Science.gov

Sample records for a537 carbon steel

  1. POTENTIAL FOR STRESS CORROSION CRACKING OF A537 CARBON STEEL NUCLEAR WASTE TANKS CONTAINING HIGHLY CAUSTIC SOLUTIONS

    SciTech Connect

    Lam, P.; Stripling, C.; Fisher, D.; Elder, J.

    2010-04-26

    The evaporator recycle streams of nuclear waste tanks may contain waste in a chemistry and temperature regime that exceeds the current corrosion control program, which imposes temperature limits to mitigate caustic stress corrosion cracking (CSCC). A review of the recent service history found that two of these A537 carbon steel tanks were operated in highly concentrated hydroxide solution at high temperature. Visual inspections, experimental testing, and a review of the tank service history have shown that CSCC has occurred in uncooled/un-stress relieved tanks of similar construction. Therefore, it appears that the efficacy of stress relief of welding residual stress is the primary corrosion-limiting mechanism. The objective of this experimental program is to test A537 carbon steel small scale welded U-bend specimens and large welded plates (30.48 x 30.38 x 2.54 cm) in a caustic solution with upper bound chemistry (12 M hydroxide and 1 M each of nitrate, nitrite, and aluminate) and temperature (125 C). These conditions simulate worst-case situations in these nuclear waste tanks. Both as-welded and stress-relieved specimens have been tested. No evidence of stress corrosion cracking was found in the U-bend specimens after 21 days of testing. The large plate test was completed after 12 weeks of immersion in a similar solution at 125 C except that the aluminate concentration was reduced to 0.3 M. Visual inspection of the plate revealed that stress corrosion cracking had not initiated from the machined crack tips in the weld or in the heat affected zone. NDE ultrasonic testing also confirmed subsurface cracking did not occur. Based on these results, it can be concluded that the environmental condition of these tests was unable to develop stress corrosion cracking within the test periods for the small welded U-bends and for the large plates, which were welded with an identical procedure as used in the construction of the actual nuclear waste tanks in the 1960s. The

  2. INVESTIGATION OF THE POTENTIAL FOR CAUSTIC STRESS CORROSION CRACKING OF A537 CARBON STEEL NUCLEAR WASTE TANKS

    SciTech Connect

    Lam, P.

    2009-10-15

    The evaporator recycle streams contain waste in a chemistry and temperature regime that may be outside of the current waste tank corrosion control program, which imposes temperature limits to mitigate caustic stress corrosion cracking (CSCC). A review of the recent service history (1998-2008) of Tanks 30 and 32 showed that these tanks were operated in highly concentrated hydroxide solution at high temperature. Visual inspections, experimental testing, and a review of the tank service history have shown that CSCC has occurred in uncooled/un-stress relieved F-Area tanks. Therefore, for the Type III/IIIA waste tanks the efficacy of the stress relief of welding residual stress is the only corrosion-limiting mechanism. The objective of this experimental program is to test carbon steel small scale welded U-bend specimens and large welded plates (12 x 12 x 1 in.) in a caustic solution with upper bound chemistry (12 M hydroxide and 1 M each of nitrate, nitrite, and aluminate) and temperature (125 C). These conditions simulate worst-case situations in Tanks 30 and 32. Both as-welded and stress-relieved specimens have been tested. No evidence of stress corrosion cracking was found in the U-bend specimens after 21 days of testing. The large plate test is currently in progress, but no cracking has been observed after 9 weeks of immersion. Based on the preliminary results, it appears that the environmental conditions of the tests are unable to develop stress corrosion cracking within the duration of these tests.

  3. Cyclic Polarization Behavior of ASTM A537-Cl.1 Steel in the Vapor Space Above Simulated Waste

    SciTech Connect

    Wiersma, B

    2004-11-01

    An assessment of the potential degradation mechanisms of Types I and II High-Level Waste (HLW) Tanks determined that pitting corrosion and stress corrosion cracking were the two most significant degradation mechanisms. Specifically, nitrate induced stress corrosion cracking was determined to be the principal degradation mechanism for the primary tank steel of non-stress relieved tanks. Controls on the solution chemistry have been in place to preclude the initiation and propagation of degradation in the tanks. However, recent experience has shown that steel not in contact with the bulk waste solution or slurry, but exposed to the ''vapor space'' above the bulk waste, may be vulnerable to the initiation and propagation of degradation, including pitting and stress corrosion cracking. A program to resolve the issues associated with potential vapor space corrosion is in place. The objective of the program is to develop understanding of vapor space (VSC) and liquid/air interface (LAIC) corrosion to ensure a defensible technical basis to provide accurate corrosion evaluations with regard to vapor space and liquid/air interface corrosion (similar to current evaluations). There are several needs for a technically defensible basis with sufficient understanding to perform these evaluations. These include understanding of the (1) surface chemistry evolution, (2) corrosion response through coupon testing, and (3) mechanistic understanding through electrochemical studies. Experimentation performed in FY02 determined the potential for vapor space and liquid/air interface corrosion of ASTM A285-70 and ASTM A537-Cl.1 steels. The material surface characteristics, i.e. mill-scale, polished, were found to play a key role in the pitting response. The experimentation indicated that the potential for limited vapor space and liquid/air interface pitting exists at 1.5M nitrate solution when using chemistry controls designed to prevent stress corrosion cracking. Experimentation performed in

  4. Electrochemical Studies of Nitrate-Induced Pitting in Carbon Steel

    SciTech Connect

    Zapp, P.E.

    1998-12-07

    The phenomenon of pitting in carbon steel exposed to alkaline solutions of nitrate and chloride was studied with the cyclic potentiodynamic polarization technique. Open-circuit and pitting potentials were measured on specimens of ASTM A537 carbon steel in pH 9.73 salt solutions at 40 degrees Celsius, with and without the inhibiting nitrite ion present. Nitrate is not so aggressive a pitting agent as is chloride. Both nitrate and chloride did induce passive breakdown and pitting in nitrite-free solutions, but the carbon steel retained passivity in solutions with 0.11-M nitrite even at a nitrate concentration of 2.2 M.

  5. Fatigue and Fracture-Toughness Characterization of SAW and SMA A537 Class I Ship-Steel Weldments.

    DTIC Science & Technology

    1981-12-01

    Mr. W. N. lannan Mr. Thomas W. Allen Vice President Chief Engineering Officer American Bureau of Shipping Military Se~lift Comand LCdr D. A. Anderson...Dynamics Ship Steel Improvement Program," General Dynamics, Quincey Ship- Building Division, May 17, 1977. 8 0 c" 041L on 0 1 ) 0 0 OD -4 0f C 0 0 0)C; C

  6. Prediction equations for corrosion rates of a A-537 and A-516 steels in Double Shell Slurry, Future PUREX, and Hanford Facilities Wastes

    SciTech Connect

    Divine, J.R.; Bowen, W.M.; Mackey, D.B.; Bates, D.J.; Pool, K.H.

    1985-06-01

    Even though the interest in the corrosion of radwaste tanks goes back to the mid-1940's when waste storage was begun, and a fair amount of corrosion work has been done since then, the changes in processes and waste types have outpaced the development of new data pertinent to the new double shell tanks. As a consequence, Pacific Northwest Laboratory (PNL) began a development of corrosion data on a broad base of waste compositions in 1980. The objective of the program was to provide operations personnel with corrosion rate data as a function of waste temperature and composition. The work performed in this program examined A-537 tank steel in Double Shell Slurry and Future PUREX Wastes, at temperatures between 40 and 180/sup 0/C as well as in Hanford Facilities Waste at 25 and 50/sup 0/C. In general, the corrosion rates were less than 1 mpy (0.001 in./y) and usually less than 0.5 mpy. Excessive corrosion rates (>1 mpy) were only found in dilute waste compositions or in concentrated caustic compositions at temperatures above 140/sup 0/C. Stress corrosion cracking was only observed under similar conditions. The results are presented as polynomial prediction equations with examples of the output of existing computer codes. The codes are not provided in the text but are available from the authors. 12 refs., 5 figs., 19 tabs.

  7. Ultrahigh carbon steels, Damascus steels, and superplasticity

    SciTech Connect

    Sherby, O.D.; Wadsworth, J.

    1997-04-01

    The processing properties of ultrahigh carbon steels (UHCSs) have been studied at Stanford University over the past twenty years. These studies have shown that such steels (1 to 2.1% C) can be made superplastic at elevated temperature and can have remarkable mechanical properties at room temperature. It was the investigation of these UHCSs that eventually brought us to study the myths, magic, and metallurgy of ancient Damascus steels, which in fact, were also ultrahigh carbon steels. These steels were made in India as castings, known as wootz, possibly as far back as the time of Alexander the Great. The best swords are believed to have been forged in Persia from Indian wootz. This paper centers on recent work on superplastic UHCSs and on their relation to Damascus steels. 32 refs., 6 figs.

  8. History of ultrahigh carbon steels

    SciTech Connect

    Wadsworth, J.; Sherby, O.D.

    1997-06-20

    The history and development of ultrahigh carbon steels (i.e., steels containing between 1 and 2.l percent C and now known as UHCS) are described. The early use of steel compositions containing carbon contents above the eutectoid level is found in ancient weapons from around the world. For example, both Damascus and Japanese sword steels are hypereutectoid steels. Their manufacture and processing is of interest in understanding the role of carbon content in the development of modern steels. Although sporadic examples of UHCS compositions are found in steels examined in the early part of this century, it was not until the mid-1970s that the modern study began. This study had its origin in the development of superplastic behavior in steels and the recognition that increasing the carbon content was of importance in developing that property. The compositions that were optimal for superplasticity involved the development of steels that contained higher carbon contents than conventional modern steels. It was discovered, however, that the room temperature properties of these compositions were of interest in their own right. Following this discovery, a period of intense work began on understanding their manufacture, processing, and properties for both superplastic forming and room temperature applications. The development of superplastic cast irons and iron carbides, as well as those of laminated composites containing UHCS, was an important part of this history.

  9. Inhibiting pitting corrosion in carbon steel exposed to dilute radioactive waste slurries

    SciTech Connect

    Zapp, P.E.; Hobbs, D.T.

    1991-01-01

    Dilute caustic high-level radioactive waste slurries can induce pitting corrosion in carbon steel. Cyclic potentiodynamic polarization tests were conducted in simulated and actual waste solutions to determine minimum concentrations of sodium nitrate which inhibit pitting in ASTM A537 class 1 steel exposed to these solutions. Susceptibility to pitting was assessed through microscopic inspection of specimens and inspection of polarization scans. Long-term coupon immersion tests were conducted to verify the nitrite concentrations established by the cyclic potentiodynamic polarization tests. The minimum effective nitrite concentration is expressed as a function of the waste nitrate concentration and temperature.

  10. Ultrahigh Carbon Steel.

    DTIC Science & Technology

    1984-10-01

    ferrite grains, 0.5-2 pm, containing fine spheroidized cementite particles, they have been shown not only to be super - plastic at intermediate...utilized to prepare ferrous laminated composites with super - plastic properties at intermediate temperatures’ 19 Ŗ 1 and with very high impact resistance...as an alloying addition that could alter the super - plastic properties of UHC steels because of its influence on the thermodynam- ics of the Fe-C

  11. Light microscopy of carbon steels

    SciTech Connect

    Samuels, L.E.

    1998-12-31

    Containing over 1,200 representative micrographs and the information and explanatory text that makes them really useful: composition, condition, etchant, and magnification, and more than 100 graphs and tables, this how to book not only gives everyday working examples, but also discusses the relationship between the constitution, metallurgy, and microstructure of various carbon steel products. Written by a renowned expert in metallography, this definitive work is a must for all those working in this area. Contents include: nomenclature of phases and constituents; phase transformations; low-carbon irons and steels; annealing and normalizing; spheroidization and graphitization; austenitization; transformation of austenite; tempering of martensite; welding; surface oxidation, decarburation; and oxidation scaling; glossary of terms; etching methods; conversion tables.

  12. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 2 2011-10-01 2011-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  13. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 2 2013-10-01 2013-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  14. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 2 2012-10-01 2012-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  15. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 2 2014-10-01 2014-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  16. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  17. Precise carbon control of fabricated stainless steel

    DOEpatents

    Nilsen, R.J.

    1975-12-01

    A process is described for controlling the carbon content of fabricated stainless steel components including the steps of heat treating the component in hydrogen atmospheres of varying dewpoints and carbon potentials.

  18. Connections: Superplasticity, Damascus Steels, Laminated Steels, and Carbon Dating

    NASA Astrophysics Data System (ADS)

    Wadsworth, Jeffrey

    2016-12-01

    In this paper, a description is given of the connections that evolved from the initial development of a family of superplastic plain carbon steels that came to be known as Ultra-High Carbon Steels (UHCS). It was observed that their very high carbon contents were similar, if not identical, to those of Damascus steels. There followed a series of attempts to rediscover how the famous patterns found on Damascus steels blades were formed. At the same time, in order to improve the toughness at room temperature of the newly-developed UHCS, laminated composites were made of alternating layers of UHCS and mild steel (and subsequently other steels and other metals). This led to a study of ancient laminated composites, the motives for their manufacture, and the plausibility of some of the claims relating to the number of layers in the final blades. One apparently ancient laminated composite, recovered in 1837 from the great pyramid of Giza which was constructed in about 2750 B.C., stimulated a carbon dating study of ancient steels. The modern interest in "Bladesmithing" has connections back to many of these ancient weapons.

  19. Tubercles and Localized Corrosion on Carbon Steel

    DTIC Science & Technology

    2010-12-01

    with symbiotic relationships and nutrient cycling. Miller and Tiller [14] indicated, "iron bacteria , which, together with the ferric hydroxide...conclude localized corrosion directly under the tubercles or a role for bacteria in their formation. 15. SUBJECT TERMS tubercle, carbon steel... bacteria in their formation. Introduction It is well established that tubercles formed on austenitic 300 series (304 or 316) stainless steel in

  20. Ultrahigh Ductility, High-Carbon Martensitic Steel

    NASA Astrophysics Data System (ADS)

    Qin, Shengwei; Liu, Yu; Hao, Qingguo; Zuo, Xunwei; Rong, Yonghua; Chen, Nailu

    2016-10-01

    Based on the proposed design idea of the anti-transformation-induced plasticity effect, both the additions of the Nb element and pretreatment of the normalization process as a novel quenching-partitioning-tempering (Q-P-T) were designed for Fe-0.63C-1.52Mn-1.49Si-0.62Cr-0.036Nb hot-rolled steel. This high-carbon Q-P-T martensitic steel exhibits a tensile strength of 1890 MPa and elongation of 29 pct accompanied by the excellent product of tensile and elongation of 55 GPa pct. The origin of ultrahigh ductility for high-carbon Q-P-T martensitic steel is revealed from two aspects: one is the softening of martensitic matrix due to both the depletion of carbon in the matensitic matrix during the Q-P-T process by partitioning of carbon from supersaturated martensite to retained austenite and the reduction of the dislocation density in a martensitic matrix by dislocation absorption by retained austenite effect during deformation, which significantly enhances the deformation ability of martensitic matrix; another is the high mechanical stability of considerable carbon-enriched retained austenite, which effectively reduces the formation of brittle twin-type martensite. This work verifies the correctness of the design idea of the anti-TRIP effect and makes the third-generation advanced high-strength steels extend to the field of high-carbon steels from low- and medium-carbon steels.

  1. Spheroidizing of medium carbon steels

    NASA Astrophysics Data System (ADS)

    O'Brien, James Michael

    2000-11-01

    An investigation has been made of spheroidization of medium carbon steels used in the bolt industry. Two process cycles were considered. One was the intercritical cycle, widely used in industry, in which the steel was heated above the A1 temperature for approximately 2 hours and then cooled to 688°C (1270°F) and held for various periods. The other was a subcritical cycle that involved heating to 704°C (1300°F) for various times. Wire samples were 0.4-in. diameter AISI 1541, considered high in manganese and difficult to spheroidize. Although AISI 4037 is considered easier to spheroidize, this alloy was also tested due to its extensive industrial use. It was found that the intercritical cycle produced a somewhat faster drop in hardness. However, one hour of the subcritical cycle yielded greater ductility than 32 hours of the intercritical process, as measured by tensile tests. Similar ductility results were achieved using a new flare test. The level of spheroidization was defined in this study to be the percentage of carbide particles with aspect ratios less than 3. The subcritical cycle produced the same level of spheroidization in 1/2 hour as that reached by the intercritical cycle in 32 hours. Faster spheroidization of cementite plates in the subcritical process appears to be due to the fine pearlite generated by the current practice of rapid cooling off the hot mill. This advantage is lost in the intercritical process because the original pearlite is dissolved above the A1 temperature.

  2. High strength, high ductility low carbon steel

    DOEpatents

    Koo, Jayoung; Thomas, Gareth

    1978-01-01

    A high strength, high ductility low carbon steel consisting essentially of iron, 0.05-0.15 wt% carbon, and 1-3 wt% silicon. Minor amounts of other constituents may be present. The steel is characterized by a duplex ferrite-martensite microstructure in a fibrous morphology. The microstructure is developed by heat treatment consisting of initial austenitizing treatment followed by annealing in the (.alpha. + .gamma.) range with intermediate quenching.

  3. Microbial-Influenced Corrosion of Corten Steel Compared with Carbon Steel and Stainless Steel in Oily Wastewater by Pseudomonas aeruginosa

    NASA Astrophysics Data System (ADS)

    Mansouri, Hamidreza; Alavi, Seyed Abolhasan; Fotovat, Meysam

    2015-07-01

    The microbial corrosion behavior of three important steels (carbon steel, stainless steel, and Corten steel) was investigated in semi petroleum medium. This work was done in modified nutrient broth (2 g nutrient broth in 1 L oily wastewater) in the presence of Pseudomonas aeruginosa and mixed culture (as a biotic media) and an abiotic medium for 2 weeks. The behavior of corrosion was analyzed by spectrophotometric and electrochemical methods and at the end was confirmed by scanning electron microscopy. The results show that the degree of corrosion of Corten steel in mixed culture, unlike carbon steel and stainless steel, is less than P. aeruginosa inoculated medium because some bacteria affect Corten steel less than other steels. According to the experiments, carbon steel had less resistance than Corten steel and stainless steel. Furthermore, biofilm inhibits separated particles of those steels to spread to the medium; in other words, particles get trapped between biofilm and steel.

  4. Graphitization in high carbon commercial steels

    NASA Astrophysics Data System (ADS)

    Neri, M. A.; Colás, R.; Valtierra, S.

    1998-08-01

    Graphitization kinetics in two commercial high carbon steels, AISI types 1075 and 1095, are studied by conducting a series of isothermal annealing treatments in the temperature range of 560 to 680‡ C for periods of time ranging from 20 to 500 h. The samples selected were collected along the processing route in a commercial production line dedicated to the fabrication of thin strip. The structures studied were those of hot rolling (consisting of fine pearlite), cold rolling (spheroidized carbides within a deformed ferritic matrix), and subcritical annealing (spheroidized carbides in undeformed ferrite). The samples obtained from hot rolled coils do not graphitize, whereas those cold rolled graphitize at a rate that depends on the type of steel and degree of deformation. No graphite was found in samples from the lower carbon steel, which were subcritically annealed, although they were observed in specimens from the other steel, which were cold rolled to a reduction of 50% prior to the subcritical annealing.

  5. Ultrahigh Carbon Steels and Their Laminates

    DTIC Science & Technology

    1990-02-01

    PROGRAM PROJECT TASK WORK UNIT 11LitME NT NO. No. NO. NO I I TITLE tiAtluda Seca.r.ty Ck~iaialasonJ Ultrahigh Carbon Steels and their laminates...PROM Aug. 1984 To- Fe~r--9O February 1, 1906 1S. SUPPLEMENTARY NOTATION Amore coinpetc tte of tie-program is: Low Density and Tough Steels with High...Hardenabihzty: Processing, Testing and Evaluation of UHC steels and their laminates 17 COSATI CODES Is.. SUBJECT TERMS (CoAtInai" on uvwrue iroleemary

  6. Tests Of Protective Coats For Carbon Steel

    NASA Technical Reports Server (NTRS)

    Macdowell, Louis G., III

    1995-01-01

    Report describes laboratory and field tests of candidate paints (primers, tie coats, and topcoats) for use in protecting carbon-steel structures against corrosion in seaside environment at Kennedy Space Center. Coating materials selected because of utility in preventing corrosion, also on basis of legal requirements, imposed in several urban areas, for reduction of volatile organic contents.

  7. Tests Of Protective Coats For Carbon Steel

    NASA Technical Reports Server (NTRS)

    Macdowell, Louis G., III

    1995-01-01

    Report describes laboratory and field tests of candidate paints (primers, tie coats, and topcoats) for use in protecting carbon-steel structures against corrosion in seaside environment at Kennedy Space Center. Coating materials selected because of utility in preventing corrosion, also on basis of legal requirements, imposed in several urban areas, for reduction of volatile organic contents.

  8. Superhydrophobic conductive carbon nanotube coatings for steel.

    PubMed

    Sethi, Sunny; Dhinojwala, Ali

    2009-04-21

    We report the synthesis of superhydrophobic coatings for steel using carbon nanotube (CNT)-mesh structures. The CNT coating maintains its structural integrity and superhydrophobicity even after exposure to extreme thermal stresses and has excellent thermal and electrical properties. The coating can also be reinforced by optimally impregnating the CNT-mesh structure with cross-linked polymers without significantly compromising on superhydrophobicity and electrical conductivity. These superhydrophobic conductive coatings on steel, which is an important structural material, open up possibilities for many new applications in the areas of heat transfer, solar panels, transport of fluids, nonwetting and nonfouling surfaces, temperature resilient coatings, composites, water-walking robots, and naval applications.

  9. Ductile fracture of carbon steels: A review

    SciTech Connect

    Pospiech, J.

    1995-02-01

    This paper presents an extensive survey of literature on the theory of deformation and failure of inhomogeneous materials. Literature concerning deformation and fracture of carbon steels also is reviewed. The best utilization of deformability in cold-working processes translates into increased production, full use of available equipment capacity, and reduction of interannealing operations. In order to know the deformability of materials such as steels, one must know the mechanisms involved in deformation and fracture of nonhomogeneous materials, as well as the plastic fracture criterion. This requires use of metallographic examination techniques.

  10. Microbially induced corrosion of carbon steel in deep groundwater environment

    PubMed Central

    Rajala, Pauliina; Carpén, Leena; Vepsäläinen, Mikko; Raulio, Mari; Sohlberg, Elina; Bomberg, Malin

    2015-01-01

    The metallic low and intermediate level radioactive waste generally consists of carbon steel and stainless steels. The corrosion rate of carbon steel in deep groundwater is typically low, unless the water is very acidic or microbial activity in the environment is high. Therefore, the assessment of microbially induced corrosion of carbon steel in deep bedrock environment has become important for evaluating the safety of disposal of radioactive waste. Here we studied the corrosion inducing ability of indigenous microbial community from a deep bedrock aquifer. Carbon steel coupons were exposed to anoxic groundwater from repository site 100 m depth (Olkiluoto, Finland) for periods of 3 and 8 months. The experiments were conducted at both in situ temperature and room temperature to investigate the response of microbial population to elevated temperature. Our results demonstrate that microorganisms from the deep bedrock aquifer benefit from carbon steel introduced to the nutrient poor anoxic deep groundwater environment. In the groundwater incubated with carbon steel the planktonic microbial community was more diverse and 100-fold more abundant compared to the environment without carbon steel. The betaproteobacteria were the most dominant bacterial class in all samples where carbon steel was present, whereas in groundwater incubated without carbon steel the microbial community had clearly less diversity. Microorganisms induced pitting corrosion and were found to cluster inside the corrosion pits. Temperature had an effect on the species composition of microbial community and also affected the corrosion deposits layer formed on the surface of carbon steel. PMID:26257707

  11. Integrating Steel Production with Mineral Carbon Sequestration

    SciTech Connect

    Klaus Lackner; Paul Doby; Tuncel Yegulalp; Samuel Krevor; Christopher Graves

    2008-05-01

    The objectives of the project were (i) to develop a combination iron oxide production and carbon sequestration plant that will use serpentine ores as the source of iron and the extraction tailings as the storage element for CO2 disposal, (ii) the identification of locations within the US where this process may be implemented and (iii) to create a standardized process to characterize the serpentine deposits in terms of carbon disposal capacity and iron and steel production capacity. The first objective was not accomplished. The research failed to identify a technique to accelerate direct aqueous mineral carbonation, the limiting step in the integration of steel production and carbon sequestration. Objective (ii) was accomplished. It was found that the sequestration potential of the ultramafic resource surfaces in the US and Puerto Rico is approximately 4,647 Gt of CO2 or over 500 years of current US production of CO2. Lastly, a computer model was developed to investigate the impact of various system parameters (recoveries and efficiencies and capacities of different system components) and serpentinite quality as well as incorporation of CO2 from sources outside the steel industry.

  12. Ultrahigh carbon steel for automotive applications

    SciTech Connect

    Lesuer, D.R.; Syn, C.K.; Sherby, O.D.

    1995-12-04

    Ultrahigh carbon steels (UHCSs), which contain 1--2.1% carbon, have remarkable structural properties for automotive application when processed to achieve fine ferrite grains with fine spheroidized carbides. When processed for high room temperature ductility, UHCS can have good tensile ductility but significantly higher strength than current automotive high strength steels. The material can also be made superplastic at intermediate temperatures and exhibits excellent die fill capability. Furthermore, they can be made hard with high compression ductility. In wire form it is projected that UHCS can exhibit extremely high strengths (5,000 MPa) for tire cord applications. Examples of structural components that have been formed from fine-grained spheroidized UHCSs are illustrated.

  13. Lath martensites in low carbon steels

    SciTech Connect

    Sarikaya, M.; Thomas, G.

    1982-01-01

    The morphology and crystallography of lath martensite in low and medium carbon steels have been studied by transmission electron microscopy and diffraction. The steels have microduplex structures of dislocated lath martensite (a < b much less than c) with fairly straight boundaries and continuous interlath thin films of retained austenite. Stacks of laths (i.e., single crystals of martensite) form the packets which are derived from different (111) transformation variants of austenite. Microdiffraction experiments directly allow the determination of the orientation relationships between austenite and martensite. Relative orientations of adjacent individual laths cluster about common orientations from small to large angular differences all around a common <110>M direction. The overall microstructure and orientations result from minimization of the total strain and shape deformation. Considerable accommodation occurs by deformation of laths (sometimes twinned) and austenite (sometimes tripped to twin martensite). In the meantime, microchemical analyses have shown considerable carbon segregation to the martensite-austenite interface. 4 figures.

  14. Iron Cycling at Corroding Carbon Steel Surfaces

    DTIC Science & Technology

    2013-01-01

    bacteria (FeOB) and dissimilatory iron-reducing bacteria (FeRB) in seawater media under aerobic conditions were rougher than surfaces of CS exposed to pure...iron cycling (oxidation and reduction) on corroding CS in aerobic seawater media. Keywords: seawater; iron-oxidizing bacteria ; iron-reducing bacteria ...carbon steel; microbiologically influenced corrosion Introduction Iron oxidizing bacteria (FeOB) were among the first groups of microorganisms

  15. Comparative Structural Strength Research of Hardened Carbon Steel and Hot-Rolled Alloy Steel

    NASA Astrophysics Data System (ADS)

    Bogomolov, A. V.; Zhakupov, A. N.; Kanayev, A. T.; Sikach, I. A.; Tugumov, K. K.

    2016-08-01

    Experiments on quantitative evaluation of fatigue strength showed that St5ps and St5sp carbon steels with A400 strength class can be fully applied for erection of constructions and buildings having cyclical loads during operation. Study of corrosion resistance of hardened carbon steel in comparison with hot-rolled alloy steel consists in difference in structures and hence, difference in intensity of electric and chemical processes featuring presence of steel in concrete. Structure of St5sp steel with A400 strength class in surface area has significantly less corrosion rate than ferritic-perlitic structure of 35GS steel with A400 strength class.

  16. Preparation and characterization of 304 stainless steel/Q235 carbon steel composite material

    NASA Astrophysics Data System (ADS)

    Shen, Wenning; Feng, Lajun; Feng, Hui; Cao, Ying; Liu, Lei; Cao, Mo; Ge, Yanfeng

    The composite material of 304 stainless steel reinforced Q235 carbon steel has been prepared by modified hot-rolling process. The resulted material was characterized by scanning electron microscope, three-electrode method, fault current impact method, electrochemical potentiodynamic polarization curve measurement and electrochemical impedance spectroscopy. The results showed that metallurgical bond between the stainless steel layer and carbon steel substrate has been formed. The composite material exhibited good electrical conductivity and thermal stability. The average grounding resistance of the composite material was about 13/20 of dip galvanized steel. There has no surface crack and bubbling formed after fault current impact. The composite material led to a significant decrease in the corrosion current density in soil solution, compared with that of hot dip galvanized steel and bare carbon steel. On the basis polarization curve and EIS analyses, it can be concluded that the composite material showed improved anti-corrosion property than hot-dip galvanized steel.

  17. Friction stir processing on carbon steel

    SciTech Connect

    Tarasov, Sergei Yu.; Melnikov, Alexander G.; Rubtsov, Valery E.

    2014-11-14

    Friction stir processing of medium carbon steel samples has been carried out using a milling machine and tools made of cemented tungsten carbide. Samples have been machined from 40 and 40X steels. The tools have been made in the shape of 5×5×1.5 mm and 3×3×1.5 mm tetrahedrons. The microstructure of stirred zone has been obtained using the smaller tool and consists of fine recrystallized 2-3 μm grains, whereas the larger tool has produced the 'onion-like' structures comprising hard quenched 'white' 500-600 MPa layers with 300-350 MPa interlayers of bainite needles. The mean values of wear intensity obtained after measuring the wear scar width were 0.02 mm/m and 0.001 mm/m for non-processed and processed samples, respectively.

  18. Crack branching in carbon steel. Fracture mechanisms

    NASA Astrophysics Data System (ADS)

    Syromyatnikova, A. S.; Alekseev, A. A.; Levin, A. I.; Lyglaev, A. V.

    2010-04-01

    The fracture surfaces of pressure vessels made of carbon steel that form during crack branching propagation are examined by fractography. Crack branching is found to occur at a crack velocity higher than a certain critical value V > V c . In this case, the material volume that is involved in fracture and depends on the elastoplastic properties of the material and the sample width has no time to dissipate the energy released upon crack motion via the damage mechanisms intrinsic in the material under given deformation conditions (in our case, via cracking according to intragranular cleavage).

  19. Passivation of carbon steel through mercury implantation

    NASA Technical Reports Server (NTRS)

    Wilbur, P. J.; Robinson, R. S.

    1981-01-01

    An experiment, in which carbon steel samples were implanted with mercury ions from a broad beam ion source and their corrosion characteristics in air were evaluated, is described. Mercury doses of a few mA min/square cm at energies of a few hundred electron volts are shown to effect significant improvements in the corrosion resistance of the treated surfaces. In a warm moist environment the onset of rusting was extended from 15 min. for an untreated sample to approximately 30 hrs. for one implanted at a dose of 33 mA min/square cm with 1000 eV mercury ions.

  20. Spheroidization of medium-carbon steels

    SciTech Connect

    O`Brien, J.M.; Hosford, W.F.

    1997-02-01

    Spheroidization experiments were made on a medium-carbon AISI 4037 steel, using both intercritical and subcritical annealing cycles. The results indicate that in the subcritical cycle the spheroidization occurred much more quickly than expected, so that shorter times were sufficient to achieve high formability. On the other hand, the hardness dropped faster in the intercritical cycle. Although more work needs to be done, these results suggest that using a subcritical spheroidization process instead of an intercritical process could achieve considerable savings in time, energy, and cost.

  1. Stress Corrosion Cracking of Carbon Steel Weldments

    SciTech Connect

    POH-SANG, LAM

    2005-01-13

    An experiment was conducted to investigate the role of weld residual stress on stress corrosion cracking in welded carbon steel plates prototypic to those used for nuclear waste storage tanks. Carbon steel specimen plates were butt-joined with Gas Metal Arc Welding technique. Initial cracks (seed cracks) were machined across the weld and in the heat affected zone. These specimen plates were then submerged in a simulated high level radioactive waste chemistry environment. Stress corrosion cracking occurred in the as-welded plate but not in the stress-relieved duplicate. A detailed finite element analysis to simulate exactly the welding process was carried out, and the resulting temperature history was used to calculate the residual stress distribution in the plate for characterizing the observed stress corrosion cracking. It was shown that the cracking can be predicted for the through-thickness cracks perpendicular to the weld by comparing the experimental KISCC to the calculated stress intensity factors due to the welding residual stress. The predicted crack lengths agree reasonably well with the test data. The final crack lengths appear to be dependent on the details of welding and the sequence of machining the seed cracks, consistent with the prediction.

  2. Microstructure Analysis of Tungsten Carbide Hardfacing on Carbon Steel Blade

    NASA Astrophysics Data System (ADS)

    Nagentrau, M.; Tobi, A. L. Mohd; Kamdi, Z.; Ismail, M. I.; Sambu, M.

    2017-05-01

    Tungsten carbide (WC) hardfacing coating is commonly used to enhance carbon steel blade performance which works in acidic and abrasive condition during production process. This paper deals with tungsten carbide (WC) hardfacing microstructure analysis on a carbon steel blade. Mixing of ilmenite ore with sulphuric acid is performed by the carbon steel blade as part of a production process. Tungsten carbide hardfacing is deposited on the carbon steel blade to enhance its wear resistance. The carbide distribution along with elemental composition analysis of the hardfaced carbon steel blade specimens is examined using Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) and X-Ray Diffraction (XRD) respectively. Microstructure analysis revealed that different sizes of carbides with non-uniform distribution are found around the coating region. The carbide region is contains high percentage of tungsten (W) meanwhile, non-carbide region rich in tungsten (W) and iron (Fe).

  3. Qualification Data for the Corrosion Behavior of Inconel and Steel Alloys in Nitric Acid

    SciTech Connect

    Mickalonis, J.I.

    2001-04-17

    During filling operations in the Defense Waste Processing Facility (DWPF), melter inserts made of Inconel 690 (I690) have fallen into the canisters which are made of 304L stainless steel (304L). The consequences of possible galvanic corrosion between these materials were evaluated using two electrochemical techniques. Materials for other items which might fall into the canisters were also evaluated including Inconel MA758 (MA758) and A537 carbon steel (A537). The test solutions were concentrated nitric acid, used for validating literature data, and a 10 M nitric acid solution for simulating a possible environment, which may develop due to radiolysis inside the sealed canister.

  4. Qualification Data for the Corrosion Behavior of Inconel and Steel Alloys in Nitric Acid

    SciTech Connect

    Mickalonis, J.I.

    2001-05-02

    During filling operations in the Defense Waste Processing Facility (DWPF), melter inserts made of Inconel 690 (I690) have fallen into the canisters which are made of 304L stainless steel (304L). The consequences of possible galvanic corrosion between these materials were evaluated using two electrochemical techniques. Materials for other items which might fall into the canisters were also evaluated including Inconel MA758 (MA758) and A537 carbon steel (A537). The test solutions were concentrated nitric acid, used for validating literature data, and a 10 M nitric acid solution for simulating a possible environment, which may develop due to radiolysis inside the sealed canister.

  5. Carbon transfer from magnesia-graphite ladle refractories to ultra-low carbon steel

    NASA Astrophysics Data System (ADS)

    Russo, Andrew Arthur

    Ultra-low carbon steels are utilized in processes which require maximum ductility. Increases in interstitial carbon lower the ductility of steel; therefore, it is important to examine possible sources of carbon. The refractory ladle lining is one such source. Ladle refractories often contain graphite for its desirable thermal shock and slag corrosion resistance. This graphite is a possible source of carbon increase in ultra-low carbon steels. The goal of this research is to understand and evaluate the mechanisms by which carbon transfers to ultra-low carbon steel from magnesia-graphite ladle refractory. Laboratory dip tests were performed in a vacuum induction furnace under an argon atmosphere to investigate these mechanisms. Commercial ladle refractories with carbon contents between 4-12 wt% were used to investigate the effect of refractory carbon content. Slag-free dip tests and slag-containing dip tests with varying MgO concentrations were performed to investigate the influence of slag. Carbon transfer to the steel was controlled by steel penetrating into the refractory and dissolving carbon in dip tests where no slag was present. The rate limiting step for this mechanism is convective mass transport of carbon into the bulk steel. No detectable carbon transfer occurred in dip tests with 4 and 6 wt%C refractories without slag because no significant steel penetration occurred. Carbon transfer was controlled by the corrosion of refractory by slag in dip tests where slag was present.

  6. Solid-state joining of ultrahigh carbon steels

    SciTech Connect

    Sunwoo, A.J.

    1993-04-22

    A joining study of these steels was initiated to determine the feasibility of using ultrahigh carbon steels in structural applications. The high carbon content (1.5 wt%) in these steels and the desire to maintain the superplastic microstructure limit the use of conventional arc-welding processes. We chose two solid-state joining processes: diffusion bonding and inertia friction welding. Preliminary results show that sound bonds can be obtained with tensile properties nearly equal to those of the base metal. Of three UHC steels bonded by both inertia-friction welding and diffusion- bonding processes, the one with the lowest aluminum content had the best overall properties. Diffusion bonding with a nickel interlayer showed the most promising results for the UHC steel containing 1.6 wt% aluminum. The properties of inertia-friction-welded steels can be improved by a post-weld heat treatment.

  7. 75 FR 32911 - Preliminary Results of Antidumping Duty Administrative Review: Circular Welded Carbon Steel Pipes...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-10

    ... Welded Carbon Steel Pipes and Tubes From Taiwan AGENCY: Import Administration, International Trade... administrative review of the antidumping duty order on circular welded carbon steel pipes and tubes from Taiwan... circular welded carbon steel pipes and tubes from Taiwan. See Certain Circular Welded Carbon Steel...

  8. 76 FR 33210 - Preliminary Results of Antidumping Duty Administrative Review: Circular Welded Carbon Steel Pipes...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-08

    ... Welded Carbon Steel Pipes and Tubes From Taiwan AGENCY: Import Administration, International Trade... administrative review of the antidumping duty order on circular welded carbon steel pipes and tubes from Taiwan... circular welded carbon steel pipes and tubes from Taiwan. See Certain Circular Welded Carbon Steel...

  9. Corrosion tests of carbon steel exposed to a simulated DWPF recycle stream

    SciTech Connect

    Zapp, P.E.

    1993-09-30

    Coupon immersion tests of ASTM A537 Class 1 carbon steel in simulated DWPF recycle solutions did not generate shock-sensitive deposits, consistent with two previous tests at SRTC. Results of three sets of tests indicate that the formation of detectable amounts of shock-sensitive deposits is not possible under test conditions. Solutions used included the increased nitrate concentration (0.05 M vs.the 0.01 M used previously) that reflects the introduction of ammonia scrubbing in the DWPF. The nitrite and hydroxide concentrations were 0.042 M and 0.5 M, respectively, which are the current Process Requirement concentrations for the DWPF Recycle Collection Tank. As a result of the increased nitrate level, the coupon showed superficial uniform corrosion at a rate {le} 0.4 mils per year (0.0004 in. per year) and pitting corrosion with a maximum depth of 0.7 mils (0.0007 in.). Electrochemical corrosion tests to revise the nitrite concentration limit to accommodate the higher nitrate concentration will be completed in October, 1993.

  10. Tests Of Materials For Repair Coating Of Carbon Steel

    NASA Technical Reports Server (NTRS)

    Macdowell, Louis G., III

    1995-01-01

    Report describes tests of paints (primers and topcoats) for use in recoating rusted carbon steel for protection against further corrosion. Paints selected for evaluation all designated by manufacturers as suitable for application over tightly adhering rust.

  11. 6. INTERIOR VIEW, HIGH CARBON HOT ROLLED SHEET STEEL FOR ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    6. INTERIOR VIEW, HIGH CARBON HOT ROLLED SHEET STEEL FOR NAIL PLATE BEING LOADED ON THE CRADLE USED DURING THE PICKLING PROCESS - LaBelle Iron Works, Thirtieth & Wood Streets, Wheeling, Ohio County, WV

  12. 5. INTERIOR VIEW, HIGH CARBON HOT ROLLED SHEET STEEL FOR ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    5. INTERIOR VIEW, HIGH CARBON HOT ROLLED SHEET STEEL FOR NAIL PLATE BEING REMOVED FROM THE CRADLE USED DURING THE PICKLING PROCESS - LaBelle Iron Works, Thirtieth & Wood Streets, Wheeling, Ohio County, WV

  13. Low carbon dual phase steels for high strength wire

    SciTech Connect

    Thomas, G.; Ahn, J.H.

    1985-08-01

    This paper shows that dual phase steels can be designed and processed as new, economical low carbon steels for cold drawing into high tensile strength steel wires. Current work indicates wires of tensile strengths up to 400,000 psi can be obtained. Potential applications for dual phase steel wire include bead wire, tire cord, wire rope and prestressed concrete. It should be possible to produce wire rods in existing rod mills by adapting the controlled rolling and quenching procedures outlined in this paper.

  14. Iron cycling at corroding carbon steel surfaces

    PubMed Central

    Lee, Jason S.; McBeth, Joyce M.; Ray, Richard I.; Little, Brenda J.; Emerson, David

    2013-01-01

    Surfaces of carbon steel (CS) exposed to mixed cultures of iron-oxidizing bacteria (FeOB) and dissimilatory iron-reducing bacteria (FeRB) in seawater media under aerobic conditions were rougher than surfaces of CS exposed to pure cultures of either type of microorganism. The roughened surface, demonstrated by profilometry, is an indication of loss of metal from the surface. In the presence of CS, aerobically grown FeOB produced tight, twisted helical stalks encrusted with iron oxides. When CS was exposed anaerobically in the presence of FeRB, some surface oxides were removed. However, when the same FeOB and FeRB were grown together in an aerobic medium, FeOB stalks were less encrusted with iron oxides and appeared less tightly coiled. These observations suggest that iron oxides on the stalks were reduced and solubilized by the FeRB. Roughened surfaces of CS and denuded stalks were replicated with three culture combinations of different species of FeOB and FeRB under three experimental conditions. Measurements of electrochemical polarization resistance established different rates of corrosion of CS in aerobic and anaerobic media, but could not differentiate rate differences between sterile controls and inoculated exposures for a given bulk concentration of dissolved oxygen. Similarly, total iron in the electrolyte could not be used to differentiate treatments. The experiments demonstrate the potential for iron cycling (oxidation and reduction) on corroding CS in aerobic seawater media. PMID:24093730

  15. Iron cycling at corroding carbon steel surfaces.

    PubMed

    Lee, Jason S; McBeth, Joyce M; Ray, Richard I; Little, Brenda J; Emerson, David

    2013-01-01

    Surfaces of carbon steel (CS) exposed to mixed cultures of iron-oxidizing bacteria (FeOB) and dissimilatory iron-reducing bacteria (FeRB) in seawater media under aerobic conditions were rougher than surfaces of CS exposed to pure cultures of either type of microorganism. The roughened surface, demonstrated by profilometry, is an indication of loss of metal from the surface. In the presence of CS, aerobically grown FeOB produced tight, twisted helical stalks encrusted with iron oxides. When CS was exposed anaerobically in the presence of FeRB, some surface oxides were removed. However, when the same FeOB and FeRB were grown together in an aerobic medium, FeOB stalks were less encrusted with iron oxides and appeared less tightly coiled. These observations suggest that iron oxides on the stalks were reduced and solubilized by the FeRB. Roughened surfaces of CS and denuded stalks were replicated with culture combinations of different species of FeOB and FeRB under three experimental conditions. Measurements of electrochemical polarization resistance established different rates of corrosion of CS in aerobic and anaerobic media, but could not differentiate rate differences between sterile controls and inoculated exposures for a given bulk concentration of dissolved oxygen. Similarly, total iron in the electrolyte could not be used to differentiate treatments. The experiments demonstrate the potential for iron cycling (oxidation and reduction) on corroding CS in aerobic seawater media.

  16. 75 FR 26273 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-11

    ... COMMISSION Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From China AGENCY...-fair-value imports from China of certain seamless carbon and alloy steel standard, line, and pressure... merchandise as ``* * * Certain seamless carbon and alloy steel (other than stainless steel) pipes and...

  17. Microstructural, Structural, and Thermal Characterization of Annealed Carbon Steels

    NASA Astrophysics Data System (ADS)

    Lara-Guevara, A.; Ortiz-Echeverri, C. J.; Rojas-Rodriguez, I.; Mosquera-Mosquera, J. C.; Ariza-Calderón, H.; Ayala-Garcia, I.; Rodriguez-García, M. E.

    2016-10-01

    As is well known, the metallurgical microstructure of carbon steel is formed by ferrite and pearlite after the annealing heat treatment. When the cooling rate increases, the diffusive process is interrupted causing a change in the metallurgical microstructure which will affect steel properties. The aim of this work was to study thermal, structural, and microstructural properties of annealed carbon steel samples with four different carbon contents. Crystalline structure and crystalline quality were studied by the X-ray diffraction technique, where the full width at half maximum analysis showed that as the carbon content increased, the crystalline quality decreased. The metallurgical microstructure morphology was studied by scanning electron microscopy. The thermal diffusivity and the heat capacity were determined by the photoacoustic technique and by the thermal relaxation method, respectively. The thermal diffusivity and the thermal conductivity decreased as the carbon content increased. The amplitude signal of photothermal radiometry increased as the carbon content increased, while the phase signal of photothermal radiometry did not show significant differences among studied carbon steel types. The photoacoustic technique represents an important alternative in the steel characterization field.

  18. Super-Hydrophobic Green Corrosion Inhibitor On Carbon Steel

    NASA Astrophysics Data System (ADS)

    Hassan, H.; Ismail, A.; Ahmad, S.; Soon, C. F.

    2017-06-01

    There are many examples of organic coatings used for corrosion protection. In particular, hydrophobic and super-hydrophobic coatings are shown to give good protection because of their enhanced ability to slow down transport of water and ions through the coating. The purpose of this research is to develop water repellent coating to avoid direct contact between metal and environment corrosive and mitigate corrosion attack at pipeline system. This water repellent characteristic on super-hydrophobic coating was coated by electrodeposition method. Wettability of carbon steel with super-hydrophobic coating (cerium chloride and myristic acid) and oxidized surface was investigated through contact angle and inhibitor performance test. The inhibitor performance was studied in 25% tannin acid corrosion test at 30°C and 3.5% sodium chloride (NaCl). The water contact angle test was determined by placing a 4-μL water droplet of distilled water. It shows that the wettability of contact angle super-hydrophobic with an angle of 151.60° at zero minute can be classified as super-hydrophobic characteristic. By added tannin acid as inhibitor the corrosion protection on carbon steel becomes more consistent. This reveals that the ability of the coating to withstand with the corrosion attack in the seawater at different period of immersions. The results elucidate that the weight loss increased as the time of exposure increased. However, the corrosion rates for uncoated carbon steel is high compared to coated carbon steel. As a conclusion, from both samples it can be seen that the coated carbon steel has less corrosion rated compared to uncoated carbon steel and addition of inhibitor to the seawater provides more protection to resist corrosion attack on carbon steel.

  19. Comparison of carbon fiber and stainless steel root canal posts.

    PubMed

    Purton, D G; Payne, J A

    1996-02-01

    This in vitro study compared physical properties of root canal posts made of carbon fiber-reinforced epoxy resin with those of stainless steel posts. Three-point bending tests were used to derive the transverse modulus of elasticity of the posts. Resin composite cores on the posts were subjected to tensile forces to test the bonds between the cores and posts. Carbon fiber posts appeared to have adequate rigidity for their designed purpose. The bond strength of the resin composite cores to the carbon fiber posts was significantly less than that to the stainless steel posts.

  20. Structure and properties of a steel/white-cast-iron bimetal produced by method of carbonizing the steel melt

    NASA Astrophysics Data System (ADS)

    Sapozhnikov, S. Z.

    1985-11-01

    Centrifugal bimetallization by the method of carbonizing the steel melt makes it possible to obtain a steel/white-cast-iron composition with a cladding layer close to the eutectic in terms of composition.

  1. 48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and...

  2. 48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and...

  3. 48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and...

  4. 48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and...

  5. 48 CFR 252.225-7030 - Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... of Carbon, Alloy, and Armor Steel Plate. 252.225-7030 Section 252.225-7030 Federal Acquisition... Acquisition of Carbon, Alloy, and Armor Steel Plate. As prescribed in 225.7011-3, use the following clause: Restriction on Acquisition of Carbon, Alloy, and Armor Steel Plate (DEC 2006) (a) Carbon, alloy, and...

  6. Correlation Between Shear Punch and Tensile Strength for Low-Carbon Steel and Stainless Steel Sheets

    NASA Astrophysics Data System (ADS)

    Mahmudi, R.; Sadeghi, M.

    2013-02-01

    The deformation behavior of AISI 1015 low-carbon steel, and AISI 304 stainless steel sheets was investigated by uniaxial tension and the shear punch test (SPT). Both materials were cold rolled to an 80% thickness reduction and subsequently annealed in the temperature range 25-850 °C to produce a wide range of yield and ultimate strength levels. The correlations between shear punch and tensile yield and ultimate stresses were established empirically. Different linear relationships having different slopes and intercepts were found for the low-carbon and stainless steel sheets, and the possible parameters affecting the correlation were discussed. It was shown that, within limits, yield and tensile strength of thin steel sheets can be predicted from the shear data obtained by the easy-to-perform SPT.

  7. ASM Specialty Handbook{reg_sign}: Carbon and alloy steels

    SciTech Connect

    Davis, J.R.

    1995-12-31

    Carbon and alloy steels are the workhorse of structural materials in modern engineering because of their very reasonable costs coupled with their many and varied properties that allow their use in such a large array of applications. it`s very easy to take steel for granted and forget how much it`s relied upon in critical uses such as cars, bridges, buildings, landing gear assemblies, and more. There are in-depth reviews on formability weldability, machineability, and hardenability of the various steel grades. One can also discover how adding certain alloys can significantly improve steel processing. The strength and toughness section has been greatly expanded with more coverage than ever before of corrosion fatigue. One has access to extensive reports detailing which steels are more susceptible to environmental damage such as stress-corrosion and hydrogen embrittlement. Temperature effects relating to mechanical properties and corrosion are also discussed.

  8. Laser ignition of bulk 1018 carbon steel in pure oxygen

    NASA Technical Reports Server (NTRS)

    Nguyen, K.; Branch, M. C.

    1986-01-01

    Experiments were undertaken to study the ignition characteristics of bulk 1018 carbon steel in a pure oxygen environment. Cylindrical 1018 carbon steel specimens 5 mm in diameter and 5 mm high were ignited by a focused CW CO2 laser beam in a cool, static, pure oxygen environment at oxygen pressures ranging from 0.103 to 6.895 MPa. A two-color pyrometer was designed and used to measure the ignition temperatures of the specimens. The temperature history of a spot approximately 0.5 mm in diameter located at the center of the specimen top surface was recorded with a maximum time resolution of 25 microsec, and with an accuracy of a few percent. Ignition temperature of bulk 1018 carbon steel was identified from the temperature history curve with the aid of the light intensity curve. Results show that 1018 carbon steel specimens ignite at temperatures between 1388 and 1450 K, which are below the melting range of the alloy (1662-1685 K). The ignition temperature of 1018 carbon steel is mildly dependent on oxygen pressure over the range of oxygen pressure investigated in this study.

  9. Diffusivity of carbon in iron and steels at high temperatures

    NASA Astrophysics Data System (ADS)

    Tibbetts, Gary G.

