Groundwater maintenance at the vulcan materials quarry in Chattanooga, Tennessee

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, R.L.

1985-01-01

The Vulcan Materials Shallowford Road Quarry in Chattanooga, Tennessee is the largest active limestone quarry in the state. Currently it covers some 35 hectares with highwalls up to 100 m. Production is predominately from Middle Ordovician Limestone of the Stones River Group. The upper 60 m consists of medium-bedded gray limestone of the Pond Springs Formation, while the lower 40 m are in Lower Ordovician dolomites and limestones belonging to the Mascot Formation of the Knox Group. The present quarry began in 1951 and has been in continuous operation since that time. For several years the influx of groundwater intomore » the quarry was so great that over 11,355 liters per minute had to be removed by a series of pumps. A source of much of the groundwater was thought to be from Friar Branch which flowed near the present quarry site. At low water, several sinkholes were observed in the bottom of the stream. Several attempts were made (unsuccessfully) to fill these sinks. On July 17, 1984, a 184 m trench was dug along the north side of Friar Branch and fifty-one sections of 1.2 m diameter pipe were placed in the trench. Each 4 m section was made water tight and the water from Friar branch was then diverted into the pipe. Bulldozers scraped the dry bed of Friar Branch in an attempt to locate all major cavities and sinkholes. These were filled with grout and the bed of the creek was covered with about 7 to 8 cm of crushed rock and rolled. The entire stream was sealed with grout and then the stream was returned to its original course. The results was a marked reduction in groundwater seepage into the quarry.« less

The Ançã limestones, Coimbra, Portugal

NASA Astrophysics Data System (ADS)

Quinta-Ferreira, Mário; Gil Catarino, Lídia; Delgado Rodrigues, José

2016-04-01

. Most of the traditional quarries are abandoned and those still in activity are mainly used to produce crushed aggregates, limestone blocks for paving produced in a quite artisanal way, and more rarely for sculpture. The identification and characterization of the variability of the Ançã limestones, as well as the inventory of the existing quarries and outcrops are necessary to preserve this unique resource, important for the preservation and rehabilitation of several monuments and artwork, in Coimbra, classified as UNESCO Word Heritage, where Ançã limestones, including the Pedra de Ançã, were extensively used.

Sinkhole development induced by underground quarrying, and the related hazard

NASA Astrophysics Data System (ADS)

Parise, M.; Delle Rose, M.

2009-04-01

Sinkholes are extremely widespread in Apulia, a very flat and carbonate region, that acted as the foreland during the phases of building up of the Southern Apenninic Chain in Miocene time. This is due to the presence of soluble rocks throughout the region, that highly predispose the area to this very subtle natural hazard. In addition to the natural setting, which favours their development, sinkholes may also be induced by anthropogenic activities. In the latter sense, underground quarrying represents one of the most dangerous activities in karst areas. Apulia has a long history of quarrying. Since the roman time, the local rocks, from the Cretaceous micritic limestones to the Quaternary calcarenites, have been intensely quarried and used as building and ornamental materials. In several settings of the region, the rocks with the best petrographic characteristics are located at depths ranging from a few to some tens of meters. This caused the opening of many underground quarries, and the development of a complex network of subterranean galleries. Underground quarrying had a great impulse at the turn between the XIX and the XX century, when a large number of quarries was opened. Later on, after the Second World War, most of the quarries were progressively abandoned, even because of the first signs of instability, both underground and at the ground surface. With time, the memory of the presence and development of the underground quarries was progressively lost, with severe repercussions on the safety of the land above the excavated areas. Lack of knowledge of the subterranean pattern of galleries, combined with the expansion of the built-up areas at the surface, resulted in increasing significantly the vulnerability of exposed elements at risk. Events such as the 29 March, 2007, at Gallipoli only by chance did not result in any casualties, when a 15-mt wide and 5-mt deep sinkhole opened in a few hours at a road crossing, above the site of an old underground quarry

Drenov Grič black limestone as a heritage stone from Slovenia

NASA Astrophysics Data System (ADS)

Kramar, Sabina; Rožič, Boštjan; Žbona, Nina; Bedjanič, Mojca; Mladenović, Ana

2016-04-01

The limestone known as Drenov Grič black limestone is considered one of the most beautiful Slovenian natural stones due to its homogenous black colour interwoven with white veins. Over the centuries it has been exploited from three major quarries west of Ljubljana, with the main quarry at Drenov Grič playing the primary role in supplying building material for the central parts of Slovenia. All the quarries are currently not active. In the area of Drenov grič, one locality of black limestone is protected - Kuclerjev kamnolom quarry. It has the status of 'valuable natural feature of national importance' and is protected as a natural monument. This well-stratified micritic limestone of Triassic (Carnian) age occurs in 10-80 cm thick beds, with thin marl interlayers. The stone contains abundant fossil bivalves and ostracods. Apart from calcite as the main component, dolomite, quartz, illite/muscovite and pyrite are also present. The limestone is relatively rich in carbonaceous and bituminous organic matter, which is responsible for the black colour of the stone. This component does not have any adverse effect on mechanical and physical characteristics. As the lime¬stone is dense, thus facilitating a good polish, it has been commercially considered as marble. The stone has been widely used in Slovenian monuments, not only in Ljubljana but also in other regions of Slovenia. Many inner and outdoor architectural elements were made of this limestone, particularly in the baroque period, which was known for the extensive use of black limestones also in other European countries. The most significant use of this limestone has been recorded in sculptured portals and altars. Some of the important buildings decorated utilising this stone, are the Ljubljana Cathedral, the St. James's Parish Church, and the Franciscan Church of the Annunciation, all of which are located in Ljubljana, some of them having been declared as cultural monuments of local or national importance. When

Geology of the Carnegie museum dinosaur quarry site of Diplodocus carnegii, Sheep Creek, Wyoming

USGS Publications Warehouse

Brezinski, D.K.; Kollar, A.D.

2008-01-01

The holotype of Diplodocus carnegii Hatcher, 1901, consists of a partial skeleton (CM 84) that was recovered, along with a second partial skeleton of the same species (CM 94), from the upper 10 m of the Talking Rock facies of the Brushy Basin Member of the Morrison Formation exposed along Bone Quarry Draw, a tributary of Sheep Creek in Albany County, Wyoming. A composite measured section of the stratigraphic interval exposed adjacent to the quarry indicates that the Brushy Basin Member in this area is a stacked succession of lithofacies consisting of hackly, greenish gray, calcareous mudstone and greenish brown, dense, fine-grained limestone. The more erosion resistant limestone layers can be traced over many hundreds of meters. Thus, these strata do not appear to represent a highly localized deposit such as a stream channel, oxbow lake, or backwater pond. The Sheep Creek succession is interpreted as representing a clastic-dominated lake where high turbidity and sediment influx produced deposition of calcareous mudstone. During drier periods the lake's turbidity decreased and limestone and dolomite precipitation replaced mud deposition. Microkarsting at the top of some limestone/ dolomite layers suggests subaerial deposition may have prevailed during these dry episodes. The quarry of D. carnegii was excavated within the top strata of one of the numerous intervals of hackly, greenish gray, calcareous mudstone that represent an ephemeral freshwater lake. The quarry strata are directly overlain by 0.3 m of dolomite-capped limestone that was deposited shortly after interment of D. carnegii in the lake mudstones. The close vertical proximity of the overlying limestone to the skeleton's stratigraphic: level suggests that the animal's carcass may have been buried beneath the drying lake deposits during a period of decreased rainfall.

Quarries as educational resources - a research with students of a secondary school of Portugal

NASA Astrophysics Data System (ADS)

Filipe, Fernanda; Henriques, Maria Helena

2015-04-01

This work describes the results obtained in a research on science education involving 18 students of Biology and Geology of the 10th grade (15 years old) of the Secondary School of Figueiró dos Vinhos (Central Portugal). Framed on the curricular topic "Earth, a very special planet", the research included the conception, implementation and evaluation of an educational intervention aiming to answer the question: "How to stimulate meaningful and relevant learning about sustainable exploitation of geological resources, namely limestone?" The intervention occurred along 8 classes of 90 minutes each, which included practical work developed in small groups (3 students/each), and several activities both in the field and in the classroom (prior and after the fieldtrip). From the methodological point of view, this research is qualitative in nature, a study-case type, with data resulting from direct observation and content analysis of the answers presented by students to questionnaires (diagnostic and intervention assessment) and to worksheets, expressly created for the research. The main goal of the intervention was that the students, by developing practical activities centered upon a field trip to an abandoned limestone quarry located close to their homes, could learn to recognize the geological impacts arising from the exploitation of geological resources and acquire skills for collecting and processing relevant information about existing rules that control the operations in quarries, in order to develop critical thinking about the nature of exploitation of these types of resources, which may hinder the promotion of sustainable development. Concerning the intervention assessment, results reinforced the idea that quarries can provide an educational resource of great value for promoting substantive knowledge on geosciences, urgently needed and consistent with the development of critical and intervenient citizens, able to decide, at the right moment, how to behave

Contribution in support of a Global Heritage Stone designation for the Leitha Limestone s.l. of eastern Austria because of its use in Roman times

NASA Astrophysics Data System (ADS)

Moshammer, Beatrix; Rohatsch, Andreas

2015-04-01

The Leitha Limestone s.l., which has been proposed for Global Heritage Stone listing, comprises the red algae dominated sediments of shallow water carbonate platforms distributed around the Leitha Mountains, the Ruster Hills and other parts of the Vienna Basin. In our sense it comprehends the Leithakalk faciostratotype of the Badenian regional stage along with its lateral equivalents of near shore calcareous sandstones, breccias and conglomerates. It also includes the so called detrital Leithakalk, an informal name for calcareous algae sandstones of the Sarmatian regional stage that is perhaps comparable with the Skalica Formation and finally it covers the algae strata known from the Pannonian regional stage. Thus the Leitha Limestone s.l. belongs to the middle and upper part of the Miocene, i.e. ranging from about 16 to 10 my BP. The geoscientific focus of this multidisciplinary research is on deciphering the petrological types and carbonate facies of stone monuments and building stones and on comparing them with the successions of the strata outcropping in abandoned quarries. We are recording distinguishing lithological features and collecting appropriate field samples for microscopic, petrophysical, and geochemical analysis. The results of these analyses will be used to characterise the different varieties of Leitha Limestone s.l. of the investigated stone objects, with a view to setting up a catalogue based on lithological types that could be of considerable value for restoration and conservation too. Carnuntum was the regional metropolis of the Roman province Pannonia Superior and one of the legionary camps along the Danube Limes from about 40 AD to the end of the 5th century. It is situated about 40 km east of Vienna city centre, in the present-day market-town of Petronell-Carnuntum. Most of the stone objects from Carnuntum are made of the local quarried Leitha Limestone s.l. from the Hainburg Mountains and from ancient quarries in the Leitha Mountains

STEAM ENHANCED REMEDIATION RESEARCH FOR DNAPL IN FRACTURED ROCK, LORING AIR FORCE BASE, LIMESTONE, MAINE

EPA Science Inventory

This report details a research project on Steam Enhanced Remediation (SER) for the recovery of volatile organic compounds from fractured limestone that was carried out at the Quarry at the former Loring Air Force Base in Limestone, Maine. This project was carried out by USEPA, Ma...

Limestone - A Crucial and Versatile Industrial Mineral Commodity

USGS Publications Warehouse

Bliss, James D.; Hayes, Timothy S.; Orris, Greta J.

2008-01-01

Limestone, as used by the minerals industry, is any rock composed mostly of calcium carbonate (CaCO3). Although limestone is common in many parts of the United States, it is critically absent from some. Limestone is used to produce Portland cement, as aggregate in concrete and asphalt, and in an enormous array of other products, making it a truly versatile commodity. Portland cement is essential to the building industry, but despite our Nation's abundance of limestone, there have been cement shortages in recent years. These have been caused in part by a need to find new areas suitable for quarrying operations. To help manage our Nation's resources of such essential mineral commodities, the U.S. Geological Survey (USGS) provides crucial data and scientific information to industry, policymakers, and the public.

Biocalcifying Bacillus subtilis cells effectively consolidate deteriorated Globigerina limestone.

PubMed

Micallef, Roderick; Vella, Daniel; Sinagra, Emmanuel; Zammit, Gabrielle

2016-07-01

Microbially induced calcite precipitation occurs naturally on ancient limestone surfaces in Maltese hypogea. We exploited this phenomenon and treated deteriorated limestone with biocalcifying bacteria. The limestone was subjected to various mechanical and physical tests to present a statistically robust data set to prove that treatment was indeed effective. Bacillus subtilis conferred uniform bioconsolidation to a depth of 30 mm. Drilling resistance values were similar to those obtained for freshly quarried limestone (9 N) and increased up to 15 N. Treatment resulted in a high resistance to salt deterioration and a slow rate of water absorption. The overall percentage porosity of treated limestone varied by ±6 %, thus the pore network was preserved. We report an eco-friendly treatment that closely resembles the mineral composition of limestone and that penetrates into the porous structure without affecting the limestones' natural properties. The treatment is of industrial relevance since it compares well with stone consolidants available commercially.

Cretaceous planktic foraminiferal biostratigraphy of the Calera Limestone, Northern California, USA

USGS Publications Warehouse

Sliter, W.V.

1999-01-01

The Calera Limestone is the largest, most stratigraphically extensive limestone unit of oceanic character included in the Franciscan Complex of northern California. The aim of this paper is to place the Calera Limestone at its type locality (Rockaway Beach, Pacifica) in a high-resolution biostratigraphy utilizing planktic foraminifers studied in thin section. A section, about 110 m-thick, was measured from the middle thrust slice exposed by quarrying on the southwest side of Calera Hill at Pacifica Quarry. Lithologically, the section is divided in two units; a lower unit with 73 m of black to dark-grey limestone, black chert and tuff, and an upper unit with 36.8 m of light-grey limestone and medium-grey chert. Two prominent black-shale layers rich in organic carbon occur 11 m below the top of the lower black unit and at the boundary with overlying light-grey unit, yielding a total organic content (TOC) of 4.7% and 1.8% t.w., respectively. The fossiliferous Calera Limestone section measured at Pacifica Quarry, from the lower black shale, contains eleven zones and three subzones that span approximately 26 m.y. from the early Aptian to the late Cenomanian. The zones indentified range from the Globigerinelloides blowi Zone to the Dicarinella algeriana Subzone of the Rotalipora cushmani Zone. Within this biostratigraphic interval, the Ticinella bejaouaensis and Hedbergella planispira Zones at the Aptian/Albian boundary are missing as are the Rotalipora subticinensis Subzone of the Biticinella breggiensis Zone and the overlying Rotalipora ticinensis Zone in the late Albian owing both to low-angle thrust faulting and to unconformities. The abundance and preservation of planktic foraminifers are poor in the lower part and improve only within the upper G. algerianus Zone. The faunal relationship indicate that the lower black shale occurs in the upper part of the G. blowi Zone and correlates with the Selli Event recognized at global scale in the early Aptian. The upper black

A methodological framework to assess the socio-economic impact of underground quarries: A case study from Belgian Limburg.

PubMed

Sergeant, A; Poesen, J; Duchateau, P; Vranken, L

2016-01-15

This study developed a methodology to assess the socio-economic impact of the presence and collapse of underground limestone quarries. For this we rely on case study evidence from Riemst, a village located in Eastern Belgium and use both secondary and primary data sources. A sinkhole inventory as well as data about the prevention costs provided by the municipality was used. To estimate the recreational values of the quarries, visitor data was obtained from the tourist office of Riemst. Next, two surveys were conducted among inhabitants and four real estate agents and one notary. The direct and indirect damages were assessed using respectively the repair cost and production and real estate value losses. The total yearly direct and indirect damage equals €415000 (±€85000) and more than half of it can be attributed to the depreciation of real estate (€230000). The quarries have recreational, cultural-historical and ecological values and thus generate societal benefits. The yearly recreational value was at least €613000 in 2012 values. The ecological and cultural-historical values augment to €180000 per year (in 2012 values). Further, our study indicates that the gains from filling up the quarries below the houses located above an underground limestone quarry outweigh the costs in the case study area. The net gain from filling up the underground quarry ranges €38700 to €101700 per house. This is only the lower bound of the net gain from filling up these underground quarries since preventive filling makes future collapses less likely so that future direct repair costs will be most likely smaller. Copyright © 2015 Elsevier B.V. All rights reserved.

Introducing a new aspect in marble quarry rehabilitation in Greece

NASA Astrophysics Data System (ADS)

Kaliampakos, D. C.; Mavrikos, A. A.

2006-06-01

For many years the marble extraction sector of the Greek mining industry has been in conflict with the public, especially in terms of rehabilitation of marble quarry sites. One of the main reasons for that is that the marble extraction sector has been unable to adjust to the existing legislative guidelines for the rehabilitation, such as extensive backfilling and re-vegetation. In the majority of cases these methods fail due to erosion of the backfill soil and adverse climatic conditions. As a result the number of abandoned marble quarry sites is continuously increasing. The present paper suggests a different approach regarding the rehabilitation of marble quarries. More specifically, the paper questions the applicability, the effectiveness, and the social usefulness of the above-mentioned guidelines and suggests the establishment of new land-uses, which are based on an in-depth analysis of the area’s special features, by taking full advantage of its potentials. What is more, the rehabilitation scheme proposes that the new land-uses and the quarrying activity may co-exist and operate simultaneously for a long period of time.

Use Of limestone resources in flue-gas desulfurization power plants in the Ohio River Valley

USGS Publications Warehouse

Foose, M.P.; Barsotti, A.F.

1999-01-01

In 1994, more than 41 of the approximately 160 coal-fired, electrical- power plants within the six-state Ohio River Valley region used flue-gas desulfurization (FGD) units to desulfurize their emissions, an approximately 100% increase over the number of plants using FGD units in 1989. This increase represents a trend that may continue with greater efforts to meet Federal Clean Air Act standards. Abundant limestone resources exist in the Ohio River Valley and are accessed by approximately 975 quarries. However, only 35 of these are believed to have supplied limestone for FGD electrical generating facilities. The locations of these limestone suppliers do not show a simple spatial correlation with FGD facilities, and the closest quarries are not being used in most cases. Thus, reduction in transportation costs may be possible in some cases. Most waste generated by FGD electrical-generating plants is not recycled. However, many FGD sites are relatively close to gypsum wallboard producers that may be able to process some of their waste.

Analysis of medieval limestone sculpture from southwestern France and the Paris Basin by NAA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holmes, L.; Harbottle, G.

1994-12-31

Compositional characterization of limestone from sources known to medieval craftsmen and from the monuments they built can be used in conjunction with stylistic and iconographic criteria to infer geographic origin of sculptures that have lost their histories. Limestone from 47 quarrying locations in France and from numerous medieval monuments have been subjected to neutron activation analysis (NAA) to form the nucleus of the Brookhaven Limestone Database. Even though the method and techniques of NAA are well established, this paper briefly summarizes the parameters and experimental conditions useful for determining those concentration variables for which limestone from different sources exhibits significantmore » and reproducible differences.« less

77 FR 10472 - San Bernardino National Forest, Mountaintop Ranger District, California, Mitsubishi South Quarry...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-22

... Cushenbury Cement Plant. Concurrent reclamation would be conducted throughout the life of the quarry and, at... the lead state agency under the California Environmental Quality Act (CEQA), address specific... grades of limestone to meet the feed requirement for the cement plant would not be adequate for the life...

Geochemistry, environmental and provenance study of the Middle Miocene Leitha limestones (Central Paratethys)

NASA Astrophysics Data System (ADS)

Ali, Ahmed; Wagreich, Michael

2017-06-01

Mineralogical, major, minor, REE and trace element analyses of rock samples were performed on Middle Miocene limestones (Leitha limestones, Badenian) collected from four localities from Austria (Mannersdorf, Wöllersdorf, Kummer and Rosenberg quarries) and the Fertőrákos quarry in Hungary. Impure to pure limestones (i.e. limited by Al2O3 contents above or below 0.43 wt. %) were tested to evaluate the applicability of various geochemical proxies and indices in regard to provenance and palaeoenvironmental interpretations. Pure and impure limestones from Mannersdorf and Wöllersdorf (southern Vienna Basin) show signs of detrital input (REEs = 27.6 ± 9.8 ppm, Ce anomaly = 0.95 ± 0.1 and the presence of quartz, muscovite and clay minerals in impure limestones) and diagenetic influence (low contents of, e.g., Sr = 221 ± 49 ppm, Na is not detected, Ba = 15.6 ± 8.8 ppm in pure limestones). Thus, in both limestones the reconstruction of original sedimentary palaeoenvironments by geochemistry is hampered. The Kummer and Fertőrákos (Eisenstadt-Sopron Basin) comprise pure limestones (e.g., averages Sr = 571 ± 139 ppm, Na = 213 ± 56 ppm, Ba = 21 ± 4 ppm, REEs = 16 ± 3 ppm and Ce anomaly = 0.62 ± 0.05 and composed predominantly of calcite) exhibiting negligible diagenesis. Deposition under a shallow-water, well oxygenated to intermittent dysoxic marine environment can be reconstructed. Pure to impure limestones at Rosenberg-Retznei (Styrian Basin) are affected to some extent by detrital input and volcano-siliciclastic admixture. The Leitha limestones at Rosenberg have the least diagenetic influence among the studied localities (i.e. averages Sr = 1271 ± 261 ppm, Na = 315 ± 195 ppm, Ba = 32 ± 15 ppm, REEs = 9.8 ± 4.2 ppm and Ce anomaly = 0.77 ± 0.1 and consist of calcite, minor dolomite and quartz). The siliciclastic sources are characterized by immobile elemental ratios (i.e. La/Sc and Th/Co) which apply not only for the siliciclastics, but also for marls and

Age and correlation of the Calera Limestone in the Permanente terrane of northern California

USGS Publications Warehouse

Sliter, William V.; McGann, Mary

1992-01-01

Planktonic foraminifers indicate that outcrops of Calera Limestone from the Permanente terrane in the Franciscan Complex of northern California range in age from possibly as old as Barremian to late Turonian. Underlying black limestone, which is devoid of planktonic foraminifers, presumably is Barremian in age or older. The top of the sequence exposed in major quarries is always faulted. Improved biostratigraphic resolution shows two patterns of missing time intervals. The primary pattern, which is found at all localities and involves missing planktonic foraminiferal zones in the late Aptian to early Albian and the late Albian, is linked to paleoceanographic changes in the Cretaceous Pacific Ocean. The secondary pattern, which is found at the scattered outcrops outside the major quarries and involves missing zones in the Albian and Cenomanian, suggests the results of a common tectonic history related to the accretion of a large seamount.

Paleocene orthophragminids from the Lakadong Limestone, Mawmluh Quarry section, Meghalaya (Shillong, NE India): implications for the regional geology and paleobiogeography

NASA Astrophysics Data System (ADS)

Özcan, Ercan; Pignatti, Johannes; Pereira, Christer; Osman Yücel, Ali; Drobne, Katica; Barattolo, Filippo; Saraswati, Pratul Kumar

2018-04-01

The late Paleocene orthophragminids, hitherto poorly known from the Himalayan foreland basins, are studied from the Lakadong Limestone in Meghalaya, northeastern India, in order to establish a systematic, biostratigraphic, and paleobiogeographical framework for them in the eastern Tethys. In the Mawmluh Quarry section (MQS) on the Shillong Plateau, to the southeast of Tibet, orthophragminids are associated with typical Paleocene orbitoidiform taxa endemic to the Indian subcontinent, i.e., Lakadongia Matsumaru & Jauhri ( = Setia Ferràndez-Cañadell) and Orbitosiphon Rao, and various species of alveolinids, miscellaneids, and rotaliids, characterizing the Shallow Benthic Zones (SBZ) 3 and 4. The orthophragminids belong to two lineages of the genus Orbitoclypeus Silvestri: O. schopeni (Checchia-Rispoli) and O. multiplicatus (Gümbel), both well known from the peri-Mediterranean region and Europe (western Tethys). The latter species is identified here for the first time from the eastern Tethys. Previous records of the genus Discocyclina Gümbel from the Lakadong Limestone actually correspond to misidentified Orbitoclypeus; this implies that the late Paleocene orthophragminid assemblages from Meghalaya and eastern Tethys were less diverse than in the western Tethys. The lineage of Orbitoclypeus schopeni in the lower part of the Lakadong Limestone (SBZ 3) is identified as O. schopeni cf. ramaraoi based on the morphometry of a few specimens, whereas in the upper part (SBZ 4) it corresponds to a transitional development stage between O. schopeni ramaraoi and O. schopeni neumannae (with average Dmean values ranging between 192 and 199 µm). The embryon diameters of O. multiplicatus, recorded only in SBZ 4, range between 300 and 319 µm on average, corresponding to transitional development stages of O. multiplicatus haymanaensis and O. multiplicatus multiplicatus. Our data, along with a review of previous Paleocene and Eocene records from India and Pakistan, suggest

INTERIOR VIEW, NORTH QUARRY, AN ACTIVE DOLOMITE QUARRY, LOOKING NORTH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, NORTH QUARRY, AN ACTIVE DOLOMITE QUARRY, LOOKING NORTH TO THE POWER PLANT OF THE HISTORIC THOMAS COKEWORKS SITE. - Wade Sand & Gravel Company, North Quarry, State Highway 78, Thomas, Jefferson County, AL

Comparative study of porous limestones used in heritage structures in Cyprus and in Hungary

NASA Astrophysics Data System (ADS)

Theodoridou, Magdalini; Ioannou, Ioannis; Rozgonyi-Boissinot, Nikoletta; Török, Ákos

2015-04-01

Porous limestone is widely used as construction material in the monuments of Cyprus and Hungary. The present study compares the physical properties of a bioclastic limestone from Cyprus and an oolitic limestone from Hungary. Petra Gerolakkou is a Pliocene limestone from Cyprus that originates from the district of Nicosia, the island's capital. It has been extensively used throughout the years in construction and restoration projects, particularly in the Nicosia area. Distinctive examples of its use can be found in the majority of the most important historic monuments in Nicosia, such as the Venetian walls and fortifications, churches (e.g. the Agia Sofia Cathedral), the archbishop and presidential palaces and a high number of other traditional buildings. The studied Miocene limestone from Hungary was exploited from Sóskút quarry (15-20 km W-SW to Budapest). The quarry provided stone for emblematic monuments of the capital of Hungary such as the Parliament building, Mathias Church, the Opera House and Citadella. In this study, mechanical parameters for both aforementioned stones, such as uniaxial compressive and tensile strengths, were tested under laboratory conditions. Their density, porosity and water absorption were also compared. The studied limestone from Cyprus exhibits porosity values within the range of 48-51%, apparent density between 1340 and 1400 kg/m3 and strength values under uniaxial compressive load between 1.2 and 2.8 MPa. This lithotype is also considered susceptible to salt decay, since an approximate mass loss of 12.5% is noted after 15 salt crystallization artificial weathering cycles. The porosity of the Hungarian limestone is in the order of 16-35%, the bulk density is 1600-1950 kg/m3, while the compressive strength is 2.5-15 MPa. Durability tests indicate that even after 10 freeze-thaw cycles the loss in strength is dramatic. Test results indicate that use of porous limestone in both countries is common and fabric strongly controls the

Total organic carbon and humus fractions in restored soils from limestone quarries in semiarid climate, SE Spain

NASA Astrophysics Data System (ADS)

Luna Ramos, Lourdes; Miralles Mellado, Isabel; Ángel Domene Ruiz, Miguel; Solé Benet, Albert

2016-04-01

Mining activities generate erosion and loss of plant cover and soil organic matter (SOM), especially in arid and semiarid Mediterranean regions. A precondition for ecosystem restoration in such highly disturbed areas is the development of functional soils with sufficient organic matter. But the SOM quality is also important to long-term C stabilization. The resistance to biodegradation of recalcitrant organic matter fractions has been reported to depend on some intrinsic structural factors of humic acid substances and formation of amorphous organo-mineral recalcitrant complexes. In an experimental soil restoration in limestone quarries in the Sierra de Gádor (Almería), SE Spain, several combinations of organic amendments (sewage sludge and compost from domestic organic waste) and mulches (gravel and woodchip) were added in experimental plots using a factorial design. In each plot, 75 native plants (Anthyllis cytisoides, A. terniflora and Macrochloa tenacissima) were planted and five years after the start of the experiment total organic carbon (TOC), physico-chemical soil properties and organic C fractions (particulate organic matter, H3PO4-fulvic fraction, fulvic acids (FA), humic acids (HA) and humin) were analyzed. We observed significant differences between treatments related to the TOC content and the HA/FA ratio. Compost amendments increased the TOC, HA content and HA/FA ratio, even higher than in natural undisturbed soils, indicating an effective clay humus-complex pointing to progressively increasing organic matter quality. Soils with sewage sludge showed the lowest TOC and HA/FA ratio and accumulated a lower HA proportion indicating poorer organic matter quality and comparatively lower resilience than in natural soils and soils amended with compost.

AERIAL VIEW, LOOKING NORTHWEST TOWARDS JONES VALLEY FROM THE CREST ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

AERIAL VIEW, LOOKING NORTHWEST TOWARDS JONES VALLEY FROM THE CREST OF RED (CALLED RUFFNER) MOUNTAIN AND THE CITY OF BIRMINGHAM (TOP), WITH ABANDONED SLOSS CO. LIMESTONE QUARRIES (CENTER) AND RIGHT-OF-WAY OF THE L. & N. BIRMINGHAM MINERAL RAILROAD (LEFT CENTER TO BOTTOM RIGHT). - Ruffner Red Ore Mine, North of I-20 at Madrid Exit, Birmingham, Jefferson County, AL

Response of the soil physical properties to restoration techniques in limestone quarries

NASA Astrophysics Data System (ADS)

Luna Ramos, Lourdes; Miralles Mellado, Isabel; Vignozzi, Nadia; Solé-Benet, Albert

2016-04-01

The devastating effects of soil erosion in mining areas from arid/semiarid environments have prompted efforts geared toward an improvement of the soil physical conditions for a fast establishment of vegetal cover. Restoration practices that increase soil moisture content are essential in drylands where rainfall is irregular or insufficient in order to accelerate ecological restoration. The aim of this study was to analyse the influence of organic amendments and mulches on the soil porosity as well as their impact on infiltration, five years after the beginning of an experimental restoration from limestone quarries in Sierra de Gádor (Almería, SE Spain). Nine plots 15 x 5 m were prepared at the site in a completely randomized 2 x 3 factorial design. The first factor, organic amendment, had three levels: sewage sludge (SA), compost from domestic organic residues (CA) and no amendment (NA). The second factor, mulches, also had three levels: gravel (GM), woodchip (WM) and no mulch (NM). In each experimental plot 75 native plants (Macrochloa tenacissima, Anthyllis terniflora and Anthyllis cytisoides) were planted. Infiltration was determined from rainfall simulations and soil porosity was assessed by image analysis of soil thin sections. Total porosity and pores distribution were measured according to pore shape (regular, irregular and elongated) and size (transmission pores [50-500 μm] and fissures [>500 μm]). Natural undisturbed soils around the mine area were used as a reference soil (RS). Restoration treatments showed higher total porosity, fissures and elongated pores than RS and we observed the highest values in treatments with WM. This fact is due to the disruption caused by the application of treatments rather that a good soil structure. Each combination exhibited different values of transmission pores, being greater in the combinations of NA-GM, SA-NM and CA-WM. Infiltration increased with the increase of the total porosity, fissures and elongated pores

Piedramuelle Limestone in the building heritage of Oviedo, Spain, and adjacent towns.

NASA Astrophysics Data System (ADS)

Cardenes Van den Eynde, Victor; Mateos, Felix Javier; Valdeon, Luis; Rojo, Araceli

2017-04-01

The Piedramuelle limestone has a very important representation in the building heritage of Oviedo, historical capital of Asturias (Spain) and surrounding towns. This argillaceous limestone has been quarried since the High Middle Ages until the beginning of the XX century. The main mineralogical components are carbonates (mainly calcite and sometimes ankerite, 70-90%), quartz (5-15%), terrigenous minerals (6-15%) and iron oxides (<5%). Two different facies, with different constructive uses, can be clearly distinguished depending on the grain size: fine-grained facies and coarse-grained facies. The fine-grained facies has color ranging from red to yellow, slightly higher content in carbonates, higher terrigenous components and a micro crystalline texture. The coarse-grained facies is mainly yellow, with detrital clastic texture. The open porosity is higher for the coarse-grained facies (16-20%), while for the fine-grained facies it ranges between 5 and 15%. The fine-grained facies is more vulnerable to weathering than the coarse-grained one, and it is used in the building heritage mainly for ornamental details, while the coarse-grained one is found in the bigger blocks and ashlars of the buildings. Some of the buildings constructed with Piedramuelle limestone are the Cathedral, the Old University and the Palaces from the XVII and XVIII centuries. The ambiance and historical architecture of Oviedo and adjacent towns is closely linked with the textures and colors of this stone. Nowadays, the Piedramuelle limestone is not exploited anymore, being the quarries exhausted. This represents an issue from a conservation point of view, since there is not a suitable stone for replacement. In order to preserve and maintain the building heritage of these towns, it is very important to prospect and protect the remaining outcrops still able to supply this characteristic stone.

Identification of Quarries Rehabilitation Scenarios: A Case Study Within the Metropolitan Area of Bari (Italy)

NASA Astrophysics Data System (ADS)

Dal Sasso, Pasquale; Ottolino, Maria Antonella; Caliandro, Lucia Patrizia

2012-06-01

This paper addresses quarries rehabilitation issue within a Metropolitan Area. Areas where mining activity is carried out have been subjected to physical and environmental degradation linked both to pursue the building materials extraction and to the city expansion continuously asking for new areas to be developed with residential and service functions. These changes also occurred where environmental and landscape values are present. It has been therefore pointed out the issue of such areas redevelopment that, to be functionally reintegrated, must be consistently linked to the activities and the territorial local contexts characteristics. In this paper the quarries reuse issue is carried out through parameters identification able to define the quarries relationship with the neighboring towns and with their surroundings besides to identify their physical, environmental and landscaping characteristics. Quarry reuse alternatives have been identified among those consistent with the rehabilitation goals, as defined by the planning sector and internationally approved, while their selection is derived from the application of a two-step methodology: a multi-criteria analysis related to punctual parameters at a "site-specific" level, followed by a further territorial indicators checking over the wide area. This application has led to socially accepted results identifying the examined quarries for reuses ranging from agricultural-forestry and urban to functional or naturalistic. The proposed method has also proved to be suitable to address the abandoned quarries reuse problem with a systemic and consultative approach, as it is able to correlate the many variables present in the social and spatial complexity of the Metropolitan Areas.

Flue gas desulfurization chemistry studies: limestone grindability. Volume 1. FGD reagent mapping. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richmann, D.L.; Rossi, J.P.; Rashin, E.B.

1984-07-01

The major objective of this project is to provide electric utilities with information concerning the availability of flue gas desulfurization (FGD) system reagents. Data presented in this report were obtained primarily from a comprehensive review of available literature. These were augmented by information gathered through interviews with knowledgeable individuals from industry, government, and academic institutions. Limestone data are presented on regional and state maps displaying, respectively, annual limestone production and number of active quarries by county; and areas most likely to contain potentially commercial deposits of high-Ca (greater than or equal to 90% CaCO/sub 3/) limestone. Lime data are presentedmore » on regional maps indicating ranges of annual production and number of active lime plants by county. Identification of commercial versus captive operations and estimates of lime availability on the open market are summarized in tables accompanying each map.« less

Multidisciplinary studies on ancient sandstone quarries of Western Sardinia (Italy).

NASA Astrophysics Data System (ADS)

Grillo, Silvana Maria; Del Vais, Carla; Naitza, Stefano

2013-04-01

, Oristano, Santa Giusta). They are prevailing fine-medium grained carbonate sandstones, and subordinate coarse sandstones and micro-conglomerates, variably cemented. In the studied areas, stratigraphic sequences grade from coarser facies of marine environment to fine-grained aeolian deposits, marked by cross-stratification. The Quaternary sedimentary sequence rests on Miocene limestones and clays, and on Plio-Pleistocene basalts. On optical microscopy, sandstones show grain-supported texture, with abundant carbonate bioclasts, intraclasts and algal nodules, with quartz, feldspars and fragments of granitoids, quartzites, volcanics. Grainsize in sandstone sequences progressively decreases towards the top, corresponding to an increase of fine bioclastic components. Terrigenous components change from the northernmost outcrops (Is Arutas quarries), where clasts of granitoid origin are dominant, to the southern outcrops (San Giovanni di Sinis quarries), which show a more marked compositional heterogeneity, with frequent volcanic feldspars and lithoclasts. The calcitic cement also shows distinct variations, both along the stratigraphic sequence and at areal scale, between the sparitic type and the micro/cryptocrystalline type. First evidences on samples from Tharros city walls indicate that sandstone blocks may come, almost in part, from the quarries of San Giovanni di Sinis that, consequently, could have started to work during the Punic age. Other evidences in the area, however, indicate that quarrying activities in Sinis continued well over the Ancient times, presumably including all the Middle Ages.

EFFECT OF AN ACID RAIN ENVIRONMENT ON LIMESTONE SURFACES.

USGS Publications Warehouse

Mossotti, Victor G.; Lindsay, James R.; Hochella, Michael F.

1987-01-01

Salem limestone samples were exposed to weathering for 1 y in several urban and one rural environments. Samples exposed in the rural location were chemically indistinguishable from the freshly quarried limestone, whereas all samples collected from urban exposure sites developed gypsum stains on the ground-facing surfaces where the stones were not washed by precipitation. The gas-solid reaction of SO//2 with calcite was selected for detailed consideration. It appears from the model that under arid conditions, the quantity of stain deposited on an unwashed surface is independent of atmospheric SO//2 concentration once the surface has been saturated with gypsum. Under wet conditions, surface sulfation and weight loss are probably dominated by mechanisms involving wet stone. However, if the rain events are frequent and delimited by periods of dryness, the quantity of gypsum produced by a gas-solid reaction mechanism should correlate with both the frequency of rain events and the atmospheric SO//2 level.

Norwegian millstone quarry landscapes

NASA Astrophysics Data System (ADS)

Heldal, Tom; Meyer, Gurli; Grenne, Tor

2013-04-01

Rotary querns and millstones were used in Norway since just after the Roman Period until the last millstone was made in the 1930s. Throughout all this time millstone mining was fundamental for daily life: millstones were needed to grind grain, our most important food source. We can find millstone quarries in many places in the country from coast to mountain. Some of them cover many square kilometers and count hundreds of quarries as physical testimonies of a long and great production history. Other quarries are small and hardly visible. Some of this history is known through written and oral tradition, but most of it is hidden and must be reconstructed from the traces we can find in the landscape today. The Millstone project has put these quarry landscapes on the map, and conducted a range of case studies, including characterization of archaeological features connected to the quarrying, interpretation of quarrying techniques and evolution of such and establishing distribution and trade patterns by the aid of geological provenance. The project also turned out to be a successful cooperation between different disciplines, in particular geology and archaeology.

Probabilistic prediction models for aggregate quarry siting

USGS Publications Warehouse

Robinson, G.R.; Larkins, P.M.

2007-01-01

Weights-of-evidence (WofE) and logistic regression techniques were used in a GIS framework to predict the spatial likelihood (prospectivity) of crushed-stone aggregate quarry development. The joint conditional probability models, based on geology, transportation network, and population density variables, were defined using quarry location and time of development data for the New England States, North Carolina, and South Carolina, USA. The Quarry Operation models describe the distribution of active aggregate quarries, independent of the date of opening. The New Quarry models describe the distribution of aggregate quarries when they open. Because of the small number of new quarries developed in the study areas during the last decade, independent New Quarry models have low parameter estimate reliability. The performance of parameter estimates derived for Quarry Operation models, defined by a larger number of active quarries in the study areas, were tested and evaluated to predict the spatial likelihood of new quarry development. Population density conditions at the time of new quarry development were used to modify the population density variable in the Quarry Operation models to apply to new quarry development sites. The Quarry Operation parameters derived for the New England study area, Carolina study area, and the combined New England and Carolina study areas were all similar in magnitude and relative strength. The Quarry Operation model parameters, using the modified population density variables, were found to be a good predictor of new quarry locations. Both the aggregate industry and the land management community can use the model approach to target areas for more detailed site evaluation for quarry location. The models can be revised easily to reflect actual or anticipated changes in transportation and population features. ?? International Association for Mathematical Geology 2007.

Radon-222 signatures of natural ventilation regimes in an underground quarry.

PubMed

Perrier, Frédéric; Richon, Patrick; Crouzeix, Catherine; Morat, Pierre; Le Mouël, Jean Louis

2004-01-01

Radon-222 activity concentration has been monitored since 1999 in an underground limestone quarry located in Vincennes, near Paris, France. It is homogeneous in summer, with an average value of 1700 Bq m(-3), and varies from 730 to 1450 Bq m(-3) in winter, indicating natural ventilation with a rate ranging from 0.5 to 2.4 x 10(-6) s(-1) (0.04-0.22 day(-1)). This hypothesis is supported by measurements in the vertical access pit where, in winter, a turbulent air current produces a stable radon profile, smoothly decreasing from 700 Bq m(-3) at 20 m depth to 300 Bq m(-3) at surface. In summer, a thermal stratification is maintained in the pit, but the radon-222 concentration jumps repeatedly between 100 and 2000 Bq m(-3). These jumps are due to atmospheric pressure pumping, which induces ventilation in the quarry at a rate of about 0.1 x 10(-6) s(-1) (0.009 day(-1)). Radon-222 monitoring thus provides a dynamical characterisation of ventilation regimes, which is important for the assessment of the long-term evolution of underground systems.

Characterizing the microbial colonization of a dolostone quarry: implications for stone biodeterioration and response to biocide treatments.

PubMed

Cámara, Beatriz; De los Ríos, Asuncion; Urizal, Marta; de Buergo, Mónica Alvarez; Varas, Maria Jose; Fort, Rafael; Ascaso, Carmen

2011-08-01

This study examines the microbial colonization of three fronts of an abandoned dolostone quarry (Redueña, Madrid, Spain) exposed to atmospheric conditions for different time periods since Roman times to the present. Through scanning electron microscopy in backscattered electron mode (SEM-BSE), endolithic colonization was predominantly detected in the most recently exposed front, while in the longer exposed quarry fronts, epilithic forms of growth were most often observed. These observations were confirmed by denaturing gradient gel electrophoresis (DGGE) analysis. Based on the distribution pattern of microbial colonization in the different quarry fronts, we then established a sequence of colonization events that took place over this long time frame. Bioalteration processes related to this sequential colonization were also identified. Characterizing these sequential processes can be useful for interpreting biodeterioration processes in historic dolostone monuments, especially those affecting constructions in the area of the Redueña stone quarry. In a second experimental stage, different biocide treatments were tested on this quarry rock to find the best way to avoid the microbial colonization effects identified. Through combined SEM-BSE/DGGE analysis, the efficacy of several biocides against the microorganisms inhabiting the dolostones was assessed after 4 and 16 months treatment. In general, all treatments were effective at reducing around 80% of the lichen cover, although effects on endolithic lithobiontic communities were dependent on how well the rock surface had been mechanically cleaned prior to treatment and gradually disappeared over time.

Using stable isotopes (δD, δ18O, δ34S and 87Sr/86Sr) to identify sources of water in abandoned mines in the Fengfeng coal mining district, northern China

NASA Astrophysics Data System (ADS)

Qu, Shen; Wang, Guangcai; Shi, Zheming; Xu, Qingyu; Guo, Yuying; Ma, Luan; Sheng, Yizhi

2018-05-01

With depleted coal resources or deteriorating mining geological conditions, some coal mines have been abandoned in the Fengfeng mining district, China. Water that accumulates in an abandoned underground mine (goaf water) may be a hazard to neighboring mines and impact the groundwater environment. Groundwater samples at three abandoned mines (Yi, Er and Quantou mines) in the Fengfeng mining district and the underlying Ordovician limestone aquifer were collected to characterize their chemical and isotopic compositions and identify the sources of the mine water. The water was HCO3·SO4-Ca·Mg type in Er mine and the auxiliary shaft of Yi mine, and HCO3·SO4-Na type in the main shaft of Quantou mine. The isotopic compositions (δD and δ18O) of water in the three abandoned mines were close to that of Ordovician limestone groundwater. Faults in the abandoned mines were developmental, possibly facilitating inflows of groundwater from the underlying Ordovician limestone aquifers into the coal mines. Although the Sr2+ concentrations differed considerably, the ratios of Sr2+/Ca2+ and 87Sr/86Sr and the 34S content of SO4 2- were similar for all three mine waters and Ordovician limestone groundwater, indicating that a close hydraulic connection may exist. Geochemical and isotopic indicators suggest that (1) the mine waters may originate mainly from the Ordovician limestone groundwater inflows, and (2) the upward hydraulic gradient in the limestone aquifer may prevent its contamination by the overlying abandoned mine water. The results of this study could be useful for water resources management in this area and other similar mining areas.

Surface wave inversion of central Texas quarry blasts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bonner, J.L.; Goforth, T.T.

1993-02-01

Compressional and shear wave models of the upper crust in central Texas were obtained by inverting Rayleigh and Love waves recorded at the new W.M. Keck Foundation Seismological Observatory at Baylor University. The Keck Observatory, which became operational in April 1992, consists of a three-component, broadband Geotech seismometer located at a depth of 130 feet in a borehole 17 miles from the Baylor campus. The field station is solar powered, and the 140-dB dynamic range digital data are transmitted to the Baylor analysis lab via radio, where they are analyzed and archived. Limestone quarries located in all directions from themore » Keck Observatory detonate two to four tons of explosives per blast several times a week. Recordings of these blasts show sharp onsets of P and S waves, as well as dispersed Rayleigh and Love waves in the period band 1 to 3 seconds. Multiple filter analysis and phase matched filtering techniques were used to obtain high quality dispersion curves for the surface waves, and inversion techniques were applied to produce shear velocity models of the upper crust. A rapid increase in shear velocity at a depth of about 1.5 km is associated with the Ouachita Overthrust Belt. Portable seismic recording systems were placed at the quarries to monitor start times and initial wave forms. These data were combined with the Keck recordings to produce attenuation and compressional velocity models.« less

Diversity and biogeography of land snails (Mollusca, Gastropoda) in the limestone hills of Perak, Peninsular Malaysia

PubMed Central

Foon, Junn Kitt; Clements, Gopalasamy Reuben; Liew, Thor-Seng

2017-01-01

Abstract Limestone hills are now gaining global conservation attention as hotspots for short-range endemic species. Levels of land snail endemism can be high at limestone hills, especially at hill clusters that are geographically isolated. In the State of Perak, Peninsular Malaysia, limestone hills have been opportunistically surveyed for land snails in the past, but the majority have yet to be surveyed. To address this knowledge gap, we systematically surveyed the terrestrial malacofauna of 12 limestone hills that, based on our opinion, are a representation of the limestone land snail assemblages within the State. Our inventory yielded high sampling completeness (>85%). We found 122 species of land snails, of which 34 species were unique to one of the surveyed hills. We identified 30 species that are potentially new to science. The number of land snail species recorded at each hill ranged between 39 and 63 species. Four of the sampled limestone hills namely, Prk 01 G. Tempurung, Prk 55 G. Pondok, Prk 47 Kanthan, and Prk 64 Bt Kepala Gajah, have high levels of species richness and unique species, representing 91% of the total species recorded in this study. We identified two clusters of limestone hills in central Perak with distinct differences in land snail species composition – a northern hill cluster on elevated granite bedrock and southern hill cluster in a low-lying valley surrounded by alluvial soils. As limestone hills continue to be quarried to meet the cement demand, the four identified limestone hills, along with other hills from the two clusters, warrant urgent conservation attention in order to maintain high species diversity within Perak’s terrestrial malacofauna. PMID:28769723

Colmenar limestone as a resource for built heritage

NASA Astrophysics Data System (ADS)

Fort, Rafael; Álvarez de Buergo, Mónica; Varas-Muriel, MªJosé; Mercedes Pérez-Monserrat, Elena

2013-04-01

The Colmenar stone (or Colmenar limestone) has been used in the construction of significant builidings of the Central area of Spain, such as the Royal Palace of Aranjuez (16th -18th centuries) or the Royal Palace of Madrid (18th century). Nowadays this building stone is still widely used, both for new construction and restoration works, as well as for the indoor ornamentation of emblematic buildings such as the Royal Theater of Madrid (20th century). There are many quarries from where this stone was exploited, being the most prestigious ones those located in Colmenar de Oreja, at 50 km Southeast the city of Madrid. The high quality of the stone in these quarries, its whiteness and pureness, made this locality the most relevant in these stonés extractive activities, concentrating the most relevant exploitations and providing the stone the denomination of the municipality (Colmenar). It was an underground mining extraction until the 20th century in order to reach the highest quality level of the mine, the so called "Banco Gordo" (Thick Bank). Generically known as moorland limestone, this rock belongs to the fluvial-lacustrine carbonates of the Upper Miocene Unit of the Tertiary Madrid's Basin. Its tonality mainly ranges from white to cream and even light grey. Under a petrographic point of view, this limestone is constituted by 40% of bioclasts (characea, ostracods and gasteropods), 20-30% of micritic matrix and 30-40% of sparitic cement. Therefore, it can be classified as a biomicrite/biosparite limestone or as a bioclastic packstone. Some particularities of these limestones regarding their appearance are related to some karstic processes they underwent linked to some dissolution phenomena during the Pliocene. All of this resulted on an abundance of cavities with terra rossa fillings, a non-soluble clayey residue, iron enriched, which is the responsible for the reddish and pinkish color that the Colmenar stone sometimes shows. These petrographic characteristics

Use of a Combination of Vertical and Horizontal Boreholes in Massive Blasting of Benches in the Surface Quarry Rodež

NASA Astrophysics Data System (ADS)

Tori, Matija; Vajović, Stanojle; Goleš, Niko; Muhić, Elvir; Peternel, Miha

2017-12-01

This article deals with the extraction of minerals (limestone/marl/flysch) in the quarry Rodež, which is located in western Slovenia. During the extraction of minerals in a quarry, drilling and blasting of benches are used. The focus of the article is on the analysis of the parameters related to drilling and blasting in surface excavations when using a combination of explosions and introducing horizontal wells along with vertical holes in the bench. On the basis of the analysis of basic parameters through a combination of drilling horizontal wells and charging those with the ammonal + Anfex explosive, analyses of effects of seismic disturbances on potentially affected buildings have also been conducted. The article is connected to and deals exclusively with the basic parameters of drilling and blasting, with the introduction of horizontal drilling and with the analysis of seismic measurements of threatened buildings in accordance with the German standard German Institute for Standardisation (DIN) 4150 during the use of a new method of blasting.

Assessing the role of coastal characteristics in erosional process of rocky shores by boulder quarrying.

NASA Astrophysics Data System (ADS)

Causon Deguara, Joanna; Gauci, Ritienne

2017-04-01

Rocky coasts are considered as relatively stable coastlines, subject to erosional processes that change the landscape over long periods of time. Block quarrying is one such process, occurring when hydraulic pressure from wave impact dislodges boulders from within the outcropping bedrock. These dislodged boulders can be either deposited inland or dragged seaward by further wave action. This process can be evidenced from boulder deposits on the coast, as well as sockets and detachment scarps that are identified at the shoreline and in the backshore. This study seeks to identify the role of attributes such as aspect, geological structure and water depth have on erosion of rocky coasts through boulder quarrying processes. This is being done through observation of coastline morphology and an analysis of boulder accumulations and erosional features identified on a 3km stretch of rocky shore. The study area is situated on the SE coast of the Island of Malta (Central Mediterranean). The coastline being analysed generally trends NW - SE and consists of a series of limestone beds that dip slightly towards the NE. The boulder deposits observed along the site vary in size, quantity and position with respect to the shoreline. Whilst some areas exhibit large boulder accumulations, other areas are distinguished by the complete absence of such deposits. Taking into consideration the wave climate, the variable size, quantity and distribution of boulder accumulations observed along the site may indicate that geological structure and aspect play an important role in boulder dislodgment by wave action. Key words: rock coast, boulder quarrying, erosional process, Malta

Performance of portland limestone cements: Cements designed to be more sustainable that include up to 15% limestone addition

NASA Astrophysics Data System (ADS)

Barrett, Timothy J.

In 2009, ASTM and AASHTO permitted the use of up to 5% interground limestone in ordinary portland cement (OPC) as a part of a change to ASTM C150/AASHTO M85. When this work was initiated a new proposal was being discussed that would enable up to 15% interground limestone cement to be considered in ASTM C595/AASHTO M234. This work served to provide rapid feedback to the state department of transportation and concrete industry for use in discussions regarding these specifications. Since the time this work was initiated, ASTM C595/AASHTO M234 was passed (2012c) and PLCs are now able to be specified, however they are still not widely used. The proposal for increasing the volume of limestone that would be permitted to be interground in cement is designed to enable more sustainable construction, which may significantly reduce the CO2 that is embodied in the built infrastructure while also extending the life of cement quarries. Research regarding the performance of cements with interground limestone has been conducted by the cement industry since these cements became widely used in Europe over three decades ago, however this work focuses on North American Portland Limestone Cements (PLCs) which are specifically designed to achieve similar performance as the OPCs they replace.This thesis presents a two-phase study in which the potential for application of cements containing limestone was assessed. The first phase of this study utilized a fundamental approach to determine whether cement with up to 15% of interground or blended limestone can be used as a direct substitute to ordinary portland cement. The second phase of the study assessed the concern of early age shrinkage and cracking potential when using PLCs, as these cements are typically ground finer than their OPC counterparts. For the first phase of the study, three commercially produced PLCs were obtained and compared to three commercially produced OPCs made from the same clinker. An additional cement was tested

Hydrothermal karst and associated breccias in Neoproterozoic limestone from the Barker-Villa Cacique area (Tandilia belt), Argentina

NASA Astrophysics Data System (ADS)

Dristas, Jorge A.; Martínez, Juan C.; van den Kerkhof, Alfons M.; Massonne, Hans-Joachim; Theye, Thomas; Frisicale, María C.; Gregori, Daniel A.

2017-07-01

In the Barker-Villa Cacique area (Tandilia belt), remarkable megabreccias, limestone breccias and phosphate-bearing breccias hosted in black limestone and along the contact with the upper section of the sedimentary succession are exposed. These rocks are the result of extensive hydrothermal alteration of the original micritic limestone and other fine-grained clastic sediments. Typical alteration minerals are sericite, chlorite, interstratified chlorite/K-white mica, kaolinite, dickite, pyrite, chalcopyrite, goethite, quartz, calcite, Fe-calcite, dolomite, ankerite, fluor-apatite, barite and aluminium-phosphate-sulfate (APS) minerals. Quartz and calcite cements from hydraulic breccias in the limestone contain low-salinity aqueous fluid inclusions. Corresponding homogenization temperatures display 200-220 °C and 110-140 °C in hydrothermal quartz, and 130-150 °C in late calcite cement. Carbon and oxygen stable isotope analyses of carbonates from the Loma Negra quarry (LNQ) support the major role of hydrothermal activity. A significant difference was found between δ18Ocar values from unaltered micritic limestone (ca. 23.8‰ SMOW) and secondary calcite (ca. 18.5‰ SMOW). The lower δ18Ocar values are interpreted as a result of calcite precipitation from hot hydrothermal fluids. At a late stage, the hydrothermal fluid containing H2S mixed with descending and oxidizing meteoric waters. Circulation of the ensuing acid fluids resulted in the partly dissolution and collapse brecciation of the Loma Negra Formation. The hydrothermal stage can be tentatively dated ca. 590-620 Ma corresponding to the Brasiliano orogeny.

Nomination of the Globigerina Limestone of the Maltese Islands as a "Global Heritage Stone Resource"

NASA Astrophysics Data System (ADS)

Cassar, JoAnn

2016-04-01

The Maltese Islands consist of two main islands, Malta and Gozo, as well as a small number of islets, and lie in the central Mediterranean Sea approximately 90 km south of Sicily. Although only 316 square kilometres in size, the Islands contain a rich concentration of archaeological sites and historic buildings, as well as vernacular architecture and modern buildings, for the most part built of the local Globigerina Limestone, which is one of the few natural resources of the Islands. This stone can be described as a typical "soft limestone", very easy to carve and shape. It forms part of the large family of Oligo-Miocene "soft limestones" widely diffused in the Mediterranean Basin. The Maltese Globigerina Limestone Formation is one of five main Formations, and varies in thickness from 20 to over 200 m. The material used for building is located stratigraphically in the lower part of the Globigerina Limestone Formation, called the Lower Globigerina Limestone. This Formation is stratified into thick beds at outcrop. Sections where bioturbation is concentrated often also occur. This limestone is fine-grained, yellow to pale grey in colour, almost wholly composed of the tests of globigerinid planktonic foraminifera. Petrographically, Globigerina Limestone can be described as a bioclastic packstone, with bioclastic wackestones also occurring. This limestone has always been used as the predominant building material in the Islands. The Maltese prehistoric Temples, which were constructed approximately 6000 years ago, bear testimony to this. Between 1530 and 1798 the Order of the Knights of St John built kilometres of fortifications in this same material to protect the Island from the expanding Ottoman Empire. Fortifications, impressive churches, auberges and palaces were built of this stone during this period. The capital city of Valletta, a rich and dense manifestation of Baroque architecture in Globigerina Limestone, is included on the UNESCO World Heritage List, as are

DOSAGE DES ELEMENTS EN TRACE DES CALCAIRES AU SERVICE DE L'ARCHEOLOGIE

DOE Office of Scientific and Technical Information (OSTI.GOV)

BLANC,A.; HOLMES,L.; HARBOTTLE,G.

1998-05-01

Numerous quarries in the Lutetian limestone formations of the Paris Basin provided stone for the building and the decoration of monuments from antiquity to the present. To determine the origin of stone used for masonry and sculptures in these monuments, a team of geologists and archaeologists has investigated 300 quarries and collected 2,300 samples. Petrographic and paleontologic examination of thin sections allows geologists to distinguish Lutetian limestones from Jurassic and Cretaceous limestones. Geologists also seek to formulate hypotheses regarding the origin of Lutetian limestones used for building and sculpture in the Paris region. In the search for the sources ofmore » building and sculptural stone, the analytical methods of geologists are limited because often several quarries produce the same lithofacies. A new tool is now available, however, to attack questions of provenance raised by art historians. Because limestones from different sources have distinctive patterns of trace-element concentrations, compositional analysis by neutron activation allows them to compare building or sculptural stone from one monument with stone from quarries or other monuments. This analytical method subjects a powdered limestone sample to standard neutron activation analysis procedures at Brookhaven National Laboratory. With the help of computer programs, the compositional fingerprints of Lutetian limestones can be determined and stored in a database. The limestone database contains data for approximately 2,100 samples from monuments, sculptures and quarries. It is particularly rich in samples from the Paris Basin.« less

OVERALL VIEW OF QUARRY, FACING NORTH, WITH UNQUARRIED GRANITE OUTCROP ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

OVERALL VIEW OF QUARRY, FACING NORTH, WITH UN-QUARRIED GRANITE OUTCROP IN BACKGROUND - Granite Hill Plantation, Quarry No. 3, South side of State Route 16, 1.3 miles northeast east of Sparta, Sparta, Hancock County, GA

Blasting methods for heterogeneous rocks in hillside open-pit mines with high and steep slopes

NASA Astrophysics Data System (ADS)

Chen, Y. J.; Chang, Z. G.; Chao, X. H.; Zhao, J. F.

2017-06-01

In the arid desert areas in Xinjiang, most limestone quarries are hillside open-pit mines (OPMs) where the limestone is hard, heterogeneous, and fractured, and can be easily broken into large blocks by blasting. This study tried to find effective technical methods for blasting heterogeneous rocks in such quarries based on an investigation into existing problems encountered in actual mining at Hongshun Limestone Quarry in Xinjiang. This study provided blasting schemes for hillside OPMs with different heights and slopes. These schemes involve the use of vertical deep holes, oblique shallow holes, and downslope hole-by-hole sublevel or simultaneous detonation techniques. In each bench, the detonations of holes in a detonation unit occur at intervals of 25-50 milliseconds. The research findings can offer technical guidance on how to blast heterogeneous rocks in hillside limestone quarries.

Pump Hydro Energy Storage systems (PHES) in groundwater flooded quarries

NASA Astrophysics Data System (ADS)

Poulain, Angélique; de Dreuzy, Jean-Raynald; Goderniaux, Pascal

2018-04-01

Pump storage hydroelectricity is an efficient way to temporarily store energy. This technique requires to store temporarily a large volume of water in an upper reservoir, and to release it through turbines to the lower reservoir, to produce electricity. Recently, the idea of using old flooded quarries as a lower reservoir has been evoked. However, these flooded quarries are generally connected to unconfined aquifers. Consequently, pumping or injecting large volumes of water, within short time intervals, will have an impact on the adjacent aquifers. Conversely, water exchanges between the quarry and the aquifer may also influence the water level fluctuations in the lower reservoir. Using numerical modelling, this study investigates the interactions between generic flooded open pit quarries and adjacent unconfined aquifers, during various pump-storage cyclic stresses. The propagation of sinusoidal stresses in the adjacent porous media and the amplitude of water level fluctuations in the quarry are studied. Homogeneous rock media and the presence of fractures in the vicinity of the quarry are considered. Results show that hydrological quarry - rock interactions must be considered with caution, when implementing pump - storage systems. For rock media characterized by high hydraulic conductivity and porosity values, water volumes exchanges during cycles may affect significantly the amplitude of the water level fluctuations in the quarry, and as a consequence, the instantaneous electricity production. Regarding the impact of the pump - storage cyclic stresses on the surrounding environment, the distance of influence is potentially high under specific conditions, and is enhanced with the occurrence of rock heterogeneities, such as fractures. The impact around the quarry used as a lower reservoir thus appears as an important constraining factor regarding the feasibility of pump - storage systems, to be assessed carefully if groundwater level fluctuations around the quarry

Environmental risk evaluation of the use of mine spoils and treated sewage sludge in the ecological restoration of limestone quarries

NASA Astrophysics Data System (ADS)

Jordán, M. M.; Pina, S.; García-Orenes, F.; Almendro-Candel, M. B.; García-Sánchez, E.

