Science.gov

Sample records for 78-001 pwr core

  1. Influence Of Low Boron Core Design On PWR Transient Behavior

    SciTech Connect

    Aleksandrov Papukchiev, Angel; Yubo Liu; Schaefer, Anselm

    2006-07-01

    In conventional pressurized water reactor (PWR) designs, the concentration of boron in primary coolant is limited by the requirement of having a negative moderator density coefficient. As high boron concentrations have significant impact on reactivity feedback properties, design changes to reduce boron concentration in the reactor coolant are of general interest in view of improving PWR inherent safety. In the framework of an investigation into the feasibility of low boron design, a PWR core configuration based on fuel with higher gadolinium (Gd) content has been developed which permits to reduce the natural boron concentration at begin of cycle (BOC) by approx. 50% compared to current German PWR technology. For the assessment of the potential safety advantages, a Loss-of-Feedwater Anticipated Transient Without Scram (ATWS LOFW) has been simulated with the system code ATHLET for two PWR core designs: a low boron design and a standard core design. The most significant difference in the transient performance of both designs is the total primary fluid mass released through the pressurizer (PRZ) valves. It is reduced by a factor of four for the low boron reactor, indicating its improved density reactivity feedback. (authors)

  2. RIA Limits Based On Commercial PWR Core Response To RIA

    SciTech Connect

    Beard, Charles L.; Mitchell, David B.; Slagle, William H.

    2006-07-01

    Reactivity insertion accident (RIA) limits have been under intense review by regulators since 1993 with respect to what should be the proper limit as a function of burnup. Some national regulators have imposed new lower limits while in the United States the limits are still under review. The data being evaluated with respect to RIA limits come from specialized test reactors. However, the use of test reactor data needs to be balanced against the response of a commercial PWR core in setting reasonable limits to insure the health and safety of the public without unnecessary restrictions on core design and operation. The energy deposition limits for a RIA were set in the 1970's based on testing in CDC (SPERT), TREAT, PBF and NSRR test reactors. The US limits given in radially averaged enthalpy are 170 cal/gm for fuel cladding failure and 280 cal/gm for coolability. Testing conducted in the 1990's in the CABRI, NSRR and IGR test reactors have demonstrated that the cladding failure threshold is reduced with burnup, with the primary impact due to hydrogen pickup for in-reactor corrosion. Based on a review of this data very low enthalpy limits have been proposed. In reviewing proposed limits from RIL-0401(1) it was observed that much of the data used to anchor the low allowable energy deposition levels was from recent NSRR tests which do not represent commercial PWR reactor conditions. The particular characteristics of the NSRR test compared to commercial PWR reactor characteristics are: - Short pulse width: 4.5 ms vs > 8 ms; - Low temperature conditions: < 100 deg. F vs 532 deg. F. - Low pressure environment: atmospheric vs {approx} 2200 psi. A review of the historical RIA database indicates that some of the key NSRR data used to support the RIL was atypical compared to the overall RIA database. Based on this detailed review of the RIA database and the response of commercial PWR core, the following view points are proposed. - The Failure limit should reflect local fuel

  3. PWR cores with silicon carbide cladding

    SciTech Connect

    Dobisesky, J. P.; Carpenter, D.; Pilat, E.; Kazimi, M. S.

    2012-07-01

    The feasibility of using silicon carbide rather than Zircaloy cladding, to reach higher power levels and higher discharge burnups in PWRs has been evaluated. A preliminary fuel design using fuel rods with the same dimensions as in the Westinghouse Robust Fuel Assembly but with fuel pellets having 10 vol% central void has been adopted to mitigate the higher fuel temperatures that occur due to the lower thermal conductivity of the silicon carbide and to the persistence of the open clad-pellet gap over most of the fuel life. With this modified fuel design, it is possible to achieve 18 month cycles that meet present-day operating constraints on peaking factor, boron concentration, reactivity coefficients and shutdown margin, while allowing batch average discharge burnups up to 80 MWD/kgU and peak rod burnups up to 100 MWD/kgU. Power uprates of 10% and possibly 20% also appear feasible. For non-uprated cores, the silicon carbide-clad fuel has a clear advantage that increases with increasing discharge burnup. Even for comparable discharge burnups, there is a savings in enriched uranium. Control rod configuration modifications may be required to meet the shutdown margin criterion for the 20% up-rate. Silicon carbide's ability to sustain higher burnups than Zircaloy also allows the design of a licensable two year cycle with only 96 fresh assemblies, avoiding the enriched uranium penalty incurred with use of larger batch sizes due to their excessive leakage. (authors)

  4. ACHILLES: Heat Transfer in PWR Core During LOCA Reflood Phase

    SciTech Connect

    2013-11-01

    1. NAME AND TITLE OF DATA LIBRARY ACHILLES -Heat Transfer in PWR Core During LOCA Reflood Phase. 2. NAME AND TITLE OF DATA RETRIEVAL PROGRAMS N/A 3. CONTRIBUTOR AEA Technology, Winfrith Technology Centre, Dorchester DT2 8DH United Kingdom through the OECD Nuclear Energy Agency Data Bank, Issy-les-Moulineaux, France. 4. DESCRIPTION OF TEST FACILITY The most important features of the Achilles rig were the shroud vessel, which contained the test section, and the downcomer. These may be thought of as representing the core barrel and the annular downcomer in the reactor pressure vessel. The test section comprises a cluster of 69 rods in a square array within a circular shroud vessel. The rod diameter and pitch (9.5 mm and 12.6 mm) were typical of PWR dimensions. The internal diameter of the shroud vessel was 128 mm. Each rod was electrically heated over a length of 3.66 m, which is typical of the nuclear heated length in a PWR fuel rod, and each contained 6 internal thermocouples. These were arranged in one of 8 groupings which concentrated the thermocouples in different axial zones. The spacer grids were at prototypic PWR locations. Each grid had two thermocouples attached to its trailing edge at radial locations. The axial power profile along the rods was an 11 step approximation to a "chopped cosine". The shroud vessel had 5 heating zones whose power could be independently controlled. 5. DESCRIPTION OF TESTS The Achilles experiments investigated the heat transfer in the core of a Pressurized Water Reactor during the re-flood phase of a postulated large break loss of coolant accident. The results provided data to validate codes and to improve modeling. Different types of experiments were carried out which included single phase cooling, re-flood under low flow conditions, level swell and re-flood under high flow conditions. Three series of experiments were performed. The first and the third used the same test section but the second used another test section, similar in

  5. VERA Core Simulator Methodology for PWR Cycle Depletion

    SciTech Connect

    Kochunas, Brendan; Collins, Benjamin S; Jabaay, Daniel; Kim, Kang Seog; Graham, Aaron; Stimpson, Shane; Wieselquist, William A; Clarno, Kevin T; Palmtag, Scott; Downar, Thomas; Gehin, Jess C

    2015-01-01

    This paper describes the methodology developed and implemented in MPACT for performing high-fidelity pressurized water reactor (PWR) multi-cycle core physics calculations. MPACT is being developed primarily for application within the Consortium for the Advanced Simulation of Light Water Reactors (CASL) as one of the main components of the VERA Core Simulator, the others being COBRA-TF and ORIGEN. The methods summarized in this paper include a methodology for performing resonance self-shielding and computing macroscopic cross sections, 2-D/1-D transport, nuclide depletion, thermal-hydraulic feedback, and other supporting methods. These methods represent a minimal set needed to simulate high-fidelity models of a realistic nuclear reactor. Results demonstrating this are presented from the simulation of a realistic model of the first cycle of Watts Bar Unit 1. The simulation, which approximates the cycle operation, is observed to be within 50 ppm boron (ppmB) reactivity for all simulated points in the cycle and approximately 15 ppmB for a consistent statepoint. The verification and validation of the PWR cycle depletion capability in MPACT is the focus of two companion papers.

  6. IN-CORE FUEL MANAGEMENT: PWR Core Calculations Using MCRAC

    NASA Astrophysics Data System (ADS)

    PetroviĆ, B. G.

    1991-01-01

    The following sections are included: * INTRODUCTION * IN-CORE FUEL MANAGEMENT CALCULATIONS * In-Core Fuel Management * Methodological Problems of In-Core Fuel Management * In-Core Fuel Management Analytical Tools * PENN STATE FUEL MANAGEMENT PACKAGE * Penn State Fuel Management Package (PFMP) * Assembly Data Description (ADD) * Linking PSU-LEOPARD and MCRAC: An Example * MULTICYCLE REACTOR ANALYSIS CODE (MCRAC) * Main Features and Options of MCRAC code * Core geometry * Diffusion equations * 1.5-group model * Multicycle neutronic analysis * Multicycle cost analysis * Criticality search * Power-dependent xenon feedback calculations * Control rod and burnable absorber simulation * Search for LP with flat BOC power distribution * Artificial ADD option * Variable dimensioning technique * RBI version of MCRAC code * Programming changes in PC version * Fuel interchange option * MCRAC Input/Output * General input description * Sample input * Sample output * EXPERIENCE WITH MCRAC CODE * CONCLUSIONS * REFERENCES

  7. 103. PWR2 CORE SUPPORT FLANGE BEING SEATED ON REACTOR VESSEL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    103. PWR-2 CORE SUPPORT FLANGE BEING SEATED ON REACTOR VESSEL FLANGE, APRIL 14, 1964 - Shippingport Atomic Power Station, On Ohio River, 25 miles Northwest of Pittsburgh, Shippingport, Beaver County, PA

  8. Coupled Neutronics Thermal-Hydraulic Solution of a Full-Core PWR Using VERA-CS

    SciTech Connect

    Clarno, Kevin T; Palmtag, Scott; Davidson, Gregory G; Salko, Robert K; Evans, Thomas M; Turner, John A; Belcourt, Kenneth; Hooper, Russell; Schmidt, Rodney

    2014-01-01

    The Consortium for Advanced Simulation of Light Water Reactors (CASL) is developing a core simulator called VERA-CS to model operating PWR reactors with high resolution. This paper describes how the development of VERA-CS is being driven by a set of progression benchmark problems that specify the delivery of useful capability in discrete steps. As part of this development, this paper will describe the current capability of VERA-CS to perform a multiphysics simulation of an operating PWR at Hot Full Power (HFP) conditions using a set of existing computer codes coupled together in a novel method. Results for several single-assembly cases are shown that demonstrate coupling for different boron concentrations and power levels. Finally, high-resolution results are shown for a full-core PWR reactor modeled in quarter-symmetry.

  9. A highly heterogeneous 3D PWR core benchmark: deterministic and Monte Carlo method comparison

    NASA Astrophysics Data System (ADS)

    Jaboulay, J.-C.; Damian, F.; Douce, S.; Lopez, F.; Guenaut, C.; Aggery, A.; Poinot-Salanon, C.

    2014-06-01

    Physical analyses of the LWR potential performances with regards to the fuel utilization require an important part of the work dedicated to the validation of the deterministic models used for theses analyses. Advances in both codes and computer technology give the opportunity to perform the validation of these models on complex 3D core configurations closed to the physical situations encountered (both steady-state and transient configurations). In this paper, we used the Monte Carlo Transport code TRIPOLI-4®; to describe a whole 3D large-scale and highly-heterogeneous LWR core. The aim of this study is to validate the deterministic CRONOS2 code to Monte Carlo code TRIPOLI-4®; in a relevant PWR core configuration. As a consequence, a 3D pin by pin model with a consistent number of volumes (4.3 millions) and media (around 23,000) is established to precisely characterize the core at equilibrium cycle, namely using a refined burn-up and moderator density maps. The configuration selected for this analysis is a very heterogeneous PWR high conversion core with fissile (MOX fuel) and fertile zones (depleted uranium). Furthermore, a tight pitch lattice is selcted (to increase conversion of 238U in 239Pu) that leads to harder neutron spectrum compared to standard PWR assembly. In these conditions two main subjects will be discussed: the Monte Carlo variance calculation and the assessment of the diffusion operator with two energy groups for the core calculation.

  10. Optimization of burnable poison design for Pu incineration in fully fertile free PWR core

    SciTech Connect

    Fridman, E.; Shwageraus, E.; Galperin, A.

    2006-07-01

    The design challenges of the fertile-free based fuel (FFF) can be addressed by careful and elaborate use of burnable poisons (BP). Practical fully FFF core design for PWR reactor has been reported in the past [1]. However, the burnable poison option used in the design resulted in significant end of cycle reactivity penalty due to incomplete BP depletion. Consequently, excessive Pu loading were required to maintain the target fuel cycle length, which in turn decreased the Pu burning efficiency. A systematic evaluation of commercially available BP materials in all configurations currently used in PWRs is the main objective of this work. The BP materials considered are Boron, Gd, Er, and Hf. The BP geometries were based on Wet Annular Burnable Absorber (WABA), Integral Fuel Burnable Absorber (IFBA), and Homogeneous poison/fuel mixtures. Several most promising combinations of BP designs were selected for the full core 3D simulation. All major core performance parameters for the analyzed cases are very close to those of a standard PWR with conventional UO{sub 2} fuel including possibility of reactivity control, power peaking factors, and cycle length. The MTC of all FFF cores was found at the full power conditions at all times and very close to that of the UO{sub 2} core. The Doppler coefficient of the FFF cores is also negative but somewhat lower in magnitude compared to UO{sub 2} core. The soluble boron worth of the FFF cores was calculated to be lower than that of the UO{sub 2} core by about a factor of two, which still allows the core reactivity control with acceptable soluble boron concentrations. The main conclusion of this work is that judicial application of burnable poisons for fertile free fuel has a potential to produce a core design with performance characteristics close to those of the reference PWR core with conventional UO{sub 2} fuel. (authors)

  11. Assessment of void swelling in austenitic stainless steel PWR core internals.

    SciTech Connect

    Chung, H. M.; Energy Technology

    2006-01-31

    As many pressurized water reactors (PWRs) age and life extension of the aged plants is considered, void swelling behavior of austenitic stainless steel (SS) core internals has become the subject of increasing attention. In this report, the available database on void swelling and density change of austenitic SSs was critically reviewed. Irradiation conditions, test procedures, and microstructural characteristics were carefully examined, and key factors that are important to determine the relevance of the database to PWR conditions were evaluated. Most swelling data were obtained from steels irradiated in fast breeder reactors at temperatures >385 C and at dose rates that are orders of magnitude higher than PWR dose rates. Even for a given irradiation temperature and given steel, the integral effects of dose and dose rate on void swelling should not be separated. It is incorrect to extrapolate swelling data on the basis of 'progressive compounded multiplication' of separate effects of factors such as dose, dose rate, temperature, steel composition, and fabrication procedure. Therefore, the fast reactor data should not be extrapolated to determine credible void swelling behavior for PWR end-of-life (EOL) or life-extension conditions. Although the void swelling data extracted from fast reactor studies is extensive and conclusive, only limited amounts of swelling data and information have been obtained on microstructural characteristics from discharged PWR internals or steels irradiated at temperatures and at dose rates comparable to those of a PWR. Based on this relatively small amount of information, swelling in thin-walled tubes and baffle bolts in a PWR is not considered a concern. As additional data and relevant research becomes available, the newer results should be integrated with existing data, and the worthiness of this conclusion should continue to be scrutinized. PWR baffle reentrant corners are the most likely location to experience high swelling rates, and

  12. Multicycle PWR in-core fuel management through one-and-a-half-dimensional core modeling

    SciTech Connect

    Petrovic, B.G.; Levine, S.H. )

    1992-01-01

    The one-and-a-half-dimensional (1 and 1/2-D) model of a pressurized water reactor (PWR) core employs one-dimensional (1-D) diffusion calculation followed by a fast, few-step procedure to unfold the 1-D results into the two-dimensional (2-D) results. A computer code was developed based on that model. The initial benchmarking has shown the code to be almost as fast as a plain 1-D code and significantly faster than the analogous 2-D code (10 to 100 times for a typical problem). Yet, it provides results in 2-D form and better accuracy than the 1-D code. The model itself and the initial benchmarking were described in more detail elsewhere. The code has since been enhanced, and a multicycle analysis option has been implemented. This paper presents results of benchmarking the model using the actual data for three successive cycles of the Krsko nuclear power plant and complex low-leakage loading patterns.

  13. Support arrangements for core modules of nuclear reactors. [PWR

    DOEpatents

    Bollinger, L.R.

    1983-11-03

    A support arrangement is provided for the core modules of a nuclear reactor which provides support access through the control drive mechanisms of the reactor. This arrangement provides axial support of individual reactor core modules from the pressure vessel head in a manner which permits attachment and detachment of the modules from the head to be accomplished through the control drive mechanisms after their leadscrews have been removed. The arrangement includes a module support nut which is suspended from the pressure vessel head and screw threaded to the shroud housing for the module. A spline lock prevents loosening of the screw connection. An installation tool assembly, including a cell lifting and preloading tool and a torquing tool, fits through the control drive mechanism and provides lifting of the shroud housing while disconnecting the spline lock, as well as application of torque to the module support nut.

  14. 3D Neutron Transport PWR Full-core Calculation with RMC code

    NASA Astrophysics Data System (ADS)

    Qiu, Yishu; She, Ding; Fan, Xiao; Wang, Kan; Li, Zeguang; Liang, Jingang; Leroyer, Hadrien

    2014-06-01

    Nowadays, there are more and more interests in the use of Monte Carlo codes to calculate the detailed power density distributions in full-core reactors. With the Inspur TS1000 HPC Server of Tsinghua University, several calculations have been done based on the EDF 3D Neutron Transport PWR Full-core benchmark through large-scale parallelism. To investigate and compare the results of the deterministic method and Monte Carlo method, EDF R&D and Department of Engineering Physics of Tsinghua University are having a collaboration to make code to code verification. So in this paper, two codes are used. One is the code COCAGNE developed by the EDF R&D, a deterministic core code, and the other is the Monte Carlo code RMC developed by Department of Engineering Physics in Tsinghua University. First, the full-core model is described and a 26-group calculation was performed by these two codes using the same 26-group cross-section library provided by EDF R&D. Then the parallel and tally performance of RMC is discussed. RMC employs a novel algorithm which can cut down most of the communications. It can be seen clearly that the speedup ratio almost linearly increases with the nodes. Furthermore the cell-mapping method applied by RMC consumes little time to tally even millions of cells. The results of the codes COCAGNE and RMC are compared in three ways. The results of these two codes agree well with each other. It can be concluded that both COCAGNE and RMC are able to provide 3D-transport solutions associated with detailed power density distributions calculation in PWR full-core reactors. Finally, to investigate how many histories are needed to obtain a given standard deviation for a full 3D solution, the non-symmetrized condensed 2-group fluxes of RMC are discussed.

  15. CORMLT code for the analysis of degraded core accidents. Computer code manual. [PWR

    SciTech Connect

    Denny, V.E.

    1984-12-01

    A computer code (CORMLT) has been developed to predict the effects of bouyancy-driven convection on the progression of core-degrading accidents in PWR vessels. Thermal/hydraulics modeling includes the downcomer/bottom-head regions, as well as the upper vessel and adjacent hot-leg portions of the primary coolant system for which gas communication is limited to the intervening discharge nozzles (so-called dead-end volumes). CORMLT requires flow rates and temperatures of any water feed (to the downcomer) versus time. CORMLT provides composition, enthalpy, temperature, and flow rate of steam/hydrogen mixtures within the vessel above the (receding) water surface, as well as estimates of these quantities for interaction between the plenum and the rest of the PCS. CORMLT also provides graphical representations for the morphological behavior of the progression of core meltdown accidents.

  16. Conceptual Core Analysis of Long Life PWR Utilizing Thorium-Uranium Fuel Cycle

    NASA Astrophysics Data System (ADS)

    Rouf; Su'ud, Zaki

    2016-08-01

    Conceptual core analysis of long life PWR utilizing thorium-uranium based fuel has conducted. The purpose of this study is to evaluate neutronic behavior of reactor core using combined thorium and enriched uranium fuel. Based on this fuel composition, reactor core have higher conversion ratio rather than conventional fuel which could give longer operation length. This simulation performed using SRAC Code System based on library SRACLIB-JDL32. The calculation carried out for (Th-U)O2 and (Th-U)C fuel with uranium composition 30 - 40% and gadolinium (Gd2O3) as burnable poison 0,0125%. The fuel composition adjusted to obtain burn up length 10 - 15 years under thermal power 600 - 1000 MWt. The key properties such as uranium enrichment, fuel volume fraction, percentage of uranium are evaluated. Core calculation on this study adopted R-Z geometry divided by 3 region, each region have different uranium enrichment. The result show multiplication factor every burn up step for 15 years operation length, power distribution behavior, power peaking factor, and conversion ratio. The optimum core design achieved when thermal power 600 MWt, percentage of uranium 35%, U-235 enrichment 11 - 13%, with 14 years operation length, axial and radial power peaking factor about 1.5 and 1.2 respectively.

  17. Modeling and design of a reload PWR core for a 48-month fuel cycle

    SciTech Connect

    McMahon, M.V.; Driscoll, M.J.; Todreas, N.E.

    1997-05-01

    The objective of this research was to use state-of-the-art nuclear and fuel performance packages to evaluate the feasibility and costs of a 48 calendar month core in existing pressurized water reactor (PWR) designs, considering the full range of practical design and economic considerations. The driving force behind this research is the desire to make nuclear power more economically competitive with fossil fuel options by expanding the scope for achievement of higher capacity factors. Using CASMO/SIMULATE, a core design with fuel enriched to 7{sup w}/{sub o} U{sup 235} for a single batch loaded, 48-month fuel cycle has been developed. This core achieves an ultra-long cycle length without exceeding current fuel burnup limits. The design uses two different types of burnable poisons. Gadolinium in the form of gadolinium oxide (Gd{sub 2}O{sub 3}) mixed with the UO{sub 2} of selected pins is sued to hold down initial reactivity and to control flux peaking throughout the life of the core. A zirconium di-boride (ZrB{sub 2}) integral fuel burnable absorber (IFBA) coating on the Gd{sub 2}O{sub 3}-UO{sub 2} fuel pellets is added to reduce the critical soluble boron concentration in the reactor coolant to within acceptable limits. Fuel performance issues of concern to this design are also outlined and areas which will require further research are highlighted.

  18. Whole-core comet solutions to a 3-dimensional PWR benchmark problem with gadolinium

    SciTech Connect

    Zhang, D.; Rahnema, F.

    2012-07-01

    A pressurized water reactor (PWR) benchmark problem with gadolinium was used to determine the accuracy and computational efficiency of the coarse mesh radiation transport method COMET. The benchmark problem contains 193 square fuel assemblies. The COMET solution (eigenvalue, assembly averaged and fuel pin averaged fission density distributions) was compared with those obtained from the corresponding Monte Carlo reference solution using the same 2-group material cross section library. The comparison showed that both the core eigenvalue and fission density distribution averaged over each assembly and fuel pin predicated by COMET agree very well with the corresponding MCNP reference solution if the incident flux response expansion used in COMET is truncated at 2nd order in the two spatial and the two angular variables. The benchmark calculations indicate that COMET has Monte Carlo accuracy. In, particular, the eigenvalue difference between the codes ranged from 17 pcm to 35 pcm, being within 2 standard deviations of the calculational uncertainty. The mean flux weighted relative differences in the assembly and fuel pin fission densities were 0.47% and 0.65%, respectively. It was also found that COMET's full (whole) core computational speed is 30,000 times faster than MCNP in which only 1/8 of the core is modeled. It is estimated that COMET would have been about over 6 orders of magnitude faster than MCNP if the full core were also modeled in MCNP. (authors)

  19. VERA-CS Modeling and Simulation of PWR Main Steam Line Break Core Response to DNB

    SciTech Connect

    Salko, Robert K; Sung, Yixing; Kucukboyaci, Vefa; Xu, Yiban; Cao, Liping

    2016-01-01

    The Virtual Environment for Reactor Applications core simulator (VERA-CS) being developed by the Consortium for the Advanced Simulation of Light Water Reactors (CASL) includes coupled neutronics, thermal-hydraulics, and fuel temperature components with an isotopic depletion capability. The neutronics capability employed is based on MPACT, a three-dimensional (3-D) whole core transport code. The thermal-hydraulics and fuel temperature models are provided by the COBRA-TF (CTF) subchannel code. As part of the CASL development program, the VERA-CS (MPACT/CTF) code system was applied to model and simulate reactor core response with respect to departure from nucleate boiling ratio (DNBR) at the limiting time step of a postulated pressurized water reactor (PWR) main steamline break (MSLB) event initiated at the hot zero power (HZP), either with offsite power available and the reactor coolant pumps in operation (high-flow case) or without offsite power where the reactor core is cooled through natural circulation (low-flow case). The VERA-CS simulation was based on core boundary conditions from the RETRAN-02 system transient calculations and STAR-CCM+ computational fluid dynamics (CFD) core inlet distribution calculations. The evaluation indicated that the VERA-CS code system is capable of modeling and simulating quasi-steady state reactor core response under the steamline break (SLB) accident condition, the results are insensitive to uncertainties in the inlet flow distributions from the CFD simulations, and the high-flow case is more DNB limiting than the low-flow case.

  20. PWR core and spent fuel pool analysis using scale and nestle

    SciTech Connect

    Murphy, J. E.; Maldonado, G. I.; St Clair, R.; Orr, D.

    2012-07-01

    The SCALE nuclear analysis code system [SCALE, 2011], developed and maintained at Oak Ridge National Laboratory (ORNL) is widely recognized as high quality software for analyzing nuclear systems. The SCALE code system is composed of several validated computer codes and methods with standard control sequences, such as the TRITON/NEWT lattice physics sequence, which supplies dependable and accurate analyses for industry, regulators, and academia. Although TRITON generates energy-collapsed and space-homogenized few group cross sections, SCALE does not include a full-core nodal neutron diffusion simulation module within. However, in the past few years, the open-source NESTLE core simulator [NESTLE, 2003], originally developed at North Carolina State Univ. (NCSU), has been updated and upgraded via collaboration between ORNL and the Univ. of Tennessee (UT), so it now has a growingly seamless coupling to the TRITON/NEWT lattice physics [Galloway, 2010]. This study presents the methodology used to couple lattice physics data between TRITON and NESTLE in order to perform a three-dimensional full-core analysis employing a 'real-life' Duke Energy PWR as the test bed. The focus for this step was to compare the key parameters of core reactivity and radial power distribution versus plant data. Following the core analysis, following a three cycle burn, a spent fuel pool analysis was done using information generated from NESTLE for the discharged bundles and was compared to Duke Energy spent fuel pool models. The KENO control module from SCALE was employed for this latter stage of the project. (authors)

  1. PWR core design, neutronics evaluation and fuel cycle analysis for thorium-uranium breeding recycle

    SciTech Connect

    Bi, G.; Liu, C.; Si, S.

    2012-07-01

    This paper was focused on core design, neutronics evaluation and fuel cycle analysis for Thorium-Uranium Breeding Recycle in current PWRs, without any major change to the fuel lattice and the core internals, but substituting the UOX pellet with Thorium-based pellet. The fuel cycle analysis indicates that Thorium-Uranium Breeding Recycle is technically feasible in current PWRs. A 4-loop, 193-assembly PWR core utilizing 17 x 17 fuel assemblies (FAs) was taken as the model core. Two mixed cores were investigated respectively loaded with mixed reactor grade Plutonium-Thorium (PuThOX) FAs and mixed reactor grade {sup 233}U-Thorium (U{sub 3}ThOX) FAs on the basis of reference full Uranium oxide (UOX) equilibrium-cycle core. The UOX/PuThOX mixed core consists of 121 UOX FAs and 72 PuThOX FAs. The reactor grade {sup 233}U extracted from burnt PuThOX fuel was used to fabrication of U{sub 3}ThOX for starting Thorium-. Uranium breeding recycle. In UOX/U{sub 3}ThOX mixed core, the well designed U{sub 3}ThOX FAs with 1.94 w/o fissile uranium (mainly {sup 233}U) were located on the periphery of core as a blanket region. U{sub 3}ThOX FAs remained in-core for 6 cycles with the discharged burnup achieving 28 GWD/tHM. Compared with initially loading, the fissile material inventory in U{sub 3}ThOX fuel has increased by 7% via 1-year cooling after discharge. 157 UOX fuel assemblies were located in the inner of UOX/U{sub 3}ThOX mixed core refueling with 64 FAs at each cycle. The designed UOX/PuThOX and UOX/U{sub 3}ThOX mixed core satisfied related nuclear design criteria. The full core performance analyses have shown that mixed core with PuThOX loading has similar impacts as MOX on several neutronic characteristic parameters, such as reduced differential boron worth, higher critical boron concentration, more negative moderator temperature coefficient, reduced control rod worth, reduced shutdown margin, etc.; while mixed core with U{sub 3}ThOX loading on the periphery of core has no

  2. Severe accident modeling of a PWR core with different cladding materials

    SciTech Connect

    Johnson, S. C.; Henry, R. E.; Paik, C. Y.

    2012-07-01

    The MAAP v.4 software has been used to model two severe accident scenarios in nuclear power reactors with three different materials as fuel cladding. The TMI-2 severe accident was modeled with Zircaloy-2 and SiC as clad material and a SBO accident in a Zion-like, 4-loop, Westinghouse PWR was modeled with Zircaloy-2, SiC, and 304 stainless steel as clad material. TMI-2 modeling results indicate that lower peak core temperatures, less H 2 (g) produced, and a smaller mass of molten material would result if SiC was substituted for Zircaloy-2 as cladding. SBO modeling results indicate that the calculated time to RCS rupture would increase by approximately 20 minutes if SiC was substituted for Zircaloy-2. Additionally, when an extended SBO accident (RCS creep rupture failure disabled) was modeled, significantly lower peak core temperatures, less H 2 (g) produced, and a smaller mass of molten material would be generated by substituting SiC for Zircaloy-2 or stainless steel cladding. Because the rate of SiC oxidation reaction with elevated temperature H{sub 2}O (g) was set to 0 for this work, these results should be considered preliminary. However, the benefits of SiC as a more accident tolerant clad material have been shown and additional investigation of SiC as an LWR core material are warranted, specifically investigations of the oxidation kinetics of SiC in H{sub 2}O (g) over the range of temperatures and pressures relevant to severe accidents in LWR 's. (authors)

  3. A new advanced fixed in-core instrumentation for a PWR reactor

    NASA Astrophysics Data System (ADS)

    Barbet, M.; Guillery, M.

    1981-06-01

    Gamma thermometer studies have been done at E.D.F. for four years. These studies started in France with a feasibility study in 1975. E.D.F.'s scope was to develop a new fixed "in-core" instrumentation for PWR based on the gamma heat measurements. The advanced gamma thermometer design has been done in such a way to be able to manufacture strings of 6 to 9 detectors each. The results of gamma thermometer make up in 1976 were encouraging and E.D.F. went on to develop a gamma thermometer assembly for a reactor application. Before being mounted on the reactor vessel, the gamma thermometer strings are calibrated in a loop test by means of an electrical current giving the ΔT versus the specific power ( W/ g). The loop test simulates the thermohydraulic conditions in the reactor tube guide. Two gamma thermometer strings have been installed in the BUGEY 5 reactor since June 1979. Four gamma thermometer strings are provided for insertion in the TRICASTIN 2 reactor and four more gamma thermometer strings are manufactured to be ready for the start up of the TRICASTIN 3 reactor in 1980.

  4. Applicability of 3D Monte Carlo simulations for local values calculations in a PWR core

    NASA Astrophysics Data System (ADS)

    Bernard, Franck; Cochet, Bertrand; Jinaphanh, Alexis; Jacquet, Olivier

    2014-06-01

    As technical support of the French Nuclear Safety Authority, IRSN has been developing the MORET Monte Carlo code for many years in the framework of criticality safety assessment and is now working to extend its application to reactor physics. For that purpose, beside the validation for criticality safety (more than 2000 benchmarks from the ICSBEP Handbook have been modeled and analyzed), a complementary validation phase for reactor physics has been started, with benchmarks from IRPHEP Handbook and others. In particular, to evaluate the applicability of MORET and other Monte Carlo codes for local flux or power density calculations in large power reactors, it has been decided to contribute to the "Monte Carlo Performance Benchmark" (hosted by OECD/NEA). The aim of this benchmark is to monitor, in forthcoming decades, the performance progress of detailed Monte Carlo full core calculations. More precisely, it measures their advancement towards achieving high statistical accuracy in reasonable computation time for local power at fuel pellet level. A full PWR reactor core is modeled to compute local power densities for more than 6 million fuel regions. This paper presents results obtained at IRSN for this benchmark with MORET and comparisons with MCNP. The number of fuel elements is so large that source convergence as well as statistical convergence issues could cause large errors in local tallies, especially in peripheral zones. Various sampling or tracking methods have been implemented in MORET, and their operational effects on such a complex case have been studied. Beyond convergence issues, to compute local values in so many fuel regions could cause prohibitive slowing down of neutron tracking. To avoid this, energy grid unification and tallies preparation before tracking have been implemented, tested and proved to be successful. In this particular case, IRSN obtained promising results with MORET compared to MCNP, in terms of local power densities, standard

  5. Dosimetry Evaluation of In-Core and Above-Core Zirconium Alloy Samples in a PWR

    NASA Astrophysics Data System (ADS)

    Amiri, Benjamin W.; Foster, John P.; Greenwood, Larry R.

    2016-02-01

    A description of the neutron fluence analysis of activated zirconium alloys samples at a Westinghouse 3-loop reactor is presented. These samples were irradiated in the core and in the fuel plenum region, where dosimetry measurements are relatively rare compared with regions radially outward of the core. Dosimetry measurements performed by Batelle/PNNL are compared to the calculational models. Good agreement is shown with the in-core measurements when using analysis conditions expected to best represent this region, such as an assembly-specific axial power distribution. However, the use of these conditions to evaluate dosimetry in the fuel plenum region can lead to significant underestimation of the fluence. The use of a flat axial power distribution, however, does not underestimate the fluence in the fuel plenum region.

  6. Evaluation of storing Shippingport Core II spent blanket fuel assemblies in the T Plant PWR Core II fuel pool without active cooling

    SciTech Connect

    Gilbert, E.R.; Lanning, D.D.; Dana, C.M.; Hedengren, D.C.

    1994-10-01

    PWR Core II fuel pool chiller-off test was conducted because it appeared possible that acceptable pool-water temperatures could be maintained without operating the chillers, thus saving hundreds of thousands of dollars in maintenance and replacement costs. Test results showed that the water-cooling capability is no longer needed to maintain pool temperature below 38{degrees}C (100{degrees}F).

  7. Measurement and Analysis of Structural Integrity of Reactor Core Support Structure in Pressurized Water Reactor (PWR) Plant

    NASA Astrophysics Data System (ADS)

    Ansari, Saleem A.; Haroon, Muhammad; Rashid, Atif; Kazmi, Zafar

    2017-02-01

    Extensive calculation and measurements of flow-induced vibrations (FIV) of reactor internals were made in a PWR plant to assess the structural integrity of reactor core support structure against coolant flow. The work was done to meet the requirements of the Fukushima Response Action Plan (FRAP) for enhancement of reactor safety, and the regulatory guide RG-1.20. For the core surveillance measurements the Reactor Internals Vibration Monitoring System (IVMS) has been developed based on detailed neutron noise analysis of the flux signals from the four ex-core neutron detectors. The natural frequencies, displacement and mode shapes of the reactor core barrel (CB) motion were determined with the help of IVMS. The random pressure fluctuations in reactor coolant flow due to turbulence force have been identified as the predominant cause of beam-mode deflection of CB. The dynamic FIV calculations were also made to supplement the core surveillance measurements. The calculational package employed the computational fluid dynamics, mode shape analysis, calculation of power spectral densities of flow & pressure fields and the structural response to random flow excitation forces. The dynamic loads and stiffness of the Hold-Down Spring that keeps the core structure in position against upward coolant thrust were also determined by noise measurements. Also, the boron concentration in primary coolant at any time of the core cycle has been determined with the IVMS.

  8. Computational methods and implementation of the 3-D PWR core dynamics SIMTRAN code for online surveillance and prediction

    SciTech Connect

    Aragones, J.M.; Ahnert, C.

    1995-12-31

    New computational methods have been developed in our 3-D PWR core dynamics SIMTRAN code for online surveillance and prediction. They improve the accuracy and efficiency of the coupled neutronic-thermalhydraulic solution and extend its scope to provide, mainly, the calculation of: the fission reaction rates at the incore mini-detectors; the responses at the excore detectors (power range); the temperatures at the thermocouple locations; and the in-vessel distribution of the loop cold-leg inlet coolant conditions in the reflector and core channels, and to the hot-leg outlets per loop. The functional capabilities implemented in the extended SIMTRAN code for online utilization include: online surveillance, incore-excore calibration, evaluation of peak power factors and thermal margins, nominal update and cycle follow, prediction of maneuvers and diagnosis of fast transients and oscillations. The new code has been installed at the Vandellos-II PWR unit in Spain, since the startup of its cycle 7 in mid-June, 1994. The computational implementation has been performed on HP-700 workstations under the HP-UX Unix system, including the machine-man interfaces for online acquisition of measured data and interactive graphical utilization, in C and X11. The agreement of the simulated results with the measured data, during the startup tests and first months of actual operation, is well within the accuracy requirements. The performance and usefulness shown during the testing and demo phase, to be extended along this cycle, has proved that SIMTRAN and the man-machine graphic user interface have the qualities for a fast, accurate, user friendly, reliable, detailed and comprehensive online core surveillance and prediction.

  9. Analysis of a rod withdrawal in a PWR core with the neutronic- thermalhydraulic coupled code RELAP/PARCS and RELAP/VALKIN

    SciTech Connect

    Miro, R.; Maggini, F.; Barrachina, T.; Verdu, G.; Gomez, A.; Ortego, A.; Murillo, J. C.

    2006-07-01

    The Reactor Ejection Accident (REA) belongs to the Reactor Initiated Accidents (RIA) category of accidents and it is part of the licensing basis accident analyses required for pressure water reactors (PWR). The REA at hot zero power (HZP) is characterized by a single rod ejection from a core position with a very low power level. The evolution consists basically of a continuous reactivity insertion. The main feature limiting the consequences of the accident in a PWR is the Doppler Effect. To check the performance of the coupled code RELAP5/PARCS2.5 and RELAP5/VALKIN a REA in Trillo NPP is simulated. These analyses will allow knowing more accurately the PWR real plant phenomenology in the RIA most limiting conditions. (authors)

  10. Generalized Thermohydraulics Module GENFLO for Combining With the PWR Core Melting Model, BWR Recriticality Neutronics Model and Fuel Performance Model

    SciTech Connect

    Miettinen, Jaakko; Hamalainen, Anitta; Pekkarinen, Esko

    2002-07-01

    Thermal hydraulic simulation capability for accident conditions is needed at present in VTT in several programs. Traditional thermal hydraulic models are too heavy for simulation in the analysis tasks, where the main emphasis is the rapid neutron dynamics or the core melting. The GENFLO thermal hydraulic model has been developed at VTT for special applications in the combined codes. The basic field equations in GENFLO are for the phase mass, the mixture momentum and phase energy conservation equations. The phase separation is solved with the drift flux model. The basic variables to be solved are the pressure, void fraction, mixture velocity, gas enthalpy, liquid enthalpy, and concentration of non-condensable gas fractions. The validation of the thermohydraulic solution alone includes large break LOCA reflooding experiments and in specific for the severe accident conditions QUENCH tests. In the recriticality analysis the core neutronics is simulated with a two-dimensional transient neutronics code TWODIM. The recriticality with one rapid prompt peak is expected during a severe accident scenario, where the control rods have been melted and ECCS reflooding is started after the depressurization. The GENFLO module simulates the BWR thermohydraulics in this application. The core melting module has been developed for the real time operator training by using the APROS engineering simulators. The core heatup, oxidation, metal and fuel pellet relocation and corium pool formation into the lower plenum are calculated. In this application the GENFLO model simulates the PWR vessel thermohydraulics. In the fuel performance analysis the fuel rod transient behavior is simulated with the FRAPTRAN code. GENFLO simulates the subchannel around a single fuel rod and delivers the heat transfer on the cladding surface for the FRAPTRAN. The transient boundary conditions for the subchannel are transmitted from the system code for operational transient, loss of coolant accidents and

  11. Best estimate plus uncertainty analysis of departure from nucleate boiling limiting case with CASL core simulator VERA-CS in response to PWR main steam line break event

    SciTech Connect

    Brown, Cameron S.; Zhang, Hongbin; Kucukboyaci, Vefa; Sung, Yixing

    2016-09-07

    VERA-CS (Virtual Environment for Reactor Applications, Core Simulator) is a coupled neutron transport and thermal-hydraulics subchannel code under development by the Consortium for Advanced Simulation of Light Water Reactors (CASL). VERA-CS was used to simulate a typical pressurized water reactor (PWR) full core response with 17x17 fuel assemblies for a main steam line break (MSLB) accident scenario with the most reactive rod cluster control assembly stuck out of the core. The accident scenario was initiated at the hot zero power (HZP) at the end of the first fuel cycle with return to power state points that were determined by a system analysis code and the most limiting state point was chosen for core analysis. The best estimate plus uncertainty (BEPU) analysis method was applied using Wilks’ nonparametric statistical approach. In this way, 59 full core simulations were performed to provide the minimum departure from nucleate boiling ratio (MDNBR) at the 95/95 (95% probability with 95% confidence level) tolerance limit. The results show that this typical PWR core remains within MDNBR safety limits for the MSLB accident.

  12. Best estimate plus uncertainty analysis of departure from nucleate boiling limiting case with CASL core simulator VERA-CS in response to PWR main steam line break event

    DOE PAGES

    Brown, Cameron S.; Zhang, Hongbin; Kucukboyaci, Vefa; ...

    2016-09-07

    VERA-CS (Virtual Environment for Reactor Applications, Core Simulator) is a coupled neutron transport and thermal-hydraulics subchannel code under development by the Consortium for Advanced Simulation of Light Water Reactors (CASL). VERA-CS was used to simulate a typical pressurized water reactor (PWR) full core response with 17x17 fuel assemblies for a main steam line break (MSLB) accident scenario with the most reactive rod cluster control assembly stuck out of the core. The accident scenario was initiated at the hot zero power (HZP) at the end of the first fuel cycle with return to power state points that were determined by amore » system analysis code and the most limiting state point was chosen for core analysis. The best estimate plus uncertainty (BEPU) analysis method was applied using Wilks’ nonparametric statistical approach. In this way, 59 full core simulations were performed to provide the minimum departure from nucleate boiling ratio (MDNBR) at the 95/95 (95% probability with 95% confidence level) tolerance limit. The results show that this typical PWR core remains within MDNBR safety limits for the MSLB accident.« less

  13. Liquid level, void fraction, and superheated steam sensor for nuclear-reactor cores. [PWR; BWR

    DOEpatents

    Tokarz, R.D.

    1981-10-27

    This disclosure relates to an apparatus for monitoring the presence of coolant in liquid or mixed liquid and vapor, and superheated gaseous phases at one or more locations within an operating nuclear reactor core, such as pressurized water reactor or a boiling water reactor.

  14. Gamma-thermometer-based reactor-core liquid-level detector. [PWR

    SciTech Connect

    Burns, T.J.

    1981-06-16

    A system is provided which employs a modified gamma thermometer for determining the liquid coolant level within a nuclear reactor core. The gamma thermometer which normally is employed to monitor local core heat generation rate (reactor power), is modified by thermocouple junctions and leads to obtain an unambiguous indication of the presence or absence of coolant liquid at the gamma thermometer location. A signal processor generates a signal based on the thermometer surface heat transfer coefficient by comparing the signals from the thermocouples at the thermometer location. The generated signal is a direct indication of loss of coolant due to the change in surface heat transfer when coolant liquid drops below the thermometer location. The loss of coolant indication is independent of reactor power at the thermometer location. Further, the same thermometer may still be used for the normal power monitoring function.

  15. Core-concrete molten pool dynamics and interfacial heat transfer. [PWR; BWR

    SciTech Connect

    Benjamin, A.S.

    1980-01-01

    Theoretical models are derived for the heat transfer from molten oxide pools to an underlying concrete surface and from molten steel pools to a general concrete containment. To accomplish this, two separate effects models are first developed, one emphasizing the vigorous agitation of the molten pool by gases evolving from the concrete and the other considering the insulating effect of a slag layer produced by concrete melting. The resulting algebraic expressions, combined into a general core-concrete heat transfer representation, are shown to provide very good agreement with experiments involving molten steel pours into concrete crucibles.

  16. Weapons-Grade Plutonium-Thorium PWR Assembly Design and Core Safety Analysis

    SciTech Connect

    Dziadosz, David; Ake, Timothy N.; Saglam, Mehmet; Sapyta, Joe J.

    2004-07-15

    A light water reactor (LWR) fuel assembly design consisting of a blend of weapons-grade plutonium and natural thorium oxides was examined. The design meets current thermal-hydraulic and safety criteria. Such an assembly would have enough reactivity to achieve three cycles of operation. The pin power distribution indicates a fairly level distribution across the assembly, avoiding hot spots near guide tubes, corners, and other sections where excessive power would create significant loss to thermal-hydraulic margins.This work examined a number of physics and core safety analysis parameters that impact the operation and safety of power reactors. Such parameters as moderator coefficients of reactivity, Doppler coefficients, soluble boron worth, control rod worth, prompt neutron lifetime, and delayed-neutron fractions were considered. These in turn were used to examine reactor behavior during a number of operational conditions, transients, and accidents. Such conditions as shutdown from power with one rod stuck out, steam-line break accident, feedwater line break, loss of coolant flow, locked rotor accidents, control rod ejection accidents, and anticipated transients without scram (ATWSs) were examined.The analysis of selected reactor transients demonstrated that it is feasible to license and safely operate a reactor fueled with plutonium-thorium blended fuel. In most cases analyzed, the thorium mixture had less-severe consequences than those for a core comprising low-enriched uranium fuel. In the analyzed cases where the consequences were more severe, they were still within acceptable limits. The ATWS accident condition requires more analysis.

  17. Dosimetry assessments for the reactor pressure vessel and core barrel in UK PWR plant

    SciTech Connect

    Thornton, D.A.; Allen, D.A.; Huggon, A.P.; Picton, D.J.; Robinson, A.T.; Steadman, R.J.; Seren, T.; Lipponen, M.; Kekki, T.

    2011-07-01

    Specimens for the Sizewell B reactor pressure vessel (RPV) inservice steels surveillance program are irradiated inside eight capsules located within the reactor pressure vessel and loaded prior to commissioning. The periodic removal of these capsules and testing of their contents provides material properties data at intervals during the lifetime of the plant. Neutron activation measurements and radiation transport calculations play an essential role in assessing the neutron exposure of the specimens and RPV. Following the most recent withdrawal, seven capsules have now been removed covering nine cycles of reactor operation. This paper summarizes the dosimetry results of the Sizewell B surveillance program obtained to date. In addition to an overview of the calculational methodology it includes a review of the measurements. Finally, it describes an extension of the methodology to provide dosimetry recommendations for the core barrel and briefly discusses the results that were obtained. (authors)

  18. Performance of Core Exit Thermocouple for PWR Accident Management Action in Vessel Top Break LOCA Simulation Experiment at OECD/NEA ROSA Project

    NASA Astrophysics Data System (ADS)

    Suzuki, Mitsuhiro; Takeda, Takeshi; Nakamura, Hideo

    Presented are experiment results of the Large Scale Test Facility (LSTF) conducted at the Japan Atomic Energy Agency (JAEA) with a focus on core exit thermocouple (CET) performance to detect core overheat during a vessel top break loss-of-coolant accident (LOCA) simulation experiment. The CET temperatures are used to start accident management (AM) action to quickly depressurize steam generator (SG) secondary side in case of core temperature excursion. Test 6-1 is the first test of the OECD/NEA ROSA Project started in 2005, simulating withdraw of a control rod drive mechanism penetration nozzle at the vessel top head. The break size is equivalent to 1.9% cold leg break. The AM action was initiated when CET temperature rose up to 623K. There was no reflux water fallback onto the CETs during the core heat-up period. The core overheat, however, was detected with a time delay of about 230s. In addition, a large temperature discrepancy was observed between the CETs and the hottest core region. This paper clarifies the reasons of time delay and temperature discrepancy between the CETs and heated core during boil-off including three-dimensional steam flows in the core and core exit. The paper discusses applicability of the LSTF CET performance to pressurized water reactor (PWR) conditions and a possibility of alternative indicators for earlier AM action than in Test 6-1 is studied by using symptom-based plant parameters such as a reactor vessel water level detection.

  19. Development code for sensitivity and uncertainty analysis of input on the MCNPX for neutronic calculation in PWR core

    NASA Astrophysics Data System (ADS)

    Hartini, Entin; Andiwijayakusuma, Dinan

    2014-09-01

    This research was carried out on the development of code for uncertainty analysis is based on a statistical approach for assessing the uncertainty input parameters. In the butn-up calculation of fuel, uncertainty analysis performed for input parameters fuel density, coolant density and fuel temperature. This calculation is performed during irradiation using Monte Carlo N-Particle Transport. The Uncertainty method based on the probabilities density function. Development code is made in python script to do coupling with MCNPX for criticality and burn-up calculations. Simulation is done by modeling the geometry of PWR terrace, with MCNPX on the power 54 MW with fuel type UO2 pellets. The calculation is done by using the data library continuous energy cross-sections ENDF / B-VI. MCNPX requires nuclear data in ACE format. Development of interfaces for obtaining nuclear data in the form of ACE format of ENDF through special process NJOY calculation to temperature changes in a certain range.

  20. Facing Challenges for Monte Carlo Analysis of Full PWR Cores : Towards Optimal Detail Level for Coupled Neutronics and Proper Diffusion Data for Nodal Kinetics

    NASA Astrophysics Data System (ADS)

    Nuttin, A.; Capellan, N.; David, S.; Doligez, X.; El Mhari, C.; Méplan, O.

    2014-06-01

    Safety analysis of innovative reactor designs requires three dimensional modeling to ensure a sufficiently realistic description, starting from steady state. Actual Monte Carlo (MC) neutron transport codes are suitable candidates to simulate large complex geometries, with eventual innovative fuel. But if local values such as power densities over small regions are needed, reliable results get more difficult to obtain within an acceptable computation time. In this scope, NEA has proposed a performance test of full PWR core calculations based on Monte Carlo neutron transport, which we have used to define an optimal detail level for convergence of steady state coupled neutronics. Coupling between MCNP for neutronics and the subchannel code COBRA for thermal-hydraulics has been performed using the C++ tool MURE, developed for about ten years at LPSC and IPNO. In parallel with this study and within the same MURE framework, a simplified code of nodal kinetics based on two-group and few-point diffusion equations has been developed and validated on a typical CANDU LOCA. Methods for the computation of necessary diffusion data have been defined and applied to NU (Nat. U) and Th fuel CANDU after assembly evolutions by MURE. Simplicity of CANDU LOCA model has made possible a comparison of these two fuel behaviours during such a transient.

  1. On the effect of accident conditions on the molten core debris relocation into lower head of a PWR vessel

    NASA Astrophysics Data System (ADS)

    An, Xuegao

    From 1975 to present, it has been found that the primary risk to the public health and safety from nuclear power reactors lies in ``beyond design basis'' accidents. During such severe accidents, melting of the reactor core may lead to a loss of primary system integrity, or even containment failure, which will allow escape of significant amounts of radioactive material to the environment. It is very important to understand the mechanism of reactor core degradation during a severe accident. In this study, the damage progression of the reactor core and the slumping mechanism of molten material to the lower head of the reactor vessel were examined through simulation of severe accident scenarios that lead to large-scale core damage. The calculations were carried out using the computer code SCDAP/RELAP5. Different modeling parameters or models were used in calculations by version MOD3.2. The cladding oxidation shell ``durability'' parameter, which can control the timing of fuel clad failure, was varied. The heat flux model of steady-state natural convection of the molten pool was changed. The ultimate strength of the crust supporting the molten pool was doubled. These changes were made to examine the effects on the calculated core damage, and the molten pool expansion and its slumping. Different accident scenarios were simulated. The HPI/makeup flow rates were changed. The timing of opening and closing the PORV was considered. Reflood by restart of coolant pump 2B was also studied. Finally, the size of the PORV opening was also changed. The effects of these accident scenarios on accident progression and core damage process were studied. From the calculated results, it was concluded that the accurate modeling of core damage phenomena was very important to the prediction of the later stage of an accident. According to code MOD3.2, the molten material in a pool slumped to the lower head of the reactor vessel when the juncture of the top and side crusts failed after the

  2. Impact of boron dilution accidents on low boron PWR safety

    SciTech Connect

    Papukchiev, A.; Liu, Y.; Schaefer, A.

    2006-07-01

    In conventional pressurized water reactor (PWR) designs, soluble boron is used for reactivity control over core fuel cycle. As an inadvertent reduction of the boron concentration during a boron dilution accident could introduce positive reactivity and have a negative impact on PWR safety, design changes to reduce boron concentration in the reactor coolant are of general interest. In the framework of an investigation into the feasibility of low boron design, a PWR core configuration based on fuel with higher gadolinium (Gd) load has been developed which permits to reduce the natural boron concentration at begin of cycle (BOC) to 518 ppm. For the assessment of the potential safety advantages, a boron dilution accident due to small break loss-of-coolant-accident (SBLOCA) has been simulated with the system code ATHLET for two PWR core designs: a low boron design and a standard core design. The results from the comparative analyses showed that the impact of the boron dilution accident on the new PWR design safety is significantly lower in comparison with the standard design. The new reactor design provided at least 4, 4% higher reactivity margin to recriticality during the whole accident which is equivalent to the negative reactivity worth of additional 63% of all control rods fully inserted in to the core. (authors)

  3. PWR-GALE. PWR Effluent Radioactivity Releases

    SciTech Connect

    Willis, C.A.

    1992-01-13

    PWR-GALE calculates the expected annual releases of radioactive materials in gaseous and liquid effluents from pressurized light water reactors (PWRs). The calculations are based on data generated from operating reactors, field and laboratory tests, and plant-specific considerations incorporated to reduce the quantity of radioactive materials that may be released to the environment during normal operation including anticipated operational occurrences. PWR-GALE consists of two program, PGALEGS and PGALELQ. PGALEGS calculates the releases of radioactive materials (noble gases, radioactive particulates, carbon-14, tritium, argon-41, and iodine) in gaseous effluents from the waste gas processing system, steam generator blowdown system, condenser air ejector exhaust, containment purge exhaust, ventilation exhaust air from the auxiliary and turbine buildings and the spent fuel area, and steam leakage from the secondary system. PGALELQ calculates the releases of radioactive materials in liquid effluents from processed water generated from the boron recovery system to maintain plant water balance or for tritium control; processed liquid waste discharged from the waste systems, steam generator blowdown treatment system, and that discharged from the chemical waste and condensate demineralizer regeneration system; liquid waste discharged from the turbine building floor drain sumps; and detergent waste.

  4. WRAP-PWR verification studies

    SciTech Connect

    Gregory, M V; Ames, P L; Beranek, F; Kuehn, N H; Parks, P B

    1980-01-01

    A modular computational system known as the Water Reactor Analysis Package - Evaluation Model (WRAP-EM) was developed for the Nuclear Regulatory Commission (NRC) to interpret and evaluate reactor vendor EM methods and computed results. A subset of the system (WRAP-PWR-EM) provides the computational tools to perform a complete analysis of loss-of-coolant accidents (LOCA's) in pressurized water reactors (PWR's). A set of calculations modeling experimental tests in the Semiscale and LOFT facilities, and calculations of a large break in a typical four-loop Westinghouse PWR plant have verified that the WRAP-PWR-EM system is functioning as intended.

  5. Loss of Coolant Accident (LOCA) / Emergency Core Coolant System (ECCS Evaluation of Risk-Informed Margins Management Strategies for a Representative Pressurized Water Reactor (PWR)

    SciTech Connect

    Szilard, Ronaldo Henriques

    2016-09-01

    A Risk Informed Safety Margin Characterization (RISMC) toolkit and methodology are proposed for investigating nuclear power plant core, fuels design and safety analysis, including postulated Loss-of-Coolant Accident (LOCA) analysis. This toolkit, under an integrated evaluation model framework, is name LOCA toolkit for the US (LOTUS). This demonstration includes coupled analysis of core design, fuel design, thermal hydraulics and systems analysis, using advanced risk analysis tools and methods to investigate a wide range of results.

  6. Characterization of Decommissioned PWR Vessel Internals Material Samples: Tensile and SSRT Testing (Nonproprietary Version)

    SciTech Connect

    M.Krug, R.Shogan

    2004-09-01

    Pressurized water reactor (PWR) cores operate under extreme environmental conditions due to coolant chemistry, operating temperature, and neutron exposure. Extending the life of PWRs requires detailed knowledge of the changes in mechanical and corrosion properties of the structural austenitic stainless steel components adjacent to the fuel (internals) subjected to such conditions. This project studied the effects of reactor service on the mechanical and corrosion properties of samples of baffle plate, former plate, and core barrel from a decommissioned PWR.

  7. Design of Recycle PWR with Heavy Water Moderation

    SciTech Connect

    Hibi, K.; Uchita, M.

    2002-07-01

    This study shows the conceptual plant design of the recycle PWR (RPWR), which is an innovative MOX-PWR with breeding ratios around 1.1 moderated by heavy water. Most of the plant systems of RPWR can employ the systems of PWRs. RPWR has no acid boron systems and has a small tritium removal system. The construction and operation costs are similar to the current PWRs. While, heavy water cost will be decreased drastically with up-to-date producing methods. The reliability for the plant systems of RPWR is high and R and D cost for realizing RPWR is very low because the core design of RPWR is fundamentally based on the current PWR technology. (authors)

  8. Characterization of Decommissioned PWR Vessel Internals Materials Samples: Material Certification, Fluence, and Temperature (Nonproprietary Version)

    SciTech Connect

    M. Krug; R. Shogan; A. Fero; M. Snyder

    2004-11-01

    Pressurized water reactor (PWR) cores, operate under extreme environmental conditions due to coolant chemistry, operating temperature, and neutron exposure. Extending the life of PWRs require detailed knowledge of the changes in mechanical and corrosion properties of the structural austenitic stainless steel components adjacent to the fuel. This report contains basic material characterization information of the as-installed samples of reactor internals material which were harvested from a decommissioned PWR.

  9. Identification and evaluation of PWR in-vessel severe accident management strategies

    SciTech Connect

    Dukelow, J S; Harrison, D G; Morgenstern, M

    1992-03-01

    This reports documents work performed the NRC/RES Accident Management Guidance Program to evaluate possible strategies for mitigating the consequences of PWR severe accidents. The selection and evaluation of strategies was limited to the in-vessel phase of the severe accident, i.e., after the initiation of core degradation and prior to RPV failure. A parallel project at BNL has been considering strategies applicable to the ex-vessel phase of PWR severe accidents.

  10. PWR AXIAL BURNUP PROFILE ANALYSIS

    SciTech Connect

    J.M. Acaglione

    2003-09-17

    The purpose of this activity is to develop a representative ''limiting'' axial burnup profile for pressurized water reactors (PWRs), which would encompass the isotopic axial variations caused by different assembly irradiation histories, and produce conservative isotopics with respect to criticality. The effect that the low burnup regions near the ends of spent fuel have on system reactivity is termed the ''end-effect''. This calculation will quantify the end-effects associated with Pressurized Water Reactor (PWR) fuel assemblies emplaced in a hypothetical 21 PWR waste package. The scope of this calculation covers an initial enrichment range of 3.0 through 5.0 wt% U-235 and a burnup range of 10 through 50 GWd/MTU. This activity supports the validation of the process for ensuring conservative generation of spent fuel isotopics with respect to criticality safety applications, and the use of burnup credit for commercial spent nuclear fuel. The intended use of these results will be in the development of PWR waste package loading curves, and applications involving burnup credit. Limitations of this evaluation are that the limiting profiles are only confirmed for use with the B&W 15 x 15 fuel assembly design. However, this assembly design is considered bounding of all other typical commercial PWR fuel assembly designs. This calculation is subject to the Quality Assurance Requirements and Description (QARD) because this activity supports investigations of items or barriers on the Q-list (YMP 2001).

  11. FLUOLE-2: An Experiment for PWR Pressure Vessel Surveillance

    NASA Astrophysics Data System (ADS)

    Thiollay, Nicolas; Di Salvo, Jacques; Sandrin, Charlotte; Soldevila, Michel; Bourganel, Stéphane; Fausser, Clément; Destouches, Christophe; Blaise, Patrick; Domergue, Christophe; Philibert, Hervé; Bonora, Jonathan; Gruel, Adrien; Geslot, Benoit; Lamirand, Vincent; Pepino, Alexandra; Roche, Alain; Méplan, Olivier; Ramdhane, Mourad

    2016-02-01

    FLUOLE-2 is a benchmark-type experiment dedicated to 900 and 1450 MWe PWR vessels surveillance dosimetry. This two-year program started in 2014 and will end in 2015. It will provide precise experimental data for the validation of the neutron spectrum propagation calculation from core to vessel. It is composed of a square core surrounded by a stainless steel baffe and internals: PWR barrel is simulated by steel structures leading to different steel-water slides; two steel components stand for a surveillance capsule holder and for a part of the pressure vessel. Measurement locations are available on the whole experimental structure. The experimental knowledge of core sources will be obtained by integral gamma scanning measurements directly on fuel pins. Reaction rates measured by calibrated fission chambers and a large set of dosimeters will give information on the neutron energy and spatial distributions. Due to the low level neutron flux of EOLE ZPR a special, high efficiency, calibrated gamma spectrometry device will be used for some dosimeters, allowing to measure an activity as low as 7. 10-2 Bq per sample. 103mRh activities will be measured on an absolute calibrated X spectrometry device. FLUOLE-2 experiment goal is to usefully complete the current experimental benchmarks database used for the validation of neutron calculation codes. This two-year program completes the initial FLUOLE program held in 2006-2007 in a geometry representative of 1300 MWe PWR.

  12. Design study of long-life PWR using thorium cycle

    SciTech Connect

    Subkhi, Moh. Nurul; Su'ud, Zaki; Waris, Abdul

    2012-06-06

    Design study of long-life Pressurized Water Reactor (PWR) using thorium cycle has been performed. Thorium cycle in general has higher conversion ratio in the thermal spectrum domain than uranium cycle. Cell calculation, Burn-up and multigroup diffusion calculation was performed by PIJ-CITATION-SRAC code using libraries based on JENDL 3.2. The neutronic analysis result of infinite cell calculation shows that {sup 231}Pa better than {sup 237}Np as burnable poisons in thorium fuel system. Thorium oxide system with 8%{sup 233}U enrichment and 7.6{approx} 8%{sup 231}Pa is the most suitable fuel for small-long life PWR core because it gives reactivity swing less than 1%{Delta}k/k and longer burn up period (more than 20 year). By using this result, small long-life PWR core can be designed for long time operation with reduced excess reactivity as low as 0.53%{Delta}k/k and reduced power peaking during its operation.

  13. PWR plant transient analyses using TRAC-PF1

    SciTech Connect

    Ireland, J.R.; Boyack, B.E.

    1984-01-01

    This paper describes some of the pressurized water reactor (PWR) transient analyses performed at Los Alamos for the US Nuclear Regulatory Commission using the Transient Reactor Analysis Code (TRAC-PF1). Many of the transient analyses performed directly address current PWR safety issues. Included in this paper are examples of two safety issues addressed by TRAC-PF1. These examples are pressurized thermal shock (PTS) and feed-and-bleed cooling for Oconee-1. The calculations performed were plant specific in that details of both the primary and secondary sides were modeled in addition to models of the plant integrated control systems. The results of these analyses show that for these two transients, the reactor cores remained covered and cooled at all times posing no real threat to the reactor system nor to the public.

  14. Estimating probable flaw distributions in PWR steam generator tubes

    SciTech Connect

    Gorman, J.A.; Turner, A.P.L.

    1997-02-01

    This paper describes methods for estimating the number and size distributions of flaws of various types in PWR steam generator tubes. These estimates are needed when calculating the probable primary to secondary leakage through steam generator tubes under postulated accidents such as severe core accidents and steam line breaks. The paper describes methods for two types of predictions: (1) the numbers of tubes with detectable flaws of various types as a function of time, and (2) the distributions in size of these flaws. Results are provided for hypothetical severely affected, moderately affected and lightly affected units. Discussion is provided regarding uncertainties and assumptions in the data and analyses.

  15. PWR representative behavior during a LOCA

    SciTech Connect

    Allison, C.M.

