered and transferred to a plurality of coherent optical fiber light guides. The light guides transfer the light images to a television or other image transducer which converts the optical images into a representative electronic signal. The electronic signal can then be displayed on a signal viewer such as a television monitor for inspection by a person. A staging means can be used to support the objects for viewing through the window. Routing means can be used to direct inspected objects into appropriate exit passages for accepted or rejected objects. The inspected objects are advantageously fed in a singular manner to the staging means and routing means. The inspection system is advantageously used in an enclosure when toxic or hazardous materials are being inspected. 10 figs.

  10. Krein regularization of QED

    SciTech Connect

    Forghan, B. Takook, M.V.; Zarei, A.

    2012-09-15

    In this paper, the electron self-energy, photon self-energy and vertex functions are explicitly calculated in Krein space quantization including quantum metric fluctuation. The results are automatically regularized or finite. The magnetic anomaly and Lamb shift are also calculated in the one loop approximation in this method. Finally, the obtained results are compared to conventional QED results. - Highlights: Black-Right-Pointing-Pointer Krein regularization yields finite values for photon and electron self-energies and vertex function. Black-Right-Pointing-Pointer The magnetic anomaly is calculated and is exactly the same as the conventional result. Black-Right-Pointing-Pointer The Lamb shift is calculated and is approximately the same as in Hilbert space.

  11. Regularized Hamiltonians and Spinfoams

    NASA Astrophysics Data System (ADS)

    Alesci, Emanuele

    2012-05-01

    We review a recent proposal for the regularization of the scalar constraint of General Relativity in the context of LQG. The resulting constraint presents strengths and weaknesses compared to Thiemann's prescription. The main improvement is that it can generate the 1-4 Pachner moves and its matrix elements contain 15j Wigner symbols, it is therefore compatible with the spinfoam formalism: the drawback is that Thiemann anomaly free proof is spoiled because the nodes that the constraint creates have volume.

  12. Smoking practices, risk perception of smoking, and environmental tobacco smoke exposure among 6th-grade students in Ciudad Juárez, Mexico.

    PubMed

    Bird, Yelena; Moraros, John; Olsen, Larry K; Forster-Cox, Sue; Staines-Orozco, Hugo; Buckingham, Robert W

    2007-02-01

    This study assessed the smoking practices, risk perception of smoking, and environmental tobacco smoke (ETS) exposure among adolescents in Ciudad Juárez, Mexico. We used a cross-sectional method to examine the smoking practices, risk perception of smoking, and ETS exposure of 6th-grade students (N=506), aged 11-13 years, attending six randomly selected middle schools. Schools were classified by school setting (i.e., public vs. private) and socioeconomic status (SES; i.e., low, middle, or high). The results indicated that 6th-grade students attending a public, low-SES school setting in Ciudad Juárez not only exhibited significantly higher rates of ETS exposure at home and in public places (p<.01) but also were more likely to have tried smoking (p<.01) and to be current smokers (p<.01), and were less likely to support a ban on smoking in public places (p<.01), compared with students who attended a private school or a public, middle- or high-SES school setting. These results provide further evidence that public health interventions to prevent initiation of smoking and to assist in smoking cessation among adolescents and to reduce their ETS exposure at home and in public need to target all school-aged students, especially those attending school in a low-SES settings.

  13. Metastatic lymph node ratio, 6th or 7th AJCC edition: witch is the best lymph node classification for esophageal cancer? Prognosis factor analysis in 487 patients

    PubMed Central

    CORAL, Roberto V.; BIGOLIN, André V.; CORAL, Roberto P.; HARTMANN, Antonio; DRANKA, Carolina; ROEHE, Adriana V.

    2015-01-01

    Background The esophageal cancer is one of the most common and aggressive worldwide. Recently, the AJCC changed the staging system, considering, among others, the important role of the lymph node metastasis on the prognosis. Aim To discuss the applicability of different forms of lymph node staging in a western surgical center. Methods Four hundred eighty seven patients with esophageal cancer were enrolled. Three staging systems were evaluated, the 6th and the 7th AJCC editions and the Lymph Node Metastatic Ratio. Results The majority of the cases were squamous cell carcinoma. The mean lymph node sample was eight. Considering the survival, there was no significant difference between the patients when they were classified by the 7th AJCC edition. Analysis of the Lymph Node Metastatic Ratio, just on the group of patients with 0 to 25%, has shown significant difference (p=0,01). The 6th AJCC edition shows the major significant difference between among the classifications evaluated. Conclusion In this specific population, the 7th AJCC edition for esophageal cancer was not able to find differences in survival when just the lymph node analysis was considered. PMID:26176242

  14. Rabies vaccine standards: comparison of the 5th and 6th WHO international reference standards to the USDA veterinary reference standard.

    PubMed

    Hermann, J; Fry, A; Reising, M; Patterson, P; Siev, D; Gatewood, D

    2012-11-06

    Ensuring rabies vaccines are potent and effective is paramount in preventing transmission of this deadly disease and safeguarding public health. Efficacy of human and veterinary vaccines is ensured by evaluating relative potency estimates of the vaccine compared to a rabies reference standard using the National Institutes of Health (NIH) test. Reference vaccines are based on the International Standard for Rabies Vaccine provided by the World Health Organization (WHO). A comparison study was conducted to determine the relative potency of the 5th WHO, 6th WHO, and United States Department of Agriculture's (USDA) 08-14 reference standards using the NIH test. Results from the study demonstrate that the 6th WHO reference standard is approximately twice as potent as the 5th WHO reference when reconstituted to contain 1 IU per ml. Based on these results, the Center for Veterinary Biologics (CVB) doubled the reconstitution volume of USDA veterinary reference 08-14 from 13 ml to 26 ml, for an initial use dilution of 0.7 IU per ml for use by veterinary biologics manufacturers in the NIH test. This study emphasizes the importance of reference standard calibration for use in the National Institutes of Health test.

  15. Regularizing portfolio optimization

    NASA Astrophysics Data System (ADS)

    Still, Susanne; Kondor, Imre

    2010-07-01

    The optimization of large portfolios displays an inherent instability due to estimation error. This poses a fundamental problem, because solutions that are not stable under sample fluctuations may look optimal for a given sample, but are, in effect, very far from optimal with respect to the average risk. In this paper, we approach the problem from the point of view of statistical learning theory. The occurrence of the instability is intimately related to over-fitting, which can be avoided using known regularization methods. We show how regularized portfolio optimization with the expected shortfall as a risk measure is related to support vector regression. The budget constraint dictates a modification. We present the resulting optimization problem and discuss the solution. The L2 norm of the weight vector is used as a regularizer, which corresponds to a diversification 'pressure'. This means that diversification, besides counteracting downward fluctuations in some assets by upward fluctuations in others, is also crucial because it improves the stability of the solution. The approach we provide here allows for the simultaneous treatment of optimization and diversification in one framework that enables the investor to trade off between the two, depending on the size of the available dataset.

  16. Inline inspection of textured plastics surfaces

    NASA Astrophysics Data System (ADS)

    Michaeli, Walter; Berdel, Klaus

    2011-02-01

    This article focuses on the inspection of plastics web materials exhibiting irregular textures such as imitation wood or leather. They are produced in a continuous process at high speed. In this process, various defects occur sporadically. However, current inspection systems for plastics surfaces are able to inspect unstructured products or products with regular, i.e., highly periodic, textures, only. The proposed inspection algorithm uses the local binary pattern operator for texture feature extraction. For classification, semisupervised as well as supervised approaches are used. A simple concept for semisupervised classification is presented and applied for defect detection. The resulting defect-maps are presented to the operator. He assigns class labels that are used to train the supervised classifier in order to distinguish between different defect types. A concept for parallelization is presented allowing the efficient use of standard multicore processor PC hardware. Experiments with images of a typical product acquired in an industrial setting show a detection rate of 97% while achieving a false alarm rate below 1%. Real-time tests show that defects can be reliably detected even at haul-off speeds of 30 m/min. Further applications of the presented concept can be found in the inspection of other materials.

  17. Final FDA inspection manual.

    PubMed

    Donawa, M

    2001-04-01

    For some time now, the only publicly available compliance programme guidance manual on medical device inspections and administrative and enforcement activities has been a draft document. On 7 February 2001, a final guidance document was issued. This article discusses this document and its importance to non-US medical device manufacturers preparing for FDA facility inspections.

  18. Fire Prevention Inspection Procedures.

    ERIC Educational Resources Information Center

    Pribyl, Paul F.

    Lesson plans are provided for a fire prevention inspection course of the Wisconsin Fire Service Training program. Objectives for the course are to enable students to describe and conduct fire prevention inspections, to identify and correct hazards common to most occupancies, to understand the types of building construction and occupancy, and to…

  19. Fire Prevention Inspection Procedures.

    ERIC Educational Resources Information Center

    Pribyl, Paul F.

    Lesson plans are provided for a fire prevention inspection course of the Wisconsin Fire Service Training program. Objectives for the course are to enable students to describe and conduct fire prevention inspections, to identify and correct hazards common to most occupancies, to understand the types of building construction and occupancy, and to…

  20. Reflection on School Inspection

    ERIC Educational Resources Information Center

    Palmer, W. P.

    1992-01-01

    The author was employed as an inspector of education in Nigeria from 1973 to 1978, in what was a completely new system of national inspection. His experience as an inspector has given him a long term interest in educational administration, particularly in relation to the types of school inspection that different countries have in relation to their…

  1. Strongly Regular Graphs,

    DTIC Science & Technology

    1973-10-01

    The theory of strongly regular graphs was introduced by Bose r7 1 in 1963, in connection with partial geometries and 2 class association schemes. One...non adjacent vertices is constant and equal to ~. We shall denote by ~(p) (reap.r(p)) the set of vertices adjacent (resp.non adjacent) to a vertex p...is the complement of .2’ if the set of vertices of ~ is the set of vertices of .2’ and if two vertices in .2’ are adjacent if and only if they were

  2. Flexible sparse regularization

    NASA Astrophysics Data System (ADS)

    Lorenz, Dirk A.; Resmerita, Elena

    2017-01-01

    The seminal paper of Daubechies, Defrise, DeMol made clear that {{\\ell }}p spaces with p\\in [1,2) and p-powers of the corresponding norms are appropriate settings for dealing with reconstruction of sparse solutions of ill-posed problems by regularization. It seems that the case p = 1 provides the best results in most of the situations compared to the cases p\\in (1,2). An extensive literature gives great credit also to using {{\\ell }}p spaces with p\\in (0,1) together with the corresponding quasi-norms, although one has to tackle challenging numerical problems raised by the non-convexity of the quasi-norms. In any of these settings, either superlinear, linear or sublinear, the question of how to choose the exponent p has been not only a numerical issue, but also a philosophical one. In this work we introduce a more flexible way of sparse regularization by varying exponents. We introduce the corresponding functional analytic framework, that leaves the setting of normed spaces but works with so-called F-norms. One curious result is that there are F-norms which generate the ℓ 1 space, but they are strictly convex, while the ℓ 1-norm is just convex.

  3. Regularized versus non-regularized statistical reconstruction techniques

    NASA Astrophysics Data System (ADS)

    Denisova, N. V.

    2011-08-01

    An important feature of positron emission tomography (PET) and single photon emission computer tomography (SPECT) is the stochastic property of real clinical data. Statistical algorithms such as ordered subset-expectation maximization (OSEM) and maximum a posteriori (MAP) are a direct consequence of the stochastic nature of the data. The principal difference between these two algorithms is that OSEM is a non-regularized approach, while the MAP is a regularized algorithm. From the theoretical point of view, reconstruction problems belong to the class of ill-posed problems and should be considered using regularization. Regularization introduces an additional unknown regularization parameter into the reconstruction procedure as compared with non-regularized algorithms. However, a comparison of non-regularized OSEM and regularized MAP algorithms with fixed regularization parameters has shown very minor difference between reconstructions. This problem is analyzed in the present paper. To improve the reconstruction quality, a method of local regularization is proposed based on the spatially adaptive regularization parameter. The MAP algorithm with local regularization was tested in reconstruction of the Hoffman brain phantom.

  4. Comparison of Values in 5th, 6th, 7th and 8th Grade Primary Education Music Class Students'? Workbooks According to Rokeach?s and Akbas's Value Classifications

    ERIC Educational Resources Information Center

    Çakirer, H. Serdar

    2014-01-01

    The aim of the present study is to compare the values in the songs of 5th, 6th, 7th and 8th grade primary education music classes students? workbooks according to the value categorizations proposed by Rockeach and Akbas and which values among the categories mentioned are taught to the students in the 5th, 6th, 7th and 8th grade primary education…

  5. Comparison of Values in 5th, 6th, 7th and 8th Grade Primary Education Music Class Students'? Workbooks According to Rokeach?s and Akbas's Value Classifications

    ERIC Educational Resources Information Center

    Çakirer, H. Serdar

    2014-01-01

    The aim of the present study is to compare the values in the songs of 5th, 6th, 7th and 8th grade primary education music classes students? workbooks according to the value categorizations proposed by Rockeach and Akbas and which values among the categories mentioned are taught to the students in the 5th, 6th, 7th and 8th grade primary education…

  6. Computer integrated drug prevention: a new approach to teach lower socioeconomic 5th and 6th grade Israeli children to say no to drugs.

    PubMed

    Gropper, M; Liraz, Z; Portowicz, D; Schindler, M

    1995-01-01

    Drug prevention education provides an important first line of defense against future drug use. Many drug prevention strategies have been developed which teach youngsters of all ages how to say no to drugs. Nevertheless, the problem of drug use and abuse continues to escalate, and younger children, particularly those undergoing harsh psychosocial stress (e.g., hunger, lack of housing, broken homes, family unemployment, etc.), are increasingly becoming a population at-risk. In this paper, the authors describe an original drug prevention program that was developed in Israel aimed at teaching resiliency skills to 5th and 6th grade children growing up in a poverty stricken, urban community. The program, drawing on social learning theory, utilizes an attractive, cartoon illustrated, computer program combined with games, role-playing and group work techniques to prevent future drug use in preadolescent children.

  7. Islet cell research brings hope for a diabetes cure: meeting report from the 6(th) annual islet society meeting in Stellenbosch, South Africa.

    PubMed

    Tchokonte-Nana, V; Cockburn, I L; Manda, J K; Kotze, P C; Johnson, J D

    2014-01-01

    The International Diabetes Federation predicts that, over the next twenty years, the largest increase in the prevalence of diabetes will be in the Africa region. Recognizing an unmet need for more focus on Africa and engagement with African scholars, the Islet Society held its 6th annual meeting July 20-21, 2014 in Stellenbosch, South Africa. Here, we present a report that covers the presentations and discussion points from that meeting. Work was presented on a variety of topics and included presentations by a significant proportion of Africa diabetes researchers. Overall, it was an excellent conference, with many new international collaborations initiated. We hope that other groups will also respond to the need for more conferences in Africa and focused on Africa.

  8. Advances in the biology and therapy of chronic myeloid leukemia: proceedings from the 6th Post-ASH International Chronic Myeloid Leukemia and Myeloproliferative Neoplasms Workshop.

    PubMed

    Van Etten, Richard A; Mauro, Michael; Radich, Jerald P; Goldman, John M; Saglio, Giuseppe; Jamieson, Catriona; Soverini, Simona; Gambacorti-Passerini, Carlo; Hehlmann, Rüdiger; Martinelli, Giovanni; Perrotti, Danilo; Scadden, David T; Skorski, Tomasz; Tefferi, Ayalew; Mughal, Tariq I

    2013-06-01

    Following the 53rd annual meeting of the American Society of Hematology (ASH) in San Diego in December 2011, a group of clinical and laboratory investigators convened for the 6th Post-ASH International Workshop on Chronic Myeloid Leukemia (CML) and Myeloproliferative Neoplasms (MPN). The Workshop took place on 13-14 December at the Estancia, La Jolla, California, USA. This report summarizes the most recent advances in the biology and therapy of CML that were presented at the ASH meeting and discussed at the Workshop. Preclinical studies focused on the CML stem cell and its niche, and on early results of deep sequencing of CML genomes. Clinical advances include updates on second- and third-generation tyrosine kinase inhibitors (TKIs), molecular monitoring, TKI discontinuation studies and new therapeutic agents. A report summarizing the pertinent advances in MPN has been published separately.

  9. Climate Change and the Water Cycle: A New Southwest Regional Climate Hub Curriculum Unit for 6th-12th Grade Students

    NASA Astrophysics Data System (ADS)

    Elias, E.; Steele, C. M.; Bestelmeyer, S.; Haan-Amato, S.; Deswood, H.; Rango, A.; Havstad, K.

    2015-12-01

    As climate change intensifies, increased temperatures and altered precipitation will make water, a limited resource in the arid southwestern United States, even scarcer in many locations. The USDA Southwest Regional Climate Hub (SWRCH) developed Climate Change and the Water Cycle, an engaging and scientifically rigorous education unit for 6th -12th grade students. The unit is aligned with Common Core State Standards and Next Generation Science Standards. Nine activities can be conducted over 10 instruction hours. Each activity can also stand alone. In partnership with SWRCH, the Asombro Institute for Science Education developed the unit. Each activity was reviewed by an educator for educational practices and by a scientist for scientific accuracy. The unit was pilot tested with 524 students in 2014, and pre- and post-tests were administered. Ninety-one percent of students were able to name a greenhouse gas on the post-test, compared to only 48% on the pre-test. On the post-test, 86% of students identified the relationship between average global temperature and carbon dioxide levels in the atmosphere, compared to only 52% on the pre-test. A student commented: "I loved all of the activities! They are fun and help us understand about what goes on in the world." Educators who participated in pilot testing said: "the entire curriculum is great, but I was particularly impressed with the progression of ideas and the variety of lessons," and "students could see the relevance and importance of these real life issues." Anyone interested in using the unit to host workshops for teachers in southwestern states should contact Asombro for more information (information@asombro.org). The Climate Change and the Water Cycle 6th-12th grade curriculum unit is available online: www.swclimatehub.info/education/climate-change-and-water-cycle

  10. Mainstreaming the Regular Classroom Student.

    ERIC Educational Resources Information Center

    Kahn, Michael

    The paper presents activities, suggested by regular classroom teachers, to help prepare the regular classroom student for mainstreaming. The author points out that regular classroom children need a vehicle in which curiosity, concern, interest, fear, attitudes and feelings can be fully explored, where prejudices can be dispelled, and where the…

  11. Apparatus for inspecting piping

    DOEpatents

    Zollingger, W.T.; Appel, D.K.; Park, L.R.

    1995-03-21

    An inspection rabbit is described for inspecting piping systems having severe bends therein. The rabbit consists of a flexible, modular body containing a miniaturized eddy current inspection probe, a self-contained power supply for proper operation of the rabbit, an outer surface that allows ease of movement through piping systems and means for transmitting data generated by the inspection device. The body is preferably made of flexible polyvinyl chloride (PVC) tubing or, alternatively, silicone rubber with a shrink wrapping of polytetrafluoroethylene (TEFLON{trademark}). The body is formed to contain the power supply, preferably a plurality of batteries, and a spool of communication wire that connects to a data processing computer external to the piping system. 6 figures.

  12. Guidelines for software inspections

    NASA Technical Reports Server (NTRS)

    1983-01-01

    Quality control inspections are software problem finding procedures which provide defect removal as well as improvements in software functionality, maintenance, quality, and development and testing methodology is discussed. The many side benefits include education, documentation, training, and scheduling.

  13. Apparatus for inspecting piping

    DOEpatents

    Zollingger, W. Thor; Appel, D. Keith; Park, Larry R.

    1995-01-01

    An inspection rabbit for inspecting piping systems having severe bends therein. The rabbit consists of a flexible, modular body containing a miniaturized eddy current inspection probe, a self-contained power supply for proper operation of the rabbit, an outer surface that allows ease of movement through piping systems and means for transmitting data generated by the inspection device. The body is preferably made of flexible polyvinyl chloride (PVC) tubing or, alternatively, silicone rubber with a shrink wrapping of polytetrafluoroethylene (TEFLON.RTM.). The body is formed to contain the power supply, preferably a plurality of batteries, and a spool of communication wire that connects to a data processing computer external to the piping system.

  14. Remote surface inspection system

    NASA Technical Reports Server (NTRS)

    Hayati, S.; Balaram, J.; Seraji, H.; Kim, W. S.; Tso, K.; Prasad, V.

    1993-01-01

    This paper reports on an on-going research and development effort in remote surface inspection of space platforms such as the Space Station Freedom (SSF). It describes the space environment and identifies the types of damage for which to search. This paper provides an overview of the Remote Surface Inspection System that was developed to conduct proof-of-concept demonstrations and to perform experiments in a laboratory environment. Specifically, the paper describes three technology areas: (1) manipulator control for sensor placement; (2) automated non-contact inspection to detect and classify flaws; and (3) an operator interface to command the system interactively and receive raw or processed sensor data. Initial findings for the automated and human visual inspection tests are reported.

  15. Inspecting Juno Radiation Vault

    NASA Image and Video Library

    2010-07-12

    A technician inspects the special radiation vault being installed atop the propulsion module of NASA Juno spacecraft; the vault has titanium walls to protect the spacecraft electronic brain and heart from Jupiter harsh radiation environment.

  16. Information-Driven Inspections

    SciTech Connect

    Laughter, Mark D; Whitaker, J Michael; Lockwood, Dunbar

    2010-01-01

    New uranium enrichment capacity is being built worldwide in response to perceived shortfalls in future supply. To meet increasing safeguards responsibilities with limited resources, the nonproliferation community is exploring next-generation concepts to increase the effectiveness and efficiency of safeguards, such as advanced technologies to enable unattended monitoring of nuclear material. These include attribute measurement technologies, data authentication tools, and transmission and security methods. However, there are several conceptual issues with how such data would be used to improve the ability of a safeguards inspectorate such as the International Atomic Energy Agency (IAEA) to reach better safeguards conclusions regarding the activities of a State. The IAEA is pursuing the implementation of information-driven safeguards, whereby all available sources of information are used to make the application of safeguards more effective and efficient. Data from continuous, unattended monitoring systems can be used to optimize on-site inspection scheduling and activities at declared facilities, resulting in fewer, better inspections. Such information-driven inspections are the logical evolution of inspection planning - making use of all available information to enhance scheduled and randomized inspections. Data collection and analysis approaches for unattended monitoring systems can be designed to protect sensitive information while enabling information-driven inspections. A number of such inspections within a predetermined range could reduce inspection frequency while providing an equal or greater level of deterrence against illicit activity, all while meeting operator and technology holder requirements and reducing inspector and operator burden. Three options for using unattended monitoring data to determine an information-driven inspection schedule are to (1) send all unattended monitoring data off-site, which will require advances in data analysis techniques to

  17. Nuclear Plant Inspection

    NASA Technical Reports Server (NTRS)

    1983-01-01

    Engineers from the Power Authority of the State of New York use a Crack Growth Analysis Program supplied by COSMIC (Computer Software Management and Information Center) in one stage of nuclear plant inspection. Welds of the nuclear steam supply system are checked for cracks; radiographs, dye penetration and visual inspections are performed to locate cracks in the metal structure and welds. The software package includes three separate crack growth analysis models and enables necessary repairs to be planned before serious problems develop.

  18. Source Inspection Scheduling Calendar

    NASA Technical Reports Server (NTRS)

    Hollis, Brayden

    2011-01-01

    Quality is an essential component for creating flight hardware travelling through space since the hardware is extremely expensive and cannot be reworked or repaired once launched. An important step in this process is ensuring the quality of hardware procured from Jet Propulsion Laboratory's (JPL) suppliers. An important element of determining supplier quality is source inspection. Source inspections are performed at suppliers' facilities by JPL employeesto ensure that hardware characteristics are acceptable before being covered up and/or delivered to JPL.

  19. Wedges for ultrasonic inspection

    DOEpatents

    Gavin, Donald A.

    1982-01-01

    An ultrasonic transducer device is provided which is used in ultrasonic inspection of the material surrounding a threaded hole and which comprises a wedge of plastic or the like including a curved threaded surface adapted to be screwed into the threaded hole and a generally planar surface on which a conventional ultrasonic transducer is mounted. The plastic wedge can be rotated within the threaded hole to inspect for flaws in the material surrounding the threaded hole.

  20. Inspection Manual for Metals

    DTIC Science & Technology

    1940-05-01

    make a complete list of all equipment needed for the inspection. It is highly important that inspection equipment be available for use prior to the time...no standards covering the various degrees of surface finish. It is necessary, therefore, for the inspector to consider the ser- vice use of the part...sometimes used . To stop the etching action, the beaker or dish and its contents are placed directly under a cold water tap and the v.ater allowed to run

  1. Surface inspection operator interface

    NASA Astrophysics Data System (ADS)

    Creek, Russell C.