    1980-09-01

    Although the literature contains many measurements of the diffusivity of carbon in Fe and steels, recent progress in plasma carburizing has made this regime around 1050 °C and over 1% carbon concentration of great interest. We have measured the diffusivity of carbon in steel from 975 to 1075 °C up to 1.3% carbon concentration by the steady-state method. Our results are in agreement with previous measurements of Smith and Wells, Batz, and Mehl in the regime of low temperatures and carbon concentrations. Using activation energies determined over a wider temperature range by the latter authors, we derive as an empirical expression for D throughout the range of temperatures and concentrations investigated, D=0.47 exp (-1.6 C) ×exp[-(37 000-6600 C)/RT] cm2/sec. Here, C is expressed in weight percent carbon and the energies are in cal/mole.

  10. Corrosion of carbon steels, stainless steels, and titanium in aqueous lithium bromide solution

    SciTech Connect

    Guinon, J.L.; Garcia-Anton, J.; Perez-Herranz, V. . Dept. de Ingenieria Quimica y Nuclear); Lacoste, G. )

    1994-03-01

    Effects of lithium bromide (LiBr) concentration, pH, temperature, exposure time, and the action of some inhibitors on corrosion of several carbon (C) steels, stainless steels (SS), and a titanium (Ti) alloy were studied. Corrosion rates were determined by the polarization resistance method and compared to rates determined by weight-loss measurements. Pitting potentials (E[sub p]) were evaluated in neutral LiBr solution and with different inhibitors. Pit density and average pit depth depended on the metal tested, with lowest values for Ti, the next lowest values for type 316 SS (UNS S31600), and the highest values for UNS G41350 tempered steel.

  11. Increasing corrosion resistance of carbon steels by surface laser cladding

    NASA Astrophysics Data System (ADS)

    Polsky, V. I.; Yakushin, V. L.; Dzhumaev, P. S.; Petrovsky, V. N.; Safonov, D. V.

    2016-04-01

    This paper presents results of investigation of the microstructure, elemental composition and corrosion resistance of the samples of low-alloy steel widely used in the engineering, after the application of laser cladding. The level of corrosion damage and the corrosion mechanism of cladded steel samples were established. The corrosion rate and installed discharge observed at the total destruction of cladding were obtained. The regularities of structure formation in the application of different powder compositions were obtained. The optimal powder composition that prevents corrosion of samples of low-carbon low-alloy steel was established.

  12. Thermal embrittlement of carbon steels in canistered waste disposal containers

    SciTech Connect

    Huang, J.S.

    1998-03-01

    It is known that fracture toughness in steels, especially in low steels, in severely reduced by exposure at the temperature range of 350-575{degrees}C through isothermal aging or slow cooling. It is also well recognized that segregation of impurities, such as Sb, P, Sn, As, along prior austenite grain boundaries is the main cause of thermal (temper) embrittlement. The most potent embrittling elements, in order of decreasing potency, are Sb, Sn, P, and As. However, Sb, Sn, and As are not generally present in steels. Therefore P is usually the most concerned element in steels. McMahon has concluded in his review that plain C steels containing less than 0.5 wt% Mn are not susceptible to temper embrittlement. However, he also noted the strong effect of Mn as an enhancement of the P aging of plain C-Mn steels, particularly high Mn contents, to disregard the possibility of thermal embrittlement. A516 plain carbon steels has been been proposed as a corrosion allowable material (CRM) for the outer barrier of canistered waste disposal containers. The expected peak temperature for a waste package container if as high as 200{degrees}C for many years. Therefore concern has been raised whether thermal embrittlement would occur in this steel after the long term temperature exposure expected in the current nuclear waste packages. The current report documents our recent analysis for this problem.

  13. Initial Atmospheric Corrosion of Carbon Steel in Industrial Environment

    NASA Astrophysics Data System (ADS)

    Han, Wei; Pan, Chen; Wang, Zhenyao; Yu, Guocai

    2015-02-01

    The initial corrosion behavior of carbon steel subjected to Shenyang industrial atmosphere has been investigated by weight-loss measurement, scanning electron microscopy observation, x-ray diffraction, auger electron spectroscopy, and electron probe microanalysis. The experimental results reveal that the corrosion kinetics of the initial corrosion of carbon steel in industrial atmosphere follows empirical equation D = At n , and there is a corrosion rate transition from corrosion acceleration to deceleration; the corrosion products are composed of γ-FeOOH, α-FeOOH, Fe3O4, as well as FeS which is related to the existence of sulfate-reducing bacteria in the rust layers. The effect of dust particles on the corrosion evolution of carbon steel has also been discussed.

  14. 77 FR 65712 - Circular Welded Carbon-Quality Steel Pipe From Vietnam; Termination of Investigation

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-30

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Circular Welded Carbon-Quality Steel Pipe From Vietnam; Termination of Investigation AGENCY... investigation concerning circular welded carbon-quality steel pipe from Vietnam (investigation No....

  15. Residual stress measurements in carbon steel

    NASA Technical Reports Server (NTRS)

    Heyman, J. S.; Min, N.

    1986-01-01

    External dc magnetic field-induced changes in natural velocity of Rayleigh surface waves were measured in steel specimens under various stress conditions. The low field slopes of curves representing the fractional changes of natural velocity were proved to provide correct stress information in steels with different metallurgical properties. The slopes of curves under uniaxial compression, exceeding about one third of the yield stress, fell below zero in all the specimens when magnetized along the stress axis. The slopes under tension varied among different steels but remained positive in any circumstances. The stress effect was observed for both applied and residual stress. A physical interpretation of these results is given based on the stress-induced domain structure changes and the delta epsilon effect. Most importantly, it is found that the influence of detailed metallurgical properties cause only secondary effects on the obtained stress information.

  16. 75 FR 44766 - Certain Welded Carbon Steel Standard Pipe from Turkey: Final Results of Countervailing Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-29

    ... International Trade Administration Certain Welded Carbon Steel Standard Pipe from Turkey: Final Results of...) order on certain welded carbon steel standard pipe from Turkey for the January 1, 2008, through December 31, 2008, period of review (POR). See Certain Welded Carbon Steel Standard Pipe From...

  17. 78 FR 15376 - Determinations: Corrosion-Resistant Carbon Steel Flat Products From Germany and Korea

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-11

    ... COMMISSION Determinations: Corrosion-Resistant Carbon Steel Flat Products From Germany and Korea On the basis...)), that revocation of the countervailing duty order on corrosion-resistant carbon steel flat products from Korea and the antidumping duty orders on corrosion-resistant carbon steel flat products from Germany...

  18. 78 FR 70069 - Circular Welded Carbon-Quality Steel Pipe From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-11-22

    ... COMMISSION Circular Welded Carbon-Quality Steel Pipe From China Determination On the basis of the record \\1... antidumping and countervailing duty orders on circular welded carbon-quality steel pipe from China would be... Publication 4435 (November 2013), entitled Circular Welded Carbon-Quality Steel Pipe from China:...

  19. 77 FR 20782 - Circular Welded Carbon Steel Pipes and Tubes From Thailand: Preliminary Results of Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-06

    ... International Trade Administration Circular Welded Carbon Steel Pipes and Tubes From Thailand: Preliminary... administrative review of the antidumping duty order on circular welded carbon steel pipes and tubes from Thailand... circular welded carbon steel pipes and tubes have been made below normal value (NV) during the March...

  20. 78 FR 21107 - Circular Welded Carbon Steel Pipes and Tubes from Turkey: Preliminary Results of Countervailing...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-09

    ... International Trade Administration Circular Welded Carbon Steel Pipes and Tubes from Turkey: Preliminary Results... carbon steel pipes and tubes from Turkey (pipes and tubes from Turkey) for the period of review (POR) of... welded carbon steel pipe and tube with an outside diameter of 0.375 inch or more, but not over 16...

  1. 77 FR 64468 - Circular Welded Carbon-Quality Steel Pipe From India: Final Affirmative Countervailing Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-22

    ... International Trade Administration Circular Welded Carbon-Quality Steel Pipe From India: Final Affirmative... countervailable subsidies are being provided to producers and exporters of circular welded carbon-quality steel... the publication of the preliminary determination.\\1\\ \\1\\ See Circular Welded Carbon-Quality Steel...

  2. 76 FR 15299 - Certain Hot-Rolled Carbon Steel Flat Products From India: Preliminary Rescission of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-21

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From India: Preliminary... countervailing duty (CVD) order on certain hot-rolled carbon steel flat products from India. See Antidumping or... The products covered under this order are certain hot-rolled flat- rolled carbon steel flat products...

  3. 77 FR 59892 - Carbon and Certain Alloy Steel Wire Rod From Mexico: Affirmative Final Determination of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-01

    ... International Trade Administration Carbon and Certain Alloy Steel Wire Rod From Mexico: Affirmative Final... mm to 5.0 mm. \\1\\ See Carbon and Certain Alloy Steel Wire Rod from Mexico: Affirmative Preliminary... on said entries.\\4\\ \\2\\ See Carbon and Certain Alloy Steel Wire Rod from Mexico: Initiation of...

  4. 77 FR 19711 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From Germany...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-02

    ... COMMISSION Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From Germany... revocation of the antidumping duty order on certain seamless carbon and alloy steel standard, line, and... Commission found one Domestic Like Product consisting of seamless carbon and alloy steel standard,...

  5. 77 FR 19192 - Circular Welded Carbon-Quality Steel Pipe From India: Preliminary Affirmative Countervailing Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-30

    ... International Trade Administration Circular Welded Carbon-Quality Steel Pipe From India: Preliminary Affirmative... being provided to producers and exporters of circular welded carbon-quality steel pipe (``circular... Carbon-Quality Steel Pipe from India, the Sultanate of Oman, the United Arab Emirates, and the...

  6. Corrosion behavior of carbon steels under tuff repository environmental conditions

    SciTech Connect

    McCright, R.D.; Weiss, H.

    1984-10-01

    Carbon steels may be used for borehole liners in a potential high-level nuclear waste repository in tuff in Nevada. Borehole liners are needed to facilitate emplacement of the waste packages and to facilitate retrieval of the packages, if required. Corrosion rates of low carbon structural steels AISI 1020 and ASTM A-36 were determined in J-13 well water and in saturated steam at 100{sup 0}C. Tests were conducted in air-sparged J-13 water to attain more oxidizing conditions representative of irradiated aqueous environments. A limited number of irradiation corrosion and stress corrosion tests were performed. Chromium-molybdenum alloy steels and cast irons were also tested. These materials showed lower general corrosion but were susceptible to stress corrosion cracking when welded. 4 references, 4 tables.

  7. INHIBITION OF STRESS CORROSION CRACKING OF CARBON STEEL STORAGE TANKS AT HANFORD

    SciTech Connect

    BOOMER, K.D.

    2007-01-31

    The stress corrosion cracking (SCC) behavior of A537 tank steel was investigated in a series of environments designed to simulate the chemistry of legacy nuclear weapons production waste. Tests consisted of both slow strain rate tests using tensile specimens and constant load tests using compact tension specimens. Based on the tests conducted, nitrite was found to be a strong SCC inhibitor. Based on the test performed and the tank waste chemistry changes that are predicted to occur over time, the risk for SCC appears to be decreasing since the concentration of nitrate will decrease and nitrite will increase.

  8. Upset Resistance Welding of Carbon Steel to Austenitic Stainless Steel Narrow Rods

    NASA Astrophysics Data System (ADS)

    Ozlati, Ashkaan; Movahedi, Mojtaba; Mohammadkamal, Helia

    2016-11-01

    Effects of welding current (at the range of 2-4 kA) on the microstructure and mechanical properties of upset resistance welds of AISI-1035 carbon steel to AISI-304L austenitic stainless steel rods were investigated. The results showed that the joint strength first increased by raising the welding current up to 3 kA and then decreased beyond it. Increasing trend was related to more plastic deformation, accelerated diffusion, reduction of defects and formation of mechanical locks at the joint interface. For currents more than 3 kA, decrease in the joint strength was mainly caused by formation of hot spots. Using the optimum welding current of 3 kA, tensile strength of the joint reached to 76% of the carbon steel base metal strength. Microstructural observations and microhardness results confirmed that there was no hard phase, i.e., martensite or bainite, at the weld zone. Moreover, a fully austenitic transition layer related to carbon diffusion from carbon steel was observed at the weld interface.

  9. Carbon distribution in bainitic steel subjected to deformation

    SciTech Connect

    Ivanov, Yu. F.; Nikitina, E. N. Gromov, V. E.

    2015-10-27

    Analysis of the formation and evolution of carbide phase in medium carbon steel with a bainitic structure during compressive deformation was performed by means of transmission electron diffraction microscopy. Qualitative transformations in carbide phase medium size particles, their density and volume concentration depended on the degree of deformation.

  10. Investigate the magnetic behaviour of thermal treated carbon steel

    NASA Astrophysics Data System (ADS)

    Kanelopoulos, N. P.

    2016-03-01

    The present paper investigates the utilization of the magnetic hysteresis loops and Barkhausen Noise for the non-destructive characterization of annealed and quenched carbon steels samples. The resulting magnetic properties were further evaluated by examining the microstructure of the samples by using scanning electron microscopy.

  11. Nondestructive evaluation of residual stress in low-carbon steel

    NASA Technical Reports Server (NTRS)

    Salama, K.

    1984-01-01

    The effects of the preferred orientation on the temperature dependence of ultrasonic velocity in low carbon steels are investigated. The sensitivity of the acousto-elastic constant to changes in microstructure is assessed as well as the possibility of determining some mechanical properties of a material by measuring the acousto-elastic constant.

  12. Microstructure/property relationships in dissimilar welds between duplex stainless steels and carbon steels

    SciTech Connect

    Barnhouse, E.J.; Lippold, J.C.

    1998-12-01

    The metallurgical characteristics, toughness and corrosion resistance of dissimilar welds between duplex stainless steel Alloy 2205 and carbon steel A36 have been evaluated. Both duplex stainless steel ER2209 and Ni-based Alloy 625 filler metals were used to join this combination using a multipass, gas tungsten arc welding (GTAW) process. Defect-free welds were made with each filler metal. The toughness of both the 625 and 2209 deposits were acceptable, regardless of heat input. A narrow martensitic region with high hardness was observed along the A36/2209 fusion boundary. A similar region was not observed in welds made with the 625 filler metal. The corrosion resistance of the welds made with 2209 filler metal improved with increasing heat input, probably due to higher levels of austenite and reduced chromium nitride precipitation. Welds made with 625 exhibited severe attack in the root pass, while the bulk of the weld was resistant. This investigation has shown that both filler metals can be used to joint carbon steel to duplex stainless steels, but that special precautions may be necessary in corrosive environments.

  13. Morphological and microstructural studies on aluminizing coating of carbon steel

    SciTech Connect

    Samsu, Zaifol; Othman, Norinsan Kamil; Daud, Abd Razak; Hussein, Hishammuddin

    2013-11-27

    Hot dip aluminizing is one of the most effective methods of surface protection for steels and is gradually gaining popularity. The morphology and microstructure of an inter-metallic layer form on the surface of low carbon steel by hot dip aluminization treatment had been studied in detail. This effect has been investigated using optical and scanning electron microscopy, and X-ray diffraction. The result shows that the reaction between the steel and the molten aluminium leads to the formation of Fe–Al inter-metallic compounds on the steel surface. X-ray diffraction and electron microscopic studies showed that a two layer coating was formed consisting of an external Al layer and a (Fe{sub 2}Al{sub 5}) inter metallic on top of the substrate after hot dip aluminizing process. The inter-metallic layer is ‘thick’ and exhibits a finger-like growth into the steel. Microhardness testing shown that the intermetallic layer has high hardness followed by steel substrate and the lowest hardness was Al layer.

  14. Laser beam hardening of cast carbon steels, plain cast irons, and high-speed steels

    NASA Astrophysics Data System (ADS)

    Bylica, Andrzej; Adamiak, Stanislaw; Bochnowski, Wojciech; Dziedzic, Andrzej

    2000-11-01

    The examinations of the structure, hardness and abrasion resistance of surface layer of Fe-C alloys having the contents of carbon up to 4% and high-speed steel: 6-5-2, 4- 4-2-5+C after laser hardening are presented in the paper. They are compared with the properties obtained after conventional hardening. Laser of impulse operation - YAG:Nd and of continuous operation - CO2 were used. Analysis of structure was carried out based on metallographic and fractographic examinations as well as on X-ray properties, parameters of laser and conventional heat treatment of steels were defined.

  15. Gas phase hydrogen permeation in alpha titanium and carbon steels

    NASA Technical Reports Server (NTRS)

    Johnson, D. L.; Shah, K. K.; Reeves, B. H.; Gadgeel, V. L.

    1980-01-01

    Commercially pure titanium and heats of Armco ingot iron and steels containing from 0.008-1.23 w/oC were annealed or normalized and machined into hollow cylinders. Coefficients of diffusion for alpha-Ti and alpha-Fe were determined by the lag-time technique. Steady state permeation experiments yield first power pressure dependence for alpha-Ti and Sievert's law square root dependence for Armco iron and carbon steels. As in the case of diffusion, permeation data confirm that alpha-titanium is subject to at least partial phase boundary reaction control while the steels are purely diffusion controlled. The permeation rate in steels also decreases as the carbon content increases. As a consequence of Sievert's law, the computed hydrogen solubility decreases as the carbon content increases. This decreases in explained in terms of hydrogen trapping at carbide interfaces. Oxidizing and nitriding the surfaces of alpha-titanium membranes result in a decrease in the permeation rate for such treatment on the gas inlet surfaces but resulted in a slight increase in the rate for such treatment on the gas outlet surfaces. This is explained in terms of a discontinuous TiH2 layer.

  16. Anticorrosive Influence of Acetobacter aceti Biofilms on Carbon Steel

    NASA Astrophysics Data System (ADS)

    France, Danielle Cook

    2016-09-01

    Microbiologically influenced corrosion (MIC) of carbon steel infrastructure is an emerging environmental and cost issue for the ethanol fuel industry, yet its examination lacks rigorous quantification of microbiological parameters that could reveal effective intervention strategies. To quantitatively characterize the effect of cell concentration on MIC of carbon steel, numbers of bacteria exposed to test coupons were systematically controlled to span four orders of magnitude throughout a seven-day test. The bacterium studied, Acetobacter aceti, has been found in ethanol fuel environments and can convert ethanol to the corrosive species acetic acid. A. aceti biofilms formed during the test were qualitatively evaluated with fluorescence microscopy, and steel surfaces were characterized by scanning electron microscopy. During exposure, biofilms developed more quickly, and test reactor pH decreased at a faster rate, when cell exposure was higher. Resulting corrosion rates, however, were inversely proportional to cell exposure, indicating that A. aceti biofilms are able to protect carbon steel surfaces from corrosion. This is a novel demonstration of corrosion inhibition by an acid-producing bacterium that occurs naturally in corrosive environments. Mitigation techniques for MIC that harness the power of microbial communities have the potential to be scalable, inexpensive, and green solutions to industrial problems.

  17. Thermophysical property measurements on low alloy high strength carbon steels

    SciTech Connect

    Li, M.; Brooks, J.A.; Atteridge, D.G.; Porter, W.D.

    1997-06-15

    The alloys of interest in this study were AISI Type 4230 and Type 4320 low alloy high strength carbon steels. They are heat-treatable steels and are usually used in the quenched and tempered condition. The Type 4130 has about 0.3% (wt.)C, 0.95%Cr, and 0.2% Mo. The Type 4320 has about 0.2%C, 1.7%Ni, 0.7%Cr, and 0.3% Mo. They are among the most popular alloy steels because of their excellent combination of mechanical properties and are used in both cast and wrought forms for many applications requiring high strength and toughness. However, during the casting operation, carbon segregation to the part surface forms a high carbon content surface layer in the part, which will induce surface cracking in the subsequent quenching process. And, during the welding operation, the critical cooling rate in the heat-affected zone (HAZ) will determine if the weldment is crack-free or not. Thus, the numerical effort to study the thermal history, microstructure evolution and residual stress development during welding and casting is critical to the application of these steels. This modeling effect requires the accurate knowledge of thermophysical properties, such as thermal expansion, solidus and liquidus temperatures, specific heat capacity, and heat of fusion. Unfortunately, these thermophysical properties are unavailable for temperatures over 1,000 C (1,2), thus the need for this study.

  18. Novel sintered ceramic materials incorporated with EAF carbon steel slag

    NASA Astrophysics Data System (ADS)

    Karayannis, V.; Ntampegliotis, K.; Lamprakopoulos, S.; Papapolymerou, G.; Spiliotis, X.

    2017-01-01

    In the present research, novel sintered clay-based ceramic materials containing electric arc furnace carbon steel slag (EAFC) as a useful admixture were developed and characterized. The environmentally safe management of steel industry waste by-products and their valorization as secondary resources into value-added materials towards circular economy have attracted much attention in the last years. EAF Carbon steel slag in particular, is generated during the manufacture of carbon steel. It is a solid residue mainly composed of rich-in- Fe, Ca and Si compounds. The experimental results show that the beneficial incorporation of lower percentages of EAFC up to 6%wt. into ceramics sintered at 950 °C is attained without significant variations in sintering behavior and physico-mechanical properties. Further heating up to 1100 °C strongly enhances the densification of the ceramic microstructures, thus reducing the porosity and strengthening their mechanical performance. On the other side, in terms of thermal insulation behavior as well as energy consumption savings and production cost alleviation, the optimum sintering temperature appears to be 950 °C.

  19. MECHANISTIC UNDERSTANDING OF CAUSTIC CRACKING OF CARBON STEELS

    SciTech Connect

    Garcia-Diaz, B.; Roy, A.

    2009-10-19

    Liquid waste generated by the PUREX process for separation of nuclear materials is concentrated and stored in Type IV single-shell carbon steel tanks at the Savannah River Site (SRS). The Type IV tanks for this waste do not have cooling coils and have not undergone heat treatment to stress-relieve the tanks. After the waste is concentrated by evaporation, it becomes very alkaline and can cause stress corrosion cracking (SCC) and pitting corrosion of the tank materials. SRS has experienced leakage from non-stress-relieved waste tanks constructed of A285 carbon steel and pitting of A212 carbon steel tanks in the vapor space. An investigation of tank materials has been undertaken at SRS to develop a basic understanding of caustic SCC of A285 and A212 grade carbon steels exposed to aqueous solutions, primarily containing sodium hydroxide (NaOH), sodium nitrate (NaNO{sub 3}), and sodium nitrite (NaNO{sub 2}) at temperatures relevant to the operating conditions of both the F and H area plants. This report presents the results of this corrosion testing program. Electrochemical tests were designed using unstressed coupons in a simulated tank environment. The purpose of this testing was to determine the corrosion susceptibility of the tank materials as a function of chemical concentration, pH, and temperature. A285 and A516 (simulates A212 carbon steel) coupons were used to investigate differences in the corrosion of these carbon steels. Electrochemical testing included measurement of the corrosion potential and polarization resistance as well as cyclic potentiodynamic polarization (CPP) testing of coupons. From the CPP experiments, corrosion characteristics were determined including: corrosion potential (E{sub corr}), pitting or breakdown potential (E{sub pit}), and repassivation potential (E{sub prot}). CPP results showed no indications of localized corrosion, such as pitting, and all samples showed the formation of a stable passive layer as evidenced by the positive

  20. Phase change in 080A42 plain carbon steel

    NASA Astrophysics Data System (ADS)

    de'Ath, James; Proud, William; Appleby-Thomas, Gareth; Millett, Jeremy

    2011-06-01

    Under shock loading conditions, mild steel undergoes a solid-solid phase transition at approximately 13GPa. In this work 080A42 plain carbon steel bright round rolled bar, was machined and heat-treated to produce an annealed or a martensitic structure. These samples were shock loaded, by plate impact, and the material response recorded using in-situ manganin stress gauges and heterodyne velocimetry. The Hugoniot stress and material characteristics both above and below the phase transition pressure have been recorded.

  1. Phase change in 080M40 plain carbon steel

    NASA Astrophysics Data System (ADS)

    De'Ath, James Michael; Proud, William; Millett, Jeremy; Appleby-Thomas, Gareth James

    2012-03-01

    Under shock loading conditions, mild steel undergoes a solid-solid phase transition at approximately 13GPa. In this work 080M40 plain carbon steel bright round rolled bar, was machined and heat-treated to produce an annealed or a martensitic structure. These samples were shock loaded, by plate impact, and the material response recorded using in-situ manganin stress gauges and heterodyne velocimetry. The Hugoniot stress and material characteristics both above and below the phase transition pressure have been recorded.

  2. Modeling the Electrical Contact Resistance at Steel-Carbon Interfaces

    NASA Astrophysics Data System (ADS)

    Brimmo, Ayoola T.; Hassan, Mohamed I.

    2016-01-01

    In the aluminum smelting industry, electrical contact resistance at the stub-carbon (steel-carbon) interface has been recurrently reported to be of magnitudes that legitimately necessitate concern. Mitigating this via finite element modeling has been the focus of a number of investigations, with the pressure- and temperature-dependent contact resistance relation frequently cited as a factor that limits the accuracy of such models. In this study, pressure- and temperature-dependent relations are derived from the most extensively cited works that have experimentally characterized the electrical contact resistance at these contacts. These relations are applied in a validated thermo-electro-mechanical finite element model used to estimate the voltage drop across a steel-carbon laboratory setup. By comparing the models' estimate of the contact electrical resistance with experimental measurements, we deduce the applicability of the different relations over a range of temperatures. The ultimate goal of this study is to apply mathematical modeling in providing pressure- and temperature-dependent relations that best describe the steel-carbon electrical contact resistance and identify the best fit relation at specific thermodynamic conditions.

  3. 75 FR 69125 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-10

    ... COMMISSION Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From China Determination... alloy steel standard, line, and pressure pipe (``seamless SLP pipe''), provided for in subheadings 7304... USITC Publication 4190 (November 2010), entitled Certain Seamless Carbon and Alloy Steel Standard,...

  4. A new nanoscale metastable iron phase in carbon steels

    NASA Astrophysics Data System (ADS)

    Liu, Tianwei; Zhang, Danxia; Liu, Qing; Zheng, Yanjun; Su, Yanjing; Zhao, Xinqing; Yin, Jiang; Song, Minghui; Ping, Dehai

    2015-10-01

    Metastable ω phase is common in body-centred cubic (bcc) metals and alloys, including high-alloying steels. Recent theoretical calculations also suggest that the ω structure may act as an intermediate phase for face-centred cubic (fcc)-to-bcc transformation. Thus far, the role of the ω phase played in fcc-bcc martensitic transformation in carbon steels has not been reported. In previous investigations on martensitic carbon steels, extra electron diffraction spots were frequently observed by transmission electron microscopy (TEM), and these spots were historically ascribed to the diffraction arising from either internal twins or carbides. In this paper, an intensive TEM investigation revealed that the extra spots are in fact attributed to the metastable ω phase in particle-like morphology with an overall size of several or dozens of nanometres. The strict orientation relationships between the ω phase and the ferrite matrix are in good agreement with those of the hexagonal (P6/mmm) ω phase in other bcc metals and alloys. The identification of the ω phase as well as the extra diffraction spots might provide a clue to help understand the physical mechanism of martensitic transformation in steels.

  5. A new nanoscale metastable iron phase in carbon steels.

    PubMed

    Liu, Tianwei; Zhang, Danxia; Liu, Qing; Zheng, Yanjun; Su, Yanjing; Zhao, Xinqing; Yin, Jiang; Song, Minghui; Ping, Dehai

    2015-10-27

    Metastable ω phase is common in body-centred cubic (bcc) metals and alloys, including high-alloying steels. Recent theoretical calculations also suggest that the ω structure may act as an intermediate phase for face-centred cubic (fcc)-to-bcc transformation. Thus far, the role of the ω phase played in fcc-bcc martensitic transformation in carbon steels has not been reported. In previous investigations on martensitic carbon steels, extra electron diffraction spots were frequently observed by transmission electron microscopy (TEM), and these spots were historically ascribed to the diffraction arising from either internal twins or carbides. In this paper, an intensive TEM investigation revealed that the extra spots are in fact attributed to the metastable ω phase in particle-like morphology with an overall size of several or dozens of nanometres. The strict orientation relationships between the ω phase and the ferrite matrix are in good agreement with those of the hexagonal (P6/mmm) ω phase in other bcc metals and alloys. The identification of the ω phase as well as the extra diffraction spots might provide a clue to help understand the physical mechanism of martensitic transformation in steels.

  6. A new nanoscale metastable iron phase in carbon steels

    PubMed Central

    Liu, Tianwei; Zhang, Danxia; Liu, Qing; Zheng, Yanjun; Su, Yanjing; Zhao, Xinqing; Yin, Jiang; Song, Minghui; Ping, Dehai

    2015-01-01

    Metastable ω phase is common in body-centred cubic (bcc) metals and alloys, including high-alloying steels. Recent theoretical calculations also suggest that the ω structure may act as an intermediate phase for face-centred cubic (fcc)-to-bcc transformation. Thus far, the role of the ω phase played in fcc-bcc martensitic transformation in carbon steels has not been reported. In previous investigations on martensitic carbon steels, extra electron diffraction spots were frequently observed by transmission electron microscopy (TEM), and these spots were historically ascribed to the diffraction arising from either internal twins or carbides. In this paper, an intensive TEM investigation revealed that the extra spots are in fact attributed to the metastable ω phase in particle-like morphology with an overall size of several or dozens of nanometres. The strict orientation relationships between the ω phase and the ferrite matrix are in good agreement with those of the hexagonal (P6/mmm) ω phase in other bcc metals and alloys. The identification of the ω phase as well as the extra diffraction spots might provide a clue to help understand the physical mechanism of martensitic transformation in steels. PMID:26503890

  7. Methods for the Identification of Aircraft Tubing of Plain Carbon Steel and Chromium-Molybdenum Steel

    NASA Technical Reports Server (NTRS)

    Mutchler, W H; Buzzard, R W

    1930-01-01

    The survey of the possibilities for distinguishing between plain carbon and chromium-molybdenum steel tubing included the Herbert pendulum hardness, magnetic, sparks, and chemical tests. The Herbert pendulum test has the disadvantages of all hardness tests in being limited to factory use and being applicable only to scale-free, normalized material. The small difference in the range of hardness values between plain carbon and chromium-molybdenum steels is likewise a disadvantage. The Rockwell hardness test, at present used in the industry for this purpose, is much more reliable. It may be concluded on the basis of the experiments performed that of all methods surveyed, spark testing appears to be, at present, the most suitable for factory use from the standpoint of speed, accuracy, nondestructiveness and reliability. It is also applicable for field use.

  8. Corrosion of carbon steel substrate under alloy C-276 wallpaper

    SciTech Connect

    Caudill, D.L.; Koch, G.H.

    1996-08-01

    Flue gas desulfurization (FGD) systems or wet scrubbers are essentially chemical plants, which are used to reduce sulfur dioxide (SO{sub 2}) emissions from coal fired power plants. The most common process involves wet limestone scrubbing. The scrubbed flue gas is discharged from the scrubber modules into an outlet duct that leads into the stack. The scrubbed flue gas enters the outlet duct at its adiabatic saturation temperature and, as a result, a considerable amount of condensation occurs on the duct walls. The condensate usually contains various mineral acids and many dissolved ions, which makes the condensate very corrosive. Following start up of two FGD systems, leaks were experienced in the welds of the C-276 wallpaper. In order to address the concern that absorber liquid or outlet duct condensate would cause unacceptable corrosion of the carbon steel shell, laboratory experiments were conducted. The results of these experiments demonstrated the indeed under certain conditions, significant corrosion of the carbon steel could occur.

  9. The effect of gamma radiation on reference electrodes and platinum and carbon steel bare metal electrodes in a simulated waste solution. Final report

    SciTech Connect

    Danielson, M.J.

    1993-09-01

    Electrochemical potential measurements of materials in waste tanks are important in determining if the materials have a propensity for stress corrosion cracking and pitting. Potential measurement requires a reference electrode, but the effect of radiation on the potential generated by the reference electrode has been an unknown quantity. To determine the significance of the radiation effect, Pacific Northwest Laboratory conducted studies of five types of electrodes under gamma radiation at room temperature. The subjects were two types of silver/silver chloride reference electrodes (Fisher and Lazaran), a mercury/calomel reference electrode, a platinum ``flag,`` and a piece of A-537 carbon steel; the electrodes were exposed to a simulated caustic tank environment. The Fisher silver/silver chloride and mercury/calomel reference electrodes showed essentially no radiation effects up to a flux of 2.1E6 R/h and fluence of 9.4E8 R, indicating they would be useful reference electrodes for in-tank studies. The Lazaran{reg_sign} silver/silver chloride electrode showed serious potential deviations at fluences of 2.E8 R, but it would be the electrode of choice in many situations because it is simple to maintain. Radiation affected the open circuit potential of both the platinum and carbon steel electrodes. This effect indicates that corrosion studies without radiation may not duplicate the corrosion processes expected in a waste tank. Mixed-potential theory was used to explain the radiation effects.

  10. Influence of carbon steel grade on the initial attachment of bacteria and microbiologically influenced corrosion.

    PubMed

    Javed, M A; Neil, W C; Stoddart, P R; Wade, S A

    2016-01-01

    The influence of the composition and microstructure of different carbon steel grades on the initial attachment (≤ 60 min) of Escherichia coli and subsequent longer term (28 days) corrosion was investigated. The initial bacterial attachment increased with time on all grades of carbon steel. However, the rate and magnitude of bacterial attachment varied on the different steel grades and was significantly less on the steels with a higher pearlite phase content. The observed variations in the number of bacterial cells attached across different steel grades were significantly reduced by applying a fixed potential to the steel samples. Longer term immersion studies showed similar levels of biofilm formation on the surface of the different grades of carbon steel. The measured corrosion rates were significantly higher in biotic conditions compared to abiotic conditions and were found to be positively correlated with the pearlite phase content of the different grades of carbon steel coupons.

  11. Diffusion Saturation of Carbon Steel Under Microarc Heating

    NASA Astrophysics Data System (ADS)

    Stepanov, M. S.; Dombrovskii, Yu. M.; Pustovoit, V. N.

    2017-05-01

    Microarc thermochemical treatment (MTCT) is suggested for intensification of diffusion saturation of the surface layer of steel articles. The hardened article is immersed into powdered mineral coal and heated by passed electric current. The main stages of the MTCT process are determined. The diffusion layer is shown to be accelerated by carburizing. High-hardness coatings are obtained due to simultaneous diffusion of carbon, chromium, molybdenum and boron.

  12. CMT Welding of Low Carbon Steel Thin Sheets

    NASA Astrophysics Data System (ADS)

    Stanciu, E. M.; Pascu, A.; Gheorghiu, I.

    2017-06-01

    This paper addresses to the cold metal transfer MAG welding of low carbon steel thin sheets. The paper highlights the advantages of using CMT process for but joining of S235 carbon sheets by comparing the CMT with the conventional synergic pulse MAG welding. A lower weld bead area and heat affected zone is obtained by the continuous movement of the wire, digitally synchronised with the short-circuit of the arc. CMT welding can produce good welds even in unfavorable conditions, such as using thin plates and high diameter wire.

  13. 76 FR 27987 - Circular Welded Carbon Steel Pipes and Tubes From Thailand: Amended Final Results of Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-13

    ... International Trade Administration Circular Welded Carbon Steel Pipes and Tubes From Thailand: Amended Final... on circular welded carbon steel pipes and tubes from Thailand, which covered Saha Thai Steel Pipe... Welded Carbon Steel Pipes and Tubes from Thailand: Final Results of Antidumping Duty...

  14. 75 FR 4779 - Certain Cut-to-Length Carbon-Quality Steel Plate Products From Italy: Preliminary Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-29

    ... International Trade Administration Certain Cut-to-Length Carbon-Quality Steel Plate Products From Italy... duty order on certain cut-to-length carbon- quality steel plate products from Italy. This review covers... antidumping duty order on certain cut-to-length carbon- quality steel plate products (steel plate) from...

  15. 75 FR 64254 - Certain Hot-Rolled Flat-Rolled Carbon Quality Steel Products From Brazil; Final Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-19

    ... International Trade Administration Certain Hot-Rolled Flat-Rolled Carbon Quality Steel Products From Brazil... order on certain hot-rolled, flat-rolled carbon quality steel products (hot-rolled steel) from Brazil. See Certain Hot- Rolled Flat-Rolled Carbon Quality Steel Products From Brazil: Preliminary Results of...

  16. 76 FR 42679 - Certain Hot-Rolled Carbon Steel Flat Products From India: Final Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-19

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From India: Final Results of... certain hot- rolled carbon steel flat products from India manufactured by Essar Steel Limited (``Essar...\\ of this review. \\2\\ See Certain Hot-Rolled Carbon Steel Flat Products From India: Notice...

  17. Metallurgical Mechanism and Niobium Effects on Improved Mechanical Properties in High Carbon Steels

    NASA Astrophysics Data System (ADS)

    Jansto, Steven G.

    The technological development of value-added applications for niobium (Nb) microalloyed structural steels has expanded into the high carbon long products sector. Micro additions of 0.005 to 0.020%Nb in various high carbon steel compositions have exhibited improved processing, such as wire drawability or formability during manufacturing, higher productivity at reduced operational cost as well as improved mechanical properties compared to traditional non-Nb bearing high carbon steels. Although the Nb solubility is limited in high carbon steels compared to low carbon steels, the optimized Nb content has been defined based on experimental results and now transferred into industrial operations. The Nb delays the pearlite transformation, hence resulting in a finer interlammelar spacing compared to traditional high carbon pearlitic steels. Consequently, the optimized Nb content leads to improved mechanical properties due to this finer interlamellar pearlite spacing. Opportunities exist to transfer this new Nb-technology into wire rods, bolts, rails and tire cord.

  18. 75 FR 16439 - Certain Welded Carbon Steel Standard Pipe From Turkey: Preliminary Results of Countervailing Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-01

    ... Countervailing Duty Administrative Review AGENCY: Import Administration, International Trade Administration... review of the countervailing duty (CVD) order on certain welded carbon steel standard pipe from Turkey... carbon steel pipe and tube products from Turkey. See Countervailing Duty Order: Certain Welded Carbon...

  19. 77 FR 54926 - Certain Seamless Carbon and Alloy Steel; Standard, Line, and Pressure Pipe From Germany

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-06

    ... COMMISSION Certain Seamless Carbon and Alloy Steel; Standard, Line, and Pressure Pipe From Germany... U.S.C. 1675(c)), that revocation of the antidumping duty order on certain seamless carbon and alloy... 2012), entitled Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe from...

  20. Investigation of carbon segregation during low temperature tempering in a medium carbon steel

    SciTech Connect

    Xiao, Y.; Li, W.; Zhao, H.S.; Lu, X.W.; Jin, X.J.

    2016-07-15

    Low temperature tempering is important in improving the mechanical properties of steels. In this study, the thermoelectric power method was employed to investigate carbon segregation during low temperature tempering ranging from 110 °C to 170 °C of a medium carbon alloyed steel, combined with micro-hardness, transmission electron microscopy and atom probe tomography. Evolution of carbon dissolution from martensite and segregation to grain boundaries/interfaces and dislocations were investigated for different tempering conditions. Carbon concentration variation was quantified from 0.33 wt.% in quenching sample to 0.15 wt.% after long time tempering. The kinetic of carbon diffusion during tempering process was discussed through Johnson-Mehl-Avrami equation. - Highlights: • The thermoelectric power (TEP) was employed to investigate the low temperature tempering of a medium carbon alloyed steel. • Evolution of carbon dissolution was investigated for different tempering conditions. • Carbon concentration variation was quantified from 0.33 wt.% in quenching sample to 0.15 wt.% after long time tempering.

  1. Microstructure and high temperature properties of the dissimilar weld between ferritic stainless steel and carbon steel

    NASA Astrophysics Data System (ADS)

    Kim, Jeong Kil; Hong, Seung Gab; Kang, Ki Bong; Kang, Chung Yun

    2009-10-01

    Dissimilar joints between STS441, a ferritic stainless steel, and SS400, a carbon steel, were welded by GMAW (Gas Metal Arc Welding) using STS430LNb as a welding wire. The fracture behavior of the dissimilar weld was analyzed by a microstructural observation and thermo-mechanical tests. Martensite was formed at the region between SS400 and the weld metal because the Cr and Nb content in this region decreased due to the dilution of SS400 carbon steel during welding. According to results from a high temperature tensile test with a specimen aged at 900 °C, it was found that the tensile strength of the dissimilar weld at high temperature was equal to that of STS441 base metal and the formation of martensite had little influence on tensile strength of the dissimilar weld at high temperature. However, in the case of thermal fatigue resistance, the dissimilar weld had an inferior thermal fatigue life to STS441 because of the presence of martensite and the softened region around the interface between the dissimilar weld metal and SS400.

  2. Boriding of high carbon high chromium cold work tool steel

    NASA Astrophysics Data System (ADS)

    Muhammad, W.

    2014-06-01

    High-carbon high-chromium cold work tool steels are widely used for blanking and cold forming of punches and dies. It is always advantageous to obtain an increased wear resistant surface to improve life and performance of these steels. In this connection boriding of a high-carbon high-chromium cold work die steel, D3, was conducted in a mixture of 30% B4C, 70% borax at 950 °C for two, four and six hours. Case depth of the borided layer obtained was between 40 to 80 μm. After boriding, the surface hardness achieved was between 1430 to 1544 HV depending upon the process time. X-ray diffraction studies confirmed the formation of a duplex compound layer consisting of FeB and Fe2B. It is generally considered that FeB is undesirable because of its inherent brittleness. Post boriding treatment (homogenization) transformed the compound layer into single-phase layer of Fe2B, while surface hardness decreased to 1345-1430 HV. Pin-on-disc wer test showed that wear resistance of the borided samples was superior as compared to non-borided material and increased with boriding time.

  3. Accelerated carbonation of steel slags in a landfill cover construction

    SciTech Connect

    Diener, S.; Andreas, L.; Herrmann, I.; Ecke, H.; Lagerkvist, A.

    2010-01-15

    Steel slags from high-alloyed tool steel production were used in a full scale cover construction of a municipal solid waste (MSW) landfill. In order to study the long-term stability of the steel slags within the final cover, a laboratory experiment was performed. The effect on the ageing process, due to i.e. carbonation, exerted by five different factors resembling both the material characteristics and the environmental conditions is investigated. Leaching behaviour, acid neutralization capacity and mineralogy (evaluated by means of X-ray diffraction, XRD, and thermogravimetry/differential thermal analysis, TG/DTA) are tested after different periods of ageing under different conditions. Samples aged for 3 and 10 months were evaluated in this paper. Multivariate data analysis was used for data evaluation. The results indicate that among the investigated factors, ageing time and carbon dioxide content of the atmosphere were able to exert the most relevant effect. However, further investigations are required in order to clarify the role of the temperature.

  4. TENSILE TESTING OF CARBON STEEL IN HIGH PRESSURE HYDROGEN

    SciTech Connect

    Duncan, A; Thad Adams, T; Ps Lam, P

    2007-05-02

    An infrastructure of new and existing pipelines and systems will be required to carry and to deliver hydrogen as an alternative energy source under the hydrogen economy. Carbon and low alloy steels of moderate strength are currently used in hydrogen delivery systems as well as in the existing natural gas systems. It is critical to understand the material response of these standard pipeline materials when they are subjected to pressurized hydrogen environments. The methods and results from a testing program to quantify hydrogen effects on mechanical properties of carbon steel pipeline and pipeline weld materials are provided. Tensile properties of one type of steel (A106 Grade B) in base metal, welded and heat affected zone conditions were tested at room temperature in air and high pressure (10.34 MPa or 1500 psig) hydrogen. A general reduction in the materials ability to plastically deform was noted in this material when specimens were tested in hydrogen. Furthermore, the primary mode of fracture was changed from ductile rupture in air to cleavage with secondary tearing in hydrogen. The mechanical test results will be applied in future analyses to evaluate service life of the pipelines. The results are also envisioned to be part of the bases for construction codes and structural integrity demonstrations for hydrogen service pipeline and vessels.

  5. MECHANICAL TESTING OF CARBON STEEL IN HIGH PRESSURE HYDROGEN

    SciTech Connect

    Duncan, A

    2006-05-11

    The methods and interim results from a testing program to quantify hydrogen effects on mechanical properties of carbon steel pipeline and pipeline weld materials are provided. The scope is carbon steels commonly used for natural gas pipelines in the United States that are candidates for hydrogen service in the hydrogen economy. The mechanical test results will be applied in future analyses to evaluate service life of the pipelines. The results are also envisioned to be part of the bases for construction codes and structural integrity demonstrations for hydrogen service pipeline and vessels. Tensile properties of one type of steel (A106 Grade B) in base metal, welded and heat affected zone conditions were tested at room temperature in air and high pressure (1500 psig) hydrogen. A general reduction in the materials ability to plastically deform was noted in this material when specimens were tested in 1500 psig hydrogen. Furthermore, the primary mode of fracture was changed from ductile rupture in air to cleavage with secondary tearing in hydrogen. The mechanical test program will continue with tests to quantify the fracture behavior in terms of J-R curves for these materials at air and hydrogen pressure conditions.

  6. Carbon determination in carbon-manganese steels under atmospheric conditions by Laser-Induced Breakdown Spectroscopy.

    PubMed

    Labutin, Timur A; Zaytsev, Sergey M; Popov, Andrey M; Zorov, Nikita B

    2014-09-22

    The most sensitive lines of carbon, used nowadays for its determination in steels by laser-induced-breakdown spectroscopy (LIBS), are at vacuum UV and, thereby, LIBS potential is significantly reduced. We suggested the use of the C I 833.51 nm line for carbon determination in low-alloy steels (c(C)~0.186-1.33 wt.%) in air. Double-pulse LIBS with the collinear scheme was performed for maximal enhancement of a carbon emission signal without substantial complication of experimental setup. Since this line is strongly broadened in laser plasma, it overlapped with the closest iron lines greatly. We implemented a PCR method for the construction of a multivariate calibration model under spectral interferences. The model provided a RMSECV = 0.045 wt.%. The predicted carbon content in the rail templet was in an agreement with the reference value obtained by a combustion analyzer within the relative error of 6%.

  7. A Spray Pyrolysis Method to Grow Carbon Nanotubes on Carbon Fibres, Steel and Ceramic Bricks.

    PubMed

    Vilatela, Juan J; Rabanal, M E; Cervantes-Sodi, Felipe; García-Ruiz, Máximo; Jiménez-Rodríguez, José A; Reiband, Gerd; Terrones, Mauricio

    2015-04-01

    We demonstrate a spray pyrolysis method to grow carbon nanotubes (CNTs) with high degree of crystallinity, aspect ratio and degree of alignment on a variety of different substrates, such as conventional steel, carbon fibres (CF) and ceramics. The process consists in the chemical vapour deposition of both a thin SiO2 layer and CNTs that subsequently grow on this thin layer. After CNT growth, increases in specific surface by factors of 1000 and 30 for the steel and CF samples, respectively, are observed. CNTs growth on ceramic surfaces results in a surface resistance of 37.5 Ohm/sq. When using conventional steel as a rector tube, we observed CNTs growth rates of 0.6 g/min. Details of nanotube morphology and the growth mechanism are discussed. Since the method discussed here is highly versatile, it opens up a wide variety of applications in which specific substrates could be used in combination with CNTs.

  8. Reduction of work hardening rate in low-carbon steels

    NASA Astrophysics Data System (ADS)

    Yalamanchili, Bhaskar Rao

    Low carbon grades of steel rods are used to produce finished products such as fine wire, coat hangers, staples, and roofing nails. These products are subject to ductility failures during production due to excessively high work hardening rates during wire drawing. The high work hardening rates are attributed to the presence of residuals, free nitrogen, or combinations thereof. This research concludes that the most cost-effective way to reduce the work hardening rate during wire drawing is to combine boron with nitrogen to form boron nitride, and thus reducing its work hardening contribution. The results of this study also conclude the following: (1) Boron/Nitrogen ratio is the more significant factor than rod tensile strength, which affects work hardening rate. Higher ratio is better in the 0.79 to 1.19 range. (2) Maintaining this narrow B/N range requires precise process control. (3) Process conditions such as dissolved oxygen (<25 ppm), carbon (≤0.05%) and ladle refining temperature (<2930°F) are necessary for optimizing boron recovery. (4) An average of 89% boron recovery is obtained with the above controlled process conditions. (5) Use of Boron has no adverse effects on the several metallurgical properties tested except with minor difficulty with scale for descaling. North Star Steel Texas (North Star) benefited from this research by being able to provide a competitive edge in both quality and cost of its low carbon boron grades thus making North Star a preferred supplier of wire rod for these products.

  9. Passivity and breakdown of carbon steel in organic solvent mixtures of propylene carbonate and dimethoxyethane

    SciTech Connect

    Shifler, D.A.; Kruger, J.; Moran, P.J.

    1998-07-01

    The passivity and breakdown of passivity of 1018 carbon steel in propylene carbonate (PC) and 1,2-dimethoxyethane (DME) mixtures with 0.5 molar lithium hexafluoroarsenate supporting electrolyte were examined via several electrochemical and surface analytical methods. The PC-DME/0.5 M LiAsF{sub 6} mixtures ranged from 10 to 90 mol % PC. The results from the PC/DME mixtures were compared to passivating mechanisms found in pure PC and DME solutions. In PC-rich mixtures, the breakdown of passivity occurred near the oxidation potentials of either organic solvent. Premature breakdown of the carbon steel in PC-DME mixtures occurred at sulfide inclusions as was observed earlier in PC/0.5 M LiAsF{sub 6} solutions although passive films attempted to form at these inclusion sites in mixtures containing at least 10 mol % DME. As the DME content increased in the PC-DME mixtures, the passive films formed on bare steel surfaces possessed an increasing polymer film character. In 50 and 70 mol % DME solutions nonprotective polymer films were formed. The nonprotective nature of these films indicated that PC passivation mechanisms competed and interfered with the DME mechanism of electropolymerized film formation. Only in 10 mol % PC-90 mol % DME mixtures were protective electropolymerized films formed on 1018 carbon steel.

  10. Friction stir processing on high carbon steel U12

    SciTech Connect

    Tarasov, S. Yu. Rubtsov, V. E.; Melnikov, A. G.

    2015-10-27

    Friction stir processing (FSP) of high carbon steel (U12) samples has been carried out using a milling machine and tools made of cemented tungsten carbide. The FSP tool has been made in the shape of 5×5×1.5 mm. The microstructural characterization of obtained stir zone and heat affected zone has been carried out. Microhardness at the level of 700 MPa has been obtained in the stir zone with microstructure consisting of large grains and cementitte network. This high-level of microhardness is explained by bainitic reaction developing from decarburization of austenitic grains during cementite network formation.

  11. Kinetics of electrochemical boriding of low carbon steel

    NASA Astrophysics Data System (ADS)

    Kartal, G.; Eryilmaz, O. L.; Krumdick, G.; Erdemir, A.; Timur, S.

    2011-05-01

    In this study, the growth kinetics of the boride layers forming on low carbon steel substrates was investigated during electrochemical boriding which was performed at a constant current density of 200 mA/cm 2 in a borax based electrolyte at temperatures ranging from 1123 K to 1273 K for periods of 5-120 min. After boriding, the presence of both FeB and Fe 2B phases were confirmed by the X-ray diffraction method. Cross-sectional microscopy revealed a very dense and thick morphology for both boride phases. Micro hardness testing of the borided steel samples showed a significant increase in the hardness of the borided surfaces (i.e., up to (1700 ± 200) HV), while the hardness of un-borided steel samples was approximately (200 ± 20) HV. Systematic studies over a wide range of boriding time and temperature confirmed that the rate of the boride layer formation is strongly dependent on boriding duration and has a parabolic character. The activation energy of boride layer growth for electrochemical boriding was determined as (172.75 ± 8.6) kJ/mol.

  12. Hydrogen attack - Influence of hydrogen sulfide. [on carbon steel

    NASA Technical Reports Server (NTRS)

    Eliezer, D.; Nelson, H. G.