    1981-01-01

    To date, there has been substantial analytical and experimental effort to define the margins between design basis loss-of-coolant accident (LOCA) behavior and regulatory limits on maximum fuel rod cladding temperature and deformation. As a result, there is extensive documentation on the modeling of fuel rod behavior in test reactors and design basis LOCA's. However, modeling of that behavior using representative, non-conservative, operating histories is not nearly as well documented in the public literature. Therefore, the objective of this paper is (a) to present calculations of LOCA induced behavior for Pressurized Water Reactor (PWR) core representative fuel rods, and (b) to discuss the variability in those calculations given the variability in fuel rod condition at the initiation of the LOCA. This analysis was limited to the study of changes in fuel rod behavior due to different power operating histories. The other two important parameters which affect that behavior, initial fuel rod design and LOCA coolant conditions were held invarient for all of the representative rods analyzed.

  16. Study on Equilibrium Characteristics of Thorium-Plutonium-Minor Actinides Mixed Oxides Fuel in PWR

    SciTech Connect

    Waris, A.; Permana, S.; Kurniadi, R.; Su'ud, Z.; Sekimoto, H.

    2010-06-22

    A study on characteristics of thorium-plutonium-minor actinides utilization in the pressurized water reactor (PWR) with the equilibrium burnup model has been conducted. For a comprehensive evaluation, several fuel cycles scenario have been included in the present study with the variation of moderator-to-fuel volume ratio (MFR) of PWR core design. The results obviously exhibit that the neutron spectra grow to be harder with decreasing of the MFR. Moreover, the neutron spectra also turn into harder with the rising number of confined heavy nuclides. The required {sup 233}U concentration for criticality of reactor augments with the increasing of MFR for all heavy nuclides confinement and thorium and uranium confinement in PWR.

  17. Evaluation of surface modification techniques for PWR steam generator channel heads. Final report

    SciTech Connect

    Spalaris, C.N.

    1986-06-01

    Surface modification which were developed under a previous EPRI program and then applied to Boiling Water Reactor replacement piping, were modified for treating PWR steam generator channel head surfaces. Surface modifications have been shown to reduce out-of-core activity build up in BWR and thought to be equally effective in PWR circuits as well. Prototypical surface test specimens were used to develop techniques appropriate to PWR alloy substrates which were then applied to treat the surfaces of a spare, full size PWR channel head in a field demonstration. Modified surfaces cut from test specimens and pieces removed from the field demonstration were submitted to metallurgical investigations. No damage to the substrate alloys was detected as a result of the surface modification processes. Combination of mechanical and electropolishing action improved the as fabricated finish by at least a factor of 3 for the Inconel plate and factors of 20 for the stainless weld overlay. Field demonstration yielded a factor of 10 improvement in the weld overlay and 30 to 40% in the divider plate. Because these surfaces are known to be responsible for 57% of the area radioactivity in PWR steam generators in service, prepolishing is expected to reduce radiation fields substantially. 31 figs.

  18. Concept of Small Sized Integrated PWR with Double Pressure Vessels

    SciTech Connect

    Kinoshita, I.; Ueda, N.; Nishi, Y.; Matsumura, T.

    2002-07-01

    For early deployment of small sized nuclear reactors, it is better to reduce the BOP cost with new ideas than introducing innovative technologies for core, fuel and materials. In this report, a concept of the integrated, forced convective and small PWR with double pressure vessels has been proposed. The electric output of this reactor is 150 MW. Conventional technologies are adopted for core and fuel. Refueling, maintenance and repairing are made in a special ship with complete facilities and skilled experts. The pressure vessel with the core, control rod drive mechanisms (CRDM), main circulating pumps (MCP), steam generators (SG) and other reactor internals are transferred between the reactor building and the ship. Technical feasibility for safety and maintainability has been discussed qualitatively. The construction cost has been roughly estimated. (authors)

  19. A Study on the Conceptual Design of a 1,500 MWe Passive PWR with Annular Fuel

    SciTech Connect

    Kwi Lim Lee; Soon Heung Chang

    2004-07-01

    In this study, the preliminary conceptual design of a 1500 MWe pressurized water reactor (PWR) with annular fuel has been performed. This design is derived from the AP1000 which is a 1000 MWe PWR with two-loop. However, the present design is a 1500 MWe PWR with three-loop, passive safety features and extensive plant simplifications to enhance the construction, operation, and maintenance. The preliminary design parameters of this reactor have been determined through simple relation to those of AP1000 for reactor, reactor coolant system, and passive safety injection system. Using the MATRA code, we analyze the core designs for two alternatives on fuel assembly types: solid fuel and annular fuel. The performance of reactor cooling systems is evaluated through the accident of the cold leg break in the core makeup tank loop by using MARS2.1 code. This study presents the developmental strategy, preliminary design parameters and safety analysis results. (authors)

  20. MC21 analysis of the MIT PWR benchmark: Hot zero power results

    SciTech Connect

    Kelly Iii, D. J.; Aviles, B. N.; Herman, B. R.

    2013-07-01

    MC21 Monte Carlo results have been compared with hot zero power measurements from an operating pressurized water reactor (PWR), as specified in a new full core PWR performance benchmark from the MIT Computational Reactor Physics Group. Included in the comparisons are axially integrated full core detector measurements, axial detector profiles, control rod bank worths, and temperature coefficients. Power depressions from grid spacers are seen clearly in the MC21 results. Application of Coarse Mesh Finite Difference (CMFD) acceleration within MC21 has been accomplished, resulting in a significant reduction of inactive batches necessary to converge the fission source. CMFD acceleration has also been shown to work seamlessly with the Uniform Fission Site (UFS) variance reduction method. (authors)

  1. Subchannel analysis of multiple CHF events. [PWR; BWR

    SciTech Connect

    Reddy, D.G.; Fighetti, C.F.

    1982-08-01

    The phenomenon of multiple CHF events in rod bundle heat transfer tests, referring to the occurrence of CHF on more than one rod or at more than one location on one rod is examined. The adequacy of some of the subchannel CHF correlations presently used in the nuclear industry in predicting higher order CHF events is ascertained based on local coolant conditions obtained with the COBRA IIIC subchannel code. The rod bundle CHF data obtained at the Heat Transfer Research Facility of Columbia University are examined for multiple CHF events using a combination of statistical analyses and parametric studies. The above analyses are applied to the study of three data sets of tests simulating both PWR and BWR reactor cores with uniform and non-uniform axial heat flux distributions. The CHF correlations employed in this study include: (1) CE-1 correlation, (2) B and W-2 correlation, (3) W-3 correlation, and (4) Columbia correlation.

  2. TRANSPORT CHARACTERISTICS OF SELECTED PWR LOCA GENERATED DEBRIS.

    SciTech Connect

    A. K. MAJI; B. MARSHALL; ET AL

    2000-10-01

    In the unlikely event of a Loss of Coolant Accident (LOCA) in a pressurized water reactor (PWR), break jet impingement would dislodge thermal insulation from nearby piping, as well as other materials within the containment, such as paint chips, concrete dust, and fire barrier materials. Steam/water flows induced by the break and by the containment sprays would transport debris to the containment floor. Subsequently, debris would likely transport to and accumulate on the suction sump screens of the emergency core cooling system (ECCS) pumps, thereby potentially degrading ECCS performance and possibly even failing the ECCS. In 1998, the U. S. Nuclear Regulatory Commission (NRC) initiated a generic study (Generic Safety Issue-191) to evaluate the potential for the accumulation of LOCA related debris on the PWR sump screen and the consequent loss of ECCS pump net positive suction head (NPSH). Los Alamos National Laboratory (LANL), supporting the resolution of GSI-191, was tasked with developing a method for estimating debris transport in PWR containments to estimate the quantity of debris that would accumulate on the sump screen for use in plant specific evaluations. The analytical method proposed by LANL, to predict debris transport within the water that would accumulate on the containment floor, is to use computational fluid dynamics (CFD) combined with experimental debris transport data to predict debris transport and accumulation on the screen. CFD simulations of actual plant containment designs would provide flow data for a postulated accident in that plant, e.g., three-dimensional patterns of flow velocities and flow turbulence. Small-scale experiments would determine parameters defining the debris transport characteristics for each type of debris. The containment floor transport methodology will merge debris transport characteristics with CFD results to provide a reasonable and conservative estimate of debris transport within the containment floor pool and

  3. Horizontal Drop of 21- PWR Waste Package

    SciTech Connect

    A.K. Scheider

    2007-01-31

    The objective of this calculation is to determine the structural response of the waste package (WP) dropped horizontally from a specified height. The WP used for that purpose is the 21-Pressurized Water Reactor (PWR) WP. The scope of this document is limited to reporting the calculation results in-terms of stress intensities. This calculation is associated with the WP design and was performed by the Waste Package Design group in accordance with the ''Technical Work Plan for: Waste Package Design Description for LA'' (Ref. 16). AP-3.12Q, ''Calculations'' (Ref. 1 1) is used to perform the calculation and develop the document. The sketches attached to this calculation provide the potential dimensions and materials for the 21-PWR WP design.

  4. Conceptual design study of small long-life PWR based on thorium cycle fuel

    SciTech Connect

    Subkhi, M. Nurul; Su'ud, Zaki; Waris, Abdul; Permana, Sidik

    2014-09-30

    A neutronic performance of small long-life Pressurized Water Reactor (PWR) using thorium cycle based fuel has been investigated. Thorium cycle which has higher conversion ratio in thermal region compared to uranium cycle produce some significant of {sup 233}U during burn up time. The cell-burn up calculations were performed by PIJ SRAC code using nuclear data library based on JENDL 3.3, while the multi-energy-group diffusion calculations were optimized in whole core cylindrical two-dimension R-Z geometry by SRAC-CITATION. this study would be introduced thorium nitride fuel system which ZIRLO is the cladding material. The optimization of 350 MWt small long life PWR result small excess reactivity and reduced power peaking during its operation.

  5. Conceptual design study of small long-life PWR based on thorium cycle fuel

    NASA Astrophysics Data System (ADS)

    Subkhi, M. Nurul; Su'ud, Zaki; Waris, Abdul; Permana, Sidik

    2014-09-01

    A neutronic performance of small long-life Pressurized Water Reactor (PWR) using thorium cycle based fuel has been investigated. Thorium cycle which has higer conversion ratio in thermal region compared to uranium cycle produce some significant of 233U during burn up time. The cell-burn up calculations were performed by PIJ SRAC code using nuclear data library based on JENDL 3.3, while the multi-energy-group diffusion calculations were optimized in whole core cylindrical two-dimension R-Z geometry by SRAC-CITATION. this study would be introduced thorium nitride fuel system which ZIRLO is the cladding material. The optimization of 350 MWt small long life PWR result small excess reactivity and reduced power peaking during its operation.

  6. Optimization of small long-life PWR based on thorium fuel

    NASA Astrophysics Data System (ADS)

    Subkhi, Moh Nurul; Suud, Zaki; Waris, Abdul; Permana, Sidik

    2015-09-01

    A conceptual design of small long-life Pressurized Water Reactor (PWR) using thorium fuel has been investigated in neutronic aspect. The cell-burn up calculations were performed by PIJ SRAC code using nuclear data library based on JENDL 3.2, while the multi-energy-group diffusion calculations were optimized in three-dimension X-Y-Z geometry of core by COREBN. The excess reactivity of thorium nitride with ZIRLO cladding is considered during 5 years of burnup without refueling. Optimization of 350 MWe long life PWR based on 5% 233U & 2.8% 231Pa, 6% 233U & 2.8% 231Pa and 7% 233U & 6% 231Pa give low excess reactivity.

  7. Pressure-vessel-damage fluence reduction by low-leakage fuel management. [PWR

    SciTech Connect

    Cokinos, D.; Aronson, A.L.; Carew, J.F.; Kohut, P.; Todosow, M.; Lois, L.

    1983-01-01

    As a result of neutron-induced radiation damage to the pressure vessel and of an increased concern that in a PWR transient the pressure vessel may be subjected to pressurized thermal shock (PTS), detailed analyses have been undertaken to determine the levels of neutron fluence accumulation at the pressure vessels of selected PWR's. In addition, various methods intended to limit vessel damage by reducing the vessel fluence have been investigated. This paper presents results of the fluence analysis and the evaluation of the low-leakage fuel management fluence reduction method. The calculations were performed with DOT-3.5 in an octant of the core/shield/vessel configuration using a 120 x 43 (r, theta) mesh structure.

  8. Optimization of small long-life PWR based on thorium fuel

    SciTech Connect

    Subkhi, Moh Nurul; Suud, Zaki Waris, Abdul; Permana, Sidik

    2015-09-30

    A conceptual design of small long-life Pressurized Water Reactor (PWR) using thorium fuel has been investigated in neutronic aspect. The cell-burn up calculations were performed by PIJ SRAC code using nuclear data library based on JENDL 3.2, while the multi-energy-group diffusion calculations were optimized in three-dimension X-Y-Z geometry of core by COREBN. The excess reactivity of thorium nitride with ZIRLO cladding is considered during 5 years of burnup without refueling. Optimization of 350 MWe long life PWR based on 5% {sup 233}U & 2.8% {sup 231}Pa, 6% {sup 233}U & 2.8% {sup 231}Pa and 7% {sup 233}U & 6% {sup 231}Pa give low excess reactivity.

  9. Experience in PWR and BWR mixed-oxide fuel management

    SciTech Connect

    Schlosser, G.J.; Krebs, W.; Urban, P. )

    1993-04-01

    Germany has adopted the strategy of a closed fuel cycle using reprocessing and recycling. The central issue today is plutonium recycling by the use of U-Pu mixed oxide (MOX) in pressurized water reactors (PWRs) and boiling water reactors (BWRs). The design of MOX fuel assemblies and fuel management in MOX-containing cores are strongly influenced by the nuclear properties of the plutonium isotopes. Optimized MOX fuel assembly designs for PWRs currently use up to three types of MOX fuel rods having different plutonium contents with natural uranium or uranium tailings as carrier material but without burnable absorbers. The MOX fuel assembly designs for BWRs use four to six rod types with different plutonium contents and Gd[sub 2]O[sub 3]/UO[sub 2] burnable absorber rods. Both the PWR and the BWR designs attain good burnup equivalence and compatibility with uranium fuel assemblies. High flexibility exists in the loading schemes relative to the position and number of MOX fuel assemblies in the reloads and in the core as a whole. The Siemens experience with MOX fuel assemblies is based on the insertion of 318 MOX fuel assemblies in eight PWRs and 168 in BWRs and pressurized heavy water reactors so far. The primary operating results include information on the cycle length, power distribution, reactivity coefficients, and control rod worth of cores containing MOX fuel assemblies.

  10. Analysis of the return to power scenario following a LBLOCA in a PWR

    SciTech Connect

    Macian, R.; Tyler, T.N.; Mahaffy, J.H.

    1995-09-01

    The risk of reactivity accidents has been considered an important safety issue since the beginning of the nuclear power industry. In particular, several events leading to such scenarios for PWR`s have been recognized and studied to assess the potential risk of fuel damage. The present paper analyzes one such event: the possible return to power during the reflooding phase following a LBLOCA. TRAC-PF1/MOD2 coupled with a three-dimensional neutronic model of the core based on the Nodal Expansion Method (NEM) was used to perform the analysis. The system computer model contains a detailed representation of a complete typical 4-loop PWR. Thus, the simulation can follow complex system interactions during reflooding, which may influence the neutronics feedback in the core. Analyses were made with core models bases on cross sections generated by LEOPARD. A standard and a potentially more limiting case, with increased pressurizer and accumulator inventories, were run. In both simulations, the reactor reaches a stable state after the reflooding is completed. The lower core region, filled with cold water, generates enough power to boil part of the incoming liquid, thus preventing the core average liquid fraction from reaching a value high enough to cause a return to power. At the same time, the mass flow rate through the core is adequate to maintain the rod temperature well below the fuel damage limit.

  11. Analytical description of PWR pressurizer transients. Final report

    SciTech Connect

    Ahl, J.P.

    1985-03-01

    Simulating the complicated physical processes that occur in a PWR pressurizer during a transient presented a considerable challenge to modelers. The computer code developed and validated in this study will help utilities to better understand both the behavior of the pressurizer and the overall performance of a PWR after a loss-of-coolant accident.

  12. Improving fuel-rod performance. [PWR; BWR

    SciTech Connect

    Ocken, H.; Knott, S.

    1981-03-01

    To reduce the risk of fuel-rod failures, utilities operate their nuclear reactors within conservative limits on power increases proposed by nuclear-fuel vendors. Of particular concern to US utilities is that adopting these limits results in an industrywide average plant capacity loss of 3% in BWR designs and 0.3% in PWR designs. To replace lost BWR capacity by other generating means currently costs the utilities $150 million annually, and losses for PWRs are about $20 million. Efforts are therefore being made to identify the factors responsible for Zircaloy degradation under PCI condition and to improve nuclear-fuel-rod design and reactor operation.

  13. A Feasibility Study of an Integral PWR for Space Applications

    SciTech Connect

    Grandis, S. De; Finzi, E.; Lombardi, C.V.; Mandelli, D.; Padovani, E.; Passoni, M.; Ricotti, M.E.; Santini, L.

    2004-07-01

    Fission space power systems are well suited to provide safe, reliable, economic and robust energy sources, in the order of 100 KWe. A preliminary feasibility study of a nuclear fission reactor is here presented with the following requirements: i) high reliability, ii) R and D program of moderate cost, iii) to be deployed within a reasonable period of time (e.g. 2015), iv) to be operated and controlled for a long time (10 years) without human intervention, v) possibly to be also used as a byproduct for some particular terrestrial application (or at least to share common technologies), vi) to start with stationary application. The driving idea is to extend as much as possible the PWR technology, by recurring to an integral type reactor. Two options are evaluated for the electricity production: a Rankine steam cycle and a Rankine organic fluid cycle. The neutronics calculation is based on WIMS code benchmarked with MCNP code. The reactivity control is envisaged by changing the core geometry. The resulting system appears viable and of reasonable size, well fit to the present space vector capabilities. Finally, a set of R and D needs has been identified: cold well, small steam turbines, fluid leakage control, pumps, shielding, steam generator in low-gravity conditions, self pressurizer, control system. A R and D program of reasonable extent may yield the needed answers, and some demanding researches are of interest for the new generation Light Water Reactors. (authors)

  14. Scoping Study Investigating PWR Instrumentation during a Severe Accident Scenario

    SciTech Connect

    Rempe, J. L.; Knudson, D. L.; Lutz, R. J.

    2015-09-01

    The accidents at the Three Mile Island Unit 2 (TMI-2) and Fukushima Daiichi Units 1, 2, and 3 nuclear power plants demonstrate the critical importance of accurate, relevant, and timely information on the status of reactor systems during a severe accident. These events also highlight the critical importance of understanding and focusing on the key elements of system status information in an environment where operators may be overwhelmed with superfluous and sometimes conflicting data. While progress in these areas has been made since TMI-2, the events at Fukushima suggests that there may still be a potential need to ensure that critical plant information is available to plant operators. Recognizing the significant technical and economic challenges associated with plant modifications, it is important to focus on instrumentation that can address these information critical needs. As part of a program initiated by the Department of Energy, Office of Nuclear Energy (DOE-NE), a scoping effort was initiated to assess critical information needs identified for severe accident management and mitigation in commercial Light Water Reactors (LWRs), to quantify the environment instruments monitoring this data would have to survive, and to identify gaps where predicted environments exceed instrumentation qualification envelop (QE) limits. Results from the Pressurized Water Reactor (PWR) scoping evaluations are documented in this report. The PWR evaluations were limited in this scoping evaluation to quantifying the environmental conditions for an unmitigated Short-Term Station BlackOut (STSBO) sequence in one unit at the Surry nuclear power station. Results were obtained using the MELCOR models developed for the US Nuclear Regulatory Commission (NRC)-sponsored State of the Art Consequence Assessment (SOARCA) program project. Results from this scoping evaluation indicate that some instrumentation identified to provide critical information would be exposed to conditions that

  15. Calculation of the neutron source distribution in the VENUS PWR Mockup Experiment

    SciTech Connect

    Williams, M.L.; Morakinyo, P.; Kam, F.B.K.; Leenders, L.; Minsart, G.; Fabry, A.

    1984-01-01

    The VENUS PWR Mockup Experiment is an important component of the Nuclear Regulatory Commission's program goal of benchmarking reactor pressure vessel (RPV) fluence calculations in order to determine the accuracy to which RPV fluence can be computed. Of particular concern in this experiment is the accuracy of the source calculation near the core-baffle interface, which is the important region for contributing to RPV fluence. Results indicate that the calculated neutron source distribution within the VENUS core agrees with the experimental measured values with an average error of less than 3%, except at the baffle corner, where the error is about 6%. Better agreement with the measured fission distribution was obtained with a detailed space-dependent cross-section weighting procedure for thermal cross sections near the core-baffle interface region. The maximum error introduced into the predicted RPV fluence due to source errors should be on the order of 5%.

  16. Investigation of radial power and temperature effects in large-scale reflood experiments. [PWR

    SciTech Connect

    Motley, F.

    1983-01-01

    The largest reflood test facility in the world has been designed and constructed by the Japan Atomic Energy Research Institute (JAERI). The experimental test facility, known as the Cylindrical Core Test Facility (CCTF), models a full-height core section and the four primary loops of a Pressurized Water Reactor (PWR). The radial power distribution and temperature distribution were varied during the testing program. The test results indicate that the radial effects, while noticeable, do not appreciably alter the overall quenching behavior of the facility. The Transient Reactor Analysis Code (TRAC) correctly predicted the experimental results of several of the tests. The code results indicate that the core flow pattern adjusts multidimensionally to mitigate the effects of increased power or stored energy.

  17. Crevice chemistry control in PWR steam generators

    SciTech Connect

    Sawochka, S.G.; Choi, S.S.; Millett, P.J.; Bates, J.; Gardner, J.

    1995-12-31

    To establish a basis for predicting and eventually controlling crevice solution chemistry in PWR steam generators, hideout tests were performed at several units. Results indicated that impurity hideout rates varied with the species and with bulk water concentration. Field evaluations of crevice impurity inventory models based on the hideout rate data indicated that further model refinements were necessary, e.g., more frequent quantification of the relation of hideout rates and bulk water concentration. An alternate crevice inventory model based on a real-time mass balance approach also began to be pursued. Modeling results currently are being used at several PWRs to establish a chloride injection rate consistent with development of a near neutral crevice solution to minimize IGA/SCC. Hideout return data are being used to independently establish predictions of crevice chemistry and to substantiate the hideout rate and mass balance model predictions.

  18. Impact of radiation embrittlement on integrity of pressure vessel supports for two PWR (pressurized-water-reactor) plants

    SciTech Connect

    Cheverton, R.D.; Pennell, W.E.; Robinson, G.C.; Nanstad, R.K.

    1988-01-01

    Recent pressure-vessel surveillance data from the High Flux Isotope Reactor (HFIR) indicate an embrittlement fluence-rate effect that is applicable to the evaluation of the integrity of light-water reactor (LWR) pressure vessel supports. A preliminary evaluation using the HFIR data indicated increases in the nil ductility transition temperature at 32 effective full-power years (EFPY) of 100 to 130/degree/C for pressurized-water-reactor (PWR) vessel supports located in the cavity at midheight of the core. This result indicated a potential problem with regard to life expectancy. However, an accurate assessment required a detailed, specific-plant, fracture-mechanics analysis. After a survey and cursory evaluation of all LWR plants, two PWR plants that appeared to have a potential problem were selected. Results of the analyses indicate minimum critical flaw sizes small enough to be of concern before 32 EFPY. 24 refs., 16 figs., 7 tabs.

  19. Subchannel Thermal-Hydraulic Experimental Program (STEP). Volume 1. Mixing in a pressurized water reactor (PWR) rod bundle. Final report

    SciTech Connect

    Barber, A.R.; Zielke, L.A.

    1980-08-01

    This volume describes an experiment that was performed to determine the mixing characteristics of a pressurized water reactor (PWR) rod bundle. The objective of this project was to improve the subchannel computer code models of the reactor core. The experimental technique was isokinetic subchannel withdrawal of the entire flow from two sample subchannels. Once withdrawn, the sample fluid was condensed and its enthalpy was measured by regenerative heat exchange calorimetry. The test bundle was a 4 x 6 electrically heated array with a 50% power upset. The COBRA IIIC code was used to model the experiment and to determine the value of the thermal mixing coefficient, ..beta.., that was necessary to predict the measured results. Both single- and two-phase data were obtained over a range of PWR operating conditions. The results indicate that both single- and two-phase mixing is small. The COBRA model predicts the enthalpy data using a turbulent mixing coefficient, ..beta.. approx. = 0.002.

  20. A PWR Thorium Pin Cell Burnup Benchmark

    SciTech Connect

    Weaver, Kevan Dean; Zhao, X.; Pilat, E. E; Hejzlar, P.

    2000-05-01

    As part of work to evaluate the potential benefits of using thorium in LWR fuel, a thorium fueled benchmark comparison was made in this study between state-of-the-art codes, MOCUP (MCNP4B + ORIGEN2), and CASMO-4 for burnup calculations. The MOCUP runs were done individually at MIT and INEEL, using the same model but with some differences in techniques and cross section libraries. Eigenvalue and isotope concentrations were compared on a PWR pin cell model up to high burnup. The eigenvalue comparison as a function of burnup is good: the maximum difference is within 2% and the average absolute difference less than 1%. The isotope concentration comparisons are better than a set of MOX fuel benchmarks and comparable to a set of uranium fuel benchmarks reported in the literature. The actinide and fission product data sources used in the MOCUP burnup calculations for a typical thorium fuel are documented. Reasons for code vs code differences are analyzed and discussed.

  1. High Cycle Thermal Fatigue in French PWR

    SciTech Connect

    Blondet, Eric; Faidy, Claude

    2002-07-01

    Different fatigue-related incidents which occurred in the world on the auxiliary lines of the reactor coolant system (SIS, RHR, CVC) have led EDF to search solutions in order to avoid or to limit consequences of thermodynamic phenomenal (Farley-Tihange, free convection loop and stratification, independent thermal cycling). Studies are performed on mock-up and compared with instrumentation on nuclear power stations. At the present time, studies allow EDF to carry out pipe modifications and to prepare specifications and recommendations for next generation of nuclear power plants. In 1998, a new phenomenal appeared on RHR system in Civaux. A crack was discovered in an area where hot and cold fluids (temperature difference of 140 deg. C) were mixed. Metallurgic studies concluded that this crack was caused by high cycle thermal fatigue. Since 1998, EDF is making an inventory of all mixing areas in French PWR on basis of criteria. For all identified areas, a method was developed to improve the first classifying and to keep back only potential damage pipes. Presently, studies are performing on the charging line nozzle connected to the reactor pressure vessel. In order to evaluate the load history, a mock-up has been developed and mechanical calculations are realised on this nozzle. The paper will make an overview of EDF conclusions on these different points: - dead legs and vortex in a no flow connected line; - stratification; - mixing tees with high {delta}T. (authors)

  2. PwrSoC (integration of micro-magnetic inductors/transformers with active semiconductors) for more than Moore technologies

    NASA Astrophysics Data System (ADS)

    Mathuna, Cian Ó.; Wang, Ningning; Kulkarni, Santosh; Roy, Saibal

    2013-07-01

    This paper introduces the concept of power supply on chip (PwrSoC) which will enable the development of next-generation, functionally integrated, power management platforms with applications in dc-dc conversion, gate drives, isolated power transmission and ultimately, high granularity, on-chip, power management for mixed-signal, SOC chips. PwrSoC will integrate power passives with the power management IC, in a 3D stacked or monolithic form factor, thereby delivering the performance of a highefficiency dc-dc converter within the footprint of a low-efficiency linear regulator. A central element of the PwrSoC concept is the fabrication of power micro-magnetics on silicon to deliver micro-inductors and micro-transformers. The paper details the magnetics on silicon process which combines thin film magnetic core technology with electroplated copper conductors. Measured data for micro-inductors show inductance operation up to 20 MHz, footprints down to 0.5 mm2, efficiencies up to 93% and dc current carrying capability up to 600 mA. Measurements on micro-transformers show voltage gain of approximately - 1 dB at between 10 MHz and 30 MHz. Contribution to the Topical Issue “International Semiconductor Conference Dresden-Grenoble - ISCDG 2012”, Edited by Gérard Ghibaudo, Francis Balestra and Simon Deleonibus.

  3. Evaluation of stress corrosion cracking of irradiated 304L stainless steel in PWR environment using heavy ion irradiation

    NASA Astrophysics Data System (ADS)

    Gupta, J.; Hure, J.; Tanguy, B.; Laffont, L.; Lafont, M.-C.; Andrieu, E.

    2016-08-01

    IASCC has been a major concern regarding the structural and functional integrity of core internals of PWR's, especially baffle-to-former bolts. Despite numerous studies over the past few decades, additional evaluation of the parameters influencing IASCC is still needed for an accurate understanding and modeling of this phenomenon. In this study, Fe irradiation at 450 °C was used to study the cracking susceptibility of 304 L austenitic stainless steel. After 10 MeV Fe irradiation to 5 dpa, irradiation-induced damage in the microstructure was characterized and quantified along with nano-hardness measurements. After 4% plastic strain in a PWR environment, quantitative information on the degree of strain localization, as determined by slip-line spacing, was obtained using SEM. Fe-irradiated material strained to 4% in a PWR environment exhibited crack initiation sites that were similar to those that occur in neutron- and proton-irradiated materials, which suggests that Fe irradiation may be a representative means for studying IASCC susceptibility. Fe-irradiated material subjected to 4% plastic strain in an inert argon environment did not exhibit any cracking, which suggests that localized deformation is not in itself sufficient for initiating cracking for the irradiation conditions used in this study.

  4. Validation of the new code package APOLLO2.8 for accurate PWR neutronics calculations

    SciTech Connect

    Santamarina, A.; Bernard, D.; Blaise, P.; Leconte, P.; Palau, J. M.; Roque, B.; Vaglio, C.; Vidal, J. F.

    2013-07-01

    This paper summarizes the Qualification work performed to demonstrate the accuracy of the new APOLLO2.S/SHEM-MOC package based on JEFF3.1.1 nuclear data file for the prediction of PWR neutronics parameters. This experimental validation is based on PWR mock-up critical experiments performed in the EOLE/MINERVE zero-power reactors and on P.I. Es on spent fuel assemblies from the French PWRs. The Calculation-Experiment comparison for the main design parameters is presented: reactivity of UOX and MOX lattices, depletion calculation and fuel inventory, reactivity loss with burnup, pin-by-pin power maps, Doppler coefficient, Moderator Temperature Coefficient, Void coefficient, UO{sub 2}-Gd{sub 2}O{sub 3} poisoning worth, Efficiency of Ag-In-Cd and B4C control rods, Reflector Saving for both standard 2-cm baffle and GEN3 advanced thick SS reflector. From this qualification process, calculation biases and associated uncertainties are derived. This code package APOLLO2.8 is already implemented in the ARCADIA new AREVA calculation chain for core physics and is currently under implementation in the future neutronics package of the French utility Electricite de France. (authors)

  5. Leak before break application in French PWR plants under operation

    SciTech Connect

    Faidy, C.

    1997-04-01

    Practical applications of the leak-before break concept are presently limited in French Pressurized Water Reactors (PWR) compared to Fast Breeder Reactors. Neithertheless, different fracture mechanic demonstrations have been done on different primary, auxiliary and secondary PWR piping systems based on similar requirements that the American NUREG 1061 specifications. The consequences of the success in different demonstrations are still in discussion to be included in the global safety assessment of the plants, such as the consequences on in-service inspections, leak detection systems, support optimization,.... A large research and development program, realized in different co-operative agreements, completes the general approach.

  6. PWR fuel features to preclude externally induced damage

    SciTech Connect

    Shallenberger, J.M.; Wilson, J.F.; Knott, R.P.

    1987-01-01

    Over the past several years there have been instances of pressurized water reactor (PWR) fuel damage attributed to factors external to the fuel. These externally induced causes include debris in the reactor coolant and baffle jetting. These causes of PWR fuel damage account for --50% of the total number of damaged rods. This paper discusses two features that significantly reduce the potential for fuel damage due to debris and baffle jetting. These two features are the debris filter bottom nozzle (DFBN) and the antivibration clip.

  7. Risk analysis of highly combustible gas storage, supply, and distribution systems in PWR plants

    SciTech Connect

    Simion, G.P.; VanHorn, R.L.; Smith, C.L.; Bickel, J.H.; Sattison, M.B.; Bulmahn, K.D.

    1993-06-01

    This report presents the evaluation of the potential safety concerns for pressurized water reactors (PWRs) identified in Generic Safety Issue 106, Piping and the Use of Highly Combustible Gases in Vital Areas. A Westinghouse four-loop PWR plant was analyzed for the risk due to the use of combustible gases (predominantly hydrogen) within the plant. The analysis evaluated an actual hydrogen distribution configuration and conducted several sensitivity studies to determine the potential variability among PWRs. The sensitivity studies were based on hydrogen and safety-related equipment configurations observed at other PWRs within the United States. Several options for improving the hydrogen distribution system design were identified and evaluated for their effect on risk and core damage frequency. A cost/benefit analysis was performed to determine whether alternatives considered were justifiable based on the safety improvement and economics of each possible improvement.

  8. Quantitative uncertainty and sensitivity analysis of a PWR control rod ejection accident

    SciTech Connect

    Pasichnyk, I.; Perin, Y.; Velkov, K.

    2013-07-01

    The paper describes the results of the quantitative Uncertainty and Sensitivity (U/S) Analysis of a Rod Ejection Accident (REA) which is simulated by the coupled system code ATHLET-QUABOX/CUBBOX applying the GRS tool for U/S analysis SUSA/XSUSA. For the present study, a UOX/MOX mixed core loading based on a generic PWR is modeled. A control rod ejection is calculated for two reactor states: Hot Zero Power (HZP) and 30% of nominal power. The worst cases for the rod ejection are determined by steady-state neutronic simulations taking into account the maximum reactivity insertion in the system and the power peaking factor. For the U/S analysis 378 uncertain parameters are identified and quantified (thermal-hydraulic initial and boundary conditions, input parameters and variations of the two-group cross sections). Results for uncertainty and sensitivity analysis are presented for safety important global and local parameters. (authors)

  9. Results from semiscale MOD-2A upper head injection test series. [PWR

    SciTech Connect

    Shimeck, D.J.; Leonard, M.T.

    1981-01-01

    A series of small break loss-of-coolant (SBLOCA) experiments and associated RELAP5/MOD computer code calculations have been performed by the Semiscale Program at the Idaho National Engineering Laboratory (INEL) to investigate the influence of upper head injection (UHI) on transient response. A UHI system, as designed for pressurized water reactors (PWR's), has an 8.7-MPa accumulator that injects emergency core coolant (ECC) directly into the upper head of the reactor vessel, and loop accumulators nominally pressurized to 2.86 MPa (as opposed to 4.14 MPa in a standard design). Since this configuration was optimized based upon large break LOCA calculations the experiments were requested by the US Nuclear Regulatory Commission (USNRC) to assist in evaluating system performance for SBLOCA's.

  10. Effect of coolant chemistry on PWR radiation transport processes. Progress report on reactor loop studies

    SciTech Connect

    Brown, D.J.; Flynn, G.; Haynes, J.W.; Kitt, G.P.; Large, N.R.; Lawson, D.; Mead, A.P.; Nichols, J.L.; Woodwark, D.R.

    1986-05-01

    The effect of various PWR-type coolant chemistry regimes on the behavior of corrosion products has been studied in the DIDO Water Loop at Harwell. There are strong indications that the in-core deposition behavior of corrosion product species is not fully accounted for by the solubility model based on nickel ferrite; boric acid plays a role apart from its influence on pH, and corrosion products are adsorbed to some extent in the zirconium oxide film on the fuel cladding. In DWL, soluble species appear to be dominant in deposition processes. A most important factor governing deposition behavior is surface condition; the influence of weld regions and the effect of varying pretreatment conditions have both been demonstrated. 13 figs.

  11. Source term experiment STEP-3 simulating a PWR severe station blackout

    SciTech Connect

    Simms, R.; Baker, L. Jr.; Ritzman, R.L.

    1987-05-21

    For a severe PWR accident that leads to a loss of feedwater to the steam generators, such as might occur in a station blackout, fission product decay heating will cause a water boiloff. Without effective cooling of the core, steam will begin to oxidize the Zircaloy cladding. The noble gases and volatile fission products, such as Cs and I, that are major contributors to the radiological source term, will be released from the damaged fuel shortly after cladding failure. The accident environment when these volatile fission products escape was simulated in STEP-3 using four fuel elements from the Belgonucleaire BR3 reactor. The primary objective was to examine the releases in samples collected as close to the test zone as possible. In this paper, an analysis of the temperatures and hydrogen generation is compared with the measurements. The analysis is needed to estimate releases and characterize conditions at the source for studies of fission product transport.

  12. Tritium removal and retention device. [PWR; BWR

    SciTech Connect

    Boyle, R.F.; Durigon, D.D.

    1981-07-21

    Apparatus comprising a two layered composite with an internal core of zirconium or zirconium alloy which retains tritium, and an adherent nickel outer layer which acts as a protective and selective window for passage of the tritium.

  13. Robotic inspection of PWR coolant pump casing welds

    SciTech Connect

    Pratt, W.R.; Alford, J.W.; Davis, J.B.

    1997-12-01

    As of January 1, 1995, the Swedish Nuclear Inspectorate began requiring more thorough inspections of cast stainless-steel components in nuclear power plants, including pressurized water reactor (PWR) reactor coolant pump (RCP) casings. The examination requirements are established by fracture mechanics analyses of component weldments and demonstrated test system detection capabilities. This may include full volumetric inspection or some portion thereof. Ringhals station is a four-unit nuclear power plant, owned and operated by the Swedish State Power Board, Vattenfall. Unit 1 is a boiling water reactor. Units 2, 3, and 4 are Westinghouse-designed PWRs, ranging in size from 795 to 925 MW. The RCP casings at the PWR units are made of cast stainless steel and contain four circumferential welds that require inspection. Due to the thickness of the casings at the weld locations and configuration and surface conditions on the outside diameter of the casings, remote inspection from the inside diameter of the pump casing was mandated.

  14. Report on the PWR-radiation protection/ALARA Committee

    SciTech Connect

    Malone, D.J.

    1995-03-01

    In 1992, representatives from several utilities with operational Pressurized Water Reactors (PWR) formed the PWR-Radiation Protection/ALARA Committee. The mission of the Committee is to facilitate open communications between member utilities relative to radiation protection and ALARA issues such that cost effective dose reduction and radiation protection measures may be instituted. While industry deregulation appears inevitable and inter-utility competition is on the rise, Committee members are fully committed to sharing both positive and negative experiences for the benefit of the health and safety of the radiation worker. Committee meetings provide current operational experiences through members providing Plant status reports, and information relative to programmatic improvements through member presentations and topic specific workshops. The most recent Committee workshop was facilitated to provide members with defined experiences that provide cost effective ALARA performance.

  15. Update on the PWR axial burnup profile database

    SciTech Connect

    Cacciapouti, R.F.; Volkinburg, S.V.

    1995-12-01

    A pressurized water reactor database was developed to evaluate the axial burnup profiles of various reactor types. The data showed that the various types exhibit similar behavior, especially at the top and bottom of the assembly. From the existing data, bounding axial burnup profiles can be developed to envelope the various pressurized water reactor assembly deigns. The database encompasses most of the PWR fuel designs and contains sufficient data to provide reliable statistics.

  16. Neutron-gamma flux and dose calculations in a Pressurized Water Reactor (PWR)

    NASA Astrophysics Data System (ADS)

    Brovchenko, Mariya; Dechenaux, Benjamin; Burn, Kenneth W.; Console Camprini, Patrizio; Duhamel, Isabelle; Peron, Arthur

    2017-09-01

    The present work deals with Monte Carlo simulations, aiming to determine the neutron and gamma responses outside the vessel and in the basemat of a Pressurized Water Reactor (PWR). The model is based on the Tihange-I Belgian nuclear reactor. With a large set of information and measurements available, this reactor has the advantage to be easily modelled and allows validation based on the experimental measurements. Power distribution calculations were therefore performed with the MCNP code at IRSN and compared to the available in-core measurements. Results showed a good agreement between calculated and measured values over the whole core. In this paper, the methods and hypotheses used for the particle transport simulation from the fission distribution in the core to the detectors outside the vessel of the reactor are also summarized. The results of the simulations are presented including the neutron and gamma doses and flux energy spectra. MCNP6 computational results comparing JEFF3.1 and ENDF-B/VII.1 nuclear data evaluations and sensitivity of the results to some model parameters are presented.

  17. Evaluation of zinc addition to PWR primary coolant

    SciTech Connect

    Pathania, R.; Yagnik, S.; Gold, R.E.; Dove, M.; Kolstad, E.

    1995-12-31

    Laboratory studies have shown that addition of zinc to a PWR environment reduces the general corrosion rates of materials in the primary system and delays the initiation of primary water stress corrosion cracking (PWSCC) in Alloy 600. Because of the potential benefits of zinc addition in reducing radiation fields and mitigating PWSCC of Alloy 600 a project was initiated to qualify zinc addition to a PWR. The objective of this work was to evaluate the effect of zinc addition on radiation fields, PWSCC of Alloy 600 and fuel cladding corrosion at the Farley-2 PWR. In order to provide an early warning of any potential adverse effects on the fuel cladding, corrosion studies were initiated at the Halden test reactor prior to zinc addition at Farley-2. This paper provides an overview of the scope of the zinc addition demonstration at Farley-2 and the fuel cladding corrosion tests at Halden. The zinc concentration in the Farley-2 coolant is approximately 40 ppb and that in Halden is 50 ppb. The paper presents initial results from these studies which are still in progress.

  18. PWR Cross Section Libraries for ORIGEN-ARP

    SciTech Connect

    McGraw, Carolyn; Ilas, Germina

    2012-01-01

    New pressurized water reactor (PWR) cross-section libraries were generated for use with the ORIGEN-ARP depletion sequence in the SCALE nuclear analysis code system. These libraries are based on ENDF/B-VII nuclear data and were generated using the two-dimensional depletion sequence, TRITON/NEWT, in SCALE 6.1. The libraries contain multiple burnup-dependent cross-sections for seven PWR fuel designs, with enrichments ranging from 1.5 to 6 wt% 235U. The burnup range has been extended from the 72 GWd/MTU used in previous versions of the libraries to 90 GWd/MTU. Validation of the libraries using radiochemical assay measurements and decay heat measurements for PWR spent fuel showed good agreement between calculated and experimental data. Verification against detailed TRITON simulations for the considered assembly designs showed that depletion calculations performed in ORIGEN-ARP with the pre-generated libraries provide similar results as obtained with direct TRITON depletion, while greatly reducing the computation time.

  19. Effect of aging on the PWR Chemical and Volume Control System

    SciTech Connect

    Grove, E.J.; Travis, R.J.; Aggarwal, S.K.

    1995-06-01

    The PWR Chemical and Volume Control System (CVCS) is designed to provide both safety and non-safety related functions. During normal plant operation it is used to control reactor coolant chemistry, and letdown and charging flow. In many plants, the charging pumps also provide high pressure injection, emergency boration, and RCP seal injection in emergency situations. This study examines the design, materials, maintenance, operation and actual degradation experiences of the system and main sub-components to assess the potential for age degradation. A detailed review of the Nuclear Plant Reliability Data System (NPRDS) and Licensee Event Report (LER) databases for the 1988--1991 time period, together with a review of industry and NRC experience and research, indicate that age-related degradations and failures have occurred. These failures had significant effects on plant operation, including reactivity excursions, and pressurizer level transients. The majority of these component failures resulted in leakage of reactor coolant outside the containment. A representative plant of each PWR design (W, CE, and B and W) was visited to obtain specific information on system inspection, surveillance, monitoring, and inspection practices. The results of these visits indicate that adequate system maintenance and inspection is being performed. In some instances, the frequencies of inspection were increase in response to repeated failure events. A parametric study was performed to assess the effect of system aging on Core Damage Frequency (CDF). This study showed that as motor-operated valve (MOV) operating failures increased, the contribution of the High Pressure Injection to CDF also increased.

  20. Analyses of High Pressure Molten Debris Dispersion for a Typical PWR Plant

    SciTech Connect

    Osamu KAawabata; Mitsuhiro Kajimoto

    2006-07-01

    In such severe core damage accident, as small LOCAs with no ECCS injection or station blackout, in which the primary reactor system remains pressurized during core melt down, certain modes of vessel failure would lead to a high pressure ejection of molten core material. In case of a local failure of the lower head, the molten materials would initially be ejected into the cavity beneath the pressure vessel may subsequently be swept out from the cavity to the containment atmosphere and it might cause the early containment failure by direct contact of containment steel liner with core debris. When the contribution of a high-pressure scenario in a core damage frequency increases, early conditional containment failure probability may become large. In the present study, the verification analysis of PHOENICS code and the combining analysis with MELCOR and PHOENICS codes were performed to examine the debris dispersion behavior during high pressure melt ejection. The PHOENICS code which can treat thermal hydraulic phenomena, was applied to the verification analysis for melt dispersion experiments conducted by the Purdue university in the United States. A low pressure melt dispersion experiment at initial pressure 1.4 MPas used metal woods as a molten material was simulated. The analytical results with molten debris dispersion mostly from the model reactor cavity compartment showed an agreement with the experimental result, but the analysis result of a volumetric median diameter of the airborne debris droplets was estimated about 1.5 times of the experimental result. The injection rates of molten debris and steam after reactor vessel failure for a typical PWR plant were analyzed using the MELCOR code. In addition, PHOENICS was applied to a 3D analysis for debris dispersion with low primary pressure at the reactor vessel failure. The analysis result showed that almost all the molten debris were dispersed from the reactor vessel cavity compartment by about 45 seconds after the

  1. Development and Application of Laser Peening System for PWR Power Plants

    SciTech Connect

    Masaki Yoda; Itaru Chida; Satoshi Okada; Makoto Ochiai; Yuji Sano; Naruhiko Mukai; Gaku Komotori; Ryoichi Saeki; Toshimitsu Takagi; Masanori Sugihara; Hirokata Yoriki

    2006-07-01

    Laser peening is a process to improve residual stress from tensile to compressive in surface layer of materials by irradiating high-power laser pulses on the material in water. Toshiba has developed a laser peening system composed of Q-switched Nd:YAG laser oscillators, laser delivery equipment and underwater remote handling equipment. We have applied the system for Japanese operating BWR power plants as a preventive maintenance measure for stress corrosion cracking (SCC) on reactor internals like core shrouds or control rod drive (CRD) penetrations since 1999. As for PWRs, alloy 600 or 182 can be susceptible to primary water stress corrosion cracking (PWSCC), and some cracks or leakages caused by the PWSCC have been discovered on penetrations of reactor vessel heads (RVHs), reactor bottom-mounted instrumentation (BMI) nozzles, and others. Taking measures to meet the unconformity of the RVH penetrations, RVHs themselves have been replaced in many PWRs. On the other hand, it's too time-consuming and expensive to replace BMI nozzles, therefore, any other convenient and less expensive measures are required instead of the replacement. In Toshiba, we carried out various tests for laser-peened nickel base alloys and confirmed the effectiveness of laser peening as a preventive maintenance measure for PWSCC. We have developed a laser peening system for PWRs as well after the one for BWRs, and applied it for BMI nozzles, core deluge line nozzles and primary water inlet nozzles of Ikata Unit 1 and 2 of Shikoku Electric Power Company since 2004, which are Japanese operating PWR power plants. In this system, laser oscillators and control devices were packed into two containers placed on the operating floor inside the reactor containment vessel. Laser pulses were delivered through twin optical fibers and irradiated on two portions in parallel to reduce operation time. For BMI nozzles, we developed a tiny irradiation head for small tubes and we peened the inner surface around J

  2. Phenomenological modelling of steam explosions. [PWR; BWR

    SciTech Connect

    Corradini, M.L.; Drumheller, D.S.

    1980-01-01

    During a hypothetical core meltdown accident, an important safety issue to be addressed is the potential for steam explosions. This paper presents analysis and modelling of experimental results. There are four observations that can be drawn from the analysis: (1) vapor explosions are suppressed by noncondensible gases generated by fuel oxidation, by high ambient pressure, and by high water temperatures; (2) these effects appear to be trigger-related in that an explosion can again be induced in some cases by increasing the trigger magnitude; (3) direct fuel liquid-coolant liquid contact can explain small scale fuel fragmentation; (4) heat transfer during the expansion phase of the explosion can reduce the work potential.

  3. MELCOR 1.8.2 assessment: Surry PWR TMLB` (with a DCH study)

    SciTech Connect

    Kmetyk, L.N.; Cole, R.K. Jr.; Smith, R.C.; Summers, R.M.; Thompson, S.L.

    1994-02-01

    MELCOR is a fully integrated, engineering-level computer code, being developed at Sandia National Laboratories for the USNRC. This code models the entire spectrum of severe accident phenomena in a unified framework for both BWRs and PWRs. As part of an ongoing assessment program, the MELCOR computer code has been used to analyze a station blackout transient in Surry, a three-loop Westinghouse PWR. Basecase results obtained with MELCOR 1.8.2 are presented, and compared to earlier results for the same transient calculated using MELCOR 1.8.1. The effects of new models added in MELCOR 1.8.2 (in particular, hydrodynamic interfacial momentum exchange, core debris radial relocation and core material eutectics, CORSOR-Booth fission product release, high-pressure melt ejection and direct containment heating) are investigated individually in sensitivity studies. The progress in reducing numeric effects in MELCOR 1.8.2, compared to MELCOR 1.8.1, is evaluated in both machine-dependency and time-step studies; some remaining sources of numeric dependencies (valve cycling, material relocation and hydrogen burn) are identified.

  4. Core physics analysis of 100% MOX Core in IRIS

    SciTech Connect

    Franceschini, F.; Petrovic, B.

    2006-07-01

    International Reactor Innovative and Secure (IRIS) is an advanced small-to-medium-size (1000 MWt) Pressurized Water Reactor (PWR), targeting deployment around 2015. Its reference core design is based on the current Westinghouse UO{sub 2} fuel with less than 5% {sup 235}U, and the analysis has been previously completed confirming good performance. The full MOX fuel core is currently under evaluation as one of the alternatives for the second wave of IRIS reactors. A full 3-D neutronic analysis has been performed to examine main core performance parameters, such as critical boron concentration, peaking factors, discharge burnup, etc. The enhanced moderation of the IRIS fuel lattice facilitates MOX core design, and all the obtained results are within the requirements, confirming viability of this option from the reactor physics standpoint. (authors)

  5. Comparison of PWR-IMF and FR fuel cycles

    SciTech Connect

    Darilek, Petr; Zajac, Radoslav; Breza, Juraj |; Necas, Vladimir

    2007-07-01

    The paper gives a comparison of PWR (Russia origin VVER-440) cycle with improved micro-heterogeneous inert matrix fuel assemblies and FR cycle. Micro-heterogeneous combined assembly contains transmutation pins with Pu and MAs from burned uranium reprocessing and standard uranium pins. Cycle analyses were performed by HELIOS spectral code and SCALE code system. Comparison is based on fuel cycle indicators, used in the project RED-IMPACT - part of EU FP6. Advantages of both closed cycles are pointed out. (authors)

  6. Probabilistic fracture mechanics code for PWR steam generator tube maintenance

    SciTech Connect

    Granger, B. ); Pitner, P. ); Flesch, B. )

    1991-01-01

    This paper presents the COMPROMIS code developed by Electricite de France (EDF) to optimize the maintenance of PWR steam generator (SG) tube bundles. This model, based on probabilistic fracture mechanics, quantifies the impact of in-service inspections and maintenance actions on the risk of failure of an SG tube, with allowance as random variable for all the relevant parameters (distribution of crack sizes, detection and sizing capability, crack initiation and propagation, critical sizes, leak before break risk). The code is SG-specific and is designed to allow realtime evaluation based on manufacturing and inspection data banks.

  7. Timing analysis of PWR fuel pin failures

    SciTech Connect

    Jones, K.R.; Wade, N.L.; Katsma, K.R.; Siefken, L.J. ); Straka, M. )

    1992-09-01

    Research has been conducted to develop and demonstrate a methodology for calculation of the time interval between receipt of the containment isolation signals and the first fuel pin failure for loss-of-coolant accidents (LOCAs). Demonstration calculations were performed for a Babcock and Wilcox (B W) design (Oconee) and a Westinghouse (W) four-loop design (Seabrook). Sensitivity studies were performed to assess the impacts of fuel pin bumup, axial peaking factor, break size, emergency core cooling system availability, and main coolant pump trip on these times. The analysis was performed using the following codes: FRAPCON-2, for the calculation of steady-state fuel behavior; SCDAP/RELAP5/MOD3 and TRACPF1/MOD1, for the calculation of the transient thermal-hydraulic conditions in the reactor system; and FRAP-T6, for the calculation of transient fuel behavior. In addition to the calculation of fuel pin failure timing, this analysis provides a comparison of the predicted results of SCDAP/RELAP5/MOD3 and TRAC-PFL/MOD1 for large-break LOCA analysis. Using SCDAP/RELAP5/MOD3 thermal-hydraulic data, the shortest time intervals calculated between initiation of containment isolation and fuel pin failure are 10.4 seconds and 19.1 seconds for the B W and W plants, respectively. Using data generated by TRAC-PF1/MOD1, the shortest intervals are 10.3 seconds and 29.1 seconds for the B W and W plants, respectively. These intervals are for a double-ended, offset-shear, cold leg break, using the technical specification maximum peaking factor and applied to fuel with maximum design bumup. Using peaking factors commensurate widi actual bumups would result in longer intervals for both reactor designs. This document also contains appendices A through J of this report.

  8. Beta and gamma dose calculations for PWR and BWR containments

    SciTech Connect

    King, D.B.

    1989-07-01

    Analyses of gamma and beta dose in selected regions in PWR and BWR containment buildings have been performed for a range of fission product releases from selected severe accidents. The objective of this study was to determine the radiation dose that safety-related equipment could experience during the selected severe accident sequences. The resulting dose calculations demonstrate the extent to which design basis accident qualified equipment could also be qualified for the severe accident environments. Surry was chosen as the representative PWR plant while Peach Bottom was selected to represent BWRs. Battelle Columbus Laboratory performed the source term release analyses. The AB epsilon scenario (an intermediate to large LOCA with failure to recover onsite or offsite electrical power) was selected as the base case Surry accident, and the AE scenario (a large break LOCA with one initiating event and a combination of failures in two emergency cooling systems) was selected as the base case Peach Bottom accident. Radionuclide release was bounded for both scenarios by including spray operation and arrested sequences as variations of the base scenarios. Sandia National Laboratories used the source terms to calculate dose to selected containment regions. Scenarios with sprays operational resulted in a total dose comparable to that (2.20 /times/ 10/sup 8/ rads) used in current equipment qualification testing. The base case scenarios resulted in some calculated doses roughly an order of magnitude above the current 2.20 /times/ 10/sup 8/ rad equipment qualification test region. 8 refs., 23 figs., 12 tabs.

  9. A comprehensive in-pile test of PWR fuel bundle

    NASA Astrophysics Data System (ADS)

    Kang, Rixin; Zhang, Shucheng; Chen, Dianshan

    1991-02-01

    An in-pile test of PWR fuel bundle has been conducted in HWRR at IAE of China. This paper describes the structure of the test bundle (3 × 3-2), fabrication process and quality control of the fuel rod, irradiation conditions and the main Post Irradiation Examination (PIE) results. The test fuel bundle was irradiated under the PWR operation and water chemistry conditions with an average linear power of 381 W/cm and reached an average burnup of 25010 MWd/tU of the fuel bundle. After the test, destructive and non-destructive examination of the fuel rods was conducted at hot laboratories. The fission gas release was 10.4-23%. The ridge height of cladding was 3 to 8 μm. The hydrogen content of the cladding was 80 to 140 ppm. The fuel stack height was increased by 2.9 to 3.3 mm. The relative irradiation growth was about 0.11 to 0.17% of the fuel rod length. During the irradiation test, no fuel rod failure or other abnormal phenomena had been found by the on-line fuel failure monitoring system of the test loop and water sampling analysis. The structure of the test fuel assembly was left undamaged without twist and detectable deformation.

  10. Presentation of the MERC work-flow for the computation of a 2D radial reflector in a PWR

    SciTech Connect

    Clerc, T.; Hebert, A.; Leroyer, H.; Argaud, J. P.; Poncot, A.; Bouriquet, B.

    2013-07-01

    This paper presents a work-flow for computing an equivalent 2D radial reflector in a pressurized water reactor (PWR) core, in adequacy with a reference power distribution, computed with the method of characteristics (MOC) of the lattice code APOLLO2. The Multi-modelling Equivalent Reflector Computation (MERC) work-flow is a coherent association of the lattice code APOLLO2 and the core code COCAGNE, structured around the ADAO (Assimilation de Donnees et Aide a l'Optimisation) module of the SALOME platform, based on the data assimilation theory. This study leads to the computation of equivalent few-groups reflectors, that can be spatially heterogeneous, which have been compared to those obtained with the OPTEX similar methodology developed with the core code DONJON, as a first validation step. Subsequently, the MERC work-flow is used to compute the most accurate reflector in consistency with all the R and D choices made at Electricite de France (EDF) for the core modelling, in terms of number of energy groups and simplified transport solvers. We observe important reductions of the power discrepancies distribution over the core when using equivalent reflectors obtained with the MERC work-flow. (authors)

  11. Nuclear Data Library Effects on Fast to Thermal Flux Shapes Around PWR Control Rod Tips

    NASA Astrophysics Data System (ADS)

    Vasiliev, A.; Ferroukhi, H.; Zhu, T.; Pautz, A.

    2014-04-01

    The development of a high-fidelity computational scheme to estimate the accumulated fluence at the tips of PWR control rods (CR) has been initiated at the Paul Scherrer Institut (PSI). Both the fluence from high-energy (E>1 MeV) neutrons as well as for the thermal range (E<0.625 eV) are required as these affect the CR integrity through stresses/strains induced by coupled clad embrittlement / absorber swelling phenomena. The concept of the PSI scheme under development is to provide from validated core analysis models, the volumetric neutron source to a full core MCNPX model that is then used to compute the neutron fluxes. A particular aspect that needs scrutiny is the ability of the MCNPX-based calculation methodology to accurately predict the flux shapes along the control rod surfaces, especially for fully withdrawn CRs. In that case, the tip is located a short distance above the core/reflector interface and since this situation corresponds to a large part of reactor operation, the accumulated fluence will highly depend on the achieved calculation accuracy and precision in this non-fueled zone. The objective of the work presented in this paper is to quantify the influence of nuclear data on the calculated fluxes at the CR tips by (1) conducting a systematic comparison of modern neutron cross-section libraries, including JENDL-4.0, JEFF-3.1.1 and ENDF/B-VII.0, and (2) by quantifying the uncertainties in the neutron flux calculations with the help of available neutron cross-section variances/covariances data. For completeness, the magnitude of these nuclear data-based uncertainties is also assessed in relation to the influence from other typical sources of modeling uncertainties/biases.

  12. PWR FLECHT SEASET 163-Rod Bundle Flow Blockage Task data report. NRC/EPRI/Westinghouse report No. 13, August-October 1982

    SciTech Connect

    Loftus, M J; Hochreiter, L E; McGuire, M F; Valkovic, M M

    1983-10-01

    This report presents data from the 163-Rod Bundle Blow Blockage Task of the Full-Length Emergency Cooling Heat Transfer Systems Effects and Separate Effects Test Program (FLECHT SEASET). The task consisted of forced and gravity reflooding tests utilizing electrical heater rods with a cosine axial power profile to simulate PWR nuclear core fuel rod arrays. These tests were designed to determine effects of flow blockage and flow bypass on reflooding behavior and to aid in the assessment of computational models in predicting the reflooding behavior of flow blockage in rod bundle arrays.

  13. Integrated Radiation Transport and Thermo-Mechanics Simulation of a PWR Assembly

    SciTech Connect

    Clarno, Kevin T; Hamilton, Steven P; Philip, Bobby; Sampath, Rahul S; Allu, Srikanth; Berrill, Mark A; Barai, Pallab; Banfield, James E

    2012-01-01

    The Advanced Multi-Physics (AMP) Nuclear Fuel Performance code (AMPFuel) is focused on predicting the temperature and strain within a nuclear fuel assembly to evaluate the performance and safety of existing and advanced nuclear fuel bundles within existing and advanced nuclear reactors. AMPFuel was extended to include an integrated nuclear fuel assembly capability for (one-way) coupled radiation transport and nuclear fuel assembly thermo-mechanics. This capability is the initial step towards incorporating an improved predictive nuclear fuel assembly modeling capability to accurately account for source terms, such as the neutron flux distribution, coolant conditions, and assembly mechanical stresses, of traditional (single-pin) nuclear fuel performance simulation. AMPFuel was used to model an entire 17 x 17 Pressurized Water Reactor (PWR) fuel assembly with many of the features resolved in three dimensions (for thermo-mechanics and/or neutronics), including the fuel, gap, and cladding of each of the 264 fuel pins, the 25 guide tubes, top and bottom structural regions, and the upper and lower (neutron) reflector regions. The final full-assembly calculation was executed on Jaguar (Cray XT5) at the Oak Ridge Leadership Computing Facility using 40,000 cores in under 10 hours to model over 162 billion degrees of freedom for 10 loading steps.

  14. TREAT source-term experiment STEP-1 simulating a PWR LOCA

    SciTech Connect

    Simms, R.; Baker, L. Jr.; Blomquist, C.A.; Ritzman, R.L.

    1986-01-01

    In a hypothetical pressurized water reactor (PWR) large-break loss-of-coolant accident (LOCA) in which the emergency core cooling system fails, fission product decay heating causes water boil-off and reduced heat removal. Zircaloy cladding is oxidized by the steam. The noble gases and volatile fission products such as cesium and iodine that constitute a principal part of the source term will be released from the damaged fuel at or shortly after the time of cladding failure. TREAT test STEP-1 simulated the LOCA environment when the volatile fission products would be released using four fuel elements from the Belgonucleaire BR3 reactor. The principal objective was to collect a portion of the releases carried by the flow stream in a region as close as possible to the test zone. In this paper, the test is described and the results of an analysis of the thermal and steam/hydrogen environment are compared with the test measurements in order to provide a characterization for analysis of fission product releases and aerosol formation. The results of extensive sample examinations are reported separately.

  15. A comparison of fuzzy logic-PID control strategies for PWR pressurizer control

    SciTech Connect

    Kavaklioglu, K.; Ikonomopoulos, A. )

    1993-01-01

    This paper describes the results obtained from a comparison performed between classical proportional-integral-derivative (PID) and fuzzy logic (FL) controlling the pressure in a pressurized water reactor (PWR). The two methodologies have been tested under various transient scenarios, and their performances are evaluated with respect to robustness and on-time response to external stimuli. One of the main concerns in the safe operation of PWR is the pressure control in the primary side of the system. In order to maintain the pressure in a PWR at the desired level, the pressurizer component equipped with sprayers, heaters, and safety relief valves is used. The control strategy in a Westinghouse PWR is implemented with a PID controller that initiates either the electric heaters or the sprayers, depending on the direction of the coolant pressure deviation from the setpoint.

  16. Modeling local chemistry in PWR steam generator crevices

    SciTech Connect

    Millett, P.J.

    1997-02-01

    Over the past two decades steam generator corrosion damage has been a major cost impact to PWR owners. Crevices and occluded regions create thermal-hydraulic conditions where aggressive impurities can become highly concentrated, promoting localized corrosion of the tubing and support structure materials. The type of corrosion varies depending on the local conditions, with stress corrosion cracking being the phenomenon of most current concern. A major goal of the EPRI research in this area has been to develop models of the concentration process and resulting crevice chemistry conditions. These models may then be used to predict crevice chemistry based on knowledge of bulk chemistry, thereby allowing the operator to control corrosion damage. Rigorous deterministic models have not yet been developed; however, empirical approaches have shown promise and are reflected in current versions of the industry-developed secondary water chemistry guidelines.

  17. Tritium target performance during an LBLOCA in a PWR

    SciTech Connect

    Reid, B.D.

    1996-12-31

    In December 1995, the U.S. Department of Energy (DOE) announced a preferred strategy for acquiring a new supply of tritium. That strategy is based on pursuing the two most promising production alternatives. These alternatives include either constructing an accelerator-produced tritium system for tritium production or procuring an existing commercial light water reactor or irradiation services from such a reactor to irradiate tritium targets. This paper discusses the safety performance of a tritium target in a commercial pressurized water reactor (PWR). The current conceptual design for the light water tritium targets is quite similar, in terms of external dimensions and materials, to early designs for stainless steel clad discrete burnable absorbers used in PWRs. The tritium targets nominally consist of an annular lithium aluminate pellet wrapped in a Zircaloy-4 getter and clad with Type 316 stainless steel.

  18. Fracture mechanics evaluation for at typical PWR primary coolant pipe

    SciTech Connect

    Tanaka, T.; Shimizu, S.; Ogata, Y.