    1992-03-01

    Surface inspection systems are widely used in many industries including steel, tin, aluminum, and paper. These systems generally use machine vision technology to detect defective surface regions and can generate very high data output rates which can be difficult for line operators to absorb and use. A graphical, windowing interface is described which provides the operators with an overview of the surface quality of the inspected web while still allowing them to select individual defective regions for display. A touch screen is used as the only operator input. This required alterations to some screen widgets due to subtle ergonomic differences of touch screen input over mouse input. The interface, although developed for inspecting coated steel, has been designed to be adaptable to other surface inspection applications. Facility is provided to allow the detection, classification, and display functions of the inspection system to be readily changed. Modifications can be implemented on two main levels; changes that reflect the configuration of the hardware system and control the detection and classification components of the surface inspection system are accessible only to authorized staff while those affecting the display and alarm settings of defect types may be changed by operators and this can generally be done dynamically.

  2. 49 CFR 1248.6 - Public inspection-railroad reports.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... STATISTICS § 1248.6 Public inspection—railroad reports. The individual commodity statistics reports of class... public inspection, and such required commodity statistics reports, to be filed for the years beginning..., may be excluded from a railroad's regular freight commodity statistics report and filed in...

  3. 46 CFR 160.043-5 - Inspections and tests.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Inspections and tests. (a) General. Jackknives are not ordinarily subjected to regularly scheduled factory... place of manufacture. (b) Hardness test. Hardness of the blade, can opener, and spring metal shall be... blade of the knife except the tang clamped in vertical jaws so that the handle is in a...

  4. 46 CFR 160.043-5 - Inspections and tests.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Inspections and tests. (a) General. Jackknives are not ordinarily subjected to regularly scheduled factory... place of manufacture. (b) Hardness test. Hardness of the blade, can opener, and spring metal shall be... blade of the knife except the tang clamped in vertical jaws so that the handle is in a...

  5. 23 CFR 650.313 - Inspection procedures.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... location of underwater elements and include a description of the underwater elements, the inspection.... Inspect those elements requiring underwater inspections according to these procedures. (3) Bridges that... periodic field review of inspection teams, periodic bridge inspection refresher training for program...

  6. National Program for Inspection of Non-Federal Dams. Glendale Dam (MA 00021), Housatonic River Basin, Stockbridge, Massachusetts. Phase I Inspection Report.

    DTIC Science & Technology

    1979-07-01

    lma ? 10100Ir Weakh ""maw) DAMS, INSPECTION, DAM SAFETY, Housatonic River Basin Stockbridge, MassachusettsL ENSTRACT (Coniftwean - evffea 40,14 Of...sloping, high banks overgrown with trees and bushes. Flows * I in gently meandering path to the Village of Housatonic 6 th J.e Regulating Outlets. There...Reservoir Area. There is an island in the river upstream of the dam with a grove of mature trees established on it, Photo No. 11. An unpaved access road

  7. Ensemble manifold regularization.

    PubMed

    Geng, Bo; Tao, Dacheng; Xu, Chao; Yang, Linjun; Hua, Xian-Sheng

    2012-06-01

    We propose an automatic approximation of the intrinsic manifold for general semi-supervised learning (SSL) problems. Unfortunately, it is not trivial to define an optimization function to obtain optimal hyperparameters. Usually, cross validation is applied, but it does not necessarily scale up. Other problems derive from the suboptimality incurred by discrete grid search and the overfitting. Therefore, we develop an ensemble manifold regularization (EMR) framework to approximate the intrinsic manifold by combining several initial guesses. Algorithmically, we designed EMR carefully so it 1) learns both the composite manifold and the semi-supervised learner jointly, 2) is fully automatic for learning the intrinsic manifold hyperparameters implicitly, 3) is conditionally optimal for intrinsic manifold approximation under a mild and reasonable assumption, and 4) is scalable for a large number of candidate manifold hyperparameters, from both time and space perspectives. Furthermore, we prove the convergence property of EMR to the deterministic matrix at rate root-n. Extensive experiments over both synthetic and real data sets demonstrate the effectiveness of the proposed framework.

  8. 5/6th nephrectomy in combination with high salt diet and nitric oxide synthase inhibition to induce chronic kidney disease in the Lewis rat.

    PubMed

    van Koppen, Arianne; Verhaar, Marianne C; Bongartz, Lennart G; Joles, Jaap A

    2013-07-03

    Chronic kidney disease (CKD) is a global problem. Slowing CKD progression is a major health priority. Since CKD is characterized by complex derangements of homeostasis, integrative animal models are necessary to study development and progression of CKD. To study development of CKD and novel therapeutic interventions in CKD, we use the 5/6th nephrectomy ablation model, a well known experimental model of progressive renal disease, resembling several aspects of human CKD. The gross reduction in renal mass causes progressive glomerular and tubulo-interstitial injury, loss of remnant nephrons and development of systemic and glomerular hypertension. It is also associated with progressive intrarenal capillary loss, inflammation and glomerulosclerosis. Risk factors for CKD invariably impact on endothelial function. To mimic this, we combine removal of 5/6th of renal mass with nitric oxide (NO) depletion and a high salt diet. After arrival and acclimatization, animals receive a NO synthase inhibitor (NG-nitro-L-Arginine) (L-NNA) supplemented to drinking water (20 mg/L) for a period of 4 weeks, followed by right sided uninephrectomy. One week later, a subtotal nephrectomy (SNX) is performed on the left side. After SNX, animals are allowed to recover for two days followed by LNNA in drinking water (20 mg/L) for a further period of 4 weeks. A high salt diet (6%), supplemented in ground chow (see time line Figure 1), is continued throughout the experiment. Progression of renal failure is followed over time by measuring plasma urea, systolic blood pressure and proteinuria. By six weeks after SNX, renal failure has developed. Renal function is measured using 'gold standard' inulin and para-amino hippuric acid (PAH) clearance technology. This model of CKD is characterized by a reduction in glomerular filtration rate (GFR) and effective renal plasma flow (ERPF), hypertension (systolic blood pressure>150 mmHg), proteinuria (> 50 mg/24 hr) and mild uremia (>10 mM). Histological

  9. Impact on smoking behaviour of the New Zealand annual increase in tobacco tax: Data for the 5th and 6th year of increases.

    PubMed

    Li, Judy; Newcombe, Rhiannon; Guiney, Hayley; Walton, Darren

    2016-09-13

    New Zealand has implemented a series of seven annual increases in tobacco tax since 2010. All tax increases, except for the first in the series, were pre-announced. It is unusual for governments to introduce small, persistent, and predictable increases in tobacco tax, and little is known about the impact of such a strategy. This paper evaluates the impact of the 5(th) and 6(th) annual increases. Smokers' behaviours were self-reported during the three-month period before, and the three-month period after, the two annual increases. Responses to the two increases were analysed separately, and GEE models were used to control for socio-demographic variables, recent quit attempts, and the research design. Findings were consistent across years. The proportion of participants who made a smoking-related (54-56% before and after each tax increase) or product-related change (5(th) tax increase: 17-19%; 6(th) tax increase: 21-22%) did not significantly alter from before to after each tax increase. However, it should be noted that the proportion of participants making smoking-related changes was generally high, even prior to each increase. For example, before the 2015 tax increase, 1% reported quitting completely, 21% trying to quit, and 53% cutting down. In New Zealand, with its series of annual tobacco tax increases since 2010, there were no significant changes in smoking- or product- related behaviour associated with the fifth and sixth increases. Nevertheless, overall cessation-related activity was high, with a majority of participants reporting either quitting and/or cutting-down recently. Little is known about the impact of small, persistent, predictable tobacco tax increases on smoking behaviour. This study evaluated the impact of the fifth (in 2014) and sixth (2015) tax increases in an annual series implemented in New Zealand. Although there were no detectable changes in smoking behaviours from before to after each tax increase, self-reported cessation-related activity

  10. Evidence of strong Quaternary earthquakes in the epicentral areaof the April 6th 2009 L'Aquila seismic event from sediment paleofluidization and overconsolidation

    NASA Astrophysics Data System (ADS)

    Storti, F.; Balsamo, F.; Aldega, L.; Corrado, S.; Di Paolo, L.; Mastalertz, M.; Tallini, M.

    2012-04-01

    The strong seismological potential of the Central Apennines, including the L'Aquila basin, is documented in the historical heritage of the past two millenia and by paleoseismological data. Despite the main active fault system network of Central Italy is well described and mapped, the April 6th 2009 L'Aquila event showed that Mw> 6.0 earthquakes can occur on fault zones characterized by subtlemorphotectonic evidence, like the Paganica Fault, whose seismic hazard potential may thus be overlooked. An additional source of uncertainty is provided by the evidence that in the L'Aquila region many active extensional fault systems developed by negative inversion of pre-existing contractional deformation structures. The resulting complex along-strike segmentation and overlap patterns are thus governed by the interplay between the modern extensional stress field and the structural inheritance and reduce the effectiveness of predictive scaling laws, which do not typically account for fault attributes produced by polyphased tectonics. This is particularly true in the L'Aquila region, where seismic activation of the northwestern half of the basin-boundary fault system has been proposed for the 1703 Mw ~ 7.0 earthquake, whereas only the central segment was activated in 1461 and 2009, producing earthquakes with Mw ~ 6.0 - 6.3. The reasons for this dual behaviour are still unclear despite many structural and paleoseismological studies. Indirect evidence for paleoearthquake magnitude from ground shaking effects, like paleo-fluidization structures, can provide very useful complementary information on maximum expected earthquake intensities along active fault systems.In this work wedescribe in detail large paleo-fluidization-induced features associated with a previously unmapped extensional fault zone cutting through Quaternary strata. These sediments, including lacustrine lignites and mudstones, show a somehow enigmatic overconsolidation that we quantitatively describe, as well as

  11. Piping inspection round robin

    SciTech Connect

    Heasler, P.G.; Doctor, S.R.

    1996-04-01

    The piping inspection round robin was conducted in 1981 at the Pacific Northwest National Laboratory (PNNL) to quantify the capability of ultrasonics for inservice inspection and to address some aspects of reliability for this type of nondestructive evaluation (NDE). The round robin measured the crack detection capabilities of seven field inspection teams who employed procedures that met or exceeded the 1977 edition through the 1978 addenda of the American Society of Mechanical Engineers (ASME) Section 11 Code requirements. Three different types of materials were employed in the study (cast stainless steel, clad ferritic, and wrought stainless steel), and two different types of flaws were implanted into the specimens (intergranular stress corrosion cracks (IGSCCs) and thermal fatigue cracks (TFCs)). When considering near-side inspection, far-side inspection, and false call rate, the overall performance was found to be best in clad ferritic, less effective in wrought stainless steel and the worst in cast stainless steel. Depth sizing performance showed little correlation with the true crack depths.

  12. Meeting Report: "Proteomics from Discovery to Function:" 6th Annual Meeting of Proteomics Society, India and International Conference-A Milestone for the Indian Proteomics Community.

    PubMed

    Gupta, Shabarni; Reddy, Panga Jaipal; Ray, Sandipan; Atak, Apurva; Gollapalli, Kishore; Jain, Rekha; Shah, Veenita Grover; Ghantasala, Saicharan; Kumar, Saurabh; Pandala, Narendra Goud; Phapale, Prasad; Pandey, Vishnu Kumar; Zingde, Surekha; Srivastava, Sanjeeva

    2015-06-01

    Proteomics is at the epicenter of post-genomics biotechnologies that are currently driving the next generation system science. Moreover, proteomics is a truly global science. The 6(th) Annual Meeting of Proteomics Society, India (PSI) and International Conference on "Proteomics from Discovery to Function" held from December 7-9, 2014, was a transformative endeavor for global proteomics, bringing together the luminaries in the field of proteomics for the very first time in India. This meeting report presents the lessons learned and the highlights of this international scientific conference that was comprised of nine thematic sessions, pre- and post-conference workshops, and an opportunity to cultivate enduring collaborations for proteomics science to benefit both India and global society. The conference had an unforgettable impression on the participants: for the first time, India hosted past and present President and Council members from the Human Proteome Organization (HUPO), along with eminent scientists and young scholars from India and abroad in the field of proteomics at such a large scale, a major highlight of this international event. In all, the PSI 2014 was a milestone conference that has firmly poised the Indian life sciences community as a leading contributor to post-genomics life sciences, thus cultivating crucial trans-generational capacity and inspiration by recognizing the emerging scholars and omics systems scientists who can think and conduct science from cell to society.

  13. Hematology oncology practice in the Asia-Pacific APHCON survey results from the 6th international hematologic malignancies conference: bridging the gap 2015, Beijing, China.

    PubMed

    Huang, Xiao Jun; Liu, Kaiyan; Ritchie, David; Andersson, Borje; Lu, Jin; Hou, Jian; Burguera, Adolfo de la Fuente; Wang, JianXiang; Yeoh, Allen; Yan, Chenhua; Zhou, Daobin; Tan, Daryl; Kim, Dong Wook; Wu, Depei; Shpall, Elizabeth; Kornblau, Stephen; Neelapu, Sattava; Hongeng, Suradej; Li, Jianyong; Hu, Jiong; Zhang, Lian Sheng; Wang, Michael; Malhotra, Pankaj; Jiang, Qian; Qin, Yazhen; Wong, Raymond; Champlin, Richard; Hagemeister, Frederick; Westin, Jason; Iyer, Swaminathan; Mathews, Vikram; Wang, Yu; Hu, Yu; Xiao, Zhijian; Shao, Zonghong; Orlowski, Robert Z; Chim, Chor Sang; Mulligan, Stephen; Sanz, Miguel; Ozawa, Keiya; Parmar, Simrit; Issaragrisil, Surapol

    2017-06-20

    This report serves as a snapshot of the state-of-knowledge in the Asia Pacific (APAC) Hematology Oncology community, and establishes a baseline for longitudinal investigations to follow changes in best practices over time. The objective of this study was to understand the approach to hematologic diseases, common standards of care and best practices, issues that remain controversial or debated, and educational or resource gaps that warrant attention. We used mobile application to disseminate and distribute questionnaires to delegates during the 6th international hematologic malignancies conference hosted by the APAC Hematology Consortium at Beijing, China. User responses were collected in an anonymous fashion. We report survey results in two ways: the overall responses, and responses as stratified between Chinese physicians and "Other" represented nationalities. Overall geographical concordance in survey responses was positive and strong. Perhaps more interesting than instances of absolute agreement, these data provide a unique opportunity to identify topics in which physician knowledge or opinions diverge. We assigned questions from all modules to broad categories of: patient information; diagnosis; treatment preference; transplantation; and general knowledge/opinion. On average, we observed a geographic difference of 15% for any particular answer choice, and this was fairly constant across survey modules. These results reveal utility and need for widespread and ongoing initiatives to assess knowledge and provide evidence-based education in real time. The data will be made more valuable by longitudinal participation, such that we can monitor changes in the state of the art over time.

  14. Vegetation dieback as a proxy for temperature within a wet pyroclastic density current: A novel experiment and observations from the 6th of August 2012 Tongariro eruption

    NASA Astrophysics Data System (ADS)

    Efford, Jackson T.; Bylsma, Rebecca J.; Clarkson, Bruce D.; Pittari, Adrian; Mauriohooho, Kate; Moon, Vicki G.

    2014-10-01

    The 6th of August 2012 eruption of Te Maari (Mt Tongariro, New Zealand) generated wet pyroclastic density currents (PDCs) which caused widespread dieback of vegetation (singed, brown foliage) in their path. An absence of significant charcoal formation suggests that PDC temperatures were mostly below 250 °C. Textural evidence for liquid water being present in the matrices during emplacement (vesicles) suggests that temperatures were < 100 °C. We determined a probable minimum PDC temperature using an experiment replicating the critical temperatures required to induce foliar browning in seven species affected by the eruption. In locations where all species exhibited browned foliage (or were defoliated), temperatures were probably ≥ 64 °C assuming a PDC duration of 60 s. In the more distal areas, where only the most susceptible species were browned while others remained healthy and unaffected, temperatures were probably around 51-58 °C. These results have relevance to volcanic hazard mitigation and risk assessment, especially on the popular Tongariro Alpine Crossing.

  15. The beginning of metallurgy in the southern Levant: a late 6th millennium CalBC copper awl from Tel Tsaf, Israel.

    PubMed

    Garfinkel, Yosef; Klimscha, Florian; Shalev, Sariel; Rosenberg, Danny

    2014-01-01

    The beginning of metallurgy in the ancient Near East attracts much attention. The southern Levant, with the rich assemblage of copper artifacts from the Nahal Mishmar cave and the unique gold rings of the Nahal Qanah cave, is regarded as a main center of early metallurgy during the second half of the 5th millennium CalBC. However, a recently discovered copper awl from a Middle Chalcolithic burial at Tel Tsaf, Jordan Valley, Israel, suggests that cast metal technology was introduced to the region as early as the late 6th millennium CalBC. This paper examines the chemical composition of this item and reviews its context. The results indicate that it was exported from a distant source, probably in the Caucasus, and that the location where it was found is indicative of the social status of the buried individual. This rare finding indicates that metallurgy was first diffused [corrected] to the southern Levant through exchange networks and only centuries later involved local productionThis copper awl, the earliest metal artifact found in the southern Levant, indicates that the elaborate Late Chalcolithic metallurgy developed from a more ancient tradition.

  16. Modeling of local 3D effects of the April 6th 2009 l’Aquila (Italy) event in the City of Rome

    NASA Astrophysics Data System (ADS)

    Caserta, A.; Oprsal, I.; Rovelli, A.; Marra, F.; Govoni, A.; Vinci, S.

    2009-12-01

    Several events of the seismic sequence started on 6th of April 2009, that struck the town of l'Aquila, Italy, have been recorded by an array of seismic stations, located approximately 90 km south-west of the epicenters. One of the stations is in a 80-m-deep borehole, installed since the early 2008 in the middle of the main sedimentary body of the city: the Tiber valley. This represents a unique opportunity to tune seismic simulations of the soil shaking due to a seismic sequence located in Central Apennines region. This latter is considered, with the Albani Hills one, the main seismogenic area responsible of the seismic hazard in the city. We have generated a 3D velocity model for a portion of the city (5 EW x 3 NS km2 wide, and 200 m deep, including topography) where the array is located. A viscoelastic wave propagation due to S-wave pulse of general polarization and given incidence is obtained by the 3D FD hybrid numerical modeling. The 3D pulse response and the borehole recording are then used to generate the complete 3D synthetics covering the area. The results are verified by comparing to the surface recordings and large ground motion amplifications data.

  17. The Hetu'u Global Network: Using the rare June 5th/6th Transit of Venus to Bring Astronomy to the Remote Easter Island

    NASA Astrophysics Data System (ADS)

    Faherty, Jacqueline; Rodriguez, D.

    2013-01-01

    There are rare times in astronomy when a celestial event, visible in broad daylight, can be used to measure a fundamental parameter and inspire a globe full of school age students. The June 5th/6th transit of Venus was one such event. In celebration, nine astronomy postdocs from the Chilean mainland traveled to Easter Island to lead a series of astronomy outreach activities over three days, culminating in a transit-viewing event. Our team dubbed "Equipo Hetu'u" or "Team Star" in the Rapa Nui (Easter Island native) language spent two days giving astronomy talks and doing hands-on demonstrations at the Museo Antropologico P. Sebastian Englert. In the final day-and-a-half leading up to the transit, we visited the science classes in the majority of the schools on the island, in order to spread the message about the once-in-a-lifetime transit event, highlighting how we planned on using it to measure the distance to the Sun. We estimate over 25% 1500 people) of this remote island participated in one or more of our organized activities. Our experience with this project is an excellent lesson on how to organize, lead, and fully execute a major outreach endeavor that inspires hundreds with minimal resources (save the spectacular event provided by the cosmos).

  18. The Beginning of Metallurgy in the Southern Levant: A Late 6th Millennium CalBC Copper Awl from Tel Tsaf, Israel

    PubMed Central

    Garfinkel, Yosef; Klimscha, Florian; Shalev, Sariel; Rosenberg, Danny

    2014-01-01

    The beginning of metallurgy in the ancient Near East attracts much attention. The southern Levant, with the rich assemblage of copper artifacts from the Nahal Mishmar cave and the unique gold rings of the Nahal Qanah cave, is regarded as a main center of early metallurgy during the second half of the 5th millennium CalBC. However, a recently discovered copper awl from a Middle Chalcolithic burial at Tel Tsaf, Jordan Valley, Israel, suggests that cast metal technology was introduced to the region as early as the late 6th millennium CalBC. This paper examines the chemical composition of this item and reviews its context. The results indicate that it was exported from a distant source, probably in the Caucasus, and that the location where it was found is indicative of the social status of the buried individual. This rare finding indicates that metallurgy was first defused to the southern Levant through exchange networks and only centuries later involved local production. This copper awl, the earliest metal artifact found in the southern Levant, indicates that the elaborate Late Chalcolithic metallurgy developed from a more ancient tradition. PMID:24671185

  19. Hematology oncology practice in the Asia-Pacific APHCON survey results from the 6th international hematologic malignancies conference: bridging the gap 2015, Beijing, China

    PubMed Central

    Huang, Xiao Jun; Liu, Kaiyan; Ritchie, David; Andersson, Borje; Lu, Jin; Hou, Jian; Burguera, Adolfo de Fuente; Wang, JianXiang; Yeoh, Allen; Yan, Chenhua; Zhou, Daobin; Tan, Daryl; Kim, Dong Wook; Wu, Depei; Shpall, Elizabeth; Kornblau, Stephen; Neelapu, Sattava; Hongeng, Suradej; Li, Jianyong; Hu, Jiong; Zhang, Lian Sheng; Wang, Michael; Malhotra, Pankaj; Jiang, Qian; Qin, Yazhen; Wong, Raymond; Champlin, Richard; Hagemeister, Frederick; Westin, Jason; Iyer, Swaminathan; Mathews, Vikram; Wang, Yu; Hu, Yu; Xiao, Zhijian; Shao, Zonghong; Orlowski, Robert Z.; Chim, Chor Sang; Mulligan, Stephen; Sanz, Miguel; Ozawa, Keiya; Parmar, Simrit; Issaragrisil, Surapol

    2017-01-01

    This report serves as a snapshot of the state-of-knowledge in the Asia Pacific (APAC) Hematology Oncology community, and establishes a baseline for longitudinal investigations to follow changes in best practices over time. The objective of this study was to understand the approach to hematologic diseases, common standards of care and best practices, issues that remain controversial or debated, and educational or resource gaps that warrant attention. We used mobile application to disseminate and distribute questionnaires to delegates during the 6th international hematologic malignancies conference hosted by the APAC Hematology Consortium at Beijing, China. User responses were collected in an anonymous fashion. We report survey results in two ways: the overall responses, and responses as stratified between Chinese physicians and “Other” represented nationalities. Overall geographical concordance in survey responses was positive and strong. Perhaps more interesting than instances of absolute agreement, these data provide a unique opportunity to identify topics in which physician knowledge or opinions diverge. We assigned questions from all modules to broad categories of: patient information; diagnosis; treatment preference; transplantation; and general knowledge/opinion. On average, we observed a geographic difference of 15% for any particular answer choice, and this was fairly constant across survey modules. These results reveal utility and need for widespread and ongoing initiatives to assess knowledge and provide evidence-based education in real time. The data will be made more valuable by longitudinal participation, such that we can monitor changes in the state of the art over time. PMID:28404929

  20. Partnering to change the world for people with haemophilia: 6(th) Haemophilia Global Summit, Prague, Czech Republic, 24-26(th) September 2015.

    PubMed

    Astermark, Jan; Hart, Dan; Lobet, Sébastien; Blatný, Jan; d'Oiron, Roseline; Kenet, Gili; Dolan, Gerry; Libotte, Valérie; Hermans, Cedric

    2016-07-01

    The 6(th) Haemophilia Global Summit was held in Prague, Czech Republic, in September 2015. The programme was designed by an independent Scientific Steering Committee of haemophilia experts and aimed to share optimal management strategies for haemophilia at all life stages, explore recent potential advances in the management of haemophilia A and B and discuss challenges in haemophilia care. In this supplement from the meeting, Dan Hart reviews the lessons that can be learnt from cost-constrained environments with regard to improving care for people with haemophilia globally. Sébastien Lobet discusses the importance of physical activity for optimising care and Roseline d'Oiron and Jan Blatný consider the role of real-world data in understanding the effect of treatment in a clinical setting over the long term and the true impact of treatment on the day-to-day life of the patient. Gili Kenet addresses the current challenges relating to the optimal management of prophylaxis, and Gerry Dolan and Cedric Hermans discuss the value of pharmacokinetic (PK) parameters in informing treatment decisions. Cedric Hermans and Valérie Libotte explore the importance of considering social and occupational development factors as an integral part of haemophilia care, and Jan Astermark reviews key strategies to predict and prevent inhibitor development.

  1. Advances in inspection automation

    NASA Astrophysics Data System (ADS)

    Weber, Walter H.; Mair, H. Douglas; Jansen, Dion; Lombardi, Luciano

    2013-01-01

    This new session at QNDE reflects the growing interest in inspection automation. Our paper describes a newly developed platform that makes the complex NDE automation possible without the need for software programmers. Inspection tasks that are tedious, error-prone or impossible for humans to perform can now be automated using a form of drag and drop visual scripting. Our work attempts to rectify the problem that NDE is not keeping pace with the rest of factory automation. Outside of NDE, robots routinely and autonomously machine parts, assemble components, weld structures and report progress to corporate databases. By contrast, components arriving in the NDT department typically require manual part handling, calibrations and analysis. The automation examples in this paper cover the development of robotic thickness gauging and the use of adaptive contour following on the NRU reactor inspection at Chalk River.