    1978-01-01

    An experimental study is conducted on 12.5-mm-thick SAE 1020 steel (plain carbon steel) plate to assess hydrogen attack at room temperature after specimen exposure at 525 C to hydrogen and a blend of hydrogen sulfide and hydrogen at a pressure of 3.5 MN/sq m for exposure times up to 240 hr. The results are discussed in terms of tensile properties, fissure formation, and surface scales. It is shown that hydrogen attack from a high-purity hydrogen environment is severe, with the formation of numerous methane fissures and bubbles along with a significant reduction in the room-temperature tensile yield and ultimate strengths. However, no hydrogen attack is observed in the hydrogen/hydrogen sulfide blend environment, i.e. no fissure or bubble formation occurred and the room-temperature tensile properties remained unchanged. It is suggested that the observed porous discontinuous scale of FeS acts as a barrier to hydrogen entry, thus reducing its effective equilibrium solubility in the iron lattice. Therefore, hydrogen attack should not occur in pressure-vessel steels used in many coal gasification processes.

  13. 76 FR 12322 - Certain Cut-to-Length Carbon-Quality Steel Plate From India, Indonesia, Italy, Japan, and the...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-07

    ... ASTM A710 and A736 or their proprietary equivalents; (4) abrasion-resistant steels (i.e., USS AR 400... equivalents; (6) ball bearing steels; (7) tool steels; and (8) silicon manganese steel or silicon electric... International Trade Administration Certain Cut-to-Length Carbon-Quality Steel Plate From India, Indonesia,...

  14. 78 FR 46570 - Suspension Agreement on Certain Cut-to-Length Carbon Steel Plate From Ukraine; Administrative Review

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-01

    ... International Trade Administration Suspension Agreement on Certain Cut-to-Length Carbon Steel Plate From Ukraine... & Steel Works (Azovstal) and Ilyich Iron and Steel Works (Ilyich), are in compliance with the agreement suspending the antidumping investigation of certain cut-to-length carbon steel plate (CTL plate) from...

  15. 76 FR 31938 - Certain Hot-Rolled Carbon Steel Flat Products From India: Notice of Preliminary Results of 2009...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-02

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From India: Notice of... antidumping duty order on certain hot-rolled carbon steel flat products from India (``hot-rolled steel... on Indian hot-rolled steel. See Notice of Amended Final Antidumping Duty Determination of Sales at...

  16. 75 FR 65453 - Certain Hot-Rolled Flat-Rolled Carbon Quality Steel Flat Products From Brazil: Notice of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-25

    ... International Trade Administration Certain Hot-Rolled Flat-Rolled Carbon Quality Steel Flat Products From Brazil... duty order on certain hot-rolled flat-rolled carbon quality steel flat products (hot-rolled steel) from Brazil. The review covers four producers/exporters of hot-rolled steel from Brazil, all mandatory...

  17. Stress corrosion cracking of X-60 line pipe steel in a carbonate-bicarbonate solution

    SciTech Connect

    Pilkey, A.K.; Lambert, S.B.; Plumtree, A. . Dept. of Mechanical Engineering)

    1995-02-01

    An experimental system was developed to reproduce stress corrosion cracking (SCC) of API X-60 line pipe steels in highly alkaline (pH = 10) carbonate-bicarbonate (1 N sodium carbonate [Na[sub 2]CO[sub 3

  18. AISI/DOE Technology Roadmap Program: Effects of Residuals in Carbon Steels

    SciTech Connect

    George E. Ruddle

    2002-11-25

    AN experimental study of the effects of residual elements in carbon steels was carried out to gain better understanding and control of the effects of residual elements emanating from recycled steel scrap. Two plain carbon steel grade compositions (one medium-carbon and one low-carbon), residual elements and levels, and four areas of study, were selected on the bases of a comprehensive literature survey and consultation with sponsor steel companies. The influence of residuals (Cu, Sn, Ni, P, Si, up to the levels studied here), on these laboratory produced hot rolled steels was studied in the areas of (a) hot ductility, (b) surface hot shortness, (c) scale formation and adherence, and (d) embrittlement and mechanical properties. This report summarizes the experimental procedures, results, discussion and conclusions of this study. The relevance of the study is also discussed in relation to steel processing and product properties and in relation to energy consumption and environmental compliance.

  19. Efficiency of inhibitor for biocorrosion influenced by consortium sulfate reducing bacteria on carbon steel

    NASA Astrophysics Data System (ADS)

    Mahat, Nur Akma; Othman, Norinsan Kamil; Sahrani, Fathul Karim

    2015-09-01

    The inhibition efficiency of benzalkonium chloride (BKC) in controlling biocorrosion on the carbon steel surfaces has been investigated. The carbon steel coupons were incubated in the presence of consortium SRB (C-SRB) with and without BKC for the difference medium concentration. The corrosion rate and inhibition efficiency have been evaluated by a weight loss method. The morphology of biofilm C-SRB on the steel surfaces were characterized with variable pressure scanning electron microscopy (VPSEM). The results revealed that BKC exhibits a low corrosion rate, minimizing the cell growth and biofilm development on the carbon steel surfaces.

  20. Efficiency of inhibitor for biocorrosion influenced by consortium sulfate reducing bacteria on carbon steel

    SciTech Connect

    Mahat, Nur Akma; Othman, Norinsan Kamil; Sahrani, Fathul Karim

    2015-09-25

    The inhibition efficiency of benzalkonium chloride (BKC) in controlling biocorrosion on the carbon steel surfaces has been investigated. The carbon steel coupons were incubated in the presence of consortium SRB (C-SRB) with and without BKC for the difference medium concentration. The corrosion rate and inhibition efficiency have been evaluated by a weight loss method. The morphology of biofilm C-SRB on the steel surfaces were characterized with variable pressure scanning electron microscopy (VPSEM). The results revealed that BKC exhibits a low corrosion rate, minimizing the cell growth and biofilm development on the carbon steel surfaces.

  1. Distribution of radionuclides during melting of carbon steel

    SciTech Connect

    Thurber, W.C.; MacKinney, J.

    1997-02-01

    During the melting of steel with radioactive contamination, radionuclides may be distributed among the metal product, the home scrap, the slag, the furnace lining and the off-gas collection system. In addition, some radionuclides will pass through the furnace system and vent to the atmosphere. To estimate radiological impacts of recycling radioactive scrap steel, it is essential to understand how radionuclides are distributed within the furnace system. For example, an isotope of a gaseous element (e.g., radon) will exhaust directly from the furnace system into the atmosphere while a relatively non-volatile element (e.g., manganese) can be distributed among all the other possible media. This distribution of radioactive contaminants is a complex process that can be influenced by numerous chemical and physical factors, including composition of the steel bath, chemistry of the slag, vapor pressure of the particular element of interest, solubility of the element in molten iron, density of the oxide(s), steel melting temperature and melting practice (e.g., furnace type and size, melting time, method of carbon adjustment and method of alloy additions). This paper discusses the distribution of various elements with particular reference to electric arc furnace steelmaking. The first two sections consider the calculation of partition ratios for elements between metal and slag based on thermodynamic considerations. The third section presents laboratory and production measurements of the distribution of various elements among slag, metal, and the off-gas collection system; and the final section provides recommendations for the assumed distribution of each element of interest.

  2. Heavy reflector experiments in the IPEN/MB-01 reactor: Stainless steel, carbon steel and nickel

    SciTech Connect

    Santos, Adimir dos; Andrade e Silva, Graciete Simoes de; Jerez, Rogerio; Liambos Mura, Luis Felipe; Fuga, Rinaldo

    2013-05-06

    New experiments devoted to the measurements of physical parameters of a light water core surrounded by a heavy reflector were performed in the IPEN/MB-01 research reactor facility. These experiments comprise three sets of heavy reflector (SS-304, Carbon Steel, and Nickel) in a form of laminates around 3 mm thick. Each set was introduced individually in the west face of the core of the IPEN/MB-01 reactor. The aim here is to provide high quality experimental data for the interpretation and validation of the SS-304 heavy reflector calculation methods. The experiments of Carbon Steel, which is composed mainly of iron, and Nickel were performed to provide a consistent and an interpretative check for the SS-304 reflector experiment. The experimental results comprise critical control bank positions, temperatures and reactivities as a function of the number of the plates. Particularly to the case of Nickel, the experimental data are unique of its kind. The theoretical analysis was performed by MCNP-5 with the nuclear data library ENDF/B-VII.0. It was shown that this nuclear data library has a very good performance up to thirteen plates and overestimates the reactivity for higher number of plates independently of the type of the reflector.

  3. Fracture Behavior of Ultra-Low-Carbon Steel Plate and Heat-Affected-Zone.

    DTIC Science & Technology

    1990-12-01

    ganese-molybdenum steel caused an increase in the DBTT . However. it cannot be assumed that the presence of these TiN cubes always causes detrimental...Department Research & Development Report 0 N Fracture Behavior of Ultra-Low-Carbon Steel Plate and Heat-Affected-Zone by M. G. Vassilaros CO a- Co -e DTIC...Materials Engineering Department Research & Development Report Fracture Behavior of Ultra-Low-Carbon Steel Plate and Heat-Affected-Zone by M. G

  4. 78 FR 21105 - Circular Welded Carbon Steel Pipes and Tubes From Thailand: Preliminary Results of Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-09

    ... International Trade Administration Circular Welded Carbon Steel Pipes and Tubes From Thailand: Preliminary... tubes from Thailand. This review covers two producers/exporters of the subject merchandise, Saha Thai... The products covered by the antidumping order are certain circular welded carbon steel pipes and...

  5. 75 FR 21658 - Carbon and Certain Alloy Steel Wire Rod From Trinidad and Tobago

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-26

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Carbon and Certain Alloy Steel Wire Rod From Trinidad and Tobago AGENCY: United States... in the antidumping duty Investigation No. 731-TA-961 concerning carbon and certain alloy steel...

  6. 48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate....

  7. 48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate....

  8. 48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 3 2014-10-01 2014-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate....

  9. 48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate....

  10. 48 CFR 225.7011 - Restriction on carbon, alloy, and armor steel plate.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Restriction on carbon, alloy, and armor steel plate. 225.7011 Section 225.7011 Federal Acquisition Regulations System DEFENSE... on carbon, alloy, and armor steel plate....

  11. 78 FR 2658 - Carbon and Certain Alloy Steel Wire Rod From Mexico: Rescission of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-14

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE International Trade Administration Carbon and Certain Alloy Steel Wire Rod From Mexico: Rescission of... its administrative review of the antidumping duty order on carbon and certain alloy steel wire...

  12. Marine Atmospheric Corrosion of Carbon Steel: A Review

    PubMed Central

    Alcántara, Jenifer; de la Fuente, Daniel; Chico, Belén; Simancas, Joaquín; Díaz, Iván; Morcillo, Manuel

    2017-01-01

    The atmospheric corrosion of carbon steel is an extensive topic that has been studied over the years by many researchers. However, until relatively recently, surprisingly little attention has been paid to the action of marine chlorides. Corrosion in coastal regions is a particularly relevant issue due the latter’s great importance to human society. About half of the world’s population lives in coastal regions and the industrialisation of developing countries tends to concentrate production plants close to the sea. Until the start of the 21st century, research on the basic mechanisms of rust formation in Cl−-rich atmospheres was limited to just a small number of studies. However, in recent years, scientific understanding of marine atmospheric corrosion has advanced greatly, and in the authors’ opinion a sufficient body of knowledge has been built up in published scientific papers to warrant an up-to-date review of the current state-of-the-art and to assess what issues still need to be addressed. That is the purpose of the present review. After a preliminary section devoted to basic concepts on atmospheric corrosion, the marine atmosphere, and experimentation on marine atmospheric corrosion, the paper addresses key aspects such as the most significant corrosion products, the characteristics of the rust layers formed, and the mechanisms of steel corrosion in marine atmospheres. Special attention is then paid to important matters such as coastal-industrial atmospheres and long-term behaviour of carbon steel exposed to marine atmospheres. The work ends with a section dedicated to issues pending, noting a series of questions in relation with which greater research efforts would seem to be necessary. PMID:28772766

  13. Boric acid corrosion of carbon and low alloy steels

    SciTech Connect

    Campbell, C.A.; Fyfitch, S.; Martin, D.T.

    1994-12-31

    Leakage of borated water from the reactor coolant system of pressurized water reactors (PWRs) and the resulting corrosion of carbon and low alloy steel components are concerns that have been addressed by utilities for many years. Significant corrosion has been observed in instances where such leakage has gone undetected for several months. In 1990, the B and W Owners Group (B and WOG) sponsored a test program to determine the levels of wastage that are possible when primary water leakage occurs. In this test program, carbon and stainless steel specimens were exposed to borated water at temperatures from 300 F to 550 F. Initial boric acid concentration was controlled within the limits of 13,000 to 15,000 ppm (as H{sub 3}BO{sub 3}) with 1.0--2.0 ppm lithium (as LiOH) added to duplicate the primary water chemistry. Testing was performed to determine the degree of attack caused by a leak traveling along a pipe both with and without insulation. These tests show the importance of temperature and boric acid concentrations on the wastage that can occur from such a leak.

  14. Raising the Corrosion Resistance of Low-Carbon Steels by Electrolytic-Plasma Saturation with Nitrogen and Carbon

    NASA Astrophysics Data System (ADS)

    Kusmanov, S. A.; Grishina, E. P.; Belkin, P. N.; Kusmanova, Yu. V.; Kudryakova, N. O.

    2017-05-01

    Structural features of the external oxide layer and internal nitrided, carbonitrided and carburized layers in steels 10, 20 and St3 produced by the method of electrolytic plasma treatment are studied. Specimens of the steels are tested for corrosion in a naturally aerated 1-N solution of sodium chloride. The condition of the metal/sodium chloride solution interface is studied by the method of electrochemical impedance spectroscopy. It is shown that the corrosion resistance of low-carbon steels can be raised by anode electrolytic-plasma saturation with nitrogen and carbon. Recommendations are given on the choice of carbonitriding modes for structural steels.

  15. Characterization of the Carbon and Retained Austenite Distributions in Martensitic Medium Carbon, Low Alloy, Steel

    SciTech Connect

    Sherman, D. H.; Cross, Steven M; Kim, Sangho; Grandjean, F.; Long, G. J.; Miller, Michael K

    2007-01-01

    The retained austenite content and carbon distribution in martensite were determined as a function of cooling rate and temper temperature in steel that contained 1.31 at. pct C, 3.2 at. pct Si, and 3.2 at. pct non-iron metallic elements. Mossbauer spectroscopy, transmission electron microscopy (TEM), transmission synchrotron X-ray diffraction (XRD), and atom probe tomography were used for the microstructural analyses. The retained austenite content was an inverse, linear function of cooling rate between 25 and 560 K/s. The elevated Si content of 3.2 at. pct did not shift the start of austenite decomposition to higher tempering temperatures relative to SAE 4130 steel. The minimum tempering temperature for complete austenite decomposition was significantly higher (>650 C) than for SAE 4130 steel ({approx}300 C). The tempering temperatures for the precipitation of transition carbides and cementite were significantly higher (>400 C) than for carbon steels (100 C to 200 C and 200 C to 350 C), respectively. Approximately 90 pct of the carbon atoms were trapped in Cottrell atmospheres in the vicinity of the dislocation cores in dislocation tangles in the martensite matrix after cooling at 560 K/s and aging at 22 C. The 3.2 at. pct Si content increased the upper temperature limit for stable carbon clusters to above 215 C. Significant autotempering occurred during cooling at 25 K/s. The proportion of total carbon that segregated to the interlath austenite films decreased from 34 to 8 pct as the cooling rate increased from 25 to 560 K/s. Developing a model for the transfer of carbon from martensite to austenite during quenching should provide a means for calculating the retained austenite. The maximum carbon content in the austenite films was 6 to 7 at. pct, both in specimens cooled at 560 K/s and at 25 K/s. Approximately 6 to 7 at. pct carbon was sufficient to arrest the transformation of austenite to martensite. The chemical potential of carbon is the same in martensite

  16. Characterization of the Carbon and Retained Austenite Distributions in Martensitic Medium Carbon, High Silicon Steel

    NASA Astrophysics Data System (ADS)

    Sherman, Donald H.; Cross, Steven M.; Kim, Sangho; Grandjean, Fernande; Long, Gary J.; Miller, Michael K.

    2007-08-01

    The retained austenite content and carbon distribution in martensite were determined as a function of cooling rate and temper temperature in steel that contained 1.31 at. pct C, 3.2 at. pct Si, and 3.2 at. pct noniron metallic elements. Mössbauer spectroscopy, transmission electron microscopy (TEM), transmission synchrotron X-ray diffraction (XRD), and atom probe tomography were used for the microstructural analyses. The retained austenite content was an inverse, linear function of cooling rate between 25 and 560 K/s. The elevated Si content of 3.2 at. pct did not shift the start of austenite decomposition to higher tempering temperatures relative to SAE 4130 steel. The minimum tempering temperature for complete austenite decomposition was significantly higher (>650 °C) than for SAE 4130 steel (˜300 °C). The tempering temperatures for the precipitation of transition carbides and cementite were significantly higher (>400 °C) than for carbon steels (100 °C to 200 °C and 200 °C to 350 °C), respectively. Approximately 90 pct of the carbon atoms were trapped in Cottrell atmospheres in the vicinity of the dislocation cores in dislocation tangles in the martensite matrix after cooling at 560 K/s and aging at 22 °C. The 3.2 at. pct Si content increased the upper temperature limit for stable carbon clusters to above 215 °C. Significant autotempering occurred during cooling at 25 K/s. The proportion of total carbon that segregated to the interlath austenite films decreased from 34 to 8 pct as the cooling rate increased from 25 to 560 K/s. Developing a model for the transfer of carbon from martensite to austenite during quenching should provide a means for calculating the retained austenite. The maximum carbon content in the austenite films was 6 to 7 at. pct, both in specimens cooled at 560 K/s and at 25 K/s. Approximately 6 to 7 at. pct carbon was sufficient to arrest the transformation of austenite to martensite. The chemical potential of carbon is the same in

  17. 78 FR 59652 - Certain Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Notice of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-27

    ... International Trade Administration Certain Corrosion-Resistant Carbon Steel Flat Products From the Republic of... administrative review of the antidumping duty order on certain corrosion-resistant carbon steel flat products... Results. \\2\\ See Certain Corrosion-Resistant Carbon Steel Flat Products from the Republic of Korea:...

  18. 78 FR 16247 - Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea; Final Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-14

    ... International Trade Administration Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea... antidumping duty order on corrosion-resistant carbon steel flat products (CORE) from the Republic of Korea... section entitled ``Final Results of Review.'' \\1\\ See Certain Corrosion-Resistant Carbon Steel...

  19. 76 FR 77775 - Corrosion-Resistant Carbon Steel Flat Products from the Republic of Korea: Extension of Time...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-14

    ... International Trade Administration Corrosion-Resistant Carbon Steel Flat Products from the Republic of Korea... countervailing duty order on corrosion-resistant carbon steel flat products from the Republic of Korea covering the period January 1, 2009, through December 31, 2009. See Corrosion-Resistant Carbon Steel...

  20. 77 FR 24221 - Corrosion-Resistant Carbon Steel Flat Products From Germany and Korea; Notice of Commission...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-23

    ... COMMISSION Corrosion-Resistant Carbon Steel Flat Products From Germany and Korea; Notice of Commission... countervailing duty order on corrosion-resistant carbon steel flat products from Korea and the antidumping duty orders on corrosion- resistant carbon steel flat products from Germany and Korea would be likely to...

  1. 77 FR 13093 - Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Final Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-05

    ... International Trade Administration Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea... administrative review of the countervailing duty (``CVD'') order on corrosion-resistant carbon steel flat... Review'' below. \\1\\ See Corrosion-Resistant Carbon Steel Flat Products from the Republic of...

  2. 78 FR 59651 - Certain Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Notice of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-27

    ... International Trade Administration Certain Corrosion-Resistant Carbon Steel Flat Products From the Republic of... fourteenth administrative review of the antidumping duty order on certain corrosion-resistant carbon steel... aspects of the Final Results. \\2\\ See Certain Corrosion-Resistant Carbon Steel Flat Products from...

  3. 77 FR 31877 - Corrosion-Resistant Carbon Steel Flat Products From Germany and Korea; Scheduling of Full Five...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-05-30

    ... COMMISSION Corrosion-Resistant Carbon Steel Flat Products From Germany and Korea; Scheduling of Full Five... duty order on corrosion-resistant carbon steel flat products from Korea and the antidumping duty orders on corrosion- resistant carbon steel flat products from Germany and Korea would be likely to lead...

  4. 78 FR 16832 - Corrosion-Resistant Carbon Steel Flat Products From Germany and the Republic of Korea: Revocation...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-19

    ... International Trade Administration Corrosion-Resistant Carbon Steel Flat Products From Germany and the Republic... corrosion-resistant carbon steel flat products (``CORE'') from Germany and the Republic of Korea (``Korea...-Year (``Sunset'') Review, 77 FR 85 (January 3, 2012). \\2\\ See Corrosion-Resistant Carbon Steel...

  5. 76 FR 63902 - Circular Welded Carbon Steel Pipes and Tubes From Taiwan: Final Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-14

    ... International Trade Administration Circular Welded Carbon Steel Pipes and Tubes From Taiwan: Final Results of... preliminary results of the administrative review of the antidumping duty order on circular welded carbon steel... Welded Carbon Steel Pipes and Tubes From Taiwan, 76 FR 33210 (June 8, 2011) (Preliminary Results)....

  6. 75 FR 67108 - Cut-To-Length Carbon Steel Plate From India, Indonesia, Italy, Japan, and Korea

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-01

    ... COMMISSION Cut-To-Length Carbon Steel Plate From India, Indonesia, Italy, Japan, and Korea AGENCY: United... and the antidumping duty orders on CTL carbon steel plate from India, Indonesia, Italy, Japan, and... duty orders on CTL carbon steel plate from India, Indonesia, Italy, Japan, and Korea would be likely to...

  7. 75 FR 60814 - Carbon Steel Butt-Weld Pipe Fittings From Brazil, China, Japan, Taiwan, and Thailand

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-01

    ... COMMISSION Carbon Steel Butt-Weld Pipe Fittings From Brazil, China, Japan, Taiwan, and Thailand AGENCY... antidumping duty orders on carbon steel butt-weld pipe fittings from Brazil, China, Japan, Taiwan, and... antidumping duty orders on carbon steel butt-weld pipe fittings from Brazil, China, Japan, Taiwan, and...

  8. 77 FR 5240 - Light-Walled Welded Rectangular Carbon Steel Tubing From Taiwan: Continuation of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-02

    ... International Trade Administration Light-Walled Welded Rectangular Carbon Steel Tubing From Taiwan: Continuation... light-walled welded rectangular carbon steel tubing from Taiwan would likely lead to a continuation or... sunset review of the antidumping duty order \\1\\ on light-walled welded rectangular carbon steel...

  9. 75 FR 69626 - Certain Welded Carbon Steel Standard Pipes and Tubes From India: Final Results of Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-15

    ... Welded Carbon Steel Standard Pipes and Tubes From India: Final Results of Antidumping Duty Administrative... review of the antidumping duty order on certain welded carbon steel standard pipes and tubes from India... duty order on certain welded carbon steel standard pipes and tubes from India. See Certain...

  10. 75 FR 70723 - Circular Welded Carbon Steel Pipes and Tubes From Taiwan: Notice of Partial Rescission of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-18

    ... International Trade Administration Circular Welded Carbon Steel Pipes and Tubes From Taiwan: Notice of Partial... circular welded carbon steel pipes and tubes from Taiwan. The review covers two firms: Yieh Phui Enterprise... the antidumping duty order on circular welded carbon steel pipes and tubes from Taiwan covering...

  11. 76 FR 77480 - Certain Circular Welded Carbon Steel Pipes and Tubes From Taiwan: Notice of Rescission of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-13

    ... International Trade Administration Certain Circular Welded Carbon Steel Pipes and Tubes From Taiwan: Notice of... of the antidumping duty order on circular welded carbon steel pipes and tubes from Taiwan. The period... the antidumping duty order on circular welded carbon steel pipes and tubes from Taiwan covering...

  12. 78 FR 65272 - Circular Welded Carbon Steel Pipes and Tubes From Thailand: Final Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-31

    ... International Trade Administration Circular Welded Carbon Steel Pipes and Tubes From Thailand: Final Results of... antidumping duty order on circular welded carbon steel pipes and tubes from Thailand. This review covers two... carbon steel pipes and tubes from Thailand.\\1\\ We invited interested parties to comment on...

  13. 76 FR 78886 - Certain Welded Carbon Steel Standard Pipe and Tube From Turkey: Intent To Rescind Countervailing...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-20

    ... International Trade Administration Certain Welded Carbon Steel Standard Pipe and Tube From Turkey: Intent To... the countervailing duty (CVD) order on certain welded carbon steel pipe and tube from Turkey. See... products covered by this order are certain welded carbon steel pipe and tube with an outside diameter of...

  14. 77 FR 6542 - Certain Welded Carbon Steel Standard Pipe and Tube From Turkey: Notice of Final Rescission of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-08

    ... International Trade Administration Certain Welded Carbon Steel Standard Pipe and Tube From Turkey: Notice of... of the countervailing duty (CVD) order on certain welded carbon steel pipe and tube from Turkey for... the preliminary decision. See Certain Welded Carbon Steel Standard Pipe and Tube from Turkey:...

  15. 75 FR 28557 - Circular Welded Carbon Steel Pipes and Tubes From Thailand: Extension of Time Limit for Final...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-21

    ... International Trade Administration Circular Welded Carbon Steel Pipes and Tubes From Thailand: Extension of Time... antidumping duty order on circular welded carbon steel pipes and tubes from Thailand. See Circular Welded Carbon Steel Pipes and Tubes from Thailand: Preliminary Results and Rescission, in Part, of...

  16. 75 FR 4529 - Circular Welded Carbon Steel Pipes and Tubes From Thailand: Final Results of Antidumping Duty New...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-28

    ... International Trade Administration Circular Welded Carbon Steel Pipes and Tubes From Thailand: Final Results of... circular welded carbon steel pipes and tubes (pipes and tubes) from Thailand. See Circular Welded Carbon Steel Pipes and Tubes from Thailand: Preliminary Results of Antidumping Duty New Shipper Review, 74...

  17. 77 FR 72818 - Circular Welded Carbon Steel Pipes and Tubes From Turkey; Final Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-06

    ... International Trade Administration Circular Welded Carbon Steel Pipes and Tubes From Turkey; Final Results of... circular welded carbon steel pipes and tubes from Turkey.\\1\\ This review covers four producers and... section entitled ``Final Results of Review.'' \\1\\ See Circular Welded Carbon Steel Pipes and Tubes...

  18. 75 FR 62366 - Circular Welded Carbon Steel Pipes and Tubes From Taiwan: Final Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-08

    ... Welded Carbon Steel Pipes and Tubes From Taiwan: Final Results of Antidumping Duty Administrative Review... administrative review of the antidumping duty order on circular welded carbon steel pipes and tubes from Taiwan. See Preliminary Results of Antidumping Duty Administrative Review: Circular Welded Carbon Steel...

  19. 77 FR 64473 - Circular Welded Carbon-Quality Steel Pipe From the Sultanate of Oman: Final Affirmative...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-22

    ... International Trade Administration Circular Welded Carbon-Quality Steel Pipe From the Sultanate of Oman: Final... countervailable subsidies are being provided to producers and exporters of circular welded carbon-quality steel... Welded Carbon-Quality Steel Pipe from the Sultanate of Oman: Preliminary Negative Countervailing...

  20. 77 FR 64465 - Circular Welded Carbon-Quality Steel Pipe From the United Arab Emirates: Final Affirmative...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-22

    ... International Trade Administration Circular Welded Carbon-Quality Steel Pipe From the United Arab Emirates... countervailable subsidies are being provided to producers and exporters of circular welded carbon-quality steel...\\ \\1\\ See Circular Welded Carbon-Quality Steel Pipe From the United Arab Emirates: Preliminary...

  1. 76 FR 78313 - Circular Welded Carbon-Quality Steel Pipe From India, Oman, the United Arab Emirates, and Vietnam

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-16

    ... COMMISSION Circular Welded Carbon-Quality Steel Pipe From India, Oman, the United Arab Emirates, and Vietnam... United Arab Emirates, and Vietnam of circular welded carbon- quality steel pipe, provided for in... material injury by reason of LTFV and subsidized imports of circular welded carbon-quality steel pipe...

  2. 75 FR 68327 - Certain Welded Carbon Steel Standard Pipes and Tubes From India: Rescission of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-05

    ... International Trade Administration Certain Welded Carbon Steel Standard Pipes and Tubes From India: Rescission... certain welded carbon steel standard pipes and tubes from India. The period of review is May 1, 2009... initiation of an administrative review of the antidumping duty order on certain welded carbon steel...

  3. 76 FR 66901 - Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of China: Final...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-28

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of... duty order on certain hot-rolled carbon steel flat products (``hot-rolled'') from the People's Republic... Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of China: Preliminary Intent To...

  4. 75 FR 27297 - Certain Hot-Rolled Carbon Steel Flat Products from India: Notice of Final Results of Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-14

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products from India: Notice of Final... antidumping duty administrative review for certain hot-rolled carbon steel flat products from India (``Indian Hot-Rolled''). See Certain Hot-Rolled Carbon Steel Flat Products from India: Notice of Preliminary...

  5. 77 FR 54891 - Certain Corrosion-Resistant Carbon Steel Flat Products from the Republic of Korea: Preliminary...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-06

    ... International Trade Administration Certain Corrosion-Resistant Carbon Steel Flat Products from the Republic of... administrative review of the antidumping order on corrosion-resistant carbon steel flat products (CORE) from the... the order on March 12, 2012. See Certain Corrosion- Resistant Carbon Steel Flat Products From the...

  6. 78 FR 55057 - Corrosion-Resistant Carbon Steel Flat Products from the Republic of Korea: Preliminary Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-09

    ... International Trade Administration Corrosion-Resistant Carbon Steel Flat Products from the Republic of Korea... antidumping duty order on corrosion-resistant carbon steel flat products (CORE) from the Republic of Korea.... See Corrosion-Resistant Carbon Steel Flat Products from Germany and the Republic of Korea: Revocation...

  7. 77 FR 72827 - Corrosion-Resistant Carbon Steel Flat Products From Germany and the Republic of Korea: Final...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-06

    ... International Trade Administration Corrosion-Resistant Carbon Steel Flat Products From Germany and the Republic... on certain corrosion- resistant carbon steel flat products (``CORE'') from Germany and the Republic... Reviews'' section of this notice. \\1\\ Corrosion-Resistant Carbon Steel Flat Products From Germany and the...

  8. 77 FR 14501 - Certain Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Notice of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-12

    ... International Trade Administration Certain Corrosion-Resistant Carbon Steel Flat Products From the Republic of... antidumping duty administrative review for certain corrosion-resistant carbon steel flat products (CORE) from... (POR) is August 1, 2009, through, July 31, 2010. \\1\\ See Certain Corrosion-Resistant Carbon Steel Flat...

  9. 75 FR 55769 - Certain Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Notice of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-14

    ... International Trade Administration Certain Corrosion-Resistant Carbon Steel Flat Products From the Republic of... administrative review of the antidumping order on corrosion-resistant carbon steel flat products (CORE) from the... Antidumping Duty Orders on Certain Cold-Rolled Carbon Steel Flat Products and Certain Corrosion-Resistant...

  10. 76 FR 15291 - Certain Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Notice of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-21

    ... International Trade Administration Certain Corrosion-Resistant Carbon Steel Flat Products From the Republic of... for certain corrosion-resistant carbon steel flat products (CORE) from the Republic of Korea (Korea). See Certain Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Notice of...

  11. 76 FR 22868 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil: Final Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-25

    ... International Trade Administration Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil... certain hot-rolled flat-rolled carbon- quality steel products (HRS) from Brazil for the period January 1...: Background Since the issuance of Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil...

  12. 75 FR 47263 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From the Russian Federation; Final...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-08-05

    ... International Trade Administration Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From the Russian... carbon- quality steel products from the Russian Federation; final results. SUMMARY: On April 1, 2010, the... antidumping duty investigation of certain hot-rolled flat- rolled carbon-quality steel products (``hot-rolled...

  13. 76 FR 24462 - Certain Cut-to-Length Carbon Steel Plate From the People's Republic of China: Rescission of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-02

    ... International Trade Administration Certain Cut-to-Length Carbon Steel Plate From the People's Republic of China... antidumping duty order on certain cut-to-length carbon steel plate (``CTL Plate'') from the People's Republic of China (``PRC''). See Suspension Agreement on Certain Cut- to-Length Carbon Steel Plate From...

  14. 75 FR 29519 - Certain Cut-to-Length Carbon Steel Plate from the People's Republic of China: Rescission of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-26

    ... Cut-to-Length Carbon Steel Plate from the People's Republic of China: Rescission of Antidumping Duty... certain cut-to-length carbon steel plate (``CTL Plate'') from the People's Republic of China (``PRC''). See Suspension Agreement on Certain Cut- to-Length Carbon Steel Plate From the People's Republic...

  15. 75 FR 29976 - Certain Cut-to-Length Carbon-Quality Steel Plate Products From Italy: Extension of the Final...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-28

    ... International Trade Administration Certain Cut-to-Length Carbon-Quality Steel Plate Products From Italy... antidumping duty order on certain cut-to-length carbon-quality steel plate products from Italy. See Certain Cut-to-Length Carbon-Quality Steel Plate Products From Italy: Preliminary Results of Antidumping...

  16. 78 FR 44525 - Certain Cut-to-Length Carbon Steel Plate From the People's Republic of China: Preliminary Results...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-24

    ... International Trade Administration Certain Cut-to-Length Carbon Steel Plate From the People's Republic of China... on certain cut-to- length carbon steel plate (``CTL plate'') from the People's Republic of China... certain cut-to-length carbon steel plate from the PRC.\\2\\ This merchandise is currently classified in the...

  17. 75 FR 13255 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe from the People's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-19

    ... International Trade Administration Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe... determination in this countervailing duty investigation of certain seamless carbon and alloy steel standard... of seamless pipe from the PRC. See Certain Seamless Carbon and Alloy Steel Standard, Line,...

  18. 75 FR 29972 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe from the People's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-28

    ... International Trade Administration Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe... antidumping duty investigation of certain seamless carbon and alloy steel standard, line, and pressure pipe... in this proceeding. See Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure...

  19. 78 FR 28190 - Carbon and Certain Alloy Steel Wire Rod From Mexico: Final Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-14

    ... International Trade Administration Carbon and Certain Alloy Steel Wire Rod From Mexico: Final Results of... carbon and certain alloy steel wire rod (wire rod) from Mexico. The period of review (POR) is October 1... (the Act). \\1\\ See Carbon and Certain Alloy Steel Wire Rod From Mexico: Preliminary Results...

  20. 75 FR 69050 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the People's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-10

    ... International Trade Administration Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe... duty order on certain seamless carbon and alloy steel standard, line, and pressure pipe (``seamless... seamless pipe from the PRC. See Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure...

  1. 75 FR 6183 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe from the People's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-02-08

    ... INTERNATIONAL TRADE ADMINISTRATION (A-570-956) Certain Seamless Carbon and Alloy Steel Standard, Line, and... investigation on certain seamless carbon and alloy steel standard, line, and pressure pipe from the People's Republic of China. See Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From...

  2. 75 FR 59689 - Certain Hot-Rolled Carbon Steel Flat Products From India: Notice of Court Decision Not in Harmony...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-28

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From India: Notice of Court... administrative review of the countervailing duty order on certain hot-rolled carbon steel flat products (HRCS... Certain Hot-Rolled Carbon Steel Flat Products from India: Final Results of Countervailing...

  3. 77 FR 25404 - Certain Hot-Rolled Carbon Steel Flat Products From India: Rescission of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-30

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From India: Rescission of... request an administrative review of the antidumping duty order on certain hot- rolled carbon steel flat..., through Melissa Skinner, Office Director, concerning ``Certain Hot Rolled Carbon Steel Flat Products...

  4. 75 FR 43488 - Certain Hot-Rolled Carbon Steel Flat Products From India: Final Results of Countervailing Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-26

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From India: Final Results of... duty (CVD) order on certain hot-rolled carbon steel flat products (hot-rolled carbon steel) from India for the period of review (POR) January 1, 2008, through December 31, 2008. See Certain...

  5. 75 FR 18152 - Certain Hot-Rolled Carbon Steel Flat Products from India: Extension of Time Limit for Final...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-09

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products from India: Extension of Time... countervailing duty order on certain hot- rolled carbon steel flat products from India covering the period January 1, 2008, through December 31, 2008. See Certain Hot-Rolled Carbon Steel Flat Products From...

  6. 76 FR 65497 - Certain Hot-Rolled Carbon Steel Flat Products From India: Amended Final Results of Countervailing...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-21

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From India: Amended Final... of the countervailing duty order on certain hot-rolled carbon steel flat products (HRCS) from India..., to reflect the CIT's decision in Essar. See Certain Hot-Rolled Carbon Steel Flat Products from...

  7. 76 FR 66893 - Certain Circular Welded Carbon Steel Pipes and Tubes From India, Thailand, and Turkey; Final...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-28

    ... International Trade Administration Certain Circular Welded Carbon Steel Pipes and Tubes From India, Thailand... antidumping duty orders on certain circular welded carbon steel pipes and tubes from India, Thailand, and... India, Thailand, and Turkey. See Antidumping Duty Order; Certain Welded Carbon Steel Standard Pipes...

  8. 75 FR 33262 - Certain Welded Carbon Steel Pipe and Tube from Turkey: Notice of Preliminary Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-11

    ... International Trade Administration Certain Welded Carbon Steel Pipe and Tube from Turkey: Notice of Preliminary... order on certain welded carbon steel pipe and tube (``welded pipe and tube'') from Turkey. See... tube from Turkey. See Antidumping Duty Order; Welded Carbon Steel Standard Pipe and Tube Products From...

  9. The role of hydrogen in carbonate stress corrosion cracking of low-carbon steel

    NASA Astrophysics Data System (ADS)

    Hirnyj, Sviatoslav

    Hydrogen generation and ingress into low carbon steel has been discovered at high anodic potentials of high-pH stress corrosion cracking in the so-called "standard" carbonate-bicarbonate solution. The experimental study showed that hydrogen absorption occurs over the whole range of anodic potentials which cause transgranular stress corrosion cracking and coincides with formation of iron (II) carbonate. Also, hydrogen ingress into steel was measured at the lowest part of the range of potentials where most severe intergranular stress corrosion cracking takes place and where the passive film is a composite of siderite and magnetite. Hydrogen absorption occurs at least 170 mV above the so-called line (a) on the Pourbaix diagram and thus it is not governed by known cathodic reactions but by another process. An adsorption based model for anodic hydrogenation in bicarbonate solution has been proposed. Other experimental findings and theoretical calculations in relation to high pH stress corrosion cracking of low carbon steel are presented.

  10. Gas tungsten arc and shielded metal arc welding of carbon steel to chromium-nickel steel. Welding procedure specification

    SciTech Connect

    Wodtke, C.H.; Frizzell, D.R.; Plunkett, W.A.

    1985-08-01

    Procedure WPS-2103-ASME-1 is qualified under Section IX of the ASME Boiler and Pressure Vessel Code for gas tungsten arc and shielded metal arc welding of carbon steels (P-1-1) to 300 series Cr-Ni steels (P-8-1), in thickness range 0.25 to 2 in.; filler metals are ERNiCr-3 (F-43) (GTAW) and ENiCrFe-3 (F-43) (SMAW); shielding gas is argon (GTAW).

  11. Effects of Carbon and Nitrogen on the Microstructure and Mechanical Properties of Carbonitrided Low-Carbon Steel

    NASA Astrophysics Data System (ADS)

    Taweejun, Nipon; Kanchanomai, Chaosuan

    2015-12-01

    Various carbonitriding processes have been applied to low-carbon steel. The carbon and nitrogen contents in the case of carbonitrided low-carbon steels have been evaluated, and their influences on microstructure, distortion, hardness, and strength have been investigated. The factor limiting the ferrite and pearlite formations with increasing nitrogen content was a mechanism that resulted in more retained austenite in the case of low-carbon steel treated using a high flow rate of ammonia. The high-nitrogen content and high amount of retained austenite in the case of carbonitrided low-carbon steel slightly reduced the hardness, case depth, and strength. However, the elongation was improved, and the distortion was reduced. In the case zones, fractures occurred along the grain boundaries, i.e., intergranular fractures, whereas the fracture surfaces in the core regions were typical ductile fractures, i.e., dimples were observed.

  12. Environmental review of options for managing radioactively contaminated carbon steel

    SciTech Connect

    1996-10-01

    The U.S. Department of Energy (DOE) is proposing to develop a strategy for the management of radioactively contaminated carbon steel (RCCS). Currently, most of this material either is placed in special containers and disposed of by shallow land burial in facilities designed for low-level radioactive waste (LLW) or is stored indefinitely pending sufficient funding to support alternative disposition. The growing amount of RCCS with which DOE will have to deal in the foreseeable future, coupled with the continued need to protect the human and natural environment, has led the Department to evaluate other approaches for managing this material. This environmental review (ER) describes the options that could be used for RCCS management and examines the potential environmental consequences of implementing each. Because much of the analysis underlying this document is available from previous studies, wherever possible the ER relies on incorporating the conclusions of those studies as summaries or by reference.

  13. Electric arc surfacing on low carbon steel: Structure and properties

    NASA Astrophysics Data System (ADS)

    Ivanov, Yurii; Gromov, Victor; Kormyshev, Vasilii; Konovalov, Sergey; Kapralov, Evgenii; Semin, Alexander

    2016-11-01

    By the methods of modern materials science, the structure-phase state and microhardness distribution along the cross-section of single and double coatings surfaced on martensite low carbon steel by alloy powder-cored wire were studied. It was established that the increased mechanical properties of surfaced layer are determined by the sub-micro and nanodispersed martensite structure formation, containing iron borides forming the eutectic of lamellar form. The plates of Fe2B are formed mainly in the eutectic of a single-surfaced layer, while FeB is formed in a double-surfaced layer. The existence of bend extinction contours indicating the internal stress fields formation at the boundaries of Fe borides-α-Fe phases were revealed.

  14. Effects of water temperature on cracking of wet-welded carbon steel

    SciTech Connect

    West, T.C.; Mitchell, W.E.; Murray, R.I.

    1996-10-01

    Industry generally accepts that carbon steel shielded metal arc welding electrodes can be used to wet-weld carbon steel base metals without incurring hydrogen-induced underbead cracking, as long as the carbon equivalent of the base metal is approximately 0.40 or less. At higher carbon equivalents, austenitic wet welding electrodes can be used to avoid such cracking. ANSI/AWS D3.6-93, Specification for Underwater Welding, lists both the carbon equivalent and carbon content as essential variables during wet welding procedure qualification. Since variations in water temperature might seem insignificant compared to typical electric welding arc temperatures, the specification omits water temperature as an essential variable during wet welding procedure qualification. However, recent welding procedure qualification testing, and follow-on evaluations, have shown that the water temperature does contribute to base metal cracking, if the carbon equivalent of the carbon steel (ASTM A516 Gr.70) base metal approaches 0.40.

  15. Energy use and carbon dioxide emissions in the steel sector in key developing countries

    SciTech Connect

    Price, L.K.; Phylipsen, G.J.M.; Worrell, E.

    2001-04-01

    Iron and steel production consumes enormous quantities of energy, especially in developing countries where outdated, inefficient technologies are still used to produce iron and steel. Carbon dioxide emissions from steel production, which range between 5 and 15% of total country emissions in key developing countries (Brazil, China, India, Mexico, and South Africa), will continue to grow as these countries develop and as demand for steel products such as materials, automobiles, and appliances increases. In this report, we describe the key steel processes, discuss typical energy-intensity values for these processes, review historical trends in iron and steel production by process in five key developing countries, describe the steel industry in each of the five key developing countries, present international comparisons of energy use and carbon dioxide emissions among these countries, and provide our assessment of the technical potential to reduce these emissions based on best-practice benchmarking. Using a best practice benchmark, we find that significant savings, in the range of 33% to 49% of total primary energy used to produce steel, are technically possible in these countries. Similarly, we find that the technical potential for reducing intensities of carbon dioxide emissions ranges between 26% and 49% of total carbon dioxide emissions from steel production in these countries.

  16. Steel slag carbonation in a flow-through reactor system: the role of fluid-flux.

    PubMed

    Berryman, Eleanor J; Williams-Jones, Anthony E; Migdisov, Artashes A

    2015-01-01

    Steel production is currently the largest industrial source of atmospheric CO2. As annual steel production continues to grow, the need for effective methods of reducing its carbon footprint increases correspondingly. The carbonation of the calcium-bearing phases in steel slag generated during basic oxygen furnace (BOF) steel production, in particular its major constituent, larnite {Ca2SiO4}, which is a structural analogue of olivine {(MgFe)2SiO4}, the main mineral subjected to natural carbonation in peridotites, offers the potential to offset some of these emissions. However, the controls on the nature and efficiency of steel slag carbonation are yet to be completely understood. Experiments were conducted exposing steel slag grains to a CO2-H2O mixture in both batch and flow-through reactors to investigate the impact of temperature, fluid flux, and reaction gradient on the dissolution and carbonation of steel slag. The results of these experiments show that dissolution and carbonation of BOF steel slag are more efficient in a flow-through reactor than in the batch reactors used in most previous studies. Moreover, they show that fluid flux needs to be optimized in addition to grain size, pressure, and temperature, in order to maximize the efficiency of carbonation. Based on these results, a two-stage reactor consisting of a high and a low fluid-flux chamber is proposed for CO2 sequestration by steel slag carbonation, allowing dissolution of the slag and precipitation of calcium carbonate to occur within a single flow-through system.

  17. Effect of Stress Relief Annealing on Microstructure & Mechanical Properties of Welded Joints Between Low Alloy Carbon Steel and Stainless Steel

    NASA Astrophysics Data System (ADS)

    Nivas, R.; Das, G.; Das, S. K.; Mahato, B.; Kumar, S.; Sivaprasad, K.; Singh, P. K.; Ghosh, M.

    2017-01-01

    Two types of welded joints were prepared using low alloy carbon steel and austenitic stainless steel as base materials. In one variety, buttering material and weld metal were Inconel 82. In another type, buttering material and weld metal were Inconel 182. In case of Inconel 82, method of welding was GTAW. For Inconel 182, welding was done by SMAW technique. For one set of each joints after buttering, stress relief annealing was done at 923 K (650 °C) for 90 minutes before further joining with weld metal. Microstructural investigation and sub-size in situ tensile testing in scanning electron microscope were carried out for buttered-welded and buttered-stress relieved-welded specimens. Adjacent to fusion boundary, heat-affected zone of low alloy steel consisted of ferrite-pearlite phase combination. Immediately after fusion boundary in low alloy steel side, there was increase in matrix grain size. Same trend was observed in the region of austenitic stainless steel that was close to fusion boundary between weld metal-stainless steel. Close to interface between low alloy steel-buttering material, the region contained martensite, Type-I boundary and Type-II boundary. Peak hardness was obtained close to fusion boundary between low alloy steel and buttering material. In this respect, a minimum hardness was observed within buttering material. The peak hardness was shifted toward buttering material after stress relief annealing. During tensile testing no deformation occurred within low alloy steel and failure was completely through buttering material. Crack initiated near fusion boundary between low alloy steel-buttering material for welded specimens and the same shifted away from fusion boundary for stress relieved annealed specimens. This observation was at par with the characteristics of microhardness profile. In as welded condition, joints fabricated with Inconel 82 exhibited superior bond strength than the weld produced with Inconel 182. Stress relief annealing

  18. Inhibitive effects of palm kernel oil on carbon steel corrosion by alkaline solution

    NASA Astrophysics Data System (ADS)

    Zulkafli, M. Y.; Othman, N. K.; Lazim, A. M.; Jalar, A.

    2013-11-01

    The behavior of carbon steel SAE 1045 in 1 M NaOH solution containing different concentrations of palm kernel oil (PKO) has been studied by weight loss and polarization measurement. Results showed that the corrosion of carbon steel in NaOH solution was considerably reduced in presence of such inhibitors. The inhibition efficiency increases when concentration of inhibitor increase. Maximum inhibition efficiency (≈ 96.67%) is obtained at PKO concentration 8 v/v %. This result revealed that palm kernel oil can act as a corrosion inhibitor in an alkaline medium. Corrosion rates of carbon steel decrease as the concentration of inhibitor is increased.

  19. Analysis of the Parameters Influencing the Quench-Aging Behavior of Ultra-Low-Carbon Steels

    NASA Astrophysics Data System (ADS)

    Massardier, V.; Merlin, J.

    2009-05-01

    The influence of the annealing temperature and of the grain size on the quench-aging behavior of ultra-low-carbon (ULC) steels was investigated by thermoelectric power measurements (TEPs) and mechanical testing. The TEP technique showed that the quench aging of ULC steels occurs in two distinct stages: (1) the segregation of carbon atoms to the grain boundaries and (2) the precipitation of iron carbides. It was suggested that the degree of grain boundary coverage by the carbon atoms resulting from the annealing or aging conditions influences the development of the yield point of ULC steels.

  20. Local hardening evaluation of carbon steels by using frequency sweeping excitation and spectrogram method

    NASA Astrophysics Data System (ADS)

    Tsuchida, Yuji; Kudo, Yuki; Enokizono, Masato

    2017-02-01

    This paper presents our proposed frequency sweeping excitation and spectrogram method (FSES method) by a magnetic sensor for non-destructive testing of hardened low carbon steels. This method can evaluate the magnetic properties of low carbon steels which were changed after induction heating treatment. It was examined by our proposed method that the degrees of yield strength of low carbon steels were varied depending on hardened conditions. Moreover, it was made clear that the maximum magnetic field strength, Hmax, derived from the measured B-H loops was very sensitive to the hardening if the surface of the samples were flat.

  1. 75 FR 62566 - Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-12

    ... COMMISSION Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia AGENCY: United... Brazil, the antidumping duty orders on hot-rolled steel from Brazil and Japan, and the suspended... steel from Brazil, the antidumping duty orders on hot-rolled steel from Brazil and Japan, and/ or the...

  2. 77 FR 263 - Certain Cut-To-Length Carbon-Quality Steel Plate From Italy and Japan: Revocation of Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-04

    ...) abrasion-resistant steels (i.e., USS AR 400, USS AR 500); (5) products made to ASTM A202, A225, A514 grade S, A517 grade S, or their proprietary equivalents; (6) ball bearing steels; (7) tool steels; and (8... International Trade Administration Certain Cut-To-Length Carbon-Quality Steel Plate From Italy and...

  3. Stress state evaluation in low carbon and TRIP steels by magnetic permeability

    NASA Astrophysics Data System (ADS)

    Kouli, M.-E.; Giannakis, M.

    2016-03-01

    Magnetic permeability is an indicative factor for the steel health monitoring. The measurements of magnetic permeability lead to the evaluation of the stress state of any ferromagnetic steel. The magnetic permeability measurements were conducted on low carbon and TRIP steel samples, which were subjected to both tensile and compressive stresses. The results indicated a direct correlation of the magnetic permeability with the mechanical properties, the stress state and the microstructural features of the examined samples.

  4. Surface Modification of Commercial Low-Carbon Steel using Glow Discharge Nitrogen Plasma and its Characterization

    NASA Astrophysics Data System (ADS)

    Srikanth, S.; Saravanan, P.; Joseph, Alphonsa; Ravi, K.

    2013-09-01

    Plasma nitriding under glow discharge nitrogen plasma has been undertaken on laboratory scale for surface engineering of commercial low carbon steels. The treatment has been shown to confer exceptional improvement in surface properties, viz., hardness and corrosion resistance. The results have been discussed in light of microstructural changes occurring on steel surface and its interior as a result of Fickian nitrogen diffusion and correlated with influences of nitriding-temperature and alloying elements (Mn, Nb, and Si) in steel.

  5. Fatigue of carbon and low-alloy steels in LWR environments

    SciTech Connect

    Chopra, O.K.; Michaud, W.F.; Shack, W.J.