2008-07-01

The ecologic restoration criteria in areas degraded from extraction activities require making use of their mine spoils. These materials do not meet fertility conditions to guarantee restoration success and therefore, need the incorporation of organic amendments to obtain efficient substratum. Reducing the deficiencies in the organic material and restoration material nutrients with the contribution of treated sewage sludge is proposed in this work. This experiment was based on a controlled study using columns. The work was conducted with two mine spoils, both very rich in calcium carbonate. The first mineral, of poor quality, came from the formation of aggregates of crushed limestone ( Z). The other residual material examined originated in limestone extraction, formed by the levels of interspersed non-limestone materials and the remains of stripped soils ( D). Two treatments were undertaken (30,000 and 90,000 kg/ha of sewage sludge), in addition to a control treatment. The water contribution was carried out with a device that simulated either short-duration rain or a flooding irrigation system in order to cover the surface and then percolate through the soil. The collection of leached water took place 24 h after the applications. Different parameters of the leached water were determined, including pH, electrical conductivity, nitrate anions, ammonium, phosphates, sulphates and chlorides. The values obtained for each irrigation application are discussed, and the nitrate values obtained were very elevated.

Landscape evolution by subglacial quarrying

NASA Astrophysics Data System (ADS)

Ugelvig, Sofie V.; Egholm, David L.; Iverson, Neal R.

2014-05-01

In glacial landscape evolution models, subglacial erosion rates are often related to basal sliding or ice discharge by a power-law. This relation can be justified for bedrock abrasion because rock debris transported in the basal ice drives the erosion. However, a simple relation between rates of sliding and erosion is not well supported when considering models for quarrying of rock blocks from the bed. Iverson (2012) introduced a new subglacial quarrying model that operates from the theory of adhesive wear. The model is based on the fact that cavities, with a high level of bedrock differential stress, form along the lee side of bed obstacles when the sliding velocity is to high to allow for the ice to creep around the obstacles. The erosion rate is quantified by considering the likelihood of rock fracturing on topographic bumps. The model includes a statistical treatment of the bedrock weakness: larger rock bodies have lower strengths since they have greater possibility of containing a large flaw [Jaeger and Cook, 1979]. Inclusion of this effect strongly influences the erosion rates and questions the dominant role of sliding rate in standard models for subglacial erosion. Effective pressure, average bedslope, and bedrock fracture density are primary factors that, in addition to sliding rate, influence the erosion rate of this new quarrying model [Iverson, 2012]. We have implemented the quarrying model in a depth-integrated higher-order ice-sheet model [Egholm et al. 2011], coupled to a model for glacial hydrology. In order to also include the effects of cavitation on the subglacial sliding rate, we use a sliding law proposed by Schoof (2005), which includes an upper limit for the stress that can be supported at the bed. Computational experiments show that the combined influence of pressure, sliding rate and bed slope leads to realistically looking landforms such as U-shaped valleys, cirques, hanging valleys and overdeepenings. Compared to model results using a

Deep Impact Spots Quarry

NASA Image and Video Library

2005-04-27

Taken on April 25, 2005, sixty-nine days before it gets up-close-and-personal with a comet, NASA Deep Impact spacecraft successfully photographed its quarry, comet Tempel 1, at a distance of 39.7 million miles.

Experimental method for estimation of compaction in the Oxfordian bedded limestones of the southern Kraków-Częstochowa Upland, Southern Poland

NASA Astrophysics Data System (ADS)

Kochman, Alicja; Matyszkiewicz, Jacek

2013-12-01

Kochman, A. and Matyszkiewicz, J. 2013. Experimental method for estimation of compaction in the Oxfordian bedded limestones of the southern Krakow-Częstochowa Upland, Southern Poland. Acta Geologica Polonica, 63(4), 681-696. Warszawa. The Upper Jurassic carbonates exposed in the southern part of the Krakow-Częstochowa Upland are well known for their significant facies diversity related to the presence of microbial and microbial-sponge carbonate buildups and bedded detrital limestone in between. Both the buildups and detrital limestones revealed differential susceptibility to compaction which, apart from differential subsidence of the Palaeozoic basement and synsedimentary faulting, was one of the factors controlling seafloor palaeorelief in the Late Jurassic sedimentary basin. The compaction of the detrital limestones has been estimated with an experimental oedometric method in which specially prepared mixtures made of ground limestones from a quarry in the village of Żary were subjected to oedometer tests. The diameters of the detrital grains and their percentages in the limestones were determined by microscopic examinations of thin sections. The diameters were assigned to predetermined classes corresponding to the Udden-Wentworth scale. The rock samples were then ground down to the grain sizes observed in thin sections. From such materials, mixtures were prepared of grain size distributions corresponding to those observed in thin sections. After adding water the mixtures were subjected to oedometer tests. Analysis of the compression of such mixtures under specific loads enabled preparation of a mathematical formula suitable for the estimation of mechanical compaction of the limestone. The obtained values varied from 27.52 to 55.53% for a load corresponding to 300 metres burial depth. The most significant effect of mechanical compaction was observed for loads representing only 2 metres burial depth. Further loading resulted in a much smaller

Strength Characteristics of Quarry Dust in Replacement of Sand

NASA Astrophysics Data System (ADS)

Shyam Prakash, K.; Hanumantha Rao, Ch, Dr

2017-08-01

The replacement of natural fine aggregate by using quarry dust leads to consumption of generated quarry dust, the requirement of land fill area can be reduced and solves the natural sand scarcity problem. The sand availability as a fine aggregate at low cost which needs the reason to search as a alternative material. Even it causes saddle to dump the crusher dust at one place which causes environmental pollution. The chemical analysis, specific gravity, sieve analysis and compressive strength is identified for various percentage and grades of concrete by replacement of sand with quarry dust.

The Öland limestone - A Swedish stone used for more than one thousand years

NASA Astrophysics Data System (ADS)

Schouenborg, Björn; Wickström, Linda; Mikaelsson, Jan

2016-04-01

�landic limestone was intense even during Hanseatic times (14th to 17th centuries) and it can for example be found as floorings, mantel pieces, baptismal fonts in many German castles and manors. The literature tells us that export to Denmark, Poland and even southern Germany was intense during late medieval ages. This is because a lot of churches were built in Northern Europe at that time. However, the modern industrialised production had to wait until the early 20th century. Today, three companies quarry and process the limestones on a regular basis. They are primarily used for flooring, stairs, crazy stones for gardens, table tops, kitchen tops and, in some cases, also external cladding and paving. The latter only with more durable layers free of clay and open stylolites, so called "core stone" (direct translation). The presentation will show that the Öland limestone covers all aspects and requirements for being a Global heritage resource.

INTERIOR VIEW, NORTH QUARRY, LOOKING NORTH TOWARDS THE SITE OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, NORTH QUARRY, LOOKING NORTH TOWARDS THE SITE OF THE HISTORIC THOMAS FURNACES WITH ACTIVE DOLOMITE EXTRACTION ONGOING IN THE FOREGROUND. FURNACE FOUNDATION RUINS ARE PICTURED ON THE TOP LEDGE (CENTER LEFT) OF THE QUARRY. ALSO PICTURED IS THE HISTORIC THOMAS COKEWORKERS WITH (LEFT TO RIGHT) THE POWER PLANT, BOILER HOUSE, AND COKEWORKS. JUST SOUTH OF THE COKEWORKS, IS AN ACTIVE DOLOMITE CRUSHING, SIZING, AND SCREENING PLANT - Wade Sand & Gravel Company, North Quarry, State Highway 78, Thomas, Jefferson County, AL

INTERIOR VIEW, NORTH QUARRY, LOOKING NORTH TOWARDS THE SITE OF ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, NORTH QUARRY, LOOKING NORTH TOWARDS THE SITE OF THE HISTORIC THOMAS FURNACES WITH ACTIVE DOLOMITE EXTRACTION ONGOING IN THE FOREGROUND. FURNACE FOUNDATION RUINS ARE PICTURED ON THE TOP LEDGE (CENTER LEFT) OF THE QUARRY. ALSO PICTURED IS THE HISTORIC THOMAS COKEWORKS WITH (LEFT TO RIGHT) THE POWER PLANT, BOILER HOUSE, AND COKEWORKS. JUST SOUTH OF THE COKEWORKS IS AN ACTIVE DOLOMITE CRUSHING, SIZING, AND SCREENING PLANT. - Wade Sand & Gravel Company, North Quarry, State Highway 78, Thomas, Jefferson County, AL

Use of Borehole-Radar Methods to Monitor a Steam-Enhanced Remediation Pilot Study at a Quarry at the Former Loring Air Force Base, Maine

USGS Publications Warehouse

Gregoire, Colette; Joesten, Peter K.; Lane, John W.

2007-01-01

Single-hole radar reflection and crosshole radar tomography surveys were used in conjunction with conventional borehole-geophysical methods to evaluate the effectiveness of borehole-radar methods for monitoring the movement of steam and heat through fractured bedrock. The U.S. Geological Survey, in cooperation with U.S. Environmental Protection Agency (USEPA), conducted surveys in an abandoned limestone quarry at the former Loring Air Force Base during a field-scale, steam-enhanced remediation (SER) pilot project conducted by the USEPA, the U.S. Air Force, and the Maine Department of Environmental Protection to study the viability of SER to remediate non-aqueous phase liquid contamination in fractured bedrock. Numerical modeling and field experiments indicate that borehole-radar methods have the potential to monitor the presence of steam and to measure large temperature changes in the limestone matrix during SER operations. Based on modeling results, the replacement of water by steam in fractures should produce a decrease in radar reflectivity (amplitude of the reflected wave) by a factor of 10 and a change in reflection polarity. In addition, heating the limestone matrix should increase the bulk electrical conductivity and decrease the bulk dielectric permittivity. These changes result in an increase in radar attenuation and an increase in radar-wave propagation velocity, respectively. Single-hole radar reflection and crosshole radar tomography data were collected in two boreholes using 100-megahertz antennas before the start of steam injection, about 10 days after the steam injection began, and 2 months later, near the end of the injection. Fluid temperature logs show that the temperature of the fluid in the boreholes increased by 10?C (degrees Celsius) in one borehole and 40?C in the other; maximum temperatures were measured near the bottom of the boreholes. The results of the numerical modeling were used to interpret the borehole-radar data. Analyses of the

View of four large bore holes on top of quarry ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of four large bore holes on top of quarry wall, facing northeast - Granite Hill Plantation, Quarry No. 4, South side of State Route 16, 1.3 miles northeast east of Sparta, Sparta, Hancock County, GA

Air quality assessment on human well-being in the vicinity of quarry site

NASA Astrophysics Data System (ADS)

Ibrahim, W. H. W.; Marinie, E.; Yunus, J.; Asra, N.; Sukor, K. Mohd

2018-02-01

This study aims to investigate the variation of air pollutants associated with the quarry activities prior to classified distance from quarry site. Air pollutants were monitored with the use of instruments which are Rae System Multirae Lite Pumped (PGM-6208) to measure indoor air quality while TSI 8533 Dusttrack Drx Desktop Aerosol Monitor to measure outdoor air quality. Sampling will be replicated two times. The locations of quarry are at Bandar Saujana Putra and Taman Kajang Perdana 2, Selangor. The objectives of this study are to investigate the impact of quarry mining by preparing the suitable Indoor Air Quality Index and to prepare preventive measure for residential that caused from quarry mining activities. Both Qualitative and Quantitative approaches will be implemented in this study, which employed case study and interview survey. Both quarries identified previously will be the main case study. The Respondent’s interviews are from Local Authority and Quarry Management Staff while questionnaire surveys from selected residences. Measurement method will be used to measure the Particle Matter (PM2.5) for indoor and outdoor in selected resident’s area. However, this paper is primed to discuss the method used in this study. It is not only presents the beneficial information for future research on methodologies employed but also it is anticipated the benefit to environment which can increased residents’ well-being in the vicinity of quarry sites.

Compressive strength evolution of thermally-stressed Saint Maximin limestone.

NASA Astrophysics Data System (ADS)

Farquharson, J.; Griffiths, L.; Baud, P.; Wadsworth, F. B.; Heap, M. J.

2017-12-01

The Saint Maximin quarry (Oise, France) opened in the early 1600s, and its limestone has been used extensively as masonry stone, particularly during the classical era of Parisian architecture from the 17th century onwards. Its widespread use has been due to a combination of its regional availability, its high workability, and its aesthetic appeal. Notable buildings completed using this material include sections of the Place de la Concorde and the Louvre in Paris. More recently, however, it has seen increasing use in the construction of large private residences throughout the United States as well as extensions to private institutions such as Stanford University. For any large building, fire hazard can be a substantial concern, especially in tectonically active areas where catastrophic fires may arise following large-magnitude earthquakes. Typically, house fires burn at temperatures of around 600 °C ( 1000 F). Given the ubiquity of this geomaterial as a building stone, it is important to ascertain the influence of heating on the strength of Saint Maximin limestone (SML), and in turn the structural stability of the buildings it is used in. We performed a series of compressive tests and permeability measurements on samples of SML to determine its strength evolution in response to heating to incrementally higher temperatures. We observe that the uniaxial compressive strength of SML decreases from >12 MPa at room temperature to <7 MPa at 600 °C. The rate of strength reduction increases at elevated temperature (>400 °C). We anticipate that this substantial weakening is in part a result of thermal microcracking, whereby changes in temperature induce thermal stresses due to a mismatch in thermal expansion between the constituent grains. This mechanism is compounded by the volumetric increase of quartz through its alpha - beta transition at 573 °C, and by the thermal decomposition of calcite. To track the formation of thermal microcracks, we monitor acoustic emissions

INTERIOR VIEW, NORTH QUARRY, LOOKING WEST. IN THE FOREGROUND ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, NORTH QUARRY, LOOKING WEST. IN THE FOREGROUND ON THE FIRST BENCH, POWDER HILLS ARE PRIMED FOR DOLOMITE EXTRACTION. ON THE SECOND BENCH, THE DRILL TEAM IS LAYING OUT THE NEXT SHOTS. - Wade Sand & Gravel Company, North Quarry, State Highway 78, Thomas, Jefferson County, AL

Geological-Technical and Geo-engineering Aspects of Dimensional Stone Underground Quarrying

NASA Astrophysics Data System (ADS)

Fornaro, Mauro; Lovera, Enrico

Underground exploitation of dimensional stones is not a novelty, being long since practised, as proved by a number of historical documents and by a certain number of ancient quarrying voids throughout the world. Anyway, so far, open cast quarrying has been the most adopted practice for the excavation of dimensional stones. One primary reason that led to this situation is of course connected to the lower production costs of an open cast exploitation compared to an underground one. This cheapness has been supported by geological and technical motives: on the one hand, the relative availability of surface deposits and, on the other, the development of technologies, which often can be used only outdoor. But, nowadays, general costs of quarrying activities should be re-evaluated because new, and often proper, restrictions have been strongly rising during recent years. As a consequence of both environmental and technical restrictions, pressure will more and more arise to reduce open cast quarrying and to promote underground exploitations. The trend is already well marked for weak rocks - for instance in the extractive basin of Carrara, where about one hundred quarries are active, 30 per cent is working underground, but also in Spain, Portugal and Greece the number of underground marble quarries is increasing - but not yet for hard rock quarrying, where only few quarries are working underground all around the world. One reason has to be found in cutting technologies traditionally used. In weak rocks, diamond wire saw and chain cutter are usable, with few adaptations, in underground spaces, while drilling and blasting, the traditional exploitation method for hard stone, is not easily usable in a confined space, where often only one free face is available. Many technicians and researchers agree that two technologies will probably open the door to underground quarrying in hard rocks: diamond wire and water jet. The first one is already available; the second should still be

Sedimentology, stratigraphy, and depositional environment of the Crystal Geyser Dinosaur Quarry, east-central Utah

USGS Publications Warehouse

Suarez, M.B.; Suarez, C.A.; Kirkland, J.I.; Gonzalez, Luis A.; Grandstaff, D.E.; Terry, D.O.

2007-01-01

The Crystal Geyser Dinosaur Quarry, near Green River, Utah, is located at the base of the Lower Cretaceous (Barremian) Yellow Cat Member of the Cedar Mountain Formation. The quarry preserves a nearly monospecific accumulation of a new basal therizinosauroid, Falcarius utahensis. We used field descriptions and petrographic analysis to determine the depositional environment and development of the quarry strata. Results of these analyses suggest that the quarry represents multiple episodes of bone accumulation buried by spring and overbank flood deposits. Evidence for these previously undescribed spring deposits includes calcite macroscopic structures within the quarry strata - such as pisolites and travertine fragments - and calcite micromorphologies - including radial-fibrous, feather, and scandulitic dendrite morphologies and tufa clasts. At least two episodes of bone incorporation are preserved in the quarry based on their stratigraphic position and lithologic associations. The unique depositional setting in and around the Crystal Geyser Dinosaur Quarry appears to have been favorable for the preservation of vertebrate fossils and provides insight into early Cretaceous environments in North America. Copyright ?? 2007, SEPM (Society for Sedimentary Geology).

Stationary and transient thermal states of barometric pumping in the access pit of an underground quarry.

PubMed

Perrier, Frédéric; Le Mouël, Jean-Louis

2016-04-15

The transition zone between free and underground atmospheres hosts spectacular phenomena, as demonstrated by temperature measurements performed in the 4.6m diameter and 20m deep vertical access pit of an abandoned underground quarry located in Vincennes, near Paris. In summer, a stable stratification of the atmosphere is maintained, with coherent temperature variations associated with atmospheric pressure changes, with a barometric tide S2 larger than 0.1°C peak to peak. When the winter regime of turbulent cold air avalanches is initiated, stratification with pressure induced signals can be restored transiently in the upper part of the pit, while the lower part remains fully mixed and insensitive to pressure variations. The amplitude of the pressure to temperature transfer function increases with frequency below 5×10(-4)Hz, with values at 3×10(-5)Hz varying from 0.1°C·hPa(-1) at the bottom up to 2°C·hPa(-1) towards the top of the pit. These temperature variations are accounted for by cave breathing, which is pressure induced motion of air amplified by the large volume of the quarry. This understanding is supported by a numerical model including advective heat transport, heat diffusion, and heat exchange with the pit walls. Mean lifetime in the pit is of the order of 9 to 13h, and barometric pumping results in an effective ventilation rate of the quarry of the order of 10(-7)s(-1). This study illustrates the important role of barometric pumping in heat and matter transport between atmosphere and lithosphere. The resulting stationary and transient states, revealed in this pit, are probably a general feature of functioning interface systems, and therefore are an important aspect to consider in problems of contaminant transport, or the preservation of precious heritage such as rare ecosystems or painted caves. Copyright © 2016 Elsevier B.V. All rights reserved.

Field evidence for control of quarrying by rock bridges in jointed bedrock

NASA Astrophysics Data System (ADS)

Hooyer, T. S.; Cohen, D. O.; Iverson, N. R.

2011-12-01

Quarrying is generally thought to be the most important mechanism by which glaciers erode bedrock. In quarrying models it is assumed that slow, subcritical, growth of pre-existing cracks rate-limits the process and occurs where there are large stress differences in the bed, such as near rock bumps where ice separates from the bed to form water-filled cavities. Owing to the direction of principal stresses in rocks associated with sliding and resultant cavity formation, models predict that quarrying will occur along cracks oriented perpendicular to the ice flow direction or parallel to zones of ice-bed contact. Preglacial cracks in rocks will tend to propagate mainly downward, and in sedimentary or some metamorphic rocks will merge with bedding planes, thereby helping to isolate rock blocks for dislodgement. In contrast to these model assumptions, new measurements of quarried surface orientations in the deglaciated forefield of nine glaciers in Switzerland and Canada indicate a strong correlation between orientations of pre-existing joints and quarried bedrock surfaces, independent of ice flow direction or ice-water contact lines. The strong correlation persists across all rock types, and rocks devoid of major joints lack quarried surfaces. We propose a new conceptual model of quarrying that idealizes the bedrock as a series of blocks separated by discontinuous preglacial joints containing intact rock bridges. Bridges concentrate stress differences caused by normal and shear forces acting at the rock surface. Failure of bridges is caused by slow subcritical crack growth enhanced by water pressure fluctuations. To lend credibility to this new model, we show field evidence of failed rock bridges in quarried surfaces and of rib marks on plumose structures that we interpret as arrest fracture fronts due to transient subglacial water-pressure fluctuations.

Studies on radon/thoron and their decay products in granite quarries around Bangalore city, India

NASA Astrophysics Data System (ADS)

Ningappa, C.; Sannappa, J.; Chandrashekara, M. S.; Paramesh, L.

2009-08-01

The radon survey was performed in granite quarries around Bangalore rural district and Bangalore city as part of a lung cancer epidemiological study. Long duration measurements of indoor and outdoor radon, thoron and their progenies concentrations were made around granite quarries of Bangalore rural district by using Solid State Nuclear Track Detector (SSNTD, LR-115, Type-II Plastic track detector) during summer and winter period (2006-07). The increase of radioactivity in granite quarries and inhalation dose to workers and populations near the quarries have been summarized. The higher concentrations of radon and thoron in granite quarries suggest radiation health effects on workers and public around the quarries is higher than permissible levels. The results are presented and analyzed with reference to ICRP limits.

Deep Impact Spots Quarry

NASA Technical Reports Server (NTRS)

2005-01-01

Sixty-nine days before it gets up-close-and-personal with a comet, NASA's Deep Impact spacecraft successfully photographed its quarry, comet Tempel 1, at a distance of 39.7 million miles. The image, taken on April 25, 2005, is the first of many comet portraits Deep Impact will take leading up to its historic comet encounter on July 4.

Lung Function Impact from Working in the Pre-Revolution Libyan Quarry Industry

PubMed Central

Draid, Marwan M.; Ben-Elhaj, Khaled M.; Ali, Ashraf M.; Schmid, Kendra K.; Gibbs, Shawn G.

2015-01-01

The purpose of this study was to determine the lung impact from working within the Libyan quarry industry, and if the length of work impacted the degree of degradation. Eighty three workers from eight silica quarries in the Nafusa Mountains of Libya opted to participate. These quarries were working the upper cretaceous geological structure. Eighty-five individuals who lived in Gharyan City with no affiliation to quarry operations participated as controls. Spirometry variables evaluated were Forced Vital Capacity (FVC), Forced Expiratory Volume at 1.0 second (FEV1), FVC/FEV1 and Peak Expiratory Flow (PEF). Control and exposed groups had no differences in terms of height, weight, or smoking status (p = 0.18, 0.20, 0.98, respectively). Prior to adjustment for other variables, FVC, FEV1, and PEF are all significantly lower in the exposed group (p = 0.003, 0.009, 0.03, respectively). After adjustment for age, height, weight, and smoking status, there remain significant differences between the control and exposed groups for FVC, FEV1, and PEF. This analysis demonstrated that exposure to quarry dust has a detrimental effect on lung function, and that pre-revolution Libyan quarry workers were being exposed. This study shows that any exposure is harmful, as the reduction in lung function was not significantly associated with years of exposure. PMID:25961801

Lung function impact from working in the pre-revolution Libyan quarry industry.

PubMed

Draid, Marwan M; Ben-Elhaj, Khaled M; Ali, Ashraf M; Schmid, Kendra K; Gibbs, Shawn G

2015-05-07

The purpose of this study was to determine the lung impact from working within the Libyan quarry industry, and if the length of work impacted the degree of degradation. Eighty three workers from eight silica quarries in the Nafusa Mountains of Libya opted to participate. These quarries were working the upper cretaceous geological structure. Eighty-five individuals who lived in Gharyan City with no affiliation to quarry operations participated as controls. Spirometry variables evaluated were Forced Vital Capacity (FVC), Forced Expiratory Volume at 1.0 second (FEV1), FVC/FEV1 and Peak Expiratory Flow (PEF). Control and exposed groups had no differences in terms of height, weight, or smoking status (p = 0.18, 0.20, 0.98, respectively). Prior to adjustment for other variables, FVC, FEV1, and PEF are all significantly lower in the exposed group (p = 0.003, 0.009, 0.03, respectively). After adjustment for age, height, weight, and smoking status, there remain significant differences between the control and exposed groups for FVC, FEV1, and PEF. This analysis demonstrated that exposure to quarry dust has a detrimental effect on lung function, and that pre-revolution Libyan quarry workers were being exposed. This study shows that any exposure is harmful, as the reduction in lung function was not significantly associated with years of exposure.

[Investigation of noise hazards and hearing status of workers in outdoor quarries].

PubMed

Zhang, Guoying; Tang, Zhifeng; Yao, Yongping; Wang, Haiying

2014-08-01

To investigate the noise hazards in open quarries and to provide a basis for further control of noise hazards. An investigation was performed during 2010 to 2011 among all open quarries in Deqing County of Zhejiang Province, China. The investigation included basic information of the quarries, the occupational health situation and noise intensity at the workplace, and the hearing loss of workers exposed to noise in quarry enterprises. The hearing test results were evaluated based on the Diagnostic criteria of occupational noise-induced hearing loss (GBZ 49-2007). A total of 25 enterprises with open quarries were investigated, of which only 30.4% (17/56) workplaces met the national standard. The median noise level was 92.5 dB (A). Fifty-four (10.6%) out of 508 workers in the 25 enterprises were diagnosed with binaural hearing loss in the initial physical examination, with 18.3% (93/508) under surveillance. The rate of normal hearing among crushing workers, mechanists, drilling workers, and blasting workers ranged between 27.6% and 41.4%, which was significantly lower than that among workers exposed to slight noise hazards (80.0%) or other workers (63.7%) (P < 0.05). With increasing working years, the binaural hearing loss of crushing workers became serious. Serious occupational noise hazards existed in most jobs in open quarries, with crushing workers, mechanists, drilling workers, and blasting workers most seriously jeopardized. Among crushing workers, those working in the first-line or unprotected second?line positions suffered more than the others. Further measures should be taken by the supervision department and the enterprises to control the noise hazards in open quarries.

Two new Bent-toed Geckos of the Cyrtodactylus pulchellus complex from Peninsular Malaysia and multiple instances of convergent adaptation to limestone forest ecosystems.

PubMed

Grismer, L Lee; Wood, Perry L; Anuar, Shahrul; Grismer, Marta S; Quah, Evan S H; Murdoch, Matthew L; Muin, Mohd Abdul; Davis, Hayden R; Aguilar, César; Klabacka, Randy; Cobos, Anthony J; Aowphol, Anchalee; Sites, Jack W

2016-04-25

A new species of limestone cave-adapted gecko of the Cyrtodactylus pulchellus complex, C. hidupselamanya sp. nov., is described from an isolated karst formation at Felda Chiku 7, Kelantan, Peninsular Malaysia. This formation is scheduled to be completely quarried for its mineral content. From what we know about the life history of C. hidupselamanya sp. nov., this will result in its extinction. A new limestone forest-adapted species, C. lenggongensis sp. nov., from the Lenggong Valley, Perak was previously considered to be conspecific with C. bintangrendah but a re-evaluation of morphological, color pattern, molecular, and habitat preference indicates that it too is a unique lineage worthy of specific recognition. Fortunately C. lenggongensis sp. nov. is not facing extinction because its habitat is protected by the UNESCO Archaeological Heritage of the Lenggong Valley due to the archaeological significance of that region. Both new species can be distinguished from all other species of Cyrtodactylus based on molecular evidence from the mitochondrial gene ND2 and its flanking tRNAs as well as having unique combinations of morphological and color pattern characteristics. Using a time-calibrated BEAST analysis we inferred that the evolution of a limestone habitat preference and its apparently attendant morphological and color pattern adaptations evolved independently at least four times in the C. pulchellus complex between 26.1 and 0.78 mya.

Geohydrology of the Gallup's Quarry area, Plainfield, Connecticut

USGS Publications Warehouse

Melvin, Robert L.; Stone, Janet Radway; Craft, Patrick A.; Lane, John W.

1995-01-01

The geohydrology of the Gallup's Quarry area in Plainfield, Connecticut was characterized by the U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency, to provide a preliminary framework for future remedial efforts. Gallup's Quarry, an inactive sand and gravel pit, was the site of unregulated disposal of an unknown volume of chemical wastes from at least the summer of 1977 until January 1978. Existing information collected for the Connecticut Department of Environmental Protection during 1978-82 showed that ground water beneath Gallup's Quarry and adjacent land to the northwest was contaminated by organic and inorganic compounds. There is also some evidence for contamination of Mill Brook, which is located north and northwest of the disposal areas. Geologic mapping and subsurface data show that unconsolidated surficial materials up to 90 feet thick overlie fractured crystalline bedrock in most of the Gallup's Quarry area. The surficial materials consist primarily of stratified drift and till. Texture changes vertically and laterally within the stratified drift; grain size ranges from very coarse to fine. Till blankets the bedrock surface beneath the stratified drift and is a few feet to as much as 25 feet thick. Bedrock is exposed at land surface in a hill in the southeastern part of the quarry and slopes to depths of up to 90 feet beneath the area west and north of the disposal sites. The bedrock is a dark, fine-grained, fractured and jointed blastomylonite and hornblende gneiss of the Quinebaug Formation. It is likely that a west- northwest-trending fault is present in the bedrock beneath Gallup's Quarry; this fault, if present, may provide a preferential pathway for ground-water flow and contaminant transport. The principal horizontal direction of ground-water flow and movement of dissolved contaminants in the stratified drift was to the northwest of the waste-disposal areas toward Mill Brook in 1978. Estimates of average annual

Respiratory symptoms and ventilatory functions among quarry workers in Edo state, Nigeria

PubMed Central

Isara, Alphonsus Rukevwe; Adam, Vincent Yakubu; Aigbokhaode, Adesuwa Queen; Alenoghena, Innocent Osi

2016-01-01

Introduction Workers in the quarry industries are exposed to hazards resulting from the inhalation of air borne particulates. The study determined the prevalence of respiratory symptoms and assessed ventilatory functions among quarry workers in Edo state, Nigeria. Methods Quarry workers (site workers and office workers) were interviewed using structured questionnaire. FEV1, FVC, FEV1/FVC and PEFR were measured using a KoKo Legend spirometer. Results A total of 113 quarry workers (76 exposure and 37 controls) were studied. The exposure group had significantly higher occurrence of chest tightness (35.5%) compared with 16.2% of the controls (p < 0.05). The occurrence of cough (23.7% versus 13.5%), sputum (21.1% versus 16.2%), and dyspnoea (7.9% versus 5.4%), were higher in exposure groups while wheeze (10.8% versus 10.5%) and nasal congestion (27.0% and 25.0%) were higher in the control groups. The mean (SD) FEV1, and FVC were significantly lower among the exposure compared with the control group; 2.77L (0.73) versus 3.14L (0.78), p < 0.05, and 3.48L (0.84) versus 3.89L (0.92), p < 0.05. In both groups, smokers had significantly lower mean (SD) FEV1, FVC and PEFR compared with non-smokers; 2.91L (0.77) versus 3.39L (0.69), p = 0.01, 3.61L (0.91) versus 4.26L (0.74), p < 0.05 and 6.56L (2.43) versus 7.98L (1.67), p < 0.05. Conclusion Chronic exposure to quarry dust is associated with respiratory symptoms and reduced lung function indices among quarry workers. The enforcement of the use of PPEs and periodic evaluation the lung function status of quarry workers is advocated. PMID:27347301

Respiratory symptoms and ventilatory functions among quarry workers in Edo state, Nigeria.

PubMed

Isara, Alphonsus Rukevwe; Adam, Vincent Yakubu; Aigbokhaode, Adesuwa Queen; Alenoghena, Innocent Osi

2016-01-01

Workers in the quarry industries are exposed to hazards resulting from the inhalation of air borne particulates. The study determined the prevalence of respiratory symptoms and assessed ventilatory functions among quarry workers in Edo state, Nigeria. Quarry workers (site workers and office workers) were interviewed using structured questionnaire. FEV1, FVC, FEV1/FVC and PEFR were measured using a KoKo Legend spirometer. A total of 113 quarry workers (76 exposure and 37 controls) were studied. The exposure group had significantly higher occurrence of chest tightness (35.5%) compared with 16.2% of the controls (p < 0.05). The occurrence of cough (23.7% versus 13.5%), sputum (21.1% versus 16.2%), and dyspnoea (7.9% versus 5.4%), were higher in exposure groups while wheeze (10.8% versus 10.5%) and nasal congestion (27.0% and 25.0%) were higher in the control groups. The mean (SD) FEV1, and FVC were significantly lower among the exposure compared with the control group; 2.77L (0.73) versus 3.14L (0.78), p < 0.05, and 3.48L (0.84) versus 3.89L (0.92), p < 0.05. In both groups, smokers had significantly lower mean (SD) FEV1, FVC and PEFR compared with non-smokers; 2.91L (0.77) versus 3.39L (0.69), p = 0.01, 3.61L (0.91) versus 4.26L (0.74), p < 0.05 and 6.56L (2.43) versus 7.98L (1.67), p < 0.05. Chronic exposure to quarry dust is associated with respiratory symptoms and reduced lung function indices among quarry workers. The enforcement of the use of PPEs and periodic evaluation the lung function status of quarry workers is advocated.

7 CFR 330.301 - Stone and quarry products from certain areas in Canada.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE FEDERAL PLANT PEST REGULATIONS; GENERAL; PLANT PESTS; SOIL, STONE, AND QUARRY PRODUCTS; GARBAGE Movement of Soil, Stone, And Quarry Products...

Lithotype characterizations by Nuclear Magnetic Resonance (NMR): A case study on limestone and associated rocks from the eastern Dahomey Basin, Nigeria

NASA Astrophysics Data System (ADS)

Olatinsu, O. B.; Olorode, D. O.; Clennell, B.; Esteban, L.; Josh, M.

2017-05-01

Three representative rock types (limestone, sandstone, and shale) and glauconite samples collected from Ewekoro Quarry, eastern Dahomey Basin in Nigeria were characterized using low field 2 MHz and 20 MHz Nuclear Magnetic Resonance (NMR) techniques. NMR T2 relaxation time decay measurement was conducted on disc samples under partial water-saturation and full water-saturation conditions using CPMG spin-echo routine. The T2 relaxation decay was converted into T2 distribution in the time domain to assess and evaluate the pore size distribution of the samples. Good agreement exists between water content from T2 NMR distributions and water imbibition porosity (WIP) technique. Results show that the most useful characteristics to discriminate the different facies come from full saturation NMR 2 MHz pore size distribution (PSD). Shale facies depict a quasi-unimodal distribution with greater than 90% contribution from clay bound water component (T2s) coupled to capillary bound water component (T2i) centred on 2 ms. The other facies with well connected pore structure show either bimodal or trimodal T2 distribution composed of the similar clay bound water component centred on 0.3 ms and quasi-capillary bound water component centred on 10 ms. But their difference depends on the movable water T2 component (T2l) that does not exist in the glauconite facies (bimodal distribution) while it exists in both the sandstone and limestone facies. The basic difference between the limestone and sandstone facies is related to the longer T2 coupling: T2i and T2l populations are coupled in sandstone generating a single population which convolves both populations (bimodal distribution). Limestone with a trimodal distribution attests to the fact that carbonate rocks have more complex pore system than siliclastic rocks. The degree of pore connectivity is highest in sandstone, followed by limestone and least in glauconite. Therefore a basic/quick NMR log run on samples along a geological

INTERIOR VIEW, NORTH QUARRY, LOOKING WEST. IN THE FOREGROUND ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, NORTH QUARRY, LOOKING WEST. IN THE FOREGROUND ON THE FIRST BENCH, POWDER HILLS ARE PRIMED FOR DOLOMITE EXTRACTION. ON THE SECOND BENCH, THE DRILL TEAM IS LAYING OUT THE NEXT SHOTS. ON THE TOP BENCH, A 245 CATERPILLAR LOADER FILLS A 55-TON CATERPILLAR ROCK TRUCK WITH EXTRACTED DOLOMITE FOR TRANSPORT TO THE DOLOMITE CRUSHING AND SCREENING PLANT. - Wade Sand & Gravel Company, North Quarry, State Highway 78, Thomas, Jefferson County, AL

Paleozoic Hydrocarbon-Seep Limestones

NASA Astrophysics Data System (ADS)

Peckmann, J.

2007-12-01

To date, five Paleozoic hydrocarbon-seep limestones have been recognized based on carbonate fabrics, associated fauna, and stable carbon isotopes. These are the Middle Devonian Hollard Mound from the Antiatlas of Morocco [1], Late Devonian limestone lenses with the dimerelloid brachiopod Dzieduszyckia from the Western Meseta of Morocco [2], Middle Mississippian limestones with the dimerelloid brachiopod Ibergirhynchia from the Harz Mountains of Germany [3], Early Pennsylvanian limestones from the Tantes Mound in the High Pyrenees of France [4], and Late Pennsylvanian limestone lenses from the Ganigobis Shale Member of southern Namibia [5]. Among these examples, the composition of seepage fluids varied substantially as inferred from delta C-13 values of early diagenetic carbonate phases. Delta C-13 values as low as -50 per mil from the Tantes Mound and -51 per mil from the Ganigobis limestones reveal seepage of biogenic methane, whereas values of -12 per mil from limestones with Dzieduszyckia associated with abundant pyrobitumen agree with oil seepage. Intermediate delta C-13 values of carbonate cements from the Hollard Mound and Ibergirhynchia deposits probably reflect seepage of thermogenic methane. It is presently very difficult to assess the faunal evolution at seeps in the Paleozoic based on the limited number of examples. Two of the known seeps were typified by extremely abundant rhynchonellide brachiopods of the superfamily Dimerelloidea. Bivalve mollusks and tubeworms were abundant at two of the known Paleozoic seep sites; one was dominated by bivalve mollusks (Hollard Mound, Middle Devonian), another was dominated by tubeworms (Ganigobis Shale Member, Late Pennsylvanian). The tubeworms from these two deposits are interpreted to represent vestimentiferan worms, based on studies of the taphonomy of modern vestimentiferans. However, this interpretation is in conflict with the estimated evolutionary age of vestimentiferans based on molecular clock methods

Geomorphological records of diachronous quarrying activities along the ancient Appia route at the Aurunci Mountain pass (Central Italy)

NASA Astrophysics Data System (ADS)

Di Luzio, E.; Carfora, P.

2018-04-01

The topic of this research consists in the description of landscape modifications occurring from the 4th century BCE to the 19th century CE as a consequence of quarrying activities on carbonate slopes along a tract of the ancient Appia route crossing the central Apennine belt at the Aurunci Mountain pass (Lazio region, central Italy). The main objectives were to discern different quarrying phases and techniques, quantify quarrying activities and understand the role of quarrying in create morphological features. Multidisciplinary studies were completed including aerial photogrammetry, geoarchaeological field surveys, morphometric characterization of quarry areas, structural analysis of rock outcrops aided by terrestrial photogrammetry, GPS measurements. The results of this study show how the local geomorpological and tectonic setting determined which kinds of extractable rock material, i.e., rock blocks or breccias, were used for different purposes. Moreover, different phases of extraction were evidenced. A main Roman quarrying phase, lasting between the 4th century BCE and the 1st century CE, was recognized as taking place over eight quarry areas. These are delimited by sharp edges and have regular shapes, revealing in some cases a staircase-like morphological profile, and are characterized by similar volumes of extracted rock material. A later quarrying phase -the Bourbon Age, 19th century CE-is assumed to be evidenced instead by five quarries with a peculiar semi-elliptical shape and different volumes of carved material. Seven quarries were found to be of uncertain age. The quarry system described in this paper, together with geomorphological records of slope cuts, terraced surfaces, and the remains of retaining walls, represents a unique and important example of anthropogenic landscape modification in the territory of the central Apennines caused by the construction and maintenance of a Roman road over the centuries. This could be relevant for further studies on

Land abandonment, fire recurrence and soil carbon content in the Macizo del Caroig, Eastern Spain

NASA Astrophysics Data System (ADS)

Cerdá, A.; González Peñaloza, F.; Santín, C.; Doerr, S. H.

2012-04-01

During the last 50 years two main forces have driven the fate of Mediterranean landscapes: land abandonment and forest fires (MacDonald et al., 2000; Moreira et al., 2001). Due to the economical changes suffered by the of the Mediterranean countries after the Second World War, the population migrated from the rural to the urban areas, and from South to North Europe. The land abandonment allowed the vegetation to recover and, as a consequence, an increase in forest fire took place. The soils of the abandoned land recovered the vegetation and litter layers, and consequently changes in soil properties have being found. One of these changes is the increase of soil carbon content, which is due both to vegetation recovery and to fire occurrence that increases the ash and pyrogenic carbon content in soils. Twenty plots were selected in the Macizo del Caroig in Eastern Spain on soils developed on limestone. The period of abandonment and the forest fires that had affected each plot were determined by interviews with the owners, farmers and shepherds. In addition, six (three + three) plots were selected as forest (no plough) and cultivated control plots. Each plot was sampled (10 random samples) and the organic carbon content determined. The results show that the cultivated plots have organic matter contents of 1.02 %, and the forest (Quercus ilex sp.) plots reach the highest value: 14.98 %. Within those we found values that range from 2.34 %, in the recently abandoned plots (10 year abandonment), to values of 8.23 % in the 50 year old abandoned fields.The results demonstrate that there is a recovery of the organic carbon in abandoned soils and that the forest fires do no affect this trend. The increase of soil organic matter after abandonment is a result of the recovery of vegetation(Debussche et al., 2001), which is the consequence of the end of the disturbance of forest that have affected the Mediterranean for millennia (Barbero et al., 1990). The colonization of the

The influence of petrography, mineralogy and chemistry on burnability and reactivity of quicklime produced in Twin Shaft Regenerative (TSR) kilns from Neoarchean limestone (Transvaal Supergroup, South Africa)

NASA Astrophysics Data System (ADS)

Vola, Gabriele; Sarandrea, Luca; Della Porta, Giovanna; Cavallo, Alessandro; Jadoul, Flavio; Cruciani, Giuseppe

2017-12-01

This study evaluates the influence of chemical, mineralogical and petrographic features of the Neoarchean limestone from the Ouplaas Mine (Griqualand West, South Africa) on its burnability and quicklime reactivity, considering the main use as raw material for high-grade lime production in twin shaft regenerative (TSR) kilns. This limestone consists of laminated clotted peloidal micrite and fenestrate microbial boundstone with herringbone calcite and organic carbon (kerogen) within stylolites. Diagenetic modifications include hypidiotopic dolomite, micrite to microsparite recrystallization, stylolites, poikilotopic calcite, chert and saddle dolomite replacements. Burning and technical tests widely attest that the Neoarchean limestone is sensitive to high temperature, showing an unusual and drastically pronounced sintering or overburning tendency. The slaking reactivity, according to EN 459-2 is high for lime burnt at 1050 °C, but rapidly decreases for lime burnt at 1150 °C. The predominant micritic microbial textures, coupled with the organic carbon, are key-factors influencing the low burnability and the high sintering tendency. The presence of burial cementation, especially poikilotopic calcite, seems to promote higher burnability, either in terms of starting calcination temperature, or in terms of higher carbonate dissociation rate. In fact, the highest calcination velocity determined by thermal analysis is consistent with the highest slaking reactivity of the lower stratum of the quarry, enriched in poikilotopic calcite. Secondly, locally concentered dolomitic marly limestones, and sporadic back shales negatively affects the quicklime reactivity, as well. This study confirms that a multidisciplinary analytical approach is essential for selecting the best raw mix for achieving the highest lime reactivity in TSR kilns.

21 CFR 184.1409 - Ground limestone.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Ground limestone. 184.1409 Section 184.1409 Food... Specific Substances Affirmed as GRAS § 184.1409 Ground limestone. (a) Ground limestone consists essentially (not less than 94 percent) of calcium carbonate (CaCO3) and is prepared by the crushing, grinding, and...

21 CFR 184.1409 - Ground limestone.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ground limestone. 184.1409 Section 184.1409 Food... Specific Substances Affirmed as GRAS § 184.1409 Ground limestone. (a) Ground limestone consists essentially (not less than 94 percent) of calcium carbonate (CaCO3) and is prepared by the crushing, grinding, and...

Compilation and preliminary interpretation of hydrologic data for the Weldon Spring radioactive waste-disposal sites, St Charles County, Missouri; a progress report

USGS Publications Warehouse

Kleeschulte, M.J.; Emmett, L.F.

1986-01-01

The Weldon Spring Chemical Plant is located just north of the drainage divide separating the Mississippi River and the Missouri River in St. Charles County, Missouri. From 1957 to 1966 the plant converted uranium-ore concentrates and recycled scrap to pure uranium trioxide, uranium tetrafluoride, and uranium metal. Residues from these operations were pumped to four large pits that had been excavated near the plant. Small springs and losing streams are present in the area. Water overlying the residue in the pits has a large concentration of dissolved solids and a different chemical composition compared to the native groundwater and surface water. This difference is indicated by the concentrations of calcium, sodium, sulfate, nitrate, fluoride, uranium, radium, lithium, molybdenum, strontium, and vanadium, all of which are greater than natural or background concentrations. Water from Burgermeister Spring, located about 1.5 miles north of the chemical plant area, contains uranium and nitrate concentrations greater than background concentrations. Groundwater in the shallow bedrock aquifer moves northward from the vicinity of the chemical plant toward Dardenne Creek. An abandoned limestone quarry several miles southwest of the chemical plant also has been used for the disposal of radioactive waste and rubble. Groundwater flow from the quarry area is southward through the alluvium, away from the quarry and toward the Missouri River. The St. Charles County well field is located in the Missouri River flood plain near the quarry and the large yield wells are open to the Missouri River alluvial aquifer. Water from a well 4,000 ft southeast of the quarry was analyzed; there was no indication of contamination from the quarry. Additional water quality and water level data are needed to determine if water from the quarry moves toward the well field. Observation wells need to be installed in the area between the chemical plant, pits, and Dardenne Creek. The wells would be used to

Report of investigation on underground limestone mines in the Ohio region. [Jonathan Mine, Alpha Portland Cement Mine, and Lewisburg Mine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Byerly, D.W.

1976-06-01

The following is a report of investigation on the geologic setting of several underground limestone mines in Ohio other than the PPG mine at Barberton, Ohio. Due to the element of available time, the writer is only able to deliver a brief synopsis of the geology of three sites visited. These three sites and the Barberton, Ohio site are the only underground limestone mines in Ohio to the best of the writer's knowledge. The sites visited include: (1) the Jonathan Mine located near Zanesville, Ohio, and currently operated by the Columbia Cement Corporation; (2) the abandoned Alpha Portland Cement Minemore » located near Ironton, Ohio; and (3) the Lewisburg Mine located at Lewisburg, Ohio, and currently being utilized as an underground storage facility. Other remaining possibilities where limestone is being mined underground are located in middle Ordovician strata near Carntown and Maysville, Kentucky. These are drift mines into a thick sequence of carbonates. The writer predicts, however, that these mines would have some problems with water due to the preponderance of carbonate rocks and the proximity of the mines to the Ohio River. None of the sites visited nor the sites in Kentucky have conditions comparable to the deep mine at Barberton, Ohio.« less

Strontium and carbon isotope stratigraphy of the Late Jurassic shallow marine limestone in western Palaeo-Pacific, northwest Borneo

NASA Astrophysics Data System (ADS)

Kakizaki, Yoshihiro; Weissert, Helmut; Hasegawa, Takashi; Ishikawa, Tsuyoshi; Matsuoka, Jun; Kano, Akihiro

2013-09-01

Strontium and carbon isotope stratigraphy was applied to a 202 m-thick shallow marine carbonate section within the Late Jurassic Bau Limestone at the SSF quarry in northwest Borneo, Malaysia, which was deposited in the western Palaeo-Pacific. Strontium isotopic ratios of rudist specimens suggest that the SSF section was formed between the latest Oxfordian (155.95 Ma) and the Late Kimmeridgian (152.70 Ma), which is consistent with previous biostratigraphy. The δ13Ccarb values of bulk carbonate range from -0.10 to +2.28‰ and generally show an increasing upward trend in the lower part of the section and a decreasing upward trend in the upper part of the section. A comparable pattern is preserved in the δ13Corg isotope record. Limestone samples of the SSF section mainly preserve the initial δ13Ccarb values, except for the interval 84-92 m, where an apparent negative anomaly likely developed as a result of meteoric diagenesis. Comparing with the Tethyan δ13Ccarb profile, a negative anomaly in the lower SSF section can be correlated with the lowered δ13C values around the Oxfordian/Kimmeridgian boundary. In addition, δ13Ccarb values of the Bau Limestone are generally ∼1‰ lower than the Tethyan values, but comparable with the values reported from Scotland and Russia, located in Boreal realm during the Late Jurassic. This suggests that either the Tethyan record or the other records have been affected by the δ13C values of regionally variable dissolved inorganic carbon (DIC). The Late Jurassic δ13CDIC values are thought to have been regionally variable as a result of their palaeoceanographic settings. This study shows that δ13C chemostratigraphy of the Palaeo-Pacific region contributes to an improved understanding of global carbon cycling and oceanography during this time period.

Using a noise monitoring station in a small quarry located in an urban area.

PubMed

Wichers, Michiel; Iramina, Wilson Siguemasa; de Eston, Sérgio Médici; Ayres da Silva, Anna Luiza Marques

2017-12-22

Mining plays an important role in Brazilian exports. On the other hand, large urban centers like São Paulo, with approximately 21 million inhabitants, also demand an increasing domestic consumption of natural resources, such as construction aggregate. There are many quarries located in the surroundings of urban centers in Brazil, competing with the growth of urbanized areas. Such proximity leads to a series of conflicts involving quarries and surrounding communities, where the increase in noise levels is highlighted. Operations in quarries, in general, are intermittent. Noisier equipment, such as drilling rigs and primary crushers, operates only a few hours during the day, while other operations, such as screening and secondary and tertiary crushing, are more constant. This paper presents a study carried out in a quarry located near São Paulo, where in addition to conventional short term noise measurements at surrounding receptors, one noise monitoring station was installed, allowing to identify the noisiest moments during the quarry operating time. Through data transmitted by wireless technology, it was possible to follow the noise variations emitted from mining activities in real time and observe the noisiest events that were recorded for events that exceeded the established standards. A mobile application associated to this monitoring station facilitated the quarry's manager and employees to access immediately the monitoring information. Therefore, by using this system, it was possible to evaluate the effectiveness of noise reduction measures already taken and indicate what steps still need to be held.

CALCIUM CARBONATE DISSOLUTION RATE IN LIMESTONE CONTACTORS

EPA Science Inventory

The rate of carbonate mineral dissolution from limestone was studied using a rotating disk apparatus and samples of limestone of varied composition. The purpose of this study was to determine the effect of limestone composition on the kinetics of carbonate mineral dissolution. Th...

Physical and mechanical properties of quarry dust waste incorporated into fired clay brick

NASA Astrophysics Data System (ADS)

Kadir, A. A.; Hassan, M. I. H.; Sarani, N. A.; Rahim, A. S. Abdul; Ismail, N.

2017-04-01

A large amount of quarry dust waste is dispose into landfills every year. This waste was obtained as a by-product during the production of aggregates through the crushing process of rocks in rubble crusher units. The increasing value of waste will have significant impact towards health and environment. Recycling such wastes by incorporating them into building materials is a practical solution for pollution problem. Therefore, this research was to examine the possibility of quarry dust to be incorporated in fired clay bricks. In this research, the composition and concentration of heavy metals were determined by using X-Ray Fluorescence Spectrometer (XRF). The research also consists of physical and mechanical properties of the fired clay bricks by utilizing quarry dust waste. Brick was manufactured by incorporating different percentages of quarry dust waste which are 0%, 10%, 20% and 30%. All bricks sample was tested with physical and mechanical properties which were density, shrinkage, initial rate of suction (IRS) and compressive strength of the fired bricks. Furthermore, the density and shrinkage were also in standard range. All physical and mechanical results were complied with the BS 3921:1985 standard. The comprehensive experimental work described in this research investigated the possibility of incorporating quarry dust into fired clay bricks. These materials could be an alternative low cost material for brick and at the same time provide a new disposal method for the waste.

Handling of quarry waste from schist production at Oppdal, Norway

NASA Astrophysics Data System (ADS)

Willy Danielsen, Svein; Alnæs, Lisbeth; Azrague, Kamal; Suleng, Jon

2017-04-01

Handling of quarry waste from schist production at Oppdal, Norway Svein Willy Danielsen1), Lisbeth Alnæs2), Kamal Azrague2), Jon Suleng3) 1) Geomaterials Consultant, Trondheim Norway, 2) SINTEF, Trondheim, Norway, 3) AF Gruppen AS, Oppdal, Norway A significant amount of aggregate research in Norway has been focused on the recovery and use of surplus sizes from hard rock aggregate quarries. The use of sand sized quarry waste (QW) from crushing/processing has been motivated by the rapid depletion of traditional sand/gravel resources, increasing land-use conflicts, and the need to minimise QW deposits which for some quarries are becoming a critical factor for economy as well as for environmental reasons. With an annual aggregate production of 77 million tons, out of which approximately 83 % comes from hard rock, the annual volume of size < 4 mm will be of the order of 19 million tons. Converting this into construction aggregates is a major challenge in order to obtain satisfactory mass balance. This challenge is even bigger for quarries producing decorative stones. E.g. the quarrying and production of schist products for building purpose normally utilises as little as 10-15 % of the excavated rock. Oppdal in central Norway is a main supplier of schist products for flooring, roofing and decorative purpose. The high percentage of QW is due to strict requirements to the finished products, both regarding processing and the character of the parent rock. The need to deposit large amounts of QW is a serious setback for the quarry economy. Within a limited time horizon the volumes of QW can threaten the further exploitation by merely choking the quarry. On the opposite side - any process that can convert the QW into sellable products will give a tremendous added value for the producer. Besides, the area in question is about to drain out its available aggregate resources, having to rely on long-transported sand and gravel. This has consequences not only for the economy, but

Comparison of physical and mechanical properties of river sand concrete with quarry dust concrete

NASA Astrophysics Data System (ADS)

Opara, Hyginus E.; Eziefula, Uchechi G.; Eziefula, Bennett I.

2018-03-01

This study compared the physical and mechanical properties of river sand concrete with quarry dust concrete. The constituent materials were batched by weight. The water-cement ratio and mix ratio selected for the experimental investigation were 0.55 and 1:2:4, respectively. The specimens were cured for 7, 14, 21 and 28 days. Slump, density and compressive strength tests were carried out. The results showed that river sand concrete had greater density and compressive strength than quarry dust concrete for all curing ages. At 28 days of curing, river sand concrete exceeded the target compressive strength by 36%, whereas quarry dust concrete was less than the target compressive strength by 12%. Both river sand concrete and quarry dust concrete for the selected water/cement ratio and mix ratio are suitable for non-structural applications and lightly-loaded members where high strength is not a prerequisite.

Effects of limestone on starch digestion in Holstein steers.

PubMed

Tissera, G H; Vandersall, J H; Erdman, R A

1988-03-01

Eight calcitic and three dolomitic limestones were examined for particle size and reactivity with hydrochloric acid at pH 3.5 and 5.5. Reactivity was higher in calcitic than dolomitic limestone. Within calcitic limestones, reactivity was highly related to particle size. A highly reactive limestone was selected for use in two digestion trials with Holstein steers. In Trial 1, 4 steers (approximately 300 kg) were fed diets consisting of 40% corn silage and 60% concentrate (DM basis) with .62 or 2.34% limestone in a single reversal trial with 3-wk experimental periods. Added limestone affected only starch digestibility, which increased from 91.3 to 93.2%. Fecal pH increased from 5.7 to 6.4 by limestone addition. In trial 2, four rumen and duodenally cannulated steers (approximately 475 kg) were fed the same diets in the same design. Limestone addition increased fecal pH from 5.7 to 6.5. There were no effects of limestone on rumen or total tract digestion of starch or other nutrients. Limestone addition had no effect on rumen pH, buffering capacity, or VFA concentrations. Addition of a highly reactive limestone to diets containing high amounts of starch had little effect on starch digestion in either the rumen or lower gastrointestinal tract.

Faunas of Mississippian oolitic limestones: Evidence from Salem Limestone, southern Indiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feldman, H.R.

In the Salem Limestone of southern Indiana, a correlation exists between the faunal assemblage and abundance of grains with superficial oolitic coatings in grainstones. Coarse, poorly sorted fossiliferous grainstones are dominated by an echinoderm-bryozoan-brachiopod assemblage of fossils with few mollusks. The presence of large whole fossils, such as articulated crinoid calyces, suggest limited transport of skeletal components. Grainstones, dominated by grains with superficial coatings, and foraminifers tend to contain a diverse mollusk-dominated assemblage of gastropods, bivalves, rostroconchs, chitins, and scaphopods. These fossils are disarticulated, but generally are not fragmented even though many of them are thin and delicate. Echinoderms, brachiopods,more » and bryozoans are repsented in the mollusk-domdinated assemblage almost exclusively by well-rounded and coated fragments, suggesting that they are not in situ. The presence of similar molluscan assemblages in other Mississippian coated-grain grainstones from Alabama (the Monteagle Limestone) and Oklahoma (an unnamed limestone) indicates that the assemblage may have been wide-spread. Mississippian grainstones dominated by oolites (which are not prominent in the Salem) generally have very few fossils.« less

Comparison of the occupational safety applications in marble quarries of Carrara (Italy) and Iscehisar (Turkey) by using Elmeri method.

PubMed

Ersoy, Metin; Yesilkaya, Liyaddin

2016-01-01

In this paper, a brief summary is given about marble quarries in Carrara (Italy) and Iscehisar (Turkey), the Elmeri method is introduced, work accidents that can happen in marble quarries and their causes besides work safety behaviours in fields are explained, and the Elmeri monitoring method is applied and analysed. For this reason, marble quarries are divided into seven in terms of working conditions and active six quarries both in Carrara and Iscehisar areas, and work safety behaviours are analysed. Analysis process is based on True-False method; there are 18 items in total under six main topics; three items on each topic. The safety index for each section and the main topics are also calculated. According to the calculated safety indexes, Carrara area marble quarries (65.08%) are safer than Iscehisar area marble quarries (46.01%).

THERMAL TECHNOLOGY TESTED FOR CONTAMINANT RECOVERY

EPA Science Inventory

A research project on steam enhanced remediation (SER) for the recovery of dense nonaqueous phase liquid (DNAPL) from fractured limestone has been undertaken at the former Loring Air Force Base Quarry site in Limestone, ME. Participants in the project include the Maine Departmen...

Limestone Caverns

ERIC Educational Resources Information Center

Powell, Richard L.

1970-01-01

Describes the origin of limestone caverns, using Mammoth Cave as an example, with particular reference to the importance of groundwater information of caverns, the present condition of groundwater, and how caverns develop within fluctuating groundwater zones. (BR)

The Energy-Efficient Quarry: Towards improved understanding and optimisation of energy use and minimisation of CO2 generation in the aggregates industry.

NASA Astrophysics Data System (ADS)

Hill, Ian; White, Toby; Owen, Sarah

2014-05-01

Extraction and processing of rock materials to produce aggregates is carried out at some 20,000 quarries across the EU. All stages of the processing and transport of hard and dense materials inevitably consume high levels of energy and have consequent significant carbon footprints. The FP7 project "the Energy Efficient Quarry" (EE-Quarry) has been addressing this problem and has devised strategies, supported by modelling software, to assist the quarrying industry to assess and optimise its energy use, and to minimise its carbon footprint. Aggregate quarries across Europe vary enormously in the scale of the quarrying operations, the nature of the worked mineral, and the processing to produce a final market product. Nevertheless most quarries involve most or all of a series of essential stages; deposit assessment, drilling and blasting, loading and hauling, and crushing and screening. The process of determining the energy-efficiency of each stage is complex, but is broadly understood in principle and there are numerous sources of information and guidance available in the literature and on-line. More complex still is the interaction between each of these stages. For example, using a little more energy in blasting to increase fragmentation may save much greater energy in later crushing and screening, but also generate more fines material which is discarded as waste and the embedded energy in this material is lost. Thus the calculation of the embedded energy in the waste material becomes an input to the determination of the blasting strategy. Such feedback loops abound in the overall quarry optimisation. The project has involved research and demonstration operations at a number of quarries distributed across Europe carried out by all partners in the EE-Quarry project, working in collaboration with many of the major quarrying companies operating in the EU. The EE-Quarry project is developing a sophisticated modelling tool, the "EE-Quarry Model" available to the quarrying

Analysis of noise pollution in an andesite quarry with the use of simulation studies and evaluation indices.

PubMed

Kosała, Krzysztof; Stępień, Bartłomiej

2016-01-01

This paper presents the verification of two partial indices proposed for the evaluation of continuous and impulse noise pollution in quarries. These indices, together with the sound power of machines index and the noise hazard index at the workstation, are components of the global index of assessment of noise hazard in the working environment of a quarry. This paper shows the results of acoustic tests carried out in an andesite quarry. Noise generated by machines and from performed blasting works was investigated. On the basis of acoustic measurements carried out in real conditions, the sound power levels of machines and the phenomenon of explosion were determined and, based on the results, three-dimensional models of acoustic noise propagation in the quarry were developed. To assess the degree of noise pollution in the area of the quarry, the continuous and impulse noise indices were used.