  2. Microstructure inspection endoscope design

    NASA Astrophysics Data System (ADS)

    Liu, Na; Jing, Chao; Zhang, Hongxia; Zhang, Yimo; Jing, Wencai; Zhou, Ge

    2005-02-01

    A microstructure inspection endoscope, based on directly imaging, is proposed. It is designed for detecting defects on the surface of optical fiber end. It is matched with FC or SC female fiber connector. The inspection head of the endoscope can be put into a 2.5-millimeter-diameter micro-pore. Its numerical aperture is not restricted by tiny dimension of object lenses. System resolution is increased to 600 line-pairs per millimeter. The endoscope consists of object lenses, scanner slab and kohler illumination system. The design provides possibility of various utilities such as aiming at a smaller subject by micro optical scanner and modeling the surface by tri-dimensional vision. And the optical system includes low-magnification lenses and high-magnification zoom lenses. Rough observation at low-magnification and particularly inspection at high-magnification are provided. The instrument has the advantages of high identification, compact configuration and flexible manipulation.

  3. On regular rotating black holes

    NASA Astrophysics Data System (ADS)

    Torres, R.; Fayos, F.

    2017-01-01

    Different proposals for regular rotating black hole spacetimes have appeared recently in the literature. However, a rigorous analysis and proof of the regularity of this kind of spacetimes is still lacking. In this note we analyze rotating Kerr-like black hole spacetimes and find the necessary and sufficient conditions for the regularity of all their second order scalar invariants polynomial in the Riemann tensor. We also show that the regularity is linked to a violation of the weak energy conditions around the core of the rotating black hole.

  4. Regular polygons in taxicab geometry

    NASA Astrophysics Data System (ADS)

    Hanson, J. R.

    2014-10-01

    A polygon of n sides will be called regular in taxicab geometry if it has n equal angles and n sides of equal taxicab length. This paper will show that there are no regular taxicab triangles and no regular taxicab pentagons. The sets of taxicab rectangles and taxicab squares will be shown to be the same, respectively, as the sets of Euclidean rectangles and Euclidean squares. A method of construction for a regular taxicab 2n-gon for any n will be demonstrated.

  5. Linear regularity and [phi]-regularity of nonconvex sets

    NASA Astrophysics Data System (ADS)

    Ng, Kung Fu; Zang, Rui

    2007-04-01

    In this paper, we discuss some sufficient conditions for the linear regularity and bounded linear regularity (and their variations) of finitely many closed (not necessarily convex) sets in a normed vector space. The accompanying necessary conditions are also given in the setting of Asplund spaces.

  6. Computer vision barrel inspection

    NASA Astrophysics Data System (ADS)

    Wolfe, William J.; Gunderson, James; Walworth, Matthew E.

    1994-02-01

    One of the Department of Energy's (DOE) ongoing tasks is the storage and inspection of a large number of waste barrels containing a variety of hazardous substances. Martin Marietta is currently contracted to develop a robotic system -- the Intelligent Mobile Sensor System (IMSS) -- for the automatic monitoring and inspection of these barrels. The IMSS is a mobile robot with multiple sensors: video cameras, illuminators, laser ranging and barcode reader. We assisted Martin Marietta in this task, specifically in the development of image processing algorithms that recognize and classify the barrel labels. Our subsystem uses video images to detect and locate the barcode, so that the barcode reader can be pointed at the barcode.

  7. Lighted, Folding Inspection Mirror

    NASA Technical Reports Server (NTRS)

    Roepe, Brian E.

    1991-01-01

    Compact, inexpensive tool used in place of expensive borescopes. Shortens inspection/photographing process. Includes two small metal or glass mirrors hinged together. Two 3-V light bulbs attached along edges of one mirror and connected to battery of two cells. Inserted into narrow opening of clevis or tand, and surface viewed and photographed in opposite mirror. Useful in assembly of segments of solid rocket motors as well as in postflight assessment, engineering evaluation, and refurbishment. Also applied in general to inspection and photographing of inner sealing surfaces to which access difficult.

  8. IR Spot Weld Inspect

    SciTech Connect

    Chen, Jian; Feng, Zhili

    2014-01-01

    In automotive industry, destructive inspection of spot welds is still the mandatory quality assurance method due to the lack of efficient non-destructive evaluation (NDE) tools. However, it is costly and time-consuming. Recently at ORNL, a new NDE prototype system for spot weld inspection using infrared (IR) thermography has been developed to address this problem. This software contains all the key functions that ensure the NDE system to work properly: system input/output control, image acquisition, data analysis, weld quality database generation and weld quality prediction, etc.

  9. Regularized Generalized Canonical Correlation Analysis

    ERIC Educational Resources Information Center

    Tenenhaus, Arthur; Tenenhaus, Michel

    2011-01-01

    Regularized generalized canonical correlation analysis (RGCCA) is a generalization of regularized canonical correlation analysis to three or more sets of variables. It constitutes a general framework for many multi-block data analysis methods. It combines the power of multi-block data analysis methods (maximization of well identified criteria) and…

  10. 76 FR 3629 - Regular Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-20

    ... From the Federal Register Online via the Government Publishing Office FARM CREDIT SYSTEM INSURANCE CORPORATION Farm Credit System Insurance Corporation Board Regular Meeting SUMMARY: Notice is hereby given of the regular meeting of the Farm Credit System Insurance Corporation Board (Board). Date and Time: The...

  11. Trajectory optimization using regularized variables

    NASA Technical Reports Server (NTRS)

    Lewallen, J. M.; Szebehely, V.; Tapley, B. D.

    1969-01-01

    Regularized equations for a particular optimal trajectory are compared with unregularized equations with respect to computational characteristics, using perturbation type numerical optimization. In the case of the three dimensional, low thrust, Earth-Jupiter rendezvous, the regularized equations yield a significant reduction in computer time.

  12. 75 FR 76006 - Regular Meeting

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-07

    ... Board (Board). Date and Time: The meeting of the Board will be held at the offices of the Farm Credit Administration in McLean, Virginia, on December 9, 2010, from 12:30 p.m. until such time as the Board concludes... CORPORATION Regular Meeting AGENCY: Farm Credit System Insurance Corporation Board. ACTION: Regular meeting...

  13. Regularly timed events amid chaos

    NASA Astrophysics Data System (ADS)

    Blakely, Jonathan N.; Cooper, Roy M.; Corron, Ned J.

    2015-11-01

    We show rigorously that the solutions of a class of chaotic oscillators are characterized by regularly timed events in which the derivative of the solution is instantaneously zero. The perfect regularity of these events is in stark contrast with the well-known unpredictability of chaos. We explore some consequences of these regularly timed events through experiments using chaotic electronic circuits. First, we show that a feedback loop can be implemented to phase lock the regularly timed events to a periodic external signal. In this arrangement the external signal regulates the timing of the chaotic signal but does not strictly lock its phase. That is, phase slips of the chaotic oscillation persist without disturbing timing of the regular events. Second, we couple the regularly timed events of one chaotic oscillator to those of another. A state of synchronization is observed where the oscillators exhibit synchronized regular events while their chaotic amplitudes and phases evolve independently. Finally, we add additional coupling to synchronize the amplitudes, as well, however in the opposite direction illustrating the independence of the amplitudes from the regularly timed events.

  14. Quantum Ergodicity on Regular Graphs

    NASA Astrophysics Data System (ADS)

    Anantharaman, Nalini

    2017-07-01

    We give three different proofs of the main result of Anantharaman and Le Masson (Duke Math J 164(4):723-765, 2015), establishing quantum ergodicity—a form of delocalization—for eigenfunctions of the laplacian on large regular graphs of fixed degree. These three proofs are much shorter than the original one, quite different from one another, and we feel that each of the four proofs sheds a different light on the problem. The goal of this exploration is to find a proof that could be adapted for other models of interest in mathematical physics, such as the Anderson model on large regular graphs, regular graphs with weighted edges, or possibly certain models of non-regular graphs. A source of optimism in this direction is that we are able to extend the last proof to the case of anisotropic random walks on large regular graphs.

  15. Remote Inspection Challenge

    ERIC Educational Resources Information Center

    Roman, Harry T.

    2013-01-01

    The ability to remotely inspect equipment of an aging infrastructure is becoming of major interest to many industries. Often the ability to just get a look at a piece of critical equipment can yield very important information. With millions of miles of piping installed throughout the United States, this vast network is critical to oil, natural…

  16. Automatic Inspection During Machining

    NASA Technical Reports Server (NTRS)

    Ransom, Clyde L.

    1988-01-01

    In experimental manufacturing process, numerically-controlled machine tool temporarily converts into inspection machine by installing electronic touch probes and specially-developed numerical-control software. Software drives probes in paths to and on newly machined parts and collects data on dimensions of parts.

  17. Innovative Inspection Techniques

    DTIC Science & Technology

    1993-01-01

    Typical Headlamps ...................................... 23 Table 5 Typical Personal Flashlights ................................ 24 Table 6 Characteristics...increasingly large volume of constantly changing regulatory and reference materials are among the examples of administrative workload which inspectors referred...and reference materials would provide more benefits than the use of advanced NDT technology in inspections. As a general rule, inspectors felt that

  18. Intelligent inspection system

    NASA Astrophysics Data System (ADS)

    May, Jeniece; Dale, Ken; Holloway, Mike; Gaby, Willard

    1997-01-01

    The intelligent inspection system is an advanced controller and analysis system for dimensional measuring machines dedicated to measuring surface of revolution mechanical parts. IIS was developed by the Lockheed Martin Energy Systems, Inc. Oak Ridge Y-12 plant because no commercial product was available to replace the obsolete computing systems on these important machines.

  19. Pre-Demolition Inspections

    EPA Pesticide Factsheets

    A pre-demolition inspection may be one of the most helpful and cost-efficient steps you can take to identify materials that should (or must) be removed from buildings prior to demolition. In some cases it may be required by regulation.

  20. Inspecting Playgrounds for Hazards.

    ERIC Educational Resources Information Center

    Gold, Seymour M.

    1991-01-01

    Safe playgrounds are an essential mission for public park, recreation, education, and child care agencies. The article describes how to create safety programs and offers lists of safety program components, safety inspection steps, and preventive maintenance schedules. It also presents playground safety checklists and notes three available…

  1. Remote Inspection Challenge

    ERIC Educational Resources Information Center

    Roman, Harry T.

    2013-01-01

    The ability to remotely inspect equipment of an aging infrastructure is becoming of major interest to many industries. Often the ability to just get a look at a piece of critical equipment can yield very important information. With millions of miles of piping installed throughout the United States, this vast network is critical to oil, natural…

  2. Ofsted Re-Inspected

    ERIC Educational Resources Information Center

    Coffield, Frank

    2012-01-01

    The author never thought he would have to thank Ofsted for a change in its approach that may result in a major improvement in provision; and yet, with the introduction of the revised Common Inspection Framework (CIF), it has made teaching and learning (T&L) the first priority throughout the learning and skills sector. While he wishes to…

  3. Inspecting Magic Words.

    ERIC Educational Resources Information Center

    White, John Howell

    1998-01-01

    Considers neopragmatism's use-value for art educators as they inspect the magic words, images, and practices that influence curriculum and instruction. Explains that neopragmatism offers art educators three concepts (contingency, demystification, and recontextualization) as tools to interpret educational beliefs and classroom practices. (CMK)

  4. Ofsted Re-Inspected

    ERIC Educational Resources Information Center

    Coffield, Frank

    2012-01-01

    The author never thought he would have to thank Ofsted for a change in its approach that may result in a major improvement in provision; and yet, with the introduction of the revised Common Inspection Framework (CIF), it has made teaching and learning (T&L) the first priority throughout the learning and skills sector. While he wishes to…

  5. Playground Inspection & Maintenance.

    ERIC Educational Resources Information Center

    Leeds, Gerard

    People today demand a safer work environment and a safer play environment for children. Accidents such as broken arms are no longer accepted as an inevitable part of growing up. This paper presents recommendations for the maintenance of safe playground areas and equipment, covering three main areas: (1) inspections, which should follow a specified…

  6. Additive Manufacturing Infrared Inspection

    NASA Technical Reports Server (NTRS)

    Gaddy, Darrell

    2014-01-01

    Additive manufacturing is a rapid prototyping technology that allows parts to be built in a series of thin layers from plastic, ceramics, and metallics. Metallic additive manufacturing is an emerging form of rapid prototyping that allows complex structures to be built using various metallic powders. Significant time and cost savings have also been observed using the metallic additive manufacturing compared with traditional techniques. Development of the metallic additive manufacturing technology has advanced significantly over the last decade, although many of the techniques to inspect parts made from these processes have not advanced significantly or have limitations. Several external geometry inspection techniques exist such as Coordinate Measurement Machines (CMM), Laser Scanners, Structured Light Scanning Systems, or even traditional calipers and gages. All of the aforementioned techniques are limited to external geometry and contours or must use a contact probe to inspect limited internal dimensions. This presentation will document the development of a process for real-time dimensional inspection technique and digital quality record of the additive manufacturing process using Infrared camera imaging and processing techniques.

  7. Structure and Topology of a Peptide Segment of the 6th Transmembrane Domain of the Saccharomyces cerevisae α-Factor Receptor in Phospholipid Bilayers

    PubMed Central

    Valentine, Kathleen G.; Liu, Shi-Feng; Marassi, Francesca M.; Veglia, Gianluigi; Opella, Stanley J.; Ding, Fa-Xiang; Wang, Shu-Hua; Arshava, Boris; Becker, Jeffrey M.

    2012-01-01

    A detailed analysis of the structure of an 18-residue peptide AQSLLVPSIIFILAYSLK [M6(252–269, C252A)] in 1,2-dimyristoyl-sn-glycero-phosphocholine bilayers was carried out using solid state NMR and attenuated total reflection Fourier transform infrared spectroscopy. The peptide corresponds to a portion of the 6th transmembrane domain of the α-factor receptor of Saccharomyces cerevisiae. Ten homologs of M6(252–269, C252A) were synthesized in which individual residues were labeled with 15N. One- and two-dimensional solid state NMR experiments were used to determine the chemical shifts and 1H–15N dipolar coupling constants for the 15N-labeled peptides in oriented dimyristoylphosphatidylcholine bilayers on stacked glass plates. These parameters were used to calculate the structure and orientation of M6(252–269, C252A) in the bilayers. The results indicate that the carboxyl terminal residues (9–14) are α-helical and oriented with an angle of about 8° with respect to the bilayer normal. Independently, an attenuated total reflection Fourier transform infrared spectroscopy analysis on M6(252–269, C252A) in a 1,2-dimyristoyl-sn-glycero-phosphocholine bilayer concluded that the helix tilt angle was about 12.5°. The results on the structure of M6(252–269, C252A) in bilayers are in good agreement with the structure determined in trifluoroethanol/water solutions (B. Arshava et al. Biopolymers, 1998, Vol. 46, pp. 343–357) . The present study shows that solid state NMR spectroscopy can provide high resolution information on the structure of transmembrane domains of a G protein-coupled receptor. PMID:11473349

  8. Critical issues with the in vivo comet assay: A report of the comet assay working group in the 6th International Workshop on Genotoxicity Testing (IWGT).

    PubMed

    Speit, Günter; Kojima, Hajime; Burlinson, Brian; Collins, Andrew R; Kasper, Peter; Plappert-Helbig, Ulla; Uno, Yoshifumi; Vasquez, Marie; Beevers, Carol; De Boeck, Marlies; Escobar, Patricia A; Kitamoto, Sachiko; Pant, Kamala; Pfuhler, Stefan; Tanaka, Jin; Levy, Dan D

    2015-05-01

    As a part of the 6th IWGT, an expert working group on the comet assay evaluated critical topics related to the use of the in vivo comet assay in regulatory genotoxicity testing. The areas covered were: identification of the domain of applicability and regulatory acceptance, identification of critical parameters of the protocol and attempts to standardize the assay, experience with combination and integration with other in vivo studies, demonstration of laboratory proficiency, sensitivity and power of the protocol used, use of different tissues, freezing of samples, and choice of appropriate measures of cytotoxicity. The standard protocol detects various types of DNA lesions but it does not detect all types of DNA damage. Modifications of the standard protocol may be used to detect additional types of specific DNA damage (e.g., cross-links, bulky adducts, oxidized bases). In addition, the working group identified critical parameters that should be carefully controlled and described in detail in every published study protocol. In vivo comet assay results are more reliable if they were obtained in laboratories that have demonstrated proficiency. This includes demonstration of adequate response to vehicle controls and an adequate response to a positive control for each tissue being examined. There was a general agreement that freezing of samples is an option but more data are needed in order to establish generally accepted protocols. With regard to tissue toxicity, the working group concluded that cytotoxicity could be a confounder of comet results. It is recommended to look at multiple parameters such as histopathological observations, organ-specific clinical chemistry as well as indicators of tissue inflammation to decide whether compound-specific toxicity might influence the result. The expert working group concluded that the alkaline in vivo comet assay is a mature test for the evaluation of genotoxicity and can be recommended to regulatory agencies for use.

  9. Early fetal gender determination using real-time PCR analysis of cell-free fetal DNA during 6th-10th weeks of gestation.

    PubMed

    Khorram Khorshid, Hamid Reza; Zargari, Maryam; Sadeghi, Mohammad Reza; Edallatkhah, Haleh; Shahhosseiny, Mohammad Hassan; Kamali, Koorosh

    2013-05-07

    Nowadays, new advances in the use of cell free fetal DNA (cffDNA) in maternal plasma of pregnant women has provided the possibility of applying cffDNA in prenatal diagnosis as a non-invasive method. In contrary to the risks of invasive methods that affect both mother and fetus, applying cffDNA is proven to be highly effective with lower risk. One of the applications of prenatal diagnosis is fetal gender determination, which is important in fetuses at risk of sex-linked genetic diseases. In such cases by obtaining the basic information of the gender, necessary time management can be taken in therapeutic to significantly reduce the necessity of applying the invasive methods. Therefore in this study, the probability of detecting sequences on the human Y-chromosome in pregnant women has been evaluated to identify the gender of fetuses. Peripheral blood samples were obtained from 80 pregnant women with gestational age between 6th to 10th weeks and the fetal DNA was extracted from the plasma. Identification of SRY, DYS14 & DAZ sequences, which are not presentin the maternal genome, was performed using Real-Time PCR. All the obtained results were compared with the actual gender of the newborns to calculate the test accuracy. Considerable 97.3% sensitivity and 97.3% specificity were obtained in fetal gender determination which is significant in the first trimester of pregnancy. Only in one case, false positive result was obtained. Using non-invasive method of cffDNAs in the shortest time possible, as well as avoiding invasive tests for early determination of fetal gender, provides the opportunity of deciding and employing early treatment for fetuses at risk of genetic diseases.

  10. From Inspection to School Improvement? Evaluating the Accelerated Inspection Programme in Waltham Forest.

    ERIC Educational Resources Information Center

    Hopkins, David; Harris, Alma; Watling, Rob; Beresford, John

    1999-01-01

    Outlines the main findings from the evaluation of the Accelerated Inspection Programme (AIP) in Waltham Forest under three main phases (pre-inspection, inspection, and post inspection). Focuses on the relationship between inspection and school improvement. Discusses the recommendations. (CMK)

  11. From Inspection to School Improvement? Evaluating the Accelerated Inspection Programme in Waltham Forest.

    ERIC Educational Resources Information Center

    Hopkins, David; Harris, Alma; Watling, Rob; Beresford, John

    1999-01-01

    Outlines the main findings from the evaluation of the Accelerated Inspection Programme (AIP) in Waltham Forest under three main phases (pre-inspection, inspection, and post inspection). Focuses on the relationship between inspection and school improvement. Discusses the recommendations. (CMK)

  12. Flexible ultrasonic pipe inspection apparatus

    DOEpatents

    Jenkins, C.F.; Howard, B.D.

    1994-01-01

    Pipe crawlers, pipe inspection {open_quotes}rabbits{close_quotes} and similar vehicles are widely used for inspecting the interior surfaces of piping systems, storage tanks and process vessels for damaged or flawed structural features. This paper describes the design of a flexible, modular ultrasonic pipe inspection apparatus.

  13. Multi-Sensor Inspection Telerobot

    NASA Technical Reports Server (NTRS)

    Balaram, J.; Hayati, S.; Volpe, R.

    1994-01-01

    This paper describes a telerobotic multi-sensor inspection system for space platforms developed at the Jet Propulsion Laboratory. A multi-sensor inspection end-effector incorporates cameras and lighting for visual inspection, as well as temperature and gas leak-detection sensors.

  14. Rotating regular black hole solution

    NASA Astrophysics Data System (ADS)

    Abdujabbarov, Ahmadjon

    2016-07-01

    Based on the Newman-Janis algorithm, the Ayón-Beato-García spacetime metric [Phys. Rev. Lett. 80, 5056 (1998)] of the regular spherically symmetric, static, and charged black hole has been converted into rotational form. It is shown that the derived solution for rotating a regular black hole is regular and the critical value of the electric charge for which two horizons merge into one sufficiently decreases in the presence of the nonvanishing rotation parameter a of the black hole.

  15. 23 CFR 650.313 - Inspection procedures.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS BRIDGES, STRUCTURES, AND HYDRAULICS National Bridge Inspection Standards § 650.313 Inspection procedures. (a) Inspect each bridge in accordance with the inspection procedures in the AASHTO Manual (incorporated by...

  16. 23 CFR 650.313 - Inspection procedures.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS BRIDGES, STRUCTURES, AND HYDRAULICS National Bridge Inspection Standards § 650.313 Inspection procedures. (a) Inspect each bridge in accordance with the inspection procedures in the AASHTO Manual (incorporated by...

  17. Overview of the software inspection process

    SciTech Connect

    Lane, G.L.; Dabbs, R.

    1997-11-01

    This tutorial introduces attendees to the Inspection Process and teaches them how to organize and participate in a software inspection. The tutorial advocates the benefits of inspections and encourages attendees to socialize the inspection process in their organizations.

  18. Military History of the American Revolution. Proceedings of the Military History Symposium (6th) Held at the Air Force Academy, Colo. on 10-11 October 1974,

    DTIC Science & Technology

    1976-01-01

    in 1776 and not maintained subsequently because forces were dispersed ."• Evidence that the timing of the Dcclaratior. wi independence was in part...that it was determined to make them submit by taking or sinking their ships, devastating their ports, destroying their armed forces, and dispersing ...Still, it was confident that such a force of regulars would be able to disperse any number of untrained colonists and that Britain would gain a

  19. National Dam Inspection Program. Belmont Dam (NDI-ID Number PA-00252, DER-ID 35-33), Susquehanna River Basin, Lackawanna County, Pennsylvania. Phase I Inspection Report,

    DTIC Science & Technology

    1980-08-01

    inspection check list is in Appendix A of this report. Sketches of a general plan , profile and typical cross sections as surveyed during the inspection are...on a regular basis. Valves should be maintained and operate~d on an annual basis. A formal surveillance plan and downstream warning system should be...end of reservoir breached in sixties. GENERAL PLAN OF DAM Not available. See sketch Plate A-I, Appendix A. TYPICAL SECTIONS Plates III and IV

  20. How Do 4th, 5th, and 6th Grade Students' Categories of Cognitive Reflections in Interviews on Derivational Morphology Compare to Their Upper Level Spelling Inventory Orthographic Knowledge?

    ERIC Educational Resources Information Center

    Smith, Darcie D.

    2012-01-01

    Eighty-seven 4th, 5th and 6th grade students were administered the "Derivational Relatedness Interview" (DRI) (Templeton, Smith, Moloney, Van Pelt, & Ives, 2009). The purpose of this instrument is to explore students' understanding of derivational morphology. During the same week, the subjects were also administered an Upper…

  1. Study of the Effects on Student Knowledge and Perceptions of Activities Related to Submetering the 6th Grade Wing of a Middle School, to Displaying the Carbon Footprint, and to Efforts to Reduce Energy Consumption and Greenhouse Gases

    ERIC Educational Resources Information Center

    Peck, Rick

    2009-01-01

    The purpose of the study was to determine the effects upon student knowledge and perceptions regarding greenhouse gas emissions as a result of an intervention relying upon the submetering the 6th grade wing of a Middle School, displaying the information regarding electrical consumption and carbon footprint, and reducing the electrical consumption…

  2. Inspection challenges -- pigs versus pipes

    SciTech Connect

    Holden, E.M.; Grimes, K.

    1996-12-31

    As the size of the international pipeline network grows, and systems age (by the year 2000, over 50% of US gas transmission pipelines will be over 40 years old), and as environmental pressures increase, the demand for inspection is ever more apparent. Pipeline operations` experience has revealed many new defects and new inspection problems, many of which have challenged in-line inspection technology and stimulated further developments. This paper describes what pipeline inspection needs to find, the available technology and some examples of the inspection challenges.