    1993-10-01

    Fatigue tests have been conducted on A106-Gr B carbon steel and A533-Gr B low-alloy steel to evaluate the effects of an oxygenated-water environment on the fatigue life of these steels. For both steels, environmental effects are modest in PWR water at all strain rates. Fatigue data in oxygenated water confirm the strong dependence of fatigue life on dissolved oxygen (DO) and strain rate. The effect of strain rate on fatigue life saturates at some low value, e.g., between 0.0004 and 0.001%/s in oxygenated water with {approximately}0.8 ppm DO. The data suggest that the saturation value of strain rate may vary with DO and sulfur content of the steel. Although the cyclic stress-strain and cyclic-hardening behavior of carbon and low-alloy steels is distinctly different, the degradation of fatigue life of these two steels with comparable sulfur levels is similar. The carbon steel exhibits pronounced dynamic strain aging, whereas strain-aging effects are modest in the low-alloy steel. Environmental effects on nucleation of fatigue crack have also been investigated. The results suggest that the high-temperature oxygenated water has little or no effect on crack nucleation.

  6. 77 FR 61738 - Circular Welded Carbon Steel Pipes and Tubes From Thailand: Final Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-11

    ... International Trade Administration Circular Welded Carbon Steel Pipes and Tubes From Thailand: Final Results of... preliminary results of administrative review of the antidumping duty order on circular welded carbon steel... (Pacific Pipe) and Saha Thai Steel Pipe (Public) Company, Ltd. (Saha Thai). Based on our analysis of...

  7. 77 FR 73674 - Circular Welded Carbon-Quality Steel Pipe From India, Oman, The United Arab Emirates, and Vietnam

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-11

    ...-1191-1194 (Final)] Circular Welded Carbon-Quality Steel Pipe From India, Oman, The United Arab Emirates... of circular welded carbon-quality steel pipe from India, Oman, the United Arab Emirates, and Vietnam... and Conduit, Harvey, IL; JMC Steel Group, Chicago, IL; Wheatland Tube, Sharon, PA; and United...

  8. 76 FR 34101 - Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-10

    ... COMMISSION Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia Determinations... steel products from Brazil and Japan would not be likely to lead to continuation or recurrence of...-rolled flat-rolled carbon-quality steel products from Brazil and Japan. Background The Commission...

  9. 75 FR 73033 - Circular Welded Carbon Steel Pipes and Tubes from Thailand: Amended Final Results of Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-29

    ... International Trade Administration Circular Welded Carbon Steel Pipes and Tubes from Thailand: Amended Final... steel pipes and tubes (pipes and tubes) from Thailand, covering the period March 1, 2008 through... published in the Federal Register on October 20, 2010. See Circular Welded Carbon Steel Pipes and Tubes...

  10. 78 FR 64473 - Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of China: Final No...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-29

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of... Preliminary Results of the 2011-2012 administrative review of the antidumping duty order on certain hot- rolled carbon steel flat products (``hot-rolled steel'') from the People's Republic of China (``PRC'').\\1...

  11. 78 FR 42039 - Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of China: Preliminary...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-15

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of... (``Department'') is conducting an administrative review of the antidumping duty order on certain hot- rolled carbon steel flat products (``hot-rolled steel'') from the People's Republic of China (``PRC''),\\1...

  12. 77 FR 32513 - Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From the Russian Federation; Preliminary...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-06-01

    ... International Trade Administration Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From the Russian... Steel Products from the Russian Federation. SUMMARY: In response to a request from Nucor Corporation... Carbon-Quality Steel Products from the Russian Federation (``the Agreement'') for the period July 1, 2010...

  13. 78 FR 76653 - Carbon and Certain Alloy Steel Wire Rod From Brazil, Indonesia, Mexico, Moldova, Trinidad and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-18

    ... Certain Alloy Steel Wire Rod From Brazil, Indonesia, Mexico, Moldova, Trinidad and Tobago, and Ukraine Scheduling of full five-year reviews concerning the countervailing duty order on carbon and certain alloy steel ] wire rod from Brazil and the antidumping duty orders on carbon and certain alloy steel wire...

  14. 78 FR 60316 - Carbon and Certain Alloy Steel Wire Rod From Brazil, Indonesia, Mexico, Moldova, Trinidad and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-01

    ... Certain Alloy Steel Wire Rod From Brazil, Indonesia, Mexico, Moldova, Trinidad and Tobago, and Ukraine... determine whether revocation of the countervailing duty order on carbon and certain alloy steel wire rod from Brazil and antidumping duty orders on carbon and certain alloy steel wire rod from...

  15. 75 FR 57444 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe from the People's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-21

    ... International Trade Administration Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe... alloy steel standard, line, and pressure pipe (``seamless pipe'') from the People's Republic of China... determination. See Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe from the...

  16. 77 FR 66954 - Carbon and Certain Alloy Steel Wire Rod From Mexico: Preliminary Results of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-11-08

    ... International Trade Administration Carbon and Certain Alloy Steel Wire Rod From Mexico: Preliminary Results of... on carbon and certain alloy steel wire rod (wire rod) from Mexico. The period of review is October 1... certain alloy steel wire rod. The product is currently classified under the Harmonized Tariff Schedule...

  17. 77 FR 21968 - Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-12

    ... International Trade Administration Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the... and alloy steel standard, line, and pressure pipe from the People's Republic of China. The period of... countervailing duty order on seamless carbon and alloy steel standard, line, and pressure pipe from the...

  18. 75 FR 69052 - Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the People's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-10

    ... International Trade Administration Certain Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe... Department is issuing an antidumping duty order on certain seamless carbon and alloy steel standard, line... and Alloy Steel Standard, Line, and Pressure Pipe from the People's Republic of China:...

  19. 78 FR 40428 - Certain Hot-Rolled Carbon Steel Flat Products from India: Rescission of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-05

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products from India: Rescission of... administrative review of the antidumping duty order on certain hot- rolled carbon steel flat products (hot rolled... January 30, 2013, the Department initiated an administrative review of hot rolled steel from...

  20. 78 FR 40429 - Certain Hot-Rolled Carbon Steel Flat Products From India: Rescission of Countervailing Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-05

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From India: Rescission of... administrative review of the ] countervailing duty order on certain hot-rolled carbon steel flat products (``hot... Department initiated an administrative review of the countervailing duty order on hot-rolled steel from...

  1. 77 FR 69790 - Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of China: Final Results...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-11-21

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of... Results of the 2010-2011 administrative review of the antidumping duty order on certain hot- rolled carbon steel flat products (``hot-rolled steel'') from the People's Republic of China (``PRC''). The period...

  2. 76 FR 7546 - Certain Hot-Rolled Carbon Steel Flat Products From Brazil: Rescission of Countervailing Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-02-10

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From Brazil: Rescission of... review of the countervailing duty order on certain hot- rolled carbon steel flat products (hot-rolled... published in the Federal Register the countervailing duty order on hot-rolled steel from Brazil....

  3. Microbial Methane Production Associated with Carbon Steel Corrosion in a Nigerian Oil Field.

    PubMed

    Mand, Jaspreet; Park, Hyung S; Okoro, Chuma; Lomans, Bart P; Smith, Seun; Chiejina, Leo; Voordouw, Gerrit

    2015-01-01

    Microbially influenced corrosion (MIC) in oil field pipeline systems can be attributed to many different types of hydrogenotrophic microorganisms including sulfate reducers, methanogens and acetogens. Samples from a low temperature oil reservoir in Nigeria were analyzed using DNA pyrotag sequencing. The microbial community compositions of these samples revealed an abundance of anaerobic methanogenic archaea. Activity of methanogens was demonstrated by incubating samples anaerobically in a basal salts medium, in the presence of carbon steel and carbon dioxide. Methane formation was measured in all enrichments and correlated with metal weight loss. Methanogens were prominently represented in pipeline solids samples, scraped from the inside of a pipeline, comprising over 85% of all pyrosequencing reads. Methane production was only witnessed when carbon steel beads were added to these pipeline solids samples, indicating that no methane was formed as a result of degradation of the oil organics present in these samples. These results were compared to those obtained for samples taken from a low temperature oil field in Canada, which had been incubated with oil, either in the presence or in the absence of carbon steel. Again, methanogens present in these samples catalyzed methane production only when carbon steel was present. Moreover, acetate production was also found in these enrichments only in the presence of carbon steel. From these studies it appears that carbon steel, not oil organics, was the predominant electron donor for acetate production and methane formation in these low temperature oil fields, indicating that the methanogens and acetogens found may contribute significantly to MIC.

  4. Microbial Methane Production Associated with Carbon Steel Corrosion in a Nigerian Oil Field

    PubMed Central

    Mand, Jaspreet; Park, Hyung S.; Okoro, Chuma; Lomans, Bart P.; Smith, Seun; Chiejina, Leo; Voordouw, Gerrit

    2016-01-01

    Microbially influenced corrosion (MIC) in oil field pipeline systems can be attributed to many different types of hydrogenotrophic microorganisms including sulfate reducers, methanogens and acetogens. Samples from a low temperature oil reservoir in Nigeria were analyzed using DNA pyrotag sequencing. The microbial community compositions of these samples revealed an abundance of anaerobic methanogenic archaea. Activity of methanogens was demonstrated by incubating samples anaerobically in a basal salts medium, in the presence of carbon steel and carbon dioxide. Methane formation was measured in all enrichments and correlated with metal weight loss. Methanogens were prominently represented in pipeline solids samples, scraped from the inside of a pipeline, comprising over 85% of all pyrosequencing reads. Methane production was only witnessed when carbon steel beads were added to these pipeline solids samples, indicating that no methane was formed as a result of degradation of the oil organics present in these samples. These results were compared to those obtained for samples taken from a low temperature oil field in Canada, which had been incubated with oil, either in the presence or in the absence of carbon steel. Again, methanogens present in these samples catalyzed methane production only when carbon steel was present. Moreover, acetate production was also found in these enrichments only in the presence of carbon steel. From these studies it appears that carbon steel, not oil organics, was the predominant electron donor for acetate production and methane formation in these low temperature oil fields, indicating that the methanogens and acetogens found may contribute significantly to MIC. PMID:26793176

  5. Polysaccharide from Plantago as a green corrosion inhibitor for carbon steel in 1M HCl solution.

    PubMed

    Mobin, Mohammad; Rizvi, Marziya

    2017-03-15

    Polysaccharide from Plantago ovata was investigated for its inhibition characteristics for carbon steel corrosion in 1M HCl. The mucilage of the Plantago is comprised of a highly branched polysaccharide, arabinosyl (galaturonic acid) rhamnosylxylan (AX), which is mainly responsible for the corrosion inhibition of the carbon steel. The techniques that were used to assess the inhibition and adsorption properties of the AX in the acid solution are gravimetric method, potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), atomic force microscopy (AFM), UV-vis spectroscopy and FTIR. Thermodynamic and activation parameters revealed that the spontaneous adsorption of AX on carbon steel was mixed type and predominantly chemical in nature. Quantum chemical analysis supports the proposed mechanism of inhibition. AX from Plantago could serve as a green corrosion inhibitor for the carbon steel in hydrochloric medium with good inhibition efficiency but low risk of environmental pollution.

  6. Nanosized MX Precipitates in Ultra-Low-Carbon Ferritic/Martensitic Heat-Resistant Steels

    NASA Astrophysics Data System (ADS)

    Yin, Feng-Shi; Jung, Woo-Sang

    2009-02-01

    Nanosized MX precipitates in ultra-low-carbon ferritic/martensitic heat-resistant 9Cr-W-Mo-VNbTiN steels were characterized by transmission electron microscope (TEM) using carbon film replicas. The steels were prepared by vacuum induction melting followed by hot forging and rolling into plates. The plates were normalized at 1100 °C for 1 hour, cooled in air, and tempered at 700 °C for 1 hour. The results show that bimodal nanosized MX precipitates distribute densely and homogeneously in the matrix within martensitic lath after normalizing-and-tempering heat treatment. The larger nanosized MX precipitates with the size of 30 to 50 nm are rich in Nb, while the smaller ones with the size of about 10 nm contain less Nb but more V. Small addition of Ti causes an increase in the number of the larger nanosized MX precipitates. The total number density of the nanosized MX precipitates in the ultra-low-carbon ferritic/martensitic steels is measured to be over 300/ μm2, much higher than that in conventional ferritic/martensitic steels. Short-term creep test results show that the ultra-low-carbon ferritic/martensitic steels with high dense nanosized MX precipitates have much higher creep rupture strength than conventional ASME-P92 steel. The strength degradation of the ultra-low-carbon ferritic/martensitic heat-resistant steels during creep is also discussed in this article.

  7. Effect of Different Casting Parameters on the Cleanliness of High Manganese Steel Ingots Compared to High Carbon Steel

    NASA Astrophysics Data System (ADS)

    von Schweinichen, Petrico; Chen, Zhiye; Senk, Dieter; Lob, Alexander

    2013-12-01

    The increasing demand for excellent steel properties has led to the creation of new steel grades such as high manganese TWIP and TRIP steels which are scientifically examined in Germany within the international research framework of the SFB 761 "Steel-ab initio." The production of these high-technology products, utilizing mainly the ingot-casting method, leads to new challenges in the prevention of cast defects. At RWTH Aachen University, a systematic investigation of the solidification process as it relates to shrinkage cavity, macrosegregation, cleanliness, and surface imperfections in as-cast ingots is being conducted. A particular attention was devoted to the effects of such casting parameters as superheat, pouring rate, hot top, and stirring conditions on the solidification and cleanliness of low carbon alloyed and high manganese alloyed steels. The experimental results show that rising manganese content leads to a higher amount and larger size of inclusions while rising carbon content enhances the inclusion generation in the same way. It was found that a bottom teeming system combined with an inert gas atmosphere produces the best quality and that if casting is performed with a runner-system, it is important to use a SiO2-free refractory to avoid oxidizing the Mn content of the melt to MnO inclusions by redox-reactions.

  8. Carbonation of steel slag for CO2 sequestration: leaching of products and reaction mechanisms.

    PubMed

    Huijgen, Wouter J J; Comans, Rob N J

    2006-04-15

    Carbonation of industrial alkaline residues can be used as a CO2 sequestration technology to reduce carbon dioxide emissions. In this study, steel slag samples were carbonated to a varying extent. Leaching experiments and geochemical modeling were used to identify solubility-controlling processes of major and trace elements, both with regard to carbonation mechanisms and the environmental properties of the (carbonated) steel slag. Carbonation was shown to reduce the leaching of alkaline earth metals (except Mg) by conversion of Ca-phases, such as portlandite, ettringite, and Ca-(Fe)-silicates into calcite, possibly containing traces of Ba and Sr. The leaching of vanadium increased substantially upon carbonation, probably due to the dissolution of a Ca-vanadate. The reactive surface area of Al- and Fe-(hydr)oxides increased with the carbonation degree, which tends to reduce the leaching of sorption-controlled trace elements. Sorption on Mn- (hydr)oxides was found to be required to adequately model the leaching of divalent cations, but was not influenced by carbonation. Consideration of these three distinct reactive surfaces and possible (surface) precipitation reactions resulted in adequate modeling predictions of oxyanion and trace metal leaching from (carbonated) steel slag. Hence, these surfaces exert a major influence on the environmental properties of both fresh and carbonated steel slag.

  9. Effect of solidification path and contraction on the cracking susceptibility of carbon peritectic steels

    NASA Astrophysics Data System (ADS)

    Trejo, Martin Herrera; Lopez, Eddy Alfaro; Ruiz Mondragon, Jose Jorge; Castro Roman, Manuel de Jesus; Tovar, Hugo Solis

    2010-10-01

    The solidification path and contraction generated during the solidification of three carbon steels were studied. Two of the carbon steels were of hypo-peritectic chemical composition, with 0.11 % C and 0.15 % C, while one of the carbon steels were hyper-peritectic with 0.16 % C. The steels with 0.11 % C and 0.16 % C solidified as expected due to their chemical composition. In contrast, the chemically hypo-peritectic steel with 0.15 % C solidified as hyper-peritectic steel, which was associated with the microsegregation of Mn. For the steel exhibiting a hypo-peritectic solidification path, peritectic transformation occurred at solid fraction values higher than 0.9, where it was assumed that the contraction generated in the mushy shell cannot be fed by the liquid. However, for steels exhibiting a hyper-peritectic solidification path, peritectic transformation began at solid fraction values lower than 0.9, where the contraction generated by the peritectic transformation was partly fed by the liquid. Hence, the highest cracking susceptibility was associated with the hypo-peritectic solidification mode.

  10. Effects of hydrogen on carbon steels at the Multi-Function Waste Tank Facility

    SciTech Connect

    Carlos, W.C.

    1995-02-08

    Concern has been expressed that hydrogen produced by corrosion, radiolysis, and decomposition of the waste could cause embrittlement of the carbon steel waste tanks at Hanford. The concern centers on the supposition that the hydrogen evolved in many of the existing tanks might penetrate the steel wall of the tank and cause embrittlement that might lead to catastrophic failure. This document reviews literature on the effects of hydrogen on the carbon steel proposed for use in the Multi-Function Waste Tank Facility for the time periods before and during construction as well as for the operational life of the tanks. The document draws several conclusions about these effects. Molecular hydrogen is not a concern because it is not capable of entering the steel tank wall. Nascent hydrogen produced by corrosion reactions will not embrittle the steel because the mild steel used in tank construction is not hard enough to be susceptible to hydrogen stress cracking and the corrosion product hydrogen is not produced at a rate sufficient to cause either loss in tensile ductility or blistering. If the steel intended for use in the tanks is produced to current technology, fabricated in accordance with good construction practice, postweld heat treated, and operated within the operating limits defined, hydrogen will not adversely affect the carbon steel tanks during their 50-year design life. 26 refs.

  11. High strength, low carbon, dual phase steel rods and wires and process for making same

    DOEpatents

    Thomas, Gareth; Nakagawa, Alvin H.

    1986-01-01

    A high strength, high ductility, low carbon, dual phase steel wire, bar or rod and process for making the same is provided. The steel wire, bar or rod is produced by cold drawing to the desired diameter in a single multipass operation a low carbon steel composition characterized by a duplex microstructure consisting essentially of a strong second phase dispersed in a soft ferrite matrix with a microstructure and morphology having sufficient cold formability to allow reductions in cross-sectional area of up to about 99.9%. Tensile strengths of at least 120 ksi to over 400 ksi may be obtained.

  12. Competitive graphitization and diamond growth on hot-dip aluminized carbon steel substrate

    NASA Astrophysics Data System (ADS)

    Li, Y. S.; Ma, H. T.; Yang, L. Z.; Zhang, C. Z.; Feng, R. F.; Yang, Q.; Hirose, A.

    2014-09-01

    When carbon steel is directly exposed in 99%H2-1%CH4 gas mixture for plasma enhanced CVD deposition of diamond coatings, an intermediate graphite layer is preferentially formed on the substrate surface, and the substrate is subjected to a severe internal carburization attack. The diamond coatings formed easily delaminate from the steel substrate. Hot dip aluminizing treatment of the carbon steel has markedly promoted diamond nucleation, growth and interfacial adhesion. The formation of graphite intermediate phase on the substrate surface is effectively inhibited and the substrate carburization is also suppressed. The possible mechanism of this transition is discussed based on a series of analytical techniques.

  13. Structure, phase transformations, mechanical characteristics, and cold resistance of low-carbon martensitic steels

    NASA Astrophysics Data System (ADS)

    Kozvonin, V. A.; Shatsov, A. A.; Ryaposov, I. V.; Zakirova, M. G.; Generalova, K. N.

    2016-08-01

    Temper-resistant low-carbon Cr-Mn-Ni-Mo-V-Nb steels with concentrations of carbon of 0.15 and 0.27 wt % have been studied. It has been shown that, upon quenching, various morphological types of the α phase can be formed. The structure of the steels is stable in the course of heating below critical temperatures and remains a lath-type structure in the intercritical temperature range. Specific features of structural and phase transformations, as well as the dependence of the mechanical characteristics of the steels, on the tempering temperature have been determined.

  14. Determination of free nitrogen in carbon steels by inert gas fusion method

    NASA Astrophysics Data System (ADS)

    Tabakov, Ya. I.; Grigorovich, K. V.; Mansurova, E. R.

    2016-07-01

    The possibility to use hot extraction (thermal extraction in a carrier-gas flow) for fractional analysis of nitrogen in carbon steels is shown for cord and reinforcing-bar steels. A rapid procedure is developed for an analysis of free nitrogen in carbon steels. The validity of the analytical procedure is confirmed by high-temperature hydrogen extraction. The data obtained by the two methods correlate well with each other. A sample preparation procedure is developed for the determination of the content of dissolved nitrogen.

  15. Microstructure and properties of pure iron/copper composite cladding layers on carbon steel

    NASA Astrophysics Data System (ADS)

    Wan, Long; Huang, Yong-xian; Lü, Shi-xiong; Huang, Ti-fang; Lü, Zong-liang

    2016-08-01

    In the present study, pure iron/copper composite metal cladding was deposited onto carbon steel by tungsten inert gas welding. The study focused on interfacial morphological, microstructural, and mechanical analyses of the composite cladding layers. Iron liquid-solid-phase zones were formed at copper/steel and iron interfaces because of the melting of the steel substrate and iron. Iron concentrated in the copper cladding layer was observed to exhibit belt, globule, and dendrite morphologies. The appearance of iron-rich globules indicated the occurrence of liquid phase separation (LPS) prior to solidification, and iron-rich dendrites crystallized without the occurrence of LPS. The maximum microhardness of the iron/steel interface was lower than that of the copper/steel interface because of the diffusion of elemental carbon. All samples fractured in the cladding layers. Because of a relatively lower strength of the copper layer, a short plateau region appeared when shear movement was from copper to iron.

  16. Kinetics of strain aging in bake hardening ultra low carbon steel—a comparison with low carbon steel

    NASA Astrophysics Data System (ADS)

    de, A. K.; de Cooman, B. C.; Vandeputte, S.

    2001-10-01

    The kinetics of the static strain aging process have been analyzed in a vacuum-degassed ultra low carbon bake hardenable (ULC BH) steel with a total carbon content of 20 wt.ppm through measurement of the strength properties. The influence of prestrain and free interstitial carbon content has been studied. The kinetic results were compared with those of a BH low carbon (LC) steel. In the derivation of the time exponent and the activation energy, only the first stage of aging was considered. It was observed that, at all prestrain levels and matrix solute carbon contents, the initial aging process in the ULC steel obeyed the t 2/3 kinetic law and the kinetics were not influenced by the changes in dislocation structure due to prestrain and the dissolved carbon content. In comparison, the aging process and the kinetics in the LC steel were found to be significantly influenced by the amount of prestrain. The presence of carbide particles in LC steels can modify the aging kinetics.

  17. The structural dependence of work hardening in low carbon steels

    SciTech Connect

    Johnson, Patricia Elizabeth

    1991-12-01

    The influence of the dislocation cell structure on the work hardening behavior of low carbon steel sheets was investigated. Specimens were prestrained at low temperature to suppress cell formation and their subsequent behavior was compared with results of isothermal reference tests. It was found that the extent of cell development has little or no influence on the plastic behavior at room temperature and below. Interrupted temperature, tensile-shear tests demonstrated further that the transient behavior induced by loading path changes is also not strongly associated with the cell walls. In-situ straining studies indicate that the factor controlling the flow stress at room temperature is the limited mobility of screw dislocations moving the cell interiors, and not dislocation interactions with the cell walls. The unique properties of a/2<111> screw dislocations are known to dominate low temperature deformation behavior in bcc metals. The current work indicates that these dislocations may still control the flow stress at intermediate temperatures, even in the presence of a developed cell structure.

  18. The structural dependence of work hardening in low carbon steels

    SciTech Connect

    Johnson, P.E.

    1991-12-01

    The influence of the dislocation cell structure on the work hardening behavior of low carbon steel sheets was investigated. Specimens were prestrained at low temperature to suppress cell formation and their subsequent behavior was compared with results of isothermal reference tests. It was found that the extent of cell development has little or no influence on the plastic behavior at room temperature and below. Interrupted temperature, tensile-shear tests demonstrated further that the transient behavior induced by loading path changes is also not strongly associated with the cell walls. In-situ straining studies indicate that the factor controlling the flow stress at room temperature is the limited mobility of screw dislocations moving the cell interiors, and not dislocation interactions with the cell walls. The unique properties of a/2<111> screw dislocations are known to dominate low temperature deformation behavior in bcc metals. The current work indicates that these dislocations may still control the flow stress at intermediate temperatures, even in the presence of a developed cell structure.

  19. Optimization of fatigue damage indication in ferromagnetic low carbon steel

    NASA Astrophysics Data System (ADS)

    Tomáš, Ivan; Kovářík, Ondřej; Kadlecová, Jana; Vértesy, Gábor

    2015-09-01

    Fatigue damage was investigated by the method of magnetic adaptive testing (MAT), which is based on the systematic measurement and evaluation of minor magnetic hysteresis loops. A large number of magnetic measurements were performed on a single reference series of low carbon steel flat samples, which were fatigued by cyclic bending in an identical way, up to an increasing level of fatigue damage. The measurements of the magnetic properties of these samples were repeated under varied conditions, including speed of magnetization of the samples, sample temperature during the measurement, choice of the evaluated signal, frequency of the voltage sampling, and range of the applied amplitudes of the magnetizing field/current. Special attention was turned to the influence of the thickness of the non-ferromagnetic spacers positioned between the surface of the samples and the flat fronts of the attached magnetizing yokes. On one hand, the spacers decrease the values of the induced signal and its derivatives, but on the other hand they substantially increase the reproducibility of the measurement and positively influence the shapes of the resulting degradation curves. Optimum conditions for the magnetic measurement of the fatigue damage were searched, found, and recommended. The results indicate the reliable applicability of MAT to detect early stages of the material fatigue, and to predict its residual lifetime.

  20. Corrosion of Carbon Steel and Corrosion-Resistant Rebars in Concrete Structures Under Chloride Ion Attack

    NASA Astrophysics Data System (ADS)

    Mohamed, Nedal; Boulfiza, Mohamed; Evitts, Richard

    2013-03-01

    Corrosion of reinforced concrete is the most challenging durability problem that threatens reinforced concrete structures, especially structures that are subject to severe environmental conditions (i.e., highway bridges, marine structures, etc.). Corrosion of reinforcing steel leads to cracking and spalling of the concrete cover and billions of dollars are spent every year on repairing such damaged structures. New types of reinforcements have been developed to avoid these high-cost repairs. Thus, it is important to study the corrosion behavior of these new types of reinforcements and compare them to the traditional carbon steel reinforcements. This study aimed at characterizing the corrosion behavior of three competing reinforcing steels; conventional carbon steel, micro-composite steel (MMFX-2) and 316LN stainless steel, through experiments in carbonated and non-carbonated concrete exposed to chloride-laden environments. Synthetic pore water solutions have been used to simulate both cases of sound and carbonated concrete under chloride ions attack. A three-electrode corrosion cell is used for determining the corrosion characteristics and rates. Multiple electrochemical techniques were applied using a Gamry PC4™ potentiostat manufactured by Gamry Instruments (Warminster, PA). DC corrosion measurements were applied on samples subjected to fixed chloride concentration in the solution.

  1. 78 FR 9676 - Circular Welded Carbon Quality Steel Pipe From the People's Republic of China: Rescission of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-02-11

    ... International Trade Administration Circular Welded Carbon Quality Steel Pipe From the People's Republic of China...'') is rescinding the administrative review of the countervailing duty order on circular welded carbon... countervailing duty order on circular welded carbon quality steel pipe from the PRC covering the period January 1...

  2. 77 FR 43806 - Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-26

    ... International Trade Administration Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the... Department) initiated an administrative review of the antidumping duty order on seamless carbon and alloy... carbon and alloy steel standard, line, and pressure pipe from the People's Republic of China covering...

  3. The effect of metal microstructure on the initial attachment of Escherichia coli to 1010 carbon steel.

    PubMed

    Javed, M A; Stoddart, P R; McArthur, S L; Wade, S A

    2013-09-01

    Metallurgical features have been shown to play an important role in the attachment of microorganisms to metal surfaces. In the present study, the influence of the microstructure of as-received (AR) and heat-treated (HT) 1010 carbon steel on the initial attachment of bacteria was investigated. Heat treatment was carried out with the aim of increasing the grain size of the carbon steel coupons. Mirror-polished carbon steel coupons were immersed in a minimal medium inoculated with Escherichia coli (ATCC 25922) to investigate the early (15, 30 and 60 min) and relatively longer-term (4 h) stages of bacterial attachment. The results showed preferential colonisation of bacteria on the grain boundaries of the steel coupons. The bacterial attachment to AR steel coupons was relatively uniform compared to the HT steel coupons where an increased number of localised aggregates of bacteria were found. Quantitative analysis showed that the ratio of the total number of isolated (i.e., single) bacteria to the number of bacteria in aggregates was significantly higher on the AR coupons than the HT coupons. Longer-term immersion studies showed production of extracellular polymeric substances by the bacteria and corrosion at the grain boundaries on both types of steel coupon tested.

  4. Research Concerning The Mechanical And Structural Properties Of Warm Rolled Construction Carbon Steels

    SciTech Connect

    Medrea, C.; Negrea, G.; Domsa, S.

    2007-04-07

    Construction carbon steels represent an important steel class due to the large quantity in which it is produced. Generally, these steels are delivered in as-rolled or normalized condition heaving a ferrite-pearlite microstructure. For a given chemical composition, the mechanical characteristics of this microstructure are largely influenced by the grain size. Rolling is the deformation process which is most widely used for grain size refinement. Situated in the intermediate temperature range, warm-rolling presents certain advantages as compared to classical hot- or cold-working processes.The paper presents a study on the microstructure and mechanical properties of Ck15 carbon steel samples warm-rolled. After deformation, the microstructure was investigated by light microscopy. Hardness measurements were made on the section parallel to the rolling direction. The mechanical properties of the steel after warm-rolling were assessed by tensile and impact tests. Additional information concerning the fracture behavior of warm-rolled samples was obtained by examining the fracture surface by scanning electron microscopy. The microstructure of the steel proved to have good mechanical properties. By considering the technologic and energy aspects, the paper shows that warm-rolling can lead to the improvement of mechanical properties of construction carbon steels.

  5. Microstructure and crack resistance of low carbon Cr-Ni and Cr-Ni-W steel after austempering

    NASA Astrophysics Data System (ADS)

    Avdjieva, Tatyana; Tsutsumanova, Gichka; Russev, Stoyan; Staevski, Konstantin

    2013-09-01

    The microstructure of the low carbon Cr-Ni steel after slow cooling from austenization temperature represents a mix of granulated bainite with islands from carbon-rich martensite and carbon-poor austenite. After quick cooling throwing in salt bath from austenization temperature the microstructure is lath bainite. However, in the same treatment conditions, the microstructure of the low carbon Cr-Ni-W steel is different — clusters consist from lath ferrite and retained austenite, disposed in the frame of parent's austenite grains. The cooling velocity has no effect upon the structure making. The impact toughness of the steel with tungsten content is bigger than the steel without tungsten.

  6. Enhanced Corrosion Resistance of Carbon Steel in Hydrochloric Acid Solution by Eriobotrya Japonica Thunb. Leaf Extract: Electrochemical Study

    PubMed Central

    Yang, Wenjing; Wang, Qihui; Xu, Ke; Yin, Yanjun; Bao, Hebin; Li, Xueming; Niu, Lidan; Chen, Shiqi

    2017-01-01

    The biodegradable inhibitors, which could effectively reduce the rate of corrosion of carbon steel, were investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The mixed-type inhibitors extracted from Eriobotrya japonica Thunb. leaf exhibited excellent inhibition performance, and the inhibition efficiency for carbon steel reached 90.0% at 298 K in hydrochloric acid. Moreover, the adsorption mechanism of the inhibitors on a carbon steel surface is described by the Langmuir adsorption isotherm. Simultaneously, the corrosion morphology of the carbon steel and the inhibitor structure were analyzed by scanning electron microscope (SEM) and Fourier transform infrared spectroscopy (FT-IR), respectively. PMID:28812993

  7. Biocidal effect of cathodic protection on bacterial viability in biofilm attached to carbon steel.

    PubMed

    Miyanaga, Kazuhiko; Terashi, Ryosuke; Kawai, Hirofumi; Unno, Hajime; Tanji, Yasunori

    2007-07-01

    Biofilm formed on carbon steel by various species of bacterial cells causes serious problems such as corrosion of steel, choking of flow in the pipe, deterioration of the heat-transfer efficiency, and so on. Cathodic protection is known to be a reliable method for protecting carbon steel from corrosion. However, the initial attachment of bacteria to the surface and the effects of cathodic protection on bacterial viability in the biofilm have not been clarified. In this study, cathodic protection was applied to an artificial biofilm containing Pseudomonas aeruginosa (PAO1), a biofilm constituent, on carbon steel. The aims of this study were to evaluate the inhibition effect of cathodic protection on biofilm formation and to reveal the inhibition mechanisms. The viability of PAO1 in artificial biofilm of 5 mm thickness on cathodically protected steel decreased to 1% of the initial cell concentration. Analysis of pH distribution in the artificial biofilm by pH microelectrode revealed that pH in proximity to carbon steel increased to approximately 11 after cathodic protection for 5 h. Moreover, 99% of region in the artificial biofilm was under the pH conditions of over nine. A simulation of pH profile was shown to correspond to experimental values. These results indicate cells in the artificial biofilm were killed or damaged by cathodic protection due to pH increase.

  8. The effects of water on the passive behavior of 1018 carbon steel in organic solutions

    SciTech Connect

    Shifler, D.A.; Kruger, J. . Dept. of Materials Science and Engineering); Moran, P.J. . Dept. of Mechanical Engineering)

    1994-04-01

    The passivation and breakdown behavior of 1018 carbon steel in propylene carbonate (PC) or dimethoxyethane (DME) mixtures with water and containing 0.5M LiAsF[sub 6] were studied. The behavior of the steel in the organic solvent/water mixtures was highly dependent on the organic solvent. The anodic polarization of carbon steel displayed active-passive behavior in 10--90 mole percent (m/o) PC/H[sub 2]O mixtures and a tenuous degree of stability within the passive range. The anodic polarization of carbon steel displayed no active-passive behavior in 50--90 m/o DME/H[sub 2]O mixtures and displayed active-passive behavior in 10--30 m/o DME/H[sub 2]O mixtures. The steel was stable within the passive range of these DME/H[sub 2]O solutions. The breakdown potential of the steel in DME/H[sub 2]O mixtures is more electropositive than the oxidation potential of the DME solvent at all molar ratios.

  9. A STUDY OF CORROSION AND STRESS CORROSION CRACKING OF CARBON STEEL NUCLEAR WASTE STORAGE TANKS

    SciTech Connect

    BOOMER, K.D.

    2007-08-21

    The Hanford reservation Tank Farms in Washington State has 177 underground storage tanks that contain approximately 50 million gallons of liquid legacy radioactive waste from cold war plutonium production. These tanks will continue to store waste until it is treated and disposed. These nuclear wastes were converted to highly alkaline pH wastes to protect the carbon steel storage tanks from corrosion. However, the carbon steel is still susceptible to localized corrosion and stress corrosion cracking. The waste chemistry varies from tank to tank, and contains various combinations of hydroxide, nitrate, nitrite, chloride, carbonate, aluminate and other species. The effect of each of these species and any synergistic effects on localized corrosion and stress corrosion cracking of carbon steel have been investigated with electrochemical polarization, slow strain rate, and crack growth rate testing. The effect of solution chemistry, pH, temperature and applied potential are all considered and their role in the corrosion behavior will be discussed.

  10. Effect of silicon on the spheroidization of cementite in hypereutectoid high carbon chromium bearing steels

    NASA Astrophysics Data System (ADS)

    Kim, Kwan-Ho; Lee, Jae-Seung; Lee, Duk-Lak

    2010-12-01

    The effect of silicon on the spheroidization of cementite in hypereutectoid high carbon chromium bearing steels has been investigated on the basis of microstructural analysis and thermodynamic calculations. The results showed that an increase of silicon content in high carbon chromium bearing steels retards the spheoridization of cementite. The thermodynamic calculations revealed that the shrinkage of the austenite phase field in bearing steels with increasing silicon content gave rise to an increase of volume fraction of cementite at an annealing temperature, possibly resulting in incomplete spheroidization. Furthermore, due to the low solubility of silicon in cementite, an increase of silicon content can raise the activity or chemical potential of carbon atoms in austenite at the austenite/cementite interfaces. Consequently, the difference in chemical potential of carbon atoms at the interfaces would be reduced with increasing silicon content, causing a decrease of the driving force for their diffusion from cementite to austenite.

  11. Corrosion Evaluation of Carbon Steels Using Nondestructive Technique

    NASA Astrophysics Data System (ADS)

    Lee, Jin Kyung; Lee, Sang Pill; Lee, Moon Hee; Lee, Joon Hyun; Park, Jun Young

    Primary water stress corrosion crack (PWSCC) in the piping used at the nuclear power plant has been one of the major issues for the safety of plant. The major objective in this paper is to clarify the corrosion degree and damage by the PWSCC using nondestructive technique. The instrument of the tube typed reactor with the internal conditions of the temperature of 473K under pressure of 10 MPa was designed for corrosion of the material. The tensile specimens of the same material with the reactor were corroded in the reactor for evaluation of mechanical properties according to the corrosion. The corrosion of the specimen was maintained over one year, and an acoustic emission technique was applied to inspect the corrosion damage of the specimen periodically. A tensile test was performed for the corroded specimen, and then the elastic waves caused the deformation of the corroded specimen were analyzed. With the increase of the corrosion time the elastic waves generated in the specimen due to the tensile load showed a little difference, and these differences of the waves work as a cause of the change of acoustic emission (AE) parameters. The number of AE events at the beginning of the load increased with the corrosion time. AE parameters of amplitude and energy decreased as the corrosion times increased, while the level of duration time and count were increased with the corrosion periods. The velocity and attenuation of the elastic wave were also analyzed for the specimen, and these factors showed a close relation with the corrosion times. In addition, SEM and XRD analysis were performed to evaluate the damage behavior of the carbon steel due to corrosion.

  12. Installation of adhesively bonded composites to repair carbon steel structure.

    SciTech Connect

    Roach, Dennis Patrick; Dunn, Dennis P.; Rackow, Kirk A.

    2003-02-01

    In the past decade, an advanced composite repair technology has made great strides in commercial aviation use. Extensive testing and analysis, through joint programs between the Sandia Labs FAA Airworthiness Assurance Center and the aviation industry, have proven that composite materials can be used to repair damaged aluminum structure. Successful pilot programs have produced flight performance history to establish the viability and durability of bonded composite patches as a permanent repair on commercial aircraft structures. With this foundation in place, efforts are underway to adapt bonded composite repair technology to civil structures. This paper presents a study in the application of composite patches on large trucks and hydraulic shovels typically used in mining operations. Extreme fatigue, temperature, erosive, and corrosive environments induce an array of equipment damage. The current weld repair techniques for these structures provide a fatigue life that is inferior to that of the original plate. Subsequent cracking must be revisited on a regular basis. It is believed that the use of composite doublers, which do not have brittle fracture problems such as those inherent in welds, will help extend the structure's fatigue life and reduce the equipment downtime. Two of the main issues for adapting aircraft composite repairs to civil applications are developing an installation technique for carbon steel structure and accommodating large repairs on extremely thick structures. This paper will focus on the first phase of this study which evaluated the performance of different mechanical and chemical surface preparation techniques. The factors influencing the durability of composite patches in severe field environments will be discussed along with related laminate design and installation issues.

  13. Homopolar pulse welding of API 5L carbon steel linepipe

    SciTech Connect

    Haase, P.; Carnes, R.; Harville, M.

    1994-12-31

    Homopolar pulse welding (HPW) is a resistance welding process being investigated as a method to rapidly join API 5L carbon steel linepipe. The target application for this investigation is deepwater offshore pipeline construction utilizing the J-lay method, which requires a rapid one-shot welding process for economic feasibility. HPW utilizes the high current, low-voltage pulse produced by a homopolar generator to rapidly resistance heat the interface between abutting workpieces, and follows that pulse with an upset action to produce a weld. A large number of controllable parameters affecting the quality of the resultant weld are present in the process. Three inch nominal diameter, schedule 160 API 5L X-52 pipe sections were welded in this series while controlling variations in generator discharge speed electrode location and upsetting parameters. Welding current voltage and temperature curves were recorded for the welds. Tensile and Charpy V-notch impact specimens were machined from each weld and tested. Weld cross-sections were macroscopically examined. By delaying the application of the forging action, the `white line` or decarburized zone commonly found in high frequency resistance or flash butt welds was eliminated. Weld tensile strength was found to be primarily dependent on generator discharge speed (heat input). Electrode distance from the weld interface was found to be the critical factor determining weld zone cooling rate. HPW parameters can be selected to produce welds without the `white line` or decarburized zone commonly found in high frequency resistance and flash butt welds. Full tensile strength welds are easily achieved providing two conditions are met: sufficient heat input is supplied and a nominal upsetting action is applied within a few seconds of the discharge current peak. Electrode location provides control over the weld zone cooling rate.

  14. Precipitation and fine structure in medium-carbon vanadium and vanadium/niobium microalloyed steels

    NASA Astrophysics Data System (ADS)

    Thompson, S. W.; Krauss, G.

    1989-11-01

    Hot-rolled and continuously cooled, medium-carbon microalloyed steels containing 0.2 or 0.4 pct C with vanadium (0.15 pct) or vanadium (0.15 pct) plus niobium (0.04 pct) additions were investigated with light and transmission electron microscopy. Energy dispersive spectroscopy in a scanning transmission electron microscope was conducted on precipitates of the 0.4 pct C steel with vanadium and niobium additions. The vanadium steels contained fine interphase precipitates within ferrite, pearlite nodules devoid of interphase precipitates, and fine ferritic transformation twins. The vanadium plus niobium steels contained large Nb-rich precipitates, precipitates which formed in cellular arrays on deformed austenite substructure and contained about equal amounts of niobium and vanadium, and V-rich interphase precipitates. Transformation twins in the ferrite and interphase precipitates in the pearlitic ferrite were not observed in either of the steels containing both microalloying elements. Consistent with the effect of higher C concentrations on driving the microalloying precipitation reactions, substructure precipitation was much more frequently observed in the 0.4C-V-Nb steel than in the 0.2C-V-Nb steel, both in the ferritic and pearlitic regions of the microstructure. Also, superposition of interphase and substructure precipitation was more frequently observed in the high-C-V-Nb steel than in the similar low-C steel.

  15. Can Thermally Sprayed Aluminum (TSA) Mitigate Corrosion of Carbon Steel in Carbon Capture and Storage (CCS) Environments?

    NASA Astrophysics Data System (ADS)

    Paul, S.; Syrek-Gerstenkorn, B.

    2017-01-01

    Transport of CO2 for carbon capture and storage (CCS) uses low-cost carbon steel pipelines owing to their negligible corrosion rates in dry CO2. However, in the presence of liquid water, CO2 forms corrosive carbonic acid. In order to mitigate wet CO2 corrosion, use of expensive corrosion-resistant alloys is recommended; however, the increased cost makes such selection economically unfeasible; hence, new corrosion mitigation methods are sought. One such method is the use of thermally sprayed aluminum (TSA), which has been used to mitigate corrosion of carbon steel in seawater, but there are concerns regarding its suitability in CO2-containing solutions. A 30-day test was carried out during which carbon steel specimens arc-sprayed with aluminum were immersed in deionized water at ambient temperature bubbled with 0.1 MPa CO2. The acidity (pH) and potential were continuously monitored, and the amount of dissolved Al3+ ions was measured after completion of the test. Some dissolution of TSA occurred in the test solution leading to nominal loss in coating thickness. Potential measurements revealed that polarity reversal occurs during the initial stages of exposure which could lead to preferential dissolution of carbon steel in the case of coating damage. Thus, one needs to be careful while using TSA in CCS environments.

  16. Transformation process for production of ultrahigh carbon steels and new alloys

    DOEpatents

    Strum, M.J.; Goldberg, A.; Sherby, O.D.; Landingham, R.L.

    1995-08-29

    Ultrahigh carbon steels with superplastic properties are produced by heating a steel containing ferrite and carbide phases to a soaking temperature approximately 50 C above the A{sub 1} transformation temperature, soaking the steel above the A{sub 1} temperature for a sufficient time that the major portion of the carbides dissolve into the austenite matrix, and then cooling the steel in a controlled manner within predetermined limits of cooling rate or transformation temperature, to obtain a steel having substantially spheroidal carbides. New alloy compositions contain aluminum and solute additions which promote the formation of a fine grain size and improve the resistance of the carbides to coarsening at the forming temperature. 9 figs.

  17. Transformation process for production of ultrahigh carbon steels and new alloys

    DOEpatents

    Strum, Michael J.; Goldberg, Alfred; Sherby, Oleg D.; Landingham, Richard L.

    1995-01-01

    Ultrahigh carbon steels with superplastic properties are produced by heating a steel containing ferrite and carbide phases to a soaking temperature approximately 50.degree. C. above the A.sub.1 transformation temperature, soaking the steel above the A.sub.1 temperature for a sufficient time that the major portion of the carbides dissolve into the austenite matrix, and then cooling the steel in a controlled manner within predetermined limits of cooling rate or transformation temperature, to obtain a steel having substantially spheroidal carbides. New alloy compositions contain aluminum and solute additions which promote the formation of a fine grain size and improve the resistance of the carbides to coarsening at the forming temperature.

  18. Mathematical modeling and validation of the carburizing of low carbon steels

    NASA Astrophysics Data System (ADS)

    García Mariaca, A.; Cendales, E. D.; Chamarraví, O.

    2016-02-01

    This paper shows the mathematical modeling of heat and mass transfer in transient state of cylindrical bars of low carbon steel subjected to carburizing process. The model solution for the two phenomena was performed using a one-dimensional analysis in the radius direction, using the numerical method of finite differences; also a sensitivity analysis by varying the coefficient of convective heat transfer (h) is performed. The modeling results show that this carburization steel is strongly dependent on h. These results suggest that if it can increase the value of h in this kind of process could reduce the time of process for this heat treatment. Additionally, an experimental procedure was established by carburization of a steel AISI SAE 1010, which develops cementing solid phase and the specimen steel and micrographic hardness profiles obtained from samples of the specimen analysis was performed, to determine the penetration depth of the carbon and validate this result over the values obtained by the computer model.

  19. Corrosion of stainless and carbon steels in molten mixtures of industrial nitrates

    SciTech Connect

    Goods, S.H.; Bradshaw, R.W.; Prairie, M.R.; Chavez, J.M.

    1994-03-01

    Corrosion behavior of two stainless steels and carbon steel in mixtures of NaNO{sub 3} and KNO{sub 3} was evaluated to determine if impurities found in commodity grades of alkali nitrates aggravate corrosivity as applicable to an advanced solar thermal energy system. Corrosion tests were conducted for 7000 hours with Types 304 and 316 stainless steels at 570C and A36 carbon steel at 316C in seven mixtures of NaNO{sub 3} and KNO{sub 3} containing variations in impurity concentrations. Corrosion tests were also conducted in a ternary mixture of NaNO{sub 3}, KNO{sub 3}, and Ca(NO{sub 3}){sub 2}. Corrosion rates were determined by descaled weight losses while oxidation products were examined by scanning electron microscopy, electron microprobe analysis, and X-ray diffraction. The nitrate mixtures were periodically analyzed for changes in impurity concentrations and for soluble corrosion products.

  20. 75 FR 42782 - Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-22

    ... COMMISSION Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia AGENCY: United... Brazil and Japan, and the suspended investigation on hot-rolled steel from Russia. SUMMARY: The... Japan, and the suspended investigation on hot-rolled steel from Russia would be likely to lead to...

  1. 75 FR 16504 - Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-01

    ... COMMISSION Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia AGENCY: United...'') from Brazil, the antidumping duty orders on hot-rolled steel from Brazil and Japan, and the suspended... antidumping duty orders on hot-rolled steel from Brazil and Japan, and the suspended investigation on hot...

  2. 78 FR 60850 - Carbon and Certain Alloy Steel Wire Rod From Brazil: Final Results of the Expedited Second Sunset...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-02

    ... International Trade Administration Carbon and Certain Alloy Steel Wire Rod From Brazil: Final Results of the... certain alloy steel wire rod (wire rod) from Brazil would be likely to lead to continuation or recurrence... Alloy Steel Wire Rod from Brazil, 67 FR 55805 (August 30, 2002). \\2\\ See Initiation of...

  3. 77 FR 41967 - Certain Circular Welded Carbon Steel Pipes and Tubes From India, Thailand, and Turkey; Certain...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-17

    ..., and Turkey; Certain Circular Welded Non-Alloy Steel Pipe From Brazil, Mexico, the Republic of Korea... pipes and tubes from India, Thailand, and Turkey; (2) certain circular welded non-alloy steel pipe from... welded carbon steel pipes and tubes from India, Thailand, and Turkey, certain circular welded...

  4. Segregation of rare earth during isothermal transformation in low carbon steels

    SciTech Connect

    Lu Wei, Liu He; Hsu, T.Y.; Xu Zuyao )

    1993-07-15

    The distribution of rare earth elements (RE) in steel is a significant topic tied to its application. It has been known that there is segregation of RE in austenite grain boundary. Liu and Hsu supposed that RE might segregate at interphase boundaries and influence the kinetics of isothermal transformation. In this investigation, the segregation of RE in proeutectoid ferrite, pearlite and granular bainite, combined with its effect on their kinetics in two low carbon steels is studied by means of SEM-EDAX.

  5. Control of microbiological corrosion on carbon steel with sodium hypochlorite and biopolymer.

    PubMed

    Oliveira, Sara H; Lima, Maria Alice G A; França, Francisca P; Vieira, Magda R S; Silva, Pulkra; Urtiga Filho, Severino L

    2016-07-01

    In the present work, the interaction of a mixture of a biocide, sodium hypochlorite (NaClO), and a biopolymer, xanthan, with carbon steel coupons exposed to seawater in a turbulent flow regime was studied. The cell concentrations, corrosion rates, biomasses, and exopolysaccharides (EPSs) produced on the coupon surfaces with the various treatments were quantified. The corrosion products were evaluated using X-ray diffraction (XRD), and the surfaces of steels were analysed by scanning electron microscopy (SEM). The results indicated that xanthan and the hypochlorite-xanthan mixture reduced the corrosion rate of steel.

  6. Peptide interactions with steel surfaces: Inhibition of corrosion and calcium carbonate precipitation

    SciTech Connect

    Mueller, E.; Sikes, C.S. . Mineralization Center); Little, B.J. . Naval Research Lab.)

    1993-10-01

    Polyaspartate, a polyanionic peptide analog of an oyster-shell protein fraction, inhibited corrosion of AISI 1018 mild steel (UNS G10180) in seawater in a dose-dependent manner. A maximal inhibition of [approximately] 60% was obtained at a concentration of 100[mu]g mL[sup [minus]1]. Related peptides containing hydrophobic and/or phosphorylated amino acids had corrosion inhibition activities similar to or lower than polyaspartate in fresh and brackish waters. Binding studies demonstrated polyaspartate bound to mild steel in a dose- and time-dependent manner. Evidence for stainless steel (SS) binding was based on inhibition of calcium carbonate precipitation of the SS surface.

  7. Structure and Mechanical Properties of Maraging and Low-Carbon Martensitic Steels

    NASA Astrophysics Data System (ADS)

    Shvetsov, V. V.; Simonov, Yu. N.; Kleiner, L. M.

    2005-01-01

    The structure, mechanical properties, and crack resistance after tempering of maraging steel 03Kh11N10M2T (EP-678) and low-carbon martensitic steel 12Kh2G2NMFT are studied. The range of tempering temperatures ensuring the combination of properties required for massive parts (σr #x2265; 1300 MPa, σ0.2 ≥ 1100 MPa, KCT ≥ 0.2 MJ/m2) is determined. It is shown that steel 12Kh2G2NMFT is better adaptable to manufacture because it is hardened by air-cooling.