    1997-04-01

    For the primary coolant piping of PWRs in Japan, cast duplex stainless steel which is excellent in terms of strength, corrosion resistance, and weldability has conventionally been used. The cast duplex stainless steel contains the ferrite phase in the austenite matrix and thermal aging after long term service is known to change its material characteristics. It is considered appropriate to apply the methodology of elastic plastic fracture mechanics for an evaluation of the integrity of the primary coolant piping after thermal aging. Therefore we evaluated the integrity of the primary coolant piping for an initial PWR plant in Japan by means of elastic plastic fracture mechanics. The evaluation results show that the crack will not grow into an unstable fracture and the integrity of the piping will be secured, even when such through wall crack length is assumed to equal the fatigue crack growth length for a service period of up to 60 years.

  19. Pump and valve fastener serviceability in PWR nuclear facilities

    SciTech Connect

    Moisidis, N.T.; Ratiu, M.D.

    1996-02-01

    The results of several studies conducted on corrosion of carbon and low-alloy steels in borated water have shown that impingement of borated steam on ferritic steels or contact with a moist paste of boric acid can lead to high corrosion rates due to high local concentrations of boric acid on the surface. The corrosion process of the flange fasteners of pumps and valves is considered a material compatibility and equipment maintenance problem. Therefore, the nuclear utilities of pressurized water reactor (PWR) power plants can prevent this damage by implementing appropriate fastener steel replacement and extended inspections to detect and correct the cause of leakage. A 3-phase corrosion protection program is presented for implementation based on system operability, outage-related accessibility, and cost of fastener replacement versus maintenance frequency increase. A selection criterion for fastener material is indicated based on service limitation: preloading and metal temperature.

  20. PWR and BWR spent fuel assembly gamma spectra measurements

    DOE PAGES

    Vaccaro, S.; Tobin, Stephen J.; Favalli, Andrea; ...

    2016-07-17

    A project to research the application of nondestructive assay (NDA) to spent fuel assemblies is underway. The research team comprises the European Atomic Energy Community (EURATOM), embodied by the European Commission, DG Energy, Directorate EURATOM Safeguards; the Swedish Nuclear Fuel and Waste Management Company (SKB); two universities; and several United States national laboratories. The Next Generation of Safeguards Initiative–Spent Fuel project team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detectmore » the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. This study focuses on spectrally resolved gamma-ray measurements performed on a diverse set of 50 assemblies [25 pressurized water reactor (PWR) assemblies and 25 boiling water reactor (BWR) assemblies]; these same 50 assemblies will be measured with neutron-based NDA instruments and a full-length calorimeter. Given that encapsulation/repository and dry storage safeguards are the primarily intended applications, the analysis focused on the dominant gamma-ray lines of 137Cs, 154Eu, and 134Cs because these isotopes will be the primary gamma-ray emitters during the time frames of interest to these applications. This study addresses the impact on the measured passive gamma-ray signals due to the following factors: burnup, initial enrichment, cooling time, assembly type (eight different PWR and six different BWR fuel designs), presence of gadolinium rods, and anomalies in operating history. As a result, to compare the measured results with theory, a limited number of ORIGEN-ARP simulations were performed.« less

  1. PWR and BWR spent fuel assembly gamma spectra measurements

    SciTech Connect

    Vaccaro, S.; Tobin, Stephen J.; Favalli, Andrea; Grogan, Brandon R.; Jansson, Peter; Liljenfeldt, Henrik; Mozin, Vladimir; Hu, Jianwei; Schwalbach, P.; Sjoland, A.; Trellue, Holly; Vo, D.

    2016-07-17

    A project to research the application of nondestructive assay (NDA) to spent fuel assemblies is underway. The research team comprises the European Atomic Energy Community (EURATOM), embodied by the European Commission, DG Energy, Directorate EURATOM Safeguards; the Swedish Nuclear Fuel and Waste Management Company (SKB); two universities; and several United States national laboratories. The Next Generation of Safeguards Initiative–Spent Fuel project team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detect the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. This study focuses on spectrally resolved gamma-ray measurements performed on a diverse set of 50 assemblies [25 pressurized water reactor (PWR) assemblies and 25 boiling water reactor (BWR) assemblies]; these same 50 assemblies will be measured with neutron-based NDA instruments and a full-length calorimeter. Given that encapsulation/repository and dry storage safeguards are the primarily intended applications, the analysis focused on the dominant gamma-ray lines of 137Cs, 154Eu, and 134Cs because these isotopes will be the primary gamma-ray emitters during the time frames of interest to these applications. This study addresses the impact on the measured passive gamma-ray signals due to the following factors: burnup, initial enrichment, cooling time, assembly type (eight different PWR and six different BWR fuel designs), presence of gadolinium rods, and anomalies in operating history. As a result, to compare the measured results with theory, a limited number of ORIGEN-ARP simulations were performed.

  2. PWR and BWR spent fuel assembly gamma spectra measurements

    SciTech Connect

    Vaccaro, S.; Tobin, Stephen J.; Favalli, Andrea; Grogan, Brandon R.; Jansson, Peter; Liljenfeldt, Henrik; Mozin, Vladimir; Hu, Jianwei; Schwalbach, P.; Sjoland, A.; Trellue, Holly; Vo, D.

    2016-07-17

    A project to research the application of nondestructive assay (NDA) to spent fuel assemblies is underway. The research team comprises the European Atomic Energy Community (EURATOM), embodied by the European Commission, DG Energy, Directorate EURATOM Safeguards; the Swedish Nuclear Fuel and Waste Management Company (SKB); two universities; and several United States national laboratories. The Next Generation of Safeguards Initiative–Spent Fuel project team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detect the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. This study focuses on spectrally resolved gamma-ray measurements performed on a diverse set of 50 assemblies [25 pressurized water reactor (PWR) assemblies and 25 boiling water reactor (BWR) assemblies]; these same 50 assemblies will be measured with neutron-based NDA instruments and a full-length calorimeter. Given that encapsulation/repository and dry storage safeguards are the primarily intended applications, the analysis focused on the dominant gamma-ray lines of 137Cs, 154Eu, and 134Cs because these isotopes will be the primary gamma-ray emitters during the time frames of interest to these applications. This study addresses the impact on the measured passive gamma-ray signals due to the following factors: burnup, initial enrichment, cooling time, assembly type (eight different PWR and six different BWR fuel designs), presence of gadolinium rods, and anomalies in operating history. As a result, to compare the measured results with theory, a limited number of ORIGEN-ARP simulations were performed.

  3. PWR and BWR spent fuel assembly gamma spectra measurements

    NASA Astrophysics Data System (ADS)

    Vaccaro, S.; Tobin, S. J.; Favalli, A.; Grogan, B.; Jansson, P.; Liljenfeldt, H.; Mozin, V.; Hu, J.; Schwalbach, P.; Sjöland, A.; Trellue, H.; Vo, D.

    2016-10-01

    A project to research the application of nondestructive assay (NDA) to spent fuel assemblies is underway. The research team comprises the European Atomic Energy Community (EURATOM), embodied by the European Commission, DG Energy, Directorate EURATOM Safeguards; the Swedish Nuclear Fuel and Waste Management Company (SKB); two universities; and several United States national laboratories. The Next Generation of Safeguards Initiative-Spent Fuel project team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detect the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. This study focuses on spectrally resolved gamma-ray measurements performed on a diverse set of 50 assemblies [25 pressurized water reactor (PWR) assemblies and 25 boiling water reactor (BWR) assemblies]; these same 50 assemblies will be measured with neutron-based NDA instruments and a full-length calorimeter. Given that encapsulation/repository and dry storage safeguards are the primarily intended applications, the analysis focused on the dominant gamma-ray lines of 137Cs, 154Eu, and 134Cs because these isotopes will be the primary gamma-ray emitters during the time frames of interest to these applications. This study addresses the impact on the measured passive gamma-ray signals due to the following factors: burnup, initial enrichment, cooling time, assembly type (eight different PWR and six different BWR fuel designs), presence of gadolinium rods, and anomalies in operating history. To compare the measured results with theory, a limited number of ORIGEN-ARP simulations were performed.

  4. Improvement of the thermal margins in the Swedish Ringhals-3 PWR by introducing new fuel assemblies with thorium

    SciTech Connect

    Lau, C. W.; Demaziere, C.; Nylen, H.; Sandberg, U.

    2012-07-01

    Thorium is a fertile material and most of the past research has focused on breeding thorium to fissile material. In this paper, the focus is on using thorium to improve the thermal margins by homogeneously distributing thorium in the fuel pellets. A proposed uranium-thorium-based fuel assembly is simulated for the Swedish Ringhals-3 PWR core in a realistic demonstration. All the key safety parameters, such as isothermal temperature coefficient of reactivity, Doppler temperature of reactivity, boron worth, shutdown margins and fraction of delayed neutrons are studied in this paper, and are within safety limits for the new core design using the uranium-thorium-based fuel assemblies. The calculations were performed by the two-dimensional transport code CASMO-4E and the two group steady-state three dimensional nodal code SIMULATE-3 from Studsvik Scandpower. The results showed that the uranium-thorium-based fuel assembly improves the thermal margins, both in the pin peak power and the local power (Fq). The improved thermal margins would allow more flexible core designs with less neutron leakage or could be used in power uprates to offer efficient safety margins. (authors)

  5. PWR-related integral safety experiments in the PKL 111 test facility SBLOCA under beyond-design-basis accident conditions

    SciTech Connect

    Weber, P.; Umminger, K.J.; Schoen, B.

    1995-09-01

    The thermal hydraulic behavior of a PWR during beyond-design-basis accident scenarios is of vital interest for the verification and optimization of accident management procedures. Within the scope of the German reactor safety research program experiments were performed in the volumetrically scaled PKL 111 test facility by Siemens/KWU. This highly instrumented test rig simulates a KWU-design PWR (1300 MWe). In particular, the latest tests performed related to a SBLOCA with additional system failures, e.g. nitrogen entering the primary system. In the case of a SBLOCA, it is the goal of the operator to put the plant in a condition where the decay heat can be removed first using the low pressure emergency core cooling system and then the residual heat removal system. The experimental investigation presented assumed the following beyond-design-basis accident conditions: 0.5% break in a cold leg, 2 of 4 steam generators (SGs) isolated on the secondary side (feedwater- and steam line-valves closed), filled with steam on the primary side, cooldown of the primary system using the remaining two steam generators, high pressure injection system only in the two loops with intact steam generators, if possible no operator actions to reach the conditions for residual heat removal system activation. Furthermore, it was postulated that 2 of the 4 hot leg accumulators had a reduced initial water inventory (increased nitrogen inventory), allowing nitrogen to enter the primary system at a pressure of 15 bar and nearly preventing the heat transfer in the SGs ({open_quotes}passivating{close_quotes} U-tubes). Due to this the heat transfer regime in the intact steam generators changed remarkably. The primary system showed self-regulating system effects and heat transfer improved again (reflux-condenser mode in the U-tube inlet region).

  6. Multi level optimization of burnable poison utilization for advanced PWR fuel management

    NASA Astrophysics Data System (ADS)

    Yilmaz, Serkan

    The objective of this study was to develop an unique methodology and a practical tool for designing burnable poison (BP) pattern for a given PWR core. Two techniques were studied in developing this tool. First, the deterministic technique called Modified Power Shape Forced Diffusion (MPSFD) method followed by a fine tuning algorithm, based on some heuristic rules, was developed to achieve this goal. Second, an efficient and a practical genetic algorithm (GA) tool was developed and applied successfully to Burnable Poisons (BPs) placement optimization problem for a reference Three Mile Island-1 (TMI-1) core. This thesis presents the step by step progress in developing such a tool. The developed deterministic method appeared to perform as expected. The GA technique produced excellent BP designs. It was discovered that the Beginning of Cycle (BOC) Kinf of a BP fuel assembly (FA) design is a good filter to eliminate invalid BP designs created during the optimization process. By eliminating all BP designs having BOC Kinf above a set limit, the computational time was greatly reduced since the evaluation process with reactor physics calculations for an invalid solution is canceled. Moreover, the GA was applied to develop the BP loading pattern to minimize the total Gadolinium (Gd) amount in the core together with the residual binding at End-of-Cycle (EOC) and to keep the maximum peak pin power during core depletion and Soluble boron concentration at BOC both less than their limit values. The number of UO2/Gd2O3 pins and Gd 2O3 concentrations for each fresh fuel location in the core are the decision variables and the total amount of the Gd in the core and maximum peak pin power during core depletion are in the fitness functions. The use of different fitness function definition and forcing the solution movement towards to desired region in the solution space accelerated the GA runs. Special emphasize is given to minimizing the residual binding to increase core lifetime as

  7. Effect of component aging on PWR control rod drive systems

    SciTech Connect

    Grove, E.; Gunther, W.; Sullivan, K.

    1992-01-01

    An aging assessment of PWR control rod drive (CRD) systems has been completed as part of the US NRC Nuclear Plant Aging Research (NPAR) Program. The design, construction, maintenance, and operation of the Babcock Wilcox (B W), Combustion Engineering (CE), and Westinghouse (W) systems were evaluated to determine the potential for degradation as each system ages. Operating experience data were evaluated to identify the predominant failure modes, causes, and effects. This, coupled with an assessment of the materials of construction and operating environment, demonstrate that each design is subject to degradation, which if left unchecked, could affect its safety function as the plant ages. An industry survey, conducted with the assistance of EPRI and NUMARC, identified current CRD system maintenance and inspection practices. The results of this survey indicate that some plants have performed system modifications, replaced components, or augmented existing preventive maintenance practices in response to system aging. The survey results also supported the operating experience data, which concluded that the timely replacement of degraded components, prior to failure, was not always possible using existing condition monitoring techniques. The recommendations presented in this study also include a discussion of more advanced monitoring techniques, which provide trendable results capable of detecting aging.

  8. Effect of component aging on PWR control rod drive systems

    SciTech Connect

    Grove, E.; Gunther, W.; Sullivan, K.

    1992-06-01

    An aging assessment of PWR control rod drive (CRD) systems has been completed as part of the US NRC Nuclear Plant Aging Research (NPAR) Program. The design, construction, maintenance, and operation of the Babcock & Wilcox (B & W), Combustion Engineering (CE), and Westinghouse (W) systems were evaluated to determine the potential for degradation as each system ages. Operating experience data were evaluated to identify the predominant failure modes, causes, and effects. This, coupled with an assessment of the materials of construction and operating environment, demonstrate that each design is subject to degradation, which if left unchecked, could affect its safety function as the plant ages. An industry survey, conducted with the assistance of EPRI and NUMARC, identified current CRD system maintenance and inspection practices. The results of this survey indicate that some plants have performed system modifications, replaced components, or augmented existing preventive maintenance practices in response to system aging. The survey results also supported the operating experience data, which concluded that the timely replacement of degraded components, prior to failure, was not always possible using existing condition monitoring techniques. The recommendations presented in this study also include a discussion of more advanced monitoring techniques, which provide trendable results capable of detecting aging.

  9. Integrity of PWR pressure vessels during overcooling accidents

    SciTech Connect

    Cheverton, R.D.; Iskander, S.K.; Whitman, G.D.

    1982-01-01

    The reactor pressure vessel in a pressurized water reactor is normally subjected to temperatures and pressures that preclude propagation of sharp, crack-like defects that might exist in the wall of the vessel. However, there is a class of postulated accidents, referred to as overcooling accidents, that can subject the pressure vessel to severe thermal shock while the pressure is substantial. As a result of such accidents, vessels containing high concentrations of copper and nickel, which enhance radiation embrittlement, may possess a potential for extensive propagation of preexistent inner surface flaws prior to the vessel's normal end of life. A state-of-the-art fracture-mechanics model was developed and has been used for conducting parametric analyses and for calculating several recorded PWR transients. Results of the latter analysis indicate that there may be some vessels that have a potential for failure in a few years if subjected to a Rancho Seco-type transient. However, the calculational model may be excessively conservative, and this possibility is under investigation.

  10. The determination of critical nuclides in PWR waste streams

    SciTech Connect

    De Goeyse, A.

    1993-12-31

    The safety studies concerning the final disposal of low- and intermediate-level radioactive waste take into consideration a series of long-lived radionuclides. The problem the producers have to cope with comes from the fact that those nuclides, which are mainly (pure) {beta} emitters or {alpha} emitters, cannot be measured by a direct current method such as gamma scanning. Their determination involves sophisticated radiochemical techniques which are difficult to implement by a producer on a routine basis for normal production waste. A current method for the determination of those nuclides in the waste streams produced by a nuclear power reactor consists in applying correlation factors or scaling factors between those critical nuclides and so called key radionuclides, which can be easily measured and are representative for the occurrence of activation products and fission products in the waste streams. In order to identify and define those correlation factors, ONDRAF/NIRAS, has subcontracted, in agreement with the waste producer (ELECTRABEL), a complete study to the engineering company BELGATOM (BA) for the different waste streams produced by the seven Belgian PWR plants.

  11. PWR (pressurized water reactor) pressurizer transient response: Final report

    SciTech Connect

    Murphy, S.I.

    1987-08-01

    To predict PWR pressurizer transients, Ahl proposed a three region model with a universal coefficient to represent condensation on the water surface. Specifically, this work checks the need for three regions and the modeling of the interfacial condensation coefficient. A computer model has been formulated using the basic mass and energy conservation laws. A two region vapor and liquid model was first used to predict transients run on a one-eleventh scale Freon pressurizer. These predictions verified the need for a second liquid region. As a result, a three region model was developed and used to predict full-scale pressurizer transients at TMI-2, Shippingport, and Stade. Full-scale pressurizer predictions verified the three region model and pointed out the shortcomings of Ahl's universal condensation coefficient. In addition, experiments were run using water at low pressure to study interface condensation. These experiments showed interface condensation to be significant only when spray flow is turned on; this result was incorporated in the final three region model.

  12. Assessment of PWR Steam Generator modelling in RELAP5/MOD2. International Agreement Report

    SciTech Connect

    Putney, J.M.; Preece, R.J.

    1993-06-01

    An assessment of Steam Generator (SG) modelling in the PWR thermal-hydraulic code RELAP5/MOD2 is presented. The assessment is based on a review of code assessment calculations performed in the UK and elsewhere, detailed calculations against a series of commissioning tests carried out on the Wolf Creek PWR and analytical investigations of the phenomena involved in normal and abnormal SG operation. A number of modelling deficiencies are identified and their implications for PWR safety analysis are discussed -- including methods for compensating for the deficiencies through changes to the input deck. Consideration is also given as to whether the deficiencies will still be present in the successor code RELAP5/MOD3.

  13. Fuel cycle cost, reactor physics and fuel manufacturing considerations for Erbia-bearing PWR fuel with > 5 wt% U-235 content

    SciTech Connect

    Franceschini, F.; Lahoda, E. J.; Kucukboyaci, V. N.

    2012-07-01

    The efforts to reduce fuel cycle cost have driven LWR fuel close to the licensed limit in fuel fissile content, 5.0 wt% U-235 enrichment, and the acceptable duty on current Zr-based cladding. An increase in the fuel enrichment beyond the 5 wt% limit, while certainly possible, entails costly investment in infrastructure and licensing. As a possible way to offset some of these costs, the addition of small amounts of Erbia to the UO{sub 2} powder with >5 wt% U-235 has been proposed, so that its initial reactivity is reduced to that of licensed fuel and most modifications to the existing facilities and equipment could be avoided. This paper discusses the potentialities of such a fuel on the US market from a vendor's perspective. An analysis of the in-core behavior and fuel cycle performance of a typical 4-loop PWR with 18 and 24-month operating cycles has been conducted, with the aim of quantifying the potential economic advantage and other operational benefits of this concept. Subsequently, the implications on fuel manufacturing and storage are discussed. While this concept has certainly good potential, a compelling case for its short-term introduction as PWR fuel for the US market could not be determined. (authors)

  14. WESTINGHOUSE 17X17 MOX PWR ASSEMBLY - WASTE PACKAGE CRITICALITY ANALYSIS (SCPB: N/A)

    SciTech Connect

    J.W. Davis

    1996-07-15

    This analysis is prepared by the Mined Geologic Disposal System (MGDS) Waste Package Development Department (WPDD) to compare the criticality potential of Westinghouse 17 x 17 mixed oxide (MOX) PWR fuel with the Design Basis spent nuclear fuel (SNF) analyzed previously (Ref. 5.1, 5.2). The basis of comparison will be the conceptual design Multi-Purpose Canister (MPC) PWR waste package concepts. The objectives of this evaluation are to show that the criticality potential of the MOX fuel is equal to or lower than the DBF or, if necessary, indicate what additional measures are required to make it so.

  15. Switching from deferred dismantling to immediate dismantling: the example of Chooz A, a French PWR

    SciTech Connect

    Grenouillet, Jean-Jacques

    2007-07-01

    Located in the north of France, close to Belgian border, Chooz A is the first PWR that was built in France from 1962 to 1967. When it was shutdown in 1991, a deferred dismantling strategy was selected. Further to an evolution of EDF decommissioning strategy in 2001, the decommissioning of the plant was accelerated by reducing the safe enclosure period to only a few years. Thus Chooz A will be the first PWR to be fully dismantled in France and it gives a good insight of what is needed to reactivate a plant for final dismantling after a safe enclosure period. (author)

  16. Categorization of PWR accident sequences and guidelines for fault trees: seismic initiators

    SciTech Connect

    Kimura, C.Y.

    1984-09-01

    This study developed a set of dominant accident sequences that could be applied generically to domestic commercial PWRs as a standardized basis for a probabilistic seismic risk assessment. This was accomplished by ranking the Zion 1 accident sequences. The pertinent PWR safety systems were compared on a plant-by-plant basis to determine the applicability of the dominant accident sequences of Zion 1 to other PWR plants. The functional event trees were developed to describe the system functions that must work or not work in order for a certain accident sequence to happen, one for pipe breaks and one for transients.

  17. Methodology for embedded transport core calculation

    NASA Astrophysics Data System (ADS)

    Ivanov, Boyan D.

    The progress in the Nuclear Engineering field leads to developing new generations of Nuclear Power Plants (NPP) with complex rector core designs, such as cores loaded partially with mixed-oxide (MOX) fuel, high burn-up loadings, and cores with advanced designs of fuel assemblies and control rods. Such heterogeneous cores introduce challenges for the diffusion theory that has been used for several decades for calculations of the current Pressurized Water Rector (PWR) cores. To address the difficulties the diffusion approximation encounters new core calculation methodologies need to be developed by improving accuracy, while preserving efficiency of the current reactor core calculations. In this thesis, an advanced core calculation methodology is introduced, based on embedded transport calculations. Two different approaches are investigated. The first approach is based on embedded finite element (FEM), simplified P3 approximation (SP3), fuel assembly (FA) homogenization calculation within the framework of the diffusion core calculation with NEM code (Nodal Expansion Method). The second approach involves embedded FA lattice physics eigenvalue calculation based on collision probability method (CPM) again within the framework of the NEM diffusion core calculation. The second approach is superior to the first because most of the uncertainties introduced by the off-line cross-section generation are eliminated.

  18. PWR FLECHT SEASET 21-rod bundle flow blockage task data and analysis report. NRC/EPRI/Westinghouse Report No. 11. Appendices K-P

    SciTech Connect

    Loftus, M.J.; Hochreiter, L.E.; Lee, N.; McGuire, M.F.; Wenzel, A.H.; Valkovic, M.M.

    1982-09-01

    This report presents data and limited analysis from the 21-Rod Bundle Flow Blockage Task of the Full-Length Emergency Cooling Heat Transfer Separate Effects and Systems Effects Test Program (FLECHT SEASET). The tests consisted of forced and gravity reflooding tests utilizing electrical heater rods with a cosine axial power profile to simulate PWR nuclear core fuel rod arrays. Steam cooling and hydraulic characteristics tests were also conducted. These tests were utilized to determine effects of various flow blockage configurations (shapes and distributions) on reflooding behavior, to aid in development/assessment of computational models in predicting reflooding behavior of flow blockage configurations, and to screen flow blockage configurations for future 163-rod flow blockage bundle tests.

  19. Performance evaluation of two-stage fuel cycle from SFR to PWR

    SciTech Connect

    Fei, T.; Hoffman, E.A.; Kim, T.K.; Taiwo, T.A.

    2013-07-01

    One potential fuel cycle option being considered is a two-stage fuel cycle system involving the continuous recycle of transuranics in a fast reactor and the use of bred plutonium in a thermal reactor. The first stage is a Sodium-cooled Fast Reactor (SFR) fuel cycle with metallic U-TRU-Zr fuel. The SFRs need to have a breeding ratio greater than 1.0 in order to produce fissile material for use in the second stage. The second stage is a PWR fuel cycle with uranium and plutonium mixed oxide fuel based on the design and performance of the current state-of-the-art commercial PWRs with an average discharge burnup of 50 MWd/kgHM. This paper evaluates the possibility of this fuel cycle option and discusses its fuel cycle performance characteristics. The study focuses on an equilibrium stage of the fuel cycle. Results indicate that, in order to avoid a positive coolant void reactivity feedback in the stage-2 PWR, the reactor requires high quality of plutonium from the first stage and minor actinides in the discharge fuel of the PWR needs to be separated and sent back to the stage-1 SFR. The electricity-sharing ratio between the 2 stages is 87.0% (SFR) to 13.0% (PWR) for a TRU inventory ratio (the mass of TRU in the discharge fuel divided by the mass of TRU in the fresh fuel) of 1.06. A sensitivity study indicated that by increasing the TRU inventory ratio to 1.13, The electricity generation fraction of stage-2 PWR is increased to 28.9%. The two-stage fuel cycle system considered in this study was found to provide a high uranium utilization (>80%). (authors)

  20. Crack growth rates of nickel alloy welds in a PWR environment.

    SciTech Connect

    Alexandreanu, B.; Chopra, O. K.; Shack, W. J.; Energy Technology

    2006-05-31

    In light water reactors (LWRs), vessel internal components made of nickel-base alloys are susceptible to environmentally assisted cracking. A better understanding of the causes and mechanisms of this cracking may permit less conservative estimates of damage accumulation and requirements on inspection intervals. A program is being conducted at Argonne National Laboratory to evaluate the resistance of Ni alloys and their welds to environmentally assisted cracking in simulated LWR coolant environments. This report presents crack growth rate (CGR) results for Alloy 182 shielded-metal-arc weld metal in a simulated pressurized water reactor (PWR) environment at 320 C. Crack growth tests were conducted on 1-T compact tension specimens with different weld orientations from both double-J and deep-groove welds. The results indicate little or no environmental enhancement of fatigue CGRs of Alloy 182 weld metal in the PWR environment. The CGRs of Alloy 182 in the PWR environment are a factor of {approx}5 higher than those of Alloy 600 in air under the same loading conditions. The stress corrosion cracking for the Alloy 182 weld is close to the average behavior of Alloy 600 in the PWR environment. The weld orientation was found to have a profound effect on the magnitude of crack growth: cracking was found to propagate faster along the dendrites than across them. The existing CGR data for Ni-alloy weld metals have been compiled and evaluated to establish the effects of key material, loading, and environmental parameters on CGRs in PWR environments. The results from the present study are compared with the existing CGR data for Ni-alloy welds to determine the relative susceptibility of the specific Ni-alloy weld to environmentally enhanced cracking.

  1. Management of thermal peaking factors in CONFU-B PWR assemblies using neutron poisons and tailored enrichment

    SciTech Connect

    Visosky, M.; Hejzlar, P.; Kazimi, M.

    2006-07-01

    CONFU-B assemblies are PWR assemblies containing standard Uranium fuel rods and TRU bearing inert material fuel rods and are designed to achieve net TRU destruction over a 4.5-year irradiation. These highly heterogeneous assemblies tend to exhibit large intra-assembly power peaking factors (IAPPF). Neutronic strategies to reduce IAPPF are developed. The IAPPF are calculated at the assembly level using CASMO4, and these are used to calculate the most restrictive thermal margin (the Minimum Departure from Nucleate Boiling Ratio, MDNBR) using a whole-core VIPRE-01 model. This paper examines two strategies to manage the thermal margin of a CONFU-B assembly while retaining the TRU destruction performance: use of neutron poisons and tailored enrichment schemes. Burnable poisons can be used to suppress BOL reactivity of fresh CONFU-B assemblies with only minor impact on MDNBR and TRU destruction performance. Tailored enrichment, along with the use of soluble boron, can achieve significant improvements in MDNBR, but at some cost to TRU destruction performance. (authors)

  2. Artificial neural network prediction of PWR critical boron concentration

    SciTech Connect

    Wendt, S.E.; Maldonado, G.I.; Bartlett, E.B.

    1995-12-31

    The direct calculation of core parameters such as k{sub eff} and pin power peaks for light water reactors is ordinarily accomplished by numerically solving the neutron diffusion equation. Despite the rapid advances in computer architecture and algorithm development, further calculational speedups are always in great demand. One example of such an application is nuclear fuel management optimization, where the core attributes of tens of thousands of loading pattern candidates must typically be evaluated over the fuel cycle. If an artificial neural network (ANN) could be trained to accurately model the neutronic behavior of a core, a substantial time savings could be realized in the prediction of core parameters. Such an ANN could be exploited in at least two ways: 1. The a priori training of an ANN model could be tailored to address a specific plant and its corresponding licensing core neutronics software. 2. Once trained to within acceptable accuracy guidelines, an ANN model could provide the luxury of nearly instantaneous evaluations of core parameters. Recent publications by Kim et al. on core parameter prediction via ANNs have revealed a variety of promising results, which, in part, motivated our studies. Kim proved that a solution was possible; however, the large size and complexity of such a model can lead to memorization instead of generalization of the problem`s solution. Thus, the purpose of this work was to show that a much smaller ANN could predict a global core parameter such as the critical boron concentration over a wide range of training and validation data. The successful modeling of this problem with a much smaller ANN is considered to be a significant highlight of this study. This work employed Studsvik of America`s SOA1 Database, which proved to be useful for ANN training and validation.

  3. High-temperature compatibility between liquid metal as PWR fuel gap filler and stainless steel and high-density concrete

    NASA Astrophysics Data System (ADS)

    Wongsawaeng, Doonyapong; Jumpee, Chayanit; Jitpukdee, Manit

    2014-08-01

    In conventional nuclear fuel rods for light-water reactors, a helium-filled as-fabricated gap between the fuel and the cladding inner surface accommodates fuel swelling and cladding creep down. Because helium exhibits a very low thermal conductivity, it results in a large temperature rise in the gap. Liquid metal (LM; 1/3 weight portion each of lead, tin, and bismuth) has been proposed to be a gap filler because of its high thermal conductivity (∼100 times that of He), low melting point (∼100 °C), and lack of chemical reactivity with UO2 and water. With the presence of LM, the temperature drop across the gap is virtually eliminated and the fuel is operated at a lower temperature at the same power output, resulting in safer fuel, delayed fission gas release and prevention of massive secondary hydriding. During normal reactor operation, should an LM-bonded fuel rod failure occurs resulting in a discharge of liquid metal into the bottom of the reactor pressure vessel, it should not corrode stainless steel. An experiment was conducted to confirm that at 315 °C, LM in contact with 304 stainless steel in the PWR water chemistry environment for up to 30 days resulted in no observable corrosion. Moreover, during a hypothetical core-melt accident assuming that the liquid metal with elevated temperature between 1000 and 1600 °C is spread on a high-density concrete basement of the power plant, a small-scale experiment was performed to demonstrate that the LM-concrete interaction at 1000 °C for as long as 12 h resulted in no penetration. At 1200 °C for 5 h, the LM penetrated a distance of ∼1.3 cm, but the penetration appeared to stop. At 1400 °C the penetration rate was ∼0.7 cm/h. At 1600 °C, the penetration rate was ∼17 cm/h. No corrosion based on chemical reactions with high-density concrete occurred, and, hence, the only physical interaction between high-temperature LM and high-density concrete was from tiny cracks generated from thermal stress. Moreover

  4. Topical report on actinide-only burnup credit for PWR spent nuclear fuel packages. Revision 1

    SciTech Connect

    None, None

    1997-04-01

    A methodology for performing and applying nuclear criticality safety calculations, for PWR spent nuclear fuel (SNF) packages with actinide-only burnup credit, is described. The changes in the U-234, U-235, U-236, U-238, Pu-238, Pu-239, Pu-240, Pu-241, Pu-242, and Am-241 concentration with burnup are used in burnup credit criticality analyses. No credit for fission product neutron absorbers is taken. The methodology consists of five major steps. (1) Validate a computer code system to calculate isotopic concentrations of SNF created during burnup in the reactor core and subsequent decay. A set of chemical assay benchmarks is presented for this purpose as well as a method for assessing the calculational bias and uncertainty, and conservative correction factors for each isotope. (2) Validate a computer code system to predict the subcritical multiplication factor, k{sub eff}, of a spent nuclear fuel package. Fifty-seven UO{sub 2}, UO{sub 2}/Gd{sub 2}O{sub 3}, and UO{sub 2}/PuO{sub 2} critical experiments have been selected to cover anticipated conditions of SNF. The method uses an upper safety limit on k{sub eff} (which can be a function of the trending parameters) such that the biased k{sub eff}, when increased for the uncertainty is less than 0.95. (3) Establish bounding conditions for the isotopic concentration and criticality calculations. Three bounding axial profiles have been established to assure the ''end effect'' is accounted for conservatively. (4) Use the validated codes and bounding conditions to generate package loading criteria (burnup credit loading curves). Burnup credit loading curves show the minimum burnup required for a given initial enrichment. The utility burnup record is compared to this requirement after the utility accounts for the uncertainty in its record. Separate curves may be generated for each assembly design, various minimum cooling times and burnable absorber histories. (5) Verify that SNF assemblies meet the package loading criteria

  5. DOSE RATES FOR WESTINGHOUSE 17X17 MOX PWR SNF IN A WASTE PACKAGE (SCPB: N/A)

    SciTech Connect

    T.L. Lotz

    1997-01-29

    This analysis is prepared by the Mined Geologic Disposal System (MGDS) Waste Package Development Department (WPDD) to estimate the dose rate on and near the surface a Multi-Purpose Canister (MPC) PWR waste package (WP) which is loaded with Westinghouse 17 x 17 mixed oxide (MOX) PWR fuel. The 21 PWR MPC WP is used to provide an upper bound for waste package designs since the 12 PWR MPC WP will have a smaller source term and an equivalent amount of shielding. the objectives of this evaluation are to calculate the requested dose rate(s) and document the calculation in a fashion to allow comparisons to other waste forms and WP designs at a future time.

  6. Analysis of WWER-440 and PWR RPV welds surveillance data to compare irradiation damage evolution

    NASA Astrophysics Data System (ADS)

    Debarberis, L.; Acosta, B.; Zeman, A.; Sevini, F.; Ballesteros, A.; Kryukov, A.; Gillemot, F.; Brumovsky, M.

    2006-04-01

    It is known that for Russian-type and Western water reactor pressure vessel steels there is a similar degradation in mechanical properties during equivalent neutron irradiation. Available surveillance results from WWER and PWR vessels are used in this article to compare irradiation damage evolution for the different reactor pressure vessel welds. The analysis is done through the semi-mechanistic model for radiation embrittlement developed by JRC-IE. Consistency analysis with BWR vessel materials and model alloys has also been performed within this study. Globally the two families of studied materials follow similar trends regarding the evolution of irradiation damage. Moreover in the high fluence range typical of operation of WWER the radiation stability of these vessels is greater than the foreseen one for PWR.

  7. Some thermalhydraulics of closure head adapters in a 3 loops PWR

    SciTech Connect

    Hoffmann, F.; Daubert, O.; Hecker, M.

    1995-09-01

    In 1993 a R&D action, based on numerical simulations and experiments on PWR`s upper head was initiated. This paper presents the test facility TRAVERSIN (a scale model of a 900 MW PWR adapter) and the calculations performed on the geometry of different upper head sections with the Thermalhydraulic Finite Element Code N3S used for 2D and 3D computations. The paper presents the method followed to bring the adapter and upper head study to a successful conclusion. Two complementary approaches are performed to obtain global results on complete fluid flow in the upper head and local results on the flow around the adapters of closure head. A validation test case of these experimental and numerical tools is also presented.

  8. The electrochemistry in 316SS crevices exposed to PWR-relevant conditions

    NASA Astrophysics Data System (ADS)

    Vankeerberghen, M.; Weyns, G.; Gavrilov, S.; Henshaw, J.; Deconinck, J.

    2009-04-01

    The chemical and electrochemical conditions within a crevice of Type 316 stainless steel in boric acid-lithium hydroxide solutions under PWR-relevant conditions were modelled with a computational electrochemistry code. The influence of various variables: dissolved hydrogen, boric acid, lithium hydroxide concentration, crevice length, and radiation dose rate was studied. It was found with the model that 25 ccH 2/kg (STP) was sufficient to remain below an electrode potential of -230 mV she, commonly accepted sufficient to prevent stress corrosion cracking under BWR conditions. In a PWR plant various operational B-Li cycles are possible but it was found that the choice of the cycle did not significantly influence the model results. It was also found that a hydrogen level of 50 ccH 2/kg (STP) would be needed to avoid substantial lowering of the pH inside a crevice.

  9. Preliminary assessment of PWR Steam Generator modelling in RELAP5/MOD3. International Agreeement Report

    SciTech Connect

    Preece, R.J.; Putney, J.M.

    1993-07-01

    A preliminary assessment of Steam Generator (SG) modelling in the PWR thermal-hydraulic code RELAP5/MOD3 is presented. The study is based on calculations against a series of steady-state commissioning tests carried out on the Wolf Creek PWR over a range of load conditions. Data from the tests are used to assess the modelling of primary to secondary side heat transfer and, in particular, to examine the effect of reverting to the standard form of the Chen heat transfer correlation in place of the modified form applied in RELAP5/MOD2. Comparisons between the two versions of the code are also used to show how the new interphase drag model in RELAP5/MOD3 affects the calculation of SG liquid inventory and the void fraction profile in the riser.

  10. Application of the RCP01 Code to Depletion of a PWR Spent Nuclear Fuel Sample

    SciTech Connect

    Joo, Hansem

    2002-01-01

    An essential component of a proposed burnup credit methodology for commercial PWR spent nuclear fuel (SNF) is the validation of the tools used for isotopic and criticality calculations. A number of benchmark experiments have been analyzed to establish the validation of the tools and to determine biases and corrections. To benchmark the RCP01 Monte Carlo computer code, an isotopic validation study was conducted for one of the benchmark experiments, a SNF sample taken from the Calvert Cliffs PWR Unit-1 (CCPU1). Modeling considerations and nuclear data associated with the RCP01 transport/depletion calculations are discussed. The accuracy of RCP01 calculations is demonstrated to be very good when RCP01 results are compared to destructive chemical assay data for major actinides and important fission products in the SNF sample.

  11. Generation and behavior of metal oxide colloids in PWR steam systems

    SciTech Connect

    Varsanik, R.G.

    1984-10-01

    This work reviews the curently available literature and research work on the generation and behavior of metal oxide colloids in PWR steam systems. The work of E. Matijevic et al on the generation and adhesion of iron and copper oxides is described. The role of colloid chemistry in the control of plant sludge and corrosion products is described. Factors affecting the adherence and re-entrainment of colloidal metal oxides along with possible methods for the control of metal oxide deposition are reviewed.

  12. MELCOR model for an experimental 17x17 spent fuel PWR assembly.

    SciTech Connect

    Cardoni, Jeffrey

    2010-11-01

    A MELCOR model has been developed to simulate a pressurized water reactor (PWR) 17 x 17 assembly in a spent fuel pool rack cell undergoing severe accident conditions. To the extent possible, the MELCOR model reflects the actual geometry, materials, and masses present in the experimental arrangement for the Sandia Fuel Project (SFP). The report presents an overview of the SFP experimental arrangement, the MELCOR model specifications, demonstration calculation results, and the input model listing.

  13. Some Aspects of Cost/ Benefit Analysis for In-Service Inspection of PWR Steam Generators

    SciTech Connect

    Zima, G. E.; Lyon, G. H.; Doctor, P. G.; Hoenes, G. R.; Petty, S. E.; Weakley, S. A.

    1981-05-01

    This report discusses a number of aspects of cost/benefit (C/B) analysis for in-service inspection (lSI} of pressurized water reactor (PWR) steam generators (SGs) and identifies several problem areas that must be addressed prior to a full C/B analysis capability. Following a brief review of the impact of SG problems on the productivity of PWR units and of the scope and variability of SG problems among U.S. PWRs, various occupational implications of SG lSI are considered, namely manpower, time, and rad exposure. The opportunities provided by refueling outages in respect to lSI frequency and work time windows are reviewed. Indices for characterizing the nondestructive testing {NDT) information, rad exposure, $ impact, and manpower and time attributes of single ISIs and a series of ISIs over an arbitrary evaluation period are presented and calculated for a number of lSI cases using SG parameters for three typical PWR units. A comparison of the $ impact of unscheduled outages attributable to SG problems with the $ cost of ambitious lSI strategies indicates that the $ cost is virtually negligible for well-planned ISis. Considering the ALARA constraint on occupational rad exposure, the skilled manpower pool for NDT work appears to be the principal factor limiting lSI scope and frequency. Analysis of the manpower and time requirements for inspection of a 40-unit PWR population indicates, however, that an lSI strategy embodying two campaigns per year and a total population inspection within a 2-year interval is not far beyond current capabilities.

  14. Primary water chemistry improvement for radiation exposure reduction at Japanese PWR Plants

    SciTech Connect

    Nishizawa, Eiichi

    1995-03-01

    Radiation exposure during the refueling outages at Japanese Pressurized Water Reactor (PWR) Plants has been gradually decreased through continuous efforts keeping the radiation dose rates at relatively low level. The improvement of primary water chemistry in respect to reduction of the radiation sources appears as one of the most important contributions to the achieved results and can be classified by the plant operation conditions as follows

  15. On the Application of CFD Modeling for the Prediction of the Degree of Mixing in a PWR During a Boron Dilution Transient

    SciTech Connect

    Lycklama, Jan-Aiso; Hoehne, Thomas

    2006-07-01

    In a Pressurized Water Reactor, negative reactivity is present in the core by means of Boric acid as a soluble neutron absorber in the coolant water. During a so-called Boron Dilution Transient (BDT), a de-borated slug of coolant water is transported from the cold leg into the reactor vessel, and the borated coolant water is diluted by mixing with this un-borated water. The resulting decrease in the boron concentration leads to an insertion of positive reactivity in the core, which may lead to a reactivity excursion. The associated power peak may damage the fuel rods. The mixing of borated and un-borated water in downcomer and lower plenum is an important process, because it mitigates the degree of reactivity insertion. In the present study the application of Computational Fluid Dynamics (CFD) for the prediction of this mixing of un-borated with borated water in the RPV has been assessed. The analyses have been compared with the measurement data from the Rossendorf coolant mixing model (ROCOM) experiment. The ROCOM test facility represents the primary cooling system of a KONVOI type of PWR (1300 MW{sub el}). In spite of the complicated spatial, temporal, and geometrical aspects of the flow in the RPV, the agreement between the calculated and the experimental data is good. The CFD model tends to slightly under predict the degree of mixing in the RPV resulting in a slight under-prediction of the boron concentration at the core. (authors)

  16. Amorphous and Nanocrystalline High Temperature Magnetic Material for PWR

    DTIC Science & Technology

    2006-03-01

    losses. Finite element software packages including FEMLAB©, FEMME © and FLEXPDE© were investigated to determine the fabrication parameters for the...analysis was based on a combination of NiZn ferrite as a core material with a spiral Cu coil. The geometry used in FEMME to simulate the effects of...various parameters and frequencies is shown in Figure III.4.5. FEMME © was chosen because it was simple to use and a planar inductor can be simulated

  17. Determination of soluble chromium in simulated PWR coolant by differential-pulse adsorptive stripping voltammetry.

    PubMed

    Torrance, K; Gatford, C

    1987-11-01

    An analytical method has been developed for the determination of dissolved chromium at concentrations less than 2 mug/l. in PWR coolant by differential-pulse adsorptive stripping voltammetry at a hanging mercury drop electrode. Concentrations above 2 mug/l. can be determined by appropriate dilution of the sample. The method is based on measurement of the current associated with reduction of a chromium(III)-DTPA (diethylenetriaminepenta-acetic acid) complex adsorbed at the surface of the mercury drop. The effects of boric acid, pH, DTPA concentration, accumulation potential and time were investigated together with the oxidation state of the chromium. No interference was observed from other transition metal ions expected to be present in PWR coolant. No alternative chemical technique of similar sensitivity was available for comparison with the results obtained in solutions containing <1 mug/l. chromium. Recoveries from simulated coolant solutions were greater than 95% and the relative standard deviations for single determinations were in the range 12-25%. The statistical limit of detection at the 95% confidence level was 0.023 mug/l. This method of analysis should prove valuable in corrosion studies and is uniquely capable of following the changes in soluble chromium concentration in PWR coolant that follow operational changes in the reactor.

  18. Differential pulse stripping voltammetry for the determination of nickel and cobalt in simulated PWR coolant.

    PubMed

    Torrance, K; Gatford, C

    1985-04-01

    The determination of ionic nickel and cobalt in simulated PWR coolant at concentrations below 1 microg/l. by differential pulse stripping voltammetry at a hanging mercury-drop electrode has been investigated. The high sensitivity for these ions results from the adsorptive accumulation of their dimethylglyoximate complexes on the mercury drop. Boric acid does not interfere and if the samples are adjusted to pH 9 with an ammonia-ammonium chloride buffer, both nickel and cobalt can be determined in the same run. The relative standard deviations at concentrations below 2 microg/l. are of the order of 5-7% and the limits of detection for nickel and cobalt are about 8 and 2 ng/l. respectively. These performance statistics show that this method is the most sensitive method currently available for determination of soluble nickel and cobalt in PWR coolant and it should prove to be most valuable in any corrosion studies of the materials of construction of the primary circuit of a PWR.

  19. PWR ENDF/B-VII cross-section libraries for ORIGEN-ARP

    SciTech Connect

    McGraw, C.; Ilas, G.

    2012-07-01

    New pressurized water reactor (PWR) cross-section libraries were generated for use with the ORIGEN-ARP depletion sequence in the SCALE nuclear analysis code system. These libraries are based on ENDF/B-VII nuclear data and were generated using the two-dimensional depletion sequence, TRITON/NEWT, in SCALE 6.1. The libraries contain multiple burnup-dependent cross-sections for seven PWR fuel designs, with enrichments ranging from 1.5 to 6 wt% {sup 235}U. The burnup range has been extended from the 72 GWd/MTU used in previous versions of the libraries to 90 GWd/MTU. Validation of the libraries using radiochemical assay measurements and decay heat measurements for PWR spent fuel showed good agreement between calculated and experimental data. Verification against detailed TRITON simulations for the considered assembly designs showed that depletion calculations performed in ORIGEN-ARP with the pre-generated libraries provide similar results as obtained with direct TRITON depletion, while greatly reducing the computation time. (authors)

  20. Calculation of the radionuclides in PWR spent fuel samples for SFR experiment planning.

    SciTech Connect

    Naegeli, Robert Earl

    2004-06-01

    This report documents the calculation of radionuclide content in the pressurized water reactor (PWR) spent fuel samples planned for use in the Spent Fuel Ratio (SPR) Experiments at Sandia National Laboratories, Albuquerque, New Mexico (SNL) to aid in experiment planning. The calculation methods using the ORIGEN2 and ORIGEN-ARP computer codes and the input modeling of the planned PWR spent fuel from the H. B. Robinson and the Surry nuclear power plants are discussed. The safety hazards for the calculated nuclide inventories in the spent fuel samples are characterized by the potential airborne dose and by the portion of the nuclear facility hazard category 2 and 3 thresholds that the experiment samples would present. In addition, the gamma ray photon energy source for the nuclide inventories is tabulated to facilitate subsequent calculation of the direct and shielded dose rates expected from the samples. The relative hazards of the high burnup 72 gigawatt-day per metric ton of uranium (GWd/MTU) spent fuel from H. B. Robinson and the medium burnup 36 GWd/MTU spent fuel from Surry are compared against a parametric calculation of various fuel burnups to assess the potential for higher hazard PWR fuel samples.

  1. Total evaluation of in bundle void fraction measurement test of PWR fuel assembly

    SciTech Connect

    Hori, Keiichi; Miyazaki, Keiji; Akiyama, Yoshiei; Nishioka, Hiromasa; Takeda, Naoki

    1996-08-01

    Nuclear Power Engineering Corporation is performing the various proof or verification tests on safety and reliability of nuclear power plants under the sponsorship of the Ministry of International Trade and Industry. As one program of these Japanese national projects, an in bundle void fraction measurement test of a pressurized water reactor (PWR) fuel assembly was started in 1987 and finished at the end of 1994. The experiments were performed using the 5 x 5 square array rod bundle test sections. The rod bundle test section simulates the partial section and full length of a 17 x 17 type Japanese PWR fuel assembly. A distribution of subchannel averaged void fraction in a rod bundle test section was measured by the gamma-ray attenuation method using the stationary multi beam systems. The additional single channel test was performed to obtain the required information for the calibration of the rod bundle test data and the assessment of the void prediction method. Three test rod bundles were prepared to analyze an axial power distribution effect, an unheated rod effect, and a grid spacer effect. And, the obtained data were used for the assessment of the void prediction method relevant to the subchannel averaged void fraction of PWR fuel assemblies. This paper describes the outline of the experiments, the evaluation of the experimental data and the assessment of void prediction method.

  2. Sensitivity studies of seismic risk models. Final report. [PWR

    SciTech Connect

    Ravindra, M.K.; Banon, H.; Sues, R.H.; Thrasher, R.D.

    1984-06-01

    Recent PRA studies have used the Zion Method for estimating the seismic risks of nuclear power plants. During the course of these studies and in the subsequent regulatory and peer reviews, several questions were raised regarding the sensitivity of risk estimates. The present report has addressed these concerns with the objective of deriving generic conclusions. Sensitivity of seismically-induced severe core damage frequencies to different modeling assumptions was investigated using the Zion and Indian Point Unit 2 probabilistic safety studies as base cases. These included the effects of peak acceleration truncation, fragility modeling, dependence between component failures, and the significance of gross design and construction errors.

  3. French PWRs: In-core fuel management evolution and future direction

    SciTech Connect

    Rome, M. ); LeBars, M. )

    1993-01-01

    French pressurized water reactor (PWR) fuel management has been carried out until now with the objective of cycle cost reduction. This paper presents the feasibility study of an 18 month cycle for 1300-MW PWRs, three-batch fuel management with 4.00% enrichment, performed by EdF in 1992; the qualifications of core calculation methodology with gadolinia integrated burnable neutron absorbers through the Gedeon critical experiment carried out in the Melusine reactor in Grenoble; and the progress in core calculational methods, which were carried out to determine core safety with the increase in cycle length to 18 months.

  4. Interfacial transfer in annular dispersed flow. [PWR; BWR

    SciTech Connect

    Ishii, M.; Kataoka, I.

    1982-01-01

    The interfacial drag, droplet entrainment, droplet deposition and droplet-size distributions are important for detailed mechanistic modeling of annular dispersed two-phase flow. In view of this, recently developed correlations for these parameters are presented and discussed in this paper. The onset of droplet entrainment significantly alters the mechanisms of mass, momentum, and energy transfer between the film and gas core flow as well as the transfer between the two-phase mixture and the wall. By assuming the roll wave entrainment mechanism, the correlations for the amount of entrained droplet as well as for the droplet-size distribution have been obtained from a simple model in collaboration with a large number of data. Then the rate equations for entrainment and deposition have been developed. The drag correlations relevant to the droplet transfer is also presented. The comparison of the correlations to various data show satisfactory agreement.

  5. Modelling of molten fuel/concrete interactions. [PWR; BWR

    SciTech Connect

    Muir, J. F.; Benjamin, A. S.

    1980-01-01

    A computer program modelling the interaction between molten core materials and structural concrete (CORCON) is being developed to provide quantitative estimates of fuel-melt accident consequences suitable for risk assessment of light water reactors. The principal features of CORCON are reviewed. Models developed for the principal interaction phenomena, inter-component heat transfer, concrete erosion, and melt/gas chemical reactions, are described. Alternative models for the controlling phenomenon, heat transfer from the molten pool to the surrounding concrete, are presented. These models, formulated in conjunction with the development of CORCON, are characterized by the presence or absence of either a gas film or viscous layer of molten concrete at the melt/concrete interface. Predictions of heat transfer based on these models compare favorably with available experimental data.

  6. Hydrodynamics of annular-dispersed flow. [PWR; BWR

    SciTech Connect

    Ishii, M.; Kataoka, I.

    1982-01-01

    The interfacial drag, droplet entrainment, and droplet size distributions are important for detailed mechanistic modeling of annular dispersed two-phase flow. In view of this, recently developed correlations for these parameters are presented and discussed in this paper. The drag correlations for multiple fluid particle systems have been developed from a similarity hypothesis based on the mixture viscosity model. The results show that the drag coefficient depends on the particle Reynolds number and droplet concentration. The onset on droplet entrainment significantly alters the mechanisms of mass, momentum, and energy transfer between the film and gas core flow as well as the transfer between the two-phase mixture and the wall. By assuming the roll wave entrainment mechanism, the correlations for the amount of entrained droplet as well as for the droplet size distribution have been obtained from a simple model in collaboration with a large number of data.

  7. Method and apparatus for monitoring two-phase flow. [PWR

    DOEpatents

    Sheppard, J.D.; Tong, L.S.

    1975-12-19

    A method and apparatus for monitoring two-phase flow is provided that is particularly related to the monitoring of transient two-phase (liquid-vapor) flow rates such as may occur during a pressurized water reactor core blow-down. The present invention essentially comprises the use of flanged wire screens or similar devices, such as perforated plates, to produce certain desirable effects in the flow regime for monitoring purposes. One desirable effect is a measurable and reproducible pressure drop across the screen. The pressure drop can be characterized for various known flow rates and then used to monitor nonhomogeneous flow regimes. Another useful effect of the use of screens or plates in nonhomogeneous flow is that such apparatus tends to create a uniformly dispersed flow regime in the immediate downstream vicinity. This is a desirable effect because it usually increases the accuracy of flow rate measurements determined by conventional methods.

  8. Composite Cores

    NASA Technical Reports Server (NTRS)

    1990-01-01

    Spang & Company's new configuration of converter transformer cores is a composite of gapped and ungapped cores assembled together in concentric relationship. The net effect of the composite design is to combine the protection from saturation offered by the gapped core with the lower magnetizing requirement of the ungapped core. The uncut core functions under normal operating conditions and the cut core takes over during abnormal operation to prevent power surges and their potentially destructive effect on transistors. Principal customers are aerospace and defense manufacturers. Cores also have applicability in commercial products where precise power regulation is required, as in the power supplies for large mainframe computers.

  9. INTERCOMPARISON OF RESULTS FOR A PWR ROD EJECTION ACCIDENT

    SciTech Connect

    DIAMOND,D.J.; ARONSON,A.; JO,J.; AVVAKUMOV,A.; MALOFEEV,V.; SIDOROV,V.; FERRARESI,P.; GOUIN,C.; ANIEL,S.; ROYER,M.E.

    1999-10-01

    This study is part of an overall program to understand the uncertainty in best-estimate calculations of the local fuel enthalpy during the rod ejection accident. Local fuel enthalpy is used as the acceptance criterion for this design-basis event and can also be used to estimate fuel damage for the purpose of determining radiological consequences. The study used results from neutron kinetics models in PARCS, BARS, and CRONOS2, codes developed in the US, the Russian Federation, and France, respectively. Since BARS uses a heterogeneous representation of the fuel assembly as opposed to the homogeneous representations in PARCS and CRONOS, the effect of the intercomparison was primarily to compare different intra-assembly models. Quantitative comparisons for core power, reactivity, assembly fuel enthalpy and pin power were carried out. In general the agreement between methods was very good providing additional confidence in the codes and providing a starting point for a quantitative assessment of the uncertainty in calculated fuel enthalpy using best-estimate methods.

  10. Impact of radiation embrittlement on integrity of pressure vessel supports for two PWR plants

    SciTech Connect

    Cheverton, R.D.; Pennell, W.E.; Robinson, G.C.; Nanstad, R.K.

    1989-01-01

    Recent data from the HFIR vessel surveillance program indicate a substantial radiation embrittlement rate effect at low irradiation temperatures (/approximately/120/degree/F) for A212-B, A350-LF3, A105-II, and corresponding welds. PWR vessel supports are fabricated of similar materials and are subjected to the same low temperatures and fast neutron fluxes (10/sup 8/ to 10/sup 9/ neutrons/cm/sup 2//center dot/s, E > 1.0 MeV) as those in the HFIR vessel. Thus, the embrittlement rate of these structures may be greater than previously anticipated. A study sponsored by the NRC is under way at ORNL to determine the impact of the rate effect on PWR vessel-support life expectancy. The scope includes the interpretation and application of the HFIR data, a survey of all light-water-reactor vessel support designs, and a structural and fracture-mechanics analysis of the supports for two specific PWR plants of particular interest with regard to a potential for support failure as a result of propagation of flaws. Calculations performed thus far indicate best-estimate critical flaw sizes, corresponding to 32 EFPY, of /approximately/0.2 in. for one plant and /approximately/0.4 in. for the other. These flaw sizes are small enough to be of concern. However, it appears that low-cycle fatigue is not a viable mechanism for creation of flaws of this size, and thus, presumably, such flaws would have to exist at the time of fabrication. 59 refs., 128 figs., 49 tabs.

  11. PWR Facility Dose Modeling Using MCNP5 and the CADIS/ADVANTG Variance-Reduction Methodology

    SciTech Connect

    Blakeman, Edward D; Peplow, Douglas E.; Wagner, John C; Murphy, Brian D; Mueller, Don

    2007-09-01

    The feasibility of modeling a pressurized-water-reactor (PWR) facility and calculating dose rates at all locations within the containment and adjoining structures using MCNP5 with mesh tallies is presented. Calculations of dose rates resulting from neutron and photon sources from the reactor (operating and shut down for various periods) and the spent fuel pool, as well as for the photon source from the primary coolant loop, were all of interest. Identification of the PWR facility, development of the MCNP-based model and automation of the run process, calculation of the various sources, and development of methods for visually examining mesh tally files and extracting dose rates were all a significant part of the project. Advanced variance reduction, which was required because of the size of the model and the large amount of shielding, was performed via the CADIS/ADVANTG approach. This methodology uses an automatically generated three-dimensional discrete ordinates model to calculate adjoint fluxes from which MCNP weight windows and source bias parameters are generated. Investigative calculations were performed using a simple block model and a simplified full-scale model of the PWR containment, in which the adjoint source was placed in various regions. In general, it was shown that placement of the adjoint source on the periphery of the model provided adequate results for regions reasonably close to the source (e.g., within the containment structure for the reactor source). A modification to the CADIS/ADVANTG methodology was also studied in which a global adjoint source is weighted by the reciprocal of the dose response calculated by an earlier forward discrete ordinates calculation. This method showed improved results over those using the standard CADIS/ADVANTG approach, and its further investigation is recommended for future efforts.

  12. Secondary Startup Neutron Sources as a Source of Tritium in a Pressurized Water Reactor (PWR) Reactor Coolant System (RCS)

    SciTech Connect

    Shaver, Mark W.; Lanning, Donald D.

    2010-02-01

    The hypothesis of this paper is that the Zircaloy clad fuel source is minimal and that secondary startup neutron sources are the significant contributors of the tritium in the RCS that was previously assigned to release from fuel. Currently there are large uncertainties in the attribution of tritium in a Pressurized Water Reactor (PWR) Reactor Coolant System (RCS). The measured amount of tritium in the coolant cannot be separated out empirically into its individual sources. Therefore, to quantify individual contributors, all sources of tritium in the RCS of a PWR must be understood theoretically and verified by the sum of the individual components equaling the measured values.

  13. URSULA2 computer program. Volume 2. Applications (sensitivity studies and demonstration calculations). Final report. [PWR

    SciTech Connect

    Keeton, L.W.; Marchland, E.O.; Singhal, A.K.; Spalding, D.B.

    1980-01-01

    The URSULA2 computer program has been developed for the thermal-hydraulic analysis of steam generators for PWR nuclear power plants. It computes three-dimensional distributions of velocity, pressure, enthalpy, etc., in the shell of the generator, and the distributions of primary-fluid temperature within the tubes. The code is applicable to both steady and unsteady flows and is equiped with three physical models: the equal velocity homogeneous model, a slip (or two-fluid) model, and an algebraic slip model. Applications, sensitivity studies, and demonstration calculations are presented.

  14. THERMAL HISTORY OF CLADDING IN A 21 PWR WASTE PACKAGE LOADED WITH AVERAGE FUEL

    SciTech Connect

    H.M. Wade

    2000-01-25

    The purpose of this calculation is to evaluate a mid-assembly axial fuel cladding temperature profile of a 21 pressurized water reactor (PWR) spent nuclear fuel (SNF) waste package (WP) loaded with average fuel assemblies and emplaced in a monitored geologic repository. This calculation is intended to evaluate Viability Assessment (VA) and Enhanced Design Alternatives (EDA) II design configurations in support of performance assessment. This calculation was developed by Waste Package Operations (WPO) under Office of Civilian Radioactive Waste Management (OCRWM) procedure AP-3.12Q, Revision 0.

  15. Application of LBB to high energy piping systems in operating PWR

    SciTech Connect

    Swamy, S.A.; Bhowmick, D.C.

    1997-04-01

    The amendment to General Design Criterion 4 allows exclusion, from the design basis, of dynamic effects associated with high energy pipe rupture by application of leak-before-break (LBB) technology. This new approach has resulted in substantial financial savings to utilities when applied to the Pressurized Water Reactor (PWR) primary loop piping and auxiliary piping systems made of stainless steel material. To date majority of applications pertain to piping systems in operating plants. Various steps of evaluation associated with the LBB application to an operating plant are described in this paper.

  16. Development of emergency operator support system for next Japanese PWR plants

    SciTech Connect

    Ito, K.; Hanada, S.; Yoshida, Y.; Sugino, K.

    2006-07-01

    The purpose of main control room improvement is to reduce operator workload and potential human errors by offering a better working environment where operators can maximize their abilities. Japanese PWR utilities and Mitsubishi have developed an operator support system entitled Emergency Operator Support System (EOSS). The system supports operators in incidental/accidental situations which may be worsened by human errors. In order to confirm the validity of the system, a proto type was built, and was evaluated by operator crews. The consequence showed good result of effectiveness in avoiding potential human errors and decreasing workload of operators. (authors)

  17. SCALE 5.1 Predictions of PWR Spent Nuclear Fuel Isotopic Compositions

    SciTech Connect

    Radulescu, Georgeta; Gauld, Ian C; Ilas, Germina

    2010-03-01

    The purpose of this calculation report is to document the comparison to measurement of the isotopic concentrations for pressurized water reactor (PWR) spent nuclear fuel determined with the Standardized Computer Analysis for Licensing Evaluation (SCALE) 5.1 (Ref. ) epletion calculation method. Specifically, the depletion computer code and the cross-section library being evaluated are the twodimensional (2-D) transport and depletion module, TRITON/NEWT,2, 3 and the 44GROUPNDF5 (Ref. 4) cross-section library, respectively, in the SCALE .1 code system.

  18. Cavern/Vault Disposal Concepts and Thermal Calculations for Direct Disposal of 37-PWR Size DPCs

    SciTech Connect

    Hardin, Ernest; Hadgu, Teklu; Clayton, Daniel James

    2015-03-01

    This report provides two sets of calculations not presented in previous reports on the technical feasibility of spent nuclear fuel (SNF) disposal directly in dual-purpose canisters (DPCs): 1) thermal calculations for reference disposal concepts using larger 37-PWR size DPC-based waste packages, and 2) analysis and thermal calculations for underground vault-type storage and eventual disposal of DPCs. The reader is referred to the earlier reports (Hardin et al. 2011, 2012, 2013; Hardin and Voegele 2013) for contextual information on DPC direct disposal alternatives.

  19. Effects of Lower Drying-Storage Temperature on the Ductility of High-Burnup PWR Cladding

    SciTech Connect

    Billone, M. C.; Burtseva, T. A.

    2016-08-30

    The purpose of this research effort is to determine the effects of canister and/or cask drying and storage on radial hydride precipitation in, and potential embrittlement of, high-burnup (HBU) pressurized water reactor (PWR) cladding alloys during cooling for a range of peak drying-storage temperatures (PCT) and hoop stresses. Extensive precipitation of radial hydrides could lower the failure hoop stresses and strains, relative to limits established for as-irradiated cladding from discharged fuel rods stored in pools, at temperatures below the ductile-to-brittle transition temperature (DBTT).

  20. Experimental Investigation on the Effects of Coolant Concentration on Sub-Cooled Boiling and Crud Deposition on Reactor Cladding at Prototypical PWR Operating Conditions

    SciTech Connect

    Schultis, J., Kenneth; Fenton, Donald, L.