Alaska research natural areas: 2. Limestone jags.

Treesearch

G.P. Juday

1989-01-01

The 2083-hectare Limestone Jags Research Natural Area in the White Mountains National Recreation Area of central Alaska contains old limestone terrain features––caves, natural bridges, disappearing streams, and cold springs in a subarctic setting. A limestone dissolution joint-type cave in the area is one of the largest reported in high-latitude North America. A...

Noise Exposure and Hearing Capabilities of Quarry Workers in Ghana: A Cross-Sectional Study

PubMed Central

Gyamfi, Charles Kwame R.; Amankwaa, Isaac; Owusu Sekyere, Frank; Boateng, Daniel

2016-01-01

Introduction. Although quarry operations have high economic significance, the effects they cause to the workers in terms of excessive noise production cannot be overlooked. This cross-sectional study assessed the extent of noise exposure and its influence on hearing capabilities among quarry workers in Ashanti region. Methods. The study involved 400 workers randomly selected from five quarries in Ashanti region from April to June 2012. Data was collected using structured questionnaires, physical examination, and audiological assessments. A logistic regression model was fitted to assess independent predictors of hearing loss. Results. All the machines used at the various quarries produced noise that exceeded the minimum threshold with levels ranging from 85.5 dBA to 102.7 dBA. 176 (44%) of study respondents had hearing threshold higher than 25 dBA. 18% and 2% of these were moderately (41–55 dBA) and severely (71–90 dBA) impaired, respectively. Age, duration of work, and use of earplugs independently predicted the development of hearing loss. Use of earplugs showed a protective effect on the development of hearing loss (OR = 0.45; 95% CI = 0.25, 0.84). Conclusion. This study provides empirical evidence on the extent of damage caused to quarry workers as a result of excessive noise exposure. This will support the institution of appropriate protective measures to minimize this threat. PMID:26904137

Comparison of deformation mechanics for two different carbonates: oolitic limestone and laminites

NASA Astrophysics Data System (ADS)

Zihms, Stephanie; Lewis, Helen; Couples, Gary; Hall, Stephen; Somerville, Jim

2016-04-01

Carbonate rocks form under a range of conditions which leads to a diverse rock group. Even though carbonates are overall mineralogically simple, the solid-space distribution ranges from simple compositions such as oolitic limestones to highly complex networks of pores and solids as seen in coquinas. Their fundamental mechanical behaviour has been identified to be like clastic rocks (Vajdova 2004, Brantut, Heap et al. 2014). However it is very likely that this observation is not true for more complex carbonates. Triaxial tests were performed on cylindrical samples of two different carbonates; a) oolitic limestone (Bicqueley quarry, France) and b) laminite (Ariripe basin, Brazil). The samples were deformed under confining pressures of 8, 12 and 20MPa, and 20, 30 and 40MPa, respectively. All tests were stopped as soon as peak load was observed to preserve as many deformation characteristics as possible. Photographs of the samples were taken before and after deformation to allow surface analysis of deformation features. Additionally, samples were analysed post-deformation with X-ray tomography (XRT) (using the Zeiss XRadia XRM 520 at the 4D Imaging Lab at Lund University). The 3D tomography images represent the post-deformation samples' density distribution, allowing detailed, non-destructive, 3D analysis of the deformation features that developed in the triaxial testing, including the complex geometries and interactions of fractures, deformation bands and sedimentary layering. They also provide an insight into the complexity of deformation features produced due to the carbonate response. Initial results show that the oolitic limestone forms single shear bands almost the length of the sample, exhibiting similar characteristics to sandstones deformed under similar conditions. These features are observed for all three applied loads. The laminate sample deformed at the lowest confining pressure exhibits compactive features. However, the laminite samples deformed at the

Field trial of a pulsed limestone diversion well

USGS Publications Warehouse

Sibrell, Philip L.; Denholm, C.; Dunn, Margaret

2013-01-01

The use of limestone diversion wells to treat acid mine drainage (AMD) is well-known, but in many cases, acid neutralization is not as complete as would be desired. Reasons for this include channeling of the water through the limestone bed, and the slow reaction rate of the limestone gravel. A new approach to improve the performance of the diversion well was tested in the field at the Jennings Environmental Education Center, near Slippery Rock, PA. In this approach, a finer size distribution of limestone was used so as to allow fluidization of the limestone bed, thus eliminating channeling and increasing particle surface area for faster reaction rates. Also, water flow was regulated through the use of a dosing siphon, so that consistent fluidization of the limestone sand could be achieved. Testing began late in the summer of 2010, and continued through November of 2011. Initial system performance during the 2010 field season was good, with the production of net alkaline water, but hydraulic problems involving air release and limestone sand retention were observed. In the summer of 2011, a finer size of limestone sand was procured for use in the system. This material fluidized more readily, but acid neutralization tapered off after several days. Subsequent observations indicated that the hydraulics of the system was compromised by the formation of iron oxides in the pipe leading to the limestone bed, which affected water distribution and flow through the bed. Although results from the field trial were mixed, it is believed that without the formation of iron oxides and plugging of the pipe, better acid neutralization and treatment would have occurred. Further tests are being considered using a different hydraulic configuration for the limestone sand fluidized bed.

Characterization of limestone reacted with acid-mine drainage in a pulsed limestone bed treatment system at the Friendship Hill National Historical Site, Pennsylvania, USA

USGS Publications Warehouse

Hammarstrom, J.M.; Sibrell, P.L.; Belkin, H.E.

2003-01-01

Armoring of limestone is a common cause of failure in limestone-based acid-mine drainage (AMD) treatment systems. Limestone is the least expensive material available for acid neutralization, but is not typically recommended for highly acidic, Fe-rich waters due to armoring with Fe(III) oxyhydroxide coatings. A new AMD treatment technology that uses CO2 in a pulsed limestone bed reactor minimizes armor formation and enhances limestone reaction with AMD. Limestone was characterized before and after treatment with constant flow and with the new pulsed limestone bed process using AMD from an inactive coal mine in Pennsylvania (pH = 2.9, Fe = 150 mg/l, acidity = 1000 mg/l CaCO3). In constant flow experiments, limestone is completely armored with reddish-colored ochre within 48 h of contact in a fluidized bed reactor. Effluent pH initially increased from the inflow pH of 2.9 to over 7, but then decreased to 6 during operation. Limestone removed from a pulsed bed pilot plant is a mixture of unarmored, rounded and etched limestone grains and partially armored limestone and refractory mineral grains (dolomite, pyrite). The ???30% of the residual grains in the pulsed flow reactor that are armored have thicker (50- to 100-??m), more aluminous coatings and lack the gypsum rind that develops in the constant flow experiment. Aluminium-rich zones developed in the interior parts of armor rims in both the constant flow and pulsed limestone bed experiments in response to pH changes at the solid/solution interface. ?? 2003 Elsevier Ltd. All rights reserved.

Abandoning wells working group

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The primary objective of this working group is to identify major technical, regulatory, and environmental issues that are relevant to the abandonment of offshore wellbores. Once the issues have been identified, the working group also has the objective of making recommendations or providing potential solutions for consideration. Areas for process improvement will be identified and {open_quotes}best practices{close_quotes} will be discussed and compared to {open_quotes}minimum standards.{close_quotes} The working group will primarily focus on wellbore abandonment in the Gulf of Mexico. However, workshop participants are encouraged to discuss international issues which may be relevant to wellbore abandonment practices in the Gulf ofmore » Mexico. The Abandoning Wells Group has identified several major areas for discussion that have concerns related to both operators and service companies performing wellbore abandonments in the Gulf of Mexico. The following broad topics were selected for the agenda: (1) MMS minimum requirements and state regulations. (2) Co-existence of best practices, new technology, and P & A economics. (3) Liability and environmental issues relating to wellbore abandonment.« less

Abandoned babies and absent policies.

PubMed

Mueller, Joanne; Sherr, Lorraine

2009-12-01

Although infant abandonment is a historical problem, we know remarkably little about the conditions or effects of abandonment to guide evidence driven policies. This paper briefly reviews the existing international evidence base with reference to potential mental health considerations before mapping current UK guidelines and procedures, and available incidence data. Limitations arising from these findings are discussed with reference to international practice, and interpreted in terms of future pathways for UK policy. A systematic approach was utilized to gather available data on policy information and statistics on abandoned babies in the UK. A review of the limited literature indicates that baby abandonment continues to occur, with potentially wide-ranging mental health ramifications for those involved. However, research into such consequences is lacking, and evidence with which to understand risk factors or motives for abandonment is scarce. International approaches to the issue remain controversial with outcomes unclear. Our systematic search identified that no specific UK policy relating to baby abandonment exists, either nationally or institutionally. This is compounded by a lack of accurate of UK abandonment statistics. Data that does exist is not comprehensive and sources are incompatible, resulting in an ambiguous picture of UK baby abandonment. Available literature indicates an absence of clear provision, policy and research on baby abandonment. Based on current understanding of maternal and child mental health issues likely to be involved in abandonment, existing UK strategy could be easily adapted to avoid the 'learning from scratch' approach. National policies on recording and handling of baby abandonments are urgently needed, and future efforts should be concentrated on establishing clear data collection frameworks to inform understanding, guide competent practice and enable successfully targeted interventions.

Exploration for limestone deposit at Onigbedu, South-Western Nigeria

NASA Astrophysics Data System (ADS)

Oyedele, Kayode F.; Oladele, Sunday; Emakpor, Charles A.

2016-09-01

The Onigbedu limestone deposit was investigated using the aeromagnetic data, resistivity soundings and borings with the aim of characterizing the limestone deposit and estimating its reserves. The subsurface structural features and depth to basement were identified with the analysis of aeromagnetic data. Twenty nine boreholes were drilled for subsurface appraisal and correlation of the limestone deposit. Eighty nine Vertical Electrical Sounding (VES) were acquired using the Schlumberger array. The results showed NE-SW trending lineaments that segmented the limestone. Depth to basement varied from 144.2 m to 1090 m. The VES results showed four to six layers indicating the topsoil (7-315 Ωm), clay (2-25 Ωm), shale (6-31 Ωm), limestone (20-223 Ωm), sandstone (>200 Ωm) and sandy materials. The VES results correlated well with the lithological unit delineated from the borehole. The overburden thickness ranged from 3.3 m to 28 m, while the limestone thickness varies between 18.1 m and 48.3 m. The limestone reserve was estimated at 1.9 × 109 t. This study concluded that the study area had vast occurrence of the limestone deposits, which would be of economic importance, if exploited.

Kerford Limestone Company

EPA Pesticide Factsheets

The EPA is providing notice of a proposed Administrative Penalty Assessment against Kerford Limestone Company, for alleged violations at the facility located at 36111 Fletcher Avenue, Weeping Water NE 68463.

Recycling of quarry waste as part of sustainable aggregate production: Norwegian and Italian point of view

NASA Astrophysics Data System (ADS)

Antonella Dino, Giovanna; Willy Danielsen, Svein; Chiappino, Claudia; Primavori, Piero; Engelsen, Christian John

2016-04-01

Resource preservation is one of the main challenges in Europe, together with waste management and recycling; recently several researchers are interested in the recovering of critical raw materials and secondary raw materials from landfill. Aggregate supply, even if it is not "critical" sensus stricto (s.s.), is one of the European priorities (low value but high volume needs). On the other side, the management of quarry waste , mainly from dimension stones, but also as fines from aggregate crushing, is still a matter of concern. Such materials are managed in different ways both locally and nationwide, and often they are landfilled, because of an unclear legislation and a general lack of data. Most of time the local authorities adopt the maximum precaution principle or the enterprises find it little profitable to recover them, so that the sustainable recycling of such material is not valued. Several studies have shown, depending on the material specific characteristics, the viability of recycling quarry waste into new raw materials used in glass and ceramic industries, precast concrete production, infrastructures etc. (Loudes et al. 2012, Dino&Marian 2015, Bozzola et al 2012, Dino et al. 2012, etc.). Thus, aggregate production may be one of the profitable ways to use quarry waste and is falling under the priority of EU (aggregate supply). Positive economic and environmental effects are likely to be achieved by systematic recycling of quarry waste planned by industries (industrial planning) and public authorities (national and local planning of aggregate exploitation). Today, the recycling level varies to a great extent and systematic recovery is not common among European Countries. In Italy and Norway no significant incentives on recycling or systematic approaches for local aggregate exploitation exist. The environmental consequences can be overexploitation of the natural resources, land take for the landfills, environmental contamination and landscape alteration by

Environmental rehabilitation of dismissed quarry areas in the Emilia Apennines (Italy) based on the exploitation of geosites

NASA Astrophysics Data System (ADS)

Soldati, Mauro; Coratza, Paola; Vandelli, Vittoria

2016-04-01

The landscape modifications induced by human activity in the past 50 years, due to quarrying in the catchment of Rio della Rocca (Province of Reggio Emilia, northern Italy) and plans for its environmental rehabilitation, are illustrated. The study area is located in the northern Apennines margin, specifically in the municipality of Castellarano, and is characterised by a great variety of abiotic environments and high biodiversity. As regards the geological aspects of the area, the main lithological outcrops consists of yellow sandstones belonging to the Epi-Ligurian Sequence (Upper Eocene - Lower Oligocene) and grey clays (Lower Pliocene - Lower Pleistocene) of the marine units of the Apennine margin. From a geomorphological viewpoint, the landscape evolution of this valley has been deeply influenced by the presence of rocks with different mechanical behaviour, gravitational and rainwash processes and, more recently, human activities. The latter have played a fundamental role in modelling the physical landscape of the area in recent times. In the Sassuolo area (Province of Modena), very close to the study area, there is the largest tile making district in the world, which was developed during the '60s and '70s of the 20th century, partly thanks to the wide availability of clayey raw materials with suitable technological properties. Since the mid-1950s the study area has been affected by intense quarrying activities which have largely modified its environmental and, in particular, geomorphological features. In the 1970s, three clay pits and four sandstone quarries were active in the area. The clay pits were used for tile production whereas the sandstone materials were utilised in large part for the building industry. This production scenario has radically changed during the past twenty years, with the progressive abandonment of quarries due to the introduction of ever-more restrictive environmental policies, imposing rigorous planning on mining activities

The Research Process on Converter Steelmaking Process by Using Limestone

NASA Astrophysics Data System (ADS)

Tang, Biao; Li, Xing-yi; Cheng, Han-chi; Wang, Jing; Zhang, Yun-long

2017-08-01

Compared with traditional converter steelmaking process, steelmaking process with limestone uses limestone to replace lime partly. A lot of researchers have studied about the new steelmaking process. There are much related research about material balance calculation, the behaviour of limestone in the slag, limestone powder injection in converter and application of limestone in iron and steel enterprises. The results show that the surplus heat of converter can meet the need of the limestone calcination, and the new process can reduce the steelmaking process energy loss in the whole steelmaking process, reduce carbon dioxide emissions, and improve the quality of the gas.

Quarry waste management and recovery: first results connected to Carrara marble ravaneti (Italy)

NASA Astrophysics Data System (ADS)

Antonella Dino, Giovanna; Chiappino, Claudia; Rossetti, Piergiorgio

2017-04-01

Quarry waste (QW) represents a huge economic and environmental issue, due to loss of resources and to economic and environmental costs connected to waste management and landfilling activities. In many cases, valuable Raw Materials (RM) and Secondary Raw Materials (SRM) can be supplied by enhancing the QW recovery. In Italy large amounts of QW have been and still are dumped: such materials, if their quality (chemical, mineralogical, physical characteristics) and quantity are adequate, and if the impacts connected to their management are positive, can represent a valuable resource for SRM exploitation. Several dimension stone quarries have been and are interested by researches as for QW exploitation. Some researches show positive results, which are the basis for QW recovery (both from waste streams and from quarry dumps exploitation): a noticeable example is represented by Carrara marble waste. The Carrara quarry basin is characterized by ca. one hundred quarries for colored and white marble exploitation. The waste production can be summarized in: 80 Mm3 waste present in old quarry dumps (Ravaneti) and 3 Mm3/y of waste stream from quarrying activities. At present only 0.5 Mm3/y of QW is exploited for SRM production, causing a huge loss of resource. This has been the background for a preliminary research, on Carrara marble Ravaneti characterization, which was carried out thanks to the close cooperation between University of Torino, Società Apuana Marmi srl, and SET srl. In 2015, two QW dumping areas, Calocara and Lorano, were selected as representative for sampling activities. Three main sample categories were individuated based on granulometry (0.5-4 mm, 0-25 mm, 0-150 mm) to be characterized (size distribution, density, Atterberg limits, Los Angeles test, freezing and heat tests, flat and shape indexes, geochemistry, mineralogy). The results obtained are promising: the physical characterization shows an attitude for Carrara QW to be recovered as crushed materials

Behavior and Release of Nitrogen at Mines and Quarries in Nordic Conditions

NASA Astrophysics Data System (ADS)

Karlsson, Teemu; Neitola, Raisa; Jermakka, Johannes; Merta, Elina; Mroueh, Ulla-Maija

2015-04-01

The increased extraction of mineral resources and mining activities creates added pressure on the environmental issues and a proper water management in mining areas in Finland. Among others, nitrogen compounds released from explosives or from mining processes can have a detrimental effect on the environment. Thus, this project aimed at comprehensive understanding on the nitrogen issue in the extractive industry. The project collected essential data on nitrogen compounds present in the environments of mines and quarries, and generated better understanding of the discharge and behaviour of nitrogen compounds in mining areas. The sources and balances of explosives-originated nitrogen compounds at mines and quarries of different sizes were investigated and compared. Additionally, the focus was in 'nitrogen smudging' problem of waste rocks and the intensity, as well as evolution and chemical characteristics of their nitrogen contamination. According to the results, the total load of potential nitrogen to the environment depends on the scale and type of the activity as well as the type of explosives used. The main emission sources of nitrogen are process and dewatering waters. A lysimeter study showed that the explosives originated nitrogen content of left over stones from natural stone quarrying is relatively low and ca. half of the nitrogen is leached within the first weeks after detonation. The "nitrogen smudging" of natural stone quarrying left over stones is relatively low to begin with and enhanced by the rapid flushing by rainwater, thus the residues of explosives should not be considered to prevent the utilization of otherwise mineralogically inert waste rocks of good technical quality. The overall nitrogen management should take into account the background concentrations and sensitivity of the local ecosystem. The research project "Solution for Control of Nitrogen Discharges at Mines and Quarries, (MINIMAN)" was realized during years 2012-2014 as a cooperative

Microbial Community Composition and Putative Biogeochemical Functions in the Sediment and Water of Tropical Granite Quarry Lakes.

PubMed

Kumar, Amit; Ng, Daphne H P; Wu, Yichao; Cao, Bin

2018-05-28

Re-naturalized quarry lakes are important ecosystems, which support complex communities of flora and fauna. Microorganisms associated with sediment and water form the lowest trophic level in these ecosystems and drive biogeochemical cycles. A direct comparison of microbial taxa in water and sediment microbial communities is lacking, which limits our understanding of the dominant functions that are carried out by the water and sediment microbial communities in quarry lakes. In this study, using the 16S rDNA amplicon sequencing approach, we compared microbial communities in the water and sediment in two re-naturalized quarry lakes in Singapore and elucidated putative functions of the sediment and water microbial communities in driving major biogeochemical processes. The richness and diversity of microbial communities in sediments of the quarry lakes were higher than those in the water. The composition of the microbial communities in the sediments from the two quarries was highly similar to one another, while those in the water differed greatly. Although the microbial communities of the sediment and water samples shared some common members, a large number of microbial taxa (at the phylum and genus levels) were prevalent either in sediment or water alone. Our results provide valuable insights into the prevalent biogeochemical processes carried out by water and sediment microbial communities in tropical granite quarry lakes, highlighting distinct microbial processes in water and sediment that contribute to the natural purification of the resident water.

Mines, Quarries and Landscape. Visuality and Transformation

NASA Astrophysics Data System (ADS)

Jimeno, Carlos López; Torrijos, Ignacio Díez; González, Carmen Mataix

2016-06-01

In this paper a review of two basic concepts is carried out: scenery and landscape integration, proposing a new concept: "visuality", alternative to the classical "visibility" used in landscape studies related to mining activity, which explores the qualitative aspects that define the visual relationships between observer and environment. In relation to landscape integration studies, some reflections on substantive issues are made which induce certain prejudices at the time of addressing the issue of mining operations landscape integration, and some guidance and integration strategies are formulated. In the second part of the text, a new approach to the landscape integration of mines and quarries is raised, closely linked to the concept of visuality which are based on a basic goal: the re-qualification of the place, and give innovative answers to re-qualify the place and show how to catch the opportunity in the deep transformation generated by the development of mining activities. As a conclusion, a case study is presented in the last section, the landscape integration study conducted on marble exploitations Coto Pinos (Alicante, Spain), considered the largest ornamental rock quarry in Europe.

7. WEST DAM STRUCTURE, LOOKING NORTHWEST. QUARRIES AT BOTTOM; OUTLET ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. WEST DAM STRUCTURE, LOOKING NORTHWEST. QUARRIES AT BOTTOM; OUTLET STRUCTURE UNDER CONSTRUCTION CUTTING INTO HILL AT TOP OF PICTURE. - Eastside Reservoir, Diamond & Domenigoni Valleys, southwest of Hemet, Hemet, Riverside County, CA

Interior of Mess Hall, showing original columns and quarry tile ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior of Mess Hall, showing original columns and quarry tile floor - U.S. Naval Base, Pearl Harbor, Barracks & Mess Hall, Hornet Avenue between Liscome Bay & Enterprise Streets, Pearl City, Honolulu County, HI

Detecting change in water quality from implementation of limestone treatment systems in a coal-minded watershed

USGS Publications Warehouse

Cravotta,, Charles A.; Weitzel, Jeffrey B.

2000-01-01

During 1996-97, a variety of limestone-based treatment systems were implemented to neutralize acidic mine drainage and reduce the transport of dissolved metals in the northern part of the Swatara Creek watershed, which drains a 43-mi2 (112-km2) area in the Southern Anthracite Field upstream from Ravine, Pa. Since 1996, the current project has monitored water quality upstream and downstream of each treatment and at integrator sites on lower reaches of Swatara Creek. Continuous measurements of pH and specific conductance and periodic sampling for alkalinity, acidity, sulfate, and metals upstream and downstream of each treatment system show that (1) open limestone channels and limestone-sand dosing generally had negligible effects on water quality and (2) limestone diversion wells and limestone drains generally were effective at producing near-neutral pH and attenuating dissolved metals during baseflow but were less effective during stormflow conditions. Storm runoff in this area commonly is acidic, and, as streamflow volume increases during stormflow conditions, a smaller fraction of total flow is treated and (or) residence time in the treatment system is reduced. Monitoring on the mainstem of Swatara Creek indicates watershed-scale effects owing primarily to changes in mining practices and secondarily to watershed-wide implementation of treatment systems. Most underground mines in the Swatara Creek Basin were abandoned before 1960 and are presently flooded. Drainage from these mines contributes substantially to baseflow in Swatara Creek. For Swatara Creek at Ravine, Pa., which is immediately downstream of the mined area, long-term data collected since 1959 indicate sulfate concentration declined from about 150 mg/L in 1959 to 75 mg/L in 1999; pH increased sharply from 3.5-4.4 (median ~4) to 4.6-7.0 (median ~6) after 1975. These trends resulted from a decline in pyrite oxidation and the onset of carbonate buffering. Because these long-term attenuation processes have

18 CFR 157.216 - Abandonment.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Abandonment. 157.216 Section 157.216 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT... facilities to be abandoned. (5) For any abandonment resulting in earth disturbance, a USGS 71/2-minute-series...

18 CFR 157.216 - Abandonment.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Abandonment. 157.216 Section 157.216 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT... facilities to be abandoned. (5) For any abandonment resulting in earth disturbance, a USGS 71/2-minute-series...

18 CFR 157.216 - Abandonment.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Abandonment. 157.216 Section 157.216 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT... facilities to be abandoned. (5) For any abandonment resulting in earth disturbance, a USGS 71/2-minute-series...

18 CFR 157.216 - Abandonment.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 18 Conservation of Power and Water Resources 1 2014-04-01 2014-04-01 false Abandonment. 157.216 Section 157.216 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT... facilities to be abandoned. (5) For any abandonment resulting in earth disturbance, a USGS 71/2-minute-series...

18 CFR 157.216 - Abandonment.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Abandonment. 157.216 Section 157.216 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT... facilities to be abandoned. (5) For any abandonment resulting in earth disturbance, a USGS 71/2-minute-series...

Laser removal of graffiti from Pink Morelia Quarry

NASA Astrophysics Data System (ADS)

Penide, J.; Quintero, F.; Riveiro, A.; Sánchez-Castillo, A.; Comesaña, R.; del Val, J.; Lusquiños, F.; Pou, J.

2013-11-01

Morelia is an important city sited in Mexico. Its historical center reflects most of their culture and history, especially of the colonial period; in fact, it was appointed World Heritage Site by UNESCO. Sadly, there is a serious problem with graffiti in Morelia and its historical center is the worst affected since its delicate charming is definitely damaged. Hitherto, the conventional methods employed to remove graffiti from Pink Morelia Quarry (the most used building stone in Morelia) are quite aggressive to the appearance of the monuments, so actually, they are not a very good solution. In this work, we performed a study on the removal of graffiti from Pink Morelia Quarry by high power diode laser. We carried out an extensive experimental study looking for the optimal processing parameters, and compared a single-pass with a multi-pass method. Indeed, we achieved an effective cleaning without producing serious side effects in the stone. In conclusion, the multi-pass method emitting in continuous wave was revealed as the more effective operating modes to remove the graffiti.

Simulation of the effects of nearby quarrying operations on ground-water flow at the South Well Field, Franklin County, Ohio

USGS Publications Warehouse

Nalley, Gregory M.; Haefner, Ralph J.

1999-01-01

The City of Columbus, Ohio, operates a municipal well field in southern Franklin County that is adjacent to a sand and gravel mining operation. Mining operations have the potential to alter ground-water flowpaths and change the sources of water to pumped wells. Previous ground-water-flow modeling of the area has shown that water pumped from the supply wells is derived from infiltration from nearby rivers and surrounding bedrock. Some of that water flows through existing quarries. Because water quality differs among these sources and is affected by the path along which water flows to the wells, five flow conditions were simulated to evaluate the influence of different mining scenarios on sources of water as related to the size and shape of contributing recharge areas (CRAs) to wells. The first simulation was based on a revision of an existing model by Schalk (1996). The second and third simulations included one in which a 20-foot layer of undisturbed aquifer material within the quarry above the bedrock is left intact, and another in which the 20-foot layer is removed. The fourth and fifth simulations included one in which the 20-foot layer of undisturbed aquifer material is left above the bedrock and the quarry is backfilled with fine- grained sand and silt (a byproduct of the mining operations), and another in which the 20-foot layer is removed before the quarry is backfilled with the fine-grained sand and silt. The results of the five model simulations indicate that the overall volumetric budgets among models change only slightly in response to changing conditions at the quarry. The most significant change is noted in the amount of water that the aquifers gained from constant head and river leakage. This change is due to the way the quarries were simulated and lower heads in the aquifers compared to those in simulations made with earlier models. Previously published model simulations showed that the 5-year CRAs did not extend into the area of the newest sand and

Seismo-acoustic analysis of the near quarry blasts using Plostina small aperture array

NASA Astrophysics Data System (ADS)

Ghica, Daniela; Stancu, Iulian; Ionescu, Constantin

2013-04-01

Seismic and acoustic signals are important to recognize different type of industrial blasting sources in order to discriminate between them and natural earthquakes. We have analyzed the seismic events listed in the Romanian catalogue (Romplus) for the time interval between 2011 and 2012, and occurred in the Dobrogea region, in order to determine detection seismo-acoustic signals of quarry blasts by Plostina array stations. Dobrogea is known as a seismic region characterized by crustal earthquakes with low magnitudes; at the same time, over 40 quarry mines are located in the area, being sources of blasts recorded both with the seismic and infrasound sensors of the Romanian Seismic Network. Plostina seismo-acoustic array, deployed in the central part of Romania, consists of 7 seismic sites (3C broad-band instruments and accelerometers) collocated with 7 infrasound instruments. The array is particularly used for the seismic monitoring of the local and regional events, as well as for the detection of infrasonic signals produced by various sources. Considering the characteristics of the infrasound sensors (frequency range, dynamic, sensibility), the array proved its efficiency in observing the signals produced by explosions, mine explosion and quarry blasts. The quarry mines included for this study cover distances of two hundreds of kilometers from the station and routinely generate explosions that are detected as seismic and infrasonic signals with Plostina array. The combined seismo-acoustic analysis uses two types of detectors for signal identification: one, applied for the seismic signal identification, is based on array processing techniques (beamforming and frequency-wave number analysis), while the other one, which is used for infrasound detection and characterization, is the automatic detector DFX-PMCC (Progressive Multi-Channel Correlation Method). Infrasonic waves generated by quarry blasts have frequencies ranging from 0.05 Hz up to at least 6 Hz and

Optimization of Limestone Feed Size of a Pressurized Fluidized Bed Combustor

NASA Astrophysics Data System (ADS)

Shimizu, Tadaaki; Saastamolnen, Jaakko

Limestone attrition is a major cause of loss of limestone during pressurized fluidized bed combustion. In the authors' previous works, the analysis of published results of solid attrition and desulfurization was conducted to determine the attrition rate expression. The specific attrition rate (rate of decrease in diameter) was estimated to be second order with respect to particle diameter in the previous work. This rate expression implies that reduction of feed size of limestone is effective for suppression of loss of limestone by attrition. However, too much grinding of raw limestone will increase the content of fine particles that are readily elutriated by gas stream and do not contribute to the sulfur capture. In this work, modeling works are conducted for particle attrition and desulfurization in order to predict the effect of feed size of limestone on total consumption of limestone and desulfurization is discussed. Optimum particle size to suppress limestone consumption was approximately 0.7 mm (as D p50 ). However, the control of solid drain rate from the bottom was found to have more influence on total limestone consumption rate. Emissions of SO2 from low sulfur coal (S=0.33%) could be sufficiently low irrespective of limestone feed size but SO2 emissions from coals with higher sulfur content than 0.5% were anticipated to increase drastically. Such drastic change in SO2 emissions with the change in sulfur content is attributable to non-linear nature of reaction rate for attrition-enhanced desulfurization by limestone.

The Fossil Fauna of the Islands Region of Western Lake Erie.

ERIC Educational Resources Information Center

Bowe, Lulu M., Comp.

The islands of western Lake Erie are rock-bound isles that abound in rocky outcrops and quarries. The rocks of these islands are of two distinct types, Silurian dolomites and Devonian limestones. The dolomites, exposed in the Bass Islands and Sister Islands are virtually devoid of fossils. Conversely, the limestones of Johnson Island, Marblehead,…

A Metagenomic Survey of Limestone Hill in Taiwan

NASA Astrophysics Data System (ADS)

Hsu, Y. W.; Li, K. Y.; Chen, Y. W.; Huang, T. Y.; Chen, W. J.; Shih, Y. J.; Chen, J. S.; Fan, C. W.; Hsu, B. M.

2016-12-01

The limestone of Narro-Sky in Tainliao, Taiwan is of Pleistocene reef limestones interbedded in clastic layers that covered the Takangshan anticlines. Understanding how microbial relative abundance was changed in response to changes of environmental factors may contribute to better comprehension of roles that microorganisms play in altering the landscape structures. In this study, microorganisms growing on the wall of limestone, in the water dripping from the limestone wall and of soil underneath the wall were collected from different locations where the environmental factors such as daytime illumination, humidity, or pH are different. Next generation sequencing (NGS) was carried out to examine the compositions and richness of microbial community. The metagenomics were clustered into operational taxonomic units (OTUs) to analyze relative abundance, diversities and principal coordinates analysis (PCoA). Our results showed the soil sample has the highest alpha diversity while water sample has the lowest. Four major phyla, which are Proteobacteria, Acidobacteria, Actinobacteria, and Cyanobacteria, account for 80 % of total microbial biomass in all groups. Cyanobacteria were found most abundantly in limestone wall instead of water or soil of weathering limestone. The PCoA dimensional patterns of each phylum showed a trace of microbial community dynamic changes, which might be affected by environmental factors. This study provides the insights to understand how environmental factors worked together with microbial community to shape landscape structures.

Quantification of Reduction in Forced Vital Capacity of Sand Stone Quarry Workers

PubMed Central

Singh, Suresh Kumar; Chowdhary, G. R.; Chhangani, V. D.; Purohit, Gopal

2007-01-01

This study assessed the reduction in forced vital capacity of lungs of sand stone quarry workers exposed to high respirable suspended particulate concentration. The sand stone quarry workers are engaged in different type of activities like drilling, loading and dressing. These different working places have different concentration of RSPM and these workers are exposed to different concentration of RSPM. It is found that exposure duration and exposure concentrations are main factors responsible to damage respiratory tract of worker. It is also revealed from the study that most of the workers are suffering from silicosis if the exposure duration is more than 15 years. PMID:18180540

Mineralogical characterization of the Shelburne marble and the Salem limestone

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGee, E.S.

Samples of Shelburne marble and Salem limestone were selected to represent marbles and limestones used in buildings and monuments. The Royal variety of Shelburne marble is a white marble predominantly composed of calcite but has heterogeneously distributed gray inclusions. The select buff Salem limestone is a beige, homogeneous, fossiliferous limestone, predominantly composed of fragments of echinoderms and bryozoans. The author reports that both samples are appropriate test stones for the National Acid Precipitation Assessment Program stone exposure studies.

CO2 mitigation via accelerated limestone weathering

USGS Publications Warehouse

Rau, Greg H.; Knauss, Kevin G.; Langer, William H.; Caldeira,

2004-01-01

We evaluate accelerated weathering of limestone (AWL: CO2 + CaCO3 + H2O=> Ca2+ + 2HCO3-) as a low-tech, inexpensive, high-capacity, environmentally-friendly CO2 capture and sequestration technology. With access to seawater and limestone being essential to this approach, significant limestone resources are close to most CO2-emitting power plants along the coastal US. Waste fines, representing more than 20% of current US crushed limestone production (>109 tonnes/yr), could be used as an inexpensive source of AWL carbonate. Under such circumstances CO2 mitigation cost could be as low as $3-$4/tonne. More broadly, 10-20% of US point-source CO2 emissions could be treated at $20-$30/tonne CO2. AWL end-solution disposal in the ocean would significantly reduce effects on ocean pH and carbonate chemistry relative to those caused by direct atmospheric or ocean CO2 disposal. Indeed, the increase in ocean Ca2+ and bicarbonate offered by AWL should enhance growth of corals and other calcifying marine organisms.

Hydrogeological features conditioning trophic levels of quarry lakes in western Po plain (north-western Italy)

NASA Astrophysics Data System (ADS)

De Luca, Domenico Antonio; Castagna, Sara; Lasagna, Manuela

2013-04-01

Quarry lakes occur in plains areas due to the extraction of alluvial sand and gravel used for grout and concrete in the construction industry. Excavation depths can reach and intersect the groundwater surface, thus creating a lake. Because of the need to optimize efficiency, the number of active open pit mines has increased in recent years; consequently, the global number of pit lakes will increase in coming decades (Castendyk and Eary 2009; Klapper and Geller 2001; Castro and Moore 2000). Similar to natural lakes, pit lakes are subject to eutrophication process, both during and after quarrying activity; during mining activity, the eutrophic level is strongly controlled by the excavation method. In the Piedmont territory (north-western Italy) there are 70 active quarry lakes, corresponding to approximately 0.1% of the entire plain area. Quarry lakes, located primarily along the main rivers occur in alluvial deposits of the plain area and have average depths between 20 and 30 m (maximum of 60 m deep) and surface areas between 3 and 30 hectares (Castagna 2008). The present study describes the trophic status of 23 active quarry lakes in the Piedmont plain that were evaluated by applying classifications from scientific literature. Currently, the majority of the studied quarry lakes may be defined as mesotrophic or eutrophic according to the trophic state classifications. Based on historic data, lake trophic levels have increased over time, during active mining. At the end of mining activity, further deterioration of water quality was expected, especially for smaller lakes with minimal oxygen stratification and higher levels of nutrients and algal growth. In addition, the paper focuses on the pit lake water quality and pit dimension; From an environmental perspective the excavation of quarry lakes with an appreciable size will likely result in a better safeguard of water quality and enhanced possibilities for lake end use after the cessation of mining. Piedmont quarry

The behavior limestone under explosive load

NASA Astrophysics Data System (ADS)

Orlov, M. Yu; Orlova, Yu N.; Bogomolov, G. N.

2016-11-01

Limestone behavior under explosive loading was investigated. The behavior of the limestone by the action of the three types of explosives, including granular, ammonite and emulsion explosives was studied in detail. The shape and diameter of the explosion craters were obtained. The observed fragments after the blast have been classified as large, medium and small fragments. Three full-scale experiments were carried out. The research results can be used as a qualitative test for the approbation of numerical methods.

Quarry blasts assessment and their environmental impacts on the nearby oil pipelines, southeast of Helwan City, Egypt

NASA Astrophysics Data System (ADS)

Mohamed, Adel M. E.; Mohamed, Abuo El-Ela A.

2013-06-01

Ground vibrations induced by blasting in the cement quarries are one of the fundamental problems in the quarrying industry and may cause severe damage to the nearby utilities and pipelines. Therefore, a vibration control study plays an important role in the minimization of environmental effects of blasting in quarries. The current paper presents the influence of the quarry blasts at the National Cement Company (NCC) on the two oil pipelines of SUMED Company southeast of Helwan City, by measuring the ground vibrations in terms of Peak Particle Velocity (PPV). The seismic refraction for compressional waves deduced from the shallow seismic survey and the shear wave velocity obtained from the Multi channel Analysis of Surface Waves (MASW) technique are used to evaluate the closest site of the two pipelines to the quarry blasts. The results demonstrate that, the closest site of the two pipelines is of class B, according to the National Earthquake Hazard Reduction Program (NEHRP) classification and the safe distance to avoid any environmental effects is 650 m, following the deduced Peak Particle Velocity (PPV) and scaled distance (SD) relationship (PPV = 700.08 × SD-1.225) in mm/s and the Air over Pressure (air blast) formula (air blast = 170.23 × SD-0.071) in dB. In the light of prediction analysis, the maximum allowable charge weight per delay was found to be 591 kg with damage criterion of 12.5 mm/s at the closest site of the SUMED pipelines.

A computational study of particulate emissions from an open pit quarry under neutral atmospheric conditions

NASA Astrophysics Data System (ADS)

Silvester, S. A.; Lowndes, I. S.; Hargreaves, D. M.

2009-12-01

The extraction of minerals from surface mines and quarries can produce significant fugitive dust emissions as a result of site activities such as blasting, road haulage, loading, crushing and stockpiling. If uncontrolled, these emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. The dispersion of pollutant emissions within the atmosphere is principally determined by the background wind systems characterized by the atmospheric boundary layer (ABL). This paper presents an overview of the construction and solution of a computational fluid dynamics (CFD) model to replicate the development of the internal ventilation regime within a surface quarry excavation due to the presence of a neutral ABL above this excavation. This model was then used to study the dispersion and deposition of fugitive mineral dust particles generated during rock blasting operations. The paths of the mineral particles were modelled using Lagrangian particle tracking. Particles of four size fractions were released from five blast locations for eight different wind directions. The study concluded that dependent on the location of the bench blast within the quarry and the direction of the wind, a mass fraction of between 0.3 and 0.6 of the emitted mineral particles was retained within the quarry. The retention was largest when the distance from the blast location to the downwind pit boundary was greatest.

Inelastic Compaction in High-Porosity Limestone Monitored Using Acoustic Emissions

NASA Astrophysics Data System (ADS)

Baud, Patrick; Schubnel, Alexandre; Heap, Michael; Rolland, Alexandra

2017-12-01

We performed a systematic investigation of mechanical compaction and strain localization in Saint-Maximin limestone, a quartz-rich, high-porosity (37%) limestone from France. Our new data show that the presence of a significant proportion of secondary mineral (i.e., quartz) did not impact the mechanical strength of the limestone in both the brittle faulting and cataclastic flow regimes, but that the presence of water exerted a significant weakening effect. In contrast to previously published studies on deformation in limestones, inelastic compaction in Saint-Maximin limestone was accompanied by abundant acoustic emission (AE) activity. The location of AE hypocenters during triaxial experiments revealed the presence of compaction localization. Two failure modes were identified in agreement with microstructural analysis and X-ray computed tomography imaging: compactive shear bands developed at low confinement and complex diffuse compaction bands formed at higher confinement. Microstructural observations on deformed samples suggest that the recorded AE activity associated with inelastic compaction, unusual for a porous limestone, could have been due to microcracking at the quartz grain interfaces. Similar to published data on high-porosity macroporous limestones, the crushing of calcite grains was the dominant micromechanism of inelastic compaction in Saint-Maximin limestone. New P wave velocity data show that the effect of microcracking was dominant near the yield point and resulted in a decrease in P wave velocity, while porosity reduction resulted in a significant increase in P wave velocity beyond a few percent of plastic volumetric strain. These new data highlight the complex interplay between mineralogy, rock microstructure, and strain localization in porous rocks.

A new species of karst-adapted Cnemaspis Strauch, 1887 (Squamata: Gekkonidae) from a threatened karst region in Pahang, Peninsular Malaysia.

PubMed

Grismer, L Lee; Wood, Perry L; Mohamed, Maketab; Chan, Kin Onn; Heinz, Heather M; Sumarli, Alex S-I; Chan, Jacob A; Loredo, Ariel I

2013-12-12

A new species of karst-adapted gekkonid lizard of the genus Cnemaspis Strauch is described from Gua Gunting and Gua Goyang in a karst region of Merapoh, Pahang, Peninsular Malaysia whose unique limestone formations are in immediate danger of being quarried. The new species differs from all other species of Cnemaspis based on its unique suite of morphological and color pattern characters. Its discovery underscores the unique biodiversity endemic to karst regions and adds to a growing list of karst-adapted reptiles from Peninsular Malaysia. We posit that new karst-adapted species endemic to limestone forests will continue to be discovered and these regions will harbor a significant percentage of Peninsular Malaysia's biodiversity and thusly should be conserved rather than quarried.

Diagenesis and porosity preservation in Eocene microporous limestones, South Florida, USA

NASA Astrophysics Data System (ADS)

Maliva, Robert G.; Missimer, Thomas M.; Clayton, Edward A.; Dickson, J. A. D.

2009-05-01

Microporous limestones may contain immobile, capillary-bound (irreducible) water that is only in diffusional contact with mobile pore waters or in some reservoirs may contain producible hydrocarbons. The preservation and distribution of microporosity impact both subsurface fluid flow and solute transport. The diagenesis of microporous limestones has received relatively little attention because their very fine grains and cements are not amenable to standard analytical methods. The Ocala Limestone (Upper Eocene) and upper Avon Park Formation (Middle Eocene) in South Florida contain microporous micritic limestones (mudstones to packstones) that are at an intermediate stage of diagenesis. The limestones have been exposed to the active near-surface environment, but have not yet reached a burial depth sufficient for intense chemical compaction and associated porosity reduction. Nuclear magnetic resonance (NMR) logging allowed for the quantification of total porosity, pore-size distribution, and permeability. The Ocala Limestone and Avon Park Formation have different predominant microfacies and porosity size distributions, but yet both retain total porosities predominantly between 35% and 37%. Estimated microporosities range mostly between 12% and 45%. The mudstones and wackestones of the Ocala Limestone have significantly lower permeabilities (mostly 3 to 12 md) than the wackestones to grainstones of the Avon Park Formation (commonly in the 100 to 3000 md range), which have more mixed and overall coarser pore sizes. Computer modeling using carbon and oxygen stable data indicates that the studied microporous limestones underwent only a low degree of chemical diagenetic alteration, despite likely experiencing episodes of freshwater flushing associated with post-depositional sea-level lowstands. The Ocala Limestone and Avon Park Formation limestones illustrate the general concept that total porosity is often largely preserved through early diagenesis (although may undergo

Metal availability in technosols prepared with composted sewage sludge and limestone outcrop affected by the presence of barley

NASA Astrophysics Data System (ADS)

Román, Alejandro; Navarro-Pedreño, José; Belén Almendro-Candel, María; Gómez, Ignacio; Jordán, Manuel M.; Bech, Jaume

2017-04-01

The use of composted sewage sludge (SSC), and limestone outcrop residue (LOR), is a common practice in soil and land rehabilitation, technosol making, and quarry restoration (Jordán et al. 2008). Both wastes are used to improve the physical, chemical, and biological properties of impoverished soils (Karaca 2004; Jordão et al. 2006; Lovieno et al. 2009). However, the use of compost may have some negative effects on the environment (Navarro-Pedreño et al. 2004; Elridge et al. 2009). Moreover, plants cultivated in technosols can produced changes on the availability of essential and harmful metals and, for this reason, is necessary to made studies to evaluate the availability of metals and the effect of plants in their mobility and toxicity. In this experiment, it has been analyzed the effect of barley in metals availability in four technosols prepared mixing volumes of LOR (100, 98, 95 and 90 %) and SSC (0, 2, 5 and 10%). To determine the solubility and availability, Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn were measured by Lindsay-Norvell extraction procedure. For each technosoil, tree pots with barley (three plants) and three without barley were checked after 3 months A of them were irrigated with 1.5 L/week of tap water. At the end of this time, the metal solubility and availability were higher in soils with the presence of barley than the others. This was especially notorious for Fe and Zn. The presence of root exudates and the reduction of lixiviation due to plant transpiration can explain the highest presence of metals. This result may be considered in rhizosphere related to possible metal toxicity. Keywords: compost, limestone outcrop residues, heavy metals, barley. References: Eldridge SM, Chan KY, Barchia I, Pengelly PK, Katupitiya S, Davis JM (2009) A comparison of surface applied granulated biosolids and poultry litter in terms of risk to runoff water quality on turf farms in Western Sydney, Australia. Agr Ecosyst Environ doi:10.1016/j.agee.2009.07.007 Iovieno

Attrition of limestone by impact loading in fluidized beds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fabrizio Scala; Fabio Montagnaro; Piero Salatino

2007-09-15

The present study addresses limestone attrition and fragmentation associated with impact loading, a process which may occur extensively in various regions of fluidized bed (FB) combustors/gasifiers, primarily the jetting region of the bottom bed, the exit region of the riser, and the cyclone. An experimental protocol for the characterization of the propensity of limestone to undergo attrition/fragmentation by impact loading is reported. The application of the protocol is demonstrated with reference to an Italian limestone whose primary fragmentation and attrition by surface wear have already been characterized in previous studies. The experimental procedure is based on the characterization of themore » amount and particle size distribution of the debris generated upon the impact of samples of sorbent particles against a target. Experiments were carried out at a range of particle impact velocities between 10 and 45 m/s, consistent with jet velocities corresponding to typical pressure drops across FB gas distributors. The protocol has been applied to either raw or preprocessed limestone samples. In particular, the effect of calcination, sulfation, and calcination/recarbonation cycles on the impact damage suffered by sorbent particles has been assessed. The measurement of particle voidage and pore size distribution by mercury intrusion was also accomplished to correlate fragmentation with the structural properties of the sorbent samples. Fragmentation by impact loading of the limestone is significant. Lime displays the largest propensity to undergo impact damage, followed by the sorbent sulfated to exhaustion, the recarbonated sorbent, and the raw limestone. Fragmentation of the raw limestone and of the sulfated lime follows a pattern typical of the failure of brittle materials. The fragmentation behavior of lime and recarbonated lime better conforms to a disintegration failure mode, with an extensive generation of very fine fragments. 27 refs., 9 figs. 1 tab.« less

Volume Computation of a Stockpile - a Study Case Comparing GPS and Uav Measurements in AN Open Pit Quarry

NASA Astrophysics Data System (ADS)

Raeva, P. L.; Filipova, S. L.; Filipov, D. G.

2016-06-01

The following paper aims to test and evaluate the accuracy of UAV data for volumetric measurements to the conventional GNSS techniques. For this purpose, an appropriate open pit quarry has been chosen. Two sets of measurements were performed. Firstly, a stockpile was measured by GNSS technologies and later other terrestrial GNSS measurements for modelling the berms of the quarry were taken. Secondly, the area of the whole quarry including the stockpile site was mapped by a UAV flight. Having considered how dynamic our world is, new techniques and methods should be presented in numerous fields. For instance, the management of an open pit quarry requires gaining, processing and storing a large amount of information which is constantly changing with time. Fast and precise acquisition of measurements regarding the process taking place in a quarry is the key to an effective and stable maintenance. In other words, this means getting an objective evaluations of the processes, using up-to-date technologies and reliable accuracy of the results. Often legislations concerning mine engineering state that the volumetric calculations are to present ±3% accuracy of the whole amount. On one hand, extremely precise measurements could be performed by GNSS technologies, however, it could be really time consuming. On the other hand, UAV photogrammetry presents a fast, accurate method for mapping large areas and calculating stockpiles volumes. The study case was performed as a part of a master thesis.

Care of the abandoned child.

PubMed

Raghunath, M

1991-01-01

Care of abandoned children in India is discussed in terms of reasons for abandonment, the physical condition of the children, and legal categories. The options available currently are the cottage system, sponsorship programs, foster care, or adoption. Child-care and rehabilitation that may be necessary is specified as is the importance of maintaining records. The gaps in child-care are exposed. The role of nongovernmental organization (NGOs) and new legislation in closing the gaps is presented. Abandonment is usually a direct result of poverty, but it can also be caused by mental or physical handicaps or illegitimacy. The numbers of abandoned children may reach 2 million. 40-60% of abandoned infants die during monsoons and summers. The legal categories are privately abandoned, children on remand, or court-committed children. The cottage system emphasizes deinstitutionalization, but there remains a great demand for care. Sponsorship aims to strengthen the family unit to prevent abandonment. Foster care provides an alternative family substitute, but is known only theoretically. Childcare may involve instant hospitalization, care is an institution, or foster care with a suitable family. Nursery care requires discipline in hygiene, sanitation, maintenance of individual medical records, and a general cheerful atmosphere. Records are important for the child in later life and for adoption. Rehabilitation is a sociolegal process which must be done properly or it can jeopardize a child's future security. Despite the Supreme Court guidelines of 1984, there is no uniform system of adoption practices, and the child's interests are overlooked when adoptions are promoted. NGOs play an important role in making social welfare programs work. However their efforts are of limited help without government support and legislation. There is a lack of proper legislation which is outside the control of political and religious interests; e.g., Hindu law only permits adoption of one child of

High resolution seismic tomography imaging of Ireland with quarry blast data

NASA Astrophysics Data System (ADS)

Arroucau, P.; Lebedev, S.; Bean, C. J.; Grannell, J.

2017-12-01

Local earthquake tomography is a well established tool to image geological structure at depth. That technique, however, is difficult to apply in slowly deforming regions, where local earthquakes are typically rare and of small magnitude, resulting in sparse data sampling. The natural earthquake seismicity of Ireland is very low. That due to quarry and mining blasts, on the other hand, is high and homogeneously distributed. As a consequence, and thanks to the dense and nearly uniform coverage achieved in the past ten years by temporary and permanent broadband seismological stations, the quarry blasts offer an alternative approach for high resolution seismic imaging of the crust and uppermost mantle beneath Ireland. We detected about 1,500 quarry blasts in Ireland and Northern Ireland between 2011 and 2014, for which we manually picked more than 15,000 P- and 20,000 S-wave first arrival times. The anthropogenic, explosive origin of those events was unambiguously assessed based on location, occurrence time and waveform characteristics. Here, we present a preliminary 3D tomographic model obtained from the inversion of 3,800 P-wave arrival times associated with a subset of 500 events observed in 2011, using FMTOMO tomographic code. Forward modeling is performed with the Fast Marching Method (FMM) and the inverse problem is solved iteratively using a gradient-based subspace inversion scheme after careful selection of damping and smoothing regularization parameters. The results illuminate the geological structure of Ireland from deposit to crustal scale in unprecedented detail, as demonstrated by sensitivity analysis, source relocation with the 3D velocity model and comparisons with surface geology.

7 CFR 767.51 - Property abandonment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AGRICULTURE SPECIAL PROGRAMS INVENTORY PROPERTY MANAGEMENT Property Abandonment and Personal Property Removal..., manage, and operate the abandoned security property, including marketing perishable security property on...

Testing different discrimination methods between microearthquakes and quarry blasts - a case study in Hungary

NASA Astrophysics Data System (ADS)

Kalocsai, Lilla; Kiszely, Márta; Süle, Bálint; Győri, Erzsébet

2017-04-01

Due to the development of seismological network, increasing number of events have been detected in the last years in Hungary. However about 50% of these shocks were quarry blasts. Therefore decontamination of catalogue for revealing the reliable natural seismicity has become an important task. We have studied the events occurring in the surroundings of Mecsek Hills. The goal of our research was to find the best method to separate earthquakes and quarry blasts. In the first step we have studied the diurnal distributions of the events. Because of different focal mechanisms, the waveforms and amplitudes of arriving phases of earthquakes and quarry blasts are different. We have tested the most typical parameter, the P and S amplitude ratio, which is often used for separation. The waveform similarities have been analyzed using cross-correlation matrix and dendrograms. The earthquakes and the blasts of different quarries have been arranged into different clusters. We have computed spectrograms and because the blasts were carried out by delay-fired technology we have computed binary spectrograms too. Computation of binary spectra is a useful visualization method to recognize the delay-fired explosions, because it emphasizes the long-duration modulations of the spectra. It is made from the original spectra by application of a filter that replaces the spectral amplitudes with a binary code, which simply reflects the local spectral highs and lows. The modulations were present in most of the spectra of blasts and in contrast to the earthquakes, the modulations have been observable until the end of the spectrogram. We also have studied the scalloping and steepness of the spectra.

Permeability hysterisis of limestone during isotropic compression.

PubMed

Selvadurai, A P S; Głowacki, A

2008-01-01

The evolution of permeability hysterisis in Indiana Limestone during application of isotropic confining pressures up to 60 MPa was measured by conducting one-dimensional constant flow rate tests. These tests were carried out either during monotonic application of the confining pressure or during loading-partial unloading cycles. Irreversible permeability changes occurred during both monotonic and repeated incremental compression of the limestone. Mathematical relationships are developed for describing the evolution of path-dependent permeability during isotropic compression.

Effect of limestone particle size and calcium to non-phytate phosphorus ratio on true ileal calcium digestibility of limestone for broiler chickens.

PubMed

Anwar, M N; Ravindran, V; Morel, P C H; Ravindran, G; Cowieson, A J

2016-10-01

The purpose of this study was to determine the effect of limestone particle size and calcium (Ca) to non-phytate phosphorus (P) ratio on the true ileal Ca digestibility of limestone for broiler chickens. A limestone sample was passed through a set of sieves and separated into fine (<0.5 mm) and coarse (1-2 mm) particles. The analysed Ca concentration of both particle sizes was similar (420 g/kg). Six experimental diets were developed using each particle size with Ca:non-phytate P ratios of 1.5:1, 2.0:1 and 2.5:1, with ratios being adjusted by manipulating the dietary Ca concentrations. A Ca-free diet was also developed to determine the basal ileal endogenous Ca losses. Titanium dioxide (3 g/kg) was incorporated in all diets as an indigestible marker. Each experimental diet was randomly allotted to 6 replicate cages (8 birds per cage) and fed from d 21 to 24 post hatch. Apparent ileal digestibility of Ca was calculated using the indicator method and corrected for basal endogenous losses to determine the true Ca digestibility. The basal ileal endogenous Ca losses were determined to be 127 mg/kg of dry matter intake. Increasing Ca:non-phytate P ratios reduced the true Ca digestibility of limestone. The true Ca digestibility coefficients of limestone with Ca:non-phytate P ratios of 1.5, 2.0 and 2.5 were 0.65, 0.57 and 0.49, respectively. Particle size of limestone had a marked effect on the Ca digestibility, with the digestibility being higher in coarse particles (0.71 vs. 0.43).

30 CFR 57.4011 - Abandoned electric circuits.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Abandoned electric circuits. 57.4011 Section 57.4011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... and Control § 57.4011 Abandoned electric circuits. Abandoned electric circuits shall be deenergized...

30 CFR 56.4011 - Abandoned electric circuits.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Abandoned electric circuits. 56.4011 Section 56.4011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Control § 56.4011 Abandoned electric circuits. Abandoned electric circuits shall be deenergized and...

30 CFR 57.4011 - Abandoned electric circuits.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Abandoned electric circuits. 57.4011 Section 57.4011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... and Control § 57.4011 Abandoned electric circuits. Abandoned electric circuits shall be deenergized...

30 CFR 56.4011 - Abandoned electric circuits.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Abandoned electric circuits. 56.4011 Section 56.4011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Control § 56.4011 Abandoned electric circuits. Abandoned electric circuits shall be deenergized and...

30 CFR 57.4011 - Abandoned electric circuits.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Abandoned electric circuits. 57.4011 Section 57.4011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... and Control § 57.4011 Abandoned electric circuits. Abandoned electric circuits shall be deenergized...

30 CFR 56.4011 - Abandoned electric circuits.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Abandoned electric circuits. 56.4011 Section 56.4011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Control § 56.4011 Abandoned electric circuits. Abandoned electric circuits shall be deenergized and...

30 CFR 56.4011 - Abandoned electric circuits.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Abandoned electric circuits. 56.4011 Section 56.4011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Control § 56.4011 Abandoned electric circuits. Abandoned electric circuits shall be deenergized and...

30 CFR 57.4011 - Abandoned electric circuits.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Abandoned electric circuits. 57.4011 Section 57.4011 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... and Control § 57.4011 Abandoned electric circuits. Abandoned electric circuits shall be deenergized...

Retention and transport of graphene oxide in water-saturated limestone media.

PubMed

Dong, Shunan; Sun, Yuanyuan; Gao, Bin; Shi, Xiaoqing; Xu, Hongxia; Wu, Jianfeng; Wu, Jichun

2017-08-01

In this work, column experiments were conducted to investigate the transport characteristics of graphene oxide (GO) nanoparticles in limestone media under various electrolytes, solution pH, and humic acid (HA) concentration conditions. In the limestone media, GO exhibited relatively low mobility with the mass recovery rate lower than 65.2%, even when solution ionic strength was low. The presence of HA enhanced its mobility. In addition, the presence of S 2- , a divalent anion, also promoted GO transport in limestone media compared to Cl - under similar ionic strength conditions through neutralizing more positive charge and thus diminishing the cation bridging. Solution pH showed slight effect on the transport of GO in limestone with the mass recovery range from 40.3% to 51.7%. Over all, decreases in solution pH, HA concentration and increases in solution ionic strength reduced the mobility of GO in the limestone media under the tested conditions. These results indicated both environmental conditions and media characteristics played important roles in controlling GO fate and transport in porous media. The one-site kinetic deposition model was applied to describe the interactions between the GO and limestone media and model simulations fitted the observed experimental data very well. As limestone is an important component of aquiferous media in subsurface, findings from this study elucidated the key factors and processes controlling the fate of GO particles in limestone media, which can inform the prediction and assessment of the risks of GO in groundwater environment. Copyright © 2017 Elsevier Ltd. All rights reserved.

30 CFR 77.215-4 - Refuse piles; abandonment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Refuse piles; abandonment. 77.215-4 Section 77... MINES Surface Installations § 77.215-4 Refuse piles; abandonment. When a refuse pile is to be abandoned... refuse pile shall be abandoned in accordance with a plan submitted by the operator and approved by the...

Characterization of Limestone as Raw Material to Hydrated Lime

NASA Astrophysics Data System (ADS)

Salem Hwidi, Rajeb; Nuraiti Tengku Izhar, Tengku; Saad, Farah Naemah Mohd

2018-03-01

In Malaysia, limestone is essentially important for the economic growth as raw materials in the industry sector. Nevertheless, a little attention was paid to the physical, chemical, mineralogical, and morphological properties of the limestone using X-ray fluorescence (X-RF), X-ray diffraction (X-RD), Fourier transform infrared spectroscopy (FTIR), and Scanning electron microscopy / energy dispersive x-ray spectroscopy (SEM-EDS) respectively. Raw materials (limestone rocks) were collected from Bukit Keteri area, Chuping, Kangar, Perlis, Malaysia. Lab crusher and lab sieved were utilized to prepare five different size of ground limestone at (75 µm, 150 µm, 225 µm, 300, and 425 µm) respectively. It is found that the main chemical composition of bulk limestone was Calcium oxide (CaO) at 97.58 wt.% and trace amount of MnO, Al2O3, and Fe2O3 at 0.02%, 0.35%, and 0.396% respectively. XRD diffractograms showed characteristic peaks of calcite and quartz. Furthermore, main FTIR absorption bands at 1,419, 874.08 and 712.20 cm-1 indicated the presence of calcite. The micrographs showed clearly the difference of samples particle size. Furthermore, EDS peaks of Ca, O, and C elements confirmed the presence of CaCO3 in the samples.

A Method of Effective Quarry Water Purifying Using Artificial Filtering Arrays

NASA Astrophysics Data System (ADS)

Tyulenev, M.; Garina, E.; Khoreshok, A.; Litvin, O.; Litvin, Y.; Maliukhina, E.

2017-01-01

The development of open pit mining in the large coal basins of Russia and other countries increases their negative impact on the environment. Along with the damage of land and air pollution by dust and combustion gases of blasting, coal pits have a significant negative impact on water resources. Polluted quarry water worsens the ecological situation on a much larger area than covered by air pollution and land damage. This significantly worsens the conditions of people living in cities and towns located near the coal pits, and complicates the subsequent restoration of the environment, irreversibly destroying the nature. Therefore, the research of quarry wastewater purifying is becoming an important mater for scholars of technical colleges and universities in the regions with developing open-pit mining. This paper describes the method of determining the basic parameters of the artificial filtering arrays formed on coal pits of Kuzbass (Western Siberia, Russia), and gives recommendations on its application.