  8. Effects of LWR environments on fatigue life of carbon and low-alloy steels

    SciTech Connect

    Chopra, O.K.; Shack, W.J.

    1995-03-01

    SME Boiler and Pressure Vessel Code provides construction of nuclear power plant components. Figure I-90 Appendix I to Section III of the Code specifies fatigue design curves for structural materials. While effects of environments are not explicitly addressed by the design curves, test data suggest that the Code fatigue curves may not always be adequate in coolant environments. This paper reports the results of recent fatigue tests that examine the effects of steel type, strain rate, dissolved oxygen level, strain range, loading waveform, and surface morphology on the fatigue life of A 106-Gr B carbon steel and A533-Gr B low-alloy steel in water.

  9. X-ray photoelectron spectroscopy characterization of high dose carbon-implanted steel and titanium alloys

    NASA Astrophysics Data System (ADS)

    Viviente, J. L.; García, A.; Alonso, F.; Braceras, I.; Oñate, J. I.

    1999-04-01

    A study has been made of the depth dependence of the atomic fraction and chemical bonding states of AISI 440C martensitic stainless steel and Ti-6Al-4V alloy implanted with 75 keV C + at very high doses (above 10 18 ions cm -2), by means of X-ray photoelectron spectroscopy combined with an Ar + sputtering. A Gaussian-like carbon distribution was observed on both materials at the lowest implanted dose. More trapezoidal carbon depth-profiles were found with increasing implanted doses, and a pure carbon layer was observed only on the titanium alloy implanted at the highest dose. The implanted carbon was combined with both base metal and carbon itself to form metallic carbides and graphitic carbon. Furthermore, carbon-enriched carbides were also found by curve fitting the C 1s spectra. The titanium alloy showed a higher carbidic contribution than the steel implanted at the same C + doses. A critical carbon concentrations of about 33 at.% and 23 at.% were measured for the formation of C-C bonds in Ti-6Al-4V and steel samples, respectively. The carbon atoms were bound with metal to form carbidic compounds until these critical concentrations were reached; when this C concentration was exceeded the proportion of C-C bonds increased and resulted in the growth of carbonaceous layers.

  10. Effect of Carbon Contents and ti Addition on the Microstructure of Ultra-Low Carbon Steel

    NASA Astrophysics Data System (ADS)

    He, Yinsheng; Dong, Jiling; Lee, Changyu; Shin, Keesam; Yoon, Jeongbong; Lee, Byungho

    2011-06-01

    The microstructures of a series of ultra-low carbon (ULC) steels with various carbon contents (50-200ppm) and Ti addition (>500ppm) were studied by optical microscope (OM), scanning electron microscope (SEM) and transmission electron microscope (TEM). The specimens were fabricated under the process of hot rolling, cold rolling and a two-step continuous annealing. The experimental results showed that the increase of carbon content decreased grain size, whereas the addition of Ti resulted in a larger grain size compared to those without Ti addition. Dislocation (cell) structures were introduced by cold rolling, but it was removed by the two-step annealing. Only MnS precipitated from the Ti-free specimens. However, a larger amount of fine TiN, a few coarse TiS and the extremely low number of much coarser Ti3AlC were observed in the Ti-added specimens. Besides, the reduction of MnS inclusion was obtained by the addition of the Ti.

  11. 77 FR 264 - Certain Cut-To-Length Carbon-Quality Steel Plate From India, Indonesia, and the Republic of Korea...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-04

    ... ASTM A710 and A736 or their proprietary equivalents; (4) abrasion-resistant steels (i.e., USS AR 400... equivalents; (6) ball bearing steels; (7) tool steels; and (8) silicon manganese steel or silicon electric... International Trade Administration Certain Cut-To-Length Carbon-Quality Steel Plate From India, Indonesia,...

  12. 75 FR 75455 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil: Final Results of Full...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-03

    ... International Trade Administration Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil... certain hot-rolled flat-rolled carbon-quality steel products (hot-rolled steel) from Brazil, pursuant to.../COSIPA) \\2\\ and Companhia Siderurgica Nacional (CSN), producers of hot-rolled steel, and the Government...

  13. Use of Carbon Steel for Construction of Post-combustion CO 2 Capture Facilities: A Pilot-Scale Corrosion Study

    DOE PAGES

    Li, Wei; Landon, James; Irvin, Bradley; ...

    2017-04-13

    Corrosion studies were carried out on metal coated and noncoated carbon steel as well as stainless steel in a pilot-scale post-combustion CO2 capture process. Aqueous 30 wt % monoethanolamine (MEA) solvent was used without any chemical additive for antioxidation to examine a worst-case scenario where corrosion is not mitigated. The corrosion rate of all carbon steels was almost zero in the absorber column and CO2 lean amine piping except for Ni-coated carbon steel (<1.8 mm/yr). Ni2Al3/Al2O3 precoated carbon steels showed initial protection but lost their integrity in the stripping column and CO2 rich amine piping, and severe corrosion was eventuallymore » observed for all carbon steels at these two locations. Stainless steel was found to be stable and corrosion resistant in all of the sampling locations throughout the experiment. This study provides an initial framework for the use of carbon steel as a potential construction material for process units with relatively mild operating conditions (temperature less than 80 °C), such as the absorber and CO2 lean amine piping of a post-combustion CO2 capture process. As a result, it also warrants further investigation of using carbon steel with more effective corrosion mitigation strategies for process units where harsh environments are expected (such as temperatures greater than 100 °C).« less

  14. Microbial fouling and corrosion of carbon steel in deep anoxic alkaline groundwater.

    PubMed

    Rajala, Pauliina; Bomberg, Malin; Vepsäläinen, Mikko; Carpén, Leena

    2017-02-01

    Understanding the corrosion of carbon steel materials of low and intermediate level radioactive waste under repository conditions is crucial to ensure the safe storage of radioactive contaminated materials. The waste will be in contact with the concrete of repository silos and storage containers, and eventually with groundwater. In this study, the corrosion of carbon steel under repository conditions as well as the microbial community forming biofilm on the carbon steel samples, consisting of bacteria, archaea, and fungi, was studied over a period of three years in a groundwater environment with and without inserted concrete. The number of biofilm forming bacteria and archaea was 1,000-fold lower, with corrosion rates 620-times lower in the presence of concrete compared to the natural groundwater environment. However, localized corrosion was detected in the concrete-groundwater environment indicating the presence of local microenvironments where the conditions for pitting corrosion were favorable.

  15. Anodic Oxidation of Carbon Steel at High Current Densities and Investigation of Its Corrosion Behavior

    NASA Astrophysics Data System (ADS)

    Fattah-Alhosseini, Arash; Khan, Hamid Yazdani

    2017-02-01

    This work aims at studying the influence of high current densities on the anodization of carbon steel. Anodic protective coatings were prepared on carbon steel at current densities of 100, 125, and 150 A/dm2 followed by a final heat treatment. Coatings microstructures and morphologies were analyzed using X-ray diffraction (XRD) and scanning electron microscope (SEM). The corrosion resistance of the uncoated carbon steel substrate and the anodic coatings were evaluated in 3.5 wt pct NaCl solution through electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization measurements. The results showed that the anodic oxide coatings which were prepared at higher current densities had thicker coatings as a result of a higher anodic forming voltage. Therefore, the anodized coatings showed better anti-corrosion properties compared to those obtained at lower current densities and the base metal.

  16. RBS and GAXRD contributions to yttrium implanted extra low carbon steel characterization

    SciTech Connect

    Caudron, E.; Buscail, H.; Jacob, Y.P.; Stroosnijder, M.F.

    1999-02-01

    Extra low carbon steel samples were yttrium implanted using an ion implantation method. Composition and structural studies were carried out before and after yttrium implantations by several analytical and structural techniques (Rutherford backscattering spectrometry, reflection high energy electron diffraction, scanning electron microscopy, X-ray diffraction, and glancing angle X-ray diffraction) to characterize the yttrium implantation effect on extra low carbon steel. The aim of this article is to show the contributions of Rutherford back-scattering spectrometry (RBS) and glancing angle X-ray diffraction (GAXRD) to the determination of yttrium depth profiles in the samples. The results obtained by these techniques are compared to those of the other analyses performed in this work to show the existing correlation between composition and structural studies. Their results allow a better understanding of the effect of yttrium implantation in extra low carbon steel before studying their corrosion resistance at high temperature.

  17. Corrosion-resistant Foamed Cements for Carbon Steels

    SciTech Connect

    Sugama T.; Gill, S.; Pyatina, T., Muraca, A.; Keese, R.; Khan, A.; Bour, D.

    2012-12-01

    The cementitious material consisting of Secar #80, Class F fly ash, and sodium silicate designed as an alternative thermal-shock resistant cement for the Enhanced Geothermal System (EGS) wells was treated with cocamidopropyl dimethylamine oxide-based compound as foaming agent (FA) to prepare numerous air bubble-dispersed low density cement slurries of and #61603;1.3 g/cm3. Then, the foamed slurry was modified with acrylic emulsion (AE) as corrosion inhibitor. We detailed the positive effects of the acrylic polymer (AP) in this emulsion on the five different properties of the foamed cement: 1) The hydrothermal stability of the AP in 200 and #61616;C-autoclaved cements; 2) the hydrolysis-hydration reactions of the slurry at 85 and #61616;C; 3) the composition of crystalline phases assembled and the microstructure developed in autoclaved cements; 4) the mechanical behaviors of the autoclaved cements; and, 5) the corrosion mitigation of carbon steel (CS) by the polymer. For the first property, the hydrothermal-catalyzed acid-base interactions between the AP and cement resulted in Ca-or Na-complexed carboxylate derivatives, which led to the improvement of thermal stability of the AP. This interaction also stimulated the cement hydration reactions, enhancing the total heat evolved during cement’s curing. Addition of AP did not alter any of the crystalline phase compositions responsible for the strength of the cement. Furthermore, the AP-modified cement developed the porous microstructure with numerous defect-free cavities of disconnected voids. These effects together contributed to the improvement of compressive-strength and –toughness of the cured cement. AP modification of the cement also offered an improved protection of CS against brine-caused corrosion. There were three major factors governing the corrosion protection: 1) Reducing the extents of infiltration and transportation of corrosive electrolytes through the cement layer deposited on the underlying CS

  18. Torsional Failure of Carbon Fiber Composite Plates Versus Stainless Steel Plates for Comminuted Distal Fibula Fractures.

    PubMed

    Wilson, William K; Morris, Randal P; Ward, Adam J; Carayannopoulos, Nikoletta L; Panchbhavi, Vinod K

    2016-05-01

    Carbon fiber composite implants are gaining popularity in orthopedics, but with few independent studies of their failure characteristics under supra-physiologic loads. The objective of this cadaveric study was to compare torsional failure properties of bridge plating a comminuted distal fibula fracture with carbon fiber polyetheretherketone (PEEK) composite and stainless steel one-third tubular plates. Comminuted fractures were simulated in 12 matched pairs of fresh-frozen human fibulas with 2-mm osteotomies located 3 cm proximal to the tibiotalar joint. Each fibula pair was randomized for fixation and implanted with carbon fiber and stainless steel 5-hole one-third tubular plates. The constructs were loaded in external rotation at a rate of 1-degree/sec until failure with a materials testing system. Torsional stiffness and mode of failure, as well as displacement, torque, and energy absorption for the first instance of failure and peak failure, were determined. Statistical analysis was performed with paired t tests and chi-square. There were no significant differences among the 12 pairs for torsional stiffness, first failure torque, peak failure displacement, peak failure torque, or peak failure energy. Stainless steel plates exhibited significantly higher displacement (P < .001) and energy absorption (P = .001) at the first indication of failure than the carbon fiber plates. Stainless steel plates permanently deformed significantly more often than the carbon fiber plates (P = .035). Carbon fiber plates exhibited no plastic deformation with delamination of the composite, and brittle catastrophic failure in 1 specimen. In a comminuted human fibula fracture fixation model, carbon fiber implants exhibited multiple pre-peak failures at significantly lower angles than the first failure for the stainless steel implants, with some delamination of composite layers and brittle catastrophic failure rather than plastic deformation. The torsional failure properties of carbon

  19. Effect of carbon and nitrogen on grain boundary segregation in irradiated stainless steels

    NASA Astrophysics Data System (ADS)

    Kano, F.; Fukuya, K.; Hamada, S.; Miwa, Y.

    1998-10-01

    SUS304 stainless steels with carbon contents of 0.052%, 0.019% and 0.004% and SUS316L stainless steels with nitrogen contents of 0.095%, 0.032% and 0.003% were irradiated with 12 MeV Ni ions at 573 K to a dose of 1 dpa at 1 μm depth. Microstructure and grain boundary chemical composition were investigated using a transmission electron microscope with a field-emission-gun (FE-TEM) at the probe size of 0.5 nm. The number density of dislocation loop was higher as the carbon content was higher and was almost independent of nitrogen content. With increasing carbon and nitrogen content, the degree of Cr depletion and Si/Ni segregation was decreased. Both carbon and nitrogen suppressed the Cr depletion and Si/Ni segregation. The suppression effect of carbon was larger than that of nitrogen.

  20. Cathodic protection of steel reinforced concrete facilitated by using carbon fiber reinforced mortar or concrete

    SciTech Connect

    Hou, J.; Chung, D.D.L.

    1997-05-01

    Due to the decrease in volume electrical resistivity associated with carbon fiber addition (0.35 vol.%) to concrete (embedding steel rebar), concrete containing carbon fibers and silica fume reduced by 18% the driving voltage required for cathodic protection compared to plain concrete, and by 28% compared to concrete with silica fume. Due to the decrease in resistivity associated with carbon fiber addition (1.1 vol.%) to mortar, overlay (embedding titanium wires for electrical contacts to steel reinforced concrete) in the form of mortar containing carbon fibers and latex reduced by the 10% the driving voltage required for cathodic protection, compared to plain mortar overlay. In spite of the low resistivity of mortar overlay with carbon fibers, cathodic protection required multiple metal electrical contacts embedded in the mortar at a spacing of 11 cm or less.

  1. Characterization of Hydrogen-Related Fracture Behavior in As-Quenched Low-Carbon Martensitic Steel and Tempered Medium-Carbon Martensitic Steel

    NASA Astrophysics Data System (ADS)

    Shibata, Akinobu; Murata, Tamotsu; Takahashi, Hiroshi; Matsuoka, Takahiro; Tsuji, Nobuhiro

    2015-12-01

    Hydrogen-related fracture behaviors in low-carbon (Fe-0.1wtpctC) and medium-carbon (Fe-0.4wtpctC) martensitic steels were characterized through crystallographic orientation analysis using electron backscattering diffraction. The martensitic steels with lower strength (Fe-0.1C specimen or Fe-0.4C specimen tempered at higher temperature) exhibited transgranular fracture, where fractured surfaces consisted of dimples and quasi-cleavage patterns. Crystallographic orientation analysis revealed that several of the micro-cracks that formed around the prior austenite grain boundaries propagated along {011} planes. In contrast, fracture surface morphologies of the martensitic steels with higher strength (Fe-0.4C specimen tempered at lower temperature) appeared to be intergranular-like. Crystallographic orientation analysis demonstrated that, on a microscopic level, the fracture surfaces comprised the facets parallel to {011} planes. These results suggest that the hydrogen-related fractures in martensitic steels with higher strength are not exactly intergranular at the prior austenite grain boundaries, but they are transgranular fractures propagated along {011} planes close to the prior austenite grain boundaries. A description of the mechanism of hydrogen-related fracture is proposed based on the results.

  2. Direct gas-solid carbonation kinetics of steel slag and the contribution to in situ sequestration of flue gas CO(2) in steel-making plants.

    PubMed

    Tian, Sicong; Jiang, Jianguo; Chen, Xuejing; Yan, Feng; Li, Kaimin

    2013-12-01

    Direct gas-solid carbonation of steel slag under various operational conditions was investigated to determine the sequestration of the flue gas CO2 . X-ray diffraction analysis of steel slag revealed the existence of portlandite, which provided a maximum theoretical CO2 sequestration potential of 159.4 kg CO 2 tslag (-1) as calculated by the reference intensity ratio method. The carbonation reaction occurred through a fast kinetically controlled stage with an activation energy of 21.29 kJ mol(-1) , followed by 10(3) orders of magnitude slower diffusion-controlled stage with an activation energy of 49.54 kJ mol(-1) , which could be represented by a first-order reaction kinetic equation and the Ginstling equation, respectively. Temperature, CO2 concentration, and the presence of SO2 impacted on the carbonation conversion of steel slag through their direct and definite influence on the rate constants. Temperature was the most important factor influencing the direct gas-solid carbonation of steel slag in terms of both the carbonation conversion and reaction rate. CO2 concentration had a definite influence on the carbonation rate during the kinetically controlled stage, and the presence of SO2 at typical flue gas concentrations enhanced the direct gas-solid carbonation of steel slag. Carbonation conversions between 49.5 % and 55.5 % were achieved in a typical flue gas at 600 °C, with the maximum CO2 sequestration amount generating 88.5 kg CO 2 tslag (-1) . Direct gas-solid carbonation of steel slag showed a rapid CO2 sequestration rate, high CO2 sequestration amounts, low raw-material costs, and a large potential for waste heat utilization, which is promising for in situ carbon capture and sequestration in the steel industry.

  3. Super-strong dislocation-structured high-carbon martensite steel.

    PubMed

    Sun, Jun-Jie; Liu, Yong-Ning; Zhu, Yun-Tian; Lian, Fu-Liang; Liu, Hong-Ji; Jiang, Tao; Guo, Sheng-Wu; Liu, Wen-Qing; Ren, Xiao-Bing

    2017-07-26

    High-carbon martensite steels (with C > 0.5 wt.%) are very hard but at the same time as brittle as glass in as-quenched or low-temperature-tempered state. Such extreme brittleness, originating from a twin microstructure, has rendered these steels almost useless in martensite state. Therefore, for more than a century it has been a common knowledge that high-carbon martensitic steels are intrinsically brittle and thus are not expected to find any application in harsh loading conditions. Here we report that these brittle steels can be transformed into super-strong ones exhibiting a combination of ultrahigh strength and significant toughness, through a simple grain-refinement treatment, which refines the grain size to ~4 μm. As a result, an ultra-high tensile strength of 2.4~2.6 GPa, a significant elongation of 4~10% and a good fracture toughness (K1C) of 23.5~29.6 MPa m(1/2) were obtained in high-carbon martensitic steels with 0.61-0.65 wt.% C. These properties are comparable with those of "the king of super-high-strength steels"-maraging steels, but achieved at merely 1/30~1/50 of the price. The drastic enhancement in mechanical properties is found to arise from a transition from the conventional twin microstructure to a dislocation one by grain refinement. Our finding may provide a new route to manufacturing super-strong steels in a simple and economic way.

  4. Characterization of carbon ion implantation induced graded microstructure and phase transformation in stainless steel

    SciTech Connect

    Feng, Kai; Wang, Yibo; Li, Zhuguo; Chu, Paul K.

    2015-08-15

    Austenitic stainless steel 316L is ion implanted by carbon with implantation fluences of 1.2 × 10{sup 17} ions-cm{sup −} {sup 2}, 2.4 × 10{sup 17} ions-cm{sup −} {sup 2}, and 4.8 × 10{sup 17} ions-cm{sup −} {sup 2}. The ion implantation induced graded microstructure and phase transformation in stainless steel is investigated by X-ray diffraction, X-ray photoelectron spectroscopy and high resolution transmission electron microscopy. The corrosion resistance is evaluated by potentiodynamic test. It is found that the initial phase is austenite with a small amount of ferrite. After low fluence carbon ion implantation, an amorphous layer and ferrite phase enriched region underneath are formed. Nanophase particles precipitate from the amorphous layer due to energy minimization and irradiation at larger ion implantation fluence. The morphology of the precipitated nanophase particles changes from circular to dumbbell-like with increasing implantation fluence. The corrosion resistance of stainless steel is enhanced by the formation of amorphous layer and graphitic solid state carbon after carbon ion implantation. - Highlights: • Carbon implantation leads to phase transformation from austenite to ferrite. • The passive film on SS316L becomes thinner after carbon ion implantation. • An amorphous layer is formed by carbon ion implantation. • Nanophase precipitate from amorphous layer at higher ion implantation fluence. • Corrosion resistance of SS316L is improved by carbon implantation.

  5. Changes in the structure and properties of low-carbon low-alloy pipe steels upon inoculation with REM

    NASA Astrophysics Data System (ADS)

    Denisova, T. V.; Vyboishchik, M. A.; Tetyueva, T. V.; Ioffe, A. V.

    2013-01-01

    The influence of REM additives on the structure, mechanical properties and corrosion resistance of low-carbon low-alloy steels is studied. The effect of inoculation with rare-earth metals on the content of sulfur and oxygen in the steels and on the degree of their contamination with nonmetallic inclusions are investigated. The resistance of the steels to stress sulfide corrosion cracking, hydrogen cracking and total, local, carbon dioxide and bacterial corrosion is determined.

  6. 76 FR 4291 - Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Partial Rescission of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-25

    ... International Trade Administration Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea... administrative review of the countervailing duty order on corrosion- resistant carbon steel flat products from... ] requests for administrative review and partial revocation of the countervailing duty order on...

  7. 76 FR 69703 - Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Notice of Extension of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-09

    ... International Trade Administration Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea...) published a notice of initiation of the administrative review of the antidumping duty order on corrosion... results of this review. See Certain Corrosion-Resistant Carbon Steel Flat Products From the Republic...

  8. 75 FR 77615 - Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Notice of Extension of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-13

    ... International Trade Administration Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea...) published a notice of initiation of the administrative review of the antidumping duty order on corrosion... results of this review. See Certain Corrosion-Resistant Carbon Steel Flat Products From the Republic...

  9. 78 FR 19210 - Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Final Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-29

    ... International Trade Administration Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea...) has completed its administrative review of the countervailing duty (CVD) order on corrosion-resistant...\\ See Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Preliminary Results...

  10. 76 FR 80963 - Cut-To-Length Carbon-Quality Steel Plate From India, Indonesia, Italy, Japan, and Korea

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-27

    ... COMMISSION Cut-To-Length Carbon-Quality Steel Plate From India, Indonesia, Italy, Japan, and Korea...-length carbon-quality steel plate from Japan would not be likely to lead to continuation or recurrence of... and Commissioner Pinkert dissenting with respect to Japan. Background The Commission instituted these...

  11. 76 FR 5205 - Carbon Steel Butt-Weld Pipe Fittings from Brazil, China, Japan, Taiwan, and Thailand

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-28

    ... COMMISSION Carbon Steel Butt-Weld Pipe Fittings from Brazil, China, Japan, Taiwan, and Thailand AGENCY... concerning the antidumping duty orders on carbon steel butt-weld pipe fittings from Brazil, China, Japan..., China, Japan, Taiwan, and Thailand would be likely to lead to continuation or recurrence of material...

  12. 77 FR 301 - Corrosion-Resistant Carbon Steel Flat Products From Germany and Korea: Institution of Five-Year...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-04

    ... Reviews Concerning the Countervailing Duty Order on Corrosion-Resistant Carbon Steel Flat Products From Korea and the Antidumping Duty Orders on Corrosion-Resistant Carbon Steel Flat Products From Germany and... (19 U.S.C. 1675(c)) (the Act) to determine whether revocation of the countervailing duty order on...

  13. 77 FR 25141 - Corrosion-Resistant Carbon Steel Flat Products From Germany and South Korea: Extension of Time...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-27

    ... International Trade Administration Corrosion-Resistant Carbon Steel Flat Products From Germany and South Korea... Germany and South Korea (Korea), pursuant to section 751(c) of the Tariff Act of 1930, as amended (the Act...-Resistant Carbon Steel Flat Products from Germany and South Korea: Adequacy Redetermination...

  14. 76 FR 56395 - Certain Welded Carbon Steel Pipe and Tube From Turkey: Notice of Extension of Time Limit for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-13

    ... International Trade Administration Certain Welded Carbon Steel Pipe and Tube From Turkey: Notice of Extension of... and tube from Turkey for the period May 1, 2009, through April 30, 2010. See Certain Welded Carbon Steel Pipe and Tube From Turkey; Notice of Preliminary Results of Antidumping Duty Administrative...

  15. 76 FR 3612 - Circular Welded Carbon Steel Pipes and Tubes From Taiwan; Extension of Time Limit for Preliminary...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-20

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE International Trade Administration Circular Welded Carbon Steel Pipes and Tubes From Taiwan; Extension of Time... rescinding the review with respect to Yieh Hsing. See Circular Welded Carbon Steel Pipes and Tubes...

  16. 76 FR 71938 - Circular Welded Carbon Steel Pipes and Tubes From Thailand: Extension of Time Limit for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-21

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE International Trade Administration Circular Welded Carbon Steel Pipes and Tubes From Thailand: Extension of Time... the antidumping duty order on circular welded carbon steel pipes and tubes from Thailand for...

  17. 78 FR 79665 - Welded Carbon Steel Standard Pipe and Tube Products From Turkey: Final Results of Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-31

    ... Carbon Steel Standard Pipe and Tube Products From Turkey: Final Results of Antidumping Duty... order on welded carbon steel standard pipe and tube products (welded pipe and tube) from Turkey.\\1\\ The... Tube Products from Turkey: Preliminary Results of Antidumping Duty Administrative Review; 2011-2012,...

  18. 78 FR 286 - Circular Welded Carbon Steel Pipes and Tubes From Turkey; Amended Final Results of Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-03

    ... Welded Carbon Steel Pipes and Tubes From Turkey; Amended Final Results of Antidumping Duty Administrative... and tubes from Turkey for the period of review (POR) May 1, 2010, through April 30, 2011.\\1\\ We are..., as amended (the Act). \\1\\ See Circular Welded Carbon Steel Pipes and Tubes from Turkey; Final...

  19. 75 FR 1495 - Certain Hot-Rolled Carbon Steel Flat Products From India: Preliminary Results of Countervailing...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-11

    ... governments of Gujarat, Maharashtra, Andhra Pradesh, Chhattisgarh and Karnataka. On July 30, 2009, the... Review: Certain Cut-to-Length Carbon-Quality Steel Plate from the Republic of Korea, 71 FR 38861 (July 10..., 2008) (Preliminary Results of Fourth HRS Review) and Certain Hot-Rolled Carbon Steel Flat Products From...

  20. 77 FR 36256 - Circular Welded Carbon-Quality Steel Pipe From India: Postponement of Final Determination of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-06-18

    ... International Trade Administration Circular Welded Carbon-Quality Steel Pipe From India: Postponement of Final... investigation on circular welded carbon- quality steel pipe from India.\\1\\ On June 1, 2012, the Department... antidumping duty investigation is currently due on August 6, 2012. \\1\\ See Circular Welded...

  1. 76 FR 78612 - Certain Welded Carbon Steel Standard Pipes and Tubes From India: Rescission of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-19

    ... International Trade Administration Certain Welded Carbon Steel Standard Pipes and Tubes From India: Rescission... certain welded carbon steel standard pipes and tubes from India. The period of review is May 1, 2010... notice of initiation of an administrative review of the antidumping duty order on certain welded...

  2. 76 FR 48143 - Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of China: Preliminary...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-08

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of... administrative review of the antidumping duty order on certain hot- rolled carbon steel flat products (``hot... published the antidumping duty order on hot-rolled from the PRC. See Notice of the Antidumping Duty Order...

  3. 76 FR 2344 - Certain Hot-Rolled Carbon Steel Flat Products From India: Notice of Preliminary Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-13

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From India: Notice of... order on certain hot-rolled carbon steel flat products from India (``Indian Hot-Rolled'') manufactured... December 3, 2001, the Department published in the Federal Register the antidumping duty order on Indian Hot...

  4. 76 FR 4633 - Carbon Steel Butt-Weld Pipe Fittings From the People's Republic of China: Notice of Court...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-26

    ... International Trade Administration Carbon Steel Butt-Weld Pipe Fittings From the People's Republic of China... scope of the Order \\1\\ as excluding carbon steel butt-weld pipe fittings from the People's Republic of.... LLC, d/b/a King Architectural Metals v. United States, Slip Op. 10-111, Court No. 09-00477...

  5. 78 FR 73827 - Suspension Agreement on Certain Cut-to-Length Carbon Steel Plate From the Russian Federation...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-09

    ... International Trade Administration Suspension Agreement on Certain Cut-to-Length Carbon Steel Plate From the... of an administrative review of the suspension agreement on certain cut-to-length carbon steel plate from the Russian Federation covering Joint Stock Company Severstal (Severstal). See Certain...

  6. 76 FR 22725 - Cut-to-Length Carbon Steel Plate From India, Indonesia, Italy, Japan, and Korea; Scheduling of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-22

    ... COMMISSION Cut-to-Length Carbon Steel Plate From India, Indonesia, Italy, Japan, and Korea; Scheduling of Full Five-Year Reviews Concerning the Countervailing Duty Orders and Antidumping Duty Orders on Cut-to...) to determine whether revocation of the countervailing duty orders on cut-to-length carbon steel...

  7. 78 FR 29113 - Certain Cut-to-Length Carbon-Quality Steel Plate Products From the Republic of Korea: Final...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-17

    ... International Trade Administration Certain Cut-to-Length Carbon-Quality Steel Plate Products From the Republic... order on certain cut-to-length carbon-quality steel plate products from the Republic of Korea. For these... preliminary results of the administrative review of the antidumping duty order on certain cut-to-length...

  8. 77 FR 47593 - Certain Cut-to-Length Carbon Steel Plate From the People's Republic of China: Preliminary Results...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-09

    ... International Trade Administration Certain Cut-to-Length Carbon Steel Plate From the People's Republic of China... review of the antidumping duty order on certain cut-to- length carbon steel plate (``CTL plate'') from... to request an administrative review of the antidumping duty order on CTL plate from the PRC.\\2\\ On...

  9. 76 FR 34044 - Carbon and Certain Alloy Steel Wire Rod From Mexico: Extension of Time Limits for the Preliminary...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-10

    ... From the Federal Register Online via the Government Publishing Office ] DEPARTMENT OF COMMERCE International Trade Administration Carbon and Certain Alloy Steel Wire Rod From Mexico: Extension of Time Limits... administrative review of the antidumping duty order on carbon and certain alloy steel wire rod from...

  10. 75 FR 55742 - Certain Hot-Rolled Carbon Steel Flat Products from India: Extension of Time Limit for Preliminary...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-14

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products from India: Extension of Time... antidumping duty administrative review of certain hot- rolled carbon steel flat products from India for...

  11. 76 FR 26694 - Certain Hot-Rolled Carbon Steel Flat Products From India: Final Rescission of Countervailing Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-09

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From India: Final Rescission of... countervailing duty (CVD) order on certain hot-rolled carbon steel flat products from India. See Antidumping or... review with respect to Ispat, and provided interested parties with 20 days to comment. See Certain...

  12. 76 FR 3083 - Certain Welded Carbon Steel Pipe and Tube From Turkey: Extension of Time Limit for Preliminary...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-19

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE International Trade Administration Certain Welded Carbon Steel Pipe and Tube From Turkey: Extension of Time... administrative review of the antidumping duty order on certain welded carbon steel pipe and tube from Turkey...

  13. 76 FR 76939 - Certain Welded Carbon Steel Pipe and Tube From Turkey: Notice of Final Results of Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-09

    ... or cold-rolled mechanical tubing, pipe and tube hollows for redraws, finished scaffolding, and... International Trade Administration Certain Welded Carbon Steel Pipe and Tube From Turkey: Notice of Final... welded carbon steel pipe and tube from Turkey. The administrative review covers the Borusan Group \\1\\...

  14. 78 FR 72863 - Circular Welded Carbon Quality Steel Pipe From the People's Republic of China: Continuation of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-04

    ... International Trade Administration Circular Welded Carbon Quality Steel Pipe From the People's Republic of China... carbon quality steel pipe (circular welded pipe) from the People's Republic of China (PRC) would likely... circular welded pipe from the PRC pursuant to section 751(c) of the Tariff Act of 1930, as amended (the Act...

  15. 78 FR 72863 - Circular Welded Carbon-Quality Steel Pipe From the People's Republic of China: Continuation of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-04

    ... International Trade Administration Circular Welded Carbon-Quality Steel Pipe From the People's Republic of China... revocation of the antidumping duty order on circular welded carbon-quality steel pipe (``circular welded pipe... circular welded pipe from the PRC, pursuant to section 751(c) of the Tariff Act of 1930, as amended (the...

  16. 76 FR 21331 - Certain Carbon Steel Butt-Weld Pipe Fittings From Brazil, Japan, Taiwan, Thailand, and the People...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-15

    ... order consists of certain carbon steel butt-weld type fittings, other than couplings, under 14 inches in... consists of certain carbon steel butt-weld type fittings, other than couplings, under 14 inches in inside...-weld type fittings, other than couplings, under 14 inches in inside diameter, whether finished...

  17. Austenite grain growth kinetics in Al-killed plain carbon steels

    NASA Astrophysics Data System (ADS)

    Militzer, Matthias; Hawbolt, E. Bruce; Ray Meadowcroft, T.; Giumelli, Alan

    1996-11-01

    Austenite grain growth kinetics have been investigated in three Al-killed plain carbon steels. Experimental results have been validated using the statistical grain growth model by Abbruzzese and Lücke, which takes pinning by second-phase particles into account. It is shown that the pinning force is a function of the pre-heat-treatment schedule. Extrapolation to the conditions of a hot-strip mill indicates that grain growth occurs without pinning during conventional processing. Analytical relations are proposed to simulate austenite grain growth for Al-killed plain carbon steels for any thermal path in a hot-strip mill.

  18. Structure and mechanical properties of hot-deformed low-carbon martensitic steel

    NASA Astrophysics Data System (ADS)

    Romanov, I. D.; Shatsov, A. A.; Zakirova, M. G.; Berezin, S. K.

    2016-03-01

    The structural changes in low-carbon martensitic 15Kh2G2NMFBA steel induced by its hot forging in the temperature range 1150-850°C have been studied. The calculated cracking resistance parameter I c is in agreement with its experimental value. A relation is found between the lath sizes in the martensite structure and the change in the impact toughness characteristics. A combined regime of hot deformation and hot treatment of the low-carbon martensitic steel is proposed to form submicrometer-sized structural elements and high strength and impact toughness characteristics.

  19. A discussion for stabilization time of carbon steel in atmospheric corrosion

    NASA Astrophysics Data System (ADS)

    Zhang, Zong-kai; Ma, Xiao-bing; Cai, Yi-kun

    2017-09-01

    Stabilization time is an important parameter in long-term prediction of carbon steel corrosion in atmosphere. The range of the stabilization time of carbon steel in atmospheric corrosion has been published in many scientific literatures. However, the results may not precise because engineering experiences is dominant. This paper deals with the recalculation of stabilization time based on ISO CORRAG program, and analyzes the results and makes a comparison to the data mentioned above. In addition, a new thinking to obtain stabilization time will be proposed.

  20. Image analysis of corrosion pit initiation on ASTM type A240 stainless steel and ASTM type A 1008 carbon steel

    NASA Astrophysics Data System (ADS)

    Nine, H. M. Zulker

    The adversity of metallic corrosion is of growing concern to industrial engineers and scientists. Corrosion attacks metal surface and causes structural as well as direct and indirect economic losses. Multiple corrosion monitoring tools are available although those are time-consuming and costly. Due to the availability of image capturing devices in today's world, image based corrosion control technique is a unique innovation. By setting up stainless steel SS 304 and low carbon steel QD 1008 panels in distilled water, half-saturated sodium chloride and saturated sodium chloride solutions and subsequent RGB image analysis in Matlab, in this research, a simple and cost-effective corrosion measurement tool has identified and investigated. Additionally, the open circuit potential and electrochemical impedance spectroscopy results have been compared with RGB analysis to gratify the corrosion. Additionally, to understand the importance of ambiguity in crisis communication, the communication process between Union Carbide and Indian Government regarding the Bhopal incident in 1984 was analyzed.

  1. Tensile property improvement of TWIP-cored three-layer steel sheets fabricated by hot-roll-bonding with low-carbon steel or interstitial-free steel

    PubMed Central

    Park, Jaeyeong; Kim, Jung-Su; Kang, Minju; Sohn, Seok Su; Cho, Won Tae; Kim, Hyoung Seop; Lee, Sunghak

    2017-01-01

    TWIP-cored three-layer steel sheets were newly fabricated by hot rolling of TWIP steel sheet surrounded by low-carbon (LC) or interstitial-free (IF) steel sheets. TWIP/LC or TWIP/IF interfaces were well bonded without pores or voids, while a few pearlites were thinly formed along the interfaces. The strengths and elongation of the TWIP-cored sheets increased as the volume fraction of TWIP-cored region increased, and were also well matched with the ones calculated by a rule of mixtures based on volume fraction or force fraction. According to digital image correlation and electron back-scatter diffraction analyses, very high strain hardening effect in the initial deformation stage and active twin formation in the interfacial region beneficially affected the overall homogeneous deformation in the TWIP-cored sheets without any yield point phenomenon occurring in the LC sheet and serrations occurring in the TWIP sheet, respectively. These TWIP-cored sheets can cover a wide range of yield strength, tensile strength, and ductility levels, e.g., 320~498 MPa, 545~878 MPa, and 48~54%, respectively, by controlling the volume fraction of TWIP-cored region, and thus present new applications to multi-functional automotive steel sheets requiring excellent properties. PMID:28067318

  2. Tensile property improvement of TWIP-cored three-layer steel sheets fabricated by hot-roll-bonding with low-carbon steel or interstitial-free steel.

    PubMed

    Park, Jaeyeong; Kim, Jung-Su; Kang, Minju; Sohn, Seok Su; Cho, Won Tae; Kim, Hyoung Seop; Lee, Sunghak

    2017-01-09

    TWIP-cored three-layer steel sheets were newly fabricated by hot rolling of TWIP steel sheet surrounded by low-carbon (LC) or interstitial-free (IF) steel sheets. TWIP/LC or TWIP/IF interfaces were well bonded without pores or voids, while a few pearlites were thinly formed along the interfaces. The strengths and elongation of the TWIP-cored sheets increased as the volume fraction of TWIP-cored region increased, and were also well matched with the ones calculated by a rule of mixtures based on volume fraction or force fraction. According to digital image correlation and electron back-scatter diffraction analyses, very high strain hardening effect in the initial deformation stage and active twin formation in the interfacial region beneficially affected the overall homogeneous deformation in the TWIP-cored sheets without any yield point phenomenon occurring in the LC sheet and serrations occurring in the TWIP sheet, respectively. These TWIP-cored sheets can cover a wide range of yield strength, tensile strength, and ductility levels, e.g., 320~498 MPa, 545~878 MPa, and 48~54%, respectively, by controlling the volume fraction of TWIP-cored region, and thus present new applications to multi-functional automotive steel sheets requiring excellent properties.

  3. Tensile property improvement of TWIP-cored three-layer steel sheets fabricated by hot-roll-bonding with low-carbon steel or interstitial-free steel

    NASA Astrophysics Data System (ADS)

    Park, Jaeyeong; Kim, Jung-Su; Kang, Minju; Sohn, Seok Su; Cho, Won Tae; Kim, Hyoung Seop; Lee, Sunghak

    2017-01-01

    TWIP-cored three-layer steel sheets were newly fabricated by hot rolling of TWIP steel sheet surrounded by low-carbon (LC) or interstitial-free (IF) steel sheets. TWIP/LC or TWIP/IF interfaces were well bonded without pores or voids, while a few pearlites were thinly formed along the interfaces. The strengths and elongation of the TWIP-cored sheets increased as the volume fraction of TWIP-cored region increased, and were also well matched with the ones calculated by a rule of mixtures based on volume fraction or force fraction. According to digital image correlation and electron back-scatter diffraction analyses, very high strain hardening effect in the initial deformation stage and active twin formation in the interfacial region beneficially affected the overall homogeneous deformation in the TWIP-cored sheets without any yield point phenomenon occurring in the LC sheet and serrations occurring in the TWIP sheet, respectively. These TWIP-cored sheets can cover a wide range of yield strength, tensile strength, and ductility levels, e.g., 320~498 MPa, 545~878 MPa, and 48~54%, respectively, by controlling the volume fraction of TWIP-cored region, and thus present new applications to multi-functional automotive steel sheets requiring excellent properties.

  4. Factors affecting stress assisted corrosion cracking of carbon steel under industrial boiler conditions

    NASA Astrophysics Data System (ADS)

    Yang, Dong

    Failure of carbon steel boiler tubes from waterside has been reported in the utility boilers and industrial boilers for a long time. In industrial boilers, most waterside tube cracks are found near heavy attachment welds on the outer surface and are typically blunt, with multiple bulbous features indicating a discontinuous growth. These types of tube failures are typically referred to as stress assisted corrosion (SAC). For recovery boilers in the pulp and paper industry, these failures are particularly important as any water leak inside the furnace can potentially lead to smelt-water explosion. Metal properties, environmental variables, and stress conditions are the major factors influencing SAC crack initation and propagation in carbon steel boiler tubes. Slow strain rate tests (SSRT) were conducted under boiler water conditions to study the effect of temperature, oxygen level, and stress conditions on crack initation and propagation on SA-210 carbon steel samples machined out of boiler tubes. Heat treatments were also performed to develop various grain size and carbon content on carbon steel samples, and SSRTs were conducted on these samples to examine the effect of microstructure features on SAC cracking. Mechanisms of SAC crack initation and propagation were proposed and validated based on interrupted slow strain tests (ISSRT). Water chemistry guidelines are provided to prevent SAC and fracture mechanics model is developed to predict SAC failure on industrial boiler tubes.

  5. Does carbonation of steel slag particles reduce their toxicity? An in vitro approach.

    PubMed

    Ibouraadaten, Saloua; van den Brule, Sybille; Lison, Dominique

    2015-06-01

    Mineral carbonation can stabilize industrial residues and, in the steel industry, may contribute to simultaneously valorize CO2 emissions and slag. We hypothesized that, by restricting the leaching of metals of toxicological concern such as Cr and V, carbonation can suppress the toxicity of these materials. The cytotoxic activity (WST1 assay) of slag dusts collected from a stainless and a Linz-Donawitz (LD) steel plant, before and after carbonation, was examined in J774 macrophages. The release of Cr, V, Fe, Mn and Ni was measured after incubation in artificial lung fluids mimicking the extracellular and phagolysosomal milieu to which particles are confronted after inhalation. LD slag had the higher Fe, Mn and V content, and was more cytotoxic than stainless steel slag. The cytotoxic activity of LD but not of stainless dusts was reduced after carbonation. The cytotoxic activity of the dusts toward J774 macrophages necessitated a direct contact with the cells and was reduced in the presence of inhibitors of phagocytosis (cytochalasin D) or phagolysosome acidification (bafilomycin), pointing to a key role of metallic constituents released in phagolysosomes. This in vitro study supports a limited reduction of the cytotoxic activity of LD, but not of stainless, steel dusts upon carbonation.

  6. Tribological performance of hard carbon coatings on 440C bearing steel

    NASA Astrophysics Data System (ADS)

    Kustas, Frank N.; Misra, Mohan S.; Shepard, Donald F.; Froechtenigt, Joseph F.

    1990-12-01

    Hard carbon coating such as diamond and diamond-like c :bon (also referred to as amorphous carbon) have received considerable attention for tribological applications due to their high hardness high modulus and desirable surface properties. Unfortunately most of the deposition techniques induce high substrate temperatures that temper traditional bearing steels and reduce the substrate load-carrying capability. Therefore to effectively use these desirable coatings a lower temperature deposition technique is required. Ion beam deposition offers essentially ambient temperature conditions accurate control ofprocess parameters and good coating-substrate adhesion. To use these attributes a test program was initiated to deposit mass analyzed high purity carbon and methane ions onto molybdenum and 440C bearing steel for subsequent characterization by Raman spectroscopy and friction-wear tests. Preliminary results for a coating deposited from a CO source showed an amorphous carbon/microcrystalline graphite structure which exhibited very high microhardness and a 3-fold reduction in coefficient of friction for unlubricated tests compared to untreated 440C steel. In addition incrementally increasing the applied load up to a factor of 5 resulted in progressively lower coefficients of friction only a minor increase (about 11) in the wear scar depth and no dramatic coating delamination or damage. Therefore an amorphous carbon/graphite coating applied to 440C steel at ambient temperature exhibits solid lubricating film characteristics with extremely high load-carrying capability. *Work performed under Martin Marietta Independent Research and Development Project D-8 1R Materials Technology. 116

  7. Microstructure and Mechanical Properties of Resistance Spot Welding Joints of Carbonitrided Low-Carbon Steels

    NASA Astrophysics Data System (ADS)

    Taweejun, Nipon; Poapongsakorn, Piyamon; Kanchanomai, Chaosuan

    2017-04-01

    Carbonitrided low-carbon steels are resistance welded in various engineering components. However, there are no reports on the microstructure and mechanical properties of their resistance spot welding (RSW) joints. Therefore, various carbonitridings were performed on the low-carbon steel sheets, and then various RSWs were applied to these carbonitrided sheets. The metallurgical and mechanical properties of the welding joint were investigated and discussed. The peak load and failure energy increased with the increases of welding current and fusion zone (FZ) size. At 11 kA welding current, the carbonitrided steel joint had the failure energy of 16 J, i.e., approximately 84 pct of untreated steel joint. FZ of carbonitrided steel joint consisted of ferrite, Widmanstatten ferrite, and untempered martensite, i.e., the solid-state transformation products, while the microstructure at the outer surfaces consisted of untempered martensite and retained austenite. The surface hardening of carbonitrided steel after RSW could be maintained, i.e., approximately 810 HV. The results can be applied to carbonitriding and RSW to achieve a good welding joint.

  8. 75 FR 2107 - Certain Cut-to-Length Carbon-Quality Steel Plate from the Republic of Korea: Extension of the...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-14

    ... International Trade Administration Certain Cut-to-Length Carbon-Quality Steel Plate from the Republic of Korea... duty order on certain cut-to-length carbon-quality steel plate from the Republic of Korea and intent to rescind the administrative review in part. See Certain Cut-to-Length Carbon-Quality Steel Plate From...

  9. 75 FR 77828 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil: Extension of Time Limit...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-14

    ... International Trade Administration Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil...-rolled flat-rolled carbon- quality steel products from Brazil for the period January 1, 2008, through December 31, 2008. See Certain Hot-Rolled Flat-Rolled Carbon Quality Steel Products From Brazil...

  10. 75 FR 32160 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products from Brazil: Extension of Time Limit...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-07

    ... International Trade Administration Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products from Brazil... certain hot-rolled flat- rolled carbon-quality steel products from Brazil. See Agreement Suspending the... review of the countervailing duty order on certain hot-rolled flat-rolled carbon-quality steel products...

  11. Effect of submicrocrystalline state on strength and impact toughness of low-carbon 12GBA steel

    NASA Astrophysics Data System (ADS)

    Safarov, I. M.; Korznikov, A. V.; Sergeev, S. N.; Gladkovskii, S. V.; Borodin, E. M.

    2012-10-01

    The effect of intense warm deformation on the structure and mechanical properties of low-carbon 12GBA steel was investigated. A submicrocrystalline (SMC) structure with an average element size of 0.3 μm was formed in the steel by isothermal overall forging. The formation of the SMC structure resulted in a sharp increase in strength by a factor of two to three in relation to the initial coarse-grained state while retaining a sufficient level of plasticity and impact toughness. After further annealing, steels exhibit an improved set of properties; i.e., as the strength decreases slightly, the plasticity increases sharply. Impact tests at low temperatures have shown the significant advantage of the SMC state of the steel over the coarse-grained state in the impact toughness. It is established that the cold resistance in the SMC state increases because the crack propagation prevails in the overall sample fracture.

  12. Atomic migration of carbon in hard turned layers of carburized bearing steel

    SciTech Connect

    Bedekar, Vikram; Poplawsky, Jonathan D.; Guo, Wei; Shivpuri, Rajiv; Scott Hyde, R.

    2016-01-01

    In grain finement and non-equilibrium there is carbon segregation within grain boundaries alters the mechanical performance of hard turning layers in carburized bearing steel. Moreover, an atom probe tomography (APT) study on the nanostructured hard turning layers reveals carbon migration to grain boundaries as a result of carbide decomposition during severe plastic deformation. In addition, samples exposed to different cutting speeds show that the carbon migration rate increases with the cutting speed. For these two effects lead to an ultrafine carbon network structure resulting in increased hardness and thermal stability in the severely deformed surface layer.

  13. Atomic migration of carbon in hard turned layers of carburized bearing steel

    DOE PAGES

    Bedekar, Vikram; Poplawsky, Jonathan D.; Guo, Wei; ...

    2016-01-01

    In grain finement and non-equilibrium there is carbon segregation within grain boundaries alters the mechanical performance of hard turning layers in carburized bearing steel. Moreover, an atom probe tomography (APT) study on the nanostructured hard turning layers reveals carbon migration to grain boundaries as a result of carbide decomposition during severe plastic deformation. In addition, samples exposed to different cutting speeds show that the carbon migration rate increases with the cutting speed. For these two effects lead to an ultrafine carbon network structure resulting in increased hardness and thermal stability in the severely deformed surface layer.

  14. Corrosion effects of hydrogen sulfide on coiled tubing and carbon steel in hydrochloric acid

    SciTech Connect

    1997-09-01

    Coiled tubing is commonly used in oilwell drilling and stimulation. It has been reported to be less susceptible to acid attack than carbon steel in acidizing. Corrosion problems are frequently reported from field activities and include corrosion/erosion, galvanic attack, brine/oxygen/acid attack, and HCl/H{sub 2}S attack. In this study, coiled tubing was exposed to inhibited HCl acid in the presence and absence of H{sub 2}S. Four HCl inhibitors and one H{sub 2}S inhibitor were evaluated, and the corrosion rates of coiled tubing, carbon steel (J-55), and carburized steel were compared. Tests were conducted at atmospheric pressure for temperatures less than and equal to 200 F. At temperatures greater than 200 F; tests were conducted at 4,000 psi.

  15. Evolution of Initial Atmospheric Corrosion of Carbon Steel in an Industrial Atmosphere

    NASA Astrophysics Data System (ADS)

    Pan, Chen; Han, Wei; Wang, Zhenyao; Wang, Chuan; Yu, Guocai

    2016-12-01

    The evolution of initial corrosion of carbon steel exposed to an industrial atmosphere in Shenyang, China, has been investigated by gravimetric, XRD, SEM/EDS and electrochemical techniques. The kinetics of the corrosion process including the acceleration and deceleration processes followed the empirical equation D = At n . The rust formed on the steel surface was bi-layered, comprised of an inner and outer layer. The outer layer was formed within the first 245 days and had lower iron content compared to the inner layer. However, the outer layer disappeared after 307 days of exposure, which is considered to be associated with the depletion of Fe3O4. The evolution of the rust layer formed on the carbon steel has also been discussed.

  16. Carbonated aqueous media for quench heat treatment of steels

    NASA Astrophysics Data System (ADS)

    Nayak, U. Vignesh; Rao, K. M. Pranesh; Pai, M. Ashwin; Prabhu, K. Narayan

    2016-09-01

    Distilled water and polyalkylene glycol (PAG)-based aqueous quenchants of 5 and 10 vol.% with and without carbonation were prepared and used as heat transfer media during immersion quenching. Cooling curves were recorded during quenching of an inconel 600 cylindrical probe instrumented with multiple thermocouples. It was observed that the vapor stage duration was prolonged and the wetting front ascended uniformly for quenching with carbonated media. The cooling data were analyzed by determining the critical cooling parameters and by estimating the spatially dependent probe/quenchant interfacial heat flux transients. The study showed significantly reduced values of heat transfer rate for carbonated quenchants compared to quenchants without carbonation. Further, the reduction was more pronounced in the case of PAG-based carbonated quenchants than carbonated distilled water. The results also showed the dependence of heat transfer characteristics of the carbonated media on polymer concentration. The effect of quench uniformity on the microstructure of the material was assessed.

