Science.gov

Sample records for a-570-601 tapered roller

  1. Development of small bore, high speed tapered roller bearing

    NASA Technical Reports Server (NTRS)

    Morrison, F. R.; Gassel, S. S.; Bovenkerk, R. L.

    1981-01-01

    The performance of four rolling bearing configurations for use on the input pinion shaft of a proposed commercial helicopter transmission was evaluated. The performance characteristics of a high speed tapered roller bearing operating under conditions comparable to those existing at this input pinion shaft were defined. The tapered roller bearing shaft support configuration was developed for the gearbox using commercially available bearing designings. The configuration was optimized and interactive thermomechanically system analyzed. Automotive pinion quality tapered roller bearings were found to be reliable under load and speed conditions in excess of those anticipated in the helicopter transmission. However, it is indicated that the elastohydrodynamic lubricant films are inadequate.

  2. Temperature distribution and scuffing of tapered roller bearing

    NASA Astrophysics Data System (ADS)

    Wang, Ailin; Wang, Jiugen

    2014-11-01

    In the field of aerospace, high-speed trains and automobile, etc, analysis of temperature filed and scuffing failure of tapered roller bearings are more important than ever, and the scuffing failure of elements of such rolling bearings under heavy load and high speed still cannot be effectively predicted yet. A simplified model of tapered roller bearings consisted of one inner raceway, one outer raceway and a tapered roller was established, in which the interaction of several heat sources is ignored. The contact mechanics model, temperature model and model of scuffing failure are synthesized, and the corresponding computer programs are developed to analyze the effects of bearings parameters, different material and operational conditions on thermal performance of bearings, and temperature distribution and the possibility of surface scuffing are obtained. The results show that load, speed, thermal conductivity and tapered roller materials influence temperature rise and scuffing failure of bearings. Ceramic material of tapered roller results in the decrease of scuffing possibility of bearings to a high extent than the conventional rolling bearing steel. Compared with bulk temperature, flash temperature on the surfaces of bearing elements has a little influence on maximum temperature rise of bearing elements. For the rolling bearings operated under high speed and heavy load, this paper proposes a method which can accurately calculate the possibility of scuffing failure of rolling bearings.

  3. Tapered Roller Bearing Damage Detection Using Decision Fusion Analysis

    NASA Technical Reports Server (NTRS)

    Dempsey, Paula J.; Kreider, Gary; Fichter, Thomas

    2006-01-01

    A diagnostic tool was developed for detecting fatigue damage of tapered roller bearings. Tapered roller bearings are used in helicopter transmissions and have potential for use in high bypass advanced gas turbine aircraft engines. A diagnostic tool was developed and evaluated experimentally by collecting oil debris data from failure progression tests conducted using health monitoring hardware. Failure progression tests were performed with tapered roller bearings under simulated engine load conditions. Tests were performed on one healthy bearing and three pre-damaged bearings. During each test, data from an on-line, in-line, inductance type oil debris sensor and three accelerometers were monitored and recorded for the occurrence of bearing failure. The bearing was removed and inspected periodically for damage progression throughout testing. Using data fusion techniques, two different monitoring technologies, oil debris analysis and vibration, were integrated into a health monitoring system for detecting bearing surface fatigue pitting damage. The data fusion diagnostic tool was evaluated during bearing failure progression tests under simulated engine load conditions. This integrated system showed improved detection of fatigue damage and health assessment of the tapered roller bearings as compared to using individual health monitoring technologies.

  4. Improved oil-off survivability of tapered roller bearings

    NASA Technical Reports Server (NTRS)

    Kreider, Gary E.; Lee, Peter W.

    1987-01-01

    The aim of this program is to improve the oil-off survivability of a tapered roller bearing when applied to a helicopter transmission, since the tapered bearing has shown a performance advantage in this application. However, the critical roller end-rib conjunction is vulnerable to damage in an oil-off condition. Three powdered metal materials were selected to use as the rib material for oil-off evaluation. These were: M2 steel to a 65% density, CBS 1000M 65% density, and CBS 1000M 75% density. The bearing styles tested were ribbed cone (inner race) and ribbed cup (outer race). Carburized solid CBS 600 was also used as a ribbed material for comparison of oil-off results. The tests were conducted at six speeds from 4000 rpm (0.26 million DN) through 37000 rpm (2.4 million DN).The ribbed cup style bearing achieved longer lives than the ribbed cone style. A standard bearing lasted only 10 minutes at 4000 rpm; however, the 30-min oil-off goal was achieved through 11000 rpm using the survivable ribbed cup bearing. The oil-off lives at 37000 rpm were less than 10 seconds. The grinding of the powder metal materials and surface preparation to achieve an open porosity is extremely critical to the oil-off performance of the powder metal component.

  5. 76 FR 6397 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-02-04

    ... China, 52 FR 22667 (June 15, 1987) (``Order''). On December 23, 2010, pursuant to section 751(a)(2)(B)(i... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the... shipper review (``NSR'') of the antidumping duty order on tapered roller bearings (``TRBs'') from...

  6. 76 FR 45777 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-01

    ... China, 52 FR 22667 (June 15, 1987) (``Order''). On June 30, 2011, pursuant to section 751(a)(2)(B)(i) of... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the... review (``NSR'') of the antidumping duty order on tapered roller bearings (``TRBs'') from the...

  7. 77 FR 45588 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-01

    ... Republic of China, 52 FR 22667 (June 15, 1987) (``Order''). \\2\\ See 19 CFR 351.214(d). In its submission... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the... on tapered roller bearings from the People's Republic of China (``PRC'') meets the statutory...

  8. 77 FR 45587 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, from the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-01

    ... Republic of China, 52 FR 22667 (June 15, 1987) (``Order''). \\2\\ See 19 CFR 351.214(d). In its submission... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, from the... on tapered roller bearings (``TRBs'') from the People's Republic of China (``PRC'') meets...

  9. 77 FR 16859 - Tapered Roller Bearings From China; Scheduling of a Full Five-Year Review

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-22

    ... that a full review pursuant to section 751(c)(5) of the Act should proceed (76 FR 72213, November 22... amended. The amendments took effect on November 7, 2011. See 76 FR 61937 (Oct. 6, 2011) and the newly... COMMISSION Tapered Roller Bearings From China; Scheduling of a Full Five- Year Review AGENCY: United...

  10. 77 FR 12326 - Tapered Roller Bearings From China; Scheduling of a Full Five-Year Review

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-29

    ... to section 751(c)(5) of the Act should proceed (76 FR 72213, November 22, 2011). A record of the... amendments took effect on November 7, 2011. See 76 FR 61937 (Oct. 6, 2011) and the newly revised Commission's... COMMISSION Tapered Roller Bearings From China; Scheduling of a Full Five- Year Review AGENCY: United...

  11. Investigation of Tapered Roller Bearing Damage Detection Using Oil Debris Analysis

    NASA Technical Reports Server (NTRS)

    Dempsey, Paula J.; Krieder, Gary; Fichter, Thomas

    2006-01-01

    A diagnostic tool was developed for detecting fatigue damage to tapered roller bearings. Tapered roller bearings are used in helicopter transmissions and have potential for use in high bypass advanced gas turbine aircraft engines. This diagnostic tool was developed and evaluated experimentally by collecting oil debris data from failure progression tests performed by The Timken Company in their Tapered Roller Bearing Health Monitoring Test Rig. Failure progression tests were performed under simulated engine load conditions. Tests were performed on one healthy bearing and three predamaged bearings. During each test, data from an on-line, in-line, inductance type oil debris sensor was monitored and recorded for the occurrence of debris generated during failure of the bearing. The bearing was removed periodically for inspection throughout the failure progression tests. Results indicate the accumulated oil debris mass is a good predictor of damage on tapered roller bearings. The use of a fuzzy logic model to enable an easily interpreted diagnostic metric was proposed and demonstrated.

  12. Lubrication of high-speed, large bore tapered-roller bearings

    NASA Technical Reports Server (NTRS)

    Parker, R. J.; Signer, H. R.

    1977-01-01

    The performance of 120.65-mm- (4.75-in.-) bore tapered-roller bearings was investigated at shaft speeds up to 15,000 rpm (18,000 DN). Temperature distribution and bearing heat generation were determined as a function of shaft speed, radial and thrust loads, lubricant flow rate, and lubricant inlet temperature. Lubricant was supplied either by jets or by a combination of holes through the cone directly to the cone-rib contact and jets at the roller small-end side. Cone-rib lubrication significantly improved high-speed tapered-roller bearing performance, yielding lower cone-face temperatures and lower power loss and allowing lower lubricant flow rates for a given speed condition. Bearing temperatures increased with increased shaft speed and decreased with increased lubricant flow rate. Bearing power loss increased with increased shaft speed and increased lubricant flow rate.

  13. Large-bore tapered-roller bearing performance and endurance to 2.4 million DN

    NASA Technical Reports Server (NTRS)

    Parker, R. J.

    1983-01-01

    The operating characteristics and experimental life estimates for 120.65 mm bore tapered roller bearings of two designs under combined radial and thrust loads were determined. A modified standard bearing design was tested at speeds up to 15,000 rpm. A computer optimized, high speed design was tested at speeds up to 20,000 rpm. Both designs were tested at a combined load of 26,700 N (6000 lb) radial load and and 53,400 N (12,000 lb) thrust load. Advanced helicopter transmissions which require the higher-speed capability of tapered-roller bearings also require higher temperature capability (ref. 2). Thus, materials with temperature capabilities higher than the conventional carburizing steels are required.

  14. Dynamic and thermal analysis of high speed tapered roller bearings under combined loading

    NASA Technical Reports Server (NTRS)

    Crecelius, W. J.; Milke, D. R.

    1973-01-01

    The development of a computer program capable of predicting the thermal and kinetic performance of high-speed tapered roller bearings operating with fluid lubrication under applied axial, radial and moment loading (five degrees of freedom) is detailed. Various methods of applying lubrication can be considered as well as changes in bearing internal geometry which occur as the bearing is brought to operating speeds, loads and temperatures.

  15. 76 FR 43262 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-20

    ...: Initiation of Antidumping Duty New Shipper Review, 76 FR 6397 (February 4, 2011). On June 17, 2011, the... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the... (``NSR'') of Xiang Yang Automobile Bearing Co., Ltd. (``ZXY'').\\1\\ We gave interested parties...

  16. 76 FR 72213 - Tapered Roller Bearings From China; Notice of Commission determination To Conduct a Full Five...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-22

    ... part 201), and part 207, subparts A, D, E, and F (19 CFR part 207), as amended, 76 FR 61937 (October 6... responses to its notice of institution (76 FR 45853, August 1, 2011) were adequate.\\2\\ A record of the... COMMISSION Tapered Roller Bearings From China; Notice of Commission determination To Conduct a Full...

  17. 78 FR 45912 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-30

    ... the People's Republic of China, 52 FR 22667 (June 15, 1987). \\2\\ See Antidumping or Countervailing Duty Order, Finding, or Suspended Investigation; Opportunity to Request Administrative Review, 78 FR... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From...

  18. 77 FR 52682 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-30

    ... (Third Review), USITC Publication 4343 (August 2012), and Tapered Roller Bearings From China, 77 FR 50716... Act of 1930, as amended (``Act'').\\1\\ \\1\\ See Initiation of Five-Year (``Sunset'') Review, 76 FR 45778... Antidumping Duty Order, 76 FR 76143 (December 6, 2011). On July 31, 2012, the ITC determined, pursuant...

  19. 78 FR 38943 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-28

    ... Parts Thereof, Finished or Unfinished, From the People's Republic of China, 52 FR 22667 (June 15, 1987... Antidumping Duty Order, 62 FR 6189 (Feb. 11, 1997). Effective August 1, 2012, the majority shareholder of SGBC... International Trade Administration Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From...

  20. 76 FR 76143 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-06

    ... Republic of China, 52 FR 22667 (June 15, 1987), as amended, Tapered Roller Bearings From the People's... Order in Accordance With Decision Upon Remand, 55 FR 6669 (Feb. 26, 1990) (``Order''). As a result of...'') Review, 76 FR 45778, 45779 (August 1, 2011) (``Sunset Initiation''). On August 16, 2011, the...

  1. Performance tests with a 4.75 inch bore tapered-roller bearings at high speeds

    NASA Technical Reports Server (NTRS)

    Signer, H. R.; Pinel, S. I.

    1977-01-01

    The tapered-roller bearings were tested at speeds to 15,000 rpm which results in a cone-rib tangential velocity of 130 m/sec. (25,500 ft/min). Lubrication was applied either by jets or directly to the cone-rib, augmented with jets. Additional test parameters included thrust loads to 53,400 N (12,000 lbs), radial loads to 26,700 N (6,000 lbs), lubricant flow rates from 1.9 x 0.000 to 15.1 x 0.001 cubic meter/min. (0.5 to 4.0 gpm), and lubricant inlet temperatures of 350 K and 364 K (170 F and 195 F). Temperature distribution, separator speed, and drive-motor power demand were determined as functions of these test parameters.

  2. Performance of large-bore tapered-roller bearings under combined radial and thrust load at shaft speeds to 15,000 rpm

    NASA Technical Reports Server (NTRS)

    Parker, R. J.; Signer, H. R.

    1977-01-01

    The performance of 120.65-mm bore tapered roller bearings was investigated at shaft speeds up to 15,000 rpm. Temperature distribution and bearing heat generation were determined as a function of shaft speed, radial and thrust loads, lubricant flow rate, and lubricant inlet temperature. Lubricant was supplied by either jets or by a combination of holes through the cone directly to the cone-rib contact and jets at the roller small-end side. Cone-rib lubrication significantly improved high-speed tapered-roller bearing performance, yielding lower cone-face temperatures and lower power loss and allowing lower lubricant flow rates for a given speed condition. Bearing temperatures increased with increased shaft speed and decreased with increased lubricant flow rate. Bearing power loss increased with increased shaft speed and increased lubricant flow rate.

  3. Effect of roller shapes on strip buckling in a continuous annealing furnace

    NASA Astrophysics Data System (ADS)

    Yang, Jing; Tang, Di; Su, Lan; Jiang, Hai-Tao; Yang, Quan

    2011-06-01

    The effect of roller shapes on strip buckling in a continuous annealing furnace was focused on. The tensile stress distribution, the transverse compressive stress, and the critical buckling stress of the strip were studied by the finite element method (FEM) when the flat roller, crown roller, single taper roller, and double taper roller were used, respectively. Simulation results show that strip buckling is most likely to occur with the crown roller, then the double taper roller, and finally the single taper roller. Also, strip buckling can not occur when the flat roller is used. Considering strip snaking, the single taper roller and double taper roller are suggested in the continuous annealing furnace. The double taper roller with a better strip snaking-prevention ability should be applied in the sections with high strip temperature, and the single taper roller with a better buckling-prevention ability should be used in the sections with low strip temperature.

  4. Research report: User's manual for computer program AT81y003 SHABERTH. Steady state and transient thermal analysis of a shaft bearing system including ball, cylindrical and tapered roller bearings

    NASA Technical Reports Server (NTRS)

    Hadden, G. B.; Kleckner, R. J.; Ragen, M. A.; Sheynin, L.

    1981-01-01

    The SHABERTH program is capable of simulating the thermomechanical performance of a load support system consisting of a flexible shaft supported by up to five rolling element bearings. Any combination of ball, cylindrical, and tapered roller bearings can be used to support the shaft. The user can select models in calculating lubricant film thickness and traction forces. The formulation of the cage pocket/rolling element interaction model was revised to improve solution numerical convergence characteristics.

  5. Kinematic correction for roller skewing

    NASA Technical Reports Server (NTRS)

    Savage, M.; Loewenthal, S. H.

    1980-01-01

    A theory of kinematic stabilization of rolling cylinders is developed for high-speed cylindrical roller bearings. This stabilization requires race and roller crowning to product changes in the rolling geometry as the roller shifts axially. These changes put a reverse skew in the rolling elements by changing the rolling taper. Twelve basic possible bearing modifications are identified in this paper. Four have single transverse convex curvature in the rollers while eight have rollers with compound transverse curvature composed of a central cylindrical band of constant radius surrounded by symmetric bands with both slope and transverse curvature.

  6. Roller Coasters!

    ERIC Educational Resources Information Center

    Ansberry, Karen; Morgan, Emily

    2008-01-01

    Students of all ages are fascinated by the ups, downs, loops, and twists of roller coaster rides! What they may not realize is that there is a lot of science involved in making a roller coaster work. This month's column puts students in the shoes of a roller coaster designer as they work in teams to create their own roller coasters. (Contains 1…

  7. System for automatically aligning a support roller system under a rotating body

    DOEpatents

    Singletary, B.H.

    1982-07-21

    Two support rings on a rotatable drum respectively engage conically tapered end surfaces of support rollers mounted on pivot universally relative to its axis of rotation and translate therealong. Rotation of the drum on differential conical support roller diameters causes pivotal steering and axial translation of support roller until roller is centered on support rings.

  8. System for automatically aligning a support roller system under a rotating body

    DOEpatents

    Singletary, B. Huston

    1983-01-01

    Two support rings on a rotatable drum respectively engage conically tapered nd surfaces of support rollers mounted on pivot universally relative to its axis of rotation and translate therealong. Rotation of the drum on differential conical support roller diameters causes pivotal steering and axial translation of support roller until roller is centered on support rings.

  9. Effect of Roller Profile on Cylindrical Roller Bearing Life Prediction

    NASA Technical Reports Server (NTRS)

    Poplawski, Joseph V.; Zaretsky, Erwin V.; Peters, Steven M.

    2000-01-01

    Four roller profiles used in cylindrical roller bearing design and manufacture were analyzed using both a closed form solution and finite element analysis (FEA) for stress and life. The roller profiles analyzed were flat, tapered end, aerospace, and fully crowned loaded against a flat raceway. Four rolling-element bearing life models were chosen for this analysis and compared. These were those of Weibull, Lundberg and Palmgren, Ioannides and Harris, and Zaretsky. The flat roller profile without edge loading has the longest predicted life. However, edge loading can reduce life by as much as 98 percent. The end tapered profile produced the highest lives but not significantly different than the aerospace profile. The fully crowned profile produces the lowest lives. The resultant predicted life at each stress condition not only depends on the life equation used but also on the Weibull slope assumed. For Weibull slopes of 1.5 and 2, both Lundberg-Palmgren and Iaonnides-Harris equations predict lower lives than the ANSI/ABMAJISO standards. Based upon the Hertz stresses for line contact, the accepted load-life exponent of 10/3 results in a maximum Hertz stress-life exponent equal to 6.6. This value is inconsistent with that experienced in the field.

  10. Roller skewing measurements in cylindrical roller bearings

    NASA Technical Reports Server (NTRS)

    Nypan, L. J.

    1981-01-01

    Measurements of roller skewing in a 118 mm bore roller bearing operating at shaft speeds to 12,000 rpm are reported. High speed motion pictures of a modified roller were taken through a derotation prism to record skewing as the roller moved through loaded and unloaded regions of the bearing. Subsequent frame by frame measurement of the photographic film provided information on roller skewing. Radial and tangential skew amplitudes of 0.4 to 0.5 degrees were observed with 0.5 degree misalignment.

  11. Rollerized timing lifter

    SciTech Connect

    Rhodes, G.E.

    1988-05-03

    A rollerized timing lifter assembly is described comprising: a first tubular roller body sleeve having a top end and a bottom end; a roller; means for mounting the roller on the bottom end of the first tubular roller body sleeve; the first tubular roller body sleeve having an oil collecting channel and an oil feed port hole extending through the first tubular roller body sleeve; a second tubular body with a top end and a closed bottom end that is placed within the first tubular roller body sleeve and engaged telescopically a shoulder at near bottom of the first tubular roller body sleeve; the second tubular body having an external collecting channel positioned around the second tubular body and a second port hole to admit oil through the second tubular body; a hollow cylindrical plunger axially slideable in the second tubular body and enclosing a pressure chamber in the lower end of the second tubular body; a port in the plunger communicating with the first and second mentioned ports to admit oil into the plunger; and a valve in the plunger opening into the pressure chamber and means for receiveably capturing the bottom end of a push rod in a top end of the plunger.

  12. TUBE FLANGING APPARATUS HAVING SPIRAL CAM ACTUATED FLANGING ROLLERS

    DOEpatents

    Bellarts, H.J.

    1958-06-24

    A tube flaring apparatus designed to roll flawless uniform flanges on tube ends suitable for use in a Van Stone joint is described. Tapered rollers are mounted on gear segnnents and placed in the end of the tube. The assembly is rotated axially within the tube, and periodically the gear segments are moved by a worm gear so as to force the rollers radially against the tube wall until eventually a perfect 90 d flange is formed on the tube. All flanges formed by this machine are uniform, stronger, and have fewer possibilities for leaks than conventional methods heretofore used.

  13. Worm drive detail, roller hoist mechanism, rolling crest roller gate ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Worm drive detail, roller hoist mechanism, rolling crest roller gate - plan and sections - Grand Valley Diversion Dam, Half a mile north of intersection of I-70 & Colorado State Route 65, Cameo, Mesa County, CO

  14. EVALUATING A FIBERGLASS ROLLER COVERING ON A ROLLER GIN STAND

    Technology Transfer Automated Retrieval System (TEKTRAN)

    An experimental roller covering, made from woven fiberglass, was tested on a roller gin stand to evaluate its ginning performance and effect on fiber quality. The experimental roller covering was much more aggressive than the standard covering; it ginned at twice the rate (2.4 vs. 1.2 bales per hour...

  15. The World's Best Roller Coasters.

    ERIC Educational Resources Information Center

    Jones, T. Griffith; Jones, Linda Cronin

    1995-01-01

    Constructing model roller coasters is a great way for students to explore concepts related to energy and motion. Describes making a model roller coaster with 4th grade students. Students learn about different forms of energy and answer their own questions about roller coasters. (NB)

  16. Variable loading roller

    DOEpatents

    Williams, D.M.

    1988-01-21

    An automatic loading roller for transmitting torque in traction drive devices in manipulator arm joints includes a two-part camming device having a first cam portion rotatable in place on a shaft by an input torque and a second cam portion coaxially rotatable and translatable having a rotating drive surface thereon for engaging the driven surface of an output roller with a resultant force proportional to the torque transmitted. Complementary helical grooves in the respective cam portions interconnected through ball bearings interacting with those grooves effect the rotation and translation of the second cam portion in response to rotation of the first. 14 figs.

  17. Variable loading roller

    DOEpatents

    Williams, Daniel M.

    1989-01-01

    An automatic loading roller for transmitting torque in traction drive devices in manipulator arm joints includes a two-part camming device having a first cam portion rotatable in place on a shaft by an input torque and a second cam portion coaxially rotatable and translatable having a rotating drive surface thereon for engaging the driven surface of an output roller with a resultant force proportional to the torque transmitted. Complementary helical grooves on the respective cam portions interconnected through ball bearings interacting with those grooves effect the rotation and translation of the second cam portion in response to rotation of the first.

  18. Roller Coaster Science.

    ERIC Educational Resources Information Center

    Sumners, Carolyn; Jones, Howard L.

    1983-01-01

    Discusses the science of roller coasters, relating gravity, potential/kinetic energy, inertia, and centripetal force to the various parts of the ride, providing tips on linking classroom discussions to field trips. Includes sample student activity sheet and source for additional units using amusement park rides/playground activities to teach…

  19. Gearbox Reliability Collaborative High Speed Shaft Tapered Roller Bearing Calibration

    SciTech Connect

    Keller, J.; Guo, Y.; McNiff, B.

    2013-10-01

    The National Renewable Energy Laboratory (NREL) Gearbox Reliability Collaborative (GRC) is a project investigating gearbox reliability primarily through testing and modeling. Previous dynamometer testing focused upon acquiring measurements in the planetary section of the test gearbox. Prior to these tests, the strain gages installed on the planetary bearings were calibrated in a load frame.

  20. 77 FR 50716 - Tapered Roller Bearings From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-22

    ... The Commission instituted this review on August 1, 2011 (76 FR 45853) and determined on November 4, 2011 that it would conduct a full review (76 FR 72213, November 22, 2011). Notice of the scheduling of..., Washington, DC, and by publishing the notice in the Federal Register on February 29, 2012 (77 FR 12326)....

  1. Roller Cam Positioners

    SciTech Connect

    Bowden, Gordon B.

    2010-12-07

    Roller Cam Positioners could support the LCLS undulator sections allowing micron sized alignment adjustment of each undulator in 5 degrees of freedom. The supports are kinematic with the number of degrees of freedom matched to the number of constraints. Ton loads are supported on simple ball bearings. Motion is intrinsically bounded. Positioning mechanisms are based on pure rolling motion with sub-micron hysteresis and micron resolution. This note describes a general purpose positioning mechanism suitable for undulator support.

  2. Parabolic tapers for overmoded waveguides

    DOEpatents

    Doane, J.L.

    1983-11-25

    A waveguide taper with a parabolic profile, in which the distance along the taper axis varies as the square of the tapered dimension, provides less mode conversion than equal length linear tapers and is easier to fabricate than other non-linear tapers.

  3. Roller belleville spring damper

    SciTech Connect

    Hebel, J.B.

    1981-07-07

    A double acting damper for use in rotary drilling includes a splined tubular telescopic joint and employs plural paralleled stacks of double acting series stacked roller belleville spring washers in an annular pocket between the inner and outer tubular members of the joint. The springs, spline and telescopic bearings are in an oil filled volume sealed from the outside by a pressure seal at the lower end of the damper and a floating seal at the upper end. Electric and magnetic means are provided to check on the condition and quantity of the lubricant.

  4. Muscle oxygenation trends after tapering in trained cyclists

    PubMed Central

    Neary, J Patrick; McKenzie, Donald C; Bhambhani, Yagesh N

    2005-01-01

    Background This study examined muscle deoxygenation trends before and after a 7-day taper using non-invasive near infrared spectroscopy (NIRS). Methods Eleven cyclists performed an incremental cycle ergometer test to determine maximal oxygen consumption (VO2max = 4.68 ± 0.57 L·min-1) prior to the study, and then completed two or three high intensity (85–90% VO2max) taper protocols after being randomly assigned to a taper group: T30 (n = 5), T50 (n = 5), or T80 (n = 5) [30%, 50%, 80% reduction in training volume, respectively]. Physiological measurements were recorded during a simulated 20 km time trials (20TT) performed on a set of wind-loaded rollers. Results and Discussion The results showed that the physiological variables of oxygen consumption (VO2), carbon dioxide (VCO2) and heart rate (HR) were not significantly different after tapering, except for a decreased ventilatory equivalent for oxygen (VE/VO2) in T50 (p ≤ 0.05). However, during the 20TT muscle deoxygenation measured continuously in the vastus medialis was significantly lower (-749 ± 324 vs. -1140 ± 465 mV) in T50 after tapering, which was concomitant with a 4.53% improvement (p = 0.057) in 20TT performance time, and a 0.18 L·min-1 (4.5%) increase in VO2. Furthermore, when changes in performance time and tissue deoxygenation (post- minus pre-taper) were plotted (n = 11), a moderately high correlation was found (r = 0.82). Conclusion It was concluded that changes in simulated 20TT performance appeared to be related, in part, to changes in muscle deoxygenation following tapering, and that NIRS can be used effectively to monitor muscle deoxygenation during a taper period. PMID:15790400

  5. Tapered structure construction

    DOEpatents

    Smith, Eric D.; Takata, Rosalind K.; Slocum, Alexander H.; Nayfeh, Samir A.

    2016-04-05

    Feeding stock used to form a tapered structure into a curving device such that each point on the stock undergoes rotational motion about a peak location of the tapered structure; and the stock meets a predecessor portion of stock along one or more adjacent edges.

  6. Roller coaster-induced barotrauma.

    PubMed

    Al-Khudari, Samer; Loochtan, Michael; Yaremchuk, Kathleen

    2011-03-01

    We present the case of a 24-year-old male who presented to the otolaryngology clinic for otalgia and aural fullness after riding a roller coaster. We present his clinical course and outcome and briefly discuss the mechanism of injury and otologic barotrauma. Roller coasters have been reported as the cause of many different types of injuries, but this is the first reported case of otologic barotrauma. As the engineering for roller coasters continues to advance in terms of increasing speed, otolaryngologists need to be aware of a new etiology of otologic barotrauma. PMID:21344425

  7. Tolerance Design of Logarithmic Roller Profiles in Cylindrical Roller Bearings

    NASA Astrophysics Data System (ADS)

    Fujiwara, Hiroki; Yamauchi, Kazuto

    A logarithmic profile is essentially optimal crowning geometry for rolling machine elements such as bearing rollers and raceways. Although some design methods of the profile have been proposed, they do not refer to the tolerance of the geometry required in engineering applications and in production. This paper shows how to define the tolerance range associated with the optimum roller profile, previously suggested by one of the authors. The overall tolerance is reasonably defined by giving the reduced amount of roller radius at three points so that the von Mises equivalent stress will not exceed a specified limit, where the point locations are not measured from the roller end but from the intersection of the crowning and the chamfer. For the purpose of design usefulness, the tolerance expression is offered in dimensionless form.

  8. Roller conveyor for a glass furnace

    SciTech Connect

    Ford, J.; Canfield, D.M.

    1986-08-26

    A furnace is described for heat treatment of glass including annealing, heat strengthening, tempering and bending of glass which comprises: a housing defining an elongated furnace chamber having an inlet and an outlet; a roller conveyor between the inlet and the outlet and including respective rows of stub rollers disposed along each longitudinal side of the housing flanking a path between the inlet and the outlet, a lower row of deflecting rollers below one of the rows of stub rollers with the rollers of the lower row being positioned between the stub rollers of the one row, a drive belt being looped over each stub roller of the one row and under each roller of the lower row therebetween, the stub rollers each being provided with at least one band of a heat resistant elastomeric material coating at least a portion of the surface thereof; fused silica support rollers spanning the conveyor with each support roller exclusively upon the respective bands of two stub rollers on each side of the housing, the bands being positioned relative to the belt so as to hold the fused silica support rollers out of engagement with the respective belt; means for driving the belt to oscillate glass objects carried by the support rollers back and forth in the housing; and an array of infrared heaters mounted in the housing at least above the conveyor.

  9. Tapered GRIN fiber microsensor.

    PubMed

    Beltrán-Mejía, Felipe; Biazoli, Claudecir R; Cordeiro, Cristiano M B

    2014-12-15

    The sensitivity of an optical fiber microsensor based on inter-modal interference can be considerably improved by tapering a short extension of the multimode fiber. In the case of Graded Index fibers with a parabolic refractive index profile, a meridional ray exhibits a sinusoidal path. When these fibers are tapered, the period of the propagated beam decrease down-taper and increase up-taper. We take advantage of this modulation -along with the enhanced overlap between the evanescent field and the external medium- to substantially increase the sensitivity of these devices by tuning the sensor's maximum sensitivity wavelength. Moreover, the extension of this device is reduced by one order of magnitude, making it more propitious for reduced space applications. Numerical and experimental results demonstrate the success and feasibility of this approach. PMID:25606989

  10. Tapered, tubular polyester fabric

    NASA Technical Reports Server (NTRS)

    Lapointe, Donat J. E. (Inventor); Wright, Lawrence T. (Inventor); Vincent, Laurence J. (Inventor)

    1987-01-01

    A tapered tubular polyester sleeve is described to serve as the flexible foundation for a spacesuit limb covering. The tube has a large end and a small end with a length to be determined. The ratio of taper is also determined by scale factors. All the warp yarns extend to the large end. A requisite number of warp yarns extend the full length of the sleeve. Other warp yarns extend from the large end but are terminated along the length of the sleeve. It is then woven with a filling yarn which extends in a full circle along the full length of the sleeve to thereby define the tapered sleeve. The sleeve after fabrication is then placed on a mandrel, heated in an oven, and then attached to the arm or other limb of the spacesuit.

  11. Tapered, tubular polyester fabric

    NASA Technical Reports Server (NTRS)

    LaPointe, Donat J. E. (Inventor); Vincent, Laurence J. (Inventor); Wright, Lawrence T. (Inventor)

    1988-01-01

    A tapered tubular polyester sleeve as set forth. It has a large end 12 and a small end 14 with a length to be determined. The ratio of taper is also determined by scale factors. All the warp yarns extend to the large end 12. A requisite number of warp yarns 16 extend the full length of the sleeve. Other warp yarns exemplified at 18, 22, 26, 28, 30 and 32 extend from the large end but are terminated along the length of the sleeve. It is then woven with a filling yarn 40 which extends in a full circle along the full length of the sleeve to thereby define the tapered sleeve. The sleeve after fabrication is then placed on a mandrel 42, heated in an oven 44 and is thereafter placed on the arm or other limb of a space suit exemplified at 50.

  12. Stopping a Roller Coaster Train

    ERIC Educational Resources Information Center

    Pendrill, Ann-Marie; Karlsteen, Magnus; Rodjegard, Henrik

    2012-01-01

    A roller coaster ride comes to an end. Magnets on the train induce eddy currents in the braking fins, giving a smooth rise in braking force as the remaining kinetic energy is absorbed by the brakes and converted to thermal energy. In this paper an IR camera was used to monitor the temperature of the first braking fin, before, during and after the…

  13. Compound taper milling machine

    NASA Technical Reports Server (NTRS)

    Campbell, N. R.

    1969-01-01

    Simple, inexpensive milling machine tapers panels from a common apex to a uniform height at panel edge regardless of the panel perimeter configuration. The machine consists of an adjustable angled beam upon which the milling tool moves back and forth above a rotatable table upon which the workpiece is held.

  14. Free-roller versus fixed-roller fixtures in flexure testing of advanced ceramic materials

    SciTech Connect

    Choi, S.R.; Salem, J.A.

    1996-12-31

    The error associated with strength measurements made with fixed-roller and V-grooved roller fixtures was studied with a variety of roller and fixture material combinations. Both the fixed-roller and the V-grooved fixtures yielded an error in stress of about 4 to 7 %. They also exhibited an appreciable amount of load strain hysteresis. Dynamic fatigue testing of 96 wt % alumina verified the error: the fatigue strength was overestimated by 7 to 9 % for the fixed-roller configuration. The source of error is exclusively attributed to friction between the rollers and the specimen surface, as verified by previous investigators.

  15. Effect of Roller Geometry on Roller Bearing Load-Life Relation

    NASA Technical Reports Server (NTRS)

    Oswald, Fred B.; Zaretsky, Erwin V.; Poplawski, Joseph V.

    2015-01-01

    Cylindrical roller bearings typically employ roller profile modification to equalize load distribution, minimize stress concentration at roller ends and allow for a small amount of misalignment. The 1947 Lundberg-Palmgren analysis reported an inverse fourth power relation between load and life for roller bearings with line contact. In 1952, Lundberg and Palmgren changed their load-life exponent to 10/3 for roller bearings, assuming mixed line and point contact. The effect of roller-crown profile was reanalyzed in this paper to determine the actual load-life relation for modified roller profiles. For uncrowned rollers (line contact), the load-life exponent is p = 4, in agreement with the 1947 Lundberg-Palmgren value but crowning reduces the value of the exponent, p. The lives of modern roller bearings made from vacuum-processed steels significantly exceed those predicted by the Lundberg-Palmgren theory. The Zaretsky rolling-element bearing life model of 1996 produces a load-life exponent of p = 5 for flat rollers, which is more consistent with test data. For the Zaretsky model with fully crowned rollers p = 4.3. For an aerospace profile and chamfered rollers, p = 4.6. Using the 1952 Lundberg-Palmgren value p = 10/3, the value incorporated in ANSI/ABMA and ISO bearing standards, can create significant life calculation errors for roller bearings.

  16. 8. DETAIL VIEW OF HEADHOUSE/PIER, SHOWING ROLLER GATE, ROLLER TRACK, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    8. DETAIL VIEW OF HEADHOUSE/PIER, SHOWING ROLLER GATE, ROLLER TRACK, CHAIN, GATE HEATER AND DAM BRIDGE, LOOKING WEST - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 4, Alma, Buffalo County, WI

  17. Tapered capillary optics

    DOEpatents

    Hirsch, Gregory

    1998-01-01

    A metal or glass wire is etched with great precision into a very narrowly tapering cone which has the shape of the desired final capillary-optics bore. By controlling the rate of removal of the wire from an etchant bath, a carefully controlled taper is produced. A sensor measures the diameter of the wire as it leaves the surface of the etchant. This signal is used for feedback control of the withdrawal speed. The etched wire undergoes a treatment to produce an extremely low surface-roughness. The etched and smoothed wire is coated with the material of choice for optimizing the reflectivity of the radiation being focused. This could be a vacuum evaporation, sputtering, CVD or aqueous chemical process. The coated wire is either electroplated, built up with electroless plating, or encapsulated in a polymer cylinder such as epoxy to increase the diameter of the wire for easier handling and greater robustness. During this process, the wire is vertically oriented and tensioned to assure that the wire is absolutely straight. The coated and electroformed wire is bonded to a flat, rigid substrate and is then periodically segmented by cutting or etching a series of narrow slits or grooves into the wire. The wire is vertically oriented and tensioned during the bonding process to assure that it is straight. The original wire material is then chemically etched away through the slits or otherwise withdrawn to leave the hollow internal bore of the final tapered-capillary optical element.

  18. Influence of Roller Burnishing Parameters on Depletion of Plasticity Reserve

    NASA Astrophysics Data System (ADS)

    Blumenstein, V. Yu; Petrenko, K. P.

    2016-04-01

    Roller burnishing process considerably increases surface quality and service life of machine parts. Efficiency of roller burnishing rises greatly when technological inheritance (TI) is taken into account. Research results of degree of plasticity reserve depletion (DPRD) while roller burnishing are presented. Results obtained made it possible to establish mechanisms of strain accumulation and plasticity reserve depletion according to roller burnishing parameters.

  19. 36 CFR 13.916 - Use of roller skates, skateboards, roller skis, in-line skates, and similar devices.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 36 Parks, Forests, and Public Property 1 2011-07-01 2011-07-01 false Use of roller skates, skateboards, roller skis, in-line skates, and similar devices. 13.916 Section 13.916 Parks, Forests, and..., skateboards, roller skis, in-line skates, and similar devices. The use of roller skates, skateboards,...

  20. 36 CFR 13.916 - Use of roller skates, skateboards, roller skis, in-line skates, and similar devices.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 36 Parks, Forests, and Public Property 1 2012-07-01 2012-07-01 false Use of roller skates, skateboards, roller skis, in-line skates, and similar devices. 13.916 Section 13.916 Parks, Forests, and..., skateboards, roller skis, in-line skates, and similar devices. The use of roller skates, skateboards,...

  1. 36 CFR 13.916 - Use of roller skates, skateboards, roller skis, in-line skates, and similar devices.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 36 Parks, Forests, and Public Property 1 2013-07-01 2013-07-01 false Use of roller skates, skateboards, roller skis, in-line skates, and similar devices. 13.916 Section 13.916 Parks, Forests, and..., skateboards, roller skis, in-line skates, and similar devices. The use of roller skates, skateboards,...

  2. 36 CFR 13.916 - Use of roller skates, skateboards, roller skis, in-line skates, and similar devices.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 36 Parks, Forests, and Public Property 1 2014-07-01 2014-07-01 false Use of roller skates, skateboards, roller skis, in-line skates, and similar devices. 13.916 Section 13.916 Parks, Forests, and..., skateboards, roller skis, in-line skates, and similar devices. The use of roller skates, skateboards,...

  3. TAPERED DEFINING SLOT

    DOEpatents

    Pressey, F.W.

    1959-09-01

    An improvement is reported in the shape and formation of the slot or opening in the collimating slot member which forms part of an ion source of the type wherein a vapor of the material to be ionized is bombarded by electrons in a magnetic field to strike an arc-producing ionization. The defining slot is formed so as to have a substantial taper away from the cathode, causing the electron bombardment from the cathode to be dispersed over a greater area reducing its temperature and at the same time bringing the principal concentration of heat from the electron bombardment nearer the anode side of the slot, thus reducing deterioration and prolonging the life of the slot member during operation.

  4. Tapered undulator for SASE FELs

    SciTech Connect

    Fawley, William M.; Huang, Zhirong; Kim, Kwang-Je; Vinokurov, Nikolai A.

    2001-09-14

    We discuss the use of tapered undulators to enhance the performance of free-electron lasers (FELs) based upon self-amplified spontaneous emission (SASE), where the radiation tends to have a relatively broad bandwidth, limited temporal phase coherence, and large amplitude fluctuations. Using the polychromatic FEL simulation code GINGER, we numerically demonstrate the effectiveness of a tapered undulator for parameters corresponding to the existing Argonne low-energy undulator test line (LEUTL) FEL. We also study possible tapering options for proposed x-ray FELs such as the Linac Coherent Light Source (LCLS).

  5. Screw-released roller brake

    NASA Technical Reports Server (NTRS)

    Vranish, John M. (Inventor)

    1999-01-01

    A screw-released roller brake including an input drive assembly, an output drive assembly, a plurality of locking sprags, a mechanical tripper nut for unlocking the sprags, and a casing therefor. The sprags consist of three dimensional (3-D) sprag members having pairs of contact surface regions which engage respective pairs of contact surface regions included in angular grooves or slots formed in the casing and the output drive assembly. The sprags operate to lock the output drive assembly to the casing to prevent rotation thereof in an idle mode of operation. In a drive mode of operation, the tripper is either self actuated or motor driven and is translated linearly up and down against a spline and at the limit of its travel rotates the sprags which unlock while coupling the input drive assembly to the output drive assembly so as to impart a turning motion thereto in either a clockwise or counterclockwise direction.

  6. Unique slider bed eliminates problematic idler rollers

    SciTech Connect

    Not Available

    1988-01-01

    Solidur Plastic's impact slide bed is an innovative solution to problems with idler rollers. The unit provides increased conveyor efficiency and prolonged belt life. It also reduces costly downtime and maintenance needs by eliminating typical idler and conveyor belting problems.

  7. Kidney Stone? Try a Roller Coaster Ride

    MedlinePlus

    ... Space Mountain roller coasters at Orlando's Walt Disney World -- seems to support that view. In the study, Wartinger's group used 3D printing to create a clear silicone model of a kidney that contained urine, plus three ...

  8. Tapered undulators for SASE FELs

    NASA Astrophysics Data System (ADS)

    Fawley, William M.; Huang, Zhirong; Kim, Kwang-Je; Vinokurov, Nikolai A.

    2002-05-01

    We discuss the use of tapered undulators to enhance the performance of free-electron lasers (FELs) based upon self-amplified spontaneous emission, where the radiation tends to have a relatively broad bandwidth and limited temporal coherence. Using the polychromatic FEL simulation code GINGER, we numerically demonstrate the effectiveness of tapered undulators for parameters corresponding to the Argonne low-energy undulator test line FEL and the proposed linac coherent light source.

  9. Pulmonary hemorrhage resulting from roller coaster.

    PubMed

    Yin, Ming; Tian, Qing; Shen, Hong

    2011-03-01

    Roller coasters are probably one of the more popular rides at amusement parks around the world, and there are few reported injuries. We report a case of symmetric diffuse upper lobe hemorrhage resulting from roller coaster in a previously healthy woman. The clinical course, management, and etiology of her case are discussed; and the literature is reviewed. To our knowledge, pulmonary hemorrhage in this setting has not yet been described. PMID:20825914

  10. Environmental impact studies of Chrome rollers used by cotton roller ginning industries and design and development of pollution free chromeless RCF rollers.

    PubMed

    Singh, Gurdeep; Iyer, G Vijayan

    2004-01-01

    This study focuses on environmental chromium contamination and pollution caused by the use of Chrome Composite Leather-Clad (CCLC) rollers commonly used in cotton roller ginning industries and attempts to eliminate this problem by providing eco-friendly chrome-less rollers.

  11. Adhesive Wear of Rollers in Vacuum

    NASA Technical Reports Server (NTRS)

    Shaeef, Iqbal; Krantz, Timothy L.

    2012-01-01

    This work was done to support NASA's James Webb Space Telescope that is equipped with a Near Infrared Camera and Spectrograph and Micro Shutter Assembly (MSA). A MSA mechanism's qualification test in cryogenic vacuum at 30deg K for 96K cycles resulted in roller wear and formation of some debris. Lab tests in vacuum were conducted at NASA Glenn Research Center (GRC) to understand the wear of Ti6Al4V mated with 440F steel rollers. Misalignment angle was found to have the most significant effect on debris formation. At misalignment angle of 1.4deg, significant amount of wear debris were formed within 50,000 cycles. Very few wear particles were found for a zero misalignment angle, and the total wear was small even after 367,000 cycles. The mode of wear in all the tests was attributed to adhesion, which was clearly evident from video records as well as the plate-like amalgamated debris material from both rollers. The adhesive wear rate was found to be approximately proportional to the misalignment angle. The wear is a two-way phenomenon, and the mixing of both roller materials in wear debris was confirmed by x-ray fluorescence (XRF) and EDX spectra. While there was a net loss of mass from the steel rollers, XRF and energy dispersive x-ray (EDX) spectra showed peaks of Ti on steel rollers, and peaks of Fe on Ti rollers. These results are useful for designers in terms of maintaining appropriate tolerances to avoid misalignment of rolling elements and the resulting severe wear

  12. 12. DETAIL VIEW OF CIRCULAR BRONZE ROLLER GATE POSITION GAUGE, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    12. DETAIL VIEW OF CIRCULAR BRONZE ROLLER GATE POSITION GAUGE, ROLLER GATE PIER HOUSE, TYPE 2A, DAM - Mississippi River 9-Foot Channel Project, Lock & Dam No. 11, Upper Mississippi River, Dubuque, Dubuque County, IA

  13. 49 CFR 215.115 - Defective roller bearing.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Defective roller bearing. 215.115 Section 215.115... § 215.115 Defective roller bearing. (a) A railroad may not place or continue in service a car, if the car has— (1) A roller bearing that shows signs of having been overheated as evidenced by—...

  14. 49 CFR 215.115 - Defective roller bearing.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Defective roller bearing. 215.115 Section 215.115... § 215.115 Defective roller bearing. (a) A railroad may not place or continue in service a car, if the car has— (1) A roller bearing that shows signs of having been overheated as evidenced by—...

  15. 49 CFR 215.117 - Defective roller bearing adapter.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Defective roller bearing adapter. 215.117 Section... Suspension System § 215.117 Defective roller bearing adapter. A railroad may not place or continue in service a car, if the car has a roller bearing adapter that is— (a) Cracked or broken; (b) Not in its...

  16. 49 CFR 215.117 - Defective roller bearing adapter.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Defective roller bearing adapter. 215.117 Section... Suspension System § 215.117 Defective roller bearing adapter. A railroad may not place or continue in service a car, if the car has a roller bearing adapter that is— (a) Cracked or broken; (b) Not in its...

  17. 49 CFR 230.103 - Tender roller bearing journal boxes.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Tender roller bearing journal boxes. 230.103 Section 230.103 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD... Locomotives and Tenders Running Gear § 230.103 Tender roller bearing journal boxes. Tender roller...

  18. 49 CFR 230.103 - Tender roller bearing journal boxes.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Tender roller bearing journal boxes. 230.103 Section 230.103 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD... Locomotives and Tenders Running Gear § 230.103 Tender roller bearing journal boxes. Tender roller...

  19. 49 CFR 230.103 - Tender roller bearing journal boxes.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Tender roller bearing journal boxes. 230.103 Section 230.103 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD... Locomotives and Tenders Running Gear § 230.103 Tender roller bearing journal boxes. Tender roller...

  20. 49 CFR 230.103 - Tender roller bearing journal boxes.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Tender roller bearing journal boxes. 230.103 Section 230.103 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD... Locomotives and Tenders Running Gear § 230.103 Tender roller bearing journal boxes. Tender roller...

  1. 49 CFR 215.117 - Defective roller bearing adapter.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Defective roller bearing adapter. 215.117 Section... Suspension System § 215.117 Defective roller bearing adapter. A railroad may not place or continue in service a car, if the car has a roller bearing adapter that is— (a) Cracked or broken; (b) Not in its...

  2. 49 CFR 215.115 - Defective roller bearing.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Defective roller bearing. 215.115 Section 215.115... § 215.115 Defective roller bearing. (a) A railroad may not place or continue in service a car, if the car has— (1) A roller bearing that shows signs of having been overheated as evidenced by—...

  3. 49 CFR 215.115 - Defective roller bearing.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Defective roller bearing. 215.115 Section 215.115... § 215.115 Defective roller bearing. (a) A railroad may not place or continue in service a car, if the car has— (1) A roller bearing that shows signs of having been overheated as evidenced by—...

  4. 49 CFR 215.115 - Defective roller bearing.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Defective roller bearing. 215.115 Section 215.115... § 215.115 Defective roller bearing. (a) A railroad may not place or continue in service a car, if the car has— (1) A roller bearing that shows signs of having been overheated as evidenced by—...

  5. 49 CFR 215.117 - Defective roller bearing adapter.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Defective roller bearing adapter. 215.117 Section... Suspension System § 215.117 Defective roller bearing adapter. A railroad may not place or continue in service a car, if the car has a roller bearing adapter that is— (a) Cracked or broken; (b) Not in its...

  6. 49 CFR 215.117 - Defective roller bearing adapter.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Defective roller bearing adapter. 215.117 Section... Suspension System § 215.117 Defective roller bearing adapter. A railroad may not place or continue in service a car, if the car has a roller bearing adapter that is— (a) Cracked or broken; (b) Not in its...

  7. 49 CFR 230.103 - Tender roller bearing journal boxes.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Tender roller bearing journal boxes. 230.103... Locomotives and Tenders Running Gear § 230.103 Tender roller bearing journal boxes. Tender roller bearing journal boxes shall be maintained in a safe and suitable condition....

  8. 29 CFR 1918.63 - Chutes, gravity conveyors and rollers.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 7 2011-07-01 2011-07-01 false Chutes, gravity conveyors and rollers. 1918.63 Section 1918... Equipment Other Than Ship's Gear § 1918.63 Chutes, gravity conveyors and rollers. (a) Chutes shall be of... and gravity conveyor roller sections shall be firmly placed and secured to prevent...

  9. 29 CFR 1918.63 - Chutes, gravity conveyors and rollers.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 7 2014-07-01 2014-07-01 false Chutes, gravity conveyors and rollers. 1918.63 Section 1918... Equipment Other Than Ship's Gear § 1918.63 Chutes, gravity conveyors and rollers. (a) Chutes shall be of... and gravity conveyor roller sections shall be firmly placed and secured to prevent...

  10. 29 CFR 1918.63 - Chutes, gravity conveyors and rollers.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Chutes, gravity conveyors and rollers. 1918.63 Section 1918... Equipment Other Than Ship's Gear § 1918.63 Chutes, gravity conveyors and rollers. (a) Chutes shall be of... and gravity conveyor roller sections shall be firmly placed and secured to prevent...

  11. 29 CFR 1918.63 - Chutes, gravity conveyors and rollers.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 7 2012-07-01 2012-07-01 false Chutes, gravity conveyors and rollers. 1918.63 Section 1918... Equipment Other Than Ship's Gear § 1918.63 Chutes, gravity conveyors and rollers. (a) Chutes shall be of... and gravity conveyor roller sections shall be firmly placed and secured to prevent...

  12. 28. Photocopy of Crown Roller Mill illustration; originally published in ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    28. Photocopy of Crown Roller Mill illustration; originally published in The Crown Roller Mill, Northwestern Miller 9 (May 21, 1880): 321; SHOWING WEST SIDE, LOOKING EAST - Crown Roller Mill, 105 Fifth Avenue, South, West Side Milling District, Minneapolis, Hennepin County, MN

  13. Magnetostrictive Roller-Drive Stepping Motor

    NASA Technical Reports Server (NTRS)

    Vranish, John M.

    1993-01-01

    Proposed motor based on magnetostrictive effect provides stepped angular motion with angular increments of order of 100 microradians. Driven to repeat stepping cycle rapidly enough to achieve maximum speed of about 20 rpm, provides torque an order of magnitude greater than electric motors, and brakes itself when power turned off. Magnetostrictive rods in electromagnet coils push against drive plate, causing it to rotate slightly. This slight rotation jams conical rollers between cam surfaces on outer drive ring and split drum, so rollers transmit rotation to drum. Suitable for precise, high-torque, fail-safe-braking, direct drive of robot joint, without bulk and weight of additional brake mechanism and gear train.

  14. Remote Sensing Characteristics of Wave Breaking Rollers

    NASA Astrophysics Data System (ADS)

    Haller, M. C.; Catalan, P.