    2006-10-20

    Increasing demand for energy necessitates nuclear power units to increase power limits. This implies significant changes in the design of the core of the nuclear power units, therefore providing better performance and safety in operations. A major hindrance to the increase of nuclear reactor performance especially in Pressurized Deionized water Reactors (PWR) is Axial Offset Anomaly (AOA)--the unexpected change in the core axial power distribution during operation from the predicted distribution. This problem is thought to be occur because of precipitation and deposition of lithiated compounds like boric acid (H{sub 2}BO{sub 3}) and lithium metaborate (LiBO{sub 2}) on the fuel rod cladding. Deposited boron absorbs neutrons thereby affecting the total power distribution inside the reactor. AOA is thought to occur when there is sufficient build-up of crud deposits on the cladding during subcooled nucleate boiling. Predicting AOA is difficult as there is very little information regarding the heat and mass transfer during subcooled nucleate boiling. An experimental investigation was conducted to study the heat transfer characteristics during subcooled nucleate boiling at prototypical PWR conditions. Pool boiling tests were conducted with varying concentrations of lithium metaborate (LiBO{sub 2}) and boric acid (H{sub 2}BO{sub 3}) solutions in deionized water. The experimental data collected includes the effect of coolant concentration, subcooling, system pressure and heat flux on pool the boiling heat transfer coefficient. The analysis of particulate deposits formed on the fuel cladding surface during subcooled nucleate boiling was also performed. The results indicate that the pool boiling heat transfer coefficient degrades in the presence of boric acid and lithium metaborate compared to pure deionized water due to lesser nucleation. The pool boiling heat transfer coefficients decreased by about 24% for 5000 ppm concentrated boric acid solution and by 27% for 5000 ppm

  1. Feasibility study on nuclear core design for soluble boron free small modular reactor

    SciTech Connect

    Rabir, Mohamad Hairie Hah, Chang Joo; Ju, Cho Sung

    2015-04-29

    A feasibility study on nuclear core design of soluble boron free (SBF) core for small size (150MWth) small modular reactor (SMR) was investigated. The purpose of this study was to design a once through cycle SMR core, where it can be used to supply electricity to a remote isolated area. PWR fuel assembly design with 17×17 arrangement, with 264 fuel rods per assembly was adopted as the basis design. The computer code CASMO-3/MASTER was used for the search of SBF core and fuel assembly analysis for SMR design. A low critical boron concentration (CBC) below 200 ppm core with 4.7 years once through cycle length was achieved using 57 fuel assemblies having 170 cm of active height. Core reactivity controlled using mainly 512 number of 4 wt% and 960 12 wt% Gd rods.

  2. Use of Solid Hydride Fuel for Improved long-Life LWR Core Designs

    SciTech Connect

    Greenspan, E

    2006-04-30

    The primary objective of this project was to assess the feasibility of improving the performance of PWR and BWR cores by using solid hydride fuels instead of the commonly used oxide fuel. The primary measure of performance considered is the bus-bar cost of electricity (COE). Additional performance measures considered are safety, fuel bundle design simplicity – in particular for BWR’s, and plutonium incineration capability. It was found that hydride fuel can safely operate in PWR’s and BWR’s without restricting the linear heat generation rate of these reactors relative to that attainable with oxide fuel. A couple of promising applications of hydride fuel in PWR’s and BWR’s were identified: (1) Eliminating dedicated water moderator volumes in BWR cores thus enabling to significantly increase the cooled fuel rods surface area as well as the coolant flow cross section area in a given volume fuel bundle while significantly reducing the heterogeneity of BWR fuel bundles thus achieving flatter pin-by-pin power distribution. The net result is a possibility to significantly increase the core power density – on the order of 30% and, possibly, more, while greatly simplifying the fuel bundle design. Implementation of the above modifications is, though, not straightforward; it requires a design of completely different control system that could probably be implemented only in newly designed plants. It also requires increasing the coolant pressure drop across the core. (2) Recycling plutonium in PWR’s more effectively than is possible with oxide fuel by virtue of a couple of unique features of hydride fuel – reduced inventory of U-238 and increased inventory of hydrogen. As a result, the hydride fuelled core achieves nearly double the average discharge burnup and the fraction of the loaded Pu it incinerates in one pass is double that of the MOX fuel. The fissile fraction of the Pu in the discharged hydride fuel is only ~2/3 that of the MOX fuel and the

  3. Cartesian Meshing Impacts for PWR Assemblies in Multigroup Monte Carlo and Sn Transport

    NASA Astrophysics Data System (ADS)

    Manalo, K.; Chin, M.; Sjoden, G.

    2014-06-01

    Hybrid methods of neutron transport have increased greatly in use, for example, in applications of using both Monte Carlo and deterministic transport to calculate quantities of interest, such as flux and eigenvalue in a nuclear reactor. Many 3D parallel Sn codes apply a Cartesian mesh, and thus for nuclear reactors the representation of curved fuels (cylinder, sphere, etc.) are impacted in the representation of proper fuel inventory (both in deviation of mass and exact geometry representation). For a PWR assembly eigenvalue problem, we explore the errors associated with this Cartesian discrete mesh representation, and perform an analysis to calculate a slope parameter that relates the pcm to the percent areal/volumetric deviation (areal corresponds to 2D and volumetric to 3D, respectively). Our initial analysis demonstrates a linear relationship between pcm change and areal/volumetric deviation using Multigroup MCNP on a PWR assembly compared to a reference exact combinatorial MCNP geometry calculation. For the same multigroup problems, we also intend to characterize this linear relationship in discrete ordinates (3D PENTRAN) and discuss issues related to transport cross-comparison. In addition, we discuss auto-conversion techniques with our 3D Cartesian mesh generation tools to allow for full generation of MCNP5 inputs (Cartesian mesh and Multigroup XS) from a basis PENTRAN Sn model.

  4. Phenomenon analysis of stress corrosion cracking in the vessel head penetrations of French PWR`s

    SciTech Connect

    Pichon, C.; Buisine, D.; Faidy, C.; Gelpi, A.; Vaindirlis, M.

    1995-12-31

    During a hydrotest in 1991, a leak was detected on,a reactor vessel head (RVH) penetration of a French PWR. This leak was due to a phenomenon of Primary Water Stress Corrosion Cracking (PWSCC) affecting these penetrations in Alloy 600. The destructive and non-destructive examinations undertaken during the following months highlighted the generic nature of the degradations. In order to well understand this phenomenon and implement the most suitable maintenance policy, a large scale scientific program was decided and performed jointly by Electricite de France and FRAMATOME. The paper will present all the results obtained in this program concerning the parameters governing the PWSCC. In particular the following fields will be developed: (1) the material, its microstructure in line with the manufacturing and its susceptibility to PWSCC; (2) the stresses and their evaluations by measurements, mock up corrosion tests and Finite Element Analysis (FEA); (3) the effect of surface finish on crack initiation; and (4) the crack growth rate. This phenomenon analysis will be useful for evaluating the risk of PWSCC on other Alloy 600 areas in PWR`s primary system.

  5. Regeneratively Cooled Liquid Oxygen/Methane Technology Development Between NASA MSFC and PWR

    NASA Technical Reports Server (NTRS)

    Robinson, Joel W.; Greene, Christopher B.; Stout, Jeffrey B.

    2012-01-01

    The National Aeronautics & Space Administration (NASA) has identified Liquid Oxygen (LOX)/Liquid Methane (LCH4) as a potential propellant combination for future space vehicles based upon exploration studies. The technology is estimated to have higher performance and lower overall systems mass compared to existing hypergolic propulsion systems. NASA-Marshall Space Flight Center (MSFC) in concert with industry partner Pratt & Whitney Rocketdyne (PWR) utilized a Space Act Agreement to test an oxygen/methane engine system in the Summer of 2010. PWR provided a 5,500 lbf (24,465 N) LOX/LCH4 regenerative cycle engine to demonstrate advanced thrust chamber assembly hardware and to evaluate the performance characteristics of the system. The chamber designs offered alternatives to traditional regenerative engine designs with improvements in cost and/or performance. MSFC provided the test stand, consumables and test personnel. The hot fire testing explored the effective cooling of one of the thrust chamber designs along with determining the combustion efficiency with variations of pressure and mixture ratio. The paper will summarize the status of these efforts.

  6. Study of a transient identification system using a neural network for a PWR plant

    SciTech Connect

    Ishihara, Yoshinao; Kasai, Masao; Kambara, Masayuki; Mitsuda, Hiromichi; Kurata, Toshikazu; Shirosaki, Hidekazu

    1996-08-01

    This paper presents the procedure and results of a system for identifying PWR plant abnormal events, which uses neural network techniques. The neural network recognizes the abnormal event from the patterns of the transient changes of analog data from plant parameters when they deport from their normal state. For the identification of abnormal events in this study, events that cause a reactor to scram during power operation were selected as the design base events. The test data were prepared by simulating the transients on a compact PWR simulator. The simulation data were analyzed to determine how the plant parameters respond after the occurrence of a transient. A method of converting the pattern of the transient changes into characteristic parameters by fitting the data to pre-determined functions was developed. These characteristic parameters were used as the input data to the neural network. The neural network learning procedure used a generalized delta rule, namely a back-propagation algorithm. The neural network can identify the type of an abnormal event from a limited set of events by using these characteristic parameters obtained from the pattern of the changes in the analog data. From the results of this application of a neural network, it was concluded that it would be possible to use the method to identify abnormal events in a nuclear power plant.

  7. Application of the MELCOR code to design basis PWR large dry containment analysis.

    SciTech Connect

    Phillips, Jesse; Notafrancesco, Allen; Tills, Jack Lee

    2009-05-01

    The MELCOR computer code has been developed by Sandia National Laboratories under USNRC sponsorship to provide capability for independently auditing analyses submitted by reactor manufactures and utilities. MELCOR is a fully integrated code (encompassing the reactor coolant system and the containment building) that models the progression of postulated accidents in light water reactor power plants. To assess the adequacy of containment thermal-hydraulic modeling incorporated in the MELCOR code for application to PWR large dry containments, several selected demonstration designs were analyzed. This report documents MELCOR code demonstration calculations performed for postulated design basis accident (DBA) analysis (LOCA and MSLB) inside containment, which are compared to other code results. The key processes when analyzing the containment loads inside PWR large dry containments are (1) expansion and transport of high mass/energy releases, (2) heat and mass transfer to structural passive heat sinks, and (3) containment pressure reduction due to engineered safety features. A code-to-code benchmarking for DBA events showed that MELCOR predictions of maximum containment loads were equivalent to similar predictions using a qualified containment code known as CONTAIN. This equivalency was found to apply for both single- and multi-cell containment models.

  8. An extension of the validation of SCALE (SAS2H) isotopic predictions for PWR spent fuel

    SciTech Connect

    DeHart, M.D.; Hermann, O.W.

    1996-09-01

    Isotopic characterization of spent fuel via depletion and decay calculations is necessary for determination of source terms. Unlike fresh fuel assumptions typically used in criticality safety analysis of spent fuel configurations, burnup credit applications also rely on depletion and decay calculations to predict spent fuel composition; these isotopics are used in subsequent criticality calculations to assess the reduced worth of spent fuel. To validate the depletion codes and data, experiment is compared with predictions; such comparisons have been done in earlier ORNL work. This report describes additional independent measurements and corresponding calculations as a supplement. The current work includes measured isotopic data from 19 spent fuel samples from the Italian Trino Vercelles PWR and the US Turkey Point-3 PWR. In addition, an approach to determine biases and uncertainties between calculated and measured isotopic concentrations is discussed, together with a method to statistically combine these terms to obtain a conservative estimate of spent fuel isotopic concentrations. Results on combination of measured-to-calculated ratios are presented. The results described herein represent an extension to a new reactor design and spent fuel samples with enrichment as high as 3.9 wt% {sup 235}U. Consistency with the earlier work for each of two different cross-section libraries suggests that the estimated biases for each of the isotopes in the earlier work are reasonably good estimates.

  9. The Integral PWR SIR Transients: Comparisons Between CATHARE and RELAP Codes

    SciTech Connect

    Pignatel, Jean-Francois

    2002-07-01

    Within the framework of the research program on innovative light water reactors, the SERI (Service of Studies on Innovative Reactors) of the French Atomic Energy Commission (CEA), is presenting a predictive study on the modeling of a low-power integral Pressurized Water Reactor, using the CATHARE thermalhydraulic code. The concept selected for this study is that of the SIR reactor project, developed by AEA-T and ABB consortium. This very interesting concept is no doubt that which is the most complete to this date, and on which most information in the literature can be obtained. Many safety calculations made with the RELAP code are also available and represent a highly interesting base for comparison purposes, in order to improve the approach on the results obtained with CATHARE. A comparison of the behavior of the two codes is thus presented in this article. This study therefore shows that CATHARE finely models this type of new PWR concept. The transients studied cover a large area, ranging from natural circulation to loss of primary coolant accidents. The ATWS and a power transient have also been calculated. The comparison made between the CATHARE and RELAP results shows a very good agreement between the two codes, and leads to a very positive conclusion on the pertinence of simulating an integral PWR. Moreover, even though this study is a thorough investigation on the subject, it confirms the potentially safe nature of the SIR reactor. (author)

  10. Recommendations for Addressing Axial Burnup in the PWR Burnup Credit Analyses

    SciTech Connect

    Wagner, J.C.

    2002-10-23

    This report presents studies performed to support the development of a technically justifiable approach for addressing the axial-burnup distribution in pressurized-water reactor (PWR) burnup-credit criticality safety analyses. The effect of the axial-burnup distribution on reactivity and proposed approaches for addressing the axial-burnup distribution are briefly reviewed. A publicly available database of profiles is examined in detail to identify profiles that maximize the neutron multiplication factor, k{sub eff}, assess its adequacy for PWR burnup credit analyses, and investigate the existence of trends with fuel type and/or reactor operations. A statistical evaluation of the k{sub eff} values associated with the profiles in the axial-burnup-profile database was performed, and the most reactive (bounding) profiles were identified as statistical outliers. The impact of these bounding profiles on k{sub eff} is quantified for a high-density burnup credit cask. Analyses are also presented to quantify the potential reactivity consequence of loading assemblies with axial-burnup profiles that are not bounded by the database. The report concludes with a discussion on the issues for consideration and recommendations for addressing axial burnup in criticality safety analyses using burnup credit for dry cask storage and transportation.

  11. First Core and Refueling Options for IRIS

    SciTech Connect

    Petrovic, Bojan; Carelli, Mario D.; Greenspan, Ehud; Milosevic, Miodrag; Vujic, Jasmina; Padovani, Enrico; Ganda, Francesco

    2002-07-01

    The International Reactor Innovative and Secure (IRIS) is being developed by an international consortium of industry, laboratory, university and utility establishments, led by Westinghouse. The IRIS design addresses key requirements associated with advanced reactors, including improved safety, enhanced proliferation resistance, competitive electricity production cost, and improved waste management. IRIS is a modular, small/medium size (100 to 335 MWe) PWR with integral vessel configuration. Its design is based on proven LWR technology, so that no new technology development is needed and near term deployment is possible. At the same time, aim was to introduce improvements as compared to present PWRs. These opposing requirements resulted in an evolutionary approach to fuel and core design, balancing new features and the need to avoid extensive testing and demonstration programs. A path forward was devised by selecting the current fuel technology for the first IRIS core, but keeping future upgrades possible through the variable moderation fuel assembly design. This paper describes this approach and discusses core fueling options that enable achieving four-year and eight-year core lifetime. (authors)

  12. Simulation of the thermalhydraulic behavior of a molten core within a structure, with the three dimensions three components TOLBIAC code

    SciTech Connect

    Spindler, B.; Moreau, G.M.; Pigny S.

    1995-09-01

    The TOLBIAC code is devoted to the simulation of the behavior of a molten core within a structure (pressure vessel of core catcher), taking into account the relative position of the core components, the wall ablation and the crust formation. The code is briefly described: 3D model, physical properties and constitutive laws. wall ablation and crust model. Two results are presented: the simulation of the COPO experiment (natural convection with water in a 1/2 scale elliptic pressure vessel), and the simulation of the behavior of a corium in a PWR pressure vessel, with ablation and crust formation.

  13. Calculation of releases of radioactive materials in gaseous and liquid effluents from pressurized water reactors (PWR-GALE Code). Revision 1

    SciTech Connect

    Chandrasekaran, T.; Lee, J.Y.; Willis, C.A.

    1985-04-01

    This report revises the original issuance of NUREG-0017, ''Calculation of Releases of Radioactive Materials in Gaseous and Liquid Effluents from Pressurized Water Reactors (PWR-GALE-Code)'' (April 1976), to incorporate more recent operating data now available as well as the results of a number of in-plant measurement programs at operating pressurized water reactors. The PWR-GALE Code is a computerized mathematical model for calculating the releases of radioactive material in gaseous and liquid effluents (i.e., the gaseous and liquid source terms). The US Nuclear Regulatory Commission uses the PWR-GALE Code to determine conformance with the requirements of Appendix I to 10 CFR Part 50.

  14. PWR FLECHT SEASET 21-rod-bundle flow-blockage task: data and analysis report. NRC/EPRI/Westinghouse report No. 11, main report and appendices A-J

    SciTech Connect

    Loftus, M.J.; Hochreiter, L.E.; Lee, N.; McGuire, M.F.; Wenzel, A.H.; Valkovic, M.M.

    1982-09-01

    This report presents data and limited analysis from the 21-Rod Bundle Flow Blockage Task of the Full-Length Emergency Cooling Heat Transfer Separate Effects and Systems Effects Test Program (FLECHT SEASET). The tests consisted of forced and gravity reflooding tests utilizing electrical heater rods with a cosine axial power profile to simulate PWR nuclear core fuel rod arrays. Steam cooling and hydraulic characteristics tests were also conducted. These tests were utilized to determine effects of various flow blockage configurations (shapes and distributions) on reflooding behavior, to aid in development/assessment of computational models in predicting reflooding behavior of flow blockage configurations, and to screen flow blockage configurations for future 163-rod flow blockage bundle tests.

  15. Some Lessons Learned From the SIPACT Simulations on the Design of PWR and Improvement of AM Measures

    SciTech Connect

    Pochard, R.; Jedrzejewski, F.; Nilsuwankosit, S.

    2002-07-01

    the vessel was maintained and the safety margin time was increased. For the scenario that was related to a small break without HPIS, the concept of the safety time margin was still applicable. The time window was observed to be narrower for the bleeding on the secondary side if the core uncover was to be avoided, however. By observing the distribution of the mass in the primary loop, its behavior, which was directly related to the design, was fully demonstrated. One important finding showed that the current PWR design presented some disadvantage under the BDBA condition. Due to the way the water was accumulated in various components, sometime as much as that that was still remained in the pressure vessel, not all the water already presented or injected into the primary loop could reach the pressure vessel to be effectively utilized for core cooling. In order to characterize the availability of the water to cool the core, which related to the NPP BDBA robustness, a simple mass distribution criterion was proposed. Some improvements for the future design were also suggested. (authors)

  16. Heuristic rules embedded genetic algorithm for in-core fuel management optimization

    NASA Astrophysics Data System (ADS)

    Alim, Fatih

    The objective of this study was to develop a unique methodology and a practical tool for designing loading pattern (LP) and burnable poison (BP) pattern for a given Pressurized Water Reactor (PWR) core. Because of the large number of possible combinations for the fuel assembly (FA) loading in the core, the design of the core configuration is a complex optimization problem. It requires finding an optimal FA arrangement and BP placement in order to achieve maximum cycle length while satisfying the safety constraints. Genetic Algorithms (GA) have been already used to solve this problem for LP optimization for both PWR and Boiling Water Reactor (BWR). The GA, which is a stochastic method works with a group of solutions and uses random variables to make decisions. Based on the theories of evaluation, the GA involves natural selection and reproduction of the individuals in the population for the next generation. The GA works by creating an initial population, evaluating it, and then improving the population by using the evaluation operators. To solve this optimization problem, a LP optimization package, GARCO (Genetic Algorithm Reactor Code Optimization) code is developed in the framework of this thesis. This code is applicable for all types of PWR cores having different geometries and structures with an unlimited number of FA types in the inventory. To reach this goal, an innovative GA is developed by modifying the classical representation of the genotype. To obtain the best result in a shorter time, not only the representation is changed but also the algorithm is changed to use in-core fuel management heuristics rules. The improved GA code was tested to demonstrate and verify the advantages of the new enhancements. The developed methodology is explained in this thesis and preliminary results are shown for the VVER-1000 reactor hexagonal geometry core and the TMI-1 PWR. The improved GA code was tested to verify the advantages of new enhancements. The core physics code

  17. Application of MELCOR Code to a French PWR 900 MWe Severe Accident Sequence and Evaluation of Models Performance Focusing on In-Vessel Thermal Hydraulic Results

    SciTech Connect

    De Rosa, Felice

    2006-07-01

    In the ambit of the Severe Accident Network of Excellence Project (SARNET), funded by the European Union, 6. FISA (Fission Safety) Programme, one of the main tasks is the development and validation of the European Accident Source Term Evaluation Code (ASTEC Code). One of the reference codes used to compare ASTEC results, coming from experimental and Reactor Plant applications, is MELCOR. ENEA is a SARNET member and also an ASTEC and MELCOR user. During the first 18 months of this project, we performed a series of MELCOR and ASTEC calculations referring to a French PWR 900 MWe and to the accident sequence of 'Loss of Steam Generator (SG) Feedwater' (known as H2 sequence in the French classification). H2 is an accident sequence substantially equivalent to a Station Blackout scenario, like a TMLB accident, with the only difference that in H2 sequence the scram is forced to occur with a delay of 28 seconds. The main events during the accident sequence are a loss of normal and auxiliary SG feedwater (0 s), followed by a scram when the water level in SG is equal or less than 0.7 m (after 28 seconds). There is also a main coolant pumps trip when {delta}Tsat < 10 deg. C, a total opening of the three relief valves when Tric (core maximal outlet temperature) is above 603 K (330 deg. C) and accumulators isolation when primary pressure goes below 1.5 MPa (15 bar). Among many other points, it is worth noting that this was the first time that a MELCOR 1.8.5 input deck was available for a French PWR 900. The main ENEA effort in this period was devoted to prepare the MELCOR input deck using the code version v.1.8.5 (build QZ Oct 2000 with the latest patch 185003 Oct 2001). The input deck, completely new, was prepared taking into account structure, data and same conditions as those found inside ASTEC input decks. The main goal of the work presented in this paper is to put in evidence where and when MELCOR provides good enough results and why, in some cases mainly referring to its

  18. The OSMOSE program for the qualification of integral cross sections of actinides: Preliminary results in a PWR-UOx spectrum

    SciTech Connect

    Hudelot, J. P.; Antony, M.; Bernard, D.; Fougeras, P.

    2006-07-01

    -worth of the individual samples. The first experimental results were obtained with a very good reproducibility in 2005 and 2006 in the R1-UO{sub 2} core configuration representative of a PWR UOx standard spectrum. The preliminary results of measurements and comparison to calculational models are reported. (authors)

  19. 2-D pressurized water reactor whole core benchmark problem development and MOCUM program verification

    NASA Astrophysics Data System (ADS)

    Oredeko, Ayoola Emmanuel

    The need to solve larger-scale and highly heterogeneous reactor problems is urgent nowadays; different computational codes are being developed to meet this demand. Method of characteristics unstructured meshing (MOCUM) is a transport theory code based on the method of characteristic as the flux solver with an advanced general geometry processor. The objective of this research was to use the MOCUM program to solve the whole core, highly heterogeneous pressurized water reactor (PWR) benchmark problem, to determine its efficiency in solving complicated benchmarks, the large scale full-core PWR benchmark problem presented in this work was modeled for high heterogeneity at the core and assembly level, and depicts a realistic reactor design. The design of the core is a 15x15 assembly arrangement and each assembly is based on the C5G7 assembly design, i.e, 17x17 fuel pins. The problem was simplified for faster computation time by using the 1/4 symmetry of the core. MATLAB is used for the visualization of the neutron flux for each group, and the fission rate. MOCUM result shows good agreement with monte carlo N-particles (MCNP6) solution with a -0.025% difference in eigenvalue (keff). The pin and assembly power calculated with MOCUM, shows good agreement with that of MCNP6; the maximum relative difference for pin and assembly power was -2.53% and -1.79% respectively. The power profiles from these two computational codes were compared and used to validate the MOCUM solutions.

  20. In-Situ NDT Measurements of Irradiation Induced Swelling in PWR Core Internal Components - Phase 2: Testing of Irradiated Materials

    SciTech Connect

    I.Balachov, F.Garner, Y. Isobe

    2004-04-01

    OAK-B135 The objective of the project is to examine and develop in-situ nondestructive testing (NDT) techniques for measuring irradiation induced swelling in the internal components of PWRs. the two phases scope of the project covers development, validation, and application of NDT sensors capable of locating and measuring hidden volume expansion due to swelling at levels 0.1-0.5% or larger based on indirect material property variations such as Young's modulus changes. The first phase study published previously focused on evaluation NDT techniques using unirradiated surrogate materials. This report documents the second phase effort on benchmarking NDT techniques by testing irradiated materials.

  1. IMPACT OF FISSION PRODUCTS IMPURITY ON THE PLUTONIUM CONTENT IN PWR MOX FUELS

    SciTech Connect

    Gilles Youinou; Andrea Alfonsi

    2012-03-01

    This report presents the results of a neutronics analysis done in response to the charter IFCA-SAT-2 entitled 'Fuel impurity physics calculations'. This charter specifies that the separation of the fission products (FP) during the reprocessing of UOX spent nuclear fuel assemblies (UOX SNF) is not perfect and that, consequently, a certain amount of FP goes into the Pu stream used to fabricate PWR MOX fuel assemblies. Only non-gaseous FP have been considered (see the list of 176 isotopes considered in the calculations in Appendix 1). This mixture of Pu and FP is called PuFP. Note that, in this preliminary analysis, the FP losses are considered element-independent, i.e., for example, 1% of FP losses mean that 1% of all non-gaseous FP leak into the Pu stream.

  2. Effect of single aging on stress corrosion cracking susceptibility of INCONEL X-750 under PWR conditions

    NASA Astrophysics Data System (ADS)

    Mishra, B.; Moore, J. J.

    1988-05-01

    Unfavorable morphology of precipitates and inclusions has been thought to be the cause of severe intergranular stress corrosion cracking (IGSCC) in double aged INCONEL* X-750 alloy used in reactor water environments. A single step aging treatment of 200 hours at 811 °C followed by furnace cooling after solution treating for 2 hours at 1075 °C has been found to provide an improved combination of strength, ductility, and resistance to SCC under simulated PWR test conditions. In this single aged condition a reprecipitated secondary carbide, together with γ' was produced at the grain boundary which resulted in a mixed fracture mode comprising dimple rupture and microvoid coalescence compared with a predominantly intergranular mode for the fully age hardened specimens. This improvement has been explained in terms of the morphology of the second phase precipitates which are produced in these heat treatment regimes.

  3. Demonstration of Uncertainty Quantification and Sensitivity Analysis for PWR Fuel Performance with BISON

    SciTech Connect

    Zhang, Hongbin; Ladd, Jacob; Zhao, Haihua; Zou, Ling; Burns, Douglas

    2015-11-01

    BISON is an advanced fuels performance code being developed at Idaho National Laboratory and is the code of choice for fuels performance by the U.S. Department of Energy (DOE)’s Consortium for Advanced Simulation of Light Water Reactors (CASL) Program. An approach to uncertainty quantification and sensitivity analysis with BISON was developed and a new toolkit was created. A PWR fuel rod model was developed and simulated by BISON, and uncertainty quantification and sensitivity analysis were performed with eighteen uncertain input parameters. The maximum fuel temperature and gap conductance were selected as the figures of merit (FOM). Pearson, Spearman, and partial correlation coefficients were considered for all of the figures of merit in sensitivity analysis.

  4. A comparison of the CHF between tubes and annuli under PWR thermal-hydraulic conditions

    SciTech Connect

    Herer, C.

    1995-09-01

    Critical Heat Flux (CHF) tests were carried out in three tubes with inside diameters of 8, 13, and 19.2 mm and in two annuli with an inner tube of 9.5 mm and an outer tube of 13 or 19.2 mm. All axial heat flux distributions in the test sections were uniform. The coolant fluid was Refrigerant 12 (Freon-12) under PWR thermal-hydraulic conditions (equivalent water conditions - Pressure: 7 to 20 MPa, Mass Velocity: 1000 to 6000 kg/m2/s, Local Quality: -75% to +45%). The effect of tube diameter is correlated for qualities under 15%. The change from the tube to the annulus configuration is correctly taken into account by the equivalent hydraulic diameter. Useful information is also provided concerning the effect of a cold wall in an annulus.

  5. Methods and findings of a systems interaction study of a Westinghouse PWR

    SciTech Connect

    Youngblood, R.; Hanan, N.; Fitzpatrick, R.; Xue, D.; Bozoki, G.; Fresco, A.; Papazoglou, I.; Mitra, S.; Macdonald, G.; Chelliah, E.

    1985-01-01

    This paper describes the methods and findings of a systems interaction study of a Westinghouse PWR. BNL conducted the study as a methods application that was performed to support the resolution of Unresolved Safety Issue A-17 on Systems Interactions. The method calls for a fault tree model of the plant to be developed in stages, corresponding to successively increasing levels of scope and detail. A functional model is developed first, resolved only to sufficient detail to reflect support system dependences; this guides the subsequent searches for spatial and induced-human interactions. This process has led to the identification of an active single failure causing loss of low pressure injection following a large or medium LOCA.

  6. Grid-to-rod flow-induced impact study for PWR fuel in reactor

    SciTech Connect

    Jiang, Hao; Qu, Jun; Lu, Roger Y.; Wang, Jy-An John

    2016-06-10

    The source for grid-to-rod fretting in a pressurized water nuclear reactor (PWR) is the dynamic contact impact from hydraulic flow-induced fuel assembly vibration. In order to support grid-to-rod fretting wear mitigation research, finite element analysis (FEA) was used to evaluate the hydraulic flow-induced impact intensity between the fuel rods and the spacer grids. Three-dimensional FEA models, with detailed geometries of the dimple and spring of the actual spacer grids along with fuel rods, were developed for flow impact simulation. The grid-to-rod dynamic impact simulation provided insights of the contact phenomena at grid-rod interface. Finally, it is an essential and effective way to evaluate contact forces and provide guidance for simulative bench fretting-impact tests.

  7. Improvement of PWR liquid radwaste system in Korean Nuclear Power Plants

    SciTech Connect

    Lee, Byung-Sik; Kim, Kil-Jung; Ko, Dae-Hack

    1995-11-01

    Currently in Korea, there are 12 Pressurized Water Reactors (PWR) either operating or under construction. These units encompass several different designs for liquid radwaste systems. These different designs, however, may be categorized into three (3) basic groups based upon waste processing technologies. This paper describes the design concepts and operating experiences for the each. waste processing group. Based upon design and operating experiences, we implement to improve liquid radwaste system by simplification (i.e. elimination of unnecessary equipment) and employing current technologies. These improvements are applied to Yonggwang Unit 5&6, which is now in the basic design stage. This paper also describes some unique features of upgrading the liquid radwaste systems.

  8. Common cause evaluations in applied risk analysis of nuclear power plants. [PWR

    SciTech Connect

    Taniguchi, T.; Ligon, D.; Stamatelatos, M.

    1983-04-01

    Qualitative and quantitative approaches were developed for the evaluation of common cause failures (CCFs) in nuclear power plants and were applied to the analysis of the auxiliary feedwater systems of several pressurized water reactors (PWRs). Key CCF variables were identified through a survey of experts in the field and a review of failure experience in operating PWRs. These variables were classified into categories of high, medium, and low defense against a CCF. Based on the results, a checklist was developed for analyzing CCFs of systems. Several known techniques for quantifying CCFs were also reviewed. The information provided valuable insights in the development of a new model for estimating CCF probabilities, which is an extension of and improvement over the Beta Factor method. As applied to the analysis of the PWR auxiliary feedwater systems, the method yielded much more realistic values than the original Beta Factor method for a one-out-of-three system.

  9. Fog inerting effects on hydrogen combustion in a PWR ice condenser contaminant

    SciTech Connect

    Luangdilok, W.; Bennett, R.B.

    1995-05-01

    A mechanistic fog inerting model has been developed to account for the effects of fog on the upward lean flammability limits of a combustible mixture based on the thermal theory of flame propagation. Benchmarking of this model with test data shows reasonably good agreement between the theory and the experiment. Applications of the model and available fog data to determine the upward lean flammability limits of the H{sub 2}-air-steam mixture in the ice condenser upper plenum region of a pressurized water reactor (PWR) ice condenser contaminant during postulated large loss of coolant accident (LOCA) conditions indicate that combustion may be suppressed beyond the downward flammability limit (8 percent H{sub 2} by volume). 18 refs., 3 tabs.

  10. Grid-to-rod flow-induced impact study for PWR fuel in reactor

    DOE PAGES

    Jiang, Hao; Qu, Jun; Lu, Roger Y.; ...

    2016-06-10

    The source for grid-to-rod fretting in a pressurized water nuclear reactor (PWR) is the dynamic contact impact from hydraulic flow-induced fuel assembly vibration. In order to support grid-to-rod fretting wear mitigation research, finite element analysis (FEA) was used to evaluate the hydraulic flow-induced impact intensity between the fuel rods and the spacer grids. Three-dimensional FEA models, with detailed geometries of the dimple and spring of the actual spacer grids along with fuel rods, were developed for flow impact simulation. The grid-to-rod dynamic impact simulation provided insights of the contact phenomena at grid-rod interface. Finally, it is an essential and effectivemore » way to evaluate contact forces and provide guidance for simulative bench fretting-impact tests.« less

  11. The key to superior water chemistry at a PWR nuclear station

    SciTech Connect

    Dolan, R.; Miller, L.K.; Olejar, L.L.; Salem, E.

    1983-01-01

    This paper demonstrates how a condensate polishing unit can be successfully used to treat the feedwater for circulating-type pressurized water reactors (PWRs). Water chemistry at the Salem Generating Station, a two-unit, four-loop Westinghouse PWR located in New Jersey, is discussed. Topics considered include a plant description and the history of early operation, the role of constant surveillance, makeup water quality, the effect of freezing on gel-type anion exchange resin, a total organic carbon (TOC) survey, steam generator chemistry, steam generator inspection, condensate polisher operation, and management philosophy. The SEPREX condensate polishing process, in which the complete separation of the anion exchange resin from the cation exchange resin is achieved by flotation separation, is examined. It is concluded that the utilization of a condensate polishing process such as SEPREX provides the operating personnel at the plant with the necessary means to maintain the minimum desired level of contaminants within the steam generator.

  12. Development of cement solidification process for sodium borate waste generated from PWR plants

    SciTech Connect

    Hirofumi Okabe; Tatsuaki Sato; Yuichi Shoji; Yoshiko Haruguchi; Masaaki Kaneko; Michitaka Saso; Masumitsu Toyohara

    2013-07-01

    A cement solidification process for treating sodium borate waste produced in pressurized water reactor (PWR) plants was studied. To obtain high volume reduction and high mechanical strength of the waste, simulated concentrated borate liquid waste with a sodium / boron (Na/B) mole ratio of 0.27 was dehydrated and powdered by using a wiped film evaporator. To investigate the effect of the Na/B mole ratio on the solidification process, a sodium tetraborate decahydrate reagent with a Na/B mole ratio of 0.5 was also used. Ordinary portland cement (OPC) and some additives were used for the solidification. Solidified cement prepared from powdered waste with a Na/B mole ratio 0.24 and having a high silica sand content (silica sand/cement>2) showed to improved uniaxial compressive strength. (authors)

  13. A predictive model for corrosion fatigue crack growth rates in RPV steels exposed to PWR environments

    SciTech Connect

    Atkinson, J.D.; Chen, Z.; Yu, J.

    1995-12-31

    Corrosion fatigue crack propagation rates have been measured in A533B Class 1 plate in stagnant PWR primary water for a range of steel sulphur contents, temperature and corrosion potential values. Parametric descriptions of the data collected under constant rig conditions give good correlations for each variable and are consistent with a crack tip environment controlled process related to sulphur chemistry. A modified crack velocity equation is proposed to include temperature, sulphur content, polarization potential, frequency and {Delta}K values and it is shown how the predictions compare with the proposed ASME XI revision. Critical fatigue situations are identified for 0.003% and 0.019% sulphur steels typical of modern and old plant. The use of the equation in assessing the synergistic effect of variables is discussed.

  14. Three Dimensional Radiation Transport Analyses in Pwr with Tort and Mcnp

    NASA Astrophysics Data System (ADS)

    Fukuya, Koji; Nakata, Hayato; Kimura, Itsuro; Kitagawa, Hideo; Ohmura, Masaki; Ito, Taku; Shin, Kazuo

    2003-06-01

    Three dimensional (3D) neutron and gamma calculations for structural materials inside the reactor vessel in a commercial PWR were performed using the 3D transport code TORT and the Monte Carlo code MCNP to assess the accuracy of calculations using these codes and libraries. Comparisons with two dimensional DORT calculations with various libraries and surveillance dosimetry measurements indicated that TORT and MCNP calculations give similar agreements with surveillance measurements to DORT calculations. Influences of the cross section data, ENDF/B-IV, ENDF/B-VI and JENDL3.2 on attenuation of the fast flux and dpa rate in the reactor vessel, relative contributions of gamma-rays and thermal neutrons to dpa were discussed.

  15. Analysis of the NEACRP PWR rod ejection benchmark problems with DIF3D-K

    SciTech Connect

    Kim, M.H.; Taiwo, T.A.; Khalil, H.S.

    1994-03-01

    Analyses of the NEACRP PWR rod ejection transient benchmark problems with the DIF3D-K nodal kinetics code are presented. The DIF3D-K results are shown to be in generally good agreement with results obtained using other codes, in particular reference results previously generated with the PANTHER code. The sensitivity of the transient results to the DIF3D-K input parameters (such as time step size, radial and axial node sizes, and the mesh structure employed for fuel pin heat conduction calculation) are evaluated and discussed. In addition, the potential in reducing computational effort by application of the improved quasistatic scheme (IQS) to these rod ejection transients, which involve very significant flux shape changes and thermal-hydraulic feedback is evaluated.

  16. Assessment of non-backfittable concepts to improve PWR uranium utilization

    SciTech Connect

    LaBelle, D.W.; Sankovich, M.F.; Spetz, S.W.; Uotinen, V.O

    1980-12-01

    Seven non-backfittable improvements to light water reactors were assessed for Batelle/Pacific Northwest Laboratories in support of the Department of Energy's program on Advanced Reactor Studies. The objective was to provide industrial perspective as to which concepts have the best potential for development to improve fuel utilization. The concepts were rated against the assessment criteria while considering the key questions identified for each concept, and recommendations were made for further action on unresolved key questions. The concepts were subjectively ranked against each other in terms of relative investment potential. The ranking considered all criteria but, for example, weighted fuel utilization savings more heavily than development costs. Finally, conclusions and recommendations for future action were determined. The reference design for this study was the NASAP Composite Improved PWR.

  17. Grid-to-rod flow-induced impact study for PWR fuel in reactor

    SciTech Connect

    Jiang, Hao; Qu, Jun; Lu, Roger Y.; Wang, Jy-An John

    2016-06-10

    The source for grid-to-rod fretting in a pressurized water nuclear reactor (PWR) is the dynamic contact impact from hydraulic flow-induced fuel assembly vibration. In order to support grid-to-rod fretting wear mitigation research, finite element analysis (FEA) was used to evaluate the hydraulic flow-induced impact intensity between the fuel rods and the spacer grids. Three-dimensional FEA models, with detailed geometries of the dimple and spring of the actual spacer grids along with fuel rods, were developed for flow impact simulation. The grid-to-rod dynamic impact simulation provided insights of the contact phenomena at grid-rod interface. Finally, it is an essential and effective way to evaluate contact forces and provide guidance for simulative bench fretting-impact tests.

  18. PWR design for low doses in the United Kingdom: The present and the future

    SciTech Connect

    Zodiates, A.M.; Willcock, A.

    1995-03-01

    The Pressurizer Water Reactor (PWR) design chosen for adoption by Nuclear Electric plc was based on the Westinghouse Standard Nuclear Unit Power Plant System (SNUPPS). This design was developed to meet the United Kingdom (UK) requirements and those improvements are embodied in the Sizewell B plant. Nuclear Electric plc is now looking to the design of the future PWRs to be built in the UK. These PWRs will be based as replicas of the Sizewell B design, but attention will be given to reducing operator doses further. This paper details the approach in operator protection improvements incorporated at Sizewall B, presents the estimated annual collective dose, and identifies the approach being adopted to reduce further operator doses in future plants.

  19. Failure probability of PWR reactor coolant loop piping. [Double-ended guillotine break

    SciTech Connect

    Lo, T.; Woo, H.H.; Holman, G.S.; Chou, C.K.

    1984-02-01

    This paper describes the results of assessments performed on the PWR coolant loop piping of Westinghouse and Combustion Engineering plants. For direct double-ended guillotine break (DEGB), consideration was given to crack existence probability, initial crack size distribution, hydrostatic proof test, preservice inspection, leak detection probability, crack growth characteristics, and failure criteria based on the net section stress failure and tearing modulus stability concept. For indirect DEGB, fragilities of major component supports were estimated. The system level fragility was then calculated based on the Boolean expression involving these fragilities. Indirect DEGB due to seismic effects was calculated by convolving the system level fragility and the seismic hazard curve. The results indicate that the probability of occurrence of both direct and indirect DEGB is extremely small, thus, postulation of DEGB in design should be eliminated and replaced by more realistic criteria.

  20. Decontamination as a precursor to decommissioning. Status report Task 2: process evaluation. [PWR; BWR

    SciTech Connect

    Divine, J.R.; Woodruff, E.M.; McPartland, S.A.; Zima, G.E.

    1983-05-01

    As part of the US Nuclear Regulatory Commission's program to reduce occupational exposure and waste volumes, the Pacific Northwest Laboratory is studying decontamination as a precursor to decommissioning. Eleven processes or solvents were examined for their behavior in decontaminating BWR carbon steel samples. The solvents included NS-1, a proprietary solvent of Dow Chemical Corporation, designed for BWR use, and AP-Citrox, a well-known, two-step process designed for PWR stainless steel; it was used to provide a reference for later comparison to other systems and processes. The decontamination factors observed in the tests performed in a small laboratory scale recirculating loop ranged from about 1 (no effect) to 222 (about 99.6% of the initial activity removed. Coordinated corrosion measurements were made using twelve chemical solvents and eight metal alloys found in a range of reactor types.

  1. Monte Carlo characterization of PWR spent fuel assemblies to determine the detectability of pin diversion

    NASA Astrophysics Data System (ADS)

    Burdo, James S.

    This research is based on the concept that the diversion of nuclear fuel pins from Light Water Reactor (LWR) spent fuel assemblies is feasible by a careful comparison of spontaneous fission neutron and gamma levels in the guide tube locations of the fuel assemblies. The goal is to be able to determine whether some of the assembly fuel pins are either missing or have been replaced with dummy or fresh fuel pins. It is known that for typical commercial power spent fuel assemblies, the dominant spontaneous neutron emissions come from Cm-242 and Cm-244. Because of the shorter half-life of Cm-242 (0.45 yr) relative to that of Cm-244 (18.1 yr), Cm-244 is practically the only neutron source contributing to the neutron source term after the spent fuel assemblies are more than two years old. Initially, this research focused upon developing MCNP5 models of PWR fuel assemblies, modeling their depletion using the MONTEBURNS code, and by carrying out a preliminary depletion of a ¼ model 17x17 assembly from the TAKAHAMA-3 PWR. Later, the depletion and more accurate isotopic distribution in the pins at discharge was modeled using the TRITON depletion module of the SCALE computer code. Benchmarking comparisons were performed with the MONTEBURNS and TRITON results. Subsequently, the neutron flux in each of the guide tubes of the TAKAHAMA-3 PWR assembly at two years after discharge as calculated by the MCNP5 computer code was determined for various scenarios. Cases were considered for all spent fuel pins present and for replacement of a single pin at a position near the center of the assembly (10,9) and at the corner (17,1). Some scenarios were duplicated with a gamma flux calculation for high energies associated with Cm-244. For each case, the difference between the flux (neutron or gamma) for all spent fuel pins and with a pin removed or replaced is calculated for each guide tube. Different detection criteria were established. The first was whether the relative error of the

  2. Analysis of MERCI decay heat measurement for PWR UO{sub 2} fuel rod

    SciTech Connect

    Jaboulay, J.C.; Bourganel, S.

    2012-01-15

    Decay heat measurements, called the MERCI experiment, were conducted at Commissariat a l'Energie Atomique (CEA)/Saclay to characterize accurately residual power at short cooling time and verify its prediction by decay code and nuclear data. The MOSAIC calorimeter, developed and patented by CEA/Grenoble (DTN/SE2T), enables measurement of the decay heat released by a pressurized water reactor (PWR) fuel rod sample between 200 and 4 W within a precision of 1%. The MERCI experiment included three phases. At first, a UO{sub 2} fuel rod sample was irradiated in the CEA/Saclay experimental reactor OSIRIS. The burnup achieved at the end of irradiation was similar to 3.5 GWd/tonne. The second phase was the transfer of the fuel rod sample from its irradiation location to a hot cell, to be inserted inside the MOSAIC calorimeter. It took 26 min to carry out the transfer. Finally, decay heat released by the PWR sample was measured from 27 min to 42 days after shutdown. Post irradiation examinations were performed to measure concentrations of some heavy nuclei (U, Pu) and fission products (Cs, Nd). The decay heat was predicted using a calculation scheme based on the PEPIN2 depletion code, the TRIPOLI-4 Monte Carlo code, and the JEFF3.1.1 nuclear data file. The MERCI experiment analysis shows that the discrepancy between the calculated and the experimental decay heat values is included between -10% at 27 min and +6% at 12 h, 30 min otter shutdown. From 4 up to 42 days of cooling time, the difference between calculation and measurement is about ± 1%, i.e., experimental uncertainty. The MERCI experiment represents a significant contribution for code validation; the time range above 10{sup 5} s has not been validated previously. (authors)

  3. Irradiation Test of Advanced PWR Fuel in Fuel Test Loop at HANARO

    SciTech Connect

    Yang, Yong Sik; Bang, Je Geon; Kim, Sun Ki; Song, Kun Woo; Park, Su Ki; Seo, Chul Gyo

    2007-07-01

    A new fuel test loop has been constructed in the research reactor HANARO at KAERI. The main objective of the FTL (Fuel Test Loop) is an irradiation test of a newly developed LWR fuel under PWR or Candu simulated conditions. The first test rod will be loaded within 2007 and its irradiation test will be continued until a rod average their of 62 MWd/kgU. A total of five test rods can be loaded into the IPS (In-Pile Section) and fuel centerline temperature, rod internal pressure and fuel stack elongation can be measured by an on-line real time system. A newly developed advanced PWR fuel which consists of a HANA{sup TM} alloy cladding and a large grain UO{sub 2} pellet was selected as the first test fuel in the FTL. The fuel cladding, the HANA{sup TM} alloy, is an Nb containing Zirconium alloy that has shown better corrosion and creep resistance properties than the current Zircaloy-4 cladding. A total of six types of HANA{sup TM} alloy were developed and two or three of these candidate alloys will be used as test rod cladding, which have shown a superior performance to the others. A large-grain UO{sub 2} pellet has a 14{approx}16 micron 2D diameter grain size for a reduction of a fission gas release at a high burnup. In this paper, characteristics of the FTL and IPS are introduced and the expected operation and irradiation conditions are summarized for the test periods. Also the preliminary fuel performance analysis results, such as the cladding oxide thickness, fission gas release and rod internal pressure, are evaluated from the test rod safety analysis aspects. (authors)

  4. An Extension of the Validation of SCALE (SAS2H) Isotopic Predictions for PWR Spent Fuel

    SciTech Connect

    DeHart, M.D.

    1993-01-01

    Isotopic characterization of spent fuel via depletion and decay calculations is necessary for determination of source terms for subsequent system analyses involving heat transfer, radiation shielding, isotopic migration, etc. Unlike fresh fuel assumptions typically employed in the criticality safety analysis of spent fuel configurations, burnup credit applications also rely on depletion and decay calculations to predict the isotopic composition of spent fuel. These isotopics are used in subsequent criticality calculations to assess the reduced worth of spent fuel. To validate the codes and data used in depletion approaches, experimental measurements are compared with numerical predictions for relevant spent fuel samples. Such comparisons have been performed in earlier work at the Oak Ridge National Laboratory (ORNL). This report describes additional independent measurements and corresponding calculations, which supplement the results of the earlier work. The current work includes measured isotopic data from 19 spent fuel samples obtained from the Italian Trino Vercelles pressurized-water reactor (PWR) and the U.S. Turkey Point Unit 3 PWR. In addition, an approach to determine biases and uncertainties between calculated and measured isotopic concentrations is discussed, together with a method to statistically combine these terms to obtain a conservative estimate of spent fuel isotopic concentrations. Results are presented based on the combination of measured-to-calculated ratios for earlier work and the current analyses. The results described herein represent an extension to a new reactor design not included in the earlier work, and spent fuel samples with enrichment as high as 3.9 wt % {sup 235}U. Results for the current work are found to be, for the most part, consistent with the findings of the earlier work. This consistency was observed for results obtained from each of two different cross-section libraries and suggests that the estimated biases determined for

  5. Assessment of Reactivity Margins and Loading Curves for PWR Burnup Credit Cask Designs

    SciTech Connect

    Wagner, J.C.

    2002-12-17

    This report presents studies to assess reactivity margins and loading curves for pressurized water reactor (PWR) burnup-credit criticality safety evaluations. The studies are based on a generic high-density 32-assembly cask and systematically vary individual calculational (depletion and criticality) assumptions to demonstrate the impact on the predicted effective neutron multiplication factor, k{sub eff}, and burnup-credit loading curves. The purpose of this report is to provide a greater understanding of the importance of input parameter variations and quantify the impact of calculational assumptions on the outcome of a burnup-credit evaluation. This study should provide guidance to regulators and industry on the technical areas where improved information will most enhance the estimation of accurate subcritical margins. Based on these studies, areas where future work may provide the most benefit are identified. The report also includes an evaluation of the degree of burnup credit needed for high-density casks to transport the current spent nuclear fuel inventory. By comparing PWR discharge data to actinide-only based loading curves and determining the number of assemblies that meet the loading criteria, this evaluation finds that additional negative reactivity (through either increased credit for fuel burnup or cask design/utilization modifications) is necessary to accommodate the majority of current spent fuel assemblies in high-capacity casks. Assemblies that are not acceptable for loading in the prototypic high-capacity cask may be stored or transported by other means (e.g., lower capacity casks that utilize flux traps and/or increased fixed poison concentrations or high-capacity casks with design/utilization modifications).

  6. Analysis of proposed gamma-ray detection system for the monitoring of core water inventory in a pressurized water reactor

    SciTech Connect

    Markoff, D.M.

    1987-12-01

    An initial study has been performed of the feasibility of employing an axial array of gamma detectors located outside the pressure vessel to monitor the coolant in a PWR. A one-dimensional transport analysis model is developed for the LOFT research reactor and for a mock-PWR geometry. The gamma detector response to coolant voiding in the core and downcomer has been determined for both geometries. The effects of various conditions (for example, time after shutdown, materials in the transport path, and the relative void fraction in different water regions) on the detector response are studied. The calculational results have been validated by a favorable comparison with LOFT experimental data. Within the limitations and approximations considered in the analysis, the results indicate that the gamma-ray detection scheme is able to unambiguously respond to changes in the coolant inventory within any vessel water region.

  7. Nano-cavities observed in a 316SS PWR Flux Thimble Tube Irradiated to 33 and 70 dpa

    SciTech Connect

    Edwards, Danny J.; Garner, Francis A.; Bruemmer, Stephen M.; Efsing, Pal G.

    2009-02-28

    The radiation-induced microstructure of a cold-worked 316SS flux thimble tube from an operating pressurized water reactor (PWR) was examined. Two irradiated conditions, 33 dpa at 290ºC and 70 dpa at 315ºC were examined by transmission electron microscopy. The original dislocation network had completely disappeared and was replaced by fine dispersions of Frank loops and small nano-cavities at high densities. The latter appear to be bubbles containing high levels of helium and hydrogen. An enhanced distribution of these nano-cavities was found at grain boundaries and may play a role in the increased susceptibility of the irradiated 316SS to intergranular failure of specimens from this tube during post-irradiation slow strain rate testing in PWR water conditions.

  8. Results of small break LOCA experiments in the LOFT reactor system with comparison to code calculations. [PWR

    SciTech Connect

    Adams, J.P.; Linebarger, J.H.; Leach, L.P.

    1980-01-01

    The results are presented of three small break loss-of-coolant experiments performed in the LOFT Pressurized Water Reactor (PWR) system. Experiment L3-0, performed without reactor power, represented a loss of coolant from the power operated relief valve on the top of the pressurizer. Experiments L3-1 and L3-2 were initiated with the reactor at full power (maximum linear heat generation rate approximately 52 kW/m) and represented 4-in and 1-in diameter breaks, respectively, in the reactor inlet piping of a commercial PWR. Comparisons of data to analytical model calculations with a number of different models indicate that most major phenomena were correctly calculated, but that improvements in modeling small break behavior are necessary.

  9. SAS2H Generated Isotopic Concentrations For B&W 15X15 PWR Assembly (SCPB:N/A)

    SciTech Connect

    J.W. Davis

    1996-08-29

    This analysis is prepared by the Mined Geologic Disposal System (MGDS) Waste Package Development Department (WPDD) to provide pressurized water reactor (PWR) isotopic composition data as a function of time for use in criticality analyses. The objectives of this evaluation are to generate burnup and decay dependant isotopic inventories and to provide these inventories in a form which can easily be utilized in subsequent criticality calculations.

  10. Removal plan for Shippingport pressurized water reactor core 2 blanket fuel assemblies form T plant to the canister storage building

    SciTech Connect

    Lata

    1996-09-26

    This document presents the current strategy and path forward for removal of the Shippingport Pressurized Water Reactor Core 2 blanket fuel assemblies from their existing storage configuration (wet storage within the T Plant canyon) and transport to the Canister Storage Building (designed and managed by the Spent Nuclear Fuel. Division). The removal plan identifies all processes, equipment, facility interfaces, and documentation (safety, permitting, procedures, etc.) required to facilitate the PWR Core 2 assembly removal (from T Plant), transport (to the Canister storage Building), and storage to the Canister Storage Building. The plan also provides schedules, associated milestones, and cost estimates for all handling activities.

  11. 24. A CORE WORKER DISPLAYS THE CORE BOX AND CORES ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    24. A CORE WORKER DISPLAYS THE CORE BOX AND CORES FOR A BRASS GATE VALVE BODY MADE ON A CORE BOX, CA. 1950. - Stockham Pipe & Fittings Company, 4000 Tenth Avenue North, Birmingham, Jefferson County, AL

  12. Organ-specific gene expression in maize: The P-wr allele. Final report, August 15, 1993--August 14, 1996

    SciTech Connect

    Peterson, T.A.

    1997-06-01

    The ultimate aim of our work is to understand how a regulatory gene produces a specific pattern of gene expression during plant development. Our model is the P-wr gene of maize, which produces a distinctive pattern of pigmentation of maize floral organs. We are investigating this system using a combination of classical genetic and molecular approaches. Mechanisms of organ-specific gene expression are a subject of intense research interest, as it is the operation of these mechanisms during eukaryotic development which determine the characteristics of each organism Allele-specific expression has been characterized in only a few other plant genes. In maize, organ-specific pigmentation regulated by the R, B, and Pl genes is achieved by differential transcription of functionally conserved protein coding sequences. Our studies point to a strikingly different mechanism of organ-specific gene expression, involving post-transcriptional regulation of the regulatory P gene. The novel pigmentation pattern of the P-wr allele is associated with differences in the encoded protein. Furthermore, the P-wr gene itself is present as a unique tandemly amplified structure, which may affect its transcriptional regulation.

  13. Fuel-rod temperature transients during LWR degraded-core accidents

    SciTech Connect

    Briscoe, F; Rivard, J B; Young, M F

    1982-01-01

    Heat transfer models of fuel rods and coolant have been developed in support of LWR damaged fuel studies underway at Sandia National Laboratories for the NRC. A one-dimensional, full-length model simulates a PWR fuel rod; a two-dimensional, 0.5 m model simulates 9-rod bundle experiments to be performed in the Annular Core Research Reactor. The models include zircaloy oxidation, heat transfer by convecting steam/hydrogen flow, and radiation between surfaces through an absorbing/emitting gas. Characteristics of the one-dimensional reactor fuel rod model for two types of accident sequence are reported, as well as comparisons with MARCH code results.

  14. Core transfer

    NASA Astrophysics Data System (ADS)

    Good news for all petroleum geoscientists, mining and environmental scientists, university researchers, and the like: Shell Oil Company has deeded its Midland core and sample repository to the Bureau of Economic Geology (BEG) at the University of Texas at Austin. The Midland repository includes more than 1 million linear meters of slab, whole core, and prepared cuttings. Data comprising one of the largest U.S. core collections—the geologic samples from wells drilled in Texas and 39 other states—are now public data and will be incorporated into the existing BEG database. Both Shell and the University of Texas at Austin are affiliated with the American Geological Institute, which assisted in arranging the transfer as part of its goal to establish a National Geoscience Data Repository System at regional centers across the United States.

  15. Determination of uncertainties of PWR spent fuel radionuclide inventory based on real operational history data

    SciTech Connect

    Fast, Ivan; Bosbach, Dirk; Aksyutina, Yuliya; Tietze-Jaensch, Holger

    2015-07-01

    A requisite for the official approval of the safe final disposal of SNF is a comprehensive specification and declaration of the nuclear inventory in SNF by the waste supplier. In the verification process both the values of the radionuclide (RN) activities and their uncertainties are required. Burn-up (BU) calculations based on typical and generic reactor operational parameters do not encompass any possible uncertainties observed in real reactor operations. At the same time, the details of the irradiation history are often not well known, which complicates the assessment of declared RN inventories. Here, we have compiled a set of burnup calculations accounting for the operational history of 339 published or anonymized real PWR fuel assemblies (FA). These histories were used as a basis for a 'SRP analysis', to provide information about the range of the values of the associated secondary reactor parameters (SRP's). Hence, we can calculate the realistic variation or spectrum of RN inventories. SCALE 6.1 has been employed for the burn-up calculations. The results have been validated using experimental data from the online database - SFCOMPO-1 and -2. (authors)

  16. Brief account of the effect of overcooling accidents on the integrity of PWR pressure vessels

    SciTech Connect

    Cheverton, R.D.

    1982-01-01

    The occurrence in recent years of several (PWR) accident initiating events that could lead to severe thermal shock to the reactor pressure vessel, and the growing awareness that copper and nickel in the vessel material significantly enhance radiation damage in the vessel, have resulted in a reevaluation of pressure-vessel integrity during postulated overcooling accidents. Analyses indicate that the accidents of concern are those involving both thermal shock and pressure loadings, and that an accident similar to that at Rancho Seco in 1978 could, under some circumstances and at a time late in the normal life of the vessel, result in propagation of preexistent flaws in the vessel wall to the extent that they might completely penetrate the wall. More severe accidents have been postulated that would result in even shorter permissible lifetimes. However, the state-of-the-art fracture-mechanics analysis may contain excessive conservatism, and this possibility is being investigated. Furthermore, there are several remedial measures, such as fuel shuffling, to reduce the damage rate, and vessel annealing, to restore favorable material properties, that may be practical and used if necessary. 5 figures.

  17. Validation of the scale system for PWR spent fuel isotopic composition analyses

    SciTech Connect

    Hermann, O.W.; Bowman, S.M.; Parks, C.V.; Brady, M.C.

    1995-03-01

    The validity of the computation of pressurized-water-reactor (PWR) spent fuel isotopic composition by the SCALE system depletion analysis was assessed using data presented in the report. Radiochemical measurements and SCALE/SAS2H computations of depleted fuel isotopics were compared with 19 benchmark-problem samples from Calvert Cliffs Unit 1, H. B. Robinson Unit 2, and Obrigheim PWRs. Even though not exhaustive in scope, the validation included comparison of predicted and measured concentrations for 14 actinides and 37 fission and activation products. The basic method by which the SAS2H control module applies the neutron transport treatment and point-depletion methods of SCALE functional modules (XSDRNPM-S, NITAWL-II, BONAMI, and ORIGEN-S) is described in the report. Also, the reactor fuel design data, the operating histories, and the isotopic measurements for all cases are included in detail. The underlying radiochemical assays were conducted by the Materials Characterization. Center at Pacific Northwest Laboratory as part of the Approved Testing Material program and by four different laboratories in Europe on samples processed at the Karlsruhe Reprocessing Plant.

  18. Feasibility of recycling thorium in a fusion-fission hybrid/PWR symbiotic system

    SciTech Connect

    Josephs, J.M.

    1980-12-31

    A study was made of the economic impact of high levels of radioactivity in the thorium fuel cycle. The sources of this radioactivity and means of calculating the radioactive levels at various stages in the fuel cycle are discussed and estimates of expected levels are given. The feasibility of various methods of recycling thorium is discussed. These methods include direct recycle, recycle after storage for 14 years to allow radioactivity to decrease, shortening irradiation times to limit radioactivity build up, and the use of the window in time immediately after reprocessing where radioactivity levels are diminished. An economic comparison is made for the first two methods together with the throwaway option where thorium is not recycled using a mass energy flow model developed for a CTHR (Commercial Tokamak Hybrid Reactor), a fusion fission hybrid reactor which serves as fuel producer for several PWR reactors. The storage option is found to be most favorable; however, even this option represents a significant economic impact due to radioactivity of 0.074 mills/kW-h which amounts to $4 x 10/sup 9/ over a 30 year period assuming a 200 gigawatt supply of electrical power.

  19. Evaluation of on-line chelant addition to PWR steam generators. Steam generator cleaning project

    SciTech Connect

    Tvedt, T.J.; Wallace, S.L.; Griffin, F. Jr.

    1983-09-01

    The investigation of chelating agents for continuous water treatment of secondary loops of PWR steam generators were conducted in two general areas: the study of the chemistry of chelating agents and the study of materials compatability with chelating agents. The thermostability of both EDTA and HEDTA metal chelates in All Volatile Treatment (AVT) water chemistry were shown to be greater than or equal to the thermostability of EDTA metal chelates in phosphate-sulfite water chemistry. HEDTA metal chelates were shown to have a much greater stability than EDTA metal chelates. Using samples taken from the EDTA metal chelate thermostability study and from the Commonwealth Research Corporation (CRC) model steam generators (MSG), EDTA decomposition products were determined. Active metal surfaces were shown to become passivated when exposed to EDTA and HEDTA concentrations as high as 0.1% w/w in AVT. Trace amounts of iron in the water were found to increase the rate of passivation. Material balance and visual inspection data from CRC model steam generators showed that metal was transported through and cleaned from the MSG's. The Inconel 600 tubes of the salt water fouled model steam generators experienced pitting corrosion. Results of this study demonstrates the feasibility of EDTA as an on-line water treatment additive to maintain nuclear steam generators in a clean condition.

  20. Impact of makeup water system performance on PWR steam generator corrosion. Final report

    SciTech Connect

    Bell, M.J.; Pearl, W.L.; Sawochka, S.G.; Smith, L.A.

    1985-06-01

    The objectives of this project were to review makeup system design and performance and assess the possible relation of pressurized water reactor (PWR) steam generator corrosion to makeup water impurity ingress at fresh water sites. Project results indicated that makeup water transport of most ionic impurities can be expected to have a significant impact on secondary cycle chemistry only if condenser inleakage and other sources of impurities are maintained at very low levels. Since makeup water oxygen control techniques at most study plants were not consistent with state-of-the-art technology, oxygen input to the cycle via makeup can be significant. Leakage of colloidal silica and organics through makeup water systems can be expected to control blowdown silica levels and organic levels throughout the cycle at many plants. Attempts to correlate makeup water quality to steam generator corrosion observations were unsuccessful since (1) other impurity sources were significant compared to makeup at most study plants, (2) many variables are involved in the corrosion process, and (3) in the case of IGA, the variables have not been clearly established. However, in some situations makeup water can be a significant source of contaminants suspected to lead to both IGA and denting.