  3. Industrial Inspection System

    NASA Technical Reports Server (NTRS)

    1993-01-01

    Lixi, Inc. has built a thriving business on NASA-developed x-ray technology. The Low Intensity X-ray Imaging scope (LIXI) was designed to use less than one percent of radiation required by conventional x-ray devices. It is portable and can be used for a variety of industrial inspection systems as well as medical devices. A food processing plant uses the new LIXI Conveyor system to identify small bone fragments in chicken. The chicken packages on a conveyor belt enter an x-ray chamber and the image is displayed on a monitor. Defects measuring less than a millimeter can be detected. An important advantage of the system is its ability to inspect 100 percent of the product right on the production line.

  4. Advanced Via Inspection Tool

    NASA Astrophysics Data System (ADS)

    Kim, Douglas Y.; Muller, Kurt; Thorp, Lawrence D.; Bird, Kenneth A.

    1992-08-01

    The AVIT inspects vias on unfired ceramic layers used in microelectronic packaging for paste fill depth spacing and size. Four shadow images from different angles and one vertical image determine the fill status of 100 89um vias in the area of 160mm by 160mm. Each via is filled with a conductive paste. The cycle time to inspect a greensheet is 3. 75 seconds. The paste depth is determined by the area of shadow given by each oblique direction. The greater area of shadow is used to determine via depth. In order to achieve the cycle time of 3. 75 seconds we incorporate a laser scanner rotating at 28 rpm telecentric scan lens and dedicated signal processing one of the electronic racks uses ECL running at 87 MHz. The other electronics are predominant Fast-TTL.

  5. Nondestructive inspection perspectives

    NASA Technical Reports Server (NTRS)

    Froom, Douglas A.

    1992-01-01

    This paper presents ideas for consideration by those concerned with commercial aircraft nondestructive inspection (NDI). The perspective is that of an individual with a background in military aircraft NDI, and important differences are indicated between the commercial NDI and military NDI activities. In particular, it is significantly more expensive to implement some new NDI technology, and therefore, in-depth cost-benifit studies for commercial users are recommended.

  6. Printed Circuit Board Inspection.

    DTIC Science & Technology

    1981-11-25

    8217, but copper is etched off a smoothly plated board to form the ’printed circuit.’ The etching, as the name implies, leaves a three- 6 Figure 3-2...e.g., dust on the light- plate used to transfer the board design from the artwork negative). The information output must be verifiable -. if only to...Carnegie-Mellon University 00 PRINTED CIRCUIT BOARD INSPECTION W ~Robert Thibadeau -= The Robotics Institute Carnegie-Mellon University Pittsburgh

  7. Infrared microscope inspection apparatus

    DOEpatents

    Forman, S.E.; Caunt, J.W.

    1985-02-26

    Apparatus and system for inspecting infrared transparents, such as an array of photovoltaic modules containing silicon solar cells, includes an infrared microscope, at least three sources of infrared light placed around and having their axes intersect the center of the object field and means for sending the reflected light through the microscope. The apparatus is adapted to be mounted on an X-Y translator positioned adjacent the object surface. 4 figs.

  8. Expedition 8 Capsule Inspection

    NASA Image and Video Library

    2003-10-13

    Expedition 8 Commander and NASA Science Officer Michael Foale, left, Expedition 8 Soyuz Commander Alexander Kaleri and European Space Agency Astronaut Pedro Duque of Spain, right, report to launch officials on their inspection of the Soyuz TMA-3 spacecraft during a final vehicle training session at the Baikonur Cosmodrome in Kazakhstan, Monday, Oct. 13, 2003. The trio launched to the International Space Station on Oct. 18, 2003. Photo Credit (NASA/Bill Ingalls)

  9. Inspection tester for explosives

    DOEpatents

    Haas, Jeffrey S.; Simpson, Randall L.; Satcher, Joe H.

    2007-11-13

    An inspection tester that can be used anywhere as a primary screening tool by non-technical personnel to determine whether a surface contains explosives. It includes a body with a sample pad. First and second explosives detecting reagent holders and dispensers are operatively connected to the body and the sample pad. The first and second explosives detecting reagent holders and dispensers are positioned to deliver the explosives detecting reagents to the sample pad. A is heater operatively connected to the sample pad.

  10. Inspection tester for explosives

    DOEpatents

    Haas, Jeffrey S.; Simpson, Randall L.; Satcher, Joe H.

    2010-10-05

    An inspection tester that can be used anywhere as a primary screening tool by non-technical personnel to determine whether a surface contains explosives. It includes a body with a sample pad. First and second explosives detecting reagent holders and dispensers are operatively connected to the body and the sample pad. The first and second explosives detecting reagent holders and dispensers are positioned to deliver the explosives detecting reagents to the sample pad. A is heater operatively connected to the sample pad.

  11. Waste Inspection Tomography (WIT)

    SciTech Connect

    Bernardi, R.T.

    1995-12-01

    Waste Inspection Tomography (WIT) provides mobile semi-trailer mounted nondestructive examination (NDE) and assay (NDA) for nuclear waste drum characterization. WIT uses various computed tomography (CT) methods for both NDE and NDA of nuclear waste drums. Low level waste (LLW), transuranic (TRU), and mixed radioactive waste can be inspected and characterized without opening the drums. With externally transmitted x-ray NDE techniques, WIT has the ability to identify high density waste materials like heavy metals, define drum contents in two- and three-dimensional space, quantify free liquid volumes through density and x-ray attenuation coefficient discrimination, and measure drum wall thickness. With waste emitting gamma-ray NDA techniques, WIT can locate gamma emitting radioactive sources in two- and three-dimensional space, identify gamma emitting isotopic species, identify the external activity levels of emitting gamma-ray sources, correct for waste matrix attenuation, provide internal activity approximations, and provide the data needed for waste classification as LLW or TRU. The mobile feature of WIT allows inspection technologies to be brought to the nuclear waste drum storage site without the need to relocate drums for safe, rapid, and cost-effective characterization of regulated nuclear waste. The combination of these WIT characterization modalities provides the inspector with an unprecedented ability to non-invasively characterize the regulated contents of waste drums as large as 110 gallons, weighing up to 1,600 pounds. Any objects that fit within these size and weight restrictions can also be inspected on WIT, such as smaller waste bags and drums that are five and thirty-five gallons.

  12. Infrared microscope inspection apparatus

    DOEpatents

    Forman, Steven E.; Caunt, James W.

    1985-02-26

    Apparatus and system for inspecting infrared transparents, such as an array of photovoltaic modules containing silicon solar cells, includes an infrared microscope, at least three sources of infrared light placed around and having their axes intersect the center of the object field and means for sending the reflected light through the microscope. The apparatus is adapted to be mounted on an X-Y translator positioned adjacent the object surface.

  13. Code inspection instructional validation

    NASA Technical Reports Server (NTRS)

    Orr, Kay; Stancil, Shirley

    1992-01-01

    The Shuttle Data Systems Branch (SDSB) of the Flight Data Systems Division (FDSD) at Johnson Space Center contracted with Southwest Research Institute (SwRI) to validate the effectiveness of an interactive video course on the code inspection process. The purpose of this project was to determine if this course could be effective for teaching NASA analysts the process of code inspection. In addition, NASA was interested in the effectiveness of this unique type of instruction (Digital Video Interactive), for providing training on software processes. This study found the Carnegie Mellon course, 'A Cure for the Common Code', effective for teaching the process of code inspection. In addition, analysts prefer learning with this method of instruction, or this method in combination with other methods. As is, the course is definitely better than no course at all; however, findings indicate changes are needed. Following are conclusions of this study. (1) The course is instructionally effective. (2) The simulation has a positive effect on student's confidence in his ability to apply new knowledge. (3) Analysts like the course and prefer this method of training, or this method in combination with current methods of training in code inspection, over the way training is currently being conducted. (4) Analysts responded favorably to information presented through scenarios incorporating full motion video. (5) Some course content needs to be changed. (6) Some content needs to be added to the course. SwRI believes this study indicates interactive video instruction combined with simulation is effective for teaching software processes. Based on the conclusions of this study, SwRI has outlined seven options for NASA to consider. SwRI recommends the option which involves creation of new source code and data files, but uses much of the existing content and design from the current course. Although this option involves a significant software development effort, SwRI believes this option

  14. Combined PET/MRI: Global Warming-Summary Report of the 6th International Workshop on PET/MRI, March 27-29, 2017, Tübingen, Germany.

    PubMed

    Bailey, D L; Pichler, B J; Gückel, B; Antoch, G; Barthel, H; Bhujwalla, Z M; Biskup, S; Biswal, S; Bitzer, M; Boellaard, R; Braren, R F; Brendle, C; Brindle, K; Chiti, A; la Fougère, C; Gillies, R; Goh, V; Goyen, M; Hacker, M; Heukamp, L; Knudsen, G M; Krackhardt, A M; Law, I; Morris, J C; Nikolaou, K; Nuyts, J; Ordonez, A A; Pantel, K; Quick, H H; Riklund, K; Sabri, O; Sattler, B; Troost, E G C; Zaiss, M; Zender, L; Beyer, Thomas

    2017-10-02

    The 6th annual meeting to address key issues in positron emission tomography (PET)/magnetic resonance imaging (MRI) was held again in Tübingen, Germany, from March 27 to 29, 2017. Over three days of invited plenary lectures, round table discussions and dialogue board deliberations, participants critically assessed the current state of PET/MRI, both clinically and as a research tool, and attempted to chart future directions. The meeting addressed the use of PET/MRI and workflows in oncology, neurosciences, infection, inflammation and chronic pain syndromes, as well as deeper discussions about how best to characterise the tumour microenvironment, optimise the complementary information available from PET and MRI, and how advanced data mining and bioinformatics, as well as information from liquid biomarkers (circulating tumour cells and nucleic acids) and pathology, can be integrated to give a more complete characterisation of disease phenotype. Some issues that have dominated previous meetings, such as the accuracy of MR-based attenuation correction (AC) of the PET scan, were finally put to rest as having been adequately addressed for the majority of clinical situations. Likewise, the ability to standardise PET systems for use in multicentre trials was confirmed, thus removing a perceived barrier to larger clinical imaging trials. The meeting openly questioned whether PET/MRI should, in all cases, be used as a whole-body imaging modality or whether in many circumstances it would best be employed to give an in-depth study of previously identified disease in a single organ or region. The meeting concluded that there is still much work to be done in the integration of data from different fields and in developing a common language for all stakeholders involved. In addition, the participants advocated joint training and education for individuals who engage in routine PET/MRI. It was agreed that PET/MRI can enhance our understanding of normal and disrupted biology, and we

  15. EDITORIAL: The 6th International Workshop on Micro and Nanotechnologies for Power Generation and Energy Conversion Applications (PowerMEMS 2006)

    NASA Astrophysics Data System (ADS)

    Fréchette, Luc G.

    2007-09-01

    Energy is a sector of paramount importance over the coming decades if we are to ensure sustainable development that respects our environment. The research and development of novel approaches to convert available energy into usable forms using micro and nanotechnologies can contribute towards this goal and meet the growing need for power in small scale portable applications. The dominant power sources for handheld and other portable electronics are currently primary and rechargeable batteries. Their limited energy density and adverse effects on the environment upon disposal suggest that alternative approaches need to be explored. This special issue will showcase some of the leading work in this area, initially presented at PowerMEMS 2006, the 6th International Workshop on Micro and Nanotechnologies for Power Generation and Energy Conversion Applications. Power MEMS are defined as microsystems for electrical power generation and other energy conversion applications, including propulsion and cooling. The range of power MEMS technologies includes micro thermodynamic machines, such as microturbines, miniature internal combustion engines and micro-coolers; solid-state direct energy conversion, such as thermoelectric and photovoltaic microstructures; micro electrochemical devices, such as micro fuel cells and nanostructure batteries; vibration energy harvesting devices, such as piezoelectric, magnetic or electrostatic micro generators, as well as micro thrusters and rocket engines for propulsion. These can either be driven by scavenging thermal, mechanical or solar energy from the environment, or from a stored energy source, such as chemical fuel or radioactive material. The unique scope leads to unique challenges in the development of power MEMS, ranging from the integration of novel materials to the efficient small scale implementation of energy conversion principles. In this special issue, Mitcheson et al provide a comparative assessment of three inertial vibration

  16. Process evaluation for a school-based physical activity intervention for 6th- and 7th-grade boys: reach, dose, and fidelity.

    PubMed

    Robbins, Lorraine B; Pfeiffer, Karin Allor; Wesolek, Stacey M; Lo, Yun-Jia

    2014-02-01

    The purpose was to evaluate the reach, dose, and fidelity of Guys Only Activity for Life (G.O.A.L.), a 7-week pilot intervention conducted from February to March 2011 to increase 6th and 7th grade boys' moderate-to-vigorous physical activity (MVPA). One middle school was randomly assigned to the G.O.A.L. intervention and another from the same urban school district in the Midwestern U.S. to a comparison condition. Thirty boys, ages 10-14 years, participated in each school. The intervention, guided by the Health Promotion Model (HPM) and Self-Determination Theory (SDT), consisted of a 90-min after-school physical activity club 4 days/week and one motivational interviewing session with a registered (school) nurse. Data were gathered via attendance records, club observations, heart rate monitors, audio-taping of motivational interviewing sessions, and surveys. On average boys attended the club 2.11 days/week (SD=.86). A trained independent process evaluator reported that the physical activity club instructors provided the boys with the opportunity for a mean of 25.8 min/day of MVPA. Using a four-point Likert scale (1=disagree a lot; 4=agree a lot), the process evaluator perceived that the club was delivered with high fidelity and adherence to the underlying theories (M=3.48; SD=0.39). Sessions with the nurse lasted an average of 13 min, 29 s. All boys attended. Two trained independent coders indicated that the nurse demonstrated at least beginning proficiency for all tasks associated with motivational interviewing, with the exception of using sufficient open- as opposed to closed-ended questions and reflections compared to questions. Fidelity related to session delivery and adherence to the theories was high (M=3.83; SD=0.19). The process evaluation data indicated that strategies are needed to increase attendance and boys' MVPA during the club time. Copyright © 2013 Elsevier Ltd. All rights reserved.

  17. Emergency Preparedness and Management at the University of L’aquila (Central Italy) and the Role of Students’ Associations in the April 6th 2009 Earthquake

    PubMed Central

    Magni, Michele; Fraboni, Rita; Marincioni, Fausto

    2017-01-01

    Introduction: On April 6th 2009 an earthquake of Mw=6.3 hit the historical downtown of L’Aquila and its hinterland causing more than 300 fatalities and severe damage to private and public buildings. At the time, the University of L’Aquila represented a major source of employment and income for the city. The earthquake impacted both the facilities and the administrative, financial and patrimonial activities of the university, bringing into the open the tendency – widespread in Italy – to rely on adaptive tactics rather than on strategic pre-disaster plans. This paper investigates the university’s emergency preparedness and response capability and  the strategies adopted to restore the education activities as well as avoid students migration to other universities. In addition, emphasis is placed on the role played by Student Associations in pre and post-disaster phases, and how students perceived the activities performed by these associations. Methods: To achieve this goal, it was undertaken: i) qualitative evaluation to assess the impact of earthquake on services and facilities of the university, the emergency preparedness and the measures adopted to face the emergency, ii) survey on the role played by Student Associations, both in emergency preparedness and response, according to students’ perception; iii) quantitative analysis to measure changes in the enrollment trend after the earthquake, and how university policies could curb students’ migration. Results: The policies adopted by the University allowed to diminish students’ migration; however, the measures taken by the university were based on an ad hoc plan as no emergency and continuity plans were prepared in advance. Similarly Student Associations got involved more in restoration activities than in emergency preparedness and risk awareness promotion. Discussion: Greater awareness and involvement are essential at each level (administrators, faculties, students) to plan in advance for an

  18. NONCONVEX REGULARIZATION FOR SHAPE PRESERVATION

    SciTech Connect

    CHARTRAND, RICK

    2007-01-16

    The authors show that using a nonconvex penalty term to regularize image reconstruction can substantially improve the preservation of object shapes. The commonly-used total-variation regularization, {integral}|{del}u|, penalizes the length of the object edges. They show that {integral}|{del}u|{sup p}, 0 < p < 1, only penalizes edges of dimension at least 2-p, and thus finite-length edges not at all. We give numerical examples showing the resulting improvement in shape preservation.

  19. Condition Number Regularized Covariance Estimation.

    PubMed

    Won, Joong-Ho; Lim, Johan; Kim, Seung-Jean; Rajaratnam, Bala

    2013-06-01

    Estimation of high-dimensional covariance matrices is known to be a difficult problem, has many applications, and is of current interest to the larger statistics community. In many applications including so-called the "large p small n" setting, the estimate of the covariance matrix is required to be not only invertible, but also well-conditioned. Although many regularization schemes attempt to do this, none of them address the ill-conditioning problem directly. In this paper, we propose a maximum likelihood approach, with the direct goal of obtaining a well-conditioned estimator. No sparsity assumption on either the covariance matrix or its inverse are are imposed, thus making our procedure more widely applicable. We demonstrate that the proposed regularization scheme is computationally efficient, yields a type of Steinian shrinkage estimator, and has a natural Bayesian interpretation. We investigate the theoretical properties of the regularized covariance estimator comprehensively, including its regularization path, and proceed to develop an approach that adaptively determines the level of regularization that is required. Finally, we demonstrate the performance of the regularized estimator in decision-theoretic comparisons and in the financial portfolio optimization setting. The proposed approach has desirable properties, and can serve as a competitive procedure, especially when the sample size is small and when a well-conditioned estimator is required.

  20. Condition Number Regularized Covariance Estimation*

    PubMed Central

    Won, Joong-Ho; Lim, Johan; Kim, Seung-Jean; Rajaratnam, Bala

    2012-01-01

    Estimation of high-dimensional covariance matrices is known to be a difficult problem, has many applications, and is of current interest to the larger statistics community. In many applications including so-called the “large p small n” setting, the estimate of the covariance matrix is required to be not only invertible, but also well-conditioned. Although many regularization schemes attempt to do this, none of them address the ill-conditioning problem directly. In this paper, we propose a maximum likelihood approach, with the direct goal of obtaining a well-conditioned estimator. No sparsity assumption on either the covariance matrix or its inverse are are imposed, thus making our procedure more widely applicable. We demonstrate that the proposed regularization scheme is computationally efficient, yields a type of Steinian shrinkage estimator, and has a natural Bayesian interpretation. We investigate the theoretical properties of the regularized covariance estimator comprehensively, including its regularization path, and proceed to develop an approach that adaptively determines the level of regularization that is required. Finally, we demonstrate the performance of the regularized estimator in decision-theoretic comparisons and in the financial portfolio optimization setting. The proposed approach has desirable properties, and can serve as a competitive procedure, especially when the sample size is small and when a well-conditioned estimator is required. PMID:23730197

  1. Geometric continuum regularization of quantum field theory

    SciTech Connect

    Halpern, M.B. . Dept. of Physics)

    1989-11-08

    An overview of the continuum regularization program is given. The program is traced from its roots in stochastic quantization, with emphasis on the examples of regularized gauge theory, the regularized general nonlinear sigma model and regularized quantum gravity. In its coordinate-invariant form, the regularization is seen as entirely geometric: only the supermetric on field deformations is regularized, and the prescription provides universal nonperturbative invariant continuum regularization across all quantum field theory. 54 refs.

  2. Experimental validation of MCNP simulations for the EURITRACK Tagged Neutron Inspection System

    NASA Astrophysics Data System (ADS)

    Donzella, A.; Bodini, I.; Zenoni, A.; Fontana, A.; Perot, B.; Bernard, S.; Carasco, C.; Mariani, A.; Sudac, D.; Valkovic, V.

    2007-08-01

    The detection of illicit trafficking such as explosive materials inside large commercial payloads is today an important worldwide problem. Differently from the X- or γ-ray based systems, neutron interrogation allows the elemental composition of inspected materials to be measured. A container interrogation device based on the Tagged Neutron Inspection System (TNIS) has been developed within the EURITRACK (EURopean Illicit TRAfficking Countermeasures Kit) project of the 6th Framework Program of the European Union. A prototype of such system has been integrated at the Ruder Boskovic Institute (IRB) of Zagreb, Croatia, and performance tests have been carried out. A detailed simulation of the IRB experimental set-up has been performed. Comparison of the Monte Carlo predictions with collected experimental data is presented.

  3. Compressing Regular Expressions' DFA Table by Matrix Decomposition

    NASA Astrophysics Data System (ADS)

    Liu, Yanbing; Guo, Li; Liu, Ping; Tan, Jianlong

    Recently regular expression matching has become a research focus as a result of the urgent demand for Deep Packet Inspection (DPI) in many network security systems. Deterministic Finite Automaton (DFA), which recognizes a set of regular expressions, is usually adopted to cater to the need for real-time processing of network traffic. However, the huge memory usage of DFA prevents it from being applied even on a medium-sized pattern set. In this article, we propose a matrix decomposition method for DFA table compression. The basic idea of the method is to decompose a DFA table into the sum of a row vector, a column vector and a sparse matrix, all of which cost very little space. Experiments on typical rule sets show that the proposed method significantly reduces the memory usage and still runs at fast searching speed.

  4. Infusion pump inspection frequencies. How often is inspection really needed?

    PubMed

    1998-01-01

    As noted in this issue's Evaluation of infusion pump analyzers, the frequency at which a facility inspects its infusion pumps can help determine its need for one or more analyzers. It can also have a financial impact on the clinical engineering department. In this article, we discuss inspection issues affecting infusion pumps, including our recommendations and how facilities can set intervals for their equipment. (For ECRI's procedure for inspecting infusion devices, refer to Procedure/Checklist 416-0595 in the Health Devices Inspection and Preventive Maintenance [IPM] System; contact ECRI's Communications Department at [610] 825-6000, ext. 888, for more information about this publication.)

  5. Pellet inspection apparatus

    DOEpatents

    Wilks, Robert S.; Taleff, Alexander; Sturges, Jr., Robert H.

    1982-01-01

    Apparatus for inspecting nuclear fuel pellets in a sealed container for diameter, flaws, length and weight. The apparatus includes, in an array, a pellet pick-up station, four pellet inspection stations and a pellet sorting station. The pellets are delivered one at a time to the pick-up station by a vibrating bowl through a vibrating linear conveyor. Grippers each associated with a successive pair of the stations are reciprocable together to pick up a pellet at the upstream station of each pair and to deposit the pellet at the corresponding downstream station. The gripper jaws are opened selectively depending on the state of the pellets at the stations and the particular cycle in which the apparatus is operating. Inspection for diameter, flaws and length is effected in each case by a laser beam projected on the pellets by a precise optical system while each pellet is rotated by rollers. Each laser and its optical system are mounted in a container which is free standing on a precise surface and is provided with locating buttons which engage locating holes in the surface so that each laser and its optical system is precisely set. The roller stands are likewise free standing and are similarly precisely positioned. The diameter optical system projects a thin beam of light which scans across the top of each pellet and is projected on a diode array. The fl GOVERNMENT CONTRACT CLAUSE The invention herein described was made in the course of or under a contract or subcontract thereunder with the Department of Energy bearing No. EY-67-14-C-2170.

  6. Laser Safety Inspection Criteria

    SciTech Connect

    Barat, K

    2005-06-13

    A responsibility of the Laser Safety Officer (LSO) is to perform laser audits. The American National Standard Z136.1 Safe Use of Lasers references this requirement through several sections. One such reference is Section 1.3.2.8, Safety Features Audits, ''The LSO shall ensure that the safety features of the laser installation facilities and laser equipment are audited periodically to assure proper operation''. The composition, frequency and rigor of that inspection/audit rests in the hands of the LSO. A common practice for institutions is to develop laser audit checklists or survey forms It is common for audit findings from one inspector or inspection to the next to vary even when reviewing the same material. How often has one heard a comment, ''well this area has been inspected several times over the years and no one ever said this or that was a problem before''. A great number of audit items, and therefore findings, are subjective because they are based on the experience and interest of the auditor to particular items on the checklist. Beam block usage, to one set of eyes might be completely adequate, while to another, inadequate. In order to provide consistency, the Laser Safety Office of the National Ignition Facility Directorate has established criteria for a number of items found on the typical laser safety audit form. The criteria are distributed to laser users. It serves two broad purposes; first, it gives the user an expectation of what will be reviewed by an auditor. Second, it is an opportunity to explain audit items to the laser user and thus the reasons for some of these items, such as labelling of beam blocks.

  7. Safeguards management inspection procedures

    SciTech Connect

    Barth, M.J.; Dunn, D.R.