    2006-12-01

    The wave roller has a primary influence on the balances of mass and momentum in the surf zone (e.g. Svendsen, 1984; Dally and Brown, 1995; Ruessink et al., 2001). In addition, the roller area and its angle of inclination on the wave front are important quantities governing the dissipation rates in breaking waves (e.g Madsen et al., 1997). Yet, there have been very few measurements published of individual breaking wave roller geometries in shallow water. A number of investigators have focused on observations of the initial jet-like motion at the onset of breaking before the establishment of the wave roller (e.g. Basco, 1985; Jansen, 1986), while Govender et al. (2002) provide observations of wave roller vertical cross-sections and angles of inclination for a pair of laboratory wave conditions. Nonetheless, presently very little is known about the growth, evolution, and decay of this aerated region of white water as it propagates through the surf zone; mostly due to the inherent difficulties in making the relevant observations. The present work is focused on analyzing observations of the time and space scales of individual shallow water breaking wave rollers as derived from remote sensing systems. Using a high-resolution video system in a large-scale laboratory facility, we have obtained detailed measurements of the growth and evolution of the wave breaking roller. In addition, by synchronizing the remote video with in-situ wave gages, we are able to directly relate the video intensity signal to the underlying wave shape. Results indicate that the horizontal length scale of breaking wave rollers differs significantly from the previous observations of Duncan (1981), which has been a traditional basis for roller model parameterizations. The overall approach to the video analysis is new in the sense that we concentrate on individual breaking waves, as opposed to the more commonly used time-exposure technique. In addition, a new parameter of interest, denoted Imax, is

  15. Roller compaction of moist pharmaceutical powders.

    PubMed

    Wu, C-Y; Hung, W-L; Miguélez-Morán, A M; Gururajan, B; Seville, J P K

    2010-05-31

    The compression behaviour of powders during roller compaction is dominated by a number of factors, such as process conditions (roll speed, roll gap, feeding mechanisms and feeding speed) and powder properties (particle size, shape, moisture content). The moisture content affects the powder properties, such as the flowability and cohesion, but it is not clear how the moisture content will influence the powder compression behaviour during roller compaction. In this study, the effect of moisture contents on roller compaction behaviour of microcrystalline cellulose (MCC, Avicel PH102) was investigated experimentally. MCC samples of different moisture contents were prepared by mixing as-received MCC powder with different amount of water that was sprayed onto the powder bed being agitated in a rotary mixer. The flowability of these samples were evaluated in terms of the poured angle of repose and flow functions. The moist powders were then compacted using the instrumented roller compactor developed at the University of Birmingham. The flow and compression behaviour during roller compaction and the properties of produced ribbons were examined. It has been found that, as the moisture content increases, the flowability of moist MCC powders decreases and the powder becomes more cohesive. As a consequence of non-uniform flow of powder into the compaction zone induced by the friction between powder and side cheek plates, all produced ribbons have a higher density in the middle and lower densities at the edges. For the ribbons made of powders with high moisture contents, different hydration states across the ribbon width were also identified from SEM images. Moreover, it was interesting to find that these ribbons were split into two halves. This is attributed to the reduction in the mechanical strength of moist powder compacts with high moisture contents produced at high compression pressures.

  16. Roller compaction of moist pharmaceutical powders.

    PubMed

    Wu, C-Y; Hung, W-L; Miguélez-Morán, A M; Gururajan, B; Seville, J P K

    2010-05-31

    The compression behaviour of powders during roller compaction is dominated by a number of factors, such as process conditions (roll speed, roll gap, feeding mechanisms and feeding speed) and powder properties (particle size, shape, moisture content). The moisture content affects the powder properties, such as the flowability and cohesion, but it is not clear how the moisture content will influence the powder compression behaviour during roller compaction. In this study, the effect of moisture contents on roller compaction behaviour of microcrystalline cellulose (MCC, Avicel PH102) was investigated experimentally. MCC samples of different moisture contents were prepared by mixing as-received MCC powder with different amount of water that was sprayed onto the powder bed being agitated in a rotary mixer. The flowability of these samples were evaluated in terms of the poured angle of repose and flow functions. The moist powders were then compacted using the instrumented roller compactor developed at the University of Birmingham. The flow and compression behaviour during roller compaction and the properties of produced ribbons were examined. It has been found that, as the moisture content increases, the flowability of moist MCC powders decreases and the powder becomes more cohesive. As a consequence of non-uniform flow of powder into the compaction zone induced by the friction between powder and side cheek plates, all produced ribbons have a higher density in the middle and lower densities at the edges. For the ribbons made of powders with high moisture contents, different hydration states across the ribbon width were also identified from SEM images. Moreover, it was interesting to find that these ribbons were split into two halves. This is attributed to the reduction in the mechanical strength of moist powder compacts with high moisture contents produced at high compression pressures. PMID:20176096

  17. Thread gauge for tapered threads

    DOEpatents

    Brewster, Albert L.

    1994-01-11

    The thread gauge permits the user to determine the pitch diameter of tapered threads at the intersection of the pitch cone and the end face of the object being measured. A pair of opposed anvils having lines of threads which match the configuration and taper of the threads on the part being measured are brought into meshing engagement with the threads on opposite sides of the part. The anvils are located linearly into their proper positions by stop fingers on the anvils that are brought into abutting engagement with the end face of the part. This places predetermined reference points of the pitch cone of the thread anvils in registration with corresponding points on the end face of the part being measured, resulting in an accurate determination of the pitch diameter at that location. The thread anvils can be arranged for measuring either internal or external threads.

  18. Thread gauge for tapered threads

    DOEpatents

    Brewster, A.L.

    1994-01-11

    The thread gauge permits the user to determine the pitch diameter of tapered threads at the intersection of the pitch cone and the end face of the object being measured. A pair of opposed anvils having lines of threads which match the configuration and taper of the threads on the part being measured are brought into meshing engagement with the threads on opposite sides of the part. The anvils are located linearly into their proper positions by stop fingers on the anvils that are brought into abutting engagement with the end face of the part. This places predetermined reference points of the pitch cone of the thread anvils in registration with corresponding points on the end face of the part being measured, resulting in an accurate determination of the pitch diameter at that location. The thread anvils can be arranged for measuring either internal or external threads. 13 figures.

  19. Cyclic fatigue resistance of two variable-taper rotary file systems: ProTaper universal and V-Taper.

    PubMed

    Whipple, Sterling J; Kirkpatrick, Timothy C; Rutledge, Richard E

    2009-04-01

    The cyclic fatigue resistance of ProTaper Universal (Dentsply Tulsa Dental Specialties, Tulsa, OK) and V-Taper (Guidance Endo, Albuquerque, NM) files was measured while rotating files around a 5-mm radius curve with 90 degrees of maximum flexure. The files were rotated at 250 rpm with a continuous axial oscillation of 4 mm at 1 Hz. The number of cycles to failure was calculated and analyzed by using univariate analysis of variance and the Tukey HSD posthoc test with results confirmed by nonparametric Kruskal-Wallis and Mann-Whitney U tests with a Bonferroni correction. The fracture faces of representative files were imaged with a scanning electron microscope to confirm cyclic fatigue as the mode of fracture. For the instruments tested, the ProTaper files appeared to resist fracture better than the V-Taper files. At each tip size tested, the ProTaper files either outperformed or were not statistically different than V-Taper files.

  20. Experimental Investigation of Forces Produced by Misaligned Steel Rollers

    NASA Technical Reports Server (NTRS)

    Krantz, Timothy; DellaCorte, Christopher; Dube, Michael

    2010-01-01

    The International Space Station Solar Alpha Rotary Joint (SARJ) uses a roller-based mechanism for positioning of the solar arrays. The forces and moments that develop at the roller interfaces are influenced by the design including the kinematic constraints and the lubrication condition. To help understand the SARJ operation, a set of dedicated experiments were completed using roller pairs. Of primary interest was to measure the axial force directed along the axis of rotation of the roller as a function of shaft misalignment. The conditions studied included dry and clean surfaces; one surface plated by a gold film, and greased surfaces. For the case of a bare 440C roller against a nitrided 15-5 roller without lubrication, the axial force can be as great as 0.4 times the normal load for a shaft angle of 0.5 degree. Such a magnitude of force on a roller in the SARJ mechanism would cause roller tipping and contact pressures much greater than anticipated by the designers. For the case of a bare 440C roller against a nitrided 15-5 roller with grease lubrication, the axial force does not exceed about 0.15 times the normal load even for the largest misalignment angles tested. Gold films provided good lubrication for the short duration testing reported herein. Grease lubrication limited the magnitude of the axial force to even smaller magnitudes than was achieved with the gold films. The experiments demonstrate the critical role of good lubrication for the SARJ mechanism.

  1. Experimental Investigation of Forces Produced by Misaligned Steel Rollers

    NASA Technical Reports Server (NTRS)

    Krantz, Timothy; DellaCorte, Christopher; Dube, Michael

    2010-01-01

    The International Space Station (ISS) Solar Alpha Rotary Joint (SARJ) uses a roller-based mechanism for positioning of the solar arrays. The forces and moments that develop at the roller interfaces are influenced by the design including the kinematic constraints and the lubrication condition. To help understand the SARJ operation, a set of dedicated experiments were completed using roller pairs. Of primary interest was to measure the axial force directed along the axis of rotation of the roller as a function of shaft misalignment. The conditions studied included dry and clean surfaces; one surface plated by a gold film, and greased surfaces. For the case of a bare 440C roller against a nitrided 15-5 roller without lubrication, the axial force can be as great as 0.4 times the normal load for a shaft angle of 0.5 deg. Such a magnitude of force on a roller in the SARJ mechanism would cause roller tipping and contact pressures much greater than anticipated by the designers. For the case of a bare 440C roller against a nitrided 15-5 roller with grease lubrication, the axial force does not exceed about 0.15 times the normal load even for the largest misalignment angles tested. Gold films provided good lubrication for the short duration testing reported herein. Grease lubrication limited the magnitude of the axial force to even smaller magnitudes than was achieved with the gold films. The experiments demonstrate the critical role of good lubrication for the SARJ mechanism.

  2. Mechanically assisted taper corrosion in modular TKA.

    PubMed

    Arnholt, Christina M; MacDonald, Daniel W; Tohfafarosh, Mariya; Gilbert, Jeremy L; Rimnac, Clare M; Kurtz, Steven M; Klein, Gregg; Mont, Michael A; Parvizi, Javad; Cates, Harold E; Lee, Gwo-Chin; Malkani, Arthur; Kraay, Mattheuw

    2014-09-01

    The purpose of this study was to characterize the prevalence of taper damage in modular TKA components. One hundred ninety-eight modular components were revised after 3.9±4.2 years of implantation. Modular components were evaluated for fretting corrosion using a semi-quantitative 4-point scoring system. Design features and patient information were assessed as predictors of fretting corrosion damage. Mild-to-severe fretting corrosion (score ≥2) was observed in 94/101 tapers on the modular femoral components and 90/97 tapers on the modular tibial components. Mixed alloy pairs (p=0.03), taper design (p<0.001), and component type (p=0.02) were associated with taper corrosion. The results from this study supported the hypothesis that there is taper corrosion in TKA. However the clinical implications remain unclear.

  3. Rollers smell the fear of nestlings.

    PubMed

    Parejo, D; Amo, L; Rodríguez, J; Avilés, J M

    2012-08-23

    Many animals react to danger by producing chemical cues that can be smelled by others, which is called the smell of fear. Some bird species produce chemical compounds when threatened, such as nestlings of the Eurasian roller Coracias garrulus that vomit an odorous orange liquid when scared in their nests. Here, we experimentally explore the possibility that parents were informed about recent predation attempts at their nests through the olfaction of this vomit. Parents of nests treated with nestling vomit delayed their entrance to nests and decreased their provisioning rate in comparison with parents of nests treated with an odorous control. These results demonstrate that adult rollers are able to smell the fear of offspring and show for the first time in birds that a scent produced during an interspecific challenge has a role in an intraspecific communication scenario.

  4. Elastic buckling of tapered circular plates

    NASA Astrophysics Data System (ADS)

    Wang, C. M.; Hong, G. M.; Tan, T. J.

    1995-06-01

    This paper is concerned with the elastic buckling of tapered circular plates. The study is prompted by the fact that results hitherto available are restricted to a narrow range of taper parameters and are somewhat different from each other. For the buckling analysis, a simple and yet accurate numerical method is presented. It is based on the shooting method and the Rayleigh-Ritz approach. Comprehensive generic buckling results of circular plates with linearly and parabolically varying thicknesses are generated. Comparison studies of the buckling results showed that some of the existing results were erroneous. Optimal values of taper parameters for such tapered plates are also given.

  5. Theory and Simulations of Tapered Diblock Polymers

    NASA Astrophysics Data System (ADS)

    Hall, Lisa M.; Seo, Youngmi; Brown, Jonathan R.

    We study tapered block polymers, AB diblock polymers with a gradient region inserted between the pure A and B blocks such that composition smoothly transitions from A to B (or B to A in the case of inverse tapers). Phase diagrams were created using self consistent field theory (SCFT), and coarse-grained molecular dynamics (MD) simulations were used to study polymer conformations and diffusion, including diffusion of monomer-sized penetrants preferentially dissolved in one of the phases. As has been observed experimentally, we find that tapering makes the A and B blocks more miscible, decreasing domain spacing and shifting the order to disorder transition to lower temperatures. We predict a widening of the bicontinuous double gyroid region of the phase diagram for moderate length normal tapers versus diblocks, suggesting taper length can be used as a control parameter to obtain network phases even at high molecular weight, as may be desirable in transport applications. Additionally, in some inverse tapered systems, SCFT predicts phases not present in the standard AB diblock phase diagram, and MD simulations show how the chains fold back and forth across the interface. In these inverse tapered polymers, as segregation strength is increased, the competing effects of folding and stretching produces lamellae that have domain spacing nearly independent of temperature. We also find that diffusion of penetrants in normal tapers is significantly faster than that in inverse tapers, which is likely related to their unusual conformations. This material is based upon work supported by DOE Grant SC0014209.

  6. Interference Fit Life Factors for Roller Bearings

    NASA Technical Reports Server (NTRS)

    Oswald, Fred B.; Zaretsky, Erwin V.; Poplawski, Joseph V.

    2008-01-01

    The effect of hoop stresses in reducing cylindrical roller bearing fatigue life was determined for various classes of inner ring interference fit. Calculations were performed for up to seven interference fit classes for each of ten bearing sizes. Each fit was taken at tightest, average and loosest values within the fit class for RBEC-5 tolerance, thus requiring 486 separate analyses. The hoop stresses were superimposed on the Hertzian principal stresses created by the applied radial load to calculate roller bearing fatigue life. The method was developed through a series of equations to calculate the life reduction for cylindrical roller bearings based on interference fit. All calculated lives are for zero initial bearing internal clearance. Any reduction in bearing clearance due to interference fit was compensated by increasing the initial (unmounted) clearance. Results are presented as tables and charts of life factors for bearings with light, moderate and heavy loads and interference fits ranging from extremely light to extremely heavy and for bearing accuracy class RBEC 5 (ISO class 5). Interference fits on the inner bearing ring of a cylindrical roller bearing can significantly reduce bearing fatigue life. In general, life factors are smaller (lower life) for bearings running under light load where the unfactored life is highest. The various bearing series within a particular bore size had almost identical interference fit life factors for a particular fit. The tightest fit at the high end of the RBEC-5 tolerance band defined in ANSI/ABMA shaft fit tables produces a life factor of approximately 0.40 for an inner-race maximum Hertz stress of 1200 MPa (175 ksi) and a life factor of 0.60 for an inner-race maximum Hertz stress of 2200 MPa (320 ksi). Interference fits also impact the maximum Hertz stress-life relation.

  7. Kinematic stability of roller pairs in free rolling contact

    NASA Technical Reports Server (NTRS)

    Savage, M.; Loewenthal, S. H.

    1976-01-01

    A set of generalized stability equations was developed for roller pairs in free rolling contact. A symmetric, dual contact model was used. Four possible external contact profiles that possess continuous contacting surfaces were studied. It was found that kinematic stability would be insured if the larger radius of transverse curvature, in absolute value, and the smaller rolling radius both exist on the roller that has the apex of its conical surface outboard of its main body. The stability criteria developed are considered to be useful for assessing axial restraint requirements for a variety of roller mechanisms and in the selection of roller contact geometry for traction drive devices.

  8. Calculation of tapered monoplane wings

    NASA Technical Reports Server (NTRS)

    Amstutz, E

    1930-01-01

    The tapered wing shape increases the lift in the middle of the wing and thus reduces the bending moment of the lifting forces in the plane of symmetry. Since this portion of the wing is the thickest, the stresses of the wing material are reduced and desirable space is provided for stowing the loads in the wing. This statically excellent form of construction, however, has aerodynamic disadvantages which must be carefully weighed, if failures are to be avoided. This treatise is devoted to the consideration of these problems.

  9. Simulations of the TJNAF FEL with tapered and inversely tapered undulators

    SciTech Connect

    A. Christodoulou; D. Lampiris; W.B. Colson; P.P. Crooker; J. Blau; R.D. McGinnis; Steve Benson; Joseph Gubeli; George Neil

    2001-12-01

    Experiments using the TJNAF FEL have explored the operation with both tapered and inversely tapered undulators. We present here numerical simulations using the TJNAF experimental parameters, including the effects of taper. Single-mode simulations show the effect of taper on gain. Multimode simulations describe the evolution of short optical pulses in the far infrared, and show how taper affects single-pass gain and steady-state power as a function of desynchronism. A short optical pulse presents an ever-changing field strength to each section of the electron pulse so that idealized operation is not possible. Yet, advantages for the recirculation of the electron beam can be explored.

  10. Eco-friendly rubberized cotton fabric roller for ginning machines.

    PubMed

    Iyer, G V

    2007-01-01

    This article discusses the pollution caused by chrome composite leather-clad (CCLC) rollers commonly used in cotton roller ginning mills and suggests an alternative roller material. CCLC rollers contain about 18,000 to 36,000 mg/kg (ppm) total chromium in trivalent and hexavalent forms, which are toxic to human health and carcinogenic. When seed-cotton is processed in double roller (DR) ginning machines, the lint is contaminated with chromium, and chromium particles are carried into the spun yarns and cotton by-products. Specifically, due to persistent rubbing of the leather-clad roller over the stationary knife during the ginning process, the lint is contaminated with about 140 to 1990 ppm of chromium, and the spun yarns and cotton by-products contain about 100 to 200 ppm, far in excess of the standard limit of 0.1 ppm. Gin and mill workers are directly exposed to this carcinogenic substance. To offset this problem, pollution-free rubberized cotton fabric (RCF) rollers have been fabricated and tested in roller gins. The RCF roller covering is made of multiple layers of fabric bonded together using a white rubber compound, which has a surface finish conducive to high ginning efficiency. This eliminates chromium contamination and pollution during the ginning process. On the basis of the design and development of various test rollers and subsequent evaluation studies, the performance of pollution-free RCF rollers has been demonstrated with reference to their commercial benefit and eco-friendliness in cotton ginning mills.

  11. Mechanically Assisted Taper Corrosion in Modular TKA

    PubMed Central

    Arnholt, Christina; MacDonald, Daniel W.; Tohfafarosh, Mariya; Gilbert, Jeremy L.; Rimnac, Clare M.; Kurtz, Steven M.; Klein, Gregg; Mont, Michael A.; Parvizi, Javad; Cates, Harold E.; Lee, Gwo-Chin; Malkani, Arthur; Kraay, Matthew

    2014-01-01

    The purpose of this study was to characterize the prevalence of taper damage in modular TKA components. 198 modular components were revised after 3.9±4.2y (range: 0.0–17.5y). Modular components were evaluated for fretting corrosion using a semi-quantitative 4-point scoring system. Flexural rigidity, stem diameter, alloy coupling, patient weight, age and implantation time were assessed as predictors of fretting corrosion damage. Mild-to-severe fretting corrosion (score≥2) was observed in 94/101 of the tapers on the modular femoral components and 90/97 of the modular tibial components. Mixed alloy pairs (p=0.03), taper design (p<0.001), and component type (p=0.02) were associated with taper corrosion. The results from this study supported the hypothesis that there is taper corrosion in TKA. However the clinical implications of fretting and corrosion in TKA remain unclear. PMID:24996586

  12. Radiation characteristics of tapered slab waveguides

    NASA Astrophysics Data System (ADS)

    Scheggi, A. M.; Falciai, R.; Brenci, M.

    1983-01-01

    The application of ray optics to the evaluation of near- and far-field radiation patterns of a slab waveguide taper is discussed, noting the importance of calculating the power that can be extracted from the core at the end of the waveguide related to the near-field configurations. A multimode, tapered slab waveguide with a homogeneous core and unlimited cladding is considered. It is pointed out that as the ray proceeds on its zigzag path down the taper, its propagation angle increases from reflection to reflection and eventually surpasses the limit angle of total reflection. To obtain an overall idea of the range of ray angles accepted at the smaller end of the taper, the Williamson (1952) method is used; this makes it possible, through a simple geometrical construction, to trace the ray in a linear cone. It is found that the ray-tracing technique can constitute an adequate tool in the analysis and design of tapered multimode waveguides.

  13. Sensing roller for in-process thickness measurement

    DOEpatents

    Novak, J.L.

    1996-07-16

    An apparatus and method are disclosed for processing materials by sensing roller, in which the sensing roller has a plurality of conductive rings (electrodes) separated by rings of dielectric material. Sensing capacitances or impedances between the electrodes provides information on thicknesses of the materials being processed, location of wires therein, and other like characteristics of the materials. 6 figs.

  14. Sensing roller for in-process thickness measurement

    DOEpatents

    Novak, James L.

    1996-01-01

    An apparatus and method for processing materials by sensing roller, in which the sensing roller has a plurality of conductive rings (electrodes) separated by rings of dielectric material. Sensing capacitances or impedances between the electrodes provides information on thicknesses of the materials being processed, location of wires therein, and other like characteristics of the materials.

  15. Head motions while riding roller coasters: implications for brain injury.

    PubMed

    Pfister, Bryan J; Chickola, Larry; Smith, Douglas H

    2009-12-01

    The risk of traumatic brain injury (TBI) while riding roller coasters has received substantial attention. Case reports of TBI around the time of riding roller coasters have led many medical professionals to assert that the high gravitational forces (G-forces) induced by roller coasters pose a significant TBI risk. Head injury research, however, has shown that G-forces alone cannot predict TBI. Established head injury criterions and procedures were employed to compare the potential of TBI between daily activities and roller coaster riding. Three-dimensional head motions were measured during 3 different roller coaster rides, a pillow fight, and car crash simulations. Data was analyzed and compared with published data, using similar analyses of head motions. An 8.05 m/s car crash lead to the largest head injury criterion measure of 28.1 and head impact power of 3.41, over 6 times larger than the roller coaster rides of 4.1 and 0.36. Notably, the linear and rotational components of head acceleration during roller coaster rides were milder than those induced by many common activities. As such, there appears to be an extremely low risk of TBI due to the head motions induced by roller coaster rides. PMID:19901817

  16. On the Stability of a Bicycle on Rollers

    ERIC Educational Resources Information Center

    Cleary, Patricia A.; Mohazzabi, Pirooz

    2011-01-01

    Riding a bicycle on the newest form of indoor training, rollers, presents a unique experiment on bicycle stability. The stability factors eliminated by riding on rollers are discussed in terms of refined handling and control of the centre of mass on a bicycle. This paper is intended for undergraduate physics majors as well as any other general…

  17. Head motions while riding roller coasters: Implications for brain injury

    PubMed Central

    Chickola, Larry; Smith, Douglas H.

    2009-01-01

    The risk of traumatic brain injury (TBI) while riding roller coasters has received substantial attention. Case reports of TBI around the time of riding roller coasters have led many medical professionals to assert that the high gravitational forces (G-forces) induced by roller coasters pose a significant TBI risk. Head injury research, however, has shown that G-forces alone cannot predict TBI. Established head injury criterions and procedures were employed to compare the potential of TBI between daily activities and roller coaster riding. Three dimensional head motions were measured during three different roller coaster rides, a pillow fight, and car crash simulations. Data was analyzed and compared to published data using similar analyses of head motions. An 8.05m/s car crash lead to the largest head injury criterion measure (HIC15) of 28.1 and head impact factor (HIP) of 3.41, over six times larger than the roller coaster rides of 4.1 and 0.36. Notably, the linear and rotational components of head acceleration during roller coaster rides were milder than those induced by many common activities. As such, there appears to be an extremely low risk of TBI due to the head motions induced by roller coaster rides. PMID:19901817

  18. Roller coaster related fatalities, United States, 1994–2004

    PubMed Central

    Pelletier, A; Gilchrist, J

    2005-01-01

    Objective: To determine the number of fatalities related to roller coasters and examine factors common to multiple incidents. Methods: A case was defined as the death of a person, which was associated with a roller coaster in the United States between 15 May 1994 and 14 May 2004. Cases were identified from four data sources: (1) Consumer Product Safety Commission, (2) Lexis-Nexis, (3) Medline, and (4) Saferparks. Results: Forty people, ranging in age from 7 to 77 years, were killed in 39 separate incidents. Twenty nine (73%) deaths occurred among roller coaster patrons. Eleven fatalities resulted from external causes related to injuries from falls or collisions. Eighteen people died from medical conditions that might have been caused or exacerbated by riding a roller coaster; 15 were the result of intracranial hemorrhages or cardiac problems. Eleven (28%) deaths involved employees; all were caused by injuries. Conclusions: Approximately four deaths annually in the United States are associated with roller coasters. Prevention of roller coaster fatalities is dependent on establishing an effective surveillance system for amusement ride injuries, engineering rides to better protect both patrons and employees, improving training and supervision of employees regarding safety precautions, and posting cautionary notices near roller coasters for people with specified medical conditions. Further research is needed on roller coaster related deaths resulting from intracranial hemorrhages and cardiac problems. PMID:16203841

  19. Neurologic complication after a roller coaster ride.

    PubMed

    Sa Leitao, Davi; Mendonca, Dercio; Iyer, Harish; Kao, Cheng-Kai

    2012-01-01

    Neurologic complications after roller coaster rides are uncommon but potentially catastrophic. Physicians should have a high index of suspicion and prompt appropriate investigation. A 22-year-old healthy African American man presented with a 2-day history of constant occipital headache associated with vertigo, nausea, vomiting, and ambulatory dysfunction. Physical examination showed gait ataxia, slight dysmetria, and vertical nystagmus. Magnetic resonance imaging (MRI) of the brain showed early subacute ischemic infarct in the right cerebellum in the distribution of the right posterior inferior cerebellar artery. Magnetic resonance angiography of the neck showed focal dissection of the right vertebral artery at C1 through C2 level. On subsequent questioning, the patient recollected riding a roller coaster 2 weeks before the onset of symptoms. Anticoagulation with heparin was started, and the patient was bridged to oral warfarin. After a 5-day uneventful hospital course, symptoms improved and patient was discharged on oral anticoagulation. Cervicocephalic arterial dissections after roller coaster rides are rarely described in literature. The acceleration and abrupt changes of direction might lead to indirect trauma that is applied to mobile portions of the cervicocephalic arteries leading to intimal tears. Magnetic resonance angiography combined with axial T1-weighted cervical MRI is preferred because it is a high-sensitive, noninvasive test. The rationale for the use of anticoagulants or antiplatelets in patients with cervicocephalic arterial dissection is to prevent early recurrence and infarction. However, a meta-analysis failed to show significant difference in the rates of disability or death between both groups. Therefore, the decision for medical treatment should be made in a case-by-case basis. PMID:20980120

  20. Lateral Stability Simulation of a Rail Truck on Roller Rig

    NASA Astrophysics Data System (ADS)

    Dukkipati, Rao V.

    The development of experimental facilities for rail vehicle testing is being complemented by analytic studies. The purpose of this effort has been to gain insight into the dynamics of rail vehicles in order to guide development of the Roller Rigs and to establish an analytic framework for the design and interpretation of tests to be conducted on Roller Rigs. The work described here represents initial efforts towards meeting these objectives. Generic linear models were developed of a freight car (with a characteristic North American three-piece truck) on tangent track. The models were developed using the generalized multi body dynamics software MEDYNA. Predictions were made of the theoretical linear model hunting (lateral stability) characteristics of the freight car, i. e., the critical speeds and frequencies, for five different configurations: (a) freight car on track, (b) the freight car's front truck on the roller stand and its rear truck on track, (c) freight car on the roller rig, (d) a single truck on track, and (e) single truck on the roller stand. These were compared with the Association of American Railroads' field test data for an 80-ton hopper car equipped with A-3 ride control trucks. Agreement was reached among all the analytical models, with all models indicating a range of hunting speeds of 2% from the highest to lowest. The largest discrepancy, approximately 6%, was indicated between the models and the field test data. Parametric study results using linear model of freight truck on the roller rig show that (a) increasing roller radius increases critical speed (b) increasing the wheel initial cone angle will decrease the hunting speed (c) increasing the roller cant increases hunting speed (d) decrowning of the wheelset on the rollers will not effect the hunting speed but induces longitudinal destabilizing horizontal forces at the contact and (e) lozenging of wheelset on the rollers induces a yaw moment and the hunting speed decreases with increasing

  1. 36 CFR 13.916 - Use of roller skates, skateboards, roller skis, in-line skates, and similar devices.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR NATIONAL PARK SYSTEM UNITS IN ALASKA Special Regulations-Denali National Park and Preserve General Provisions § 13.916 Use of roller skates... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Use of roller...

  2. Frequency coded sensors incorporating tapers

    NASA Technical Reports Server (NTRS)

    Hines, Jacqueline H. (Inventor); Solie, Leland P. (Inventor)

    2010-01-01

    A surface acoustic wave device includes a piezoelectric substrate on which is formed a transducer that generates acoustic waves on the surface of the substrate from electrical waves received by the transducer. The waves are carried along an acoustic track to either a second transducer or a reflector. The transducers or transducer and reflector are formed of subsections that are constructed to operate at mutually different frequencies. The subsections of at least one of the transducers or transducer and reflector are out of alignment with respect to one another relative to the transverse of the propagation direction. The out of aligned subsections provide not only a frequency component but also a time to the signal output signal. Frequency response characteristics are improved. An alternative embodiment provides that the transducers and/or reflectors are continuously tapered instead of having discrete frequency subsections.

  3. Endfire tapered slot antennas on dielectric substrates

    NASA Technical Reports Server (NTRS)

    Yngvesson, K. S.; Schaubert, D. H.; Korzeniowski, T. L.; Kollberg, E. L.; Thungren, T.

    1985-01-01

    Endfire-tapered slot antennas are suitable for many integrated circuit applications, imaging and phased arrays. An investigation of single elements of such antennas, including slots which are exponentially tapered (Vivaldi), linearly tapered, and constant width. For antennas of all types, a good general agreement is obtained for curves of beamwidth-versus-length, normalized to wavelength, when one compares the data with that for traveling-wave antennas published by Zucker (1961). An important condition for this agreement is that the effective dielectric thickness, defined in the text, is in a certain optimum range. This condition is qualitatively explained in terms of the theory for traveling-wave antennas.

  4. Tapered silicon nanowires for enhanced nanomechanical sensing

    NASA Astrophysics Data System (ADS)

    Malvar, O.; Gil-Santos, E.; Ruz, J. J.; Ramos, D.; Pini, V.; Fernandez-Regulez, M.; Calleja, M.; Tamayo, J.; San Paulo, A.

    2013-07-01

    We investigate the effect of controllably induced tapering on the resonant vibrations and sensing performance of silicon nanowires. Simple analytical expressions for the resonance frequencies of the first two flexural modes as a function of the tapering degree are presented. Experimental measurements of the resonance frequencies of singly clamped nanowires are compared with the theory. Our model is valid for any nanostructure with tapered geometry, and it predicts a reduction beyond two orders of magnitude of the mass detection limit for conical resonators as compared to uniform beams with the same length and diameter at the clamp.

  5. Elasto-plastic contact between rollers

    NASA Astrophysics Data System (ADS)

    Chu, Kunliang; Li, Penghui

    1991-12-01

    Knowledge of the three-dimensional contact stress between roller and rolling road for a strain- hardening material in an elasto-plastic state is limited, to say the least. Mathematical analyses of stress for this problem meet with extreme difficulties. Therefore, experimental approaches are desirable. The experimental elasto-plastic stress analysis method proposed by A. R. Hunter is extended in this investigation. The model material is epoxy resin, which exhibits a frozen nonlinear effective stress-strain behavior similar to that of bearing steel when subjected to a thermal cycle whose maximum temperature is significantly less than the critical temperature of the material. This effective stress-strain curve and an effective birefringence- stress curve were obtained by subjecting uniaxial tensile specimens to constant stress and the appropriate thermal cycle. Then the model was subjected to the same thermal cycle and a uniform distributed load that would develop a plastic zone. The stress distributions on the contact surface and the plastic-zone expansion law were obtained from photomechanical analysis of the slices removed from the model. Several important conclusions were summed up that would greatly improve the roller bearing design.

  6. 21 CFR 870.4370 - Roller-type cardiopulmonary bypass blood pump.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Roller-type cardiopulmonary bypass blood pump. 870... Roller-type cardiopulmonary bypass blood pump. (a) Identification. A roller-type cardiopulmonary bypass blood pump is a device that uses a revolving roller mechanism to pump the blood through...

  7. 21 CFR 870.4370 - Roller-type cardiopulmonary bypass blood pump.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Roller-type cardiopulmonary bypass blood pump. 870... Roller-type cardiopulmonary bypass blood pump. (a) Identification. A roller-type cardiopulmonary bypass blood pump is a device that uses a revolving roller mechanism to pump the blood through...

  8. 21 CFR 870.4370 - Roller-type cardiopulmonary bypass blood pump.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Roller-type cardiopulmonary bypass blood pump. 870... Roller-type cardiopulmonary bypass blood pump. (a) Identification. A roller-type cardiopulmonary bypass blood pump is a device that uses a revolving roller mechanism to pump the blood through...

  9. 21 CFR 870.4370 - Roller-type cardiopulmonary bypass blood pump.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Roller-type cardiopulmonary bypass blood pump. 870... Roller-type cardiopulmonary bypass blood pump. (a) Identification. A roller-type cardiopulmonary bypass blood pump is a device that uses a revolving roller mechanism to pump the blood through...

  10. Morse-type tapers: factors that may influence taper strength during total hip arthroplasty.

    PubMed

    Pennock, Andrew T; Schmidt, Andrew H; Bourgeault, Craig A

    2002-09-01

    We studied the effect of varying impaction force, repeated impactions, and fluid contamination on the disassembly strength of Morse-type tapers in 4 commercially available, modular femoral total hip components. The effect of varying techniques of taper assembly on the distraction force was studied. Our results show a reproducible and linear relationship between the taper impaction force and the disassembly force. The force necessary to separate the taper for a given impaction force varied, however, among manufacturers. Repeated impactions added little strength, and we found that when multiple impactions of varying force are used, the strength is roughly equivalent to the expected strength from the single strongest blow. Fluid contamination at the taper interface had unpredictable effects on taper strength.

  11. Long-period cascaded fiber taper filters.

    PubMed

    Martinez-Rios, A; Salceda-Delgado, G; Guerrero-Viramontes, J A

    2014-02-10

    Fiber filters based on periodic cascaded tapered fiber sections are demonstrated. The filters consist of up to seven tapered sections separated periodically by more than 3 mm from center to center, with nominal tapered sections of 1  mm×1  mm×1  mm longitudinal dimensions. The transmission spectrum consists of discrete notches, resembling those observed in long-period fiber gratings, which differs from the observed spectrum in Mach-Zender interferometers based on cascaded tapers. Its sensitivity to external perturbations, such as refractive index or mechanical stress, made the device potentially very useful as a sensor or tunable filter. PMID:24663276

  12. Tapered fiber based high power random laser.

    PubMed

    Zhang, Hanwei; Du, Xueyuan; Zhou, Pu; Wang, Xiaolin; Xu, Xiaojun

    2016-04-18

    We propose a novel high power random fiber laser (RFL) based on tapered fiber. It can overcome the power scaling limitation of RFL while maintaining good beam quality to a certain extent. An output power of 26.5 W has been achieved in a half-open cavity with one kilometer long tapered fiber whose core diameter gradually changes from 8 μm to 20 μm. The steady-state light propagation equations have been modified by taking into account the effective core area to demonstrate the tapered RFL through numerical calculations. The numerical model effectively describes the power characteristics of the tapered fiber based RFL, and both the calculating and experimental results show higher power exporting potential compared with the conventional single mode RFL. PMID:27137338

  13. Workplace for manufacturing devices based on optical fiber tapers

    NASA Astrophysics Data System (ADS)

    Martan, Tomáš; Honzátko, Pavel; Kaňka, Jiři; Novotný, Karel

    2007-04-01

    Many important optical fiber components are based on tapered optical fibers. A taper made from a single-mode optical fiber can be used, e.g., as a chemical sensor, bio-chemical sensor, or beam expander. A fused pair of tapers can be used as a fiber directional coupler. Fiber tapers can be fabricated in several simple ways. However, a tapering apparatus is required for more sophisticated fabrication of fiber tapers. The paper deals with fabrication and characterization of fiber tapers made from a single-mode optical fiber. A tapering apparatus was built for producing devices based on fiber tapers. The apparatus is universal and enables one to taper optical fibers of different types by a method utilizing stretching a flame-heated section of a silica fiber. Fiber tapers with constant waist length and different waist diameters were fabricated. The transition region of each fiber taper monotonically decreased in diameter along its length from the untapered fiber to the taper waist. The fiber tapers were fabricated with a constant drawing velocity, while the central zone of the original single-mode fiber was heated along a constant length. The spectral transmissions of the manufactured fiber tapers with different parameters were measured by the cut-back method.

  14. Chronic subdural haematoma after riding a roller coaster.

    PubMed

    Yamakami, Iwao; Mine, Seiichiro; Yamaura, Akira; Fukutake, Toshio

    2005-01-01

    We report a 20-year-old man who developed a chronic subdural haematoma (CSDH) after riding a "giant" roller coaster. The patient had a past history of a subdural hygroma, diagnosed six weeks after a motorcycle accident. Three months after this accident, he rode on a roller coaster, but suffered no direct head trauma during the ride. Three weeks later, he developed a CSDH requiring surgical evacuation. Roller coaster riding, associated with high velocities and extreme acceleration/deceleration forces is a modern cause of CSDH in the young, which may be increasing due to ever-faster rides. PMID:15639420

  15. Backscatter coefficient estimation using tapers with gaps.

    PubMed

    Luchies, Adam C; Oelze, Michael L

    2015-04-01

    When using the backscatter coefficient (BSC) to estimate quantitative ultrasound parameters such as the effective scatterer diameter (ESD) and the effective acoustic concentration (EAC), it is necessary to assume that the interrogated medium contains diffuse scatterers. Structures that invalidate this assumption can affect the estimated BSC parameters in terms of increased bias and variance and decrease performance when classifying disease. In this work, a method was developed to mitigate the effects of echoes from structures that invalidate the assumption of diffuse scattering, while preserving as much signal as possible for obtaining diffuse scatterer property estimates. Backscattered signal sections that contained nondiffuse signals were identified and a windowing technique was used to provide BSC estimates for diffuse echoes only. Experiments from physical phantoms were used to evaluate the effectiveness of the proposed BSC estimation methods. Tradeoffs associated with effective mitigation of specular scatterers and bias and variance introduced into the estimates were quantified. Analysis of the results suggested that discrete prolate spheroidal (PR) tapers with gaps provided the best performance for minimizing BSC error. Specifically, the mean square error for BSC between measured and theoretical had an average value of approximately 1.0 and 0.2 when using a Hanning taper and PR taper respectively, with six gaps. The BSC error due to amplitude bias was smallest for PR (Nω = 1) tapers. The BSC error due to shape bias was smallest for PR (Nω = 4) tapers. These results suggest using different taper types for estimating ESD versus EAC.

  16. Tapered plug foam spray apparatus

    NASA Technical Reports Server (NTRS)

    Allen, Peter B. (Inventor)

    1996-01-01

    A two-component foam spray gun is readily disassembled for cleaning. It includes a body (1) with reactant (12, 14) and purge gas (16) inlet ports. A moldable valve packing (32) inside the body has a tapered conical interior surface (142), and apertures which match the reactant ports. A valve/tip (40) has a conical outer surface (48) which mates with the valve packing (32). The valve/tip (40) is held in place by a moldable packing washer (34), held at non-constant pressure by a screw (36, 38). The interior of the valve/tip (40) houses a removable mixing chamber (50). The mixing chamber (50) has direct flow orifices (60) and an auxiliary flow path (58, 60) which ameliorate pressure surges. The spray gun can be disassembled for cleaning without disturbing the seal, by removing the valve/tip (40) to the rear, thereby breaking it free of the conical packing. Rotation of the valve/tip (40) relative to the body (1) shuts off the reactant flow, and starts the purge gas flow.

  17. 30. Elevator no. 3: top floor, rollers for southeast conveyor ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    30. Elevator no. 3: top floor, rollers for southeast conveyor belt flanked by top openings of grain bins, with tripper in background, facing northeast - Washburn Crosby Company Elevators No. 2 & 3, 900 & 1000 Second Avenue, South, Minneapolis, Hennepin County, MN

  18. 29. Elevator no. 3: top floor, conveyor belt rollers for ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    29. Elevator no. 3: top floor, conveyor belt rollers for belt to gangway (in background) connecting with elevator no. 2, facing northwest - Washburn Crosby Company Elevators No. 2 & 3, 900 & 1000 Second Avenue, South, Minneapolis, Hennepin County, MN

  19. 7. DETAIL VIEW OF DAM, SHOWING ROLLER GATES, GATE PIERS, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    7. DETAIL VIEW OF DAM, SHOWING ROLLER GATES, GATE PIERS, HEADHOUSES AND DAM BRIDGE, LOOKING NORTHWEST, UPSTREAM - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 9, Lynxville, Crawford County, WI

  20. 26. VIEW OF ROLLER GATE BULKHEADS AND BULKHEAD CARS IN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    26. VIEW OF ROLLER GATE BULKHEADS AND BULKHEAD CARS IN STORAGE YARD, WITH DAM BRIDGE OVERHEAD, LOOKING SOUTHEAST - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 9, Lynxville, Crawford County, WI

  1. 5. DETAIL VIEW OF DAM, SHOWING ROLLER AND TAINTER GATES, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    5. DETAIL VIEW OF DAM, SHOWING ROLLER AND TAINTER GATES, GATE PIERS, HEADHOUSES AND DAM BRIDGE, LOOKING NORTHWEST, UPSTREAM - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 9, Lynxville, Crawford County, WI

  2. Engine testing of ceramic cam-roller followers. Final report

    SciTech Connect

    Kalish, Y.

    1992-04-01

    For several years, DDC has been developing monolithic ceramic heat engine components. One of the components, developed for an application in our state-of-the-art on-highway, heavy-duty diesel engine, the Series 60, is a silicon nitride cam-roller follower. Prior to starting this program, each valve train component in the Series 60 was considered for conversion to a ceramic material. Many advantages and disadvantages (benefits and risks) were considered. From this effort, one component was selected, the cam-roller follower. Using a system design approach, a ceramic cam-roller follower offered functional improvement at a reasonable cost. The purpose of the project was to inspect and test 100 domestically produced silicon nitride cam-roller followers built to the requirements of the DDC series 60 engine.

  3. Engine testing of ceramic cam-roller followers

    SciTech Connect

    Kalish, Y. )

    1992-04-01

    For several years, DDC has been developing monolithic ceramic heat engine components. One of the components, developed for an application in our state-of-the-art on-highway, heavy-duty diesel engine, the Series 60, is a silicon nitride cam-roller follower. Prior to starting this program, each valve train component in the Series 60 was considered for conversion to a ceramic material. Many advantages and disadvantages (benefits and risks) were considered. From this effort, one component was selected, the cam-roller follower. Using a system design approach, a ceramic cam-roller follower offered functional improvement at a reasonable cost. The purpose of the project was to inspect and test 100 domestically produced silicon nitride cam-roller followers built to the requirements of the DDC series 60 engine.

  4. 14. INTERIOR VIEW OF HEADHOUSE, SHOWING ROLLER GATE GAUGE AND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. INTERIOR VIEW OF HEADHOUSE, SHOWING ROLLER GATE GAUGE AND WHEEL GEAR, LOOKING SOUTHEAST - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 8, On Mississippi River near Houston County, MN, Genoa, Vernon County, WI

  5. EVALUATION OF A LOW FRICTION - HIGH EFFICIENCY ROLLER BEARING ENGINE

    SciTech Connect

    Kolarik, Robert V. II; Shattuck, Charles W.; Copper, Anthony P.

    2009-06-30

    This Low Friction (High Efficiency Roller Bearing) Engine (LFE) report presents the work done by The Timken Company to conduct a technology demonstration of the benefits of replacing hydrodynamic bearings with roller bearings in the crankshaft and camshaft assemblies of an internal combustion engine for the purpose of collecting data sufficient to prove merit. The engines in the present study have been more extensively converted to roller bearings than any previous studies (40 needle roller bearings per engine) to gain understanding of the full potential of application of bearing technology. The project plan called for comparative testing of a production vehicle which was already respected for having demonstrated low engine friction levels with a rollerized version of that engine. Testing was to include industry standard tests for friction, emissions and fuel efficiency conducted on instrumented dynamometers. Additional tests for fuel efficiency, cold start resistance and other measures of performance were to be made in the actual vehicle. Comparative measurements of noise, vibration and harshness (NVH), were planned, although any work to mitigate the suspected higher NVH level in the rollerized engine was beyond the scope of this project. Timken selected the Toyota Avalon with a 3.5L V-6 engine as the test vehicle. In an attempt to minimize cost and fabrication time, a ‘made-from’ approach was proposed in which as many parts as possible would be used or modified from production parts to create the rollerized engine. Timken commissioned its test partner, FEV Engine Technology, to do a feasibility study in which they confirmed that using such an approach was possible to meet the required dimensional restrictions and tolerances. In designing the roller bearing systems for the crank and cam trains, Timken utilized as many production engine parts as possible. The crankshafts were produced from production line forgings, which use Timken steel, modified with special

  6. Design and Realization Of Roller Mill Control System

    NASA Astrophysics Data System (ADS)

    Wang, QianHong; Zhang, Qiang; Bai, XiaoLi; Yu, HongLiang

    a Distributed Control System(DCS) of cement raw materials is presented for the vertical roller mill by the application of ABB's IndustrialIT. The results demonstrate the practical application of the system's utility and effectiveness and reliability.

  7. 25. VIEW OF ROLLER GATE BULKHEADS, WITH BULKHEAD CARS AND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    25. VIEW OF ROLLER GATE BULKHEADS, WITH BULKHEAD CARS AND TRACKS IN STORAGE YARD, WITH DAM BRIDGE OVERHEAD, LOOKING EAST - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 4, Alma, Buffalo County, WI

  8. 3. DETAIL VIEW OF DAM, SHOWING ROLLER AND TAINTER GATES, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. DETAIL VIEW OF DAM, SHOWING ROLLER AND TAINTER GATES, GATE PIERS, HEADHOUSES AND DAM BRIDGES, LOOKING SOUTH, DOWNSTREAM - Upper Mississippi River 9-Foot Channel, Lock & Dam No. 4, Alma, Buffalo County, WI

  9. 17. Detail showing roller nest for vertical strut sitting atop ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    17. Detail showing roller nest for vertical strut sitting atop granite pier cap. View to southwest. - Selby Avenue Bridge, Spanning Short Line Railways track at Selby Avenue between Hamline & Snelling Avenues, Saint Paul, Ramsey County, MN

  10. GENERAL VIEW OF EAST SIDE LOOKING WEST, ROLLER DAM AND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    GENERAL VIEW OF EAST SIDE LOOKING WEST, ROLLER DAM AND RURAL ELECTRICAL FACILITY IN FOREGROUND AND CURRENT HIGHWAY 151 BRIDGE IN BACKGROUND. - Wapsipinicon River Bridge, Spanning Wapsipinicon River at former State Highway 151, Anamosa, Jones County, IA

  11. 15. VIEW OF NORTHWEST BEARING SEAT WITH EXPANSION ROLLERS ON ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    15. VIEW OF NORTHWEST BEARING SEAT WITH EXPANSION ROLLERS ON NORTHERN PIER; FACING SOUTHEAST. - Walker Bridge, Spanning Klamath River and connecting Highway 96 and Walker Road, Klamath River, Siskiyou County, CA

  12. 18. VIEW OF ROLLER LEVELER USED TO STRAIGHTEN AND FLATTEN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    18. VIEW OF ROLLER LEVELER USED TO STRAIGHTEN AND FLATTEN METAL SHEETS. (7/2/86) - Rocky Flats Plant, Uranium Rolling & Forming Operations, Southeast section of plant, southeast quadrant of intersection of Central Avenue & Eighth Street, Golden, Jefferson County, CO

  13. Rotary roller of no. 2 seamless line in bays 19 ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Rotary roller of no. 2 seamless line in bays 19 and 20 of the main pipe mill building looking north. - U.S. Steel National Tube Works, Main Pipe Mill Building, Along Monongahela River, McKeesport, Allegheny County, PA

  14. 14. UPPER SHOES, FIXED SHOES, ROLLER SHOES, CENTER WEB, AND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. UPPER SHOES, FIXED SHOES, ROLLER SHOES, CENTER WEB, AND ROLLER BED PLATES. (Also includes a sheet index and a schedule of parts). American Bridge Company, Ambridge Plant No. 5, sheet no. 4, dated April 7, 1928, order no. F5073. For U.S. Steel Products Company, Pacific Coast Depot, order no. SF578. For Southern Pacific Company, order no. 8873-P-28746. various scales. - Napa River Railroad Bridge, Spanning Napa River, east of Soscol Avenue, Napa, Napa County, CA

  15. 26. Detail view of drum girder with rollers below, resting ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    26. Detail view of drum girder with rollers below, resting on fixed turntable upon masonry center pier. Swing drive shaft (vertical) is turned by level gear of horizontal shaft (protruding through machine room wall), which turns pinion gear toothed to fixed turntable rack below rollers. (Nov. 25, 1988) - University Heights Bridge, Spanning Harlem River at 207th Street & West Harlem Road, New York County, NY

  16. A study on rheological characteristics of roller milled fenugreek fractions.

    PubMed

    Sakhare, Suresh D; Inamdar, Aashitosh A; Prabhasankar, P

    2016-01-01

    Fenugreek seeds were fractionated by roller milling to get various fractions. The roller milled fractions and whole fenugreek flour (WFF) were evaluated for the flow behavior and time-dependent flow properties using a rotational viscometer at the temperatures of 10-60 (0)C. The samples subjected to a programmed shear rate increase linearly from 0 to 300 s(-1) in 3 min and successive decrease linearly shear rate from 300 s(-1) to 0 in 3 min. The roller milled fractions and WFF paste exhibited non-Newtonian pseudoplastic behavior. Difference in hysteresis loop area was observed among the roller milled fractions and WFF, being more noticeable at lower temperatures. Power law and Casson models were used to predict flow properties of samples. The power law model described well the flow behavior of the roller milled fractions and WFF at temperatures tested. Except flour (FL) fraction, consistency coefficient, m, increased with the temperature both in the forward and backward measurements. The roller milled fractions and WFF exhibited rheopectic behavior that increased viscosity with increasing the shear speed and the temperature. For all the sample tested, initial shear stress increased with increase in shear rate and temperature. PMID:26787961

  17. Rotational flow in tapered slab rocket motors

    NASA Astrophysics Data System (ADS)

    Saad, Tony; Sams, Oliver C.; Majdalani, Joseph

    2006-10-01

    Internal flow modeling is a requisite for obtaining critical parameters in the design and fabrication of modern solid rocket motors. In this work, the analytical formulation of internal flows particular to motors with tapered sidewalls is pursued. The analysis employs the vorticity-streamfunction approach to treat this problem assuming steady, incompressible, inviscid, and nonreactive flow conditions. The resulting solution is rotational following the analyses presented by Culick for a cylindrical motor. In an extension to Culick's work, Clayton has recently managed to incorporate the effect of tapered walls. Here, an approach similar to that of Clayton is applied to a slab motor in which the chamber is modeled as a rectangular channel with tapered sidewalls. The solutions are shown to be reducible, at leading order, to Taylor's inviscid profile in a porous channel. The analysis also captures the generation of vorticity at the surface of the propellant and its transport along the streamlines. It is from the axial pressure gradient that the proper form of the vorticity is ascertained. Regular perturbations are then used to solve the vorticity equation that prescribes the mean flow motion. Subsequently, numerical simulations via a finite volume solver are carried out to gain further confidence in the analytical approximations. In illustrating the effects of the taper on flow conditions, comparisons of total pressure and velocity profiles in tapered and nontapered chambers are entertained. Finally, a comparison with the axisymmetric flow analog is presented.

  18. Spherical roller bearing analysis. SKF computer program SPHERBEAN. Volume 1: Analysis

    NASA Technical Reports Server (NTRS)

    Kleckner, R. J.; Pirvics, J.

    1980-01-01

    The models and associated mathematics used within the SPHERBEAN computer program for prediction of the thermomechanical performance characteristics of high speed lubricated double row spherical roller bearings are presented. The analysis allows six degrees of freedom for each roller and three for each half of an optionally split cage. Roller skew, free lubricant, inertial loads, appropriate elastic and friction forces, and flexible outer ring are considered. Roller quasidynamic equilibrium is calculated for a bearing with up to 30 rollers per row, and distinct roller and flange geometries are specifiable. The user is referred to the material contained here for formulation assumptions and algorithm detail.