  1. Endurance tests of valves with cobalt-free hardfacing alloys: PWR phase

    SciTech Connect

    Murphy, E.V.; Inglis, I. )

    1992-05-01

    Atomic Energy of Canada Limited (AECL) is conducting endurance tests on valves hard-faced with four cobalt-free alloys. The first phase of the program, in which PWR primary heat transport conditions were simulated in AECL's valve test loop, has been completed. The candidate alloys are NOREM 01, NOREM 04, EB 5183 and EVERIT 50. One valve with Stellite 6 trim served as the standard. Prior to loop testing, a baseline inaugural inspection was performed. During testing the loop was shutdown at approximately 500 cycle intervals, and the valves were disassembled for examination. The examinations included seat leak tests, profilometry, nondestructive inspection and finally destructive examination. Corrosion coupons in the loop were used to monitor any material loss due solely to corrosion mechanisms. This report summarizes the final examination results and discusses the relative performance of the candidate alloys. The results indicate that, based upon the sliding wear damage assessment and seat leakage test results, all the candidate alloys perform better than the Stellite 6 control sample. On the same basis, NOREM 04 and EB 5183 are the best of the candidate alloys, although there are only minor differences in performance among the four alloys.

  2. Endurance tests of valves with cobalt-free hardfacing alloys: PWR phase. Final report

    SciTech Connect

    Murphy, E.V.; Inglis, I.

    1992-05-01

    Atomic Energy of Canada Limited (AECL) is conducting endurance tests on valves hard-faced with four cobalt-free alloys. The first phase of the program, in which PWR primary heat transport conditions were simulated in AECL`s valve test loop, has been completed. The candidate alloys are NOREM 01, NOREM 04, EB 5183 and EVERIT 50. One valve with Stellite 6 trim served as the standard. Prior to loop testing, a baseline inaugural inspection was performed. During testing the loop was shutdown at approximately 500 cycle intervals, and the valves were disassembled for examination. The examinations included seat leak tests, profilometry, nondestructive inspection and finally destructive examination. Corrosion coupons in the loop were used to monitor any material loss due solely to corrosion mechanisms. This report summarizes the final examination results and discusses the relative performance of the candidate alloys. The results indicate that, based upon the sliding wear damage assessment and seat leakage test results, all the candidate alloys perform better than the Stellite 6 control sample. On the same basis, NOREM 04 and EB 5183 are the best of the candidate alloys, although there are only minor differences in performance among the four alloys.

  3. Iodine partition coefficient measurements at simulated PWR steam generator conditions: Interim data report

    SciTech Connect

    Clinton, S.D.; Simmons, C.M.

    1987-05-01

    Iodine partition coefficients (defined as the ratio of the concentration of iodine species in the aqueous solution to the iodine concentration in the vapor phase) were measured at simulated PWR steam generator conditions (285C and 6.9 MPa), using carrier-free radioactive T I in the form of sodium iodide. The iodine tracer concentration was maintained at approx.6 x 10 mol/L; boric acid concentration was varied from 0 to 0.4 mol/L; and the solution pH (measured at 25C) was adjusted from 4 to 9 by the addition of lithium hydroxide. Iodine partition coefficients decrease with increasing boric acid concentration; however, the iodine volatility is essentially independent of the solution pH for a given boric acid concentration. Sparging the solutions with air at room temperature increases the iodine volatility by an order of magnitude, compared to that achieved with argon sparging. Iodine partition coefficient measurements ranged from a low of 200 (in 0.2 M boric acid sparged with air) to 400,000 (in purified water sparged with argon).

  4. Demonstration of optimum fuel-to-moderator ratio in a PWR unit fuel cell

    SciTech Connect

    Feltus, M.A.; Pozsgai, C. )

    1992-01-01

    Nuclear engineering students at The Pennsylvania State University develop scaled-down [[approx]350 MW(thermal)] pressurized water reactors (PWRs) using actual plants as references. The design criteria include maintaining the clad temperature below 2200[degree]F, fuel temperature below melting point, sufficient departure from nucleate boiling ratio (DNBR) margin, a beginning-of-life boron concentration that yields a negative moderator temperature coefficient, an adequate cycle power production (330 effective full-power days), and a batch loading scheme that is economical. The design project allows for many degrees of freedom (e.g., assembly number, pitch and height and batch enrichments) so that each student's result is unique. The iterative nature of the design process is stressed in the course. The LEOPARD code is used for the unit cell depletion, critical boron, and equilibrium xenon calculations. Radial two-group diffusion equations are solved with the TWIDDLE-DEE code. The steady-state ZEBRA thermal-hydraulics program is used for calculating DNBR. The unit fuel cell pin radius and pitch (fuel-to-moerator ratio) for the scaled-down design, however, was set equal to the already optimized ratio for the reference PWR. This paper describes an honors project that shows how the optimum fuel-to-moderator ratio is found for a unit fuel cell shown in terms of neutron economics. This exercise illustrates the impact of fuel-to-moderator variations on fuel utilization factor and the effect of assuming space and energy separability.

  5. Development of a coupling code for PWR reactor cavity radiation streaming calculation

    SciTech Connect

    Zheng, Z.; Wu, H.; Cao, L.; Zheng, Y.; Zhang, H.; Wang, M.

    2012-07-01

    PWR reactor cavity radiation streaming is important for the safe of the personnel and equipment, thus calculation has to be performed to evaluate the neutron flux distribution around the reactor. For this calculation, the deterministic codes have difficulties in fine geometrical modeling and need huge computer resource; and the Monte Carlo codes require very long sampling time to obtain results with acceptable precision. Therefore, a coupling method has been developed to eliminate the two problems mentioned above in each code. In this study, we develop a coupling code named DORT2MCNP to link the Sn code DORT and Monte Carlo code MCNP. DORT2MCNP is used to produce a combined surface source containing top, bottom and side surface simultaneously. Because SDEF card is unsuitable for the combined surface source, we modify the SOURCE subroutine of MCNP and compile MCNP for this application. Numerical results demonstrate the correctness of the coupling code DORT2MCNP and show reasonable agreement between the coupling method and the other two codes (DORT and MCNP). (authors)

  6. Key Issues for the control of refueling outage duration and costs in PWR Nuclear Power Plants

    SciTech Connect

    Degrave, Claude

    2002-07-01

    For several years, EDF, within the framework of the CIDEM1 project and in collaboration with some German Utilities, has undertaken a detailed review of the operating experience both of its own NPP and of foreign units, in order to improve the performances of future units under design, particularly the French-German European Pressurized Reactor (EPR) project. This review made it possible to identify the key issues allowing to decrease the duration of refueling and maintenance outages. These key issues can be classified in 3 categories Design, Maintenance and Logistic Support, Outage Management. Most of the key issues in the design field and some in the logistic support field have been studied and could be integrated into the design of any future PWR unit, as for the EPR project. Some of them could also be adapted to current plants, provided they are feasible and profitable. The organization must be tailored to each country, utility or period: it widely depends on the power production environment, particularly in a deregulation context. (author)

  7. LBB evaluation for a typical Japanese PWR primary loop by using the US NRC approved methods

    SciTech Connect

    Swamy, S.A.; Bhowmick, D.C.; Prager, D.E.

    1997-04-01

    The regulatory requirements for postulated pipe ruptures have changed significantly since the first nuclear plants were designed. The Leak-Before-Break (LBB) methodology is now accepted as a technically justifiable approach for eliminating postulation of double-ended guillotine breaks (DEGB) in high energy piping systems. The previous pipe rupture design requirements for nuclear power plant applications are responsible for all the numerous and massive pipe whip restraints and jet shields installed for each plant. This results in significant plant congestion, increased labor costs and radiation dosage for normal maintenance and inspection. Also the restraints increase the probability of interference between the piping and supporting structures during plant heatup, thereby potentially impacting overall plant reliability. The LBB approach to eliminate postulating ruptures in high energy piping systems is a significant improvement to former regulatory methodologies, and therefore, the LBB approach to design is gaining worldwide acceptance. However, the methods and criteria for LBB evaluation depend upon the policy of individual country and significant effort continues towards accomplishing uniformity on a global basis. In this paper the historical development of the U.S. LBB criteria will be traced and the results of an LBB evaluation for a typical Japanese PWR primary loop applying U.S. NRC approved methods will be presented. In addition, another approach using the Japanese LBB criteria will be shown and compared with the U.S. criteria. The comparison will be highlighted in this paper with detailed discussion.

  8. Experimental investigation on denting in PWR steam generators: causes and corrective actions

    SciTech Connect

    Nordmann, F.; Brunet, J.P.; Duret, J.; Pinard-Legry, G.

    1983-10-01

    Denting studies have been undertaken in order to assess the influence of the most important parameters which could initiate corrosion of the carbon steel occurring in the tube-tube support plate crevices of some PWR steam generators. Tests have been carried out in model boilers where feedwater was polluted with sea or river water. Specific effects of chloride or sulfate and influence of oxygen content, magnetite addition and pH value were investigated. In magnetite prepacked crevices, denting is obtained within 1000 hrs for seawater pollution of 0.3 ppm chloride at the blowdown. In neutral chloride or in river water, denting is observed only with oxygen addition. Denting prevention is effective in the case of an on-line addition of phosphate, boric acid, or calcium hydroxide. For denting stopping, boric acid or calcium hydroxide is efficient even with a high seawater pollution. Soaks cannot stop denting if they are not followed by an on-line treatment (boric acid, calcium hydroxide). With quadrifoil holes, denting doesn't occur. In very severe test conditions, 13 percent Cr steel can be corroded, but the corrosion rate is low and oxide morphology is different from that growing on carbon steel.

  9. Survey of the literature on low-alloy steel fastener corrosion in PWR power plants

    SciTech Connect

    Hall, J.F.

    1984-12-01

    This report presents the results of a literature survey of low alloy steel fastener corrosion in PWR applications. The report addresses boric acid corrosion (accelerated general corrosion) and stress corrosion cracking of threaded fasteners used in primary pressure boundary closures, in secondary, auxiliary, and safety system closures and in component support applications. The report reviews and summarizes corrosion events that have occurred in domestic PWRs since 1968. Information provided for each event includes plant identification, year of event, major component or part affected, fastener material, fastener diameter, number of corroded studs, the service environments, the number of degraded fasteners and the results of post-service failure analyses. Possible corrective actions that are available to eliminate or mitigate the effects of the two types of corrosion are also identified. Laboratory test data, including some recent unpublished data, that are related to fastener corrosion are also discussed. The report also includes recommended additional work in the areas of boric acid corrosion, stress corrosion cracking and analytical methodologies to solve these fastener corrosion problems.

  10. Compatibility of PWR gasket and packing materials and resins with organic amines

    SciTech Connect

    Keneshea, F.J.; Hobart, S.A. ); Camenzind, M.J. )

    1992-07-01

    The objectives of this testing program were two-fold: (1) to examine the compatibility of morpholine and five other amines with several synthetic polymeric materials useful for gaskets and seals in pressurized water reactor (PWR) secondary cycles and (2) to examine the potential chemical degradation of ion exchange (IX) resins by morpholine and ethanolamine. The screening of the polymeric materials in the amines was performed by heating small samples of the materials in the amines for one week to one month. Interaction of the amines with the materials was accelerated by testing at elevated temperatures and at high amine concentrations. Two materials (Kalrez and EPDM) that are potentially useful in high-temperature and high-pressure steam systems were tested in morpholine solutions in sealed bombs at 260{degrees}C (500{degrees}). After heating in the aqueous amine solutions, changes in weight were measured and the samples were visually examined for physical changes, such as swelling or cracking. Selected materials underwent testing for hardness, elongation, and tensile strength after heating in morpholine for one month. This document provides the results of this testing program.

  11. Aging mechanisms in the Westinghouse PWR (Pressurized Water Reactor) Control Rod Drive system

    SciTech Connect

    Gunther, W.; Sullivan, K.

    1991-01-01

    An aging assessment of the Westinghouse Pressurized Water Reactor (PWR) Control Rod System (CRD) has been completed as part of the US NRC's Nuclear Plant Aging Research, (NPAR) Program. This study examined the design, construction, maintenance, and operation of the system to determine its potential for degradation as the plant ages. Selected results from this study are presented in this paper. The operating experience data were evaluated to identify the predominant failure modes, causes, and effects. From our evaluation of the data, coupled with an assessment of the materials of construction and the operating environment, we conclude that the Westinghouse CRD system is subject to degradation which, if unchecked, could affect its safety function as a plant ages. Ways to detect and mitigate the effects of aging are included in this paper. The current maintenance for the control rod drive system at fifteen Westinghouse PWRs was obtained through a survey conducted in cooperation with EPRI and NUMARC. The results of the survey indicate that some plants have modified the system, replaced components, or expanded preventive maintenance. Several of these activities have effectively addressed the aging issue. 2 refs., 2 figs., 2 tabs.

  12. Remote Gamma Scanning System for Characterization of BWR and PWR Fuel Rod Sections

    SciTech Connect

    Crowell, Shannon L.; Alzheimer, James M.

    2011-08-08

    Sometimes challenges with the design and deployment of automated equipment in remote environments deals more with the constraints imposed by the remote environment than it does with the details of the automation. This paper discusses the development of a scanning system used to provide gamma radiation profiles of irradiated fuel rod segments. The system needed the capability to provide axial scans of cut segments of BWR and PWR fuel rods. The scanning location is A-Cell at the Radiochemical Processing Laboratory (RPL) at the Hanford site in Washington State. The criteria for the scanning equipment included axial scanning increments of a tenth of an inch or less, ability to scan fuel rods with diameters ranging from 3/8 inch to 5/8 inch in diameter, and fuel rod segments up to seven feet in length. Constraints imposed by the environment included having the gamma detector and operator controls on the outside of the hot cell and the scanning hardware on the inside of the hot cell. This entailed getting a narrow, collimated beam of radiation from the fuel rod to the detector on the outside of the hot cell while minimizing the radiation exposure caused by openings for the wires and cables traversing the hot cell walls. Setup and operation of all of the in-cell hardware needed to accommodate limited access ports and use of hot cell manipulators. The radiation levels inside the cell also imposed constraints on the materials used.

  13. Decay Heat Calculations for PWR and BWR Assemblies Fueled with Uranium and Plutonium Mixed Oxide Fuel using SCALE

    SciTech Connect

    Ade, Brian J; Gauld, Ian C

    2011-10-01

    in MOX fuel is generally obtained from reprocessed irradiated nuclear fuel, whereas weapons-grade plutonium is obtained from decommissioned nuclear weapons material and thus has a different plutonium (and other actinides) concentration. Using MOX fuel instead of UOX fuel has potential impacts on the neutronic performance of the nuclear fuel and the design of the nuclear fuel must take these differences into account. Each of the plutonium sources (RG and WG) has different implications on the neutronic behavior of the fuel because each contains a different blend of plutonium nuclides. The amount of heat and the number of neutrons produced from fission of plutonium nuclides is different from fission of {sup 235}U. These differences in UOX and MOX do not end at discharge of the fuel from the reactor core - the short- and long-term storage of MOX fuel may have different requirements than UOX fuel because of the different discharged fuel decay heat characteristics. The research documented in this report compares MOX and UOX fuel during storage and disposal of the fuel by comparing decay heat rates for typical pressurized water reactor (PWR) and boiling water reactor (BWR) fuel assemblies with and without weapons-grade (WG) and reactor-grade (RG) MOX fuel.

  14. Core layering

    NASA Astrophysics Data System (ADS)

    Jacobson, S. A.; Rubie, D. C.; Hernlund, J. W.; Morbidelli, A.

    2015-12-01

    We have created a planetary accretion and differentiation model that self-consistently builds and evolves Earth's core. From this model, we show that the core grows stably stratified as the result of rising metal-silicate equilibration temperatures and pressures, which increases the concentrations of light element impurities into each newer core addition. This stable stratification would naturally resist convection and frustrate the onset of a geodynamo, however, late giant impacts could mechanically mix the distinct accreted core layers creating large homogenous regions. Within these regions, a geodynamo may operate. From this model, we interpret the difference between the planetary magnetic fields of Earth and Venus as a difference in giant impact histories. Our planetary accretion model is a numerical N-body integration of the Grand Tack scenario [1]—the most successful terrestrial planet formation model to date [2,3]. Then, we take the accretion histories of Earth-like and Venus-like planets from this model and post-process the growth of each terrestrial planet according to a well-tested planetary differentiation model [4,5]. This model fits Earth's mantle by modifying the oxygen content of the pre-cursor planetesimals and embryos as well as the conditions of metal-silicate equilibration. Other non-volatile major, minor and trace elements included in the model are assumed to be in CI chondrite proportions. The results from this model across many simulated terrestrial planet growth histories are robust. If the kinetic energy delivered by larger impacts is neglected, the core of each planet grows with a strong stable stratification that would significantly impede convection. However, if giant impact mixing is very efficient or if the impact history delivers large impacts late, than the stable stratification can be removed. [1] Walsh et al. Nature 475 (2011) [2] O'Brien et al. Icarus 223 (2014) [3] Jacobson & Morbidelli PTRSA 372 (2014) [4] Rubie et al. EPSL 301

  15. Shippingport operations with the Light Water Breeder Reactor core. (LWBR Development Program)

    SciTech Connect

    Budd, W.A.

    1986-03-01

    This report describes the operation of the Shippingport Atomic Power Station during the LWBR (Light Water Breeder Reactor) Core lifetime. It also summarizes the plant-oriented operations during the period preceding LWBR startup, which include the defueling of The Pressurized Water Reactor Core 2 (PWR-2) and the installation of the LWBR Core, and the operations associated with the defueling of LWBR. The intent of this report is to examine LWBR experience in retrospect and present pertinent and significant aspects of LWBR operations that relate primarily to the nuclear portion of the Station. The nonnuclear portion of the Station is discussed only as it relates to overall plant operation or to unusual problems which result from the use of conventional equipment in radioactive environments. 30 refs., 69 figs., 27 tabs.

  16. The effect of stainless steel overlay cladding on corrosion fatigue crack propagation in pressure vessel steel in PWR primary coolant

    SciTech Connect

    Bramwell, I.L.; Tice, D.R.; Worswick, D.; Heys, G.B.

    1995-12-31

    The growth of sub-critical cracks in pressure boundary materials in light water reactors is assessed using codified procedures, but the presence of the overlay-welded stainless steel cladding on the pressure vessel is not normally taken into consideration because of the difficulty in demonstrating clad integrity for the lifetime of the plant. In order to investigate any possible effect of the cladding layer on crack propagation, tests have been performed using two types of specimen. The first was sputter ion plated with a thin layer of austenitic stainless steel to simulate the electrochemical and oxide effects due to the cladding, whilst the second used an overlay clad specimen to investigate the behavior of a crack propagating from the austenitic into the ferritic material. Testing was carried out under cyclic loading conditions in well controlled simulated PWR primary water. At 288 C, the presence of stainless steel in contact with the low alloy steel did not enhance crack propagation in PWR primary coolant compared to unclad or unplated specimens. There was limited evidence that at 288 C under certain loading conditions, in both air and PWR water, there may be an effect of the cladding which reduces crack growth rates, at least for a short distance of crack propagation into the low alloy steel. Crack growth rates in the ferritic steel at 130 C were higher for both the plated and clad specimens than found in previous tests under similar conditions on the unclad material. However, the crack growth rates were bounded by current ASME 11 Appendix A recommendations for defects exposed to water and at low R ratio. There was no evidence of environmental enhancement of crack propagation in the stainless steel in clad specimens. The results indicate that the current approach of ignoring the cladding for assessment purposes is conservative at plant operating temperature.

  17. ATHOS: a computer program for thermal-hydraulic analysis of steam generators. Volume 3. User's manual. [PWR

    SciTech Connect

    Singhal, A.K.; Keeton, L.W.; Przekwas, A.J.; Weems, J.S.

    1982-10-01

    ATHOS (Analysis of the Thermal Hydraulics of Steam Generators) is a computer code developed by CHAM of North America Incorporated, under the contract RP 1066-1 from the Electric Power Research Institute, Palo Alto, California. ATHOS supersedes the earlier code URSULA2. ATHOS is designed for three-dimensional, steady state and transient analyses of PWR steam generators. The current version of the code has been checked out for: three different configurations of the recirculating-type U-tube steam generators; the homogeneous and algebraic-slip flow models; and full and part load operating conditions.

  18. The Application of Modern Nodal Methods to Pwr Reactor Physics Analysis.

    NASA Astrophysics Data System (ADS)

    Knight, M. P.

    Available from UMI in association with The British Library. The objective of this research is to develop efficient computational procedures for PWR reactor calculations, based on modern nodal methods. The analytic nodal method, which is characterised by the use of exact exponential expansions in transverse-integrated equations, is implemented within an existing finite-difference code. This shows considerable accuracy and efficiency on standard benchmark problems, very much in line with existing experience with nodal methods. Assembly powers can be calculated to within 2.0% with just one mesh per assembly. The recovery of fine detail from a nodal solution based on such a coarse mesh requires additional effort. Techniques are develolped in this thesis which allow the basic nodal equations to be used in this reconstruction, and therefore provide a consistent approach. Pin powers can be recovered from assembly-averaged values with little further loss of accuracy. A similar investigation is followed with the transverse leakage distribution. An improvement, which uses known local behaviour, is shown to be very effective in some limited applications, but overall provides little advantage over the much simpler quadratic model. For heterogeneous calculations it is essential that the homogenisation techniques are well matched to the nodal method. The asymmetric design of some assemblies provides a severe test. Techniques are devised that allow some overall representation of this asymmetry to be retained in the reactor calculation, even when using one mesh per assembly. Extensions of this procedure provide an almost exact global representation of a heterogeneous assembly. A complete comparison is performed between reactor calculations at one mesh per pin, and at one mesh per assembly using nodal and homogenisation methods. Homogenisation errors and nodal coarse-mesh errors are shown to be very similar, amounting to about 0.1% on reactor eigenvalue, 2.0% on assembly power and

  19. A safety and regulatory assessment of generic BWR and PWR permanently shutdown nuclear power plants

    SciTech Connect

    Travis, R.J.; Davis, R.E.; Grove, E.J.; Azarm, M.A.

    1997-08-01

    The long-term availability of less expensive power and the increasing plant modification and maintenance costs have caused some utilities to re-examine the economics of nuclear power. As a result, several utilities have opted to permanently shutdown their plants. Each licensee of these permanently shutdown (PSD) plants has submitted plant-specific exemption requests for those regulations that they believe are no longer applicable to their facility. This report presents a regulatory assessment for generic BWR and PWR plants that have permanently ceased operation in support of NRC rulemaking activities in this area. After the reactor vessel is defueled, the traditional accident sequences that dominate the operating plant risk are no longer applicable. The remaining source of public risk is associated with the accidents that involve the spent fuel. Previous studies have indicated that complete spent fuel pool drainage is an accident of potential concern. Certain combinations of spent fuel storage configurations and decay times, could cause freshly discharged fuel assemblies to self heat to a temperature where the self sustained oxidation of the zircaloy fuel cladding may cause cladding failure. This study has defined four spent fuel configurations which encompass all of the anticipated spent fuel characteristics and storage modes following permanent shutdown. A representative accident sequence was chosen for each configuration. Consequence analyses were performed using these sequences to estimate onsite and boundary doses, population doses and economic costs. A list of candidate regulations was identified from a screening of 10 CFR Parts 0 to 199. The continued applicability of each regulation was assessed within the context of each spent fuel storage configuration and the results of the consequence analyses.

  20. Development of the ACP safeguards neutron counter for PWR spent fuel rods

    NASA Astrophysics Data System (ADS)

    Lee, Tae-Hoon; Menlove, Howard O.; Lee, Sang-Yoon; Kim, Ho-Dong

    2008-04-01

    An advanced neutron multiplicity counter has been developed for measuring spent fuel in the Advanced spent fuel Conditioning Process (ACP) at the Korea Atomic Energy Research Institute (KAERI). The counter uses passive neutron multiplicity counting to measure the 244Cm content in spent fuel. The input to the ACP process is spent fuel from pressurized water reactors (PWRs), and the high intensity of the gamma-ray exposure from spent fuel requires a careful design of the counter to measure the neutrons without gamma-ray interference. The nuclear safeguards for the ACP facility requires the measurement of the spent fuel input to the process and the Cm/Pu ratio for the plutonium mass accounting. This paper describes the first neutron counter that has been used to measure the neutron multiplicity distribution from spent fuel rods. Using multiple samples of PWR spent fuel rod-cuts, the singles (S), doubles (D), and triples (T) rates of the neutron distribution for the 244Cm nuclide were measured and calibration curves were produced. MCNPX code simulations were also performed to obtain the three counting rates and to compare them with the measurement results. The neutron source term was evaluated by using the ORIGEN-ARP code. The results showed systematic difference of 21-24% in the calibration graphs between the measured and simulation results. A possible source of the difference is that the burnup codes have a 244Cm uncertainty greater than ±15% and it would be systematic for all of the calibration samples. The S/D and D/T ratios are almost constant with an increment of the 244Cm mass, and this indicates that the bias is in the 244Cm neutron source calculation using the ORIGEN-ARP source code. The graphs of S/D and D/T ratios show excellent agreement between measurement and MCNPX simulation results.

  1. On-line PWR RHR pump performance testing following motor and impeller replacement

    SciTech Connect

    DiMarzo, J.T.

    1996-12-01

    On-line maintenance and replacement of safety-related pumps requires the performance of an inservice test to determine and confirm the operational readiness of the pumps. In 1995, major maintenance was performed on two Pressurized Water Reactor (PWR) Residual Heat Removal (RHR) Pumps. A refurbished spare motor was overhauled with a new mechanical seal, new motor bearings and equipped with pump`s `B` impeller. The spare was installed into the `B` train. The motor had never been run in the system before. A pump performance test was developed to verify it`s operational readiness and determine the in-situ pump performance curve. Since the unit was operating, emphasis was placed on conducting a highly accurate pump performance test that would ensure that it satisfied the NSSS vendors accident analysis minimum acceptance curve. The design of the RHR System allowed testing of one train while the other was aligned for normal operation. A test flow path was established from the Refueling Water Storage Tank (RWST) through the pump (under test) and back to the RWST. This allowed staff to conduct a full flow range pump performance test. Each train was analyzed and an expression developed that included an error vector term for the TDH (ft), pressure (psig), and flow rate (gpm) using the variance error vector methodology. This method allowed the engineers to select a test instrumentation system that would yield accurate readings and minimal measurement errors, for data taken in the measurement of TDH (P,Q) versus Pump Flow Rate (Q). Test results for the `B` Train showed performance well in excess of the minimum required. The motor that was originally in the `B` train was similarly overhauled and equipped with `A` pump`s original impeller, re-installed in the `A` train, and tested. Analysis of the `A` train results indicate that the RHR pump`s performance was also well in excess of the vendors requirements.

  2. Impact of Pin-by-Pin Thermal-Hydraulic Feedback Modeling on Steady-State Core Characteristics

    SciTech Connect

    Yamamoto, Akio; Ikeno, Tsutomu

    2005-02-15

    In this paper, the effect of a pin-by-pin thermal-hydraulic feedback treatment on the core characteristics at a steady-state condition is investigated using a three-dimensional fine-mesh core calculation code. Currently, advanced nodal codes treat the inside of an assembly as homogeneous, and the temperature distribution inside a node is usually ignored. Namely, the fuel temperature is estimated from the assembly average power density, and the moderator temperature is calculated from the nodewise closed-channel model. However, the validity of a flat temperature distribution inside a node has not yet been investigated, because a three-dimensional pin-by-pin whole-core calculation must be done for comparison. A three-dimensional pin-by-pin nodal-transport code for a pressurized water reactor (PWR) core analysis, SCOPE2, was used in this study since it can directly treat the pin-by-pin feedback effect. A whole-core subchannel analysis code was developed to enhance the thermal-hydraulic capability of SCOPE2. The pin-by-pin feedback models for fuel and moderator temperature were established, and their impact on the core characteristics was investigated in a 3 x 3 multiassembly and the whole PWR core geometries. The calculations showed that modeling of the pin-by-pin temperature distribution revealed a negligible effect on core reactivity and only a slight impact on the radial peaking factor. The difference in the radial peaking factor that is exposed by the pin-by-pin temperature modeling is less than 0.005 in the test calculations.

  3. Investigation of the Effect of Fixed Absorbers on the Reactivity of PWR Spent Nuclear Fuel for Burnup Credit

    SciTech Connect

    Wagner, John C.; Sanders, Charlotta E.

    2002-08-15

    The effect of fixed absorbers on the reactivity of pressurized water reactor (PWR) spent nuclear fuel (SNF) in support of burnup-credit criticality safety analyses is examined. A fuel assembly burned in conjunction with fixed absorbers may have a higher reactivity for a given burnup than an assembly that has not used fixed absorbers. As a result, guidance on burnup credit, issued by the U.S. Nuclear Regulatory Commission's Spent Fuel Project Office, recommends restricting the use of burnup credit to assemblies that have not used burnable absorbers. This recommendation eliminates a large portion of the currently discharged SNF from loading in burnup credit casks and thus severely limits the practical usefulness of burnup credit. Therefore, data are needed to support the extension of burnup credit to additional SNF. This research investigates the effect of various fixed absorbers, including integral burnable absorbers, burnable poison rods, control rods, and axial power shaping rods, on the reactivity of PWR SNF. Trends in reactivity with relevant parameters (e.g., initial fuel enrichment, burnup and absorber type, exposure, and design) are established, and anticipated reactivity effects are quantified. Where appropriate, recommendations are offered for addressing the reactivity effects of the fixed absorbers in burnup-credit safety analyses.

  4. COMMIX-1A analysis of fluid and thermal mixing in a model cold leg and downcomer of a PWR

    SciTech Connect

    Chen, B.C.J.; Cha, B.K.; Miao, C.C.; Sha, W.T.; Kim, J.H.; Sun, B.K.H.

    1983-01-01

    The issue of thermal shock of a PWR pressure vessel has been under considerable attention recently. A number of experimental as well as analytical studies have been performed to investigate the effect of the thermal transient on the pressure vessel due to the high pressure injection (HPI) of the cold fluid into the cold leg. This process has been called Pressurized Thermal Shock (PTS). This paper is an analytical study of PTS by using COMMIX-1A. Experimental investigations were performed at CREARE and SAI. In the CREARE experiment, a 1/5 scale model was set up to simulate a cold leg and downcomer of a PWR. Tests with several different ratios of hot loop flow versus cold HPI flow were performed to study the effect of the flow ratio on the fluid and thermal mixing process in the system, especially in the downcomer region. Analytical investigations also proceeded in parallel with the experiments. Quite a few analytical investigations were performed with the COMMIX-1A code. However, in this version of COMMIX, the effect of the numerical diffusion was not addressed.

  5. Testing and analyses of the TN-24P PWR spent-fuel dry storage cask loaded with consolidated fuel

    SciTech Connect

    McKinnon, M A; Michener, T E; Jensen, M F; Rodman, G R

    1989-02-01

    A performance test of a Transnuclear, Inc. TN-24P storage cask configured for pressurized water reactor (PWR) spent fuel was performed. The work was performed by the Pacific Northwest Laboratory (PNL) and Idaho National Engineering Laboratory (INEL) for the US Department of Energy Office of Civilian Radioactive Waste Management (OCRWM) and the Electric Power Research Institute. The performance test consisted of loading the TN-24P cask with 24 canisters of consolidated PWR spent fuel from Virginia Power's Surry and Florida Power and Light's Turkey Point reactors. Cask surface and fuel canister guide tube temperatures were measured, as were cask surface gamma and neutron dose rates. Testing was performed with vacuum, nitrogen, and helium backfill environments in both vertical and horizontal cask orientations. Transnuclear, Inc., arranged to have a partially insulated run added to the end of the test to simulate impact limiters. Limited spent fuel integrity data were also obtained. From both heat transfer and shielding perspectives, the TN-24P cask with minor refinements can be effectively implemented at reactor sites and central storage facilities for safe storage of unconsolidated and consolidated spent fuel. 35 refs., 93 figs., 17 tabs.

  6. Parametric study of CHF data. Volume 2. A generalized subchannel CHF correlation for PWR and BWR fuel assemblies. Final report

    SciTech Connect

    Reddy, D.G.; Fighetti, C.F.

    1983-01-01

    The primary objective of this research was to develop a generalized subchannel CHF correlation based on the local fluid conditions obtained with the COBRA-IIIC thermal hydraulic subchannel code and covering PWR and BWR normal operating conditions as well as hypothetical loss-of-coolant accident (LOCA) conditions. In view of the importance of the local conditions predicted by the COBRA-IIIC code in the development of CHR correlation, the secondary objective was to improve the predictive capability of the COBRA-IIIC subchannel code. In the first phase of this study, the sensitivity of local enthalpies and local mass fluxes predicted by the COBRA-IIIC subchannel code to subcooled void correlation, bulk void correlation, two-phase friction multiplier correlation and turbulent mixing parameter was determined. In the second phase, based on the local conditions obtained with the COBRA-IIIC subchannel code, an accurate generalized subchannel CHF correlation was developed utilizing 3607 CHF data points from 65 test sections simulating PWR and BWR fuel assemblies.

  7. Asymmetric blowdown loads on PWR (pressurized-water-reactor) primary systems: resolution of generic task action plan A-2

    SciTech Connect

    Hosford, S.B.; Mattu, R.; Meyer, R.O.; Throm, E.D.; Tinkler, C.G.

    1981-01-01

    NRC staff, after being informed of newly identified asymmetric loadings resulting from postulated ruptures of primary piping, initiated a generic investigation, Task Action Plan A-2, limited to pressurized-water-reactor (PWR) plants because of their higher primary system pressures. The intent of the investigation was to develop acceptable criteria and guidelines for evaluating plant analyses. The staff concludes that an acceptable basis is provided in this report for performing and reviewing plant analyses. Criteria were developed for evaluating loading transients, structural components, and the fuel assembly. The staff approved computer programs and modeling techniques submitted by each PWR vendor for development of the subcooled blowdown and cavity-pressure loading transients. Audit models were developed to evaluate the structural computer programs and modeling techniques. Methods have been approved for the structural-analysis method submitted by Westinghouse for the Indian Point Unit 3 plant. Criteria and guidelines are provided to perform a detailed evaluation of the fuel assembly. Acceptance criteria are also provided so deformed fuel-assembly spacer grids may be evaluated.

  8. Analytical Transmission Electron Microscopy Characterization of Stress Corrosion Cracks in an Irradiated Type 316 Stainless Steel Core Component

    SciTech Connect

    Thomas, Larry E.; Bruemmer, Stephen M.

    2002-05-31

    Irradiation-assisted stress-corrosion cracking (IASCC) of a cold-worked type 316 stainless steel baffle/former bolt from a pressurized-water reactor (PWR) was investigated by analytical transmission electron microscopy (ATEM). Nanometer-resolution methods for feature-specific analysis were used to characterize irradiation and corrosion-affected microstructures of the crack tip. The work is part of an international cooperative program to characterize light-water-reactor core components that experience IASCC. This is the first detailed ATEM examination of in-service cracks in neutron-irradiated austenitic stainless steel.

  9. ALARA Analysis for Shippingport Pressurized Water Reactor Core 2 Fuel Storage in the Canister Storage Building (CSB)

    SciTech Connect

    LEWIS, M.E.

    2000-04-06

    The addition of Shippingport Pressurized Water Reactor (PWR) Core 2 Blanket Fuel Assembly storage in the Canister Storage Building (CSB) will increase the total cumulative CSB personnel exposure from receipt and handling activities. The loaded Shippingport Spent Fuel Canisters (SSFCs) used for the Shippingport fuel have a higher external dose rate. Assuming an MCO handling rate of 170 per year (K East and K West concurrent operation), 24-hr CSB operation, and nominal SSFC loading, all work crew personnel will have a cumulative annual exposure of less than the 1,000 mrem limit.

  10. The effects of cold rolling orientation and water chemistry on stress corrosion cracking behavior of 316L stainless steel in simulated PWR water environments

    NASA Astrophysics Data System (ADS)

    Chen, Junjie; Lu, Zhanpeng; Xiao, Qian; Ru, Xiangkun; Han, Guangdong; Chen, Zhen; Zhou, Bangxin; Shoji, Tetsuo

    2016-04-01

    Stress corrosion cracking behaviors of one-directionally cold rolled 316L stainless steel specimens in T-L and L-T orientations were investigated in hydrogenated and deaerated PWR primary water environments at 310 °C. Transgranular cracking was observed during the in situ pre-cracking procedure and the crack growth rate was almost not affected by the specimen orientation. Locally intergranular stress corrosion cracks were found on the fracture surfaces of specimens in the hydrogenated PWR water. Extensive intergranular stress corrosion cracks were found on the fracture surfaces of specimens in deaerated PWR water. More extensive cracks were found in specimen T-L orientation with a higher crack growth rate than that in the specimen L-T orientation with a lower crack growth rate. Crack branching phenomenon found in specimen L-T orientation in deaerated PWR water was synergistically affected by the applied stress direction as well as the preferential oxidation path along the elongated grain boundaries, and the latter was dominant.

  11. High mechanical performance of Areva upgraded fuel assemblies for PWR in USA

    SciTech Connect

    Gottuso, Dennis; Canat, Jean-Noel; Mollard, Pierre

    2007-07-01

    The merger of the product portfolios of the former Siemens and Framatome fuel businesses gave rise to a new family of PWR products which combine the best features of the different technologies to enhance the main performance of each of the existing products. In this way, the technology of each of the three main fuel assembly types usually delivered by AREVA NP, namely Mark-BW{sup TM}, HTP{sup TM} and AFA 3G{sup TM} has been enriched by one or several components from the others which contributes to improve their robustness and to enhance their performance. The combined experience of AREVA's products shows that the ROBUST FUELGUARD{sup TM}, the HMP{sup TM} end grid, the MONOBLOC{sup TM} guide tube, a welded structure, M5{sup R} material for every zirconium component and an upper QUICK-DISCONNECT{sup TM} are key features for boosting fuel assembly robustness. The ROBUST FUELGUARD benefits from a broad experience demonstrating its high efficiency in stopping debris. In addition, its mechanical strength has been enhanced and the proven blade design homogenizes the downstream flow distribution to strongly reduce excitation of fuel rods. The resistance to rod-to-grid fretting resistance of AREVA's new products is completed by the use of a lower HMP grid with 8 lines of contact to insure low wear. The Monobloc guide tube with a diameter maximized to strengthen the fuel assembly stiffness, excludes through its uniform outer geometry any local condition which could weaken guide tube straightness. The application of a welded cage to all fuel assemblies of the new family of products in combination with stiffer guide tubes and optimized hold-down assures each fuel assembly enhanced resistance to distortion. The combination of these features has been widely demonstrated as an effective method to reduce the risk of incomplete RCCA insertion and significantly reduce assembly distortion. Thanks to its enhanced performance, M5 alloy insures that all fuel assemblies in the family

  12. Analysis of a Defected Dissimilar Metal Weld in a PWR Power Plant

    SciTech Connect

    Efsing, P.; Lagerstrom, J.

    2002-07-01

    During the refueling outage 2000, inspections of the RC-loops of one of the Ringhals PWR-units, Ringhals 4, indicated surface breaking defects in the axial direction of the piping in a dissimilar weld between the Low alloy steel nozzle and the stainless safe end in the hot leg. In addition some indications were found that there were embedded defects in the weld material. These defects were judged as being insignificant to the structural integrity. The welds were inspected in 1993 with the result that no significant indications were found. The weld it self is a double U weld, where the thickness of the material is ideally 79,5 mm. Its is constructed by Inconel 182 weld material. At the nozzle a buttering was applied, also by Inconel 182. The In-service inspection, ISI, of the object indicated four axial defects, 9-16 mm deep. During fabrication, the areas where the defects are found were repaired at least three times, onto a maximum depth of 32 mm. To evaluate the defects, 6 boat samples from the four axial defects were cut from the perimeter and shipped to the hot-cell laboratory for further examination. This examination revealed that the two deep defects had been under sized by the ISI outside the requirement set by the inspection tolerances, while the two shallow defects were over sized, but within the tolerances of the detection system. When studying the safety case it became evident that there were several missing elements in the way this problems is handled with respect to the Swedish safety evaluation code. Among these the most notable at the beginning was the absence of reliable fracture mechanical data such as crack growth laws and fracture toughness at elevated temperature. Both these questions were handled by the project. The fracture mechanical evaluation has focused on a fit for service principal. Thus defects both in the unaffected zones and the disturbed zones, boat sample cutouts, of the weld have been analyzed. With reference to the Swedish safety

  13. Gas bubbling-enhanced film boiling of Freon-11 on liquid metal pools. [PWR; BWR

    SciTech Connect

    Greene, G.A.

    1985-01-01

    In the analysis of severe core damage accidents in LWRs, a major driving force which must be considered in evaluating containment loading and fission product transport is the ex-vessel interaction between molten core debris and structural concrete. Two computer codes have been developed for this purpose, the CORCON-MOD2 model of ex-vessel, core concrete interactions and the VANESA model for aerosol generation and fission product release as a result of molten core-concrete interactions. Under a wide spectrum of reactor designs and accident sequences, it is possible for water to come into contact with the molten core debris and form a coolant pool overlying the core debris which is attacking the concrete. As the concrete decomposes, noncondensable gases are released, which bubble through the melt and across the boiling interface, affecting the liquid-liquid boiling process. Currently, the CORCON code includes the classical Berenson model for film boiling over a horizontal flat plate for this phenomenon. The objectives of this activity are to investigate the influence of transverse noncondensable gas flux on the magnitude of the stable liquid-liquid film boiling heat flux and develop a gas flux-enhanced, liquid-liquid film boiling model for incorporation into the CORCON-MOD2 computer code to replace or modify the Berenson model.

  14. Comparative analysis of isotopic composition of spent fuel from Takahama-3 PWR PIE database using TRIPOLI-PEPIN code

    SciTech Connect

    Lee, Y. K.

    2006-07-01

    Evaluation of isotopic composition of spent nuclear fuel is essential for reactor physics and fuel cycle back-end applications. A TRIPOLI-PEPIN coupled depletion code, TR4PEP, has been developed to meet these requirements. It combines the continuous-energy Monte Carlo transport code, TRIPOLI4.3 [1] and the point depletion code, PEPIN-2 [2], to perform the burnup dependent material data calculation. The depletion calculation flow of TR4PEP code has been presented on a previous study. Its application on PWR UO{sub 2} and MOX spent fuel has been validated against several international numerical benchmarks. Compared to industry standard deterministic cell codes and other Monte Carlo based depletion codes, TR4PEP deep-burn depletion calculations have shown satisfactory results. [3] In addition to the numerical benchmarks, the analysis of available post irradiation examination (PIE) results by TR4PEP is also important The PIE results at fuel assembly level are accessible only from spent fuel reprocessing plant and these data are not easy to use for code validation due to the dissolution of several assemblies in the same time. The PIE results at fuel pellet level depend not only on the method for the isotopic measurements but also on the irradiation environment and history. A free access PIE database on isotopic composition of spent nuclear fuel is obtainable from OECD/NEA. [4] Both PWR and BWR PIE data at fuel pellet level are taken into account in this database but the only 17 x 17 type PWR fuel available in this database is from Takahama-3 PIE results. To validate TR4PEP with Takahama-3 PIE results, two irradiated UO{sub 2} samples, SF95-4 from fuel assembly NT3G23 and SF97-5 from NT3G24, are considered in this study. Both samples have an initial {sup 235}U enrichment of 4.11 wt% and their burnup are respectively 36.69 and 47.03 GWd/t. Comparative analysis of isotopic composition from SF95-4 and SF97-5 including 19 actinides from {sup 234}U to {sup 247}Cm and 18

  15. Improvement of COBRA-TF for modeling of PWR cold- and hot-legs during reactor transients

    NASA Astrophysics Data System (ADS)

    Salko, Robert K.

    COBRA-TF is a two-phase, three-field (liquid, vapor, droplets) thermal-hydraulic modeling tool that has been developed by the Pacific Northwest Laboratory under sponsorship of the NRC. The code was developed for Light Water Reactor analysis starting in the 1980s; however, its development has continued to this current time. COBRA-TF still finds wide-spread use throughout the nuclear engineering field, including nuclear-power vendors, academia, and research institutions. It has been proposed that extension of the COBRA-TF code-modeling region from vessel-only components to Pressurized Water Reactor (PWR) coolant-line regions can lead to improved Loss-of-Coolant Accident (LOCA) analysis. Improved modeling is anticipated due to COBRA-TF's capability to independently model the entrained-droplet flow-field behavior, which has been observed to impact delivery to the core region[1]. Because COBRA-TF was originally developed for vertically-dominated, in-vessel, sub-channel flow, extension of the COBRA-TF modeling region to the horizontal-pipe geometries of the coolant-lines required several code modifications, including: • Inclusion of the stratified flow regime into the COBRA-TF flow regime map, along with associated interfacial drag, wall drag and interfacial heat transfer correlations, • Inclusion of a horizontal-stratification force between adjacent mesh cells having unequal levels of stratified flow, and • Generation of a new code-input interface for the modeling of coolant-lines. The sheer number of COBRA-TF modifications that were required to complete this work turned this project into a code-development project as much as it was a study of thermal-hydraulics in reactor coolant-lines. The means for achieving these tasks shifted along the way, ultimately leading the development of a separate, nearly completely independent one-dimensional, two-phase-flow modeling code geared toward reactor coolant-line analysis. This developed code has been named CLAP, for

  16. Non-Proliferative, Thorium-Based, Core and Fuel Cycle for Pressurized Water Reactors

    SciTech Connect

    Todosow M.; Todosow M.; Raitses, G. Galperin, A.

    2009-07-12

    Two of the major barriers to the expansion of worldwide adoption of nuclear power are related to proliferation potential of the nuclear fuel cycle and issues associated with the final disposal of spent fuel. The Radkowsky Thorium Fuel (RTF) concept proposed by Professor A. Radkowsky offers a partial solution to these problems. The main idea of the concept is the utilization of the seed-blanket unit (SBU) fuel assembly geometry which is a direct replacement for a 'conventional' assembly in either a Russian pressurized water reactor (VVER-1000) or a Western pressurized water reactor (PWR). The seed-blanket fuel assembly consists of a fissile (U) zone, known as seed, and a fertile (Th) zone known as blanket. The separation of fissile and fertile allows separate fuel management schemes for the thorium part of the fuel (a subcritical 'blanket') and the 'driving' part of the core (a supercritical 'seed'). The design objective for the blanket is an efficient generation and in-situ fissioning of the U233 isotope, while the design objective for the seed is to supply neutrons to the blanket in a most economic way, i.e. with minimal investment of natural uranium. The introduction of thorium as a fertile component in the nuclear fuel cycle significantly reduces the quantity of plutonium production and modifies its isotopic composition, reducing the overall proliferation potential of the fuel cycle. Thorium based spent fuel also contains fewer higher actinides, hence reducing the long-term radioactivity of the spent fuel. The analyses show that the RTF core can satisfy the requirements of fuel cycle length, and the safety margins of conventional pressurized water reactors. The coefficients of reactivity are comparable to currently operating VVER's/PWR's. The major feature of the RTF cycle is related to the total amount of spent fuel discharged for each cycle from the reactor core. The fuel management scheme adopted for RTF core designs allows a significant decrease in the

  17. Flow visualization study of inverted annular flow of post dryout heat transfer region. [PWR; BWR

    SciTech Connect

    Ishii, M.; De Jarlais, G.

    1985-01-01

    The inverted annular flow is important in the area of LWR accident analysis in terms of the maximum cladding temperature and effectiveness of the emergency core cooling. However, the inverted annular flow thermal-hydraulics is not well understood due to its special heat transfer condition of film boiling. The review of existing data indicates further research is needed in the areas of basic hydrodynamics related to liquid core disintegration mechanisms, slug and droplet formation, entrainment, and droplet size distributions. In view of this, the inverted flow is studied in detail experimentally. A new experimental apparatus has been constructed in which film boiling heat transfer can be established in a transparent test section. The test section consists of two coaxial quartz tubes. The annular gap between these two tubes is filled with a hot, clear fluid (syltherm 800) so as to maintain film boiling temperatures and heat transfer rates at the inner quartz tube wall. Data on liquid core stability, core break-up mechanism, and dispersed-core liquid slug and droplet sizes are obtained using F 113 as a test fluid. Both high speed movies and flash photographs (3 ..mu..sec) are used.

  18. The evaluation of iron-base hardfacing alloys on gate valves after cycling under simulated PWR conditions for one year

    SciTech Connect

    Murphy, E.V.; Inglis, I.; Ocken, H.

    1992-12-31

    Gate valves hardfaced with iron-base alloys were exposed for about one year to simulated PWR conditions. The hardfacing alloys tested were EB 5183, EVERIT 50, NOREM 01 and NOREM 04. A gate valve with Satellite 6 was included in the test program as a control standard. During the test period the valves were opened and closed 2000 times. The performance of the valves was assessed by periodic leak tests and visual and profilometric characterisation of sealing surfaces. At the end of the test program, the seats and discs were destructively examined. The various examinations indicated all the iron-base alloys were superior to Satellite 6. Based on the results of hot leakage tests, one valve with EB 5183 and the valve with NOREM 04 were the best performers.

  19. Effects of PbO on the oxide films of incoloy 800HT in simulated primary circuit of PWR

    NASA Astrophysics Data System (ADS)

    Tan, Yu; Yang, Junhan; Wang, Wanwan; Shi, Rongxue; Liang, Kexin; Zhang, Shenghan

    2016-05-01

    Effects of trace PbO on oxide films of Incoloy 800HT were investigated in simulated primary circuit water chemistry of PWR, also with proper Co addition. The trace PbO addition in high temperature water blocked the protective spinel oxides formation of the oxide films of Incoloy 800HT. XPS results indicated that the lead, added as PbO into the high temperature water, shows not only +2 valance but also +4 and 0 valances in the oxide film of 800HT co-operated with Fe, Cr and Ni to form oxides films. Potentiodynamic polarization results indicated that as PbO concentration increased, the current densities of the less protective oxide films of Incoloy 800HT decreased in a buffer solution tested at room temperature. The capacitance results indicated that the donor densities of oxidation film of Incoloy 800HT decreased as trace PbO addition into the high temperature water.

  20. Analysis of the performance of the Westinghouse reactor vessel level indicating system for tests at semiscale. [PWR

    SciTech Connect

    Hardy, J.E.; Miller, G.N.

    1982-10-01

    The Westinghouse Reactor Vessel Level Indicating System (RVLIS), a differential pressure level measurement system, was tested at SEMISCALE. This report contains the analyses of these tests and the conclusions of these analyses. The tests performed included small break and intermediate break tests. Also, frequency response and natural circulation tests were run and analyzed. The RVLIS always indicated a level less than the two phase froth level. The RVLIS output in early small break tests indicated a level 200 cm greater than actual collapsed liquid level. This discrepancy was caused by structural differences between SEMISCALE and a Westinghouse reactor. Once modifications were made so that SEMISCALE better simulated a Westinghouse PWR, the maximum difference between RVLIS and SEMISCALE instrumentation was 30 cm or 3% which is less than the stated uncertainty of the Westinghouse RVLIS.

  1. Effect of temperature and dissolved hydrogen on oxide films formed on Ni and Alloy 182 in simulated PWR water

    NASA Astrophysics Data System (ADS)

    Mendonça, R.; Bosch, R.-W.; Van Renterghem, W.; Vankeerberghen, M.; de Araújo Figueiredo, C.

    2016-08-01

    Alloy 182 is a nickel-based weld metal, which is susceptible to stress corrosion cracking in PWR primary water. It shows a peak in SCC susceptibility at a certain temperature and hydrogen concentration. This peak is related to the electrochemical condition where the Ni to NiO transition takes place. One hypothesis is that the oxide layer at this condition is not properly developed and so the material is not optimally protected against SCC. Therefore the oxide layer formed on Alloy 182 is investigated as a function of the dissolved hydrogen concentration and temperature around this Ni/NiO transition. Exposure tests were performed with Alloy 182 and Ni coupons in a PWR environment at temperatures between 300 °C and 345 °C and dissolved hydrogen concentration between 5 and 35 cc (STP)H2/kg. Post-test analysis of the formed oxide layers were carried out by SEM, EDS and XPS. The exposure tests with Ni coupons showed that the Ni/NiO transition curve is at a higher temperature than the curve based on thermodynamic calculations. The exposure tests with Alloy 182 showed that oxide layers were present at all temperatures, but that the morphology changed from spinel crystals to needle like oxides when the Ni/NiO transition curve was approached. Oxide layers were present below the Ni/NiO transition curve i.e. when the Ni coupon was still free of oxides. In addition an evolved slip dissolution model was proposed that could explain the observed experimental results and the peak in SCC susceptibility for Ni-based alloys around the Ni/NiO transition.

  2. VERA Core Simulator methodology for pressurized water reactor cycle depletion

    DOE PAGES

    Kochunas, Brendan; Collins, Benjamin; Stimpson, Shane; ...

    2017-01-12

    This paper describes the methodology developed and implemented in the Virtual Environment for Reactor Applications Core Simulator (VERA-CS) to perform high-fidelity, pressurized water reactor (PWR), multicycle, core physics calculations. Depletion of the core with pin-resolved power and nuclide detail is a significant advance in the state of the art for reactor analysis, providing the level of detail necessary to address the problems of the U.S. Department of Energy Nuclear Reactor Simulation Hub, the Consortium for Advanced Simulation of Light Water Reactors (CASL). VERA-CS has three main components: the neutronics solver MPACT, the thermal-hydraulic (T-H) solver COBRA-TF (CTF), and the nuclidemore » transmutation solver ORIGEN. This paper focuses on MPACT and provides an overview of the resonance self-shielding methods, macroscopic-cross-section calculation, two-dimensional/one-dimensional (2-D/1-D) transport, nuclide depletion, T-H feedback, and other supporting methods representing a minimal set of the capabilities needed to simulate high-fidelity models of a commercial nuclear reactor. Results are presented from the simulation of a model of the first cycle of Watts Bar Unit 1. The simulation is within 16 parts per million boron (ppmB) reactivity for all state points compared to cycle measurements, with an average reactivity bias of <5 ppmB for the entire cycle. Comparisons to cycle 1 flux map data are also provided, and the average 2-D root-mean-square (rms) error during cycle 1 is 1.07%. To demonstrate the multicycle capability, a state point at beginning of cycle (BOC) 2 was also simulated and compared to plant data. The comparison of the cycle 2 BOC state has a reactivity difference of +3 ppmB from measurement, and the 2-D rms of the comparison in the flux maps is 1.77%. Lastly, these results provide confidence in VERA-CS’s capability to perform high-fidelity calculations for practical PWR reactor problems.« less

  3. Nuclear Data Uncertainties for Typical LWR Fuel Assemblies and a Simple Reactor Core

    NASA Astrophysics Data System (ADS)

    Rochman, D.; Leray, O.; Hursin, M.; Ferroukhi, H.; Vasiliev, A.; Aures, A.; Bostelmann, F.; Zwermann, W.; Cabellos, O.; Diez, C. J.; Dyrda, J.; Garcia-Herranz, N.; Castro, E.; van der Marck, S.; Sjöstrand, H.; Hernandez, A.; Fleming, M.; Sublet, J.-Ch.; Fiorito, L.

    2017-01-01

    The impact of the current nuclear data library covariances such as in ENDF/B-VII.1, JEFF-3.2, JENDL-4.0, SCALE and TENDL, for relevant current reactors is presented in this work. The uncertainties due to nuclear data are calculated for existing PWR and BWR fuel assemblies (with burn-up up to 40 GWd/tHM, followed by 10 years of cooling time) and for a simplified PWR full core model (without burn-up) for quantities such as k∞, macroscopic cross sections, pin power or isotope inventory. In this work, the method of propagation of uncertainties is based on random sampling of nuclear data, either from covariance files or directly from basic parameters. Additionally, possible biases on calculated quantities are investigated such as the self-shielding treatment. Different calculation schemes are used, based on CASMO, SCALE, DRAGON, MCNP or FISPACT-II, thus simulating real-life assignments for technical-support organizations. The outcome of such a study is a comparison of uncertainties with two consequences. One: although this study is not expected to lead to similar results between the involved calculation schemes, it provides an insight on what can happen when calculating uncertainties and allows to give some perspectives on the range of validity on these uncertainties. Two: it allows to dress a picture of the state of the knowledge as of today, using existing nuclear data library covariances and current methods.

  4. Correlation and spectral measurements of fluctuating pressures and velocities in annular turbulent flow. [PWR; BWR

    SciTech Connect

    Wilson, R.J.; Jones, B.G.; Roy, R.P.

    1980-02-01

    An experimental study of the fluctuating velocity field, the fluctuating static wall pressure and the in-stream fluctuating static pressure in an annular turbulent air flow system with a radius ratio of 4.314 has been conducted. The study included direct measurements of the mean velocity profile, turbulent velocity field; fluctuating static wall pressure and in-stream fluctuating static pressure from which the statistical values of the turbulent intensity levels, power spectral densities of the turbulent quantities, the cross-correlation between the fluctuating static wall pressure and the fluctuating static pressure in the core region of the flow and the cross-correlation between the fluctuating static wall pressure and the fluctuating velocity field in the core region of the flow were obtained.

  5. Core-core and core-valence correlation

    NASA Technical Reports Server (NTRS)

    Bauschlicher, Charles W., Jr.; Langhoff, Stephen R.; Taylor, Peter R.

    1988-01-01

    The effect of (1s) core correlation on properties and energy separations was analyzed using full configuration-interaction (FCI) calculations. The Be 1 S - 1 P, the C 3 P - 5 S and CH+ 1 Sigma + or - 1 Pi separations, and CH+ spectroscopic constants, dipole moment and 1 Sigma + - 1 Pi transition dipole moment were studied. The results of the FCI calculations are compared to those obtained using approximate methods. In addition, the generation of atomic natural orbital (ANO) basis sets, as a method for contracting a primitive basis set for both valence and core correlation, is discussed. When both core-core and core-valence correlation are included in the calculation, no suitable truncated CI approach consistently reproduces the FCI, and contraction of the basis set is very difficult. If the (nearly constant) core-core correlation is eliminated, and only the core-valence correlation is included, CASSCF/MRCI approached reproduce the FCI results and basis set contraction is significantly easier.

  6. Design, Construction and Testing of an In-Pile Loop for PWR (Pressurized Water Reactor) Simulation.

    DTIC Science & Technology

    1987-06-01

    corrosion resistance in a steam environment. For this reason zircaloy - 2 is used 109 as the primary cladding material in Boiling Water Reactors (BWR...Unfortunately, zircaloy - 2 was found to have a high affinity for monoatomic hydrogen, which formed an intermetallic compound of zirconium-hydride. The...built, the Loop duplicates the core and Steam Generator fluid surface film differential temperatures , bulk fluid temperatures , and wall fluid shear

  7. TRAC-PF1/MOD1 US/Japanese PWR conservative LOCA prediction

    SciTech Connect

    Gruen, G E; Fisher, J E

    1987-11-01

    This report documents the results of a 200%, double-ended, cold-leg-break, loss-of-coolant-accident (LOCA) calculation using the TRAC-PF1/MOD1 computer code. The reactor system represented a typical United States/Japanese pressurized water reactor with a 15 x 15 fuel bundle arrangement 12-ft long, four loops, and cold-leg Emergency Core Cooling (ECC) Systems. Conservation boundary and initial conditions were used. Reactor power was 102% of the 3250 MWt rated power, decay heat was set to 120% of American Nuclear Society Standard 5.1, highest core lifetime values for power peaking and fuel stored energy were used, and the LOCA occurred simultaneously with a loss of offsite power. Best estimate assumptions were used for the break flow model, fuel rod heat transfer and metal-water reaction correlations, and steady-state fuel temperature profiles. A flow blockage model, having the capability to account for the effects of cladding ballooning or rupturing, was not used. Except for these best estimate assumptions, the boundary and initial conditions were consistent with those used in licensing calculations. Maximum fuel rod temperatures were 1380 K (2020/sup 0/F) and 1040 K (1410/sup 0/F) on the hottest evaluation model rod and hottest best estimate rod, respectively. The high reported values or fuel cladding temperature were a direct consequence of the conservative boundary and initial conditions used for the calculation, primarily the 2% overpower condition, the core decay heat assumption, and the degraded ECCS. The calculation demonstrated successful core reflooding before 1478 K (2200/sup 0/F) cladding temperature was exceeded on any fuel rod. 7 refs., 47 figs., 5 tabs.

  8. Heat transfer between immiscible liquids enhanced by gas bubbling. [PWR; BWR

    SciTech Connect

    Greene, G.A.; Schwarz, C.E.; Klages, J.; Klein, J.

    1982-08-01

    The phenomena of core-concrete interactions impact upon containment integrity of light water reactors (LWR) following postulated complete meltdown of the core by containment pressurization, production of combustible gases, and basemat penetration. Experiments have been performed with non-reactor materials to investigate one aspect of this problem, heat transfer between overlying immiscible liquids whose interface is disturbed by a transverse non-condensable gas flux emanating from below. Hydrodynamic studies have been performed to test a criterion for onset of entrainment due to bubbling through the interface and subsequent heat transfer studies were performed to assess the effect of bubbling on interfacial heat transfer rates, both with and without bubble induced entrainment. Non-entraining interfacial heat transfer data with mercury-water/oil fluid pairs were observed to be bounded from below within a factor of two to three by the Szekeley surface renewal heat transfer model. However heat transfer data for fluid pairs which are found to entrain (water-oil), believed to be characteristic of molten reactor core-concrete conditions, were measured to be up to two orders of magnitude greater than surface renewal predictions and are calculated by a simple entrainment heat transfer model.

  9. Scoping design analyses for optimized shipping casks containing 1-, 2-, 3-, 5-, 7-, or 10-year-old PWR spent fuel

    SciTech Connect

    Bucholz, J.A.

    1983-01-01

    This report details many of the interrelated considerations involved in optimizing large Pb, Fe, or U-metal spent fuel shipping casks containing 1, 2, 3, 5, 7, or 10-year-old PWR fuel assemblies. Scoping analyses based on criticality, shielding, and heat transfer considerations indicate that some casks may be able to hold as many as 18 to 21 ten-year-old PWR fuel assemblies. In the criticality section, a new type of inherently subcritical fuel assembly separator is described which uses hollow, borated stainless-steel tubes in the wall-forming structure between the assemblies. In another section, details of many n/..gamma.. shielding optimization studies are presented, including the optimal n/..gamma.. design points and the actual shielding requirements for each type of cask as a function of the age of the spent fuel and the number of assemblies in the cask. Multigroup source terms based on ORIGEN2 calculations at these and other decay times are also included. Lastly, the numerical methods and experimental correlations used in the steady-state and transient heat transfer analyses are fully documented, as are pertinent aspects of the SCOPE code for Shipping Cask Optimization and Parametric Evaluation. (While only casks for square, intact PWR fuel assemblies were considered in this study, the SCOPE code may also be used to design and analyze casks containing canistered spent fuel or other waste material. An abbreviated input data guide is included as an appendix).

  10. Summary report on optimized designs for shipping casks containing 2-, 3-, 5-, 7-, or 10-year-old PWR spent fuel

    SciTech Connect

    Bucholz, J.A.

    1983-04-01

    The purpose of this study was to develop new conceptual designs for large Pb, Fe, and U-shielded spent fuel casks which have been optimized for the shipment of 2-, 3-, 5-, 7-, or 10-year-old PWR spent fuel assemblies. Design specifications for about 100 cases of potential interest are presented along with a brief 20-page synopsis of the associated analyses. Optimized shielding requirements are presented for each type of cask as a function of the age of the spent fuel and the number of assemblies in the cask. With respect to criticality, a new type of inherently subcritical fuel assembly separator is described which uses hollow, borated stainless-steel tubes in the wall-forming structure between the assemblies. Steady-state and transient heat transfer analyses for casks under nominal and accident conditions were performed using the SCOPE code for Shipping Cask Optimization and Parametric Evaluation. Based on criticality, shielding, and heat transfer considerations, it appears that optimized cask designs could be developed to carry 15 to 18 five-year-old PWR fuel assemblies or as many as 18 to 21 ten-year-old PWR fuel assemblies. 4 figures, 4 tables.

  11. Preliminary design report for SCDAP/RELAP5 lower core plate model

    SciTech Connect

    Coryell, E.W.; Griffin, F.P.