    1984-08-01

    The objective of this inspection module is to independently assess the contributions of licensee management to overall safeguards systems performance. The inspector accomplishes this objective by comparing the licensee's safeguards management to both the 10 CFR, parts 70 and 73, requirements and to generally accepted management practices. The vehicle by which this comparison is to be made consists of assessment questions and key issues which point the inspector to areas of primary concern to the NRC and which raise additional issues for the purpose of exposing management ineffectiveness. Further insight into management effectiveness is obtained through those assessment questions specifically directed toward the licensee's safeguards system performance. If the quality of the safeguards is poor, then the inspector should strongly suspect that management's role is ineffective and should attempt to determine management's influence (or lack thereof) on the underlying safeguards deficiencies. (The converse is not necessarily true, however.) The assessment questions in essence provide an opportunity for the inspector to identify, to single out, and to probe further, questionable management practices. Specific issues, circumstances, and concerns which point to questionable or inappropriate practices should be explicitly identified and referenced against the CFR and the assessment questions. The inspection report should also explain why the inspector feels certain management practices are poor, counter to the CFR, and/or point to ineffecive management. Concurrent with documenting the inspection results, the inspector should provide recommendations for alleviating observed management practices that are detrimental to effective safeguards. The recommendations could include: specific changes in the practices of the licensee, followup procedures on the part of NRC, and proposed license changes.

  8. Acoustic inspection device

    DOEpatents

    Diaz, Aaron A.; Burghard, Brion J.; Skorpik, James R.; Pappas, Richard A.; Mullen, O. Dennis; Samuel, Todd J.; Reid, Larry D.; Harris, Joe C.; Valencia, Juan D.; Smalley, Jonathan T.; Shepard, Chester L.; Taylor, Theodore T.

    2005-09-06

    An ultrasound inspection apparatus particularly adapted to examine containers (sealed or unsealed) containing a liquid or solid bulk material. The apparatus has an overall configuration of a hand held pistol with a front transducer contact surface that is positioned against a front wall of the container. An ultrasound pulse is transmitted from the apparatus to be reflected from a back wall of a container being investigated. The received echo pulse is converted to a digital waveform. The waveform is analyzed relative to temperature, travel distance of the pulse(s), and time of travel to ascertain characteristics of the liquid or other materials and to provide identification of the same.

  9. Inspecting the MIRI Cryocooler

    NASA Image and Video Library

    2016-06-13

    Technicians inspect a component of the cryocooler for the Mid-Infrared Instrument, or MIRI, part of NASA's James Webb Space Telescope. This photo was taken after the cooler had completed testing, and was taken out of the test chamber in preparation for being placed into its shipping container. The cooler was shipped to the Northrop Grumman Aerospace Systems facility in Redondo Beach, California, on May 26, 2016. There, the cooler will be attached to the body of the Webb telescope. http://photojournal.jpl.nasa.gov/catalog/PIA20686

  10. Visual Inspection of Surfaces

    NASA Technical Reports Server (NTRS)

    Hughes, David; Perez, Xavier

    2007-01-01

    This presentation evaluates the parameters that affect visual inspection of cleanliness. Factors tested include surface reflectance, surface roughness, size of the largest particle, exposure time, inspector and distance from sample surface. It is concluded that distance predictions were not great, particularly because the distance at which contamination is seen may depend on more variables than those tested. Most parameters estimates had confidence of 95% or better, except for exposure and reflectance. Additionally, the distance at which surface is visibly contaminated decreases with increasing reflectance, roughness, and exposure. The distance at which the surface is visually contaminated increased with the largest particle size. These variables were only slightly affected the observer.

  11. Inspection Methods in Programming.

    DTIC Science & Technology

    1981-06-01

    ADI A 0 030 MASSACHUSETTS INST OF TECH CAMBRIDGE ARTIFICIAL INTE--ETC F/ G 9/2 INSPECTION METHODS IN PROGRAMMING. (U) JUN al C RICH N00014-75-C-0643...problem with flowchart schemas can be fixed by combining flowchart schemas with another network-like formalism, the dalaflow schemas of Dennis [191...presumably involve a much stronger control structure for hypothesis formation and testing. W- g A-. 94 QIAVrM FIVE tCofruv.CAL A lb It TLtc - r+iVp

  12. Ceramic inspection system

    DOEpatents

    Werve, Michael E.

    2006-05-16

    A system for inspecting a ceramic component. The ceramic component is positioned on a first rotary table. The first rotary table rotates the ceramic component. Light is directed toward the first rotary table and the rotating ceramic component. A detector is located on a second rotary table. The second rotary table is operably connected to the first rotary table and the rotating ceramic component. The second rotary table is used to move the detector at an angle to the first rotary table and the rotating ceramic component.

  13. Electrostatic Levitator Inspected

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Larry Savage, Dr. Jan Rogers, Dr. Michael Robinson (All NASA) and Doug Huie (Mevatec) inspect the Electrostatic Levitator (ESL) at NASA's Marshall Space Flight Center (MSFC). The ESL uses static electricity to suspend an object (about 2-3 mm in diameter) inside a vacuum chamber while a laser heats the sample until it melts. This lets scientists record a wide range of physical properties without the sample contacting the container or any instruments, conditions that would alter the readings. The Electrostatic Levitator is one of several tools used in NASA's microgravity materials science program.

  14. Word regularity affects orthographic learning.

    PubMed

    Wang, Hua-Chen; Castles, Anne; Nickels, Lyndsey

    2012-01-01

    Share's self-teaching hypothesis proposes that orthographic representations are acquired via phonological decoding. A key, yet untested, prediction of this theory is that there should be an effect of word regularity on the number and quality of word-specific orthographic representations that children acquire. Thirty-four Grade 2 children were exposed to the sound and meaning of eight novel words and were then presented with those words in written form in short stories. Half the words were assigned regular pronunciations and half irregular pronunciations. Lexical decision and spelling tasks conducted 10 days later revealed that the children's orthographic representations of the regular words appeared to be stronger and more extensive than those of the irregular words.

  15. Ultrasonic inspection of reactor systems

    SciTech Connect

    Majzlik, E.J. Jr.

    1989-01-01

    The subject of this presentation is ultrasonic inspection of reactor systems. This paper describes two current programs underway at Savannah River Site which provide state-of-the-art ultrasonic inspections of weld heat-affected zones in the primary cooling loop of the Savannah River Site reactors. It also describes the automated remote inspection equipment being developed and employed; briefly describe the procedures being used; and give you a general idea of the future direction of two major programs: Moderator Piping Inspection Program and the Reactor Tank Wall Weld Inspection Program. The objective of these programs is to provide inspection techniques to more fully determine the condition of the reactor primary system and provide data for prediction of maintenance needs and remaining service life. Detection and sizing of intergranular stress corrosion cracking is the focus of these programs.

  16. Dimensional regularization in configuration space

    SciTech Connect

    Bollini, C.G. |; Giambiagi, J.J.

    1996-05-01

    Dimensional regularization is introduced in configuration space by Fourier transforming in {nu} dimensions the perturbative momentum space Green functions. For this transformation, the Bochner theorem is used; no extra parameters, such as those of Feynman or Bogoliubov and Shirkov, are needed for convolutions. The regularized causal functions in {ital x} space have {nu}-dependent moderated singularities at the origin. They can be multiplied together and Fourier transformed (Bochner) without divergence problems. The usual ultraviolet divergences appear as poles of the resultant analytic functions of {nu}. Several examples are discussed. {copyright} {ital 1996 The American Physical Society.}

  17. Flexible Borescope For Inspecting Ducts

    NASA Technical Reports Server (NTRS)

    Shinozaki, Keith; Armstrong, Mike P.; Urquidi, Ron

    1995-01-01

    Borescope and associated equipment developed specifically for use in optical inspection of inside of flexible joints in rocket-engine fuel duct. Apparatus includes assembly, characterized as "mouse/canoe," at sensing end of 10-ft borescope cable. Borescope tip rides in mouse/canoe. The mouse/canoe made laterally compressible, to facilitate movement past constrictions and provides fixed distance from inspection point permitting accurate description in duct inspected.

  18. Inspection system performance test procedure

    SciTech Connect

    Jensen, C.E.

    1995-01-17

    This procedure establishes requirements to administer a performance demonstration test. The test is to demonstrate that the double-shell tank inspection system (DSTIS) supplied by the contractor performs in accordance with the WHC-S-4108, Double-Shell Tank Ultrasonic Inspection Performance Specification, Rev. 2-A, January, 1995. The inspection system is intended to provide ultrasonic (UT) and visual data to determine integrity of the Westinghouse Hanford Company (WHC) site underground waste tanks. The robotic inspection system consists of the following major sub-systems (modules) and components: Mobile control center; Deployment module; Cable management assembly; Robot mechanism; Ultrasonic testing system; Visual testing system; Pneumatic system; Electrical system; and Control system.

  19. Automated Telerobotic Inspection Of Surfaces

    NASA Technical Reports Server (NTRS)

    Balaram, J.; Prasad, K. Venkatesh

    1996-01-01

    Method of automated telerobotic inspection of surfaces undergoing development. Apparatus implementing method includes video camera that scans over surfaces to be inspected, in manner of mine detector. Images of surfaces compared with reference images to detect flaws. Developed for inspecting external structures of Space Station Freedom for damage from micrometeorites and debris from prior artificial satellites. On Earth, applied to inspection for damage, missing parts, contamination, and/or corrosion on interior surfaces of pipes or exterior surfaces of bridges, towers, aircraft, and ships.

  20. Waste inspection tomography (WIT)

    SciTech Connect

    Bernardi, R.T.

    1995-10-01

    Waste Inspection Tomography (WIT) provides mobile semi-trailer mounted nondestructive examination (NDE) and assay (NDA) for nuclear waste drum characterization. WIT uses various computed tomography (CT) methods for both NDE and NDA of nuclear waste drums. Low level waste (LLW), transuranic (TRU), and mixed radioactive waste can be inspected and characterized without opening the drums. With externally transmitted x-ray NDE techniques, WIT has the ability to identify high density waste materials like heavy metals, define drum contents in two- and three-dimensional space, quantify free liquid volumes through density and x-ray attenuation coefficient discrimination, and measure drum wall thickness. With waste emitting gamma-ray NDA techniques, WIT can locate gamma emitting radioactive sources in two- and three-dimensional space, identify gamma emitting, isotopic species, identify the external activity levels of emitting gamma-ray sources, correct for waste matrix attenuation, provide internal activity approximations, and provide the data needed for waste classification as LLW or TRU.

  1. Waste inspection tomography (WIT)

    SciTech Connect

    Bernardi, R.T.; Han, K.S.

    1994-12-31

    The WIT program will provide an inspection system that offers the nuclear waste evaluator a unique combination of tools for regulatory-driven characterization of low-level waste (LLW), transuranic waste (TRU), and mixed waste drums. WIT provides nondestructive, noninvasive, and environmentally safe inspections using X-ray and gamma ray technologies, with reasonable cost and throughput. Two emission imaging techniques will be employed for characterizing materials in waste containers. The first of these is gamma emission tomography, commonly called single-photon emission computed tomography (SPECT). Rather than using an external radiation source, SPECT uses the emission of radioactive materials within the object of interest for imaging. In this case, emission from actual nuclear waste within a container will provide a three-dimensional image of the radioactive substances in the container. The second emission technique will use high-purity germanium detectors for gamma ray spectroscopy. This technique, called nondestructive assay (NDA), can identify the emitting isotopic species and strength. Work in emission tomography and assay of nuclear waste has been undertaken at Lawrence Livermore National Laboratory using a technique called Passive Tomography. Results from a process development unit are presented.

  2. Resource Guide for Regular Teachers.

    ERIC Educational Resources Information Center

    Kampert, George J.

    The resource guide for regular teachers provides policies and procedures of the Flour Bluff (Texas) school district regarding special education of handicapped students. Individual sections provide guidelines for the following areas: the referral process; individual assessment; participation on student evaluation and placement committee; special…

  3. Sparsity regularization in dynamic elastography.

    PubMed

    Honarvar, M; Sahebjavaher, R S; Salcudean, S E; Rohling, R

    2012-10-07

    We consider the inverse problem of continuum mechanics with the tissue deformation described by a mixed displacement-pressure finite element formulation. The mixed formulation is used to model nearly incompressible materials by simultaneously solving for both elasticity and pressure distributions. To improve numerical conditioning, a common solution to this problem is to use regularization to constrain the solutions of the inverse problem. We present a sparsity regularization technique that uses the discrete cosine transform to transform the elasticity and pressure fields to a sparse domain in which a smaller number of unknowns is required to represent the original field. We evaluate the approach by solving the dynamic elastography problem for synthetic data using such a mixed finite element technique, assuming time harmonic motion, and linear, isotropic and elastic behavior for the tissue. We compare our simulation results to those obtained using the more common Tikhonov regularization. We show that the sparsity regularization is less dependent on boundary conditions, less influenced by noise, requires no parameter tuning and is computationally faster. The algorithm has been tested on magnetic resonance elastography data captured from a CIRS elastography phantom with similar results as the simulation.

  4. Regularized Generalized Structured Component Analysis

    ERIC Educational Resources Information Center

    Hwang, Heungsun

    2009-01-01

    Generalized structured component analysis (GSCA) has been proposed as a component-based approach to structural equation modeling. In practice, GSCA may suffer from multi-collinearity, i.e., high correlations among exogenous variables. GSCA has yet no remedy for this problem. Thus, a regularized extension of GSCA is proposed that integrates a ridge…

  5. Regularized Generalized Structured Component Analysis

    ERIC Educational Resources Information Center

    Hwang, Heungsun

    2009-01-01

    Generalized structured component analysis (GSCA) has been proposed as a component-based approach to structural equation modeling. In practice, GSCA may suffer from multi-collinearity, i.e., high correlations among exogenous variables. GSCA has yet no remedy for this problem. Thus, a regularized extension of GSCA is proposed that integrates a ridge…

  6. Giftedness in the Regular Classroom.

    ERIC Educational Resources Information Center

    Green, Anne

    This paper presents a rationale for serving gifted students in the regular classroom and offers guidelines for recognizing students who are gifted in the seven types of intelligence proposed by Howard Gardner. Stressed is the importance of creating in the classroom a community of learners that allows all children to actively explore ideas and…

  7. Rotations of the Regular Polyhedra

    ERIC Educational Resources Information Center

    Jones, MaryClara; Soto-Johnson, Hortensia

    2006-01-01

    The study of the rotational symmetries of the regular polyhedra is important in the classroom for many reasons. Besides giving the students an opportunity to visualize in three dimensions, it is also an opportunity to relate two-dimensional and three-dimensional concepts. For example, rotations in R[superscript 2] require a point and an angle of…

  8. Regularization of Localized Degradation Processes

    DTIC Science & Technology

    1996-12-28

    order to assess the regularization properties of non-classical micropolar Cosserat continua which feature non-symmetric stress and strain tensors because...of the presence of couple-stresses and micro-curvatures. It was shown that micropolar media may only exhibit localized failure in the form of tensile

  9. 46 CFR 153.812 - Inspection for Certificate of Inspection.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Inspection for Certificate of Inspection. 153.812 Section 153.812 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SHIPS CARRYING BULK LIQUID, LIQUEFIED GAS, OR COMPRESSED GAS HAZARDOUS MATERIALS Design and...

  10. 46 CFR 176.800 - Inspection standards.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Material Inspections § 176.800 Inspection standards. (a) A vessel is inspected... acceptable to the cognizant OCMI as good marine practice. (b) In the application of inspection standards...

  11. 46 CFR 176.800 - Inspection standards.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Material Inspections § 176.800 Inspection standards. (a) A vessel is inspected... acceptable to the cognizant OCMI as good marine practice. (b) In the application of inspection standards...

  12. 46 CFR 176.800 - Inspection standards.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Material Inspections § 176.800 Inspection standards. (a) A vessel is inspected... acceptable to the cognizant OCMI as good marine practice. (b) In the application of inspection standards...

  13. 46 CFR 176.800 - Inspection standards.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Material Inspections § 176.800 Inspection standards. (a) A vessel is inspected... acceptable to the cognizant OCMI as good marine practice. (b) In the application of inspection standards...

  14. 49 CFR 396.17 - Periodic inspection.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... MAINTENANCE § 396.17 Periodic inspection. (a) Every commercial motor vehicle must be inspected as required by... least once during the preceding 12 months and documentation of such inspection is on the vehicle. The... annual inspection for vehicles under the carrier's control which are not subject to an inspection...

  15. 49 CFR 213.233 - Track inspections.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... a vehicle at a speed that allows the person making the inspection to visually inspect the track... may be used to supplement visual inspection. If a vehicle is used for visual inspection, the speed of..., otherwise, the inspection vehicle speed shall be at the sole discretion of the inspector, based on...

  16. 49 CFR 213.233 - Track inspections.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... a vehicle at a speed that allows the person making the inspection to visually inspect the track... may be used to supplement visual inspection. If a vehicle is used for visual inspection, the speed of..., otherwise, the inspection vehicle speed shall be at the sole discretion of the inspector, based on...

  17. 49 CFR 213.233 - Track inspections.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... a vehicle at a speed that allows the person making the inspection to visually inspect the track... may be used to supplement visual inspection. If a vehicle is used for visual inspection, the speed of..., otherwise, the inspection vehicle speed shall be at the sole discretion of the inspector, based on...

  18. 49 CFR 396.17 - Periodic inspection.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... MAINTENANCE § 396.17 Periodic inspection. (a) Every commercial motor vehicle must be inspected as required by... least once during the preceding 12 months and documentation of such inspection is on the vehicle. The... annual inspection for vehicles under the carrier's control which are not subject to an inspection...

  19. 49 CFR 396.17 - Periodic inspection.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... MAINTENANCE § 396.17 Periodic inspection. (a) Every commercial motor vehicle must be inspected as required by... least once during the preceding 12 months and documentation of such inspection is on the vehicle. The... annual inspection for vehicles under the carrier's control which are not subject to an inspection...

  20. 49 CFR 396.17 - Periodic inspection.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... MAINTENANCE § 396.17 Periodic inspection. (a) Every commercial motor vehicle must be inspected as required by... least once during the preceding 12 months and documentation of such inspection is on the vehicle. The... annual inspection for vehicles under the carrier's control which are not subject to an inspection...

  1. 49 CFR 213.233 - Track inspections.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... a vehicle at a speed that allows the person making the inspection to visually inspect the track... may be used to supplement visual inspection. If a vehicle is used for visual inspection, the speed of..., otherwise, the inspection vehicle speed shall be at the sole discretion of the inspector, based on...

  2. 49 CFR 213.233 - Track inspections.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... a vehicle at a speed that allows the person making the inspection to visually inspect the track... may be used to supplement visual inspection. If a vehicle is used for visual inspection, the speed of..., otherwise, the inspection vehicle speed shall be at the sole discretion of the inspector, based on...

  3. 49 CFR 213.365 - Visual inspections.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Visual inspections. 213.365 Section 213.365... Visual inspections. (a) All track shall be visually inspected in accordance with the schedule prescribed..., electrical, and other track inspection devices may be used to supplement visual inspection. If a vehicle...

  4. Temporal regularity in speech perception: Is regularity beneficial or deleterious?

    PubMed

    Geiser, Eveline; Shattuck-Hufnagel, Stefanie

    2012-04-01

    Speech rhythm has been proposed to be of crucial importance for correct speech perception and language learning. This study investigated the influence of speech rhythm in second language processing. German pseudo-sentences were presented to participants in two conditions: 'naturally regular speech rhythm' and an 'emphasized regular rhythm'. Nine expert English speakers with 3.5±1.6 years of German training repeated each sentence after hearing it once over headphones. Responses were transcribed using the International Phonetic Alphabet and analyzed for the number of correct, false and missing consonants as well as for consonant additions. The over-all number of correct reproductions of consonants did not differ between the two experimental conditions. However, speech rhythmicization significantly affected the serial position curve of correctly reproduced syllables. The results of this pilot study are consistent with the view that speech rhythm is important for speech perception.

  5. Regular languages, regular grammars and automata in splicing systems

    NASA Astrophysics Data System (ADS)

    Mohamad Jan, Nurhidaya; Fong, Wan Heng; Sarmin, Nor Haniza

    2013-04-01

    Splicing system is known as a mathematical model that initiates the connection between the study of DNA molecules and formal language theory. In splicing systems, languages called splicing languages refer to the set of double-stranded DNA molecules that may arise from an initial set of DNA molecules in the presence of restriction enzymes and ligase. In this paper, some splicing languages resulted from their respective splicing systems are shown. Since all splicing languages are regular, languages which result from the splicing systems can be further investigated using grammars and automata in the field of formal language theory. The splicing language can be written in the form of regular languages generated by grammar. Besides that, splicing systems can be accepted by automata. In this research, two restriction enzymes are used in splicing systems namely BfuCI and NcoI.

  6. Laser Safety Inspection Criteria

    SciTech Connect

    Barat, K

    2005-02-11

    A responsibility of the Laser Safety Officer (LSO) is to perform laser safety audits. The American National Standard Z136.1 Safe use of Lasers references this requirement in several sections: (1) Section 1.3.2 LSO Specific Responsibilities states under Hazard Evaluation, ''The LSO shall be responsible for hazards evaluation of laser work areas''; (2) Section 1.3.2.8, Safety Features Audits, ''The LSO shall ensure that the safety features of the laser installation facilities and laser equipment are audited periodically to assure proper operation''; and (3) Appendix D, under Survey and Inspections, it states, ''the LSO will survey by inspection, as considered necessary, all areas where laser equipment is used''. Therefore, for facilities using Class 3B and or Class 4 lasers, audits for laser safety compliance are expected to be conducted. The composition, frequency and rigueur of that inspection/audit rests in the hands of the LSO. A common practice for institutions is to develop laser audit checklists or survey forms. In many institutions, a sole Laser Safety Officer (LSO) or a number of Deputy LSO's perform these audits. For that matter, there are institutions that request users to perform a self-assessment audit. Many items on the common audit list and the associated findings are subjective because they are based on the experience and interest of the LSO or auditor in particular items on the checklist. Beam block usage is an example; to one set of eyes a particular arrangement might be completely adequate, while to another the installation may be inadequate. In order to provide more consistency, the National Ignition Facility Directorate at Lawrence Livermore National Laboratory (NIF-LLNL) has established criteria for a number of items found on the typical laser safety audit form. These criteria are distributed to laser users, and they serve two broad purposes: first, it gives the user an expectation of what will be reviewed by an auditor, and second, it is an

  7. Grain quality inspection system

    NASA Technical Reports Server (NTRS)

    Flood, C. A., Jr.; Singletow, D. P.; James, S. N.

    1979-01-01

    A review of grain quality indicators and measurement methods was conducted in order to assess the feasibility of using remote sensing technology to develop a continuous monitoring system for use during grain transfer operations. Most detection methods were found to be too slow or too expensive to be incorporated into the normal inspection procedure of a grain elevator on a continuous basis. Two indicators, moisture content and broken corn and foreign material, show potential for automation and are of an economic value. A microprocessor based system which utilizes commercially available electronic moisture meter was developed and tested. A method for automating BCFM measurement is described. A complete system description is presented along with performance test results.

  8. TPS Inspection and Repair

    NASA Technical Reports Server (NTRS)

    Parazynski, Scott

    2012-01-01

    Dr. Scott Parazynski provided a retrospective on the EVA tools and procedures efforts NASA went through in the aftermath of Columbia for the Shuttle Thermal Protection System (TPS) inspection and repair. He describes his role as the lead astronaut on this effort, and covered all of the Neutral Buoyancy Lab (NBL), KC 135 (reduced gravity aircraft), Precision Air Bearing Floor (PABF), vacuum chamber and 1 G testing that was done in order to develop the tools and techniques that were flown. Parazynski also discusses how the EVA community worked together to resolve a huge safety issue, and how his work in the spacesuit was critical to overcoming a design limitation of the Space Shuttle.

  9. TPS Inspection and Repair

    NASA Technical Reports Server (NTRS)

    Parazynski, Scott

    2012-01-01

    Dr. Scott Parazynski provided a retrospective on the EVA tools and procedures efforts NASA went through in the aftermath of Columbia for the Shuttle Thermal Protection System (TPS) inspection and repair. He describes his role as the lead astronaut on this effort, and covered all of the Neutral Buoyancy Lab (NBL), KC 135 (reduced gravity aircraft), Precision Air Bearing Floor (PABF), vacuum chamber and 1 G testing that was done in order to develop the tools and techniques that were flown. Parazynski also discusses how the EVA community worked together to resolve a huge safety issue, and how his work in the spacesuit was critical to overcoming a design limitation of the Space Shuttle.

  10. Automated fabric inspection system

    NASA Astrophysics Data System (ADS)

    Jarvis, Christine W.

    1993-10-01

    The Automatic Fabric Inspection System developed by Systronics Inc. for Clemson Apparel Research uses vision technology to acquire images of the fabric two thousand times per second. Each image-video line consisting of 2048 picture elements is analyzed by a signal processing module and a decision on defect presence and location is made. A product norm signal is first established by having the system acquire an image of an unflawed stripe of the product. The output of each picture element (pixel) is digitized to a grey scale value in the 0-255 range. Threshold levels for defects with grey scale values higher and lower than product norm can then be established and set. The system will then compare all subsequent images against the set thresholds.

  11. Inspection system calibration methods

    DOEpatents

    Deason, Vance A.; Telschow, Kenneth L.