  19. Tapered polysilicon core fibers for nonlinear photonics.

    PubMed

    Suhailin, Fariza H; Shen, Li; Healy, Noel; Xiao, Limin; Jones, Maxwell; Hawkins, Thomas; Ballato, John; Gibson, Ursula J; Peacock, Anna C

    2016-04-01

    We propose and demonstrate a novel approach to obtaining small-core polysilicon waveguides from the silicon fiber platform. The fibers were fabricated via a conventional drawing tower method and, subsequently, tapered down to achieve silicon core diameters of ∼1  μm, the smallest optical cores for this class of fiber to date. Characterization of the material properties have shown that the taper process helps to improve the local crystallinity of the silicon core, resulting in a significant reduction in the material loss. By exploiting the combination of small cores and low losses, these tapered fibers have enabled the first observation of nonlinear transmission within a polycrystalline silicon waveguide of any type. As the fiber drawing method is highly scalable, it opens a route for the development of low-cost and flexible nonlinear silicon photonic systems. PMID:27192236

  20. Turbine airfoil fabricated from tapered extrusions

    DOEpatents

    Marra, John J

    2013-07-16

    An airfoil (30) and fabrication process for turbine blades with cooling channels (26). Tapered tubes (32A-32D) are bonded together in a parallel sequence, forming a leading edge (21), a trailing edge (22), and pressure and suction side walls (23, 24) connected by internal ribs (25). The tapered tubes may be extruded without camber to simplify the extrusion process, then bonded along matching surfaces (34), forming a non-cambered airfoil (28), which may be cambered in a hot forming process and cut (48) to length. The tubes may have tapered walls that are thinner at the blade tip (T1) than at the base (T2), reducing mass. A cap (50) may be attached to the blade tip. A mounting lug (58) may be forged (60) on the airfoil base and then machined, completing the blade for mounting in a turbine rotor disk.

  1. Holland Roller Windmill: investigation and demonstration of principles. Final report

    SciTech Connect

    Holland, R. Jr.

    1981-06-01

    A horizontal axis wind power machine using a radially positioned spinning cylindrical roller was investigated and a demonstration machine was constructed and operated in the natural wind. Earlier wind machines using the Magnus rotor were reviewed, such as the Flettner Rotor Windmill and the Madaras Rotor Power Plant. Wind tunnel tests and analyses were made. Analyses were made of gyroscopic bending moments on the roller and centrifugal hinge moments acting on the freely hinged trailer. Analyses of applied structural air loads were made of the conventional torsionally restrained airfoil type blade compared to the unconventional blade consisting of roller and free trailer. Criteria for stress analysis of trailer blades were developed. Exploratory wind tunnel tests were made of the downwash patterns around Magnus rotors. The power required to spin them was measured. Combined spinning and whirling of a model horizontal axis roller machine was demonstrated. Tests of blade type models were run. Sections for roller mill blades, consisting of power driven spinning roller and a series of trailers of varying sizes and shapes, were tested. Reynolds number effects on section performance were studied, and broadly suitable types of roller trailer combinations were determined below the critical and above the critical Reynolds. A design was synthesized for a single bladed demonstrator machine, including stress analysis, detail design, construction and assembly. The demonstrator operated satisfactorily in the natural wind. Results indicate that major benefits of this type of machine are virtual elimination of stresses due to gusts and strong winds, and marked reduction of cost per unit of swept disk area.

  2. Tapered Velocity Couplers and Devices: a Treatise

    NASA Astrophysics Data System (ADS)

    Kim, Hyoun Soo

    A polarization independent device is highly desirable for use in single-mode fiber optical communication systems. Tapered velocity coupler (TVC) is expected to play an important role since its operation is polarization independent as well as wavelength insensitive. Thus far, TVC has received little attention primarily because of the unusually long device length required for complete power transfer. In this dissertation we establish that a TVC with an acceptable device length for integration can be indeed realized and integrated by tapering in index as well as in dimension. We demonstrate, for the first time, that complete power transfer can be achieved in a tapered, both in index and in dimension, velocity coupler in Ti:LiNbO _3 with device length reduced to one quarter of that of conventional TVC. The coupler is analyzed by use of step transition model in conjunction with local normal modes of the grade index TVC, overcoming the deficiency of the five-layer step index model. We further demonstrate a Ti:LiNbO_3 digital optical switch with the smallest voltage length product reported to date, namely, 7.2 Vcm for TM and 24 Vcm TE mode with a 15 dB cross talk. In an effort to extend the tapered, both in index and in dimension, velocity coupler concepts to step index compound semiconductor waveguides, we introduce proton exchanged periodically segmented (PEPS) waveguides. PEPS waveguides in LiNbO_3 are first studied theoretically and experimentally. The mode index of PEPS waveguides increases linearly and saturates finally with increase of duty cycle. Next, segmented waveguides in AlGaAs/GaAs are characterized in terms of propagation loss and modal size with respect to duty cycle. These segmented waveguides will be utilized in the development of step index tapered velocity couplers. Finally, we present an application for TVC as an optical interconnect. In particular, a tapered waveguide interconnect between a single quantum well (SQW) laser and a multi-quantum well

  3. 48 CFR 225.7009 - Restriction on ball and roller bearings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Restriction on ball and roller bearings. 225.7009 Section 225.7009 Federal Acquisition Regulations System DEFENSE ACQUISITION... roller bearings....

  4. 48 CFR 225.7009 - Restriction on ball and roller bearings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Restriction on ball and roller bearings. 225.7009 Section 225.7009 Federal Acquisition Regulations System DEFENSE ACQUISITION... roller bearings....

  5. 48 CFR 225.7009 - Restriction on ball and roller bearings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Restriction on ball and roller bearings. 225.7009 Section 225.7009 Federal Acquisition Regulations System DEFENSE ACQUISITION... roller bearings....

  6. 48 CFR 225.7009 - Restriction on ball and roller bearings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 3 2014-10-01 2014-10-01 false Restriction on ball and roller bearings. 225.7009 Section 225.7009 Federal Acquisition Regulations System DEFENSE ACQUISITION... roller bearings....

  7. 48 CFR 225.7009 - Restriction on ball and roller bearings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Restriction on ball and roller bearings. 225.7009 Section 225.7009 Federal Acquisition Regulations System DEFENSE ACQUISITION... roller bearings....

  8. Pressure pulsation in roller pumps: a validated lumped parameter model.

    PubMed

    Moscato, Francesco; Colacino, Francesco M; Arabia, Maurizio; Danieli, Guido A

    2008-11-01

    During open-heart surgery roller pumps are often used to keep the circulation of blood through the patient body. They present numerous key features, but they suffer from several limitations: (a) they normally deliver uncontrolled pulsatile inlet and outlet pressure; (b) blood damage appears to be more than that encountered with centrifugal pumps. A lumped parameter mathematical model of a roller pump (Sarns 7000, Terumo CVS, Ann Arbor, MI, USA) was developed to dynamically simulate pressures at the pump inlet and outlet in order to clarify the uncontrolled pulsation mechanism. Inlet and outlet pressures obtained by the mathematical model have been compared with those measured in various operating conditions: different rollers' rotating speed, different tube occlusion rates, and different clamping degree at the pump inlet and outlet. Model results agree with measured pressure waveforms, whose oscillations are generated by the tube compression/release mechanism during the rollers' engaging and disengaging phases. Average Euclidean Error (AEE) was 20mmHg and 33mmHg for inlet and outlet pressure estimates, respectively. The normalized AEE never exceeded 0.16. The developed model can be exploited for designing roller pumps with improved performances aimed at reducing the undesired pressure pulsation.

  9. Evaluation of Wear between Pin and Bush in Roller Chain

    NASA Astrophysics Data System (ADS)

    Noguchi, Shoji; Yoshiba, Hideaki; Nakayama, Satoshi; Kanada, Tohru

    A roller chain is a typical machine element used in bicycles, motorcycles and many other devices for power transmission. The life of a roller chain is determined by elongation. As a rule of thumb, a chain begins to skip cogs on the sprocket wheel when the percentage of elongation reaches approximately 3%. Mechanical wear between pins and bushes causes elongation of the roller chain. However, research on the evaluation of wear of the roller chain is rare and the achievement is unstated. We describe the following initiatives in the study of wear between pins and bushes of a roller chain: (1) development of a wear tester using only two chain links, (2) establishment of a specific evaluation method using a roundness tester, and (3) causal explanation of non-uniform wear using the finite-element method (FEM). The experimental results show that pins and bushes are not in contact at the centerline, and that wear occurs exclusively at the tips of the pins owing to the bending deformation under the condition of tensile load.

  10. Net efficiency of roller skiing with a diagonal stride.

    PubMed

    Nakai, Akira; Ito, Akira

    2011-02-01

    The aims of this study were: (a) to determine net efficiency during roller skiing with a diagonal stride at various speeds; (b) to assess the development of net efficiency across speeds; and (c) to examine the characteristics of efficiency in diagonal roller skiing. Two-dimensional kinematics and oxygen uptake were determined in eight male collegiate cross-country ski athletes who roller skied with the diagonal stride at various speeds on a level track. Net efficiency was calculated from rates of internal and external work and net energy expenditure. Individual net efficiency ranged from 17.7% to 52.1%. Net efficiency in the entire group of athletes increased with increasing speed, reached a maximum value of 37.3% at 3.68 m · s(-1), before slowly decreasing. These findings indicate that roller skiing with the diagonal stride at high speed is a highly efficient movement and that an optimal speed exists at which net efficiency can be maximally enhanced in diagonal roller skiing.

  11. Cutting a Tapered Edge on Padding Material

    NASA Technical Reports Server (NTRS)

    Mitchell, M. J.

    1982-01-01

    Resilience and flexibility of felt, rubber, or other padding materials allow them to be clamped in form block, cut straight down, and then released to produce straight clean tapered edge. With material held in slanted position, edge can be cut straight down; hence cut depth is minimum.

  12. Radiation losses of step-tapered channel waveguides.

    PubMed

    Marcuse, D

    1980-11-01

    We compute the radiation losses of a rectangular dielectric waveguide (integrated optics channel waveguide) that is tapered so that its wider cross-sectional dimension increases by roughly a factor of three while its narrow dimension remains constant. As the waveguide widens its refractive index decreases to ensure that the waveguide supports only one guided mode. The taper is approximated by a discontinuous staircase curve. A rectangular waveguide taper of 2-microm thickness, tapering from 3- to 10-microm width through fourteen steps of 0.25-microm height, has a minimum loss (at 0.6328-microm wavelength) of 0.13 dB for a 200-microm taper length.

  13. 48 CFR 252.225-7016 - Restriction on acquisition of ball and roller bearings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... of ball and roller bearings. 252.225-7016 Section 252.225-7016 Federal Acquisition Regulations System... and roller bearings. As prescribed in 225.7009-5, use the following clause: RESTRICTION ON ACQUISITION OF BALL AND ROLLER BEARINGS (JUN 2011) (a) Definitions. As used in this clause— (1) Bearing...

  14. 48 CFR 252.225-7016 - Restriction on acquisition of ball and roller bearings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... of ball and roller bearings. 252.225-7016 Section 252.225-7016 Federal Acquisition Regulations System... and roller bearings. As prescribed in 225.7009-5, use the following clause: Restriction on Acquisition of Ball and Roller Bearings (MAR 2006) (a) Definitions. As used in this clause' (1)...

  15. 48 CFR 252.225-7016 - Restriction on acquisition of ball and roller bearings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... of ball and roller bearings. 252.225-7016 Section 252.225-7016 Federal Acquisition Regulations System... and roller bearings. As prescribed in 225.7009-5, use the following clause: Restriction on Acquisition of Ball and Roller Bearings (JUN 2011) (a) Definitions. As used in this clause— (1) Bearing...

  16. 48 CFR 252.225-7016 - Restriction on acquisition of ball and roller bearings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... of ball and roller bearings. 252.225-7016 Section 252.225-7016 Federal Acquisition Regulations System... and roller bearings. As prescribed in 225.7009-5, use the following clause: Restriction on Acquisition of Ball and Roller Bearings (JUN 2011) (a) Definitions. As used in this clause— (1) Bearing...

  17. 48 CFR 252.225-7016 - Restriction on acquisition of ball and roller bearings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... of ball and roller bearings. 252.225-7016 Section 252.225-7016 Federal Acquisition Regulations System... and roller bearings. As prescribed in 225.7009-5, use the following clause: Restriction on Acquisition of Ball and Roller Bearings (JUN 2011) (a) Definitions. As used in this clause— (1) Bearing...

  18. 21 CFR 870.4370 - Roller-type cardiopulmonary bypass blood pump.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Roller-type cardiopulmonary bypass blood pump. 870... Roller-type cardiopulmonary bypass blood pump. (a) Identification. A roller-type cardiopulmonary bypass... cardiopulmonary bypass circuit during bypass surgery. (b) Classification. Class II (performance standards)....

  19. Evolution of a Hybrid Roller Cone/PDC core bit

    SciTech Connect

    Pettitt, R.; Laney, R.; George, D.; Clemens, G.

    1980-01-01

    The development of the hot dry rock (HDR) geothermal resource, as presently being accomplished by the Los Alamos Scientific Laboratory (LASL), requires that sufficient quantities of good quality core be obtained at a reasonable cost. The use of roller cone core bits, with tungsten carbide inserts, was initiated by the Deep Sea Drilling Program. These bits were modified for continental drilling in deep, hot, granitic rock for the LASL HDR Geothermal Site at Fenton Hill, New Mexico in 1974. After the advent of monocrystalline diamond Stratapax pads, a prototype hybrid roller cone/Stratapax core bit was fabricated by Smith Tool, and tested at Fenton Hill in 1978. During the drilling for a deeper HDR reservoir system in 1979 and 1980, six of the latest generation of these bits, now called Hybrid Roller Cone/Polycrystalline Diamond Cutter (PDC) core bits, were successfully used in granitic rock at depths below 11,000 ft.

  20. 77 FR 32522 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-06-01

    ..., 76 FR 45777 (August 1, 2011) (``Initiation Notice''). The Department preliminary determines that GGB... Unfinished, From the People's Republic of China, 52 FR 22667 (June 15, 1987) (``TRBs Notice of Antidumping... Review and Rescission of New Shipper Review, 67 FR 11283 (March 13, 2002)). The Department...

  1. 77 FR 2271 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-17

    ... and Intent To Rescind Administrative Review, in Part, 76 FR 41207 (July 13, 2011) ] (``Preliminary... Limit for the Final Results of the Antidumping Duty Administrative Review, 76 FR 69241 (November 8, 2011... Antidumping Duty Administrative Review, 76 FR 76360 (December 7, 2011). Analysis of Comments Received...

  2. 76 FR 3086 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-19

    ...: Preliminary Results of the 2008-2009 Administrative Review of the Antidumping Duty Order, 75 FR 41148 (July 15... Limit for the Final Results of the 2008-2009 Administrative Review of the Antidumping Duty Order, 75 FR... Results of the 2008-2009 Administrative Review of the Antidumping Duty Order, 75 FR 72801 (November...

  3. 78 FR 34985 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-11

    ... Initiation Notice, 77 FR at 45340. In September 2012, we received comments \\4\\ from Shanghai General Bearing... Investigation; Opportunity To Request Administrative Review, 77 FR 32528 (June 1, 2012). \\2\\ See Initiation of Antidumping and Countervailing Duty Administrative Reviews and Request for Revocation in Part, 77 FR...

  4. 78 FR 3396 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-16

    ..., 73 FR 8273, 8279 (February 13, 2008) (unchanged in Wooden Bedroom Furniture from the People's... Administrative Review, Rescission In Part, and Intent To Rescind in Part, 77 FR 40579 (July 10, 2012.... (``Haining Automann''); and (5) Zhejiang Zhaofeng Mechanical and Electronic Co., Ltd. (``Zhejiang...

  5. 76 FR 41207 - Tapered Roller Bearings and Parts Thereof, Finished or Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-13

    ... Duty Administrative Review, 76 FR 3086 (January 19, 2011). Surrogate Country Section 773(c)(1) of the... FR 22667 (June 15, 1987). \\2\\ See Antidumping or Countervailing Duty Order, Finding, or Suspended Investigation; Opportunity To Request Administrative Review, 75 FR 30383 (June 1, 2010). On July 28, 2010,...

  6. 77 FR 24179 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-23

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE... Order AGENCY: Import Administration, International Trade Administration, Department of Commerce. DATES: Effective Date: April 23, 2012. SUMMARY: On January 17, 2012, the Department of Commerce...

  7. 78 FR 40692 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-08

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE... Commerce. SUMMARY: The Department of Commerce (Department) is conducting an administrative review and two... for individual examination (i.e., Changshan Peer Bearing Co. Ltd. (CPZ/SKF)). The NSRs cover...

  8. 78 FR 58996 - Tapered Roller Bearings from the People's Republic of China: Notice of Court Decision Not in...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-25

    ...: Final Results of Antidumping Duty Administrative Review, 74 FR 3987 (January 22, 2009) (``Final Results...) (``Timken''), as clarified by Diamond Sawblades Mfrs. Coalition v. United States, 626 F.3d 1374 (Fed....

  9. 77 FR 40579 - Tapered Roller Bearings and Parts Thereof, Finished or Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-10

    ... Sales at Less Than Fair Value: Sparklers from the People's Republic of China, 56 FR 20588 (May 6, 1991... Carbide from the People's Republic of China, 59 FR 22585 (May 2, 1994) (``Silicon Carbide''). However, if... Determination of Sales at Less Than Fair Value: Furfuryl Alcohol From the People's Republic of China, 60...

  10. 77 FR 65668 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-30

    ... Decision Memorandum at Comment 3. We have recalculated surrogate financial ratios using different financial... Shipper Review, 77 FR 32522 (June 1, 2012) (``Preliminary Results''). FOR FURTHER INFORMATION CONTACT... eligible for a separate rate. \\9\\ See Preliminary Results, 77 FR at 32523-24. Final Results of the...

  11. 75 FR 41148 - Tapered Roller Bearings and Parts Thereof, Finished or Unfinished, From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-15

    ... Republic of China, 52 FR 22667 (June 15, 1987). \\2\\ See Antidumping or Countervailing Duty Order, Finding, or Suspended Investigation; Opportunity To Request Administrative Review, 74 FR 26202 (June 1, 2009... Antidumping and Countervailing Duty Administrative Reviews and Deferral of Administrative Review, 74 FR...

  12. Analysis of roller hemming process for a vehicle tailgate closure

    NASA Astrophysics Data System (ADS)

    Gürgen, Selim; Gökler, Mustafa İlhan; Darendeliler, Haluk; Çelikkaya, Çetin Cengiz; Erden, Kemal

    2013-05-01

    Hemming is a sheet metal joining process which is widely used for vehicle closures. As the latest hemming process type, the roller hemming process uses industrial robots therefore; main advantage of the process is achieved as flexibility with improved product quality. Trial and error method is the general approach to design the process in the industry due to limited know-how in the roller hemming. However, due to advantages of the process, the recent studies have also been focused on numerical simulations. In this study, the roller hemming process of the tailgate of a vehicle has been investigated by using the finite element method. The points of interest are selected as cycle time reduction and reducing the undesired wrinkling formation in the process. In the current roller hemming process of the tailgate, three stages including two pre-hemming and one final hemming stages are being applied. For the cycle time reduction, simulations have been performed to complete the hemming process in two stages. Effects of the roller geometry and the bending angle pairs have been investigated. The hemming process with two stages has been shown numerically to be applicable by considering the final geometry of the product and the maximum stress and strain values occurred during the process. The wrinkling formation is reduced by using a roller with larger diameter in the simulations. Then, verifications of the simulations have been done by implementing of the process. As a result of the study, approximately 33% reduction in the cycle time and 50% increase in the productivity of the tailgate have been successfully achieved in addition to reduction in the wrinkling formation during the pre-hemming stage.

  13. Dropping a particle out of a roller coaster

    NASA Astrophysics Data System (ADS)

    Mungan, Carl E.; Lipscombe, Trevor C.

    2014-07-01

    A rider in a roller coaster lets go of a particle such as a small marble. How far does the marble travel horizontally from the point of release before hitting the ground, assuming the speed of the roller coaster is determined by conservation of mechanical energy starting from the highest hill up which it was pulled? Where should the marble be released along the track if one wishes to maximize the range of the marble? These questions constitute interesting variations on conventional problems in two-dimensional kinematics, appropriate for an undergraduate course in classical mechanics. Exploration of various shapes of tracks could form interesting student projects for numerical or experimental investigation.

  14. Rollers in low-head dams - Challenges and solutions

    NASA Astrophysics Data System (ADS)

    Zamankhan, Piroz

    2012-12-01

    Low-head dams exist in many rivers for the purposes of diverting water for open-channel irrigation and providing power plants with cooling water. Flow over low-head dams is quite complex and dangerous rollers often develop down-stream that tend to trap and submerge floating objects. This paper presents an analysis of the problem based on physical and computational fluid dynamics (CFD) modeling and the result of this analysis in the form of design suggestions intended to diminish the hazards associated with rollers.

  15. The Effect of Taper Angle and Spline Geometry on the Initial Stability of Tapered, Splined Modular Titanium Stems.

    PubMed

    Pierson, Jeffery L; Small, Scott R; Rodriguez, Jose A; Kang, Michael N; Glassman, Andrew H

    2015-07-01

    Design parameters affecting initial mechanical stability of tapered, splined modular titanium stems (TSMTSs) are not well understood. Furthermore, there is considerable variability in contemporary designs. We asked if spline geometry and stem taper angle could be optimized in TSMTS to improve mechanical stability to resist axial subsidence and increase torsional stability. Initial stability was quantified with stems of varied taper angle and spline geometry implanted in a foam model replicating 2cm diaphyseal engagement. Increased taper angle and a broad spline geometry exhibited significantly greater axial stability (+21%-269%) than other design combinations. Neither taper angle nor spline geometry significantly altered initial torsional stability. PMID:25754255

  16. Wear of Steel and Ti6Al4V Rollers in Vacuum

    NASA Technical Reports Server (NTRS)

    Krantz, Timothy L.; Shareef, Iqbal

    2012-01-01

    This investigation was prompted by results of a qualification test of a mechanism to be used for the James Webb Space Telescope. Post-test inspections of the qualification test article revealed some loose wear debris and wear of the steel rollers and the mating Ti6Al4V surfaces. An engineering assessment of the design and observations from the tested qualification unit suggested that roller misalignment was a controlling factor. The wear phenomena were investigated using dedicated laboratory experiments. Tests were done using a vacuum roller rig for a range of roller misalignment angles. The wear in these tests was mainly adhesive wear. The measured wear rates were highly correlated to the misalignment angle. For all tests with some roller misalignment, the steel rollers lost mass while the titanium rollers gained mass indicating strong adhesion of the steel with the titanium alloy. Inspection of the rollers revealed that the adhesive wear was a two-way process as titanium alloy was found on the steel rollers and vice versa. The qualification test unit made use of 440F steel rollers in the annealed condition. Both annealed 440F steel rollers and hardened 440C rollers were tested in the vacuum roller rig to investigate possibility to reduce wear rates and the risk of loose debris formation. The 440F and 440C rollers had differing wear behaviors with significantly lesser wear rates for the 440C. For the test condition of zero roller misalignment, the adhesive wear rates were very low, but still some loose debris was formed

  17. Transverse Emittance Reduction with Tapered Foil

    SciTech Connect

    Jiao, Yi; Chao, Alex; Cai, Yunhai; /SLAC

    2011-12-09

    The idea of reducing transverse emittance with tapered energy-loss foil is proposed by J.M. Peterson in 1980s and recently by B. Carlsten. In this paper, we present the physical model of tapered energy-loss foil and analyze the emittance reduction using the concept of eigen emittance. The study shows that, to reduce transverse emittance, one should collimate at least 4% of particles which has either much low energy or large transverse divergence. The multiple coulomb scattering is not trivial, leading to a limited emittance reduction ratio. Small transverse emittances are of essential importance for the accelerator facilities generating free electron lasers, especially in hard X-ray region. The idea of reducing transverse emittance with tapered energy-loss foil is recently proposed by B. Carlsten [1], and can be traced back to J.M. Peterson's work in 1980s [2]. Peterson illustrated that a transverse energy gradient can be produced with a tapered energy-loss foil which in turn leads to transverse emittance reduction, and also analyzed the emittance growth from the associated multiple coulomb scattering. However, what Peterson proposed was rather a conceptual than a practical design. In this paper, we build a more complete physical model of the tapered foil based on Ref. [2], including the analysis of the transverse emittance reduction using the concept of eigen emittance and confirming the results by various numerical simulations. The eigen emittance equals to the projected emittance when there is no cross correlation in beam's second order moments matrix [3]. To calculate the eigen emittances, it requires only to know the beam distribution at the foil exit. Thus, the analysis of emittance reduction and the optics design of the subsequent beam line section can be separated. In addition, we can combine the effects of multiple coulomb scattering and transverse energy gradient together in the beam matrix and analyze their net effect. We find that,when applied to an

  18. Roller-gear drives for robotic manipulators design, fabrication and test

    NASA Technical Reports Server (NTRS)

    Anderson, William J.; Shipitalo, William

    1991-01-01

    Two single axis planetary roller-gear drives and a two axis roller-gear drive with dual inputs were designed for use as robotic transmissions. Each of the single axis drives is a two planet row, four planet arrangement with spur gears and compressively loaded cylindrical rollers acting in parallel. The two axis drive employs bevel gears and cone rollers acting in parallel. The rollers serve a dual function: they remove backlash from the system, and they transmit torque when the gears are not fully engaged.

  19. Performance of a tapered pulse tube

    SciTech Connect

    Swift, G.; Allen, M.; Woolan, J.J.

    1998-02-01

    In a well instrumented pulse tube refrigerator having 1,500 W of cooling power at 125 K, the authors have measured the figure of merit of a tapered pulse tube at several operating points. At operating points near the operating point for which the taper was designed, the figure of merit is 0.96. This is close to the theoretical optimum figure of merit 0.97 calculated for this pulse tube considering only two loss mechanisms: heat conduction in the metal pulse tube wall and ordinary thermoacoustic heat transport in the gas within a few thermal penetration depths of the wall. At operating points farther from the design operating point, the measured figure of merit is much lower, as streaming driven convection adds a third loss mechanism.

  20. Spatially resolved spectroscopy using tapered stripline NMR

    NASA Astrophysics Data System (ADS)

    Tijssen, Koen C. H.; Bart, Jacob; Tiggelaar, Roald M.; Janssen, J. W. G. (Hans); Kentgens, Arno P. M.; van Bentum, P. Jan M.

    2016-02-01

    Magnetic field B0 gradients are essential in modern Nuclear Magnetic Resonance spectroscopy and imaging. Although RF/B1 gradients can be used to fulfill a similar role, this is not used in common practice because of practical limitations in the design of B1 gradient coils. Here we present a new method to create B1 gradients using stripline RF coils. The conductor-width of a stripline NMR chip and the strength of its radiofrequency field are correlated, so a stripline chip can be tapered to produce any arbitrary shaped B1 field gradient. Here we show the characterization of this tapered stripline configuration and demonstrate three applications: magnetic resonance imaging on samples with nL-μL volumes, reaction monitoring of fast chemical reactions (10-2-101 s) and the compensation of B0 field gradients to obtain high-resolution spectra in inhomogeneous magnetic fields.

  1. Orthogonal feeding techniques for tapered slot antennas

    NASA Technical Reports Server (NTRS)

    Lee, Richard Q.; Simons, Rainee N.

    1998-01-01

    For array of "brick" configuration there are electrical and mechanical advantages to feed the antenna with a feed on a substrate perpendicular to the antenna substrate. Different techniques have been proposed for exciting patch antennas using such a feed structure.Rncently, an aperture-coupled dielectric resonator antenna using a perpendicular feed substrate has been demonstrated to have very good power coupling efficiency. For a two-dimensional rectangular array with tapered slot antenna elements, a power combining network on perpendicular substrate is generally required to couple power to or from the array. In this paper, we will describe two aperture-coupled techniques for coupling microwave power from a linearly tapered slot antenna (LTSA) to a microstrip feed on a perpendicular substrate. In addition, we will present measured results for return losses and radiation patterns.

  2. Cooling arrangement for a tapered turbine blade

    DOEpatents

    Liang, George

    2010-07-27

    A cooling arrangement (11) for a highly tapered gas turbine blade (10). The cooling arrangement (11) includes a pair of parallel triple-pass serpentine cooling circuits (80,82) formed in an inner radial portion (50) of the blade, and a respective pair of single radial channel cooling circuits (84,86) formed in an outer radial portion (52) of the blade (10), with each single radial channel receiving the cooling fluid discharged from a respective one of the triple-pass serpentine cooling circuit. The cooling arrangement advantageously provides a higher degree of cooling to the most highly stressed radially inner portion of the blade, while providing a lower degree of cooling to the less highly stressed radially outer portion of the blade. The cooling arrangement can be implemented with known casting techniques, thereby facilitating its use on highly tapered, highly twisted Row 4 industrial gas turbine blades that could not be cooled with prior art cooling arrangements.

  3. Nanostructured tapered optical fibers for paticle trapping

    NASA Astrophysics Data System (ADS)

    Daly, Mark; Truong, Viet Giang; Nic Chormaic, Síle

    2015-05-01

    Optical micro- and nanofibers have recently gained popularity as tools in quantum engineering using laser-cooled, neutral atoms. In particular, atoms can be trapped around such optical fibers, and photons coupled into the fibers from the surrounding atoms could be used to transfer quantum state information within the system. It has also been demonstrated that such fibers can be used to manipulate and trap silica and polystyrene particles in the 1-3 μm range. We recently proposed using a focused ion beam nanostructured tapered optical fiber for improved atom trapping geometries1. Here, we present details on the design and fabrication of these nanostructured optical fibers and their integration into particle trapping platforms for the demonstration of submicron particle trapping. The optical fibers are tapered to approximately 1-2 μm waist diameters, using a custom-built, heat-and-pull fiber rig, prior to processing using a focused ion beam. Slots of about 300 nm in width and 10-20 μm in length are milled right though the waist regions of the tapered optical fibers. Details on the fabrication steeps necessary to ensure high optical transmission though the fiber post processing are included. Fiber transmissions of over 80% over a broad range of wavelengths, in the 700-11100 nm range, are attainable. We also present simulation results on the impact of varying the slot parameters on the trap depths achievable and milling multiple traps within a single tapered fiber. This work demonstrates even further the functionality of optical micro- and nanofibers as trapping devices across a range of regimes.

  4. Tapered pulse tube for pulse tube refrigerators

    DOEpatents

    Swift, Gregory W.; Olson, Jeffrey R.

    1999-01-01

    Thermal insulation of the pulse tube in a pulse-tube refrigerator is maintained by optimally varying the radius of the pulse tube to suppress convective heat loss from mass flux streaming in the pulse tube. A simple cone with an optimum taper angle will often provide sufficient improvement. Alternatively, the pulse tube radius r as a function of axial position x can be shaped with r(x) such that streaming is optimally suppressed at each x.

  5. 26. Elevator no. 2: floor 4, rollers for south conveyor ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    26. Elevator no. 2: floor 4, rollers for south conveyor belt, showing top openings of grain bins on floor, with bin number on ceiling above, facing east - Washburn Crosby Company Elevators No. 2 & 3, 900 & 1000 Second Avenue, South, Minneapolis, Hennepin County, MN

  6. 24. Elevator no. 2: floor 4, turnhead distributor and rollers ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    24. Elevator no. 2: floor 4, turnhead distributor and rollers for south conveyor belt; east and south walls of control room (floor 5) in background; facing northeast - Washburn Crosby Company Elevators No. 2 & 3, 900 & 1000 Second Avenue, South, Minneapolis, Hennepin County, MN

  7. New seed-cotton reclaimer for high speed roller gins

    Technology Transfer Automated Retrieval System (TEKTRAN)

    An experimental laboratory prototype reclaimer is being developed by the USDA-ARS in cooperation with Lummus Corporation. The objective of the project is to develop a seed-cotton reclaimer for high speed roller ginning that has a higher operational capacity and reduced seed loss in comparison to cur...

  8. View of east side with large sliding door, rollers, and ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of east side with large sliding door, rollers, and tracks to large x-ray room - U.S. Naval Base, Pearl Harbor, Industrial X-Ray Building, Off Sixth Street, adjacent to and south of Facility No. 11, Pearl City, Honolulu County, HI

  9. 16. Detail showing roller nest between granite pier cap and ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    16. Detail showing roller nest between granite pier cap and moveable end of truss at east end of main spans. View to southeast. - Selby Avenue Bridge, Spanning Short Line Railways track at Selby Avenue between Hamline & Snelling Avenues, Saint Paul, Ramsey County, MN

  10. The Physics of the Roller Coaster: Learning Physics through Simulation.

    ERIC Educational Resources Information Center

    Hannum, Wallace

    2001-01-01

    This instructional design blends a structured learning environment (the physics lesson) with an engaging, playful, simulated environment (roller coaster construction), putting into operation ideas from both cognitive and constructivist theories. Two instructional models are used: a general design model for creating instruction and a lesson design…

  11. 9. VIEW OF MOLTEN SALT BATH EQUIPMENT AND ROLLER PRESSES ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    9. VIEW OF MOLTEN SALT BATH EQUIPMENT AND ROLLER PRESSES BEING INSTALLED ON THE WEST SIDE (SIDE B) OF BUILDING 883. SIDE B OF BUILDING 883 WAS USED TO PROCESS ENRICHED URANIUM FROM 1957-66. (1/23/57) - Rocky Flats Plant, Uranium Rolling & Forming Operations, Southeast section of plant, southeast quadrant of intersection of Central Avenue & Eighth Street, Golden, Jefferson County, CO

  12. Rotary roller mandrel of no. 2 seamless line in bays ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Rotary roller mandrel of no. 2 seamless line in bays 19 and 20 of the main pipe mill building looking south. - U.S. Steel National Tube Works, Main Pipe Mill Building, Along Monongahela River, McKeesport, Allegheny County, PA

  13. Bead Roller, at right, used for preparing flume sheeting (still ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Bead Roller, at right, used for preparing flume sheeting (still in use, 2004); on left is a pipe cutter. Facing southeast - Childs-Irving Hydroelectric Project, Childs System, Childs Powerhouse, Forest Service Road 708/502, Camp Verde, Yavapai County, AZ

  14. Finite-aperture tapered unstable resonator lasers

    NASA Astrophysics Data System (ADS)

    Bedford, Robert George

    The development of high power, high brightness semiconductor lasers is important for applications such as efficient pumping of fiber amplifiers and free space communication. The ability to couple directly into the core of a single-mode fiber can vastly increase the absorption of pump light. Further, the high mode-selectivity provided by unstable resonators accommodates single-mode operation to many times the threshold current level. The objective of this dissertation is to investigate a more efficient semiconductor-based unstable resonator design. The tapered unstable resonator laser consists of a single-mode ridge coupled to a tapered gain region. The ridge, aided by spoiling grooves, provides essential preparation of the fundamental mode, while the taper provides significant amplification and a large output mode. It is shown a laterally finite taper-side mirror (making the laser a "finite-aperture tapered unstable resonator laser") serves to significantly improve differential quantum efficiency. This results in the possibility for higher optical powers while still maintaining single-mode operation. Additionally, the advent of a detuned second order grating allows for a low divergent, quasicircular output beam emitted from the semiconductor surface, easing packaging tolerances, and making two dimensional integrated arrays possible. In this dissertation, theory, design, fabrication, and characterization are presented. Material theory is introduced, reviewing gain, carrier, and temperature effects on field propagation. Coupled-mode and coupled wave theory is reviewed to allow simulation of the passive grating. A numerical model is used to investigate laser design and optimization, and effects of finite-apertures are explored. A microfabrication method is introduced to create the FATURL in InAlGaAs/-InGaAsP/InP material emitting at about 1410 nm. Fabrication consists of photolithography, electron-beam lithography, wet etch and dry etching processes, metal and

  15. Measurement of transferable chemical residue from nylon carpet using the California roller and a new mega-California roller.

    PubMed

    Williams, Ryan L; Bernard, Craig E; Dyk, Melinda Bigelow; Ross, John H; Krieger, Robert I

    2008-11-01

    Human chemical exposures resulting from transfer of surface deposition on indoor nylon carpets may be estimated by measuring transferable residues (mu g chemical/cm2 carpet). A weighted roller developed at California Department of Food and Agriculture (CDFA) has been extensively used to sample transferable residue for estimates of human exposure in risk characterization. A modified roller has been developed to evaluate the influence of pressure on transferable chemical residue since weight and force (or pressure, kg/m2) may vary person-to-person and activity-to-activity. A 30.5 cm diameter roller was used to apply 60 to 2100 kg/m2 to bracket pressures exerted by humans on a flat nylon-carpeted surface. Measurements of transferable cyfluthrin residues were made after 1, 7, and 21 days. Total Soxhlet extractable cyfluthrin residues were relatively constant during the test period. Residue transferability decreased during the study period. Modest increases in the transferability of surface residues were observed over the broad range of pressures applied by the modified roller.

  16. Trapping light into high orbital momentum modes of fiber tapers.

    PubMed

    Strekalov, Dmitry V; Savchenkov, Anatoliy A; Savchenkova, Ekaterina A; Matsko, Andrey B

    2015-08-15

    A tapered cylindrical dielectric optical waveguide acts as a high quality factor white-light cavity providing high field concentration as well as long optical group delay. It is possible to optimize shape of a lossless taper to suppress reflection of the input light and to achieve infinitely high field concentration. These tapers can be used in sensing and optoelectronics applications instead of conventional microcavities. PMID:26274659

  17. Welding-fume-induced transmission loss in tapered optical fibers

    NASA Astrophysics Data System (ADS)

    Yi, Ji-Haeng

    2015-09-01

    This paper presents a method for sensing welding fumes in real time. This method is based on the results of nanoparticle-induced optical-fiber loss experiments that show that the losses are determined by the nanoparticle density and the taper waist. The tapered fiber is obtained by applying heat radiated from hot quartz, and monitoring is done in real time. First, the durability of the tapered fiber during the welding process is proven. Then, the loss is categorized by using the sizes of welding fume particles. The sensitivity to welding fumes increases with increasing size of the particles; consequently, the dimension of the taper waist decreases.

  18. Monitoring techniques for the manufacture of tapered optical fibers.

    PubMed

    Mullaney, Kevin; Correia, Ricardo; Staines, Stephen E; James, Stephen W; Tatam, Ralph P

    2015-10-01

    The use of a range of optical techniques to monitor the process of fabricating optical fiber tapers is investigated. Thermal imaging was used to optimize the alignment of the optical system; the transmission spectrum of the fiber was monitored to confirm that the tapers had the required optical properties and the strain induced in the fiber during tapering was monitored using in-line optical fiber Bragg gratings. Tapers were fabricated with diameters down to 5 μm and with waist lengths of 20 mm using single-mode SMF-28 fiber. PMID:26479631

  19. An acoustic vibration sensor based on tapered triple cladding fiber

    NASA Astrophysics Data System (ADS)

    Xu, Hui; Pang, Fufei; Zhao, Shiqi; Chen, Zhenyi; Wang, Tingyun

    2014-05-01

    An acoustic vibration sensor is investigated and demonstrated by using a tapered triple cladding fiber (TCF). It is fabricated by tapering a length of 2 cm TCF which is spliced between two single mode fibers (SMF). The TCF consists of core, inner cladding, middle cladding and outer cladding. After the tapering process, this structure becomes a tapered coaxial fiber coupler which presents a periodic filtering transmission spectrum. The surrounding vibration perturbation can be directly demodulated by intensity detection of the transmission power at a particular wavelength. The experimental result shows that the maximum frequency response of 700 kHz is achieved.

  20. Low-crosstalk Si arrayed waveguide grating with parabolic tapers.

    PubMed

    Ye, Tong; Fu, Yunfei; Qiao, Lei; Chu, Tao

    2014-12-29

    A silicon arrayed waveguide grating (AWG) with low channel crosstalk was demonstrated by using ultra-short parabolic tapers to connect the AWG's free propagation regions and single-mode waveguides. The tapers satisfied the requirements of low-loss mode conversion and lower channel crosstalk from the coupling of neighboring waveguides in the AWGs. In this work, three different tapers, including parabolic tapers, linear tapers, and exponential tapers, were theoretically analyzed and experimentally investigated for a comparison of their effects when implemented in AWGs. The experimental results showed that the AWG with parabolic tapers had a crosstalk improvement up to 7.1 dB compared with the others. Based on the advantages of parabolic tapers, a 400-GHz 8 × 8 cyclic AWG with 2.4 dB on-chip loss and -17.6~-25.1 dB crosstalk was fabricated using a simple one-step etching process. Its performance was comparable with that of existing AWGs with bi-level tapers, which require complicated two-step etching fabrication processes.

  1. Measurement of Liquid Viscosities in Tapered or Parabolic Capillaries.

    PubMed

    Ershov; Zorin; Starov

    1999-08-01

    The possibility of using tapered or parabolic capillaries for measurement of liquid viscosities is investigated both experimentally and theoretically. It is demonstrated that even small deviations in capillary radius from a constant value may substantially affect measurement results. Equations are derived which allow correct analysis of the measurement results in tapered or parabolic capillaries. The following cases are analyzed: a water imbibition into a tapered or parabolic capillary and displacement of one liquid by another immiscible liquid in tapered or parabolic capillaries. Two possibilities are considered: (a) the narrow end of the capillary as capillary inlet and (b) the wide end of the capillary as capillary inlet. Copyright 1999 Academic Press.

  2. Radiation pattern analysis of the tapered slot antenna, appendix 1

    NASA Technical Reports Server (NTRS)

    Janaswamy, Ramakrishna

    1986-01-01

    A theoretical model for the tapered slot antenna is presented. The model is valid for any smooth taper of the slot. The problem is solved by modeling the slot electric field and using the half plane Green's function to compute the far fields. The aperture field is obtained by affecting a stepped approximation to the continuous taper and utilizing the uniform wide slot line data. The uniform wide slot line is solved by the spectral Galerkin's technique and closed form experssions are developed for the slot wave length and the slot characteristic impedance. Numerous comparisons with measurement are made to demonstrate the versatility of the model in treating an arbitrary slot taper.

  3. Study of rolling element dynamic interactions with separators and raceway paths: Roller to separator contact forces and cage to shaft speed ratios in roller bearings

    NASA Technical Reports Server (NTRS)

    Nypan, L. J.

    1978-01-01

    Cage to roller force measurements, cage to shaft forces, and cage to shaft speed ratios are reported for 115 and 118mm bore roller bearings operating at speeds of 4,000, 8,000, and 12,000 rpm under loads ranging from 360 to 6670 N (80 to 1500 lb).

  4. Window taper functions for subaperture processing.

    SciTech Connect

    Doerry, Armin Walter

    2013-12-01

    It is well known that the spectrum of a signal can be calculated with a Discrete Fourier Transform (DFT), where best resolution is achieved by processing the entire data set. However, in some situations it is advantageous to use a staged approach, where data is first processed within subapertures, and the results are then combined and further processed to a final result. An artifact of this approach is the creation of grating lobes in the final response. The nature of the grating lobes, including their amplitude and spacing, is an artifact of window taper functions, subaperture offsets, and subaperture processing parameters. We assess these factors and exemplify their effects.

  5. Improved Tennis Racquets Have Tapered Strings

    NASA Technical Reports Server (NTRS)

    Noever, David A.

    1995-01-01

    Design concept for better performing tennis racquet. Essence of concept to taper strings in such way as to shift center of percussion (also called "sweet spot") toward the toe (outer end of racquet, farthest from player's hand). In addition to increasing power on serves, also improves player's control and feel of racquet in player's hand. Racquet less likely to twist in player's hand on off-center shots. Important element of better feel is better absorption of vibrations; especially for players having chronic arm problems. String material nylon, animal gut, or other naturally or artifically spun threads. String can be attached to conventional racquet frame.

  6. A scaled roller test rig for high-speed vehicles

    NASA Astrophysics Data System (ADS)

    Allotta, Benedetto; Pugi, Luca; Malvezzi, Monica; Bartolini, Fabio; Cangioli, Francesco

    2010-12-01

    Scaled roller rigs are quite widespread among railway research centres, and several examples are described in the literature. Due to their low costs and ease of use compared with full-scale counterparts, these types of rigs are used for a wide range of studies concerning dynamical stability, comfort, mechatronic subsystem and wear. Furthermore, scaled roller rigs can be a powerful education tool for railway engineering students. In this paper, the design and the main features of the scaled rolled rig that will be installed in the Mechatronics and Dynamic Modeling Laboratory of the University of Florence located in Pistoia, Italy, are described. The main feature of the proposed rig will be the simulation of degraded adhesion conditions. This feature is very important for hardware-in-the loop testing of many safety relevant on-board subsystems like wheel slide protection systems, traction and stability controls, odometry and automatic train protection and control.

  7. Student investigations of the forces in a roller coaster loop

    NASA Astrophysics Data System (ADS)

    Pendrill, Ann-Marie

    2013-11-01

    How does the experience of a riding in a roller coaster loop depend on your position in the train? This question has been investigated by first year engineering physics students by using multiple representations of force and motion. Theoretical considerations for a circular loop show that the differences between the forces on a rider in the front, middle or back of the train depend on the ratio between train length and radius of the loop, which can be estimated from a photograph. Numerical computations complement the analysis of a video clip, accelerometer data, and measurements of the time needed for the train to move over the highest point. A roller coaster ride gives striking examples of Newton's laws applied to your own body, and demonstrates that the experience depends on the vector character of velocity and acceleration.

  8. Flow and roller array interaction at low Reynolds numbers

    NASA Astrophysics Data System (ADS)

    Sheikh, Zubair M.; Wang, Lipo; Zhang, Qiang

    2016-06-01

    Differing from the conventional no-slip wall boundary condition, the moving surface may have strong influences on the flow structures and the flow physics. Such effects are potentially important and useful for flow control. In this paper we analyze the two-dimensional flow over a roller array with different spacing and rotating speeds at the low Reynolds numbers. The numerical results indicate that the pressure drag and the friction drag of the rollers are strongly dependent on flowing and geometric parameters. Physically, surface motion can induce the viscous traction stream, which leads to very important effects, such as the so called impingement block and traction stream flush. These interesting findings may help to better understand the fluid dynamics for the general moving boundary cases.

  9. Pin and roller attachment system for ceramic blades

    DOEpatents

    Shaffer, J.E.

    1995-07-25

    In a turbine, a plurality of blades are attached to a turbine wheel by way of a plurality of joints which form a rolling contact between the blades and the turbine wheel. Each joint includes a pin and a pair of rollers to provide rolling contact between the pin and an adjacent pair of blades. Because of this rolling contact, high stress scuffing between the blades and the turbine wheel reduced, thereby inhibiting catastrophic failure of the blade joints. 3 figs.

  10. Pin and roller attachment system for ceramic blades

    DOEpatents

    Shaffer, James E.

    1995-01-01

    In a turbine, a plurality of blades are attached to a turbine wheel by way of a plurality of joints which form a rolling contact between the blades and the turbine wheel. Each joint includes a pin and a pair of rollers to provide rolling contact between the pin and an adjacent pair of blades. Because of this rolling contact, high stress scuffing between the blades and the turbine wheel reduced, thereby inhibiting catastrophic failure of the blade joints.

  11. Interference-Fit Life Factors for Roller Bearings

    NASA Technical Reports Server (NTRS)

    Oswald, Fred B.; Zaretsky, Erwin V.; Poplawski, Joseph V.

    2009-01-01

    The effect of hoop stresses in reducing cylindrical roller bearing fatigue life was determined for various classes of inner-ring interference fit. Calculations were performed for up to 7 fit classes for each of 10 bearing sizes. The hoop stresses were superimposed on the Hertzian principal stresses created by the applied radial load to calculate roller bearing fatigue life. A method was developed through a series of equations to calculate the life reduction for cylindrical roller bearings. All calculated lives are for zero initial internal clearance. Any reduction in bearing clearance due to interference fit would be compensated by increasing the initial (unmounted) clearance. Results are presented as tables and charts of life factors for bearings with light, moderate, and heavy loads and interference fits ranging from extremely light to extremely heavy for bearing accuracy class RBEC-5 (ISO class 5). Interference fits on the inner ring of a cylindrical roller bearing can significantly reduce bearing fatigue life. In general, life factors are smaller (lower life) for bearings running under light load where the unfactored life is highest. The various bearing series within a particular bore size had almost identical interference-fit life factors for a particular fit. The tightest fit at the high end of the tolerance band produces a life factor of approximately 0.40 for an inner-race maximum Hertz stress of 1200 MPa (175 ksi) and a life factor of 0.60 for an inner-race maximum Hertz stress of 2200 MPa (320 ksi). Interference fits also impact the maximum Hertz stress-life relation.

  12. Salmonella transfer during pilot plant scale washing and roller conveying of tomatoes.

    PubMed

    Wang, Haiqiang; Ryser, Elliot T

    2014-03-01

    Salmonella transfer during washing and roller conveying of inoculated tomatoes was quantified using a pilot scale tomato packing line equipped with plastic, foam, or brush rollers. Red round tomatoes (2.3 kg) were dip inoculated with Salmonella enterica serovar Typhimurium LT2 (avirulent) (4 log CFU/g), air dried for 2 h, and then washed in sanitizer-free water for 2 min. Inoculated tomatoes were then passed single file over a 1.5-m conveyor equipped with plastic, foam, or brush rollers followed by 25 previously washed uninoculated tomatoes. Tomato samples were collected after 2 min of both washing and roller conveying, with all 25 uninoculated tomatoes collected individually after conveying. Roller surface samples were collected before and after conveying the uninoculated tomatoes. Both tomato and surface samples were quantitatively examined for Salmonella by direct plating or membrane filtration using xylose lysine Tergitol 4 agar. Regardless of the roller type, Salmonella populations on inoculated tomatoes did not significantly (P < 0.05) decrease during contact with the roller conveyors. After conveying uninoculated tomatoes over contaminated foam rollers, 96% of the 25 tomatoes were cross-contaminated with Salmonella at >100 CFU per tomato. With plastic rollers, 24 and 76% of tomatoes were cross-contaminated with Salmonella at 10 to 100 and 1 to 10 CFU per tomato, respectively. In contrast, only 8% of 25 tomatoes were cross-contaminated with brush rollers with Salmonella populations of 1 to 10 CFU per tomato. Overall, cross-contamination was greatest with foam, followed by plastic and brush rollers (P < 0.05). Adding peroxyacetic acid or chlorine to the wash water significantly decreased cross-contamination during tomato conveying, with chlorine less effective in controlling Salmonella on foam compared with plastic and brush rollers. PMID:24674428

  13. Salmonella transfer during pilot plant scale washing and roller conveying of tomatoes.

    PubMed

    Wang, Haiqiang; Ryser, Elliot T

    2014-03-01

    Salmonella transfer during washing and roller conveying of inoculated tomatoes was quantified using a pilot scale tomato packing line equipped with plastic, foam, or brush rollers. Red round tomatoes (2.3 kg) were dip inoculated with Salmonella enterica serovar Typhimurium LT2 (avirulent) (4 log CFU/g), air dried for 2 h, and then washed in sanitizer-free water for 2 min. Inoculated tomatoes were then passed single file over a 1.5-m conveyor equipped with plastic, foam, or brush rollers followed by 25 previously washed uninoculated tomatoes. Tomato samples were collected after 2 min of both washing and roller conveying, with all 25 uninoculated tomatoes collected individually after conveying. Roller surface samples were collected before and after conveying the uninoculated tomatoes. Both tomato and surface samples were quantitatively examined for Salmonella by direct plating or membrane filtration using xylose lysine Tergitol 4 agar. Regardless of the roller type, Salmonella populations on inoculated tomatoes did not significantly (P < 0.05) decrease during contact with the roller conveyors. After conveying uninoculated tomatoes over contaminated foam rollers, 96% of the 25 tomatoes were cross-contaminated with Salmonella at >100 CFU per tomato. With plastic rollers, 24 and 76% of tomatoes were cross-contaminated with Salmonella at 10 to 100 and 1 to 10 CFU per tomato, respectively. In contrast, only 8% of 25 tomatoes were cross-contaminated with brush rollers with Salmonella populations of 1 to 10 CFU per tomato. Overall, cross-contamination was greatest with foam, followed by plastic and brush rollers (P < 0.05). Adding peroxyacetic acid or chlorine to the wash water significantly decreased cross-contamination during tomato conveying, with chlorine less effective in controlling Salmonella on foam compared with plastic and brush rollers.

  14. 5 CFR 353.303 - Restoration rights of TAPER employees.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 5 Administrative Personnel 1 2011-01-01 2011-01-01 false Restoration rights of TAPER employees... REGULATIONS RESTORATION TO DUTY FROM UNIFORMED SERVICE OR COMPENSABLE INJURY Compensable Injury § 353.303 Restoration rights of TAPER employees. An employee serving in the competitive service under a...

  15. 5 CFR 353.303 - Restoration rights of TAPER employees.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Restoration rights of TAPER employees... REGULATIONS RESTORATION TO DUTY FROM UNIFORMED SERVICE OR COMPENSABLE INJURY Compensable Injury § 353.303 Restoration rights of TAPER employees. An employee serving in the competitive service under a...