    1998-07-01

    The SCDAP/RELAP5 computer code is a best-estimate analysis tool for performing nuclear reactor severe accident simulations. Under primary sponsorship of the US Nuclear Regulatory Commission (NRC), Idaho National Engineering and Environmental Laboratory (INEEL) is responsible for overall maintenance of this code and for improvements for pressurized water reactor (PWR) applications. Since 1991, Oak Ridge National Laboratory (ORNL) has been improving SCDAP/RELAP5 for boiling water reactor (BWR) applications. The RELAP5 portion of the code performs the thermal-hydraulic calculations for both normal and severe accident conditions. The structures within the reactor vessel and coolant system can be represented with either RELAP5 heat structures or SCDAP/RELAP5 severe accident structures. The RELAP5 heat structures are limited to normal operating conditions (i.e., no structural oxidation, melting, or relocation), while the SCDAP portion of the code is capable of representing structural degradation and core damage progression that can occur under severe accident conditions. DCDAP/RELAP5 currently assumes that molten material which leaves the core region falls into the lower vessel head without interaction with structural materials. The objective of this design report is to describe the modifications required for SCDAP/RELAP5 to treat the thermal response of the structures in the core plate region as molten material relocates downward from the core, through the core plate region, and into the lower plenum. This has been a joint task between INEEL and ORNL, with INEEL focusing on PWR-specific design, and ORNL focusing upon the BWR-specific aspects. Chapter 2 describes the structures in the core plate region that must be represented by the proposed model. Chapter 3 presents the available information about the damage progression that is anticipated to occur in the core plate region during a severe accident, including typical SCDAP/RELAP5 simulation results. Chapter 4 provides a

  12. Los Alamos PWR decay-heat-removal studies. Summary results and conclusions

    SciTech Connect

    Boyack, B E; Henninger, R J; Horley, E; Lime, J F; Nassersharif, B; Smith, R

    1986-03-01

    The adequacy of shutdown-decay-heat removal in pressurized water reactors (PWRs) is currently under investigation by the Nuclear Regulatory Commission. One part of this effort is the review of feed-and-bleed procedures that could be used if the normal cooling mode through the steam generators were unavailable. Feed-and-bleed cooling is effected by manually activating the high-pressure injection (HPI) system and opening the power-operated relief valves (PORVs) to release the core decay energy. The feasibility of the feed-and-bleed concept as a diverse mode of heat removal has been evaluated at the Los Alamos National Laboratory. The TRAC-PF1 code has been used to predict the expected performance of the Oconee-1 and Calvert Cliffs-1 reactors of Bobcock and Wilcox and Combustion Engineering, respectively, and the Zion-1 and H.B. Robinson-2 plants of Westinghouse. Feed and bleed was successfully applied in each of the four plants studied, provided it was initiated no later than the time of loss of secondary heat sink. Feed and bleed was successfully applied in two of the plants, Oconee-1 and Zion-1, provided it was initiated no later than the time of primary system saturation. Feed and bleed in Calvert Cliffs-1 when initiated at the time of primary system saturation did result in core dryout; however, the core heatup was eventually terminated by coolant injection. Feed-and-bleed initiation at primary system saturation was not studied for H.B. Robinson-2. Insights developed during the analyses of specific plant transients have been identified and documented. 33 refs., 107 figs., 26 tabs.

  13. Monitoring system for a liquid-cooled nuclear fission reactor. [PWR

    DOEpatents

    DeVolpi, A.

    1984-07-20

    The invention provides improved means for detecting the water levels in various regions of a water-cooled nuclear power reactor, viz., in the downcomer, in the core, in the inlet and outlet plenums, at the head, and elsewhere; and also for detecting the density of the water in these regions. The invention utilizes a plurality of exterior gamma radiation detectors and a collimator technique operable to sense separate regions of the reactor vessel to give respectively, unique signals for these regions, whereby comparative analysis of these signals can be used to advise of the presence and density of cooling water in the vessel.

  14. Academic Rigor: The Core of the Core

    ERIC Educational Resources Information Center

    Brunner, Judy

    2013-01-01

    Some educators see the Common Core State Standards as reason for stress, most recognize the positive possibilities associated with them and are willing to make the professional commitment to implementing them so that academic rigor for all students will increase. But business leaders, parents, and the authors of the Common Core are not the only…

  15. Academic Rigor: The Core of the Core

    ERIC Educational Resources Information Center

    Brunner, Judy

    2013-01-01

    Some educators see the Common Core State Standards as reason for stress, most recognize the positive possibilities associated with them and are willing to make the professional commitment to implementing them so that academic rigor for all students will increase. But business leaders, parents, and the authors of the Common Core are not the only…

  16. Buoyancy, transport, and head loss of fibrous reactor insulation. Rev. 1. [PWR; BWR

    SciTech Connect

    Brocard, D.N.

    1983-07-01

    In the event of a Loss of Coolant Accident (LOCA) in a nuclear power plant, it is possible that insulation for pipes or other items inside the containment building could be dislodged by the high energy break jet. To help in assessing the possible effect of detached insulation on the ECCS, buoyancy, transport, and head loss characteristics of the insulation were studied experimentally. Three types of insulation pillows with mineral wood and fiberglass cores were tested in undamaged state, with their covers opened and with the insulation core in broken-up and shredded conditions. Small samples of reflective metallic and closed cell insulations were also tested for transport and buoyancy. This revision 1 of NUREG/CR-2982 is an expanded version of the original document, increasing the range of measured head losses through beds of accumulated fragments to a thickness of 10 inches. New fitting formulae were also developed to cover the expanded data range, replacing the formulae set forth originally which, when extrapolated over the new data range, sometimes gave head losses lower than measured. Uncertainty bands were also developed for the new fitting formulae.

  17. Challenges in the development of high-fidelity LWR core neutronics tools

    SciTech Connect

    Smith, K.; Forget, B.

    2013-07-01

    Modern computing has made possible the solution of extremely large-scale reactor simulations, and the literature has numerous examples of high-resolution methods (often Monte Carlo) applied to full-core reactor problems. However, there are currently no examples in the literature of application of such 'High-Fidelity' or 'First Principles' methods to operating Light Water Reactor (LWR) analysis. This paper seeks to remind code developers, project managers, and analysts of the many important aspects of LWR simulation that must be incorporated to produce truly high-fidelity analysis tools. The authors offer a monetary prize to the first person (or group) that successfully solves a new two-cycle operational PWR depletion benchmark problem using high-fidelity tools and demonstrates acceptable accuracy by comparison with measured operational plant data (open source) provided to the reactor analysis community. (authors)

  18. Benchmark of SCALE (SAS2H) isotopic predictions of depletion analyses for San Onofre PWR MOX fuel

    SciTech Connect

    Hermann, O.W.

    2000-02-01

    The isotopic composition of mixed-oxide (MOX) fuel, fabricated with both uranium and plutonium, after discharge from reactors is of significant interest to the Fissile Materials Disposition Program. The validation of the SCALE (SAS2H) depletion code for use in the prediction of isotopic compositions of MOX fuel, similar to previous validation studies on uranium-only fueled reactors, has corresponding significance. The EEI-Westinghouse Plutonium Recycle Demonstration Program examined the use of MOX fuel in the San Onofre PWR, Unit 1, during cycles 2 and 3. Isotopic analyses of the MOX spent fuel were conducted on 13 actinides and {sup 148}Nd by either mass or alpha spectrometry. Six fuel pellet samples were taken from four different fuel pins of an irradiated MOX assembly. The measured actinide inventories from those samples has been used to benchmark SAS2H for MOX fuel applications. The average percentage differences in the code results compared with the measurement were {minus}0.9% for {sup 235}U and 5.2% for {sup 239}Pu. The differences for most of the isotopes were significantly larger than in the cases for uranium-only fueled reactors. In general, comparisons of code results with alpha spectrometer data had extreme differences, although the differences in the calculations compared with mass spectrometer analyses were not extremely larger than that of uranium-only fueled reactors. This benchmark study should be useful in estimating uncertainties of inventory, criticality and dose calculations of MOX spent fuel.

  19. Comparison of PWR - Burnup calculations with SCALE 5.0/TRITON other burnup codes and experimental results

    SciTech Connect

    Oberle, P.; Broeders, C. H. M.; Dagan, R.

    2006-07-01

    The increasing tendency towards fuel lifetime extension in thermal nuclear reactors motivated validation work for available evaluation tools for nuclear fuel burnup calculations. In this study two deterministic codes with different transport solvers and one Monte Carlo method are investigated. The code system KAPROS/KARBUS uses the classical deterministic First Collision Probability method utilizing a cylinderized Wigner-Seitz cell. In the SCALES.0/TRITON/NEWT code the Extended Step Characteristic method is applied. In a first step the two deterministic codes are compared with experimental results from the KWO-Isotope Correlation Experiment up to 30 MWD/kg HM burnup, published in 1981. Two pin cell calculations are analyzed by comparison of calculated and experimental results for important heavy isotope vectors. The results are very satisfactory. Subsequently, further validation at higher burnup (< 80 MWD/kg HM) is provided by comparison of the two deterministic codes and the Monte Carlo based burnup code MONTEBURNS for PWR UO{sub 2} fuel assembly calculations. Possible reasons for differences in the results are analyzed and discussed. Especially the influence of cross section data and processing is presented. (authors)

  20. OBSERVATIONS AND IMPLICATIONS OF INTERGRANULAR STRESS CORROSION CRACK GROWTH OF ALLOY 152 WELD METALS IN SIMULATED PWR PRIMARY WATER

    SciTech Connect

    Toloczko, Mychailo B.; Olszta, Matthew J.; Overman, Nicole R.; Bruemmer, Stephen M.

    2013-08-15

    Significant intergranular (IG) crack growth during stress corrosion cracking (SCC) tests has been documented during tests in simulated PWR primary water on two alloy 152 specimens cut from a weldment produced by ANL. The cracking morphology was observed to change from transgranular (TG) to mixed mode (up to ~60% IG) during gentle cycling and cycle + hold loading conditions. Measured crack growth rates under these conditions often suggested a moderate degree of environmental enhancement consistent with faster growth on grain boundaries. However, overall SCC propagation rates at constant stress intensity (K) or constant load were very low in all cases. Initial SCC rates up to 6x10-9 mm/s were occasionally measured, but constant K/load growth rates dropped below ~1x10-9 mm/s with time even when significant IG engagement existed. Direct comparisons were made among loading conditions, measured crack growth response and cracking morphology during each test to assess IGSCC susceptibility of the alloy 152 specimens. These results were analyzed with respect to our previous SCC crack growth rate measurements on alloy 152/52 welds.

  1. In-plant test and evaluation of the neutron collar for verification of PWR fuel assemblies at Resende, Brazil

    SciTech Connect

    Menlove, H.O.; Marzo, M.A.S.; de Almeida, S.G.; de Almeida, M.C.; Moitta, L.P.M.; Conti, L.F.; de Paiva, J.R.T.

    1985-11-01

    The neutron-coincidence collar has been evaluated for the measurement of pressurized-water reactor (PWR) fuel assemblies at the Fabrica de Elementos Combustiveis plant in Resende, Brazil. This evaluation was part of the cooperative-bilateral-safeguards technical-exchange program between the United States and Brazil. The neutron collar measures the STVU content per unit length of full fuel assemblies using neutron interrogation and coincidence counting. The STYU content is measured in the passive mode without the AmLi neutron-interrogation source. The extended evaluation took place over a period of 6 months with both scanning and single-zone measurements. The results of the tests gave a coincidence-response standard deviation of 0.7% (sigma = 1.49% for mass) for the active case and 2.5% for the passive case in 1000-s measurement times. The length measurement in the scanning mode was accurate to 0.77%. The accuracies of different calibration methods were evaluated and compared.

  2. Effect of surface state on the oxidation behavior of welded 308L in simulated nominal primary water of PWR

    NASA Astrophysics Data System (ADS)

    Ming, Hongliang; Zhang, Zhiming; Wang, Jiazhen; Zhu, Ruolin; Ding, Jie; Wang, Jianqiu; Han, En-Hou; Ke, Wei

    2015-05-01

    The oxidation behavior of 308L weld metal (WM) with different surface state in the simulated nominal primary water of pressurized water reactor (PWR) was studied by scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD) analyzer and X-ray photoelectron spectroscopy (XPS). After 480 h immersion, a duplex oxide film composed of a Fe-rich outer layer (Fe3O4, Fe2O3 and a small amount of NiFe2O4, Ni(OH)2, Cr(OH)3 and (Ni, Fe)Cr2O4) and a Cr-rich inner layer (FeCr2O4 and NiCr2O4) can be formed on the 308L WM samples with different surface state. The surface state has no influence on the phase composition of the oxide films but obviously affects the thickness of the oxide films and the morphology of the oxides (number & size). With increasing the density of dislocations and subgrain boundaries in the cold-worked superficial layer, the thickness of the oxide film, the number and size of the oxides decrease.

  3. Characterization of interfacial reactions and oxide films on 316L stainless steel in various simulated PWR primary water environments

    NASA Astrophysics Data System (ADS)

    Chen, Junjie; Xiao, Qian; Lu, Zhanpeng; Ru, Xiangkun; Peng, Hao; Xiong, Qi; Li, Hongjuan

    2017-06-01

    The effect of water chemistry on the electrochemical and oxidizing behaviors of 316L SS was investigated in hydrogenated, deaerated and oxygenated PWR primary water at 310 °C. Water chemistry significantly influenced the electrochemical impedance spectroscopy parameters. The highest charge-transfer resistance and oxide-film resistance occurred in oxygenated water. The highest electric double-layer capacitance and constant phase element of the oxide film were in hydrogenated water. The oxide films formed in deaerated and hydrogenated environments were similar in composition but different in morphology. An oxide film with spinel outer particles and a compact and Cr-rich inner layer was formed in both hydrogenated and deaerated water. Larger and more loosely distributed outer oxide particles were formed in deaerated water. In oxygenated water, an oxide film with hematite outer particles and a porous and Ni-rich inner layer was formed. The reaction kinetics parameters obtained by electrochemical impedance spectroscopy measurements and oxidation film properties relating to the steady or quasi-steady state conditions in the time-period of measurements could provide fundamental information for understanding stress corrosion cracking processes and controlling parameters.

  4. Linking Grain Boundary Microstructure to Stress Corrosion Cracking of Cold Rolled Alloy 690 in PWR Primary Water

    SciTech Connect

    Bruemmer, Stephen M.; Olszta, Matthew J.; Toloczko, Mychailo B.; Thomas, Larry E.

    2012-10-01

    Grain boundary microstructures and microchemistries are examined in cold-rolled alloy 690 tubing and plate materials and comparisons are made to intergranular stress corrosion cracking (IGSCC) behavior in PWR primary water. Chromium carbide precipitation is found to be a key aspect for materials in both the mill annealed and thermally treated conditions. Cold rolling to high levels of reduction was discovered to produce small IG voids and cracked carbides in alloys with a high density of grain boundary carbides. The degree of permanent grain boundary damage from cold rolling was found to depend directly on the initial IG carbide distribution. For the same degree of cold rolling, alloys with few IG precipitates exhibited much less permanent damage. Although this difference in grain boundary damage appears to correlate with measured SCC growth rates, crack tip examinations reveal that cracked carbides appeared to blunt propagation of IGSCC cracks in many cases. Preliminary results suggest that the localized grain boundary strains and stresses produced during cold rolling promote IGSCC susceptibility and not the cracked carbides and voids.

  5. Ligand activation induces different conformational changes in CXCR3 receptor isoforms as evidenced by plasmon waveguide resonance (PWR).

    PubMed

    Boyé, K; Billottet, C; Pujol, N; Alves, I D; Bikfalvi, A

    2017-09-06

    The chemokine receptor CXCR3 plays important roles in angiogenesis, inflammation and cancer. Activation studies and biological functions of CXCR3 are complex due to the presence of spliced isoforms. CXCR3-A is known as a pro-tumor receptor whereas CXCR3-B exhibits anti-tumor properties. Here, we focused on the conformational change of CXCR3-A and CXCR3-B after agonist or antagonist binding using Plasmon Waveguide Resonance (PWR). Agonist stimulation induced an anisotropic response with very distinct conformational changes for the two isoforms. The CXCR3 agonist bound CXCR3-A with higher affinity than CXCR3-B. Using various concentrations of SCH546738, a CXCR3 specific inhibitor, we demonstrated that low SCH546738 concentrations (≤1 nM) efficiently inhibited CXCR3-A but not CXCR3-B's conformational change and activation. This was confirmed by both, biophysical and biological methods. Taken together, our study demonstrates differences in the behavior of CXCR3-A and CXCR3-B upon ligand activation and antagonist inhibition which may be of relevance for further studies aimed at specifically inhibiting the CXCR3A isoform.

  6. Analysis of experimental measurements of PWR fresh and spent fuel assemblies using Self-Interrogation Neutron Resonance Densitometry

    NASA Astrophysics Data System (ADS)

    LaFleur, Adrienne M.; Menlove, Howard O.

    2015-05-01

    Self-Interrogation Neutron Resonance Densitometry (SINRD) is a new NDA technique that was developed at Los Alamos National Laboratory (LANL) to improve existing nuclear safeguards measurements for LWR fuel assemblies. The SINRD detector consists of four fission chambers (FCs) wrapped with different absorber filters to isolate different parts of the neutron energy spectrum and one ion chamber (IC) to measure the gross gamma rate. As a result, two different techniques can be utilized using the same SINRD detector unit and hardware. These techniques are the Passive Neutron Multiplication Counter (PNMC) method and the SINRD method. The focus of the work described in this paper is the analysis of experimental measurements of fresh and spent PWR fuel assemblies that were performed at LANL and the Korea Atomic Energy Research Institute (KAERI), respectively, using the SINRD detector. The purpose of these experiments was to assess the following capabilities of the SINRD detector: 1) reproducibility of measurements to quantify systematic errors, 2) sensitivity to water gap between detector and fuel assembly, 3) sensitivity and penetrability to the removal of fuel rods from the assembly, and 4) use of PNMC/SINRD ratios to quantify neutron multiplication and/or fissile content. The results from these simulations and measurements provide valuable experimental data that directly supports safeguards research and development (R&D) efforts on the viability of passive neutron NDA techniques and detector designs for partial defect verification of spent fuel assemblies.

  7. Criticality evaluation of control component credited mixed zone spent and fresh fuel storage in high density PWR racks

    SciTech Connect

    Bilovsky, V.; Redmond, E.; Walker, C.; Ivanov, K.

    2006-07-01

    To expand the set of assemblies that qualify for storage in high-density racks, a mixed zone analysis may be performed where repeating pattern configurations within the rack are prescribed. In a mixed zone analysis, assemblies that are more reactive (low burnup) are stored adjacent to less reactive (highly burned) assemblies, thereby meeting the same overall criticality requirements as with the uniform burnup/enrichment analysis. The Arkansas Nuclear One (ANO) Plant has faced several challenges with respect to their spent fuel storage that reach beyond simply the number of spent fuel assemblies and available storage cells. These issues have resulted in the need for ANO to use an advanced storage strategy. In addition to using the mixed zone burnup approach in the high-density racks, ANO also proposed a new solution involving credit for control components in the spent fuel pool. ANO submitted an amendment of their spent fuel pool technical specifications to the Nuclear Regulatory Commission (NRC) based on the evaluation performed by Holtec International that was subsequently approved. This paper presents a description of the overall methodology used for supporting the submittal, and provides further discussion regarding the reactivity effect of control rods in a PWR spent fuel pool. (authors)

  8. Determination of Bandwidths of PWR-UO2 Spent Fuel Radionuclide Inventory Based on Real Operational History Data

    NASA Astrophysics Data System (ADS)

    Fast, Ivan; Aksyutina, Yuliya; Tietze-Jaensch, Holger; Bosbach, Dirk

    2016-08-01

    An important requirement for the official approval of the safe final disposal of SNF is a comprehensive specification and declaration of the nuclear inventory in SNF by the waste supplier. In the verification process both the radionuclide (RN) activities and the associated uncertainties are required. Burn-up (BU) calculations based on typical and generic reactor operational parameters do not encompass any possible uncertainties observed in real reactor operations. At the same time, details of irradiation history are often missing, which complicates the assessment of declared RN inventories. Here, we present a set of burn-up calculations, in which the real operational histories of 339 published or anonymized PWR fuel assemblies (FA) are taken into account. These histories provide information about ranges of values of the associated secondary reactor parameters (SRP), which are useful for the “SRP analysis”. Hence, we can calculate realistic variations in the spectrum of RN inventories. SCALE 6.1 with the ENDF/B-VII.0 library has been employed for the burn-up calculations. The results have been validated using experimental measurements from the online database SFCOMPO.

  9. In-Situ NDT Measurements of Irradiation Induced Swelling PWR Core Internal Components; Phase 3: Correlation of Void Swelling and Material Properties of Austenitic Steels

    SciTech Connect

    I.Balachov; F. Garner; S-G. Kumatori-cho; Y. Isobe

    2004-04-01

    OAK-B135 The objective of the project is to examine and develop in-situ nondestructive testing (NDT) techniques for measuring irradiation induced swelling in the internal components for PWRs. This report documents the third phase effort on establishing experimental correlations of the irradiation induced void swelling and measurable material properties of austenitic steels and, eventually, correlation of swelling and signals of the developed swelling sensors. Experimental stainless steel irradiated at high neutron fluences are presented. Theoretical aspects of the influence of void swelling on electrical resistivity and ultrasound velocity are outlined. Swelling-material properties correlations were recommended for quantitative interpretation of swelling measurements.

  10. Effect of core strength on the measure of power in the extremities.

    PubMed

    Shinkle, Justin; Nesser, Thomas W; Demchak, Timothy J; McMannus, David M

    2012-02-01

    The purpose of this study was to (a) develop a functional field test to assess the role of the core musculature and its impact on sport performance in an athletic population and (b) develop a functional field test to determine how well the core can transfer forces from the lower to the upper extremities. Twenty-five DI collegiate football players performed medicine ball throws (forward, reverse, right, and left) in static and dynamic positions. The results of the medicine ball throws were compared with several athletic performance measurements: 1 repetition maximum (1RM) squat, squat kg/bw, 1RM bench press, bench kg/bw, countermovement vertical jump (CMJ), 40-yd dash (40 yd), and proagility (PrA). Push press power (PWR) was used to measure the transfer of forces through the body. Several correlations were found in both the static and dynamic medicine ball throws when compared with the performance measures. Static reverse correlated with CMJ (r = 0.44), 40 yd (r = 0.5), and PrA (r = 0.46). Static left correlated with bench kg/bw (0.42), CMJ (0.44), 40 yd (0.62), and PrA (0.59). Static right also correlated with bench kg/bw (0.41), 40 yd (0.44), and PrA (0.65). Dynamic forward (DyFw) correlated with the 1RM squat (r = 0.45) and 1RM bench (0.41). Dynamic left and Dynamic right correlated with CMJ, r = 0.48 and r = 0.40, respectively. Push press power correlated with bench kg/bw (0.50), CMJ (0.48), and PrA (0.48). A stepwise regression for PWR prediction identified 1RM squat as the best predictor. The results indicate that core strength does have a significant effect on an athlete's ability to create and transfer forces to the extremities. Currently, plank exercises are considered an adequate method of training the core for athletes to improve core strength and stability. This is a problem because it puts the athletes in a nonfunctional static position that is very rarely replicated in the demands of sport-related activities. The core is the center of most kinetic

  11. Coring Sample Acquisition Tool

    NASA Technical Reports Server (NTRS)

    Haddad, Nicolas E.; Murray, Saben D.; Walkemeyer, Phillip E.; Badescu, Mircea; Sherrit, Stewart; Bao, Xiaoqi; Kriechbaum, Kristopher L.; Richardson, Megan; Klein, Kerry J.

    2012-01-01

    A sample acquisition tool (SAT) has been developed that can be used autonomously to sample drill and capture rock cores. The tool is designed to accommodate core transfer using a sample tube to the IMSAH (integrated Mars sample acquisition and handling) SHEC (sample handling, encapsulation, and containerization) without ever touching the pristine core sample in the transfer process.

  12. Toroidal converter core

    NASA Technical Reports Server (NTRS)

    Mclyman, W. T.

    1977-01-01

    Improved approach consists of cut and uncut cores nested in concentric configuration. Cores are made by winding steel ribbon on mandrel and impregnating with epoxy to bond layers together. Gap is made by cutting across wound and bonded core. Rough ends are ground or lapped.

  13. Core Competence and Education.

    ERIC Educational Resources Information Center

    Holmes, Gary; Hooper, Nick

    2000-01-01

    Outlines the concept of core competence and applies it to postcompulsory education in the United Kingdom. Adopts an educational perspective that suggests accreditation as the core competence of universities. This economic approach suggests that the market trend toward lifetime learning might best be met by institutions developing a core competence…

  14. The effects of stainless steel radial reflector on core reactivity for small modular reactor

    SciTech Connect

    Kang, Jung Kil Hah, Chang Joo; Cho, Sung Ju Seong, Ki Bong

    2016-01-22

    Commercial PWR core is surrounded by a radial reflector, which consists of a baffle and water. Radial reflector is designed to reflect neutron back into the core region to improve the neutron efficiency of the reactor and to protect the reactor vessels from the embrittling effects caused by irradiation during power operation. Reflector also helps to flatten the neutron flux and power distributions in the reactor core. The conceptual nuclear design for boron-free small modular reactor (SMR) under development in Korea requires to have the cycle length of 4∼5 years, rated power of 180 MWth and enrichment less than 5 w/o. The aim of this paper is to analyze the effects of stainless steel radial reflector on the performance of the SMR using UO{sub 2} fuels. Three types of reflectors such as water, water/stainless steel 304 mixture and stainless steel 304 are selected to investigate the effect on core reactivity. Additionally, the thickness of stainless steel and double layer reflector type are also investigated. CASMO-4/SIMULATE-3 code system is used for this analysis. The results of analysis show that single layer stainless steel reflector is the most efficient reflector.

  15. The effects of stainless steel radial reflector on core reactivity for small modular reactor

    NASA Astrophysics Data System (ADS)

    Kang, Jung Kil; Hah, Chang Joo; Cho, Sung Ju; Seong, Ki Bong

    2016-01-01

    Commercial PWR core is surrounded by a radial reflector, which consists of a baffle and water. Radial reflector is designed to reflect neutron back into the core region to improve the neutron efficiency of the reactor and to protect the reactor vessels from the embrittling effects caused by irradiation during power operation. Reflector also helps to flatten the neutron flux and power distributions in the reactor core. The conceptual nuclear design for boron-free small modular reactor (SMR) under development in Korea requires to have the cycle length of 4˜5 years, rated power of 180 MWth and enrichment less than 5 w/o. The aim of this paper is to analyze the effects of stainless steel radial reflector on the performance of the SMR using UO2 fuels. Three types of reflectors such as water, water/stainless steel 304 mixture and stainless steel 304 are selected to investigate the effect on core reactivity. Additionally, the thickness of stainless steel and double layer reflector type are also investigated. CASMO-4/SIMULATE-3 code system is used for this analysis. The results of analysis show that single layer stainless steel reflector is the most efficient reflector.

  16. Detection rate evaluation of ex-core detectors in the subcritical OPR-1000 reactor

    SciTech Connect

    Won, B. H.; Shin, C. H.; Kim, S. H.; Kim, H. C.; Park, J. J.; Kim, J. K.

    2012-07-01

    The OPR-1000 is a PWR reactor developed in Korea. One-type ex-core detectors for monitoring of power distributions were installed in the OPR-1000 reactor to alternate the three-types of the ex-core detectors. For the verification of the detection performances, neutron transport calculation was performed by using MCNP5 code. The reaction rate in the ex-core detectors and the neutron flux were evaluated by using MCNP5 code as changing the boron concentration from 1800 ppm to 1122 ppm in the subcritical condition. The reaction rate results in fission chamber show that minimum and maximum values are 0.03577 and 3.33563 reactions/cm{sup 3}-sec, respectively. This study can be directly used for the verification and improvement of fission chamber performance in using one-type ex-core detector. Also, it can be utilized for the production of the reference data in determining neutron source strength. It is expected the proposed simulation method can be utilized to the improvement of the dose monitoring system. (authors)

  17. Banded transformer cores

    NASA Technical Reports Server (NTRS)

    Mclyman, C. W. T. (Inventor)

    1974-01-01

    A banded transformer core formed by positioning a pair of mated, similar core halves on a supporting pedestal. The core halves are encircled with a strap, selectively applying tension whereby a compressive force is applied to the core edge for reducing the innate air gap. A dc magnetic field is employed in supporting the core halves during initial phases of the banding operation, while an ac magnetic field subsequently is employed for detecting dimension changes occurring in the air gaps as tension is applied to the strap.

  18. On-line measurements of RuO{sub 4} during a PWR severe accident

    SciTech Connect

    Reymond-Laruinaz, S.; Doizi, D.; Boudon, V.; Ducros, G.

    2015-07-01

    After the Fukushima accident, it became essential to have a way to monitor in real time the evolution of a nuclear reactor during a severe accident, in order to react efficiently and minimize the industrial, ecological and health consequences of the accident. Among gaseous fission products, the tetroxide of ruthenium RuO{sub 4} is of prime importance since it has a significant radiological impact. Ruthenium is a low volatile fission product but in case of the rupture of the vessel lower head by the molten corium, the air entering into the vessel oxidizes Ru into gaseous RuO{sub 4}, which is not trapped by the Filtered Containment Venting Systems. To monitor the presence of RuO{sub 4} allows making a diagnosis of the core degradation and quantifying the release into the atmosphere. To determine the presence of RuO{sub 4}, FTIR spectrometry was selected. To study the feasibility of the monitoring, high-resolution IR measurements were realized at the French synchrotron facility SOLEIL on the infrared beam line AILES. Thereafter, theoretical calculations were done to simulate the FTIR spectrum to describe the specific IR fingerprint of the molecule for each isotope and based on its partial pressure in the air. (authors)

  19. Verification of Optimal Control Strategy Search Using a Simplest 3-D PWR Xenon Oscillation Simulator

    SciTech Connect

    Shimazu, Yoichiro

    2006-07-01

    Power spatial oscillations due to the transient xenon spatial distribution are well known as xenon oscillation in large PWRs. When the reactor size becomes larger than the current design, then even radial oscillations can be also divergent. Even if the radial oscillation is convergent, when some control rods malfunction occurs, it is necessary to suppress the oscillation in as short time as possible. In such cases, optimal control strategy is required. Generally speaking the optimality search based on the modern control theory requires a lot of calculation for the evaluation of state variables. In the case of control rod malfunctions the xenon oscillation could be three dimensional. In such case, direct core calculations would be inevitable. From this point of view a very simple model, only four point reactor model, has been developed and verified. In this paper, an example of a procedure and the validity of the results for optimal control strategy search are presented by comparing it with the result by a three dimensional nuclear design code The simplest simulator can predict optimal strategy in less than 10 seconds on a PC. Thus it is recommended that a strategy generator, which is quick in analyzing and easy to use, might be installed in a monitoring system or in an operator guiding system. (author)

  20. Heat transfer to water from a vertical tube bundle under natural-circulation conditions. [PWR; BWR

    SciTech Connect

    Gruszczynski, M.J.; Viskanta, R.

    1983-01-01

    The natural circulation heat transfer data for longitudinal flow of water outside a vertical rod bundle are needed for developing correlations which can be used in best estimate computer codes to model thermal-hydraulic behavior of nuclear reactor cores under accident or shutdown conditions. The heat transfer coefficient between the fuel rod surface and the coolant is the key parameter required to predict the fuel temperature. Because of the absence of the required heat transfer coefficient data base under natural circulation conditions, experiments have been performed in a natural circulation loop. A seven-tube bundle having a pitch-to-diameter ratio of 1.25 was used as a test heat exchanger. A circulating flow was established in the loop, because of buoyancy differences between its two vertical legs. Steady-state and transient heat transfer measurements have been made over as wide a range of thermal conditions as possible with the system. Steady state heat transfer data were correlated in terms of relevant dimensionless parameters. Empirical correlations for the average Nusselt number, in terms of Reynolds number, Rayleigh number and the ratio of Grashof to Reynolds number are given.

  1. Uranium resource utilization improvements in the once-through PWR fuel cycle

    SciTech Connect

    Matzie, R A

    1980-04-01

    In support of the Nonproliferation Alternative Systems Assessment Program (NASAP), Combustion Engineering, Inc. performed a comprehensive analytical study of potential uranium utilization improvement options that can be backfit into existing PWRs operating on the once-through uranium fuel cycle. A large number of potential improvement options were examined as part of a preliminary survey of candidate options. The most attractive of these, from the standpoint of uranium utilization improvement, economic viability, and ease of implementation, were then selected for detailed analysis and were included in a single composite improvement case. This composite case represents an estimate of the total savings in U/sub 3/O/sub 8/ consumption that can be achieved in current-design PWRs by implementing improvements which can be developed and demonstrated in the near term. The improvement options which were evaluated in detail and included in the composite case were a new five-batch, extended-burnup fuel management scheme, low-leakage fuel management, modified lattice designs, axial blankets, reinsertion of initial core batches, and end-of-cycle stretchout.

  2. HYDRATE CORE DRILLING TESTS

    SciTech Connect

    John H. Cohen; Thomas E. Williams; Ali G. Kadaster; Bill V. Liddell

    2002-11-01

    The ''Methane Hydrate Production from Alaskan Permafrost'' project is a three-year endeavor being conducted by Maurer Technology Inc. (MTI), Noble, and Anadarko Petroleum, in partnership with the U.S. DOE National Energy Technology Laboratory (NETL). The project's goal is to build on previous and ongoing R&D in the area of onshore hydrate deposition. The project team plans to design and implement a program to safely and economically drill, core and produce gas from arctic hydrates. The current work scope includes drilling and coring one well on Anadarko leases in FY 2003 during the winter drilling season. A specially built on-site core analysis laboratory will be used to determine some of the physical characteristics of the hydrates and surrounding rock. Prior to going to the field, the project team designed and conducted a controlled series of coring tests for simulating coring of hydrate formations. A variety of equipment and procedures were tested and modified to develop a practical solution for this special application. This Topical Report summarizes these coring tests. A special facility was designed and installed at MTI's Drilling Research Center (DRC) in Houston and used to conduct coring tests. Equipment and procedures were tested by cutting cores from frozen mixtures of sand and water supported by casing and designed to simulate hydrate formations. Tests were conducted with chilled drilling fluids. Tests showed that frozen core can be washed out and reduced in size by the action of the drilling fluid. Washing of the core by the drilling fluid caused a reduction in core diameter, making core recovery very difficult (if not impossible). One successful solution was to drill the last 6 inches of core dry (without fluid circulation). These tests demonstrated that it will be difficult to capture core when drilling in permafrost or hydrates without implementing certain safeguards. Among the coring tests was a simulated hydrate formation comprised of coarse, large

  3. 23. CORE WORKER OPERATING A COREBLOWER THAT PNEUMATICALLY FILLED CORE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    23. CORE WORKER OPERATING A CORE-BLOWER THAT PNEUMATICALLY FILLED CORE BOXES WITH RESIGN IMPREGNATED SAND AND CREATED A CORE THAT THEN REQUIRED BAKING, CA. 1950. - Stockham Pipe & Fittings Company, 4000 Tenth Avenue North, Birmingham, Jefferson County, AL

  4. RELAP-7 Level 2 Milestone Report: Demonstration of a Steady State Single Phase PWR Simulation with RELAP-7

    SciTech Connect

    David Andrs; Ray Berry; Derek Gaston; Richard Martineau; John Peterson; Hongbin Zhang; Haihua Zhao; Ling Zou

    2012-05-01

    The document contains the simulation results of a steady state model PWR problem with the RELAP-7 code. The RELAP-7 code is the next generation nuclear reactor system safety analysis code being developed at Idaho National Laboratory (INL). The code is based on INL's modern scientific software development framework - MOOSE (Multi-Physics Object-Oriented Simulation Environment). This report summarizes the initial results of simulating a model steady-state single phase PWR problem using the current version of the RELAP-7 code. The major purpose of this demonstration simulation is to show that RELAP-7 code can be rapidly developed to simulate single-phase reactor problems. RELAP-7 is a new project started on October 1st, 2011. It will become the main reactor systems simulation toolkit for RISMC (Risk Informed Safety Margin Characterization) and the next generation tool in the RELAP reactor safety/systems analysis application series (the replacement for RELAP5). The key to the success of RELAP-7 is the simultaneous advancement of physical models, numerical methods, and software design while maintaining a solid user perspective. Physical models include both PDEs (Partial Differential Equations) and ODEs (Ordinary Differential Equations) and experimental based closure models. RELAP-7 will eventually utilize well posed governing equations for multiphase flow, which can be strictly verified. Closure models used in RELAP5 and newly developed models will be reviewed and selected to reflect the progress made during the past three decades. RELAP-7 uses modern numerical methods, which allow implicit time integration, higher order schemes in both time and space, and strongly coupled multi-physics simulations. RELAP-7 is written with object oriented programming language C++. Its development follows modern software design paradigms. The code is easy to read, develop, maintain, and couple with other codes. Most importantly, the modern software design allows the RELAP-7 code to

  5. Contribution of fuel vibrations to ex-core neutron noise during the first and second fuel cycles of the Sequoyah-1 pressurized water reactor

    SciTech Connect

    Sweeney, F.J.; March-Leuba, J.; Smith, C.M.

    1984-01-01

    Noise measurements were performed during the first and second fuel cycles of the Sequoyah-1 pressurized water reactor (PWR) to observe long-term changes in the ex-core neutron signatures. Increases in the ex-core neutron noise amplitude were observed throughout the 0.1- to 50.0-Hz range. In-core noise measurements indicate that fuel assembly vibrations contribute significantly to the ex-core neutron noise at nearly all frequencies in this range, probably due to mechanical or acoustic coupling with other vibrating internal structures. Space-dependent kinetics calculations show that ex-core neutron noise induced by fixed-amplitude fuel assembly vibrations will increase over a fuel cycle because of soluble boron and fuel concentration changes associated with burnup. These reactivity effects can also lead to 180/sup 0/ phase shifts between cross-core detectors. We concluded that it may be difficult to separate the changes in neutron noise due to attenuation (shielding) effects of structural vibrations from changes due to reactivity effects of fuel assembly motion on the basis of neutron noise amplitude or phase information. Amplitudes of core support barrel vibrations inferred from ex-core neutron noise measurements using calculated scale factors are likely to have a high degree of uncertainty, since these scale factors usually do not account for neutron noise generated by fuel assembly vibrations. Modifications in fuel management or design may also lead to altered neutron noise signature behavior over a fuel cycle.

  6. Graphical and tabular summaries of decay characteristics for once-through PWR, LMFBR, and FFTF fuel cycle materials. [Spent fuel, high-level waste fuel can scrap

    SciTech Connect

    Croff, A.G.; Liberman, M.S.; Morrison, G.W.

    1982-01-01

    Based on the results of ORIGEN2 and a newly developed code called ORMANG, graphical and summary tabular characteristics of spent fuel, high-level waste, and fuel assembly structural material (cladding) waste are presented for a generic pressurized-water reactor (PWR), a liquid-metal fast breeder reactor (LMFBR), and the Fast Flux Test Facility (FFTF). The characteristics include radioactivity, thermal power, and toxicity (water dilution volume). Given are graphs and summary tables containing characteristic totals and the principal nuclide contributors as well as graphs comparing the three reactors for a single material and the three materials for a single reactor.

  7. Evaluation of the thermal-hydraulic response and fuel rod thermal and mechanical deformation behavior during the power burst facility test LOC-3. [PWR

    SciTech Connect

    Yackle, T R; MacDonald, P E; Broughton, J M

    1980-01-01

    An evaluation of the results from the LOC-3 nuclear blowdown test conducted in the Power Burst Facility is presented. The test objective was to examine fuel and cladding behavior during a postulated cold leg break accident in a pressurized water reactor (PWR). Separate effects of rod internal pressure and the degree of irradiation were investigated in the four-rod test. Extensive cladding deformation (ballooning) and failure occurred during blowdown. The deformation of the low and high pressure rods was similar; however, the previously irradiated test rod deformed to a greater extent than a similar fresh rod exposed to identical system conditions.

  8. Optimization Study of Ultra-Long Cycle Fast Reactor Core Concept

    SciTech Connect

    Kim, T. K.; Tak, Taewoo; Lee, Deokjung; Hong, Ser Gi

    2014-11-01

    An optimization of an Ultra-long Cycle Fast Reactor (UCFR) design with a power rating of 1000 MW(electric), UCFR-1000, has been performed. Firstly, geometric optimization has been performed in the aspects of core size and core shape in terms of thermal–hydraulic (TH) feedback. Secondly, fuel composition optimization has been performed by adopting pressurized water reactor (PWR) spent fuel (SF) as a blanket material as well as natural uranium (NU). Thirdly, thorium has been loaded in the inner core for the optimization of radial power distribution. Lastly, a small-size UCFR with a power rate of 100 MWe has been developed with optimization of maximum neutron flux and fast neutron fluence limit for a short term deployable nuclear reactor. The equivalent diameter and the height of the optimized UCFR-1000 core are 5.9 and 2.4 m, respectively, while the equivalent diameter and the height of the optimized UCFR-100 core are 4.3 and 1.0 m, respectively. The size of the optimized UCFR-1000 has been enlarged in the radial direction and shortened in the axial direction from those of the initial UCFR design (Tak et al., 2013a) and this modification makes the burning speed of active core movement slower. It has been confirmed for both designs that a full-power operation of 60 years without refueling is feasible with respect to isotopics and criticality by a breed-and-burn strategy. The core performance characteristics of both designs have been evaluated in terms of axial/radial power shapes, neutron flux and nuclide distributions, breeding ratio, reactivity feedback coefficients, control rod worth, etc. By the design optimization study in this paper, the reductions of maximum neutron flux, fast neutron fluence, and axial/radial power peaking have been achieved, which are favorable for the safety of the UCFR.

  9. Rod consolidation of RG and E's (Rochester Gas and Electric Corporation) spent PWR (pressurized water reactor) fuel

    SciTech Connect

    Bailey, W.J.

    1987-05-01

    The rod consolidation demonstration involved pulling the fuel rods from five fuel assemblies from Unit 1 of RG and E's R.E. Ginna Nuclear Power Plant. Slow and careful rod pulling efforts were used for the first and second fuel assemblies. Rod pulling then proceeded smoothly and rapidly after some minor modifications were made to the UST and D consolidation equipment. The compaction ratios attained ranged from 1.85 to 2.00 (rods with collapsed cladding were replaced by dummy rods in one fuel assembly to demonstrate the 2:1 compaction ratio capability). This demonstration involved 895 PWR fuel rods, among which there were some known defective rods (over 50 had collapsed cladding); no rods were broken or dropped during the demonstration. However, one of the rods with collapsed cladding unexplainably broke during handling operations (i.e., reconfiguration in the failed fuel canister), subsequent to the rod consolidation demonstration. The broken rod created no facility problems; the pieces were encapsulated for subsequent storage. Another broken rod was found during postdemonstration cutting operations on the nonfuel-bearing structural components from the five assemblies; evidence indicates it was broken prior to any rod consolidation operations. During the demonstration, burnish-type lines or scratches were visible on the rods that were pulled; however, experience indicates that such lines are generally produced when rods are pulled (or pushed) through the spacer grids. Rods with collapsed cladding would not enter the funnel (the transition device between the fuel assembly and the canister that aids in obtaining high compaction ratios). Reforming of the flattened areas of the cladding on those rods was attempted to make the rod cross sections more nearly circular; some of the reformed rods passed through the funnel and into the canister.

  10. Computational Benchmark for Estimation of Reactivity Margin from Fission Products and Minor Actinides in PWR Burnup Credit

    SciTech Connect

    Wagner, J.C.

    2001-08-02

    This report proposes and documents a computational benchmark problem for the estimation of the additional reactivity margin available in spent nuclear fuel (SNF) from fission products and minor actinides in a burnup-credit storage/transport environment, relative to SNF compositions containing only the major actinides. The benchmark problem/configuration is a generic burnup credit cask designed to hold 32 pressurized water reactor (PWR) assemblies. The purpose of this computational benchmark is to provide a reference configuration for the estimation of the additional reactivity margin, which is encouraged in the U.S. Nuclear Regulatory Commission (NRC) guidance for partial burnup credit (ISG8), and document reference estimations of the additional reactivity margin as a function of initial enrichment, burnup, and cooling time. Consequently, the geometry and material specifications are provided in sufficient detail to enable independent evaluations. Estimates of additional reactivity margin for this reference configuration may be compared to those of similar burnup-credit casks to provide an indication of the validity of design-specific estimates of fission-product margin. The reference solutions were generated with the SAS2H-depletion and CSAS25-criticality sequences of the SCALE 4.4a package. Although the SAS2H and CSAS25 sequences have been extensively validated elsewhere, the reference solutions are not directly or indirectly based on experimental results. Consequently, this computational benchmark cannot be used to satisfy the ANS 8.1 requirements for validation of calculational methods and is not intended to be used to establish biases for burnup credit analyses.

  11. Core-Cutoff Tool

    NASA Technical Reports Server (NTRS)

    Gheen, Darrell

    2007-01-01

    A tool makes a cut perpendicular to the cylindrical axis of a core hole at a predetermined depth to free the core at that depth. The tool does not damage the surrounding material from which the core was cut, and it operates within the core-hole kerf. Coring usually begins with use of a hole saw or a hollow cylindrical abrasive cutting tool to make an annular hole that leaves the core (sometimes called the plug ) in place. In this approach to coring as practiced heretofore, the core is removed forcibly in a manner chosen to shear the core, preferably at or near the greatest depth of the core hole. Unfortunately, such forcible removal often damages both the core and the surrounding material (see Figure 1). In an alternative prior approach, especially applicable to toxic or fragile material, a core is formed and freed by means of milling operations that generate much material waste. In contrast, the present tool eliminates the damage associated with the hole-saw approach and reduces the extent of milling operations (and, hence, reduces the waste) associated with the milling approach. The present tool (see Figure 2) includes an inner sleeve and an outer sleeve and resembles the hollow cylindrical tool used to cut the core hole. The sleeves are thin enough that this tool fits within the kerf of the core hole. The inner sleeve is attached to a shaft that, in turn, can be attached to a drill motor or handle for turning the tool. This tool also includes a cutting wire attached to the distal ends of both sleeves. The cutting wire is long enough that with sufficient relative rotation of the inner and outer sleeves, the wire can cut all the way to the center of the core. The tool is inserted in the kerf until its distal end is seated at the full depth. The inner sleeve is then turned. During turning, frictional drag on the outer core pulls the cutting wire into contact with the core. The cutting force of the wire against the core increases with the tension in the wire and

  12. Isotopic validation for PWR actinide-only burnup credit using Yankee Rowe data

    SciTech Connect

    1997-11-01

    Safety analyses of criticality control systems for transportation packages include an assumption that the spent nuclear fuel (SNF) loaded into the package is fresh or unirradiated. In other words, the spent fuel is assumed to have its original, as-manufactured U-235 isotopic content. The ``fresh fuel`` assumption is very conservative since the potential reactivity of the nuclear fuel is substantially reduced after being irradiated in the reactor core. The concept of taking credit for this reduction in nuclear fuel reactivity due to burnup of the fuel, instead of using the fresh fuel assumption in the criticality safety analysis, is referred to as ``Burnup Credit.`` Burnup credit uses the actual physical composition of the fuel and accounts for the net reduction of fissile material and the buildup of neutron absorbers in the fuel as it is irradiated. Neutron absorbers include actinides and other isotopes generated as a result of the fission process. Using only the change in actinide isotopes in the burnup credit criticality analysis is referred to as ``Actinide-Only Burnup Credit.`` The use of burnup credit in the design of criticality control systems enables more spent fuel to be placed in a package. Increased package capacity results in a reduced number of storage, shipping and disposal containers for a given number of SNF assemblies. Fewer shipments result in a lower risk of accidents associated with the handling and transportation of spent fuel, thus reducing both radiological and nonradiological risk to the public. This paper describes the modeling and the results of comparison between measured and calculated isotopic inventories for a selected number of samples taken from a Yankee Rowe spent fuel assembly.

  13. Core sample extractor

    NASA Technical Reports Server (NTRS)

    Akins, James; Cobb, Billy; Hart, Steve; Leaptrotte, Jeff; Milhollin, James; Pernik, Mark

    1989-01-01

    The problem of retrieving and storing core samples from a hole drilled on the lunar surface is addressed. The total depth of the hole in question is 50 meters with a maximum diameter of 100 millimeters. The core sample itself has a diameter of 60 millimeters and will be two meters in length. It is therefore necessary to retrieve and store 25 core samples per hole. The design utilizes a control system that will stop the mechanism at a certain depth, a cam-linkage system that will fracture the core, and a storage system that will save and catalogue the cores to be extracted. The Rod Changer and Storage Design Group will provide the necessary tooling to get into the hole as well as to the core. The mechanical design for the cam-linkage system as well as the conceptual design of the storage device are described.

  14. The core paradox.

    NASA Technical Reports Server (NTRS)

    Kennedy, G. C.; Higgins, G. H.

    1973-01-01

    Rebuttal of suggestions from various critics attempting to provide an escape from the seeming paradox originated by Higgins and Kennedy's (1971) proposed possibility that the liquid in the outer core was thermally stably stratified and that this stratification might prove a powerful inhibitor to circulation of the outer core fluid of the kind postulated for the generation of the earth's magnetic field. These suggestions are examined and shown to provide no reasonable escape from the core paradox.

  15. The core paradox.

    NASA Technical Reports Server (NTRS)

    Kennedy, G. C.; Higgins, G. H.

    1973-01-01

    Rebuttal of suggestions from various critics attempting to provide an escape from the seeming paradox originated by Higgins and Kennedy's (1971) proposed possibility that the liquid in the outer core was thermally stably stratified and that this stratification might prove a powerful inhibitor to circulation of the outer core fluid of the kind postulated for the generation of the earth's magnetic field. These suggestions are examined and shown to provide no reasonable escape from the core paradox.

  16. Core Research Center

    USGS Publications Warehouse

    Hicks, Joshua; Adrian, Betty

    2009-01-01

    The Core Research Center (CRC) of the U.S. Geological Survey (USGS), located at the Denver Federal Center in Lakewood, Colo., currently houses rock core from more than 8,500 boreholes representing about 1.7 million feet of rock core from 35 States and cuttings from 54,000 boreholes representing 238 million feet of drilling in 28 States. Although most of the boreholes are located in the Rocky Mountain region, the geologic and geographic diversity of samples have helped the CRC become one of the largest and most heavily used public core repositories in the United States. Many of the boreholes represented in the collection were drilled for energy and mineral exploration, and many of the cores and cuttings were donated to the CRC by private companies in these industries. Some cores and cuttings were collected by the USGS along with other government agencies. Approximately one-half of the cores are slabbed and photographed. More than 18,000 thin sections and a large volume of analytical data from the cores and cuttings are also accessible. A growing collection of digital images of the cores are also becoming available on the CRC Web site Internet http://geology.cr.usgs.gov/crc/.

  17. Adaptive core simulation

    NASA Astrophysics Data System (ADS)

    Abdel-Khalik, Hany Samy

    The work presented in this thesis is a continuation of a master's thesis research project conducted by the author to gain insight into the applicability of inverse methods to developing adaptive simulation capabilities for core physics problems. Use of adaptive simulation is intended to improve the fidelity and robustness of important core attributes predictions such as core power distribution, thermal margins and core reactivity. Adaptive simulation utilizes a selected set of past and current reactor measurements of reactor observables, i.e. in-core instrumentations readings, to adapt the simulation in a meaningful way. A meaningful adaption will result in high fidelity and robust adapted core simulators models. To perform adaption, we propose an inverse theory approach in which the multitudes of input data to core simulators, i.e. reactor physics and thermal-hydraulic data, are to be adjusted to improve agreement with measured observables while keeping core simulators models unadapted. At a first glance, devising such adaption for typical core simulators models would render the approach impractical. This follows, since core simulators are based on very demanding computational models, i.e. based on complex physics models with millions of input data and output observables. This would spawn not only several prohibitive challenges but also numerous disparaging concerns. The challenges include the computational burdens of the sensitivity-type calculations required to construct Jacobian operators for the core simulators models. Also, the computational burdens of the uncertainty-type calculations required to estimate the uncertainty information of core simulators input data presents a demanding challenge. The concerns however are mainly related to the reliability of the adjusted input data. We demonstrate that the power of our proposed approach is mainly driven by taking advantage of this unfavorable situation. Our contribution begins with the realization that to obtain

  18. Can Psychiatric Rehabilitation Be Core to CORE?

    ERIC Educational Resources Information Center

    Olney, Marjorie F.; Gill, Kenneth J.

    2016-01-01

    Purpose: In this article, we seek to determine whether psychiatric rehabilitation principles and practices have been more fully incorporated into the Council on Rehabilitation Education (CORE) standards, the extent to which they are covered in four rehabilitation counseling "foundations" textbooks, and how they are reflected in the…

  19. Can Psychiatric Rehabilitation Be Core to CORE?

    ERIC Educational Resources Information Center

    Olney, Marjorie F.; Gill, Kenneth J.

    2016-01-01

    Purpose: In this article, we seek to determine whether psychiatric rehabilitation principles and practices have been more fully incorporated into the Council on Rehabilitation Education (CORE) standards, the extent to which they are covered in four rehabilitation counseling "foundations" textbooks, and how they are reflected in the…

  20. In-situ measurement of the effect of LiOH on the stability of fuel cladding oxide film in simulated PWR primary water environment

    SciTech Connect

    Saario, T.; Taehtinen, S.; Piippo, J.; Kukkonen, J.J.V.

    1995-12-31

    Development of new improved fuel cladding materials is a long process, partly because of the lack of fast and reliable in-situ techniques for investigations of cladding degradation in high temperature water environments. This paper describes results gained with the Contact Electric Resistance (CER) technique on the electric resistance of oxides growing on zirconium based fuel cladding materials. LiOH decreased the electric resistance of the oxides when about 70 ppm was injected in PWR water at 300 C. When PWR water contains boric acid and LiOH from the beginning of the exposure the fuel cladding material is covered by a hydroxide layer that protects the amorphous oxide layer and later hinders the increase of the resistance of the crystalline oxide layer. The dependency of electric resistance of the oxides on LiOH concentration is shown to correlate inversely with the effect of LiOH on weight gain. The kinetics of the breakdown process of electric resistance indicate that a phase transformation rather than a diffusion limited process is the mechanism of degradation. The growth rate of the electric resistance of the oxide in the early stage of oxide formation is shown to correlate well with the in-reactor weight gain of similar alloys. In-situ monitoring of the electric resistance of the oxide during growth is shown to give the same ranking order as long term in-reactor weight gain tests, but in a fraction of the testing time needed for weight gain tests.

  1. More on the Core

    ERIC Educational Resources Information Center

    Chan, Monnica

    2013-01-01

    From a higher education perspective, new "Common Core" standards could improve student college-readiness levels, reduce institutional remediation rates, and close education gaps in and between states. As a national initiative to create common educational standards for students across multiple states, the Common Core State Standards…

  2. Mercury's core evolution

    NASA Astrophysics Data System (ADS)

    Deproost, Marie-Hélène; Rivoldini, Attilio; Van Hoolst, Tim

    2016-10-01

    Remote sensing data of Mercury's surface by MESSENGER indicate that Mercury formed under reducing conditions. As a consequence, silicon is likely the main light element in the core together with a possible small fraction of sulfur. Compared to sulfur, which does almost not partition into solid iron at Mercury's core conditions and strongly decreases the melting temperature, silicon partitions almost equally well between solid and liquid iron and is not very effective at reducing the melting temperature of iron. Silicon as the major light element constituent instead of sulfur therefore implies a significantly higher core liquidus temperature and a decrease in the vigor of compositional convection generated by the release of light elements upon inner core formation.Due to the immiscibility in liquid Fe-Si-S at low pressure (below 15 GPa), the core might also not be homogeneous and consist of an inner S-poor Fe-Si core below a thinner Si-poor Fe-S layer. Here, we study the consequences of a silicon-rich core and the effect of the blanketing Fe-S layer on the thermal evolution of Mercury's core and on the generation of a magnetic field.

  3. Making an Ice Core.

    ERIC Educational Resources Information Center

    Kopaska-Merkel, David C.

    1995-01-01

    Explains an activity in which students construct a simulated ice core. Materials required include only a freezer, food coloring, a bottle, and water. This hands-on exercise demonstrates how a glacier is formed, how ice cores are studied, and the nature of precision and accuracy in measurement. Suitable for grades three through eight. (Author/PVD)

  4. Ice Core Investigations

    ERIC Educational Resources Information Center

    Krim, Jessica; Brody, Michael

    2008-01-01

    What can glaciers tell us about volcanoes and atmospheric conditions? How does this information relate to our understanding of climate change? Ice Core Investigations is an original and innovative activity that explores these types of questions. It brings together popular science issues such as research, climate change, ice core drilling, and air…

  5. NFE Core Bibliographies.

    ERIC Educational Resources Information Center

    Michigan State Univ., East Lansing. Inst. for International Studies in Education.

    This collection of core bibliographies, which expands on an initial bibliography published in 1979 of the core resources housed in the Non-Formal Education Information Center at Michigan State University, comprises a basic stock of materials on nonformal education and women in development that have been contributed by development planners,…

  6. Ice Core Investigations

    ERIC Educational Resources Information Center

    Krim, Jessica; Brody, Michael

    2008-01-01

    What can glaciers tell us about volcanoes and atmospheric conditions? How does this information relate to our understanding of climate change? Ice Core Investigations is an original and innovative activity that explores these types of questions. It brings together popular science issues such as research, climate change, ice core drilling, and air…

  7. More on the Core

    ERIC Educational Resources Information Center

    Chan, Monnica

    2013-01-01

    From a higher education perspective, new "Common Core" standards could improve student college-readiness levels, reduce institutional remediation rates, and close education gaps in and between states. As a national initiative to create common educational standards for students across multiple states, the Common Core State Standards…

  8. CORE - Performance Feedback System

    SciTech Connect

    2009-10-02

    CORE is an architecture to bridge the gaps between disparate data integration and delivery of disparate information visualization. The CORE Technology Program includes a suite of tools and user-centered staff that can facilitate rapid delivery of a deployable integrated information to users.

  9. Modular core holder

    SciTech Connect

    Mueller, J.; Cole, C.W.; Hamid, S.; Lucas, J.K.

    1991-03-05

    This patent describes a modular core holder. It comprises: a sleeve, forming an internal cavity for receiving a core. The sleeve including segments; support means, overlying the sleeve, for supporting the sleeve; and access means, positioned between at least two of the segments of the sleeve, for allowing measurement of conditions within the internal cavity.

  10. Making an Ice Core.

    ERIC Educational Resources Information Center

    Kopaska-Merkel, David C.

    1995-01-01

    Explains an activity in which students construct a simulated ice core. Materials required include only a freezer, food coloring, a bottle, and water. This hands-on exercise demonstrates how a glacier is formed, how ice cores are studied, and the nature of precision and accuracy in measurement. Suitable for grades three through eight. (Author/PVD)

  11. Iowa Core Annual Report

    ERIC Educational Resources Information Center

    Iowa Department of Education, 2015

    2015-01-01

    One central component of a great school system is a clear set of expectations, or standards, that educators help all students reach. In Iowa, that effort is known as the Iowa Core. The Iowa Core represents the statewide academic standards, which describe what students should know and be able to do in math, science, English language arts, and…

  12. Mars' core and magnetism.

    PubMed

    Stevenson, D J

    2001-07-12

    The detection of strongly magnetized ancient crust on Mars is one of the most surprising outcomes of recent Mars exploration, and provides important insight about the history and nature of the martian core. The iron-rich core probably formed during the hot accretion of Mars approximately 4.5 billion years ago and subsequently cooled at a rate dictated by the overlying mantle. A core dynamo operated much like Earth's current dynamo, but was probably limited in duration to several hundred million years. The early demise of the dynamo could have arisen through a change in the cooling rate of the mantle, or even a switch in convective style that led to mantle heating. Presently, Mars probably has a liquid, conductive outer core and might have a solid inner core like Earth.

  13. Lunar Core and Tides

    NASA Technical Reports Server (NTRS)

    Williams, J. G.; Boggs, D. H.; Ratcliff, J. T.

    2004-01-01

    Variations in rotation and orientation of the Moon are sensitive to solid-body tidal dissipation, dissipation due to relative motion at the fluid-core/solid-mantle boundary, and tidal Love number k2 [1,2]. There is weaker sensitivity to flattening of the core-mantle boundary (CMB) [2,3,4] and fluid core moment of inertia [1]. Accurate Lunar Laser Ranging (LLR) measurements of the distance from observatories on the Earth to four retroreflector arrays on the Moon are sensitive to lunar rotation and orientation variations and tidal displacements. Past solutions using the LLR data have given results for dissipation due to solid-body tides and fluid core [1] plus Love number [1-5]. Detection of CMB flattening, which in the past has been marginal but improving [3,4,5], now seems significant. Direct detection of the core moment has not yet been achieved.

  14. Internal core tightener

    DOEpatents

    Brynsvold, Glen V.; Snyder, Jr., Harold J.

    1976-06-22

    An internal core tightener which is a linear actuated (vertical actuation motion) expanding device utilizing a minimum of moving parts to perform the lateral tightening function. The key features are: (1) large contact areas to transmit loads during reactor operation; (2) actuation cam surfaces loaded only during clamping and unclamping operation; (3) separation of the parts and internal operation involved in the holding function from those involved in the actuation function; and (4) preloaded pads with compliant travel at each face of the hexagonal assembly at the two clamping planes to accommodate thermal expansion and irradiation induced swelling. The latter feature enables use of a "fixed" outer core boundary, and thus eliminates the uncertainty in gross core dimensions, and potential for rapid core reactivity changes as a result of core dimensional change.

  15. Lunar Core and Tides

    NASA Technical Reports Server (NTRS)

    Williams, J. G.; Boggs, D. H.; Ratcliff, J. T.

    2004-01-01

    Variations in rotation and orientation of the Moon are sensitive to solid-body tidal dissipation, dissipation due to relative motion at the fluid-core/solid-mantle boundary, and tidal Love number k2 [1,2]. There is weaker sensitivity to flattening of the core-mantle boundary (CMB) [2,3,4] and fluid core moment of inertia [1]. Accurate Lunar Laser Ranging (LLR) measurements of the distance from observatories on the Earth to four retroreflector arrays on the Moon are sensitive to lunar rotation and orientation variations and tidal displacements. Past solutions using the LLR data have given results for dissipation due to solid-body tides and fluid core [1] plus Love number [1-5]. Detection of CMB flattening, which in the past has been marginal but improving [3,4,5], now seems significant. Direct detection of the core moment has not yet been achieved.

  16. Comparison of BR3 surveillance and vessel plates to the surrogate plates representative of the Yankee Rowe PWR vessel

    SciTech Connect

    Fabry, A.; Chaouadi, R.; Puzzolante, J.L.; Van de Velde, J.; Biemiller, E.C.; Rosinski, S.T.; Carter, R.G.

    1999-10-01

    The sister pressure vessels at the BR3 and Yankee Rowe PWR plants were operated at lower-than-usual temperature ({approx}260 C) and their plates were austenitized at higher-than-usual temperature ({approx}970 C) -- a heat treatment leading to a coarser microstructure than is typical for the fine grain plates considered in development of USNRC Regulatory Guide 1.99. The surveillance programs provided by Westinghouse for the two plants were limited to the same A302-B plate representative of the Rowe vessel upper shell plate; this material displayed outlier behavior characterized by a 41J. Charpy-V Notch shift significantly larger than predicted by Regulatory Guide 1.99. Because lower irradiation temperature and nickel alloying are generally considered detrimental to irradiation sensitivity, there was a major concern that the nickel-modified lower Rowe plate and the nickel-modified BR3 plate may become too embrittled to satisfy the toughness requirements embodied in the PTS screening criterion. This paper compares three complementary studies undertaken to clarify these uncertainties: (1) The accelerated irradiation and test program launched in 1990 by Yankee Atomic Electric Company using typical vessel plate materials containing 0.24% copper at two nickel levels: YA1, 0.63% (A533-B) and YA9, 0.19% (A302-B). These were heat-treated to produce the coarse and fine grain microstructures representative of the Yankee/BR3 and the Regulatory Guide plates, respectively; (2) The BR3 surveillance and vessel testing program; this vessel was wet-annealed in 1984, relicensed for operation till the plant shutdown in 1987, and was trepanned in early 1995; (3) The accelerated irradiations in the Belgian test reactor BR2 of the Yankee coarse grain plates YA1 and YA9 together with BR3 vessel specimens extracted at nozzle elevation, a location with negligible radiation exposure. It is contended that the PTS screening criterion was never attained by the BR3 and Rowe plates, and that the

  17. 34. DESPATCH CORE OVENS, GREY IRON FOUNDRY CORE ROOM, BAKES ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    34. DESPATCH CORE OVENS, GREY IRON FOUNDRY CORE ROOM, BAKES CORES THAT ARE NOT MADE ON HEATED OR COLD BOX CORE MACHINES, TO SET BINDING AGENTS MIXED WITH THE SAND CREATING CORES HARD ENOUGH TO WITHSTAND THE FLOW OF MOLTEN IRON INSIDE A MOLD. - Stockham Pipe & Fittings Company, Grey Iron Foundry, 4000 Tenth Avenue North, Birmingham, Jefferson County, AL

  18. Multiple Core Galaxies

    NASA Technical Reports Server (NTRS)

    Miller, R.H.; Morrison, David (Technical Monitor)

    1994-01-01

    Nuclei of galaxies often show complicated density structures and perplexing kinematic signatures. In the past we have reported numerical experiments indicating a natural tendency for galaxies to show nuclei offset with respect to nearby isophotes and for the nucleus to have a radial velocity different from the galaxy's systemic velocity. Other experiments show normal mode oscillations in galaxies with large amplitudes. These oscillations do not damp appreciably over a Hubble time. The common thread running through all these is that galaxies often show evidence of ringing, bouncing, or sloshing around in unexpected ways, even though they have not been disturbed by any external event. Recent observational evidence shows yet another phenomenon indicating the dynamical complexity of central regions of galaxies: multiple cores (M31, Markarian 315 and 463 for example). These systems can hardly be static. We noted long-lived multiple core systems in galaxies in numerical experiments some years ago, and we have more recently followed up with a series of experiments on multiple core galaxies, starting with two cores. The relevant parameters are the energy in the orbiting clumps, their relative.masses, the (local) strength of the potential well representing the parent galaxy, and the number of cores. We have studied the dependence of the merger rates and the nature of the final merger product on these parameters. Individual cores survive much longer in stronger background potentials. Cores can survive for a substantial fraction of a Hubble time if they travel on reasonable orbits.