The Abandonment of Social Studies?

ERIC Educational Resources Information Center

Griffith, Bryant

1991-01-01

Addresses the question of whether the social studies should be abandoned. Discusses Kieran Egan's analysis of the importance of storytelling and Egan's proposal to abandon the social studies curriculum in favor of a pedagogy more consistent with the way children think. Critiques Egan's view and examines implications for educators. (SG)

Importance of granulometry on phase evolution and phase-to-phase relationships of experimentally burned impure limestones intended for production of hydraulic lime and/or natural cement

NASA Astrophysics Data System (ADS)

Kozlovcev, Petr; Přikryl, Richard; Přikrylová, Jiřina

2015-04-01

In contrast to modern ordinary Portland cement production from finely ground raw material blends, ancient burning of hydraulic lime was conducted by burning larger pieces of natural raw material. Due to natural variability of raw material composition, exploitation of different beds from even one formation can result the product with significantly different composition and/or properties. Prague basin (Neoproterozoic to pre-Variscan Palaeozoic of the central part of the Bohemian Massif - the so-called Barrandian area, Czech Republic) represents a classical example of the limestone-rich region with long-term history of limestone burning for quick lime and/or various types of hydraulic binders. Due to the fact that burning of natural hydraulic lime has been abandoned in this region at the turn of 19th/20th c., significant gap in knowledge on the behavior of various limestone types and on the influence of minor variance in composition on the quality of burned product is encountered. Moreover, the importance of employment of larger pieces of raw material for burning for the development of proper phase-to-phase relationships (i.e. development of hydraulic phases below sintering temperature at mutual contacts of minerals) has not been examined before. To fill this gap, a representative specimens of major limestone types from the Prague basin have been selected for experimental study: Upper Silurian limestone types (Přídolí and Kopanina Lms.), and Lower Devonian limestones (Radotín, Kotýs, Řeporyje, Dvorce-Prokop, and Zlíchov Lms.). Petrographic character of the experimental material was examined by polarizing microscopy, cathodoluminescence, scanning electron microscopy with an energy dispersive spectrometer (SEM-EDS), and X-ray diffraction (XRD) of insoluble residue. Based on the data from wet silicate analyses, modal composition of studied impure limestones was computed. Experimental raw material was burned in laboratory electric furnace at 1000 and 1200°C for 3

Assessment of characteristics and remedial alternatives for abandoned mine drainage : case study at Staple Bend Tunnel unit of Allegheny Portage Railroad National Historic Site, Cambria County, Pennsylvania, 2004

USGS Publications Warehouse

Cravotta, Charles A.

2005-01-01

This report describes field, laboratory, and computational methods that could be used to assess remedial strategies for abandoned mine drainage (AMD). During April-June, 2004, the assessment process was applied to AMD from bituminous coal deposits at a test site in the Staple Bend Tunnel Unit of Allegheny Portage Railroad National Historic Site (ALPO-SBTU) in Cambria County, Pennsylvania. The purpose of this study was (1) to characterize the AMD quantity and quality within the ALPO-SBTU test site; (2) to evaluate the efficacy of limestone or steel slag for neutralization of the AMD on the basis of reaction-rate measurements; and (3) to identify possible alternatives for passive or active treatment of the AMD. The data from this case study ultimately will be used by the National Park Service (NPS) to develop a site remediation plan. The approach used in this study could be applicable at other sites subject to drainage from abandoned coal or metal mines.During April 2004, AMD from 9 sources (sites1, 1Fe, Fe, 2, 3, 3B, 5, 6, and 7) at the ALPO-SBTU test site had a combined flow rate of 1,420 gallons per minute (gal/min) and flow-weighted averages for pH of 3.3, net acidity of 55 milligrams per liter (mg/L) as CaCO3, and concentrations of dissolved sulfate, aluminum, iron, and manganese of 694 mg/L, 4.4 mg/L, 0.74 mg/L, and 1.2 mg/L, respectively. These pH, net acidity, sulfate, and aluminum values exceed effluent criteria for active mines in Pennsylvania.During April-June 2004, limestone and steel slag that were locally available were tested in the laboratory for their composition, approximate surface area, and potential to neutralize samples of the AMD. Although the substrates had a similar particle-size distribution and identical calcium content (43 percent as calcium oxide), the limestone was composed of crystalline carbonates and the slag was composed of silicate glass and minerals. After a minimum of 8 hours contact between the AMD and limestone or steel slag in

Steam Cured Self-Consolidating Concrete and the Effects of Limestone Filler

NASA Astrophysics Data System (ADS)

Aqel, Mohammad A.

The purpose of this thesis is to determine the effect and the mechanisms associated with replacing 15% of the cement by limestone filler on the mechanical properties and durability performance of self-consolidating concrete designed and cured for precast/prestressed applications. This study investigates the role of limestone filler on the hydration kinetics, mechanical properties (12 hours to 300 days), microstructural and durability performance (rapid chloride permeability, linear shrinkage, sulfate resistance, freeze-thaw resistance and salt scaling resistance) of various self-consolidating concrete mix designs containing 5% silica fume and steam cured at a maximum holding temperature of 55°C. This research also examines the resistance to delayed ettringite formation when the concrete is steam cured at 70°C and 82°C and its secondary consequences on the freeze-thaw resistance. The effect of several experimental variables related to the concrete mix design and also the curing conditions are examined, namely: limestone filler fineness, limestone filler content, cement type, steam curing duration and steam curing temperature. In general, the results reveal that self-consolidating concrete containing 15% limestone filler, steam cured at 55°C, 70°C and 82°C, exhibited similar or superior mechanical and transport properties as well as long term durability performance compared to similar concrete without limestone filler. When the concrete is steam cured at 55°C, the chemical reactivity of limestone filler has an important role in enhancing the mechanical properties at 16 hours (compared to the concrete without limestone filler) and compensating for the dilution effect at 28 days. Although, at 300 days, the expansion of all concrete mixes are below 0.05%, the corresponding freeze-thaw durability factors vary widely and are controlled by the steam curing temperature and the chemical composition of the cement. Overall, the material properties indicate that the use

Assessment of occupational exposure in a granite quarry and processing factory.

PubMed

Tejado, J J; Guillén, J; Baeza, A

2016-09-01

Workers in the granite industry face an occupational hazard: silicosis due to the crystalline silica present in inhalable dust. As granite can also present a variable, and occasionally significant, content of naturally occurring radionuclides, they may also face a radiological hazard. In order to assess the risk, a granite industry with a quarry and processing factory was selected to assess the occupational exposure. Three main potential pathways were observed: external irradiation, inhalation of granite dust, and radon exposure. The external dose rate was similar to that in a nearby farming area. A slight increment (0.016-0.076 mSv yr -1 ) was observed in the quarry and stockpile, due to quarry faces and granite blocks. The effective dose due to granite dust inhalation was 0.182  ±  0.009 mSv yr -1 in the worst case scenario (3 mg m -3 dust load in air and no use of filter masks). Thus, the mean value of the effective dose from these two pathways was 0.26 mSv yr -1 , lower than the reference level of 1 mSv yr -1 for the general population. The annual mean value of radon concentration in the indoor air was 33 Bq m -3 . However, during granite processing works the radon concentration can increase up to 216 Bq m -3 , due to mechanical operations (sawing, polishing, sanding, etc). This radon concentration was below the 600 Bq m -3 reference level for action in working places. Therefore, workers in this granite factory face no significant additional radiological exposure, and no-one needs to be designated as occupationally exposed and subject to individual dosimetry.

Tidal rhythmites infine-grained Carboniferous limestones, U.S.A.

USGS Publications Warehouse

Archer, A.W.; Feldman, H.R.

1994-01-01

Analyses of fine-grained limestones reveals that many exhibit fine-scale laminations. Laminations can be normally graded and consist of a coarser-grained lower part and a finer-grained upper part. The upper part can also contain finely disseminated organic material. Despite the similarities of such graded laminae to yearly varves and turbidites, it can be demonstrated by use of laminae-thickness periodicities that some graded laminae are reasonably interpreted as the product of tidal processes. Within siliciclastic systems, modern analogues of such processes are available for comparisons. In fine-grained facies of the Salem Limestone (Visean; Indiana, U.S.A.), periodicities observed within sequential-laminae thicknesses indicate a dominant control by neap-spring tidal processes. Similarly, laminae within limestones of the vertebrate-bearing Hamilton paleochannel (Stephanian; Kansas, U.S.) exhibit similar features, including fine-scale tidal bundles. This limestone is noted for the abundance of articulated fish fossils. Carbonates containing articulated fish from the Wild Cow Formation (Stephanian; New Mexico, U.S.), exhibit diffuse laminations; however, closely associated siliciclastic mudstones contain laminae that exhibit tidal periodicities. There are many similarities between tidal periodicities and patterns of lamination thicknesses of these rocks. A tidal interpretation for these rocks allows for localized, very rapid rates of deposition. Such rapid deposition may, in part, help to explain how articulated fish and other vertebrates can become preserved within such fine-grained limestones. ?? 1994.

Oxic limestone drains for treatment of dilute, acidic mine drainage

USGS Publications Warehouse

Cravotta, Charles A.

1998-01-01

Limestone treatment systems can be effective for remediation of acidic mine drainage (AMD) that contains moderate concentrations of dissolved O2 , Fe3+ , or A13+ (1‐5 mg‐L‐1 ). Samples of water and limestone were collected periodically for 1 year at inflow, outflow, and intermediate points within underground, oxic limestone drains (OLDs) in Pennsylvania to evaluate the transport of dissolved metals and the effect of pH and Fe‐ and Al‐hydrolysis products on the rate of limestone dissolution. The influent was acidic and relatively dilute (pH <4; acidity < 90 mg‐L‐1 ) but contained 1‐4 mg‐L‐1 Of O2 , Fe3+ , A13+ , and Mn2+ . The total retention time in the OLDs ranged from 1.0 to 3.1 hours. Effluent remained oxic (02 >1 mg‐L‐1 ) but was near neutral (pH = 6.2‐7.0); Fe and Al decreased to less than 5% of influent concentrations. As pH increased near the inflow, hydrous Fe and Al oxides precipitated in the OLDs. The hydrous oxides, nominally Fe(OH)3 and AI(OH)3, were visible as loosely bound, orange‐yellow coatings on limestone near the inflow. As time elapsed, Fe(OH)3 and AI(OH)3 particles were transported downflow. During the first 6 months of the experiment, Mn 2+ was transported conservatively through the OLDs; however, during the second 6 months, concentrations of Mn in effluent decreased by about 50% relative to influent. The accumulation of hydrous oxides and elevated pH (>5) in the downflow part of the OLDs promoted sorption and coprecipitation of Mn as indicated by its enrichment relative to Fe in hydrous‐oxide particles and coatings on limestone. Despite thick (~1 mm) hydrous‐oxide coatings on limestone near the inflow, CaCO3 dissolution was more rapid near the inflow than at downflow points within the OLD where the limestone was not coated. The rate of limestone dissolution decreased with increased residence time, pH, and concentrations of Ca2+ and HCO3‐ and decreased PCO2. The following overall reaction shows alkalinity as

Modifying the properties of finely ground limestone by tumbling granulation

NASA Astrophysics Data System (ADS)

Macho, Oliver; Eckert, Maroš; Tomášová, Barbora; Peciar, Peter; Ščasný, Martin; Fekete, Roman; Peciar, Marián

2016-06-01

Calcium carbonate in the form of finely ground limestone is a material that has found its application in a wide range of industries, in the chemical, rubber, agricultural, and paper industries, is used for desulfurization of boilers and other. In civil engineering, ground limestone is used for the production of building materials, plaster and mortar mixtures, as a filler in concrete mixtures, in road construction, and as an essential component of mastic asphalt. This paper deals with examining the modification of the properties of finely ground limestone by the tumbling agglomeration method. It has been shown that the components of concrete with a round grain have a positive effect on the pumping of concrete in comparison with an elongated grain or the rough surface of crushed stone. The experiments will be carried out on a granulation plate using a variety of granulation liquid. The agglomerates and their properties were compared with untreated finely ground limestone, with a focus on detecting changes in compressibility, density and particle size. The output of this paper is a description and graphical representation of the changes in the properties of ground limestone before and after the agglomeration process.

Railroad abandonment.

DOT National Transportation Integrated Search

1997-03-25

Abandonment and discontinuance of railroad service is allowed by federal law which permits a carrier to end its obligation to provide common carrier service over a particular rail line. Although a number of specific reasons may be given for the aband...

Getting cold feet?: Why health care mergers are abandoned.

PubMed

Roos, Anne-Fleur; Postma, Jeroen

2016-01-01

Despite the frequent occurrence and sizeable consequences of merger abandonment in other sectors, there is no thorough understanding of merger abandonment in health care. The purpose of this study is to improve the understanding of determinants of health care merger abandonment. On the basis of the literature on merger abandonment, we formulated a framework on potential determinants of health care merger abandonment. We then constructed a survey that was sent to 70% of all executives of Dutch health care organizations (response rate = 35%, n = 291). We provide descriptive overviews of open, multiple-response, and multiple-choice questions on merger abandonment and use chi-square tests and Fisher's exact tests to test whether abandoned and completed merger processes differ. About 62% of the respondents were involved in at least one merger process during the period of 2005-2012. Thirty-eight percent of these respondents reported that their last merger case ended prematurely (n = 53). The most frequently mentioned determinants of merger abandonment are changing insights on the desirability and feasibility during merger processes, incompatibilities between executives, and insufficient support for the merger from internal stakeholders. We did not find significant relationships between merger abandonment and executives' previous merger experience, degree of organizational diversification, health care sector, size differences, or other organizational differences. Our findings partially confirm results from previous studies, especially with regard to the importance of changing insights and incompatibilities between the involved executives in merger abandonment. We also find that pressure from internal stakeholders, particularly nonexecutive directors, and distrust, fear, and animosity play an important role in merger abandonment. To minimize the organizational and societal costs of abandoned mergers, we advise executives who engage in mergers to construct backup plans with

49 CFR 192.727 - Abandonment or deactivation of facilities.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Abandonment or deactivation of facilities. 192.727... Abandonment or deactivation of facilities. (a) Each operator shall conduct abandonment or deactivation of... pipeline facility or each abandoned onshore pipeline facility that crosses over, under or through a...

49 CFR 195.59 - Abandonment or deactivation of facilities.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Abandonment or deactivation of facilities. 195.59... Abandonment or deactivation of facilities. For each abandoned offshore pipeline facility or each abandoned onshore pipeline facility that crosses over, under or through a commercially navigable waterway, the last...

STEAM INJECTION INTO FRACTURED LIMESTONE AT LORING AIR FORCE BASE

EPA Science Inventory

A research project on steam injection for the remediation of spent chlorinated solvents from fractured limestone was recently undertaken at the former Loring AFB in Limestone, ME. Participants in the project include the Maine Department of Environmental Protection, EPA Region I,...

Limestone weathering rates accelerated by micron-scale grain detachment

NASA Astrophysics Data System (ADS)

Emmanuel, S.; Levenson, Y.

2014-12-01

The weathering rates of carbonate rocks is often thought to be controlled by chemical dissolution, although some studies have suggested that mechanical erosion could also play an important role. Quantifying the rates of the different processes has proved challenging due to the high degree of variability encountered in both field and lab settings. To determine the rates and mechanisms controlling long-term limestone weathering, we analyse a lidar scan of the Western Wall, a Roman period edifice located in Jerusalem. Weathering rates in fine-grained micritic limestone blocks are up to 2 orders of magnitude higher than the average rates estimated for coarse-grained limestone blocks at the same site. In addition, in experiments that use atomic force microscopy to image dissolving micritic limestone, we show that these higher reaction rates could be due to rapid dissolution along micron-scale grain boundaries, followed by mechanical detachment of tiny particles from the surface. Our analysis indicates that micron-scale grain detachment, rather than pure chemical dissolution, could be the dominant erosional mode for fine-grained rocks in many carbonate terrains.

Asbestos exposure during quarrying and processing of serpentinites: a case study in Valmalenco, Central Alps, Northern Italy

NASA Astrophysics Data System (ADS)

Cavallo, A.; Rimoldi, B.

2012-04-01

Serpentinites are metamorphic rocks derived from ultramafics such as peridotites (lherzolites and/or harzburgites), with a typical mineralogical assemblage of antigorite, olivine, diopside and minor magnetite, chlorite and chrysotile. If the rock mass has good geotechnical properties, these stones are quarried because of their wide variety of green shades and outstanding technical properties. Excellent stones are produced in the Malenco Valley, Central Alps (northern Italy, Sondrio): here the geological set-up is dominated by the ultramafic Malenco massif (lower crust-mantle complex), exposed at the Penninic to Austroalpine boundary zone. Different processing operations give origin to valuable products like stoves, funeral monuments, design home appliances; important building element as roof slabs, tiles for floor and wall coverings constitute the main commercial line of production. In this area, good quality long fibre chrysotile asbestos was mined since the XIX century, till the seventies. The asbestos fissures (mostly slip-fiber) are well known in Valmalenco, associated to an important ENE-WSW striking fracture and hydrothermal vein system. Some actual serpentinite quarries "cross" at times tunnels of the old asbestos mines, because the fracture and vein system "guides" the extraction. At present time, this area represents an excellent example of naturally occurring asbestos (NOA). For these reasons, workers' exposure to asbestos during quarrying and processing cannot be ruled out, and must be assessed according to national laws. From 2004 to nowadays, the INAIL Regional Management of Lombardia, with the collaboration of University of Milan-Bicocca, carried out extensive monitoring campaigns both in quarries and in processing laboratories. More than 300 massive samples (rocks and veins) and 250 airborne dust samples were collected during the surveys. One of the main problems in the study of massive serpentinites is the accurate identification of the different

Western Abandoned Uranium Mine Region Maps

EPA Pesticide Factsheets

Map of the Western Abandoned Uranium Mine (AUM) Region, more than 100 abandoned uranium mine claims generally located along the Little Colorado River and Highway 89 in the Cameron, Coalmine Canyon, Bodaway/Gap, and Leupp Chapters in Northern Arizona.

Reducing Energy-Related CO2 Emissions Using Accelerated Limestone Weathering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rau, G H; Knauss, K G; Langer, W H

2004-04-27

Following earlier descriptions, the use and impacts of accelerated weathering of limestone AWL; reaction: CO{sub 2} + H{sub 2}O + CaCO{sub 3} {yields} Ca{sup 2+} + 2(HCO{sub 3}{sup -}) as a CO{sub 2} capture and sequestration method is further explored. Since ready access to the ocean is likely an essential requirement for AWL, it is shown that significant limestone resources are relatively close to a majority of CO{sub 2}-emitting power plants along the coastal US. Furthermore, waste fines, representing more than 20% of current US crushed limestone production (>10{sup 9} tonnes/yr), could be used in many instances as an inexpensivemore » or free source of AWL carbonate. With limestone transportation to coastal sites then as the dominant cost variable, CO{sub 2} sequestration (plus capture) costs of $3-$4/tonne are achievable in certain locations. While there is vastly more limestone and water on earth than that required for AWL to capture and sequester all fossil fuel CO{sub 2} production, the transportation cost of bringing limestone, seawater, and waste CO{sub 2} into contact likely limits the method's applicability to perhaps 10-20% of US point-source emissions. Using a bench-scale laboratory reactor, it is shown that CO{sub 2} sequestration rates of 10{sup -6} to 10{sup -5} moles/sec per m{sup 2} of limestone surface area are readily achievable using seawater. This translates into reaction densities as high as 2 x 10{sup -2} tonnes CO{sub 2} m{sup -3}day{sup -1}, highly dependent on limestone particle size, solution turbulence and flow, and CO{sub 2} concentration. Modeling of AWL end-solution disposal in the ocean shows significantly reduced effects on ocean pH and carbonate chemistry relative to those caused by direct CO{sub 2} disposal into the atmosphere or ocean. In fact the increase in ocean Ca{sup 2+} and bicarbonate offered by AWL should significantly enhance the growth of corals and other marine calcifiers whose health is currently being threatened

Size and performance of anoxic limestone drains to neutralize acdic mine drainagei

USGS Publications Warehouse

Cravotta, C.A.

2003-01-01

Acidic mine drainage (AMD) can be neutralized effectively in underground, anoxic limestone drains (ALDs). Owing to reaction between the AMD and limestone (CaCO3), the pH and concentrations of alkalinity and calcium increase asymptotically with detention time in the ALD, while concentrations of sulfate, ferrous iron, and manganese typically are unaffected. This paper introduces a method to predict the alkalinity produced within an ALD and to estimate the mass of limestone required for its construction on the basis of data from short-term, closed-container (cubitainer) tests. The cubitainer tests, which used an initial mass of 4 kg crushed limestone completely inundated with 2.8 L AMD, were conducted for 11 to 16 d and provided estimates for the initial and maximum alkalinities and corresponding rates of alkalinity production and limestone dissolution. Long-term (5-11 yr) data for alkalinity and CaCO3 flux at the Howe Bridge, Morrison, and Buck Mountain ALDs in Pennsylvania, USA, indicate that rates of alkalinity production and limestone dissolution under field conditions were comparable with those in cubitainers filled with limestone and AMD from each site. The alkalinity of effluent and intermediate samples along the flow path through the ALDs and long-term trends in the residual mass of limestone and the effluent alkalinity were estimated as a function of the computed detention time within the ALD and second-order dissolution rate models for cubitainer tests. Thus, cubitainer tests can be a useful tool for designing ALDs and predicting their performance.

32 CFR 644.494 - Donation, abandonment or destruction.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Donation, abandonment or destruction. 644.494 Section 644.494 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL... Land) § 644.494 Donation, abandonment or destruction. (a) General. Improvements may be abandoned...

32 CFR 644.494 - Donation, abandonment or destruction.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 4 2011-07-01 2011-07-01 false Donation, abandonment or destruction. 644.494 Section 644.494 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL... Land) § 644.494 Donation, abandonment or destruction. (a) General. Improvements may be abandoned...

32 CFR 644.494 - Donation, abandonment or destruction.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 4 2012-07-01 2011-07-01 true Donation, abandonment or destruction. 644.494 Section 644.494 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL... Land) § 644.494 Donation, abandonment or destruction. (a) General. Improvements may be abandoned...

32 CFR 644.494 - Donation, abandonment or destruction.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 4 2013-07-01 2013-07-01 false Donation, abandonment or destruction. 644.494 Section 644.494 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL... Land) § 644.494 Donation, abandonment or destruction. (a) General. Improvements may be abandoned...

32 CFR 644.494 - Donation, abandonment or destruction.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 4 2014-07-01 2013-07-01 true Donation, abandonment or destruction. 644.494 Section 644.494 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL... Land) § 644.494 Donation, abandonment or destruction. (a) General. Improvements may be abandoned...

Seismic scattering attribute for sedimentary classification of nearshore marine quarries for a major beach nourishment project: Case study of Adriatic coastline, Regione Abruzzo (Italy)

NASA Astrophysics Data System (ADS)

Orlando, Luciana; Contini, Paolo; De Girolamo, Paolo

2017-06-01

Of fundamental importance for any major beach nourishment project using marine quarries is a correct sedimentary classification. The main purpose of such a classification is to identify sand with the appropriate features for beach nourishment. This task is more onerous when quarry sediments are heterogeneous and mixed with silt. This is typical of nearshore marine quarries. The presence of excess silt compromises the use of marine quarries because of the water turbidity that may be induced in the nourished beaches, especially when the beaches are protected by defense structures. Here we discuss the use of scattering amplitude of seismic data, acquired with a pinger source (2-10 kHz), to detect and classify the unconsolidated sediment of a marine quarry. A robust correlation was found between this seismic attribute and the silt content in the sediment. The scattering amplitude was numerically calculated from the seismic data and used to map slices of silt content at different depths. The results have been validated with sedimentary analysis of vibra- and rotary cores, and by the dredged material used for the beach nourishment. The marine quarry produced about 1.200.000 m3 of sand used to nourish eight different beach sites along the Adriatic coasts of the Regione Abruzzo (Italy). The large-scale sedimentary assessment of the area was based on seismic boomer data and the evaluation of the volume of dredged sediments on multibeam data surveyed before and after the exploitation of the quarry. The study shows that this approach is effective in sites with high lateral and vertical variations in the percentage of sand in the sediments.

Modeling of Hydration, Compressive Strength, and Carbonation of Portland-Limestone Cement (PLC) Concrete.

PubMed

Wang, Xiao-Yong

2017-01-26

Limestone is widely used in the construction industry to produce Portland limestone cement (PLC) concrete. Systematic evaluations of hydration kinetics, compressive strength development, and carbonation resistance are crucial for the rational use of limestone. This study presents a hydration-based model for evaluating the influences of limestone on the strength and carbonation of concrete. First, the hydration model analyzes the dilution effect and the nucleation effect of limestone during the hydration of cement. The degree of cement hydration is calculated by considering concrete mixing proportions, binder properties, and curing conditions. Second, by using the gel-space ratio, the compressive strength of PLC concrete is evaluated. The interactions among water-to-binder ratio, limestone replacement ratio, and strength development are highlighted. Third, the carbonate material contents and porosity are calculated from the hydration model and are used as input parameters for the carbonation model. By considering concrete microstructures and environmental conditions, the carbon dioxide diffusivity and carbonation depth of PLC concrete are evaluated. The proposed model has been determined to be valid for concrete with various water-to-binder ratios, limestone contents, and curing periods.

Modeling of Hydration, Compressive Strength, and Carbonation of Portland-Limestone Cement (PLC) Concrete

PubMed Central

Wang, Xiao-Yong

2017-01-01

Limestone is widely used in the construction industry to produce Portland limestone cement (PLC) concrete. Systematic evaluations of hydration kinetics, compressive strength development, and carbonation resistance are crucial for the rational use of limestone. This study presents a hydration-based model for evaluating the influences of limestone on the strength and carbonation of concrete. First, the hydration model analyzes the dilution effect and the nucleation effect of limestone during the hydration of cement. The degree of cement hydration is calculated by considering concrete mixing proportions, binder properties, and curing conditions. Second, by using the gel–space ratio, the compressive strength of PLC concrete is evaluated. The interactions among water-to-binder ratio, limestone replacement ratio, and strength development are highlighted. Third, the carbonate material contents and porosity are calculated from the hydration model and are used as input parameters for the carbonation model. By considering concrete microstructures and environmental conditions, the carbon dioxide diffusivity and carbonation depth of PLC concrete are evaluated. The proposed model has been determined to be valid for concrete with various water-to-binder ratios, limestone contents, and curing periods. PMID:28772472

Influence of limestone characteristics on mercury re-emission in WFGD systems.

PubMed

Ochoa-González, Raquel; Díaz-Somoano, Mercedes; Martínez-Tarazona, M Rosa

2013-03-19

This work evaluates the influence of the effect of the properties of limestones on their reactivity and the re-emission of mercury under typical wet scrubber conditions. The influence of the composition, particle size, and porosity of limestones on their reactivity and the effect of sorbent concentration, pH, redox potential, and the sulphite and iron content of the slurry on Hg(0) re-emission was assessed. A small particle size, a high porosity and a low magnesium content increased the high reactivity of the limestones. Moreover, it was found that the higher the reactivity of the sample the greater the amount of mercury captured in the scrubber. Although sulphite ions did not cause the re-emission of mercury from the suspensions of the gypsums, the limestones enriched in iron increased Hg(0) re-emission under low oxygen conditions. It was observed that the low pH values of the gypsum suspensions favored the cocapture of mercury because Fe(2+) formation was avoided. The partitioning of the mercury in the byproducts of the scrubber depended on the impurities of the limestones rather than on their particle size. No leaching of mercury from the gypsum samples occurred suggesting that mercury was either tightly bound to the impurities of the limestone or was transformed into insoluble mercury species.

Devonian Terrestrial Revolution: the palaeoenvironment of the oldest known tetrapod tracks, Zachełmie Quarry, Poland

NASA Astrophysics Data System (ADS)

Niedźwiedzki, G.

2012-04-01

Numerous trackways and isolated prints with digit impressions, which are similar to the foot anatomy of early tetrapods such as Ichthyostega, were found on the three dolomite bed-surfaces in the lower part of the Wojciechowice Formation exposed in the Zachełmie Quarry in the Holy Cross Mountains (south-central Poland), (Niedźwiedzki et al., 2010). The age of the tetrapod track-bearing strata is well-constrained, but the detailed sedimentology of the lower section with tetrapod ichnites is still under study. The Wojciechowice Formation represent one of the first carbonate stages of a transgressive succession that begins with Early Devonian continental to marginal marine clastics and culminates in the development of a Givetian coral-stromatoporoid carbonate platform. The tetrapod track-bearing complex is composed of grey to reddish, thin- to medium-bedded dolomitic shales and marly dolomite mudstones. These deposits from the tetrapod track-bearing horizon lack definitive marine body fossils, and may have formed in a marginal marine environment, e.g. around a coastal lagoon. Mudcracks, columnar peds, root traces, and microbially induced sedimentary structures were found in three distinct pedotypes of very weakly to weakly developed paleosols (Retallack, 2011). Conodonts of the costatus zone (mid-Eifelian) were found 20 m above the uppermost surface with tetrapod tracks in limestones of the upper Wojciechowice Formation, which contain also brachiopod and crinoidal debris. The overlying Kowala Formation is a marine coral limestone and dolostone. The parts of profile with tetrapod ichnites and invertebrate and conodont fossils contain also records of invertebrate traces. Seven ichnotaxa are distributed among four recognized ichnoassemblages. The recognized ichnocoenoses are typical for the shallow-marine (Cruziana ichnofacies) and land-water transitional (Skolithos/Psilonichnus ichnofacies) carbonate depositional environments. The ichnocoenoses are dominated by trace

37 CFR 2.66 - Revival of abandoned applications.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Applicants § 2.66 Revival of abandoned applications. (a) The applicant may file a petition to revive an... for filing a petition to revive an application abandoned because the applicant did not timely respond... proposed response. (c) The requirements for filing a petition to revive an application abandoned because...

Magnetic surveys for locating abandoned wells

USGS Publications Warehouse

,

1995-01-01

Abandoned and unrecorded wells may act as conduits for the contamination of groundwater supplies by oil field brines and other pollutants. The casings of abandoned wells eventually develop leaks, which, if not properly plugged, can allow pollutants to reach freshwater aquifers that supply drinking water. Sources of pollutants include brine ponds, landfill sites, agricultural activities, industrial activities, illegal disposal sites, or accidental spills. The problem is particularly acute in regions where there are old petroleum fields or where water wells have been extensively used for agricultural irrigation. Even urban areas can contain wells that were abandoned and concealed during development. Carefully designed ground magnetic or aeromagnetic surveys can be used to locate abandoned wells by mapping the magnetic disturbances or "anomalies" produced by their steel well casings. The U.S. Geological Survey (USGS) can, at the request of other Federal, State, or local agencies, conduct, process, and interpret such surveys, or it can aid in the design and monitoring of contracts for such surveys.

Microfacies and diagenesis of the reefal limestone, Callovian Tuwaiq Mountain Limestone Formation, central Saudi Arabia

NASA Astrophysics Data System (ADS)

EL-Sorogy, Abdelbaset S.; Almadani, Sattam A.; Al-Dabbagh, Mohammad E.

2016-03-01

In order to document the microfacies and diagenesis of the reefal limestone in the uppermost part of the Callovian Tuwaiq Mountain Limestone Formation at Khashm Al-Qaddiyah area, central Saudi Arabia, scleractinian corals and rock samples were collected and thin sections were prepared. Coral framestone, coral floatstone, pelloidal packstone, bioclastic packstone, bioclastic wacke/packstone, algal wackestone and bioclastic foraminiferal wacke/packstone were the recorded microfacies types. Cementation, recrystallization, silicification and dolomitization are the main diagenetic alterations affected the aragonitic skeletons of scleractinian corals. All coral skeletons were recrystallized, while some ones were dolomitized and silicified. Microfacies types, as well as the fossil content of sclearctinian corals, bivalves, gastropods, brachiopods and foraminifera indicated a deposition in environments ranging from shelf lagoon with open circulation in quiet water below wave base to shallow reef flank and organic build up for the uppermost reefal part of the Tuwaiq Formation in the study area.

Effective stress law for the permeability and deformation of four porous limestones

NASA Astrophysics Data System (ADS)

Wang, Y.; Meng, F.; Wang, X.; Baud, P.; Wong, T. F.

2017-12-01

The effective stress behavior of a rock is related to the geometric of its pore space. In a microscopically homogeneous assemblage, effective stress coefficients for permeability, volumetric strain and porosity change are predicted to be equal to or less than unity. Experimental measurements are in basic agreement with this prediction, with exceptions particularly in clay-rich sandstones, for which effective stress coefficient for permeability up to 7 was documented. Little is known about carbonates, but Ghabezloo et al. [2009] studied the permeability of an oolitic limestone (from Nimes, France) with 17% porosity and reported effective stress coefficients up to 2.4. We investigated this phenomenon in Indiana, Leitha, Purbeck, and Thala limestones with porosities of 13-30%. Measurements were made at room temperature on water-saturated samples at confining and pore pressures of 7-15 MPa and 1-3 MPa, respectively. Unlike previous studies limited to the permeability, we also determined the effective stress coefficients for volumetric strain and porosity change. Indiana limestone is oolitic, and not surprisingly its behaviour was similar to Nimes limestone, with an effective stress coefficient for permeability of 2.5. Our Indiana limestone data showed that whereas the effective stress coefficient for volumetric strain was <1, that for porosity change was >1. Measurements on Purbeck and Thala limestones are consistent with these inequalities, with effective stress coefficients for permeability and porosity change >1 and that for volumetric strain <1. Even though Purbeck and Thala limestones are micritic with appreciable amount of quartz and dolomite, microstructural and mercury porosimetry data showed that their pore spaces are similar to the oolitic limestones, in that the pore size distribution is bimodal with significant fractions of both macropores and micropores. Berryman [1992] analyzed theoretically a rock made up of two porous constituents. Our new data are in

Stratigraphy and sedimentology of the Upper Cretaceous (Campanian) Anacacho Limestone, Texas, USA

USGS Publications Warehouse

Swezey, C.S.; Sullivan, E.C.

2004-01-01

The Upper Cretaceous Anacacho Limestone is exposed in outcrops between the cities of San Antonio and Del Rio, Texas. A detailed study of four outcrops (Blanco Creek section, Sabinal River section, Seco Creek section, Hondo Creek section) shows that the Anacacho Limestone rests on the Upson Clay (which contains fauna of early Campanian age) and is overlain by the Corsicana Marl (which contains fauna of early Maastrichtian age). An unconformity within the Anacacho Limestone is used herein to separate the limestone into a lower member and an upper member. The lower Anacacho member contains fauna of early Campanian age, whereas the upper Anacacho member contains fauna of middle Campanian age. The lower Anacacho member consists predominantly of wackestones to packstones, which are overlain by packstones to grainstones capped by the unconformity. This unconformity is interpreted as a marine flooding surface, delineating a transition from carbonate grainstones deposited in shallow water (<30 m depth) to a chalk deposited in deeper water. Above the unconformity, the upper Anacacho member is characterized by a chalk, overlain by wackestones and packstones. The uppermost section of the Anacacho Limestone consists of packstones and grainstones with abundant and diverse fossils. Most of the Anacacho Limestone developed in relatively shallow water (<50 m depth) leeward of a large carbonate build-up (possibly a rudistid reef) that now comprises the Anacacho Mountains. The environment, however, was open to marine water throughout deposition of the Anacacho Limestone. ?? 2004 Elsevier Ltd. All rights reserved.

37 CFR 1.138 - Express abandonment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 37 Patents, Trademarks, and Copyrights 1 2010-07-01 2010-07-01 false Express abandonment. 1.138 Section 1.138 Patents, Trademarks, and Copyrights UNITED STATES PATENT AND TRADEMARK OFFICE, DEPARTMENT OF... Patent and Trademark Office. Express abandonment of the application may not be recognized by the Office...

32 CFR 636.31 - Abandoned vehicles.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Abandoned vehicles. 636.31 Section 636.31... CRIMINAL INVESTIGATIONS MOTOR VEHICLE TRAFFIC SUPERVISION (SPECIFIC INSTALLATIONS) Fort Stewart, Georgia § 636.31 Abandoned vehicles. (a) Any MP or DOD police officer who finds or has knowledge of a motor...

32 CFR 636.31 - Abandoned vehicles.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 4 2011-07-01 2011-07-01 false Abandoned vehicles. 636.31 Section 636.31... CRIMINAL INVESTIGATIONS MOTOR VEHICLE TRAFFIC SUPERVISION (SPECIFIC INSTALLATIONS) Fort Stewart, Georgia § 636.31 Abandoned vehicles. (a) Any MP or DOD police officer who finds or has knowledge of a motor...

32 CFR 636.31 - Abandoned vehicles.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 4 2012-07-01 2011-07-01 true Abandoned vehicles. 636.31 Section 636.31... CRIMINAL INVESTIGATIONS MOTOR VEHICLE TRAFFIC SUPERVISION (SPECIFIC INSTALLATIONS) Fort Stewart, Georgia § 636.31 Abandoned vehicles. (a) Any MP or DOD police officer who finds or has knowledge of a motor...

32 CFR 636.31 - Abandoned vehicles.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 4 2014-07-01 2013-07-01 true Abandoned vehicles. 636.31 Section 636.31... CRIMINAL INVESTIGATIONS MOTOR VEHICLE TRAFFIC SUPERVISION (SPECIFIC INSTALLATIONS) Fort Stewart, Georgia § 636.31 Abandoned vehicles. (a) Any MP or DOD police officer who finds or has knowledge of a motor...

32 CFR 636.31 - Abandoned vehicles.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 4 2013-07-01 2013-07-01 false Abandoned vehicles. 636.31 Section 636.31... CRIMINAL INVESTIGATIONS MOTOR VEHICLE TRAFFIC SUPERVISION (SPECIFIC INSTALLATIONS) Fort Stewart, Georgia § 636.31 Abandoned vehicles. (a) Any MP or DOD police officer who finds or has knowledge of a motor...

Novel Hydroxyapatite Coatings for the Conservation of Marble and Limestone

NASA Astrophysics Data System (ADS)

Naidu, Sonia

Marble and limestone are calcite-based materials used in the construction of various structures, many of which have significant artistic and architectural value. Unfortunately, due to calcite's high dissolution rate, these stones are susceptible to chemically-induced weathering in nature. Limestone, due to its inherent porosity, also faces other environmental weathering processes that cause weakening from disintegration at grain boundaries. The treatments presently available are all deficient in one way or another. The aim of this work is to examine the feasibility of using hydroxyapatite (HAP) as a novel protective coating for marble and limestone, with two goals: i) to reduce acid corrosion of marble and ii) to consolidate physically weathered limestone. The motivation for using HAP is its low dissolution rate and structural compatibility with calcite. Mild, wet chemical synthesis routes, in which inorganic phosphate-based solutions were reacted with marble and limestone, alone and with other precursors, were used to produce HAP films. Film nucleation, growth and phase evolution were studied on marble to understand film formation and determine the optimal synthesis route. An acid resistance test was developed to investigate the attack mechanism on marble and quantify the efficacy of HAP-based coatings. Film nucleation and growth were dependent on substrate surface roughness and increased with calcium and carbonate salt additions during synthesis. Acid attack on marble occurred via simultaneous dissolution at grain boundaries, twin boundaries and grain surfaces. HAP provided intermediate protection against acid attack, when compared to two conventional treatments. Its ability to protect the stone from acid was not as significant as predicted from dissolution kinetics and this was attributed to incomplete coverage and residual porosity within the film, arising from its flake-like crystal growth habit, which enabled acid to access the underlying substrate. The

Specification aggregate quarry expansion: a case study demonstrating sustainable management of natural aggregate resources

USGS Publications Warehouse

Langer, William H.; Tucker, M.L.

2003-01-01

Many countries, provinces, territories, or states in the European Union, Australia, Canada, the United States, and elsewhere have begun implementing sustainability programs, but most of those programs stop short of sustainable management of aggregate resources. Sustainable practices do not always have to be conducted under the title of sustainability. This case study describes how Lafarge, a large multinational construction materials supplier, implemented the principles of sustainability even though there was an absence of existing local government policies or procedures addressing sustainable resource management. Jefferson County, Colorado, USA, is one of three counties in the six-county Denver, Colorado, region that has potentially available sources of crushed stone. Crushed stone comprises 30 percent of the aggregate produced in the area and plays a major role in regional aggregate resource needs. Jefferson County is home to four of the five crushed stone operations in the Denver region. Lafarge operates one of those four quarries. Lafarge recently proposed to expand its reserves by exchanging company-owned land for existing dedicated open space land adjacent to their quarry but owned by Jefferson County. A similar proposal submitted about 10 years earlier had been denied. Contrary to the earlier proposal, which was predicated on public relations, the new proposal was predicated on public trust. Although not explicitly managed under the moniker of sustainability, Lafarge used basic management principles that embody the tenets of sustainability. To achieve the goals of sustainable aggregate management where no governmental policies existed, Lafarge not only assumed their role of being a responsible corporate and environmental member of the community, but also assumed the role of facilitator to encourage and enable other stakeholders to responsibly resolve legitimate concerns regarding the Lafarge quarry proposal. Lafarge successfully presented an enlightened

55. QUARRY TILE CUTTERS, SECOND FLOOR, NORTH WING. WORKERS PRESSED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

55. QUARRY TILE CUTTERS, SECOND FLOOR, NORTH WING. WORKERS PRESSED THE CUTTERS INTO SLABS OF CLAY, LIFTED THEM ONTO DRYING BOARDS AND PRESSED THE PLUNGERS TO RELEASE THE CUT TILES. REPRODUCTIONS CUTTERS ARE NOT USED IN PRODUCTION. WOODEN FORMS FOR PRODUCING CLAY SLABS WITH ROLLING PINS REST AGAINST THE WALL. - Moravian Pottery & Tile Works, Southwest side of State Route 313 (Swamp Road), Northwest of East Court Street, Doylestown, Bucks County, PA

Toxicity of acid mine pit lake water remediated with limestone and phosphorus.

PubMed

Neil, Luke L; McCullough, Clint D; Lund, Mark A; Evans, Louis H; Tsvetnenko, Yuri

2009-11-01

Pit lakes are increasingly common worldwide and have potential to provide many benefits. However, lake water toxicity may require remediation before beneficial end uses can be realised. Three treatments to remediate AMD (pH approximately 4.8) pit lake water containing elevated concentrations of Al and Zn from Collie, Western Australia were tested in mesocosms. Treatments were: (a) limestone neutralisation (L), (b) phosphorus amendment (P), and (c) combined limestone neutralisation and phosphorus amendment (L+P). Laboratory bioassays with Ceriodaphnia cf. dubia, Chlorella protothecoides and Tetrahymena thermophila assessed remediation. Limestone neutralisation increased pH and reduced heavy metal concentrations by 98% (Al) to 14% (Mg), removing toxicity to the three test species within 2 months. Phosphorus amendment removed toxicity after 6 months of treatment. However, phosphorus amendment to prior limestone neutralisation failed to reduce toxicity more than limestone neutralisation alone. Low concentrations of both phosphorus and nitrogen appear to limit phytoplankton population growth in all treatments.

Toxicity of acid mine pit lake water remediated with limestone and phosphorus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neil, L.L.; McCullough, C.D.; Lund, M.A.

2009-11-15

Pit lakes are increasingly common worldwide and have potential to provide many benefits. However, lake water toxicity may require remediation before beneficial end uses can be realised. Three treatments to remediate AMD (pH similar to 4.8) pit lake water containing elevated concentrations of Al and Zn from Collie, Western Australia were tested in mesocosms. Treatments were: (a) limestone neutralisation (L), (b) phosphorus amendment (P), and c) combined limestone neutralisation and phosphorus amendment (L+P). Laboratory bioassays with Ceriodaphnia cf. dubia, Chlorella protothecoides and Tetrahymena thermophila assessed remediation. Limestone neutralisation increased pH and reduced heavy metal concentrations by 98% (Al) to 14%more » (Mg), removing toxicity to the three test species within 2 months. Phosphorus amendment removed toxicity after 6 months of treatment. However, phosphorus amendment to prior limestone neutralisation failed to reduce toxicity more than limestone neutralisation alone. Low concentrations of both phosphorus and nitrogen appear to limit phytoplankton population growth in all treatments.« less

40 CFR 144.63 - Financial assurance for plugging and abandonment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... current plugging and abandonment cost estimate, except as provided in § 144.70(g), divided by the number... days after receiving bills for plugging and abandonment activities, the Regional Administrator will... abandonment activities, the Regional Administrator will determine whether the plugging and abandonment...

Who Says There Is No Life after Abandonment? A Grounded Theory on the Coping of Abandoned Filipino Elderly in Nursing Homes

ERIC Educational Resources Information Center

de Guzman, Allan B.; Lacorte, Jeremy C.; Lacsamana, Andrea Keith G.; Lagac, Mark Lawrence M.; Laguador, Jobel M.; Lapid, Jazminn Jessica R.; Lee, Lyndcie Miriele C.

2012-01-01

Cases of abandoned elderly are increasing worldwide. By and large, this group struggles with the sudden change in living arrangement as well as abandonment by their families. Consequently, many elderly are forced into living in nursing homes for the remainder of their lives. Abandonment among these elderly negatively affects how they view…

Reducing energy-related CO2 emissions using accelerated weathering of limestone

USGS Publications Warehouse

Rau, Greg H.; Knauss, Kevin G.; Langer, William H.; Caldeira, Ken

2007-01-01

The use and impacts of accelerated weathering of limestone (AWL; reaction: CO2+H2O+CaCO3→Ca2++2(HCO3-) is explored as a CO2 capture and sequestration method. It is shown that significant limestone resources are relatively close to a majority of CO2-emitting power plants along the coastal US, a favored siting location for AWL. Waste fines, representing more than 20% of current US crushed limestone production (>109 tonnes/yr), could provide an inexpensive or free source of AWL carbonate. With limestone transportation then as the dominant cost variable, CO2 mitigation costs of $3-$4/tonne appear to be possible in certain locations. Perhaps 10–20% of US point–source CO2 emissions could be mitigated in this fashion. It is experimentally shown that CO2 sequestration rates of 10-6 to 10-5 moles/sec per m2 of limestone surface area are achievable, with reaction densities on the order of 10-2 tonnes CO2 m-3day-1, highly dependent on limestone particle size, solution turbulence and flow, and CO2 concentration. Modeling shows that AWL would allow carbon storage in the ocean with significantly reduced impacts to seawater pH relative to direct CO2 disposal into the atmosphere or sea. The addition of AWL-derived alkalinity to the ocean may itself be beneficial for marine biota.

Evolution of the alteration process in time of granitic materials from Valdemorillo quarries used in built heritage, Madrid, Spain

NASA Astrophysics Data System (ADS)

Alvarez de Buergo, M.; Fort, R.; Perez-Monserrat, E. M.

2012-04-01

Alteration of building materials used for heritage construction already starts in the quarries, where materials are subjected to both natural alteration and anthropic decay, this latter caused by the rock extracting, cutting and carving processes. Once the materials are placed in the building, they are exposed to other agents that accelerate their decay, especially if they are exposed to aggressive environments. Materials petrophysical properties tend to vary according to the alteration degree they have experienced, the longer they have been exposed to decay agents, the greater the properties change. Surface hardness of granitic rocks tend to diminish when they deteriorate, increasing its porosity, which usually is reflected on a decrease of the ultrasound propagation velocity measurements. Ultrasound velocity and surface hardness were measured in 200 monzogranite ashlars use to build the Assumption of Our Lady church (Valdemorillo, Madrid, Spain). Ultrasound velocity was measured using the indirect transmission mode, with 54 kHz frequency transductors, and surface hardness by means of the Schmidt hammer rebound tester. This monument was erected in different building stages. The starting point was a Mozarab or Visigoth defensive tower (8th century). Templars readapt it to a castle-convent (12th and 14th centuries), the tower being converted into a higher bell-tower. During the 14th-15th centuries the Cistercian Order made significant modifications of the complex, being the construction of the Chapter House one of the last enlargements during the 17th century. The quarries located in the surroundings of the monument were used for the first building stages. In the recent fronts of these quarries that have been used along the 20th century, ultrasound and hardness measurements were performed to obtain the values of these parameters in unaltered materials to compare them to those measured in ashlars from different constructive periods. A total of 50 recent front

Diagenetic comparisons between non-tropical Cenozoic limestones of New Zealand and tropical Mississippian limestones from Indiana, USA: Is the non-tropical model better than the tropical model?

NASA Astrophysics Data System (ADS)

Dodd, J. Robert; Nelson, Campbell S.

1998-10-01

Mississippian limestones exposed in Indiana, U.S.A., were deposited in a shallow tropical ocean. However, many properties of these limestones are more like those of modern and Cenozoic non-tropical limestones such as those found in New Zealand. The dominant skeletal grains in the Indiana limestones are calcitic echinoderms, bryozoans, and brachiopods. The dominant skeletal grains in most Cenozoic limestones of New Zealand are calcitic bryozoans, echinoderms, bivalve molluscs, and foraminifera. In contrast, modern and Cenozoic tropical limestones contain an abundance of aragonitic green algae, corals, and molluscs. Early in diagenesis the metastable aragonite dissolves and reprecipitates as calcite, causing early cementation of the sediments. Originally aragonitic fossils that have dissolved can be identified as molds that are commonly filled with secondary calcite. Because they contained little aragonite, most of the Indiana and New Zealand limestones did not have an abundant source of early cement. Except for local cases in which grains were cemented in contact with carbonate supersaturated seawater, grainstones were relatively deeply buried with little cement between the grains. This resulted in mechanical and chemical compaction of skeletal grains, producing a `fitted fabric' with greatly reduced pore space, either open or filled with cement between the grains. Cement in these aragonite-poor grainstones comes largely from pressure dissolution between grains and along stylolitic seams in the rock, features that are common only after burial beyond a few hundred meters. The final product of deeply buried (up to 2000 m) Cenozoic New Zealand grainstones is similar to the Mississippian grainstones of Indiana. In the Indiana limestones we have only the final product of this extensive burial diagenesis. However, the New Zealand sediments and rocks reveal all steps of formation of the final deeply buried limestone. The reason for the scarcity of originally aragonitic

Crimes and misdemeanours: the case of child abandonment.

PubMed

Giordano, S

2007-01-01

In 2002, a child was abandoned in a Burger King restaurant in Amsterdam by a Chinese woman, who hoped that the baby would be picked up by someone able to give the child a better life. She was convicted for child abandonment and imprisoned. Whereas some forms of child abandonment are criminalised, others are socially accepted and not even on the ethics agenda. This paper is an invitation to reflect on the inconsistency in the ways in which we prosecute, punish or try to correct some forms of child abandonment and yet make allowances for others.

Comparative study of modified bitumen binder properties collected from mixing plant and quarry.

NASA Astrophysics Data System (ADS)

Mustafa Kamal, M.; Abu Bakar, R.; Hadithon, K. A.

2017-11-01

Quality control and assurance are essential in pavement construction. In general, the properties of bitumen change as it ages in bulk storage, transport, and storage on site. The minimization of bituminous hardening during storing, transportation and mixing depends on careful control of binder temperature. Hence therefore, bitumen should always be stored and handled at the lowest temperature possible, consistent with efficient use. The objective of the work is to monitor the quality of bitumen samples collected from mixing plant and quarry. Results showed that, samples modified bitumen which collected from quarry showed some adverse effects on rheological properties and physical properties after subjecting to high temperature storage within a period of time. The dynamic stiffness, elastic properties and other common binder properties were deteriorated too. The chemical changes that occurred during storage were analysed using Fourier transform infra-red spectroscopy (FTIR). Thus studies developed an understanding of bitumen ageing in storage.

Kinematic hardening of a porous limestone

NASA Astrophysics Data System (ADS)

Cheatham, J. B.; Allen, M. B.; Celle, C. C.

1984-10-01

A concept for a kinematic hardening yield surface in stress space for Cordova Cream limestone (Austin Chalk) developed by Celle and Cheatham (1981) has been improved using Ziegler's modification of Prager's hardening rule (Ziegler, 1959). Data to date agree with the formulated concepts. It is shown how kinematic hardening can be used to approximate the yield surface for a wide range of stress states past the initial yield surface. The particular difficulty of identifying the yield surface under conditions of unloading or extension is noted. A yield condition and hardening rule which account for the strain induced anisotropy in Cordova Cream Limestone were developed. Although the actual yield surface appears to involve some change of size and shape, it is concluded that true kinematic hardening provides a basis for engineering calculations.

Magnetic properties and element concentrations in lichens exposed to airborne pollutants released during cement production.

PubMed

Paoli, Luca; Winkler, Aldo; Guttová, Anna; Sagnotti, Leonardo; Grassi, Alice; Lackovičová, Anna; Senko, Dušan; Loppi, Stefano

2017-05-01

The content of selected elements (Al, As, Ca, Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, S, Ti, V and Zn) was measured in samples of the lichen Evernia prunastri exposed for 30, 90 and 180 days around a cement mill, limestone and basalt quarries and urban and agricultural areas in SW Slovakia. Lichens transplanted around the investigated quarries and the cement mill rapidly (30 days) reflected the deposition of dust-associated elements, namely Ca (at the cement mill and the limestone quarry) and Fe, Ti and V (around the cement mill and the basalt quarry), and their content remained significantly higher throughout the whole period (30-180 days) with respect to the surrounding environment. Airborne pollutants (such as S) progressively increased in the study area from 30 to 180 days. The magnetic properties of lichen transplants exposed for 180 days have been characterized and compared with those of native lichens (Xanthoria parietina) and neighbouring bark, soil and rock samples, in order to test the suitability of native and transplanted samples as air pollution magnetic biomonitors. The magnetic mineralogy was homogeneous in all samples, with the exception of the samples from the basalt quarry. The transplants showed excellent correlations between the saturation remanent magnetization (Mrs) and the content of Fe. Native samples had a similar magnetic signature, but the values of the concentration-dependent magnetic parameters were up to two orders of magnitude higher, reflecting higher concentrations of magnetic particles. The concentrations of As, Ca and Cr in lichens correlated with Mrs values after neglecting the samples from the basalt quarry, which showed distinct magnetic properties, suggesting the cement mill as a likely source. Conversely, Ti and Mn were mostly (but not exclusively) associated with dust from the basalt quarry. It is suggested that the natural geological characteristics of the substrate may strongly affect the magnetic properties of lichen thalli

Use of limestone screenings in S-5 surface mixes : final report.

DOT National Transportation Integrated Search

1982-01-01

It is often practical to use limestone screenings in non-polishing S-5 surface mixes in some western areas of Virginia. Also, there has been some conjecture that limestone increases the durability of these mixes. Although the fine aggregate usually h...

Role of transient water pressure in quarrying: A subglacial experiment using acoustic emissions

USGS Publications Warehouse

Cohen, D.; Hooyer, T.S.; Iverson, N.R.; Thomason, J.F.; Jackson, M.

2006-01-01

Probably the most important mechanism of glacial erosion is quarrying: the growth and coalescence of cracks in subglacial bedrock and dislodgement of resultant rock fragments. Although evidence indicates that erosion rates depend on sliding speed, rates of crack growth in bedrock may be enhanced by changing stresses on the bed caused by fluctuating basal water pressure in zones of ice-bed separation. To study quarrying in real time, a granite step, 12 cm high with a crack in its stoss surface, was installed at the bed of Engabreen, Norway. Acoustic emission sensors monitored crack growth events in the step as ice slid over it. Vertical stresses, water pressure, and cavity height in the lee of the step were also measured. Water was pumped to the lee of the step several times over 8 days. Pumping initially caused opening of a leeward cavity, which then closed after pumping was stopped and water pressure decreased. During cavity closure, acoustic emissions emanating mostly from the vicinity of the base of the crack in the step increased dramatically. With repeated pump tests this crack grew with time until the step's lee surface was quarried. Our experiments indicate that fluctuating water pressure caused stress thresholds required for crack growth to be exceeded. Natural basal water pressure fluctuations should also concentrate stresses on rock steps, increasing rates of crack growth. Stress changes on the bed due to water pressure fluctuations will increase in magnitude and duration with cavity size, which may help explain the effect of sliding speed on erosion rates. Copyright 2006 by the American Geophysical Union.

Extreme limestone weathering rates due to micron-scale grain detachment

NASA Astrophysics Data System (ADS)

Emmanuel, Simon; Levenson, Yael

2014-05-01

Chemical dissolution is often assumed to control the weathering rates of carbonate rocks, although some studies have indicated that mechanical erosion could also play a significant role. Quantifying the rates of the different processes is challenging due to the high degree of variability encountered in both field and lab settings. To measure the rates and mechanisms controlling long-term limestone weathering, we analyse a lidar scan of the Western Wall, a Roman period edifice located in Jerusalem. Surface retreat rates in fine-grained micritic limestone blocks are found to be as much as 2 orders of magnitude higher than the average rates estimated for coarse-grained limestone blocks at the same site. In addition, in experiments that use atomic force microscopy to image dissolving micritic limestone, we show that these elevated reaction rates could be due to rapid dissolution along micron-scale grain boundaries, followed by mechanical detachment of tiny particles from the surface. Our analysis indicates that micron-scale grain detachment, rather than pure chemical dissolution, could be the dominant erosional mode for fine-grained carbonate rocks.

Abandoned Mine Lands

EPA Pesticide Factsheets

Abandoned Mine Lands are those lands, waters, and surrounding watersheds where extraction, beneficiation, or processing of ores and minerals (excluding coal) has occurred. These lands also include areas where mining or processing activity is inactive.

Causes, outcome and prevention of abandonment in retinoblastoma in India.

PubMed

Kumar, Archana; Moulik, Nirmalya Roy; Mishra, Ravi Krishna; Kumar, Dipak

2013-05-01

The high-cure rates of 90% in retinoblastoma are not replicated in developing countries due to late presentation and poor compliance to treatment. The present study takes a closer look at causes of abandonment of therapy and effectiveness of counselling in reducing abandonment. A retrospective study of children with retinoblastoma registered at our centre from March 2008 through August 2011. Fifty (49.50%) of 101 children registered for treatment abandoned therapy. Abandonment rates were significantly higher in rural as compared to urban children (P = 0.02). There was no significant difference in rate of abandonment between stages or laterality of disease and other socio-demographic factors. Telephone calls were more effective than letters in tracing patients (31.2% vs. 2.4%). Major reasons cited behind abandonment were financial problems (30%) and unwillingness to enucleate (20%). Of the 12 children who returned and were retreated 6 (50%) died of progressive disease. Nineteen (73%) of those who did not return died at home. Abandonment rates steadily declined from 71.42% in 2008 to 16.66% in 2011 (P = 0.01) due to effective pre-abandonment counselling by a support team under the National Retinoblastoma Registry of India from 2009. Abandonment rates for children with retinoblastoma continue to be unacceptably high. Rural background, financial constraints and hesitancy to enucleate were important causes behind abandonment. Outcome of patients who abandoned treatment was uniformly dismal. Inclusion of support team and intensified initial counselling helped in improving compliance. Copyright © 2013 Wiley Periodicals, Inc.

Natural versus anthropogenic genesis of mardels (closed depressions) on the Gutland plateau (Luxembourg); archaeometrical and palynological evidence of Roman clay excavation from mardels.

NASA Astrophysics Data System (ADS)

van Mourik, Jan; Braekmans, Dennis; Doorenbosch, Marieke; Kuijper, Wim; van der Plicht, Hans

2016-04-01

Mardels, small closed depressions, are distinctive landforms on the Luxembourger Gutland plateau. In the present landscape most mardels are shallow fens, filled with colluvial sediments. The genesis of mardels has been studied intensively, inside and outside Luxembourg. Some researchers suggested a natural development and consider mardels as subsidence basins due to subsurface solution of gypsum veins, other researchers suggested cultural causes and consider mardels as prehistorical quarries. In the Gutland, mardels occur on various substrates. Mardels on the Strassen marls (li3) are abandoned quarries, related to clay excavation in Roman Time. Mardels on the Luxembourger sandstone (li2) are sinkholes, related to joint patterns in the sandstone formation. Mardels on the Keuper marls (km1,3) are originally subsidence basins, related to subsurface dissolutions of gypsum lenses and veins, filled with colluvial clay. The results of pollen analysis and archaeometrical tests demonstrate Roman extraction of clay for the production of ancient ceramics. So, the natural depressions have been enlarged to the present mardels. After excavation, the sedimentation of colluvium restarted in the abandoned quarries.

Western Abandoned Uranium Mine Region Fact Sheets

EPA Pesticide Factsheets

Fact sheets related to Western Abandoned Uranium Mine (AUM) Region, more than 100 abandoned uranium mine claims located along the Little Colorado River and Highway 89, ain the Cameron, Coalmine Canyon, Bodaway/Gap, and Leupp Chapters in Northern Arizona.