  16. The violin bow: taper, camber and flexibility.

    PubMed

    Gough, Colin

    2011-12-01

    An analytic, small-deflection, simplified model of the modern violin bow is introduced to describe the bending profiles and related strengths of an initially straight, uniform cross-section, stick as a function of bow hair tension. A number of illustrative bending profiles (cambers) of the bow are considered, which demonstrate the strong dependence of the flexibility of the bow on longitudinal forces across the ends of the bent stick. Such forces are shown to be comparable in strength to critical buckling loads causing excessive sideways buckling unless the stick is very straight. Non-linear, large deformation, finite element computations extend the analysis to bow hair tensions comparable with and above the critical buckling strength of the straight stick. The geometric model assumes an expression for the taper of Tourte bows introduced by Vuillaume, which is re-examined and generalized to describe violin, viola and cello bows. A comparison is made with recently published measurements of the taper and bending profiles of a particularly fine bow by Kittel. PMID:22225065

  17. The violin bow: taper, camber and flexibility.

    PubMed

    Gough, Colin

    2011-12-01

    An analytic, small-deflection, simplified model of the modern violin bow is introduced to describe the bending profiles and related strengths of an initially straight, uniform cross-section, stick as a function of bow hair tension. A number of illustrative bending profiles (cambers) of the bow are considered, which demonstrate the strong dependence of the flexibility of the bow on longitudinal forces across the ends of the bent stick. Such forces are shown to be comparable in strength to critical buckling loads causing excessive sideways buckling unless the stick is very straight. Non-linear, large deformation, finite element computations extend the analysis to bow hair tensions comparable with and above the critical buckling strength of the straight stick. The geometric model assumes an expression for the taper of Tourte bows introduced by Vuillaume, which is re-examined and generalized to describe violin, viola and cello bows. A comparison is made with recently published measurements of the taper and bending profiles of a particularly fine bow by Kittel.

  18. Electromagnetic field tapering using all-dielectric gradient index materials

    NASA Astrophysics Data System (ADS)

    Yi, Jianjia; Piau, Gérard-Pascal; de Lustrac, André; Burokur, Shah Nawaz

    2016-07-01

    The concept of transformation optics (TO) is applied to control the flow of electromagnetic fields between two sections of different dimensions through a tapering device. The broadband performance of the field taper is numerically and experimentally validated. The taper device presents a graded permittivity profile and is fabricated through three-dimensional (3D) polyjet printing technology using low-cost all-dielectric materials. Calculated and measured near-field mappings are presented in order to validate the proposed taper. A good qualitative agreement is obtained between full-wave simulations and experimental tests. Such all-dielectric taper paves the way to novel types of microwave devices that can be easily fabricated through low-cost additive manufacturing processes.

  19. Electromagnetic field tapering using all-dielectric gradient index materials

    PubMed Central

    Yi, Jianjia; Piau, Gérard-Pascal; de Lustrac, André; Burokur, Shah Nawaz

    2016-01-01

    The concept of transformation optics (TO) is applied to control the flow of electromagnetic fields between two sections of different dimensions through a tapering device. The broadband performance of the field taper is numerically and experimentally validated. The taper device presents a graded permittivity profile and is fabricated through three-dimensional (3D) polyjet printing technology using low-cost all-dielectric materials. Calculated and measured near-field mappings are presented in order to validate the proposed taper. A good qualitative agreement is obtained between full-wave simulations and experimental tests. Such all-dielectric taper paves the way to novel types of microwave devices that can be easily fabricated through low-cost additive manufacturing processes. PMID:27464989

  20. Sensitive acoustic vibration sensor using single-mode fiber tapers.

    PubMed

    Li, Yi; Wang, Xiaozhen; Bao, Xiaoyi

    2011-05-01

    Optical fiber sensors are a good alternative to piezoelectric devices in electromagnetic sensitive environments. In this study, we reported a fiber acoustic sensor based on single-mode fiber (SMF) tapers. The fiber taper is used as the sensing arm in a Mach-Zehnder interferometer. Benefiting from their micrometer dimensions, fiber tapers have shown higher sensitivities to the acoustic vibrations than SMFs. Under the same conditions, the thinnest fiber taper in this report, with a diameter of 1.7 µm, shows a 20 dB improvement in the signal to noise ratio as compared to that of an SMF. This acoustic vibration sensor can detect the acoustic waves over the frequencies of 30 Hz-40 kHz, which is limited by the acoustic wave generator in experiments. We also discussed the phase changes of fiber tapers with different diameters under acoustic vibrations.

  1. Electromagnetic field tapering using all-dielectric gradient index materials.

    PubMed

    Yi, Jianjia; Piau, Gérard-Pascal; de Lustrac, André; Burokur, Shah Nawaz

    2016-01-01

    The concept of transformation optics (TO) is applied to control the flow of electromagnetic fields between two sections of different dimensions through a tapering device. The broadband performance of the field taper is numerically and experimentally validated. The taper device presents a graded permittivity profile and is fabricated through three-dimensional (3D) polyjet printing technology using low-cost all-dielectric materials. Calculated and measured near-field mappings are presented in order to validate the proposed taper. A good qualitative agreement is obtained between full-wave simulations and experimental tests. Such all-dielectric taper paves the way to novel types of microwave devices that can be easily fabricated through low-cost additive manufacturing processes. PMID:27464989

  2. Functional significance of the taper of vertebrate cone photoreceptors

    PubMed Central

    Hárosi, Ferenc I.

    2012-01-01

    Vertebrate photoreceptors are commonly distinguished based on the shape of their outer segments: those of cones taper, whereas the ones from rods do not. The functional advantages of cone taper, a common occurrence in vertebrate retinas, remain elusive. In this study, we investigate this topic using theoretical analyses aimed at revealing structure–function relationships in photoreceptors. Geometrical optics combined with spectrophotometric and morphological data are used to support the analyses and to test predictions. Three functions are considered for correlations between taper and functionality. The first function proposes that outer segment taper serves to compensate for self-screening of the visual pigment contained within. The second function links outer segment taper to compensation for a signal-to-noise ratio decline along the longitudinal dimension. Both functions are supported by the data: real cones taper more than required for these compensatory roles. The third function relates outer segment taper to the optical properties of the inner compartment whereby the primary determinant is the inner segment’s ability to concentrate light via its ellipsoid. In support of this idea, the rod/cone ratios of primarily diurnal animals are predicted based on a principle of equal light flux gathering between photoreceptors. In addition, ellipsoid concentration factor, a measure of ellipsoid ability to concentrate light onto the outer segment, correlates positively with outer segment taper expressed as a ratio of characteristic lengths, where critical taper is the yardstick. Depending on a light-funneling property and the presence of focusing organelles such as oil droplets, cone outer segments can be reduced in size to various degrees. We conclude that outer segment taper is but one component of a miniaturization process that reduces metabolic costs while improving signal detection. Compromise solutions in the various retinas and retinal regions occur between

  3. Tapering Practices of New Zealand's Elite Raw Powerlifters.

    PubMed

    Pritchard, Hayden J; Tod, David A; Barnes, Matthew J; Keogh, Justin W; McGuigan, Michael R

    2016-07-01

    Pritchard, HJ, Tod, DA, Barnes, MJ, Keogh, JW, and McGuigan, MR. Tapering practices of New Zealand's elite raw powerlifters. J Strength Cond Res 30(7): 1796-1804, 2016-The major aim of this study was to determine tapering strategies of elite powerlifters. Eleven New Zealand powerlifters (28.4 ± 7.0 years, best Wilks score of 431.9 ± 43.9 points) classified as elite were interviewed, using semistructured interviews, about their tapering strategies. Interviews were transcribed verbatim and content analyzed. Total training volume peaked 5.2 ± 1.7 weeks from competition while average training intensity (of 1 repetition maximum) peaked 1.9 ± 0.8 weeks from competition. During tapering, volume was reduced by 58.9 ± 8.4% while intensity was maintained (or slightly reduced) and the final weight training session was performed 3.7 ± 1.6 days out from competition. Participants generally stated that tapering was performed to achieve full recovery; that accessory work was removed around 2 weeks out from competition; and deadlifting takes longer to recover from than other lifts. Typically participants stated that trial and error, and changes based on "feel" were the sources of tapering strategies; equipment used and movements performed during tapering are the same as in competition; nutrition was manipulated during the taper (for weight cutting or performance aims); and poor tapering occurred when too long (1 week or more) was taken off training. These results suggest that athletes may benefit from continuing to strength train before important events with reduced volume and maintained intensity. Only exercises that directly assist sports performance should remain in the strength program during tapering, to assist with reductions in fatigue while maintaining/improving strength expression and performance.

  4. Roller compaction: Effect of relative humidity of lactose powder.

    PubMed

    Omar, Chalak S; Dhenge, Ranjit M; Palzer, Stefan; Hounslow, Michael J; Salman, Agba D

    2016-09-01

    The effect of storage at different relative humidity conditions, for various types of lactose, on roller compaction behaviour was investigated. Three types of lactose were used in this study: anhydrous lactose (SuperTab21AN), spray dried lactose (SuperTab11SD) and α-lactose monohydrate 200M. These powders differ in their amorphous contents, due to different manufacturing processes. The powders were stored in a climatic chamber at different relative humidity values ranging from 10% to 80% RH. It was found that the roller compaction behaviour and ribbon properties were different for powders conditioned to different relative humidities. The amount of fines produced, which is undesirable in roller compaction, was found to be different at different relative humidity. The minimum amount of fines produced was found to be for powders conditioned at 20-40% RH. The maximum amount of fines was produced for powders conditioned at 80% RH. This was attributed to the decrease in powder flowability, as indicated by the flow function coefficient ffc and the angle of repose. Particle Image Velocimetry (PIV) was also applied to determine the velocity of primary particles during ribbon production, and it was found that the velocity of the powder during the roller compaction decreased with powders stored at high RH. This resulted in less powder being present in the compaction zone at the edges of the rollers, which resulted in ribbons with a smaller overall width. The relative humidity for the storage of powders has shown to have minimal effect on the ribbon tensile strength at low RH conditions (10-20%). The lowest tensile strength of ribbons produced from lactose 200M and SD was for powders conditioned at 80% RH, whereas, ribbons produced from lactose 21AN at the same condition of 80% RH showed the highest tensile strength. The storage RH range 20-40% was found to be an optimum condition for roll compacting three lactose powders, as it resulted in a minimum amount of fines in the

  5. Roller compaction: Effect of relative humidity of lactose powder.

    PubMed

    Omar, Chalak S; Dhenge, Ranjit M; Palzer, Stefan; Hounslow, Michael J; Salman, Agba D

    2016-09-01

    The effect of storage at different relative humidity conditions, for various types of lactose, on roller compaction behaviour was investigated. Three types of lactose were used in this study: anhydrous lactose (SuperTab21AN), spray dried lactose (SuperTab11SD) and α-lactose monohydrate 200M. These powders differ in their amorphous contents, due to different manufacturing processes. The powders were stored in a climatic chamber at different relative humidity values ranging from 10% to 80% RH. It was found that the roller compaction behaviour and ribbon properties were different for powders conditioned to different relative humidities. The amount of fines produced, which is undesirable in roller compaction, was found to be different at different relative humidity. The minimum amount of fines produced was found to be for powders conditioned at 20-40% RH. The maximum amount of fines was produced for powders conditioned at 80% RH. This was attributed to the decrease in powder flowability, as indicated by the flow function coefficient ffc and the angle of repose. Particle Image Velocimetry (PIV) was also applied to determine the velocity of primary particles during ribbon production, and it was found that the velocity of the powder during the roller compaction decreased with powders stored at high RH. This resulted in less powder being present in the compaction zone at the edges of the rollers, which resulted in ribbons with a smaller overall width. The relative humidity for the storage of powders has shown to have minimal effect on the ribbon tensile strength at low RH conditions (10-20%). The lowest tensile strength of ribbons produced from lactose 200M and SD was for powders conditioned at 80% RH, whereas, ribbons produced from lactose 21AN at the same condition of 80% RH showed the highest tensile strength. The storage RH range 20-40% was found to be an optimum condition for roll compacting three lactose powders, as it resulted in a minimum amount of fines in the

  6. Comparison of free-electron laser amplifiers based on a step-tapered optical klystron and a conventional tapered wiggler

    NASA Astrophysics Data System (ADS)

    Freund, H. P.

    2013-06-01

    Free-electron laser amplifiers have been operated at high efficiency at wavelengths from the microwave through the visible. Typically, these amplifiers require long tapered sections and produce spent beams with large energy spreads that are 4-5 times the electronic efficiency. In addition, while optical guiding during exponential growth in the uniform wiggler section confines the optical mode, the guiding disappears in the tapered wiggler section resulting in a relatively large optical mode at the wiggler exit. Optical klystrons consist of a Modulator wiggler that induces a velocity modulation on the electron beam followed by a magnetic dispersive section that enhances the velocity modulation prior to injection into a second, radiator wiggler. Optical klystrons have been operated over a broad spectral range; however, no optical klystron has been built with a tapered radiator wiggler. A comparison between a optical klystron with a step-tapered Radiator wiggler and a conventional tapered wiggler amplifier is analyzed in this paper. The purpose of the step taper is to both enhance the efficiency and to extend the range of the exponential gain and so preserve the optical guiding over a longer interaction length. The step-tapered optical klystron and a tapered wiggler amplifier are compared for a nominal set of parameters to determine the differences in the efficiency, interaction length, spent beam energy spread, and the size of the optical mode at the wiggler exit.

  7. Mach-Zehnder interferometer based on tapered PCF with an up-tapered joint for curvature, strain and temperature interrogation

    NASA Astrophysics Data System (ADS)

    Narayan Dash, Jitendra; Jha, Rajan

    2016-10-01

    We propose a Mach-Zehnder interferometric sensor based on tapered Photonic Crystal Fiber (PCF) with up-tapered collapsed region for measurement of parameters such as curvature, strain and temperature. The up-tapered collapsed region helps in excitation of the cladding modes in PCF and these modes interfere with each other at the tapered region of PCF which is completely collapsed. Three tapered PCFs with varying geometry are fabricated and their effect on curvature sensitivity is analyzed. Experimental results show that the proposed sensor has a curvature sensitivity of 7.56 nm m-1 with negligible hysteresis effect. Moreover, the proposed sensor shows a strain sensitivity of 1.6 pm/μɛ along with a maximum temperature sensitivity of 51.6 pm °C-1. In addition to this, the response of the interference pattern to all these parameters is found to be linear.

  8. Design of Structurally Efficient Tapered Struts (SETS)

    NASA Technical Reports Server (NTRS)

    Deo, Ravi; Benner, Harry; Vincent, Dawson; Olason, Eric; Harrison, Richard

    2010-01-01

    A study was conducted to develop mass efficient composite struts. A closed-form design methodology for composite struts was developed using well established analyses to predict Euler buckling, local wall buckling; compression strength, damage tolerance, and interlaminar shear at geometric gradients. The methodology was coded in a spreadsheet suitable for convenient and rapid sizing of tapered composite struts. This spreadsheet analysis was used to determine the influence of several variables such as material stiffness, strut diameter, and material allowables on strut weight for given loading conditions. The comparison showed that, while the Park Aerospace design method was well suited to preliminary sizing for a conservative design, the closed-form-analyses-based spreadsheet accounts for all possible failure modes and is a good optimum strut design tool. The report concludes with a set of recommendations for future work in analytical design and analysis methodology enhancements.

  9. Columnar structures from asymmetrically tapered biphenylamide.

    PubMed

    Park, Soo-Jin; Hwang, Seok-Ho; Kim, Namil; Kuo, Shiao-Wei; Kim, Hak Yong; Park, Seul-Ki; Kim, Young-Jin; Nah, Changwoon; Lee, Joong Hee; Jeong, Kwang-Un

    2009-10-15

    An asymmetrically tapered N,N'-tris[[(2-dodecylaminocarbonyl)ethyl]methyl]-4-biphenylamide (asym-C(12)PhA, where n is the number of carbon atoms in the alkyl chains, n = 12) was newly designed and synthesized. In this asymmetrically tapered asym-C(12)PhA biphenylamide, H-bondable hydrophilic amide moieties are located at between a rigid hydrophobic biphenyl rod and three flexible hydrophobic alkyl chains. Computer energy minimization indicated that three-dimensional (3D) geometry of asym-C(12)PhA biphenylamide looks like a cone with dimensions of 3.01 nm in height and 1.44 nm in bottom radius. Phase transitions and supra-molecular structures were identified utilizing the combined techniques of differential scanning calorimetry, 1D wide-angle X-ray diffraction (1D WAXD), Fourier-transform infrared spectroscopy, and solid-state (13)C nuclear magnetic resonance analyses. The asym-C(12)PhA self-assembled into a highly ordered columnar mesophase just below the isotropization temperature and then transformed to 3D columnar crystalline phase (Phi(Cr)) on further cooling. Selected area electron diffractions in transmission electron microscopy (TEM) along with 1D WAXD and cross-polarized optical microscopy suggested that discotic building blocks were constructed by rotating 120 degrees of three asym-C(12)PhA with respect to neighboring ones and the tmb (top-middle-bottom) stacked discotic building blocks further self-organized into columns. These columns are laterally intercalated to form the Phi(Cr) phase. On the basis of the TEM image and polyethylene surface decoration technology, it was identified that the self-assembled asym-C(12)PhA fibers with approximately 1 mum in diameter and several millimeters in length were braids of tiny single crystals.

  10. Discontinuous Tapered Surface Plasmon Polariton Waveguides with Gap.

    PubMed

    Lee, Dong Hun; Lee, Myung-Hyun

    2016-06-01

    We investigate characteristics of discontinuous tapered surface plasmon polariton waveguides with a gap (DTG-SPPWs) to control a guided surface plasmon polariton (SPP) at a telecommunication wavelength of 1.55 μm. The DTG-SPPWs are composed of an input 2 μm-wide and 10 μm-long reverse tapered IMI-W (RT-IMI-W) and a 10 μm-long tapered and output 2 μm-wide IMI-W (T-IMI-W) with the 8 μm-long gap. The width and length of the tapered regions in the RT-IMI-W and the T-IMI-W were varied from 2 to 10 μm and 1 to 8 μm, respectively. Gold is used as the metal in the insulator-metal-insulator waveguides (IMI-Ws). The thickness of the gold strips is fixed with 20 nm. A low-loss polymer is used for the 30 μm-thick upper and lower cladding layers. The coupling losses of the DTG-SPPWs are less than 0.055 dB with an 8 μm-long gap and various taper widths up to 10 μm. The normalized transmissions (NTs) of the DTG-SPPWs are less than about -0.060 dB with various taper widths up to 10 μm. The NTs of the DTG-SPPWs are less than about -0.069 dB with various taper lengths up to 8 μm. The maximum NT of about -0.042 dB was obtained using the 6 μm-wide taper width and the 3 μm-long taper length in the DTG-SPPW. The DTG-SPPWs have potential as a new plasmonic modulation device via control of the guided SPP through interaction with an applied force in the gap. PMID:27427702

  11. [The morse taper junction in modular revision hip replacement].

    PubMed

    Gravius, S; Mumme, T; Andereya, S; Maus, U; Müller-Rath, R; Wirtz, D C

    2007-01-01

    Morse taper junctions of modular hip revision replacements are predilection sites for fretting, crevice corrosion, dissociation and breakage of the components. In this report we present the results of a retrieval analysis of a morse taper junction of a MRP-titanium modular revision replacement (MRP-Titanium, Peter Brehm GmbH, Weisendorf, Germany) after 11.5 years of in vivo use. In the context of this case report the significance of morse taper junctions in modular hip revision replacement under consideration of the current literature is also discussed.

  12. Group delay and dispersion tailoring in nonadiabatic tapered fibers

    NASA Astrophysics Data System (ADS)

    Mas, Sara; Palací, Jesús; Martí, Javier

    2016-09-01

    The dispersion profile of a nonadiabatic tapered singlemode fiber is characterized and dynamically tuned. Its group delay and dispersion parameters are measured and compared to those of a standard singlemode fiber. The dispersion profile can be tuned by introducing a phase shift through mechanical stretching. Coarse tuning is also obtained by varying the surrounding medium of the tapered fiber. Dispersion values up to 700 ps/nm·km in nonadiabatic tapered fibers are obtained for the first time. Dynamic tuning exposed here can be very useful in applications such as nonlinearities or soliton generation.

  13. Nonlinear transmission through a tapered fiber in rubidium vapor

    SciTech Connect

    Hendrickson, S. M.; Pittman, T. B.; Franson, J. D.

    2009-02-15

    Subwavelength-diameter tapered optical fibers surrounded by rubidium vapor can undergo a substantial decrease in transmission at high atomic densities due to the accumulation of rubidium atoms on the surface of the fiber. Here we demonstrate the ability to control these changes in transmission using light guided within the taper. We observe transmission through a tapered fiber that is a nonlinear function of the incident power. This effect can also allow a strong control beam to change the transmission of a weak probe beam.

  14. Some novel features of an FEL oscillator with tapered undulator

    SciTech Connect

    Saldin, E.L.; Schneidmiller, E.A.; Yurkov, M.V.

    1995-12-31

    A one-dimensional analysis of an FEL oscillator with a linear undulator tapering is presented. Some principally novel results have been obtained. The origin of these results is in principal difference between the FEL oscillator and an FEL amplifier. In the case of the FEL amplifier the frequency of the amplified wave and all the other parameters are defined by an experimenter. Contrary to this, the case of the FEL oscillator with tapered undulator is more complicated. The lasing frequency is defined by the maximum of the small-signal gain and depends on the tapering depth in some complex way.

  15. Biosensing platform with tapered optical microfibers: new results

    NASA Astrophysics Data System (ADS)

    King, Branden J.; Idehenre, Ighodalo; Powers, Peter E.; Haus, Joseph W.; Hansen, Karolyn M.

    2014-03-01

    Our research demonstrates the design and fabrication of a biosensor based on the tapered optical fiber. The fiber is tapered biconically to a diameter of approximately 7 μm, which allows the evanescent field of propagating light to interact with molecules attached to the tapered surface. This sensing platform is capable of fast, continuous, specific, sensitive, and label-free molecular detection in the aqueous phase. Detection is demonstrated across multiple fibers, and the individual fibers are reusable. The system described previously has been modified for detection of volatile organic compounds. The fabrication of the modified design is also shown with preliminary results.

  16. Aspects of geometric calculation of the planetary gear train with intermediate rollers. Part 1

    NASA Astrophysics Data System (ADS)

    I-Kan, An; Il'In, A. S.; Lazurkevich, A. V.

    2016-04-01

    The paper presents the geometric calculation of the planetary gear train with intermediate rollers, where the number of intermediate rollers is greater or less than that of the teeth in the annular gear by one, the profile surface of the annular gear teeth being the same. The gear ratio is changed by both a value and a sign.

  17. Textile processing improvements due to high speed roller ginning of upland cotton

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Selective breeding has improved upland cotton fiber properties. Processing capacities of new high-speed roller ginning technology approach that of saw ginning. Spinning mills are interested in mill performance data comparing new upland cultivars processed by both saw and roller ginning. Four dive...

  18. Comparison of high-speed roller and saw ginning on Texas high plains cotton

    Technology Transfer Automated Retrieval System (TEKTRAN)

    New high-quality cotton cultivars have been adopted in the Southern High Plains recently and, as a result, interest has grown in finding harvest and ginning practices that better preserve fiber quality. Advancements in roller ginning technology have increased the ginning rate of some roller gins to ...

  19. Fatigue performance and equations of roller compacted concrete with fly ash

    SciTech Connect

    Sun, W.; Liu, J.; Qin, H.; Zhang, Y.; Jin, Z.; Qian, M.

    1998-02-01

    In this paper, the influence of fly ash on the fatigue performance of roller compacted concrete was studied. The fatigue equations of roller compacted concrete without and with fly ash, which can be used for designing pavement, are proposed through the method of the regressive analysis, and compared with that of the same grade common concrete pavement.

  20. Radiation Effects on Fused Biconical Taper Wavelength Division Multiplexers

    NASA Technical Reports Server (NTRS)

    Gutierrez, Roman C.; Swift, Gary M.; Dubovitsky, Serge; Bartman, Randall K.; Barnes, Charles E.; Dorsky, Leonard

    1994-01-01

    The effects of radiation on fused biconical taper wavelength division multiplexers are presented. A theoretical model indicates that index changes in the fiber are primarily responsible for the degradation of these devices.

  1. Optical coupling and splitting with two parallel waveguide tapers.

    PubMed

    Tao, S H

    2011-01-17

    A coupling and splitting device comprising a width taper and a spatial-modulated subwavelength grating waveguide (SSGW) is proposed. The width taper is a waveguide with increasing width and the SSGW is a waveguide grating whose width and thickness are constant but the filling factor increases along the light propagation. Thus, the effective index of the subwavelength grating increases according to the effective medium theory. Light of orthogonal polarizations from a single-mode fiber can be coupled efficiently with the two parallel tapers. Furthermore, the coupled lights of orthogonal polarizations in the two tapers can be further split with connecting bent waveguides. Fabrication of the device is fully compatible with current complementary metal oxide semiconductor technology.

  2. A broadband tapered nanocavity for efficient nonclassical light emission.

    PubMed

    Gregersen, Niels; McCutcheon, Dara P S; Mørk, Jesper; Gérard, Jean-Michel; Claudon, Julien

    2016-09-01

    We present the design of a tapered nanocavity, obtained by sandwiching a photonic wire section between a planar gold reflector and a few-period Bragg mirror integrated into the tapered wire. Thanks to its ultrasmall mode volume (0.71 λ3/n3), this hybrid nanocavity largely enhances the spontaneous emission rate of an embedded quantum dot (Purcell factor: 6), while offering a wide operation bandwidth (full-width half-maximum: 20 nm). In addition, the top tapered section shapes the cavity far-field emission into a very directive output beam, with a Gaussian spatial profile. For realistic taper dimensions, a total outcoupling efficiency to a Gaussian beam of 0.8 is predicted. Envisioned applications include bright sources of non-classical states of light, such as widely tunable sources of indistinguishable single photons and polarization-entangled photon pairs. PMID:27607694

  3. Tapered fluorotellurite microstructured fibers for broadband supercontinuum generation.

    PubMed

    Wang, Fang; Wang, Kangkang; Yao, Chuanfei; Jia, Zhixu; Wang, Shunbin; Wu, Changfeng; Qin, Guanshi; Ohishi, Yasutake; Qin, Weiping

    2016-02-01

    Fluorotellurite microstructured fibers (MFs) based on TeO2-BaF2-Y2O3 glasses are fabricated by using a rod-in-tube method. Tapered fluorotellurite MFs with varied transition region lengths are prepared by employing an elongation machine. By using a tapered fluorotellurite MF with a transition region length of ∼3.3  cm as the nonlinear medium and a 1560 nm femtosecond fiber laser as the pump source, broadband supercontinuum generation covering from 470 to 2770 nm is obtained. The effects of the transition region length of the tapered fluorotellurite MF on supercontinuum generation are also investigated. Our results show that tapered fluorotellurite MFs are promising nonlinear media for generating broadband supercontinuum light expanding from visible to mid-infrared spectral region. PMID:26907442

  4. Phase sensitive signal analysis for bi-tapered optical fibers

    NASA Astrophysics Data System (ADS)

    Ben Harush Negari, Amit; Jauregui, Daniel; Sierra Hernandez, Juan M.; Garcia Mina, Diego; King, Branden J.; Idehenre, Ighodalo; Powers, Peter E.; Hansen, Karolyn M.; Haus, Joseph W.

    2016-03-01

    Our study examines the transmission characteristics of bi-tapered optical fibers, i.e. fibers that have a tapered down and up span with a waist length separating them. The applications to aqueous and vapor phase biomolecular sensing demand high sensitivity. A bi-tapered optical fiber platform is suited for label-free biomolecular detection and can be optimized by modification of the length, diameter and surface properties of the tapered region. We have developed a phase sensitive method based on interference of two or more modes of the fiber and we demonstrate that our fiber sensitivity is of order 10-4 refractive index units. Higher sensitivity can be achieved, as needed, by enhancing the fiber design characteristics.

  5. 5 W frequency stabilized 976 nm tapered diode lasers

    NASA Astrophysics Data System (ADS)

    Friedmann, Patrick; Gilly, Jürgen; Moritz, Stefan; Ostendorf, Ralf; Kelemen, Márc T.

    2008-02-01

    More and more applications, like tunable frequency doubling of diode lasers for blue-green outputs, non linear spectroscopy, or pump laser sources for fiber lasers necessitate diffraction-limited tunable narrow linewidths and high output powers in the multiwatt regime. For these applications, tapered lasers based on a tapered amplifier with gain-guided design can be used in an external cavity set up to guarantee both - frequency stabilization and tunability. We have realized frequency stabilized high-power ridge-waveguide tapered diode lasers with more than 4W of cw output power. These low modal gain, single quantum well InGaAs/AlGaAs devices emitting between 920nm and 1064nm were grown by molecular beam epitaxy. Tapered single emitters consist of an index-guided ridge section and a gain-guided taper section with an overall length of 3.5mm. The taper angle was 6°. With a high-reflectivity coating on the rear facet and an antireflection coating on the front facet more than 10W of output power have been demonstrated. To optimize the beam quality at higher output power the two different sections have been operated by different operation currents. For this purpose the tapered diodes have been mounted p-side down on structured submounts. For wavelength tunability and frequency stabilization the tapered diodes, provided with AR coatings on both facets, have been used in external cavity setup in Littrow configuration. The influence of the different operation currents on the electrooptical and beam characteristics has been carefully investigated in detail. Within this operation mode a nearly diffraction limited behavior up to 5W has been established.

  6. Antenna phase center locations in tapered aperture subarrays

    NASA Astrophysics Data System (ADS)

    Doerry, A. W.; Bickel, D. L.

    2016-05-01

    Antenna apertures are often parsed into subapertures for Direction of Arrival (DOA) measurements. However, when the overall aperture is tapered for sidelobe control, the locations of phase centers for the individual subapertures are shifted due to the local taper of individual subapertures. Furthermore, individual subaperture gains are also affected. These non-uniform perturbations complicate DOA calculations. Techniques are presented to calculate subaperture phase center locations, and algorithms are given for equalizing subapertures' gains.

  7. Multimode tapered optical light pipe for illumination systems

    NASA Astrophysics Data System (ADS)

    Romańczuk, Patryk; Pietrzycki, Marcin; Źmojda, Jacek; Kochanowicz, Marcin; Dorosz, Dominik

    2015-09-01

    In the article the multimode tapered optical light pipe for illumination systems was investigated. Based on tree light emitting diodes at the wavelength of 460 nm (blue), 528 nm (green) and 631 nm (red) possibility of white light emission on the output surface of the tapered light pipe was submitted. Influence of optical power of LEDs on the colour coordinates (CIE-1931) has been investigated.

  8. Instantaneous fault frequencies estimation in roller bearings via wavelet structures

    NASA Astrophysics Data System (ADS)

    Rodopoulos, Konstantinos I.; Antoniadis, Ioannis A.

    2016-11-01

    The main target of the current paper is the effective application of the method proposed in "Antoniadis et al. (2014) [17], in roller bearings under variable speed. For this reason, roller bearing model with slip and real data coming from a test rig has been used. The method extracts useful information from a complicated signal where the overlap among the harmonics can raise up to 30%. According to the proposed method, a set of wavelet transforms of the signal is first obtained, using a structure of Complex Shifted Morlet Wavelets. The center frequencies and the bandwidths of the individual wavelets, as well as the number of wavelets used, are associated with the characteristic fault frequency and its harmonic components. In this way, a set of complex signals result in the time domain, equal to the number of the wavelets used. Then, the instantaneous frequencies of the signals are estimated by applying an appropriate subspace algorithm (as for e.g. ESPRIT), to the entire set of the resulting complex wavelet transforms, exploiting the corresponding subspace rotational invariance property of this set of complex signals. The iterative procedure brings up accurate results from complicated signals, separating the fault associated signal components. Also, the spectrograms of the processed signals confirm the ability to match excited areas with specific faults.

  9. Transient dynamic analysis of high-speed lightly loaded cylindrical roller bearings. 2: Computer program and results

    NASA Technical Reports Server (NTRS)

    Conry, T. F.; Goglia, P. R.

    1981-01-01

    The governing differential equations of motion for a high speed cylindrical roller bearing are programmed for numerical solution and plotted output. This computer program has the capability of performing a two dimensional or three dimensional simulation. Two numerical solutions of the governing differential equations were obtained to simulate the motion of a roller bearing, one for the two dimensional equations of motion and one for the three dimensional equations of motion. Computer generated plots were obtained and present such data as roller/cage interaction forces, roller/race traction forces, roller/race relative slip velocities and cage angular speed over a nondimensional time equivalent to 1.2 revolutions of the inner race. Roller axial displacement, roller skew angle, and skew moment are also plotted for the three dimensional solution. The trajectory of the cage center is plotted for both the two dimensional and three dimensional solutions.

  10. Space Shuttle Orbiter Atlantis Liquid Oxygen Prevalve Detent Roller Cracking Investigation

    NASA Technical Reports Server (NTRS)

    Holleman, Elizabeth; Eddleman, David; Richard, James; Jacobs, Rebecca

    2008-01-01

    During routine inspections of the Space Shuttle's Main Propulsion System (MPS) Liquid Oxygen (LO2) pre-valve, the mechanism provided to maintain the valve in the open position was found cracked. The mechanism is a Vespel roller held against the valve visor by a stack of Belleville springs. The roller has been found cracked 3 times. All three instances were in the same valve in the same location. There are 6 pre-valves on each orbiter, and only one has exhibited this problem. Every-flight inspections were instituted and the rollers were found to be cracked after only one flight. Engineers at Marshall Space Flight Center, Johnson Space Center and Kennedy Space Center worked together to determine a solution. There were several possible contributors to the failure: a mis-aligned visor, an out of specification edge with a sharp radius, an out of specification tolerance stack up of a Belleville spring stack that caused un-predicted loads on the Vespel SP-21 roller, and a dimple machined into the side of the roller to indicate LO2 compatibility that created a stress riser. The detent assembly was removed and replaced with parts that were on the low-side of the tolerance stack up to eliminate the potential for high loads on the detent roller. After one flight, the roller was inspected and showed fewer signs of wear and no cracks.

  11. Space Shuttle Orbiter Atlantis Liquid Oxygen Pre-Valve Detent Roller Cracking Investigation

    NASA Technical Reports Server (NTRS)

    Holleman, Elizabeth; Eddleman, David; Jacobs, Rebecca; Richard, James

    2008-01-01

    During routine inspections of the Space Shuttle s Main Propulsion System Liquid Oxygen (LO2) pre-valve, the mechanism provided to maintain the valve in the open position was found cracked. The mechanism is a Vespel roller held against the valve visor by a stack of Belleville springs. The roller has been found cracked 3 times. All three instances were in the same valve in the same location. There are 6 pre-valves on each orbiter, and only one has exhibited this problem. Every-flight inspections were instituted and the rollers were found to be cracked after only one flight. Engineers at Marshall Space Flight Center, Johnson Space Center, and Kennedy Space Center worked together to determine a solution. There were several possible contributors to the failure: a misaligned visor, an out-of-specification edge with a sharp radius, an out-of-specification tolerance stack up of a Belleville spring stack that caused un-predicted loads on the Vespel SP-21 roller, and a dimple machined into the side of the roller to indicate LO2 compatibility that created a stress riser. The detent assembly was removed and replaced with parts that were on the low side of the tolerance stack up to eliminate the potential for high loads on the detent roller. After one flight, the roller was inspected and showed fewer signs of wear and no cracks.

  12. Principle of reflecting measurement system for roller wear and software simulation

    NASA Astrophysics Data System (ADS)

    Zheng, Longjiang; Wang, Kai; Guo, Yuan; Wang, Yutian

    2006-11-01

    Roller plays an important role in rolling mill. However, the effective surface of roller is limited. After long time working, the surface of roller will wear. The roller wear will result in difficult controlling of shape and thickness of steel board. Further more, it can lead to the decline of product quality. So the measurement of roller wear is very urgent for rolling mill to ensure their product quality. In this paper, a measurement method for roller wear is introduced in detail. This method offers advantages of sensitivity, immediate response, electromagnetic interference, simplicity and non-contact. It can detect in the atrocious condition on-line and examine roller wear precisely and real time. It is an effective method at low cost instance. The basic principle of this system is optical reflection principle. In the paper, after explaining the principle of this measurement system, an error compensation algorithm is exactly calculated to improve accuracy of this measurement system. This algorithm is brought out to offset the shift of measurement track. And a simulation-software program is compiled with Microsoft Visual Basic 6.0 based on this principle. By using this simulation-software, the date of I/O signal for this system is gained. And the signal verse is automatically drawn in this software.

  13. An Experimental Study of an FEL Oscillator with a Linear Taper

    SciTech Connect

    Benson, S.; Gubeli, J.; Neil, G.R.

    2001-01-01

    Motivated by the work of Saldin, Schneidmiller and Yurkov, we have measured the detuning curve widths, spectral characteristics, efficiency, and energy spread as a function of the taper for low and high Q resonators in the IR Demo FEL at Jefferson Lab. Both positive and negative tapers were used. Gain and frequency agreed reasonably well with the predictions of a single mode theory. The efficiency agreed reasonably well for a negative taper with a high Q resonator but disagreed for lower Q values due to the large slippage parameter and the non-ideal resonator Q. We saw better efficiency for a negative taper than for the same positive taper. The energy spread induced in the beam, normalized to the efficiency is larger for the positive taper than for the corresponding negative taper. This indicates that a negative taper is preferred over a positive taper in an energy recovery FEL.

  14. Fatigue delamination onset prediction in tapered composite laminates

    NASA Technical Reports Server (NTRS)

    Murri, Gretchen Bostaph; Salpekar, Satish A.; Obrien, T. Kevin

    1989-01-01

    Tapered (0 deg) laminates of S2/CE9000 and S2/SP250 glass/epoxies, and IM6/1827I graphite/epoxy were tested in cyclic tension. The specimens usually showed some initial stable delaminations in the tapered region, but these did not affect the stiffness of the specimens, and loading was continued until the specimens either delaminated unstably, or reached 10(exp 6) to 2 x 10(exp 7) million cycles with no unstable delamination. The final unstable delamination originated at the junction of the thin and tapered regions. A finite-element model was developed for the tapered laminate with and without the initial stable delaminations observed in the tests. The analysis showed that for both cases the most likely place for an opening (Mode 1) delamination to originate is at the junction of the taper and thin regions. For each material type, the models were used to calculate the strain energy release rate, G, associated with delaminations originating at that junction and growing either into the thin region or tapered region. For the materials tested, cyclic G(sub Imax) values from DCB tests were used with the maximum strain energy release rates calculated from the finite-element analysis to predict the onset of unstable delamination at the junction as a function of fatigue cycles. The predictions were compared to experimental values of maximum cyclic load as a function of cycles to unstable delamination from fatigue tests in tapered laminates. For the IM6/1827I and S2/SP250 laminates, the predictions agreed very well with the test data. Predicted values for the S2/CE9000 were conservative compared to the test data.

  15. Fabrication of polymer waveguide tapers to minimize insertion loss

    NASA Astrophysics Data System (ADS)

    Yacoubian, Araz; Lin, Weiping; Bechtel, James H.

    2001-12-01

    Polymer based electro-optic (EO) modulators and other integrated optic devices have the potential to provide low cost and lightweight alternative for high-speed digital as well as analog RF links. To be truly competitive with existing technologies such as LiNbO3, EO polymer modulators must also meet the criteria of low loss. There are two major causes of loss in EO modulators: waveguide loss (including material loss, scattering, etc.), and fiber- to-waveguide coupling (butting) loss. Various techniques can be utilized to minimize these coupling losses, however, to maintain low cost of component, we resort to the simplest possible approach which is easy to manufacture. Pigtails using standard single mode fiber produce coupling loss on the order of 3 to 5 dB/connection. In order to improve mode size matching yet maintain low drive voltage we incorporate waveguide and fibers tapers. Waveguide tapers resulted to butting losses as low as 1.5 dB/connection, whereas fiber tapers resulted to 2.5 dB/connection butting losses. Combining both techniques together, it was possible to produce 1.3 dB/connection butting loss, however, tapered waveguide devices were less sensitive to alignment tolerance than tapered fiber devices, and therefore less sensitive to environmental conditions.

  16. Roller Bearing Health Monitoring Using CPLE Frequency Analysis Method

    NASA Technical Reports Server (NTRS)

    Jong, Jen-Yi; Jones, Jess H.

    2007-01-01

    This paper describes a unique vibration signature analysis technique Coherence Phase Line Enhancer (CPLE) Frequency Analysis - for roller bearing health monitoring. Defects of roller bearing (e.g. wear, foreign debris, crack in bearing supporting structure, etc.) can cause small bearing characteristic frequency shifts due to minor changes in bearing geometry. Such frequency shifts are often too small to detect by the conventional Power Spectral Density (PSD) due to its frequency bandwidth limitation. This Coherent Phase Line Enhancer technology has been evolving over the last few years and has culminated in the introduction of a new and novel frequency spectrum which is fully described in this paper. This CPLE technology uses a "key phasor" or speed probe as a preprocessor for this analysis. With the aid of this key phasor, this CPLE technology can develop a two dimensional frequency spectrum that preserves both amplitude and phase that is not normally obtained using conventional frequency analysis. This two-dimensional frequency transformation results in several newly defined spectral functions; i. e. CPLE-PSD, CPLE-Coherence and the CPLE-Frequency. This paper uses this CPLE frequency analysis to detect subtle, low level bearing related signals in the High Pressure Fuel Pump (HPFP) of the Space Shuttle Main Engine (SSME). For many rotating machinery applications, a key phasor is an essential measurement that is used in the detection of bearing related signatures. There are times however, when a key phasor is not available; i. e. during flight of any of the SSME turbopumps or on the SSME High Pressure Oxygen Turbopump (HPOTP) where no speed probe is present. In this case, the CPLE analysis approach can still be achieved using a novel Pseudo Key Phasor (PKP) technique to reconstruct a 1/Rev PKP signal directly from external vibration measurements. This paper develops this Pseudo Key Phasor technique and applies it to the SSME vibration data.

  17. The effect of primary loading on fatigue life of cylindrical roller bearings

    NASA Astrophysics Data System (ADS)

    Crețu, S. S.

    2016-08-01

    Experimental and theoretical works shown that if a roller-raceway rolling contact is loaded in the elastic-plastic domain then, after the first rolling cycles, the material elastically shakedowns to a slightly modified axial profile and stable compressive residual stresses. Fatigue life tests carried out on four groups of NJ206 cylindrical roller bearings pointed out the superiority of the bearings groups that primary supported a few cycles of rolling loading in the elastic-plastic domain. An elastic-perfect plastic analysis was performed to reveal the role played by the roller's crowning geometry, operating clearance, misalignment angle and operating loads on contact pressures distributions achieved between each roller and the corresponding inner and outer raceways. The modified reference rating lives, evaluated using the lamina technique, exposed a good agreement with the values provided by fatigue life tests.

  18. Strategies to simulate wheel-rail adhesion in degraded conditions using a roller-rig

    NASA Astrophysics Data System (ADS)

    Bosso, N.; Gugliotta, A.; Zampieri, N.

    2015-05-01

    Railway vehicles adopt mechatronic devices to maximize the traction/braking effort. These systems often use complex algorithms that require long experimental validation tests on track. The possibility to perform the same tests on a roller-rig gives the opportunity to simplify the validation activity, under safe conditions, and to reduce the costs. The main challenge is to be able to reproduce the same adhesion conditions on a roller-rig with respect to the track, especially in degraded conditions. First, the paper shows experiments performed to reproduce degraded adhesion on a conventional roller-rig for a single wheelset. Then, an innovative roller-rig is proposed in order to reproduce the effect of the passage of several wheelsets on the track.

  19. Optical Tapers as White-Light WGM Resonators

    NASA Technical Reports Server (NTRS)

    Strekalov, Dmitry V.; Matsko, Andrey B.; Savchenkov, Anatoliy A.

    2010-01-01

    A theoretical analysis has revealed that tapered optical waveguides could be useful as white-light whispering-gallery-mode (WGM) optical resonators. The compactness and the fixed-narrow-frequency-band nature of the resonances of prior microdisk and microsphere WGM resonators are advantageous in low-power, fixed-narrow-frequency-band applications. However for optical-processing applications in which there are requirements for power levels higher and/or spectral responses broader than those of prior microdisk and microsphere WGM resonators, white-light WGM resonators in the form of optical tapers would be preferable. The theoretical analysis was performed for a multimode, axisymmetric, circular-cross-section waveguide having a taper sufficiently smooth and gradual to justify the approximation of adiabaticity. In this approximation, the equation for the dependence of the electromagnetic field upon the axial (longitudinal) waveguide coordinate can be separated from the equation for the dependence upon the radius and the azimuthal angle.

  20. Enhanced plasmonic nanofocusing of terahertz waves in tapered graphene multilayers.

    PubMed

    Liu, Weiwei; Wang, Bing; Ke, Shaolin; Qin, Chengzhi; Long, Hua; Wang, Kai; Lu, Peixiang

    2016-06-27

    We investigate the plasmonic nanofocusing of terahertz waves in tapered graphene multilayers separated by dielectrics. The nanofocusing effect is significantly enhanced in the graphene multilayer taper compared with that in a single layer graphene taper due to interlayer coupling between surface plasmon polaritons. The results are optimized by choosing an appropriate layer number of graphene and the field amplitude has been enhanced by 620 folds at λ = 50 μm. Additionally, the structure can slow light to a group velocity ~1/2815 of the light speed in vacuum. Our study provides a unique approach to compress terahertz waves into deep subwavelength scale and may find great applications in terahertz nanodevices for imaging, detecting and spectroscopy. PMID:27410629

  1. Head-neck taper corrosion in hip arthroplasty.

    PubMed

    Hussenbocus, S; Kosuge, D; Solomon, L B; Howie, D W; Oskouei, R H

    2015-01-01

    Modularity at the head-neck junction of the femoral component in THA became popular as a design feature with advantages of decreasing implant inventory and allowing adjustment of leg length, offset, and soft tissue balancing through different head options. The introduction of a new modular interface to femoral stems that were previously monoblock, or nonmodular, comes with the potential for corrosion at the taper junction through mechanically assisted crevice corrosion. The incidence of revision hip arthroplasty is on the rise and along with improved wear properties of polyethylene and ceramic, use of larger femoral head sizes is becoming increasingly popular. Taper corrosion appears to be related to all of its geometric parameters, material combinations, and femoral head size. This review article discusses the pathogenesis, risk factors, clinical assessment, and management of taper corrosion at the head-neck junction.

  2. Tapered rib fiber coupler for semiconductor optical devices

    DOEpatents

    Vawter, Gregory A.; Smith, Robert Edward

    2001-01-01

    A monolithic tapered rib waveguide for transformation of the spot size of light between a semiconductor optical device and an optical fiber or from the fiber into the optical device. The tapered rib waveguide is integrated into the guiding rib atop a cutoff mesa type semiconductor device such as an expanded mode optical modulator or and expanded mode laser. The tapered rib acts to force the guided light down into the mesa structure of the semiconductor optical device instead of being bound to the interface between the bottom of the guiding rib and the top of the cutoff mesa. The single mode light leaving or entering the output face of the mesa structure then can couple to the optical fiber at coupling losses of 1.0 dB or less.

  3. Head-Neck Taper Corrosion in Hip Arthroplasty

    PubMed Central

    Hussenbocus, S.; Kosuge, D.; Solomon, L. B.; Howie, D. W.; Oskouei, R. H.

    2015-01-01

    Modularity at the head-neck junction of the femoral component in THA became popular as a design feature with advantages of decreasing implant inventory and allowing adjustment of leg length, offset, and soft tissue balancing through different head options. The introduction of a new modular interface to femoral stems that were previously monoblock, or nonmodular, comes with the potential for corrosion at the taper junction through mechanically assisted crevice corrosion. The incidence of revision hip arthroplasty is on the rise and along with improved wear properties of polyethylene and ceramic, use of larger femoral head sizes is becoming increasingly popular. Taper corrosion appears to be related to all of its geometric parameters, material combinations, and femoral head size. This review article discusses the pathogenesis, risk factors, clinical assessment, and management of taper corrosion at the head-neck junction. PMID:25954757

  4. Tapered fiber optic sensor for potassium detection in distilled water

    NASA Astrophysics Data System (ADS)

    Yasin, M.; Pujiyanto, .; Apsari, R.; Tanjung, M.

    2015-01-01

    A simple sensor is proposed and demonstrated using a silica tapered fiber for sensing different concentration of potassium in de-ionized water. The tapered fiber is fabricated using a flame brushing technique to achieve a waist diameter and length of 10 μm and 80 mm, respectively. For a concentration change from 0 to 50 %, the ouput signal of the sensor decreases exponentially from -10.04 dBm to -11.11 dBm with linearity of more than 92%. The increment of potassium concentration increases the refractive index of the solution, which in turn reduces the index difference between core and cladding of the tapered fiber and thus allows more light to be leaked out from the fiber. This new potassium monitoring system provides numerous advantages such as simplicity of design and low cost of production.

  5. Enhanced broadband absorption in gold by plasmonic tapered coaxial holes.

    PubMed

    Mo, Lei; Yang, Liu; Nadzeyka, Achim; Bauerdick, Sven; He, Sailing

    2014-12-29

    Gold absorbers based on plasmonic tapered coaxial holes (PTCHs) are demonstrated theoretically and experimentally. An average absorption of over 0.93 is obtained theoretically in a broad wavelength range from 300 nm to 900 nm without polarization sensitivity due to the structural symmetry. Strong scattering of the incident light by the tapered coaxial holes is the main reason for the high absorption in the short wavelength range below about 550 nm, while gap surface plasmon polaritons propagating along the taper dominate the resonance-induced high absorption in the long wavelength range. Combining two PTCHs with different structural parameters can further enhance the absorption and thus increase the spectral bandwidth, which is verified by a sample fabricated by focused ion beam milling. This design is promising to be extended to other metals to realize effective and efficient light harvesting and absorption.

  6. Acoustic vibration sensor based on nonadiabatic tapered fibers.

    PubMed

    Xu, Ben; Li, Yi; Sun, Miao; Zhang, Zhen-Wei; Dong, Xin-Yong; Zhang, Zai-Xuan; Jin, Shang-Zhong

    2012-11-15

    A simple and low-cost vibration sensor based on single-mode nonadiabatic fiber tapers is proposed and demonstrated. The environmental vibrations can be detected by demodulating the transmission loss of the nonadiabatic fiber taper. Theoretical simulations show that the transmission loss is related to the microbending of the fiber taper induced by vibrations. Unlike interferometric sensors, this vibration sensor does not need any feedback loop to control the quadrature point to obtain a stable performance. In addition, it has no requirement for the coherence of the light source and is insensitive to temperature changes. Experimental results show that this sensing system has a wide frequency response range from a few hertz to tens of kilohertz with the maximal signal to noise ratio up to 73 dB.

  7. Acute effects of self-myofascial release using a foam roller on arterial function.

    PubMed

    Okamoto, Takanobu; Masuhara, Mitsuhiko; Ikuta, Komei

    2014-01-01

    Flexibility is associated with arterial distensibility. Many individuals involved in sport, exercise, and/or fitness perform self-myofascial release (SMR) using a foam roller, which restores muscles, tendons, ligaments, fascia, and/or soft-tissue extensibility. However, the effect of SMR on arterial stiffness and vascular endothelial function using a foam roller is unknown. This study investigates the acute effect of SMR using a foam roller on arterial stiffness and vascular endothelial function. Ten healthy young adults performed SMR and control (CON) trials on separate days in a randomized controlled crossover fashion. Brachial-ankle pulse wave velocity (baPWV), blood pressure, heart rate, and plasma nitric oxide (NO) concentration were measured before and 30 minutes after both SMR and CON trials. The participants performed SMR of the adductor, hamstrings, quadriceps, iliotibial band, and trapezius. Pressure was self-adjusted during myofascial release by applying body weight to the roller and using the hands and feet to offset weight as required. The roller was placed under the target tissue area, and the body was moved back and forth across the roller. In the CON trial, SMR was not performed. The baPWV significantly decreased (from 1,202 ± 105 to 1,074 ± 110 cm·s-1) and the plasma NO concentration significantly increased (from 20.4 ± 6.9 to 34.4 ± 17.2 μmol·L-1) after SMR using a foam roller (both p < 0.05), but neither significantly differed after CON trials. These results indicate that SMR using a foam roller reduces arterial stiffness and improves vascular endothelial function.