  19. Multiple Core Galaxies

    NASA Technical Reports Server (NTRS)

    Miller, R.H.; Morrison, David (Technical Monitor)

    1994-01-01

    Nuclei of galaxies often show complicated density structures and perplexing kinematic signatures. In the past we have reported numerical experiments indicating a natural tendency for galaxies to show nuclei offset with respect to nearby isophotes and for the nucleus to have a radial velocity different from the galaxy's systemic velocity. Other experiments show normal mode oscillations in galaxies with large amplitudes. These oscillations do not damp appreciably over a Hubble time. The common thread running through all these is that galaxies often show evidence of ringing, bouncing, or sloshing around in unexpected ways, even though they have not been disturbed by any external event. Recent observational evidence shows yet another phenomenon indicating the dynamical complexity of central regions of galaxies: multiple cores (M31, Markarian 315 and 463 for example). These systems can hardly be static. We noted long-lived multiple core systems in galaxies in numerical experiments some years ago, and we have more recently followed up with a series of experiments on multiple core galaxies, starting with two cores. The relevant parameters are the energy in the orbiting clumps, their relative.masses, the (local) strength of the potential well representing the parent galaxy, and the number of cores. We have studied the dependence of the merger rates and the nature of the final merger product on these parameters. Individual cores survive much longer in stronger background potentials. Cores can survive for a substantial fraction of a Hubble time if they travel on reasonable orbits.

  20. Global Core Plasma Model

    NASA Technical Reports Server (NTRS)

    Gallagher, Dennis L.; Craven, P. D.; Comfort, R. H.

    1999-01-01

    Abstract. The Global Core Plasma Model (GCPM) provides, empirically derived, core plasma density as a function of geomagnetic and solar conditions throughout the inner magnetosphere. It is continuous in value and gradient and is composed of separate models for the ionosphere, the plasmasphere, the plasmapause, the trough, and the polar cap. The relative composition of plasmaspheric H+, He+, and O+ is included in the GCPM. A blunt plasmaspheric bulge and rotation of the bulge with changing geomagnetic conditions is included. The GCPM is an amalgam of density models, intended to serve as a framework for continued improvement as new measurements become available and are used to characterize core plasma density, composition, and temperature.

  1. Global Core Plasma Model

    NASA Technical Reports Server (NTRS)

    Gallagher, Dennis L.; Craven, P. D.; Comfort, R. H.

    1999-01-01

    Abstract. The Global Core Plasma Model (GCPM) provides, empirically derived, core plasma density as a function of geomagnetic and solar conditions throughout the inner magnetosphere. It is continuous in value and gradient and is composed of separate models for the ionosphere, the plasmasphere, the plasmapause, the trough, and the polar cap. The relative composition of plasmaspheric H+, He+, and O+ is included in the GCPM. A blunt plasmaspheric bulge and rotation of the bulge with changing geomagnetic conditions is included. The GCPM is an amalgam of density models, intended to serve as a framework for continued improvement as new measurements become available and are used to characterize core plasma density, composition, and temperature.

  2. Core shroud corner joints

    DOEpatents

    Gilmore, Charles B.; Forsyth, David R.

    2013-09-10

    A core shroud is provided, which includes a number of planar members, a number of unitary corners, and a number of subassemblies each comprising a combination of the planar members and the unitary corners. Each unitary corner comprises a unitary extrusion including a first planar portion and a second planar portion disposed perpendicularly with respect to the first planar portion. At least one of the subassemblies comprises a plurality of the unitary corners disposed side-by-side in an alternating opposing relationship. A plurality of the subassemblies can be combined to form a quarter perimeter segment of the core shroud. Four quarter perimeter segments join together to form the core shroud.

  3. Severe accident thermal analyses of a PWR with in-vessel radiation/convection and external flooding

    SciTech Connect

    Hawkes, G.L.; O`Brien, J.E.

    1992-08-01

    A severe accident thermal analysis has been performed to study the effect of thermal radiation from the upper surface of a relocated molten core to the vessel inner walls and vessel internals. External water flooding has been included as a means of cooling the vessel to prevent thermal failure. A finite element gray body radiation model is used to predict radiant heat transfer from the molten core to the vessel wall, core barrel, reflector shield, and fuel assemblies of a partially melted and partially relocated core with decay heat. Parametric studies have been performed in which variations in the emissivity of the core crust, vessel wall, fuel assemblies, and other vessel internals have been considered. Other parameters considered included the flooding water level, and vessel upper structure radiant temperature. A finite element computational fluid dynamics model of hydrogen turbulent natural convection inside the vessel is included. The effect of a metallic layer overlying the relocated ceramic core has also been considered. Inside vessel wall temperatures were predicted to be excess of the melting point for some cases. These studies show that vessel integrity is mainly dependent upon the height of the flooding water on the vessel exterior.

  4. Severe accident thermal analyses of a PWR with in-vessel radiation/convection and external flooding

    SciTech Connect

    Hawkes, G.L.; O'Brien, J.E.

    1992-01-01

    A severe accident thermal analysis has been performed to study the effect of thermal radiation from the upper surface of a relocated molten core to the vessel inner walls and vessel internals. External water flooding has been included as a means of cooling the vessel to prevent thermal failure. A finite element gray body radiation model is used to predict radiant heat transfer from the molten core to the vessel wall, core barrel, reflector shield, and fuel assemblies of a partially melted and partially relocated core with decay heat. Parametric studies have been performed in which variations in the emissivity of the core crust, vessel wall, fuel assemblies, and other vessel internals have been considered. Other parameters considered included the flooding water level, and vessel upper structure radiant temperature. A finite element computational fluid dynamics model of hydrogen turbulent natural convection inside the vessel is included. The effect of a metallic layer overlying the relocated ceramic core has also been considered. Inside vessel wall temperatures were predicted to be excess of the melting point for some cases. These studies show that vessel integrity is mainly dependent upon the height of the flooding water on the vessel exterior.

  5. Qualification of CASMO5 / SIMULATE-3K against the SPERT-III E-core cold start-up experiments

    SciTech Connect

    Grandi, G.; Moberg, L.

    2012-07-01

    SIMULATE-3K is a three-dimensional kinetic code applicable to LWR Reactivity Initiated Accidents. S3K has been used to calculate several international recognized benchmarks. However, the feedback models in the benchmark exercises are different from the feedback models that SIMULATE-3K uses for LWR reactors. For this reason, it is worth comparing the SIMULATE-3K capabilities for Reactivity Initiated Accidents against kinetic experiments. The Special Power Excursion Reactor Test III was a pressurized-water, nuclear-research facility constructed to analyze the reactor kinetic behavior under initial conditions similar to those of commercial LWRs. The SPERT III E-core resembles a PWR in terms of fuel type, moderator, coolant flow rate, and system pressure. The initial test conditions (power, core flow, system pressure, core inlet temperature) are representative of cold start-up, hot start-up, hot standby, and hot full power. The qualification of S3K against the SPERT III E-core measurements is an ongoing work at Studsvik. In this paper, the results for the 30 cold start-up tests are presented. The results show good agreement with the experiments for the reactivity initiated accident main parameters: peak power, energy release and compensated reactivity. Predicted and measured peak powers differ at most by 13%. Measured and predicted reactivity compensations at the time of the peak power differ less than 0.01 $. Predicted and measured energy release differ at most by 13%. All differences are within the experimental uncertainty. (authors)

  6. A Critical Review of Practice of Equating the Reactivity of Spent Fuel to Fresh Fuel in Burnup Credit Criticality Safety Analyses for PWR Spent Fuel Pool Storage

    SciTech Connect

    Wagner, J.C.; Parks, C.V.

    2000-09-01

    This research examines the practice of equating the reactivity of spent fuel to that of fresh fuel for the purpose of performing burnup credit criticality safety analyses for PWR spent fuel pool (SFP) storage conditions. The investigation consists of comparing k{sub inf} estimates based on reactivity equivalent fresh fuel enrichment (REFFE) to k{sub inf} estimates using the actual spent fuel isotopics. Analyses of selected storage configurations common in PWR SFPs show that this practice yields nonconservative results (on the order of a few tenths of a percent) in configurations in which the spent fuel is adjacent to higher-reactivity assemblies (e.g., fresh or lower-burned assemblies) and yields conservative results in configurations in which spent fuel is adjacent to lower-reactivity assemblies (e.g., higher-burned fuel or empty cells). When the REFFE is determined based on unborated water moderation, analyses for storage conditions with soluble boron present reveal significant nonconservative results associated with the use of the REFFE. This observation is considered to be important, especially considering the recent allowance of credit for soluble boron up to 5% in reactivity. Finally, it is shown that the practice of equating the reactivity of spent fuel to fresh fuel is acceptable, provided the conditions for which the REFFE was determined remain unchanged. Determination of the REFFE for a reference configuration and subsequent use of the REFFE for different configurations violates the basis used for the determination of the REFFE and, thus, may lead to inaccurate, and possibly, nonconservative estimates of reactivity. A significant concentration ({approximately}2000 ppm) of soluble boron is typically (but not necessarily required to be) present in PWR SFPs, of which only a portion ({le} 500 ppm) may be credited in safety analyses. Thus, a large subcritical margin currently exists that more than accounts for errors or uncertainties associated with the use of

  7. Magnetorotational iron core collapse

    NASA Technical Reports Server (NTRS)

    Symbalisty, E. M. D.

    1984-01-01

    During its final evolutionary stages, a massive star, as considered in current astrophysical theory, undergoes rapid collapse, thereby triggering a sequence of a catastrophic event which results in a Type II supernova explosion. A remnant neutron star or a black hole is left after the explosion. Stellar collapse occurs, when thermonuclear fusion has consumed the lighter elements present. At this stage, the core consists of iron. Difficulties arise regarding an appropriate model with respect to the core collapse. The present investigation is concerned with the evolution of a Type II supernova core including the effects of rotation and magnetic fields. A simple neutrino model is developed which reproduced the spherically symmetric results of Bowers and Wilson (1982). Several two-dimensional computational models of stellar collapse are studied, taking into account a case in which a 15 solar masses iron core was artificially given rotational and magnetic energy.

  8. Biospecimen Core Resource - TCGA

    Cancer.gov

    The Cancer Genome Atlas (TCGA) Biospecimen Core Resource centralized laboratory reviews and processes blood and tissue samples and their associated data using optimized standard operating procedures for the entire TCGA Research Network.

  9. Contaminated Sediment Core Profiling

    EPA Science Inventory

    Evaluating the environmental risk of sites containing contaminated sediments often poses major challenges due in part to the absence of detailed information available for a given location. Sediment core profiling is often utilized during preliminary environmental investigations ...

  10. INTEGRAL core programme

    NASA Technical Reports Server (NTRS)

    Gehrels, N.; Schoenfelder, V.; Ubertini, P.; Winkler, C.

    1997-01-01

    The International Gamma Ray Astrophysics Laboratory (INTEGRAL) mission is described with emphasis on the INTEGRAL core program. The progress made in the planning activities for the core program is reported on. The INTEGRAL mission has a nominal lifetime of two years with a five year extension option. The observing time will be divided between the core program (between 30 and 35 percent during the first two years) and general observations. The core program consists of three main elements: the deep survey of the Galactic plane in the central radian of the Galaxy; frequent scans of the Galactic plane in the search for transient sources, and pointed observations of several selected sources. The allocation of the observation time is detailed and the sensitivities of the observations are outlined.

  11. Core assembly storage structure

    DOEpatents

    Jones, Jr., Charles E.; Brunings, Jay E.

    1988-01-01

    A structure for the storage of core assemblies from a liquid metal-cooled nuclear reactor. The structure comprises an enclosed housing having a substantially flat horizontal top plate, a bottom plate and substantially vertical wall members extending therebetween. A plurality of thimble members extend downwardly through the top plate. Each thimble member is closed at its bottom end and has an open end adjacent said top plate. Each thimble member has a length and diameter greater than that of the core assembly to be stored therein. The housing is provided with an inlet duct for the admission of cooling air and an exhaust duct for the discharge of air therefrom, such that when hot core assemblies are placed in the thimbles, the heat generated will by convection cause air to flow from the inlet duct around the thimbles and out the exhaust duct maintaining the core assemblies at a safe temperature without the necessity of auxiliary powered cooling equipment.

  12. Contaminated Sediment Core Profiling

    EPA Science Inventory

    Evaluating the environmental risk of sites containing contaminated sediments often poses major challenges due in part to the absence of detailed information available for a given location. Sediment core profiling is often utilized during preliminary environmental investigations ...

  13. Warm core rings

    NASA Astrophysics Data System (ADS)

    Bell, Peter M.

    Gulf stream phenomena have been the focus of numerous studies by U.S. and Canadian oceanographic laboratories. Two years ago, observations of warm core rings associated with the Gulf Stream were reported in The Oceanography Report, (November 2, 1982, p. 834). It was noted then that the structure of warm core rings can undergo rapid transformation. Recently, a multidisciplinary group of physical and biological oceanographic institutions has examined the evolution of warm core rings in detail [Nature, 308, pp. 837-840, 1984]. The study has involved research vessels Endeavor, Atlantis II, and Albatross IV for surface measurements of temperature, salinity, and for measurement surface pigments to assess the concentration of marine plants. The results are that even though warm core rings are often very stable, undergoing only slow changes, it turns out that major alterations in structure can and do occur in short periods of 2-5 days.

  14. WIMS/PANTHER analysis of UO{sub 2}/MOX cores using embedded super-cells

    SciTech Connect

    Knight, M.; Bryce, P.; Hall, S.

    2012-07-01

    This paper describes a method of analysing PWR UO{sub 2}MOX cores with WIMS/PANTHER. Embedded super-cells, run within the reactor code, are used to correct the standard methodology of using 2-group smeared data from single assembly lattice calculations. In many other codes the weakness of this standard approach has been improved for MOX by imposing a more realistic environment in the lattice code, or by improving the sophistication of the reactor code. In this approach an intermediate set of calculations is introduced, leaving both lattice and reactor calculations broadly unchanged. The essence of the approach is that the whole core is broken down into a set of 'embedded' super-cells, each extending over just four quarter assemblies, with zero leakage imposed at the assembly mid-lines. Each supercell is solved twice, first with a detailed multi-group pin-by-pin solution, and then with the standard single assembly approach. Correction factors are defined by comparing the two solutions, and these can be applied in whole core calculations. The restriction that all such calculations are modelled with zero leakage means that they are independent of each other and of the core-wide flux shape. This allows parallel pre-calculation for the entire cycle once the loading pattern has been determined, in much the same way that single assembly lattice calculations can be pre-calculated once the range of fuel types is known. Comparisons against a whole core pin-by-pin reference demonstrates that the embedding process does not introduce a significant error, even after burnup and refuelling. Comparisons against a WIMS reference demonstrate that a pin-by-pin multi-group diffusion solution is capable of capturing the main interface effects. This therefore defines a practical approach for achieving results close to lattice code accuracy, but broadly at the cost of a standard reactor calculation. (authors)

  15. Core-Noise Research

    NASA Technical Reports Server (NTRS)

    Hultgren, Lennart S.

    2012-01-01

    This presentation is a technical summary of and outlook for NASA-internal and NASA-sponsored external research on core noise funded by the Fundamental Aeronautics Program Subsonic Fixed Wing (SFW) Project. Sections of the presentation cover: the SFW system-level noise metrics for the 2015 (N+1), 2020 (N+2), and 2025 (N+3) timeframes; SFW strategic thrusts and technical challenges; SFW advanced subsystems that are broadly applicable to N+3 vehicle concepts, with an indication where further noise research is needed; the components of core noise (compressor, combustor and turbine noise) and a rationale for NASA's current emphasis on the combustor-noise component; the increase in the relative importance of core noise due to turbofan design trends; the need to understand and mitigate core-noise sources for high-efficiency small gas generators; and the current research activities in the core-noise area, with additional details given about forthcoming updates to NASA's Aircraft Noise Prediction Program (ANOPP) core-noise prediction capabilities, two NRA efforts (Honeywell International, Phoenix, AZ and University of Illinois at Urbana-Champaign, respectively) to improve the understanding of core-noise sources and noise propagation through the engine core, and an effort to develop oxide/oxide ceramic-matrix-composite (CMC) liners for broadband noise attenuation suitable for turbofan-core application. Core noise must be addressed to ensure that the N+3 noise goals are met. Focused, but long-term, core-noise research is carried out to enable the advanced high-efficiency small gas-generator subsystem, common to several N+3 conceptual designs, needed to meet NASA's technical challenges. Intermediate updates to prediction tools are implemented as the understanding of the source structure and engine-internal propagation effects is improved. The NASA Fundamental Aeronautics Program has the principal objective of overcoming today's national challenges in air transportation. The

  16. Nuclear core positioning system

    DOEpatents

    Garkisch, Hans D.; Yant, Howard W.; Patterson, John F.

    1979-01-01

    A structural support system for the core of a nuclear reactor which achieves relatively restricted clearances at operating conditions and yet allows sufficient clearance between fuel assemblies at refueling temperatures. Axially displaced spacer pads having variable between pad spacing and a temperature compensated radial restraint system are utilized to maintain clearances between the fuel elements. The core support plates are constructed of metals specially chosen such that differential thermal expansion produces positive restraint at operating temperatures.

  17. Core bounce supernovae

    SciTech Connect

    Cooperstein, J.

    1987-01-01

    The gravitational collapse mechanism for Type II supernovae is considered, concentrating on the direct implosion - core bounce - hydrodynamic explosion picture. We examine the influence of the stiffness of the dense matter equation of state and discuss how the shock wave is formed. Its chances of success are determined by the equation of state, general relativistic effects, neutrino transport, and the size of presupernova iron core. 12 refs., 1 tab.

  18. SLS Core Stage Simulator

    NASA Image and Video Library

    2015-02-02

    CHRISTOPHER CRUMBLY, MANAGER OF THE SPACECRAFT PAYLOAD INTEGRATION AND EVOLUTION OFFICE, GAVE VISITORS AN INSIDER'S PERSPECTIVE ON THE CORE STAGE SIMULATOR AT MARSHALL AND ITS IMPORTANCE TO DEVELOPMENT OF THE SPACE LAUNCH SYSTEM. CHRISTOPHER CRUMBLY, MANAGER OF THE SPACECRAFT PAYLOAD INTEGRATION AND EVOLUTION OFFICE, GAVE VISITORS AN INSIDER'S PERSPECTIVE ON THE CORE STAGE SIMULATOR AT MARSHALL AND ITS IMPORTANCE TO DEVELOPMENT OF THE SPACE LAUNCH SYSTEM.

  19. Micro coring apparatus

    NASA Technical Reports Server (NTRS)

    Collins, David; Brooks, Marshall; Chen, Paul; Dwelle, Paul; Fischer, Ben

    1989-01-01

    A micro-coring apparatus for lunar exploration applications, that is compatible with the other components of the Walking Mobile Platform, was designed. The primary purpose of core sampling is to gain an understanding of the geological composition and properties of the prescribed environment. This procedure has been used extensively for Earth studies and in limited applications during lunar explorations. The corer is described and analyzed for effectiveness.

  20. Spectra of Hot Cores

    NASA Astrophysics Data System (ADS)

    Chakrabarti, S.; McKee, C. F.

    2003-12-01

    The turbulent core model for massive star formation (McKee & Tan 2002) generalizes the standard isothermal collapse model for low-mass stars to include turbulent pressure support. This model predicts reasonable massive star formation times of order 105 years, which is short enough to overcome the radiation pressure of the newly formed star. We calculate the millimeter and infrared spectrum predicted by the turbulent core model and compare with observations of several hot molecular cores. We consider spherically symmetric dust envelopes and use DUSTY, a 1-D radiative transfer code (Ivezic, Nenkova, Elitzur 1997), to numerically calculate the SEDs of these hot cores. We also analytically calculate the spectra in the asymptotic regions of low and high frequency and join these asymptotic forms smoothly by a fitting function that minimizes the relative error between the analytic and numerical spectra. Thus, we are able to express the functional dependence of the spectra of hot cores in terms of the dynamical variables of any given collapse model. This approach allows us to use observed SEDs as a diagnostic tool in inferring physical conditions in these cores.

  1. MCNP LWR Core Generator

    SciTech Connect

    Fischer, Noah A.

    2012-08-14

    The reactor core input generator allows for MCNP input files to be tailored to design specifications and generated in seconds. Full reactor models can now easily be created by specifying a small set of parameters and generating an MCNP input for a full reactor core. Axial zoning of the core will allow for density variation in the fuel and moderator, with pin-by-pin fidelity, so that BWR cores can more accurately be modeled. LWR core work in progress: (1) Reflectivity option for specifying 1/4, 1/2, or full core simulation; (2) Axial zoning for moderator densities that vary with height; (3) Generating multiple types of assemblies for different fuel enrichments; and (4) Parameters for specifying BWR box walls. Fuel pin work in progress: (1) Radial and azimuthal zoning for generating further unique materials in fuel rods; (2) Options for specifying different types of fuel for MOX or multiple burn assemblies; (3) Additional options for replacing fuel rods with burnable poison rods; and (4) Control rod/blade modeling.

  2. Emergency core cooling system

    DOEpatents

    Schenewerk, William E.; Glasgow, Lyle E.

    1983-01-01

    A liquid metal cooled fast breeder reactor provided with an emergency core cooling system includes a reactor vessel which contains a reactor core comprising an array of fuel assemblies and a plurality of blanket assemblies. The reactor core is immersed in a pool of liquid metal coolant. The reactor also includes a primary coolant system comprising a pump and conduits for circulating liquid metal coolant to the reactor core and through the fuel and blanket assemblies of the core. A converging-diverging venturi nozzle with an intermediate throat section is provided in between the assemblies and the pump. The intermediate throat section of the nozzle is provided with at least one opening which is in fluid communication with the pool of liquid sodium. In normal operation, coolant flows from the pump through the nozzle to the assemblies with very little fluid flowing through the opening in the throat. However, when the pump is not running, residual heat in the core causes fluid from the pool to flow through the opening in the throat of the nozzle and outwardly through the nozzle to the assemblies, thus providing a means of removing decay heat.

  3. Core-Noise

    NASA Technical Reports Server (NTRS)

    Hultgren, Lennart S.

    2010-01-01

    This presentation is a technical progress report and near-term outlook for NASA-internal and NASA-sponsored external work on core (combustor and turbine) noise funded by the Fundamental Aeronautics Program Subsonic Fixed Wing (SFW) Project. Sections of the presentation cover: the SFW system level noise metrics for the 2015, 2020, and 2025 timeframes; the emerging importance of core noise and its relevance to the SFW Reduced-Noise-Aircraft Technical Challenge; the current research activities in the core-noise area, with some additional details given about the development of a high-fidelity combustion-noise prediction capability; the need for a core-noise diagnostic capability to generate benchmark data for validation of both high-fidelity work and improved models, as well as testing of future noise-reduction technologies; relevant existing core-noise tests using real engines and auxiliary power units; and examples of possible scenarios for a future diagnostic facility. The NASA Fundamental Aeronautics Program has the principal objective of overcoming today's national challenges in air transportation. The SFW Reduced-Noise-Aircraft Technical Challenge aims to enable concepts and technologies to dramatically reduce the perceived aircraft noise outside of airport boundaries. This reduction of aircraft noise is critical for enabling the anticipated large increase in future air traffic. Noise generated in the jet engine core, by sources such as the compressor, combustor, and turbine, can be a significant contribution to the overall noise signature at low-power conditions, typical of approach flight. At high engine power during takeoff, jet and fan noise have traditionally dominated over core noise. However, current design trends and expected technological advances in engine-cycle design as well as noise-reduction methods are likely to reduce non-core noise even at engine-power points higher than approach. In addition, future low-emission combustor designs could increase

  4. Laser anemometry measurements of natural circulation flow in a scale model PWR reactor system. [Pressurized Water Reactor

    NASA Technical Reports Server (NTRS)

    Kadambi, J. R.; Schneider, S. J.; Stewart, W. A.

    1986-01-01

    The natural circulation of a single phase fluid in a scale model of a pressurized water reactor system during a postulated grade core accident is analyzed. The fluids utilized were water and SF6. The design of the reactor model and the similitude requirements are described. Four LDA tests were conducted: water with 28 kW of heat in the simulated core, with and without the participation of simulated steam generators; water with 28 kW of heat in the simulated core, with the participation of simulated steam generators and with cold upflow of 12 lbm/min from the lower plenum; and SF6 with 0.9 kW of heat in the simulated core and without the participation of the simulated steam generators. For the water tests, the velocity of the water in the center of the core increases with vertical height and continues to increase in the upper plenum. For SF6, it is observed that the velocities are an order of magnitude higher than those of water; however, the velocity patterns are similar.

  5. ATHOS: a computer program for thermal-hydraulic analysis of steam generators. Volume 1. Mathematical and physical models and method of solution. [PWR

    SciTech Connect

    Singhal, A.K.; Keeton, L.W.; Spalding, D.B.; Srikantiah, G.S.

    1982-10-01

    ATHOS (Analysis of the Thermal Hydraulics of Steam Generators) is a computer code developed by CHAM of North America Incorporated, under the contract RP 1066-1 from the Electric Power Research Institute, Palo Alto, California. ATHOS supersedes the earlier code URSULA2. ATHOS is designed for three-dimensional, steady state and transient analyses of PWR steam generators. The current version of the code has been checked out for: three different configurations of the recirculating-type U-tube steam generators; the homogeneous and algebraic-slip flow models; and full and part load operating conditions. The description of ATHOS is divided into four volumes. Volume 1 includes the mathematical and physical models and method of solution.

  6. Estimating pressurized water reactor decommissioning costs: A user`s manual for the PWR Cost Estimating Computer Program (CECP) software. Draft report for comment

    SciTech Connect

    Bierschbach, M.C.; Mencinsky, G.J.

    1993-10-01

    With the issuance of the Decommissioning Rule (July 27, 1988), nuclear power plant licensees are required to submit to the US Regulatory Commission (NRC) for review, decommissioning plans and cost estimates. This user`s manual and the accompanying Cost Estimating Computer Program (CECP) software provide a cost-calculating methodology to the NRC staff that will assist them in assessing the adequacy of the licensee submittals. The CECP, designed to be used on a personnel computer, provides estimates for the cost of decommissioning PWR plant stations to the point of license termination. Such cost estimates include component, piping, and equipment removal costs; packaging costs; decontamination costs; transportation costs; burial costs; and manpower costs. In addition to costs, the CECP also calculates burial volumes, person-hours, crew-hours, and exposure person-hours associated with decommissioning.

  7. Quantification of Uncertainties due to 235,238U, 239,240,241Pu and Fission Products Nuclear Data Uncertainties for a PWR Fuel Assembly

    NASA Astrophysics Data System (ADS)

    da Cruz, D. F.; Rochman, D.; Koning, A. J.

    2014-04-01

    Uncertainty analysis on reactivity and discharged inventory for a typical PWR fuel element as a result of uncertainties in 235,238U, 239,240,241Pu, and fission products nuclear data was performed. The Total Monte-Carlo (TMC) method was applied using the deterministic transport code DRAGON. The nuclear data used in this study is from the JEFF-3.1 evaluations, with the exception of the nuclear data files for U, Pu and fission products isotopes, which are taken from the nuclear data library TENDL-2012. Results show that the calculated total uncertainty in keff (as result of uncertainties in nuclear data of the considered isotopes) is virtually independent on fuel burnp and amounts to 700 pcm. The uncertainties in inventory of the discharged fuel is dependent on the element considered and lies in the range 1-15% for most fission products, and is below 5% for the most important actinides.

  8. On the condition of UO2 nuclear fuel irradiated in a PWR to a burn-up in excess of 110 MWd/kgHM

    NASA Astrophysics Data System (ADS)

    Restani, R.; Horvath, M.; Goll, W.; Bertsch, J.; Gavillet, D.; Hermann, A.; Martin, M.; Walker, C. T.

    2016-12-01

    Post-irradiation examination results are presented for UO2 fuel from a PWR fuel rod that had been irradiated to an average burn-up of 105 MWd/kgHM and showed high fission gas release of 42%. The radial distribution of xenon and the partitioning of fission gas between bubbles and the fuel matrix was investigated using laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) and electron probe microanalysis. It is concluded that release from the fuel at intermediate radial positions was mainly responsible for the high fission gas release. In this region thermal release had occurred from the high burn-up structure (HBS) at some point after the sixth irradiation cycle. The LA-ICP-MS results indicate that gas release had also occurred from the HBS in the vicinity of the pellet periphery. It is shown that the gas pressure in the HBS pores is well below the pressure that the fuel can sustain.

  9. Spent fuel dry storage technology development: thermal evaluation of isolated drywells containing spent fuel (1 kW PWR spent fuel assembly)

    SciTech Connect

    Unterzuber, R; Wright, J B

    1980-09-01

    A spent fuel Isolated Drywell Test was conducted at the Engine-Maintenance, Assembly and Disassembly (E-MAD) facility on the Nevada Test Site. Two PWR spent fuel assemblies having a decay heat level of approximately 1.1 kW were encapsulated inside the E-MAD Hot Bay and placed in instrumented near-surface drywell storage cells. Temperatures from the two isolated drywells and the adjacent soil have been recorded throughout the 19 month Isolated Drywell Test. Canister and drywell liner temperatures reached their peak values (254{sup 0}F and 203{sup 0}F, respectively) during August 1979. Thereafter, all temperatures decreased and showed a cycling pattern which responded to seasonal atmospheric temperature changes. A computer model was utilized to predict the thermal response of the drywell. Computer predictions of the drywell temperatures and the temperatures of the surrounding soil are presented and show good agreement with the test data.

  10. Materials Reliability Program: Environmental Fatigue Testing of Type 304L Stainless Steel U-Bends in Simulated PWR Primary Water (MRP-137)

    SciTech Connect

    R.Kilian

    2004-12-01

    Laboratory data generated in the past decade indicate a significant reduction in component fatigue life when reactor water environmental effects are experimentally simulated. However, these laboratory data have not been supported by nuclear power plant component operating experience. In recent comprehensive review of laboratory, component and structural test data performed through the EPRI Materials Reliability Program, flow rate was identified as a critical variable that was generally not considered in laboratory studies but applicable in plant operating environments. Available data for carbon/low-alloy steel piping components suggest that high flow is beneficial regarding the effects of a reactor water environment. Similar information is lacking for stainless steel piping materials. This report documents progress made to date in an extensive testing program underway to evaluate the effects of flow rate on the corrosion fatigue of 304L stainless steel under simulated PWR primary water environmental conditions.

  11. Reactivity and isotopic composition of spent PWR (pressurized-water-reactor) fuel as a function of initial enrichment, burnup, and cooling time

    SciTech Connect

    Cerne, S.P.; Hermann, O.W.; Westfall, R.M.

    1987-10-01

    This study presents the reactivity loss of spent PWR fuel due to burnup in terms of the infinite lattice multiplications factor, k/sub infinity/. Calculations were performed using the SAS2 and CSAS1 control modules of the SCALE system. The k/sub infinity/ values calculated for all combinations of six enrichments, seven burnups, and five cooling times. The results are presented as a primary function of enrichment in both tabular and graphic form. An equation has been developed to estimate the tabulated values of k/sub infinity/'s by specifying enrichment, cooling time, and burnup. Atom densities for fresh fuel, and spent fuel at cooling times of 2, 10, and 20 years are included. 13 refs., 8 figs., 8 tabs.

  12. International comparison of a depletion calculation benchmark devoted to fuel cycle issues results from the phase 1 dedicated to PWR-UOx fuels

    SciTech Connect

    Roque, B.; Kilger, R.; Laugier, F.; Marimbeau, P.; Riffard, C.; Thro, J. F.; Yudkevich, M.; Hesketh, K.; Sartori, E.

    2006-07-01

    This paper presents the results from the first phase of an international depletion calculations comparison devoted to PWR-UOx fuel cycle issues. This 'benchmark' has been defined within the NEA/OECD Working Party on Scientific Issues in Reactors Systems (WPRS). The aim is to investigate a large range of isotopes, physics quantities and fuel types applied to fuel and back-end cycle configurations. The results analyses have shown that there is a good agreement between participants for the mass calculation of many isotopes. However, it is interesting to observe that better agreement is obtained for isotopes which benefit from experimental validation. In this benchmark, the poorest agreement is obtained in calculating activation products originating from fuel impurities. Some discrepancies on neutron emission rates were also observed, mainly due to the discrepancies on masses calculations. Good agreement was obtained for the total decay heat calculation. (authors)

  13. Development of a Safeguards Verification Method and Instrument to Detect Pin Diversion from Pressurized Water Reactor (PWR) Spent Fuel Assemblies Phase I Study

    SciTech Connect

    Ham, Y S; Sitaraman, S

    2008-12-24

    A novel methodology to detect diversion of spent fuel from Pressurized Water Reactors (PWR) has been developed in order to address a long unsolved safeguards verification problem for international safeguards community such as International Atomic Energy Agency (IAEA) or European Atomic Energy Community (EURATOM). The concept involves inserting tiny neutron and gamma detectors into the guide tubes of a spent fuel assembly and measuring the signals. The guide tubes form a quadrant symmetric pattern in the various PWR fuel product lines and the neutron and gamma signals from these various locations are processed to obtain a unique signature for an undisturbed fuel assembly. Signatures based on the neutron and gamma signals individually or in a combination can be developed. Removal of fuel pins from the assembly will cause the signatures to be visibly perturbed thus enabling the detection of diversion. All of the required signal processing to obtain signatures can be performed on standard laptop computers. Monte Carlo simulation studies and a set of controlled experiments with actual commercial PWR spent fuel assemblies were performed and validated this novel methodology. Based on the simulation studies and benchmarking measurements, the methodology developed promises to be a powerful and practical way to detect partial defects that constitute 10% or more of the total active fuel pins. This far exceeds the detection threshold of 50% missing pins from a spent fuel assembly, a threshold defined by the IAEA Safeguards Criteria. The methodology does not rely on any operator provided data like burnup or cooling time and does not require movement of the fuel assembly from the storage rack in the spent fuel pool. A concept was developed to build a practical field device, Partial Defect Detector (PDET), which will be completely portable and will use standard radiation measuring devices already in use at the IAEA. The use of the device will not require any information provided

  14. Packing in protein cores

    NASA Astrophysics Data System (ADS)

    Gaines, J. C.; Clark, A. H.; Regan, L.; O'Hern, C. S.

    2017-07-01

    Proteins are biological polymers that underlie all cellular functions. The first high-resolution protein structures were determined by x-ray crystallography in the 1960s. Since then, there has been continued interest in understanding and predicting protein structure and stability. It is well-established that a large contribution to protein stability originates from the sequestration from solvent of hydrophobic residues in the protein core. How are such hydrophobic residues arranged in the core; how can one best model the packing of these residues, and are residues loosely packed with multiple allowed side chain conformations or densely packed with a single allowed side chain conformation? Here we show that to properly model the packing of residues in protein cores it is essential that amino acids are represented by appropriately calibrated atom sizes, and that hydrogen atoms are explicitly included. We show that protein cores possess a packing fraction of φ ≈ 0.56 , which is significantly less than the typically quoted value of 0.74 obtained using the extended atom representation. We also compare the results for the packing of amino acids in protein cores to results obtained for jammed packings from discrete element simulations of spheres, elongated particles, and composite particles with bumpy surfaces. We show that amino acids in protein cores pack as densely as disordered jammed packings of particles with similar values for the aspect ratio and bumpiness as found for amino acids. Knowing the structural properties of protein cores is of both fundamental and practical importance. Practically, it enables the assessment of changes in the structure and stability of proteins arising from amino acid mutations (such as those identified as a result of the massive human genome sequencing efforts) and the design of new folded, stable proteins and protein-protein interactions with tunable specificity and affinity.

  15. Iodine volatility. [PWR; BWR

    SciTech Connect

    Beahm, E.C.; Shockley, W.E.

    1984-01-01

    The ultimate aim of this program is to couple experimental aqueous iodine volatilities to a fission product release model. Iodine partition coefficients, for inorganic iodine, have been measured during hydrolysis and radiolysis. The hydrolysis experiments have illustrated the importance of reaction time on iodine volatility. However, radiolysis effects can override hydrolysis in determining iodine volatility. In addition, silver metal in radiolysis samples can react to form silver iodide accompanied by a decrease in iodine volatility. Experimental data are now being coupled to an iodine transport and release model that was developed in the Federal Republic of Germany.

  16. Crack growth rates and metallographic examinations of Alloy 600 and Alloy 82/182 from field components and laboratory materials tested in PWR environments.

    SciTech Connect

    Alexandreanu, B.; Chopra, O. K.; Shack, W. J.

    2008-05-05

    In light water reactors, components made of nickel-base alloys are susceptible to environmentally assisted cracking. This report summarizes the crack growth rate results and related metallography for field and laboratory-procured Alloy 600 and its weld alloys tested in pressurized water reactor (PWR) environments. The report also presents crack growth rate (CGR) results for a shielded-metal-arc weld of Alloy 182 in a simulated PWR environment as a function of temperature between 290 C and 350 C. These data were used to determine the activation energy for crack growth in Alloy 182 welds. The tests were performed by measuring the changes in the stress corrosion CGR as the temperatures were varied during the test. The difference in electrochemical potential between the specimen and the Ni/NiO line was maintained constant at each temperature by adjusting the hydrogen overpressure on the water supply tank. The CGR data as a function of temperature yielded activation energies of 252 kJ/mol for a double-J weld and 189 kJ/mol for a deep-groove weld. These values are in good agreement with the data reported in the literature. The data reported here and those in the literature suggest that the average activation energy for Alloy 182 welds is on the order of 220-230 kJ/mol, higher than the 130 kJ/mol commonly used for Alloy 600. The consequences of using a larger value of activation energy for SCC CGR data analysis are discussed.

  17. Bias estimates used in lieu of validation of fission products and minor actinides in MCNP Keff calculations for PWR burnup credit casks

    SciTech Connect

    Mueller, Don E.; Marshall, William J.; Wagner, John C.; Bowen, Douglas G.

    2015-09-01

    The U.S. Nuclear Regulatory Commission (NRC) Division of Spent Fuel Storage and Transportation recently issued Interim Staff Guidance (ISG) 8, Revision 3. This ISG provides guidance for burnup credit (BUC) analyses supporting transport and storage of PWR pressurized water reactor (PWR) fuel in casks. Revision 3 includes guidance for addressing validation of criticality (keff) calculations crediting the presence of a limited set of fission products and minor actinides (FP&MA). Based on previous work documented in NUREG/CR-7109, recommendation 4 of ISG-8, Rev. 3, includes a recommendation to use 1.5 or 3% of the FP&MA worth to conservatively cover the bias due to the specified FP&MAs. This bias is supplementary to the bias and bias uncertainty resulting from validation of keff calculations for the major actinides in SNF and does not address extension to actinides and fission products beyond those identified herein. The work described in this report involves comparison of FP&MA worths calculated using SCALE and MCNP with ENDF/B-V, -VI, and -VII based nuclear data and supports use of the 1.5% FP&MA worth bias when either SCALE or MCNP codes are used for criticality calculations, provided the other conditions of the recommendation 4 are met. The method used in this report may also be applied to demonstrate the applicability of the 1.5% FP&MA worth bias to other codes using ENDF/B V, VI or VII based nuclear data. The method involves use of the applicant s computational method to generate FP&MA worths for a reference SNF cask model using specified spent fuel compositions. The applicant s FP&MA worths are then compared to reference values provided in this report. The applicants FP&MA worths should not exceed the reference results by more than 1.5% of the reference FP&MA worths.

  18. Development and preliminary verification of the 3D core neutronic code: COCO

    SciTech Connect

    Lu, H.; Mo, K.; Li, W.; Bai, N.; Li, J.

    2012-07-01

    As the recent blooming economic growth and following environmental concerns (China)) is proactively pushing forward nuclear power development and encouraging the tapping of clean energy. Under this situation, CGNPC, as one of the largest energy enterprises in China, is planning to develop its own nuclear related technology in order to support more and more nuclear plants either under construction or being operation. This paper introduces the recent progress in software development for CGNPC. The focus is placed on the physical models and preliminary verification results during the recent development of the 3D Core Neutronic Code: COCO. In the COCO code, the non-linear Green's function method is employed to calculate the neutron flux. In order to use the discontinuity factor, the Neumann (second kind) boundary condition is utilized in the Green's function nodal method. Additionally, the COCO code also includes the necessary physical models, e.g. single-channel thermal-hydraulic module, burnup module, pin power reconstruction module and cross-section interpolation module. The preliminary verification result shows that the COCO code is sufficient for reactor core design and analysis for pressurized water reactor (PWR). (authors)

  19. Recent developments in pressure coring

    SciTech Connect

    McFall, A. L.

    1980-01-01

    The current rapid growth in the number of enhanced oil and gas recovery projects has created a strong demand for reservoir data such as true residual oil saturations. The companies providing pressure coring services have moved to fill this need. Two recent developments have emerged with the potential of significantly improving the present performance of pressure coring. Coring bits utilizing synthetic diamond cutters have demonstrated coring rates of one-foot per minute while improving core recovery. It is also apparent that cores of a near-unconsolidated nature are more easily recovered. In addition, a special low invasion fluid that is placed in the core retriever has demonstrated reduced core washing by the drilling mud and a decrease in the complexity of preparing cores for analysis. This paper describes the design, laboratory, and field testing efforts that led to these coring improvements. Also, experience in utilizing these developments while recovering over 100 cores is discussed.

  20. Core Noise - Increasing Importance

    NASA Technical Reports Server (NTRS)

    Hultgren, Lennart S.

    2011-01-01

    This presentation is a technical summary of and outlook for NASA-internal and NASA-sponsored external research on core (combustor and turbine) noise funded by the Fundamental Aeronautics Program Subsonic Fixed Wing (SFW) Project. Sections of the presentation cover: the SFW system-level noise metrics for the 2015, 2020, and 2025 timeframes; turbofan design trends and their aeroacoustic implications; the emerging importance of core noise and its relevance to the SFW Reduced-Perceived-Noise Technical Challenge; and the current research activities in the core-noise area, with additional details given about the development of a high-fidelity combustor-noise prediction capability as well as activities supporting the development of improved reduced-order, physics-based models for combustor-noise prediction. The need for benchmark data for validation of high-fidelity and modeling work and the value of a potential future diagnostic facility for testing of core-noise-reduction concepts are indicated. The NASA Fundamental Aeronautics Program has the principal objective of overcoming today's national challenges in air transportation. The SFW Reduced-Perceived-Noise Technical Challenge aims to develop concepts and technologies to dramatically reduce the perceived aircraft noise outside of airport boundaries. This reduction of aircraft noise is critical to enabling the anticipated large increase in future air traffic. Noise generated in the jet engine core, by sources such as the compressor, combustor, and turbine, can be a significant contribution to the overall noise signature at low-power conditions, typical of approach flight. At high engine power during takeoff, jet and fan noise have traditionally dominated over core noise. However, current design trends and expected technological advances in engine-cycle design as well as noise-reduction methods are likely to reduce non-core noise even at engine-power points higher than approach. In addition, future low-emission combustor

  1. Core Noise Reduction

    NASA Technical Reports Server (NTRS)

    Hultgren, Lennart S.

    2011-01-01

    This presentation is a technical summary of and outlook for NASA-internal and NASA-sponsored external research on core (combustor and turbine) noise funded by the Fundamental Aeronautics Program Subsonic Fixed Wing (SFW) Project. Sections of the presentation cover: the SFW system-level noise metrics for the 2015, 2020, and 2025 timeframes; turbofan design trends and their aeroacoustic implications; the emerging importance of core noise and its relevance to the SFW Reduce-Perceived-Noise Technical Challenge; and the current research activities in the core noise area. Recent work1 on the turbine-transmission loss of combustor noise is briefly described, two2,3 new NRA efforts in the core-noise area are outlined, and an effort to develop CMC-based acoustic liners for broadband noise reduction suitable for turbofan-core application is delineated. The NASA Fundamental Aeronautics Program has the principal objective of overcoming today's national challenges in air transportation. The reduction of aircraft noise is critical to enabling the anticipated large increase in future air traffic. The Subsonic Fixed Wing Project's Reduce-Perceived-Noise Technical Challenge aims to develop concepts and technologies to dramatically reduce the perceived aircraft noise outside of airport boundaries.

  2. Pressure Core Characterization

    NASA Astrophysics Data System (ADS)

    Santamarina, J. C.

    2014-12-01

    Natural gas hydrates form under high fluid pressure and low temperature, and are found in permafrost, deep lakes or ocean sediments. Hydrate dissociation by depressurization and/or heating is accompanied by a multifold hydrate volume expansion and host sediments with low permeability experience massive destructuration. Proper characterization requires coring, recovery, manipulation and testing under P-T conditions within the stability field. Pressure core technology allows for the reliable characterization of hydrate bearing sediments within the stability field in order to address scientific and engineering needs, including the measurement of parameters used in hydro-thermo-mechanical analyses, and the monitoring of hydrate dissociation under controlled pressure, temperature, effective stress and chemical conditions. Inherent sampling effects remain and need to be addressed in test protocols and data interpretation. Pressure core technology has been deployed to study hydrate bearing sediments at several locations around the world. In addition to pressure core testing, a comprehensive characterization program should include sediment analysis, testing of reconstituted specimens (with and without synthetic hydrate), and in situ testing. Pressure core characterization technology can be used to study other gas-charged formations such as deep sea sediments, coal bed methane and gas shales.

  3. Earth's core iron

    NASA Astrophysics Data System (ADS)

    Geophysicist J. Michael Brown of Texas A & M University noted recently at the Spring AGU Meeting in Baltimore that the structure and phase of metallic iron at pressures of the earth's inner core (approximately 3.3 Mbar) could have great significance in defining geometrical aspects of the core itself. Brown worked at the Los Alamos Scientific Laboratory with R.B. McQueen to redetermine the phase relations of metallic iron in a series of new shock-wave experiments. They found the melting point of iron at conditions equal to those at the boundary of the earth's outer (liquid) and inner (solid) cores to be 6000°±500°C (Geophysical Research Letters, 7, 533-536, 1980).

  4. Mars' Inner Core

    NASA Technical Reports Server (NTRS)

    1997-01-01

    This figure shows a cross-section of the planet Mars revealing an inner, high density core buried deep within the interior. Dipole magnetic field lines are drawn in blue, showing the global scale magnetic field that one associates with dynamo generation in the core. Mars must have one day had such a field, but today it is not evident. Perhaps the energy source that powered the early dynamo has shut down. The differentiation of the planet interior - heavy elements like iron sinking towards the center of the planet - can provide energy as can the formation of a solid core from the liquid.

    The Jet Propulsion Laboratory's Mars Surveyor Operations Project operates the Mars Global Surveyor spacecraft with its industrial partner, Lockheed Martin Astronautics, from facilities in Pasadena, CA and Denver, CO. JPL is an operating division of California Institute of Technology (Caltech).

  5. Molten core retention assembly

    DOEpatents

    Lampe, Robert F.

    1976-06-22

    Molten fuel produced in a core overheating accident is caught by a molten core retention assembly consisting of a horizontal baffle plate having a plurality of openings therein, heat exchange tubes having flow holes near the top thereof mounted in the openings, and a cylindrical, imperforate baffle attached to the plate and surrounding the tubes. The baffle assembly is supported from the core support plate of the reactor by a plurality of hanger rods which are welded to radial beams passing under the baffle plate and intermittently welded thereto. Preferably the upper end of the cylindrical baffle terminates in an outwardly facing lip to which are welded a plurality of bearings having slots therein adapted to accept the hanger rods.

  6. CORE SATURATION BLOCKING OSCILLATOR

    DOEpatents

    Spinrad, R.J.

    1961-10-17

    A blocking oscillator which relies on core saturation regulation to control the output pulse width is described. In this arrangement an external magnetic loop is provided in which a saturable portion forms the core of a feedback transformer used with the thermionic or semi-conductor active element. A first stationary magnetic loop establishes a level of flux through the saturation portion of the loop. A second adjustable magnet moves the flux level to select a saturation point giving the desired output pulse width. (AEC)

  7. Coupled full core neutron transport/CFD simulations of pressurized water reactors

    SciTech Connect

    Kochunas, B.; Stimpson, S.; Collins, B.; Downar, T.; Brewster, R.; Baglietto, E.; Yan, J.

    2012-07-01

    Recently as part of the CASL project, a capability to perform 3D whole-core coupled neutron transport and computational fluid dynamics (CFD) calculations was demonstrated. This work uses the 2D/1D transport code DeCART and the commercial CFD code STAR-CCM+. It builds on previous CASL work demonstrating coupling for smaller spatial domains. The coupling methodology is described along with the problem simulated and results are presented for fresh hot full power conditions. An additional comparison is made to an equivalent model that uses lower order T/H feedback to assess the importance and cost of high fidelity feedback to the neutronics problem. A simulation of a quarter core Combustion Engineering (CE) PWR core was performed with the coupled codes using a Fixed Point Gauss-Seidel iteration technique. The total approximate calculation requirements are nearly 10,000 CPU hours and 1 TB of memory. The problem took 6 coupled iterations to converge. The CFD coupled model and low order T/H feedback model compared well for global solution parameters, with a difference in the critical boron concentration and average outlet temperature of 14 ppm B and 0.94 deg. C, respectively. Differences in the power distribution were more significant with maximum relative differences in the core-wide pin peaking factor (Fq) of 5.37% and average relative differences in flat flux region power of 11.54%. Future work will focus on analyzing problems more relevant to CASL using models with less approximations. (authors)

  8. The Tom Core Complex

    PubMed Central

    Ahting, Uwe; Thun, Clemens; Hegerl, Reiner; Typke, Dieter; Nargang, Frank E.; Neupert, Walter; Nussberger, Stephan

    1999-01-01

    Translocation of nuclear-encoded preproteins across the outer membrane of mitochondria is mediated by the multicomponent transmembrane TOM complex. We have isolated the TOM core complex of Neurospora crassa by removing the receptors Tom70 and Tom20 from the isolated TOM holo complex by treatment with the detergent dodecyl maltoside. It consists of Tom40, Tom22, and the small Tom components, Tom6 and Tom7. This core complex was also purified directly from mitochondria after solubilization with dodecyl maltoside. The TOM core complex has the characteristics of the general insertion pore; it contains high-conductance channels and binds preprotein in a targeting sequence-dependent manner. It forms a double ring structure that, in contrast to the holo complex, lacks the third density seen in the latter particles. Three-dimensional reconstruction by electron tomography exhibits two open pores traversing the complex with a diameter of ∼2.1 nm and a height of ∼7 nm. Tom40 is the key structural element of the TOM core complex. PMID:10579717

  9. Theory of core excitons

    SciTech Connect

    Dow, J. D.; Hjalmarson, H. P.; Sankey, O. F.; Allen, R. E.; Buettner, H.

    1980-01-01

    The observation of core excitons with binding energies much larger than those of the valence excitons in the same material has posed a long-standing theoretical problem. A proposed solution to this problem is presented, and Frenkel excitons and Wannier excitons are shown to coexist naturally in a single material. (GHT)

  10. Modeling Core Collapse Supernovae

    NASA Astrophysics Data System (ADS)

    Mezzacappa, Anthony

    2017-01-01

    Core collapse supernovae, or the death throes of massive stars, are general relativistic, neutrino-magneto-hydrodynamic events. The core collapse supernova mechanism is still not in hand, though key components have been illuminated, and the potential for multiple mechanisms for different progenitors exists. Core collapse supernovae are the single most important source of elements in the Universe, and serve other critical roles in galactic chemical and thermal evolution, the birth of neutron stars, pulsars, and stellar mass black holes, the production of a subclass of gamma-ray bursts, and as potential cosmic laboratories for fundamental nuclear and particle physics. Given this, the so called ``supernova problem'' is one of the most important unsolved problems in astrophysics. It has been fifty years since the first numerical simulations of core collapse supernovae were performed. Progress in the past decade, and especially within the past five years, has been exponential, yet much work remains. Spherically symmetric simulations over nearly four decades laid the foundation for this progress. Two-dimensional modeling that assumes axial symmetry is maturing. And three-dimensional modeling, while in its infancy, has begun in earnest. I will present some of the recent work from the ``Oak Ridge'' group, and will discuss this work in the context of the broader work by other researchers in the field. I will then point to future requirements and challenges. Connections with other experimental, observational, and theoretical efforts will be discussed, as well.

  11. NUCLEAR REACTOR CORE DESIGN

    DOEpatents

    Mahlmeister, J.E.; Peck, W.S.; Haberer, W.V.; Williams, A.C.

    1960-03-22

    An improved core design for a sodium-cooled, graphitemoderated nuclear reactor is described. The improved reactor core comprises a number of blocks of moderator material, each block being in the shape of a regular prism. A number of channels, extending the length of each block, are disposed around the periphery. When several blocks are placed in contact to form the reactor core, the channels in adjacent blocks correspond with each other to form closed conduits extending the length of the core. Fuel element clusters are disposed in these closed conduits, and liquid coolant is forced through the annulus between the fuel cluster and the inner surface of the conduit. In a preferred embodiment of the invention, the moderator blocks are in the form of hexagonal prisms with longitudinal channels cut into the corners of the hexagon. The main advantage of an "edge-loaded" moderator block is that fewer thermal neutrons are absorbed by the moderator cladding, as compared with a conventional centrally loaded moderator block.

  12. Nucleosome Core Particle

    NASA Technical Reports Server (NTRS)

    1997-01-01

    Nucleosome Core Particle grown on STS-81. The fundamental structural unit of chromatin and is the basis for organization within the genome by compaction of DNA within the nucleus of the cell and by making selected regions of chromosomes available for transcription and replication. Principal Investigator's are Dr. Dan Carter and Dr. Gerard Bunick of New Century Pharmaceuticals.

  13. Authentic to the Core

    ERIC Educational Resources Information Center

    Kukral, Nicole; Spector, Stacy

    2012-01-01

    When educators think about what makes learning relevant to students, often they narrow their thinking to electives or career technical education. While these provide powerful opportunities for students to make relevant connections to their learning, they can also create authentic experiences in the core curriculum. In the San Juan Unified School…

  14. University City Core Plan.

    ERIC Educational Resources Information Center

    Philadelphia City Planning Commission, PA.

    A redevelopment plan for an urban core area of about 300 acres was warranted by--(1) unsuitable building conditions, (2) undesirable land usage, and (3) faulty traffic circulation. The plan includes expansion of two universities and creation of a regional science center, high school, and medical center. Guidelines for proposed land use and zoning…

  15. Some Core Contested Concepts

    ERIC Educational Resources Information Center

    Chomsky, Noam

    2015-01-01

    Core concepts of language are highly contested. In some cases this is legitimate: real empirical and conceptual issues arise. In other cases, it seems that controversies are based on misunderstanding. A number of crucial cases are reviewed, and an approach to language is outlined that appears to have strong conceptual and empirical motivation, and…

  16. Navagating the Common Core

    ERIC Educational Resources Information Center

    McShane, Michael Q.

    2014-01-01

    This article presents a debate over the Common Core State Standards Initiative as it has rocketed to the forefront of education policy discussions around the country. The author contends that there is value in having clear cross state standards that will clarify the new online and blended learning that the growing use of technology has provided…

  17. Some Core Contested Concepts

    ERIC Educational Resources Information Center

    Chomsky, Noam

    2015-01-01

    Core concepts of language are highly contested. In some cases this is legitimate: real empirical and conceptual issues arise. In other cases, it seems that controversies are based on misunderstanding. A number of crucial cases are reviewed, and an approach to language is outlined that appears to have strong conceptual and empirical motivation, and…

  18. Investigation of EAS cores

    NASA Astrophysics Data System (ADS)

    Shaulov, S. B.; Beyl, P. F.; Beysembaev, R. U.; Beysembaeva, E. A.; Bezshapov, S. P.; Borisov, A. S.; Cherdyntceva, K. V.; Chernyavsky, M. M.; Chubenko, A. P.; Dalkarov, O. D.; Denisova, V. G.; Erlykin, A. D.; Kabanova, N. V.; Kanevskaya, E. A.; Kotelnikov, K. A.; Morozov, A. E.; Mukhamedshin, R. A.; Nam, R. A.; Nesterova, N. M.; Nikolskaya, N. M.; Pavluchenko, V. P.; Piskal, V. V.; Puchkov, V. S.; Pyatovsky, S. E.; Ryabov, V. A.; Sadykov, T. Kh.; Schepetov, A. L.; Smirnova, M. D.; Stepanov, A. V.; Uryson, A. V.; Vavilov, Yu. N.; Vildanov, N. G.; Vildanova, L. I.; Zayarnaya, I. S.; Zhanceitova, J. K.; Zhukov, V. V.

    2017-06-01

    The development of nuclear-electromagnetic cascade models in air in the late forties have shown informational content of the study of cores of extensive air showers (EAS). These investigations were the main goal in different experiments which were carried out over many years by a variety of methods. Outcomes of such investigations obtained in the HADRON experiment using an X-ray emulsion chamber (XREC) as a core detector are considered. The Ne spectrum of EAS associated with γ-ray families, spectra of γ-rays (hadrons) in EAS cores and the Ne dependence of the muon number, ⟨Nμ⟩, in EAS with γ-ray families are obtained for the first time at energies of 1015-1017 eV with this method. A number of new effects were observed, namely, an abnormal scaling violation in hadron spectra which are fundamentally different from model predictions, an excess of muon number in EAS associated with γ-ray families, and the penetrating component in EAS cores. It is supposed that the abnormal behavior of γ-ray spectra and Ne dependence of the muon number are explained by the emergence of a penetrating component in the 1st PCR spectrum `knee' range. Nuclear and astrophysical explanations of the origin of the penetrating component are discussed. The necessity of considering the contribution of a single close cosmic-ray source to explain the PCR spectrum in the knee range is noted.

  19. Ultrasonic Drilling and Coring

    NASA Technical Reports Server (NTRS)

    Bar-Cohen, Yoseph

    1998-01-01

    A novel drilling and coring device, driven by a combination, of sonic and ultrasonic vibration, was developed. The device is applicable to soft and hard objects using low axial load and potentially operational under extreme conditions. The device has numerous potential planetary applications. Significant potential for commercialization in construction, demining, drilling and medical technologies.

  20. The Uncommon Core

    ERIC Educational Resources Information Center

    Ohler, Jason

    2013-01-01

    This author contends that the United States neglects creativity in its education system. To see this, he states, one may look at the Common Core State Standards. If one searches the English Language Arts and Literacy standards for the words "creative," "innovative," and "original"--and any associated terms, one will…

  1. Core Geometry Manual.

    ERIC Educational Resources Information Center

    Hirata, Li Ann

    Core Geometry is a course offered in the Option Y sequence of the high school mathematics program described by the Hawaii State Department of Education's guidelines. The emphasis of this course is on the general awareness and use of the relationships among points, lines, and figures in planes and space. This sample course is based on the…

  2. Looking for Core Values

    ERIC Educational Resources Information Center

    Carter, Margie

    2010-01-01

    People who view themselves as leaders, not just managers or teachers, are innovators who focus on clarifying core values and aligning all aspects of the organization with these values to grow their vision. A vision for an organization can't be just one person's idea. Visions grow by involving people in activities that help them name and create…

  3. Life from the core

    NASA Astrophysics Data System (ADS)

    Doglioni, Carlo; Coleman, Max; Pignatti, Johannes; Glassmeier, Karl-Heinz

    2010-05-01

    Life on Earth is the result of the chaotic combination of several independent chemical and physical parameters. One of them is the shield from ionizing radiation exerted by the atmosphere and the Earth's magnetic field. We hypothesise that the first few billion years of the Earth's history, dominated by bacteria, were characterized by stronger ionizing radiation. Bacteria can survive under such conditions better than any other organism. During the Archean and early Proterozoic the shield could have been weaker, allowing the development of only a limited number of species, more resistant to the external radiation. The Cambrian explosion of life could have been enhanced by the gradual growth of the solid inner core, which was not existent possibly before 1 Ga. The cooling of the Earth generated the solidification of the iron alloy in the center of the planet. As an hypothesis, before the crystallization of the core, the turbulence in the liquid core could have resulted in a lower or different magnetic field from the one we know today, being absent the relative rotation between inner and external core.

  4. Nucleosome Core Particle

    NASA Technical Reports Server (NTRS)

    1997-01-01

    Nucleosome Core Particle grown on STS-81. The fundamental structural unit of chromatin and is the basis for organization within the genome by compaction of DNA within the nucleus of the cell and by making selected regions of chromosomes available for transcription and replication. Principal Investigator's are Dr. Dan Carter and Dr. Gerard Bunick of New Century Pharmaceuticals.

  5. Navagating the Common Core

    ERIC Educational Resources Information Center

    McShane, Michael Q.

    2014-01-01

    This article presents a debate over the Common Core State Standards Initiative as it has rocketed to the forefront of education policy discussions around the country. The author contends that there is value in having clear cross state standards that will clarify the new online and blended learning that the growing use of technology has provided…

  6. Renewing the Core Curriculum

    ERIC Educational Resources Information Center

    Lawson, Hal A.

    2007-01-01

    The core curriculum accompanied the development of the academic discipline with multiple names such as Kinesiology, Exercise and Sport Science, and Health and Human Performance. It provides commonalties for undergraduate majors. It is timely to renew this curriculum. Renewal involves strategic reappraisals. It may stimulate change or reaffirm the…

  7. The Earth's Core.

    ERIC Educational Resources Information Center

    Jeanloz, Raymond

    1983-01-01

    The nature of the earth's core is described. Indirect evidence (such as that determined from seismological data) indicates that it is an iron alloy, solid toward its center but otherwise liquid. Evidence also suggests that it is the turbulent flow of the liquid that generates the earth's magnetic field. (JN)

  8. From Context to Core

    ERIC Educational Resources Information Center

    Campus Technology, 2008

    2008-01-01

    At Campus Technology 2008, Arizona State University Technology Officer Adrian Sannier mesmerized audiences with his mandate to become more efficient by doing only the "core" tech stuff--and getting someone else to slog through the context. This article presents an excerpt from Sannier's hour-long keynote address at Campus Technology '08. Sannier…

  9. Core Directions in HRD.

    ERIC Educational Resources Information Center

    1996

    This document consists of four papers presented at a symposium on core directions in human resource development (HRD) moderated by Verna Willis at the 1996 conference of the Academy of Human Resource Development. "Reengineering the Organizational HRD Function: Two Case Studies" (Neal Chalofsky) reports an action research study in which…

  10. Electromagnetic pump stator core

    DOEpatents

    Fanning, Alan W.; Olich, Eugene E.; Dahl, Leslie R.

    1995-01-01

    A stator core for supporting an electrical coil includes a plurality of groups of circumferentially abutting flat laminations which collectively form a bore and perimeter. A plurality of wedges are interposed between the groups, with each wedge having an inner edge and a thicker outer edge. The wedge outer edges abut adjacent ones of the groups to provide a continuous path around the perimeter.

  11. The Earth's Core.

    ERIC Educational Resources Information Center

    Jeanloz, Raymond

    1983-01-01

    The nature of the earth's core is described. Indirect evidence (such as that determined from seismological data) indicates that it is an iron alloy, solid toward its center but otherwise liquid. Evidence also suggests that it is the turbulent flow of the liquid that generates the earth's magnetic field. (JN)

  12. Core Competencies. SPEC Kit.

    ERIC Educational Resources Information Center

    McNeil, Beth, Comp.