    2004-12-28

    An inspection system calibration method includes producing two sideband signals of a first wavefront; interfering the two sideband signals in a photorefractive material, producing an output signal therefrom having a frequency and a magnitude; and producing a phase modulated operational signal having a frequency different from the output signal frequency, a magnitude, and a phase modulation amplitude. The method includes determining a ratio of the operational signal magnitude to the output signal magnitude, determining a ratio of a 1st order Bessel function of the operational signal phase modulation amplitude to a 0th order Bessel function of the operational signal phase modulation amplitude, and comparing the magnitude ratio to the Bessel function ratio.

  12. Pipe inspection and repair system

    NASA Technical Reports Server (NTRS)

    Schempf, Hagen (Inventor); Mutschler, Edward (Inventor); Chemel, Brian (Inventor); Boehmke, Scott (Inventor); Crowley, William (Inventor)

    2004-01-01

    A multi-module pipe inspection and repair device. The device includes a base module, a camera module, a sensor module, an MFL module, a brush module, a patch set/test module, and a marker module. Each of the modules may be interconnected to construct one of an inspection device, a preparation device, a marking device, and a repair device.

  13. How to Handle 'Routine' Inspections

    SciTech Connect

    Chris T. Brown

    2013-04-01

    Nondestructive examination (NDE) utilized for preservice or inservice inspection provides valuable information relating to the quality and integrity of fabricated components. This document describes the importance of detailed preparation for nondestructive examination regardless of the complexity, periodicity or routine nature of the examinations/inspections being performed.

  14. Fire Inspection Guide for Schools.

    ERIC Educational Resources Information Center

    Virginia State Corp. Commission, Richmond.

    A functional explanation of the "School Fire Prevention Inspection Form" is provided for use by local school and fire department personnel in the Virginia School Fire Prevention Inspection Program. Many helpful suggestions are made for safeguarding occupants of public school buildings from fire hazards. Items discussed are--(1) exit doors, (2)…

  15. 1990 waste tank inspection program

    SciTech Connect

    McNatt, F.G.

    1990-01-01

    Aqueous radioactive wastes from Savannah River Site separations processes are contained in large underground carbon steel tanks. Tank conditions are evaluated by inspection using periscopes, still photography, and video systems for visual imagery. Inspections made in 1990 are the subject of this report.

  16. 1990 waste tank inspection program

    SciTech Connect

    McNatt, F.G.

    1990-12-31

    Aqueous radioactive wastes from Savannah River Site separations processes are contained in large underground carbon steel tanks. Tank conditions are evaluated by inspection using periscopes, still photography, and video systems for visual imagery. Inspections made in 1990 are the subject of this report.

  17. Thermographic inspection of massive structures

    SciTech Connect

    Renshaw, Jeremy B.; Guimaraes, Maria; Scott, David B.

    2014-02-18

    Nondestructive Evaluation of concrete structures is a growing concern for the nuclear industry as well as for many other industries. As critical concrete components continue to age, the ability to assess the health and suitability for continued service has become a key consideration. In some cases, repair of these structures is difficult and expensive, while replacement is prohibitively expensive or, in some cases, not feasible. Therefore, the ability to inspect these key assets is a primary concern, especially in the nuclear industry. Due to the large size of containment buildings, cooling towers, and other large concrete assets, the ability to rapidly inspect for defects of concern is very desirable. Thermographic inspection appears to have the required ability to rapidly inspect large structures to ascertain the location and size of many of the defects of concern. This ability was demonstrated by performing a thermographic inspection of a large concrete dam in 2 days.

  18. Device for inspecting vessel surfaces

    DOEpatents

    Appel, D. Keith

    1995-01-01

    A portable, remotely-controlled inspection crawler for use along the walls of tanks, vessels, piping and the like. The crawler can be configured to use a vacuum chamber for supporting itself on the inspected surface by suction or a plurality of magnetic wheels for moving the crawler along the inspected surface. The crawler is adapted to be equipped with an ultrasonic probe for mapping the structural integrity or other characteristics of the surface being inspected. Navigation of the crawler is achieved by triangulation techniques between a signal transmitter on the crawler and a pair of microphones attached to a fixed, remote location, such as the crawler's deployment unit. The necessary communications are established between the crawler and computers external to the inspection environment for position control and storage and/or monitoring of data acquisition.

  19. Ultrasonic inspection and deployment apparatus

    DOEpatents

    Michaels, Jennifer E.; Michaels, Thomas E.; Mech, Jr., Stephen J.

    1984-01-01

    An ultrasonic inspection apparatus for the inspection of metal structures, especially installed pipes. The apparatus combines a specimen inspection element, an acoustical velocity sensing element, and a surface profiling element, all in one scanning head. A scanning head bellows contains a volume of oil above the pipe surface, serving as acoustical couplant between the scanning head and the pipe. The scanning head is mounted on a scanning truck which is mobile around a circular track surrounding the pipe. The scanning truck has sufficient motors, gears, and position encoders to allow the scanning head six degrees of motion freedom. A computer system continually monitors acoustical velocity, and uses that parameter to process surface profiling and inspection data. The profiling data is used to automatically control scanning head position and alignment and to define a coordinate system used to identify and interpret inspection data. The apparatus is suitable for highly automated, remote application in hostile environments, particularly high temperature and radiation areas.

  20. Regular Motions of Resonant Asteroids

    NASA Astrophysics Data System (ADS)

    Ferraz-Mello, S.

    1990-11-01

    RESUMEN. Se revisan resultados analiticos relativos a soluciones regulares del problema asteroidal eliptico promediados en la vecindad de una resonancia con jupiten Mencionamos Ia ley de estructura para libradores de alta excentricidad, la estabilidad de los centros de liberaci6n, las perturbaciones forzadas por la excentricidad de jupiter y las 6rbitas de corotaci6n. ABSTRAC This paper reviews analytical results concerning the regular solutions of the elliptic asteroidal problem averaged in the neighbourhood of a resonance with jupiter. We mention the law of structure for high-eccentricity librators, the stability of the libration centers, the perturbations forced by the eccentricity ofjupiter and the corotation orbits. Key words: ASThROIDS

  1. Energy functions for regularization algorithms

    NASA Technical Reports Server (NTRS)

    Delingette, H.; Hebert, M.; Ikeuchi, K.

    1991-01-01

    Regularization techniques are widely used for inverse problem solving in computer vision such as surface reconstruction, edge detection, or optical flow estimation. Energy functions used for regularization algorithms measure how smooth a curve or surface is, and to render acceptable solutions these energies must verify certain properties such as invariance with Euclidean transformations or invariance with parameterization. The notion of smoothness energy is extended here to the notion of a differential stabilizer, and it is shown that to void the systematic underestimation of undercurvature for planar curve fitting, it is necessary that circles be the curves of maximum smoothness. A set of stabilizers is proposed that meet this condition as well as invariance with rotation and parameterization.

  2. Physical model of dimensional regularization

    NASA Astrophysics Data System (ADS)

    Schonfeld, Jonathan F.

    2016-12-01

    We explicitly construct fractals of dimension 4{-}ɛ on which dimensional regularization approximates scalar-field-only quantum-field theory amplitudes. The construction does not require fractals to be Lorentz-invariant in any sense, and we argue that there probably is no Lorentz-invariant fractal of dimension greater than 2. We derive dimensional regularization's power-law screening first for fractals obtained by removing voids from 3-dimensional Euclidean space. The derivation applies techniques from elementary dielectric theory. Surprisingly, fractal geometry by itself does not guarantee the appropriate power-law behavior; boundary conditions at fractal voids also play an important role. We then extend the derivation to 4-dimensional Minkowski space. We comment on generalization to non-scalar fields, and speculate about implications for quantum gravity.

  3. Diffusion on regular random fractals

    NASA Astrophysics Data System (ADS)

    Aarão Reis, Fábio D. A.

    1996-12-01

    We study random walks on structures intermediate to statistical and deterministic fractals called regular random fractals, constructed introducing randomness in the distribution of lacunas of Sierpinski carpets. Random walks are simulated on finite stages of these fractals and the scaling properties of the mean square displacement 0305-4470/29/24/007/img1 of N-step walks are analysed. The anomalous diffusion exponents 0305-4470/29/24/007/img2 obtained are very near the estimates for the carpets with the same dimension. This result motivates a discussion on the influence of some types of lattice irregularity (random structure, dead ends, lacunas) on 0305-4470/29/24/007/img2, based on results on several fractals. We also propose to use these and other regular random fractals as models for real self-similar structures and to generalize results for statistical systems on fractals.

  4. 7 CFR 996.8 - Incoming inspection.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... STANDARDS FOR DOMESTIC AND IMPORTED PEANUTS MARKETED IN THE UNITED STATES Definitions § 996.8 Incoming inspection. Incoming inspection means the sampling, inspection, and certification of farmers stock peanuts to...

  5. 7 CFR 996.8 - Incoming inspection.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... STANDARDS FOR DOMESTIC AND IMPORTED PEANUTS MARKETED IN THE UNITED STATES Definitions § 996.8 Incoming inspection. Incoming inspection means the sampling, inspection, and certification of farmers stock peanuts to...

  6. 7 CFR 996.8 - Incoming inspection.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... STANDARDS FOR DOMESTIC AND IMPORTED PEANUTS MARKETED IN THE UNITED STATES Definitions § 996.8 Incoming inspection. Incoming inspection means the sampling, inspection, and certification of farmers stock peanuts to...

  7. 7 CFR 996.8 - Incoming inspection.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... STANDARDS FOR DOMESTIC AND IMPORTED PEANUTS MARKETED IN THE UNITED STATES Definitions § 996.8 Incoming inspection. Incoming inspection means the sampling, inspection, and certification of farmers stock peanuts to...

  8. Continental United States Military Housing Inspections Southeast

    DTIC Science & Technology

    2015-09-24

    3 Fort Gordon _________________________________________________________________________________4 Inspection Process and...45 Use of Computer- Processed Data _______________________________________________________ 46 Use...in total. Inspection Process and Criteria We inspected military housing facilities at Patrick AFB, NS Mayport, and Fort Gordon for compliance with

  9. 7 CFR 160.59 - Appeal inspections.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) NAVAL STORES REGULATIONS AND STANDARDS FOR NAVAL STORES Request Inspection by Licensed Inspectors § 160.59 Appeal inspections....

  10. 7 CFR 160.59 - Appeal inspections.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) NAVAL STORES REGULATIONS AND STANDARDS FOR NAVAL STORES Request Inspection by Licensed Inspectors § 160.59 Appeal inspections....

  11. 9 CFR 354.10 - Inspection service.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY INSPECTION AND CERTIFICATION VOLUNTARY INSPECTION OF RABBITS AND EDIBLE PRODUCTS THEREOF Basis of Service § 354.10...

  12. 7 CFR 75.38 - Lot inspections.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946 AND THE EGG PRODUCTS INSPECTION ACT (CONTINUED) REGULATIONS FOR INSPECTION...

  13. Regular connections among generalized connections

    NASA Astrophysics Data System (ADS)

    Fleischhack, Christian

    2003-09-01

    The properties of the space A of regular connections as a subset of the space Ā of generalized connections in the Ashtekar framework are studied. For every choice of compact structure group and smoothness category for the paths, it is determined whether A is dense in Ā or not. Moreover, it is proven that A has Ashtekar-Lewandowski measure zero for every non-trivial structure group and every smoothness category. The analogous results hold for gauge orbits instead of connections.

  14. On different facets of regularization theory.

    PubMed

    Chen, Zhe; Haykin, Simon

    2002-12-01

    This review provides a comprehensive understanding of regularization theory from different perspectives, emphasizing smoothness and simplicity principles. Using the tools of operator theory and Fourier analysis, it is shown that the solution of the classical Tikhonov regularization problem can be derived from the regularized functional defined by a linear differential (integral) operator in the spatial (Fourier) domain. State-of-the-art research relevant to the regularization theory is reviewed, covering Occam's razor, minimum length description, Bayesian theory, pruning algorithms, informational (entropy) theory, statistical learning theory, and equivalent regularization. The universal principle of regularization in terms of Kolmogorov complexity is discussed. Finally, some prospective studies on regularization theory and beyond are suggested.

  15. New Two-Body Regularization

    NASA Astrophysics Data System (ADS)

    Fukushima, Toshio

    2007-01-01

    We present a new scheme to regularize a three-dimensional two-body problem under perturbations. It is a combination of Sundman's time transformation and Levi-Civita's spatial coordinate transformation applied to the two-dimensional components of the position and velocity vectors in the osculating orbital plane. We adopt a coordinate triad specifying the plane as a function of the orbital angular momentum vector only. Since the magnitude of the orbital angular momentum is explicitly computed from the in-the-plane components of the position and velocity vectors, only two components of the orbital angular momentum vector are to be determined. In addition to these, we select the total energy of the two-body system and the physical time as additional components of the new variables. The equations of motion of the new variables have no singularity even when the mutual distance is extremely small, and therefore, the new variables are suitable to deal with close encounters. As a result, the number of dependent variables in the new scheme becomes eight, which is significantly smaller than the existing schemes to avoid close encounters: two less than the Kustaanheimo-Stiefel and the Bürdet-Ferrandiz regularizations, and five less than the Sperling-Bürdet/Bürdet-Heggie regularization.

  16. Regular sun exposure benefits health.

    PubMed

    van der Rhee, H J; de Vries, E; Coebergh, J W

    2016-12-01

    Since it was discovered that UV radiation was the main environmental cause of skin cancer, primary prevention programs have been started. These programs advise to avoid exposure to sunlight. However, the question arises whether sun-shunning behaviour might have an effect on general health. During the last decades new favourable associations between sunlight and disease have been discovered. There is growing observational and experimental evidence that regular exposure to sunlight contributes to the prevention of colon-, breast-, prostate cancer, non-Hodgkin lymphoma, multiple sclerosis, hypertension and diabetes. Initially, these beneficial effects were ascribed to vitamin D. Recently it became evident that immunomodulation, the formation of nitric oxide, melatonin, serotonin, and the effect of (sun)light on circadian clocks, are involved as well. In Europe (above 50 degrees north latitude), the risk of skin cancer (particularly melanoma) is mainly caused by an intermittent pattern of exposure, while regular exposure confers a relatively low risk. The available data on the negative and positive effects of sun exposure are discussed. Considering these data we hypothesize that regular sun exposure benefits health. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. 40 CFR 763.176 - Inspections.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Prohibition of the Manufacture, Importation, Processing, and Distribution in Commerce of Certain Asbestos-Containing Products; Labeling Requirements § 763.176 Inspections. The Agency will conduct inspections...

  18. Fully Employing Software Inspections Data

    NASA Technical Reports Server (NTRS)

    Shull, Forrest; Feldmann, Raimund L.; Seaman, Carolyn; Regardie, Myrna; Godfrey, Sally

    2009-01-01

    Software inspections provide a proven approach to quality assurance for software products of all kinds, including requirements, design, code, test plans, among others. Common to all inspections is the aim of finding and fixing defects as early as possible, and thereby providing cost savings by minimizing the amount of rework necessary later in the lifecycle. Measurement data, such as the number and type of found defects and the effort spent by the inspection team, provide not only direct feedback about the software product to the project team but are also valuable for process improvement activities. In this paper, we discuss NASA's use of software inspections and the rich set of data that has resulted. In particular, we present results from analysis of inspection data that illustrate the benefits of fully utilizing that data for process improvement at several levels. Examining such data across multiple inspections or projects allows team members to monitor and trigger cross project improvements. Such improvements may focus on the software development processes of the whole organization as well as improvements to the applied inspection process itself.

  19. Automated fuel pellet inspection system

    NASA Astrophysics Data System (ADS)

    Lichauer, John C.; Zana, Larry J.

    1992-11-01

    In the nuclear fuels industry, a great deal of effort goes into ensuring that quality materials are produced. Of these materials, none receives more attention than the uranium-oxide nuclear fuel pellets. These cylindrically shaped pellets (approx. 1/2 inch L X 1/2 inch D) are carefully produced and then meticulously inspected for various defects (e.g., cracks, chips, etc.). The inspection process is designed to remove any defective pellets from each lot, assuring the end user a reliable, predictable, and safe product. The current (manual) inspection process is laborious and subjective in nature. The inspector also receives prolonged exposure to low-level radiation. For these reasons, automated inspection of nuclear fuel pellets has long been a goal of the industry. However, it is not a simple task, due to the many material handling and image processing challenges required to inspect pellets at production rates (greater than five per second). This paper describes an automated nuclear fuel pellet inspection system that has successfully met these challenges. Built around a set of modular, high-speed, pipelined image processing hardware, it inspects pellets at rates of up to seven pellets per second. Recent tests have shown better than 97% detection rates with less than 2% false reject rates. Image processing algorithms and solutions to design challenges are described.

  20. Visual inspection for CTBT verification

    SciTech Connect

    Hawkins, W.; Wohletz, K.

    1997-03-01

    On-site visual inspection will play an essential role in future Comprehensive Test Ban Treaty (CTBT) verification. Although seismic and remote sensing techniques are the best understood and most developed methods for detection of evasive testing of nuclear weapons, visual inspection can greatly augment the certainty and detail of understanding provided by these more traditional methods. Not only can visual inspection offer ``ground truth`` in cases of suspected nuclear testing, but it also can provide accurate source location and testing media properties necessary for detailed analysis of seismic records. For testing in violation of the CTBT, an offending party may attempt to conceal the test, which most likely will be achieved by underground burial. While such concealment may not prevent seismic detection, evidence of test deployment, location, and yield can be disguised. In this light, if a suspicious event is detected by seismic or other remote methods, visual inspection of the event area is necessary to document any evidence that might support a claim of nuclear testing and provide data needed to further interpret seismic records and guide further investigations. However, the methods for visual inspection are not widely known nor appreciated, and experience is presently limited. Visual inspection can be achieved by simple, non-intrusive means, primarily geological in nature, and it is the purpose of this report to describe the considerations, procedures, and equipment required to field such an inspection.

  1. Ultrasonic Inspection Near Small Bores

    NASA Technical Reports Server (NTRS)

    Parent, R. G.

    1986-01-01

    Portable ultrasonic probe makes it possible to inspect for hidden cracks near insides of narrow tubes. Using pulse-echo technique, instrument detects cracks as small as 0.015-in. (0.38-mm) deep. Used for nondestructive inspection of other hard-to-reach places where conventional large transducers will not fit or where difficult to apply coupling liquid for contact ultrasonic testing. Inspects bore of tubelike fitting. Instrument makes it unnecessary to disassemble fitting to check for cracks. Precise orientation of transducer with respect to part not necessary for detecting cracks.

  2. Evaluation of Microencapsulated Penetrant Inspection.

    DTIC Science & Technology

    1980-12-01

    AD-A9b 826 GENERAL ELECTRIC CO CINCINNATI OH AIRCRAFT ENGINE GROUP F/6 IA/2ADG EVALUATION OF MICROENCAPSULATED PENETRANT INSPECTION.(U) DEC 80 J M...4156 ADA096826 EVALUATION OF MICROENCAPSULATED PENETRANT INSPECTION i :I J.M. Portaz Aircraft Engine Group General Electric Company Cincinnati, Ohio... Microencapsulated Penetrant 5 7riJF-Iehica17 = Inspection p un May@84 -1 ---- --- ---- 19AMFGK657j7 7. AiJTHOR(s) nVCWRACT OR GRANT m 𔃻 " JO J.M./Portaz

  3. Procedures for precap visual inspection

    NASA Technical Reports Server (NTRS)

    1984-01-01

    Screening procedures for the final precap visual inspection of microcircuits used in electronic system components are described as an aid in training personnel unfamiliar with microcircuits. Processing techniques used in industry for the manufacture of monolithic and hybrid components are presented and imperfections that may be encountered during this inspection are discussed. Problem areas such as scratches, voids, adhesions, and wire bonding are illustrated by photomicrographs. This guide can serve as an effective tool in training personnel to perform precap visual inspections efficiently and reliably.

  4. F Reactor Inspection

    ScienceCinema

    Grindstaff, Keith; Hathaway, Boyd; Wilson, Mike

    2016-07-12

    Workers from Mission Support Alliance, LLC., removed the welds around the steel door of the F Reactor before stepping inside the reactor to complete its periodic inspection. This is the first time the Department of Energy (DOE) has had the reactor open since 2008. The F Reactor is one of nine reactors along the Columbia River at the Department's Hanford Site in southeastern Washington State, where environmental cleanup has been ongoing since 1989. As part of the Tri-Party Agreement, the Department completes surveillance and maintenance activities of cocooned reactors periodically to evaluate the structural integrity of the safe storage enclosure and to ensure confinement of any remaining hazardous materials. "This entry marks a transition of sorts because the Hanford Long-Term Stewardship Program, for the first time, was responsible for conducting the entry and surveillance and maintenance activities," said Keith Grindstaff, Energy Department Long-Term Stewardship Program Manager. "As the River Corridor cleanup work is completed and transitioned to long-term stewardship, our program will manage any on-going requirements."

  5. F Reactor Inspection

    SciTech Connect

    Grindstaff, Keith; Hathaway, Boyd; Wilson, Mike

    2014-10-29

    Workers from Mission Support Alliance, LLC., removed the welds around the steel door of the F Reactor before stepping inside the reactor to complete its periodic inspection. This is the first time the Department of Energy (DOE) has had the reactor open since 2008. The F Reactor is one of nine reactors along the Columbia River at the Department's Hanford Site in southeastern Washington State, where environmental cleanup has been ongoing since 1989. As part of the Tri-Party Agreement, the Department completes surveillance and maintenance activities of cocooned reactors periodically to evaluate the structural integrity of the safe storage enclosure and to ensure confinement of any remaining hazardous materials. "This entry marks a transition of sorts because the Hanford Long-Term Stewardship Program, for the first time, was responsible for conducting the entry and surveillance and maintenance activities," said Keith Grindstaff, Energy Department Long-Term Stewardship Program Manager. "As the River Corridor cleanup work is completed and transitioned to long-term stewardship, our program will manage any on-going requirements."

  6. Inspecting Engineering Samples

    NASA Image and Video Library

    2017-09-27

    Goddard's Ritsko Wins 2011 SAVE Award The winner of the 2011 SAVE Award is Matthew Ritsko, a Goddard financial manager. His tool lending library would track and enable sharing of expensive space-flight tools and hardware after projects no longer need them. This set of images represents the types of tools used at NASA. To read more go to: www.nasa.gov/topics/people/features/ritsko-save.html Dr. Doug Rabin (Code 671) and PI La Vida Cooper (Code 564) inspect engineering samples of the HAS-2 imager which will be tested and readout using a custom ASIC with a 16-bit ADC (analog to digital converter) and CDS (correlated double sampling) circuit designed by the Code 564 ASIC group as a part of an FY10 IRAD. The purpose of the IRAD was to develop and high resolution digitizer for Heliophysics applications such as imaging. Future goals for the collaboration include characterization testing and eventually a sounding rocket flight of the integrated system. *ASIC= Application Specific Integrated Circuit NASA/GSFC/Chris Gunn

  7. Diversity in underwater inspection

    SciTech Connect

    Goldberg, L.

    1996-03-01

    Underwater nondestructive testing (NDT) of deepwater structures provides a diverse, hostile, and challenging means to implement NDT. Given a warm, shallow water with good visibility, working underwater approaches the category of ``I get paid for this.`` This environment allows for identical reliability as ``topside`` NDT. Underwater visual, magnetic particle, and ultrasonic testing have been in place since the early 1980s, with equipment modified for submergence and closely resembling topside NDT tools. However, deepwater structures represent the most unique of NDT considerations. In the Gulf of Mexico, there are approximately 15 fixed structures installed at a depth of 243--400 m. This article describes safety, technical, and commercial issues relating to inspecting deepwater structures and focuses especially on a comparison of remote operated vehicles (ROVs) and atmospheric diving suits (ADSs). Deepwater structures have excellent records of structural integrity with an extremely low incidence of corrosion or fatigue cracking problems. The primary reason for developing deepwater NDT capabilities is contingency for damage during installation impact damage from dropped objects. There are three means used for underwater NDT: diving, atmospheric diving suits (ADSs), and remotely operated vehicles (ROVs).

  8. Identification and sorting of regular textures according to their similarity

    NASA Astrophysics Data System (ADS)

    Hernández Mesa, Pilar; Anastasiadis, Johannes; Puente León, Fernando

    2015-05-01

    Regardless whether mosaics, material surfaces or skin surfaces are inspected their texture plays an important role. Texture is a property which is hard to describe using words but it can easily be described in pictures. Furthermore, a huge amount of digital images containing a visual description of textures already exists. However, this information becomes useless if there are no appropriate methods to browse the data. In addition, depending on the given task some properties like scale, rotation or intensity invariance are desired. In this paper we propose to analyze texture images according to their characteristic pattern. First a classification approach is proposed to separate regular from non-regular textures. The second stage will focus on regular textures suggesting a method to sort them according to their similarity. Different features will be extracted from the texture in order to describe its scale, orientation, texel and the texel's relative position. Depending on the desired invariance of the visual characteristics (like the texture's scale or the texel's form invariance) the comparison of the features between images will be weighted and combined to define the degree of similarity between them. Tuning the weighting parameters allows this search algorithm to be easily adapted to the requirements of the desired task. Not only the total invariance of desired parameters can be adjusted, the weighting of the parameters may also be modified to adapt to an application-specific type of similarity. This search method has been evaluated using different textures and similarity criteria achieving very promising results.