  8. Acute effects of self-myofascial release using a foam roller on arterial function.

    PubMed

    Okamoto, Takanobu; Masuhara, Mitsuhiko; Ikuta, Komei

    2014-01-01

    Flexibility is associated with arterial distensibility. Many individuals involved in sport, exercise, and/or fitness perform self-myofascial release (SMR) using a foam roller, which restores muscles, tendons, ligaments, fascia, and/or soft-tissue extensibility. However, the effect of SMR on arterial stiffness and vascular endothelial function using a foam roller is unknown. This study investigates the acute effect of SMR using a foam roller on arterial stiffness and vascular endothelial function. Ten healthy young adults performed SMR and control (CON) trials on separate days in a randomized controlled crossover fashion. Brachial-ankle pulse wave velocity (baPWV), blood pressure, heart rate, and plasma nitric oxide (NO) concentration were measured before and 30 minutes after both SMR and CON trials. The participants performed SMR of the adductor, hamstrings, quadriceps, iliotibial band, and trapezius. Pressure was self-adjusted during myofascial release by applying body weight to the roller and using the hands and feet to offset weight as required. The roller was placed under the target tissue area, and the body was moved back and forth across the roller. In the CON trial, SMR was not performed. The baPWV significantly decreased (from 1,202 ± 105 to 1,074 ± 110 cm·s-1) and the plasma NO concentration significantly increased (from 20.4 ± 6.9 to 34.4 ± 17.2 μmol·L-1) after SMR using a foam roller (both p < 0.05), but neither significantly differed after CON trials. These results indicate that SMR using a foam roller reduces arterial stiffness and improves vascular endothelial function. PMID:23575360

  9. Bilateral vertebral artery dissection possibly precipitated in delayed fashion as a result of roller coaster rides.

    PubMed

    Schneck, Michael; Simionescu, Monica; Bijari, Armita

    2008-01-01

    A 34-year-old woman presented with a 5-month history of persistent vertigo after multiple roller coaster rides, followed by neck pain for 1 month and then 2 weeks of blurred vision related to diplopia. She was ultimately found to have bilateral cervical vertebral artery dissection. The images are described and the literature is reviewed regarding late diagnosis of vertebral dissection and prior cases of roller coaster-associated dissection. PMID:18190821

  10. Single muscle fiber gene expression with run taper.

    PubMed

    Murach, Kevin; Raue, Ulrika; Wilkerson, Brittany; Minchev, Kiril; Jemiolo, Bozena; Bagley, James; Luden, Nicholas; Trappe, Scott

    2014-01-01

    This study evaluated gene expression changes in gastrocnemius slow-twitch myosin heavy chain I (MHC I) and fast-twitch (MHC IIa) muscle fibers of collegiate cross-country runners (n = 6, 20±1 y, VO₂max = 70±1 ml•kg-1•min-1) during two distinct training phases. In a controlled environment, runners performed identical 8 kilometer runs (30:18±0:30 min:s, 89±1% HRmax) while in heavy training (∼72 km/wk) and following a 3 wk taper. Training volume during the taper leading into peak competition was reduced ∼50% which resulted in improved race times and greater cross-section and improved function of MHC IIa fibers. Single muscle fibers were isolated from pre and 4 hour post run biopsies in heavily trained and tapered states to examine the dynamic acute exercise response of the growth-related genes Fibroblast growth factor-inducible 14 (FN14), Myostatin (MSTN), Heat shock protein 72 (HSP72), Muscle ring-finger protein-1 (MURF1), Myogenic factor 6 (MRF4), and Insulin-like growth factor 1 (IGF1) via qPCR. FN14 increased 4.3-fold in MHC IIa fibers with exercise in the tapered state (P<0.05). MSTN was suppressed with exercise in both fiber types and training states (P<0.05) while MURF1 and HSP72 responded to running in MHC IIa and I fibers, respectively, regardless of training state (P<0.05). Robust induction of FN14 (previously shown to strongly correlate with hypertrophy) and greater overall transcriptional flexibility with exercise in the tapered state provides an initial molecular basis for fast-twitch muscle fiber performance gains previously observed after taper in competitive endurance athletes. PMID:25268477

  11. Gap and channeled plasmons in tapered grooves: a review

    NASA Astrophysics Data System (ADS)

    Smith, C. L. C.; Stenger, N.; Kristensen, A.; Mortensen, N. A.; Bozhevolnyi, S. I.

    2015-05-01

    Tapered metallic grooves have been shown to support plasmons - electromagnetically coupled oscillations of free electrons at metal-dielectric interfaces - across a variety of configurations and V-like profiles. Such plasmons may be divided into two categories: gap-surface plasmons (GSPs) that are confined laterally between the tapered groove sidewalls and propagate either along the groove axis or normal to the planar surface, and channeled plasmon polaritons (CPPs) that occupy the tapered groove profile and propagate exclusively along the groove axis. Both GSPs and CPPs exhibit an assortment of unique properties that are highly suited to a broad range of cutting-edge nanoplasmonic technologies, including ultracompact photonic circuits, quantum-optics components, enhanced lab-on-a-chip devices, efficient light-absorbing surfaces and advanced optical filters, while additionally affording a niche platform to explore the fundamental science of plasmon excitations and their interactions. In this Review, we provide a research status update of plasmons in tapered grooves, starting with a presentation of the theory and important features of GSPs and CPPs, and follow with an overview of the broad range of applications they enable or improve. We cover the techniques that can fabricate tapered groove structures, in particular highlighting wafer-scale production methods, and outline the various photon- and electron-based approaches that can be used to launch and study GSPs and CPPs. We conclude with a discussion of the challenges that remain for further developing plasmonic tapered-groove devices, and consider the future directions offered by this select yet potentially far-reaching topic area.

  12. Stress Analysis of a New Disk-Type Variable Torque Slipping Clutch with Skewed Rollers

    NASA Astrophysics Data System (ADS)

    Feng, Ming; Ono, Kyosuke; Mimura, Kenji

    In this paper a new disk type of the variable torque slipping clutch with skewed rollers (VTSCSR) is presented and investigated both theoretically and experimentally. It is comprised of two flat disks, a number of skewed cylindrical rollers, and a cage. The slipping torque is produced by the skewed rollers rolling and slipping between the two disks. Based on the integral equation of the Boussinesq solution, the contact pressures are numerically calculated under the condition that the nonlinear equilibrium equations of the clutch elements are satisfied. By considering both pressure and friction, the components of subsurface stress are calculated from the integration of the Mindlin's subsurface stress equations of concentrated force. A numerical solver is then successfully developed by which the characteristics of the disk-type VTSCSR, including the torque capacity, angular velocities of the roller and cage, contact pressure and von Mises stress, etc, are calculated and illustrated for the typical designs. The influences on the distribution of the von Mises stress by applying various types of profiled rollers to the disk-type VTSCSR are also discussed. It has been found that the full crown with two arcs profiled roller can approximately give rise to the axially uniform distribution of the von Mises stress and therefore satisfies the design principle of the average damage of materials. In addition, the preliminary experiment was done in order to show the feasibility of this design idea and to verify the theoretical torque capacity.

  13. Armed Rollers: Does Nestling’s Vomit Function as a Defence against Predators?

    PubMed Central

    Parejo, Deseada; Avilés, Jesús M.; Peña, Aránzazu; Sánchez, Lourdes; Ruano, Francisca; Zamora-Muñoz, Carmen; Martín-Vivaldi, Manuel

    2013-01-01

    Chemical defences against predators are widespread in the animal kingdom although have been seldom reported in birds. Here, we investigate the possibility that the orange liquid that nestlings of an insectivorous bird, the Eurasian roller (Coracias garrulus), expel when scared at their nests acts as a chemical defence against predators. We studied the diet of nestling rollers and vomit origin, its chemical composition and deterrent effect on a mammal generalist predator. We also hypothesized that nestling rollers, as their main prey (i.e. grasshoppers) do from plants, could sequester chemicals from their prey for their use. Grasshoppers, that also regurgitate when facing to a threat, store the harmful substances used by plants to defend themselves against herbivores. We found that nestling rollers only vomit after being grasped and moved. The production of vomit depended on food consumption and the vomit contained two deterrent chemicals (hydroxycinnamic and hydroxybenzoic acids) stored by grasshoppers and used by plants to diminish herbivory, suggesting that they originate from the rollers’ prey. Finally, we showed for the first time that the oral secretion of a vertebrate had a deterrent effect on a model predator because vomit of nestling rollers made meat distasteful to dogs. These results support the idea that the vomit of nestling rollers is a chemical defence against predators. PMID:23874791

  14. Experimental Investigation of Superradiance in a Tapered Free-Electron Laser Amplifier

    SciTech Connect

    Hidaka, Y.; She, Y.; Murphy, J.B.; Podobedov, B.; Seletskiy, S.; Yang, X.

    2011-03-28

    We report experimental studies of the effect of undulator tapering on superradiance in a single-pass high-gain free-electron laser (FEL) amplifier. The experiments were performed at the Source Development Laboratory (SDL) of National Synchrotron Light Source (NSLS). Efficiency was nearly tripled with tapering. Both the temporal and spectral properties of the superradiant FEL along the uniform and tapered undulator were experimentally characterized using frequency-resolved optical gating (FROG) images. Numerical studies predicted pulse broadening and spectral cleaning by undulator tapering Pulse broadening was experimentally verified. However, spectral cleanliness degraded with tapering. We have performed first experiments with a tapered undulator and a short seed laser pulse. Pulse broadening with tapering expected from simulations was experimentally confirmed. However, the experimentally obtained spectra degraded with tapering, whereas the simulations predicted improvement. A further numerical study is under way to resolve this issue.

  15. Expanded-mode semiconductor laser with tapered-rib adiabatic-following fiber coupler

    SciTech Connect

    Vawter, G.A.; Smith, R.E.; Hou, H.; Wendt, J.R.

    1997-02-01

    A new diode laser using a Tapered-Rib Adiabatic-Following Fiber Coupler to achieve 2D mode expansion and narrow, symmetric far-field emission without epitaxial regrowth or sharply-defined tips on tapered waveguides is presented.

  16. Tapered plasma channels to phase-lock accelerating and focusing forces in laser-plasma accelerators

    SciTech Connect

    Rittershofer, W.; Schroeder, C.B.; Esarey, E.; Gruner, F.J.; Leemans, W.P.

    2010-05-17

    Tapered plasma channels are considered for controlling dephasing of a beam with respect to a plasma wave driven by a weakly-relativistic, short-pulse laser. Tapering allows for enhanced energy gain in a single laser plasma accelerator stage. Expressions are derived for the taper, or longitudinal plasma density variation, required to maintain a beam at a constant phase in the longitudinal and/or transverse fields of the plasma wave. In a plasma channel, the phase velocities of the longitudinal and transverse fields differ, and, hence, the required tapering differs. The length over which the tapered plasma density becomes singular is calculated. Linear plasma tapering as well as discontinuous plasma tapering, which moves beams to adjacent plasma wave buckets, are also considered. The energy gain of an accelerated electron in a tapered laser-plasma accelerator is calculated and the laser pulse length to optimize the energy gain is determined.

  17. The Frequency of Torsional Vibration of a Tapered Beam

    NASA Technical Reports Server (NTRS)

    Coleman, Robert

    1939-01-01

    A solution for the equation of torsional vibration of tapered beams has been found in terms of Bessel functions for beams satisfying the following conditions: (a) the cross sections along the span are similar in shape; and (b) the torsional stiffness of a section can be expressed as a power of a linear function of distance along the span. The method of applying the analysis to actual cases has been described. Charts are given from which numerical values can be immediately obtained for most cases of practical importance. The theoretical values of the frequency ratio have been experimentally checked on five beams having different amounts of taper.

  18. Impedance Scaling for Small-angle Tapers and Collimators

    SciTech Connect

    Stupakov, G.; /SLAC

    2010-02-11

    In this note I will prove that the impedance calculated for a small-angle collimator or taper, of arbitrary 3D profile, has a scaling property that can greatly simplify numerical calculations. This proof is based on the parabolic equation approach to solving Maxwell's equation developed in Refs. [1, 2]. We start from the parabolic equation formulated in [3]. As discussed in [1], in general case this equation is valid for frequencies {omega} >> c/a where a is a characteristic dimension of the obstacle. However, for small-angle tapers and collimators, the region of validity of this equation extends toward smaller frequencies and includes {omega} {approx} c/a.

  19. Bent optical fiber tapers for refractometery and biosensing

    NASA Astrophysics Data System (ADS)

    Penchev, Emil; Eftimov, Tinko; Bock, Wojtek

    2015-01-01

    We report the results of our study of the spectral shifts caused by surrounding refractive index changes (SRI) in bent fibre tapers. Fused and etched fibre tapers were fabricated using a gas burner and HF acid. Spectral shifts as high as 200 nm have been observed for SRI variations from 1.33 to 1.44 and sensitivity as high as 830 nm/r.i.u. around water RI values. We present results for refractometric measurements of cow milk of varying fat content and compare results with those obtained with conventional Abbe refractometers and high sensitivity double resonance LPGs.

  20. Tapered labyrinthine acoustic metamaterials for broadband impedance matching

    NASA Astrophysics Data System (ADS)

    Xie, Yangbo; Konneker, Adam; Popa, Bogdan-Ioan; Cummer, Steven A.

    2013-11-01

    We present five kinds of labyrinthine or space-coiling acoustic metamaterials with tapered channels and apertures. These designs exhibit negative index behavior with modest dispersion, and also have substantially improved impedance matching compared to previously investigated labyrinthine cells. Experimentally measured effective material parameters are in good agreement with numerically computed results for the first two designs. Numerical results are presented for the other three unit cells. By virtue of their design tunability and small size, these tapered labyrinthine acoustic metamaterials show potential as building blocks for a wide range of acoustic wave manipulation and imaging applications.

  1. Integrative Performance Analysis of a Novel Bone Level Tapered Implant.

    PubMed

    Dard, M; Kuehne, S; Obrecht, M; Grandin, M; Helfenstein, J; Pippenger, B E

    2016-03-01

    Primary mechanical stability, as measured by maximum insertion torque and resonance frequency analysis, is generally considered to be positively associated with successful secondary stability and implant success. Primary implant stability can be affected by several factors, including the quality and quantity of available bone, the implant design, and the surgical procedure. The use of a tapered implant design, for instance, has been shown to result in good primary stability even in clinical scenarios where primary stability is otherwise difficult to achieve with traditional cylindrical implants-for example, in soft bone and for immediate placement in extraction sockets. In this study, bone-type specific drill procedures are presented for a novel Straumann bone level tapered implant that ensure maximum insertion torque values are kept within the range of 15 to 80 Ncm. The drill procedures are tested in vitro using polyurethane foam blocks of variable density, ex vivo on explanted porcine ribs (bone type 3), and finally in vivo on porcine mandibles (bone type 1). In each test site, adapted drill procedures are found to achieve a good primary stability. These results are further translated into a finite element analysis model capable of predicting primary stability of tapered implants. In conclusion, we have assessed the biomechanical behavior of a novel taper-walled implant in combination with a bone-type specific drill procedure in both synthetic and natural bone of various types, and we have developed an in silico model for predicting primary stability upon implantation. PMID:26927485

  2. Taper-seal type metal sealing system and available applications

    NASA Astrophysics Data System (ADS)

    Kurokouchi, Satoshi; Okabe, Masayuki; Morita, Shinsaku

    2001-01-01

    A conventional disk (flat ring) gasket for ConFlat ® sealing system has been commonly applied to commercially available equipments for ultrahigh vacuum systems. However, its large redundant part which wastes the tightening force makes its handling and seal reliability problematic. We examine a taper-seal type gasket, which is newly designed to improve the inefficiency of ConFlat mechanism using conventional disk gaskets. It is remarked that the obtained seal area on a taper-seal type gasket is 1.6˜3.7 times larger than that of a conventional disk gasket. Our numencal results on stress distributions in a tightened gasket indicate that taper-seal gasket realizes highly stable seal pressure even under a lower tightening torque. High sealing reliability is thus achieved as expected which is mainly due to the wide seal area and stable seal pressure realized even for rather hard gasket material. Taper-seal type gasket also has some practical advantages. The most important of them may be that it enables to construct new edgeless metal sealing systems without a welded heavy flange. Here, edgeless sealing systems are composed of highly flexible incorporating viewports, bellows, feedthroughs, and blank-off covers, as well as any other conventional vacuum components.

  3. Nonlinear acoustic streaming in straight and tapered tubes

    NASA Astrophysics Data System (ADS)

    Tuttle, Brian C.

    In thermoacoustic and Stirling devices such as the pulse-tube refrigerator, efficiency is diminished by the formation of a second-order mean velocity known as Rayleigh streaming. This flow emerges from the interaction of the working gas with the wall of the tube in a thin boundary layer. Recent studies have suggested that streaming velocity can be decreased in a tube by tapering it slightly. This research investigates that claim through the development of a numerical model of Rayleigh streaming in variously tapered tubes. It is found that the numerical simulation of streaming in a straight tube compares well with theory, and the application of different thermal boundary conditions at the tube wall shows that for pressurized helium, inner streaming vortices which appear near an adiabatic tube wall do not develop near an isothermal wall. An order analysis indicates that the temperature dependence of viscosity and thermal conductivity contributes appreciably to an accurate numerical model of streaming. Comparison of Rayleigh streaming in tapered tubes shows the effects of taper angle on the circulation and velocity of the mean flow.

  4. Impedance Matching of Tapered Slot Antenna using a Dielectric Transformer

    NASA Technical Reports Server (NTRS)

    Simons, R. N.; Lee, R. Q.

    1998-01-01

    A new impedance matching technique for tapered slot antennas using a dielectric transformer is presented. The technique is demonstrated by measuring the input impedance, Voltage Standing Wave Ratio (VSWR) and the gain of a Vivaldi antenna (VA). Measured results at Ka-Band frequencies are presented and discussed.

  5. Opioid Abstinence Reinforcement Delays Heroin Lapse during Buprenorphine Dose Tapering

    ERIC Educational Resources Information Center

    Greenwald, Mark K.

    2008-01-01

    A positive reinforcement contingency increased opioid abstinence during outpatient dose tapering (4, 2, then 0 mg/day during Weeks 1 through 3) in non-treatment-seeking heroin-dependent volunteers who had been maintained on buprenorphine (8 mg/day) during an inpatient research protocol. The control group (n = 12) received $4.00 for completing…

  6. Efficiency optimization in a FEL with fields` nonadiabatic tapering

    SciTech Connect

    Goncharov, I.A.; Belyavskiy, E.D.; Silivra, A.A.

    1995-12-31

    Amplification of an electromagnetic wave in free electron lasers with a reversed guide field and right-hand polarized wiggler field is investigated both analytically and numerically. An effect of electron bunch trapping by the high frequency electromagnetic field is used for efficiency optimization. On the basis of motion stability criteria a possibility of bunches trapping by FEL parameters nonadiabatic (experimentally realizable) tapering is shown. The stability analysis of electron motion is based on Lyapunov theory for autonomy systems. A particle simulation is carried out for FEL parameters close to the experimental ones (relativistic factor {gamma}=4.75, wiggler field strength B{sub w}= 2.8 kG, guide field strength B{sub o}= -1.4 kG, operation wavelength {lambda}=6.2 mm) for the case of wiggler field tapering. Theoretically predicted rule of wiggler field tapering corresponding to FEL efficiency of 55% is approximated by stepped functions. For the experimentally realizable tapering it is found that FEL efficiency can be over 40%.

  7. Linearly tapered slot antenna circular array for mobile communications

    NASA Technical Reports Server (NTRS)

    Simons, Rainee N.; Kelly, Eron; Lee, Richard Q.; Taub, Susan R.

    1993-01-01

    The design, fabrication and testing of a conformal K-band circular array is presented. The array consists of sixteen linearly tapered slot antennas (LTSA). It is fed by a 1:16 microstrip line power splitter via electromagnetic coupling. The array has an omni-directional pattern in the azimuth plane. In the elevation plane the beam is displaced above the horizon.

  8. Using Tapered Block Copolymers to Create Conducting Nanomaterials

    NASA Astrophysics Data System (ADS)

    Epps, Thomas, III

    2014-03-01

    Soft materials, such as polymers, colloids, surfactants, and liquid crystals, are a technologically important class of matter employed in a variety of applications. One sub-class of soft material, block copolymers, provides the opportunity to design materials with attractive chemical and mechanical properties based on the ability to assemble into periodic structures with nanoscale domain spacings. Several applications for block copolymers currently under investigation in my group include battery and fuel cell membranes, analytical separations membranes, nano-tool templates, precursors to electronic arrays, and drug delivery vehicles. One area of recent progress in the group focuses on the behavior of conventional block copolymer and tapered block copolymer systems for lithium battery membrane applications. We find that we can tune poly(styrene- b-ethylene oxide) diblock copolymer nanostructures by adjusting the lithium counterion and lithium salt concentration, as well as the taper volume fraction and composition. Additionally, we can estimate the effective interaction parameters (χeff) for the salt-doped copolymers to determine the overall influence of tapering on the energetics of copolymer assembly. These tapered materials allow us to design nanostructured membrane systems with increased conductivity and improved mechanical properties in ion transport devices. We gratefully acknowledge AFOSR-PECASE (FA9550-09-1-0706) and NSF-CAREER (DMR-0645586) for financial support.

  9. Narcotic tapering in pregnancy using long-acting morphine

    PubMed Central

    Dooley, Roisin; Dooley, Joe; Antone, Irwin; Guilfoyle, John; Gerber-Finn, Lianne; Kakekagumick, Kara; Cromarty, Helen; Hopman, Wilma; Muileboom, Jill; Brunton, Nicole; Kelly, Len

    2015-01-01

    Abstract Objective To document the management of and outcomes for patients receiving narcotic replacement and tapering with long-acting morphine preparations during pregnancy. Design A prospective cohort study over 18 months. Setting Northwestern Ontario. Participants All 600 births at Meno Ya Win Health Centre in Sioux Lookout, Ont, from January 1, 2012, to June 30, 2013, including 166 narcotic-exposed pregnancies. Intervention Narcotic replacement and tapering of narcotic use with long-acting morphine preparations. Main outcome measures Prenatal management of maternal narcotic use, incidence of neonatal abstinence syndrome, and other neonatal outcomes. Results The incidence of neonatal abstinence syndrome fell significantly to 18.1% of pregnancies exposed to narcotics (from 29.5% in a previous 2010 study, P = .003) among patients using narcotic replacement and tapering with long-acting morphine preparations. Neonatal outcomes were otherwise equivalent to those of the nonexposed pregnancies. Conclusion In many patients, long-acting morphine preparations can be safely used and tapered in pregnancy, with a subsequent decrease in observed neonatal withdrawal symptoms. PMID:25821873

  10. Measurement and characterization of three-dimensional microstructures on precision roller surfaces

    NASA Astrophysics Data System (ADS)

    Kong, L. B.; Cheung, C. F.; Lee, W. B.; To, S.; Ren, M. J.

    2016-01-01

    Precision roller with microstructures is the key tooling component in the precision embossing by roller process such as Roll-to-Roll to manufacture optical plastic plates or films with three dimensional (3D)-microstructures. Measurement and analysis of 3D-microstructures on a precision roller is essential before the embossing process is being undertaken to ensure the quality of the embossed surfaces. Different from 3D-microstructures on a planar surface, it is difficult to measure and characterize the 3D-microstructures on the cylindrical surface of a precision roller due to the geometrical complexity of such integrated surfaces such as V-groove microstructures on a cylindrical surface. This paper presents a study of method and algorithms for the measurement and characterization of 3D-microstructures on a precision roller surface. A feature-based characterization method (FBCM) is proposed to analyze the V-groove microstructures. In this method, a normal template is generated based on the design specifications, and the measured data is fitted with the feature points. Hence alignment and matching of the measured data to the normal template based on the derived feature points are undertaken. After that the V-groove is characterized by some feature parameters such as pitch, depth, angle of the V-grooves. The method also provides an approach for the analysis of burs generated during the machining of Vgroove microstructures. A precision roller with V-groove microstructures has been machined by a Four-axis ultraprecision machine and the machined surface is measured by a contact measuring instrument. The measured data are then characterized and analyzed by the proposed FBCM. The results are presented and discussed, and they indicate the dominant and regular machining errors that are involved in the machining of the V-groove microstructures on roller surfaces.

  11. Loss Factor of Tapered Structures for Short Bunches

    SciTech Connect

    Blednykh, A.

    2011-03-28

    Using the electromagnetic simulation code ECHO, we have found a simple phenomenological formula that accurately describes the loss factor for short bunches traversing an axisymmetric tapered collimator. In this paper, we consider tapered collimators with rectangular cross-section and use the GdfidL code to calculate the loss factor dependence on the geometric parameters for short bunches. The results for both axisymmetric and rectangular collimators are discussed. The behaviour of the impedance of tapered structures for very short bunches in the optical regime has been determined in refs. [10,11]. Here, for the loss factors for two particular geometries, we have studied the departure from the optical regime behaviour as bunch length is increased. In both cases, the ratio of the loss factor for the tapered collimator to the loss factor in the optical regime is a function only of the scaling parameter {sigma}L/d{sup 2}. The fact that the bunch length a and the taper length L appear as a product is consistent with the recent scaling derived by Stupakov in ref. [12], since there is only a weak dependence on g. One noteworthy fact that is not a priori expected is that only the larger radius or vertical half-aperture d appears. The reduction factor is independent of b. Moreover, it is striking that the specific form involving the arctan given in Eq. (5) holds for both geometries, with only the coefficient {mu} differing by a factor of {approx}2 for flat vs round. This suggests that there may be a useful phenomenological form for more general geometries which may follow from natural extensions of Eq. (5). This possibility is presently being investigated.

  12. New roller pump disposable provides safety and simplifies occlusion setting.

    PubMed

    Lee-Sensiba, K; Azzaretto, N; Carolina, C; DiCarmine, N; Hymowitz, D; Kay, S; Kooker, K; Salogub, M; Wong, E; Tamari, Y

    1997-03-01

    A new disposable insert for the arterial roller pump, the Better-Header, provides safety and functionality beyond what standard tubing provides. It automatically limits pump outlet pressure to a level determined by the user and provides a self-contained, simple means to set pump occlusion. The Better-Header consists of a Starling-like pressure relief valve connected across standard header tubing. As long as arterial line pressure at the pump outlet remains below a set limit, the valve is closed. If line pressure approaches the pressure limit, the valve opens, preventing overpressurization by shunting blood from pump outlet to inlet. The Better-Header can also be used to set occlusion by the "dynamic method" to obtain nonocclusive settings. The Better-Header was evaluated in the lab for its pressure-flow characteristics. Even when the arterial line was completely clamped at a pump flow of 7 L/min, line pressure was limited to a safe level and all circuit connections were preserved. The Better-Header has been used successfully at North Shore University Hospital in over 500 clinical cases covering a wide range of patients and procedures. In several instances, the user was alerted to high pressure situations by fluid flow through the valve and by an audible alarm, allowing rapid correction of the source of pressure. Compared to the standard setup, the Better-Header maintains outlet pressure within safe, user-settable limits, and permits consistent, nonocclusive settings with predictable retrograde flow.

  13. Modeling Oxygen Uptake during V1 Treadmill Roller Skiing

    PubMed Central

    BOWEN, ROBERT S.; JENSEN, RANDALL L.; RYAN, JENNIFER M.; WATTS, PHILLIP B.

    2009-01-01

    The use of regression equations to predict oxygen uptake in relation to speed, grade, power output, and anthropometric characteristics is common in cardiac rehabilitation and athlete fitness testing. Research has suggested that sport specific testing improves the reliability of the test methodology and is appropriate for the development of effective training programs. This study focused on the development of a cross-country skiing specific predictor of maximal oxygen uptake based on treadmill speed, treadmill grade, gender, and body mass. This project simulated snow skiing on a large research treadmill using roller skis. A small sample size (N = 34) warranted the use of bootstrapping techniques and multiple regression analysis to develop a cross-country skiing specific model of oxygen uptake. The stability of each bootstrapped sample was confirmed via a cross-validation procedure. The equation of best resolve was: VO2 = −4.534 + 0.223(G) + 0.061(BM) + 0.139(TG) + 0.016(TS) in which G = Gender, BM = Body Mass, TG = Treadmill Grade, TS = Treadmill Speed. The resultant model can be used to design training programs, develop athlete fitness testing or research protocols, and to predict maximal oxygen uptake when sophisticated metabolic measurement equipment is unavailable. PMID:27182311

  14. Deep-blue supercontinnum sources with optimum taper profiles--verification of GAM.

    PubMed

    Sørensen, S T; Møller, U; Larsen, C; Moselund, P M; Jakobsen, C; Johansen, J; Andersen, T V; Thomsen, C L; Bang, O

    2012-05-01

    We use an asymmetric 2 m draw-tower photonic crystal fiber taper to demonstrate that the taper profile needs careful optimisation if you want to develop a supercontinuum light source with as much power as possible in the blue edge of the spectrum. In particular we show, that for a given taper length, the downtapering should be as long as possible. We argue how this may be explained by the concept of group-acceleration mismatch (GAM) and we confirm the results using conventional symmetrical short tapers made on a taper station, which have varying downtapering lengths. PMID:22565689

  15. Characteristics of a tapered capillary plasma waveguide for laser wakefield acceleration

    SciTech Connect

    Kim, M. S.; Jang, D. G.; Lee, T. H.; Nam, I. H.; Lee, I. W.; Suk, H.

    2013-05-20

    We developed a gas-filled capillary with a tapered density for laser wakefield acceleration, of which the tapering was realized by employing gas feed-lines with different cross-sections. Plasma diagnostics show that the capillary plasma has a significant longitudinal density tapering and a transverse parabolic profile. By using the tapered capillary plasma, high transmission (over 90%) of laser beams, meaning good optical guiding, was observed. These results demonstrate the potential of the tapered plasma source for high-energy laser wakefield acceleration, where the dephasing problem is minimized.

  16. Refractive index sensors based on the fused tapered special multi-mode fiber

    NASA Astrophysics Data System (ADS)

    Fu, Xing-hu; Xiu, Yan-li; Liu, Qin; Xie, Hai-yang; Yang, Chuan-qing; Zhang, Shun-yang; Fu, Guang-wei; Bi, Wei-hong

    2016-01-01

    In this paper, a novel refractive index (RI) sensor is proposed based on the fused tapered special multi-mode fiber (SMMF). Firstly, a section of SMMF is spliced between two single-mode fibers (SMFs). Then, the SMMF is processed by a fused tapering machine, and a tapered fiber structure is fabricated. Finally, a fused tapered SMMF sensor is obtained for measuring external RI. The RI sensing mechanism of tapered SMMF sensor is analyzed in detail. For different fused tapering lengths, the experimental results show that the RI sensitivity can be up to 444.517 81 nm/RIU in the RI range of 1.334 9—1.347 0. The RI sensitivity is increased with the increase of fused tapering length. Moreover, it has many advantages, including high sensitivity, compact structure, fast response and wide application range. So it can be used to measure the solution concentration in the fields of biochemistry, health care and food processing.

  17. Roller coaster-associated subarachnoid hemorrhage--report of 2 cases.

    PubMed

    Rutsch, Sebastian; Niesen, Wolf-Dirk; Meckel, Stephan; Reinhard, Matthias

    2012-04-15

    The most common neurological injuries associated with roller coaster rides are subdural hematoma and cervical artery dissection. We report two cases of roller-coaster associated subarachnoid hemorrhage (SAH). A 40-year-old healthy man developed a strong, holocephalic headache during a roller coaster ride. SAH Hunt & Hess grade II and Fisher grade 3 was diagnosed. An underlying aneurysm of the anterior communicating artery was successfully treated with coil embolization. A 41-year-old female (smoker, otherwise healthy) experienced a sudden, strong headache and diplopia during a roller coaster ride. A perimesencephalic SAH (Hunt & Hess grade II, Fisher grade 3) was disclosed by a CT scan. No aneurysm was detected on angiography. Both patients were discharged without neurological disability. In conclusion, SAH is a rare but relevant differential diagnosis in cases of acute headache during roller coaster rides. Both aneurysmal and non-aneurysmal perimesencephalic SAH can occur. A combination of mechanical factors and excessive blood pressure rises in vulnerable persons is discussed. PMID:22177088

  18. Oxygen mass transfer and scale-up studies in baffled roller bioreactors.

    PubMed

    Nikakhtari, H; Song, W; Nemati, M; Hill, G A

    2014-02-01

    Oxygen mass transfer was studied in conventional, bead mill and baffled roller bioreactors. Using central composite rotational design, impacts of size, rotation speed and working volume on the oxygen mass transfer were evaluated. Baffled roller bioreactor outperformed its conventional and bead mill counterparts, with the highest k(L)a obtained in these configurations being 0.58, 0.19, 0.41 min(-1), respectively. Performances of the bead mill and baffled roller bioreactor were only comparable when a high bead loading (40%) was applied. Regardless of configuration increase in rotation speed and decrease in working volume improved the oxygen mass transfer rate. Increase in size led to enhanced mass transfer and higher k(L)a in baffled roller bioreactor (0.49 min(-1) for 2.2 L and 1.31 min(-1) for 55 L bioreactors). Finally, the experimentally determined k(L)a in the baffled roller bioreactors of different sizes fit reasonably well to an empirical correlation describing the k(L)a in terms of dimensionless numbers.

  19. Improving the granule strength of roller-compacted ibuprofen sodium for hot-melt coating processing.

    PubMed

    Lopes, Diogo Gomes; Garsuch, Verena; Becker, Karin; Paudel, Amrit; Stehr, Michael; Zimmer, Andreas; Salar-Behzadi, Sharareh

    2016-08-20

    Solvent-free hot-melt coating processing is a novel and cost-efficient approach to manufacturing taste-masked multiparticulate systems. However, most API powders are fine and cohesive and not processable by hot-melt coating. The aim of this study was to produce dense and abrasion-resistant granules with high drug content (>80%) via roller compaction for hot-melt coating process optimization. The selected API was ibuprofen sodium dihydrate, a salt of ibuprofen with improved bioavailability and poor intrinsic compactibility. The formulation and roller compaction process were developed for the production of granules with 94%w/w of API and low friability (∼30%), using sorbitol and isomalt as excipients. The strong bonding mechanism relied on powder jamming prior to the rollers and was investigated via scanning electron microscopy, differential scanning calorimetry and small and wide angle X-ray scattering. It was shown that sorbitol crystals are solubilized during roller compaction and recrystallize as sorbitol hydrate, acting as strong solid bridges. The robustness of the roller compaction process and the re-compaction of fines were investigated. A statistical design of experiments was conducted to evaluate the hot-melt coating process for taste masking of ibuprofen sodium granules. Taste masking required coating ratios higher than 40%w/w of granule batch, emphasizing the need for high-drug-content and abrasion-resistant granules.

  20. Unified compaction curve model for tensile strength of tablets made by roller compaction and direct compression.

    PubMed

    Farber, Leon; Hapgood, Karen P; Michaels, James N; Fu, Xi-Young; Meyer, Robert; Johnson, Mary-Ann; Li, Feng

    2008-01-01

    A model that describes the relationship between roller-compaction conditions and tablet strength is proposed. The model assumes that compaction is cumulative during roller compaction and subsequent granule compaction, and compact strength (ribbon and tablet) is generated irreversibly as if strength is controlled by plastic deformation of primary particles only. Roller-compaction is treated as a compaction step where the macroscopic ribbon strength is subsequently destroyed in milling. This loss in strength is irreversible and tablets compressed from the resulting granulation are weaker than those compressed by direct compression at the same compression force. Roller-compacted ribbons were produced at a range of roll forces for three formulations and subsequently milled and compacted into tablets. Once the total compaction history is taken in account, the compaction behavior of the uncompacted blends and the roller-compacted granules ultimately follow a single master compaction curve--a unified compaction curve (UCC). The model successfully described the compaction behavior of DC grade starch and formulations of lactose monohydrate with 50% or more microcrystalline cellulose, and may be more generally applicable to systems containing significant proportions of any plastically deforming material, including MCC and starch. PMID:17689211

  1. Towards the development of a work index for the Roller Press

    SciTech Connect

    Klymowsky, I.B.; Liu, J.

    1997-11-01

    This paper details the development of a functional work index that characterises the relationship between the energy that is imparted by a Roller Press into materials, against the resultant size reduction achieved. Such a Roller Press work index is necessary for this new grinding technology to differentiate it from Bond`s grinding work index, and to clear up confusion that arises with such comparison to Bond. The energy usage in a Roller Press does not follow Bond`s {open_quotes}Third Theory of Comminution{close_quotes} but rather Rittinger`s theory of new surface creation. The relationships for such a work index have been developed from the viewpoint of an equipment manufacturer with the hope that they will be of assistance to the minerals industry in the design of grinding circuits incorporating Roller Press comminution. The work index contains modification factors that reflects the effect of oversize, fines, moisture, closed-circuit operation and roll surface characteristics on the energy verses size reduction relationship. It has evolved from the results obtained from testing of a wide range of ore and mineral types that include bauxite, coal, kimberlite, limestone, iron and chrome ores, base metal and gold ores. The results show that even for such a diverse range of materials, they all demonstrate similarities of behaviour when comminuted in a Roller Press.

  2. Improving the granule strength of roller-compacted ibuprofen sodium for hot-melt coating processing.

    PubMed

    Lopes, Diogo Gomes; Garsuch, Verena; Becker, Karin; Paudel, Amrit; Stehr, Michael; Zimmer, Andreas; Salar-Behzadi, Sharareh

    2016-08-20

    Solvent-free hot-melt coating processing is a novel and cost-efficient approach to manufacturing taste-masked multiparticulate systems. However, most API powders are fine and cohesive and not processable by hot-melt coating. The aim of this study was to produce dense and abrasion-resistant granules with high drug content (>80%) via roller compaction for hot-melt coating process optimization. The selected API was ibuprofen sodium dihydrate, a salt of ibuprofen with improved bioavailability and poor intrinsic compactibility. The formulation and roller compaction process were developed for the production of granules with 94%w/w of API and low friability (∼30%), using sorbitol and isomalt as excipients. The strong bonding mechanism relied on powder jamming prior to the rollers and was investigated via scanning electron microscopy, differential scanning calorimetry and small and wide angle X-ray scattering. It was shown that sorbitol crystals are solubilized during roller compaction and recrystallize as sorbitol hydrate, acting as strong solid bridges. The robustness of the roller compaction process and the re-compaction of fines were investigated. A statistical design of experiments was conducted to evaluate the hot-melt coating process for taste masking of ibuprofen sodium granules. Taste masking required coating ratios higher than 40%w/w of granule batch, emphasizing the need for high-drug-content and abrasion-resistant granules. PMID:27346416

  3. Effect of Roller Profile on Cylindrical Roller Bearing Life Prediction. Part 1; Comparison of Bearing Life Theories

    NASA Technical Reports Server (NTRS)

    Poplawski, Joseph V.; Peters, Steven M.; Zaretsky, Erwin V.

    2001-01-01

    Four rolling-element bearing life theories were chosen for analysis and compared for a simple roller-race geometry model. The life theories were those of Weibull; Lundberg and Palmgren; Ioannides and Harris; and Zaretsky. The analysis without a fatigue limit of Ioannides and Harris is identical to the Lundberg and Palmgren analysis, and the Weibull analysis is similar to that of Zaretsky if the exponents are chosen to be identical. The resultant predicted life a each stress condition not only depends on the life equation used but also on the Weibull slope assumed. The least variation in predicted life with Weibull slope comes with the Zaretsky equation. Except for a Weibull slope of 1.11, at which the Weibull equation predicts the highest lives, the highest lives are predicted for the Zaretsky equation. For Weibull slopes of 1.5 and 2, both the Lundherg-Palmgren and Ioannides-Harris (where tau(sub u) = 0) equations predict lower lives than the ANSI/ABMA/ISO standard. Based upon the Hertz stresses for line contact, the accepted load-life exponent of 10/3 results in a maximum Hertz stress-life exponent equal to 6.6. This value is inconsistent with that experienced in the field. The assumption of as shear stress fatigue limit tau(sub u) results in Hertz stress-life exponents greater than are experimentally verifiable.

  4. Does Taper Angle Clearance Influence Fretting and Corrosion Damage at the Head-Stem Interface? A Matched Cohort Retrieval Study

    PubMed Central

    Kocagöz, Sevi B.; Underwood, Richard J.; Sivan, Shiril; Gilbert, Jeremy L.; MacDonald, Daniel W.; Day, Judd S.; Kurtz, Steven M.

    2014-01-01

    Previous studies have speculated that modular taper design may have an effect on the corrosion and material loss at the taper surfaces. We present a novel method to measure taper angle for retrieved head taper and stem trunnions using a roundness machine (Talyrond 585, Taylor Hobson, UK). We also investigated the relationship between taper angle clearance and visual fretting-corrosion score at the taper-trunnion junction using a matched cohort study of 50 ceramic and 50 metal head-stem pairs. In this study, no correlation was observed between the taper angle clearance and the visual fretting-corrosion scores in either the ceramic or the metal cohorts. PMID:24610994

  5. [Improvement of dissolution test using micro-controlled roller pump].

    PubMed

    Nagai, Noriaki; Konishi, Nahoko; Nitta, Tadahisa; Taga, Atsushi; Ito, Yoshimasa

    2012-01-01

    The dissolution test is a core performance test in pharmaceutical development and quality control of solid drug products. The conventional HPLC dissolution method (batch-sampling method) involves many steps including the filtration, collection and replenishment of sample solutions. We previously reported a dissolution test that involved microdialysis methods (microdialysis-HPLC method) and allowed many steps to be omitted. However, the recovery rate of theophylline by the microdialysis-HPLC method was lower, and the decrease in the flow rate through the dialysis probe caused variation between each tablet. In this study, we have attempted to improve the dissolution test by using a precise micro-controlled roller pump and microfiltering probe (microfiltering-HPLC method). Sustained release preparations of Theodur (100 mg) were used, and the test solutions used were water, buffer at pH 1.2 and pH 6.8, and pH 6.8-buffer containing 0.1-1% polysorbate 80 or sodium lauryl sulfate. In all test solutions, the microfiltering-HPLC method was able to accomplish continuous sampling of sample solutions, and the recovery rate of theophylline was over 90%. The dissolution behavior by the microfiltering-HPLC method tends to reflect the pharmaceutical design in comparison with the batch-sampling method, and the standard deviations by the microfiltering-HPLC are lower than with the batch-sampling method. In addition, the microfiltering-HPLC method allows many steps to be omitted, such as the filtration, collection and replenishment of sample solutions. These findings provide significant information that can be used in the pharmaceutical development and quality assessment of solid drug products.

  6. Nanocrystalline, superhard, ductile ceramic coatings for roller-cone bit bearings

    SciTech Connect

    Namavar, F.; Colter, P.; Karimy, H.

    1997-12-31

    The established method for construction of roller bits utilizes carburized steel, frequently with inserted metal bearing surfaces. This construction provides the necessary surface hardness while maintaining other desirable properties in the core. Protective coatings are a logical development where enhanced hardness, wear resistance, corrosion resistance, and surface properties are required. The wear properties of geothermal roller-cone bit bearings could be further improved by application of protective ceramic hard coatings consisting of nanometer-sized crystallites. Nanocrystalline protective coatings provide the required combination of hardness and toughness which has not been available thus far using traditional ceramics having larger grains. Increased durability of roller-cone bit bearings will ultimately reduce the cost of drilling geothermal wells through increased durability.

  7. Fully-automated roller bottle handling system for large scale culture of mammalian cells.

    PubMed

    Kunitake, R; Suzuki, A; Ichihashi, H; Matsuda, S; Hirai, O; Morimoto, K

    1997-01-20

    A fully automatic and continuous cell culture system based on roller bottles is described in this paper. The system includes a culture rack storage station for storing a large number of roller bottles filled with culture medium and inoculated with mammalian cells, mass-handling facility for extracting completed cultures from the roller bottles, and replacing the culture medium. The various component units of the system were controlled either by a general-purpose programmable logic controller or a dedicated controller. The system provided four subsequent operation modes: cell inoculation, medium change, harvesting, and medium change. The operator could easily select and change the appropriate mode from outside of the aseptic area. The development of the system made large-scale production of mammalian cells, and manufacturing and stabilization of high quality products such as erythropoietin possible under total aseptic control, and opened up the door for industrial production of physiologically active substances as pharmaceutical drugs by mammalian cell culture.

  8. Computational and experimental investigation of flow and particle settling in a roller bottle bioreactor.

    PubMed

    Muzzio, F J; Unger, D R; Liu, M; Bramble, J; Searles, J; Fahnestock, P

    1999-04-20

    It is shown that cell settling is a key factor affecting the performance of roller bottle bioreactors. The two-dimensional cross-sectional flow at the center of a roller bottle is simulated using a finite difference method, and the settling behavior of cells is simulated using particle dynamics algorithms and validated experimentally using fluorescent particles. The settling behavior of particles in the roller bottle flow is studied using both steady and time dependent rotation rates. Under steady flow conditions the flow is divided into two regions: one where the particles settle to the wall and one where the particles remain suspended indefinitely. The relative size of these two regions depends on the ratio of the settling velocity to the rotation rate of the bottle. For unsteady flows generated by periodic changes of the bottle rotation direction, the settling of cells is accelerated significantly, leading to complete deposition in just a few turns of the bottle. PMID:10099595

  9. Roller-style electrostatic printing of prepatterned few-layer-graphenes

    NASA Astrophysics Data System (ADS)

    Liang, Xiaogan; Giacometti, Valentina; Ismach, Ariel; Harteneck, Bruce D.; Olynick, Deirdre L.; Cabrini, Stefano

    2010-01-01

    Electrostatic exfoliation of patterned few-layer-graphenes was demonstrated using a method compatible with high throughput roll-to-roll manufacturing. A patterned graphite template was placed on a roller and used to exfoliate patterned graphene on a planar substrate. The exfoliated graphene features were subsequently characterized by Raman spectroscopy. In comparison with previously demonstrated planar electrostatic exfoliation approach, the roller-style method can create a narrower distribution of thickness of few-layer-graphenes, which is attributed to the combinational action of tangential rolling friction and electrostatic forces. This roller-style electrostatic printing technique could be applied for roll-to-roll manufacturing of graphene-based devices in the future.

  10. The tapered press fit total hip arthroplasty: a European alternative.

    PubMed

    Swanson, Todd V

    2005-06-01

    The tapered rectangular press fit femoral component design of Karl Zweymüller remains highly successful since its inception in 1979. The longitudinal taper and rectangular cross-section provide unequaled primary stability, which promotes consistent secondary osseointegration to the grit-blasted titanium surface, even in osteoporotic bone. The "fit without fill" concept provides for bone conservation and preservation of the intraosseous blood supply by compaction, rather than removal, of the metaphyseal cancellous bone. The surgical technique is simple and forgiving, allowing for infinite adjustability in stem height and anteversion. Numerous long-term studies report excellent clinical results with a negligible incidence of loosening, thigh pain, osteolysis, or significant stress shielding and survivorships approaching 100% at 10 years. PMID:15991133

  11. Complex coupled-mode theory for tapered optical waveguides.

    PubMed

    Mu, Jianwei; Huang, Wei-Ping

    2011-03-15

    A coupled-mode formulation based on complex local modes is developed for tapered and longitudinally varying optical waveguides. Different from the conventional coupled-mode theory that requires integration over the entire spectrum of radiation modes, the new formulation treats the radiation fields via discrete complex modes similarly to the guided modes. Accuracy, convergence, and scope of validity for the solutions of the complex coupled-mode equations are investigated in detail for a typical single-mode waveguide taper. It is demonstrated that the complex coupled-mode theory has overcome the difficulties of the conventional theory in simulation of radiation field effects while preserving the simplicity and intuitiveness of this popular method.

  12. Free-electron lasers with very slow wiggler taper

    SciTech Connect

    Bosley, D.L.; Kevorkian, J.

    1990-09-01

    A highly accurate, explicit asymptotic solution of the electron energy and phase is found for a class of free-electron lasers with very long wavelength beams, very low electron energies, and very slow taper of the wiggler field relative to the wiggler period. Dimensionless variables are defined and normalized, and three small parameters which characterize the operation of the FEL are identified. Because of the explicit nature of the solution, our results may be directly used to calculate features such as the escape distance of the electron from the potential well and the effects of the various physical parameters. One important advantage of the very slow wiggler taper is the increased efficiency of the energy transfer from the electron beam to the signal field due to increased bucket width. Numerical calculations are performed to verify all results. 9 refs., 6 figs.

  13. Color patterns in a tapered lightpipe with RGB LEDs

    NASA Astrophysics Data System (ADS)

    Esparza, Diego; Moreno, Ivan

    2010-08-01

    There is an enormous range of possible color distributions that may be created with a light cone when the primary source is an array of multicolor light-emitting diodes (LEDs). If one looks through a lightpipe toward an LED array, multiple images of the color LEDs can be observed as in a kaleidoscope. A tapered lightpipe behaves as a three-dimensional kaleidoscope, and then, by changing the position and orientation of the red-green-blue LEDs can produce a plenty of amazing illumination patterns. We analytically calculate this color spatial distribution of the illumination pattern produced by a tapered lightpipe. Moreover, we simulate these color illumination patterns, and analyze their structure and symmetry.

  14. Optimized tapered dipole nanoantenna as efficient energy harvester.

    PubMed

    El-Toukhy, Youssef M; Hussein, Mohamed; Hameed, Mohamed Farhat O; Heikal, A M; Abd-Elrazzak, M M; Obayya, S S A

    2016-07-11

    In this paper, a novel design of tapered dipole nanoantenna is introduced and numerically analyzed for energy harvesting applications. The proposed design consists of three steps tapered dipole nanoantenna with rectangular shape. Full systematic analysis is carried out where the antenna impedance, return loss, harvesting efficiency and field confinement are calculated using 3D finite element frequency domain method (3D-FEFD). The structure geometrical parameters are optimized using particle swarm algorithm (PSO) to improve the harvesting efficiency and reduce the return loss at wavelength of 500 nm. A harvesting efficiency of 55.3% is achieved which is higher than that of conventional dipole counterpart by 29%. This enhancement is attributed to the high field confinement in the dipole gap as a result of multiple tips created in the nanoantenna design. Furthermore, the antenna input impedance is tuned to match a wide range of fabricated diode based upon the multi-resonance characteristic of the proposed structure. PMID:27410898

  15. Design of multiple-ply laminated composite tapered beams

    NASA Technical Reports Server (NTRS)

    Rodriguez, P.

    1993-01-01

    A study of a special case of symmetric laminated composite cantilever beams is presented. The approach models beams that are tapered both in depth and width and investigates the effect of the ply layup angle and the ply taper on bending and interlaminar shearing stresses. For the determination of stresses and deflections, the beam stiffness matrices are expressed as linear functions of the beam length. Using classical lamination theory (CLT) the stiffness matrices are determined and assembled at strategic locations along the length of the beam. They are then inverted and necessary stiffness parameters are obtained numerically and extracted for determination of design information at each location chosen. Several ply layup configurations are investigated, and design considerations are presented based on the findings. Finally, recommendations for the design of these beams are presented, and a means for anticipating the location of highest stresses is offered.

  16. Tapered fiber bundle couplers for high-power fiber amplifiers

    NASA Astrophysics Data System (ADS)

    Sliwinska, Dorota; Kaczmarek, Pawel; Abramski, Krzysztof M.

    2014-12-01

    In this work, we would like to demonstrate our results on performing (6+1)x1 tapered fiber bundle combiners using a trielectrode fiber splicing system. In our combiners we have used 9/80 μm (core/clad) diameter fibers as single-mode signal input ports. Using this fiber, instead of a conventional 9/125 μm single-mode fiber allowed us to reduce the taper ratio and therefore significantly increase the signal transmission. We have also performed power combiner which is based on the LMA fibers: input signal fiber 20/125μm and passive double clad fiber 25/300 μm at the output.

  17. Piezoelectric energy harvester having planform-tapered interdigitated beams

    DOEpatents

    Kellogg, Rick A.; Sumali, Hartono

    2011-05-24

    Embodiments of energy harvesters have a plurality of piezoelectric planform-tapered, interdigitated cantilevered beams anchored to a common frame. The plurality of beams can be arranged as two or more sets of beams with each set sharing a common sense mass affixed to their free ends. Each set thus defined being capable of motion independent of any other set of beams. Each beam can comprise a unimorph or bimorph piezoelectric configuration bonded to a conductive or non-conductive supporting layer and provided with electrical contacts to the active piezoelectric elements for collecting strain induced charge (i.e. energy). The beams are planform tapered along the entirety or a portion of their length thereby increasing the effective stress level and power output of each piezoelectric element, and are interdigitated by sets to increase the power output per unit volume of a harvester thus produced.

  18. Optimized tapered dipole nanoantenna as efficient energy harvester.

    PubMed

    El-Toukhy, Youssef M; Hussein, Mohamed; Hameed, Mohamed Farhat O; Heikal, A M; Abd-Elrazzak, M M; Obayya, S S A

    2016-07-11

    In this paper, a novel design of tapered dipole nanoantenna is introduced and numerically analyzed for energy harvesting applications. The proposed design consists of three steps tapered dipole nanoantenna with rectangular shape. Full systematic analysis is carried out where the antenna impedance, return loss, harvesting efficiency and field confinement are calculated using 3D finite element frequency domain method (3D-FEFD). The structure geometrical parameters are optimized using particle swarm algorithm (PSO) to improve the harvesting efficiency and reduce the return loss at wavelength of 500 nm. A harvesting efficiency of 55.3% is achieved which is higher than that of conventional dipole counterpart by 29%. This enhancement is attributed to the high field confinement in the dipole gap as a result of multiple tips created in the nanoantenna design. Furthermore, the antenna input impedance is tuned to match a wide range of fabricated diode based upon the multi-resonance characteristic of the proposed structure.