    2002-01-01

    This SPEC (Systems and Procedures Exchange Center) Kit presents the results of a survey of Association of Research Libraries (ARL) member libraries designed to investigate the status of core competencies (i.e., the skills, knowledge, abilities, and attributes that employees across an organization are expected to have to contribute successfully…

  13. From Context to Core

    ERIC Educational Resources Information Center

    Campus Technology, 2008

    2008-01-01

    At Campus Technology 2008, Arizona State University Technology Officer Adrian Sannier mesmerized audiences with his mandate to become more efficient by doing only the "core" tech stuff--and getting someone else to slog through the context. This article presents an excerpt from Sannier's hour-long keynote address at Campus Technology '08. Sannier…

  14. ORNL rod-bundle heat-transfer test data. Volume 3. Thermal-hydraulic test facility experimental data report for test 3. 06. 6B - transient film boiling in upflow. [PWR

    SciTech Connect

    Mullins, C.B.; Felde, D.K.; Sutton, A.G.; Gould, S.S.; Morris, D.G.; Robinson, J.J.

    1982-05-01

    Reduced instrument responses are presented for Thermal-Hyraulic Test Facility (THTF) Test 3.06.6B. This test was conducted by members of the Oak Ridge National Laboratory Pressurized-Water-Reactor (PWR) Blowdown Heat Transfer (BDHT) Separate-Effects Program on August 29, 1980. The objective of the program was to investigate heat transfer phenomena believed to occur in PWR's during accidents, including small and large break loss-of-coolant accidents. Test 3.06.6B was conducted to obtain transient film boiling data in rod bundle geometry under reactor accident-type conditions. The primary purpose of this report is to make the reduced instrument responses for THTF Test 3.06.6B available. Included in the report are uncertainties in the instrument responses, calculated mass flows, and calculated rod powers.

  15. Efficiency and accuracy of the perturbation response coefficient generation method for whole core comet calculations in BWR and CANDU configurations

    SciTech Connect

    Zhang, D.; Rahnema, F.

    2013-07-01

    The coarse mesh transport method (COMET) is a highly accurate and efficient computational tool which predicts whole-core neutronics behaviors for heterogeneous reactor cores via a pre-computed eigenvalue-dependent response coefficient (function) library. Recently, a high order perturbation method was developed to significantly improve the efficiency of the library generation method. In that work, the method's accuracy and efficiency was tested in a small PWR benchmark problem. This paper extends the application of the perturbation method to include problems typical of the other water reactor cores such as BWR and CANDU bundles. It is found that the response coefficients predicted by the perturbation method for typical BWR bundles agree very well with those directly computed by the Monte Carlo method. The average and maximum relative errors in the surface-to-surface response coefficients are 0.02%-0.05% and 0.06%-0.25%, respectively. For CANDU bundles, the corresponding quantities are 0.01%-0.05% and 0.04% -0.15%. It is concluded that the perturbation method is highly accurate and efficient with a wide range of applicability. (authors)

  16. Lunar Polar Coring Lander

    NASA Technical Reports Server (NTRS)

    Angell, David; Bealmear, David; Benarroche, Patrice; Henry, Alan; Hudson, Raymond; Rivellini, Tommaso; Tolmachoff, Alex

    1990-01-01

    Plans to build a lunar base are presently being studied with a number of considerations. One of the most important considerations is qualifying the presence of water on the Moon. The existence of water on the Moon implies that future lunar settlements may be able to use this resource to produce things such as drinking water and rocket fuel. Due to the very high cost of transporting these materials to the Moon, in situ production could save billions of dollars in operating costs of the lunar base. Scientists have suggested that the polar regions of the Moon may contain some amounts of water ice in the regolith. Six possible mission scenarios are suggested which would allow lunar polar soil samples to be collected for analysis. The options presented are: remote sensing satellite, two unmanned robotic lunar coring missions (one is a sample return and one is a data return only), two combined manned and robotic polar coring missions, and one fully manned core retrieval mission. One of the combined manned and robotic missions has been singled out for detailed analysis. This mission proposes sending at least three unmanned robotic landers to the lunar pole to take core samples as deep as 15 meters. Upon successful completion of the coring operations, a manned mission would be sent to retrieve the samples and perform extensive experiments of the polar region. Man's first step in returning to the Moon is recommended to investigate the issue of lunar polar water. The potential benefits of lunar water more than warrant sending either astronauts, robots or both to the Moon before any permanent facility is constructed.

  17. Tensile and Fatigue Testing and Material Hardening Model Development for 508 LAS Base Metal and 316 SS Similar Metal Weld under In-air and PWR Primary Loop Water Conditions

    SciTech Connect

    Mohanty, Subhasish; Soppet, William; Majumdar, Saurin; Natesan, Ken

    2015-09-01

    This report provides an update on an assessment of environmentally assisted fatigue for light water reactor components under extended service conditions. This report is a deliverable in September 2015 under the work package for environmentally assisted fatigue under DOE’s Light Water Reactor Sustainability program. In an April 2015 report we presented a baseline mechanistic finite element model of a two-loop pressurized water reactor (PWR) for systemlevel heat transfer analysis and subsequent thermal-mechanical stress analysis and fatigue life estimation under reactor thermal-mechanical cycles. In the present report, we provide tensile and fatigue test data for 508 low-alloy steel (LAS) base metal, 508 LAS heat-affected zone metal in 508 LAS–316 stainless steel (SS) dissimilar metal welds, and 316 SS-316 SS similar metal welds. The test was conducted under different conditions such as in air at room temperature, in air at 300 oC, and under PWR primary loop water conditions. Data are provided on materials properties related to time-independent tensile tests and time-dependent cyclic tests, such as elastic modulus, elastic and offset strain yield limit stress, and linear and nonlinear kinematic hardening model parameters. The overall objective of this report is to provide guidance to estimate tensile/fatigue hardening parameters from test data. Also, the material models and parameters reported here can directly be used in commercially available finite element codes for fatigue and ratcheting evaluation of reactor components under in-air and PWR water conditions.

  18. Application of Core Dynamics Modeling to Core-Mantle Interactions

    NASA Technical Reports Server (NTRS)

    Kuang, Weijia

    2003-01-01

    Observations have demonstrated that length of day (LOD) variation on decadal time scales results from exchange of axial angular momentum between the solid mantle and the core. There are in general four core-mantle interaction mechanisms that couple the core and the mantle. Of which, three have been suggested likely the dominant coupling mechanism for the decadal core-mantle angular momentum exchange, namely, gravitational core-mantle coupling arising from density anomalies in the mantle and in the core (including the inner core), the electromagnetic coupling arising from Lorentz force in the electrically conducting lower mantle (e.g. D-layer), and the topographic coupling arising from non-hydrostatic pressure acting on the core-mantle boundary (CMB) topography. In the past decades, most effort has been on estimating the coupling torques from surface geomagnetic observations (kinematic approach), which has provided insights on the core dynamical processes. In the meantime, it also creates questions and concerns on approximations in the studies that may invalidate the corresponding conclusions. The most serious problem is perhaps the approximations that are inconsistent with dynamical processes in the core, such as inconsistencies between the core surface flow beneath the CMB and the CMB topography, and that between the D-layer electric conductivity and the approximations on toroidal field at the CMB. These inconsistencies can only be addressed with numerical core dynamics modeling. In the past few years, we applied our MoSST (Modular, Scalable, Self-consistent and Three-dimensional) core dynamics model to study core-mantle interactions together with geodynamo simulation, aiming at assessing the effect of the dynamical inconsistencies in the kinematic studies on core-mantle coupling torques. We focus on topographic and electromagnetic core-mantle couplings and find that, for the topographic coupling, the consistency between the core flow and the CMB topography is

  19. Application of Core Dynamics Modeling to Core-Mantle Interactions

    NASA Technical Reports Server (NTRS)

    Kuang, Weijia

    2003-01-01

    Observations have demonstrated that length of day (LOD) variation on decadal time scales results from exchange of axial angular momentum between the solid mantle and the core. There are in general four core-mantle interaction mechanisms that couple the core and the mantle. Of which, three have been suggested likely the dominant coupling mechanism for the decadal core-mantle angular momentum exchange, namely, gravitational core-mantle coupling arising from density anomalies in the mantle and in the core (including the inner core), the electromagnetic coupling arising from Lorentz force in the electrically conducting lower mantle (e.g. D-layer), and the topographic coupling arising from non-hydrostatic pressure acting on the core-mantle boundary (CMB) topography. In the past decades, most effort has been on estimating the coupling torques from surface geomagnetic observations (kinematic approach), which has provided insights on the core dynamical processes. In the meantime, it also creates questions and concerns on approximations in the studies that may invalidate the corresponding conclusions. The most serious problem is perhaps the approximations that are inconsistent with dynamical processes in the core, such as inconsistencies between the core surface flow beneath the CMB and the CMB topography, and that between the D-layer electric conductivity and the approximations on toroidal field at the CMB. These inconsistencies can only be addressed with numerical core dynamics modeling. In the past few years, we applied our MoSST (Modular, Scalable, Self-consistent and Three-dimensional) core dynamics model to study core-mantle interactions together with geodynamo simulation, aiming at assessing the effect of the dynamical inconsistencies in the kinematic studies on core-mantle coupling torques. We focus on topographic and electromagnetic core-mantle couplings and find that, for the topographic coupling, the consistency between the core flow and the CMB topography is

  20. Dynamics of core accretion

    DOE PAGES

    Nelson, Andrew F.; Ruffert, Maximilian

    2012-12-21

    In this paper, we perform three-dimensional hydrodynamic simulations of gas flowing around a planetary core of mass Mpl = 10M⊕ embedded in a near Keplerian background flow, using a modified shearing box approximation. We assume an ideal gas behaviour following an equation of state with a fixed ratio of the specific heats, γ = 1.42, consistent with the conditions of a moderate-temperature background disc with solar composition. No radiative heating or cooling is included in the models. We employ a nested grid hydrodynamic code implementing the ‘Piecewise Parabolic Method’ with as many as six fixed nested grids, providing spatial resolutionmore » on the finest grid comparable to the present-day diameters of Neptune and Uranus. We find that a strongly dynamically active flow develops such that no static envelope can form. The activity is not sensitive to plausible variations in the rotation curve of the underlying disc. It is sensitive to the thermodynamic treatment of the gas, as modelled by prescribed equations of state (either ‘locally isothermal’ or ‘locally isentropic’) and the temperature of the background disc material. The activity is also sensitive to the shape and depth of the core's gravitational potential, through its mass and gravitational softening coefficient. Each of these factors influences the magnitude and character of hydrodynamic feedback of the small-scale flow on the background, and we conclude that accurate modelling of such feedback is critical to a complete understanding of the core accretion process. The varying flow pattern gives rise to large, irregular eruptions of matter from the region around the core which return matter to the background flow: mass in the envelope at one time may not be found in the envelope at any later time. No net mass accretion into the envelope is observed over the course of the simulation and none is expected, due to our neglect of cooling. Except in cases of very rapid cooling however, as

  1. Dynamics of core accretion

    SciTech Connect

    Nelson, Andrew F.; Ruffert, Maximilian

    2012-12-21

    In this paper, we perform three-dimensional hydrodynamic simulations of gas flowing around a planetary core of mass Mpl = 10M embedded in a near Keplerian background flow, using a modified shearing box approximation. We assume an ideal gas behaviour following an equation of state with a fixed ratio of the specific heats, γ = 1.42, consistent with the conditions of a moderate-temperature background disc with solar composition. No radiative heating or cooling is included in the models. We employ a nested grid hydrodynamic code implementing the ‘Piecewise Parabolic Method’ with as many as six fixed nested grids, providing spatial resolution on the finest grid comparable to the present-day diameters of Neptune and Uranus. We find that a strongly dynamically active flow develops such that no static envelope can form. The activity is not sensitive to plausible variations in the rotation curve of the underlying disc. It is sensitive to the thermodynamic treatment of the gas, as modelled by prescribed equations of state (either ‘locally isothermal’ or ‘locally isentropic’) and the temperature of the background disc material. The activity is also sensitive to the shape and depth of the core's gravitational potential, through its mass and gravitational softening coefficient. Each of these factors influences the magnitude and character of hydrodynamic feedback of the small-scale flow on the background, and we conclude that accurate modelling of such feedback is critical to a complete understanding of the core accretion process. The varying flow pattern gives rise to large, irregular eruptions of matter from the region around the core which return matter to the background flow: mass in the envelope at one time may not be found in the envelope at any later time. No net mass accretion into the envelope is observed over the course of the simulation and none is expected, due to our neglect of cooling. Except in cases of very rapid cooling

  2. Long Valley Coring Project

    USGS Publications Warehouse

    Sass, John; Finger, John; McConnel, Vicki

    1998-01-01

    In December 1997, the California Energy Commission (CEC) agreed to provide funding for Phase III continued drilling of the Long Valley Exploratory Well (LVEW) near Mammoth Lakes, CA, from its present depth. The CEC contribution of $1 million completes a funding package of $2 million from a variety of sources, which will allow the well to be cored continuously to a depth of between 11,500 and 12,500 feet. The core recovered from Phase III will be crucial to understanding the origin and history of the hydrothermal systems responsible for the filling of fractures in the basement rock. The borehole may penetrate the metamorphic roof of the large magmatic complex that has fed the volcanism responsible for the caldera and subsequent activity.

  3. Geomagnetism of earth's core

    NASA Technical Reports Server (NTRS)

    Benton, E. R.

    1983-01-01

    Instrumentation, analytical methods, and research goals for understanding the behavior and source of geophysical magnetism are reviewed. Magsat, launched in 1979, collected global magnetometer data and identified the main terrestrial magnetic fields. The data has been treated by representing the curl-free field in terms of a scalar potential which is decomposed into a truncated series of spherical harmonics. Solutions to the Laplace equation then extend the field upward or downward from the measurement level through intervening spaces with no source. Further research is necessary on the interaction between harmonics of various spatial scales. Attempts are also being made to analytically model the main field and its secular variation at the core-mantle boundary. Work is also being done on characterizing the core structure, composition, thermodynamics, energetics, and formation, as well as designing a new Magsat or a tethered satellite to be flown on the Shuttle.

  4. Geomagnetism of earth's core

    NASA Technical Reports Server (NTRS)

    Benton, E. R.

    1983-01-01

    Instrumentation, analytical methods, and research goals for understanding the behavior and source of geophysical magnetism are reviewed. Magsat, launched in 1979, collected global magnetometer data and identified the main terrestrial magnetic fields. The data has been treated by representing the curl-free field in terms of a scalar potential which is decomposed into a truncated series of spherical harmonics. Solutions to the Laplace equation then extend the field upward or downward from the measurement level through intervening spaces with no source. Further research is necessary on the interaction between harmonics of various spatial scales. Attempts are also being made to analytically model the main field and its secular variation at the core-mantle boundary. Work is also being done on characterizing the core structure, composition, thermodynamics, energetics, and formation, as well as designing a new Magsat or a tethered satellite to be flown on the Shuttle.

  5. Core Outlet Temperature Study

    SciTech Connect

    Moisseytsev, A.; Hoffman, E.; Majumdar, S.

    2008-07-28

    It is a known fact that the power conversion plant efficiency increases with elevation of the heat addition temperature. The higher efficiency means better utilization of the available resources such that higher output in terms of electricity production can be achieved for the same size and power of the reactor core or, alternatively, a lower power core could be used to produce the same electrical output. Since any nuclear power plant, such as the Advanced Burner Reactor, is ultimately built to produce electricity, a higher electrical output is always desirable. However, the benefits of the higher efficiency and electricity production usually come at a price. Both the benefits and the disadvantages of higher reactor outlet temperatures are analyzed in this work.

  6. Constraints on silicates formation in the Si-Al-Fe system: Application to hard deposits in steam generators of PWR nuclear reactors

    NASA Astrophysics Data System (ADS)

    Berger, Gilles; Million-Picallion, Lisa; Lefevre, Grégory; Delaunay, Sophie

    2015-04-01

    Introduction: The hydrothermal crystallization of silicates phases in the Si-Al-Fe system may lead to industrial constraints that can be encountered in the nuclear industry in at least two contexts: the geological repository for nuclear wastes and the formation of hard sludges in the steam generator of the PWR nuclear plants. In the first situation, the chemical reactions between the Fe-canister and the surrounding clays have been extensively studied in laboratory [1-7] and pilot experiments [8]. These studies demonstrated that the high reactivity of metallic iron leads to the formation of Fe-silicates, berthierine like, in a wide range of temperature. By contrast, the formation of deposits in the steam generators of PWR plants, called hard sludges, is a newer and less studied issue which can affect the reactor performance. Experiments: We present here a preliminary set of experiments reproducing the formation of hard sludges under conditions representative of the steam generator of PWR power plant: 275°C, diluted solutions maintained at low potential by hydrazine addition and at alkaline pH by low concentrations of amines and ammoniac. Magnetite, a corrosion by-product of the secondary circuit, is the source of iron while aqueous Si and Al, the major impurities in this system, are supplied either as trace elements in the circulating solution or by addition of amorphous silica and alumina when considering confined zones. The fluid chemistry is monitored by sampling aliquots of the solution. Eh and pH are continuously measured by hydrothermal Cormet© electrodes implanted in a titanium hydrothermal reactor. The transformation, or not, of the solid fraction was examined post-mortem. These experiments evidenced the role of Al colloids as precursor of cements composed of kaolinite and boehmite, and the passivation of amorphous silica (becoming unreactive) likely by sorption of aqueous iron. But no Fe-bearing was formed by contrast to many published studies on the Fe

  7. Some core contested concepts.

    PubMed

    Chomsky, Noam

    2015-02-01

    Core concepts of language are highly contested. In some cases this is legitimate: real empirical and conceptual issues arise. In other cases, it seems that controversies are based on misunderstanding. A number of crucial cases are reviewed, and an approach to language is outlined that appears to have strong conceptual and empirical motivation, and to lead to conclusions about a number of significant issues that differ from some conventional beliefs.

  8. Banded electromagnetic stator core

    DOEpatents

    Fanning, Alan W.; Gonzales, Aaron A.; Patel, Mahadeo R.; Olich, Eugene E.

    1994-01-01

    A stator core for an electromagnetic pump includes a plurality of circumferentially adjoining groups of flat laminations disposed about a common centerline axis and collectively defining a central bore and a discontinuous outer perimeter, with adjacent groups diverging radially outwardly to form V-shaped gaps. An annular band surrounds the groups and is predeterminedly tensioned to clamp together the laminations, and has a predetermined flexibility in a radial direction to form substantially straight bridge sections between the adjacent groups.

  9. Variable depth core sampler

    DOEpatents

    Bourgeois, Peter M.; Reger, Robert J.

    1996-01-01

    A variable depth core sampler apparatus comprising a first circular hole saw member, having longitudinal sections that collapses to form a point and capture a sample, and a second circular hole saw member residing inside said first hole saw member to support the longitudinal sections of said first hole saw member and prevent them from collapsing to form a point. The second hole saw member may be raised and lowered inside said first hole saw member.

  10. Fissioning Plasma Core Reactor

    NASA Technical Reports Server (NTRS)

    Albright, Dennis; Butler, Carey; West, Nicole; Cole, John W. (Technical Monitor)

    2002-01-01

    Institute for Scientific Research, Inc. (ISR) research program consist of: 1.Study core physics by adapting existing codes: MCNP4C - Monte Carlo code; COMBINE/VENTURE - diffusion theory; SCALE4 - Monte Carlo, with many utility codes. 2. Determine feasibility and study major design parameters: fuel selection, temperature and reflector sizing. 3. Study reactor kinetics: develop QCALC1 to model point kinetics; study dynamic behavior of the power release.

  11. Banded electromagnetic stator core

    DOEpatents

    Fanning, Alan W.; Gonzales, Aaron A.; Patel, Mahadeo R.; Olich, Eugene E.

    1996-01-01

    A stator core for an electromagnetic pump includes a plurality of circumferentially adjoining groups of flat laminations disposed about a common centerline axis and collectively defining a central bore and a discontinuous outer perimeter, with adjacent groups diverging radially outwardly to form V-shaped gaps. An annular band surrounds the groups and is predeterminedly tensioned to clamp together the laminations, and has a predetermined flexibility in a radial direction to form substantially straight bridge sections between the adjacent groups.

  12. Banded electromagnetic stator core

    DOEpatents

    Fanning, A.W.; Gonzales, A.A.; Patel, M.R.; Olich, E.E.

    1994-04-05

    A stator core for an electromagnetic pump includes a plurality of circumferentially adjoining groups of flat laminations disposed about a common centerline axis and collectively defining a central bore and a discontinuous outer perimeter, with adjacent groups diverging radially outwardly to form V-shaped gaps. An annular band surrounds the groups and is predeterminedly tensioned to clamp together the laminations, and has a predetermined flexibility in a radial direction to form substantially straight bridge sections between the adjacent groups. 5 figures.

  13. Banded electromagnetic stator core

    DOEpatents

    Fanning, A.W.; Gonzales, A.A.; Patel, M.R.; Olich, E.E.

    1996-06-11

    A stator core for an electromagnetic pump includes a plurality of circumferentially adjoining groups of flat laminations disposed about a common centerline axis and collectively defining a central bore and a discontinuous outer perimeter, with adjacent groups diverging radially outwardly to form V-shaped gaps. An annular band surrounds the groups and is predeterminedly tensioned to clamp together the laminations, and has a predetermined flexibility in a radial direction to form substantially straight bridge sections between the adjacent groups. 5 figs.

  14. Electromagnetic pump stator core

    DOEpatents

    Fanning, A.W.; Olich, E.E.; Dahl, L.R.

    1995-01-17

    A stator core for supporting an electrical coil includes a plurality of groups of circumferentially abutting flat laminations which collectively form a bore and perimeter. A plurality of wedges are interposed between the groups, with each wedge having an inner edge and a thicker outer edge. The wedge outer edges abut adjacent ones of the groups to provide a continuous path around the perimeter. 21 figures.

  15. Cross Cell Sandwich Core

    NASA Technical Reports Server (NTRS)

    Ford, Donald B. (Inventor)

    2004-01-01

    A sandwich core comprises two faceplates separated by a plurality of cells. The cells are comprised of walls positioned at oblique angles relative to a perpendicular axis extending through the faceplates. The walls preferably form open cells and are constructed from open cells and are constructed from rows of ribbons. The walls may be obliquely angled relative to more than one plane extending through the perpendicular axis.

  16. Variable depth core sampler

    DOEpatents

    Bourgeois, P.M.; Reger, R.J.

    1996-02-20

    A variable depth core sampler apparatus is described comprising a first circular hole saw member, having longitudinal sections that collapses to form a point and capture a sample, and a second circular hole saw member residing inside said first hole saw member to support the longitudinal sections of said first hole saw member and prevent them from collapsing to form a point. The second hole saw member may be raised and lowered inside said first hole saw member. 7 figs.

  17. Toroidal core winder

    DOEpatents

    Potthoff, Clifford M.

    1978-01-01

    The disclosure is directed to an apparatus for placing wire windings on a toroidal body, such as a transformer core, having an orifice in its center. The apparatus comprises a wire storage spool, a wire loop holding continuous belt maintained in a C-shaped loop by a belt supporting structure and provision for turning the belt to place and tighten loops of wire on a toroidal body, which is disposed within the gap of the C-shaped belt loop.

  18. Core-collapse Supernovae

    SciTech Connect

    Hix, William Raphael; Lentz, E. J.; Baird, Mark L; Chertkow, Merek A; Lee, Ching-Tsai; Blondin, J. M.; Bruenn, S. W.; Messer, Bronson; Mezzacappa, Anthony

    2013-01-01

    Marking the inevitable death of a massive star, and the birth of a neutron star or black hole, core-collapse supernovae bring together physics at a wide range in spatial scales, from kilometer-sized hydrodynamic motions (growing to gigameter scale) down to femtometer scale nuclear reactions. Carrying 10$^{51}$ ergs of kinetic energy and a rich-mix of newly synthesized atomic nuclei, core-collapse supernovae are the preeminent foundries of the nuclear species which make up ourselves and our solar system. We will discuss our emerging understanding of the convectively unstable, neutrino-driven explosion mechanism, based on increasingly realistic neutrino-radiation hydrodynamic simulations that include progressively better nuclear and particle physics. Recent multi-dimensional models with spectral neutrino transport from several research groups, which slowly develop successful explosions for a range of progenitors, have motivated changes in our understanding of the neutrino reheating mechanism. In a similar fashion, improvements in nuclear physics, most notably explorations of weak interactions on nuclei and the nuclear equation of state, continue to refine our understanding of how supernovae explode. Recent progress on both the macroscopic and microscopic effects that affect core-collapse supernovae are discussed.

  19. GEOS-CORE

    SciTech Connect

    2014-06-24

    GEOS-CORE is a code that integrates open source Libraries for linear algebra and I/O with two main LLNL-written components: (i) a set of standard finite, discrete, and discontinuous displacement element physics solvers for resolving Darcy fluid flow, explicit mechanics, implicit mechanics, and fluid-mediated fracturing, including resolution of physical behaviors both implicitly and explicitly, and (ii) a MPI-based parallelization implementation for use on generic HPC distributed memory architectures. The resultant code can be used alone for linearly elastic and quasistatic damage problems; problems involving hydraulic fracturing, where the mesh topology is dynamically changed; and general granular materials behavior. The key application domain is for low-rate stimulation and fracture control in subsurface reservoirs (e.g., enhanced geothermal sites and unconventional shale gas stimulation). GEOS-CORE also has interfaces to call external libraries for, e.g., material models and equations fo state; however, LLNL-developed EOS and material models, beyond the aforementioned linear elastic and quasi-static damage models, will not be part of the current release. GEOS-CORE's secondary applications include granular materials behavior under different load paths.

  20. 33. BENCH CORE STATION, GREY IRON FOUNDRY CORE ROOM WHERE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    33. BENCH CORE STATION, GREY IRON FOUNDRY CORE ROOM WHERE CORE MOLDS WERE HAND FILLED AND OFTEN PNEUMATICALLY COMPRESSED WITH A HAND-HELD RAMMER BEFORE THEY WERE BAKED. - Stockham Pipe & Fittings Company, Grey Iron Foundry, 4000 Tenth Avenue North, Birmingham, Jefferson County, AL

  1. Selenium semiconductor core optical fibers

    SciTech Connect

    Tang, G. W.; Qian, Q. Peng, K. L.; Wen, X.; Zhou, G. X.; Sun, M.; Chen, X. D.; Yang, Z. M.

    2015-02-15

    Phosphate glass-clad optical fibers containing selenium (Se) semiconductor core were fabricated using a molten core method. The cores were found to be amorphous as evidenced by X-ray diffraction and corroborated by Micro-Raman spectrum. Elemental analysis across the core/clad interface suggests that there is some diffusion of about 3 wt % oxygen in the core region. Phosphate glass-clad crystalline selenium core optical fibers were obtained by a postdrawing annealing process. A two-cm-long crystalline selenium semiconductor core optical fibers, electrically contacted to external circuitry through the fiber end facets, exhibit a three times change in conductivity between dark and illuminated states. Such crystalline selenium semiconductor core optical fibers have promising utility in optical switch and photoconductivity of optical fiber array.

  2. Core Formation Process and Light Elements in the Planetary Core

    NASA Astrophysics Data System (ADS)

    Ohtani, E.; Sakairi, T.; Watanabe, K.; Kamada, S.; Sakamaki, T.; Hirao, N.

    2015-12-01

    Si, O, and S are major candidates for light elements in the planetary core. In the early stage of the planetary formation, the core formation started by percolation of the metallic liquid though silicate matrix because Fe-S-O and Fe-S-Si eutectic temperatures are significantly lower than the solidus of the silicates. Therefore, in the early stage of accretion of the planets, the eutectic liquid with S enrichment was formed and separated into the core by percolation. The major light element in the core at this stage will be sulfur. The internal pressure and temperature increased with the growth of the planets, and the metal component depleted in S was molten. The metallic melt contained both Si and O at high pressure in the deep magma ocean in the later stage. Thus, the core contains S, Si, and O in this stage of core formation. Partitioning experiments between solid and liquid metals indicate that S is partitioned into the liquid metal, whereas O is weakly into the liquid. Partitioning of Si changes with the metallic iron phases, i.e., fcc iron-alloy coexisting with the metallic liquid below 30 GPa is depleted in Si. Whereas hcp-Fe alloy above 30 GPa coexisting with the liquid favors Si. This contrast of Si partitioning provides remarkable difference in compositions of the solid inner core and liquid outer core among different terrestrial planets. Our melting experiments of the Fe-S-Si and Fe-O-S systems at high pressure indicate the core-adiabats in small planets, Mercury and Mars, are greater than the slope of the solidus and liquidus curves of these systems. Thus, in these planets, the core crystallized at the top of the liquid core and 'snowing core' formation occurred during crystallization. The solid inner core is depleted in both Si and S whereas the liquid outer core is relatively enriched in Si and S in these planets. On the other hand, the core adiabats in large planets, Earth and Venus, are smaller than the solidus and liquidus curves of the systems. The

  3. Hollow-Core Fiber Lamp

    NASA Technical Reports Server (NTRS)

    Yi, Lin (Inventor); Tjoelker, Robert L. (Inventor); Burt, Eric A. (Inventor); Huang, Shouhua (Inventor)

    2016-01-01

    Hollow-core capillary discharge lamps on the millimeter or sub-millimeter scale are provided. The hollow-core capillary discharge lamps achieve an increased light intensity ratio between 194 millimeters (useful) and 254 millimeters (useless) light than conventional lamps. The capillary discharge lamps may include a cone to increase light output. Hollow-core photonic crystal fiber (HCPCF) may also be used.

  4. Faculty Supports Communication Core Courses.

    ERIC Educational Resources Information Center

    Kopenhaver, Lillian Lodge; And Others

    1989-01-01

    Asks public relations educators what they think about core classes required for students in their field. Finds they generally support the idea that their students should take core mass communications courses, even if such core courses are developed from a traditional journalism/news-editorial standpoint. (MS)

  5. Sneak in Some Core Subjects

    ERIC Educational Resources Information Center

    Clarke, Lynne

    2011-01-01

    Even if students don't have an aversion to core subjects, they may not see the relationship between the core subjects and their career path. In this article, the author outlines a career path project that can be adapted to work in any career and technical education (CTE) class to highlight the relationship between core subjects and the real world.…

  6. Mercury's inner core size and core-crystallization regime

    NASA Astrophysics Data System (ADS)

    Dumberry, Mathieu; Rivoldini, Attilio

    2015-03-01

    Earth-based radar observation of Mercury's rotation vector combined with gravity observation by the MESSENGER spacecraft yield a measure of Mercury's moment of inertia and the amplitude of the 88-day libration of its silicate shell. These two geodetic constraints provide information on Mercury's interior structure, including the presence of a fluid core, the radius of the core-mantle boundary and the bulk densities of the core and mantle. In this work, we show how they further provide information on the size of the solid inner core and on the crystallization regime of the fluid core. If Mercury's fluid core is a Fe-FeS alloy with a sulfur concentration on the Fe-rich side of the eutectic, the largest inner core compatible with geodetic observations at the 1σ level is 1325 ± 250 km. Our results further suggest that the crystallization scenario that best fits the geodetic observations involves the formation of Fe-snow within the fluid core, and that this scenario is preferred for models with an iron-poor mantle composition. Consequently, Mercury's dynamo most likely operates in concert with snow formation. For an inner core larger than ∼650 km, snow formation extends to the inner core boundary. If a dynamo cannot be maintained by the dynamics of snow formation, or if such dynamo produces a magnetic field incompatible with observation, Mercury's inner core must then be smaller than 650 km.

  7. FEMAXI-V benchmarking study on peak temperature and fission gas release prediction of PWR rod fuel

    NASA Astrophysics Data System (ADS)

    Suwardi, Dewayatna, W.; Briyatmoko, B.

    2012-06-01

    The present paper reports a study of FEMAXI-V code and related report on code benchmarking. Capabilities of the FEMAXI-V code to predict the thermal and fission gas release have been tested on MOX fuels in LWRs which has been done in SCK.CEN & Belgonucleaire by using PRIMO MOX rod BD8 irradiation experiment after V Sobolev as reported O. J. Ott [2]. Base irradiation in the BR3 reactor, the BD8 rod was transported to CEA-Saclay for irradiation in the OSIRIS reactor (ramp power excursion). The irradiation device used for the PRIMO ramps was the ISABELLE 1 loop, installed on a movable structure of the core periphery. The power variations were obtained by inwards/backwards movements of the loop in the core water. The preconditioning phase for rod BD8 occurred at a peak power level of 189 W/cm with a hold time of 27 hours. The subsequent power excursion rate amounted to 77 W/ (cm.min), reaching a terminal peak power level of 395 W/cm that lasted for 20 hours.

  8. FEMAXI-V benchmarking study on peak temperature and fission gas release prediction of PWR rod fuel

    SciTech Connect

    Suwardi; Dewayatna, W.; Briyatmoko, B.

    2012-06-06

    The present paper reports a study of FEMAXI-V code and related report on code benchmarking. Capabilities of the FEMAXI-V code to predict the thermal and fission gas release have been tested on MOX fuels in LWRs which has been done in SCK{center_dot}CEN and Belgonucleaire by using PRIMO MOX rod BD8 irradiation experiment after V Sobolev as reported O. J. Ott. Base irradiation in the BR3 reactor, the BD8 rod was transported to CEA-Saclay for irradiation in the OSIRIS reactor (ramp power excursion). The irradiation device used for the PRIMO ramps was the ISABELLE 1 loop, installed on a movable structure of the core periphery. The power variations were obtained by inwards/backwards movements of the loop in the core water. The preconditioning phase for rod BD8 occurred at a peak power level of 189 W/cm with a hold time of 27 hours. The subsequent power excursion rate amounted to 77 W/ (cm.min), reaching a terminal peak power level of 395 W/cm that lasted for 20 hours.

  9. In-Vessel Retention Technology Development and Use for Advanced PWR Designs in the USA and Korea

    SciTech Connect

    T.G. Theofanous; S.J. Oh; J.H. Scobel

    2004-05-18

    In-Vessel Retention (IVR) of molten core debris by means of external reactor vessel flooding is a cornerstone of severe accident management for Westinghouse's AP600 (advanced passive light water reactor) design. The case for its effectiveness (made in previous work by the PI) has been thoroughly documented, reviewed as part of the licensing certification, and accepted by the US Nuclear Regulatory Commission. A successful IVR would terminate a severe accident, passively, with the core in a stable, coolable configuration (within the lower head), thus avoiding the largely uncertain accident evolution with the molten debris on the containment floor. This passive plant design has been upgraded by Westinghouse to the AP1000, a 1000 MWe plant very similar to the AP600. The severe accident management approach is very similar too, including In-Vessel Retention as the cornerstone feature, and initial evaluations indicated that this would be feasible at the higher power as well. A similar strategy is adopted in Korea for the APR1400 plant. The overall goal of this project is to provide experimental data and develop the necessary basic understanding so as to allow the robust extension of the AP600 In-Vessel Retention strategy for severe accident management to higher power reactors, and in particular, to the AP1000 advanced passive design.

  10. Automated Core Design

    SciTech Connect

    Kobayashi, Yoko; Aiyoshi, Eitaro

    2005-07-15

    Multistate searching methods are a subfield of distributed artificial intelligence that aims to provide both principles for construction of complex systems involving multiple states and mechanisms for coordination of independent agents' actions. This paper proposes a multistate searching algorithm with reinforcement learning for the automatic core design of a boiling water reactor. The characteristics of this algorithm are that the coupling structure and the coupling operation suitable for the assigned problem are assumed and an optimal solution is obtained by mutual interference in multistate transitions using multiagents. Calculations in an actual plant confirmed that the proposed algorithm increased the convergence ability of the optimization process.

  11. CANOPEN Controller IP Core

    NASA Astrophysics Data System (ADS)

    Caramia, Maurizio; Montagna, Mario; Furano, Gianluca; Winton, Alistair

    2010-08-01

    This paper will describe the activities performed by Thales Alenia Space Italia supported by the European Space Agency in the definition of a CAN bus interface to be used on Exomars. The final goal of this activity is the development of an IP core, to be used in a slave node, able to manage both the CAN bus Data Link and Application Layer totally in hardware. The activity has been focused on the needs of the EXOMARS mission where devices with different computational performances are all managed by the onboard computer through the CAN bus.

  12. PROCESS FOR JACKETING A CORE

    DOEpatents

    Last, G.A.

    1960-07-19

    A process is given for enclosing the uranium core of a nuclear fuel element by placing the core in an aluminum cup and closing the open end of the cup over the core. As the metal of the cup is brought together in a weld over the center of the end of the core, it is extruded inwardly as internal projection into a central recess in the core and outwardly as an external projection. Thus oxide inclusions in the weld of the cup are spread out into the internal and external projections and do not interfere with the integrity of the weld.

  13. A Study on Structured Simulation Framework for Design and Evaluation of Human-Machine Interface System -Application for On-line Risk Monitoring for PWR Nuclear Power Plant-

    SciTech Connect

    Zhan, J.; Yang, M.; Li, S.C.; Peng, M.J.; Yan, S.Y.; Zhang, Z.J.

    2006-07-01

    The operators in the main control room of Nuclear Power Plant (NPP) need to monitor plant condition through operation panels and understand the system problems by their experiences and skills. It is a very hard work because even a single fault will cause a large number of plant parameters abnormal and operators are required to perform trouble-shooting actions in a short time interval. It will bring potential risks if operators misunderstand the system problems or make a commission error to manipulate an irrelevant switch with their current operation. This study aims at developing an on-line risk monitoring technique based on Multilevel Flow Models (MFM) for monitoring and predicting potential risks in current plant condition by calculating plant reliability. The proposed technique can be also used for navigating operators by estimating the influence of their operations on plant condition before they take an action that will be necessary in plant operation, and therefore, can reduce human errors. This paper describes the risk monitoring technique and illustrates its application by a Steam Generator Tube Rupture (SGTR) accident in a 2-loop Pressurized Water Reactor (PWR) Marine Nuclear Power Plant (MNPP). (authors)

  14. The role of Hydrogen and Creep in Intergranular Stress Corrosion Cracking of Alloy 600 and Alloy 690 in PWR Primary Water Environments ? a Review

    SciTech Connect

    Rebak, R B; Hua, F H

    2004-07-12

    Intergranular attack (IGA) and intergranular stress corrosion cracking (IGSCC) of Alloy 600 in PWR steam generator environment has been extensively studied for over 30 years without rendering a clear understanding of the essential mechanisms. The lack of understanding of the IGSCC mechanism is due to a complex interaction of numerous variables such as microstructure, thermomechanical processing, strain rate, water chemistry and electrochemical potential. Hydrogen plays an important role in all these variables. The complexity, however, significantly hinders a clearer and more fundamental understanding of the mechanism of hydrogen in enhancing intergranular cracking via whatever mechanism. In this work, an attempt is made to review the role of hydrogen based on the current understanding of grain boundary structure and chemistry and intergranular fracture of nickel alloys, effect of hydrogen on electrochemical behavior of Alloy 600 and Alloy 690 (e.g. the passive film stability, polarization behavior and open-circuit potential) and effect of hydrogen on PWSCC behavior of Alloy 600 and Alloy 690. Mechanistic studies on the PWSCC are briefly reviewed. It is concluded that further studies on the role of hydrogen on intergranular cracking in both inert and primary side environments are needed. These studies should focus on the correlation of the results obtained at different laboratories by different methods on materials with different metallurgical and chemical parameters.

  15. Experimental evidence of oxygen thermo-migration in PWR UO2 fuels during power ramps using in-situ oxido-reduction indicators

    NASA Astrophysics Data System (ADS)

    Riglet-Martial, Ch.; Sercombe, J.; Lamontagne, J.; Noirot, J.; Roure, I.; Blay, T.; Desgranges, L.

    2016-11-01

    The present study describes the in-situ electrochemical modifications which affect irradiated PWR UO2 fuels in the course of a power ramp, by means of in-situ oxido-reduction indicators such as chromium or neo-formed chemical phases. It is shown that irradiated fuels (of nominal stoichiometry close to 2.000) under temperature gradient such as that occurring during high power transients are submitted to strong oxido-reduction perturbations, owing to radial migration of oxygen from the hot center to the cold periphery of the pellet. The oxygen redistribution, similar to that encountered in Sodium Fast Reactors fuels, induces a massive reduction/precipitation of the fission products Mo, Ru, Tc and Cr (if present) in the high temperature pellet section and the formation of highly oxidized neo-formed grey phases of U4O9 type in its cold section, of lower temperature. The parameters governing the oxidation states of UO2 fuels under power ramps are finally debated from a cross-analysis of our results and other published information. The potential chemical benefits brought by oxido-reductive additives in UO2 fuel such as chromium oxide, in connection with their oxygen buffering properties, are discussed.

  16. Development of self-interrogation neutron resonance densitometry (SINRD) to measure U-235 and Pu-239 content in a PWR spent fuel assembly

    SciTech Connect

    Lafleur, Adrienne M; Charlton, William S; Menlove, Howard O; Swinhoe, Martyn T

    2009-01-01

    The use of Self-Interrogation Neutron Resonance Densitometry (SINRD) to measure the {sup 235}U and {sup 239}Pu content in a PWR spent fuel assembly was investigated via Monte Carlo N-Particle eXtended transport code (MCNPX) simulations. The sensitivity of SINRD is based on using the same fissile materials in the fission chambers as are present in the fuel because the effect of resonance absorption lines in the transmitted flux is amplified by the corresponding (n, f) reaction peaks in fission chamber. These simulations utilize the {sup 244}Cm spontaneous fission neutrons to self-interrogate the fuel pins. The amount of resonance absorption of these neutrons in the fuel can be measured using {sup 235}U and {sup 239}Pu fission chambers placed adjacent to the assembly. We used ratios of different fission chambers to reduce the sensitivity of the measurements to extraneous material present in fuel. The development of SINRD to measure the fissile content in spent fuel is of great importance to the improvement of nuclear safeguards and material accountability. Future work includes the use of this technique to measure the fissile content in FBR spent fuel and heavy metal product from reprocessing methods.

  17. Probability of pipe fracture in the primary coolant loop of a PWR plant. Volume 5. Probabilistic fracture mechanics analysis. Load Combination Program Project I final report

    SciTech Connect

    Harris, D.O.; Lim, E.Y.; Dedhia, D.D.

    1981-06-01

    The primary purpose of the Load Combination Program covered in this report is to estimate the probability of a seismic induced LOCA in the primary piping of a commercial pressurized water reactor (PWR). Best estimates, rather than upper bound results are desired. This was accomplished by use of a fracture mechanics model that employs a random distribution of initial cracks in the piping welds. Estimates of the probability of cracks of various sizes initially existing in the welds are combined with fracture mechanics calculations of how these cracks would grow during service. This then leads to direct estimates of the probability of failure as a function of time and location within the piping system. The influence of varying the stress history to which the piping is subjected is easily determined. Seismic events enter into the analysis through the stresses they impose on the pipes. Hence, the influence of various seismic events on the piping failure probability can be determined, thereby providing the desired information.

  18. On-line fission products measurements during a PWR severe accident: the French DECA-PF project

    SciTech Connect

    Ducros, G.; Allinei, P.G.; Roure, C.; Rozel, C.; Blanc De Lanaute, N.; Musoyan, G.

    2015-07-01

    Following the Fukushima accident, a lot of recommendations was drawn by international organizations (IAEA, OECD, NUGENIA network...) in order to improve the safety in such accidental conditions and mitigate their consequences. One of these recommendations was to improve the robustness of the instrumentation, which was dramatically lacking at Fukushima, as well as to better determine the Source Term involved in nuclear accident. The DECA-PF project (Diagnosis of a degraded reactor core through Fission Product measurements) was elaborated in this context and selected as one of 21 collaborative R and D projects in the field of nuclear safety and radioprotection, funded in May 2013 by the French National Research Agency. Over the months following the Fukushima accident, a CEA crisis team was held in order to analyze on-line the situation taking into account the data delivered by TEPCO and other organizations. Despite the difficulties encountered concerning the reliability of these data, the work performed showed the high capacity of Fission Products (FP) measurements to get a diagnosis relative to the status of the reactors and the spent fuel pools (SFP). Based on these FP measurements, it was possible to conclude that the main origin of the releases was coming from the cores and not from the SFP, in particular for SFP-4 which was of high concern, and that the degradation level of the reactors was very large, including probably an extensive core melting. To improve the reliability of this kind of diagnosis, the necessity to get such measurements as soon as possible after the accident and as near as possible from the reactor was stressed. In this way the present DECA-PF project intends to develop a new and innovative instrumentation taking into account the design of the French nuclear power plants on which sand bed filters have been implemented for severe accident management. Three complementary techniques, devoted to measure the FP release on-line, are being studied

  19. Core-tube data logger

    SciTech Connect

    Henfling, J.A.; Normann, R.A.; Knudsen, S.; Drumheller, D.

    1997-01-01

    Wireline core drilling, increasingly used for geothermal exploration, employs a core-tube to capture a rock core sample during drilling. Three types of core-tube data loggers (CTDL) have been built and tested to date by Sandia national Laboratories. They are: (1) temperature-only logger, (2) temperature/inclinometer logger and (3) heat-shielded temperature/inclinometer logger. All were tested during core drilling operations using standard wireline diamond core drilling equipment. While these tools are designed for core-tube deployment, the tool lends itself to be adapted to other drilling modes and equipment. Topics covered in this paper include: (1) description on how the CTDLs are implemented, (2) the components of the system, (3) the type of data one can expect from this type of tool, (4) lessons learned, (5) comparison to its counterpart and (6) future work.

  20. Models of the earth's core

    NASA Technical Reports Server (NTRS)

    Stevenson, D. J.

    1981-01-01

    Combined inferences from seismology, high-pressure experiment and theory, geomagnetism, fluid dynamics, and current views of terrestrial planetary evolution lead to models of the earth's core with five basic properties. These are that core formation was contemporaneous with earth accretion; the core is not in chemical equilibrium with the mantle; the outer core is a fluid iron alloy containing significant quantities of lighter elements and is probably almost adiabatic and compositionally uniform; the more iron-rich inner solid core is a consequence of partial freezing of the outer core, and the energy release from this process sustains the earth's magnetic field; and the thermodynamic properties of the core are well constrained by the application of liquid-state theory to seismic and labroatory data.

  1. Models of the earth's core

    NASA Technical Reports Server (NTRS)

    Stevenson, D. J.

    1981-01-01

    Combined inferences from seismology, high-pressure experiment and theory, geomagnetism, fluid dynamics, and current views of terrestrial planetary evolution lead to models of the earth's core with five basic properties. These are that core formation was contemporaneous with earth accretion; the core is not in chemical equilibrium with the mantle; the outer core is a fluid iron alloy containing significant quantities of lighter elements and is probably almost adiabatic and compositionally uniform; the more iron-rich inner solid core is a consequence of partial freezing of the outer core, and the energy release from this process sustains the earth's magnetic field; and the thermodynamic properties of the core are well constrained by the application of liquid-state theory to seismic and labroatory data.

  2. Models of the Earth's Core.

    PubMed

    Stevenson, D J

    1981-11-06

    Combined inferences from seismology, high-pressure experiment and theory, geomagnetism, fluid dynamics, and current views of terrestrial planetary evolution lead to models of the earth's core with the following properties. Core formation was contemporaneous with earth accretion; the core is not in chemical equilibrium with the mantle; the outer core is a fluid iron alloy containing significant quantities of lighter elements and is probably almost adiabatic and compositionally uniform; the more iron-rich inner solid core is a consequence of partial freezing of the outer core, and the energy release from this process sustains the earth's magnetic field; and the thermodynamic properties of the core are well constrained by the application of liquid-state theory to seismic and laboratory data.

  3. NEUTRONIC REACTOR CORE

    DOEpatents

    Thomson, W.B.; Corbin, A. Jr.

    1961-07-18

    An improved core for a gas-cooled power reactor which admits gas coolant at high temperatures while affording strong integral supporting structure and efficient moderation of neutrons is described. The multiplicities of fuel elements constituting the critical amassment of fissionable material are supported and confined by a matrix of metallic structure which is interspersed therebetween. Thermal insulation is interposed between substantially all of the metallic matrix and the fuel elements; the insulation then defines the principal conduit system for conducting the coolant gas in heat-transfer relationship with the fuel elements. The metallic matrix itseif comprises a system of ducts through which an externally-cooled hydrogeneous liquid, such as water, is circulated to serve as the principal neutron moderant for the core and conjointly as the principal coolant for the insulated metallic structure. In this way, use of substantially neutron transparent metals, such as aluminum, becomes possible for the supporting structure, despite the high temperatures of the proximate gas. The Aircraft Nuclear Propulsion program's "R-1" reactor design is a preferred embodiment.

  4. Plasma core reactor applications

    NASA Technical Reports Server (NTRS)

    Latham, T. S.; Rodgers, R. J.

    1976-01-01

    Analytical and experimental investigations were conducted to demonstrate the feasibility of fissioning uranium plasma core reactors and to characterize space and terrestrial applications for such reactors. Uranium hexafluoride fuel is injected into core cavities and confined away from the surface by argon buffer gas injected tangentially from the peripheral walls. Radiant heat transfer calculations were performed for a six-cavity reactor configuration. Axial working fluid channels are located along a fraction of each cavity peripheral wall. Results of calculations for outward-directed radiant energy fluxes corresponding to radiating temperatures of 2000 to 5000 K indicate total operating pressures from 80 to 650 atm, centerline temperatures from 6900 to 30,000 K, and total radiated powers from 25 to 2500 MW, respectively. Applications are described for this type of reactor such as (1) high-thrust, high specific impulse space propulsion, (2) highly efficient systems for generation of electricity, and (3) hydrogen or synthetic fuel production systems using the intense radiant energy fluxes.

  5. Plasma core reactor applications

    NASA Technical Reports Server (NTRS)

    Latham, T. S.; Rodgers, R. J.

    1976-01-01

    Analytical and experimental investigations were conducted to demonstrate the feasibility of fissioning uranium plasma core reactors and to characterize space and terrestrial applications for such reactors. Uranium hexafluoride fuel is injected into core cavities and confined away from the surface by argon buffer gas injected tangentially from the peripheral walls. Radiant heat transfer calculations were performed for a six-cavity reactor configuration. Axial working fluid channels are located along a fraction of each cavity peripheral wall. Results of calculations for outward-directed radiant energy fluxes corresponding to radiating temperatures of 2000 to 5000 K indicate total operating pressures from 80 to 650 atm, centerline temperatures from 6900 to 30,000 K, and total radiated powers from 25 to 2500 MW, respectively. Applications are described for this type of reactor such as (1) high-thrust, high specific impulse space propulsion, (2) highly efficient systems for generation of electricity, and (3) hydrogen or synthetic fuel production systems using the intense radiant energy fluxes.

  6. GPM Core Observatory

    NASA Image and Video Library

    2017-09-27

    NASA engineers Rob Gallagher (left), Ken Smith (right) and Deneen Ferro (inside the spacecraft, center) work on the Global Precipitation Measurement mission's Core satellite in the clean room at Goddard Space Flight Center, Greenbelt Md. Credit: NASA/GSFC/Rebecca Roth The Global Precipitation Measurement (GPM) mission is an international partnership co-led by NASA and the Japan Aerospace Exploration Agency (JAXA) that will provide next-generation global observations of precipitation from space. GPM will study global rain, snow and ice to better understand our climate, weather, and hydrometeorological processes. As of Novermber 2013 the GPM Core Observatory is in the final stages of testing at NASA Goddard Space Flight Center. The satellite will be flown to Japan in the fall of 2013 and launched into orbit on an HII-A rocket in early 2014. For more on the GPM mission, visit gpm.gsfc.nasa.gov/. NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

  7. Mercury's inner core size and core crystallization regime

    NASA Astrophysics Data System (ADS)

    Dumberry, Mathieu; Rivoldini, Attilio

    2015-04-01

    Earth-based radar observation of Mercury's rotation vector combined with gravity observation by the MESSENGER spacecraft yield a measure of Mercury's moment of inertia and the amplitude of the 88-day libration of its silicate shell. These two geodetic constraints provide information on Mercury's interior structure, including the presence of a fluid core, the radius of the core-mantle boundary and the bulk densities of the core and mantle. In this work, we show how they further provide information on the size of the solid inner core and on the crystallization regime of the fluid core. If Mercury's fluid core is a Fe-FeS alloy, the largest inner core compatible with geodetic observations is 1325 ± 250 km. The crystallization scenario that best fits the observations involves the formation of Fe-snow within the fluid core. Snow formation can be restricted to a thin layer or can occupy the whole of the fluid core depending on inner core size and initial sulfur concentration. Our results offer important constraints for dynamo models of Mercury, but also advocate for the further development of models that incorporate the various features of snow formation.

  8. Assessment of Biasi and Columbia University CHF correlations with GE 3x3 rod bundle experiment. [PWR; BWR

    SciTech Connect

    Chen, B.C.J.; Chien, T.H.; Sha, W.T.; Kim, J.H.

    1984-01-01

    The critical heat flux (CHF), at which a sudden degradation of heat transfer occurs without corresponding decrease in heat generation, is one of the limiting parameters for safe operation of nuclear reactors. Reactor operation beyond the CHF causes a rapid rise in fuel cladding temperature and thus should be avoided to maintain the fuel element integrity. Reactor power limits are therefore set so that a prescribed safety margin below the CHF is maintained. Two CHF correlations are evaluated for reactor core thermal hydraulic analysis: the Biasi correlation and the Columbia University correlation. The BODYFIT-2PE computer code is used for this assessment. The CHF predicted by the BODYFIT-2PE using the two correlations is compared with GE 3x3 rod bundle CHF experiment.

  9. The effect of hydrazine dosing on high temperature pH{sub T} and redox potentials under PWR environments

    SciTech Connect

    Maekelae, K.; Aaltonen, P.; Buddas, T.

    1995-10-01

    The release and deposit of corrosion products, which play a key role in activity transport, are controlled by the properties of the primary water and oxides present on component surfaces. Some of the VVER 440 type reactors have started to use hydrazine dosing to primary coolant instead of ammonia, because it has been shown to be efficient in reducing activity transport. On the other hand, some other studies have shown that there is no significant difference between new VVER units using hydrazine dosing and the ones operating with standard potassium/ammonia water chemistry. In this paper the results are presented concerning the out-of-core high temperature water chemistry and incore redox potential measurements at Rez research reactor in Czech Republic during hydrazine/ammonia water chemistries.

  10. Core drill and method of removing a core therefrom

    SciTech Connect

    Bossler, J.

    1987-04-14

    This patent describes a method of expediting the removal of a core from the interior of a tubular core drill which comprises: fixedly securing an externally threaded bushing to the rear end of the core drill; providing a sleeve for detachably coupling the bushing-equipped core drill to the externally threaded drive shank of a power unit for the core drill. The coupling sleeve is threaded internally of the opposite ends thereof and respectively sized to mate one with the threaded bushing and one with the threaded drive shank; providing the sleeve with wrench engaging means for the assembly and disassembly thereof to and from the drive shank; and detaching the sleeve from the drive shank and withdrawing by gravity a core through the rear end of the drill stem and coupling sleeve.

  11. HTTF Core Stress Analysis

    SciTech Connect

    Brian D. Hawkes; Richard Schultz

    2012-07-01

    In accordance with the need to determine whether cracking of the ceramic core disks which will be constructed and used in the High Temperature Test Facility (HTTF) for heatup and cooldown experiments, a set of calculation were performed using Abaqus to investigate the thermal stresses levels and likelihood for cracking. The calculations showed that using the material properties provided for the Greencast 94F ceramic, cracking is predicted to occur. However, this modeling does not predict the size or length of the actual cracks. It is quite likely that cracks will be narrow with rough walls which would impede the flow of coolant gases entering the cracks. Based on data recorded at Oregon State University using Greencast 94F samples that were heated and cooled at prescribed rates, it was concluded that the likelihood that the cracks would be detrimental to the experimental objectives is small.

  12. NEUTRONIC REACTOR CORE INSTRUMENT

    DOEpatents

    Mims, L.S.

    1961-08-22

    A multi-purpose instrument for measuring neutron flux, coolant flow rate, and coolant temperature in a nuclear reactor is described. The device consists essentially of a hollow thimble containing a heat conducting element protruding from the inner wall, the element containing on its innermost end an amount of fissionsble materinl to function as a heat source when subjected to neutron flux irradiation. Thermocouple type temperature sensing means are placed on the heat conducting element adjacent the fissionable material and at a point spaced therefrom, and at a point on the thimble which is in contact with the coolant fluid. The temperature differentials measured between the thermocouples are determinative of the neutron flux, coolant flow, and temperature being measured. The device may be utilized as a probe or may be incorporated in a reactor core. (AE C)

  13. Growth outside the core.

    PubMed

    Zook, Chris; Allen, James

    2003-12-01

    Growth in an adjacent market is tougher than it looks; three-quarters of the time, the effort fails. But companies can change those odds dramatically. Results from a five-year study of corporate growth conducted by Bain & Company reveal that adjacency expansion succeeds only when built around strong core businesses that have the potential to become market leaders. And the best place to look for adjacency opportunities is inside a company's strongest customers. The study also found that the most successful companies were able to consistently, profitably outgrow their rivals by developing a formula for pushing out the boundaries of their core businesses in predictable, repeatable ways. Companies use their repeatability formulas to expand into any number of adjacencies. Some companies make repeated geographic moves, as Vodafone has done in expanding from one geographic market to another over the past 13 years, building revenues from $1 billion in 1990 to $48 billion in 2003. Others apply a superior business model to new segments. Dell, for example, has repeatedly adapted its direct-to-customer model to new customer segments and new product categories. In other cases, companies develop hybrid approaches. Nike executed a series of different types of adjacency moves: it expanded into adjacent customer segments, introduced new products, developed new distribution channels, and then moved into adjacent geographic markets. The successful repeaters in the study had two common characteristics. First, they were extraordinarily disciplined, applying rigorous screens before they made an adjacency move. This discipline paid off in the form of learning curve benefits, increased speed, and lower complexity. And second, in almost all cases, they developed their repeatable formulas by studying their customers and their customers' economics very, very carefully.

  14. Core body temperature in obesity.

    PubMed

    Heikens, Marc J; Gorbach, Alexander M; Eden, Henry S; Savastano, David M; Chen, Kong Y; Skarulis, Monica C; Yanovski, Jack A

    2011-05-01

    A lower core body temperature set point has been suggested to be a factor that could potentially predispose humans to develop obesity. We tested the hypothesis that obese individuals have lower core temperatures than those in normal-weight individuals. In study 1, nonobese [body mass index (BMI; in kg/m(2)) <30] and obese (BMI ≥30) adults swallowed wireless core temperature-sensing capsules, and we measured core temperatures continuously for 24 h. In study 2, normal-weight (BMI of 18-25) and obese subjects swallowed temperature-sensing capsules to measure core temperatures continuously for ≥48 h and kept activity logs. We constructed daily, 24-h core temperature profiles for analysis. Mean (±SE) daily core body temperature did not differ significantly between the 35 nonobese and 46 obese subjects (36.92 ± 0.03°C compared with 36.89 ± 0.03°C; P = 0.44). Core temperature 24-h profiles did not differ significantly between 11 normal-weight and 19 obese subjects (P = 0.274). Women had a mean core body temperature ≈0.23°C greater than that of men (36.99 ± 0.03°C compared with 36.76 ± 0.03°C; P < 0.0001). Obesity is not generally associated with a reduced core body temperature. It may be necessary to study individuals with function-altering mutations in core temperature-regulating genes to determine whether differences in the core body temperature set point affect the regulation of human body weight. These trials were registered at clinicaltrials.gov as NCT00428987 and NCT00266500.

  15. Stabilization of lunar core samples

    NASA Technical Reports Server (NTRS)

    Nagle, J. S.; Duke, M. B.

    1974-01-01

    Processing of lunar cores includes: (1) careful dissection for study of loose fines, and (2) stabilization of the residue by peeling and impregnation. The newly developed technique for preparing thin peels of lunar cores requires application of the methacrylate adhesive to a backing strip, before taking the peel. To ensure complete impregnation of the very fine, dry lunar soil, the low-viscosity epoxy, Araldite 506, is gently flowed onto the core, under vacuum.

  16. GPM Core Observatory Launch Animation

    NASA Image and Video Library

    This animation depicts the launch of the Global Precipitation Measurement (GPM) Core Observatory satellite from Tanegashima Space Center, Japan. The launch is currently scheduled for Feb. 27, 2014....

  17. A Core Curriculum and Core Curriculum Guide for English III.

    ERIC Educational Resources Information Center

    Haislip, Susan T.

    A practicum project developed the core curriculum and core curriculum guide for an American literature survey course. Students enrolled in the course came from low socioeconomic backgrounds, exhibited problematic behavior, and evidenced poor study habits, as well as low reading comprehension skills and substandard language usage. Under these…

  18. Relativistic frozen core potential scheme with relaxation of core electrons

    NASA Astrophysics Data System (ADS)

    Nakajima, Yuya; Seino, Junji; Hayami, Masao; Nakai, Hiromi

    2016-10-01

    This letter proposes a relaxation scheme for core electrons based on the frozen core potential method at the infinite-order Douglas-Kroll-Hess level, called FCP-CR. The core electrons are self-consistently relaxed using frozen molecular valence potentials after the valence SCF calculation is performed. The efficiency of FCP-CR is confirmed by calculations of gold clusters. Furthermore, FCP-CR reproduces the results of the all-electron method for the energies of coinage metal dimers and the core ionization energies and core level shifts of vinyl acetate and three tungsten complexes at the Hartree-Fock and/or symmetry-adapted cluster configuration interaction levels.

  19. Dissolution experiments of commercial PWR (52 MWd/kgU) and BWR (53 MWd/kgU) spent nuclear fuel cladded segments in bicarbonate water under oxidizing conditions. Experimental determination of matrix and instant release fraction

    NASA Astrophysics Data System (ADS)

    González-Robles, E.; Serrano-Purroy, D.; Sureda, R.; Casas, I.; de Pablo, J.

    2015-10-01

    The denominated instant release fraction (IRF) is considered in performance assessment (PA) exercises to govern the dose that could arise from the repository. A conservative definition of IRF comprises the total inventory of radionuclides located in the gap, fractures, and the grain boundaries and, if present, in the high burn-up structure (HBS). The values calculated from this theoretical approach correspond to an upper limit that likely does not correspond to what it will be expected to be instantaneously released in the real system. Trying to ascertain this IRF from an experimental point of view, static leaching experiments have been carried out with two commercial UO2 spent nuclear fuels (SNF): one from a pressurized water reactor (PWR), labelled PWR, with an average burn-up (BU) of 52 MWd/kgU and fission gas release (FGR) of 23.1%, and one from a boiling water reactor (BWR), labelled BWR, with an average BU of and 53 MWd/kgU and FGR of 3.9%. One sample of each SNF, consisting of fuel and cladding, has been leached in bicarbonate water during one year under oxidizing conditions at room temperature (25 ± 5)°C. The behaviour of the concentration measured in solution can be divided in two according to the release rate. All radionuclides presented an initial release rate that after some days levels down to a slower second one, which remains constant until the end of the experiment. Cumulative fraction of inventory in aqueous phase (FIAPc) values has been calculated. Results show faster release in the case of the PWR SNF. In both cases Np, Pu, Am, Cm, Y, Tc, La and Nd dissolve congruently with U, while dissolution of Zr, Ru and Rh is slower. Rb, Sr, Cs and Mo, dissolve faster than U. The IRF of Cs at 10 and 200 days has been calculated, being (3.10 ± 0.62) and (3.66 ± 0.73) for PWR fuel, and (0.35 ± 0.07) and (0.51 ± 0.10) for BWR fuel.

  20. Comet whole-core solution to a stylized 3-dimensional pressurized water reactor benchmark problem with UO{sub 2}and MOX fuel

    SciTech Connect

    Zhang, D.; Rahnema, F.

    2012-07-01

    A stylized pressurized water reactor (PWR) benchmark problem with UO{sub 2} and MOX fuel was used to test the accuracy and efficiency of the coarse mesh radiation transport (COMET) code. The benchmark problem contains 125 fuel assemblies and 44,000 fuel pins. The COMET code was used to compute the core eigenvalue and assembly and pin power distributions for three core configurations. In these calculations, a set of tensor products of orthogonal polynomials were used to expand the neutron angular phase space distribution on the interfaces between coarse meshes. The COMET calculations were compared with the Monte Carlo code MCNP reference solutions using a recently published an 8-group material cross section library. The comparison showed both the core eigenvalues and assembly and pin power distributions predicated by COMET agree very well with the MCNP reference solution if the orders of the angular flux expansion in the two spatial variables and the polar and azimuth angles on the mesh boundaries are 4, 4, 2 and 2. The mean and maximum differences in the pin fission density distribution ranged from 0.28%-0.44% and 3.0%-5.5%, all within 3-sigma uncertainty of the MCNP solution. These comparisons indicate that COMET can achieve accuracy comparable to Monte Carlo. It was also found that COMET's computational speed is 450 times faster than MCNP. (authors)