  9. Knowledge and regularity in planning

    NASA Technical Reports Server (NTRS)

    Allen, John A.; Langley, Pat; Matwin, Stan

    1992-01-01

    The field of planning has focused on several methods of using domain-specific knowledge. The three most common methods, use of search control, use of macro-operators, and analogy, are part of a continuum of techniques differing in the amount of reused plan information. This paper describes TALUS, a planner that exploits this continuum, and is used for comparing the relative utility of these methods. We present results showing how search control, macro-operators, and analogy are affected by domain regularity and the amount of stored knowledge.

  10. Comparison of the prognostic value of the 6th and 7th editions of the Union for International Cancer Control TNM staging system in patients with lower esophageal cancer undergoing neoadjuvant chemotherapy followed by surgery.

    PubMed

    Mehta, S P; Jose, P; Mirza, A; Pritchard, S A; Hayden, J D; Grabsch, H I

    2013-01-01

    Carcinoma of the esophagus is classified according to the Union for International Cancer Control (UICC) TNM staging system. The 7th edition of the UICC TNM staging system was published in 2009. This is the first study to compare the prognostic value of the TNM 6th and 7th editions in patients with esophageal carcinoma treated with chemotherapy followed by surgery. Two hundred forty-three patients with esophageal carcinoma were retrospectively selected from two referral centers. All patients received chemotherapy before surgery. Histopathologic data from the resection specimens were retrieved and restaged according to the TNM 7th edition. Disease-specific survival curves were plotted for depth of tumor invasion (ypT), lymph node status (ypN), and ypTNM stage and then compared. Median follow-up after surgery was 2.5 years (range 0.2-9 years). Survival analysis using the log-rank method revealed that there was a significant difference in survival between ypT4 disease and ypT3 disease (P= 0.003), but no difference between ypT0, ypT1, ypT2, and ypT3 categories irrespective of TNM edition used. Survival probability was significantly different between ypN0 and ypN1 (P= 0.001 for TNM 6th and 7th edition), as well as ypN2 and ypN3 (TNM 7th edition, P= 0.004), but not between ypN1 and ypN2 (TNM 7th edition, P= 0.89). Neither the TNM 6th nor 7th edition T staging provides accurate survival probability stratification. However, the advantage of the 7th edition is the introduction of a third tier in survival stratification for patients with nodal involvement. © 2012 Copyright the Authors. Journal compilation © 2012, Wiley Periodicals, Inc. and the International Society for Diseases of the Esophagus.

  11. Ultrasonic Inspection Of Thick Sections

    NASA Technical Reports Server (NTRS)

    Friant, C. L.; Djordjevic, B. B.; O'Keefe, C. V.; Ferrell, W.; Klutz, T.

    1993-01-01

    Ultrasonics used to inspect large, relatively thick vessels for hidden defects. Report based on experiments in through-the-thickness transmission of ultrasonic waves in both steel and filament-wound composite cases of solid-fuel rocket motors.

  12. Underwater welding, cutting and inspection

    SciTech Connect

    Tsai, C.L. . Ohio Underwater Welding Center)

    1995-02-01

    Underwater welding, cutting and inspection of offshore, inland waterway and port facilities are becoming a requirement for both military and industrial communities, as maintenance and repair costs continue to escalate, and as many of the facilities are in operation well beyond their intended design life. In nuclear applications, underwater welding, cutting and inspection for repair and modification of irradiated nuclear power plant components are also a requirement. This article summarizes recent developments in this emerging underwater technology.

  13. MELFI-3 Cold Box inspection

    NASA Image and Video Library

    2015-03-13

    ISS043e000724 (03/13/2015) --- ESA (European Space Agency) astronaut Samantha Cristoforetti, Expedition 43 flight engineer works daily on science and maintenance duties on board the International Space Station. She is inspecting the Minus Eighty-degree Laboratory Freezer called by the shorter title "MELFI-3 Cold Box inspection". Astronauts are trained for long periods at the Johnson Space Center and in Russia before their missions in space begin so that they are fully trained for these complex duties.

  14. Surface inspection: Research and development

    NASA Technical Reports Server (NTRS)

    Batchelder, J. S.

    1987-01-01

    Surface inspection techniques are used for process learning, quality verification, and postmortem analysis in manufacturing for a spectrum of disciplines. First, trends in surface analysis are summarized for integrated circuits, high density interconnection boards, and magnetic disks, emphasizing on-line applications as opposed to off-line or development techniques. Then, a closer look is taken at microcontamination detection from both a patterned defect and a particulate inspection point of view.

  15. Gravity Probe B Inspection

    NASA Technical Reports Server (NTRS)

    2000-01-01

    The space vehicle Gravity Probe B (GP-B) is the relativity experiment developed at Stanford University to test two extraordinary predictions of Albert Einstein's general theory of relativity. The experiment will measure, very precisely, the expected tiny changes in the direction of the spin axes of four gyroscopes contained in an Earth-orbiting satellite at a 400-mile altitude. So free are the gyroscopes from disturbance that they will provide an almost perfect space-time reference system. They will measure how space and time are very slightly warped by the presence of the Earth, and, more profoundly, how the Earth's rotation very slightly drags space-time around with it. These effects, though small for the Earth, have far-reaching implications for the nature of matter and the structure of the Universe. GP-B is among the most thoroughly researched programs ever undertaken by NASA. This is the story of a scientific quest in which physicists and engineers have collaborated closely over many years. Inspired by their quest, they have invented a whole range of technologies that are already enlivening other branches of science and engineering. In this photograph, engineer Gary Reynolds is inspecting the inside of the probe neck during probe thermal repairs. GP-B is scheduled for launch in April 2004 and managed for NASA by the Marshall Space Flight Center. Development of the GP-B is the responsibility of Stanford University along with major subcontractor Lockheed Martin Corporation. (Image credit to Russ Leese, Gravity Probe B, Stanford University)

  16. Advanced algorithms for radiographic material discrimination and inspection system design

    SciTech Connect

    Gilbert, Andrew J.; McDonald, Benjamin S.; Deinert, Mark R.

    2016-10-01

    X-ray and neutron radiography are powerful tools for non-invasively inspecting the interior of objects. Materials can be discriminated by noting how the radiographic signal changes with variations in the input spectrum or inspection mode. However, current methods are limited in their ability to differentiate when multiple materials are present, especially within large and complex objects. With X-ray radiography, the inability to distinguish materials of a similar atomic number is especially problematic. To overcome these critical limitations, we augmented our existing inverse problem framework with two important expansions: 1) adapting the previous methodology for use with multi-modal radiography and energy-integrating detectors, and 2) applying the Cramer-Rao lower bound to select an optimal set of inspection modes for a given application a priori. Adding these expanded capabilities to our algorithmic framework with adaptive regularization, we observed improved discrimination between high-Z materials, specifically plutonium and tungsten. The combined system can estimate plutonium mass within our simulated system to within 1%. Three types of inspection modes were modeled: multi-endpoint X-ray radiography alone; in combination with neutron radiography using deuterium-deuterium (DD); or in combination with neutron radiography using deuterium-tritium (DT) sources.

  17. 10 CFR 76.121 - Inspections.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Inspections. 76.121 Section 76.121 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Reports and Inspections § 76.121 Inspections. (a) The Corporation shall afford to the Commission opportunity to inspect the premises and...

  18. 10 CFR 76.121 - Inspections.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Inspections. 76.121 Section 76.121 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Reports and Inspections § 76.121 Inspections. (a) The Corporation shall afford to the Commission opportunity to inspect the premises and...

  19. 10 CFR 76.121 - Inspections.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 2 2014-01-01 2014-01-01 false Inspections. 76.121 Section 76.121 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Reports and Inspections § 76.121 Inspections. (a) The Corporation shall afford to the Commission opportunity to inspect the premises and...

  20. 10 CFR 76.121 - Inspections.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Inspections. 76.121 Section 76.121 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Reports and Inspections § 76.121 Inspections. (a) The Corporation shall afford to the Commission opportunity to inspect the premises and...

  1. 10 CFR 76.121 - Inspections.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Inspections. 76.121 Section 76.121 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Reports and Inspections § 76.121 Inspections. (a) The Corporation shall afford to the Commission opportunity to inspect the premises and...

  2. 23 CFR 650.311 - Inspection frequency.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 23 Highways 1 2010-04-01 2010-04-01 false Inspection frequency. 650.311 Section 650.311 Highways..., STRUCTURES, AND HYDRAULICS National Bridge Inspection Standards § 650.311 Inspection frequency. (a) Routine... level and frequency to which these bridges are inspected considering such factors as age, traffic...

  3. 23 CFR 650.311 - Inspection frequency.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 23 Highways 1 2012-04-01 2012-04-01 false Inspection frequency. 650.311 Section 650.311 Highways..., STRUCTURES, AND HYDRAULICS National Bridge Inspection Standards § 650.311 Inspection frequency. (a) Routine... level and frequency to which these bridges are inspected considering such factors as age, traffic...

  4. 23 CFR 650.311 - Inspection frequency.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 23 Highways 1 2013-04-01 2013-04-01 false Inspection frequency. 650.311 Section 650.311 Highways..., STRUCTURES, AND HYDRAULICS National Bridge Inspection Standards § 650.311 Inspection frequency. (a) Routine... level and frequency to which these bridges are inspected considering such factors as age, traffic...

  5. 23 CFR 650.311 - Inspection frequency.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 23 Highways 1 2011-04-01 2011-04-01 false Inspection frequency. 650.311 Section 650.311 Highways..., STRUCTURES, AND HYDRAULICS National Bridge Inspection Standards § 650.311 Inspection frequency. (a) Routine... level and frequency to which these bridges are inspected considering such factors as age, traffic...

  6. 23 CFR 650.311 - Inspection frequency.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 23 Highways 1 2014-04-01 2014-04-01 false Inspection frequency. 650.311 Section 650.311 Highways..., STRUCTURES, AND HYDRAULICS National Bridge Inspection Standards § 650.311 Inspection frequency. (a) Routine... level and frequency to which these bridges are inspected considering such factors as age, traffic...

  7. 10 CFR 60.75 - Inspections.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 2 2014-01-01 2014-01-01 false Inspections. 60.75 Section 60.75 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES Records, Reports, Tests, and Inspections § 60.75 Inspections. (a) DOE shall allow the Commission to inspect the...

  8. 10 CFR 60.75 - Inspections.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Inspections. 60.75 Section 60.75 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES Records, Reports, Tests, and Inspections § 60.75 Inspections. (a) DOE shall allow the Commission to inspect the...

  9. 10 CFR 60.75 - Inspections.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Inspections. 60.75 Section 60.75 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES Records, Reports, Tests, and Inspections § 60.75 Inspections. (a) DOE shall allow the Commission to inspect the...

  10. 10 CFR 60.75 - Inspections.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Inspections. 60.75 Section 60.75 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES Records, Reports, Tests, and Inspections § 60.75 Inspections. (a) DOE shall allow the Commission to inspect the...

  11. 10 CFR 60.75 - Inspections.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Inspections. 60.75 Section 60.75 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) DISPOSAL OF HIGH-LEVEL RADIOACTIVE WASTES IN GEOLOGIC REPOSITORIES Records, Reports, Tests, and Inspections § 60.75 Inspections. (a) DOE shall allow the Commission to inspect the...

  12. Introduce Construction Technology through Home Inspection

    ERIC Educational Resources Information Center

    Wiggins, Enrique R.

    2007-01-01

    Introducing technology education students to the field of home inspection gives them a great opportunity to learn about and apply construction technology content. In working with his 8th-grade students, the author covers the purpose of a home inspection, the dynamic of home inspections, the process involved in inspecting schools and homes and…

  13. 46 CFR 115.800 - Inspection standards.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150... Inspections § 115.800 Inspection standards. (a) A vessel is inspected for compliance with the standards... marine practice. (b) In the application of inspection standards due consideration must be given to...

  14. 46 CFR 115.800 - Inspection standards.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150... Inspections § 115.800 Inspection standards. (a) A vessel is inspected for compliance with the standards... marine practice. (b) In the application of inspection standards due consideration must be given to...

  15. 46 CFR 115.800 - Inspection standards.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150... Inspections § 115.800 Inspection standards. (a) A vessel is inspected for compliance with the standards... marine practice. (b) In the application of inspection standards due consideration must be given to...

  16. 46 CFR 115.800 - Inspection standards.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150... Inspections § 115.800 Inspection standards. (a) A vessel is inspected for compliance with the standards... marine practice. (b) In the application of inspection standards due consideration must be given to...

  17. 46 CFR 176.800 - Inspection standards.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... recognized safety associations may be used as guides in the inspection of vessels when such standards do not... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Material Inspections § 176.800 Inspection standards. (a) A vessel is...

  18. 46 CFR 169.226 - Periodic inspection.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... periodic inspection within 3 months before or after the second or third anniversary of the date of your vessel's Certificate of Inspection. This periodic inspection will take the place of an annual inspection... a time and place which he or she approves. No written application is required. (c) The scope of...

  19. Introduce Construction Technology through Home Inspection

    ERIC Educational Resources Information Center

    Wiggins, Enrique R.

    2007-01-01

    Introducing technology education students to the field of home inspection gives them a great opportunity to learn about and apply construction technology content. In working with his 8th-grade students, the author covers the purpose of a home inspection, the dynamic of home inspections, the process involved in inspecting schools and homes and…

  20. 46 CFR 107.269 - Annual inspection.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Annual inspection. 107.269 Section 107.269 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.269 Annual inspection. (a) Your mobile offshore drilling unit...

  1. 46 CFR 107.271 - Inspection: Alterations.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Inspection: Alterations. 107.271 Section 107.271 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.271 Inspection: Alterations. After plans are...

  2. 46 CFR 107.271 - Inspection: Alterations.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Inspection: Alterations. 107.271 Section 107.271 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.271 Inspection: Alterations. After plans are...

  3. 46 CFR 107.275 - Other inspections.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Other inspections. 107.275 Section 107.275 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.275 Other inspections. When the Coast Guard receives the report...

  4. 46 CFR 107.270 - Periodic inspection.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Periodic inspection. 107.270 Section 107.270 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.270 Periodic inspection. (a) Your vessel must undergo a...

  5. 46 CFR 107.269 - Annual inspection.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Annual inspection. 107.269 Section 107.269 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.269 Annual inspection. (a) Your mobile offshore drilling unit...

  6. 46 CFR 107.270 - Periodic inspection.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Periodic inspection. 107.270 Section 107.270 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.270 Periodic inspection. (a) Your vessel must undergo a...

  7. 46 CFR 107.275 - Other inspections.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Other inspections. 107.275 Section 107.275 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.275 Other inspections. When the Coast Guard receives the report...

  8. 46 CFR 107.269 - Annual inspection.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Annual inspection. 107.269 Section 107.269 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.269 Annual inspection. (a) Your mobile offshore drilling unit...

  9. 46 CFR 107.270 - Periodic inspection.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Periodic inspection. 107.270 Section 107.270 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.270 Periodic inspection. (a) Your vessel must undergo a...

  10. 46 CFR 107.269 - Annual inspection.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Annual inspection. 107.269 Section 107.269 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.269 Annual inspection. (a) Your mobile offshore drilling unit...

  11. 46 CFR 107.271 - Inspection: Alterations.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Inspection: Alterations. 107.271 Section 107.271 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.271 Inspection: Alterations. After plans are...

  12. 46 CFR 107.271 - Inspection: Alterations.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Inspection: Alterations. 107.271 Section 107.271 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.271 Inspection: Alterations. After plans are...

  13. 46 CFR 107.270 - Periodic inspection.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Periodic inspection. 107.270 Section 107.270 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.270 Periodic inspection. (a) Your vessel must undergo a...

  14. 46 CFR 107.275 - Other inspections.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Other inspections. 107.275 Section 107.275 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.275 Other inspections. When the Coast Guard receives the report...

  15. 46 CFR 107.275 - Other inspections.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Other inspections. 107.275 Section 107.275 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.275 Other inspections. When the Coast Guard receives the report...

  16. 46 CFR 107.269 - Annual inspection.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Annual inspection. 107.269 Section 107.269 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.269 Annual inspection. (a) Your mobile offshore drilling unit...

  17. 46 CFR 107.270 - Periodic inspection.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Periodic inspection. 107.270 Section 107.270 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.270 Periodic inspection. (a) Your vessel must undergo a...

  18. 46 CFR 107.271 - Inspection: Alterations.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Inspection: Alterations. 107.271 Section 107.271 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS INSPECTION AND CERTIFICATION Inspection and Certification § 107.271 Inspection: Alterations. After plans are...

  19. 49 CFR 230.13 - Daily inspection.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS General General Inspection... inspect each steam locomotive and its tender each day that they are offered for use to determine that they... paragraph (a) of this section, inspect the steam locomotive and its tender and appurtenances to ensure that...

  20. 49 CFR 230.13 - Daily inspection.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS General General Inspection... inspect each steam locomotive and its tender each day that they are offered for use to determine that they... paragraph (a) of this section, inspect the steam locomotive and its tender and appurtenances to ensure that...

  1. 49 CFR 230.13 - Daily inspection.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS General General Inspection... inspect each steam locomotive and its tender each day that they are offered for use to determine that they... paragraph (a) of this section, inspect the steam locomotive and its tender and appurtenances to ensure that...

  2. 36 CFR 64.14 - Project inspections.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Project inspections. 64.14... Project inspections. All State and local projects will receive a final inspection by the Bureau. Final... as deemed necessary by the Bureau. Preapproval inspections will also be conducted prior to project...

  3. 36 CFR 64.14 - Project inspections.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 36 Parks, Forests, and Public Property 1 2014-07-01 2014-07-01 false Project inspections. 64.14... Project inspections. All State and local projects will receive a final inspection by the Bureau. Final... as deemed necessary by the Bureau. Preapproval inspections will also be conducted prior to project...

  4. 36 CFR 64.14 - Project inspections.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 36 Parks, Forests, and Public Property 1 2012-07-01 2012-07-01 false Project inspections. 64.14... Project inspections. All State and local projects will receive a final inspection by the Bureau. Final... as deemed necessary by the Bureau. Preapproval inspections will also be conducted prior to project...

  5. 36 CFR 64.14 - Project inspections.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 36 Parks, Forests, and Public Property 1 2011-07-01 2011-07-01 false Project inspections. 64.14... Project inspections. All State and local projects will receive a final inspection by the Bureau. Final... as deemed necessary by the Bureau. Preapproval inspections will also be conducted prior to project...

  6. 49 CFR 213.365 - Visual inspections.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ..., electrical, and other track inspection devices may be used to supplement visual inspection. If a vehicle is used for visual inspection, the speed of the vehicle may not be more than 5 miles per hour when passing over track crossings and turnouts, otherwise, the inspection vehicle speed shall be at the...

  7. 49 CFR 213.365 - Visual inspections.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ..., electrical, and other track inspection devices may be used to supplement visual inspection. If a vehicle is used for visual inspection, the speed of the vehicle may not be more than 5 miles per hour when passing over track crossings and turnouts, otherwise, the inspection vehicle speed shall be at the...

  8. 49 CFR 213.365 - Visual inspections.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ..., electrical, and other track inspection devices may be used to supplement visual inspection. If a vehicle is used for visual inspection, the speed of the vehicle may not be more than 5 miles per hour when passing over track crossings and turnouts, otherwise, the inspection vehicle speed shall be at the...

  9. Proceedings: EPRI Second Phased Array Inspection Seminar

    SciTech Connect

    2001-11-01

    The Second EPRI Phased Array Inspection Seminar focused on industrial applications of phased array technology that have been achieved to date or are planned for the near future. Presentations were made by developers of inspection techniques, inspection services vendors, and utility personnel who have performed inspections using arrays.

  10. 49 CFR 237.105 - Special inspections.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Special inspections. 237.105 Section 237.105..., DEPARTMENT OF TRANSPORTATION BRIDGE SAFETY STANDARDS Bridge Inspection § 237.105 Special inspections. (a... inspection of any bridge that might have been damaged by a natural or accidental event, including but...

  11. 49 CFR 237.105 - Special inspections.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Special inspections. 237.105 Section 237.105..., DEPARTMENT OF TRANSPORTATION BRIDGE SAFETY STANDARDS Bridge Inspection § 237.105 Special inspections. (a... inspection of any bridge that might have been damaged by a natural or accidental event, including but...

  12. 49 CFR 237.105 - Special inspections.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Special inspections. 237.105 Section 237.105..., DEPARTMENT OF TRANSPORTATION BRIDGE SAFETY STANDARDS Bridge Inspection § 237.105 Special inspections. (a... inspection of any bridge that might have been damaged by a natural or accidental event, including but...

  13. 49 CFR 237.105 - Special inspections.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Special inspections. 237.105 Section 237.105..., DEPARTMENT OF TRANSPORTATION BRIDGE SAFETY STANDARDS Bridge Inspection § 237.105 Special inspections. (a... inspection of any bridge that might have been damaged by a natural or accidental event, including but...

  14. 49 CFR 230.13 - Daily inspection.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS General General Inspection... inspect each steam locomotive and its tender each day that they are offered for use to determine that they... paragraph (a) of this section, inspect the steam locomotive and its tender and appurtenances to ensure that...

  15. 49 CFR 230.13 - Daily inspection.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS General General Inspection... inspect each steam locomotive and its tender each day that they are offered for use to determine that they... paragraph (a) of this section, inspect the steam locomotive and its tender and appurtenances to ensure that...

  16. A study of defects on EUV mask using blank inspection, patterned mask inspection, and wafer inspection

    SciTech Connect

    Huh, S.; Ren, L.; Chan, D.; Wurm, S.; Goldberg, K. A.; Mochi, I.; Nakajima, T.; Kishimoto, M.; Ahn, B.; Kang, I.; Park, J.-O.; Cho, K.; Han, S.-I.; Laursen, T.

    2010-03-12

    The availability of defect-free masks remains one of the key challenges for inserting extreme ultraviolet lithography (EUVL) into high volume manufacturing. yet link data is available for understanding native defects on real masks. In this paper, a full-field EUV mask is fabricated to investigate the printability of various defects on the mask. The printability of defects and identification of their source from mask fabrication to handling were studied using wafer inspection. The printable blank defect density excluding particles and patterns is 0.63 cm{sup 2}. Mask inspection is shown to have better sensitivity than wafer inspection. The sensitivity of wafer inspection must be improved using through-focus analysis and a different wafer stack.

  17. ROBOTIC TANK INSPECTION END EFFECTOR

    SciTech Connect

    Rachel Landry

    1999-10-01

    The objective of this contract between Oceaneering Space Systems (OSS) and the Department of Energy (DOE) was to provide a tool for the DOE to inspect the inside tank walls of underground radioactive waste storage tanks in their tank farms. Some of these tanks are suspected to have leaks, but the harsh nature of the environment within the tanks precludes human inspection of tank walls. As a result of these conditions only a few inspection methods can fulfill this task. Of the methods available, OSS chose to pursue Alternating Current Field Measurement (ACFM), because it does not require clean surfaces for inspection, nor any contact with the Surface being inspected, and introduces no extra by-products in the inspection process (no coupling fluids or residues are left behind). The tool produced by OSS is the Robotic Tank Inspection End Effector (RTIEE), which is initially deployed on the tip of the Light Duty Utility Arm (LDUA). The RTEE combines ACFM with a color video camera for both electromagnetic and visual inspection The complete package consists of an end effector, its corresponding electronics and software, and a user's manual to guide the operator through an inspection. The system has both coarse and fine inspection modes and allows the user to catalog defects and suspected areas of leakage in a database for further examination, which may lead to emptying the tank for repair, decommissioning, etc.. The following is an updated report to OSS document OSS-21100-7002, which was submitted in 1995. During the course of the contract, two related subtasks arose, the Wall and Coating Thickness Sensor and the Vacuum Scarifying and Sampling Tool Assembly. The first of these subtasks was intended to evaluate the corrosion and wall thinning of 55-gallon steel drums. The second was retrieved and characterized the waste material trapped inside the annulus region of the underground tanks on the DOE's tank farms. While these subtasks were derived from the original intent of

  18. MAXIMAL POINTS OF A REGULAR TRUTH FUNCTION

    DTIC Science & Technology

    Every canonical linearly separable truth function is a regular function, but not every regular truth function is linearly separable. The most...promising method of determining which of the regular truth functions are linearly separable r quires finding their maximal and minimal points. In this...report is developed a quick, systematic method of finding the maximal points of any regular truth function in terms of its arithmetic invariants. (Author)

  19. System-dependent earthquake inspection procedures at Paranal Observatory

    NASA Astrophysics Data System (ADS)

    Osorio, J.; Ramirez, A.