  19. Integrated polarizers based on tapered highly birefringent photonic crystal fibers.

    PubMed

    Romagnoli, Priscila; Biazoli, Claudecir R; Franco, Marcos A R; Cordeiro, Cristiano M B; de Matos, Christiano J S

    2014-07-28

    This paper proposes and demonstrates the creation of sections with a high polarization dependent loss (PDL) in a commercial highly birefringent (polarization maintaining) photonic crystal fiber (PCF), via tapering with pressure applied to the holes. The tapers had a 1-cm-long uniform section with a 66% scale reduction, in which the original microstructure aspect ratio was kept by the pressure application. The resulting waveguides show polarizing action across the entire tested wavelength range, 1510-1600 nm, with a peak PDL of 35.3 dB/cm (c.f. ~1 dB/cm for a typical commercial polarizing fiber). The resulting structure, as well as its production, is extremely simple, and enable a small section with a high PDL to be obtained in a polarization maintaining PCF, meaning that the polarization axes in the polarizing and polarization maintaining sections are automatically aligned. PMID:25089397

  20. Influence of Root Canal Tapering on Smear Layer Removal.

    PubMed

    Zarei, Mina; Javidi, Maryam; Afkhami, Farzaneh; Tanbakuchi, Behrad; Zadeh, Mohsen Movahed; Mohammadi, Marzieh Maghadam

    2016-04-01

    The purpose of the study presented here was to compare the influence of root canal taper on the efficacy of irrigants and chelating agents in smear layer removal. Eighty mesial roots of molar teeth were selected and prepared with rotary instruments. In group A, file 30/0.02 and in group B, file 30/0.4 were placed at working length and the smear layer was removed. In groups C and D, root canal preparation was the same as in groups A and B, respectively, except that the smear layer was not removed. The amount of the smear layer was quantified using a scanning electron microscope. Greater smear layer was detected in the apical portion of each group, whereas no significant difference was detected between groups in other portions. No statistical difference was found between canals with different tapers. PMID:27348950

  1. A method for testing railway wheel sets on a full-scale roller rig

    NASA Astrophysics Data System (ADS)

    Liu, Binbin; Bruni, Stefano

    2015-09-01

    Full-scale roller rigs for tests on a single axle enable the investigation of several dynamics and durability problems related with the design and operation of the railway rolling stock. In order to exploit the best potential of this test equipment, appropriate test procedures need to be defined, particularly in terms of actuators' references, to make sure that meaningful wheel -rail contact conditions can be reproduced. The aim of this paper is to propose a new methodology to define the forces to be generated by the actuators in the rig in order to best reproduce the behaviour of a wheel set and especially the wheel -rail contact forces in a running condition of interest as obtained either from multi-body system (MBS) simulation or from on-track measurements. The method is supported by the use of a mathematical model of the roller rig and uses an iterative correction scheme, comparing the time histories of the contact force components from the roller rig test as predicted by the mathematical model to a set of target contact force time histories. Two methods are introduced, the first one considering a standard arrangement of the roller rig, the second one assuming that a differential gear is introduced in the rig, allowing different rolling speeds of the two rollers. Results are presented showing that the deviation of the roller rig test results from the considered targets can be kept within low tolerances (1% approximately) as far as the vertical and lateral contact forces on both wheels are concerned. For the longitudinal forces, larger deviations are obtained except in the case where a differential gear is introduced.

  2. An investigation into the impact of magnesium stearate on powder feeding during roller compaction.

    PubMed

    Dawes, Jason; Gamble, John F; Greenwood, Richard; Robbins, Phil; Tobyn, Mike

    2012-01-01

    A systematic evaluation on the effect of magnesium stearate on the transmission of a placebo formulation from the hopper to the rolls during screw fed roller compaction has been carried out. It is demonstrated that, for a system with two 'knurled' rollers, addition of 0.5% w/w magnesium stearate can lead to a significant increase in ribbon mass throughput, with a consequential increase in roll gap, compared to an unlubricated formulation (manufactured at equivalent process conditions). However, this effect is reduced if one of the rollers is smooth. Roller compaction of a lubricated formulation using two smooth rollers was found to be ineffective due to a reduction in friction at the powder/roll interface, i.e. powder was not drawn through the rollers leading to a blockage in the feeding system. An increase in ribbon mass throughput could also be achieved if the equipment surfaces were pre-lubricated. However this increase was found to be temporary suggesting that the residual magnesium stearate layer was removed from the equipment surfaces. Powder sticking to the equipment surfaces, which is common during pharmaceutical manufacturing, was prevented if magnesium stearate was present either in the blend, or at the roll surface. It is further demonstrated that the influence of the hopper stirrer, which is primarily used to prevent bridge formation in the hopper and help draw powder more evenly into the auger chamber, can lead to further mixing of the formulation, and could therefore affect a change in the lubricity of the carefully blended input material.

  3. Comparative evaluation of apically extruded debris with V-Taper, ProTaper Next, and the Self-adjusting File systems

    PubMed Central

    Vyavahare, Nishant K.; Raghavendra, Srinidhi Surya; Desai, Niranjan N.

    2016-01-01

    Background: Complete cleaning of the root canal is the goal for ensuring success in endodontics. Removal of debris plays an important role in achieving this goal. In spite of advancements in instrument design, apical extrusion of debris remains a source of inflammation in the periradicular region. Aim: To comparatively evaluate the amount of apically extruded debris with V-Taper, ProTaper Next, and the self-adjusting File (SAF) system. Materials and Methods: Sixty-four extracted human mandibular teeth with straight root canals were taken. Access openings were done and working length determined. The samples were randomly divided into three groups: Group I - V-Taper files (n = 20), Group II - ProTaper Next (n = 20), Group III - SAF (n = 20). Biomechanical preparation was completed and the debris collected in vials to be quantitatively determined. The data obtained was statistically analyzed using ANOVA and post hoc Tukey's test. Results: All the specimens showed apical debris extrusion. SAF showed significantly less debris extrusion compared to V-Taper and ProTaper Next (P < 0.001). Among Groups I and II, ProTaper Next showed lesser debris extrusion as compared to V-Taper, but it was not significant (P = 0.124). Conclusion: The SAF showed least amount of apical debris extrusion when compared to newer rotary endodontic instruments. This indicates that the incidence of inter-treatment flare-ups due to debris extrusion would be less with the SAF. PMID:27217636

  4. Effect of tapered normal and interval training on performance of Standardbred pacers.

    PubMed

    Shearman, J P; Hamlin, M J; Hopkins, W G

    2002-07-01

    Human athletes taper or reduce their training load before a race to enhance performance, apparently because recovery from the effects of fatigue occurs faster than the loss of fitness from the reduced training. However, there appear to be no previous studies of tapering of equine athletes. Our aim in the present study was, therefore, to investigate the efficacy of tapering with Standardbred pacers. We determined the effect of repeated cycles of tapered training on performance of Standardbred pacers. After 8 weeks of jogging and 3 x 2 week cycles of pace work, 19 horses were randomised to a taper and a control group. The taper group completed 5 consecutive 2 week cycles, each incorporating a 7 day taper; some cycles included high-intensity interval training. The control group continued with 5 more cycles of pace work. All horses completed a 2400 m individual time trial after each cycle. Peak and mean speed of the taper group were faster than those of the control group in all cycles; the differences were clear-cut in all cycles for peak speed (overall 4.4%, 95% confidence interval 1.7 to 7.1%), but only in one of the interval-training cycles for mean speed (2.4%, 0.3 to 4.7%). Four horses in the taper group were injured during interval training. Repeated tapering produces a worthwhile enhancement of performance in Standardbreds, but the addition of interval training appears to increase the risk of injury. PMID:12117113

  5. The taper disaster--how could it happen?

    PubMed

    Morlock, Michael M

    2015-01-01

    Corrosion of metallic implants in contact with body fluids is unavoidable, especially at interfaces where movement occurs or in gaps. Corrosion became clinically relevant with the introduction of large modular metal-on-metal total hip joint articulations (MoM THA) early in the 21st century. This review attempts to summarise the scientific knowledge about taper problems available at the time of introduction of these bearings, why this "disaster" could happen. It is speculated that changes to the taper connection made in the 1990s to increase the range of motion with small heads (28 and 32 mm) reduced the mechanical strength of this connection, which did not matter for small heads. With the use of large and very large metal heads in MoM articulations, which have a larger lever arm and can generate high friction in unfavourable situations, suddenly the taper interface exhibited corrosion problems on a previously unknown scale. It is speculated that due to the higher mechanical loading with larger heads, the taper connection became less forgiving with respect to assembly conditions, contamination, manufacturing tolerances and other factors, which are yet not known. Since no major clinical problems had been reported before the introduction of these bearings and the pre-clinical testing was very successful, the disaster took its course. The patient-implant-surgeon system is a very complex intrinsically hazardous system. Pre-clinical testing addresses few and defined factors and such, good results cannot be directly transferred to the clinical reality. A controlled stepwise introduction of innovations is required. PMID:26044535

  6. Gas insulated transmission line having tapered particle trapping ring

    DOEpatents

    Cookson, Alan H.

    1982-01-01

    A gas-insulated transmission line includes an outer sheath, an inner conductor, insulating supports and an insulating gas. A particle-trapping ring is secured to each insulating support, and it is comprised of a central portion and two tapered end portions. The ends of the particle trapping ring have a smaller diameter than the central portion of the ring, so as to enable the use of the particle trapping ring in a curved transmission line.

  7. Numerical Simulation of Flow Past a Tapered Cylinder

    NASA Technical Reports Server (NTRS)

    Jespersen, Dennis; Levit, Creon

    1990-01-01

    We have computed the unsteady three-dimensional low Reynolds number flow past a tapered cylinder. The spanwise variation in natural shedding frequency results in interesting three-dimensional flow phenomena. Our computed hot-wire and spectral data are very similar to experimental results. The computation was done on the Connection Machine, a massively parallel computer, we highlight the capabilities of the Connection Machine, for computation and visualization of three-dimensional unsteady flow fields.

  8. Numerical simulation of flow past a tapered cylinder

    NASA Technical Reports Server (NTRS)

    Jespersen, Dennis C.; Levit, Creon

    1991-01-01

    The unsteady three-dimensional low Reynolds number flow past a tapered cylinder is computed. The spanwise variation in natural shedding frequency results in interesting three-dimensional flow phenomena. The computed hot-wire and spectral data are very similar to experimental results. The computation was done on the Connection Machine, a massively parallel computer; highlights of the capabilities of the Connection Machine for computation and visualization of three-dimensional unsteady flow fields are shown.

  9. Plasmonic sensors based on doubly-deposited tapered optical fibers.

    PubMed

    González-Cano, Agustín; Navarrete, María-Cruz; Esteban, Óscar; Díaz-Herrera, Natalia

    2014-03-10

    A review of the surface plasmon resonance (SPR) transducers based on tapered fibers that have been developed in the last years is presented. The devices have proved their good performance (specifically, in terms of sensitivity) and their versatility and they are a very good option to be considered as basis for any kind of chemical and biological sensor. The technology has now reached its maturity and here we summarize some of the characteristics of the devices produced.

  10. Plasmonic Sensors Based on Doubly-Deposited Tapered Optical Fibers

    PubMed Central

    González-Cano, Agustín; Navarrete, María-Cruz; Esteban, Óscar; Díaz-Herrera, Natalia

    2014-01-01

    A review of the surface plasmon resonance (SPR) transducers based on tapered fibers that have been developed in the last years is presented. The devices have proved their good performance (specifically, in terms of sensitivity) and their versatility and they are a very good option to be considered as basis for any kind of chemical and biological sensor. The technology has now reached its maturity and here we summarize some of the characteristics of the devices produced. PMID:24618726

  11. Development of high-power gyrotrons with gradually tapered cavity

    SciTech Connect

    Lei Chaojun; Yu Sheng; Niu Xinjian; Liu Yinghui; Li Hongfu; Li Xiang

    2012-12-15

    In high power gyrotrons, the parasitic modes coupled with the operating mode cannot be avoided in the beam-wave interaction. These parasitic modes will decrease the efficiency of the gyrotrons. The purity of the operating mode affected by different tapers should be carefully studied. The steady-state self-consistent nonlinear theory for gyrotron with gradually tapered cavity is developed in this paper. A steady-state calculation code including 'cold cavity' and 'hot cavity' is designed. By comparison, a time-domain model analysis of gyrotron operation is also studied by particle-in-cell (PIC). It is found that the tapers of gyrotron have different influences on the modes coupling between the operating mode and the parasitic modes. During the study, an example of 94 GHz gyrotron with pure operating mode TE{sub 03} has been designed. The purity of the operating mode in the optimized cavity is up to -77 dB, and in output waveguide of the cavity is up to -76 dB. At the same time, the beam-wave interaction in the designed cavity has been simulated, too. An output power of 120 kW, corresponding to 41.6% efficiency and an oscillation frequency of 94.099 GHz have been achieved with a 50 kV, 6 A helical electron beam at a guiding magnetic field of 3.5485 T. The results show that the power in spurious modes of the optimized cavity may be kept far below than that of the traditional tapered cavity.

  12. Collisional heating by nonthermal electrons in a tapered magnetic loop

    NASA Technical Reports Server (NTRS)

    Chandrashekar, S.; Emslie, A. Gordon

    1987-01-01

    The behavior of nonthermal electrons ejected into a tapered magnetic loop, under the action of both Coulomb collisional and magnetic field gradient forces is studied. An approximate analytic formula for the heating rate as a function of distance along the loop is developed, and found to be in good agreement with exact numerical solutions of the relevant equations. Such a formula is useful as a source term in many situations, such as hydrodynamic simulations of atmospheric response to flare energy input.

  13. The structural damping of composite beams with tapered boundaries

    NASA Astrophysics Data System (ADS)

    Coni, M.; Benchekchou, B.; White, R. G.

    1994-11-01

    Most metallic and composite structures of conventional construction are lightly damped. It is obviously advantageous, in terms of response to in-service dynamic loading, if damping can be increased with minimal weight addition. This report describes finite element analyses and complementary experiments carried out on composite, carbon fiber reinforced plastic, beams with tapered boundaries composed of layers of highly damped composite material. It is shown that modal damping of the structure may be significantly increased by this method.

  14. In-situ Tapering of Chalcogenide Fiber for Mid-infrared Supercontinuum Generation

    PubMed Central

    Rudy, Charles W.; Marandi, Alireza; Vodopyanov, Konstantin L.; Byer, Robert L.

    2013-01-01

    Supercontinuum generation (SCG) in a tapered chalcogenide fiber is desirable for broadening mid-infrared (or mid-IR, roughly the 2-20 μm wavelength range) frequency combs1, 2 for applications such as molecular fingerprinting, 3 trace gas detection, 4 laser-driven particle acceleration, 5 and x-ray production via high harmonic generation. 6 Achieving efficient SCG in a tapered optical fiber requires precise control of the group velocity dispersion (GVD) and the temporal properties of the optical pulses at the beginning of the fiber, 7 which depend strongly on the geometry of the taper. 8 Due to variations in the tapering setup and procedure for successive SCG experiments-such as fiber length, tapering environment temperature, or power coupled into the fiber, in-situ spectral monitoring of the SCG is necessary to optimize the output spectrum for a single experiment. In-situ fiber tapering for SCG consists of coupling the pump source through the fiber to be tapered to a spectral measurement device. The fiber is then tapered while the spectral measurement signal is observed in real-time. When the signal reaches its peak, the tapering is stopped. The in-situ tapering procedure allows for generation of a stable, octave-spanning, mid-IR frequency comb from the sub harmonic of a commercially available near-IR frequency comb. 9 This method lowers cost due to the reduction in time and materials required to fabricate an optimal taper with a waist length of only 2 mm. The in-situ tapering technique can be extended to optimizing microstructured optical fiber (MOF) for SCG10 or tuning of the passband of MOFs, 11 optimizing tapered fiber pairs for fused fiber couplers12 and wavelength division multiplexers (WDMs), 13 or modifying dispersion compensation for compression or stretching of optical pulses.14-16 PMID:23748947

  15. Coal grinding by roller grinding mills for pulverized coal injection in blast furnaces

    SciTech Connect

    Kasseck, K.; Salewski, G.

    1995-10-01

    Roller grinding mills are increasingly being used for producing the pulverized coal required for injection into blast furnaces, an accepted technology worldwide for lowering coke consumption in blast furnaces. Coal is currently being injected into blast furnaces at the rate of 80 to 200 kg/tonne of hot metal which results in a coke savings of 72 to 180 kg/tonne of hot metal. The pulverized coal for coal injection is produced in coal grinding and drying plants currently having a capacity from 15 to 240 tonnes/hr. The grinding plant with Loesche roller grinding mills at the Ilva steelworks, Taranto, Italy, that is described, illustrates design concepts and operation.

  16. High speed cylindrical roller bearing analysis, SKF computer program CYBEAN. Volume 2: User's manual

    NASA Technical Reports Server (NTRS)

    Kleckner, R. J.; Pirvics, J.

    1978-01-01

    The CYBEAN (Cylindrical Bearing Analysis) was created to detail radially loaded, aligned and misaligned cylindrical roller bearing performance under a variety of operating conditions. Emphasis was placed on detailing the effects of high speed, preload and system thermal coupling. Roller tilt, skew, radial, circumferential and axial displacement as well as flange contact were considered. Variable housing and flexible out-of-round outer ring geometries, and both steady state and time transient temperature calculations were enabled. The complete range of elastohydrodynamic contact considerations, employing full and partial film conditions were treated in the computation of raceway and flange contacts. Input and output architectures containing guidelines for use and a sample execution are detailed.

  17. Roller-Massager Application to the Quadriceps and Knee-Joint Range of Motion and Neuromuscular Efficiency During a Lunge

    PubMed Central

    Bradbury-Squires, David J.; Noftall, Jennifer C.; Sullivan, Kathleen M.; Behm, David G.; Power, Kevin E.; Button, Duane C.

    2015-01-01

    Context: Roller massagers are used as a recovery and rehabilitative tool to initiate muscle relaxation and improve range of motion (ROM) and muscular performance. However, research demonstrating such effects is lacking. Objective: To determine the effects of applying a roller massager for 20 and 60 seconds on knee-joint ROM and dynamic muscular performance. Design: Randomized controlled clinical trial. Setting: University laboratory. Patients or Other Participants: Ten recreationally active men (age = 26.6 ± 5.2 years, height = 175.3 ± 4.3 cm, mass = 84.4 ± 8.8 kg). Intervention(s): Participants performed 3 randomized experimental conditions separated by 24 to 48 hours. In condition 1 (5 repetitions of 20 seconds) and condition 2 (5 repetitions of 60 seconds), they applied a roller massager to the quadriceps muscles. Condition 3 served as a control condition in which participants sat quietly. Main Outcome Measure(s): Visual analog pain scale, electromyography (EMG) of the vastus lateralis (VL) and biceps femoris during roller massage and lunge, and knee-joint ROM. Results: We found no differences in pain between the 20-second and 60-second roller-massager conditions. During 60 seconds of roller massage, pain was 13.5% (5.7 ± 0.70) and 20.6% (6.2 ± 0.70) greater at 40 seconds and 60 seconds, respectively, than at 20 seconds (P < .05). During roller massage, VL and biceps femoris root mean square (RMS) EMG was 8% and 7%, respectively, of RMS EMG recorded during maximal voluntary isometric contraction. Knee-joint ROM was 10% and 16% greater in the 20-second and 60-second roller-massager conditions, respectively, than the control condition (P < .05). Finally, average lunge VL RMS EMG decreased as roller-massage time increased (P < .05). Conclusions: Roller massage was painful and induced muscle activity, but it increased knee-joint ROM and neuromuscular efficiency during a lunge. PMID:25415414

  18. Single-mode fiber linearly tapered planar waveguide tunable coupler

    NASA Astrophysics Data System (ADS)

    Das, Alok K.; Hussain, Anwar

    1997-09-01

    We developed a simple system of tunable fiber film coupler using a linearly tapered thin-film planar waveguide (PWG) evanescently coupled by a single-mode distributed fiber half-coupler. We investigate the characteristics of the coupler theoretically and experimentally taking into consideration the refractive index ( n f ) of nonuniform films, the magnitude of nonuniformity ( m ) of the films, and the source wavelength ( ). The thickness variation of the nonuniform film is along the direction of propagation of optical power. Tapered and plano concave thin films of a mix of oils as well as a plano concave poly(methyl methacrylate) film were fabricated to serve as nonuniform PWG s. Similar to single-mode fiber with a uniform thickness PWG coupler, such a coupler also provides light modulation with a change of n f . However, position shifting of a half-coupler in a tapered PWG structure along the direction of propagation exhibits the variation of fiber throughput power. This action serves as a simple system for a tunable fiber film coupler. Wavelength-dependent throughput fiber power for such a coupler also behaves as a filter. The center wavelength can be controlled by shifting the position of the half-coupler. A coupling fiber as a half-coupler can be used for efficient coupling. We performed a theoretical analysis of the structure using Marcuse s model and observed good agreement with the experimental results.

  19. Model-based optimization of tapered free-electron lasers

    NASA Astrophysics Data System (ADS)

    Mak, Alan; Curbis, Francesca; Werin, Sverker

    2015-04-01

    The energy extraction efficiency is a figure of merit for a free-electron laser (FEL). It can be enhanced by the technique of undulator tapering, which enables the sustained growth of radiation power beyond the initial saturation point. In the development of a single-pass x-ray FEL, it is important to exploit the full potential of this technique and optimize the taper profile aw(z ). Our approach to the optimization is based on the theoretical model by Kroll, Morton, and Rosenbluth, whereby the taper profile aw(z ) is not a predetermined function (such as linear or exponential) but is determined by the physics of a resonant particle. For further enhancement of the energy extraction efficiency, we propose a modification to the model, which involves manipulations of the resonant particle's phase. Using the numerical simulation code GENESIS, we apply our model-based optimization methods to a case of the future FEL at the MAX IV Laboratory (Lund, Sweden), as well as a case of the LCLS-II facility (Stanford, USA).

  20. Sinking and fit of abutment of locking taper implant system

    PubMed Central

    Moon, Seung-Jin; Kim, Hee-Jung; Son, Mee-Kyoung

    2009-01-01

    STATEMENT OF PROBLEM Unlike screw-retention type, fixture-abutment retention in Locking taper connection depends on frictional force so it has possibility of abutment to sink. PURPOSE In this study, Bicon® Implant System, one of the conical internal connection implant system, was used with applying loading force to the abutments connected to the fixture. Then the amount of sinking was measured. MATERIAL AND METHODS 10 Bicon® implant fixtures were used. First, the abutment was connected to the fixture with finger force. Then it was tapped with a mallet for 3 times and loads of 20 kg corresponding to masticatory force using loading application instrument were applied successively. The abutment state, slightly connected to the fixture without pressure was considered as a reference length, and every new abutment length was measured after each load's step was added. The amount of abutment sinking (mm) was gained by subtracting the length of abutment-fixture under each loading condition from reference length. RESULTS It was evident, that the amount of abutment sinking in Bicon® Implant System increased as loads were added. When loads of 20 kg were applied more than 5 - 7 times, sinking stopped at 0.45 ± 0.09 mm. CONCLUSION Even though locking taper connection type implant shows good adaption to occlusal force, it has potential for abutment sinking as loads are given. When locking taper connection type implant is used, satisfactory loads are recommended for precise abutment location. PMID:21165262

  1. Microbiological Seal of Two Types of Tapered Implant Connections.

    PubMed

    Peruzetto, Wheslley M; Martinez, Elizabeth F; Peruzzo, Daiane C; Joly, Júlio Cesar; Napimoga, Marcelo H

    2016-01-01

    Tapered implant connections have gained wide popularity for being more resistant to fatigue and for promoting a better seal against bacterial infiltration than conventional connections. The aim of this study was to evaluate the bacterial seal at the implant-abutment interface using two Morse taper implant models, by in vitro microbiological analysis. Eleven non-indexed and 11 indexed abutments were selected and connected to their respective implants with a 20 N torque, according to manufacturer's recommendation. Microbiological analysis was carried out using colonies of Escherichia coli transported directly from a culture dish to the prosthetic component. For control, one non-contaminated abutment-implant set from each group (negative control) and one contaminated implant with no abutment (positive control) were used. The specimens were immersed in BHI broth and maintained in an incubator at 37 °C for 14 days to assess the development of bacterial contamination. The results revealed that 36.4% (n=4) of the indexed components and 90.9% (n=10) of the non-indexed components allowed bacterial leakage, with significant difference between groups (p=0.0237). In conclusion, both tapered components failed to provide adequate sealing to bacterial leakage, although the indexed type components showed a superior seal compared with non-indexed components.

  2. A prospective evaluation of outcomes of two tapered implant systems.

    PubMed

    Andreasi Bassi, M; Lopez, M A; Confalone, L; Gaudio, R M; Lombardo, L; Lauritano, D

    2016-01-01

    The purpose of this prospective clinical study was to evaluate survival rate (SVR - i.e. fixtures still in place at the end of the observation period) and success rate (SCR - i.e. bone resorption around the implant neck) of two tapered implant systems. Both systems were equipped with a tapered connection, one requiring bone-level (BL) placement, while the other required soft-tissue-level (STL) placement. In the period between January 1996 and October 2011, 133 fixtures were inserted, 90 in females and 43 in males, with a mean age of 60±11 years. The mean post-surgical follow-up was 64±38 months. Several clinical parameters were evaluated as potential outcome conditioners. An SPSS program was used for statistical analysis and a Cox analysis was performed. The SVR was 100% since no fixtures were lost. SCR, expressed through the mean marginal bone loss, was 88%. No significant differences were found, for most of the variables investigated with the exception of bone grafting and implant type: STL implants showed a better clinical outcome than BL implants when bone grafting was performed simultaneously with implant placement. Tapered implants are reliable devices for oral rehabilitation of jaws. PMID:27469541

  3. Submicron particle manipulation using slotted tapered optical fibers

    NASA Astrophysics Data System (ADS)

    Daly, M.; Truong, V. G.; Nic Chormaic, S.

    2015-08-01

    The use of optical micro- and nanofibers has become commonplace in the areas of atom trapping using neutral atoms and, perhaps more relevantly, the optical trapping and propulsion of micro- and nanoscale particles. It has been shown that such fibers can be used to manipulate and trap silica and polystyrene particles in the 1-3 µm range using either the fundamental or higher order modes of the fibers, with the propulsion of smaller particle sizes also possible through the use of metallic and/or high index materials. We previously proposed using a focused ion beam nanostructured tapered optical fiber for improved atom trapping geometries; here, we present the details of how these nanostructured optical fibers can be used as a platform for submicron particle trapping. The optical fibers are tapered to approximately 1.2 µm waist diameters, using a custom-built, heat-and-pull fiber rig prior to processing using a focused ion beam. Slots of approximately 300 nm in width and 10-20 µm in length are milled clean though the waist regions of the tapered optical fibers. High fiber transmissions (> 80%) over a broad range of wavelengths (700-1100 nm) are observed. We present simulation results for the trapping of submicron particles and experimental results on the trapping of 200 nm particles. This work demonstrates even further the functionality of optical micro- and nanofibers as trapping devices across a range of regimes.

  4. A prospective evaluation of outcomes of two tapered implant systems.

    PubMed

    Andreasi Bassi, M; Lopez, M A; Confalone, L; Gaudio, R M; Lombardo, L; Lauritano, D

    2016-01-01

    The purpose of this prospective clinical study was to evaluate survival rate (SVR - i.e. fixtures still in place at the end of the observation period) and success rate (SCR - i.e. bone resorption around the implant neck) of two tapered implant systems. Both systems were equipped with a tapered connection, one requiring bone-level (BL) placement, while the other required soft-tissue-level (STL) placement. In the period between January 1996 and October 2011, 133 fixtures were inserted, 90 in females and 43 in males, with a mean age of 60±11 years. The mean post-surgical follow-up was 64±38 months. Several clinical parameters were evaluated as potential outcome conditioners. An SPSS program was used for statistical analysis and a Cox analysis was performed. The SVR was 100% since no fixtures were lost. SCR, expressed through the mean marginal bone loss, was 88%. No significant differences were found, for most of the variables investigated with the exception of bone grafting and implant type: STL implants showed a better clinical outcome than BL implants when bone grafting was performed simultaneously with implant placement. Tapered implants are reliable devices for oral rehabilitation of jaws.

  5. Magnetic field tunability of optical microfiber taper integrated with ferrofluid.

    PubMed

    Miao, Yinping; Wu, Jixuan; Lin, Wei; Zhang, Kailiang; Yuan, Yujie; Song, Binbin; Zhang, Hao; Liu, Bo; Yao, Jianquan

    2013-12-01

    Optical microfiber taper has unique propagation properties, which provides versatile waveguide structure to design the tunable photonic devices. In this paper, the S-tapered microfiber is fabricated by using simple fusion spicing. The spectral characteristics of microfiber taper integrated with ferrofluid under different magnetic-field intensities have been theoretically analyzed and experimentally demonstrated. The spectrum are both found to become highly magnetic-field-dependent. The results indicate the transmission and wavelength of the dips are adjustable by changing magnetic field intensity. The response of this device to the magnetic field intensity exhibits a Langvin function. Moreover, there is a linear relationship between the transmission loss and magnetic field intensity for a magnetic field intensity range of 25 to 200Oe, and the sensitivities as high as 0.13056dB/Oe and 0.056nm/Oe have been achieved, respectively. This suggests a potential application of this device as a tunable all-in-fiber photonic device, such as magneto-optic modulator, filter, and sensing element. PMID:24514542

  6. Double clad tapered fiber for high power applications.

    PubMed

    Filippov, V; Chamorovskii, Yu; Kerttula, J; Golant, K; Pessa, M; Okhotnikov, O G

    2008-02-01

    We report a novel type of active fiber - tapered double clad fiber suitable for pumping by low brightness sources with large beam parameter product of 50/300 mm x mrad. Ytterbium double clad all-silica fiber (core/1(st) clad/2(nd) clad diameters 27/834/890 mum, NA(core)=0.11, NA(clad)=0.21), tapered down by a factor 4.8 for a length of 10.5 m was drawn from a preform fabricated by plasma chemical technologies. At a moderate Yb-ion concentration and 1:31 core/cladding ratio, the tapered double clad fiber demonstrates 0.9 dB/m pump absorption at 976 nm and excellent lasing slope efficiency. An ytterbium fiber laser with 84 W of output power and 92% slope efficiency, a 74 W superfluorescent source with 85% slope efficiency and amplifiers operating both in CW and pulsed regimes have been realized. All devices demonstrated robust single mode operation with a beam quality factor of M(2)=1.07. PMID:18542272

  7. Microbiological Seal of Two Types of Tapered Implant Connections.

    PubMed

    Peruzetto, Wheslley M; Martinez, Elizabeth F; Peruzzo, Daiane C; Joly, Júlio Cesar; Napimoga, Marcelo H

    2016-01-01

    Tapered implant connections have gained wide popularity for being more resistant to fatigue and for promoting a better seal against bacterial infiltration than conventional connections. The aim of this study was to evaluate the bacterial seal at the implant-abutment interface using two Morse taper implant models, by in vitro microbiological analysis. Eleven non-indexed and 11 indexed abutments were selected and connected to their respective implants with a 20 N torque, according to manufacturer's recommendation. Microbiological analysis was carried out using colonies of Escherichia coli transported directly from a culture dish to the prosthetic component. For control, one non-contaminated abutment-implant set from each group (negative control) and one contaminated implant with no abutment (positive control) were used. The specimens were immersed in BHI broth and maintained in an incubator at 37 °C for 14 days to assess the development of bacterial contamination. The results revealed that 36.4% (n=4) of the indexed components and 90.9% (n=10) of the non-indexed components allowed bacterial leakage, with significant difference between groups (p=0.0237). In conclusion, both tapered components failed to provide adequate sealing to bacterial leakage, although the indexed type components showed a superior seal compared with non-indexed components. PMID:27224559

  8. Computationally generated velocity taper for efficiency enhancement in a coupled-cavity traveling-wave tube

    NASA Technical Reports Server (NTRS)

    Wilson, Jeffrey D.

    1989-01-01

    A computational routine has been created to generate velocity tapers for efficiency enhancement in coupled-cavity TWTs. Programmed into the NASA multidimensional large-signal coupled-cavity TWT computer code, the routine generates the gradually decreasing cavity periods required to maintain a prescribed relationship between the circuit phase velocity and the electron-bunch velocity. Computational results for several computer-generated tapers are compared to those for an existing coupled-cavity TWT with a three-step taper. Guidelines are developed for prescribing the bunch-phase profile to produce a taper for efficiency. The resulting taper provides a calculated RF efficiency 45 percent higher than the step taper at center frequency and at least 37 percent higher over the bandwidth.

  9. Taper junction failure in large-diameter metal-on-metal bearings

    PubMed Central

    Langton, D. J.; Sidaginamale, R.; Lord, J. K.; Nargol, A. V. F.; Joyce, T. J.

    2012-01-01

    Objectives An ongoing prospective study to investigate failing metal-on-metal hip prostheses was commenced at our centre in 2008. We report on the results of the analysis of the first consecutive 126 failed mated total hip prostheses from a single manufacturer. Methods Analysis was carried out using highly accurate coordinate measuring to calculate volumetric and linear rates of the articular bearing surfaces and also the surfaces of the taper junctions. The relationship between taper wear rates and a number of variables, including bearing diameter and orientation of the acetabular component, was investigated. Results The measured rates of wear and distribution of material loss from the taper surfaces appeared to show that the primary factor leading to taper failure is the increased lever arm acting on this junction in contemporary large-diameter metal-on-metal hip replacements. Conclusions Our analysis suggests that varus stems, laterally engaging taper systems and larger head diameters all contribute to taper failure. PMID:23610672

  10. Key findings from studies of methotrexate tapering and withdrawal in rheumatoid arthritis.

    PubMed

    Subesinghe, Sujith; Scott, Ian C

    2015-01-01

    Methotrexate is the dominant initial drug in the management of rheumatoid arthritis (RA). Despite its widespread use, methotrexate is associated with a number of adverse effects. Tapering its dose to the minimal amount required to maintain RA remission is, therefore, an important clinical goal. While the complete withdrawal of disease-modifying anti-rheumatic drugs is associated with a definite risk of a disease flare, it is unclear as to what the risk is specific to methotrexate withdrawal and whether this can be minimized by gradual dose reduction (termed 'tapering'). This review examines studies of methotrexate tapering and withdrawal on RA outcomes. It covers three scenarios: tapering/withdrawing methotrexate monotherapy; tapering/withdrawing methotrexate as part of a 'step-down' combination disease-modifying anti-rheumatic drug regimen; and tapering/withdrawing methotrexate when it is being co-prescribed with biologic agents. PMID:26289226

  11. Strain energy release rate analysis of delamination in a tapered laminate subjected to tension load

    NASA Technical Reports Server (NTRS)

    Salpekar, S. A.; Raju, I. S.; O'Brien, T. K.

    1988-01-01

    Finite element method was used to analyze a tapered glass/epoxy composite laminate subjected to a tension load, in order to determine the interlaminar stress distributions the strain-energy release rate for the delamination growth that may occur due to ply drops. In a laminate having a typical configuration of a helicopter hub, the (+/- 45)3 plies were dropped in three distinct steps, each 20-ply thickness apart, with the resulting taper angle of 5.71 deg. Delaminations were assumed to initiate at the bottom of the taper on the -45/+45 interface, and the delamination growth was simulated along the taper and into the thin region. The results of the analysis indicated that a delamination initiating at the end of the taper will grow unstably along the taper and the thin laminate simultaneously.

  12. Key findings from studies of methotrexate tapering and withdrawal in rheumatoid arthritis.

    PubMed

    Subesinghe, Sujith; Scott, Ian C

    2015-01-01

    Methotrexate is the dominant initial drug in the management of rheumatoid arthritis (RA). Despite its widespread use, methotrexate is associated with a number of adverse effects. Tapering its dose to the minimal amount required to maintain RA remission is, therefore, an important clinical goal. While the complete withdrawal of disease-modifying anti-rheumatic drugs is associated with a definite risk of a disease flare, it is unclear as to what the risk is specific to methotrexate withdrawal and whether this can be minimized by gradual dose reduction (termed 'tapering'). This review examines studies of methotrexate tapering and withdrawal on RA outcomes. It covers three scenarios: tapering/withdrawing methotrexate monotherapy; tapering/withdrawing methotrexate as part of a 'step-down' combination disease-modifying anti-rheumatic drug regimen; and tapering/withdrawing methotrexate when it is being co-prescribed with biologic agents.

  13. Coupled-Cavity Traveling-Wave Tube Has Phase-Adjusted Taper

    NASA Technical Reports Server (NTRS)

    Wilson, Jeffrey D.

    1992-01-01

    In structure of improved coupled-cavity traveling-wave tube amplifier, lengths of cavities chosen according to computer-generated, nonlinear taper to increase efficiency of conversion of power from electron beam to microwave. Design calls for "phase-adjusted taper," calculated so phase of electron bunches with respect to phase of microwave changes gradually from value conducive to formation of strong bunches to value conducive to strong transfer of power to microwave at output of taper. Phase-adjusted taper significantly increases power capability of microwave transmission, enabling satellite-communication systems to have higher data-transmission rates.

  14. Multimode Brillouin spectrum in a long tapered birefringent photonic crystal fiber.

    PubMed

    Tchahame, Joël Cabrel; Beugnot, Jean-Charles; Kudlinski, Alexandre; Sylvestre, Thibaut

    2015-09-15

    We investigate the stimulated Brillouin scattering (SBS) in a long tapered birefringent solid-core photonic crystal fiber (PCF) and compare our results with a similar but untapered PCF. It is shown that the taper generates a broadband and multipeaked Brillouin spectrum, while significantly increasing the threshold power. Furthermore, we observe that the strong fiber birefringence gives rise to a frequency shift of the Brillouin spectrum which increases along the fiber. Numerical simulations are also presented to account for the taper effect and the birefringence. Our findings open a new means to control or inhibit the SBS by tapering photonic crystal fibers. PMID:26371916

  15. Ultrathin fiber-taper coupling with nitrogen vacancy centers in nanodiamonds at cryogenic temperatures

    NASA Astrophysics Data System (ADS)

    Fujiwara, Masazumi; Zhao, Hong-Quan; Noda, Tetsuya; Ikeda, Kazuhiro; Sumiya, Hitoshi; Takeuchi, Shigeki

    2016-03-01

    We demonstrate successful cooling of ultrathin fiber tapers and their coupling with nitrogen vacancy (NV) centers in nanodiamonds at cryogenic temperatures. Nanodiamonds containing multiple NV centers are deposited on ultrathin fiber tapers with diameters ranging from 450-500 nm. The fiber tapers were successfully cooled down to 9 K with our special fiber mount and an optimization of cooling speed. The fluorescence coupled with the fiber tapers showed characteristic sharp zero-phonon lines of neutral and negatively charged NV centers. The present demonstration is important for the future NV-based quantum information devices and sensitive nanoscale cryogenic magnetometry.

  16. The effects of blood and fat on Morse taper disassembly forces.

    PubMed

    Lavernia, Carlos J; Baerga, Luis; Barrack, Robert L; Tozakoglou, Evangelos; Cook, Stephen D; Lata, Loren; Rossi, Mark D

    2009-04-01

    Biological debris between modular components using Morse tapers in hip arthroplasty can lead to weakening of the implant construct. We conducted a study to determine the effect of blood and fat within the taper interface. Tapers were divided into groups 1 (clean), 2 (surface covered with blood and fat), and 3 (blood and fat wiped off). Each taper was impacted and disassembled 5 times. There was a difference in mean disassembly force between pulls within group 2. Thus, blood and fat contamination can have a significant effect on the potential for disassembly.

  17. Efficiency enhancement of coupled-cavity TWT's through cavity resonance tapering

    NASA Technical Reports Server (NTRS)

    Connolly, D. J.

    1979-01-01

    The paper examines efficiency enhancement of coupled-cavity traveling-wave tube (TWT) through cavity resonance tapering. Beam-wave resynchronization through circuit velocity reduction is used for TWT efficiency enhancement, with circuit velocity reduction in coupled cavity TWT's accomplished through period tapering. However, the amount of the latter is limited by the stability considerations, so that beyond a critical value of velocity reduction, the tube may be subject to zero drive oscillations originating in the velocity taper region. The coupled-cavity resonance tapering allows the velocity reduction to continue beyond the limit of stable period tapering, and it is accomplished by a gradual reduction in the cavity resonance frequency, with the period and the circuit bandwidth unchanged. The advantages of cavity resonance tapering vs period tapering are discussed, and test data are presented with the results of large-signal computer calculations. It is shown that cavity resonance tapering can produce efficiencies as period tapering without incurring the same risk of lower band-edge oscillations.

  18. Simple Expressions for the Design of Linear Tapers in Overmoded Corrugated Waveguides

    PubMed Central

    Schaub, S. C.; Shapiro, M. A.; Temkin, R. J.

    2016-01-01

    Simple analytical formulae are presented for the design of linear tapers with very low mode conversion loss in overmoded corrugated waveguides. For tapers from waveguide radius a2 to a1, with a1 < a2, the optimal length of the taper is 3.198a1a2/λ. Here, λ is the wavelength of radiation. The fractional loss of the HE11 mode in an optimized taper is 0.0293(a2−a1)4∕a12a22. These formulae are accurate when a2 ≲ 2a1. Slightly more complex formulae, accurate for a2 ≤ 4a1, are also presented in this paper. The loss in an overmoded corrugated linear taper is less than 1 % when a2 ≤ 2.12a1 and less than 0.1 % when a2 ≤ 1.53a1. The present analytic results have been benchmarked against a rigorous mode matching code and have been found to be very accurate. The results for linear tapers are compared with the analogous expressions for parabolic tapers. Parabolic tapers may provide lower loss, but linear tapers with moderate values of a2/a1 may be attractive because of their simplicity of fabrication. PMID:27053963

  19. Fundamental mode evolution in long, large-core (>100 μm) adiabatic tapers

    NASA Astrophysics Data System (ADS)

    Kerttula, Juho; Filippov, Valery; Chamorovskii, Yuri; Ustimchik, Vasily; Okhotnikov, Oleg G.

    2013-03-01

    We have experimentally investigated fundamental mode propagation in few-meter-long adiabatic step-index tapers with high numerical aperture, core diameter up to 117μm (V=38), and tapering ratio up to 18. We confirmed single fundamental mode guiding in tapers with uniform core index profile by several experiments. We observed an annular near field distribution and degraded beam quality for large output core diameters, found to occur due to intrinsic mechanical stress in the fibers. We expect that eliminating the stress would prevent the mode deformation and allow constructing single-mode, diffraction-limited tapered large-mode-area amplifiers with a good beam shape.

  20. Efficiency and Spectrum Enhancement in a Tapered Free-Electron Laser Amplifier

    SciTech Connect

    Wang, X. J.; Harder, D.; Murphy, J. B.; Qian, H.; Shen, Y.; Yang, X.; Freund, H. P.; Miner, W. H. Jr.

    2009-10-09

    We report the first experimental characterization of efficiency and spectrum enhancement in a laser-seeded free-electron laser using a tapered undulator. Output and spectra in the fundamental and third harmonic were measured versus distance for uniform and tapered undulators. With a 4% field taper over 3 m, a 300% (50%) increase in the fundamental (third harmonic) output was observed. A significant improvement in the spectra with the elimination of sidebands was observed using a tapered undulator. The experiment is in good agreement with predictions using the MEDUSA simulation code.

  1. Efficiency and spectrum enhancement in a tapered free-electron laser amplifier.

    PubMed

    Wang, X J; Freund, H P; Harder, D; Miner, W H; Murphy, J B; Qian, H; Shen, Y; Yang, X

    2009-10-01

    We report the first experimental characterization of efficiency and spectrum enhancement in a laser-seeded free-electron laser using a tapered undulator. Output and spectra in the fundamental and third harmonic were measured versus distance for uniform and tapered undulators. With a 4% field taper over 3 m, a 300% (50%) increase in the fundamental (third harmonic) output was observed. A significant improvement in the spectra with the elimination of sidebands was observed using a tapered undulator. The experiment is in good agreement with predictions using the MEDUSA simulation code. PMID:19905644

  2. Characterization of arbitrary fiber taper profiles with optical microscopy and image processing algorithms

    NASA Astrophysics Data System (ADS)

    Farias, Heric D.; Sebem, Renan; Paterno, Aleksander S.

    2014-08-01

    This work reports results from the development of a software to process the parameters involved in the characterization of fiber taper profiles, while using optical microscopy, a high-definition camera and a high- precision translation stage as the moveable base on which the taper is positioned. In addition to this procedure, image processing algorithms were customized to process the acquired images. With edge detection algorithms in the stitched image, one would be able to characterize the given taper radius curve that represents the taper profile when the camera has a sufficient resolution. As a consequence, the proposed fiber taper characterization procedure is a first step towards a high-resolution characterization of fiber taper diameters with arbitrary profiles, specially this case, in which tapers are fabricated with the stepwise technique that allows the production of non- biconical profiles. The parameters of the stitched images depends on the used microscope objective and the length of the characterized tapers. A non-biconical arbitrary taper is measured as an example for the illustration of the developed software and procedure.

  3. Multicolor upconversion emissions in Tm 3+/Er3+ codoped tellurite photonic microwire between silica fiber tapers.

    PubMed

    Chen, Nan-Kuang; Kuan, Pei-Wen; Zhang, Junjie; Zhang, Liyan; Hu, Lili; Lin, Chinlon; Tong, Limin

    2010-12-01

    We report multicolor upconversion emissions including the blue-violet, green, and red lights in a Tm 3+/Er3+codoped tellurite glass photonic microwire between two silica fiber tapers. A silica fiber is tapered until its evanescent field is exposed and then angled-cleaved at the tapered center to divide the tapered fibers into two parts. A tellurite glass is melted by a gas flame to cluster into a sphere at the tip of one tapered fiber. The other angled-cleaved tapered fiber is blended into the melted tellurite glass. When the tellurite glass is melted, the two silica fiber tapers are simultaneously moving outwards to draw the tellurite glass into a microwire in between. The advantage of angled-cleaving on fiber tapers is to avoid cavity resonances in high index photonic microwire. Thus, the broadband white light can be transmitted between silica fibers and a special optical property like high intensity upconversion emission can be achieved. A cw 1064 nm Nd:YAG laser light is launched into the Tm 3+/Er3+ codoped tellurite microwire through a silica fiber taper to generate the multicolor upconversion emissions, including the blue-violet, green, and red lights, simultaneously. PMID:21164907

  4. A study on the fabrication of main scale of linear encoder using continuous roller imprint method

    NASA Astrophysics Data System (ADS)

    Fan, Shanjin; Shi, Yongsheng; Yin, Lei; Feng, Long; Liu, Hongzhong

    2013-10-01

    Linear encoder composed of main and index scales has an extensive application in the field of modern precision measurement. The main scale is the key component of linear encoder as measuring basis. In this article, the continuous roller imprint technology is applied to the manufacturing of the main scale, this method can realize the high efficiency and low cost manufacturing of the ultra-long main scale. By means of the plastic deformation of the soft metal film substrate, the grating microstructure on the surface of the cylinder mold is replicated to the soft metal film substrate directly. Through the high precision control of continuous rotational motion of the mold, ultra-long high precision grating microstructure is obtained. This paper mainly discusses the manufacturing process of the high precision cylinder mold and the effects of the roller imprint pressure and roller rotation speed on the imprint replication quality. The above process parameters were optimized to manufacture the high quality main scale. At last, the reading test of a linear encoder contains the main scale made by the above method was conducted to evaluate its measurement accuracy, the result demonstrated the feasibility of the continuous roller imprint method.

  5. Design study of a continuously variable roller cone traction CVT for electric vehicles

    NASA Technical Reports Server (NTRS)

    Mccoin, D. K.; Walker, R. D.

    1980-01-01

    Continuously variable ratio transmissions (CVT) featuring cone and roller traction elements and computerized controls are studied. The CVT meets or exceeds all requirements set forth in the design criteria. Further, a scalability analysis indicates the basic concept is applicable to lower and higher power units, with upward scaling for increased power being more readily accomplished.

  6. The Dynamics of Plant Closings: An Extended Emotional Roller Coaster Ride.

    ERIC Educational Resources Information Center

    Hurst, Joe B.; Shepard, John W.

    1986-01-01

    Millions of United States' workers are unemployed, many of them dislocated from their jobs and careers by extended layoffs, drastic manpower reductions, and plant closings. Describes a model of the emotional roller coaster ride taken by employees displaced by a plant closing and suggests approaches to helping them and their families. (Author/ABB)

  7. "Roller coaster maneuver via lateral orbital approach" for reduction of isolated zygomatic arch fractures.

    PubMed

    Pilanci, Ozgur; Basaran, Karaca; Datli, Asli; Kuvat, Samet Vasfi

    2013-11-01

    Numerous techniques have been reported for the reduction of zygomatic arch fractures. In this article, we aimed to describe a technique we named as "roller coaster maneuver via lateral orbital approach" to closed reduction of the isolated-type zygomatic arch fractures. Surgical outcomes of 14 patients treated with this method were outlined. PMID:24220411

  8. The Comfortable Roller Coaster--on the Shape of Tracks with a Constant Normal Force

    ERIC Educational Resources Information Center

    Nordmark, Arne B.; Essen, Hanno

    2010-01-01

    A particle that moves along a smooth track in a vertical plane is influenced by two forces: gravity and normal force. The force experienced by roller coaster riders is the normal force, so a natural question to ask is, what shape of the track gives a normal force of constant magnitude? Here we solve this problem. It turns out that the solution is…

  9. One City, Two Worlds, and Yet...: New York from "Roller Skates" to "Stevie."

    ERIC Educational Resources Information Center

    Hendrickson, Linnea

    1998-01-01

    Explores Ruth Sawyer's "Roller Skates" and John Steptoe's "Stevie"--two very different works linked by common themes and settings. Concludes that these works portray children exploring the variety and richness of life in New York City of the 1890s and of the 1960s, and that both emphasize the importance of love, family, and reaching out to others.…

  10. High speed cylindrical roller bearing analysis. SKF computer program CYBEAN. Volume 2: User's manual

    NASA Technical Reports Server (NTRS)

    Dyba, G. J.; Kleckner, R. J.

    1981-01-01

    CYBEAN (CYlindrical BEaring ANalysis) was created to detail radially loaded, aligned and misaligned cylindrical roller bearing performance under a variety of operating conditions. Emphasis was placed on detailing the effects of high speed, preload and system thermal coupling. Roller tilt, skew, radial, circumferential and axial displacement as well as flange contact were considered. Variable housing and flexible out-of-round outer ring geometries, and both steady state and time transient temperature calculations were enabled. The complete range of elastohydrodynamic contact considerations, employing full and partial film conditions were treated in the computation of raceway and flange contacts. The practical and correct implementation of CYBEAN is discussed. The capability to execute the program at four different levels of complexity was included. In addition, the program was updated to properly direct roller-to-raceway contact load vectors automatically in those cases where roller or ring profiles have small radii of curvature. Input and output architectures containing guidelines for use and two sample executions are detailed.

  11. Spherical roller bearing analysis. SKF computer program SPHERBEAN. Volume 2: User's manual

    NASA Technical Reports Server (NTRS)

    Kleckner, R. J.; Dyba, G. J.

    1980-01-01

    The user's guide for the SPHERBEAN computer program for prediction of the thermomechanical performance characteristics of high speed lubricated double row spherical roller bearings is presented. The material presented is structured to guide the user in the practical and correct implementation of SPHERBEAN. Input and output, guidelines for program use, and sample executions are detailed.

  12. Daylighting performance evaluation of a bottom-up motorized roller shade

    SciTech Connect

    Kapsis, K.; Athienitis, A.K.; Zmeureanu, R.G.; Tzempelikos, A.

    2010-12-15

    This paper presents an experimental and simulation study for quantifying the daylighting performance of bottom-up roller shades installed in office spaces. The bottom-up shade is a motorized roller shade that opens from top to bottom operating in the opposite direction of a conventional roller shade, so as to cover the bottom part of the window, while allowing daylight to enter from the top part of the window, reaching deeper into the room. A daylighting simulation model, validated with full-scale experiments, was developed in order to establish correlations between the shade position, outdoor illuminance and work plane illuminance for different outdoor conditions. Then, a shading control algorithm was developed for application in any location and orientation. The validated model was employed for a sensitivity analysis of the impact of shade optical properties and control on the potential energy savings due to the use of daylighting. The results showed that Daylight Autonomy for the bottom-up shade is 8-58% higher compared to a conventional roller shade, with a difference of 46% further away from the facade, where the use of electric lighting is needed most of the time. The potential reduction in energy consumption for lighting is 21-41%. (author)

  13. High Speed Cylindrical Roller Bearing Analysis, SKF Computer Program CYBEAN. Volume 1: Analysis

    NASA Technical Reports Server (NTRS)

    Kleckner, R. J.; Pirvics, J.

    1978-01-01

    The CYBEAN (CYlindrical BEaring ANalysis) program was created to detail radially loaded, aligned and misaligned Cylindrical roller bearing performance under a variety of operating conditions. The models and associated mathematics used within CYBEAN are described. The user is referred to the material for formulation assumptions and algorithm detail.