The USGS Abandoned Mine Lands Initiative: Protecting and restoring the environment near abandoned mine lands

USGS Publications Warehouse

,

1999-01-01

The Abandoned Mine Lands (AML) Initiative is part of a larger strategy of the U.S. Department of the Interior and the U.S. Department of Agriculture to clean up Federal lands contaminated by abandoned mines.Thousands of abandond hard-rock metal mines (such as gold, copper, lead, and zinc) have left a dual legacy across the Western United States. They reflect the historic development of the west, yet at the same time represent a possible threat to human health and local ecosystems.Abandoned Mine Lands (AML) are areas adjacent to or affected by abandoned mines. AML's often contain unmined mineral deposits, mine dumps (the ore and rock removed to get to the ore deposits), and tailings (the material left over from the ore processing) that contaminate the surrounding watershed and ecosystem. For example, streams near AML's can contain metals and (or) be so acidic that fish and aquatic insects cannot live in them.Many of these abandoned hard-rock mines are located on or adjacent to public lands administered by the Bureau of Land Management, National Park Service, and U.S. Forest Service. These federal land management agencies and the USGS are committed to mitigating the adverse effects that AML's can have on water quality and stream habitats.The USGS AML Initiative began in 1997 and will continue through 2001 in two pilot watersheds - the Boulder River basin in southwestern Montana and the upper Animas River basin in southwestern Colorado. The USGS is providing a wide range of scientific expertise to help land managers minimize and, where possible, eliminate the adverse environmental effects of AML's. USGS ecologists, geologists, water quality experts, hydrologists, geochemists, and mapping and digital data collection experts are collaborating to provide the scientific knowledge needed for an effective cleanup of AML's.

0-6686 : improving DMS 9210 requirements for limestone rock asphalt : [project summary].

DOT National Transportation Integrated Search

2013-08-01

Limestone rock asphalt (LRA) mixtures have : been produced and placed for several decades : using specification requirements currently listed : under DMS 9210, Limestone Rock Asphalt (LRA). : Several Texas Department of Transportation : (TxDOT) distr...

Syntectic Reactions involving Limestones and Limestone-Derived Carbonatitic Melts in the Generation of some Peralkalic Magmas: Reflections on Reginald Daly's Insights 100 Years Later

NASA Astrophysics Data System (ADS)

Lentz, D.

2017-12-01

The theoretical analysis of how sedimentary limestones and marbles could melt as a result of infiltrative contact metasomatism associated with silicate magmas, enables reconsideration of the limestone syntectic (assimilation) hypothesis for the origin of some peralkalic rocks. Reginald Daly's syntectic model published in detail in early 1918 fell out of favor because experimental evidence from the early 1960's suggested; 1) that limestone assimilation would increase P(CO2) and cause solidification of the silicate intrusion, 2) that there is a thermal barrier between silica-saturated and undersaturated magmas that would inhibit extensive desilication of the magma, and 3) the endothermic decarbonation reactions would require heat via magmatic crystallization of near-solidus magmas. However, these concerns were not as critical for high-T mafic melts relative to more low-T silicic melts, although most subsequent researchers dismissed syntexis as isotopic arguments also seemed robust. However, skarn-related limestone melts can interact much more easily with silicate magma, resulting in calc-silicate-forming (endoskarn-like) limestone syntectic (desilication - calcification-magnesification processes) decarbonation reactions with compositional evolution into the silica-undersaturated field. If mafic in composition originally when syntectically modified, then the CO2-bearing derivative peralkalic melt may subsequently react with the dominant volume magma or fractionate separately into a more evolved composition. As well, an increase in P(CO2) within the modified silicate fraction coupled with compositional evolution to more silica-undersaturated compositions enhances the stability of the immiscible, extremely low viscosity carbonate melt fraction. In addition, dynamic interaction of these co-existing immiscible melts (analogous to the current hypothesis) would partition elements, as well as isotopic signatures, such that they would be virtually unrecognizable as having a

Development of gypsum alteration on marble and limestone

USGS Publications Warehouse

McGee, E.S.

1996-01-01

Blackened alteration crusts of gypsum plus particulates that form on sheltered areas on marble and limestone buildings pose a challenge for rehabilitation and cleaning. Fresh marble and limestone samples exposed at monitored exposure sites present conditions of simple geometry and well-documented exposures but have short exposure histories (one to five years). The gypsum alteration crusts that develop on these samples provide insight into the early stages and rate of alteration crust formation. Alteration crusts from buildings give a longer, but less well known exposure history and present much more complex surfaces for gypsum accumulation. Integrated observations and measurements of alteration crusts from exposure samples and from buildings identify four factors that are important in the formation and development of alteration crusts on marble and limestone: (1) pollution levels, (2) exposure to rain or washing, (3) geometry of exposure of the stone surface, and (4) permeability of the stone. The combination of these factors contributes to both the distribution and the physical characteristics of the gypsum crusts which may affect cleaning decisions.

Fragmentation, Cost and Environmental Effects of Plaster Stemming Method for Blasting at A Basalt Quarry

NASA Astrophysics Data System (ADS)

Cevizci, Halim

2014-10-01

In this study, the plaster stemming application for blasting at a basalt quarry is studied. Drill cuttings are generally used in open pits and quarries as the most common stemming material since these are most readily available at blast sites. However, dry drill cuttings eject very easily from blastholes without offering much resistance to blast energy. The plaster stemming method has been found to be better than the drill cuttings stemming method due to increased confinement inside the hole and better utilization of blast explosive energy in the rock. The main advantage of the new stemming method is the reduction in the cost of blasting. At a basalt quarry, blasting costs per unit volume of rock were reduced to 15% by increasing burden and spacing distances. In addition, better fragmentation was obtained by using the plaster stemming method. Blast trials showed that plaster stemming produced finer material. In the same blast tests, +30 cm size fragments were reduced to 47.3% of the total, compared to 32.6% in the conventional method of drill cuttings stemming. With this method of stemming, vibration and air shock values increased slightly due to more blast energy being available for rock breakage but generally these increased values were small and stayed under the permitted limit for blast damage criteria unless measuring distance is too close.

39 CFR 946.11 - Disposition of property declared abandoned.

Code of Federal Regulations, 2010 CFR

2010-07-01

... DISPOSITION OF STOLEN MAIL MATTER AND PROPERTY ACQUIRED BY THE POSTAL INSPECTION SERVICE FOR USE AS EVIDENCE § 946.11 Disposition of property declared abandoned. Property declared abandoned, including cash, and... 39 Postal Service 1 2010-07-01 2010-07-01 false Disposition of property declared abandoned. 946.11...

39 CFR 946.11 - Disposition of property declared abandoned.

Code of Federal Regulations, 2011 CFR

2011-07-01

... DISPOSITION OF STOLEN MAIL MATTER AND PROPERTY ACQUIRED BY THE POSTAL INSPECTION SERVICE FOR USE AS EVIDENCE § 946.11 Disposition of property declared abandoned. Property declared abandoned, including cash, and... 39 Postal Service 1 2011-07-01 2011-07-01 false Disposition of property declared abandoned. 946.11...

Flue gas desulfurization chemistry studies: limestone grindability. Volume 2. Grindability testing. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richmann, D.L.; Luke, K.W.; Terry, J.C.

1984-07-01

The results of a study to determine the relative grindability of US limestones and to relate grindability to petrographic properties are presented in this report. A laboratory ball mill test was developed to provide a quick and simple measure of grindability. These values were then used to explore possible correlations between grindability and the chemical and physical properties of the limestones. Chemical analyses and thin section petrographic analyses were used to characterize the limestone samples. The results of the laboratory ball mill test were compared to the results of an industrial grinding test, the Bond Work Index, for six samplesmore » which covered the grindability range. The two tests compared well with a correlation coefficient greater than 0.9. While the laboratory test is not sufficient to provide ball mill design specifications, it can be used as a screening and quality control test. The grinding results, expressed as a grindability index, ranged in values from 2 to 15. This represents a seven-fold range in the relative difficulties to grind for the limestones tested. From the petrographic analysis results, a strong correlation was found between the grindability and the fraction of macrocrystalline (> 5 ..mu..m) carbonate minerals present in the limestone. However, based on the high degree of variability characteristic of most limestone deposits, petrographic information should, in general, only be used to qualitatively predict the grindability of a specific limestone. An actual grinding test is recommended for a quantitative evaluation.« less

STREAM INJECTION INTO FRACTURE BEDROCK AT LORING AFB

EPA Science Inventory

The Quarry at the former Loring Air Force Base in Limestone, Maine, was used for the disposal of drums containing spent chlorinated solvents, mainly tetrachloroethene (PCE). After closure of the base, surface geophysics were used to locate the drums, and they were removed. Subs...

46 CFR 131.530 - Abandon-ship training and drills.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Abandon-ship training and drills. 131.530 Section 131... OPERATIONS Tests, Drills, and Inspections § 131.530 Abandon-ship training and drills. (a) Material for... rescue gear (slings, baskets, stretchers) and vessel's line-throwing apparatus. (b) An abandon-ship drill...

46 CFR 131.530 - Abandon-ship training and drills.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Abandon-ship training and drills. 131.530 Section 131... OPERATIONS Tests, Drills, and Inspections § 131.530 Abandon-ship training and drills. (a) Material for... rescue gear (slings, baskets, stretchers) and vessel's line-throwing apparatus. (b) An abandon-ship drill...

46 CFR 131.530 - Abandon-ship training and drills.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Abandon-ship training and drills. 131.530 Section 131... OPERATIONS Tests, Drills, and Inspections § 131.530 Abandon-ship training and drills. (a) Material for... rescue gear (slings, baskets, stretchers) and vessel's line-throwing apparatus. (b) An abandon-ship drill...

Durability assessment of limestone subjected to surface treatments

NASA Astrophysics Data System (ADS)

Theodoridou, Magdalini; Charalambous, Cleopatra; Ioannou, Ioannis

2017-04-01

Weathering is inevitable in existing limestone structures due to their exposure to fluctuating and aggressive environmental conditions, such as wetting/drying, and the presence of salts. Therefore, conservation treatments are often deemed necessary in order to prevent or at least delay the progress of deterioration and to strengthen weathered stones. This paper focuses on the effect of an ethanol-based laboratory produced water repellent and three water-based commercial products (water repellent, pure acrylic emulsion mixed with a water repellent with thermal insulation properties and consolidant) on the durability and other properties of three different types of limestone (massive chalk, calcarenite and bioclastic limestone). All test specimens were subjected to micro-destructive cutting tests before/after the application of the aforementioned surface treatments to investigate changes in resistance to cutting on the area close to the treated surface. They were also subjected to two cycles of salt contamination with 20% w/w Na2SO4•10H2O solution by capillary absorption through their bottom face, until 2 mm of pore space was theoretically filled with salt crystals. Drying after salt contamination took place at 70 °C. The results of the micro-destructive cutting tests showed increases in cutting resistance at the topmost area (1-2 mm below the treated surface) of the massive chalk and the calcarenite, but no significant changes in the case of the rather non-homogeneous bioclastic limestone. At the same time, the performance of each surface treatment varied from lithotype to lithotype. The laboratory produced water repellent showed a generally better performance; no signs of damage were detected due to the formation of salt crystals within the pores of the materials, i.e. subflorescence, when applied on the calcarenite and the bioclastic limestone. Very poor performance was observed for all treatments when applied on the massive chalk. This accounted for (i

U-series dating of the Late Pleistocene mammalian fauna from Wood Quarry (Steetley), Nottinghamshire, UK

NASA Astrophysics Data System (ADS)

Pike, A. W. G.; Eggins, S.; Grün, R.; Hedges, R. E. M.; Jacobi, R. M.

2005-01-01

We present the U-series dating of bones from Wood Quarry (Steetley Quarry Cave) using the diffusion-adsorption model to account for uranium uptake. The results give a weighted mean date of 66.8 ± 3.0 kyr, placing this assemblage within or just before Marine Oxygen Isotope Stage 4. The fauna is thought to correlate with the Banwell Bone Cave mammal assemblage-zone of the Early Devensian in Britain. Our results support the idea that this assemblage-zone immediately precedes the assemblage represented nearby at Pin Hole in Creswell Crags which is contemporary with the Mid-Devensian and correlates with MIS 3. Our dates, and dates for the Banwell Bone Cave mammal assemblage-zone from Stump Cross Cavern and evidence from other sites may indicate a longevity for this fauna.

Mining (except Oil and Gas) Sector (NAICS 212)

EPA Pesticide Factsheets

EPA Regulatory and enforcement information for the mining sector, including metal mining & nonmetallic mineral mining and quarrying. Includes information about asbestos, coal mining, mountaintop mining, Clean Water Act section 404, and abandoned mine lands

Long-range laser scanning and 3D imaging for the Gneiss quarries survey

NASA Astrophysics Data System (ADS)

Schenker, Filippo Luca; Spataro, Alessio; Pozzoni, Maurizio; Ambrosi, Christian; Cannata, Massimiliano; Günther, Felix; Corboud, Federico

2016-04-01

In Canton Ticino (Southern Switzerland), the exploitation of natural stone, mostly gneisses, is an important activity of valley's economies. Nowadays, these economic activities are menaced by (i) the exploitation costs related to geological phenomena such as fractures, faults and heterogeneous rocks that hinder the processing of the stone product, (ii) continuously changing demand because of the evolving natural stone fashion and (iii) increasing administrative limits and rules acting to protect the environment. Therefore, the sustainable development of the sector for the next decades needs new and effective strategies to regulate and plan the quarries. A fundamental step in this process is the building of a 3D geological model of the quarries to constrain the volume of commercial natural stone and the volume of waste. In this context, we conducted Terrestrial Laser Scanning surveys of the quarries in the Maggia Valley to obtain a detailed 3D topography onto which the geological units were mapped. The topographic 3D model was obtained with a long-range laser scanning Riegl VZ4000 that can measure from up to 4 km of distance with a speed of 147,000 points per second. It operates with the new V-line technology, which defines the surface relief by sensing differentiated signals (echoes), even in the presence of obstacles such as vegetation. Depending on the esthetics of the gneisses, we defined seven types of natural stones that, together with faults and joints, were mapped onto the 3D models of the exploitation sites. According to the orientation of the geological limits and structures, we projected the different rock units and fractures into the excavation front. This way, we obtained a 3D geological model from which we can quantitatively estimate the volume of the seven different natural stones (with different commercial value) and waste (with low commercial value). To verify the 3D geological models and to quantify exploited rock and waste volumes the same

Characterization of microbial structures in Setul Limestone

NASA Astrophysics Data System (ADS)

Ezanie, A. S. Mohamad; Aziz, A. Che; Roslan, M. Kamal

2018-04-01

Setul Limestone in Langgun Island and Perlis are lack of sedimentary structures, which makes it difficult for paleoenvironmental study in the study area. The present study of limestone succession at Kaki Bukit and Teluk Mempelam area focuses on microbial related structure in order to constraint its depositional setting. The structures were identified as stromatolites and thrombolites, which resulted from the interaction of microbial with sediments by trapping, binding and/or precipitation of minerals. Both structures can be distinguished based on four main classifications, the megastructure, macrostructure, mesostructure and microstructure scales. These classifications assist in understanding its physical natures and lead to the recognition of paleoenvironment in the study area which is believed to be controlled by several factors such as environment, hydrodynamic, biological and chemical processes.

46 CFR 131.530 - Abandon-ship training and drills.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Abandon-ship training and drills. 131.530 Section 131... OPERATIONS Tests, Drills, and Inspections § 131.530 Abandon-ship training and drills. (a) Material for abandon-ship training must be aboard each vessel. The material must consist of a manual of one or more...

32 CFR 1618.1 - Abandonment of rights or privileges.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Abandonment of rights or privileges. 1618.1... NOTICE TO REGISTRANTS § 1618.1 Abandonment of rights or privileges. If a registrant fails to claim and exercise any right or privilege within the required time, he shall be deemed to have abandoned the right or...

Infanticide and illegal infant abandonment in Malaysia.

PubMed

Razali, Salmi; Kirkman, Maggie; Ahmad, S Hassan; Fisher, Jane

2014-10-01

Infant abandonment and infanticide are poorly understood in Malaysia. The information available in the public arena comes predominantly from anecdotal sources. The aim of this study was to describe the prevalence and characteristics of infanticide and illegal infant abandonment in Malaysia and to estimate annual rates for the most recent decade. Summaries of data about infanticide and illegal infant abandonment were gathered from police records; the annual number of live births was ascertained from the national registry. The estimated inferred infanticide rates for Malaysia were compared with the infanticide rates among countries of very high, high, medium, and low rankings on the Human Development, Gender Inequality, and Gini indices. From 1999 to 2011, 1,069 cases of illegal infant abandonment were recorded and 1,147 people were arrested as suspected perpetrators. The estimated inferred infanticide rate fluctuated between 4.82 and 9.11 per 100,000 live births, a moderate rate relative to the infanticide rates of other countries. There are substantial missing data, with details undocumented for about 78-87% of cases and suspected perpetrators. Of the documented cases, it appeared that more boys than girls were victims and that suspected perpetrators were predominantly Malays who were women, usually mothers of the victim; the possibility of arrest bias must be acknowledged. Economic and social inequality, particularly gender inequality, might contribute to the phenomena of infanticide and abandonment. Strategies to reduce rates of infanticide and illegal infant abandonment in Malaysia will require strengthening of the surveillance system and attention to the gender-based inequalities that underpin human development. Copyright © 2014 Elsevier Ltd. All rights reserved.

Product layer development during sulfation and sulfidation of uncalcined limestone particles at elevated pressures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zevenhoven, C.A.P.; Yrjas, K.P.; Hupa, M.M.

1998-07-01

Fluidized bed combustion or gasification allows for in-bed sulfur capture with a calcium-based sorbent such as limestone or dolomite. Sorbent particle size, porosity, internal surface, and their variation during conversion have great influence on the conversion of the sorbent. The uptake of SO{sub 2} and H{sub 2}S by five physically different limestones is discussed, for typical pressurized fluidized bed combustor or gasifier conditions: 850/950 C, 15/20 bar. Tests were done in a pressurized thermogravimetric apparatus (P-TGA), the size of the limestone particles was 250--300 {micro}m. It is stressed that the limestones remain uncalcined. A changing internal structure (CIS) model ismore » presented in which reaction kinetics and product layer diffusion are related to the intraparticle surface of reaction, instead of the outer particle surface as in unreacted shrinking core (USC)-type models. The random pore model was used for describing the changing internal pore and reaction surfaces. Rate parameters were extracted for all five limestones using the CIS model and a USC model with variable effective diffusivity. Differences in the sulfur capture performance of the limestones were evaluated. Plots of the CaSO{sub 4} or CaS product layer thickness as a function of conversion are given, and the relative importance of limestone porosity and internal surface is discussed.« less

Improvement in treatment abandonment in pediatric patients with cancer in Guatemala.

PubMed

Alvarez, Elysia; Seppa, Midori; Rivas, Silvia; Fuentes, Lucia; Valverde, Patricia; Antillón-Klussmann, Federico; Castellanos, Mauricio; Sweet-Cordero, E Alejandro; Messacar, Kevin; Kurap, John; Bustamante, Marisol; Howard, Scott C; Efron, Bradley; Luna-Fineman, Sandra

2017-10-01

Treatment refusal and abandonment are major causes of treatment failure for children with cancer in low- and middle-income countries (LMICs), like Guatemala. This study identified risk factors for and described the intervention that decreased abandonment. This was a retrospective study of Guatemalan children (0-18 years) with cancer treated at the Unidad Nacional de Oncología Pediátrica (UNOP), 2001-2008, using the Pediatric Oncology Network Database. Treatment refusal was a failure to begin treatment and treatment abandonment was a lapse of 4 weeks or longer in treatment. The impact of medicina integral, a multidisciplinary psychosocial intervention team at UNOP was evaluated. Cox proportional hazards analysis identified the effect of demographic and clinical factors on abandonment. Kaplan-Meier analysis estimated the survival. Of 1,789 patients, 21% refused or abandoned treatment. Abandonment decreased from 27% in 2001 to 7% in 2008 following the implementation of medicina integral. Factors associated with increased risk of refusal and abandonment: greater distance to the centre (P < 0.001), younger age (P = 0.017) and earlier year of diagnosis (P < 0.001). Indigenous race/ethnicity (P = 0.002) was associated with increased risk of abandonment alone. Abandonment correlated with decreased overall survival: 0.57 ± 0.02 (survival ± standard error) for those who completed therapy versus 0.06 ± 0.02 for those who abandoned treatment (P < 0.001) at 8.3 years. This study identified distance, age, year of diagnosis and indigenous race/ethnicity as risk factors for abandonment. A multidisciplinary intervention reduced abandonment and can be replicated in other LMICs. © 2017 Wiley Periodicals, Inc.

Use of borehole radar reflection logging to monitor steam-enhanced remediation in fractured limestone-results of numerical modelling and a field experiment

USGS Publications Warehouse

Gregoire, C.; Joesten, P.K.; Lane, J.W.

2006-01-01

Ground penetrating radar is an efficient geophysical method for the detection and location of fractures and fracture zones in electrically resistive rocks. In this study, the use of down-hole (borehole) radar reflection logs to monitor the injection of steam in fractured rocks was tested as part of a field-scale, steam-enhanced remediation pilot study conducted at a fractured limestone quarry contaminated with chlorinated hydrocarbons at the former Loring Air Force Base, Limestone, Maine, USA. In support of the pilot study, borehole radar reflection logs were collected three times (before, during, and near the end of steam injection) using broadband 100 MHz electric dipole antennas. Numerical modelling was performed to predict the effect of heating on radar-frequency electromagnetic (EM) wave velocity, attenuation, and fracture reflectivity. The modelling results indicate that EM wave velocity and attenuation change substantially if heating increases the electrical conductivity of the limestone matrix. Furthermore, the net effect of heat-induced variations in fracture-fluid dielectric properties on average medium velocity is insignificant because the expected total fracture porosity is low. In contrast, changes in fracture fluid electrical conductivity can have a significant effect on EM wave attenuation and fracture reflectivity. Total replacement of water by steam in a fracture decreases fracture reflectivity of a factor of 10 and induces a change in reflected wave polarity. Based on the numerical modelling results, a reflection amplitude analysis method was developed to delineate fractures where steam has displaced water. Radar reflection logs collected during the three acquisition periods were analysed in the frequency domain to determine if steam had replaced water in the fractures (after normalizing the logs to compensate for differences in antenna performance between logging runs). Analysis of the radar reflection logs from a borehole where the temperature

Accelerated weathering of limestone for CO2 mitigation opportunities for the stone and cement industries

USGS Publications Warehouse

Langer, W.H.; Juan, C.A.S.; Rau, G.H.; Caldeira, K.

2009-01-01

Large amounts of limestone fines coproduced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO 2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point-sources such as cement manufacturing. AWL reactants are readily available, inexpensive, and environmentally benign. Waste CO 2 is hydrated with water to produce carbonic acid, which then reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities within about 10 km of the coastline. The majority of U.S. coastal power generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufactures, and research scientists.

Structure of the top of the Karnak Limestone Member (Ste. Genevieve) in Illinois

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bristol, H.M.; Howard, R.H.

1976-01-01

To facilitate petroleum exploration in Illinois, the Illinois State Geological Survey presents a structure map (for most of southern Illinois) of the Karnak Limestone Member--a relatively pure persistent limestone unit (generally 10 to 35 ft thick) in the Ste. Genevieve Limestone of Genevievian age. All available electric logs and selected studies of well cuttings were used in constructing the map. Oil and gas development maps containing Karnak-structure contours are on open file at the ISGS.

Sedimentology and diagenesis of Miocene Lirio Limestone, Isla de Mona, Puerto Rico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruiz, H.; Gonzalez, L.A.; Budd, A.F.

1991-03-01

Isla de Mona is a carbonate plateau, 50 mi west of Puerto Rico. The island lies on the southern portion of the Mona Platform. It is composed mostly of two Miocene carbonate units: Isla de Mona Dolomite overlain by Lirio Limestone. The Lirio Limestone was deposited on a sloping erosional surface over the Isla de Mona Dolomite. The Miocene Lirio Limestone consists mostly of backreef sands (packstones) with a reefal sequence (boundstones and grainstones) present in the southwestern portion of the island. The reefal sequence is made up mostly of Stylophora, Porites, and Millepora. Thin, discreet pockets of carbonate mud,more » rich in planktonic foraminifera and radiolarians and mixed with shallow benthic fauna/flora (foraminifera, echinoderms, red algae, and corals) interpreted as storm deposits, are found throughout the unit. An extensive reefal zone can be inferred to be present throughout the southwestern to southern portions of the Mona Platform. The Lirio Limestone is heavily karstified and is riddled with sinkholes on the plateau surfaces and caves around the periphery of the island. Caves are exposed around the periphery of the island, radiating from a depression in the central portions of the Lirio Limestone, near contacts with the Isla de Mona Dolomite, are partially dolomitized. The southwestern outcrops exhibit partial dolomitization throughout. The distribution of sinkholes, seaward caverns, and partial dolomitization of the lowermost Lirio Limestone suggests diagenetic modifications by meteoric fluids in central exposed portions of the island and by marine-meteoric fluids in the lowermost portions of the phreatic lens.« less

Study on the influence of the decoking agent on the activity of limestone in wet flue gas desulfurization

NASA Astrophysics Data System (ADS)

Li, Qianjun; Xu, Dongyang; Wu, Yunxia; Yu, Jin

2017-01-01

Influence of the main components of decoking agent (magnesium nitrate, aluminum nitrate, copper nitrate, ammonium nitrate and actual decoking agent) on the activity of limestone is studied in laboratory by MET method. Results show that magnesium nitrate, ammonium nitrate and copper nitrate almost has no effect on the activity of limestone. With the concentration increasing, aluminum nitrate has an increasing inhibition on the dissolution of limestone. Fly ash has inhibition on dissolution of limestone due to the blockage of limestone pore by fly ash. The actual decoking agent has almost no effect on the limestone.

Thermo-poroelastic response of an argillaceous limestone

NASA Astrophysics Data System (ADS)

Selvadurai, Patrick; Najari, Meysam

2016-04-01

Argillaceous limestones are now being considered by many countries that intend to develop deep geologic storage facilities for siting both high-level and intermediate- to low-level nuclear fuel wastes. In deep geologic settings for high level nuclear wastes, the heating due to radioactive decay is transmitted through an engineered barrier, which consists of the waste container and an engineered geologic barrier, which consists of an encapsulating compacted bentonite. The heat transfer process therefore leads to heating of the rock mass where the temperature of the rock is substantially lower than the surface temperature of the waste container. This permits the use of mathematical theories of poroelastic media where phase transformations, involving conversion of water to a vapour form are absent. While the thermo-poroelastic responses of geologic media such as granite and porous tuff have been investigated in the literature, the investigation of thermo-poroelastic responses of argillaceous limestones is relatively new. Argillaceous limestones are considered to be suitable candidates for siting deep geologic repositories owing to the ability to accommodate stress states with generation of severe defects that can influence their transmissivity characteristics. Also the clay fraction in such rocks can contribute to long term healing type phenomena, which is a considerable advantage. This research presents the results of a laboratory investigation and computational modelling of the same that examines the applicability of the theory of thermo-poroelasticity, which extend Biot's classical theory of poroelasticity to include uncoupled heat conduction. The experimental configuration involves the boundary heating of a cylinder of the Cobourg Limestone from southern Ontario, Canada. The cylinder measuring 150 mm in diameter and 278 mm in length contains an axisymmetric fluid-filled cylindrical cavity measuring 26 mm in diameter and 139 mm in length. Thermo-poroelastic effects

Evaluating performance of limestone prone to polishing.

DOT National Transportation Integrated Search

2009-12-01

This research project evaluated the effect of blending Vanport limestone and other aggregates on the frictional surface characteristic properties of constructed trial road surfaces. The study undertook the evaluation of the performance of different m...

Stratigraphy and depositional history of the West Franklin Limestone (Pennsylvanian) in the southernmost part of the Illinois Basin, western Kentucky

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, N.R.

1994-04-01

The West Franklin Limestone in the subsurface of Webster and Union Counties, Kentucky includes 7.5--18m of strata deposited during portions of four depositional cycles in the latest Desmoinesian and earliest Missourian (Pennsylvanian). These cycles began with marine flooding and deposition of limestone, followed by progradation of siliciclastics in three of the four cycles, and ended with emergence. The basal West Franklin is micritic limestone (0.5--3m) that rests on rooted mudstone. Overlying the limestone are siliciclastics (1.5--7m) dominated by red and green claystone that is rooted at the top. Next is a middle limestone zone that includes either a paleokarsted micriticmore » limestone, or a thin bioclastic micritic limestone bed associated with phosphatic shale and locally a second bioclastic micritic limestone. Above that is another siliciclastic interval (4--9m) capped by rooted mudstone and locally a thin coal. The overlying micritic limestone (1.5--2.5m) marks the top of the West Franklin. Depositional events included: (1) marine flooding of an emergent shelf producing the basal limestone; (2) progradation of siliciclastics followed by emergence and paleosol development; (3) marine flooding producing a second limestone; (4) emergence and karstification of erosional remnants of the second limestone; (5) renewed marine flooding depositing shell hash'' limestones and phosphatic shale; (6) progradation of siliciclastics culminating in emergency; and (7) marine flooding producing the upper limestone. Thus, two flooding-emergence cycles are represented by the middle limestone zone. The second, locally-developed shell-hash'' limestone in the middle zone was deposited during the regressive phase of a depositional cycle. All of the other limestones were deposited during transgression.« less

21 CFR 1315.27 - Abandonment of quota.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 9 2013-04-01 2013-04-01 false Abandonment of quota. 1315.27 Section 1315.27 Food... may at any time abandon his right to manufacture all or any part of the quota by filing with the Drug... to manufacture. The Administrator may, in his discretion, allocate the amount among the other...

21 CFR 1315.27 - Abandonment of quota.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 9 2012-04-01 2012-04-01 false Abandonment of quota. 1315.27 Section 1315.27 Food... may at any time abandon his right to manufacture all or any part of the quota by filing with the Drug... to manufacture. The Administrator may, in his discretion, allocate the amount among the other...

21 CFR 1315.27 - Abandonment of quota.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Abandonment of quota. 1315.27 Section 1315.27 Food... may at any time abandon his right to manufacture all or any part of the quota by filing with the Drug... to manufacture. The Administrator may, in his discretion, allocate the amount among the other...

21 CFR 1315.27 - Abandonment of quota.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 9 2014-04-01 2014-04-01 false Abandonment of quota. 1315.27 Section 1315.27 Food... may at any time abandon his right to manufacture all or any part of the quota by filing with the Drug... to manufacture. The Administrator may, in his discretion, allocate the amount among the other...

21 CFR 1315.27 - Abandonment of quota.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 9 2011-04-01 2011-04-01 false Abandonment of quota. 1315.27 Section 1315.27 Food... may at any time abandon his right to manufacture all or any part of the quota by filing with the Drug... to manufacture. The Administrator may, in his discretion, allocate the amount among the other...

43 CFR 3162.3-4 - Well abandonment.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Well abandonment. 3162.3-4 Section 3162.3... Operating Rights Owners and Operators § 3162.3-4 Well abandonment. (a) The operator shall promptly plug and... newly completed or recompleted well in which oil or gas is not encountered in paying quantities or which...

43 CFR 3162.3-4 - Well abandonment.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Well abandonment. 3162.3-4 Section 3162.3... Operating Rights Owners and Operators § 3162.3-4 Well abandonment. (a) The operator shall promptly plug and... newly completed or recompleted well in which oil or gas is not encountered in paying quantities or which...

43 CFR 3162.3-4 - Well abandonment.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Well abandonment. 3162.3-4 Section 3162.3... Operating Rights Owners and Operators § 3162.3-4 Well abandonment. (a) The operator shall promptly plug and... newly completed or recompleted well in which oil or gas is not encountered in paying quantities or which...

43 CFR 3162.3-4 - Well abandonment.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Well abandonment. 3162.3-4 Section 3162.3... Operating Rights Owners and Operators § 3162.3-4 Well abandonment. (a) The operator shall promptly plug and... newly completed or recompleted well in which oil or gas is not encountered in paying quantities or which...

40 CFR 52.2276 - Control strategy and regulations: Particulate matter.

Code of Federal Regulations, 2010 CFR

2010-07-01

... its limestone quarry facilities near New Braunfels, Comal County, Texas shall install fabric filters... of the fabric filters, Parker Brothers and Co., Inc., shall not emit particulate matter in excess of 0.03 grains per standard cubic foot from the exhaust stack of the fabric filter on its primary...

40 CFR 52.2276 - Control strategy and regulations: Particulate matter.

Code of Federal Regulations, 2013 CFR

2013-07-01

... its limestone quarry facilities near New Braunfels, Comal County, Texas shall install fabric filters... of the fabric filters, Parker Brothers and Co., Inc., shall not emit particulate matter in excess of 0.03 grains per standard cubic foot from the exhaust stack of the fabric filter on its primary...

40 CFR 52.2276 - Control strategy and regulations: Particulate matter.

Code of Federal Regulations, 2012 CFR

2012-07-01

... its limestone quarry facilities near New Braunfels, Comal County, Texas shall install fabric filters... of the fabric filters, Parker Brothers and Co., Inc., shall not emit particulate matter in excess of 0.03 grains per standard cubic foot from the exhaust stack of the fabric filter on its primary...

19 CFR 19.9 - General order, abandoned, and seized merchandise.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 1 2011-04-01 2011-04-01 false General order, abandoned, and seized merchandise... Provisions § 19.9 General order, abandoned, and seized merchandise. (a) Acceptance of merchandise. The... storing. General order, abandoned, and seized goods and articles shall be recorded and stored in the...

19 CFR 19.9 - General order, abandoned, and seized merchandise.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false General order, abandoned, and seized merchandise... Provisions § 19.9 General order, abandoned, and seized merchandise. (a) Acceptance of merchandise. The... storing. General order, abandoned, and seized goods and articles shall be recorded and stored in the...

Selection of site specific vibration equation by using analytic hierarchy process in a quarry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalayci, Ulku, E-mail: ukalayci@istanbul.edu.tr; Ozer, Umit, E-mail: uozer@istanbul.edu.tr

This paper presents a new approach for the selection of the most accurate SSVA (Site Specific Vibration Attenuation) equation for blasting processes in a quarry located near settlements in Istanbul, Turkey. In this context, the SSVA equations obtained from the same study area in the literature were considered in terms of distance between the shot points and buildings and the amount of explosive charge. In this purpose, 11 different SSVA equations obtained from the study area in the past 12 years, forecasting capabilities according to designated new conditions, using 102 vibration records as test data obtained from the study areamore » was investigated. In this study, AHP (Analytic Hierarchy Process) was selected as an analysis method in order to determine the most accurate equation among 11 SSAV equations, and the parameters such as year, distance, charge, and r{sup 2} of the equations were used as criteria for AHP. Finally, the most appropriate equation was selected among the existing ones, and the process of selecting according to different target criteria was presented. Furthermore, it was noted that the forecasting results of the selected equation is more accurate than that formed using the test results. - Highlights: • The optimum Site Specific Vibration Attenuation equation for blasting in a quarry located near settlements was determined. • It is indicated that SSVA equations changing over the years don’t give always accurate estimates at changing conditions. • Selection of the blast induced SSVA equation was made using AHP. • Equation selection method was highlighted based on parameters such as charge, distance, and quarry geometry changes (year).« less

Dry and stable excavations in limestones of the greater Kansas City area of Missouri and Kansas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goebel, E.D.; Parizek, E.J.; Stauffer, T.P.

In the Greater Kansas City area of Missouri and Kansas the bedrock consists largely of a thick sequence of limestone and shale formations of Pennsylvanian age. Three formations are of interest in this report. The Swope Formation contains the Bethany Falls Limestone, the Wyandotte Formation contains the Argentine Limestone and the Farley Limestone, and the Oread Formation contains the Plattsmouth Limestone. Underground workings have been developed by industry in these three formations for a variety of uses, including factories, offices and warehouses. The Bethany Falls Limestone is the unit most widely developed for secondary underground use. The industries which design,more » excavate, and occupy this man-made underground space consider it to be essentially dry and stable. Identification and description of the geologic, topographic, hydrologic, and possible other unique features which allow this operational decision is the primary goal of this investigation.« less

Limestone and Silica Powder Replacements for Cement: Early-Age Performance.

PubMed

Bentz, Dale P; Ferraris, Chiara F; Jones, Scott Z; Lootens, Didier; Zunino, Franco

2017-04-01

Developing functional concrete mixtures with less ordinary portland cement (OPC) has been one of the key objectives of the 21 st century sustainability movement. While the supplies of many alternatives to OPC (such as fly ash or slag) may be limited, those of limestone and silica powders produced by crushing rocks seem virtually endless. The present study examines the chemical and physical influences of these powders on the rheology, hydration, and setting of cement-based materials via experiments and three-dimensional microstructural modeling. It is shown that both limestone and silica particle surfaces are active templates (sites) for the nucleation and growth of cement hydration products, while the limestone itself is also somewhat soluble, leading to the formation of carboaluminate hydration products. Because the filler particles are incorporated as active members of the percolated backbone that constitutes initial setting of a cement-based system, replacements of up to 50 % of the OPC by either of these powders on a volumetric basis have minimal impact on the initial setting time, and even a paste with only 5 % OPC and 95 % limestone powder by volume achieves initial set within 24 h. While their influence on setting is similar, the limestone and silica powders produce pastes with quite different rheological properties, when substituted at the same volume level. When proceeding from setting to later age strength development, one must also consider the dilution of the system due to cement removal, along with the solubility/reactivity of the filler. However, for applications where controlled (prompt) setting is more critical than developing high strengths, such as mortar tile adhesives, grouts, and renderings, significant levels of these powder replacements for cement can serve as sustainable, functional alternatives to the oft-employed 100 % OPC products.

Abandoned floodplain plant communities along a regulated dryland river

USGS Publications Warehouse

Reynolds, L. V.; Shafroth, Patrick B.; House, P. K.

2014-01-01

Rivers and their floodplains worldwide have changed dramatically over the last century because of regulation by dams, flow diversions and channel stabilization. Floodplains no longer inundated by river flows following dam-induced flood reduction comprise large areas of bottomland habitat, but the effects of abandonment on plant communities are not well understood. Using a hydraulic flow model, geomorphic mapping and field surveys, we addressed the following questions along the Bill Williams River, Arizona: (i) What per cent of the bottomland do abandoned floodplains comprise? and (ii) Are abandoned floodplains quantitatively different from adjacent xeric and riparian surfaces in terms of vegetation composition and surface sediment? We found that nearly 70% of active channel and floodplain area was abandoned following dam installation. Abandoned floodplains along the Bill Williams River tend to be similar to each other yet distinct from neighbouring habitats: they have been altered physically from their historic state, leading to distinct combinations of surface sediments, hydrology and plant communities. Abandoned floodplains may transition to xeric communities over time but are likely to retain some riparian qualities as long as there is access to relatively shallow ground water. With expected increases in water demand and drying climatic conditions in many regions, these surfaces and associated vegetation will continue to be extensive in riparian landscapes worldwide

Accelerated weathering of limestone for CO2 mitigation: Opportunities for the stone and cement industries

USGS Publications Warehouse

Langer, William H.; San, Juan A.; Rau, Greg H.; Caldeira, Ken

2009-01-01

Large amounts of limestone fines co-produced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point sources such as cement manufacturing. AWL reactants are readily available, inexpensive and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid. This reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate.

Fracture Decoupling of Small Chemical Explosions in Granite and Limestone

NASA Astrophysics Data System (ADS)

Stroujkova, A. F.; Bonner, J. L.; Reinke, R.; Lenox, E. A.

2012-12-01

Reduction of the seismic amplitudes produced by underground explosions due to dissipation in a low-coupling medium poses a significant challenge for nuclear test monitoring. We examined the data from two experiments, which involved conducting explosions in the damage zone created by previous explosions ("repeat shots"). The first experiment was conducted in central New Hampshire in a fluid saturated granodiorite. The experiment involved detonating two 46 kg explosions: one in virgin rock and the other in the fractured rock zone produced by a larger (232 kg) explosion. The second experiment took place near Albuquerque, NM, in dry limestone. In this scenario the second explosion was conducted in the cavity created by the first explosion. Both limestone explosions had yields of 90.5 kg. The reduction of the seismic amplitudes was observed for both repeat shots: in granodiorite the amplitudes were reduced by a factor of 2-3, in limestone by a factor of 3-4 compared to the shots in the undamaged rocks. For the granodiorite repeat shot the decoupling ratios were frequency dependent with stronger amplitude reduction at higher frequencies. In addition, the virgin rock shot produced higher corner frequency and overshoot parameter than the repeat shot. For the limestone shot the decoupling ratios were nearly flat at all frequencies with similar corner frequencies. This observation suggests different mechanisms of energy dissipation for the two experiments.

"The Giver" and "Shade's Children": Future Views of Child Abandonment and Murder.

ERIC Educational Resources Information Center

Gross, Melissa

1999-01-01

Examines reasons for child abandonment and murder and how it relates to abandonment in traditional literature. Considers new views of child abandonment and murder (focusing not on overcoming their abandonment, but changing and restructuring their entire society) presented in "The Giver" and "Shade's Children." Discusses the…

Localized Detection of Abandoned Luggage

NASA Astrophysics Data System (ADS)

Chang, Jing-Ying; Liao, Huei-Hung; Chen, Liang-Gee

2010-12-01

Abandoned luggage represents a potential threat to public safety. Identifying objects as luggage, identifying the owners of such objects, and identifying whether owners have left luggage behind are the three main problems requiring solution. This paper proposes two techniques which are "foreground-mask sampling" to detect luggage with arbitrary appearance and "selective tracking" to locate and to track owners based solely on looking only at the neighborhood of the luggage. Experimental results demonstrate that once an owner abandons luggage and leaves the scene, the alarm fires within few seconds. The average processing speed of the approach is 17.37 frames per second, which is sufficient for real world applications.

Heavy metal water pollution associated with the use of sewage sludge compost and limestone outcrop residue for soil restoration: effect of saline irrigation.

NASA Astrophysics Data System (ADS)

Pérez-Gimeno, Ana; Navarro-Pedreño, Jose; Gómez, Ignacio; Belén Almedro-Candel, María; Jordán, Manuel M.; Bech, Jaume

2015-04-01

The use of composted sewage sludge and limestone outcrop residue in soil restoration and technosol making can influence the mobility of heavy metals into groundwater. The use of compost from organic residues is a common practice in soil and land rehabilitation, technosol making, and quarry restoration (Jordán et al. 2008). Compost amendments may improve the physical, chemical, and biological properties of soils (Jordão et al. 2006; Iovieno et al. 2009). However, the use of compost and biosolids may have some negative effects on the environment (Karaca 2004; Navarro-Pedreño et al. 2004). This experiment analyzed the water pollution under an experimental design based on the use of columns (0-30 cm) formed by both wastes. Two waters of different quality (saline and non-saline) were used for irrigation. The presence of heavy metals (Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn) in the leachates was checked under controlled conditions inside a greenhouse (mean values: 20°±5°C and around 60% relative humidity). Sixteen 30-cm tall columns made of PVC pipe with internal diameters of 10.5 cm were prepared. The columns were filled with one of these materials: either sewage sludge compost (SW) or limestone outcrop residue (LR), fraction (<4 mm). The columns were irrigated with 2000 mL/week (230 mm) for twelve weeks (April to July). Half of them were irrigated with non-saline water (NS) and the others were so with saline water (S) from the beginning of the experiment. Four treatments combining the quality of the irrigation water (saline and non-saline) and wastes were studied: SW-NS, SW-S, LR-NS, and LR-S. After 24 hours of irrigation on the first day of each week, the leachates were taken and analyzed the heavy metal content (AAS-ES espectometer). The environmental risk due to the presence of heavy metals associated with the use of these materials was very low in general (under 0.1 mg/L). The use of sewage sludge favoured the presence of these metals in the lecheates and no effect

EXTERIOR VIEW, LOOKING EAST, OF REDUCTION PLANT NO. 6 WITH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

EXTERIOR VIEW, LOOKING EAST, OF REDUCTION PLANT NO. 6 WITH PRIMARY AND SECONDARY LIMESTONE REDUCTION ('CRUSHING') IN PROGRESS. FEEDER (RIGHT) FEEDS TO CONVEYOR BELTS (CENTER) AND CRUSHER (LEFT). LIMESTONE PROCESSED THROUGH THIS OPERATION IS FURTHER SCREENED AND PROCESSED AT ANOTHER PLANT ON THE THOMAS SITE. OPERATION OF THIS PLANT, WHICH BEGAN IN 1960, INCORPORATES WITHIN THE FEEDER A CONCRETE RETAINING WALL DATING TO A TURN OF THE CENTURY QUARRY OPERATION FORMERLY ON THIS SITE. - Wade Sand & Gravel Company, Reduction Plant No. 6, State Route 78, Thomas, Jefferson County, AL

AERIAL VIEW, LOOKING EAST TOWARD IRONDALE AND TRUSSVILLE, ALONG THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

AERIAL VIEW, LOOKING EAST TOWARD IRONDALE AND TRUSSVILLE, ALONG THE CREST OF RED (RUFFNER) MOUNTAIN WITH FORMER SLOSS LIMESTONE QUARRY (CENTER). JONES VALLEY AND CITY OF BIRMINGHAM IS TO THE LEFT, SHADES VALLEY TO THE RIGHT. - Ruffner Red Ore Mine, North of I-20 at Madrid Exit, Birmingham, Jefferson County, AL

Kerford Limestone Company - Clean Water Act Public Notice

EPA Pesticide Factsheets

The EPA is providing notice of a proposed Administrative Penalty Assessment against Kerford Limestone Company, for alleged violations at the facility located at 36111 Fletcher Avenue, Weeping Water NE 68463.

Performance of portland limestone cements : cements designed to be more sustainable that include up to 15% limestone addition.

DOT National Transportation Integrated Search

2013-11-01

In 2009, ASTM and AASHTO permitted the use of up to 5% interground limestone in ordinary portland cement (OPC) as a part of ASTM : C150/AASHTO M85. When this project was initiated a new proposal was being discussed that would enable up to 15% intergr...

Reducing the risk of the collapse of the soil by macro system modeling the slopes stability of the quarries

NASA Astrophysics Data System (ADS)

Klimova, E. V.; Semeykin, A. Yu

2018-01-01

The urgent task of modern production is to reduce the risks of man-made disasters and, as a consequence, preserve the life and health of workers, material properties and natural environment. In the mining industry, one of the reasons for the high level of injuries and accidents is the collapse of the soil. Macro system modelling of slopes stability of the quarries is based on the compliance with the conditions of physical and mathematical correctness of the application of the model of a continuous medium. This type of modelling allows to choose the safe parameters of the slopes of the quarries and to reduce the risk of collapse of the soil.

17 CFR 230.155 - Integration of abandoned offerings.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Integration of abandoned... GENERAL RULES AND REGULATIONS, SECURITIES ACT OF 1933 General § 230.155 Integration of abandoned offerings... from integration of private and registered offerings. Because of the objectives of Rule 155 and the...

Stone Quarrying, Crushing and Screening Facilities General Air Quality Permit Request for Coverage: US Silica - Parshall Transload Facility

EPA Pesticide Factsheets

Documents related to Request for Coverage under Stone Quarrying, Crushing, and Screening Facilities General Permit Indian Reservation, US Silica, Parshall Transload Facility, Fort Berthold Indian Reservation, North Dakota.

Hydrology of the cavernous limestones of the Mammoth Cave area, Kentucky

USGS Publications Warehouse

Brown, Richmond F.

1966-01-01

The Mammoth Cave National Park in central Kentucky offers a unique opportunity to study the occurrence of ground water in limestone under natural conditions. Ground water occurs as perched and semiperched bodies in alternate sandstone, shale, and limestone formations and under water-table conditions at the approximate level of the Green River in thick soluble limestone. Three continuous recorders that operated for 5 years indicate that precipitation on the Mammoth Cave plateau recharges the underlying sandstone rapidly. Ground water from the sandstone discharges horizontally to the edges of the plateau and vertically to underlying formations. Some of the precipitation recharges underlying formations almost immediately through overland flow to sinkholes and free fall through open shafts to pools at the water table. Much of the precipitation on the Pennyroyal plain flows overland into sinkholes and then through solution openings to the Green River. Water from the Green River flows into limestone solution channels under Mammoth Cave plateau at some stages, and this water discharges again to the Green River downstream. The presence of salt water, high in chloride in the Green River, makes it possible to trace the movement of the river water through the underground streams. Graphs show relationships of chloride concentration, stage of the Green River, time, precipitation, ground-water levels, and stratigraphy.

Well Abandonment at Various Sites, John F. Kennedy Space Center, Florida

NASA Technical Reports Server (NTRS)

Damphousse, Sarah Joan

2016-01-01

Between January 29 and March 9, 2016, a total of 23 monitoring wells were properly abandoned-in-place at five KSC sites (OPF-1&2, OPF-3, RDG, SRB, and HSB). The total abandonment encompassed 489.06 linear feet. The wells abandoned were constructed of PVC with diameters ranging from 1-inch to 2-inches. The shallowest well abandoned was measured to be 11.6 ft bls (OPF) and the deepest well abandoned was documented to be 51.45 feet bls (HSB). All aboveground completions were removed and each area was re-graded and/or grouted to surface to match existing surroundings. All materials (concrete pads, well casings, etc.) were disposed of accordingly.

The influence of additives on rheological properties of limestone slurry

NASA Astrophysics Data System (ADS)

Jaworska, B.; Bartosik, A.

2014-08-01

Limestone slurry appears in the lime production process as the result of rinsing the processed material. It consists of particles with diameter smaller than 2 mm and the water that is a carrier of solid fraction. Slurry is directed to the settling tank, where the solid phase sediments and the excess water through the transfer system is recovered for re-circulation. Collected at the bottom of the tank sludge is deposited in a landfill located on the premises. Rheological properties of limestone slurry hinder its further free transport in the pipeline due to generated flow resistance. To improve this state of affairs, chemical treatment of drilling fluid, could be applied, of which the main task is to give the slurry properties suitable for the conditions encountered in hydrotransport. This treatment consists of applying chemical additives to slurry in sufficient quantity. Such additives are called as deflocculants or thinners or dispersants, and are chemical compounds which added to aqueous solution are intended to push away suspended particles from each other. The paper presents the results of research allowing reduction of shear stress in limestone slurry. Results demonstrate rheological properties of limestone slurry with and without the addition of modified substances which causes decrease of slurry viscosity, and as a consequence slurry shear stress for adopted shear rate. Achieving the desired effects increases the degree of dispersion of the solid phase suspended in the carrier liquid and improving its ability to smooth flow with decreased friction.

12 CFR 563g.11 - Withdrawal or abandonment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Withdrawal or abandonment. 563g.11 Section 563g.11 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY SECURITIES OFFERINGS § 563g.11 Withdrawal or abandonment. (a) Any offering circular, amendment, or exhibit may be withdrawn...

Improvement of cement plant dust emission by bag filter system

NASA Astrophysics Data System (ADS)

Wahyu Purnomo, Chandra; Budhijanto, Wiratni; Alfisyah, Muziibu; Triyono

2018-03-01

The limestone quarry in PT Indocement Tunggal Prakarsa (ITP) in Cirebon is considered as a complex quarry in terms of chemical composition and material hardness. From the beginning of the plant operation up to the end of 2015, the dust removal was rely on electrostatic precipitator (EP) system. Whenever limestone from specific quarry zones were incorporated into Raw Mill (RM) feed or there was an upset condition, the dust emission increased significantly. Beside higher demand of electricity, an EP system requires lower gas inlet temperature in order to remove the dust effectively which requires larger cooling water in the previous gas conditioning tower to cool down gas from 400 °C to about 100 °C. By considering the drawbacks, the EP system was replaced by a bag filter (BF) system. The BF allows higher temperature of gas inlet and it has higher dust removal efficiency. In this study, the efficiency of the two different dust removal systems is compared. The effect of process variables i.e. RM feed, kiln feed, inlet temperature and pressure, and small size particle fraction to the dust emission are studied by multivariate linier regression analysis. It is observed that the BF system can reduce significantly the dust emission from 30 to 6 mg/m3 and in the same time reducing CO2 emission by 0.24 ton/year from the electricity consumption saving.

Hydrogeology of the gray limestone aquifer in southern Florida

USGS Publications Warehouse

Reese, Ronald S.; Cunningham, Kevin J.

2000-01-01

Results from 35 new test coreholes and aquifer-test, water-level, and water-quality data were combined with existing hydrogeologic data to define the extent, thickness, hydraulic properties, and degree of confinement of the gray limestone aquifer in southern Florida. This aquifer, previously known to be present only in southeastern Florida (Miami-Dade, Broward, and Palm Beach Counties) below, and to the west of, the Biscayne aquifer, extends over most of central-south Florida, including eastern and central Collier County and southern Hendry County; it is the same as the lower Tamiami aquifer to the north, and it becomes the water-table aquifer and the upper limestone part of the lower Tamiami aquifer to the west. The aquifer generally is composed of gray, shelly, lightly to moderately cemented limestone with abundant shell fragments or carbonate sand, abundant skeletal moldic porosity, and minor quartz sand. The gray limestone aquifer comprises the Ochopee Limestone of the Tamiami Formation, and, in some areas, the uppermost permeable part of an unnamed formation principally composed of quartz sand. Underlying the unnamed formation is the Peace River Formation of the upper Hawthorn Group, the top of which is the base of the surficial aquifer system. Overlying the aquifer and providing confinement in much of the area is the Pinecrest Sand Member of the Tamiami Formation. The thickness of the aquifer is comparatively uniform, generally ranging from 30 to 100 feet. The unnamed formation part of the aquifer is up to 20 feet thick. The Ochopee Limestone accumulated in a carbonate ramp depositional system and contains a heterozoan carbonate-particle association. The principal rock types of the aquifer are pelecypod lime rudstones and floatstones and permeable quartz sands and sandstones. The pore types are mainly intergrain and separate vug (skeletal-moldic) pore spaces. The rock fabric and associated primary and secondary pore spaces combine to form a dual diffuse

Influence of mineralogical, petrographical, and geochemical characteristics of impure limestones on the composition of fired hydraulic lime: a case study on Lower Palaeozoic limestones from the Prague Basin (Barrandian area, Czech Republic)

NASA Astrophysics Data System (ADS)

Kozlovcev, Petr; Přikryl, Richard

2014-05-01

Prague Basin, making part of the Barrandian area (Bohemian Massif, Czech Republic), is a rift-like depression filled with non-metamorphosed sedimentary series of Upper Proterozoic - Lower Palaeozoic age. Among other sedimentary rocks, different types of limestones are present. These limestone were historically exploited and used for various purposes including natural and decorative stone, common construction material, and also a raw material for firing of inorganic binders: aerial lime, hydraulic lime and/or, more recently, Ordinary Portland Cement (OPC). Lithotypes with higher amount of silica and/or clay component were of special interest due to the hydraulicity of fired product known as "pasta di Praga" in Baroque. However, our recent knowledge of these limestones is incomplete in terms of the contribution of mineralogical, geochemical, and petrographical characteristics on the properties of fired hydraulic lime. In the recent study, representative samples of 4 facies of the Lower Devonian limestone (Kosoř ls., Řeporyje ls., Dvorce-Prokop ls., and Zlíchov ls.) were subjected to a detailed mineralogical and petrographic study of raw material by means of polarizing microscopy, cathodoluminiscence of thin sections and scanning electron microscopy with an energy dispersive spectrometer (SEM-EDS). X-ray diffraction (XRD) of insoluble residues obtained by treatment with both the hydrochloric acid and the acetic acid solution was used. Wet silicate analysis provided data on the content of major elements from which standard cement and lime indexes and modules were calculated. Laboratory firing experiments of these limestone were performed by a calcination at temperature ranging from 850 to 1200°C (after 50°C). XRD of fired products shows that limestones with high content of silica (some of the Dvorce-Prokop ls.) produced binder with high amount of newly formed calcium silicates (larnite). Gehlenite and others calcium aluminates and aluminosilicates are typical for

Effect of limestone reactivity and percent on production by dairy cows in early lactation.

PubMed

Nocek, J E; Braund, D G; English, J E

1983-12-01

Seventy-two Holstein cows (16 first lactation) were assigned to four treatments: A) normal-grind limestone (800 to 1000 mu) added to provide .77% calcium (total ration dry basis); B) fine-grind limestone (less than 150 mu) at .77% calcium; C) normal-grind at 1.15% calcium; and D) fine-grind limestone at 1.15% calcium. Cows fed diets containing .77% calcium had higher percent milk fat and fat yield than those fed 1.15% calcium diets, and cows fed fine-grind limestone had greater percent fat and fat yield than those fed normal-grind limestone. Four percent fat-corrected milk was higher for cows fed .77% calcium diets. Trends were similar for heifers in first lactation. Dry matter intake was higher for cows fed .77% calcium diets, and nutrient efficiency for milk synthesis favored cows fed fine-grind 1.15% calcium. Fecal pH was higher during wk 4 on treatment for cows fed high calcium diets; however, 8 wk were not different. Fecal starch and calcium and phosphorus in plasma were not different between treatments: however, heifers fed fine-grind 1.15% calcium showed a decrease of fecal starch with time.

Actinobacterial diversity in limestone deposit sites in Hundung, Manipur (India) and their antimicrobial activities

PubMed Central

Nimaichand, Salam; Devi, Asem Mipeshwaree; Tamreihao, K.; Ningthoujam, Debananda S.; Li, Wen-Jun

2015-01-01

Studies on actinobacterial diversity in limestone habitats are scarce. This paper reports profiling of actinobacteria isolated from Hundung limestone samples in Manipur, India using ARDRA as the molecular tool for preliminary classification. A total of 137 actinobacteria were clustered into 31 phylotypic groups based on the ARDRA pattern generated and representative of each group was subjected to 16S rRNA gene sequencing. Generic diversity of the limestone isolates consisted of Streptomyces (15 phylotypic groups), Micromonospora (4), Amycolatopsis (3), Arthrobacter (3), Kitasatospora (2), Janibacter (1), Nocardia (1), Pseudonocardia (1) and Rhodococcus (1). Considering the antimicrobial potential of these actinobacteria, 19 showed antimicrobial activities against at least one of the bacterial and candidal test pathogens, while 45 exhibit biocontrol activities against at least one of the rice fungal pathogens. Out of the 137 actinobacterial isolates, 118 were found to have at least one of the three biosynthetic gene clusters (PKS-I, PKS-II, NRPS). The results indicate that 86% of the strains isolated from Hundung limestone deposit sites possessed biosynthetic gene clusters of which 40% exhibited antimicrobial activities. It can, therefore, be concluded that limestone habitat is a promising source for search of novel secondary metabolites. PMID:25999937

Preservation of extraterrestrial 3He in 480-Ma-old marine limestones.

PubMed

Patterson, D B; Farley, K A; Schmitz, B

1998-11-01

We have measured the helium abundance and isotopic composition of a suite of Lower Ordovician marine limestones and associated fossil meteorites from Kinnekulle, Sweden. Limestone 3He/4He ratios as high as 11.5 times the atmospheric value in fused samples and up to 23 times atmospheric in a single step-heat fraction indicate the presence of extraterrestrial helium, and demonstrate that at least a fraction of the extraterrestrial 3He carried by interplanetary dust particles must be retained against diffusive and diagenetic losses for up to 480 Ma. The carrier phase has not been identified but is not magnetic. Extrapolation of high-temperature 3He diffusivities in these sediments is consistent with strong retention of extraterrestrial 3He under ambient Earth-surface conditions. Combination of the observed helium concentrations with sedimentation rates estimated from conodont biostratigraphy suggest that the flux of extraterrestrial 3He in the Early Ordovician was about 0.5 x 10(-12) cm3 STP cm-2 ka-1, ignoring potential post-deposition helium loss. This value is indistinguishable from the average 3He flux estimated for the Cenozoic Era. In contrast, previous studies of fossil meteorites, Ir abundances, and Os isotopic ratios in the limestone suggest that the total accretion rate of extraterrestrial material during the studied interval was at least an order of magnitude higher than the Cenozoic average. This disparity may reflect significant post-depositional loss of 3He from IDPs within these old limestones; if so, the match between the Ordovician flux and the Cenozoic average would be fortuitous. Alternatively, the size distribution of infalling objects during the Early Ordovician may have been enriched only in extraterrestrial material too large to retain 3He during atmospheric entry heating (> approximately 30 micrometers). The fossil meteorites themselves also preserve extraterrestrial helium. Meteorite 3He concentrations of 2 to 9 x 10(-12) cm3 STP g-1 are

Geochronological and Taxonomic Revisions of the Middle Eocene Whistler Squat Quarry (Devil’s Graveyard Formation, Texas) and Implications for the Early Uintan in Trans-Pecos Texas

PubMed Central

Campisano, Christopher J.; Kirk, E. Christopher; Townsend, K. E. Beth; Deino, Alan L.

2014-01-01

The Whistler Squat Quarry (TMM 41372) of the lower Devil’s Graveyard Formation in Trans-Pecos Texas is a middle Eocene fossil locality attributed to Uintan biochronological zone Ui1b. Specimens from the Whistler Squat Quarry were collected immediately above a volcanic tuff with prior K/Ar ages ranging from ∼47–50 Ma and below a tuff previously dated to ∼44 Ma. New 40Ar/39Ar analyses of both of the original tuff samples provide statistically indistinguishable ages of 44.88±0.04 Ma for the lower tuff and 45.04±0.10 Ma for the upper tuff. These dates are compatible with magnetically reversed sediments at the site attributable to C20r (43.505–45.942 Ma) and a stratigraphic position above a basalt dated to 46.80 Ma. Our reanalysis of mammalian specimens from the Whistler Squat Quarry and a stratigraphically equivalent locality significantly revises their faunal lists, confirms the early Uintan designation for the sites, and highlights several biogeographic and biochronological differences when compared to stratotypes in the Bridger and Uinta Formations. Previous suggestions of regional endemism in the early Uintan are supported by the recognition of six endemic taxa (26% of mammalian taxa) from the Whistler Squat Quarry alone, including three new taxa. The revised faunal list for the Whistler Squat Quarry also extends the biostratigraphic ranges of nine non-endemic mammalian taxa to Ui1b. PMID:24988115

Artesian Well Abandonment at Launch Complex 39A

NASA Technical Reports Server (NTRS)

Morgan, Lindsay; Johansen, Deda

2015-01-01

The artesian well tasked for abandonment was located on the LOX side (northwest area) of the launch complex. The exact date of well installation is unknown. The well was no longer in use at the time of the abandonment request, but was previously utilized under St. Johns River Water Management District (SJRWMD) consumptive use permit (No. 50054) for the Floridian Aquifer. The exact construction details of the LOX artesian well were also unknown; however, a similar-type artesian well was previously located on the LH2 side of the site, which was abandoned in 2012. Based on discussions with the NASA RPM and review of the LH2 artesian well abandonment completion report, the LH2 artesian well was reported to be an 8-inch diameter, 330-foot deep well. The NASA RPM communicated that the LOX artesian well was likely to be an 8-inch diameter, 380-foot deep well. This information was used for scoping, and was subsequently confirmed to be substantially accurate. No additional information could be found for the LOX artesian well using the NASA Remediation Information System (RIS).