  17. The influence of aluminum and carbon on the abrasion resistance of high manganese steels

    NASA Astrophysics Data System (ADS)

    Buckholz, Samuel August

    Abrasive wear testing of lightweight, austenitic Fe-Mn-Al-C cast steel has been performed in accordance with ASTM G65 using a dry sand, rubber wheel, abrasion testing apparatus. Testing was conducted on a series of Fe-30Mn-XAl-YC-1Si-0.5Mo chemistries containing aluminum levels from 2.9 to 9.5 wt.% and carbon levels from 0.9 to 1.83 wt.%. Solution treated materials having an austenitic microstructure produced the highest wear resistance. Wear resistance decreased with higher aluminum, lower carbon, and higher hardness after age hardening. In the solution treated condition the wear rate was a strong function of the aluminum to carbon ratio and the wear rate increased with a parabolic dependence on the Al/C ratio, which ranged from 1.8 to 10.2. Examination of the surface wear scar revealed a mechanism of plowing during abrasion testing and this method of material removal is sensitive to work hardening rate. Work hardening behavior was determined from tensile tests and also decreased with increasing Al/C ratio and after aging hardening. The loss of wear resistance is related to short range ordering of Al and C in the solution treated materials and kappa-carbide precipitation in age hardened materials and both contribute to planar slip and lower work hardening rates. A high carbon tool steel (W1) and a bainitic low alloy steel (SAE 8620) were also tested for comparison. A lightweight steel containing 6.5 wt.% Al and 1.2 wt.% C has wear resistance comparable to within 5% of the bainitic SAE 8620 steel forging currently used for the Bradley Fighting Vehicle track shoe and this cast Fe-Mn-Al-C steel, at equivalent tensile properties, would be 10% lighter.

  18. Strength and cracking resistance of hot-deformed steel with a low-carbon martensite structure

    NASA Astrophysics Data System (ADS)

    Romanov, I. D.; Shatsov, A. A.; Kleiner, L. M.

    2013-10-01

    Effect of the structure of the low-carbon martensitic steel air-quenched from the temperature of the end of the hot deformation on the strength and impact-toughness characteristics has been studied. A connection between the sizes of typical structure elements and the level of mechanical properties was established.

  19. Digital image analysis to quantify carbide networks in ultrahigh carbon steels

    SciTech Connect

    Hecht, Matthew D.; Webler, Bryan A.; Picard, Yoosuf N.

    2016-07-15

    A method has been developed and demonstrated to quantify the degree of carbide network connectivity in ultrahigh carbon steels through digital image processing and analysis of experimental micrographs. It was shown that the network connectivity and carbon content can be correlated to toughness for various ultrahigh carbon steel specimens. The image analysis approach first involved segmenting the carbide network and pearlite matrix into binary contrast representations via a grayscale intensity thresholding operation. Next, the carbide network pixels were skeletonized and parceled into braches and nodes, allowing the determination of a connectivity index for the carbide network. Intermediate image processing steps to remove noise and fill voids in the network are also detailed. The connectivity indexes of scanning electron micrographs were consistent in both secondary and backscattered electron imaging modes, as well as across two different (50 × and 100 ×) magnifications. Results from ultrahigh carbon steels reported here along with other results from the literature generally showed lower connectivity indexes correlated with higher Charpy impact energy (toughness). A deviation from this trend was observed at higher connectivity indexes, consistent with a percolation threshold for crack propagation across the carbide network. - Highlights: • A method for carbide network analysis in steels is proposed and demonstrated. • ImageJ method extracts a network connectivity index from micrographs. • Connectivity index consistent in different imaging conditions and magnifications. • Impact energy may plateau when a critical network connectivity is exceeded.

  20. Effect of an atmosphere on the wetting of titanium carbide with liquid low-carbon steel

    NASA Astrophysics Data System (ADS)

    Chumanov, I. V.; Anikeev, A. N.

    2016-12-01

    The methodology and the experimental studies of the influence of an atmosphere on the wetting of titanium carbide with liquid low-carbon steel in various atmospheres are presented. The wetting of titanium carbide in an oxidizing atmosphere is found to be limited (the wetting angle is 97°-110°), while complete wetting takes place in vacuum and in an argon atmosphere.

  1. Numerical predictions of dry oxidation of iron and low-carbon steel at moderately elevated temperatures

    SciTech Connect

    Henshall, G.A.

    1996-11-01

    Wrought and cast low-carbon steel are candidate materials for the thick (e.g. 10 cm) outer barrier of nuclear waste packages being considered for use in the potential geological repository at Yucca Mountain. Dry oxidation is possible at the moderately elevated temperatures expected at the container surface (323-533 K or 50-260 C). Numerical predictions of dry oxidation damage were made based on experimental data for iron and low-carbon steel and parabolic oxidation theory. The Forward Euler method was implemented to integrate the parabolic rate law for arbitrary, complex temperature histories. Assuming growth of a defect-free, adherent oxide, the surface penetration of a low-carbon steel barrier following 5000 years of exposure to a severe, but repository-relevant, temperature history is predicted to be only about 0.127 mm, less than 0.13% of the expected container thickness of 10 cm. Allowing the oxide to spall upon reaching a critical thickness increases the predicted metal penetration values, but degradation is still computed to be negligible. Thus, dry oxidation is not expected to significantly degrade the performance of thick, corrosion allowance barriers constructed of low-carbon steel.

  2. Contributions of Vanadium to Properties of Heat Treated Medium Carbon Forging Steels

    NASA Astrophysics Data System (ADS)

    Rothleutner, L. M.; Van Tyne, C. J.; Glodowski, R. J.; Speer, J. G.; Matlock, D. K.

    Potential benefits of vanadium in heat treated medium carbon bar steels are considered by reviewing examples from several recent studies. Emphasis is placed on microstructural development, strength, and fatigue performance after conventional and induction heat treating. Potential areas for future research are identified.

  3. Regularities of Macroscopic Localization of Plastic Deformation in the Stretching of a Low-Carbon Steel

    NASA Astrophysics Data System (ADS)

    Barannikova, S. A.; Kosinov, D. A.; Nadezhkin, M. V.; Lunev, A. G.; Gorbatenko, V. V.; Zuev, L. B.; Gromov, V. E.

    2014-07-01

    The special features of plastic deformation localization in the stretching of polycrystals of low-carbon steel 08 ss after hot rolling and electrolytic saturation with hydrogen are investigated. The main types and parameters of plastic flow localization in different stages of strain hardening are determined by the method of double-exposure speckle photography.

  4. Isothermal superplastic boronizing of high carbon and low alloy steels

    SciTech Connect

    Xu, C.H.; Gao, W.; Xi, J.K.

    1996-02-01

    Superplasticity has been developed rapidly since the 1960`s. Superplasticity and superplastic deformation technique of steel and ferrous alloys offer a new method of forming complex parts for industrial applications, such as dies and gears. On the other hand, boronizing has long been used to improve the surface properties of dies and tools because boride has high hardness, good wear resistance, and good corrosion and oxidation resistance. Superplastic boronizing, a new technique, is the processes that combines boronizing with superplastic deformation. Because two processes become one, energy and time can be saved. In the present paper, the superplastic boronizing processes for commercial 0.9C-1Si-1Cr-Fe and 1C-1Cr-Fe steels are described first. Then, the microstructure and properties of specimens produced by using superplastic and conventional boronizing are compared. Finally, a physical model for superplastic boronizing processes is suggested.

  5. Corrosion of carbon steel by bacteria from North Sea offshore seawater injection systems: laboratory investigation.

    PubMed

    Stipanicev, Marko; Turcu, Florin; Esnault, Loïc; Rosas, Omar; Basseguy, Régine; Sztyler, Magdalena; Beech, Iwona B

    2014-06-01

    Influence of sulfidogenic bacteria, from a North Sea seawater injection system, on the corrosion of S235JR carbon steel was studied in a flow bioreactor; operating anaerobically for 100days with either inoculated or filtrated seawater. Deposits formed on steel placed in reactors contained magnesium and calcium minerals plus iron sulfide. The dominant biofilm-forming organism was an anaerobic bacterium, genus Caminicella, known to produce hydrogen sulfide and carbon dioxide. Open Circuit Potentials (OCP) of steel in the reactors was, for nearly the entire test duration, in the range -80045), suggested pitting on steel samples within the inoculated environment. However, the actual degree of corrosion could neither be directly correlated with the electrochemical data and nor with the steel corrosion in the filtrated seawater environment. Further laboratory tests are thought to clarify the noticed apparent discrepancies.

  6. Mechanical Behavior of Steel Fiber-Reinforced Concrete Beams Bonded with External Carbon Fiber Sheets.

    PubMed

    Gribniak, Viktor; Tamulenas, Vytautas; Ng, Pui-Lam; Arnautov, Aleksandr K; Gudonis, Eugenijus; Misiunaite, Ieva

    2017-06-17

    This study investigates the mechanical behavior of steel fiber-reinforced concrete (SFRC) beams internally reinforced with steel bars and externally bonded with carbon fiber-reinforced polymer (CFRP) sheets fixed by adhesive and hybrid jointing techniques. In particular, attention is paid to the load resistance and failure modes of composite beams. The steel fibers were used to avoiding the rip-off failure of the concrete cover. The CFRP sheets were fixed to the concrete surface by epoxy adhesive as well as combined with various configurations of small-diameter steel pins for mechanical fastening to form a hybrid connection. Such hybrid jointing techniques were found to be particularly advantageous in avoiding brittle debonding failure, by promoting progressive failure within the hybrid joints. The use of CFRP sheets was also effective in suppressing the localization of the discrete cracks. The development of the crack pattern was monitored using the digital image correlation method. As revealed from the image analyses, with an appropriate layout of the steel pins, brittle failure of the concrete-carbon fiber interface could be effectively prevented. Inverse analysis of the moment-curvature diagrams was conducted, and it was found that a simplified tension-stiffening model with a constant residual stress level at 90% of the strength of the SFRC is adequate for numerically simulating the deformation behavior of beams up to the debonding of the CFRP sheets.

  7. Mechanical Behavior of Steel Fiber-Reinforced Concrete Beams Bonded with External Carbon Fiber Sheets

    PubMed Central

    Gribniak, Viktor; Tamulenas, Vytautas; Ng, Pui-Lam; Arnautov, Aleksandr K.; Gudonis, Eugenijus; Misiunaite, Ieva

    2017-01-01

    This study investigates the mechanical behavior of steel fiber-reinforced concrete (SFRC) beams internally reinforced with steel bars and externally bonded with carbon fiber-reinforced polymer (CFRP) sheets fixed by adhesive and hybrid jointing techniques. In particular, attention is paid to the load resistance and failure modes of composite beams. The steel fibers were used to avoiding the rip-off failure of the concrete cover. The CFRP sheets were fixed to the concrete surface by epoxy adhesive as well as combined with various configurations of small-diameter steel pins for mechanical fastening to form a hybrid connection. Such hybrid jointing techniques were found to be particularly advantageous in avoiding brittle debonding failure, by promoting progressive failure within the hybrid joints. The use of CFRP sheets was also effective in suppressing the localization of the discrete cracks. The development of the crack pattern was monitored using the digital image correlation method. As revealed from the image analyses, with an appropriate layout of the steel pins, brittle failure of the concrete-carbon fiber interface could be effectively prevented. Inverse analysis of the moment-curvature diagrams was conducted, and it was found that a simplified tension-stiffening model with a constant residual stress level at 90% of the strength of the SFRC is adequate for numerically simulating the deformation behavior of beams up to the debonding of the CFRP sheets. PMID:28773024

  8. Hot Deformation Behavior and Dynamic Recrystallization of Medium Carbon LZ50 Steel

    NASA Astrophysics Data System (ADS)

    Du, Shiwen; Chen, Shuangmei; Song, Jianjun; Li, Yongtang

    2017-01-01

    Hot deformation and dynamic recrystallization behaviors of a medium carbon steel LZ50 were systematically investigated in the temperature range from 1143 K to 1443 K (870 °C to 1170 °C) at strain rates from 0.05 to 3s-1 using a Gleeble-3500 thermo-simulation machine. The flow stress constitutive equation for hot deformation of this steel was developed with the two-stage Laasraoui equation. The activation energy of the tested steel was 304.27 KJ/mol, which was in reasonable agreement with those reported previously. The flow stress of this steel in hot deformation was mainly controlled by dislocation climb during their intragranular motion. The effect of Zener-Hollomon parameter on the characteristic points of the flow curves was studied, and the dependence of critical strain on peak strain obeyed a linear equation. Dynamic recrystallization was the most important softening mechanism for the tested steel during hot deformation. Kinetic equation of this steel was also established based on the flow stress. The austenite grain size of complete dynamic recrystallization was a power law function of Zener-Hollomon parameter with an exponent of -0.2956. Moreover, the microstructures induced under different deformation conditions were analyzed.

  9. Hot Deformation Behavior and Dynamic Recrystallization of Medium Carbon LZ50 Steel

    NASA Astrophysics Data System (ADS)

    Du, Shiwen; Chen, Shuangmei; Song, Jianjun; Li, Yongtang

    2017-03-01

    Hot deformation and dynamic recrystallization behaviors of a medium carbon steel LZ50 were systematically investigated in the temperature range from 1143 K to 1443 K (870 °C to 1170 °C) at strain rates from 0.05 to 3s-1 using a Gleeble-3500 thermo-simulation machine. The flow stress constitutive equation for hot deformation of this steel was developed with the two-stage Laasraoui equation. The activation energy of the tested steel was 304.27 KJ/mol, which was in reasonable agreement with those reported previously. The flow stress of this steel in hot deformation was mainly controlled by dislocation climb during their intragranular motion. The effect of Zener-Hollomon parameter on the characteristic points of the flow curves was studied, and the dependence of critical strain on peak strain obeyed a linear equation. Dynamic recrystallization was the most important softening mechanism for the tested steel during hot deformation. Kinetic equation of this steel was also established based on the flow stress. The austenite grain size of complete dynamic recrystallization was a power law function of Zener-Hollomon parameter with an exponent of -0.2956. Moreover, the microstructures induced under different deformation conditions were analyzed.

  10. Rehabilitation of notch damaged steel beam using a carbon fiber reinforced multiphase-matrix composite

    SciTech Connect

    Zhou, HongYu; Attard, Dr. Thomas L.; Wang, Yanli; Wang, Jy-An John; Ren, Fei

    2013-01-01

    The retrofit of notch damaged steel beams is investigated via the experimental testing of nine wide-flange steel beam specimens and finite element simulation. Three notch configurations representing various damage levels were identified, and the beam specimens were retrofitted using CFRP laminates and a recently developed polymeric matrix composite - CarbonFlex - that exhibits superior energy dissipation and ductility properties, where the peak-load deflections were between 49.4% and 65.2% higher using the CarbonFlex-retrofitted beams. The results are attributed to the substantially higher damage tolerance capability of CarbonFlex than conventional CFRP. Finite element models were developed to investigate the damage processes and strain/ stress distributions near the notch tips. The numerical results match closely with the experimentally determined load-deflection curves and the strain fields obtained by the digital imaging correlations (DIC) system. Both experimental and numerical results clearly indicate the effectiveness of CarbonFlex, as a candidate retrofitting material, to retrofit damaged steel structures. Lastly, the micro-mechanisms by which CarbonFlex could sufficiently sustain a significant amount of the peak strength at large displacement ductility values are discussed with the aid of scanning electron microscopy (SEM) pictures.

  11. Effects of tantalum content on the microstructure and mechanical properties of low-carbon RAFM steel

    NASA Astrophysics Data System (ADS)

    Chen, Jianguo; Liu, Chenxi; Liu, Yongchang; Yan, Biyu; Li, Huijun

    2016-10-01

    In order to explore the influence of tantalum content on the microstructure and mechanical properties of low carbon RAFM (reduced activation ferritic/martensitic) steels, three low carbon RAFM steels with different tantalum contents (0%, 0.027%, 0.073%) were designed. The precipitation behavior and effect of precipitates on the mechanical properties of the Low-C RAFM steel were investigated. The results indicate that increase of tantalum content causes decrease of the prior austenite grain size and the amount of M23C6 carbides precipitated along prior austenite grain boundaries and packet boundaries as well as increase of the amount of MX nano-sized particles within intragranular regions. The impact properties of low carbon RAFM steels are excellent regardless of the tantalum content. The impact properties and hardness are obviously improved by increasing tantalum content, which may be related to increase of the number of MX and decrease of M23C6. Furthermore, the tensile properties at elevated temperature below 600 °C are hardly changed with increase of tantalum content, yet those at 800 °C are improved with increasing tantalum content. This implies that MX carbides would be more important for tensile properties at higher temperature.

  12. Effect of temper rolling on the bake-hardening behavior of low carbon steel

    NASA Astrophysics Data System (ADS)

    Kuang, Chun-fu; Zhang, Shen-gen; Li, Jun; Wang, Jian; Li, Pei

    2015-01-01

    In a typical process, low carbon steel was annealed at two different temperatures (660°C and 750°C), and then was temper rolled to improve the mechanical properties. Pre-straining and baking treatments were subsequently carried out to measure the bake-hardening (BH) values. The influences of annealing temperature and temper rolling on the BH behavior of the steel were investigated. The results indicated that the microstructure evolution during temper rolling was related to carbon atoms and dislocations. After an apparent increase, the BH value of the steel significantly decreased when the temper rolling reduction was increased from 0% to 5%. This was attributed to the increase in solute carbon concentration and dislocation density. The maximum BH values of the steel annealed at 660°C and 750°C were 80 MPa and 89 MPa at the reductions of 3% and 4%, respectively. Moreover, increasing the annealing temperature from 660 to 750°C resulted in an obvious increase in the BH value due to carbide dissolution.

  13. A technique for brazing graphite/graphite and stainless steel/high-carbon steel joints

    SciTech Connect

    Ohmura, H.; Kawashiri, K. . Dept. of Metals and Inorganic Materials); Yoshida, T. . Vehicle Machine Engineering Dept.); Yoshimoto, O. . Quality Control Dept.)

    1994-10-01

    A new brazing technique for joining graphite to itself or to metals such as Mo, W, or Cu, with conventional brazing filler metals has been developed. Essentially, it is impossible to braze graphite with Cu filler metal because no wetting occurs. However, when a graphite base material is combined with an Fe base metal in Cu brazing, the Fe base metal dissolves in molten Cu. Simultaneously, the dissolved Fe grows as part of a columnar Fe-9 [approximately] 6Cu-1.6C alloy phase at the graphite interface at a constant brazing temperature, that is, the dissolution and deposit of base metal takes place. By placing an Fe foil insert between both graphite base materials, therefore, the columnar phase is formed at both graphite faces and grows toward the Fe foil during heating. As a result, both graphite base materials are united by the columnar phase through the Fe foil. In the same way, a graphite/Mo or /W joint can be produced. Moreover, when using BAu-1, which has a lower melting point than that of BCu-1, it is also possible to braze graphite to Cu. The shear strength of a graphite/graphite joint with a 0.12-mm thick Fe foil at room temperature was about 32 MPa. Further, the bending strength of the graphite/graphite and /Cu joints at 873 K (1,112 F), as measured using the four-point bending test, was 35 and 11 MPa, respectively. In addition, the technique can be applied to the brazing of AISI 304 stainless steel to high-C steel with BCu-1 where, normally, Cr[sub 23]C[sub 6] and Cr[sub 7]C[sub 3] layers are formed at the high-C steel braze interface; these carbide layers result in the loss of mechanical properties of the joint.

  14. The effect of hydrogen on the parameters of plastic deformation localization in low carbon steel

    SciTech Connect

    Lunev, Aleksey G. E-mail: nadjozhkin@ispms.tsc.ru; Nadezhkin, Mikhail V. E-mail: nadjozhkin@ispms.tsc.ru; Shlyakhova, Galina V.; Barannikova, Svetlana A.; Zuev, Lev B.

    2014-11-14

    In the present study, the effect of interstitial hydrogen atoms on the mechanical properties and plastic strain localization patterns in tensile tested polycrystals of low-carbon steel Fe-0.07%C has been studied using double exposure speckle photography technique. The main parameters of plastic flow localization at various stages of deformation hardening have been determined in polycrystals of steel electrolytically saturated with hydrogen in a three-electrode electrochemical cell at a controlled constant cathode potential. Also, the effect of hydrogen on changing of microstructure by using optical microscopy has been demonstrated.

  15. Cladding of the carbon fiber on the steel base using electron beam in the air atmosphere

    NASA Astrophysics Data System (ADS)

    Losinskaya, A.; Lozhkina, E.; Bardin, A.; Stepanova, N.

    2016-11-01

    The formation of the high-carbon layers on the low-carbon steel (0.18 % C) using the method of electron-beam partial melting of the carbon fibers is considered. A 1.4 MeV electron beam extracted into air was used. The features of the cladded layers formation using different binders for a reliable fixation of the cladding material are studied. It is revealed that the best results are obtained using the phenol-formaldehyde glue as the binder. A 3 mm thickness layers with 2.2 % C are shown to be formed.

  16. Low-carbon transition of iron and steel industry in China: carbon intensity, economic growth and policy intervention.

    PubMed

    Yu, Bing; Li, Xiao; Qiao, Yuanbo; Shi, Lei

    2015-02-01

    As the biggest iron and steel producer in the world and one of the highest CO2 emission sectors, China's iron and steel industry is undergoing a low-carbon transition accompanied by remarkable technological progress and investment adjustment, in response to the macroeconomic climate and policy intervention. Many drivers of the CO2 emissions of the iron and steel industry have been explored, but the relationships between CO2 abatement, investment and technological expenditure, and their connections with the economic growth and governmental policies in China, have not been conjointly and empirically examined. We proposed a concise conceptual model and an econometric model to investigate this crucial question. The results of regression, Granger causality test and impulse response analysis indicated that technological expenditure can significantly reduce CO2 emissions, and that investment expansion showed a negative impact on CO2 emission reduction. It was also argued with empirical evidence that a good economic situation favored CO2 abatement in China's iron and steel industry, while achieving CO2 emission reduction in this industrial sector did not necessarily threaten economic growth. This shed light on the dispute over balancing emission cutting and economic growth. Regarding the policy aspects, the year 2000 was found to be an important turning point for policy evolution and the development of the iron and steel industry in China. The subsequent command and control policies had a significant, positive effect on CO2 abatement. Copyright © 2014. Published by Elsevier B.V.

  17. Carbon steel wettability characteristics enhancement for improved enamelling using a 1.2 kW high power diode laser

    NASA Astrophysics Data System (ADS)

    Lawrence, J.; Li, L.

    High-power diode laser (HPDL) surface treatment of a common engineering carbon steel (EN8) was found to effect significant changes to the wettability characteristics of the metal. These modifications have been investigated in terms of the changes in the surface roughness of the steel, the presence of any surface melting, the polar component of the steel surface energy and the relative surface oxygen content of the steel. The morphological and wetting characteristics of the mild steel and the enamel were determined using optical microscopy, scanning electron microscopy (SEM), X-ray photoemission spectroscopy (XPS), energy-dispersive X-ray (EDX) analysis and wetting experiments by the sessile drop technique. This work has shown that HPDL radiation can be used to alter the wetting characteristics of carbon steel so as to facilitate improved enamelling.

  18. Carbon steel wettability characteristics enhancement for improved enamelling using a 1.2 kW high power diode laser

    NASA Astrophysics Data System (ADS)

    Lawrence, J.; Li, L.

    1999-10-01

    High-power diode laser (HPDL) surface treatment of a common engineering carbon steel (EN8) was found to effect significant changes to the wettability characteristics of the metal. These modifications have been investigated in terms of the changes in the surface roughness of the steel, the presence of any surface melting, the polar component of the steel surface energy and the relative surface oxygen content of the steel. The morphological and wetting characteristics of the mild steel and the enamel were determined using optical microscopy, scanning electron microscopy (SEM), X-ray photoemission spectroscopy (XPS), energy-dispersive X-ray (EDX) analysis and wetting experiments by the sessile drop technique. This work has shown that HPDL radiation can be used to alter the wetting characteristics of carbon steel so as to facilitate improved enamelling.

  19. Color Anodizing of Titanium Coated Rolled Carbon Steel Plate

    SciTech Connect

    Sarajan, Zohair; Mobarakeh, Hooman Nikbakht; Namiranian, Sohrab

    2011-12-26

    As an important kind of structural materials, the titanium cladded steel plates have the advantages of both metals and have been applied in aviation, spaceflight, chemical and nuclear industries. In this study, the specimens which were prepared under soldering mechanism during rolling were anodized by electrochemical process under a given conditions. The color anodizing takes place by physical phenomenon of color interference. Part of incident light on the titanium oxide is reflected and the other part reflects inside coated titanium layer. Major part of the light which reflects from titanium-oxide interface, reflects again inside of the oxide layer.

  20. Carbon, nitrogen, and oxygen ion implantation of stainless steel

    SciTech Connect

    Rej, D.J.; Gavrilov, N.V.; Emlin, D.

    1995-12-31

    Ion implantation experiments of C, N, and O into stainless steel have been performed, with beam-line and plasma source ion implantation methods. Acceleration voltages were varied between 27 and 50 kV, with pulsed ion current densities between 1 and 10 mA/cm{sup 2}. Implanted doses ranged from 0.5 to 3 {times} 10{sup 18}cm{sup -2}, while workpiece temperatures were maintained between 25 and 800 C. Implant concentration profiles, microstructure, and surface mechanical properties of the implanted materials are reported.

  1. Marine Structural Steel Toughness Data Bank. Volume 4

    DTIC Science & Technology

    1990-08-31

    A588 GR A K11430 1-12A588 Gr B A588 Gr B K12043 1-12 A588 Gr C A588 Gr C K11538 1-12A537-A A537 Gr A K02400 1-13 API 5L Gr X60 1-14 A656-70 A656 Gr 70...and HSLA 80 containing primarily Cu, Ni, Cr and Mo; • Medium to high strength low alloy steels A537, CG-537, A656, A737, ABS-EH36, and API 5L...ASTM UNS PRIORITY NAME SPEC NUMBER HYS0 A543 Gr C(1) K31820 1-1 A710-A A710 Gr A K20747 1-2 CG A537M A537 Cl 1 K12437 1-3ABS-B A131 Gr B K02102 1-4 API

  2. Hybrid/Tandem Laser-Arc Welding of Thick Low Carbon Martensitic Stainless Steel Plates =

    NASA Astrophysics Data System (ADS)

    Mirakhorli, Fatemeh

    High efficiency and long-term life of hydraulic turbines and their assemblies are of utmost importance for the hydropower industry. Usually, hydroelectric turbine components are made of thick-walled low carbon martensitic stainless steels. The assembly of large hydroelectric turbine components has been a great challenge. The use of conventional welding processes involves typical large groove design and multi-pass welding to fill the groove which exposes the weld to a high heat input creating relatively large fusion zone and heat affected zone. The newly-developed hybrid/tandem laser-arc welding technique is believed to offer a highly competitive solution to improve the overall hydro-turbine performance by combining the high energy density and fast welding speed of the laser welding technology with the good gap bridging and feeding ability of the gas metal arc welding process to increase the productivity and reduce the consumable material. The main objective of this research work is to understand different challenges appearing during hybrid laser-arc welding (HLAW) of thick gauge assemblies of low carbon 13%Cr- 4%Ni martensitic stainless steel and find a practical solution by adapting and optimizing this relatively new welding process in order to reduce the number of welding passes necessary to fill the groove gap. The joint integrity was evaluated in terms of microstructure, defects and mechanical properties in both as-welded and post-welded conditions. A special focus was given to the hybrid and tandem laser-arc welding technique for the root pass. Based on the thickness of the low carbon martensitic stainless steel plates, this work is mainly focused on the following two tasks: • Single pass hybrid laser-arc welding of 10-mm thick low carbon martensitic stainless steel. • Multi-pass hybrid/tandem laser-arc welding of 25-mm thick martensitic stainless steel.

  3. Effect of carbon and nitrogen on the properties of chromium-manganese steels of the Kh16G18 type

    NASA Astrophysics Data System (ADS)

    Bannykh, O. A.; Pestryakova, E. P.; Rakhshtadt, A. G.; Barseg'yan, L. V.; Blinov, V. M.

    1991-01-01

    It is established that the level of carbide and nitride phase dissolution in chromium-manganese steels of type Kh16G18 with a varible ratio of carbon and nitrogen in them reaches a maximum at 1150°C. With an almost identical lattice spacing the degree of its distortion in steel with nitrogen is greater and therefore the specific electrical resistivity of the steel is higher.

  4. Electrochemical and Dry Sand Impact Erosion Studies on Carbon Steel

    PubMed Central

    Naz, M. Y.; Ismail, N. I.; Sulaiman, S. A.; Shukrullah, S.

    2015-01-01

    This study investigated the dry and aqueous erosion of mild steel using electrochemical and dry sand impact techniques. In dry sand impact experiments, mild steel was eroded with 45 μm and 150 μm sand particles. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and micro-hardness techniques were used to elaborate the surface morphology of the eroded samples. The results revealed significant change in morphology of the eroded samples. In-depth analysis showed that although the metal erosion due to larger particles was significantly higher, the fines also notably damaged the metal surface. The surface damages were appreciably reduced with decrease in impact angle of the accelerated particles. The maximum damages were observed at an impact angle of 90°. The hardness of the samples treated with 45 μm and 150 μm sand remained in the range of 88.34 to 102.31 VHN and 87.7 to 97.55 VHN, respectively. In electrochemical experiments, a triple electrode probe was added into the metal treatment process. The linear polarization resistance (LPR) measurements were performed in slurries having 5% (by weight) of sand particles. LPR of the samples treated with 45 μm and 150 μm sand slurries was calculated about 949 Ω.cm2 and 809 Ω.cm2, respectively. PMID:26561231

  5. Performance evaluation for carbonation of steel-making slags in a slurry reactor.

    PubMed

    Chang, E-E; Chen, Chung-Hua; Chen, Yi-Hung; Pan, Shu-Yuan; Chiang, Pen-Chi

    2011-02-15

    CO(2) sequestration by the aqueous carbonation of steel-making slag under various operational conditions was investigated in this study. The effects of the operational conditions, including type of steel-making slag, reaction time, reaction temperature, and CO(2) flow rate, on the performance of the carbonation process were evaluated. The results indicated that the BOF slag had the highest carbonation conversion, approximately 72%, at a reaction time of 1h, an operating pressure of 101 kPa and a temperature of 60°C due to its higher BET surface area of BOF slag compared to UF, FA, and BHC slags. The major factors affecting the carbonation conversion are reaction time and temperature. The reaction kinetics of the carbonation conversion can be expressed by the shrinking-core model. The measurements of the carbonated material by the SEM and XRD instruments provide evidence indicating the suitability of using the shrinking-core model in this investigation. Comparison of the results with other studies suggests that aqueous carbonation by slurry reactor is viable due to its higher mass transfer rate. Copyright © 2010 Elsevier B.V. All rights reserved.

  6. Monitoring of stainless-steel slag carbonation using X-ray computed microtomography.

    PubMed

    Boone, Marijn A; Nielsen, Peter; De Kock, Tim; Boone, Matthieu N; Quaghebeur, Mieke; Cnudde, Veerle

    2014-01-01

    Steel production is one of the largest contributors to industrial CO2 emissions. This industry also generates large amounts of solid byproducts, such as slag and sludge. In this study, fine grained stainless-steel slag (SSS) is valorized to produce compacts with high compressive strength without the use of a hydraulic binder. This carbonation process is investigated on a pore-scale level to identify how the mineral phases in the SSS react with CO2, where carbonates are formed, and what the impact of these changes is on the pore network of the carbonated SSS compact. In addition to conventional research techniques, high-resolution X-ray computed tomography (HRXCT) is applied to visualize and quantify the changes in situ during the carbonation process. The results show that carbonates mainly precipitate at grain contacts and in capillary pores and this precipitation has little effect on the connectivity of the pore space. This paper also demonstrates the use of a custom-designed polymer reaction cell that allows in situ HRXCT analysis of the carbonation process. This shows the distribution and influence of water and CO2 in the pore network on the carbonate precipitation and, thus, the influence on the compressive strength development of the waste material.

  7. Hot Deformation Behavior and Microstructural Evolution of a Medium Carbon Vanadium Microalloyed Steel

    NASA Astrophysics Data System (ADS)

    Cutrim, Rialberth M.; Rodrigues, Samuel F.; Reis, Gedeon S.; Silva, Eden S.; Aranas, Clodualdo; Balancin, Oscar

    2016-11-01

    Hot forging of steel requires application of large strains, under which conditions, dynamic recrystallization (DRX) is expected to take place. In this study, torsion tests were carried out on a medium carbon vanadium microalloyed steel (38MnSiVS5) to simulate hot forging. Deformations were applied isothermally in the temperature range 900-1200 °C at strain rates of 0.1-10 s-1 in order to observe for the occurrence of DRX and to investigate for the microstructural evolution during straining. The shape of the flow curves indicated that the recrystallization takes place during deformation. This was supported by optical microscopy performed on the quenched samples which displayed considerable amounts of recrystallized grains. It was shown that the grain size depends on straining conditions such as strain rate and temperature. Finally, it was revealed that these process parameters can considerably affect the evolution of microstructure of industrial grade steels by means of DRX.

  8. Effect of friction stir processing on the tribological performance of high carbon steel.

    SciTech Connect

    Aldajah, S. H.; Ajayi, O. O.; Fenske, G. R.; David, S.

    2009-06-15

    Friction stir processing (FSP) was applied to 1080 carbon steel as a means to enhance the near-surface material properties. The process transformed the original pearlite microstructure to martensite, resulting in significant increase in surface hardness. This surface hardening produced a significant benefit for friction and wear behavior of the steel as measured by unidirectional sliding ball-on-flat testing. Under dry sliding, FSP reduced friction coefficient by approximately 25% and wear rate by an order of magnitude. Under oil lubrication, FSP had only a marginal effect on friction, but it reduced wear rates by a factor of 4. The improvement in tribological performance of 1080 steel by FSP technique is attributed to reduced plasticity of the near-surface material during sliding contact

  9. Corrosion protection of low-carbon steel using exopolysaccharide coatings from Leuconostoc mesenteroides.

    PubMed

    Finkenstadt, Victoria L; Côté, Gregory L; Willett, J L

    2011-06-01

    Corrosion of metals is a serious and challenging problem faced worldwide by industry. Purified Leuconostoc mesenteroides exopolysaccharide (EPS) coatings, cast from aqueous solution, inhibited the corrosion of low-carbon steel as determined by electrochemical impedance spectroscopy (EIS). There were two different corrosion behaviors exhibited when EPS films from different strains were cast onto the steel. One EPS coating reacted immediately with the steel substrate to form an iron (III) oxide layer ("rust") during the drying process while another did not. The samples that did not flash corrode had higher corrosion inhibition and formed an iron (II) passivation layer during EIS testing that persisted after the cells were disassembled. Corrosion inhibition was strain-specific as polysaccharides with similar structure did not have the same corrosion potential.

  10. Precipitation behavior in ultra-low-carbon steels containing titanium and niobium

    NASA Astrophysics Data System (ADS)

    Hua, M.; Garcia, C. I.; Deardo, A. J.

    1997-09-01

    This work revealed the basic mechanism for the stabilization of carbon in ultra-low-carbon (ULC) steels that contain moderate S (0.004 to 0.010 wt pct), adequate Ti (0.060 to 0.080), and low Mn (≤0.20). During cooling through the austenitic region to the ferritic, the initially formed sulfide particles (TiS) undergo an in situ transformation into carbosulfides (H-Ti4C2S2) by absorbing C and Ti. The transformation from TiS to H may be considered as a hybrid of shear and diffusion, i.e., faulted Ti8S9 (9R)+10[Ti]+9[C] → 4 1/2Ti4C2S2 (H). At low temperature (≤930 °C), the stabilization process continues through epitaxial growth of carbides on H phase, i.e., [M]+ x[C]+H → epitaxial MC x (on H). This mechanism differs from the traditional view of stabilization, where the carbon is removed from solution by the formation of free-standing or independently nucleated H and/or MCN precipitates. While these two forms of carbon stabilization are now well known, this article presents a method of predicting which mechanism of stabilization will be operative in a given steel based on its bulk composition. Implications bearing upon new ULC steel design, considering the role of S, will be discussed.

  11. Effect of the dendritic morphology on hot tearing of carbon steels

    NASA Astrophysics Data System (ADS)

    Ridolfi, M. R.

    2016-03-01

    Hot tears form during solidification in the brittle region of the dendritic front. Most hot tearing criteria are based on solid and fluid mechanics, being the phenomenon strictly depending on the solid resistance to applied strains and on the liquid capability of filling the void spaces. Modelling both mechanisms implies the precise description of the dendritic morphology. To this scope, the theory of coalescence of the dendritic arms at grain boundaries of Rappaz et al. has been applied, in this work, to the columnar growth of carbon steels by means of a simple mathematical model. Depending on the alloy composition, solid bridging starts at solid fractions down to about 0.8 and up to above 0.995 (very low carbon). The morphology of the brittle region changes drastically with increasing carbon and adding other solutes. In particular, ferritic dendrites, typical of low carbon steels, tend to offer short and wide interdendritic spaces to the surrounding liquid making possible their complete filling, and few solid bridges; peritectic steels show the rise of austenite growing and bridging rapidly in the interdendritic spaces, preventing void formation; austenitic dendrites form long and narrow interdendritic spaces difficult to reach for the liquid and with a lot of solid bridges. Sulphur addition mainly acts in delaying the coalescence end, more markedly in ferritic dendrites.

  12. 75 FR 1031 - Certain Hot-Rolled Carbon Steel Flat Products from India: Notice of Preliminary Results of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-08

    ... Doc No: 2010-128] DEPARTMENT OF COMMERCE International Trade Administration (A-533-820) Certain Hot... hot-rolled carbon steel flat products from India (``Indian Hot-Rolled'') manufactured by Essar Steel... on Indian Hot-Rolled. See Notice of Amended Final Antidumping Duty Determination of Sales at Less...

  13. 78 FR 15703 - Certain Hot-Rolled Carbon Steel Flat Products From India, Indonesia, the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-03-12

    ... International Trade Administration Certain Hot-Rolled Carbon Steel Flat Products From India, Indonesia, the... products from India, Indonesia, the People's Republic of China (PRC), Taiwan, Thailand, and Ukraine. The... steel flat products from India, Indonesia, the PRC, Taiwan, Thailand, and Ukraine, pursuant to section...

  14. 76 FR 62039 - Certain Hot-Rolled Carbon Steel Flat Products From India: Final Results of 2009-2010 Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-06

    ... referred to as interstitial-free (``IF'')) steels, high-strength low-alloy (``HSLA'') steels, and the... levels of elements such as titanium or niobium (also commonly referred to as columbium), or both, added... of example, are outside or specifically excluded from the scope of the order: Alloy hot-rolled carbon...

  15. Evaluation of cast carbon steel and aluminum for rack insert in MCO Mark 1A fuel basket

    SciTech Connect

    Graves, C.E., Fluor Daniel Hanford

    1997-03-21

    This document evaluates the effects ofusing a cast carbon steel or aluminum instead of 3O4L stainless steel in the construction ofthe fuel rack insert for the Spent Nuclear Fuel MCO Mark IA fuel baskets. The corrosion, structural, and cost effects are examined.

  16. Mechanical evaluation of hip cement spacer reinforcement with stainless steel Kirschner wires, titanium and carbon rods, and stainless steel mesh.

    PubMed

    Kaku, Nobuhiro; Tabata, Tomonori; Tsumura, Hiroshi

    2015-04-01

    In two-stage treatments for infections after total hip arthroplasty, antibiotic-loaded cement spacers help treat the infection by antibiotic elution and prevent contraction. However, such spacers are weak and may fracture while awaiting replacement, impairing functionality. We evaluated whether a Kirschner wire (K-wire) mounted into the spacer reinforced its strength along with the effects of the reinforcing material, position, and intensity. Spacers without reinforcing materials constituted the control group. As reinforcing materials, stainless steel K-wires (diameters 3 and 6 mm), titanium alloy and carbon fibers (diameter 3.175 mm), and stainless steel meshes (inner and outer diameters, 6 and 9 mm, respectively) were inserted into the spacer mold before filling with cement. The spacers complied with ISO 7206-4; a compressive load was applied using a testing machine with a velocity of 25.4 mm/min, and the maximum load was recorded. We used 1-3 K-wires positioned on the medial side, lateral side, neck only, and stem only and tested 3 specimens for each condition. The control group withstood the highest load. Stainless steel was the strongest material; 3-mm K-wires in the neck and lateral side withstood a higher load. The computed tomography (CT) imaging revealed a cavity between the K-wires and cement. When K-wires were inserted along the whole length, despite cement fractures, continuity was maintained because of the reinforcing materials. It is difficult to improve the reinforcing strength of spacers using K-wires; however, K-wires prevented dislocation of cement spacer fragments, which can help prevent contraction and facilitate spacer removal during replacement.

  17. Alternatives to reduce corrosion of carbon steel storage drums

    SciTech Connect

    Zirker, L.R.; Beitel, G.A.

    1995-11-01

    The major tasks of this research were (a) pollution prevention opportunity assessments on the overpacking operations for failed or corroded drums, (b) research on existing container corrosion data, (c) investigation of the storage environment of the new Resource Conservation and Recovery Act Type II storage modules, (d) identification of waste streams that demonstrate deleterious corrosion affects on drum storage life, and (e) corrosion test cell program development. Twenty-one waste streams from five US Department of Energy (DOE) sites within the DOE Complex were identified to demonstrate a deleterious effect to steel storage drums. The major components of these waste streams include acids, salts, and solvent liquids, sludges, and still bottoms. The solvent-based waste streams typically had the shortest time to failure: 0.5 to 2 years. The results of this research support the position that pollution prevention evaluations at the front end of a project or process will reduce pollution on the back end.

  18. Tensile and pack compressive tests of some sheets of aluminum alloy, 1025 carbon steel, and chromium-nickel steel

    NASA Technical Reports Server (NTRS)

    Atchison, C S; Miller, James A

    1942-01-01

    Tensile and compressive stress-strain curves, stress-deviation curves, and secant modulus-stress curves are given for longitudinal and transverse specimens of 17S-T, 24S-T, and 24S-RT aluminum-alloy sheet in thicknesses from 0.032 to 0.081 inch, 1025 carbon steel sheet in thicknesses of 0.054 and 0.120 inch, and chromium-nickel steel sheet in thicknesses form 0.020 to 0.0275 inch. Significant differences were found between the tensile and the compressive stress-strain curves, and also the corresponding corollary curves; similarly, differences were found between the curves for the longitudinal and transverse directions. These differences are of particular importance in considering the compressive strength of aircraft structures made of thin sheet. They are explored further for the case of compression by giving tangent modulus-stress curves in longitudinal and transverse compression and dimensionless curves of the ratio of tangent modulus to Young's modulus and of the ratio of reduced modulus for a rectangular section to Young's modulus, both plotted against the ratio of stress to secant yield strength.

  19. Surface preparation for non-destructive detection of surface cracks in stainless steel and carbon steel piping

    SciTech Connect

    Funderburg, I.M.

    1996-07-01

    Engineers within the chemical process industries are among other things, charged with the task of determining the reliability of piping and equipment. As part of this evaluation, the surfaces of process equipment and piping are often examined for evidence of stress corrosion cracking (SCC) or other tightly closed surface cracks. Presently there is no consensus as to which is the ``best`` technique for preparing and inspecting carbon steel and stainless steel vessels or piping for surface cracks. The specific concern within industry is that Stress Corrosion Cracking (SCC) might go undetected if the surface preparation closes over such tight cracks. This paper presents results of a study, MTI commissioned to collect additional data, examine the literature, and interview industrial materials engineers, independent inspection specialists, non-destructive examination consultants, and other representatives of industries that have equipment which must be inspected for surface cracks. Discussed are the differing surface preparation techniques used, the use of standards for evaluating the effectiveness of the techniques, and what is felt to be the ``Key Learnings`` from the investigation.

  20. Liquid Phase Sintering of Boron-Containing Powder Metallurgy Steel with Chromium and Carbon

    NASA Astrophysics Data System (ADS)

    Wu, Ming-Wei; Fan, Yu-Chi; Huang, Her-Yueh; Cai, Wen-Zhang

    2015-11-01

    Liquid phase sintering is an effective method to improve the densification of powder metallurgy materials. Boron is an excellent alloying element for liquid phase sintering of Fe-based materials. However, the roles of chromium and carbon, and particularly that of the former, on liquid phase sintering are still undetermined. This study demonstrated the effects of chromium and carbon on the microstructure, elemental distribution, boride structure, liquid formation, and densification of Fe-B-Cr and Fe-B-Cr-C steels during liquid phase sintering. The results showed that steels with 0.5 wt pct C densify faster than those without 0.5 wt pct C. Moreover, although only one liquid phase forms in Fe-B-Cr steel, adding 0.5 wt pct C reduces the formation temperature of the liquid phase by about 50 K (°C) and facilitates the formation of an additional liquid, resulting in better densification at 1473 K (1200 °C). In both Fe-B-Cr and Fe-B-Cr-C steels, increasing the chromium content from 1.5 to 3 wt pct raises the temperature of liquid formation by about 10 K (°C). Thermodynamic simulations and experimental results demonstrated that carbon atoms dissolved in austenite facilitate the eutectic reaction and reduce the formation temperature of the liquid phase. In contrast, both chromium and molybdenum atoms dissolved in austenite delay the eutectic reaction. Furthermore, the 3Cr-0.5Mo additive in the Fe-0.4B steel does not change the typical boride structure of M2B. With the addition of 0.5 wt pct C, the crystal structure is completely transformed from M2B boride to M3(B,C) boro-carbide.

  1. Mechanical resistance of carbon and stainless steel hand instruments used in a reciprocating handpiece

    PubMed Central

    Piasecki, Lucila; Al-Sudani, Dina; Rubini, Alessio Giansiracusa; Sonnino, Giampaolo; Bossù, Maurizio; Testarelli, Luca; Di Giorgio, Roberto; da Silva-Neto, Ulisses Xavier; Brandão, Christian Giampietro; Gambarini, Gianluca

    2013-01-01

    Summary Aim The manual files are still widely used for initial canal negotiation prior the use of nickel-titanium shaping instruments, to determine working length and to verify patency. A mechanical glide path can be performed using manual files with handpieces, such as M4 Handpiece (SybronEndo, USA) that allows a 30°/30° reciprocating motion. The Pathfinders (SybronEndo, USA) are hand files designed to negotiate complex canals, made from stainless steel (SS) or carbon steel (CS) alloys. The aim of this in vitro study was to compare cyclic fatigue resistance of these two different types of manual Pathfinder instruments used in a M4 reciprocating handpiece in double curved artificial canals. Materials and methods Manual instruments designed for glide path (size #9 ISO .02 taper) made from different alloys were selected: Group SS -stainless steel Pathfinders (Sybron Endo) and Group CS - carbon steel Pathfinders size K2 (Sybron Endo). Ten instruments of each group were tested for resistance to cyclic fatigue with a reciprocating M4 handpiece inside an artificial S-shaped canal; the time to fracture was recorded for each file and data were statistically analyzed (ANOVA). Results Mean values (and SD) were 527 (± 89) seconds for the CS instruments and 548 (± 104) seconds for the SS files. No significant differences were observed between groups (p=0,062). Conclusions According to the results, both carbon and stainless steel instruments presented similar fatigue resistance when used with M4 reciprocating handpiece in double curved canals. PMID:24611091

  2. Comparison of carbon footprints of steel versus concrete pipelines for water transmission.

    PubMed

    Chilana, Lalit; Bhatt, Arpita H; Najafi, Mohammad; Sattler, Melanie

    2016-05-01

    The global demand for water transmission and service pipelines is expected to more than double between 2012 and 2022. This study compared the carbon footprint of the two most common materials used for large-diameter water transmission pipelines, steel pipe (SP) and prestressed concrete cylinder pipe (PCCP). A planned water transmission pipeline in Texas was used as a case study. Four life-cycle phases for each material were considered: material production and pipeline fabrication, pipe transportation to the job site, pipe installation in the trench, and operation of the pipeline. In each phase, the energy consumed and the CO2-equivalent emissions were quantified. It was found that pipe manufacturing consumed a large amount of energy, and thus contributed more than 90% of life cycle carbon emissions for both kinds of pipe. Steel pipe had 64% larger CO2-eq emissions from manufacturing compared to PCCP. For the transportation phase, PCCP consumed more fuel due to its heavy weight, and therefore had larger CO2-eq emissions. Fuel consumption by construction equipment for installation of pipe was found to be similar for steel pipe and PCCP. Overall, steel had a 32% larger footprint due to greater energy used during manufacturing. This study compared the carbon footprint of two large-diameter water transmission pipeline materials, steel and prestressed concrete cylinder, considering four life-cycle phases for each. The study provides information that project managers can incorporate into their decision-making process concerning pipeline materials. It also provides information concerning the most important phases of the pipeline life cycle to target for emission reductions.

  3. Effect of organic acid on CO{sub 2} corrosion of carbon and Cr bearing steels

    SciTech Connect

    Ueda, Masakatsu; Takabe, Hideki

    1998-12-31

    The effect of organic acid on CO{sub 2} corrosion of carbon and Cr bearing steels was investigated. Acetic acid was considered as the organic acid. The temperature(T{sub max}), which gave a maximum corrosion rate, was observed on pure iron, and 1 and 2%Cr steels in the CO{sub 2} environment with 0.5% CH{sub 3}COOH as well as in the CO{sub 2} environment without CH{sub 3}COOH. The corrosion rate of these steels at T{sub max} extremely increased due to the addition of 0.5% CH{sub 3}COOH, but the T{sub max} did not change. In 9 and 13% Cr steels, the T{sub max} was observed in the CO{sub 2} environment without CH{sub 3}COOH, but did not in the CO{sub 2} environment with 5% CH{sub 3}COOH, and those corrosion rates continued to increase at the temperature above the T{sub max} in the CO{sub 2} environment without CH{sub 3}COOH. These corrosion behaviors were discussed from a viewpoint of pH and FeCO{sub 3} formation condition which was led from the calculated-equilibrium volubility of FeCO{sub 3} at elevated temperatures. Then, those were related to the acceleration of corrosion at the steel surface with heterogeneous FeCO{sub 3} film in pure iron, and 1 and 2% Cr steels, and the different formation behavior of corrosion products at the temperatures below and above 200 C in 9 and 13% Cr steels.

  4. 76 FR 20954 - Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Extension of Time...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-14

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE International Trade Administration Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea..., the Department published in the Federal Register the countervailing duty order on...

  5. 75 FR 18153 - Corrosion-Resistant Carbon Steel Flat Products from the Republic of Korea: Extension of Time...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-04-09

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE International Trade Administration Corrosion-Resistant Carbon Steel Flat Products from the Republic of Korea..., the Department published in the Federal Register the countervailing duty order on...

  6. 77 FR 67395 - Corrosion-Resistant Carbon Steel Flat Products From Germany and Korea; Revised Schedule for the...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-11-09

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Corrosion-Resistant Carbon Steel Flat Products From Germany and Korea; Revised Schedule for the Subject Reviews AGENCY: United States International Trade Commission. ACTION: Notice. DATES:...

  7. 77 FR 16810 - Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea: Extension of Time...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-22

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE International Trade Administration Corrosion-Resistant Carbon Steel Flat Products From the Republic of Korea..., the Department published in the Federal Register the countervailing duty order on...

  8. 78 FR 33809 - Seamless Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the People's Republic of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-05

    ... Carbon and Alloy Steel Standard, Line, and Pressure Pipe From the People's Republic of China: Rescission..., line, and pressure pipe from the People's Republic of China. The period of review is November 1, 2011... China covering the period [[Page 33810

  9. Inhibition effect of phosphorus-based chemicals on corrosion of carbon steel in secondary-treated municipal wastewater.