  14. New steels and methods for induction hardening of bearing rings and rollers

    SciTech Connect

    Ouchakov, B.K.; Shepeljakovsky, K.Z.

    1998-12-31

    The new method of through-surface hardening (TSH) of bearing rings and rollers was developed and used in Russia and former USSR. The principles of the method include the use of special steels of low or controlled hardenability, through-the-section induction of furnace heating and intense quenching of the parts by water stream in special devices. Due to the low hardenability of applied steels, the bearing rings and rollers have high-strength martensitic surface layer, combined with a core strengthened with a troostite and sorbite structure. High compressive residual stresses are formed in the martensitic surface layers. For a long time TSH has been successfully used for inner rings of bearings for railway car boxes, large rings and rollers of bearings for cement furnaces and rolling mills. Recently TSH was used for hollow rollers of railway bearings. For bearing rings made of SAE 52100 type high-carbon, chromium-alloyed steel a new method of low-deformation hardening was developed. The method is based on self-calibration of the rings during the quenching process and is intended for through hardening by induction heating and quenching by rapidly moved water stream.

  15. The Roller-Coaster of Experiences: Becoming the Parent of a Deaf Child

    ERIC Educational Resources Information Center

    Bosteels, Sigrid; Van Hove, Geert; Vandenbroeck, Michel

    2012-01-01

    When early testing indicates a hearing loss, parents find themselves on a roller-coaster of experiences leaving little time or space for reflection. This study is based on interviews with families in the Flemish region of Belgium, one of the earliest in the world to introduce universal neonatal screening for hearing loss. Starting from a…

  16. Acceleration in One, Two, and Three Dimensions in Launched Roller Coasters

    ERIC Educational Resources Information Center

    Pendrill, Ann-Marie

    2008-01-01

    During a roller coaster ride, the body experiences acceleration in three dimensions. An accelerometer can measure and provide a graph of the forces on the body during different parts of a ride. To couple the experience of the body to pictures of the ride and an analysis of data can contribute to a deeper understanding of Newton's laws. This…

  17. Rolling Contact Fatigue Life of Steel Rollers Treated by Cavitation Peening and Shot Peening

    NASA Astrophysics Data System (ADS)

    Seki, Masanori; Soyama, Hitoshi; Kobayashi, Yuji; Gowa, Daisuke; Fujii, Masahiro

    The purpose of this study is to investigate the influence of peening on the rolling contact fatigue (RCF) life of steel rollers. First, steel rollers were treated by three types of peenings to ensure the same surface roughness of peened rollers. One is the cavitation peening (CP) used a cavitating jet in water with an injection pressure of 30 MPa, and the others are the fine particle peening (FPP) with a shot diameter of 0.1 mm and the normal shot peening (NSP) with a shot diameter of 0.3 mm. The surface hardness and the surface compressive residual stress of the steel rollers were increased by all the peenings. In particular, they were most increased by the FPP. On the other hand, the work-hardened depth due to the CP and the NSP was larger than that due to the FPP. As a result of the RCF tests, the RCF lives of the steel rollers were improved by all the peenings, and they were most improved by the NSP. Judging from the pmax - N curves and the [A(σy/√3 HV)]max - N curves, the improvement in RCF lives due to the FPP depended heavily on the increase in surface hardness due to that, and the effects of the CP and the NSP on the RCF were equivalent under the same surface roughness and the same surface hardness. It follows from these that the surface treatment condition should be selected according to the rolling contact conditions and the failure modes of machine elements.

  18. Knee joint position sense of roller hockey players: a comparative study.

    PubMed

    Venâncio, João; Lopes, Diogo; Lourenço, Joaquim; Ribeiro, Fernando

    2016-06-01

    This study aimed to compare knee joint position sense of roller hockey players with an age-matched group of non-athletes. Forty-three male participants voluntarily participated in this cross-sectional study: 21 roller hockey players (mean age: 23.2 ± 4.2 years old, mean weight: 81.8 ± 9.8 kg, mean height: 180.5 ± 4.1 cm) and 22 age-matched non-athletes (mean age: 23.7 ± 3.9 years old, mean weight: 85.0 ± 6.2 kg, mean height: 181.5 ± 5.0 cm). Knee joint position sense of the dominant limb was evaluated using a technique of open-kinetic chain and active knee positioning. Joint position sense was reported using absolute, relative and variable angular errors. The main results indicated that the group of roller hockey players showed significantly lower absolute (2.4 ± 1.2º vs. 6.5 ± 3.2º, p ≤ 0.001) and relative (1.7 ± 2.1º vs. 5.8 ± 4.4º, p ≤ 0.001) angular errors in comparison with the non-athletes group. In conclusion, the results from this present study suggest that proprioceptive acuity, assessed by measuring joint position sense, is increased in roller hockey players. The enhanced proprioception of the roller hockey players could contribute to injury prevention and improved performance during sporting activities. PMID:27111126

  19. Nest ecology of blood parasites in the European roller and its ectoparasitic carnid fly.

    PubMed

    Václav, Radovan; Betáková, Tatiana; Švančarová, Petra; Pérez-Serrano, Jorge; Criado-Fornelio, Ángel; Škorvanová, Lucia; Valera, Francisco

    2016-06-01

    Haemosporidian parasites are considered the most important vector-borne parasites. However, vector identity and ecology is unknown for most such host-vector-parasite systems. In this study, we employ microscopic and molecular analyses to examine haemosporidian prevalence in a migratory, cavity-nesting bird, European roller Coracias garrulus, and its nidicolous blood-feeding ectoparasite Carnus hemapterus. This system is unique in that the ectoparasite is confined to a near-closed environment, in contrast to the free-wandering system of haematophagous dipterans such as mosquitoes. Blood film analysis confirms previous works in that Haemoproteus parasites are widely prevalent in adult rollers and belong to a single species, Haemoproteus coraciae. Leucocytozoon sp. and Trypanosoma sp. also are detected in adult rollers at low intensities with this technique. By means of molecular analysis, we report for the first time Plasmodium sp. presence in C. garrulus. Based on PCR results, Plasmodium parasites are relatively less prevalent than Haemoproteus parasites (20% vs. 31%) in rollers. In contrast, haemosporidian prevalences show the opposite trend for Carnus flies: Plasmodium sp. occurrence (62%) clearly predominates over that of Haemoproteus sp. (5%). A comparison between roller and Carnus samples reveals a significantly higher prevalence of Plasmodium sp. in Carnus samples. Insect survey and phylogenetic analysis suggest Culicoides flies as Haemoproteus sp. vectors, which appear to readily transmit the parasite in southern Spain. This study does not find support for Carnus flies to serve as biological or mechanical vectors of haemosporidians. In spite of this, nidicolous blood-feeding ectoparasites, such as carnid flies, appear as a suitable model for studies on the occurrence and temporal dynamics of avian haemosporidians such as Plasmodium sp. present at low intensities. PMID:26993083

  20. Morphometric examination of straight, tapered titanium stems: a retrieval study.

    PubMed

    Böhm, G; Lintner, F; Auterith, A; Lester, D K; Zweymüller, K A

    2001-12-01

    Cementless straight, tapered rectangular cross section titanium stems have been used by the senior author since 1979. Thirty-four stems retrieved postmortem, after between 10 days and 15.2 years in situ, were studied morphometrically and histologically. Nineteen stems were first generation (1979-1986), with an incomplete sagittal taper and a mean surface roughness of 1 microm (Ra 1.23 +/- 0.3 microm); 15 stems were second generation after 1986, with a full biplane taper and a mean surface roughness of 4 microm (Ra 4.14 +/- 0.36 microm). Implant surface bony coverage was determined morphometrically in 10 segments of the stems, and expressed as a bone implant contact index. Histologically, there were no differences between implants with different levels of roughness. Morphometrically, the first-generation stems showed significant differences in coverage (distal > proximal); second-generation stems had a more uniform pattern. Stems retrieved early after arthroplasty had a mean bone implant contact index of 10%. The mean bone implant contact index showed attainment of maximum coverage by 5 years after arthroplasty, without additional apposition or loss thereafter. Patients younger than 65 years at arthroplasty had similar bone implant contact indices to patients 65 years or older; coverage in the six patients 80 years of age at retrieval did not differ from the rates in the other patients. Morphometry was able to provide objective evidence of design change effects. No differences in coverage were found in terms of times in situ, patient age at arthroplasty and at retrieval, and degree of stem surface roughness. PMID:11764342

  1. Tapered cavity surface emitting distributed Bragg reflector lasers

    NASA Astrophysics Data System (ADS)

    Luo, Hui

    2000-09-01

    High power, diffraction-limited semiconductor lasers are required for a wide range of applications such as pumping for EDFAs, Raman amplifiers, and for free space optical communications. Unstable resonator has been identified as a very promising concept to develop these lasers. The objective of this research is to investigate and develop tapered cavity unstable resonator grating coupled surface emitting lasers (TCSELs). The laser consists of a ridge section, a tapered gain section and a DBR grating section. The ridge is used to ensure single lateral mode operation. The taper is used to achieve high power from a large aperture. The grating is used to provide feedback and surface outcoupling. This laser design has several key features including high output power, near diffraction-limited beam, low divergence angle, single longitudinal mode operation, and integration with dynamic functionality such as wavelength tuning and beam steering. In this dissertation the design, fabrication and characterization of TCSELs are discussed. The theory of TCSELs is presented. As a theoretical investigation, a comprehensive numerical modeling based on finite difference beam propagation method (FD-BPM) for semiconductor laser is developed. The model includes major parameters affecting device performance such as current spreading, carrier diffusion, nonlinear gain- carrier relation, gain saturation, carrier induced antiguiding and thermal lensing. The simulation results are presented and effects of design parameters on device performance are discussed. TCSELs with different device design and functionality are fabricated. The characterization results are discussed. High power operation is obtained under both pulsed and continuous wave (CW) operation. Collimated near diffraction-limited beam is demonstrated with moderate power. Single longitudinal mode operation with high side mode suppression ratio is observed. Wavelength tuning and beam steering is achieved using current injection to

  2. Flexibility of K3 and ProTaper universal instruments.

    PubMed

    Grazziotin-Soares, Renata; Barato Filho, Flares; Vanni, José Roberto; Almeida, Susimara; Oliveira, Elias Pandonor Motcy de; Barletta, Fernando Branco; Limongi, Orlando

    2011-01-01

    This study used a mechanical test to evaluate the flexibility of instruments from the K3 (conicity 0.04) and the ProTaper Universal systems when they were new and after 5 uses in simulated canals. Five sets of instruments of each system were tested: K3 (15, 20, 25, 30, 35, 40 and 45) and ProTaper Universal (S1, S2, F1, F2, F3, F4 and F5). Each set of instruments was used to prepare a simulated canal and the same set of instruments was used 5 times (50 canals). The number of each subgroup represented the number of uses: 0 (control), 1, 3 and 5 uses. Before and after each use, the instruments were submitted to a mechanical flexibility test performed in a Versat 502 universal testing machine. Interactions between the instrument and the number of uses were analyzed by ANOVA and Tukey's test at a 5% level of significance. Instruments from both systems presented lower flexibility after the third use compared to the flexibility obtained after uses 0 and 1 (p<0.05), and maintained the same flexibility after the fifth use. The flexibility of instruments from the K3 system decreased with the increase of diameter, irrespective of the number of uses. Among the instruments from the ProTaper Universal system, the shaping files presented greater flexibility than the finishing files. F2 and F3 were the least flexible instruments, and F4 and F5 presented flexibility values similar to those of F1.

  3. Spatial frequency multiplier with active linearly tapered slot antenna array

    NASA Astrophysics Data System (ADS)

    Simons, Rainee N.; Lee, Richard Q.

    1994-02-01

    A frequency multiplier with active linearly tapered slot antennas (LTSA's) has been demonstrated at the second harmonic frequency. In each antenna element, a GaAs monolithic microwave integrated circuit (MMIC) distributed amplifier is integrated with two LTSA's. The multiplier has a very wide bandwidth and large dynamic range. The fundamental-to-second harmonic conversion efficiency is 8.1 percent. The spatially combined second harmonic signal is 50 dB above the noise level. The design is suitable for constructing a large array using monolithic integration techniques.

  4. Compound-taper feed horn for NASA 70-m antennas

    NASA Technical Reports Server (NTRS)

    Manshadi, Farzin; Hartop, Rob

    1988-01-01

    A novel X-band feedhorn was designed for the Deep Space Network (DSN) 70-meter antennas. The feedhorn is a compound-taper structure consisting of a corrugated flared section and a corrugated straight section. This feedhorn is designed to closely imitate the characteristics of the standard feedhorn, while providing the proper phase center location, without adding any significant loss to the system. The use of the existing feedhorn and the ease of manufacturing the corrugated straight section have resulted in major overall cost savings.

  5. Modeling taper charge with a non-linear equation

    NASA Technical Reports Server (NTRS)

    Mcdermott, P. P.

    1985-01-01

    Work aimed at modeling the charge voltage and current characteristics of nickel-cadmium cells subject to taper charge is presented. Work reported at previous NASA Battery Workshops has shown that the voltage of cells subject to constant current charge and discharge can be modeled very accurately with the equation: voltage = A + (B/(C-X)) + De to the -Ex where A, B, D, and E are fit parameters and x is amp-hr of charge removed during discharge or returned during charge. In a constant current regime, x is also equivalent to time on charge or discharge.

  6. Compound-taper feedhorn for the DSN 70-meter antennas

    NASA Technical Reports Server (NTRS)

    Manshadi, F.; Hartop, R.

    1987-01-01

    A novel X-band feedhorn was designed for the Deep Space Network (DSN) 70-meter antennas. The feedhorn is a compound-taper structure consisting of a corrugated flared section and a corrugated straight section. This feedhorn is designed to closely initiate the characteristics of the standard feedhorn, while providing the proper phase center location, without adding any significant loss to the system. The use of the existing feedhorn and the ease of manufacturing the corrugated straight section have resulted in major overall cost savings.

  7. Method of making tapered capillary tips with constant inner diameters

    DOEpatents

    Kelly, Ryan T.; Page, Jason S.; Tang, Keqi; Smith, Richard D.

    2009-02-17

    Methods of forming electrospray ionization emitter tips are disclosed herein. In one embodiment, an end portion of a capillary tube can be immersed into an etchant, wherein the etchant forms a concave meniscus on the outer surface of the capillary. Variable etching rates in the meniscus can cause an external taper to form. While etching the outer surface of the capillary wall, a fluid can be flowed through the interior of the capillary tube. Etching continues until the immersed portion of the capillary tube is completely etched away.

  8. Supercontinuum generation in dispersion-managed tapered-rib waveguide.

    PubMed

    Hu, Hongyu; Li, Wenbo; Dutta, Niloy K

    2013-10-20

    We have designed a tapered-rib waveguide and numerically studied the generation of supercontinuum using such waveguides. The Air-SF57 glass-SiO(2) waveguide is 3 cm long, with a varying etched depth to manage the total dispersion. Numerical simulations are conducted for input pulses at a wavelength of 1.55 μm with a width of 150 fs and peak power of 5 kW. The proposed waveguide geometry greatly broadens the output spectrum, extending from ∼1 to ∼6  μm, caused by the continuous modification of the phase-matching condition for the generated waves.

  9. Space Power Amplification with Active Linearly Tapered Slot Antenna Array

    NASA Technical Reports Server (NTRS)

    Simons, Rainee N.; Lee, Richard Q.

    1993-01-01

    A space power amplifier composed of active linearly tapered slot antennas (LTSA's) has been demonstrated and shown to have a gain of 30 dB at 20 GHz. In each of the antenna elements, a GaAs monolithic microwave integrated circuit (MMIC) three-stage power amplifier is integrated with two LTSA's. The LTSA and the MMIC power amplifier has a gain of 11 dB and power added efficiency of 14 percent respectively. The design is suitable for constructing a large array using monolithic integration techniques.

  10. Method speeds tapered rod design for directional well

    SciTech Connect

    Hu Yongquan; Yuan Xiangzhong

    1995-10-16

    Determination of the minimum rod diameter, from statistical relationships, can decrease the time needed for designing a sucker-rod string for a directional well. A tapered rod string design for a directional well is more complex than for a vertical well. Based on the theory of a continuous beam column, the rod string design in a directional well is a trial and error method. The key to reduce the time to obtain a solution is to rapidly determine the minimum rod diameter. This can be done with a statistical relationship. The paper describes sucker rods, design method, basic analysis rod design, and minimum rod diameter.

  11. Spatial frequency multiplier with active linearly tapered slot antenna array

    NASA Technical Reports Server (NTRS)

    Simons, Rainee N.; Lee, Richard Q.

    1994-01-01

    A frequency multiplier with active linearly tapered slot antennas (LTSA's) has been demonstrated at the second harmonic frequency. In each antenna element, a GaAs monolithic microwave integrated circuit (MMIC) distributed amplifier is integrated with two LTSA's. The multiplier has a very wide bandwidth and large dynamic range. The fundamental-to-second harmonic conversion efficiency is 8.1 percent. The spatially combined second harmonic signal is 50 dB above the noise level. The design is suitable for constructing a large array using monolithic integration techniques.

  12. Supercontinuum generation in dispersion-managed tapered-rib waveguide.

    PubMed

    Hu, Hongyu; Li, Wenbo; Dutta, Niloy K

    2013-10-20

    We have designed a tapered-rib waveguide and numerically studied the generation of supercontinuum using such waveguides. The Air-SF57 glass-SiO(2) waveguide is 3 cm long, with a varying etched depth to manage the total dispersion. Numerical simulations are conducted for input pulses at a wavelength of 1.55 μm with a width of 150 fs and peak power of 5 kW. The proposed waveguide geometry greatly broadens the output spectrum, extending from ∼1 to ∼6  μm, caused by the continuous modification of the phase-matching condition for the generated waves. PMID:24216588

  13. Dispersion-engineered tapered planar waveguide for coherent supercontinuum generation

    NASA Astrophysics Data System (ADS)

    Hu, Hongyu; Li, Wenbo; Dutta, Niloy K.

    We have designed a tapered planar rib waveguide and numerically studied supercontinuum generation by the propagation of input pulses at 1.55 μm. The Air-SF57 glass-SiO2 waveguide is 2 cm long, with a varying etch depth to manage the total dispersion. This proposed waveguide geometry significantly broadens the output spectrum caused by continuous modification of the phase matching condition for dispersive wave emission. The coherence property has also been investigated, demonstrating that fully coherent supercontinuum extending from ~1 μm to ~4.6 μm can be obtained with proper pumping conditions.

  14. Nanofocusing of terahertz wave in a tapered hyperbolic metal waveguide.

    PubMed

    Gao, Hua; Cao, Qing; Zhu, Minning; Teng, Da; Shen, Siyi

    2014-12-29

    An tapered hyperbolic metal waveguide is suggested for the nanofocusing of terahertz waves. We numerically show that, at the frequency of 1 THz, the focal spot can be as small as only 5 nm, which is smaller than that of a plate waveguide by 2 orders of magnitude. Correspondingly, the longitudinal component of the energy flow density is stronger than that of a plate waveguide by 3 orders of magnitude for the same input. It is shown that these significant improvements come from the small imaginary part of the effective index of the hyperbolic metal waveguide.

  15. Design and Manufacture of Structurally Efficient Tapered Struts

    NASA Technical Reports Server (NTRS)

    Brewster, Jebediah W.

    2009-01-01

    Composite materials offer the potential of weight savings for numerous spacecraft and aircraft applications. A composite strut is just one integral part of the node-to-node system and the optimization of the shut and node assembly is needed to take full advantage of the benefit of composites materials. Lockheed Martin designed and manufactured a very light weight one piece composite tapered strut that is fully representative of a full scale flight article. In addition, the team designed and built a prototype of the node and end fitting system that will effectively integrate and work with the full scale flight articles.

  16. Design charts relating to the stalling of tapered wings

    NASA Technical Reports Server (NTRS)

    Soule, H A; Anderson, R F

    1940-01-01

    An aid in airplane design, charts have been prepared to show the effects of wing taper, thickness ratio, and Reynolds number on the spanwise location of the initial stalling point. Means of improving poor stalling characteristics resulting from certain combinations of the variables have also been considered; additional figures illustrate the influence of camber increase to the wing tips, washout, central sharp leading edges, and wing-tip slots on the stalling characteristics. Data are included from which the drag increases resulting from the use of these means can be computed. The application of the data to a specific problem is illustrated by an example.

  17. Asymmetric laser sideband generation with a tapered semiconductor amplifier

    NASA Astrophysics Data System (ADS)

    Yanakas, Michael; Lim, Michael

    2013-03-01

    We have constructed a free-space, frequency-shifted feedback amplifier using a tapered semiconductor gain element. The general layout of the system is similar to that described in Littler, et al., Opt. Comm. 88, 523 (1992). Traveling-wave feedback is demonstrated with the m = - 1 order of several different acousto-optic modulators driven at variable frequency. Asymmetric sideband production is observed in the rf spectrum of a fast photodiode and in the transmission of a scanning Fabry-Perot interferometer. The number of asymmetric modes is controlled with the AOM rf drive power and the seed laser optical power. Supported by NSF PHY-0613659

  18. Tunable ring laser using a tapered single mode fiber tip.

    PubMed

    Wang, Xiaozhen; Li, Yi; Bao, Xiaoyi

    2009-12-10

    A tunable ring laser using a tapered single mode fiber tip as a bandpass filter has been proposed and demonstrated for the first time to our knowledge. This is a simple and cost-effective tunable source. It is found that the tuning range and bandwidth of the laser are related to the relaxation time of the optical amplifier, the current of the amplifier, and the steepness of the tip shape. The calculations and experimental results show that the laser has a tuning range of 9 nm in the L-band and the spectral linewidth can be varied from 0.06 nm to 0.17 nm. PMID:20011024

  19. Characterization of tapered slot antenna feeds and feed arrays

    NASA Technical Reports Server (NTRS)

    Kim, Young-Sik; Yngvesson, K. Sigfrid

    1990-01-01

    A class of feed antennas and feed antenna arrays used in the focal plane of paraboloid reflectors and exhibiting higher than normal levels of cross-polarized radiation in the diagonal planes is addressed. A model which allows prediction of element gain and aperture efficiency of the feed/reflector system is presented. The predictions are in good agreement with experimental results. Tapered slot antenna (TSA) elements are used an example of an element of this type. It is shown that TSA arrays used in multibeam systems with small beam spacings are competitive in terms of aperture efficiency with other, more standard types of arrays incorporating waveguide type elements.

  20. Tapered slot antenna design for vehicular GPR applications

    NASA Astrophysics Data System (ADS)

    Bıçak, Emrullah; Yeǧin, Korkut; Nazlı, Hakki; Daǧ, Mahmut

    2014-05-01

    Vehicular applications of UWB GPR demand multiple GPR sensors operating in a harsh environment. One of the key elements of in the sensor is its UWB antenna which has minimal inter-element coupling, low group delay, high directivity and less prone to environmental conditions. Tapered slot antennas (TSA's) provide good impedance match, but they need to be modified for above specifications. Parasitic slot loaded TSA with balanced feed is proposed and a multi-channel antenna array structure is formed. Structural parameters are numerically analyzed and a prototype is built. Measurements show good performance for UWB GPR applications.

  1. Gain saturation and high-power pulsed operation of GaSb-based tapered diode lasers with separately contacted ridge and tapered section

    NASA Astrophysics Data System (ADS)

    Pfahler, C.; Eichhorn, M.; Kelemen, M. T.; Kaufel, G.; Mikulla, M.; Schmitz, J.; Wagner, J.

    2006-07-01

    (AlGaIn)(AsSb) ridge-waveguide tapered diode lasers with separately contacted ridge and tapered sections, emitting at 1.93μm, have been analyzed in pulsed mode with respect to their high-power capability and wavelength tunability. Operating the ridge section above saturation, a variation of the current through this section resulted in a change in lasing wavelength, while changing the current injected into the tapered section at a constant ridge current allowed to vary the output power at constant lasing wavelength. Furthermore, the optical power required to saturate the tapered amplifier section has been derived from a comparison of the experimental characteristics with beam propagation method calculations.

  2. Aperture taper determination for the half-scale accurate antenna reflector

    NASA Technical Reports Server (NTRS)

    Lambert, Kevin M.

    1990-01-01

    A simulation is described of a proposed microwave reflectance measurement in which the half scale reflector is used in a compact range type of application. The simulation is used to determine an acceptable aperture taper for the reflector which will allow for accurate measurements. Information on the taper is used in the design of a feed for the reflector.

  3. The mean aerodynamic chord and the aerodynamic center of a tapered wing

    NASA Technical Reports Server (NTRS)

    Diehl, Walter S

    1942-01-01

    A preliminary study of pitching-moment data on tapered wings indicated that excellent agreement with test data was obtained by locating the quarter-chord point of the average chord on the average quarter-chord point of the semispan. The study was therefore extended to include most of the available data on tapered-wing models tested by the NACA.

  4. Dynamic analysis of tapered laminated composite magnetorheological elastomer (MRE) sandwich plates

    NASA Astrophysics Data System (ADS)

    Babu, V. Ramesh; Vasudevan, R.

    2016-03-01

    In the present study, the dynamic performance of the sandwich plate with magneto rheological elastomer (MRE) as the core layer and tapered laminated composite plates as the face layers is investigated. Various MRE tapered laminated composite sandwich plate models are formulated by dropping-off the plies longitudinally in top and bottom composite layers to yield tapered plates as the face layers and uniform MRE layer as the core layer. The governing equations of motion of tapered composite MRE sandwich plates are derived using classical laminated plate theory and solved numerically. Further, silicon based MRE is being fabricated and tested to obtain the shear and loss moduli using MR rheometer. The efficacy of the finite element formulation is validated by carrying out experiments on the various prototypes of tapered composite silicon based MRE sandwich plates and comparing the results in terms of natural frequencies obtained at various magnetic fields with those obtained numerically and with available literature. Also, the effects of magnetic field, taper angle of the top and bottom layers, aspect ratio, ply orientations and various end conditions on the various dynamic properties of tapered laminated composite MRE sandwich plate are investigated. Further, the transverse vibration responses of three different tapered composite MRE based sandwich plates under harmonic force excitation are analyzed at various magnetic fields.

  5. Fire ants protect mealybugs against their natural enemies by utilizing the leaf shelters constructed by the leaf roller Sylepta derogata.

    PubMed

    Zhou, Aiming; Zeng, Ling; Lu, Yongyue; Xu, Yijuan; Liang, Guangwen

    2012-01-01

    The importance of mutualism is receiving more attention in community ecology. In this study, the fire ant Solenopsis invicta was found to take advantage of the shelters constructed by the leaf roller Sylepta derogata to protect mealybugs (Phenacoccus solenopsis) against their natural enemies. This protective effect of fire ant tending on the survival of mealybugs in shelters was observed when enemies and leaf rollers were simultaneously present. Specifically, fire ants moved the mealybugs inside the shelters produced by S. derogata on enemy-infested plants. Compared with that in plants without ants, the survival of mealybugs in shelters in the presence of natural enemies in plants with ants markedly improved. Both the protection of ants and the shelters provided by leaf rollers did not affect the survival of mealybugs in the absence of enemies in plants. Ants and leaf rollers significantly improved the survival of mealybugs in predator-infested plants, whereas no such improvement was observed in parasitoid-infested ones.

  6. Acute, fatal Sarcocystis calchasi-associated hepatitis in Roller pigeons (Columbia livia f. dom.) at Philadelphia Zoo

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Four Roller pigeons (Columba livia f. dom.) at the Philadelphia Zoo died suddenly. Necropsy examination revealed macroscopic hepatitis. Microscopically, the predominant lesions were in liver, characterized with necrosis and mixed cell inflammatory response. Sarcocystis calchasi-like schizonts and fr...

  7. Tapered fluidized bed bioreactor for environmental control and fuel production

    SciTech Connect

    Scott, C. D.; Hancher, C. W.; Arcuri, E. J.

    1980-01-01

    Fluidized bed bioreactors are under development for use in environmental control and energy production. The most effective systems utilize a tapered portion either throughout the column or at the top of the column. This taper allows a wide range of operating conditions without loss of the fluidized particulates, and in general, results in more stable operation. The system described here utilize fixed films of microorganisms that have attached themselves to the fluidized particles. Preliminary investigations of the attachment indicate that reactor performance is related to film thickness. The biological denitrification of aqueous waste streams is typical of processes under development that utilize fluidized bed bioreactors. This development has progressed to the pilot plant scale where two 20-cm-diam x 800-cm fluidized beds in series accept aqueous wastes with nitrate concentrations as high as 10,000 mg/l and denitrification rates greater than 50 g/l/day using residence times of less than 30 minutes in each reactor. Other applications include aerobic degradation of phenolic wastes at rates greater than 25 g/l/day and the conversion of glucose to ethanol.

  8. Spiralling tapered slip-on drill string stabilizer

    SciTech Connect

    Beasley, T.R.; Teng, C.C.

    1986-12-23

    A stabilizer is described for use in a drilling string comprising: a substantially cylindrical body member having a central passageway to accommodate the drill sting, the inside surface of the body member defining a right-hand spiralling thread with a tapered trailing edge which spirals from a starting point on the body member. The thread terminates internally of the body member in an arcuate recess extending around the interior of the body member; a key member is secured to the inner wall surface of the recess of the body member, the key member having a lug extending longitudinally of the body member within the recess; a slip member adapted to thread within the body member between the body member and the drill string. The slip defines a right-hand thread with a matching tapered trailing edge configured to make up with the right-hand thread on the body member and to wedge between the body member and the drill string. One end of the slip terminates in a longitudinally disposed shoulder capable of abutting the lug upon threading of the clip within the body member.

  9. Fatigue Life Analysis of Tapered Hybrid Composite Flexbeams

    NASA Technical Reports Server (NTRS)

    Murri, Gretchen B.; Schaff, Jeffery R.; Dobyns, Alan L.

    2002-01-01

    Nonlinear-tapered flexbeam laminates from a full-size composite helicopter rotor hub flexbeam were tested under combined constant axial tension and cyclic bending loads. The two different graphite/glass hybrid configurations tested under cyclic loading failed by delamination in the tapered region. A 2-D finite element model was developed which closely approximated the flexbeam geometry, boundary conditions, and loading. The analysis results from two geometrically nonlinear finite element codes, ANSYS and ABAQUS, are presented and compared. Strain energy release rates (G) obtained from the above codes using the virtual crack closure technique (VCCT) at a resin crack location in the flexbeams are presented for both hybrid material types. These results compare well with each other and suggest that the initial delamination growth from the resin crack toward the thick region of the flexbeam is strongly mode II. The peak calculated G values were used with material characterization data to calculate fatigue life curves and compared with test data. A curve relating maximum surface strain to number of loading cycles at delamination onset compared reasonably well with the test results.

  10. Analysis of guided wave propagation in a tapered composite panel

    NASA Astrophysics Data System (ADS)

    Wandowski, Tomasz; Malinowski, Pawel; Moll, Jochen; Radzienski, Maciej; Ostachowicz, Wieslaw

    2015-03-01

    Many studies have been published in recent years on Lamb wave propagation in isotropic and (multi-layered) anisotropic structures. In this paper, adiabatic wave propagation phenomenon in a tapered composite panel made out of glass fiber reinforced polymers (GFRP) will be considered. Such structural elements are often used e.g. in wind turbine blades and aerospace structures. Here, the wave velocity of each wave mode does not only change with frequency and the direction of wave propagation. It further changes locally due to the varying cross-section of the GFRP panel. Elastic waves were excited using a piezoelectric transducer. Full wave-field measurements using scanning Laser Doppler vibrometry have been performed. This approach allows the detailed analysis of elastic wave propagation in composite specimen with linearly changing thickness. It will be demonstrated here experimentally, that the wave velocity changes significantly due to the tapered geometry of the structure. Hence, this work motivates the theoretical and experimental analysis of adiabatic mode propagation for the purpose of Non-Destructive Testing and Structural Health Monitoring.

  11. Flow and acoustic features of a supersonic tapered nozzle

    NASA Astrophysics Data System (ADS)

    Gutmark, E.; Bowman, H. L.; Schadow, K. C.

    1992-05-01

    The acoustic and flow characteristics of a supersonic tapered jet were measured for free and shrouded flow configurations. Measurements were performed for a full range of pressure ratios including over- and underexpanded and design conditions. The supersonic tapered jet is issued from a converging-diverging nozzle with a 3∶1 rectangular slotted throat and a conical diverging section leading to a circular exit. The jet was compared to circular and rectangular supersonic jets operating at identical conditions. The distinct feature of the jet is the absence of screech tones in the entire range of operation. Its near-field pressure fluctuations have a wide band spectrum in the entire range of measurements, for Mach numbers of 1 to 2.5, for over- and underexpanded conditions. The free jet's spreading rate is nearly constant and similar to the rectangular jet, and in a shroud, the pressure drop it is inducing is linearly proportional to the primary jet Mach number. This behavior persisted in high adverse pressure gradients at overexpanded conditions, and with nozzle divergence angles of up to 35°, no inside flow separation was observed.

  12. Optimization of tapered fiber sample for laser cooling of solids

    NASA Astrophysics Data System (ADS)

    Nemova, Galina; Kashyap, Raman

    2009-02-01

    The physical mechanism of radiation cooling by anti-Stokes fluorescence was originally proposed in 1929 and experimentally observed in solid materials in 1995 by Epstein's research team in ytterbium-doped ZBLANP glass. Some specific combinations of the ions, host materials, and the wavelength of the incident radiation can provide anti-Stokes interaction resulting in phonon absorption accompanied by the cooling of the host material. Although the optical cooling of the Yb3+-doped ZBLANP sample was already observed there are broad possibilities for its improvement to increase the temperature-drop of the sample by optimization of the geometrical parameters of the cooling sample. We propose a theoretical model for an optimized tapered fiber structure for use as a sample in anti-Stokes laser cooling of solids. This tapered fiber has a fluorozirconate glass ZBLANP with a core doped with Yb3+ or Tm3+ ions. As evident from the results of our work, the appropriate choice of the fiber core and the fiber cladding radii can significantly increase the temperature-drop of the sample for any fixed pump power. The value of the maximum of the temperature-drop of the sample increases with an increase in the pump power. The depletion of the pump power causes a temperature gradient along the length of the cooled sample.

  13. Optimization of epitaxial layer design for high brightness tapered lasers

    NASA Astrophysics Data System (ADS)

    Tijero, J. M. G.; Rodriguez, D.; Borruel, L.; Sujecki, S.; Larkins, E. C.; Esquivias, I.

    2005-04-01

    A comparative simulation study of the optical output characteristics of tapered lasers with different epitaxial structure was performed. The simulation model self-consistently solves the steady state electrical and optical equations for the flared unstable resonator and was previously backed by experiments on one of the simulated structures. Three different epitaxial designs emitting at 975 nm were analyzed: a standard single quantum well symmetrically located in the confinement region (s-SQW), a double quantum well also symmetrically located (s-DQW) and an asymmetrically located double quantum well (a-DQW). The symmetric structures have different confinement factor but a similar ratio between the active layer thickness and the confinement factor, dQW/Γ, while the a-DQW has similar confinement factor than the s-SQW, but double dQW/Γ. A better performance is predicted for the a-DQW design, reaching considerably higher output power with good beam quality. The results are interpreted in terms of a lower density of power in the QW in the case of the a-DQW design, thus delaying to higher output power the onset of the non-linear effects that degrade the beam quality. The role of dQW/Γ as a figure of merit for high brightness tapered lasers is emphasized.

  14. Moment method analysis of linearly tapered slot antennas

    NASA Technical Reports Server (NTRS)

    Koeksal, Adnan

    1993-01-01

    A method of moments (MOM) model for the analysis of the Linearly Tapered Slot Antenna (LTSA) is developed and implemented. The model employs an unequal size rectangular sectioning for conducting parts of the antenna. Piecewise sinusoidal basis functions are used for the expansion of conductor current. The effect of the dielectric is incorporated in the model by using equivalent volume polarization current density and solving the equivalent problem in free-space. The feed section of the antenna including the microstripline is handled rigorously in the MOM model by including slotline short circuit and microstripline currents among the unknowns. Comparison with measurements is made to demonstrate the validity of the model for both the air case and the dielectric case. Validity of the model is also verified by extending the model to handle the analysis of the skew-plate antenna and comparing the results to those of a skew-segmentation modeling results of the same structure and to available data in the literature. Variation of the radiation pattern for the air LTSA with length, height, and taper angle is investigated, and the results are tabulated. Numerical results for the effect of the dielectric thickness and permittivity are presented.

  15. Fatigue Life Methodology for Tapered Hybrid Composite Flexbeams

    NASA Technical Reports Server (NTRS)

    urri, Gretchen B.; Schaff, Jeffery R.

    2006-01-01

    Nonlinear-tapered flexbeam specimens from a full-size composite helicopter rotor hub flexbeam were tested under combined constant axial tension and cyclic bending loads. Two different graphite/glass hybrid configurations tested under cyclic loading failed by delamination in the tapered region. A 2-D finite element model was developed which closely approximated the flexbeam geometry, boundary conditions, and loading. The analysis results from two geometrically nonlinear finite element codes, ANSYS and ABAQUS, are presented and compared. Strain energy release rates (G) associated with simulated delamination growth in the flexbeams are presented from both codes. These results compare well with each other and suggest that the initial delamination growth from the tip of the ply-drop toward the thick region of the flexbeam is strongly mode II. The peak calculated G values were used with material characterization data to calculate fatigue life curves for comparison with test data. A curve relating maximum surface strain to number of loading cycles at delamination onset compared well with the test results.

  16. Intensity modulated SMF cascaded tapers with a hollow core PCF based microcavity for curvature sensing

    NASA Astrophysics Data System (ADS)

    Dass, Sumit; Narayan Dash, Jitendra; Jha, Rajan

    2016-03-01

    We propose a highly sensitive curvature sensor based on cascaded single mode fiber (SMF) tapers with a microcavity. The microcavity is created by splicing a small piece of hollow core photonic crystal fiber (HCPCF) at the end of an SMF to obtain a sharp interference pattern. Experimental results show that two SMF tapers enhance the curvature sensitivity of the system and by changing the tapering parameters of the second taper, the curvature sensitivity of the system can be tailored, together with the fringe contrast of the interference pattern. A maximum curvature sensitivity of 10.4 dB/m-1 is observed in the curvature range 0 to 1 m-1 for a second taper diameter of 18 μm. The sensing setup is highly stable and shows very low temperature sensitivity. As the interrogation is intensity based, a low cost optical power meter can be utilized to determine the curvature.

  17. Acousto-optic interaction in biconical tapered fibers: shaping of the stopbands

    NASA Astrophysics Data System (ADS)

    Ramírez-Meléndez, Gustavo; Bello-Jiménez, Miguel Ángel; Cuadrado-Laborde, Christian; Díez, Antonio; Cruz, José Luis; Rodríguez-Cobos, Amparo; Balderas-Navarro, Raúl; Andrés Bou, Miguel Vicente

    2016-03-01

    The effect of a gradual reduction of the fiber diameter on the acousto-optic (AO) interaction is reported. The experimental and theoretical study of the intermodal coupling induced by a flexural acoustic wave in a biconical tapered fiber shows that it is possible to shape the transmission spectrum, for example, substantially broadening the bandwidth of the resonant couplings. The geometry of the taper transitions can be regarded as an extra degree of freedom to design the AO devices. Optical bandwidths above 45 nm are reported in a tapered fiber with a gradual reduction of the fiber down to 70 μm diameter. The effect of including long taper transition is also reported in a double-tapered structure. A flat attenuation response is reported with 3-dB stopband bandwidth of 34 nm.

  18. Spectral tuning of a locally bent microfiber taper interferometer with a nanosized liquid crystal overlay.

    PubMed

    Luo, Haimei; Wang, Changjing; Ji, Yinghua; Yuan, Wen; Zhang, Guoping; Wang, Yifan; Hong, Zehua; Wang, Xianping

    2016-09-10

    In this paper, the tuning characteristics of locally bent microfiber taper covered with a nanosized high-refractive-index liquid crystal (LC) layer under different temperatures and electric field intensities have been theoretically analyzed and experimentally investigated. A locally bent microfiber taper interferometer with a waist diameter of ∼3.72  μm is fabricated by using the flame brushing technique, followed by bending the transition region of the taper to form a modal interferometer and later by placing a ∼200  nm LC layer over the uniform taper waist region. Experimental results indicate that a high-efficiency thermal or electric tuning of an LC-coated locally bent microfiber taper interferometer could be achieved. This suggests a potential application of this device as tunable all-fiber photonic devices, such as filters, modulators, and sensing elements.

  19. Locking strength of Morse tapers used for modular segmental bone defect replacement prostheses.

    PubMed

    Duda, G N; Elias, J J; Valdevit, A; Chao, E Y

    1997-01-01

    Mechanical testing has been performed to characterize the locking strength of Morse taper locks used for reconstruction of large bone defects. Taper joint pairs were locked with a series of compressive loads increasing from 500 to 3500 N. Following each load application the taper locks were distracted with either an axial load or a torsional load. Additional tapers were loaded with 2 million cycles of axial compression or 2 million cycles of cantilever bending combined with axial compression, followed by axial distraction. The torsional and axial distraction loads increased linearly with the compressive load. Compared to a single compressive load application, cyclic axial loading had little influence on the joint strength, while a combination of axial loading and bending increased the joint strength. Based on these results, in vivo loading should increase the locking strength of Morse taper locks used for bone defect reconstruction.

  20. Spectral tuning of a locally bent microfiber taper interferometer with a nanosized liquid crystal overlay.

    PubMed

    Luo, Haimei; Wang, Changjing; Ji, Yinghua; Yuan, Wen; Zhang, Guoping; Wang, Yifan; Hong, Zehua; Wang, Xianping

    2016-09-10

    In this paper, the tuning characteristics of locally bent microfiber taper covered with a nanosized high-refractive-index liquid crystal (LC) layer under different temperatures and electric field intensities have been theoretically analyzed and experimentally investigated. A locally bent microfiber taper interferometer with a waist diameter of ∼3.72  μm is fabricated by using the flame brushing technique, followed by bending the transition region of the taper to form a modal interferometer and later by placing a ∼200  nm LC layer over the uniform taper waist region. Experimental results indicate that a high-efficiency thermal or electric tuning of an LC-coated locally bent microfiber taper interferometer could be achieved. This suggests a potential application of this device as tunable all-fiber photonic devices, such as filters, modulators, and sensing elements. PMID:27661380

  1. Theoretical span loading and moments of tapered wings produced by aileron deflection

    NASA Technical Reports Server (NTRS)

    Pearson, H A

    1937-01-01

    The effect of tapered ailerons on linearly tapered wings is theoretically determined. Four different aileron spans are considered for each of three wing aspect ratios and each of four wing taper ratios. The change in lift on one half of the wing, the rolling moment, the additional induced drag, and the yawing moment, due to aileron deflection, are represented by non dimensional coefficients. Similar coefficients are given for the damping and yawing moments, the additional drag, and the change in lift, due to rolling. It was found possible to effect a fairly close agreement between the theoretical and experimental rolling moments by introducing into the theoretical expression for the rolling moment an effective change in angle of attack obtained from an analysis of flap data. The theoretical curves show that the highly tapered wing with long ailerons has a lower ratio of yawing to rolling moment and a lower additional induced drag than wings with less taper.

  2. Quantitative evaluation of apically extruded debris during root canal instrumentation with ProTaper Universal, ProTaper Next, WaveOne, and self-adjusting file systems

    PubMed Central

    Ozsu, Damla; Karatas, Ertugrul; Arslan, Hakan; Topcu, Meltem C.

    2014-01-01

    Objectives: The aim of this study was to compare the amount of apically extruded debris during preparation with ProTaper Universal (Dentsply Maillefer, Ballaigues, Switzerland), ProTaper Next (Dentsply Maillefer), a reciprocating single-file (WaveOne; VDW GmbH, Munich, Germany), and a self-adjusting file (SAF; ReDent Nova, Ra’anna, Israel). Materials and Methods: Fifty-six intact mandibular premolar teeth were randomly assigned to four groups. The root canals were prepared according to the manufacturers’ instructions using the ProTaper Universal, ProTaper Next, WaveOne, and SAF. Apically extruded debris was collected in preweighted Eppendorf tubes during instrumentation. The net weight of the apically extruded debris was determined by subtracting the preweights and postweights of the tubes. The data were statistically analyzed using the one-way analysis of variance and the least significant difference tests at a significance level of P < 0.05. Results: A measurable amount of debris was apically extruded in all groups, and the amounts of debris extrusion in the groups were statistically significant (P < 0.001). The ProTaper Next and WaveOne groups resulted in less debris extrusion than the ProTaper Universal group (P < 0.05), and the SAF group resulted in the least debris extrusion. Conclusions: Within the limitations of the present study, it can be concluded that all systems extruded debris beyond the apical foramen. PMID:25512732

  3. Comparison of canal transportation in simulated curved canals prepared with ProTaper Universal and ProTaper Gold systems

    PubMed Central

    Muniz, Brenda Leite; Pires, Frederico; Belladonna, Felipe Gonçalves; Neves, Aline Almeida; Souza, Erick Miranda; De-Deus, Gustavo

    2016-01-01

    Objectives The purpose of this study was to assess the ability of ProTaper Gold (PTG, Dentsply Maillefer) in maintaining the original profile of root canal anatomy. For that, ProTaper Universal (PTU, Dentsply Maillefer) was used as reference techniques for comparison. Materials and Methods Twenty simulated curved canals manufactured in clear resin blocks were randomly assigned to 2 groups (n = 10) according to the system used for canal instrumentation: PTU and PTG groups, upto F2 files (25/0.08). Color stereomicroscopic images from each block were taken exactly at the same position before and after instrumentation. All image processing and data analysis were performed with an open source program (FIJI). Evaluation of canal transportation was obtained for two independent canal regions: straight and curved levels. Student's t test was used with a cut-off for significance set at α = 5%. Results Instrumentation systems significantly influenced canal transportation (p < 0.0001). A significant interaction between instrumentation system and root canal level (p < 0.0001) was found. PTU and PTG systems produced similar canal transportation at the straight part, while PTG system resulted in lower canal transportation than PTU system at the curved part. Canal transportation was higher at the curved canal portion (p < 0.0001). Conclusions PTG system produced overall less canal transportation in the curved portion when compared to PTU system. PMID:26877984

  4. Effect of Internal Clearance on Load Distribution and Life of Radially Loaded Ball and Roller Bearings

    NASA Technical Reports Server (NTRS)

    Oswald, Fred B.; Zaretsky, Erwin V.; Poplawski, Joseph V.

    2012-01-01

    The effect of internal clearance on radially loaded deepgroove ball and cylindrical roller bearing load distribution and fatigue life was determined for four clearance groups defined in the bearing standards. The analysis was extended to negative clearance (interference) conditions to produce a curve of life factor versus internal clearance. Rolling-element loads can be optimized and bearing life maximized for a small negative operating clearance. Life declines gradually with positive clearance and rapidly with increasing negative clearance. Relationships were found between bearing life and internal clearance as a function of ball or roller diameter, adjusted for load. Results are presented as life factors for radially loaded bearings independent of bearing size or applied load. In addition, a modified Stribeck Equation is presented that relates the maximum rolling-element load to internal bearing clearance.

  5. Pervasive liquid metal based direct writing electronics with roller-ball pen

    SciTech Connect

    Zheng, Yi; Zhang, Qin; Liu, Jing

    2013-11-15

    A roller-ball pen enabled direct writing electronics via room temperature liquid metal ink was proposed. With the rolling to print mechanism, the metallic inks were smoothly written on flexible polymer substrate to form conductive tracks and electronic devices. The contact angle analyzer and scanning electron microscope were implemented to disclose several unique inner properties of the obtained electronics. An ever high writing resolution with line width and thickness as 200 μm and 80 μm, respectively was realized. Further, with the administration of external writing pressure, GaIn{sub 24.5} droplets embody increasing wettability on polymer which demonstrates the pervasive adaptability of the roller-ball pen electronics.

  6. Micromagnetic simulation of thermal ripple in thin films: ``Roller-coaster'' visualization

    NASA Astrophysics Data System (ADS)

    Feng, Xuebing; Visscher, P. B.; Apalkov, D. M.

    2003-05-01

    We present simulations of pulse-induced magnetization-rotation experiments in Permalloy. These lead to temporary domain formation ("thermal ripple") and help to explain the time dependence of experimental results. To understand and visualize the motion, we find it very useful to exploit a mathematical isomorphism of this problem (in the limit Ms≫Hpulse) to the problem of a massive particle on a circular track ("roller coaster"). The height (gravitational potential energy) of this track is proportional to the Stoner-Wohlfarth energy. The fact that the resulting "precession" is really oscillation in a plane, and the fact that this oscillation overshoots the minimum-energy configuration (the inertia effect) are much more intuitive in the roller coaster picture than in the conventional "M precesses about the effective field" picture. Animated simulations of this behavior are available on the web (http://bama.ua.edu/˜visscher/mumag/).

  7. Resolution of sudden sensorineural hearing loss following a roller coaster ride.

    PubMed

    Kumar, Aman; Sinha, Amrita; Al-Waa, Ahmad M

    2011-07-01

    We report a case of sudden unilateral sensorineural hearing loss of sudden onset during an aeroplane flight, which completely resolved during a roller coaster ride at Alton Towers theme park. A review of the literature concerning sudden idiopathic sensorineural hearing loss and spontaneous resolution are discussed. Initially, pure-tone audiometry showed a profound sensorineural hearing loss in the right ear and mild sensorineural hearing loss in the left ear (of note, the hearing was normal prior to the episode). Following resolution of the patient's symptoms during a roller coaster ride, pure-tone audiometry showed normal hearing thresholds in both ears. Sudden sensorineural hearing loss is a symptom of cochlear injury and the mechanism of the patient's symptoms was attributed to a patent cochlear aqueduct. PMID:22754856

  8. Pervasive liquid metal based direct writing electronics with roller-ball pen

    NASA Astrophysics Data System (ADS)

    Zheng, Yi; Zhang, Qin; Liu, Jing

    2013-11-01

    A roller-ball pen enabled direct writing electronics via room temperature liquid metal ink was proposed. With the rolling to print mechanism, the metallic inks were smoothly written on flexible polymer substrate to form conductive tracks and electronic devices. The contact angle analyzer and scanning electron microscope were implemented to disclose several unique inner properties of the obtained electronics. An ever high writing resolution with line width and thickness as 200 μm and 80 μm, respectively was realized. Further, with the administration of external writing pressure, GaIn24.5 droplets embody increasing wettability on polymer which demonstrates the pervasive adaptability of the roller-ball pen electronics.

  9. Statistical model and control of a ring-and-roller type grinding mill

    SciTech Connect

    Cho, S.

    1992-01-01

    This project explores the use of a ring-and-roller grinding mill for fine grinding or pulverizing. Since the efficiency of this system is low, small improvements in product throughput or energy consumption can result in substantial economic improvements. To better understand this system, experiments were conducted for limestone and cement clinker. From these experiments models were formulated for product throughput, energy consumption and product size distribution. A control loop was implemented to reduce the effect of non-uniform feeding. Steady-state interactions were analyzed using the Relative Gain Array (RGA) method. Next, a multi-input and multi-output (MIMO) control system was designed using the Inverse Nyquist Array (INA) method to remove variable interactions. The robustness of this controller was explored. Finally, a self-tuning PI controller was designed using the pole placement method to improve system performance. The results of this study provide models for implementation on ring-and-roller grinding mills.

  10. Resolution of sudden sensorineural hearing loss following a roller coaster ride.

    PubMed

    Kumar, Aman; Sinha, Amrita; Al-Waa, Ahmad M

    2011-07-01

    We report a case of sudden unilateral sensorineural hearing loss of sudden onset during an aeroplane flight, which completely resolved during a roller coaster ride at Alton Towers theme park. A review of the literature concerning sudden idiopathic sensorineural hearing loss and spontaneous resolution are discussed. Initially, pure-tone audiometry showed a profound sensorineural hearing loss in the right ear and mild sensorineural hearing loss in the left ear (of note, the hearing was normal prior to the episode). Following resolution of the patient's symptoms during a roller coaster ride, pure-tone audiometry showed normal hearing thresholds in both ears. Sudden sensorineural hearing loss is a symptom of cochlear injury and the mechanism of the patient's symptoms was attributed to a patent cochlear aqueduct.