Plant Guide: Limestone hawksbeard: Crepis intermedia

Treesearch

L. St. John; D. Tilley

2012-01-01

Sunflower family (Asteraceae). Limestone hawksbeard is a native perennial forb with one or two stems arising from a taproot. Plants are 30-70cm tall and basal leaves are 10-40 cm long, pinnatifid, with a fairly broad, undivided midstrip and entire or dentate segments. Plants are densely or sparsely gray-tomentulose. There are 10-60 heads per plant that are 7-12...

Franciscan complex calera limestones: Accreted remnants of farallon plate oceanic plateaus

USGS Publications Warehouse

Tarduno, J.A.; McWilliams, M.; Debiche, M.G.; Sliter, W.V.; Blake, M.C.

1985-01-01

The Calera Limestone, part of the Franciscan Complex of northern California, may have formed in a palaeoenvironment similar to Hess and Shatsky Rises of the present north-west Pacific1. We report here new palaeomagnetic results, palaeontological data and recent plate-motion models that reinforce this assertion. The Calera Limestone may have formed on Farallon Plate plateaus, north of the Pacific-Farallon spreading centre as a counterpart to Hess or Shatsky Rises. In one model2, the plateaus were formed by hotspots close to the Farallon_Pacific ridge axis. On accretion to North America, plateau dissection in the late Cretaceous to Eocene (50-70 Myr) could explain the occurrence of large volumes of pillow basalt and exotic blocks of limestone in the Franciscan Complex. Partial subduction of the plateaus could have contributed to Laramide (70-40 Myr) compressional events3. ?? 1985 Nature Publishing Group.

New data towards the development of a comprehensive taphonomic framework for the Late Jurassic Cleveland-Lloyd Dinosaur Quarry, Central Utah

PubMed Central

Warnock, Jonathan P.; Eberhart, Shawn L.; Clawson, Steven R.; Noto, Christopher R.

2017-01-01

The Cleveland-Lloyd Dinosaur Quarry (CLDQ) is the densest deposit of Jurassic theropod dinosaurs discovered to date. Unlike typical Jurassic bone deposits, it is dominated by the presence of Allosaurus fragilis. Since excavation began in the 1920s, numerous hypotheses have been put forward to explain the taphonomy of CLDQ, including a predator trap, a drought assemblage, and a poison spring. In an effort to reconcile the various interpretations of the quarry and reach a consensus on the depositional history of CLDQ, new data is required to develop a robust taphonomic framework congruent with all available data. Here we present two new data sets that aid in the development of such a robust taphonomic framework for CLDQ. First, x-ray fluorescence of CLDQ sediments indicate elevated barite and sulfide minerals relative to other sediments from the Morrison Formation in the region, suggesting an ephemeral environment dominated by periods of hypereutrophic conditions during bone accumulation. Second, the degree of abrasion and hydraulic equivalency of small bone fragments dispersed throughout the matrix were analyzed from CLDQ. Results of these analyses suggest that bone fragments are autochthonous or parautochthonous and are derived from bones deposited in the assemblage rather than transported. The variability in abrasion exhibited by the fragments is most parsimoniously explained by local periodic re-working and re-deposition during seasonal fluctuations throughout the duration of the quarry assemblage. Collectively, these data support previous interpretations that the CLDQ represents an attritional assemblage in a poorly-drained overbank deposit where vertebrate remains were introduced post-mortem to an ephemeral pond during flood conditions. Furthermore, while the elevated heavy metals detected at the Cleveland-Lloyd Dinosaur Quarry are not likely the primary driver for the accumulation of carcasses, they are likely the result of multiple sources; some metals may be

Stone Quarrying, Crushing and Screening Facilities General Air Quality Permit Request for Coverage: Unimin Corporation - Unimin Flat Storage

EPA Pesticide Factsheets

Documents related to Request for Coverage under Stone Quarrying, Crushing and Screening Facilities General Permit, for the Unimin Corporation Silica Sand Rail Transloading Facility on the Fort Berhold Indian Reservation, North Dakota.

In vitro receptivity of carbonate rocks to endolithic lichen-forming aposymbionts.

PubMed

Favero-Longo, Sergio E; Borghi, Alessandro; Tretiach, Mauro; Piervittori, Rosanna

2009-10-01

Sterile cultured isolates of lichen-forming aposymbionts have not yet been used to investigate lichen-rock interactions under controlled conditions. In this study mycobionts and photobiont of the endolithic lichens Bagliettoa baldensis and Bagliettoa marmorea were isolated and inoculated with coupons of one limestone and four marbles commonly employed in the Cultural Heritage framework. After one year of incubation, microscopic observations of polished cross-sections were performed to verify if the typical colonization patterns observed in the field may be reproduced in vitro and to evaluate the receptivity of the five lithotypes to endolithic lichens. The mycobionts of the two species developed both on the surface of and within all the lithotypes, showing different penetration pathways which depend on mineralogical and structural features and highlight different receptivity. By contrast, algae inoculated with the coupons did not penetrate them. Observations suggest that the hyphal penetration along intrinsic discontinuities of rocks is a relatively fast phenomenon when these organisms are generally considered as slow-growing. Samples from limestone outcrops and abandoned marble quarries, colonized by the same species or other representatives of Verrucariaceae, showed penetration pathways intriguingly similar to those reproduced in vitro and highlighted that lichen-driven erosion processes only increase the availability of hyphal passageways after a long-term colonization. These results show that in vitro incubation of sterile cultured lichen-forming ascomycetes with rock coupons is a practicable experimental system to investigate the lichen-rock interactions under controlled conditions and, together with analysis in situ, may support decisions on conservative treatments of historical and cultural significant stone substrata.

The negative effect of environmental geological conditions of some geo-archaeological sites of North Coast and Alexandria

NASA Astrophysics Data System (ADS)

Ibrahim, Hani; Kamh, Gamal

2005-12-01

Three geo-archaeological sites at the North Coast and Alexandria, namely, the Alexandria wall (El Shalalat Park site), Abu Soir temple, and Marina excavations, were investigated to determine the negative impact of a salty environmental condition. The monuments suffer from rock decay of different rates. The geo-archaeological sites were built mainly from oolitic limestone blocks (i.e., the Alexandria wall at the El Shalalat Park site and Abu Soir temple) or excavated on them (i.e., Marina excavations). Field inspection and a lab analysis were carried out to understand the weathering mechanism. Salt weathering criteria such as disintegration, pitting, scaling, exfoliation, and honeycomb are observed on the Alexandria wall and upper parts of the Abu Soir temple, while dangerous cracks are detected on the Marina excavation tombs. The petrographic study of the oolitic limestone samples shows that they consist mainly of oolities and drusy sparite as a cement (oolitic grainstone). Some oolities have quartz grains as nuclei. Hydrochemical analysis shows that the total dissolved salts of extracted solutions of the North Coast quarry samples range from 539 to 686 ppm and dramatically increase (i.e., ten times) for extracted solutions from monument samples, ranging from 5395 to 6880 ppm. The dominant cation is sodium while the dominant anion is chlorine. Acid insoluble residue analysis shows that the carbonate content ranges from 89.2% to 96.4% for fresh samples from quarries and from 9.2% to 94.8% for weathered monument samples. The weight loss of the quarry oolitic limestone samples range from 30.7% to 32.7% and its physical and mechanical properties become worse after being subjected to 15 cycles of a durability simulation soundness test (using a sodium sulphate solution). Our main recommendations are to use suitable grouting for binding the cracks, high durability reconstruction rocks, and suitable cleaning methods to remove salts from the monuments.

Sedum tarokoense (Crassulaceae), a new species from a limestone area in Taiwan.

PubMed

Lu, Chang-Tse; Lin, Hung-Wen; Liou, Wei-Ting; Wang, Jenn-Che

2013-12-01

An unknown Sedum was found from the limestone region in Taiwan. After a detailed comparison with other congeners in Taiwan and neighboring countries, we identified this plant as a new species. This new taxon resembles S. nokoense Yamamoto, S. alfredii Hance, and S. uniflorum Hook. & Arn. subsp. oryzifolium (Makino) H. Ohba, but differs in leaf shape, sepal morphology, and seed testa micro-morphology. Ecologically, this new taxon occurs exclusively on limestone, while S. nokoense and S. alfredii grow in non-limestone areas and S. uniflorum subsp. oryzifolium is only found on sandy seashores. Sedum tarokoense H.W. Lin & J.C. Wang is described as a new species. We provide a description, line drawing, and distribution map, as well as photograph, a key and a table to distinguish S. tarokoense from its related species.

4. INTERIOR OF ABANDONED SANTA ANA CANAL TUNNEL, SHOWING CEMENT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. INTERIOR OF ABANDONED SANTA ANA CANAL TUNNEL, SHOWING CEMENT TROUGH FLOOR AND UNFINISHED GRANITE ROOF. VIEW TO SOUTHWEST. - Santa Ana River Hydroelectric System, Abandoned Tunnel, Redlands, San Bernardino County, CA

The Portuguese Lioz, a Monumental Limestone

NASA Astrophysics Data System (ADS)

Silva, Zenaide

2017-04-01

Lioz is a microcrystalline limestone which occurs in Portugal and outcrops in the Lisbon area and its neighboring counties Oeiras, Pero Pinheiro, Lameiras. The rock is whitish to light and dark pink and contains 120 million years old rudists fossils. This fossiliferous content imprints a decorative aspect to the rock contributing to its very wide use as construction material and its favorite use in churches and official monuments making it the Royal Stone in Portugal along the XVII and XVIII centuries. Lisbon has the best exposition of Lioz as a fundamental stone in several monuments, the best examples being the Jeronimos Monastery, the Belém Tower, the Cultural Center in Belém and many old churches spread in Lisbon area. Among the latter the Jesuit Church of São Roque is a special example. The fact that the rock stratigraphic sequence allows the different rock colors as white, light and dark pink and a yellow facies variety in a local occurrence (Negrais yellow) makes it a special source for decorative patterns that can be found in a few churches in Lisbon, Évora, Mafra exhibiting "embutidos" technique, of indian origin and inspired on contemporaneous Italian churches. Mafra is the place where a monumental architectural set, composed by three integrated constructions, was built in the XVIII century by king D.João V using Lioz limestone as the main rock material, in all available colors. Along the XVII and XVIII centuries, the rock was transported to some portuguese colonies, mainly as ballast to improve the navigability of the boats, and used at the destinations as construction material for monuments, official buildings and churches. Brazil and especially Salvador, in Bahia, is the best example of that, where Lioz is beautifully exposed in monuments and as true art in many churches where the Portuguese or Italian influences are very strong. All these facts make the Portuguese Lioz Limestone as very representative of the Heritage present in Portugal and its

Investigations of a Cretaceous limestone with spectral induced polarization and scanning electron microscopy

NASA Astrophysics Data System (ADS)

Johansson, Sara; Sparrenbom, Charlotte; Fiandaca, Gianluca; Lindskog, Anders; Olsson, Per-Ivar; Dahlin, Torleif; Rosqvist, Håkan

2017-02-01

Characterization of varying bedrock properties is a common need in various contexts, ranging from large infrastructure pre-investigations to environmental protection. A direct current resistivity and time domain induced polarization (IP) survey aiming to characterize properties of a Cretaceous limestone was carried out in the Kristianstad basin, Sweden. The time domain IP data was processed with a recently developed method in order to suppress noise from the challenging urban setting in the survey area. The processing also enabled extraction of early decay times resulting in broader spectra of the time decays and inversion for Cole-Cole parameters. The aims of this study is to investigate if large-scale geoelectrical variations as well as small-scale structural and compositional variations exist within the Kristianstad limestone, and to evaluate the usefulness of Cole-Cole inverted IP data in early time ranges for bedrock characterization. The inverted sections showed variations within the limestone that could be caused by variations in texture and composition. Samples from a deep drilling in the Kristianstad basin were investigated with scanning electron microscopy and energy dispersive X-ray spectroscopy, and the results showed that varying amounts of pyrite, glauconite and clay matrix were present at different levels in the limestone. The local high IP anomalies in the limestone could be caused by these minerals otherwise the IP responses were generally weak. There were also differences in the texture of the limestone at different levels, governed by fossil shapes and composition, proportions of calcareous cement and matrix as well as amount of silicate grains. Textural variations may have implications on the variation in Cole-Cole relaxation time and frequency factor. However, more research is needed in order to directly connect microgeometrical properties in limestone to spectral IP responses. The results from this study show that it is possible to recover

High Cigarette and Poly-Tobacco Use Among Workers in a Dusty Industry: New Jersey Quarry Workers.

PubMed

Graber, Judith M; Worthington, Karen; Almberg, Kirsten S; Meng, Qingyu; Rose, Cecile S; Cohen, Robert A

2016-04-01

Tobacco use is high among US extraction and construction workers, who can also incur occupational dust exposure. Information on different types of tobacco use among quarry/mine workers is sparse. During mandated training sessions, New Jersey quarry workers were surveyed about their tobacco use. Prevalence was calculated for single and multiple tobacco use by demographic and workplace characteristics; logistic regression was used to assess associations with smoking. Two hundred forty (97.1%) workers completed surveys. Among respondents, 41.7% [95% confidence interval (95% CI) 35.4 to 48.3] currently used any tobacco product of whom 28.1% smoked cigarettes. In multivariate analysis, positive associations with smoking included working as a contractor versus mine employee (odds ratio 2.32, 95% CI 1.01 to 5.36) and a usual job title of maintenance (odds ratio 2.02, 95% CI 0.87 to 4.94). Industry-specific information may be helpful in developing targeted tobacco-cessation programs.

On the way of Friuli "yellow villages": the use of a calcareous-dolomitic sandstone in the surroundings of the quarrying area through the centuries.

NASA Astrophysics Data System (ADS)

Frangipane, Anna

2017-04-01

The role of local stone building material in cultural and technological heritage is based on the definition of the area of use, as related to ancient transportation networks, allowing the movement of heavy blocks from the quarries to the building sites. It is the case of the result of several surveys carried out for the detection of the architectural elements, dating from Middle Age to 20th century, made of a yellowish calcareous-dolomitic sandstone, which have been found, hidden among renovated buildings and new construction, in Friuli region (NE Italy). on the way between the quarrying piedmont western area and the towns of Udine and Spilimbergo. Starting from the definition of the quarrying area, the contribution give notice of such architectural elements (frames, columns, …), both in vernacular architecture and in relevant buildings, putting in evidence the period of their realisation and their technological features.

Optimization of limestone drains for long- term treatment of acidic mine drainage, Swatara Creek Basin, Schuylkill County, PA

USGS Publications Warehouse

Cravotta, Charles A.; Ward, S.J.; Koury, Daniel J.; Koch, R.D.

2004-01-01

Limestone drains were constructed in 1995, 1997, and 2000 to treat acidic mine drainage (AMD) from the Orchard, Buck Mtn., and Hegins discharges, respectively, in the Swatara Creek Basin, Southern Anthracite Coalfield, east-central Pennsylvania. This report summarizes the construction characteristics and performance of each of the limestone drains on the basis of influent and effluent quality and laboratory tests of variables affecting limestone dissolution rates. Data for influent and effluent indicate substantial alkalinity production by the Orchard and Buck Mtn. limestone drains and only marginal benefits from the Hegins drain. Nevertheless, the annual alkalinity loading rates have progressively declined with age of all three systems. Collapsible-container (cubitainer) testing was conducted to evaluate current scenarios and possible options for reconstruction and maintenance of the limestone drains to optimize their long-term performance. The cubitainer tests indicated dissolution rates for the current configurations that were in agreement with field flux data (net loading) for alkalinity and dissolved calcium. The dissolution rates in cubitainers were larger for closed conditions than open conditions, but the rates were comparable for coated and uncoated limestone for a given condition. Models developed on the basis of the cubitainer testing indicate (1) exponential declines in limestone mass and corresponding alkalinity loading rates with increased age of limestone drains and (2) potential for improved performance with enlargement, complete burial, and/or regular flushing of the systems.

A multistratigraphic approach to pinpoint the Permian-Triassic boundary in continental deposits: The Zechstein-Lower Buntsandstein transition in Germany

NASA Astrophysics Data System (ADS)

Scholze, Frank; Wang, Xu; Kirscher, Uwe; Kraft, Johannes; Schneider, Jörg W.; Götz, Annette E.; Joachimski, Michael M.; Bachtadse, Valerian

2017-05-01

The Central European Basin is very suitable for high-resolution multistratigraphy of Late Permian to Early Triassic continental deposits. Here the well exposed continuous transition of the lithostratigraphic Zechstein and Buntsandstein Groups of Central Germany was studied for isotope-chemostratigraphy (δ13Corg, δ13Ccarb, δ18Ocarb), major and trace element geochemistry, magnetostratigraphy, palynology, and conchostracan biostratigraphy. The analysed material was obtained from both classical key sections (abandoned Nelben clay pit, Caaschwitz quarries, Thale railway cut, abandoned Heinebach clay pit) and a recent drill core section (Caaschwitz 6/2012) spanning the Permian-Triassic boundary. The Zechstein-Buntsandstein transition of Central Germany consists of a complex sedimentary facies comprising sabkha, playa lake, aeolian, and fluvial deposits of predominantly red-coloured siliciclastics and intercalations of lacustrine oolitic limestones. The new data on δ13Corg range from - 28.7 to - 21.7 ‰ showing multiple excursions. Most prominent negative shifts correlate with intercalations of oolites and grey-coloured clayey siltstones, while higher δ13Corg values correspond to an onset of palaeosol overprint. The δ13Ccarb values range from - 9.7 to - 1.3 ‰ with largest variations recorded in dolomitic nodules from the Zechstein Group. In contrast to sedimentary facies shifts across the Zechstein-Buntsandstein boundary, major element values used as a proxy (CIA, CIA*, CIA-K) for weathering conditions indicate climatic stability. Trace element data used for a geochemical characterization of the Late Permian to Early Triassic transition in Central Germany indicate a decrease in Rb contents at the Zechstein-Buntsandstein boundary. New palynological data obtained from the Caaschwitz quarry section reveal occurrences of Late Permian palynomorphs in the Lower Fulda Formation, while Early Triassic elements were recorded in the upper part of the Upper Fulda Formation

Vatica najibiana (Dipterocarpaceae), a new species from limestone in Peninsular Malaysia

PubMed Central

Ummul-Nazrah, Abdul Rahman; Mohd Hairul, Mohd Amin; Kamin, Imin; Kiew, Ruth; Ong, Poh Teck

2018-01-01

Abstract Vatica najibiana Ummul-Nazrah (Dipterocarpaceae), from the Relai Forest Reserve, Gua Musang, Kelantan and Gua Tanggang, Merapoh, Pahang, is described and illustrated. This species is Endangered and known from small populations restricted to two isolated karst limestone hills. The type locality, Relai Forest Reserve limestone, is currently under threat from encroaching oil palm plantations and ongoing logging, which, if it continues, will threaten the Kelantan population with extinction. The morphology of V. najibiana and the similar V. odorata subsp. odorata and V. harmandiana is compared.

Dietary adaptations of Assamese macaques (Macaca assamensis) in limestone forests in Southwest China.

PubMed

Huang, Zhonghao; Huang, Chengming; Tang, Chuangbin; Huang, Libin; Tang, Huaxing; Ma, Guangzhi; Zhou, Qihai

2015-02-01

Limestone hills are an unusual habitat for primates, prompting them to evolve specific behavioral adaptations to the component karst habitat. From September 2012 to August 2013, we collected data on the diet of one group of Assamese macaques living in limestone forests at Nonggang National Nature Reserve, Guangxi Province, China, using instantaneous scan sampling. Assamese macaques were primarily folivorous, young leaves accounting for 75.5% and mature leaves an additional 1.8% of their diet. In contrast, fruit accounted for only 20.1%. The young leaves of Bonia saxatilis, a shrubby, karst-endemic bamboo that is superabundant in limestone hills, comprised the bulk of the average monthly diet. Moreover, macaques consumed significantly more bamboo leaves during the season when the availability of fruit declined, suggesting that bamboo leaves are an important fallback food for Assamese macaques in limestone forests. In addition, diet composition varied seasonally. The monkeys consumed significantly more fruit and fewer young leaves in the fruit-rich season than in the fruit-lean season. Fruit consumption was positively correlated with fruit availability, indicating that fruit is a preferred food for Assamese macaques. Of seventy-eight food species, only nine contributed >0.5% of the annual diet, and together these nine foods accounted for 90.7% of the annual diet. Our results suggest that bamboo consumption represents a key factor in the Assamese macaque's dietary adaptation to limestone habitat. © 2014 Wiley Periodicals, Inc.

Facies development and paleoenvironment of the Hajajah Limestone Member, Aruma Formation, central Saudi Arabia

NASA Astrophysics Data System (ADS)

El-Sorogy, Abdelbaset S.; Ismail, Abdelmoneim; Youssef, Mohamed; Nour, Hamdy

2016-12-01

The Campanian Hajajah Limestone Member of the Aruma Formation was formed during two regressive episodes. Each of them formed of three depositional facies, from base to top: 1) intra-shelf basin facies, made up of fossiliferous green shale and mudstone with ostracods and badly preserved foraminifers. 2) fore-reef facies, consists of hard, massive, marly coralline limestone. The upper part is rich with low divers, badly to moderate preserved, solitary and colonial corals, and, 3) back reef and near-shore facies, consists of fossiliferous sandy dolomitized, bioturbated limestone with abundant reworked corals, bivalves, gastropods, and aggregate grains. On the basis of field observations, micro-and macrofossils and microfacies analysis, the Hajajah Limestone Member was deposited in distal marine settings below storm wave base in a low-energy environment changed upward to fore-reef framework in an open marine environment with moderate to high energy conditions and terminated with shallow marine facies with accumulation of skeletal grains by storms during regression.

Analysis of conditions and the concept of multidirectional revitalization of the dolomite quarry in Siewierz

NASA Astrophysics Data System (ADS)

Pawełczyk, Katarzyna

2018-01-01

The development of mining of rock raw materials in Poland has significantly contributed to economic growth and the quality of life of local communities. However, mining activity, besides a number of positive effects, also implies broadly understood changes in the environment and the formation of brownfields. Reclamation and redevelopment of post-industrial areas, and especially post-mining areas, is currently a huge environmental and socio-economic challenge. Revitalization of post-mining areas is particularly important for small towns and municipalities, where mining was one of the main pillars of development and prosperity. An example of such a municipality is Siewierz in Silesian Voivodship. In the paper analysis the conditions have been conducted and the concept of revitalization of dolomite quarry Górnicze Zakłady Dolomitowe S.A. has been proposed. The AHP method has been used to analyse and select the optimal method of revitalization. As a result of the analysis, the concept of multidirectional revitalization with socially, economically and environmentally beneficial functions has been created, maximizing the potential of the quarry.

30 CFR 938.20 - Approval of Pennsylvania abandoned mine land reclamation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Approval of Pennsylvania abandoned mine land... PENNSYLVANIA § 938.20 Approval of Pennsylvania abandoned mine land reclamation plan. The Pennsylvania Abandoned... are available at the following locations: (a) Pennsylvania Department of Environmental Resources...

Determinants of tuberculosis transmission and treatment abandonment in Fortaleza, Brazil.

PubMed

Harling, Guy; Lima Neto, Antonio S; Sousa, Geziel S; Machado, Marcia M T; Castro, Marcia C

2017-05-25

Tuberculosis (TB) remains a public health problem, despite recent achievements in reducing incidence and mortality rates. In Brazil, these achievements were above the worldwide average, but marked by large regional heterogeneities. In Fortaleza (5th largest city in Brazil), the tuberculosis cure rate has been declining and treatment abandonment has been increasing in the past decade, despite a reduction in incidence and an increase in directly observed therapy (DOT). These trends put efforts to eliminate tuberculosis at risk. We therefore sought to determine social and programmatic determinants of tuberculosis incidence and treatment abandonment in Fortaleza. We analyzed sociodemographic and clinical data for all new tuberculosis cases notified in the Notifiable Diseases Information System (SINAN) from Fortaleza between 2007 and 2014. We calculated incidence rates for 117 neighborhoods in Fortaleza, assessed their spatial clustering, and used spatial regression models to quantify associations between neighborhood-level covariates and incidence rates. We used hierarchical logistic regression models to evaluate how individual- and neighborhood-level covariates predicted tuberculosis treatment abandonment. There were 12,338 new cases reported during the study period. Case rates across neighborhoods were significantly positively clustered in two low-income areas close to the city center. In an adjusted model, tuberculosis rates were significantly higher in neighborhoods with lower literacy, higher sewerage access and homicide rates, and a greater proportion of self-reported black residents. Treatment was abandoned in 1901 cases (15.4%), a rate that rose by 71% between 2007 and 2014. Abandonment was significantly associated with many individual sociodemographic and clinical factors. Notably, being recommended for DOT was protective for those who completed DOT, but associated with abandonment for those who did not. Low socioeconomic status areas have higher tuberculosis

Monitoring regional effects of high pressure injection of wastewater in a limestone aquifer

USGS Publications Warehouse

Faulkner, Glen L.; Pascale, Charles A.

1975-01-01

More than 10 billion gallons (38 × 106 m3) of acid industrial liquid waste has been injected in about 11 years under high pressure into a saline-water-filled part of a limestone aquifer of low transmissivity between 1,400 and 1,700 feet (430 and 520 m) below land surface near Pensacola, Florida. A similar waste disposal system is planned for the same zone at a site about 8.5 miles (13.7 km) to the east. The injection zone is the lower limestone of the Floridan aquifer. The lower limestone is overlain by a confining layer of plastic clay about 220 feet (67 m) thick at the active injection site and underlain by another confining layer of shale and clay. The upper confining layer is overlain by the upper limestone of the Floridan aquifer.The active injection system consists of two injection wells about a quarter of a mile (0.4 km) apart and three monitor wells. Two of the monitor wells (deep monitors) are used to observe hydraulic and geochemical effects of waste injection in the injection zone at locations about 1.5 miles (2.4 km) south and 1.9 miles (3.1 km) north of the center of the injection site. The third well (shallow monitor), used to observe any effects in the upper limestone, is about 100 feet (30 m) from one of the injection wells. Since 1972 the injection zone has also been monitored at a test well at the planned new injection site. Three more monitor wells in the injection zone were activated in early 1974 at sites 17 miles (27 km) northeast, 22 miles (35 km) east and 33 miles (53 km) northeast of the injection site. The six deep monitors provide a system for evaluating the regional effects of injecting wastes. No change in pressure or water quality due to injection was, by mid-1974, evident in the upper limestone at the injection site, but static pressures in the lower limestone at the site had increased 8 fold since injection began in 1963. Chemical analyses indicated probable arrival of the diluted waste at the south monitor well in 1973. By mid-1974

Introducing two federally listed carbonate-endemic plants onto a disturbed site in the San Bernardino Mountains, California

Treesearch

Orlando Mistretta; Scott D. White

2001-01-01

Erigeron parishii and Eriogonum ovalifolium var. vineum are federally listed local endemic plants occurring almost exclusively on carbonate soils in the northeastern San Bernardino Mountains. In 1991 and 1992, both species were planted onto a barren cut slope above a limestone quarry haul road. The plants were irrigated through the first summer and fall after planting...

77 FR 35751 - Wisconsin Central Ltd.-Abandonment Exemption-in Manitowoc County, WI

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-14

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. AB 303 (Sub-No. 39X)] Wisconsin Central Ltd.--Abandonment Exemption--in Manitowoc County, WI Wisconsin Central Ltd. (WCL) has filed a verified notice of exemption under 49 CFR part 1152 subpart F--Exempt Abandonments to abandon 6...

Noise-Induced Hearing Loss Among Quarry Workers in a North-Eastern State of Malaysia: A Study on Knowledge, Attitude and Practice

PubMed Central

Ismail, Ahmad Filza; Daud, Aziah; Ismail, Zaliha; Abdullah, Baharudin

2013-01-01

Objectives Noise is known to be one of the environmental and occupational hazards listed in the Factory and Machinery Act 1967. Quarries with loud deafening sounds from trucks and machineries pose the risk of noise-induced hearing loss to workers. This study was designed to assess the knowledge, attitude and practice towards noise-induced hearing loss and to determine the prevalence of noise-induced hearing loss and its associated factors among quarry workers in a north-eastern state of Malaysia. Methods A cross-sectional study was conducted at six quarries in a north-eastern state of Malaysia, with 97 consented respondents who answered a validated version of a questionnaire and underwent pure tone audiogram. The respondents were male, aged between 18 to 50 years, working in the quarry area for at least 6-months duration with no family history of ear diseases. Results The mean percentage scores of knowledge, attitude and practice were 44 (11), 70 (10) and 28 (16) percent, respectively. The prevalence of noise-induced hearing loss was found to be 57 (95% CI: 47, 67) with 46 (84%) having mild and moderate noise-induced hearing loss, and 34 (62%) involved both ears. Multiple logistic regressions showed that age and practice score were the associated factors with odd ratios of 1.1 (95% CI: 1.1, 1.2; p<0.001) and 0.9 (95% CI: 0.8, 1.0; p=0.008), respectively. Conclusion The knowledge, attitude and practice scores of the respondents were poor and the high prevalence of noise-induced hearing loss was contributed by factors such as poor practice and old age. PMID:24044059

Visual Analysis as a design and decision-making tool in the development of a quarry

Treesearch

Randall Boyd Fitzgerald

1979-01-01

In order to obtain local and state government approvals, an environmental impact analysis of the mining and reclamation of a proposed hard rock quarry was required. High visibility of the proposed mining area from the adjacent community required a visual impact analysis in the planning and design of the project. The Visual Analysis defined design criteria for the...

DEVELOPMENTS IN LIMB (LIMESTONE INJECTION MULTISTAGE BURNER) TECHNOLOGY

EPA Science Inventory

The paper describes the most recent results from the Limestone Injection Multistage Burner (LIMB) program, results from the wall-fired demonstration. Tests were conducted to determine the efficacy of commercial calcium hydroxide--Ca(OH)2--supplied by Marblehead Lime Co. and of ca...

Three-dimensional facies architecture of the Salem Limestone (middle Mississippian), Eastern Margin of Illinois basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nadeem, A.; Keith, B.D.; Thompson, T.A.

Mapping of sedimentary surfaces in the Middle Mississippian Salem Limestone exposed on sawed quarry walls in south-central Indiana has revealed a hierarchy of depositional units representative of the extremely dynamic hydrographic regime of the upper shoreface zone. The depositional units on the scale of microform and mesoform are represented by the microfacies and the facies respectively. Based on their hierarchy, genetically related depositional units and associated bounding surfaces were grouped together to construct four architectural packages (APs) of the scale of mesoforms. AP-I is dominantly an echinoderm- and bryozoan-rich grainstone and consists of bedforms ranging from small ripples bounded bymore » first-order surfaces to two- and three- dimensional megaripples bounded by the second-order surfaces. It formed as part of a giant ramp (asymmetric wavefield) within the intrashoal channel setting. AP-II, also a skeletal grainstone, is a complex of giant sandwaves that moved into the area under the infulence of a storm and partly filled the basal channel form of AP-I. Large avalanche foresets with tangential toesets prevail. AP-III is a dark-gray spatially discontinuous skeletal grainstone to packstone that laterally grades into a skeletal packstone to wackestone. It locally developed overhangs, rips-ups, and hardground on its upper surface. AP-IV is a skeletal and oolitic grainstone formed of tabular two-dimensional megaripples (planar cross-beds) and three-dimensional oscillatory megaripples (trough cross-beds). These architectural packages based on the bedform architecture and micro-and mesoscale compositional changes can be used to characterize micro-, meso, and macroscale heterogeneities. Models of facies architecture from this and similar outcrop studies can be applied to the subsurface Salem reservoirs in the Illinois Basin using cores.« less

Modelling mechanical behaviour of limestone under reservoir conditions

NASA Astrophysics Data System (ADS)

Carvalho Coelho, Lúcia; Soares, Antonio Claudio; Ebecken, Nelson Francisco F.; Drummond Alves, José Luis; Landau, Luiz

2006-12-01

High porosity and low permeability limestone has presented pore collapse. As fluid is withdrawn from these reservoirs, the effective stresses acting on the rock increase. If the strength of the rock is overcome, pore collapse may occur, leading to irreversible compaction of porous media with permeability and porosity reduction. It impacts on fluid withdrawal. Most of reservoirs have been discovered in weak formations, which are susceptible to this phenomenon. This work presents a study on the mechanical behaviour of a porous limestone from a reservoir located in Campos Basin, offshore Brazil. An experimental program was undergone in order to define its elastic plastic behaviour. The tests reproduced the loading path conditions expected in a reservoir under production. Parameters of the cap model were fitted to these tests and numerical simulations were run. The numerical simulations presented a good agreement with the experimental tests. Copyright

32 CFR 635.31 - Lost, abandoned, or unclaimed property.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Lost, abandoned, or unclaimed property. 635.31 Section 635.31 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) LAW ENFORCEMENT AND CRIMINAL INVESTIGATIONS LAW ENFORCEMENT REPORTING Offense Reporting § 635.31 Lost, abandoned, or unclaimed property. This is...

Nurses' Attitudes and Knowledge of Their Roles in Newborn Abandonment

PubMed Central

Cesario, Sandra K.

2003-01-01

The practice of abandoning newborns shortly after birth has always existed. Occurring in primitive and contemporary societies, the motivations for newborn abandonment are varied and dependent upon the social norms of a specific geographic region at a given point in time. Because the desire to abandon an infant has had no support system in American society, such unwanted infants have been abandoned in a manner leading to their deaths. In response, many states have passed safe-haven legislation to save the lives of unwanted newborns. The laws typically specify a mother's ability to “abandon” her child to a medical service provider. However, judgmental attitudes and a lack of accurate information may impede a health care provider's ability to carry out a safe-haven law. The study described here examines a sample of nurses in a state with a safe-haven law. The study revealed no significant correlation between a nurse's knowledge, attitude, and self-perception of preparedness to manage a newborn abandonment event. owever, the outcomes highlight the negative attitudes and lack of knowledge many nurses possess regarding newborn abandonment and the women who commit this act. Educational programs for all health care providers and the community are essential to the efficacy of the legislation that currently exists. Continued multidisciplinary strategizing and general awareness are needed to serve as catalysts to build supports for unwanted newborns and their safe assimilation into the community. PMID:17273338

Quarry identification of historical building materials by means of laser induced breakdown spectroscopy, X-ray fluorescence and chemometric analysis

NASA Astrophysics Data System (ADS)

Colao, F.; Fantoni, R.; Ortiz, P.; Vazquez, M. A.; Martin, J. M.; Ortiz, R.; Idris, N.

2010-08-01

To characterize historical building materials according to the geographic origin of the quarries from which they have been mined, the relative content of major and trace elements were determined by means of Laser Induced Breakdown Spectroscopy (LIBS) and X-ray Fluorescence (XRF) techniques. 48 different specimens were studied and the entire samples' set was divided in two different groups: the first, used as reference set, was composed by samples mined from eight different quarries located in Seville province; the second group was composed by specimens of unknown provenance collected in several historical buildings and churches in the city of Seville. Data reduction and analysis on laser induced breakdown spectroscopy and X-ray fluorescence measurements was performed using multivariate statistical approach, namely the Linear Discriminant Analysis (LDA), Principal Component Analysis (PCA) and Soft Independent Modeling of Class Analogy (SIMCA). A clear separation among reference sample materials mined from different quarries was observed in Principal Components (PC) score plots, then a supervised soft independent modeling of class analogy classification was trained and run, aiming to assess the provenance of unknown samples according to their elemental content. The obtained results were compared with the provenance assignments made on the basis of petrographical description. This work gives experimental evidence that laser induced breakdown spectroscopy measurements on a relatively small set of elements is a fast and effective method for the purpose of origin identification.

Risk of groundwater inrush in subterranean gypsum quarries: the case study of Moncalvo near Asti (North Italy)

NASA Astrophysics Data System (ADS)

Banzato, Cinzia; Fiorucci, Adriano; Gianotti, Alberto; de Waele, Jo; Vigna, Bartolomeo

2010-05-01

During the realisation of underground excavations in gypsum bedrock there is a possibility of intercepting large karst voids that can be completely filled with water under a considerable hydraulic pressure. The casual breaching of such voids can cause sudden and abundant water inrushes with consequences concerning safety of the excavation area and flooding of the tunnels. The presence of air-filled caves of great dimensions can also cause problems related to collapse of walls, ceilings and floors. In the subterranean quarry of Moncalvo d'Asti (Central Piedmont, Italy) in January 2005 an important inrush (60,000 m3 overnight) occurred causing damage to machinery and the flooding of several kilometres of underground tunnels. This inrush was caused by the breaching of a thin diaphragm of rock that separated the quarry from a large water-filled cave with water pressure of around 300 kPa along the front of the excavation. The rapid emptying of this void has caused a partial collapse of the roof of one of the largest cave chambers with the formation at the surface of a 20 metre wide sinkhole. To prevent similar phenomena to happen in the future a hydrogeological study concerning the entire gypsum mass was carried out. These investigations included monitoring of water levels intercepted by a series of boreholes, measurements of flow rates of water veins encountered by the excavations and chemical analysis of the different types of water coming from several points. This study has evidenced the presence of different drainage networks and the existence of a main karst circuit fed by diffused infiltration and recharge from the overlying marly-silty deposits and from adjacent minor less karstified systems in particularly fractured sectors of the gypsum. The waters coming from the main karst circuit are chemically very different from the waters deriving from deeper pathways. To be able to continue the excavation of gypsum in safe conditions the water levels were lowered for a

Carbonate Minerals with Magnesium in Triassic Terebratula Limestone in the Term of Limestone with Magnesium Application as a Sorbent in Desulfurization of Flue Gases

NASA Astrophysics Data System (ADS)

Stanienda-Pilecki, Katarzyna

2017-09-01

This article presents the results of studies of Triassic (Muschelkalk) carbonate rock samples of the Terebratula Beds taken from the area of the Polish part of the Germanic Basin. It is the area of Opole Silesia. The rocks were studied in the term of possibility of limestone with magnesium application in desulfurization of flue gases executed in power plants. Characteristic features of especially carbonate phases including magnesium-low-Mg calcite, high-Mg calcite, dolomite and huntite were presented in the article. They were studied to show that the presence of carbonate phases with magnesium, especially high-Mg calcite makes the desulfurization process more effective. Selected rock samples were examined using a microscope with polarized, transmitted light, X-ray diffraction, microprobe measurements and FTIR spectroscopy. The results of studies show a domination of low magnesium calcite in the limestones of the Terebratula Beds. In some samples dolomite and lower amounts of high-Mg calcite occurred. Moreover, huntite was identified. The studies were very important, because carbonate phases like high-Mg calcite and huntite which occurred in rocks of the Triassic Terebratula Beds were not investigated in details by other scientists but they presence in limestone sorbent could influence the effectiveness of desulfurization process.

Low-Temperature Curing Strength Enhancement in Cement-Based Materials Containing Limestone Powder.

PubMed

Bentz, Dale P; Stutzman, Paul E; Zunino, Franco

2017-06-01

With the ongoing sustainability movement, the incorporation of limestone powder in cementitious binders for concrete in the U.S. has become a subject of renewed interest. In addition to accelerating the early age hydration reactions of cementitious systems by providing additional surfaces for nucleation and growth of products, limestone powder is also intriguing based on its influence on low-temperature curing. For example, previous results have indicated that the utilization of limestone powder to replace one quarter of the fly ash in a high volume fly ash mixture (40 % to 60 % cement replacement) produces a reduction in the apparent activation energy for setting for temperatures below 25 °C. In the present study, the relationship between heat release and compressive strength of mortars at batching/curing temperatures of 10 °C and 23 °C is investigated. For Portland-limestone cements (PLC) with limestone additions on the order of 10 %, a higher strength per unit heat release is obtained after only 7 d of curing in lime water. Surprisingly, in some cases, the absolute strength of these mortar cubes measured at 7 d is higher when cured at 10 °C than at 23 °C. Solubilities vs. temperature, reaction stoichiometries and enthalpies, and projected phase distributions based on thermodynamic modeling for the cementitious phases are examined to provide some theoretical insight into this strength enhancement. For a subset of the investigated cements, thermogravimetric analysis (TGA), quantitative X-ray diffraction (XRD), and scanning electron microscopy (SEM) are conducted on 7-d paste specimens produced at the two temperatures to examine differences in their reaction rates and the phases produced. The strength enhancement observed in the PLC cements is related to the cement hydration products formed in the presence of carbonates as a function of temperature.

COMPUTERIZED SHAWNEE LIME/LIMESTONE SCRUBBING MODEL USERS MANUAL

EPA Science Inventory

The manual gives a general description of a computerized model for estimating design and cost of lime or limestone scrubber systems for flue gas desulfurization (FGD). It supplements PB80-123037 by extending the number of scrubber options which can be evaluated. It includes spray...

Resource recycling technique of abandoned TNT-RDX-AL mixed explosive

NASA Astrophysics Data System (ADS)

Chen, Siyang; Ding, Yukui

2017-08-01

TNT-RDX-AL mixed explosive is a kind of high energy mixed explosive. It has the detonation characteristics even when reaching the scrapping standard. Inappropriate disposal often causes serious accident. Employing the resource recycling technique, the abandoned TNT-RDX-AL mixed explosive can be recycled. This paper summarized the progress of recycling of abandoned mixed explosive. What's more, three kinds of technological process of resource recycling abandoned TNT-RDX-AL mixed explosives are introduced. The author analysis of the current recovery processes and provided a reference for the recycling of the other same type explosive.

Nitrogen utilization and digestibility of amino acids by lambs fed a high-concentrate diet with limestone or magnesium oxide.

PubMed

Christiansen, M L; Webb, K E

1990-07-01

Effects were evaluated of high dietary levels of magnesium oxide (MgO) or limestone on DM, OM and CP digestibility, N balance and intestinal absorption of amino acids by lambs fed a high concentrate diet. Twelve wether lambs equipped with abomasal and ileal cannulas were blocked by weight and breeding and allotted to treatments in a randomized block design in two consecutive trials. Diets were control (800 g), control plus 1.5% MgO (812 g), control plus 1.5% limestone (812 g) and control plus 3.0% limestone (824 g) fed in two equal portions at 12-h intervals. Ruminal fluid pH differences were small. The pH of ileal digesta was greater (P less than .05) with MgO than with limestone (8.23 vs 7.73). Fecal pH was higher (P less than .01) for lambs fed all mineral treatments (avg 8.75) than for lambs fed the control (7.61) and was higher (P less than .01) when MgO (9.53) rather than limestone (8.36) was fed. Ruminal NH3N was lower (P less than .01) when lambs were fed MgO (11.9 mg/dl) compared with limestone (avg 31.2 mg/dl). Preintestinal DM digestibility was greatest (P less than .10) with limestone (avg 49.5%) feeding compared with feeding MgO (31.2%) or the control (35.4%). About 41.5% more essential (P less than .05) and 48% more nonessential (P less than .03) amino acids reached the small intestine when MgO was fed than when limestone was fed. Partial digestibility of amino acids in the small intestine was reduced (P less than .03) an average of 5 percentage units when MgO or limestone was fed. Feeding high levels of MgO or limestone to lambs did not improve the overall digestibility of DM, OM or CP. In fact, feeding high levels of MgO or limestone appeared to be detrimental, reducing intestinal absorption of amino acids.

Numerical Simulation of Abandoned Gob Methane Drainage through Surface Vertical Wells

PubMed Central

Hu, Guozhong

2015-01-01

The influence of the ventilation system on the abandoned gob weakens, so the gas seepage characteristics in the abandoned gob are significantly different from those in a normal mining gob. In connection with this, this study physically simulated the movement of overlying rock strata. A spatial distribution function for gob permeability was derived. A numerical model using FLUENT for abandoned gob methane drainage through surface wells was established, and the derived spatial distribution function for gob permeability was imported into the numerical model. The control range of surface wells, flow patterns and distribution rules for static pressure in the abandoned gob under different well locations were determined using the calculated results from the numerical model. PMID:25955438

Design and performance of limestone drains to increase pH and remove metals from acidic mine drainage, Chapter 2

USGS Publications Warehouse

Cravotta,, Charles A.; Watzlaf, George R.

2002-01-01

Data on the construction characteristics and the composition of influent and effluent at 13 underground, limestone-filled drains in Pennsylvania and Maryland are reported to evaluate the design and performance of limestone drains for the attenuation of acidity and dissolved metals in acidic mine drainage. On the basis of the initial mass of limestone, dimensions of the drains, and average flow rates, the initial porosity and average detention time for each drain were computed. Calculated porosity ranged from 0.12 to 0.50 with corresponding detention times at average flow from 1.3 to 33 h. The effectiveness of treatment was dependent on influent chemistry, detention time, and limestone purity. At two sites where influent contained elevated dissolved Al (>5 mg/liter), drain performance declined rapidly; elsewhere the drains consistently produced near-neutral effluent, even when influent contained small concentrations of dissolved Fe^+ (<5 mg/liter). Rates of limestone dissolution computed on the basis of average long-term Ca ion flux normalized by initial mass and purity of limestone at each of the drains ranged from 0.008 to 0.079 year-1. Data for alkalinity concentration and flux during 11-day closed-container tests using an initial mass of 4kg crushed limestone and a solution volume of 2.3 liter yielded dissolution rate constants that were comparable to these long-term field rates. An analytical method is proposed using closed-container test data to evaluate long-term performance (longevity) or to estimate the mass of limestone needed for a limestone treatment. This method condisers flow rate, influent alkalinity, steady-state alkalinity of effluent, and desired effluent alkalinity or detention time at a future time(s) and aplies first-order rate laws for limestone dissolution (continuous) and production of alkalinity (bounded).

Interactions between abundant fungal species influence the fungal community assemblage on limestone

PubMed Central

Morón-Ríos, Alejandro; Ortega-Morales, Benjamin Otto; De la Rosa-García, Susana; Partida-Martínez, Laila Pamela; Quintana, Patricia; Alayón-Gamboa, José Armando; Cappello-García, Silvia; González-Gómez, Santiago

2017-01-01

The assembly of fungal communities on stone materials is mainly influenced by the differential bioreceptivity of such materials and environmental conditions. However, little is known about the role of fungal interactions in the colonization and establishment of fungal species. We analyzed the effects of intra- and interspecific interactions between 11 species of fungi in oligotrophic and copiotrophic media and on limestone coupons. In a previous study, these species were the most frequently isolated in the epilithic biofilms of limestone walls exposed to a subtropical climate. In the culture media, we found a greater frequency of intra- and interspecific inhibitory effects in the oligotrophic medium than in the copiotrophic medium. On the limestone coupons, all fungi were able to establish; however, the colonization success rate varied significantly. Cladosporium cladosporioides had a less extensive colonization in isolation (control) than in dual interactions (coexistence) with other species. Phoma eupyrena exhibited the highest colonization success rate and competitive dominance among all tested species. X-ray diffraction (XRD) and scanning electron microscope (SEM) analyses revealed that Pestalotiopsis maculans and Paraconiothyrium sp. produced calcium oxalate crystals during their growth on coupon surfaces, both in isolation and in dual interactions. Our results demonstrate that interactions between abundant fungal species influence the fungal colonization on substrates, the biomineralization and the fungal community assemblage growing in limestone biofilms. PMID:29211748

Conceptualization of flow and transport in a limestone aquifer by multiple dedicated hydraulic and tracer tests

NASA Astrophysics Data System (ADS)

Mosthaf, Klaus; Brauns, Bentje; Fjordbøge, Annika S.; Rohde, Magnus M.; Kerrn-Jespersen, Henriette; Bjerg, Poul L.; Binning, Philip J.; Broholm, Mette M.

2018-06-01

Limestone aquifers are of great interest as a drinking water resource in many countries. They often have a complex crushed and fractured geology, which makes the analysis and description of flow and transport processes in such aquifers a challenging task. In this study, the solute transport behavior including fracture-matrix interaction in hydrogeological units of a limestone aquifer in eastern Denmark was characterized by designing, conducting and interpreting six depth-specific tracer tests involving natural- and forced-gradient conditions with multiple tracers representing different diffusion properties. To determine flow parameters, the tracer tests were complemented by a comprehensive set of depth-specific borehole and hydraulic tests. Based on the tests, a new and stronger conceptual understanding was developed for the different aquifer units. The investigated limestone aquifer is composed of a glacially crushed unit and two fractured units, with calcarenitic and bryozoan limestone of similar hydraulic properties. Hydraulic tests revealed that the crushed unit has a lower hydraulic conductivity than the fractured limestone units, likely due to the crushed conditions with small limestone clusters and small-aperture fractures potentially filled with fine material. In the fractured limestone units, a distinct preferential flow and primary transport along major horizontal fractures was inferred from the tracer tests under forced-gradient conditions. The dominant horizontal fractures were identified on impeller flow logs and appear connected between wells, having an extent of up to several hundred meters. Connectivity between the aquifer units was investigated with a long-term pumping test and tracer tests, revealing restricted vertical flow and transport. A very pronounced hydraulic conductivity contrast between major fractures and matrix could also be inferred from the borehole and hydraulic tests, which is consistent with the findings from the tracer tests. The

Subsurface stratigraphy and oil fields in the Salem Limestone and associated rocks in Indiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keller, S.J.; Becker, L.E.

An area of 11 counties in southwestern Indiana was studied because (1) the subsurface geology of the Salem Limestone and associated rocks in the area contained numerous correlation discrepancies; (2) it was the locus of recent oil exploration and oil discoveries in these rocks; (3) the last subsurface study of this rock section was made in 1957; and (4) since that time, subsurface data from newly drilled petroleum-test wells have increased a hundredfold. Because of their abundance, geophysical logs were used extensively for correlation. Drill cuttings, where available, were also used in studying the rock units. The upper boundary ofmore » the Salem was based on geophysical-log correlations as supported by available drill cuttings. The lower boundary of the Salem was based on drill cuttings. Commercial oil is produced from porous calcarenite zones in the St. Louis and Salem Limestones and from coarsely crystalline limestone in the Harrodsburg Limestone. The lower part of the St. Louis Limestone yields oil from a porous carbonate rock that resembles Salem calcarenite and that we have formally named the Sission Member in the St. Louis. The Salem calcarenite facies ranges in thickness from a low of 10 percent of the total Salem in the southern part of the study area to a high of 80 percent in the northern part. Oil is produced from porous zones in the calcarenite. Oil production from the St. Louis, Salem, and Harrodsburg Limestones in Indiana amounted to 8,880,078 barrels as of December 31, 1978. Production in 1977 was 1,534,320 barrels, and production in 1978 was 1,157,450 barrels. About 80 percent of the 1977 and 1978 production came from Union-Bowman Consolidated and Sisson Fields in Gibson, Knox, and Pike counties and the Owensville North Consolidated and Mt. Carmel Consolidated Fields in Gibson County. 15 figures, 3 tables.« less

Mineralogical characterization of the Shelburne Marble and the Salem limestone: Test stones used to study the effects of acid rain

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGee, E.S.

The Salem Limestone and the Shelburne Marble are representative of limestones and marbles commonly used in buildings and monuments. Both stones are composed predominantly of calcite. The Salem Limestone is homogeneous in composition and mineralogic characteristics throughout the test block. The Shelburne Marble has compositionally homogeneous mineral phases, but the distribution of those phases within the test block is random. The mineralogy and physical characteristics of the Shelburne Marble and Salem Limestone test blocks described in the study provide a baseline for future studies of the weathering behavior of these stones. Because the Shelburne Marble and the Salem Limestone aremore » representative of typical commercial marbles and limestones, they are likely to be useful in a consortium study of the effects of acid precipitation on these two types of building stones.« less

Detecting abandoned objects using interacting multiple models

NASA Astrophysics Data System (ADS)

Becker, Stefan; Münch, David; Kieritz, Hilke; Hübner, Wolfgang; Arens, Michael

2015-10-01

In recent years, the wide use of video surveillance systems has caused an enormous increase in the amount of data that has to be stored, monitored, and processed. As a consequence, it is crucial to support human operators with automated surveillance applications. Towards this end an intelligent video analysis module for real-time alerting in case of abandoned objects in public spaces is proposed. The overall processing pipeline consists of two major parts. First, person motion is modeled using an Interacting Multiple Model (IMM) filter. The IMM filter estimates the state of a person according to a finite-state, discrete-time Markov chain. Second, the location of persons that stay at a fixed position defines a region of interest, in which a nonparametric background model with dynamic per-pixel state variables identifies abandoned objects. In case of a detected abandoned object, an alarm event is triggered. The effectiveness of the proposed system is evaluated on the PETS 2006 dataset and the i-Lids dataset, both reflecting prototypical surveillance scenarios.

Abandonment of newborn infants: a Danish forensic medical survey 1997-2008.

PubMed

Gheorghe, Alexandra; Banner, Jytte; Hansen, Steen Holger; Stolborg, Uffe; Lynnerup, Niels

2011-12-01

Concealment of pregnancy and newborn infant abandonment are closely associated with neonaticide, the killing of an infant within the first 24 h of life or less than 28-30 days depending on the jurisdiction. Abandonment of newborn infants occurs throughout the world and often the outcome for the infant is death. Together with neonaticide it is felt to be one of the least preventable crimes. In this retrospective study we present all forensically known Danish cases of abandoned newborn infant corpses, covering the period from 1997 to 2008. Eleven newborn infant corpses were found; we registered characteristics of the newborn infants and the circumstances of the cases based on autopsy reports. One further newborn infant was included, dating back to 1992, as it was found to be connected with one of the later cases. The mean age of the women who abandoned their newborn infants was 22 years, and five of the autopsied newborn infants were probably alive when abandoned. In two cases the newborn infants were half siblings and abandoned by the same mother. The time span from abandonment to when the newborn infant was found ranged from hours to 7 years. Two-thirds of the newborn infants were girls (66.6%). The most common means of disposal was in a plastic bag (~60%); only one newborn infant was wearing clothes when found. Causes of death were usually given as asphyxia, brain injury or simply undetermined. Two-thirds of the newborn infants showed signs of violence. None of the newborn infants had congenital malformations.

Optimization of nanolime solvent for the consolidation of coarse porous limestone

NASA Astrophysics Data System (ADS)

Borsoi, Giovanni; Lubelli, Barbara; van Hees, Rob; Veiga, Rosário; Silva, António Santos

2016-09-01

The potentialities of nanomaterials for application in the field of conservation have been widely investigated in the last two decades. Among nanomaterials, nanolimes, i.e., dispersions of lime nanoparticles in alcohols are promising consolidating products for calcareous materials. Nanolimes are effective in recovering the very superficial loss of cohesion of decayed materials, but they do not always provide sufficient mass consolidation. This limitation is mainly related to the deposition of the nanoparticles nearby the surface of the material. Experimental research has been set up with the aim of improving the in-depth deposition of lime nanoparticles. Previous research by the authors has shown that nanolime deposition within a substrate can be controlled by adapting the nanolimes properties (kinetic stability and evaporation rate) to the moisture transport behavior of the substrate. Nanolime properties can be modified by the use of different solvents. In this research, nanolime dispersions have been further optimized for application on Maastricht limestone, a coarse porous limestone. Firstly, nanolimes were synthesized and dispersed in ethanol and/or water, both pure and mixed in different percentages. Subsequently, based on the kinetic stability of the nanolime dispersions, the most promising solvent mixtures were selected and applied on the limestone. The deposition of lime nanoparticles within the limestone was studied by phenolphthalein test, optical microscopy and scanning electron microscopy. The results confirm that nanolime dispersed in a mixture of ethanol (95 %) and water (5 %) can guarantee a better nanoparticles in-depth deposition within coarse porous substrates, when compared to dispersions in pure ethanol.

Quantification of Methane Leaks from Abandoned Oil and Gas Wells in California

NASA Astrophysics Data System (ADS)

Lebel, E.; Kang, M.; Lu, H.; Jackson, R. B.

2016-12-01

Abandoned oil and gas wells can provide a pathway for subterranean methane and other gases to be emitted to the atmosphere. However, abandoned wells are unaccounted for in greenhouse gas emissions inventories. While relatively little is known about abandoned wells, previous studies have shown that emissions from abandoned wells contribute approximately 4-7% of anthropogenic methane emissions in Pennsylvania (Kang et al. 2014) and <1% of regional methane emissions in oil and gas producing regions of Colorado, Utah, Ohio, and Wyoming (Townsend-Small et al. 2015). Another study (Boothroyd et al. 2016) has shown that 30% of abandoned wells in the UK have a positive surface methane flux. California has a long history of oil and gas production, beginning from the 1860s, and currently ranks third in oil production by state. As a result, there are more than 100,000 wells across the state. Our study uses static flux chambers to measure individual abandoned wells in California to estimate state-wide methane emissions from these wells. In addition to measuring methane concentrations, we measure ethane, propane, isobutane, n-butane, and 13-CH4 to understand whether this methane has a biogenic or thermogenic source. We hope that our research will determine whether or not abandoned oil and gas wells are a significant source of anthropogenic methane emissions in California. Our results along with measurements in other parts of the United States can be used to scale up methane emission estimates to the national level, accounting for the millions of abandoned wells in the country.

Geology, Ground-Water Occurrence, and Estimated Well Yields from the Mariana Limestone, Kagman Area, Saipan, Commonwealth of the Northern Mariana Islands

USGS Publications Warehouse

Hoffmann, John P.; Carruth, Rob; Meyer, William

1998-01-01

A study of the geology, ground-water occurrence, and estimated well yields from the Mariana Limestone was done to investigate ground-water availability in the Kagman area, Saipan. The Mariana and Tagpochau Limestone formations form the major aquifer in the Kagman drainage basin. The Mariana Limestone, which is the major water-bearing unit in the Kagman area, ranges in thickness from 300 to 500 feet and contains intermittent, thin clay stringers. The calcareous rocks of the Tagpochau Limestone range in thickness from 500 to 1,000 feet and are more sandy than those of the Mariana Limestone. Ground water is unconfined in the Mariana Limestone and ranges from unconfined to confined in the Tagpochau Limestone. The fresh ground-water lens (that part of the lens with less than 2-percent of the chloride-ion concentration in seawater) in the Mariana Limestone is relatively thin, ranging from about 15 to 21 feet. Altitude of the water table ranges from about 1.5 to 2.5 feet above mean sea level. Freshwater in the Mariana Limestone is underlain by seawater and is separated by a transition zone about 8 to 25 feet thick. Hydraulic conductivity and transmissivity of the Mariana Limestone were calculated from data collected at six test wells. Using the Newman method, estimated hydraulic conductivity and transmissivity range from 290 to 2,500 feet per day and 7,600 to 62,000 feet squared per day, respectively. The higher values probably are indicative of average conditions in the Mariana Limestone. The estimated storage coefficient of the Mariana Limestone is about 0.1. The availability of water from the Mariana Limestone is restricted by the thinness of the freshwater lens. Results of the study indicate that fresh ground water can be obtained from the Mariana Limestone when wells are designed for minimum drawdown, effectively skimming freshwater from the top of the lens. Wells that are shallow, widely spaced, and pumped at low uniform rates can prevent saltwater intrusion

Epilithic and endolithic bacterial communities in limestone from a Maya archaeological site.

PubMed

McNamara, Christopher J; Perry, Thomas D; Bearce, Kristen A; Hernandez-Duque, Guillermo; Mitchell, Ralph

2006-01-01

Biodeterioration of archaeological sites and historic buildings is a major concern for conservators, archaeologists, and scientists involved in preservation of the world's cultural heritage. The Maya archaeological sites in southern Mexico, some of the most important cultural artifacts in the Western Hemisphere, are constructed of limestone. High temperature and humidity have resulted in substantial microbial growth on stone surfaces at many of the sites. Despite the porous nature of limestone and the common occurrence of endolithic microorganisms in many habitats, little is known about the microbial flora living inside the stone. We found a large endolithic bacterial community in limestone from the interior of the Maya archaeological site Ek' Balam. Analysis of 16S rDNA clones demonstrated disparate communities (endolithic: >80% Actinobacteria, Acidobacteria, and Low GC Firmicutes; epilithic: >50% Proteobacteria). The presence of differing epilithic and endolithic bacterial communities may be a significant factor for conservation of stone cultural heritage materials and quantitative prediction of carbonate weathering.

OPTIMIZATION OF A PULSED LIMESTONE BED REACTOR AT THE ARGO TUNNEL IN IDAHO SPRINGS, COLORADO

EPA Science Inventory

Acid Mine Drainage (AMD) is an unintended consequence of coal and metal mining that adversely affects thousands of miles of streams both in the eastern and western regions of the U.S. A novel AMD treatment process based on limestone based on limestone neutralization has been dev...