    PubMed

    Shen, Zhanhui; Ren, Hongqiang; Xu, Ke; Geng, Jinju; Ding, Lili

    2013-01-01

    Secondary-treated municipal wastewater (MWW) could supply a viable alternative water resource for cooling water systems. Inorganic salts in the concentrated cooling water pose a great challenge to corrosion control chemicals. In this study, the inhibition effect of 1-hydroxy ethylidene-1,1-diphosphonic acid (HEDP), trimethylene phosphonic acid (ATMP) and 2-phosphonobutane-1,2,4-tricarboxylic acid (PBTCA) on corrosion of carbon steel in secondary-treated MWW was investigated by the means of potentiodynamic polarization and electrochemical impedance spectroscopy. The inhibition effect increased with increasing concentration of inhibitors. The corrosion rates of carbon steel were 1.5, 0.8, 0.2 and 0.5 mm a(-1) for blank, HEDP, ATMP and PBTCA samples at 50 mg L(-1), respectively. The phosphorus-based chemicals could adsorb onto the surface of the carbon steel electrode, form a coat of protective film and then protect the carbon steel from corrosion in the test solution.

  10. 77 FR 64471 - Circular Welded Carbon-Quality Steel Pipe From the Socialist Republic of Vietnam: Final Negative...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-22

    ... Vietnam: Final Negative Countervailing Duty Determination AGENCY: Import Administration, International... welded carbon-quality steel pipe (``circular welded pipe'') from the Socialist Republic of Vietnam (``Vietnam''). DATES: Effective Date: October 22, 2012. FOR FURTHER INFORMATION CONTACT: Christopher...

  11. Mathematical Model for Decarburization of Ultra-low Carbon Steel in Single Snorkel Refining Furnace

    NASA Astrophysics Data System (ADS)

    You, Zhimin; Cheng, Guoguang; Wang, Xinchao; Qin, Zhe; Tian, Jun; Zhang, Jian

    2014-09-01

    A dynamic model is developed to investigate decarburization behavior of a new type of refining equipment named Single Snorkel Refining Furnace (SSRF) in treating ultra-low carbon steel. Decarburization reactions in SSRF are considered to take place at three sites: Ar bubble surface, the bulk steel, and the bath surface. With the eccentricity of the porous plug (r e/R S) and the ratio of the snorkel diameter to the ladle diameter (D S/D L) of SSRF confirmed, circulation flow rate of molten steel is obtained through combined effects of vacuum pressure and gas flow rate. Besides, variation of the steel temperature is simulated associated with generated reaction heat and heat losses. The variation of C concentration with treatment time is divided into three stages in accordance with decarburization rates and the simulated C concentration is in reasonable agreement with actual production data. In the present study, both decarburization rates at three sites and their contributions to the overall decarburization at each stage are estimated for the first time. Through the present investigation, it is clear that vacuum pressure significantly influences decarburization efficiency of SSRF primarily by affecting the depth of CO nucleation in the bulk steel. Besides, effects of gas flow rate on decarburization rate of different stages are obtained and the opportunity of increasing gas flow rate during the treatment period has been clarified. The present model provides an efficient tool to comprehend the decarburization process in SSRF.

  12. Mathematical Model for Decarburization of Ultra-low Carbon Steel in Single Snorkel Refining Furnace

    NASA Astrophysics Data System (ADS)

    You, Zhimin; Cheng, Guoguang; Wang, Xinchao; Qin, Zhe; Tian, Jun; Zhang, Jian

    2015-02-01

    A dynamic model is developed to investigate decarburization behavior of a new type of refining equipment named Single Snorkel Refining Furnace (SSRF) in treating ultra-low carbon steel. Decarburization reactions in SSRF are considered to take place at three sites: Ar bubble surface, the bulk steel, and the bath surface. With the eccentricity of the porous plug ( r e/ R S) and the ratio of the snorkel diameter to the ladle diameter ( D S/ D L) of SSRF confirmed, circulation flow rate of molten steel is obtained through combined effects of vacuum pressure and gas flow rate. Besides, variation of the steel temperature is simulated associated with generated reaction heat and heat losses. The variation of C concentration with treatment time is divided into three stages in accordance with decarburization rates and the simulated C concentration is in reasonable agreement with actual production data. In the present study, both decarburization rates at three sites and their contributions to the overall decarburization at each stage are estimated for the first time. Through the present investigation, it is clear that vacuum pressure significantly influences decarburization efficiency of SSRF primarily by affecting the depth of CO nucleation in the bulk steel. Besides, effects of gas flow rate on decarburization rate of different stages are obtained and the opportunity of increasing gas flow rate during the treatment period has been clarified. The present model provides an efficient tool to comprehend the decarburization process in SSRF.

  13. High ductility of bainite-based microstructure of middle carbon steel 42SiMn

    NASA Astrophysics Data System (ADS)

    Kučerová, L.; Bystrianský, M.; Jeníček, Š.

    2017-02-01

    Heat and thermo-mechanical treatments with various processing parameters were applied to middle carbon low alloyed 42SiMn steel. The aim of the treatment was to obtain multiphase microstructure typical for TRIP (Transformation induced plasticity) steel and to achieve the best combination of ultimate tensile strength and ductility. TRIP steels typically possess about 5-15% of metastable retained austenite, which can transform to martensite during plastic deformation. The gradual phase transformation during loading postpones the onset of necking, thus increasing ultimate tensile strength and ductility at the same time. Manganese and silicon, used as the main alloying elements of the experimental steel, are employed to increase austenite stability and to hinder cementite precipitation during the treatment. All proposed methods of heat and thermo-mechanical treatment contain bainitic hold at 400 °C or 425 °C. The final microstructures were very complex, consisting of bainite, ferrite, very small areas of extremely fine perlite lamellas, about 10% of retained austenite and M-A constituent (austenitic islands partially transformed to martensite). Even though pearlite and martensite are undesirable microstructure in TRIP steel, the tensile strength ranged from 850 to 1065 MPa and ductility A5mm from 26 to 47 %.

  14. Removal of copper from carbon-saturated steel with an aluminum sulfide/iron sulfide slag

    SciTech Connect

    Cohen, A.; Blander, M.

    1995-12-01

    Scrap iron and steel has long been considered a resource in the steel-making industry, and its value is largely determined by its impurity content. As the mini-mills, the major consumers of scrap iron and steel, expand into producing flat-rolled sheet, the demand for high-quality scrap will increase. Of the impurities present in scrap, copper is particularly troublesome because of its role in causing hot shortness. Therefore, the copper content of scrap should be kept below {approx} 0.1 wt%. A method for removing copper from steel could be used to improve the quality of scrap and make it more available for use by mini-mills. To determine the effectiveness of a binary slag consisting of aluminum sulfide and iron sulfide on the removal of copper from steel and iron, the distribution coefficient of copper between the slag and a carbon-saturated iron melt was investigated at 1,365 C. The composition of the slag was varied from nearly pure aluminum sulfide to pure iron sulfide. A maximum distribution coefficient of 30 was found, and the copper level in the iron melt was reduced to as low as 0.07 wt.% with a 4:1 ratio of iron to slag.

  15. Corrosion Behavior of Medium Carbon Steel in Simulated Concentrated Yucca Mountain Waters

    SciTech Connect

    Yilmaz, A; Chandra, D; Rebak, R B

    2004-04-09

    Medium carbon steel (MCS) is the candidate material for rock bolts to reinforce the borehole liners and emplacement drifts of the proposed Yucca Mountain (YM) high-level nuclear waste repository. Corrosion performance of this structural steel -AISI 1040- was investigated by techniques such as linear polarization, electrochemical impedance spectroscopy (EIS), and laboratory immersion tests in lab simulated concentrated YM ground waters. Corrosion rates of the steel were determined for the temperatures in the range from 25 C to 85 C, for the ionic concentrations of 1 time (1x), 10 times (10x), and hundred times (100x) ground waters. The MCS corroded uniformly at the penetration rates of 35-200 {micro}m/year in the de-aerated YM waters, and 200-1000 {micro}m/year in the aerated waters. Increasing temperatures in the de-aerated waters increased the corrosion rates of the steel. However, increasing ionic concentrations influenced the corrosion rates only slightly. In the aerated 1x and 10x waters, increasing temperatures increased the rates of MCS significantly. Inhibitive precipitates, which formed in the aerated 100x waters at higher temperatures (65 C and up) decreased the corrosion rates to the values that obtained for the de-aerated YM aqueous environments. The steel suffered pitting corrosion in the both de-aerated and aerated hot YM environments after anodic polarization.

  16. India's iron and steel industry: Productivity, energy efficiency and carbon emissions

    SciTech Connect

    Schumacher, Katja; Sathaye, Jayant

    1998-10-01

    Historical estimates of productivity growth in India's iron and steel sector vary from indicating an improvement to a decline in the sector's productivity. The variance may be traced to the time period of study, source of data for analysis, and type of indices and econometric specifications used for reporting productivity growth. The authors derive both growth accounting and econometric estimates of productivity growth for this sector. Their results show that over the observed period from 1973--74 to 1993--94 productivity declined by 1.71{percent} as indicated by the Translog index. Calculations of the Kendrick and Solow indices support this finding. Using a translog specification the econometric analysis reveals that technical progress in India's iron and steel sector has been biased towards the use of energy and material, while it has been capital and labor saving. The decline in productivity was caused largely by the protective policy regarding price and distribution of iron and steel as well as by large inefficiencies in public sector integrated steel plants. Will these trends continue into the future, particularly where energy use is concerned? Most likely they will not. The authors examine the current changes in structure and energy efficiency undergoing in the sector. Their analysis shows that with the liberalization of the iron and steel sector, the industry is rapidly moving towards world-best technology, which will result in fewer carbon emissions and more efficient energy use in existing and future plants.

  17. Prior thermo-mechanical processing to modify structure and properties of severely deformed low carbon steel

    NASA Astrophysics Data System (ADS)

    Zrnik, J.; Lapovok, R.; Raab, G. I.

    2014-08-01

    The article focuses on the severe plastic deformation (SPD) of low carbon steel AISI 1010 performed at increased temperature. The grain refinement of ferrite structure is monitored and described with respect to different initial steel structure modified by thermal and thermomechanical (TM) treatment (TM) prior severe plastic deformation. The refinement of coarse initial ferrite structure with grain size in range of 30 - 50 gm resulted from solutioning was conducted then in two steps. Preliminary structure refinement has been achieved due to multistep open die forging process and quite uniform ferrite structure with grain size of the order of gm was obtained. The further grain refinement steel structure was then accomplished during warm Equal Channel Angular Pressing (ECAP phi = 120°) at 300°C, introducing different strain in range of ɛef = 2.6 -4. The change of microstructure in dependence of the effective strain was evaluated by SEM and TEM study of thin foils. The high straining of steel resulted in extensive deformation of ferrite grains and formation of mixture of submicron grains structure in banded deformed structure with dense dislocation network and subgrains. The dynamic polygonization process, due to increased ECAP temperature, modified the submicrocrystalline structure formation. There was only indistinctive difference observed in structure refinement when considering different initial structure of steel. The tensile behaviour was characterized by strength increase followed by softening. None work hardening phenomenon appeared at tensile deformation of deformed bars.

  18. Crack-Growth Behavior of Laser Surface-Alloyed Low-Carbon Steel

    NASA Astrophysics Data System (ADS)

    Šturm, Roman; Žnidaršič, Matjaž; Grum, Janez

    2013-09-01

    Crack-growth behavior of Nd:YAG laser surface-alloyed as-received low-carbon steel Fe360B was evaluated. Thin surface layer was alloyed with silicon carbide SiC. During laser surface alloying process SiC powder dissolved in the melted pool. The surface-alloyed layer had as-solidified structure composed mainly of dendrites of ferrite, fine martensite needles, and retained austenite. The micro-hardness of the laser surface-alloyed layer was about 850 HV0.1. In laser surface-alloyed layer compressive residual stresses of average amount of σ RS = -100 MPa were obtained. In crack-growth tests comparison between specimens of as-received low-carbon steel Fe360B and the same steel with laser-alloyed surface was made. As the crack propagation was perpendicular to the interface between the laser-alloyed layers and the base metal, laser surface-alloyed specimens exhibited higher crack-growth resistance in the low stress intensity factor range Δ K th than as-received steel specimens.

  19. Mechanical behavior of ultrahigh strength ultrahigh carbon steel wire and rod

    SciTech Connect

    Lesuer, D.R.; Syn, C.K.; Sberby, O.D.; Whittenherger, W.D.

    1997-07-22

    Ultrahigh-carbon steels (UHCSS) can achieve very high strengths in wire or rod form. These high strengths result from the mechanical work introduced during wire and rod processing. These strengths have been observed to increase with carbon content. In wire form, tensile strengths approaching 6000 MPa are predicted for UHCS containing 1. 8%C. In this paper, we will discuss the influence of processing (including rapid transformation during wire patenting) and micros ct- ure on the mechanical behavior of UHCS wire. The tensile properties of as- extruded rods are described as a function of extrusion temperature and composition. For spheroidized steels, yield and ultimate tensile strength are a function of grain size, interparticle spacing and particle size. For pearlitic steels, yield and ultimate strength were found to be functions of colony size, carbide size and plate spacing and orientation. Alloying additions (such as C, Cr, Si, Al and Co) can influence the effect of processing on these microstructural features. For spheroidized steels, fracture was found to be a function of the size of coarse carbides and of composition.

  20. Protection of carbon steel against hot corrosion using thermal spray Si- and Cr-base coatings

    SciTech Connect

    Porcayo-Calderon, J.; Gonzalez-Rodriguez, J.G.; Martinez, L.

    1998-02-01

    A Fe75Si thermal spray coating was applied on the surface of a plain carbon steel baffle plate. Beneath this coating, a Ni20Cr coating was applied to give better adherence to the silicon coating. The baffle was installed in the high-temperature, fireside, corrosion zone of a steam generator. At the same time, an uncoated 304 stainless steel baffle was installed nearby for comparison. For 13 months the boiler burned heavy fuel oil with high contents of vanadium. The samples were studied employing scanning electron microscopy, x-ray microanalysis, and x-ray diffraction techniques. After that, it was possible to inspect the structural state of the components, and it was found that the stainless steel baffle plates were destroyed almost completely by corrosion, whereas the carbon steel coated baffle plate did not suffer a significant attack, showing that the performance of the thermal spray coating was outstanding and that the coating was not attacked by vanadium salts of the molten slag.

  1. Performance of heat-resistant silicon based coatings on plain carbon steel components in corrosive environments

    SciTech Connect

    Porcayo-Calderon, J.; Gonzalez-Rodriquez, J.G.; Martinez, L.

    1995-12-31

    A silicon based thermal spray coating was applied on the surface of a plain carbon steel baffle plate. The baffle was installed in the high temperature corrosion zone of a 350 MW boiler. At the same time, a 304 stainless steel baffle was installed nearby in order to compare the performance of the coating. During 13 month the boiler burnt heavy fuel oil with high contents of vanadium. After that, it was possible to inspect the structural state of the components, and it was found that the stainless steel baffle plates were destroyed, by corrosion almost completely (90% approximately). The carbon steel coated baffle plate practically did not suffer attack. The samples were studied employing scanning electron microscopy, X-ray microanalysis and X-ray diffraction, and the results shown that the coating was not attacked by vanadium salts of the molten slag. In addition nickel from the coating to the base metal, and iron from the base metal to the coating. The performance of the silicon based thermal spray coating was outstanding.

  2. Cr-Al coatings on low carbon steel prepared by a mechanical alloying technique

    NASA Astrophysics Data System (ADS)

    Hia, A. I. J.; Sudiro, T.; Aryanto, D.; Sebayang, K.

    2016-08-01

    Four different compositions of Cr and Al coatings as Cr10o, Cr87.5Al12.5, Cr5oAl5o, and Al100 have been prepared on the surface of low carbon steel by a mechanical alloying technique. The composition of each powder was milled for 2 hour in a stainless steel crucible with a ball to powder ratio of 10:1. Hereafter, the Cr-Al powder and substrate were mechanical alloyed in air for 1 hour. Heat treatment of coated sample were carried out at 800°C in a vacuum furnace. In order to characterize the phase composition and microstructure of the coating before and after heat treatment, XRD and SEM-EDX were used. The results show that Cr, Cr-Al or Al coatings were formed on the surface of low carbon steel. After heat treatment, new phases and interdiffusion zone were formed in the coating and at the coating/steel interface, depending on the coating composition.

  3. Phase Evolution in Boride-Based Cermets and Reaction Bonding onto Plain Low Carbon Steel Substrate

    NASA Astrophysics Data System (ADS)

    Palanisamy, B.; Upadhyaya, A.

    2012-04-01

    Reaction sinter bonding is a process that aims to bond two materials for improvement in properties through reactive sintering technique. The process has been effectively used to sinter hard materials like borides in situ which not only possess excellent oxidation resistance, good corrosion resistance but also resistant to abrasive wear. Sinter bonding is a unique surface modification process achieved through powder metallurgy and is competent with other techniques like boronizing sintering and sinter-brazing since it eliminates the additional operations of heat treatment and assembly and removes the inherent setbacks with these processes. This study focuses on identifying the phase evolution mechanism using characterization tools like x-ray diffractometry and energy dispersive spectroscopy and study of sinter bonding of the boron containing precursors (Mo-Cr-Fe-Ni-FeB-MoB) onto plain carbon steel. A microstructure containing Fe-based matrix dispersed with complex borides develops with temperature in the tape cast sheets. A fivefold increase in hardness between plain carbon steel in wrought condition and sinter bonded steel was observed. The multilayer consisted of a reaction zone adjacent to the interface and was investigated with the composition profile and hardness measurements. A model of sinter bonding between the cermet and the steel has also been proposed.

  4. HYDROTHERMALLY SELF-ADVANCING HYBRID COATINGS FOR MITIGATING CORROSION OF CARBON STEEL.

    SciTech Connect

    SUGAMA, T.

    2006-11-22

    Hydrothermally self-advancing hybrid coatings were prepared by blending two starting materials, water-borne styrene acrylic latex (SAL) as the matrix and calcium aluminate cement (CAC) as the hydraulic filler, and then their usefulness was evaluated as the room temperature curable anti-corrosion coatings for carbon steel in CO{sub 2}-laden geothermal environments at 250 C. The following two major factors supported the self-improving mechanisms of the coating during its exposure in an autoclave: First was the formation of a high temperature stable polymer structure of Ca-complexed carboxylate groups containing SAL (Ca-CCG-SAL) due to hydrothermal reactions between SAL and CAC; second was the growth with continuing exposure time of crystalline calcite and boehmite phases coexisting with Ca-CCG-SAL. These two factors promoted the conversion of the porous microstructure in the non-autoclaved coating into a densified one after 7 days exposure. The densified microstructure not only considerably reduced the conductivity of corrosive ionic electrolytes through the coatings' layers, but also contributed to the excellent adherence of the coating to underlying steel' s surface that, in turn, retarded the cathodic oxygen reduction reaction at the corrosion site of steel. Such characteristics including the minimum uptake of corrosive electrolytes by the coating and the retardation of the cathodic corrosion reaction played an important role in inhibiting the corrosion of carbon steel in geothermal environments.

  5. Tensile and impact behavior of laminated composites based on ultrahigh carbon steel

    SciTech Connect

    Lee, S.

    1988-01-01

    The goal was to develop metal-laminated composites for high strength and high strength and high toughness and centered on three major objectives. The first one was to develop a laminated composite, based on ultrahigh carbon steel (UHCS), which can be selectively heat treated to achieve alternating hard UHCS and soft interleaf layers. The second was to maintain sharp and discrete interlayer boundaries in the UHCS laminated composite after selective heat treatment with no interdiffusion of carbon. The third was to achieve high notch-impact toughness in the selectively heat-treated laminated composite. Five laminated composites were investigated. They are UHCS/Fe-3%Si, UHCS/Hadfield manganese steel (HMS), UHCS/9%Ni-2%Si steel, UHCS/brass and UHCS/304 stainless steel (304ss). All five laminated composites were selectively heat treated to achieve the desired objective of alternating hard and soft layers. Charpy V-notch impact tests were performed on the first four laminates. Each laminate showed a lower ductile-to-brittle transition temperature (DBTT) than those obtained in the monolithic UHS and the monolithic interleaf material making up the laminate.

  6. Effects of thin-film accelerated carbonation on steel slag leaching.

    PubMed

    Baciocchi, R; Costa, G; Polettini, A; Pomi, R

    2015-04-09

    This paper discusses the effects of accelerated carbonation on the leaching behaviour of two types of stainless steel slags (electric arc furnace and argon oxygen decarburisation slag). The release of major elements and toxic metals both at the natural pH and at varying pH conditions was addressed. Geochemical modelling of the eluates was used to theoretically describe leaching and derive information about mineralogical changes induced by carbonation. Among the investigated elements, Ca and Si were most appreciably affected by carbonation. A very clear effect of carbonation on leaching was observed for silicate phases; geochemical modelling indicated that the Ca/Si ratio of Ca-controlling minerals shifted from ∼ 1 for the untreated slag to 0.5-0.67 for the carbonated samples, thus showing that the carbonation process left some residual Ca-depleted silicate phases while the extracted Ca precipitated in the form of carbonate minerals. For toxic metals the changes in leaching induced by carbonation appeared to be mainly related to the resulting pH changes, which were as high as ∼ 2 orders of magnitude upon carbonation. Depending on the specific shape of the respective solubility curves, the extent of leaching of toxic metals from the slag was differently affected by carbonation.

  7. Carbon concentration measurements by atom probe tomography in the ferritic phase of high-silicon steels

    SciTech Connect

    Rementeria, Rosalia; Poplawsky, Jonathan D.; Aranda, Maria M.; Guo, Wei; Jimenez, Jose A.; Garcia-Mateo, Carlos; Caballero, Francisca G.

    2016-12-19

    Current studies using atom probe tomography (APT) show that bainitic ferrite formed at low temperature contains more carbon than what is consistent with the paraequilibrium phase diagram. However, nanocrystalline bainitic ferrite exhibits a non-homogeneous distribution of carbon atoms in arrangements with specific compositions, i.e. Cottrell atmospheres, carbon clusters, and carbides, in most cases with a size of a few nanometers. The ferrite volume within a single platelet that is free of these carbon-enriched regions is extremely small. Proximity histograms can be compromised on the ferrite side, and a great deal of care should be taken to estimate the carbon content in regions of bainitic ferrite free from carbon agglomeration. For this purpose, APT measurements were first validated for the ferritic phase in a pearlitic sample and further performed for the bainitic ferrite matrix in high-silicon steels isothermally transformed between 200 °C and 350 °C. Additionally, results were compared with the carbon concentration values derived from X-ray diffraction (XRD) analyses considering a tetragonal lattice and previous APT studies. In conclusion, the present results reveal a strong disagreement between the carbon content values in the bainitic ferrite matrix as obtained by APT and those derived from XRD measurements. Those differences have been attributed to the development of carbon-clustered regions with an increased tetragonality in a carbon-depleted matrix.

  8. Carbon concentration measurements by atom probe tomography in the ferritic phase of high-silicon steels

    DOE PAGES

    Rementeria, Rosalia; Poplawsky, Jonathan D.; Aranda, Maria M.; ...

    2016-12-19

    Current studies using atom probe tomography (APT) show that bainitic ferrite formed at low temperature contains more carbon than what is consistent with the paraequilibrium phase diagram. However, nanocrystalline bainitic ferrite exhibits a non-homogeneous distribution of carbon atoms in arrangements with specific compositions, i.e. Cottrell atmospheres, carbon clusters, and carbides, in most cases with a size of a few nanometers. The ferrite volume within a single platelet that is free of these carbon-enriched regions is extremely small. Proximity histograms can be compromised on the ferrite side, and a great deal of care should be taken to estimate the carbon contentmore » in regions of bainitic ferrite free from carbon agglomeration. For this purpose, APT measurements were first validated for the ferritic phase in a pearlitic sample and further performed for the bainitic ferrite matrix in high-silicon steels isothermally transformed between 200 °C and 350 °C. Additionally, results were compared with the carbon concentration values derived from X-ray diffraction (XRD) analyses considering a tetragonal lattice and previous APT studies. In conclusion, the present results reveal a strong disagreement between the carbon content values in the bainitic ferrite matrix as obtained by APT and those derived from XRD measurements. Those differences have been attributed to the development of carbon-clustered regions with an increased tetragonality in a carbon-depleted matrix.« less

  9. Influence of hydrogen-oxidizing bacteria on the corrosion of low carbon steel: Local electrochemical investigations.

    PubMed

    Moreira, Rebeca; Schütz, Marta K; Libert, Marie; Tribollet, Bernard; Vivier, Vincent

    2014-06-01

    Low carbon steel has been considered a suitable material for component of the multi-barrier system employed on the geological disposal of high-level radioactive waste (HLW). A non negligible amount of dihydrogen (H2) is expected to be produced over the years within the geological repository due to the anoxic corrosion of metallic materials and also to the water radiolysis. The influence of the activity of hydrogen-oxidizing bacteria (HOB) and iron-reducing bacteria (IRB) on carbon steel corrosion is considered in this study because of the high availability of energetic nutriments (H2, iron oxides and hydroxides) produced in anoxic disposal conditions. Local electrochemical techniques were used for investigating the activity of IRB as a promoter of local corrosion in the presence of H2 as electron donor. A local consumption of H2 by the bacteria has been evidenced and impedance measurements indicate the formation of a thick layer of corrosion products.

  10. Carbon recovery by fermentation of CO-rich off gases - Turning steel mills into biorefineries.

    PubMed

    Molitor, Bastian; Richter, Hanno; Martin, Michael E; Jensen, Rasmus O; Juminaga, Alex; Mihalcea, Christophe; Angenent, Largus T

    2016-09-01

    Technological solutions to reduce greenhouse gas (GHG) emissions from anthropogenic sources are required. Heavy industrial processes, such as steel making, contribute considerably to GHG emissions. Fermentation of carbon monoxide (CO)-rich off gases with wild-type acetogenic bacteria can be used to produce ethanol, acetate, and 2,3-butanediol, thereby, reducing the carbon footprint of heavy industries. Here, the processes for the production of ethanol from CO-rich off gases are discussed and a perspective on further routes towards an integrated biorefinery at a steel mill is given. Recent achievements in genetic engineering as well as integration of other biotechnology platforms to increase the product portfolio are summarized. Already, yields have been increased and the portfolio of products broadened. To develop a commercially viable process, however, the extraction from dilute product streams is a critical step and alternatives to distillation are discussed. Finally, another critical step is waste(water) treatment with the possibility to recover resources.

  11. Spectroscopic investigation of plasma electrolytic borocarburizing on q235 low-carbon steel

    NASA Astrophysics Data System (ADS)

    Liu, Run; Wang, Bin; Wu, Jie; Xue, Wenbin; Jin, Xiaoyue; Du, Jiancheng; Hua, Ming

    2014-12-01

    A plasma electrolytic borocarburizing process (PEB/C) in borax electrolyte with glycerin additive was employed to fabricate a hardening layer on Q235 low-carbon steel. Optical emission spectroscopy (OES) was utilized to investigate the spectroscopy characteristics of plasma discharge around the steel during PEB/C process. Some plasma parameters were calculated in terms of OES. The electron temperature and electron concentration in plasma discharge zone is about 3000-12,000 K and 2 × 1022 m-3-1.4 × 1023 m-3. The atomic ionization degrees of iron, carbon and boron are 10-16-10-3, and 10-23-10-6, 10-19-10-4, respectively, which depend on discharge time. The surface morphology and cross-sectional microstructure of PEB/C hardening layer were observed, and the electrolyte decomposition and plasma discharge behaviors were discussed.

  12. Using Phased Array Ultrasonic Testing in Lieu of Radiography for Acceptance of Carbon Steel Piping Welds

    SciTech Connect

    Moran, Traci L.; Anderson, Michael T.; Cinson, Anthony D.; Crawford, Susan L.; Nove, Carol A.

    2014-08-01

    The Pacific Northwest National Laboratory (PNNL) is conducting studies for the U.S. Nuclear Regulatory Commission (NRC) to assess the capability, effectiveness, and reliability of ultrasonic testing (UT) as a replacement method for radiographic testing (RT) for volumetric examination of nuclear power plant (NPP) components. This particular study focused on evaluating the use of UT on carbon steel plate welds. Welding fabrication flaws included a combination of planar and volumetric types, e.g., incomplete fusion, lack of penetration, cracks, porosity, and slag inclusions. The examinations were conducted using phased-array (PA) UT techniques applied primarily for detection and flaw type characterization. This paper will discuss the results of using UT in lieu of RT for detection and classification of fabrication flaws in carbon steel plate welds.

  13. Bacterial adhesion to diamond-like carbon as compared to stainless steel.

    PubMed

    Soininen, Antti; Tiainen, Veli-Matti; Konttinen, Yrjö T; van der Mei, Henny C; Busscher, Henk J; Sharma, Prashant K

    2009-08-01

    Recent studies suggest that diamond-like carbon (DLC) coatings are suitable candidates for application on biomedical devices and implants, due to their high hardness, low friction, high wear and corrosion resistance, chemical inertness, smoothness, and tissue and blood compatibility. However, most studies have neglected the potential susceptibility of DLC coatings to bacterial adhesion, which is the first step in the development of implant-related infections. This study compares adhesion of seven bacterial strains, commonly implicated in implant-related infections, to tetrahedral amorphous carbon, with their adhesion to AISI 316L surgical steel. The results show that bacterial adhesion to DLC was similar to the adhesion to commonly used stainless steel. This suggests that DLC coating can be advantageously used on implants made of AISI 316L or other materials without increasing the risk to implant-related infections.

  14. Effect of silty sand in formation water on CO2 corrosion behavior of carbon steel

    NASA Astrophysics Data System (ADS)

    Liu, Wei; Dou, Juanjuan; Lu, Songle; Zhang, Peng; Zhao, Qinghe

    2016-03-01

    Corrosion behavior of carbon steel in CO2 aqueous environment containing silty sand was investigated using corrosion mass loss method, scanning electron microscopy (SEM), energy diffraction spectrum (EDS), and various electrochemical measurements. The results show that the corrosion rate of carbon steel was obviously reduced due to the existence of silty sand. Silty sand promoted the rapid heterogeneous nucleation of corrosion product FeCO3 and simultaneously decreased its grains growth. Silty sand mixed with corrosion product to form the outer layer of corrosion scale with high compactness, blocking the transport of ferrous ions and leading to the formation of the inner layer of corrosion scale without silty sand. The existence of silty sand in the outer layer of corrosion scale inhibited anodic and cathodic currents.

  15. Enhancement of corrosion resistance of carbon steel by Dioscorea Hispida starch in NaCl

    NASA Astrophysics Data System (ADS)

    Zulhusni, M. D. M.; Othman, N. K.; Lazim, Azwan Mat

    2015-09-01

    Starch is a one of the most abundant natural product in the world and has the potential as corrosion inhibitor replacing harmful synthetic chemical based corrosion inhibitor. This research was aimed to examines the potential of starch extracted from local Malaysian wild yam (Dioscorea hispida), as corrosion inhibitor to carbon steel in NaCl media replicating sea water. By using gravimetric test and analysis, in which the carbon steel specimens were immersed in NaCl media for 24, 48 and 60 hours with the starch as corrosion inhibitor. the corrosion rate (mmpy) and inhibition efficiencies (%) was calculated. The results obtained showed decrease in corrosion rate as higher concentration of starch was employed. The inhibition efficiencies also shows an increasing manner up to 95.97 % as the concentration of the inhibitor increased.

  16. Orientation changes near the interface of explosively bonded (carbon steel)/Zr700 sheets

    NASA Astrophysics Data System (ADS)

    Paul, H.; Baudin, T.; Brisset, F.; Prazmowski, M.

    2015-04-01

    The microstructure and texture of explosively welded carbon steel (base) and Zr700 (flyer) plates were characterized by means of scanning electron microscopy equipped with a high resolution electron backscattered diffraction facility. The orientation maps demonstrate that the deformed zones near-the-interface are composed of several layers, the width of which depends on the applied bonding parameters. For both metals, the very thin layer of ultra-fine grains directly adheres to the interface. In the areas more distanced from the interface, the structure evolution depends on the plate material. In the case of a Zr 700 sheet the second layer is formed by highly dislocated (sub)grains, which progressively evolve, towards the structure composed of only lightly deformed grains. In the case of a carbon steel sheet, the second layer near the interface was composed of flattened grains.

  17. Low temperature superplasticity and thermal stability of a nanostructured low-carbon microalloyed steel

    PubMed Central

    Hu, J.; Du, L.-X.; Sun, G.-S.; Xie, H.; Misra, R.D.K.

    2015-01-01

    We describe here for the first time the low temperature superplasticity of nanostructured low carbon steel (microalloyed with V, N, Mn, Al, Si, and Ni). Low carbon nanograined/ultrafine-grained (NG/UFG) bulk steel was processed using a combination of cold-rolling and annealing of martensite. The complex microstructure of NG/UFG ferrite and 50–80 nm cementite exhibited high thermal stability at 500 °C with low temperature elongation exceeding 100% (at less than 0.5 of the absolute melting point) as compared to the conventional fine-grained (FG) counterpart. The low temperature superplasticity is adequate to form complex components. Moreover, the low strength during hot processing is favorable for decreasing the spring back and minimize die loss. PMID:26687012

  18. Low temperature superplasticity and thermal stability of a nanostructured low-carbon microalloyed steel

    NASA Astrophysics Data System (ADS)

    Hu, J.; Du, L.-X.; Sun, G.-S.; Xie, H.; Misra, R. D. K.

    2015-12-01

    We describe here for the first time the low temperature superplasticity of nanostructured low carbon steel (microalloyed with V, N, Mn, Al, Si, and Ni). Low carbon nanograined/ultrafine-grained (NG/UFG) bulk steel was processed using a combination of cold-rolling and annealing of martensite. The complex microstructure of NG/UFG ferrite and 50-80 nm cementite exhibited high thermal stability at 500 °C with low temperature elongation exceeding 100% (at less than 0.5 of the absolute melting point) as compared to the conventional fine-grained (FG) counterpart. The low temperature superplasticity is adequate to form complex components. Moreover, the low strength during hot processing is favorable for decreasing the spring back and minimize die loss.

  19. Effect of Carbon Steel Composition and Microstructure on CO2 Corrosion

    NASA Astrophysics Data System (ADS)

    Akeer, Emad S.

    The environmental conditions encountered in oil and gas wells and pipelines can cause severe localized corrosion to mild steel. The utility of carbon steel in oil and gas pipelines depends on formation of protective corrosion product layers. However, the microstructure and chemical composition of steel are considered to be important variables that affect the ability of these layers to protect steel from corrosion. The present study investigated the effect of alloying elements and metallurgy of five different pipeline steels, with different chemical composition and microstructure, on CO2 corrosion in flowing conditions with focus on the iron carbonate layer formed and related corrosion phenomena that could lead to localized corrosion. The microstructure of tested steels was examined using optical microscopy and etching. Preliminary experiments were conducted using a glass cell, which is a very well known and widely used apparatus. Then a comparison was done with the newly developed thin channel flow cell (TCFC) to validate whether the TCFC can be used instead of glass cell in this study, which required very high velocity and wall shear stresses. It was found that there are no significant effects of alloying elements and steel microstructure on corrosion rate in experiments done at pH 4.0 at 25°C and 80°C. Further experiments were then conducted in the TCFC to study the effect of alloying elements and microstructure under conditions where a protective FeCO3 4 corrosion product layer forms, using very high liquid flow rates. For each of the studied steels, an FeCO3 corrosion product layer was formed within two days of exposure at low wall shear stress at 80°C, pH 6.6, and partial pressure of CO2 of 1.5 bar (1.5 bar pCO 2). For all tested steels, the FeCO3 layer reduced the general corrosion rate to less than 1.0 mm/y. These "pre-formed" FeCO3 layers were then exposed to high liquid flow velocity and wall shear stress (535 Pa) for 3 days. This caused partial loss of

  20. Fretting Wear Mechanisms in A216 Plain Carbon Steel

    NASA Astrophysics Data System (ADS)

    Maich, Alyssa Anne

    The subsurface and surface microstructures during pin-on-disk fretting wear of A216 steel disks under various loading conditions and times are investigated. The corresponding pins are fabricated from 410 stainless steel to simulate in-service conditions found in such engineering components as the Siemens W501FD engine row-2 diaphragm of a Siemens turbine engine, which is known to be prone to failure by fretting wear. Loading conditions range from 2N to 15N and times from 1 hour to a maximum of 69 hours, when steady state is confirmed. Wear track depth is quantitatively determined by optical profilometry, and found to range from 3 to 11 microns dependent upon load. Wear depth increases from 2N to 10N load, but decreases when increased to 15N load, due to heavier transfer of pin material to disk, as can be seen by EDS images of chromium transfer on A216 disk. Microstructures are evaluated by transmission electron microscopy of samples prepared by focused ion beam machining to pinpoint wear tracks and expose them in cross-section. EDS is used, in conjunction with TEM, to elucidate primary wear mechanisms at each stage of fretting wear. Microstructures in the subsurface of wear tracks are found to be heavily dislocated and layered, features that vary with both applied load and time. The microstructure eventually evolves into stable dislocation cells with cell walls aligned parallel to the surface. Penetration depth of the damaged layers increases with applied load, associated with a non-uniform maximum shear stress distribution that varies with depth. Primary oxide appears to evolve from Fe2O3 to Fe3O4, with increasing fretting time, leading to a uniform oxide on the surface of the A216 disk. Oxidation rate may be increased with the evolution of this subsurface dislocation cell structure. It is concluded that fretting wear failure is likely associated with a synergy between oxidative wear and crack initiation and propagation along dislocation cell walls under high

  1. Texture evolution in warm rolled low-carbon steels

    NASA Astrophysics Data System (ADS)

    Sanchez Araiza, Miguel

    The effect of warm and cold rolling parameters on the development of annealing textures and their effects on the final formability were studied in two LC steels containing 0.8%Cr. Warm rolling temperatures between 640 and 750°C were employed, together with reductions of 65% to 80%. The effects of an additional cold rolling reduction of 40%, different initial hot band grain sizes (HBGSs) and a decrease in the heating rate during annealing were also studied. The ND fibre, <111>//ND, of the recrystallization texture was strengthened as the warm rolling temperature was decreased. A noticeable improvement in both the continuity and intensity of the ND fibre was obtained when samples were submitted to an additional 40% cold rolling reduction. The ND fibre was even more continuous and intense when a low heating rate was utilized, yielding r-values of 1.2 and 1.3 for the warm rolled and warm plus cold rolled samples, respectively. On the other hand, the volume fraction of grains containing shear bands is slightly lower for the finer HBGS. However, this does not reduce the amount of in-grain nucleation of gamma grains, suggesting that shear bands are not the only factor that has to be considered in the improvement of warm rolling textures. Although the normal anisotropy is not affected by the HBGS, much lower Deltar values were associated with the finer grained steel. The texture changes taking place during recrystallization were examined using electron back-scattered diffraction. The recrystallization textures resemble the deformation textures but with a more extensive alpha fibre that includes the {113}<471> orientation; the gamma fibre extends to the {554}<225>. These two orientations are related to the {112}<110> deformed grains by near 26° rotations about selected <110> axes. Nevertheless, both orientations appear in the early stages of recrystallization, an observation that does not support the oriented growth theory. The {111} < hkl> orientations are the first to

  2. A method for predicting service life of zinc rich primers on carbon steel

    NASA Technical Reports Server (NTRS)

    Hoppesch, C. W.

    1986-01-01

    The service life of zinc rich primers on carbon steel can be estimated by immersing a primer coated glass slide into an aqueous copper sulfate solution and measuring the amount of zinc that reacts with the copper in 15 minutes. This zinc availability test was used to evaluate eleven primers currently available for which marine beach exposure data was available from previous programs. Results were evaluated and a correlation between zinc availability and ASTM rust grade was shown.

  3. Mechanism of Pitting Corrosion Prevention by Nitrite in Carbon Steel Exposed to Dilute Salt Solutions

    SciTech Connect

    Philip E. Zapp; John W. Van Zee

    2002-02-01

    The research has developed a broad fundamental understanding of the inhibition action of nitrite ions in preventing nitrate pitting corrosion of carbon steel tanks containing high-level radioactive waste. This fundamental understanding can be applied to specific situations during waste removal for permanent disposition and waste tank closure to ensure that the tanks are maintained safely. The results of the research provide the insight necessary to develop solutions that prevent further degradation.

  4. Magnetic-field-induced grain elongation in a medium carbon steel during its austenitic decomposition

    SciTech Connect

    Zhang, Y.D.; Esling, C.; Muller, J.; He, C.S.; Zhao, X.; Zuo, L.

    2005-11-21

    A 12-T magnetic field was applied during the austenitic decomposition in a medium plain carbon steel at a slow cooling rate. The magnetic field applied promotes proeutectoid ferrite grains to grow along the field direction and results in an elongated grain microstructure. The grain elongation is the result of the opposing contributions from the atomic dipolar interaction energy of Fe atoms and the interfacial energy.

  5. Analysis of Wood Structure Connections Using Cylindrical Steel and Carbon Fiber Dowel Pins

    NASA Astrophysics Data System (ADS)

    Vodiannikov, Mikhail A.; Kashevarova, Galina G., Dr.

    2017-06-01

    In this paper, the results of the statistical analysis of corrosion processes and moisture saturation of glued laminated timber structures and their joints in corrosive environment are shown. This paper includes calculation results for dowel connections of wood structures using steel and carbon fiber reinforced plastic cylindrical dowel pins in accordance with applicable regulatory documents by means of finite element analysis in ANSYS software, as well as experimental findings. Dependence diagrams are shown; comparative analysis of the results obtained is conducted.

  6. Gas tungsten arc and low hydrogen shielded metal arc welding of carbon steel. Welding procedure specification

    SciTech Connect

    Wodtke, C.H.; Frizzell, D.R.; Plunkett, W.A.

    1985-08-01

    Procedure WPS-128-ASME-1 is qualified under Section IX of the ASME Boiler and Pressure Vessel Code for gas tungsten arc and low hydrogen shielded metal arc welding of carbon steels (P-1-1), in thickness range 0.25 to 2 inch; filler metals are ER70S-3 (F-6, A-1) (GTAW) and E7018 (F-4, A-1); shielding gas is argon (GTAW).

  7. Manual gas tungsten arc and semiautomatic gas metal arc welding of carbon steel. Welding procedure specification

    SciTech Connect

    Wodtke, C.H.; Frizzell, D.R.; Plunkett, W.A.

    1985-08-01

    Procedure WPS-107-ASME-1 is qualified under Section IX of the ASME Boiler and Vessel Code for manual gas tungsten arc and semiautomatic gas metal arc welding of carbon steel (P-1-1), in thickness range 0.237 to 2.0 inch; filler metal is ER70S-3 (F-6, A-1); shielding gas for GTAW is argon, and for GMAW is 95-5 argon-oxygen.

  8. Welding procedure specification: gas tungsten arc and shielded metal arc welding of carbon steel

    SciTech Connect

    Wodtke, C.H.; Frizzell, D.R.; Plunkett, W.A.

    1985-08-01

    Procedure WPS-104-ASME-2 is qualified under Section IX of the ASME Boiler and Pressure Vessel Code for gas tungsten arc and shielded metal arc welding of carbon steels (P-1-1), in thickness range 0.25 to 1 in.; filler metals are E70S-3 (F-6, A-1) (GTAW) and E6010 (F-3, A-1) (SMAW); shielding gas is argon (GTAW).

  9. Effects Of Milling On Surface Integrity Of Low-Carbon Steel

    SciTech Connect

    Rodrigues, Alessandro Roger; Matsumoto, Hidekasu; Yamakami, Wyser Jose; Tokimatsu, Ruis Camargo; Menezes, Miguel Angelo; Suyama, Daniel Iwao; Norcino, Adriana Bruno; Vendrame, Saimon

    2011-01-17

    This work measured the effect of milling parameters on the surface integrity of low-carbon alloy steel. The Variance Analysis showed that only depth of cut did not influence on the workpiece roughness and the Pearson's Coefficient indicated that cutting speed was more influent than tool feed. All cutting parameters introduced tensile residual stress in workpiece surface. The chip formation mechanism depended specially on cutting speed and influenced on the roughness and residual stress of workpiece.

  10. Study of benzotriazole as corrosion inhibitors of carbon steel in chloride solution containing hydrogen sulfide using electrochemical impedance spectroscopy (EIS)

    SciTech Connect

    Solehudin, Agus; Nurdin, Isdiriayani

    2014-03-24

    Corrosion and inhibition studies on API 5LX65 carbon steel in chloride solution containing various concentrations of benzotriazole has been conducted at temperature of 70°C using Electrochemical Impedance Spectroscopy (EIS). Corroded carbon steel surface with and without inhibitor have been observed using X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), and Energy Dispersive Spectroscopy (EDS). The objectives of this research are to study the performance of benzotriazole as corrosion inhibitors. The experimental results of carbon steel corrosion in 3.5% NaCl solution containing 500 mg/l H{sub 2}S at different BTAH concentrations showed that corrosion rate of carbon steel decreases with increasing of BTAH concentrations from 0 to 10 mmol/l. The inhibition efficiency of BTAH was found to be affected by its concentration. The optimum efficiency obtained of BTAH is 93% at concentration of 5 mmol/l. The result of XRD and EDS analysis reveal the iron sulfide (FeS) formation on corroded carbon steel surface without inhibitor. The EDS spectrum show the Nitrogen (N) bond on carbon steel surface inhibited by BTAH.

  11. The corrosion of carbon steel in rock microcosms containing native Yucca Mountain microorganisms

    SciTech Connect

    Castro, P.R.; Amy, P.S.; Crossen, H.V.; Jones, D.A.; Southam, G.; Donald, R.; Ringelberg, D.B.

    1998-12-31

    Microorganisms implicated in microbially-influenced corrosion were isolated from the deep subsurface at Yucca Mountain, and include iron-oxidizing (FeOx), sulfate-reducing (SRB), and exopolysaccharide (EPS)-producing bacterial species. Various combinations of these microorganisms were inoculated into a test system composed of a 1020 carbon steel coupon immersed in a mixture of sterile rock and soft R2A agar prepared with simulated groundwater. A 1% KC1 bridge was used to connect the test system to a calomel reference electrode. A platinum counter electrode was used to apply a potential and the corrosion rate was measured by polarization resistance. Prior studies at ambient and elevated (50 C) temperatures demonstrated that these microorganisms were capable of corroding carbon steel. The current research investigated whether the presence of a rock surface enhanced the ability of the test microorganisms to survive elevated temperature and corrode carbon steel. Uninoculated electrochemical cells were prepared to monitor abiotic corrosion. Initial and weekly corrosion rates were obtained for the duration of the experiment. Upon completion of the experiment, the test system was dismantled and the coupons prepared for phospholipid fatty acid and microscopic analyses, to assess microbial biomass and biofilm formation, respectively. Increased biomass and higher corrosion rates were observed in the rock/agar microcosms.

  12. Effects of chloride ions on corrosion of ductile iron and carbon steel in soil environments.

    PubMed

    Song, Yarong; Jiang, Guangming; Chen, Ying; Zhao, Peng; Tian, Yimei

    2017-07-31

    Chloride is reported to play a significant role in corrosion reactions, products and kinetics of ferrous metals. To enhance the understanding of the effects of soil environments, especially the saline soils with high levels of chloride, on the corrosion of ductile iron and carbon steel, a 3-month corrosion test was carried out by exposing ferrous metals to soils of six chloride concentrations. The surface morphology, rust compositions and corrosion kinetics were comprehensively studied by visual observation, scanning electron microscopy (SEM), X-Ray diffraction (XRD), weight loss, pit depth measurement, linear polarization and electrochemical impedance spectroscopy (EIS) measurements. It showed that chloride ions influenced the characteristics and compositions of rust layers by diverting and participating in corrosion reactions. α-FeOOH, γ-FeOOH and iron oxides were major corrosion products, while β-Fe8O8(OH)8Cl1.35 rather than β-FeOOH was formed when high chloride concentrations were provided. Chloride also suppressed the decreasing of corrosion rates, whereas increased the difficulty in the diffusion process by thickening the rust layers and transforming the rust compositions. Carbon steel is more susceptible to chloride attacks than ductile iron. The corrosion kinetics of ductile iron and carbon steel corresponded with the probabilistic and bilinear model respectively.

  13. Combined geochemical and electrochemical methodology to quantify corrosion of carbon steel by bacterial activity.

    PubMed

    Schütz, Marta K; Moreira, Rebeca; Bildstein, Olivier; Lartigue, Jean-Eric; Schlegel, Michel L; Tribollet, Bernard; Vivier, Vincent; Libert, Marie

    2014-06-01

    The availability of respiratory substrates, such as H2 and Fe(II,III) solid corrosion products within nuclear waste repository, will sustain the activities of hydrogen-oxidizing bacteria (HOB) and iron-reducing bacteria (IRB). This may have a direct effect on the rate of carbon steel corrosion. This study investigates the effects of Shewanella oneidensis (an HOB and IRB model organism) on the corrosion rate by looking at carbon steel dissolution in the presence of H2 as the sole electron donor. Bacterial effect is evaluated by means of geochemical and electrochemical techniques. Both showed that the corrosion rate is enhanced by a factor of 2-3 in the presence of bacteria. The geochemical experiments indicated that the composition and crystallinity of the solid corrosion products (magnetite and vivianite) are modified by bacteria. Moreover, the electrochemical experiments evidenced that the bacterial activity can be stimulated when H2 is generated in a small confinement volume. In this case, a higher corrosion rate and mineralization (vivianite) on the carbon steel surface were observed. The results suggest that the mechanism likely to influence the corrosion rate is the bioreduction of Fe(III) from magnetite coupled to the H2 oxidation.

  14. Effect of Prestrain Type on the Rotating Bending Fatigue Limit of Carbon Steel

    NASA Astrophysics Data System (ADS)

    Kang, Minwoo; Aono, Yuuta; Noguchi, Hiroshi

    The effect of the type of prestrain (tensile or torsional prestrain) on the fatigue limit of carbon steel was investigated. Annealed 0.1%, annealed 0.5%, and quenched and tempered 0.5% carbon steel specimens were subjected to monotonically tension or torsion to produce plastic strain. Fatigue tests were performed using rotating bending fatigue test machines (R=-1). The results of experiments showed that the fatigue limit of the torsional-prestrained specimen was higher than that of the tensile-prestrained specimen and the degree of cyclic softening induced by fatigue loading in the torsional-prestrained specimen was lower than that in the tensile-prestrained specimen. The results mean that the effect of the prestrain type on the fatigue limit is related to the cyclic softening and the cyclic softening depends on the relationship between prestrain type and fatigue-loading type. However, the effect was small when there is precrack formed by prestraining or artificial defect on the specimen. A method of predicting the fatigue limit of prestrained carbon steels was also discussed on the basis of the results.

  15. Fatigue Life and Crack Growth Behavior in Annealed and Normalized 0.83% Carbon Steel

    NASA Astrophysics Data System (ADS)

    Makabe, Chobin; Yamazaki, Shinya; Miyazaki, Tatsujiro; Fujikawa, Masaki

    2015-09-01

    The variations of fatigue limit and fatigue life of a plain specimen of annealed and normalized 0.83% carbon steel were investigated. This material is used for cutting tools and the original microstructure includes a spherical microstructure. After heat treatment under some conditions, the microstructure changed to a lamellar microstructure. However, the fatigue lives of the plain specimens of this material showed almost the same tendency even after heat treatment under some conditions. In those cases, the initial crack length in the fatigue process is related to the size of the crystal structure and related to the distribution of ferrite. In the present study, the relationship between the distribution of hardness and the fatigue limit was investigated. Also, it was discussed that the fatigue limit of heat-treated 0.83% carbon steel could be evaluated by a relationship in which the parameters are the hardness and initial crack length. Finally, the tendencies of fatigue life of heat-treated 0.83% carbon steel were discussed based on the observations of crack growth behavior.