  11. A roller-like bird (Coracii) from the Early Eocene of Denmark

    PubMed Central

    Bourdon, Estelle; Kristoffersen, Anette V.; Bonde, Niels

    2016-01-01

    The fossil record of crown group birds (Neornithes) prior to the Cretaceous-Paleogene boundary is scarce and fragmentary. Early Cenozoic bird fossils are more abundant, but are typically disarticulated and/or flattened. Here we report the oldest roller (Coracii), Septencoracias morsensis gen. et sp. nov. (Primobucconidae), based on a new specimen from the Early Eocene (about 54 million years ago) Fur Formation of Denmark. The new fossil is a nearly complete, three-dimensionally preserved and articulated skeleton. It lies at the lower end of the size range for extant rollers. Salient diagnostic features of Septencoracias relative to other Coracii include the proportionally larger skull and the small, ovoid and dorsally positioned narial openings. Our discovery adds to the evidence that the Coracii had a widespread northern hemisphere distribution in the Eocene. Septencoracias is the oldest substantial record of the Picocoraciae and provides a reliable calibration point for molecular phylogenetic studies. PMID:27670387

  12. Acceleration in one, two, and three dimensions in launched roller coasters

    NASA Astrophysics Data System (ADS)

    Pendrill, Ann-Marie

    2008-09-01

    During a roller coaster ride, the body experiences acceleration in three dimensions. An accelerometer can measure and provide a graph of the forces on the body during different parts of a ride. To couple the experience of the body to pictures of the ride and an analysis of data can contribute to a deeper understanding of Newton's laws. This article considers the physics of launched roller coasters. Measurements were performed with a three-dimensional co-moving accelerometer. An analysis is presented of the forces in the different ride elements of the Kanonen in Göteborg and the Speed Monster in Oslo, which both include loops and offer rich examples of force and acceleration in all dimensions.

  13. Designing Drops, Loops, and Hills: The Physics behind Roller Coaster Design

    NASA Astrophysics Data System (ADS)

    Christiana, Katharyn; Ilie, Carolina

    2013-03-01

    Almost everyone has seen a roller coaster at one time in their life. They range in type from old wooden coasters from decades passes to modern machines made of steel that allow you to stand up while riding. The basic physics behind these machines is relatively simple, but in the modern world we strive to design bigger and better machines that push the human body and the laws of physics to their limits. But how do the designers of these rides maintain the balance between making riders feel like they're on the brink of death while keeping them completely safe? The answer can be found in basic physics and mechanical engineering. This is a part of the honors thesis that focuses on the mechanical principles applied in roller coaster design. The theoretical part of the thesis will be complemented by a full small scale ride design.

  14. High Efficiency Electron-Laser Interactions in Tapered Helical Undulators

    NASA Astrophysics Data System (ADS)

    Duris, Joseph Patrick

    Efficient coupling of relativistic electron beams with high power radiation lies at the heart of advanced accelerator and light source research and development. The inverse free electron laser is a stable accelerator capable of harnessing very high intensity laser electric fields to efficiently transfer large powers from lasers to electron beams. In this dissertation, we first present the theoretical framework to describe the interaction, and then apply our improved understanding of the IFEL to the design and numerical study of meter-long, GeV IFELs for compact light sources. The central experimental work of the dissertation is the UCLA BNL helical inverse free electron laser experiment at the Accelerator Test Facility in Brookhaven National Laboratory which used a strongly tapered 54cm long, helical, permanent magnet undulator and a several hundred GW CO2 laser to accelerate electrons from 52 to 106MeV, setting new records for inverse free electron laser energy gain (54MeV) and average accelerating gradient (100MeV/m). The undulator design and fabrication as well as experimental diagnostics are presented. In order to improve the stability and quality of the accelerated electron beam, we redesigned the undulator for a slightly reduced output energy by modifying the magnet gap throughout the undulator, and we used this modified undulator to demonstrated capture of >25% of the injected beam without prebunching. In the study of heavily loaded GeV inverse free electron lasers, we show that a majority of the power may be transferred from a laser to the accelerated electron beam. Reversing the process to decelerate high power electron beams, a mechanism we refer to as tapering enhanced stimulated superradiant amplification, offers a clear path to high power light sources. We present studies of radiation production for a wide range of wavelengths (10mum, 13nm, and 0.3nm) using this method and discuss the design for a deceleration experiment using the same undulator used

  15. Compressed sensing of roller bearing fault based on multiple down-sampling strategy

    NASA Astrophysics Data System (ADS)

    Wang, Huaqing; Ke, Yanliang; Luo, Ganggang; Tang, Gang

    2016-02-01

    Roller bearings are essential components of rotating machinery and are often exposed to complex operating conditions, which can easily lead to their failures. Thus, to ensure normal production and the safety of machine operators, it is essential to detect the failures as soon as possible. However, it is a major challenge to maintain a balance between detection efficiency and big data acquisition given the limitations of sampling theory. To overcome these limitations, we try to preserve the information pertaining to roller bearing failures using a sampling rate far below the Nyquist sampling rate, which can ease the pressure generated by the large-scale data. The big data of a faulty roller bearing’s vibration signals is firstly reduced by a down-sample strategy while preserving the fault features by selecting peaks to represent the data segments in time domain. However, a problem arises in that the fault features may be weaker than before, since the noise may be mistaken for the peaks when the noise is stronger than the vibration signals, which makes the fault features unable to be extracted by commonly-used envelope analysis. Here we employ compressive sensing theory to overcome this problem, which can make a signal enhancement and reduce the sample sizes further. Moreover, it is capable of detecting fault features from a small number of samples based on orthogonal matching pursuit approach, which can overcome the shortcomings of the multiple down-sample algorithm. Experimental results validate the effectiveness of the proposed technique in detecting roller bearing faults.

  16. Rereading "The Jack-Roller:" Hidden Histories in Sociology and Social Work

    ERIC Educational Resources Information Center

    Shaw, Ian

    2009-01-01

    I revisit one of the iconic Chicago School studies, Clifford Shaw's "The Jack-Roller". A naive reading of Shaw's book leaves the reader with a sense of having been inducted into a melange of what we now know as "sociology" and "social work," but which to Shaw seems a coherent stance. I suggest that this is close to the heart of how things were,…

  17. Optimization of Spherical Roller Bearing Design Using Artificial Bee Colony Algorithm and Grid Search Method

    NASA Astrophysics Data System (ADS)

    Tiwari, Rajiv; Waghole, Vikas

    2015-07-01

    Bearing standards impose restrictions on the internal geometry of spherical roller bearings. Geometrical and strength constraints conditions have been formulated for the optimization of bearing design. The long fatigue life is one of the most important criteria in the optimum design of bearing. The life is directly proportional to the dynamic capacity; hence, the objective function has been chosen as the maximization of dynamic capacity. The effect of speed and static loads acting on the bearing are also taken into account. Design variables for the bearing include five geometrical parameters: the roller diameter, the roller length, the bearing pitch diameter, the number of rollers, and the contact angle. There are a few design constraint parameters which are also included in the optimization, the bounds of which are obtained by initial runs of the optimization. The optimization program is made to run for different values of these design constraint parameters and a range of the parameters is obtained for which the objective function has a higher value. The artificial bee colony algorithm (ABCA) has been used to solve the constrained optimized problem and the optimum design is compared with the one obtained from the grid search method (GSM), both operating independently. Both the ABCA and the GSM have been finally combined together to reach the global optimum point. A constraint violation study has also been carried out to give priority to the constraint having greater possibility of violations. Optimized bearing designs show a better performance parameter with those specified in bearing catalogs. The sensitivity analysis of bearing parameters has also been carried out to see the effect of manufacturing tolerance on the objective function.

  18. On Calculation Methods and Results for Straight Cylindrical Roller Bearing Deflection, Stiffness, and Stress

    NASA Technical Reports Server (NTRS)

    Krantz, Timothy L.

    2011-01-01

    The purpose of this study was to assess some calculation methods for quantifying the relationships of bearing geometry, material properties, load, deflection, stiffness, and stress. The scope of the work was limited to two-dimensional modeling of straight cylindrical roller bearings. Preparations for studies of dynamic response of bearings with damaged surfaces motivated this work. Studies were selected to exercise and build confidence in the numerical tools. Three calculation methods were used in this work. Two of the methods were numerical solutions of the Hertz contact approach. The third method used was a combined finite element surface integral method. Example calculations were done for a single roller loaded between an inner and outer raceway for code verification. Next, a bearing with 13 rollers and all-steel construction was used as an example to do additional code verification, including an assessment of the leading order of accuracy of the finite element and surface integral method. Results from that study show that the method is at least first-order accurate. Those results also show that the contact grid refinement has a more significant influence on precision as compared to the finite element grid refinement. To explore the influence of material properties, the 13-roller bearing was modeled as made from Nitinol 60, a material with very different properties from steel and showing some potential for bearing applications. The codes were exercised to compare contact areas and stress levels for steel and Nitinol 60 bearings operating at equivalent power density. As a step toward modeling the dynamic response of bearings having surface damage, static analyses were completed to simulate a bearing with a spall or similar damage.

  19. Calculated and experimental data for a 118-mm bore roller bearing to 3 million DN

    NASA Technical Reports Server (NTRS)

    Coe, H. H.; Schuller, F. T.

    1980-01-01

    The operating characteristics for 118 mm bore cylindrical roller bearing are examined using the computer program CYBEAN. The predicted results of inner and outer-race temperatures and heat transferred to the lubricant generally compared well with experimental data for shaft speeds to 3 million DN (25,000 rpm), radial loads to 8900 N (2000 lb), and total lubricant flow rates to 0.0102 cu m/min (2.7 gal/min).

  20. Clinical use of centrifugal pumps and the roller pump in open heart surgery: a comparative evaluation.

    PubMed

    Yoshikai, M; Hamada, M; Takarabe, K; Okazaki, Y; Ito, T

    1996-06-01

    Centrifugal pumps have been used widely as the main pump in open heart surgery to reduce damage to blood elements and to reduce the activation of the coagulation system. The purpose of this study was the evaluation and comparison of the effects of two types of centrifugal pumps and of one type of roller pump on blood elements, the coagulation system, complements, and immunoglobulins. Two types of centrifugal pumps (Lifestream; St. Jude Medical, Chelmsford, Massachusetts; and BP-80: Medtronic, BioMedicus, Inc., Eden Prairie, Minnesota, U.S.A.) and one roller pump (Mera Co.) were used separately as the main pump for cardiopulmonary bypass (CPB) in 29 patients. Platelet counts, lactate dehydrogenase, antithrombin III, thrombin-antithrombin complex (TAT), complements (C3, C4, and CH50) and immunoglobulins G, A, and M values were measured before and after CPB and compared. Values, except those for TAT, showed no significant difference among the three groups. The TAT values increased less in each of the centrifugal pump groups than in the roller pump group. This finding suggests that thrombin synthesis might be suppressed by the use of a centrifugal pump.

  1. Effect of Silicon Nitride Balls and Rollers on Rolling Bearing Life

    NASA Technical Reports Server (NTRS)

    Zaretsky, Erwin V.; Vlcek, Brian L.; Hendricks, Robert C.

    2005-01-01

    Three decades have passed since the introduction of silicon nitride rollers and balls into conventional rolling-element bearings. For a given applied load, the contact (Hertz) stress in a hybrid bearing will be higher than an all-steel rolling-element bearing. The silicon nitride rolling-element life as well as the lives of the steel races were used to determine the resultant bearing life of both hybrid and all-steel bearings. Life factors were determined and reported for hybrid bearings. Under nominal operating speeds, the resultant calculated lives of the deep-groove, angular-contact, and cylindrical roller hybrid bearings with races made of post-1960 bearing steel increased by factors of 3.7, 3.2, and 5.5, respectively, from those calculated using the Lundberg-Palmgren equations. An all-steel bearing under the same load will have a longer life than the equivalent hybrid bearing under the same conditions. Under these conditions, hybrid bearings are predicted to have a lower fatigue life than all-steel bearings by 58 percent for deep-groove bearings, 41 percent for angular-contact bearings, and 28 percent for cylindrical roller bearings.

  2. Evaluation of a high-torque backlash-free roller actuator

    NASA Technical Reports Server (NTRS)

    Steinetz, Bruce M.; Rohn, Douglas A.; Anderson, William

    1986-01-01

    The results are presented of a test program that evaluated the stiffness, accuracy, torque ripple, frictional losses, and torque holding capability of a 16:1 ratio, 430 N-m (320 ft-lb) planetary roller drive for a potential space vehicle actuator application. The drive's planet roller supporting structure and bearings were found to be the largest contributors to overall drive compliance, accounting for more than half of the total. In comparison, the traction roller contacts themselves contributed only 9 percent of the drive's compliance based on an experimentally verified stiffness model. The drive exhibited no backlash although 8 arc sec of hysteresis deflection were recorded due to microcreep within the contact under torque load. Because of these load-dependent displacements, some form of feedback control would be required for arc second positioning applications. Torque ripple tests showed the drive to be extremely smooth, actually providing some damping of input torsional oscillations. The drive also demonstrated the ability to hold static torque with drifts of 7 arc sec or less over a 24 hr period at 35 percent of full load.

  3. Roller and Centrifugal Pumps: A Retrospective Comparison of Bleeding Complications in Extracorporeal Membrane Oxygenation.

    PubMed

    Halaweish, Ihab; Cole, Adam; Cooley, Elaine; Lynch, William R; Haft, Jonathan W

    2015-01-01

    Centrifugal pumps are increasingly used for extracorporeal membrane oxygenation (ECMO) rather than roller pumps. However, shear forces induced by these types of continuousflow pumps are associated with acquired von Willebrand factor deficiency and bleeding complications. This study was undertaken to compare adverse bleeding complications with the use of centrifugal and roller pumps in patients on prolonged ECMO support. The records of all adult ECMO patients from June 2002 to 2013 were retrospectively reviewed using the University of Michigan Health System database and the Extracorporeal Life Support Organization registry, focusing on patients supported for at least 5 days. Ninety-five ECMO patients met criteria for inclusion (48 roller vs. 47 centrifugal pump). Indications included pulmonary (79%), cardiac (15%), and extracorporeal cardiopulmonary resuscitation (6%), without significant difference between the two groups. Despite lower heparin anticoagulation (10.9 vs. 13.7 IU/kg/hr) with centrifugal pumps, there was a higher incidence of nonsurgical bleeding (gastrointestinal, pulmonary, and neurological) in centrifugal pump patients (26.1 vs. 9.0 events/1,000 patient-days, p = 0.024). In conclusion, in our historical comparison, despite reduced anticoagulation, ECMO support using centrifugal pumps was associated with a higher incidence of nonsurgical bleeding. The mechanisms behind this are multifactorial and require further investigation.

  4. Delta efficiency of uphill roller skiing with the double pole and diagonal stride techniques.

    PubMed

    Hoffman, M D; Clifford, P S; Watts, P B; O'Hagan, K P; Mittelstadt, S W

    1995-12-01

    Delta efficiencies for uphill roller skiing with the double pole (DP) and diagonal stride (DS) techniques were determined among 4 female and 4 male cross-country ski racers in order to examine for differences between techniques and between the sexes. Each skier roller-skied on a motorized ski-treadmill at 1.7% and 7.1% grades with both techniques at 2 to 4 different speeds. Steady-state oxygen uptake values were used to calculate the differences in metabolic requirements for roller skiing at the 2 grades (delta E). The differences in external work rates between the 2 grades (delta W) were calculated from the work rates for overcoming rolling resistance and elevating the transported mass against gravity. Delta efficiencies (delta W/ delta E) ranged from 14 to 36%, were significantly greater (p < 0.001) for DS than DP, and showed a significant (p < 0.01) velocity effect for DS. Delta efficiencies were 27% greater (p < 0.05) for the women compared with the men for DP, and significant (p < 0.05) correlations were found between efficiency for DP and body mass. This suggests that the higher efficiency with DP for female skiers is at least partially due to their lower body mass.

  5. Forces and mechanical energy fluctuations during diagonal stride roller skiing; running on wheels?

    PubMed

    Kehler, Alyse L; Hajkova, Eliska; Holmberg, Hans-Christer; Kram, Rodger

    2014-11-01

    Mechanical energy can be conserved during terrestrial locomotion in two ways: the inverted pendulum mechanism for walking and the spring-mass mechanism for running. Here, we investigated whether diagonal stride cross-country roller skiing (DIA) utilizes similar mechanisms. Based on previous studies, we hypothesized that running and DIA would share similar phase relationships and magnitudes of kinetic energy (KE), and gravitational potential energy (GPE) fluctuations, indicating elastic energy storage and return, as if roller skiing is like 'running on wheels'. Experienced skiers (N=9) walked and ran at 1.25 and 3 m s(-1), respectively, and roller skied with DIA at both speeds on a level dual-belt treadmill that recorded perpendicular and parallel forces. We calculated the KE and GPE of the center of mass from the force recordings. As expected, the KE and GPE fluctuated with an out-of-phase pattern during walking and an in-phase pattern during running. Unlike walking, during DIA, the KE and GPE fluctuations were in phase, as they are in running. However, during the glide phase, KE was dissipated as frictional heat and could not be stored elastically in the tendons, as in running. Elastic energy storage and return epitomize running and thus we reject our hypothesis. Diagonal stride cross-country skiing is a biomechanically unique movement that only superficially resembles walking or running.

  6. Design and Operating Characteristics of High-Speed, Small-Bore Cylindrical-Roller Bearings

    NASA Technical Reports Server (NTRS)

    Pinel, Stanley, I.; Signer, Hans R.; Zaretsky, Erwin V.

    2000-01-01

    The computer program SHABERTH was used to analyze 35-mm-bore cylindrical roller bearings designed and manufactured for high-speed turbomachinery applications. Parametric tests of the bearings were conducted on a high-speed, high-temperature bearing tester and the results were compared with the computer predictions. Bearings with a channeled inner ring were lubricated through the inner ring, while bearings with a channeled outer ring were lubricated with oil jets. Tests were run with and without outer-ring cooling. The predicted bearing life decreased with increasing speed because of increased contact stresses caused by centrifugal load. Lower temperatures, less roller skidding, and lower power losses were obtained with channeled inner rings. Power losses calculated by the SHABERTH computer program correlated reasonably well with the test results. The Parker formula for XCAV (used in SHABERTH as a measure of oil volume in the bearing cavity) needed to be adjusted to reflect the prevailing operating conditions. The XCAV formula will need to be further refined to reflect roller bearing lubrication, ring design, cage design, and location of the cage-controlling land.

  7. Feasibility study of a discrete bearing/roller drive rotary joint for the space station

    NASA Technical Reports Server (NTRS)

    Loewenthal, S. H.; Schuller, F. T.

    1986-01-01

    The most critical mechanism on board the proposed space station is the continously rotating joint which must accurately align the solar power units with the sun during earth orbit. The feasibility of a multiple, discrete bearing supported joint driven by a self-loading, pinch drive actuator was investigated for this application. This concept appears to offer greater protection against catastrophic jamming, less sensitivity to adverse thermal gradients, greater accessibility to inorbit servicing or replacement and greater adaptability to very large (5 m) truss members than to more conventional continuous support bearing/gear reducer joints. Analytical trade studies performed herein establish that a discrete cam roller bearing support system having eight hangers around a continuous ring would provide sufficient radial and bending stiffness to prevent any degradation in the fundamental frequencies of the solar wing structure. Furthermore, it appears that the pinch roller drive mechanism can be readily sized to meet or exceed system performance and service life requirements. Wear life estimates based on experimental data for a steel roller coated with an advanced polyimide film show a continuous service life more than two orders of magnitude greater than required for this application.

  8. Angiographic and procedural outcome after coronary angioplasty in high-risk subsets using a decremental diameter (tapered) balloon catheter. Tapered Balloon Registry Investigators.

    PubMed

    Laird, J R; Popma, J J; Knopf, W D; Yakubov, S; Satler, L; White, H; Bergelson, B; Hennecken, J; Lewis, S; Parks, J M; Holmes, D R

    1996-03-15

    The angiographic and clinical outcomes of 115 patients (129 lesions) treated at 11 clinical centers using a decremental diameter (tapered) balloon catheter were evaluated. The presence of marked tapering of the reference vessel, lesion location involving a bifurcation or anastomosis of a saphenous vein graft, or total coronary occlusion where estimation of the distal vessel size was difficult were indications for this device. The tapered balloon was used as the initial dilatation device in 62 patients (73 narrowings), and as a secondary device in 53 patients (56 narrowings). Lesions selected for tapered balloon angioplasty were generally complex (95% had > or = 1 and 60% had > or = 2 adverse morphologic features). Vessel diameters were larger in the proximal reference segments (3.07 +/- 0.52 mm) than in distal ones (2.48 +/- 0.45 mm) (p<0.001). After tapered balloon angioplasty, the minimal lumen diameter increased from 0.85 +/- 0.34 mm to 2.13 +/- 0.50 mm (p<0.001), and the percent diameter stenosis decreased from 69 +/- 12% to 24 +/- 12% (p<0.001). Coronary dissections occurred in 20% of lesions; they were severe in 4% (National Heart, Lung, and Blood Institute grade C to F). Abrupt closure occurred in 4.3% of patients (2.6% immediate; 1.7% delayed). Procedural success was obtained in 110 patients (96%); major complications (in-hospital death, myocardial infarction, or emergency coronary bypass surgery) occurred in 3 patients (2.7%). Coronary angioplasty using the tapered balloon catheter appears to be a safe and effective technique for the treatment of complex lesion subsets, particularly those involving coronary arteries with marked segmental tapering.

  9. The avian tectorial membrane: Why is it tapered?

    NASA Astrophysics Data System (ADS)

    Iwasa, Kuni H.; Ricci, Anthony J.

    2015-12-01

    While the mammalian- and the avian inner ears have well defined tonotopic organizations as well as hair cells specialized for motile and sensing roles, the structural organization of the avian ear is different from its mammalian cochlear counterpart. Presumably this difference stems from the difference in the way motile hair cells function. Short hair cells, whose role is considered analogous to mammalian outer hair cells, presumably depends on their hair bundles, and not motility of their cell body, in providing the motile elements of the cochlear amplifier. This report focuses on the role of the avian tectorial membrane, specifically by addressing the question, "Why is the avian tectorial membrane tapered from the neural to the abneural direction?"

  10. Development of SiC Large Tapered Crystal Growth

    NASA Technical Reports Server (NTRS)

    Neudeck, Phil

    2011-01-01

    Research Focus Area: Power Electronics, Temperature Tolerant Devices. Demonstrate initial feasibility of totally new "Large Tapered Crystal" (LTC) process for growing vastly improved large-diameter wide-band gap wafers. Addresses Targets: The goal of this research is to experimentally investigate and demonstrate feasibility of the key unproven LTC growth processes in SiC. Laser-assisted growth of long SiC fiber seeds. Radial epitaxial growth enlargement of seeds into large SiC boules. Uniqueness and Impacts open a new technology path to large-diameter SiC and GaN wafers with 1000-fold defect density improvement at 2-4 fold lower cost. Leapfrog improvement in wide band gap power device capability and cost.

  11. Thin-ribbon tapered coupler for dielectric waveguides

    NASA Technical Reports Server (NTRS)

    Yeh, C.; Otoshi, T. Y.; Shimabukuro, F. I.

    1994-01-01

    A recent discovery shows that a high-dielectric constant, low-loss, solid material can be made into a ribbon-like waveguide structure to yield an attenuation constant of less than 0.02 dB/m for single-mode guidance of millimeter/submillimeter waves. One of the crucial components that must be invented in order to guarantee the low-loss utilization of this dielectric-waveguide guiding system is the excitation coupler. The traditional tapered-to-a-point coupler for a dielectric rod waveguide fails when the dielectric constant of the dielectric waveguide is large. This article presents a new way to design a low-loss coupler for a high- or low-dielectric constant dielectric waveguide for millimeter or submillimeter waves.

  12. Improved finite-difference vibration analysis of pretwisted, tapered beams

    NASA Technical Reports Server (NTRS)

    Subrahmanyam, K. B.; Kaza, K. R. V.

    1984-01-01

    An improved finite difference procedure based upon second order central differences is developed. Several difficulties encountered in earlier works with fictitious stations that arise in using second order central differences, are eliminated by developing certain recursive relations. The need for forward or backward differences at the beam boundaries or other similar procedures is eliminated in the present theory. By using this improved theory, the vibration characteristics of pretwisted and tapered blades are calculated. Results of the second order theory are compared with published theoretical and experimental results and are found to be in good agreement. The present method generally produces close lower bound solutions and shows fast convergence. Thus, extrapolation procedures that are customary with first order finite-difference methods are unnecessary. Furthermore, the computational time and effort needed for this improved method are almost the same as required for the conventional first order finite-difference approach.

  13. Formation of discrete pulses using taper defects in photonic crystals

    NASA Astrophysics Data System (ADS)

    Balasubramanian, Sai Venkatesh

    2016-01-01

    A two-dimensional photonic crystal based on a lattice of silicon rods in air with a photonic bandgap in the visible and near-ultraviolet spectra is proposed by removing some of the silicon rods or resizing their radii to create a monotonically varying tapered line defect, thereby pertaining to a case of structure-based nonlinearity and making it possible to operate with low input powers. By properly manipulating the length of the line defect, pulse compression and consequent adiabatic amplification are seen, along with bunching/antibunching of pulses. For certain modes of operation, field confinement is observed, and this leads to the formation of discrete pulses, or light bullets. Such a structure can be used as a multifunctional device, with some of the functionalities being optical nonpumped amplification, frequency upconversion, memory writing, matched termination, and slow wave guiding, which form the major conclusions of the work.

  14. Tapered whiskers are required for active tactile sensation

    PubMed Central

    Hires, Samuel Andrew; Pammer, Lorenz; Svoboda, Karel; Golomb, David

    2013-01-01

    Many mammals forage and burrow in dark constrained spaces. Touch through facial whiskers is important during these activities, but the close quarters makes whisker deployment challenging. The diverse shapes of facial whiskers reflect distinct ecological niches. Rodent whiskers are conical, often with a remarkably linear taper. Here we use theoretical and experimental methods to analyze interactions of mouse whiskers with objects. When pushed into objects, conical whiskers suddenly slip at a critical angle. In contrast, cylindrical whiskers do not slip for biologically plausible movements. Conical whiskers sweep across objects and textures in characteristic sequences of brief sticks and slips, which provide information about the tactile world. In contrast, cylindrical whiskers stick and remain stuck, even when sweeping across fine textures. Thus the conical whisker structure is adaptive for sensor mobility in constrained environments and in feature extraction during active haptic exploration of objects and surfaces. DOI: http://dx.doi.org/10.7554/eLife.01350.001 PMID:24252879

  15. Growth strategies to control tapering in Ge nanowires

    NASA Astrophysics Data System (ADS)

    Periwal, P.; Baron, T.; Gentile, P.; Salem, B.; Bassani, F.

    2014-04-01

    We report the effect of PH3 on the morphology of Au catalyzed Ge nanowires (NWs). Ge NWs were grown on Si (111) substrate at 400 °C in the presence of PH3, using vapor-liquid-solid method by chemical vapor deposition. We show that high PH3/GeH4 ratio causes passivation at NW surface. At high PH3 concentration phosphorous atoms attach itself on NW surface and form a self-protection coating that prevents conformal growth and leads to taper free nanostructures. However, in case of low PH3 flux the combination of axial and radial growth mechanism occurs resulting in conical structure. We have also investigated axial PH3-intrinsic junctions in Ge NWs. The unusual NW shape is attributed to a combination of catalyzed, uncatalyzed and diffusion induced growth.

  16. Analysis of tapered front-coupling X-ray waveguides.

    PubMed

    Bukreeva, Inna; Pelliccia, Daniele; Cedola, Alessia; Scarinci, Fernando; Ilie, Mihaela; Giannini, Cinzia; De Caro, Liberato; Lagomarsino, Stefano

    2010-01-01

    The coupling and propagation of electromagnetic waves through planar X-ray waveguides (WG) with vacuum gap and Si claddings are analyzed in detail, starting from the source and ending at the detector. The general case of linearly tapered WGs (i.e. with the entrance aperture different from the exit one) is considered. Different kinds of sources, i.e. synchrotron radiation and laboratory desk-top sources, have been considered, with the former providing a fully coherent incoming beam and the latter partially coherent beams. It is demonstrated that useful information about the parameters of the WG can be derived, comparing experimental results with computer simulation based on analytical solutions of the Helmholtz equation which take into account the amplitude and phase matching between the standing waves created in front of the WG, and the resonance modes propagating into the WG.

  17. Free vibration analyses of generally laminated tapered skew plates

    NASA Astrophysics Data System (ADS)

    Kapania, Rakesh K.; Singhvi, Sarvesh

    1992-04-01

    An efficient method is developed for the free vibration analyses of generally laminated composite skew plates having arbitrary edge conditions, such as clamped, simply supported or free. The procedure consists of the Rayleigh-Ritz method utilizing a strain energy functional containing both bending and stretching effects and accommodating arbitrary ply stacking sequences. A set of Chebyshev polynomials is used as trial functions to represent the three components of the displacement at a given point. The geometric boundary conditions are satisfied by providing appropriate springs with large stiffnesses at a given edge. Results are obtained for isotropic, specially orthotropic, symmetrically laminated and unsymmetrically laminated plates. Both rectangular and skewed tapered plates are analyzed. The capability to perform the static analysis of a composite plate is also demonstrated. To establish the correctness and effectiveness of the method, whenever possible, the numerical results are compared with those obtained by other researchers.

  18. Growth strategies to control tapering in Ge nanowires

    SciTech Connect

    Periwal, P.; Baron, T. Salem, B.; Bassani, F.; Gentile, P.

    2014-04-01

    We report the effect of PH{sub 3} on the morphology of Au catalyzed Ge nanowires (NWs). Ge NWs were grown on Si (111) substrate at 400 °C in the presence of PH{sub 3}, using vapor-liquid-solid method by chemical vapor deposition. We show that high PH{sub 3}/GeH{sub 4} ratio causes passivation at NW surface. At high PH{sub 3} concentration phosphorous atoms attach itself on NW surface and form a self-protection coating that prevents conformal growth and leads to taper free nanostructures. However, in case of low PH{sub 3} flux the combination of axial and radial growth mechanism occurs resulting in conical structure. We have also investigated axial PH{sub 3}-intrinsic junctions in Ge NWs. The unusual NW shape is attributed to a combination of catalyzed, uncatalyzed and diffusion induced growth.

  19. Fabrication and characterization of multimaterial chalcogenide glass fiber tapers with high numerical apertures.

    PubMed

    Sun, Ya'nan; Dai, Shixun; Zhang, Peiqing; Wang, Xunsi; Xu, Yinsheng; Liu, Zijun; Chen, Feifei; Wu, Yuehao; Zhang, Yuji; Wang, Rongping; Tao, Guangming

    2015-09-01

    This paper reports on the fabrication and characterization of multimaterial chalcogenide fiber tapers that have high numerical apertures (NAs). We first fabricated multimaterial As(2)Se(3)-As(2)S(3) chalcogenide fiber preforms via a modified one-step coextrusion process. The preforms were drawn into multi- and single-mode fibers with high NAs (≈1.45), whose core/cladding diameters were 103/207 and 11/246 μm, respectively. The outer diameter of the fiber was tapered from a few hundred microns to approximately two microns through a self-developed automatic tapering process. Simulation results showed that the zero-dispersion wavelengths (ZDWs) of the tapers were shorter than 2 μm, indicating that the tapers can be conveniently pumped by commercial short wavelength infrared lasers. We also experimentally demonstrated the supercontinuum generation (SCG) in a 15-cm-long multimaterial As(2)Se(3)-As(2)S(3) chalcogenide taper with 1.9 μm core diameter and the ZDW was shifted to 3.3 μm. When pumping the taper with 100 fs short pulses at 3.4 µm, a 20 dB spectral of the generated supercontinuum spans from 1.5 μm to longer than 4.8 μm. PMID:26368447

  20. Inferring the spatial variation of the wedge strength based on a modified critical taper model

    NASA Astrophysics Data System (ADS)

    Yang, C.; Liu, H.; Hsieh, Y.; Dong, J.

    2013-12-01

    Critical taper wedge theory has been widely applied to evaluate the strength of the detachment fault and the wedge by measuring taper angle. Traditional taper model, which incorporated constant cohesion and friction angle, fails to explain the lateral variation of the taper angle. A modified critical taper model adopting nonlinear Hoek-Brown failure criterion is proposed accordingly. The fold-and-thrust belt of central Taiwan was studied. Based on the field works and laboratory tests, the geological strength index (GSI) and the uniaxial compressive strength were obtained and the wedge strength can be estimated accordingly. The GSI values from investigation are decreased from the west to the east along the cross section due to the wedge strength heterogeneity. The uniaxial compressive strength of intact rock varies from the age of formation and lithology. The estimated wedge strength exhibits a strong spatial variation. The strength of the detachment fault was derived from rotary shear tests using fault gouge materials under different velocities and normal stresses. General speaking, the steady-state friction coefficient are about 0.29-0.46 when the shear velocity less than 0.1 m/s. The friction coefficient is not sensitive to the normal stress. Consequently, the lateral variation of the taper angle, which calculated by modified critical taper model, is mainly dominated by the wedge strength heterogeneity and the thickening of the wedge from the west to the east.

  1. Effect of Taper Design on Trunnionosis in Metal on Polyethylene Total Hip Arthroplasty.

    PubMed

    Tan, Sok Chuen; Teeter, Matthew G; Del Balso, Christopher; Howard, James L; Lanting, Brent A

    2015-07-01

    This study examines how taper design affects corrosion and fretting at the head trunnion surface. All hip prostheses retrieved between 1999 and 2013 with 28mm/+0 heads were selected, resulting in 44 cobalt-chrome-on-polyethylene implants, representing six taper designs. Mean implantation time: 8.9±3.7years. The femoral head tapers were scored for fretting and corrosion using the Goldberg scale as both a combined score and by three zones (apex, central and base). There was no difference in age (P=0.34), BMI (P=0.29), or implantation time (P=0.19) between taper groups. The 11/13 taper had the highest combined corrosion and fretting score, but no difference (P=0.22) between groups for combined scores (P=0.22 for corrosion, P=0.19 for fretting). In a zone-specific analysis, the 11/13 taper had highest corrosion score at base zone (P=0.02). Taper design had a significant effect on corrosion at base of trunnion.

  2. Strain energy release rate analysis of delamination in a tapered laminate subjected to tension load

    NASA Technical Reports Server (NTRS)

    Salpekar, S. A.; Raju, I. S.; Obrien, T. K.

    1990-01-01

    A tapered composite laminate subjected to tension load was analyzed using the finite-element method. The glass/epoxy laminate has a (+ or - 45)sub 3 group of plies dropped in three distinct steps, each 20 ply-thicknesses apart, thus forming a taper angle of 5.71 degrees. Steep gradients of interlaminar normal and shear stress on a potential delamination interface suggest the existence of stress singularities at the points of material and geometric discontinuities created by the internal plydrops. The delamination was assumed to initiate at the thin end of the taper on a -45/+45 interface and the delamination growth was simulated in both directions, i.e., along the taper and into the thin region. The strain-energy-release rate for a delamination growing into the thin laminate consisted predominantly of mode I (opening) component. For a delamination growing along the tapered region, the strain-energy-release rate was initially all mode I, but the proportion of mode I decreased with increase in delamination size until eventually total G was all mode II. The total G for both delamination tips increased with increase in delamination size, indicating that a delamination initiating at the end of the taper will grow unstably along the taper and into the thin laminate simultaneously.

  3. Retention force of differently fabricated telescopic PEEK crowns with different tapers.

    PubMed

    Stock, Veronika; Wagner, Christina; Merk, Susanne; Roos, Malgorzata; Schmidlin, Patrick R; Eichberger, Marlis; Stawarczyk, Bogna

    2016-01-01

    To assess the retention force between primary and secondary PEEK crowns made by different fabrication methods. Primary crowns with different tapers (0°, 1°, and 2°) were fabricated and secondary crowns that were either milled from breCam BioHPP blanks, pressed from pellets (BioHPP Pellet) or granules (BioHPP Granulat) were produced. Each specimen was measured 20 times in a pulloff-test and results were analyzed using 2-/1-way ANOVA and linear regression analyses (p<0.05). Within 0° tapered crowns milled secondary crowns showed lower retention forces compared to pressed pellet crowns. Crowns with a 1° taper, however, showed no impact of the fabrication method on retention force. At a 2° taper, granular pressed crowns displayed lower values than their milled counterparts. Within the milled group, a 0° taper showed lower retention values than the higher tapers, whereas in the pressed groups, no impact of taper angle on retention force was found. PMID:27477224

  4. Wavelength-dependent femtosecond pulse amplification in wideband tapered-waveguide quantum well semiconductor optical amplifiers.

    PubMed

    Xia, Mingjun; Ghafouri-Shiraz, H

    2015-12-10

    In this paper, we study the wavelength-dependent amplification in three different wideband quantum well semiconductor optical amplifiers (QWAs) having conventional, exponentially tapered, and linearly tapered active region waveguide structures. A new theoretical model for tapered-waveguide QWAs considering the effect of lateral carrier density distribution and the strain effect in the quantum well is established based on a quantum well transmission line modeling method. The temporal and spectral characteristics of amplified femtosecond pulse are analyzed for each structure. It was found that, for the amplification of a single femtosecond pulse, the tapered-waveguide QWA provides higher saturation gain, and the output spectra of the amplified pulse in all three structures exhibit an apparent redshift and bandwidth narrowing due to the reduction of carrier density; however, the output spectrum in the tapered-waveguide amplifier is less distorted and exhibits smaller bandwidth narrowing. For the simultaneous amplification of two femtosecond pulses with different central frequencies, in all the three structures, two peaks appear in the output spectra while the peak at the frequency closer to the peak frequency of the QWA gain spectrum receives higher amplification due to the frequency (wavelength) dependence of the QWA gain. At a low peak power level of the input pulse, the bandwidth of each window in the tapered structure is larger than that of the conventional waveguide structure, which aggravates the spectrum alias in the amplification of femtosecond pulses with different central frequencies. As the peak powers of the two pulses increase, the spectrum alias in the conventional waveguide becomes more serious while there are small changes in the tapered structures. Also, we have found that in the amplification of a femtosecond pulse train, the linear-tapered QWAs exhibit the fastest gain recovery as compared with the conventional and exponentially tapered QWAs.

  5. Wavelength-dependent femtosecond pulse amplification in wideband tapered-waveguide quantum well semiconductor optical amplifiers.

    PubMed

    Xia, Mingjun; Ghafouri-Shiraz, H

    2015-12-10

    In this paper, we study the wavelength-dependent amplification in three different wideband quantum well semiconductor optical amplifiers (QWAs) having conventional, exponentially tapered, and linearly tapered active region waveguide structures. A new theoretical model for tapered-waveguide QWAs considering the effect of lateral carrier density distribution and the strain effect in the quantum well is established based on a quantum well transmission line modeling method. The temporal and spectral characteristics of amplified femtosecond pulse are analyzed for each structure. It was found that, for the amplification of a single femtosecond pulse, the tapered-waveguide QWA provides higher saturation gain, and the output spectra of the amplified pulse in all three structures exhibit an apparent redshift and bandwidth narrowing due to the reduction of carrier density; however, the output spectrum in the tapered-waveguide amplifier is less distorted and exhibits smaller bandwidth narrowing. For the simultaneous amplification of two femtosecond pulses with different central frequencies, in all the three structures, two peaks appear in the output spectra while the peak at the frequency closer to the peak frequency of the QWA gain spectrum receives higher amplification due to the frequency (wavelength) dependence of the QWA gain. At a low peak power level of the input pulse, the bandwidth of each window in the tapered structure is larger than that of the conventional waveguide structure, which aggravates the spectrum alias in the amplification of femtosecond pulses with different central frequencies. As the peak powers of the two pulses increase, the spectrum alias in the conventional waveguide becomes more serious while there are small changes in the tapered structures. Also, we have found that in the amplification of a femtosecond pulse train, the linear-tapered QWAs exhibit the fastest gain recovery as compared with the conventional and exponentially tapered QWAs. PMID

  6. Vector rectangular-shape laser based on reduced graphene oxide interacting with a long fiber taper.

    PubMed

    Gao, Lei; Zhu, Tao; Huang, Wei; Zeng, Jing

    2014-10-01

    A vector dual-wavelength rectangular-shape laser (RSL) based on a long fiber taper deposited with reduced graphene oxide is proposed, where nonlinearity is enhanced due to a large evanescent-field-interacting length and strong field confinement of an 8 mm fiber taper with a waist diameter of 4 μm. Graphene flakes are deposited uniformly on the taper waist with light pressure effect, so this structure guarantees both excellent saturable absorption and high nonlinearity. The RSL with a repetition rate of 7.9 MHz shows fast polarization switching in two orthogonal polarization directions, and temporal and spectral characteristics are investigated. PMID:25322232

  7. Adverse local tissue response lesion of the knee associated with Morse taper corrosion.

    PubMed

    McMaster, William C; Patel, Jay

    2013-02-01

    Modularity in arthroplasty components has increased options for solving complex issues in primary and revision procedures. However, this technology introduces the risk of accelerated metal ion release as a result of fretting or passive crevice corrosion within the Morse taper junction. Cobalt toxicity locally and systemically has been described with hip metal bearing surfaces and may be accentuated with ion release from Morse tapers. This is a case report of a knee adverse local tissue response lesion associated with corrosion within the Morse taper of a revision knee arthroplasty in the absence of systemic metal allergy.

  8. Quantification of the Contact Area at the Head-Stem Taper Interface of Modular Hip Prostheses

    PubMed Central

    Witt, Florian; Gührs, Julian; Morlock, Michael M.; Bishop, Nicholas E.

    2015-01-01

    Corrosion of modular taper junctions of hip implants may be associated with clinical failure. Taper design parameters, as well as the intraoperatively applied assembly forces, have been proposed to affect corrosion. Fretting corrosion is related to relative interface shear motion and fluid ingress, which may vary with contact force and area. It was hypothesised in this study that assembly forces modify the extent and distribution of the surface contact area at the taper interface between a cobalt chrome head and titanium stem taper with a standard threaded surface profile. Local abrasion of a thin gold coating applied to the stem taper prior to assembly was used to determine the contact area after disassembly. Profilometry was then used to assess permanent deformation of the stem taper surface profile. With increasing assembly force (500 N, 2000 N, 4000 N and 8000 N) the number of stem taper surface profile ridges in contact with the head taper was found to increase (9.2±9.3%, 65.4±10.8%, 92.8±6.0% and 100%) and the overall taper area in contact was also found to increase (0.6±0.7%, 5.5±1.0%, 9.9±1.1% and 16.1±0.9%). Contact was inconsistently distributed over the length of the taper. An increase in plastic radial deformation of the surface ridges (-0.05±0.14 μm, 0.1±0.14 μm, 0.21±0.22 μm and 0.96±0.25 μm) was also observed with increasing assembly force. The limited contact of the taper surface ridges at lower assembly forces may influence corrosion rates, suggesting that the magnitude of the assembly force may affect clinical outcome. The method presented provides a simple and practical assessment of the contact area at the taper interface. PMID:26280914

  9. Particle beam self-modulation instability in tapered and inhomogeneous plasma

    SciTech Connect

    Schroeder, Carl; Benedetti, Carlo; Esarey, Eric; Gruener, Florian; Leemans, Wim

    2011-12-28

    The particle beam self-modulation instability in tapered and inhomogeneous plasmas is analyzed via an evolution equation for the beam radius. For a sufficiently fast taper the instability is suppressed, and the condition for growth suppression is derived. The form of the taper to phase lock a trailing witness bunch in the plasma wave driven by a self-modulated beam is determined, which can increase the energy gain by several orders of magnitude. Growth of the instability places stringent constraints on the initial background plasma density fluctuations.

  10. Simulation on friction taper plug welding of AA6063-20Gr metal matrix composite

    NASA Astrophysics Data System (ADS)

    Hynes, N. Rajesh Jesudoss; Nithin, Abeyram M.

    2016-05-01

    Friction taper plug welding a variant of friction welding is useful in welding of similar and dissimilar materials. It could be used for joining of composites to metals in sophisticated aerospace applications. In the present work numerical simulation of friction taper plug welding process is carried out using finite element based software. Graphite reinforced AA6063 is modelled using the software ANSYS 15.0 and temperature distribution is predicted. Effect of friction time on temperature distribution is numerically investigated. When the friction time is increased to 30 seconds, the tapered part of plug gets detached and fills the hole in the AA6063 plate perfectly.

  11. Fusion splice between tapered inhibited coupling hypocycloid-core Kagome fiber and SMF.

    PubMed

    Zheng, Ximeng; Debord, Benoît; Vincetti, Luca; Beaudou, Benoît; Gérôme, Frédéric; Benabid, Fetah

    2016-06-27

    We report for the first time on tapering inhibited coupling (IC) hypocycloid-core shape Kagome hollow-core photonic crystal fibers whilst maintaining their delicate core-contour negative curvature with a down-ratio as large as 2.4. The transmission loss of down-tapered sections reaches a figure as low as 0.07 dB at 1550 nm. The tapered IC fibers are also spliced to standard SMF with a total insertion loss of 0.48 dB. These results show that all-fiber photonic microcells with the ultra-low loss hypocycloid core-contour Kagome fibers is now possible.

  12. Quantification of the Contact Area at the Head-Stem Taper Interface of Modular Hip Prostheses.

    PubMed

    Witt, Florian; Gührs, Julian; Morlock, Michael M; Bishop, Nicholas E

    2015-01-01

    Corrosion of modular taper junctions of hip implants may be associated with clinical failure. Taper design parameters, as well as the intraoperatively applied assembly forces, have been proposed to affect corrosion. Fretting corrosion is related to relative interface shear motion and fluid ingress, which may vary with contact force and area. It was hypothesised in this study that assembly forces modify the extent and distribution of the surface contact area at the taper interface between a cobalt chrome head and titanium stem taper with a standard threaded surface profile. Local abrasion of a thin gold coating applied to the stem taper prior to assembly was used to determine the contact area after disassembly. Profilometry was then used to assess permanent deformation of the stem taper surface profile. With increasing assembly force (500 N, 2000 N, 4000 N and 8000 N) the number of stem taper surface profile ridges in contact with the head taper was found to increase (9.2±9.3%, 65.4±10.8%, 92.8±6.0% and 100%) and the overall taper area in contact was also found to increase (0.6±0.7%, 5.5±1.0%, 9.9±1.1% and 16.1±0.9%). Contact was inconsistently distributed over the length of the taper. An increase in plastic radial deformation of the surface ridges (-0.05±0.14 μm, 0.1±0.14 μm, 0.21±0.22 μm and 0.96±0.25 μm) was also observed with increasing assembly force. The limited contact of the taper surface ridges at lower assembly forces may influence corrosion rates, suggesting that the magnitude of the assembly force may affect clinical outcome. The method presented provides a simple and practical assessment of the contact area at the taper interface. PMID:26280914

  13. Strain sensitivity control of fiber Bragg grating structures with fused tapers.

    PubMed

    Frazão, Orlando; Silva, Susana F O; Guerreiro, Ariel; Santos, José L; Ferreira, Luis A; Araújo, Francisco M

    2007-12-20

    We report on the analysis and experimental validation of the strain sensitivity dependences of a fiber Bragg grating written in standard optical fiber when combined with fused tapers. By controlling the difference between the cross sections of the fused taper and the Bragg grating, the strain sensitivity of the Bragg wavelength can be changed by acting on the gauge length. The strain sensing characteristics of an interferometric structure formed by fabricating a fused taper in the middle of a fiber Bragg grating are also reported. PMID:18091967

  14. The universal method for optimization of undulator tapering in FEL amplifiers

    NASA Astrophysics Data System (ADS)

    Schneidmiller, E. A.; Yurkov, M. V.

    2015-05-01

    Technique of undulator tapering in the post-saturation regime is used at the existing x-ray FELs for increasing the radiation power. There are also discussions on the future of high peak and average power FELs for scientific and industrial applications. Diffraction effects essentially influence on the choice of the tapering strategy. Recent studies resulted in an general law of the undulator tapering for a seeded FEL amplifier. In this paper we extend these results for the case of the Self Amplified Spontaneous Emission (SASE) FEL.

  15. High-power pulsed-current-mode operation of an overdriven tapered amplifier.

    PubMed

    Takase, Ken; Stockton, John K; Kasevich, Mark A

    2007-09-01

    We experimentally investigate the performance of a commercial tapered amplifier diode operating in a pulsed-current mode with a peak current that is significantly higher than the specified maximum continuous current. For a tapered amplifier rated at 500 mW of continuous power, we demonstrate 2.6 W of peak optical output power with 15 mW of injection light for 200 micros, 7 A current pulses. Different failure mechanisms for the tapered amplifier, including thermal and optical damage, are identified under these conditions. PMID:17767324

  16. The hydrodynamics of a wave-power device in a tapered harbor

    SciTech Connect

    Gallachoir, B.P.O.; Thomas, G.P.; Sarmento, A.J.N.A.

    1995-12-31

    This paper considers the hydrodynamic performance of a single wave-power device placed at the end of a tapered harbor and set in a reflecting coastline. A relatively simple model, in which the harbor width is assumed to be much smaller than the incident wavelength, is used to calculate approximate values for the hydrodynamic coefficients and hence determine the energy absorbing capabilities of the device. A comparison is presented between a device in a rectangular harbor and one in a tapered harbor in order to make a preliminary assessment of the influence of the taper.

  17. Riccati parameterized self-similar waves in tapered graded-index waveguides

    NASA Astrophysics Data System (ADS)

    Goyal, Amit; Gupta, Rama; Loomba, Shally; Kumar, C. N.

    2012-10-01

    We present a large family of self-similar waves by tailoring the tapering function, through Riccati parameter, in a tapered graded-index nonlinear waveguide amplifier. We show the existence of bright similaritons, self-similar Akhmediev breathers and self-similar rogue waves for generalized nonlinear Schrödinger equation with constant dispersion and nonlinearity, and a distributed gain. We illustrate the procedure to amplify the intensity of self-similar waves using isospectral Hamiltonian approach. This approach provides a handle to find analytically a wide class of tapering function and thus enabling one to control the self-similar wave structure and dynamical behavior.

  18. A Numerical Algorithm for Determining the Contact Stress of Circular Crowned Roller Compressed between Two Flat Plates

    NASA Astrophysics Data System (ADS)

    Horng, Thin-Lin

    The main purpose of this paper is to explore a numerical algorithm for determining the contact stress when a circular crowned roller is compressed between two plates. To start with, the deformation curve on a plate surface will be derived by using the contact mechanical model. Then, the contact stress distribution along the roller which occurs on the plate surface is divided into three parts: from the center of contact to the edge, the edge and apart from the contact line. The first part is calculated by the elastic contact theorem for the contact subjected to nominal stress between non-crowned parts of roller and plates, the second part is obtained by the classical Hertzian contact solution for the contact between crowned parts of roller and plates, and the third part is simulated as exponential decay. In order to overcome the defect of the half space theorem, in which a plate with infinite thickness is assumed initially, a weighting method is introduced to find the contact stress of the plate with finite thickness. Comparisons with various finite element results indicate that the algorithm for estimating the contact stress of a circular crowned roller compressed between two plates derived in this paper can be a reasonably accurate when a heavy displacement load is applied. This is because the contact area is large under a heavy load, and the effect of stress concentration is smaller in comparison with the case under a light load.

  19. Fabrication of a roller type PDMS stamp using SU-8 concave molds and its application for roll contact printing

    NASA Astrophysics Data System (ADS)

    Park, Jongho; Kim, Beomjoon

    2016-03-01

    Continuous fabrication of micropatterns at low-cost is attracting attention in various applications within industrial fields. To meet such demands, we have demonstrated a roll contact printing technique, using roller type polydimethylsiloxane (PDMS) stamps with roll-to-flat and roll-to-roll stages. Roller type PDMS stamps for roll contact printing were fabricated using a custom-made metal support and SU-8 microstructures fabricated on concave substrates as a mold. The molding/casting method which we developed here provided faster and easier fabrication than conventional methods for roller type stamps. Next, roll contact printing was performed using fabricated roller type PDMS stamps with roll-to-flat and roll-to-roll stages. Patterns with minimum widths of 3 μm and 2.1 μm were continuously fabricated for each stage, respectively. In addition, the relationship between applied pressures and dimensional changes of roll contact printed patterns was investigated. Finally, we confirmed that roll contact printing and the new fabrication method for roller stamps presented in this study demonstrated the feasibility for industrial applications.

  20. A new computational fluid dynamics method for in-depth investigation of flow dynamics in roller pump systems.

    PubMed

    Zhou, Xiaoming; Liang, Xin M; Zhao, Gang; Su, Youchao; Wang, Yang

    2014-07-01

    Roller pumps are commonly used in circulatory assist devices to deliver blood, but the inherent high mechanical stresses (especially wall shear stress) may cause considerable damage to cells. Conventional experimental approaches to evaluate and reduce device-induced cell damage require considerable effort and resources. In this work, we describe the use of a new computational fluid dynamics method to more effectively study roller pump systems. A generalized parametric model for the fluid field in a typical roller pump system is presented first, and analytical formulations of the moving boundary are then derived. Based on the model and formulations, the dynamic geometry and mesh of the fluid field can be updated automatically according to the time-dependent roller positions. The described method successfully simulated the pulsing flow generated by the pump, offering a convenient way to visualize the inherent flow pattern and to assess shear-induced cell damage. Moreover, the highly reconfigurable model and the semiautomated simulation process extend the usefulness of the presented method to a wider range of applications. Comparison studies were conducted, and valuable indications about the detailed effects of structural parameters and operational conditions on the produced wall shear stress were obtained. Given the good consistency between the simulated results and the existing experimental data, the presented method displays promising potential to more effectively guide the development of improved roller pump systems which produce less mechanical damage to cells.