Experimental study on the strength parameter of Quarry Dust mixed Coconut Shell Concrete adding Coconut Fibre

NASA Astrophysics Data System (ADS)

Matangulu Shrestha, Victor; Anandh, S.; Sindhu Nachiar, S.

2017-07-01

Concrete is a heterogeneous mixture constitute of cement as the main ingredient with a different mix of fine and coarse aggregate. The massive use of conventional concrete has a shortfall in its key ingredients, natural sand and coarse aggregate, due to increased industrialisation and globalisation. To overcome the shortage of material, an alternate material with similar mechanical properties and composition has to be studied, as replacement of conventional concrete. Coconut shell concrete is a prime option as replacement of key ingredients of conventional concrete as coconut is produced in massive quantity in south East Asia. Coconut shell concrete is lightweight concrete and different research is still ongoing concerning about its mix design and composition in the construction industry. Concrete is weak in tension as compared to compression, hence the fibre is used to refrain the crack in the concrete. Coconut fibre is one of many fibres which can be used in concrete. The main aim of this project is to analyse the use of natural by-products in the construction industry, make light weight concrete and eco-friendly construction. This project concerns with the comparison of the mechanical properties of coconut shell concrete and conventional concrete, replacing fine aggregate with quarry dust using coconut fibre. M25 grade of concrete was adopted and testing of concrete was done at the age of 3, 7 and 28 days. In this concrete mix, sand was replaced completely in volumetric measurement by quarry dust. The result was analysed and compared with addition of coconut fibre at varying percentage of 1%, 2%, 3%, 4% and 5%. From the test conducted, coconut shell concrete with quarry dust has the maximum value at 4% of coconut fibre while conventional concrete showed the maximum value at 2% of coconut fibre.

41 CFR 109-45.902-2 - Abandonment or destruction without notice.

Code of Federal Regulations, 2010 CFR

2010-07-01

... UTILIZATION AND DISPOSAL 45-SALE, ABANDONMENT, OR DESTRUCTION OF PERSONAL PROPERTY 45.9-Abandonment or... destruction without public notice of personal property. The OPMO shall review and coordinate on the findings. ...

Factors associated with abandonment of therapy by children diagnosed with solid tumors in Peru.

PubMed

Vasquez, Liliana; Diaz, Rosdali; Chavez, Sharon; Tarrillo, Fanny; Maza, Ivan; Hernandez, Eddy; Oscanoa, Monica; García, Juan; Geronimo, Jenny; Rossell, Nuria

2018-06-01

Abandonment of treatment is a major cause of treatment failure and poor survival in children with cancer in low- and middle-income countries. The incidence of treatment abandonment in Peru has not been reported. The aim of this study was to examine the prevalence of and factors associated with treatment abandonment by pediatric patients with solid tumors in Peru. We retrospectively reviewed the sociodemographic and clinical data of children referred between January 2012 and December 2014 to the two main tertiary centers for childhood cancer in Peru. The definition of treatment abandonment followed the International Society of Paediatric Oncology, Paediatric Oncology in Developing Countries, Abandonment of Treatment recommendation. Data from 1135 children diagnosed with malignant solid tumors were analyzed, of which 209 (18.4%) abandoned treatment. Bivariate logistic regression analysis showed significantly higher abandonment rates in children living outside the capital city, Lima (forest; odds ratio [OR] 3.25; P < 0.001), those living in a rural setting (OR 3.44; P < 0.001), and those whose parent(s) lacked formal employment (OR 4.39; P = 0.001). According to cancer diagnosis, children with retinoblastoma were more likely to abandon treatment compared to children with other solid tumors (OR 1.79; P = 0.02). In multivariate regression analyses, rural origin (OR 2.02; P = 0.001) and lack of formal parental employment (OR 2.88; P = 0.001) were independently predictive of abandonment. Treatment abandonment prevalence of solid tumors in Peru is high and closely related to sociodemographical factors. Treatment outcomes could be substantially improved by strategies that help prevent abandonment of therapy based on these results. © 2018 Wiley Periodicals, Inc.

Ramp sedimentation in the Dinantian limestones of the Shannon Trough, Co. Limerick, Ireland

NASA Astrophysics Data System (ADS)

Somerville, Ian D.; Strogen, Peter

1992-08-01

During the late Chadian and Arundian (Lower Carboniferous), an extensive carbonate ramp (Limerick Ramp) developed over County Limerick, southwest Ireland, dipping northwestwards. Three distinct facies can be recognised corresponding to position on this ramp: inner, mid- and outer ramp. The inner ramp facies of oolitic and crinoidal grainstones (Herbertstown Limestone Formation) in east Limerick formed a major shoal behind which peritidal limestones were deposited. The mid-ramp facies of muddy bioclastic limestones and shales (Cooperhill facies) in north Limerick formed between fairweather and storm wave bases. The outer ramp (basinal) facies of mudstones and thin graded resedimented limestones (Rathkeale Beds) in west Limerick developed below storm wave base when fine terrigenous input was high. Later in the Arundian there was progradation of the nearshore oolitic and crinoidal grainstones over the mid-ramp facies. By the Holkerian, the deep-water basinal facies in west Limerick was buried beneath mid-ramp facies (Durnish Limestone). The initiation of the Limerick Ramp is closely related to the formation of the Shannon Trough. In the late Courceyan, accelerated subsidence in the Shannon area during deposition of Waulsortian facies marked the onset of a sag phase. Following a quiescent period in early Chadian, subsidence was renewed in the late Chadian and Arundian, when major facies changes occurred on the ramp. Comparison of the Shannon Trough with the Dublin Basin shows that in the latter, tectonic events in the Chadian and Arundian, particularly syn-sedimentary faulting, created a sharp division between platform and basinal sedimentation. Such tectonic influence is not recognised in the Shannon Trough. Here differential subsidence and eustatic sea-level changes led to more permanent ramp existence, modified only by westwards progradation.

Effects of limestone petrography and calcite microstructure on OPC clinker raw meals burnability

NASA Astrophysics Data System (ADS)

Galimberti, Matteo; Marinoni, Nicoletta; Della Porta, Giovanna; Marchi, Maurizio; Dapiaggi, Monica

2017-10-01

Limestone represents the main raw material for ordinary Portland cement clinker production. In this study eight natural limestones from different geological environments were chosen to prepare raw meals for clinker manufacturing, aiming to define a parameter controlling the burnability. First, limestones were characterized by X-Ray Fluorescence, X-Ray Powder Diffraction and Optical Microscopy to assess their suitability for clinker production and their petrographic features. The average domains size and the microstrain of calcite were also determined by X-Ray Powder Diffraction line profile analysis. Then, each limestone was admixed with clay minerals to achieve the adequate chemical composition for clinker production. Raw meals were thermally threated at seven different temperatures, from 1000 to 1450 °C, to evaluate their behaviour on heating by ex situ X-Ray Powder Diffraction and to observe the final clinker morphology by Scanning Electron Microscopy. Results indicate the calcite microstrain is a reliable parameter to predict the burnability of the raw meals, in terms of calcium silicates growth and lime consumption. In particular, mixtures prepared starting from high-strained calcite exhibit a better burnability. Later, when the melt appears this correlation vanishes; however differences in the early burnability still reflect on the final clinker composition and texture.

The Biot coefficient for a low permeability heterogeneous limestone

NASA Astrophysics Data System (ADS)

Selvadurai, A. P. S.

2018-04-01

This paper presents the experimental and theoretical developments used to estimate the Biot coefficient for the heterogeneous Cobourg Limestone, which is characterized by its very low permeability. The coefficient forms an important component of the Biot poroelastic model that is used to examine coupled hydro-mechanical and thermo-hydro-mechanical processes in the fluid-saturated Cobourg Limestone. The constraints imposed by both the heterogeneous fabric and its extremely low intact permeability [K \\in (10^{-23},10^{-20}) m2 ] require the development of alternative approaches to estimate the Biot coefficient. Large specimen bench-scale triaxial tests (150 mm diameter and 300 mm long) that account for the scale of the heterogeneous fabric are complemented by results for the volume fraction-based mineralogical composition derived from XRD measurements. The compressibility of the solid phase is based on theoretical developments proposed in the mechanics of multi-phasic elastic materials. An appeal to the theory of multi-phasic elastic solids is the only feasible approach for examining the compressibility of the solid phase. The presence of a number of mineral species necessitates the use of the theories of Voigt, Reuss and Hill along with the theories proposed by Hashin and Shtrikman for developing bounds for the compressibility of the multi-phasic geologic material composing the skeletal fabric. The analytical estimates for the Biot coefficient for the Cobourg Limestone are compared with results for similar low permeability rocks reported in the literature.

Book review: old fields: dynamics and restoration of abandoned farmland

USDA-ARS?s Scientific Manuscript database

The 2007 volume, “Old Fields: Dynamics and Restoration of Abandoned Farmland”, edited by VA Cramer and RJ Hobbs and published by the Society for Ecological Restoration International (Island Press), is a valuable attempt to synthesize a dozen case studies on agricultural abandonment from all of the ...

40 CFR 144.62 - Cost estimate for plugging and abandonment.

Code of Federal Regulations, 2011 CFR

2011-07-01

... must revise the plugging and abandonment cost estimate whenever a change in the plugging and... 40 Protection of Environment 23 2011-07-01 2011-07-01 false Cost estimate for plugging and abandonment. 144.62 Section 144.62 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER...

Two new Phlegmariurus species (Lycopodiaceae) and one new combination from Peninsular Malaysia.

PubMed

Kiew, Ruth; Kamin, Imin

2018-01-01

Two new species, Phlegmariurus iminii Kiew (Lycopodiaceae) from limestone karst and P. monticola Kiew from montane habitats, are described from Peninsular Malaysia and a new combination is made for Phlegmariurus pinifolius (Trevis.) Kiew. Phlegmariurus iminii , known from a single hill threatened by quarrying, is Critically Endangered; while P. monticola and P. pinifolius that are relatively widespread are of Least Concern.

Fluorspar

USGS Publications Warehouse

Miller, M.

2012-01-01

World fluorspar demand continued to show signs of recovery from 2008-2009 recession. In 2011, nearly all fluorspar (CaF2) consumed in the United States was imported. Hastie Mining and Trucking Co. produced some fluorspar as a byproduct from its limestone quarry operations in Illinois. In addition, a small amount of usable synthetic fluorspar was produced from industrial waste streams.

Ultrasonic characterization of granites obtained from industrial quarries of Extremadura (Spain).

PubMed

del Río, L M; López, F; Esteban, F J; Tejado, J J; Mota, M; González, I; San Emeterio, J L; Ramos, A

2006-12-22

The industry of ornamental rocks, such as granites, represents one of the most important industrial activities in the region of Extremadura, SW Spain. A detailed knowledge of the intrinsic properties of this natural stone and its environmental evolution is a required goal in order to fully characterize its quality. In this work, two independent NDT acoustic techniques have been used to measure the acoustic velocity of longitudinal waves in different prismatic granitic-samples of industrial quarries. A low-frequency transceiver set-up, based on a high-voltage BPV Steinkamp instrument and two 50 kHz probes, has been used to measure pulse travel times by ultrasonic through-transmission testing. In complementary fashion, an Erudite MK3 test equipment with an electromagnetic vibrator and two piezoelectric sensors has also been employed to measure ultrasonic velocity by means of a resonance-based method, using the same types of granite varieties. In addition, a comprehensive set of physical/mechanical properties have also been analyzed, according to Spanish regulations in force, by means of alternative methods including destructive techniques such as strength, porosity, absorption, etc. A large number of samples, representing the most important varieties of granites from quarries of Extremadura, have been analyzed using the above-mentioned procedures. Some results obtained by destructive techniques have been correlated with those found using ultrasonic techniques. Our experimental setting allowed a complementary characterization of granite samples and a thorough validation of the different techniques employed, thus providing the industry of ornamental rocks with a non-destructive tool that will facilitate a more detailed insight on the properties of the rocks under study.

76 FR 1211 - Union Pacific Railroad Company-Abandonment Exemption-In Wright County, IA

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-07

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. AB 33 (Sub-No. 293X)] Union Pacific Railroad Company--Abandonment Exemption--In Wright County, IA Union Pacific Railroad Company (UP) filed a verified notice of exemption under 49 CFR 1152 subpart F--Exempt Abandonments to abandon a line...

The global potential of bioenergy on abandoned agriculture lands.

PubMed

Campbell, J Elliott; Lobell, David B; Genova, Robert C; Field, Christopher B

2008-08-01

Converting forest lands into bioenergy agriculture could accelerate climate change by emitting carbon stored in forests, while converting food agriculture lands into bioenergy agriculture could threaten food security. Both problems are potentially avoided by using abandoned agriculture lands for bioenergy agriculture. Here we show the global potential for bioenergy on abandoned agriculture lands to be less than 8% of current primary energy demand, based on historical land use data, satellite-derived land cover data, and global ecosystem modeling. The estimated global area of abandoned agriculture is 385-472 million hectares, or 66-110% of the areas reported in previous preliminary assessments. The area-weighted mean production of above-ground biomass is 4.3 tons ha(-1) y(-1), in contrast to estimates of up to 10 tons ha(-1) y(-1) in previous assessments. The energy content of potential biomass grown on 100% of abandoned agriculture lands is less than 10% of primary energy demand for most nations in North America, Europe, and Asia, but it represents many times the energy demand in some African nations where grasslands are relatively productive and current energy demand is low.

75 FR 65047 - Union Pacific Railroad Company-Abandonment Exemption-in Pulaski County, AR

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-21

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. AB 33 (Sub-No. 289X)] Union Pacific Railroad Company--Abandonment Exemption--in Pulaski County, AR Union Pacific Railroad Company (UP) filed a verified notice of exemption under 49 CFR part 1152 subpart F-Exempt Abandonments to abandon a 4...

Risk Factors For Abandonment of Wilms Tumor Therapy in Kenya

PubMed Central

Libes, Jaime; Oruko, Oliver; Abdallah, Fatmah; Githanga, Jessie; Ndung’u, James; Musimbi, Joyce; Njuguna, Festus; Patel, Kirtika; White, John; Axt, Jason R.; O’Neill, James A.; Shrubsole, Martha; Li, Ming; Lovvorn, Harold N.

2014-01-01

Background Survival from Wilms tumor (WT) in sub-Saharan Africa remains dismal as a result of on-therapy mortality and treatment abandonment. Review of patients diagnosed from 2008–2011 in our Kenyan Wilms Tumor Registry showed a loss to follow up (LTFU) rate approaching 50 percent. The purpose of this study was to trace those LTFU, estimate the survival rate, and identify risk factors for treatment abandonment. Procedure We administered a comprehensive survey to parents of patients with WT at the two largest referral hospitals in Kenya to identify barriers to care. We also telephoned families who had abandoned care to determine vital status and identify risk factors for treatment abandonment. Results Of 136 registered patients, 77 were confirmed dead (56.7%), 38 remained alive (27.9%), and the vital status of 21 patients remains unknown (15.4%). After contacting 33 of the patients who either abandoned curative treatment (n=34) or did not attend off-therapy visits (n=20), the best estimate of 2-year overall survival of patients with WT in Kenya approaches 36%. Sixty-three percent of parents misunderstood treatment plans and 55% encountered financial barriers. When asked how to increase comfort with the child’s treatment, 27% of parents volunteered improving inefficient services and 26% volunteered reducing drug-unavailability. Conclusions Treatment abandonment remains a significant problem contributing to increased mortality from WT in developing countries. This multi-center survey identified the barriers to treatment completion from the parental perspective to be lack of education about WT and treatment, financial constraints, need for quality improvement, and drug-unavailability. PMID:25382257

Wind Power Potential at Abandoned Mines in Korea

NASA Astrophysics Data System (ADS)

jang, M.; Choi, Y.; Park, H.; Go, W.

2013-12-01

This study performed an assessment of wind power potential at abandoned mines in the Kangwon province by analyzing gross energy production, greenhouse gas emission reduction and economic effects estimated from a 600 kW wind turbine. Wind resources maps collected from the renewable energy data center in Korea Institute of Energy Research(KIER) were used to determine the average wind speed, temperature and atmospheric pressure at hub height(50 m) for each abandoned mine. RETScreen software developed by Natural Resources Canada(NRC) was utilized for the energy, emission and financial analyses of wind power systems. Based on the results from 5 representative mining sites, we could know that the average wind speed at hub height is the most critical factor for assessing the wind power potential. Finally, 47 abandoned mines that have the average wind speed faster than 6.5 m/s were analyzed, and top 10 mines were suggested as relatively favorable sites with high wind power potential in the Kangwon province.

Full-scale results for TAM limestone injection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baer, S.

1996-12-31

Information is outlined on the use of thermally active marble (TAM) sorbents in boilers. Data are presented on: the comparison of TAM to limestone; NOVACON process development history; CFB test history; CFB pilot scale test; full-scale CFB trial; August, 1996 CFB demonstration; Foster Wheeler Mount Carmel sorbent feed rate comparison and Ca:S comparison; unburned carbon is ash; and advantages and savings in CFB boilers.

SOX OUT ON A LIMB (LIMESTONE INJECTION MULTISTAGE BURNER)

EPA Science Inventory

The paper describes the most recent results from the Limestone Injection Multistage Burner (LIMB) program, covering results from the wall-fired demonstration. Tests were conducted to determine the efficacy of commercial calcium hydroxide (Ca(OH)2) and of calcium-lignosulfonate-mo...

Soil respiration patterns and controls in limestone cedar glades

USGS Publications Warehouse

Cartwright, Jennifer M.; Hui, Dafeng

2015-01-01

Soil depth, SOM, and vegetation cover were important drivers of Rs in limestone cedar glades. Seasonal Rs patterns reflected those for mesic temperate grasslands more than for semi-arid ecosystems, in that Rs primarily tracked temperature for most of the year.

1. SOUTH FACADE. CONSTRUCTED (ca. 1895) OF INDIGENOUS LIMESTONE AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. SOUTH FACADE. CONSTRUCTED (ca. 1895) OF INDIGENOUS LIMESTONE AND USED AS LOCKPORTS CENTRAL HIGH SCHOOL FOR MORE THAN SIXTY YEARS. - Lockport Historic District, Central High School, Lockport, Will County, IL

Abandoned mine drainage in the Swatara Creek Basin, southern anthracite coalfield, Pennsylvania, USA: 2. performance of treatment systems

USGS Publications Warehouse

Cravotta, Charles A.

2010-01-01

A variety of passive and semi-passive treatment systems were constructed by state and local agencies to neutralize acidic mine drainage (AMD) and reduce the transport of dissolved metals in the upper Swatara Creek Basin in the Southern Anthracite Coalfield in eastern Pennsylvania. To evaluate the effectiveness of selected treatment systems installed during 1995–2001, the US Geological Survey collected water-quality data at upstream and downstream locations relative to each system eight or more times annually for a minimum of 3 years at each site during 1996–2007. Performance was normalized among treatment types by dividing the acid load removed by the size of the treatment system. For the limestone sand, open limestone channel, oxic limestone drain, anoxic limestone drain (ALD), and limestone diversion well treatment systems, the size was indicated by the total mass of limestone; for the aerobic wetland systems, the size was indicated by the total surface area of ponds and wetlands. Additionally, the approximate cost per tonne of acid treated over an assumed service life of 20 years was computed. On the basis of these performance metrics, the limestone sand, ALD, oxic limestone drain, and limestone diversion wells had similar ranges of acid-removal efficiency and cost efficiency. However, the open limestone channel had lower removal efficiency and higher cost per ton of acid treated. The wetlands effectively attenuated metals transport but were relatively expensive considering metrics that evaluated acid removal and cost efficiency. Although the water-quality data indicated that all treatments reduced the acidity load from AMD, the ALD was most effective at producing near-neutral pH and attenuating acidity and dissolved metals. The diversion wells were effective at removing acidity and increasing pH of downstream water and exhibited unique potential to treat moderate to high flows associated with storm flow conditions.

The effect of stress on limestone permeability and its effective stress behavior

NASA Astrophysics Data System (ADS)

Meng, F.; Baud, P.; Ge, H.; Wong, T. F.

2017-12-01

The evolution of permeability and its effective stress behavior is related to inelastic deformation and failure mode. This was investigated in Indiana and Purbeck limestones with porosities of 18% and 13%, respectively. Hydrostatic and triaxial compression tests were conducted at room temperature on water-saturated samples at pore pressure of 5 MPa and confining pressures up to 90 MPa. Permeability was measured using steady flow at different stages of deformation. For Indiana limestone, under hydrostatic loading pore collapse initiated at critical pressure P* 55 MPa with an accelerated reduction of permeability by 1/2. At a confinement of 35 MPa and above, shear-enhanced compaction initiated at critical stress C*, beyond which permeability reduction up to a factor of 3 was observed. At a confinement of 15 MPa and below, dilatancy initiated at critical stress C', beyond which permeability continued to decrease, with a negative correlation between porosity and permeability changes. Purbeck limestone showed similar evolution of permeability. Microstructural and mercury porosimetry data showed that pore size distribution in both Indiana and Purbeck limestones is bimodal, with significant proportions of macropores and micropores. The effective stress behaviour of a limestone with dual porosity is different from the prediction for a microscopically homogeneous assemblage, in that its effective stress coefficients for permeability and porosity change may attain values significantly >1. Indeed this was confirmed by our measurements (at confining pressures of 7-15 MPa and pore pressures of 1-3 MPa) in samples that had not been deformed inelastically. We also investigated the behavior in samples hydrostatically and triaxially compacted to beyond the critical stresses P* and C*, respectively. Experimental data for these samples consistently showed effective stress coefficients for both permeability and porosity change with values <1. Thus the effective stress behavior in an

Repeated use of an abandoned vehicle by nesting Turkey vultures (Cathartes aura)

USGS Publications Warehouse

Igl, L.D.; Peterson, S.L.

2010-01-01

Turkey Vultures (Cathartes aura) lay their eggs on an existing substrate in the dark recesses of a variety of natural sites (Kirk and Mossman 1998). Although an important requirement of Turkey Vulture nest-site selection is isolation from human disturbances (Kirk and Mossman 1998), their nests have been reported in abandoned buildings since at least the early 1800s (Nuttall 1832). Depopulation of rural areas in North America in recent decades has resulted in many abandoned buildings within the Turkey Vulture's breeding range (Peck 2003). Increased use of abandoned buildings by nesting Turkey Vultures has been implicated in the species' recent northward range expansion (Peck 2003, Nelson et al. 2005, Houston et al. 2007). Although abandoned or inoperative vehicles also are widespread in rural areas, we found no published literature documenting Turkey Vultures' use of these potential nest sites. Herein, we summarize the first documented incidence of a Turkey Vulture nesting in an abandoned vehicle.

Geologic framework and hydrogeologic characteristics of the Glen Rose limestone, Camp Stanley Storage Activity, Bexar County, Texas

USGS Publications Warehouse

Clark, Allan K.

2004-01-01

The Trinity aquifer is a regional water source in the Hill Country of south-central Texas that supplies water for agriculture, commercial, domestic, and stock purposes. Rocks of the Glen Rose Limestone, which compose the upper zone and upper part of the middle zone of the Trinity aquifer, crop out at the Camp Stanley Storage Activity (CSSA), a U.S. Army weapons and munitions supply, maintenance, and storage facility in northern Bexar County (San Antonio area) (fig. 1). On its northeastern, eastern, and southern boundaries, the CSSA abuts the Camp Bullis Training Site, a U.S. Army field training site for military and Federal government agencies. During 2003, the U.S. Geological Survey (USGS), in cooperation with the U.S. Army, studied the outcropping Glen Rose Limestone at the CSSA and immediately adjacent area (Camp Stanley study area, fig. 1) to identify and map the hydrogeologic subdivisions and faults of the Glen Rose Limestone at the facility. The results of the study are intended to help resource managers improve their understanding of the distribution of porosity and permeability of the outcropping rocks, and thus the conditions for recharge and the potential for contaminants to enter the Glen Rose Limestone. This study followed a similar study done by the USGS at Camp Bullis (Clark, 2003). The purpose of this report is to present the geologic framework and hydrogeologic characteristics of the Glen Rose Limestone in the study area. The hydrogeologic nomenclature follows that introduced by Clark (2003) for the outcropping Glen Rose Limestone at Camp Bullis in which the upper member of the Glen Rose Limestone (hereinafter, upper Glen Rose Limestone), which is coincident with the upper zone of the Trinity aquifer, is divided into five intervals on the basis of observed lithologic and hydrogeologic properties. An outcrop map, two generalized sections, related illustrations, and a table summarize the description of the framework and distribution of characteristics.

Use of limestone karst forests by Bornean orangutans (Pongo pygmaeus morio) in the Sangkulirang peninsula, east Kalimantan, Indonesia.

PubMed

Marshall, Andrew J; Salas, Leonardo A; Stephens, Suzette; Engström, Linda; Meijaard, Erik; Stanley, Scott A

2007-02-01

The Indonesian province of East Kalimantan is home to some of the largest remaining contiguous tracts of lowland Dipterocarp forest on the island of Borneo. Nest surveys recently conducted in these forests indicated the presence of a substantial population of Eastern Bornean orangutans (Pongo pygmaeus morio) in the Berau and East Kutai regencies in the northern half of the province. The Sangkulirang Peninsula contains extensive limestone karst forests in close proximity to the lowland Dipterocarp forests inhabited by orangutans in these regencies. Orangutans have been sighted in these limestone karst forests, but the importance of this forest type for orangutans has been unclear. Therefore, we conducted 49 km of nest surveys in limestone karst forest to obtain the first quantitative estimates of orangutan densities in this habitat, and walked 28 km of surveys in nearby lowland Dipterocarp forests for comparison. We also gathered basic ecological data along our transects in an attempt to identify correlates of orangutan abundance across these habitat types. Undisturbed limestone karst forests showed the lowest orangutan densities (147 nests/km(2), 0.82 indiv/km(2)), disturbed limestone forests had intermediate densities (301 nests/km(2), 1.40 indiv/km(2)), and undisturbed lowland Dipterocarp forests contained the highest density (987 nests/km(2), 5.25 indiv/km(2)), significantly more than the undisturbed limestone karst forests. This difference was not correlated with variation in liana abundance, fig stem density, or stump density (an index of forest disturbance). Therefore, other factors, such as the relatively low tree species diversity of limestone karst forests, may explain why orangutans appear to avoid these areas. We conclude that limestone karst forests are of low relevance for safeguarding the future of orangutans in East Kalimantan.

30 CFR 931.20 - Approval of the New Mexico abandoned mine reclamation plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Approval of the New Mexico abandoned mine..., DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE NEW MEXICO § 931.20 Approval of the New Mexico abandoned mine reclamation plan. The New Mexico Abandoned Mine...

78 FR 79726 - Norfolk Southern Railway Company-Abandonment Exemption-in Gaston County, NC

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-31

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. AB 290 (Sub-No. 339X)] Norfolk Southern Railway Company--Abandonment Exemption--in Gaston County, NC Norfolk Southern Railway Company (NSR) has filed a verified notice of exemption under 49 CFR part 1152 subpart F-Exempt Abandonments to abandon approximately 0.5 miles of rail...

30 CFR 931.20 - Approval of the New Mexico abandoned mine reclamation plan.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Approval of the New Mexico abandoned mine..., DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE NEW MEXICO § 931.20 Approval of the New Mexico abandoned mine reclamation plan. The New Mexico Abandoned Mine...

30 CFR 931.20 - Approval of the New Mexico abandoned mine reclamation plan.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Approval of the New Mexico abandoned mine..., DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE NEW MEXICO § 931.20 Approval of the New Mexico abandoned mine reclamation plan. The New Mexico Abandoned Mine...

30 CFR 931.20 - Approval of the New Mexico abandoned mine reclamation plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Approval of the New Mexico abandoned mine..., DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE NEW MEXICO § 931.20 Approval of the New Mexico abandoned mine reclamation plan. The New Mexico Abandoned Mine...

30 CFR 931.20 - Approval of the New Mexico abandoned mine reclamation plan.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Approval of the New Mexico abandoned mine..., DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE NEW MEXICO § 931.20 Approval of the New Mexico abandoned mine reclamation plan. The New Mexico Abandoned Mine...

Diagenetic evolution and stable isotopes of Lower Permian platform marginal carbonates (Trogkofel Limestone, Carnic Alps, Austria)

NASA Astrophysics Data System (ADS)

Schaffhauser, Maria; Krainer, Karl; Sanders, Diethard Gerald; Spötl, Christoph

2010-05-01

The Trogkofel massif in the Carnic Alps, Austria/Italy, consists of a succession up to 400 m thick of limestones deposited along a platform margin (Trogkofel Limestone; Artinskian). The top of the Trogkofel Limestone is erosively overlain by the Tarvis Breccia. Up-section, the Trogkofel Limestone consists of well-bedded shallow-water bioclastic limestones with intercalated mud mounds, overlain by thick-bedded to unbedded limestones (bioclastic grainstones, packstones, rudstones) and cementstone mounds rich in phylloid algae, Tubiphytes, bryozoans and Archaeolithoporella. In the cementstone mounds, bioclasts are coated by thick fringes and botryoids of fibrous calcite, and of calcite spar that probably represents calcitized aragonite. Primary and intrinsic pores are filled by microbialite, and/or by mudstone to bioclastic wackestone. Shallow-water bioclastic grainstones are cemented by isopachous fringes of fibrous calcite, or by sparry calcite. Throughout the succession, evidence for meteoric-vadose dissolution is present. The Trogkofel Limestone is riddled by palaeokarstic dykes and caverns filled by (a) isopachous cement fringes up to a few decimetres thick, and/or (b) by red, geopetally-laminated lime mudstone to bio-lithoclastic wackestone; geopetal laminasets locally display convolute bedding. Small dissolution cavities are filled by grey internal sediment, or by crystal silt. Brecciated internal sediments overlain by unbrecciated, geopetally-laminated infillings record deformation during or after deposition of the Trogkofel Limestone. Polyphase fractures cemented by calcite may cross-cut both internal sediments and host rock. In the Trogkofel Limestone, local dolomitization is common. Replacement dolomites show a wide range of shapes and fabrics, including: (a) fine-crystalline anhedral xenotopic fabric, (b) coarse-crystalline subhedral to euhedral, hypidiotopic to idiotopic fabric of turbid or optically zoned crystals, and (c) saddle dolomite as replacement

Hydrogen sulfide capture by limestone and dolomite at elevated pressure. 2: Sorbent particle conversion modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zevenhoven, C.A.P.; Yrjas, K.P.; Hupa, M.M.

1996-03-01

The physical structure of a limestone or dolomite to be used in in-bed sulfur capture in fluidized bed gasifiers has a great impact on the efficiency of sulfur capture and sorbent use. In this study an unreacted shrinking core model with variable effective diffusivity is applied to sulfidation test data from a pressurized thermogravimetric apparatus (P-TGA) for a set of physically and chemically different limestone and dolomite samples. The particle size was 250--300 {micro}m for all sorbents, which were characterized by chemical composition analysis, particle density measurement, mercury porosimetry, and BET internal surface measurement. Tests were done under typical conditionsmore » for a pressurized fluidized-bed gasifier, i.e., 20% CO{sub 2}, 950 C, 20 bar. At these conditions the limestone remains uncalcined, while the dolomite is half-calcined. Additional tests were done at low CO{sub 2} partial pressures, yielding calcined limestone and fully calcined dolomite. The generalized model allows for determination of values for the initial reaction rate and product layer diffusivity.« less

Selected data for wells and test holes used in structure-contour maps of the Inyan Kara Group, Minnekahta Limestone, Minnelusa Formation, Madison Limestone, and Deadwood Formation in the Black Hills area, South Dakota

USGS Publications Warehouse

Carter, J.M.

1999-01-01

This report presents selected data on wells and test holes that were used in the construction of structure-contour maps of selected formations that contain major aquifers in the Black Hills area of western South Dakota. Altitudes of the top of the Inyan Kara Group, Minnekahta Limestone, Minnelusa Formation, Madison Limestone, and Deadwood Formation are presented for the wells and test holes presented in this report.

Risk factors and reasons for treatment abandonment among children with lymphoma in Malawi.

PubMed

Stanley, Christopher C; van der Gronde, Toon; Westmoreland, Kate D; Salima, Ande; Amuquandoh, Amy; Itimu, Salama; Manda, Agness; Mtete, Idah; Butia, Mercy; Mpasa, Atupele; Wachepa, Stella; Fox, Paula; Wasswa, Peter; Kazembe, Peter; El-Mallawany, Nader K; Gopal, Satish

2018-03-01

Lymphoma is the commonest pediatric cancer in sub-Saharan Africa (SSA). Frequent treatment abandonment contributes to suboptimal outcomes. We examined risk factors and reasons for treatment abandonment for this population in Malawi. We conducted a mixed methods study among children < 18 years old with newly diagnosed lymphoma, prospectively enrolled during 2013-2016. All children received standardized diagnosis and treatment, and were followed for up to 2 years. Treatment abandonment was defined as failure to attend prescribed chemotherapy within 4 weeks, or post-treatment visit within 3 months. Child, guardian, and household characteristics associated with treatment abandonment were assessed. Semi-structured interviews were conducted with primary caregivers of children experiencing treatment abandonment. Of 121 children with newly diagnosed lymphoma, 72 (60%) had complete information regarding child, guardian, and household characteristics. Of these, 56 (78%) had Burkitt's and 16 (22%) Hodgkin's lymphoma. Forty-nine (68%) were male, median age was 10.6 years (interquartile range [IQR] 7.9-13.0), and 26 (36%) experienced treatment abandonment. Lack of guardian education and travel time ≥ 4 h to clinic were independently associated with treatment abandonment, with adjusted hazard ratio (aHR) 3.8 [95% confidence interval (CI) 1.5-8.9, p = 0.005] and aHR 2.9 (95% CI 1.2-6.9, p = 0.019), respectively. Commonest reasons for treatment abandonment endorsed by 15 guardians were community influence, suboptimal clinic environment, logistical challenges, transport costs, treatment toxicities, loss of hope, alternative healers, and beliefs about cure. These findings highlight families at risk for treatment abandonment, underlying reasons, and opportunities to improve retention in care for pediatric cancer patients in SSA.

Trepostome and cystoporate bryozoans from the Lexington Limestone and the Clays Ferry Formation (Middle and Upper Ordovician) of Kentucky

USGS Publications Warehouse

Karklins, O.L.

1984-01-01

The Lexington Limestone and the Clays Ferry Formation of Kentucky contain an abundant and diversified fossil invertebrate fauna. This report is concerned with the trepostome and cystoporate bryozoans that constitute a major part of that fauna. The Lexington Limestone, largely a biofragmental fossiliferous limestone, rests disconformably on the Tyrone Limestone (Middle Ordovician). The Clays Ferry Formation consists of approximately equal amounts of biofragmentallimestone and shale, and it overlies conformably, or intertongues with, the upper part of the Lexington Limestone. The Clays Ferry Formation is overlain by the Garrard Siltstone (Upper Ordovician) in central Kentucky and intertongues with the Kope Formation (Upper Ordovician) in northern Kentucky. The MiddleUpper Ordovician boundary falls within the upper part of the Lexington Limestone and laterally equivalent strata of the Clays Ferry Formation. The Lexington Limestone has been divided into 12 members, consisting of calcarenites, calcisiltites, calcilutites, nodular limestones, and shales in various amounts, that intertongue complexly. Because of the great abundance of bryozoans this study is generally limited to bryozoans recovered from, in ascending order, the Grier Limestone Member, the Perryville Limestone Member, the Brannon Member, the Tanglewood Limestone Member, and the Millersburg Member of the Lexington Limestone and from the Clays Ferry Formation and its Point Pleasant Tongue. The trepostome and cystoporate bryozoans discussed are referred to 36 species belonging to 22 genera. The trepostome component includes 29 species belonging to 16 genera: Amplexopora, Atactoporella, Balticopora, Batostoma, Cyphotrypa, Dekayia, Eridotrypa, Hetero-_ trypa, Homotrypa, Homotrypella, Mesotrypa, Parvohallopora, Peronopora, Prasopora, Stigmatella, and Tarphophragma, a new genus. Five of the trepostome species are new: Balticopora arcuatilis, Cyphotrypa switzeriensis, Dekayia epetrima, Eridotrypa sadievillensis

Wetland mitigation in abandoned gravel pits.

DOT National Transportation Integrated Search

2010-03-01

It is becoming increasingly difficult to provide on-site mitigation for wetland impacts due to road construction in : northeastern Minnesota counties that retain greater than 80 percent of their pre-settlement wetlands. Abandoned : gravel pits are on...

Water quality changes in acid mine drainage streams in Gangneung, Korea, 10 years after treatment with limestone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shim, Moo Joon; Choi, Byoung Young; Lee, Giehyeon

To determine the long-term effectiveness of the limestone treatment for acid mine drainage (AMD) in Gangneung, Korea, we investigated the elemental distribution in streams impacted by AMD and compared the results of previous studies before and approximately 10 years after the addition of limestone. Addition of limestone in 1999 leads to a pH increase in 2008, and with the exception of Ca, the elemental concentrations (e.g., Fe, Mn, Mg, Sr, Ni, Zn, S) in the streams decreased. The pH was 2.5–3 before the addition of limestone and remained stable at around 4.5–5 from 2008 to 2011, suggesting the reactivity ofmore » the added limestone was diminished and that an alternative approach is needed to increase the pH up to circumneutral range and maintain effective long-term treatment. To identify the processes causing the decrease in the elemental concentrations, we also examined the spatial (approximately 7 km) distribution over three different types of streams affected by the AMD. Lastly, the elemental distribution was mainly controlled by physicochemical processes including redox reactions, dilution on mixing, and co-precipitation/adsorption with Fe (hydr)oxides.« less

Water quality changes in acid mine drainage streams in Gangneung, Korea, 10 years after treatment with limestone

DOE PAGES

Shim, Moo Joon; Choi, Byoung Young; Lee, Giehyeon; ...

2015-09-28

To determine the long-term effectiveness of the limestone treatment for acid mine drainage (AMD) in Gangneung, Korea, we investigated the elemental distribution in streams impacted by AMD and compared the results of previous studies before and approximately 10 years after the addition of limestone. Addition of limestone in 1999 leads to a pH increase in 2008, and with the exception of Ca, the elemental concentrations (e.g., Fe, Mn, Mg, Sr, Ni, Zn, S) in the streams decreased. The pH was 2.5–3 before the addition of limestone and remained stable at around 4.5–5 from 2008 to 2011, suggesting the reactivity ofmore » the added limestone was diminished and that an alternative approach is needed to increase the pH up to circumneutral range and maintain effective long-term treatment. To identify the processes causing the decrease in the elemental concentrations, we also examined the spatial (approximately 7 km) distribution over three different types of streams affected by the AMD. Lastly, the elemental distribution was mainly controlled by physicochemical processes including redox reactions, dilution on mixing, and co-precipitation/adsorption with Fe (hydr)oxides.« less

Reduction of soil pollution by usingwaste of the limestone in the cement industry

NASA Astrophysics Data System (ADS)

Muñoz, M. Cecilia Soto; Robles Castillo, Marcelo; Blanco Fernandez, David; Diaz Gonzalez, Marcos; Naranjo Lamilla, Pedro; Moore Undurraga, Fernando; Pardo Fabregat, Francisco; Vidal, Manuel Miguel Jordan; Bech, Jaume; Roca, Nuria

2016-04-01

In the cement manufacturing process (wet) a residue is generated in the flotation process. This builds up causing contamination of soil, groundwater and agricultural land unusable type. In this study to reduce soil and water pollution 10% of the dose of cement was replaced by waste of origin limestone. Concretes were produced with 3 doses of cement and mechanical strengths of each type of concrete to 7, 28 and 90 days were determined. the results indicate that the characteristics of calcareous residue can replace up to 10% of the dose of cement without significant decreases in strength occurs. It is noted that use of the residue reduces the initial resistance, so that the dose of cement should not be less than 200 kg of cement per m3. The results allow recommends the use of limestone waste since it has been observed decrease in soil and water contamination without prejudice construction material Keywords: Soil contamination; Limestone residue; Adding concrete

150 years of land degradation and development: loss of habitats, natural resources due to quarrying and industrialization followed by land reclamation in the heart of Budapest city

NASA Astrophysics Data System (ADS)

Török, Ákos

2017-04-01

The urban development and land degradation is an accelerated process in the 21st century; however several examples are known when this happened in the past. A historic case study is discussed in this research when clump of three former small towns (named: Buda, Pest and Óbuda) became a million population city more than hundred years ago invoking significant land degradation, drastic and surprising changes in land use. Budapest which is now the capital of Hungary has seen rapid land use changes in the past 150 years especially from 1850'ies to early 20th century. The population of the city rapidly grown from the end of 19th century to early 20th century; i.e. it is tripled from 1880 to 1920 and reached nearly 1 million in 40 years. This population boom induced significant land degradation, changes in land use and loss of habitats. The paper presents examples how the land use has changed in the past 105 years with historic maps and interpreted cases suggesting different pathways leading to land degradation. The first one focuses on vineyards and grape cultivation and explains how these areas were first converted to limestone quarries to provide construction material to the city and then transformed to urban habitat in the early 20th century again. The cellars - former quarry galleries - than were used for housing (urban habitat) and later were used as storage facilities and mushroom cultivation sites. At present these subsurface openings cause high risk of land development (collapse) and limit the land use of the given area. The current paper also outlines the development of the city via the perspective of natural resources, since drinking water and industrial water need modified the land development and urbanization. Another example is also given how the brewery industry exploited natural resources and the surface water use was shifted to exploitation of karstic waters causing land degradation and drop of water table. Additional example demonstrates how the former

The role of men in abandonment of female genital mutilation: a systematic review.

PubMed

Varol, Nesrin; Turkmani, Sabera; Black, Kirsten; Hall, John; Dawson, Angela

2015-10-08

Men in their roles as fathers, husbands, community and religious leaders may play a pivotal part in the continuation of female genital mutilation (FGM). However, the research on their views of FGM and their potential role in its abandonment are not well described. We undertook a systematic review of all publications between 2004 and 2014 that explored men's attitudes, beliefs, and behaviours in regards to FGM, as well as their ideas about FGM prevention and abandonment. We included twenty peer-reviewed articles from 15 countries in the analysis. Analysis revealed ambiguity of men's wishes in regards to the continuation of FGM. Many men wished to abandon this practice because of the physical and psychosexual complications to both women and men. Social obligation and the silent culture between the sexes were posited as major obstacles for change. Support for abandonment was influenced by notions of social obligation, religion, education, ethnicity, urban living, migration, and understanding of the negative sequelae of FGM. The strongest influence was education. The level of education of men was one of the most important indicators for men's support for abandonment of FGM. Social obligation and the lack of dialogue between men and women were two key issues that men acknowledged as barriers to abandonment. Advocacy by men and collaboration between men and women's health and community programs may be important steps forward in the abandonment process.

Improving DMS 9210 requirements for limestone rock asphalt - final report.

DOT National Transportation Integrated Search

2015-03-01

Limestone Rock Asphalt (LRA) mixtures have been produced and placed for several decades using : specification requirements currently listed under DMS 9210. Several districts have had placement issues : and premature failures at the beginning of 2010....

Downflow limestone beds for treatment of net-acidic, oxic, iron-laden drainage from a flooded anthracite mine, Pennsylvania, USA: 2. Laboratory evaluation

USGS Publications Warehouse

Cravotta, C.A.; Ward, S.J.; Hammarstrom, J.M.

2008-01-01

Acidic mine drainage (AMD) containing elevated concentrations of dissolved iron and other metals can be neutralized to varying degrees by reactions with limestone in passive treatment systems. We evaluated the chemical and mineralogical characteristics and the effectiveness of calcitic and dolomitic limestone for the neutralization of net-acidic, oxic, iron-laden AMD from a flooded anthracite mine. The calcitic limestone, with CaCO3 and MgCO3 contents of 99.8 and <0.1 wt%, respectively, and the dolomitic limestone, with CaCO3 and MgCO3 contents of 60.3 and 40.2 wt%, were used to construct a downflow treatment system in 2003 at the Bell Mine, a large source of AMD and baseflow to the Schuylkill River in the Southern Anthracite Coalfield, in east-central Pennsylvania. In the winter of 2002-2003, laboratory neutralization-rate experiments evaluated the evolution of effluent quality during 2 weeks of continuous contact between AMD from the Bell Mine and the crushed calcitic or dolomitic limestone in closed, collapsible containers (cubitainers). The cubitainer tests showed that: (1) net-alkaline effluent could be achieved with detention times greater than 3 h, (2) effluent alkalinities and associated dissolution rates were equivalent for uncoated and Fe(OH)3-coated calcitic limestone, and (3) effluent alkalinities and associated dissolution rates for dolomitic limestone were about half those for calcitic limestone. The dissolution rate data for the cubitainer tests were used with data on the volume of effuent and surface area of limestone in the treatment system at the Bell Mine to evaluate the water-quality data for the first 1.5 years of operation of the treatment system. These rate models supported the interpretation of field results and indicated that treatment benefits were derived mainly from the dissolution of calcitic limestone, despite a greater quantity of dolomitic limestone within the treatment system. The dissolution-rate models were extrapolated on a

Aging and Curing Temperature Effects on Compressive Strength of Mortar Containing Lime Stone Quarry Dust and Industrial Granite Sludge.

PubMed

Amin, Muhammad Nasir; Khan, Kaffayatullah; Saleem, Muhammad Umair; Khurram, Nauman; Niazi, Muhammad Umar Khan

2017-06-11

In this study, the researchers investigated the potential use of locally available waste materials from the lime stone quarry and the granite industry as a partial replacement of cement. Quarry sites and granite industry in the eastern province of Saudi Arabia produces tons of powder wastes in the form of quarry dust (QD) and granite sludge (GS), respectively, causing serious environmental problems along with frequent dust storms in the area. According to ASTM C109, identical 50-mm3 specimens were cast throughout this study to evaluate the compressive strength development of mortars (7, 28 and 91 days) containing these waste materials. Experimental variables included different percentage replacement of cement with waste materials (GS, QD), fineness of GS, various curing temperatures (20, 40 and 60 °C as local normal and hot environmental temperatures) and curing moisture (continuously moist and partially moist followed by air curing). Finally, the results of mortar containing waste materials were compared to corresponding results of control mortar (CM) and mortar containing fly ash (FA). The test results indicated that under normal curing (20 °C, moist cured), the compressive strength of mortar containing the different percentage of waste materials (QD, GS, FA and their combinations) remained lower than that of CM at all ages. However, the compressive strength of mortar containing waste materials slightly increased with increased fineness of GS and significantly increased under high curing temperatures. It was recommended that more fineness of GS be achieved to use its high percentage replacement with cement (30% or more) incorporating local environmental conditions.

Aging and Curing Temperature Effects on Compressive Strength of Mortar Containing Lime Stone Quarry Dust and Industrial Granite Sludge

PubMed Central

Amin, Muhammad Nasir; Khan, Kaffayatullah; Saleem, Muhammad Umair; Khurram, Nauman; Niazi, Muhammad Umar Khan

2017-01-01

In this study, the researchers investigated the potential use of locally available waste materials from the lime stone quarry and the granite industry as a partial replacement of cement. Quarry sites and granite industry in the eastern province of Saudi Arabia produces tons of powder wastes in the form of quarry dust (QD) and granite sludge (GS), respectively, causing serious environmental problems along with frequent dust storms in the area. According to ASTM C109, identical 50-mm3 specimens were cast throughout this study to evaluate the compressive strength development of mortars (7, 28 and 91 days) containing these waste materials. Experimental variables included different percentage replacement of cement with waste materials (GS, QD), fineness of GS, various curing temperatures (20, 40 and 60 °C as local normal and hot environmental temperatures) and curing moisture (continuously moist and partially moist followed by air curing). Finally, the results of mortar containing waste materials were compared to corresponding results of control mortar (CM) and mortar containing fly ash (FA). The test results indicated that under normal curing (20 °C, moist cured), the compressive strength of mortar containing the different percentage of waste materials (QD, GS, FA and their combinations) remained lower than that of CM at all ages. However, the compressive strength of mortar containing waste materials slightly increased with increased fineness of GS and significantly increased under high curing temperatures. It was recommended that more fineness of GS be achieved to use its high percentage replacement with cement (30% or more) incorporating local environmental conditions. PMID:28772999

19 CFR 127.41 - Government title to unclaimed and abandoned merchandise.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SECURITY; DEPARTMENT OF THE TREASURY GENERAL ORDER, UNCLAIMED, AND ABANDONED MERCHANDISE Title to Unclaimed... part, at which time merchandise having thus remained in Customs custody is considered as unclaimed and abandoned, the port director, with the concurrence of the Assistant Commissioner, Office of Field Operations...

Fluorspar

USGS Publications Warehouse

Miller, M.M.

2011-01-01

World fluorspar demand showed some signs of recovery in 2010 but was still depressed compared with 2008. In 2010, nearly all fluorspar (CaF[sub2]) consumption in the United States was from imports. Hastie Mining and Trucking Co. produced some fluorspar as a byproduct from its limestone quarry operations in Illinois. In addition, a small amount of usable synthetic fluorspar was produced from industrial waste streams.

76 FR 78974 - Wisconsin Central Ltd.-Abandonment Exemption-in Fond Du Lac County, WI

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-20

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. AB 303 (Sub-No. 38X)] Wisconsin Central Ltd.--Abandonment Exemption--in Fond Du Lac County, WI Wisconsin Central Ltd. (WCL) \\1\\ filed a verified notice of exemption under 49 CFR pt. 1152 subpart F--Exempt Abandonments to abandon...

Diagenetic patterns and pore space distribution along a platform to outer-shelf transect (Urgonian limestone, Barremian-Aptian, SE France)

NASA Astrophysics Data System (ADS)

Léonide, Philippe; Fournier, François; Reijmer, John J. G.; Vonhof, Hubert; Borgomano, Jean; Dijk, Jurrien; Rosenthal, Maelle; van Goethem, Manon; Cochard, Jean; Meulenaars, Karlien

2014-06-01

The Urgonian limestones of Late Barremian/Early Aptian from Provence (SE, France) are characterized by the occurrence of microporous limestones at regional scale alternating with tight carbonates. This study, based on petrographical (sediment texture, facies) and diagenetical analyses (cement stratigraphy, porosity and isotope geochemistry) of more than 800 limestone samples provides insight into the parameters controlling the genesis, preservation or occlusion of microporosity along an inner platform to outer shelf transect. The tight and microporous Urgonian limestones from Provence can be grouped into 5 rock-types based on textures, associated depositional environments, porosity and pore-type, being: (1) tight inner-platform: TIP; (2) porous inner platform: PIP; (3) tight outer platform: TOP; (4) porous outer platform: POP and (5) tight outer shelf: TOS. In tight (TIP, TOP and TOS types) limestones intergranular and intragranular pore spaces were entirely occluded by early marine and/or early meteoric cementation, whereas in microporous (PIP, POP) limestones a significant fraction of the intergranular macroporosity was preserved during early and shallow burial diagenesis. Micrite neomorphism (hybrid Ostwald ripening process) occurred during meteoric shallow burial diagenesis in PIP and POP limestones during the regional Durancian Uplift event (Albian-Lower Cenomanian). This process resulted in microporosity enhancement and preservation. Circulation of meteoric fluids during exhumation produces intercrystalline microporosity enhancement and moldic porosity development. The present study documents the important role that both early diagenetic and depositional cycles and long-term tectonic processes have on pore space evolution and distribution in Mesozoic platform carbonates.

18 CFR 157.18 - Applications to abandon facilities or service; exhibits.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Applications to abandon facilities or service; exhibits. 157.18 Section 157.18 Conservation of Power and Water Resources FEDERAL..., Concerning Any Operation, Sales, Service, Construction, Extension, Acquisition or Abandonment § 157.18...

18 CFR 157.18 - Applications to abandon facilities or service; exhibits.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Applications to abandon facilities or service; exhibits. 157.18 Section 157.18 Conservation of Power and Water Resources FEDERAL..., Concerning Any Operation, Sales, Service, Construction, Extension, Acquisition or Abandonment § 157.18...

18 CFR 157.18 - Applications to abandon facilities or service; exhibits.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 18 Conservation of Power and Water Resources 1 2014-04-01 2014-04-01 false Applications to abandon facilities or service; exhibits. 157.18 Section 157.18 Conservation of Power and Water Resources FEDERAL..., Concerning Any Operation, Sales, Service, Construction, Extension, Acquisition or Abandonment § 157.18...

18 CFR 157.18 - Applications to abandon facilities or service; exhibits.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Applications to abandon facilities or service; exhibits. 157.18 Section 157.18 Conservation of Power and Water Resources FEDERAL..., Concerning Any Operation, Sales, Service, Construction, Extension, Acquisition or Abandonment § 157.18...

18 CFR 157.18 - Applications to abandon facilities or service; exhibits.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Applications to abandon facilities or service; exhibits. 157.18 Section 157.18 Conservation of Power and Water Resources FEDERAL..., Concerning Any Operation, Sales, Service, Construction, Extension, Acquisition or Abandonment § 157.18...

Kinetics of autotrophic denitrification process and the impact of sulphur/limestone ratio on the process performance.

PubMed

Kilic, Arzu; Sahinkaya, Erkan; Cinar, Ozer

2014-01-01

Kinetics of sulphur-limestone autotrophic denitrification process in batch assays and the impact of sulphur/limestone ratio on the process performance in long-term operated packed-bed bioreactors were evaluated. The specific nitrate and nitrite reduction rates increased almost linearly with the increasing initial nitrate and nitrite concentrations, respectively. The process performance was evaluated in three parallel packed-bed bioreactors filled with different sulphur/limestone ratios (1:1, 2:1 and 3:1, v/v). Performances of the bioreactors were studied under varying nitrate loadings (0.05 - 0.80 gNO(-)(3) - NL⁻¹ d⁻¹) and hydraulic retention times (3-12 h). The maximum nitrate reduction rate of 0.66 g L⁻¹ d⁻¹ was observed at the loading rate of 0.80 g NO(-)(3) - N L⁻¹ d⁻¹ in the reactor with sulphur/limestone ratio of 3:1. Throughout the study, nitrite concentrations remained quite low (i.e. below 0.5 mg L⁻¹ NO(-)(2) -N. The reactor performance increased in the order of sulphur/limestone ratio of 3:1, 2:1 and 1:1. Denaturing gradient gel electrophoresis analysis of 16S rRNA genes showed quite stable communities in the reactors with the presence of Methylo virgulaligni, Sulfurimonas autotrophica, Sulfurovum lithotrophicum, Thiobacillus aquaesulis and Sulfurimonas autotrophica related species.

Assessment of postcrumble addition of limestone and calcium-specific appetite in broilers during the starter phase1

PubMed Central

Li, W.; Angel, R.; Kim, S.-W.; Jiménez-Moreno, E.; Proszkowiec-Weglarz, M.; Iglesias, B. F.; Wilkinson, S. J.; Cowieson, A. J.

2014-01-01

A study was done to determine whether broilers can regulate Ca intake when limestone is provided separately or mixed with a crumbled feed of variable Ca and P content, and the influence of this on performance and apparent ileal digestibility (AID) of Ca and P (AIDP). Twelve crumbled diets were fed from 10 to 20 d of age (8 replicates, 8 broilers/replicate). Diets A to D contained 0.28% nonphytate P (nPP) and 0.27, 0.51, 0.77, and 1.02% Ca, respectively. Diets E to H contained 0.48% nPP and 0.41, 0.51, 0.77, and 1.02% Ca, respectively. A large particle size limestone was mixed manually to the crumbled diet on a daily basis to achieve 1.02% total Ca in diets A to H. Diets I to L had the same Ca and nPP as diets A to D, but limestone was provided in a separate feeder to assess spatial importance of limestone supply. Limestone consumption, provided in a separate feeder, decreased as Ca concentration increased in the crumble diet (P < 0.05). Calcium intake increased as Ca concentration in crumbled diets increased (P < 0.05). Increased tibia ash and decreased AIDP were observed as Ca intake increased (P < 0.05). When limestone was added to diets containing 0.28% nPP postcrumble, Ca intake (6.38 g/bird), tibia ash (717 mg/bone), and AIDP (39.78%) were not affected by crumbled diet Ca concentration or consumed Ca. Broilers fed diets containing 0.48% nPP and limestone mixed with the crumble, Ca intake changed (5.96, 6.93, 6.59, and 6.04 g/bird for crumble diet with 0.41, 0.51, 0.77, and 1.02% Ca, respectively). Increasing Ca concentration in the crumble from 0.41 to 1.02% resulted in greater tibia ash (875 mg/bone) but lower AIDP (P < 0.05), although Ca intake was similar. In conclusion, when large particle size limestone was provided ad libitum, the ability of broilers to select for Ca was not sufficient to meet their requirement when crumble Ca was less than 0.77%. The AIDP was highest in birds fed the 0.27% Ca concentration diet. PMID:25085931

Biogenic magnetite as a primary remanence carrier in limestone deposits

NASA Astrophysics Data System (ADS)

Chang, Shih-Bin R.; Kirschvink, Joseph L.; Stolz, John F.

1987-06-01

Studies on the microbial communities and magnetic phases of samples collected from carbonate oozes at Sugarloaf Key, FL, U.S.A. and calcareous laminated sediments from Laguna Figueroa, Baja California, Mexico have revealed the existence of magnetotactic bacteria and ultrafine-grained single domain magnetite in both environments. Magnetotactic bacteria were identified by light and electron microscopy. The single domain magnetite was detected by coercivity spectra analysis with a SQUID magnetometer and examined under the transmission electron microscope. The similarity, in terms of size and shape, between the single domain magnetite found in these sediments and the magnetite observed in the bacterial magnetosome from enriched cultures indicates the ultrafine-grained magnetite in these two marine environments was biologically formed. These results, combined with the common occurrences of ultrafine-grained magnetite in limestone deposits detected rock magnetically, suggest biogenic magnetite may be present and contribute to the magnetic remanence in these rocks. Several Cambrian limestone samples, separately collected from Siberia, China, and Kazakhstan, were examined for the presence of bacterial magnetite. Samples from the Lower Cambrian Sinskian Formation at Siberia Platform were found to contain both a large amount of apparently bacterial magnetite particles and a very stable primary magnetic component. Post-Cambrian diagenesis does not seem to affect the microgranulometry of these apparently bacterial magnetite crystals or the magnetic remanence carried by them. Assessing the potential role of biogenic magnetite as a primary remanence carrier in other Phanerozoic limestone deposits ought to be further pursued.

Mechanical and chemical compaction in fine-grained shallow-water limestones.

USGS Publications Warehouse

Shinn, E.A.; Robbin, D.M.

1983-01-01

Significant mechanical compaction resulted from pressures simulating less than 305 m of burial. Increasing loads to an equivalent of more than 3400 m did not significantly increase compaction or reduce sediment core length. Chemical compaction (pressure dissolution) was detected only in sediment cores compacted to pressures greater than 3400 m of burial. These short-term experiments suggest that chemical compaction would begin at much shallower depths given geologic time. Compaction experiments that caused chemical compaction lend support to the well-established hypothesis; that cement required to produce a low-porosity/low-permeability fine-grained limestone is derived internally. Dissolution, ion diffusion, and reprecipitation are considered the most likely processes for creating significant thicknesses of dense limestone in the geologic record. Continuation of chemical compaction after significant porosity reduction necessitates expulsion of connate fluids, possibly including hydrocarbons. -from Authors

Investigation on factors that contribute to the abandonment of building in construction industry in Malaysia

NASA Astrophysics Data System (ADS)

Farhayu Ariffin, Nur; Jaafar, Mohd Faizal Md; Idris Ali, Mohamad; Irwan Ramli, Noram; Muthusamy, Khairunisa; Shukor Lim, Nor Hasanah Abdul

2018-03-01

In Malaysia, the construction sector is one of the important sectors that contribute to economic growth and employments. However, a major concern facing the construction industry is the growing rate of delays in project delivery. In the worse cases, the projects were abandoned due to some reasons when the contract period ended. Abandoned building defines as construction work that has been continuously stalled for 6 months or more, during the project completion period or beyond the scheduled date of completion. When the projects become abandoned, it gives an adverse effect on many parties such as the developer, contractor, consultant and also client. According to previous researchers, the abandonment of building causes a serious problem and need some mitigation plan to avoid this problem from occurring. This study will investigate the fundamental factors that contribute to the abandonment of building and projects in Malaysia based on the current data of the abandoned building in most states in Malaysia. The data was collected from the respondents who is in the construction industry and had experience working with abandoned housing project. Form the respondents perspective, it shows that the main factor contribute to the building abandonment is due to the financial problem facing by the developer company.

Testing the temporal nature of social disorder through abandoned buildings and interstitial spaces.

PubMed

Wallace, Danielle; Schalliol, David

2015-11-01

With the recent housing crisis, studying abandoned buildings has once again become important. However, it has been some time since abandoned buildings were the subject of direct study, leaving scholars with scant knowledge about the characteristics of abandoned buildings, how they change, and their relationship to neighborhood processes. To fill this gap, we employed longitudinal photographic and SSO evaluations of 36 abandoned buildings and their immediate surroundings in Chicago for one year (n=587). Results demonstrate the presence and severity of social disorder cues vary across time points and the time of day of observation. There is a relationship between abandoned buildings and social disorder, though the relationship is not a trend. Also, social disorder is diminished around extremely decayed buildings. Lastly, we find that our results are driven by the measurement of places ignored by most SSO studies, including alleys and the rear side of buildings. Copyright © 2015 Elsevier Inc. All rights reserved.

Agricultural land abandonment in Mediterranean environment provides ecosystem services via soil carbon sequestration.