  16. Effects of Mo ion implantation on rolling contact fatigue behavior of carbon steel

    SciTech Connect

    Yang, D.; Zhou, J.

    1996-11-01

    Rolling Contact Fatigue (RCF) is one of the most serious material surface damage problems encountered by many critical components, especially in ball-bearing applications. RCF is sensitive to the material strength, hardness, surface morphology, microstructure and stress status, which may be dramatically changed by surface modifications. In present work, the surface modification of molybdenum ion implantation into quenched carbon steel was employed, and RCF tests on the implanted specimens, as well as the unimplanted, were performed. It was found out that carbon steel specimens, with and without ion implantation, have the same fatigue damage characteristics. They both have circular and fan-like pits on the fatigue failed surfaces, with many spherical debris existing in the fan-like pits. However, molybdenum ion implantation reduced the rolling contact fatigue life of quenched carbon steel. The possible reasons are the following: the ion beam current is too large, which causes the specimen to undergo the annealing process and soften during the implantation process; the incident angles of ions are different for different spots of curve specimen surface, which causes the uneven distribution of residual stress. These will promote the crack initiation and propagation.

  17. Formation of Diffusion Layers by Anode Plasma Electrolytic Nitrocarburizing of Low-Carbon Steel

    NASA Astrophysics Data System (ADS)

    Kusmanov, S. A.; Kusmanova, Yu. V.; Naumov, A. R.; Belkin, P. N.

    2015-08-01

    The structure of the low-carbon steel after plasma electrolytic nitrocarburizing in the electrolyte containing acetonitrile was investigated. The cross-sectional microstructure, composition, and phase constituents of a modified layer under different processing conditions were characterized. It is shown that the electrolyte that contained ammonium chloride and acetonitrile provides the saturation of steel with nitrogen and carbon and the formation of the Fe4N and FeN0.05 nitrides, Fe4C carbide and other phases. The nitrogen diffusion decreases the austenitization temperature and results in the formation of martensite after the sample cooling in the electrolyte. The formation of a carbon and nitrogen source in a vapor-gas envelope (VGE) is investigated. The proposed mechanism includes evaporation of acetonitrile in the VGE, its adsorption on an anode with the following thermal decomposition, and also the acetonitrile reduction to amine with subsequent hydrolysis to ethanol that is determined with the use of chromatographic method. The aqueous solution that contained 10 wt.% NH4Cl and 10 wt.% CH3CN allows one to obtain the nitrocarburized layer with the thickness of 0.22 mm and microhardness up to 740 HV during 10 min at 850 °C. This treatment regime leads to the decrease in the surface roughness of steel R a from 1.01 μm to 0.17 μm.

  18. Case-hardening medium carbon steel for tough and long life bearing under severe lubrication conditions

    SciTech Connect

    Furumura, Kyozaburo; Murakami, Yasuo; Abe, Tsutomu

    1998-12-31

    It is known these days that case-hardening bearings have a longer life than through-hardening ones under severe lubrication conditions (i.e., mixing-in of foreign particles in the lubrication oil). To explain this fact, the authors first presented the mechanism of stress relaxation at the debris dent edge. According to test results, it was found that both retained austenite and hardness are the most important factors for a longer life material. Such material has a longer life even under boundary lubrication conditions. Since a sufficient EHL oil film does not form under boundary lubrication conditions, metal contact occurs. The resulting damage is called peeling and it decreases the bearing life. To realize ideal case hardening material for bearings, a new carbo-nitride heat treatment has been developed. Normally, it is extremely difficult to obtain a sufficient case depth using a traditional carbo-nitride heat treatment process. As an alternate, medium carbon steel was studied. The application of newly developed medium carbon steel has not only proved to make the creation of a sufficient case depth easier, but also provided economic benefits. Based on results from testing both the dimensional stability and fracture toughness, newly developed medium carbon steel can be used for case-hardening bearings.

  19. A pharmaceutical product as corrosion inhibitor for carbon steel in acidic environments.

    PubMed

    Samide, Adriana

    2013-01-01

    A pharmaceutical product, Trimethoprim (TMP), IUPAC name: 5-(3,4,5-trimethoxybenzyl)pyrimidine-2,4-diamine was investigated, as inhibitor to prevent carbon steel corrosion in acidic environments. The study was performed using weight loss and electrochemical measurements, in temperatures ranging between 25-55°C. The surface morphology before and after corrosion of carbon steel in 1.0 M HCl solution in the presence and absence of TMP was evaluated using scanning electron microscopy (SEM). The inhibition efficiency (IE) increased with the increasing of the inhibitor concentration, reaching a maximum value of 92% at 25°C and 0.9 mM TMP, and decreased with increasing temperature. The inhibition of carbon steel corrosion by TMP can be attributed to the adsorption ability of inhibitor molecules onto the reactive sites of the metal surface. The adsorption is spontaneous and it is best described by the Langmuir isotherm. The apparent activation energy (E(a)) for the corrosion process in the absence and presence of TMP was evaluated from Arrhenius equation, to elucidate its inhibitive properties.

  20. Mathematical Modeling and Microstructure Analysis of Low Carbon Steel Strips Produced by Horizontal Single Belt Casting (HSBC)

    NASA Astrophysics Data System (ADS)

    Ge, Sa; Chang, Sheng; Wang, Tong; Calzado, Luis E.; Isac, Mihaiela; Kozinski, Janusz; Guthrie, Roderick I. L.

    2016-06-01

    The horizontal single belt casting (HSBC) process has been proposed as an efficient, economical, and environmentally friendly alternative approach to the production of ferrous alloys. Low carbon steel strips were cast using the HSBC simulator apparatus to study the characteristics and properties of the as-cast steel strips. Three-dimensional computational fluid dynamics simulations using ANSYS FLUENT 14.5 were also performed. Numerical predictions were validated against experimental casting results. Microstructural analyses and as-cast surface texture studies were conducted on low carbon steels.

  1. The effects of carbon and nitrogen on the corrosion resistance of type 316 stainless steel to liquid lithium

    NASA Astrophysics Data System (ADS)

    Barker, M. G.; Frankham, S. A.

    1982-06-01

    Type 316 stainless steel plates have been exposed at 600°C to liquid lithium containing carbon and nitrogen at various chemical activities for periods of up to 672 h. The corrosion products Li 9CrN 5 and M 23C 6 have been identified on the plate surfaces and in the grain boundaries. Scanning electron microscopy has shown preferential nickel and chromium depletion at the steel surface in lithium with high nitrogen content. The diffusion coefficient of carbon in type 316 stainless steel from a lithium source was found to be 6.5 × 10 t 1¯5 m 2/s.

  2. Adsorption and corrosion-inhibiting effect of Dacryodis edulis extract on low-carbon-steel corrosion in acidic media.

    PubMed

    Oguzie, E E; Enenebeaku, C K; Akalezi, C O; Okoro, S C; Ayuk, A A; Ejike, E N

    2010-09-01

    The inhibition of low-carbon-steel corrosion in 1M HCl and 0.5M H(2)SO(4) by extracts of Dacryodis edulis (DE) was investigated using gravimetric and electrochemical techniques. DE extract was found to inhibit the uniform and localized corrosion of carbon steel in the acidic media, affecting both the cathodic and anodic partial reactions. The corrosion process was inhibited by adsorption of the extracted organic matter onto the steel surface in a concentration-dependent manner and involved both protonated and molecular species. Molecular dynamics simulations were performed to illustrate the process of adsorption of some specific components of the extract.

  3. Numerical Simulations of Carbon and Nitrogen Composition-Depth Profiles in Nitrocarburized Austenitic Stainless Steels

    NASA Astrophysics Data System (ADS)

    Gu, Xiaoting; Michal, Gary M.; Ernst, Frank; Kahn, Harold; Heuer, Arthur H.

    2014-09-01

    Unusual composition-depth profiles have been observed after low-temperature nitrocarburization of austenitic stainless steels. When nitridation is performed after carburization, the carbon concentration in the nitrogen diffusion zone is reduced from ≈10 to ≈2 at. pct. Conversely, the carbon concentration in advance of the nitrogen diffusion zone is as high as 10 at. pct. This has been called a "push" effect of nitrogen on carbon, but this concept is non-physical. The profiles can be better understood from conventional thermodynamic principles, recognizing that (1) diffusion always occurs in response to gradients in chemical potentials and (2) the diffusivity of interstitial solutes in austenite is strongly concentration dependent, increasing dramatically with higher solute concentrations. Parameters from the CALPHAD literature quantitatively indicate that interstitial nitrogen and carbon in austenitic stainless steel mutually increase their chemical potentials. Based on these data, we have conducted numerical simulations of composition-depth profiles that correctly account for the chemical potential gradients and the concentration dependence of the diffusion coefficients for nitrogen and carbon. The simulations predict the "push" effect observed on nitridation after carburization, as well as the corresponding composition-depth profiles for other scenarios, e.g., carburization followed by nitridation or simultaneous nitridation and carburization (nitrocarburization).

  4. THE REMOVAL OF CARBON/BEUTERIUM FROM STAINLESS STEEL AND TUNGSTEN BY TRANSFERRED-ARC CLEANING

    SciTech Connect

    K. J. HOLLIS; R. G. CASTRO; ET AL

    2001-04-01

    Tungsten and stainless steel samples have been contaminated with deuterium and carbon to simulate deposited layers in magnetic-confinement fusion devices. Deuterium and carbon were co-deposited onto the sample surfaces using a deuterium plasma seeded with varying amounts of deuterated methane. Deuterium was also implanted into the samples in an accelerator to simulate hydrogen isotope ion implantation conditions in magnetic confinement fusion devices. Cathodic arc, or transferred-arc (TA) cleaning was employed to remove the deposits from the samples. The samples were characterized by ion beam analysis both before and after cleaning to determine deuterium and carbon concentrations present. The deuterium content was greatly reduced by the cleaning thus demonstrating the possibility of using the TA cleaning technique for removing deuterium and/or tritium from components exposed to D-T fuels. Removal of surface layers and significant reduction of subsurface carbon concentrations was also observed.

  5. Outbursts formation on low carbon and trip steel grades during hot-dip galvanisation

    NASA Astrophysics Data System (ADS)

    Petit, E. J.; Lamm, L.; Gilles, M.

    2004-12-01

    Low carbon and TRIP grade steels have been hot dip galvanised in order to study outbursts formation. Microstructure and texture of intermetallic phases have been observed after selective electrochemical etching by scanning electron microscopy. Potential versus time (chronopotentiometric) characteristics were recorded in order to monitor surface modifications. This combination of techniques enable to quantify and observe intermetallic phase one by one. The overall thickness of coating on both substrates are similar. However, microstructures of Fe-Zn intermetallic phases are very different on both grades. In particular, the V phase is dense on standard steel but develops a highly branched filament structure on TRIP steel. The transformation of V phase to d and G1 are limited on TRIP steel. Differences of texture provide clues for understanding mechanisms of formation of outbursts. They can account for the differences of mechanical properties and corrosion resistance. Silicon from the substrate influences the reactivity of TRIP steels due to capping and local reactions. La formation des outbursts a été étudiée sur un acier bas carbone et sur un acier TRIP galvanisés. Les épaisseurs des revêtements sont similaires. Néanmoins, les observations microscopiques et les érosions électrochimiques montrent que la répartition des phases intermétalliques et leurs microstructures diffèrent sensiblement en fonction de la nature du substrat. Ces différences expliquent les propriétés mécaniques et anticorrosions. L’encapsulation de la surface par les oxydes de silicium freine la transformation de la phase dzêta en delta et gamma sur l’acier TRIP.

  6. Stability of retained austenite in high carbon steel under compressive stress: an investigation from macro to nano scale.

    PubMed

    Hossain, R; Pahlevani, F; Quadir, M Z; Sahajwalla, V

    2016-10-11

    Although high carbon martensitic steels are well known for their industrial utility in high abrasion and extreme operating environments, due to their hardness and strength, the compressive stability of their retained austenite, and the implications for the steels' performance and potential uses, is not well understood. This article describes the first investigation at both the macro and nano scale of the compressive stability of retained austenite in high carbon martensitic steel. Using a combination of standard compression testing, X-ray diffraction, optical microstructure, electron backscattering diffraction imaging, electron probe micro-analysis, nano-indentation and micro-indentation measurements, we determined the mechanical stability of retained austenite and martensite in high carbon steel under compressive stress and identified the phase transformation mechanism, from the macro to the nano level. We found at the early stage of plastic deformation hexagonal close-packed (HCP) martensite formation dominates, while higher compression loads trigger body-centred tetragonal (BCT) martensite formation. The combination of this phase transformation and strain hardening led to an increase in the hardness of high carbon steel of around 30%. This comprehensive characterisation of stress induced phase transformation could enable the precise control of the microstructures of high carbon martensitic steels, and hence their properties.

  7. Characteristics of medium carbon steel solidification and mold flux crystallization using the multi-mold simulator

    NASA Astrophysics Data System (ADS)

    Park, Jun-Yong; Ko, Eun-yi; Choi, Joo; Sohn, Il

    2014-11-01

    An oscillating multi-mold simulator with embedded thermocouples was used to study the initial solidification of medium carbon steels and crystallization characteristics of the mold flux. Casting speed variations in the simulator from 0.7 m/min to 1.4 m/min at fixed oscillation frequency and stroke resulted in higher copper mold temperatures. Frequency modifications from 2.5 Hz to 5.0 Hz and stroke changes from 8.1 mm to 5.4 mm at fixed casting speeds also resulted in higher copper mold temperatures. Surface profile analysis of as-cast steel strips showed characteristic oscillation marks comparable to the narrow faces of the industrial cast slabs. The apparent effect of casting variables on the temperature and surface profiles during the solidification of the medium carbon steels could be correlated to the variations in the negative strip time and subsequent changes in the extent of mold flux infiltration. Back scattered scanning electron microscope analysis of the full length of the retrieved flux film after casting showed cuspidine crystallization ratio that increased from the upper to lower portion of the flux film. This dynamic crystallization and growth of the cuspidine phase increases as the flux is sustained at high temperatures for longer periods. Additional experiments with industrial fluxes designed for soft cooling of medium carbon steel grades showed comparable infiltration thickness of the flux, but the crystallization characteristics were significantly different, which could have a significant impact on the heat transfer rate and mechanism through the flux film.

  8. Analyses of quenching process during turn-off of plasma electrolytic carburizing on carbon steel

    NASA Astrophysics Data System (ADS)

    Wu, Jie; Liu, Run; Xue, Wenbin; Wang, Bin; Jin, Xiaoyue; Du, Jiancheng

    2014-10-01

    Plasma electrolytic carburizing (PEC) under different turn-off modes was employed to fabricate a hardening layer on carbon steel in glycerol solution without stirring at 380 V for 3 min. The quenching process in fast turn-off mode or slow turn-off mode of power supply was discussed. The temperature in the interior of steel and electron temperature in plasma discharge envelope during the quenching process were evaluated. It was found that the cooling rates of PEC samples in both turn-off modes were below 20 °C/s, because the vapor film boiling around the steel sample reduced the cooling rate greatly in terms of Leidenfrost effect. Thus the quench hardening hardly took place, though the slow turn-off mode slightly decreased the surface roughness of PEC steel. At the end of PEC treatment, the fast turn-off mode used widely at present cannot enhance the surface hardness by quench hardening, and the slow turn-off mode was recommended in order to protect the electronic devices against a large current surge.

  9. The Corrosion Behavior of Carbon Steel in Sulfide Aqueous Media at 30°C

    NASA Astrophysics Data System (ADS)

    El Mendili, Yassine; Abdelouas, Abdesselam; Bardeau, Jean-François

    2014-04-01

    In this paper, we studied the effect of sulfide ions on the corrosion behavior of carbon steel to simulate the geological disposal of high-level radioactive waste. In geological storage conditions, sulfidogenic environment was sustained by sulfate-reducing bacteria. Corrosion tests were conducted in systems in a controlled atmosphere of 5% H2/N2. Batch experiments were conducted at 30°C for 1 month with steel coupons immersed in Na2S solutions. The structural characterization of the corrosion products was investigated by scanning electron microscope/energy dispersive x-ray spectroscopy, confocal micro-Raman spectrometry, and x-ray diffraction. In the absence of sulfide ion, a magnetite (Fe3O4) corrosion product layer was formed on steel surface while in the presence of sulfide ions we observed the formation of a poorly crystallized irons sulfide at low-sulfide concentration (1 mg/L) and a solid adherent pyrrhotite layer at higher sulfide concentration (5-15 mg/L). The strong drop in steel corrosion rate with sulfide concentration was revealed and related to the formation of well-crystallized pyrrhotite.

  10. Application of carbon FRP for fatigue strengthening of old steel structures

    NASA Astrophysics Data System (ADS)

    Vůjtěch, J.; Ryjáček, P.; Vovesný, M.

    2017-02-01

    The traffic requirements on the existing infrastructure are rising still. This coupled with its age puts a strain on it. This is especially problematic for old steel bridges. Higher and more frequent loads will lead to development of fatigue damage to those structures. This causes an issue for the infrastructure owners as the existing methods of repair are difficult, time consuming and expensive. So there is a need to find some easier alternatives. One of such can be the use of carbon fibre reinforced polymers (CFRP). They are being successfully used for repairs and strengthening of concrete structures however their use with steel is still relatively new. The purpose of this work is to establish how does a deteriorated steel reinforced with CFRP behave under fatigue loading. To test this a series of experiments was designed. With the help of a preliminary numerical study the dimensions of the specimens and the applied loading was established. There are two sets of specimens. With both we are using mild steel and each set has different level of surface deterioration (corrosion pits or corrosion holes). The specimens are reinforced using hand laid wet layup composites. They are subjected to fatigue loading and the difference between the fatigue life reinforced and unreinforced specimens is observed. Based on the preliminary study, it is expected, that the reinforcement will prolong the life expectancy by half.

  11. Microstructural and Mechanical Evolution of a Low Carbon Steel by Friction Stir Processing

    NASA Astrophysics Data System (ADS)

    Sekban, Dursun Murat; Aktarer, Semih Mahmut; Zhang, Hao; Xue, Peng; Ma, Zongyi; Purcek, Gencaga

    2017-08-01

    A low carbon steel (Grade A) was subjected to friction stir processing (FSP), and the effect of FSP on the microstructure and mechanical properties was investigated systematically. It was found that two distinct zones called stir zone (SZ) and heat-effected zone (HAZ) were formed during FSP. The SZ and HAZ consist mainly of ferrite, widmanstatten ferrite, ferrite+cementite aggregates, and martensite. FSP considerably refined the microstructure of the steel by means of dynamic recrystallization mechanism and formed a volumetric defect-free basin-like processed region. The ferritic grain size of the steel decreased from 25 µm in the coarse-grained state to about 3 µm in the fine-grained state, and the grains formed were separated mostly by high angle of misorientation with low density of dislocations. This microstructural evolution brought about a considerable increase in both hardness and strength values without a considerable decrease in ductility. Ultrafine-grained microstructure formed around and just beneath the pin increased the hardness of the steel from 140 Hv0.3 to about 245 Hv0.3. However, no hardness uniformity was formed throughout the processed zone due to the changes in deformation- and temperature-induced microstructure. Both yield and tensile strength values of processed zone increased from 256 and 435 MPa to about 334 and 525 MPa, respectively.

  12. Pyrolytic carbon-coated stainless steel felt as a high-performance anode for bioelectrochemical systems.

    PubMed

    Guo, Kun; Hidalgo, Diana; Tommasi, Tonia; Rabaey, Korneel

    2016-07-01

    Scale up of bioelectrochemical systems (BESs) requires highly conductive, biocompatible and stable electrodes. Here we present pyrolytic carbon-coated stainless steel felt (C-SS felt) as a high-performance and scalable anode. The electrode is created by generating a carbon layer on stainless steel felt (SS felt) via a multi-step deposition process involving α-d-glucose impregnation, caramelization, and pyrolysis. Physicochemical characterizations of the surface elucidate that a thin (20±5μm) and homogenous layer of polycrystalline graphitic carbon was obtained on SS felt surface after modification. The carbon coating significantly increases the biocompatibility, enabling robust electroactive biofilm formation. The C-SS felt electrodes reach current densities (jmax) of 3.65±0.14mA/cm(2) within 7days of operation, which is 11 times higher than plain SS felt electrodes (0.30±0.04mA/cm(2)). The excellent biocompatibility, high specific surface area, high conductivity, good mechanical strength, and low cost make C-SS felt a promising electrode for BESs.

  13. Modeling of the peritectic reaction and macro-segregation in casting of low carbon steel

    NASA Astrophysics Data System (ADS)

    El-Bealy, M.; Fredriksson, H.

    1996-12-01

    Macro-microscopic models have been developed to describe the macrosegregation behavior associated with the peritectic reaction of low carbon steel. The macrosegregation model has been established on the basis of previously published work and experimental data. A microscopic model of a three-phase reaction L+ δ→ γ has been modeled by using Fredriksson’s approach. Four horizontal and unidirectional solidified experimental groups simulating continuous casting have been performed with a low carbon steel containing 0.13 wt pct carbon. The extent of macrosegregation of carbon was determined by wet chemical analysis of millings. It is confirmed, by comparing calculated results with experimental results, that this model successfully predicts the occurrence of macrosegregation. The results indicate that a peritectic reaction which is associated with a high cooling rate generates high thermal contraction and a high tensile strain rate at the peritectic temperature. Therefore, the macrosegregation, particularly at the ingot surface, is very sensitive to the cooling rate, where extremely high positive segregation was observed in the case of a high cooling rate. However, in the case of slow cooling rate, negative segregation was noted. The mechanism of macrosegregation with peritectic reaction is discussed in detail.

  14. Impact of Desulfovibrio alaskensis biofilms on corrosion behaviour of carbon steel in marine environment.

    PubMed

    Wikieł, Agata J; Datsenko, Iaryna; Vera, Mario; Sand, Wolfgang

    2014-06-01

    Sulfate reducing prokaryotes are associated with the steel deterioration. They build heterogeneous biofilms, capable of accelerating corrosion processes. In this study metabolic activity and the biofilm development of Desulfovibrio alaskensis were correlated to electrochemical response of carbon steel surface. In the exponential growth phase sulfide concentration reached its maximum of about 10mM. This phenomenon was responsible for the parallel increase in the corrosion potential (Ecorr) up to -720mV (vs. SCE). Subsequently, during the intensive biofilm formation and development another Ecorr peak (-710mV vs. SCE) occurred. Decrease in Ecorr was registered during the biofilm maturation and kept stable, being 20mV lower than in the control. While carbon steel was protected from the microbial attachment and exposed to metabolic products, only one potential maximum (-730mV vs. SCE) was recorded. Here Ecorr variations coincided with sulfide concentration changes and kept at 120mV lower vs. the control. Weight loss examinations revealed corrosion rates, which did not exceed 0.05mm/y. Confocal microscopy suggested the importance of extracellular proteins in the biofilm formation. Above 150 proteins were detected in the EPS matrix. Surface effects of biofilm and metabolic products were visualised, revealing the role of attached microorganisms in the localised corrosion.

  15. Rapid annealing of severely deformed low carbon steel in subcritical temperature range

    NASA Astrophysics Data System (ADS)

    Ghiabakloo, H.; Kazeminezhad, M.

    2017-09-01

    A low-carbon steel sheet containing 0.05 C, 0.203 Mn, and 0.0229 Si (all in wt%) was rapidly annealed in a temperature range of 300 °C to 600 °C after severe plastic deformation by using constrained groove pressing (CGP) technique. Microstructure evolution was investigated by scanning electron and optical microscopes. Mechanical properties were evaluated by hardness measurements and shear punch test. The results showed a thermal stability up to 400 °C where recrystallization did not occur in the specimens even after 7200 s. This thermal stability is in agreement with previously reported results of conventional annealing of the same steel after CGP. However, annealing at 500 °C and 600 °C led to recrystallization which started after holding times of 600 s and 20 s, respectively. Longer holding times resulted to grain growth and deterioration of strength and hardness, but the final strength and hardness were still higher than those of conventionally annealed specimens. The reason has been attributed to no abnormal grain growth in the present study, in contrast to that occurs after conventional annealing of CGPed low carbon steel. The kinetics of recrystallization at 600 °C was studied using the celebrated Johnson-Mehl-Avrami-Kolmogorov (JMAK) model; the results showed a bi-linear JMAK plot indicating two different stages of recrystallization rate before and after 70% recrystallization.

  16. Pitting growth rate in carbon steel exposed to simulated radioactive waste

    SciTech Connect

    Zapp, P.E.

    1996-11-01

    Dilute high-level radioactive waste slurries can induce pitting corrosion in carbon steel tanks in which such waste is stored and processed. The waste is normally maintained with closely monitored nitrite and hydroxide concentrations known to prevent the initiation of pitting. Coupon immersion tests are being conducted in laboratory simulants of waste to determine the probability and growth rate of pitting in steel in the event of out-of-limits nitrite concentrations. Sets of about 36 carbon steel coupons have been immersed in known corrosive conditions (nitrite < 5 per cent of the established limit) at a temperature of 50 degrees C. Three sets have been removed from testing after 64, 150, and 350 days of immersion. The long immersion times introduced variability in the exposure conditions due to the evaporation and replenishment of solution. The deepest corrosive attack was measured on each coupon by optical microscopy. The deepest pits were ranked and analyzed as a type 1 extreme value distribution to extrapolate from the coupon population to the maximum expected pit depths in a waste tank structure. The data were compared to a power law for pit growth, although the deepest pits did not increase monotonically with time in the limited data set

  17. Pitting growth rate in carbon steel exposed to simulated radioactive waste

    SciTech Connect

    Zapp, P.E.

    1995-12-31

    Dilute high-level radioactive waste slurries can induce pitting corrosion in carbon steel tanks in which such waste is stored and processed. The waste is normally maintained with closely monitored nitrite and hydroxide concentrations known to prevent the initiation of pitting. Coupon immersion are being conducted in laboratory simulants of waste to determine the probability and growth rate of pitting in steel in the event of below-limits nitrite concentrations. Sets of about 36 carbon steel coupons have been immersed in known corrosive conditions (nitrite < 5% of the established limit) at a temperature of 50 C. Three sets have been removed from testing after 64, 150, and 350 days of immersion. The long immersion times introduced variability in the exposure conditions due to the evaporation and replenishment of solution. The deepest corrosive attack was measured one each coupon by optical microscopy. The deepest pits were ranked and analyzed as a type 1 extreme value distribution to extrapolate from the coupon population to the maximum pit depths in a waste tank structure. The data were compared to a power law for pit growth, although the deepest pits did not increase monotonically with time in the limited data set.

  18. Carbon and nitrogen effects on sensitization resistance of type 347 stainless steels

    SciTech Connect

    Oh, Y.J.; Yoon, J.H.; Hong, J.H.

    2000-03-01

    The sensitization resistance of the stabilized Type 347 (UNS S34700) stainless steels (SS) having different carbon and nitrogen contents was evaluated using the double-loop electrochemical potentiokinetic reactivation (DL-EPR) and ASTM A262, practice E methods. Samples were heat-treated to simulate the coarse grain region of the heat-affected zone (HAZ) during welding and subsequently aged at 948 K for different times. For comparison, DL-EPR tests also were conducted for the unstabilized steels, Type 316 (UNS S31600) and Type 304 (UNS S30400). For Type 347 SS, a criterion for sensitization in accordance with the ASTM A262, practice E test corresponded to a condition of > 10% reactivation ratio (peak reactivation current [I{sub r}]/peak activation current [I{sub a}]) from DL-EPR test. The carbon and nitrogen effects on the sensitization resistance of the Type 347 SS were explained in view of the observed microstructures. BY introducing a resistance parameter based on the chemical composition, sensitization resistance of the stabilized Type 347 SS and the unstabilized steels was expressed as a unified function.

  19. The effect of heat treatment on the hardness and impact properties of medium carbon steel

    NASA Astrophysics Data System (ADS)

    Mazni Ismail, Noor; Khatif, Nurul Aida Amir; Aliff Kamil Awang Kecik, Mohamad; Hanafiah Shaharudin, Mohd Ali

    2016-02-01

    This paper covers the effect of heat treatment on the mechanical properties of medium carbon steel. The main objective of this project is to investigate the hardness and impact properties of medium carbon steel treated at different heat treatment processes. Three types of heat treatment were performed in this project which are annealing, quenching and tempering. During annealing process, the specimens were heated at 900°C and soaked for 1 hour in the furnace. The specimens were then quenched in a medium of water and open air, respectively. The treatment was followed by tempering processes which were done at 300°C, 450°C, and 600°C with a soaking time of 2 hours for each temperature. After the heat treatment process completed, Rockwell hardness test and Charpy impact test were performed. The results collected from the Rockwell hardness test and Charpy impact test on the samples after quenching and tempering were compared and analysed. The fractured surfaces of the samples were also been examined by using Scanning Electron Microscope. It was observed that different heat treatment processes gave different hardness value and impact property to the steel. The specimen with the highest hardness was found in samples quenched in water. Besides, the microstructure obtained after tempering provided a good combination of mechanical properties due to the process reduce brittleness by increasing ductility and toughness.

  20. The influence of Cr and Al pack cementation on low carbon steel to improve oxidation resistance

    NASA Astrophysics Data System (ADS)

    Prasetya, Didik; Sugiarti, Eni; Destyorini, Fredina; Thosin, Kemas Ahmad Zaini

    2012-06-01

    Pack chromizing and aluminizing has been widely used for many years to improve hot temperature oxidation and corrosion resistance of metals. The coating process involves packing the steel in a powder mixture which contain aluminum and chromium source, and inert filler (usually alumina), and halide activator NH4Cl. Al and Cr were deposited onto carbon steel by pack cementation process using elemental Al and Cr powder as Al and Cr source, whereas NiCo alloys codeposited by electrodeposition. The position of Al and Cr could be under or over Ni-Co alloys deposited. Pack cementation was heated on dry inert gas at temperature 800 °C about 5 hours and 20 minute for Cr and Al respectively. Al and Cr was successfully deposited. Laying down effect of Al and Cr onto carbon steel whether up and down toward NiCo alloys coating have affected to oxidation resistance. The pack aluminizing as top layer given best resitance to restrain excessive oxide scale, in contrast pack chromizing reveal bad oxidation resistance, moreover occured spallation on layer.

  1. Electrochemical Corrosion Behavior of Low Carbon I-Beam Steels In Simulated Yucca Mountain Repository Environment

    SciTech Connect

    Arjunan, Venugopal; Lamb, Joshua; Chandra, Dhanesh; Daemen, Jack; Jones, Denny A.; Engelhard, Mark H.; Lea, Alan S.

    2005-04-01

    The electrochemical corrosion behavior of low carbon steel was examined in a simulated Yucca Mountain (YM) ground water by varying the electrolyte concentration and temperature under aerated and deaerated conditions. The results show that in deaerated conditions, the corrosion rate is low in the order of 0.6 to 4.5mpy, between 25 to 85 C, respectively. However, in aerated conditions the measured rates were expectedly very high, in the order of 3-55mpy in the above mentioned temperature levels. The rates initially increased up to 45 C, and a decreasing trend was observed with further increase in temperature from 65 to 85 C. The maximum corrosion rate was occurred at 45 C (54.5mpy). The low corrosion rates observed in all deaerated conditions, and in aerated solutions at higher temperatures were due to the preferential adsorption of Mg-species on the steel surface, as identified by XPS analyses. The results also indicate possible localized corrosion behavior of carbon steel in aerated conditions up to 45 C.

  2. Welding of HSLA-100 steel using ultra low carbon bainitic weld metal to eliminate preheating

    SciTech Connect

    Devletian, J.H.; Singh, D.; Wood, W.E.

    1996-12-31

    Advanced high strength steels such as the Navy`s HSLA-100 and HSLA-80 contain sufficiently low carbon levels to be weldable without preheating. Unfortunately, commercial filler metals specifically designed to weld these steels without costly preheating have not yet been developed. The objective of this paper is to show that the Navy`s advanced steels can be welded by gas metal-arc (GMAW) and gas tungsten-arc welding (GTAW) without preheating by using filler metal compositions that produce weld metal with an ultra-low carbon bainitic (ULCB) microstructure. Filler metals were fabricated from vacuum induction melted (VIM) ingots containing ultra-low levels of C, O and N. HSLA-100 plate and plate from the VIM ingots were welded by both GMAW and GTAW with Ar-5% CO{sub 2} shielding gas using welding conditions to achieve cooling times from 800 to 500 C (t{sub 8-5}) from 35 to 14 sec. Weld metal tensile, hardness and CVN impact toughness testing as well as microstructural studies using transmission electron microscopy were conducted. The ULCB weld metal was relatively insensitive to cooling rate, resulting in good strength and toughness values over a wide range of t{sub 8-5} cooling times. Filler metal compositions which met the mechanical property requirements for HSLA-100, HSLA-80 and HSLA-65 weld metal were developed.

  3. Crack initiation and crack growth behavior of carbon and low-alloy steels

    SciTech Connect

    Gavenda, D.J.; Luebbers, P.R.; Chopra, O.K.

    1997-01-01

    Section III of the ASME Boiler and Pressure Vessel Code specifies fatigue design curves for structural materials. These curves were based on tests of smooth polished specimens at room temperature in air. The effects of reactor coolant environments are not explicitly addressed by the Code design curves, but recent test data illustrate potentially significant effects of LWR coolant environments on the fatigue resistance of carbon and low-alloy steels. Under certain loading and environmental conditions, fatigue lives of test specimens may be a factor of {approx}70 shorter than in air. Results of fatigue tests that examine the influence of reactor environment on crack imitation and crack growth of carbon and low-alloy steels are presented. Crack lengths as a function of fatigue cycles were determined in air by a surface replication technique, and in water by block loading that leaves marks on the fracture surface. Decreases in fatigue life of low-alloy steels in high-dissolved-oxygen (DO) water are primarily caused by the effects of environment during early stages of fatigue damage, i.e., growth of short cracks <100 {micro}m in depth. For crack sizes of >100 {micro}m, crack growth rates in high-DO water are higher than in air by one order of magnitude. The effects of LWR environments on growth of short cracks are discussed.

  4. Hydrogen Generation During the Corrosion of Carbon Steel in Oxalic Acid

    SciTech Connect

    WIERSMA, BRUCEJ.

    2004-08-01

    A literature review of the corrosion mechanism for carbon steel in oxalic acid was performed to determine the ratio of moles of iron corroded to moles of hydrogen evolved during the corrosion of iron in oxalic acid. The theory of corrosion of carbon steel in oxalic acid and experimental work were reviewed. It was concluded that the maximum ratio of moles of hydrogen evolved to moles of iron corroded is 1:1. This ratio would be observed in a de-aerated environment. If oxygen or other oxidizing species are present, the ratio could be much less than 1:1. Testing would be necessary to determine how much less than 1:1 the ratio might be. Although the ratio of hydrogen evolution to iron corroded will not exceed 1:1, the total amount of hydrogen evolved can be influenced by such things as a decrease in the exposed surface area, suppression of hydrogen generation by gamma radiation, the presence of corrosion products on steel surface, etc. These and other variables present during chemical cleaning operations of the waste tank have not been examined by the tests reported in the literature i.e., the tests have focused on clean corrosion coupons in oxalic acid solutions. It is expected that most of these variables would reduce the total amount of hydrogen evolved. Further testing would need to be performed to quantify the reduction in hydrogen generation rate associated with these variables.

  5. Influence of the carbon content on the phase composition and mechanical properties of P92-type steel

    NASA Astrophysics Data System (ADS)

    Dudko, V. A.; Fedoseeva, A. E.; Belyakov, A. N.; Kaibyshev, R. O.

    2015-11-01

    The deformation behavior and the microstructure evolution under the creep of 10Kh9V2MFBR steel (Russian analog of the P92 steel) (in wt %, Fe-8.9% Cr-0.05% Si-0.2% Mn-1.9% W-0.5% Mo-0.25% V-0.07Nb-0.08% N-0.01% B) with the standard (0.1%) and lowered (0.018%) carbon contents have been investigated. After the heat treatment, which included normalizing at 1050°C and tempering at 720-750°C, carbides M 23 C 6 and carbonitrides M(C,N) are formed in the 10Kh9V2MFBR steel, while in the 02Kh9V2MFBR steel (modified P92 steel), carbides M 23 C 6, nitrides M 2N, and carbonitrides M(C,N) as well as δ-ferrite (23%) were found. The measurements of hardness and tensile tests at room and elevated temper-atures did not reveal substantial distinctions in the short-term mechanical properties of both steels. The hardness of steels after tempering was 220 HB. At the same time, the creep characteristics of the steels were found to be different. A decrease in the carbon content leads to an increase in the long-term creep strength and creep limit at 650°C for short-term tests with time-to-fracture shorter than 103 h. The time to fracture of steels with various carbon contents is almost the same in long-term creep tests. Factor responsible for such effect of carbon on the creep strength are discussed.

  6. Influence of TiN Inclusions on the Cleavage Fracture Behavior of Low-Carbon Microalloyed Steels

    NASA Astrophysics Data System (ADS)

    Yan, W.; Shan, Y. Y.; Yang, K.

    2007-06-01

    Toughness is a major concern for low-carbon microalloyed steels. In this work, the impact fracture behavior of two low-carbon Ti-V microalloyed steels was investigated in order to better understand the role of TiN inclusions in the toughness of the steels. The steels had similar chemical compositions and were manufactured by the same rolling process. However, there was an obvious difference in the ductile brittle transition temperature (DBTT) in the Charpy V-notch (CVN) impact tests of the two steels; one (steel 1) possessing a DBTT below -20 °C, while the DBTT of the other (steel 2) was above 15 °C. Scanning electron microscopy (SEM) fractography revealed that there were TiN inclusions at the cleavage fracture initiation sites on the fracture surfaces of steel 2 at both low and room temperatures. It is shown that the TiN inclusions had nucleated on Al2O3 particles and that they had pre-existing interior flaws. A high density of TiN inclusions was found in steel 2, but there was a much lower density in steel 1. Analysis indicates that these inclusions were responsible for the shift of DBTT to a higher temperature in steel 2. A mechanism is proposed for understanding the effect of the size and density of TiN inclusions on the fracture behavior, and the cleavage fracture initiation process is analyzed in terms of the distribution and development of stresses ahead of the notch tip during fracture at both low and room temperatures.

  7. Pyrolysis-catalysis of waste plastic using a nickel-stainless-steel mesh catalyst for high-value carbon products.

    PubMed

    Zhang, Yeshui; Nahil, Mohamad A; Wu, Chunfei; Williams, Paul T

    2017-02-03

    A stainless-steel mesh loaded with nickel catalyst was produced and used for the pyrolysis-catalysis of waste high-density polyethylene with the aim of producing high-value carbon products, including carbon nanotubes (CNTs). The catalysis temperature and plastic-to-catalyst ratio were investigated to determine the influence on the formation of different types of carbon deposited on the nickel-stainless-steel mesh catalyst. Increasing temperature from 700 to 900°C resulted in an increase in the carbon deposited on the nickel-loaded stainless-steel mesh catalyst from 32.5 to 38.0 wt%. The increase in sample-to-catalyst ratio reduced the amount of carbon deposited on the mesh catalyst in terms of g carbon g(-1) plastic. The carbons were found to be largely composed of filamentous carbons, with negligible disordered (amorphous) carbons. Transmission electron microscopy analysis of the filamentous carbons revealed them to be composed of a large proportion (estimated at ∼40%) multi-walled carbon nanotubes (MWCNTs). The optimum process conditions for CNT production, in terms of yield and graphitic nature, determined by Raman spectroscopy, was catalysis temperature of 800°C and plastic-to-catalyst ratio of 1:2, where a mass of 334 mg of filamentous/MWCNTs g(-1) plastic was produced.

  8. Effect of carbon, manganese, nickel, and nitrogen concentrations on the phase composition and properties of wrought high-manganese steel

    NASA Astrophysics Data System (ADS)

    Samarin, N. Ya.; Kats, R. Z.; Startsev, V. A.; Petrova, I. A.

    1981-01-01

    Strain hardening of high-manganese steel is characterized not only by the formation of dislocations but also by precipitation of second phase (primarily α martensite with a carbon concentration <1.0% and carbides with a carbon content >1.2%), lowering the ductility of the cold worked metal, which induces the formation on the working surfaces of defects due to contact fatigue.

  9. 75 FR 64250 - Certain Welded Carbon Steel Pipe and Tube From Turkey: Notice of Final Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-19

    ... this order, except for line pipe, oil country tubular goods, boiler tubing, cold- drawn or cold-rolled... International Trade Administration Certain Welded Carbon Steel Pipe and Tube From Turkey: Notice of Final... the preliminary results of the antidumping duty administrative review of certain welded carbon...

  10. Influence of Carbon Content and Rolling Temperature on Rolling Texture in 3 Pct Si Steel

    NASA Astrophysics Data System (ADS)

    Shingaki, Y.; Takashima, M.; Hayakawa, Y.

    2017-01-01

    Effects of carbon and rolling temperature up to 453 K (180 °C) on rolling texture of 3 pct Si steel at a reduction of 66 pct were investigated using a single crystal with an initial orientation of {110}<001>. With residual-level carbon, uniform slip deformation was observed in the specimen cold rolled at room temperature and most of initial orientation {110}<001> rotated to {111}<112> during the rolling. With carbon addition, the formation of the deformation twins and the shear bands were promoted in the specimen cold rolled at room temperature. Regions with {110}<001> were observed inside the shear bands. Warm-rolled specimen with residual-level carbon had microbands containing tiny {110}<001> regions. Warm-rolled specimen with carbon addition had both the shear bands and the microbands but no deformation twin. Additionally, there were unique band structures with rotated crystal orientation around the rolling direction from initial orientation {110}<001>. These experimental results suggest that the carbon addition inhibits dislocation migration by the increase of the critical resolved shear stress (CRSS) and that the high deformation temperature activates multiple slip systems by the reduction of CRSS and further that the carbon addition and high deformation temperature superimposed bring about the activation of symmetrical {110} slip systems additionally.

  11. High temperature, high strain rate extrusion of ultrahigh-carbon steels

    SciTech Connect

    Lesuer, D R; Syn, C K; Sherby, O D

    2000-08-23

    It is shown that high rate extrusion is a viable production process for obtaining desirable microstructures and mechanical properties in ultrahigh carbon steels (UHCSs). The coefficient of friction for extrusion was determined for the UHCSs as well as five other materials and shown to be a function of stress--decreasing with increasing stress. The extruded UHCSs deform by a diffusion-controlled dislocation creep process. Stacking fault energies have been calculated from the extrusion data and observed to decrease with increasing concentrations of silicon, aluminum and chromium. Microstructures are either ultrafine pearlite when extruded above the eutectoid temperature or ultrafine spheroidite when extruded below the eutectoid temperature. The resulting strength--ductility properties are shown to be superior to those obtained in high-strength low alloy steels.

  12. Influence of EPS isolated from thermophilic sulphate-reducing bacteria on carbon steel corrosion.

    PubMed

    Dong, Ze Hua; Liu, Tao; Liu, Hong Fang

    2011-05-01

    Extracellular polymeric substances (EPS) were isolated by centrifugation of thermophilic sulphate-reducing bacteria (SRB) grown in API-RP38 culture medium. The protein and polysaccharide fractions were quantified and the highest concentrations were extracted from a 14-day old culture. The effect of EPS on carbon steel corrosion was investigated by electrochemical techniques. At 30°C, a small amount of EPS in 3% NaCl solution inhibited corrosion, whilst excessive amounts of EPS facilitated corrosion. In addition, the inhibition efficiency of EPS decreased with temperature due to thermal desorption of the EPS. The results suggest that adsorbed EPS layers could be beneficial to anti-corrosion by hindering the reduction of oxygen. However, the accumulation of an EPS film could stimulate the anodic dissolution of the underlying steel by chelation of Fe2+ ions.

  13. Method for the preparation of high-strength fine wire of high-carbon steel

    SciTech Connect

    Nishiura, Shuji; Izumisano-shi; Osaka-fu; Nishiura, Yoshitaka.

    1993-06-22

    In a method for the manufacture of a fine high-carbon steel wire having a diameter not exceeding 50[mu]m by repeating a plural number of cycles each consisting of a cold die-drawing treatment and a patenting treatment of a steel wire ending in a final cold die-drawing to successively reduce the diameter of the wire in each cold die-drawing, the improvement is described which comprises heating the wire having a diameter reduced to 100 to 500 [mu]m, prior to the final cold die-drawing treatment, in an atmosphere of a gaseous mixture consisting of from 90 to 98% by volume of nitrogen and from 10 to 2% by volume of hydrogen at a temperature in the range from 750 to 900 C for a length of time in the range from 1 to 30 seconds.

  14. Enhanced Adhesion of Diamond-Like Carbon Coatings on 316 Stainless Steel

    NASA Astrophysics Data System (ADS)

    Chen, M.; Gao, J.

    Diamond-like carbon (DLC) has been a candidate prosthetic coating due to its excellent physical and chemical properties, and biocompatibility. However, the adhesion to a number of prosthetic materials is still an issue. Different techniques have been used to improve the adhesion of DLC on various substrates. In this paper, we report the fabrication of an adherent DLC coating on commercial 316 stainless steel by using pulsed laser deposition and a composition-graded intermediate layer. Intermediate layers with graded composition from stainless steel to DLC were obtained by designing an inlaid target. Raman spectrum analysis indicated that the grown DLC films are rich in sp3 bonds. The adhesion of the coatings as well as other properties of the intermediate layers are also discussed.

  15. Effect of Quenching Process on the Microstructure and Hardness of High-Carbon Martensitic Stainless Steel

    NASA Astrophysics Data System (ADS)

    Zhu, Qin-tian; Li, Jing; Shi, Cheng-bin; Yu, Wen-tao

    2015-11-01

    The microstructure and hardness of high-carbon martensitic stainless steel (HMSS) were investigated using thermal expansion analyzer, Thermo-calc, scanning electron microscope, x-ray diffraction, and Ultra-high temperature confocal microscope. The results indicate that the experimental steel should be austenitized in the temperature range of 1025-1075 °C, which can give a maximum hardness of 62 HRc with the microstructure consisting of martensite, retained austenite, and some undissolved carbides. With increasing austenitizing temperature, the amount of retained austenite increases, while the volume fraction of carbides increases first and then decreases. The starting temperature and finish temperature of martensite formation decrease with increasing cooling rates. Air-quenched samples can obtain less retained austenite, more compact microstructure, and higher hardness, compared with that of oil-quenched samples. For HMSS, the martensitic transformation takes place at some isolated areas with a slow nucleation rate.

  16. Stationary and quasistationary models of carbon redistribution in austenitic steel weldments: II. Polycomponent systems

    NASA Astrophysics Data System (ADS)

    Kučera, Jar; Kozák, V.; Million, B.; Stránský, K.

    1986-04-01

    In this IInd part of our paper (Czech. J. Phys. B 35 (1985) 1355) the analysis of carbon uphill diffusion data is presented. The analysed data were measured in the polycomponent steel weldments. All of the data satisfy well the conditions for stationary model application. On the basis of the present analysis the carbon diffusivities ( D {1/*}) appertaining to a non-alloyed austenite, the activity (ɛ{C/s}) and diffusion ( β {C/s}) interaction coefficients are evaluated. A “Si anomaly” in Darken's experiments is observed and discussed. On the contrary to the other substitutional elements Mn, Cr and Mo, which decrease simultaneously C-activity and C-diffusivity, silicon increases the carbon activity and, at the same time, decreases its diffusivity in the Fe-C-Xs austenitic solid solutions.

  17. Influences of carbon and silicon on blister formation in scale surface during high temperature oxidation of carbon steels

    NASA Astrophysics Data System (ADS)

    Kim, Deuk-Jung; Lee, Jae-Sang; Koo, Yang-Mo

    2017-07-01

    The in-situ blistering phenomena of the scale `surface' was investigated on three carbon steels with respect to carbon and silicon concentrations, such as 0.05 wt%C, 0.2 wt%C, and 0.2 wt%C-0.2 wt%Si. The oxidation and blistering kinetics and blister area fraction during high temperature oxidation were analyzed. The average thickness of the surface scale by oxidation during isothermal holding from 800 to 1200 °C in dry air was observed to decrease when the amount of carbon increased and/or when Si was inserted additionally. Thus, the blistering behavior depended primarily on a change in oxidation temperature ( T ox ) as well as amounts of carbon and silicon in the matrix. It is also revealed that such blister formation would be triggered by growth of internal stress and active generations of CO and/or CO2 gases at the interface between the scale and matrix since carbon would result in an increase in the blister formation by generating CO and/or CO2 gas. In addition, silicon might play an important role in preventing the blister formation at T ox below 900 °C by reducing the thickness of the surface scale whilst silicon might enhance the blister formation by means of the appreciable micro-void formation in the scale layer at T ox higher 900 °C.

  18. Effect of the electrolyte composition on the corrosion of 12Kh17 steel in molten alkali metal carbonates

    NASA Astrophysics Data System (ADS)

    Nikitina, E. V.

    2017-02-01

    The corrosion of 12Kh17 steel in the melts of alkali metal carbonates containing additions of various chemical types is studied using anodic potentiostatic polarization. The morphology of the 12Kh17 steel surface is analyzed by electron-probe microanalysis. The introduction of corrosion passivators and activators affects the mechanism of local corrosion damages. The corrosion of the steel proceeds according to an electrochemical mechanism. Carbonate anions serve as oxidizers of the steel along with oxygen dissolved in the melt. Treatment of a corrosive medium can be used to protect metallic constructions against corrosion in high-temperature salt electrolytes. Combined introduction of corrosion activators and passivators in a salt phase makes it possible to form protective layers with a high corrosion resistance.

  19. Understanding dual precipitation strengthening in ultra-high strength low carbon steel containing nano-sized copper precipitates and carbides

    NASA Astrophysics Data System (ADS)

    Phaniraj, M. P.; Shin, Young-Min; Jung, Woo-Sang; Kim, Man-Ho; Choi, In-Suk

    2017-07-01

    Low carbon ferritic steel alloyed with Ti, Mo and Cu was hot rolled and interrupt cooled to produce nano-sized precipitates of copper and (Ti,Mo)C carbides. The steel had a tensile strength of 840 MPa, an increase in yield strength of 380 MPa over that of the plain carbon steel and reasonable ductility. Transmission electron microscopy and small angle neutron scattering were used to characterize size and volume fraction of the precipitates in the steels designed to form only copper precipitates and only (Ti,Mo)C carbides. The individual and combined precipitation strengthening contributions was calculated using the size and volume fraction of precipitates and compared with the measured values.

  20. Stability of retained austenite in high carbon steel under compressive stress: an investigation from macro to nano scale

    NASA Astrophysics Data System (ADS)

    Hossain, R.; Pahlevani, F.; Quadir, M. Z.; Sahajwalla, V.

    2016-10-01

    Although high carbon martensitic steels are well known for their industrial utility in high abrasion and extreme operating environments, due to their hardness and strength, the compressive stability of their retained austenite, and the implications for the steels’ performance and potential uses, is not well understood. This article describes the first investigation at both the macro and nano scale of the compressive stability of retained austenite in high carbon martensitic steel. Using a combination of standard compression testing, X-ray diffraction, optical microstructure, electron backscattering diffraction imaging, electron probe micro-analysis, nano-indentation and micro-indentation measurements, we determined the mechanical stability of retained austenite and martensite in high carbon steel under compressive stress and identified the phase transformation mechanism, from the macro to the nano level. We found at the early stage of plastic deformation hexagonal close-packed (HCP) martensite formation dominates, while higher compression loads trigger body-centred tetragonal (BCT) martensite formation. The combination of this phase transformation and strain hardening led to an increase in the hardness of high carbon steel of around 30%. This comprehensive characterisation of stress induced phase transformation could enable the precise control of the microstructures of high carbon martensitic steels, and hence their properties.