    2016-07-01

    Paranal Observatory is located near Antofagasta city, northern Chile, one of the most seismic regions in the world. Telescopes and scientific instruments are permanently exposed to the risk of damage caused by earthquake events, ranging from optical misalignment to complete cease of operations. A seismic monitor is installed on the site, providing real-time data to make rapid post-earthquake assessments of expected damage and determine the areas, type and level of inspections to be carried out before continuing with the regular operations. With more than ten years of seismic data and its correlation with reported issues, we show that the inspection and recovery strategy can be defined taking into account the characteristics of the seismic event and according to system-dependent criteria.

  20. EDITORIAL: Proceedings of the 6th Edoardo Amaldi Conference on Gravitational Waves, Bankoku Shinryoukan, Okinawa, Japan, 20-24 June 2005 Proceedings of the 6th Edoardo Amaldi Conference on Gravitational Waves, Bankoku Shinryoukan, Okinawa, Japan, 20-24 June 2005

    NASA Astrophysics Data System (ADS)

    Mio, N.

    2006-04-01

    This issue is published as the Proceedings of the 6th Edoardo Amaldi Conference on Gravitational Waves, held on 20-24 June 2005 at Bankoku Shinryoukan in Okinawa, Japan. Since the first Amaldi conference was held in Frascati in 1994, eleven years have passed and the scale of the conference has grown with the increasing activity in the field of gravitational waves. As the centenary celebration of Einstein's 'miracle year', 2005 was called 'World Year of Physics'. Among his breakthroughs published in 1905, the special theory of relativity is recognized as the most significant revolution in physics, completely changing our views concerning time and space. Ten years later, Einstein proposed the general theory of relativity, by which he predicted the existence of gravitational waves (GWs). At that time, it was only a dream to observe a GW because its effect was so small. Efforts to detect GWs, pioneered by Weber, have continued for almost 40 years, yet their detection remained a dream. However, the presentations at this conference have convinced us that it is no longer a dream. The GW detector projects have made extraordinary advances; in particular, the significant sensitivity improvement of LIGO and the completion of the VIRGO detector mark the beginning of the new era of GW physics. Firm developments in theories and source estimations were also reported. In particular, the data analysis session was very active and various discussions were held. Elaborate experimental techniques were presented, some of them already achieving the requirements for the next generation of detectors, such as Advanced LIGO and LCGT. In addition to the earth-based detectors, many presentations concerning space detectors were contributed; they indicated that space would become the new stage for GW physics and astronomy. This issue brings together the papers which were presented at this exciting conference. The proceedings comprise two volumes; the largest part is published as a volume of

  1. Natural frequency of regular basins

    NASA Astrophysics Data System (ADS)

    Tjandra, Sugih S.; Pudjaprasetya, S. R.

    2014-03-01

    Similar to the vibration of a guitar string or an elastic membrane, water waves in an enclosed basin undergo standing oscillatory waves, also known as seiches. The resonant (eigen) periods of seiches are determined by water depth and geometry of the basin. For regular basins, explicit formulas are available. Resonance occurs when the dominant frequency of external force matches the eigen frequency of the basin. In this paper, we implement the conservative finite volume scheme to 2D shallow water equation to simulate resonance in closed basins. Further, we would like to use this scheme and utilizing energy spectra of the recorded signal to extract resonant periods of arbitrary basins. But here we first test the procedure for getting resonant periods of a square closed basin. The numerical resonant periods that we obtain are comparable with those from analytical formulas.

  2. Regularized degenerate multi-solitons

    NASA Astrophysics Data System (ADS)

    Correa, Francisco; Fring, Andreas

    2016-09-01

    We report complex {P}{T} -symmetric multi-soliton solutions to the Korteweg de-Vries equation that asymptotically contain one-soliton solutions, with each of them possessing the same amount of finite real energy. We demonstrate how these solutions originate from degenerate energy solutions of the Schrödinger equation. Technically this is achieved by the application of Darboux-Crum transformations involving Jordan states with suitable regularizing shifts. Alternatively they may be constructed from a limiting process within the context Hirota's direct method or on a nonlinear superposition obtained from multiple Bäcklund transformations. The proposed procedure is completely generic and also applicable to other types of nonlinear integrable systems.

  3. Rule extraction by successive regularization.

    PubMed

    Ishikawa, M

    2000-12-01

    Knowledge acquisition is, needless to say, important, because it is a key to the solution to one of the bottlenecks in artificial intelligence. Recently, knowledge acquisition using neural networks, called rule extraction, is attracting wide attention because of its computational simplicity and ability to generalize. Proposed in this paper is a novel approach to rule extraction named successive regularization. It generates a small number of dominant rules at an earlier stage and less dominant rules or exceptions at later stages. It has various advantages such as robustness of computation, better understanding, and similarity to child development. It is applied to the classification of mushrooms, the recognition of promoters in DNA sequences and the classification of irises. Empirical results indicate superior performance of rule extraction in terms of the number and the size of rules for explaining data.

  4. 9 CFR 381.68 - Maximum inspection rates-New turkey inspection system.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 9 Animals and Animal Products 2 2013-01-01 2013-01-01 false Maximum inspection rates-New turkey... Procedures § 381.68 Maximum inspection rates—New turkey inspection system. (a) The maximum inspection rates for one inspector New Turkey Inspection (NTI-1 and NTI-1 Modified) and two inspectors New Turkey...

  5. 9 CFR 381.68 - Maximum inspection rates-New turkey inspection system.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Maximum inspection rates-New turkey... Procedures § 381.68 Maximum inspection rates—New turkey inspection system. (a) The maximum inspection rates for one inspector New Turkey Inspection (NTI-1 and NTI-1 Modified) and two inspectors New Turkey...

  6. Some Cosine Relations and the Regular Heptagon

    ERIC Educational Resources Information Center

    Osler, Thomas J.; Heng, Phongthong

    2007-01-01

    The ancient Greek mathematicians sought to construct, by use of straight edge and compass only, all regular polygons. They had no difficulty with regular polygons having 3, 4, 5 and 6 sides, but the 7-sided heptagon eluded all their attempts. In this article, the authors discuss some cosine relations and the regular heptagon. (Contains 1 figure.)

  7. Regular Pentagons and the Fibonacci Sequence.

    ERIC Educational Resources Information Center

    French, Doug

    1989-01-01

    Illustrates how to draw a regular pentagon. Shows the sequence of a succession of regular pentagons formed by extending the sides. Calculates the general formula of the Lucas and Fibonacci sequences. Presents a regular icosahedron as an example of the golden ratio. (YP)

  8. 22 CFR 120.39 - Regular employee.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 22 Foreign Relations 1 2013-04-01 2013-04-01 false Regular employee. 120.39 Section 120.39 Foreign Relations DEPARTMENT OF STATE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS PURPOSE AND DEFINITIONS § 120.39 Regular employee. (a) A regular employee means for purposes of this subchapter: (1) An...

  9. 22 CFR 120.39 - Regular employee.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 22 Foreign Relations 1 2014-04-01 2014-04-01 false Regular employee. 120.39 Section 120.39 Foreign Relations DEPARTMENT OF STATE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS PURPOSE AND DEFINITIONS § 120.39 Regular employee. (a) A regular employee means for purposes of this subchapter: (1) An...

  10. 22 CFR 120.39 - Regular employee.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 22 Foreign Relations 1 2012-04-01 2012-04-01 false Regular employee. 120.39 Section 120.39 Foreign Relations DEPARTMENT OF STATE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS PURPOSE AND DEFINITIONS § 120.39 Regular employee. (a) A regular employee means for purposes of this subchapter: (1) An...

  11. Development of inspection robots for bridge cables.

    PubMed

    Yun, Hae-Bum; Kim, Se-Hoon; Wu, Liuliu; Lee, Jong-Jae

    2013-01-01

    This paper presents the bridge cable inspection robot developed in Korea. Two types of the cable inspection robots were developed for cable-suspension bridges and cable-stayed bridge. The design of the robot system and performance of the NDT techniques associated with the cable inspection robot are discussed. A review on recent advances in emerging robot-based inspection technologies for bridge cables and current bridge cable inspection methods is also presented.

  12. Development of Inspection Robots for Bridge Cables

    PubMed Central

    Kim, Se-Hoon; Lee, Jong-Jae

    2013-01-01

    This paper presents the bridge cable inspection robot developed in Korea. Two types of the cable inspection robots were developed for cable-suspension bridges and cable-stayed bridge. The design of the robot system and performance of the NDT techniques associated with the cable inspection robot are discussed. A review on recent advances in emerging robot-based inspection technologies for bridge cables and current bridge cable inspection methods is also presented. PMID:24459453

  13. On Site Inspection Radionuclide Measurements

    NASA Astrophysics Data System (ADS)

    Hayes, J. C.; Haas, D.; Milbrath, B. D.; Miley, H.; Seifert, C. E.

    2013-12-01

    The goal of an On Site Inspection for the CTBT is the clarification of the nature of a triggering event - probably a seismic signal. After a request for inspection is made and accepted, an inspection team proceeds to the environs of the triggering event and uses visual, seismic, radiological, or other location-finding methods to narrow down the search area. Survey, environmental sampling, and field-lab measurement methods then are used to try to collect definitive facts to support decisions of an Executive Council of the Treaty. Refining and optimizing the science methods for practical survey, sampling, and measurement requires reasonable measurement objectives to be stated. The authors will present a few scenario-dependant objectives such that the field approaches and equipment specifications could follow.

  14. Serpentine Robots for Inspection Tasks

    SciTech Connect

    Choset, Howie

    2003-09-11

    Serpentine robots are snake like devices that can use their internal degrees of freedom to thread through tightly packed volumes accessing locations that people or conventional machinery cannot. These devices are ideally suited for minimally invasive inspection tasks where the surrounding areas do not have to be disturbed. Applications for these devices are therefore inspection of underground tanks and other storage facilities for classification purposes. This work deals with the design, construction, and control of a serpentine robot. The challenges lie in developing a device that can lift itself in three dimensions, which is necessary for the inspection tasks. The other challenge in control deals with coordinating all of the internal degrees of freedom to exact purposeful motion.

  15. Class of regular bouncing cosmologies

    NASA Astrophysics Data System (ADS)

    Vasilić, Milovan

    2017-06-01

    In this paper, I construct a class of everywhere regular geometric sigma models that possess bouncing solutions. Precisely, I show that every bouncing metric can be made a solution of such a model. My previous attempt to do so by employing one scalar field has failed due to the appearance of harmful singularities near the bounce. In this work, I use four scalar fields to construct a class of geometric sigma models which are free of singularities. The models within the class are parametrized by their background geometries. I prove that, whatever background is chosen, the dynamics of its small perturbations is classically stable on the whole time axis. Contrary to what one expects from the structure of the initial Lagrangian, the physics of background fluctuations is found to carry two tensor, two vector, and two scalar degrees of freedom. The graviton mass, which naturally appears in these models, is shown to be several orders of magnitude smaller than its experimental bound. I provide three simple examples to demonstrate how this is done in practice. In particular, I show that graviton mass can be made arbitrarily small.

  16. A new approach for defect inspection on large area masks

    NASA Astrophysics Data System (ADS)

    Scheuring, Gerd; Döbereiner, Stefan; Hillmann, Frank; Falk, Günther; Brück, Hans-Jürgen

    2007-02-01

    Besides the mask market for IC manufacturing, which mainly uses 6 inch sized masks, the market for the so called large area masks is growing very rapidly. Typical applications of these masks are mainly wafer bumping for current packaging processes, color filters on TFTs, and Flip Chip manufacturing. To expose e.g. bumps and similar features on 200 mm wafers under proximity exposure conditions 9 inch masks are used, while in 300 mm wafer bumping processes (Fig. 1) 14 inch masks are handled. Flip Chip manufacturing needs masks up to 28 by 32 inch. This current maximum mask dimension is expected to hold for the next 5 years in industrial production. On the other hand shrinking feature sizes, just as in case of the IC masks, demand enhanced sensitivity of the inspection tools. A defect inspection tool for those masks is valuable for both the mask maker, who has to deliver a defect free mask to his customer, and for the mask user to supervise the mask behavior conditions during its lifetime. This is necessary because large area masks are mainly used for proximity exposures. During this process itself the mask is vulnerable by contacting the resist on top of the wafers. Therefore a regular inspection of the mask after 25, 50, or 100 exposures has to be done during its whole lifetime. Thus critical resist contamination and other defects, which lead to yield losses, can be recognized early. In the future shrinking feature dimensions will require even more sensitive and reliable defect inspection methods than they do presently. Besides the sole inspection capability the tools should also provide highly precise measurement capabilities and extended review options.

  17. 9 CFR 354.121 - Ante-mortem inspection.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY INSPECTION AND CERTIFICATION VOLUNTARY INSPECTION OF RABBITS AND EDIBLE PRODUCTS THEREOF Inspection Procedures; Ante-Mortem Inspections § 354.121 Ante-mortem inspection. An ante-mortem inspection of...

  18. Guided acoustic wave inspection system

    SciTech Connect

    Chinn, Diane J.

    2004-10-05

    A system for inspecting a conduit for undesirable characteristics. A transducer system induces guided acoustic waves onto said conduit. The transducer system detects the undesirable characteristics of the conduit by receiving guided acoustic waves that contain information about the undesirable characteristics. The conduit has at least two sides and the transducer system utilizes flexural modes of propagation to provide inspection using access from only the one side of the conduit. Cracking is detected with pulse-echo testing using one transducer to both send and receive the guided acoustic waves. Thinning is detected in through-transmission testing where one transducer sends and another transducer receives the guided acoustic waves.

  19. Evaluation of inservice inspection examinatiions

    SciTech Connect

    Aldrich, D.A.; Cook, J.F.

    1990-05-01

    In order to evaluate the effectiveness of Section 11, Division 1, ``Rules for Inservice Inspection of Nuclear Power Plant Components,`` of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code examinations, 26 inservice inspection (ISI) summary reports from 24 facilities were reviewed. It was found that these ASME Code examinations and tests are instrumental in revealing indications and defects in welds and plant components. In addition, this study uncovered that fact that some of the Section 11 requirements are apparently not clear and are misunderstood by some of the facilities. Also, the need for more stringent requirements was evaluated and some Code changes are recommended.

  20. Evaluation of inservice inspection examinatiions

    SciTech Connect

    Aldrich, D.A.; Cook, J.F.

    1990-05-01

    In order to evaluate the effectiveness of Section 11, Division 1, Rules for Inservice Inspection of Nuclear Power Plant Components,'' of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code examinations, 26 inservice inspection (ISI) summary reports from 24 facilities were reviewed. It was found that these ASME Code examinations and tests are instrumental in revealing indications and defects in welds and plant components. In addition, this study uncovered that fact that some of the Section 11 requirements are apparently not clear and are misunderstood by some of the facilities. Also, the need for more stringent requirements was evaluated and some Code changes are recommended.

  1. 9 CFR 590.126 - Overtime inspection service.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... EGG PRODUCTS INSPECTION INSPECTION OF EGGS AND EGG PRODUCTS (EGG PRODUCTS INSPECTION ACT) Performance... outside the established schedule, such services are considered as overtime work. The official plant...

  2. 9 CFR 354.65 - Form of inspection mark.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY INSPECTION AND CERTIFICATION VOLUNTARY INSPECTION OF RABBITS AND EDIBLE PRODUCTS THEREOF Identifying...

  3. 9 CFR 354.74 - Prerequisites to inspection.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY INSPECTION AND CERTIFICATION VOLUNTARY INSPECTION OF RABBITS AND EDIBLE PRODUCTS THEREOF Supervision...

  4. 9 CFR 354.134 - Appeal inspections; how made.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY INSPECTION AND CERTIFICATION VOLUNTARY INSPECTION OF RABBITS AND EDIBLE PRODUCTS THEREOF Appeals §...

  5. 9 CFR 354.30 - Who may obtain inspection service.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AGRICULTURE AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY INSPECTION AND CERTIFICATION VOLUNTARY INSPECTION OF RABBITS AND EDIBLE PRODUCTS THEREOF Application...

  6. 9 CFR 354.90 - Report of inspection work.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY INSPECTION AND CERTIFICATION VOLUNTARY INSPECTION OF RABBITS AND EDIBLE PRODUCTS THEREOF Reports §...

  7. A multiplicative regularization for force reconstruction

    NASA Astrophysics Data System (ADS)

    Aucejo, M.; De Smet, O.

    2017-02-01

    Additive regularizations, such as Tikhonov-like approaches, are certainly the most popular methods for reconstructing forces acting on a structure. These approaches require, however, the knowledge of a regularization parameter, that can be numerically computed using specific procedures. Unfortunately, these procedures are generally computationally intensive. For this particular reason, it could be of primary interest to propose a method able to proceed without defining any regularization parameter beforehand. In this paper, a multiplicative regularization is introduced for this purpose. By construction, the regularized solution has to be calculated in an iterative manner. In doing so, the amount of regularization is automatically adjusted throughout the resolution process. Validations using synthetic and experimental data highlight the ability of the proposed approach in providing consistent reconstructions.

  8. Total variation regularization with bounded linear variations

    NASA Astrophysics Data System (ADS)

    Makovetskii, Artyom; Voronin, Sergei; Kober, Vitaly

    2016-09-01

    One of the most known techniques for signal denoising is based on total variation regularization (TV regularization). A better understanding of TV regularization is necessary to provide a stronger mathematical justification for using TV minimization in signal processing. In this work, we deal with an intermediate case between one- and two-dimensional cases; that is, a discrete function to be processed is two-dimensional radially symmetric piecewise constant. For this case, the exact solution to the problem can be obtained as follows: first, calculate the average values over rings of the noisy function; second, calculate the shift values and their directions using closed formulae depending on a regularization parameter and structure of rings. Despite the TV regularization is effective for noise removal; it often destroys fine details and thin structures of images. In order to overcome this drawback, we use the TV regularization for signal denoising subject to linear signal variations are bounded.

  9. Artificial Intelligence Assists Ultrasonic Inspection

    NASA Technical Reports Server (NTRS)

    Schaefer, Lloyd A.; Willenberg, James D.

    1992-01-01

    Subtle indications of flaws extracted from ultrasonic waveforms. Ultrasonic-inspection system uses artificial intelligence to help in identification of hidden flaws in electron-beam-welded castings. System involves application of flaw-classification logic to analysis of ultrasonic waveforms.

  10. FAA Fluorescent Penetrant Laboratory Inspections

    SciTech Connect

    WINDES,CONNOR L.; MOORE,DAVID G.

    2000-08-02

    The Federal Aviation Administration Airworthiness Assurance NDI Validation Center currently assesses the capability of various non-destructive inspection (NDI) methods used for analyzing aircraft components. The focus of one such exercise is to evaluate the sensitivity of fluorescent liquid penetrant inspection. A baseline procedure using the water-washable fluorescent penetrant method defines a foundation for comparing the brightness of low cycle fatigue cracks in titanium test panels. The analysis of deviations in the baseline procedure will determine an acceptable range of operation for the steps in the inspection process. The data also gives insight into the depth of each crack and which step(s) of the inspection process most affect penetrant sensitivities. A set of six low cycle fatigue cracks produced in 6.35-mm thick Ti-6Al-4V specimens was used to conduct the experiments to produce sensitivity data. The results will document the consistency of the crack readings and compare previous experiments to find the best parameters for water-washable penetrant.

  11. Robotic Welding and Inspection System

    SciTech Connect

    H. B. Smartt; D. P. Pace; E. D. Larsen; T. R. McJunkin; C. I. Nichol; D. E. Clark; K. L. Skinner; M. L. Clark; T. G. Kaser; C. R. Tolle

    2008-06-01

    This paper presents a robotic system for GTA welding of lids on cylindrical vessels. The system consists of an articulated robot arm, a rotating positioner, end effectors for welding, grinding, ultrasonic and eddy current inspection. Features include weld viewing cameras, modular software, and text-based procedural files for process and motion trajectories.

  12. Cathodic protection system inspection 5

    NASA Astrophysics Data System (ADS)

    Jenkins, Jim; Polly, Dan

    1994-02-01

    The rectifier is the heart of an impressed current cathodic protection system. As it is subject to many adverse conditions including power surges, lightning strikes, vandalism, physical damage, and deterioration from atmospheric exposure, frequent inspections of rectifiers are vital to keeping an impressed current system operating so that it can provide nearly continuous protection of the underground, or submerged structures that are being protected.

  13. Oregon Schools Begin Inspection, Cleanup.

    ERIC Educational Resources Information Center

    Buckley, James F.

    1987-01-01

    Discusses the need for environmental health inspections in schools. Reports on the results of a survey of Clackamas County (Oregon) school kitchens, in relation to a high incidence of hepatitis A. Describes the variety of violations found and urges that schools no longer be exempt from state health division regulations. (TW)

  14. Oregon Schools Begin Inspection, Cleanup.

    ERIC Educational Resources Information Center

    Buckley, James F.

    1987-01-01

    Discusses the need for environmental health inspections in schools. Reports on the results of a survey of Clackamas County (Oregon) school kitchens, in relation to a high incidence of hepatitis A. Describes the variety of violations found and urges that schools no longer be exempt from state health division regulations. (TW)

  15. Artificial Intelligence Assists Ultrasonic Inspection

    NASA Technical Reports Server (NTRS)

    Schaefer, Lloyd A.; Willenberg, James D.

    1992-01-01

    Subtle indications of flaws extracted from ultrasonic waveforms. Ultrasonic-inspection system uses artificial intelligence to help in identification of hidden flaws in electron-beam-welded castings. System involves application of flaw-classification logic to analysis of ultrasonic waveforms.

  16. Electrical submersible pump teardown inspection

    SciTech Connect

    Lea, J.F.; Powers, W.J.

    1984-05-01

    This article deals with the details of an electrical submersible pump motor inspection. The ESP motor is shown in the disassembly fixture (vise). What to look for is discussed, such as the condition of the motor housing; if there is any heavy or light scale which could have added to motor heating and possible buildup; corrosion and any dents, scratches or bending.

  17. Testing times: regularities in the historical sciences.

    PubMed

    Jeffares, Ben

    2008-12-01

    The historical sciences, such as geology, evolutionary biology, and archaeology, appear to have no means to test hypotheses. However, on closer examination, reasoning in the historical sciences relies upon regularities, regularities that can be tested. I outline the role of regularities in the historical sciences, and in the process, blur the distinction between the historical sciences and the experimental sciences: all sciences deploy theories about the world in their investigations.

  18. Regularity effect in prospective memory during aging

    PubMed Central

    Blondelle, Geoffrey; Hainselin, Mathieu; Gounden, Yannick; Heurley, Laurent; Voisin, Hélène; Megalakaki, Olga; Bressous, Estelle; Quaglino, Véronique

    2016-01-01

    Background Regularity effect can affect performance in prospective memory (PM), but little is known on the cognitive processes linked to this effect. Moreover, its impacts with regard to aging remain unknown. To our knowledge, this study is the first to examine regularity effect in PM in a lifespan perspective, with a sample of young, intermediate, and older adults. Objective and design Our study examined the regularity effect in PM in three groups of participants: 28 young adults (18–30), 16 intermediate adults (40–55), and 25 older adults (65–80). The task, adapted from the Virtual Week, was designed to manipulate the regularity of the various activities of daily life that were to be recalled (regular repeated activities vs. irregular non-repeated activities). We examine the role of several cognitive functions including certain dimensions of executive functions (planning, inhibition, shifting, and binding), short-term memory, and retrospective episodic memory to identify those involved in PM, according to regularity and age. Results A mixed-design ANOVA showed a main effect of task regularity and an interaction between age and regularity: an age-related difference in PM performances was found for irregular activities (older < young), but not for regular activities. All participants recalled more regular activities than irregular ones with no age effect. It appeared that recalling of regular activities only involved planning for both intermediate and older adults, while recalling of irregular ones were linked to planning, inhibition, short-term memory, binding, and retrospective episodic memory. Conclusion Taken together, our data suggest that planning capacities seem to play a major role in remembering to perform intended actions with advancing age. Furthermore, the age-PM-paradox may be attenuated when the experimental design is adapted by implementing a familiar context through the use of activities of daily living. The clinical implications of regularity

  19. European Conference on Visual Perception (6th).

    DTIC Science & Technology

    1983-11-30

    Institut fuer Verhaltenswissenschaft, ETH- Zentrum, 8092 Zuerich - Switzerland W. GERBINO: Istituto di Psicologia , Universitk di Padova, Piazza Capitaniato...fuer medizinische Psychologie, Schillerstrasse 42 - 8000 Muenchen 2, West Germany L. JANEZ ESCALADA: Psicologia Matem&tica, Facultad de Psicologla...Norway P. MANCINI: Istituto di Fisiologia clinica del C.N.R., Via Bonanno Pisano - 56100 Pisa, Italy C.A. MARZI: Istituto di Psicologia . Universit

  20. Elementary Science Guide -- 6th Grade.

    ERIC Educational Resources Information Center

    Wieland, Anne; And Others

    Presented is a resource book to be used with instructional kits for elementary school science students, grade 6. The individual units at this grade level are based on curriculum which has been developed by the National Science Foundation in the 1960s and revised to meet student and teacher identified needs in Anchorage, Alaska. Six units are…