PubMed

Novara, Agata; Gristina, Luciano; Sala, Giovanna; Galati, Antonino; Crescimanno, Maria; Cerdà, Artemi; Badalamenti, Emilio; La Mantia, Tommaso

2017-01-15

Abandonment of agricultural land leads to several consequences for ecosystem functions. Agricultural abandonment may be a significant and low cost strategy for carbon sequestration and mitigation of anthropogenic CO 2 emissions due to the vegetation recovery and increase in soil organic matter. The aim of this study was to: (i) estimate the influence of different Soil Regions (areas characterized by a typical climate and parent material association) and Bioclimates (zones with homogeneous climatic regions and thermotype indices) on soil organic carbon (SOC) dynamics after agricultural land abandonment; and (ii) to analyse the efficiency of the agri-environment policy (agri-environment measures) suggested by the European Commission in relation to potential SOC stock ability in the Sicilian Region (Italy). In order to quantify the effects of agricultural abandonment on SOC, a dataset with original data that was sampled in Sicily and existing data from the literature were analysed according to the IPCC (Intergovernmental Panel on Climate Change) methodology. Results showed that abandonment of cropland soils increased SOC stock by 9.03MgCha -1 on average, ranging from 5.4MgCha -1 to 26.7MgCha -1 in relation to the Soil Region and Bioclimate. The estimation of SOC change after agricultural use permitted calculation of the payments for ecosystem service (PES) of C sequestration after agricultural land abandonment in relation to environmental benefits, increasing in this way the efficiency of PES. Considering the 14,337ha of abandoned lands in Sicily, the CO 2 emission as a whole was reduced by 887,745Mg CO 2 . Therefore, it could be concluded that abandoned agricultural fields represents a valid opportunity to mitigate agriculture sector emissions in Sicily. Copyright © 2016 Elsevier B.V. All rights reserved.

Occupational exposure due to naturally occurring radionuclide material in granite quarry industry.

PubMed

Ademola, J A

2012-02-01

The potential occupational exposure in granite quarry industry due to the presence of naturally occurring radioactive material (NORM) has been investigated. The activity concentrations of (40)K, (226)Ra and (232)Th were determined using gamma-ray spectroscopy method. The annual effective dose of workers through different exposure pathways was determined by model calculations. The total annual effective dose varied from 21.48 to 33.69 μSv y(-1). Inhalation dose contributes the highest to the total effective dose. The results obtained were much lower than the intervention exemption levels (1.0 mSv y(-1)) given in the International Commission on Radiological Protection Publication 82.

Limestone and Zeolite as Alternative Media in Horizontal Subsurface Flow Constructed Wetlands: Laboratory-Scale Studies

NASA Astrophysics Data System (ADS)

Lizama, K.; Jaque, I.; Ayala, J.

2016-12-01

Arsenic is well known for its chronic toxicity. Millions of people around the world are currently at risk, drinking water with As concentrations above 10 ppb, the WHO drinking water guideline. Although different treatment options exist, they are often limited by elevated costs and maintenance requirements. Constructed wetlands are a natural water treatment system, capable to remove metals and metalloids -including As- via different physical, chemical and biological processes. The use of alternative supporting media to enhance As removal in subsurface flow wetlands has been recommended, but not sufficiently studied. Limestone and zeolite have been identified as effective supporting media in subsurface flow wetlands aiming As removal. However, there are still key aspects to be addressed, such as the implications of using these media, the speciation in the solid phase, the role of vegetation, etc. This study investigated the performance of limestone and zeolite in three types of experiments: batch, column and as main supporting media in a bench scale horizontal subsurface flow wetland system. Synthetic water resembling a contaminated river in Chile (As concentration=3 mg/L, Fe concentration= 100 mg/L, pH=2) was used in all experiments. In the batch experiments, the As concentration, the mass of media and the contact time were varied. The column system consisted of three limestone columns and three zeolite columns, operated under a hydraulic loading of 20 mm/d. The wetland system consisted of twelve PVC cells: six filled with zeolite and six with limestone. Phragmites australis were planted in three cells of each media type, as control cells. From the batch experiments, maximum As sorption capacities as indicated by Langmuir model were 1.3 mg/g for limestone and 0.17 mg/g for zeolite, at 18 h contact time and 6.3 g/L medium concentration. EDS and XPS analyses revealed that As and Fe were retained in zeolite at the end of the batch experiments. Zeolite and limestone

Freshwater biodissolution rates of limestone in the temperate climate of the Dinaric karst in Slovenia

NASA Astrophysics Data System (ADS)

Mulec, J.; Prelovšek, M.

2015-01-01

Dissolution rates in two freshwater karst systems were determined by using tablets of dense micrite-biopelmicrite Cretaceous limestone. Submerged limestone tablets in riverbeds were subjected to a natural gradient from complete darkness to direct sunlight. Higher light rates significantly (p < 0.05) increased the epilithic biomass of phototrophs and the overall dissolution rates, which were highest at the Unica spring (- 49.2 μm a- 1), but the exact portion of light-dependent dissolution remains elusive. In the karst river Unica, with its big fluctuations in environmental parameters (e.g., discharge), light rates can be used in estimating the dissolution rates enhanced by phototrophs. Natural biofilms in aquatic systems have important implications for landform evolution, and the impact on limestone dissolution rates is comparable with rates of debris falling from steep slopes.

Passive bioremediation technology incorporating lignocellulosic spent mushroom compost and limestone for metal- and sulfate-rich acid mine drainage.

PubMed

Muhammad, Siti Nurjaliah; Kusin, Faradiella Mohd; Md Zahar, Mohd Syakirin; Mohamat Yusuff, Ferdaus; Halimoon, Normala

2017-08-01

Passive bioremediation of metal- and sulfate-containing acid mine drainage (AMD) has been investigated in a batch study. Multiple substrates were used in the AMD remediation using spent mushroom compost (SMC), limestone, activated sludge (AS), and woodchips (WC) under anoxic conditions suitable for bacterial sulfate reduction (BSR). Limestones used were of crushed limestone (CLS) and uncrushed limestone, provided at two different ratios in mixed substrates treatment and varied by the proportion of SMC and limestone. The SMC greatly assisted the removals of sulfate and metals and also acted as an essential carbon source for BSR. The mixed substrate composed of 40% CLS, 30% SMC, 20% AS, and 10% WC was found to be effective for metal removal. Mn, Cu, Pb, and Zn were greatly removed (89-100%) in the mixed substrates treatment, while Fe was only removed at 65%. Mn was found to be removed at a greatly higher rate than Fe, suggesting important Mn adsorption onto organic materials, that is, greater sorption affinity to the SMC. Complementary with multiple treatment media was the main mechanism assisting the AMD treatment through microbial metal reduction reactions.

Prevalence and predictors of abandonment of therapy among children with cancer in El Salvador.

PubMed

Bonilla, Miguel; Rossell, Nuria; Salaverria, Carmen; Gupta, Sumit; Barr, Ronald; Sala, Alessandra; Metzger, Monika L; Sung, Lillian

2009-11-01

Abandonment of therapy is one of the most common causes of treatment failure among children with cancer in low-income countries. Our objectives were to describe the prevalence and predictors of abandonment among such children with cancer in El Salvador. We analyzed data on patients younger than 16 years, diagnosed with any malignancy between January 2001 and December 2003 at the Benjamin Bloom National Children's Hospital, San Salvador. Among 612 patients, 353 were male (58%); the median age at diagnosis was 5.1 years; 59% of patients were diagnosed with leukemia/lymphoma, 28% with solid tumors and 13% with brain tumors. The prevalence of abandonment was 13%. Median time to abandonment was 2.0 (range 0-36) months. In univariate analyses, paternal illiteracy [odds ratio (OR) 3.8, 95% confidence interval (CI) 2.0-7.2; p = 0.001]; maternal illiteracy (OR = 5.1, 95% CI 2.5-10; p < 0.0001); increasing number of household members (OR = 1.2, 95% CI 1.1-1.3; p = 0.004); and low monthly household income (OR per $100 = 0.59, 95% CI 0.45-0.75; p < 0.0001) all significantly increased the risk of abandonment, whereas travel time to hospital did not. In multiple regression analyses, low monthly income and increased number of people in the household were independently predictive of abandonment. In conclusion, in El Salvador, despite the provision of free treatment, socioeconomic variables significantly predict increased risk of abandonment of therapy. Understanding the pathways through which socioeconomic status affects abandonment may allow the design of effective interventions. (c) 2009 UICC.

Spatial Risk Analysis of Hydraulic Fracturing near Abandoned and Converted Oil and Gas Wells.

PubMed

Brownlow, Joshua W; Yelderman, Joe C; James, Scott C

2017-03-01

Interaction between hydraulically generated fractures and existing wells (frac hits) could represent a potential risk to groundwater. In particular, frac hits on abandoned oil and gas wells could lead to upward leakage into overlying aquifers, provided migration pathways are present along the abandoned well. However, potential risk to groundwater is relatively unknown because few studies have investigated the probability of frac hits on abandoned wells. In this study, actual numbers of frac hits were not determined. Rather, the probability for abandoned wells to intersect hypothetical stimulated reservoir sizes of horizontal wells was investigated. Well data were compiled and analyzed for location and reservoir information, and sensitivity analyses were conducted by varying assumed sizes of stimulated reservoirs. This study used public and industry data for the Eagle Ford Shale play in south Texas, with specific attention paid to abandoned oil and gas wells converted into water wells (converted wells). In counties with Eagle Ford Shale activity, well-data analysis identified 55,720 abandoned wells with a median age of 1983, and 2400 converted wells with a median age of 1954. The most aggressive scenario resulted in 823 abandoned wells and 184 converted wells intersecting the largest assumed stimulated reservoir size. Analysis showed abandoned wells have the potential to be intersected by multiple stimulated reservoirs, and risks for intersection would increase if currently permitted horizontal wells in the Eagle Ford Shale are actually completed. Results underscore the need to evaluate historical oil and gas activities in areas with modern unconventional oil and gas activities. © 2016, National Ground Water Association.

Influence of Hydraulic Fracturing on Overlying Aquifers in the Presence of Leaky Abandoned Wells.

PubMed

Brownlow, Joshua W; James, Scott C; Yelderman, Joe C

2016-11-01

The association between hydrocarbon-rich reservoirs and organic-rich source rocks means unconventional oil and gas plays usually occur in mature sedimentary basins-where large-scale conventional development has already taken place. Abandoned wells in proximity to hydraulic fracturing could be affected by increased fluid pressures and corresponding newly generated fractures that directly connect (frac hit) to an abandoned well or to existing fractures intersecting an abandoned well. If contaminants migrate to a pathway hydraulically connected to an abandoned well, upward leakage may occur. Potential effects of hydraulic fracturing on upward flow through a particular type of leaky abandoned well-abandoned oil and gas wells converted into water wells were investigated using numerical modeling. Several factors that affect flow to leaky wells were considered including proximity of a leaky well to hydraulic fracturing, flowback, production, and leaky well abandonment methods. The numerical model used historical records and available industry data for the Eagle Ford Shale play in south Texas. Numerical simulations indicate that upward contaminant migration could occur through leaky converted wells if certain spatial and hydraulic conditions exist. Upward flow through leaky converted wells increased with proximity to hydraulic fracturing, but decreased when flowback and production occurred. Volumetric flow rates ranged between 0 and 0.086 m 3 /d for hydraulic-fracturing scenarios. Potential groundwater impacts should be paired with plausible transport mechanisms, and upward flow through leaky abandoned wells could be unrelated to hydraulic fracturing. The results also underscore the need to evaluate historical activities. © 2016, National Ground Water Association.

Floodplain/wetlands assessment for the interceptor trench field study near the Weldon Spring Quarry, Weldon Spring Site, Missouri

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Lonkhuyzen, R.A.

1999-12-15

The US Department of Energy proposes to construct a groundwater interceptor trench near the Weldon Spring Quarry at the Weldon Spring Site in Missouri. The trench would be located near two palustrine wetland areas. Impacts to wetland hydrology and biotic communities are expected to be negligible. No long-term adverse impacts to floodplains are expected.

Association of prescription abandonment with cost share for high-cost specialty pharmacy medications.

PubMed

Gleason, Patrick P; Starner, Catherine I; Gunderson, Brent W; Schafer, Jeremy A; Sarran, H Scott

2009-10-01

In 2008, specialty medications accounted for 15.1% of total pharmacy benefit medication spending, and per member expenditures have increased by 11.1% annually from 2004 to 2008 within a commercially insured population of 8 million members. Insurers face increasing pressure to control specialty medication expenditures and to rely on increasing member cost share through creation of a fourth copayment tier within the incentive-based formulary pharmacy benefit system. Data are needed on the influence that member out-of-pocket (OOP) expense may have on prescription abandonment (defined as the patient never actually taking possession of the medication despite evidence of a written prescription generated by a prescriber). To explore the relationship between prescription abandonment and OOP expense among individuals newly initiating high-cost medication therapy with a tumor necrosis factor (TNF) blocker or multiple sclerosis (MS) biologic agent. This observational cross-sectional study queried a midwestern and southern U.S. database of 13,172,480 commercially insured individuals to find members with a pharmacy benefit-adjudicated claim for a TNF blocker or MS specialty medication during the period from July 2006 through June 2008. Prescription abandonment was assessed among continuously enrolled members newly initiating TNF blocker or MS therapy. Prescription abandonment was defined as reversal of the adjudicated claim with no evidence of a subsequent additional adjudicated paid claim in the ensuing 90 days. Separate analyses for MS and TNF blocker therapy were performed to assess the association between member OOP expense and abandonment rate using the Cochran-Armitage test for trend and multivariate logistic regression. Members were placed into 1 of the 7 following OOP expense groups per claim: $0-$100, $101-$150, $151-$200, $201-$250, $251-$350, $351-$500, or more than $500. The association of MS or TNF blocker abandonment rate with OOP expense was tested with logistic

Effects of organic amendments and mulches on soil microbial communities in quarry restoration under semiarid climate

NASA Astrophysics Data System (ADS)

Luna Ramos, Lourdes; Pastorelli, Roberta; Miralles Mellado, Isabel; Fabiani, Arturo; Bastida López, Felipe; Hernández Fernández, María Teresa; García Izquierdo, Carlos; Solé Benet, Albert

2015-04-01

Mining activities generate loss of the quality of the environment and landscape specially in arid and semiarid Mediterranean regions. A precondition for ecosystem reclamation in such highly disturbed mining areas is the development of functional soils with appropriate levels of organic matter. In an experimental soil restoration in limestone quarries from Sierra de Gádor (Almería), SE Spain, 9 plots 15 x 5 m were prepared to test organic amendments (compost from solid urban residues-DOW-, sludge from urban water treatment-SS-, control-NA-) and different mulches (fine gravel-GM-, wood chips-WM-, control-NM-) with the aim to improve soil/substrate properties and to reduce evaporation and erosion. In each experimental plot, 75 native plants (Macrochloa tenacissima, Anthyllis terniflora and Anthyllis cytisoides) were planted. After 5 years from the start of the experiment, we evaluated how microbial community composition responded to the organic amendments and mulches. Microbial community composition of both bacteria and fungi was determined by phospholipid fatty acid (PLFA) and polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) fingerprinting. The results of the two-way ANOVA showed that PLFAs were significantly affected by organic amendments but not by the mulches or interaction of both factors. Experimental plots with DOW showed significantly higher level of fungal PLFAs than those with SS and NA, even higher than the reference undisturbed soil. However, any plot with organic amendments did not reach the content of bacterial PLFAs of the reference soils. The bacterial diversity (evaluated by diversity indices calculated from DGGE profiles) was greater in soil samples taken under NA and GM. Comparing these indices in fungal DGGE, we found greater values for soil samples taken under DOW and without mulches. Results from UPGMA analysis showed significant differences in the structure of soil bacterial communities from the different treatments

Rapid method to determine actinides and 89/90Sr in limestone and marble samples

DOE PAGES

Maxwell, Sherrod L.; Culligan, Brian; Hutchison, Jay B.; ...

2016-04-12

A new method for the determination of actinides and radiostrontium in limestone and marble samples has been developed that utilizes a rapid sodium hydroxide fusion to digest the sample. Following rapid pre-concentration steps to remove sample matrix interferences, the actinides and 89/90Sr are separated using extraction chromatographic resins and measured radiometrically. The advantages of sodium hydroxide fusion versus other fusion techniques will be discussed. Lastly, this approach has a sample preparation time for limestone and marble samples of <4 hours.

Spatiotemporal variation of radon and carbon dioxide concentrations in an underground quarry: coupled processes of natural ventilation, barometric pumping and internal mixing.

PubMed

Perrier, Frédéric; Richon, Patrick

2010-04-01

Radon-222 and carbon dioxide concentrations have been measured during several years at several points in the atmosphere of an underground limestone quarry located at a depth of 18 m in Vincennes, near Paris, France. Both concentrations showed a seasonal cycle. Radon concentration varied from 1200 to 2000 Bq m(-3) in summer to about 800-1400 Bq m(-3) in winter, indicating winter ventilation rates varying from 0.6 to 2.5 x 10(-6) s(-1). Carbon dioxide concentration varied from 0.9 to 1.0% in summer, to about 0.1-0.3% in winter. Radon concentration can be corrected for natural ventilation using temperature measurements. The obtained model also accounts for the measured seasonal variation of carbon dioxide. After correction, radon concentrations still exhibit significant temporal variation, mostly associated with the variation of atmospheric pressure, with coupling coefficients varying from -7 to -26 Bq m(-3) hPa(-1). This variation can be accounted for using a barometric pumping model, coupled with natural ventilation in winter, and including internal mixing as well. After correction, radon concentrations exhibit residual temporal variation, poorly correlated between different points, with standard deviations varying from 3 to 6%. This study shows that temporal variation of radon concentrations in underground cavities can be understood to a satisfactory level of detail using non-linear and time-dependent modelling. It is important to understand the temporal variation of radon concentrations and the limitations in their modelling to monitor the properties of natural or artificial underground settings, and to be able to assess the existence of new processes, for example associated with the preparatory phases of volcanic eruptions or earthquakes. Copyright 2009 Elsevier Ltd. All rights reserved.

Micromechanics of cataclastic pore collapse in limestone

NASA Astrophysics Data System (ADS)

Zhu, Wei; Baud, Patrick; Wong, Teng-Fong

2010-04-01

The analysis of compactant failure in carbonate formations hinges upon a fundamental understanding of the mechanics of inelastic compaction. Microstructural observations indicate that pore collapse in a limestone initiates at the larger pores, and microcracking dominates the deformation in the periphery of a collapsed pore. To capture these micromechanical processes, we developed a model treating the limestone as a dual porosity medium, with the total porosity partitioned between macroporosity and microporosity. The representative volume element is made up of a large pore which is surrounded by an effective medium containing the microporosity. Cataclastic yielding of this effective medium obeys the Mohr-Coulomb or Drucker-Prager criterion, with failure parameters dependent on porosity and pore size. An analytic approximation was derived for the unconfined compressive strength associated with failure due to the propagation and coalescence of pore-emanated cracks. For hydrostatic loading, identical theoretical results for the pore collapse pressure were obtained using the Mohr-Coulomb or Drucker-Prager criterion. For nonhydrostatic loading, the stress state at the onset of shear-enhanced compaction was predicted to fall on a linear cap according to the Mohr-Coulomb criterion. In contrast, nonlinear caps in qualitative agreement with laboratory data were predicted using the Drucker-Prager criterion. Our micromechanical model implies that the effective medium is significantly stronger and relatively pressure-insensitive in comparison to the bulk sample.

ENGINEERING APPLICATION AND ECONOMICS OF LIMB (LIMESTONE INJECTION/MULTISTAGE BURNERS)

EPA Science Inventory

The paper describes the use of an EPA LIMB cost model, in conjunction with cost and performance models for flue gas desulfurization (FGD), to compare these two technologies under similar premises. (NOTE: The performance goals of LIMB, EPA's acronym for Limestone Injection/Multist...

Detail view to show one of the limestone relief panels ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Detail view to show one of the limestone relief panels depicting one of the agencies of the Commerce Department, here the Lighthouse Service - United States Department of Commerce, Bounded by Fourteenth, Fifteenth, and E streets and Constitution Avenue, Washington, District of Columbia, DC

27 CFR 478.59 - Abandoned application.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2011-04-01 2010-04-01 true Abandoned application. 478.59 Section 478.59 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Licenses § 478...

27 CFR 478.59 - Abandoned application.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Abandoned application. 478.59 Section 478.59 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Licenses § 478...

27 CFR 478.59 - Abandoned application.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2012-04-01 2010-04-01 true Abandoned application. 478.59 Section 478.59 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Licenses § 478...

27 CFR 478.59 - Abandoned application.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Abandoned application. 478.59 Section 478.59 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Licenses § 478...

27 CFR 478.59 - Abandoned application.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Abandoned application. 478.59 Section 478.59 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO, FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION COMMERCE IN FIREARMS AND AMMUNITION Licenses § 478...

37 CFR 1.138 - Express abandonment.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 37 Patents, Trademarks, and Copyrights 1 2014-07-01 2014-07-01 false Express abandonment. 1.138 Section 1.138 Patents, Trademarks, and Copyrights UNITED STATES PATENT AND TRADEMARK OFFICE, DEPARTMENT OF COMMERCE GENERAL RULES OF PRACTICE IN PATENT CASES National Processing Provisions Time for Reply by...

37 CFR 1.138 - Express abandonment.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 37 Patents, Trademarks, and Copyrights 1 2013-07-01 2013-07-01 false Express abandonment. 1.138 Section 1.138 Patents, Trademarks, and Copyrights UNITED STATES PATENT AND TRADEMARK OFFICE, DEPARTMENT OF COMMERCE GENERAL RULES OF PRACTICE IN PATENT CASES National Processing Provisions Time for Reply by...

37 CFR 1.138 - Express abandonment.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 37 Patents, Trademarks, and Copyrights 1 2011-07-01 2011-07-01 false Express abandonment. 1.138 Section 1.138 Patents, Trademarks, and Copyrights UNITED STATES PATENT AND TRADEMARK OFFICE, DEPARTMENT OF COMMERCE GENERAL RULES OF PRACTICE IN PATENT CASES National Processing Provisions Time for Reply by...

37 CFR 1.138 - Express abandonment.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 37 Patents, Trademarks, and Copyrights 1 2012-07-01 2012-07-01 false Express abandonment. 1.138 Section 1.138 Patents, Trademarks, and Copyrights UNITED STATES PATENT AND TRADEMARK OFFICE, DEPARTMENT OF COMMERCE GENERAL RULES OF PRACTICE IN PATENT CASES National Processing Provisions Time for Reply by...

The Miocene Nullarbor Limestone, southern Australia; deposition on a vast subtropical epeiric platform

NASA Astrophysics Data System (ADS)

O'Connell, Laura G.; James, Noel P.; Bone, Yvonne

2012-05-01

The early to middle Miocene Nullarbor Limestone forms the vast, karsted Nullarbor Plain in southern Australia, and may be the most extensive Miocene carbonate deposit described to date. These carbonates were deposited at southern paleolatitudes of ~ 40°S and are interpreted to be subtropical to warm-temperate in character because of the presence of certain genera of tropical coralline algae (rhodoliths and articulated types), large benthic foraminifera, tropical molluscs, zooxanthellate corals, and micrite envelopes. Facies are dominated by skeletal grainstones and floatstones that accumulated in three interpreted paleoenvironments: (1) seagrass banks (upper photic zone), (2) rhodolith pavements (lower photic zone), and (3) open seafloors (lower photic to subphotic zone). A decrease of tropical components from west to east across the platform implies that warm oceanic currents (possibly related to a proto-Leeuwin Current), as well as a period of warm climate (Miocene Climatic Optimum), resulted in subtropical deposition at southern latitudes. The Southern Ocean extended inboard ~ 450 km from the shelf edge during Nullarbor Limestone deposition, but interpreted paleodepths did not extend much below the base of the photic zone. A small slope angle (~ 0.02°) over a wide shelf (~ 300,000 km2) implies deposition on an epeiric platform or epeiric ramp. A Miocene barrier reef was likely coeval with Nullarbor Limestone deposition. Therefore, the inboard portion of the Nullarbor Limestone can be considered part of an extensive back-reef lagoon system on a rimmed epeiric platform, perhaps attaining a size similar to the modern Great Barrier Reef system.

Relation of historical quarrying, material utilization and performance on buildings in Eastern Finland

NASA Astrophysics Data System (ADS)

Luodes, Nike M.; Pirinen, Heikki

2016-04-01

Finland might seem to have lower stone heritage compared to other southern European countries, but it has been the main exporter of dimension stone to the majestic buildings that made St.Petersburg a recognized cultural heritage. In Finland, though, the stone seems undervalued. The only dramatic and predominant stone buildings are those of agencies and administrations located in the towns, where the stone has been used to impress and symbolize value. Romantic style used massive bossy stone in building's full height and created fine traditional carvings. Otherwise the communities have mainly built settlements in contact with the nature, with materials easily available and of low cost, following architectonical trends of the periods and producing interesting stone details. During the past years, research has been conducted on historical buildings interconnecting scientific and artistic approach to evaluate material durability and cultural relevance of the artifacts. Generally until mid 20th century the stone has been traditionally used massive for basements and walls. The materials still present good mechanical characteristics and most often the weathering level after hundreds of years of exposure had reached only the first millimeters from the curst. Instead the old methodology for deposit exploitation has left visible signs on the buildings. Some examples are visible from Kuopio. The exploitation of small, easy-to-reach surface deposits, even if planned by local experts, has affected quality and appearance of historical buildings. As an example the excavation of shallow quarries where also weathered crop was kept as a product has characterized the basement of the Niirala school that presents change in colors due to original material more than to weathering on site. Fissuring is also visible on a couple of blocks while marks on the rocks depict the old excavation method. Most often the deposits had been in the vicinities, frequently hidden by further construction

Successional trends in Sonoran Desert abandoned agricultural fields in northern Mexico

USGS Publications Warehouse

Castellanos, A.E.; Martinez, M.J.; Llano, J.M.; Halvorson, W.L.; Espiricueta, M.; Espejel, I.

2005-01-01

Excessive ground-water use and saline intrusion to the aquifer led, in less than three decades, to an increase in abandoned agricultural fields at La Costa de Hermosillo, within the Sonoran Desert. Using a chronosequence from years since abandonment, patterns of field succession were developed. Contrary to most desert literature, species replacement was found, both in fields with and without saline intrusion. Seasonal photosynthetic capacity as well as water and nitrogen use efficiencies were different in dominant early and late successional plant species. These ecological findings provided a framework for a general explanation of species dominance and replacement within abandoned agricultural fields in the Sonoran Desert. ?? 2004 Elsevier Ltd. All rights reserved.

Limestone characterization to model damage from acidic precipitation: Effect of pore structure on mass transfer

USGS Publications Warehouse

Leith, S.D.; Reddy, M.M.; Irez, W.F.; Heymans, M.J.

1996-01-01

The pore structure of Salem limestone is investigated, and conclusions regarding the effect of the pore geometry on modeling moisture and contaminant transport are discussed based on thin section petrography, scanning electron microscopy, mercury intrusion porosimetry, and nitrogen adsorption analyses. These investigations are compared to and shown to compliment permeability and capillary pressure measurements for this common building stone. Salem limestone exhibits a bimodal pore size distribution in which the larger pores provide routes for convective mass transfer of contaminants into the material and the smaller pores lead to high surface area adsorption and reaction sites. Relative permeability and capillary pressure measurements of the air/water system indicate that Salem limestone exhibits high capillarity end low effective permeability to water. Based on stone characterization, aqueous diffusion and convection are believed to be the primary transport mechanisms for pollutants in this stone. The extent of contaminant accumulation in the stone depends on the mechanism of partitioning between the aqueous and solid phases. The described characterization techniques and modeling approach can be applied to many systems of interest such as acidic damage to limestone, mass transfer of contaminants in concrete and other porous building materials, and modeling pollutant transport in subsurface moisture zones.

Fluorspar

USGS Publications Warehouse

Miller, M.

2013-01-01

World fluorspar demand slowed in 2012 and, according to some sources prices decreased, especially in the latter half of the year. In 2012, nearly all fluorspar (CaF2) consumption in the United States was from imports. Hastie Mining and Trucking Co. produced some fluorspar as a byproduct of its limestone quarry operations in Illinois. In addition, a small amount of usable synthetic fluorspar was produced from industrial waste streams.

Selection, procurement and description of Salem Limestone samples used to study the effects of acid rain

NASA Astrophysics Data System (ADS)

Ross, M.; Knab, L.

1984-07-01

The selection, procurement, and description of the Salem Limestone to be used in field exposure tests to assess the effects of acid rain on building stone are described. The rationale for choosing Salem Limestone is given and a brief geological description of the stone is provided. Preparation of the stone samples for field exposure, including cutting, surface finishing and labelling is presented.

Properties, sustainability and elevated temperature behavior of concrete containing Portland limestone cement

NASA Astrophysics Data System (ADS)

El-Hawary, Moetaz; Ahmed, Mahmoud

2017-09-01

The utilization of some type of cheap filler as partial cement replacement is an effective way of improving concrete sustainability. With the recent trends to reduce water to cement ratio and improve compaction, there is no enough space or water for complete hydration of cement. This means that actually, a portion of mixed cement acts as expensive filler. Replacing this portion with cheaper filler that requires less energy to produce is, therefore, beneficial. Crushed limestone is the most promising filler. This work is to investigate the effect of the amount of limestone fillers on the sustainability and the fresh and mechanical properties of the resulting concrete. A rich mix is designed with a low water/cement ratio of 0.4. Lime is introduced as a replacement percentage of cement. Ratios of 0, 10, 20 and 30% were used. Slump, compressive strength, specific gravity and water absorption are evaluated for every mix. In addition, the effect of the amount of lime on the residual strength of concrete subjected to elevated temperatures is also investigated. Samples are subjected to six different temperature stations of 20, 100, 200, 300, 500 and 700°C for six hours before being cooled and subsequently tested for compressive strength and specific gravity. Sustainability of the tested mixes is evaluated through reductions in the emitted carbon dioxide, energy and reduction in cost. Based on the annual use of concrete in Kuwait, the sustainability benefits resulting from the use of limestone filler in Kuwait are evaluated and assessed. The paper is concluded with the recommendation of the use of 15% limestone filler as partial cement replacement where the properties and the behavior under high temperature of the resulting concrete are almost the same as those of conventional concrete with considerable cost and sustainability benefits.

48 CFR 45.603 - Abandonment, destruction or donation of excess personal property.

Code of Federal Regulations, 2010 CFR

2010-10-01

... or donation of excess personal property. 45.603 Section 45.603 Federal Acquisition Regulations System... Disposal 45.603 Abandonment, destruction or donation of excess personal property. (a) Plant clearance... any of the costs incident to a donation. (d)(1) Before abandoning, destroying, or donating excess...

48 CFR 45.604-2 - Abandonment, destruction, or donation of surplus property.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., or donation of surplus property. 45.604-2 Section 45.604-2 Federal Acquisition Regulations System... Disposal 45.604-2 Abandonment, destruction, or donation of surplus property. (a) Plant clearance officers... the costs incident to donation. (d) Before abandoning, destroying, or donating surplus property, the...

48 CFR 945.603 - Abandonment, destruction or donation of excess personal property.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 5 2014-10-01 2014-10-01 false Abandonment, destruction or donation of excess personal property. 945.603 Section 945.603 Federal Acquisition Regulations... Disposal 945.603 Abandonment, destruction or donation of excess personal property. See 945.670 for DOE...

48 CFR 45.603 - Abandonment, destruction or donation of excess personal property.

Code of Federal Regulations, 2011 CFR

2011-10-01

... or donation of excess personal property. 45.603 Section 45.603 Federal Acquisition Regulations System... Disposal 45.603 Abandonment, destruction or donation of excess personal property. (a) Plant clearance... any of the costs incident to a donation. (d)(1) Before abandoning, destroying, or donating excess...

48 CFR 45.604-2 - Abandonment, destruction, or donation of surplus property.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., or donation of surplus property. 45.604-2 Section 45.604-2 Federal Acquisition Regulations System... Disposal 45.604-2 Abandonment, destruction, or donation of surplus property. (a) Plant clearance officers... the costs incident to donation. (d) Before abandoning, destroying, or donating surplus property, the...

48 CFR 945.603 - Abandonment, destruction or donation of excess personal property.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 5 2013-10-01 2013-10-01 false Abandonment, destruction or donation of excess personal property. 945.603 Section 945.603 Federal Acquisition Regulations... Disposal 945.603 Abandonment, destruction or donation of excess personal property. See 945.670 for DOE...

Paleokarst processes in the Eocene limestones of the Pyramids Plateau, Giza, Egypt

NASA Astrophysics Data System (ADS)

El Aref, M. M.; Refai, E.

The Eocene limestones of the Pyramids plateau are characterized by landforms of stepped terraced escarpment and karst ridges with isolated hills. The carbonate country rocks are also dominated by minor surface, surface to subsurface and subsurface solution features associated with karst products. The systematic field observations eludicate the denudation trend of the minor solution features and suggest the origin of the regional landscapes. The lithologic and structural characters of the limestone country rocks comprise the main factors controlling the surface and subsurface karst evolution. The development of the karst features and the associated sediments in the study area provides information on the paleohydrolic, chemical and climatic environments involved in the origin of the karstification.

Long-term Quaternary uplift rates inferred from limestone caves in Sarawak, Malaysia

NASA Astrophysics Data System (ADS)

Farrant, Andrew R.; Smart, Peter L.; Whitaker, Fiona F.; Tarling, Donald H.

1995-04-01

The rate of long-term (2 m.y.) base-level lowering estimated in an extensive sequence of limestone caves in Sarawak, Malaysia, from uranium series, electron spin resonance, and paleomagnetic dating is 0.19 +0.03/-0.04 m/ka. This rate has remained constant over at least the last 700 ka, as shown by comparison of the number and spacing of wall notches formed during phases of interstadial and interglacial aggradation with peaks in the deep-sea oxygen isotope curve. It is argued that base-level lowering occurs in response to epirogenic uplift of the more resistant limestones due to regional denudation of the softer shales, and to flexural isostacy associated with high rates of offshore sedimentation.

23 CFR 752.10 - Abandoned vehicles.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 23 Highways 1 2010-04-01 2010-04-01 false Abandoned vehicles. 752.10 Section 752.10 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RIGHT-OF-WAY AND ENVIRONMENT LANDSCAPE AND..., or enhancement of scenic beauty as seen from the traveled way of the highway as a landscape or...

23 CFR 752.10 - Abandoned vehicles.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 23 Highways 1 2011-04-01 2011-04-01 false Abandoned vehicles. 752.10 Section 752.10 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RIGHT-OF-WAY AND ENVIRONMENT LANDSCAPE AND..., or enhancement of scenic beauty as seen from the traveled way of the highway as a landscape or...

23 CFR 752.10 - Abandoned vehicles.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 23 Highways 1 2013-04-01 2013-04-01 false Abandoned vehicles. 752.10 Section 752.10 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RIGHT-OF-WAY AND ENVIRONMENT LANDSCAPE AND..., or enhancement of scenic beauty as seen from the traveled way of the highway as a landscape or...

23 CFR 752.10 - Abandoned vehicles.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 23 Highways 1 2014-04-01 2014-04-01 false Abandoned vehicles. 752.10 Section 752.10 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RIGHT-OF-WAY AND ENVIRONMENT LANDSCAPE AND..., or enhancement of scenic beauty as seen from the traveled way of the highway as a landscape or...

23 CFR 752.10 - Abandoned vehicles.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 23 Highways 1 2012-04-01 2012-04-01 false Abandoned vehicles. 752.10 Section 752.10 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RIGHT-OF-WAY AND ENVIRONMENT LANDSCAPE AND..., or enhancement of scenic beauty as seen from the traveled way of the highway as a landscape or...

Long-Term Effectiveness, under a Mountain Environment, of a Novel Conservation Nanomaterial Applied on Limestone from a Roman Archaeological Site.

PubMed

Elhaddad, Farid; Carrascosa, Luis A M; Mosquera, Maria J

2018-04-28

A novel alkoxysilane-based product was applied on limestone samples from a Roman archaeological site. The study consisted of an initial phase to evaluate site environmental conditions in order to choose the most suitable product type to be applied. The decay that was produced in the site is mainly caused by natural action, with water being the main vehicle for the decay agents. Thus, the effectiveness of an innovative product with hydrophobic/consolidant properties and two commercial products (consolidant and hydrophobic agent) were evaluated on limestone from Acinipo site, under laboratory conditions. Next, the long-term effectiveness of the three products under study was evaluated by the exposure of limestone samples in the archaeological site for a period of three years. Since the recognized incompatibility between alkoxysilanes and pure carbonate stones, the interaction between the products and the limestones was widely investigated. The results that were obtained allow for it to be concluded that the innovative product presents adequate compatibility and adherence to the limestone under study, producing a long-term effective, homogeneous, and continuous coating with a depth of penetration of up to 10 mm. However, the commercial products produced discontinuous aggregates on the limestone surface, did not penetrate into its porous structure and it did not produce long-lasting effects.

Stress Related Fracturing in Dimension Stone Quarries

NASA Astrophysics Data System (ADS)

Hamdi Deliormanli, Ahmet; Maerz, Norbert H.

2016-10-01

In Missouri, the horizontal stresses (pressures) in the near surface rock are uncommonly high. While the vertical stresses in rock are simply a function of the weight of the overlying rock, near surface stresses can be many times higher. The near surface horizontal stresses can be in excess of 5 times greater than the vertical stresses. In this research, Flatjack method was used to measure horizontal stress in Red Granite Quarry in Missouri. The flat jack method is an approved method of measuring ground stresses. A saw cut is used to “relax” the stress in the ground by allowing the rock to deform inwards the cut. A hydraulic flat jack is used to inflate the slot; to push the rock back to its stressed position, as measured by a strain gauge on either side of the slot. The pressure in the jack, when the rock is exactly back to its original position, is equal to the ground stress before the saw cut was made. According to the results, present production direction for each pit is not good because the maximum stress direction is perpendicular with production direction. This case causes unintentional breakage results in the loss rock. The results show that production direction should be changed.

Ecotoxicological risk assessment linked to infilling quarries with treated dredged seaport sediments.

PubMed

Perrodin, Yves; Donguy, Gilles; Bazin, Christine; Volatier, Laurence; Durrieu, Claude; Bony, Sylvie; Devaux, Alain; Abdelghafour, Mohammed; Moretto, Robert

2012-08-01

The dredged sediments of polluted seaports now raise complex management problems since it is no longer possible to discharge them into the sea. This results in the need to manage them on land, raising other types of technical, economic and environmental problems. Regarding the technical and economic dimensions, traditional waste treatment methods have proved to be poorly adapted, due to very high costs and low absorbable volumes. In this context, filling quarries in coastal areas with treated sediments could represent an interesting alternative for these materials. Nevertheless, for the environmental dimension, it is necessary to demonstrate that this possibility is harmless to inland ecosystems. Consequently, a specific ecotoxicological risk assessment methodology has been formulated and tested on three sediments taken from seaboards of France, in view to providing an operational and usable tool for the prior validation of any operation to fill quarries with treated seaport sediments. This method incorporates the formulation of a global conceptual model of the scenario studied and the definition of protocols for each of its steps: the characterisation of exposures (based on a simulation of sediment deposit), the characterisation of effects (via the study of sediments ecotoxicity), and the final ecotoxicological risk assessment performed as a calculation of a risk quotient. It includes the implementation in parallel of two types of complementary approach: the "substances" approach derived from the European methodology for assessing new substances placed on the market, and the "matrix" approach which is similar to methods developed in France to assess ecological risks in other domains (waste management, polluted site management, …). The application of this dual approach to the three sediments tested led to conclude with reliability that the project to deposit sediments "1" and "2" presented a low risk for the peripheral aquatic ecosystems while sediment "3

Oscar Renda Contracting Inc. Navajo Nation Crushing/Screening Operation: Coverage Under General Air Quality Permit for Stone Quarrying, Crushing and Screening Facilities

EPA Pesticide Factsheets

Documents related to approved request for coverage under the Stone Quarrying, Crushing and Screening Facilities General Permit for Oscar Renda Contracting Inc. Navajo Nation Crushing/Screening Operation located in McKinley and San Juan Counties, NM.

Tree Diameter Growth in the Dry Limestone Hills

Treesearch

C. B. Briscoe

1962-01-01

The dry limestone hill region of southwestern Puerto Rico, because of heavy, shallow soils and scant rainfall is not farmed, and is recognized as an area best suited for the growth of trees. With a mean temperature near 80°F and with rainfall averaging no more than 30 inches anually and much less during dry years, the site is adverse even for tree growth. Studies on...

Dolomitization of Quaternary reef limestones, Aitutaki, Cook Islands

USGS Publications Warehouse

Hein, J.R.; Gray, S.C.; Richmond, B.M.; White, L.D.

1992-01-01

The primary reef framework is considered to have been deposited during several highstands of sea level. Following partial to local recrystallization of the limestone, a signle episode of dolomitization occurred. Both tidal and thermal pumping drove large quantities of seawater through the porous rocks and perhaps maintained a wide mixing zone. However, the isotopic, geochemical and petrographic data do not clearly indicate the extent of seawater mixing. -from Authors

A Combined Remote Sensing-Numerical Modelling Approach to the Stability Analysis of Delabole Slate Quarry, Cornwall, UK

NASA Astrophysics Data System (ADS)

Havaej, Mohsen; Coggan, John; Stead, Doug; Elmo, Davide

2016-04-01

Rock slope geometry and discontinuity properties are among the most important factors in realistic rock slope analysis yet they are often oversimplified in numerical simulations. This is primarily due to the difficulties in obtaining accurate structural and geometrical data as well as the stochastic representation of discontinuities. Recent improvements in both digital data acquisition and incorporation of discrete fracture network data into numerical modelling software have provided better tools to capture rock mass characteristics, slope geometries and digital terrain models allowing more effective modelling of rock slopes. Advantages of using improved data acquisition technology include safer and faster data collection, greater areal coverage, and accurate data geo-referencing far exceed limitations due to orientation bias and occlusion. A key benefit of a detailed point cloud dataset is the ability to measure and evaluate discontinuity characteristics such as orientation, spacing/intensity and persistence. This data can be used to develop a discrete fracture network which can be imported into the numerical simulations to study the influence of the stochastic nature of the discontinuities on the failure mechanism. We demonstrate the application of digital terrestrial photogrammetry in discontinuity characterization and distinct element simulations within a slate quarry. An accurately geo-referenced photogrammetry model is used to derive the slope geometry and to characterize geological structures. We first show how a discontinuity dataset, obtained from a photogrammetry model can be used to characterize discontinuities and to develop discrete fracture networks. A deterministic three-dimensional distinct element model is then used to investigate the effect of some key input parameters (friction angle, spacing and persistence) on the stability of the quarry slope model. Finally, adopting a stochastic approach, discrete fracture networks are used as input for 3D

Geological Prediction Ahead of Tunnel Face in the Limestone Formation Tunnel using Multi-Modal Geophysical Surveys

NASA Astrophysics Data System (ADS)

Zaki, N. F. M.; Ismail, M. A. M.; Hazreek Zainal Abidin, Mohd; Madun, Aziman

2018-04-01

Tunnel construction in typical karst topography face the risk which unknown geological condition such as abundant rainwater, ground water and cavities. Construction of tunnel in karst limestone frequently lead to potentially over-break of rock formation and cause failure to affected area. Physical character of limestone which consists large cavity prone to sudden failure and become worsen due to misinterpretation of rock quality by engineer and geologists during analysis stage and improper method adopted in construction stage. Consideration for execution of laboratory and field testing in rock limestone should be well planned and arranged in tunnel construction project. Several tests including Ground Penetration Radar (GPR) and geological face mapping were studied in this research to investigate the performances of limestone rock in tunnel construction, measured in term of rock mass quality that used for risk assessment. The objective of this study is to focus on the prediction of geological condition ahead of tunnel face using short range method (GPR) and verified by geological face mapping method to determine the consistency of actual geological condition on site. Q-Value as the main indicator for rock mass classification was obtained from geological face mapping method. The scope of this study is covering for tunnelling construction along 756 meters in karst limestone area which located at Timah Tasoh Tunnel, Bukit Tebing Tinggi, Perlis. For this case study, 15% of GPR results was identified as inaccurate for rock mass classification in which certain chainage along this tunnel with 34 out of 224 data from GPR was identified as incompatible with actual face mapping.

Petrophysical and transport parameters evolution during acid percolation through structurally different limestones

NASA Astrophysics Data System (ADS)

Martinez Perez, Laura; Luquot, Linda

2017-04-01

Processes affecting geological media often show complex and unpredictable behavior due to the presence of heterogeneities. This remains problematic when facing contaminant transport problems, in the CO2 storage industry or dealing with the mechanisms underneath natural processes where chemical reactions can be observed during the percolation of rock non-equilibrated fluid (e.g. karst formation, seawater intrusion). To understand the mechanisms taking place in a porous medium as a result of this water-rock interaction, we need to know the flow parameters that control them, and how they evolve with time as a result of that concurrence. This is fundamental to ensure realistic predictions of the behavior of natural systems in response of reactive transport processes. We investigate the coupled influence of structural and hydrodynamic heterogeneities in limestone rock samples tracking its variations during chemical reactions. To do so we use laboratory petrophysical techniques such as helium porosimetry, gas permeability, centrifugue, electrical resistivity and sonic waves measurements to obtain the parameters that characterize flow within rock matrix (porosity, permeability, retention curve and pore size distribution, electrical conductivity, formation factor, cementation index and tortuosity) before and after percolation experiments. We built an experimental setup that allows injection of acid brine into core samples under well controlled conditions, monitor changes in hydrodynamic properties and obtain the chemical composition of the injected solution at different stages. 3D rock images were also acquired before and after the experiments using a micro-CT to locate the alteration processes and perform an acurate analysis of the structural changes. Two limestones with distinct textural classification and thus contrasting transport properties have been used in the laboratory experiments: a crinoid limestone and an oolithic limestone. Core samples dimensions were 1 inch

7 CFR 97.22 - Revival of an application abandoned for failure to reply.

Code of Federal Regulations, 2010 CFR

2010-01-01

... regulations in this part, may be revived as a pending application within 3 months of such abandonment, upon a.... A request to revive an abandoned application shall be accompanied by a written statement showing the...

14. A VIEW SOUTHEAST OF A PORTION OF THE LIMESTONE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. A VIEW SOUTHEAST OF A PORTION OF THE LIMESTONE ABUTMENT, THE UNDERSIDE OF THE INCLINED END POST AND A PLATE USED TO ATTACH THE STRUCTURE TO THE ABUTMENT. - Wells County Bridge No. 74, Spanning Rock Creek Ditch at County Road 400, Bluffton, Wells County, IN

Preservation of York Minster historic limestone by hydrophobic surface coatings

PubMed Central

Walker, Rachel A.; Wilson, Karen; Lee, Adam F.; Woodford, Julia; Grassian, Vicki H.; Baltrusaitis, Jonas; Rubasinghege, Gayan; Cibin, Giannantonio; Dent, Andrew

2012-01-01

Magnesian limestone is a key construction component of many historic buildings that is under constant attack from environmental pollutants notably by oxides of sulfur via acid rain, particulate matter sulfate and gaseous SO2 emissions. Hydrophobic surface coatings offer a potential route to protect existing stonework in cultural heritage sites, however, many available coatings act by blocking the stone microstructure, preventing it from ‘breathing' and promoting mould growth and salt efflorescence. Here we report on a conformal surface modification method using self-assembled monolayers of naturally sourced free fatty acids combined with sub-monolayer fluorinated alkyl silanes to generate hydrophobic (HP) and super hydrophobic (SHP) coatings on calcite. We demonstrate the efficacy of these HP and SHP surface coatings for increasing limestone resistance to sulfation, and thus retarding gypsum formation under SO2/H2O and model acid rain environments. SHP treatment of 19th century stone from York Minster suppresses sulfuric acid permeation. PMID:23198088

Preservation of York Minster historic limestone by hydrophobic surface coatings.

PubMed

Walker, Rachel A; Wilson, Karen; Lee, Adam F; Woodford, Julia; Grassian, Vicki H; Baltrusaitis, Jonas; Rubasinghege, Gayan; Cibin, Giannantonio; Dent, Andrew

2012-01-01

Magnesian limestone is a key construction component of many historic buildings that is under constant attack from environmental pollutants notably by oxides of sulfur via acid rain, particulate matter sulfate and gaseous SO(2) emissions. Hydrophobic surface coatings offer a potential route to protect existing stonework in cultural heritage sites, however, many available coatings act by blocking the stone microstructure, preventing it from 'breathing' and promoting mould growth and salt efflorescence. Here we report on a conformal surface modification method using self-assembled monolayers of naturally sourced free fatty acids combined with sub-monolayer fluorinated alkyl silanes to generate hydrophobic (HP) and super hydrophobic (SHP) coatings on calcite. We demonstrate the efficacy of these HP and SHP surface coatings for increasing limestone resistance to sulfation, and thus retarding gypsum formation under SO(2)/H(2)O and model acid rain environments. SHP treatment of 19th century stone from York Minster suppresses sulfuric acid permeation.

Preservation of York Minster historic limestone by hydrophobic surface coatings

NASA Astrophysics Data System (ADS)

Walker, Rachel A.; Wilson, Karen; Lee, Adam F.; Woodford, Julia; Grassian, Vicki H.; Baltrusaitis, Jonas; Rubasinghege, Gayan; Cibin, Giannantonio; Dent, Andrew

2012-11-01

Magnesian limestone is a key construction component of many historic buildings that is under constant attack from environmental pollutants notably by oxides of sulfur via acid rain, particulate matter sulfate and gaseous SO2 emissions. Hydrophobic surface coatings offer a potential route to protect existing stonework in cultural heritage sites, however, many available coatings act by blocking the stone microstructure, preventing it from `breathing' and promoting mould growth and salt efflorescence. Here we report on a conformal surface modification method using self-assembled monolayers of naturally sourced free fatty acids combined with sub-monolayer fluorinated alkyl silanes to generate hydrophobic (HP) and super hydrophobic (SHP) coatings on calcite. We demonstrate the efficacy of these HP and SHP surface coatings for increasing limestone resistance to sulfation, and thus retarding gypsum formation under SO2/H2O and model acid rain environments. SHP treatment of 19th century stone from York Minster suppresses sulfuric acid permeation.

76 FR 12222 - Wisconsin Central, Ltd.-Abandonment Exemption-in Marathon County, WI

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-04

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. AB 303 (Sub-No. 37X)] Wisconsin Central, Ltd.--Abandonment Exemption--in Marathon County, WI Wisconsin Central, Ltd. (WCL), filed... to abandon 1.14 miles of rail line between mileposts 17.50 and 18.64, in Weston, Marathon County, Wis...

Assessing the effect of agricultural land abandonment on bird communities in southern-eastern Europe.

PubMed

Zakkak, Sylvia; Radovic, Andreja; Nikolov, Stoyan C; Shumka, Spase; Kakalis, Lefteris; Kati, Vassiliki

2015-12-01

Agricultural land abandonment is recognized as a major environmental threat in Europe, being particularly pronounced in south-eastern Europe, where knowledge on its effects is limited. Taking the Balkan Peninsula as a case study, we investigated agricultural abandonment impact on passerine communities at regional level. We set up a standard methodology for site selection (70 sites) and data collection, along a well-defined forest-encroachment gradient that reflects land abandonment in four countries: Albania, Bulgaria, Croatia and Greece. Regardless the different socio-economic and political histories in the Balkans that led to diverse land abandonment patterns in space and time, rural abandonment had a consistent negative effect on bird communities, while regional-level analysis revealed patterns that were hidden at local level. The general trends were an increase of forest-dwelling bird species at the expense of farmland birds, the decline of overall bird species richness, as well as the decline of Species of European Conservation Concern (SPECs) richness and abundance. Many farmland bird species declined with land abandonment, whereas few forest species benefited from the process. In conclusion, our results support CAP towards hampering rural land abandonment and preserving semi-open rural mosaics in remote upland areas, using a suite of management measures carefully tailored to local needs. The maintenance of traditional rural landscapes should be prioritized in the Balkans, through the timely identification of HNV farmland that is most prone to abandonment. We also suggest that coordinated transnational research is needed, for a better assessment of conservation options in remote rural landscapes at European scale, including the enhancement of wild grazers' populations as an alternative in areas where traditional land management is rather unlikely to be re-established. Copyright © 2015 Elsevier Ltd. All rights reserved.

Rock Magnetic Cyclostratigraphy of the Mid-Cretaceous Greenhorn Limestone, South-Central Colorado---Influence of Orbitally Induced Climate Variability for Chornostratigraphy

NASA Astrophysics Data System (ADS)

Sellers, T.; Geissman, J. W.; Jackson, J.

2015-12-01

We are testing the hypothesis that depositional processes of the mid-Cretaceous Greenhorn Limestone were influenced by orbitally-driven climate variations using rock magnetic data. Correlation of the data, including anhysteretic remanent magnetization (ARM), magnetic susceptibility, isothermal remanent magnetization in different DC fields to saturation, and hysteresis properties, from three continuously exposed sections of the full Greenhorn Limestone provides detailed spatial distribution for the depositional processes and magnetic mineral climate encoding. The Greenhorn Limestone includes the Lincoln Limestone, Hartland Shale, and the Bridge Creek Limestone members and consists of calcareous shales and limestones representing near maximum depths in the Cretaceous interior seaway. The sections, each about 30 m thick, extend from the upper Graneros Shale, through the Greenhorn Formation, to the lower Carlisle Shale, with samples collected at a two to five cm interval and are located at Badito, CO; north of Redwing, CO; and at the Global boundary Stratotype Section and Point (GSSP) at Lake Pueblo, CO. Our over 1000 samples were hand crushed to granule size pieces and packed into 7cc IODP boxes. Bulk magnetic susceptibility, anhysteretic remanent magnetization (ARM) intensity at different peak AF levels, and isothermal remanent magnetization (IRM) intensity record variations in magnetic mineral concentration and are proxies to determine orbital scale cycles and precise stratigraphic correlation between sections. ARM intensities in a peak field of 100 mT at both sites range between 1.2 x 10-3 and 1.3 x 10-4 A/m and better define periodic variation within the Greenhorn Limestone displaying differences in ferromagnetic mineral content of detrital origin. Magnetic susceptibility, which ranges from 3.5 x 10-2 to 2.86 x 10-3, also shows periodic variation with a strong correlation among the three sections. Saturation IRM at 100 mT ranges from 3.2 x 10-1 to 1.1x 10-2 A

Discontinuity surfaces and event stratigraphy of Okha Shell Limestone Member: Implications for Holocene sea level changes, western India

NASA Astrophysics Data System (ADS)

Bhonde, Uday; Desai, Bhawanisingh G.

2011-08-01

The Okha Shell Limestone Member of Chaya Formation is the coarse grained, shell rich deposit commonly recognized as the beach rocks. It has been age bracketed between Late Pleistocene and Holocene. Late Quaternary sea level changes have been studied with beach rocks along the Saurashtra coastal region. The present study has been carried out in the Okhamandal area of the Saurashtra peninsula especially on the Okha Shell Limestone Member as exposed at various locations along the coast from north to south. Temporal and spatial correlations of the observations have revealed three events in the Okha Shell Limestone Member of Chaya Formation that are correlated laterally. The events show depositional breaks represented by discontinuity surfaces, the taphofacies varieties and ichnological variations. The present study in the context of available geochrnological data of the region suggests a prominent depositional break representing low sea level stand (regression) during an Early Holocene during the deposition of Okha Shell Limestone Member.

Identification of Calcium Sulphoaluminate Formation between Alunite and Limestone

PubMed Central

Kim, Hyung-Seok; Han, Gi-Chun; Ahn, Ji-Whan; Cho, Kye-Hong; Cho, Hee-Chan

2009-01-01

This study was carried out to identify the conditions of formation of calcium sulphoaluminate (3CaO·3Al2O3·CaSO4) by the sintering of a limestone (CaCO3) and alunite [K2SO4·Al2(SO4)3·4Al(OH)3] mixture with the following reagents: K2SO4, CaCO3, Al(OH)3, CaSO4·2H2O, and SiO2. When K2SO4, CaCO3, Al(OH)3, CaSO4·2H2O were mixed in molar ratios of 1:3:6:3 and sintered at 1,200∼1,300 °C, only 3CaO·3Al2O3·CaSO4 and calcium langbeinite (2CaSO4·K2SO4) were generated. With an amount of CaO that is less than the stoichiometric molar ratio, 3CaO·3Al2O3·CaSO4 was formed and anhydrite (CaSO4) did not react and remained behind. With the amount of CaSO4 that is less than the stoichiometric molar ratio, the amounts of 3CaO·3Al2O3·CaSO4 and 2CaSO4·K2SO4 decreased, and that of CaO·Al2O3 increased. In the K2SO4-CaO-Al2O3-CaSO4-SiO2 system, to stabilize the formation of 3CaO·3Al2O3·CaSO4, 2CaSO4·K2SO4, and β-2CaO·SiO2, the molar ratios of CaO: Al2O3: CaSO4 must be kept at 3:3:1 and that of CaO/SiO2, over 2.0; otherwise, the generated amount of 3CaO·3Al2O3·CaSO4 decreased and that of gehlenite (2CaO·Al2O3·SiO2) with no hydration increased quantitatively. Therefore, if all SO3(g) generated by the thermal decomposition of alunite reacts with CaCO3 (or CaO, the thermal decomposition product of limestone) to form CaSO4 in an alunite- limestone system, 1 mol of pure alunite reacts with 6 mol of limestone to form 1 mol of 3CaO·3Al2O3·CaSO4 and 1 mol of 2CaSO4·K2SO4. PMID:22346687

Comparison of Limestone and Ground Fish for Treatment of Nutritional Rickets in Children in Nigeria.

PubMed

Thacher, Tom D; Bommersbach, Tanner J; Pettifor, John M; Isichei, Christian O; Fischer, Philip R

2015-07-01

To determine whether children with calcium-deficiency rickets respond better to treatment with calcium as limestone or as ground fish. Nigerian children with active rickets (n = 96) were randomized to receive calcium as powdered limestone (920 mg of elemental calcium) or ground fish (952 mg of elemental calcium) daily for 24 weeks. Radiographic healing was defined as achieving a score of 1.5 or less on a 10-point scale. The median (range) age of enrolled children was 35 (6-151) months. Of the 88 children who completed the study, 29 (66%) in the ground fish group and 24 (55%) in the limestone group achieved the primary outcome of a radiographic score of 1.5 or less within 6 months (P = .39). The mean radiographic score improved from 6.2 ± 2.4 to 1.8 ± 2.2 in the ground fish group and from 6.3 ± 2.2 to 2.1 ± 2.4 in the limestone group (P = .68 for group comparison). In an intention to treat analysis adjusted for baseline radiographic score, age, milk calcium intake, and serum 25-hydroxyvitamin D concentration, the response to treatment did not differ between the 2 groups (P = .39). Younger age was associated with more complete radiographic healing in the adjusted model (aOR 0.74 [95% CI 0.57-0.92]). After 24 weeks of treatment, serum alkaline phosphatase had decreased, calcium and 25-hydroxyvitamin D increased, and bone mineral density increased in both groups, without significant differences between treatment groups. In children with calcium-deficiency rickets, treatment with calcium as either ground fish or limestone for 6 months healed rickets in the majority of children. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

5. Foreground: ore bridges, ore/coke/limestone bins, Detroit River; background: stock ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. Foreground: ore bridges, ore/coke/limestone bins, Detroit River; background: stock house on left, stripper building, BOF. Looking south/southwest - Rouge Steel Company, 3001 Miller Road, Dearborn, MI

The microbial nature of laminated limestones: Lessons from the Upper Aptian, Araripe Basin, Brazil

NASA Astrophysics Data System (ADS)

Catto, Bruno; Jahnert, Ricardo Jorge; Warren, Lucas Verissimo; Varejao, Filipe Giovanini; Assine, Mario Luis

2016-07-01

The Araripe Basin, located in northeastern Brazil, originated during the Gondwana continental break-up responsible for the opening of the South Atlantic during the Early Cretaceous. In the Araripe Basin, the post-rift Aptian sequence corresponds to the Santana Group, which is composed, in upward succession, of mostly clastic continental and rare carbonate layers of the Barbalha, Crato, Ipubi and Romualdo Formations. The laminated limestones of the Crato Formation were deposited in a lacustrine environment preceding the deposition of the Ipubi Formation evaporites. They are age-equivalent to the limestones of the pre-salt interval of the east coast of Brazil, which contains large petroleum reserves. The excellent preservation of its macrofossils has made the Crato Formation known worldwide as a Fossil Lagerstätte. The limestones are macroscopically homogeneous, and their deposition has been previously attributed to chemical precipitation. Although the carbonate laminites are macroscopically undifferentiated, mineralogical variations, microscopic texture and distinctive biotic aspects supported the characterization of four microfacies: planar laminated, crustiform, nodular and rhythmic. The microfacies analysis indicated a strong and pervasive biological activity in the Crato limestone morphogenesis. Organominerals precipitated by the metabolic action of cyanobacteria and/or sulfate-reducing bacteria and methanogenic-oxidizing archea are represented by calcite and pyrite. Calcified coccoid and filaments are common, furthermore, the presence of calcified biofilms composed of exopolymeric substances (EPS) is ubiquitous. The presence of amorphous organic matter (AOM) and gypsum, particularly in the rhythmic microfacies, indicates anoxic/dysoxic conditions and stressful environments during periods of drought and low lake levels which favored the development and preservation of microbial biofilms. Phytoclasts and miospores when present in the succession indicate an